WorldWideScience

Sample records for point sources located

  1. Location and release time identification of pollution point source in river networks based on the Backward Probability Method.

    Science.gov (United States)

    Ghane, Alireza; Mazaheri, Mehdi; Mohammad Vali Samani, Jamal

    2016-09-15

    The pollution of rivers due to accidental spills is a major threat to environment and human health. To protect river systems from accidental spills, it is essential to introduce a reliable tool for identification process. Backward Probability Method (BPM) is one of the most recommended tools that is able to introduce information related to the prior location and the release time of the pollution. This method was originally developed and employed in groundwater pollution source identification problems. One of the objectives of this study is to apply this method in identifying the pollution source location and release time in surface waters, mainly in rivers. To accomplish this task, a numerical model is developed based on the adjoint analysis. Then the developed model is verified using analytical solution and some real data. The second objective of this study is to extend the method to pollution source identification in river networks. In this regard, a hypothetical test case is considered. In the later simulations, all of the suspected points are identified, using only one backward simulation. The results demonstrated that all suspected points, determined by the BPM could be a possible pollution source. The proposed approach is accurate and computationally efficient and does not need any simplification in river geometry and flow. Due to this simplicity, it is highly recommended for practical purposes. Copyright © 2016. Published by Elsevier Ltd.

  2. A rotating modulation imager for locating mid-range point sources

    International Nuclear Information System (INIS)

    Kowash, B.R.; Wehe, D.K.; Fessler, J.A.

    2009-01-01

    Rotating modulation collimators (RMC) are relatively simple indirect imaging devices that have proven useful in gamma ray astronomy (far field) and have more recently been studied for medical imaging (very near field). At the University of Michigan a RMC has been built to study the performance for homeland security applications. This research highlights the imaging performance of this system and focuses on three distinct regions in the RMC field of view that can impact the search for hidden sources. These regions are a blind zone around the axis of rotation, a two mask image zone that extends from the blind zone to the edge of the field of view, and a single mask image zone that occurs when sources fall outside the field of view of both masks. By considering the extent and impact of these zones, the size of the two mask region can be optimized for the best system performance.

  3. Noise Source Location Optimization

    Directory of Open Access Journals (Sweden)

    Ed O’Keefe

    1994-01-01

    Full Text Available This article describes a method to determine locations of noise sources that minimize modal coupling in complex acoustic volumes. Using the acoustic source scattering capabilities of the boundary element method, predictions are made of mode shape and pressure levels due to various source locations. Combining knowledge of the pressure field with a multivariable function minimization technique, the source location generating minimum pressure levels can be determined. The analysis also allows for an objective comparison of “best/worst” locations. The technique was implemented on a personal computer for the U.S. Space Station, predicting 5–10 dB noise reduction using optimum source locations.

  4. Improved Dynamic Planar Point Location

    DEFF Research Database (Denmark)

    Brodal, Gerth Stølting; Arge, Lars; Georgiadis, Loukas

    2006-01-01

    We develop the first linear-space data structures for dynamic planar point location in general subdivisions that achieve logarithmic query time and poly-logarithmic update time.......We develop the first linear-space data structures for dynamic planar point location in general subdivisions that achieve logarithmic query time and poly-logarithmic update time....

  5. Near-field mass transport from a point source (instantaneously failed container) located in a disposal room

    International Nuclear Information System (INIS)

    Kolar, Miroslav; LeNeveu, Dennis M.

    1995-02-01

    One of the strategies for the disposal of nuclear fuel waste is to use very long-lived containers. There is a finite chance that a very small number of these containers would have initial manufacturing defects that would lead to pinhole-type failures at the time of, or shortly after, emplacement. If the vast majority of the containers are sufficiently long-lived, only the release from the initially defected containers need be considered in modeling release rates from the disposal vault. It has been assumed that the readily leachable fraction of the used fuel would dominate releases. This readily leachable fraction (often referred to as the instant release fraction) has been modeled as a point source at the location of the pinhole in the container. Containers are considered to be emplaced in long disposal rooms backfilled with clay mixed with crushed rock or sand. Numerical calculations are done for 129 I because it has the longest half-life among the readily leachable radionuclides that would be released from a failed container. (author). 13 refs., 1 tab., 18 figs

  6. Point Pollution Sources Dimensioning

    Directory of Open Access Journals (Sweden)

    Georgeta CUCULEANU

    2011-06-01

    Full Text Available In this paper a method for determining the main physical characteristics of the point pollution sources is presented. It can be used to find the main physical characteristics of them. The main physical characteristics of these sources are top inside source diameter and physical height. The top inside source diameter is calculated from gas flow-rate. For reckoning the physical height of the source one takes into account the relation given by the proportionality factor, defined as ratio between the plume rise and physical height of the source. The plume rise depends on the gas exit velocity and gas temperature. That relation is necessary for diminishing the environmental pollution when the production capacity of the plant varies, in comparison with the nominal one.

  7. Characteristics and locations of sources

    Energy Technology Data Exchange (ETDEWEB)

    Lahtinen, J.; Poellaenen, R.; Toivonen, H. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland)

    1997-12-31

    Ten artificial radiation sources were placed in the terrain in order to test the capability of airborne measuring teams to detect them. One of the sources was a line source, others were point sources (three of them collimated). The radionuclides used in the sources were {sup 60}Co, {sup 137}Cs, {sup 99m}Tc and {sup 192}Ir. The source activities ranged from about 26 MBq (one of the cobalt sources) to 0.56 TBq (iridium). (au).

  8. Analytic model of the stress waves propagation in thin wall tubes, seeking the location of a harmonic point source in its surface

    International Nuclear Information System (INIS)

    Boaratti, Mario Francisco Guerra

    2006-01-01

    Leaks in pressurized tubes generate acoustic waves that propagate through the walls of these tubes, which can be captured by accelerometers or by acoustic emission sensors. The knowledge of how these walls can vibrate, or in another way, how these acoustic waves propagate in this material is fundamental in the detection and localization process of the leak source. In this work an analytic model was implemented, through the motion equations of a cylindrical shell, with the objective to understand the behavior of the tube surface excited by a point source. Since the cylindrical surface has a closed pattern in the circumferential direction, waves that are beginning their trajectory will meet with another that has already completed the turn over the cylindrical shell, in the clockwise direction as well as in the counter clockwise direction, generating constructive and destructive interferences. After enough time of propagation, peaks and valleys in the shell surface are formed, which can be visualized through a graphic representation of the analytic solution created. The theoretical results were proven through measures accomplished in an experimental setup composed of a steel tube finished in sand box, simulating the condition of infinite tube. To determine the location of the point source on the surface, the process of inverse solution was adopted, that is to say, known the signals of the sensor disposed in the tube surface , it is determined through the theoretical model where the source that generated these signals can be. (author)

  9. An optimized inverse modelling method for determining the location and strength of a point source releasing airborne material in urban environment

    Science.gov (United States)

    Efthimiou, George C.; Kovalets, Ivan V.; Venetsanos, Alexandros; Andronopoulos, Spyros; Argyropoulos, Christos D.; Kakosimos, Konstantinos

    2017-12-01

    An improved inverse modelling method to estimate the location and the emission rate of an unknown point stationary source of passive atmospheric pollutant in a complex urban geometry is incorporated in the Computational Fluid Dynamics code ADREA-HF and presented in this paper. The key improvement in relation to the previous version of the method lies in a two-step segregated approach. At first only the source coordinates are analysed using a correlation function of measured and calculated concentrations. In the second step the source rate is identified by minimizing a quadratic cost function. The validation of the new algorithm is performed by simulating the MUST wind tunnel experiment. A grid-independent flow field solution is firstly attained by applying successive refinements of the computational mesh and the final wind flow is validated against the measurements quantitatively and qualitatively. The old and new versions of the source term estimation method are tested on a coarse and a fine mesh. The new method appeared to be more robust, giving satisfactory estimations of source location and emission rate on both grids. The performance of the old version of the method varied between failure and success and appeared to be sensitive to the selection of model error magnitude that needs to be inserted in its quadratic cost function. The performance of the method depends also on the number and the placement of sensors constituting the measurement network. Of significant interest for the practical application of the method in urban settings is the number of concentration sensors required to obtain a ;satisfactory; determination of the source. The probability of obtaining a satisfactory solution - according to specified criteria -by the new method has been assessed as function of the number of sensors that constitute the measurement network.

  10. Location of collinear equilibrium points in the generalised ...

    African Journals Online (AJOL)

    We have discussed the location of collinear equilibrium points in the generalised photogravitational restricted three body problem. The problem is generalised in the sense that both primaries are oblate spheroid. They are source of radiation as well. We have found the solution for the location of collinear point L1. We found ...

  11. A pedagogic JavaScript program for point location strategies

    KAUST Repository

    de Castro, Pedro

    2011-01-01

    Point location in triangulations is a classical problem in computational geometry. And walking in a triangulation is often used as the starting point for several nice point location strategies. We present a pedagogic JavaScript program demonstrating some of these strategies, which is available at: www-sop.inria.fr/geometrica/demo/point location strategies/.

  12. VT US EPA Regulated Facilities Point Locations

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The EnvironPollution_ENVPTS2001 data layer is based on the U.S. EPA's Envirofacts point shapefile. The data was provided to VCGI by the Vermont...

  13. Source Location of Noble Gas Plumes

    International Nuclear Information System (INIS)

    Hoffman, I.; Ungar, K.; Bourgouin, P.; Yee, E.; Wotawa, G.

    2015-01-01

    In radionuclide monitoring, one of the most significant challenges from a verification or surveillance perspective is the source location problem. Modern monitoring/surveillance systems employ meteorological source reconstruction — for example, the Fukushima accident, CRL emissions analysis and even radon risk mapping. These studies usually take weeks to months to conduct, involving multidisciplinary teams representing meteorology; dispersion modelling; radionuclide sampling and metrology; and, when relevant, proper representation of source characteristics (e.g., reactor engineering expertise). Several different approaches have been tried in an attempt to determine useful techniques to apply to the source location problem and to develop rigorous methods that combine all potentially relevant observations and models to identify a most probable source location and size with uncertainties. The ultimate goal is to understand the utility and limitations of these techniques so they can transition from R&D to operational tools. (author)

  14. Optical alignment using the Point Source Microscope

    Science.gov (United States)

    Parks, Robert E.; Kuhn, William P.

    2005-08-01

    We give an example of a Point Source Microscope (PSM) and describe its uses as an aid in the alignment of optical systems including the referencing of optical to mechanical datums. The PSM is a small package (about 100x150x30 mm), including a point source of light, beam splitter, microscope objective and digital CCD camera to detect the reflected light spot. A software package in conjunction with a computer video display locates the return image in three degrees of freedom relative to an electronic spatial reference point. The PSM also includes a Koehler illumination source so it may be used as a portable microscope for ordinary imaging and the microscope can be zoomed under computer control. For added convenience, the laser diode point source can be made quite bright to facilitate initial alignment under typical laboratory lighting conditions. The PSM is particularly useful in aligning optical systems that do not have circular symmetry or are distributed in space such as off-axis systems. The PSM is also useful for referencing the centers of curvatures of optical surfaces to mechanical datums of the structure in which the optics are mounted. By removing the microscope objective the PSM can be used as an electronic autocollimator because of the infinite conjugate optical design.

  15. Calcareous Fens - Source Feature Points

    Data.gov (United States)

    Minnesota Department of Natural Resources — Pursuant to the provisions of Minnesota Statutes, section 103G.223, this database contains points that represent calcareous fens as defined in Minnesota Rules, part...

  16. Locating noise sources with a microphone array

    International Nuclear Information System (INIS)

    Bale, A.; Johnson, D.

    2010-01-01

    Noise pollution is one of the contributors to the public opposition of wind farms. Most of the noise produced by turbines is caused by the aerodynamic interactions between the turbine blades and the surrounding air. This poster presentation discussed a series of aeroacoustic tests conducted to account for the different in vortical structures caused by the rotation of the blades. Microphone arrays were used measure and locate the source of noise. A beam forming technique was used to measure the noise using an algorithm that identified a scanning grid on a plane where the source was thought to be located. It delayed each microphone's signal by the length of time required for the sound to travel from the scan position to each microphone, and accounted for the amplitudes according to the distance from the scan position to each microphone. Demonstration test cases were conducted using piezo buzzers attached to aluminum bars and mounted to the shaft of a DC motor that produced a rotational diameter of 0.95 meter. The buzzers were placed 1 meter from the array. Multiple sound sources at the same frequency were identified, and the moving sources were accurately measured and located. tabs., figs.

  17. Computation of the locus crossing point location of MC circuit

    International Nuclear Information System (INIS)

    Liu Hai-Jun; Li Zhi-Wei; Bu Kai; Sun Zhao-Lin; Nie Hong-Shan

    2014-01-01

    In this paper, the crossing point property of the i–v hysteresis curve in a memristor–capacitor (MC) circuit is analyzed. First, the ideal passive memristor on the crossing point property of i–v hysteresis curve is studied. Based on the analysis, the analytical derivation with respect to the crossing point location of MC circuit is given. Then the example of MC with linear memristance-versus-charge state map is demonstrated to discuss the drift property of cross-point location, caused by the frequency and capacitance value. (interdisciplinary physics and related areas of science and technology)

  18. Tremor Source Location at Okmok Volcano

    Science.gov (United States)

    Reyes, C. G.; McNutt, S. R.

    2007-12-01

    Initial results using an amplitude-based tremor location program have located several active tremor episodes under Cone A, a vent within Okmok volcano's 10 km caldera. Okmok is an andesite volcano occupying the north-eastern half of Umnak Island, in the Aleutian islands. Okmok is defined by a ~2000 y.b.p. caldera that contains multiple cinder cones. Cone A, the youngest of these, extruded lava in 1997 covering the caldera floor. Since April 2003, continuous seismic data have been recorded from eight vertical short-period stations (L4-C's) installed at distances from Cone A ranging from 2 km to 31 km. In 2004 four additional 3- component broadband stations were added, co-located with continuous GPS stations. InSAR and GPS measurements of post-eruption deformation show that Okmok experienced several periods of rapid inflation (Mann and Freymueller, 2002), from the center of the 10 km diameter caldera. While there are few locatable VT earthquakes, there has been nearly continuous low-level tremor with stronger amplitude bursts occurring at variable rates and durations. The character of occurrence remained relatively constant over the course of days to weeks until the signal ceased in mid 2005. Within any day, tremor behavior remains fairly consistent, with bursts closely resembling each other, suggesting a single main process or source location. The tremor is composed of irregular waves with a broad range of frequencies, though most energy resides between ~2 Hz and 6 Hz. Attempts to locate the tremor using traditional arrival time methods fail because the signal is emergent, with envelopes too ragged to correlate on time scales that hold much hope for a location. Instead, focus was shifted to the amplitude ratios at various stations. Candidates for the tremor source include the center of inflation and Cone A, 3 km to the south-west. For all dates on record, data were band pass filtered between 1 and 5 Hz, then evaluated in 20.48 second windows (N=2048, sampling rate

  19. Influence of conversion on the location of points and lines: The change of location entropy and the probability of a vector point inside the converted grid point

    Science.gov (United States)

    Chen, Nan

    2018-03-01

    Conversion of points or lines from vector to grid format, or vice versa, is the first operation required for most spatial analysis. Conversion, however, usually causes the location of points or lines to change, which influences the reliability of the results of spatial analysis or even results in analysis errors. The purpose of this paper is to evaluate the change of the location of points and lines during conversion using the concepts of probability and entropy. This paper shows that when a vector point is converted to a grid point, the vector point may be outside or inside the grid point. This paper deduces a formula for computing the probability that the vector point is inside the grid point. It was found that the probability increased with the side length of the grid and with the variances of the coordinates of the vector point. In addition, the location entropy of points and lines are defined in this paper. Formulae for computing the change of the location entropy during conversion are deduced. The probability mentioned above and the change of location entropy may be used to evaluate the location reliability of points and lines in Geographic Information Systems and may be used to choose an appropriate range of the side length of grids before conversion. The results of this study may help scientists and users to avoid mistakes caused by the change of location during conversion as well as in spatial decision and analysis.

  20. Is a wind turbine a point source? (L).

    Science.gov (United States)

    Makarewicz, Rufin

    2011-02-01

    Measurements show that practically all noise of wind turbine noise is produced by turbine blades, sometimes a few tens of meters long, despite that the model of a point source located at the hub height is commonly used. The plane of rotating blades is the critical location of the receiver because the distances to the blades are the shortest. It is shown that such location requires certain condition to be met. The model is valid far away from the wind turbine as well.

  1. Γ-source Neutral Point Clamped Inverter

    DEFF Research Database (Denmark)

    Mo, Wei; Loh, Poh Chiang; Blaabjerg, Frede

    Transformer based Z-source inverters are recently proposed to achieve promising buck-boost capability. They have improved higher buck-boost capability, smaller size and less components count over Z-source inverters. On the other hand, neutral point clamped inverters have less switching stress...

  2. Methods to identify and locate spent radiation sources

    International Nuclear Information System (INIS)

    1995-07-01

    The objective of this manual is to provide essential guidance to Member States with nuclear applications involving the use of a wide range of sealed radiation sources on the practical task of physically locating spent radiation sources not properly accounted for. Advice is also provided to render the located source safe on location. Refs, figs and tabs

  3. Methods to identify and locate spent radiation sources

    International Nuclear Information System (INIS)

    1997-06-01

    The objective of this manual is to provide essential guidance to Member States with nuclear applications involving the use of a wide range of sealed radiation sources on the practical task of physically locating spent radiation sources not properly accounted for. Advice is also provided to render the located source safe on location. Refs, figs, tabs

  4. Continuous wavelet transform analysis and modal location analysis acoustic emission source location for nuclear piping crack growth monitoring

    International Nuclear Information System (INIS)

    Mohd, Shukri; Holford, Karen M.; Pullin, Rhys

    2014-01-01

    Source location is an important feature of acoustic emission (AE) damage monitoring in nuclear piping. The ability to accurately locate sources can assist in source characterisation and early warning of failure. This paper describe the development of a novelAE source location technique termed 'Wavelet Transform analysis and Modal Location (WTML)' based on Lamb wave theory and time-frequency analysis that can be used for global monitoring of plate like steel structures. Source location was performed on a steel pipe of 1500 mm long and 220 mm outer diameter with nominal thickness of 5 mm under a planar location test setup using H-N sources. The accuracy of the new technique was compared with other AE source location methods such as the time of arrival (TOA) techniqueand DeltaTlocation. Theresults of the study show that the WTML method produces more accurate location resultscompared with TOA and triple point filtering location methods. The accuracy of the WTML approach is comparable with the deltaT location method but requires no initial acoustic calibration of the structure

  5. Isotropic irradiation of detectors from point sources

    DEFF Research Database (Denmark)

    Aage, Helle Karina

    1997-01-01

    NaI(Tl) scintillator detectors have been exposed to gamma rays from 8 different point sources from different directions. Background and backscatter of gamma-rays from the surroundings have been subtracted in order to produce clean spectra. By adding spectra obtained from exposures from different ...

  6. Pseudo-dynamic source modelling with 1-point and 2-point statistics of earthquake source parameters

    KAUST Repository

    Song, S. G.

    2013-12-24

    Ground motion prediction is an essential element in seismic hazard and risk analysis. Empirical ground motion prediction approaches have been widely used in the community, but efficient simulation-based ground motion prediction methods are needed to complement empirical approaches, especially in the regions with limited data constraints. Recently, dynamic rupture modelling has been successfully adopted in physics-based source and ground motion modelling, but it is still computationally demanding and many input parameters are not well constrained by observational data. Pseudo-dynamic source modelling keeps the form of kinematic modelling with its computational efficiency, but also tries to emulate the physics of source process. In this paper, we develop a statistical framework that governs the finite-fault rupture process with 1-point and 2-point statistics of source parameters in order to quantify the variability of finite source models for future scenario events. We test this method by extracting 1-point and 2-point statistics from dynamically derived source models and simulating a number of rupture scenarios, given target 1-point and 2-point statistics. We propose a new rupture model generator for stochastic source modelling with the covariance matrix constructed from target 2-point statistics, that is, auto- and cross-correlations. Our sensitivity analysis of near-source ground motions to 1-point and 2-point statistics of source parameters provides insights into relations between statistical rupture properties and ground motions. We observe that larger standard deviation and stronger correlation produce stronger peak ground motions in general. The proposed new source modelling approach will contribute to understanding the effect of earthquake source on near-source ground motion characteristics in a more quantitative and systematic way.

  7. Development of a Point Pyroshock Source Simulator

    Directory of Open Access Journals (Sweden)

    Ju-won Jeong

    2017-01-01

    Full Text Available We developed a point pyroshock source simulator (PPSS for the study on the source isolation approach (SIA in this study. In spite of the potentiality of the SIA for avionics protection against pyroshock, it has rarely been investigated due to lack of pyroshock source simulators. To overcome such a situation, we proposed the PPSS using a mechanically excited tuned resonator simulating a release device itself. The PPSS was designed using explicit finite element analysis and Seigel’s gas gun model. To verify the proposed PPSS, the prototype was fabricated and tested. From the results, we have shown that the prototype of the PPSS simulates a near-field pyroshock and is able to evaluate the SIA.

  8. Determining Fire Dates and Locating Ignition Points With Satellite Data

    Directory of Open Access Journals (Sweden)

    Akli Benali

    2016-04-01

    Full Text Available Each wildfire has its own “history”, burns under specific conditions and leads to unique environmental impacts. Information on where and when it has started and its duration is important to improve understanding on the dynamics of individual wildfires. This information is typically included in fire databases that are known to have: (i multiple error sources; (ii limited spatial coverage and/or time span, and; (iii often unknown accuracy and uncertainty. Satellite data have a large potential to reduce such limitations. We used active fire data from the MODerate Resolution Imaging Spectroradiometer (MODIS to estimate fire start/end dates and ignition location(s for large wildfires that occurred in Alaska, Portugal, Greece, California and southeastern Australia. We assessed the agreement between satellite-derived estimates and data from fire databases, and determined the associated uncertainty. Fire dates and ignition location(s were estimated for circa 76% of the total burnt area extent for the five study regions. The ability to estimate fire dates and ignitions from satellite data increased with fire size. The agreement between reported and estimated fire dates was very good for start dates (Model efficiency index, MEF = 0.91 and reasonable for end dates (MEF = 0.73. The spatio-temporal agreement between reported and satellite-derived wildfire ignitions showed temporal lags and distances within 12 h and 2 km, respectively. Uncertainties associated with ignition estimates were generally larger than the disagreements with data reported in fire databases. Our results show how satellite data can contribute to improve information regarding dates and ignitions of large wildfires. This contribution can be particularly relevant in regions with scarce fire information, while in well-documented areas it can be used to complement, potentially detect, and correct inconsistencies in existing fire databases. Using data from other existing and/or upcoming

  9. 2011 Radioactive Materials Usage Survey for Unmonitored Point Sources

    Energy Technology Data Exchange (ETDEWEB)

    Sturgeon, Richard W. [Los Alamos National Laboratory

    2012-06-27

    organized. The RMUS Interview Form with the attached RMUS Process Form(s) provides the radioactive materials survey data by technical area (TA) and building number. The survey data for each release point includes information such as: exhaust stack identification number, room number, radioactive material source type (i.e., potential source or future potential source of air emissions), radionuclide, usage (in curies) and usage basis, physical state (gas, liquid, particulate, solid, or custom), release fraction (from Appendix D to 40 CFR 61, Subpart H), and process descriptions. In addition, the interview form also calculates emissions (in curies), lists mrem/Ci factors, calculates PEDEs, and states the location of the critical receptor for that release point. [The critical receptor is the maximum exposed off-site member of the public, specific to each individual facility.] Each of these data fields is described in this section. The Tier classification of release points, which was first introduced with the 1999 usage survey, is also described in detail in this section. Section 4 includes a brief discussion of the dose estimate methodology, and includes a discussion of several release points of particular interest in the CY 2011 usage survey report. It also includes a table of the calculated PEDEs for each release point at its critical receptor. Section 5 describes ES's approach to Quality Assurance (QA) for the usage survey. Satisfactory completion of the survey requires that team members responsible for Rad-NESHAP (National Emissions Standard for Hazardous Air Pollutants) compliance accurately collect and process several types of information, including radioactive materials usage data, process information, and supporting information. They must also perform and document the QA reviews outlined in Section 5.2.6 (Process Verification and Peer Review) of ES-RN, 'Quality Assurance Project Plan for the Rad-NESHAP Compliance Project' to verify that all information is

  10. Sign of Radon for locate geothermic sources

    International Nuclear Information System (INIS)

    Gonzalez Teran, D.

    1991-01-01

    Evaluation of a geothermic field is based upon geological, geophysical and geochemical studies that enable the evaluation of the deposit potential, that is to say, the amount of energy per unit mass, the volume of the trapped fluid, vapor fraction and fluid chemistry. This thesis has as its objective the evaluation of radon gas emanation in high potential geothermic zones in order to utilize the results as a low cost and easy to manage complimentary tool in geothermic source prospection. In chapter I the importance and evaluation of a geothermic deposit is discussed. In chapter II the general characteristics of radon are discussed: its radioactivity and behavior upon diffusion over the earth's surface> Chapter III establishes the approach used in the geothermic field of Los Azufres, Michoacan, to carry out samplings of radon and the laboratory techniques that were used to evaluate the concentration of radon in the subsoil. Finally in chapter IV measurements of radon in the field are compared to geological faults in the area under study. The sampling zones were: low geothermic potential zone of the northern and the southern zone having a greater geothermic potential than that in the north. The study was carried out at different sampling times using plastics detectors of from 30 to 46 days from February to July. From the results obtained we concluded that the emission of radon was greater in the zones of greatest geothermic potential than in the low geothermic potential zones it was also affected by the fault structure and the time of year in which sampling was done. (Author)

  11. A Comparative Study Of Source Location And Depth Estimates From ...

    African Journals Online (AJOL)

    A Comparative Study Of Source Location And Depth Estimates From Total Intensity And Reduced-To-The Pole Magnetic Data. ... Ife Journal of Science ... analysed to show that estimates of source location and depth can be improved significantly by reducing the data to the pole prior to the application of the HGM, ASA and ...

  12. Predicting Locations of Pollution Sources using Convolutional Neural Networks

    OpenAIRE

    Chi, Yiheng; Winovich, Nickolas D.; Lin, Guang

    2017-01-01

    Pollution is a severe problem today, and the main challenge in water and air pollution controls and eliminations is detecting and locating pollution sources. This research project aims to predict the locations of pollution sources given diffusion information of pollution in the form of array or image data. These predictions are done using machine learning. The relations between time, location, and pollution concentration are first formulated as pollution diffusion equations, which are partial...

  13. Search for high energy cosmic neutrino point sources with ANTARES

    International Nuclear Information System (INIS)

    Halladjian, G.

    2010-01-01

    The aim of this thesis is the search for high energy cosmic neutrinos emitted by point sources with the ANTARES neutrino telescope. The detection of high energy cosmic neutrinos can bring answers to important questions such as the origin of cosmic rays and the γ-rays emission processes. In the first part of the thesis, the neutrino flux emitted by galactic and extragalactic sources and the number of events which can be detected by ANTARES are estimated. This study uses the measured γ-ray spectra of known sources taking into account the γ-ray absorption by the extragalactic background light. In the second part of the thesis, the absolute pointing of the ANTARES telescope is evaluated. Being located at a depth of 2475 m in sea water, the orientation of the detector is determined by an acoustic positioning system which relies on low and high frequency acoustic waves measurements between the sea surface and the bottom. The third part of the thesis is a search for neutrino point sources in the ANTARES data. The search algorithm is based on a likelihood ratio maximization method. It is used in two search strategies; 'the candidate sources list strategy' and 'the all sky search strategy'. Analysing 2007+2008 data, no discovery is made and the world's best upper limits on neutrino fluxes from various sources in the Southern sky are established. (author)

  14. Refining FIA plot locations using LiDAR point clouds

    Science.gov (United States)

    Charlie Schrader-Patton; Greg C. Liknes; Demetrios Gatziolis; Brian M. Wing; Mark D. Nelson; Patrick D. Miles; Josh Bixby; Daniel G. Wendt; Dennis Kepler; Abbey. Schaaf

    2015-01-01

    Forest Inventory and Analysis (FIA) plot location coordinate precision is often insufficient for use with high resolution remotely sensed data, thereby limiting the use of these plots for geospatial applications and reducing the validity of models that assume the locations are precise. A practical and efficient method is needed to improve coordinate precision. To...

  15. Radioactive point source localization in a bulky volume

    International Nuclear Information System (INIS)

    Presler, O.; German, U.; Alfassi, Z.B.

    2005-01-01

    When using two detectors to measure the emission of gamma rays from a bulky sample, the count rates ratio of the detectors can be used to locate a radioactive source in a bulky volume. This process may be needed for locating a source in a scrap or waste container. Simple functions for location determination can be developed for the non-absorbing and pure-absorbing media, but for the general case, a more sophisticated method must be used. A simple and practical algorithm was developed, which can predict the location of a point source in a bulk volume quite accurately, with an average possible deviation of up to about 1cm, except for extreme combinations of dimension and absorption coefficient, but also in this case the maximal expected deviations are not more than several centimeters. The algorithm was checked experimentally for several bulk volumes with length of up to about 50cm and with different length/absorption coefficient combinations. The experimental validation was performed for a great range of absorption coefficients (from μ=0.0001 to 0.2cm -1 ), covering the practical range of waste containers compositions

  16. Acoustic wavefield evolution as a function of source location perturbation

    KAUST Repository

    Alkhalifah, Tariq Ali

    2010-12-01

    The wavefield is typically simulated for seismic exploration applications through solving the wave equation for a specific seismic source location. The direct relation between the form (or shape) of the wavefield and the source location can provide insights useful for velocity estimation and interpolation. As a result, I derive partial differential equations that relate changes in the wavefield shape to perturbations in the source location, especially along the Earth\\'s surface. These partial differential equations have the same structure as the wave equation with a source function that depends on the background (original source) wavefield. The similarity in form implies that we can use familiar numerical methods to solve the perturbation equations, including finite difference and downward continuation. In fact, we can use the same Green\\'s function to solve the wave equation and its source perturbations by simply incorporating source functions derived from the background field. The solutions of the perturbation equations represent the coefficients of a Taylor\\'s series type expansion of the wavefield as a function of source location. As a result, we can speed up the wavefield calculation as we approximate the wavefield shape for sources in the vicinity of the original source. The new formula introduces changes to the background wavefield only in the presence of lateral velocity variation or in general terms velocity variations in the perturbation direction. The approach is demonstrated on the smoothed Marmousi model.

  17. Locating CVBEM collocation points for steady state heat transfer problems

    Science.gov (United States)

    Hromadka, T.V.

    1985-01-01

    The Complex Variable Boundary Element Method or CVBEM provides a highly accurate means of developing numerical solutions to steady state two-dimensional heat transfer problems. The numerical approach exactly solves the Laplace equation and satisfies the boundary conditions at specified points on the boundary by means of collocation. The accuracy of the approximation depends upon the nodal point distribution specified by the numerical analyst. In order to develop subsequent, refined approximation functions, four techniques for selecting additional collocation points are presented. The techniques are compared as to the governing theory, representation of the error of approximation on the problem boundary, the computational costs, and the ease of use by the numerical analyst. ?? 1985.

  18. Voltage sag source location based on instantaneous energy detection

    DEFF Research Database (Denmark)

    Chen, Zhe; Xinzhou, Dong; Wei, Kong

    2007-01-01

    Voltage sag is the major power quality problem, which could disrupt the operation of sensitive equipment. This paper presents the applications of instantaneous energy direction for voltage sag source detection. Simulations have been performed to provide the analysis for system with distributed...... generation units. The studies show that the presented method can effectively detect the location of the voltage sag source....

  19. A device for locating acoustic wave emitting sources

    International Nuclear Information System (INIS)

    Andre, J.-L.; Chretien, Nicole; Monier, Jean.

    1973-01-01

    The invention relates to a device for locating acoustic wave emitting sources. A two dimensional sensor network, with diamond-shaped (or the like) meshes, is placed on the surface of a structure in which acoustic wave emitting sources are to be located. The sensors are arranged according to two groups, each of which is connected to a clock and a counter. Every signal fed into a mesh of the network inhibits all the other sensors not belonging to said mesh; the location of the source within the diamond-shaped mesh is achieved by triangulation. This can be applied to the detection of flaws in metal structures, e.g. in nuclear reactor vessels [fr

  20. Scattering and absorption of particles emitted by a point source in a cluster of point scatterers

    International Nuclear Information System (INIS)

    Liljequist, D.

    2012-01-01

    A theory for the scattering and absorption of particles isotropically emitted by a point source in a cluster of point scatterers is described and related to the theory for the scattering of an incident particle beam. The quantum mechanical probability of escape from the cluster in different directions is calculated, as well as the spatial distribution of absorption events within the cluster. A source strength renormalization procedure is required. The average quantum scattering in clusters with randomly shifting scatterer positions is compared to trajectory simulation with the aim of studying the validity of the trajectory method. Differences between the results of the quantum and trajectory methods are found primarily for wavelengths larger than the average distance between nearest neighbour scatterers. The average quantum results include, for example, a local minimum in the number of absorption events at the location of the point source and interference patterns in the angle-dependent escape probability as well as in the distribution of absorption events. The relative error of the trajectory method is in general, though not generally, of similar magnitude as that obtained for beam scattering.

  1. Influence of external source location in the reactivity calculation

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adilson Costa da; Silva, Fernando Carvalho da; Martinez, Aquilino Senra, E-mail: asilva@con.ufrj.b, E-mail: fernando@con.ufrj.b, E-mail: Aquilino@lmp.ufrj.b [Coordenacao dos Programas de Pos-Graduacao de Engenharia (PEN/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear

    2011-07-01

    We used the neutron diffusion equation with external neutron sources, in cartesian geometry and the two groups of energy, to verify the influence of external neutron source locations in the reactivity calculation. For this, a coarse mesh finite difference method was developed for the adjoint flux calculation and simplifies reactivity calculation in PWR type reactor, which uses the output of the nodal expansion method. The results were obtained for different locations on the two-dimensional plane, as well as for different types of fuel elements in the reactor core. (author)

  2. Influence of external source location in the reactivity calculation

    International Nuclear Information System (INIS)

    Silva, Adilson Costa da; Silva, Fernando Carvalho da; Martinez, Aquilino Senra

    2011-01-01

    We used the neutron diffusion equation with external neutron sources, in cartesian geometry and the two groups of energy, to verify the influence of external neutron source locations in the reactivity calculation. For this, a coarse mesh finite difference method was developed for the adjoint flux calculation and simplifies reactivity calculation in PWR type reactor, which uses the output of the nodal expansion method. The results were obtained for different locations on the two-dimensional plane, as well as for different types of fuel elements in the reactor core. (author)

  3. The Central Point Source in G76. 9+ 1.0

    Indian Academy of Sciences (India)

    2016-01-27

    Jan 27, 2016 ... We describe the serendipitous discovery of a very steep-spectrum radio point source in low-frequency Giant Metrewave Radio Telescope (GMRT) images of the supernova remnant (SNR) G76.9+1.0. The steep spectrum, as well as the location of the point source near the centre of this SNR confirm that this ...

  4. Learning to locate an odour source with a mobile robot

    OpenAIRE

    Duckett, T.; Axelsson, M.; Saffiotti, A.

    2001-01-01

    We address the problem of enabling a mobile robot to locate a stationary odour source using an electronic nose constructed from gas sensors. On the hardware side, we use a stereo nose architecture consisting of two parallel chambers, each containing an identical set of sensors. On the software side, we use a recurrent artificial neural network to learn the direction to a stationary source from a time series of sensor readings. This contrasts with previous approaches, that rely on the existenc...

  5. Voltage Sag Source Location Based on Instantaneous Energy Detection

    DEFF Research Database (Denmark)

    Chen, Zhe; Kong, Wei; Dong, Xinzhou

    2008-01-01

    Voltage sag is a major power quality problem, which could disrupt the operation of voltage-sensitive equipment. This paper presents the method based on variation components-based instantaneous energy for voltage sag source detection. Simulations have been performed to provide the thorough analysis...... for system with distributed generation units. The studies show that the presented method can effectively detect the location of voltage sag source....

  6. X-ray Discovery Points to Location of Missing Matter

    Science.gov (United States)

    2010-05-01

    Using observations with NASA's Chandra X-ray Observatory and ESA's XMM-Newton, astronomers have announced a robust detection of a vast reservoir of intergalactic gas about 400 million light years from Earth. This discovery is the strongest evidence yet that the "missing matter" in the nearby Universe is located in an enormous web of hot, diffuse gas. This missing matter — which is different from dark matter -- is composed of baryons, the particles, such as protons and neutrons, that are found on the Earth, in stars, gas, galaxies, and so on. A variety of measurements of distant gas clouds and galaxies have provided a good estimate of the amount of this "normal matter" present when the universe was only a few billion years old. However, an inventory of the much older, nearby universe has turned up only about half as much normal matter, an embarrassingly large shortfall. The mystery then is where does this missing matter reside in the nearby Universe? This latest work supports predictions that it is mostly found in a web of hot, diffuse gas known as the Warm-Hot Intergalactic Medium (WHIM). Scientists think the WHIM is material left over after the formation of galaxies, which was later enriched by elements blown out of galaxies. "Evidence for the WHIM is really difficult to find because this stuff is so diffuse and easy to see right through," said Taotao Fang of the University of California at Irvine and lead author of the latest study. "This differs from many areas of astronomy where we struggle to see through obscuring material." To look for the WHIM, the researchers examined X-ray observations of a rapidly growing supermassive black hole known as an active galactic nucleus, or AGN. This AGN, which is about two billion light years away, generates immense amounts of X-ray light as it pulls matter inwards. Lying along the line of sight to this AGN, at a distance of about 400 million light years, is the so-called Sculptor Wall. This "wall", which is a large diffuse

  7. An inverse source location algorithm for radiation portal monitor applications

    International Nuclear Information System (INIS)

    Miller, Karen A.; Charlton, William S.

    2010-01-01

    Radiation portal monitors are being deployed at border crossings throughout the world to prevent the smuggling of nuclear and radiological materials; however, a tension exists between security and the free-flow of commerce. Delays at ports-of-entry have major economic implications, so it is imperative to minimize portal monitor screening time. We have developed an algorithm to locate a radioactive source using a distributed array of detectors, specifically for use at border crossings. To locate the source, we formulated an optimization problem where the objective function describes the least-squares difference between the actual and predicted detector measurements. The predicted measurements are calculated by solving the 3-D deterministic neutron transport equation given an estimated source position. The source position is updated using the steepest descent method, where the gradient of the objective function with respect to the source position is calculated using adjoint transport calculations. If the objective function is smaller than the convergence criterion, then the source position has been identified. This paper presents the derivation of the underlying equations in the algorithm as well as several computational test cases used to characterize its accuracy.

  8. Autonomous robotic platforms for locating radio sources buried under rubble

    Science.gov (United States)

    Tasu, A. S.; Anchidin, L.; Tamas, R.; Paun, M.; Danisor, A.; Petrescu, T.

    2016-12-01

    This paper deals with the use of autonomous robotic platforms able to locate radio signal sources such as mobile phones, buried under collapsed buildings as a result of earthquakes, natural disasters, terrorism, war, etc. This technique relies on averaging position data resulting from a propagation model implemented on the platform and the data acquired by robotic platforms at the disaster site. That allows us to calculate the approximate position of radio sources buried under the rubble. Based on measurements, a radio map of the disaster site is made, very useful for locating victims and for guiding specific rubble lifting machinery, by assuming that there is a victim next to a mobile device detected by the robotic platform; by knowing the approximate position, the lifting machinery does not risk to further hurt the victims. Moreover, by knowing the positions of the victims, the reaction time is decreased, and the chances of survival for the victims buried under the rubble, are obviously increased.

  9. Towards an accurate real-time locator of infrasonic sources

    Science.gov (United States)

    Pinsky, V.; Blom, P.; Polozov, A.; Marcillo, O.; Arrowsmith, S.; Hofstetter, A.

    2017-11-01

    Infrasonic signals propagate from an atmospheric source via media with stochastic and fast space-varying conditions. Hence, their travel time, the amplitude at sensor recordings and even manifestation in the so-called "shadow zones" are random. Therefore, the traditional least-squares technique for locating infrasonic sources is often not effective, and the problem for the best solution must be formulated in probabilistic terms. Recently, a series of papers has been published about Bayesian Infrasonic Source Localization (BISL) method based on the computation of the posterior probability density function (PPDF) of the source location, as a convolution of a priori probability distribution function (APDF) of the propagation model parameters with likelihood function (LF) of observations. The present study is devoted to the further development of BISL for higher accuracy and stability of the source location results and decreasing of computational load. We critically analyse previous algorithms and propose several new ones. First of all, we describe the general PPDF formulation and demonstrate that this relatively slow algorithm might be among the most accurate algorithms, provided the adequate APDF and LF are used. Then, we suggest using summation instead of integration in a general PPDF calculation for increased robustness, but this leads us to the 3D space-time optimization problem. Two different forms of APDF approximation are considered and applied for the PPDF calculation in our study. One of them is previously suggested, but not yet properly used is the so-called "celerity-range histograms" (CRHs). Another is the outcome from previous findings of linear mean travel time for the four first infrasonic phases in the overlapping consecutive distance ranges. This stochastic model is extended here to the regional distance of 1000 km, and the APDF introduced is the probabilistic form of the junction between this travel time model and range-dependent probability

  10. AE source location by neural networks with arrival time profiles

    Czech Academy of Sciences Publication Activity Database

    Chlada, Milan; Blaháček, Michal; Převorovský, Zdeněk

    2009-01-01

    Roč. 19, č. 2 (2009), s. 4-4 ISSN 1213-3825. [NDT in PROGRESS. 12.11.2009-14.11.2009, Praha] R&D Projects: GA ČR GA101/07/1518; GA ČR GA106/07/1393 Institutional research plan: CEZ:AV0Z20760514 Keywords : acoustic emission * source location * artificial neural networks Subject RIV: BI - Acoustics www.cndt.cz

  11. Statistics of multispacecraft observations of chorus dispersion and source location

    Czech Academy of Sciences Publication Activity Database

    Breneman, A. W.; Kletzing, C. A.; Pickett, J.; Chum, Jaroslav; Santolík, Ondřej

    2009-01-01

    Roč. 114, - (2009), A06202/1-A06202/12 ISSN 0148-0227 R&D Projects: GA AV ČR IAA301120601 Grant - others:NSF(US) 0307319; GA MŠk(CZ) ME 842 Institutional research plan: CEZ:AV0Z30420517 Keywords : chorus dispersion * chorus source location * multispacecraft observations Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 3.082, year: 2009

  12. Locating Microseism Sources Using Spurious Arrivals in Intercontinental Noise Correlations

    Science.gov (United States)

    Retailleau, Lise; Boué, Pierre; Stehly, Laurent; Campillo, Michel

    2017-10-01

    The accuracy of Green's functions retrieved from seismic noise correlations in the microseism frequency band is limited by the uneven distribution of microseism sources at the surface of the Earth. As a result, correlation functions are often biased as compared to the expected Green's functions, and they can include spurious arrivals. These spurious arrivals are seismic arrivals that are visible on the correlation and do not belong to the theoretical impulse response. In this article, we propose to use Rayleigh wave spurious arrivals detected on correlation functions computed between European and United States seismic stations to locate microseism sources in the Atlantic Ocean. We perform a slant stack on a time distance gather of correlations obtained from an array of stations that comprises a regional deployment and a distant station. The arrival times and the apparent slowness of the spurious arrivals lead to the location of their source, which is obtained through a grid search procedure. We discuss improvements in the location through this methodology as compared to classical back projection of microseism energy. This method is interesting because it only requires an array and a distant station on each side of an ocean, conditions that can be met relatively easily.

  13. A robust approach for iterative contaminant source location and release history recovery.

    Science.gov (United States)

    Sun, Alexander Y; Painter, Scott L; Wittmeyer, Gordon W

    2006-12-15

    Contamination source identification is a crucial step in environmental remediation. The exact contaminant source locations and release histories are often unknown due to lack of records and therefore must be identified through inversion. Coupled source location and release history identification is a complex nonlinear optimization problem. Existing strategies for contaminant source identification have important practical limitations. In many studies, analytical solutions for point sources are used; the problem is often formulated and solved via nonlinear optimization; and model uncertainty is seldom considered. In practice, model uncertainty can be significant because of the uncertainty in model structure and parameters, and the error in numerical solutions. An inaccurate model can lead to erroneous inversion of contaminant sources. In this work, a constrained robust least squares (CRLS) estimator is combined with a branch-and-bound global optimization solver for iteratively identifying source release histories and source locations. CRLS is used for source release history recovery and the global optimization solver is used for location search. CRLS is a robust estimator that was developed to incorporate directly a modeler's prior knowledge of model uncertainty and measurement error. The robustness of CRLS is essential for systems that are ill-conditioned. Because of this decoupling, the total solution time can be reduced significantly. Our numerical experiments show that the combination of CRLS with the global optimization solver achieved better performance than the combination of a non-robust estimator, i.e., the nonnegative least squares (NNLS) method, with the same solver.

  14. Wavefield dependency on virtual shifts in the source location

    KAUST Repository

    Alkhalifah, Tariq

    2011-02-14

    The wavefield dependence on a virtual shift in the source location can provide information helpful in velocity estimation and interpolation. However, the second-order partial differential equation (PDE) that relates changes in the wavefield form (or shape) to lateral perturbations in the source location depends explicitly on lateral derivatives of the velocity field. For velocity models that include lateral velocity discontinuities this is problematic as such derivatives in their classical definition do not exist. As a result, I derive perturbation partial differential wave equations that are independent of direct velocity derivatives and thus, provide possibilities for wavefield shape extrapolation in complex media. These PDEs have the same structure as the wave equation with a source function that depends on the background (original source) wavefield. The solutions of the perturbation equations provide the coefficients of a Taylor\\'s series type expansion for the wavefield. The new formulas introduce changes to the background wavefield only in the presence of lateral velocity variation or in general terms velocity variations in the perturbation direction. The accuracy of the representation, as demonstrated on the Marmousi model, is generally good. © 2011 European Association of Geoscientists & Engineers.

  15. Concept for Risk-based Prioritisation of Point Sources

    DEFF Research Database (Denmark)

    Overheu, N.D.; Troldborg, Mads; Tuxen, N.

    2010-01-01

    estimates on a local scale from all the sources, and 3D catchment-scale fate and transport modelling. It handles point sources at various knowledge levels and accounts for uncertainties. The tool estimates the impacts on the water supply in the catchment and provides an overall prioritisation of the sites......A large number of point sources pose a threat to ground water resources. A new tool is presented which enables a uniform and transparent risk assessment and prioritisation of these point sources at the catchment scale. The tool integrates aquifer vulnerability mapping, site-specific mass flux...

  16. Fast randomized point location without preprocessing in two- and three-dimensional Delaunay triangulations

    Energy Technology Data Exchange (ETDEWEB)

    Muecke, E.P.; Saias, I.; Zhu, B.

    1996-05-01

    This paper studies the point location problem in Delaunay triangulations without preprocessing and additional storage. The proposed procedure finds the query point simply by walking through the triangulation, after selecting a good starting point by random sampling. The analysis generalizes and extends a recent result of d = 2 dimensions by proving this procedure to take expected time close to O(n{sup 1/(d+1)}) for point location in Delaunay triangulations of n random points in d = 3 dimensions. Empirical results in both two and three dimensions show that this procedure is efficient in practice.

  17. Analysis of Advantages and Disadvantages of the Location Methods of International Auricular Acupuncture Points.

    Science.gov (United States)

    Rong, Pei-Jing; Zhao, Jing-Jun; Wang, Lei; Zhou, Li-Qun

    2016-01-01

    The international standardization of auricular acupuncture points (AAPs) is an important basis for auricular therapy or auricular diagnosis and treatment. The study on the international standardization of AAPs has gone through a long process, in which the location method is one of the key research projects. There are different points of view in the field of AAPs among experts from different countries or regions. By only analyzing the nine representative location methods, this paper tried to offer a proper location method to locate AAPs. Through analysis of the pros and cons of each location method, the location method applied in the WFAS international standard of AAPs is thoroughly considered as an appropriate method. It is important to keep the right direction during developing an International Organization for Standardization (ISO) international standard of auricular acupuncture points and to improve the research quality of international standardization for AAPs.

  18. Simultaneous head tissue conductivity and EEG source location estimation.

    Science.gov (United States)

    Akalin Acar, Zeynep; Acar, Can E; Makeig, Scott

    2016-01-01

    Accurate electroencephalographic (EEG) source localization requires an electrical head model incorporating accurate geometries and conductivity values for the major head tissues. While consistent conductivity values have been reported for scalp, brain, and cerebrospinal fluid, measured brain-to-skull conductivity ratio (BSCR) estimates have varied between 8 and 80, likely reflecting both inter-subject and measurement method differences. In simulations, mis-estimation of skull conductivity can produce source localization errors as large as 3cm. Here, we describe an iterative gradient-based approach to Simultaneous tissue Conductivity And source Location Estimation (SCALE). The scalp projection maps used by SCALE are obtained from near-dipolar effective EEG sources found by adequate independent component analysis (ICA) decomposition of sufficient high-density EEG data. We applied SCALE to simulated scalp projections of 15cm(2)-scale cortical patch sources in an MR image-based electrical head model with simulated BSCR of 30. Initialized either with a BSCR of 80 or 20, SCALE estimated BSCR as 32.6. In Adaptive Mixture ICA (AMICA) decompositions of (45-min, 128-channel) EEG data from two young adults we identified sets of 13 independent components having near-dipolar scalp maps compatible with a single cortical source patch. Again initialized with either BSCR 80 or 25, SCALE gave BSCR estimates of 34 and 54 for the two subjects respectively. The ability to accurately estimate skull conductivity non-invasively from any well-recorded EEG data in combination with a stable and non-invasively acquired MR imaging-derived electrical head model could remove a critical barrier to using EEG as a sub-cm(2)-scale accurate 3-D functional cortical imaging modality. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. The Spectral Statistical Method for Determining the Location Parameters of a Dipole Source of Electromagnetic Radiation

    Science.gov (United States)

    Panyukov, A. V.; Bogushov, A. K.

    2016-09-01

    Using the measured horizontal and vertical components of the magnetic and electric fields, respectively, we solve the problem of determining the location of a dipole source of electromagnetic radiation, which is equivalent to the lightning discharge, at the specified point of an infinitely conducting plane. The proposed method, which is based on the analysis of the measured-signal spectra, allows one to develop many estimates of the source location, choose the final estimate on the basis of the results of analysis of the entire totality of these estimates, and, therefore, reach stability in determining the source location. The spectral method makes it possible to obtain more stable solutions at a lower computation cost compared with the previously developed parametric extremum method. The spectral-method algorithm can be naturally parallelized. The results of the analytical and numerical studies of the accuracy and stability of the proposed method are presented.

  20. Study of Coal Burst Source Locations in the Velenje Colliery

    Directory of Open Access Journals (Sweden)

    Goran Vižintin

    2016-06-01

    Full Text Available The Velenje coal mine (VCM is situated on the largest Slovenian coal deposit and in one of the thickest layers of coal known in the world. The thickness of the coal layer causes problems for the efficiency of extraction, since the majority of mining operations is within the coal layer. The selected longwall coal mining method with specific geometry, increasing depth of excavations, changes in stress state and naturally given geomechanical properties of rocks induce seismic events. Induced seismic events can be caused by caving processes, blasting or bursts of coal or the surrounding rock. For 2.5D visualization, data of excavations, ash content and calorific value of coal samples, hanging wall and footwall occurrence, subsidence of the surface and coal burst source locations were collected. Data and interpolation methods available in software package Surfer®12 were statistically analyzed and a Kriging (KRG interpolation method was chosen. As a result 2.5D visualizations of coal bursts source locations with geomechanical properties of coal samples taken at different depth in the coal seam in the VCM were made with data-visualization packages Surfer®12 and Voxler®3.

  1. The resolution of point sources of light as analyzed by quantum detection theory

    Science.gov (United States)

    Helstrom, C. W.

    1972-01-01

    The resolvability of point sources of incoherent light is analyzed by quantum detection theory in terms of two hypothesis-testing problems. In the first, the observer must decide whether there are two sources of equal radiant power at given locations, or whether there is only one source of twice the power located midway between them. In the second problem, either one, but not both, of two point sources is radiating, and the observer must decide which it is. The decisions are based on optimum processing of the electromagnetic field at the aperture of an optical instrument. In both problems the density operators of the field under the two hypotheses do not commute. The error probabilities, determined as functions of the separation of the points and the mean number of received photons, characterize the ultimate resolvability of the sources.

  2. Resolution of point sources of light as analyzed by quantum detection theory.

    Science.gov (United States)

    Helstrom, C. W.

    1973-01-01

    The resolvability of point sources of incoherent thermal light is analyzed by quantum detection theory in terms of two hypothesis-testing problems. In the first, the observer must decide whether there are two sources of equal radiant power at given locations, or whether there is only one source of twice the power located midway between them. In the second problem, either one, but not both, of two point sources is radiating, and the observer must decide which it is. The decisions are based on optimum processing of the electromagnetic field at the aperture of an optical instrument. In both problems the density operators of the field under the two hypotheses do not commute. The error probabilities, determined as functions of the separation of the points and the mean number of received photons, characterize the ultimate resolvability of the sources.

  3. Sensitivity of Coastal Environments and Wildlife to Spilled Oil: Central California: ALERTS (Vulnerable Resource Location Points)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains vector points representing locations in Central California that should be highlighted for protection due to the presence of certain highly...

  4. Effects of ventilation strategies and source locations on indoor particle deposition

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Ke; Yang, Xiufeng; Kang, Yanming [School of Environmental Science and Engineering, Donghua University, 2999 North Renmin Road, Shanghai 201620 (China)

    2010-03-15

    A computer model for predicting aerosol dispersion in indoor spaces was validated with experimental data found in the literature. The validated model was used to explore the effect of the area or point source locations on aerosol particle transportation in ventilation rooms with rough surfaces. Two different ventilation strategies were studied: mixing ventilation (MV) and underfloor air distribution (UFAD) system. The simulation results show that in MV, the particle concentration and removal effectiveness are little dependent on the position of the pollutant sources. In UFAD, the source location has a strong impact on the distribution and removing of the contaminants. The particle removal performance strongly depends on the ventilation efficiency and the particle deposition loss in the room with rough surfaces. The important consideration in both the relative ventilation efficiency and the deposition rate is the relative position of the sources to the main airflow and the occupied zone in an UFAD room. (author)

  5. An FBG acoustic emission source locating system based on PHAT and GA

    Science.gov (United States)

    Shen, Jing-shi; Zeng, Xiao-dong; Li, Wei; Jiang, Ming-shun

    2017-09-01

    Using the acoustic emission locating technology to monitor the health of the structure is important for ensuring the continuous and healthy operation of the complex engineering structures and large mechanical equipment. In this paper, four fiber Bragg grating (FBG) sensors are used to establish the sensor array to locate the acoustic emission source. Firstly, the nonlinear locating equations are established based on the principle of acoustic emission, and the solution of these equations is transformed into an optimization problem. Secondly, time difference extraction algorithm based on the phase transform (PHAT) weighted generalized cross correlation provides the necessary conditions for the accurate localization. Finally, the genetic algorithm (GA) is used to solve the optimization model. In this paper, twenty points are tested in the marble plate surface, and the results show that the absolute locating error is within the range of 10 mm, which proves the accuracy of this locating method.

  6. Pulsewidth-modulated 2-source neutral-point-clamped inverter

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Loh, Poh Chang; Gao, Feng

    2007-01-01

    This paper presents the careful integration of a newly proposed Z-source topological concept to the basic neutral-point-clamped (NPC) inverter topology for designing a three-level inverter with both voltage-buck and voltage-boost capabilities. The designed Z-source NPC inverter uses two unique X-...

  7. Trans-Z-source Neutral Point Clamped inverter

    DEFF Research Database (Denmark)

    Mo, W.; Loh, P. C.; Li, D.

    2012-01-01

    for buck-boost energy conversion with all the favourable advantages of multi-level switching retained. This paper presents three-level trans-Z-source Neutral Point Clamped (NPC) inverter topology, which achieves both the advantages of trans-Z-source and three-level NPC inverter configuration. With proper...

  8. INHOMOGENEITY IN SPATIAL COX POINT PROCESSES – LOCATION DEPENDENT THINNING IS NOT THE ONLY OPTION

    Directory of Open Access Journals (Sweden)

    Michaela Prokešová

    2010-11-01

    Full Text Available In the literature on point processes the by far most popular option for introducing inhomogeneity into a point process model is the location dependent thinning (resulting in a second-order intensity-reweighted stationary point process. This produces a very tractable model and there are several fast estimation procedures available. Nevertheless, this model dilutes the interaction (or the geometrical structure of the original homogeneous model in a special way. When concerning the Markov point processes several alternative inhomogeneous models were suggested and investigated in the literature. But it is not so for the Cox point processes, the canonical models for clustered point patterns. In the contribution we discuss several other options how to define inhomogeneous Cox point process models that result in point patterns with different types of geometric structure. We further investigate the possible parameter estimation procedures for such models.

  9. Induced Temporal Signatures for Point-Source Detection

    International Nuclear Information System (INIS)

    Stephens, Daniel L.; Runkle, Robert C.; Carlson, Deborah K.; Peurrung, Anthony J.; Seifert, Allen; Wyatt, Cory R.

    2005-01-01

    Detection of radioactive point-sized sources is inherently divided into two regimes encompassing stationary and moving detectors. The two cases differ in their treatment of background radiation and its influence on detection sensitivity. In the stationary detector case the statistical fluctuation of the background determines the minimum detectable quantity. In the moving detector case the detector may be subjected to widely and irregularly varying background radiation, as a result of geographical and environmental variation. This significant systematic variation, in conjunction with the statistical variation of the background, requires a conservative threshold to be selected to yield the same false-positive rate as the stationary detection case. This results in lost detection sensitivity for real sources. This work focuses on a simple and practical modification of the detector geometry that increase point-source recognition via a distinctive temporal signature. A key part of this effort is the integrated development of both detector geometries that induce a highly distinctive signature for point sources and the development of statistical algorithms able to optimize detection of this signature amidst varying background. The identification of temporal signatures for point sources has been demonstrated and compared with the canonical method showing good results. This work demonstrates that temporal signatures are efficient at increasing point-source discrimination in a moving detector system

  10. Source location of chorus emissions observed by Cluster

    Directory of Open Access Journals (Sweden)

    M. Parrot

    Full Text Available One of the objectives of the Cluster mission is to study sources of various electromagnetic waves using the four satellites. This paper describes the methods we have applied to data recorded from the STAFF spectrum analyser. This instrument provides the cross spectral matrix of three magnetic and two electric field components. This spectral matrix is analysed to determine, for each satellite, the direction of the wave normal relative to the Earth’s magnetic field as a function of frequency and of time. Due to the Cluster orbit, chorus emissions are often observed close to perigee, and the data analysis determines the direction of these waves. Three events observed during different levels of magnetic activity are reported. It is shown that the component of the Poynting vector parallel to the magnetic field changes its sense when the satellites cross the magnetic equator, which indicates that the chorus waves propagate away from the equator. Detailed analysis indicates that the source is located in close vicinity of the plane of the geomagnetic equator.

    Key words. Magnetospheric physics (plasma waves and instabilities; storms and substorms; Space plasma physics (waves and instabilities

  11. Chemometric Analysis for Pollution Source Assessment of Harbour Sediments in Arctic Locations

    DEFF Research Database (Denmark)

    Pedersen, Kristine B.; Lejon, Tore; Jensen, Pernille Erland

    2015-01-01

    Pollution levels, pollutant distribution and potential source assessments based on multivariate analysis (chemometrics) were made for harbour sediments from two Arctic locations; Hammerfest in Norway and Sisimiut in Greenland. High levels of heavy metals were detected in addition to organic...... pollutants. Preliminary assessments based on principal component analysis (PCA) revealed different sources and pollutant distribution in the sediments of the two harbours. Tributyltin (TBT) was, however, found to originate from point source(s), and the highest concentrations of TBT in both harbours were...... indicated relation primarily to German, Russian and American mixtures in Hammerfest; and American, Russian and Japanese mixtures in Sisimiut. PCA was shown to be an important tool for identifying pollutant sources and differences in pollutant composition in relation to sediment characteristics....

  12. The distribution of infrared point sources in nearby elliptical galaxies

    Science.gov (United States)

    Gogoi, Rupjyoti; Shalima, P.; Misra, Ranjeev

    2018-02-01

    Infrared (IR) point sources as observed by Spitzer, in nearby early-type galaxies should either be bright sources in the galaxy such as globular clusters, or they may be background sources such as AGNs. These objects are often counterparts of sources in other wavebands such as optical and X-rays and the IR information provides crucial information regarding their nature. However, many of the IR sources may be background objects and it is important to identify them or at least quantify the level of background contamination. Moreover, the distribution of these IR point sources in flux, distance from the centre and colour would be useful in understanding their origin. Archival Spitzer IRAC images provide a unique opportunity for such a study and here we present the results of such an analysis for four nearby galaxies, NGC 1399, NGC 2768, NGC 4365 and NGC 4649. We estimate the background contamination using several blank fields. Our results suggest that IR colours can be effectively used to differentiate between sources in the galaxy and background ones. In particular we find that sources having AGN like colours are indeed consistent with being background AGNs. For sources with non AGN like colours we compute the distribution of flux and normalised distance from the centre which is found to be of a power-law form. Although our sample size is small, the power-law index for the galaxies are different indicating perhaps that the galaxy environment may be playing a part in their origin and nature.

  13. Successful cuing of gender source memory does not improve location source memory.

    Science.gov (United States)

    Hicks, Jason L; Starns, Jeffrey J

    2016-05-01

    In three experiments we explored cross-dimensional cuing effects in a multidimensional source encoding and retrieval paradigm. We employed a bias-controlled experimental method of source cuing at retrieval (Starns & Hicks, 2013) in an attempt to improve retrieval of location information indirectly by cuing gender information. Encoded words were situated on the left or right side of a computer monitor and associated with either a male or a female face. When multiple faces were used across the set of encoded words, reinstating the correct face at retrieval alongside an incorrect, opposite-gender face cue improved male/female source decisions for test words. However, this powerful test cue did not improve memory for the encoded location of the words, suggesting that within-dimension cuing does not produce cross-dimensional cuing. This null outcome was found when gender decisions were required (Experiments 1A and 2) or not required (Experiment 1B) prior to location decisions. Nor was cross-dimension cuing found when subjects were told to expect a source test of both gender and location information at retrieval (Experiment 2). Our findings reinforce prior work demonstrating that multiple context dimensions can be bound to item information without any direct binding between the contexts.

  14. Location Authentication based on Wireless Access Point Information to Prevent Wormhole Attack in Samsung Pay

    Directory of Open Access Journals (Sweden)

    RYU, G.

    2017-08-01

    Full Text Available This paper proposes a location authentication method to prevent wormhole payment attack in Samsung Pay. The primary feature of this method is comparing wireless Access Point (AP information collected by the current Samsung Pay user and a wireless AP model (WM that was created from wireless AP information (WI sent by previous Samsung Pay users. To create the WM, an autoencoder is used. Unlike the existing location authentication techniques that use WI, our method does not require additional hardware, modification of the Point of Sale (POS software, or any pre-requisite information such as the location coordinates of the POS. We show that the proposed location authentication technique exhibits the minimum Equal Error Rate (EER of 2.4% in real payment environments.

  15. On the point-source approximation of earthquake dynamics

    Directory of Open Access Journals (Sweden)

    Andrea Bizzarri

    2014-06-01

    Full Text Available The focus on the present study is on the point-source approximation of a seismic source. First, we compare the synthetic motions on the free surface resulting from different analytical evolutions of the seismic source (the Gabor signal (G, the Bouchon ramp (B, the Cotton and Campillo ramp (CC, the Yoffe function (Y and the Liu and Archuleta function (LA. Our numerical experiments indicate that the CC and the Y functions produce synthetics with larger oscillations and correspondingly they have a higher frequency content. Moreover, the CC and the Y functions tend to produce higher peaks in the ground velocity (roughly of a factor of two. We have also found that the falloff at high frequencies is quite different: it roughly follows ω−2 in the case of G and LA functions, it decays more faster than ω−2 for the B function, while it is slow than ω−1 for both the CC and the Y solutions. Then we perform a comparison of seismic waves resulting from 3-D extended ruptures (both supershear and subshear obeying to different governing laws against those from a single point-source having the same features. It is shown that the point-source models tend to overestimate the ground motions and that they completely miss the Mach fronts emerging from the supershear transition process. When we compare the extended fault solutions against a multiple point-sources model the agreement becomes more significant, although relevant discrepancies still persist. Our results confirm that, and more importantly quantify how, the point-source approximation is unable to adequately describe the radiation emitted during a real world earthquake, even in the most idealized case of planar fault with homogeneous properties and embedded in a homogeneous, perfectly elastic medium.

  16. Localization of Point Sources for Poisson Equation using State Observers

    KAUST Repository

    Majeed, Muhammad Usman

    2016-08-09

    A method based On iterative observer design is presented to solve point source localization problem for Poisson equation with riven boundary data. The procedure involves solution of multiple boundary estimation sub problems using the available Dirichlet and Neumann data from different parts of the boundary. A weighted sum of these solution profiles of sub-problems localizes point sources inside the domain. Method to compute these weights is also provided. Numerical results are presented using finite differences in a rectangular domain. (C) 2016, IFAC (International Federation of Automatic Control) Hosting by Elsevier Ltd. All rights reserved.

  17. Reconstruction analysis of the IRAS Point Source Catalog Redshift Survey

    NARCIS (Netherlands)

    Narayanan, VK; Weinberg, DH; Branchini, E; Frenk, CS; Maddox, S; Oliver, S; Rowan-Robinson, M; Saunders, W

    We present the results of reconstruction analysis of the galaxy distribution in a spherical region of radius 50 h(-1) Mpc centered on the Local Group, as mapped by the IRAS Point Source Catalog Redshift Survey (PSCz). We reconstruct this galaxy distribution using 15 different models for structure

  18. Effect of point source and heterogeneity on the propagation of ...

    African Journals Online (AJOL)

    user

    This paper stands to investigate the possibility of propagation of SH waves due to a point source in a magnetoelastic monoclinic layer lying over a heterogeneous monoclinic half-space. The heterogeneity is caused by consideration of quadratic variation in rigidity. The methodology employed combines an efficient ...

  19. A Search for Point Sources of EeV Photons

    NARCIS (Netherlands)

    Aab, A.; Abreu, P.; Aglietta, M.; Ahlers, M.; Ahn, E. J.; Samarai, I. Al; Albuquerque, I. F. M.; Allekotte, I.; Allen, J.; Allison, P.; Almela, A.; Alvarez Castillo, J.; Alvarez-Muñiz, J.; Alves Batista, R.; Ambrosio, M.; Aminaei, A.; Anchordoqui, L.; Andringa, S.; Aramo, C.; Arqueros, F.; Asorey, H.; Assis, P.; Aublin, J.; Ave, M.; Avenier, M.; Avila, G.; Badescu, A. M.; Barber, K. B.; Bäuml, J.; Baus, C.; Beatty, J. J.; Becker, K. H.; Bellido, J. A.; Berat, C.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanco, F.; Blanco, M.; Bleve, C.; Blümer, H.; Boháčová, M.; Boncioli, D.; Bonifazi, C.; Bonino, R.; Borodai, N.; Brack, J.; Brancus, I.; Brogueira, P.; Brown, W. C.; Buchholz, P.; Bueno, A.; Buscemi, M.; Caballero-Mora, K. S.; Caccianiga, B.; Caccianiga, L.; Candusso, M.; Caramete, L.; Caruso, R.; Castellina, A.; Cataldi, G.; Cazon, L.; Cester, R.; Chavez, A. G.; Cheng, S. H.; Chiavassa, A.; Chinellato, J. A.; Chudoba, J.; Cilmo, M.; Clay, R. W.; Cocciolo, G.; Colalillo, R.; Collica, L.; Coluccia, M. R.; Conceição, R.; Contreras, F.; Cooper, M. J.; Coutu, S.; Covault, C. E.; Criss, A.; Cronin, J.; Curutiu, A.; Dallier, R.; Daniel, B.; Dasso, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; De Domenico, M.; de Jong, S. J.; de Mello Neto, J. R. T.; De Mitri, I.; de Oliveira, J.; de Souza, V.; del Peral, L.; Deligny, O.; Dembinski, H.; Dhital, N.; Di Giulio, C.; Di Matteo, A.; Diaz, J. C.; Díaz Castro, M. L.; Diep, P. N.; Diogo, F.; Dobrigkeit, C.; Docters, W.; D'Olivo, J. C.; Dong, P. N.; Dorofeev, A.; Dorosti Hasankiadeh, Q.; Dova, M. T.; Ebr, J.; Engel, R.; Erdmann, M.; Erfani, M.; Escobar, C. O.; Espadanal, J.; Etchegoyen, A.; Facal San Luis, P.; Falcke, H.; Fang, K.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferguson, A. P.; Fernandes, M.; Fick, B.; Figueira, J. M.; Filevich, A.; Filipčič, A.; Fox, B. D.; Fratu, O.; Fröhlich, U.; Fuchs, B.; Fuji, T.; Gaior, R.; García, B.; Garcia Roca, S. T.; Garcia-Gamez, D.; Garcia-Pinto, D.; Garilli, G.; Gascon Bravo, A.; Gate, F.; Gemmeke, H.; Ghia, P. L.; Giaccari, U.; Giammarchi, M.; Giller, M.; Glaser, C.; Glass, H.; Gomez Albarracin, F.; Gómez Berisso, M.; Gómez Vitale, P. F.; Gonçalves, P.; Gonzalez, J. G.; Gookin, B.; Gorgi, A.; Gorham, P.; Gouffon, P.; Grebe, S.; Griffith, N.; Grillo, A. F.; Grubb, T. D.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Hansen, P.; Harari, D.; Harrison, T. A.; Harton, J. L.; Haungs, A.; Hebbeker, T.; Heck, D.; Heimann, P.; Herve, A. E.; Hill, G. C.; Hojvat, C.; Hollon, N.; Holt, E.; Homola, P.; Hörandel, J. R.; Horvath, P.; Hrabovský, M.; Huber, D.; Huege, T.; Insolia, A.; Isar, P. G.; Islo, K.; Jandt, I.; Jansen, S.; Jarne, C.; Josebachuili, M.; Kääpä, A.; Kambeitz, O.; Kampert, K. H.; Kasper, P.; Katkov, I.; Kégl, B.; Keilhauer, B.; Keivani, A.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Krause, R.; Krohm, N.; Krömer, O.; Kruppke-Hansen, D.; Kuempel, D.; Kunka, N.; La Rosa, G.; LaHurd, D.; Latronico, L.; Lauer, R.; Lauscher, M.; Lautridou, P.; Le Coz, S.; Leão, M. S. A. B.; Lebrun, D.; Lebrun, P.; Leigui de Oliveira, M. A.; Letessier-Selvon, A.; Lhenry-Yvon, I.; Link, K.; López, R.; Lopez Agüera, A.; Louedec, K.; Lozano Bahilo, J.; Lu, L.; Lucero, A.; Ludwig, M.; Lyberis, H.; Maccarone, M. C.; Malacari, M.; Maldera, S.; Maller, J.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Marin, V.; Mariş, I. C.; Marsella, G.; Martello, D.; Martin, L.; Martinez, H.; Martínez Bravo, O.; Martraire, D.; Masías Meza, J. J.; Mathes, H. J.; Mathys, S.; Matthews, A. J.; Matthews, J.; Matthiae, G.; Maurel, D.; Maurizio, D.; Mayotte, E.; Mazur, P. O.; Medina, C.; Medina-Tanco, G.; Melissas, M.; Melo, D.; Menichetti, E.; Menshikov, A.; Messina, S.; Meyhandan, R.; Mićanović, S.; Micheletti, M. I.; Middendorf, L.; Minaya, I. A.; Miramonti, L.; Mitrica, B.; Molina-Bueno, L.; Mollerach, S.; Monasor, M.; Monnier Ragaigne, D.; Montanet, F.; Morello, C.; Moreno, J. C.; Mostafá, M.; Moura, C. A.; Muller, M. A.; Müller, G.; Münchmeyer, M.; Mussa, R.; Navarra, G.; Navas, S.; Necesal, P.; Nellen, L.; Nelles, A.; Neuser, J.; Niechciol, M.; Niemietz, L.; Niggemann, T.; Nitz, D.; Nosek, D.; Novotny, V.; Nožka, L.; Ochilo, L.; Olinto, A.; Oliveira, M.; Ortiz, M.; Pacheco, N.; Pakk Selmi-Dei, D.; Palatka, M.; Pallotta, J.; Palmieri, N.; Papenbreer, P.; Parente, G.; Parra, A.; Pastor, S.; Paul, T.; Pech, M.; Pe¸kala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petermann, E.; Peters, C.; Petrera, S.; Petrolini, A.; Petrov, Y.; Piegaia, R.; Pierog, T.; Pieroni, P.; Pimenta, M.; Pirronello, V.; Platino, M.; Plum, M.; Porcelli, A.; Porowski, C.; Privitera, P.; Prouza, M.; Purrello, V.; Quel, E. J.; Querchfeld, S.; Quinn, S.; Rautenberg, J.; Ravel, O.; Ravignani, D.; Revenu, B.; Ridky, J.; Riggi, S.; Risse, M.; Ristori, P.; Rizi, V.; Roberts, J.; Rodrigues de Carvalho, W.; Rodriguez Cabo, I.; Rodriguez Fernandez, G.; Rodriguez Rojo, J.; Rodríguez-Frías, M. D.; Ros, G.; Rosado, J.; Rossler, T.; Roth, M.; Roulet, E.; Rovero, A. C.; Rühle, C.; Saffi, S. J.; Saftoiu, A.; Salamida, F.; Salazar, H.; Salesa Greus, F.; Salina, G.; Sánchez, F.; Sanchez-Lucas, P.; Santo, C. E.; Santos, E.; Santos, E. M.; Sarazin, F.; Sarkar, B.; Sarmento, R.; Sato, R.; Scharf, N.; Scherini, V.; Schieler, H.; Schiffer, P.; Schmidt, A.; Scholten, O.; Schoorlemmer, H.; Schovánek, P.; Schulz, A.; Schulz, J.; Sciutto, S. J.; Segreto, A.; Settimo, M.; Shadkam, A.; Shellard, R. C.; Sidelnik, I.; Sigl, G.; Sima, O.; Śmiałkowski, A.; Šmída, R.; Snow, G. R.; Sommers, P.; Sorokin, J.; Squartini, R.; Srivastava, Y. N.; Stanič, S.; Stapleton, J.; Stasielak, J.; Stephan, M.; Stutz, A.; Suarez, F.; Suomijärvi, T.; Supanitsky, A. D.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Szuba, M.; Taborda, O. A.; Tapia, A.; Tartare, M.; Thao, N. T.; Theodoro, V. M.; Tiffenberg, J.; Timmermans, C.; Todero Peixoto, C. J.; Toma, G.; Tomankova, L.; Tomé, B.; Tonachini, A.; Torralba Elipe, G.; Torres Machado, D.; Travnicek, P.; Trovato, E.; Tueros, M.; Ulrich, R.; Unger, M.; Urban, M.; Valdés Galicia, J. F.; Valiño, I.; Valore, L.; van Aar, G.; van den Berg, A. M.; van Velzen, S.; van Vliet, A.; Varela, E.; Vargas Cárdenas, B.; Varner, G.; Vázquez, J. R.; Vázquez, R. A.; Veberič, D.; Verzi, V.; Vicha, J.; Videla, M.; Villaseñor, L.; Vlcek, B.; Vorobiov, S.; Wahlberg, H.; Wainberg, O.; Walz, D.; Watson, A. A.; Weber, M.; Weidenhaupt, K.; Weindl, A.; Werner, F.; Whelan, B. J.; Widom, A.; Wiencke, L.; Wilczyńska, B.; Wilczyński, H.; Will, M.; Williams, C.; Winchen, T.; Wittkowski, D.; Wundheiler, B.; Wykes, S.; Yamamoto, T.; Yapici, T.; Younk, P.; Yuan, G.; Yushkov, A.; Zamorano, B.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Zhou, J.; Zhu, Y.; Zimbres Silva, M.; Ziolkowski, M.; Auger Collaboration102, The Pierre

    2014-01-01

    Measurements of air showers made using the hybrid technique developed with the fluorescence and surface detectors of the Pierre Auger Observatory allow a sensitive search for point sources of EeV photons anywhere in the exposed sky. A multivariate analysis reduces the background of hadronic cosmic

  20. Assessment of the impact of point source pollution from the ...

    African Journals Online (AJOL)

    KSTP), was assessed in terms of pH, conductivity, and COD and nutrients removal from the influent. The contributions from this and other smaller point sources in the town to these parameters in the receiving Keiskamma River were determined by ...

  1. Determining and modeling the dispersion of non point source ...

    African Journals Online (AJOL)

    EJIRO

    Lake Victoria is an important source of livelihood that is threatened by rising pollution. In this study, pollutants in runoff are characterized and their dispersion after they enter the lake is measured and modeled at different points in the study areas. The objective is to develop a one dimensional mathematical model which can ...

  2. Effects of Perturbations on the Location of Collinear Points In The ...

    African Journals Online (AJOL)

    In this paper, the effect of small perturbations in the coriolis and the centrifugal forces on the location of collinear points in the restricted three-body problem has been examined when both primaries are triaxial rigid bodies with one of the axes as the axis of symmetry and its equatorial plane coinciding with the plane of ...

  3. Design of sampling locations for river water quality monitoring considering seasonal variation of point and diffuse pollution loads.

    Science.gov (United States)

    Varekar, Vikas; Karmakar, Subhankar; Jha, Ramakar; Ghosh, N C

    2015-06-01

    The design of a water quality monitoring network (WQMN) is a complicated decision-making process because each sampling involves high installation, operational, and maintenance costs. Therefore, data with the highest information content should be collected. The effect of seasonal variation in point and diffuse pollution loadings on river water quality may have a significant impact on the optimal selection of sampling locations, but this possible effect has never been addressed in the evaluation and design of monitoring networks. The present study proposes a systematic approach for siting an optimal number and location of river water quality sampling stations based on seasonal or monsoonal variations in both point and diffuse pollution loadings. The proposed approach conceptualizes water quality monitoring as a two-stage process; the first stage of which is to consider all potential water quality sampling sites, selected based on the existing guidelines or frameworks, and the locations of both point and diffuse pollution sources. The monitoring at all sampling sites thus identified should be continued for an adequate period of time to account for the effect of the monsoon season. In the second stage, the monitoring network is then designed separately for monsoon and non-monsoon periods by optimizing the number and locations of sampling sites, using a modified Sanders approach. The impacts of human interventions on the design of the sampling net are quantified geospatially by estimating diffuse pollution loads and verified with land use map. To demonstrate the proposed methodology, the Kali River basin in the western Uttar Pradesh state of India was selected as a study area. The final design suggests consequential pre- and post-monsoonal changes in the location and priority of water quality monitoring stations based on the seasonal variation of point and diffuse pollution loadings.

  4. Transient point source analyses in the ANTARES neutrino telescope

    Energy Technology Data Exchange (ETDEWEB)

    Sánchez Losa, Agustín, E-mail: Agustin.Sanchez@ific.uv.es

    2014-04-01

    The ANTARES telescope, with a duty cycle close to unity and a full hemisphere of the sky at all the times visible, is well suited to detect neutrinos produced in astrophysical transient sources. Assuming a known neutrino production period, the background and the sensitivity can be drastically improved by selecting a narrow time window around it. GRBs, μ-quasars and AGNs are particularly attractive potential neutrino point sources since neutrinos and gamma-rays may be produced in hadronic interactions with the surrounding medium as they are the most likely sources of the observed ultra high energy cosmic rays. A strong correlation between the gamma-ray and the neutrino fluxes is expected in this scenario. ANTARES data has been analyzed in various transient source analyses with the goal of detecting cosmic neutrinos from GRBs, μ-quasars and AGNs. The sensitivity of a standard time-integrated point source search can be improved by a factor 2–3 by looking for neutrinos only during the most probable emission time. This information can be provided by the different satellite telescope types on the X-rays and γ-rays wavelengths. The results of these different analyses will be presented.

  5. Point sources and multipoles in inverse scattering theory

    CERN Document Server

    Potthast, Roland

    2001-01-01

    Over the last twenty years, the growing availability of computing power has had an enormous impact on the classical fields of direct and inverse scattering. The study of inverse scattering, in particular, has developed rapidly with the ability to perform computational simulations of scattering processes and led to remarkable advances in a range of applications, from medical imaging and radar to remote sensing and seismic exploration. Point Sources and Multipoles in Inverse Scattering Theory provides a survey of recent developments in inverse acoustic and electromagnetic scattering theory. Focusing on methods developed over the last six years by Colton, Kirsch, and the author, this treatment uses point sources combined with several far-reaching techniques to obtain qualitative reconstruction methods. The author addresses questions of uniqueness, stability, and reconstructions for both two-and three-dimensional problems.With interest in extracting information about an object through scattered waves at an all-ti...

  6. Apparatus and method for locating and quantifying or directing a source of ionizing radiation

    International Nuclear Information System (INIS)

    Rogers, W.L.; Wainstock, M.A.

    1976-01-01

    An apparatus and method for locating or directing a source of ionizing radiation such as X-rays, gamma rays, alpha particles, beta particles, etc. are described. The preferred embodiment detects and locates abnormalities of the body such as ocular melanomas by detecting the emission of radiation from a melanoma which has absorbed a radioactive medium. The apparatus includes an ultrasound probe which emits ultrasonic waves along a first axis and detects a returned portion of the waves. The ultrasound probe is associated with a display which displays the returned portion of the waves in the time domain so that suspected abnormalities can be located. The ultrasound probe is used to guide a directional probe for detecting and quantifying ionizing radiation which is equipped with a focusing collimator having a focal point along a second axis. The two probes are supported so that the first and second axes converge at the focal point of the collimator. A range marker is associated with the ultrasonic detector which indicates the point of convergence of the axes on the ultrasonic display permitting guidance of the radiation detecting probe to the suspected abnormality

  7. Reduction Assessment of Agricultural Non-Point Source Pollutant Loading

    OpenAIRE

    Fu, YiCheng; Zang, Wenbin; Zhang, Jian; Wang, Hongtao; Zhang, Chunling; Shi, Wanli

    2018-01-01

    NPS (Non-point source) pollution has become a key impact element to watershed environment at present. With the development of technology, application of models to control NPS pollution has become a very common practice for resource management and Pollutant reduction control in the watershed scale of China. The SWAT (Soil and Water Assessment Tool) model is a semi-conceptual model, which was put forward to estimate pollutant production & the influences on water quantity-quality under different...

  8. Diffusion from a point source in an urban atmosphere

    International Nuclear Information System (INIS)

    Essa, K.S.M.; El-Otaify, M.S.

    2005-01-01

    In the present paper, a model for the diffusion of material from a point source in an urban atmosphere is incorporated. The plume is assumed to have a well-defined edge at which the concentration falls to zero. The vertical wind shear is estimated using logarithmic law, by employing most of the available techniques of stability categories. The concentrations estimated from the model were compared favorably with the field observations of other investigators

  9. Source location of Jupiter's decametric radiation and UV aurora

    Science.gov (United States)

    Maeda, Koitiro; Carr, Thomas D.

    1989-01-01

    The source region of a component of Jovian Io-unrelated decametric radiation is inferred geometrically based on simultaneous observations from Voyager spacecraft and a ground-based observatory with the aid of a hollow cone beam model and model of the Jovian magnetic field. The results indicate that the sources of this component lie above the northern hemisphere, and on field lines that connect the Io plasma torus and the Jovian ionosphere in the so-called active sector. It is concluded that an interaction between the Io-torus plasma and the ionospheric plasma through a thin flux tube initiates the decametric radiation.

  10. A search for point sources of EeV photons

    Energy Technology Data Exchange (ETDEWEB)

    Aab, A. [Universität Siegen, Siegen (Germany); Abreu, P.; Andringa, S. [Laboratório de Instrumentação e Física Experimental de Partículas (LIP) and Instituto Superior Técnico (IST), Universidade de Lisboa (Portugal); Aglietta, M. [Osservatorio Astrofisico di Torino (INAF), Università di Torino and Sezione INFN, Torino (Italy); Ahlers, M. [University of Wisconsin, Madison, WI (United States); Ahn, E. J. [Fermilab, Batavia, IL (United States); Al Samarai, I. [Institut de Physique Nucléaire d' Orsay (IPNO), Université Paris 11, CNRS-IN2P3, Orsay (France); Albuquerque, I. F. M. [Universidade de São Paulo, Instituto de Física, São Paulo, SP (Brazil); Allekotte, I. [Centro Atómico Bariloche and Instituto Balseiro (CNEA-UNCuyo-CONICET), San Carlos de Bariloche (Argentina); Allen, J. [New York University, New York, NY (United States); Allison, P. [Ohio State University, Columbus, OH (United States); Almela, A. [Universidad Tecnológica Nacional—Facultad Regional Buenos Aires, Buenos Aires (Argentina); Castillo, J. Alvarez [Universidad Nacional Autonoma de Mexico, Mexico, D. F. (Mexico); Alvarez-Muñiz, J. [Universidad de Santiago de Compostela (Spain); Batista, R. Alves [Universität Hamburg, Hamburg (Germany); Ambrosio, M.; Aramo, C. [Università di Napoli " Federico II" and Sezione INFN, Napoli (Italy); Aminaei, A. [IMAPP, Radboud University Nijmegen (Netherlands); Anchordoqui, L. [University of Wisconsin, Milwaukee, WI (United States); Arqueros, F. [Universidad Complutense de Madrid, Madrid (Spain); Collaboration: Pierre Auger Collaboration102; and others

    2014-07-10

    Measurements of air showers made using the hybrid technique developed with the fluorescence and surface detectors of the Pierre Auger Observatory allow a sensitive search for point sources of EeV photons anywhere in the exposed sky. A multivariate analysis reduces the background of hadronic cosmic rays. The search is sensitive to a declination band from –85° to +20°, in an energy range from 10{sup 17.3} eV to 10{sup 18.5} eV. No photon point source has been detected. An upper limit on the photon flux has been derived for every direction. The mean value of the energy flux limit that results from this, assuming a photon spectral index of –2, is 0.06 eV cm{sup –2} s{sup –1}, and no celestial direction exceeds 0.25 eV cm{sup –2} s{sup –1}. These upper limits constrain scenarios in which EeV cosmic ray protons are emitted by non-transient sources in the Galaxy.

  11. Open-Source Automated Mapping Four-Point Probe.

    Science.gov (United States)

    Chandra, Handy; Allen, Spencer W; Oberloier, Shane W; Bihari, Nupur; Gwamuri, Jephias; Pearce, Joshua M

    2017-01-26

    Scientists have begun using self-replicating rapid prototyper (RepRap) 3-D printers to manufacture open source digital designs of scientific equipment. This approach is refined here to develop a novel instrument capable of performing automated large-area four-point probe measurements. The designs for conversion of a RepRap 3-D printer to a 2-D open source four-point probe (OS4PP) measurement device are detailed for the mechanical and electrical systems. Free and open source software and firmware are developed to operate the tool. The OS4PP was validated against a wide range of discrete resistors and indium tin oxide (ITO) samples of different thicknesses both pre- and post-annealing. The OS4PP was then compared to two commercial proprietary systems. Results of resistors from 10 to 1 MΩ show errors of less than 1% for the OS4PP. The 3-D mapping of sheet resistance of ITO samples successfully demonstrated the automated capability to measure non-uniformities in large-area samples. The results indicate that all measured values are within the same order of magnitude when compared to two proprietary measurement systems. In conclusion, the OS4PP system, which costs less than 70% of manual proprietary systems, is comparable electrically while offering automated 100 micron positional accuracy for measuring sheet resistance over larger areas.

  12. Open-Source Automated Mapping Four-Point Probe

    Directory of Open Access Journals (Sweden)

    Handy Chandra

    2017-01-01

    Full Text Available Scientists have begun using self-replicating rapid prototyper (RepRap 3-D printers to manufacture open source digital designs of scientific equipment. This approach is refined here to develop a novel instrument capable of performing automated large-area four-point probe measurements. The designs for conversion of a RepRap 3-D printer to a 2-D open source four-point probe (OS4PP measurement device are detailed for the mechanical and electrical systems. Free and open source software and firmware are developed to operate the tool. The OS4PP was validated against a wide range of discrete resistors and indium tin oxide (ITO samples of different thicknesses both pre- and post-annealing. The OS4PP was then compared to two commercial proprietary systems. Results of resistors from 10 to 1 MΩ show errors of less than 1% for the OS4PP. The 3-D mapping of sheet resistance of ITO samples successfully demonstrated the automated capability to measure non-uniformities in large-area samples. The results indicate that all measured values are within the same order of magnitude when compared to two proprietary measurement systems. In conclusion, the OS4PP system, which costs less than 70% of manual proprietary systems, is comparable electrically while offering automated 100 micron positional accuracy for measuring sheet resistance over larger areas.

  13. Low-energy point source searches with IceCube

    Directory of Open Access Journals (Sweden)

    Euler Sebastian

    2016-01-01

    Full Text Available Due to the overwhelming background of atmospheric muons, the traditional IceCube point source search in the Southern Hemisphere is mainly sensitive to neutrinos with energies above 100TeV. A new approach focuses on events starting inside the instrumented volume. By utilizing different veto techniques we are able to significantly reduce the energy threshold and can now for the first time explore the entire Southern Hemisphere at neutrino energies as low as 100GeV. We present the results of two analyses targeting slightly different energy ranges. Both use one year of data taken with the completed IceCube detector in 2011/12.

  14. Locating sources within a dense sensor array using graph clustering

    Science.gov (United States)

    Gerstoft, P.; Riahi, N.

    2017-12-01

    We develop a model-free technique to identify weak sources within dense sensor arrays using graph clustering. No knowledge about the propagation medium is needed except that signal strengths decay to insignificant levels within a scale that is shorter than the aperture. We then reinterpret the spatial coherence matrix of a wave field as a matrix whose support is a connectivity matrix of a graph with sensors as vertices. In a dense network, well-separated sources induce clusters in this graph. The geographic spread of these clusters can serve to localize the sources. The support of the covariance matrix is estimated from limited-time data using a hypothesis test with a robust phase-only coherence test statistic combined with a physical distance criterion. The latter criterion ensures graph sparsity and thus prevents clusters from forming by chance. We verify the approach and quantify its reliability on a simulated dataset. The method is then applied to data from a dense 5200 element geophone array that blanketed of the city of Long Beach (CA). The analysis exposes a helicopter traversing the array and oil production facilities.

  15. Preparation of very small point sources for high resolution radiography

    International Nuclear Information System (INIS)

    Case, F.N.

    1976-01-01

    The need for very small point sources of high specific activity 192 Ir, 169 Yb, 170 Tm, and 60 Co in non-destructive testing has motivated the development of techniques for the fabrication of these sources. To prepare 192 Ir point sources for use in examination of tube sheet welds in LMFBR heat exchangers, 191 Ir enriched to greater than 90 percent was melted in a helium blanketed arc to form spheres as small as 0.38 mm in diameter. Methods were developed to form the roughly spherical shaped arc product into nearly symmetrical spheres that could be used for high resolution radiography. Similar methods were used for spherical shaped sources of 169 Yb and 170 Tm. The oxides were arc melted to form rough spheres followed by grinding to precise dimensions, neutron irradiation of the spheres at a flux of 2 to 3 x 10 15 nv, and use of enriched 168 Yb to provide the maximum specific activity. Cobalt-60 with a specific activity of greater than 1100 Ci/g was prepared by processing 59 Co that had been neutron irradiated to nearly complete burnup of the 59 Co target to produce 60 Co, 61 Ni, and 62 Ni. Ion exchange methods were used to separate the cobalt from the nickel. The cobalt was reduced to metal by plating either onto aluminum foil which was dissolved away from the cobalt plate, or by plating onto mercury to prepare amalgam that could be easily formed into a pellet of cobalt with exclusion of the mercury. Both methods are discussed

  16. First combined search for neutrino point-sources in the Southern Hemispherewith the ANTARES and IceCube neutrino telescopes

    NARCIS (Netherlands)

    Adrian-Martinez, S.; van Haren, H.; ANTARES Collaboration; IceCube Collaboration

    2016-01-01

    We present the results of searches for point-like sources of neutrinos based on the ?rstcombined analysis of data from both the ANTARES and IceCube neutrino telescopes.The combination of both detectors which di?er in size and location forms a window inthe Southern sky where the sensitivity to point

  17. Outbreaks source: A new mathematical approach to identify their possible location

    Science.gov (United States)

    Buscema, Massimo; Grossi, Enzo; Breda, Marco; Jefferson, Tom

    2009-11-01

    Classical epidemiology has generally relied on the description and explanation of the occurrence of infectious diseases in relation to time occurrence of events rather than to place of occurrence. In recent times, computer generated dot maps have facilitated the modeling of the spread of infectious epidemic diseases either with classical statistics approaches or with artificial “intelligent systems”. Few attempts, however, have been made so far to identify the origin of the epidemic spread rather than its evolution by mathematical topology methods. We report on the use of a new artificial intelligence method (the H-PST Algorithm) and we compare this new technique with other well known algorithms to identify the source of three examples of infectious disease outbreaks derived from literature. The H-PST algorithm is a new system able to project a distances matrix of points (events) into a bi-dimensional space, with the generation of a new point, named hidden unit. This new hidden unit deforms the original Euclidean space and transforms it into a new space (cognitive space). The cost function of this transformation is the minimization of the differences between the original distance matrix among the assigned points and the distance matrix of the same points projected into the bi-dimensional map (or any different set of constraints). For many reasons we will discuss, the position of the hidden unit shows to target the outbreak source in many epidemics much better than the other classic algorithms specifically targeted for this task. Compared with main algorithms known in the location theory, the hidden unit was within yards of the outbreak source in the first example (the 2007 epidemic of Chikungunya fever in Italy). The hidden unit was located in the river between the two village epicentres of the spread exactly where the index case was living. Equally in the second (the 1967 foot and mouth disease epidemic in England), and the third (1854 London Cholera epidemic

  18. An approach for de-identification of point locations of livestock premises for further use in disease spread modeling.

    Science.gov (United States)

    Martin, Michael K; Helm, Julie; Patyk, Kelly A

    2015-06-15

    We describe a method for de-identifying point location data used for disease spread modeling to allow data custodians to share data with modeling experts without disclosing individual farm identities. The approach is implemented in an open-source software program that is described and evaluated here. The program allows a data custodian to select a level of de-identification based on the K-anonymity statistic. The program converts a file of true farm locations and attributes into a file appropriate for use in disease spread modeling with the locations randomly modified to prevent re-identification based on location. Important epidemiological relationships such as clustering are preserved to as much as possible to allow modeling similar to those using true identifiable data. The software implementation was verified by visual inspection and basic descriptive spatial analysis of the output. Performance is sufficient to allow de-identification of even large data sets on desktop computers available to any data custodian. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. The peak efficiency calibration of volume source using 152Eu point source in computer

    International Nuclear Information System (INIS)

    Shen Tingyun; Qian Jianfu; Nan Qinliang; Zhou Yanguo

    1997-01-01

    The author describes the method of the peak efficiency calibration of volume source by means of 152 Eu point source for HPGe γ spectrometer. The peak efficiency can be computed by Monte Carlo simulation, after inputting parameter of detector. The computation results are in agreement with the experimental results with an error of +-3.8%, with an exception one is about +-7.4%

  20. Nonpoint and Point Sources of Nitrogen in Major Watersheds of the United States

    Science.gov (United States)

    Puckett, Larry J.

    1994-01-01

    Estimates of nonpoint and point sources of nitrogen were made for 107 watersheds located in the U.S. Geological Survey's National Water-Quality Assessment Program study units throughout the conterminous United States. The proportions of nitrogen originating from fertilizer, manure, atmospheric deposition, sewage, and industrial sources were found to vary with climate, hydrologic conditions, land use, population, and physiography. Fertilizer sources of nitrogen are proportionally greater in agricultural areas of the West and the Midwest than in other parts of the Nation. Animal manure contributes large proportions of nitrogen in the South and parts of the Northeast. Atmospheric deposition of nitrogen is generally greatest in areas of greatest precipitation, such as the Northeast. Point sources (sewage and industrial) generally are predominant in watersheds near cities, where they may account for large proportions of the nitrogen in streams. The transport of nitrogen in streams increases as amounts of precipitation and runoff increase and is greatest in the Northeastern United States. Because no single nonpoint nitrogen source is dominant everywhere, approaches to control nitrogen must vary throughout the Nation. Watershed-based approaches to understanding nonpoint and point sources of contamination, as used by the National Water-Quality Assessment Program, will aid water-quality and environmental managers to devise methods to reduce nitrogen pollution.

  1. A compiled catalog of rotation measures of radio point sources

    International Nuclear Information System (INIS)

    Xu Jun; Han Jin-Lin

    2014-01-01

    We compiled a catalog of Faraday rotation measures (RMs) for 4553 extragalactic radio point sources published in literature. These RMs were derived from multi-frequency polarization observations. The RM data are compared to those in the NRAO VLA Sky Survey (NVSS) RM catalog. We reveal a systematic uncertainty of about 10.0 ± 1.5 rad m −2 in the NVSS RM catalog. The Galactic foreground RM is calculated through a weighted averaging method by using the compiled RM catalog together with the NVSS RM catalog, with careful consideration of uncertainties in the RM data. The data from the catalog and the interface for the Galactic foreground RM calculations are publicly available on the webpage: http://zmtt.bao.ac.cn/RM/. (research papers)

  2. Trans-Z-source and Γ-Z-source neutral-point-clamped inverters

    DEFF Research Database (Denmark)

    Wei, Mo; Loh, Poh Chiang; Blaabjerg, Frede

    2015-01-01

    Z-source neutral-point-clamped (NPC) inverters are earlier proposed for obtaining voltage buck-boost and three-level switching simultaneously. Their performances are, however, constrained by a trade-off between their input-to-output gain and modulation ratio. This trade-off can lead to high...

  3. Power-Law Template for IR Point Source Clustering

    Science.gov (United States)

    Addison, Graeme E.; Dunkley, Joanna; Hajian, Amir; Viero, Marco; Bond, J. Richard; Das, Sudeep; Devlin, Mark; Halpern, Mark; Hincks, Adam; Hlozek, Renee; hide

    2011-01-01

    We perform a combined fit to angular power spectra of unresolved infrared (IR) point sources from the Planck satellite (at 217,353,545 and 857 GHz, over angular scales 100 law of the form C_l\\propto I(sup -n) with n = 1.25 +/- 0.06. While the IR sources are understood to lie at a range of redshifts, with a variety of dust properties, we find that the frequency dependence of the clustering power can be described by the square of a modified blackbody, nu(sup beta) B(nu,T_eff), with a single emissivity index beta = 2.20 +/- 0.07 and effective temperature T_eff= 9.7 K. Our predictions for the clustering amplitude are consistent with existing ACT and South Pole Telescope results at around 150 and 220 GHz, as is our prediction for the effective dust spectral index, which we find to be alpha_150-220 = 3.68 +/- 0.07 between 150 and 220 GHz. Our constraints on the clustering shape and frequency dependence can be used to model the IR clustering as a contaminant in Cosmic Microwave Background anisotropy measurements. The combined Planck and BLAST data also rule out a linear bias clustering model.

  4. Power-Law Template for Infrared Point-Source Clustering

    Science.gov (United States)

    Addison, Graeme E; Dunkley, Joanna; Hajian, Amir; Viero, Marco; Bond, J. Richard; Das, Sudeep; Devlin, Mark J.; Halpern, Mark; Hincks, Adam D; Hlozek, Renee; hide

    2012-01-01

    We perform a combined fit to angular power spectra of unresolved infrared (IR) point sources from the Planck satellite (at 217, 353, 545, and 857 GHz, over angular scales 100 approx law of the form C(sup clust)(sub l) varies as l (sub -n) with n = 1.25 +/- 0.06. While the IR sources are understood to lie at a range of redshifts, with a variety of dust properties, we find that the frequency dependence of the clustering power can be described by the square of a modified blackbody, ?(sup Beta)B(?, T(sub eff) ), with a single emissivity index Beta = 2.20 +/- 0.07 and effective temperature T(sub eff) = 9.7 K. Our predictions for the clustering amplitude are consistent with existing ACT and South Pole Telescope results at around 150 and 220 GHz, as is our prediction for the effective dust spectral index, which we find to be alpha(sub 150-220) = 3.68 +/- 0.07 between 150 and 220 GHz. Our constraints on the clustering shape and frequency dependence can be used to model the IR clustering as a contaminant in cosmic microwave background anisotropy measurements. The combined Planck and BLAST data also rule out a linear bias clustering model.

  5. A method for acoustic source location in plate-type structures

    Science.gov (United States)

    Mostafapour, Amir; Davoodi, Saman

    2017-09-01

    In this study an algorithm based on Shannon entropy, cross-time frequency spectrum (CTFS) and frequency varying velocities was proposed for structure health monitoring in two-layer plate. A linear array of two sensors is applied to capture the signals. By reducing the number of sensors we used a secondary pattern to get enough information for source locating. For this purpose a pattern for secondary points based on Shannon entropy and cost function was developed. Then to estimate the time delay of signals, cross-time frequency spectrum function was taken from captured signals. The time delay was calculated when CTFS function reached the maximum value. By taking short time Fourier transform of cross correlation function of captures signals and using dispersive curves, time delay and corresponding frequency dependent velocity are estimated. The experiments were carried out and the results showed high precision of presented algorithm.

  6. LEAP: Looking beyond pixels with continuous-space EstimAtion of Point sources

    Science.gov (United States)

    Pan, Hanjie; Simeoni, Matthieu; Hurley, Paul; Blu, Thierry; Vetterli, Martin

    2017-12-01

    Context. Two main classes of imaging algorithms have emerged in radio interferometry: the CLEAN algorithm and its multiple variants, and compressed-sensing inspired methods. They are both discrete in nature, and estimate source locations and intensities on a regular grid. For the traditional CLEAN-based imaging pipeline, the resolution power of the tool is limited by the width of the synthesized beam, which is inversely proportional to the largest baseline. The finite rate of innovation (FRI) framework is a robust method to find the locations of point-sources in a continuum without grid imposition. The continuous formulation makes the FRI recovery performance only dependent on the number of measurements and the number of sources in the sky. FRI can theoretically find sources below the perceived tool resolution. To date, FRI had never been tested in the extreme conditions inherent to radio astronomy: weak signal / high noise, huge data sets, large numbers of sources. Aims: The aims were (i) to adapt FRI to radio astronomy, (ii) verify it can recover sources in radio astronomy conditions with more accurate positioning than CLEAN, and possibly resolve some sources that would otherwise be missed, (iii) show that sources can be found using less data than would otherwise be required to find them, and (iv) show that FRI does not lead to an augmented rate of false positives. Methods: We implemented a continuous domain sparse reconstruction algorithm in Python. The angular resolution performance of the new algorithm was assessed under simulation, and with visibility measurements from the LOFAR telescope. Existing catalogs were used to confirm the existence of sources. Results: We adapted the FRI framework to radio interferometry, and showed that it is possible to determine accurate off-grid point-source locations and their corresponding intensities. In addition, FRI-based sparse reconstruction required less integration time and smaller baselines to reach a comparable

  7. A location-based multiple point statistics method: modelling the reservoir with non-stationary characteristics

    Science.gov (United States)

    Yin, Yanshu; Feng, Wenjie

    2017-12-01

    In this paper, a location-based multiple point statistics method is developed to model a non-stationary reservoir. The proposed method characterizes the relationship between the sedimentary pattern and the deposit location using the relative central position distance function, which alleviates the requirement that the training image and the simulated grids have the same dimension. The weights in every direction of the distance function can be changed to characterize the reservoir heterogeneity in various directions. The local integral replacements of data events, structured random path, distance tolerance and multi-grid strategy are applied to reproduce the sedimentary patterns and obtain a more realistic result. This method is compared with the traditional Snesim method using a synthesized 3-D training image of Poyang Lake and a reservoir model of Shengli Oilfield in China. The results indicate that the new method can reproduce the non-stationary characteristics better than the traditional method and is more suitable for simulation of delta-front deposits. These results show that the new method is a powerful tool for modelling a reservoir with non-stationary characteristics.

  8. Gamma ray burst source locations with the Ulysses/Compton/PVO Network

    International Nuclear Information System (INIS)

    Cline, T.L.; Hurley, K.C.; Boer, M.; Sommer, M.; Niel, M.; Fishman, G.J.; Kouveliotou, C.; Meegan, C.A.; Paciesas, W.S.; Wilson, R.B.; Laros, J.G.; Klebesadel, R.W.

    1991-01-01

    The new interplanetary gamma-ray burst network will determine source fields with unprecedented accuracy. The baseline of the Ulysses mission and the locations of Pioneer-Venus Orbiter and of Mars Observer will ensure precision to a few tens of arc seconds. Combined with the event phenomenologies of the Burst and Transient Source Experiment on Compton Observatory, the source locations to be achieved with this network may provide a basic new understanding of the puzzle of gamma ray bursts

  9. Infrared point sources aligned with the SgrA(asterisk) non-thermal radio source

    Science.gov (United States)

    Stein, W. A.; Forrest, W. J.

    1986-01-01

    Assembled 0.7-5.0 micron observational data for two point sources approximately aligned with the compact nonthermal radio source SgrA(asterisk) in the Galactic center, thus far interpreted as being from the same object on the basis of their position and spectral continuity, are presently given alternative interpretations. While the object must be a hot star surrounded by a circumstellar dust cloud if it is a foreground star, a Galactic center position calls for an unorthodox extinction curve which suggests that the IR emission may be the Rayleigh-Jeans tail of a hot star or star cluster, or perhaps a thermal accretion disk.

  10. Multiwavelength counterparts of the point sources in the Chandra Source Catalog

    Science.gov (United States)

    Reynolds, Michael; Civano, Francesca Maria; Fabbiano, Giuseppina; D'Abrusco, Raffaele

    2018-01-01

    The most recent release of the Chandra Source Catalog (CSC) version 2.0 comprises more than $\\sim$350,000 point sources, down to fluxes of $\\sim$10$^{-16}$ erg/cm$^2$/s, covering $\\sim$500 deg$^2$ of the sky, making it one of the best available X-ray catalogs to date. There are many reasons to have multiwavelength counterparts for sources, one such reason is that X-ray information alone is not enough to identify the sources and divide them between galactic and extragalactic origin, therefore multiwavelength data associated to each X-ray source is crucial for classification and scientific analysis of the sample. To perform this multiwavelength association, we are going to employ the recently released versatile tool NWAY (Salvato et al. 2017), based on a Bayesian algorithm for cross-matching multiple catalogs. NWAY allows the combination of multiple catalogs at the same time, provides a probability for the matches, even in case of non-detection due to different depth of the matching catalogs, and it can be used by including priors on the nature of the sources (e.g. colors, magnitudes, etc). In this poster, we are presenting the preliminary analysis using the CSC sources above the galactic plane matched to the WISE All-Sky catalog, SDSS, Pan-STARRS and GALEX.

  11. Low energy electron point source microscopy: beyond imaging.

    Science.gov (United States)

    Beyer, André; Gölzhäuser, Armin

    2010-09-01

    Low energy electron point source (LEEPS) microscopy has the capability to record in-line holograms at very high magnifications with a fairly simple set-up. After the holograms are numerically reconstructed, structural features with the size of about 2 nm can be resolved. The achievement of an even higher resolution has been predicted. However, a number of obstacles are known to impede the realization of this goal, for example the presence of electric fields around the imaged object, electrostatic charging or radiation induced processes. This topical review gives an overview of the achievements as well as the difficulties in the efforts to shift the resolution limit of LEEPS microscopy towards the atomic level. A special emphasis is laid on the high sensitivity of low energy electrons to electrical fields, which limits the structural determination of the imaged objects. On the other hand, the investigation of the electrical field around objects of known structure is very useful for other tasks and LEEPS microscopy can be extended beyond the task of imaging. The determination of the electrical resistance of individual nanowires can be achieved by a proper analysis of the corresponding LEEPS micrographs. This conductivity imaging may be a very useful application for LEEPS microscopes.

  12. BEAMLINE-CONTROLLED STEERING OF SOURCE-POINT ANGLE AT THE ADVANCED PHOTON SOURCE

    Energy Technology Data Exchange (ETDEWEB)

    Emery, L.; Fystro, G.; Shang, H.; Smith, M.

    2017-06-25

    An EPICS-based steering software system has been implemented for beamline personnel to directly steer the angle of the synchrotron radiation sources at the Advanced Photon Source. A script running on a workstation monitors "start steering" beamline EPICS records, and effects a steering given by the value of the "angle request" EPICS record. The new system makes the steering process much faster than before, although the older steering protocols can still be used. The robustness features of the original steering remain. Feedback messages are provided to the beamlines and the accelerator operators. Underpinning this new steering protocol is the recent refinement of the global orbit feedback process whereby feedforward of dipole corrector set points and orbit set points are used to create a local steering bump in a rapid and seamless way.

  13. An eikonal-based formulation for traveltime perturbation with respect to the source location

    KAUST Repository

    Alkhalifah, Tariq

    2010-11-01

    Traveltime calculations amount to solving the nonlinear eikonal equation for a given source location. The relationship between the eikonal solution and its perturbations is analyzed with respect to the source location and a partial differential equation is developed that relates the traveltime field for one source location to that for a nearby source. This linear first-order equation in one form depends on lateral changes in velocity and in another form is independent of the velocity field and relies on second-order derivatives of the original traveltime field. For stable finite-difference calculations, this requires the velocity field to be smooth in a sense similar to ray-tracing requirements. Our formulation for traveltime perturbation has several potential applications, such that as traveltime calculation by source-location perturbation, velocity-independent interpolation including datuming, and velocity estimation. Additionally, higher-order expansions provide parameters necessary for Gaussian-beam computations. © 2010 Society of Exploration Geophysicists.

  14. A New Wave Equation Based Source Location Method with Full-waveform Inversion

    KAUST Repository

    Wu, Zedong

    2017-05-26

    Locating the source of a passively recorded seismic event is still a challenging problem, especially when the velocity is unknown. Many imaging approaches to focus the image do not address the velocity issue and result in images plagued with illumination artifacts. We develop a waveform inversion approach with an additional penalty term in the objective function to reward the focusing of the source image. This penalty term is relaxed early to allow for data fitting, and avoid cycle skipping, using an extended source. At the later stages the focusing of the image dominates the inversion allowing for high resolution source and velocity inversion. We also compute the source location explicitly and numerical tests show that we obtain good estimates of the source locations with this approach.

  15. Point source detection performance of Hard X-ray Modulation Telescope imaging observation

    International Nuclear Information System (INIS)

    Huo, Zhuo-Xi; Li, Yi-Ming; Li, Xiao-Bo; Zhou, Jian-Feng

    2015-01-01

    The Hard X-ray Modulation Telescope (HXMT) will perform an all-sky survey in the hard X-ray band as well as deep imaging of a series of small sky regions. We expect various compact objects to be detected in these imaging observations. Point source detection performance of HXMT imaging observation depends not only on the instrument but also on the data analysis method that is applied since images are reconstructed from HXMT observed data with numerical methods. The denoising technique used plays an important part in the HXMT imaging data analysis pipeline along with demodulation and source detection. In this paper we have implemented several methods for denoising HXMT data and evaluated the point source detection performances in terms of sensitivities and location accuracies. The results show that direct demodulation with 1-fold cross-correlation should be the default reconstruction and regularization method, although both sensitivity and location accuracy could be further improved by selecting and tuning numerical methods in data analysis used for HXMT imaging observations. (paper)

  16. Protecting multi-party privacy in location-aware social point-of-interest recommendation

    KAUST Repository

    Wang, Weiqi

    2018-04-04

    Point-of-interest (POI) recommendation has attracted much interest recently because of its significant business potential. Data used in POI recommendation (e.g., user-location check-in matrix) are much more sparse than that used in traditional item (e.g., book and movie) recommendation, which leads to more serious cold start problem. Social POI recommendation has proved to be an effective solution, but most existing works assume that recommenders have access to all required data. This is very rare in practice because these data are generally owned by different entities who are not willing to share their data with others due to privacy and legal concerns. In this paper, we first propose PLAS, a protocol which enables effective POI recommendation without disclosing the sensitive data of every party getting involved in the recommendation. We formally show PLAS is secure in the semi-honest adversary model. To improve its performance. We then adopt the technique of cloaking area by which expensive distance computation over encrypted data is replaced by cheap operation over plaintext. In addition, we utilize the sparsity of check-ins to selectively publish data, thus reducing encryption cost and avoiding unnecessary computation over ciphertext. Experiments on two real datasets show that our protocol is feasible and can scale to large POI recommendation problems in practice.

  17. Offshore Pipeline Locations in the Gulf of Mexico, Geographic NAD27, MMS (2007) [pipelines_points_mms_2007

    Data.gov (United States)

    Louisiana Geographic Information Center — Offshore Minerals Management Pipeline Locations for the Gulf of Mexico (GOM). Contains the points of the pipeline in the GOM. All pipelines existing in the databases...

  18. Nutrient Losses from Non-Point Sources or from Unidentified Point Sources? Application Examples of the Smartphone Based Nitrate App.

    Science.gov (United States)

    Rozemeijer, J.; Ekkelenkamp, R.; van der Zaan, B.

    2017-12-01

    In 2016 Deltares launched the free to use Nitrate App which accurately reads and interprets nitrate test strips. The app directly displays the measured concentration and gives the option to share the result. Shared results are visualised in map functionality within the app and online. Since its introduction we've been seeing an increasing number of nitrate app applications. In this presentation we show some unanticipated types of application. The Nitrate App was originally intended to enable farmers to measure nitrate concentrations on their own farms. This may encourage farmers to talk to specialists about the right nutrient best management practices (BMP's) for their farm. Several groups of farmers have recently started to apply the Nitrate App and to discuss their results with each other and with the authorities. Nitrate concentration routings in catchments have proven to be another useful application. Within a day a person can generate a catchment scale nitrate concentration map identifying nitrate loss hotspots. In several routings in agricultural catchments clear point sources were found, for example at small scale manure processing plants. These routings proved that the Nitrate App can help water managers to target conservation practices more accurately to areas with the highest nitrate concentrations and loads. Other current applications are the screening of domestic water wells in California, the collection of extra measurements (also pH and NH4) in the National Monitoring Network for the Evaluation of the Manure Policy in the Netherlands, and several educational initiatives in cooperation with schools and universities.

  19. Location of acoustic radiators and inversion for energy density using radio-frequency sources and thunder recordings

    Science.gov (United States)

    Anderson, J.; Johnson, J. B.; Arechiga, R. O.; Edens, H. E.; Thomas, R. J.

    2011-12-01

    We use radio frequency (VHF) pulse locations mapped with the New Mexico Tech Lightning Mapping Array (LMA) to study the distribution of thunder sources in lightning channels. A least squares inversion is used to fit channel acoustic energy radiation with broadband (0.01 to 500 Hz) acoustic recordings using microphones deployed local (lightning. We model the thunder (acoustic) source as a superposition of line segments connecting the LMA VHF pulses. An optimum branching algorithm is used to reconstruct conductive channels delineated by VHF sources, which we discretize as a superposition of finely-spaced (0.25 m) acoustic point sources. We consider total radiated thunder as a weighted superposition of acoustic waves from individual channels, each with a constant current along its length that is presumed to be proportional to acoustic energy density radiated per unit length. Merged channels are considered as a linear sum of current-carrying branches and radiate proportionally greater acoustic energy. Synthetic energy time series for a given microphone location are calculated for each independent channel. We then use a non-negative least squares inversion to solve for channel energy densities to match the energy time series determined from broadband acoustic recordings across a 4-station microphone network. Events analyzed by this method have so far included 300-1000 VHF sources, and correlations as high as 0.5 between synthetic and recorded thunder energy were obtained, despite the presence of wind noise and 10-30 m uncertainty in VHF source locations.

  20. Impact of point source pollution on groundwater quality

    International Nuclear Information System (INIS)

    Gill, M.A.; Solehria, B.A.; Rai, N.I.

    2005-01-01

    The management of point source pollution (municipal and industrial waste water) is an important item on Brown Agenda confronting urban planners and policy makers. The industrial concerns and households produce enormous amount of waste water, which has to be disposed of through the municipal sewage system. Generally, municipal wastewater management is done on non-scientific lines, resulting in considerable social and economic loss and gradual degradation of the natural resources. The present study highlights that how the poor management practices, lack of infrastructure, and poor disposal system-comprising of mostly open, un-walled or partially lined drains, affect the groundwater quality and render it unfit for human consumption. Satiana Road sludge carrier at Faisalabad city, receiving effluents of about 67 textile units, 4 oil mills, 2 ice factories, 3 laundris and domestic waste water of Peoples Colony No.1, Maqbool Road and Ghulam Rasool Nagar was selected to derive quantitative and qualitative estimates of TDS, Na, Cl and heavy metals namely Fe, Cu and Pb of the waste water and their leaching around the sludge carrier. The measurement of leaching of TDS, Na/sup +/, and Cl/sup -1/ per 1000 m basis in lined section was 818, 550 and 228 tons, respectively. Where as in the unlined section, annual increase of TDS, Na/sup /+, and Cl/sup -/ was 2404,1615 and 669 tons per 1000 m respectively. In case of leaching of metals through the sludge carrier, Cu was at the top with 8.4 tons per annum per 1000 m followed by Fe and Pb with 6.66 and 1.2 tons per annum per 1000 m respectively. The concentration of all the salts/metals studied were higher in groundwater near the sludge carrier which decreased with increase in distance. The groundwater contamination in unlined portions is greater than lined portions, which might be due to higher seepage losses in unlined portions of the sludge carrier (4.9 % per 1000 m) as compared to relatively low seepage losses in lined portion of

  1. Morphology, chemistry and distribution of neoformed spherulites in agricultural land affected by metallurgical point-source pollution

    NARCIS (Netherlands)

    Leguedois, S.; Oort, van F.; Jongmans, A.G.; Chevalier, P.

    2004-01-01

    Metal distribution patterns in superficial soil horizons of agricultural land affected by metallurgical point-source pollution were studied using optical and electron microscopy, synchrotron radiation and spectroscopy analyses. The site is located in northern France, at the center of a former entry

  2. CO2 point sources and subsurface storage capacities for CO2 in aquifers in Norway

    International Nuclear Information System (INIS)

    Boee, Reidulv; Magnus, Christian; Osmundsen, Per Terje; Rindstad, Bjoern Ivar

    2002-01-01

    The GESTCO project comprises a study of the distribution and coincidence of thermal CO 2 emission sources and location/quality of geological storage capacity in Europe. Four of the most promising types of geological storage are being studied. 1. Onshore/offshore saline aquifers with or without lateral seal. 2. Low entalpy geothermal reservoirs. 3. Deep methane-bearing coal beds and abandoned coal and salt mines. 4. Exhausted or near exhausted hydrocarbon structures. In this report we present an inventory of CO 2 point sources in Norway (1999) and the results of the work within Study Area C: Deep saline aquifers offshore/near shore Northern and Central Norway. Also offshore/near shore Southern Norway has been included while the Barents Sea is not described in any detail. The most detailed studies are on the Tilje and Aare Formations on the Troendelag Platform off Mid-Norway and on the Sognefjord, Fensfjord and Krossfjord Formations, southeast of the Troll Field off Western Norway. The Tilje Formation has been chosen as one of the cases to be studied in greater detail (numerical modelling) in the project. This report shows that offshore Norway, there are concentrations of large CO 2 point sources in the Haltenbanken, the Viking Graben/Tampen Spur area, the Southern Viking Graben and the central Trough, while onshore Norway there are concentrations of point sources in the Oslofjord/Porsgrund area, along the coast of western Norway and in the Troendelag. A number of aquifers with large theoretical CO 2 storage potential are pointed out in the North Sea, the Norwegian Sea and in the Southern Barents Sea. The storage capacity in the depth interval 0.8 - 4 km below sea level is estimated to be ca. 13 Gt (13000000000 tonnes) CO 2 in geological traps (outside hydrocarbon fields), while the storage capacity in aquifers not confined to traps is estimated to be at least 280 Gt CO 2 . (Author)

  3. Neutron gamma fraction imaging: Detection, location and identification of neutron sources

    Energy Technology Data Exchange (ETDEWEB)

    Gamage, K.A.A., E-mail: k.gamage@lancaster.ac.uk [Department of Engineering, University of Lancaster , Lancaster LA1 4YR (United Kingdom); Taylor, G.C. [National Physical Laboratory, Hampton Road,Teddington, Middlesex TW11 0LW (United Kingdom)

    2015-07-11

    In this paper imaging of neutron sources and identification and separation of a neutron source from another neutron source is described. The system is based upon organic liquid scintillator detector, tungsten collimator, bespoke fast digitiser and adjustable equatorial mount. Three environments have been investigated with this setup corresponding to an AmBe neutron source, a {sup 252}Cf neutron source and both sources together separated in space. In each case, events are detected, digitised, discriminated and radiation images plotted corresponding to the area investigated. The visualised neutron count distributions clearly locate the neutron source and, relative gamma to neutron (or neutron to gamma) fraction images aid in discriminating AmBe sources from {sup 252}Cf source. The measurements were performed in the low scatter facility of the National Physical Laboratory, Teddington, UK.

  4. An efficient closed-form solution for acoustic emission source location in three-dimensional structures

    Directory of Open Access Journals (Sweden)

    Xibing Li

    2014-02-01

    Full Text Available This paper presents an efficient closed-form solution (ECS for acoustic emission(AE source location in three-dimensional structures using time difference of arrival (TDOA measurements from N receivers, N ≥ 6. The nonlinear location equations of TDOA are simplified to linear equations. The unique analytical solution of AE sources for unknown velocity system is obtained by solving the linear equations. The proposed ECS method successfully solved the problems of location errors resulting from measured deviations of velocity as well as the existence and multiplicity of solutions induced by calculations of square roots in existed close-form methods.

  5. The Development and Application of Spatiotemporal Metrics for the Characterization of Point Source FFCO2 Emissions and Dispersion

    Science.gov (United States)

    Roten, D.; Hogue, S.; Spell, P.; Marland, E.; Marland, G.

    2017-12-01

    There is an increasing role for high resolution, CO2 emissions inventories across multiple arenas. The breadth of the applicability of high-resolution data is apparent from their use in atmospheric CO2 modeling, their potential for validation of space-based atmospheric CO2 remote-sensing, and the development of climate change policy. This work focuses on increasing our understanding of the uncertainty in these inventories and the implications on their downstream use. The industrial point sources of emissions (power generating stations, cement manufacturing plants, paper mills, etc.) used in the creation of these inventories often have robust emissions characteristics, beyond just their geographic location. Physical parameters of the emission sources such as number of exhaust stacks, stack heights, stack diameters, exhaust temperatures, and exhaust velocities, as well as temporal variability and climatic influences can be important in characterizing emissions. Emissions from large point sources can behave much differently than emissions from areal sources such as automobiles. For many applications geographic location is not an adequate characterization of emissions. This work demonstrates the sensitivities of atmospheric models to the physical parameters of large point sources and provides a methodology for quantifying parameter impacts at multiple locations across the United States. The sensitivities highlight the importance of location and timing and help to highlight potential aspects that can guide efforts to reduce uncertainty in emissions inventories and increase the utility of the models.

  6. A location procedure for sound sources in reactor-technical enclosures

    International Nuclear Information System (INIS)

    Hamann, D.

    1982-07-01

    A passive method requiring one detector only has been developed for the location of sound emitting faults in nuclear power plant components. It is adapted for use in a frequency range the wavelength of which is of the same order of magnitude as characteristic dimensions of the considered enclosure. The location is performed in the following way: (1) For a fixed detector position the Auto Power Spectral Density (APSD) of the source to be located is measured. (2) For this detector position the APSD is calculated for the potential source locations. For this, the free-field APSD as well as the acoustic normal modes of the enclosure are necessary. (3) The measured APSD is compared with the theoretically obtained APSD's. (4) That APSD is determined which is most similar to the measured APSD, and consequently an information about the unknown source position is got. (author)

  7. Effect of trigger point injection on lumbosacral radiculopathy source.

    Science.gov (United States)

    Saeidian, Seyed Reza; Pipelzadeh, Mohammad Reza; Rasras, Saleh; Zeinali, Masud

    2014-10-01

    Active muscular trigger points (aMTPs) presenting with radiating pain can interfere in diagnosis and treatment of patients suffering from lumbosacral radiculopathy. We aimed to diagnose and evaluate the trigger point therapy on the outcome of pain in patients with lumbosacral radiculopathy. A total of 98 patients were enrolled suffered with chronic pain andlumbosacral radiculopathy at L4-L5 and L5-S1 who were candidates of non-surgical management. All patients received conservative modalities, including bed rest, non-steroidal anti-inflammatory agents (NSAID), and physiotherapy. These treatments continued for a week. Patients were examined for the presence of trigger points in their lower extremities. Those who had trigger points were divided into 2 groups (TP and N). Patients in TP group underwent trigger point injection therapy. No further therapy was done for the N group. Pain scores and straight leg raise (SLR) test in both groups were collected and analyzed on the seventh and 10th days of the therapy. Results were analyzed by paired t test and chi-square test. Out of 98 patients, 64 had trigger points. Thirty-two patients were assigned to each group. Pain scores (Mean ± SD) in TP group was 7.12 ± 1.13 and in N group was 6.7 ± 1.16, P = 0.196. Following the treatment, pain scores were 2.4 ± 1.5 in TP group and 4.06 ± 1.76 in N group P = 0.008. SLR test became negative in all patients in TP group but only in 6 (19%) patients in N group, P = 0.001. Results show that trigger point injection therapy in patients suffering from chronic lumbosacral radiculopathy with trigger points can significantly improve their recovery, and conservative therapy may not be adequate.

  8. An Undersea Mining Microseism Source Location Algorithm Considering Wave Velocity Probability Distribution

    Directory of Open Access Journals (Sweden)

    Furui Du

    2014-01-01

    Full Text Available The traditional mine microseism locating methods are mainly based on the assumption that the wave velocity is uniform through the space, which leads to some errors for the assumption goes against the laws of nature. In this paper, the wave velocity is regarded as a random variable, and the probability distribution information of the wave velocity is fused into the traditional locating method. This paper puts forwards the microseism source location method for the undersea mining on condition of the probability distribution of the wave velocity and comes up with the solving process of Monte Carlo. In addition, based on the simulated results of the Monte Carlo method, the space is divided into three areas: the most possible area (area I, the possible area (area II, and the small probability area (area III. Attached to corresponding mathematical formulations, spherical models and cylindrical models in different areas are, respectively, built according to whether the source is in the sensor arrays. Both the examples and the actual applications show that (1 the method of microseism source location in this paper can highly improve the accuracy of the microseism monitoring, especially for the source beyond the sensor arrays, and (2 the space-dividing method based on occurrence possibilities of the source can recognize and sweep the hidden dangers for it predicts the probable location range of the source efficiently, while the traditional method cannot.

  9. LAT 2-year Point Source Catalog Aperture Photometry Lightcurves

    Data.gov (United States)

    National Aeronautics and Space Administration — Due to a glitch in the analysis pipeline there are apparent increases in flux around MJD 56810 for many sources. These increases are not real and should be...

  10. LAT 2-year Point Source Catalog Aperture Photometry Lightcurves Flares

    Data.gov (United States)

    National Aeronautics and Space Administration — Due to a glitch in the analysis pipeline there are apparent increases in flux around MJD 56810 for many sources. These increases are not real and should be...

  11. Lessons Learned from OMI Observations of Point Source SO2 Pollution

    Science.gov (United States)

    Krotkov, N.; Fioletov, V.; McLinden, Chris

    2011-01-01

    The Ozone Monitoring Instrument (OMI) on NASA Aura satellite makes global daily measurements of the total column of sulfur dioxide (SO2), a short-lived trace gas produced by fossil fuel combustion, smelting, and volcanoes. Although anthropogenic SO2 signals may not be detectable in a single OMI pixel, it is possible to see the source and determine its exact location by averaging a large number of individual measurements. We describe new techniques for spatial and temporal averaging that have been applied to the OMI SO2 data to determine the spatial distributions or "fingerprints" of SO2 burdens from top 100 pollution sources in North America. The technique requires averaging of several years of OMI daily measurements to observe SO2 pollution from typical anthropogenic sources. We found that the largest point sources of SO2 in the U.S. produce elevated SO2 values over a relatively small area - within 20-30 km radius. Therefore, one needs higher than OMI spatial resolution to monitor typical SO2 sources. TROPOMI instrument on the ESA Sentinel 5 precursor mission will have improved ground resolution (approximately 7 km at nadir), but is limited to once a day measurement. A pointable geostationary UVB spectrometer with variable spatial resolution and flexible sampling frequency could potentially achieve the goal of daily monitoring of SO2 point sources and resolve downwind plumes. This concept of taking the measurements at high frequency to enhance weak signals needs to be demonstrated with a GEOCAPE precursor mission before 2020, which will help formulating GEOCAPE measurement requirements.

  12. A note on fixed point optimality criteria for the location problem with arbitrary norms: Reply

    DEFF Research Database (Denmark)

    Juel, Henrik; Love, Robert F.

    1983-01-01

    The single-facility location problem in continuous space is considered, with distances given by arbitrary norms. When distances are Euclidean, for many practical problems the optimal location of the new facility coincides with one of the existing facilities. This property carries over to problems...

  13. Analysis of point source size on measurement accuracy of lateral point-spread function of confocal Raman microscopy

    Science.gov (United States)

    Fu, Shihang; Zhang, Li; Hu, Yao; Ding, Xiang

    2018-01-01

    Confocal Raman Microscopy (CRM) has matured to become one of the most powerful instruments in analytical science because of its molecular sensitivity and high spatial resolution. Compared with conventional Raman Microscopy, CRM can perform three dimensions mapping of tiny samples and has the advantage of high spatial resolution thanking to the unique pinhole. With the wide application of the instrument, there is a growing requirement for the evaluation of the imaging performance of the system. Point-spread function (PSF) is an important approach to the evaluation of imaging capability of an optical instrument. Among a variety of measurement methods of PSF, the point source method has been widely used because it is easy to operate and the measurement results are approximate to the true PSF. In the point source method, the point source size has a significant impact on the final measurement accuracy. In this paper, the influence of the point source sizes on the measurement accuracy of PSF is analyzed and verified experimentally. A theoretical model of the lateral PSF for CRM is established and the effect of point source size on full-width at half maximum of lateral PSF is simulated. For long-term preservation and measurement convenience, PSF measurement phantom using polydimethylsiloxane resin, doped with different sizes of polystyrene microspheres is designed. The PSF of CRM with different sizes of microspheres are measured and the results are compared with the simulation results. The results provide a guide for measuring the PSF of the CRM.

  14. Monitoring Damage Using Acoustic Emission Source Location and Computational Geometry in Reinforced Concrete Beams

    Directory of Open Access Journals (Sweden)

    Jason Maximino C. Ongpeng

    2018-01-01

    Full Text Available Non-destructive testing in reinforced concrete (RC for damage detection is still limited to date. In monitoring the damage in RC, 18 beam specimens with varying water cement ratios and reinforcements were casted and tested using a four-point bending test. Repeated step loads were designed and at each step load acoustic emission (AE signals were recorded and processed to obtain the acoustic emission source location (AESL. Computational geometry using a convex hull algorithm was used to determine the maximum volume formed by the AESL inside the concrete beam in relation to the load applied. The convex hull volume (CHV showed good relation to the damage encountered until 60% of the ultimate load at the midspan was reached, where compression in the concrete occurred. The changes in CHV from 20 to 40% and 20 to 60% load were five and 13 times from CHV of 20% load for all beams, respectively. This indicated that the analysis in three dimensions using CHV was sensitive to damage. In addition, a high water-cement ratio exhibited higher CHV formation compared to a lower water-cement ratio due to its ductility where the movement of AESL becomes wider.

  15. Two-Dimensional Far Field Source Locating Method with Nonprior Velocity

    Directory of Open Access Journals (Sweden)

    Qing Chen

    2016-01-01

    Full Text Available Relative position of seismic source and sensors has great influence on locating accuracy, particularly in far field conditions, and the accuracy will decrease seriously due to limited calculation precision and prior velocity error. In order to improve the locating accuracy of far field sources by isometric placed sensors in a straight line, a new locating method with nonprior velocity is proposed. After exhaustive research, this paper states that the hyperbola which is used for locating will be very close to its asymptote when seismic source locates in far field of sensors; therefore, the locating problem with prior velocity is equivalent to solving linear equations and the problem with nonprior velocity is equivalent to a nonlinear optimization problem with respect to the unknown velocity. And then, this paper proposed a new locating method based on a one-variable objective function with respect to the unknown velocity. Numerical experiments show that the proposed method has faster convergence speed, higher accuracy, and better stability.

  16. Determining and modeling the dispersion of non point source ...

    African Journals Online (AJOL)

    In this study, pollutants in runoff are characterized and their dispersion after they enter the lake is measured and modeled at different points in the study areas. The objective is to develop a one dimensional mathematical model which can be used to predict the nutrient (ammonia, nitrite, nitrate, and phosphate) dispersion ...

  17. POINT CLOUD VISUALIZATION IN AN OPEN SOURCE 3D GLOBE

    Directory of Open Access Journals (Sweden)

    M. De La Calle

    2012-09-01

    Full Text Available During the last years the usage of 3D applications in GIS is becoming more popular. Since the appearance of Google Earth, users are familiarized with 3D environments. On the other hand, nowadays computers with 3D acceleration are common, broadband access is widespread and the public information that can be used in GIS clients that are able to use data from the Internet is constantly increasing. There are currently several libraries suitable for this kind of applications. Based on these facts, and using libraries that are already developed and connected to our own developments, we are working on the implementation of a real 3D GIS with analysis capabilities. Since a 3D GIS such as this can be very interesting for tasks like LiDAR or Laser Scanner point clouds rendering and analysis, special attention is given to get an optimal handling of very large data sets. Glob3 will be a multidimensional GIS in which 3D point clouds could be explored and analysed, even if they are consist of several million points.The latest addition to our visualization libraries is the development of a points cloud server that works regardless of the cloud's size. The server receives and processes petitions from a 3d client (for example glob3, but could be any other, such as one based on WebGL and delivers the data in the form of pre-processed tiles, depending on the required level of detail.

  18. Family of Quantum Sources for Improving Near Field Accuracy in Transducer Modeling by the Distributed Point Source Method

    Directory of Open Access Journals (Sweden)

    Dominique Placko

    2016-10-01

    Full Text Available The distributed point source method, or DPSM, developed in the last decade has been used for solving various engineering problems—such as elastic and electromagnetic wave propagation, electrostatic, and fluid flow problems. Based on a semi-analytical formulation, the DPSM solution is generally built by superimposing the point source solutions or Green’s functions. However, the DPSM solution can be also obtained by superimposing elemental solutions of volume sources having some source density called the equivalent source density (ESD. In earlier works mostly point sources were used. In this paper the DPSM formulation is modified to introduce a new kind of ESD, replacing the classical single point source by a family of point sources that are referred to as quantum sources. The proposed formulation with these quantum sources do not change the dimension of the global matrix to be inverted to solve the problem when compared with the classical point source-based DPSM formulation. To assess the performance of this new formulation, the ultrasonic field generated by a circular planer transducer was compared with the classical DPSM formulation and analytical solution. The results show a significant improvement in the near field computation.

  19. Contaminant point source localization error estimates as functions of data quantity and model quality.

    Science.gov (United States)

    Hansen, Scott K; Vesselinov, Velimir V

    2016-10-01

    We develop empirically-grounded error envelopes for localization of a point contamination release event in the saturated zone of a previously uncharacterized heterogeneous aquifer into which a number of plume-intercepting wells have been drilled. We assume that flow direction in the aquifer is known exactly and velocity is known to within a factor of two of our best guess from well observations prior to source identification. Other aquifer and source parameters must be estimated by interpretation of well breakthrough data via the advection-dispersion equation. We employ high performance computing to generate numerous random realizations of aquifer parameters and well locations, simulate well breakthrough data, and then employ unsupervised machine optimization techniques to estimate the most likely spatial (or space-time) location of the source. Tabulating the accuracy of these estimates from the multiple realizations, we relate the size of 90% and 95% confidence envelopes to the data quantity (number of wells) and model quality (fidelity of ADE interpretation model to actual concentrations in a heterogeneous aquifer with channelized flow). We find that for purely spatial localization of the contaminant source, increased data quantities can make up for reduced model quality. For space-time localization, we find similar qualitative behavior, but significantly degraded spatial localization reliability and less improvement from extra data collection. Since the space-time source localization problem is much more challenging, we also tried a multiple-initial-guess optimization strategy. This greatly enhanced performance, but gains from additional data collection remained limited. Copyright © 2016. Published by Elsevier B.V.

  20. Distributed Sensing for Quickest Change Detection of Point Radiation Sources

    Science.gov (United States)

    2017-02-01

    paper, we consider an architecture in which each sensor node makes a local binary decision based on current observations only, binary decisions are...quickest change-point detection using a sensor network. They consider non- parametric CUSUM tests at each sensor node without an explicit statistical model of...post-change distribution is unknown and modeled as member of parametric family, one can follow a generalized likelihood ratio based approach [8] or a

  1. Nomogram for Determining Shield Thickness for Point and Line Sources of Gamma Rays

    Energy Technology Data Exchange (ETDEWEB)

    Joenemalm, C.; Malen, K

    1966-10-15

    A set of nomograms is given for the determination of the required shield thickness against gamma radiation. The sources handled are point and infinite line sources with shields of Pb, Fe, magnetite concrete (p = 3.6), ordinary concrete (p = 2.3) or water. The gamma energy range covered is 0.5 - 10 MeV. The nomograms are directly applicable for source and dose points on the surfaces of the shield. They can easily be extended to source and dose points in other positions by applying a geometrical correction. Also included are data for calculation of the source strength for the most common materials and for fission product sources.

  2. Nomogram for Determining Shield Thickness for Point and Line Sources of Gamma Rays

    International Nuclear Information System (INIS)

    Joenemalm, C.; Malen, K

    1966-10-01

    A set of nomograms is given for the determination of the required shield thickness against gamma radiation. The sources handled are point and infinite line sources with shields of Pb, Fe, magnetite concrete (p = 3.6), ordinary concrete (p = 2.3) or water. The gamma energy range covered is 0.5 - 10 MeV. The nomograms are directly applicable for source and dose points on the surfaces of the shield. They can easily be extended to source and dose points in other positions by applying a geometrical correction. Also included are data for calculation of the source strength for the most common materials and for fission product sources

  3. Correlation of Earthquake Locations with Volumetric Source Components in TauTona Gold Mine, South Africa

    Science.gov (United States)

    Kane, D. L.; Boettcher, M. S.

    2013-12-01

    We investigate the source characteristics of earthquakes in TauTona Gold Mine, South Africa, to test if the location of earthquakes relative to mining structures is correlated with significant isotropic source behavior. Earthquakes are well monitored in TauTona Mine, where underground near-source stations record smaller events and higher frequency energy than can generally be observed using surface stations. Our dataset includes -4 mine, including faults, dikes, tunnels, and stopes, are well known from detailed geologic mapping and surveyed mine plans. We use data collected between 2004 and 2009 from the in-mine array (1-6 kHz), the Natural Earthquake Laboratory in South African Mines (NELSAM) project stations (6-12 kHz), and a short-term PASSCAL experiment (200 Hz) to study source mechanism variability and correlation with mapped structures within the mine. Previous studies of earthquakes in mines suggest a relationship between earthquake size and isotropic moment tensor source characteristics. In TauTona Mine, earthquakes with significant implosive source characteristics tend to be infrequent, larger events (Mw > 1.5), whereas earthquakes with significant explosive source characteristics tend to be smaller (Mw closure of tunnels and stopes within the mine, whereas the smallest recorded explosive events can be interpreted as opening cracks that form at the edges of mining structures. Double-couple type sources occur throughout the full magnitude range, and are often located along mapped faults and dikes. We focus our analysis on earthquakes located near the NELSAM stations in the deepest part of the mine, and on earthquakes located at depths greater than the current extent of mining. High precision relative hypocenter relocation performed using the 3-D extensive seismic array provides excellent constraints on location of events. We compute full moment tensor solutions for events using amplitude measurements of individual arrival phases, including nearfield phases

  4. Locating the Source of Atmospheric Contamination Based on Data From the Kori Field Tracer Experiment

    Directory of Open Access Journals (Sweden)

    Piotr Kopka

    2015-01-01

    Full Text Available Accidental releases of hazardous material into the atmosphere pose high risks to human health and the environment. Thus it would be valuable to develop an emergency reaction system which can recognize the probable location of the source based only on concentrations of the released substance as reported by a network of sensors. We apply a methodology combining Bayesian inference with Sequential Monte Carlo (SMC methods to the problem of locating the source of an atmospheric contaminant. The input data for this algorithm are the concentrations of a given substance gathered continuously in time. We employ this algorithm to locating a contamination source using data from a field tracer experiment covering the Kori nuclear site and conducted in May 2001. We use the second-order Closure Integrated PUFF Model (SCIPUFF of atmospheric dispersion as the forward model to predict concentrations at the sensors' locations. We demonstrate that the source of continuous contamination may be successfully located even in the very complicated, hilly terrain surrounding the Kori nuclear site. (original abstract

  5. Acoustic-emission source location using ''face-centered'' transducer arrays

    International Nuclear Information System (INIS)

    Hatano, Hajime; Hanajima, Takatoshi; Niwa, Noboru.

    1978-01-01

    A new method to locate the source of acoustic emission is introduced. Acoustic emission detectors are placed on a body to be investigated, and the signals from face-centered transducer arrays are analysed. Since the time-difference counter indicates directly the position of the source of acoustic emission, the source location system of real time can be constructed without any computer or peripheral instruments. The calculation of location is made by approximation, and the error due to the approximation is estimated. The upper limit of error is estimated to be 1.5 percent of lattice distance. Test experiment was performed with an aluminum plate, on which a steel ball was dropped and sound was generated. Experimental location was in good agreement with the theoretical location. The transmission loss of sound waves may be caused in some case, since the distance between the sound source and the detector is large in this method. However, it was found that this effect was negligible. The error due to the present method is less than the thickness of plates. The amount of error may be about one wave length of sound waves. (Kato, T.)

  6. Tokamak startup using point-source dc helicity injection.

    Science.gov (United States)

    Battaglia, D J; Bongard, M W; Fonck, R J; Redd, A J; Sontag, A C

    2009-06-05

    Startup of a 0.1 MA tokamak plasma is demonstrated on the ultralow aspect ratio Pegasus Toroidal Experiment using three localized, high-current density sources mounted near the outboard midplane. The injected open field current relaxes via helicity-conserving magnetic turbulence into a tokamaklike magnetic topology where the maximum sustained plasma current is determined by helicity balance and the requirements for magnetic relaxation.

  7. Calculated neutron dose rates and flux densities from implantable californium-252 point and line sources.

    Science.gov (United States)

    Shapiro, A; Schwartz, B; Windham, J P; Kereiakes, J G

    1976-01-01

    The results of neutron-transport flux-density and dose rate calculations for implantable Californium-252 point and line sources in essentially infinite tissue-equivalent material are presented. The point-source flux densities were obtained from a discrete ordinates calculation, and the point dose rates were established by multiplying the flux densities by their appropriate kerma factors. Line-source dose rates were evaluated by integrating the point dose rates over the length of the line source. Dose-rate data are given within a 20 X 20-cm region from the source center for source lengths of 1.5, 2, and 3 cm. The dose rates established by these calculations showed good agreement with an independent Monte Carlo calculation. Detailed point-source flux-density data as a function of energy and position are also given.

  8. My Precious! The Location and Diffusion of Scientific Research: Evidence from the Synchrotron Diamond Light Source

    OpenAIRE

    Christian Helmers; Henry Overman

    2013-01-01

    We analyze the impact of the establishment of a GBP 380 million basic scientific research facility in the UK on the geographical distribution of related research. We investigate whether the siting of the Diamond Light Source, a 3rd generation synchrotron light source, in Oxfordshire induced a clustering of related research in its geographic proximity. To account for the potentially endogenous location choice of the synchrotron, we exploit the availability of a `runner-up' site near Manchester...

  9. A METHOD FOR DETERMINING LOCATION OF VOLTAGE FLUCTUATIONS SOURCE IN ELECTRIC GRID

    Directory of Open Access Journals (Sweden)

    G.A. Senderovich

    2016-06-01

    Full Text Available Purpose. The purpose of work is development of a method of definition of the location of a source of fluctuations of voltage. Methodology. The reasons of emergence of fluctuations of voltage at an arrangement of a source both in power lines, and in the consumer's networks, are connected with changes of consumption and active and reactive capacities. As criterion for definition of the location of a source of fluctuations of voltage we choose change of size of the active power received by reception substation on equivalent communication with system. The source of fluctuations of voltage is external for the consumer if emergence of fluctuations of voltage leads to the coordinated changes of tension and consumed in the area of active power that corresponds to a condition of the positive regulating effect of active loading on voltage (1. The source of fluctuations of voltage is internal for the consumer if emergence of fluctuations of voltage leads to counter changes of tension and consumed in the area of active power that resembles a condition of the negative regulating effect of active loading on voltage superficially (6. Results. The method of definition of the location of a source of fluctuations of voltage in an electric network which, works by the principle of an assessment of correlation of change of power and tension in a power supply network is developed. The method allows to consider shift between extrema of curves of change of voltage of U(t and power of Pload(t. Originality. The method of definition of an arrangement of a source of fluctuations of voltage is developed. Practical value. The answer to this question where the source of fluctuations of voltage (in the territory of the consumer is located or in an external network confirmed with the determined calculation, can form a basis of the expert opinion for the solution of legal disputes at an assessment of the damages caused by poor quality of electric energy.

  10. Underwater Source-Level Estimation using Sparsity-Cognizant Source-Location Mapping

    Science.gov (United States)

    2014-12-01

    Capon [3]. It has also...single source. 6 0.0 0.2 0.4 0.6 0.8 1.0 % L oc al iz ed Time 55 60 65 70 75 80 85 |A co us tic S ou rc e G ai n| (d B) (a) Frequency = 65 Hz 0.0 0.2...0.4 0.6 0.8 1.0 % L oc al iz ed Time 55 60 65 70 75 80 85 |A co us tic S ou rc e G ai n| (d B) (b) Frequency = 150 Hz 0.0 0.2 0.4 0.6 0.8

  11. An automated multi-scale network-based scheme for detection and location of seismic sources

    Science.gov (United States)

    Poiata, N.; Aden-Antoniow, F.; Satriano, C.; Bernard, P.; Vilotte, J. P.; Obara, K.

    2017-12-01

    We present a recently developed method - BackTrackBB (Poiata et al. 2016) - allowing to image energy radiation from different seismic sources (e.g., earthquakes, LFEs, tremors) in different tectonic environments using continuous seismic records. The method exploits multi-scale frequency-selective coherence in the wave field, recorded by regional seismic networks or local arrays. The detection and location scheme is based on space-time reconstruction of the seismic sources through an imaging function built from the sum of station-pair time-delay likelihood functions, projected onto theoretical 3D time-delay grids. This imaging function is interpreted as the location likelihood of the seismic source. A signal pre-processing step constructs a multi-band statistical representation of the non stationary signal, i.e. time series, by means of higher-order statistics or energy envelope characteristic functions. Such signal-processing is designed to detect in time signal transients - of different scales and a priori unknown predominant frequency - potentially associated with a variety of sources (e.g., earthquakes, LFE, tremors), and to improve the performance and the robustness of the detection-and-location location step. The initial detection-location, based on a single phase analysis with the P- or S-phase only, can then be improved recursively in a station selection scheme. This scheme - exploiting the 3-component records - makes use of P- and S-phase characteristic functions, extracted after a polarization analysis of the event waveforms, and combines the single phase imaging functions with the S-P differential imaging functions. The performance of the method is demonstrated here in different tectonic environments: (1) analysis of the one year long precursory phase of 2014 Iquique earthquake in Chile; (2) detection and location of tectonic tremor sources and low-frequency earthquakes during the multiple episodes of tectonic tremor activity in southwestern Japan.

  12. MODELING OF AIR POLLUTION DISPERSION EMITTED FROM POINT SOURCES

    Directory of Open Access Journals (Sweden)

    Monika Wierzbińska

    2017-04-01

    Full Text Available In this paper, the modeling results of parameters and factors which determine spread of contamination in atmospheric air, are presented. These factors are: aerodynamic coefficient of area roughness, emitters location, exhaust temperature and velocity at the end of emitter. Computer program Ek100w calculates concentration of pollutants in the air on different distance from the emitter. We use calculation results to prepare charts with contour lines of air pollutions concentration. In this article contamination spread from emitters with different work parameters is analyzed. It follows that these parameters and factors have an important effect on contamination spreading in the atmospheric air. We can use such programs for emission design in practice and reduce impurities and immission on area where people are especially endanger for industrial emission.

  13. Humans use visual and remembered information about object location to plan pointing movements

    NARCIS (Netherlands)

    Brouwer, A.-M.; Knill, D.C.

    2009-01-01

    We investigated whether humans use a target's remembered location to plan reaching movements to targets according to the relative reliabilities of visual and remembered information. Using their index finger, subjects moved a virtual object from one side of a table to the other, and then went back to

  14. Instream Biological Assessment of NPDES Point Source Discharges at the Savannah River Site, 2000

    International Nuclear Information System (INIS)

    Specht, W.L.

    2001-01-01

    The Savannah River Site (SRS) currently has 31 NPDES outfalls that have been permitted by the South Carolina Department of Health and Environmental Control (SCDHEC) to discharge to SRS streams and the Savannah River. In order to determine the cumulative impacts of these discharges to the receiving streams, a study plan was developed to perform in-stream assessments of the fish assemblages, macroinvertebrate assemblages, and habitats of the receiving streams. These studies were designed to detect biological impacts due to point source discharges. Sampling was initially conducted between November 1997 and July 1998 and was repeated in the summer and fall of 2000. A total of 18 locations were sampled (Table 1, Figure 1). Sampling locations for fish and macroinvertebrates were generally the same. However, different locations were sampled for fish (Road A-2) and macroinvertebrates (Road C) in the lower portion of Upper Three Runs, to avoid interference with ongoing fisheries studies at Road C. Also, fish were sampled in Fourmile Branch at Road 4 rather than at Road F because the stream at Road F was too narrow and shallow to support many fish. Sampling locations and parameters are detailed in Sections 2 and 3 of this report. In general, sampling locations were selected that would permit comparisons upstream and downstream of NPDES outfalls. In instances where this approach was not feasible because effluents discharge into the headwaters of a stream, appropriate unimpacted reference were used for comparison purposes. This report summarizes the results of the sampling that was conducted in 2000 and also compares these data to the data that were collected in 1997 and 1998

  15. Industrial point source CO2 emission strength estimation with aircraft measurements and dispersion modelling.

    Science.gov (United States)

    Carotenuto, Federico; Gualtieri, Giovanni; Miglietta, Franco; Riccio, Angelo; Toscano, Piero; Wohlfahrt, Georg; Gioli, Beniamino

    2018-02-22

    CO 2 remains the greenhouse gas that contributes most to anthropogenic global warming, and the evaluation of its emissions is of major interest to both research and regulatory purposes. Emission inventories generally provide quite reliable estimates of CO 2 emissions. However, because of intrinsic uncertainties associated with these estimates, it is of great importance to validate emission inventories against independent estimates. This paper describes an integrated approach combining aircraft measurements and a puff dispersion modelling framework by considering a CO 2 industrial point source, located in Biganos, France. CO 2 density measurements were obtained by applying the mass balance method, while CO 2 emission estimates were derived by implementing the CALMET/CALPUFF model chain. For the latter, three meteorological initializations were used: (i) WRF-modelled outputs initialized by ECMWF reanalyses; (ii) WRF-modelled outputs initialized by CFSR reanalyses and (iii) local in situ observations. Governmental inventorial data were used as reference for all applications. The strengths and weaknesses of the different approaches and how they affect emission estimation uncertainty were investigated. The mass balance based on aircraft measurements was quite succesful in capturing the point source emission strength (at worst with a 16% bias), while the accuracy of the dispersion modelling, markedly when using ECMWF initialization through the WRF model, was only slightly lower (estimation with an 18% bias). The analysis will help in highlighting some methodological best practices that can be used as guidelines for future experiments.

  16. AKARI INFRARED CAMERA SURVEY OF THE LARGE MAGELLANIC CLOUD. I. POINT-SOURCE CATALOG

    International Nuclear Information System (INIS)

    Kato, Daisuke; Onaka, Takashi; Shimonishi, Takashi; Sakon, Itsuki; Ita, Yoshifusa; Tanabé, Toshihiko; Takahashi, Hidenori; Kaneda, Hidehiro; Kawamura, Akiko; Wada, Takehiko; Usui, Fumihiko; Koo, Bon-Chul; Matsuura, Mikako

    2012-01-01

    We present a near- to mid-infrared point-source catalog of five photometric bands at 3.2, 7, 11, 15, and 24 μm for a 10 deg 2 area of the Large Magellanic Cloud (LMC) obtained with the Infrared Camera on board the AKARI satellite. To cover the survey area the observations were carried out at three separate seasons from 2006 May to June, 2006 October to December, and 2007 March to July. The 10σ limiting magnitudes of the present survey are 17.9, 13.8, 12.4, 9.9, and 8.6 mag at 3.2, 7, 11, 15, and 24 μm, respectively. The photometric accuracy is estimated to be about 0.1 mag at 3.2 μm and 0.06-0.07 mag in the other bands. The position accuracy is 0.''3 at 3.2, 7, and 11 μm and 1.''0 at 15 and 24 μm. The sensitivities at 3.2, 7, and 24 μm are roughly comparable to those of the Spitzer SAGE LMC point-source catalog, while the AKARI catalog provides the data at 11 and 15 μm, covering the mid-infrared spectral range contiguously. Two types of catalog are provided: a Catalog and an Archive. The Archive contains all the detected sources, while the Catalog only includes the sources that have a counterpart in the Spitzer SAGE point-source catalog. The Archive contains about 650,000, 140,000, 97,000, 43,000, and 52,000 sources at 3.2, 7, 11, 15, and 24 μm, respectively. Based on the catalog, we discuss the luminosity functions at each band, the color-color diagram, and the color-magnitude diagram using the 3.2, 7, and 11 μm band data. Stars without circumstellar envelopes, dusty C-rich and O-rich stars, young stellar objects, and background galaxies are located at distinct regions in the diagrams, suggesting that the present catalog is useful for the classification of objects toward the LMC.

  17. Variation in the location of the shoe sole flexion point influences plantar loading patterns during gait

    NARCIS (Netherlands)

    van der Zwaard, B.C.; Vanwanseele, B.; Holtkamp, F.; van der Horst, H.E.; Elders, P.J.M.; Menz, H.B.

    2014-01-01

    Background: Several footwear design characteristics are known to have detrimental effects on the foot. However, one characteristic that has received relatively little attention is the point where the sole flexes in the sagittal plane. Several footwear assessment forms assume that this should ideally

  18. An iterated tabu search heuristic for the Single Source Capacitated Facility Location Problem

    DEFF Research Database (Denmark)

    Ho, Sin C.

    2015-01-01

    This paper discusses the Single Source Capacitated Facility Location Problem (SSCFLP) where the problem consists in determining a subset of capacitated facilities to be opened in order to satisfy the customers’ demands such that total costs are minimized. The paper presents an iterated tabu searc...... competitive with other metaheuristic approaches for solving the SSCFLP....

  19. A Procedure to Determine the Optimal Sensor Positions for Locating AE Sources in Rock Samples

    Science.gov (United States)

    Duca, S.; Occhiena, C.; Sambuelli, L.

    2015-03-01

    Within a research work aimed to better understand frost weathering mechanisms of rocks, laboratory tests have been designed to specifically assess a theoretical model of crack propagation due to ice segregation process in water-saturated and thermally microcracked cubic samples of Arolla gneiss. As the formation and growth of microcracks during freezing tests on rock material is accompanied by a sudden release of stored elastic energy, the propagation of elastic waves can be detected, at the laboratory scale, by acoustic emission (AE) sensors. The AE receiver array geometry is a sensitive factor influencing source location errors, for it can greatly amplify the effect of small measurement errors. Despite the large literature on the AE source location, little attention, to our knowledge, has been paid to the description of the experimental design phase. As a consequence, the criteria for sensor positioning are often not declared and not related to location accuracy. In the present paper, a tool for the identification of the optimal sensor position on a cubic shape rock specimen is presented. The optimal receiver configuration is chosen by studying the condition numbers of each of the kernel matrices, used for inverting the arrival time and finding the source location, and obtained for properly selected combinations between sensors and sources positions.

  20. An improved contour symmetry axes extraction algorithm and its application in the location of picking points of apples

    International Nuclear Information System (INIS)

    Wang, D.; Song, H.; Yu, X.; Zhang, W.; Qu, W.; Xu, Y.

    2015-01-01

    The key problem for picking robots is to locate the picking points of fruit. A method based on the moment of inertia and symmetry of apples is proposed in this paper to locate the picking points of apples. Image pre-processing procedures, which are crucial to improving the accuracy of the location, were carried out to remove noise and smooth the edges of apples. The moment of inertia method has the disadvantage of high computational complexity, which should be solved, so convex hull was used to improve this problem. To verify the validity of this algorithm, a test was conducted using four types of apple images containing 107 apple targets. These images were single and unblocked apple images, single and blocked apple images, images containing adjacent apples, and apples in panoramas. The root mean square error values of these four types of apple images were 6.3, 15.0, 21.6 and 18.4, respectively, and the average location errors were 4.9°, 10.2°, 16.3° and 13.8°, respectively. Furthermore, the improved algorithm was effective in terms of average runtime, with 3.7 ms and 9.2 ms for single and unblocked and single and blocked apple images, respectively. For the other two types of apple images, the runtime was determined by the number of apples and blocked apples contained in the images. The results showed that the improved algorithm could extract symmetry axes and locate the picking points of apples more efficiently. In conclusion, the improved algorithm is feasible for extracting symmetry axes and locating the picking points of apples. (Author)

  1. An improved contour symmetry axes extraction algorithm and its application in the location of picking points of apples

    Directory of Open Access Journals (Sweden)

    Dandan Wang

    2015-03-01

    Full Text Available The key problem for picking robots is to locate the picking points of fruit. A method based on the moment of inertia and symmetry of apples is proposed in this paper to locate the picking points of apples. Image pre-processing procedures, which are crucial to improving the accuracy of the location, were carried out to remove noise and smooth the edges of apples. The moment of inertia method has the disadvantage of high computational complexity, which should be solved, so convex hull was used to improve this problem. To verify the validity of this algorithm, a test was conducted using four types of apple images containing 107 apple targets. These images were single and unblocked apple images, single and blocked apple images, images containing adjacent apples, and apples in panoramas. The root mean square error values of these four types of apple images were 6.3, 15.0, 21.6 and 18.4, respectively, and the average location errors were 4.9°, 10.2°, 16.3° and 13.8°, respectively. Furthermore, the improved algorithm was effective in terms of average runtime, with 3.7 ms and 9.2 ms for single and unblocked and single and blocked apple images, respectively. For the other two types of apple images, the runtime was determined by the number of apples and blocked apples contained in the images. The results showed that the improved algorithm could extract symmetry axes and locate the picking points of apples more efficiently. In conclusion, the improved algorithm is feasible for extracting symmetry axes and locating the picking points of apples.

  2. An improved contour symmetry axes extraction algorithm and its application in the location of picking points of apples

    Energy Technology Data Exchange (ETDEWEB)

    Wang, D.; Song, H.; Yu, X.; Zhang, W.; Qu, W.; Xu, Y.

    2015-07-01

    The key problem for picking robots is to locate the picking points of fruit. A method based on the moment of inertia and symmetry of apples is proposed in this paper to locate the picking points of apples. Image pre-processing procedures, which are crucial to improving the accuracy of the location, were carried out to remove noise and smooth the edges of apples. The moment of inertia method has the disadvantage of high computational complexity, which should be solved, so convex hull was used to improve this problem. To verify the validity of this algorithm, a test was conducted using four types of apple images containing 107 apple targets. These images were single and unblocked apple images, single and blocked apple images, images containing adjacent apples, and apples in panoramas. The root mean square error values of these four types of apple images were 6.3, 15.0, 21.6 and 18.4, respectively, and the average location errors were 4.9°, 10.2°, 16.3° and 13.8°, respectively. Furthermore, the improved algorithm was effective in terms of average runtime, with 3.7 ms and 9.2 ms for single and unblocked and single and blocked apple images, respectively. For the other two types of apple images, the runtime was determined by the number of apples and blocked apples contained in the images. The results showed that the improved algorithm could extract symmetry axes and locate the picking points of apples more efficiently. In conclusion, the improved algorithm is feasible for extracting symmetry axes and locating the picking points of apples. (Author)

  3. A hybrid algorithm for stochastic single-source capacitated facility location problem with service level requirements

    Directory of Open Access Journals (Sweden)

    Hosseinali Salemi

    2016-04-01

    Full Text Available Facility location models are observed in many diverse areas such as communication networks, transportation, and distribution systems planning. They play significant role in supply chain and operations management and are one of the main well-known topics in strategic agenda of contemporary manufacturing and service companies accompanied by long-lasting effects. We define a new approach for solving stochastic single source capacitated facility location problem (SSSCFLP. Customers with stochastic demand are assigned to set of capacitated facilities that are selected to serve them. It is demonstrated that problem can be transformed to deterministic Single Source Capacitated Facility Location Problem (SSCFLP for Poisson demand distribution. A hybrid algorithm which combines Lagrangian heuristic with adjusted mixture of Ant colony and Genetic optimization is proposed to find lower and upper bounds for this problem. Computational results of various instances with distinct properties indicate that proposed solving approach is efficient.

  4. [A landscape ecological approach for urban non-point source pollution control].

    Science.gov (United States)

    Guo, Qinghai; Ma, Keming; Zhao, Jingzhu; Yang, Liu; Yin, Chengqing

    2005-05-01

    Urban non-point source pollution is a new problem appeared with the speeding development of urbanization. The particularity of urban land use and the increase of impervious surface area make urban non-point source pollution differ from agricultural non-point source pollution, and more difficult to control. Best Management Practices (BMPs) are the effective practices commonly applied in controlling urban non-point source pollution, mainly adopting local repairing practices to control the pollutants in surface runoff. Because of the close relationship between urban land use patterns and non-point source pollution, it would be rational to combine the landscape ecological planning with local BMPs to control the urban non-point source pollution, which needs, firstly, analyzing and evaluating the influence of landscape structure on water-bodies, pollution sources and pollutant removal processes to define the relationships between landscape spatial pattern and non-point source pollution and to decide the key polluted fields, and secondly, adjusting inherent landscape structures or/and joining new landscape factors to form new landscape pattern, and combining landscape planning and management through applying BMPs into planning to improve urban landscape heterogeneity and to control urban non-point source pollution.

  5. Revision of earthquake hypocentre locations in global bulletin data sets using source-specific station terms

    Science.gov (United States)

    Nooshiri, Nima; Saul, Joachim; Heimann, Sebastian; Tilmann, Frederik; Dahm, Torsten

    2017-02-01

    Global earthquake locations are often associated with very large systematic travel-time residuals even for clear arrivals, especially for regional and near-regional stations in subduction zones because of their strongly heterogeneous velocity structure. Travel-time corrections can drastically reduce travel-time residuals at regional stations and, in consequence, improve the relative location accuracy. We have extended the shrinking-box source-specific station terms technique to regional and teleseismic distances and adopted the algorithm for probabilistic, nonlinear, global-search location. We evaluated the potential of the method to compute precise relative hypocentre locations on a global scale. The method has been applied to two specific test regions using existing P- and pP-phase picks. The first data set consists of 3103 events along the Chilean margin and the second one comprises 1680 earthquakes in the Tonga-Fiji subduction zone. Pick data were obtained from the GEOFON earthquake bulletin, produced using data from all available, global station networks. A set of timing corrections varying as a function of source position was calculated for each seismic station. In this way, we could correct the systematic errors introduced into the locations by the inaccuracies in the assumed velocity structure without explicitly solving for a velocity model. Residual statistics show that the median absolute deviation of the travel-time residuals is reduced by 40-60 per cent at regional distances, where the velocity anomalies are strong. Moreover, the spread of the travel-time residuals decreased by ˜20 per cent at teleseismic distances (>28°). Furthermore, strong variations in initial residuals as a function of recording distance are smoothed out in the final residuals. The relocated catalogues exhibit less scattered locations in depth and sharper images of the seismicity associated with the subducting slabs. Comparison with a high-resolution local catalogue reveals that

  6. An algorithm to locate optimal bond breaking points on a potential energy surface for applications in mechanochemistry and catalysis

    Science.gov (United States)

    Bofill, Josep Maria; Ribas-Ariño, Jordi; García, Sergio Pablo; Quapp, Wolfgang

    2017-10-01

    The reaction path of a mechanically induced chemical transformation changes under stress. It is well established that the force-induced structural changes of minima and saddle points, i.e., the movement of the stationary points on the original or stress-free potential energy surface, can be described by a Newton Trajectory (NT). Given a reactive molecular system, a well-fitted pulling direction, and a sufficiently large value of the force, the minimum configuration of the reactant and the saddle point configuration of a transition state collapse at a point on the corresponding NT trajectory. This point is called barrier breakdown point or bond breaking point (BBP). The Hessian matrix at the BBP has a zero eigenvector which coincides with the gradient. It indicates which force (both in magnitude and direction) should be applied to the system to induce the reaction in a barrierless process. Within the manifold of BBPs, there exist optimal BBPs which indicate what is the optimal pulling direction and what is the minimal magnitude of the force to be applied for a given mechanochemical transformation. Since these special points are very important in the context of mechanochemistry and catalysis, it is crucial to develop efficient algorithms for their location. Here, we propose a Gauss-Newton algorithm that is based on the minimization of a positively defined function (the so-called σ -function). The behavior and efficiency of the new algorithm are shown for 2D test functions and for a real chemical example.

  7. Infrasonic source location imaging with the USArray: Application to one year of seismic data

    Science.gov (United States)

    Walker, K. T.; Shelby, R.; Hedlin, M. A.; Degroot-Hedlin, C. D.

    2010-12-01

    The USArray directly measures ground motion, which can mostly be attributed to ocean waves, earthquakes, volcanoes, and weather systems that load the Earth’s surface. Another source of ground motion is the transfer of atmospheric acoustic energy into seismic energy at the Earth’s surface. Infrasound (low frequency sound below ~20 Hz) can travel great distances unattenuated in atmospheric ducts. The infrasonic wave field is rich due to a variety of anthropogenic and geophysical phenomena including earthquakes, volcanoes, landslides, meteors, lightning and sprites, auroras, and oceanic and atmospheric processes. Globally spaced microbarometer arrays with apertures of 100 m to 2 km are typically used to study these sources. However, these arrays are separated by thousands of kilometers, which places considerable limits on what they can teach us about infrasound source physics. The USArray is in a position to study infrasound sources in unprecedented detail. Here we apply reverse-time migration to acoustic-to-seismic coupled signals recorded by the USArray to detect and locate in two-dimensional space and time several hundred infrasound sources in the western U.S. that occurred during 2008. Each event is visually inspected and assigned a quality rating. Confidence regions are determined using a bootstrap technique. The highest quality signals can be observed out to at least 1500 km range. We report the source location parameters for these events and investigate detection and location patterns. These results suggest that seismic networks near nuclear test monitoring infrasound arrays could be used to reduce the false alarm rate by identifying nearby, repeating sources of infrasound that create signals that are detected by the infrasound arrays. More fundamentally, these detected events comprise a ground truth database that can be used to validate or improve atmospheric velocity models.

  8. A point source solution for unidirectional flow of a viscoelastic fluid

    International Nuclear Information System (INIS)

    Momoniat, E.

    2008-01-01

    A Fourier point source solution modelling the effect of an impulse on a viscoelastic fluid of second-grade is investigated. By examining the second-moment of a Fourier point source solution we show that for Dt >1 the fluid undergoes classical diffusion indicating that the viscous properties of the fluid are dominating

  9. XID II: STATISTICAL CROSS-ASSOCIATION OF ROSAT BRIGHT SOURCE CATALOG X-RAY SOURCES WITH 2MASS POINT SOURCE CATALOG NEAR-INFRARED SOURCES

    International Nuclear Information System (INIS)

    Haakonsen, Christian Bernt; Rutledge, Robert E.

    2009-01-01

    The 18,806 ROSAT All Sky Survey Bright Source Catalog (RASS/BSC) X-ray sources are quantitatively cross-associated with near-infrared (NIR) sources from the Two Micron All Sky Survey Point Source Catalog (2MASS/PSC). An association catalog is presented, listing the most likely counterpart for each RASS/BSC source, the probability P id that the NIR source and X-ray source are uniquely associated, and the probability P no-id that none of the 2MASS/PSC sources are associated with the X-ray source. The catalog includes 3853 high quality (P id >0.98) X-ray-NIR matches, 2280 medium quality (0.98 ≥ P id >0.9) matches, and 4153 low quality (0.9 ≥ P id >0.5) matches. Of the high quality matches, 1418 are associations that are not listed in the SIMBAD database, and for which no high quality match with a USNO-A2 optical source was presented for the RASS/BSC source in previous work. The present work offers a significant number of new associations with RASS/BSC objects that will require optical/NIR spectroscopy for classification. For example, of the 6133 P id >0.9 2MASS/PSC counterparts presented in the association catalog, 2411 have no classification listed in the SIMBAD database. These 2MASS/PSC sources will likely include scientifically useful examples of known source classes of X-ray emitters (white dwarfs, coronally active stars, active galactic nuclei), but may also contain previously unknown source classes. It is determined that all coronally active stars in the RASS/BSC should have a counterpart in the 2MASS/PSC, and that the unique association of these RASS/BSC sources with their NIR counterparts thus is confusion limited.

  10. Simultaneous Determination of Source Wavelet and Velocity Profile Using Impulsive Point-Source Reflections from a Layered Fluid

    National Research Council Canada - National Science Library

    Bube, K; Lailly, P; Sacks, P; Santosa, F; Symes, W. W

    1987-01-01

    .... We show that a quasi-impulsive, isotropic point source may be recovered simultaneously with the velocity profile from reflection data over a layered fluid, in linear (perturbation) approximation...

  11. An Analytical Solution for Acoustic Emission Source Location for Known P Wave Velocity System

    Directory of Open Access Journals (Sweden)

    Longjun Dong

    2014-01-01

    Full Text Available This paper presents a three-dimensional analytical solution for acoustic emission source location using time difference of arrival (TDOA measurements from N receivers, N⩾5. The nonlinear location equations for TDOA are simplified to linear equations, and the direct analytical solution is obtained by solving the linear equations. There are not calculations of square roots in solution equations. The method solved the problems of the existence and multiplicity of solutions induced by the calculations of square roots in existed close-form methods. Simulations are included to study the algorithms' performance and compare with the existing technique.

  12. Transmission properties in a photonic crystal with a Dirac-like point located at the Brillouin zone center

    Science.gov (United States)

    Gao, H.; Zhou, Y.; Zhao, L.; Wei, G.

    2017-11-01

    Light transmission properties of a two-dimensional dielectric photonic crystal (PC) with a Dirac-like point located at the Brillouin zone center are studied. The results show that at the Dirac-like point, the transmittance remains constant rather than inversely varying with the PC's thickness, that is, this transmission does not follow the pseudo-diffusive phenomenon. Moreover, since the PC with a Dirac point at the Brillouin zone center can mimic zero index material (ZIM), transmittance of a real homogeneous ZIM layer is also theoretically investigated. Invariant transmittance is obtained again and the constant transmittance at the Dirac-like point is confirmed. Physical mechanisms of the pseudo-diffusive transmission as well as the constant transmission are both analyzed. It is found that the Dirac point is a critical state between band gaps and transmission bands, where the wave vector takes a complex number. It is the imaginary part of the wave vector which causes the decrease of the transmittance. While at the Dirac-like point at the center of the Brillouin zone, an additional flat band makes the Dirac point frequency fall into a transmission band where the wave vector is a real number, therefore the transmittance does not display any decrease tendency.

  13. Investigation of Light-Emitting Diode (LED) Point Light Source Color Visibility against Complex Multicolored Backgrounds

    Science.gov (United States)

    2017-11-01

    ARL-TR-8214 ● NOV 2017 US Army Research Laboratory Investigation of Light-Emitting Diode (LED) Point Light Source Color...ARL-TR-8214 ● NOV 2017 US Army Research Laboratory Investigation of Light-Emitting Diode (LED) Point Light Source Color Visibility against...instructions, searching existing data sources , gathering and maintaining the data needed, and completing and reviewing the collection information. Send

  14. Identification of sources of aerosol particles in three locations in eastern Botswana

    Science.gov (United States)

    Chimidza, S.; Moloi, K.

    2000-07-01

    Airborne particles have been collected using a dichotomous virtual impactor at three different locations in the eastern part of Botswana: Serowe, Selibe-Phikwe, and Francistown. The particles were separated into two fractions (fine and coarse). Sampling at the three locations was done consecutively during the months of July and August, which are usually dry and stable. The sampling time for each sample was 12 hours during the day. For elemental composition, energy-dispersive x-ray fluorescence technique was used. Correlations and principal component analysis with varimax rotation were used to identify major sources of aerosol particles. In all the three places, soil was found to be the main source of aerosol particles. A copper-nickel mine and smelter at Selibe-Phikwe was found to be not only a source of copper and nickel particles in Selibe-Phikwe but also a source of these particles in far places like Serowe. In Selibe-Phikwe and Francistown, car exhaust was found to be the major source of fine particles of lead and bromine.

  15. Acoustic emission non-destructive testing of structures using source location techniques.

    Energy Technology Data Exchange (ETDEWEB)

    Beattie, Alan G.

    2013-09-01

    The technology of acoustic emission (AE) testing has been advanced and used at Sandia for the past 40 years. AE has been used on structures including pressure vessels, fire bottles, wind turbines, gas wells, nuclear weapons, and solar collectors. This monograph begins with background topics in acoustics and instrumentation and then focuses on current acoustic emission technology. It covers the overall design and system setups for a test, with a wind turbine blade as the object. Test analysis is discussed with an emphasis on source location. Three test examples are presented, two on experimental wind turbine blades and one on aircraft fire extinguisher bottles. Finally, the code for a FORTRAN source location program is given as an example of a working analysis program. Throughout the document, the stress is on actual testing of real structures, not on laboratory experiments.

  16. The use of permit markets for incorporating source location. The case of acid rain in Europe

    International Nuclear Information System (INIS)

    Steiner, U.; Tinggaard Svendsen, G.

    1997-01-01

    The paper shows that cost-effective involvement of the source location involves utmost difficulty in practice. Based on the RAINS model, it is recommended that source location should be ignored in a European market for SO 2 , as is the case in the US Acid Rain Program. The RAINS-model predicts a cost-saving of 37 percent but an average loss of 2 percent in ecological protection. To overcome this reduction in protection, we recommend that some of the large cost-savings should be reallocated in further overall reduction and that the countries suffering the most from introducing the permit-market should be compensated by receiving extra permits in the initial distribution. (au)

  17. Measuring the distance from saddle points and driving to locate them over quantum control landscapes

    International Nuclear Information System (INIS)

    Sun, Qiuyang; Riviello, Gregory; Rabitz, Herschel; Wu, Re-Bing

    2015-01-01

    Optimal control of quantum phenomena involves the introduction of a cost functional J to characterize the degree of achieving a physical objective by a chosen shaped electromagnetic field. The cost functional dependence upon the control forms a control landscape. Two theoretically important canonical cases are the landscapes associated with seeking to achieve either a physical observable or a unitary transformation. Upon satisfaction of particular assumptions, both landscapes are analytically known to be trap-free, yet possess saddle points at precise suboptimal J values. The presence of saddles on the landscapes can influence the effort needed to find an optimal field. As a foundation to future algorithm development and analyzes, we define metrics that identify the ‘distance’ from a given saddle based on the sufficient and necessary conditions for the existence of the saddles. Algorithms are introduced utilizing the metrics to find a control such that the dynamics arrive at a targeted saddle. The saddle distance metric and saddle-seeking methodology is tested numerically in several model systems. (paper)

  18. Travel-time source-specific station correction improves location accuracy

    Science.gov (United States)

    Giuntini, Alessandra; Materni, Valerio; Chiappini, Stefano; Carluccio, Roberto; Console, Rodolfo; Chiappini, Massimo

    2013-04-01

    Accurate earthquake locations are crucial for investigating seismogenic processes, as well as for applications like verifying compliance to the Comprehensive Test Ban Treaty (CTBT). Earthquake location accuracy is related to the degree of knowledge about the 3-D structure of seismic wave velocity in the Earth. It is well known that modeling errors of calculated travel times may have the effect of shifting the computed epicenters far from the real locations by a distance even larger than the size of the statistical error ellipses, regardless of the accuracy in picking seismic phase arrivals. The consequences of large mislocations of seismic events in the context of the CTBT verification is particularly critical in order to trigger a possible On Site Inspection (OSI). In fact, the Treaty establishes that an OSI area cannot be larger than 1000 km2, and its larger linear dimension cannot be larger than 50 km. Moreover, depth accuracy is crucial for the application of the depth event screening criterion. In the present study, we develop a method of source-specific travel times corrections based on a set of well located events recorded by dense national seismic networks in seismically active regions. The applications concern seismic sequences recorded in Japan, Iran and Italy. We show that mislocations of the order of 10-20 km affecting the epicenters, as well as larger mislocations in hypocentral depths, calculated from a global seismic network and using the standard IASPEI91 travel times can be effectively removed by applying source-specific station corrections.

  19. High-resolution and super stacking of time-reversal mirrors in locating seismic sources

    KAUST Repository

    Cao, Weiping

    2011-07-08

    Time reversal mirrors can be used to backpropagate and refocus incident wavefields to their actual source location, with the subsequent benefits of imaging with high-resolution and super-stacking properties. These benefits of time reversal mirrors have been previously verified with computer simulations and laboratory experiments but not with exploration-scale seismic data. We now demonstrate the high-resolution and the super-stacking properties in locating seismic sources with field seismic data that include multiple scattering. Tests on both synthetic data and field data show that a time reversal mirror has the potential to exceed the Rayleigh resolution limit by factors of 4 or more. Results also show that a time reversal mirror has a significant resilience to strong Gaussian noise and that accurate imaging of source locations from passive seismic data can be accomplished with traces having signal-to-noise ratios as low as 0.001. Synthetic tests also demonstrate that time reversal mirrors can sometimes enhance the signal by a factor proportional to the square root of the product of the number of traces, denoted as N and the number of events in the traces. This enhancement property is denoted as super-stacking and greatly exceeds the classical signal-to-noise enhancement factor of. High-resolution and super-stacking are properties also enjoyed by seismic interferometry and reverse-time migration with the exact velocity model. © 2011 European Association of Geoscientists & Engineers.

  20. Locating critical points on multi-dimensional surfaces by genetic algorithm: test cases including normal and perturbed argon clusters

    Science.gov (United States)

    Chaudhury, Pinaki; Bhattacharyya, S. P.

    1999-03-01

    It is demonstrated that Genetic Algorithm in a floating point realisation can be a viable tool for locating critical points on a multi-dimensional potential energy surface (PES). For small clusters, the standard algorithm works well. For bigger ones, the search for global minimum becomes more efficient when used in conjunction with coordinate stretching, and partitioning of the strings into a core part and an outer part which are alternately optimized The method works with equal facility for locating minima, local as well as global, and saddle points (SP) of arbitrary orders. The search for minima requires computation of the gradient vector, but not the Hessian, while that for SP's requires the information of the gradient vector and the Hessian, the latter only at some specific points on the path. The method proposed is tested on (i) a model 2-d PES (ii) argon clusters (Ar 4-Ar 30) in which argon atoms interact via Lennard-Jones potential, (iii) Ar mX, m=12 clusters where X may be a neutral atom or a cation. We also explore if the method could also be used to construct what may be called a stochastic representation of the reaction path on a given PES with reference to conformational changes in Ar n clusters.

  1. NOx emissions from large point sources: variability in ozone production, resulting health damages and economic costs

    International Nuclear Information System (INIS)

    Mauzerall, D.L.; Namsoug Kim

    2005-01-01

    We present a proof-of-concept analysis of the measurement of the health damage of ozone (O 3 ) produced from nitrogen oxides (NO x =NO+NO 2 ) emitted by individual large point sources in the eastern United States. We use a regional atmospheric model of the eastern United States, the Comprehensive Air quality Model with Extensions (CAMx), to quantify the variable impact that a fixed quantity of NO x emitted from individual sources can have on the downwind concentration of surface O 3 , depending on temperature and local biogenic hydrocarbon emissions. We also examine the dependence of resulting O 3 -related health damages on the size of the exposed population. The investigation is relevant to the increasingly widely used 'cap and trade' approach to NO x regulation, which presumes that shifts of emission over time and space, holding the total fixed over the course of the summer O 3 season, will have minimal effect on the environmental outcome. By contrast, we show that a shift of a unit of NO x emissions from one place or time to another could result in large changes in resulting health effects due to O 3 formation and exposure. We indicate how the type of modeling carried out here might be used to attach externality-correcting prices to emissions. Charging emitters fees that are commensurate with the damage caused by their NO x emissions would create an incentive for emitters to reduce emissions at times and in locations where they cause the largest damage. (author)

  2. Distinguishing dark matter from unresolved point sources in the Inner Galaxy with photon statistics

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Samuel K. [Princeton Center for Theoretical Science, Princeton University, 400 Jadwin Hall, Princeton, NJ, 08544 (United States); Lisanti, Mariangela [Department of Physics, Princeton University, Jadwin Hall, Princeton, NJ, 08544 (United States); Safdi, Benjamin R., E-mail: samuelkl@princeton.edu, E-mail: mlisanti@princeton.edu, E-mail: bsafdi@princeton.edu [Center for Theoretical Physics, Massachusetts Institute of Technology, 77 Massachusetts Ave., 6-304, Cambridge, MA, 02139 (United States)

    2015-05-01

    Data from the Fermi Large Area Telescope suggests that there is an extended excess of GeV gamma-ray photons in the Inner Galaxy. Identifying potential astrophysical sources that contribute to this excess is an important step in verifying whether the signal originates from annihilating dark matter. In this paper, we focus on the potential contribution of unresolved point sources, such as millisecond pulsars (MSPs). We propose that the statistics of the photons—in particular, the flux probability density function (PDF) of the photon counts below the point-source detection threshold—can potentially distinguish between the dark-matter and point-source interpretations. We calculate the flux PDF via the method of generating functions for these two models of the excess. Working in the framework of Bayesian model comparison, we then demonstrate that the flux PDF can potentially provide evidence for an unresolved MSP-like point-source population.

  3. Inference of Unresolved Point Sources at High Galactic Latitudes Using Probabilistic Catalogs

    Science.gov (United States)

    Daylan, Tansu; Portillo, Stephen K. N.; Finkbeiner, Douglas P.

    2017-04-01

    The detection of point sources in images is a fundamental operation in astrophysics, and is crucial for constraining population models of the underlying point sources or characterizing the background emission. Standard techniques fall short in the crowded-field limit, losing sensitivity to faint sources and failing to track their covariance with close neighbors. We construct a Bayesian framework to perform inference of faint or overlapping point sources. The method involves probabilistic cataloging, where samples are taken from the posterior probability distribution of catalogs consistent with an observed photon count map. In order to validate our method, we sample random catalogs of the gamma-ray sky in the direction of the North Galactic Pole (NGP) by binning the data in energy and point-spread function classes. Using three energy bins spanning 0.3-1, 1-3, and 3-10 GeV, we identify {270}-10+30 point sources inside a 40^\\circ × 40^\\circ region around the NGP above our point-source inclusion limit of 3× {10}-11 cm-2 s-1 sr-1 GeV-1 at the 1-3 GeV energy bin. Modeling the flux distribution as a power law, we infer the slope to be -{1.92}-0.05+0.07 and estimate the contribution of point sources to the total emission as {18}-2+2%. These uncertainties in the flux distribution are fully marginalized over the number as well as the spatial and spectral properties of the unresolved point sources. This marginalization allows a robust test of whether the apparently isotropic emission in an image is due to unresolved point sources or of truly diffuse origin.

  4. Measurement of acoustic characteristics of Japanese Buddhist temples in relation to sound source location and direction.

    Science.gov (United States)

    Soeta, Yoshiharu; Shimokura, Ryota; Kim, Yong Hee; Ohsawa, Tomohiro; Ito, Ken

    2013-05-01

    Although temples are important buildings in the Buddhist community, the acoustic quality has not been examined in detail. Buddhist monks change the location and direction according to the ceremony, and associated acoustical changes have not yet been examined scientifically. To discuss the desired acoustics of temples, it is necessary to know the acoustic characteristics appropriate for each phase of a ceremony. In this study, acoustic measurements were taken at various source locations and directions in Japanese temples. A directional loudspeaker was used as the source to provide vocal acoustic fields, and impulse responses were measured and analyzed. The speech transmission index was higher and the interaural cross-correlation coefficient was lower for the sound source directed toward the side wall than that directed toward the altar. This suggests that the change in direction improves speech intelligibility, and the asymmetric property of direct sound and complex reflections from the altar and side wall increases the apparent source width. The large and coupled-like structure of the altar of a Buddhist temple may have reinforced the reverberation components and the table in the altar, which is called the "syumidan," may have decreased binaural coherence.

  5. Tracking the MSL-SAM methane detection source location Through Mars Regional Atmospheric Modeling System (MRAMS)

    Science.gov (United States)

    Pla-García, Jorge

    2016-04-01

    1. Introduction: The putative in situ detection of methane by Sample Analysis at Mars (SAM) instrument suite on Curiosi-ty at Gale crater has garnered significant attention because of the potential implications for the presence of geological methane sources or indigenous Martian organisms [1, 2]. SAM reported detection of back-ground levels of atmospheric methane of mean value 0.69±0.25 parts per billion by volume (ppbv) at the 95% confidence interval (CI). Additionally, in four sequential measurements spanning a 60-sol period, SAM observed elevated levels of methane of 7.2±2.1 ppbv (95% CI), implying that Mars is episodically producing methane from an additional unknown source. There are many major unresolved questions regard-ing this detection: 1) What are the potential sources of the methane release? 2) What causes the rapid decrease in concentration? and 3) Where is the re-lease location? 4) How spatially extensive is the re-lease? 5) For how long is CH4 released? Regarding the first question, the source of methane, is so far not identified. It could be related with geo-logical process like methane release from clathrates [3], serpentinisation [4] and volcanism [5]; or due to biological activity from methanogenesis [6]. To answer the second question, the rapid decrease in concentration, it is important to note that the photo-chemical lifetime of methane is of order 100 years, much longer than the atmospheric mixing time scale, and thus the gas should tend to be well mixed except near a source or shortly after an episodic release. The observed spike of 7 ppb from the background of System (MRAMS). The model was focused on rover locations using nested grids with a spacing of 330 meters on the in-nermost grid that is centered over the landing [8, 9]. MRAMS is ideally suited for this investigation; the model is explicitly designed to simulate Mars' at-mospheric circulations at the mesoscale and smaller with realistic, high-resolution surface properties [10, 11

  6. Assessment of Economic Loss Caused by Agricultural Non-point Source Nutrient Loss

    OpenAIRE

    Fan, Liang-qian; Chen, Feng-hui

    2012-01-01

    Taking Zhejiang Province as an example, we use the JOHNES export coefficient model to estimate the total nitrogen (TN) and total phosphorus (TP) load of agricultural planting, livestock and poultry breeding and rural living non-point source in 2009. Based on the protection cost method in environmental economics, we quantitatively assess the economic loss caused by these three types of non-point source nutrient loss. The results show that in TN non-point source load, the load of land for plant...

  7. Inference of Dim Gamma-Ray Point Sources Using Probabilistic Catalogues

    Science.gov (United States)

    Daylan, Tansu; Portillo, Stephen K. N.; Finkbeiner, Douglas P.

    2016-07-01

    Poisson regression of the Fermi-LAT data in the inner Milky Way reveals an extended gamma-ray excess. The anomalous emission falls steeply away from the galactic center and has an energy spectrum that peaks at 1-2 GeV. An important question is whether the signal is coming from a collection of unresolved point sources, possibly recycled pulsars, or constitutes a truly diffuse emission component. Previous analyses have relied on non-Poissonian template fits or wavelet decomposition of the Fermi-LAT data, which find evidence for a population of dim point sources just below the 3FGL flux limit. In order to draw conclusions about a potentially dim population, we propose to sample from the catalog space of point sources, where the model dimensionality, i.e., the number of sources, is unknown. Although being a computationally expensive sampling problem, this approach allows us to infer the number, flux and radial distribution of the point sources consistent with the observed count data. Probabilistic cataloging is specifically useful in the crowded field limit, such as in the galactic disk, where the typical separation between point sources is comparable to the PSF. Using this approach, we recover the results of the deterministic Fermi-LAT 3FGL catalog, as well as sub-detection threshold information and fold the point source parameter degeneracies into the model-choice problem of whether an emission is coming from unresolved MSPs or dark matter annihilation.

  8. Risk-based prioritisation of point sources through assessment of the impact on a water supply

    DEFF Research Database (Denmark)

    Overheu, Niels D.; Tuxen, Nina; Troldborg, Mads

    2011-01-01

    vulnerability mapping, site-specific mass flux estimates on a local scale from all the sources, and 3-D catchment-scale fate and transport modelling. It handles sources at various knowledge levels and accounts for uncertainties. The tool estimates the impacts on the water supply in the catchment and provides......A large number of point sources threaten groundwater resources. A tool is presented which enables a uniform and transparent risk assessment and prioritisation of these point sources at the catchment scale with respect to the needs of further investigation or remediation. The tool integrates aquifer...

  9. User Modeling for Point-of-Interest Recommendations in Location-Based Social Networks: The State of the Art

    Directory of Open Access Journals (Sweden)

    Shudong Liu

    2018-01-01

    Full Text Available The rapid growth of location-based services (LBSs has greatly enriched people’s urban lives and attracted millions of users in recent years. Location-based social networks (LBSNs allow users to check-in at a physical location and share daily tips on points of interest (POIs with their friends anytime and anywhere. Such a check-in behavior can make daily real-life experiences spread quickly through the Internet. Moreover, such check-in data in LBSNs can be fully exploited to understand the basic laws of humans’ daily movement and mobility. This paper focuses on reviewing the taxonomy of user modeling for POI recommendations through the data analysis of LBSNs. First, we briefly introduce the structure and data characteristics of LBSNs, and then we present a formalization of user modeling for POI recommendations in LBSNs. Depending on which type of LBSNs data was fully utilized in user modeling approaches for POI recommendations, we divide user modeling algorithms into four categories: pure check-in data-based user modeling, geographical information-based user modeling, spatiotemporal information-based user modeling, and geosocial information-based user modeling. Finally, summarizing the existing works, we point out the future challenges and new directions in five possible aspects.

  10. Transport of perfluoroalkyl substances (PFAS) from an arctic glacier to downstream locations: implications for sources.

    Science.gov (United States)

    Kwok, Karen Y; Yamazaki, Eriko; Yamashita, Nobuyoshi; Taniyasu, Sachi; Murphy, Margaret B; Horii, Yuichi; Petrick, Gert; Kallerborn, Roland; Kannan, Kurunthachalam; Murano, Kentaro; Lam, Paul K S

    2013-03-01

    Perfluoroalkyl substances (PFAS) have been globally detected in various environmental matrices, yet their fate and transport to the Arctic is still unclear, especially for the European Arctic. In this study, concentrations of 17 PFAS were quantified in two ice cores (n=26), surface snow (n=9) and surface water samples (n=14) collected along a spatial gradient in Svalbard, Norway. Concentrations of selected ions (Na(+), SO4(2-), etc.) were also determined for tracing the origins and sources of PFAS. Perfluorobutanoate (PFBA), perfluorooctanoate (PFOA) and perfluorononanoate (PFNA) were the dominant compounds found in ice core samples. Taking PFOA, PFNA and perfluorooctane-sulfonate (PFOS) as examples, higher concentrations were detected in the middle layers of the ice cores representing the period of 1997-2000. Lower concentrations of C8-C12 perfluorocarboxylates (PFCAs) were detected in comparison with concentrations measured previously in an ice core from the Canadian Arctic, indicating that contamination levels in the European Arctic are lower. Average PFAS concentrations were found to be lower in surface snow and melted glacier water samples, while increased concentrations were observed in river water downstream near the coastal area. Perfluorohexanesulfonate (PFHxS) was detected in the downstream locations, but not in the glacier, suggesting existence of local sources of this compound. Long-range atmospheric transport of PFAS was the major deposition pathway for the glaciers, while local sources (e.g., skiing activities) were identified in the downstream locations. Copyright © 2012 Elsevier B.V. All rights reserved.

  11. The 100 strongest radio point sources in the field of the Large Magellanic Cloud at 1.4 GHz

    Directory of Open Access Journals (Sweden)

    Payne J.L.

    2009-01-01

    Full Text Available We present the 100 strongest 1.4 GHz point sources from a new mosaic image in the direction of the Large Magellanic Cloud (LMC. The observations making up the mosaic were made using Australia Telescope Compact Array (ATCA over a ten year period and were combined with Parkes single dish data at 1.4 GHz to complete the image for short spacing. An initial list of co-identifications within 1000 at 0.843, 4.8 and 8.6 GHz consisted of 2682 sources. Elimination of extended objects and artifact noise allowed the creation of a refined list containing 1988 point sources. Most of these are presumed to be background objects seen through the LMC; a small portion may represent compact H ii regions, young SNRs and radio planetary nebulae. For the 1988 point sources we find a preliminary average spectral index (α of -0.53 and present a 1.4 GHz image showing source location in the direction of the LMC.

  12. Regulation of Heterogenous Non-Point Sources of Pollution Under Imperfect Information, The

    OpenAIRE

    Richard Cabe; Joseph A. Herriges

    1990-01-01

    This paper discusses the rose of information structure (i.e., information cost, reliability, and distribution among agents) in the design of a regulatory mechanism for controlling non-point source pollution. An ambient concentration tax mechanism is examined for non-point source pollution with spatial transport among multiple zones. Imposition of the tax requires costly measurement of ambient concentrations in selected zones, and the selection of zones for measurement must be undertaken witho...

  13. Complex source point theory of paraxial and nonparaxial cosine-Gauss and Bessel-Gauss beams.

    Science.gov (United States)

    Sheppard, Colin J R

    2013-02-15

    It shown how cosine-Gauss and Bessel-Gauss beams can be generated using the complex source point theory. Paraxial beams are treated first. An analytic expression is derived for the nonparaxial cosine-Gaussian beam, based on the complex source point approach, and numerical results are presented to illustrate its behavior. A way to generate nonparaxial Bessel-Gauss beams is also indicated.

  14. Astronomers Detect Powerful Bursting Radio Source Discovery Points to New Class of Astronomical Objects

    Science.gov (United States)

    2005-03-01

    Astronomers at Sweet Briar College and the Naval Research Laboratory (NRL) have detected a powerful new bursting radio source whose unique properties suggest the discovery of a new class of astronomical objects. The researchers have monitored the center of the Milky Way Galaxy for several years and reveal their findings in the March 3, 2005 edition of the journal, “Nature”. This radio image of the central region of the Milky Way Galaxy holds a new radio source, GCRT J1745-3009. The arrow points to an expanding ring of debris expelled by a supernova. CREDIT: N.E. Kassim et al., Naval Research Laboratory, NRAO/AUI/NSF Principal investigator, Dr. Scott Hyman, professor of physics at Sweet Briar College, said the discovery came after analyzing some additional observations from 2002 provided by researchers at Northwestern University. “"We hit the jackpot!” Hyman said referring to the observations. “An image of the Galactic center, made by collecting radio waves of about 1-meter in wavelength, revealed multiple bursts from the source during a seven-hour period from Sept. 30 to Oct. 1, 2002 — five bursts in fact, and repeating at remarkably constant intervals.” Hyman, four Sweet Briar students, and his NRL collaborators, Drs. Namir Kassim and Joseph Lazio, happened upon transient emission from two radio sources while studying the Galactic center in 1998. This prompted the team to propose an ongoing monitoring program using the National Science Foundation’s Very Large Array (VLA) radio telescope in New Mexico. The National Radio Astronomy Observatory, which operates the VLA, approved the program. The data collected, laid the groundwork for the detection of the new radio source. “Amazingly, even though the sky is known to be full of transient objects emitting at X- and gamma-ray wavelengths,” NRL astronomer Dr. Joseph Lazio pointed out, “very little has been done to look for radio bursts, which are often easier for astronomical objects to produce

  15. Joint Source Location and Focal Mechanism Inversion: efficiency, accuracy and applications

    Science.gov (United States)

    Liang, C.; Yu, Y.

    2017-12-01

    The analysis of induced seismicity has become a common practice to evaluate the results of hydraulic fracturing treatment. Liang et al (2016) proposed a joint Source Scanning Algorithms (jSSA for short) to obtain microseismic events and focal mechanisms simultaneously. The jSSA is superior over traditional SSA in many aspects, but the computation cost is too significant to be applied in real time monitoring. In this study, we have developed several scanning schemas to reduce computation time. A multi-stage scanning schema is proved to be able to improve the efficiency significantly while also retain its accuracy. A series of tests have been carried out by using both real field data and synthetic data to evaluate the accuracy of the method and its dependence on noise level, source depths, focal mechanisms and other factors. The surface-based arrays have better constraints on horizontal location errors (0.5). For sources with varying rakes, dips, strikes and depths, the errors are mostly controlled by the partition of positive and negative polarities in different quadrants. More evenly partitioned polarities in different quadrants yield better results in both locations and focal mechanisms. Nevertheless, even with bad resolutions for some FMs, the optimized jSSA method can still improve location accuracies significantly. Based on much more densely distributed events and focal mechanisms, a gridded stress inversion is conducted to get a evenly distributed stress field. The full potential of the jSSA has yet to be explored in different directions, especially in earthquake seismology as seismic array becoming incleasingly dense.

  16. Characteristics of a multi-keV monochromatic point x-ray source ...

    Indian Academy of Sciences (India)

    Temporal, spatial and spectral characteristics of a multi-keV monochromatic point x-ray source based on vacuum diode with laser-produced plasma as cathode are presented. Electrons from a laser-produced aluminium plasma were accelerated towards a conical point tip titanium anode to generate K-shell x-ray radiation.

  17. Characteristics of a multi-keV monochromatic point x-ray source

    Indian Academy of Sciences (India)

    Temporal, spatial and spectral characteristics of a multi-keV monochromatic point x-ray source based on vacuum diode with laser-produced plasma as cathode are presented. Electrons from a laser-produced aluminium plasma were accelerated towards a conical point tip titanium anode to generate K-shell x-ray radiation.

  18. Characteristics of a multi-keV monochromatic point x-ray source ...

    Indian Academy of Sciences (India)

    point x-ray source based on vacuum diode with laser-produced plasma as cathode are presented. Electrons from a laser-produced aluminium plasma were accelerated towards a conical point tip titanium anode to generate .... of an arc of radius 13 cm with the anode tip at the centre. The first cassette covered an angular ...

  19. An improved cut-and-solve algorithm for the single-source capacitated facility location problem

    DEFF Research Database (Denmark)

    Gadegaard, Sune Lauth; Klose, Andreas; Nielsen, Lars Relund

    2017-01-01

    In this paper, we present an improved cut-and-solve algorithm for the single-source capacitated facility location problem. The algorithm consists of three phases. The first phase strengthens the integer program by a cutting plane algorithm to obtain a tight lower bound. The second phase uses a two......-level local branching heuristic to find an upper bound, and if optimality has not yet been established, the third phase uses the cut-and-solve framework to close the optimality gap. Extensive computational results are reported, showing that the proposed algorithm runs 10–80 times faster on average compared...

  20. Neural network AE source location apart from structure size and material

    Czech Academy of Sciences Publication Activity Database

    Chlada, Milan; Převorovský, Zdeněk; Blaháček, Michal

    2010-01-01

    Roč. 28, - (2010), s. 99-107 ISSN 0730-0050. [European Conference on Acoustic Emission Testing 2010 /29./. Vídeň, 08.09.2010-10.09.2010] R&D Projects: GA ČR(CZ) GAP104/10/1430; GA MPO(CZ) FR-TI1/274 Institutional research plan: CEZ:AV0Z20760514 Keywords : AE source location * artificial neural network * arrival time profiles Subject RIV: BI - Acoustics http://www.ndt.net/search/abstract.php3?AbsID=10828

  1. Mapping correlation of a simulated dark matter source and a point source in the gamma-ray sky - Oral Presentation

    Energy Technology Data Exchange (ETDEWEB)

    Gibson, Alexander [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-08-23

    In my research, I analyzed how two gamma-ray source models interact with one another when optimizing to fit data. This is important because it becomes hard to distinguish between the two point sources when they are close together or looking at low energy photons. The reason for the first is obvious, the reason why they become harder to distinguish at lower photon energies is the resolving power of the Fermi Gamma-Ray Space Telescope gets worse at lower energies. When the two point sources are highly correlated (hard to distinguish between), we need to change our method of statistical analysis. What I did was show that highly correlated sources have larger uncertainties associated with them, caused by an optimizer not knowing which point source’s parameters to optimize. I also mapped out where their is high correlation for 2 different theoretical mass dark matter point sources so that people analyzing them in the future knew where they had to use more sophisticated statistical analysis.

  2. Point-like radioactive source with multiple absorber capsules for evaluating PET scanners.

    Science.gov (United States)

    Hasegawa, Tomoyuki; Yoshida, Eiji; Sato, Yasushi; Oda, Keiichi; Wada, Yasuhiro; Yamada, Takahiro; Yamaya, Taiga; Murayama, Hideo; Saito, Kyoko

    2010-06-01

    Radioactive sources for evaluating sensitivity and uncertainty in the radioactivity measurements performed using PET scanners must be equipped with absorber materials that ensure the annihilation of positrons. Attenuation and scattering owing to the absorber materials produce uncertainty in the performance evaluation. The aim of this study is to propose a point-like radioactive source with multiple absorber capsules, for which evaluation can be independent of scatter and attenuation owing to the source absorbers. The point-like source consists of a small spherical radioactive part and a set of successively sized cylindrical aluminum absorber capsules. Data were collected for different total absorber thicknesses. By an extrapolation technique, the effects of the source absorbers were eliminated. Sensitivity and uncertainty in the radioactivity measurements of PET scanners were evaluated with this technique. Sensitivity and uncertainty of radioactivity measurement to the point-like radioactive source were evaluated successfully with this method. The proposed point-like radioactive source is useful for evaluating performance characteristics of PET scanners in a way that is independent of the effects of the source absorbers.

  3. Sensitivity of the Baikal neutrino telescope NT-200 to point sources of very high energy neutrinos

    International Nuclear Information System (INIS)

    Krabi, J.; Spiering, C.; Bugaev, E.V.; Klimushin, S.I.

    1991-12-01

    The sensitivity of the deep underwater muon and neutrino detector 'NT-200' in lake Baikal to point sources of extraterrestrial neutrinos is calculated. Results are given for different assumptions on the neutrino source spectrum and the reconstruction capabilities of the detector. (orig.)

  4. Model Predictive Control of Z-source Neutral Point Clamped Inverter

    DEFF Research Database (Denmark)

    Mo, Wei; Loh, Poh Chiang; Blaabjerg, Frede

    2011-01-01

    This paper presents Model Predictive Control (MPC) of Z-source Neutral Point Clamped (NPC) inverter. For illustration, current control of Z-source NPC grid-connected inverter is analyzed and simulated. With MPC’s advantage of easily including system constraints, load current, impedance network...

  5. Reconstruction of source location in a network of gravitational wave interferometric detectors

    International Nuclear Information System (INIS)

    Cavalier, Fabien; Barsuglia, Matteo; Bizouard, Marie-Anne; Brisson, Violette; Clapson, Andre-Claude; Davier, Michel; Hello, Patrice; Kreckelbergh, Stephane; Leroy, Nicolas; Varvella, Monica

    2006-01-01

    This paper deals with the reconstruction of the direction of a gravitational wave source using the detection made by a network of interferometric detectors, mainly the LIGO and Virgo detectors. We suppose that an event has been seen in coincidence using a filter applied on the three detector data streams. Using the arrival time (and its associated error) of the gravitational signal in each detector, the direction of the source in the sky is computed using a χ 2 minimization technique. For reasonably large signals (SNR>4.5 in all detectors), the mean angular error between the real location and the reconstructed one is about 1 deg. . We also investigate the effect of the network geometry assuming the same angular response for all interferometric detectors. It appears that the reconstruction quality is not uniform over the sky and is degraded when the source approaches the plane defined by the three detectors. Adding at least one other detector to the LIGO-Virgo network reduces the blind regions and in the case of 6 detectors, a precision less than 1 deg. on the source direction can be reached for 99% of the sky

  6. Point sources of emerging contaminants along the Colorado River Basin: Source water for the arid Southwestern United States

    Science.gov (United States)

    Jones-Lepp, Tammy L.; Sanchez, Charles; Alvarez, David A.; Wilson, Doyle C.; Taniguchi-Fu, Randi-Laurant

    2012-01-01

    Emerging contaminants (ECs) (e.g., pharmaceuticals, illicit drugs, personal care products) have been detected in waters across the United States. The objective of this study was to evaluate point sources of ECs along the Colorado River, from the headwaters in Colorado to the Gulf of California. At selected locations in the Colorado River Basin (sites in Colorado, Utah, Nevada, Arizona, and California), waste stream tributaries and receiving surface waters were sampled using either grab sampling or polar organic chemical integrative samplers (POCIS). The grab samples were extracted using solid-phase cartridge extraction (SPE), and the POCIS sorbents were transferred into empty SPEs and eluted with methanol. All extracts were prepared for, and analyzed by, liquid chromatography–electrospray-ion trap mass spectrometry (LC–ESI-ITMS). Log DOW values were calculated for all ECs in the study and compared to the empirical data collected. POCIS extracts were screened for the presence of estrogenic chemicals using the yeast estrogen screen (YES) assay. Extracts from the 2008 POCIS deployment in the Las Vegas Wash showed the second highest estrogenicity response. In the grab samples, azithromycin (an antibiotic) was detected in all but one urban waste stream, with concentrations ranging from 30 ng/L to 2800 ng/L. Concentration levels of azithromycin, methamphetamine and pseudoephedrine showed temporal variation from the Tucson WWTP. Those ECs that were detected in the main surface water channels (those that are diverted for urban use and irrigation along the Colorado River) were in the region of the limit-of-detection (e.g., 10 ng/L), but most were below detection limits.

  7. Application of distributed point source method (DPSM) to wave propagation in anisotropic media

    Science.gov (United States)

    Fooladi, Samaneh; Kundu, Tribikram

    2017-04-01

    Distributed Point Source Method (DPSM) was developed by Placko and Kundu1, as a technique for modeling electromagnetic and elastic wave propagation problems. DPSM has been used for modeling ultrasonic, electrostatic and electromagnetic fields scattered by defects and anomalies in a structure. The modeling of such scattered field helps to extract valuable information about the location and type of defects. Therefore, DPSM can be used as an effective tool for Non-Destructive Testing (NDT). Anisotropy adds to the complexity of the problem, both mathematically and computationally. Computation of the Green's function which is used as the fundamental solution in DPSM is considerably more challenging for anisotropic media, and it cannot be reduced to a closed-form solution as is done for isotropic materials. The purpose of this study is to investigate and implement DPSM for an anisotropic medium. While the mathematical formulation and the numerical algorithm will be considered for general anisotropic media, more emphasis will be placed on transversely isotropic materials in the numerical example presented in this paper. The unidirectional fiber-reinforced composites which are widely used in today's industry are good examples of transversely isotropic materials. Development of an effective and accurate NDT method based on these modeling results can be of paramount importance for in-service monitoring of damage in composite structures.

  8. Miniature x-ray point source for alignment and calibration of x-ray optics

    International Nuclear Information System (INIS)

    Price, R.H.; Boyle, M.J.; Glaros, S.S.

    1977-01-01

    A miniature x-ray point source of high brightness similar to that of Rovinsky, et al. is described. One version of the x-ray source is used to align the x-ray optics on the Argus and Shiva laser systems. A second version is used to determine the spatial and spectral transmission functions of the x-ray optics. The spatial and spectral characteristics of the x-ray emission from the x-ray point source are described. The physical constraints including size, intensity and thermal limitations, and useful lifetime are discussed. The alignment and calibration techniques for various x-ray optics and detector combinations are described

  9. [Spatial heterogeneity and classified control of agricultural non-point source pollution in Huaihe River Basin].

    Science.gov (United States)

    Zhou, Liang; Xu, Jian-Gang; Sun, Dong-Qi; Ni, Tian-Hua

    2013-02-01

    Agricultural non-point source pollution is of importance in river deterioration. Thus identifying and concentrated controlling the key source-areas are the most effective approaches for non-point source pollution control. This study adopts inventory method to analysis four kinds of pollution sources and their emissions intensity of the chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in 173 counties (cities, districts) in Huaihe River Basin. The four pollution sources include livestock breeding, rural life, farmland cultivation, aquacultures. The paper mainly addresses identification of non-point polluted sensitivity areas, key pollution sources and its spatial distribution characteristics through cluster, sensitivity evaluation and spatial analysis. A geographic information system (GIS) and SPSS were used to carry out this study. The results show that: the COD, TN and TP emissions of agricultural non-point sources were 206.74 x 10(4) t, 66.49 x 10(4) t, 8.74 x 10(4) t separately in Huaihe River Basin in 2009; the emission intensity were 7.69, 2.47, 0.32 t.hm-2; the proportions of COD, TN, TP emissions were 73%, 24%, 3%. The paper achieves that: the major pollution source of COD, TN and TP was livestock breeding and rural life; the sensitivity areas and priority pollution control areas among the river basin of non-point source pollution are some sub-basins of the upper branches in Huaihe River, such as Shahe River, Yinghe River, Beiru River, Jialu River and Qingyi River; livestock breeding is the key pollution source in the priority pollution control areas. Finally, the paper concludes that pollution type of rural life has the highest pollution contribution rate, while comprehensive pollution is one type which is hard to control.

  10. Guaranteed Unresolved Point Source Emission and the Gamma-ray Background

    International Nuclear Information System (INIS)

    Pavlidou, Vasiliki; Siegal-Gaskins, Jennifer M.; Brown, Carolyn; Fields, Brian D.; Olinto, Angela V.

    2007-01-01

    The large majority of EGRET point sources remain without an identified low-energy counterpart, and a large fraction of these sources are most likely extragalactic. Whatever the nature of the extragalactic EGRET unidentified sources, faint unresolved objects of the same class must have a contribution to the diffuse extragalactic gamma-ray background (EGRB). Understanding this component of the EGRB, along with other guaranteed contributions from known sources (blazars and normal galaxies), is essential if we are to use this emission to constrain exotic high-energy physics. Here, we follow an empirical approach to estimate whether the contribution of unresolved unidentified sources to the EGRB is likely to be important. Additionally, we discuss how upcoming GLAST observations of EGRET unidentified sources, their fainter counterparts, and the Galactic and extragalactic diffuse backgrounds, will shed light on the nature of the EGRET unidentified sources even without any positional association of such sources with low-energy counterparts

  11. Acoustic emission source location in plates using wavelet analysis and cross time frequency spectrum.

    Science.gov (United States)

    Mostafapour, A; Davoodi, S; Ghareaghaji, M

    2014-12-01

    In this study, the theories of wavelet transform and cross-time frequency spectrum (CTFS) are used to locate AE source with frequency-varying wave velocity in plate-type structures. A rectangular array of four sensors is installed on the plate. When an impact is generated by an artificial AE source such as Hsu-Nielsen method of pencil lead breaking (PLB) at any position of the plate, the AE signals will be detected by four sensors at different times. By wavelet packet decomposition, a packet of signals with frequency range of 0.125-0.25MHz is selected. The CTFS is calculated by the short-time Fourier transform of the cross-correlation between considered packets captured by AE sensors. The time delay is calculated when the CTFS reaches the maximum value and the corresponding frequency is extracted per this maximum value. The resulting frequency is used to calculate the group velocity of wave velocity in combination with dispersive curve. The resulted locating error shows the high precision of proposed algorithm. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Long Period (LP) volcanic earthquake source location at Merapi volcano by using dense array technics

    Science.gov (United States)

    Metaxian, Jean Philippe; Budi Santoso, Agus; Laurin, Antoine; Subandriyo, Subandriyo; Widyoyudo, Wiku; Arshab, Ghofar

    2015-04-01

    Since 2010, Merapi shows unusual activity compared to last decades. Powerful phreatic explosions are observed; some of them are preceded by LP signals. In the literature, LP seismicity is thought to be originated within the fluid, and therefore to be representative of the pressurization state of the volcano plumbing system. Another model suggests that LP events are caused by slow, quasi-brittle, low stress-drop failure driven by transient upper-edifice deformations. Knowledge of the spatial distribution of LP events is fundamental for better understanding the physical processes occurring in the conduit, as well as for the monitoring and the improvement of eruption forecasting. LP events recorded at Merapi have a spectral content dominated by frequencies between 0.8 and 3 Hz. To locate the source of these events, we installed a seismic antenna composed of 4 broadband CMG-6TD Güralp stations. This network has an aperture of 300 m. It is located on the site of Pasarbubar, between 500 and 800 m from the crater rim. Two multi-parameter stations (seismic, tiltmeter, S-P) located in the same area, equipped with broadband CMG-40T Güralp sensors may also be used to complete the data of the antenna. The source of LP events is located by using different approaches. In the first one, we used a method based on the measurement of the time delays between the early beginnings of LP events for each array receiver. The observed differences of time delays obtained for each pair of receivers are compared to theoretical values calculated from the travel times computed between grid nodes, which are positioned in the structure, and each receiver. In a second approach, we estimate the slowness vector by using MUSIC algorithm applied to 3-components data. From the slowness vector, we deduce the back-azimuth and the incident angle, which give an estimation of LP source depth in the conduit. This work is part of the Domerapi project funded by French Agence Nationale de la Recherche (https

  13. Extending the search for neutrino point sources with IceCube above the horizon.

    Science.gov (United States)

    Abbasi, R; Abdou, Y; Abu-Zayyad, T; Adams, J; Aguilar, J A; Ahlers, M; Andeen, K; Auffenberg, J; Bai, X; Baker, M; Barwick, S W; Bay, R; Bazo Alba, J L; Beattie, K; Beatty, J J; Bechet, S; Becker, J K; Becker, K-H; Benabderrahmane, M L; Berdermann, J; Berghaus, P; Berley, D; Bernardini, E; Bertrand, D; Besson, D Z; Bissok, M; Blaufuss, E; Boersma, D J; Bohm, C; Botner, O; Bradley, L; Braun, J; Breder, D; Carson, M; Castermans, T; Chirkin, D; Christy, B; Clem, J; Cohen, S; Cowen, D F; D'Agostino, M V; Danninger, M; Day, C T; De Clercq, C; Demirörs, L; Depaepe, O; Descamps, F; Desiati, P; de Vries-Uiterweerd, G; DeYoung, T; Díaz-Vélez, J C; Dreyer, J; Dumm, J P; Duvoort, M R; Edwards, W R; Ehrlich, R; Eisch, J; Ellsworth, R W; Engdegård, O; Euler, S; Evenson, P A; Fadiran, O; Fazely, A R; Feusels, T; Filimonov, K; Finley, C; Foerster, M M; Fox, B D; Franckowiak, A; Franke, R; Gaisser, T K; Gallagher, J; Ganugapati, R; Gerhardt, L; Gladstone, L; Goldschmidt, A; Goodman, J A; Gozzini, R; Grant, D; Griesel, T; Gross, A; Grullon, S; Gunasingha, R M; Gurtner, M; Ha, C; Hallgren, A; Halzen, F; Han, K; Hanson, K; Hasegawa, Y; Helbing, K; Herquet, P; Hickford, S; Hill, G C; Hoffman, K D; Homeier, A; Hoshina, K; Hubert, D; Huelsnitz, W; Hülss, J-P; Hulth, P O; Hultqvist, K; Hussain, S; Imlay, R L; Inaba, M; Ishihara, A; Jacobsen, J; Japaridze, G S; Johansson, H; Joseph, J M; Kampert, K-H; Kappes, A; Karg, T; Karle, A; Kelley, J L; Kemming, N; Kenny, P; Kiryluk, J; Kislat, F; Klein, S R; Knops, S; Kohnen, G; Kolanoski, H; Köpke, L; Koskinen, D J; Kowalski, M; Kowarik, T; Krasberg, M; Krings, T; Kroll, G; Kuehn, K; Kuwabara, T; Labare, M; Lafebre, S; Laihem, K; Landsman, H; Lauer, R; Lehmann, R; Lennarz, D; Lundberg, J; Lünemann, J; Madsen, J; Majumdar, P; Maruyama, R; Mase, K; Matis, H S; McParland, C P; Meagher, K; Merck, M; Mészáros, P; Meures, T; Middell, E; Milke, N; Miyamoto, H; Montaruli, T; Morse, R; Movit, S M; Nahnhauer, R; Nam, J W; Niessen, P; Nygren, D R; Odrowski, S; Olivas, A; Olivo, M; Ono, M; Panknin, S; Patton, S; Paul, L; Pérez de los Heros, C; Petrovic, J; Piegsa, A; Pieloth, D; Pohl, A C; Porrata, R; Potthoff, N; Price, P B; Prikockis, M; Przybylski, G T; Rawlins, K; Redl, P; Resconi, E; Rhode, W; Ribordy, M; Rizzo, A; Rodrigues, J P; Roth, P; Rothmaier, F; Rott, C; Roucelle, C; Rutledge, D; Ruzybayev, B; Ryckbosch, D; Sander, H-G; Sarkar, S; Schatto, K; Schlenstedt, S; Schmidt, T; Schneider, D; Schukraft, A; Schulz, O; Schunck, M; Seckel, D; Semburg, B; Seo, S H; Sestayo, Y; Seunarine, S; Silvestri, A; Slipak, A; Spiczak, G M; Spiering, C; Stamatikos, M; Stanev, T; Stephens, G; Stezelberger, T; Stokstad, R G; Stoufer, M C; Stoyanov, S; Strahler, E A; Straszheim, T; Sullivan, G W; Swillens, Q; Taboada, I; Tamburro, A; Tarasova, O; Tepe, A; Ter-Antonyan, S; Terranova, C; Tilav, S; Toale, P A; Tooker, J; Tosi, D; Turcan, D; van Eijndhoven, N; Vandenbroucke, J; Van Overloop, A; van Santen, J; Voigt, B; Walck, C; Waldenmaier, T; Wallraff, M; Walter, M; Wendt, C; Westerhoff, S; Whitehorn, N; Wiebe, K; Wiebusch, C H; Wiedemann, A; Wikström, G; Williams, D R; Wischnewski, R; Wissing, H; Woschnagg, K; Xu, C; Xu, X W; Yodh, G; Yoshida, S

    2009-11-27

    Point source searches with the IceCube neutrino telescope have been restricted to one hemisphere, due to the exclusive selection of upward going events as a way of rejecting the atmospheric muon background. We show that the region above the horizon can be included by suppressing the background through energy-sensitive cuts. This improves the sensitivity above PeV energies, previously not accessible for declinations of more than a few degrees below the horizon due to the absorption of neutrinos in Earth. We present results based on data collected with 22 strings of IceCube, extending its field of view and energy reach for point source searches. No significant excess above the atmospheric background is observed in a sky scan and in tests of source candidates. Upper limits are reported, which for the first time cover point sources in the southern sky up to EeV energies.

  14. Tackling non-point source water pollution in British Columbia: An action plan

    Energy Technology Data Exchange (ETDEWEB)

    1998-01-01

    Efforts to protect British Columbia water quality by regulating point discharges from municipal and industrial sources have generally been successful, and it is recognized that the major remaining cause of water pollution in the province is from non-point sources. These sources are largely unregulated and associated with urbanization, agriculture, and other forms of land development. The first part of this report reviews the provincial commitment to clean water, the effects of non-point-source (NPS) pollution, and the management of NPS in the province. Part 2 describes the main causes of NPS in British Columbia: Land development, agriculture, stormwater runoff, on-site sewage systems, forestry and range activities, atmospheric deposition, and boating/marine activities. Finally, it presents key components of the province's NPS action plan: Education and training, prevention at site, land use planning and co-ordination, assessment and reporting, economic incentives, legislation and regulation, and implementation.

  15. Extending the search for neutrino point sources with IceCube above the horizon

    Energy Technology Data Exchange (ETDEWEB)

    IceCube Collaboration; Abbasi, R.

    2009-11-20

    Point source searches with the IceCube neutrino telescope have been restricted to one hemisphere, due to the exclusive selection of upward going events as a way of rejecting the atmospheric muon background. We show that the region above the horizon can be included by suppressing the background through energy-sensitive cuts. This approach improves the sensitivity above PeV energies, previously not accessible for declinations of more than a few degrees below the horizon due to the absorption of neutrinos in Earth. We present results based on data collected with 22 strings of IceCube, extending its field of view and energy reach for point source searches. No significant excess above the atmospheric background is observed in a sky scan and in tests of source candidates. Upper limits are reported, which for the first time cover point sources in the southern sky up to EeV energies.

  16. Consumption of added sugars among US children and adults by food purchase location and food source.

    Science.gov (United States)

    Drewnowski, Adam; Rehm, Colin D

    2014-09-01

    The proposed changes to the Nutrition Facts Label by the US Food and Drug Administration will include information on added sugars for the first time. The objective was to evaluate the sources of added sugars in the diets of a representative sample of US children and adults by food purchase location and food source (eg, food group). This cross-sectional study among 31,035 children, adolescents, and adults aged ≥6 y from the 2003-2004, 2005-2006, 2007-2008, and 2009-2010 NHANES used data from a 24-h dietary recall to evaluate consumption of added sugars. Food locations of origin were identified as stores (supermarket or grocery store), quick-service restaurants/pizza (QSRs), full-service restaurants (FSRs), schools, and others (eg, vending machines or gifts). Added sugars consumption by food purchase location was evaluated by age, family income-to-poverty ratio, and race-ethnicity. Food group sources of added sugars were identified by using the National Cancer Institute food categories. Added sugars accounted for ∼14.1% of total dietary energy. Between 65% and 76% of added sugars came from stores, 6% and 12% from QSRs, and 4% and 6% from FSRs, depending on age. Older adults (aged ≥51 y) obtained a significantly greater proportion of added sugars from stores than did younger adults. Lower-income adults obtained a significantly greater proportion of added sugars from stores than did higher-income adults. Intake of added sugars did not vary by family income among children/adolescents. Soda and energy and sports drinks were the largest food group sources of added sugars (34.4%), followed by grain desserts (12.7%), fruit drinks (8.0%), candy (6.7%), and dairy desserts (5.6%). Most added sugars came from foods obtained from stores. The proposed changes to the Nutrition Facts Label should capture the bulk of added sugars in the US food supply, which suggests that the recommended changes have the potential to reduce added sugars consumption. © 2014 American Society

  17. The liver of wrasse - morphology and function as a mirror of point source chemical impact.

    Science.gov (United States)

    Broeg, Katja; Kaiser, Wiebke; Bahns, Sieglinde; Koehler, Angela

    2008-07-01

    Corkwing wrasse (Symphodus melops L.), a protogynous, non-migratory lipfish species, living close to rocky shores was chosen as an indicator species for the monitoring of biological effects of contaminants. Fish were caught by local fisherman at the Norwegian west coast in fjord sites within the framework of the EU BEEP project. The sites represented different point source impacts of (I) copper (a former copper mine), (II) polycyclic aromatic hydrocarbons (PAHs, aluminium smelter discharge), (III) formaldehyde plus PAHs (kelp-factory and influence of the aluminium smelter). Livers of wrasse were studied for histopathological alterations and compared to healthy livers of fish from a reference location. Besides liver morphology, different functional and metabolic parameters were measured to link pathological alterations to functional disorders. The integrity of the lysosomal compartment was tested by the assessment of lysosomal membrane stability (lys), and the accumulation of neutral lipids and lipofuscin. Activity and intracellular localisation of the NADPH-producing enzymes in the liver were assessed histochemically and measured by computer-assisted image analysis. Histopathological alterations were most severe at the site impacted by formaldehyde and PAHs. These findings were associated with highest tumor prevalence, lowest membrane stabilities in hepatocytes and highest accumulation rates of lipofuscin in the liver. The activities of the NADPH-producing enzymes phosphogluconate dehydrogenase (PGDH) and glucose-6-phosphate dehydrogenase (G6PDH) were significantly lower compared to unimpacted reference fish. Histopathological alterations showed clear differences dependent on the input source. Potential links between specific contaminant impact and functional and morphological disorders are discussed.

  18. Optoacoustic effect from a point source moving in a circular orbit

    Science.gov (United States)

    Bai, Wenyu; Diebold, Gerald J.

    2017-03-01

    The optoacoustic effect is almost invariably produced by intensity modulated radiation, typically from a pulsed or an amplitude modulated continuous source. Given the form of the wave equation that describes the production of sound from absorption of light, it is clear that steady sources of radiation that move in space in an absorbing medium can also generate acoustic waves. Here the properties of a point source of radiation that rotates in a plane at a constant angular frequency are discussed. The source is shown to generate a spiral wave pattern that contains both compressions and rarefactions.

  19. Why the Center-Point of Bridged Carbon Nanotube Length is the Most Mass Sensitive Location for Mass Attachment?

    DEFF Research Database (Denmark)

    Mehdipour, I; Barari, Amin

    2012-01-01

    The continuum mechanics method and a bending model were used to obtain the resonant frequencies of bridged single-walled carbon nanotubes (SWCNTs) with masses rigidly attached at various positions along the tube. The frequency response equations were derived using the Euler–Bernoulli theory....... The resonant frequency decreased as the mass was increased, and the mass sensitivity increased as the attachment position approached the center of the bridged tube. The validity and accuracy of the equations were compared to other mass sensor models described in the literature. These new sensor equations may...... be used to model the behavior of CNT-based biosensors with reasonable accuracy. As a result, center point of bridged carbon nanotube is the most sensitive location for mass attachment....

  20. Stress Tolerance Variations in Saccharomyces cerevisiae Strains from Diverse Ecological Sources and Geographical Locations.

    Directory of Open Access Journals (Sweden)

    Yan-Lin Zheng

    Full Text Available The budding yeast Saccharomyces cerevisiae is a platform organism for bioethanol production from various feedstocks and robust strains are desirable for efficient fermentation because yeast cells inevitably encounter stressors during the process. Recently, diverse S. cerevisiae lineages were identified, which provided novel resources for understanding stress tolerance variations and related shaping factors in the yeast. This study characterized the tolerance of diverse S. cerevisiae strains to the stressors of high ethanol concentrations, temperature shocks, and osmotic stress. The results showed that the isolates from human-associated environments overall presented a higher level of stress tolerance compared with those from forests spared anthropogenic influences. Statistical analyses indicated that the variations of stress tolerance were significantly correlated with both ecological sources and geographical locations of the strains. This study provides guidelines for selection of robust S. cerevisiae strains for bioethanol production from nature.

  1. Stress Tolerance Variations in Saccharomyces cerevisiae Strains from Diverse Ecological Sources and Geographical Locations.

    Science.gov (United States)

    Zheng, Yan-Lin; Wang, Shi-An

    2015-01-01

    The budding yeast Saccharomyces cerevisiae is a platform organism for bioethanol production from various feedstocks and robust strains are desirable for efficient fermentation because yeast cells inevitably encounter stressors during the process. Recently, diverse S. cerevisiae lineages were identified, which provided novel resources for understanding stress tolerance variations and related shaping factors in the yeast. This study characterized the tolerance of diverse S. cerevisiae strains to the stressors of high ethanol concentrations, temperature shocks, and osmotic stress. The results showed that the isolates from human-associated environments overall presented a higher level of stress tolerance compared with those from forests spared anthropogenic influences. Statistical analyses indicated that the variations of stress tolerance were significantly correlated with both ecological sources and geographical locations of the strains. This study provides guidelines for selection of robust S. cerevisiae strains for bioethanol production from nature.

  2. The January 2014 Northern Cuba Earthquake Sequence - Unusual Location and Unexpected Source Mechanism Variability

    Science.gov (United States)

    Braunmiller, J.; Thompson, G.; McNutt, S. R.

    2017-12-01

    On 9 January 2014, a magnitude Mw=5.1 earthquake occurred along the Bahamas-Cuba suture at the northern coast of Cuba revealing a surprising seismic hazard source for both Cuba and southern Florida where it was widely felt. Due to its location, the event and its aftershocks (M>3.5) were recorded only at far distances (300+ km) resulting in high-detection thresholds, low location accuracy, and limited source parameter resolution. We use three-component regional seismic data to study the sequence. High-pass filtered seismograms at the closest site in southern Florida are similar in character suggesting a relatively tight event cluster and revealing additional, smaller aftershocks not included in the ANSS or ISC catalogs. Aligning on the P arrival and low-pass filtering (T>10 s) uncovers a surprise polarity flip of the large amplitude surface waves on vertical seismograms for some aftershocks relative to the main shock. We performed regional moment tensor inversions of the main shock and its largest aftershocks using complete three-component seismograms from stations distributed throughout the region to confirm the mechanism changes. Consistent with the GCMT solution, we find an E-W trending normal faulting mechanism for the main event and for one immediate aftershock. Two aftershocks indicate E-W trending reverse faulting with essentially flipped P- and T-axes relative to the normal faulting events (and the same B-axes). Within uncertainties, depths of the two event families are indistinguishable and indicate shallow faulting (Cuba posing a potential hazard to Florida and the Bahamas.

  3. Multistart algorithms for MEG empirical data analysis reliably characterize locations and time courses of multiple sources.

    Science.gov (United States)

    Aine, C; Huang, M; Stephen, J; Christner, R

    2000-08-01

    We applied our newly developed Multistart algorithm (M. Huang et al., 1998, Electroencephalogr. Clin. Neurophysiol. 108, 32-44) to high signal-to-noise ratio (SNR) somatosensory responses and low SNR visual data to demonstrate the reliability of this analysis tool for determining source locations and time courses of empirical multisource neuromagnetic data. This algorithm performs a downhill simplex search hundreds to thousands of times with multiple, randomly selected initial starting parameters from within the head volume, in order to avoid problems of local minima. Two subjects participated in two studies: (1) somatosensory (left and right median nerves were stimulated using a square wave pulse of 0.2 ms duration) and (2) visual (small black and white bull's-eye patterns were presented to central and peripheral locations in four quadrants of the visual field). One subject participated in both of the studies mentioned above and in a third study (i.e., simultaneous somatosensory/visual stimulation). The best-fitting solutions were tightly clustered in high SNR somatosensory data and all dominant regions of activity could be identified in some instances by using a single model order (e.g., six dipoles) applied to a single interval of time (e.g., 15-250 ms) that captured the entire somatosensory response. In low SNR visual data, solutions were obtained from several different model orders and time intervals in order to capture the dominant activity across the entire visual response (e.g. , 60-300 ms). Our results demonstrate that Multistart MEG analysis procedures can localize multiple regions of activity and characterize their time courses in a reliable fashion. Sources for visual data were determined by comparing results across several different models, each of which was based on hundreds to thousands of different fits to the data.

  4. Estimation of Multiple Point Sources for Linear Fractional Order Systems Using Modulating Functions

    KAUST Repository

    Belkhatir, Zehor

    2017-06-28

    This paper proposes an estimation algorithm for the characterization of multiple point inputs for linear fractional order systems. First, using polynomial modulating functions method and a suitable change of variables the problem of estimating the locations and the amplitudes of a multi-pointwise input is decoupled into two algebraic systems of equations. The first system is nonlinear and solves for the time locations iteratively, whereas the second system is linear and solves for the input’s amplitudes. Second, closed form formulas for both the time location and the amplitude are provided in the particular case of single point input. Finally, numerical examples are given to illustrate the performance of the proposed technique in both noise-free and noisy cases. The joint estimation of pointwise input and fractional differentiation orders is also presented. Furthermore, a discussion on the performance of the proposed algorithm is provided.

  5. Phase space of positron trajectories exiting a charged particle source through a magnetic field point cusp

    International Nuclear Information System (INIS)

    Kiester, A.S.; Pacheco, J.L.; Ordonez, C.A.; Weathers, D.L.

    2014-01-01

    A configuration of magnetic fields using properties of cylindrically symmetric permanent magnets is presented as a candidate to produce a high purity charged particle source or trap. Cylindrically symmetric hollow permanent magnets produce magnetic field point cusps on the axis of symmetry. A magnetic field point cusp reflects all particles that lie outside a narrow region of phase space, a region dependent on particle kinetic energies and on the magnetic field intensity. An analysis of the phase space of positron trajectories entering and exiting a magnetic field point cusp is presented and quantified with respect to magnetic field intensity and particle kinetic energy. Preliminary experimental results support the use of point cusps for ion source applications

  6. Modelling the detachment dependence on strike point location in the small angle slot divertor (SAS) with SOLPS

    Science.gov (United States)

    Casali, Livia; Covele, Brent; Guo, Houyang

    2017-10-01

    The new Small Angle Slot (SAS) divertor in DIII-D is characterized by a shallow-angle target enclosed by a slot structure about the strike point (SP). SOLPS modelling results of SAS have demonstrated divertor closure's utility in widening the range of acceptable densities for adequate heat handling. An extensive database of runs has been built to study the detachment dependence on SP location in SAS. Density scans show that lower Te at lower upstream density occur when the SP is at the critical location in the slot. The cooling front spreads across the entire target at higher densities, in agreement with experimental Langmuir probe measurements. A localized increase of the atomic and molecular density takes place near the SP, which reduces the target incident power density and facilitates detachment at lower upstream density. Systematic scans of variables such as power, transport, and viscosity have been carried out to assess the detachment sensitivity. Therein, a positive role of the viscosity is found. This work supported by DOE Contract Number DE-FC02-04ER54698.

  7. Developing a GIS-Based Model to Track Potential Point and Non-Point Sources of Urban Stream Pollution

    Science.gov (United States)

    Day, C. A.

    2014-12-01

    Urban streams are often characterized by diminished water quality resulting from an increase in polluted runoff from impervious surfaces. Storm activity further reduces urban stream water quality by temporarily increasing stormwater discharge from sewer overflows. This will often manifest itself in rapid declines of dissolved oxygen and peaks in specific conductivity in response to a rising biochemical oxygen demand which slowly recovers as the pollution load is washed through the stream system. This research developed a GIS-based model to track potential sources of pollution based on the dissolved oxygen and specific conductivity response of urban streams to a series of storm events, within the city of Louisville, Kentucky. Watershed outlet hydrographs were first obtained to determine the lag time of dissolved oxygen drops and specific conductivity peaks in response to set of storm events. Using a digital elevation model and the National Landcover Database, 10m resolution rasters were then created which calculated slope and flow direction/accumulation for both open channel and overland flow conditions across the watersheds. The rasters were merged and converted to flow velocities using a series of storms with different intensities. The final step utilized the Flow Length tool in ArcGIS which calculated the travel time to the watershed outlets from each pixel weighted by the open channel and overland flow conditions. Potential pollution sources could then be located by matching the dissolved oxygen and specific conductivity response lag times to the associated watershed travel times.

  8. PSFGAN: a generative adversarial network system for separating quasar point sources and host galaxy light

    Science.gov (United States)

    Stark, Dominic; Launet, Barthelemy; Schawinski, Kevin; Zhang, Ce; Koss, Michael; Turp, M. Dennis; Sartori, Lia F.; Zhang, Hantian; Chen, Yiru; Weigel, Anna K.

    2018-03-01

    The study of unobscured active galactic nuclei (AGN) and quasars depends on the reliable decomposition of the light from the AGN point source and the extended host galaxy light. The problem is typically approached using parametric fitting routines using separate models for the host galaxy and the point spread function (PSF). We present a new approach using a Generative Adversarial Network (GAN) trained on galaxy images. We test the method using Sloan Digital Sky Survey (SDSS) r-band images with artificial AGN point sources added which are then removed using the GAN and with parametric methods using GALFIT. When the AGN point source PS is more than twice as bright as the host galaxy, we find that our method, PSFGAN, can recover PS and host galaxy magnitudes with smaller systematic error and a lower average scatter (49%). PSFGAN is more tolerant to poor knowledge of the PSF than parametric methods. Our tests show that PSFGAN is robust against a broadening in the PSF width of ±50% if it is trained on multiple PSF's. We demonstrate that while a matched training set does improve performance, we can still subtract point sources using a PSFGAN trained on non-astronomical images. While initial training is computationally expensive, evaluating PSFGAN on data is more than 40 times faster than GALFIT fitting two components. Finally, PSFGAN it is more robust and easy to use than parametric methods as it requires no input parameters.

  9. Probing dim point sources in the inner Milky Way using PCAT

    Science.gov (United States)

    Daylan, Tansu; Portillo, Stephen K. N.; Finkbeiner, Douglas P.

    2017-01-01

    Poisson regression of the Fermi-LAT data in the inner Milky Way reveals an extended gamma-ray excess. An important question is whether the signal is coming from a collection of unresolved point sources, possibly old recycled pulsars, or constitutes a truly diffuse emission component. Previous analyses have relied on non-Poissonian template fits or wavelet decomposition of the Fermi-LAT data, which find evidence for a population of dim point sources just below the 3FGL flux limit. In order to be able to draw conclusions about the flux distribution of point sources at the dim end, we employ a Bayesian trans-dimensional MCMC framework by taking samples from the space of catalogs consistent with the observed gamma-ray emission in the inner Milky Way. The software implementation, PCAT (Probabilistic Cataloger), is designed to efficiently explore that catalog space in the crowded field limit such as in the galactic plane, where the model PSF, point source positions and fluxes are highly degenerate. We thus generate fair realizations of the underlying MSP population in the inner galaxy and constrain the population characteristics such as the radial and flux distribution of such sources.

  10. Location of the source of magnetospheric energetic particle bursts by multispacecraft observations

    International Nuclear Information System (INIS)

    Sarris, E.T.; Krimigis, S.M.; Iijima, T.; Bostrom, C.O.; Armstrong, T.P.

    1976-01-01

    During a magnetic substorm on October 16, 1973 a number of magnetospheric bursts of energetic particles were observed simultaneously by IMP-6 and IMP-7 in the magnetotail (at X/sub SM/approximately-greater-than-32 R/sub e/, Y/sub SM/approximately-greater-than1.2 R/sub e/ and Z/sub SM/SMapprox. =- 4.7 R/sub e/) while the two spacecraft were separated by only approx.1 R/sub e/ along the X/sub sM/ axis (deltaX/sub SM/approx. =1Re, deltaY/sub SM/=deltaZ/sub Sm/approx. = R/sub e/). Detailed anisotropy measurements of 210 and 290 keV protons by the JHU/APL instruments on both spacecraft provide for the first time an indication of the location of the ''source'' of the energetic magnetospheric particles as well as evidence for its movement with speeds from approx.30 to more than 80 km/sec in association with the intensification of the westward auroral electrojet during a magnetic bay at the station closest to the local time of the spacecraft (also local midnight). The size of the source was estimated to be degreeXapprox. =500 km. The observations indicate that in this case energetic particles are accelerated to >1.85 MeV in a moving and localized region in the geomagnetotail

  11. The Unicellular State as a Point Source in a Quantum Biological System

    Directory of Open Access Journals (Sweden)

    John S. Torday

    2016-05-01

    Full Text Available A point source is the central and most important point or place for any group of cohering phenomena. Evolutionary development presumes that biological processes are sequentially linked, but neither directed from, nor centralized within, any specific biologic structure or stage. However, such an epigenomic entity exists and its transforming effects can be understood through the obligatory recapitulation of all eukaryotic lifeforms through a zygotic unicellular phase. This requisite biological conjunction can now be properly assessed as the focal point of reconciliation between biology and quantum phenomena, illustrated by deconvoluting complex physiologic traits back to their unicellular origins.

  12. Evaluation of a non-point source pollution model, AnnAGNPS, in a tropical watershed

    Science.gov (United States)

    Polyakov, V.; Fares, A.; Kubo, D.; Jacobi, J.; Smith, C.

    2007-01-01

    Impaired water quality caused by human activity and the spread of invasive plant and animal species has been identified as a major factor of degradation of coastal ecosystems in the tropics. The main goal of this study was to evaluate the performance of AnnAGNPS (Annualized Non-Point Source Pollution Model), in simulating runoff and soil erosion in a 48 km2 watershed located on the Island of Kauai, Hawaii. The model was calibrated and validated using 2 years of observed stream flow and sediment load data. Alternative scenarios of spatial rainfall distribution and canopy interception were evaluated. Monthly runoff volumes predicted by AnnAGNPS compared well with the measured data (R2 = 0.90, P < 0.05); however, up to 60% difference between the actual and simulated runoff were observed during the driest months (May and July). Prediction of daily runoff was less accurate (R2 = 0.55, P < 0.05). Predicted and observed sediment yield on a daily basis was poorly correlated (R2 = 0.5, P < 0.05). For the events of small magnitude, the model generally overestimated sediment yield, while the opposite was true for larger events. Total monthly sediment yield varied within 50% of the observed values, except for May 2004. Among the input parameters the model was most sensitive to the values of ground residue cover and canopy cover. It was found that approximately one third of the watershed area had low sediment yield (0-1 t ha-1 y-1), and presented limited erosion threat. However, 5% of the area had sediment yields in excess of 5 t ha-1 y-1. Overall, the model performed reasonably well, and it can be used as a management tool on tropical watersheds to estimate and compare sediment loads, and identify "hot spots" on the landscape. ?? 2007 Elsevier Ltd. All rights reserved.

  13. 1SXPS: A DEEP SWIFT X-RAY TELESCOPE POINT SOURCE CATALOG WITH LIGHT CURVES AND SPECTRA

    International Nuclear Information System (INIS)

    Evans, P. A.; Osborne, J. P.; Beardmore, A. P.; Page, K. L.; Willingale, R.; Mountford, C. J.; Pagani, C.; Burrows, D. N.; Kennea, J. A.; Perri, M.; Tagliaferri, G.; Gehrels, N.

    2014-01-01

    We present the 1SXPS (Swift-XRT point source) catalog of 151,524 X-ray point sources detected by the Swift-XRT in 8 yr of operation. The catalog covers 1905 deg 2 distributed approximately uniformly on the sky. We analyze the data in two ways. First we consider all observations individually, for which we have a typical sensitivity of ∼3 × 10 –13  erg cm –2  s –1 (0.3-10 keV). Then we co-add all data covering the same location on the sky: these images have a typical sensitivity of ∼9 × 10 –14  erg cm –2  s –1 (0.3-10 keV). Our sky coverage is nearly 2.5 times that of 3XMM-DR4, although the catalog is a factor of ∼1.5 less sensitive. The median position error is 5.''5 (90% confidence), including systematics. Our source detection method improves on that used in previous X-ray Telescope (XRT) catalogs and we report >68, 000 new X-ray sources. The goals and observing strategy of the Swift satellite allow us to probe source variability on multiple timescales, and we find ∼30, 000 variable objects in our catalog. For every source we give positions, fluxes, time series (in four energy bands and two hardness ratios), estimates of the spectral properties, spectra and spectral fits for the brightest sources, and variability probabilities in multiple energy bands and timescales

  14. Loop Heat Pipe Operation Using Heat Source Temperature for Set Point Control

    Science.gov (United States)

    Ku, Jentung; Paiva, Kleber; Mantelli, Marcia

    2011-01-01

    The LHP operating temperature is governed by the saturation temperature of its reservoir. Controlling the reservoir saturation temperature is commonly accomplished by cold biasing the reservoir and using electrical heaters to provide the required control power. Using this method, the loop operating temperature can be controlled within +/- 0.5K. However, because of the thermal resistance that exists between the heat source and the LHP evaporator, the heat source temperature will vary with its heat output even if LHP operating temperature is kept constant. Since maintaining a constant heat source temperature is of most interest, a question often raised is whether the heat source temperature can be used for LHP set point temperature control. A test program with a miniature LHP has been carried out to investigate the effects on the LHP operation when the control temperature sensor is placed on the heat source instead of the reservoir. In these tests, the LHP reservoir is cold-biased and is heated by a control heater. Tests results show that it is feasible to use the heat source temperature for feedback control of the LHP operation. Using this method, the heat source temperature can be maintained within a tight range for moderate and high powers. At low powers, however, temperature oscillations may occur due to interactions among the reservoir control heater power, the heat source mass, and the heat output from the heat source. In addition, the heat source temperature could temporarily deviate from its set point during fast thermal transients. The implication is that more sophisticated feedback control algorithms need to be implemented for LHP transient operation when the heat source temperature is used for feedback control.

  15. KM3NeT/ARCA sensitivity and discovery potential for neutrino point-like sources

    Directory of Open Access Journals (Sweden)

    Trovato A.

    2016-01-01

    Full Text Available KM3NeT is a large research infrastructure with a network of deep-sea neutrino telescopes in the abyss of the Mediterranean Sea. Of these, the KM3NeT/ARCA detector, installed in the KM3NeT-It node of the network, is optimised for studying high-energy neutrinos of cosmic origin. Sensitivities to galactic sources such as the supernova remnant RXJ1713.7-3946 and the pulsar wind nebula Vela X are presented as well as sensitivities to a generic point source with an E−2 spectrum which represents an approximation for the spectrum of extragalactic candidate neutrino sources.

  16. Location, Location, Location!

    Science.gov (United States)

    Ramsdell, Kristin

    2004-01-01

    Of prime importance in real estate, location is also a key element in the appeal of romances. Popular geographic settings and historical periods sell, unpopular ones do not--not always with a logical explanation, as the author discovered when she conducted a survey on this topic last year. (Why, for example, are the French Revolution and the…

  17. Location, location, location

    NARCIS (Netherlands)

    Anderson, S.P.; Goeree, J.K.; Ramer, R.

    1997-01-01

    We analyze the canonical location-then-price duopoly game with general log- concave consumer densities. A unique pure-strategy equilibrium to the two-stage game exists if the density is not "too asymmetric" and not "too concave." These criteria are satisfied by many commonly used densities.

  18. Sound Spectrum Influences Auditory Distance Perception of Sound Sources Located in a Room Environment

    Directory of Open Access Journals (Sweden)

    Ignacio Spiousas

    2017-06-01

    Full Text Available Previous studies on the effect of spectral content on auditory distance perception (ADP focused on the physically measurable cues occurring either in the near field (low-pass filtering due to head diffraction or when the sound travels distances >15 m (high-frequency energy losses due to air absorption. Here, we study how the spectrum of a sound arriving from a source located in a reverberant room at intermediate distances (1–6 m influences the perception of the distance to the source. First, we conducted an ADP experiment using pure tones (the simplest possible spectrum of frequencies 0.5, 1, 2, and 4 kHz. Then, we performed a second ADP experiment with stimuli consisting of continuous broadband and bandpass-filtered (with center frequencies of 0.5, 1.5, and 4 kHz and bandwidths of 1/12, 1/3, and 1.5 octave pink-noise clips. Our results showed an effect of the stimulus frequency on the perceived distance both for pure tones and filtered noise bands: ADP was less accurate for stimuli containing energy only in the low-frequency range. Analysis of the frequency response of the room showed that the low accuracy observed for low-frequency stimuli can be explained by the presence of sparse modal resonances in the low-frequency region of the spectrum, which induced a non-monotonic relationship between binaural intensity and source distance. The results obtained in the second experiment suggest that ADP can also be affected by stimulus bandwidth but in a less straightforward way (i.e., depending on the center frequency, increasing stimulus bandwidth could have different effects. Finally, the analysis of the acoustical cues suggests that listeners judged source distance using mainly changes in the overall intensity of the auditory stimulus with distance rather than the direct-to-reverberant energy ratio, even for low-frequency noise bands (which typically induce high amount of reverberation. The results obtained in this study show that, depending on

  19. Search for cosmic neutrino point sources with four years of data from the ANTARES telescope

    NARCIS (Netherlands)

    Adrian-Martinez, S.; Al Samarai, I.; Albert, A.; Andre, M.; Anghinolfi, M.; Anton, G.; Anvar, S.; Ardid, M.; Astraatmadja, T.; Aubert, J.J.; Baret, B.; Basa, S.; Bertin, V.; Biagi, S.; Bigongiari, C.; Bogazzi, C.; Bou-Cabo, M.; Bouhou, B.; Bouwhuis, M.C.; Brunner, J.; Busto, J.; Capone, A.; Carloganu, C.; Carr, J.; Cecchini, S.; Charif, Z.; Charvis, P.; Chiarusi, T.; Circella, M.; Coniglione, R.; Core, L.; Costantini, H.; Coyle, P.; Creusot, A.; Curtil, C.; De Bonis, G.; Decowski, M.P.; Dekeyser, I.; Deschamps, A.; Distefano, C.; Donzaud, C.; Dornic, D.; Dorosti, Q.; Drouhin, D.; Eberl, T.; Emanuele, U.; Enzenhofer, A.; Ernenwein, J.P.; Escoffier, S.; Fehn, K.; Fermani, P.; Ferri, M.; Ferry, S.; Flaminio, V.; Folger, F.; Fritsch, U.; Fuda, J.L.; Galata, S.; Gay, P.; Geyer, K.; Giacomelli, G.; Giordano, V.; Gleixner, A.; Gomez-Gonzalez, J.P.; Graf, K.; Guillard, G.; Hallewell, G.; Hamal, M.; van Haren, H.; Heijboer, A.J.; Hello, Y.; Hernandez-Rey, J.J.; Herold, B.; Hossl, J.; Hsu, C.C.; De Jong, M.; Kadler, M.; Kalekin, O.; Kappes, A.; Katz, U.; Kavatsyuk, O.; Kooijman, P.; Kopper, C.; Kouchner, A.; Kreykenbohm, I.; Kulikovskiy, V.; Lahmann, R.; Lambard, G.; Larosa, G.; Lattuada, D.; Leonora, E.; Lefevre, D.; Lim, G.; Lo Presti, D.; Loehner, H.; Loucatos, S.; Louis, F.; Mangano, S.; Marcelin, M.; Margiotta, A.; Martinez-Mora, J.A.; Meli, A.; Montaruli, T.; Morganti, M.; Motz, H.; Neff, M.; Nezri, E.; Palioselitis, D.; Pavalas, G.E.; Payet, K.; Petrovic, J.; Piattelli, P.; Popa, V.; Pradier, T.; Presani, E.; Racca, C.; Reed, C.; Riccobene, G.; Richter, R.; Riviere, C.; Robert, A.; Roensch, K.; Rostovtsev, A.; Ruiz-Rivas, J.; Rujoiu, M.; Samtleben, D.F.E.; Sapienza, P.; Schmid, J.; Schnabel, J.; Schuller, J.P.; Schussler, F.; Seitz, T.; Shanidze, R.; Simeone, F.; Spies, A.; Spurio, M.; Steijger, J.J.M.; Stolarczyk, T.; Sanchez-Losa, A.; Taiuti, M.; Tamburini, C.; Trovato, A.; Vallage, B.; Vallee, C.; Van Elewyck, V.; Vecchi, M.; Vernin, P.; Visser, E.; Wagner, S.; Wijnker, G.; Wilms, J.; de Wolf, E.; Yepes, H.; Zaborov, D.; Zornoza, J.D.; Zuniga, J.

    2012-01-01

    In this paper, a time-integrated search for point sources of cosmic neutrinos is presented using the data collected from 2007 to 2010 by the ANTARES neutrino telescope. No statistically significant signal has been found and upper limits on the neutrino flux have been obtained. Assuming an E-nu(-2).

  20. Distributed Point Source Volcanism: A Mechanism for `Regional Plains' Resurfacing, Venus

    Science.gov (United States)

    Hansen, V. L.; Bleamaster, L. F., III

    2002-03-01

    V23/24 hosts shields that form a thin porous layer across >10x106 km2; variations in thermal gradient/conductivity, radioactive content/distribution, and surface T can result in time transgressive, incipient shallow point-source partial melting.

  1. Effect of tissue inhomogeneity on dose distribution of point sources of low-energy electrons

    International Nuclear Information System (INIS)

    Kwok, C.S.; Bialobzyski, P.J.; Yu, S.K.; Prestwich, W.V.

    1990-01-01

    Perturbation in dose distributions of point sources of low-energy electrons at planar interfaces of cortical bone (CB) and red marrow (RM) was investigated experimentally and by Monte Carlo codes EGS and the TIGER series. Ultrathin LiF thermoluminescent dosimeters were used to measure the dose distributions of point sources of 204 Tl and 147 Pm in RM. When the point sources were at 12 mg/cm 2 from a planar interface of CB and RM equivalent plastics, dose enhancement ratios in RM averaged over the region 0--12 mg/cm 2 from the interface were measured to be 1.08±0.03 (SE) and 1.03±0.03 (SE) for 204 Tl and 147 Pm, respectively. The Monte Carlo codes predicted 1.05±0.02 and 1.01±0.02 for the two nuclides, respectively. However, EGS gave consistently 3% higher dose in the dose scoring region than the TIGER series when point sources of monoenergetic electrons up to 0.75 MeV energy were considered in the homogeneous RM situation or in the CB and RM heterogeneous situation. By means of the TIGER series, it was demonstrated that aluminum, which is normally assumed to be equivalent to CB in radiation dosimetry, leads to an overestimation of backscattering of low-energy electrons in soft tissue at a CB--soft-tissue interface by as much as a factor of 2

  2. Estimation of Methane Emissions from Municipal Solid Waste Landfills in China Based on Point Emission Sources

    Directory of Open Access Journals (Sweden)

    Cai Bo-Feng

    2014-01-01

    Citation: Cai, B.-F., Liu, J.-G., Gao, Q.-X., et al., 2014. Estimation of methane emissions from municipal solid waste landfills in China based on point emission sources. Adv. Clim. Change Res. 5(2, doi: 10.3724/SP.J.1248.2014.081.

  3. Effect of varying dispenser point source density on mating disruption of Grapholita molesta (Lepidoptera: Tortricidae).

    Science.gov (United States)

    De Lame, Frédérique M; Epstein, David; Gut, Larry J; Goldfarb, Heidi; Miller, James R

    2010-08-01

    Hand-applied dispensers are successfully used in mating disruption programs, but cost of labor to apply these dispensers limits their adoption. Creating hand-applied dispensers that release larger amounts of pheromone and that can be applied at lower densities per hectare could reduce the cost of mating disruption and increase its use. The effect of reducing the number of point sources per hectare while keeping the amount of pheromone applied per hectare constant on the success of Grapholita molesta (Busck) (Lepidoptera: Tortricidae) mating disruption was investigated with Confuse-OFM, paraffin disk, and Isomate-M Rosso dispensers. For all dispensers, as point source density decreased, numbers of moths captured increased, percentage of orientation disruption to traps decreased, and variability in these measures increased. Decreasing point source density, even while keeping the amount of pheromone applied per hectare constant is not a viable option for reducing the cost of G. molesta mating disruption with hand-applied dispensers. Puffers (aerosol dispensers) are applied at 2.5-5 dispensers per ha for G. molesta control. However, hand-applied dispensers fail when clumped at such low numbers of release sites. Potential explanations for the success of Puffers and the failure of hand-applied dispensers at very low point source densities are presented. The utility of paraffin disk dispensers as experimental devices also is discussed.

  4. Applicability of a desiccant dew-point cooling system independent of external water sources

    DEFF Research Database (Denmark)

    Bellemo, Lorenzo; Elmegaard, Brian; Kærn, Martin Ryhl

    2015-01-01

    The applicability of a technical solution for making desiccant cooling systems independent of external water sources is investigated. Water is produced by condensing the desorbed water vapour in a closed regeneration circuit. Desorbed water recovery is applied to a desiccant dew-point cooling...

  5. General Approach to the Evolution of Singlet Nanoparticles from a Rapidly Quenched Point Source

    NARCIS (Netherlands)

    Feng, J.; Huang, Luyi; Ludvigsson, Linus; Messing, Maria; Maiser, A.; Biskos, G.; Schmidt-Ott, A.

    2016-01-01

    Among the numerous point vapor sources, microsecond-pulsed spark ablation at atmospheric pressure is a versatile and environmentally friendly method for producing ultrapure inorganic nanoparticles ranging from singlets having sizes smaller than 1 nm to larger agglomerated structures. Due to its fast

  6. Pollutant runoff from non-point sources and its estimation by runoff models.

    Science.gov (United States)

    Noguchi, M; Hiwatashi, T; Mizuno, Y; Minematsu, M

    2002-01-01

    In order to attain a sound and sustainable water environment, it is important to carry out the environmental management of the watershed. For this purpose, knowledge on the pollutant runoff mechanism from non-point sources becomes very important especially under rainy conditions. At Isahaya, Nagasaki, Japan, a big project of construction of sea-dyke and reclamation is now going on, so reducing the pollutant runoff, especially from non-point sources, becomes more important. Some runoff models of rainwater are developed to predict the rate of pollutant loads from the non-point sources, and their results are compared with each other to investigate the accuracy of prediction. In this paper, runoff analysis of both rainwater and pollutants has been carried out using three models: the tank model, the kinematic wave (K-W) model, and a model using the digital elevation model (DEM). For precise estimation, it becomes necessary to identify the parameters included in these models. Here, total nitrogen has been considered as pollutants, and detachment rates are evaluated, correlated with a class of land use, soil type, and moisture content. Finally, it has been shown that pollutant runoff from non-point sources can be predicted fairly well, identifying the model parameter appropriately.

  7. Temporal - spatial dynamics of vegetation variation on non - point source nutrient pollution

    NARCIS (Netherlands)

    Ouyang, Wei; Xuelei Wang,; Hao, Fanghua; Srinivasan, R.

    2009-01-01

    The temporal-spatial interaction of land cover and non-point source (NPS) nutrient pollution were analyzed with the Soil and Water Assessment Tool (SWAT) to simulate the temporal-spatial features of NPS nutrient loading in the upper stream of the Yellow River catchment. The corresponding land cover

  8. Agricultural non-point source pollution of glyphosate and AMPA at a catchment scale

    Science.gov (United States)

    Okada, Elena; Perez, Debora; De Geronimo, Eduardo; Aparicio, Virginia; Costa, Jose Luis

    2017-04-01

    Information on the actual input of pesticides into the environment is crucial for proper risk assessment and the design of risk reduction measures. The Crespo basin is found within the Balcarce County, located south-east of the Buenos Aires Province. The whole basin has an area of approximately 490 km2 and the river has a length of 65 km. This study focuses on the upper basin of the Crespo stream, covering an area of 226 km2 in which 94.7% of the land is under agricultural production representing a highly productive area, characteristic of the Austral Pampas region. In this study we evaluated the levels of glyphosate and its metabolite aminomethylphosphonic acid (AMPA) in soils; and the non-point source pollution of surface waters, stream sediments and groundwater, over a period of one year. Stream water samples were taken monthly using propylene bottles, from the center of the bridge. If present, sediment samples from the first 5 cm were collected using cylinder samplers. Groundwater samples were taken from windmills or electric pumps from different farms every two months. At the same time, composite soil samples (at 5 cm depth) were taken from an agricultural plot of each farm. Samples were analyzed for detection and quantification of glyphosate and AMPA using ultra-performance liquid chromatography coupled to a mass spectrometer (UPLC-MS/MS). The limit of detection (LD) in the soil samples was 0.5 μg Kg-1 and the limit of quantification (LQ) was 3 μg Kg-1, both for glyphosate and AMPA. In water samples the LD was 0.1 μg L-1 and the LQ was 0.5 μg L-1. The results showed that the herbicide dispersed into all the studied environmental compartments. Glyphosate and AMPA residues were detected in 34 and 54% of the stream water samples, respectively. Sediment samples had a higher detection frequency (>96%) than water samples, and there was no relationship between the presence in surface water with the detection in sediment samples. The presence in sediment samples

  9. Nanoscale structuring of tungsten tip yields most coherent electron point-source

    International Nuclear Information System (INIS)

    Mutus, Josh Y; Livadaru, Lucian; Urban, Radovan; Pitters, Jason; Peter Legg, A; Salomons, Mark H; Cloutier, Martin; Wolkow, Robert A

    2013-01-01

    This report demonstrates the most spatially-coherent electron source ever reported. A coherence angle of 14.3 ± 0.5° was measured, indicating a virtual source size of 1.7 ± 0.6 Å using an extraction voltage of 89.5 V. The nanotips under study were crafted using a spatially-confined, field-assisted nitrogen etch which removes material from the periphery of the tip apex resulting in a sharp, tungsten–nitride stabilized, high-aspect ratio source. The coherence properties are deduced from holographic measurements in a low-energy electron point source microscope with a carbon nanotube bundle as sample. Using the virtual source size and emission current the brightness normalized to 100 kV is found to be 7.9 × 10 8 A sr −1 cm 2 . (paper)

  10. Comparative Evaluation of Pulsewidth Modulation Strategies for Z-Source Neutral-Point-Clamped Inverter

    DEFF Research Database (Denmark)

    Loh, P.C.; Blaabjerg, Frede; Wong, C.P.

    2007-01-01

    Z-source neutral-point-clamped (NPC) inverter has recently been proposed as an alternative three-level buck-boost power conversion solution with an improved output waveform quality. In principle, the designed Z-source inverter functions by selectively "shooting through" its power sources, coupled...... to the inverter using two unique Z-source impedance networks, to boost the inverter three-level output waveform. Proper modulation of the new inverter would therefore require careful integration of the selective shoot-through process to the basic switching concepts to achieve maximal voltage-boost, minimal...... modulation (PWM) strategies for controlling the Z-source NPC inverter. While developing the PWM techniques, attention has been devoted to carefully derive them from a common generic basis for improved portability, easier implementation, and most importantly, assisting readers in understanding all concepts...

  11. Comparative Evaluation of Pulsewidth Modulation Strategies for Z-Source Neutral-Point-Clamped Inverter

    DEFF Research Database (Denmark)

    Loh, P.C.; Blaabjerg, Frede; Wong, C.P.

    2007-01-01

    modulation (PWM) strategies for controlling the Z-source NPC inverter. While developing the PWM techniques, attention has been devoted to carefully derive them from a common generic basis for improved portability, easier implementation, and most importantly, assisting readers in understanding all concepts......Z-source neutral-point-clamped (NPC) inverter has recently been proposed as an alternative three-level buck-boost power conversion solution with an improved output waveform quality. In principle, the designed Z-source inverter functions by selectively "shooting through" its power sources, coupled...... to the inverter using two unique Z-source impedance networks, to boost the inverter three-level output waveform. Proper modulation of the new inverter would therefore require careful integration of the selective shoot-through process to the basic switching concepts to achieve maximal voltage-boost, minimal...

  12. Near-field and high-resolution cylindrical noise source location method based on vector sound pressure array

    Directory of Open Access Journals (Sweden)

    ZUO Xiang

    2017-08-01

    Full Text Available The existing underwater noise source near-field location method usually assumes that the measurement plane is flat, which increases the difficulty of applying the underwater noise target test for cylindrical distribution. Simultaneously, the conventional near-field focused beam has a lower spatial resolution when used to locate an underwater noise source with cylindrical distribution. Moreover, the near-field underwater noise source location method based on the sound pressure array has a left and right side fuzzy problem. In order to solve these problems, by establishing the near-field measurement model of the noise source with cylindrical distribution as the measurement surface, and combining the unilateral directivity of the vector hydrophone and the high resolution characteristics of the MUSIC algorithm, a near-field and high resolution location method is proposed for cylindrical distribution based on vector sound pressure, and a computer simulation is carried out. The results show that the method can use a smaller array aperture to locate the underwater noise source, enabling it to be used to locate and recognize the noise sources of complex and large-scale cylindrical systems.

  13. IceCube results from point-like source searches using 6 years of through-going muon data

    Directory of Open Access Journals (Sweden)

    Coenders Stefan

    2016-01-01

    Full Text Available The IceCube Neutrino Observatory located at the geographic South Pole was designed to study and discover high energy neutrinos coming from both galactic and extra-galactic astrophysical sources. Track-like events induced by charged-current muon-neutrino interactions close to the IceCube detector give an angular resolution better than 1∘ above TeV energies. We present here the results of searches for point-like astrophysical neutrino sources on the full sky using 6 years of detector livetime, of which three years use the complete IceCube detector. Within 2000 days of detector livetime, IceCube is sensitive to a steady flux substantially below E2∂ϕ/∂E = 10−12 TeV cm−2 s−1 in the northern sky for neutrino energies above 10 TeV.

  14. The Potential for Electrofuels Production in Sweden Utilizing Fossil and Biogenic CO2 Point Sources

    International Nuclear Information System (INIS)

    Hansson, Julia; Hackl, Roman; Taljegard, Maria; Brynolf, Selma; Grahn, Maria

    2017-01-01

    This paper maps, categorizes, and quantifies all major point sources of carbon dioxide (CO 2 ) emissions from industrial and combustion processes in Sweden. The paper also estimates the Swedish technical potential for electrofuels (power-to-gas/fuels) based on carbon capture and utilization. With our bottom-up approach using European databases, we find that Sweden emits approximately 50 million metric tons of CO 2 per year from different types of point sources, with 65% (or about 32 million tons) from biogenic sources. The major sources are the pulp and paper industry (46%), heat and power production (23%), and waste treatment and incineration (8%). Most of the CO 2 is emitted at low concentrations (<15%) from sources in the southern part of Sweden where power demand generally exceeds in-region supply. The potentially recoverable emissions from all the included point sources amount to 45 million tons. If all the recoverable CO 2 were used to produce electrofuels, the yield would correspond to 2–3 times the current Swedish demand for transportation fuels. The electricity required would correspond to about 3 times the current Swedish electricity supply. The current relatively few emission sources with high concentrations of CO 2 (>90%, biofuel operations) would yield electrofuels corresponding to approximately 2% of the current demand for transportation fuels (corresponding to 1.5–2 TWh/year). In a 2030 scenario with large-scale biofuels operations based on lignocellulosic feedstocks, the potential for electrofuels production from high-concentration sources increases to 8–11 TWh/year. Finally, renewable electricity and production costs, rather than CO 2 supply, limit the potential for production of electrofuels in Sweden.

  15. Seismic precursors of vulcanian explosions at Ubinas volcano (Peru) : Statistical analysis and source locations

    Science.gov (United States)

    Métaxian, J.-P.; Macedo, O.; Lengline, O.; Monteiller, V.; Taipe, E.

    2009-04-01

    Ubinas stratovolcano (5672 m), located 60 km east from Arequipa city is historically the most active volcano in Peru. The present eruption began on March 25th 2006. A lava plug has been observed at the bottom of the pit crater situated in the south part of the caldeira. The eruptive activity involves very brought closer exhalations rising a few hundred meters above the crater rim to larger plumes produced by explosions that may reach up to 3 kilometers. The seismic activity is characterized by high rates of long-period (LP) event production accompanying eruptive activity and very long period (VLP) events observed at the same time as vulcanian explosions. The LP and VLP events have a spectral content respectively dominated by frequencies between 2-5 Hz and 0.3-0.9 Hz. The vulcanian explosive activity is characterized by the occurrence of LP swarm preceding most of the VLPs by about 2 hours. In some occasions, the LP swarm merges into tremor about half an hour before the explosion. LPs belonging to the same swarm have similar waveform suggesting a unique source area, which could be the conduit and/or the lava plug surface. The monitoring system includes 4 seismic stations, among which one is equipped with a broadband sensor and 2 tiltmeters. In this work we analyzed a catalogue of data including more than 40000 LP events and 130 VLP events recorded between May 2006 and December 2008. The evolution of the average number of LP events preceding explosions was computed. The variation of the LP rate is clearly diverging from the background rate ~ 0.1 days before explosions. In particular, the most energetic explosions are correlated with the biggest increases of seismicity. However this general behavior is not observed for every single explosion. A direct test is now under study in order to check if the earthquake rate can be used as an alert tool for future explosions. To locate the source of LP events belonging to the swarms, we used a method based on the measurement of

  16. Locating the QCD critical end point through peaked baryon number susceptibilities along the freeze-out line

    Science.gov (United States)

    Li, Zhibin; Chen, Yidian; Li, Danning; Huang, Mei

    2018-01-01

    We investigate the baryon number susceptibilities up to fourth order along different freeze-out lines in a holographic QCD model with a critical end point (CEP), and we propose that the peaked baryon number susceptibilities along the freeze-out line can be used as a clean signature to locate the CEP in the QCD phase diagram. On the temperature and baryon chemical potential plane, the cumulant ratio of the baryon number susceptibilities (up to fourth order) forms a ridge along the phase boundary, and develops a sword-shaped “mountain” standing upright around the CEP in a narrow and oblate region. The measurement of baryon number susceptibilities from heavy-ion collision experiments is along the freeze-out line. If the freeze-out line crosses the foot of the CEP mountain, then one can observe the peaked baryon number susceptibilities along the freeze-out line, and the kurtosis of the baryon number distributions has the highest magnitude. The data from the first phase of the beam energy scan program at the Relativistic Heavy Ion Collider indicates that there should be a peak of the kurtosis of the baryon number distribution at a collision energy of around 5 GeV, which suggests that the freeze-out line crosses the foot of the CEP mountain and the summit of the CEP should be located nearby, around a collision energy of 3–7 GeV. Supported by NSFC (11275213, and 11261130311) (CRC 110 by DFG and NSFC), CAS key project KJCX2-EW-N01, and Youth Innovation Promotion Association of CAS

  17. Testing seismic amplitude source location for fast debris-flow detection at Illgraben, Switzerland

    Science.gov (United States)

    Walter, Fabian; Burtin, Arnaud; McArdell, Brian W.; Hovius, Niels; Weder, Bianca; Turowski, Jens M.

    2017-06-01

    Heavy precipitation can mobilize tens to hundreds of thousands of cubic meters of sediment in steep Alpine torrents in a short time. The resulting debris flows (mixtures of water, sediment and boulders) move downstream with velocities of several meters per second and have a high destruction potential. Warning protocols for affected communities rely on raising awareness about the debris-flow threat, precipitation monitoring and rapid detection methods. The latter, in particular, is a challenge because debris-flow-prone torrents have their catchments in steep and inaccessible terrain, where instrumentation is difficult to install and maintain. Here we test amplitude source location (ASL) as a processing scheme for seismic network data for early warning purposes. We use debris-flow and noise seismograms from the Illgraben catchment, Switzerland, a torrent system which produces several debris-flow events per year. Automatic in situ detection is currently based on geophones mounted on concrete check dams and radar stage sensors suspended above the channel. The ASL approach has the advantage that it uses seismometers, which can be installed at more accessible locations where a stable connection to mobile phone networks is available for data communication. Our ASL processing uses time-averaged ground vibration amplitudes to estimate the location of the debris-flow front. Applied to continuous data streams, inversion of the seismic amplitude decay throughout the network is robust and efficient, requires no manual identification of seismic phase arrivals and eliminates the need for a local seismic velocity model. We apply the ASL technique to a small debris-flow event on 19 July 2011, which was captured with a temporary seismic monitoring network. The processing rapidly detects the debris-flow event half an hour before arrival at the outlet of the torrent and several minutes before detection by the in situ alarm system. An analysis of continuous seismic records furthermore

  18. Tackling non-point source water pollution in British Columbia : an action plan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    British Columbia`s approach to water quality management is discussed. The BC efforts include regulating `end of pipe` point discharges from industrial and municipal outfalls. The major remaining cause of water pollution is from non-point sources (NPS). NPS water pollution is caused by the release of pollutants from different and diffuse sources, mostly unregulated and associated with urbanization, agriculture and other forms of land development. The importance of dealing with such problems on an immediate basis to avoid a decline in water quality in the province is emphasized. Major sources of water pollution in British Columbia include: land development, agriculture, storm water runoff, onsite sewage systems, forestry, atmospheric deposition, and marine activities. 3 tabs.

  19. The effect of agricultural non-point Source Pollution of nitrogen and phosphorous on Lake Eutrophication

    Science.gov (United States)

    Xiong, Hanfeng

    2017-05-01

    Based on the data from investigation, the evaluation by equal standard pollution loading method was used to study the agricultural non-point source pollution caused by nitrogen and phosphorous from livestock’s feces pollution, chemical fertilizer pollution and fish breeding pond pollution in Liangzi Lake wetland. The results revealed that: The lost amount of nitrogen and phosphorous was separately 1276.49T, 103.04T; the equivalent standard pollution loading amount was separately 12.76X108 m3, 5.15X108 m3. The lost amount of nitrogen was highest in chemical fertilizer. Based pollution on the understanding of the cause of agricultural non-point source in Liangzi Lake wetland, some countermeasures were suggested according to different pollution source.

  20. Strategies for satellite-based monitoring of CO2 from distributed area and point sources

    Science.gov (United States)

    Schwandner, Florian M.; Miller, Charles E.; Duren, Riley M.; Natraj, Vijay; Eldering, Annmarie; Gunson, Michael R.; Crisp, David

    2014-05-01

    Atmospheric CO2 budgets are controlled by the strengths, as well as the spatial and temporal variabilities of CO2 sources and sinks. Natural CO2 sources and sinks are dominated by the vast areas of the oceans and the terrestrial biosphere. In contrast, anthropogenic and geogenic CO2 sources are dominated by distributed area and point sources, which may constitute as much as 70% of anthropogenic (e.g., Duren & Miller, 2012), and over 80% of geogenic emissions (Burton et al., 2013). Comprehensive assessments of CO2 budgets necessitate robust and highly accurate satellite remote sensing strategies that address the competing and often conflicting requirements for sampling over disparate space and time scales. Spatial variability: The spatial distribution of anthropogenic sources is dominated by patterns of production, storage, transport and use. In contrast, geogenic variability is almost entirely controlled by endogenic geological processes, except where surface gas permeability is modulated by soil moisture. Satellite remote sensing solutions will thus have to vary greatly in spatial coverage and resolution to address distributed area sources and point sources alike. Temporal variability: While biogenic sources are dominated by diurnal and seasonal patterns, anthropogenic sources fluctuate over a greater variety of time scales from diurnal, weekly and seasonal cycles, driven by both economic and climatic factors. Geogenic sources typically vary in time scales of days to months (geogenic sources sensu stricto are not fossil fuels but volcanoes, hydrothermal and metamorphic sources). Current ground-based monitoring networks for anthropogenic and geogenic sources record data on minute- to weekly temporal scales. Satellite remote sensing solutions would have to capture temporal variability through revisit frequency or point-and-stare strategies. Space-based remote sensing offers the potential of global coverage by a single sensor. However, no single combination of orbit

  1. Placing Antismoking Graphic Warning Posters at Retail Point-of-Sale Locations Increases Some Adolescents' Susceptibility to Future Smoking.

    Science.gov (United States)

    Shadel, William G; Martino, Steven C; Setodji, Claude; Dunbar, Michael; Kusuke, Daniela; Lanna, Serafina; Meyer, Amanda

    2017-12-13

    This experiment tested whether introducing graphic antitobacco posters at point-of-sale (POS) had any effect on adolescents' susceptibility to future cigarette smoking and whether these effects were moderated by adolescents' baseline risk of cigarette smoking. The study was conducted in the RAND StoreLab, a life-sized replica of a convenience store that was developed to experimentally evaluate how changing aspects of tobacco advertising displays in retail POS environments influence tobacco use risk and behavior during simulated shopping experiences. In this study, 441 adolescents were randomized to one of the four conditions in a 2 (graphic antismoking poster placed near the tobacco power wall: no, yes) × 2 (graphic antismoking poster placed near the cash register: no, yes) experimental design. The outcome of interest was susceptibility to future cigarette smoking. The addition of antismoking posters at POS led to a significant increase in future smoking susceptibility among those adolescents who already were at high risk for smoking in the future (p < .045). The introduction of graphic antismoking posters had no impact on committed never smokers, regardless of poster location; never smokers' susceptibility to future smoking was uniformly low across experimental conditions. Introducing graphic antismoking posters at POS may have the unintended effect of further increasing cigarette smoking susceptibility among adolescents already at risk. © The Author(s) 2017. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  2. Source ranging with an underwater geographic point in non-cooperative bistatic sonar

    Science.gov (United States)

    Lee, Donghwa; Jung, Tae Jin; Lee, Kyun Kyung; Myung, Hyun

    2014-01-01

    Active sonar is divided into monostatic and bistatic sonar according to the relative positions of the source and the receiver. Bistatic sonar on modern submarines is classified into cooperative and non-cooperative operations. Cooperative operation uses an active signal of a friendly ship; therefore, source information is known a priori, whereas non-cooperative operation utilizes an active signal of the enemy, and hence, it is difficult to acquire source information, such as a source range, which is important for bistatic sonar operation. In order to overcome this difficulty, this paper proposes an estimation method for the source range that employs geographic information, and the utility of the source range estimation is evaluated. For the evaluation, we consider three error components. Then, the validity of the scheme is confirmed through theoretical error analysis and simulation study. The results show that geographic points that satisfy certain specific conditions can be used to estimate the source range within a range of tens of km in the simulation. Finally, we confirm that the receiver could estimate the source range from far away using non-cooperative bistatic sonar.

  3. Location of the Norma transient with the HEAO 1 scanning modulation collimator. [X ray source in Norma Constellation

    Science.gov (United States)

    Fabbiano, G.; Gursky, H.; Schwartz, D. A.; Schwarz, J.; Bradt, H. V.; Doxsey, R. E.

    1978-01-01

    A precise position has been obtained for an X-ray transient source in Norma. The location uncertainty includes a variable star previously suggested to be the optical counterpart. This transient is associated with the steady X-ray source MX 1608-52 and probably with an X-ray burst source. A binary system containing a low-mass primary and a neutron-star or black-hole secondary of a few solar masses is consistent with the observations.

  4. Global Pollution of Surface Waters from Point and Nonpoint Sources of Nitrogen

    Directory of Open Access Journals (Sweden)

    G. van Drecht

    2001-01-01

    Full Text Available Global 0.5- by 0.5-degree resolution estimates are presented on the fate of nitrogen (N stemming from point and nonpoint sources, including plant uptake, denitrification, leaching from the rooting zone, rapid flow through shallow groundwater, and slow flow through deep groundwater to riverine systems. Historical N inputs are used to describe the N flows in groundwater. For nonpoint N sources (agricultural and natural ecosystems, calculations are based on local hydrology, climate, geology, soils, climate and land use combined with data for 1995 on crop production, N inputs from N fertilizers and animal manure, and estimates for ammonia emissions, biological N fixation, and N deposition. For point sources, our estimates are based on population densities and human N emissions, sanitation, and treatment. The results provide a first insight into the magnitude of the N losses from soil-plant systems and point sources in various parts of the world, and the fate of N during transport in atmosphere, groundwater, and surface water. The contribution to the river N load by anthropogenic N pollution is dominant in many river basins in Europe, Asia, and North Africa. Our model results explain much of the variation in measured N export from different world river basins.

  5. A Targeted Search for Point Sources of EeV Photons with the Pierre Auger Observatory

    Energy Technology Data Exchange (ETDEWEB)

    Aab, A. [Institute for Mathematics, Astrophysics and Particle Physics (IMAPP), Radboud Universiteit, Nijmegen (Netherlands); Abreu, P. [Laboratório de Instrumentação e Física Experimental de Partículas—LIP and Instituto Superior Técnico—IST, Universidade de Lisboa—UL, Lisbon (Portugal); Aglietta, M. [INFN, Sezione di Torino, Torino (Italy); Samarai, I. Al [Laboratoire de Physique Nucléaire et de Hautes Energies (LPNHE), Universités Paris 6 et Paris 7, CNRS-IN2P3, Paris (France); Albuquerque, I. F. M. [Universidade de São Paulo, Inst. de Física, São Paulo (Brazil); Allekotte, I. [Centro Atómico Bariloche and Instituto Balseiro (CNEA-UNCuyo-CONICET), San Carlos de Bariloche (Argentina); Almela, A. [Instituto de Tecnologías en Detección y Astropartículas (CNEA, CONICET, UNSAM), Centro Atómico Constituyentes, Comisión Nacional de Energía Atómica, Buenos Aires (Argentina); Castillo, J. Alvarez [Universidad Nacional Autónoma de México, México, D. F., México (Mexico); Alvarez-Muñiz, J. [Universidad de Santiago de Compostela, La Coruña (Spain); Anastasi, G. A. [Gran Sasso Science Institute (INFN), L’Aquila (Italy); and others

    2017-03-10

    Simultaneous measurements of air showers with the fluorescence and surface detectors of the Pierre Auger Observatory allow a sensitive search for EeV photon point sources. Several Galactic and extragalactic candidate objects are grouped in classes to reduce the statistical penalty of many trials from that of a blind search and are analyzed for a significant excess above the background expectation. The presented search does not find any evidence for photon emission at candidate sources, and combined p -values for every class are reported. Particle and energy flux upper limits are given for selected candidate sources. These limits significantly constrain predictions of EeV proton emission models from non-transient Galactic and nearby extragalactic sources, as illustrated for the particular case of the Galactic center region.

  6. Process for automatic location of interest points during mammography stereotaxic examination; Procede de reperage automatique de points d`interet lors d`un examen de stereotaxie en mammographie

    Energy Technology Data Exchange (ETDEWEB)

    Muller, S.

    1995-05-19

    This patent describes a process for automatic location of interest points met during a mammography stereotaxic examination and is made up of an image acquisition numerical system associated with algorithms for images processing. (A.B.). 4 refs., 14 figs.

  7. Using Soluble Reactive Phosphorus and Ammonia to Identify Point Source Discharge from Large Livestock Facilities

    Science.gov (United States)

    Borrello, M. C.; Scribner, M.; Chessin, K.

    2013-12-01

    A growing body of research draws attention to the negative environmental impacts on surface water from large livestock facilities. These impacts are mostly in the form of excessive nutrient loading resulting in significantly decreased oxygen levels. Over-application of animal waste on fields as well as direct discharge into surface water from facilities themselves has been identified as the main contributor to the development of hypoxic zones in Lake Erie, Chesapeake Bay and the Gulf of Mexico. Some regulators claim enforcement of water quality laws is problematic because of the nature and pervasiveness of non-point source impacts. Any direct discharge by a facility is a violation of permits governed by the Clean Water Act, unless the facility has special dispensation for discharge. Previous research by the principal author and others has shown runoff and underdrain transport are the main mechanisms by which nutrients enter surface water. This study utilized previous work to determine if the effects of non-point source discharge can be distinguished from direct (point-source) discharge using simple nutrient analysis and dissolved oxygen (DO) parameters. Nutrient and DO parameters were measured from three sites: 1. A stream adjacent to a field receiving manure, upstream of a large livestock facility with a history of direct discharge, 2. The same stream downstream of the facility and 3. A stream in an area relatively unimpacted by large-scale agriculture (control site). Results show that calculating a simple Pearson correlation coefficient (r) of soluble reactive phosphorus (SRP) and ammonia over time as well as temperature and DO, distinguishes non-point source from point source discharge into surface water. The r value for SRP and ammonia for the upstream site was 0.01 while the r value for the downstream site was 0.92. The control site had an r value of 0.20. Likewise, r values were calculated on temperature and DO for each site. High negative correlations

  8. OCO-2 Detection of Atmospheric Carbon Dioxide Variability over Natural and Anthropogenic Point-Sources

    Science.gov (United States)

    Schwandner, F. M.; Gunson, M. R.; Miller, C. E.; Carn, S. A.; Eldering, A.; Krings, T.; Verhulst, K. R.; Schimel, D.; Nguyen, H.; Crisp, D.; O'Dell, C.; Osterman, G. B.; Iraci, L. T.; Podolske, J. R.

    2017-12-01

    Natural and anthropogenic emissions of carbon dioxide (CO2) to the atmosphere vary temporally and spatially at the 0.1-10 kilometer-scale. Plumes from regional and point-scale emission sources may be discernable from space within their spatial context but the characteristics of aging plumes may pose additional challenges to quantification and attribution. Space-borne measurements by NASA's Orbiting Carbon Observatory-2 (OCO-2) expose distinct structures of atmospheric carbon dioxide on kilometer scales over known anthropogenic and natural point sources. Urban areas, including megacities, account for over 70% of anthropogenic CO2 emissions. In cities, CO2 emitted from dense clusters of mobile and stationary point sources may form persistent CO2 enhancements producing urban CO2 domes. OCO-2 measurements cross the Los Angeles basin several times a year consistently show enhancements in the column average CO2 dry air mole fraction, XCO2, with highest values over the urban core and decreasing through suburban areas to rural background values, with a seasonally variability of 4.4 to 6.1 ppm. For natural point sources, volcanoes may emit CO2 continuously but variably, at source strengths similar to fossil-fuel burning power plants. An OCO-2 transect passing directly downwind of the persistent isolated natural CO2 plume emanating from Yasur volcano (Vanuatu) produces a narrow strand of enhanced XCO2 values (ΔXCO2 3.4 ppm). Gaussian plume modeling of this plume is consistent with a 41.6 kt d-1 CO2 point source. Additional plume detections over Aoba and Ambrym volcanoes (Vanuatu) show similar results. This first quantitative space-borne volcanic CO2 plume flux estimate puts volcanic CO2 emissions into context: the largest continuous volcanic CO2 emitters on Earth are similar in source strength to a large coal fired power plant, but barely reach the lower end of the range of the 70 largest fossil-fuel burning power plants on Earth, which themselves are dwarfed by megacity

  9. Column Number Density Expressions Through M = 0 and M = 1 Point Source Plumes Along Any Straight Path

    Science.gov (United States)

    Woronowicz, Michael

    2017-01-01

    Providers of payloads carried aboard the International Space Station must conduct analyses to demonstrate that any planned gaseous venting events generate no more than a certain level of material that may interfere with optical measurements from other experiments or payloads located nearby. This requirement is expressed in terms of a maximum column number density (CND). Depending on the level of rarefaction, such venting may be characterized by effusion for low flow rates, or by a sonic distribution at higher levels. Since the relative locations of other sensitive payloads are often unknown because they may refer to future projects, this requirement becomes a search for the maximum CND along any path.In another application, certain astronomical observations make use of CND to estimate light attenuation from a distant star through gaseous plumes, such as the Fermi Bubbles emanating from the vicinity of the black hole at the center of our Milky Way galaxy, in order to infer the amount of material being expelled via those plumes.This paper presents analytical CND expressions developed for general straight paths based upon a free molecule point source model for steady effusive flow and for a distribution fitted to model flows from a sonic orifice. Among other things, in this Mach number range it is demonstrated that the maximum CND from a distant location occurs along the path parallel to the source plane that intersects the plume axis. For effusive flows this value is exactly twice the CND found along the ray originating from that point of intersection and extending to infinity along the plumes axis. For sonic plumes this ratio is reduced to about 43.

  10. Search for Cosmic Neutrino Point Sources with Four Years of Data from the ANTARES Telescope

    Science.gov (United States)

    Adrián-Martínez, S.; Samarai, I. Al; Albert, A.; André, M.; Anghinolfi, M.; Anton, G.; Anvar, S.; Ardid, M.; Astraatmadja, T.; Aubert, J.-J.; Baret, B.; Basa, S.; Bertin, V.; Biagi, S.; Bigongiari, C.; Bogazzi, C.; Bou-Cabo, M.; Bouhou, B.; Bouwhuis, M. C.; Brunner, J.; Busto, J.; Capone, A.; Cârloganu, C.; Carr, J.; Cecchini, S.; Charif, Z.; Charvis, Ph.; Chiarusi, T.; Circella, M.; Coniglione, R.; Core, L.; Costantini, H.; Coyle, P.; Creusot, A.; Curtil, C.; De Bonis, G.; Decowski, M. P.; Dekeyser, I.; Deschamps, A.; Distefano, C.; Donzaud, C.; Dornic, D.; Dorosti, Q.; Drouhin, D.; Eberl, T.; Emanuele, U.; Enzenhöfer, A.; Ernenwein, J.-P.; Escoffier, S.; Fehn, K.; Fermani, P.; Ferri, M.; Ferry, S.; Flaminio, V.; Folger, F.; Fritsch, U.; Fuda, J.-L.; Galatà, S.; Gay, P.; Geyer, K.; Giacomelli, G.; Giordano, V.; Gleixner, A.; Gómez-González, J. P.; Graf, K.; Guillard, G.; Hallewell, G.; Hamal, M.; van Haren, H.; Heijboer, A. J.; Hello, Y.; Hernández-Rey, J. J.; Herold, B.; Hößl, J.; Hsu, C. C.; de Jong, M.; Kadler, M.; Kalekin, O.; Kappes, A.; Katz, U.; Kavatsyuk, O.; Kooijman, P.; Kopper, C.; Kouchner, A.; Kreykenbohm, I.; Kulikovskiy, V.; Lahmann, R.; Lambard, G.; Larosa, G.; Lattuada, D.; Leonora, E.; Lefèvre, D.; Lim, G.; Lo Presti, D.; Loehner, H.; Loucatos, S.; Louis, F.; Mangano, S.; Marcelin, M.; Margiotta, A.; Martínez-Mora, J. A.; Meli, A.; Montaruli, T.; Morganti, M.; Motz, H.; Neff, M.; Nezri, E.; Palioselitis, D.; Păvălaş, G. E.; Payet, K.; Petrovic, J.; Piattelli, P.; Popa, V.; Pradier, T.; Presani, E.; Racca, C.; Reed, C.; Riccobene, G.; Richter, R.; Rivière, C.; Robert, A.; Roensch, K.; Rostovtsev, A.; Ruiz-Rivas, J.; Rujoiu, M.; Samtleben, D. F. E.; Sapienza, P.; Schmid, J.; Schnabel, J.; Schuller, J.-P.; Schüssler, F.; Seitz, T.; Shanidze, R.; Simeone, F.; Spies, A.; Spurio, M.; Steijger, J. J. M.; Stolarczyk, Th.; Sánchez-Losa, A.; Taiuti, M.; Tamburini, C.; Trovato, A.; Vallage, B.; Vallée, C.; Van Elewyck, V.; Vecchi, M.; Vernin, P.; Visser, E.; Wagner, S.; Wijnker, G.; Wilms, J.; de Wolf, E.; Yepes, H.; Zaborov, D.; Zornoza, J. D.; Zúñiga, J.

    2012-11-01

    In this paper, a time-integrated search for point sources of cosmic neutrinos is presented using the data collected from 2007 to 2010 by the ANTARES neutrino telescope. No statistically significant signal has been found and upper limits on the neutrino flux have been obtained. Assuming an E -2 ν spectrum, these flux limits are at 1-10 ×10-8 GeV cm-2 s-1 for declinations ranging from -90° to 40°. Limits for specific models of RX J1713.7-3946 and Vela X, which include information on the source morphology and spectrum, are also given.

  11. An Ultradeep Chandra Catalog of X-Ray Point Sources in the Galactic Center Star Cluster

    Science.gov (United States)

    Zhu, Zhenlin; Li, Zhiyuan; Morris, Mark R.

    2018-04-01

    We present an updated catalog of X-ray point sources in the inner 500″ (∼20 pc) of the Galactic center (GC), where the nuclear star cluster (NSC) stands, based on a total of ∼4.5 Ms of Chandra observations taken from 1999 September to 2013 April. This ultradeep data set offers unprecedented sensitivity for detecting X-ray sources in the GC, down to an intrinsic 2–10 keV luminosity of 1.0 × 1031 erg s‑1. A total of 3619 sources are detected in the 2–8 keV band, among which ∼3500 are probable GC sources and ∼1300 are new identifications. The GC sources collectively account for ∼20% of the total 2–8 keV flux from the inner 250″ region where detection sensitivity is the greatest. Taking advantage of this unprecedented sample of faint X-ray sources that primarily traces the old stellar populations in the NSC, we revisit global source properties, including long-term variability, cumulative spectra, luminosity function, and spatial distribution. Based on the equivalent width and relative strength of the iron lines, we suggest that in addition to the arguably predominant population of magnetic cataclysmic variables (CVs), nonmagnetic CVs contribute substantially to the detected sources, especially in the lower-luminosity group. On the other hand, the X-ray sources have a radial distribution closely following the stellar mass distribution in the NSC, but much flatter than that of the known X-ray transients, which are presumably low-mass X-ray binaries (LMXBs) caught in outburst. This, together with the very modest long-term variability of the detected sources, strongly suggests that quiescent LMXBs are a minor (less than a few percent) population.

  12. Source Population and Acceleration Location of Suprathermal Heavy Ions in Corotating Interaction Regions

    Energy Technology Data Exchange (ETDEWEB)

    Filwett, R. J.; Desai, M. I. [University of Texas at San Antonio, San Antonio, TX (United States); Dayeh, M. A.; Broiles, T. W. [Southwest Research Institute, San Antonio, TX (United States)

    2017-03-20

    We have analyzed the ∼20–320 keV nucleon{sup −1} suprathermal (ST) heavy ion abundances in 41 corotating interaction regions (CIRs) observed by the Wind spacecraft from 1995 January to 2008 December. Our results are: (1) the CIR Fe/CNO and NeS/CNO ratios vary with the sunspot number, with values being closer to average solar energetic particle event values during solar maxima and lower than nominal solar wind values during solar minima. The physical mechanism responsible for the depleted abundances during solar minimum remains an open question. (2) The Fe/CNO increases with energy in the 6 events that occurred during solar maximum, while no such trends are observed for the 35 events during solar minimum. (3) The Fe/CNO shows no correlation with the average solar wind speed. (4) The Fe/CNO is well correlated with the corresponding upstream ∼20–320 keV nucleon{sup −1} Fe/CNO and not with the solar wind Fe/O measured by ACE in 31 events. Using the correlations between the upstream ∼20–40 keV nucleon{sup −1} Fe/CNO and the ∼20–320 keV nucleon{sup −1} Fe/CNO in CIRs, we estimate that, on average, the ST particles traveled ∼2 au along the nominal Parker spiral field line, which corresponds to upper limits for the radial distance of the source or acceleration location of ∼1 au beyond Earth orbit. Our results are consistent with those obtained from recent surveys, and confirm that CIR ST heavy ions are accelerated more locally, and are at odds with the traditional viewpoint that CIR ions seen at 1 au are bulk solar wind ions accelerated between 3 and 5 au.

  13. A point-source norovirus outbreak caused by exposure to fomites.

    Science.gov (United States)

    Repp, Kimberly K; Keene, William E

    2012-06-01

    We investigated a norovirus outbreak (genotype GII.2) affecting 9 members of a soccer team. Illness was associated with touching a reusable grocery bag or consuming its packaged food contents (risk difference, 0.636; P fomites can lead to subsequent point-source outbreaks. When feasible, we recommend dedicated bathrooms for sick persons and informing cleaning staff (professional or otherwise) about the need for adequate environmental sanitation of surfaces and fomites to prevent spread.

  14. Gamma Rays from the Inner Milky Way: Dark Matter or Point Sources?

    CERN Multimedia

    CERN. Geneva

    2015-01-01

    Studies of data from the Fermi Gamma-Ray Space Telescope have revealed bright gamma-ray emission from the central regions of our galaxy, with a spatial and spectral profile consistent with annihilating dark matter. I will present a new model-independent analysis that suggests that rather than originating from dark matter, the GeV excess may arise from a surprising new population of as-yet-unresolved gamma-ray point sources in the heart of the Milky Way.

  15. Magnetic point sources in three dimensional Brans-Dicke gravity theories

    OpenAIRE

    Dias, Oscar J. C.; Lemos, Jose' P. S.

    2002-01-01

    We obtain geodesically complete spacetimes generated by static and rotating magnetic point sources in an Einstein-Maxwell-Dilaton theory of the Brans-Dicke type in three dimensions (3D). The theory is specified by three fields, the dilaton, the graviton and the electromagnetic field, and two parameters, the cosmological constant and the Brans-Dicke parameter, w. When the Brans-Dicke parameter is infinity, our solution reduces to the magnetic counterpart of the BTZ solution, while the w=0 case...

  16. Prevention and Control of Agricultural Non-Point Source Pollutions in UK and Suggestions to China

    OpenAIRE

    Liu, Kun; Ren, Tianzhi; Wu, Wenliang; Meng, Fanquiao; Bellarby, Jessica; Smith, Laurence

    2016-01-01

    Currently, the world is facing challenges of maintaining food production growth while improving agricultural ecological environmental quality. The prevention and control of agricultural non-point source pollution, a key component of these challenges, is a systematic program which integrates many factors such as technology and its extension, relevant regulation and policies. In the project of UK-China Sustainable Agriculture Innovation Network, we undertook a comprehensive analysis of the prev...

  17. Simulations of HXR Foot-point Source Sizes for Modified Thick-target Models

    Czech Academy of Sciences Publication Activity Database

    Moravec, Z.; Varady, Michal; Karlický, Marian; Kašparová, Jana

    2013-01-01

    Roč. 37, č. 2 (2013), s. 535-540 ISSN 1845-8319. [Hvar Astrophysical Colloquium /12./. Hvar, 03.09.2012-07.09.2012] R&D Projects: GA ČR GAP209/10/1680; GA ČR GAP209/12/0103 Institutional support: RVO:67985815 Keywords : solar flares * hard X-rays * foot-point sources Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics

  18. ESTIMASI BEBAN PENCEMARAN POINT SOURCE DAN LIMBAH DOMESTIK DI SUNGAI KALIBARU TIMUR PROVINSI DKI JAKARTA, INDONESIA

    Directory of Open Access Journals (Sweden)

    Rahmat Pangestu

    2017-12-01

    Full Text Available East Kalibaru River is one of the thirteen rivers flowing through Jakarta. East Kalibaru River has an important role in development of the region. Considering the increasing activities of people, settlements and number of industries along the East Kalibaru River, it is necessary to calculate contaminants load that discharged into the water body East Kalibaru. This study conducted to determine the point source and domestic waste pollution loads, using parameters of BOD, COD and TSS. The analysis showed that the total pollution loads such are calculated as 43.714 kg/day for BOD, 60.107 kg/day for COD and total 41.529 kg/day for TSS. Total pollution load discharged into river from point source effluent is amounted of 249 kg/day for BOD, 1.505 kg/day for COD and total 411 kg/day for TSS. Effect of domestic waste is very insignificant compared to the effect of point source that went into the river. The result suggest that approach that need to be done to reduce the burden of domestic waste water pollutants is by performing additional production or communal Wastewater Treatment Plant (WWTP in densely populated areas.

  19. Temporal-spatial distribution of non-point source pollution in a drinking water source reservoir watershed based on SWAT

    Directory of Open Access Journals (Sweden)

    M. Wang

    2015-05-01

    Full Text Available The conservation of drinking water source reservoirs has a close relationship between regional economic development and people’s livelihood. Research on the non-point pollution characteristics in its watershed is crucial for reservoir security. Tang Pu Reservoir watershed was selected as the study area. The non-point pollution model of Tang Pu Reservoir was established based on the SWAT (Soil and Water Assessment Tool model. The model was adjusted to analyse the temporal-spatial distribution patterns of total nitrogen (TN and total phosphorus (TP. The results showed that the loss of TN and TP in the reservoir watershed were related to precipitation in flood season. And the annual changes showed an "M" shape. It was found that the contribution of loss of TN and TP accounted for 84.5% and 85.3% in high flow years, and for 70.3% and 69.7% in low flow years, respectively. The contributions in normal flow years were 62.9% and 63.3%, respectively. The TN and TP mainly arise from Wangtan town, Gulai town, and Wangyuan town, etc. In addition, it was found that the source of TN and TP showed consistency in space.

  20. Aberration correction by nonlinear beam mixing: generation of a pseudo point sound source.

    Science.gov (United States)

    Seo, Jongbum; Choi, J J; Fowlkes, J Brian; O'Donnell, Matthew; Cain, Charles A

    2005-11-01

    Nonlinear beam mixing with microbubbles was explored to create a pseudo point source for aberration correction of therapeutic ultrasound. A damping coefficient for a bubble driven by a dual frequency sound field was derived by revisiting Prosperetti's linearized damping model. As a result, the overall damping term for dual frequency was obtained by linear summation of two damping terms for each frequency. The numerical simulation based on the bubble model suggests that the most efficient size range to generate a 1 MHz frequency from 4 MHz and 5 MHz sound sources is 2.6 to 3.0 microm. Furthermore, this size range constitutes the primary distribution of a specific ultrasound contrast agent. When a chamber of 0.1% of the diluted agent is sonified by 4 MHz and 5 MHz sound beams with 80 degrees incident angle between them, an approximately 100 Pa, 1 MHz difference frequency signal can be measured approximately 10 cm away. In addition, the received 1 MHz difference frequency signal shows omni-directional characteristics, even though the overlap zone of the two sound beams is on the order of the difference frequency wavelength. Therefore, the induced sound source can be considered as a pseudo point source and is expected to be useful for aberration correction for therapeutic ultrasound.

  1. [Impacts of the urbanization on waters non-point source pollution].

    Science.gov (United States)

    Yang, Liu; Ma, Ke-Ming; Guo, Qing-hai; Zhao, Jing-zhu

    2004-11-01

    Non-point source (NPS) pollution is the prominent source of water pollution in many countries, included America and China, of the world. Urban NPS pollution was attached little importance for long, compared with agriculture NPS pollution. While urbanization is the dominant form of land-use change in terms of impacts on water quality, the hydrology, other physical properties of watersheds as well as their NPS pollution potential at present. The formation of urban NPS pollution of water could be described by "source-process-sink". Urbanization has changed the source, process and sink of urban NPS pollution. A review was conducted on the international researches of urbanization impacts on NPS pollution in urban water environment from the point of view of "describe-predict and evaluation-application". The studies of urbanization impacts on urban NPS pollution were focused on modeling the process of urban NPS pollution by hydrologic model, predicting the pollutants load of NPS pollution. It is a fresh methodology that the relationship between urbanization and urban NPS pollution of water was analyzed by the method of landscape change and ecological process. The research on temporal-spatial comprehensive impacts of landscape pattern changes, led by urbanization, on the urban NPS pollution will be one of the hotspots.

  2. An Improved Statistical Point-source Foreground Model for the Epoch of Reionization

    Energy Technology Data Exchange (ETDEWEB)

    Murray, S. G.; Trott, C. M.; Jordan, C. H. [ARC Centre of Excellence for All-sky Astrophysics (CAASTRO) (Australia)

    2017-08-10

    We present a sophisticated statistical point-source foreground model for low-frequency radio Epoch of Reionization (EoR) experiments using the 21 cm neutral hydrogen emission line. Motivated by our understanding of the low-frequency radio sky, we enhance the realism of two model components compared with existing models: the source count distributions as a function of flux density and spatial position (source clustering), extending current formalisms for the foreground covariance of 2D power-spectral modes in 21 cm EoR experiments. The former we generalize to an arbitrarily broken power law, and the latter to an arbitrary isotropically correlated field. This paper presents expressions for the modified covariance under these extensions, and shows that for a more realistic source spatial distribution, extra covariance arises in the EoR window that was previously unaccounted for. Failure to include this contribution can yield bias in the final power-spectrum and under-estimate uncertainties, potentially leading to a false detection of signal. The extent of this effect is uncertain, owing to ignorance of physical model parameters, but we show that it is dependent on the relative abundance of faint sources, to the effect that our extension will become more important for future deep surveys. Finally, we show that under some parameter choices, ignoring source clustering can lead to false detections on large scales, due to both the induced bias and an artificial reduction in the estimated measurement uncertainty.

  3. Large Industrial Point Sources in Italy: a focus on mercury concentrations resulting from three seasonal ship-borne measurements

    Directory of Open Access Journals (Sweden)

    Bencardino M.

    2013-04-01

    Full Text Available In Italy there are 25 Large Industrial Point Sources whose mercury emissions in air exceed the established threshold of 10 kg year−1. Many of these mercury point sources, mostly distributed along the Italian coastal area, are located at sites qualified as National Interest Rehabilitation Sites because of documented contamination in qualitative and/or quantitative terms and of potential health impact. Atmospheric mercury emissions related to Italian Large Industrial Point Sources, with a value of 1.04 Mg·yr−1 for 2007, have a not negligible contribution, accounting, on their own, for more than 10% of the total mercury emissions resulting from all activity sectors at a national level. Among others, thermal power stations, pig iron and steel as well as basic inorganic chemical production, result to be the main contributing industrial activities. In order to assess how mercury species concentrations and distribution in the Marine Boundary Layer (MBL change with vicinity to large industrial sites, measurements of atmospheric mercury were performed during three oceanographic campaigns aboard the Research Vessel (R.V. Urania of the Italian CNR. Collection of GEM, GOM and PBM was conducted across the Adriatic sea, during autumn 2004 (27th of October to 12th of November and summer 2005 (17th to 29th of June, and across the Tyrrhenian sea during autumn 2007 (12th of September to 1st October. Analysis were carried out with reference to the period in which the R.V. Urania has stopped close to the main Italian industrial contaminated sites. Explorative statistical parameters of atmospheric mercury species were computed over each single stop-period and then compared with the overall cruise campaign measurements. Results are herein presented and discussed.

  4. Analytical volcano deformation modelling: A new and fast generalized point-source approach with application to the 2015 Calbuco eruption

    Science.gov (United States)

    Nikkhoo, M.; Walter, T. R.; Lundgren, P.; Prats-Iraola, P.

    2015-12-01

    Ground deformation at active volcanoes is one of the key precursors of volcanic unrest, monitored by InSAR and GPS techniques at high spatial and temporal resolution, respectively. Modelling of the observed displacements establishes the link between them and the underlying subsurface processes and volume change. The so-called Mogi model and the rectangular dislocation are two commonly applied analytical solutions that allow for quick interpretations based on the location, depth and volume change of pressurized spherical cavities and planar intrusions, respectively. Geological observations worldwide, however, suggest elongated, tabular or other non-equidimensional geometries for the magma chambers. How can these be modelled? Generalized models such as the Davis's point ellipsoidal cavity or the rectangular dislocation solutions, are geometrically limited and could barely improve the interpretation of data. We develop a new analytical artefact-free solution for a rectangular dislocation, which also possesses full rotational degrees of freedom. We construct a kinematic model in terms of three pairwise-perpendicular rectangular dislocations with a prescribed opening only. This model represents a generalized point source in the far field, and also performs as a finite dislocation model for planar intrusions in the near field. We show that through calculating the Eshelby's shape tensor the far-field displacements and stresses of any arbitrary triaxial ellipsoidal cavity can be reproduced by using this model. Regardless of its aspect ratios, the volume change of this model is simply the sum of the volume change of the individual dislocations. Our model can be integrated in any inversion scheme as simply as the Mogi model, profiting at the same time from the advantages of a generalized point source. After evaluating our model by using a boundary element method code, we apply it to ground displacements of the 2015 Calbuco eruption, Chile, observed by the Sentinel-1

  5. Identifying elements of the plumbing system beneath Kilauea Volcano, Hawaii, from the source locations of very-long-period signals

    Science.gov (United States)

    Almendros, J.; Chouet, B.; Dawson, P.; Bond, T.

    2002-01-01

    We analyzed 16 seismic events recorded by the Hawaiian broad-band seismic network at Kilauca Volcano during the period September 9-26, 1999. Two distinct types of event are identified based on their spectral content, very-long-period (VLP) waveform, amplitude decay pattern and particle motion. We locate the VLP signals with a method based on analyses of semblance and particle motion. Different source regions are identified for the two event types. One source region is located at depths of ~1 km beneath the northeast edge of the Halemaumau pit crater. A second region is located at depths of ~8 km below the northwest quadrant of Kilauea caldera. Our study represents the first time that such deep sources have been identified in VLP data at Kilauea. This discovery opens the possibility of obtaining a detailed image of the location and geometry of the magma plumbing system beneath this volcano based on source locations and moment tensor inversions of VLP signals recorded by a permanent, large-aperture broad-band network.

  6. Diffusion of dust particles from a point-source above ground level

    International Nuclear Information System (INIS)

    Hassan, M.H.A.; Eltayeb, I.A.

    1998-10-01

    A pollutant of small particles is emitted by a point source at a height h above ground level in an atmosphere in which a uni-directional wind speed, U, is prevailing. The pollutant is subjected to diffusion in all directions in the presence of advection and settling due to gravity. The equation governing the concentration of the pollutant is studied with the wind speed and the different components of diffusion tensor are proportional to the distance above ground level and the source has a uniform strength. Adopting a Cartesian system of coordinates in which the x-axis lies along the direction of the wind velocity, the z-axis is vertically upwards and the y-axis completes the right-hand triad, the solution for the concentration c(x,y,z) is obtained in closed form. The relative importance of the components of diffusion along the three axes is discussed. It is found that for any plane y=constant (=A), c(x,y,z) is concentrated along a curve of ''extensive pollution''. In the plane A=0, the concentration decreases along the line of extensive pollution as we move away from the source. However, for planes A≅0, the line of extensive pollution possesses a point of accumulation, which lies at a nonzero value of x. As we move away from the plane A=0, the point of accumulation moves laterally away from the plane x=0 and towards the plane z=0. The presence of the point of accumulation is entirely due to the presence of lateral diffusion. (author)

  7. Identify source location and release time for pollutants undergoing super-diffusion and decay: Parameter analysis and model evaluation

    Science.gov (United States)

    Zhang, Yong; Sun, HongGuang; Lu, Bingqing; Garrard, Rhiannon; Neupauer, Roseanna M.

    2017-09-01

    Backward models have been applied for four decades by hydrologists to identify the source of pollutants undergoing Fickian diffusion, while analytical tools are not available for source identification of super-diffusive pollutants undergoing decay. This technical note evaluates analytical solutions for the source location and release time of a decaying contaminant undergoing super-diffusion using backward probability density functions (PDFs), where the forward model is the space fractional advection-dispersion equation with decay. Revisit of the well-known MADE-2 tracer test using parameter analysis shows that the peak backward location PDF can predict the tritium source location, while the peak backward travel time PDF underestimates the tracer release time due to the early arrival of tracer particles at the detection well in the maximally skewed, super-diffusive transport. In addition, the first-order decay adds additional skewness toward earlier arrival times in backward travel time PDFs, resulting in a younger release time, although this impact is minimized at the MADE-2 site due to tritium's half-life being relatively longer than the monitoring period. The main conclusion is that, while non-trivial backward techniques are required to identify pollutant source location, the pollutant release time can and should be directly estimated given the speed of the peak resident concentration for super-diffusive pollutants with or without decay.

  8. Reprint of Inexact Bregman iteration for deconvolution of superimposed extended and point sources

    Science.gov (United States)

    Benfenati, A.; Ruggiero, V.

    2015-04-01

    In this paper we consider the deconvolution of high contrast images consisting of very bright stars (point component) and smooth structures underlying the stars (diffuse component). A typical case is a weak diffuse jet line emission superimposed to a strong stellar continuum. In order to reconstruct the diffuse component, the original object can be regarded as the sum of these two components. When the position of the point sources is known, a regularization term can be introduced for the second component. An approximation of the original object can be obtained by solving a reduced variational problem whose unknowns are the intensities of the stars and the diffuse component. We analyze this problem when the detected image is corrupted by Poisson noise and Tikhonov-like regularization is used, giving conditions for the existence and the uniqueness of the solution. Furthermore, since only an overestimation of the regularization parameter is available, we propose to solve the variational problem by inexact Bregman iteration combined with a Scaled Gradient Projection method (SGP). Numerical simulations show that the images obtained with this approach enable us to reconstruct the original intensity distribution around the point source with satisfactory accuracy.

  9. Inexact Bregman iteration for deconvolution of superimposed extended and point sources

    Science.gov (United States)

    Benfenati, A.; Ruggiero, V.

    2015-03-01

    In this paper we consider the deconvolution of high contrast images consisting of very bright stars (point component) and smooth structures underlying the stars (diffuse component). A typical case is a weak diffuse jet line emission superimposed to a strong stellar continuum. In order to reconstruct the diffuse component, the original object can be regarded as the sum of these two components. When the position of the point sources is known, a regularization term can be introduced for the second component. An approximation of the original object can be obtained by solving a reduced variational problem whose unknowns are the intensities of the stars and the diffuse component. We analyze this problem when the detected image is corrupted by Poisson noise and Tikhonov-like regularization is used, giving conditions for the existence and the uniqueness of the solution. Furthermore, since only an overestimation of the regularization parameter is available, we propose to solve the variational problem by inexact Bregman iteration combined with a Scaled Gradient Projection method (SGP). Numerical simulations show that the images obtained with this approach enable us to reconstruct the original intensity distribution around the point source with satisfactory accuracy.

  10. Joint sensor location/power rating optimization for temporally-correlated source estimation

    KAUST Repository

    Bushnaq, Osama M.

    2017-12-22

    The optimal sensor selection for scalar state parameter estimation in wireless sensor networks is studied in the paper. A subset of N candidate sensing locations is selected to measure a state parameter and send the observation to a fusion center via wireless AWGN channel. In addition to selecting the optimal sensing location, the sensor type to be placed in these locations is selected from a pool of T sensor types such that different sensor types have different power ratings and costs. The sensor transmission power is limited based on the amount of energy harvested at the sensing location and the type of the sensor. The Kalman filter is used to efficiently obtain the MMSE estimator at the fusion center. Sensors are selected such that the MMSE estimator error is minimized subject to a prescribed system budget. This goal is achieved using convex relaxation and greedy algorithm approaches.

  11. Mercury exposure in terrestrial birds far downstream of an historical point source

    International Nuclear Information System (INIS)

    Jackson, Allyson K.; Evers, David C.; Folsom, Sarah B.; Condon, Anne M.; Diener, John; Goodrick, Lizzie F.; McGann, Andrew J.; Schmerfeld, John; Cristol, Daniel A.

    2011-01-01

    Mercury (Hg) is a persistent environmental contaminant found in many freshwater and marine ecosystems. Historical Hg contamination in rivers can impact the surrounding terrestrial ecosystem, but there is little known about how far downstream this contamination persists. In 2009, we sampled terrestrial forest songbirds at five floodplain sites up to 137 km downstream of an historical source of Hg along the South and South Fork Shenandoah Rivers (Virginia, USA). We found that blood total Hg concentrations remained elevated over the entire sampling area and there was little evidence of decline with distance. While it is well known that Hg is a pervasive and long-lasting aquatic contaminant, it has only been recently recognized that it also biomagnifies effectively in floodplain forest food webs. This study extends the area of concern for terrestrial habitats near contaminated rivers for more than 100 km downstream from a waterborne Hg point source. - Highlights: → We report blood mercury levels for terrestrial songbirds downstream of contamination. → Blood mercury levels remain elevated above reference for at least 137 km downstream. → Trends vary based on foraging guild and migration strategy. → Mercury affects terrestrial biota farther downstream than previously documented. - Blood mercury levels of forest songbirds remain elevated above reference levels for at least 137 km downstream of historical point source.

  12. The Vacuum Spark VSX-200 as a Soft X-Ray Point Source for Laboratory Microlithography

    Science.gov (United States)

    Panarella, Emilio

    2001-10-01

    The technology of X-ray point plasma sources is taking over the role that previously was retained by the multiple beam synchrotrons as radiation source for submicron lithography. A Plasma Point Source System (VSX 200) has been designed by our company ALFT as an entrance tool for Universities and other Research Laboratories working in the field of semiconductors. Because the radiation is emitted in small dose in each spark, it is necessary to repeat the phenomenon at high frequency in order to have a quasi-continuous wave. The soft X-ray power distribution is uniform, thus meeting the requirement for microlithography. The output of the VSX 200 is 200 mW of 0.93 keV radiation ( ~14 angstroms) in the copper line emitted continuously and reliably. Our plan is to increase the power level to 2 W for a low volume market that requires performance of 1 Wafer Layer per Hour (WLPH) or less, and then scale the device to eventually reach the silicon market that requires 20 WLPH. We expect to be able to support R&D and low volume applications such as Military Communication GaAs Chips by year-end. A demonstration system will be available in California at that time.

  13. Shifting primary energy source and NOx emission location with plug-in hybrid vehicles

    Science.gov (United States)

    Karman, Deniz

    2011-06-01

    Plug-in hybrid vehicles (PHEVs) present an interesting technological opportunity for using non-fossil primary energy in light duty passenger vehicles, with the associated potential for reducing air pollutant and greenhouse gas emissions, to the extent that the electric power grid is fed by non-fossil sources. This perspective, accompanying the article by Thompson et al (2011) in this issue, will touch on two other studies that are directly related: the Argonne study (Elgowainy et al 2010) and a PhD thesis from Utrecht (van Vliet 2010). Thompson et al (2011) have examined air quality effects in a case where the grid is predominantly fossil fed. They estimate a reduction of 7.42 tons/day of NOx from motor vehicles as a result of substituting electric VMTs for 20% of the light duty gasoline vehicle miles traveled. To estimate the impact of this reduction on air quality they also consider the increases in NOx emissions due to the increased load on electricity generating units. The NOx emission increases are estimated as 4.0, 5.5 and 6.3 tons for the Convenience, Battery and Night charging scenarios respectively. The net reductions are thus in the 1.1-3.4 tons/day range. The air quality modelling results presented show that the air quality impact from a ground-level ozone perspective is favorable overall, and while the effect is stronger in some localities, the difference between the three scenarios is small. This is quite significant and suggests that localization of the NOx emissions to point sources has a more pronounced effect than the absolute reductions achieved. Furthermore it demonstrates that localization of NOx emissions to electricity generating units by using PHEVs in vehicle traffic has beneficial effects for air quality not only by minimizing direct human exposure to motor vehicle emissions, but also due to reduced exposure to secondary pollutants (i.e. ozone). In an electric power grid with a smaller share of fossil fired generating units, the beneficial

  14. Avoiding radiation exposure while training to locate a radioactive source: a virtual reality exercise

    International Nuclear Information System (INIS)

    Marins, E.R.; Cotelli do Espírito Santo, A.; Abreu Mól, A. C. de; Cunha, G.; Landau, L.

    2015-01-01

    A technician undergoing radioprotection training must learn to use radiation detectors. Practical exercises involve being near to radiation sources. The work here presented reduces the exposure to individuals using a virtual environment to achieve preliminary apprenticeship prior using real radioactive sources. (authors)

  15. Quantifying point source emissions with atmospheric inversions and aircraft measurements: the Aliso Canyon natural gas leak as a tracer experiment

    Science.gov (United States)

    Gourdji, S.; Yadav, V.; Karion, A.; Mueller, K. L.; Kort, E. A.; Conley, S.; Ryerson, T. B.; Nehrkorn, T.

    2017-12-01

    The ability of atmospheric inverse models to detect, spatially locate and quantify emissions from large point sources in urban domains needs improvement before inversions can be used reliably as carbon monitoring tools. In this study, we use the Aliso Canyon natural gas leak from October 2015 to February 2016 (near Los Angeles, CA) as a natural tracer experiment to assess inversion quality by comparison with published estimates of leak rates calculated using a mass balance approach (Conley et al., 2016). Fourteen dedicated flights were flown in horizontal transects downwind and throughout the duration of the leak to sample CH4 mole fractions and collect meteorological information for use in the mass-balance estimates. The same CH4 observational data were then used here in geostatistical inverse models with no prior assumptions about the leak location or emission rate and flux sensitivity matrices generated using the WRF-STILT atmospheric transport model. Transport model errors were assessed by comparing WRF-STILT wind speeds, wind direction and planetary boundary layer (PBL) height to those observed on the plane; the impact of these errors in the inversions, and the optimal inversion setup for reducing their influence was also explored. WRF-STILT provides a reasonable simulation of true atmospheric conditions on most flight dates, given the complex terrain and known difficulties in simulating atmospheric transport under such conditions. Moreover, even large (>120°) errors in wind direction were found to be tolerable in terms of spatially locating the leak rate within a 5-km radius of the actual site. Errors in the WRF-STILT wind speed (>50%) and PBL height have more negative impacts on the inversions, with too high wind speeds (typically corresponding with too low PBL heights) resulting in overestimated leak rates, and vice-versa. Coarser data averaging intervals and the use of observed wind speed errors in the model-data mismatch covariance matrix are shown to

  16. Mixing of a point-source indoor pollutant: Numerical predictions and comparison with experiments

    Energy Technology Data Exchange (ETDEWEB)

    Lobscheid, C.; Gadgil, A.J.

    2002-01-01

    In most practical estimates of indoor pollutant exposures, it is common to assume that the pollutant is uniformly and instantaneously mixed in the indoor space. It is also commonly known that this assumption is simplistic, particularly for point sources, and for short-term or localized indoor exposures. We report computational fluid dynamics (CFD) predictions of mixing time of a point-pulse release of a pollutant in an unventilated mechanically mixed isothermal room. We aimed to determine the adequacy of the standard RANS two-equation ({kappa}-{var_epsilon}) turbulence model to predict the mixing times under these conditions. The predictions were made for the twelve mixing time experiments performed by Drescher et al. (1995). We paid attention to adequate grid resolution, suppression of numerical diffusion, and careful simulation of the mechanical blowers used in the experiments. We found that the predictions are in good agreement with experimental measurements.

  17. A systematic analysis of the Braitenberg vehicle 2b for point-like stimulus sources

    International Nuclear Information System (INIS)

    Rañó, Iñaki

    2012-01-01

    Braitenberg vehicles have been used experimentally for decades in robotics with limited empirical understanding. This paper presents the first mathematical model of the vehicle 2b, displaying so-called aggression behaviour, and analyses the possible trajectories for point-like smooth stimulus sources. This sensory-motor steering control mechanism is used to implement biologically grounded target approach, target-seeking or obstacle-avoidance behaviour. However, the analysis of the resulting model reveals that complex and unexpected trajectories can result even for point-like stimuli. We also prove how the implementation of the controller and the vehicle morphology interact to affect the behaviour of the vehicle. This work provides a better understanding of Braitenberg vehicle 2b, explains experimental results and paves the way for a formally grounded application on robotics as well as for a new way of understanding target seeking in biology. (paper)

  18. Lippmann-Schwinger integral equation approach to the emission of radiation by sources located inside finite-sized dielectric structures

    DEFF Research Database (Denmark)

    Søndergaard, T.; Tromborg, Bjarne

    2002-01-01

    A full-vectorial integral equation method is presented for calculating near fields and far fields generated by a given distribution of sources located inside finite-sized dielectric structures. Special attention is given to the treatment of the singularity of the dipole source field. A method...... uses for analyzing the emission of light by sources in some antennas and optical components such as vertical cavity surface emitting lasers, microdisk lasers, and light emitting diodes. The methods also have prospective uses in quantum electrodynamics for studies of spontaneous emission from, e...

  19. Source contributions to PM2.5 and PM10 at an urban background and a street location

    NARCIS (Netherlands)

    Keuken, M. P.; Moerman, M.; Voogt, M.; Blom, M.; Weijers, E. P.; Rockmann, T.; Dusek, U.

    The contribution of regional, urban and traffic sources to PM2.5 and PM10 in an urban area was investigated in this study. The chemical composition of PM2.5 and PM10 was measured over a year at a street location and up- and down-wind of the city of Rotterdam, the Netherlands. The C-14 content in EC

  20. Source contributions to PM2.5 and PM10 at an urban background and a street location

    NARCIS (Netherlands)

    Keuken, M.; Moerman, M.; Voogt, M.; Blom, M.; Weijers, E.P.; Röckmann, T.; Dusek, U.

    2013-01-01

    The contribution of regional, urban and traffic sources to PM2.5 and PM10 in an urban area was investigated in this study. The chemical composition of PM2.5 and PM10 was measured over a year at a street location and up- and down-wind of the city of Rotterdam, the Netherlands. The 14C content in EC

  1. Tree Coring as a Complement to Soil Gas Screening to Locate PCE and TCE Source Zones and Hot Spots

    DEFF Research Database (Denmark)

    Nielsen, Mette Algreen; Trapp, Stefan; Rehne Jensen, Pernille

    2015-01-01

    ) or trichloroethylene (TCE) to evaluate their ability to locate source zones and contaminant hot spots. One test site represented a relatively homogeneous sandy soil and aquifer, and the second a more heterogeneous geology with both sandy and less permeable clay till layers overlying a chalk aquifer. Tree cores from...

  2. Effective doses in the radial gamma radiation field near a point source: gender difference and deviation from the personal dose equivalent

    International Nuclear Information System (INIS)

    Chang, Jai Kwon; Lee, Jai Ki

    1997-01-01

    The individual dose equivalent, H p , effective dose, E, and gender specific effective dose, E m , and E f , were evaluated using the male and female phantoms of MIRD type located in the radial gamma radiation field near a point source. The point sources were placed at the distances of 15, 40 and 100 cm in front of the body at different heights. Two radionuclides, 137 Cs and 131 I, were selected for the illustrative examples. In terms of the gender specific effective doses, E f is higher than E m with a few exceptions, e.g. the case where the point source is at the height of reproductive organs, but the differences from the sex- averaged values are not significant enough to justify use of gender specific dose conversion factors for the radial gamma field. The ratios H p /E were in the range of 1 to 3 depending on the source and dosimeter positions when the dosimeter is worn on the front surface of the torso covering from chest to lower abdomen, but varied from 0.34 to 6.5 in extreme cases. When it is assumed that the typical handling procedure of radioactive source material and the typical dosimeter position (on the chest) be respected, the dosimeters calibrated against the broad parallel field appear to provide estimates with acceptable errors for the effective dose of workers exposed to radial broad gamma field around a point source

  3. UHE γ-rays from point sources based on GRAPES-I observations

    International Nuclear Information System (INIS)

    Gupta, S.K.; Sreekantan, B.V.; Srivatsan, R.; Tonwar, S.C.

    1993-01-01

    An experiment called GRAPES I (Gamma Ray Astronomy at PeV EnergieS) was set up in 1984 at Ooty in India, using 24 scintillation counters, to detect Extensive Air Showers (EAS) produced in the atmosphere by the primary cosmic radiation. The goal of the experiment has been to search for Ultra High Energy (UHE) γ-rays (E≥10 14 eV) from point sources in the sky. Here we discuss the results on X-ray binaries CYG X-3, HER X-1 and SCO X-1 obtained with GRAPES I experiment which covers the period 1984--87

  4. Preliminary data summary for the pulp, paper and paperboard point source category

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-01

    The Preliminary Data Summary for the Pulp, Paper and Paperboard Point Source category is a collection of four documents: (1) Overview of the United States Pulp, Paper and Paperboard Industry and Production Processes (October 1987); (2) U.S. EPA/Paper Industry Cooperative Dioxin Screening Study (March 1988); (3) Statement of Martha G. Prothro, Director, Office of Water Regulations and Standards, before the Subcommittee on Water Resources of the Committee on Public Works and Transportation, U.S. House of Representatives (July 13, 1988); (4) U.S. EPA/Paper Industry Cooperative Dioxin Study, Analytical Results (June 16, 1989).

  5. Locating sensors for detecting source-to-target patterns of special nuclear material smuggling: a spatial information theoretic approach.

    Science.gov (United States)

    Przybyla, Jay; Taylor, Jeffrey; Zhou, Xuesong

    2010-01-01

    In this paper, a spatial information-theoretic model is proposed to locate sensors for detecting source-to-target patterns of special nuclear material (SNM) smuggling. In order to ship the nuclear materials from a source location with SNM production to a target city, the smugglers must employ global and domestic logistics systems. This paper focuses on locating a limited set of fixed and mobile radiation sensors in a transportation network, with the intent to maximize the expected information gain and minimize the estimation error for the subsequent nuclear material detection stage. A Kalman filtering-based framework is adapted to assist the decision-maker in quantifying the network-wide information gain and SNM flow estimation accuracy.

  6. Locating Sensors for Detecting Source-to-Target Patterns of Special Nuclear Material Smuggling: A Spatial Information Theoretic Approach

    Directory of Open Access Journals (Sweden)

    Xuesong Zhou

    2010-08-01

    Full Text Available In this paper, a spatial information-theoretic model is proposed to locate sensors for detecting source-to-target patterns of special nuclear material (SNM smuggling. In order to ship the nuclear materials from a source location with SNM production to a target city, the smugglers must employ global and domestic logistics systems. This paper focuses on locating a limited set of fixed and mobile radiation sensors in a transportation network, with the intent to maximize the expected information gain and minimize the estimation error for the subsequent nuclear material detection stage. A Kalman filtering-based framework is adapted to assist the decision-maker in quantifying the network-wide information gain and SNM flow estimation accuracy.

  7. A method for untriggered time-dependent searches for multiple flares from neutrino point sources

    International Nuclear Information System (INIS)

    Gora, D.; Bernardini, E.; Cruz Silva, A.H.

    2011-04-01

    A method for a time-dependent search for flaring astrophysical sources which can be potentially detected by large neutrino experiments is presented. The method uses a time-clustering algorithm combined with an unbinned likelihood procedure. By including in the likelihood function a signal term which describes the contribution of many small clusters of signal-like events, this method provides an effective way for looking for weak neutrino flares over different time-scales. The method is sensitive to an overall excess of events distributed over several flares which are not individually detectable. For standard cases (one flare) the discovery potential of the method is worse than a standard time-dependent point source analysis with unknown duration of the flare by a factor depending on the signal-to-background level. However, for flares sufficiently shorter than the total observation period, the method is more sensitive than a time-integrated analysis. (orig.)

  8. A method for untriggered time-dependent searches for multiple flares from neutrino point sources

    Energy Technology Data Exchange (ETDEWEB)

    Gora, D. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Institute of Nuclear Physics PAN, Cracow (Poland); Bernardini, E.; Cruz Silva, A.H. [Institute of Nuclear Physics PAN, Cracow (Poland)

    2011-04-15

    A method for a time-dependent search for flaring astrophysical sources which can be potentially detected by large neutrino experiments is presented. The method uses a time-clustering algorithm combined with an unbinned likelihood procedure. By including in the likelihood function a signal term which describes the contribution of many small clusters of signal-like events, this method provides an effective way for looking for weak neutrino flares over different time-scales. The method is sensitive to an overall excess of events distributed over several flares which are not individually detectable. For standard cases (one flare) the discovery potential of the method is worse than a standard time-dependent point source analysis with unknown duration of the flare by a factor depending on the signal-to-background level. However, for flares sufficiently shorter than the total observation period, the method is more sensitive than a time-integrated analysis. (orig.)

  9. Development of uniform hazard response spectra for rock sites considering line and point sources of earthquakes

    International Nuclear Information System (INIS)

    Ghosh, A.K.; Kushwaha, H.S.

    2001-12-01

    Traditionally, the seismic design basis ground motion has been specified by normalised response spectral shapes and peak ground acceleration (PGA). The mean recurrence interval (MRI) used to computed for PGA only. It is shown that the MRI associated with such response spectra are not the same at all frequencies. The present work develops uniform hazard response spectra i.e. spectra having the same MRI at all frequencies for line and point sources of earthquakes by using a large number of strong motion accelerograms recorded on rock sites. Sensitivity of the number of the results to the changes in various parameters has also been presented. This work is an extension of an earlier work for aerial sources of earthquakes. These results will help to determine the seismic hazard at a given site and the associated uncertainities. (author)

  10. Decreasing Computational Time for VBBinaryLensing by Point Source Approximation

    Science.gov (United States)

    Tirrell, Bethany M.; Visgaitis, Tiffany A.; Bozza, Valerio

    2018-01-01

    The gravitational lens of a binary system produces a magnification map that is more intricate than a single object lens. This map cannot be calculated analytically and one must rely on computational methods to resolve. There are generally two methods of computing the microlensed flux of a source. One is based on ray-shooting maps (Kayser, Refsdal, & Stabell 1986), while the other method is based on an application of Green’s theorem. This second method finds the area of an image by calculating a Riemann integral along the image contour. VBBinaryLensing is a C++ contour integration code developed by Valerio Bozza, which utilizes this method. The parameters at which the source object could be treated as a point source, or in other words, when the source is far enough from the caustic, was of interest to substantially decrease the computational time. The maximum and minimum values of the caustic curves produced, were examined to determine the boundaries for which this simplification could be made. The code was then run for a number of different maps, with separation values and accuracies ranging from 10-1 to 10-3, to test the theoretical model and determine a safe buffer for which minimal error could be made for the approximation. The determined buffer was 1.5+5q, with q being the mass ratio. The theoretical model and the calculated points worked for all combinations of the separation values and different accuracies except the map with accuracy and separation equal to 10-3 for y1 max. An alternative approach has to be found in order to accommodate a wider range of parameters.

  11. Bayesian inverse modeling and source location of an unintended 131I release in Europe in the fall of 2011

    Science.gov (United States)

    Tichý, Ondřej; Šmídl, Václav; Hofman, Radek; Šindelářová, Kateřina; Hýža, Miroslav; Stohl, Andreas

    2017-10-01

    In the fall of 2011, iodine-131 (131I) was detected at several radionuclide monitoring stations in central Europe. After investigation, the International Atomic Energy Agency (IAEA) was informed by Hungarian authorities that 131I was released from the Institute of Isotopes Ltd. in Budapest, Hungary. It was reported that a total activity of 342 GBq of 131I was emitted between 8 September and 16 November 2011. In this study, we use the ambient concentration measurements of 131I to determine the location of the release as well as its magnitude and temporal variation. As the location of the release and an estimate of the source strength became eventually known, this accident represents a realistic test case for inversion models. For our source reconstruction, we use no prior knowledge. Instead, we estimate the source location and emission variation using only the available 131I measurements. Subsequently, we use the partial information about the source term available from the Hungarian authorities for validation of our results. For the source determination, we first perform backward runs of atmospheric transport models and obtain source-receptor sensitivity (SRS) matrices for each grid cell of our study domain. We use two dispersion models, FLEXPART and Hysplit, driven with meteorological analysis data from the global forecast system (GFS) and from European Centre for Medium-range Weather Forecasts (ECMWF) weather forecast models. Second, we use a recently developed inverse method, least-squares with adaptive prior covariance (LS-APC), to determine the 131I emissions and their temporal variation from the measurements and computed SRS matrices. For each grid cell of our simulation domain, we evaluate the probability that the release was generated in that cell using Bayesian model selection. The model selection procedure also provides information about the most suitable dispersion model for the source term reconstruction. Third, we select the most probable location of

  12. Bayesian inverse modeling and source location of an unintended 131I release in Europe in the fall of 2011

    Directory of Open Access Journals (Sweden)

    O. Tichý

    2017-10-01

    Full Text Available In the fall of 2011, iodine-131 (131I was detected at several radionuclide monitoring stations in central Europe. After investigation, the International Atomic Energy Agency (IAEA was informed by Hungarian authorities that 131I was released from the Institute of Isotopes Ltd. in Budapest, Hungary. It was reported that a total activity of 342 GBq of 131I was emitted between 8 September and 16 November 2011. In this study, we use the ambient concentration measurements of 131I to determine the location of the release as well as its magnitude and temporal variation. As the location of the release and an estimate of the source strength became eventually known, this accident represents a realistic test case for inversion models. For our source reconstruction, we use no prior knowledge. Instead, we estimate the source location and emission variation using only the available 131I measurements. Subsequently, we use the partial information about the source term available from the Hungarian authorities for validation of our results. For the source determination, we first perform backward runs of atmospheric transport models and obtain source-receptor sensitivity (SRS matrices for each grid cell of our study domain. We use two dispersion models, FLEXPART and Hysplit, driven with meteorological analysis data from the global forecast system (GFS and from European Centre for Medium-range Weather Forecasts (ECMWF weather forecast models. Second, we use a recently developed inverse method, least-squares with adaptive prior covariance (LS-APC, to determine the 131I emissions and their temporal variation from the measurements and computed SRS matrices. For each grid cell of our simulation domain, we evaluate the probability that the release was generated in that cell using Bayesian model selection. The model selection procedure also provides information about the most suitable dispersion model for the source term reconstruction. Third, we select the most

  13. Semi analytical solution of point kinetic equation with source from cold start up to delayed critical

    International Nuclear Information System (INIS)

    Sathiyasheela, T.

    2009-01-01

    Point kinetics equations (P. K. E) are system of differential equations, which is solved simultaneously to get the neutron density as a function of time for a given reactivity input. P. K. E are stiff differential equations, computational solution through the conventional explicit method will give a stable consistent result only for smaller time steps. Analytical solutions are available either with step or ramp reactivity insertion without considering the source power contribution. When a reactor operates at low power, the neutron source gives a considerable contribution to the net reactor power. Similarly, when the reactor is brought to delayed critical with the presence of external source, the sub critical reactor kinetics studies with source power are important to understand the power behavior as a function of reactivity insertion rate with respect to the initial reactivity. In the present work, P.K.E with one group delayed neutron are solved analytically to determine the reactor power as a function of reactivity insertion rate in the presence of neutron source. The analytical solution is a combination of converging two infinite series. Truncated infinite series is the analytical solution of P.K E. A general formulation is made by Combining both the ramp reactivity and step reactivity solution. So that the analytical solution could be useful in analyzing either step and ramp reactivity insertion exclusively or the combination of both. This general formulation could be useful in analyzing many reactor operations, like the air bubble passing through the core, stuck rod conditions, uncontrolled withdrawal of controlled rod, discontinuous lifting of control rod, lowering of rod and etc. Results of analytical solutions are compared against the results of numerical solution which is developed based on Cohen's method. The comparisons are found to be good for all kind of positive and negative ramp reactivity insertions, with or without the combination of step reactivity

  14. Data library of gamma-ray buildup factors for point isotropic source

    International Nuclear Information System (INIS)

    Sakamoto, Yukio; Tanaka, Shun-ichi; Harima, Yoshiko.

    1988-01-01

    Gamma-ray buildup factors for a point isotropic source have been calculated as a function of atomic number of heavy elements and source energies over an energy range from 0.015 MeV to 15 MeV, for penetration depths up to 40 mfp, bu the PALLAS-PL,SP-Br code. These data include the contribution of bremsstrahlung, annihilation radiation and fluorescence X-ray. The calculated absorbed-dose, exposure and dose-equivalent buildup factors are tabulated for molybdenum, tin, tungsten, lead and uranium, which are practical interest shield materials, lanthanum and gadolinium which are important materials for obtaining buildup factors by interpolation with the atomic number. In the case of high atomic number materials, inclusion of brems-strahlung source has great influence on the buildup factors for high source energies and that of fluorescence X-ray gives spectracular effects on those for low energies close to the K edge of attenuation cross section. Furthermore, the geometrical-progression (G-P) parameters have been determined for these buildup factors in order to obtain the values of buildup factors at arbitrary distances and energies. (author)

  15. Neon dense plasma focus point x-ray source for <= 0.25 um lithography

    Science.gov (United States)

    Prasad, Rahul R.; Krishnan, Mahadevan; Mangano, Joseph; Greene, Philip A.; Qi, Niansheng

    1994-05-01

    A discharge driven, dense plasma focus (DPF) in Neon has been developed at SRL as a point x-ray source for sub-micron lithography. This source is presently capable of delivering approximately 25 J/pulse of Neon K-shell x rays (8 - 14 angstrom) into 4 (pi) steradians with an approximately equals 1.4% wall plug efficiency at a 20 Hz repetition rate. This corresponds to 500 W of average x-ray power. The discharge is produced by a capacitor bank circuit (8 kV, 1.8 kJ) that drives approximately equals 320 kA currents into the DPF load, with approximately equals 1 microsecond(s) rise-times. X rays are produced when a dense pinch of Neon is formed along the axis of the DPF electrodes. Four X ten5 discharges using a cooled DPF head have been fired producing x rays. The variation in the measured x-ray output, over several 104 shots, corresponds to a variation in the dose delivered to a resist 40 cm from the source, of less than 1%. Data showing the measurement of the x-ray output, size, dose delivered to a resist, spectra of the source output, novel beam line concepts, and potential lithographic applications are discussed.

  16. Point, surface and volumetric heat sources in the thermal modelling of selective laser melting

    Science.gov (United States)

    Yang, Yabin; Ayas, Can

    2017-10-01

    Selective laser melting (SLM) is a powder based additive manufacturing technique suitable for producing high precision metal parts. However, distortions and residual stresses within products arise during SLM because of the high temperature gradients created by the laser heating. Residual stresses limit the load resistance of the product and may even lead to fracture during the built process. It is therefore of paramount importance to predict the level of part distortion and residual stress as a function of SLM process parameters which requires a reliable thermal modelling of the SLM process. Consequently, a key question arises which is how to describe the laser source appropriately. Reasonable simplification of the laser representation is crucial for the computational efficiency of the thermal model of the SLM process. In this paper, first a semi-analytical thermal modelling approach is described. Subsequently, the laser heating is modelled using point, surface and volumetric sources, in order to compare the influence of different laser source geometries on the thermal history prediction of the thermal model. The present work provides guidelines on appropriate representation of the laser source in the thermal modelling of the SLM process.

  17. Location of odor sources and the affected population in Imperial County, California

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, J.L.

    1981-08-01

    This report is divided into four sections. The first two sections contain general background information on Imperial County. The third section is a general discussion of odor sources in Imperial County, and the fourth maps the specific odor sources, the expected areas of perception, and the affected populations. this mapping is done for the Imperial Valley and each of the four Imperial County KGRA's (Known Geothermal Resource Areas) where odor from the development of the geothermal energy may affect population.

  18. Enigmatic X-Ray Sources Point to Possible New Black Hole Population

    Science.gov (United States)

    2004-03-01

    Mysterious, powerful X-ray sources found in nearby galaxies may represent a new class of objects, according to data from NASA's Chandra X-ray Observatory. These sources, which are not as hot as typical neutron-star or black-hole X- ray sources, could be a large new population of black holes with masses several hundred times that of the sun. "The challenge raised by the discovery of these sources is to understand how they produce so much X-ray power at temperatures of a few million degrees," said Rosanne Di Stefano from the Harvard-Smithsonian Center for Astrophysics in Cambridge, Mass., and Tufts University in Medford, Mass. Di Stefano is lead author of a series of papers published in or submitted to The Astrophysical Journal and The Astrophysical Journal Letters. Until a few years ago, astronomers only knew of two sizes of black holes: stellar black holes, with masses about 10 times the sun, and supermassive black holes located at the centers of galaxies, with masses ranging from millions to billions times the sun. Recent evidence suggests a class of "intermediate- mass" black holes may also exist. M83 M83 Searching for quasisoft sources may be a new way to identify those X-ray sources most likely to be intermediate-mass black holes," said Albert Kong of the Center for Astrophysics (CfA) and a member of the team. The enigmatic objects found by the Chandra team are called "quasisoft" sources, because they have a temperature in the range of 1 million to 4 million degrees Celsius. On the one hand this temperature range is below the 10 million to 100 million-degree gas associated with "hard" X-ray sources, such as neutron stars or stellar-mass black holes. On the other hand the quasisoft-source temperatures are hotter than the several hundred-thousand-degree gas associated with "supersoft" X-ray sources due to white dwarfs. M51 M51 Di Stefano and her colleagues determined the temperatures of individual X-ray emitting objects in four galaxies by measuring their X

  19. Using web-sources for location based systems on mobile phones

    NARCIS (Netherlands)

    Pannevis, M.; Marx, M.

    2008-01-01

    The paper describes the implementation of a context aware location and time based system on a normal mobile phone, with a minimum of requirements (Bluetooth, Internet access, Java ME, and a simple webbrowser). We can answer the following queries based on data crawled from the web and enriched with

  20. Estimating the size of a methane emission point source at different scales: from local to landscape

    Science.gov (United States)

    Riddick, Stuart N.; Connors, Sarah; Robinson, Andrew D.; Manning, Alistair J.; Jones, Pippa S. D.; Lowry, David; Nisbet, Euan; Skelton, Robert L.; Allen, Grant; Pitt, Joseph; Harris, Neil R. P.

    2017-06-01

    High methane (CH4) mixing ratios (up to 4 ppm) have occurred sporadically at our measurement site in Haddenham, Cambridgeshire, since July 2012. Isotopic measurements and back trajectories show that the source is the Waterbeach Waste Management Park 7 km SE of Haddenham. To investigate this further, measurements were made on 30 June and 1 July 2015 at other locations nearer to the source. Landfill emissions have been estimated using three different approaches at different scales; near source using the WindTrax inversion dispersion model, middle distance using a Gaussian plume (GP) model and at the landscape scale using the Numerical Atmospheric Modelling Environment (NAME) Inversion Technique for Emission Modelling (InTEM) inversion. The emission estimates derived using the WindTrax and Gaussian plume (GP) approaches agree well for the period of intense observations. Applying the Gaussian plume approach to all periods of elevated measurements seen at Haddenham produces year-round and monthly landfill emission estimates with an estimated annual emission of 11.6 Gg CH4 yr-1. The monthly emission estimates are highest in winter (2160 kg h-1 in February) and lowest in summer (620 kg h-1 in July). These data identify the effects of environmental conditions on landfill CH4 production and highlight the importance of year-round measurements to capture seasonal variability in CH4 emission.

  1. Correlation of Traditional Point a With Anatomic Location of Uterine Artery and Ureter in Cancer of the Uterine Cervix

    International Nuclear Information System (INIS)

    Wang, K.-L.; Yang, Y.-C.; Chao, K. S. Clifford; Wu, M.-H.; Tai, H.-C.; Chen, T.-C.; Huang, M.-C.; Chen, J.-R.; Su, T.-H.; Chen, Y.-J.

    2007-01-01

    Purpose: Point A, used for dose specification for intracavitary brachytherapy for cervical cancer, is the point at which the uterine artery and ureter cross. This study assessed compatibility of commonly used traditional point A (TPA) and actual anatomic point A (APA). Methods and Materials: We visualized and placed radiopaque clips at the APA during pelvic and paraaortic lymphadenectomy in 11 patients with cervical carcinoma. Orthogonal and oblique radiographs were obtained after insertion of brachytherapy applicators. We measured the distance between the TPA and APA and estimated the brachytherapy dose to each of the two points. Results: A total of 64 brachytherapy treatments were performed. The mean distances between the TPA and APA were 5.2 ± 1.0 cm on the right and 5.4 ± 1.1 cm on the left. The estimated brachytherapy doses delivered to the APA as a percentage of the presumed 500-cGy fraction size to the TPA were 35.2% (176.6 ± 59.0 cGy) on the right and 30.0% (150.2 ± 42.9 cGy) on the left. The marked discrepancy in the position of the two points was not related to individual kinetic variations during brachytherapy treatment, tumor size, or bladder filling. Conclusions: The conventional TPA does not provide an accurate estimate of the APA determined during lymphadenectomy, indicating a need to reevaluate the current practice for determining the brachytherapy prescription for cervical cancer. ( (ClinicalTrials.gov) Identifier, NCT00319462)

  2. Emissions of perfluorinated alkylated substances (PFAS) from point sources--identification of relevant branches.

    Science.gov (United States)

    Clara, M; Scheffknecht, C; Scharf, S; Weiss, S; Gans, O

    2008-01-01

    Effluents of wastewater treatment plants are relevant point sources for the emission of hazardous xenobiotic substances to the aquatic environment. One group of substances, which recently entered scientific and political discussions, is the group of the perfluorinated alkylated substances (PFAS). The most studied compounds from this group are perfluorooctanoic acid (PFOA) and perfluorooctane sulphonate (PFOS), which are the most important degradation products of PFAS. These two substances are known to be persistent, bioaccumulative and toxic (PBT). In the present study, eleven PFAS were investigated in effluents of municipal wastewater treatment plants (WWTP) and in industrial wastewaters. PFOS and PFOA proved to be the dominant compounds in all sampled wastewaters. Concentrations of up to 340 ng/L of PFOS and up to 220 ng/L of PFOA were observed. Besides these two compounds, perfluorohexanoic acid (PFHxA) was also present in nearly all effluents and maximum concentrations of up to 280 ng/L were measured. Only N-ethylperfluorooctane sulphonamide (N-EtPFOSA) and its degradation/metabolisation product perfluorooctane sulphonamide (PFOSA) were either detected below the limit of quantification or were not even detected at all. Beside the effluents of the municipal WWTPs, nine industrial wastewaters from six different industrial branches were also investigated. Significantly, the highest emissions or PFOS were observed from metal industry whereas paper industry showed the highest PFOA emission. Several PFAS, especially perfluorononanoic acid (PFNA), perfluorodecanoic acid (PFDA), perfluorododecanoic acid (PFDoA) and PFOS are predominantly emitted from industrial sources, with concentrations being a factor of 10 higher than those observed in the municipal WWTP effluents. Perfluorodecane sulphonate (PFDS), N-Et-PFOSA and PFOSA were not detected in any of the sampled industrial point sources. (c) IWA Publishing 2008.

  3. Source location in plates based on the multiple sensors array method and wavelet analysis

    International Nuclear Information System (INIS)

    Yang, Hong Jun; Shin, Tae Jin; Lee, Sang Kwon

    2014-01-01

    A new method for impact source localization in a plate is proposed based on the multiple signal classification (MUSIC) and wavelet analysis. For source localization, the direction of arrival of the wave caused by an impact on a plate and the distance between impact position and sensor should be estimated. The direction of arrival can be estimated accurately using MUSIC method. The distance can be obtained by using the time delay of arrival and the group velocity of the Lamb wave in a plate. Time delay is experimentally estimated using the continuous wavelet transform for the wave. The elasto dynamic theory is used for the group velocity estimation.

  4. 49 CFR Figure 3 to Subpart B of... - Example of Location and Marking of Structural Weak Points on Roof of Passenger Car-§ 238.123

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Example of Location and Marking of Structural Weak Points on Roof of Passenger Car-§ 238.123 3 Figure 3 to Subpart B of Part 238 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF...

  5. Fast computation of quadrupole and hexadecapole approximations in microlensing with a single point-source evaluation

    Science.gov (United States)

    Cassan, Arnaud

    2017-07-01

    The exoplanet detection rate from gravitational microlensing has grown significantly in recent years thanks to a great enhancement of resources and improved observational strategy. Current observatories include ground-based wide-field and/or robotic world-wide networks of telescopes, as well as space-based observatories such as satellites Spitzer or Kepler/K2. This results in a large quantity of data to be processed and analysed, which is a challenge for modelling codes because of the complexity of the parameter space to be explored and the intensive computations required to evaluate the models. In this work, I present a method that allows to compute the quadrupole and hexadecapole approximations of the finite-source magnification with more efficiency than previously available codes, with routines about six times and four times faster, respectively. The quadrupole takes just about twice the time of a point-source evaluation, which advocates for generalizing its use to large portions of the light curves. The corresponding routines are available as open-source python codes.

  6. IceCube results from point-like source searches using seven years of through-going muon data

    Energy Technology Data Exchange (ETDEWEB)

    Coenders, Stefan; Resconi, Elisa [Technische Universitaet Muenchen, Boltzmannstr. 2, 85748 Garching (Germany); Collaboration: IceCube-Collaboration

    2016-07-01

    The IceCube Neutrino Observatory located at the geographic South Pole was designed to study and discover high-energy neutrinos coming from both galactic and extragalactic sources. Track-like events induced by charged-current muon-neutrino interactions close to the IceCube detector give an angular resolution better than 1 degree above TeV energies. Within seven years of detector lifetime, IceCube selects more than 700,000 events over the full sky, plus an additional component of almost 1000 events that are identified to be starting in the detector in the southern sky. Using this event sample, IceCube is sensitive to a steady neutrino flux substantially below E{sup 2} ∂ φ/∂ E = 10{sup -12} TeV cm{sup -2} s{sup -1} in the northern sky for neutrino energies above 10 TeV. We report about the results in this search for steady point-like neutrino sources.

  7. Quantitative assessment of distance to collection point and improved sorting information on source separation of household waste.

    Science.gov (United States)

    Rousta, Kamran; Bolton, Kim; Lundin, Magnus; Dahlén, Lisa

    2015-06-01

    The present study measures the participation of households in a source separation scheme and, in particular, if the household's application of the scheme improved after two interventions: (a) shorter distance to the drop-off point and (b) easy access to correct sorting information. The effect of these interventions was quantified and, as far as possible, isolated from other factors that can influence the recycling behaviour. The study was based on households located in an urban residential area in Sweden, where waste composition studies were performed before and after the interventions by manual sorting (pick analysis). Statistical analyses of the results indicated a significant decrease (28%) of packaging and newsprint in the residual waste after establishing a property close collection system (intervention (a)), as well as significant decrease (70%) of the miss-sorted fraction in bags intended for food waste after new information stickers were introduced (intervention (b)). Providing a property close collection system to collect more waste fractions as well as finding new communication channels for information about sorting can be used as tools to increase the source separation ratio. This contribution also highlights the need to evaluate the effects of different types of information and communication concerning sorting instructions in a property close collection system. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. DEVELOPMENT OF THE MODEL OF GALACTIC INTERSTELLAR EMISSION FOR STANDARD POINT-SOURCE ANALYSIS OF FERMI LARGE AREA TELESCOPE DATA

    Energy Technology Data Exchange (ETDEWEB)

    Acero, F.; Ballet, J. [Laboratoire AIM, CEA-IRFU/CNRS/Université Paris Diderot, Service d’Astrophysique, CEA Saclay, F-91191 Gif sur Yvette (France); Ackermann, M.; Buehler, R. [Deutsches Elektronen Synchrotron DESY, D-15738 Zeuthen (Germany); Ajello, M. [Department of Physics and Astronomy, Clemson University, Kinard Lab of Physics, Clemson, SC 29634-0978 (United States); Albert, A.; Baldini, L.; Bloom, E. D.; Bottacini, E.; Caliandro, G. A.; Cameron, R. A. [W. W. Hansen Experimental Physics Laboratory, Kavli Institute for Particle Astrophysics and Cosmology, Department of Physics and SLAC National Accelerator Laboratory, Stanford University, Stanford, CA 94305 (United States); Barbiellini, G. [Istituto Nazionale di Fisica Nucleare, Sezione di Trieste, I-34127 Trieste (Italy); Bastieri, D. [Istituto Nazionale di Fisica Nucleare, Sezione di Padova, I-35131 Padova (Italy); Bellazzini, R. [Istituto Nazionale di Fisica Nucleare, Sezione di Pisa, I-56127 Pisa (Italy); Bissaldi, E. [Istituto Nazionale di Fisica Nucleare, Sezione di Bari, I-70126 Bari (Italy); Bonino, R. [Istituto Nazionale di Fisica Nucleare, Sezione di Torino, I-10125 Torino (Italy); Brandt, T. J.; Buson, S. [NASA Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Bregeon, J. [Laboratoire Univers et Particules de Montpellier, Université Montpellier, CNRS/IN2P3, Montpellier (France); Bruel, P., E-mail: isabelle.grenier@cea.fr, E-mail: casandjian@cea.fr [Laboratoire Leprince-Ringuet, École polytechnique, CNRS/IN2P3, Palaiseau (France); and others

    2016-04-01

    Most of the celestial γ rays detected by the Large Area Telescope (LAT) on board the Fermi Gamma-ray Space Telescope originate from the interstellar medium when energetic cosmic rays interact with interstellar nucleons and photons. Conventional point-source and extended-source studies rely on the modeling of this diffuse emission for accurate characterization. Here, we describe the development of the Galactic Interstellar Emission Model (GIEM), which is the standard adopted by the LAT Collaboration and is publicly available. This model is based on a linear combination of maps for interstellar gas column density in Galactocentric annuli and for the inverse-Compton emission produced in the Galaxy. In the GIEM, we also include large-scale structures like Loop I and the Fermi bubbles. The measured gas emissivity spectra confirm that the cosmic-ray proton density decreases with Galactocentric distance beyond 5 kpc from the Galactic Center. The measurements also suggest a softening of the proton spectrum with Galactocentric distance. We observe that the Fermi bubbles have boundaries with a shape similar to a catenary at latitudes below 20° and we observe an enhanced emission toward their base extending in the north and south Galactic directions and located within ∼4° of the Galactic Center.

  9. Development of the Model of Galactic Interstellar Emission for Standard Point-Source Analysis of Fermi Large Area Telescope Data

    Science.gov (United States)

    Acero, F.; Ackermann, M.; Ajello, M.; Albert, A.; Baldini, L.; Ballet, J.; Barbiellini, G.; Bastieri, D.; Bellazzini, R.; Brandt, T. J.; hide

    2016-01-01

    Most of the celestial gamma rays detected by the Large Area Telescope (LAT) on board the Fermi Gamma-ray Space Telescope originate from the interstellar medium when energetic cosmic rays interact with interstellar nucleons and photons. Conventional point-source and extended-source studies rely on the modeling of this diffuse emission for accurate characterization. Here, we describe the development of the Galactic Interstellar Emission Model (GIEM),which is the standard adopted by the LAT Collaboration and is publicly available. This model is based on a linear combination of maps for interstellar gas column density in Galactocentric annuli and for the inverse-Compton emission produced in the Galaxy. In the GIEM, we also include large-scale structures like Loop I and the Fermi bubbles. The measured gas emissivity spectra confirm that the cosmic-ray proton density decreases with Galactocentric distance beyond 5 kpc from the Galactic Center. The measurements also suggest a softening of the proton spectrum with Galactocentric distance. We observe that the Fermi bubbles have boundaries with a shape similar to a catenary at latitudes below 20deg and we observe an enhanced emission toward their base extending in the north and south Galactic directions and located within approximately 4deg of the Galactic Center.

  10. Crowd-Sourced Mobility Mapping for Location Tracking Using Unlabeled Wi-Fi Simultaneous Localization and Mapping

    Directory of Open Access Journals (Sweden)

    Mu Zhou

    2015-01-01

    Full Text Available Due to the increasing requirements of the seamless and round-the-clock Location-based services (LBSs, a growing interest in Wi-Fi network aided location tracking is witnessed in the past decade. One of the significant problems of the conventional Wi-Fi location tracking approaches based on received signal strength (RSS fingerprinting is the time-consuming and labor intensive work involved in location fingerprint calibration. To solve this problem, a novel unlabeled Wi-Fi simultaneous localization and mapping (SLAM approach is developed to avoid the location fingerprinting and additional inertial or vision sensors. In this approach, an unlabeled mobility map of the coverage area is first constructed by using the crowd-sourcing from a batch of sporadically recorded Wi-Fi RSS sequences based on the spectral cluster assembling. Then, the sequence alignment algorithm is applied to conduct location tracking and mobility map updating. Finally, the effectiveness of this approach is verified by the extensive experiments carried out in a campus-wide area.

  11. The Newtonian force experienced by a point mass near a finite cylindrical source

    International Nuclear Information System (INIS)

    Selvaggi, Jerry P; Salon, Sheppard; Chari, M V K

    2008-01-01

    The Newtonian gravitational force experienced by a point mass located at some external point from a thick-walled, hollow and uniform finite circular cylindrical body was recently solved by Lockerbie, Veryaskin and Xu (1993 Class. Quantum Grav. 10 2419). Their method of attack relied on the introduction of the circular cylindrical free-space Green function representation for the inverse distance which appears in the formulation of the Newtonian potential function. This ultimately leads Lockerbie et al to a final expression for the Newtonian potential function which is expressed as a double summation of even-ordered Legendre polynomials. However, the kernel of the cylindrical free-space Green function which is represented by an infinite integral of the product of two Bessel functions and a decaying exponential can be analytically evaluated in terms of a toroidal function. This leads to a simplification in the mathematical analysis developed by Lockerbie et al. Also, each term in the infinite series solution for the Newtonian potential function can be expressed in closed form in terms of elementary functions. The authors develop the Newtonian potential function by employing toroidal functions of zeroth order or Legendre functions of half-integral degree, Q m-1/2 (β)(Bouwkamp and de Bruijn 1947 J. Appl. Phys.18 562, Cohl et al 2001 Phys. Rev.A 64 052509-1, Selvaggi et al 2004 IEEE Trans. Magn.40 3278). These functions are monotonically decreasing and converge rapidly (Moon and Spencer 1961 Field Theory for Engineers (New Jersey: Van Nostrand Company) pp 368-76, Cohl and Tohline 1999 Astrophys. J.527 86). The introduction of the toroidal harmonic expansion leads to an infinite series solution for which each term can be expressed as an elementary function. This enables one to easily compute the axial and radial forces experienced by an internal or an external point mass

  12. Impacts of Reverberation Time, Absorption Location and Background Noise on Listening Conditions in Multi Source Environment

    DEFF Research Database (Denmark)

    Saher, Konca; Rindel, Jens Holger; Nijs, Lau

    2005-01-01

    This paper is part of a PhD research project focusing on the prediction of the acoustical quality in living rooms and workspaces in institutions for mentally challenged people. One of the important activities in these rooms is simultaneous conversations. In this respect, the speech intelligibility...... index (STI) needs to be improved. The impact of the reverberation time (RT), the distribution of the absorptive materials and the introduction of a screen on STI are discussed briefly .However, these objective parameters have to be assessed through subjective judgement. Auralizations of the multi source...... environment are done according to different reverberation and absorption (with and without a screen) conditions. Then listening tests with the subjects are accomplished. The results indicate that the judgment of reverberation; loudness and type of noise source and its impact on speech intelligibility...

  13. Locating the Tohoku-Oki 2011 tsunami source using acoustic-gravity waves

    OpenAIRE

    Andriamiranto Raveloson; Rainer Kind; Xiaohui Yuan; L. Cerana

    2012-01-01

    The giant Tohoku-Oki earthquake of 11 March 2011 in offshore Japan did not only generate tsunami waves in the ocean but also infrasound (or acoustic-gravity) waves in the atmosphere. We indentified ultra-long-period signals (>500s) in the recordings of infrasound stations in northeast Asia, the northwest Pacific, and Alaska. Their source was fond close to the earthquake epicenter. Therefore, we conclude that in general, infrasound observations after a large offshore earthquake are evidence th...

  14. Application ofarrival time profiles to AE source location by neural networks

    Czech Academy of Sciences Publication Activity Database

    Chlada, Milan; Blaháček, Michal; Převorovský, Zdeněk

    2009-01-01

    Roč. 19, č. 3 (2009), s. 13-13 ISSN 1213-3825. [DEFEKTOSKOPIE 2009. 04.11.2009-06.11.2009, Praha] R&D Projects: GA ČR GA106/07/1393; GA ČR GA101/07/1518 Institutional research plan: CEZ:AV0Z20760514 Keywords : acoustic emission * arrival time profiles * source localization * neural networks Subject RIV: BI - Acoustics

  15. Source Apportionment of Particle Bound Polycyclic Aromatic Hydrocarbons at an Industrial Location in Agra, India

    Science.gov (United States)

    Lakhani, Anita

    2012-01-01

    16 US EPA priority polycyclic aromatic hydrocarbons (PAHs) were quantified in total suspended ambient particulate matter (TSPM) collected from an industrial site in Agra (India) using gas chromatography. The major industrial activities in Agra are foundries that previously used coal and coke as fuel in cupola furnaces. These foundries have now switched over to natural gas. In addition, use of compressed natural gas has also been promoted and encouraged in automobiles. This study attempts to apportion sources of PAH in the ambient air and the results reflect the advantages associated with the change of fuel. The predominant PAHs in TSPM include high molecular weight (HMW) congeners BghiP, DbA, IP, and BaP. The sum of 16 priority PAHs had a mean value of 72.7 ± 4.7 ng m−3. Potential sources of PAHs in aerosols were identified using diagnostic ratios and principal component analysis. The results reflect a blend of emissions from diesel and natural gas as the major sources of PAH in the city along with contribution from emission of coal, coke, and gasoline. PMID:22606062

  16. Source Apportionment of Particle Bound Polycyclic Aromatic Hydrocarbons at an Industrial Location in Agra, India

    Directory of Open Access Journals (Sweden)

    Anita Lakhani

    2012-01-01

    Full Text Available 16 US EPA priority polycyclic aromatic hydrocarbons (PAHs were quantified in total suspended ambient particulate matter (TSPM collected from an industrial site in Agra (India using gas chromatography. The major industrial activities in Agra are foundries that previously used coal and coke as fuel in cupola furnaces. These foundries have now switched over to natural gas. In addition, use of compressed natural gas has also been promoted and encouraged in automobiles. This study attempts to apportion sources of PAH in the ambient air and the results reflect the advantages associated with the change of fuel. The predominant PAHs in TSPM include high molecular weight (HMW congeners BghiP, DbA, IP, and BaP. The sum of 16 priority PAHs had a mean value of 72.7 ± 4.7 ng m−3. Potential sources of PAHs in aerosols were identified using diagnostic ratios and principal component analysis. The results reflect a blend of emissions from diesel and natural gas as the major sources of PAH in the city along with contribution from emission of coal, coke, and gasoline.

  17. An objective scatter index based on double-pass retinal images of a point source to classify cataracts.

    Directory of Open Access Journals (Sweden)

    Pablo Artal

    Full Text Available PURPOSE: To propose a new objective scatter index (OSI based in the analysis of double-pass images of a point source to rank and classify cataract patients. This classification scheme is compared with a current subjective system. METHODS: We selected a population including a group of normal young eyes as control and patients diagnosed with cataract (grades NO2, NO3 and NO4 according to the Lens Opacities Classification System (LOCS III. For each eye, we recorded double-pass retinal images of a point source. In each patient, we determined an objective scatter index (OSI as the ratio of the intensity at an eccentric location in the image and the central part. This index provides information on the relevant forward scatter affecting vision. Since the double-pass retinal images are affected by both ocular aberrations and intraocular scattering, an analysis was performed to show the ranges of contributions of aberrations to the OSI. RESULTS: We used the OSI values to classify each eye according to the degree of scatter. The young normal eyes of the control group had OSI values below 1, while the OSI for subjects in LOCS grade II were around 1 to 2. The use of the objective index showed some of the weakness of subjective classification schemes. In particular, several subjects initially classified independently as grade NO2 or NO3 had similar OSI values, and in some cases even higher than subjects classified as grade NO4. A new classification scheme based in OSI is proposed. CONCLUSIONS: We introduced an objective index based in the analysis of double-pass retinal images to classify cataract patients. The method is robust and fully based in objective measurements; i.e., not depending on subjective decisions. This procedure could be used in combination with standard current methods to improve cataract patient surgery scheduling.

  18. Impacts by point and diffuse micropollutant sources on the stream water quality at catchment scale

    Science.gov (United States)

    Petersen, M. F.; Eriksson, E.; Binning, P. J.; Bjerg, P. L.

    2012-04-01

    The water quality of surface waters is threatened by multiple anthropogenic pollutants and the large variety of pollutants challenges the monitoring and assessment of the water quality. The aim of this study was to characterize and quantify both point and diffuse sources of micropollutants impacting the water quality of a stream at catchment scale. Grindsted stream in western Jutland, Denmark was used as a study site. The stream passes both urban and agricultural areas and is impacted by severe groundwater contamination in Grindsted city. Along a 12 km reach of Grindsted stream, the potential pollution sources were identified including a pharmaceutical factory site with a contaminated old drainage ditch, two waste deposits, a wastewater treatment plant, overflow structures, fish farms, industrial discharges and diffuse agricultural and urban sources. Six water samples were collected along the stream and analyzed for general water quality parameters, inorganic constituents, pesticides, sulfonamides, chlorinated solvents, BTEXs, and paracetamol and ibuprofen. The latter two groups were not detected. The general water quality showed typical conditions for a stream in western Jutland. Minor impacts by releases of organic matter and nutrients were found after the fish farms and the waste water treatment plant. Nickel was found at concentrations 5.8 - 8.8 μg/l. Nine pesticides and metabolites of both agricultural and urban use were detected along the stream; among these were the two most frequently detected and some rarely detected pesticides in Danish water courses. The concentrations were generally consistent with other findings in Danish streams and in the range 0.01 - 0.09 μg/l; except for metribuzin-diketo that showed high concentrations up to 0.74 μg/l. The groundwater contamination at the pharmaceutical factory site, the drainage ditch and the waste deposits is similar in composition containing among others sulfonamides and chlorinated solvents (including vinyl

  19. The effects of food sources on Japanese monkey home range size and location, and population dynamics.

    Science.gov (United States)

    Koganezawa, M; Imaki, H

    1999-01-01

    The effects of supplemental feeding by tourists on wild Japanese monkey's home range size and location, and troop size and composition were studied for two monkey troops, Troop A and Troop B, living along the Irohazaka loop road, Nikko National Park, central Japan. Changes were documented based on data gathered from 1982 to 1996 by the use of radio telemetry. Troop A's home range size shrank and changed from separate winter and summer ranges to a single, year-round home range, with its core located in a high elevation area where supplemental feeding by tourists was heavy. Troop B's home range also shrank and shifted to a lower elevation where supplemental feeding by tourists was heavy. Troop A's population size increased between the winters of 1983-1984 and 1990-1991 in conjunction with an increase in human encounter rates, and then decreased. Troop B's size increased until the winter of 1993-1994, and then decreased. The instability of troop size between 1993 and 1996 may be explained by documented factors such as a decrease in the adult sex ratio, an increase in the infant-female ratio, and an increase in juvenile mortality and/or emigration, all of which may have been influenced by supplemental feeding by tourists.

  20. Analytical calculation of the solid angle defined by a cylindrical detector and a point cosine source with parallel axes

    OpenAIRE

    Prata, M. J.

    2003-01-01

    We derive analytical expressions for the solid angle subtended by a right finite circular cylinder at a point source with cosine angular distribution in the case where the source direction is parallel to the cylinder axis. As a subsidiary result, an expression for the solid angle subtended by a disc detector at a spread disc source is also provided, in the case where the two discs have a common symmetry axis which is also coincident with the source direction.

  1. Sources of Caffeine in Diets of US Children and Adults: Trends by Beverage Type and Purchase Location

    OpenAIRE

    Adam Drewnowski; Colin D. Rehm

    2016-01-01

    New sources of caffeine, besides coffee and tea, have been introduced into the US food supply. Data on caffeine consumption age and purchase location can help guide public health policy. National Health and Nutrition Examination Surveys (NHANES) were used to estimate population-level caffeine intakes, using data from 24-h dietary recall. First, caffeine intakes by age-group and beverage type were estimated using the most recent 2011?2012 data (n = 7456). Second, fourteen years trends in caffe...

  2. Risk-based prioritization of ground water threatening point sources at catchment and regional scales

    DEFF Research Database (Denmark)

    Overheu, Niels Døssing; Tuxen, Nina; Flyvbjerg, John

    2014-01-01

    framework has been developed to enable a systematic and transparent risk assessment and prioritization of contaminant point sources, considering the local, catchment, or regional scales (Danish EPA, 2011, 2012). The framework has been tested in several catchments in Denmark with different challenges...... and needs, and two of these are presented. Based on the lessons learned, the Danish EPA has prepared a handbook to guide the user through the steps in a risk-based prioritization (Danish EPA, 2012). It provides guidance on prioritization both in an administratively defined area such as a Danish Region...... of the results are presented using the case studies as examples. The methodology was developed by a broad industry group including the Danish EPA, the Danish Regions, the Danish Nature Agency, the Technical University of Denmark, and consultants — and the framework has been widely accepted by the professional...

  3. Improvement of correlation-based centroiding methods for point source Shack-Hartmann wavefront sensor

    Science.gov (United States)

    Li, Xuxu; Li, Xinyang; wang, Caixia

    2018-03-01

    This paper proposes an efficient approach to decrease the computational costs of correlation-based centroiding methods used for point source Shack-Hartmann wavefront sensors. Four typical similarity functions have been compared, i.e. the absolute difference function (ADF), ADF square (ADF2), square difference function (SDF), and cross-correlation function (CCF) using the Gaussian spot model. By combining them with fast search algorithms, such as three-step search (TSS), two-dimensional logarithmic search (TDL), cross search (CS), and orthogonal search (OS), computational costs can be reduced drastically without affecting the accuracy of centroid detection. Specifically, OS reduces calculation consumption by 90%. A comprehensive simulation indicates that CCF exhibits a better performance than other functions under various light-level conditions. Besides, the effectiveness of fast search algorithms has been verified.

  4. Exposure buildup factors for a cobalt-60 point isotropic source for single and two layer slabs

    International Nuclear Information System (INIS)

    Chakarova, R.

    1992-01-01

    Exposure buildup factors for point isotropic cobalt-60 sources are calculated by the Monte Carlo method with statistical errors ranging from 1.5 to 7% for 1-5 mean free paths (mfp) thick water and iron single slabs and for 1 and 2 mfp iron layers followed by water layers 1-5 mfp thick. The computations take into account Compton scattering. The Monte Carlo data for single slab geometries are approximated by Geometric Progression formula. Kalos's formula using the calculated single slab buildup factors may be applied to reproduce the data for two-layered slabs. The presented results and discussion may help when choosing the manner in which the radiation field gamma irradiation units will be described. (author)

  5. How to mitigate pesticides point sources pollution at the EU level?

    OpenAIRE

    Bonicelli, B.; Laplana, R.; Vaçulik, A.; Maillet-Mezeray, J.; Roetelle, M.; Palagos, B.; Dejean, C.

    2008-01-01

    International audience; Pour réduire les pollutions ponctuelles par les produits de protection des plantes (PPPs) un recueil de Bonnes Pratiques Agricoles (BPAs) a été élaboré dans le cdar du projet Européen TOPPS (Training Operators to prevent Pollution from Point Source). Le bon comportement des opérateurs a été identifié comme le facteur clé pour réduire les risques de pollutions ponctuelles. A l'échelle européenne (A0 pays), une enquête de sensibilité de l'ensemble des décideurs et acteur...

  6. Turbulent gravitational convection from a point source in a non-uniformly stratified environment

    Science.gov (United States)

    Caulfield, C. P.; Woods, Andrew W.

    1998-04-01

    We examine the turbulent gravitational convection which develops above a point source of buoyant fluid in a stably stratified environment in which the buoyancy frequency varies with height according to N2=N2s (z/zs)[beta]. This generalizes the classical model of turbulent buoyant plumes rising through uniform and uniformly stratified environments originally developed by Morton et al. (1956). By analogy, the height of rise of a plume with initial buoyancy flux Fs has the form Hp= Ap[epsilon]p[minus sign]1/2Fs1/4Ns[minus sign]3/4hp ([lambda], [beta]) where [epsilon]p is the entrainment constant for plume motion, Ap is an O(1) constant, and the non-dimensional plume height, hp is a function of &[lambda]=Ap[epsilon]p[minus sign]1/2Fs1/4Ns[minus sign]3/4/zs and [beta].

  7. Preliminary limits on the flux of muon neutrinos from extraterrestrial point sources

    International Nuclear Information System (INIS)

    Bionta, R.M.; Blewitt, G.; Bratton, C.B.

    1985-01-01

    We present the arrival directions of 117 upward-going muon events collected with the IMB proton lifetime detector during 317 days of live detector operation. The rate of upward-going muons observed in our detector was found to be consistent with the rate expected from atmospheric neutrino production. The upper limit on the total flux of extraterrestrial neutrinos >1 GeV is 2 -sec. Using our data and a Monte Carlo simulation of high energy muon production in the earth surrounding the detector, we place limits on the flux of neutrinos from a point source in the Vela X-2 system of 2 -sec with E > 1 GeV. 6 refs., 5 figs

  8. Simulation of agricultural non-point source pollution in Xichuan by using SWAT model

    Science.gov (United States)

    Xing, Linan; Zuo, Jiane; Liu, Fenglin; Zhang, Xiaohui; Cao, Qiguang

    2018-02-01

    This paper evaluated the applicability of using SWAT to access agricultural non-point source pollution in Xichuan area. In order to build the model, DEM, soil sort and land use map, climate monitoring data were collected as basic database. The SWAT model was calibrated and validated for the SWAT was carried out using streamflow, suspended solids, total phosphorus and total nitrogen records from 2009 to 2011. Errors, coefficient of determination and Nash-Sutcliffe coefficient were considered to evaluate the applicability. The coefficient of determination were 0.96, 0.66, 0.55 and 0.66 for streamflow, SS, TN, and TP, respectively. Nash-Sutcliffe coefficient were 0.93, 0.5, 0.52 and 0.63, respectively. The results all meet the requirements. It suggested that the SWAT model can simulate the study area.

  9. Airborne remote sensing and in situ measurements of atmospheric CO2 to quantify point source emissions

    Science.gov (United States)

    Krings, Thomas; Neininger, Bruno; Gerilowski, Konstantin; Krautwurst, Sven; Buchwitz, Michael; Burrows, John P.; Lindemann, Carsten; Ruhtz, Thomas; Schüttemeyer, Dirk; Bovensmann, Heinrich

    2018-02-01

    Reliable techniques to infer greenhouse gas emission rates from localised sources require accurate measurement and inversion approaches. In this study airborne remote sensing observations of CO2 by the MAMAP instrument and airborne in situ measurements are used to infer emission estimates of carbon dioxide released from a cluster of coal-fired power plants. The study area is complex due to sources being located in close proximity and overlapping associated carbon dioxide plumes. For the analysis of in situ data, a mass balance approach is described and applied, whereas for the remote sensing observations an inverse Gaussian plume model is used in addition to a mass balance technique. A comparison between methods shows that results for all methods agree within 10 % or better with uncertainties of 10 to 30 % for cases in which in situ measurements were made for the complete vertical plume extent. The computed emissions for individual power plants are in agreement with results derived from emission factors and energy production data for the time of the overflight.

  10. Field-scale operation of methane biofiltration systems to mitigate point source methane emissions

    International Nuclear Information System (INIS)

    Hettiarachchi, Vijayamala C.; Hettiaratchi, Patrick J.; Mehrotra, Anil K.; Kumar, Sunil

    2011-01-01

    Methane biofiltration (MBF) is a novel low-cost technique for reducing low volume point source emissions of methane (CH 4 ). MBF uses a granular medium, such as soil or compost, to support the growth of methanotrophic bacteria responsible for converting CH 4 to carbon dioxide (CO 2 ) and water (H 2 O). A field research program was undertaken to evaluate the potential to treat low volume point source engineered CH 4 emissions using an MBF at a natural gas monitoring station. A new comprehensive three-dimensional numerical model was developed incorporating advection-diffusive flow of gas, biological reactions and heat and moisture flow. The one-dimensional version of this model was used as a guiding tool for designing and operating the MBF. The long-term monitoring results of the field MBF are also presented. The field MBF operated with no control of precipitation, evaporation, and temperature, provided more than 80% of CH 4 oxidation throughout spring, summer, and fall seasons. The numerical model was able to predict the CH 4 oxidation behavior of the field MBF with high accuracy. The numerical model simulations are presented for estimating CH 4 oxidation efficiencies under various operating conditions, including different filter bed depths and CH 4 flux rates. The field observations as well as numerical model simulations indicated that the long-term performance of MBFs is strongly dependent on environmental factors, such as ambient temperature and precipitation. - Highlights: → One-dimensional version of the model was used as a guiding tool for designing and operating the MBF. → Mathematical model predicted CH 4 oxidation behaviors of the field MBF with high accuracy i.e. (> 80 %). → Performance of MBF is dependent on ambient temperature and precipitation. - The developed numerical model simulations and field observations for estimating CH 4 oxidation efficiencies under various operating conditions indicate that the long-term performance of MBFs is strongly

  11. Carbon dioxide capture and separation techniques for advanced power generation point sources

    Energy Technology Data Exchange (ETDEWEB)

    Pennline, H.W.; Luebke, D.R.; Morsi, B.I.; Heintz, Y.J.; Jones, K.L.; Ilconich, J.B.

    2006-09-01

    The capture/separation step for carbon dioxide (CO2) from large-point sources is a critical one with respect to the technical feasibility and cost of the overall carbon sequestration scenario. For large-point sources, such as those found in power generation, the carbon dioxide capture techniques being investigated by the in-house research area of the National Energy Technology Laboratory possess the potential for improved efficiency and costs as compared to more conventional technologies. The investigated techniques can have wide applications, but the research has focused on capture/separation of carbon dioxide from flue gas (postcombustion from fossil fuel-fired combustors) and from fuel gas (precombustion, such as integrated gasification combined cycle – IGCC). With respect to fuel gas applications, novel concepts are being developed in wet scrubbing with physical absorption; chemical absorption with solid sorbents; and separation by membranes. In one concept, a wet scrubbing technique is being investigated that uses a physical solvent process to remove CO2 from fuel gas of an IGCC system at elevated temperature and pressure. The need to define an ideal solvent has led to the study of the solubility and mass transfer properties of various solvents. Fabrication techniques and mechanistic studies for hybrid membranes separating CO2 from the fuel gas produced by coal gasification are also being performed. Membranes that consist of CO2-philic silanes incorporated into an alumina support or ionic liquids encapsulated into a polymeric substrate have been investigated for permeability and selectivity. An overview of two novel techniques is presented along with a research progress status of each technology.

  12. Carbon Dioxide Capture and Separation Techniques for Gasification-based Power Generation Point Sources

    Energy Technology Data Exchange (ETDEWEB)

    Pennline, H.W.; Luebke, D.R.; Jones, K.L.; Morsi, B.I. (Univ. of Pittsburgh, PA); Heintz, Y.J. (Univ. of Pittsburgh, PA); Ilconich, J.B. (Parsons)

    2007-06-01

    The capture/separation step for carbon dioxide (CO2) from large-point sources is a critical one with respect to the technical feasibility and cost of the overall carbon sequestration scenario. For large-point sources, such as those found in power generation, the carbon dioxide capture techniques being investigated by the in-house research area of the National Energy Technology Laboratory possess the potential for improved efficiency and reduced costs as compared to more conventional technologies. The investigated techniques can have wide applications, but the research has focused on capture/separation of carbon dioxide from flue gas (post-combustion from fossil fuel-fired combustors) and from fuel gas (precombustion, such as integrated gasification combined cycle or IGCC). With respect to fuel gas applications, novel concepts are being developed in wet scrubbing with physical absorption; chemical absorption with solid sorbents; and separation by membranes. In one concept, a wet scrubbing technique is being investigated that uses a physical solvent process to remove CO2 from fuel gas of an IGCC system at elevated temperature and pressure. The need to define an ideal solvent has led to the study of the solubility and mass transfer properties of various solvents. Pertaining to another separation technology, fabrication techniques and mechanistic studies for membranes separating CO2 from the fuel gas produced by coal gasification are also being performed. Membranes that consist of CO2-philic ionic liquids encapsulated into a polymeric substrate have been investigated for permeability and selectivity. Finally, dry, regenerable processes based on sorbents are additional techniques for CO2 capture from fuel gas. An overview of these novel techniques is presented along with a research progress status of technologies related to membranes and physical solvents.

  13. Guided wave mode dispersion of transient acoustic emission on copper pipes-Its visualisation and application to source location

    Science.gov (United States)

    Wang, Chao; Joe Au, Y. H.; Li, Lin; Cheng, Kai

    2016-03-01

    In this paper is presented an improved method for locating a transient acoustic emission (AE) source on a pipeline with two broad-band AE sensors. Using Short Time Fourier Transform (STFT), the method identifies a flexural wave mode, F(1,1), in the two AE signals detected, notes its respective arrival times at different frequencies, and determines the location of the AE source based on the arrival times. Due to velocity dispersion, the arrival time of the wave mode varies with frequency. The method has three main advantages: that the wave speed is not required in the calculation, that it is insensitive to threshold setting for arrival time estimation, and that, at least in theory, the accuracy of the source location can be made as high as desired. The paper first demonstrates, by way of an experiment, the inadequacy of threshold-crossing as a method for identifying the first arrival time of the AE wave. The paper then presents the theory of the proposed method and of the estimated error inherent in the theory and an explanation on how the error can be reduced. The method is then verified experimentally using results obtained from a 3-m long copper pipe of 22 mm diameter.

  14. Application of the complex cepstrum to the location of acoustic sources near reflective surfaces

    Science.gov (United States)

    Fuller, C. R.; Tavakkoli, S.; Elliott, K. B.; Hurst, C. J.; Obrien, W. F.

    1987-01-01

    The complex cepstrum is used to correct bearing estimations of acoustic sources in the presence of a reflective surface. An automated liftering procedure is used which zeros out a block portion of the cepstrum including the echo information. The problem of the resulting distortion is alleviated by applying a coherence criterion to the recovered direct signals at each microphone. Thus to a large degree the interactive nature of cepstral processing is overcome for this application. For the test signals and geometries considered the cepstrum is shown to accurately correct for bearing errors in acoustic signals contaminated with reflections from nearby surfaces.

  15. Metamaterials-based sensor to detect and locate nonlinear elastic sources

    International Nuclear Information System (INIS)

    Gliozzi, Antonio S.; Scalerandi, Marco; Miniaci, Marco; Bosia, Federico; Pugno, Nicola M.

    2015-01-01

    In recent years, acoustic metamaterials have attracted increasing scientific interest for very diverse technological applications ranging from sound abatement to ultrasonic imaging, mainly due to their ability to act as band-stop filters. At the same time, the concept of chaotic cavities has been recently proposed as an efficient tool to enhance the quality of nonlinear signal analysis, particularly in the ultrasonic/acoustic case. The goal of the present paper is to merge the two concepts in order to propose a metamaterial-based device that can be used as a natural and selective linear filter for the detection of signals resulting from the propagation of elastic waves in nonlinear materials, e.g., in the presence of damage, and as a detector for the damage itself in time reversal experiments. Numerical simulations demonstrate the feasibility of the approach and the potential of the device in providing improved signal-to-noise ratios and enhanced focusing on the defect locations

  16. Waveform inversion of lateral velocity variation from wavefield source location perturbation

    KAUST Repository

    Choi, Yun Seok

    2013-09-22

    It is challenge in waveform inversion to precisely define the deep part of the velocity model compared to the shallow part. The lateral velocity variation, or what referred to as the derivative of velocity with respect to the horizontal distance, with well log data can be used to update the deep part of the velocity model more precisely. We develop a waveform inversion algorithm to obtain the lateral velocity variation by inverting the wavefield variation associated with the lateral shot location perturbation. The gradient of the new waveform inversion algorithm is obtained by the adjoint-state method. Our inversion algorithm focuses on resolving the lateral changes of the velocity model with respect to a fixed reference vertical velocity profile given by a well log. We apply the method on a simple-dome model to highlight the methods potential.

  17. Metamaterials-based sensor to detect and locate nonlinear elastic sources

    Energy Technology Data Exchange (ETDEWEB)

    Gliozzi, Antonio S.; Scalerandi, Marco [Department of Applied Science and Technology, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy); Miniaci, Marco; Bosia, Federico [Department of Physics, University of Torino, Via Pietro Giuria 1, 10125 Torino (Italy); Pugno, Nicola M. [Laboratory of Bio-Inspired and Graphene Nanomechanics, Department of Civil, Environmental and Mechanical Engineering, University of Trento, Via Mesiano 77, 38123 Trento (Italy); Center for Materials and Microsystems, Fondazione Bruno Kessler, Via Sommarive 18, 38123 Povo (Trento) (Italy); School of Engineering and Materials Science, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom)

    2015-10-19

    In recent years, acoustic metamaterials have attracted increasing scientific interest for very diverse technological applications ranging from sound abatement to ultrasonic imaging, mainly due to their ability to act as band-stop filters. At the same time, the concept of chaotic cavities has been recently proposed as an efficient tool to enhance the quality of nonlinear signal analysis, particularly in the ultrasonic/acoustic case. The goal of the present paper is to merge the two concepts in order to propose a metamaterial-based device that can be used as a natural and selective linear filter for the detection of signals resulting from the propagation of elastic waves in nonlinear materials, e.g., in the presence of damage, and as a detector for the damage itself in time reversal experiments. Numerical simulations demonstrate the feasibility of the approach and the potential of the device in providing improved signal-to-noise ratios and enhanced focusing on the defect locations.

  18. Application of random-point processes to the detection of radiation sources

    International Nuclear Information System (INIS)

    Woods, J.W.

    1978-01-01

    In this report the mathematical theory of random-point processes is reviewed and it is shown how use of the theory can obtain optimal solutions to the problem of detecting radiation sources. As noted, the theory also applies to image processing in low-light-level or low-count-rate situations. Paralleling Snyder's work, the theory is extended to the multichannel case of a continuous, two-dimensional (2-D), energy-time space. This extension essentially involves showing that the data are doubly stochastic Poisson (DSP) point processes in energy as well as time. Further, a new 2-D recursive formulation is presented for the radiation-detection problem with large computational savings over nonrecursive techniques when the number of channels is large (greater than or equal to 30). Finally, some adaptive strategies for on-line ''learning'' of unknown, time-varying signal and background-intensity parameters and statistics are present and discussed. These adaptive procedures apply when a complete statistical description is not available a priori

  19. The energy sources and nuclear energy - The point of view of the Belgian Catholic Church

    International Nuclear Information System (INIS)

    Hoenraet, Christian

    2000-01-01

    The problems related to the environment are reported regularly to the public by means of the newspapers, on radio and television. The story is the product of a journalistic process and in general does not bear much resemblance to the original event. The rate and type of reportage depend not only on the body of data available to the journalist but on the information sources the journalist chosen to use. The same story is reported in a positive or negative way. Finally people are overwhelmed by contradictory information and became uncertain or frightened. In order to provide the general public with objective information about nuclear energy in particular and to made a statement about the position of the Belgian Catholic Church concerning this matter, the results of the study were published in Dutch under the form of a book with the title 'The Energy Sources and Nuclear Energy - Comparative analysis and ethical thoughts written the same author. Thia paper is a short survey of the results of the study and to present the point of view of the Belgian Catholic Church in the energy debate

  20. Point-source and diffuse high-energy neutrino emission from Type IIn supernovae

    Science.gov (United States)

    Petropoulou, M.; Coenders, S.; Vasilopoulos, G.; Kamble, A.; Sironi, L.

    2017-09-01

    Type IIn supernovae (SNe), a rare subclass of core collapse SNe, explode in dense circumstellar media that have been modified by the SNe progenitors at their last evolutionary stages. The interaction of the freely expanding SN ejecta with the circumstellar medium gives rise to a shock wave propagating in the dense SN environment, which may accelerate protons to multi-PeV energies. Inelastic proton-proton collisions between the shock-accelerated protons and those of the circumstellar medium lead to multimessenger signatures. Here, we evaluate the possible neutrino signal of Type IIn SNe and compare with IceCube observations. We employ a Monte Carlo method for the calculation of the diffuse neutrino emission from the SN IIn class to account for the spread in their properties. The cumulative neutrino emission is found to be ˜10 per cent of the observed IceCube neutrino flux above 60 TeV. Type IIn SNe would be the dominant component of the diffuse astrophysical flux, only if 4 per cent of all core collapse SNe were of this type and 20-30 per cent of the shock energy was channeled to accelerated protons. Lower values of the acceleration efficiency are accessible by the observation of a single Type IIn SN as a neutrino point source with IceCube using up-going muon neutrinos. Such an identification is possible in the first year following the SN shock breakout for sources within 20 Mpc.

  1. Strategic management of non-point source pollution from sewage sludge.

    Science.gov (United States)

    Burke, S; Heathwaite, L; Quinn, P; Merrett, S; Whitehead, P; Preedy, N; Lerner, D; Saul, A

    2003-01-01

    In the UK, the recycling of sewage sludge to land is expected to double by 2006 but the security of this route is threatened by environmental concerns and health scares. Strategic investment is needed to ensure sustainable and secure sludge recycling outlets. At present, the security of this landbank for sludge recycling is determined by legislation relating to nutrient rather than potentially toxic elements (PTEs) applications to land--especially the environmental risk linked to soil phosphorus (P) saturation. We believe that not all land has an equal risk of contributing nutrients derived from applications to land to receiving waters. We are currently investigating whether it is possible to minimise nutrient loss by applying sludge to land outside Critical Source Areas (CSAs) regardless of soil P Index status. Research is underway to develop a predictive and spatially-sensitive, semi-distributed model of critical thresholds for sludge application that goes beyond traditional "end-of-pipe" or "edge-of-field" modelling, to include hydrological flow paths and delivery mechanisms to receiving waters from non-point sources at the catchment scale.

  2. Deconstructing a galaxy: colour distributions of point sources in Messier 83

    Science.gov (United States)

    Kiar, A. K.; Barmby, P.; Hidalgo, A.

    2017-11-01

    What do we see when we look at a nearby, well-resolved galaxy? Thousands of individual sources are detected in multiband imaging observations of even a fraction of a nearby galaxy, and characterizing those sources is a complex process. This work analyses a ten-band photometric catalogue of nearly 70 000 point sources in a 7.3 square arcmin region of the nearby spiral galaxy Messier 83, made as part of the Early Release Science programme with the Hubble Space Telescope's Wide Field Camera 3. Colour distributions were measured for both broad-band and broad-and-narrow-band colours; colours made from broad-bands with large wavelength differences generally had broader distributions although B - V was an exception. Two- and three-dimensional colour spaces were generated using various combinations of four bands and clustered with the K-Means and Mean Shift algorithms. Neither algorithm was able to consistently segment the colour distributions: while some distinct features in colour space were apparent in visual examinations, these features were not compact or isolated enough to be recognized as clusters in colour space. K-Means clustering of the UBVI colour space was able to identify a group of objects more likely to be star clusters. Mean Shift was successful in identifying outlying groups at the edges of colour distributions. For identifying objects whose emission is dominated by spectral lines, there was no clear benefit from combining narrow-band photometry in multiple bands compared to a simple continuum subtraction. The clustering analysis results are used to inform recommendations for future surveys of nearby galaxies.

  3. A land use regression model incorporating data on industrial point source pollution.

    Science.gov (United States)

    Chen, Li; Wang, Yuming; Li, Peiwu; Ji, Yaqin; Kong, Shaofei; Li, Zhiyong; Bai, Zhipeng

    2012-01-01

    Advancing the understanding of the spatial aspects of air pollution in the city regional environment is an area where improved methods can be of great benefit to exposure assessment and policy support. We created land use regression (LUR) models for SO2, NO2 and PM10 for Tianjin, China. Traffic volumes, road networks, land use data, population density, meteorological conditions, physical conditions and satellite-derived greenness, brightness and wetness were used for predicting SO2, NO2 and PM10 concentrations. We incorporated data on industrial point sources to improve LUR model performance. In order to consider the impact of different sources, we calculated the PSIndex, LSIndex and area of different land use types (agricultural land, industrial land, commercial land, residential land, green space and water area) within different buffer radii (1 to 20 km). This method makes up for the lack of consideration of source impact based on the LUR model. Remote sensing-derived variables were significantly correlated with gaseous pollutant concentrations such as SO2 and NO2. R2 values of the multiple linear regression equations for SO2, NO2 and PM10 were 0.78, 0.89 and 0.84, respectively, and the RMSE values were 0.32, 0.18 and 0.21, respectively. Model predictions at validation monitoring sites went well with predictions generally within 15% of measured values. Compared to the relationship between dependent variables and simple variables (such as traffic variables or meteorological condition variables), the relationship between dependent variables and integrated variables was more consistent with a linear relationship. Such integration has a discernable influence on both the overall model prediction and health effects assessment on the spatial distribution of air pollution in the city region.

  4. Using sorbent waste materials to enhance treatment of micro-point source effluents by constructed wetlands

    Science.gov (United States)

    Green, Verity; Surridge, Ben; Quinton, John; Matthews, Mike

    2014-05-01

    Sorbent materials are widely used in environmental settings as a means of enhancing pollution remediation. A key area of environmental concern is that of water pollution, including the need to treat micro-point sources of wastewater pollution, such as from caravan sites or visitor centres. Constructed wetlands (CWs) represent one means for effective treatment of wastewater from small wastewater producers, in part because they are believed to be economically viable and environmentally sustainable. Constructed wetlands have the potential to remove a range of pollutants found in wastewater, including nitrogen (N), phosphorus (P), biochemical oxygen demand (BOD) and carbon (C), whilst also reducing the total suspended solids (TSS) concentration in effluents. However, there remain particular challenges for P and N removal from wastewater in CWs, as well as the sometimes limited BOD removal within these treatment systems, particularly for micro-point sources of wastewater. It has been hypothesised that the amendment of CWs with sorbent materials can enhance their potential to treat wastewater, particularly through enhancing the removal of N and P. This paper focuses on data from batch and mesocosm studies that were conducted to identify and assess sorbent materials suitable for use within CWs. The aim in using sorbent material was to enhance the combined removal of phosphate (PO4-P) and ammonium (NH4-N). The key selection criteria for the sorbent materials were that they possess effective PO4-P, NH4-N or combined pollutant removal, come from low cost and sustainable sources, have potential for reuse, for example as a fertiliser or soil conditioner, and show limited potential for re-release of adsorbed nutrients. The sorbent materials selected for testing were alum sludge from water treatment works, ochre derived from minewater treatment, biochar derived from various feedstocks, plasterboard and zeolite. The performance of the individual sorbents was assessed through

  5. A Heuristic Algorithm for Constrained Multi-Source Location Problem with Closest Distance under Gauge: The Variational Inequality Approach

    Directory of Open Access Journals (Sweden)

    Jian-Lin Jiang

    2013-01-01

    Full Text Available This paper considers the locations of multiple facilities in the space , with the aim of minimizing the sum of weighted distances between facilities and regional customers, where the proximity between a facility and a regional customer is evaluated by the closest distance. Due to the fact that facilities are usually allowed to be sited in certain restricted areas, some locational constraints are imposed to the facilities of our problem. In addition, since the symmetry of distances is sometimes violated in practical situations, the gauge is employed in this paper instead of the frequently used norms for measuring both the symmetric and asymmetric distances. In the spirit of the Cooper algorithm (Cooper, 1964, a new location-allocation heuristic algorithm is proposed to solve this problem. In the location phase, the single-source subproblem with regional demands is reformulated into an equivalent linear variational inequality (LVI, and then, a projection-contraction (PC method is adopted to find the optimal locations of facilities, whereas in the allocation phase, the regional customers are allocated to facilities according to the nearest center reclassification (NCR. The convergence of the proposed algorithm is proved under mild assumptions. Some preliminary numerical results are reported to show the effectiveness of the new algorithm.

  6. The network simulation method: a useful tool for locating the kinetic-thermodynamic switching point in complex kinetic schemes.

    Science.gov (United States)

    Caravaca, Manuel; Sanchez-Andrada, Pilar; Soto, Antonio; Alajarin, Mateo

    2014-12-14

    The kinetic-thermodynamic switching point of a multistep process, whose reaction mechanism has been elucidated by DFT calculations, can be calculated by means of an efficient model based on the Network Simulation Method (NSM). This method can solve, fast and effectively, a difficult system of differential equations derived from a complex kinetic scheme by establishing a formal equivalence between the chemical system and an electrical network. The NSM employs very short simulation times to determine the dependence of the switching time on the temperature, a fundamental topic to take control over the product composition which has not been treated exhaustively so far, and that could be applied for synthetic purposes avoiding laborious and costly experimental trials.

  7. The recovery of a time-dependent point source in a linear transport equation: application to surface water pollution

    International Nuclear Information System (INIS)

    Hamdi, Adel

    2009-01-01

    The aim of this paper is to localize the position of a point source and recover the history of its time-dependent intensity function that is both unknown and constitutes the right-hand side of a 1D linear transport equation. Assuming that the source intensity function vanishes before reaching the final control time, we prove that recording the state with respect to the time at two observation points framing the source region leads to the identification of the source position and the recovery of its intensity function in a unique manner. Note that at least one of the two observation points should be strategic. We establish an identification method that determines quasi-explicitly the source position and transforms the task of recovering its intensity function into solving directly a well-conditioned linear system. Some numerical experiments done on a variant of the water pollution BOD model are presented

  8. 18O isotopic characterisation of non-point source contributed heavy metals (Zn and Cu) contamination of groundwater

    International Nuclear Information System (INIS)

    Datta, P.S.; Manjaiah, K.M.; Tyagi, S.K.

    1999-01-01

    In many urbanised areas, fast depletion and severe degradation of the of groundwater resource with contaminants such as nitrate, fluoride, and heavy metals is a common phenomenon, resulting in zonal disparity in fresh water availability. Therefore, for protection of groundwater from pollution and depletion, it is a matter of concern for the planners and decision makers to clearly characterise the sources of contamination and to search for an alternative approach for groundwater development and management. In this context, a new approach is presented here, based on monitoring of 18 O stable isotopic and heavy metals composition of groundwater, to clearly characterise non-point source contributed heavy metals pollution of groundwater in northern parts of Delhi area. In the investigated area, the Cu content in the groundwater ranges from 3-41 μg/l and Zn content ranges from 5-182 μg/l, showing considerable variation from location to location as well as within the small parts of a location. Wide variation in the 18 O stable isotope content of groundwater (δ value of -5.7 per mille to -8.5 per mille) is due to significant variation in the δ 18 O-contents of rainfall with space and time, as well as intensity and distribution of rainfall. Enrichment in 18 O composition with increasing Cu and Zn levels in groundwater suggest that infiltration of rain water, irrigation water and surface run-off water from the surrounding farm lands, along with agrochemicals and other salts present in the soil, to be the main processes causing groundwater contamination. The concentration of Cu and Zn in groundwater vary spatially, due to different degrees of evaporation/recharge, amounts of fertiliser applied and wastes disposed, adsorption/dispersion of species in the soils and lateral mixing of groundwater. Two opposite mechanisms adsorption and redistribution of infiltrating water along with Zn and Cu species in the soil zone are likely to affect the movement of the Zn and Cu species

  9. Seismic swarm associated with the 2008 eruption of Kasatochi Volcano, Alaska: earthquake locations and source parameters

    Science.gov (United States)

    Ruppert, Natalia G.; Prejean, Stephanie G.; Hansen, Roger A.

    2011-01-01

    An energetic seismic swarm accompanied an eruption of Kasatochi Volcano in the central Aleutian volcanic arc in August of 2008. In retrospect, the first earthquakes in the swarm were detected about 1 month prior to the eruption onset. Activity in the swarm quickly intensified less than 48 h prior to the first large explosion and subsequently subsided with decline of eruptive activity. The largest earthquake measured as moment magnitude 5.8, and a dozen additional earthquakes were larger than magnitude 4. The swarm exhibited both tectonic and volcanic characteristics. Its shear failure earthquake features were b value = 0.9, most earthquakes with impulsive P and S arrivals and higher-frequency content, and earthquake faulting parameters consistent with regional tectonic stresses. Its volcanic or fluid-influenced seismicity features were volcanic tremor, large CLVD components in moment tensor solutions, and increasing magnitudes with time. Earthquake location tests suggest that the earthquakes occurred in a distributed volume elongated in the NS direction either directly under the volcano or within 5-10 km south of it. Following the MW 5.8 event, earthquakes occurred in a new crustal volume slightly east and north of the previous earthquakes. The central Aleutian Arc is a tectonically active region with seismicity occurring in the crusts of the Pacific and North American plates in addition to interplate events. We postulate that the Kasatochi seismic swarm was a manifestation of the complex interaction of tectonic and magmatic processes in the Earth's crust. Although magmatic intrusion triggered the earthquakes in the swarm, the earthquakes failed in context of the regional stress field.

  10. Characterizing and locating air pollution sources in a complex industrial district using optical remote sensing technology and multivariate statistical modeling.

    Science.gov (United States)

    Chang, Pao-Erh Paul; Yang, Jen-Chih Rena; Den, Walter; Wu, Chang-Fu

    2014-09-01

    Emissions of volatile organic compounds (VOCs) are most frequent environmental nuisance complaints in urban areas, especially where industrial districts are nearby. Unfortunately, identifying the responsible emission sources of VOCs is essentially a difficult task. In this study, we proposed a dynamic approach to gradually confine the location of potential VOC emission sources in an industrial complex, by combining multi-path open-path Fourier transform infrared spectrometry (OP-FTIR) measurement and the statistical method of principal component analysis (PCA). Close-cell FTIR was further used to verify the VOC emission source by measuring emitted VOCs from selected exhaust stacks at factories in the confined areas. Multiple open-path monitoring lines were deployed during a 3-month monitoring campaign in a complex industrial district. The emission patterns were identified and locations of emissions were confined by the wind data collected simultaneously. N,N-Dimethyl formamide (DMF), 2-butanone, toluene, and ethyl acetate with mean concentrations of 80.0 ± 1.8, 34.5 ± 0.8, 103.7 ± 2.8, and 26.6 ± 0.7 ppbv, respectively, were identified as the major VOC mixture at all times of the day around the receptor site. As the toxic air pollutant, the concentrations of DMF in air samples were found exceeding the ambient standard despite the path-average effect of OP-FTIR upon concentration levels. The PCA data identified three major emission sources, including PU coating, chemical packaging, and lithographic printing industries. Applying instrumental measurement and statistical modeling, this study has established a systematic approach for locating emission sources. Statistical modeling (PCA) plays an important role in reducing dimensionality of a large measured dataset and identifying underlying emission sources. Instrumental measurement, however, helps verify the outcomes of the statistical modeling. The field study has demonstrated the feasibility of

  11. Using a hybrid of traditional 3D FE model, Artificial Neural Networks (ANN), and Genetic Algorithms (GA), to help locating DNAPL sources in a contaminated site

    Science.gov (United States)

    Orr, S.; Boger, Z.

    2008-12-01

    After many years of unsuccessful pump and treat in a contaminated site in Washington, it has become clear that the actual locations of Carbon Tetrachloride (CTC) sources, particularly their interception points at the water table, were unknown. In fact, the actual sources at the surface were partly known, particularly where the history of dumping and leaking from several facilities was known. However, due to a 200-feet thick and complex vadose zone, conducive to lateral migration, this knowledge was practically misleading at the high- resolution required by the pump-treat-inject operation. A quick, data-driven Artificial Neural network (ANN) was used to imitate FEFLOW (a 3D finite-element code), in two ways: (a) by direct inverse; and (b) by indirect inverse modeling (which includes forward simulations). Since the ANN is many folds faster than FEFLOW, it could generate millions of scenarios, and then use genetic algorithms (GA) to efficiently search for the combination of sources that minimizes the errors between simulated and measured concentrations in all wells, over time. While results from the direct inverse were not consistent with simulated concentration profiles in the 31 wells, results from the more robust indirect inverse were much closer to the real concentration trends in all wells, as verified by a FEFLOW simulation using the sources determined by indirect inverse.

  12. User's Guide for the Agricultural Non-Point Source (AGNPS) Pollution Model Data Generator

    Science.gov (United States)

    Finn, Michael P.; Scheidt, Douglas J.; Jaromack, Gregory M.

    2003-01-01

    BACKGROUND Throughout this user guide, we refer to datasets that we used in conjunction with developing of this software for supporting cartographic research and producing the datasets to conduct research. However, this software can be used with these datasets or with more 'generic' versions of data of the appropriate type. For example, throughout the guide, we refer to national land cover data (NLCD) and digital elevation model (DEM) data from the U.S. Geological Survey (USGS) at a 30-m resolution, but any digital terrain model or land cover data at any appropriate resolution will produce results. Another key point to keep in mind is to use a consistent data resolution for all the datasets per model run. The U.S. Department of Agriculture (USDA) developed the Agricultural Nonpoint Source (AGNPS) pollution model of watershed hydrology in response to the complex problem of managing nonpoint sources of pollution. AGNPS simulates the behavior of runoff, sediment, and nutrient transport from watersheds that have agriculture as their prime use. The model operates on a cell basis and is a distributed parameter, event-based model. The model requires 22 input parameters. Output parameters are grouped primarily by hydrology, sediment, and chemical output (Young and others, 1995.) Elevation, land cover, and soil are the base data from which to extract the 22 input parameters required by the AGNPS. For automatic parameter extraction, follow the general process described in this guide of extraction from the geospatial data through the AGNPS Data Generator to generate input parameters required by the pollution model (Finn and others, 2002.)

  13. Morphology, chemistry and distribution of neoformed spherulites in agricultural land affected by metallurgical point-source pollution.

    Science.gov (United States)

    Leguédois, Sophie; Van Oort, Folkert; Jongmans, Toine; Chevallier, Pierre

    2004-07-01

    Metal distribution patterns in superficial soil horizons of agricultural land affected by metallurgical point-source pollution were studied using optical and electron microscopy, synchrotron radiation and spectroscopy analyses. The site is located in northern France, at the center of a former entry lane to a bunker of World War II, temporarily paved with coarse industrial waste fragments and removed at the end of the war. Thin sections made from undisturbed soil samples from A and B horizons were studied. Optical microscopy revealed the occurrence of yellow micrometer-sized (Ap horizon) and red decamicrometer-sized spherulites (AB, B(1)g horizons) as well as distinct distribution patterns. The chemical composition of the spherulites was dominated by Fe, Mn, Zn, Pb, Ca, and P. Comparison of calculated Zn stocks, both in the groundmass and in spherulites, showed a quasi-exclusive Zn accumulation in these neoformed features. Their formation was related to several factors: (i) liberation of metal elements due to weathering of waste products, (ii) Ca and P supply from fertilizing practices, (iii) co-precipitation of metal elements and Ca and P in a porous soil environment, after slow exudation of a supersaturated soil solution in more confined mineral media.

  14. A Numerical Study on the Excitation of Guided Waves in Rectangular Plates Using Multiple Point Sources

    Directory of Open Access Journals (Sweden)

    Wenbo Duan

    2017-12-01

    Full Text Available Ultrasonic guided waves are widely used to inspect and monitor the structural integrity of plates and plate-like structures, such as ship hulls and large storage-tank floors. Recently, ultrasonic guided waves have also been used to remove ice and fouling from ship hulls, wind-turbine blades and aeroplane wings. In these applications, the strength of the sound source must be high for scanning a large area, or to break the bond between ice, fouling and plate substrate. More than one transducer may be used to achieve maximum sound power output. However, multiple sources can interact with each other, and form a sound field in the structure with local constructive and destructive regions. Destructive regions are weak regions and shall be avoided. When multiple transducers are used it is important that they are arranged in a particular way so that the desired wave modes can be excited to cover the whole structure. The objective of this paper is to provide a theoretical basis for generating particular wave mode patterns in finite-width rectangular plates whose length is assumed to be infinitely long with respect to its width and thickness. The wave modes have displacements in both width and thickness directions, and are thus different from the classical Lamb-type wave modes. A two-dimensional semi-analytical finite element (SAFE method was used to study dispersion characteristics and mode shapes in the plate up to ultrasonic frequencies. The modal analysis provided information on the generation of modes suitable for a particular application. The number of point sources and direction of loading for the excitation of a few representative modes was investigated. Based on the SAFE analysis, a standard finite element modelling package, Abaqus, was used to excite the designed modes in a three-dimensional plate. The generated wave patterns in Abaqus were then compared with mode shapes predicted in the SAFE model. Good agreement was observed between the

  15. Agricultural non-point source pollution in China: causes and mitigation measures.

    Science.gov (United States)

    Sun, Bo; Zhang, Linxiu; Yang, Linzhang; Zhang, Fusuo; Norse, David; Zhu, Zhaoliang

    2012-06-01

    Non-point source (NPS) pollution has been increasingly serious in China since the 1990s. The increases of agricultural NPS pollution in China is evaluated for the period 2000-2008 by surveying the literature on water and soil pollution from fertilizers and pesticides, and assessing the surplus nitrogen balance within provinces. The main causes for NPS pollution were excessive inputs of nitrogen fertilizer and pesticides, which were partly the result of the inadequate agricultural extension services and the rapid expansion of intensive livestock production with little of waste management. The annual application of synthetic nitrogen fertilizers and pesticides in China increased by 50.7 and 119.7%, respectively, during 1991-2008. The mitigation measures to reduce NPS pollution include: correct distortion in fertilizer prices; improve incentives for the recycling of organic manure; provide farmers with better information on the sound use of agro-chemicals; and tighten the regulations and national standards on organic waste disposal and pesticides use.

  16. Economic-environmental modeling of point source pollution in Jefferson County, Alabama, USA.

    Science.gov (United States)

    Kebede, Ellene; Schreiner, Dean F; Huluka, Gobena

    2002-05-01

    This paper uses an integrated economic-environmental model to assess the point source pollution from major industries in Jefferson County, Northern Alabama. Industrial expansion generates employment, income, and tax revenue for the public sector; however, it is also often associated with the discharge of chemical pollutants. Jefferson County is one of the largest industrial counties in Alabama that experienced smog warnings and ambient ozone concentration, 1996-1999. Past studies of chemical discharge from industries have used models to assess the pollution impact of individual plants. This study, however, uses an extended Input-Output (I-O) economic model with pollution emission coefficients to assess direct and indirect pollutant emission for several major industries in Jefferson County. The major findings of the study are: (a) the principal emission by the selected industries are volatile organic compounds (VOC) and these contribute to the ambient ozone concentration; (b) the direct and indirect emissions are significantly higher than the direct emission by some industries, indicating that an isolated analysis will underestimate the emission by an industry; (c) while low emission coefficient industries may suggest industry choice they may also emit the most hazardous chemicals. This study is limited by the assumptions made, and the data availability, however it provides a useful analytical tool for direct and cumulative emission estimation and generates insights on the complexity in choice of industries.

  17. Science, information, technology, and the changing character of public policy in non-point source pollution

    Science.gov (United States)

    King, John L.; Corwin, Dennis L.

    Information technologies are already delivering important new capabilities for scientists working on non-point source (NPS) pollution in the vadose zone, and more are expected. This paper focuses on the special contributions of modeling and network communications for enhancing the effectiveness of scientists in the realm of policy debates regarding NPS pollution mitigation and abatement. The discussion examines a fundamental shift from a strict regulatory strategy of pollution control characterized by a bureaucratic/technical alliance during the period through the 1970's and early 1980's, to a more recently evolving paradigm of pluralistic environmental management. The role of science and scientists in this shift is explored, with special attention to the challenges facing scientists working in NPS pollution in the vadose zone. These scientists labor under a special handicap in the evolving model because their scientific tools are often times incapable of linking NPS pollution with individuals responsible for causing it. Information can facilitate the effectiveness of these scientists in policy debates, but not under the usual assumptions in which scientific truth prevails. Instead, information technology's key role is in helping scientists shape the evolving discussion of trade-offs and in bringing citizens and policymakers closer to the routine work of scientists.

  18. Rotating 2d point source plume models with application to Deepwater Horizon

    Science.gov (United States)

    Fabregat, A.; Deremble, B.; Wienders, N.; Stroman, A.; Poje, A.; Özgökmen, T. M.; Dewar, W. K.

    2017-11-01

    The 2010 Deepwater Horizon (DwH) accident in the Gulf of Mexico has renewed oceanographic interest in point source buoyant convection. The present paper applies modern numerical techniques to study this problem, focussing specifically on the DwH event. The gas/oil/seawater nature of the problem requires a 'multiphase' approach, which is relatively unfamiliar in physical oceanography, although applications are becoming more common. The model is cast in an Eulerian framework and includes feedbacks between the convection and the environment, unlike past oil/gas plume simulations that adopt a semi-passive, Lagrangian approach. Fully three dimensional (3d) simulations are too computationally demanding for practical multi-day use, so a two-dimensional (2d) radially symmetric model is developed from the equations and calibrated to the 3d results. Both the 2d and 3d solutions show the somewhat unexpected result that oil/bubble plumes modelled after the DwH event are strongly affected by rotation and exert a considerable dynamic feedback on the ambient. These effects are not typically included in classical oil/gas plume models.

  19. Mycotoxins: diffuse and point source contributions of natural contaminants of emerging concern to streams.

    Science.gov (United States)

    Kolpin, Dana W; Schenzel, Judith; Meyer, Michael T; Phillips, Patrick J; Hubbard, Laura E; Scott, Tia-Marie; Bucheli, Thomas D

    2014-02-01

    To determine the prevalence of mycotoxins in streams, 116 water samples from 32 streams and three wastewater treatment plant effluents were collected in 2010 providing the broadest investigation on the spatial and temporal occurrence of mycotoxins in streams conducted in the United States to date. Out of the 33 target mycotoxins measured, nine were detected at least once during this study. The detections of mycotoxins were nearly ubiquitous during this study even though the basin size spanned four orders of magnitude. At least one mycotoxin was detected in 94% of the 116 samples collected. Deoxynivalenol was the most frequently detected mycotoxin (77%), followed by nivalenol (59%), beauvericin (43%), zearalenone (26%), β-zearalenol (20%), 3-acetyl-deoxynivalenol (16%), α-zearalenol (10%), diacetoxyscirpenol (5%), and verrucarin A (1%). In addition, one or more of the three known estrogenic compounds (i.e. zearalenone, α-zearalenol, and β-zearalenol) were detected in 43% of the samples, with maximum concentrations substantially higher than observed in previous research. While concentrations were generally low (i.e. applications from exposed livestock) and point (e.g. wastewater treatment plants and food processing plants) sources are important environmental pathways for mycotoxin transport to streams. The ecotoxicological impacts from the long-term, low-level exposures to mycotoxins alone or in combination with complex chemical mixtures are unknown. © 2013.

  20. Numerical simulation of electromagnetic acoustic transducers using distributed point source method.

    Science.gov (United States)

    Eskandarzade, M; Kundu, T; Liebeaux, N; Placko, D; Mobadersani, F

    2010-05-01

    In spite of many advances in analytical and numerical modeling techniques for solving different engineering problems, an efficient solution technique for wave propagation modeling of an electromagnetic acoustic transducer (EMAT) system is still missing. Distributed point source method (DPSM) is a newly developed semi-analytical technique developed since 2000 by Placko and Kundu (2007) [12] that is very powerful and straightforward for solving various engineering problems, including acoustic and electromagnetic modeling problems. In this study DPSM has been employed to model the Lorentz type EMAT with a meander line and flat spiral type coil. The problem of wave propagation has been solved and eddy currents and Lorentz forces have been calculated. The displacement field has been obtained as well. While modeling the Lorentz force the effect of dynamic magnetic field has been considered that most current analyses ignore. Results from this analysis have been compared with the finite element method (FEM) based predictions. It should be noted that with the current state of knowledge this problem can be solved only by FEM. Copyright 2009 Elsevier B.V. All rights reserved.

  1. Parameter uncertainty analysis of non-point source pollution from different land use types.

    Science.gov (United States)

    Shen, Zhen-yao; Hong, Qian; Yu, Hong; Niu, Jun-feng

    2010-03-15

    Land use type is one of the most important factors that affect the uncertainty in non-point source (NPS) pollution simulation. In this study, seventeen sensitive parameters were screened from the Soil and Water Assessment Tool (SWAT) model for parameter uncertainty analysis for different land use types in the Daning River Watershed of the Three Gorges Reservoir area, China. First-Order Error Analysis (FOEA) method was adopted to analyze the effect of parameter uncertainty on model outputs under three types of land use, namely, plantation, forest and grassland. The model outputs selected in this study consisted of runoff, sediment yield, organic nitrogen (N), and total phosphorus (TP). The results indicated that the uncertainty conferred by the parameters differed among the three land use types. In forest and grassland, the parameter uncertainty in NPS pollution was primarily associated with runoff processes, but in plantation, the main uncertain parameters were related to runoff process and soil properties. Taken together, the study suggested that adjusting the structure of land use and controlling fertilizer use are helpful methods to control the NPS pollution in the Daning River Watershed.

  2. Focusing Modeling of OPFC Linear Array Transducer by Using Distributed Point Source Method

    Directory of Open Access Journals (Sweden)

    Ziping Wang

    2014-01-01

    Full Text Available The improvement of ultrasonic phased array detection technology is a major concern of engineering community. Orthotropic piezoelectric fiber composite (OPFC can be constructed to multielement linear array which may be applied conveniently to actuators and sensors. The phased array transducers can generate special directional strong actuator power and high sensitivity for its orthotropic performance. Focusing beam of the linear phased array transducer is obtained simply only by adjusting a parabolic time delay. In this work, the distributed point source method (DPSM is used to model the ultrasonic field. DPSM is a newly developed mesh-free numerical technique that has been developed for solving a variety of engineering problems. This work gives the basic theory of this method and solves the problems from the application of new OPFC phased array transducer. Compared with traditional transducer, the interaction effect of two OPFC linear phased array transducers is also modeled in the same medium, which shows that the pressure beam produced by the new transducer is narrower or more collimated than that produced by the conventional transducer at different angles. DPSM can be used to analyze and optimally design the OPFC linear phased array transducer.

  3. Experienced versus Inexperienced Interexaminer Reliability on Location and Classification of Myofascial Trigger Point Palpation to Diagnose Lateral Epicondylalgia: An Observational Cross-Sectional Study

    Directory of Open Access Journals (Sweden)

    Raquel Mora-Relucio

    2016-01-01

    Full Text Available The purpose was to evaluate the interexaminer reliability of experienced and inexperienced examiners on location and classification of myofascial trigger points (MTrPs in two epicondylar muscles and the association between the MTrP found and the diagnosis of lateral epicondylalgia (LE. Fifty-two pianists (some suffered LE voluntarily participated in the study. Three physiotherapists (one inexperienced in myofascial pain examined, located, and marked MTrPs in the extensor carpi radialis brevis (ECRB and extensor digitorum communis (EDC muscles. Forearms were photographed and analyzed to establish the degree of agreement on MTrPs diagnosis. Data showed 81.73% and 77.88% of agreement on MTrP classification and 85.58% and 72.12% on MTrP location between the expert evaluators for ECRB and EDC, respectively. The agreement on MTrP classification between experienced and inexperienced examiners was 54.81% and 51.92% for ECRB and 50.00% and 55.77% for EDC. Also, agreement on MTrP location was 54.81% and 60.58% for ECRB and 48.08% and 48.08% for EDC. A strong association was found between presence of relevant MTrPs, LE diagnosis, and forearm pain when the examiners were experts. The analysis of location and classification of MTrPs in the epicondylar muscles through physical examination by experienced evaluators is reliable, reproducible, and suitable for diagnosing LE.

  4. Five-Level Z-Source Neutral Point-Clamped Inverter

    DEFF Research Database (Denmark)

    Gao, F.; Loh, P.C.; Blaabjerg, Frede

    2007-01-01

    This paper proposes a five-level Z-source neutralpoint- clamped (NPC) inverter with two Z-source networks functioning as intermediate energy storages coupled between dc sources and NPC inverter circuitry. Analyzing the operational principles of Z-source network with partial dclink shoot......-through scheme reveals the hidden theories in the five-level Z-source NPC inverter unlike the operational principle appeared in the general two-level Z-source inverter, so that the five-level Z-source NPC inverter can be designed with the modulation of carrier-based phase disposition (PD) or alternative phase...

  5. Five-Level Z-Source Neutral Point-Clamped Inverter

    DEFF Research Database (Denmark)

    Gao, F.; Loh, P.C.; Blaabjerg, Frede

    2007-01-01

    -through scheme reveals the hidden theories in the five-level Z-source NPC inverter unlike the operational principle appeared in the general two-level Z-source inverter, so that the five-level Z-source NPC inverter can be designed with the modulation of carrier-based phase disposition (PD) or alternative phase......This paper proposes a five-level Z-source neutralpoint- clamped (NPC) inverter with two Z-source networks functioning as intermediate energy storages coupled between dc sources and NPC inverter circuitry. Analyzing the operational principles of Z-source network with partial dclink shoot...

  6. Fault location and source process of the 2003 Boumerdes, Algeria, earthquake inferred from geodetic and strong motion data.

    Science.gov (United States)

    Semmane, F.; Campillo, M.; Cotton, F.

    2004-12-01

    The Boumerdes earthquake occurred on a fault which precise location, offshore the algerian coast, was unknown. Geodetic data consist of GPS measurements, levelling points and coastal uplifts. They are first used to determine the absolute position of the fault. We performed a series of inversions assuming different positions and chose the model giving the smallest misfit. According to this analysis, the fault emerge at about 15 km offshore. Accelerograms are then used to infer the space-time history of rupture on the fault plane using a two-step inversion in the spectral domain. The observed strong motion records are in good agreement with the synthetics for the fault location inferred from geodetic data. The fault plane ruptured for about 16 seconds. The slip distribution on the fault indicates one asperity north-west of the hypocenter with a maximum slip amplitude larger than 2.5 m. Another asperity with slightly smaller slip amplitude is located south-east of the hypocenter. The rupture seems to stop its propagation westward when it encounters the Thenia fault, a structure almost perpendicular to the main fault. We computed the spatial distribution of ground motion predicted by this fault model and compared it with the observed damages.

  7. Evaluation of spatial dependence of point spread function-based PET reconstruction using a traceable point-like 22Na source

    Directory of Open Access Journals (Sweden)

    Taisuke Murata

    2016-10-01

    Full Text Available Abstract Background The point spread function (PSF of positron emission tomography (PET depends on the position across the field of view (FOV. Reconstruction based on PSF improves spatial resolution and quantitative accuracy. The present study aimed to quantify the effects of PSF correction as a function of the position of a traceable point-like 22Na source over the FOV on two PET scanners with a different detector design. Methods We used Discovery 600 and Discovery 710 (GE Healthcare PET scanners and traceable point-like 22Na sources (<1 MBq with a spherical absorber design that assures uniform angular distribution of the emitted annihilation photons. The source was moved in three directions at intervals of 1 cm from the center towards the peripheral FOV using a three-dimensional (3D-positioning robot, and data were acquired over a period of 2 min per point. The PET data were reconstructed by filtered back projection (FBP, the ordered subset expectation maximization (OSEM, OSEM + PSF, and OSEM + PSF + time-of-flight (TOF. Full width at half maximum (FWHM was determined according to the NEMA method, and total counts in regions of interest (ROI for each reconstruction were quantified. Results The radial FWHM of FBP and OSEM increased towards the peripheral FOV, whereas PSF-based reconstruction recovered the FWHM at all points in the FOV of both scanners. The radial FWHM for PSF was 30–50 % lower than that of OSEM at the center of the FOV. The accuracy of PSF correction was independent of detector design. Quantitative values were stable across the FOV in all reconstruction methods. The effect of TOF on spatial resolution and quantitation accuracy was less noticeable. Conclusions The traceable 22Na point-like source allowed the evaluation of spatial resolution and quantitative accuracy across the FOV using different reconstruction methods and scanners. PSF-based reconstruction reduces dependence of the spatial resolution on the

  8. Biosolid stockpiles are a significant point source for greenhouse gas emissions.

    Science.gov (United States)

    Majumder, Ramaprasad; Livesley, Stephen J; Gregory, David; Arndt, Stefan K

    2014-10-01

    The wastewater treatment process generates large amounts of sewage sludge that are dried and then often stored in biosolid stockpiles in treatment plants. Because the biosolids are rich in decomposable organic matter they could be a significant source for greenhouse gas (GHG) emissions, yet there are no direct measurements of GHG from stockpiles. We therefore measured the direct emissions of methane (CH4), nitrous oxide (N2O) and carbon dioxide (CO2) on a monthly basis from three different age classes of biosolid stockpiles at the Western Treatment Plant (WTP), Melbourne, Australia, from December 2009 to November 2011 using manual static chambers. All biosolid stockpiles were a significant point source for CH4 and N2O emissions. The youngest biosolids (<1 year old) had the greatest CH4 and N2O emissions of 60.2 kg of CO2-e per Mg of biosolid per year. Stockpiles that were between 1 and 3 years old emitted less overall GHG (∼29 kg CO2-e Mg(-1) yr(-1)) and the oldest stockpiles emitted the least GHG (∼10 kg CO2-e Mg(-1) yr(-1)). Methane emissions were negligible in all stockpiles but the relative contribution of N2O and CO2 changed with stockpile age. The youngest stockpile emitted two thirds of the GHG emission as N2O, while the 1-3 year old stockpile emitted an equal amount of N2O and CO2 and in the oldest stockpile CO2 emissions dominated. We did not detect any seasonal variability of GHG emissions and did not observe a correlation between GHG flux and environmental variables such as biosolid temperature, moisture content or nitrate and ammonium concentration. We also modeled CH4 emissions based on a first order decay model and the model based estimated annual CH4 emissions were higher as compared to the direct field based estimated annual CH4 emissions. Our results indicate that labile organic material in stockpiles is decomposed over time and that nitrogen decomposition processes lead to significant N2O emissions. Carbon decomposition favors CO2 over

  9. The Treatment Train approach to reducing non-point source pollution from agriculture

    Science.gov (United States)

    Barber, N.; Reaney, S. M.; Barker, P. A.; Benskin, C.; Burke, S.; Cleasby, W.; Haygarth, P.; Jonczyk, J. C.; Owen, G. J.; Snell, M. A.; Surridge, B.; Quinn, P. F.

    2016-12-01

    An experimental approach has been applied to an agricultural catchment in NW England, where non-point pollution adversely affects freshwater ecology. The aim of the work (as part of the River Eden Demonstration Test Catchment project) is to develop techniques to manage agricultural runoff whilst maintaining food production. The approach used is the Treatment Train (TT), which applies multiple connected mitigation options that control nutrient and fine sediment pollution at source, and address polluted runoff pathways at increasing spatial scale. The principal agricultural practices in the study sub-catchment (1.5 km2) are dairy and stock production. Farm yards can act as significant pollution sources by housing large numbers of animals; these areas are addressed initially with infrastructure improvements e.g. clean/dirty water separation and upgraded waste storage. In-stream high resolution monitoring of hydrology and water quality parameters showed high-discharge events to account for the majority of pollutant exports ( 80% total phosphorus; 95% fine sediment), and primary transfer routes to be surface and shallow sub-surface flow pathways, including drains. To manage these pathways and reduce hydrological connectivity, a series of mitigation features were constructed to intercept and temporarily store runoff. Farm tracks, field drains, first order ditches and overland flow pathways were all targeted. The efficacy of the mitigation features has been monitored at event and annual scale, using inflow-outflow sampling and sediment/nutrient accumulation measurements, respectively. Data presented here show varied but positive results in terms of reducing acute and chronic sediment and nutrient losses. An aerial fly-through of the catchment is used to demonstrate how the TT has been applied to a fully-functioning agricultural landscape. The elevated perspective provides a better understanding of the spatial arrangement of mitigation features, and how they can be

  10. Spatial variability and source apportionment of PM2.5 across multiple sampling locations in southwest China

    Science.gov (United States)

    Shi, F.; Xie, S.

    2015-12-01

    The Chengdu Plain, which is located in the west of the Sichuan Basin, is the largest plain and the fastest-growing area in southwest China. The Chengdu Plain is considered one of the hotspot areas in China. The pollution pattern in this area is unique due to the hilly topography, humid and stagnant weather. To investigate the composition and major sources of the ambient PM2.5, a one-year observation was performed at five sites in the Chengdu Plain during August, 2013 to August, 2014. The five sites contained three urban background sites and two rural background sites. Samples were analyzed for major water-soluble ions, organic carbon (OC), element carbon (EC), and trace elements. The Positive Matrix Factorization (PMF) receptor model based on the combined data from five locations was applied to identify and quantify the likely sources. The annual mean mass concentration of PM2.5 in Chengdu Plain was 81 μg·m-3 with the maximum in winter and the minimum in summer. Eight main factors were identified for the PM2.5 fraction: vehicle emission, secondary nitrate, biomass burning and waste incineration emission, secondary sulfate, Mo-related manufacturing, fugitive dust, coal combustion and industry pollution. The five-site annual mean contributions of each source were 13%, 19%, 9%, 25%, 2%, 13%, 9% and 10%,respectively, to PM2.5, while exhibiting large spatial variability. The contribution of secondary sulfate to the PM2.5 mass was largest at all sites, indicating severe secondary pollution in the region. Biomass burning and waste incineration emission made larger proportion at rural sites than that of urban sites, while the vehicle emission was larger at urban sites. The Enrichment factors for Cd, Zn, Pb, As, Cu and Mo in PM2.5 were larger than 100 indicated that those elements were largely from anthropogenic origins. Cd, As and Cu can mainly originate from nonferrous metal industry, while Mo may mainly generated from ferromolybdenum and Mo powder manufacture. The

  11. Two Simon tasks with different sources of conflict: an ERP study of motion- and location-based compatibility effects.

    Science.gov (United States)

    Galashan, Daniela; Wittfoth, Matthias; Fehr, Thorsten; Herrmann, Manfred

    2008-07-01

    Behavioral and electrophysiological correlates of two Simon tasks were examined using comparable stimuli but different task-irrelevant and conflict-inducing stimulus features. Whereas target shape was always the task-relevant stimulus attribute, either target location (location-based task) or motion direction within the target stimuli (motion-based task) was used as a source of conflict. Data from ten healthy participants who performed both tasks are presented. In the motion-based task the incompatible condition showed smaller P300 amplitudes at Pz than the compatible condition and the location-based task yielded a trend towards a reduced P300 amplitude in the incompatible condition. For both tasks, no P300 latency differences between the conditions were found at Pz. The results suggest that the motion-based task elicits behavioral and electrophysiological effects comparable with regular Simon tasks. As all stimuli in the motion-based Simon task were presented centrally the present data strongly argue against the attention-shifting account as an explanatory approach.

  12. Consumption of added sugars among US children and adults by food purchase location and food source123

    Science.gov (United States)

    Drewnowski, Adam; Rehm, Colin D

    2014-01-01

    Background: The proposed changes to the Nutrition Facts Label by the US Food and Drug Administration will include information on added sugars for the first time. Objective: The objective was to evaluate the sources of added sugars in the diets of a representative sample of US children and adults by food purchase location and food source (eg, food group). Design: This cross-sectional study among 31,035 children, adolescents, and adults aged ≥6 y from the 2003–2004, 2005–2006, 2007–2008, and 2009–2010 NHANES used data from a 24-h dietary recall to evaluate consumption of added sugars. Food locations of origin were identified as stores (supermarket or grocery store), quick-service restaurants/pizza (QSRs), full-service restaurants (FSRs), schools, and others (eg, vending machines or gifts). Added sugars consumption by food purchase location was evaluated by age, family income-to-poverty ratio, and race-ethnicity. Food group sources of added sugars were identified by using the National Cancer Institute food categories. Results: Added sugars accounted for ∼14.1% of total dietary energy. Between 65% and 76% of added sugars came from stores, 6% and 12% from QSRs, and 4% and 6% from FSRs, depending on age. Older adults (aged ≥51 y) obtained a significantly greater proportion of added sugars from stores than did younger adults. Lower-income adults obtained a significantly greater proportion of added sugars from stores than did higher-income adults. Intake of added sugars did not vary by family income among children/adolescents. Soda and energy and sports drinks were the largest food group sources of added sugars (34.4%), followed by grain desserts (12.7%), fruit drinks (8.0%), candy (6.7%), and dairy desserts (5.6%). Conclusions: Most added sugars came from foods obtained from stores. The proposed changes to the Nutrition Facts Label should capture the bulk of added sugars in the US food supply, which suggests that the recommended changes have the potential to

  13. Sodium intakes of US children and adults from foods and beverages by location of origin and by specific food source.

    Science.gov (United States)

    Drewnowski, Adam; Rehm, Colin D

    2013-05-28

    Sodium intakes, from foods and beverages, of 22,852 persons in the National Health and Nutrition Examination Surveys (NHANES 2003-2008) were examined by specific food source and by food location of origin. Analyses were based on a single 24-h recall. Separate analyses were conducted for children (6-11 years of age), adolescents (12-19), and adults (20-50 and ≥51 years). Grouping of like foods (e.g., food sources) used a scheme proposed by the National Cancer Institute, which divides foods/beverages into 96 food subgroups (e.g., pizza, yeast breads or cold cuts). Food locations of origin were stores (e.g., grocery, convenience and specialty stores), quick-service restaurant/pizza (QSR), full-service restaurant (FSR), school, or other. Food locations of sodium were also evaluated by race/ethnicity amongst adults. Stores provided between 58.1% and 65.2% of dietary sodium, whereas QSR and FSR together provided between 18.9% and 31.8% depending on age. The proportion of sodium from QSR varied from 10.1% to 19.9%, whereas that from FSR varied from 3.4% to 13.3%. School meals provided 10.4% of sodium for 6-11 year olds and 6.0% for 12-19 year olds. Pizza from QSR, the top away from home food item, provided 5.4% of sodium in adolescents. QSR pizza, chicken, burgers and Mexican dishes combined provided 7.8% of total sodium in adult diets. Most sodium came from foods purchased in stores. Food manufacturers, restaurants, and grocery stores all have a role to play in reducing the amount of sodium in the American diet.

  14. New 20-cm radio-continuum study of the Small Magellanic Cloud, part II: Point sources

    Directory of Open Access Journals (Sweden)

    Wong G.F.

    2011-01-01

    Full Text Available We present a new catalogue of radio-continuum sources in the field of the Small Magellanic Cloud (SMC. This catalogue contains sources previously not found in 2370 MHz (λ=13 cm with sources found at 1400 MHz (λ=20 cm and 843 MHz (λ=36 cm. 45 sources have been detected at 13 cm, with 1560 sources at 20 cm created from new high sensitivity and resolution radio-continuum images of the SMC at 20 cm from paper I. We also created a 36 cm catalogue to which we listed 1689 radio-continuum sources.

  15. Reduction of non-point source contaminants associated with road-deposited sediments by sweeping.

    Science.gov (United States)

    Kim, Do-Gun; Kang, Hee-Man; Ko, Seok-Oh

    2017-09-19

    Road-deposited sediments (RDS) on an expressway, residual RDS collected after sweeping, and RDS removed by means of sweeping were analyzed to evaluate the degree to which sweeping removed various non-point source contaminants. The total RDS load was 393.1 ± 80.3 kg/km and the RDS, residual RDS, and swept RDS were all highly polluted with organics, nutrients, and metals. Among the metals studied, Cu, Zn, Pb, Ni, Ca, and Fe were significantly enriched, and most of the contaminants were associated with particles within the size range from 63 μm to 2 mm. Sweeping reduced RDS and its associated contaminants by 33.3-49.1% on average. We also measured the biological oxygen demand (BOD) of RDS in the present work, representing to our knowledge the first time that this has been done; we found that RDS contains a significant amount of biodegradable organics and that the reduction of BOD by sweeping was higher than that of other contaminants. Significant correlations were found between the contaminants measured, indicating that the organics and the metals originated from both exhaust and non-exhaust particles. Meanwhile, the concentrations of Cu and Ni were higher in 63 μm-2 mm particles than in smaller particles, suggesting that some metals in RDS likely exist intrinsically in particles, rather than only as adsorbates on particle surfaces. Overall, the results in this study showed that sweeping to collect RDS can be a good alternative for reduction of contaminants in runoff.

  16. Stochastic Management of Non-Point Source Contamination: Joint Impact of Aquifer Heterogeneity and Well Characteristics

    Science.gov (United States)

    Henri, C. V.; Harter, T.

    2017-12-01

    Agricultural activities are recognized as the preeminent origin of non-point source (NPS) contamination of water bodies through the leakage of nitrate, salt and agrochemicals. A large fraction of world agricultural activities and therefore NPS contamination occurs over unconsolidated alluvial deposit basins offering soil composition and topography favorable to productive farming. These basins represent also important groundwater reservoirs. The over-exploitation of aquifers coupled with groundwater pollution by agriculture-related NPS contaminant has led to a rapid deterioration of the quality of these groundwater basins. The management of groundwater contamination from NPS is challenged by the inherent complexity of aquifers systems. Contaminant transport dynamics are highly uncertain due to the heterogeneity of hydraulic parameters controlling groundwater flow. Well characteristics are also key uncertain elements affecting pollutant transport and NPS management but quantifying uncertainty in NPS management under these conditions is not well documented. Our work focuses on better understanding the joint impact of aquifer heterogeneity and pumping well characteristics (extraction rate and depth) on (1) the transport of contaminants from NPS and (2) the spatio-temporal extension of the capture zone. To do so, we generate a series of geostatistically equivalent 3D heterogeneous aquifers and simulate the flow and non-reactive solute transport from NPS to extraction wells within a stochastic framework. The propagation of the uncertainty on the hydraulic conductivity field is systematically analyzed. A sensitivity analysis of the impact of extraction well characteristics (pumping rate and screen depth) is also conducted. Results highlight the significant role that heterogeneity and well characteristics plays on management metrics. We finally show that, in case of NPS contamination, the joint impact of regional longitudinal and transverse vertical hydraulic gradients and

  17. Watershed-based point sources permitting strategy and dynamic permit-trading analysis.

    Science.gov (United States)

    Ning, Shu-Kuang; Chang, Ni-Bin

    2007-09-01

    Permit-trading policy in a total maximum daily load (TMDL) program may provide an additional avenue to produce environmental benefit, which closely approximates what would be achieved through a command and control approach, with relatively lower costs. One of the important considerations that might affect the effective trading mechanism is to determine the dynamic transaction prices and trading ratios in response to seasonal changes of assimilative capacity in the river. Advanced studies associated with multi-temporal spatially varied trading ratios among point sources to manage water pollution hold considerable potential for industries and policy makers alike. This paper aims to present an integrated simulation and optimization analysis for generating spatially varied trading ratios and evaluating seasonal transaction prices accordingly. It is designed to configure a permit-trading structure basin-wide and provide decision makers with a wealth of cost-effective, technology-oriented, risk-informed, and community-based management strategies. The case study, seamlessly integrating a QUAL2E simulation model with an optimal waste load allocation (WLA) scheme in a designated TMDL study area, helps understand the complexity of varying environmental resources values over space and time. The pollutants of concern in this region, which are eligible for trading, mainly include both biochemical oxygen demand (BOD) and ammonia-nitrogen (NH3-N). The problem solution, as a consequence, suggests an array of waste load reduction targets in a well-defined WLA scheme and exhibits a dynamic permit-trading framework among different sub-watersheds in the study area. Research findings gained in this paper may extend to any transferable dynamic-discharge permit (TDDP) program worldwide.

  18. Relationship Between Non-Point Source Pollution and Korean Green Factor

    Directory of Open Access Journals (Sweden)

    Seung Chul Lee

    2015-01-01

    Full Text Available In determining the relationship between the rational event mean concentration (REMC which is a volume-weighted mean of event mean concentrations (EMCs as a non-point source (NPS pollution indicator and the green factor (GF as a low impact development (LID land use planning indicator, we constructed at runoff database containing 1483 rainfall events collected from 107 different experimental catchments from 19 references in Korea. The collected data showed that EMCs were not correlated with storm factors whereas they showed significant differences according to the land use types. The calculated REMCs for BOD, COD, TSS, TN, and TP showed negative correlations with the GFs. However, even though the GFs of the agricultural area were concentrated in values of 80 like the green areas, the REMCs for TSS, TN, and TP were especially high. There were few differences in REMC runoff characteristics according to the GFs such as recreational facilities areas in suburbs and highways and trunk roads that connect to major roads between major cities. Except for those areas, the REMCs for BOD and COD were significantly related to the GFs. The REMCs for BOD and COD decreased when the rate of natural green area increased. On the other hand, some of the REMCs for TSS, TN, and TP were still high where the catchments encountered mixed land use patterns, especially public facility areas with bare ground and artificial grassland areas. The GF could therefore be used as a major planning indicator when establishing land use planning aimed at sustainable development with NPS management in urban areas if the weighted GF values will be improved.

  19. The Use of LiDAR Elevation Data and Satellite Imagery to Locate Critical Source Areas to Diffuse Pollution in Agricultural Watersheds

    Science.gov (United States)

    Drouin, Ariane; Michaud, Aubert; Thériault, Georges; Beaudin, Isabelle; Rodrigue, Jean-François; Denault, Jean-Thomas; Desjardins, Jacques; Côté, Noémi

    2013-04-01

    In Quebec / Canada, water quality improvement in rural areas greatly depends on the reduction of diffuse pollution. Indeed, point source pollution has been reduced significantly in Canada in recent years by creating circumscribed pits for manure and removing animals from stream. Diffuse pollution differs from point source pollution because it is spread over large areas. In agricultural areas, sediment loss by soil and riverbank erosion along with loss of nutrients (phosphorus, nitrogen, etc.) and pesticides from fields represent the main source of non-point source pollution. The factor mainly responsible for diffuse pollution in agricultural areas is surface runoff occurring in poorly drained areas in fields. The presence of these poorly drained areas is also one of the most limiting factors in crop productivity. Thus, a reconciliation of objectives at the farm (financial concern for farmers) and off-farm concerns (environmental concern) is possible. In short, drainage, runoff, erosion, water quality and crop production are all interconnected issues that need to be tackled together. Two complementary data sources are mainly used in the diagnosis of drainage, surface runoff and erosion : elevation data and multispectral satellite images. In this study of two watersheds located in Québec (Canada), LiDAR elevation data and satellite imagery (QuickBird, Spot and Landsat) were acquired. The studied territories have been partitioned in hydrologic response units (HRUs) according to sub-basins, soils, elevation (topographic index) and land use. These HRUs are afterwards used in a P index software (P-Edit) that calculates the quantities of sediments and phosphorus exported from each HRUs. These exports of sediments and phosphorus are validated with hydrometric and water quality data obtain in two sub-basins and are also compared to soil brightness index derived from multispectral images. This index is sensitive to soil moisture and thus highlights areas where the soil is

  20. Regional risk assessment for point source pollution based on a water quality model of the Taipu River, China.

    Science.gov (United States)

    Yao, Hong; Qian, Xin; Yin, Hong; Gao, Hailong; Wang, Yulei

    2015-02-01

    Point source pollution is one of the main threats to regional environmental health. Based on a water quality model, a methodology to assess the regional risk of point source pollution is proposed. The assessment procedure includes five parts: (1) identifying risk source units and estimating source emissions using Monte Carlo algorithms; (2) observing hydrological and water quality data of the assessed area, and evaluating the selected water quality model; (3) screening out the assessment endpoints and analyzing receptor vulnerability with the Choquet fuzzy integral algorithm; (4) using the water quality model introduced in the second step to predict pollutant concentrations for various source emission scenarios and analyzing hazards of risk sources; and finally, (5) using the source hazard values and receptor vulnerability scores to estimate overall regional risk. The proposed method, based on the Water Quality Analysis Simulation Program (WASP), was applied in the region of the Taipu River, which is in the Taihu Basin, China. Results of source hazard and receptor vulnerability analysis allowed us to describe aquatic ecological, human health, and socioeconomic risks individually, and also integrated risks in the Taipu region, from a series of risk curves. Risk contributions of sources to receptors were ranked, and the spatial distribution of risk levels was presented. By changing the input conditions, we were able to estimate risks for a range of scenarios. Thus, the proposed procedure may also be used by decisionmakers for long-term dynamic risk prediction. © 2014 Society for Risk Analysis.

  1. A system perspective on designing for field-dependent SNR in wide-angle point-source detection lenses

    Science.gov (United States)

    Olson, S. C.; Sparks, Andrew W.; Cline, Robert A.; Goodman, Timothy D.

    2017-05-01

    Lenses for staring-array point-source detection sensors must maintain good signal-to-noise ratio (SNR) over fields of view often exceeding 100 degrees. Such lenses typically have f-θ distortion to provide constant solid angle sampling in object space. While the relative illumination calculation is often used to describe flux transfer from a Lambertian extended object for imaging applications, maximizing SNR for point-source detection depends primarily on maximizing collected irradiance at the entrance pupil, the shape of which can vary dramatically over field. We illustrate this field-dependent SNR calculation with an example lens and outline the calculations needed to derive a simple aberration-based expression for the field dependence of point-source SNR.

  2. Status of the Ultracold neutron source upgrade at LANSCE [PowerPoint

    Energy Technology Data Exchange (ETDEWEB)

    Pattie Jr., Robert Wayne [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-31

    Several slides show the source and flux of ultracold neutrons produced. In summary, an upgraded UCN source has been designed, and parts are currently being fabricated. Nickel phosphorus-coated guides will improve transport to the experiment hall. The source will be installed in the spring of 2016 and commissioned in the fall of 2016.

  3. Oil pollution and microbiological quality of groundwater at the location of the water source 'Ratno ostrvo' nearby Novi Sad

    International Nuclear Information System (INIS)

    Petrovic, O.; Simeunovic, J.; Radnovic, D.; Matavulj, M.; Gajin, S.

    2002-01-01

    The 'Ratno ostrvo' is the biggest drinking water source in wider area of Novi Sad. It is located on the left bank of the river Danube near the Oil Refinery 'Novi Sad'. One of the consequences of the NATO bombing of the Oil Refinery 'Novi Sad' (which is placed in hinterland of the water source) was the uncontrolled spillage of crude oil and oil derivatives. Because of that, microbiological examinations of groundwaters, from both ecological and sanitary aspects were carried out simultaneously during post-war period. Microbiological analyses from sanitary aspects show very low number of coliform bacteria. Determination of numbers of bacteria of the investigated physiological groups, revealed that there was a constant relatively high number of oil-, phenol oxidizing and lipolytic bacteria which are indicators this kind of specific pollution. Microbiological analysis of oil polluted soil show presence relatively high number of different groups of bacteria. In spite of changed ecological situation caused by war effects, microbiological analyses of groundwater quality showed satisfactory results in source 'Ratno ostrvo' by now. The presence and potential activity of indigenous microflora could be utilized in recultivation processes in examined area. (author)

  4. Relative Source Locations of Continuous Tremor Before and After the Subplinian Events at Shinmoe-dake, in 2011

    Science.gov (United States)

    Ichihara, M.; Matsumoto, S.

    2017-11-01

    Volcano monitoring systems are not always ready to resolve signals at the onset of eruptive activity. This study makes use of stations installed later to calibrate the performance of the stations that had been operated before the eruption. Seven stations recorded continuous volcanic tremor before and during the subplinian eruptions of Shinmoe-dake, Japan, in 2011. We estimated the source locations of the tremor using the amplitude distribution. The stability of the analysis was obtained by careful selection of time windows in which signals from a single source are dominated. The site effects and the regional attenuation factor were evaluated using tremor recorded after the major eruptions by a dense seismic array and a good number of stations. A tremor source changed its depth beneath the crater for 1 week before the major eruption, rising from a depth of a few kilometer to the water layer 3 times, each of which occurred following shallow inflation and minor eruptions. It is interpreted as migration of gas probably with magma, which further transported heat to the water layer and triggered the subplinian eruptions.

  5. Effect of exposure history on microbial herbicide degradation in an aerobic aquifer affected by a point source

    DEFF Research Database (Denmark)

    Tuxen, Nina; de Lipthay, J.R.; Albrechtsen, Hans-Jørgen

    2002-01-01

    The effects of in situ exposure to low concentrations (micrograms per liter) of herbicides on aerobic degradation of herbicides in aquifers were studied by laboratory batch experiments. Aquifer material and groundwater were collected from a point source with known exposure histories to the herbic......The effects of in situ exposure to low concentrations (micrograms per liter) of herbicides on aerobic degradation of herbicides in aquifers were studied by laboratory batch experiments. Aquifer material and groundwater were collected from a point source with known exposure histories...

  6. Search of MeV-GeV counterparts of TeV sources with AGILE in pointing mode

    Science.gov (United States)

    Rappoldi, A.; Lucarelli, F.; Pittori, C.; Longo, F.; Cattaneo, P. W.; Verrecchia, F.; Tavani, M.; Bulgarelli, A.; Chen, A. W.; Colafrancesco, S.; Donnarumma, I.; Giuliani, A.; Morselli, A.; Sabatini, S.; Vercellone, S.

    2016-03-01

    Context. Known TeV sources detected by major Čerenkov telescopes are investigated to identify possible MeV-GeV γ-ray counterparts. Aims: A systematic study of the known sources in the web-based TeVCat catalog has been performed to search for possible γ-ray counterparts on the AGILE data collected during the first period of operations in observing pointing mode. Methods: For each TeV source, a search for a possible γ-ray counterpart that is based on a multi-source maximum likelihood algorithm is performed on the AGILE data taken with the GRID instrument from July 2007 to October 2009. Results: In the case of high-significance detection, the average γ-ray flux is estimated. For cases of low-significance detection the 95% confidence level (CL) flux upper limit is given. 52 TeV sources out of 152 (corresponding to ~34% of the analysed sample) show a significant excess in the AGILE data covering the pointing observation period. Conclusions: This analysis found 26 new AGILE sources with respect to the AGILE reference catalogs, 15 of which are galactic, 7 are extragalactic and 4 are unidentified. Detailed tables with all available information on the analysed sources are presented. An interactive online version of the considered source list including all the analysis results is also available at the website http://www.asdc.asi.it/agiletevcat/

  7. Modelling the transport of solid contaminants originated from a point source

    Science.gov (United States)

    Salgueiro, Dora V.; Conde, Daniel A. S.; Franca, Mário J.; Schleiss, Anton J.; Ferreira, Rui M. L.

    2017-04-01

    The solid phases of natural flows can comprise an important repository for contaminants in aquatic ecosystems and can propagate as turbidity currents generating a stratified environment. Contaminants can be desorbed under specific environmental conditions becoming re-suspended, with a potential impact on the aquatic biota. Forecasting the distribution of the contaminated turbidity current is thus crucial for a complete assessment of environmental exposure. In this work we validate the ability of the model STAV-2D, developed at CERIS (IST), to simulate stratified flows such as those resulting from turbidity currents in complex geometrical environments. The validation involves not only flow phenomena inherent to flows generated by density imbalance but also convective effects brought about by the complex geometry of the water basin where the current propagates. This latter aspect is of paramount importance since, in real applications, currents may propagate in semi-confined geometries in plan view, generating important convective accelerations. Velocity fields and mass distributions obtained from experiments carried out at CERIS - (IST) are used as validation data for the model. The experimental set-up comprises a point source in a rectangular basin with a wall placed perpendicularly to the outer walls. Thus generates a complex 2D flow with an advancing wave front and shocks due to the flow reflection from the walls. STAV-2D is based on the depth- and time-averaged mass and momentum equations for mixtures of water and sediment, understood as continua. It is closed in terms of flow resistance and capacity bedload discharge by a set of classic closure models and a specific high concentration formulation. The two-layer model is derived from layer-averaged Navier-Stokes equations, resulting in a system of layer-specific non-linear shallow-water equations, solved through explicit first or second-order schemes. According to the experimental data for mass distribution, the

  8. Modeling non-point source pollutants in the vadose zone: Back to the basics

    Science.gov (United States)

    Corwin, Dennis L.; Letey, John, Jr.; Carrillo, Marcia L. K.

    More than ever before in the history of scientific investigation, modeling is viewed as a fundamental component of the scientific method because of the relatively recent development of the computer. No longer must the scientific investigator be confined to artificially isolated studies of individual processes that can lead to oversimplified and sometimes erroneous conceptions of larger phenomena. Computer models now enable scientists to attack problems related to open systems such as climatic change, and the assessment of environmental impacts, where the whole of the interactive processes are greater than the sum of their isolated components. Environmental assessment involves the determination of change of some constituent over time. This change can be measured in real time or predicted with a model. The advantage of prediction, like preventative medicine, is that it can be used to alter the occurrence of potentially detrimental conditions before they are manifest. The much greater efficiency of preventative, rather than remedial, efforts strongly justifies the need for an ability to accurately model environmental contaminants such as non-point source (NPS) pollutants. However, the environmental modeling advances that have accompanied computer technological development are a mixed blessing. Where once we had a plethora of discordant data without a holistic theory, now the pendulum has swung so that we suffer from a growing stockpile of models of which a significant number have never been confirmed or even attempts made to confirm them. Modeling has become an end in itself rather than a means because of limited research funding, the high cost of field studies, limitations in time and patience, difficulty in cooperative research and pressure to publish papers as quickly as possible. Modeling and experimentation should be ongoing processes that reciprocally enhance one another with sound, comprehensive experiments serving as the building blocks of models and models

  9. Point source detection using the Spherical Mexican Hat Wavelet on simulated all-sky Planck maps

    Science.gov (United States)

    Vielva, P.; Martínez-González, E.; Gallegos, J. E.; Toffolatti, L.; Sanz, J. L.

    2003-09-01

    We present an estimation of the point source (PS) catalogue that could be extracted from the forthcoming ESA Planck mission data. We have applied the Spherical Mexican Hat Wavelet (SMHW) to simulated all-sky maps that include cosmic microwave background (CMB), Galactic emission (thermal dust, free-free and synchrotron), thermal Sunyaev-Zel'dovich effect and PS emission, as well as instrumental white noise. This work is an extension of the one presented in Vielva et al. We have developed an algorithm focused on a fast local optimal scale determination, that is crucial to achieve a PS catalogue with a large number of detections and a low flux limit. An important effort has been also done to reduce the CPU time processor for spherical harmonic transformation, in order to perform the PS detection in a reasonable time. The presented algorithm is able to provide a PS catalogue above fluxes: 0.48 Jy (857 GHz), 0.49 Jy (545 GHz), 0.18 Jy (353 GHz), 0.12 Jy (217 GHz), 0.13 Jy (143 GHz), 0.16 Jy (100 GHz HFI), 0.19 Jy (100 GHz LFI), 0.24 Jy (70 GHz), 0.25 Jy (44 GHz) and 0.23 Jy (30 GHz). We detect around 27 700 PS at the highest frequency Planck channel and 2900 at the 30-GHz one. The completeness level are: 70 per cent (857 GHz), 75 per cent (545 GHz), 70 per cent (353 GHz), 80 per cent (217 GHz), 90 per cent (143 GHz), 85 per cent (100 GHz HFI), 80 per cent (100 GHz LFI), 80 per cent (70 GHz), 85 per cent (44 GHz) and 80 per cent (30 GHz). In addition, we can find several PS at different channels, allowing the study of the spectral behaviour and the physical processes acting on them. We also present the basic procedure to apply the method in maps convolved with asymmetric beams. The algorithm takes ~72 h for the most CPU time-demanding channel (857 GHz) in a Compaq HPC320 (Alpha EV68 1-GHz processor) and requires 4 GB of RAM memory; the CPU time goes as O[NRoN3/2pix log(Npix)], where Npix is the number of pixels in the map and NRo is the number of optimal scales needed.

  10. Taming the beast : Free and open-source massive point cloud web visualization

    NARCIS (Netherlands)

    Martinez-Rubi, O.; Verhoeven, S.; Van Meersbergen, M.; Schûtz, M.; Van Oosterom, P.; Gonçalves, R.; Tijssen, T.

    2015-01-01

    Powered by WebGL, some renderers have recently become available for the visualization of point cloud data over the web, for example Plasio or Potree. We have extended Potree to be able to visualize massive point clouds and we have successfully used it with the second national Lidar survey of the

  11. Contaminant dispersion prediction and source estimation with integrated Gaussian-machine learning network model for point source emission in atmosphere

    International Nuclear Information System (INIS)

    Ma, Denglong; Zhang, Zaoxiao

    2016-01-01

    Highlights: • The intelligent network models were built to predict contaminant gas concentrations. • The improved network models coupled with Gaussian dispersion model were presented. • New model has high efficiency and accuracy for concentration prediction. • New model were applied to indentify the leakage source with satisfied results. - Abstract: Gas dispersion model is important for predicting the gas concentrations when contaminant gas leakage occurs. Intelligent network models such as radial basis function (RBF), back propagation (BP) neural network and support vector machine (SVM) model can be used for gas dispersion prediction. However, the prediction results from these network models with too many inputs based on original monitoring parameters are not in good agreement with the experimental data. Then, a new series of machine learning algorithms (MLA) models combined classic Gaussian model with MLA algorithm has been presented. The prediction results from new models are improved greatly. Among these models, Gaussian-SVM model performs best and its computation time is close to that of classic Gaussian dispersion model. Finally, Gaussian-MLA models were applied to identifying the emission source parameters with the particle swarm optimization (PSO) method. The estimation performance of PSO with Gaussian-MLA is better than that with Gaussian, Lagrangian stochastic (LS) dispersion model and network models based on original monitoring parameters. Hence, the new prediction model based on Gaussian-MLA is potentially a good method to predict contaminant gas dispersion as well as a good forward model in emission source parameters identification problem.

  12. Maximum Power Point Tracking Implementation by Dspace Controller Integrated Through Z-Source Inverter Using Particle Swarm Optimization Technique for Photovoltaic Applications

    Directory of Open Access Journals (Sweden)

    Kalaiarasi N.

    2018-01-01

    Full Text Available Maximum Power Point Tracking (MPPT technique is used to extract maximum power from the photovoltaic system. This paper involves working on an enhanced Particle Swarm Optimization (PSO based MPPT method for the photovoltaic (PV system integrated through Z-Source inverter. The main benefit of the proposed method is the diminishing of the steady-state oscillation when the maximum power point (MPP is located. Additionally, during an extreme environmental condition, such as partial shading and large fluctuations of irradiance and temperature, the proposed method has the capability to track the MPP. This algorithm is implemented in dspace 1104 controller. MATLAB simulations are carried out under varying irradiance and temperature conditions to evaluate its effectiveness. Its performance is compared with a conventional method like Perturb and observe (P&O method.

  13. Design and evaluation of aircraft heat source systems for use with high-freezing point fuels

    Science.gov (United States)

    Pasion, A. J.

    1979-01-01

    The objectives were the design, performance and economic analyses of practical aircraft fuel heating systems that would permit the use of high freezing-point fuels on long-range aircraft. Two hypothetical hydrocarbon fuels with freezing points of -29 C and -18 C were used to represent the variation from current day jet fuels. A Boeing 747-200 with JT9D-7/7A engines was used as the baseline aircraft. A 9300 Km mission was used as the mission length from which the heat requirements to maintain the fuel above its freezing point was based.

  14. Seeing the Point: Using Visual Sources to Understand the Arguments for Women's Suffrage

    Science.gov (United States)

    Card, Jane

    2011-01-01

    Visual sources, Jane Card argues, are a powerful resource for historical learning but using them in the classroom requires careful thought and planning. Card here shares how she has used visual source material in order to teach her students about the women's suffrage movement. In particular, Card shows how a chain of questions that moves from the…

  15. THERMAL NEUTRON INTENSITIES IN SOILS IRRADIATED BY FAST NEUTRONS FROM POINT SOURCES. (R825549C054)

    Science.gov (United States)

    Thermal-neutron fluences in soil are reported for selected fast-neutron sources, selected soil types, and selected irradiation geometries. Sources include 14 MeV neutrons from accelerators, neutrons from spontaneously fissioning 252Cf, and neutrons produced from alp...

  16. Risk-based prioritisation of point sources through assessment of the impact on a water supply

    DEFF Research Database (Denmark)

    Overheu, Niels D.; Tuxen, Nina; Troldborg, Mads

    2011-01-01

    vulnerability mapping, site-specific mass flux estimates on a local scale from all the sources, and 3-D catchment-scale fate and transport modelling. It handles sources at various knowledge levels and accounts for uncertainties. The tool estimates the impacts on the water supply in the catchment and provides...

  17. Improved Point-source Detection in Crowded Fields Using Probabilistic Cataloging

    Science.gov (United States)

    Portillo, Stephen K. N.; Lee, Benjamin C. G.; Daylan, Tansu; Finkbeiner, Douglas P.

    2017-10-01

    Cataloging is challenging in crowded fields because sources are extremely covariant with their neighbors and blending makes even the number of sources ambiguous. We present the first optical probabilistic catalog, cataloging a crowded (˜0.1 sources per pixel brighter than 22nd mag in F606W) Sloan Digital Sky Survey r-band image from M2. Probabilistic cataloging returns an ensemble of catalogs inferred from the image and thus can capture source-source covariance and deblending ambiguities. By comparing to a traditional catalog of the same image and a Hubble Space Telescope catalog of the same region, we show that our catalog ensemble better recovers sources from the image. It goes more than a magnitude deeper than the traditional catalog while having a lower false-discovery rate brighter than 20th mag. We also present an algorithm for reducing this catalog ensemble to a condensed catalog that is similar to a traditional catalog, except that it explicitly marginalizes over source-source covariances and nuisance parameters. We show that this condensed catalog has a similar completeness and false-discovery rate to the catalog ensemble. Future telescopes will be more sensitive, and thus more of their images will be crowded. Probabilistic cataloging performs better than existing software in crowded fields and so should be considered when creating photometric pipelines in the Large Synoptic Survey Telescope era.

  18. NuSTAR Hard X-Ray Survey of the Galactic Center Region. II. X-Ray Point Sources

    DEFF Research Database (Denmark)

    Hong, JaeSub; Mori, Kaya; Hailey, Charles J.

    2016-01-01

    We present the first survey results of hard X-ray point sources in the Galactic Center (GC) region by NuSTAR. We have discovered 70 hard (3-79 keV) X-ray point sources in a 0.6 deg2 region around Sgr A* with a total exposure of 1.7 Ms, and 7 sources in the Sgr B2 field with 300 ks. We identify...... persistent luminous X-ray binaries (XBs) and the likely run-away pulsar called the Cannonball. New source-detection significance maps reveal a cluster of hard (>10 keV) X-ray sources near the Sgr. A diffuse complex with no clear soft X-ray counterparts. The severe extinction observed in the Chandra spectra...... indicate that the X-ray spectra of the NuSTAR sources should have kT > 20 keV on average for a single temperature thermal plasma model or an average photon index of Gamma = 1.5-2 for a power-law model. These findings suggest that the GC X-ray source population may contain a larger fraction of XBs with high...

  19. MP3DG-PCC, open source software framework for implementation and evaluation of point cloud compression

    NARCIS (Netherlands)

    R.N. Mekuria (Rufael); P.S. Cesar Garcia (Pablo Santiago)

    2016-01-01

    textabstractWe present MP3DG-PCC, an open source framework for design, implementation and evaluation of point cloud compression algorithms. The framework includes objective quality metrics, lossy and lossless anchor codecs, and a test bench for consistent comparative evaluation. The framework and

  20. Long-term vegetation landscape pattern with non-point source nutrient pollution in upper stream of Yellow River basin

    NARCIS (Netherlands)

    Ouyang, W.; Skidmore, A.K.; Toxopeus, A.G.; Hao, F.

    2010-01-01

    Grassland, forest, and farmland are the dominant land covers in upper catchments of the Yellow River and their landscape status has direct connection with dynamics of non-point source (NPS) pollution. Understanding the correlations between landscape variables and different formats of NPS nutrients

  1. Point Sources of Emerging Contaminants Along the Colorado River Basin: Impact on Water Use and Reuse in the Arid Southwest

    Science.gov (United States)

    Emerging contaminants (ECs) (e.g., pharmaceuticals, illicit drugs, personal care products) have been detected in waters across the United States. The objective of this study was to evaluate point sources of ECs along the Colorado River, from the headwaters in Colorado to the Gulf...

  2. Estimation of non-point source pollution loads by improvising export coefficient model in watershed with a modified planting pattern

    Science.gov (United States)

    Dong, F.; Liu, X. B.; Peng, W. Q.; Wang, L.

    2017-08-01

    Export coefficient model was improved to calculate and compare non-point source pollution loads in an agricultural watershed before and after implanting new cropping pattern. The modification was done by introducing the reduction coefficient in consumption amount and loss load as well as the proportion of bioactive ingredients of fertilizer and pesticide to the export coefficient model developed by Johnes in 1996. The modified export coefficient model was then applied to estimate non-point source pollution load in Gaoxi community, Yunnan Province, China where a water-saving and emission reduction technology was implemented by changing cropping pattern. Study results showed that the improved export coefficient model had a favorable flexibility in calculating the non-point source pollution loads and well applicable to the watersheds where various input data is in short. Moreover, the findings will provide scientific basis to understand the variability of non-point source pollutants in agricultural watersheds and their load estimation in order to optimize the efficiency of pollutants reduction plan implemented through agricultural adjustment.

  3. Searches for Extended and Point-like Neutrino Sources with Four Years of IceCube Data

    DEFF Research Database (Denmark)

    Aartsen, M.G.; Ackermann, M.; Adams, J.

    2014-01-01

    We present results on searches for point-like sources of neutrinos using four years of IceCube data, including the first year of data from the completed 86 string detector. The total livetime of the combined data set is 1373 days. For an E –2 spectrum, the observed 90% C.L. flux upper limits are ...

  4. Effects of pointing compared with naming and observing during encoding on item and source memory in young and older adults

    NARCIS (Netherlands)

    Ouwehand, Kim; Gog, Tamara van; Paas, Fred

    2016-01-01

    Research showed that source memory functioning declines with ageing. Evidence suggests that encoding visual stimuli with manual pointing in addition to visual observation can have a positive effect on spatial memory compared with visual observation only. The present study investigated whether

  5. Source contributions to PM2.5 and PM10 at an urban background and a street location

    Science.gov (United States)

    Keuken, M. P.; Moerman, M.; Voogt, M.; Blom, M.; Weijers, E. P.; Röckmann, T.; Dusek, U.

    2013-06-01

    The contribution of regional, urban and traffic sources to PM2.5 and PM10 in an urban area was investigated in this study. The chemical composition of PM2.5 and PM10 was measured over a year at a street location and up- and down-wind of the city of Rotterdam, the Netherlands. The 14C content in EC and OC concentrations was also determined, to distinguish the contribution from "modern" carbon (e.g., biogenic emissions, biomass burning and wildfires) and fossil fuel combustion. It was concluded that the urban background of PM2.5 and PM10 is dominated by the regional background, and that primary and secondary PM emission by urban sources contribute less than 15%. The 14C analysis revealed that 70% of OC originates from modern carbon and 30% from fossil fuel combustion. The corresponding percentages for EC are, respectively 17% and 83%. It is concluded that in particular the urban population living in street canyons with intense road traffic has potential health risks. This is due to exposure to elevated concentrations of a factor two for EC from exhaust emissions in PM2.5 and a factor 2-3 for heavy metals from brake and tyre wear, and re-suspended road dust in PM10. It follows that local air quality management may focus on local measures to street canyons with intense road traffic.

  6. Study of infrared point source simulator for generating the multi-decoy

    Science.gov (United States)

    Zeng, Chang-e.; Yang, Di; Su, Jian-gang; Huang, Yan-jun; Wang, Zhi-sheng

    2013-08-01

    The hardware-in-loop test system for infrared point-type guide missile was introduced;The decoy irradiation and motion characteristics were analyzed; multi-decoy generation mode and principle were studied.

  7. Fibre intake and incident colorectal cancer depending on fibre source, sex, tumour location and Tumour, Node, Metastasis stage.

    Science.gov (United States)

    Vulcan, Alexandra; Brändstedt, Jenny; Manjer, Jonas; Jirström, Karin; Ohlsson, Bodil; Ericson, Ulrika

    2015-09-28

    Studies on fibre intake and incident colorectal cancer (CRC) indicate inverse associations. Differences by tumour stage have not been examined. We examined associations between fibre intake and its sources, and incidental CRC. Separate analyses were carried out on the basis of sex, tumour location and the Tumour, Node, Metastasis (TNM) classification. The Malmö Diet and Cancer Study is a population-based cohort study, including individuals aged 45-74 years. Dietary data were collected through a modified diet history method. The TNM classification was obtained from pathology/clinical records and re-evaluated. Among 27 931 individuals (60% women), we found 728 incident CRC cases during 428 924 person-years of follow-up. Fibre intake was inversely associated with CRC risk (P(trend) = 0.026). Concerning colon cancer, we observed borderline interaction between fibre intake and sex (P = 0.052) and significant protective association restricted to women (P(trend) = 0.013). Intake of fruits and berries was inversely associated with colon cancer in women (P(trend) = 0.022). We also observed significant interactions between intakes of fibre (P = 0.048) and vegetables (P = 0.039) and sex on rectal cancer, but no significant associations were seen between intake of fibre, or its sources, in either of the sexes. Except for inverse associations between intake of fibre-rich cereal products and N0- and M0-tumours, we did not observe significant associations with different TNM stages. Our findings suggest different associations between fibre intake and CRC depending on sex, tumour site and fibre source. High fibre intake, especially from fruits and berries, may, above all, prevent tumour development in the colon in women. No clear differences by TNM classification were detected.

  8. The Potential for Electrofuels Production in Sweden Utilizing Fossil and Biogenic CO{sub 2} Point Sources

    Energy Technology Data Exchange (ETDEWEB)

    Hansson, Julia, E-mail: julia.hansson@ivl.se [Climate and Sustainable Cities, IVL Swedish Environmental Research Institute, Stockholm (Sweden); Division of Physical Resource Theory, Department of Energy and Environment, Chalmers University of Technology, Göteborg (Sweden); Hackl, Roman [Climate and Sustainable Cities, IVL Swedish Environmental Research Institute, Stockholm (Sweden); Taljegard, Maria [Division of Energy Technology, Department of Energy and Environment, Chalmers University of Technology, Göteborg (Sweden); Brynolf, Selma; Grahn, Maria [Division of Physical Resource Theory, Department of Energy and Environment, Chalmers University of Technology, Göteborg (Sweden)

    2017-03-13

    This paper maps, categorizes, and quantifies all major point sources of carbon dioxide (CO{sub 2}) emissions from industrial and combustion processes in Sweden. The paper also estimates the Swedish technical potential for electrofuels (power-to-gas/fuels) based on carbon capture and utilization. With our bottom-up approach using European databases, we find that Sweden emits approximately 50 million metric tons of CO{sub 2} per year from different types of point sources, with 65% (or about 32 million tons) from biogenic sources. The major sources are the pulp and paper industry (46%), heat and power production (23%), and waste treatment and incineration (8%). Most of the CO{sub 2} is emitted at low concentrations (<15%) from sources in the southern part of Sweden where power demand generally exceeds in-region supply. The potentially recoverable emissions from all the included point sources amount to 45 million tons. If all the recoverable CO{sub 2} were used to produce electrofuels, the yield would correspond to 2–3 times the current Swedish demand for transportation fuels. The electricity required would correspond to about 3 times the current Swedish electricity supply. The current relatively few emission sources with high concentrations of CO{sub 2} (>90%, biofuel operations) would yield electrofuels corresponding to approximately 2% of the current demand for transportation fuels (corresponding to 1.5–2 TWh/year). In a 2030 scenario with large-scale biofuels operations based on lignocellulosic feedstocks, the potential for electrofuels production from high-concentration sources increases to 8–11 TWh/year. Finally, renewable electricity and production costs, rather than CO{sub 2} supply, limit the potential for production of electrofuels in Sweden.

  9. The 100 Strongest Radio Point Sources in the Field of the Large Magellanic Cloud at 1.4 GHz

    Directory of Open Access Journals (Sweden)

    Payne, J. L.

    2009-06-01

    Full Text Available We present the 100 strongest 1.4~GHz point sources from a new mosaicimage in the direction of the Large Magellanic Cloud (LMC. The observationsmaking up the mosaic were made using Australia Telescope Compact Array (ATCAover a ten year period and were combined with Parkes single dish data at 1.4 GHz to complete the image for short spacing. An initial list of co-identifications within 10arcsec at 0.843, 4.8 and 8.6 GHz consisted of 2682 sources. Elimination of extended objects and artifact noise allowed the creation of a refined list containing 1988 point sources. Most of these are presumed to be background objects seen through the LMC; a small portion may represent compact HII regions, young SNRs and radio planetary nebulae. For the 1988 point sources we find a preliminary average spectral index ($alpha$ of -0.53 and present a 1.4 GHz image showing source locationin the direction of the LMC.

  10. Implications of wall recycling and carbon source locations on core plasma fueling and impurity content in DIII-D

    International Nuclear Information System (INIS)

    Groth, M.; Porter, G.D.; Fenstermacher, M.E.; Lasnier, C.J.; Meyer, W.M.; Rensink, M.E.; Wolf, N.S.; Boedo, J.A.; Moyer, R.A.; Rudakov, D.L.; Brooks, N.H.; Groebner, R.J.; Petrie, T.W.; Owen, L.W.; Wang, G.; Zeng, L.; Watkins, J.G.

    2005-01-01

    Measurement and modeling of the 2-D poloidal D α intensity distribution in DIII-D low and medium density L-mode and ELMy H-mode plasmas indicate that hydrogen neutrals predominantly fuel the core from the divertor X-point region. The 2-D distribution of neutral deuterium and low-charge-state carbon were measured in the divertor and the high-field side midplane scrape-off layer (SOL) using tangentially viewing cameras. The emission in the high-field SOL at the equatorial plane was found to be three to four orders of magnitude lower than at the strike points in the divertor, suggesting a strong divertor particle source. Modeling using the UEDGE/DEGAS codes predicted the poloidal fueling distribution to be dependent on the direction of the ion Bx∇B drift. In plasmas with the Bx∇B drift into the divertor stronger fueling from the inner divertor than from the outer is predicted, due to a lower-temperature and higher-density plasma in the inner leg. UEDGE simulations with carbon produced by both physical and chemical sputtering at the divertor plates and walls only are in agreement with a large set of diagnostic data. The simulations indicate flow reversal in the inner divertor that augments the leakage of carbon ions from the divertor into the core. (author)

  11. Impact of Point and Non-point Source Pollution on Coral Reef Ecosystems In Mamala Bay, Oahu, Hawaii based on Water Quality Measurements and Benthic Surveys in 1993-1994 (NODC Accession 0001172)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The effects of both point and non-point sources of pollution on coral reef ecosystems in Mamala Bay were studied at three levels of biological organization; the...

  12. Comparison of point-source pollutant loadings to soil and groundwater for 72 chemical substances.

    Science.gov (United States)

    Yu, Soonyoung; Hwang, Sang-Il; Yun, Seong-Taek; Chae, Gitak; Lee, Dongsu; Kim, Ki-Eun

    2017-11-01

    Fate and transport of 72 chemicals in soil and groundwater were assessed by using a multiphase compositional model (CompFlow Bio) because some of the chemicals are non-aqueous phase liquids or solids in the original form. One metric ton of chemicals were assumed to leak in a stylized facility. Scenarios of both surface spills and subsurface leaks were considered. Simulation results showed that the fate and transport of chemicals above the water table affected the fate and transport of chemicals below the water table, and vice versa. Surface spill scenarios caused much less concentrations than subsurface leak scenarios because leaching amounts into the subsurface environment were small (at most 6% of the 1 t spill for methylamine). Then, simulation results were applied to assess point-source pollutant loadings to soil and groundwater above and below the water table, respectively, by multiplying concentrations, impact areas, and durations. These three components correspond to the intensity of contamination, mobility, and persistency in the assessment of pollutant loading, respectively. Assessment results showed that the pollutant loadings in soil and groundwater were linearly related (r 2  = 0.64). The pollutant loadings were negatively related with zero-order and first-order decay rates in both soil (r = - 0.5 and - 0.6, respectively) and groundwater (- 1.0 and - 0.8, respectively). In addition, this study scientifically defended that the soil partitioning coefficient (K d ) significantly affected the pollutant loadings in soil (r = 0.6) and the maximum masses in groundwater (r = - 0.9). However, K d was not a representative factor for chemical transportability unlike the expectation in chemical ranking systems of soil and groundwater pollutants. The pollutant loadings estimated using a physics-based hydrogeological model provided a more rational ranking for exposure assessment, compared to the summation of persistency and transportability scores in

  13. Optimizing the calculation of point source count-centroid in pixel size measurement

    International Nuclear Information System (INIS)

    Zhou Luyi; Kuang Anren; Su Xianyu

    2004-01-01

    Pixel size is an important parameter of gamma camera and SPECT. A number of methods are used for its accurate measurement. In the original count-centroid method, where the image of a point source (PS) is acquired and its count-centroid calculated to represent PS position in the image, background counts are inevitable. Thus the measured count-centroid (X m ) is an approximation of the true count-centroid (X p ) of the PS, i.e. X m =X p + (X b -X p )/(1+R p /R b ), where Rp is the net counting rate of the PS, X b the background count-centroid and Rb the background counting. To get accurate measurement, R p must be very big, which is unpractical, resulting in the variation of measured pixel size. R p -independent calculation of PS count-centroid is desired. Methods: The proposed method attempted to eliminate the effect of the term (X b -X p )/(1 + R p /R b ) by bringing X b closer to X p and by reducing R b . In the acquired PS image, a circular ROI was generated to enclose the PS, the pixel with the maximum count being the center of the ROI. To choose the diameter (D) of the ROI, a Gaussian count distribution was assumed for the PS, accordingly, K=1-(0.5) D/R percent of the total PS counts was in the ROI, R being the full width at half maximum of the PS count distribution. D was set to be 6*R to enclose most (K=98.4%) of the PS counts. The count-centroid of the ROI was calculated to represent X p . The proposed method was tested in measuring the pixel size of a well-tuned SPECT, whose pixel size was estimated to be 3.02 mm according to its mechanical and electronic setting (128 x 128 matrix, 387 mm UFOV, ZOOM=1). For comparison, the original method, which was use in the former versions of some commercial SPECT software, was also tested. 12 PSs were prepared and their image acquired and stored. The net counting rate of the PSs increased from 10 cps to 1183 cps. Results: Using the proposed method, the measured pixel size (in mm) varied only between 3.00 and 3.01 (mean

  14. Optimizing the calculation of point source count-centroid in pixel size measurement

    International Nuclear Information System (INIS)

    Zhou Luyi; Kuang Anren; Su Xianyu

    2004-01-01

    Purpose: Pixel size is an important parameter of gamma camera and SPECT. A number of Methods are used for its accurate measurement. In the original count-centroid method, where the image of a point source(PS) is acquired and its count-centroid calculated to represent PS position in the image, background counts are inevitable. Thus the measured count-centroid (Xm) is an approximation of the true count-centroid (Xp) of the PS, i.e. Xm=Xp+(Xb-Xp)/(1+Rp/Rb), where Rp is the net counting rate of the PS, Xb the background count-centroid and Rb the background counting rate. To get accurate measurement, Rp must be very big, which is unpractical, resulting in the variation of measured pixel size. Rp-independent calculation of PS count-centroid is desired. Methods: The proposed method attempted to eliminate the effect of the term (Xb-Xp)/(1+Rp/Rb) by bringing Xb closer to Xp and by reducing Rb. In the acquired PS image, a circular ROI was generated to enclose the PS, the pixel with the maximum count being the center of the ROI. To choose the diameter (D) of the ROI, a Gaussian count distribution was assumed for the PS, accordingly, K=I-(0.5)D/R percent of the total PS counts was in the ROI, R being the full width at half maximum of the PS count distribution. D was set to be 6*R to enclose most (K=98.4%) of the PS counts. The count-centroid of the ROI was calculated to represent Xp. The proposed method was tested in measuring the pixel size of a well-tuned SPECT, whose pixel size was estimated to be 3.02 mm according to its mechanical and electronic setting (128*128 matrix, 387 mm UFOV, ZOOM=1). For comparison, the original method, which was use in the former versions of some commercial SPECT software, was also tested. 12 PSs were prepared and their image acquired and stored. The net counting rate of the PSs increased from 10cps to 1183cps. Results: Using the proposed method, the measured pixel size (in mm) varied only between 3.00 and 3.01( mean= 3.01±0.00) as Rp increased

  15. The simulation research of dissolved nitrogen and phosphorus non-point source pollution in Xiao-Jiang watershed of Three Gorges Reservoir area.

    Science.gov (United States)

    Wu, Lei; Long, Tian-Yu; Li, Chong-Ming

    2010-01-01

    Xiao-jiang, with a basin area of almost 5,276 km(2) and a length of 182.4 km, is located in the center of the Three Gorges Reservoir Area, and is the largest tributary of the central section in Three Gorges Reservoir Area, farmland accounts for a large proportion of Xiao-jiang watershed, and the hilly cropland of purple soil is much of the farmland of the watershed. After the second phase of water storage in the Three Gorges Reservoir, the majority of sub-rivers in the reservoir area experienced eutrophication phenomenon frequently, and non-point source (NPS) pollution has become an important source of pollution in Xiao-jiang Watershed. Because dissolved nitrogen and phosphorus non-point source pollution are related to surface runoff and interflow, using climatic, topographic and land cover data from the internet and research institutes, the Semi-Distributed Land-use Runoff Process (SLURP) hydrological model was introduced to simulate the complete hydrological cycle of the Xiao-jiang Watershed. Based on the SLURP distributed hydrological model, non-point source pollution annual output load models of land use and rural residents were respectively established. Therefore, using GIS technology, considering the losses of dissolved nitrogen and phosphorus in the course of transport, a dissolved non-point source pollution load dynamic model was established by the organic coupling of the SLURP hydrological model and land-use output model. Through the above dynamic model, the annual dissolved non-point source nitrogen and phosphorus pollution output as well as the load in different types were simulated and quantitatively estimated from 2001 to 2008, furthermore, the loads of Xiao-jiang Watershed were calculated and expressed by temporal and spatial distribution in the Three Gorges Reservoir Area. The simulation results show that: the temporal changes of dissolved nitrogen and phosphorus load in the watershed are close to the inter-annual changes of rainfall runoff, and the

  16. Time dependence of the field energy densities surrounding sources: Application to scalar mesons near point sources and to electromagnetic fields near molecules

    International Nuclear Information System (INIS)

    Persico, F.; Power, E.A.

    1987-01-01

    The time dependence of the dressing-undressing process, i.e., the acquiring or losing by a source of a boson field intensity and hence of a field energy density in its neighborhood, is considered by examining some simple soluble models. First, the loss of the virtual field is followed in time when a point source is suddenly decoupled from a neutral scalar meson field. Second, an initially bare point source acquires a virtual meson cloud as the coupling is switched on. The third example is that of an initially bare molecule interacting with the vacuum of the electromagnetic field to acquire a virtual photon cloud. In all three cases the dressing-undressing is shown to take place within an expanding sphere of radius r = ct centered at the source. At each point in space the energy density tends, for large times, to that of the ground state of the total system. Differences in the time dependence of the dressing between the massive scalar field and the massless electromagnetic field are discussed. The results are also briefly discussed in the light of Feinberg's ideas on the nature of half-dressed states in quantum field theory

  17. A TARGETED SEARCH FOR POINT SOURCES OF EeV NEUTRONS

    Energy Technology Data Exchange (ETDEWEB)

    Aab, A. [Universität Siegen, Siegen (Germany); Abreu, P.; Andringa, S. [Laboratório de Instrumentação e Física Experimental de Partículas-LIP and Instituto Superior Técnico-IST, Universidade de Lisboa-UL (Portugal); Aglietta, M. [Osservatorio Astrofisico di Torino (INAF), Università di Torino and Sezione INFN, Torino (Italy); Ahlers, M. [University of Wisconsin, Madison, WI (United States); Ahn, E. J. [Fermilab, Batavia, IL (United States); Al Samarai, I. [Institut de Physique Nucléaire d' Orsay (IPNO), Université Paris 11, CNRS-IN2P3, Orsay (France); Albuquerque, I. F. M. [Universidade de São Paulo, Instituto de Física, São Paulo, SP (Brazil); Allekotte, I. [Centro Atómico Bariloche and Instituto Balseiro (CNEA-UNCuyo-CONICET), San Carlos de Bariloche (Argentina); Allen, J. [New York University, New York, NY (United States); Allison, P. [Ohio State University, Columbus, OH (United States); Almela, A. [Universidad Tecnológica Nacional-Facultad Regional Buenos Aires, Buenos Aires (Argentina); Castillo, J. Alvarez [Universidad Nacional Autonoma de Mexico, Mexico, D. F. (Mexico); Alvarez-Muñiz, J. [Universidad de Santiago de Compostela (Spain); Batista, R. Alves [Universität Hamburg, Hamburg (Germany); Ambrosio, M.; Aramo, C. [Università di Napoli " Federico II" and Sezione INFN, Napoli (Italy); Aminaei, A. [IMAPP, Radboud University Nijmegen (Netherlands); Anchordoqui, L. [University of Wisconsin, Milwaukee, WI (United States); Arqueros, F. [Universidad Complutense de Madrid, Madrid (Spain); Collaboration: Pierre Auger Collaboration101; and others

    2014-07-10

    A flux of neutrons from an astrophysical source in the Galaxy can be detected in the Pierre Auger Observatory as an excess of cosmic-ray air showers arriving from the direction of the source. To avoid the statistical penalty for making many trials, classes of objects are tested in combinations as nine ''target sets'', in addition to the search for a neutron flux from the Galactic center or from the Galactic plane. Within a target set, each candidate source is weighted in proportion to its electromagnetic flux, its exposure to the Auger Observatory, and its flux attenuation factor due to neutron decay. These searches do not find evidence for a neutron flux from any class of candidate sources. Tabulated results give the combined p-value for each class, with and without the weights, and also the flux upper limit for the most significant candidate source within each class. These limits on fluxes of neutrons significantly constrain models of EeV proton emission from non-transient discrete sources in the Galaxy.

  18. A 24 μm point source catalog of the galactic plane from Spitzer/MIPSGAL

    International Nuclear Information System (INIS)

    Gutermuth, Robert A.; Heyer, Mark

    2015-01-01

    In this contribution, we describe the applied methods to construct a 24 μm based point source catalog derived from the image data of the MIPSGAL 24 μm Galactic Plane Survey and the corresponding data products. The high quality catalog product contains 933,818 sources, with a total of 1,353,228 in the full archive catalog. The source tables include positional and photometric information derived from the 24 μm images, source quality and confusion flags, and counterpart photometry from matched 2MASS, GLIMPSE, and WISE point sources. Completeness decay data cubes are constructed at 1′ angular resolution that describe the varying background levels over the MIPSGAL field and the ability to extract sources of a given magnitude from this background. The completeness decay cubes are included in the set of data products. We present the results of our efforts to verify the astrometric and photometric calibration of the catalog, and present several analyses of minor anomalies in these measurements to justify adopted mitigation strategies.

  19. A 24 μm Point Source Catalog of the Galactic Plane from Spitzer/MIPSGAL

    Science.gov (United States)

    Gutermuth, Robert A.; Heyer, Mark

    2015-02-01

    In this contribution, we describe the applied methods to construct a 24 μm based point source catalog derived from the image data of the MIPSGAL 24 μm Galactic Plane Survey and the corresponding data products. The high quality catalog product contains 933,818 sources, with a total of 1,353,228 in the full archive catalog. The source tables include positional and photometric information derived from the 24 μm images, source quality and confusion flags, and counterpart photometry from matched 2MASS, GLIMPSE, and WISE point sources. Completeness decay data cubes are constructed at 1‧ angular resolution that describe the varying background levels over the MIPSGAL field and the ability to extract sources of a given magnitude from this background. The completeness decay cubes are included in the set of data products. We present the results of our efforts to verify the astrometric and photometric calibration of the catalog, and present several analyses of minor anomalies in these measurements to justify adopted mitigation strategies.

  20. Searches for small-scale anisotropies from neutrino point sources with three years of IceCube data

    Science.gov (United States)

    Aartsen, M. G.; Ackermann, M.; Adams, J.; Aguilar, J. A.; Ahlers, M.; Ahrens, M.; Altmann, D.; Anderson, T.; Arguelles, C.; Arlen, T. C.; Auffenberg, J.; Bai, X.; Barwick, S. W.; Baum, V.; Beatty, J. J.; Becker Tjus, J.; Becker, K.-H.; BenZvi, S.; Berghaus, P.; Berley, D.; Bernardini, E.; Bernhard, A.; Besson, D. Z.; Binder, G.; Bindig, D.; Bissok, M.; Blaufuss, E.; Blumenthal, J.; Boersma, D. J.; Bohm, C.; Bos, F.; Bose, D.; Böser, S.; Botner, O.; Brayeur, L.; Bretz, H.-P.; Brown, A. M.; Casey, J.; Casier, M.; Cheung, E.; Chirkin, D.; Christov, A.; Christy, B.; Clark, K.; Classen, L.; Clevermann, F.; Coenders, S.; Cowen, D. F.; Cruz Silva, A. H.; Danninger, M.; Daughhetee, J.; Davis, J. C.; Day, M.; de André, J. P. A. M.; De Clercq, C.; De Ridder, S.; Desiati, P.; de Vries, K. D.; de With, M.; DeYoung, T.; Díaz-Vélez, J. C.; Dunkman, M.; Eagan, R.; Eberhardt, B.; Eichmann, B.; Eisch, J.; Euler, S.; Evenson, P. A.; Fadiran, O.; Fazely, A. R.; Fedynitch, A.; Feintzeig, J.; Felde, J.; Feusels, T.; Filimonov, K.; Finley, C.; Fischer-Wasels, T.; Flis, S.; Franckowiak, A.; Frantzen, K.; Fuchs, T.; Gaisser, T. K.; Gaior, R.; Gallagher, J.; Gerhardt, L.; Gier, D.; Gladstone, L.; Glüsenkamp, T.; Goldschmidt, A.; Golup, G.; Gonzalez, J. G.; Goodman, J. A.; Góra, D.; Grant, D.; Gretskov, P.; Groh, J. C.; Groß, A.; Ha, C.; Haack, C.; Haj Ismail, A.; Hallen, P.; Hallgren, A.; Halzen, F.; Hanson, K.; Hebecker, D.; Heereman, D.; Heinen, D.; Helbing, K.; Hellauer, R.; Hellwig, D.; Hickford, S.; Hill, G. C.; Hoffman, K. D.; Hoffmann, R.; Homeier, A.; Hoshina, K.; Huang, F.; Huelsnitz, W.; Hulth, P. O.; Hultqvist, K.; Hussain, S.; Ishihara, A.; Jacobi, E.; Jacobsen, J.; Jagielski, K.; Japaridze, G. S.; Jero, K.; Jlelati, O.; Jurkovic, M.; Kaminsky, B.; Kappes, A.; Karg, T.; Karle, A.; Kauer, M.; Kelley, J. L.; Kheirandish, A.; Kiryluk, J.; Kläs, J.; Klein, S. R.; Köhne, J.-H.; Kohnen, G.; Kolanoski, H.; Koob, A.; Köpke, L.; Kopper, C.; Kopper, S.; Koskinen, D. J.; Kowalski, M.; Kriesten, A.; Krings, K.; Kroll, G.; Kroll, M.; Kunnen, J.; Kurahashi, N.; Kuwabara, T.; Labare, M.; Larsen, D. T.; Larson, M. J.; Lesiak-Bzdak, M.; Leuermann, M.; Leute, J.; Lünemann, J.; Madsen, J.; Maggi, G.; Maruyama, R.; Mase, K.; Matis, H. S.; Maunu, R.; McNally, F.; Meagher, K.; Medici, M.; Meli, A.; Meures, T.; Miarecki, S.; Middell, E.; Middlemas, E.; Milke, N.; Miller, J.; Mohrmann, L.; Montaruli, T.; Morse, R.; Nahnhauer, R.; Naumann, U.; Niederhausen, H.; Nowicki, S. C.; Nygren, D. R.; Obertacke, A.; Odrowski, S.; Olivas, A.; Omairat, A.; O'Murchadha, A.; Palczewski, T.; Paul, L.; Penek, Ö.; Pepper, J. A.; Pérez de los Heros, C.; Pfendner, C.; Pieloth, D.; Pinat, E.; Posselt, J.; Price, P. B.; Przybylski, G. T.; Pütz, J.; Quinnan, M.; Rädel, L.; Rameez, M.; Rawlins, K.; Redl, P.; Rees, I.; Reimann, R.; Relich, M.; Resconi, E.; Rhode, W.; Richman, M.; Riedel, B.; Robertson, S.; Rodrigues, J. P.; Rongen, M.; Rott, C.; Ruhe, T.; Ruzybayev, B.; Ryckbosch, D.; Saba, S. M.; Sander, H.-G.; Sandroos, J.; Santander, M.; Sarkar, S.; Schatto, K.; Scheriau, F.; Schmidt, T.; Schmitz, M.; Schoenen, S.; Schöneberg, S.; Schönwald, A.; Schukraft, A.; Schulte, L.; Schulz, O.; Seckel, D.; Sestayo, Y.; Seunarine, S.; Shanidze, R.; Smith, M. W. E.; Soldin, D.; Spiczak, G. M.; Spiering, C.; Stamatikos, M.; Stanev, T.; Stanisha, N. A.; Stasik, A.; Stezelberger, T.; Stokstad, R. G.; Stößl, A.; Strahler, E. A.; Ström, R.; Strotjohann, N. L.; Sullivan, G. W.; Taavola, H.; Taboada, I.; Tamburro, A.; Tepe, A.; Ter-Antonyan, S.; Terliuk, A.; Tešić, G.; Tilav, S.; Toale, P. A.; Tobin, M. N.; Tosi, D.; Tselengidou, M.; Unger, E.; Usner, M.; Vallecorsa, S.; van Eijndhoven, N.; Vandenbroucke, J.; van Santen, J.; Vehring, M.; Voge, M.; Vraeghe, M.; Walck, C.; Wallraff, M.; Weaver, Ch.; Wellons, M.; Wendt, C.; Westerhoff, S.; Whelan, B. J.; Whitehorn, N.; Wichary, C.; Wiebe, K.; Wiebusch, C. H.; Williams, D. R.; Wissing, H.; Wolf, M.; Wood, T. R.; Woschnagg, K.; Xu, D. L.; Xu, X. W.; Yanez, J. P.; Yodh, G.; Yoshida, S.; Zarzhitsky, P.; Ziemann, J.; Zierke, S.; Zoll, M.

    2015-06-01

    Recently, IceCube found evidence for a diffuse signal of astrophysical neutrinos in an energy range of ∼ 60TeV to the PeV-scale [1]. The origin of those events, being a key to understanding the origin of cosmic rays, is still an unsolved question. So far, analyses have not succeeded to resolve the diffuse signal into point-like sources. Searches including a maximum-likelihood-ratio test, based on the reconstructed directions and energies of the detected down- and up-going neutrino candidates, were also performed on IceCube data leading to the exclusion of bright point sources. In this paper, we present two methods to search for faint neutrino point sources in three years of IceCube data, taken between 2008 and 2011. The first method is an autocorrelation test, applied separately to the northern and southern sky. The second method is a multipole analysis, which expands the measured data in the northern hemisphere into spherical harmonics and uses the resulting expansion coefficients to separate signal from background. With both methods, the results are consistent with the background expectation with a slightly more sparse spatial distribution, corresponding to an underfluctuation. Depending on the assumed number of sources, the resulting upper limit on the flux per source in the northern hemisphere for an E-2 energy spectrum ranges from ∼ 1.5 ·10-8 GeV/cm2 s-1, in the case of one assumed source, to ∼ 4 ·10-10 GeV/cm2 s-1, in the case of 3500 assumed sources.

  1. Sources of Caffeine in Diets of US Children and Adults: Trends by Beverage Type and Purchase Location

    Science.gov (United States)

    Drewnowski, Adam; Rehm, Colin D.

    2016-01-01

    New sources of caffeine, besides coffee and tea, have been introduced into the US food supply. Data on caffeine consumption age and purchase location can help guide public health policy. National Health and Nutrition Examination Surveys (NHANES) were used to estimate population-level caffeine intakes, using data from 24-h dietary recall. First, caffeine intakes by age-group and beverage type were estimated using the most recent 2011–2012 data (n = 7456). Second, fourteen years trends in caffeine consumption, overall and by beverage type, were evaluated for adults and children. Trend analyses were conducted by age groups. Last, trends in caffeine intakes by purchase location and beverage type were estimated. In 2011–2012, children aged four to eight years consumed the least caffeine (15 mg/day), and adults aged 51–70 years consumed the most (213 mg/day). The population mean (age ≥ four years) was 135 mg/day, driven largely by coffee (90 mg/day), tea (25 mg/day), and soda (21 mg/day). For the 14–19 years and 20–34 years age-groups, energy drinks contributed 6 mg/day (9.9%) and 5 mg/day (4.5%), respectively. The bulk of caffeine came from store-bought coffee and tea. Among both children and adults combined, caffeine intakes declined from 175 mg/day (1999–2000) to 142 mg/day (2011–2012), largely driven by a drop in caffeine from soda (41 mg/day to 21 mg/day). Store-bought coffee and tea remain principal drivers of caffeine intake in the US. Sodas and energy drinks make minor contributions to overall caffeine intakes. PMID:26978391

  2. Sources of Caffeine in Diets of US Children and Adults: Trends by Beverage Type and Purchase Location.

    Science.gov (United States)

    Drewnowski, Adam; Rehm, Colin D

    2016-03-10

    New sources of caffeine, besides coffee and tea, have been introduced into the US food supply. Data on caffeine consumption age and purchase location can help guide public health policy. National Health and Nutrition Examination Surveys (NHANES) were used to estimate population-level caffeine intakes, using data from 24-h dietary recall. First, caffeine intakes by age-group and beverage type were estimated using the most recent 2011-2012 data (n = 7456). Second, fourteen years trends in caffeine consumption, overall and by beverage type, were evaluated for adults and children. Trend analyses were conducted by age groups. Last, trends in caffeine intakes by purchase location and beverage type were estimated. In 2011-2012, children aged four to eight years consumed the least caffeine (15 mg/day), and adults aged 51-70 years consumed the most (213 mg/day). The population mean (age ≥ four years) was 135 mg/day, driven largely by coffee (90 mg/day), tea (25 mg/day), and soda (21 mg/day). For the 14-19 years and 20-34 years age-groups, energy drinks contributed 6 mg/day (9.9%) and 5 mg/day (4.5%), respectively. The bulk of caffeine came from store-bought coffee and tea. Among both children and adults combined, caffeine intakes declined from 175 mg/day (1999-2000) to 142 mg/day (2011-2012), largely driven by a drop in caffeine from soda (41 mg/day to 21 mg/day). Store-bought coffee and tea remain principal drivers of caffeine intake in the US. Sodas and energy drinks make minor contributions to overall caffeine intakes.

  3. Sources of Caffeine in Diets of US Children and Adults: Trends by Beverage Type and Purchase Location

    Directory of Open Access Journals (Sweden)

    Adam Drewnowski

    2016-03-01

    Full Text Available New sources of caffeine, besides coffee and tea, have been introduced into the US food supply. Data on caffeine consumption age and purchase location can help guide public health policy. National Health and Nutrition Examination Surveys (NHANES were used to estimate population-level caffeine intakes, using data from 24-h dietary recall. First, caffeine intakes by age-group and beverage type were estimated using the most recent 2011–2012 data (n = 7456. Second, fourteen years trends in caffeine consumption, overall and by beverage type, were evaluated for adults and children. Trend analyses were conducted by age groups. Last, trends in caffeine intakes by purchase location and beverage type were estimated. In 2011–2012, children aged four to eight years consumed the least caffeine (15 mg/day, and adults aged 51–70 years consumed the most (213 mg/day. The population mean (age ≥ four years was 135 mg/day, driven largely by coffee (90 mg/day, tea (25 mg/day, and soda (21 mg/day. For the 14–19 years and 20–34 years age-groups, energy drinks contributed 6 mg/day (9.9% and 5 mg/day (4.5%, respectively. The bulk of caffeine came from store-bought coffee and tea. Among both children and adults combined, caffeine intakes declined from 175 mg/day (1999–2000 to 142 mg/day (2011–2012, largely driven by a drop in caffeine from soda (41 mg/day to 21 mg/day. Store-bought coffee and tea remain principal drivers of caffeine intake in the US. Sodas and energy drinks make minor contributions to overall caffeine intakes.

  4. Joint inversion of seismic velocities and source location without rays using the truncated Newton and the adjoint-state method

    Science.gov (United States)

    Virieux, J.; Bretaudeau, F.; Metivier, L.; Brossier, R.

    2013-12-01

    Simultaneous inversion of seismic velocities and source parameters have been a long standing challenge in seismology since the first attempts to mitigate trade-off between very different parameters influencing travel-times (Spencer and Gubbins 1980, Pavlis and Booker 1980) since the early development in the 1970s (Aki et al 1976, Aki and Lee 1976, Crosson 1976). There is a strong trade-off between earthquake source positions, initial times and velocities during the tomographic inversion: mitigating these trade-offs is usually carried empirically (Lemeur et al 1997). This procedure is not optimal and may lead to errors in the velocity reconstruction as well as in the source localization. For a better simultaneous estimation of such multi-parametric reconstruction problem, one may take benefit of improved local optimization such as full Newton method where the Hessian influence helps balancing between different physical parameter quantities and improving the coverage at the point of reconstruction. Unfortunately, the computation of the full Hessian operator is not easily computed in large models and with large datasets. Truncated Newton (TCN) is an alternative optimization approach (Métivier et al. 2012) that allows resolution of the normal equation H Δm = - g using a matrix-free conjugate gradient algorithm. It only requires to be able to compute the gradient of the misfit function and Hessian-vector products. Traveltime maps can be computed in the whole domain by numerical modeling (Vidale 1998, Zhao 2004). The gradient and the Hessian-vector products for velocities can be computed without ray-tracing using 1st and 2nd order adjoint-state methods for the cost of 1 and 2 additional modeling step (Plessix 2006, Métivier et al. 2012). Reciprocity allows to compute accurately the gradient and the full Hessian for each coordinates of the sources and for their initial times. Then the resolution of the problem is done through two nested loops. The model update Δm is

  5. An Analysis of Air Pollution in Makkah - a View Point of Source Identification

    Directory of Open Access Journals (Sweden)

    Turki M. Habeebullah

    2013-07-01

    Full Text Available Makkah is one of the busiest cities in Saudi Arabia and remains busy all year around, especially during the season of Hajj and the month of Ramadan when millions of people visit this city. This emphasizes the importance of clean air and of understanding the sources of various air pollutants, which is vital for the management and advanced modeling of air pollution. This study intends to identify the major sources of air pollutants in Makkah, near the Holy Mosque (Al-Haram using a graphical approach. Air pollutants considered in this study are nitrogen oxides (NOx, nitrogen dioxide (NO2, nitric oxide (NO, carbon monoxide (CO, sulphur dioxide (SO2, ozone (O3 and particulate matter with aero-dynamic diameter of 10 um or less (PM10. Polar plots, time variation plots and correlation analysis are used to analyse the data and identify the major sources of emissions. Most of the pollutants demonstrate high concentrations during the morning traffic peak hours, suggesting road traffic as the main source of emission. The main sources of pollutant emissions identified in Makkahwere road traffic, re-suspended and windblown dust and sand particles. Further investigation on detailedsource apportionment is required, which is part of the ongoing project.

  6. 77 FR 112 - Effluent Limitations Guidelines and Standards for the Construction and Development Point Source...

    Science.gov (United States)

    2012-01-03

    .../L of TSS while the peak concentration discharged from the passive sand filter \\2\\ after the basin... two-day period. Effluent turbidity from one passive sand filter during this storm ranged from approximately 50 to 375 NTU, with 20 of the 24 data points below 200 NTU. For a second passive sand filter...

  7. Crowd-sourced BMS point matching and metadata maintenance with Babel

    DEFF Research Database (Denmark)

    Fürst, Jonathan; Chen, Kaifei; Katz, Randy H.

    2016-01-01

    , occupants provide physical and digital input in form of actuations (e.g., the turning on/off a light) and readings (e.g., reading room temperature of a thermostat) to Babel. Babel then matches this input to digital points in the BMS based on value equality. We have implemented a prototype of our system...

  8. SREM - WRS system module number 3348 for calculating the removal flux due to point, line or disc sources

    International Nuclear Information System (INIS)

    Grimstone, M.J.

    1978-06-01

    The WRS Modular Programming System has been developed as a means by which programmes may be more efficiently constructed, maintained and modified. In this system a module is a self-contained unit typically composed of one or more Fortran routines, and a programme is constructed from a number of such modules. This report describes one WRS module, the function of which is to calculate the uncollided flux and first-collision source from a disc source in a slab geometry system, a line source at the centre of a cylindrical system or a point source at the centre of a spherical system. The information given in this manual is of use both to the programmer wishing to incorporate the module in a programme, and to the user of such a programme. (author)

  9. A THEORETICAL ANALYSIS OF KEY POINTS WHEN CHOOSING OPEN SOURCE ERP SYSTEMS

    Directory of Open Access Journals (Sweden)

    Fernando Gustavo Dos Santos Gripe

    2011-08-01

    Full Text Available The present work is aimed at presenting a theoretical analysis of the main features of Open Source ERP systems, herein identified as success technical factors, in order to contribute to the establishment of parameters to be used in decision-making processes when choosing a system which fulfills the organization´s needs. Initially, the life cycle of ERP systems is contextualized, highlighting the features of Open Source ERP systems. As a result, it was verified that, when carefully analyzed, these systems need further attention regarding issues of project continuity and maturity, structure, transparency, updating frequency, and support, all of which are inherent to the reality of this type of software. Nevertheless, advantages were observed in what concerns flexibility, costs, and non-discontinuity as benefits. The main goal is to broaden the discussion about the adoption of Open Source ERP systems.

  10. A Credibility-Based Chance-Constrained Transfer Point Location Model for the Relief Logistics Design (Case Study: Earthquake Disaster on Region 1 of Tehran City

    Directory of Open Access Journals (Sweden)

    Ahmad Mohamadi

    2015-02-01

    Full Text Available Occurrence of natural disaster inflicts irreparable injuries and symptoms on humans. In such conditions, affected people are waiting for medical services and relief commodities. Thus, quick reaction of medical services and relief commodities supply play important roles in improving natural disaster management. In this paper, a multi-objective non-linear credibility-based fuzzy mathematical programming model under uncertainty conditions is presented, which considers two vital needs in disaster time including medical services and relief commodities through location of hospitals, transfer points, and location routing of relief depots. The proposed model approaches reality by considering time, cost, failures probability in routes, and parameters uncertainty. The problem is first linearized and then global criterion method is applied for solving the multi objective model. Moreover, to illustrate model efficiency, a case study is performed on region 1 of Tehran city for earthquake disaster. Results demonstrate that if Decision-makers want to meet uncertainty with lowered risk, they have to choose a high minimum constraint feasibility degree even though the objective function will be worse.

  11. [Spatial discharge characteristics and total load control of non-point source pollutants based on the catchment scale].

    Science.gov (United States)

    Wang, Xia-Hui; Lu, Jun; Zhang, Qing-Zhong; Wang, Bo; Yao, Rui-Hua; Zhang, Hui-Yuan; Huang, Feng

    2011-09-01

    Agricultural non-point source pollution is one of the major causes of water quality deterioration. Based on the analysis of the spatial discharge characteristics and intensity of major pollutants from the agricultural pollution source, the establishment of spatial management subzones for controlling agricultural non-point pollution and a design of a plan for total load control of pollutants from each subzone is an important way to improve the efficiency of control measures. In this paper the Four Lake basin in Hubei Province is adopted as the research case region and a systematic research of the control countermeasures of agricultural non-point pollution based on the catchment scale is carried out. The results shows that in the Four Lake basin, the COD, total nitrogen, total phosphorus and ammonia nitrogen load of the water environment are mainly caused by agricultural non-point pollution. These four kinds of non-point source pollutants respectively account for 67.6%, 82.2%, 84.7% and 50.9% of the total pollutant discharge amount in the basin. The analysis of the spatial discharge characteristics of non-point source pollutants in the Four Lake basin shows that the major contributor source regions of non-point source pollutant in the basin are the four counties, including Honghu, Jianli, Qianjiang and Shayang where the aquatic and livestock production are relatively developed. According to the spatial discharge characteristics of the pollutants and the evaluation of the discharge intensity of pollutants, the Four Lake basin is divided into three agricultural non-point pollution management subzones, which including Changhu upstream aquatic and livestock production pollution control subzone, Four-lake trunk canal rural non-point source pollution control subzone and Honghu aquatic production pollution control subzone. Specific pollution control measures are put forward for each subzone. With a comprehensive consideration of the water quality amelioration and the

  12. Connecting smoke plumes to sources using Hazard Mapping System (HMS) smoke and fire location data over North America

    Science.gov (United States)

    Brey, Steven J.; Ruminski, Mark; Atwood, Samuel A.; Fischer, Emily V.

    2018-02-01

    Fires represent an air quality challenge because they are large, dynamic and transient sources of particulate matter and ozone precursors. Transported smoke can deteriorate air quality over large regions. Fire severity and frequency are likely to increase in the future, exacerbating an existing problem. Using the National Environmental Satellite, Data, and Information Service (NESDIS) Hazard Mapping System (HMS) smoke data for North America for the period 2007 to 2014, we examine a subset of fires that are confirmed to have produced sufficient smoke to warrant the initiation of a U.S. National Weather Service smoke forecast. We find that gridded HMS-analyzed fires are well correlated (r = 0.84) with emissions from the Global Fire Emissions Inventory Database 4s (GFED4s). We define a new metric, smoke hours, by linking observed smoke plumes to active fires using ensembles of forward trajectories. This work shows that the Southwest, Northwest, and Northwest Territories initiate the most air quality forecasts and produce more smoke than any other North American region by measure of the number of HYSPLIT points analyzed, the duration of those HYSPLIT points, and the total number of smoke hours produced. The average number of days with smoke plumes overhead is largest over the north-central United States. Only Alaska, the Northwest, the Southwest, and Southeast United States regions produce the majority of smoke plumes observed over their own borders. This work moves a new dataset from a daily operational setting to a research context, and it demonstrates how changes to the frequency or intensity of fires in the western United States could impact other regions.

  13. Connecting smoke plumes to sources using Hazard Mapping System (HMS smoke and fire location data over North America

    Directory of Open Access Journals (Sweden)

    S. J. Brey

    2018-02-01

    Full Text Available Fires represent an air quality challenge because they are large, dynamic and transient sources of particulate matter and ozone precursors. Transported smoke can deteriorate air quality over large regions. Fire severity and frequency are likely to increase in the future, exacerbating an existing problem. Using the National Environmental Satellite, Data, and Information Service (NESDIS Hazard Mapping System (HMS smoke data for North America for the period 2007 to 2014, we examine a subset of fires that are confirmed to have produced sufficient smoke to warrant the initiation of a U.S. National Weather Service smoke forecast. We find that gridded HMS-analyzed fires are well correlated (r =  0.84 with emissions from the Global Fire Emissions Inventory Database 4s (GFED4s. We define a new metric, smoke hours, by linking observed smoke plumes to active fires using ensembles of forward trajectories. This work shows that the Southwest, Northwest, and Northwest Territories initiate the most air quality forecasts and produce more smoke than any other North American region by measure of the number of HYSPLIT points analyzed, the duration of those HYSPLIT points, and the total number of smoke hours produced. The average number of days with smoke plumes overhead is largest over the north-central United States. Only Alaska, the Northwest, the Southwest, and Southeast United States regions produce the majority of smoke plumes observed over their own borders. This work moves a new dataset from a daily operational setting to a research context, and it demonstrates how changes to the frequency or intensity of fires in the western United States could impact other regions.

  14. First Search for Point Sources of High-Energy Cosmic Neutrinos with the ANTARES Neutrino Telescope

    NARCIS (Netherlands)

    Adrian-Martinez, S.; Aguilar, J.A.; Al Samarai, I.; Albert, A.; Andre, M.; Anghinolfi, M.; Anton, G.; Anvar, S.; Ardid, M.; Jesus, A.C.A.; Astraatmadja, T.; Aubert, J.J.; Baret, B.; Basa, S.; Bertin, V.; Biagi, S.; Bigi, A.; Bigongiari, C.; Bogazzi, C.; Bou-Cabo, M.; Bouhou, B.; Bouwhuis, M.C.; Brunner, J.; Busto, J.; Camarena, F.; Capone, A.; Carloganu, C.; Carminati, G.; Carr, J.; Cecchini, S.; Charif, Z.; Charvis, P.; Chiarusi, T.; Circella, M.; Coniglione, R.; Costantini, H.; Coyle, P.; Curtil, C.; Decowski, M.P.; Dekeyser, I.; Deschamps, A.; Distefano, C.; Donzaud, C.; Dornic, D.; Dorosti, Q.; Drouhin, D.; Eberl, T.; Emanuele, U.; Enzenhofer, A.; Ernenwein, J.P.; Escoffier, S.; Fermani, P.; Ferri, M.; Flaminio, V.; Folger, F.; Fritsch, U.; Fuda, J.L.; Galata, S.; Gay, P.; Giacomelli, G.; Giordano, V.; Gomez-Gonzalez, J.P.; Graf, K.; Guillard, G.; Halladjian, G.; Hallewell, G.; van Haren, H.; Hartman, J.; Heijboer, A.J.; Hello, Y.; Hernandez-Rey, J.J.; Herold, B.; Hossl, J.; Hsu, C.C.; De Jong, M.; Kadler, M.; Kalekin, O.; Kappes, A.; Katz, U.; Kavatsyuk, O.; Kooijman, P.; Kopper, C.; Kouchner, A.; Kreykenbohm, I.; Kulikovskiy, V.; Lahmann, R.; Lamare, P.; Larosa, G.; Lattuada, D.; Lefevre, D.; Lim, G.; Lo Presti, D.; Loehner, H.; Loucatos, S.; Mangano, S.; Marcelin, M.; Margiotta, A.; Martinez-Mora, J.A.; Meli, A.; Montaruli, T.; Moscoso, L.; Motz, H.; Neff, M.; Nezri, E.; Palioselitis, D.; Pavalas, G.E.; Payet, K.; Payre, P.; Petrovic, J.; Piattelli, P.; Picot-Clemente, N.; Popa, V.; Pradier, T.; Presani, E.; Racca, C.; Reed, C.; Richardt, C.; Richter, R.; Riviere, C.; Robert, A.; Roensch, K.; Rostovtsev, A.; Ruiz-Rivas, J.; Rujoiu, M.; Russo, G.V.; Salesa, F.; Samtleben, D.F.E.; Sapienza, P.; Schock, F.; Schuller, J.P.; Schussler, F.; Seitz, T.; Shanidze, R.; Simeone, F.; Spies, A.; Spurio, M.; Steijger, J.J.M.; Stolarczyk, T.; Sanchez-Losa, A.; Taiuti, M.; Tamburini, C.; Toscano, S.; Vallage, B.; Van Elewyck, V.; Vannoni, G.; Vecchi, M.; Vernin, P.; Wagner, S.; Wijnker, G.; Wilms, J.; de Wolf, E.; Yepes, H.; Zaborov, D.; Zornoza, J.D.; Zuniga, J.

    2011-01-01

    Results are presented of a search for cosmic sources of high-energy neutrinos with the ANTARES neutrino telescope. The data were collected during 2007 and 2008 using detector configurations containing between 5 and 12 detection lines. The integrated live time of the analyzed data is 304 days. Muon

  15. Preliminary study on using rare earth elements to trace non-point source phosphorous loss

    Science.gov (United States)

    The environmental fate of phosphorus (P) is of concern as P is a primary cause of freshwater eutrophication. Rare earth elements (REEs) have been successfully used in the analysis of soil erosion and pollutant sources, as well as in the analysis of mineral genesis. To better understand the potential...

  16. Improving sourcing decisions in NPD projects: Monetary quantification of points of difference

    NARCIS (Netherlands)

    Wouters, Marc; Anderson, James C.; Narus, James A.; Wynstra, Finn

    2009-01-01

    During new product development (NPD), firms make critical design and sourcing decisions that determine the new product's cost, performance, competitive position, and profitability. The purchase price of materials and components for the new product provides only part of the picture for design and

  17. The Small Area Health Statistics Unit: a national facility for investigating health around point sources of environmental pollution in the United Kingdom.

    Science.gov (United States)

    Elliott, P; Westlake, A J; Hills, M; Kleinschmidt, I; Rodrigues, L; McGale, P; Marshall, K; Rose, G

    1992-01-01

    STUDY OBJECTIVE--The Small Area Health Statistics Unit (SAHSU) was established at the London School of Hygiene and Tropical Medicine in response to a recommendation of the enquiry into the increased incidence of childhood leukaemia near Sellafield, the nuclear reprocessing plant in West Cumbria. The aim of this paper was to describe the Unit's methods for the investigation of health around point sources of environmental pollution in the United Kingdom. DESIGN--Routine data currently including deaths and cancer registrations are held in a large national database which uses a post code based retrieval system to locate cases geographically and link them to the underlying census enumeration districts, and hence to their populations at risk. Main outcome measures were comparison of observed/expected ratios (based on national rates) within bands delineated by concentric circles around point sources of environmental pollution located anywhere in Britain. MAIN RESULTS--The system is illustrated by a study of mortality from mesothelioma and asbestosis near the Plymouth naval dockyards during 1981-87. Within a 3 km radius of the docks the mortality rate for mesothelioma was higher than the national rate by a factor of 8.4, and that for asbestosis was higher by a factor of 13.6. CONCLUSIONS--SAHSU is a new national facility which is rapidly able to provide rates of mortality and cancer incidence for arbitrary circles drawn around any point in Britain. The example around Plymouth of mesothelioma and asbestosis demonstrates the ability of the system to detect an unusual excess of disease in a small locality, although in this case the findings are likely to be related to occupational rather than environmental exposure. PMID:1431704

  18. A Spatial and Temporal Assessment of Non-Point Groundwater Pollution Sources, Tutuila Island, American Samoa

    Science.gov (United States)

    Shuler, C. K.; El-Kadi, A. I.; Dulaiova, H.; Glenn, C. R.; Fackrell, J.

    2015-12-01

    The quality of municipal groundwater supplies on Tutuila, the main island in American Samoa, is currently in question. A high vulnerability for contamination from surface activities has been recognized, and there exists a strong need to clearly identify anthropogenic sources of pollution and quantify their influence on the aquifer. This study examines spatial relationships and time series measurements of nutrients and other tracers to identify predominant pollution sources and determine the water quality impacts of the island's diverse land uses. Elevated groundwater nitrate concentrations are correlated with areas of human development, however, the mixture of residential and agricultural land use in this unique village based agrarian setting makes specific source identification difficult using traditional geospatial analysis. Spatial variation in anthropogenic impact was assessed by linking NO3- concentrations and δ15N(NO3) from an extensive groundwater survey to land-use types within well capture zones and groundwater flow-paths developed with MODFLOW, a numerical groundwater model. Land use types were obtained from high-resolution GIS data and compared to water quality results with multiple-regression analysis to quantify the impact that different land uses have on water quality. In addition, historical water quality data and new analyses of δD and δ18O in precipitation, groundwater, and mountain-front recharge waters were used to constrain the sources and mechanisms of contamination. Our analyses indicate that groundwater nutrient levels on Tutuila are controlled primarily by residential, not agricultural activity. Also a lack of temporal variation suggests that episodic pollution events are limited to individual water sources as opposed to the entire aquifer. These results are not only valuable for water quality management on Tutuila, but also provide insight into the sustainability of groundwater supplies on other islands with similar hydrogeology and land

  19. Correlation Wave-Front Sensing Algorithms for Shack-Hartmann-Based Adaptive Optics using a Point Source

    International Nuclear Information System (INIS)

    Poynee, L A

    2003-01-01

    Shack-Hartmann based Adaptive Optics system with a point-source reference normally use a wave-front sensing algorithm that estimates the centroid (center of mass) of the point-source image 'spot' to determine the wave-front slope. The centroiding algorithm suffers for several weaknesses. For a small number of pixels, the algorithm gain is dependent on spot size. The use of many pixels on the detector leads to significant propagation of read noise. Finally, background light or spot halo aberrations can skew results. In this paper an alternative algorithm that suffers from none of these problems is proposed: correlation of the spot with a ideal reference spot. The correlation method is derived and a theoretical analysis evaluates its performance in comparison with centroiding. Both simulation and data from real AO systems are used to illustrate the results. The correlation algorithm is more robust than centroiding, but requires more computation

  20. Impacts by point and diffuse micropollutant sources on the stream water quality at catchment scale

    DEFF Research Database (Denmark)

    Petersen, Mette Fjendbo; Eriksson, Eva; Binning, Philip John

    2012-01-01

    pollution sources were identified including a pharmaceutical factory site with a contaminated old drainage ditch, two waste deposits, a wastewater treatment plant, overflow structures, fish farms, industrial discharges and diffuse agricultural and urban sources. Six water samples were collected along...... impacts by releases of organic matter and nutrients were found after the fish farms and the waste water treatment plant. Nickel was found at concentrations 5.8 – 8.8 g/l. Nine pesticides and metabolites of both agricultural and urban use were detected along the stream; among these were the two most...... at the pharmaceutical factory site, the drainage ditch and the waste deposits is similar in composition containing among others sulfonamides and chlorinated solvents (including vinyl chloride). Vinyl chloride concentrations surpassed Danish stream water quality criteria with a factor 10. The largest chemical impact...

  1. First Search for Point Sources of High-energy Cosmic Neutrinos with the ANTARES Neutrino Telescope

    Science.gov (United States)

    Adrián-Martínez, S.; Aguilar, J. A.; Samarai, I. Al; Albert, A.; André, M.; Anghinolfi, M.; Anton, G.; Anvar, S.; Ardid, M.; Assis Jesus, A. C.; Astraatmadja, T.; Aubert, J.-J.; Baret, B.; Basa, S.; Bertin, V.; Biagi, S.; Bigi, A.; Bigongiari, C.; Bogazzi, C.; Bou-Cabo, M.; Bouhou, B.; Bouwhuis, M. C.; Brunner, J.; Busto, J.; Camarena, F.; Capone, A.; Cârloganu, C.; Carminati, G.; Carr, J.; Cecchini, S.; Charif, Z.; Charvis, Ph.; Chiarusi, T.; Circella, M.; Coniglione, R.; Costantini, H.; Coyle, P.; Curtil, C.; Decowski, M. P.; Dekeyser, I.; Deschamps, A.; Distefano, C.; Donzaud, C.; Dornic, D.; Dorosti, Q.; Drouhin, D.; Eberl, T.; Emanuele, U.; Enzenhöfer, A.; Ernenwein, J.-P.; Escoffier, S.; Fermani, P.; Ferri, M.; Flaminio, V.; Folger, F.; Fritsch, U.; Fuda, J.-L.; Galatà, S.; Gay, P.; Giacomelli, G.; Giordano, V.; Gómez-González, J. P.; Graf, K.; Guillard, G.; Halladjian, G.; Hallewell, G.; van Haren, H.; Hartman, J.; Heijboer, A. J.; Hello, Y.; Hernández-Rey, J. J.; Herold, B.; Hößl, J.; Hsu, C. C.; de Jong, M.; Kadler, M.; Kalekin, O.; Kappes, A.; Katz, U.; Kavatsyuk, O.; Kooijman, P.; Kopper, C.; Kouchner, A.; Kreykenbohm, I.; Kulikovskiy, V.; Lahmann, R.; Lamare, P.; Larosa, G.; Lattuada, D.; Lefèvre, D.; Lim, G.; Lo Presti, D.; Loehner, H.; Loucatos, S.; Mangano, S.; Marcelin, M.; Margiotta, A.; Martínez-Mora, J. A.; Meli, A.; Montaruli, T.; Moscoso, L.; Motz, H.; Neff, M.; Nezri, E.; Palioselitis, D.; Păvălaş, G. E.; Payet, K.; Payre, P.; Petrovic, J.; Piattelli, P.; Picot-Clemente, N.; Popa, V.; Pradier, T.; Presani, E.; Racca, C.; Reed, C.; Richardt, C.; Richter, R.; Rivière, C.; Robert, A.; Roensch, K.; Rostovtsev, A.; Ruiz-Rivas, J.; Rujoiu, M.; Russo, G. V.; Salesa, F.; Samtleben, D. F. E.; Sapienza, P.; Schöck, F.; Schuller, J.-P.; Schüssler, F.; Seitz, T.; Shanidze, R.; Simeone, F.; Spies, A.; Spurio, M.; Steijger, J. J. M.; Stolarczyk, Th.; Sánchez-Losa, A.; Taiuti, M.; Tamburini, C.; Toscano, S.; Vallage, B.; Van Elewyck, V.; Vannoni, G.; Vecchi, M.; Vernin, P.; Wagner, S.; Wijnker, G.; Wilms, J.; de Wolf, E.; Yepes, H.; Zaborov, D.; Zornoza, J. D.; Zúñiga, J.

    2011-12-01

    Results are presented of a search for cosmic sources of high-energy neutrinos with the ANTARES neutrino telescope. The data were collected during 2007 and 2008 using detector configurations containing between 5 and 12 detection lines. The integrated live time of the analyzed data is 304 days. Muon tracks are reconstructed using a likelihood-based algorithm. Studies of the detector timing indicate a median angular resolution of 0.5 ± 0.1 deg. The neutrino flux sensitivity is 7.5 × 10-8(E ν/ GeV)-2 GeV-1 s-1 cm-2 for the part of the sky that is always visible (δ < -48 deg), which is better than limits obtained by previous experiments. No cosmic neutrino sources have been observed. We dedicate this Letter to the memory of our colleague and friend Luciano Moscoso, who passed away during the preparation of this Letter.

  2. Study The Validity of The Direct Mathematical Method For Calculation The Total Efficiency Using Point And Disk Sources

    International Nuclear Information System (INIS)

    Hagag, O.M.; Nafee, S.S.; Naeem, M.A.; El Khatib, A.M.

    2011-01-01

    The direct mathematical method has been developed for calculating the total efficiency of many cylindrical gamma detectors, especially HPGe and NaI detector. Different source geometries are considered (point and disk). Further into account is taken of gamma attenuation from detector window or any interfacing absorbing layer. Results are compared with published experimental data to study the validity of the direct mathematical method to calculate total efficiency for any gamma detector size.

  3. Fast and Reliable Locating of Points with the Maximum Value of Total Electromagnetic Field Using a Modern Experimental Method for Radio Coverage in Urban Environment

    Directory of Open Access Journals (Sweden)

    Petar S. Medjedovic

    2014-01-01

    Full Text Available This research has been performed within the project “prediction, measurement, and analysis of composite electromagnetic field of artificial radiation sources,” funded by the Ministry of Science and Technology of the Republic of Srpska, Bosnia and Herzegovina. The ultimate goal of the project is the installation of a monitoring network for continuous measurement and recording of nonionizing electromagnetic (EM radiation levels in the wider area of Banja Luka city centre covering about 10 km2. For this reason it was necessary to make an optimal choice from a dozen of measurement points with the maximum value levels of total EM field. It was a difficult task, because in this case, with the resolution of 5m × 5m, approximately 400,000 points should be examined. Therefore, the pedestrian zones, areas, and routes with significantly smaller surfaces but with the largest flow of people have been examined, so the time required for their mapping with values of total EM field has been reduced to a more realistic framework. In this paper, in the volume allowed by the defined criteria, a fast and reliable experimental method has been described, which has been examined at one of the studied areas in the named project, with surface of 0.008 km2.

  4. Tracking an oil slick from multiple natural sources, Coal Oil Point, California

    Energy Technology Data Exchange (ETDEWEB)

    Leifer, Ira [Marine Sciences Institute, University of California, Santa Barbara, CA 93106 (United States); Luyendyk, Bruce [Department of Geological Sciences, University of California, Santa Barbara, CA 93106 (United States); Broderick, Kris [Exxon/Mobil Exploration Company, 13401 N. Freeway, Houston, TX 77060 (United States)

    2006-06-15

    Oil slicks on the ocean surface emitted from natural marine hydrocarbon seeps offshore from Coal Oil Point in the Santa Barbara Channel, California were tracked and sampled over a 2-h period. The objectives were to characterize the seep oil and to track its composition over time using a new sampling device, a catamaran drum sampler (CATDRUMS). The sampler was designed and developed at UCSB. Chromatograms showed that oil originating from an informally named, very active seep area, Shane Seep, primarily evolved during the first hour due to mixing with oil originating from a convergence zone slick surrounding Shane Seep. (author)

  5. Search for atmospheric muon-neutrinos and extraterrestric neutrino point sources in the 1997 AMANDA-B10 data

    International Nuclear Information System (INIS)

    Biron von Curland, A.

    2002-07-01

    The young field of high energy neutrino astronomy can be motivated by the search for the origin of the charged cosmic rays. Large astrophysical objects like AGNs or supernova remnants are candidates to accelerate hadrons which then can interact to eventually produce high energy neutrinos. Neutrino-induced muons can be detected via their emission of Cherenkov light in large neutrino telescopes like AMANDA. More than 10 9 atmospheric muon events and approximately 5000 atmospheric neutrino events were registered by AMANDA-B10 in 1997. Out of these, 223 atmospheric neutrino candidate events have been extracted. This data set contains approximately 15 background events. It allows to confirm the expected sensitivity of the detector towards neutrino events. A second set containing 369 (approximately 270 atmospheric neutrino events and 100 atmospheric muon events) was used to search for extraterrestrial neutrino point sources. Neither a binned search, nor a cluster search, nor a search for preselected sources gave indications for the existence of a strong neutrino point source. Based on this result, flux limits were derived. Assuming E ν -2 spectra, typical flux limits for selected sources of the order of Φ μ limit ∝ 10 -14 cm -2 s -1 for muons and Φ ν limit ∝ 10 -7 cm -2 s -1 for neutrinos have been obtained. (orig.)

  6. Energy demand modelling: pointing out alternative energy sources. The example of industry in OECD countries

    International Nuclear Information System (INIS)

    Renou, P.

    1992-01-01

    This thesis studies energy demand and alternative energy sources in OECD countries. In the first part, the principle models usually used for energy demand modelling. In the second part, the author studies the flexible functional forms (translog, generalized Leontief, generalized quadratic, Fourier) to obtain an estimation of the production function. In the third part, several examples are given, chosen in seven countries (Usa, Japan, Federal Republic of Germany, France, United Kingdom, Italy, Canada). Energy systems analysis in these countries, can help to choose models and gives informations on alternative energies. 246 refs., 24 figs., 27 tabs

  7. PSD Applicability Determination for Multiple Owner/Operator Point Sources Within a Single Facility

    Science.gov (United States)

    This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  8. Shielding design for a Cs-137 rod-type standard point source for well chamber constancy checks.

    Science.gov (United States)

    Sabet, Mahsheed; Cryer, David; Waterhouse, David

    2016-12-01

    Well type chambers are used for radioactive source calibrations in brachytherapy, but do not provide radiation shielding. Routine constancy checks on a well chamber are required between periodic secondary standard laboratory calibrations to ensure consistent device performance, and ultimately to ensure accurate patient dose delivery. In this work, a method is described to provide suitable shielding for a Cs-137 rod-type point source to enable use for constancy checks. A novel plunger-type shielded housing was designed and constructed for the Cs-137 source that when combined with a suitably shielded well-chamber container minimised user exposure during constancy checks. The designed shielding proved effective, and a constancy test routine was established and used for the past 16 months. The well chamber showed consistent performance (0.12 ± 0.18 % from the baseline) and no increased exposure was reported on users' radiation badges.

  9. Investigating the effects of point source and nonpoint source pollution on the water quality of the East River (Dongjiang) in South China

    Science.gov (United States)

    Wu, Yiping; Chen, Ji

    2013-01-01

    Understanding the physical processes of point source (PS) and nonpoint source (NPS) pollution is critical to evaluate river water quality and identify major pollutant sources in a watershed. In this study, we used the physically-based hydrological/water quality model, Soil and Water Assessment Tool, to investigate the influence of PS and NPS pollution on the water quality of the East River (Dongjiang in Chinese) in southern China. Our results indicate that NPS pollution was the dominant contribution (>94%) to nutrient loads except for mineral phosphorus (50%). A comprehensive Water Quality Index (WQI) computed using eight key water quality variables demonstrates that water quality is better upstream than downstream despite the higher level of ammonium nitrogen found in upstream waters. Also, the temporal (seasonal) and spatial distributions of nutrient loads clearly indicate the critical time period (from late dry season to early wet season) and pollution source areas within the basin (middle and downstream agricultural lands), which resource managers can use to accomplish substantial reduction of NPS pollutant loadings. Overall, this study helps our understanding of the relationship between human activities and pollutant loads and further contributes to decision support for local watershed managers to protect water quality in this region. In particular, the methods presented such as integrating WQI with watershed modeling and identifying the critical time period and pollutions source areas can be valuable for other researchers worldwide.

  10. Electronic equilibrium as a function of depth in tissue from cobalt-60 point source exposures

    International Nuclear Information System (INIS)

    Myrick, J.A.

    1994-08-01

    The Nuclear Regulatory Commission has set the basic criteria for assessing skin dose stemming from hot particle contaminations. Compliance with 10 CFR 20.101 requires that exposure to the skin be evaluated over a 1 cm 2 area at a depth of 0.007 cm. Skin exposure can arise from both the beta and gamma components of radioactive particles and gamma radiation can contribute significantly to skin doses. The gamma component of dose increases dramatically when layers of protective clothing are interposed between the hot particle source and the skin, and in cases where the hot particle is large in comparison to the range of beta particles. Once the protective clothing layer is thicker than the maximum range of the beta particles, skin dose is due solely to gamma radiation. Charged particle equilibrium is not established at shallow depths. The degree of electronic equilibrium establishment must be assessed for shallow doses to prevent the over-assessment of skin dose because conventional fluence-to-dose conversion factors are not applicable. To assess the effect of electronic equilibrium, selected thicknesses of tissue equivalent material were interposed between radiochromic dye film and a 60 Co hot particle source and dose was measured as a function of depth. These measured values were then compared to models which are used to calculate charged particle equilibrium. The Miller-Reece model was found to agree closely with the experimental data while the Lantz-Lambert model overestimated dose at shallow depths

  11. Comparisons between a new point kernel-based scheme and the infinite plane source assumption method for radiation calculation of deposited airborne radionuclides from nuclear power plants.

    Science.gov (United States)

    Zhang, Xiaole; Efthimiou, George; Wang, Yan; Huang, Meng

    2018-04-01

    Radiation from the deposited radionuclides is indispensable information for environmental impact assessment of nuclear power plants and emergency management during nuclear accidents. Ground shine estimation is related to multiple physical processes, including atmospheric dispersion, deposition, soil and air radiation shielding. It still remains unclear that whether the normally adopted "infinite plane" source assumption for the ground shine calculation is accurate enough, especially for the area with highly heterogeneous deposition distribution near the release point. In this study, a new ground shine calculation scheme, which accounts for both the spatial deposition distribution and the properties of air and soil layers, is developed based on point kernel method. Two sets of "detector-centered" grids are proposed and optimized for both the deposition and radiation calculations to better simulate the results measured by the detectors, which will be beneficial for the applications such as source term estimation. The evaluation against the available data of Monte Carlo methods in the literature indicates that the errors of the new scheme are within 5% for the key radionuclides in nuclear accidents. The comparisons between the new scheme and "infinite plane" assumption indicate that the assumption is tenable (relative errors within 20%) for the area located 1 km away from the release source. Within 1 km range, the assumption mainly causes errors for wet deposition and the errors are independent of rain intensities. The results suggest that the new scheme should be adopted if the detectors are within 1 km from the source under the stable atmosphere (classes E and F), or the detectors are within 500 m under slightly unstable (class C) or neutral (class D) atmosphere. Otherwise, the infinite plane assumption is reasonable since the relative errors induced by this assumption are within 20%. The results here are only based on theoretical investigations. They should

  12. Advection-diffusion model for the simulation of air pollution distribution from a point source emission

    Science.gov (United States)

    Ulfah, S.; Awalludin, S. A.; Wahidin

    2018-01-01

    Advection-diffusion model is one of the mathematical models, which can be used to understand the distribution of air pollutant in the atmosphere. It uses the 2D advection-diffusion model with time-dependent to simulate air pollution distribution in order to find out whether the pollutants are more concentrated at ground level or near the source of emission under particular atmospheric conditions such as stable, unstable, and neutral conditions. Wind profile, eddy diffusivity, and temperature are considered in the model as parameters. The model is solved by using explicit finite difference method, which is then visualized by a computer program developed using Lazarus programming software. The results show that the atmospheric conditions alone influencing the level of concentration of pollutants is not conclusive as the parameters in the model have their own effect on each atmospheric condition.

  13. Historic Sites and National Register of Historic Places - BRIDGES_HISTORIC_IDNR_IN: Historic Bridge Locations in Indiana (Indiana Department of Natural Resources, Division of Historic Preservation and Archaeology, 1:5,000, Point Shapefile)

    Data.gov (United States)

    NSGIC State | GIS Inventory — IDNR documentation states - “This dataset contains point locations of historic bridges in Indiana. It includes buildings, districts, sites, structures and objects...

  14. NOAA Point Shapefile - ROV transects - Locations of underwater photos and/or video collected in the US Caribbean - south of Vieques and in and around the Grand Reserve northeast of Puerto Rico (2013)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This point shapefile denotes the location of underwater photos and/or video that were collected by NOAA scientists using a Spectrum Phantom S2 ROV (remotely operated...

  15. Vibration of a Cylindrical Tunnel under a Centric Point-Source Explosion

    Directory of Open Access Journals (Sweden)

    Yuetang Zhao

    2017-01-01

    Full Text Available Underground tunnels are vulnerable to terrorists’ bombing attacks, which calls for studies on tunnel’s response to internal explosive loading. In this paper, the dynamic response of a cylindrical tunnel to an ideal centric point explosion was treated as an axisymmetric 2-dimensional problem, in which the tunnel was modeled with a continuous anisotropic shell, while the ground medium’s effect was accounted for with linear elastic Winkler springs and the explosive loading described by a temporal and spatial function. The governing equation of the motion is a fourth-order partial differential equation, for which a numerical method combining finite difference with the implicit Newmark-β method was adopted. This method avoided complicated integral transform and numerical inverse transformation, thus allowing efficient parameter study. The maximum radial displacement was found on the cricle of the center of explosive, where hoop stress is the maximum principal stress. The anisotropy showed little influence on maximum hoop stress. Within the range of ground medium’s modulus, minor influence on maximum hoop stress was incurred. This research may be helpful to hazard assessment and protective design for some critical subway tunnels.

  16. DEEP GALEX UV SURVEY OF THE KEPLER FIELD. I. POINT SOURCE CATALOG

    International Nuclear Information System (INIS)

    Olmedo, Manuel; Chávez, Miguel; Bertone, Emanuele; Lloyd, James; Mamajek, Eric E.; Martin, D. Christopher; Neill, James D.

    2015-01-01

    We report observations of a deep near-ultraviolet (NUV) survey of the Kepler field made in 2012 with the Galaxy Evolution Explorer (GALEX) Complete All-Sky UV Survey Extension (CAUSE). The GALEX-CAUSE Kepler survey (GCK) covers 104 square degrees of the Kepler field and reaches a limiting magnitude of NUV ≃ 22.6 at 3σ. Analysis of the GCK survey has yielded a catalog of 669,928 NUV sources, of which 475,164 are cross-matched with stars in the Kepler Input Catalog. Approximately 327 of 451 confirmed exoplanet host stars and 2614 of 4696 candidate exoplanet host stars identified by Kepler have NUV photometry in the GCK survey. The GCK catalog should enable the identification and characterization of UV-excess stars in the Kepler field (young solar-type and low-mass stars, chromospherically active binaries, white dwarfs, horizontal branch stars, etc.), and elucidation of various astrophysics problems related to the stars and planetary systems in the Kepler field

  17. Mitigation of non-point source of fluoride on groundwater by dug well recharge

    Science.gov (United States)

    Ganesan, G.; Lakshmanan, E.

    2017-12-01

    Groundwater used for drinking purpose is affected in many regions due to the presence of excess fluoride. The excess intake of fluoride through drinking water causes fluorosis to human in many states of India, including Tamil Nadu. The present study was carried out with the objective of assessing hydrogeochemistry of groundwater and the feasibility of dug well recharge to reduce the fluoride concentration in Vaniyar river basin, Tamil Nadu, India. The major source for fluoride in groundwater of this area is the epidote hornblende gneissic and charnockite which are the major rocks occurring in this region. As a pilot study a cost effective induced recharge structure was constructed at Papichettipatty village in the study region. The study shows that the groundwater level around the recharge site raised up to 2 m from 14.5 m (bgl) and fluoride concentration has decreased from 3.8 mg/l to 0.9 mg/l due to dilution. The advantage of this induced recharge structure is of its low cost, the ease of implementation, improved groundwater recharge and dilution of fluoride in groundwater. An area of about 1.5 km2 has benefited due to this dug well recharge system.

  18. Identifying non-point sources of endocrine active compounds and their biological impacts in freshwater lakes

    Science.gov (United States)

    Baker, Beth H.; Martinovic-Weigelt, Dalma; Ferrey, Mark L.; Barber, Larry B.; Writer, Jeffrey H.; Rosenberry, Donald O.; Kiesling, Richard L.; Lundy, James R.; Schoenfuss, Heiko L.

    2014-01-01

    Contaminants of emerging concern, particularly endocrine active compounds (EACs), have been identified as a threat to aquatic wildlife. However, little is known about the impact of EACs on lakes through groundwater from onsite wastewater treatment systems (OWTS). This study aims to identify specific contributions of OWTS to Sullivan Lake, Minnesota, USA. Lake hydrology, water chemistry, caged bluegill sunfish (Lepomis macrochirus), and larval fathead minnow (Pimephales promelas) exposures were used to assess whether EACs entered the lake through OWTS inflow and the resultant biological impact on fish. Study areas included two OWTS-influenced near-shore sites with native bluegill spawning habitats and two in-lake control sites without nearby EAC sources. Caged bluegill sunfish were analyzed for plasma vitellogenin concentrations, organosomatic indices, and histological pathologies. Surface and porewater was collected from each site and analyzed for EACs. Porewater was also collected for laboratory exposure of larval fathead minnow, before analysis of predator escape performance and gene expression profiles. Chemical analysis showed EACs present at low concentrations at each study site, whereas discrete variations were reported between sites and between summer and fall samplings. Body condition index and liver vacuolization of sunfish were found to differ among study sites as did gene expression in exposed larval fathead minnows. Interestingly, biological exposure data and water chemistry did not match. Therefore, although results highlight the potential impacts of seepage from OWTS, further investigation of mixture effects and life history factor as well as chemical fate is warranted.

  19. Event-based motion correction for PET transmission measurements with a rotating point source

    International Nuclear Information System (INIS)

    Zhou, Victor W; Kyme, Andre Z; Meikle, Steven R; Fulton, Roger

    2011-01-01

    Accurate attenuation correction is important for quantitative positron emission tomography (PET) studies. When performing transmission measurements using an external rotating radioactive source, object motion during the transmission scan can distort the attenuation correction factors computed as the ratio of the blank to transmission counts, and cause errors and artefacts in reconstructed PET images. In this paper we report a compensation method for rigid body motion during PET transmission measurements, in which list mode transmission data are motion corrected event-by-event, based on known motion, to ensure that all events which traverse the same path through the object are recorded on a common line of response (LOR). As a result, the motion-corrected transmission LOR may record a combination of events originally detected on different LORs. To ensure that the corresponding blank LOR records events from the same combination of contributing LORs, the list mode blank data are spatially transformed event-by-event based on the same motion information. The number of counts recorded on the resulting blank LOR is then equivalent to the number of counts that would have been recorded on the corresponding motion-corrected transmission LOR in the absence of any attenuating object. The proposed method has been verified in phantom studies with both stepwise movements and continuous motion. We found that attenuation maps derived from motion-corrected transmission and blank data agree well with those of the stationary phantom and are significantly better than uncorrected attenuation data.

  20. Entropy-Weighted Instance Matching Between Different Sourcing Points of Interest

    Directory of Open Access Journals (Sweden)

    Lin Li

    2016-01-01

    Full Text Available The crucial problem for integrating geospatial data is finding the corresponding objects (the counterpart from different sources. Most current studies focus on object matching with individual attributes such as spatial, name, or other attributes, which avoids the difficulty of integrating those attributes, but at the cost of an ineffective matching. In this study, we propose an approach for matching instances by integrating heterogeneous attributes with the allocation of suitable attribute weights via information entropy. First, a normalized similarity formula is developed, which can simplify the calculation of spatial attribute similarity. Second, sound-based and word segmentation-based methods are adopted to eliminate the semantic ambiguity when there is a lack of a normative coding standard in geospatial data to express the name attribute. Third, category mapping is established to address the heterogeneity among different classifications. Finally, to address the non-linear characteristic of attribute similarity, the weights of the attributes are calculated by the entropy of the attributes. Experiments demonstrate that the Entropy-Weighted Approach (EWA has good performance both in terms of precision and recall for instance matching from different data sets.

  1. [Estimation of urban non-point source pollution loading and its factor analysis in the Pearl River Delta].

    Science.gov (United States)

    Liao, Yi-Shan; Zhuo, Mu-Ning; Li, Ding-Qiang; Guo, Tai-Long

    2013-08-01

    In the Pearl Delta region, urban rivers have been seriously polluted, and the input of non-point source pollution materials, such as chemical oxygen demand (COD), into rivers cannot be neglected. During 2009-2010, the water qualities at eight different catchments in the Fenjiang River of Foshan city were monitored, and the COD loads for eight rivulet sewages were calculated in respect of different rainfall conditions. Interesting results were concluded in our paper. The rainfall and landuse type played important roles in the COD loading, with greater influence of rainfall than landuse type. Consequently, a COD loading formula was constructed that was defined as a function of runoff and landuse type that were derived SCS model and land use map. Loading of COD could be evaluated and predicted with the constructed formula. The mean simulation accuracy for single rainfall event was 75.51%. Long-term simulation accuracy was better than that of single rainfall. In 2009, the estimated COD loading and its loading intensity were 8 053 t and 339 kg x (hm2 x a)(-1), and the industrial land was regarded as the main source of COD pollution area. The severe non-point source pollution such as COD in Fenjiang River must be paid more attention in the future.

  2. A Single Phase Doubly Grounded Semi-Z-Source Inverter for Photovoltaic (PV Systems with Maximum Power Point Tracking (MPPT

    Directory of Open Access Journals (Sweden)

    Tofael Ahmed

    2014-06-01

    Full Text Available In this paper, a single phase doubly grounded semi-Z-source inverter with maximum power point tracking (MPPT is proposed for photovoltaic (PV systems. This proposed system utilizes a single-ended primary inductor (SEPIC converter as DC-DC converter to implement the MPPT algorithm for tracking the maximum power from a PV array and a single phase semi-Z-source inverter for integrating the PV with AC power utilities. The MPPT controller utilizes a fast-converging algorithm to track the maximum power point (MPP and the semi-Z-source inverter utilizes a nonlinear SPWM to produce sinusoidal voltage at the output. The proposed system is able to track the MPP of PV arrays and produce an AC voltage at its output by utilizing only three switches. Experimental results show that the fast-converging MPPT algorithm has fast tracking response with appreciable MPP efficiency. In addition, the inverter shows the minimization of common mode leakage current with its ground sharing feature and reduction of the THD as well as DC current components at the output during DC-AC conversion.

  3. Loop Heat Pipe Transient Behavior Using Heat Source Temperature for Set Point Control with Thermoelectric Converter on Reservoir

    Science.gov (United States)

    Ku, Jentung; Paiva, Kleber; Mantelli, Marcia

    2011-01-01

    The LHP operating temperature is governed by the saturation temperature of its reservoir. Controlling the reservoir saturation temperature is commonly done by cold biasing the reservoir and using electrical heaters to provide the required control power. With this method, the loop operating temperature can be controlled within 0.5K or better. However, because the thermal resistance that exists between the heat source and the LHP evaporator, the heat source temperature will vary with its heat output even if the LHP operating temperature is kept constant. Since maintaining a constant heat source temperature is of most interest, a question often raised is whether the heat source temperature can be used for LHP set point temperature control. A test program with a miniature LHP was carried out to investigate the effects on the LHP operation when the control temperature sensor was placed on the heat source instead of the reservoir. In these tests, the LHP reservoir was cold-biased and was heated by a control heater. Test results show that it was feasible to use the heat source temperature for feedback control of the LHP operation. In particular, when a thermoelectric converter was used as the reservoir control heater, the heat source temperature could be maintained within a tight range using a proportional-integral-derivative or on/off control algorithm. Moreover, because the TEC could provide both heating and cooling to the reservoir, temperature oscillations during fast transients such as loop startup could be eliminated or substantially reduced when compared to using an electrical heater as the control heater.

  4. Late Neogene Volcanic Stratigraphy in the Southern Puertecitos Volcanic Province of Baja California: Time Constraints and Vent Source Location

    Science.gov (United States)

    Garcia-Carrillo, P.; Martin, A.; Lopez-Martinez, M.; Cañon, E.

    2007-05-01

    during the opening of the Lower Delfin basin has been accommodated to the east. Our data support multiple source vents located offshore the central Puertecitos Volcanic Province. These pyroclastic flows may constitute useful marker horizons in marine seismic lines for reconstructing the timing and amount of extension across conjugate margins in the Lower Delfin basin.

  5. Helicobacter pylori infection in pregnant women in four districts of Uganda: role of geographic location, education and water sources.

    Science.gov (United States)

    Baingana, Rhona Kezabu; Kiboko Enyaru, John; Davidsson, Lena

    2014-09-04

    The prevalence of Helicobacter pylori infection varies in relation to geography, ethnicity and socioeconomic factors. Available data on the prevalence of Helicobacter pylori infection in Uganda are not representative of the general population. We sought to describe the epidemiology of this infection in pregnant women in Uganda to provide background data for a study into the effect of H. pylori infection during pregnancy on the hematological response to iron supplementation. Using a cross-sectional design, H. pylori infection was assessed by the stool antigen test among 447 pregnant women attending antenatal care clinics in Apac, Mbale, Mbarara and Rakai Districts which are in different geographical regions in Uganda, and at Kawempe Health Center which serves a low-income densely populated area in Kampala City. Socio-demographic and household data were collected by face-to-face interviews using a questionnaire. Associations between H. pylori infection and socio-demographic and household characteristics were analyzed using logistic regression. The overall prevalence of H. pylori infection was 45.2% but varied by geographical location from 18.2% in Apac District to 60.5% at Kawempe Health Centre. At 18.4%, the Langi ethnic group, who were enrolled exclusively in Apac District, had the lowest prevalence of H. pylori infection while the Gisu had the highest prevalence (58.4%). H. pylori was independently associated with enrollment at clinics not in Apac (adjusted OR = 5.68; 95% CI: 3.02-10.7) and with using water from public wells, boreholes or springs (AOR = 3.20; 95% CI: 1.19-8.61) and from rivers, lakes or streams (AOR = 5.20; 95% CI: 1.58-17.05). Urban residence (AOR = 1.71; 95% CI: 1.13-2.60) and no formal education (AOR = 1.95; 95% CI: 1.03-3.67) were also independently associated with H. pylori infection. The unexpected variation in the prevalence of H. pylori infection in Uganda calls for population-based studies in the region and offers an opportunity to study

  6. Inverse identification of unknown finite-duration air pollutant release from a point source in urban environment

    Science.gov (United States)

    Kovalets, Ivan V.; Efthimiou, George C.; Andronopoulos, Spyros; Venetsanos, Alexander G.; Argyropoulos, Christos D.; Kakosimos, Konstantinos E.

    2018-05-01

    In this work, we present an inverse computational method for the identification of the location, start time, duration and quantity of emitted substance of an unknown air pollution source of finite time duration in an urban environment. We considered a problem of transient pollutant dispersion under stationary meteorological fields, which is a reasonable assumption for the assimilation of available concentration measurements within 1 h from the start of an incident. We optimized the calculation of the source-receptor function by developing a method which requires integrating as many backward adjoint equations as the available measurement stations. This resulted in high numerical efficiency of the method. The source parameters are computed by maximizing the correlation function of the simulated and observed concentrations. The method has been integrated into the CFD code ADREA-HF and it has been tested successfully by performing a series of source inversion runs using the data of 200 individual realizations of puff releases, previously generated in a wind tunnel experiment.

  7. An open, interoperable, transdisciplinary approach to a point cloud data service using OGC standards and open source software.

    Science.gov (United States)

    Steer, Adam; Trenham, Claire; Druken, Kelsey; Evans, Benjamin; Wyborn, Lesley

    2017-04-01

    High resolution point clouds and other topology-free point data sources are widely utilised for research, management and planning activities. A key goal for research and management users is making these data and common derivatives available in a way which is seamlessly interoperable with other observed and modelled data. The Australian National Computational Infrastructure (NCI) stores point data from a range of disciplines, including terrestrial and airborne LiDAR surveys, 3D photogrammetry, airborne and ground-based geophysical observations, bathymetric observations and 4D marine tracers. These data are stored alongside a significant store of Earth systems data including climate and weather, ecology, hydrology, geoscience and satellite observations, and available from NCI's National Environmental Research Data Interoperability Platform (NERDIP) [1]. Because of the NERDIP requirement for interoperability with gridded datasets, the data models required to store these data may not conform to the LAS/LAZ format - the widely accepted community standard for point data storage and transfer. The goal for NCI is making point data discoverable, accessible and useable in ways which allow seamless integration with earth observation datasets and model outputs - in turn assisting researchers and decision-makers in the often-convoluted process of handling and analyzing massive point datasets. With a use-case of providing a web data service and supporting a derived product workflow, NCI has implemented and tested a web-based point cloud service using the Open Geospatial Consortium (OGC) Web Processing Service [2] as a transaction handler between a web-based client and server-side computing tools based on a native Linux operating system. Using this model, the underlying toolset for driving a data service is flexible and can take advantage of NCI's highly scalable research cloud. Present work focusses on the Point Data Abstraction Library (PDAL) [3] as a logical choice for

  8. Broadband integrated mid infrared light sources as enabling technology for point of care mid-infrared spectroscopy

    Science.gov (United States)

    2017-08-20

    DD-MM-YYYY)      06-09-2017 2. REPORT TYPE Final 3. DATES COVERED (From - To) 01 Aug 2016 to 31 Jul 2017 4. TITLE AND SUBTITLE Broadband integrated ...AFRL-AFOSR-JP-TR-2017-0061 Broadband integrated mid-infrared light sources as enabling technology for point-of-care mid- infrared spectroscopy Alex...Fuerbach MACQUARIE UNIVERSITY Final Report 08/20/2017 DISTRIBUTION A: Distribution approved for public release. AF Office Of Scientific Research (AFOSR

  9. New approach to the decision of Wilier - de Witt equation in the application to the point sources

    International Nuclear Information System (INIS)

    Fil'chenkov, M.L.

    2000-01-01

    A new approach to solution of the Wilier-de Witt equation based on quantization by free parameters of metrics satisfying the Einstein equations is suggested. The approach is applied to two point sources described by the Tangherlini metrics (in n-dimensional space) and the Reissner-Nordstrom metrics (in the presence of a charge). The results obtained clarify the essence of the Wilier hypothesis on high statistical weights of small dimensions and provide a new approach to the problem of fundamental constants variation [ru

  10. Generalised Predictive Control of a 12-bus Network Using Neutral-Point Clamped Voltage Source Converter UPFC

    OpenAIRE

    Zhang, L; Kokkinakis, M; Chong, BVP

    2014-01-01

    The paper presents the application of a UPFC to a case study of a 12-bus high power network. The UPFC shunt converter employs 8 3-level Neutral Point Clamped (NPC) voltage source converters (VSC) and 12 single-phase three-winding phase shifting transformers (PST), generating a 48-pulse output voltage. The 3-phase H-bridge series converter shares the same dc-link with the shunt one. The novel feature of this work lies in the use of a model-based generalised predictive current control law to th...

  11. DISCRIMINATION OF NATURAL AND NON-POINT SOURCE EFFECTS FROM ANTHROGENIC EFFECTS AS REFLECTED IN BENTHIC STATE IN THREE ESTUARIES IN NEW ENGLAND

    Science.gov (United States)

    In order to protect estuarine resources, managers must be able to discern the effects of natural conditions and non-point source effects, and separate them from multiple anthropogenic point source effects. Our approach was to evaluate benthic community assemblages, riverine nitro...

  12. Field methods for determining point source pollution impacts in rivers: A case study of the Grindsted stream

    DEFF Research Database (Denmark)

    McKnight, Ursula S.; Sonne, Anne Thobo; Fjordbøge, Annika Sidelmann

    2013-01-01

    Well-known organic contaminants such as chlorinated solvents, as well as new classes of compounds or emerging micropollutants (e.g. pharmaceuticals) are extensively produced, utilized and then discarded in society and subsequently released to streams from multiple sources. To address this, the EU......, and (ii) perform a risk assessment of the stream’s chemical status, including documentation of emerging contaminants. A secondary aim was to identify and ideally separate the entry point for the two plumes to Grindsted stream. We successfully detected six significant local-scale GSI “contact” zones along...... Water Framework Directive requires member states to evaluate all types of contamination sources within a watershed in order to assess their direct impact on water quality. Understanding and accurately characterizing groundwater-surface water interactions (GSI) and groundwater discharge is thus becoming...

  13. Considering a point-source in a regional air pollution model; Prise en compte d`une source ponctuelle dans un modele regional de pollution atmospherique

    Energy Technology Data Exchange (ETDEWEB)

    Lipphardt, M.

    1997-06-19

    This thesis deals with the development and validation of a point-source plume model, with the aim to refine the representation of intensive point-source emissions in regional-scale air quality models. The plume is modelled at four levels of increasing complexity, from a modified Gaussian plume model to the Freiberg and Lusis ring model. Plume elevation is determined by Netterville`s plume rise model, using turbulence and atmospheric stability parameters. A model for the effect of a fine-scale turbulence on the mean concentrations in the plume is developed and integrated in the ring model. A comparison between results with and without considering micro-mixing shows the importance of this effect in a chemically reactive plume. The plume model is integrated into the Eulerian transport/chemistry model AIRQUAL, using an interface between Airqual and the sub-model, and interactions between the two scales are described. A simulation of an air pollution episode over Paris is carried out, showing that the utilization of such a sub-scale model improves the accuracy of the air quality model

  14. Atmospheric observations for quantifying emissions of point-source synthetic greenhouse gases (CF4, NF3 and HFC-23)

    Science.gov (United States)

    Arnold, Tim; Manning, Alistair J.; Li, Shanlan; Kim, Jooil; Park, Sunyoung; Fraser, Paul J.; Mitrevski, Blagoj; Steele, L. Paul; Krummel, Paul B.; Mühle, Jens; Weiss, Ray F.

    2016-04-01

    The fluorinated species carbon tetrafluoride (CF4; PFC-14), nitrogen trifluoride (NF3) and trifluoromethane (CHF3; HFC-23) are potent greenhouse gases with 100-year global warming potentials of 6,630, 16,100 and 12,400, respectively. Unlike the majority of CFC-replacement compounds that are emitted from fugitive and mobile emission sources, these gases are largely emitted from large single point sources - semiconductor manufacturing facilities (all three), aluminium smelting plants (CF4) and chlorodifluoromethane factories (HFC-23). In this work we show the potential for atmospheric measurements to understand regional sources of these gases and to highlight emission 'hotspots'. We target our analysis on measurements from two Advanced Global Atmospheric Gases Experiment (AGAGE) long term monitoring sites that are particularly sensitive to regional emissions of these gases: Gosan on Jeju Island in the Republic of Korea and Cape Grim on Tasmania in Australia. These sites measure CF4, NF3 and HFC-23 alongside a suite of greenhouse and stratospheric ozone depleting gases every two hours using automated in situ gas-chromatography mass-spectrometry instrumentation. We couple each measurement to an analysis of air history using the regional atmospheric transport model NAME (Numerical Atmospheric dispersion Modelling Environment) driven by 3D meteorology from the Met Office's Unified Model, and use a Bayesian inverse method (InTEM - Inversion Technique for Emission Modelling) to calculate yearly emission changes over a decade (2005-2015) at high spatial resolution. At present these gases make a small contribution to global radiative forcing, however, given that their impact could rise significantly and that point sources of such gases can be mitigated, atmospheric monitoring could be an important tool for aiding emissions reduction policy.

  15. Analysis of point source pollution and water environmental quality variation trends in the Nansi Lake basin from 2002 to 2012.

    Science.gov (United States)

    Wang, Weiliang; Liu, Xiaohui; Wang, Yufan; Guo, Xiaochun; Lu, Shaoyong

    2016-03-01

    Based on the data analysis of the water environmental quality and economic development from 2002 to 2012 in the Nansi Lake basin, the correlation and change between the water environmental quality and economic development were studied. Results showed that the GDP and wastewater emissions of point source in the Nansi Lake basin had an average annual growth of 7.30 and 7.68 %, respectively, from 2002 to 2012. The emissions of chemical oxygen demand (COD) and ammonia nitrogen (NH3-N) had the average annual decrease of 7.69 and 6.79 % in 2012, respectively, compared to 2002. Basin water quality overall improved, reaching the Class III of the "Environmental quality standards for surface water (GB3838-2002)," in which the main reason was that sewage treatment rate increased gradually and was above 90 % in 2012 (an increase of 10 % compared to 2002) with the progress of pollution abatement technology and the implementation of relevant policies and regulations. The contribution of water environmental pollution was analyzed from related cities (Ji'ning, Zaozhuang, Heze). Results indicated that Ji'ning had the largest contribution to water pollution of the Nansi Lake basin, and the pollutant from domestic sources accounted for a higher percentage compared to industrial sources. The wastewater, COD, and NH3-N mainly came from mining and washing of coal, manufacture of raw chemical materials and chemical products, papermaking industry, and food processing industry. According to the water pollution characteristics of the Nansi Lake basin, the basin pollution treatment strategy and prevention and treatment system were dissected to provide a scientific basis for prevention and control of lakeside point source pollution along the Nansi Lake.

  16. Searches for Extended and Point-like Neutrino Sources with Four Years of IceCube Data

    Science.gov (United States)

    Aartsen, M. G.; Ackermann, M.; Adams, J.; Aguilar, J. A.; Ahlers, M.; Ahrens, M.; Altmann, D.; Anderson, T.; Arguelles, C.; Arlen, T. C.; Auffenberg, J.; Bai, X.; Barwick, S. W.; Baum, V.; Beatty, J. J.; Becker Tjus, J.; Becker, K.-H.; BenZvi, S.; Berghaus, P.; Berley, D.; Bernardini, E.; Bernhard, A.; Besson, D. Z.; Binder, G.; Bindig, D.; Bissok, M.; Blaufuss, E.; Blumenthal, J.; Boersma, D. J.; Bohm, C.; Bos, F.; Bose, D.; Böser, S.; Botner, O.; Brayeur, L.; Bretz, H.-P.; Brown, A. M.; Casey, J.; Casier, M.; Cheung, E.; Chirkin, D.; Christov, A.; Christy, B.; Clark, K.; Classen, L.; Clevermann, F.; Coenders, S.; Cowen, D. F.; Cruz Silva, A. H.; Danninger, M.; Daughhetee, J.; Davis, J. C.; Day, M.; de André, J. P. A. M.; De Clercq, C.; De Ridder, S.; Desiati, P.; de Vries, K. D.; de With, M.; DeYoung, T.; Díaz-Vélez, J. C.; Dunkman, M.; Eagan, R.; Eberhardt, B.; Eichmann, B.; Eisch, J.; Euler, S.; Evenson, P. A.; Fadiran, O.; Fazely, A. R.; Fedynitch, A.; Feintzeig, J.; Felde, J.; Feusels, T.; Filimonov, K.; Finley, C.; Fischer-Wasels, T.; Flis, S.; Franckowiak, A.; Frantzen, K.; Fuchs, T.; Gaisser, T. K.; Gallagher, J.; Gerhardt, L.; Gier, D.; Gladstone, L.; Glüsenkamp, T.; Goldschmidt, A.; Golup, G.; Gonzalez, J. G.; Goodman, J. A.; Góra, D.; Grandmont, D. T.; Grant, D.; Gretskov, P.; Groh, J. C.; Groß, A.; Ha, C.; Haack, C.; Haj Ismail, A.; Hallen, P.; Hallgren, A.; Halzen, F.; Hanson, K.; Hebecker, D.; Heereman, D.; Heinen, D.; Helbing, K.; Hellauer, R.; Hellwig, D.; Hickford, S.; Hill, G. C.; Hoffman, K. D.; Hoffmann, R.; Homeier, A.; Hoshina, K.; Huang, F.; Huelsnitz, W.; Hulth, P. O.; Hultqvist, K.; Hussain, S.; Ishihara, A.; Jacobi, E.; Jacobsen, J.; Jagielski, K.; Japaridze, G. S.; Jero, K.; Jlelati, O.; Jurkovic, M.; Kaminsky, B.; Kappes, A.; Karg, T.; Karle, A.; Kauer, M.; Kelley, J. L.; Kheirandish, A.; Kiryluk, J.; Kläs, J.; Klein, S. R.; Köhne, J.-H.; Kohnen, G.; Kolanoski, H.; Koob, A.; Köpke, L.; Kopper, C.; Kopper, S.; Koskinen, D. J.; Kowalski, M.; Kriesten, A.; Krings, K.; Kroll, G.; Kroll, M.; Kunnen, J.; Kurahashi, N.; Kuwabara, T.; Labare, M.; Larsen, D. T.; Larson, M. J.; Lesiak-Bzdak, M.; Leuermann, M.; Leute, J.; Lünemann, J.; Macías, O.; Madsen, J.; Maggi, G.; Maruyama, R.; Mase, K.; Matis, H. S.; Maunu, R.; McNally, F.; Meagher, K.; Medici, M.; Meli, A.; Meures, T.; Miarecki, S.; Middell, E.; Middlemas, E.; Milke, N.; Miller, J.; Mohrmann, L.; Montaruli, T.; Morse, R.; Nahnhauer, R.; Naumann, U.; Niederhausen, H.; Nowicki, S. C.; Nygren, D. R.; Obertacke, A.; Odrowski, S.; Olivas, A.; Omairat, A.; O'Murchadha, A.; Palczewski, T.; Paul, L.; Penek, Ö.; Pepper, J. A.; Pérez de los Heros, C.; Pfendner, C.; Pieloth, D.; Pinat, E.; Posselt, J.; Price, P. B.; Przybylski, G. T.; Pütz, J.; Quinnan, M.; Rädel, L.; Rameez, M.; Rawlins, K.; Redl, P.; Rees, I.; Reimann, R.; Resconi, E.; Rhode, W.; Richman, M.; Riedel, B.; Robertson, S.; Rodrigues, J. P.; Rongen, M.; Rott, C.; Ruhe, T.; Ruzybayev, B.; Ryckbosch, D.; Saba, S. M.; Sander, H.-G.; Sandroos, J.; Santander, M.; Sarkar, S.; Schatto, K.; Scheriau, F.; Schmidt, T.; Schmitz, M.; Schoenen, S.; Schöneberg, S.; Schönwald, A.; Schukraft, A.; Schulte, L.; Schulz, O.; Seckel, D.; Sestayo, Y.; Seunarine, S.; Shanidze, R.; Sheremata, C.; Smith, M. W. E.; Soldin, D.; Spiczak, G. M.; Spiering, C.; Stamatikos, M.; Stanev, T.; Stanisha, N. A.; Stasik, A.; Stezelberger, T.; Stokstad, R. G.; Stößl, A.; Strahler, E. A.; Ström, R.; Strotjohann, N. L.; Sullivan, G. W.; Taavola, H.; Taboada, I.; Tamburro, A.; Tepe, A.; Ter-Antonyan, S.; Terliuk, A.; Tešić, G.; Tilav, S.; Toale, P. A.; Tobin, M. N.; Tosi, D.; Tselengidou, M.; Unger, E.; Usner, M.; Vallecorsa, S.; van Eijndhoven, N.; Vandenbroucke, J.; van Santen, J.; Vehring, M.; Voge, M.; Vraeghe, M.; Walck, C.; Wallraff, M.; Weaver, Ch.; Wellons, M.; Wendt, C.; Westerhoff, S.; Whelan, B. J.; Whitehorn, N.; Wichary, C.; Wiebe, K.; Wiebusch, C. H.; Williams, D. R.; Wissing, H.; Wolf, M.; Wood, T. R.; Woschnagg, K.; Xu, D. L.; Xu, X. W.; Yanez, J. P.; Yodh, G.; Yoshida, S.; Zarzhitsky, P.; Ziemann, J.; Zierke, S.; Zoll, M.; IceCube Collaboration

    2014-12-01

    We present results on searches for point-like sources of neutrinos using four years of IceCube data, including the first year of data from the completed 86 string detector. The total livetime of the combined data set is 1373 days. For an E -2 spectrum, the observed 90% C.L. flux upper limits are ~10-12 TeV-1 cm-2 s-1 for energies between 1 TeV and 1 PeV in the northern sky and ~10-11 TeV-1 cm-2 s-1 for energies between 100 TeV and 100 PeV in the southern sky. This represents a 40% improvement compared to previous publications, resulting from both the additional year of data and the introduction of improved reconstructions. In addition, we present the first results from an all-sky search for extended sources of neutrinos. We update the results of searches for neutrino emission from stacked catalogs of sources and test five new catalogs; two of Galactic supernova remnants and three of active galactic nuclei. In all cases, the data are compatible with the background-only hypothesis, and upper limits on the flux of muon neutrinos are reported for the sources considered.

  17. MAGNETIC FIELD STRUCTURE OF THE HH 1-2 REGION: NEAR-INFRARED POLARIMETRY OF POINT-LIKE SOURCES

    International Nuclear Information System (INIS)

    Kwon, Jungmi; Pak, Soojong; Choi, Minho; Kandori, Ryo; Tamura, Motohide; Nagata, Tetsuya; Sato, Shuji

    2010-01-01

    The HH 1-2 region in the L1641 molecular cloud was observed in the near-infrared (IR) J, H, and K s bands, and imaging polarimetry was performed. Seventy-six point-like sources were detected in all three bands. The near-IR polarizations of these sources seem to be caused mostly by the dichroic extinction. Using a color-color diagram, reddened sources with little IR excess were selected to trace the magnetic field structure of the molecular cloud. The mean polarization position angle of these sources is about 111 deg., which is interpreted as the projected direction of the magnetic field in the observed region of the cloud. The distribution of the polarization angle has a dispersion of about 11 deg., which is smaller than what was measured in previous studies. This small dispersion gives a rough estimate of the strength of the magnetic field to be about 130 μG and suggests that the global magnetic field in this region is quite regular and straight. In contrast, the outflows driven by young stellar objects in this region seem to have no preferred orientation. This discrepancy suggests that the magnetic field in the L1641 molecular cloud does not dictate the orientation of the protostars forming inside.

  18. Transformer-based asymmetrical embedded Z-source neutral point clamped inverters with continuous input current and enhanced voltage boost capability

    DEFF Research Database (Denmark)

    Mo, W.; Loh, Poh Chiang; Blaabjerg, Frede

    2013-01-01

    Z-source Neutral Point Clamped (NPC) inverters were introduced to integrate both the advantages of Z-source inverters and NPC inverters. However, traditional Z-source inverters suffer from high voltage stress and chopping input current. This paper proposes six types transformer-based impedance-so......-source NPC inverters which have enhanced voltage boost capability and continuous input current by utilizing of transformer and embedded dc source configuration. Experimental results are presented to verify the theory validation....

  19. Identification of a time-varying point source in a system of two coupled linear diffusion-advection- reaction equations: application to surface water pollution

    International Nuclear Information System (INIS)

    Hamdi, Adel

    2009-01-01

    This paper deals with the identification of a point source (localization of its position and recovering the history of its time-varying intensity function) that constitutes the right-hand side of the first equation in a system of two coupled 1D linear transport equations. Assuming that the source intensity function vanishes before reaching the final control time, we prove the identifiability of the sought point source from recording the state relative to the second coupled transport equation at two observation points framing the source region. Note that at least one of the two observation points should be strategic. We establish an identification method that uses these records to identify the source position as the root of a continuous and strictly monotonic function. Whereas the source intensity function is recovered using a recursive formula without any need of an iterative process. Some numerical experiments on a variant of the surface water pollution BOD–OD coupled model are presented

  20. A generalized discontinuous PWM based neutral point voltage balancing method for three-level NPC voltage source inverter with switching losses reduction

    DEFF Research Database (Denmark)

    Li, Kai; Wei, Min; Xie, Chuan

    2017-01-01

    In order to control the neutral point voltage of inverter with discontinuous PWM (DPWM), this paper proposed a generalized discontinuous PWM (GDPWM) based neutral point voltage balancing method for three level neutral point clamped (NPC) voltage source inverter (VSI). Firstly, a triangle carrier ...