Investigation into the dissolution and direct assay of high-fired plutonium dioxide

International Nuclear Information System (INIS)

Patterson, J.K.

1976-01-01

A fusion-melt and dissolution assay method has been developed and tested for the quantitative analysis of high-fired plutonium dioxide. The method employs fusion of the plutonium dioxide at temperatures greater than the melting point of an eutectic mixture of potassium pyrosulfate plus sodium peroxide. The resultant melt is then titrated directly by either controlled potential coulometry or a gravimetric titration, using standardized ceric sulfate as the titrant. It has been concluded from these investigations that by using the techniques described, high-fired plutonium dioxide (stochiometric) can be quantitatively dissolved and assayed to a degree heretofore beyond the state-of-the-art, while showing direct traceability to the Federal standards. After fusion, the dissolution and direct assay is applicable to existing routine analytical procedures. The method was designed so as to minimize physical handling, simplify the chemical operations, and maximize the personal safety of the analyst at an appreciable cost savings per analysis

Nondestructive assay instrument for measurement of plutonium in solutions

International Nuclear Information System (INIS)

Shirk, D.G.; Hsue, F.; Li, T.K.; Canada, T.R.

1979-01-01

A nondestructive assay (NDA) instrument that measures the 239 Pu content in solutions, using a passive gamma-ray spectroscopy technique, has been developed and installed in the LASL Plutonium Processing Facility. A detailed evaluation of this instrument has been performed. The results show that the instrument can routinely determine 239 Pu concentrations of 1 to 500 g/l with accuracies of 1 to 5% and assay times of 1 to 2 x 10 3 s

Preparation of high purity plutonium oxide for radiochemistry instrument calibration standards and working standards

International Nuclear Information System (INIS)

Wong, A.S.; Stalnaker, N.D.

1997-04-01

Due to the lack of suitable high level National Institute of Standards and Technology (NIST) traceable plutonium solution standards from the NIST or commercial vendors, the CST-8 Radiochemistry team at Los Alamos National Laboratory (LANL) has prepared instrument calibration standards and working standards from a well-characterized plutonium oxide. All the aliquoting steps were performed gravimetrically. When a 241 Am standardized solution obtained from a commercial vendor was compared to these calibration solutions, the results agreed to within 0.04% for the total alpha activity. The aliquots of the plutonium standard solutions and dilutions were sealed in glass ampules for long term storage

Assay of plutonium contaminated waste by gamma spectrometry

International Nuclear Information System (INIS)

Adsley, I.; Bull, R.; Davies, M.; Green, M.

2011-01-01

The extreme toxicity of plutonium necessitates the segregation of plutonium contaminated materials (PCM) with extremely small (sub-μg) levels of contamination. The driver to measure accurately these small quantities of plutonium within (relatively) large volumes of waste is (in part) financial. In particular the cost of disposal (per unit volume) rises steeply with increasing waste-category. Within the UK, there has been a historical reluctance to use low energy gamma radiation to sentence PCM because of the potential for self attenuation by dense materials. This is unfortunate because the low-energy gamma radiation from PCM offers the only practicable technique for segregating PCM within the various Low Level Waste (LLW) (>0.4Bq/g) and sub-LLW categories. Whilst passive neutron counting techniques have proved successful for assay of waste well into the Intermediate Level Waste (ILW) (>100Bq/g) category, a cursory study reveals that these techniques are barely capable of detecting mg quantities of plutonium -- let alone the sub-μg quantities present in LLW. This paper considers the use of two types of gamma detector for assay of PCM: the thin sodium iodide FIDLER (Field Instrument for the Detection of Low Energy Radiation) and the HPGe (High Purity Germanium) detector. Systems utilising these two types of detector can provide complementary information. FIDLER measurements are conducted by careful, local, systematic monitoring of surfaces. By contrast a HPGe detector can be used to monitor entire walls, or even rooms, in one measurement. Thus, a HPGe detector placed in the centre of room (from which any radioactive hot-spots have previously been removed) could be used to demonstrate that the average activity remaining close to the surface of the walls/floor/ceiling is below a given limit. The Monte Carlo Code MCNP 1 has been used to model both FIDLER probe and HPGe detector in the measurement geometries described above. The MCNP simulations have been validated

Further Evaluation of the Neutron Resonance Transmission Analysis (NRTA) Technique for Assaying Plutonium in Spent Fuel

Energy Technology Data Exchange (ETDEWEB)

J. W. Sterbentz; D. L. Chichester

2011-09-01

This is an end-of-year report (Fiscal Year (FY) 2011) for the second year of effort on a project funded by the National Nuclear Security Administration's Office of Nuclear Safeguards (NA-241). The goal of this project is to investigate the feasibility of using Neutron Resonance Transmission Analysis (NRTA) to assay plutonium in commercial light-water-reactor spent fuel. This project is part of a larger research effort within the Next-Generation Safeguards Initiative (NGSI) to evaluate methods for assaying plutonium in spent fuel, the Plutonium Assay Challenge. The second-year goals for this project included: (1) assessing the neutron source strength needed for the NRTA technique, (2) estimating count times, (3) assessing the effect of temperature on the transmitted signal, (4) estimating plutonium content in a spent fuel assembly, (5) providing a preliminary assessment of the neutron detectors, and (6) documenting this work in an end of the year report (this report). Research teams at Los Alamos National Laboratory (LANL), Lawrence Berkeley National Laboratory (LBNL), Pacific Northwest National Laboratory (PNNL), and at several universities are also working to investigate plutonium assay methods for spent-fuel safeguards. While the NRTA technique is well proven in the scientific literature for assaying individual spent fuel pins, it is a newcomer to the current NGSI efforts studying Pu assay method techniques having just started in March 2010; several analytical techniques have been under investigation within this program for two to three years or more. This report summarizes work performed over a nine month period from January-September 2011 and is to be considered a follow-on or add-on report to our previous published summary report from December 2010 (INL/EXT-10-20620).

Evaluation of the neutron self-interrogation approach for assay of plutonium in high materials

International Nuclear Information System (INIS)

Russo, P.A.; Menlove, H.O.; Fife, K.W.; West, M.H.

1987-01-01

The pyrochemical scrap recovery processes, designed to extract impurities from plutonium metal and compounds, generate a variety of plutonium-laden residues consisting of high (α,n) matrices of varying chemical composition, and often containing grams to tens of grams of americium. For such materials, multiplication corrections based on real neutron coincidence count rate, R, and total neutron count rate, T, measurements cannot be applied because of the large, unknown, and variable (α,n) component in the total neutron emission rate. A study of the prototype self-interrogation assay method is in progress at the Los Alamos plutonium facility. In the self-interrogation approach, the assay signature R(IF)/T is a function of effective fissile plutonium content, where R(IF) is the induced fission component of the measured reals rate, and T is the measured, (α,n)-dominated totals rate. The present study includes a calibration effort using standards consisting of mixtures of PuO 2 and PuF 4 in a salt-strip matrix. The neutron measurements of the standards and the process materials have been performed at the Los Alamos Plutonium Facility. The precision and accuracy of the self-interrogation method applied to pyrochemical residues is examined in this study

Developments in plutonium waste assay at AWE

International Nuclear Information System (INIS)

Miller, T J

2009-01-01

In 2002 a paper was presented at the 43rd Annual Meeting of the Institute of Nuclear Materials Management (INMM) on the assay of low level plutonium (Pu) in soft drummed waste (Miller 2002 INMM Ann. Meeting (Orlando, FL, 23-27 July 2002)). The technique described enabled the Atomic Weapons Establishment (AWE), at Aldermaston in the UK, to meet the stringent Low Level Waste Repository at Drigg (LLWRD) conditions for acceptance for the first time. However, it was initially applied to only low density waste streams because it relied on measuring the relatively low energy (60 keV) photon yield from Am-241 during growth. This paper reviews the results achieved when using the technique to assay over 10 000 waste packages and presents the case for extending the range of application to denser waste streams.

Evaluation of a gamma-spectroscopy gauge for uranium-plutonium assay

International Nuclear Information System (INIS)

Notea, A.; Segal, Y.

1976-01-01

A procedure is presented for the characterization of a gamma passive method for non-destructive analysis of nuclear fuel. The approachh provides an organized and systematic way for optimizing the assay system. The key function is the relative resolving power defined as the smallest relative change in the quantity of radionuclide measured that may be detected within a certain confidence level. This function is derived for nuclear fuel employing a model based on empirical parameters. The ability to detect changes in fuels of binary and trinary compositions with a 50-cm 3 Ge(Li) at a 1-min counting period is discussed. As an example to a binary composition, an enriched uranium fuel was considered. The 185-keV and 1001-keV gamma lines are used for the assay of 235 U and 238 U, respectively. As a trinary composition a plutonium-containing fuel was examined. The plutonium was identified by the 414-keV gamma line. The interference of the high-energy lines is carefully analysed, and numerical results are presented. For both cases the range of measurement under specific accuracy demands is determined. The approac described is suitable also for evaluation of other passive as well as active assay methods. (author)

Monitoring of plutonium contaminated solid waste streams. Chapter IV: Passive neutron assay

International Nuclear Information System (INIS)

Birkhoff, G.; Bondar, L.

1978-01-01

The fundamentals of the passive neutron technique for the non destructive assay of plutonium bearing materials are summarized. A reference monitor for the passive neutron assay of Pu contaminated solids is described in terms of instrumental design principles and performances. The theoretical model of this reference monitor with pertinent nuclear data and functions for the interpretation of experimental data is given

Plutonium isotopic measurements by gamma-ray spectroscopy

International Nuclear Information System (INIS)

Haas, F.X.; Lemming, J.F.

1976-01-01

A nondestructive technique is described for calculating plutonium-238, plutonium-240, plutonium-241 and americium-241 relative to plutonium-239 from measured peak areas in the high resolution gamma-ray spectra of solid plutonium samples. Gamma-ray attenuation effects were minimized by selecting sets of neighboring peaks in the spectrum whose components are due to the different isotopes. Since the detector efficiencies are approximately the same for adjacent peaks, the accuracy of the isotopic ratios is dependent on the half-lives, branching intensities, and measured peak areas. The data presented describe the results obtained by analyzing gamma-ray spectra in the energy region from 120 to 700 keV. Most of the data analyzed were obtained from plutonium material containing 6 percent plutonium-240. Sample weights varied from 0.25 g to approximately 1.2 kg. The methods were also applied to plutonium samples containing up to 23 percent plutonium-240 with weights of 0.25 to 200 g. Results obtained by gamma-ray spectroscopy are compared to chemical analyses of aliquots taken from the bulk samples

Further development of the ceric oxidation ferrous reduction dichromate titration method of plutonium determination

International Nuclear Information System (INIS)

Macdonald, A.; Savage, D.J.

1986-02-01

The chemical reactions involved in the amperometric titration method for plutonium have been further examined, to identify remaining potential sources of bias. As these effects were not expected to be more than 0.1% at the 30 mg plutonium level, a procedure for analysing small (3 mg) aliquots of plutonium has been developed, to help identify any marginal effects. At this reduced level both plutonium and 'blank' determinations indicated that reduction of potassium permanganate by oxalic acid is slower than previously suspected and that a variable small bias can result. Decreasing the concentration of the potassium permanganate eliminated the latter effect. A low bias, proportional to the amount of excess oxalic acid added, was observed. Experiments suggest the bias is due to the reaction of oxalate with an intermediary in the iron II/ dichromate titration. The effect can be adequately reduced by complexing oxalate with cerium III. The reduction of plutonium VI by iron II has been shown to be faster than previously assumed, permitting a decreased waiting time before titration. Minor changes to the original procedure are recommended for analysis of 3 mg aliquots of plutonium. (author)

Nuclear fuel technology - Determination of milligram amounts of plutonium in nitric acid solutions - Potentiometric titration with potassium dichromate after oxidation by Ce(IV) and reduction by Fe(II)

International Nuclear Information System (INIS)

2000-01-01

This International Standard describes a precise and accurate analytical method for determining 1 mg to 5 mg of plutonium per millilitre in nitric acid solutions. The method is very selective for plutonium. It is suitable for the direct determination of plutonium in materials ranging from pure product solutions, to solutions of mixed nuclear materials with a uranium/plutonium ratio up to 20:1. However, potential application to the assay of plutonium in solutions of irradiated nuclear fuels and solutions of mixed nuclear materials with uranium/plutonium ratios of 20:1 to 33:1 has not yet been documented. The method recommends that the aliquot be weighed and that the titration burettes be calibrated gravimetrically in order to obtain adequate precision and accuracy. This does not preclude using any alternative technique which can be shown to give an equivalent accuracy. As the reproducibility of the reaction conditions is important to maintain good performance, extensive automatization of the procedure is beneficial

Nondestructive assay system development for a plutonium scrap recovery facility

International Nuclear Information System (INIS)

Hsue, S.T.; Baker, M.P.

1984-01-01

A plutonium scrap recovery facility is being constructed at the Savannah River Plant (SRP). The safeguards groups of the Los Alamos National Laboratory have been working since the early design stage of the facility with SRP and other national laboratories to develop a state-of-the-art assay system for this new facility. Not only will the most current assay techniques be incorporated into the system, but also the various nondestructive assay (NDA) instruments are to be integrated with an Instrument Control Computer (ICC). This undertaking is both challenging and ambitious; an entire assay system of this type has never been done before in a working facility. This paper will describe, in particular, the effort of the Los Alamos Safeguards Assay Group in this endeavor. Our effort in this project can be roughly divided into three phases: NDA development, system integration, and integral testing. 6 references

Neutron Resonance Transmission Analysis (NRTA): Initial Studies of a Method for Assaying Plutonium in Spent Fuel

Energy Technology Data Exchange (ETDEWEB)

David L. Chichester; James W. Sterbentz

2011-05-01

Neutron Resonance Transmission Analysis (NRTA) is an analytical technique that uses neutrons to assay the isotopic content of bulk materials. The technique uses a pulsed accelerator to produce an intense, short pulse of neutrons in a time-of-flight configuration. These neutrons, traveling at different speeds according to their energy, can be used to interrogate a spent fuel (SF) assembly to determine its plutonium content. Neutron transmission through the assembly is monitored as a function of neutron energy (time after the pulse), similar to the way neutron cross-section data is often collected. The transmitted neutron intensity is recorded as a function of time, with faster (higher-energy) neutrons arriving first and slower (lower-energy) neutrons arriving later. The low-energy elastic scattering and absorption resonances of plutonium and other isotopes modulate the transmitted neutron spectrum. Plutonium content in SF can be determined by analyzing this attenuation. Work is currently underway at Idaho National Laboratory, as a part of United States Department of Energy's Next Generation Safeguards Initiative (NGSI), to investigate the NRTA technique and to assess its feasibility for quantifying the plutonium content in SF and for determining the diversion of SF pins from assemblies. Preliminary results indicate that NRTA has great potential for being able to assay intact SF assemblies. Operating in the 1-40 eV range, it can identify four plutonium isotopes (239, 240, 241, & 242Pu), three uranium isotopes (235, 236, & 238U), and six resonant fission products (99Tc, 103Rh, 131Xe, 133Cs, 145Nd, and 152Sm). It can determine the areal density or mass of these isotopes in single- or multiple-pin integral transmission scans. Further, multiple observables exist to allow the detection of material diversion (pin defects) including fast-neutron and x-ray radiography, gross-transmission neutron counting, plutonium resonance absorption analysis, and fission

Standard test method for plutonium assay by plutonium (III) diode array spectrophotometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 This test method describes the determination of total plutonium as plutonium(III) in nitrate and chloride solutions. The technique is applicable to solutions of plutonium dioxide powders and pellets (Test Methods C 697), nuclear grade mixed oxides (Test Methods C 698), plutonium metal (Test Methods C 758), and plutonium nitrate solutions (Test Methods C 759). Solid samples are dissolved using the appropriate dissolution techniques described in Practice C 1168. The use of this technique for other plutonium-bearing materials has been reported (1-5), but final determination of applicability must be made by the user. The applicable concentration range for plutonium sample solutions is 10–200 g Pu/L. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropria...

Some examples of the estimation of error for calorimetric assay of plutonium-bearing solids

International Nuclear Information System (INIS)

Rodenburg, W.W.

1977-04-01

This report provides numerical examples of error estimation and related measurement assurance programs for the calorimetric assay of plutonium. It is primarily intended for users who do not consider themselves experts in the field of calorimetry. These examples will provide practical and useful information in establishing a calorimetric assay capability which fulfills regulatory requirements. 10 tables, 5 figures

Total Measurement Uncertainty for the Plutonium Finishing Plant (PFP) Segmented Gamma Scan Assay System

CERN Document Server

Fazzari, D M

2001-01-01

This report presents the results of an evaluation of the Total Measurement Uncertainty (TMU) for the Canberra manufactured Segmented Gamma Scanner Assay System (SGSAS) as employed at the Hanford Plutonium Finishing Plant (PFP). In this document, TMU embodies the combined uncertainties due to all of the individual random and systematic sources of measurement uncertainty. It includes uncertainties arising from corrections and factors applied to the analysis of transuranic waste to compensate for inhomogeneities and interferences from the waste matrix and radioactive components. These include uncertainty components for any assumptions contained in the calibration of the system or computation of the data. Uncertainties are propagated at 1 sigma. The final total measurement uncertainty value is reported at the 95% confidence level. The SGSAS is a gamma assay system that is used to assay plutonium and uranium waste. The SGSAS system can be used in a stand-alone mode to perform the NDA characterization of a containe...

The spectrographic analysis of plutonium oxide or mixed plutonium oxide/uranium oxide fuel pellets by the dried residue technique

International Nuclear Information System (INIS)

Jarbo, G.J.; Faught, P.; Hildebrandt, B.

1980-05-01

An emission spectrographic method for the quantitative determination of metallic impurities in plutonium oxide and mixed plutonium oxide/uranium oxide is described. The fuel is dissolved in nitric acid and the plutonium and/or uranium extracted with tributyl phosphate. A small aliquot of the aqueous residue is dried on a 'mini' pyrolitic graphite plate and excited by high voltage AC spark in an oxygen atmosphere. Spectra are recorded in a region which has been specially selected to record simultaneously lines of boron and cadmium in the 2nd order and all the other elements of interest in the 1st order. Indium is used as an internal standard. The excitation of very small quantities of the uraniumm/plutonium free residue by high voltage spark, together with three separate levels of containment reduce the hazards to personnel and the environment to a minimum with limited effect on sensitivity and accuracy of the results. (auth)

Evaluation of gamma spectroscopy gauge for uranium-plutonium assay

International Nuclear Information System (INIS)

Notea, A.; Segal, Y.

1975-01-01

A procedure is presented for the characterization of a gamma passive method for nondestructive analysis of nuclear fuel. The approach provides an organized and systematic way for optimizing the assay system. The key function is the relative resolving power defined as the smallest relative change in the Quantity of radionuclide measured, that may be detected within a certain confidence level. This function is derived for nuclear fuel employing a model based on empirical parameters. The ability to detect changes in fuels of binary and trinary compositions with a 50 cc Ge(Li) at a 1 min counting period is discussed. As an example to a binary composition, an enriched uranium fuel was considered. The 185 keV and 1001 keV gamma lines are used for the assay of 235 U and 238 U respectively. As a trinary composition a plutonium-containing gamma line. The interference of the high energy lines is carefully analyzed, and numerical results are presented. For both cases the range of measurement under specific accuracy demands is determined. The approach described is suitable also for evaluation of other passive as well as active assay methods. (author)

The MacDonald and savage titrimetric procedure for plutonium scaled-down to the milligram level: Automated procedure for routine analysis of safeguards samples containing 2 to 5 mg plutonium

International Nuclear Information System (INIS)

Ronesch, K.; Jammet, G.; Berger, J.; Doubek, N.; Bagliano, G.; Deron, S.

1992-08-01

A selective titrimetric procedure directly applicable to both input and product solutions from fast reactor fuel reprocessing was set up by MacDonald and Savage and scaled down to 3 mg of plutonium in sample aliquots at the request of the Safeguards Analytical Laboratory (SAL) of the International Atomic Energy Agency (IAEA), which needed to replace its silver (II) oxide titration procedure by a more selective electrochemical method. Although the procedure is very selective the following species still interfere: Vanadates (almost quantitatively), Neptunium (one electron exchange per mole); Nitrites, Fluorosilicates and Iodates present in mg amount yield slight biases. This paper describes the fully automatized procedure presently applied in SAL for the routine determination of 2 to 5 mg plutonium dissolved in nitric acid solution. The method allows the unattended analysis of 20 aliquots within a five hour period. The equipment including the reagent distribution system, the sample changer and the control units are introduced and the principle design of the software is shortly described. Safety requirements have been addressed and are also reviewed in the report. Results obtained on standard reference materials, international intercomparison samples and actual safeguards samples routinely analyzed with the proposed procedure are presented and compared with results achieved with the semiautomatic mode to demonstrate the performance. International requirements to reduce the amount of radioactive materials in waste will certainly lead to a further reduction of the amount of plutonium in one aliquot. Some future perspective to titrate 1 mg samples are presented in the discussion. 12 refs, 10 figs, 8 tabs

Plutonium in a grassland ecosystem

International Nuclear Information System (INIS)

Little, C.A.

1976-08-01

A study was made of plutonium contamination of grassland at the Rocky Flats plant northwest of Denver, Colorado. Of interest were: the definition of major plutonium-containing ecosystem compartments; the relative amounts in those compartments; how those values related to studies done in other geographical areas; whether or not the predominant isotopes, 238 Pu and 239 Pu, behaved differently; and what mechanisms might have allowed for the observed patterns of contamination. Samples of soil, litter, vegetation, arthropods, and small mammals were collected for Pu analysis and mass determination from each of two macroplots. Small aliquots (5 g or less) were analyzed by a rapid liquid scintillation technique and by alpha spectrometry. Of the compartments sampled, greater than 99 percent of the total plutonium was contained in the soil and the concentrations were significantly inversely correlated with distance from the contamination source, depth of the sample, and particle size of the sieved soil samples. The soil data suggested that the distribution of contamination largely resulted from physical transport processes

Cost comparison of methods for preparation of neonatal red cell aliquots.

Science.gov (United States)

Lechuga, Diana; Thompson, Christina

2007-01-01

The purpose of this study was to compare the preparation costs of two common methods used for neonatal red blood cell transfusion aliquots. Three months of data from a Level 2 and Level 3 neonatal intensive care unit (NICU) were used to determine the comparative cost for red cell aliquot transfusions using an eight bag aliquot/transfer system or the syringe set system. Using leuko-poor red blood cell blood collected in Adsol and containing approximately 320 ml of red blood cells and supernatant solution, the average cost of neonatal transfusion aliquots was determined using the Charter Medical syringe set and the Charter Medical eight bag aliquot/transfer system. A total of 126 red blood cell transfusion aliquots were used over the three month period. The amount transfused with each aliquot ranged from 5.0 ml - 55.0 ml with an average of 24.0 ml per aliquot. The cost per aliquot using the eight aliquot/transfer set was calculated as $36.25 and the cost per aliquot using the syringe set cost was calculated as $30.71. Additional benefits observed with the syringe set included decreased blood waste. When comparing Charter Medical multiple aliquot bag sets and the Charter Medical syringe aliquot system to provide neonatal transfusions, the use of the syringe system decreased blood waste and proved more cost effective.

Design of an error-free nondestructive plutonium assay facility

International Nuclear Information System (INIS)

Moore, C.B.; Steward, W.E.

1987-01-01

An automated, at-line nondestructive assay (NDA) laboratory is installed in facilities recently constructed at the Savannah River Plant. The laboratory will enhance nuclear materials accounting in new plutonium scrap and waste recovery facilities. The advantages of at-line NDA operations will not be realized if results are clouded by errors in analytical procedures, sample identification, record keeping, or techniques for extracting samples from process streams. Minimization of such errors has been a primary design objective for the new facility. Concepts for achieving that objective include mechanizing the administrative tasks of scheduling activities in the laboratory, identifying samples, recording and storing assay data, and transmitting results information to process control and materials accounting functions. These concepts have been implemented in an analytical computer system that is programmed to avoid the obvious sources of error encountered in laboratory operations. The laboratory computer exchanges information with process control and materials accounting computers, transmitting results information and obtaining process data and accounting information as required to guide process operations and maintain current records of materials flow through the new facility

Real-Time, Fast Neutron Coincidence Assay of Plutonium With a 4-Channel Multiplexed Analyzer and Organic Scintillators

Science.gov (United States)

Joyce, Malcolm J.; Gamage, Kelum A. A.; Aspinall, M. D.; Cave, F. D.; Lavietes, A.

2014-06-01

The design, principle of operation and the results of measurements made with a four-channel organic scintillator system are described. The system comprises four detectors and a multiplexed analyzer for the real-time parallel processing of fast neutron events. The function of the real-time, digital multiple-channel pulse-shape discrimination analyzer is described together with the results of laboratory-based measurements with 252Cf, 241Am-Li and plutonium. The analyzer is based on a single-board solution with integrated high-voltage supplies and graphical user interface. It has been developed to meet the requirements of nuclear materials assay of relevance to safeguards and security. Data are presented for the real-time coincidence assay of plutonium in terms of doubles count rate versus mass. This includes an assessment of the limiting mass uncertainty for coincidence assay based on a 100 s measurement period and samples in the range 0-50 g. Measurements of count rate versus order of multiplicity for 252Cf and 241Am-Li and combinations of both are also presented.

Maintenance of storage properties of pediatric aliquots of apheresis platelets in fluoroethylene propylene containers.

Science.gov (United States)

Skripchenko, Andrey; Myrup, Andrew; Thompson-Montgomery, Dedeene; Awatefe, Helen; Wagner, Stephen J

2013-04-01

Platelet (PLT) aliquots for pediatric use have been shown to retain in vitro properties when stored in gas-impermeable syringes for up to 6 hours. As an alternative, PLT aliquots can be stored for longer periods in containers used for storage of whole blood-derived PLTs. These containers are not available separate from whole blood collection sets and PLT volumes less than 35 mL either have not been evaluated or may be unsuitable for PLT storage. Gas-permeable fluoroethylene propylene (FEP) containers have been used in the storage of cell therapy preparations and are available in multiple sizes as single containers but have not been evaluated for PLT storage. A single apheresis unit was divided on Day 3 into small aliquots with volume ranging from 20 to 60 mL, transferred using a sterile connection device, and stored for an additional 2 days either in CLX (control) or in FEP containers. PLT storage properties of PLTs stored in FEP containers were compared to those stored in CLX containers. Standard PLT in vitro assays were performed (n =6). PLT storage properties were either similar to those of CLX containers or differed by less than 20% excepting carbon dioxide levels, which varied less than 60%. Pediatric PLT aliquots of 20, 30, and 60mL transferred on Day 3 into FEP cell culture containers adequately maintain PLT properties for an additional 2days of storage. © 2012 American Association of Blood Banks.

Prototype fast neutron counter for the assay of impure plutonium

International Nuclear Information System (INIS)

Wachter, J.R.; Adams, E.L.; Ensslin, N.

1987-01-01

A fast coincident neutron counter using liquid scintillators and gamma-ray/neutron pulse-shape discrimination has been constructed for the analysis of plutonium samples with unknown self-multiplication and (α,n) production. The counter was used to measure plutonium-bearing materials that cover a range of masses and (α,n) reaction rates of importance to the safeguards community. Measured values of the 240 Pu effective mass differed, on average, from their declared values by 0.4% for plutonium oxides and by -2.2% for metal and MgO-loaded samples. Poorer results were obtained for materials with large (α,n) reaction rates and low self-multiplication such as plutonium ash and plutonium fluoride

Passive assay of plutonium metal plates using a fast-neutron multiplicity counter

Energy Technology Data Exchange (ETDEWEB)

Di Fulvio, A., E-mail: difulvio@umich.edu [Department of Nuclear Engineering & Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Shin, T.H.; Jordan, T.; Sosa, C.; Ruch, M.L.; Clarke, S.D. [Department of Nuclear Engineering & Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Chichester, D.L. [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Pozzi, S.A. [Department of Nuclear Engineering & Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States)

2017-05-21

We developed a fast-neutron multiplicity counter based on organic scintillators (EJ-309 liquid and stilbene). The system detects correlated photon and neutron multiplets emitted by fission reactions, within a gate time of tens of nanoseconds. The system was used at Idaho National Laboratory to assay a variety of plutonium metal plates. A coincidence counting strategy was used to quantify the {sup 240}Pu effective mass of the samples. Coincident neutrons, detected within a 40-ns coincidence window, show a monotonic trend, increasing with the {sup 240}Pu-effective mass (in this work, we tested the 0.005–0.5 kg range). After calibration, the system estimated the {sup 240}Pu effective mass of an unknown sample ({sup 240}Pu{sub eff} >50 g) with an uncertainty lower than 1% in a 4-min assay time.

Plutonium in a grassland ecosystem

International Nuclear Information System (INIS)

Little, C.A.

1976-01-01

This study was concerned with plutonium contamination of grassland at the U.S. Energy Research and Development Administration Rocky Flats plant northwest of Denver, Colorado. Of interest were: the definition of major plutonium-containing ecosystem compartments; the relative amounts in those compartments; how those values related to studies done in other geogrphical areas; whether or not the predominant isotopes, 238 Pu and 239 Pu, behaved differently; and what mechanisms might have allowed for the observed patterns of contamination. Samples of soil, litter, vegetation, arthropods, and small mammals were collected for plutonium analysis and mass determination from each of two macroplots. Small aliquots (5 g or less) were analyzed by a rapid liquid scintillation technique and by alpha spectrometry. Of the compartments sampled, greater than 99% of the total plutonium was contained in the soil. The concentrations of plutonium in soil were significantly inversely correlated with distance from the contamination source, depth of the sample, and particle size of the sieved soil samples. The soil data suggested that the distribution of contamination largely resulted from physical transport processes. A mechanism of agglomerated submicron plutonium oxide particles and larger (1-500 μm) host soil particles was proposed. Concentrations of Pu in litter and vegetation were inversely correlated to distance from the source and directly correlated to soil concentrations at the same location. Comparatively high concentration ratios of vegetation to soil suggested wind resuspension of contamination as an important transport mechanism. Arthropod and small mammal samples were highly skewed, kurtotic, and quite variable, having coefficients of variation (standard deviation/mean) as high as 600%. Bone Pu concentrations were lower than other tissues. Hide, GI, and lung were generally not higher in Pu than kidney, liver and muscle

Studies on removal of plutonium from oxalic acid containing hydrochloric acid solutions

Energy Technology Data Exchange (ETDEWEB)

Ghadse, D R; Noronha, D M; Joshi, A R [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Solution containing hydrochloric acid, oxalic acid and considerable quantities of plutonium may be generated while recycling of scrap produced during the metallic fuel fabrication. Plutonium from such waste is normally recovered by anion exchange method after the destruction of oxalic acid using suitable oxidising agent. Solvent extraction and ion exchange methods are being explored in this laboratory for recovery of Pu from oxalic acid containing HCl solutions without prior destruction of oxalic acid. This paper describes the results on the determination of distribution ratios for extraction of Pu(IV) from hydrochloric acid using Aliquot-336 or HDEHP under varying experimental conditions. (author). 5 refs., 5 tabs.

Calorimetric systems designed for in-field nondestructive assay of plutonium-bearing materials

International Nuclear Information System (INIS)

Roche, C.T.; Perry, R.B.; Lewis, R.N.; Jung, E.A.; Haumann, J.R.

1978-01-01

Conventional calorimetric design measures the temperature rise of a plutonium-containing sample chamber in contact with a large water-bath heat sink. This design lacks the mobility needed by inspection personnel. The Argonne National Laboratory air-chamber isothermal calorimeters are low-thermal capacitance devices which eliminate the need for large, constant-temperature heat sinks. A bulk calorimeter designed to measure sealed containers holding up to 3 kg Pu, and a small-sample calorimeter designed to measure mixed-oxide fuel pellets and powders are discussed. The operational characteristics of these instruments are described, and the results of sample assays are presented

A programme for Euratom safeguards inspectors, used in the assay of plutonium bearing materials by passive neutron interrogation

International Nuclear Information System (INIS)

Vocino, V.; Farese, N.; Maucq, T.; Nebuloni, M.

1991-01-01

The programme PECC (Passive Euratom Coincidence Counters) has been developed at the Joint Research Center, Ispra by the Euratom Safeguards Directorate, Luxembourg and the Safety Technology Institute, Ispra for the acquisition, evaluation, management and storage of measurements data originating from passive neutron assay of plutonium bearing materials. The software accommodates the implementation of the NDA (Non Destructive Assay) procedures for all types of passive neutron coincidence deployed by the Euratom Safeguards Directorate, Luxembourg

Plutonium in a grassland ecosystem. [Rocky Flats Plant

Energy Technology Data Exchange (ETDEWEB)

Little, C.A.

1976-08-01

A study was made of plutonium contamination of grassland at the Rocky Flats plant northwest of Denver, Colorado. Of interest were: the definition of major plutonium-containing ecosystem compartments; the relative amounts in those compartments; how those values related to studies done in other geographical areas; whether or not the predominant isotopes, /sup 238/Pu and /sup 239/Pu, behaved differently; and what mechanisms might have allowed for the observed patterns of contamination. Samples of soil, litter, vegetation, arthropods, and small mammals were collected for Pu analysis and mass determination from each of two macroplots. Small aliquots (5 g or less) were analyzed by a rapid liquid scintillation technique and by alpha spectrometry. Of the compartments sampled, greater than 99 percent of the total plutonium was contained in the soil and the concentrations were significantly inversely correlated with distance from the contamination source, depth of the sample, and particle size of the sieved soil samples. The soil data suggested that the distribution of contamination largely resulted from physical transport processes.

Determination of Uranium plus Plutonium by Alpha spectrometry in different matrix

International Nuclear Information System (INIS)

Equillor, Hugo E.; Campos, Juan M.

2011-01-01

Usually, the determination of alpha emitters by alpha spectrometry is performed with a prior purification of each of the elements to be quantified. In this work, a methodology for the determination of uranium and plutonium isotopes as jointly described, in order to improve analytical processing times and measurement. The method includes purifying uranium and plutonium, and the subsequent electrodeposition for alpha spectrometry measurement. The technique is based on the use of TBP (tributyl phosphate) as extractant and easy to obtain reactants. It is applicable to various matrices, including water, filters and soils. In the conditions described, is applied to small aliquots of approximately 0.5 g of solid. The technique produces high quality electrodeposits. (authors) [es

Nondestructive assay of plutonium in empty stainless steel boxes by apparent mass method

International Nuclear Information System (INIS)

Agarwal, C.; Chaudhury, S.; Nathaniel, T.N.; Goswami, A.

2012-01-01

Apparent mass method (Venkataraman and Croft, Nucl Instrum Methods Phys Res A 505:527, 2003), initially standardized for the assay of Pu (Agarwal et al., J Nucl Mater 651:386, 2007) has been used to get Pu amount in empty stainless steel boxes generally used for storing and transferring plutonium oxide powders. The results have been compared with the neutron coincidence counting results and have been found to match well. The advantage of the method is that it can be used for any sample with nonstandard geometry and with uncertain source distribution. (author)

Laboratory Detective Work Identifies a Mishandling Problem in Sample Aliquoting

OpenAIRE

Zhu, Claire; Pinsky, Paul; Huang, Wen-Yi; Purdue, Mark

2014-01-01

Data from a recent ovarian cancer biomarker study using serum aliquots from the Prostate, Lung, Colorectal, and Ovarian (PLCO) Cancer Screening Trial Biorepository showed that CA125II concentrations in these aliquots were significantly lower than those previously measured in the same subjects from the same blood draw. We designed an experiment to investigate whether samples used in the study (reference study) were compromised during the aliquoting process. We measured CA125II in the “sister” ...

Measurement of plutonium oxalate in thermal neutron coincidence counters

International Nuclear Information System (INIS)

Marshall, R.S.; Erkkila, B.H.

1979-01-01

A coincidence neutron counting method has been developed for assaying batches of plutonium oxalate. Using counting data from two concentric rings of 3 He detectors, corrections are made for the effects that water has on the coincidence neutron count rate. Batches of plutonium oxalate varying from 750 to 1000 g of plutonium and from 34 to 54% water are assayed with an average accuracy of +-3%

Nondestructive assay measurements applied to reprocessing plants

International Nuclear Information System (INIS)

Ruhter, Wayne D.; Lee, R. Stephen; Ottmar, Herbert; Guardini, Sergio

1999-01-01

Nondestructive assay for reprocessing plants relies on passive gamma-ray spectrometry for plutonium isotopic and plutonium mass values of medium-to-low-density samples and holdup deposits; on active x-ray fluorescence and densitometry techniques for uranium and plutonium concentrations in solutions; on calorimetry for plutonium mass in product; and passive neutron techniques for plutonium mass in spent fuel, product, and waste. This paper will describe the radiation-based nondestructive assay techniques used to perform materials accounting measurements. The paper will also discuss nondestructive assay measurements used in inspections of reprocessing plants [ru

NDA technique for the assay of wet plutonium oxalate

International Nuclear Information System (INIS)

Marshall, R.S.; Canada, T.R.

1980-01-01

A method has been developed to quantitatively measure batches of wet plutonium oxalate. The method is based on a count of coincidence neutrons to which a correction is applied for the effects of neutron moderation by water. A therma-neutron coincidence counter (TNC) with two concentric rings of 3 He detectors provides the signal needed for the water correction. The signal is the ratio of neutron counts between the detector rings that changes with the percent of water in plutonium oxalate. To evaluate the measurement technique, 26 batches of plutonium oxalate were measured in an in-line TNC. The evaluation showed the measurements to be essentially unbiased and precise to 2.2%

Standard practice for preparation and dissolution of plutonium materials for analysis

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This practice is a compilation of dissolution techniques for plutonium materials that are applicable to the test methods used for characterizing these materials. Dissolution treatments for the major plutonium materials assayed for plutonium or analyzed for other components are listed. Aliquants of the dissolved samples are dispensed on a weight basis when one of the analyses must be highly reliable, such as plutonium assay; otherwise they are dispensed on a volume basis. 1.2 The treatments, in order of presentation, are as follows: Procedure Title Section Dissolution of Plutonium Metal with Hydrochloric Acid 9.1 Dissolution of Plutonium Metal with Sulfuric Acid 9.2 Dissolution of Plutonium Oxide and Uranium-Plutonium Mixed Oxide by the Sealed-Reflux Technique 9.3 Dissolution of Plutonium Oxide and Uranium-Plutonium Mixed Oxides by Sodium Bisulfate Fusion 9.4 Dissolution of Uranium-Plutonium Mixed Oxides and Low-Fired Plutonium Oxide in Beakers 9.5 1.3 The values stated in SI units are to be re...

Simultaneous determination of uranium and plutonium in dissolver solution of irradiated fuel, using ID-TIMS. IRP-11

International Nuclear Information System (INIS)

Shah, Raju; Sasi Bhushan, K.; Govindan, R.; Alamelu, D.; Khodade, P.S.; Aggarwal, S.K.

2007-01-01

A simple sample preparation and simultaneous analysis method to determine uranium and plutonium from dissolver solution, employing the technique of Isotope Dilution Mass spectrometry has been demonstrated. The method used, co-elusion of Uranium and Plutonium from anion exchanger column after initial elution of major part of uranium in 1:5 HNO 3 in order to reduce the initial U/Pu ratio from 1000 to about 100-200 in the co-eluted fraction. Due to the availability of variable multi-collector system, different Faraday cups were adjusted to collect the different ion intensities corresponding to the different masses, during the simultaneous analysis of Uranium and Plutonium, loaded on Re double filament assembly. 233 U and PR grade Plutonium were used as spikes to determine Uranium and Plutonium from dissolver solution of irradiated fuel from research reactor. The possibility of getting the isotopic composition of uranium from the simultaneous analysis of co-eluted purified fraction of U and Pu from spiked aliquots is also explained. (author)

The design of a high-efficiency neutron counter for waste drums to provide optimized sensitivity for plutonium assay

Energy Technology Data Exchange (ETDEWEB)

Menlove, H.O.; Beddingfield, D.H.; Pickrell, M.M. [Los Alamos National Lab., NM (United States)] [and others

1997-11-01

An advanced passive neutron counter has been designed to improve the accuracy and sensitivity for the nondestructive assay of plutonium in scrap and waste containers. The High-Efficiency Neutron Counter (HENC) was developed under a Cooperative Research Development Agreement between the Los Alamos National Laboratory and Canberra Industries. The primary goal of the development was to produce a passive assay system for 200-L drums that has detectability limits and multiplicity counting features that are superior to previous systems. A detectability limit figure of merit (FOM) was defined that included the detector efficiency, the neutron die-away time, and the detector`s active volume and density that determine the cosmic-ray background. Monte Carlo neutron calculations were performed to determine the parameters to provide an optimum FOM. The system includes the {sup 252}Cf {open_quotes}add-a-source{close_quotes} feature to improve the accuracy as well as statistical filters to reduce the cosmic-ray spallation neutron background. The final decision gave an efficiency of 32% for plutonium with a detector {sup 3}He tube volume that is significantly smaller than for previous high-efficiency systems for 200-L drums. Because of the high efficiency of the HENC, we have incorporated neutron multiplicity counting for matrix corrections for those cases where the plutonium is localized in nonuniform hydrogenous materials. The paper describes the design and performance testing of the advanced system. 5 refs., 8 figs., 3 tabs.

The design of a high-efficiency neutron counter for waste drums to provide optimized sensitivity for plutonium assay

International Nuclear Information System (INIS)

Menlove, H.O.; Beddingfield, D.H.; Pickrell, M.M.

1997-01-01

An advanced passive neutron counter has been designed to improve the accuracy and sensitivity for the nondestructive assay of plutonium in scrap and waste containers. The High-Efficiency Neutron Counter (HENC) was developed under a Cooperative Research Development Agreement between the Los Alamos National Laboratory and Canberra Industries. The primary goal of the development was to produce a passive assay system for 200-L drums that has detectability limits and multiplicity counting features that are superior to previous systems. A detectability limit figure of merit (FOM) was defined that included the detector efficiency, the neutron die-away time, and the detector's active volume and density that determine the cosmic-ray background. Monte Carlo neutron calculations were performed to determine the parameters to provide an optimum FOM. The system includes the 252 Cf open-quotes add-a-sourceclose quotes feature to improve the accuracy as well as statistical filters to reduce the cosmic-ray spallation neutron background. The final decision gave an efficiency of 32% for plutonium with a detector 3 He tube volume that is significantly smaller than for previous high-efficiency systems for 200-L drums. Because of the high efficiency of the HENC, we have incorporated neutron multiplicity counting for matrix corrections for those cases where the plutonium is localized in nonuniform hydrogenous materials. The paper describes the design and performance testing of the advanced system. 5 refs., 8 figs., 3 tabs

Solution assay instrument operations manual

International Nuclear Information System (INIS)

Li, T.K.; Marks, T.; Parker, J.L.

1983-09-01

An at-line solution assay instrument (SAI) has been developed and installed in a plutonium purification and americium recovery process area in the Los Alamos Plutonium Processing Facility. The instrument was designed for accurate, timely, and simultaneous nondestructive analysis of plutonium and americium in process solutions that have a wide range of concentrations and americium/plutonium ratios and for routine operation by process technicians who lack instrumentation background. The SAI, based on transmission-corrected, high-resolution gamma-ray spectroscopy, has two measurement stations attached to a single multichannel analyzer/computer system. To ensure the quality of assay results, the SAI has an internal measurement control program, which requires daily and weekly check runs and monitors key aspects of all assay runs. For a 25-ml sample, the assay precision is 5 g/l within a 2000-s count time

Detection and measurement of gamma-ray self-attenuation in plutonium residues

International Nuclear Information System (INIS)

Prettyman, T.H.; Foster, L.A.; Estep, R.J.

1996-01-01

A new method to correct for self-attenuation in gamma-ray assays of plutonium is presented. The underlying assumptions of the technique are based on a simple but accurate physical model of plutonium residues, particularly pyrochemical salts, in which it is assumed that the plutonium is divided into two portions, each of which can be treated separately from the standpoint of gamma-ray analysis: a portion that is in the form of plutonium metal shot; and a dilute portion that is mixed with the matrix. The performance of the technique is evaluated using assays of plutonium residues by tomographic gamma scanning at the Los Alamos Plutonium Facility. The ability of the method to detect saturation conditions is examined

Automated processing of whole blood samples into microliter aliquots of plasma.

Science.gov (United States)

Burtis, C A; Johnson, W W; Walker, W A

1988-01-01

A rotor that accepts and automatically processes a bulk aliquot of a single blood sample into multiple aliquots of plasma has been designed and built. The rotor consists of a central processing unit, which includes a disk containing eight precision-bore capillaries. By varying the internal diameters of the capillaries, aliquot volumes ranging 1 to 10 mul can be prepared. In practice, an unmeasured volume of blood is placed in a centre well, and, as the rotor begins to spin, is moved radially into a central annular ring where it is distributed into a series of processing chambers. The rotor is then spun at 3000 rpm for 10 min. When the centrifugal field is removed by slowly decreasing the rotor speed, an aliquot of plasma is withdrawn by capillary action into each of the capillary tubes. The disk containing the eight measured aliquots of plasma is subsequently removed and placed in a modifed rotor for conventional centrifugal analysis. Initial evaluation of the new rotor indicates that it is capable of producing discrete, microliter volumes of plasma with a degree of accuracy and precision approaching that of mechanical pipettes.

A simplified method for preparing micro-samples for the simultaneous isotopic analysis of uranium and plutonium

International Nuclear Information System (INIS)

Carter, J.A.; Walker, R.L.; Eby, R.E.; Pritchard, C.A.

1976-01-01

In this simplified technique a basic anion resin is employed to selectively adsorb plutonium and uranium from 8M HNO 3 solutions containing dissolved spent reactor fuels. After a few beads of the resin are equilibrated with solution, a single bead is used for establishing the isotopic composition of plutonium and uranium. The resin-bead separation essentially removes all possible isobaric interference from such elements as americium and curium and at the same time eliminates most fission-product contamination in the mass spectrometer. Small aliquots of dissolver solution that contain 10 -6 g U and 10 -8 g Pu are adequate for preparing about ten resin beads. By employing a single focusing tandem magnet-type mass spectrometer, equipped with pulse counting for ion detection, simultaneous plutonium and uranium assays are obtained. The quantity of each element per bead may be as low as 10 -9 to 10 -10 g. The carburized bead, which forms as the filament is heated, acts as a reducing point source and emits a predominance of metallic ions as compared with oxide ion emission from direct solution loadings. In addition to isotopic abundance, the technique of isotope dilution can ve coupled with the ion-exchange bead separation and used effectively for measuring the total quantity of U and Pu. The technique possesses many advantages such as reduced radiation hazards from the infinitely smaller samples, thus less shielding and transport cost for sample handling; greatly simplified chemical preparations that eliminate fission products and actinide isobaric interferences; and the minor isotopes are more precisely established. (author)

Measurement of plutonium and americium in molten salt residues

International Nuclear Information System (INIS)

Haas, F.X.; Lawless, J.L.; Herren, W.E.; Hughes, M.E.

1979-01-01

The measurement of plutonium and americium in molten salt residues using a segmented gamma-ray scanning device is described. This system was calibrated using artificially fabricated as well as process generated samples. All samples were calorimetered and the americium to plutonium content of the samples determined by gamma-ray spectroscopy. For the nine samples calorimetered thus far, no significant biases are present in the comparison of the segmented gamma-ray assay and the calorimetric assay. Estimated errors are of the order of 10 percent and is dependent on the americium to plutonium ratio determination

In-line measurement of plutonium and americium in mixed solutions

International Nuclear Information System (INIS)

Li, T.K.

1981-01-01

A solution assay instrument (SAI) has been developed at the Los Alamos National Laboratory and installed in the plutonium purification and americium recovery process area in the Los Alamos Plutonium Processing Facility. The instrument is designed for accurate, timely, and simultaneous nondestructive analysis of plutonium and americium in process solutions that have a wide range of concentrations and Am/Pu ratios. For a 25-mL sample, the assay precision is 5 g/L within a 2000-s count time

In-plant measurements of gamma-ray transmissions for precise K-edge and passive assay of plutonium concentration and isotopic abundance in product solutions at the Tokai Reprocessing Plant

International Nuclear Information System (INIS)

Asakura, Y.; Kondo, I.; Masui, J.; Shoji, K.; Russo, P.A.; Hsue, S.T.; Sprinkle, J.K. Jr.; Johnson, S.S.

1982-01-01

A field test has been carried out for more than 2 years for determination of plutonium concentration by K-edge absorption densitometry and for determination of plutonium isotopic abundance by transmission-corrected passive gamma-ray spectrometry. This system was designed and built at Los Alamos National Laboratory and installed at the Tokai reprocessing plant of the Power Reactor and Nuclear Fuel Development Corporation as a part of the Tokai Advanced Safeguards Technology Exercise (TASTEX). For K-edge measurement of plutonium concentration, the transmissions at two discrete gamma-ray energies are measured using the 121.1- and 122.1-keV gamma rays from 75 Se and 57 Co. Intensities of the plutonium passive gamma rays in the energy regions between 38 and 51 keV and between 129 and 153 keV are used for determination of the isotopic abundances. More than 200 product solution samples have been measured in a timely fashion during these 2 years. The relative precisions and accuracies of the plutonium concentration measurement are shown to be within 0.6% (1 sigma) in these applications, and those for plutonium isotopic abundances are within 3% for 238 Pu, 0.4% for 239 Pu, 1.2% for 240 Pu, 1.3% for 241 Pu, and 7% for 242 Pu. The time required is 10 min for the concentration assay, 10 min for the isotopics assay, and about 15 min for handling procedures in the laboratory

Plutonium Assay in Soil at the BRC Threshold

International Nuclear Information System (INIS)

Miller, T.

2003-01-01

The Atomic Weapons Establishment (AWE) at Aldermaston has investigated the performance of low and high-resolution gamma-ray detectors for plutonium (Pu) assay in soil at the UK Below Regulatory Concern (BRC) threshold (0.4 Bq/g above the natural background activity level). The goal was a rapid and economical technique for sorting large volumes of lightly contaminated soils into above and BRC fractions. The strategy involved utilizing the relatively high yield 60 keV emission from Am-241 ingrowth (Pu-241 daughter) and known isotopic ratios. This paper covers the determination of detector response factors for an Am-241 source positioned at various locations within a circular tray of soil. These factors were weighted, according to the relative volumes that they represent, in order to derive a uniform response factor and quantify the systematic error for non-uniform activity distributions. Detection limits and random errors were also derived from the counting data. The high-resolution detector was shown to have the best detection levels and lowest systematic and random errors. However, uncertainties for non-uniform distributions of contamination were relatively large. Hence, analyzing soils at the BRC threshold would only be feasible if contamination was well distributed throughout the soil sample being monitored. Fortunately, contaminated land at AWE is generally homogeneous and so the technique has wide applicability

Safe handling of plutonium: a panel report

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

This guide results from a meeting of a Panel of Experts held by the International Atomic Energy Agency on 8 to 12 November 1971. It is directed to workers in research laboratories handling plutonium in gram amounts. Contents: aspects of the physical and chemical properties of plutonium; metabolic features of plutonium; facility design features for safe handling of plutonium (layout of facility, working zones, decontamination room, etc.); glove boxes; health surveillance (surveillance of environment and supervision of workers); emergencies; organization. Annexes: types of glove boxes; tables; mobile ..cap alpha.. air sampler; aerosol monitor; bio-assay limits of detection; examples of contamination control monitors.

An independent method for input accountability in reprocessing plants : magnesium tracer technique for the accountability of plutonium (MAGTRAP)

International Nuclear Information System (INIS)

Mathews, C.K.; Jain, H.C.; Chitambar, S.A.; Kavimandan, V.D.; Aggarwal, S.K.

1975-01-01

A new technique 'MAGTRAP' for the measurement of the total plutonium in an accountability tank is described which does not require knowledge of either the total volume of solution in the tank or the size of the sample aliquot. The method depends on the addition of natural magnesium as a tracer and the subsequent isotope dilution of an aliquot using a spike with known 26 Mg/ 242 Pu ratio. Using only the isotopic ratios of 26 Mg/ 24 Mg and 239 Pu/ 242 Pu in the mixture, the quantity of the plutonium in the accountability tank can be calculated. In order to correct for magnesium blank, an additional measurement is required before tracer addition. The magnesium tracer technique can also be used to check the volume (or weight) calibration of the tank. Several experiments were carried out in the input accountability tank of the Fuel Reprocessing Plant at Tarapur to assess the accuracy of this method. The weight (or volume) of the solution in the tank could be measured independently with an accuracy of better than 0.5%. An experiment was also conducted to measure the total uranium in the accountability tank using MAGTRAP. The accuracy was better than 1%. The tracer technique was also used to arrive at optimum sparging times to ensure the homogeneity of the solution in the tank. Chemical procedures developed for the separation of plutonium and magnesium from dissolver solutions are also discussed. (author)

A FIFO based neutron arrival time collection technique for assay of plutonium

International Nuclear Information System (INIS)

Parthasarathy, R.; Saisubalakshmi, D.; Venkatasubramani, C.R.

2004-01-01

The system assays plutonium by counting the time correlated neutrons emitted by the spontaneous fissions of the even-even Pu isotopes in the presence of random neutron background, originating principally from (a,n) reactions in the material. The correlation technique discussed in this paper utilizes twofold neutron coincidence counting but the system is proposed to be enhanced for neutron multiplicity counting. A microcontroller based data acquisition system has been developed using a couple of fast FIFO 2kX9 bit memory ICs and a 16 bit counter for identifying time-correlated neutrons. Since the neutron pulses are arriving at a rapid rate, the incoming pulses are buffered in the FIFO and then transferred to PC by the microcontroller through the parallel port. The correlation analysis based on this time arrival information is done in the PC off-line. (author)

Smart unattended systems for plutonium safeguards

International Nuclear Information System (INIS)

Menlove, H.O.; Abhold, M.; Eccleston, G.; Puckett, J.M.

1996-01-01

Large automated facilities for fabricating plutonium fuel present both difficulties and challenges for improved accounting of nuclear materials. The traditional methods of sample measurements, requiring the transfer of the sample from the production line to the assay measurement station, are not possible in automated facilities. The robotics used for automation require special containers for nuclear material that cannot be easily removed from the production line. Safety and radiation protection considerations also require that the assay instrumentation be installed in the fuel production lines because, in general, personnel cannot be in the fuel-handling area with nuclear material during operations. Such operational constraints are common in many of the modern facilities that have been designed for fabricating and processing plutonium fuel. A bilateral safeguards agreement between the US Department of Energy (DOE) and Power Reactor and Nuclear Fuel Development Corporation (PNC) in Japan was signed to develop and implement nondestructive assay (NDA) systems to provide continuous safeguards measurements for material accountancy in the robot-automated Plutonium Fuel Fabrication Facility (PFFF). The PFFF assay systems were required to operate in unattended mode with a size and fuel mass capability to match the robotics fuel manipulators. Unattended assay systems reduce the requirement for inspector's oversight of measurement operations, reduce the inspector's workload, and improve inspection efficiencies. In addition, unattended measurements become essential when facility constraints limit the access of inspectors to the operations area during material processing. Authentication techniques were incorporated into the NDA systems so that data obtained from unattended assays could be used by independent inspectors such as the IAEA

Gamma spectrometric methods for measuring plutonium

International Nuclear Information System (INIS)

Gunnink, R.

1978-01-01

Nondestructive analyses of plutonium can be made by detecting and measuring the gamma rays emitted by a sample. Although qualitative and semiquantitative assays can be performed with relative ease, only recently have methods been developed, using computer analysis techniques, that provide quantitative results. This paper reviews some new techniques developed for measuring plutonium. The features of plutonium gamma-ray spectra are reviewed and some of the computer methods used for spectrum analysis are discussed. The discussion includes a description of a powerful computer method of unfolding complex peak multiplets that uses the standard linear least-squares techniques of data analysis. This computer method is based on the generation of response profiles for the isotopes composing a plutonium sample and requires a description of the peak positions, relative intensities, and line shapes. The principles that plutonium isotopic measurements are based on are also developed, followed by illustrations of the measurement procedures as applied to the quantitative analysis of plutonium liquid and solid samples

Measurement of Plutonium Isotopic Composition - MGA

Energy Technology Data Exchange (ETDEWEB)

Vo, Duc Ta [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-08-21

In this module, we will use the Canberra InSpector-2000 Multichannel Analyzer with a high-purity germanium detector (HPGe) and the MGA isotopic anlysis software to assay a variety of plutonium samples. The module provides an understanding of the MGA method, its attributes and limitations. You will assess the system performance by measuring a range of materials similar to those you may assay in your work. During the final verification exercise, the results from MGA will be combined with the 240Pueff results from neutron coincidence or multiplicity counters so that measurements of the plutonium mass can be compared with the operator-declared (certified) values.

Solid-phase extraction of plutonium in various oxidation states from simulated groundwater using N-benzoylphenylhydroxylamine

International Nuclear Information System (INIS)

Perevalov, S.A.; Malofeeva, G.I.; Kuzovkina, E.V.; Spivakov, B.Ya.

2013-01-01

Solid-phase extraction of plutonium in different individual and mixed oxidation states from simulated groundwater (pH 8.5) was studied. The extraction of plutonium species was carried out in a dynamic mode using DIAPAK C16 cartridges modified by N-benzoylphenylhydroxylamine (BPHA). It was shown that the extent of recovery depends on the oxidation state of plutonium. The extraction of Pu(IV) was at the level of 98-99% regardless of the volume and flow-rate of the sample solution. Pu(V) was extracted by 90-95% and 75-80% from 10- and 100-mL aliquots of the samples, respectively, whereas the extraction of Pu(VI) did not exceed 45-50%. An equimolar mixture of Pu(IV), Pu(V), and Pu(VI) was extracted by 74%. The distribution coefficients (K d ) and kinetic exchange capacities (S) of plutonium in various oxidation states were measured. It was found that during the sorption process, Pu(V) was reduced to Pu(IV) by 80-90% after an hour-long contact with the solid phase. Pu(VI) is reduced to Pu(V) by 34% and to Pu(IV) by 55%. In the case of mixed-valent solution of plutonium, only Pu(V) and Pu(IV) were found in the effluents. (author)

Genome aliquoting with double cut and join

Directory of Open Access Journals (Sweden)

Sankoff David

2008-01-01

Full Text Available Abstract Background The genome aliquoting probem is, given an observed genome A with n copies of each gene, presumed to descend from an n-way polyploidization event from an ordinary diploid genome B, followed by a history of chromosomal rearrangements, to reconstruct the identity of the original genome B'. The idea is to construct B', containing exactly one copy of each gene, so as to minimize the number of rearrangements d(A, B' ⊕ B' ⊕ ... ⊕ B' necessary to convert the observed genome B' ⊕ B' ⊕ ... ⊕ B' into A. Results In this paper we make the first attempt to define and solve the genome aliquoting problem. We present a heuristic algorithm for the problem as well the data from our experiments demonstrating its validity. Conclusion The heuristic performs well, consistently giving a non-trivial result. The question as to the existence or non-existence of an exact solution to this problem remains open.

A passive gamma scanner for estimation of plutonium in fabrication waste

International Nuclear Information System (INIS)

Venkatesan, P.P.; Burte, P.P.; Manohar, S.B.; Satya Prakash; Ramaniah, M.V.

1978-01-01

The solid plutonium wastes arising from plutonium handling laboratories and fuel fabrication facilities by their very nature (heterogeneous) are not amenable to proper sampling and hence to the standard techniques of estimation. For the proper accounting of nuclear materials a non-destructive method of waste assay is essential. A passive gamma-ray scanner developed in the Radiochemistry Division is described in the present report. The scanner detects the 384 KeV gamma complex of plutonium in a (3'' x 3'') NaI(Tl) detector. The rotation-collimation technique is used to achieve the flat response with respect to the plutonium distribution inside the waste can. The sensitivity of the scanner is 200 mg of Pu per can at 2 sigma level and 20% accuracy for a total scan time of 2000 sec. The assay results of typical waste cans and comparison of a few of these with chemical assay results are presented. This non-destructive method is fast, simple and has satisfactory accuracy. (author)

The passive nondestructive assay of the plutonium content of spent-fuel assemblies from the BN-350 fast-breeder reactor in the city of Aqtau, Kazakhstan

CERN Document Server

Lestone, J P; Rennie, J A; Sprinkle, J K; Staples, P; Grimm, K N; Hill, R N; Cherradi, I; Islam, N; Koulikov, J; Starovich, Z

2002-01-01

The International Atomic Energy Agency is presently interested in developing equipment and techniques to measure the plutonium content of breeder reactor spent-fuel assemblies located in storage ponds before they are relocated to more secure facilities. We present the first quantitative nondestructive assay of the plutonium content of fast-breeder reactor spent-fuel assemblies while still underwater in their facility storage pond. We have calibrated and installed an underwater neutron coincidence counter (Spent Fuel Coincidence Counter (SFCC)) in the BN-350 reactor spent-fuel pond in Aqtau, Kazakhstan. A procedure has been developed to convert singles and doubles (coincidence) neutron rates observed by the SFCC into the total plutonium content of a given BN-350 spent-fuel assembly. The plutonium content has been successfully determined for spent-fuel assemblies with a contact radiation level as high as approx 10 sup 5 Rads/h. Using limited facility information and multiple measurements along the length of spe...

Smart unattended systems for plutonium safeguards

International Nuclear Information System (INIS)

Menlove, H.O.; Abhold, M.; Eccleston, G.; Puckett, J.M.

1996-01-01

During the past decade, IAEA inspectors, national inspectors, and facility operators have used neutron coincidence counters and gamma-ray isotopics measurements extensively to measure the plutonium content of various forms of nuclear materials in the fuel cycle. Large automated facilities for fabricating plutonium fuel present both difficulties and challenges for improved accounting of nuclear materials. The traditional methods of sample measurements, requiring the transfer of the sample from the production line to the assay measurement station, are not possible in automated facilities. A bilateral safeguards agreement between the US Department of Energy (DOE) and Power Reactor and Nuclear Fuel Development Corporation (PNC) in Japan was signed to develop and implement nondestructive assay (NDA) systems to provide continuous safeguards measurements for material accountancy in the robot-automated Plutonium Fuel Fabrication Facility (PFFF). The PFFF assay systems were required to operate in unattended mode with a size and fuel mass capability to match the robotics fuel manipulators. Unattended assay systems reduce the requirement for inspector''s oversight of measurement operations, reduce the inspector''s workload, and improve inspection efficiencies. In addition, unattended measurements become essential when facility constraints limit the access of inspectors to the operations area during material processing. Authentication techniques were incorporated into the NDA systems so that data obtained form unattended assays could be used by independent inspectors such as the IAEA. The standardized containers and robot-controlled fuel movements in automated facilities enable more accurate nondestructive assay (NDA) measurements than are possible in conventional nonautomated facilities. The NDA instrumentation can be custom designed and optimized for the particular measurement goal in the automated facility

Radioenzymatic assay of DOPA (3,4-dihydroxyphenylalanine)

International Nuclear Information System (INIS)

Johnson, G.A.; Gren, J.M.; Kupiecki, R.

1978-01-01

We modified the single-isotope radioenzymatic assay for catecholamines [Life Sci. 21, 625(1977)] to assay 3,4-dihydroxyphenylalanine (DOPA). DOPA decarboxylase is used to convert DOPA to dopamine, which concurrently is converted to [ 3 H]-3-O-methyldopamine in the presence of catechol-O-methyltransferase and [methyl- 3 H]-S-adenosylmethionine and assayed radioenzymatically. For assay of plasma DOPA, 50 μl of untreated plasma is added directly into the incubation mixture. A duplicate mixture containing an internal standard requires a second 50-μl aliquot of plasma. Because the assay measures both DOPA and endogenous dopamine, two additional aliquots of plasma must be assayed for dopamine in the absence of the decarboxylase by the differential assay; DOPA is estimated by difference. The assay is sensitive to 25 pg (500 ng/liter of plasma). Analysis of DOPA (DOPA plus dopamine) and the concurrent differential assay of catecholamines in at least 10 samples can be done in a single working day. Plasma DOPA concentrations for 42 normotensive adults were 1430 +- 19 ng/liter (mean +- SEM). In contrast, dopamine concentrations for these same subjects averaged 23 +- 20 ng/liter. Values for the 24 women subjects (1510 +- 62 ng/liter) significantly (P = 0.04) exceeded those for the men

Statistical analysis of a LASL study of plutonium in US autopsy tissue

International Nuclear Information System (INIS)

Fox, T.; Tietjen, G.L.; McInroy, J.F.

1979-01-01

The Autopsy Tissue Program was begun in 1960. To date, tissues on 900 or more persons in 7 geographic regions have been collected and analyzed for plutonium content. The tissues generally consist of lung, liver, kidney, lymph, bone, and gonadal tissues for each individual. The original objective of the program was to determine the level of plutonium in human tissues due solely to fallout from weapons testing. The baseline thus established was to be used to evaluate future changes. From the first, this program was beset with chemical and statistical difficulties. Many factors whose effects were not recognized and not planned for were found later to be important. Privacy and ethical considerations hindered the gathering of adequate data. Since the chemists were looking for amounts of plutonium very close to background, possible contamination was a very real problem. Widely used chemical techniques introduced a host of statistical problems. The difficulties encountered touch on areas common to large data sets, unusual outlier detection methods minimum detection limits, problems with aliquot sizes, and time-trends in the data. The conclusions point out areas to which the biologists will have to devote much more careful attention than was believed

Quantifying the passive gamma signal from spent nuclear fuel in support of determining the plutonium content in spent nuclear fuel with nondestructive assay

Energy Technology Data Exchange (ETDEWEB)

Fensin, Michael L [Los Alamos National Laboratory; Tobin, Steven J [Los Alamos National Laboratory; Menlove, Howard O [Los Alamos National Laboratory; Swinhoe, Martyn T [Los Alamos National Laboratory

2009-01-01

The objective of safeguarding nuclear material is to deter diversions of significant quantities of nuclear materials by timely monitoring and detection. There are a variety of motivations for quantifying plutonium in spent fuel (SF), by means of nondestructive assay (NDA), in order to meet this goal. These motivations include the following: strengthening the capabilities of the International Atomic Energy Agencies ability to safeguard nuclear facilities, shipper/receiver difference, input accountability at reprocessing facilities and burnup credit at repositories. Many NDA techniques exist for measuring signatures from SF; however, no single NDA technique can, in isolation, quantify elemental plutonium in SF. A study has been undertaken to determine the best integrated combination of 13 NDA techniques for characterizing Pu mass in spent fuel. This paper focuses on the development of a passive gamma measurement system in support the spent fuel assay system. Gamma ray detection for fresh nuclear fuel focuses on gamma ray emissions that directly coincide with the actinides of interest to the assay. For example, the 186-keV gamma ray is generally used for {sup 235}U assay and the 384-keV complex is generally used for assaying plutonium. In spent nuclear fuel, these signatures cannot be detected as the Compton continuum created from the fission products dominates the signal in this energy range. For SF, the measured gamma signatures from key fission products ({sup 134}Cs, {sup 137}Cs, {sup 154}Eu) are used to ascertain burnup, cooling time, and fissile content information. In this paper the Monte Carlo modeling set-up for a passive gamma spent fuel assay system will be described. The set-up of the system includes a germanium detector and an ion chamber and will be used to gain passive gamma information that will be integrated into a system for determining Pu in SF. The passive gamma signal will be determined from a library of {approx} 100 assemblies that have been

Portable gamma-ray holdup and attributes measurements of high- and variable-burnup plutonium

International Nuclear Information System (INIS)

Wenz, T.R.; Russo, P.A.; Miller, M.C.; Menlove, H.O.; Takahashi, S.; Yamamoto, Y.; Aoki, I.

1991-01-01

High burnup-plutonium holdup has been assayed quantitatively by low resolution gamma-ray spectrometry. The assay was calibrated with four plutonium standards representing a range of fuel burnup and 241 Am content. Selection of a calibration standard based on its qualitative spectral similarity to gamma-ray spectra of the process material is partially responsible for the success of these holdup measurements. The spectral analysis method is based on the determination of net counts in a single spectral region of interest (ROI). However, the low-resolution gamma-ray assay signal for the high-burnup plutonium includes unknown amounts of contamination from 241 Am. For most needs, the range of calibration standards required for this selection procedure is not available. A new low-resolution gamma-ray spectral analysis procedure for assay of 239 Pu has been developed. The procedure uses the calculated isotope activity ratios and the measured net counts in three spectral ROIs to evaluate and remove the 241 Am contamination from the 239 Pu assay signal on a spectrum-by-spectrum basis. The calibration for the new procedure requires only a single plutonium standard. The procedure also provides a measure of the burnup and age attributes of holdup deposits. The new procedure has been demonstrated using portable gamma-ray spectroscopy equipment for a wide range of plutonium standards and has also been applied to the assay of 239 Pu holdup in a mixed oxide fuel fabrication facility. 10 refs., 5 figs., 3 tabs

Measurement of plutonium in spent nuclear fuel by self-induced x-ray fluorescence

Energy Technology Data Exchange (ETDEWEB)

Hoover, Andrew S [Los Alamos National Laboratory; Rudy, Cliff R [Los Alamos National Laboratory; Tobin, Steve J [Los Alamos National Laboratory; Charlton, William S [Los Alamos National Laboratory; Stafford, A [TEXAS A& M; Strohmeyer, D [TEXAS A& M; Saavadra, S [ORNL

2009-01-01

Direct measurement of the plutonium content in spent nuclear fuel is a challenging problem in non-destructive assay. The very high gamma-ray flux from fission product isotopes overwhelms the weaker gamma-ray emissions from plutonium and uranium, making passive gamma-ray measurements impossible. However, the intense fission product radiation is effective at exciting plutonium and uranium atoms, resulting in subsequent fluorescence X-ray emission. K-shell X-rays in the 100 keV energy range can escape the fuel and cladding, providing a direct signal from uranium and plutonium that can be measured with a standard germanium detector. The measured plutonium to uranium elemental ratio can be used to compute the plutonium content of the fuel. The technique can potentially provide a passive, non-destructive assay tool for determining plutonium content in spent fuel. In this paper, we discuss recent non-destructive measurements of plutonium X-ray fluorescence (XRF) signatures from pressurized water reactor spent fuel rods. We also discuss how emerging new technologies, like very high energy resolution microcalorimeter detectors, might be applied to XRF measurements.

Experimental program for development and evaluation of nondestructive assay techniques for plutonium holdup

International Nuclear Information System (INIS)

Brumbach, S.B.

1977-05-01

An outline is presented for an experimental program to develop and evaluate nondestructive assay techniques applicable to holdup measurement in plutonium-containing fuel fabrication facilities. The current state-of-the-art in holdup measurements is reviewed. Various aspects of the fuel fabrication process and the fabrication facility are considered for their potential impact on holdup measurements. The measurement techniques considered are those using gamma-ray counting, neutron counting, and temperature measurement. The advantages and disadvantages of each technique are discussed. Potential difficulties in applying the techniques to holdup measurement are identified. Experiments are proposed to determine the effects of such problems as variation in sample thickness, in sample distribution, and in background radiation. These experiments are also directed toward identification of techniques most appropriate to various applications. Also proposed are experiments to quantify the uncertainties expected for each measurement

The impact of gate width setting and gate utilization factors on plutonium assay in passive correlated neutron counting

International Nuclear Information System (INIS)

Henzlova, D.; Menlove, H.O.; Croft, S.; Favalli, A.; Santi, P.

2015-01-01

In the field of nuclear safeguards, passive neutron multiplicity counting (PNMC) is a method typically employed in non-destructive assay (NDA) of special nuclear material (SNM) for nonproliferation, verification and accountability purposes. PNMC is generally performed using a well-type thermal neutron counter and relies on the detection of correlated pairs or higher order multiplets of neutrons emitted by an assayed item. To assay SNM, a set of parameters for a given well-counter is required to link the measured multiplicity rates to the assayed item properties. Detection efficiency, die-away time, gate utilization factors (tightly connected to die-away time) as well as optimum gate width setting are among the key parameters. These parameters along with the underlying model assumptions directly affect the accuracy of the SNM assay. In this paper we examine the role of gate utilization factors and the single exponential die-away time assumption and their impact on the measurements for a range of plutonium materials. In addition, we examine the importance of item-optimized coincidence gate width setting as opposed to using a universal gate width value. Finally, the traditional PNMC based on multiplicity shift register electronics is extended to Feynman-type analysis and application of this approach to Pu mass assay is demonstrated

The impact of gate width setting and gate utilization factors on plutonium assay in passive correlated neutron counting

Energy Technology Data Exchange (ETDEWEB)

Henzlova, D., E-mail: henzlova@lanl.gov [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Menlove, H.O. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Croft, S. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Favalli, A.; Santi, P. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2015-10-11

In the field of nuclear safeguards, passive neutron multiplicity counting (PNMC) is a method typically employed in non-destructive assay (NDA) of special nuclear material (SNM) for nonproliferation, verification and accountability purposes. PNMC is generally performed using a well-type thermal neutron counter and relies on the detection of correlated pairs or higher order multiplets of neutrons emitted by an assayed item. To assay SNM, a set of parameters for a given well-counter is required to link the measured multiplicity rates to the assayed item properties. Detection efficiency, die-away time, gate utilization factors (tightly connected to die-away time) as well as optimum gate width setting are among the key parameters. These parameters along with the underlying model assumptions directly affect the accuracy of the SNM assay. In this paper we examine the role of gate utilization factors and the single exponential die-away time assumption and their impact on the measurements for a range of plutonium materials. In addition, we examine the importance of item-optimized coincidence gate width setting as opposed to using a universal gate width value. Finally, the traditional PNMC based on multiplicity shift register electronics is extended to Feynman-type analysis and application of this approach to Pu mass assay is demonstrated.

Measurement of the equivalent dose in quartz using a regenerative-dose single-aliquot protocol

International Nuclear Information System (INIS)

Murray, A.S.; Roberts, R.G.

1998-01-01

The principles behind a regenerative-dose single-aliquot protocol are outlined. It is shown for three laboratory-bleached Australian sedimentary quartz samples that the relative change in sensitivity of the optically stimulated luminescence (OSL) during a repeated measurement cycle (consisting of a dose followed by a 10 s preheat at a given temperature and then a 100 s exposure to blue/green light at 125 deg. C) is very similar to that of the 110 deg. C thermoluminescence (TL) peak measured during the preheat cycle. The absolute change in the TL sensitivity with preheat temperature is different for samples containing a natural or a regenerative dose. Furthermore, the absolute change in sensitivity in both the OSL and TL signals is non-linear with regeneration cycle, but the relative change in the OSL signal compared to the following 110 deg. C TL measurement is well approximated by a straight line. Both signals are thought to use the same luminescence centres, and so some common behaviour is not unexpected. A new regenerative-dose protocol is presented which makes use of this linear relationship to correct for sensitivity changes with regeneration cycle, and requires only one aliquot for the estimation of the equivalent dose (D e ). The protocol has been applied to quartz from nine Australian sites. To illustrate the value of the regenerative-dose single-aliquot approach, the apparent values of D e for 13 samples, containing doses of between 0.01 and 100 Gy, have been measured at various preheat temperatures of between 160 and 300 deg. C, using a single aliquot for each D e measurement. Excellent agreement is found between these single-aliquot estimates of D e and those obtained from additive-dose multiple-aliquot and single-aliquot protocols, over the entire dose range

Determination of plutonium-241 half-life by mass spectrometric measurement

International Nuclear Information System (INIS)

Hiyama, Takashi; Wada, Yukio; Onishi, Koichi

1982-01-01

Much data for Pu-241 half-life have been reported, but these values range from 13.8 years to 15.1 years depending on investigators. In order to define the half-life of Pu-241, the half-life was calculated by analyzing the mass spectrometry data obtained in the author's laboratory over the past six years on Plutonium Isotopic Standard Reference Materials prepared at the National Bureau of Standards (NBS). The sample used for this work consisted of SRM-947 and SRM-948 prepared at NBS. Before mass spectrometric analysis, the plutonium aliquot was separated from its Am-241 daughter by anion exchange chromatography, since Am-241 is not distinguished from Pu-241 in the mass spectrometer. 241 Pu/ 239 Pu and 241 Pu/ 240 Pu ratios were calculated from the values of mass spectrometric measurement. From the relation of log N to time, the half-life of Pu-241 was determined, based on the slope using a least squares fit. The half-life of Pu-241 was estimated to be 14.29+-0.15 years. (Yoshitake, I.)

Application of the luminescence single-aliquot technique for dose estimation in the Marmara Sea

International Nuclear Information System (INIS)

Tanir, Guenes; Sencan, Emine; Boeluekdemir, M. Hicabi; Tuerkoez, M. Burak; Tel, Eyuep

2005-01-01

The aim of this study is to obtain the equivalent dose, which is the important quantity for all the studies related to the use of luminescence in dating sediments. Recent advances in luminescence dating have led to increasing application of the technique to sediment from the depositional environmental samples. The sample used in this study is the active main fault sample that was collected from the Sea of Marmara in NW Turkey. Equivalent dose was measured using both the multiple-aliquots and the single-aliquot techniques. In this study single aliquot regeneration on additive dose (SARA) procedure was also used. The result obtained was not in agreement with the results evaluated from the multiple-aliquots procedure. So a simple modification was suggested for SARA procedure. In our modified procedure the calculated dose (D) values were obtained by using the additive dose protocol instead of regeneration protocol

Plutonium fires; Incendies de plutonium

Energy Technology Data Exchange (ETDEWEB)

Mestre, E.

1959-06-23

The author reports an information survey on accidents which occurred when handling plutonium. He first addresses accidents reported in documents. He indicates the circumstances and consequences of these accidents (explosion in glove boxes, fires of plutonium chips, plutonium fire followed by filter destruction, explosion during plutonium chip dissolution followed by chip fire). He describes hazards associated with plutonium fires: atmosphere and surface contamination, criticality. The author gives some advices to avoid plutonium fires. These advices concern electric installations, the use of flammable solvents, general cautions associated with plutonium handling, venting and filtration. He finally describes how to fight plutonium fires, and measures to be taken after the fire (staff contamination control, atmosphere control)

Stop plutonium; Stop plutonium

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-02-01

This press document aims to inform the public on the hazards bound to the plutonium exploitation in France and especially the plutonium transport. The first part is a technical presentation of the plutonium and the MOX (Mixed Oxide Fuel). The second part presents the installation of the plutonium industry in France. The third part is devoted to the plutonium convoys safety. The highlight is done on the problem of the leak of ''secret'' of such transports. (A.L.B.)

Study comparing human papillomavirus (HPV) real-time multiplex PCR and Hybrid Capture II INNO-LiPA v2 HPV genotyping PCR assays

DEFF Research Database (Denmark)

Iftner, Thomas; Germ, Liesje; Swoyer, Ryan

2009-01-01

methods has not been well characterized. Clinically, cytology is used to establish possible HPV infection. We evaluated the sensitivity and specificity of HPV multiplex PCR assays compared to those of the testing scheme of the Hybrid Capture II (HCII) assay followed by an HPV PCR/line hybridization assay...... (HCII-LiPA v2). SurePath residual samples were split into two aliquots. One aliquot was subjected to HCII testing followed by DNA extraction and LiPA v2 genotyping. The second aliquot was shipped to a second laboratory, where DNA was extracted and HPV multiplex PCR testing was performed. Comparisons...... were evaluated for 15 HPV types common in both assays. A slightly higher proportion of samples tested positive by the HPV multiplex PCR than by the HCII-LiPA v2 assay. The sensitivities of the multiplex PCR assay relative to those of the HCII-LiPA v2 assay for HPV types 6, 11, 16, and 18, for example...

Comparison of different methods of determining plutonium content and isotopic composition

International Nuclear Information System (INIS)

Anon.

1986-01-01

At Rockwell Hanford Operations, several different methods are used to determine plutonium content and isotopic composition. These include alpha particle energy analysis, calorimetry/gamma-ray analysis, mass spectrometry, and low energy gamma-ray assay. Each is used in a process control environment and has its advantages and disadvantages in terms of sample matrix, sample preparation, concentration, error ranges, detection limits, and turn around time. Of the methods discussed, special attention is paid to the Plutonium Isotopics Solution Counter, a low energy gamma-ray assay system designed to provide plutonium and americium content and isotopic composition of Pu-238 through Pu-241 and Am-241. It is qualitatively and quantitatively compared to the other methods. A brief description of sample types which the Solution Counter analyzes is presented

Non-destructive assay system for uranium and plutonium in reprocessing input solutions. Hybrid K-edge/XRF Densitometer. JASPAS JC-11 final report

International Nuclear Information System (INIS)

Surugaya, N.; Abe, K.; Kurosawa, A.; Ikeda, H.; Kuno, Y.

1997-05-01

As a part of JASPAS programme, a non-radioactive assay system for the accountability of uranium and plutonium in input dissolver solutions of a spent fuel reprocessing plant, called Hybrid K-edge/XRF Densitometer, has been developed at the Tokai Reprocessing plant (TRP) since 1991. The instrument is the one of the hybrid type combined K-edge densitometry (KED) and X-ray fluorescence (XRF) analysis. The KED is used to determine the uranium concentration and the XRF is used to determine the U/Pu ratio. These results give the plutonium concentration in consequence. It is considered that the instrument has the capability of timely on-site verification for input accountancy. The instrument had been installed in the analytical hot cell at the TRP and the experiments comparing with Isotope Dilution Mass Spectrometry (IDMS) method have been carried out. As the results of measurements for the actual input solutions in the acceptance and performance tests, it was typically confirmed that the precision for determining uranium concentration by the KED was within 0.2%, whereas the XRF for plutonium performed within 0.7%. This final report summarizes the design information and performance data so as to end the JASPAS programme. (author)

Calibration of UFBC counters and their performance in the assay of large mass plutonium samples

International Nuclear Information System (INIS)

Verrecchia, G.P.D.; Smith, B.G.R.; Cranston, R.

1991-01-01

This paper reports on the cross-calibration of four Universal Fast Breeder reactor assembly coincidence (UFBC) counters using multi-can containers of Plutonium oxide powders with masses between 2 and 12 Kg of plutonium and a parametric study on the sensitivity of the detector response to the positioning or removal and substitution of the material with empty cans. The paper also reports on the performance of the UFBC for routine measurements on large mass, multi-can containers of plutonium oxide powders and compares the results to experience previously obtained in the measurement of fast reactor type fuel assemblies in the mass range 2 to 16 Kg of plutonium

Preliminary report of the comparison of multiple non-destructive assay techniques on LANL Plutonium Facility waste drums

International Nuclear Information System (INIS)

Bonner, C.; Schanfein, M.; Estep, R.

1999-01-01

Prior to disposal, nuclear waste must be accurately characterized to identify and quantify the radioactive content. The DOE Complex faces the daunting task of measuring nuclear material with both a wide range of masses and matrices. Similarly daunting can be the selection of a non-destructive assay (NDA) technique(s) to efficiently perform the quantitative assay over the entire waste population. In fulfilling its role of a DOE Defense Programs nuclear User Facility/Technology Development Center, the Los Alamos National Laboratory Plutonium Facility recently tested three commercially built and owned, mobile nondestructive assay (NDA) systems with special nuclear materials (SNM). Two independent commercial companies financed the testing of their three mobile NDA systems at the site. Contained within a single trailer is Canberra Industries segmented gamma scanner/waste assay system (SGS/WAS) and neutron waste drum assay system (WDAS). The third system is a BNFL Instruments Inc. (formerly known as Pajarito Scientific Corporation) differential die-away imaging passive/active neutron (IPAN) counter. In an effort to increase the value of this comparison, additional NDA techniques at LANL were also used to measure these same drums. These are comprised of three tomographic gamma scanners (one mobile unit and two stationary) and one developmental differential die-away system. Although not certified standards, the authors hope that such a comparison will provide valuable data for those considering these different NDA techniques to measure their waste as well as the developers of the techniques

Performance evaluation of indigenous controlled potential coulometer for the determination of uranium and plutonium

International Nuclear Information System (INIS)

Sharma, H.S.; Jisha, V.; Noronha, D.M.; Sharma, M.K.; Aggarwal, S.K.

2007-09-01

We have carried out performance evaluation of indigenously manufactured controlled potential coulometer for the determination of uranium and plutonium respectively in Rb 2 U(SO 4 ) 3 and K 4 Pu(SO 4 ) 4 chemical assay standards. The coulometric results obtained on uranium determination showed an insignificant difference as compared with the biamperometric results at 95% and 99.9% confidence levels while for plutonium determination showed a difference of -0.4% at 95% with respect to expected value. The results obtained show that indigenous coulometer is suitable for uranium and plutonium determination in chemical assay standards. (author)

Experiences of shipper-receiver differences in plutonium oxide transactions

International Nuclear Information System (INIS)

Swinburn, K.A.; McGowan, I.R.

1976-01-01

Plutonium oxide has the property of absorbing moisture, carbon dioxide etc., to the extent that it is necessary to take special steps to determine the plutonium content in such a way as to avoid shipper-receiver differences. This paper describes a method used internationally for several years for correcting for any absorption. The consignee witnesses the weighing of the bulk material (D kg) at the time of blending and sampling at the consignor's Works, and also the weighing of the sample (C g). Immediately before analysis the sample is reweighed (B g) and assayed for plutonium (A%). The weight of plutonium is then (A/100)x(B/C)xD kg. The accepted weight is the average between consignor's and consignee's figures after both have used the formula indicated. It goes on to give actual assay and fissile content figures obtained by BNFL and its consignees for the international transactions already referred to, and concludes that the method of approach results cumulatively in a negligible shipper-receiver difference. Individual transactions are shown to be commercially acceptable and, it is considered, also acceptable for safeguards purposes. It is suggested that for safeguarded material the safeguards inspectors might also be able to be present at, and themselves witness, the blending, sampling and weighing operations, and at the same time take their own samples for analysis. It is further suggested that the principle could be extended to accoutancy for plutonium in plutonium nitrate solutions provided leakage does not occur from the sample vials. (author)

Comparison of different methods of determining plutonium content and isotopic composition

International Nuclear Information System (INIS)

Dowell, M.R.W.

1985-05-01

At Rockwell Hanford Operations, several different methods are used to determine plutonium content and isotopic composition. These include alpha particle energy analysis, calorimetry/gamma-ray analysis, mass spectrometry, and low energy ray assay. Each is used in a process control environment and has its advantages and disadvantages in terms of sample matrix, sample preparation, concentration, error ranges, detection limits, and turn around time. Of the methods discussed, special attention is paid to the Plutonium Isotopics Solution Counter, a low energy gamma ray assay system designed to provide plutonium and americium content and isotopic composition of Pu-238 through Pu-241 and Am-241. It is qualitatively and quantitatively compared to the other methods. A brief description of sample types which the Solution Counter analyzes is presented. 4 refs., 4 tabs

Rapid and Automated Determination of Plutonium and Neptunium in Environmental Samples

DEFF Research Database (Denmark)

Qiao, Jixin

This thesis presents improved analytical methods for rapid and automated determination of plutonium and neptunium in environmental samples using sequential injection (SI) based chromatography and inductively coupled plasma mass spectrometry (ICP-MS). The progress of methodology development...... and optimization for rapid determination of plutonium in environmental samples using SIextraction chromatography prior to inductively coupled plasma mass spectrometry (Paper III); (3) Development of an SI-chromatographic method for simultaneous determination of plutonium and neptunium in environmental samples...... for rapid and simultaneous determination of plutonium and neptunium within an SI system (Paper VI). The results demonstrate that the developed methods in this study are reliable and efficient for accurate assays of trace levels of plutonium and neptunium as demanded in different situations including...

On-line monitoring of low-level plutonium concentrations

International Nuclear Information System (INIS)

Hofstetter, K.J.; Huff, G.A.; Rebagay, T.V.

1979-10-01

An on-line monitor has been developed to assay plutonium in nitric acid solutions. The performance of the monitor has been assessed by a laboratory experimentation program using solutions with plutonium concentrations from 0.1 to 10 g/l. These conditions are typical of the plutonium solutions in an input stream to a plutonium-purification cycle in a reprocessing plant following uranium/plutonium partitioning. The monitoring system can be fully automated and shows great promise for detecting and quantifying plutonium in situ, thus minimizing the reliance on traditional sampling and laboratory-analysis techniques. The total concentration and isotopic abundance of plutonium are determined by measuring the absolute intensities of the low-energy gamma rays characteristics of 238 Pu, 239 Pu, and 240 Pu nuclides by direct gamma-ray spectroscopy and computer analysis of the spectral data. The addition of a monitoring system of this type to the input stream of a plutonium-purification cycle along with other suitable monitors on the waste streams and on the product stream provides the basis for a near real-time materials control and inventory system. Results of the laboratory-evaluation program employing plutonium in solutions with isotopic compositions typical of those involved in processing light water reactor fuels are presented. The detailed design of a monitoring cell and detection system is given. The precision and accuracy of the results relative to those measured by mass spectrometry and controlled potential coulometry are also summarized

CONVERSION OF PLUTONIUM TRIFLUORIDE TO PLUTONIUM TETRAFLUORIDE

Science.gov (United States)

Fried, S.; Davidson, N.R.

1957-09-10

A large proportion of the trifluoride of plutonium can be converted, in the absence of hydrogen fluoride, to the tetrafiuoride of plutonium. This is done by heating plutonium trifluoride with oxygen at temperatures between 250 and 900 deg C. The trifiuoride of plutonium reacts with oxygen to form plutonium tetrafluoride and plutonium oxide, in a ratio of about 3 to 1. In the presence of moisture, plutonium tetrafluoride tends to hydrolyze at elevated temperatures and therefore it is desirable to have the process take place under anhydrous conditions.

Rapid screening method for plutonium in mixed waste samples

International Nuclear Information System (INIS)

Somers, W.; Culp, T.; Miller, R.

1987-01-01

A waste stream sampling program was undertaken to determine those waste streams which contained hazardous constituents, and would therefore be regulated as a hazardous waste under the Resource Conservation and Recovery Act. The waste streams also had the potential of containing radioactive material, either plutonium, americium, or depleted uranium. Because of the potential for contamination with radioactive material, a method of rapidly screening the liquid samples for radioactive material was required. A counting technique was devised to count a small aliquot of a sample, determine plutonium concentration, and allow the sample to be shipped the same day they were collected. This technique utilized the low energy photons (x-rays) that accompany α decay. This direct, non-destructive x-ray analysis was applied to quantitatively determine Pu-239 concentrations in industrial samples. Samples contained a Pu-239, Am-241 mixture; the ratio and/or concentrations of these two radionuclides was not constant. A computer program was designed and implemented to calculate Pu-239 activity and concentration (g/ml) using the 59.5 keV Am-241 peak to determine Am-241's contribution to the 17 keV region. Am's contribution was subtracted, yielding net counts in the 17 keV region due to Pu. 2 figs., 1 tab

Minutes of the 28th Annual Plutonium Sample Exchange Meeting. Part II: metal sample exchange

International Nuclear Information System (INIS)

1984-01-01

Contents of this publication include the following list of participating laboratories; agenda; attendees; minutes of October 25 and 26 meeting; and handout materials supplied by speakers. The handout materials cover the following: statistics and reporting; plutonium - chemical assay 100% minus impurities; americium neptunium, uranium, carbon and iron data; emission spectroscopy data; plutonium metal sample exchange; the calorimetry sample exchange; chlorine determination in plutonium metal using phyrohydrolysis; spectrophotometric determination of 238-plutonium in oxide; plutonium measurement capabilities at the Savannah River Plant; and robotics in radiochemical laboratory

A neutron well counter for plutonium assay in 200 l waste drums

International Nuclear Information System (INIS)

Eyrich, W.; Kuechle, M.; Shafiee, M.

1979-05-01

A neutron well counter is briefly described which will be used for monitoring the plutonium content of 200 l barrels in the waste treatment plant of the Kernforschungszentrum Karlsruhe. Measurements on simulated waste were made to study the influence of matrix material and non-homogeneous plutonium distribution. The variation in detection efficiency could be reduced from 28% to 10% when the signals from inner and outer neutron detectors in the polyethylene annulus are counted separately and a correction is applied, using this information. This method is superior to the source addition technique. Coincidence counting shows a larger variation which could not be reduced to below 18%. (orig.) [de

Error variation in OSL palaeodose estimates from single aliquots of quartz: a factorial experiment

International Nuclear Information System (INIS)

Galbraith, R.F.; Roberts, R.G.; Yoshida, H.

2005-01-01

We use a factorial experiment to study systematic and random differences between measured OSL palaeodoses for a variety of quartz samples. These include samples that have absorbed either a large or small natural or laboratory-induced radiation dose, either with or without prior heating or bleaching. The systematic factors studied are the size of the test dose, the preheat temperature and the number of quartz grains in each multi-grain aliquot. Palaeodoses were estimated using a single-aliquot regenerative-dose protocol. The main parameter of interest is the amount of random variation, over and above that due to photon counting statistics, to be expected between estimates from aliquots that have received the same radiation dose. This over-dispersion is generally larger for natural samples than for artificially bleached ones, and it varies from about 1% in the most favourable cases to about 18% for small aliquots of a sample that had received a natural dose of about 46 Gy. The latter is comparable to the over-dispersion reported for single grains of natural quartz that are thought to have been well-bleached at the time of deposition. The factorial experiment also revealed a number of systematic effects. In particular, measured palaeodoses using a preheat temperature of 260 deg. C were systematically lower than those using 180 deg. C, by up to about 5% in some cases

Plutonium in nature; Le plutonium dans la nature

Energy Technology Data Exchange (ETDEWEB)

Madic, C.

1994-12-31

Plutonium in nature comes from natural sources and anthropogenic ones. Plutonium at the earth surface comes principally from anthropogenic sources. It is easily detectable in environment. The plutonium behaviour in environment is complex. It seems necessary for the future to reduce releases in environment, to improve predictive models of plutonium behaviour in geosphere, to precise biological impact of anthropogenic plutonium releases.

Rapid assay of plutonium in soils by passive L x-ray counting

International Nuclear Information System (INIS)

Gehrke, R.J.; Putnam, M.H.; Goodwin, S.G.; Kynaston, R.L.

1992-05-01

A technique has been developed to rapidly measure the presence of plutonium in soils, filters, smears, and glass waste forms by measuring the uranium L-shell x-ray emissions associated with the decay of plutonium. In addition, the technique can simultaneously acquire spectra of samples and automatically analyze them for the amount of americium, and gamma-ray emitting activation and fission products present. The samples are counted with a large area, thin-window, n-type Ge spectrometer which is equally efficient for the detection of low energy x-rays (>10 key), as well as high-energy gamma rays (>1 MeV). A 8192-channel analyzer is used to acquire the entire photon spectrum at one time. A dual-energy, time-tagged pulser, that is injected into the test input of the preamplifier to monitor the energy scale, detector resolution, and pulse pile-up will be installed in FY-92. The L x-ray portion of each spectrum is analyzed by a linear least-squares spectral fitting technique originally developed for the analysis of spectra from NaI(Tl) detectors. The gamma-ray portion of each spectrum is analyzed by a standard Ge gamma-ray analysis package. Detection limits (also referred to as lower limits of detection) for plutonium in contaminated soils that have been achieved by this technique are reported

MCNP efficiency calculations of INEEL passive active neutron assay system for simulated TRU waste assays

International Nuclear Information System (INIS)

Yoon, W.Y.; Meachum, T.R.; Blackwood, L.G.; Harker, Y.D.

2000-01-01

The Idaho National Engineering and Environmental Laboratory Stored Waste Examination Pilot Plant (SWEPP) passive active neutron (PAN) radioassay system is used to certify transuranic (TRU) waste drums in terms of quantifying plutonium and other TRU element activities. Depending on the waste form involved, significant systematic and random errors need quantification in addition to the counting statistics. To determine the total uncertainty of the radioassay results, a statistical sampling and verification approach has been developed. In this approach, the total performance of the PAN nondestructive assay system is simulated using the computer models of the assay system, and the resultant output is compared with the known input to assess the total uncertainty. The supporting steps in performing the uncertainty analysis for the passive assay measurements in particular are as follows: (1) Create simulated waste drums and associated conditions; (2) Simulate measurements to determine the basic counting data that would be produced by the PAN assay system under the conditions specified; and (3) Apply the PAN assay system analysis algorithm to the set of counting data produced by simulating measurements to determine the measured plutonium mass. The validity of this simulation approach was verified by comparing simulated output against results from actual measurements using known plutonium sources and surrogate waste drums. The computer simulation of the PAN system performance uses the Monte Carlo N-Particle (MCNP) Code System to produce a neutron transport calculation for a simulated waste drum. Specifically, the passive system uses the neutron coincidence counting technique, utilizing the spontaneous fission of 240 Pu. MCNP application to the SWEPP PAN assay system uncertainty analysis has been very useful for a variety of waste types contained in 208-ell drums measured by a passive radioassay system. The application of MCNP to the active radioassay system is also feasible

Development of techniques for measuring plutonium contents in TRU wastes by NDA methods

International Nuclear Information System (INIS)

Matsubayashi, Toshiyuki; Kuwana, Katsumi; Morita, Tomio; Izuhara, Shigeomi; Suzuki, Masahiro

1983-01-01

In order to develop a technique for measuring the amount of plutonium in plutonium-contaminated (TRU) wastes, a passive gamma method was selected from many candidate methods, and examined for the suitability by applying the method to low density wastes. A segmented gamma scanner was used for the experiment. The instrument is composed mainly of a Ge(Li) detector, multichannel analyser, data processing system, turntable and transmission radiation source of (75)Se. A sham waste was prepared by adding plutonium oxide powder as a radiation source to waste matrix in a 20-1 carton box. The sham waste was put on the turntable, and the detector was set at 50 cm distance from the center of the turntable. 414 keV gamma ray emitted from (239)Pu was utilized for the assay of plutonium in the experiment. The effects of combustible (paper) waste matrix, organic chlorinated material matrix, and the distribution of plutonium source in a box on the count rate were examined, and it was concluded that 1) about 10 mg of (239)Pu contained in both matrices should be assayed by the passive gamma method, 2) 50 mg of (239) Pu was measured at 30 % confidence level with 2000 sec measuring time, 3) the effect of distribution of plutonium in a waste was able to be reduced to a value of less than 15 % by rotating the waste on the turntable. (Yoshitake, I.)

Plutonium

International Nuclear Information System (INIS)

Watson, G.M.

1976-01-01

Discovery of the neutron made it easy to create elements which do not exist in nature. One of these is plutonium, and its isotope with mass number 239 has nuclear properties which make it both a good fuel for nuclear power reactors and a good explosive for nuclear weapons. Since it was discovered during a war the latter characteristic was put to use, but it is now evident that use of plutonium in a particular kind of nuclear reactor, the fast breeder reactor, will allow the world's resources of uranium to last for millennia as a major source of energy. Plutonium is very radiotoxic, resembling radium in this respect. Therefore the widespread introduction of fast breeder reactors to meet energy demands can be contemplated only after assurances on two points; that adequate control of the radiological hazard resulting from the handling of very large amounts of plutonium can be guaranteed, and that diversion of plutonium to illicit use can be prevented. The problems exist to a lesser degree already, since all types of nuclear reactor produce some plutonium. Some plutonium has already been dispersed in the environment, the bulk of it from atmospheric tests of nuclear weapons. (author)

Plutonium isotopic determination from gamma-ray spectra

International Nuclear Information System (INIS)

Skourikhine, A.N.; Strittmatter, R.B.; Zardecki, A.

1998-01-01

The use of low- and medium-resolution room-temperature detectors for the nondestructive assay of nuclear materials has widespread applications to the safeguarding of nuclear materials. The challenge to using these detectors is the inherent difficulty of the spectral analysis to determine the amount of specific nuclear materials in the measured samples. This is especially true for extracting plutonium isotopic content from low- and medium-resolution spectral lines that are not well resolved. In this paper, neural networks trained by stochastic and singular value decomposition algorithms are applied to retrieve the plutonium isotopic content from a simulated NaI spectra. The simulated sample consists of isotopes 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu, and 241 Am. It is demonstrated that the neutral network optimized by singular value decomposition (SVD) and stochastic training algorithms is capable of estimating plutonium content consistently resulting in an average error much smaller than the error previously reported

Preparation of drop deposited plutonium sources on porcelain support

International Nuclear Information System (INIS)

Miguel, M.; Delle Site, A.; Deron, S.; Raab, W.; Swietly, H.

1984-01-01

Plutonium alpha spectrometry is of interest in safeguards verification, particular for the characterization of test materials for calorimetric assay of plutonium products and for the assay of spent fuel solutions by isotope dilution alpha spectrometry. Such measurements require 0.1-0.3% precision and accuracy in 238 Pu isotopic assay. The present paper reports experience with an alpha spectrometry procedure intended for routine measurements. Sources of excellent quality are prepared very simply and rapidly by drop deposition on porcelain supports. The method of preparation is described which readily produces sources with resolutions of 16 keV (fwhm). The effect of various measurement parameters, tail correction, 241 Am separation and in-growth, are presented. Results are compared with those of mass spectrometry. The relative bias between the 238 Pu/ 239 Pu isotopic ratio measured by the two techniques is of the order of +- 0.5%, with a standard deviation of 1.0%. The performance of alpha spectrometry is at present limited by the quality of the 241 Am separation. (orig.)

Comparison of NDA and DA measurement techniques for excess plutonium powders at the Hanford Site: Statistical design and heterogeneity testing

International Nuclear Information System (INIS)

Welsh, T.L.; McRae, L.P.; Delegard, C.H.; Liebetrau, A.M.; Johnson, W.C.; Theis, W.; Lemaire, R.J.; Xiao, J.

1995-06-01

Quantitative physical measurements are a n component of the International Atomic Energy Agency (IAEA) nuclear material m ampersand guards verification regime. In December 1994, LA.FA safeguards were initiated on an inventory of excess plutonium powder items at the Plutonium Finishing Plant, Vault 3, on the US Department of Energy's Hanford Site. The material originl from the US nuclear weapons complex. The diversity of the chemical form and the heterogenous physical form of this inventory were anticipated to challenge the precision and accuracy of quantitative destructive analytical techniques. A sampling design was used to estimate the degree of heterogeneity of the plutonium content of a variety of inventory items. Plutonium concentration, the item net weight, and the 240 Pu content were among the variables considered in the design. Samples were obtained from randomly selected location within each item. Each sample was divided into aliquots and analyzed chemically. Operator measurements by calorimetry and IAEA measurements by coincident neutron nondestructive analysis also were performed for the initial physical inventory verification materials and similar items not yet under IAEA safeguards. The heterogeneity testing has confirmed that part of the material is indeed significantly heterogeneous; this means that precautionary measures must be taken to obtain representative samples for destructive analysis. In addition, the sampling variability due to material heterogeneity was found to be comparable with, or greater than, the variability of the operator's calorimetric measurements

Plutonium Finishing Plant. Interim plutonium stabilization engineering study

Energy Technology Data Exchange (ETDEWEB)

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J. [Pacific Northwest Lab., Richland, WA (United States); Nass, R. [Nuclear Fuel Services, Inc. (United States)

1995-08-01

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage.

Plutonium Finishing Plant. Interim plutonium stabilization engineering study

International Nuclear Information System (INIS)

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J.; Nass, R.

1995-08-01

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage

Stop plutonium

International Nuclear Information System (INIS)

2003-02-01

This press document aims to inform the public on the hazards bound to the plutonium exploitation in France and especially the plutonium transport. The first part is a technical presentation of the plutonium and the MOX (Mixed Oxide Fuel). The second part presents the installation of the plutonium industry in France. The third part is devoted to the plutonium convoys safety. The highlight is done on the problem of the leak of ''secret'' of such transports. (A.L.B.)

Problems and progress in the preparation of sources for the alpha spectrometry of plutonium

International Nuclear Information System (INIS)

Miguel, M.; Deron, S.; Swietly, H.; Heinonen, O.J.

1981-01-01

The interpretation of non-destructive measurements of plutonium materials require more accurate determinations of the isotopic abundance of Pu-238 than conventional chemical assays. The requirements of calorimetry, passive neutron and conventional chemical assays are presented and compared. When Pu-238 is measured by alpha spectrometry, these requirements define how well the plutonium must be separated from americium, and what should be the accuracy of the spectrometry. The latter can strongly depend upon the resolution of the alpha spectrum. The authors describe a procedure to produce sources by drop deposition which ensure a resolution of 17 keV with commercial instrumentation

Neutron Based Non-Destructive Assay (NDA) Measurement Systems for Safeguard

Energy Technology Data Exchange (ETDEWEB)

Swinhoe, Martyn Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-21

The objectives of this project are to introduce the assay methods for plutonium measurements using the HLNC; introduce the assay method for bulk uranium measurements using the AWCC; and introduce the assay method for fuel assembly measurements using the UNCL.

Inventory calculations in sediment samples with heterogeneous plutonium activity distribution

International Nuclear Information System (INIS)

Eriksson, M.; Dahlgaard, H.

2002-01-01

A method to determine the total inventory of a heterogeneously distributed contamination of marine sediments is described. The study site is the Bylot Sound off the Thule Airbase, NW Greenland, where marine sediments became contaminated with plutonium in 1968 after a nuclear weapons accident. The calculation is based on a gamma spectrometric screening of the 241 Am concentration in 450 one-gram aliquots from 6 sediment cores. A Monte Carlo programme then simulates a probable distribution of the activity, and based on that, a total inventory is estimated by integrating a double exponential function. The present data indicate a total inventory around 3.5 kg, which is 7 times higher than earlier estimates (0.5 kg). The difference is partly explained by the inclusion of hot particles in the present calculation. A large uncertainty is connected to this estimate, and it should be regarded as preliminary. (au)

Reduction of bias in neutron multiplicity assay using a weighted point model

Energy Technology Data Exchange (ETDEWEB)

Geist, W. H. (William H.); Krick, M. S. (Merlyn S.); Mayo, D. R. (Douglas R.)

2004-01-01

Accurate assay of most common plutonium samples was the development goal for the nondestructive assay technique of neutron multiplicity counting. Over the past 20 years the technique has been proven for relatively pure oxides and small metal items. Unfortunately, the technique results in large biases when assaying large metal items. Limiting assumptions, such as unifoh multiplication, in the point model used to derive the multiplicity equations causes these biases for large dense items. A weighted point model has been developed to overcome some of the limitations in the standard point model. Weighting factors are detemiined from Monte Carlo calculations using the MCNPX code. Monte Carlo calculations give the dependence of the weighting factors on sample mass and geometry, and simulated assays using Monte Carlo give the theoretical accuracy of the weighted-point-model assay. Measured multiplicity data evaluated with both the standard and weighted point models are compared to reference values to give the experimental accuracy of the assay. Initial results show significant promise for the weighted point model in reducing or eliminating biases in the neutron multiplicity assay of metal items. The negative biases observed in the assay of plutonium metal samples are caused by variations in the neutron multiplication for neutrons originating in various locations in the sample. The bias depends on the mass and shape of the sample and depends on the amount and energy distribution of the ({alpha},n) neutrons in the sample. When the standard point model is used, this variable-multiplication bias overestimates the multiplication and alpha values of the sample, and underestimates the plutonium mass. The weighted point model potentially can provide assay accuracy of {approx}2% (1 {sigma}) for cylindrical plutonium metal samples < 4 kg with {alpha} < 1 without knowing the exact shape of the samples, provided that the ({alpha},n) source is uniformly distributed throughout the

New automated pellet/powder assay system

International Nuclear Information System (INIS)

Olsen, R.N.

1975-01-01

This paper discusses an automated, high precision, pellet/ powder assay system. The system is an active assay system using a small isotopic neutron source and a coincidence detection system. The handling of the pellet powder samples has been automated and a programmable calculator has been integrated into the system to provide control and data analysis. The versatile system can assay uranium or plutonium in either active or passive modes

Determination of plutonium in pure plutonium nitrate solutions - Gravimetric method

International Nuclear Information System (INIS)

1987-01-01

This International Standard specifies a precise and accurate gravimetric method for determining the concentration of plutonium in pure plutonium nitrate solutions and reference solutions, containing between 100 and 300 g of plutonium per litre, in a nitric acid medium. The weighed portion of the plutonium nitrate is treated with sulfuric acid and evaporated to dryness. The plutonium sulfate is decomposed and formed to oxide by heating in air. The oxide is ignited in air at 1200 to 1250 deg. C and weighed as stoichiometric plutonium dioxide, which is stable and non-hygroscopic

Precipitation of plutonium (III) oxalate and calcination to plutonium oxide

International Nuclear Information System (INIS)

Esteban, A.; Orosco, E.H.; Cassaniti, P.; Greco, L.; Adelfang, P.

1989-01-01

The plutonium based fuel fabrication requires the conversion of the plutonium nitrate solution from nuclear fuel reprocessing into pure PuO2. The conversion method based on the precipitation of plutonium (III) oxalate and subsequent calcination has been studied in detail. In this procedure, plutonium (III) oxalate is precipitated, at room temperature, by the slow addition of 1M oxalic acid to the feed solution, containing from 5-100 g/l of plutonium in 1M nitric acid. Before precipitation, the plutonium is adjusted to trivalent state by addition of 1M ascorbic acid in the presence of an oxidation inhibitor such as hydrazine. Finally, the precipitate is calcinated at 700 deg C to obtain PuO2. A flowsheet is proposed in this paper including: a) A study about the conditions to adjust the plutonium valence. b) Solubility data of plutonium (III) oxalate and measurements of plutonium losses to the filtrate and wash solution. c) Characterization of the obtained products. Plutonium (III) oxalate has several potential advantages over similar conversion processes. These include: 1) Formation of small particle sizes powder with good pellets fabrication characteristics. 2) The process is rather insensitive to most process variables, except nitric acid concentration. 3) Ambient temperature operations. 4) The losses of plutonium to the filtrate are less than in other conversion processes. (Author) [es

A single-aliquot OSL protocol using bracketing regenerative doses to accurately determine equivalent doses in quartz

CERN Document Server

Folz, E

1999-01-01

In most cases, sediments show inherent heterogeneity in their luminescence behaviours and bleaching histories, and identical aliquots are not available: single-aliquot determination of the equivalent dose (ED) is then the approach of choice and the advantages of using regenerative protocols are outlined. Experiments on five laboratory bleached and dosed quartz samples, following the protocol described by Murray and Roberts (1998. Measurement of the equivalent dose in quartz using a regenerative-dose single aliquot protocol. Radiation Measurements 27, 171-184), showed the hazards of using a single regeneration dose: a 10% variation in the regenerative dose yielded some equivalent dose estimates that differed from the expected value by more than 5%. A protocol is proposed that allows the use of different regenerative doses to bracket the estimated equivalent dose. The measured ED is found to be in excellent agreement with the known value when the main regeneration dose is within 10% of the true equivalent dose.

A single-aliquot OSL protocol using bracketing regenerative doses to accurately determine equivalent doses in quartz

International Nuclear Information System (INIS)

Folz, Elise; Mercier, Norbert

1999-01-01

In most cases, sediments show inherent heterogeneity in their luminescence behaviours and bleaching histories, and identical aliquots are not available: single-aliquot determination of the equivalent dose (ED) is then the approach of choice and the advantages of using regenerative protocols are outlined. Experiments on five laboratory bleached and dosed quartz samples, following the protocol described by Murray and Roberts (1998. Measurement of the equivalent dose in quartz using a regenerative-dose single aliquot protocol. Radiation Measurements 27, 171-184), showed the hazards of using a single regeneration dose: a 10% variation in the regenerative dose yielded some equivalent dose estimates that differed from the expected value by more than 5%. A protocol is proposed that allows the use of different regenerative doses to bracket the estimated equivalent dose. The measured ED is found to be in excellent agreement with the known value when the main regeneration dose is within 10% of the true equivalent dose

Characterizing Surplus US Plutonium for Disposition - 13199

Energy Technology Data Exchange (ETDEWEB)

Allender, Jeffrey S. [Savannah River National Laboratory, Aiken SC 29808 (United States); Moore, Edwin N. [Moore Nuclear Energy, LLC, Savannah River Site, Aiken SC 29808 (United States)

2013-07-01

The United States (US) has identified 61.5 metric tons (MT) of plutonium that is permanently excess to use in nuclear weapons programs, including 47.2 MT of weapons-grade plutonium. Surplus inventories will be stored safely by the Department of Energy (DOE) and then transferred to facilities that will prepare the plutonium for permanent disposition. The Savannah River National Laboratory (SRNL) operates a Feed Characterization program for the Office of Fissile Materials Disposition (OFMD) of the National Nuclear Security Administration (NNSA) and the DOE Office of Environmental Management (DOE-EM). SRNL manages a broad program of item tracking through process history, laboratory analysis, and non-destructive assay. A combination of analytical techniques allows SRNL to predict the isotopic and chemical properties that qualify materials for disposition through the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). The research also defines properties that are important for other disposition paths, including disposal to the Waste Isolation Pilot Plant (WIPP) as transuranic waste (TRUW) or to high-level waste (HLW) systems. (authors)

Plutonium-236 traces determination in plutonium-238 by α spectrometry

International Nuclear Information System (INIS)

Acena, M.L.; Pottier, R.; Berger, R.

1969-01-01

Two methods are described in this report for the determination of plutonium-236 traces in plutonium-238 by a spectrometry using semi-conductor detectors. The first method involves a direct comparison of the areas under the peaks of the α spectra of plutonium-236 and plutonium-238. The electrolytic preparation of the sources is carried out after preliminary purification of the plutonium. The second method makes it possible to determine the 236 Pu/ 238 Pu ratio by comparing the areas of the α peaks of uranium-232 and uranium-234, which are the decay products of the two plutonium isotopes respectively. The uranium in the source, also deposited by electrolysis, is separated from a 1 mg amount of plutonium either by a T.L.A. extraction, or by the use of ion-exchange resins. The report ends with a discussion of the results obtained with plutonium of two different origins. (authors) [fr

Plutonium controversy

International Nuclear Information System (INIS)

Gofman, J.W.

1976-01-01

If the world chooses to seek a solution to the energy dilemma through nuclear energy, the element plutonium will become an article of commerce to be handled in quantities of thousands of tonnes annually. Plutonium is a uniquely potent inhalation carcinogen, the potential induction of lung cancer dwarfing other possible toxic effects. For reasons to be presented here, it is the author's opinion that plutonium's carcinogenicity has been very seriously underestimated. If one couples the corrected carcinogenicity with the probable degree of industrial containment of the plutonium, it appears that the commercialization of a plutonium-based energy economy is not an acceptable option for society. Sagan's statement that ''the experience of 30 years supports the contention that plutonium can be used safely'' is manifestly indefensible. No meaningful epidemiological study of plutonium-exposed workers for that 30-year period has ever been done. Since thousands of those possibly exposed have left the industry and are not even available to follow-up, it is doubtful that any meaningful study of ''the experience of 30 years'' will ever be accomplished

Preparation of hexavalent plutonium and its determination in the presence of tetravalent plutonium; Preparation de plutonium hexavalent et dosage en presence de plutonium tetravalent

Energy Technology Data Exchange (ETDEWEB)

Corpel, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Corpel, J [Institut du Radium, 75 - Paris (France)

1958-07-01

In order to study the eventual reduction of plutonium from the VI-valent state to the IV-valent state, in sulphuric medium, under the influence of its own {alpha} radiation or of the {gamma}-rays from a cobalt-60 source, we have developed a method for preparing pure hexavalent plutonium and two methods for determining solutions containing tetravalent and hexavalent plutonium simultaneously. Hexavalent plutonium was prepared by anodic oxidation at a platinum electrode. Study of the oxidation yield as a function of various factors has made it possible to define experimental conditions giving complete oxidation. For concentrations in total plutonium greater than 1.5 x 10{sup -3} M, determination of the two valencies IV and VI was carried out by spectrophotometry at two wavelengths. For lower concentrations, the determination was done by counting, after separation of the tetravalent plutonium in the form of fluoride in the presence of a carrier. (author) [French] Afin d'etudier l'eventuelle reduction du plutonium de l'etat de valence VI a l'etat de valence IV, en milieu sulfurique sous l'influence de son propre rayonnement {alpha} ou des rayons {gamma} d'une source de cobalt-60, nous avons mis au point une methode de preparation de plutonium hexavalent pur et deux methodes de dosage des solutions contenant simultanement du plutonium tetravalent et du plutonium hexavalent. Nous avons prepare le plutonium hexavalent par oxydation anodique au contact d'une electrode de platine. L'etude de rendement de l'oxydation en fonction des divers facteurs nous a permis de definir des conditions experimentales donnant une oxydation complete. Pour des concentrations en plutonium total superieures a 1,5.10{sup -3} M, le dosage des deux valences IV et VI a ete realise par spectrophotometrie a deux longueurs d'onde. Pour des concentrations inferieures, le dosage a ete effectue par comptage apres separation du plutonium tetravalent sous la forme du fluorure en presence d'un entraineur

Plutonium in nature

International Nuclear Information System (INIS)

Madic, C.

1994-01-01

Plutonium in nature comes from natural sources and anthropogenic ones. Plutonium at the earth surface comes principally from anthropogenic sources. It is easily detectable in environment. The plutonium behaviour in environment is complex. It seems necessary for the future to reduce releases in environment, to improve predictive models of plutonium behaviour in geosphere, to precise biological impact of anthropogenic plutonium releases

Validation of an automated system for aliquoting of HIV-1 Env-pseudotyped virus stocks.

Science.gov (United States)

Schultz, Anke; Germann, Anja; Fuss, Martina; Sarzotti-Kelsoe, Marcella; Ozaki, Daniel A; Montefiori, David C; Zimmermann, Heiko; von Briesen, Hagen

2018-01-01

The standardized assessments of HIV-specific immune responses are of main interest in the preclinical and clinical stage of HIV-1 vaccine development. In this regard, HIV-1 Env-pseudotyped viruses play a central role for the evaluation of neutralizing antibody profiles and are produced according to Good Clinical Laboratory Practice- (GCLP-) compliant manual and automated procedures. To further improve and complete the automated production cycle an automated system for aliquoting HIV-1 pseudovirus stocks has been implemented. The automation platform consists of a modified Tecan-based system including a robot platform for handling racks containing 48 cryovials, a Decapper, a tubing pump and a safety device consisting of ultrasound sensors for online liquid level detection of each individual cryovial. With the aim to aliquot the HIV-1 pseudoviruses in an automated manner under GCLP-compliant conditions a validation plan was developed where the acceptance criteria-accuracy, precision as well as the specificity and robustness-were defined and summarized. By passing the validation experiments described in this article the automated system for aliquoting has been successfully validated. This allows the standardized and operator independent distribution of small-scale and bulk amounts of HIV-1 pseudovirus stocks with a precise and reproducible outcome to support upcoming clinical vaccine trials.

Field nondestructive assay measurements as applied to process inventories

International Nuclear Information System (INIS)

Westsik, G.A.

1979-08-01

An annual process equipment holdup inventory measurement program for a plutonium processing plant was instituted by Rockwell Hanford Operations (Rockwell) at Richland, Washington. The inventories, performed in 1977 and 1978, were designed to improve plutonium accountability and control. The inventory method used field nondestructive assay (NDA) measurement techniques with portable electronics and sodium iodide detectors. Access to and movement of plutonium in work areas was curtailed during the inventory process using administrative controls. Comparison of the two annual inventories showed good reproducibility of results within the calculated error ranges. For items where no plutonium movement occurred and which contained greater than 20 grams plutonium, the average measurement difference between the two inventories was 22%. The procedures and equipment used and the operational experience from the inventories are described

Deposition of plutonium in the lung of a worker following an accidental inhalation exposure

International Nuclear Information System (INIS)

Spitz, H.B.; Robinson, B.

The deposition of PuO 2 in the lungs of an occupationally exposed worker is characterized by assay for plutonium in excreta samples and from in vivo measurements of 241 Am in the thoracic region. Chelation therapy by intravenous injection of 1 gm Ca-DTPA was initially performed shortly after the incident and repeated using 0.5 gm of the chelate four additional times in subsequent days post intake. Analysis of the air sampler filter retrieved from the site of the exposure identified the isotopic composition and particle size of the plutonium material inhaled by the worker. Chelation with Ca-DTPA did not significantly reduce the magnitude of the lung or systemic deposition as determined from assay of plutonium in urine samples collected from the worker. In vivo measurements for 241 Am verify the retention of the inhaled material in the lung and also indicate the ingrowth of an amount of 241 Am as a daughter product of the 241 Pu initially inhaled

SEPARATION OF PLUTONIUM

Science.gov (United States)

Maddock, A.G.; Smith, F.

1959-08-25

A method is described for separating plutonium from uranium and fission products by treating a nitrate solution of fission products, uranium, and hexavalent plutonium with a relatively water-insoluble fluoride to adsorb fission products on the fluoride, treating the residual solution with a reducing agent for plutonium to reduce its valence to four and less, treating the reduced plutonium solution with a relatively insoluble fluoride to adsorb the plutonium on the fluoride, removing the solution, and subsequently treating the fluoride with its adsorbed plutonium with a concentrated aqueous solution of at least one of a group consisting of aluminum nitrate, ferric nitrate, and manganous nitrate to remove the plutonium from the fluoride.

Comparison of single-grain and small-aliquot OSL dose estimates in <3000 years old river sediments from South India

International Nuclear Information System (INIS)

Thomas, P.J.; Jain, M.; Juyal, N.; Singhvi, A.K.

2005-01-01

We report on OSL dose distributions derived from small-aliquot and single grains of quartz in young fluvial sediments sampled from the Penner River basin, South India. The single-grain dose distributions suggest that 13 out of 19 samples were well bleached. In many well-bleached samples, there was an underestimation in the single-aliquot dose estimates as compared to those from the single grain-the difference between average dose estimates determined by the two methods ranged from ∼1% to 31%. Such a dose underestimation was not detectable in poorly bleached samples. Various possible reasons for the discrepancy between single-grain and small-aliquot dose estimates are discussed. Although there is no satisfactory explanation for this discrepancy, we speculate that the difference in the stimulation wavelengths, 470+/-30nm in the case of single-aliquot and 532nm in the case of single grains, could perhaps be one of the reasons; this may occur because the stimulation wavelength affects the proportion of the medium and slow components in the initial signal

OSL sensitivity changes during single aliquot procedures: Computer simulations

DEFF Research Database (Denmark)

McKeever, S.W.S.; Agersnap Larsen, N.; Bøtter-Jensen, L.

1997-01-01

We present computer simulations of sensitivity changes obtained during single aliquot, regeneration procedures. The simulations indicate that the sensitivity changes are the combined result of shallow trap and deep trap effects. Four separate processes have been identified. Although procedures can...... be suggested to eliminate the shallow trap effects, it appears that the deep trap effects cannot be removed. The character of the sensitivity changes which result from these effects is seen to be dependent upon several external parameters, including the extent of bleaching of the OSL signal, the laboratory...

Forensic investigation of plutonium metal: a case study of CRM 126

International Nuclear Information System (INIS)

Byerly, B.L.; Floyd Stanley; Khal Spencer; Colletti, Lisa; Garduno, Katherine; Kuhn, Kevin; Lujan, Elmer; Martinez, Alex; Porterfield, Donivan; Jung Rim

2016-01-01

In this study, a certified plutonium metal reference material (CRM 126) with a known production history is examined using analytical methods that are commonly employed in nuclear forensics for provenancing and attribution. The measured plutonium isotopic composition and actinide assay are consistent with values reported on the reference material certificate. Model ages from U/Pu and Am/Pu chronometers agree with the documented production timeline. The results confirm the utility of these analytical methods and highlight the importance of a holistic approach for forensic study of unknown materials. (author)

Improved laboratory assays of Pu and U for SRP purification and finishing processes

International Nuclear Information System (INIS)

Holland, M.K.; Dorsett, R.S.

1986-01-01

Significant improvements have been made in routine assay techniques for uranium and plutonium as part of an effort to improve accountability at the Savannah River Plant (SRP). Emphasis was placed on input/output accountability points and key physical inventory tanks associated with purification and finishing processes. Improvements were made in existing assay methods; new methods were implemented; and the application of these methods was greatly expanded. Prior to assays, samples were validated via density measurements. Digital density meters precise to four, five, and six decimal places were used to meet specific requirements. Improved plutonium assay techniques are now in routine use: controlled-potential coulometry, ion-exchange coulometry, and Pu(III) diode-array spectrophotometry. A new state-of-the-art coulometer was fabricated and used to ensure maximum accuracy in verifying standards and in measuring plutonium in product streams. The diode-array spectrophotometer for Pu(III) measurements was modified with fiber optics to facilitate remote measurements; rapid, precise measurements made the technique ideally suited for high-throughput assays. For uranium assays, the isotope-dilution mass spectrometric (IDMS) method was converted to a gravimetric basis. The IDMS method and the existing Davies-Gray titration (gravimetric basis) have met accountability requirements for uranium. More recently, a Pu(VI) diode-array spectrophotometric method was used on a test basis to measure plutonium in shielded-cell input accountability samples. In addition, tests to measure uranium via diode-array spectrophotometry were initiated. This rapid, precise method will replace IDMS for certain key sample points

Plutonium content of human placental tissues after occupational exposure

International Nuclear Information System (INIS)

Russell, J.J.; Sikov, M.R.; Kathren, R.L.

2003-01-01

The placenta and umbilical cord were obtained following a normal live delivery from a volunteer donor who had received an accidental inhalation intake of plutonium 12 years prior to her pregnancy (Case 0777). Her employer estimated the intake to be about 73 Bq Class W plutonium. Based on bioassay results and clearance models in use at that time, they calculated her body content at the beginning of pregnancy to be about 5.6 Bq with an average concentration of approximately 60 mBq kg -1 . The placenta and cord from this pregnancy, along with the placenta and cord from a donor with no known exposure to plutonium (Case 0835), were divided and assayed for plutonium by ultrasensitive fission track analysis at two collaborating laboratories. Placental 239 Pu concentration values obtained by the two laboratories for Case 0777 agreed within a factor of 2 and were several-fold greater than for the control, Case 0835, as well as values that had been reported by others for unexposed populations. There was no elevated concentration of plutonium in the umbilical cord from the exposed person. The data yielded values of 0.16 and 0.27 for placental to maternal concentrations (C PI :C M ) that were of the same order of magnitude as the value of 0.1 the ICRP calculated for intakes before pregnancy. (author)

Plutonium content of human placental tissues after occupational exposure

Energy Technology Data Exchange (ETDEWEB)

Russell, J.J.; Sikov, M.R.; Kathren, R.L

2003-07-01

The placenta and umbilical cord were obtained following a normal live delivery from a volunteer donor who had received an accidental inhalation intake of plutonium 12 years prior to her pregnancy (Case 0777). Her employer estimated the intake to be about 73 Bq Class W plutonium. Based on bioassay results and clearance models in use at that time, they calculated her body content at the beginning of pregnancy to be about 5.6 Bq with an average concentration of approximately 60 mBq kg{sup -1}. The placenta and cord from this pregnancy, along with the placenta and cord from a donor with no known exposure to plutonium (Case 0835), were divided and assayed for plutonium by ultrasensitive fission track analysis at two collaborating laboratories. Placental {sup 239}Pu concentration values obtained by the two laboratories for Case 0777 agreed within a factor of 2 and were several-fold greater than for the control, Case 0835, as well as values that had been reported by others for unexposed populations. There was no elevated concentration of plutonium in the umbilical cord from the exposed person. The data yielded values of 0.16 and 0.27 for placental to maternal concentrations (C{sub PI}:C{sub M}) that were of the same order of magnitude as the value of 0.1 the ICRP calculated for intakes before pregnancy. (author)

Sorption/Desorption Interactions of Plutonium with Montmorillonite

Science.gov (United States)

Begg, J.; Zavarin, M.; Zhao, P.; Kersting, A. B.

2012-12-01

Plutonium (Pu) release to the environment through nuclear weapon development and the nuclear fuel cycle is an unfortunate legacy of the nuclear age. In part due to public health concerns over the risk of Pu contamination of drinking water, predicting the behavior of Pu in both surface and sub-surface water is a topic of continued interest. Typically it was assumed that Pu mobility in groundwater would be severely restricted, as laboratory adsorption studies commonly show that naturally occurring minerals can effectively remove plutonium from solution. However, evidence for the transport of Pu over significant distances at field sites highlights a relative lack of understanding of the fundamental processes controlling plutonium behavior in natural systems. At several field locations, enhanced mobility is due to Pu association with colloidal particles that serve to increase the transport of sorbed contaminants (Kersting et al., 1999; Santschi et al., 2002, Novikov et al., 2006). The ability for mineral colloids to transport Pu is in part controlled by its oxidation state and the rate of plutonium adsorption to, and desorption from, the mineral surface. Previously we have investigated the adsorption affinity of Pu for montmorillonite colloids, finding affinities to be similar over a wide range of Pu concentrations. In the present study we examine the stability of adsorbed Pu on the mineral surface. Pu(IV) at an initial concentration of 10-10 M was pre-equilibrated with montmorillonite in a background electrolyte at pH values of 4, 6 and 8. Following equilibration, aliquots of the suspensions were placed in a flow cell and Pu-free background electrolyte at the relevant pH was passed through the system. Flow rates were varied in order to investigate the kinetics of desorption and hence gain a mechanistic understanding of the desorption process. The flow cell experiments demonstrate that desorption of Pu from the montmorillonite surface cannot be modeled as a simple

The plutonium fuel cycles

International Nuclear Information System (INIS)

Pigford, T.H.; Ang, K.P.

1975-01-01

The quantities of plutonium and other fuel actinides have been calculated for equilibrium fuel cycles for 1000-MW water reactors fueled with slightly enriched uranium, water reactors fueled with plutonium and natural uranium, fast-breder reactors, gas-cooled reactors fueled with thorium and highly enriched uranium, and gas-cooled reactors fueled with thorium, plutonium and recycled uranium. The radioactivity quantities of plutonium, americium and curium processed yearly in these fuel cycles are greatest for the water reactors fueled with natural uranium and recycled plutonium. The total amount of actinides processed is calculated for the predicted future growth of the U.S. nuclear power industry. For the same total installed nuclear power capacity, the introduction of the plutonium breeder has little effect upon the total amount of plutonium in this century. The estimated amount of plutonium in the low-level process wastes in the plutonium fuel cycles is comparable to the amount of plutonium in the high-level fission product wastes. The amount of plutonium processed in the nuclear fuel cycles can be considerably reduced by using gas-cooled reactors to consume plutonium produced in uranium-fueled water reactors. These, and other reactors dedicated for plutonium utilization, could be co-located with facilities for fuel reprocessing ad fuel fabrication to eliminate the off-site transport of separated plutonium. (author)

Safeguardability of the vitrification option for disposal of plutonium

Energy Technology Data Exchange (ETDEWEB)

Pillay, K.K.S. [Los Alamos National Lab., NM (United States)

1996-05-01

Safeguardability of the vitrification option for plutonium disposition is rather complex and there is no experience base in either domestic or international safeguards for this approach. In the present treaty regime between the US and the states of the former Soviet Union, bilaterial verifications are considered more likely with potential for a third-party verification of safeguards. There are serious technological limitations to applying conventional bulk handling facility safeguards techniques to achieve independent verification of plutonium in borosilicate glass. If vitrification is the final disposition option chosen, maintaining continuity of knowledge of plutonium in glass matrices, especially those containing boron and those spike with high-level wastes or {sup 137}Cs, is beyond the capability of present-day safeguards technologies and nondestructive assay techniques. The alternative to quantitative measurement of fissile content is to maintain continuity of knowledge through a combination of containment and surveillance, which is not the international norm for bulk handling facilities.

Plutonium

International Nuclear Information System (INIS)

Anon.

1995-01-01

Plutonium, which was obtained and identified for the first time in 1941 by chemist Glenn Seaborg - through neutron irradiation of uranium 238 - is closely related to the history of nuclear energy. From the very beginning, because of the high radiotoxicity of plutonium, a tremendous amount of research work has been devoted to the study of the biological effects and the consequences on the environment. It can be said that plutonium is presently one of the elements, whose nuclear and physico-chemical characteristics are the best known. The first part of this issue is a survey of the knowledge acquired on the subject, which emphasizes the sanitary effects and transfer into the environment. Then the properties of plutonium related to energy generation are dealt with. Fissionable, like uranium 235, plutonium has proved a high-performance nuclear fuel. Originally used in breeder reactors, it is now being more and more widely recycled in light water reactors, in MOX fuel. Reprocessing, recycling and manufacturing of these new types of fuel, bound of become more and more widespread, are now part of a self-consistent series of operations, whose technical, economical, industrial and strategical aspects are reviewed. (author)

Learning more about plutonium

International Nuclear Information System (INIS)

2005-01-01

This document offers chemical, metallurgical and economical information on the plutonium, a hard white radioelement. It deals also on the plutonium formation in the earth, the plutonium use in the nuclear industry, the plutonium in the environment and the plutonium toxicity. (A.L.B.)

Rapid and automated determination of plutonium and neptunium in environmental samples

International Nuclear Information System (INIS)

Qiao, J.

2011-03-01

This thesis presents improved analytical methods for rapid and automated determination of plutonium and neptunium in environmental samples using sequential injection (SI) based chromatography and inductively coupled plasma mass spectrometry (ICP-MS). The progress of methodology development in this work consists of 5 subjects stated as follows: 1) Development and optimization of an SI-anion exchange chromatographic method for rapid determination of plutonium in environmental samples in combination of inductively coupled plasma mass spectrometry detection (Paper II); (2) Methodology development and optimization for rapid determination of plutonium in environmental samples using SI-extraction chromatography prior to inductively coupled plasma mass spectrometry (Paper III); (3) Development of an SI-chromatographic method for simultaneous determination of plutonium and neptunium in environmental samples (Paper IV); (4) Investigation of the suitability and applicability of 242 Pu as a tracer for rapid neptunium determination using anion exchange chromatography in an SI-network coupled with inductively coupled plasma mass spectrometry (Paper V); (5) Exploration of macro-porous anion exchange chromatography for rapid and simultaneous determination of plutonium and neptunium within an SI system (Paper VI). The results demonstrate that the developed methods in this study are reliable and efficient for accurate assays of trace levels of plutonium and neptunium as demanded in different situations including environmental risk monitoring and assessment, emergency preparedness and surveillance of contaminated areas. (Author)

Rapid and automated determination of plutonium and neptunium in environmental samples

Energy Technology Data Exchange (ETDEWEB)

Qiao, J.

2011-03-15

This thesis presents improved analytical methods for rapid and automated determination of plutonium and neptunium in environmental samples using sequential injection (SI) based chromatography and inductively coupled plasma mass spectrometry (ICP-MS). The progress of methodology development in this work consists of 5 subjects stated as follows: 1) Development and optimization of an SI-anion exchange chromatographic method for rapid determination of plutonium in environmental samples in combination of inductively coupled plasma mass spectrometry detection (Paper II); (2) Methodology development and optimization for rapid determination of plutonium in environmental samples using SI-extraction chromatography prior to inductively coupled plasma mass spectrometry (Paper III); (3) Development of an SI-chromatographic method for simultaneous determination of plutonium and neptunium in environmental samples (Paper IV); (4) Investigation of the suitability and applicability of 242Pu as a tracer for rapid neptunium determination using anion exchange chromatography in an SI-network coupled with inductively coupled plasma mass spectrometry (Paper V); (5) Exploration of macro-porous anion exchange chromatography for rapid and simultaneous determination of plutonium and neptunium within an SI system (Paper VI). The results demonstrate that the developed methods in this study are reliable and efficient for accurate assays of trace levels of plutonium and neptunium as demanded in different situations including environmental risk monitoring and assessment, emergency preparedness and surveillance of contaminated areas. (Author)

Developing a single-aliquot protocol for measuring equivalent dose in biogenic carbonates

International Nuclear Information System (INIS)

Stirling, R.J.; Duller, G.A.T.; Roberts, H.M.

2012-01-01

Exploiting biogenic carbonates as thermoluminescence dosimeters requires an understanding of trap kinetics and an appropriate sequence with which to measure equivalent dose. The trap kinetics of two high temperature peaks (peaks II and III) from calcitic snail opercula have been investigated resulting in the calculation of lifetimes of 7.4 × 10 7 and 1.4 × 10 11 years for the two peaks respectively. Two measurement sequences, based upon changes in the application and measurement of a test dose, have been applied to peaks II and III, and though both methods were equally successful in dose recovery and production of a dose response curve some differences were observed. Primarily, the use of method 1 lead to dose dependant sensitivity change implying competition effects occurring during irradiation; method 2 did not experience this phenomenon. As a consequence method 2 was chosen as the most appropriate protocol for single-aliquot dating of this material. When assessing the TL behaviour of the two peaks, peak II performed poorly in dose recovery experiments recovering a dose 60–100% larger than that applied. Disproportionate growth of peak II in response to a beta dose applied prior to measurement, compared to growth following regeneration doses indicated that peak II was not suitable for use in single-aliquot protocols. However, dose recovery results for peak III were all within errors of unity of the given dose, and peak III was therefore chosen as the most appropriate peak for TL dosimetry in these single-aliquot procedures. The lifetime of charge in peak III is sufficient to date over many millions of years, and furthermore using the chosen method 2 the dose response curve has a D 0 of 3,250 ± 163 Gy allowing dating to over 3 million years.

Time effect and aliquot concentration in Streptococcus mutans elimination by plasma needle

Science.gov (United States)

García-Alcantara, E.; López-Callejas, R.; Peña-Eguiluz, R.; Lagunas-Bernabé, S.; Valencia-Alvarado, R.; Mercado-Cabrera, A.; Barocio, S. R.; Muñoz-Castro, A. E.; Rodríguez-Méndez, B. G.; de la Piedad-Beneitez, A.

2012-06-01

Atmospheric plasma needle systems are being intensively studied with a view to potential applications in medicine. The aim of this in vitro study is the improved elimination of Streptococcus Mutants (S. mutans) bacteria. A 5 ml volume of Luria-Bertani culture medium has been inoculated with a test bacterial population and incubated during 24 hours, followed by ten dilutions producing aliquots at 20, 50 and 100 micro l per dilution. Each aliquot is deposited on a paper filter and then exposed to a 2 W RF room pressure helium plasma needle discharge at a 1.5 l.p.m. rate for 1, 3, 5 or 7 minutes. Each sample paper is placed in a test tube, again containing Luria-Bertani fluid, in order to develop a new bacterium colony after a 24h incubation period. The plasma needle lethality has been evaluated from absorbance studies by means of a 6305 Jeway spectrophotometer at a 600 nm wavelength, indicating a clear correlation with exposure time. These studies validate the high disinfection efficacy of the plasma needle.

Time effect and aliquot concentration in Streptococcus mutans elimination by plasma needle

International Nuclear Information System (INIS)

García-Alcantara, E; López-Callejas, R; De la Piedad-Beneitez, A; Peña-Eguiluz, R; Valencia-Alvarado, R; Mercado-Cabrera, A; Barocio, S R; Muñoz-Castro, A E; Rodríguez-Méndez, B G; Lagunas-Bernabé, S

2012-01-01

Atmospheric plasma needle systems are being intensively studied with a view to potential applications in medicine. The aim of this in vitro study is the improved elimination of Streptococcus Mutants (S. mutans) bacteria. A 5 ml volume of Luria-Bertani culture medium has been inoculated with a test bacterial population and incubated during 24 hours, followed by ten dilutions producing aliquots at 20, 50 and 100 micro l per dilution. Each aliquot is deposited on a paper filter and then exposed to a 2 W RF room pressure helium plasma needle discharge at a 1.5 l.p.m. rate for 1, 3, 5 or 7 minutes. Each sample paper is placed in a test tube, again containing Luria-Bertani fluid, in order to develop a new bacterium colony after a 24h incubation period. The plasma needle lethality has been evaluated from absorbance studies by means of a 6305 Jeway spectrophotometer at a 600 nm wavelength, indicating a clear correlation with exposure time. These studies validate the high disinfection efficacy of the plasma needle.

Civil plutonium management

International Nuclear Information System (INIS)

Sicard, B.; Zaetta, A.

2004-01-01

During 1960 and 1970 the researches on the plutonium recycling in fast neutrons reactors were stimulated by the fear of uranium reserves diminishing. At the beginning of 1980, the plutonium mono-recycling for water cooled reactors is implementing. After 1990 the public opinion concerning the radioactive wastes management and the consequences of the disarmament agreements between Russia and United States, modified the context. This paper presents the today situation and technology associated to the different options and strategical solutions of the plutonium management: the plutonium use in the world, the neutronic characteristics, the plutonium effect on the reactors characteristics, the MOX behavior in the reactors, the MOX fabrication and treatment, the possible improvements to the plutonium use, the concepts performance in a nuclear park. (A.L.B.)

Test and evaluation of the in-line plutonium solution K-absorption-edge densitometer at the Savannah River Plant. Phase I. Off-line testing results

International Nuclear Information System (INIS)

Smith, H.A. Jr.; Marks, T.; Johnson, S.S.

1982-04-01

An in-line, plutonium-solution, K-edge absorption densitometer has been developed at Los Alamos and is currently undergoing test and evaluation at the Savannah River Plant (SRP). The first phase of the test and evaluation (off-line instrument calibration and solution assays) was completed, and preparations are under way to install the instrument in-line, as soon as process schedules permit. Calibration data in the design concentration range of 25 to 40 g Pu/L demonstrate routine achievement of densitometry assay precisions of 0.5% or better in 40 min. Plutonium assays at concentrations outside the calibration range were investigated in an effort to define better the limitations of the instrument and address other possible assay situations at SRP. Densitometry precisions obtained for 40-min assays range from 3% to 5 g Pu/L down to 0.4% at 70 g Pu/L. At higher plutonium concentrations, the precision deteriorated due to increasing gamma-ray absorption by the solution. In addition, with actinide concentrations above approximately 100 g/L, the assay accuracy also suffered because of enhanced small-angle scattering effects in the large sample cell. Measurements on mixed U/Pu solutions demonstrated the feasibility of accurate plutonium assays with correction for the large uranium matrix contributions being determined from the measurement data. The 239 240 Pu weight fractions and 241 Pu/ 239 Pu and 238 Pu/ 239 Pu isotopic ratios can be determined. In a mockup of the in-line solution plumbing system, all assay sequences, error conditions, and interlock criteria were exercised and verified to be working properly

Importance of 241 Am Determination in the Characterization of PuO2 Standards for Calorimetric Assay.

Energy Technology Data Exchange (ETDEWEB)

Sampson, Thomas E.

2005-01-01

Plutonium dioxide (PuO{sub 2}) standards are often used both as heat standards and isotopic standards for calorimetric assay. Calorimetric assay is the combination of the power in watts measured in a calorimeter with the effective specific power (P{sub eff}) in watts/g Pu, determined either by nondestructive gamma-ray assay or by destructive mass spectrometry, to yield the total elemental plutonium mass in the sample. To use a PuO{sub 2} sample as a heat standard for calorimetry, one must determine both the plutonium mass and P{sub eff} with very small uncertainties and then calculate the sample watts from the known plutonium mass, specific powers, and isotopic composition. Well-characterized PuO{sub 2} standards have plutonium mass values determined by analytical chemistry with a precision and accuracy on the order of 0.1%-0.2% relative to the total mass of the sample. Mass spectrometry, typically used to determine the isotopic fractions of plutonium standards, is very accurate and precise for the major isotopes but is somewhat less precise for low-abundance isotopes. The characterization of the {sup 241}Am/Pu ratio in the standard is also of great importance because {sup 241}Am can contribute significantly to P{sub eff} and to the heat output of the standard. The determination of the {sup 241}Am/Pu ratio in a plutonium-bearing sample is a process that is less standardized than mass spectrometry. There are no certified reference materials (CRMs) traceable to the national measurement system for {sup 241}Am in plutonium, and routine analytical {sup 241}Am/Pu ratio measurements often exhibit uncertainties of several percent relative to the total plutonium or greater.

Holdup measurements of plutonium in glove box exhausts

International Nuclear Information System (INIS)

Glick, J.B.; Haas, F.X.; McKamy, J.N.; Garrett, A.G.

1991-01-01

A new measurement technique has been developed to quantify plutonium in process glove box exhausts. The technique implemented at Rocky Flats Plant utiltizes a shielded, collimated 0.5in. x 0.5in. bismuth germanate (BGO) gamma-ray detector. Pairs of measurements are made at one foot intervals along the duct. One measurement is made with the detector viewing the bottom of the duct with the detector crystal approximately 2 inches from the duct surface. The second measurement is made on the top of the exhaust pipe with the detector crystal 2 inches from the top of the duct. When the detector is placed in the bottom assay position, the area of the holdup material is assumed to extend beyond the detector field of view. The concentration of plutonium in g/cm 2 is obtained from this bottom measurement. The deposit width is determined from a model developed to relate the deposit width to the ratio of the count rates measured at the two positions, above and below the duct. Once a deposit width has been calculated, it is multiplied by the concentration determined from the bottom measurement to yield a mass- per-unit-length at the duct location. Total plutonium mass is then determined by multiplying the duct length by the average of the mass- per-unit length assays performed along the duct. The applicability of the technique is presented in a comparison of field measurement data to analysis results on material removed from the ducts. 3 refs., 3 figs., 1 tab

Using the OSL single-aliquot regenerative-dose protocol with quartz extracted from building materials in retrospective dosimetry

DEFF Research Database (Denmark)

Bøtter-Jensen, L.; Solongo, S.; Murray, A.S.

2000-01-01

We report on the application of the single-aliquot regenerative-dose (SAR) protocol to the optically stimulated luminescence signal from quartz extracted from fired bricks acid unfired mortar in retrospective dosimetry. The samples came from a radioactive materials storage facility, with ambient...... dose rates of about 0.1 mGy/h. A detailed dose-depth profile was analysed from one brick, and compared with dose records from area TL dosemeters. Small-aliquot dose-distributions were analysed from the mortar samples; one associated with the exposed brick, and one from a remote site exposed only...

The plutonium society

International Nuclear Information System (INIS)

Mez, L.; Richter, M.

1981-01-01

The lectures of an institute are reported on, which took place between 25th and 27th January 1980 in Berlin. The subsequent public panel discussion with representations from the political parties is then documentated in a few press-reports. The themes of the 8 lectures are: views and facts on plutonium, plutonium as an energy resource, military aspects of the production of plutonium, economic aspects of the plutonium economy, the position of the trade unions on the industrial reconversion, the alleged inevitability of a plutonium society and the socio-political alternatives and perspectives of nuclear waste disposal. (UA) [de

What is plutonium stabilization, and what is safe storage of plutonium?

International Nuclear Information System (INIS)

Forsberg, C.W.

1995-01-01

The end of the cold war has resulted in the shutdown of nuclear weapons production and the start of dismantlement of significant numbers of nuclear weapons. This, in turn, is creating an inventory of plutonium requiring interim and long-term storage. A key question is, ''What is required for safe, multidecade, plutonium storage?'' The requirements for storage, in turn, define what is needed to stabilize the plutonium from its current condition into a form acceptable for interim and long-term storage. Storage requirements determine if research is required to (1) define required technical conditions for interim and long-term storage and (2) develop or improve current stabilization technologies. Storage requirements depend upon technical, policy, and economic factors. The technical issues are complicated by several factors. Plutonium in aerosol form is highly hazardous. Plutonium in water is hazardous. The plutonium inventory is in multiple chemical forms--some of which are chemically reactive. Also, some of the existing storage forms are clearly unsuitable for storage periods over a few years. Gas generation by plutonium compounds complicates storage: (1) all plutonium slowly decays creating gaseous helium and (2) the radiation from plutonium decay can initiate many chemical reactions-some of which generate significant quantities of gases. Gas generation can pressurize sealed storage packages. Last nuclear criticality must be avoided

Plutonium solubilities

International Nuclear Information System (INIS)

Puigdomnech, I.; Bruno, J.

1991-02-01

Thermochemical data has been selected for plutonium oxide, hydroxide, carbonate and phosphate equilibria. Equilibrium constants have been evaluated in the temperature range 0 to 300 degrees C at a pressure of 1 bar to T≤100 degrees C and at the steam saturated pressure at higher temperatures. Measured solubilities of plutonium that are reported in the literature for laboratory experiments have been collected. Solubility data on oxides, hydroxides, carbonates and phosphates have been selected. No solubility data were found at temperatures higher than 60 degrees C. The literature solubility data have been compared with plutonium solubilities calculated with the EQ3/6 geochemical modelling programs, using the selected thermodynamic data for plutonium. (authors)

Plutonium in uranium deposits

International Nuclear Information System (INIS)

Curtis, D.; Fabryka-Martin, J.; Aguilar, R.; Attrep, M. Jr.; Roensch, F.

1992-01-01

Plutonium-239 (t 1/2 , 24,100 yr) is one of the most persistent radioactive constituents of high-level wastes from nuclear fission power reactors. Effective containment of such a long-lived constituent will rely heavily upon its containment by the geologic environment of a repository. Uranium ore deposits offer a means to evaluate the geochemical properties of plutonium under natural conditions. In this paper, analyses of natural plutonium in several ores are compared to calculated plutonium production rates in order to evaluate the degree of retention of plutonium by the ore. The authors find that current methods for estimating production rates are neither sufficiently accurate nor precise to provide unambiguous measures of plutonium retention. However, alternative methods for evaluating plutonium mobility are being investigated, including its measurement in natural ground waters. Preliminary results are reported and establish the foundation for a comprehensive characterization of plutonium geochemistry in other natural environments

Conversion of metal plutonium to plutonium dioxide by pyrochemical method

Energy Technology Data Exchange (ETDEWEB)

Panov, A.V.; Subbotin, V.G. [Russian Federal Nuclear Center, ALL-Russian Science and Research Institute of Technical Physics, Snezhinsk (Russian Federation); Mashirev, V.P. [ALL-Russian Science and Research Institute of Chemical Technology, Moscow (Russian Federation)

2000-07-01

Report contains experimental results on metal plutonium of weapon origin samples conversion to plutonium dioxide by pyrochemical method. Circuits of processes are described. Their advantages and shortcomings are shown. Parameters of plutonium dioxide powders (phase and fraction compositions, poured density) manufactured by pyrochemical method in RFNC-VNIITF are shown as well. (authors)

The use of plutonium

International Nuclear Information System (INIS)

Marshall, W.

1980-01-01

The use of plutonium as a vital energy source producing maximum economic benefit with minimum proliferation risks is discussed. Having considered the production of plutonium, several possible plutonium fuel cycle options are identified and the economic value to be attached to plutonium for each examined. It is shown how the use of plutonium in fast reactors gives an opportunity for a non-proliferation policy not available when plutonium is used only in thermal reactors. From the technical considerations reviewed concerning plutonium and fast reactors it is shown that an economic regime involving international trade in spent thermal reactor fuel is possible which benefits equally those countries with fast reactors and those without and also assists in avoiding the proliferation of nuclear weapons. (U.K.)

Properties of plutonium

International Nuclear Information System (INIS)

Ahn, Jin Su; Yoon, Hwan Ki; Min, Kyung Sik; Kim, Hyun Tae; Ahn, Jong Sung; Kwag, Eon Ho; Ryu, Keon Joong

1996-03-01

Plutonium has unique chemical and physical properties. Its uniqueness in use has led to rare publications, in Korea. This report covers physical aspects of phase change of metal plutonium, mechanical properties, thermal conductivity, etc, chemical aspects of corrosion, oxidation, how to produce plutonium from spent fuels by describing various chemical treatment methods, which are currently used and were used in the past. It also contains characteristics of the purex reprocessing process which is the most widely used nowadays. And show processes to purify and metalize from recovered plutonium solution. Detection and analysis methods are introduced with key pints for handling, critical safety, toxicity, and effects on peoples. This report gives not only a general idea on what plutonium is, rather than deep technical description, but also basic knowledge on plutonium production and safeguards diversion from the view point of nonproliferation. 18 refs. (Author) .new

Properties of plutonium

Energy Technology Data Exchange (ETDEWEB)

Ahn, Jin Su; Yoon, Hwan Ki; Min, Kyung Sik; Kim, Hyun Tae; Ahn, Jong Sung; Kwag, Eon Ho; Ryu, Keon Joong [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of)

1996-03-01

Plutonium has unique chemical and physical properties. Its uniqueness in use has led to rare publications, in Korea. This report covers physical aspects of phase change of metal plutonium, mechanical properties, thermal conductivity, etc, chemical aspects of corrosion, oxidation, how to produce plutonium from spent fuels by describing various chemical treatment methods, which are currently used and were used in the past. It also contains characteristics of the purex reprocessing process which is the most widely used nowadays. And show processes to purify and metalize from recovered plutonium solution. Detection and analysis methods are introduced with key pints for handling, critical safety, toxicity, and effects on peoples. This report gives not only a general idea on what plutonium is, rather than deep technical description, but also basic knowledge on plutonium production and safeguards diversion from the view point of nonproliferation. 18 refs. (Author) .new.

Plutonium-238 and plutonium-239 metabolism in dairy cows following ingestion of mixed oxides

International Nuclear Information System (INIS)

Patzer, R.G.; Mullen, A.A.; Sutton, W.W.; Potter, G.D.; Mosley, R.E.; Efurd, D.W.; Stalnaker, N.D.

1985-01-01

Dairy cows were given oral dosage of plutonium-238 and plutonium-239 dioxide particles in a study to determine the relative gastrointestinal absorption and tissue distribution of the nuclides. Two cows were given particles in which the two isotopes were homogeneously mixed within the particles. A third cow was given two batches of particles which contained either plutonium-238 or plutonium-239. Results indicate that, when the two isotopes of plutonium are homogeneous within the particles, there is no difference between plutonium-238 and plutonium-239 in the relative gastrointestinal absorption and tissue distribution

High-temperature enthalpies of plutonium monocarbide and plutonium sesquicarbide

International Nuclear Information System (INIS)

Oetting, F.L.

1979-01-01

The high-temperature enthalpies of plutonium monocarbide and plutonium sesquicarbide have been determined with a copper-block calorimeter of the isoperibol type. The experimental enthalpy data, which was measured relative to 298 K, covered the temperature range from 400 to 1500 K. The calculation of the temperature rise of the calorimeter takes into account the added heat evolution from the radioactive decay of the plutonium samples. These enthalpy results, combined with the heat capacity and entropy of the respective carbide at 298 K available from the literature, has made it possible to generate tables of thermodynamic functions for the plutonium carbides. The behavior of the heat capacity of both of the plutonium carbides, i.e., a relatively steep increase in the heat capacity as the temperature increases, may be attributed to a premelting effect with the formation of vacancies within the crystal lattice although a theoretical treatment of this phenomenon is not given

ARIES nondestructive assay system operation and performance

International Nuclear Information System (INIS)

Cremers, Teresa L.; Hansen, Walter J.; Herrera, Gary D.; Nelson, David C.; Sampson, Thomas E.; Scheer, Nancy L.

2000-01-01

The ARIES (Advanced Recovery and Integrated Extraction System) Project is an integrated system at the Los Alamos Plutonium Facility for the dismantlement of nuclear weapons. The plutonium produced by the ARIES process was measured by an integrated nondestructive assay (NDA) system. The performance of the NDA systems was monitored by a measurement control program which is a part of a nuclear material control and accountability system. In this paper we will report the results of the measurements of the measurement control standards as well as an overview of the measurement of the ARIES process materials

Evaluation of an automated assay system to measure soil radionuclides by L x-ray and gamma-ray spectrometry

International Nuclear Information System (INIS)

Nyhan, J.W.; Drennon, B.J.; Crowell, J.M.

1982-08-01

An automated radionuclide assay system for conducting soil radioassays using L x-ray and gamma-ray spectrometry was evaluated. Wet chemistry assay procedures were shown to be considerably more time consuming than similar analyses of soil on this radionuclide assay system. The detection limits of 241 Am and plutonium were determined, as well as the reproducibility of radionuclide assay results. The L x-ray spectrometric measurements were compared with radiochemical analyses on several tuff samples. The assay system's intrinsic germanium detector was found to respond linearly to varying low concentrations of 241 Am and plutonium, both of which were easily detected in the presence of elevated concentrations of 137 Cs

Plutonium

International Nuclear Information System (INIS)

Koelzer, W.

1989-03-01

This report contains with regard to 'plutonium' statements on chemistry, occurrence and reactions in the environment, handling procedures in the nuclear fuel cycle, radiation protection methods, biokinetics, toxicology and medical treatment to make available reliable data for the public discussion on plutonium especially its use in nuclear power plants and its radiological assessment. (orig.) [de

Plutonium

International Nuclear Information System (INIS)

Mueller-Christiansen, K.; Wollesen, M.

1979-01-01

As emotions and fear of plutonium are neither useful for the non-professionals nor for the political decision makers and the advantages and disadvantages of plutonium can only put against each other under difficulties, the paper wants to present the most essential scientific data of plutonium in a generally understandable way. Each of the individual sections is concluded and they try to give an answer to the most discussed questions. In order to make understanding easier, the scientific facts are only brought at points where it cannot be done without for the correctness of the presentation. Many details were left out knowingly. On the other hand, important details are dealt with several times if it seems necessary for making the presentation correct. The graphical presentations and the figures in many cases contain more than said in the text. They give the interested reader hints to scientific-technical coherences. The total material is to enable the reader to form his own opinion on plutonium problems which are being discussed in public. (orig./HP) [de

A 252Cf based nondestructive assay system for fissile material

International Nuclear Information System (INIS)

Menlove, H.O.; Crane, T.W.

1978-01-01

A modulated 252 Cf source assay system 'Shuffler' based on fast-or-thermal-neutron interrogation combined with delayed-neutron counting has been developed for the assay of fissile material. The 252 Cf neutron source is repetitively transferred from the interrogation position to a shielded position while the delayed neutrons are counted in a high efficiency 3 He neutron well-counter. For samples containing plutonium, this well-counter is also used in the passive coincidence mode to assay the effective 240 Pu content. The design of an optimized neutron tailoring assembly for fast-neutron interrogation using a Monte Carlo Neutron Computer Code is described. The Shuffler system has been applied to the assay of fuel pellets, inventory samples, irradiated fuel and plutonium mixed-oxide fuel. The system can assay samples with fissile contents from a few milligrams up to several kilograms using thermal-neutron interrogation for the low mass samples and fast-neutron interrogation for the high mass samples. Samples containing 235 U- 238 U, or 233 U-Th, or UO 2 -PuO 2 fuel mixtures have been assayed with the Shuffler system. (Auth.)

PRODUCTION OF PLUTONIUM METAL

Science.gov (United States)

Lyon, W.L.; Moore, R.H.

1961-01-17

A process is given for producing plutonium metal by the reduction of plutonium chloride, dissolved in alkali metal chloride plus or minus aluminum chloride, with magnesium or a magnesium-aluminum alloy at between 700 and 800 deg C and separating the plutonium or plutonium-aluminum alloy formed from the salt.

Plutonium storage phenomenology

International Nuclear Information System (INIS)

Szempruch, R.

1995-12-01

Plutonium has been produced, handled, and stored at Department of Energy (DOE) facilities since the 1940s. Many changes have occurred during the last 40 years in the sources, production demands, and end uses of plutonium. These have resulted in corresponding changes in the isotopic composition as well as the chemical and physical forms of the processed and stored plutonium. Thousands of ordinary food pack tin cans have been used successfully for many years to handle and store plutonium. Other containers have been used with equal success. This paper addressees the exceptions to this satisfactory experience. To aid in understanding the challenges of handling plutonium for storage or immobilization the lessons learned from past storage experience and the necessary countermeasures to improve storage performance are discussed

Results of the international Pu-2000 exercise for plutonium isotopic composition measurements

International Nuclear Information System (INIS)

Morel, J.; Bickel, M.; Hill, C.; Verbruggen, A.

2004-01-01

An international comparison for plutonium isotopic composition measurement, known as the Pu-2000 exercise, was organized by the ESARDA NDA-WG (European Safeguards Research and Development Association, Working Group on Techniques and Standards for Non-Destructive Assay). The aim of this comparison was to test X- and γ-ray spectrometry methods over a large range of isotopic ratios. These methods are based on the complex analysis of several X- and γ-rays in the KX region of the plutonium spectrum and also in the 120-700 keV energy range. The results obtained by the participants with their corresponding uncertainties are presented in this document and compared to the declared values. The main conclusions of the work are also given. No important bias due to an inadequate knowledge of the nuclear data for plutonium isotopes was observed

Use of a Gantry robot in the assay of radioactive materials

International Nuclear Information System (INIS)

Phelan, P.F.; Beugelsdijk, T.J.; Powell, W.D.; Schneider, D.N.; Staley, H.C.; Blankenship, R.

1989-01-01

A large industrial robot has been installed in our plutonium processing facility to speed the assay of materials in process. The robot routinely transports radioactive items weighing 20 lbs or more between an automated inventory system and the analytical instruments. Because the system operates unattended under computer control, assays are now performed around-the-clock instead of just 8 hrs per day, thereby greatly increasing the utilization of our instruments. (When the system becomes fully operational, we except a four-fold increase in productivity.) In addition, recordkeeping has improved, the plutonium is better protected from theft, and our personnel are exposed to less radiation than before. 4 figs

Plutonium controversy

International Nuclear Information System (INIS)

Richmond, C.R.

1980-01-01

The toxicity of plutonium is discussed, particularly in relation to controversies surrounding the setting of radiation protection standards. The sources, amounts of, and exposure pathways of plutonium are given and the public risk estimated

Perspective on plutonium

International Nuclear Information System (INIS)

Sun, L.S.

1993-01-01

This paper is intended as a brief overview on the element plutonium. Plutonium is the first primarily man-made element to play a significant role not only in technological development, but also in the economic growth of many countries. The importance of plutonium centers around its enormous energy making it ideal for wide-scale use in reactors, while the nuclear industry continues to work toward improving safety and efficiency of plutonium as a reactor fuel politicians and the public still debate over the safety and benefits of nuclear power. (30 refs.)

Repeat testing of low-level HIV-1 RNA: assay performance and implementation in clinical trials.

Science.gov (United States)

White, Kirsten; Garner, Will; Wei, Lilian; Eron, Joseph J; Zhong, Lijie; Miller, Michael D; Martin, Hal; Plummer, Andrew; Tran-Muchowski, Cecilia; Lindstrom, Kim; Porter, James; Piontkowsky, David; Light, Angela; Reiske, Heinz; Quirk, Erin

2018-05-15

Assess the performance of HIV-1 RNA repeat testing of stored samples in cases of low-level viremia during clinical trials. Prospective and retrospective analysis of randomized clinical trial samples and reference standards. To evaluate assay variability of the Cobas AmpliPrep/Cobas TaqMan HIV-1 Test, v2.0, three separate sources of samples were utilized: the World Health Organization (WHO) HIV reference standard (assayed using 50 independent measurements at six viral loads <200 copies/ml), retrospective analysis of four to six aliquots of plasma samples from four clinical trial participants, and prospective repeat testing of 120 samples from participants in randomized trials with low-level viremia. The TaqMan assay on the WHO HIV-1 RNA standards at viral loads <200 copies/ml performed within the expected variability according to assay specifications. However, standards with low viral loads of 36 and 18 copies/ml reported values of ≥ 50 copies/ml in 66 and 18% of tests, respectively. In participants treated with antiretrovirals who had unexpected viremia of 50-200 copies/ml after achieving <50 copies/ml, retesting of multiple aliquots of stored plasma found <50 copies/ml in nearly all cases upon retesting (14/15; 93%). Repeat testing was prospectively implemented in four clinical trials for all samples with virologic rebound of 50-200 copies/ml (n = 120 samples from 92 participants) from which 42% (50/120) had a retest result of less than 50 copies/ml and 58% (70/120) retested ≥ 50 copies/ml. The TaqMan HIV-1 RNA assay shows variability around 50 copies/ml that affects clinical trial results and may impact clinical practice. In participants with a history of viral load suppression, unexpected low-level viremia may be because of assay variability rather than low drug adherence or true virologic failure. Retesting a stored aliquot of the same sample may differentiate between assay variability and virologic failure as the source of viremia

Plutonium controversy

Energy Technology Data Exchange (ETDEWEB)

Richmond, C.R.

1980-01-01

The toxicity of plutonium is discussed, particularly in relation to controversies surrounding the setting of radiation protection standards. The sources, amounts of, and exposure pathways of plutonium are given and the public risk estimated. (ACR)

Recent developments in the dissolution and automated analysis of plutonium and uranium for safeguards measurements

International Nuclear Information System (INIS)

Jackson, D.D.; Marsh, S.F.; Rein, J.E.; Waterbury, G.R.

1975-01-01

The status of a program to develop assay methods for plutonium and uranium for safeguards purposes is presented. The current effort is directed more toward analyses of scrap-type material with an end goal of precise automated methods that also will be applicable to product materials. A guiding philosophy for the analysis of scrap-type materials, characterized by heterogeneity and difficult dissolution, is relatively fast dissolution treatment to effect 90 percent or more solubilization of the uranium and plutonium, analysis of the soluble fraction by precise automated methods, and gamma-counting assay of any residue fraction using simple techniques. A Teflon-container metal-shell apparatus provides acid dissolutions of typical fuel cycle materials at temperatures to 275 0 C and pressures to 340 atm. Gas--solid reactions at elevated temperatures separate uranium from refractory materials by the formation of volatile uranium compounds. The condensed compounds then are dissolved in acid for subsequent analysis. An automated spectrophotometer is used for the determination of uranium and plutonium. The measurement range is 1 to 14 mg of either element with a relative standard deviation of 0.5 percent over most of the range. The throughput rate is 5 min per sample. A second-generation automated instrument is being developed for the determination of plutonium. A precise and specific electroanalytical method is used as its operational basis. (auth)

Plutonium, nuclear fuel; Le plutonium, combustible nucleaire

Energy Technology Data Exchange (ETDEWEB)

Grison, E [Commissariat a l' Energie Atomique, Fontenay aux Roses (France). Centre d' Etudes Nucleaires, Saclay

1960-07-01

A review of the physical properties of metallic plutonium, its preparation, and the alloys which it forms with the main nuclear metals. Appreciation of its future as a nuclear fuel. (author) [French] Apercu sur les proprietes physiques du plutonium metallique, sa preparation, ses alliages avec les principaux metaux nucleaires. Consideration sur son avenir en tant que combustible nucleaire. (auteur)

Using the OSL single-aliquot regenerative-dose protocol with quartz extracted from building materials in retrospective dosimetry

International Nuclear Information System (INIS)

Boetter-Jensen, L.; Solongo, S.; Murray, A.S.; Banerjee, D.; Jungner, H.

2000-01-01

We report on the application of the single-aliquot regenerative-dose (SAR) protocol to the optically stimulated luminescence signal from quartz extracted from fired bricks and unfired mortar in retrospective dosimetry. The samples came from a radioactive materials storage facility, with ambient dose rates of about 0.1 mGy/h. A detailed dose-depth profile was analysed from one brick, and compared with dose records from area TL dosemeters. Small-aliquot dose-distributions were analysed from the mortar samples; one associated with the exposed brick, and one from a remote site exposed only to background radiation. We conclude that unfired materials have considerable potential in retrospective dosimetry

Fused salt processing of impure plutonium dioxide to high-purity plutonium metal

International Nuclear Information System (INIS)

Mullins, L.J.; Christensen, D.C.; Babcock, B.R.

1982-01-01

A process for converting impure plutonium dioxide (approx. 96% pure) to high-purity plutonium metal (>99.9%) was developed. The process consists of reducing the oxide to an impure plutonium metal intermediate with calcium metal in molten calcium chloride. The impure intermediate metal is cast into an anode and electrorefined to produce high-purity plutonium metal. The oxide reduction step is being done now on a 0.6-kg scale with the resulting yield being >99.5%. The electrorefining is being done on a 4.0-kg scale with the resulting yield being 80 to 85%. The purity of the product, which averages 99.98%, is essentially insensitive to the purity of the feed metal. The yield, however, is directly dependent on the chemical composition of the feed. To date, approximately 250 kg of impure oxide has been converted to pure metal by this processing sequence. The availability of impure plutonium dioxide, together with the need for pure plutonium metal, makes this sequence a valuable plutonium processing tool

Heterogeneity in small aliquots of Apolllo 15 olivine-normative basalt: Implications for breccia clast studies

Science.gov (United States)

Lindstrom, Marilyn M.; Shervais, John W.; Vetter, Scott K.

1993-01-01

Most of the recent advances in lunar petrology are the direct result of breccia pull-apart studies, which have identified a wide array of new highland and mare basalt rock types that occur only as clasts within the breccias. These rocks show that the lunar crust is far more complex than suspected previously, and that processes such as magma mixing and wall-rock assimilation were important in its petrogenesis. These studies are based on the implicit assumption that the breccia clasts, which range in size from a few mm to several cm across, are representative of the parent rock from which they were derived. In many cases, the aliquot allocated for analysis may be only a few grain diameters across. While this problem is most acute for coarse-grained highland rocks, it can also cause considerable uncertainty in the analysis of mare basalt clasts. Similar problems arise with small aliquots of individual hand samples. Our study of sample heterogeneity in 9 samples of Apollo 15 olivine normative basalt (ONB) which exhibit a range in average grain size from coarse to fine are reported. Seven of these samples have not been analyzed previously, one has been analyzed by INAA only, and one has been analyzed by XRF+INAA. Our goal is to assess the effects of small aliquot size on the bulk chemistry of large mare basalt samples, and to extend this assessment to analyses of small breccia clasts.

Integrated five station nondestructive assay system for the support of decontamination and decommissioning of a former plutonium mixed oxide fuel fabrication facility

International Nuclear Information System (INIS)

Caldwell, J.T.; Bieri, J.M.; Hastings, R.D.; Horton, W.S.; Kuckertz, T.H.; Kunz, W.E.; Plettenberg, K.; Smith, L.D.

1990-01-01

The goal of a safe, efficient and economic decontamination and decommissioning of plutonium facilities can be greatly enhanced through the intelligent use of an integrated system of nondestructive assay equipment. We have designed and fabricated such a system utilizing five separate NDA stations integrated through a single data acquisition and management personal computer-based controller. The initial station utilizes a passive neutron measurement to determine item Pu inventory to the 0.1 gm level prior to insertion into the decontamination cell. A large active neutron station integrated into the cell is used to measure decontamination effectiveness at the 10 nci/gm level. Cell Pu buildup at critical points is monitored with passive neutron detectors. An active neutron station having better than 1 mg Pu assay sensitivity is used to quantify final compacted waste pucks outside the cell. Bulk Pu in various forms and isotopic enrichments is quantified in a combined passive neutron coincidence and high resolution gamma ray spectrometer station outside the cell. Item control and Pu inventory are managed with bar code labeling and a station integrating algorithm. Overall economy is achieved by multiple station use of the same expensive hardware such as the neutron generator

Plutonium storage criteria

Energy Technology Data Exchange (ETDEWEB)

Chung, D. [Scientech, Inc., Germantown, MD (United States); Ascanio, X. [Dept. of Energy, Germantown, MD (United States)

1996-05-01

The Department of Energy has issued a technical standard for long-term (>50 years) storage and will soon issue a criteria document for interim (<20 years) storage of plutonium materials. The long-term technical standard, {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides,{close_quotes} addresses the requirements for storing metals and oxides with greater than 50 wt % plutonium. It calls for a standardized package that meets both off-site transportation requirements, as well as remote handling requirements from future storage facilities. The interim criteria document, {open_quotes}Criteria for Interim Safe Storage of Plutonium-Bearing Solid Materials{close_quotes}, addresses requirements for storing materials with less than 50 wt% plutonium. The interim criteria document assumes the materials will be stored on existing sites, and existing facilities and equipment will be used for repackaging to improve the margin of safety.

Toxicology of plutonium

International Nuclear Information System (INIS)

Bair, W.J.

1974-01-01

Data are reviewed from studies on the toxicity of Pu in experimental animals. Of the several plutonium isotopes, only 238 Pu and 239 Pu have been studied well. Sufficient results have been obtained to show that the behavior of 238 Pu in biological systems and the resulting biological effects cannot be precisely predicted from studies of 239 Pu. This probably applies also to other radiologically important plutonium isotopes which have half-lives ranging from 45 days to 10 7 years and decay by β-emission, electron capture, and spontaneous fission, as well as by emission of α-particles. All the biological effects of plutonium described in this review are attributed to alpha-particle radiation emitted by the plutonium. However, since plutonium is a chemically active heavy metal, one cannot ignore the possibility of chemical toxicity of the low-specific-activity isotopes, 239 Pu, 242 Pu, and 244 Pu. The preponderance of our knowledge of plutonium toxicology has come from short-term studies of relatively high dosage levels in several animal species. The consequences of high-level internal exposures can be predicted with confidence in experimental animals and probably also in man. However, considering the care with which plutonium is handled in the nuclear industry, a high-level contamination event is unlikely. Considerably less is known about the long-term effects of low levels of contamination. (250 references) (U.S.)

Cycle downstream: the plutonium question; Aval du cycle la question du plutonium

Energy Technology Data Exchange (ETDEWEB)

Zask, G [Electricite de France, EDF/DAC, 75 - Paris (France); Rome, M [Electricite de France, EDF, Service Etudes et Projets Thermiques et Nucleaires, 92 - Courbevoie (France); Delpech, M [CEA Cadarache, Dept. d' Etudes des Reacteurs/SPRC, 13 - Saint-Paul-lez-Durance (France); and others

1998-06-29

This day, organized by the SFEN, took place at Paris the 4 june 1998. Nine papers were presented. They take stock on the plutonium physics and its utilization as a nuclear fuel. This day tried to bring information to answer the following questions: do people have to keep the plutonium in the UOX fuel or in the MOX fuel in order to use it for future fast reactors? Do people have to continue obstinately the plutonium reprocessing in the MOX for the PWR type reactors? Will it be realized a underground disposal? Can it be technically developed plutonium incinerators and is it economically interesting? The plutonium physics, the experimental programs and the possible solutions are presented. (A.L.B.)

The handling of plutonium hexafluoride (1962); Manipulation de l'hexafluorure de plutonium (1962)

Energy Technology Data Exchange (ETDEWEB)

Berard, Ph [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1961-11-15

The major problem posed in this work is the instability of plutonium hexafluoride. The influence of various factors on the decomposition of the fluoride has been studied: physical aspect of the walls, nature of the metal and its pretreatment, influence of the temperature. A means of detecting plutonium-239 in a metallic apparatus by {gamma}-ray counting has been developed; the sensitivity is of the order of half a milligram, but the precision is very low (about 50 per cent). Yields of over 95 per cent have been obtained for the transfer of plutonium during the preparation and sublimation of the hexafluoride. This study confirms the possibility of using plutonium hexafluoride for the extraction of plutonium from irradiated fuel elements by a dry method. (author) [French] Le probleme majeur de cette etude a ete l'instabilite de l'hexafluorure de plutonium. Nous avons etudie l'influence de divers facteurs sur la decomposition de l'hexafluorure: aspect physique des parois, nature du metal et de son pretraitement, influence de la temperature. Nous avons mis au point un mode de detection du plutonium-239 dans un appareillage metallique par comptage du rayonnement {gamma}; la sensibilite est de l'ordre du demi-milligramme, mais la precision est tres faible (50 pour cent environ). Nous avons obtenu des rendements depassant 95 pour cent dans le transfert du plutonium au cours de la fabrication et de la sublimation de l'hexafluorure. Cette etude confirme la possibilite d'utiliser l'hexafluorure de plutonium dans l'extraction du plutonium des combustibles irradies par voie seche. (auteur)

Plutonium re-cycle in HTR

Energy Technology Data Exchange (ETDEWEB)

Desoisa, J. A.

1974-03-15

The study of plutonium cycles in HTRs using reprocessed plutonium from Magnox and AGR fuel cycles has shown that full core plutonium/uranium loadings are in general not feasible, burn-up is limited due the need for lower loadings of plutonium to meet reload core reactivity limits, on-line refueling is not practicable due to the need for higher burnable poison loadings, and low conversion rates in the plutonium-uranium cycles cannot be mitigated by axial loading schemes so that fissile make-up is needed if HTR plutonium recycle is desired.

PLUTONIUM-ZIRCONIUM ALLOYS

Science.gov (United States)

Schonfeld, F.W.; Waber, J.T.

1960-08-30

A series of nuclear reactor fuel alloys consisting of from about 5 to about 50 at.% zirconium (or higher zirconium alloys such as Zircaloy), balance plutonium, and having the structural composition of a plutonium are described. Zirconium is a satisfactory diluent because it alloys readily with plutonium and has desirable nuclear properties. Additional advantages are corrosion resistance, excellent fabrication propenties, an isotropie structure, and initial softness.

Optimization and plutonium equilibrium

International Nuclear Information System (INIS)

Silver, G.L.

1976-01-01

The sequential simplex method has been used to estimate the extent of disproportionation of tetravalent plutonium in dilute acid. A method for simulating potentiometric titrations is proposed, and this method suggests that the stoichiometric end point and the inflection point may not always correspond in the potentiometric titration of plutonium. A possible characteristic equation for the nitrite-plutonium reaction is illustrated, and the method of proportional equations is extended to the iron-plutonium reaction

Weapons-grade plutonium dispositioning. Volume 2: Comparison of plutonium disposition options

International Nuclear Information System (INIS)

Brownson, D.A.; Hanson, D.J.; Blackman, H.S.

1993-06-01

The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate disposition options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) offered to assist the NAS in this evaluation by investigating the technical aspects of the disposition options and their capability for achieving plutonium annihilation levels greater than 90%. This report was prepared for the NAS to document the gathered information and results from the requested option evaluations. Evaluations were performed for 12 plutonium disposition options involving five reactor and one accelerator-based systems. Each option was evaluated in four technical areas: (1) fuel status, (2) reactor or accelerator-based system status, (3) waste-processing status, and (4) waste disposal status. Based on these evaluations, each concept was rated on its operational capability and time to deployment. A third rating category of option costs could not be performed because of the unavailability of adequate information from the concept sponsors. The four options achieving the highest rating, in alphabetical order, are the Advanced Light Water Reactor with plutonium-based ternary fuel, the Advanced Liquid Metal Reactor with plutonium-based fuel, the Advanced Liquid Metal Reactor with uranium-plutonium-based fuel, and the Modular High Temperature Gas-Cooled Reactor with plutonium-based fuel. Of these four options, the Advanced Light Water Reactor and the Modular High Temperature Gas-Cooled Reactor do not propose reprocessing of their irradiated fuel. Time constraints and lack of detailed information did not allow for any further ratings among these four options. The INEL recommends these four options be investigated further to determine the optimum reactor design for plutonium disposition

Weapons-grade plutonium dispositioning. Volume 2: Comparison of plutonium disposition options

Energy Technology Data Exchange (ETDEWEB)

Brownson, D.A.; Hanson, D.J.; Blackman, H.S. [and others

1993-06-01

The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate disposition options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) offered to assist the NAS in this evaluation by investigating the technical aspects of the disposition options and their capability for achieving plutonium annihilation levels greater than 90%. This report was prepared for the NAS to document the gathered information and results from the requested option evaluations. Evaluations were performed for 12 plutonium disposition options involving five reactor and one accelerator-based systems. Each option was evaluated in four technical areas: (1) fuel status, (2) reactor or accelerator-based system status, (3) waste-processing status, and (4) waste disposal status. Based on these evaluations, each concept was rated on its operational capability and time to deployment. A third rating category of option costs could not be performed because of the unavailability of adequate information from the concept sponsors. The four options achieving the highest rating, in alphabetical order, are the Advanced Light Water Reactor with plutonium-based ternary fuel, the Advanced Liquid Metal Reactor with plutonium-based fuel, the Advanced Liquid Metal Reactor with uranium-plutonium-based fuel, and the Modular High Temperature Gas-Cooled Reactor with plutonium-based fuel. Of these four options, the Advanced Light Water Reactor and the Modular High Temperature Gas-Cooled Reactor do not propose reprocessing of their irradiated fuel. Time constraints and lack of detailed information did not allow for any further ratings among these four options. The INEL recommends these four options be investigated further to determine the optimum reactor design for plutonium disposition.

Assesment of Plutonium 238 and Plutonium 239+240 in soils of different agricultural regions of Guatemala

International Nuclear Information System (INIS)

Gutierrez Martinez, E.A.

1998-02-01

In this report an assesment and measurement of PLUTONIUM 238, PLUTONIUM 239, and PLUTONIUM 240 are made. Samples of cultivated soils in 15 provinces of Guatemala were taken. To separate plutonium isotopes a radiochemical method was made using extraction, precipitation and ionic interchange. By electrodeposition the plutonium was measured using an alpha spectroscopy by PIPS method. The radioactivity ranges from 2.84 mBq/Kg to 36.38 mBq/Kg for plutonium 238, and 8.46 mBq/Kg to 26.61 mBq/Kg for plutonium 239+240

Plutonium roundtable discussion

International Nuclear Information System (INIS)

Penneman, R.A.

1982-01-01

The roundtable discussion began with remarks by the chairman who pointed out the complicated nature of plutonium chemistry. Judging from the papers presented at this symposium, he noticed a pattern which indicated to him the result of diminished funding for investigation of basic plutonium chemistry and funding focused on certain problem areas. Dr. G.L. silver pointed to plutonium chemists' erroneous use of a simplified summary equation involving the disproportionation of Pu(EV) and their each of appreciation of alpha coefficients. To his appreciation of alpha coefficients. To his charges, Dr. J.T. Bell spoke in defense of the chemists. This discussion was followed by W.W. Schulz's comments on the need for experimental work to determine solubility data for plutonium in its various oxidation states under geologic repository conditions. Discussion then turned to plutonium pyrachemical process with Dana C. Christensen as the main speaker. This paper presents edited versions of participants' written version

Investigation of plutonium (4) hydroxoformates

International Nuclear Information System (INIS)

Andryushin, V.G.; Belov, V.A.; Galaktionov, S.V.; Kozhevnikov, P.B.; Matyukha, V.A.; Shmidt, V.S.

1982-01-01

Deposition processes of plutonium (4) hydroxoformates in the system Pu(NO 3 ) 4 -HNO 3 -HCoOH-N6 4 OH-H 2 O have been studied in pH range 0.2-10.7 at total plutonium concentration in the system 100 g/l. It is shown that under the conditions plutonium (4) hydrolysis takes place with the formation of hydroxoformates. A local maximum of plutonium (4) hydroxoformate solubility in the range pH=3.8-4.8, which is evidently conditioned by the formation of soluble formate complex of plutonium in the region, is pointed out. The basic plutonium (4) formates of the composition PuOsub(x)(OH)sub(y)(COOH)sub(4-2x-y)xnHsub(2)O, where 1,3 >=x >= 0.7, 1.7 >= y >= 1.0 and n=1.5-7.0, are singled out, their thermal stability being studied. Density of the crystals and plutonium dioxide, formed during their thermal decomposition, is measured. It is established that for plutonium (4) hydroxoformates common regularities of the influence of salt composition (OH - -, CHOO - - and H 2 O-group numbers in the mulecule) on position of temperature decomposition effects and on the density of compounds, which have been previously found during the study of thorium and plutonium hydroxosalts are observed. It is shown that the density of plutonium dioxide decreases with the increase of hydration and hydrolysis degree of the initial plutonium hydroxoformate

Diffusion in the uranium - plutonium system and self-diffusion of plutonium in epsilon phase; Diffusion dans le systeme uranium-plutonium et autodiffusion du plutonium epsilon

Energy Technology Data Exchange (ETDEWEB)

Dupuy, M [Commissariat a l' Energie Atomique, Fontenay-Aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

A survey of uranium-plutonium phase diagram leads to confirm anglo-saxon results about the plutonium solubility in {alpha} uranium (15 per cent at 565 C) and the uranium one in {zeta} phase (74 per cent at 565 C). Interdiffusion coefficients, for concentration lower than 15 per cent had been determined in a temperature range from 410 C to 640 C. They vary between 0.2 and 6 10{sup 12} cm{sup 2} s{sup -1}, and the activation energy between 13 and 20 kcal/mole. Grain boundary, diffusion of plutonium in a uranium had been pointed out by micrography, X-ray microanalysis and {alpha} autoradiography. Self-diffusion of plutonium in {epsilon} phase (bcc) obeys Arrhenius law: D = 2. 10{sup -2} exp -(18500)/RT. But this activation energy does not follow empirical laws generally accepted for other metals. It has analogies with 'anomalous' bcc metals ({beta}Zr, {beta}Ti, {beta}Hf, U{sub {gamma}}). (author) [French] Une etude du diagramme d'equilibre uranium-plutonium conduit a confirmer les resultats anglo-saxons relatifs a la solubilite du plutonium dans l'uranium {alpha} (15 pour cent a 565 C) et de l'uranium dans la phase {zeta} (74 pour cent a 565 C). Les coefficients de diffusion chimique, pour des concentrations inferieures a 15 pour cent ont ete determines a des temperatures comprises entre 410 et 640 C. Ils se situent entre 0.2 et 6. 10{sup 12} cm{sup 2} s{sup -1}. L'energie d'activation varie entre 13 et 20 kcal/mole. La diffusion intergranulaire du plutonium dans l'uranium a a ete mise en evidence par micrographie, microanalyse X et autoradiographie {alpha}. L' autodiffusion du plutonium {beta} cubique centree obeit a la loi d'Arrhenius D = 2. 10{sup -2} exp - (18500)/RT. Son energie d'activation n'obeit pas aux lois empiriques generalement admises pour les autres metaux. Elle possede des analogies avec les cubiques centres ''anormaux'' (Zr{beta}, Ti{beta}, Hf{beta}, U{gamma}). (auteur)

Comparison of single-grain and small-aliquot OSL dose estimates in < 3000 years old river sediments from South India

DEFF Research Database (Denmark)

Thomas, P.J.; Jain, M.; Juyal, N.

2005-01-01

We report on OSL dose distributions derived from small-aliquot and single grains of quartz in young fluvial sediments sampled from the Penner River basin, South India. The single-grain dose distributions suggest that 13 out of 19 samples were well bleached. In many well-bleached samples, there wa......We report on OSL dose distributions derived from small-aliquot and single grains of quartz in young fluvial sediments sampled from the Penner River basin, South India. The single-grain dose distributions suggest that 13 out of 19 samples were well bleached. In many well-bleached samples......, there was an underestimation in the single-aliquot dose estimates as compared to those from the single grain-the difference between average dose estimates determined by the two methods ranged from similar to 1% to 31%. Such a dose underestimation was not detectable in poorly bleached samples. Various possible reasons...... perhaps be one of the reasons; this may occur because the stimulation wavelength affects the proportion of the medium and slow components in the initial signal. (c) 2004 Elsevier Ltd. All rights reserved....

Extraction of uranium from alkaline medium by aliquot-336 in different diluents

Energy Technology Data Exchange (ETDEWEB)

Shehata, F A; Elnadi, Y A; Aly, H F [Hot laboratories center, atomic energy authority 13758, Cairo, (Egypt); Ahmed, A S [Faculty of science, Cairo University, Giza, (Egypt)

1995-10-01

A study was made on the extraction of uranium from aqueous solutions containing sodium carbonate and sodium hydroxide in the presence of oxidizing agent (H{sub 2} O{sub 2}) by aliquot-336 dissolved in different diluents. The effect of different factors affecting the extraction equilibrium was experimented. From the results obtained, the extraction equilibrium was elaborated. From the effect of temperature on the extraction, The thermodynamic constants of the system were determined and discussed. 5 figs., 1 tab.

Geometry-based multiplication correction for passive neutron coincidence assay of materials with variable and unknown (α,n) neutron rates

International Nuclear Information System (INIS)

Langner, D.G.; Russo, P.A.

1993-02-01

We have studied the problem of assaying impure plutonium-bearing materials using passive neutron coincidence counting. We have developed a technique to analyze neutron coincidence data from impure plutonium samples that uses the bulk geometry of the sample to correct for multiplication in samples for which the (α,n) neutron production rate is unknown. This technique can be applied to any impure plutonium-bearing material whose matrix constituents are approximately constant, whose self-multiplication is low to moderate, whose plutonium isotopic composition is known and not substantially varying, and whose bulk geometry is measurable or can be derived. This technique requires a set of reference materials that have well-characterized plutonium contents. These reference materials are measured once to derive a calibration that is specific to the neutron detector and the material. The technique has been applied to molten salt extraction residues, PuF 4 samples that have a variable salt matrix, and impure plutonium oxide samples. It is also applied to pure plutonium oxide samples for comparison. Assays accurate to 4% (1 σ) were obtained for impure samples measured in a High-Level Neutron Coincidence Counter II. The effects on the technique of variations in neutron detector efficiency with energy and the effects of neutron capture in the sample are discussed

A method for the gravimetric determination of plutonium in pure plutonium nitrate concentrate solution

International Nuclear Information System (INIS)

Mair, M.A.; Savage, D.J.

1986-12-01

Plutonium nitrate solution is treated with sulphuric acid before being heated and finally ignited. The stoichiometric plutonium dioxide so formed is weighed and hence the plutonium content is calculated. (author)

F. Biological hazards of plutonium

International Nuclear Information System (INIS)

1976-01-01

Plutonium is an unavoidable result of present nuclear power programmes. Its predominant isotopes are extremely long-lived and very toxic if absorbed in the body. In view of the increasing potential for plutonium and man to come into contact, the consequences of any plutonium release into the environment should be scientifically examined. This report is an attempt to place in one document a fully referenced account of the on-going work in many areas. There are three sections. Part 1 deals with the amounts of plutonium available in the fuel cycle, its properties and the probability of routine or accidental release. Part 2 examines the ways in which plutonium can reach man, in particular through food chains or inhalation. Part 3 details the biological effects of plutonium once it is absorbed into the body, assesses the amounts likely to be harmful and discusses the adequacy of present standards for plutonium burdens. There are two appendices. The likely differences between Pu-239, the most studied isotope, and other plutonium isotopes or transuranic nuclides are outlined in Appendix A. Appendix B contains a fuller account of the ways in which the fate of ingested or inhaled plutonium have been determined

Use of plutonium for power production

International Nuclear Information System (INIS)

1965-01-01

The panel reviewed available information on various aspects of plutonium utilization, such as physics of plutonium, technology of plutonium fuels in thermal and fast reactors, behaviour of plutonium fuel under reactor irradiation, technological and economic aspects of plutonium fuel cycle. Refs, figs and tabs

World status report: plutonium

International Nuclear Information System (INIS)

Dircks, W.

1992-01-01

In a recent speech in Japan, the Deputy Director General of the International Atomic Energy Agency (IAEA) said that the economic case for reprocessing spent nuclear fuel had been severely eroded. An edited version of the speech is given. The changed prospects for nuclear energy is given as the reason why the demand for plutonium has declined sharply. The oil crisis of the 1970s reduced the demand for electric power and the economic justification for the use of recycled plutonium. The stockpile of isolated plutonium is growing rapidly giving rise to worries about its security. From this point of view, isolated plutonium is best kept in reactor fuel not separated out. In this connection the IAEA has offered to help in the storage of plutonium so that vigorous safety and security requirements are met. In Japan there is a debate about the plutonium which is dependent on the future of the fast breeder reactor programme. (UK)

Plutonium Finishing Plant

Data.gov (United States)

Federal Laboratory Consortium — The Plutonium Finishing Plant, also known as PFP, represented the end of the line (the final procedure) associated with plutonium production at Hanford.PFP was also...

A Calibration to Predict Concentrations of Impurities in Plutonium Oxide by Prompt Gamma Analysis

International Nuclear Information System (INIS)

Narlesky, J.E.; Kelly, E.J.; Foster, L.A.

2005-01-01

Prompt gamma (PG) analysis has been used to identify the presence of certain impurities in plutonium oxide, which has been stored in 3013 containers. A regression analysis was used to evaluate the trends between the count rates obtained from PG analysis and the concentration of the impurities in plutonium oxide samples measured by analytical chemistry techniques. The results of the analysis were used to obtain calibration curves, which may be used to predict the concentration of Al, Be, Cl, F, Mg, and Na in the 3013 containers. The scatter observed in the data resulted from several factors including sample geometry, error in sampling for chemical assay, statistical counting error, and intimacy of mixing of impurities and plutonium. Standards prepared by mixing plutonium oxide with CaF 2 , NaCl, and KCl show that intimacy mixing and sampling error have the largest influence on the results. Although these factors are difficult to control, the calibrations are expected to yield semiquantitative results that are sufficient for the purpose of ordering or ranking

Double shell tanks plutonium inventory assessment

International Nuclear Information System (INIS)

Tusler, L.A.

1995-01-01

This report provides an evaluation that establishes plutonium inventory estimates for all DSTs based on known tank history information, the DST plutonium inventory tracking system, tank characterization measurements, tank transfer records, and estimated average concentration values for the various types of waste. These estimates use data through December 31, 1994, and give plutonium estimates as of January 1, 1995. The plutonium inventory values for the DSTs are given in Section 31. The plutonium inventory estimate is 224 kg for the DSTs and 854 kg for the SSTs for a total of 1078 kg. This value compares favorably with the total plutonium inventory value of 981 kg obtained from the total plutonium production minus plutonium recovery analysis estimates

Determination of plutonium in environment

International Nuclear Information System (INIS)

Sakanoue, Masanobu

1978-01-01

Past and present methods of determining the amount of plutonium in the environment are summarized. Determination of the amount of plutonium in uranium ore began in 1941. Plutonium present in polluted environments due to nuclear explosions, nuclear power stations, etc. was measured in soil and sand in Nagasaki in 1951 and in ash in Bikini in 1954. Analytical methods of measuring the least amount of plutonium in the environment were developed twenty years later. Many studies on and reviews of these methods have been reported all over the world, and a standard analytical procedure has been adopted. A basic analytical method of measurement was drafted in Japan in 1976. The yield, treatment of samples, dissolution, separation, control of measurable ray sources determination by α spectrometry, cross-check determination, and treatment of samples containing hardly soluble plutonium were examined. At present, the amount of plutonium can be determined by all of these methods. The presence of plutonium was studied further, and the usefulness of determination of the plutonium isotope ratio is discussed. (Kumagai, S.)

Multi-generational stewardship of plutonium

International Nuclear Information System (INIS)

Pillay, K.K.S.

1997-01-01

The post-cold war era has greatly enhanced the interest in the long-term stewardship of plutonium. The management of excess plutonium from proposed nuclear weapons dismantlement has been the subject of numerous intellectual discussions during the past several years. In this context, issues relevant to long-term management of all plutonium as a valuable energy resource are also being examined. While there are differing views about the future role of plutonium in the economy, there is a recognition of the environmental and health related problems and proliferation potentials of weapons-grade plutonium. The long-term management of plutonium as an energy resource will require a new strategy to maintain stewardship for many generations to come

Plutonium in the marine environment

International Nuclear Information System (INIS)

Jarvis, N.V.; Linder, P.W.; Wade, P.W.

1994-01-01

The shipping of plutonium from Europe to Japan around the Cape is a contentious issue which has raised public concern that South Africa may be at risk to plutonium exposure should an accident occur. The paper describes the containers in which the plutonium (in the form of plutonium oxide, PuO 2 ) is housed and consequences of the unlikely event of these becoming ruptured. Wind-borne pollution is considered not to be a likely scenario, with the plutonium oxide particles more likely to remain practically insoluble and sediment. Plutonium aqueous and environmental chemistry is briefly discussed. Some computer modelling whereby plutonium oxide is brought into contact with seawater has been performed and the results are presented. The impact on marine organisms is discussed in terms of studies performed at marine dump sites and after the crash of a bomber carrying nuclear warheads in Thule, Greenland in 1968. Various pathways from the sea to land are considered in the light of studies done at Sellafield, a reprocessing plant in the United Kingdom. Some recent debates in the popular scientific press, such as that on the leukemia cluster at Sellafield, are described. Plutonium biochemistry and toxicity are discussed as well as medical histories of workers exposed to plutonium. 35 refs., 2 tabs., 1 fig

Some target assay uncertainties for passive neutron coincidence counting

International Nuclear Information System (INIS)

Ensslin, N.; Langner, D.G.; Menlove, H.O.; Miller, M.C.; Russo, P.A.

1990-01-01

This paper provides some target assay uncertainties for passive neutron coincidence counting of plutonium metal, oxide, mixed oxide, and scrap and waste. The target values are based in part on past user experience and in part on the estimated results from new coincidence counting techniques that are under development. The paper summarizes assay error sources and the new coincidence techniques, and recommends the technique that is likely to yield the lowest assay uncertainty for a given material type. These target assay uncertainties are intended to be useful for NDA instrument selection and assay variance propagation studies for both new and existing facilities. 14 refs., 3 tabs

Plutonium Training Opportunities

Energy Technology Data Exchange (ETDEWEB)

Balatsky, Galya Ivanovna [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wolkov, Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-03-26

This report was created to examine the current state of plutonium training in the United States and to discover ways in which to ensure that the next generation of plutonium workers are fully qualified.

Optimizing Plutonium stock management

International Nuclear Information System (INIS)

Niquil, Y.; Guillot, J.

1997-01-01

Plutonium from spent fuel reprocessing is reused in new MOX assemblies. Since plutonium isotopic composition deteriorates with time, it is necessary to optimize plutonium stock management over a long period, to guarantee safe procurement, and contribute to a nuclear fuel cycle policy at the lowest cost. This optimization is provided by the prototype software POMAR

Treatment of plutonium contaminations

International Nuclear Information System (INIS)

Lafuma, J.

1983-01-01

Three kinds of plutonium contaminations were considered: skin contamination; contaminated wounds; contamination by inhalation. The treatment of these contaminations was studied for insoluble (oxide and metal forms) and soluble plutonium (complexes). The use of DTPA and therapeutic problems encountered with stable plutonium complexes were analyzed. The new possibilities of internal decontamination using Puchel and LICAM were evaluated [fr

Plutonium uptake by plants from soil containing plutonium-238 dioxide particles. Final report

International Nuclear Information System (INIS)

Brown, K.W.; McFarlane, J.C.

1977-05-01

Three plant species--alfalfa, lettuce, and radishes were grown in soils contaminated with plutonium-238 dioxide (238)PuO2 at concentrations of 23, 69, 92, and 342 nanocuries per gram (nCi/g). The length of exposure varied from 60 days for the lettuce and radishes to 358 days for the alfalfa. The magnitude of plutonium incorporation as indicated by the discrimination ratios for these species, after being exposed to the relatively insoluble PuO2, was similar to previously reported data using different chemical forms of plutonium. Evidence indicates that the predominant factor in plutonium uptake by plants may involve the chelation of plutonium contained in the soils by the action of compounds such as citric acid and/or other similar chelating agents released from the plant roots

Plutonium isotopes in the environment

International Nuclear Information System (INIS)

Holm, E.

1977-12-01

Determination of plutonium and americium by ion exchange and alpha-spectrometry. Deposition of global fall-out and accumulated area-content of 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu and 241 Am in central Sweden (62.3 deg N, 12.4 deg E), by using the lichen species Cladonia alpestris as bioindicator. Retention and distribution of plutonium in carpets of lichen and soil. Transfer of plutonium from lichen to reindeer and man. Absorbed dose in reindeer and man from plutonium. Basic studies of plutonium and americium in the western Mediterranean surface waters, with emphases on particulate form of the transuranics. (author)

The first metallurgical tests on plutonium; Premiers essais metallurgiques sur le plutonium

Energy Technology Data Exchange (ETDEWEB)

Grison, E; Abramson, R; Anselin, F; Monti, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Metallic plutonium was first prepared in France in January 1956, as soon as we had access to quantities of the order of several grams of plutonium, which had been extracted from the rods of the pile EL2 at Saclay. Since up to the present this reactor, of thermal power 2 000 kW, has been our only source of plutonium, we have so far only worked on experimental quantities sufficient for the basic tests but not for tests on a scale of possible applications. It is this work, carried out during this phase of preliminary research, which is described below. With the starting up of the plutonium extraction plant at Marcoule, where the reactor G1 has been operating at power for more than a year, we shall go on next to a another order of magnitude which will allow the manufacture and experimentation of prototype fuel elements. (author) [French] La premiere elaboration de plutonium metallique en France fut faite en janvier 1956, des que nous pumes disposer de quantites de plutonium de l'ordre de quelques grammes, qui avaient ete retires des barreaux de la pile EL2 de Saclay. Ce reacteur, d'une puissance thermique de 2 000 kW, ayant ete jusqu'a present notre seule source de plutonium, nous n'avons encore travaille que sur des quantites experimentales suffisantes pour les essais de base, mais non pour des essais a l'echelle d'applications possibles. Ce sont les travaux effectues pendant cette phase de recherches preliminaires qui seront evoques ci-dessous. Avec la mise eu route de l'usine d'extraction de plutonium de Marcoule, ou le reacteur G1 fonctionne en puissance depuis plus d'un an, nous allons passer prochainement a un autre ordre de grandeur, qui nous permettra la fabrication et l'experimentation d'elements combustibles prototypes. (auteur)

Plutonium oxides and uranium and plutonium mixed oxides. Carbon determination

International Nuclear Information System (INIS)

Anon.

Determination of carbon in plutonium oxides and uranium plutonium mixed oxides, suitable for a carbon content between 20 to 3000 ppm. The sample is roasted in oxygen at 1200 0 C, the carbon dioxide produced by combustion is neutralized by barium hydroxide generated automatically by coulometry [fr

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Filipy, R.E.

1985-01-01

Autoradiographic techniques with liquid photographic emulsion and cellulose nitrate track-etch film are being used to investigate the spatial distribution of inhaled plutonium in the lungs of beagle dogs exposed to cigarette smoke or to the plutonium aerosol only. More plutonium than expected was detected on the inner surfaces of bronchi, and particles were observed beneath the bronchial mucosa. 2 figures, 2 tables

Hazards of plutonium and fuel reprocessing

International Nuclear Information System (INIS)

Watson, G.M.

1978-01-01

Apart from the possibility that civil plutonium may be diverted to military use the main argument against the introduction of a plutonium economy seems to be the supposedly unmanageable biological risk attached to plutonium itself. The author points out weaknesses in many of the opponents' arguments against the increased use of plutonium and argues that current safety practices are more than adequate in handling plutonium and other radioactive materials

Methods for the assay of plutonium in vivo: what are the alternatives

International Nuclear Information System (INIS)

Rundo, J.; Strauss, M.G.; Sherman, I.S.; Brenner, R.

1976-01-01

The problem of estimating the amount of plutonium in the human body in vivo is of considerable importance in view of the major role Pu may play in the future nuclear power program. It is a particularly difficult one because the 238 Pu and 239 Pu present in reactor-grade material emit virtually no penetrating radiation, so that conventional methods of body radioactivity measurement are useless. The existing methods of estimating Pu body burdens are reviewed and alternatives are suggested. Emphasis is placed on Pu in lung, the major problem, but reference is also made to systemically deposited Pu. Both indirect and direct methods are discussed

The role of Monte Carlo burnup calculations in quantifying plutonium mass in spent fuel assemblies with non-destructive assay

Energy Technology Data Exchange (ETDEWEB)

Galloway, Jack D.; Tobin, Stephen J.; Trellue, Holly R.; Fensin, Michael L. [Los Alamos National Laboratory, Los Alamos, (United States)

2011-12-15

The Next Generation Safeguards Initiate (NGSI) of the United States Department of Energy has funded a multi-laboratory/university collaboration to quantify plutonium content in spent fuel (SF) with non-destructive assay (NDA) techniques and quantify the capability of these NDA techniques to detect pin diversions from SF assemblies. The first Monte Carlo based spent fuel library (SFL) developed for the NGSI program contained information for 64 different types of SF assemblies (four initial enrichments, burnups, and cooling times). The maximum amount of fission products allowed to still model a 17x17 Westinghouse pressurized water reactor (PWR) fuel assembly with four regions per fuel pin was modelled. The number of fission products tracked was limited by the available memory. Studies have since indicated that additional fission product inclusion and asymmetric burning of the assembly is desired. Thus, an updated SFL has been developed using an enhanced version of MCNPX, more powerful computing resources, and the Monte Carlo-based burnup code Monteburns, which links MCNPX to a depletion code and models a representative 1 Division-Slash 8 core geometry containing one region per fuel pin in the assemblies of interest, including a majority of the fission products with available cross sections. Often in safeguards, the limiting factor in the accuracy of NDA instruments is the quality of the working standard used in calibration. In the case of SF this is anticipated to also be true, particularly for several of the neutron techniques. The fissile isotopes of interest are co-mingled with neutron absorbers that alter the measured count rate. This paper will quantify how well working standards can be generated for PWR spent fuel assemblies and also describe the spatial plutonium distribution across an assembly. More specifically we will demonstrate how Monte Carlo gamma measurement simulations and a Monte Carlo burnup code can be used to characterize the emitted gamma

Plutonium spectrophotometric analysis

International Nuclear Information System (INIS)

Esteban, A.; Cassaniti, P.; Orosco, E.H.

1990-01-01

Plutonium ions in solution have absorption spectra so different that it is possible to use them for analytical purposes. Detailed studies have been performed in nitric solutions. Some very convenient methods for the determination of plutonium and its oxidation states, especially the ratios Pu(III):Pu(IV) and Pu(IV):Pu(VI) in a mixture of both, have been developed. These methods are described in this paper, including: a) Absorption spectra for plutonium (III), (IV), (VI) and mixtures. b) Relative extinction coefficients for the above mentioned species. c) Dependences of the relative extinction coefficients on the nitric acid concentration and the plutonium VI deviation from the Beer-Lambert law. The developed methods are simple and rapid and then, suitable in process control. Accuracy is improved when relative absorbance measurements are performed or controlled the variables which have effect on the spectra and extinction coefficients. (Author) [es

Plutonium safe handling

International Nuclear Information System (INIS)

Tvehlov, Yu.

2000-01-01

The abstract, prepared on the basis of materials of the IAEA new leadership on the plutonium safe handling and its storage (the publication no. 9 in the Safety Reports Series), aimed at presenting internationally acknowledged criteria on the radiation danger evaluation and summarizing the experience in the safe management of great quantities of plutonium, accumulated in the nuclear states, is presented. The data on the weapon-class and civil plutonium, the degree of its danger, the measures for provision of its safety, including the data on accident radiation consequences with the fission number 10 18 , are presented. The recommendations, making it possible to eliminate the super- criticality danger, as well as ignition and explosion, to maintain the tightness of the facility, aimed at excluding the radioactive contamination and the possibility of internal irradiation, to provide for the plutonium security, physical protection and to reduce irradiation are given [ru

Some of the properties of plutonium and the aluminium-plutonium alloy; Quelques proprietes du plutonium et de l'alliage aluminium-plutonium

Energy Technology Data Exchange (ETDEWEB)

Abramson, R; Boucher, R; Fabre, R; Monti, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1959-07-01

1- Study of the physical properties of plutonium. 1) Study of the allotropy of plutonium. a) Thermal analysis: the apparatus used and the measurement technique are briefly described. The transition point temperatures and the corresponding heats of transformation have been determined. Finally, the results of the particular study of certain transition points are given. b) Dilatometry. The dilatometric analysis of the phase changes of plutonium has been carried out by means of the Chevenard dilatometer with photographic recording. The testing conditions (heating and cooling speeds, isotherm plateaux) have been varied in order to determine accurately the characteristics of each transition, particularly the {delta} {yields} {gamma} transition on cooling. 2) Micrography of plutonium. For the accurate preparation of metallographic samples the electrolytic polishing must be rapid, which implies a mechanical polishing of excellent quality. Information is given on new attacking reagents which show the structure of the metal very clearly. 2- Study of aluminium-plutonium alloys. Comparative study of Al-Pu and Al-U alloys rich in aluminium. a) Thermal analysis. The liquids and fusion temperatures of the eutectic Al-XAl{sub 4}, have been accurately determined. From the measurement of the heats of fusion the exact composition of the eutectic alloy has been determined. b) Thermal treatments. The eutectic coalescence kinetics have been studied by a micrographic method and by following the evolution of hardness. The results obtained show that the phenomenon is more rapid in Al-Pu alloys than in Al-U alloys. c) Micrographic study of the transition XAl{sub 3} {yields} XAl{sub 4}. The peritectic reaction XAl{sub 3} + liq. {yields} XAl{sub 4} has been suppressed by quenching. The transformation of the XAl{sub 3} phase to the solid phase has been studied as well as the effect of small additions of silicon on the kinetics of this reaction. (author) [French] 1- Etude des proprietes

Alpha spectrum profiling of plutonium in leached simulated high-level radioactive waste-glass

International Nuclear Information System (INIS)

Diamond, H.; Friedman, A.M.

1981-01-01

Low-geometry X-ray spectra from /sup 239/Pu and /sup 237/Np, incorporated into simulated high-level radioactive waste-glass, were transformed into depth distributions for these elements. Changes in the depth profiles were observed for a series of static leachings in 75/degree/C water. Radiochemical assay of the leach solutions revealed that little neptunium or plutonium was leached, and that the amount leached was independent of leaching time. The depth profiles of the leached specimens showed that there was selective leaching of nonradioactive components of the glass, concentrating the remaining neptunium and plutonium in a broad zone near (but not at) the glass surface. Eventual redeposition of nonradioactive material onto the glass surface inhibited further leaching

Burning weapons-grade plutonium in reactors

International Nuclear Information System (INIS)

Newman, D.F.

1993-06-01

As a result of massive reductions in deployed nuclear warheads, and their subsequent dismantlement, large quantities of surplus weapons- grade plutonium will be stored until its ultimate disposition is achieved in both the US and Russia. Ultimate disposition has the following minimum requirements: (1) preclude return of plutonium to the US and Russian stockpiles, (2) prevent environmental damage by precluding release of plutonium contamination, and (3) prevent proliferation by precluding plutonium diversion to sub-national groups or nonweapons states. The most efficient and effective way to dispose of surplus weapons-grade plutonium is to fabricate it into fuel and use it for generation of electrical energy in commercial nuclear power plants. Weapons-grade plutonium can be used as fuel in existing commercial nuclear power plants, such as those in the US and Russia. This recovers energy and economic value from weapons-grade plutonium, which otherwise represents a large cost liability to maintain in safeguarded and secure storage. The plutonium remaining in spent MOX fuel is reactor-grade, essentially the same as that being discharged in spent UO 2 fuels. MOX fuels are well developed and are currently used in a number of LWRs in Europe. Plutonium-bearing fuels without uranium (non-fertile fuels) would require some development. However, such non-fertile fuels are attractive from a nonproliferation perspective because they avoid the insitu production of additional plutonium and enhance the annihilation of the plutonium inventory on a once-through fuel cycle

Elements of nondestructive assay (NDA) technology

International Nuclear Information System (INIS)

Hatcher, C.R.; Smith, H.

1984-01-01

A thorough introduction to nondestructive assay methods and instruments as they are applied to nuclear safeguards is presented. The general principles and major applications of NDA are discussed and situations in which NDA is particularly useful for nuclear safeguards purposes are described. Various passive and active γ-ray and neutron methods are examined and assay situations particularly suited to γ-ray techniques, or to neutron techniques are identified. The role of calorimetry in the NDA of plutonium-bearing materials is also discussed. The advantages and disadvantages of various NDA methods for different types of nuclear materials are mentioned

Process for recovery of plutonium from fabrication residues of mixed fuels consisting of uranium oxide and plutonium oxide

International Nuclear Information System (INIS)

Heremanns, R.H.; Vandersteene, J.J.

1983-01-01

The invention concerns a process for recovery of plutonium from fabrication residues of mixed fuels consisting of uranium oxide and plutonium oxide in the form of PuO 2 . Mixed fuels consisting of uranium oxide and plutonium oxide are being used more and more. The plants which prepare these mixed fuels have around 5% of the total mass of fuels as fabrication residue, either as waste or scrap. In view of the high cost of plutonium, it has been attempted to recover this plutonium from the fabrication residues by a process having a purchase price lower than the price of plutonium. The problem is essentially to separate the plutonium, the uranium and the impurities. The residues are fluorinated, the UF 6 and PuF 6 obtained are separated by selective absorption of the PuF 6 on NaF at a temperature of at least 400 0 C, the complex obtained by this absorption is dissolved in nitric acid solution, the plutonium is precipitated in the form of plutonium oxalate by adding oxalic acid, and the precipitated plutonium oxalate is calcined

METHOD OF PRODUCING PLUTONIUM TETRAFLUORIDE

Science.gov (United States)

Tolley, W.B.; Smith, R.C.

1959-12-15

A process is presented for preparing plutonium tetrafluoride from plutonium(IV) oxalate. The oxalate is dried and decomposed at about 300 deg C to the dioxide, mixed with ammonium bifluoride, and the mixture is heated to between 50 and 150 deg C whereby ammonium plutonium fluoride is formed. The ammonium plutonium fluoride is then heated to about 300 deg C for volatilization of ammonium fluoride. Both heating steps are preferably carried out in an inert atmosphere.

Destructive analysis capabilities for plutonium and uranium characterization at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Tandon, Lav; Kuhn, Kevin J.; Drake, Lawrence R.; Decker, Diana L.; Walker, Laurie F.; Colletti, Lisa M.; Spencer, Khalil J.; Peterson, Dominic S.; Herrera, Jaclyn A.; Wong, Amy S.

2010-01-01

Los Alamos National Laboratory's (LANL) Actinide Analytical Chemistry (AAC) group has been in existence since the Manhattan Project. It maintains a complete set of analytical capabilities for performing complete characterization (elemental assay, isotopic, metallic and non metallic trace impurities) of uranium and plutonium samples in different forms. For a majority of the customers there are strong quality assurance (QA) and quality control (QC) objectives including highest accuracy and precision with well defined uncertainties associated with the analytical results. Los Alamos participates in various international and national programs such as the Plutonium Metal Exchange Program, New Brunswick Laboratory's (NBL' s) Safeguards Measurement Evaluation Program (SME) and several other inter-laboratory round robin exercises to monitor and evaluate the data quality generated by AAC. These programs also provide independent verification of analytical measurement capabilities, and allow any technical problems with analytical measurements to be identified and corrected. This presentation will focus on key analytical capabilities for destructive analysis in AAC and also comparative data between LANL and peer groups for Pu assay and isotopic analysis.

Plutonium Plant, Trombay

International Nuclear Information System (INIS)

Yadav, J.S.; Agarwal, K.

2017-01-01

The journey of Indian nuclear fuel reprocessing started with the commissioning of Plutonium Plant (PP) at Trombay on 22"n"d January, 1965 with an aim to reprocess the spent fuel from research reactor CIRUS. The basic process chosen for the plant was Plutonium Uranium Reduction EXtraction (PUREX) process. In seventies, the plant was subjected to major design modifications and replacement of hardware, which later met the additional demand from research reactor DHRUVA. The augmented plutonium plant has been operating since 1983. Experience gained from this plant was very much helpful to design future reprocessing plant in the country

The toxicity of plutonium

International Nuclear Information System (INIS)

Crouse, P.L.

1994-01-01

Shipments of plutonium occasionally pass around the Cape coastal waters on its way to Japan from Europe. This invariably leads to a great deal of speculation of the dangers involved and of the extreme toxicity of plutonium, with the media and environmental groups claiming that (a) plutonium is the most toxic substance known to man, and that (b) a few kilograms of plutonium ground finely and dispersed in the atmosphere could kill every human being on earth. Comparisons with other poisons are drawn, e.g. common inorganic chemicals and biological agents. The original scare around the extraordinary toxicity of Pu seems to have started in 1974 with the claims of Tamplin and Cochran's hot particle theory about plutonium lodging in the sensitive portions of the lungs in small concentrated aggregates where they are much more effective in producing cancers. This theory, however, is regarded as thoroughly discredited by the experts in the field of radiotoxicity. 8 refs

Plutonium use in foreign countries (03)

International Nuclear Information System (INIS)

Otagaki, Takao

2004-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experiences of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2003 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which plans to recycle a part of plutonium: Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels: The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories: The data and information of plutonium inventories of foreign countries were collected. (author)

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Filipy, R.E.

1983-01-01

The major objective of this project is to obtain experimental data that are directly applicable to resolving the question of whether cigarette smokers are at greater risk than nonsmokers to potential health effects of inhaled plutonium. Because cigarette smokers constitute a large fraction of the population, a synergistic effect of plutonium and cigarette smoke might influence estimates of the health risk for plutonium and other transuranics released to the environment

Cycle downstream: the plutonium question

International Nuclear Information System (INIS)

Zask, G.; Rome, M.; Delpech, M.

1998-01-01

This day, organized by the SFEN, took place at Paris the 4 june 1998. Nine papers were presented. They take stock on the plutonium physics and its utilization as a nuclear fuel. This day tried to bring information to answer the following questions: do people have to keep the plutonium in the UOX fuel or in the MOX fuel in order to use it for future fast reactors? Do people have to continue obstinately the plutonium reprocessing in the MOX for the PWR type reactors? Will it be realized a underground disposal? Can it be technically developed plutonium incinerators and is it economically interesting? The plutonium physics, the experimental programs and the possible solutions are presented. (A.L.B.)

Aqueous Solution Chemistry of Plutonium

Energy Technology Data Exchange (ETDEWEB)

Clark, David L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-01-28

Things I have learned working with plutonium: Chemistry of plutonium is complex; Redox equilibria make Pu solution chemistry particularly challenging in the absence of complexing ligands; Understanding this behavior is key to successful Pu chemistry experiments; There is no suitable chemical analog for plutonium.

Plutonium Proliferation: The Achilles Heel of Disarmament

International Nuclear Information System (INIS)

Leventhal, Paul

2001-01-01

Plutonium is a byproduct of nuclear fission, and it is produced at the rate of about 70 metric tons a year in the world's nuclear power reactors. Concerns about civilian plutonium ran high in the 1970s and prompted enactment of the Nuclear Non-Proliferation Act of 1978 to give the United States a veto over separating plutonium from U.S.-supplied uranium fuel. Over the years, however, so-called reactor-grade plutonium has become the orphan issue of nuclear non-proliferation, largely as a consequence of pressures from plutonium-separating countries. The demise of the fast breeder reactor and the reluctance of utilities to introduce plutonium fuel in light-water reactors have resulted in large surpluses of civilian, weapons-usable plutonium, which now approach in size the 250 tons of military plutonium in the world. Yet reprocessing of spent fuel for recovery and use of plutonium proceeds apace outside the United States and threatens to overwhelm safeguards and security measures for keeping this material out of the hands of nations and terrorists for weapons. A number of historical and current developments are reviewed to demonstrate that plutonium commerce is undercutting efforts both to stop the spread of nuclear weapons and to work toward eliminating existing nuclear arsenals. These developments include the breakdown of U.S. anti-plutonium policy, the production of nuclear weapons by India with Atoms-for-Peace plutonium, the U.S.-Russian plan to introduce excess military plutonium as fuel in civilian power reactors, the failure to include civilian plutonium and bomb-grade uranium in the proposed Fissile Material Cutoff Treaty, and the perception of emerging proliferation threats as the rationale for development of a ballistic missile defense system. Finally, immobilization of separated plutonium in high-level waste is explored as a proliferation-resistant and disarmament-friendly solution for eliminating excess stocks of civilian and military plutonium.

An autoradiographical method using an imaging plate for the analyses of plutonium contamination in a plutonium handling facility

International Nuclear Information System (INIS)

Takasaki, Koji; Sagawa, Naoki; Kurosawa, Shigeyuki; Mizuniwa, Harumi

2011-01-01

An autoradiographical method using an imaging plate (IP) was developed to analyze plutonium contamination in a plutonium handling facility. The IPs were exposed to ten specimens having a single plutonium particle. Photostimulated luminescence (PSL) images of the specimens were taken using a laser scanning machine. One relatively large spot induced by α-radioactivity from plutonium was observed in each PSL image. The plutonium-induced spots were discriminated by a threshold derived from background and the size of the spot. A good relationship between the PSL intensities of the spots and α-radioactivities measured using a radiation counter was obtained by least-square fitting, taking the fading effect into consideration. This method was applied to workplace monitoring in an actual uranium-plutonium mixed oxide (MOX) fuel fabrication facility. Plutonium contaminations were analyzed in ten other specimens having more than two plutonium spots. The α-radioactivities of plutonium contamination were derived from the PSL images and their relative errors were evaluated from exposure time. (author)

Recovery of plutonium by pyroredox processing

International Nuclear Information System (INIS)

McNeese, J.A.; Bowersox, D.F.; Christensen, D.C.

1985-09-01

Using pyrochemical oxidation and reduction, we have developed a process to recover the plutonium in impure scrap with less than 95% plutonium. This plutonium metal was further purified by pyrochemical electrorefining. During development of the procedures, depleted electrorefining anodes were processed, and over 80% of the plutonium was recovered as high-purity metal in one electrorefining cycle. Over 40 kg of plutonium has been recovered from 55 kg of impure anodes with our procedures. 6 refs., 7 figs., 4 tabs

Recovery of plutonium by pyroredox processing

International Nuclear Information System (INIS)

McNeese, J.A.; Bowersox, D.F.; Christensen, D.C.

1985-01-01

Using pyrochemical oxidation and reduction, we have developed a process to recover the plutonium in impure scrap with less than 95% plutonium. This plutonium metal was further purified by pyrochemical electrorefining. During development of the procedures, depleted electrorefining anodes were processed, and over 80% of the plutonium was recovered as high-purity metal in one electrorefining cycle. Over 40 kg of plutonium has been recovered from 55 kg of impure anodes with our procedures. 6 refs., 2 figs., 5 tabs

Analytic determination of plutonium in the environment; Determination analytique du plutonium dans l'environnement

Energy Technology Data Exchange (ETDEWEB)

Ballada, J [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

The work described in this report was undertaken with a view to determining the plutonium content in the fall-out from nuclear explosions. In the first part are described in turn the importance of the problems due to the plutonium, the physico-chemical properties of the radioelement and the biological dangers which it presents. A detailed and critical analysis is made of the radio-toxicological determination of the plutonium as reported in the literature prior to this report. The second part consists in the presentation of a judicious choice of techniques making it possible to determine plutonium in air, rain-water, soils and ash. After a detailed description of the measurement equipment and the operational techniques which have been developed, a justification of these techniques is given with particular reference to their sensitivity and specificity. After a brief conclusion concerning the preceding chapters, the results are presented. These are then discussed in the ease of each element in which the plutonium has been determined. This discussion is concluded by a consideration of the importance of the occurrence of fall-out plutonium on problems relating to public health. From a consideration of 200 analyses carried out, it is concluded that the contribution of plutonium to the exposure of populations is still very small compared to that of natural radiation and that due to such fission products as strontium 90. The report includes 63 literature references, 26 figures and 11 tables. (author) [French] Les travaux decrits dans ce memoire ont ete entrepris et eflectues dans le but de mettre en evidence le plutonium des retombees radioactives consecutives aux explosions nucleaires. Dans la premiere partie nous etudions successivement l'importance des problemes poses par le plutonium puis les proprietes physicochimiques du radioelement et les dangers qu'il presente du point de vue biologique. Nous effectuons une analyse detaillee et critique des techniques

Weapons-grade plutonium dispositioning. Volume 4

International Nuclear Information System (INIS)

Sterbentz, J.W.; Olsen, C.S.; Sinha, U.P.

1993-06-01

This study is in response to a request by the Reactor Panel Subcommittee of the National Academy of Sciences (NAS) Committee on International Security and Arms Control (CISAC) to evaluate the feasibility of using plutonium fuels (without uranium) for disposal in existing conventional or advanced light water reactor (LWR) designs and in low temperature/pressure LWR designs that might be developed for plutonium disposal. Three plutonium-based fuel forms (oxides, aluminum metallics, and carbides) are evaluated for neutronic performance, fabrication technology, and material and compatibility issues. For the carbides, only the fabrication technologies are addressed. Viable plutonium oxide fuels for conventional or advanced LWRs include plutonium-zirconium-calcium oxide (PuO 2 -ZrO 2 -CaO) with the addition of thorium oxide (ThO 2 ) or a burnable poison such as erbium oxide (Er 2 O 3 ) or europium oxide (Eu 2 O 3 ) to achieve acceptable neutronic performance. Thorium will breed fissile uranium that may be unacceptable from a proliferation standpoint. Fabrication of uranium and mixed uranium-plutonium oxide fuels is well established; however, fabrication of plutonium-based oxide fuels will require further development. Viable aluminum-plutonium metallic fuels for a low temperature/pressure LWR include plutonium aluminide in an aluminum matrix (PuAl 4 -Al) with the addition of a burnable poison such as erbium (Er) or europium (Eu). Fabrication of low-enriched plutonium in aluminum-plutonium metallic fuel rods was initially established 30 years ago and will require development to recapture and adapt the technology to meet current environmental and safety regulations. Fabrication of high-enriched uranium plate fuel by the picture-frame process is a well established process, but the use of plutonium would require the process to be upgraded in the United States to conform with current regulations and minimize the waste streams

Measurement control for plutonium isotopic measurements using gamma-ray spectrometry

International Nuclear Information System (INIS)

Fleissner, J.G.

1985-01-01

A measurement control (MC) program should be an integral part of every nondestructive assay measurement system used for the assay of special nuclear materials. This report describes an MC program for plutonium isotopic composition measurements using high-resolution gamma-ray spectroscopy. This MC program emphasizes the standardization of data collection procedures along with the implementation of internal and external measurement control checks to provide the requisite measurement quality assurance. This report also describes the implementation of the MC program in the isotopic analysis code GRPAUT. Recommendations are given concerning the importance and frequency of the various MC checks in order to ensure a successful implementation of the MC procedures for the user's application

Recovery studies for plutonium machining oil coolant

International Nuclear Information System (INIS)

Navratil, J.D.; Baldwin, C.E.

1977-01-01

Lathe coolant oil, contaminated with plutonium and having a carbon tetrachloride diluent, is generated in plutonium machining areas at Rocky Flats. A research program was initiated to determine the nature of plutonium in this mixture of oil and carbon tetrachloride. Appropriate methods then could be developed to remove the plutonium and to recycle the oil and carbon tetrachloride. Studies showed that the mixtures of spent oil and carbon tetrachloride contained particulate plutonium and plutonium species that are soluble in water or in oil and carbon tetrachloride. The particulate plutonium was removed by filtration; the nonfilterable plutonium was removed by adsorption on various materials. Laboratory-scale tests indicated the lathe-coolant oil mixture could be separated by distilling the carbon tetrachloride to yield recyclable products

Plutonium use in foreign countries (01)

International Nuclear Information System (INIS)

Otagaki, Takao

2002-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2001 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move of recycling a part of plutonium. Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign countries were collected. (author)

Plutonium use in foreign countries (99)

International Nuclear Information System (INIS)

Otagaki, Takao

2000-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 1999 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move to recycling a part of plutonium backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign counties were collected. (author)

Plutonium use in foreign countries (02)

International Nuclear Information System (INIS)

Otagaki, Takao

2003-02-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2002 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move of recycling a part of plutonium. Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oside (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign countries were collected. (author)

Plutonium use in foreign countries. (04)

International Nuclear Information System (INIS)

Otagaki, Takao

2005-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2004 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, the U.K., Belgium, Switzerland, and Sweden which plans to recycle a limited amount of plutonium: Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels: The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories: The data and information on plutonium inventories of foreign countries were collected. (author)

Non-destructive assay of 242Pu by resonance neutron capture

International Nuclear Information System (INIS)

Kane, W.R.; Lu, Ming-Shih; Aronson, A.; Forman, L.; Vanier, P.E.

1995-01-01

For the accurate assay of plutonium by neutron correlation measurements, especially for material derived from high-burnup reactor fuel, the content of 242 Pu in a sample must be determined. Since 242 Pu has a long half-life (387,000 yr) and decays to 238 U by alpha particle emission with the accompanying emission of only weak, low-energy gamma rays, gamma-ray spectrometry methods which are ordinarily employed to determine the isotopic composition of a plutonium sample are not feasible for 242 Pu. The existence of a resonance in the neutron capture cross section of 242 Pu at an energy of 2.67 electron volts (eV) with a large (72, 000 barn) cross section affords the possibility for the quantitative assay of this isotope by epithermal neutron capture. Essential for this purpose is an appropriately designed geometry of neutron moderators and absorbers which will provide maximum flux in the eV region while suppressing thermal neutron capture by the fissile plutonium isotopes. Signatures for neutron capture in 242 Pu include the decay of 243 Pu (4.9 hr), prompt capture gamma rays (total energy 5.034 MeV), and the decay of an isomeric state (330 nanosecond). Experiments to determine the feasibility of this approach are currently in progress

Laboratory-scale evaluations of alternative plutonium precipitation methods

International Nuclear Information System (INIS)

Martella, L.L.; Saba, M.T.; Campbell, G.K.

1984-01-01

Plutonium(III), (IV), and (VI) carbonate; plutonium(III) fluoride; plutonium(III) and (IV) oxalate; and plutonium(IV) and (VI) hydroxide precipitation methods were evaluated for conversion of plutonium nitrate anion-exchange eluate to a solid, and compared with the current plutonium peroxide precipitation method used at Rocky Flats. Plutonium(III) and (IV) oxalate, plutonium(III) fluoride, and plutonium(IV) hydroxide precipitations were the most effective of the alternative conversion methods tested because of the larger particle-size formation, faster filtration rates, and the low plutonium loss to the filtrate. These were found to be as efficient as, and in some cases more efficient than, the peroxide method. 18 references, 14 figures, 3 tables

The plutonium danger

International Nuclear Information System (INIS)

Ruiter, W. de

1983-01-01

Nobody can ignore the fact that plutonium is potentially very dangerous and the greatest danger concerning it lies in the spreading of nuclear weapons via nuclear energy programmes. The following seven different attitudes towards this problem are presented and discussed: 1) There is no connection between peaceful and military applications; 2) The problem cannot be prevented; 3) A technical solution must be found; 4) plutonium must be totally inaccessible to countries involved in acquiring nuclear weapons; 5) The use of plutonium for energy production should only occur in one multinational centre; 6) Dogmas in the nuclear industry must be enfeebled; 7) All developments in this area should stop. (C.F.)

Nondestructive Assay Data Integration with the SKB-50 Assemblies - FY16 Update

International Nuclear Information System (INIS)

Tobin, Stephen Joseph; Fugate, Michael Lynn; Trellue, Holly Renee; DeBaere, Paul; Sjoland, Anders; Liljenfeldt, Henrik; Hu, Jianwei; Backstrom, Ulrika; Bengtsson, Martin; Burr, Tomas; Eliasson, Annika; Favalli, Andrea; Gauld, Ian; Grogan, Brandon; Jansson, Peter; Junell, Henrik; Schwalbach, Peter; Vaccaro, Stefano; Vo, Duc Ta; Wildestrand, Henrik

2016-01-01

A project to research the application of non-destructive assay (NDA) techniques for spent fuel assemblies is underway at the Central Interim Storage Facility for Spent Nuclear Fuel (for which the Swedish acronym is Clab) in Oskarshamn, Sweden. The research goals of this project contain both safeguards and non-safeguards interests. These nondestructive assay (NDA) technologies are designed to strengthen the technical toolkit of safeguard inspectors and others to determine the following technical goals more accurately; Verify initial enrichment, burnup, and cooling time of facility declaration for spent fuel assemblies; Detect replaced or missing pins from a given spent fuel assembly to confirm its integrity; and Estimate plutonium mass and related plutonium and uranium fissile mass parameters in spent fuel assemblies. Estimate heat content, and measure reactivity (multiplication).

Nondestructive Assay Data Integration with the SKB-50 Assemblies - FY16 Update

Energy Technology Data Exchange (ETDEWEB)

Tobin, Stephen Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fugate, Michael Lynn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Trellue, Holly Renee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); DeBaere, Paul [DG Energy, Luxembourg (Germany); Sjoland, Anders [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Liljenfeldt, Henrik [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hu, Jianwei [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Backstrom, Ulrika [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Vattenfall AB, Stockholm (Sweden); Bengtsson, Martin [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Vattenfall AB, Stockholm (Sweden); Burr, Tomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); International Atomic Energy Agency, Vienna (Austria); Eliasson, Annika [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Favalli, Andrea [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gauld, Ian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Grogan, Brandon [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jansson, Peter [Uppsala Univ. (Sweden); Junell, Henrik [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Schwalbach, Peter [DG Energy, Luxembourg (Germany); Vaccaro, Stefano [DG Energy, Luxembourg (Germany); Vo, Duc Ta [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wildestrand, Henrik [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Vattenfall AB, Stockholm (Sweden)

2016-10-28

A project to research the application of non-destructive assay (NDA) techniques for spent fuel assemblies is underway at the Central Interim Storage Facility for Spent Nuclear Fuel (for which the Swedish acronym is Clab) in Oskarshamn, Sweden. The research goals of this project contain both safeguards and non-safeguards interests. These nondestructive assay (NDA) technologies are designed to strengthen the technical toolkit of safeguard inspectors and others to determine the following technical goals more accurately; Verify initial enrichment, burnup, and cooling time of facility declaration for spent fuel assemblies; Detect replaced or missing pins from a given spent fuel assembly to confirm its integrity; and Estimate plutonium mass and related plutonium and uranium fissile mass parameters in spent fuel assemblies. Estimate heat content, and measure reactivity (multiplication).

A weighted least-squares lump correction algorithm for transmission-corrected gamma-ray nondestructive assay

International Nuclear Information System (INIS)

Prettyman, T.H.; Sprinkle, J.K. Jr.; Sheppard, G.A.

1993-01-01

With transmission-corrected gamma-ray nondestructive assay instruments such as the Segmented Gamma Scanner (SGS) and the Tomographic Gamma Scanner (TGS) that is currently under development at Los Alamos National Laboratory, the amount of gamma-ray emitting material can be underestimated for samples in which the emitting material consists of particles or lumps of highly attenuating material. This problem is encountered in the assay of uranium and plutonium-bearing samples. To correct for this source of bias, we have developed a least-squares algorithm that uses transmission-corrected assay results for several emitted energies and a weighting function to account for statistical uncertainties in the assay results. The variation of effective lump size in the fitted model is parameterized; this allows the correction to be performed for a wide range of lump-size distributions. It may be possible to use the reduced chi-squared value obtained in the fit to identify samples in which assay assumptions have been violated. We found that the algorithm significantly reduced bias in simulated assays and improved SGS assay results for plutonium-bearing samples. Further testing will be conducted with the TGS, which is expected to be less susceptible than the SGS to systematic source of bias

Studies on O/M ratio determination in uranium oxide, plutonium oxide and uranium-plutonium mixed oxide

International Nuclear Information System (INIS)

Sampath, S.; Chawla, K.L.

1975-01-01

Thermogravimetric studies were carried out in unsintered and sintered samples of uranium oxide, plutonium oxide and uranium-plutonium mixed oxide under different atmospheric conditions (air, argon and moist argon/hydrogen). Moisture loss was found to occur below 200 0 C for uranium dioxide samples, upto 700 0 C for sintered plutonium dioxide and negligible for sintered samples. The O/M ratios for non-stoichiometric uranium dioxide (sintered and unsintered), plutonium dioxide and mixed uranium and plutonium oxides (sintered) could be obtained with a precision of +- 0.002. Two reference states UOsub(2.000) and UOsub(2.656) were obtained for uranium dioxide and the reference state MOsub(2.000) was used for other cases. For unsintered plutonium dioxide samples, accurate O/M ratios could not be obtained of overlap of moisture loss with oxygen loss/gain. (author)

The plutonium challenge for the future

International Nuclear Information System (INIS)

Gray, L.W.

2000-01-01

In this paper author deal with the weapons-usable plutonium and with the possibilities of their managing. Russia has not disclosed the amount of plutonium produced, but various estimates indicate that the production was about 130 tonnes. Production has been curtailed in Russia; three dual-purpose reactors still produce weapons-grade plutonium - two at Tomsk-7 (renamed Seversk) and one at Krasnoyarsk-26 (renamed Zheleznogorsk Mining and Chemical Combine). In a 1994 United States-Russian agreement that has yet to enter into force, Russia agreed to close the remaining operating reactors by the year 2000. Treaties between the United States and Russia have already cut the number of nuclear warheads from more than 10,000 to about 6,000 under START 1, which has been ratified, and to about 3,500 under START 2, which still awaits approval. If Russia and the United States conclude START 3, that number could drop to between 2,000 and 2,500. On September 2, 1998, the Presidents of the United States and Russia signed the 'Joint statement of principles for Management and Disposition of Plutonium, Designated as No Longer Required for Defense Purposes.' In this joint statement the Presidents affirm the intention of each country to remove by stages approximately 50 metric tons of plutonium and to convert the nuclear weapons programs, and to convert this material so that it can never be used in nuclear weapons. These 100 tonne of plutonium must be managed in proper way such that it becomes neither a proliferation for an environmental risk. The United States has proposed that it manage it's 50 tonnes by a dual approach-once through MOX burning of a portion of the plutonium and immobilization in a ceramic matrix followed by en- casement in high level waste glass. Russia has proposed that it manage its full 50 tonnes by burning in a reactor. The MOX program in the United States would bum the cleaner plutonium metal and residues. Weapons components would be converted to plutonium oxide

Method to manufacture a nuclear fuel from uranium-plutonium monocarbide or uranium-plutonium mononitride

International Nuclear Information System (INIS)

Krauth, A.; Mueller, N.

1977-01-01

Pure uranium carbide or nitride is converted with plutonium oxide and carbon (all in powder form) to uranium-plutonium monocarbide or mononitride by cold pressing and sintering at about 1600 0 C. Pure uranium carbide or uranium nitride powder is firstly prepared without extensive safety measures. The pure uranium carbide or nitride powder can also be inactivated by using chemical substances (e.g. stearic acid) and be handled in air. The sinterable uranium carbide or nitride powder (or also granulate) is then introduced into the plutonium line and mixed with a nonstoichiometrically adjusted, prereacted mixture of plutonium oxide and carbon, pressed to pellets and reaction sintered. The surface of the uranium-plutonium carbide (higher metal content) can be nitrated towards the end of the sinter process in a stream of nitrogen. The protective layer stabilizes the carbide against the water and oxygen content in air. (IHOE) [de

Monitoring the risks of plutonium

International Nuclear Information System (INIS)

Holliday, B.

1978-01-01

The difficulties in monitoring the environment in work areas where plutonium is handled are identified and both continuous and personal air sampling techniques considered. Methods of estimating the amounts of plutonium retained in the body are: (1) Direct external counting over the chest of the 'soft' low energy X-rays and gamma rays emitted by the plutonium deposited in the lungs. (2) Measuring plutonium excreted in urine. (3) Analysing faeces soon after a suspected contamination. Limitation of these techniques are discussed and it is shown that estimating the amount of plutonium in the body, or a specific organ, is extremely difficult, both because of the lack of sensitivity of the measuring techniques (especially chest scanning) and because of the problems in interpreting data, stemming from a lack of knowledge of crucial characteristics of the inhaled plutonium (such as particle size and solubility). Nevertheless it is felt that the judicious integration of all the options creates a level of certainty that no individual technique can possibly inspire. (U.K.)

Progress on plutonium stabilization

Energy Technology Data Exchange (ETDEWEB)

Hurt, D. [Defense Nuclear Facilities Safety Board, Washington, DC (United States)

1996-05-01

The Defense Nuclear Facilities Safety Board has safety oversight responsibility for most of the facilities where unstable forms of plutonium are being processed and packaged for interim storage. The Board has issued recommendations on plutonium stabilization and has has a considerable influence on DOE`s stabilization schedules and priorities. The Board has not made any recommendations on long-term plutonium disposition, although it may get more involved in the future if DOE develops plans to use defense nuclear facilities for disposition activities.

Progress on plutonium stabilization

International Nuclear Information System (INIS)

Hurt, D.

1996-01-01

The Defense Nuclear Facilities Safety Board has safety oversight responsibility for most of the facilities where unstable forms of plutonium are being processed and packaged for interim storage. The Board has issued recommendations on plutonium stabilization and has has a considerable influence on DOE's stabilization schedules and priorities. The Board has not made any recommendations on long-term plutonium disposition, although it may get more involved in the future if DOE develops plans to use defense nuclear facilities for disposition activities

Excess Weapons Plutonium Immobilization in Russia

International Nuclear Information System (INIS)

Jardine, L.; Borisov, G.B.

2000-01-01

The joint goal of the Russian work is to establish a full-scale plutonium immobilization facility at a Russian industrial site by 2005. To achieve this requires that the necessary engineering and technical basis be developed in these Russian projects and the needed Russian approvals be obtained to conduct industrial-scale immobilization of plutonium-containing materials at a Russian industrial site by the 2005 date. This meeting and future work will provide the basis for joint decisions. Supporting R and D projects are being carried out at Russian Institutes that directly support the technical needs of Russian industrial sites to immobilize plutonium-containing materials. Special R and D on plutonium materials is also being carried out to support excess weapons disposition in Russia and the US, including nonproliferation studies of plutonium recovery from immobilization forms and accelerated radiation damage studies of the US-specified plutonium ceramic for immobilizing plutonium. This intriguing and extraordinary cooperation on certain aspects of the weapons plutonium problem is now progressing well and much work with plutonium has been completed in the past two years. Because much excellent and unique scientific and engineering technical work has now been completed in Russia in many aspects of plutonium immobilization, this meeting in St. Petersburg was both timely and necessary to summarize, review, and discuss these efforts among those who performed the actual work. The results of this meeting will help the US and Russia jointly define the future direction of the Russian plutonium immobilization program, and make it an even stronger and more integrated Russian program. The two objectives for the meeting were to: (1) Bring together the Russian organizations, experts, and managers performing the work into one place for four days to review and discuss their work with each other; and (2) Publish a meeting summary and a proceedings to compile reports of all the

Plutonium use - Present status and prospects

International Nuclear Information System (INIS)

Dievoet, J. van; Fossoul, E.; Jonckheere, E.; Bemden, E. van den

1977-01-01

The use of plutonium in thermal and fast reactors is a demonstrated, if not proven, technology. Moreover, plutonium is being produced in increasing quantities. Evaluation of this production on a world scale shows that it would be theoretically possible to construct numerous breeders and thus to make the best use of plutonium, while considerably reducing uranium consumption. This source of plutonium is nevertheless dependent on the reprocessing of irradiated fuel. Long delays in installing and adequate world reprocessing capacity are weakening the prospects for introducing breeders. Furthermore, the critical situation regarding reprocessing may delay the development of complementary reprocessing methods for fuels with a high plutonium content and high burnup. The recycling of plutonium is now a well-known technique and any objections to it hardly bear analysis. Utilization of plutonium offers an appreciable saving in terms of uranium and separative work units; and it can also be shown that immediate reprocessing of the recycling fuel is not essential for the economics of the concept. Temporary storage of recycled fuel is a particularly safe form of concentrating plutonium, namely in irradiated plutonium-bearing fuel assemblies. Finally, recycling offers such flexibility that it represents no obstacle to fuel management at power plants with light-water reactors. These strategic considerations imply that the technology of using plutonium for fabricating thermal or fast reactor fuels is both technically reliable and economically viable. The methods used in industrial facilities are fully reassuring in this respect. Although various unsolved problems exist, none seems likely to impede current developments, while the industrial experience gained has enabled the economics and reliability of the methods to be improved appreciably. Apart from the techno-economic aspects, the plutonium industry must face extremely important problems in connection with the safety of personnel

Plutonium recovery from carbonate wash solutions

International Nuclear Information System (INIS)

Gray, J.H.; Reif, D.J.; Chostner, D.F.; Holcomb, H.P.

1991-01-01

540Periodically higher than expected levels of plutonium are found in carbonate solutions used to wash second plutonium cycle solvent. The recent accumulation of plutonium in carbonate wash solutions has led to studies to determine the cause of that plutonium accumulation, to evaluate the quality of all canyon solvents, and to develop additional criteria needed to establish when solvent quality is acceptable. Solvent from three canyon solvent extraction cycles was used to evaluate technology required to measure tributyl phosphate (TBP) degradation products and was used to evaluate solvent quality criteria during the development of plutonium recovery processes. 1 fig

Solubility of plutonium from rumen contents of cattle grazing on plutonium-contaminated desert vegetation in in vitro bovine gastrointestinal fluids

International Nuclear Information System (INIS)

Barth, J.

1975-01-01

Rumen contents of cattle grazing on plutonium-contaminated desert vegetation at the Nevada Test Site were incubated in simulated bovine gastrointestinal fluids to study the alimentary solubility of plutonium. Trials were run during November 1973, and during February, May, July and August 1974. During the May and July trials, a large increase in plutonium solubility accompanied by a marked reduction in plutonium concentration of the rumen contents was observed concurrently with a reduction in intake of Eurotia lanata and an increase in the intake of Oryzopsis hymenoides or Sitanion jubatum. However, during the November, February, and August trials, comparatively high concentration of plutonium, but low plutonium solubility, was associated with high levels of Eurotia lanata in the rumen contents. Plutonium-238 was generally more soluble than plutonium-239 in these fluids. Ratios of the percentage of soluble plutonium-238 to the percentage of soluble plutonium-239 varied fro []1:1 to 18:1 on a radioactivity basis. (auth)

Plutonium metal burning facility

International Nuclear Information System (INIS)

Hausburg, D.E.; Leebl, R.G.

1977-01-01

A glove-box facility was designed to convert plutonium skull metal or unburned oxide to an oxide acceptable for plutonium recovery and purification. A discussion of the operation, safety aspects, and electrical schematics are included

Analytic determination of plutonium in the environment; Determination analytique du plutonium dans l'environnement

Energy Technology Data Exchange (ETDEWEB)

Ballada, J. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

The work described in this report was undertaken with a view to determining the plutonium content in the fall-out from nuclear explosions. In the first part are described in turn the importance of the problems due to the plutonium, the physico-chemical properties of the radioelement and the biological dangers which it presents. A detailed and critical analysis is made of the radio-toxicological determination of the plutonium as reported in the literature prior to this report. The second part consists in the presentation of a judicious choice of techniques making it possible to determine plutonium in air, rain-water, soils and ash. After a detailed description of the measurement equipment and the operational techniques which have been developed, a justification of these techniques is given with particular reference to their sensitivity and specificity. After a brief conclusion concerning the preceding chapters, the results are presented. These are then discussed in the ease of each element in which the plutonium has been determined. This discussion is concluded by a consideration of the importance of the occurrence of fall-out plutonium on problems relating to public health. From a consideration of 200 analyses carried out, it is concluded that the contribution of plutonium to the exposure of populations is still very small compared to that of natural radiation and that due to such fission products as strontium 90. The report includes 63 literature references, 26 figures and 11 tables. (author) [French] Les travaux decrits dans ce memoire ont ete entrepris et eflectues dans le but de mettre en evidence le plutonium des retombees radioactives consecutives aux explosions nucleaires. Dans la premiere partie nous etudions successivement l'importance des problemes poses par le plutonium puis les proprietes physicochimiques du radioelement et les dangers qu'il presente du point de vue biologique. Nous effectuons une analyse detaillee et critique des techniques

Solvent anode for plutonium purification

International Nuclear Information System (INIS)

Bowersox, D.F.; Fife, K.W.; Christensen, D.C.

1986-01-01

The purpose of this study is to develop a technique to allow complete oxidation of plutonium from the anode during plutonium electrorefining. This will eliminate the generation of a ''spent'' anode heel which requires further treatment for recovery. Our approach is to employ a solvent metal in the anode to provide a liquid anode pool throughout electrorefining. We use molten salts and metals in ceramic crucibles at 700 0 C. Our goal is to produce plutonium metal at 99.9% purity with oxidation and transfer of more than 98% of the impure plutonium feed metal from the anode into the salt and product phases. We have met these criteria in experiments on the 100 to 1000 g scale. We plan to scale our operations to 4 kg of feed plutonium and to optimize the process parameters

Design-Only Conceptual Design Report: Plutonium Immobilization Plant

International Nuclear Information System (INIS)

DiSabatino, A.; Loftus, D.

1999-01-01

This design-only conceptual design report was prepared to support a funding request by the Department of Energy Office of Fissile Materials Disposition for engineering and design of the Plutonium Immobilization Plant, which will be used to immobilize up to 50 tonnes of surplus plutonium. The siting for the Plutonium Immobilization Plant will be determined pursuant to the site-specific Surplus Plutonium Disposition Environmental Impact Statement in a Plutonium Deposition Record of Decision in early 1999. This document reflects a new facility using the preferred technology (ceramic immobilization using the can-in-canister approach) and the preferred site (at Savannah River). The Plutonium Immobilization Plant accepts plutonium from pit conversion and from non-pit sources and, through a ceramic immobilization process, converts the plutonium into mineral-like forms that are subsequently encapsulated within a large canister of high-level waste glass. The final immobilized product must make the plutonium as inherently unattractive and inaccessible for use in nuclear weapons as the plutonium in spent fuel from commercial reactors and must be suitable for geologic disposal. Plutonium immobilization at the Savannah River Site uses: (1) A new building, the Plutonium Immobilization Plant, which will convert non-pit surplus plutonium to an oxide form suitable for the immobilization process, immobilize plutonium in a titanate-based ceramic form, place cans of the plutonium-ceramic forms into magazines, and load the magazines into a canister; (2) The existing Defense Waste Processing Facility for the pouring of high-level waste glass into the canisters; and (3) The Actinide Packaging and Storage Facility to receive and store feed materials. The Plutonium Immobilization Plant uses existing Savannah River Site infra-structure for analytical laboratory services, waste handling, fire protection, training, and other support utilities and services. The Plutonium Immobilization Plant

Elements of nondestructive assay (NDA) technology

International Nuclear Information System (INIS)

Anon.

1981-01-01

This session provides an introduction to nondestructive assay methods and instruments as they are applied to nuclear safeguards. The purpose of the sessions is to enable participants to: (1) discuss the general principles and major applications of NDA; (2) describe situations in which NDA is particularly useful for nuclear safeguards purposes; (3) distinguish between various passive and active gamma-ray and neutron NDA methods; (4) describe several NDA instruments that measure gamma rays, and identify assay situations particularly suited to gamma-ray techniques; (5) describe several NDA instruments that measure neutrons, and identify assay situations particularly suited to neutron techniques; (6) discuss the role of calorimetry in the NDA of plutonium-bearing materials; and (7) compare the advantages and disadvantages of various NDA methods for different types of nuclear materials

Bibliography on plutonium and its compounds; Bibliographie sur le plutonium et ses composes

Energy Technology Data Exchange (ETDEWEB)

Dirian, J; Choquet, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Collection of bibliographical references on plutonium and its principal compounds from 1942 to end of 1957. (author) [French] Compilation de references bibliographiques sur le plutonium et ses principaux composes de 1942 a fin 1957. (auteur)

Plutonium speciation affected by environmental bacteria

International Nuclear Information System (INIS)

Neu, M.P.; Icopini, G.A.; Boukhalfa, H.

2005-01-01

Plutonium has no known biological utility, yet it has the potential to interact with bacterial cellular and extracellular structures that contain metal-binding groups, to interfere with the uptake and utilization of essential elements, and to alter cell metabolism. These interactions can transform plutonium from its most common forms, solid, mineral-adsorbed, or colloidal Pu(IV), to a variety of biogeochemical species that have much different physico-chemical properties. Organic acids that are extruded products of cell metabolism can solubilize plutonium and then enhance its environmental mobility, or in some cases facilitate plutonium transfer into cells. Phosphate- and carboxylate-rich polymers associated with cell walls can bind plutonium to form mobile biocolloids or Pu-laden biofilm/mineral solids. Bacterial membranes, proteins or redox agents can produce strongly reducing electrochemical zones and generate molecular Pu(III/IV) species or oxide particles. Alternatively, they can oxidize plutonium to form soluble Pu(V) or Pu(VI) complexes. This paper reviews research on plutonium-bacteria interactions and closely related studies on the biotransformation of uranium and other metals. (orig.)

Plutonium vulnerability issues at Hanford's Plutonium Finishing Plant

International Nuclear Information System (INIS)

Feldt, E.; Templeton, D.W.; Tholen, E.

1995-01-01

The Plutonium Finishing Plant (PFP) at the Hanford, Washington Site was operated to produce plutonium (Pu) metal and oxide for national defense purposes. Due to the production requirements and methods utilized to meet national needs and the abrupt shutdown of the plant in the late 1980s, the plant was left in a condition that poses a risk of radiation exposure to plant workers, of accidental radioactive material release to the environment, and of radiation exposure to the public. In early 1994, an Environmental Impact Statement (EIS) to determine the best methods for cleaning out and stabilizing Pu materials in the PFP was started. While the EIS is being prepared, a number of immediate actions have been completed or are underway to significantly reduce the greatest hazards in the PFP. Recently, increased attention his been paid to Pu risks at Department of Energy (DOE) facilities resulting in the Department-wide Plutonium Vulnerability Assessment and a recommendation by the Defense Nuclear Facilities Safety Board (DNFSB) for DOE to develop integrated plans for managing its nuclear materials

Physics of Plutonium Recycling in Thermal Reactors

International Nuclear Information System (INIS)

Kinchin, G.H.

1967-01-01

A substantial programme of experimental reactor physics work with plutonium fuels has been carried out in the UK; the purpose of this paper is to review the experimental and theoretical work, with emphasis on plutonium recycling in thermal reactors. Although the main incentive for some of the work may have been to study plutonium build-up in uranium-fuelled reactors, it is nevertheless relevant to plutonium recycling and no distinction is drawn between build-up and enrichment studies. A variety of techniques have been for determining reactivity, neutron spectrum and reaction rates in simple assemblies of plutonium-aluminium fuel with water, graphite and beryllia moderators. These experiments give confidence in the basic data and methods of calculation for near-homogeneous mixtures of plutonium and moderator. In the practical case of plutonium recycling it is necessary to confirm that satisfactory predictions can be made for heterogeneous lattices enriched with plutonium. In this field, experiments have been carried out with plutonium-uranium metal and oxide-cluster fuels in graphite-moderated lattices and in SGHW lattices, and the effects of 240 Pu have been studied by perturbation measurements with single fuel elements. The exponential and critical experiments have used tonne quantities of fuel with plutonium contents ranging from 0.25 to 1.2% and the perturbation experiments have extended both the range of plutonium contents and the range of isotopic compositions of plutonium. In addition to reactivity and reactivity coefficients, such as the temperature coefficients, attention has been concentrated on relative reaction rate distributions which provide evidence for variations of neutron spectrum. .Theoretical comparisons, together with similar comparisons for non-uniform lattices, establish the validity of methods of calculation which have been used to study the feasibility of plutonium recycling in thermal reactors. (author)

Physics of Plutonium Recycling in Thermal Reactors

Energy Technology Data Exchange (ETDEWEB)

Kinchin, G. H. [Atomic Energy Establishment, Winfrith, Dorchester, Dorset (United Kingdom)

1967-09-15

A substantial programme of experimental reactor physics work with plutonium fuels has been carried out in the UK; the purpose of this paper is to review the experimental and theoretical work, with emphasis on plutonium recycling in thermal reactors. Although the main incentive for some of the work may have been to study plutonium build-up in uranium-fuelled reactors, it is nevertheless relevant to plutonium recycling and no distinction is drawn between build-up and enrichment studies. A variety of techniques have been for determining reactivity, neutron spectrum and reaction rates in simple assemblies of plutonium-aluminium fuel with water, graphite and beryllia moderators. These experiments give confidence in the basic data and methods of calculation for near-homogeneous mixtures of plutonium and moderator. In the practical case of plutonium recycling it is necessary to confirm that satisfactory predictions can be made for heterogeneous lattices enriched with plutonium. In this field, experiments have been carried out with plutonium-uranium metal and oxide-cluster fuels in graphite-moderated lattices and in SGHW lattices, and the effects of {sup 240}Pu have been studied by perturbation measurements with single fuel elements. The exponential and critical experiments have used tonne quantities of fuel with plutonium contents ranging from 0.25 to 1.2% and the perturbation experiments have extended both the range of plutonium contents and the range of isotopic compositions of plutonium. In addition to reactivity and reactivity coefficients, such as the temperature coefficients, attention has been concentrated on relative reaction rate distributions which provide evidence for variations of neutron spectrum. .Theoretical comparisons, together with similar comparisons for non-uniform lattices, establish the validity of methods of calculation which have been used to study the feasibility of plutonium recycling in thermal reactors. (author)

Plutonium isotopic assay of reprocessing product solutions in the KfK K-edge densitometer

International Nuclear Information System (INIS)

Eberle, H.; Ottmar, H.; Matussek, P.

1985-04-01

The KfK K-edge densiometer, designed for accurate element concentration measurements using the technique of X-ray absorptiometry at the K absorption edge, provides as an additional option the possibility to determine the isotopic composition of freshly separated plutonium from an gamma-spectrometric analysis of its self-radiation. This report describes the underlying methodology and experimental procedures for the isotopic analysis in the K-edge densitometer. The paper also presents and discusses the experimental results so far obtained from routine measurements on reprocessing product solutions. (orig.)

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Filipy, R.E.

1982-01-01

The major objective of this project is to obtain experimental data that are directly applicable to resolving the question of whether cigarette smokers are at greater risk than nonsmokers to potential health effects of inhaled plutonium. Progress was made on two fronts during the past year. The autoradiographic technique developed from detection of plutonium on the interior surface of pulmonary airways (Annual Report, 1978) has been adapted to routine use in examining tracheas and bronchi of rats. Also, dogs exposed to cigarette smoke for over a year after inhalation of plutonium were killed and necropsied

Plutonium inventories for stabilization and stabilized materials

Energy Technology Data Exchange (ETDEWEB)

Williams, A.K.

1996-05-01

The objective of the breakout session was to identify characteristics of materials containing plutonium, the need to stabilize these materials for storage, and plans to accomplish the stabilization activities. All current stabilization activities are driven by the Defense Nuclear Facilities Safety Board Recommendation 94-1 (May 26, 1994) and by the recently completed Plutonium ES&H Vulnerability Assessment (DOE-EH-0415). The Implementation Plan for accomplishing stabilization of plutonium-bearing residues in response to the Recommendation and the Assessment was published by DOE on February 28, 1995. This Implementation Plan (IP) commits to stabilizing problem materials within 3 years, and stabilizing all other materials within 8 years. The IP identifies approximately 20 metric tons of plutonium requiring stabilization and/or repackaging. A further breakdown shows this material to consist of 8.5 metric tons of plutonium metal and alloys, 5.5 metric tons of plutonium as oxide, and 6 metric tons of plutonium as residues. Stabilization of the metal and oxide categories containing greater than 50 weight percent plutonium is covered by DOE Standard {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides{close_quotes} December, 1994 (DOE-STD-3013-94). This standard establishes criteria for safe storage of stabilized plutonium metals and oxides for up to 50 years. Each of the DOE sites and contractors with large plutonium inventories has either started or is preparing to start stabilization activities to meet these criteria.

Interference from radon-thoron daughters in plutonium channel of a continuous plutonium-in-air monitor

International Nuclear Information System (INIS)

Pendharkar, K.A.; Krishnamony, S.

1983-01-01

This paper summarises the results of a study conducted to define the extent of interference from the daughter products of radon/thoron to the plutonium channel of a continuous plutonium-in-air monitor. The effect on the detection limits of the instrument due to chemical form (transportable or non-transportable) and isotopic composition of plutonium aerosol are briefly discussed. (author)

Compositions of airborne plutonium-bearing particles from a plutonium finishing operation

International Nuclear Information System (INIS)

Sanders, S.M. Jr.

1976-11-01

The elemental composition of 111 plutonium-bearing particles was determined (using an electron microprobe) as part of a program to investigate the origin and behavior of the long-lived transuranic radionuclides released from fuel reprocessing facilities at the Savannah River Plant. These particles, collected from wet-cabinet and room-air exhausts from the plutonium finishing operation (JB-Line), were between 0.4 and 36 μm in diameter. Ninety-nine of the particles were found to be aggregates of various minerals and metals, six were quartz, and six were small (less than 2-μm-diameter) pieces of iron oxide. Collectively, these particles contained less minerals and more metals than natural dusts contain. The metallic constituents included elements normally not found in dusts, e.g., chromium, nickel, copper, and zinc. Concentrations of aluminum and iron exceeded those normally found in minerals. Elemental concentrations in individual particles covered a wide range: one 2-μm-diameter particle contained 97 percent NiO, a 9-μm-diameter particle contained 72 percent Cr 2 O 3 . Although the particles were selected because they produced plutonium fission tracks, the plutonium concentration was too low to be estimated by microprobe analysis in all but a 1-μm-diameter particle. This plutonium-bearing particle contained 73 percent PuO 2 by weight in combination with Fe 2 O 3 and mica; its activity was estimated at 0.17 pCi of 239 Pu

Review and Ranking of NDA Techniques to Determine Plutonium Content in Spent Fuel

International Nuclear Information System (INIS)

Cheatham, Jesse R.; Wagner, John C.

2010-01-01

A number of efforts are under way to improve nondestructive assay (NDA) techniques for spent nuclear fuel (SNF) safeguard applications. These efforts have largely focused on advancing individual NDA approaches to assay plutonium content. Although significant improvements have been made in NDA techniques, relatively little work has been done to thoroughly and systematically compare the methods. A comparative review of the relative strengths and weaknesses of current NDA techniques brings a new perspective to guide future research. To gauge the practicality and effectiveness of the various relevant NDA approaches, criteria have been developed from two broad categories: functionality and operability. The functionality category includes accuracy estimates, measurement time, plutonium verification capabilities, and assembly or fuel rod assay. Since SNF composition changes with operational history and cooling times, the viability of certain NDA approaches will also change over time. While active interrogation approaches will benefit from reduced background radiation, passive assays will lose the information contained in short-lived isotopes. Therefore, the expected assay accuracy as a function of time is considered. The operability category attempts to gauge the challenges associated with the application of different NDA techniques. This category examines the NDA deploy-ability, measurement capabilities and constraints in spent fuel pools, required on-site facilities, NDA technique synergies, and the extent to which the measurements are obtrusive to the facility. Each topic listed in the categories will be given a numerical score used to rank the different NDA approaches. While the combined numerical score of each technique is informative, the individual-topic scoring will allow for a more-tailored ranking approach. Since the needs and tools of the International Atomic Energy Agency differ from those of a recycling facility, the best assay technique may change with users

Plutonium use - present status and perspectives

International Nuclear Information System (INIS)

Dievoet, J. van; Fossoul, E.; Jonckheere, E.; Bemden, E. van den

1977-01-01

Plutonium is being produced in increasing quantities in the so-called proven reactors, which are mostly of the light-water type. Evaluation of this production on a world scale shows that it would be theoretically possible to construct a large number of breeders and thus to make the best use of the intrinsic qualities of plutonium as a fissionable material, while considerably reducing the consumption of uranium. This source of plutonium is nevertheless dependent on an essential stage of the fuel cycle, namely reprocessing of irradiated fuel. The long delays in installing an adequate world reprocessing capacity are substantially weakening the prospects for the introduction of breeders. Furthermore, the critical situation as regards reprocessing may delay the development of complementary reprocessing methods for fuels with a high plutonium content and high burn-up. When it is recalled that fast reactors themselves may suffer some delay in their technological development, if only because of the intention to build power plants of very high unit capacity immediately, it must be concluded that another use will have to be considered for the plutonium available in future -use in thermal reactors, i.e. recycling. The recycling of plutonium is a well-known technique today and the objections which could be raised against it hardly stand up to analysis. Utilization of plutonium offers an appreciable saving in terms of uranium and separative work units, the consumption being of a low order of magnitude in comparison with the total amount of plutonium needed for the eventual fabrication of the first fast reactor cores. It can also be shown that immediate reprocessing of the recycling fuel is not essential for the economics of the concept. Temporary storage of recycled fuel has the advantage of concentrating plutonium in a particularly safe form, namely in irradiated plutonium-bearing fuel assemblies. Lastly, recycling offers such flexibility that it does not in practice represent

Plutonium biokinetics in humans

International Nuclear Information System (INIS)

Popplewell, D.; Ham, G.; McCarthy, W.; Lands, C.

1994-01-01

By using an 'unusual' isotope it is possible to carry out experiments with plutonium in volunteers at minimal radiation dose levels. Measurements have been made of the gut transfer factor and the urinary excretion of plutonium after intravenous injection. (author)

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Anon.

1981-01-01

The overall objective of this study is to determine whether cigarette smoking increases the probability of plutonium-induced lung cancer. Initial experiments, designed to characterize the effect of chronic cigarette smoke exposure on pulmonary clearance of plutonium aerosols, are described

Polarographic study of the electrochemical properties of plutonium; Etude polarographique des proprietes electrochimiques du plutonium

Energy Technology Data Exchange (ETDEWEB)

Guichard, C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

The behaviour of the different degrees of oxidation of plutonium have been studied using a falling drop mercury electrode in a non-complexing medium: dilute perchloric acid. In this medium it is possible to carry out the polarographic determination of plutonium using the reduction step situated at - 0.54 V/ECS which corresponds to the passage from the degree of oxidation(V) to the degree(III). The modifications brought about by a complexing ion, acetate, are then observed and interpreted. The existence of two plutonium(IV) acetic complexes has been shown; one is a polymerized substance. (author) [French] Le comportement des differents degres d'oxydation du plutonium est etudie a l'electrode a gouttes de mercure dans un milieu non complexant: l'acide perchlorique dilue. Il est possible dans ce milieu d'effectuer le dosage polarographique du plutonium en utilisant la vague de reduction situee a - 0.54 V/ECS qui correspond au passage du degre d'oxydation(V) au degre(III). Les modifications apportees par un ion complexant, l'acetate, sont ensuite observees et interpretees. Deux complexes acetiques du plutonium(IV) ont ete mis en evidence, dont l'un est un compose polymerise. (auteur)

Plutonium working group report on environmental, safety and health vulnerabilities associated with the Department's plutonium storage. Volume I: Summary

International Nuclear Information System (INIS)

1994-11-01

At the conclusion of the Cold War, the Department of Energy (DOE) stopped plutonium processing for nuclear weapons production. Facilities used for that purpose now hold significant quantities of plutonium in various forms. Unless properly stored and handled, plutonium can present environment, safety and health (ES ampersand H) hazards. Improperly stored plutonium poses a variety of hazards. When containers or packaging fail to fully protect plutonium metal from exposure to air, oxidation can occur and cause packaging failures and personnel contamination. Contamination can also result when plutonium solutions leak from bottles, tanks or piping. Plutonium in the form of scrap or residues generated by weapons production are often very corrosive, chemically reactive and difficult to contain. Buildings and equipment that are aging, poorly maintained or of obsolete design contribute to the overall problem. Inadvertent accumulations of plutonium of any form in sufficient quantities within facilities can result in nuclear criticality events that could emit large amounts of radiation locally. Contamination events and precursors of criticality events are causing safety and health concerns for workers at the Department's plutonium facilities. Contamination events also potentially threaten the public and the surrounding environment

Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1--July 31, 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

Progress is reported on research projects related to the following: Electronic resource library; Environment, safety, and health; Communication, education, training, and community involvement; Nuclear and other materials; and Reporting, evaluation, monitoring, and administration. Technical studies investigate remedial action of high explosives-contaminated lands, radioactive waste management, nondestructive assay methods, and plutonium processing, handling, and storage.

Search for plutonium salt deposits in the plutonium extraction batteries of the Marcoule plant (1963); Recherche de depots de sels de plutonium dans les batteries d'extraction du plutonium de l'usine de Marcoule (1963)

Energy Technology Data Exchange (ETDEWEB)

Bouzigues, H; Reneaud, J M [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

1963-07-01

This report describes a method and a special apparatus making it possible to detach the insoluble plutonium salt deposits in the extraction chain of an irradiated fuel treatment plant. The process chosen allows the detection, in the extraction batteries or in the highly active chemical engineering equipment, of plutonium quantities of a few grains. After four years operation it has been impossible to detect measurable quantities of plutonium in any part of the extraction chain. The results have been confirmed by visual examinations carried out with a specially constructed endoscope. (authors) [French] Ce rapport decrit une methode et un montage special permettant de detacher les accumulations de sels de plutonium insolubles dans les chaines d'extraction d'une usine de traitement de combustible irradie. Le procede retenu permet de reperer, dans des batteries d'extraction ou dans l'appareillage de genie chimique fortement actif, des masses de plutonium de quelques grammes. Apres quatre annees de fonctionnement, il n'a pas ete possible de deceler des quantites ponderables de plutonium en aucun endroit de la chaine d'extraction. Ces resultats ont ete confirmes par les examens visuels effectues a l'aide d'un endoscope concu specialement pour cet usage. (auteurs)

A World made of Plutonium?

International Nuclear Information System (INIS)

Broda, E.

1976-01-01

This lecture by Engelbert Broda was written for the 26th Pugwash Conference in Mühlhausen, Germany, 26 – 31 August 1976: Public doubts about nuclear energy are generally directed at the problems of routine emissions of radionuclides, of catastrophic accidents, and of terminal waste disposal. Curiously, the most important problem is not being given sufficient attention: The use of plutonium from civilian reactors fpr weapons production. According to current ideas about a nuclear future, 5000 tons (order of magnitude) of plutonium are to be made annually by year 2000, and about 10 000 tons will all the time be in circulation (transport, reprocessing, reproduction of fuel elements, etc.). It is a misconception that plutonium from power reactors is unsuitable as a nuclear explosive. 5000 tons are enough for several hundred thousand (!) of bombs, Nagasaki type. By the year 2000 maybe 40 – 50 countries will have home-made plutonium. Plutonium production and proliferation are the most serious problems in a nuclear world. (author)

Using Biomolecules to Separate Plutonium

Science.gov (United States)

Gogolski, Jarrod

Used nuclear fuel has traditionally been treated through chemical separations of the radionuclides for recycle or disposal. This research considers a biological approach to such separations based on a series of complex and interdependent interactions that occur naturally in the human body with plutonium. These biological interactions are mediated by the proteins serum transferrin and the transferrin receptor. Transferrin to plutonium in vivo and can deposit plutonium into cells after interacting with the transferrin receptor protein at the cell surface. Using cerium as a non-radioactive surrogate for plutonium, it was found that cerium(IV) required multiple synergistic anions to bind in the N-lobe of the bilobal transferrin protein, creating a conformation of the cerium-loaded protein that would be unable to interact with the transferrin receptor protein to achieve a separation. The behavior of cerium binding to transferrin has contributed to understanding how plutonium(IV)-transferrin interacts in vivo and in biological separations.

Continuous precipitation process of plutonium salts; Procede continu de precipitation des sels de plutonium

Energy Technology Data Exchange (ETDEWEB)

Richard, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-03-01

This work concerns the continuous precipitation process of plutonium oxalate. Investigations about the solubility of different valence states in nitric-oxalic and in nitric-sulfuric-oxalic medium lead to select the precipitation process of tetravalent plutonium oxalate. Settling velocity and granulometry of tetravalent oxalate plutonium have been studied with variation of several precipitation parameters such as: temperature, acidity, excess of oxalic acid and aging time. Then are given test results of some laboratory continuous apparatus. Conditions of operation with adopted tubular apparatus are defined in conclusion. A flow-sheet is given for a process at industrial scale. (author) [French] Cette etude porte sur la precipitation continue de l'oxalate de plutonium. L'etude de la solubilite des differentes valences du plutonium dans des milieux acides nitrique-oxalique, puis nitrique-sulfurique-oxalique conduit a choisir la precipitation de l'oxalate de plutonium tetravalent. L'etude porte ensuite sur la sedimentation et la granulometrie de l'oxalate de Pu{sup 4+} obtenue en faisant varier differents parametres de la precipitation : la temperature, l'acidite, l'exces oxalique et le temps de murissement. La derniere partie traite des resultats obtenus avec plusieurs types d'appareils continus essayes au laboratoire. En conclusion sont donnees les conditions de marche de l'appareil tubulaire adopte, ainsi qu'une extrapolation a l'echelle industrielle sous forme d'un flow-sheet. (auteur)

Plutonium helps probe protein, superconductor

International Nuclear Information System (INIS)

Anon.

1990-01-01

Scientists are finding that plutonium can be a useful research tool that may help them answer important questions in fields as diverse as biochemistry and solid-state physics. This paper reports that U.S. research involving plutonium is confined to the Department of Energy's national laboratories and centers around nuclear weapons technology, waste cleanup and disposal, and health effects. But at Los Alamos National Laboratory, scientists also are using plutonium to probe the biochemical behavior of calmodulin, a key calcium-binding protein that mediates calcium-regulated processes in biological systems. At Argonne National Laboratory, another team is trying to learn how a superconductor's properties are affected by the 5f electrons of an actinide like plutonium

Technological alternatives for plutonium transport

International Nuclear Information System (INIS)

1978-12-01

This paper considers alternative transport modes (air, sea, road, rail) for moving (1) plutonium from a reprocessing plant to a store or a fuel fabrication facility, and (2) MOX fuel from the latter to a reactor. These transport modes and differing forms of plutonium are considered in terms of: their proliferation resistance and safeguards; environmental and safety aspects; and economic aspects. It is tentatively proposed that the transport of plutonium could continue by air or sea where long distances are involved and by road or rail over shorter distances; this would be acceptable from the non-proliferation, environmental impact and economic aspects - there may be advantages in protection if plutonium is transported in the form of mixed oxide

Plutonium

Energy Technology Data Exchange (ETDEWEB)

Miner, William N

1964-01-01

This pamphlet discusses plutonium from discovery to its production, separation, properties, fabrication, handling, and uses, including use as a reactor fuel and use in isotope power generators and neutron sources.

Plutonium Vulnerability Management Plan

International Nuclear Information System (INIS)

1995-03-01

This Plutonium Vulnerability Management Plan describes the Department of Energy's response to the vulnerabilities identified in the Plutonium Working Group Report which are a result of the cessation of nuclear weapons production. The responses contained in this document are only part of an overall, coordinated approach designed to enable the Department to accelerate conversion of all nuclear materials, including plutonium, to forms suitable for safe, interim storage. The overall actions being taken are discussed in detail in the Department's Implementation Plan in response to the Defense Nuclear Facilities Safety Board (DNFSB) Recommendation 94-1. This is included as Attachment B

Preparation of plutonium hexafluoride. Recovery of plutonium from waste dross (1962); Preparation de l'hexafluorure de plutonium. Recuperation du plutonium des scories d'elaboration (1962)

Energy Technology Data Exchange (ETDEWEB)

Gendre, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-01

The object of this work is to study the influence of various physical factors on the rate of fluorination of solid plutonium tetrafluoride by fluorine. In a horizontal oven with a circulation for pure fluorine at atmospheric pressure and 520 deg. C, at a fluorine rate of 9 litres/hour, it is possible to transform 3 g of tetrafluoride to hexafluoride with about 100 per cent transformation and a recovery yield of over 90 per cent, in 4 to 5 hours. The fluorination rate is a function of the temperature, of the fluorine flow-rate, of the crucible surface, of the depth of the tetrafluoride layer and of the reaction time. It does not depend on the diffusion of the fluorine into the solid but is determined by the reaction at the gas-solid interface and obeys the kinetic law (1 - T{sub T}){sup 1/3} = kt + 1. The existence of intermediate fluorides, in particular Pu{sub 4} F{sub 17}, is confirmed by a break in the Arrhenius plot at about 370 deg. C, by differences in the fluorination rates inside the tetrafluoride layer, and by reversible colour changes. The transformation to hexafluoride occurs with a purification with respect of the foreign elements present in the initial plutonium. Recovery of plutonium from waste dross: The study is based on the transformation of occluded plutonium particles to gaseous hexafluoride which is then decomposed thermally to the tetrafluoride which can be reintroduced directly in the production circuit. Under the conditions considered this process is not applicable industrially. After milling, it is possible to separate the dross into enriched (75 per cent Pu in 2.6 per cent by weight of dross) and depleted portions. By prolonged fluorination (16 hours) of the various fractions it is possible to recover about 80 per cent of the plutonium. A treatment plant using fluidization, as described at the end of this study, should make it possible to substantially improve the yield. (author) [French] L'objet de l'etude est l'influence des differents

Surplus plutonium disposition draft environmental impact statement. Summary

International Nuclear Information System (INIS)

1998-07-01

On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel

Modeling of Diffusion of Plutonium in Other Metals and of Gaseous Species in Plutonium-Based Systems

International Nuclear Information System (INIS)

Cooper, Bernard R.; Gayanath W. Fernando; Beiden, S.; Setty, A.; Sevilla, E.H.

2004-01-01

Establish standards for temperature conditions under which plutonium, uranium, or neptunium from nuclear wastes permeates steel, with which it is in contact, by diffusion processes. The primary focus is on plutonium because of the greater difficulties created by the peculiarities of face-centered-cubic-stabilized (delta) plutonium (the form used in the technology generating the waste)

Prospects for the Use of Plutonium in Reactors; Prospective d'Utilisation du Plutonium dans les Reacteurs

Energy Technology Data Exchange (ETDEWEB)

Fossoul, E.; Haubert, P. [BELGONUCLEAIRE (Belgium); Hirschberg, D.; Morlet, E. [International Business Machines of Belgium, Bruxelles (Belgium)

1967-09-15

The introduction, at an increasing rate, of power reactors using slightly enriched uranium will inevitably lead to the production of considerable quantities of plutonium over the next decade. Fast reactors will not be capable of absorbing this material before 1980. The question thus arises of whether one should store the plutonium far future use in fast reactors, recycle it in existing thermal reactors, or try to sell it. The problem has been studied for an electric power generating system that does not foresee selling the plutonium produced by its reactors and does not buy plutonium outside, which enables a good approximation to be made and eliminates the major unknown quantity represented by the future market price of plutonium. Assuming within this system a programme that provides for the construction of power reactors of a given type and capacity at specific dates, the utilization of the plutonium produced can be optimized by linear programming techniques so as to minimize the discounted total cost of the power generated over a given period. A later stage consists in optimizing, by various techniques, not only the utilization but also the production of plutonium by appropriate selection of the power reactor types to be constructed. (author) [French] L'implantation, a un rythme croissant, de centrales nucleaires a uranium legerement enrichi entrainera la production ineluctable d'une quantite importante de plutonium au cours de la prochaine decennie. Les reacteurs a neutrons rapides ne seront capables d'absorber cette production qu'apres 1980. La question se pose donc de savoir s'il est preferable de stocker le plutonium en vue de son utilisation ulterieure dans les reacteurs a neutrons rapides plutot que de le recycler dans les reacteurs actuels a neutrons thermiques ou d'essayer de le vendre. Ce probleme a ete etudie dans le cadre d'un systeme de production d'energie electrique qui ne prevoirait pas la vente du plutonium produit par ses reacteurs nucleaires ni

Radiological safety aspects of handling plutonium

International Nuclear Information System (INIS)

Sundararajan, A.R.

2016-01-01

Department of Atomic Energy in its scheme of harnessing the nuclear energy for electrical power generation and strategic applications has given a huge role to utilization of plutonium. In the power production programme, fast reactors with plutonium as fuel are expected to play a major role. This would require establishing fuel reprocessing plants to handle both thermal and fast reactor fuels. So in the nuclear fuel cycle facilities variety of chemical, metallurgical, mechanical operations have to be carried out involving significant inventories of "2"3"9 Pu and associated radionuclides. Plutonium is the most radiotoxic radionuclide and therefore any facility handling it has to be designed and operated with utmost care. Two problems of major concern in the protection of persons working in plutonium handling facilities are the internal exposure to the operating personnel from uptake of plutonium and transplutonic nuclides as they are highly radiotoxic and the radiation exposure of hands and eye lens during fuel fabrication operations especially while handling recycled high burn up plutonium. In view of the fact that annual limit for intake is very small for "2"3"9Pu and its radiation emission characteristics are such that it is a huge challenge for the health physicists to detect Pu in air and in workers. This paper discusses the principles and practices followed in providing radiological surveillance to workers in plutonium handling areas. The challenges in protecting the workers from receiving exposures to hands and eye lens in handling high burn up plutonium are also discussed. The sites having Pu fuel cycle facilities should have trained medical staff to handle cases involving excessive intake of plutonium. (author)

Accuracy of 99Molybdenum assays in /sup 99m/Technetium solutions

International Nuclear Information System (INIS)

Williams, C.C.; Kereiakes, J.G.; Grossman, L.W.

1981-01-01

A study was performed to determine the accuracy of 99 Mo measurements using three commercial dose calibrators with their 99 Mo assay shields. One 99 Mo assay shield allowed excessive penetration by the lower energy /sup 99m/Tc photons, resulting in the calibrator's falsely high interpretation of the activity of 99 Mo present in the high-activity /sup 99m/Tc eluates. All three calibrators performed adequately with a National Bureau of Standards 99 Mo standard in equilibrium with /sup 99m/Tc. By using low-activity aliquots of 99 Mo and /sup 99m/Tc, a low-level linearity test was performed. Only one of the calibrators was found to reflect accurately the activity of 99 Mo present under all conditions tested

A measurement control program for plutonium isotopic gamma-ray systems at the Rocky Flats Plant

International Nuclear Information System (INIS)

Fleissner, J.G.

1986-01-01

A sound measurement control (MC) program should be an integral part of every nondestructive assay measurement system used for the assay of special nuclear materials. This paper describes a measurement control program for plutonium isotopic composition measurements, using high-resolution gamma-ray spectroscopy, that has been implemented in the Analytical Laboratories and the Chemistry Standards Laboratory at the Rocky Flats Plant. This MC program emphasizes the standardization of data collection procedures along with the implementation of internal and external measurement control checks to provide the requisite measurement quality assurance

Plutonium-induced lymphadenitis in beagles

International Nuclear Information System (INIS)

Dagle, G.E.; Park, J.F.

1976-01-01

Plutonium oxide particles accumulate in the tracheobronchial lymph nodes of beagles exposed by inhalation and in the popliteal lymph nodes after subcutaneous injection in the hind paws. The sequence of histopathologic changes after phagocytosis of particles included necrosis, increased numbers of macrophages, and fibroplasia. Scar tissue eventually replaced the normal architecture of the lymph nodes and sequestered the plutonium particles from surrounding parenchyma. Electron microscopy showed that plutonium particles were aggregated in phagolysosomes of macrophages

Guidelines for international plutonium management: Overview and implications

International Nuclear Information System (INIS)

Bryson, M.C.; Fitzgerald, C.P.; Kincaid, C.

1998-01-01

In September, 1997, nine of the world's plutonium-using countries agreed to a set of guidelines for international plutonium management, with acceptances to be submitted to the International Atomic Energy Agency on December 1. Following three years of discussion, the guidelines provide a unified package of accepted rules for the storage, handling, and transportation of civil plutonium as well as military plutonium that has been declared as no longer required for defense purposes. New requirements include a formal declaration of national plutonium strategies, which will recognize the environmental, economic, and proliferation concerns and the consequent importance of balancing plutonium supply and demand. Nations will also make annual declaration of their non-military stockpiles of unirradiated plutonium, together with estimates of the plutonium content in spent reactor fuel. These guidelines represent the first formally accepted recognition of the need for plutonium management of this scope and could thus provide a partial basis for future monitoring and policy regimes

Six-kilogram-scale electrorefining of plutonium metal

International Nuclear Information System (INIS)

Mullins, L.J.; Morgan, A.N.; Apgar, S.A. III; Christensen, D.C.

1982-09-01

The electrorefining of metallic plutonium scrap to produce high purity metal has been an established procedure at Los Alamos since 1964. This is a batch process and was limited to 4-kg plutonium because of criticality safety considerations. Improvements in critical mass measurements have permitted us to develop a process for 6-kg plutonium. The 6-kg process is now operational. The increased size of the process, together with other improvements which have been made, makes plutonium electrorefining the principal industrial tool for processing and purifying metallic plutonium scrap

Erosional losses of fallout plutonium

International Nuclear Information System (INIS)

Foster, G.R.; Hakonson, T.E.

1987-01-01

Plutonium from fallout after atmospheric explosion of nuclear weapons in the 1950's and 1960s is being redistributed over the landscape by soil erosion and carried on sediment by streams to oceans. Erosion rates computed with the Universal Soil Loss Equation for more than 200,000 sample points on nonfederal land across the US were used to estimate plutonium removal rates by soil erosion. On the average, only about 4% of the eroded sediment reaches the outlet of a major river. The remaining sediment is deposited en route, and because deposition is a selective process, the sediment is enriched in fine particles having the highest concentration of plutonium because of the element's strong association with clay and silt-sized sediment. Estimated enrichment ratios, sediment delivery ratios, and erosion rates were used to estimate annual delivery of fallout plutonium. These estimates ranged from 0.002% of the initial fallout plutonium inventory for the Savannah River basin to 0.01% for the Columbia River basin, to 0.02% for the Hudson and Rio Grande River basins, to 0.08% for the Mississippi River basin. If the deposition of plutonium had been uniformly 1 mCi/km 2 , the estimated plutonium activity on suspended sediment would range from about 7 fCi/g of sediment of the Savannah River basin, to 9 fCi/g for the Mississippi River basin, to 12 fCi/g for the Hudson River basin, to 14 fCi/g for the Columbia and Rio Grande River basins. 45 references, 2 figures, 17 tables

Plutonium story

International Nuclear Information System (INIS)

Seaborg, G.T.

1981-09-01

The first nuclear synthesis and identification (i.e., the discovery) of the synthetic transuranium element plutonium (isotope 238 Pu) and the demonstration of its fissionability with slow neutrons (isotope 239 Pu) took place at the University of California, Berkeley, through the use of the 60-inch and 37-inch cyclotrons, in late 1940 and early 1941. This led to the development of industrial scale methods in secret work centered at the University of Chicago's Metallurgical Laboratory and the application of these methods to industrial scale production, at manufacturing plants in Tennessee and Washington, during the World War II years 1942 to 1945. The chemical properties of plutonium, needed to devise the procedures for its industrial scale production, were studied by tracer and ultramicrochemical methods during this period on an extraordinarily urgent basis. This work, and subsequent investigations on a worldwide basis, have made the properties of plutonium very well known. Its well studied electronic structure and chemical properties give it a very interesting position in the actinide series of inner transition elements

Plutonium research and related activities at the Amarillo National Resource Center for Plutonium

International Nuclear Information System (INIS)

Hartley, R.S.; Beard, C.A.; Barnes, D.L.

1998-01-01

With the end of the Cold War, the US and Russia are reducing their nuclear weapons stockpiles. What to do with the materials from thousands of excess nuclear weapons is an important international challenge. How to handle the remaining US stockpile to ensure safe storage and reliability, in light of the aging support infrastructure, is an important national challenge. To help address these challenges and related issues, the Amarillo National Resource Center for Plutonium is working on behalf of the State of Texas with the US Department of Energy (DOE). The center directs three major programs that address the key aspects of the plutonium management issue: (1) the Communications, Education, Training and Community Involvement Program, which focuses on informing the public about plutonium and providing technical education at all levels; (2) the Environmental, Safety, and Health (ES and H) Program, which investigates the key ES and H impacts of activities related to the DOE weapons complex in Texas; and (3) the Nuclear and Other Materials Program, which is aimed at minimizing safety and proliferation risks by helping to develop and advocate safe stewardship, storage, and disposition of nuclear weapons materials. This paper provides an overview of the center's nuclear activities described in four broad categories of international activities, materials safety, plutonium storage, and plutonium disposition

An Improved Plutonium Trifluoride Precipitation Flowsheet

Energy Technology Data Exchange (ETDEWEB)

Harmon, H.D.

2001-06-26

This report discusses results of the plutonium trifluoride two-stage precipitation study. A series of precipitation experiments was used to identify the significant process variables affecting precipitation performance. A mathematical model of the precipitation process was developed which is based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter which can be used to control the performance of the plutonium trifluoride precipitation process. Recommendations have been made which will optimize the FB-Line plutonium trifluoride precipitation process.

An Improved Plutonium Trifluoride Precipitation Flowsheet

International Nuclear Information System (INIS)

Harmon, H.D.

2001-01-01

This report discusses results of the plutonium trifluoride two-stage precipitation study. A series of precipitation experiments was used to identify the significant process variables affecting precipitation performance. A mathematical model of the precipitation process was developed which is based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter which can be used to control the performance of the plutonium trifluoride precipitation process. Recommendations have been made which will optimize the FB-Line plutonium trifluoride precipitation process

Optically stimulated luminescence sensitivity changes in quartz due to repeated use in single aliquot readout: Experiments and computer simulations

DEFF Research Database (Denmark)

McKeever, S.W.S.; Bøtter-Jensen, L.; Agersnap Larsen, N.

1996-01-01

believed to be occurring. The computer model used includes both shallow and deep ('hard-to-bleach') traps, OSL ('easy-to-bleach') traps, and radiative and non-radiative recombination centres. The model has previously been used successfully to account for sensitivity changes in quartz due to thermal......As part of a study to examine sensitivity changes in single aliquot techniques using optically stimulated luminescence (OSL) a series of experiments has been conducted with single aliquots of natural quartz, and the data compared with the results of computer simulations of the type of processes...... annealing. The simulations are able to reproduce qualitatively the main features of the experimental results including sensitivity changes as a function of reuse, and their dependence upon bleaching time and laboratory dose. The sensitivity changes are believed to be the result of a combination of shallow...

Plutonium valence state distributions

International Nuclear Information System (INIS)

Silver, G.L.

1974-01-01

A calculational method for ascertaining equilibrium valence state distributions of plutonium in acid solutions as a function of the plutonium oxidation number and the solution acidity is illustrated with an example. The method may be more practical for manual use than methods based upon polynomial equations. (T.G.)

PRISM reactor. An option for plutonium disposition?

Energy Technology Data Exchange (ETDEWEB)

Fehlinger, Sebastian; Friess, Friederike; Kuett, Moritz [IANUS, Technische Universitaet Darmstadt (Germany)

2015-07-01

The Power Reactor Innovative Small Module (PRISM) is sodium cooled fast reactor model. The energy output depends on the core configuration, however with an energy output of approximately 300 MWe, the PRISM reactor belongs to the class of small modular reactors. Beside using the reactor as a breeder reactor or for the transmutation of nuclear waste, it might also be used as a burner reactor for separated plutonium. This includes for example U.S.-American excess weapon-grade plutonium as well as separated reactor-grade plutonium. Recently, there has been an ongoing discussion in GB to use the PRISM reactor to dispose their excess civilian plutonium. Depending on the task, the core configuration varies slightly. We will present different layouts and the matching MCNP models, these models can then be used to conduct depletion calculations. From these results, analysis of the change in the plutonium isotopics in the spent fuel, the amount of fissioned plutonium, and the possible annual plutonium throughputs is possible.

The first milligrams of plutonium

International Nuclear Information System (INIS)

Goldschmidt, B.

1996-01-01

This paper relates the discovery of the different plutonium chemical extraction processes in their historical context. The first experiments started during the second world war in 1942 with the American ''Metallurgical Laboratory'' project which brought together Arthur Compton, Enrico Fermi and Glenn Seaborg. During the same period, a competitive English-Canadian project, the ''Montreal Project'', was carried out to test different plutonium solvent extraction techniques. The author participated in both projects and joined the CEA in 1946, where he was in charge of the uranium and plutonium chemistry. By the end of 1949, his team could isolate the first milligrams of French plutonium from uranium oxide pellets of the ZOE reactor. In the beginning of 1952 he developed with his team the PUREX process. (J.S.)

Chloride removal from plutonium alloy

International Nuclear Information System (INIS)

Holcomb, H.P.

1983-01-01

SRP is evaluating a program to recover plutonium from a metallic alloy that will contain chloride salt impurities. Removal of chloride to sufficiently low levels to prevent damaging corrosion to canyon equipment is feasible as a head-end step following dissolution. Silver nitrate and mercurous nitrate were each successfully used in laboratory tests to remove chloride from simulated alloy dissolver solution containing plutonium. Levels less than 10 ppM chloride were achieved in the supernates over the precipitated and centrifuged insoluble salts. Also, less than 0.05% loss of plutonium in the +3, +4, or +6 oxidation states was incurred via precipitate carrying. These results provide impetus for further study and development of a plant-scale process to recover plutonium from metal alloy at SRP

Plutonium production and utilization forecasts in Europe

International Nuclear Information System (INIS)

Haijtink, B.

1976-01-01

The planned accelerated growth of nuclear energy generation in the near future will lead to a large production of plutonium in the thermal reactors. Therefore, up to 1985, the major part of the available plutonium will be plutonium recovered from spent uranium-metal, particularly in the United Kingdom and in France. Because of the low demand for fuelling the fast breeder reactors within the near future, a surplus of fissile plutonium will be accumulated in Europe. Even if the planned availability of the oxide reprocessing capacity will be delayed with two or three years, a plutonium surplus will still exist in Europe, e.g.; in 1985: 25-20 tons. On longer term, up to 2000, the plutonium production in thermal reactors will be sufficient to meet the estimated demand for fast breeder reactors at their commercial introduction foreseen for the nineties. That means that all the plutonium surplus needs not to be stocked for use in fast breeder reactors later on but could be recycled in thermal reactors. The magnitude of the available fissionable materials give an idea of the importance to promote, on an industrial scale, the plutonium recycling technology

Strategies for the plutonium utilization

International Nuclear Information System (INIS)

Zouain, D.M.; Lima, J.O.V.; Sakamoto, L.H.

1981-11-01

A review of the activities involving plutonium (its recycle, utilization and technological status and perspectives) is done. These informations are useful for an economic viability study for the plutonium utilization in thermal reactors (recycling) and in fast breeders reactor (FBR), trying to collect the major number of informations about these subjects. The initial phase describes the present status and projections of plutonium accumulation and requirements. Then, the technological process are described and some strategies are analyzed. (E.G.) [pt

Plutonium titration by controlled potential coulometry; Dosage du plutonium par coulometrie a potentiel impose

Energy Technology Data Exchange (ETDEWEB)

Leguay, N.

2011-07-01

The LAMMAN (Nuclear Materials Metrology Laboratory) is the support laboratory of the CETAMA (Analytical Method Committee), whose two main activities are developing analytic methods, and making and characterizing reference materials. The LAMMAN chose to develop the controlled potential coulometry because it is a very accurate analytical technique which allows the connection between the quantity of element electrolysed to the quantity of electricity measured thanks to the Faraday's law: it does not require the use of a chemical standard. This method was first used for the plutonium titration and was developed in the Materials Analysis and Metrology Laboratory (LAMM), for upgrading its performances and developing it to the titration of other actinides. The equipment and the material used were developed to allow the work in confined atmosphere (in a glove box), with all the restrictions involved. Plutonium standard solutions are used to qualify the method, and in particular to do titrations with an uncertainty better than 0.1 %. The present study allowed making a bibliographic research about controlled potential coulometry applied to the actinides (plutonium, uranium, neptunium, americium and curium). A full procedure was written to set all the steps of plutonium titration, from the preparation of samples to equipments storage. A method validation was done to check the full procedure, and the experimental conditions: working range, uncertainty, performance... Coulometric titration of the plutonium from pure solution (without interfering elements) was developed to the coulometric titration of the plutonium in presence of uranium, which allows to do accurate analyses for the analyses of some parts of the reprocessing of the spent nuclear fuel. The possibility of developing this method to other actinides than plutonium was highlighted thanks to voltammetric studies, like the coulometric titration of uranium with a working carbon electrode in sulphuric medium. (author)

Production of Plutonium Metal from Aqueous Solutions

Energy Technology Data Exchange (ETDEWEB)

Orth, D.A.

2003-01-16

The primary separation of plutonium from irradiated uranium by the Purex solvent extraction process at the Savannah River Plant produces a dilute plutonium solution containing residual fission products and uranium. A cation exchange process is used for concentration and further decontamination of the plutonium, as the first step in the final preparation of metal. This paper discusses the production of plutonium metal from the aqueous solutions.

Automation of plutonium spectrophotometry

International Nuclear Information System (INIS)

Perez, J.J.; Boisde, G.; Goujon de Beauvivier, M.; Chevalier, G.; Isaac, M.

1980-01-01

Instrumentation was designed and constructed for automatic control of plutonium by molecular absorption spectrophotometry, on behalf of the reprocessing facilities, to meet two objectives: on-line measurement, of the valency state of plutonium, on by-pass, with the measured concentration covering the process concentration range up to a few mg.l -1 ; laboratory measurement of plutonium adjusted to valency VI, with operation carried out using a preparative system meeting the required containment specifications. For this two objectives, the photometer, optical cell connections are made by optical fibers resistant to β, γ radiation. Except this characteristic the devices are different according to the quality required for result [fr

Civil plutonium amounts in the world

International Nuclear Information System (INIS)

Naudet, G.

1994-01-01

The experience of plutonium reprocessing in water reactors is positive and today the use of this nuclear fuel is at industrial level. Plutonium quantities in spent fuel go on increasing, plutonium stock coming from reprocessing can be controlled: according to conjuncture, it will evolve by stabilization or decreasing at the beginning of next century

Plutonium isotopic measurements by gamma-ray spectroscopy

International Nuclear Information System (INIS)

Gunnink, R.

1973-11-01

A method is reported for analysis of isotopic and total plutonium by detecting and analyzing gamma rays emitted by the sample. A computerized prototype-system was developed and is now being routinely used at the Savannah River Plant for the nondestructive assay of solution samples. The analyses for 238 Pu, 239 Pu, 240 Pu, 241 Pu, and for 241 Am, when it is present, can be made in counting times as short as 10 to 15 minutes under optimum conditions. Comparison of isotopic ratio values with mass spectrometry generally shows agreement within 0.1 percent for 239 Pu and about 1 percent for 240 Pu and 241 Pu. Some preliminary isotopic measurements on solids are also discussed. (U.S.)

Geomorphology of plutonium in the Northern Rio Grande

Energy Technology Data Exchange (ETDEWEB)

Graf, W.L. [Arizona Univ., Tempe, AZ (United States). Dept., of Geography

1993-03-01

Nearly all of the plutonium in the natural environment of the Northern Rio Grande is associated with soils and sediment, and river processes account for most of the mobility of these materials. A composite regional budget for plutonium based on multi-decadal averages for sediment and plutonium movement shows that 90 percent of the plutonium moving into the system is from atmospheric fallout. The remaining 10 percent is from releases at Los Alamos. Annual variation in plutonium flux and storage exceeds 100 percent. The contribution to the plutonium budget from Los Alamos is associated with relatively coarse sediment which often behaves as bedload in the Rio Grande. Infusion of these materials into the main stream were largest in 1951, 1952, 1957, and 1968. Because of the schedule of delivery of plutonium to Los Alamos for experimentation and weapons manufacturing, the latter two years are probably the most important. Although the Los Alamos contribution to the entire plutonium budget was relatively small, in these four critical years it constituted 71--86 percent of the plutonium in bedload immediately downstream from Otowi.

Geomorphology of plutonium in the Northern Rio Grande

International Nuclear Information System (INIS)

Graf, W.L.

1993-03-01

Nearly all of the plutonium in the natural environment of the Northern Rio Grande is associated with soils and sediment, and river processes account for most of the mobility of these materials. A composite regional budget for plutonium based on multi-decadal averages for sediment and plutonium movement shows that 90 percent of the plutonium moving into the system is from atmospheric fallout. The remaining 10 percent is from releases at Los Alamos. Annual variation in plutonium flux and storage exceeds 100 percent. The contribution to the plutonium budget from Los Alamos is associated with relatively coarse sediment which often behaves as bedload in the Rio Grande. Infusion of these materials into the main stream were largest in 1951, 1952, 1957, and 1968. Because of the schedule of delivery of plutonium to Los Alamos for experimentation and weapons manufacturing, the latter two years are probably the most important. Although the Los Alamos contribution to the entire plutonium budget was relatively small, in these four critical years it constituted 71--86 percent of the plutonium in bedload immediately downstream from Otowi

Method of stripping plutonium from tributyl phosphate solution which contains dibutyl phosphate-plutonium stable complexes

International Nuclear Information System (INIS)

Ochsenfeld, W.; Schmieder, H.

1976-01-01

Fast breeder fuel elements which have been highly burnt-up are reprocessed by extracting uranium and plutonium into an organic solution containing tributyl phosphate. The tributyl phosphate degenerates at least partially into dibutyl phosphate and monobutyl phosphate, which form stable complexes with tetravalent plutonium in the organic solution. This tetravalent plutonium is released from its complexed state and stripped into aqueous phase by contacting the organic solution with an aqueous phase containing tetravalent uranium. 6 claims, 1 drawing figure

Experimental Studies on Plutonium Kinetics in Marine Biota

International Nuclear Information System (INIS)

Fowler, S.; Heyraud, M.; Beasley, T.M.

1976-01-01

Laboratory experiments were undertaken to measure plutonium flux through marine organisms and to clarify the pathways by which this important element is cycled in the marine environment. The use of a specially prepared isotope, plutonium-237, allowed measurements to be made with standard Nal(Tl) scintillation techniques. Mussels, shrimp and worms were allowed to accumulate plutonium-237 from sea water for up to 25 days. Accumulation by shrimp was relatively slow and the degree of uptake was strongly influenced by moulting. Cast moults contained large fractions of the shrimps ' plutonium content, indicating the high affinity of plutonium for surface areas. Only small amounts of the isotope in the moult are lost to water; hence, moulting is considered to be an important biological parameter in the biogeochemical cycling of plutonium. Mussels attained higher concentration factors than shrimp with most of the accumulated isotope (> 80%) located in the shell. Byssus threads often contained large fractions of the mussels' plutonium-237 content and reached concentration factors as high as 4100. Worms readily accumulated plutonium-237 in either the +4 or +6 state, reaching concentration factors of approximately 200, Retention studies indicated a relatively slow loss of plutonium-237 from all animals studied. In the case of mussels, a computed half-time for a large fraction of the animals plutonium content was of the order of 2 years. The more rapid loss from shrimp (Tb 1/2 = 1.5 months) was due principally to the large fraction of plutonium lost at moult. Food chain studies with shrimp indicated that tissue build-up via plutonium ingestion would be a slow process. Total excretion was not entirely a result of passing contaminated food through the gut; approximately 15% of the ingested plutonium was removed from the contaminated food and subsequently excreted by processes other than defaecation of labelled food. Ratios of four different plutonium isotopes used in

Experimental studies on plutonium kinetics in marine biota

International Nuclear Information System (INIS)

Fowler, S.; Heyraud, M.; Beasley, T.M.

1975-01-01

Laboratory experiments were undertaken to measure plutonium flux through marine organisms and to clarify the pathways by which this important element is cycled in the marine environment. The use of a specially prepared isotope, plutonium-237, allowed measurements to be made with standard NaI(Tl) scintillation techniques. Mussels, shrimp and worms were allowed to accumulate plutonium-237 from seawater for up to 25 days. Accumulation by shrimp was relatively slow and the degree of uptake was strongly influenced by moulting. Cast moults contained large fractions of the shrimps' plutonium content, indicating the high affinity of plutonium for surface areas. Only small amounts of the isotope in the moult are lost to water; hence, moulting is considered to be an important biological parameter in the biogeochemical cycling of plutonium. Mussels attained higher concentration factors than shrimp with most of the accumulated isotope (>80%) located in the shell. Byssus threads often contained large fractions of the mussels' plutonium-237 content and reached concentration factors as high as 4100. Worms readily accumulated plutonium-237 in either the +4 or +6 state, reaching concentration factors of approximately 200. Retention studies indicated a relatively slow loss of plutonium-237 from all animals studied. In the case of mussels, a computed half-time for a large fraction of the animals' plutonium content was of the order of 2 years. The more rapid loss from shrimp (Tbsub(1/2)=1.5 months) was due principally to the large fraction of plutonium lost at moult. Food chain studies with shrimp indicated that tissue build-up via plutonium ingestion would be a slow process. Total excretion was not entirely a result of passing contaminated food through the gut; approximately 15% of the ingested plutonium was removed from the contaminated food and subsequently excreted by processes other than defaecation of labelled food. Ratios of four different plutonium isotopes used in the

Radiometric measurements on the fabrication of non-destructive assay standards for WIPP-Performance Demonstration Program

International Nuclear Information System (INIS)

Wong, A.S.; Marshall, R.S.

1997-04-01

The Inorganic Elemental Analysis Group of LANL has prepared several different sets of working reference materials (WRMs). These WRMs are prepared by blending quantities of nuclear materials (plutonium, americium, and enriched uranium) with diatomaceous earth. The blends are encapsulated in stainless steel cylinders. These WRMs are being measured as blind controls in neutron and gamma based non-destructive assay (NDA) instruments. Radiometric measurements on the blending homogeneity and verification on a set of sixty three plutonium based WRMs are discussed in this paper

Controlling variation in the comet assay

Directory of Open Access Journals (Sweden)

Andrew Richard Collins

2014-10-01

Full Text Available Variability of the comet assay is a serious issue, whether it occurs from experiment to experiment in the same laboratory, or between different laboratories analysing identical samples. Do we have to live with high variability, just because the comet assay is a biological assay rather than analytical chemistry? Numerous attempts have been made to limit variability by standardising the assay protocol, and the critical steps in the assay have been identified; agarose concentration, duration of alkaline incubation, and electrophoresis conditions (time, temperature and voltage gradient are particularly important. Even when these are controlled, variation seems to be inevitable. It is helpful to include in experiments reference standards, i.e. cells with a known amount of specific damage to the DNA. They can be aliquots frozen from a single large batch of cells, either untreated (negative controls or treated with, for example, H2O2 or X-rays to induce strand breaks (positive control for the basic assay, or photosensitiser plus light to oxidise guanine (positive control for Fpg- or OGG1-sensitive sites. Reference standards are especially valuable when performing a series of experiments over a long period - for example, analysing samples of white blood cells from a large human biomonitoring trial - to check that the assay is performing consistently, and to identify anomalous results necessitating a repeat experiment. The reference values of tail intensity can also be used to iron out small variations occurring from day to day. We present examples of the use of reference standards in human trials, both within one laboratory and between different laboratories, and describe procedures that can be used to control variation.

Specification analysis of plutonium fuels : a potentiometric method for the determination of plutonium

International Nuclear Information System (INIS)

Vaidyanathan, S.; Natarajan, P.R.

1977-01-01

A potentiometric method for the routine determination of plutonium in the specification analysis of plutonium fuels is described. Plutonium is oxidized to Pu(VI) with AgO and Pu(VI) is reduced with Fe(II) after the destruction of excess AgO with sulphamic acid. The excess Fe(II) is titrated potentiometrically against K 2 Cr 2 O 7 , the titration being carried out by adding a concentrated titrant solution from a weight burette and a suitably diluted solution from another weight burette near the end. The overall relative standard deviation obtained in 326 analyses of a working standard solution by eight experimenters is 0.14 percent. (author)

Electrochemistry of plutonium in molten halides

International Nuclear Information System (INIS)

McCurry, L.E.; Moy, G.M.M.; Bowersox, D.F.

1987-01-01

The electrochemistry of plutonium in molten halides is of technological importance as a method of purification of plutonium. Previous authors have reported that plutonium can be purified by electrorefining impure plutonium in various molten haldies. Work to eluciate the mechanism of the plutonium reduction in molten halides has been limited to a chronopotentiometric study in LiCl-KCl. Potentiometric studies have been carried out to determine the standard reduction potential for the plutonium (III) couple in various molten alkali metal halides. Initial cyclic voltammetric experiments were performed in molten KCL at 1100 K. A silver/silver chloride (10 mole %) in equimolar NaCl-KCl was used as a reference electrode. Working and counter electrodes were tungsten. The cell components and melt were contained in a quartz crucible. Background cyclic voltammograms of the KCl melt at the tungsten electrode showed no evidence of electroactive impurities in the melt. Plutonium was added to the melt as PuCl/sub 3/, which was prepared by chlorination of the oxide. At low concentrations of PuCl/sub 3/ in the melt (0.01-0.03 molar), no reduction wave due to the reduction of Pu(III) was observed in the voltammograms up to the potassium reduction limit of the melt. However on scan reversal after scanning into the potassium reduction limit a new oxidation wave was observed

The Plutonium Temperature Effect Experimental Program

Energy Technology Data Exchange (ETDEWEB)

Haeck, Wim; Leclaire, Nicolas; Letang, Eric [IRSN, Fontenay-aux-Roses (France); Girault, Emmanuel; Fouillaud, Patrick [CEA, VALDUC (France)

2008-07-01

Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect but (up to now) no experimental program has confirmed this effect. The main goal of the French Plutonium Temperature Effect Experimental Program (or PU+ in short) is to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The experiments were conducted in the 'Apparatus B' facility at the CEA Valduc research centre in France and involved several sub-critical approach type of experiments using plutonium nitrate solutions with concentrations of 14.3, 15 and 20 g/l at temperatures ranging from 20 to 40 deg. C. A total number of 14 phase I experiments (consisting of independent subcritical approaches) have been performed (5 at 20 g/l, 4 at 15 g/l and 5 at 14.3 g/l) between 2006 and 2007. The impact of the uncertainties on the solution acidity and the plutonium concentration makes it difficult to clearly demonstrate the positive temperature effect, requiring an additional phase II experiment (in which the use of the same plutonium solution was ensured) from 22 to 28 deg. C performed in July 2007. This experiment has shown the existence of a positive temperature effect approx +2 pcm/deg. C (from 22 to 28 deg. C for a plutonium concentration of 14.3 g/l). (authors)

The distribution of plutonium-241 in rodents

International Nuclear Information System (INIS)

Priest, N.D.

1977-01-01

Plutonium-241 citrate solution at pH 6.5 was injected intravenously or intraperitoneally into hamsters and rats at a dose of 50 MBq kg -1 (1.35 mCi kg -1 ). The animals were killed 1 day or 1 week later, and tissues were removed for autoradiography and radiochemical analysis. Plutonium-241 was distributed in rats in the same way as plutonium-239, and is a suitable isotope for high-resolution tissue-section autoradiography. Plutonium deposits in cells consisted of a nuclear and a cytoplasmic component. In the hamster kidney cells, the amount associated with the nucleus was about 55 per cent of the total cellular plutonium at 24 hours after injection. Six days later, it was only about 30 per cent. Plutonium deposits were also characterized in hepatocytes, in the interstitial cells of the testes, in the cells of ovarian follicles, in chondrocytes and in bone cells, including osteoblasts and osteocytes. In bone there appeared to be both an extracellular and intracellular deposit. No evidence was found of substantial incorporation of plutonium into the mineral phase of bone. (author)

Plutonium Speciation, Solubilization and Migration in Soils

International Nuclear Information System (INIS)

Neu, M.; Runde, W.

1999-01-01

This report summarizes research completed in the first half of a three-year project. As outlined in the authors' proposal they are focusing on (1) characterizing the plutonium at an actinide contaminated site, RFETS, including determining the origin, dispersion, and speciation of the plutonium, (2) studying environmentally important plutonium complexes, primarily hydroxides and carbonates, and (3) examining the interactions of plutonium species with manganese minerals. In the first year the authors focused on site based studies. This year they continue to characterize samples from the RFETS, study the formation and structural and spectroscopic features of environmentally relevant Pu species, and begin modeling the environmental behavior of plutonium

Performance Values for Non-Destructive Assay (NDA) Technique Applied to Wastes: Evaluation by the ESARDA NDA Working Group

International Nuclear Information System (INIS)

Rackham, Jamie; Weber, Anne-Laure; Chard, Patrick

2012-01-01

The first evaluation of NDA performance values was undertaken by the ESARDA Working Group for Standards and Non Destructive Assay Techniques and was published in 1993. Almost ten years later in 2002 the Working Group reviewed those values and reported on improvements in performance values and new measurement techniques that had emerged since the original assessment. The 2002 evaluation of NDA performance values did not include waste measurements (although these had been incorporated into the 1993 exercise), because although the same measurement techniques are generally applied, the performance is significantly different compared to the assay of conventional Safeguarded special nuclear material. It was therefore considered more appropriate to perform a separate evaluation of performance values for waste assay. Waste assay is becoming increasingly important within the Safeguards community, particularly since the implementation of the Additional Protocol, which calls for declaration of plutonium and HEU bearing waste in addition to information on existing declared material or facilities. Improvements in the measurement performance in recent years, in particular the accuracy, mean that special nuclear materials can now be accounted for in wastes with greater certainty. This paper presents an evaluation of performance values for the NDA techniques in common usage for the assay of waste containing special nuclear material. The main topics covered by the document are: 1- Techniques for plutonium bearing solid wastes 2- Techniques for uranium bearing solid wastes 3 - Techniques for assay of fissile material in spent fuel wastes. Originally it was intended to include performance values for measurements of uranium and plutonium in liquid wastes; however, as no performance data for liquid waste measurements was obtained it was decided to exclude liquid wastes from this report. This issue of the performance values for waste assay has been evaluated and discussed by the ESARDA

Performance Values for Non-Destructive Assay (NDA) Technique Applied to Wastes: Evaluation by the ESARDA NDA Working Group

Energy Technology Data Exchange (ETDEWEB)

Rackham, Jamie [Babcock International Group, Sellafield, Seascale, Cumbria, (United Kingdom); Weber, Anne-Laure [Institut de Radioprotection et de Surete Nucleaire Fontenay-Aux-Roses (France); Chard, Patrick [Canberra, Forss Business and Technology park, Thurso, Caithness (United Kingdom)

2012-12-15

The first evaluation of NDA performance values was undertaken by the ESARDA Working Group for Standards and Non Destructive Assay Techniques and was published in 1993. Almost ten years later in 2002 the Working Group reviewed those values and reported on improvements in performance values and new measurement techniques that had emerged since the original assessment. The 2002 evaluation of NDA performance values did not include waste measurements (although these had been incorporated into the 1993 exercise), because although the same measurement techniques are generally applied, the performance is significantly different compared to the assay of conventional Safeguarded special nuclear material. It was therefore considered more appropriate to perform a separate evaluation of performance values for waste assay. Waste assay is becoming increasingly important within the Safeguards community, particularly since the implementation of the Additional Protocol, which calls for declaration of plutonium and HEU bearing waste in addition to information on existing declared material or facilities. Improvements in the measurement performance in recent years, in particular the accuracy, mean that special nuclear materials can now be accounted for in wastes with greater certainty. This paper presents an evaluation of performance values for the NDA techniques in common usage for the assay of waste containing special nuclear material. The main topics covered by the document are: 1- Techniques for plutonium bearing solid wastes 2- Techniques for uranium bearing solid wastes 3 - Techniques for assay of fissile material in spent fuel wastes. Originally it was intended to include performance values for measurements of uranium and plutonium in liquid wastes; however, as no performance data for liquid waste measurements was obtained it was decided to exclude liquid wastes from this report. This issue of the performance values for waste assay has been evaluated and discussed by the ESARDA

Recent trends of plutonium facilities and their control

Energy Technology Data Exchange (ETDEWEB)

Muto, T [Power Reactor and Nuclear Fuel Development Corp., Tokai, Ibaraki (Japan). Tokai Works

1974-02-01

Much interest has been focussed on Pu recycle since the oil crisis because of an expected shortage of enriched uranium. Plutonium handling techniques and plutonium fuel fabricating facilities should be developed to meet the future demand of plutonium, but the radioactive property of plutonium to be reprocessed from spent fuel and recycled plutonium is remarkably different, and it has to be handled safely. Technical criteria for plutonium facilities are specified in the USAEC regulatory guides and other rules. Some of these criteria are location condition, quality of confinement, protection against accidents and so on. The control conditions for plutonium facilities are exposure control, criticality control, measurement control and new system of safeguard. These problems are under development to meet the future requirement for the safe handling of Pu material.

Plutonium Oxide Process Capability Work Plan

Energy Technology Data Exchange (ETDEWEB)

Meier, David E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tingey, Joel M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-02-28

Pacific Northwest National Laboratory (PNNL) has been tasked to develop a Pilot-scale Plutonium-oxide Processing Unit (P3U) providing a flexible capability to produce 200g (Pu basis) samples of plutonium oxide using different chemical processes for use in identifying and validating nuclear forensics signatures associated with plutonium production. Materials produced can also be used as exercise and reference materials.

Optically stimulated luminescence sensitivity changes in quartz due to repeated use in single aliquot readout: experiments and computer simulations

International Nuclear Information System (INIS)

McKeever, S.W.S.; Oklahoma State Univ., Stillwater, OK; Boetter-Jensen, L.; Agersnap Larsen, N.; Mejdahl, V.; Poolton, N.R.J.

1996-01-01

As part of a study to examine sensitivity changes in single aliquot techniques using optically stimulated luminescence (OSL) a series of experiments has been conducted with single aliquots of natural quartz, and the data compared with the results of computer simulations of the type of processes believed to be occurring. The computer model used includes both shallow and deep ('hard-to-bleach') traps, OSL ('easy-to-bleach') traps, and radiative and non-radiative recombination centres. The model has previously been used successfully to account for sensitivity changes in quartz due to thermal annealing. The simulations are able to reproduce qualitatively the main features of the experimental results including sensitivity changes as a function of re-use, and their dependence upon bleaching time and laboratory dose. The sensitivity changes are believed to be the result of a combination of shallow trap and deep trap effects. (author)

Weapons-grade plutonium dispositioning. Volume 1: Executive summary

International Nuclear Information System (INIS)

Parks, D.L.; Sauerbrun, T.J.

1993-06-01

The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate dispositioning options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) assisted NAS in this evaluation by investigating the technical aspects of the dispositioning options and their capability for achieving plutonium annihilation levels greater than 90%. Additionally, the INEL investigated the feasibility of using plutonium fuels (without uranium) for disposal in existing light water reactors and provided a preconceptual analysis for a reactor specifically designed for destruction of weapons-grade plutonium. This four-volume report was prepared for NAS to document the findings of these studies. Volume 2 evaluates 12 plutonium dispositioning options. Volume 3 considers a concept for a low-temperature, low-pressure, low-power-density, low-coolant-flow-rate light water reactor that quickly destroys plutonium without using uranium or thorium. This reactor concept does not produce electricity and has no other mission than the destruction of plutonium. Volume 4 addresses neutronic performance, fabrication technology, and fuel performance and compatibility issues for zirconium-plutonium oxide fuels and aluminum-plutonium metallic fuels. This volumes gives summaries of Volumes 2--4

A novel double-isotope technique for the enzymatic assay of plasma histamine: application to estimation of mast cell activation assessed by antigen challenge in asthmatics

International Nuclear Information System (INIS)

Brown, M.J.; Ind, P.W.; Causon, R.; Lee, T.H.

1982-01-01

The concentration of plasma histamine may provide an index of mast cell activation (degranulation) and can be measured by a sensitive radioenzymatic assay based on its specific conversion to (/sup 3/H)-methylhistamine in the presence of histamine-N-methyltransferase and (/sup 3/H)-S-adenosyl-L-methionine. In this assay, the separation of excess (/sup 3/H)-S-adenosyl-L-methionine from (/sup 3/H)-methylhistamine requires several steps, for which a correction factors is necessary to maintain precision. In the present modification, duplicate 50-microliters aliquots of each plasma sample were incubated with histamine-N-methyltransferase and (/sup 3/H)-S-adenosyl-L-methionine. A further aliquot, with an added standard of 200 ng/ml histamine, was incubated with histamine-N-methyl-transferase and (/sup 14/C)-S-adenosyl-L-methionine. This standard was converted to (/sup 14/C)-methylhistamine, and its recovery at the end of the assay corrected both for varying efficiency of methylation among plasma samples and for losses during the subsequent extraction and separation stages. The sensitivity of the assay was 25 pg/ml. The intra-assay and interassay coefficients of variation were 7.2% and 11.6%, respectively. In five asthmatics, antigen challenge caused a 28% fall in FEV1, and this was associated with a twofold to threefold rise in plasma histamine concentration. This assay may thus prove a useful method for assessing the role of mast cell release of mediators in vivo

Long time contamination from plutonium

International Nuclear Information System (INIS)

Fueloep, M.; Patzeltova, N.; Ragan, P.; Matel, L.

1995-01-01

Plutonium isotopes in the organism of the patient (who had participated in the liquidation works after the Chernobyl accident; for three month he had stayed in the epicenter, where he acted as a chauffeur driving a radioactive material to the place of destination) from urine were determined. For determination of the concentration of Pu-239, Pu-240 in urine a modified radiochemical method was used. After mineralization the sample was separated as an anion-nitrate complex with contact by the anion form of the resin in the column. The resin was washed by 8 M HNO 3 , the 8 M HCl with 0.3 M HNO 3 for removing the other radionuclides. The solution 0.36 M HCl with 0.01 M HF was used for the elution of plutonium. Using the lanthanum fluoride technique the sample was filtrated through a membrane filter. The plutonium was detected in the dry sample. The Pu-239 tracer was used for the evaluation of the plutonium separation efficiency. The alpha spectrometric measurements were carried out with a large area silicon detector. The samples were measured and evaluated in the energy region 4.98-5.18 MeV. The detection limit of alpha spectrometry measurements has been 0.01 Bq dm -3 . The concentration of plutonium in the 24-hour urine was determined three times in the quarter year intervals. The results are: 54 mBq, 63.2 mBq, 53 mBq, with average 56,7 mBq. From the results of the analyses of plutonium depositions calculated according to ICRP 54 the intake of this radionuclide for the patient was 56.7 kBq. To estimate a committed effective dose (50 years) from the intake of plutonium was used a conversion factor 6.8.10 -5 Sv.Bq -1 (class W). So the expressed committed effective dose received from the plutonium intake is 3.8 Sv. This number is relatively high and all the effective dose will be higher, because the patient was exposed to the other radionuclides too. For example the determination of the rate radionuclides Am-241/Pu-239,Pu-240 was 32-36 % in the fallout after the Chernobyl

Plutonium gastrointestinal absorption by adults baboons

International Nuclear Information System (INIS)

Lataillade, G.; Madic, C.; Willemot, J.M.; Germain, P.; Colle, C.; Metivier, H.

1991-01-01

Gastrointestinal absorption of plutonium was investigated in baboons after ingestion of plutonium solution (oxidation states III; IV; V; VI), and plutonium incorporated in soya bean and winkles. We studied the effects of oxidation state and ingested mass for masses ranging from 0.35 μg to 51.6 x 10 +3 μg (4 x 10 -2 to 7776 μg of plutonium per kg of body weight). No clear increase in plutonium retention was shown for concentrations of plutonium smaller than 1 μg/kg. From 1 μg/kg to 1 mg/kg no effects of mass or oxidation state was observed and the mean fractional retention value was 10 -4 . For ingested masses higher than 1 mg/kg the fractional retention values respectively increased for Pu(V) and Pu(III) to (0.9 + 0.2) x 10 -2 and (7.4 + 4.1) x 10 -4 of the ingested mass. This increase might be due to the weak hydrolysis of these oxidation states which would increase gastrointestinal absorption by decrease of hydroxide formation. The fraction of plutonium retained after ingestion of soya bean was (3.0 + 0.5) x 10 -4 about 3 fold higher than the value for 238 Pu nitrate solution. No clear increase in plutonium retention was shown after ingestion of winkles containing 238 Pu. In conclusion, except for high masses of ingested Pu, the retention of which could reach 1% of the ingested dose, our results show that the gastrointestinal transfer factor of 10 -4 proposed by ICRP for gastrointestinal absorption of soluble form of Pu is acceptable, but 10 -3 would provide better safety margin [fr

Disposing of the world's excess plutonium

International Nuclear Information System (INIS)

McCormick, J.M.; Bullen, D.B.

1998-01-01

The authors undertake three key objectives in addressing the issue of plutonium disposition at the end of the Cold War. First, the authors estimate the total global inventory of plutonium both from weapons dismantlement and civil nuclear power reactors. Second, they review past and current policy toward handling this metal by the US, Russia, and other key countries. Third, they evaluate the feasibility of several options (but especially the vitrification and mixed oxide fuel options announced by the Clinton administration) for disposing of the increasing amounts of plutonium available today. To undertake this analysis, the authors consider both the political and scientific problems confronting policymakers in dealing with this global plutonium issue. Interview data with political and technical officials in Washington and at the International Atomic Energy Agency in Vienna, Austria, and empirical inventory data on plutonium from a variety of sources form the basis of their analysis

Selecting a plutonium vitrification process

Energy Technology Data Exchange (ETDEWEB)

Jouan, A. [Centre d`Etudes de la Vallee du Rhone, Bagnols sur Ceze (France)

1996-05-01

Vitrification of plutonium is one means of mitigating its potential danger. This option is technically feasible, even if it is not the solution advocated in France. Two situations are possible, depending on whether or not the glass matrix also contains fission products; concentrations of up to 15% should be achievable for plutonium alone, whereas the upper limit is 3% in the presence of fission products. The French continuous vitrification process appears to be particularly suitable for plutonium vitrification: its capacity is compatible with the required throughout, and the compact dimensions of the process equipment prevent a criticality hazard. Preprocessing of plutonium metal, to convert it to PuO{sub 2} or to a nitric acid solution, may prove advantageous or even necessary depending on whether a dry or wet process is adopted. The process may involve a single step (vitrification of Pu or PuO{sub 2} mixed with glass frit) or may include a prior calcination step - notably if the plutonium is to be incorporated into a fission product glass. It is important to weigh the advantages and drawbacks of all the possible options in terms of feasibility, safety and cost-effectiveness.

Plutonium Disposition Now exclamation point

International Nuclear Information System (INIS)

Buckner, M.R.

1995-01-01

A means for use of existing processing facilities and reactors for plutonium disposition is described which requires a minimum capital investment and allows rapid implementation. The scenario includes interim storage and processing under IAEA control, and fabrication into MOX fuel in existing or planned facilities in Europe for use in operating reactors in the two home countries. Conceptual studies indicate that existing Westinghouse four-loop designs can safety dispose of 0.94 MT of plutonium per calendar year. Thus, it would be possible to consume the expected US excess stockpile of about 50 MT in two to three units of this type, and it is highly likely that a comparable amount of the FSU excess plutonium could be deposed of in a few VVER-1000's. The only major capital project for this mode of plutonium disposition would be the weapons-grade plutonium processing which could be done in a dedicated international facility or using existing facilities in the US and FSU under IAEA control. This option offers the potential for quick implementation at a very low cost to the governments of the two countries

Plutonium in depleted uranium penetrators

International Nuclear Information System (INIS)

McLaughlin, J.P.; Leon-Vintro, L.; Smith, K.; Mitchell, P.I.; Zunic, Z.S.

2002-01-01

Depleted Uranium (DU) penetrators used in the recent Balkan conflicts have been found to be contaminated with trace amounts of transuranic materials such as plutonium. This contamination is usually a consequence of DU fabrication being carried out in facilities also using uranium recycled from spent military and civilian nuclear reactor fuel. Specific activities of 239+240 Plutonium generally in the range 1 to 12 Bq/kg have been found to be present in DU penetrators recovered from the attack sites of the 1999 NATO bombardment of Kosovo. A DU penetrator recovered from a May 1999 attack site at Bratoselce in southern Serbia and analysed by University College Dublin was found to contain 43.7 +/- 1.9 Bq/kg of 239+240 Plutonium. This analysis is described. An account is also given of the general population radiation dose implications arising from both the DU itself and from the presence of plutonium in the penetrators. According to current dosimetric models, in all scenarios considered likely ,the dose from the plutonium is estimated to be much smaller than that due to the uranium isotopes present in the penetrators. (author)

Decontaminaion of metals containing plutonium and americium

International Nuclear Information System (INIS)

Seitz, M.G.; Gerding, T.J.; Steindler, M.J.

1979-06-01

Melt-slagging (melt-refining) techniques were evaluated as a decontamination and consolidation step for metals contaminated with oxides of plutonium and americium. Experiments were performed in which mild steel, stainless steel, and nickel contaminated with oxides of plutonium and americium were melted in the presence of silicate slags of various compositions. The metal products were low in contamination, with the plutonium and americium strongly fractionated to the slags. Partition coefficients (plutonium in slag/plutonium in steel) of 7 x 10 6 were measured with boro-silicate slag and of 3 x 10 6 with calcium, magnesium silicate slag. Decontamination of metals containing as much as 14,000 ppM plutonium appears to be as efficient as for metals with plutonium levels of 400 ppM. Staged extraction, that is, a remelting of processed metal with clean slag, results in further decontamination of the metal. The second extraction is effective with either resistance-furnace melting or electric-arc melting. Slag adhering to the metal ingots and in defects within the ingots is in the important contributors to plutonium retained in processed metals. If these sources of plutonium are controlled, the melt-refining process can be used on a large scale to convert highly contaminated metals to homogeneous and compact forms with very low concentrations of plutonium and americium. A conceptual design of a melt-refining process to decontaminate plutonium- and americium-contaminated metals is described. The process includes single-stage refining of contaminated metals to produce a metal product which would have less than 10 nCi/g of TRU-element contamination. Two plant sizes were considered. The smaller conceptual plant processes 77 kg of metal per 8-h period and may be portable.The larger one processes 140 kg of metal per 8-h period, is stationary, and may be near te maximum size that is practical for a metal decontamination process

Light water breeder reactor using a uranium-plutonium cycle

International Nuclear Information System (INIS)

Radkowsky, A.; Chen, R.

1990-01-01

This patent describes a light water receptor (LWR) for breeding fissile material using a uranium-plutonium cycle. It comprises: a prebreeder section having plutonium fuel containing a Pu-241 component, the prebreeder section being operable to produce enriched plutonium having an increased Pu-241 component; and a breeder section for receiving the enriched plutonium from the prebreeder section, the breeder section being operable for breeding fissile material from the enriched plutonium fuel. This patent describes a method of operating a light water nuclear reactor (LWR) for breeding fissile material using a uranium-plutonium cycle. It comprises: operating the prebreeder to produce enriched plutonium fuel having an increased Pu-241 component; fueling a breeder section with the enriched plutonium fuel to breed the fissile material

The determination of plutonium isotopes in environmental samples

International Nuclear Information System (INIS)

Siripirom, Lopchai.

1983-01-01

The concentration of plutonium in environmental samples such as soil, water, and surface air in the middle part of Thailand were studied. The surface air were collected only at the fifth floor of the Office of Atomic Energy for Peace (OAEP). Plutonium-242 was used as a tracer. Soil and air samples were dissolved by pyrosulphate fusion, and plutonium was co-precipitated with barium sulfate. Then dissolved the precipitate in perchloric acid. Plutonium was extracted out by using solvent bis-(2-ethylhexyl) phosphoric acid (HDEHP). Plutonium in water samples were coprecipitated with iron (III) hydroxide and were dissolved in 8 M. nitric acid. Then the plutonium was separated out by using anion exchange resin, Dowex 1x4. After the solvent extraction or the anion exchange, plutonium was coprecipitated with cerous hydroxide. The activities of plutonium were measured by a surface barrier detector for about 24 hours. Lower limit of detection for 1,440 minutes is 0.012 pCi. These studies showed that only plutonium-239, 240 was observed. The range of activities of plutonium-239, 240 in soil were 0.002-0.157 pCi/g (dry), in water were 0.1-81 f Ci/l, and in air were 7-330 a Ci/m 3 . However, the plutonium concentrations in these studies are far below the maximum permissible concentration (MPC) recommended by International Commission on Radiological Protection (ICRP) for general population which is equal to 3x10 8 f Ci/l of water and 5x10 6 a Ci/m 3 of air

Plutonium contaminated materials research programme

International Nuclear Information System (INIS)

Higson, S.G.

1986-01-01

The paper is a progress report for 1985 from the Plutonium Contaminated Materials Working Party (PCMWP). The PCMWP co-ordinates research and development on a national basis in the areas of management, treatment and immobilisation of plutonium contaminated materials, for the purpose of waste management. The progress report contains a review of the development work carried out in eight areas, including: reduction of arisings, plutonium measurement, sorting and packaging, washing of shredded combustible PCM, decommissioning and non-combustible PCM treatment, PCM immobilisation, treatment of alpha bearing liquid wastes, and engineering objectives. (UK)

Nuclear legacy. Democracy in a plutonium economy

International Nuclear Information System (INIS)

Barnaby, F.

1997-01-01

There have already been a few hundred known incidents of nuclear smuggling, mostly of small quantities not close to weapons grade material - but one gram of plutonium is more than sufficient to cause significant harm and to pose a substantial threat. The potential for further thefts is growing as the world produces ever more quantities of plutonium, not only from the dismantling of nuclear weapons but also from the separation out of plutonium from spent uranium nuclear reactor fuel elements. Trying to prevent the theft of gram quantities of plutonium would require levels of protection and surveillance unacceptably high in a democratic society. It is unlikely, therefore, that democracy could survive in a plutonium economy

Diffusion in the uranium - plutonium system and self-diffusion of plutonium in epsilon phase

International Nuclear Information System (INIS)

Dupuy, M.

1967-07-01

A survey of uranium-plutonium phase diagram leads to confirm anglo-saxon results about the plutonium solubility in α uranium (15 per cent at 565 C) and the uranium one in ζ phase (74 per cent at 565 C). Interdiffusion coefficients, for concentration lower than 15 per cent had been determined in a temperature range from 410 C to 640 C. They vary between 0.2 and 6 10 12 cm 2 s -1 , and the activation energy between 13 and 20 kcal/mole. Grain boundary, diffusion of plutonium in a uranium had been pointed out by micrography, X-ray microanalysis and α autoradiography. Self-diffusion of plutonium in ε phase (bcc) obeys Arrhenius law: D = 2. 10 -2 exp -(18500)/RT. But this activation energy does not follow empirical laws generally accepted for other metals. It has analogies with 'anomalous' bcc metals (βZr, βTi, βHf, U γ ). (author) [fr

Quantification of circulating mature endothelial cells using a whole blood four-color flow cytometric assay.

Science.gov (United States)

Jacques, Nathalie; Vimond, Nadege; Conforti, Rosa; Griscelli, Franck; Lecluse, Yann; Laplanche, Agnes; Malka, David; Vielh, Philippe; Farace, Françoise

2008-09-15

Circulating endothelial cells (CEC) are currently proposed as a potential biomarker for measuring the impact of anti-angiogenic treatments in cancer. However, the lack of consensus on the appropriate method of CEC measurement has led to conflicting data in cancer patients. A validated assay adapted for evaluating the clinical utility of CEC in large cohorts of patients undergoing anti-angiogenic treatments is needed. We developed a four-color flow cytometric assay to measure CEC as CD31(+), CD146(+), CD45(-), 7-amino-actinomycin-D (7AAD)(-) events in whole blood. The distinctive features of the assay are: (1) staining of 1 ml whole blood, (2) use of a whole blood IgPE control to measure accurately background noise, (3) accumulation of a large number of events (almost 5 10(6)) to ensure statistical analysis, and (4) use of 10 microm fluorescent microbeads to evaluate the event size. Assay reproducibility was determined in duplicate aliquots of samples drawn from 20 metastatic cancer patients. Assay linearity was tested by spiking whole blood with low numbers of HUVEC. Five-color flow cytometric experiments with CD144 were performed to confirm the endothelial origin of the cells. CEC were measured in 20 healthy individuals and 125 patients with metastatic cancer. Reproducibility was good between duplicate aliquots (r(2)=0.948, mean difference between duplicates of 0.86 CEC/ml). Detected HUVEC correlated with spiked HUVEC (r(2)=0.916, mean recovery of 100.3%). Co-staining of CD31, CD146 and CD144 confirmed the endothelial nature of cells identified as CEC. Median CEC levels were 6.5/ml (range, 0-15) in healthy individuals and 15.0/ml (range, 0-179) in patients with metastatic carcinoma (p<0.001). The assay proposed here allows reproducible and sensitive measurement of CEC by flow cytometry and could help evaluate CEC as biomarkers of anti-angiogenic therapies in large cohorts of patients.

Atomic energy policy of Japan, especially plutonium utilization policy

International Nuclear Information System (INIS)

Moriguchi, Y.

1993-01-01

The necessity of plutonium use in Japan is discussed. Basic policy regarding plutonium use and future plutonium utilization programme is described including such an aspect as management of plutonium from dismantled nuclear weapons

Solubility of plutonium dioxide aerosols, in vitro

International Nuclear Information System (INIS)

Newton, G.J.; Kanapilly, G.M.

1976-01-01

Solubility of plutonium aerosols is an important parameter in establishing risk estimates for industrial workers who might accidentally inhale these materials and in evaluating environmental health impacts associated with Pu. In vitro solubility of industrial plutonium aerosols in a simulated lung fluid is compared to similar studies with ultrafine aerosols from laser ignition of delta phase plutonium metal and laboratory-produced spherical particles of 238 PuO 2 and 239 PuO 2 . Although relatively insoluble, industrial plutonium-mixed oxide aerosols were much more soluble than laboratory-produced plutonium dioxide particles. Chain agglomerate aerosols from laser ignition of metallic Pu indicated in vitro dissolution half-times of 10 and 50 days for activity median aerodynamic diameter (AMAD) of 0.7 and 2.3 μm, respectively. Plutonium-containing mixed oxide aerosols indicated dissolution half-times of 40 to 500 days for particles formed by industrial powder comminution and blending. Centerless grinding of fuel pellets yielded plutonium-containing aerosols with dissolution half-times of 1200 to 8000 days. All mixed oxide particles were in the size range 1.0 μm to 2.5 μm AMAD

Ultra-small plutonium oxide nanocrystals: an innovative material in plutonium science.

Science.gov (United States)

Hudry, Damien; Apostolidis, Christos; Walter, Olaf; Janssen, Arne; Manara, Dario; Griveau, Jean-Christophe; Colineau, Eric; Vitova, Tonya; Prüssmann, Tim; Wang, Di; Kübel, Christian; Meyer, Daniel

2014-08-11

Apart from its technological importance, plutonium (Pu) is also one of the most intriguing elements because of its non-conventional physical properties and fascinating chemistry. Those fundamental aspects are particularly interesting when dealing with the challenging study of plutonium-based nanomaterials. Here we show that ultra-small (3.2±0.9 nm) and highly crystalline plutonium oxide (PuO2 ) nanocrystals (NCs) can be synthesized by the thermal decomposition of plutonyl nitrate ([PuO2 (NO3 )2 ]⋅3 H2 O) in a highly coordinating organic medium. This is the first example reporting on the preparation of significant quantities (several tens of milligrams) of PuO2 NCs, in a controllable and reproducible manner. The structure and magnetic properties of PuO2 NCs have been characterized by a wide variety of techniques (powder X-ray diffraction (PXRD), X-ray absorption fine structure (XAFS), X-ray absorption near edge structure (XANES), TEM, IR, Raman, UV/Vis spectroscopies, and superconducting quantum interference device (SQUID) magnetometry). The current PuO2 NCs constitute an innovative material for the study of challenging problems as diverse as the transport behavior of plutonium in the environment or size and shape effects on the physics of transuranium elements. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Current status of the plutonium hot particle problem

International Nuclear Information System (INIS)

Richmond, C.R.

1975-01-01

Information now available on the question of lung irradiation from particulate plutonium is reviewed. Careful consideration of the available data shows that particulate plutonium is not more hazardous than the same amount of plutonium distributed uniformly. The data also suggest that the potential hazard from plutonium increases as the dispersion throughout the lung becomes more uniform

Appraisal of BWR plutonium burners for energy centers

International Nuclear Information System (INIS)

Williamson, H.E.

1976-01-01

The design of BWR cores with plutonium loadings beyond the self-generation recycle (SGR) level is investigated with regard to their possible role as plutonium burners in a nuclear energy center. Alternative plutonium burner approaches are also examined including the substitution of thorium for uranium as fertile material in the BWR and the use of a high-temperature gas reactor (HTGR) as a plutonium burner. Effects on core design, fuel cycle facility requirements, economics, and actinide residues are considered. Differences in net fissile material consumption among the various plutonium-burning systems examined were small in comparison to uncertainties in HTGR, thorium cycle, and high plutonium-loaded LWR technology. Variation in the actinide content of high-level wastes is not likely to be a significant factor in determining the feasibility of alternate systems of plutonium utilization. It was found that after 10,000 years the toxicity of actinide high-level wastes from the plutonium-burning fuel cycles was less than would have existed if the processed natural ores had not been used for nuclear fuel. The implications of plutonium burning and possible future fuel cycle options on uranium resource conservation are examined in the framework of current ERDA estimates of minable uranium resources

Search for plutonium salt deposits in the plutonium extraction batteries of the Marcoule plant (1963)

International Nuclear Information System (INIS)

Bouzigues, H.; Reneaud, J.M.

1963-01-01

This report describes a method and a special apparatus making it possible to detach the insoluble plutonium salt deposits in the extraction chain of an irradiated fuel treatment plant. The process chosen allows the detection, in the extraction batteries or in the highly active chemical engineering equipment, of plutonium quantities of a few grains. After four years operation it has been impossible to detect measurable quantities of plutonium in any part of the extraction chain. The results have been confirmed by visual examinations carried out with a specially constructed endoscope. (authors) [fr

Tabulated Neutron Emission Rates for Plutonium Oxide

Energy Technology Data Exchange (ETDEWEB)

Shores, Erik Frederick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-07-24

This work tabulates neutron emission rates for 80 plutonium oxide samples as reported in the literature. Plutonium-­238 and plutonium-­239 oxides are included and such emission rates are useful for scaling tallies from Monte Carlo simulations and estimating dose rates for health physics applications.

Model of plutonium dynamics in a deciduous forest ecosystem

International Nuclear Information System (INIS)

Garten, C.T. Jr.; Gardner, R.H.; Dahlman, R.C.

1980-01-01

A linear compartment model with donor-controlled flows between compartments was designed to describe and simulate the behavior of plutonium ( 239 240 Pu) in a contaminated forest ecosystem at Oak Ridge, TN. At steady states predicted by the model, less than 0.25% of the plutonium in the ecosystem resides in biota. Soil is the major repository of plutonium in the forest, and exchanges of plutonium between soil and litter or soil and tree roots were dominant transfers affecting the ecosystem distribution of plutonium. Variation in predicted steady-state amounts of plutonium in the forest, given variability in the model parameters, indicates that our ability to develop models of plutonium transport in ecosystems should improve with greater precision in data from natural environments and a better understanding of sources of variation in plutonium data

Plutonium metal exchange program : current status and statistical analysis

Energy Technology Data Exchange (ETDEWEB)

Tandon, L. (Lav); Eglin, J. L. (Judith Lynn); Michalak, S. E. (Sarah E.); Picard, R. R.; Temer, D. J. (Donald J.)

2004-01-01

The Rocky Flats Plutonium (Pu) Metal Sample Exchange program was conducted to insure the quality and intercomparability of measurements such as Pu assay, Pu isotopics, and impurity analyses. The Rocky Flats program was discontinued in 1989 after more than 30 years. In 2001, Los Alamos National Laboratory (LANL) reestablished the Pu Metal Exchange program. In addition to the Atomic Weapons Establishment (AWE) at Aldermaston, six Department of Energy (DOE) facilities Argonne East, Argonne West, Livermore, Los Alamos, New Brunswick Laboratory, and Savannah River are currently participating in the program. Plutonium metal samples are prepared and distributed to the sites for destructive measurements to determine elemental concentration, isotopic abundance, and both metallic and nonmetallic impurity levels. The program provides independent verification of analytical measurement capabilies for each participating facility and allows problems in analytical methods to be identified. The current status of the program will be discussed with emphasis on the unique statistical analysis and modeling of the data developed for the program. The discussion includes the definition of the consensus values for each analyte (in the presence and absence of anomalous values and/or censored values), and interesting features of the data and the results.

Measurements of plutonium in environmental samples

International Nuclear Information System (INIS)

D'Alberti, F.; Risposi, L.

1996-01-01

Within the activities connected with the start up of the PETRA Laboratory (Processo per l'Estrazione di Terre Rare ed Attinidi, i.e. process for extraction of rare earths and actinides), the Radiation Protection Unit of the J.R.C.-Ispra has carried out a well planned set of experimental measurements aimed at evaluating the zero point of the isotopes of plutonium in environmental samples by alfa spectrometry. After the International Moratorium in 1963, no release of plutonium has occurred in the environment apart from the burn up of SNAP 9A satellite in April 1964. Since then the plutonium concentration in air and in fallout samples has been continuously decreasing requiring, therefore, optimization of both instrumentation and experimental measurement procedures in order to obtain better sensibilities. In this work, the experimental methodology followed at the J.R.C.-Ispra for measurements of plutonium concentration in air, deposition and soil is described and the plutonium behaviour in these samples is reported and discussed starting from 1961

Measurements of plutonium in environmental samples

Energy Technology Data Exchange (ETDEWEB)

D' Alberti, F; Risposi, L [Instituto di Fisica Applicata, University of Milan, Milan (Italy)

1996-01-01

Within the activities connected with the start up of the PETRA Laboratory (Processo per l'Estrazione di Terre Rare ed Attinidi, i.e. process for extraction of rare earths and actinides), the Radiation Protection Unit of the J.R.C.-Ispra has carried out a well planned set of experimental measurements aimed at evaluating the zero point of the isotopes of plutonium in environmental samples by alfa spectrometry. After the International Moratorium in 1963, no release of plutonium has occurred in the environment apart from the burn up of SNAP 9A satellite in April 1964. Since then the plutonium concentration in air and in fallout samples has been continuously decreasing requiring, therefore, optimization of both instrumentation and experimental measurement procedures in order to obtain better sensibilities. In this work, the experimental methodology followed at the J.R.C.-Ispra for measurements of plutonium concentration in air, deposition and soil is described and the plutonium behaviour in these samples is reported and discussed starting from 1961.

Standardization of portable assay instrumentation: the neutron-coincidence tree

International Nuclear Information System (INIS)

Menlove, H.O.

1983-01-01

Standardization of portable neutron assay instrumentation has been achieved by using the neutron coincidence technique as a common basis for a wide range of instruments and applications. The electronics originally developed for the High-Level Neutron Coincidence Counter has been adapted to both passive- and active-assay instrumentation for field verification of bulk plutonium, inventory samples, pellets, powders, nitrates, high-enriched uranium, and materials-testing-reactor, light-water-reactor, and mixed-oxide fuel assemblies. The family of detectors developed at Los Alamos National Laboratory and their performance under in-field conditions are described. 16 figures, 3 tables

Long time contamination from plutonium

Energy Technology Data Exchange (ETDEWEB)

Fueloep, M; Patzeltova, N; Ragan, P [Inst. of Preventive and Clinical Medicine, Bratislava (Slovakia); Matel, L [Comenius Univ., Bratislava (Slovakia). Department of Nuclear Chemistry

1996-12-31

Plutonium isotopes in the organism of the patient (who had participated in the liquidation works after the Chernobyl accident; for three month he had stayed in the epicenter, where he acted as a chauffeur driving a radioactive material to the place of destination) from urine were determined. For determination of the concentration of Pu-239, Pu-240 in urine a modified radiochemical method was used. After mineralization the sample was separated as an anion-nitrate complex with contact by the anion form of the resin in the column. The resin was washed by 8 M HNO{sub 3}, the 8 M HCl with 0.3 M HNO{sub 3} for removing the other radionuclides. The solution 0.36 M HCl with 0.01 M HF was used for the elution of plutonium. Using the lanthanum fluoride technique the sample was filtrated through a membrane filter. The plutonium was detected in the dry sample. The Pu-239 tracer was used for the evaluation of the plutonium separation efficiency. The alpha spectrometric measurements were carried out with a large area silicon detector. The samples were measured and evaluated in the energy region 4.98-5.18 MeV. The detection limit of alpha spectrometry measurements has been 0.01 Bq dm{sup -3}. The concentration of plutonium in the 24-hour urine was determined three times in the quarter year intervals. The results are: 54 mBq, 63.2 mBq, 53 mBq, with average 56,7 mBq. From the results of the analyses of plutonium depositions calculated according to ICRP 54 the intake of this radionuclide for the patient was 56.7 kBq. To estimate a committed effective dose (50 years) from the intake of plutonium was used a conversion factor 6.8.10{sup -5} Sv.Bq{sup -1} (class W). So the expressed committed effective dose received from the plutonium intake is 3.8 Sv. This number is relatively high and all the effective dose will be higher, because the patient was exposed to the other radionuclides too. (Abstract Truncated)

Plutonium recycle. In-core fuel management

International Nuclear Information System (INIS)

Vincent, F.; Berthet, A.; Le Bars, M.

1985-01-01

Plutonium recycle in France will concern a dozen of PWR 900 MWe controlled in gray mode till 1995. This paper presents the main characteristics of fuel management with plutonium recycle. The organization of management studies will be copied from this developed for classical management studies. Up these studies, a ''feasibility report'' aims at establishing at each stage of the fuel cycle, the impact of the utilization of fuel containing plutonium [fr

The plutonium-oxygen and uranium-plutonium-oxygen systems: A thermochemical assessment

International Nuclear Information System (INIS)

1967-01-01

The report of a panel of experts convened by the IAEA in Vienna in March 1964. It reviews the structural and thermodynamic data for the Pu-O and U-Pu-O systems and presents the conclusions of the panel. The report gives information on preparation, phase diagrams, thermodynamic and vaporization behaviour of plutonium oxides, uranium-plutonium oxides and PuO 2 -MeO x (Me=Be, Mg, Al, Si, W, Th, Eu, Zr, Ce) systems. 167 refs, 27 figs, 17 tabs

Qualitative chemical analysis of plutonium by Alpha spectroscopy

International Nuclear Information System (INIS)

Ramirez G, J Qumica.J.

1994-01-01

In this work the separation and purification of plutonium from irradiated uranium was done. The plutonium, produced by the irradiation of uranium in a nuclear reactor and the β decay of 239 Np, was stabilized to Pu +4 with sodium nitrite. Plutonium was separated from the fission products and uranium by ion exchange using the resin Ag 1 X 8. It was electrodeposited on stainless steel discs and the alpha radioactivity of plutonium was measured in a surface barrier detector. The results showed that plutonium was separated with a radiochemical purity higher than 99 %. (Author)

IMPROVED PROCESS OF PLUTONIUM CARRIER PRECIPITATION

Science.gov (United States)

Faris, B.F.

1959-06-30

This patent relates to an improvement in the bismuth phosphate process for separating and recovering plutonium from neutron irradiated uranium, resulting in improved decontamination even without the use of scavenging precipitates in the by-product precipitation step and subsequently more complete recovery of the plutonium in the product precipitation step. This improvement is achieved by addition of fluomolybdic acid, or a water soluble fluomolybdate, such as the ammonium, sodium, or potassium salt thereof, to the aqueous nitric acid solution containing tetravalent plutonium ions and contaminating fission products, so as to establish a fluomolybdate ion concentration of about 0.05 M. The solution is then treated to form the bismuth phosphate plutonium carrying precipitate.

International shipment of plutonium by air

International Nuclear Information System (INIS)

Mercado, J.E.; McGrogan, J.P.

1995-05-01

In support of the United States (US) Government's decision to place excess plutonium oxide at the US Department of Energy's (DOE) Hanford Site under International Atomic Energy Agency (IAEA) safeguards, the Department of State notified the Congress that a plutonium storage vault at the Plutonium Finishing Plant at the Hanford Site would be added to the eligible facilities list. As part of the preparations to transfer the plutonium oxide under IAEA safeguards, samples of the powder were taken from the inventory to be shipped to the IAEA headquarters in Vienna, Austria, for laboratory analysis. The analysis of these samples was of high priority, and the IAEA requested that the material be shipped by aircraft, the most expeditious method

Chemical Disposition of Plutonium in Hanford Site Tank Wastes

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jones, Susan A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-05-07

This report examines the chemical disposition of plutonium (Pu) in Hanford Site tank wastes, by itself and in its observed and potential interactions with the neutron absorbers aluminum (Al), cadmium (Cd), chromium (Cr), iron (Fe), manganese (Mn), nickel (Ni), and sodium (Na). Consideration also is given to the interactions of plutonium with uranium (U). No consideration of the disposition of uranium itself as an element with fissile isotopes is considered except tangentially with respect to its interaction as an absorber for plutonium. The report begins with a brief review of Hanford Site plutonium processes, examining the various means used to recover plutonium from irradiated fuel and from scrap, and also examines the intermediate processing of plutonium to prepare useful chemical forms. The paper provides an overview of Hanford tank defined-waste–type compositions and some calculations of the ratios of plutonium to absorber elements in these waste types and in individual waste analyses. These assessments are based on Hanford tank waste inventory data derived from separately published, expert assessments of tank disposal records, process flowsheets, and chemical/radiochemical analyses. This work also investigates the distribution and expected speciation of plutonium in tank waste solution and solid phases. For the solid phases, both pure plutonium compounds and plutonium interactions with absorber elements are considered. These assessments of plutonium chemistry are based largely on analyses of idealized or simulated tank waste or strongly alkaline systems. The very limited information available on plutonium behavior, disposition, and speciation in genuine tank waste also is discussed. The assessments show that plutonium coprecipitates strongly with chromium, iron, manganese and uranium absorbers. Plutonium’s chemical interactions with aluminum, nickel, and sodium are minimal to non-existent. Credit for neutronic interaction of plutonium with these absorbers

Plutonium safety training course

International Nuclear Information System (INIS)

Moe, H.J.

1976-03-01

This course seeks to achieve two objectives: to provide initial safety training for people just beginning work with plutonium, and to serve as a review and reference source for those already engaged in such work. Numerous references have been included to provide information sources for those wishing to pursue certain topics more fully. The first part of the course content deals with the general safety approach used in dealing with hazardous materials. Following is a discussion of the four properties of plutonium that lead to potential hazards: radioactivity, toxicity, nuclear properties, and spontaneous ignition. Next, the various hazards arising from these properties are treated. The relative hazards of both internal and external radiation sources are discussed, as well as the specific hazards when plutonium is the source. Similarly, the general hazards involved in a criticality, fire, or explosion are treated. Comments are made concerning the specific hazards when plutonium is involved. A brief summary comparison between the hazards of the transplutonium nuclides relative to 239 Pu follows. The final portion deals with control procedures with respect to contamination, internal and external exposure, nuclear safety, and fire protection. The philosophy and approach to emergency planning are also discussed

Disposal of Surplus Weapons Grade Plutonium

International Nuclear Information System (INIS)

Alsaed, H.; Gottlieb, P.

2000-01-01

The Office of Fissile Materials Disposition is responsible for disposing of inventories of surplus US weapons-usable plutonium and highly enriched uranium as well as providing, technical support for, and ultimate implementation of, efforts to obtain reciprocal disposition of surplus Russian plutonium. On January 4, 2000, the Department of Energy issued a Record of Decision to dispose of up to 50 metric tons of surplus weapons-grade plutonium using two methods. Up to 17 metric tons of surplus plutonium will be immobilized in a ceramic form, placed in cans and embedded in large canisters containing high-level vitrified waste for ultimate disposal in a geologic repository. Approximately 33 metric tons of surplus plutonium will be used to fabricate MOX fuel (mixed oxide fuel, having less than 5% plutonium-239 as the primary fissile material in a uranium-235 carrier matrix). The MOX fuel will be used to produce electricity in existing domestic commercial nuclear reactors. This paper reports the major waste-package-related, long-term disposal impacts of the two waste forms that would be used to accomplish this mission. Particular emphasis is placed on the possibility of criticality. These results are taken from a summary report published earlier this year

Pulmonary carcinogenesis from plutonium-containing particles

International Nuclear Information System (INIS)

Thomas, R.G.; Smith, D.M.; Anderson, E.C.

1980-01-01

Induction of lung tumors by various types of radiation is of paramount concern to the nuclear industry. The data presented were obtained by exposing the pulmonary system of Syrian hamsters to particles of zirconium oxide containing various amounts of either plutonium-238 or -239 as the alpha radiation source. These particles were injected intravenously and lodged permanently in the capillary bed of the lung. When less than 20% of the lung tissue was irradiated, simulating the ''hot particle'' mode, tumors were not evident with lung burdens up to 500 nCi plutonium. More diffuse irradiation significantly increased the tumor incidence, with lung burdens of 50 to 150 nCi. When plutonium-laden microspheres were administered intratracheally, tumor production was considerably increased and the addition of 3 mg of iron oxide intratracheally further increased the incidence. Using the zirconium oxide matrix for the carrier of plutonium in aerosol particles produced tumor incidences of up to 50% in Syrian hamsters exposed by inhalation. Initial pulmonary (alveolar) burdens reached 100 nCi of plutonium. Similar inhalation studies using plutonium dioxide alone (no matrix) failed to produce any increase in lung tumorigenesis. The results are discussed in terms of possible mechanisms necessary for lung carcinogenesis. (H.K.)

Verification station for Sandia/Rockwell Plutonium Protection system

International Nuclear Information System (INIS)

Nicholson, N.; Hastings, R.D.; Henry, C.N.; Millegan, D.R.

1979-04-01

A verification station has been designed to confirm the presence of plutonium within a container module. These container modules [about 13 cm (5 in.) in diameter and 23 cm (9 in.) high] hold sealed food-pack cans containing either plutonium oxide or metal and were designed by Sandia Laboratories to provide security and continuous surveillance and safety. After the plutonium is placed in the container module, it is closed with a solder seal. The verification station discussed here is used to confirm the presence of plutonium in the container module before it is placed in a carousel-type storage array inside the plutonium storage vault. This measurement represents the only technique that uses nuclear detectors in the plutonium protection system

The economics of plutonium recycle

International Nuclear Information System (INIS)

James, R.A.

1977-11-01

The individual cost components and the total fuel cycle costs for natural uranium and uranium-plutonium mixed oxide fuel cycles for CANDU-PHW reactors are discussed. A calculation is performed to establish the economic conditions under which plutonium recycle would be economically attractive. (auth)

Plutonium uniqueness

International Nuclear Information System (INIS)

Silver, G.L.

1984-01-01

A standard is suggested against which the putative uniqueness of plutonium may be tested. It is common folklore that plutonium is unique among the chemical elements because its four common oxidation states can coexist in the same solution. Whether this putative uniqueness appears only during transit to equilibrium, or only at equilibrium, or all of the time, is not generally made clear. But while the folklore may contain some truth, it cannot be put to test until some measure of 'uniqueness' is agreed upon so that quantitative comparisons are possible. One way of measuring uniqueness is as the magnitude of the product of the mole fractions of the element at equilibrium. A 'coexistence index' is defined and discussed. (author)

Determination of plutonium in soils by mass spectrometry

International Nuclear Information System (INIS)

Storms, H.A.; Carlson, D.C.; Hunter, F.F.

1974-01-01

A procedure is described in which mass spectrometry is utilized for the determination of plutonium in soils. Using this procedure we have measured plutonium isotopic compositions at concentrations as low as 2 x 10 -14 grams Pu per gram soil. A thermal ionization source with canoe-shaped rhenium filament, is utilized in the mass spectrometer. The plutonium, when loaded onto the filament, is contained in a single Dowex-1 resin bead which is about 350 micrometers in diameter. Concentrating the plutonium within this single bead is a key step in the procedure and produces a relatively clean plutonium fraction. The resin bead also serves as an effective diffusion barrier such that the plutonium is prevented from being removed with the lower boiling impurities. The Pu remains in the bead until the temperature is sufficiently high for efficient production of Pu + ions. Plutonium ionization efficiencies as high as 2.5 percent have been measured

Surplus plutonium disposition draft environmental impact statement. Volume 2

International Nuclear Information System (INIS)

1998-07-01

On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel. Volume 2 contains the appendices to the report and describe the following: Federal Register notices; contractor nondisclosure statement; adjunct melter

Addressing mixed waste in plutonium processing

International Nuclear Information System (INIS)

Christensen, D.C.; Sohn, C.L.; Reid, R.A.

1991-01-01

The overall goal is the minimization of all waste generated in actinide processing facilities. Current emphasis is directed toward reducing and managing mixed waste in plutonium processing facilities. More specifically, the focus is on prioritizing plutonium processing technologies for development that will address major problems in mixed waste management. A five step methodological approach to identify, analyze, solve, and initiate corrective action for mixed waste problems in plutonium processing facilities has been developed

Magnetic separation as a plutonium residue enrichment process

International Nuclear Information System (INIS)

Avens, L.R.; Gallegos, U.F.; McFarlan, J.T.

1990-01-01

Several plutonium contaminated residues have been subjected to Open Gradient Magnetic Separation (OGMS) on an experimental scale. OGMS experiments on graphite and bomb reduction residues resulted in a plutonium rich fraction and a plutonium lean fraction. Values for the bulk quantity rejected to the lean fraction varied between about 20% to 85% of the feed bulk. The plutonium content of the lean fraction can be reduced from about 2% in the feed to the 0.1% to 0.5% range dependent on the portion of the feed rejected to this lean fraction. These values are low enough in plutonium to meet economic discard limits and be considered for direct discard. Magnetic separation of pyrochemical salts gave less favorable results. While a fraction very rich in plutonium could be obtained, the lean fraction plutonium content was too high for direct discard. This may still have chemical processing applications. OGMS experiments at low magnetic field strength on incinerator ash did give two fractions but the plutonium content of each fraction was essentially identical. Thus, no chemical processing advantage was identified for magnetic separation of this residue. 6 refs., 1 fig., 9 tabs

Nondestructive assay methods for irradiated nuclear fuels

International Nuclear Information System (INIS)

Hsue, S.T.; Crane, T.W.; Talbert, W.L. Jr.; Lee, J.C.

1978-01-01

This report is a review of the status of nondestructive assay (NDA) methods used to determine burnup and fissile content of irradiated nuclear fuels. The gamma-spectroscopy method measures gamma activities of certain fission products that are proportional to the burnup. Problems associated with this method are migration of the fission products and gamma-ray attenuation through the relatively dense fuel material. The attenuation correction is complicated by generally unknown activity distributions within the assemblies. The neutron methods, which usually involve active interrogation and prompt or delayed signal counting, are designed to assay the fissile content of the spent-fuel elements. Systems to assay highly enriched spent-fuel assemblies have been tested extensively. Feasibility studies have been reported of systems to assay light-water reactor spent-fuel assemblies. The slowing-down spectrometer and neutron resonance absorption methods can distinguish between the uranium and plutonium fissile contents, but they are limited to the assay of individual rods. We have summarized the status of NDA techniques for spent-fuel assay and present some subjects in need of further investigation. Accuracy of the burnup calculations for power reactors is also reviewed

Spectrographic analysis of plutonium (1960); L'analyse spectrographique du plutonium (1960)

Energy Technology Data Exchange (ETDEWEB)

Artaud, J; Chaput, M; Robichet, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

Various possibilities for the spectrographic determination of impurities in plutonium are considered. The application of the 'copper spark' method, of sparking on graphite and of fractional distillation in the arc are described and discussed in some detail (apparatus, accessories, results obtained). (author) [French] On examine diverses possibilites pour le dosage spectrographique des impuretes dans le plutonium. On decrit et discute plus particulierement de l'application des methodes 'copper spark', de l'etincelage sur graphite et de la distillation fractionnee dans l'arc (montages, accessoires, resultats obtenus). (auteur)

Nondestructive assay of sale materials

International Nuclear Information System (INIS)

Rodenburg, W.W.; Fleissner, J.G.

1981-01-01

This paper covers three primary areas: (1) reasons for performing nondestructive assay on SALE materials; (2) techniques used; and (3) discussion of investigators' revised results. The study shows that nondestructive calorimetric assay of plutonium offers a viable alternative to traditional wet chemical techniques. For these samples, the precision ranged from 0.4 to 0.6% with biases less than 0.2%. Thus, for those materials where sampling errors are the predominant source of uncertainty, this technique can provide improved accuracy and precision while saving time and money as well as reducing the amount of liquid wastes to be handled. In addition, high resolution gamma-ray spectroscopy measurements of solids can provide isotopic analysis data in a cost effective and timely manner. The timeliness of the method can be especially useful to the plant operator for production control and quality control measurements

Monitoring of wastes containing plutonium. Necessity and method

International Nuclear Information System (INIS)

Sousselier, Y.; Pottier, P.

1979-01-01

Importance of problems set by wastes containing plutonium is rapidly growing. Plutonium is not a waste, recycling limits heavily the quantity of plutonium to be stored with wastes. Optimized waste management must take definitive storage and economical limits of plutonium recovery into account. Waste monitoring is a must for safety, economy and waste management. Methods used require reliability, simplicity, sensibility and accuracy particularly for threshold detection [fr

Plutonium in the ocean environment. Its distributions and behavior

International Nuclear Information System (INIS)

Hirose, Katsumi

2009-01-01

Marine environments have been extensively contaminated by plutonium as a result of global fallout due to atmospheric nuclear-weapons testing. Knowledge of the levels and behavior of plutonium in marine environments is necessary to assess the radiological and ecological effects of plutonium. Such analytical techniques as radiochemical analysis, α-spectrometry, and mass spectrometry have been developed to analyze the plutonium in seawater over the past five decades. Because of complex chemical properties (e.g. high reactivity to particles), plutonium in the ocean exhibits more complicated behavior than other long-lived anthropogenic radionuclides, such as 137 Cs. In the present study. In reviewed the research history of plutonium in the ocean, including spatial and temporal changes of plutonium levels and distributions, and its oceanographic behavior. (author)

Extraction and purification of plutonium by a tertiary amine; Extraction et purification du plutonium par une amine tertiaire

Energy Technology Data Exchange (ETDEWEB)

Trentinian, M de; Chesne, A [Commissariat a l' Energie Atomique, Fontenay aux Roses, Section de Chimie des Actimides (France).Centre d' Etudes Nucleaires; Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

Trilaurylamine diluted with a paraffinic solvent (dodecane) was studied as part of the research dealing with the separation and purification of plutonium. The physical properties (solubility of nitrates in the amine as a function of temperature) and the resistance to radiations of this substance were examined. The extraction characteristics of nitric solutions of plutonium, uranium and certain fission products are given as a function of the following factors: concentration of the various ions in solution, valency states. A method of plutonium purification based on these results is presented. (author) [French] La trilaurylamine diluee par un solvant paraffinique (dodecane) a ete etudiee dans le cadre des recherches concernant la separation et la purification du plutonium. Une etude des caracteres physiques (solubilite des nitrates dans l'amine en fonction de la temperature) s'ajoute a celle de la tenue aux radiations de ce corps. Les caracteristiques d'extraction de solutions nitriques de plutonium, uranium, et certains produits de fission, sont donnes en fonction des facteurs suivants: concentration des differents ions en solution, etats de valence. On presente une methode de purification du plutonium basee sur ces resultats. (auteur)

Evaluation of plutonium at Enewetak Atoll

International Nuclear Information System (INIS)

Wilson, D.W.; Ng, Y.C.; Robison, W.L.

1975-01-01

An extensive survey was carried out in 1972 to 1973 to assess the current radiological status of Enewetok Atoll. The radionuclides detected in the Atoll environment were studied for their potential contributions to the dose commitment of the returning population according to several pathways of exposure. Plutonium was detected in air and in the terrestrial and aquatic environment at concentrations that varied from background levels due to world-wide fallout to levels several orders-of-magnitude above. The dose commitments from plutonium via the terrestrial food chain and inhalation vary according to the postulated living pattern. The dosages via marine foods can be expected to be insensitive to living pattern and to exceed those via terrestrial foods. Plutonium would contribute nearly all of the dosage via inhalation, but this pathway ranks low in overall importance compared with the food-chain and external-dose pathways. Although the potential dose from plutonium via all pathways is low relative to that from 60 Co, 90 Sr and 137 Cs, plutonium will still remain in the Atoll environment after the other makor isotopes have decayed away. (author)

Long-term plutonium storage: Design concepts

International Nuclear Information System (INIS)

Wilkey, D.D.; Wood, W.T.; Guenther, C.D.

1994-01-01

An important part of the Department of Energy (DOE) Weapons Complex Reconfiguration (WCR) Program is the development of facilities for long-term storage of plutonium. The WCR design goals are to provide storage for metals, oxides, pits, and fuel-grade plutonium, including material being held as part of the Strategic Reserve and excess material. Major activities associated with plutonium storage are sorting the plutonium inventory, material handling and storage support, shipping and receiving, and surveillance of material in storage for both safety evaluations and safeguards and security. A variety of methods for plutonium storage have been used, both within the DOE weapons complex and by external organizations. This paper discusses the advantages and disadvantages of proposed storage concepts based upon functional criteria. The concepts discussed include floor wells, vertical and horizontal sleeves, warehouse storage on vertical racks, and modular storage units. Issues/factors considered in determining a preferred design include operational efficiency, maintenance and repair, environmental impact, radiation and criticality safety, safeguards and security, heat removal, waste minimization, international inspection requirements, and construction and operational costs

Kalman filter analysis of delayed neutron nondestructive assay measurements

International Nuclear Information System (INIS)

Aumeier, S. E.

1998-01-01

The ability to nondestructively determine the presence and quantity of fissile and fertile nuclei in various matrices is important in several nuclear applications including international and domestics safeguards, radioactive waste characterization and nuclear facility operations. Material irradiation followed by delayed neutron counting is a well known and useful nondestructive assay technique used to determine the fissile-effective content of assay samples. Previous studies have demonstrated the feasibility of using Kalman filters to unfold individual isotopic contributions to delayed neutron measurements resulting from the assay of mixes of uranium and plutonium isotopes. However, the studies in question used simulated measurement data and idealized parameters. We present the results of the Kalman filter analysis of several measurements of U/Pu mixes taken using Argonne National Laboratory's delayed neutron nondestructive assay device. The results demonstrate the use of Kalman filters as a signal processing tool to determine the fissile and fertile isotopic content of an assay sample from the aggregate delayed neutron response following neutron irradiation

Technical considerations and policy requirements for plutonium management

International Nuclear Information System (INIS)

Christensen, D.C.; Dinehart, S.M.; Yarbro, S.L.

1995-01-01

The goals for plutonium management have changed dramatically over the past few years. Today, the challenge is focused on isolating plutonium from the environment and preparing it for permanent disposition. In parallel, the requirements for managing plutonium are rapidly changing. For example, there is a significant increase in public awareness on how facilities operate, increased attention to environmental safety and health (ES and H) concerns, greater interest in minimizing waste, more emphasis on protecting material from theft, providing materials for international inspection, and a resurgence of interest in using plutonium as an energy source. Of highest concern, in the immediate future, is protecting plutonium from theft or diversion, while the national policy on disposition is debated. These expanded requirements are causing a broadening of responsibilities within the Department of Energy (DOE) to include at least seven organizations. An unavoidable consequence is the divergence in approach and short-term goals for managing similar materials within each organization. The technology base does exist, properly, safely, and cost effectively to extract plutonium from excess weapons, residues, waste, and contaminated equipment and facilities, and to properly stabilize it. Extracting the plutonium enables it to be easily inventoried, packaged, and managed to minimize the risk of theft and diversion. Discarding excess plutonium does not sufficiently reduce the risk of diversion, and as a result, long-term containment of plutonium from the environment may not be able to be proven to the satisfaction of the public

Technical considerations and policy requirements for plutonium management

International Nuclear Information System (INIS)

Christensen, D.C.; Dinehart, S.M.; Yarbro, S.L.

1996-01-01

The goals for plutonium management have changed dramatically over the past few years. Today, the challenge is focused on isolating plutonium from the environment and preparing it for permanent disposition. In parallel, the requirements for managing plutonium are rapidly changing. For example, there is a significant increase in public awareness on how facilities operate, increased attention to environmental safety and health (ES and H) concerns, greater interest in minimizing waste, more emphasis on protecting material from theft, providing materials for international inspection, and a resurgence of interest in using plutonium as an energy source. Of highest concern, in the immediate future, is protecting plutonium from theft or diversion, while the national policy on disposition is debated. These expanded requirements are causing a broadening of responsibilities within the Department of Energy (DOE) to include at least seven organizations. An unavoidable consequence is the divergence in approach and short-term goals for managing similar materials within each organization. The technology base does exist, properly, safely, and cost effectively to extract plutonium from excess weapons, residues, waste, and contaminated equipment and facilities, and to properly stabilize it. Extracting the plutonium enables it to be easily inventoried, packaged, and managed to minimize the risk of theft and diversion. Discarding excess plutonium does not sufficient reduce the risk of diversion, and as a result, long-term containment of plutonium from the environment may not be able to be proven to the satisfaction of the public

Plutonium again (smuggling and movements)

International Nuclear Information System (INIS)

Anon.

1994-01-01

A link is discounted between nuclear proliferation and the recently discovered smuggled plutonium from the former Soviet Union at Munich airport and other places in Germany. It is argued that governments wishing to obtain nuclear materials to develop a weapons programme would not arrange to have it smuggled in a suitcase. Instead, it is speculated that a link exists between the plutonium smuggling incidents and the desire to promote the production of mixed oxide (MOX) fuel. Such incidents, by further raising public anxiety, may be intended to turn public opinion in favour of MOX fuel production as a sensible way of getting rid of surplus plutonium. (UK)

Plutonium disposition via immobilization in ceramic or glass

Energy Technology Data Exchange (ETDEWEB)

Gray, L.W.; Kan, T.; Shaw, H.F.; Armantrout, A.

1997-03-05

The management of surplus weapons plutonium is an important and urgent task with profound environmental, national, and international security implications. In the aftermath of the Cold War, Presidential Policy Directive 13, and various analyses by renown scientific, technical, and international policy organizations have brought about a focused effort within the Department of Energy to identify and implement paths for the long term disposition of surplus weapons- usable plutonium. The central goal of this effort is to render surplus weapons plutonium as inaccessible and unattractive for reuse in nuclear weapons as the much larger and growing stock of plutonium contained in spent fuel from civilian reactors. One disposition option being considered for surplus plutonium is immobilization, in which the plutonium would be incorporated into a glass or ceramic material that would ultimately be entombed permanently in a geologic repository for high-level waste.

Preparation of plutonium hexafluoride. Recovery of plutonium from waste dross (1962)

International Nuclear Information System (INIS)

Gendre, R.

1962-01-01

The object of this work is to study the influence of various physical factors on the rate of fluorination of solid plutonium tetrafluoride by fluorine. In a horizontal oven with a circulation for pure fluorine at atmospheric pressure and 520 deg. C, at a fluorine rate of 9 litres/hour, it is possible to transform 3 g of tetrafluoride to hexafluoride with about 100 per cent transformation and a recovery yield of over 90 per cent, in 4 to 5 hours. The fluorination rate is a function of the temperature, of the fluorine flow-rate, of the crucible surface, of the depth of the tetrafluoride layer and of the reaction time. It does not depend on the diffusion of the fluorine into the solid but is determined by the reaction at the gas-solid interface and obeys the kinetic law (1 - T T ) 1/3 = kt + 1. The existence of intermediate fluorides, in particular Pu 4 F 17 , is confirmed by a break in the Arrhenius plot at about 370 deg. C, by differences in the fluorination rates inside the tetrafluoride layer, and by reversible colour changes. The transformation to hexafluoride occurs with a purification with respect of the foreign elements present in the initial plutonium. Recovery of plutonium from waste dross: The study is based on the transformation of occluded plutonium particles to gaseous hexafluoride which is then decomposed thermally to the tetrafluoride which can be reintroduced directly in the production circuit. Under the conditions considered this process is not applicable industrially. After milling, it is possible to separate the dross into enriched (75 per cent Pu in 2.6 per cent by weight of dross) and depleted portions. By prolonged fluorination (16 hours) of the various fractions it is possible to recover about 80 per cent of the plutonium. A treatment plant using fluidization, as described at the end of this study, should make it possible to substantially improve the yield. (author) [fr

Plutonium decontamination studies using Reverse Osmosis

International Nuclear Information System (INIS)

Plock, C.E.; Travis, T.N.

1980-01-01

Water in batches of 45 gallons each, from a creek crossing the Rocky Flats Plant, was transferred to the Reverse Osmosis (RO) laboratory for experimental testing. The testing involved using RO for plutonium decontamination. For each test, the water was spiked with plutonium, had its pH adjusted, and was then processed by RO. At a water recovery level of 87%, the plutonium decontamination factors ranged from near 100 to 1200, depending on the pH of the processed water

Uranium-plutonium fuel for fast reactors

International Nuclear Information System (INIS)

Antipov, S.A.; Astafiev, V.A.; Clouchenkov, A.E.; Gustchin, K.I.; Menshikova, T.S.

1996-01-01

Technology was established for fabrication of MOX fuel pellets from co-precipitated and mechanically blended mixed oxides. Both processes ensure the homogeneous structure of pellets readily dissolvable in nitric acid upon reprocessing. In order to increase the plutonium charge in a reactor-burner a process was tested for producing MOX fuel with higher content of plutonium and an inert diluent. It was shown that it is feasible to produce fuel having homogeneous structure and the content of plutonium up to 45% mass

Evaluation of SAR procedures for D-e determination using single aliquots of quartz from two archaeological sites in South Africa

CSIR Research Space (South Africa)

Jacobs, Z

2006-05-01

Full Text Available stimulation between cycles in the SAR procedure were measured for dose recovery tests. The effects of these changes on measurement of D-e values for single aliquots of these two samples are reported. Both modifications improved D-e recovery, and the study...

Elaboration and characterisation of plutonium waste reference materials

International Nuclear Information System (INIS)

Perolat, J.P.

1990-01-01

The Analysis Methods Establishment Commission (CETAMA) has set up a program for the elaboration and characterisation of plutonium waste reference materials. The object of this program is to give laboratories the possibility to test and calibrate apparatus used in non-destructive methods for the analysis of plutonium waste. The different parameters of this program are presented: - characterisation of plutonium, - type and number of containers, - plutonium distribution inside the different containers, - description of the matrix

The extraction of plutonium with triethylene glycol dichloride

International Nuclear Information System (INIS)

Aikin, A.M.; Moss, M.; Bruce, T.

1951-03-01

The extraction of plutonium by triethylene glycol dichloride (trigly) has been investigated briefly. The effect of (1) the valence state of the plutonium, (2) the concentration of nitric acid, (3) the concentration of ammonium nitrate and (4) the conditioning of the trigly was measured. The solubility of plutonium IV in trigly was found to be 70 mgms/ml. Solutions of plutonium in trigly and in concentrated nitric acid solutions have been examined spectrophotometrically. (author)

The extraction of plutonium with triethylene glycol dichloride

Energy Technology Data Exchange (ETDEWEB)

Aikin, A M; Moss, M; Bruce, T

1951-03-15

The extraction of plutonium by triethylene glycol dichloride (trigly) has been investigated briefly. The effect of (1) the valence state of the plutonium, (2) the concentration of nitric acid, (3) the concentration of ammonium nitrate and (4) the conditioning of the trigly was measured. The solubility of plutonium IV in trigly was found to be 70 mgms/ml. Solutions of plutonium in trigly and in concentrated nitric acid solutions have been examined spectrophotometrically. (author)

Study of plutonium multi-recycle in high moderation LWR cores

International Nuclear Information System (INIS)

Iwata, Yutaka; Yamamoto, Toru; Ueji, Masao; Hibi, Koki; Aoyama, Motoo; Sakurada, Koichi

2000-01-01

Nuclear Power Engineering Corporation (NUPEC) has been studying advanced cores that are dedicated to enhance the plutonium consumption per recycling for effective use of plutonium. In this study, a fissile plutonium consumption rate is adopted as an index of the effective use of plutonium, which is defined as a ratio of consumption to loading of fissile plutonium in a core. High moderation core concepts have been studied in order to increase this index based on full MOX cores in the latest designs of LWRs in Japan that are the Advanced Boiling Water Reactor (ABWR) and the Advanced Pressurized Water Reactor (APWR). As a part of this study, core performance in the case of plutonium multi-recycling has been surveyed with these higher moderation cores aiming further effective use of plutonium. The design and analyses for equilibrium cores show that nuclear and thermal hydraulics parameters satisfy design criteria, and a fissile plutonium consumption rate increases up to 20% for ABWRs and 30% for APWRs even in plutonium multi-recycling condition. It was confirmed that the high moderation cores are feasible from a viewpoint of nuclear and thermal hydraulics, safety and plutonium consumption in the condition of plutonium multi-recycling. (author)

Computer-determined assay time based on preset precision

International Nuclear Information System (INIS)

Foster, L.A.; Hagan, R.; Martin, E.R.; Wachter, J.R.; Bonner, C.A.; Malcom, J.E.

1994-01-01

Most current assay systems for special nuclear materials (SNM) operate on the principle of a fixed assay time which provides acceptable measurement precision without sacrificing the required throughput of the instrument. Waste items to be assayed for SNM content can contain a wide range of nuclear material. Counting all items for the same preset assay time results in a wide range of measurement precision and wastes time at the upper end of the calibration range. A short time sample taken at the beginning of the assay could optimize the analysis time on the basis of the required measurement precision. To illustrate the technique of automatically determining the assay time, measurements were made with a segmented gamma scanner at the Plutonium Facility of Los Alamos National Laboratory with the assay time for each segment determined by counting statistics in that segment. Segments with very little SNM were quickly determined to be below the lower limit of the measurement range and the measurement was stopped. Segments with significant SNM were optimally assays to the preset precision. With this method the total assay time for each item is determined by the desired preset precision. This report describes the precision-based algorithm and presents the results of measurements made to test its validity

Civil plutonium held in France in December 31, 2000

International Nuclear Information System (INIS)

2002-02-01

Spent fuels comprise about 1% of plutonium which is separated during the reprocessing and recycled to prepare the mixed uranium-plutonium fuel (MOX), which in turn is burnt in PWRs. Plutonium can be in a non-irradiated or separated form, or in an irradiated form when contained in the spent fuel. Each year, in accordance with the 1997 directives relative to the management of plutonium, France has to make a status of its civil plutonium stock and communicate it to the IAEA using a standard model form. This short document summarizes the French plutonium stocks at the end of 1999 and 2000. (J.S.)

Plutonium determination by isotope dilution

International Nuclear Information System (INIS)

Lucas, M.

1980-01-01

The principle is to add to a known amount of the analysed solution a known amount of a spike solution consisting of plutonium 242. The isotopic composition of the resulting mixture is then determined by surface ionization mass spectrometry, and the plutonium concentration in the solution is deduced, from this measurement. For irradiated fuels neutronic studies or for fissile materials balance measurements, requiring the knowledge of the ratio U/Pu or of concentration both uranium and plutonium, it is better to use the double spike isotope dilution method, with a spike solution of known 233 U- 242 Pu ratio. Using this method, the ratio of uranium to plutonium concentration in the irradiated fuel solution can be determined without any accurate measurement of the mixed amounts of sample and spike solutions. For fissile material balance measurements, the uranium concentration is determined by using single isotope dilution, and the plutonium concentration is deduced from the ratio Pu/U and U concentration. The main advantages of isotope dilution are its selectivity, accuracy and very high sensitivity. The recent improvements made to surface ionization mass spectrometers have considerably increased the precision of the measurements; a relative precision of about 0.2% to 0.3% is obtained currently, but it could be reduced to 0.1%, in the future, with a careful control of the experimental procedures. The detection limite is around 0.1 ppb [fr

Quality control assessment of human immunodeficiency virus type 2 (HIV-2) viral load quantification assays: results from an international collaboration on HIV-2 infection in 2006

NARCIS (Netherlands)

Damond, Florence; Benard, Antoine; Ruelle, Jean; Alabi, Abraham; Kupfer, Bernd; Gomes, Perpetua; Rodes, Berta; Albert, Jan; Böni, Jürg; Garson, Jeremy; Ferns, Bridget; Matheron, Sophie; Chene, Geneviève; Brun-Vezinet, Françoise; Goubau, Patrick; Campa, Pauline; Descamps, Diane; Simon, François; Taieb, Audrey; Autran, Brigitte; Cotten, Matt; Jaye, Assan; Peterson, Kevin; Rowland-Jones, Sarah; Rockstroh, Jürgen; Schwarze-Zander, Carolynne; de Wolf, Frank; van Sighem, Ard; Reiss, Peter; van der Loeff, Maarten Schim; Schutten, Martin; Camacho, Ricardo; Mansinho, Kamal; Antunes, Francisco; Luis, Franca; Valadas, Emilia; Toro, Carlos; Soriano, Vicente; Gyllensten, Katarina; Sonnerborg, Anders; Yilmaz, Aylin; Gisslén, Magnus; Calmy, Alexandra; Rickenbach, Martin; Pillay, Deenan; Tosswill, Jennifer; Anderson, Jane; Chadwick, David

2008-01-01

Human immunodeficiency virus type 2 (HIV-2) RNA quantification assays used in nine laboratories of the ACHI(E)V(2E) (A Collaboration on HIV-2 Infection) study group were evaluated. In a blinded experimental design, laboratories quantified three series of aliquots of an HIV-2 subtype A strain, each

Plutonium and americium separation from salts

International Nuclear Information System (INIS)

Hagan, P.G.; Miner, F.J.

1976-01-01

Salts or materials containing plutonium and americium are dissolved in hydrochloric acid, heated, and contacted with an alkali metal carbonate solution to precipitate plutonium and americium carbonates which are thereafter readily separable from the solution

Work at Aldermaston on plutonium binding with biological systems

International Nuclear Information System (INIS)

Popplewell, D.S.

1976-01-01

Over a number of years, the Chemistry Division of AWRE, Aldermaston, studied the nature of plutonium in various biological systems. The object of the work was to identify those natural products of the body which play a part in the transport and deposition of accidental intakes of plutonium. These results should be of value in formulating more effective therapeutic measures for plutonium removal from the body. The paper reviews the work at AWRE on the interaction of plutonium with serum and rat liver. Experiments on the uptake of plutonium into cell cultures are described. The aim of these experiments was to see whether a model system could be set up for testing the efficacy by which chelating agents could remove plutonium from within cells. A simple hypothesis is presented for the mode of transport of plutonium within animals. (author)

Distribution coefficient of plutonium between sediment and seawater

International Nuclear Information System (INIS)

Duursma, E.K.; Parsi, P.

1974-01-01

Using plutonium 237 as a tracer, a series of experiments were conducted to determine the distribution coefficient of plutonium onto sediments both under oxic and anoxic conditions, where the plutonium was added to seawater in three different valence states: III, IV and VI

Validation of a quantitative cerebrospinal fluid alpha-synuclein assay in a European-wide interlaboratory study

DEFF Research Database (Denmark)

Kruse, N.; Persson, S.; Alcolea, D.

2015-01-01

(one lot) were provided centrally and data reported back to one laboratory for data analysis. Our study showed that although factors such as preanalytical sample handling and lot-to-lot variability were minimized by our study design, we identified high variation in absolute values of CSF aSyn even when...... the same samples and same lots of assays were applied. We further demonstrate that although absolute concentrations differ between laboratories the quantitative results are comparable. With further standardization this assay may become an attractive tool for comparing aSyn measurements in diverse settings...... assay (ELISA) for the quantification of aSyn in CSF, we carried out a round robin trial with 18 participating laboratories trained in CSF ELISA analyses within the BIOMARKAPD project in the EU Joint Program -Neurodegenerative Disease Research. CSF samples (homogeneous aliquots from pools) and ELISA kits...

HENC performance evaluation and plutonium calibration

International Nuclear Information System (INIS)

Menlove, H.O.; Baca, J.; Pecos, J.M.; Davidson, D.R.; McElroy, R.D.; Brochu, D.B.

1997-10-01

The authors have designed a high-efficiency neutron counter (HENC) to increase the plutonium content in 200-L waste drums. The counter uses totals neutron counting, coincidence counting, and multiplicity counting to determine the plutonium mass. The HENC was developed as part of a Cooperative Research and Development Agreement between the Department of Energy and Canberra Industries. This report presents the results of the detector modifications, the performance tests, the add-a-source calibration, and the plutonium calibration at Los Alamos National Laboratory (TA-35) in 1996

Plutonium determination by spectrophotometry of plutonium (VI): control of the nuclear fuel reprocessing plant

Energy Technology Data Exchange (ETDEWEB)

Grison, J [Compagnie Generale des Matieres Nucleaires (COGEMA), Centre de la Hague, 50 - Cherbourg (France)

1980-10-01

The plutonium (VI) spectrophotometric determination, after AgO oxidation in 3 M nitric acid medium, is used for the running-control of the nuclear fuel reprocessing plant at La Hague. Analytical device used in glove-box or shielded-cell is briefly described. This method is fast, sensitive, unfailing and gives simple effluents. It is applied by day and night shifts, during Light Water Reactor fuel reprocessing campaign, for 0.5 mg/l up to 20 g/l plutonium solutions. Reference solution measurements have a 0.8 to 1.4 % relative standard deviation; duplicate plutonium determinations give a 0.3% relative standard deviation for sample analysis. There is a discrepancy (- 0.3% to - 0.9%) between the spectrophotometric method results and the isotopic dilution analysis.

Plutonium determination by spectrophotometry of plutonium (VI): control of the nuclear fuel reprocessing plant

International Nuclear Information System (INIS)

Grison, J.

1980-01-01

The plutonium (VI) spectrophotometric determination, after AgO oxidation in 3 M nitric acid medium, is used for the running-control of the nuclear fuel reprocessing plant at La Hague. Analytical device used in glove-box or shielded-cell is briefly described. This method is fast, sensitive, unfailing and gives simple effluents. It is applied by day and night shifts, during Light Water Reactor fuel reprocessing campaign, for 0.5 mg/l up to 20 g/l plutonium solutions. Reference solution measurements have a 0.8 to 1.4 % relative standard deviation; duplicate plutonium determinations give a 0.3% relative standard deviation for sample analysis. There is a discrepancy (- 0.3% to - 0.9%) between the spectrophotometric method results and the isotopic dilution analysis [fr

Fifty years of plutonium exposure to the Manhattan Project plutonium workers: an update.

Science.gov (United States)

Voelz, G L; Lawrence, J N; Johnson, E R

1997-10-01

Twenty-six white male workers who did the original plutonium research and development work at Los Alamos have been examined periodically over the past 50 y to identify possible health effects from internal plutonium depositions. Their effective doses range from 0.1 to 7.2 Sv with a median value of 1.25 Sv. As of the end of 1994, 7 individuals have died compared with an expected 16 deaths based on mortality rates of U.S. white males in the general population. The standardized mortality ratio (SMR) is 0.43. When compared with 876 unexposed Los Alamos workers of the same period, the plutonium worker's mortality rate was also not elevated (SMR = 0.77). The 19 living persons have diseases and physical changes characteristic of a male population with a median age of 72 y (range = 69 to 86 y). Eight of the twenty-six workers have been diagnosed as having one or more cancers, which is within the expected range. The underlying cause of death in three of the seven deceased persons was from cancer, namely cancer of prostate, lung, and bone. Mortality from all cancers was not statistically elevated. The effective doses from plutonium to these individuals are compared with current radiation protection guidelines.

Plutonium recycle in PWR reactors (Brazilian Nuclear Program)

International Nuclear Information System (INIS)

Rubini, L.A.

1978-02-01

An evaluation is made of the material requirements of the nuclear fuel cycle with plutonium recycle. It starts from the calculation of a reference reactor and allows the evaluation of demand under two alternatives of nuclear fuel cycle for Pressurized Water Reactors (PWR): without plutonium recycle; and with plutonium recycle. Calculations of the reference reactor have been carried out with the CELL-CORE codes. For plutonium recycle, the concept of uranium and plutonium homogeneous mixture has been adopted, using self-produced plutonium at equilibrium, in order to get minimum neutronic perturbations in the reactor core. The refueling model studied in the reference reactor was the 'out-in' scheme with a constant number of changed fuel elements (approximately 1/3 of the core). Variations in the material requirements were studied considering changes in the installed nuclear capacity of PWR reactors, the capacity factor of these reactors, and the introduction of fast breeders. Recycling plutonium produced inside the system can reach economies of about 5%U 3 O 8 and 6% separative work units if recycle is assumed only after the 5th operation cycle of the thermal reactors. The cumulative amount of fissile plutonium obtained by the Brazilian Nuclear Program of PWR reactors by 1991 should be sufficient for a fast breeder with the same capacity as Angra 2. For the proposed fast breeder programs, the fissile plutonium produced by thermal reactors is sufficient to supply fast breeder initial necessities. Howewer, U 3 O 8 and SWU economy with recycle is not significant when the proposed fast breeder program is considered. (Author) [pt

Work surface for soluble plutonium

International Nuclear Information System (INIS)

Silver, G.L.

2005-01-01

A three-dimensional work surface for aqueous plutonium is illustrated. It is constructed by means of estimating work as a function of the ambient pH and redox potential in a plutonium solution. The surface is useful for illustrating the chemistry of disproportionation reactions. Work expressions are easier to use than work integrals. (author)

Oxidation-state maxima in plutonium chemistry

International Nuclear Information System (INIS)

Silver, G.L.

2013-01-01

Maxima in the fractions of the trivalent and hexavalent oxidation states of plutonium are inherent in the algebra of its disproportionation reactions. The maxima do not support overall disproportionation equations as satisfactory representations of aqueous plutonium. (author)

Plutonium recycling and the problem of nuclear proliferation

International Nuclear Information System (INIS)

Albright, D.; Feiveson, H.S.

1988-01-01

A typical 1-gigawatt light water reactor (LWR), the dominant commercial power reactor type today, operating at 70% capacity factor, generates approximately 250 kilograms of plutonium annually. This plutonium, which is produced in the reactor through neutron capture by uranium-238, is then discharged from the reactor along with the other constituents of the spent fuel. About 70% of the plutonium, or 175 kilograms, consists of fissile (odd-numbered) plutonium isotopes. As long as the plutonium discharged from the reactor is left intermixed with the highly radioactive fission products also contained in the spent fuel, it cannot readily be used for power or for weapons. However, upon chemical separation from the radioactive fission products and other components of the spent reactor fuel, the plutonium produced each year in a gigawatt reactor could be used, either in recycled fuel (to replace about 175 kilograms of U-235 in a power reactor) or to provide the fissile material for more than 25 nuclear warheads. Commercial separation of plutonium and the introduction of nuclear fuel cycles using recycled plutonium, which are now impending in several countries, force one to balance the probable increased risks of nuclear proliferation due to these activities against various economic and other motives that have been forwarded in their defense. The authors undertake an assessment of this balancing in this article

The use of plutonium rapides surregenerateurs aspects techniques et economiques

International Nuclear Information System (INIS)

Guillet, H.; Delayre, R.; Mougniot, J.C.; Ferrari, A.

1977-01-01

Nuclear energy production utilizing U 235 and U 238 inevitably results in the formation of plutonium. Some of this is directly used by the reactor in power production. Some reactors, e.g. the Candu type, burn most of their plutonium ''in situ''. However the surplus quantity of plutonium produced is increasing, and by 1990 the world stock of plutonium is predicted to be about 1000 tons (300 tons in Europe and 400 in the USA). This represents approximately 0.1 Q of potential power, where Q=10 21 joules. Proposals for dealing with this plutonium include its storage, either as irradiated fuel or as a refined substance (plutonium nitrate or oxide); its use in thermal reactors as a substitute for U 235 ; its use in fast breeder reactors which can act as consumers of plutonium as well as producers and which can therefore regulate the world's plutonium stocks. Leaving aside the question of storage, certain technical conditions must be fulfilled. It is essential that reprocessing plants should be operational and available in adequate numbers. An industry able to make use of plutonium should be developed with large capacity units. There seem to be no problems with plutonium use in reactors: conclusive experiments have proved the accuracy of calculations regarding plutonium recycling in thermal reactors and a number of fast breeders have proved the possibility of using plutonium in them. Experience acquired during the past ten years permits us to deal with the safety and safeguards problem of using plutonium. Many economic questions remain, however, including questions affecting the utilization of plutonium, such as the cost of regenerating irradiated fuel and of making fuel, and questions affecting the strategy of using plutonium in different ways, such as the price at which it should be sold. Also the cost of producing electricity using plutonium is not yet clear. It is unavoidable that plutonium will be used in nuclear power development. The technical and economic problems

Plutonium Finishing Plant safety evaluation report

International Nuclear Information System (INIS)

1995-01-01

The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE's independent review and evaluation of the PFP FSAR and the basis for approval of the PFP FSAR. The evaluation is presented in a format that parallels the format of the PFP FSAR. As an aid to the reactor, a list of acronyms has been included at the beginning of this report. The DOE review concluded that the risks associated with conducting plutonium handling, processing, and storage operations within PFP facilities, as described in the PFP FSAR, are acceptable, since the accident safety analyses associated with these activities meet the WHC risk acceptance guidelines and DOE safety goals in SEN-35-91

Recommendations for plutonium colloid size determination

International Nuclear Information System (INIS)

Kosiewicz, S.T.

1984-02-01

This report presents recommendations for plutonium colloid size determination and summarizes a literature review, discussions with other researchers, and comments from equipment manufacturers. Four techniques suitable for plutonium colloid size characterization are filtration and ultrafiltration, gel permeation chromatography, diffusion methods, and high-pressure liquid chromatography (conditionally). Our findings include the following: (1) Filtration and ultrafiltration should be the first methods used for plutonium colloid size determination because they can provide the most rapid results with the least complicated experimental arrangement. (2) After expertise has been obtained with filtering, gel permeation chromatography should be incorporated into the colloid size determination program. (3) Diffusion methods can be used next. (4) High-pressure liquid chromatography will be suitable after appropriate columns are available. A plutonium colloid size characterization program with filtration/ultrafiltration and gel permeation chromatography has been initiated

A comparison of single and multiple aliquot TT-OSL data sets for sand-sized quartz from the Arabian Peninsula

International Nuclear Information System (INIS)

Rosenberg, T.M.; Preusser, F.; Wintle, A.G.

2011-01-01

The quartz OSL signal from dune sands from Saudi Arabia and Oman start to saturate at doses of about 100 Gy. In order to try to date dune sands with greater expected doses, a previously published, single-aliquot, regenerative-dose protocol (SAR) for thermally-transferred optically stimulated luminescence (TT-OSL) was tested. Dose recovery tests, recycling and recuperation ratios showed robust functioning and dose response curves demonstrated the potential to extend the dose range to beyond 600 Gy. Multiple aliquot additive dose (MAAD) TT-OSL protocols were used to test for sensitivity changes in the SAR TT-OSL protocol up to doses of 1200 Gy. A strong dose dependent deviation of the SAR TT-OSL relative to the MAAD TT-OSL dose response is observed. Comparison of the TT-OSL and OSL sensitivity data obtained from the MAAD and SAR data sets shows a lack of proportionality between TT-OSL and OSL for the SAR data which will result in a problem when SAR dose response curves are constructed using many regeneration points with doses above 300 Gy.

Analytic determination of plutonium in the environment

International Nuclear Information System (INIS)

Ballada, J.

1967-01-01

The work described in this report was undertaken with a view to determining the plutonium content in the fall-out from nuclear explosions. In the first part are described in turn the importance of the problems due to the plutonium, the physico-chemical properties of the radioelement and the biological dangers which it presents. A detailed and critical analysis is made of the radio-toxicological determination of the plutonium as reported in the literature prior to this report. The second part consists in the presentation of a judicious choice of techniques making it possible to determine plutonium in air, rain-water, soils and ash. After a detailed description of the measurement equipment and the operational techniques which have been developed, a justification of these techniques is given with particular reference to their sensitivity and specificity. After a brief conclusion concerning the preceding chapters, the results are presented. These are then discussed in the ease of each element in which the plutonium has been determined. This discussion is concluded by a consideration of the importance of the occurrence of fall-out plutonium on problems relating to public health. From a consideration of 200 analyses carried out, it is concluded that the contribution of plutonium to the exposure of populations is still very small compared to that of natural radiation and that due to such fission products as strontium 90. The report includes 63 literature references, 26 figures and 11 tables. (author) [fr

The uranium-plutonium breeder reactor fuel cycle

International Nuclear Information System (INIS)

Salmon, A.; Allardice, R.H.

1979-01-01

All power-producing systems have an associated fuel cycle covering the history of the fuel from its source to its eventual sink. Most, if not all, of the processes of extraction, preparation, generation, reprocessing, waste treatment and transportation are involved. With thermal nuclear reactors more than one fuel cycle is possible, however it is probable that the uranium-plutonium fuel cycle will become predominant; in this cycle the fuel is mined, usually enriched, fabricated, used and then reprocessed. The useful components of the fuel, the uranium and the plutonium, are then available for further use, the waste products are treated and disposed of safely. This particular thermal reactor fuel cycle is essential if the fast breeder reactor (FBR) using plutonium as its major fuel is to be used in a power-producing system, because it provides the necessary initial plutonium to get the system started. In this paper the authors only consider the FBR using plutonium as its major fuel, at present it is the type envisaged in all, current national plans for FBR power systems. The corresponding fuel cycle, the uranium-plutonium breeder reactor fuel cycle, is basically the same as the thermal reactor fuel cycle - the fuel is used and then reprocessed to separate the useful components from the waste products, the useful uranium and plutonium are used again and the waste disposed of safely. However the details of the cycle are significantly different from those of the thermal reactor cycle. (Auth.)

Plutonium peroxide precipitation: review and current research

International Nuclear Information System (INIS)

Hagan, P.G.; Miner, F.J.

1980-01-01

Increasing the HNO 3 concentration decreases the filtration time but increases the plutonium concentration in the filtrate. A compromise was therefore necessary. If a minimum plutonium concentration is required in the filtrate, the acidity could be lowered to 1.9M with an approximate doubling in the filtration time. The H 2 O 2 concentration has little effect on filtration time. However, the higher the H 2 O 2 concentration, the less plutonium lost to the filtrate. Concentrations higher than the 22 moles/mole Pu recommended (at least up to 30 molar which was the highest investigated) would be beneficial if reagent costs are not excessive and production capacity exists for destroying the excess H 2 O 2 in the filtrate. Although the effect is not large, filtration time is shorter and the plutonium concentration in the filtrate is lower if metallic impurities are present. The slowest rate of H 2 O 2 addition investigated gives a plutonium peroxide precipitate with the fastest filtration time. The rate of addition has very little effect on the plutonium concentration in the filtrate. The temperature has little effect on the filtration time. 14 0 C is recommended since decomposition of H 2 O 2 would be slower at 14 0 C than at 22 0 C (min. Pu content in the filtrate). The effect of digestion time on both the filtration time and the plutonium content in the filtrate is minor, so the shortest digestion time investigated is recommended

Fluorescent determination of neptunium in plutonium

International Nuclear Information System (INIS)

Alexandruk, V.M.; Babaev, A.S.; Dem'yanova, T.A.; Stepanov, A.V.

1991-01-01

This paper describes a new procedure for direct determination of Neptunium in Plutonium using laser induced time resolved fluorescence method. The procedure based on measurement of fluorescence intensity of Neptunium followed its concentration in effective layer of pellet of calcium fluoride. Detection limit of determination of Neptunium is 2 10 -12 g. At the level of Neptunium content in Plutonium more than 5 ppm relative standard deviation is equal 0.08-0.12. For carrying out of single measurement it is necessary neither more nor less 5 mkg Plutonium

Plutonium Immobilization Can Loading Conceptual Design

Energy Technology Data Exchange (ETDEWEB)

Kriikku, E.

1999-05-13

'The Plutonium Immobilization Facility will encapsulate plutonium in ceramic pucks and seal the pucks inside welded cans. Remote equipment will place these cans in magazines and the magazines in a Defense Waste Processing Facility (DWPF) canister. The DWPF will fill the canister with glass for permanent storage. This report discusses the Plutonium Immobilization can loading conceptual design and includes a process block diagram, process description, preliminary equipment specifications, and several can loading issues. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.'

Plutonium Immobilization Can Loading Conceptual Design

International Nuclear Information System (INIS)

Kriikku, E.

1999-01-01

'The Plutonium Immobilization Facility will encapsulate plutonium in ceramic pucks and seal the pucks inside welded cans. Remote equipment will place these cans in magazines and the magazines in a Defense Waste Processing Facility (DWPF) canister. The DWPF will fill the canister with glass for permanent storage. This report discusses the Plutonium Immobilization can loading conceptual design and includes a process block diagram, process description, preliminary equipment specifications, and several can loading issues. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.'

New developments in the air transport of plutonium

International Nuclear Information System (INIS)

Andersen, J.A.

1978-01-01

A new package for the air transport of plutonium has been developed in response to a United States Public Law which restricts the US air transport of plutonium except for small medical devices. This new package, called PAT-1 for plutonium air transportable package model 1, is the result of the NRC-sponsored PARC (plutonium accident resistant container) project at Sandia Laboratories, Albuquerque. The PAT-1 package is designed to meet or exceed new criteria specified in NUREG-0360. These include a severe test sequence of impact (greater than 250 KTS) on an unyielding target, crush, puncture, slash, a large JP-4 fire for 1 hour, followed by water immersion, with stringent acceptance standards on plutonium release, nuclear shielding, and nuclear criticality. The PAT-1 package design features a high energy absorption capability with high-level fire protection. It weighs approximately 227 kg (500 lb) when loaded with 2 kg PuO 2 , and can accommodate up to 25 watts thermal energy from the plutonium load

The calculation of annual limits of intake for plutonium-239 in man using a bone model which allows for plutonium burial and recycling

International Nuclear Information System (INIS)

Priest, N.D.; Hunt, B.W.

1979-01-01

Values of the annual limit intake (ALI) for plutonium-239 in man have been calculated using committed dose equivalent limits as recommended by ICRP in Publication 26. The calculations were made using a multicompartment bone model which allows for plutonium burial and recycling in the skeleton. In one skeletal compartment, the growing surfaces of cortical bone, it is assumed that plutonium deposits are retained and are not subject to resorption or recycling. In the trabecular bone compartment plutonium is taken to be resorbed with either subsequent redeposition onto bone surfaces or retention in the bone marrow. ALIs for plutonium-239 have been calculated assuming a range of rates of bone accretion (0 to 32 μm yr -1 ), different amounts of plutonium retained in the marrow (0 to 60%) and a 20%, 45% or 70% deposition of plutonium in the skeleton from the blood. The calculations made using this bone model suggest that 750 Bq (20 nCi) is an appropriate ALI for the inhalation of class W and class Y plutonium compounds and that 830 kBq and 5 MBq (23 μCi and 136 μCi) are the appropriate ALIs for the ingestion of soluble and insoluble forms of plutonium respectively. (author)

The calculation of annual limits of intake for plutonium-239 in man using a bone model which allows for plutonium burial and recycling.

Science.gov (United States)

Priest, N D; Hunt, B W

1979-05-01

Values of the annual limit of intake (ALI) for plutonium-239 in man have been calculated using committed dose equivalent limits as recommended by ICRP in Publication 26. The calculations were made using a multicompartment bone model which allows for plutonium burial and recycling in the skeleton. In one skeletal compartment, the growing surfaces of cortical bone, it is assumed that plutonium deposits are retained and are not subject to resorption or recycling. In the trabecular bone compartment plutonium is taken to be resorbed with either subsequent redeposition onto bone surfaces or retention in the bone marrow. ALIs for plutonium-239 have been calculated assuming a range of rates of bone accretion (0-32 micron yr-1), different amounts of plutonium retained in the marrow (0-60%) and a 20%, 45% or 70% deposition of plutonium in the skeleton from the blood. The calculations made using this bone model suggest that 750 Bq (20 nCi) is an appropriate ALI for the inhalation of class W and class Y plutonium compounds and that 830 kBq and 5 MBq (23 muCi and 136 muCi) are the appropriate ALIs for the ingestion of soluble and insoluble forms of plutonium respectively.

Utility of a Multiplex PCR Assay for Detecting Herpesvirus DNA in Clinical Samples

Science.gov (United States)

Druce, Julian; Catton, Mike; Chibo, Doris; Minerds, Kirsty; Tyssen, David; Kostecki, Renata; Maskill, Bill; Leong-Shaw, Wendy; Gerrard, Marie; Birch, Chris

2002-01-01

A multiplex PCR was designed to amplify herpes simplex virus types 1 and 2, cytomegalovirus, and varicella-zoster virus DNA present in a diverse range of clinical material. The susceptibility of these viruses to in vivo inhibition by at least one antiviral drug was an important consideration in their inclusion in the multiplex detection system. An aliquot of equine herpesvirus was introduced into each specimen prior to extraction and served as an indicator of potential inhibitors of the PCR and a detector of suboptimal PCR conditions. Compared to virus isolation and immunofluorescence-based antigen detection, the multiplex assay yielded higher detection rates for all viruses represented in the assay. The turnaround time for performance of the assay was markedly reduced compared to those for the other techniques used to identify these viruses. More than 21,000 tests have been performed using the assay. Overall, the multiplex PCR enabled the detection of substantially increased numbers of herpesviruses, in some cases in specimens or anatomical sites where previously they were rarely if ever identified using traditional detection methods. PMID:11980951

Contamination of living environment and human organism with plutonium

International Nuclear Information System (INIS)

Benes, J.

1981-01-01

The applicability of 239 Pu in nuclear power is discussed. The radiotoxic properties of plutonium, its tissue distribution and the effects of internal and external contamination are described. The contamination of the atmosphere, water, and soil with plutonium isotopes is discussed. Dosimetry is described of plutonium in the living and working environments as is plutonium determination in the human organism. (H.S.)

Plutonium Chemistry in the UREX+ Separation Processes

Energy Technology Data Exchange (ETDEWEB)

ALena Paulenova; George F. Vandegrift, III; Kenneth R. Czerwinski

2009-10-01

The project "Plutonium Chemistry in the UREX+ Separation Processes” is led by Dr. Alena Paulenova of Oregon State University under collaboration with Dr. George Vandegrift of ANL and Dr. Ken Czerwinski of the University of Nevada at Las Vegas. The objective of the project is to examine the chemical speciation of plutonium in UREX+ (uranium/tributylphosphate) extraction processes for advanced fuel technology. Researchers will analyze the change in speciation using existing thermodynamics and kinetic computer codes to examine the speciation of plutonium in aqueous and organic phases. They will examine the different oxidation states of plutonium to find the relative distribution between the aqueous and organic phases under various conditions such as different concentrations of nitric acid, total nitrates, or actinide ions. They will also utilize techniques such as X-ray absorbance spectroscopy and small-angle neutron scattering for determining plutonium and uranium speciation in all separation stages. The project started in April 2005 and is scheduled for completion in March 2008.

Constitutional problems in the handling of plutonium

International Nuclear Information System (INIS)

Witt, S. de.

1989-01-01

Reprocessing and final storage involve two different systems of nuclear energy utilization: with or without the use of plutonium. There is a choice available between these two systems. The paper discusss the constitutional implications of this choice. The permission of the use of plutonium as nuclear fuel by the Atomic Energy Law is irreconcilable with the Basic Law, i.e. the Constitution. If the corresponding provisions of the Atomic Energy Law are repealed, then only the plutonium-related branch will be revoked and not the legal permission of nuclear energy as a whole. The fact is not ignored that the Atomic Energy law does not permit the construction and operation of a plant or the handling of plutonium if this were to violate a basic right. However, the plutonium-related branch of nculear energy utilization inevitably results in such basic right violations; hence the Atomic Energy law is unconstitutional in this respect. (orig./HSCH) [de

Assessment of PWR plutonium burners for nuclear energy centers

International Nuclear Information System (INIS)

Frankel, A.J.; Shapiro, N.L.

1976-06-01

The purpose of the study was to explore the performance and safety characteristics of PWR plutonium burners, to identify modifications to current PWR designs to enhance plutonium utilization, to study the problems of deploying plutonium burners at Nuclear Energy Centers, and to assess current industrial capability of the design and licensing of such reactors. A plutonium burner is defined to be a reactor which utilizes plutonium as the sole fissile addition to the natural or depleted uranium which comprises the greater part of the fuel mass. The results of the study and the design analyses performed during the development of C-E's System 80 plant indicate that the use of suitably designed plutonium burners at Nuclear Energy Centers is technically feasible

Biological behaviour of plutonium inhaled by baboons as plutonium n-tributylphosphate complex. Comparison with ICRP models

International Nuclear Information System (INIS)

Metivier, H.; Duserre, C.; Rateau, G.; Legendre, N.; Masse, R.; Piechowski, J.; Menoux, B.

1989-01-01