Dinuclear Cu(II) complexes of isomeric bis-(3-acetylacetonate)benzene ligands: synthesis, structure, and magnetic properties.

Science.gov (United States)

Rancan, Marzio; Dolmella, Alessandro; Seraglia, Roberta; Orlandi, Simonetta; Quici, Silvio; Sorace, Lorenzo; Gatteschi, Dante; Armelao, Lidia

2012-05-07

Highly versatile coordinating ligands are designed and synthesized with two β-diketonate groups linked at the carbon 3 through a phenyl ring. The rigid aromatic spacer is introduced in the molecules to orient the two acetylacetone units along different angles and coordination vectors. The resulting para, meta, and ortho bis-(3-acetylacetonate)benzene ligands show efficient chelating properties toward Cu(II) ions. In the presence of 2,2'-bipyridine, they promptly react and yield three dimers, 1, 2, and 3, with the bis-acetylacetonate unit in bridging position between two metal centers. X-ray single crystal diffraction shows that the compounds form supramolecular chains in the solid state because of intermolecular interactions. Each of the dinuclear complexes shows a magnetic behavior which is determined by the combination of structural parameters and spin polarization effects. Notably, the para derivative (1) displays a moderate antiferromagnetic coupling (J = -3.3 cm(-1)) along a remarkably long Cu···Cu distance (12.30 Å).

Applicability of light sources and the inner filter effect in UV/acetylacetone and UV/H{sub 2}O{sub 2} processes

Energy Technology Data Exchange (ETDEWEB)

Wu, Bingdang; Yang, Minghui [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing, 210023 (China); Yin, Ran [Department of Civil and Environmental Engineering, The Hong Kong University of Science and Technology, Clear Water Bay, Kowloon (Hong Kong); Zhang, Shujuan, E-mail: sjzhang@nju.edu.cn [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Nanjing, 210023 (China)

2017-08-05

Highlights: • Acetylacetone (AA) could directly use solar irradiation to decolorize dyes. • AA had a wider applicability than H{sub 2}O{sub 2} to a variety of light sources. • The photonic efficiency in the UV/AA process was target-dependent. • An accurate calculation approach for the inner filter effect was developed. - Abstract: Light source is a crucial factor in the application of a photochemical process, which determines the energy efficiency. The performances of acetylacetone (AA) in conversion of aqueous contaminants under irradiation with a low-pressure mercury lamp, a medium-pressure mercury lamp, a xenon lamp, and natural sunlight were investigated and compared with those of H{sub 2}O{sub 2} as reference. In all cases, AA was superior to H{sub 2}O{sub 2} in the degradation of Acid Orange 7. Using combinations of the different light sources with various cut-off and band-pass filters, the spectra responses of the absorbed photons in the UV/AA and UV/H{sub 2}O{sub 2} processes were determined for two colored and two colorless compounds. The photonic efficiency (φ) of the two photochemical processes was found to be target-dependent. A calculation approach for the inner filter effect was developed by taking the obtained φ into account, which provides a more accurate indication of the reaction mechanisms.

Electronic structure of binuclear acetylacetonates of boron difluoride

Science.gov (United States)

Tikhonov, Sergey A.; Svistunova, Irina V.; Samoilov, Ilya S.; Osmushko, Ivan S.; Borisenko, Aleksandr V.; Vovna, Vitaliy I.

2018-05-01

The electronic structure of boron difluoride acetylacetonate and its three derivatives was studied using photoelectron and absorption spectroscopy, as well as the density functional theory. In a series of binuclear acetylacetonate complexes containing bridge-moieties of sulfur and selenium atoms, it was found an appreciable mixing of the π3-orbital of the chelate cycle with atomic orbitals S 3p and Se 4p resulting in destabilization of the HOMO levels by 0.4-0.6 eV, in comparison with the monomer. The positively charged fragment C(CH3)-CX-C(CH3) causes the field effect, which leads to stabilization of the LUMO levels by 0.3-0.4 eV and C 1s-levels by 0.5-1.2 eV. An analysis of the research results on the electronic structure made it possible to determine the effect of substituents in the γ position on the absorption spectra, which is mainly determined by the electron density transfer from the chalcogen atoms to the chelate cycles. It is shown that the calculated energy intervals between electron levels correlate well with the structure of the photoelectron spectra of valence and core electrons.

The Effect of Precursor Ligands and Oxidation State in the Synthesis of Bimetallic Nano-Alloys

KAUST Repository

LaGrow, Alec P.

2015-05-12

The characteristics of bimetallic nanomaterials are dictated by their size, shape and elemental distribution. Solution synthesis is widely utilized to form nanomaterials, such as nanoparticles, with controlled size and shape. However, the effects of variables on the characteristics of bimetallic nanomaterials are not completely understood. In this study, we used a continuous-flow synthetic strategy to explore the effects of the ligands and the oxidation state of a metal precursor in a shape-controlled synthesis on the final shape of the nanomaterials and the elemental distribution within the alloy. We demonstrate that this strategy can tune the size of monodisperse PtM (M=Ni or Cu) alloy nanocrystals ranging from 3 to 16 nm with an octahedral shape using acetylacetonate or halide precursors of Pt(II), Pt(IV) and Ni or Cu (II). The nanoparticles formed from halide precursors showed an enrichment of platinum on their surfaces, and the bromides could oxidatively etch the nanoparticles during synthesis with the O2/Br- pair. The two nanocrystal precursors can be uti-lized independently and can control the size with a trend of Pt(acac)222222 for the secondary metal (copper or nickel). These results open up avenues to understand the effect of the ligand shell of a precursor during the synthesis of alloy nanoparticles as well as to control, in a scalable manner, the nanomaterial size and surface chemistry.

Clinical applications of indium-111-acetylacetone-labelled blood cells

International Nuclear Information System (INIS)

Georgi, P.; Sinn, H.; Wellman, H.; Clorius, J.H.; Becker, W.

1981-01-01

A method permitting red-cell labelling with 111 In-acetylacetone was reported in 1974 for evaluating intestinal blood loss, the liver-spleen ratio and the red-cell volume. White blood cells can be tagged similarly. In white-cell labelling, simultaneous red-cell or platelet tagging is avoided. Several procedures (dextran separation and gradient centrifugations) have been combined, to develop a highly selective cell separation. In osteomyelitis it may not be as advantageous to use 67 Ga-citrate, as in inflammatory soft tissue processes. The detection of inflammatory processes with labelled leukocytes could be of great importance for the scintigraphic diagnosis of osteomyelitidies. A group of 97 patients with suspected osteomyelitis have been examined using 111 In-acetylacetone-labelled leukocytes ( 111 In-AAL) immediately following positive routine skeletal scintigraphy. Images obtained 24 h post injection usually were the most satisfactory. In the followup group of 70 patients 21 true positives, 43 true negatives, 21 false negatives and 3 false positives were observed. These findings result in a specificity of 92%, sensitivity of 50% and accuracy of 70% with 111 In-AAL for osteomyelitis. Preliminary investigations using 111 In-acetylacetone-labelled thrombocytes ( 111 In-AAT) were carried out to detect rejection of transplanted kidneys. The platelets were separated by means of additional special density gradient centrifugations but no dextran from 15-20 ml of autologous whole blood. Scans have been obtained 15 min, 2.5 h and 24 h post injection in an initial group of 10 patients. In acute rejection, a high transplant uptake has been detected, whereas patients without acute rejection showed no or only a minimum activity accumulation. Patients with chronic rejection have intermediate uptakes

An application of the coincidence Doppler spectroscopy for substances of chemical interest: phthalocyanine and acetylacetonate complexes

International Nuclear Information System (INIS)

Ito, Y.; Suzuki, T.

2000-01-01

Coincidence Doppler spectroscopy, which is particularly powerful when one is concerned with high momentum components of positron annihilation gamma-rays, has been applied to two different kinds of organo-metallic ligands: metal phthalocyanines and metal acetylacetonates. The energy (momentum) profiles of the annihilation gamma-rays were the same for metal phthalocyanines indicating that positron and/or positronium are not interacting with the metal ions. However, the profiles for the metal acetylacetonates evidently showed a dependence on the kind of metal ions. Discussion is made on the features of positron interaction which are different for phthalocyanines and acetylacetonates.

On the role of the ground state Tb(3)/acetylacetone complex in sensitized emission of Tb(3) in ethanol solution

International Nuclear Information System (INIS)

Lis, S.; Elbanowski, M.; Marciniak, B.

1989-01-01

The Tb(3)-acetylacetone system in ethanol solution has been studied by spectroscopic methods. The formation of a Tb(3)/acetylacetone (1:1) complex in the ground state has been proved and its stability constant determined, K = (0,97 ± 0,06).10 4 dm 3 mol -1 . The role of this complex in the spectrofluorimetric determination of Ln(3) ions in the presence of acetylacetone has been discussed. (Authors)

Zinc acetylacetonate hydrate adducted with nitrogen donor ligands: Synthesis, spectroscopic characterization, and thermal analysis

Science.gov (United States)

Brahma, Sanjaya; Shivashankar, S. A.

2015-12-01

We report synthesis, spectroscopic characterization, and thermal analysis of zinc acetylacetonate complex adducted by nitrogen donor ligands, such as pyridine, bipyridine, and phenanthroline. The pyridine adducted complex crystallizes to monoclinic crystal structure, whereas other two adducted complexes have orthorhombic structure. Addition of nitrogen donor ligands enhances the thermal property of these complexes as that with parent metal-organic complex. Zinc acetylacetonate adducted with pyridine shows much higher volatility (106 °C), decomposition temperature (202 °C) as that with zinc acetylacetonate (136 °C, 220 °C), and other adducted complexes. All the adducted complexes are thermally stable, highly volatile and are considered to be suitable precursors for metal organic chemical vapor deposition. The formation of these complexes is confirmed by powder X-ray diffraction, Fourier transform infrared spectroscopy, mass spectroscopy, and elemental analysis. The complexes are widely used as starting precursor materials for the synthesis of ZnO nanostructures by microwave irradiation assisted coating process.

Assignment of solid-state 13C and 1H NMR spectra of paramagnetic Ni(II) acetylacetonate complexes aided by first-principles computations

DEFF Research Database (Denmark)

Rouf, Syed Awais; Jakobsen, Vibe Boel; Mareš, Jiří

2017-01-01

Recent advances in computational methodology allowed for first-principles calculations of the nuclear shielding tensor for a series of paramagnetic nickel(II) acetylacetonate complexes, [Ni(acac)2L2] with L = H2O, D2O, NH3, ND3, and PMe2Ph have provided detailed insight into the origin of the par......Recent advances in computational methodology allowed for first-principles calculations of the nuclear shielding tensor for a series of paramagnetic nickel(II) acetylacetonate complexes, [Ni(acac)2L2] with L = H2O, D2O, NH3, ND3, and PMe2Ph have provided detailed insight into the origin...

Preparation of ferric acetylacetonate, bonzonate and caprate labelled with Fe-55 and tests of application to liquid scintillation measurements

International Nuclear Information System (INIS)

Los Arcos, J.M.; Rodriguez Barquero, L.; Grau Malonda, A.

1990-01-01

The methods of preparation of ferric acetylacetonate, benzoate and caprate labelled with 55 Fe are described. The quenching effect, the spectral baehaviour and the count rate stability are studied by liquid scintillation measurements in toluene, INSTAGEL and HISAFE II, for two different values of the sample concentration. The ferric acetylaceton-ate is stable for all the three scintillators but shows a strong quench, while the ferric benzoate and caprate are stable only for INSTAGEL and HISAFE II showing no significant quench at the concentrat-ions of interest in habitual measurements. (Author)

Comparison of 111In-oxine and 111In-acetylacetone for the labeling of cells: in vivo and in vitro biological testing

International Nuclear Information System (INIS)

Mathias, C.J.; Heaton, W.A.; Welch, M.J.

1981-01-01

Several complexes of indium were compared as cell labels: indium-111-acetylacetone, indium-111-oxine, and indium-111-chloride complexed with 8-hydroxyquinoline (oxine) immediately prior to use. In labeling with acetylacetone, it was shown that the labeling efficiency is directly proportional to the amount of acetylacetone present, but the cell viability (as measured by in vitro aggregation studies), is inversely proportional to the amount of acetylacetone present. Biological studies were carried out in dogs using indium-111-labeled platelets; survival times and recovery values obtained with platelets labeled using all three techniques were similar. The same solutions were also used to label white blood cells; labeling efficiencies of greater than 80% were obtained in all cases, and the viability (as measured by trypan blue exclusion) was high in all cases. Chemotactic ability of the white cells labeled with indium-111-oxine is higher than that of unlabeled control cells; however, cells labeled with indium-111-acetylacetone were the same as the unlabeled control cells. (author)

Solvent extraction of platinum with thiobenzanilide. Separation of platinum from copper

International Nuclear Information System (INIS)

Shkil', A.N.; Zolotov, Yu.A.

1989-01-01

The solvent extraction of micro concentrations of platinum has been investigated from hydrochloric acid media using thiobenzanilide in the presence of SnCl 2 and KI. In the presence of SnCl 2 platinum is extracted rapidly and to significant completion. Conditions have been developed for the quantitative extraction of platinum. The authors have also examined the solvent extraction of copper(II) using thiobenzanilide, interference due to copper(II) and iron(III) on solvent extraction of platinum, and methods to suppress this interference. A procedure has also been developed for the separation of platinum from copper. Solvent extraction of metals was studied using radioactive isotopes: 197 Pt, 64 Cu, 59 Fe, 198 Au, 109 Pd, 110m Ag

Simple one-pot synthesis of platinum-palladium nanoflowers with enhanced catalytic activity and methanol-tolerance for oxygen reduction in acid media

International Nuclear Information System (INIS)

Zheng, Jie-Ning; He, Li-Li; Chen, Fang-Yi; Wang, Ai-Jun; Xue, Meng-Wei; Feng, Jiu-Ju

2014-01-01

Graphical abstract: PtPd nanoflowers were fabricated by one-pot solvothermal co-reduction method in oleylamine system, which exhibited the improved electrocatalytic activity and higher methanol tolerance for oxygen reduction, compared with commercial Pt and Pd black catalysts. - Highlights: • Bimetallic alloyed PtPd nanoflowers are prepared by a simple one-pot solvothermal co-reduction method. • PtPd nanoflowers display high catalytic performance for ORR dominated by a four-electron pathway. • PtPd nanoflowers show good methanol tolerance for ORR. - Abstract: In this work, bimetallic alloyed platinum-palladium (PtPd) nanoflowers are fabricated by one-pot solvothermal co-reduction of Pt (II) acetylacetonate and Pd (II) acetylacetonate in oleylamine system. The as-prepared nanostructures show the enhanced electrocatalytic activity for oxygen reduction reaction (ORR), dominated by a four-electron pathway based on the Koutecky-Levich plots, mainly owing to the inhibition of the formation of Pt–OH ad via the downshift of d-band center for Pt. Meanwhile, PtPd nanoflowers display good methanol tolerance and improved stability for ORR. The chronoamperometry test reveals that the current of PtPd nanoflowers remains 45.9% of its original value within 6000 s, much higher than those of commercial Pt (36.7%) and Pd (32.2%) black catalysts. Therefore, PtPd nanoflowers with unique interconnected structures can be used as a promising cathode catalyst in direct methanol fuel cells

One step synthesis of chlorine-free Pt/Nitrogen-doped graphene composite for oxygen reduction reaction

KAUST Repository

Varga, Tamá s; Varga, Á gnes Tí mea; Ballai, Gergő; Haspel, Henrik; Kukovecz, Á kos; Kó nya, Z.

2018-01-01

Chlorine-free Platinum/nitrogen-doped graphene oxygen reduction reaction catalysts were synthesized by a one step method of annealing a mixture of platinum acetylacetonate and graphene oxide under ammonia atmosphere. Nanoparticles with close

Mono(p-tolyl)platinum(II) and bis(p-tolyl)platinum(II) complexes of diethylsulfide as reagents for organoplatinum synthesis. Structures of [Pt(p-Tol)2(µ-SEt2)]2 and PtCl(p-Tol)(bpy) (bpy = 2,2'-bipyridine)

NARCIS (Netherlands)

Koten, G. van; Casado Lacabra, M.A.; Canty, A.J.; Lutz, M.H.; Patel, J.; Spek, A.L.; Sun, H.

2001-01-01

The complex trans-PtCl(p-Tol)(SEt{2}){2} is obtained from the reaction of [Pt(p-Tol){2}(SEt{2})]{2} with PtCl{2}(SEt{2}){2} and SEt{2} in mole ratio 1:2:2. The mono(p-tolyl)platinum(II) and bis(p-tolyl)platinum(II) complexes of diethylsulfide react with 2, 2'-bipyridine to form the complexes

Saturated vapor pressure of lutetium tris-acetylacetonate

Energy Technology Data Exchange (ETDEWEB)

Trembovetskij, G.V.; Berdonosov, S.S.; Murav' eva, I.A.; Martynenko, L.I. (Moskovskij Gosudarstvennyj Univ. (USSR))

1983-12-01

By the statical method using /sup 177/Lu radioactive isotope the saturated vapor pressure of anhydrous lutetium acetylacetonate at 130 to 160 deg is determined. The calculations are carried out assuming the vapor to be monomolecular. The equation of lgP versus 1/T takes the form: lg Psub((mmHg))=(8.7+-1.6)-(4110+-690)/T. The thermodynamical characteristics of LuA/sub 3/ sublimation are calculated to be ..delta..Hsub(subl.)=79+-13 kJ/mol; ..delta..Ssub(subl.)=111+-20 J/kxmol.

Influence of post-deposition annealing on structural, morphological and optical properties of copper (II) acetylacetonate thin films.

Science.gov (United States)

Abdel-Khalek, H; El-Samahi, M I; El-Mahalawy, Ahmed M

2018-05-21

In this study, the effect of thermal annealing under vacuum conditions on structural, morphological and optical properties of thermally evaporated copper (II) acetylacetonate, cu(acac) 2 , thin films were investigated. The copper (II) acetylacetonate thin films were deposited using thermal evaporation technique at vacuum pressure ~1 × 10 -5  mbar. The deposited films were thermally annealed at 323, 373, 423, and 473 K for 2 h in vacuum. The thermogravimetric analysis of cu(acac) 2 powder indicated a thermal stability of cu(acac) 2 up to 423 K. The effects of thermal annealing on the structural properties of cu(acac) 2 were evaluated employing X-ray diffraction method and the analysis showed a polycrystalline nature of the as-deposited and annealed films with a preferred orientation in [1¯01] direction. Fourier transformation infrared (FTIR) technique was used to negate the decomposition of copper (II) acetylacetonate during preparation or/and annealing up to 423 K. The surface morphology of the prepared films was characterized by means of field emission scanning electron microscopy (FESEM). A significant enhancement of the morphological properties of cu(acac) 2 thin films was obtained till the annealing temperature reaches 423 K. The variation of optical constants that estimated from spectrophotometric measurements of the prepared thin films was investigated as a function of annealing temperature. The annealing process presented significantly impacted the nonlinear optical properties such as third-order optical susceptibility χ (3) and nonlinear refractive index n 2 of cu(acac) 2 thin films. Copyright © 2018 Elsevier B.V. All rights reserved.

Influence of acetylacetonates of 3d-metals on the γ radiolysis of benzene

International Nuclear Information System (INIS)

Zatonskii, S.V.; Makhlyarchuk, V.V.; Morozova, L.N.

1986-01-01

This paper investigates the formation of diphenyl and phenylcyclohexadiene in the radiolysis of benzene in the presence of the following acetylacetonates: Cr (AA) 3 , Mn (AA) 2 .2H 2 O, Mn (AA) 3 , Fe (AA) 2 .2H 2 O, Fe (AA) 3 , Co (AA) 3 . It was found that bisacetylacetonatocobalt (II) lowers the radiation chemical yields of the dimers to a substantial degree. It was suggested that the effect is caused by a reaction of addition of free radicals, arising under the action of radiation, to the central ion of the chelate

Physico-chemical characterization of mixed-ligand complexes of Mn(III based on the acetylacetonate and maleic acid and its hydroxylamine derivative

Directory of Open Access Journals (Sweden)

Cakić Suzana M.

2005-01-01

Full Text Available Two new Mn(III mixed-ligand complexes with two acetylacetonate (acac ligands and one maleate ligand and its hydroxylamine derivative of the general formula [Mn(C5H7O22L] were prepared. Their structure was established by using elemental analysis, FTIR and UV/VIS spectroscopic methods, as well as magnetic measurement. Replacement of the acetylacetonate ligand by the corresponding acid ligand has been confirmed in Mn(III acetylacetonate. Based on the obtained experimental data and literature indications, structural formulae to these compounds were assigned.

Yb3+ can be much better than Dy3+: SMM properties and controllable self-assembly of novel lanthanide 3,5-dinitrobenzoate-acetylacetonate complexes.

Science.gov (United States)

Gavrikov, Andrey V; Efimov, Nikolay N; Ilyukhin, Andrey B; Dobrokhotova, Zhanna V; Novotortsev, Vladimir M

2018-05-01

The first representatives of the binuclear lanthanide 3,5-dinitrobenzoate-acetylacetonate complexes, namely isostructural compounds [Ln(dnbz)(acac)2(H2O)(EtOH)]2 (Ln = Eu (1), Gd (2), Tb (3), Dy (4), Ho (5), Er (6), Tm (7), and Yb (8); dnbz - 3,5-dinitrobenzoate anion; acac - acetylacetonate (pentane-2,4-dionate) anion) were prepared and characterized. The SMM behavior of the Yb compound 8 was shown to be surprisingly less sensitive to the composition of the Yb3+ coordination environment in comparison with that of the Dy derivative. For Yb compound 8, the anisotropy barrier is Δeff/kB = 26 K under the dc field of 2000 Oe. This value is the highest one currently known for binuclear Yb complexes.

Investigations of the conditions of obtaining and of purifying zirconium acetylacetonate

International Nuclear Information System (INIS)

Dobrowolski, J.; Kozera, F.; Hubicki, Z.

1980-01-01

The method of obtaining zirconium acetylacetonate with a yield of 90% has been elaborated and there has been presented the way of removing the impurities of Fe, Ti, Cl, N and Hf. The conditions of transforming the hydrated compound into an anhydrous one without using large quantities of anhydrous solvents have been determined. (author)

Platinum metals in the environment

Energy Technology Data Exchange (ETDEWEB)

Zereini, Fathi [Frankfurt Univ. (Germany). Dept. of Environmental Analytical Chemistry; Wiseman, Clare L.S. (ed.) [Toronto Univ. (Canada). School of the Environment

2015-03-01

This book contains the five chapters with the following topics: 1. SOURCES OF PGE EMISSIONS ELEMENTS: Sources of Platinum Group Elements (PGE) in the Environment; Impact of Platinum Group Element Emissions from Mining and Production Activities. 2. ANALYTICAL METHODS FOR THE DETERMINATION OF PGE IN BIOLOGICAL AND ENVIRONMENTAL MATRICES: Appraisal of Biosorption for Recovery, Separation and Determination of Platinum, Palladium and Rhodium in Environmental Samples; On the Underestimated Factors Influencing the Accuracy of Determination of Pt and Pd by Electrothermal Atomic Absorption Spectrometry in Road Dust Samples; Application of Solid Sorbents for Enrichment and Separation of Platinum Metal Ions; Voltammetric Analysis of Platinum in Environmental Matrices; Speciation Analysis of Chloroplatinates; Analysis of Platinum Group Elements in Environmental Samples: A Review. 3. OCCURRENCE, CHEMICAL BEHAVIOR AND FATE OF PGE IN THE ENVIRONMENT: Brazilian PGE Research Data Survey on Urban and Roadside Soils; Platinum, Palladium and Rhodium in a Bavarian Roadside Soil; Increase of Platinum Group Element Concentrations in Soils and Airborne Dust During the Period of Vehicular Exhaust Catalysts Introduction; Platinum-Group Elements in Urban Fluvial Bed Sediments-Hawaii; Long-Term Monitoring of Palladium and Platinum Contents in Road Dust of the City of Munich, Germany; Characterization of PGEs and Other Elements in Road Dusts and Airborne Particles in Houston, Texas; Accumulation and Distribution of Pt and Pd in Roadside Dust, Soil and Vegetation in Bulgaria; Increase of the Environmental Pt Concentration in the Metropolitan Area of Mexico City Associated to the Use of Automobile Catalytic Converters; Solubility of Emitted Platinum Group Elements (Pt, Pd and Rh) in Airborne Particulate Matter (PM10) in the Presence of Organic Complexing Agents; The Influence of Anionic Species (Cl{sup -}, NO{sub 3}{sup -}, SO{sub 4}{sup 2-}) on the Transformation and Solubility of Platinum in

Extraction of acetylacetonates of some metals from melts of trihydrate lithium nitrate

International Nuclear Information System (INIS)

Sevast'yanov, A.I.; Rudenko, N.P.; Kuznetsov, A.F.; Lanskaya, N.G.

1987-01-01

Extraction of beryllium cobalt and lithium from melts of trihydrate lithium nitrate at 37 deg C using 0.5 mol solutions of acetylacetone in chloroform, tetrachlorethylene and carbon tetrachloride is studied. Beryllium is quantitatively extracted at pH 3.8-5.5, the phase volume ratio being V org :V melt from 1:1 to 1:10. The degree of the beryllium complex unitary extraction from melt depends on the nature of organic solvent and is 100% for CCl 4 , CHCl 3 and 85% for C 2 Cl 4 . Solvents on Be extraction ability are placed in the following series CCl 4 > CHCl 3 >C 2 Cl 4

ESI-MS studies of the reactions of novel platinum(II) complexes containing O,O'-chelated acetylacetonate and sulfur ligands with selected model proteins.

Science.gov (United States)

Marzo, Tiziano; De Pascali, Sandra A; Gabbiani, Chiara; Fanizzi, Francesco P; Messori, Luigi; Pratesi, Alessandro

2017-08-01

A group of mixed-ligand Pt(II) complexes bearing acetylacetonate and sulphur ligands were recently developed in the University of Lecce as a new class of prospective anticancer agents that manifested promising pharma-cological properties in preliminary in vitro and in vivo tests. Though modelled on the basis of cisplatin, these Pt(II) complexes turned out to exhibit a profoundly distinct mode of action as they were found to act mainly on non-genomic targets rather than on DNA. Accordingly, we have explored here their reactions with two representative model proteins through an established ESI-MS procedure with the aim to describe their general interaction mechanism with protein targets. A pronounced reactivity with the tested proteins was indeed documented; the nature of the resulting metallodrug-protein interactions could be characterised in depth in the various cases. Preferential binding to protein targets compared to DNA is supported by independent ICP-OES measurements. The implications of these findings are discussed.

[Pt(O,O’-acac)(γ-acac)(DMS)] Alters SH-SY5Y Cell Migration and Invasion by the Inhibition of Na+/H+ Exchanger Isoform 1 Occurring through a PKC-ε/ERK/mTOR Pathway

Science.gov (United States)

Muscella, Antonella; Vetrugno, Carla; Calabriso, Nadia; Cossa, Luca Giulio; De Pascali, Sandra Angelica; Fanizzi, Francesco Paolo; Marsigliante, Santo

2014-01-01

We previously showed that [Pt(O,O’-acac)(γ-acac)(DMS)] ([Pt(acac)2(DMS)]) exerted substantial cytotoxic effects in SH-SY5Y neuroblastoma cells, and decreased metalloproteases (MMPs) production and cells migration in MCF-7 breast cancer cells. The ubiquitously distributed sodium-hydrogen antiporter 1 (NHE1) is involved in motility and invasion of many solid tumours. The present study focuses on the effects of [Pt(acac)2(DMS)] in SH-SY5Y cell migration and also on the possibility that NHE1 may be involved in such effect. After sublethal [Pt(acac)2(DMS)] treatment cell migration was examined by wounding assay and cell invasion by transwell assay. NHE1 activity was measured in BCECF-loaded SH-SY5Y as the rate of Na+-dependent intracellular pH recovery in response to an acute acid pulse. Gelatin zymography for MMP-2/9 activities, Western blottings of MMPs, MAPKs, mTOR, S6 and PKCs and small interfering RNAs to PKC-ε/-δ mRNA were performed. Sublethal concentrations of [Pt(acac)2(DMS)] decreases NHE1 activity, inhibites cell migration and invasion and decreases expression and activity of MMP-2 and -9. [Pt(acac)2(DMS)] administered to SH-SY5Y cells provokes the increment of ROS, generated by NADPH oxidase, responsible for the PKC-ε and PKC-δ activation. Whilst PKC-δ activates p38/MAPK, responsible for the inhibition of MMP-2 and -9 secretion, PKC-ε activates a pathway made of ERK1/2, mTOR and S6K responsible for the inhibition of NHE1 activity and cell migration. In conclusion, we have shown a drastic impairment in tumour cell metastatization in response to inhibition of NHE1 and MMPs activities by [Pt(acac)2(DMS)] occurring through a novel mechanism mediated by PKC-δ/-ε activation. PMID:25372487

[Pt(O,O'-acac)(γ-acac)(DMS)] alters SH-SY5Y cell migration and invasion by the inhibition of Na+/H+ exchanger isoform 1 occurring through a PKC-ε/ERK/mTOR Pathway.

Science.gov (United States)

Muscella, Antonella; Vetrugno, Carla; Calabriso, Nadia; Cossa, Luca Giulio; De Pascali, Sandra Angelica; Fanizzi, Francesco Paolo; Marsigliante, Santo

2014-01-01

We previously showed that [Pt(O,O'-acac)(γ-acac)(DMS)] ([Pt(acac)2(DMS)]) exerted substantial cytotoxic effects in SH-SY5Y neuroblastoma cells, and decreased metalloproteases (MMPs) production and cells migration in MCF-7 breast cancer cells. The ubiquitously distributed sodium-hydrogen antiporter 1 (NHE1) is involved in motility and invasion of many solid tumours. The present study focuses on the effects of [Pt(acac)2(DMS)] in SH-SY5Y cell migration and also on the possibility that NHE1 may be involved in such effect. After sublethal [Pt(acac)2(DMS)] treatment cell migration was examined by wounding assay and cell invasion by transwell assay. NHE1 activity was measured in BCECF-loaded SH-SY5Y as the rate of Na+-dependent intracellular pH recovery in response to an acute acid pulse. Gelatin zymography for MMP-2/9 activities, Western blottings of MMPs, MAPKs, mTOR, S6 and PKCs and small interfering RNAs to PKC-ε/-δ mRNA were performed. Sublethal concentrations of [Pt(acac)2(DMS)] decreases NHE1 activity, inhibits cell migration and invasion and decreases expression and activity of MMP-2 and -9. [Pt(acac)2(DMS)] administered to SH-SY5Y cells provokes the increment of ROS, generated by NADPH oxidase, responsible for the PKC-ε and PKC-δ activation. Whilst PKC-δ activates p38/MAPK, responsible for the inhibition of MMP-2 and -9 secretion, PKC-ε activates a pathway made of ERK1/2, mTOR and S6K responsible for the inhibition of NHE1 activity and cell migration. In conclusion, we have shown a drastic impairment in tumour cell metastatization in response to inhibition of NHE1 and MMPs activities by [Pt(acac)2(DMS)] occurring through a novel mechanism mediated by PKC-δ/-ε activation.

A New Homogeneous Catalyst for the Dehydrogenation of Dimethylamine Borane Starting with Ruthenium(III Acetylacetonate

Directory of Open Access Journals (Sweden)

Ebru Ünel Barın

2015-06-01

Full Text Available The catalytic activity of ruthenium(III acetylacetonate was investigated for the first time in the dehydrogenation of dimethylamine borane. During catalytic reaction, a new ruthenium(II species is formed in situ from the reduction of ruthenium(III and characterized using UV-Visible, Fourier transform infrared (FTIR, 1H NMR, and mass spectroscopy. The most likely structure suggested for the ruthenium(II species is mer-[Ru(N2Me43(acacH]. Mercury poisoning experiment indicates that the catalytic dehydrogenation of dimethylamine-borane is homogeneous catalysis. The kinetics of the catalytic dehydrogenation of dimethylamine borane starting with Ru(acac3 were studied depending on the catalyst concentration, substrate concentration and temperature. The hydrogen generation was found to be first-order with respect to catalyst concentration and zero-order regarding the substrate concentration. Evaluation of the kinetic data provides the activation parameters for the dehydrogenation reaction: the activation energy Ea = 85 ± 2 kJ·mol−1, the enthalpy of activation ∆H# = 82 ± 2 kJ·mol−1 and the entropy of activation; ∆S# = −85 ± 5 J·mol−1·K−1. The ruthenium(II catalyst formed from the reduction of ruthenium(III acetylacetonate provides 1700 turnovers over 100 hours in hydrogen generation from the dehydrogenation of dimethylamine borane before deactivation at 60 °C.

Adsorption and temperature-programmed desorption of hydrogen with dispersed platinum and platinum-gold catalysts

Energy Technology Data Exchange (ETDEWEB)

Anderson, J.R.; Foger, K.; Breakspere, R.J.

1979-05-01

Adsorption and temperature-programmed desorption of hydrogen with dispersed platinum and platinum-gold catalysts was studied with 0.9-3Vertical Bar3< platinum on silica gel, aerosil, sodium and lanthanum Y zeolites, and ..gamma..-alumina, and on aerosil-supported gold-platinum alloys containing 2, 10, 24, 33, and 85Vertical Bar3< gold. Surface enrichment with gold in the alloy systems, as derived from hydrogen adsorption data and predicted from surface enrichment theory and electron microscopic measurements of particle size, were in good agreement, which indicated that equilibrium was achieved by the thermal treatment (oxygen at 573/sup 0/K, hydrogen at 620/sup 0/K, repeated cycles) used. Hydrogen spillover to gold was observed at the higher hydrogen pressures tested on the alloys with high gold content, and to the zeolite supports. The temperature-programed desorption profiles were independent of gold content, which indicated that gold acts only as diluent, and that isolated surface platinum atoms become populated with hydrogen atoms either by hydrogen atom spillover from platinum ensembles to gold and from the gold to the isolated platinum, and/or by adsorption of a molecule directly on the isolated platinum and chemisorption of one H atom at an adjacent gold atom. The distribution of surface platinum ensembles was evaluated by a computer simulation method.

Mass-spectrometric investigation of rare earth acetylacetonates dipivaloylmethanates and their adducts

International Nuclear Information System (INIS)

Gavrishzhuk, E.M.; Dzyubenko, N.G.; Martynenko, L.I.

1985-01-01

Peculiarities of fragmentation of molecular ions of rare earth acetylacetonates and dipivaloylmethanates under mass-spectrometric investigation of these compounds as well as their adducts with o-phenanthroline, α,α'-dipyridyl, triphenylphosphine oxide are considered in the given review. Similar data for identical derivants of some transitions metals are presented. Data on potentials of appearance and dissociation energy of basic ions in mass-spectra of the studied β-diketonates are analyzed

Synthesis and characterization of platinum(II) complexes with 2,2'-bipyridine derivative supporting ligands.

Science.gov (United States)

Yang, Kwang Woon; Hwang, Hey Eun; Jung, Hee Sun; Kwak, Chee Hun; Lee, Ji Hoon; Jung, Sang-Chul; Ahn, Ho Geun; Chung, Min Chul

2011-08-01

The reaction of the [Pt(bpy-R)Cl2](bpy-R: R=H (2,2'-bipyridine); R=CH3 (4,4'-dimethyl-2,2'-biypridine (DM-bpy), 3,3'-5,5'-tertamethyl-2,2'-bipyridiyl (TM-bpy)) with 1,4-Bis(5'-2',2"-bipyridine)benzene (bpy-Ph-bpy) affords the following mono- and di-platinum complexes of [(bpy)Pt(bpy-Ph-bpy)][PF6]2 (1), [(bpy)Pt(bpy-Ph-bpy)Pt(bpy)])[PF6]4 (2), [(DM-bpy)Pt(bpy-Ph-bpy)])][PF6]2 (3), and [(TM-bpy)Pt(bpy-ph-bpy)[PF6]2 (4), respectively. These complexes were characterized by NMR, IR, UV/VIS, PL and cyclic voltammetry. The internal quantum yields of these platinum(II) complexes are very high (0.83-0.99) and these complexes emit light at deep blue regions (373-417 nm). The redox behavior of complexes 1 and 2 shows quasi-reversible process.

Investigation of zirconium oxychloride interaction with acetylacetone by the method of pH-metric titration

International Nuclear Information System (INIS)

Zharkova, N.Ya.; Martynenko, L.I.; Dzyubenko, N.G.

1989-01-01

Interaction of zirconium oxychloride with acetylacetone (NA) was studied by the method of pH-metric titration using KOH and NH 4 OH as neutralizing agents. It is shown that processes of hydrolysis and complexation complete in the system. It was established that decrease of hydrolysis of Zr-containing complex forms and ZrA 4 · 10H 2 O isolation takes place in relatively concentrated solutions of ZrOCl 2 and NA mixture, taken with 1:4 molar ratio when using NH 4 OH as neutralizing agent

Hydrogenation of hexene over platinum on alumina vs. platinum in a Na-Y zeolite

International Nuclear Information System (INIS)

Miner, R.S. Jr.; Ione, K.G.; Namba, S.; Turkevich, J.

1978-01-01

In order to study the efficacy of zeolites as supports, several platinum H--Y zeolites were prepared by ion exchanging an H--Y zeolite with Pt(NH 3 ) 4 Cl 2 and reducing these products with hydrazine hydrate (A, B, C). Another preparation was made by adsorbing 32-A platinum sol on the zeolite crystallites (D). These catalysts were studied for hydrogenation and isomerization of hexene-1, ethylene hydrogenation, hydrogen chemisorption, and poison titration. They were compared with monodisperse Pt (32 A diameter) on alumina. A marked difference was found between the behavior of hexene-1 with the platinum-in-zeolite and with the platinum-on-alumina

Electrophoretic Deposition of SnO2 Nanoparticles and Its LPG Sensing Characteristics

Directory of Open Access Journals (Sweden)

Göktuğ Günkaya

2015-01-01

Full Text Available Homogenized SnO2 nanoparticles (60 nm in acetylacetone mediums, both with and without iodine, were deposited onto platinum coated alumina substrate and interdigital electrodes using the electrophoretic deposition (EPD method for gas sensor applications. Homogeneous and porous film layers were processed and analyzed at various coating times and voltages. The structure of the deposited films was characterized by a scanning electron microscopy (SEM. The gas sensing properties of the SnO2 films were investigated using liquid petroleum gas (LPG for various lower explosive limits (LEL. The results showed that porous, crack-free, and homogeneous SnO2 films were achieved for 5 and 15 sec at 100 and 150 V EPD parameters using an iodine-free acetylacetone based SnO2 suspension. The optimum sintering for the deposited SnO2 nanoparticles was observed at 500°C for 5 min. The results showed that the sensitivity of the films was increased with the operating temperature. The coated films with EPD demonstrated a better sensitivity for the 20 LEL LPG concentrations at a 450°C operating temperature. The maximum sensitivity of the SnO2 sensors at 450°C to 20 LEL LPG was 30.

Anodic dissolution of samarium in acetonitrile solution of acetylacetone

International Nuclear Information System (INIS)

Kostyuk, N.N.; Dik, T.A.; Trebnikov, A.G.; Shirokij, V.L.

2003-01-01

Electrochemical dissolution of metal samarium in acetonitrile medium in the presence of 0.1 M tetraethylammoniumbromide and 0.9 M acetylacetone (HAA) in argon atmosphere under a voltage of 3 V was considered for studying feasibility of electrochemical synthesis of samarium β-diketonates. Using IR and mass spectrometry, thermal and elementary analyses it was ascertained that, depending on cathode and anode areas ratio, anodic dissolution of samarium can give rise to formation of complexes of bi- and trivalent samarium featuring the composition Sm 4 (AA) 8 · 3HAA, Sm(AA) 3 · HAA and Sm(AA) 3 · 4HAA [ru

Facile synthesis of soluble functional graphene by reduction of graphene oxide via acetylacetone and its adsorption of heavy metal ions

International Nuclear Information System (INIS)

Xu, Minghan; Chai, Jing; Hu, Nantao; Huang, Da; Wang, Yuxi; Huang, Xiaolu; Wei, Hao; Yang, Zhi; Zhang, Yafei

2014-01-01

The synthesis of graphene (GR) from graphene oxide (GO) typically involves harmful chemical reducing agents that are undesirable for most practical applications. Here we report a green and facile synthesis method for the synthesis of GR that is soluble in water and organic solvents and that includes the additional benefit of adsorption of heavy metal ions. Acetylacetone, as both a reducing agent and a stabilizer, was used to prepare soluble GR from GO. Transmission electron microscopy and atomic force microscopy provide clear evidence for the formation of few-layer GR. The results from Fourier transform infrared spectroscopy and ultraviolet-visible spectroscopy show that reduction of GO to GR has occurred. Raman spectroscopy and X-ray photoelectron spectroscopy also indicate the removal of oxygen-containing functional groups from GO, resulting in the formation of GR. The results of dispersion experiments show that GR can be highly dispersed in water and N,N-Dimethylformamide. The reaction mechanism for acetylacetone reduction of exfoliated GO was also proposed. This method is a facile and environmentally friendly approach to the synthesis of GR and opens up new possibilities for preparing GR and GR-based nanomaterials for large-scale applications. Of even greater interest is that inductively coupled plasma atomic emission spectroscopy suggests that synthesized GR may be applied in the absorption of Cd 2+ and Co 2+ due to the strong coordination capacity of acetylacetone on the surfaces and edges of GR and the large surface area of GR in aqueous solutions. The maximum adsorptions are 49.28 mg g −1 for Cd 2+ , which is 4.5 times higher than that of carbon nanotubes, and 27.78 mg g −1 for Co 2+ , which is 3.6 times higher than that of titania beans. (paper)

Formation of TiO/Al2O3/C Composite in Thermal Co-decomposition of Aluminium(III) Acetylacetonate and Titanium(IV) Oxyacetylacetonate.

Czech Academy of Sciences Publication Activity Database

Kovářík, T.; Pokorná, Dana; Urbanová, Markéta; Bezdička, Petr; Bastl, Zdeněk; Kupčík, Jaroslav; Křenek, T.; Pola, M.; Kullová, L.; Pola, Josef

2016-01-01

Roč. 117, JAN 2016 (2016), s. 182-190 ISSN 0165-2370 R&D Projects: GA TA ČR TA04020860 Institutional support: RVO:67985858 ; RVO:61388980 ; RVO:61388955 Keywords : thermal co-decomposition * aluminium(III) acetylacetonate * titanium(IV) oxyacetylacetonate * titanium monoxide * alumina * Carbona Subject RIV: CF - Physical ; Theoretical Chemistry; CA - Inorganic Chemistry (UACH-T) Impact factor: 3.471, year: 2016

Reaction pathways for reduction of nitrate ions on platinum, rhodium, and platinum-rhodium alloy electrodes

International Nuclear Information System (INIS)

Cunha, M.C.P.M. da; De Souza, J.P.I.; Nart, F.C.

2000-01-01

The reduction of nitrate ions on platinum, rhodium, and platinum-rhodium alloy electrodes has been investigated using differential electrochemical mass spectrometry and in situ FTIR measurements. For 3 M HNO 3 concentration it has been found that nitrate starts the reduction with partial N-O bond dissociation and N-N bond formation generating NO and N 2 O. At potentials lower than 0.2 V the reaction proceeds forming dissolved NH 4 + . For potentials lower than 0 V the reduction continues via a multiple pathway reaction leading to the nonselective production of N 2 , NH 2 OH, and N 2 H 2 . On the alloyed electrodes, the production of NO and N 2 O has been observed in both cathodic and anodic scans, while on pure platinum and rhodium electrodes the reaction has been observed only during the cathodic scan. Contrasting with the pure platinum and rhodium alloys, where the N-O bond break starts forming NO and N 2 O, on the alloys HNO 2 has been observed as the first reaction step. For alloys with higher rhodium composition, like Pt 75 Rh 25 , no N 2 has been detected for potentials lower than 0 V

Effect of Ni doping on the structural and magnetic properties of FePt nanoparticles

International Nuclear Information System (INIS)

Yang, H.-W.; Chung, C.-M.; Ding, Jack Y.

2007-01-01

A serial of FePtNi nanoparticles were investigated on their crystal structure and magnetic properties. The FePtNi nanoparticles were synthesized simultaneously by the reduction of iron (III) acetylacetonate, platinum (II) acetylacetonate and nickel (II) acetylacetonate with 1,2-hexadecanediol as the reducing agent. The X-ray diffraction patterns indicate that the addition of 8, 12, 17 at% Ni in FePt nanoparticles suppressed the transformation of the particles from disorder face-centered cubic to order face-centered tetragonal L1 0 -phase under annealing treatment. However, further increasing Ni contents to 21 at%, the nanoparticle transformed to L1 2 phase. Doping of Ni into the FePt compound system may decrease coercivity and crystal anisotropy energy. A maximum coercivity of 7 KOe at room temperature was obtained for (Fe 52 Pt 48 ) 92 Ni 8 nanoparticles after annealing at 600 deg. C for 30 min

Synthesis and Characterization of Platinum(II) Complexes with Various Substituted 2,2'-Bipyridine Ligands.

Science.gov (United States)

Son, Seokhwan; Lee, Hwan Gyu; Lee, Nopl; Ryu, Minwoo; Kwak, Cheenhun; Lee, Jihoon; Ahn, Hogeun; Chung, Minchu

2016-02-01

The reaction of platinum 5,5"-(9,9-dioctyl-9H-fluorene-2,7-diyl)di-2,2'-bipyridine with 2,2'-bipyridine) PtCI2, (1,10-phenanthroline)PtC2 and (2,2'-bipyrimidine)PtC2: (2,2'-bipyridine)Pt[5,5"-(9,9-dioctyl-9H- fluorene-2,7-diyl)di-2,2'-bipyridine] (1) (2,2'-bipyrimi-dine)Pt[5,5"-(9,9-dioctyl-9H-fluorene-2,7-diyl)di- 2,2'-bipyridine] (2) (1,10-Phenantroline)-Pt[5,5"-(9,9-dioctyl-9H-fluorene-2,7-diyl)di-2,2'-bipyridine] (3). In the study, new platinum complex compounds were synthesized utilizing the ligand of a 5,5"-(9,9- dioctyl-9H-fluorene-2,7-diyl)di-2,2'-bipyridine). Each of the three complexes was obtained through the reaction carried out in this study. These complexes were analyzed using 1H(13C)-NMR, PL, and a UV-vis spectrophotometer. The maximum wavelengths of complexes 1, 2, and 3 appear at 519 nm, 375 nm, and 517 nm, respectively. The quantum yields of these complexes are in the range of 0.35-0.67.

Silica functionalized Cu(II) acetylacetonate Schiff base complex: An efficient catalyst for the oxidative condensation reaction of benzyl alcohol with amines

Science.gov (United States)

Anbarasu, G.; Malathy, M.; Karthikeyan, P.; Rajavel, R.

2017-09-01

Silica functionalized Cu(II) acetylacetonate Schiff base complex via the one pot reaction of silica functionalized 3-aminopropyltriethoxysilane with acetyl acetone and copper acetate has been reported. The synthesized material was well characterized by analytical techniques such as FT-IR, UV-DRS, XRD, SEM-EDX, HR-TEM, EPR, ICP-AES and BET analysis. The characterization results confirmed the grafting of Cu(II) Schiff base complex on the silica surface. The catalytic activity of synthesized silica functionalized Cu(II) acetylacetonate Schiff base complex was evaluated through the oxidative condensation reaction of benzyl alcohol to imine.

Synthesis, Structure and Electrochemistry of Tetranuclear Oxygen-Centered Copper(II) Clusters with Acetylacetone and Benz-pyrazole Hydrolyzed Derivatives as Ligand.

Science.gov (United States)

Vafazadeh, Rasoul; Willis, Anthony C

2016-01-01

Two copper(II) clusters Cu(4)OCl(6)(pyrazole)4, 1, and Cu(4)OBr(6)(Br-pyrazole)4, 2, have been synthesized by reacting acetylacetone and benzohydrazide (1:1 ratio) with CuX(2) (X = Cl for 1 and X= Br for 2) in methanol solutions. The structures of both clusters have been established by X-ray crystallography. The clusters contain four Cu, one O, six μ(2)-X atoms, and four pyrazole ligands. The pyrazoles was prepared in situ by the reaction of acetylacetone with benzohydrazide in methanol under reflux. In 2, the methine hydrogens of the pyrazole ligands have been replaced by bromine atoms. The four copper atoms encapsulate the central O atom in a tetrahedral arrangement. All copper atoms are five-coordinate and have similar coordination environments with slightly distorted trigonal bipyramidal geometry. The cyclic voltammogram of the clusters 1 and 2 show a one-electron quasi-reversible reduction wave in the region 0.485 to 0.731 V, and a one-electron quasi-reversible oxidation wave in the region 0.767 to 0.898 V. In 1, one irreversible oxidative response is observed on the positive of side of the voltammogram at 1.512 V and this can be assigned to Cu(II) to Cu(III) oxidation.

Volatile mixed-ligand lanthanum (3) complex with acetylacetone and 1,10-phenanthroline

International Nuclear Information System (INIS)

Kuz'mina, N.P.; Chuparov, N.V.; Pisarevskij, A.P.; Martynenko, L.I.

1997-01-01

La(Acac) 3 Phen complex is synthetized, its X-tray structure analysis is carried out. Crystals are monoclinic ones, sp.gr. P2 1 /n, a=17.11 (12), b=18.16 (3), c=17.86 (2) A, β=91.32 (2) deg, V=5548 (13) A 3 , Z=8. Structure contains two crystallographically non-equivalent types of molecules differing in interatomic distances and valent angles, as well as, in angles between ligand planes. Behaviour of La(Acac) 3 Phen at heating in vacuum (0.1-0.01 mm Hg) is studied. It is shown that under those conditions processes of Phen splitting, of sublimation and polymerization of La(Acac) 3 lanthanum acetylacetonate formed following Phen splitting and that under 220 deg C during 30 min quantitative transition of La(Acac) 3 Phen into gas phase is reached. 10 refs., 2 figs., 3 tabs

Synthesis And Characterization Of 6,6'-Bis (2-Hydroxyphenyl)-2,2'-Bipyridyl Ligand And Its Platinum Complex for the Interaction with CT-DNA

International Nuclear Information System (INIS)

Norhidayah Selamat; Heng, L.Y.; Nurul Izzaty Hassan; Nurul Huda Abd Karim

2016-01-01

A tetradentate ligand with four donor atoms OONN and its platinum metal complex were synthesized. Bis(phenoxy)bipyridine ligand was prepared by Suzuki coupling reaction between 6,6 ' -dibromo-2,2 ' -bipyridyl and 2-hydroxy phenylboronic acid with the presence of palladium (II) acetate. The formation of platinum complex was done by introducing the ligand with platinum (II) chloride in benzonitrile. Both ligand and complex structures were confirmed by 1 H, 2D cosy and 13 C NMR spectroscopy, ESIMS spectrometry and FTIR spectroscopy. Binding studies of small molecules with DNA are useful to understand the reaction mechanism and to provide guidance for the application and design of new and more efficient drugs or sensors targeted on DNA. In this study, the binding interaction between the synthesized ligand and complex with calf thymus DNA (CT-DNA) has been investigated using UV-Visible and emission DNA titration. From the UV-Visible DNA study, it showed that platinum (II) bipyridine complex had higher affinity towards CT-DNA with binding constant K b =(3.1 ± 0.02 x 10 5 ) ± 0.02 M -1 compared to that of bis(phenoxy) bipyridine ligand with binding constant (K b ) = (1.19 ± 0.08) x 10 3 M -1 . These findings will be valuable for the potential use of platinum (II) bipyridine complex as a phosphorescent probe in optical sensor DNA. (author)

Iodometric determination of platinum(4) using amperometry

International Nuclear Information System (INIS)

Zakharov, V.A.; Gavva, N.F.; Songina, O.A.

1976-01-01

The possibility of iodometric determination of platinum (4) by amperometric titration has been investigated. Titration has been conducted at zero potential of platinum reference electrode. Voltampere curves and absorption spectra of the solutions have been recorded to elucidate the nature of platinum (4) interaction with iodide-ion. It has been established that in the case of small excess of iodide complex [PtI 6 ] 2- is formed. When there is a considerable excess of KI, platinum (4) is reduced to Pt(2) with the formation of [PtI 4 ] 2 - and liberation of free iodine. Optimal for iodometric titration of Pt(4) is the use of acetate ot phosphate background solution with pH 6-8 with respect to 1M KI which is attained by adding 3 g of solid KI to 20 ml of the solution being titrated. Under these conditions the limit of platinum detection is 0.5 mkg/ml. Determination of Pt (4) is not hindered by the presence of 200-fold amounts of Cr(6), V(5), and Ni(2) as well as by 20-10-fold amounts of As(5), Sb(5), Se(4), Te(4), Rh(3), and Ir(3), Determination is hindered by the presence of Pd(2), Fe(3), Ir(4), and Cu(2) which, however, can easily be overcome. The possibility has been shown of using the developed technique for analysis of platinum catalysts and alloys

Surface defect modification of ZnO quantum dots based on rare earth acetylacetonate and their impacts on optical performance

Energy Technology Data Exchange (ETDEWEB)

Wang, Lixi, E-mail: wanglixi_njut@163.com [School of Materials Science and Engineering, Nanjing Tech University, Nanjing, 210009, Jiangsu (China); Jiangsu Collaboration Innovation Center for Advanced Inorganic Function Composites, Nanjing, 210009, Jiangsu (China); Yang, Xiaojuan; Yang, Weimin [School of Materials Science and Engineering, Nanjing Tech University, Nanjing, 210009, Jiangsu (China); Jiangsu Collaboration Innovation Center for Advanced Inorganic Function Composites, Nanjing, 210009, Jiangsu (China); Zhang, Jing [China Geol Survey, Nanjing Ctr, Nanjing, 210016, Jiangsu (China); Zhang, Qitu [School of Materials Science and Engineering, Nanjing Tech University, Nanjing, 210009, Jiangsu (China); Jiangsu Collaboration Innovation Center for Advanced Inorganic Function Composites, Nanjing, 210009, Jiangsu (China); Song, Bo; Wong, Chingping [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, 30332, GA (United States)

2017-03-15

Graphical abstract: RE(AcAc){sub 3} (RE = Ce, Dy and Tb) can realize the defects modification of ZnO QDs based on the linkage occurs between the protons of the hydroxyl groups on the surface of ZnO QDs and the π–system of acetylacetone. The color coordinate could be shifted among yellow-green, blue-green, and green region by changing the RE (AcAc){sub 3} ratios. The stable Ce(AcAc){sub 3}/ZnO QDs with average sizes of about 3.0 nm can be obtained. The calculated band gap data also proved the efficient modification of Ce(AcAc){sub 3} for ZnO QDs with the largest variation of band gap energy of 0.039 eV (from 3.583 eV to 3.544 eV). - Highlights: • Defects modification of ZnO QDs based on rare earth acetylacetonate. • Stable Ce(AcAc){sub 3}/ZnO QDs with an average sizes of about 3.0 nm. • The color coordinate could be shifted among yellow-green, blue-green, and green region by changing the RE (AcAc){sub 3} ratios. - Abstract: The surface defect modification has an important effect on the application of ZnO quantum dots, and it has gained much progress in recently years, propelled by the development of additives. Our research efforts are directed toward developing a new surface modification additive RE(AcAc){sub 3} (RE = Ce, Dy, Tb) to achieve fine ZnO QDs and adjust their surface properties. RE(AcAc){sub 3}/ZnO QDs nanostructured materials have been designed and prepared, and particular emphasis has been given to the relation between the surface modification and optical properties. The effects of RE(III) acetylacetonate modification on the FT-IR, TEM images and photoluminescence (PL) spectra were investigated, and the surface defect modification principle and effect were discussed in details. The band gap (E{sub g}) was also calculated to prove the surface modification effect. For the RE(AcAc){sub 3}/ZnO QDs complex materials, stable linkage occurs because of the affinity of −COOH from acetylacetonate anionic ligand to zinc oxide surfaces, with attachment

Platinum-group elements and gold in base metal sulfides, platinum-group minerals, and Re-Os isotope compositions of the Uitkomst complex, South Africa

Czech Academy of Sciences Publication Activity Database

Trubač, Jakub; Ackerman, Lukáš; Gauert, Ch.; Ďurišová, Jana; Hrstka, Tomáš

2018-01-01

Roč. 113, č. 2 (2018), s. 439-461 ISSN 0361-0128 R&D Projects: GA ČR GA13-15390S Institutional support: RVO:67985831 Keywords : binary alloys * copper compounds * economic geology * gold * iridium * isotopes * ore deposits * osmium * palladium * platinum * platinum metals * pyrites * Rhenium * rhenium alloys * ruthenium * solid solutions * sulfur compounds * crustal materials * mass-balance calculations * massive sulfides * mineralized zone * monosulfide solid solutions * platinum group elements * platinum group elements (PGEs) * platinum group minerals Subject RIV: DB - Geology ; Mineralogy; AC - Archeology, Anthropology, Ethnology (ARUB-Q) OBOR OECD: Geology; Archaeology (ARUB-Q) Impact factor: 2.519, year: 2016

Hydrogen Temperature-Programmed Desorption (H2 TPD) of Supported Platinum Catalysts.

NARCIS (Netherlands)

Koningsberger, D.C.; Miller, J.T.; Meyers, B.L.; Modica, F.S.; Lane, G.S.; Vaarkamp, M.

1993-01-01

Hydrogen temperature-programmed desorption (TPD) of supported platinum catalysts, Pt/KLTL, Pt/H-LTL, Pt/K-MAZ, Pt/H-MAZ, Pt/-Al2O3, and Pt/SiO2, was performed after hydrogen reduction at 300, 450, or 650°C. For all catalysts, reversible desorption of chemisorbed hydrogen occurred at approximately

Platinum nanoparticles embedded in layer-by-layer films from SnO{sub 2}/polyallylamine for ethanol electrooxidation

Energy Technology Data Exchange (ETDEWEB)

Barretto, Caroline B.; Parreira, Renato L.T.; Goncalves, Rogeria R.; Huguenin, Fritz [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, 14040-901 Ribeirao Preto SP (Brazil); de Azevedo, Dayse C. [NovoCell Energy Systems S.A., 13478-722 Americana SP (Brazil)

2008-10-15

Self-assembled films from SnO{sub 2} and polyallylamine (PAH) were deposited on gold via ionic attraction by the layer-by-layer (LbL) method. The modified electrodes were immersed into a H{sub 2}PtCl{sub 6} solution, a current of 100 {mu}A was applied, and different electrodeposition times were used. The SnO{sub 2}/PAH layers served as templates to yield metallic platinum with different particle sizes. The scanning tunnel microscopy images show that the particle size increases as a function of electrodeposition time. The potentiodynamic profile of the electrodes changes as a function of the electrodeposition time in 0.5 mol L{sup -1} H{sub 2}SO{sub 4}, at a sweeping rate of 50 mV s{sup -1}. Oxygen-like species are formed at less positive potentials for the Pt-SnO{sub 2}/PAH film in the case of the smallest platinum particles. Electrochemical impedance spectroscopy measurements in acid medium at 0.7 V show that the charge transfer resistance normalized by the exposed platinum area is 750 times greater for platinum electrode (300 k{omega} cm{sup 2}) compared with the Pt-SnO{sub 2}/PAH film with 1 min of electrodeposition (0.4 k{omega} cm{sup 2}). According to the Langmuir-Hinshelwood bifunctional mechanism, the high degree of coverage with oxygen-like species on the platinum nanoparticles is responsible for the electrocatalytic activity of the Pt-SnO{sub 2}/PAH concerning ethanol electrooxidation. With these features, this Pt-SnO{sub 2}/PAH film may be grown on a proton exchange membrane (PEM) in direct ethanol fuel cells (DEFC). (author)

Novel Platinum-Catalyzed Ring-Opening of 1,2-Cyclopropanated Sugars with Alcohols

DEFF Research Database (Denmark)

Beyer, Jürgen; Madsen, Robert

1998-01-01

Reaction of 1,2-cyclopropanated sugars with a catalytic amount ofZeise's dimer [Pt(C2H4)Cl2]2 and an alcohol gives 2-C-branched glycosides by a novel platinum catalyzed ring-opening. A wide variety of alcohols can participate in this ring-opening reaction giving 2-C-branched glycosides ranging from...

Platinum stable isotopes in ferromanganese crust and nodules

Science.gov (United States)

Corcoran, Loretta; Seward, Terry; Handler, Monica R.

2015-04-01

Hydrogenetic ferromanganese (Fe-Mn) crust and nodules are slow-growing chemical sediments that form by direct precipitation from seawater, resulting in a record of changing seawater chemistry. These sediments are the primary sink for platinum in the modern oxic marine environment, hosting well-documented enrichments over other platinum-group elements (PGEs): the Pt anomaly [1]. Platinum is a non-bio-essential, highly siderophile, transition metal with six stable isotopes (190Pt, 192Pt, 194Pt, 195Pt, 196Pt, and 198Pt) with several oxidation states (Pt0, Pt2+ and Pt4+). Platinum is generally considered to exist in the hydrosphere as Pt2+ although its behaviour in the marine environment is poorly constrained, and Pt4+may also be present. Variations in ocean redox state, together with changes in source fluxes to the oceans, may therefore lead to small variations (Leaching experiments conducted on platinum rich terrestrial materials underwent platinum stable isotopic measurement as an analogue for the Pt isotopic fractionation associated with continental weathering. [1] Hodge, V.F. et al. (1985) Earth and Planetary Science Letters, 72, 158-162. [2] Creech, J. et al. (2013) Journal of Analytical Atomic Spectrometry, 28. 853-865.

Synthesis of platinum nanowire networks using a soft template.

Science.gov (United States)

Song, Yujiang; Garcia, Robert M; Dorin, Rachel M; Wang, Haorong; Qiu, Yan; Coker, Eric N; Steen, William A; Miller, James E; Shelnutt, John A

2007-12-01

Platinum nanowire networks have been synthesized by chemical reduction of a platinum complex using sodium borohydride in the presence of a soft template formed by cetyltrimethylammonium bromide in a two-phase water-chloroform system. The interconnected polycrystalline nanowires possess the highest surface area (53 +/- 1 m2/g) and electroactive surface area (32.4 +/- 3.6 m2/g) reported for unsupported platinum nanomaterials; the high surface area results from the small average diameter of the nanowires (2.2 nm) and the 2-10 nm pores determined by nitrogen adsorption measurements. Synthetic control over the network was achieved simply by varying the stirring rate and reagent concentrations, in some cases leading to other types of nanostructures including wormlike platinum nanoparticles. Similarly, substitution of a palladium complex for platinum gives palladium nanowire networks. A mechanism of formation of the metal nanowire networks is proposed based on confined metal growth within a soft template consisting of a network of swollen inverse wormlike micelles.

Room temperature synthesis of colloidal platinum nanoparticles

Indian Academy of Sciences (India)

Unknown

platinum cation used. ... Particle size increased with low reagent concentration. ... 2,100) was added separately to the starting solution. Argon gas was bubbled in the solution for 20 min. Later, reduction of platinum ions was carried out by bubbling hydrogen gas ... plex to aquate (Cl– → H2O ligand exchange). ... copper grid.

Mass spectrometry study of sublimation of rare earth acetylacetonate adducts with hexamethylphosphorustriamide

International Nuclear Information System (INIS)

Kuz'mina, N.P.; Semyannikov, P.P.; Martynenko, L.I.; Ch'eu Tkhi Nguet; AN SSSR, Novosibirsk

1991-01-01

Process of vacuum sublimation of MA 3 ·Q adducts (M=Nd,Ho,Er; A - -acetylacetonate-ion; Q-hexamethylphosphorustriamide) was studied by mass-spectrometry method. Composinion of gaseous phase, formed in 20-140 deg C range at 10 -5 mm Hg, was determined. Scheme of MA 3 ·Q sublimation, including Q splitting and transition of MA 3 ·Q adducts and MA 3 and Q products of their thermodestruction to gaseous phase, was suggested. ΔH values of MA 3 ·Q thermodestruction and MA 3 sublimation were calculated

Surfactant controlled low-temperature thermal decomposition route to zinc oxide nanorods from zinc(II) acetylacetonate monohydrate

Energy Technology Data Exchange (ETDEWEB)

Purkayastha, Debraj Dhar; Sarma, Bedabrat; Bhattacharjee, Chira R., E-mail: crbhattacharjee@rediffmail.com

2014-10-15

Zinc oxide (ZnO) nanorods were synthesized via a low-temperature thermal decomposition of zinc(II) acetylacetonate monohydrate, [Zn(C{sub 5}H{sub 7}O{sub 2}){sub 2}].H{sub 2}O. A relatively inexpensive surfactant, octadecylamine (C{sub 18}H{sub 37}NH{sub 2}) served both as a reaction solvent and a capping agent during the synthesis of ZnO nanorods. The synthesized nanorods were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), FT-IR, UV–visible, and photoluminescence (PL) studies. The XRD spectrum furnished evidence for the hexagonal wurtzite structure of ZnO. TEM images revealed the material to be rod shaped having diameter 30 nm and length 200 nm. The HRTEM image showed that the lattice fringes between the two adjacent planes are 0.244 nm apart, which corresponds to the interplanar separation of the (1 0 1) plane of hexagonal ZnO. The electron diffraction (ED) pattern confirmed the single crystalline nature of the nanorods. The PL spectrum showed two UV emissions at 356 nm (∼3.48 eV) and 382 nm (∼3.25 eV). ZnO nanorods also showed very weak blue bands at 445, 453 and 470 nm. - Highlights: Low temperature thermal decomposition of zinc(II) acetylacetonate monohydrate gave zinc oxide nanorods. Powder XRD showed hexagonal wurtzite structure of ZnO having average diameter about 24 nm. TEM images revealed the material to be of rod shape having diameter 30 nm and length 200 nm. ZnO showed band gap luminescence at 356 nm, excitonic emission at 382 nm and defect related blue bands. The synthesis is simple and can act as a paradigm for obtaining various metal oxide nanomaterials.

Contribution to the study of the chemical consequences of the (n, {gamma}) reaction in solid Co(3) tris-acetylacetone; Contribution a l'etude des consequences chimiques de la reaction (n, {gamma}) dans le tris-acetylacetonate de cobalt (3)

Energy Technology Data Exchange (ETDEWEB)

Magnane Machado, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

The fragmentation and annealing of thermal neutron irradiated Co(III) tris-acetylacetone was investigated using the thin layer chromatographic technique (silica-gel 1 mm thickness). Low temperature irradiations (0 C - -72 C and -180 C) lead to {sup 60}Co retentions as low as (1,1 {+-} 0,2) per cent. Annealing by linear temperature programming at different heating rates has shown the existence of eight reactions. The influences of pile dose and of gases (air and helium) as well as of thermal decomposition on the annealing processes were confirmed. A temperature and dose dependent effect was found out for the retentions of the {sup 60m}Co - {sup 60}Co isomers. (author) [French] On a etudie par chromatographie en couches minces (silicagel 1 mm), les phenomenes de fragmentation et de recuit sur l'acetylacetonate de Co(III) irradie aux neutrons thermiques. La valeur minimale de la retention observee pour des irradiations a basse temperature (0 C, -72 C, -180 C) se situe a (1,1 {+-} 0,2) pour cent. Le recuit thermique, par montee lineaire de la temperature a differentes vitesses de chauffage, montre l'existence de huit reactions. On confirme, de plus, l'influence sur les processus de recuit de la dose recue en pile, de l'atmosphere dans laquelle l'echantillon se trouve (air et helium) ainsi que de la decomposition thermique. Cette dependance de la temperature et de la dose est prouvee par les valeurs des retentions mesurees sur les isomeres {sup 60m}Co - {sup 60}Co. (auteur)

Comparison of indium-111-oxine and indium-111-acetylacetone labelled leucocytes in the diagnosis of inflammatory disease

Energy Technology Data Exchange (ETDEWEB)

Peters, A.M.; Karimjee, S.; Saverymuttu, S.H.; Lavender, J.P. (Hammersmith Hospital, London (UK))

1982-11-01

/sup 111/In leucocyte scanning in a series of 132 patients has shown this technique to be a reliable and accurate means of diagnosing sepsis. Labelling with /sup 111/In oxine and with /sup 111/In acetylacetone gave similar values of sensitivity and specificity, and higher than those of ultrasound.

Vanadium oxide thin films and fibers obtained by acetylacetonate sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Berezina, O.; Kirienko, D. [Department of Physical Engineering, Petrozavodsk State University, 185910 Petrozavodsk (Russian Federation); Pergament, A., E-mail: aperg@psu.karelia.ru [Department of Physical Engineering, Petrozavodsk State University, 185910 Petrozavodsk (Russian Federation); Stefanovich, G.; Velichko, A. [Department of Physical Engineering, Petrozavodsk State University, 185910 Petrozavodsk (Russian Federation); Zlomanov, V. [Department of Chemistry, Moscow State University, 119991 Moscow (Russian Federation)

2015-01-01

Vanadium oxide films and fibers have been fabricated by the acetylacetonate sol–gel method followed by annealing in wet nitrogen. The samples are characterized by X-ray diffraction and electrical conductivity measurements. The effects of a sol aging, the precursor decomposition and the gas atmosphere composition on the annealing process, structure and properties of the films are discussed. The two-stage temperature regime of annealing of amorphous films in wet nitrogen for formation of the well crystallized VO{sub 2} phase is chosen: 1) 25–550 °C and 2) 550–600 °C. The obtained films demonstrate the metal–insulator transition and electrical switching. Also, the effect of the polyvinylpyrrolidone additive concentration and electrospinning parameters on qualitative (absence of defects and gel drops) and quantitative (length and diameter) characteristics of vanadium oxide fibers is studied. - Highlights: • Vanadium oxide thin films and fibers are synthesized by sol–gel method. • The effect of annealing, atmosphere, time and electrospinning parameters is studied. • Produced VO{sub 2} structures exhibit metal–insulator transition and electrical switching.

Infinite dilution partial molar volumes of platinum(II) 2,4-pentanedionate in supercritical carbon dioxide.

Science.gov (United States)

Kong, Chang Yi; Siratori, Tomoya; Funazukuri, Toshitaka; Wang, Guosheng

2014-10-03

The effects of temperature and density on retention of platinum(II) 2,4-pentanedionate in supercritical fluid chromatography were investigated at temperatures of 308.15-343.15K and pressure range from 8 to 40MPa by the chromatographic impulse response method with curve fitting. The retention factors were utilized to derive the infinite dilution partial molar volumes of platinum(II) 2,4-pentanedionate in supercritical carbon dioxide. The determined partial molar volumes were small and positive at high pressures but exhibited very large and negative values in the highly compressible near critical region of carbon dioxide. Copyright © 2014 Elsevier B.V. All rights reserved.

High performance platinum single atom electrocatalyst for oxygen reduction reaction

Science.gov (United States)

Liu, Jing; Jiao, Menggai; Lu, Lanlu; Barkholtz, Heather M.; Li, Yuping; Wang, Ying; Jiang, Luhua; Wu, Zhijian; Liu, Di-Jia; Zhuang, Lin; Ma, Chao; Zeng, Jie; Zhang, Bingsen; Su, Dangsheng; Song, Ping; Xing, Wei; Xu, Weilin; Wang, Ying; Jiang, Zheng; Sun, Gongquan

2017-07-01

For the large-scale sustainable implementation of polymer electrolyte membrane fuel cells in vehicles, high-performance electrocatalysts with low platinum consumption are desirable for use as cathode material during the oxygen reduction reaction in fuel cells. Here we report a carbon black-supported cost-effective, efficient and durable platinum single-atom electrocatalyst with carbon monoxide/methanol tolerance for the cathodic oxygen reduction reaction. The acidic single-cell with such a catalyst as cathode delivers high performance, with power density up to 680 mW cm-2 at 80 °C with a low platinum loading of 0.09 mgPt cm-2, corresponding to a platinum utilization of 0.13 gPt kW-1 in the fuel cell. Good fuel cell durability is also observed. Theoretical calculations reveal that the main effective sites on such platinum single-atom electrocatalysts are single-pyridinic-nitrogen-atom-anchored single-platinum-atom centres, which are tolerant to carbon monoxide/methanol, but highly active for the oxygen reduction reaction.

Material and Energy Flows Associated with Select Metals in GREET 2. Molybdenum, Platinum, Zinc, Nickel, Silicon

Energy Technology Data Exchange (ETDEWEB)

Benavides, Pahola T. [Argonne National Lab. (ANL), Argonne, IL (United States); Dai, Qiang [Argonne National Lab. (ANL), Argonne, IL (United States); Sullivan, John L. [Argonne National Lab. (ANL), Argonne, IL (United States); Kelly, Jarod C. [Argonne National Lab. (ANL), Argonne, IL (United States); Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-09-01

In this work, we analyzed the material and energy consumption from mining to production of molybdenum, platinum, zinc, and nickel. We also analyzed the production of solar- and semiconductor-grade silicon. We described new additions to and expansions of the data in GREET 2. In some cases, we used operating permits and sustainability reports to estimate the material and energy flows for molybdenum, platinum, and nickel, while for zinc and silicon we relied on information provided in the literature.

Surface-initiated addition polymerization of norbornene by a Pd(II) catalyst bearing acetylacetone ligand on the glass slide

Science.gov (United States)

He, Xiaohui; Wang, Kaiti; Chen, Yiwang; Yuan, Bin

2012-02-01

A Pd catalyst bearing acetylacetone ligand [(CH3CO)2CHPdCl2] was covalently attracted onto the surface of glass slides, and then these Pd-terminated glass slides were immersed into a toluene solution of norbornene (NB) to produce a vinyl-type addition polynorbornene (PNB) layer on the surface of glass slides. It was found that the contract angles of the PNB-terminated glass slides surface increased with the increasing of polymerization time, and the thickness of the PNB layers were approximately 0-44.0 μm when the polymerization time was 0.5-24 h. The researching on etching also has been operated.

OFFGEL isoelectric focusing and polyacrylamide gel electrophoresis separation of platinum-binding proteins.

Science.gov (United States)

Mena, Ma Luz; Moreno-Gordaliza, Estefanía; Moraleja, Irene; Cañas, Benito; Gómez-Gómez, Ma Milagros

2011-03-04

In this work a 2D electrophoretic separation procedure able to maintain the integrity of platinum-protein bonds has been developed. The method is based on the use of sequential OFFGEL isoelectric focussing (IEF) and PAGE. A systematic study of the reagents used for PAGE, for OFFGEL-IEF separation, and post-separation treatment of gels (such as enzymatic digestion and sample preparation for MS analysis) was tackled regarding their suitability for the identification of platinum binding proteins using standard proteins incubated with cisplatin. The distribution of platinum in high and low molecular weight fractions (separated by cut-off filters) was determined by ICP-MS, which allows evaluating platinum-protein bond stability under the conditions studied. SDS-PAGE in the absence of β-mercaptoethanol or dithiotreitol preserved the platinum-protein bonds. In addition, neither the influence of the electric field during the electrophoretic separation, nor the processes of fixing, staining and destaining of proteins in the gel did result in the loss of platinum from platinum binding proteins. SDS-PAGE under non-reducing conditions provides separation of platinum-binding proteins in very narrow bands with quantitative recoveries. Different amounts of platinum-bound proteins covering the range 0.3-2.0 μg were separated and mineralised for platinum determination, showing good platinum linearity. Limits of detection for a mixture of five standard proteins incubated with cisplatin were between the range of 2.4 and 13.9 pg of platinum, which were satisfactory for their application to biological samples. Regarding OFFGEL-IEF, a denaturing solution without thiourea and without dithiotreitol is recommended. The suitability of the OFFGEL-IEF for the separation of platinum binding proteins of a kidney cytosol was demonstrated. Copyright © 2011 Elsevier B.V. All rights reserved.

Reactions of neopentane and neohexane on platinum/Y-zeolite and platinum/silica catalysts

Energy Technology Data Exchange (ETDEWEB)

Foger, K.; Anderson, J.R.

1978-10-13

The hydrocracking/hydroisomerization reaction of 20:1 hydrogen/neopentane at 455-625/sup 0/K was studied on platinum-exchanged sodium, calcium, and lanthanum Y zeolites and Aerosil-supported platinum of 1-20 nm average platinum particle size, by analysis of the product distribution, ESCA, and temperature-programed desorption. The results suggested that the reaction occurs only on platinum and that it proceeds by two parallel pathways which have different activation energies and whose relative proportion depends on the particle size. One pathway is the conventionally accepted one on low-index crystallite facets; the other proceeds on single-surface platinum atoms of low coordination (corner or edge atoms) which become more abundant at lower crystallite size. In both cases, the adsorbed intermediate may undergo either isomerization or hydrogenolysis; the selectivity depends on the hydrogen partial pressure and the relative strength of adsorption of hydrogen and neopentane. Neohexane isomerization selectivity on the same catalysts is consistent with a carbonium ion mechanism on a dual-function catalyst.

Rapid and facile CuCl assistant synthesis of PtCu3 nanoframes as efficient catalysts for electroxidation of methanol

Science.gov (United States)

Bai, Lei; Bai, Yuwei

2018-02-01

Hollow-structured nanomaterials generally showed enhanced catalytic abilities due to their high utilization. In this work, a general method for the synthesis of PtCu3 nanoframes was reported with the employment of hexadecyltrimethylammonium chloride (CTAC), copper(I) chloride, and various kinds of platinum precursors such as K2PtCl6, H2PtCl6, and Pt(acac)2. It was revealed that the presence of CTAC was crucial for the formation of frame structures. On the one hand, CTAC could act as a structure director, and on the other hand, the galvanic replacement and etching effect of the chloride ions together with oxygen was also responsible for the formation of the frame structure. A similar effect was also evidenced in the case of hexadecyltrimethylammonium bromide. Finally, the as-obtained PtCu3 nanoframes demonstrated high catalytic abilities in the oxidation of methanol as a model reaction. [Figure not available: see fulltext.

Pt-doped In{sub 2}O{sub 3} nanoparticles prepared by flame spray pyrolysis for NO{sub 2} sensing

Energy Technology Data Exchange (ETDEWEB)

Inyawilert, K. [Chiang Mai University, Department of Physics and Materials Science, Faculty of Science (Thailand); Channei, D. [Naresuan University, Department of Chemistry, Faculty of Science (Thailand); Tamaekong, N. [Maejo University, Program in Materials Science, Faculty of Science (Thailand); Liewhiran, C. [Chiang Mai University, Department of Physics and Materials Science, Faculty of Science (Thailand); Wisitsoraat, A.; Tuantranont, A. [National Electronics and Computer Technology Center (NECTEC), Nanoelectronics and MEMS Laboratory (Thailand); Phanichphant, S., E-mail: sphanichphant@gmail.com [Chiang Mai University, Faculty of Science, Materials Science Research Center (Thailand)

2016-02-15

Undoped In{sub 2}O{sub 3} and 0.25–1.00 wt% M (M=Pt, Nb, and Ru)-doped/loaded In{sub 2}O{sub 3} nanoparticles were successfully synthesized in a single-step flame spray pyrolysis technique using indium nitrate, platinum (II) acetylacetonate, niobium ethoxide, and ruthenium (III) acetylacetonate precursors. The undoped In{sub 2}O{sub 3} and M-doped In{sub 2}O{sub 3} nanoparticles were characterized by Brunauer–Emmett–Teller (BET) analysis, X-ray diffraction (XRD), and scanning and transmission electron microscopy (SEM & TEM). The BET average diameter of spherical nanoparticles was found to be in the range of 10.2–15.2 nm under 5/5 (precursor/oxygen) flame conditions. All XRD peaks were confirmed to correspond to the cubic structure of In{sub 2}O{sub 3}. TEM images showed that there is no Pt nanoparticle loaded on In{sub 2}O{sub 3} surface, suggesting that Pt should form solid solution with the In{sub 2}O{sub 3} lattice. Gas sensing studies showed that 0.5 wt% Pt doping in In{sub 2}O{sub 3} nanoparticles gave a significant enhancement of NO{sub 2} sensing performances in terms of sensor response and selectivity. 0.5 wt% Pt/In{sub 2}O{sub 3} exhibited a high NO{sub 2} response of ∼1904 to 5 ppm NO{sub 2} at 250 °C and good NO{sub 2} selectivity against NO, H{sub 2}S, H{sub 2}, and C{sub 2}H{sub 5}OH. In contrast, Nb and Ru loading resulted in deteriorated NO{sub 2} response. Therefore, Pt is demonstrated to be an effective additive to enhance NO{sub 2} sensing performances of In{sub 2}O{sub 3}-based sensors.

Bio-inspired routes for synthesizing efficient nanoscale platinum electrocatalysts

Energy Technology Data Exchange (ETDEWEB)

Cha, Jennifer N. [Univ. of California, San Diego, CA (United States); Wang, Joseph [Univ. of California, San Diego, CA (United States)

2014-08-31

The overall objective of the proposed research is to use fundamental advances in bionanotechnology to design powerful platinum nanocrystal electrocatalysts for fuel cell applications. The new economically-viable, environmentally-friendly, bottom-up biochemical synthetic strategy will produce platinum nanocrystals with tailored size, shape and crystal orientation, hence leading to a maximum electrochemical reactivity. There are five specific aims to the proposed bio-inspired strategy for synthesizing efficient electrocatalytic platinum nanocrystals: (1) isolate peptides that both selectively bind particular crystal faces of platinum and promote the nucleation and growth of particular nanocrystal morphologies, (2) pattern nanoscale 2-dimensional arrays of platinum nucleating peptides from DNA scaffolds, (3) investigate the combined use of substrate patterned peptides and soluble peptides on nanocrystal morphology and growth (4) synthesize platinum crystals on planar and large-area carbon electrode supports, and (5) perform detailed characterization of the electrocatalytic behavior as a function of catalyst size, shape and morphology. Project Description and Impact: This bio-inspired collaborative research effort will address key challenges in designing powerful electrocatalysts for fuel cell applications by employing nucleic acid scaffolds in combination with peptides to perform specific, environmentally-friendly, simultaneous bottom-up biochemical synthesis and patterned assembly of highly uniform and efficient platinum nanocrystal catalysts. Bulk synthesis of nanoparticles usually produces a range of sizes, accessible catalytic sites, crystal morphologies, and orientations, all of which lead to inconsistent catalytic activities. In contrast, biological systems routinely demonstrate exquisite control over inorganic syntheses at neutral pH and ambient temperature and pressures. Because the orientation and arrangement of the templating biomolecules can be precisely

Role of Platinum Deposited on TiO2 in Photocatalytic Methanol Oxidation and Dehydrogenation Reactions

Directory of Open Access Journals (Sweden)

Luma M. Ahmed

2014-01-01

Full Text Available Titania modified nanoparticles have been prepared by the photodeposition method employing platinum particles on the commercially available titanium dioxide (Hombikat UV 100. The properties of the prepared photocatalysts were investigated by means of the Fourier transform infrared spectroscopy (FTIR, X-ray diffraction (XRD, atomic force microscopy (AFM, and UV-visible diffuse spectrophotometry (UV-Vis. XRD was employed to determine the crystallographic phase and particle size of both bare and platinised titanium dioxide. The results indicated that the particle size was decreased with the increasing of platinum loading. AFM analysis showed that one particle consists of about 9 to 11 crystals. UV-vis absorbance analysis showed that the absorption edge shifted to longer wavelength for 0.5% Pt loading compared with bare titanium dioxide. The photocatalytic activity of pure and Pt-loaded TiO2 was investigated employing the photocatalytic oxidation and dehydrogenation of methanol. The results of the photocatalytic activity indicate that the platinized titanium dioxide samples are always more active than the corresponding bare TiO2 for both methanol oxidation and dehydrogenation processes. The loading with various platinum amounts resulted in a significant improvement of the photocatalytic activity of TiO2. This beneficial effect was attributed to an increased separation of the photogenerated electron-hole charge carriers.

Study of gold-platinum and platinum-gold surface modification and its influence on hydrogen evolution and oxygen reduction

Directory of Open Access Journals (Sweden)

BRANIMIR N. GRGUR

2005-02-01

Full Text Available Surface modification of the electrodes was conducted from sulfuric acid solutions containing the corresponding metal–chloride complexes using cyclic voltammetry. Comparing the charges of the hydrogen underpotential deposition region, and the corresponding oxide reduction regions, it is concluded that a platinum overlayer on gold forms 3D islands, while gold on platinum forms 2D islands. Foreign metals present in an amount of up to one monolayer exert an influence on the change in reaction rate with respect to both hydrogen evolution (HER and oxygen reduction (ORR reactions. Aplatinum overlayer on a gold substrate increases the activity forHER and for ORR, compared with pure gold. These results can be understood in terms of a simple model, in which the change in the H and OH binding energies are directly proportional to the shift of the d-bond center of the overlayer. On the contrary, a gold layer on platinum slightly decreases the activity for both reactions compared with pure platinum.

Phosphoric acid fuel cell platinum use study

Science.gov (United States)

Lundblad, H. L.

1983-05-01

The U.S. Department of Energy is promoting the private development of phosphoric acid fuel cell (PAFC) power plants for terrestrial applications. Current PAFC technology utilizes platinum as catalysts in the power electrodes. The possible repercussions that the platinum demand of PAFC power plant commercialization will have on the worldwide supply and price of platinum from the outset of commercialization to the year 2000 are investigated. The platinum demand of PAFC commercialization is estimated by developing forecasts of platinum use per unit of generating capacity and penetration of PAFC power plants into the electric generation market. The ability of the platinum supply market to meet future demands is gauged by assessing the size of platinum reserves and the capability of platinum producers to extract, refine and market sufficient quantities of these reserves. The size and timing of platinum price shifts induced by the added demand of PAFC commercialization are investigated by several analytical methods. Estimates of these price shifts are then used to calculate the subsequent effects on PAFC power plant capital costs.

Separation of deuterium by H2/H2O reaction with hydrophobic platinum catalyst

International Nuclear Information System (INIS)

Kitamoto, A.; Takashima, Y.; Shimizu, M.

The separation performance of a trickle bed exchange column packed with a hydrophobic or waterproof catalyst is related to operating conditions such as hydrogen surface velocity, water flow rate, and temperature. The optimum carrier type and catalyst platinum content were determined. The continuous injection of roughly 10 3 ppm O 2 regenerates the catalyst effectively. The ratio of hydrophobic catalyst to hydrophilic packing is an important factor in increasing the exchange rate in deuterium extraction

Platinum-group elements

Science.gov (United States)

Zientek, Michael L.; Loferski, Patricia J.; Parks, Heather L.; Schulte, Ruth F.; Seal, Robert R.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

generally considered to be inert. PGEs pose a risk to human health only in cases where individuals are occupationally exposed to synthetic PGE compounds, especially workers in precious-metal refineries. In the natural environment, background PGE concentrations are low in water, sediment, soil, and plants. Anthropogenic sources of PGEs in the environment include catalytic converters used in modern automobiles, platinum-based chemotherapy drugs, and smelter emissions.The abundance of sulfide minerals defines the environmental and geologic characteristics of PGE-enriched magmatic sulfide deposits; those deposits with the highest amount of sulfide minerals could have the highest environmental impact. Acid rock drainage from reef-type and contact-type deposits is unlikely because the ores and their host rocks contain low proportions of sulfide minerals. For some conduit-type orebodies with massive ores, mineral-processing techniques separate and produce concentrates of copper-, iron-, and nickel-bearing sulfide minerals; those with copper and nickel are processed to extract metal, but the iron-sulfide minerals, mainly pyrrhotite, are discarded as waste. This results in waste material with a high acid-generating potential.The most significant primary source of PGEs in the United States is a deposit in the Stillwater Complex, which is a layered igneous intrusion in Montana. Approximately 305 metric tons of platinum and palladium have been mined from the Stillwater Complex deposit since 1986. Exploration and development drilling indicate that another 2,200 metric tons are present. Mining has progressed to depths of 1,800 meters below the surface, but the bottom of the ore deposit has not been reached; geologic estimates suggest that another 1,000 to 6,200 metric tons of PGEs could be present at depth. In the future, PGEs may be mined from deposits found near the base of the Duluth Complex, which is a group of igneous intrusions in Minnesota.

Determination of trace platinum by supramolecular catalytic kinetic spectrofluorimetry of {beta}-cyclodextrin-platinum-KBrO{sub 3}-salicylaldehyde furfuralhydrazone

Energy Technology Data Exchange (ETDEWEB)

Tang, Bo; Zhang, Ning; Chen, Zhen-Zhen; Kong, Qing-Cheng [Shandong Normal University, College of Chemistry, Chemical Engineering and Materials Science, Jinan (China)

2006-02-01

A supramolecular catalytic kinetic spectrofluorimetric method was developed for the determination of platinum(IV) and the possible mechanism of catalytic reaction was discussed. The method was based on the fluorescence-enhancing reaction of salicylaldehyde furfuralhydrazone (SAFH) with potassium bromate, which was catalysed by platinum(IV) in a water-ethanol medium. {beta}-Cyclodextrin ({beta}-CD) obviously sensitized the determination at pH 5.20 and 25 C. Under optimum conditions, the {beta}-CD-platinum-KBrO{sub 3}-SAFH supramolecular kinetic catalytic reaction system had excitation and emission maxima at 372 and 461 nm, respectively. The linear range of this method was 0.60-180 ng ml{sup -1} with a relative standard deviation of 1.2%, and the detection limit was 0.18 ng ml{sup -1}. Investigation of the mechanism and the effects of interferences is presented. The proposed method was applied successfully to determine trace platinum(IV) in the chemotherapeutic drug cisplatin and serum from patients with satisfactory results. (orig.)

A phase 2, open-label, multi-center study of amuvatinib in combination with platinum etoposide chemotherapy in platinum-refractory small cell lung cancer patients.

Science.gov (United States)

Byers, Lauren Averett; Horn, Leora; Ghandi, Jitendra; Kloecker, Goetz; Owonikoko, Taofeek; Waqar, Saiama Naheed; Krzakowski, Maciej; Cardnell, Robert J; Fujimoto, Junya; Taverna, Pietro; Azab, Mohammad; Camidge, David Ross

2017-10-06

Amuvatinib (MP-470) is a multi-targeted kinase inhibitor with potent activity against c-Kit, synergistic with DNA-damaging agents. We evaluated amuvatinib in combination with platinum-etoposide (EP) chemotherapy by objective response rate, survival, and tolerability in platinum-refractory small cell lung cancer (SCLC) patients. This study used a Simon 2-stage design requiring ≥3 centrally confirmed responses in the first 21 subjects. Subjects received EP with 300 mg amuvatinib orally three times daily in cycles of 21 days. A three-day amuvatinib run-in period before EP occurred in Cycle 1. Subjects received the same EP chemotherapy regimen given prior to progression/relapse. Among 23 subjects treated, we observed four PRs (17.4%) per RECIST 1.1, only two of which were centrally confirmed (8.7%, response duration 119, 151 days). Three subjects (13%) had confirmed stable disease. c-Kit H-score was ≥100 in two subjects whose respective durations of disease control were 151 and 256 days. The addition of amuvatinib to EP chemotherapy in unselected, platinum-refractory SCLC did not meet the primary endpoint of ≥3 confirmed responses in stage 1. However, high c-Kit expression in two subjects with durable disease control suggests the potential for further study of amuvatinib in SCLC patients with high c-Kit expression.

Developments in platinum anticancer drugs

Science.gov (United States)

Tylkowski, Bartosz; Jastrząb, Renata; Odani, Akira

2018-01-01

Platinum compounds represent one of the great success stories of metals in medicine. Following the unexpected discovery of the anticancer activity of cisplatin (Fig. 1) in 1965 by Prof. Rosenberg [1], a large number of its variants have been prepared and tested for their ability to kill cancer cells and inhibit tumor growth. Although cisplatin has been in use for over four decades, new and more effective platinum-based therapeutics are finally on the horizon. A wide introduction to anticancer studies is given by the authors of the previous chapter. This chapter aims at providing the readers with a comprehensive and in-depth understanding of recent developments of platinum anticancer drugs and to review the state of the art. The chapter is divided into two parts. In the first part we present a historical aspect of platinum and its complexes, while in the second part we give an overview of developments in the field of platinum anticancer agents.

Synthesis of platinum nanowheels using a bicellar template.

Science.gov (United States)

Song, Yujiang; Dorin, Rachel M; Garcia, Robert M; Jiang, Ying-Bing; Wang, Haorong; Li, Peng; Qiu, Yan; van Swol, Frank; Miller, James E; Shelnutt, John A

2008-09-24

Disk-like surfactant bicelles provide a unique meso-structured reaction environment for templating the wet-chemical reduction of platinum(II) salt by ascorbic acid to produce platinum nanowheels. The Pt wheels are 496 +/-55 nm in diameter and possess thickened centers and radial dendritic nanosheets (about 2-nm in thickness) culminating in flared dendritic rims. The structural features of the platinum wheels arise from confined growth of platinum within the bilayer that is also limited at edges of the bicelles. The size of CTAB/FC7 bicelles is observed to evolve with the addition of Pt(II) complex and ascorbic acid. Synthetic control is demonstrated by varying the reaction parameters including metal salt concentration, temperature, and total surfactant concentration. This study opens up opportunities for the use of other inhomogeneous soft templates for synthesizing metals, metal alloys, and possibly semiconductors with complex nanostructures.

On the enzymatic formation of platinum nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Govender, Y.; Riddin, T. L. [Rhodes University, Department of Biochemistry, Microbiology and Biotechnology (South Africa); Gericke, M. [MINTEK (South Africa); Whiteley, C. G., E-mail: C.Whiteley@ru.ac.z [Rhodes University, Department of Biochemistry, Microbiology and Biotechnology (South Africa)

2010-01-15

A dimeric hydrogenase enzyme (44.5 and 39.4 kDa sub units) was isolated in a 39.5% yield from the fungus Fusarium oxysporum and purified 4.64-fold by ion exchange chromatography on Sephacryl S-200. Characterisation of the enzyme afforded pH and temperature optima of 7.5 and 38 {sup o}C, respectively, a half-life stability of 36 min and a V{sub max} and K{sub m} of 3.57 nmol min{sup -1} mL{sup -1} and 2.25 mM, respectively. This enzyme was inhibited (non-competitively) by hydrogen hexachloroplatinic acid (H{sub 2}PtCl{sub 6}) at 1 or 2 mM with a K{sub i} value of 118 {mu}M. Incubation of the platinum salt with the pure enzyme under an atmosphere of hydrogen and optimum enzyme conditions (pH 7.5, 38 {sup o}C) afforded <10% bioreduction after 8 h while at conditions suitable for platinum nanoparticle formation (pH 9, 65 {sup o}C) over 90% reduction took place after the same length of time. Cell-free extract from the fungal isolates produced nearly 90% bioreduction of the platinum salt under both pH and temperature conditions. The bioreduction of the platinum salt by a hydrogenase enzyme takes place by a passive process and not an active one as previously understood.

Studies on the distribution of platinum in tumour-bearing rats after the administration of platinum co-ordination complexes used in cancer chemotherapy

International Nuclear Information System (INIS)

Zeisler, R.; Lux, F.; Beck, W.

1979-01-01

Platinum co-ordination complexes like dichlorodiamineplatinum(II) (DDP) feature broad spectrum antitumour activity which, however, is marred by a certain toxicity related especially to renal tubular damage. The activity of such drugs depends on the chemical structure of the complexes, with changes in the ligands resulting in changes in their antitumour activity and toxicity. Assessments of the biological and toxicological effects of recently synthesized complexes must include distribution studies of platinum in the body. It is demonstrated that instrumental neutron activation analysis can be used for these studies because of its accuracy, precision and the low detection limit for platinum (approximately equal to 2 ng), when a standardized method is used. The time-dependent retention of platinum was determined in blood, liver, kidneys and cells of ascitic Walker 256 carcinosarcoma in tumour-bearing rats and controls after the administration of the cis-Pt(Gly-Gly-0Et) 2 Cl 2 complex. Two series of experiments, one with the therapeutic amount of the drug (80 mg/kg body weight) and one low-dose experiment with 1/100 of this amount, were carried out. The results of both experiments are discussed with regard to changes in the platinum concentration with time (0-48 h) in the different samples. From the data a selective uptake of the drug by the tumour cells, causing their destruction, is deduced. Because this drug has shown excellent antitumour activity, this observed selectivity suggests promise for its application in cancer chemotherapy, although platinum retention is still found in the kidneys, which might cause renal tubular damage. This latter aspect requires further clinical research to evaluate fully its effects. (author)

TP53 status and taxane-platinum versus platinum-based therapy in ovarian cancer patients: A non-randomized retrospective study

Directory of Open Access Journals (Sweden)

Markowska Janina

2008-01-01

Full Text Available Abstract Background Taxane-platinum therapy (TP has replaced platinum-based therapy (PC or PAC, DNA damaging chemotherapy in the postoperative treatment of ovarian cancer patients; however, it is not always effective. TP53 protein plays a differential role in response to DNA-damaging agents and taxanes. We sought to define profiles of patients who benefit the most from TP and also of those who can be treated with PC. Methods We compared the effectiveness of PC/PAC (n = 253 and TP (n = 199 with respect to tumor TP53 accumulation in ovarian cancer patients with FIGO stage IIB-IV disease; this was a non-randomized retrospective study. Immunohistochemical analysis was performed on 452 archival tumors; univariate and multivariate analysis by the Cox's and logistic regression models was performed in all patients and in subgroups with [TP53(+] and without TP53 accumulation [TP53(-]. Results The advantage of taxane-platinum therapy over platinum-based therapy was seen in the TP53(+, and not in the TP53(- group. In the TP53(+ group taxane-platinum therapy enhanced the probability of complete remission (p = .018, platinum sensitivity (p = .014, platinum highly sensitive response (p = .038 and longer survival (OS, p = .008. Poor tumor differentiation diminished the advantage from taxane-platinum therapy in the TP53(+ group. In the TP53(- group PC/PAC was at least equally efficient as taxane-platinum therapy and it enhanced the chance of platinum highly sensitive response (p = .010. However, in the TP53(- group taxane-platinum therapy possibly diminished the risk of death in patients over 53 yrs (p = .077. Among factors that positively interacted with taxane-platinum therapy in some analyses were endometrioid and clear cell type, FIGO III stage, bulky residual tumor, more advanced age of patient and moderate tumor differentiation. Conclusion Our results suggest that taxane-platinum therapy is particularly justified in patients with TP53(+ tumors or older

Platinum complexes of 5,6-Dihydroacenaphtho[5,6-cd]-1,2-dichalcogenoles

OpenAIRE

Benson, Callum G. M.; Schofield, Catherine M.; Randall, Rebecca A. M.; Wakefield, Lucy; Knight, Fergus R.; Slawin, Alexandra M. Z.; Woollins, J. Derek

2013-01-01

Six bis(phosphane) platinum complexes bearing dichalcogen acenaphthene ligands have been prepared by metathesis from cis-[PtCl2(PR3)(2)] (R-3 = Ph-3, Ph2Me, PhMe2) and the dilithium salts of the parent 5,6-dihydroacenaphtho[5,6-cd]-1,2-dichalcogenoles (AcenapE(2), L1 E = S, L2 E = Se). For their synthesis, the appropriate disulfide or diselenide species was treated with super hydride [LiBEt3H] to afford the dilithium salt by in situ reduction of the AcenapE(2) E-E bond. Further reaction, by m...

Selective hydrogenation of halogenated arenes using porous manganese oxide (OMS-2) and platinum supported OMS-2 catalysts.

Science.gov (United States)

McManus, Iain J; Daly, Helen; Manyar, Haresh G; Taylor, S F Rebecca; Thompson, Jillian M; Hardacre, Christopher

2016-07-04

Porous manganese oxide (OMS-2) and platinum supported on OMS-2 catalysts have been shown to facilitate the hydrogenation of the nitro group in chloronitrobenzene to give chloroaniline with no dehalogenation. Complete conversion was obtained within 2 h at 25 °C and, although the rate of reaction increased with increasing temperature up to 100 °C, the selectivity to chloroaniline remained at 99.0%. Use of Pd/OMS-2 or Pt/Al2O3 resulted in significant dechlorination even at 25 °C and 2 bar hydrogen pressure giving a selectivity to chloroaniline of 34.5% and 77.8%, respectively, at complete conversion. This demonstrates the potential of using platinum group metal free catalysts for the selective hydrogenation of halogenated aromatics. Two pathways were observed for the analogous nitrobenzene hydrogenation depending on the catalyst used. The hydrogenation of nitrobenzene was found to follow a direct pathway to aniline and nitrosobenzene over Pd/OMS-2 in contrast to the OMS and Pt/OMS-2 catalysts which resulted in formation of nitrosobenzene, azoxybenzene and azobenzene/hydrazobenzene intermediates before complete conversion to aniline. These results indicate that for Pt/OMS-2 the hydrogenation proceeds predominantly over the support with the metal acting to dissociate hydrogen. In the case of Pd/OMS-2 both the hydrogenation and hydrogen adsorption occur on the metal sites.

Novel non-platinum metal catalyst material

DEFF Research Database (Denmark)

2014-01-01

The present invention relates to a novel non-platinum metal catalyst material for use in low temperature fuel cells and electrolysers and to fuel cells and electrolysers comprising the novel non-platinum metal catalyst material. The present invention also relates to a novel method for synthesizing...... the novel non-platinum metal catalyst material....

One-step electrochemically-codeposited polyaniline-platinum for dye-sensitized solar cell applications

Energy Technology Data Exchange (ETDEWEB)

Thiangkaew, Anongnad; Keothongkham, Khamsone; Maiaugree, Wasan; Jarernboon, Wirat [Khon Kaen University, Khon Kaen (Thailand); Kamwanna, Teerasak; Pimanpang, Samuk; Amornkitbamrung, Vittaya [Khon Kaen University, Khon Kaen (Thailand); Nanotec-KKU Center of Excellence on Advanced Nanomaterials for Energy Production and Storage, Khon Kaen (Thailand)

2014-05-15

Platinum, polyaniline and composite polyaniline-platinum films were coated on conductive glass by using electrochemical deposition. They were then used as dye-sensitized solar cell counter electrodes. The efficiencies of platinum, polyaniline and composite polyaniline-platinum cells were 2.47, 4.47 and 6.62%, respectively. The improvement of composite polyaniline-platinum solar cell efficiency over pure polyaniline and platinum cells is because of an increase in the film's catalytic activity and a decrease in charge-transfer resistance between its counter electrode and electrolyte, as observed by using cyclic voltammogram and electrochemical impedance spectroscopy measurements, respectively. Co-deposition of polyaniline and Pt catalysts was confirmed by the presence of Pt and N peaks in the X-ray photoelectron spectroscopy spectrum.

Atomically flat platinum films grown on synthetic mica

Science.gov (United States)

Tanaka, Hiroyuki; Taniguchi, Masateru

2018-04-01

Atomically flat platinum thin films were heteroepitaxially grown on synthetic fluorophlogopite mica [KMg3(AlSi3O10)F2] by van der Waals epitaxy. Platinum films deposited on a fluorophlogopite mica substrate by inductively coupled plasma-assisted sputtering with oxygen introduction on a synthetic mica substrate resulted in the growth of twin single-crystalline epitaxial Pt(111) films.

Platinum catalyst formed on carbon nanotube by the in-liquid plasma method for fuel cell

Energy Technology Data Exchange (ETDEWEB)

Show, Yoshiyuki; Hirai, Akira; Almowarai, Anas; Ueno, Yutaro

2015-12-01

In-liquid plasma was generated in the carbon nanotube (CNT) dispersion fluid using platinum electrodes. The generated plasma spattered the surface of the platinum electrodes and dispersed platinum particles into the CNT dispersion. Therefore, the platinum nanoparticles were successfully formed on the CNT surface in the dispersion. The platinum nanoparticles were applied to the proton exchange membrane fuel cell (PEMFC) as a catalyst. The electrical power of 108 mW/cm{sup 2} was observed from the fuel cell which was assembled with the platinum catalyst formed on the CNT by the in-liquid plasma method. - Highlights: • The platinum catalyst was successfully formed on the CNT surface in the dispersion by the in-liquid plasma method. • The electrical power of 108 mW/cm{sup 2} was observed from the fuel cell which was assembled with the platinum catalyst formed on the CNT by the in-liquid plasma method.

Novel platinum black electroplating technique improving mechanical stability.

Science.gov (United States)

Kim, Raeyoung; Nam, Yoonkey

2013-01-01

Platinum black microelectrodes are widely used as an effective neural signal recording sensor. The simple fabrication process, high quality signal recording and proper biocompatibility are the main advantages of platinum black microelectrodes. When microelectrodes are exposed to actual biological system, various physical stimuli are applied. However, the porous structure of platinum black is vulnerable to external stimuli and destroyed easily. The impedance level of the microelectrode increases when the microelectrodes are damaged resulting in decreased recording performance. In this study, we developed mechanically stable platinum black microelectrodes by adding polydopamine. The polydopamine layer was added between the platinum black structures by electrodeposition method. The initial impedance level of platinum black only microelectrodes and polydopamine added microelectrodes were similar but after applying ultrasonication the impedance value dramatically increased for platinum black only microelectrodes, whereas polydopamine added microelectrodes showed little increase which were nearly retained initial values. Polydopamine added platinum black microelectrodes are expected to extend the availability as neural sensors.

Electrochemical and microstructural characterization of platinum supported on glassy carbon

Directory of Open Access Journals (Sweden)

Terzić Sanja

2007-01-01

Full Text Available The effect of the electrochemical oxidation of glassy carbon on the deposition of platinum particles and the electrocatalytic activity of platinum supported on oxidized glassy carbon were studied for methanol oxidation in H2SO4 solution. Platinum was potentiostatically deposited from H2SO4 + 6mM H2PtCl6 solution. Glassy carbon was anodically polarized in 1 M NaOH at 1.41 V (SCE for 35 and 95 s and in 0.5 M H2SO4 at 2V (SCE for 35; 95 s and 2.25 V for 35 and 95 s. Electrochemical treatment of the GC support leads to a better distribution of platinum on the substrate and has remarkable effect on the activity. The activity of the Pt/GCox electrode for methanol oxidation is larger than that of polycrystalline Pt and by more than one order of magnitude larger than that of a Pt/GC electrode. This increase in activity indicates the pronounced role of the organic residues of the GC support on the properties of Pt particles deposited on glassy carbon.

Photophysics of organometallic platinum(II) derivatives of the diketopyrrolopyrrole chromophore

KAUST Repository

Goswami, Subhadip; Winkel, Russell W.; Alarousu, Erkki; Ghiviriga, Ion; Mohammed, Omar F.; Schanze, Kirk S.

2014-01-01

A pair of diketopyrrolopyrrole (DPP) chromophores that are end-functionalized with platinum containing "auxochromes" were subjected to electrochemical and photophysical study. The chromophores contain either platinum acetylide or ortho-metalated 2-thienylpyridinyl(platinum) end-groups (DPP-Pt(CC) and DPP-Pt(acac), respectively). The ground state redox potentials of the chromophores were determined by solution electrochemistry, and the HOMO and LUMO levels were estimated. The chromophores' photophysical properties were characterized by absorption, photoluminescence, and time-resolved absorption spectroscopy on time scales from sub-picoseconds to microseconds. Density functional theory (DFT) computations were performed to understand the molecular orbitals involved in both the singlet and triplet excited state photophysics. The results reveal that in both platinum DPP derivatives the organometallic auxochromes have a significant effect on the chromophores' photophysics. The most profound effect is a reduction in the fluorescence yields accompanied by enhanced triplet yields due to spin-orbit coupling induced by the metal centers. The effects are most pronounced in DPP-Pt(acac), indicating that the orthometalated platinum auxochrome is able to induce spin-orbital coupling to a greater extent compared to the platinum acetylide units. (Figure Presented).

In vitro permeation of platinum and rhodium through Caucasian skin.

Science.gov (United States)

Franken, A; Eloff, F C; Du Plessis, J; Badenhorst, C J; Jordaan, A; Du Plessis, J L

2014-12-01

During platinum group metals (PGMs) refining the possibility exists for dermal exposure to PGM salts. The dermal route has been questioned as an alternative route of exposure that could contribute to employee sensitisation, even though literature has been focused on respiratory exposure. This study aimed to investigate the in vitro permeation of platinum and rhodium through intact Caucasian skin. A donor solution of 0.3mg/ml of metal, K2PtCl4 and RhCl3 respectively, was applied to the vertical Franz diffusion cells with full thickness abdominal skin. The receptor solution was removed at various intervals during the 24h experiment, and analysed with high resolution ICP-MS. Skin was digested and analysed by ICP-OES. Results indicated cumulative permeation with prolonged exposure, with a significantly higher mass of platinum permeating after 24h when compared to rhodium. The mass of platinum retained inside the skin and the flux of platinum across the skin was significantly higher than that of rhodium. Permeated and skin retained platinum and rhodium may therefore contribute to sensitisation and indicates a health risk associated with dermal exposure in the workplace. Copyright © 2014 Elsevier Ltd. All rights reserved.

Photophysics of organometallic platinum(II) derivatives of the diketopyrrolopyrrole chromophore

KAUST Repository

Goswami, Subhadip

2014-12-18

A pair of diketopyrrolopyrrole (DPP) chromophores that are end-functionalized with platinum containing "auxochromes" were subjected to electrochemical and photophysical study. The chromophores contain either platinum acetylide or ortho-metalated 2-thienylpyridinyl(platinum) end-groups (DPP-Pt(CC) and DPP-Pt(acac), respectively). The ground state redox potentials of the chromophores were determined by solution electrochemistry, and the HOMO and LUMO levels were estimated. The chromophores\\' photophysical properties were characterized by absorption, photoluminescence, and time-resolved absorption spectroscopy on time scales from sub-picoseconds to microseconds. Density functional theory (DFT) computations were performed to understand the molecular orbitals involved in both the singlet and triplet excited state photophysics. The results reveal that in both platinum DPP derivatives the organometallic auxochromes have a significant effect on the chromophores\\' photophysics. The most profound effect is a reduction in the fluorescence yields accompanied by enhanced triplet yields due to spin-orbit coupling induced by the metal centers. The effects are most pronounced in DPP-Pt(acac), indicating that the orthometalated platinum auxochrome is able to induce spin-orbital coupling to a greater extent compared to the platinum acetylide units. (Figure Presented).

Protein phosphatase 2A inhibition and circumvention of cisplatin cross-resistance by novel TCM-platinum anticancer agents containing demethylcantharidin.

Science.gov (United States)

To, Kenneth K W; Wang, Xinning; Yu, Chun Wing; Ho, Yee-Ping; Au-Yeung, Steve C F

2004-09-01

Novel TCM-platinum compounds [Pt(C(8)H(8)O(5))(NH(2)R)(2)] 1-5, derived from integrating demethylcantharidin, a modified component from a traditional Chinese medicine (TCM) with a platinum moiety, possess anticancer and protein phosphatase 2A inhibition properties. The compounds are able to circumvent cisplatin resistance by apparently targeting the DNA repair mechanism. Novel isosteric analogues [Pt(C(9)H(10)O(4))(NH(2)R)(2)] A and B, devoid of PP2A-inhibitory activity, were found to suffer from an enhanced DNA repair and were cross-resistant to cisplatin. The results advocate a well-defined structure-activity requirement associating the PP2A-inhibiting demethylcantharidin with the circumvention of cisplatin cross-resistance demonstrated by TCM-Pt compounds 1-5.

Platinum single crystal electrodes for the electrocatalysis of methane oxidation

Directory of Open Access Journals (Sweden)

Mayara Munaretto

2011-03-01

Full Text Available The main objective of this paper is to characterize the voltammetric profiles of platinum single crystals of low Miller indexes Pt(100 and Pt(110 and study their catalytic activities on the oxidation of methane. In this way, it was developed a metallic surface modified by presence of other metal oxide, which presents catalytic activity for this reaction. It is well known that the electrooxidation of methane (CH4 leads mainly to the formation of CO2 and H2O, however, the oxidation can also lead to the formation of CO, a reaction intermediate that has strong interaction with metal surfaces, such as platinum. This molecule tends to accumulate on the platinum surface and to passive it, due to the self-poisoning, decreasing its catalytic activity. Therefore, the main aim of this work was the development of a platinum electrode modified by deposition of titanium oxide, which presented electrocatalytic properties for the oxidation of methane.

Synthesis and reactivity towards diiodine of palladium(II) and platinum(II) complexes with non-cyclic and cyclic ligands (C6H3{CH=NR1R2}2-2,6)-. End-on diiodine-platinum(II) bonding in macrocyclic [PtI(C6H3{CH2NMe(CH2)7MeNCH2}-2,6)(h1-I2)

NARCIS (Netherlands)

Koten, G. van; Beek, J.A.M. van; Dekker, G.P.C.M.; Wissing, E.; Zoutberg, M.C.; Stam, C.H.

1990-01-01

Several new organo-platinum(II) and -palladium(II) complexes [MX(C{6}H{3}{CH{2}NR}1{R}2{}{2}-2, 6)] (X = halide, M = Pt, Pd; R}1{ = R}2{ = Et; R}2{ = Me, R}1{ = }t{Bu, M = Pt: R}2{ = Me, R}1{ = Ph) have been synthesized from [PtCl{2}(SEt{2}){2}] or [PdCl{2}(COD)] (COD = 1, 5-cyclooctadiene) by

BOWIEITE: A NEW RHODIUM-IRIDIUM-PLATINUM SULFIDE IN PLATINUM-ALLOY NUGGETS, GOODNEWS BAY, ALASKA.

Science.gov (United States)

Desborough, George A.; Criddle, Alan J.

1984-01-01

Bowieite (Rh,Ir,Pt)//2S//3, a new mineral species, is found in three nuggets of platinum from Goodnews Bay, Alaska. In linearly polarized reflected light, and compared to the host, higher reflecting white platinum-iridium alloy, bowieite is pale gray to pale gray-brown; neither bireflectance nor reflectance pleochroism is apparent. With polars crossed, its anisotropic rotation tints vary from gray to dark brown. Luminance values (relative to the CIE illuminant C) for R//1 and R//2, computed from full spectral data for the most bireflectant grain, are 45. 8% and 48. 2% in air, and 30. 5% and 33. 0% in oil, respectively. VHN//1//0//0 1288 (858 to 1635). Bowieite is orthorhombic, space group Pnca, with a 8. 454(7) -8. 473(8), b 5. 995(1)-6. 002(7), c 6. 143(1)-6. 121(8) A, Z equals 4. Some grains that are 2. 6 to 3. 8 atomic % metal-deficient occur as an optically coherent rim on bowieite; the rim and the bowieite grain are not optically continuous.

Exosomes as mediators of platinum resistance in ovarian cancer.

Science.gov (United States)

Crow, Jennifer; Atay, Safinur; Banskota, Samagya; Artale, Brittany; Schmitt, Sarah; Godwin, Andrew K

2017-02-14

Exosomes have been implicated in the cell-cell transfer of oncogenic proteins and genetic material. We speculated this may be one mechanism by which an intrinsically platinum-resistant population of epithelial ovarian cancer (EOC) cells imparts its influence on surrounding tumor cells. To explore this possibility we utilized a platinum-sensitive cell line, A2780 and exosomes derived from its resistant subclones, and an unselected, platinum-resistant EOC line, OVCAR10. A2780 cells demonstrate a ~2-fold increase in viability upon treatment with carboplatin when pre-exposed to exosomes from platinum-resistant cells as compared to controls. This coincided with increased epithelial to mesenchymal transition (EMT). DNA sequencing of EOC cell lines revealed previously unreported somatic mutations in the Mothers Against Decapentaplegic Homolog 4 (SMAD4) within platinum-resistant cells. A2780 cells engineered to exogenously express these SMAD4 mutations demonstrate up-regulation of EMT markers following carboplatin treatment, are more resistant to carboplatin, and release exosomes which impart a ~1.7-fold increase in resistance in naive A2780 recipient cells as compared to controls. These studies provide the first evidence that acquired SMAD4 mutations enhance the chemo-resistance profile of EOC and present a novel mechanism in which exchange of tumor-derived exosomes perpetuates an EMT phenotype, leading to the development of subpopulations of platinum-refractory cells.

Electrochemical and SEM studies of tetra-ammine platinum (II) (Pt(NH3)4)(OH)2 solution

International Nuclear Information System (INIS)

Wan Jeffrey Basirun

2002-01-01

Electrochemical studies include cyclic voltammetry with microelectrodes were done on a solution of tetra-ammine platinum (II) (Pt(NH 3 ) 4 )(OH) 2 at pH 13 and showed that the electrochemical reduction of this compound was no different from the tetra-ammine platinum (II) (Pt(NH 3 ) 4 )(HPO 4 ) at pH 10.4. The solution was instable to high temperatures and results have shown that electroplating can be done at a limited temperature range for longer periods of time or at higher temperatures for short periods of time. Scanning electron microscopy was done on some of the constant current electrodeposited samples at high temperatures and result obtained was satisfactory. (Authors)

Microstructural Study on Oxidation Resistance of Nonmodified and Platinum Modified Aluminide Coating

Science.gov (United States)

Zagula-Yavorska, Maryana; Sieniawski, Jan

2014-03-01

Platinum electroplating layers (3 and 7 μm thick) were deposited on the surface of the Inconel 713 LC, CMSX 4, and Inconel 625 Ni-base superalloys. Diffusion treatment at 1050°C for 2 h under argon atmosphere was performed after electroplating. Diffusion treated samples were aluminized according to the low activity CVD process at 1050°C for 8 h. The nonmodified aluminide coatings consist of NiAl phase. Platinum modification let to obtain the (Ni,Pt)Al phase in coatings. The coated samples were subjected to cyclic oxidation testing at 1100°C. It was discovered that increase of the platinum electroplating thickness from 3 to 7 μm provides the improvement of oxidation resistance of aluminide coatings. Increase of the platinum thickness causes decreases in weight change and decreases in parabolic constant during oxidation. The platinum provides the pure Al2O3 oxide formation, slow growth oxide layer, and delay the oxide spalling during heating-cooling thermal cycles.

The molecular interactions in the extraction system: acetylacetone-InCl3-water

International Nuclear Information System (INIS)

Kulawik, I.; Bogon, E.

1978-01-01

The extraction process in the chelate system: acetylacetone-InCl 3 -Water and possibility of the investigations of some physico-chemical properties of this system were discussed. The preliminary measurements for determination the adsorption kinetics and the equilibrium in the system were presented. Also extraction coefficient of indium salt was determined. The results of the principal measurements of the surface and interfacial tension as a function of concentration and temperature in the phases were presented. The measurements were done in different conditions when the both phases were in contact during the same time but in the various temperature. The experimental data served also for the calculation of the work of cohesion and adhesion in the system. The entropy and surface energy of the particular phases of the system were also determined. (author)

Activation analysis for platinum in gold and metals of the platinum group through 199Au

International Nuclear Information System (INIS)

Foerster, H.

1976-01-01

Platinum was determined in gold and in metals of the platinum group through 199 Au by activation analysis. The matrix was separated at the end of irradiation before the daughter nuclide was formed. Gold was separated by extraction with MIBK from 1

Efficient organic light-emitting devices with platinum-complex emissive layer

KAUST Repository

Yang, Xiaohui

2011-01-18

We report efficient organic light-emitting devices having a platinum-complex emissive layer with the peak external quantum efficiency of 17.5% and power efficiency of 45 lm W−1. Variation in the device performance with platinum-complex layer thickness can be attributed to the interplay between carrier recombination and intermolecular interactions in the layer. Efficient white devices using double platinum-complex layers show the external quantum efficiency of 10%, the Commission Internationale d’Énclairage coordinates of (0.42, 0.41), and color rendering index of 84 at 1000 cd m−2.

Efficient organic light-emitting devices with platinum-complex emissive layer

KAUST Repository

Yang, Xiaohui; Wu, Fang-Iy; Haverinen, Hanna; Li, Jian; Cheng, Chien-Hong; Jabbour, Ghassan E.

2011-01-01

We report efficient organic light-emitting devices having a platinum-complex emissive layer with the peak external quantum efficiency of 17.5% and power efficiency of 45 lm W−1. Variation in the device performance with platinum-complex layer thickness can be attributed to the interplay between carrier recombination and intermolecular interactions in the layer. Efficient white devices using double platinum-complex layers show the external quantum efficiency of 10%, the Commission Internationale d’Énclairage coordinates of (0.42, 0.41), and color rendering index of 84 at 1000 cd m−2.

Low platinum catalyst and method of preparation

Energy Technology Data Exchange (ETDEWEB)

Liu, Di-Jia; Chong, Lina

2017-11-21

A low platinum catalyst and method for making same. The catalyst comprises platinum-transition metal bimetallic alloy microcrystallites over a transition metal-nitrogen-carbon composite. A method of making a catalyst comprises preparation of transition metal organic frameworks, infusion of platinum, thermal treatment, and reduction to form the microcrystallites and composite.

Niraparib Maintenance Therapy in Platinum-Sensitive, Recurrent Ovarian Cancer

DEFF Research Database (Denmark)

Mirza, Mansoor R; Monk, Bradley J; Herrstedt, Jørn

2016-01-01

Background Niraparib is an oral poly(adenosine diphosphate [ADP]-ribose) polymerase (PARP) 1/2 inhibitor that has shown clinical activity in patients with ovarian cancer. We sought to evaluate the efficacy of niraparib versus placebo as maintenance treatment for patients with platinum-sensitive, ......Background Niraparib is an oral poly(adenosine diphosphate [ADP]-ribose) polymerase (PARP) 1/2 inhibitor that has shown clinical activity in patients with ovarian cancer. We sought to evaluate the efficacy of niraparib versus placebo as maintenance treatment for patients with platinum...... or 4 adverse events that were reported in the niraparib group were thrombocytopenia (in 33.8%), anemia (in 25.3%), and neutropenia (in 19.6%), which were managed with dose modifications. Conclusions Among patients with platinum-sensitive, recurrent ovarian cancer, the median duration of progression...

Platinum redispersion on metal oxides in low temperature fuel cells.

Science.gov (United States)

Tripković, Vladimir; Cerri, Isotta; Nagami, Tetsuo; Bligaard, Thomas; Rossmeisl, Jan

2013-03-07

We have analyzed the aptitude of several metal oxide supports (TiO(2), SnO(2), NbO(2), ZrO(2), SiO(2), Ta(2)O(5) and Nb(2)O(5)) to redisperse platinum under electrochemical conditions pertinent to the Proton Exchange Membrane Fuel Cell (PEMFC) cathode. The redispersion on oxide supports in air has been studied in detail; however, due to different operating conditions it is not straightforward to link the chemical and the electrochemical environment. The largest differences reflect in (1) the oxidation state of the surface (the oxygen species coverage), (2) temperature and (3) the possibility of platinum dissolution at high potentials and the interference of redispersion with normal working potential of the PEMFC cathode. We have calculated the PtO(x) (x = 0, 1, 2) adsorption energies on different metal oxides' surface terminations as well as inside the metal oxides' bulk, and we have concluded that NbO(2) might be a good support for platinum redispersion at PEMFC cathodes.

Redeposition of electrochemically dissolved platinum as nanoparticles on carbon

DEFF Research Database (Denmark)

Norgaard, C. F.; Stamatin, S. N.; Skou, E. M.

2014-01-01

communication reports a simple chemical method for reprecipitating platinum as nanoparticles of reasonable particle size on a carbon substrate without intermediary separation and handling of solid platinum salt. After electrochemical dissolution, platinum was reprecipitated using a polyol based method. Platinum...

Strategies for the fabrication of porous platinum electrodes

Energy Technology Data Exchange (ETDEWEB)

Kloke, Arne; Stetten, Felix von; Kerzenmacher, Sven [Laboratory for MEMS Applications, Department of Microsystems Engineering-IMTEK, University of Freiburg, Freiburg (Germany); Zengerle, Roland [Laboratory for MEMS Applications, Department of Microsystems Engineering-IMTEK, University of Freiburg, Freiburg (Germany); BIOSS Centre for Biological Signalling Studies, Albert-Ludwigs-Universitaet Freiburg (Germany)

2011-11-16

Porous platinum is of high technological importance due to its various applications in fuel cells, sensors, stimulation electrodes, mechanical actuators and catalysis in general. Based on a discussion of the general principles behind the reduction of platinum salts and corresponding deposition processes this article discusses techniques available for platinum electrode fabrication. The numerous, different strategies available to fabricate platinum electrodes are reviewed and discussed in the context of their tuning parameters, strengths and weaknesses. These strategies comprise bottom-up approaches as well as top-down approaches. In bottom-up approaches nanoparticles are synthesized in a first step by chemical, photochemical or sonochemical means followed by an electrode formation step by e.g. thin film technology or network formation to create a contiguous and conducting solid electrode structure. In top-down approaches fabrication starts with an already conductive electrode substrate. Corresponding strategies enable the fabrication of substrate-based electrodes by e.g. electrodeposition or the fabrication of self-supporting electrodes by dealloying. As a further top-down strategy, this review describes methods to decorate porous metals other than platinum with a surface layer of platinum. This way, fabrication methods not performable with platinum can be applied to the fabrication of platinum electrodes with the special benefit of low platinum consumption. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Adenosine triphosphate-based chemotherapy response assay (ATP-CRA)-guided platinum-based 2-drug chemotherapy for unresectable nonsmall-cell lung cancer.

Science.gov (United States)

Moon, Yong Wha; Choi, Sung Ho; Kim, Yong Tai; Sohn, Joo Hyuk; Chang, Joon; Kim, Se Kyu; Park, Moo Suk; Chung, Kyung Young; Lee, Hyoun Ju; Kim, Joo-Hang

2007-05-01

The study investigated correlations between adenosine triphosphate / chemotherapy response assay (ATP-CRA) and clinical outcomes after ATP-CRA-guided platinum-based chemotherapy for unresectable nonsmall-cell lung cancer (NSCLC). The authors performed an in vitro chemosensitivity test, ATP-CRA, to evaluate the chemosensitivities of anticancer drugs such as cisplatin, carboplatin, paclitaxel, docetaxel, gemcitabine, and vinorelbine for chemonaive, unresectable NSCLC. The cell death rate was determined by measuring the intracellular ATP levels of drug-exposed cells compared with untreated controls. A sensitive drug was defined as a drug producing 30% or more reduction in ATP compared with untreated controls. Assay-guided platinum-based 2-drug chemotherapy was given to patients with pathologically confirmed NSCLC. Thirty-four patients were enrolled. Thirty tumor specimens were obtained by bronchoscopic biopsies and 4 obtained surgically. The median age was 61 years and 27 patients had an Eastern Cooperative Oncology Group (ECOG) performance status of 0-1. The response rate was 43.8%. At a median follow-up period of 16.9 months, the median progression-free and overall survivals were 3.6 and 11.2 months, respectively. Patients were dichotomized into the platinum-sensitive (S; 20 patients) and resistant (R; 14 patients) groups. The positive/negative predictive values were 61.1% and 78.6% with a predictive accuracy of 68.8%. Although without significant differences in pretreatment parameters, the S-group showed better clinical response (P=.036), longer progression-free survival (P=.060), and longer overall survival (P=.025). Despite using bronchoscopic biopsied specimens, ATP-CRA and clinical outcomes correlated well after assay-guided platinum-based 2-drug chemotherapy for unresectable NSCLC. There was a favorable response and survival in the platinum-sensitive vs resistant groups. Copyright (c) 2007 American Cancer Society

Platinum recycling in the United States in 1998

Science.gov (United States)

Hilliard, Henry E.

2001-01-01

In the United States, catalytic converters are the major source of secondary platinum for recycling. Other sources of platinum scrap include reforming and chemical process catalysts. The glass industry is a small but significant source of platinum scrap. In North America, it has been estimated that in 1998 more than 20,000 kilograms per year of platinum-group metals from automobile catalysts were available for recycling. In 1998, an estimated 7,690 kilograms of platinum were recycled in the United States. U.S. recycling efficiency was calculated to have been 76 percent in 1998; the recycling rate was estimated at 16 percent.

Preparation and characterization of Fe{sub 3}O{sub 4}-Pt nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Andrade, Ângela Leão, E-mail: angelala01@hotmail.com [Federal University of Ouro Preto (UFOP), Department of Chemistry, ICEB (Brazil); Cavalcante, Luis Carlos Duarte [Federal University of Piauí (UFPI), Center of Natural Sciences (Brazil); Fabris, José Domingos [Federal University of Minas Gerais (UFMG), Department of Chemistry, ICEx (Brazil); Pereira, Márcio César [Federal University of the Jequitinhonha and Mucuri Valleys (UFVJM), Institute of Science, Engineering and Technology (Brazil); Ardisson, José Domingos [Center for the Development of the Nuclear Technology (CDTN), Laboratory of Applied Physics (Brazil); Domingues, Rosana Zacarias [Federal University of Minas Gerais (UFMG), Department of Chemistry, ICEx (Brazil)

2017-11-15

Pt and Pt-based nanomaterials are active anticancer drugs for their ability to inhibit the division of living cells. Nanoparticles of magnetite containing variable proportions of platinum were prepared in the laboratory. The magnetite nanoparticles with platinum (Pt-Fe{sub 3}O{sub 4}) were obtained by reducing the Fe{sup 3+} of the maghemite (γ Fe{sub 2}O{sub 3}) mixed with platinum (II) acetylacetonate and sucrose in two inversely coupled ceramic crucibles and heated in a furnace at 400 °C for 20 min. The formed carbon during this preparation acts to chemically reduce the ferric iron in maghemite. Moreover, its residual layer on the particle surface prevents the forming magnetite from oxidizing in air and helps retain the platinum in the solid mixture. The produced Pt-magnetite samples were characterized by {sup 57}Fe-Mössbauer spectroscopy, powder X-ray diffraction, scanning electron microscopy, and magnetization measurements. Measurements of AC magnetic-field-induced heating properties of the obtained nanocomposites, in aqueous solution, showed that they are suitable as a hyperthermia agent for biological applications.

Synthesis, crystal structure and anticancer activity of tetrakis(N-isopropylimidazolidine-2-selenone)platinum(II) chloride

Science.gov (United States)

Ahmad, Saeed; Altoum, Ali Osman S.; Vančo, Ján; Křikavová, Radka; Trávníček, Zdeněk; Dvořák, Zdeněk; Altaf, Muhammad; Sohail, Manzar; Isab, Anvarhusein A.

2018-01-01

A Platinum(II) complex of N-isopropylimidazolidine-2-selenone (i-PrImSe), [Pt(i-PrImSe)4]Cl2 (1) was prepared and characterized by elemental analysis, IR and NMR (1H, 13C, 77Se &195Pt) spectroscopy, and X-ray crystallography. The structure of 1 consists of [Pt(i-PrImSe)4]2+ complex ion and chloride counter ions. The platinum(II) atom adopts a distorted square planar geometry. The in vitro antitumor activity of 1 as well as cisplatin, was evaluated by MTT assay against human; ovarian carcinoma A2780 and its cisplatin-resistant subline A2780R, prostate cancer 22Rv1 and breast cancer MCF-7 cell lines. The title complex displayed the activity against the A2780 cells (IC50 = 30.8 μM) at the level comparable to cisplatin (IC50 = 26.8 μM). The interaction studies with sulfur-containing biomolecules revealed its ability to form a variety of intermediates and oxidized species with L-cysteine and reduced glutathione.

Superficial characterization and zircaloy-2 electrochemistry with hydrothermal deposit of platinum; Caracterizacion superficial y electroquimica de zircaloy-2 con deposito hidrotermal de platino

Energy Technology Data Exchange (ETDEWEB)

Contreras R, A.; Arganis J, C. R.; Medina A, A. L. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Gris C, M. M., E-mail: aida.contreras@inin.gob.mx [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Carretera Cardel-Nautla Km 42.5, Alto Lucero, Veracruz (Mexico)

2011-11-15

The combustible elements of the boiling water nuclear reactors (BWR) are formed by zircaloy-2 tubes that contain in their interior UO{sub 2} pellets. With the objective of mitigating the speed of crack growth by IGSCC to a minimum negative impact on the BWR operation, General Electric developed the noble metals chemical addition (NMCA), in where noble metals particles as Pt, Pd, and Rh, are deposited on the surface of the metal to catalyze the recombination of H{sub 2} and O{sub 2}. Hydrogen is also injected to have it in excess and to favor this recombination (HWC) and zinc to reduce dose. In this work was oxidized zircaloy-2 low similar conditions to the HWC, platinum was deposited starting from a solution of Na{sub 2}Pt(OH){sub 6} with 30 ppm of Pt, in refined samples and without polishing, they were characterized by scanning electron microscopy, energy dispersed spectroscopy, XPS and electrochemistry, by means of Tafel curves and cyclical polarization. On the zircaloy surface was found a ZrO{sub 2} layer that remains under the different study conditions. Under HWC conditions is the oxides formation, possibly complex oxides of zirconium, iron and tin. After the platinum deposit these oxides decrease forming the sub-oxides: Zr{sub 2}O, Zr O, Zr{sub 2}O{sub 3}. The Tafel curves indicates the reduction of the oxygen of the sample with platinum and the cyclical polarization curves show that the reactions that happen on the zircaloy electrodes are not dur to located corrosion. (Author)

Ligand substitution and selective surface coordination studies of iodine and 2,5-dihydroxythiophenol at platinum electrodes

International Nuclear Information System (INIS)

Berry, G.M.; Soriaga, M.P.

1989-01-01

The relative surface coordination strengths of 2,5-dihydroxythiophenol (DHT) and iodine at a smooth polycrystalline platinum electrode have been investigated by thin-layer electrochemical techniques. The competitive chemisorption was studied by exposing the Pt electrode to solutions of varying mole fractions of I and DHT. Studies of ligand substitution were carried out by the introduction of an iodine-coated Pt electrode into DHT solutions, and the introduction of a DHT-coated into I solutions. Surface coverage measurements indicated that DHT is preferentially adsorbed and will displace chemisorbed iodine at the Pt electrode. Chemisorbed DHT is not appreciably displaced by iodine. These results and their contribution to the trend in the selective surface coordination chemistry of platinum electrodes will be discussed

Flow Injection Analysis with Electrochemical Detection for Rapid Identification of Platinum-Based Cytostatics and Platinum Chlorides in Water

Directory of Open Access Journals (Sweden)

Marketa Kominkova

2014-02-01

Full Text Available Platinum-based cytostatics, such as cisplatin, carboplatin or oxaliplatin are widely used agents in the treatment of various types of tumors. Large amounts of these drugs are excreted through the urine of patients into wastewaters in unmetabolised forms. This phenomenon leads to increased amounts of platinum ions in the water environment. The impacts of these pollutants on the water ecosystem are not sufficiently investigated as well as their content in water sources. In order to facilitate the detection of various types of platinum, we have developed a new, rapid, screening flow injection analysis method with electrochemical detection (FIA-ED. Our method, based on monitoring of the changes in electrochemical behavior of analytes, maintained by various pH buffers (Britton-Robinson and phosphate buffer and potential changes (1,000, 1,100 and 1,200 mV offers rapid and cheap selective determination of platinum-based cytostatics and platinum chlorides, which can also be present as contaminants in water environments.

Platinum-induced structural collapse in layered oxide polycrystalline films

International Nuclear Information System (INIS)

Wang, Jianlin; Liu, Changhui; Huang, Haoliang; Fu, Zhengping; Peng, Ranran; Zhai, Xiaofang; Lu, Yalin

2015-01-01

Effect of a platinum bottom electrode on the SrBi 5 Fe 1−x Co x Ti 4 O 18 layered oxide polycrystalline films was systematically studied. The doped cobalt ions react with the platinum to form a secondary phase of PtCoO 2 , which has a typical Delafossite structure with a weak antiferromagnetism and an exceptionally high in-plane electrical conductivity. Formation of PtCoO 2 at the interface partially consumes the cobalt dopant and leads to the structural collapsing from 5 to 4 layers, which was confirmed by X-ray diffraction and high resolution transmission electron microscopy measurements. Considering the weak magnetic contribution from PtCoO 2 , the observed ferromagnetism should be intrinsic of the Aurivillius compounds. Ferroelectric properties were also indicated by the piezoresponse force microscopy. In this work, the platinum induced secondary phase at the interface was observed, which has a strong impact on Aurivillius structural configuration and thus the ferromagnetic and ferroelectric properties

Isolation of homoleptic platinum oxyanionic complexes with doubly protonated diazacrown cation

Science.gov (United States)

Vasilchenko, Danila; Tkachev, Sergey; Baidina, Iraida; Romanenko, Galina; Korenev, Sergey

2017-02-01

Doubly protonated diazacrown ether cation (1,4,10,13-tetraoxa-7,16-diazoniacyclooctadecane DCH22+) was used for the efficient isolation of the homoleptic platinum complexes [Pt(NO3)6]2- and [Pt(C2O4)2]2- to crystalline solid phases from solutions containing mixtures of related platinum complexes. DCH22+ molecules in nitric acid solution were shown to prevent the condensation of mononuclear [Pt(H2O)n(NO3)6-n]n-2 species.

Multi-wall carbon nanotubes supported molybdenyl acetylacetonate: Efficient and highly reusable catalysts for epoxidation of alkenes with tert-butyl hydroperoxide

International Nuclear Information System (INIS)

Esnaashari, Fariba; Moghadam, Majid; Mirkhani, Valiollah; Tangestaninejad, Shahram; Mohammadpoor-Baltork, Iraj; Khosropour, Ahmad Reza; Zakeri, Maryam

2012-01-01

Efficient epoxidation of olefins catalyzed by MoO 2 (acac) 2 supported on amines functionalized MWCNTs is reported. The MWCNTs bearing carboxylic acid groups were modified with 2-aminophenol and 2-aminothiophenol. These amine–MWCNTs act as bidentate ligand for attachment of Mo catalyst. These catalysts were characterized by elemental analysis, scanning electron microscopy, FT-IR and diffuse reflectance UV–Vis spectroscopic methods. The prepared catalysts were used for efficient epoxidation of different alkenes such as cyclic and linear ones with tert-butyl hydroperoxide in refluxing 1,2-dichloroethane. These heterogeneous catalysts can be reused several times without significant loss of their catalytic activity. Highlights: ► Supporting of molybdenyl acetylacetonate on amine-modified MWCNTs. ► Heterogeneous catalysts were prepared. ► These catalysts were highly efficient in the epoxidation of alkenes with TBHP. ► Makes the catalysts reusable.

The effects of thermal-neutron irradiation on platinum and dilute platinum-gold alloys

International Nuclear Information System (INIS)

Piani, C.S.B.

1978-12-01

The effect of varying defect concentrations on the recovery spectrum of thermal-neutron-irradiated pure platinum after isochronal anneals was investigated. The dose-independence of substages I(A), I(B) and I(C), and the dose dependence of substage I(D) and I(E), were observed to be in agreement with electron-irradiated studies. The 120 K substage in pure platinum was shown not to be due to interstitial-interstitial reactions, but could possibly be accounted for in terms of detrapping of interstitials from impurities or intrinsic immobile defects. The 360 K stage was shown to shift and was suppressed with increasing defect concentration. The possible conversion of the crowdion to a dumbbell near 160 K in Stage ll in platinum, as predicted by the two-interstitial model, was investigated by consideration of the initial slopes of the production curves between 80 K and 300 K. A minimum in these slopes was observed near 160 K and could be interpreted as due to the conversion of the highly mobile crowdion to an immobile dumbbell at this temperature. The influence of varying gold concentrations on the recovery spectrum of platinum was investigated in dilute platinum-gold alloys. The characteristics of several additional substages in Stage ll, due to the gold alloying were comparable to the results of electron-irradiation experiments. The observations made with regard to the impurity (gold) dependence of these substages could be interpreted in terms of the concentrations of the interstitials, vacancies and impurities present in the material. The interpretation of these substages was found to be consistent, if the recovery spectrum was investigated as a function of defect concentration [af

Speciation of platinum(IV) in nitric acid solutions.

Science.gov (United States)

Vasilchenko, Danila; Tkachev, Sergey; Baidina, Iraida; Korenev, Sergey

2013-09-16

The speciation of platinum(IV) ions in nitric acid (6-15.8 M) solutions of H2[Pt(OH)6] has been studied by (195)Pt NMR and Raman spectroscopy. Series of aqua-hydroxo-nitrato complexes [Pt(L)(x)(NO3)(6-x)] (L = H2O or OH(-); x = 0, ..., 6) were found to exist in such solutions. The pair additivity model of chemical shifts and statistical theory were used to assign signals in NMR spectra to particular [Pt(L)(x)(NO3)(6-x)] species. Mononuclear hexanitratoplatinates(IV) have been isolated in solid state in substantial yield as pyridinium salt (PyH)2[Pt(NO3)6] and characterized by single-crystal X-ray diffraction. Aging of the platinum nitric acid solutions for more than 5-6 h results in oligomerization of [Pt(L)(x)(NO3)(6-x)] species and the formation of oligonuclear aqua-hydroxo-nitrato complexes with OH(-) and NO3(-) bridging ligands. Oligomeric platinum(IV) complexes with two and four nuclei were unambiguously detected by NMR on (195)Pt -enriched samples. Oligomers with even higher nuclearity were also detected. Dimeric anions [Pt2(μ-OH)2(NO3)8](2-) have been isolated as single crystals of tetramethylammonium salt and characterized by X-ray diffraction.

Cerium oxide and platinum nanoparticles protect cells from oxidant-mediated apoptosis

International Nuclear Information System (INIS)

Clark, Andrea; Zhu Aiping; Sun Kai; Petty, Howard R.

2011-01-01

Catalytic nanoparticles represent a potential clinical approach to replace or correct aberrant enzymatic activities in patients. Several diseases, including many blinding eye diseases, are promoted by excessive oxidant stress due to reactive oxygen species (ROS). Cerium oxide and platinum nanoparticles represent two potentially therapeutic nanoparticles that de-toxify ROS. In the present study, we directly compare these two classes of catalytic nanoparticles. Cerium oxide and platinum nanoparticles were found to be 16 ± 2.4 and 1.9 ± 0.2 nm in diameter, respectively. Using surface plasmon-enhanced microscopy, we find that these nanoparticles associate with cells. Furthermore, cerium oxide and platinum nanoparticles demonstrated superoxide dismutase catalytic activity, but did not promote hemolytic or cytolytic pathways in living cells. Importantly, both cerium oxide and platinum nanoparticles reduce oxidant-mediated apoptosis in target cells as judged by the activation of caspase 3. The ability to diminish apoptosis may contribute to maintaining healthy tissues.

On the enzymatic formation of platinum nanoparticles

International Nuclear Information System (INIS)

Govender, Y.; Riddin, T. L.; Gericke, M.; Whiteley, C. G.

2010-01-01

A dimeric hydrogenase enzyme (44.5 and 39.4 kDa sub units) was isolated in a 39.5% yield from the fungus Fusarium oxysporum and purified 4.64-fold by ion exchange chromatography on Sephacryl S-200. Characterisation of the enzyme afforded pH and temperature optima of 7.5 and 38 o C, respectively, a half-life stability of 36 min and a V max and K m of 3.57 nmol min -1 mL -1 and 2.25 mM, respectively. This enzyme was inhibited (non-competitively) by hydrogen hexachloroplatinic acid (H 2 PtCl 6 ) at 1 or 2 mM with a K i value of 118 μM. Incubation of the platinum salt with the pure enzyme under an atmosphere of hydrogen and optimum enzyme conditions (pH 7.5, 38 o C) afforded o C) over 90% reduction took place after the same length of time. Cell-free extract from the fungal isolates produced nearly 90% bioreduction of the platinum salt under both pH and temperature conditions. The bioreduction of the platinum salt by a hydrogenase enzyme takes place by a passive process and not an active one as previously understood.

Electrical Discharge Platinum Machining Optimization Using Stefan Problem Solutions

Directory of Open Access Journals (Sweden)

I. B. Stavitskiy

2015-01-01

Full Text Available The article presents the theoretical study results of platinum workability by electrical discharge machining (EDM, based on the solution of the thermal problem of moving the boundary of material change phase, i.e. Stefan problem. The problem solution enables defining the surface melt penetration of the material under the heat flow proceeding from the time of its action and the physical properties of the processed material. To determine the rational EDM operating conditions of platinum the article suggests relating its workability with machinability of materials, for which the rational EDM operating conditions are, currently, defined. It is shown that at low densities of the heat flow corresponding to the finishing EDM operating conditions, the processing conditions used for steel 45 are appropriate for platinum machining; with EDM at higher heat flow densities (e.g. 50 GW / m2 for this purpose copper processing conditions are used; at the high heat flow densities corresponding to heavy roughing EDM it is reasonable to use tungsten processing conditions. The article also represents how the minimum width of the current pulses, at which platinum starts melting and, accordingly, the EDM process becomes possible, depends on the heat flow density. It is shown that the processing of platinum is expedient at a pulse width corresponding to the values, called the effective pulse width. Exceeding these values does not lead to a substantial increase in removal of material per pulse, but considerably reduces the maximum repetition rate and therefore, the EDM capacity. The paper shows the effective pulse width versus the heat flow density. It also presents the dependences of the maximum platinum surface melt penetration and the corresponding pulse width on the heat flow density. Results obtained using solutions of the Stephen heat problem can be used to optimize EDM operating conditions of platinum machining.

Aberrant DNA damage response pathways may predict the outcome of platinum chemotherapy in ovarian cancer.

Directory of Open Access Journals (Sweden)

Dimitra T Stefanou

Full Text Available Ovarian carcinoma (OC is the most lethal gynecological malignancy. Despite the advances in the treatment of OC with combinatorial regimens, including surgery and platinum-based chemotherapy, patients generally exhibit poor prognosis due to high chemotherapy resistance. Herein, we tested the hypothesis that DNA damage response (DDR pathways are involved in resistance of OC patients to platinum chemotherapy. Selected DDR signals were evaluated in two human ovarian carcinoma cell lines, one sensitive (A2780 and one resistant (A2780/C30 to platinum treatment as well as in peripheral blood mononuclear cells (PBMCs from OC patients, sensitive (n = 7 or resistant (n = 4 to subsequent chemotherapy. PBMCs from healthy volunteers (n = 9 were studied in parallel. DNA damage was evaluated by immunofluorescence γH2AX staining and comet assay. Higher levels of intrinsic DNA damage were found in A2780 than in A2780/C30 cells. Moreover, the intrinsic DNA damage levels were significantly higher in OC patients relative to healthy volunteers, as well as in platinum-sensitive patients relative to platinum-resistant ones (all P<0.05. Following carboplatin treatment, A2780 cells showed lower DNA repair efficiency than A2780/C30 cells. Also, following carboplatin treatment of PBMCs ex vivo, the DNA repair efficiency was significantly higher in healthy volunteers than in platinum-resistant patients and lowest in platinum-sensitive ones (t1/2 for loss of γH2AX foci: 2.7±0.5h, 8.8±1.9h and 15.4±3.2h, respectively; using comet assay, t1/2 of platinum-induced damage repair: 4.8±1.4h, 12.9±1.9h and 21.4±2.6h, respectively; all P<0.03. Additionally, the carboplatin-induced apoptosis rate was higher in A2780 than in A2780/C30 cells. In PBMCs, apoptosis rates were inversely correlated with DNA repair efficiencies of these cells, being significantly higher in platinum-sensitive than in platinum-resistant patients and lowest in healthy volunteers (all P<0.05. We conclude

Biological role in the transformation of platinum-group mineral grains

Science.gov (United States)

Reith, Frank; Zammit, Carla M.; Shar, Sahar S.; Etschmann, Barbara; Bottrill, Ralph; Southam, Gordon; Ta, Christine; Kilburn, Matthew; Oberthür, Thomas; Ball, Andrew S.; Brugger, Joël

2016-04-01

Platinum-group elements are strategically important metals. Finding new deposits is becoming increasingly difficult owing to our limited understanding of the processes that affect their mobility in surface environments. Microorganisms have been shown to promote the mobility of metals around ore deposits. Here we show that microorganisms influence the mobility of platinum-group elements in mineral grains collected from Brazil, Australia and Colombia. Scanning electron microscopy showed biofilms covering the platinum-group mineral grains. The biofilms contained abundant platinum-group element nanoparticles and microcrystalline aggregates, and were dominated by Proteobacteria, many of which were closely related to known metal-resistant species. Some platinum-group mineral grains contained carbon, nitrogen, sulfur, selenium and iodine, suggesting the grains may be biogenic in origin. Molecular analyses show that Brazilian platinum-palladium grains hosted specific bacterial communities, which were different in composition from communities associated with gold grains, or communities in surrounding soils and sediments. Nano-phase metallic platinum accumulated when a metallophillic bacterium was incubated with a percolating platinum-containing medium, suggesting that biofilms can cause the precipitation of mobile platinum complexes. We conclude that biofilms are capable of forming or transforming platinum-group mineral grains, and may play an important role for platinum-group element dispersion and re-concentration in surface environments.

Metal Oxide-Supported Platinum Overlayers as Proton-Exchange Membrane Fuel Cell Cathodes

DEFF Research Database (Denmark)

Tripkovic, Vladimir; Abild-Pedersen, Frank; Studt, Felix

2012-01-01

We investigated the activity and stability of n=(1, 2, 3) platinum layers supported on a number of rutile metal oxides (MO2; M=Ti, Sn, Ta, Nb, Hf and Zr). A suitable oxide support can alleviate the problem of carbon corrosion and platinum dissolution in Pt/C catalysts. Moreover, it can increase t...

In vitro effects of platinum compounds on renal cellular respiration in mice.

Science.gov (United States)

Almarzooqi, Saeeda-S; Alfazari, Ali-S; Abdul-Kader, Hidaya-M; Saraswathiamma, Dhanya; Albawardi, Alia-S; Souid, Abdul-Kader

2015-01-01

Cisplatin, carboplatin and oxaliplatin are structurally-related compounds, which are commonly used in cancer therapy. Cisplatin (Platinol(®)) has Boxed Warning stating: "Cumulative renal toxicity associated with PLATINOL is severe", while carboplatin and oxaliplatin are less nephrotoxic. These drugs form platinum adducts with cellular DNA. Their bindings to cellular thiols (e.g., glutathione and metallothionein) are known to contribute to drug resistance while thiol depletion augments platinum toxicity. Using phosphorescence oxygen analyzer, this study investigated the effects of platinum drugs on renal cellular respiration (mitochondrial O2 consumption) in the presence and absence of the thiol blocking agent N-ethylmaleimide (used here as a model for thiol depletion). Renal cellular ATP was also determined. Kidney fragments from C57BL/6 mice were incubated at 37 °C in Krebs-Henseleit buffer (gassed with 95% O2:5% CO2) with and without 100 μM platinum drug in the presence and absence of 100 μM N-ethylmaleimide for ≤ 6 h. Platinum drugs alone had no effects on cellular respiration (P ≥ 0.143) or ATP (P ≥ 0.161). N-ethylmaleimide lowered cellular respiration (P ≤ 0.114) and ATP (P = 0.008). The combination of platinum drug and N-ethylmaleimide significantly lowered both cellular respiration (P ≤ 0.006) and ATP (P ≤ 0.003). Incubations with N-ethylmaleimide alone were associated with moderate-to-severe tubular necrosis. Incubations with cisplatin+N-ethylmaleimide vs. cisplatin alone produced similar severities of tubular necrosis. Tubular derangements were more prominent in carboplatin+N-ethylmaleimide vs. carboplatin alone and in oxaliplatin+N-ethylmaleimide vs. oxaliplatin alone. These results demonstrate the adverse events of thiol depletion on platinum-induced nephrotoxicities. The results suggest cellular bioenergetics is a useful surrogate biomarker for assessing drug-induced nephrotoxicities.

Protection against the clastogenic effect of CIS-PLATINUM by WR-2721, ATP and Vitamin C

International Nuclear Information System (INIS)

Rupova, I.; Yagova, A.

1993-01-01

The mutagenic effect of antineoplastic drug Cis-Platinum has been assessed by the frequency of micronuclei in polychromatic erythrocytes (PE) in the mouse bone marrow at time intervals of 24, 48 and 73 h. The maximal clastogenic effect of 2 mg/kg of Cis-Platinum has been found at 24 h interval after treatment (3.6%). The protection against mutagenic activity of Cis-Platinum has been studied by pretreatment of the mice with the thiophosphate compound WR-2721, adenosine triphosphate (ATP) and Vitamin C alone or in combinations at the time of maximal response. The radioprotector WR-2721 exerts a high anti-mutagenic activity when applied prior to Cis-Platinum (2.2%; p 0.05). (author)

Characterization of electrochemically modified polycrystalline platinum surfaces

Energy Technology Data Exchange (ETDEWEB)

Krebs, L.C.; Ishida, Takanobu.

1991-12-01

The characterization of electrochemically modified polycrystalline platinum surfaces has been accomplished through the use of four major electrochemical techniques. These were chronoamperometry, chronopotentiommetry, cyclic voltammetry, and linear sweep voltammetry. A systematic study on the under-potential deposition of several transition metals has been performed. The most interesting of these were: Ag, Cu, Cd, and Pb. It was determined, by subjecting the platinum electrode surface to a single potential scan between {minus}0.24 and +1.25 V{sub SCE} while stirring the solution, that the electrocatalytic activity would be regenerated. As a consequence of this study, a much simpler method for producing ultra high purity water from acidic permanganate has been developed. This method results in water that surpasses the water produced by pyrocatalytic distillation. It has also been seen that the wettability of polycrystalline platinum surfaces is greatly dependent on the quantity of oxide present. Oxide-free platinum is hydrophobic and gives a contact angle in the range of 55 to 62 degrees. We have also modified polycrystalline platinum surface with the electrically conducting polymer poly-{rho}-phenylene. This polymer is very stable in dilute sulfuric acid solutions, even under applied oxidative potentials. It is also highly resistant to electrochemical hydrogenation. The wettability of the polymer modified platinum surface is severely dependent on the choice of supporting electrolyte chosen for the electrochemical polymerization. Tetraethylammonium tetrafluoroborate produces a film that is as hydrophobic as Teflon, whereas tetraethylammonium perchlorate produces a film that is more hydrophilic than oxide-free platinum.

Characterization of electrochemically modified polycrystalline platinum surfaces

Energy Technology Data Exchange (ETDEWEB)

Krebs, Leonard C. [State Univ. of New York (SUNY), Stony Brook, NY (United States); Ishida, Takanobu [State Univ. of New York (SUNY), Stony Brook, NY (United States)

1991-12-01

The characterization of electrochemically modified polycrystalline platinum surfaces has been accomplished through the use of four major electrochemical techniques. These were chronoamperometry, chronopotentiommetry, cyclic voltammetry, and linear sweep voltammetry. A systematic study on the under-potential deposition of several transition metals has been performed. The most interesting of these were: Ag, Cu, Cd, and Pb. It was determined, by subjecting the platinum electrode surface to a single potential scan between -0.24 and +1.25 V_SCE while stirring the solution, that the electrocatalytic activity would be regenerated. As a consequence of this study, a much simpler method for producing ultra high purity water from acidic permanganate has been developed. This method results in water that surpasses the water produced by pyrocatalytic distillation. It has also been seen that the wettability of polycrystalline platinum surfaces is greatly dependent on the quantity of oxide present. Oxide-free platinum is hydrophobic and gives a contact angle in the range of 55 to 62 degrees. We have also modified polycrystalline platinum surface with the electrically conducting polymer poly-ρ-phenylene. This polymer is very stable in dilute sulfuric acid solutions, even under applied oxidative potentials. It is also highly resistant to electrochemical hydrogenation. The wettability of the polymer modified platinum surface is severely dependent on the choice of supporting electrolyte chosen for the electrochemical polymerization. Tetraethylammonium tetrafluoroborate produces a film that is as hydrophobic as Teflon, whereas tetraethylammonium perchlorate produces a film that is more hydrophilic than oxide-free platinum.

Production of platinum radioisotopes at Brookhaven Linac Isotope Producer (BLIP

Directory of Open Access Journals (Sweden)

Smith Suzanne V.

2017-01-01

Full Text Available The accelerator production of platinum isotopes was investigated at the Brookhaven Linac Isotope Producer (BLIP. In this study high purity natural platinum foils were irradiated at 53.2, 65.7, 105.2, 151.9, 162.9 and 173.3.MeV. The irradiated foils were digested in aqua regia and then converted to their hydrochloride salt with concentrated hydrochloric acid before analyzing by gamma spectrometry periodically for at least 10 days post end of bombardment. A wide range of platinum (Pt, gold (Au and iridium (Ir isotopes were identified. Effective cross sections at BLIP for Pt-188, Pt-189, Pt-191 and Pt-195m were compared to literature and theoretical cross sections determined using Empire-3.2. The majority of the effective cross sections (<70 MeV confirm those reported in the literature. While the absolute values of the theoretical cross sections were up to a factor of 3 lower, Empire 3.2 modeled thresholds and maxima correlated well with experimental values. Preliminary evaluation into a rapid separation of Pt isotopes from high levels of Ir and Au isotopes proved to be a promising approach for large scale production. In conclusion, this study demonstrated that with the use of isotopically enriched target material accelerator production of selected platinum isotopes is feasible over a wide proton energy range.

Economically attractive route for the preparation of high quality magnetic nanoparticles by the thermal decomposition of iron(III) acetylacetonate.

Science.gov (United States)

Effenberger, Fernando B; Couto, Ricardo A; Kiyohara, Pedro K; Machado, Giovanna; Masunaga, Sueli H; Jardim, Renato F; Rossi, Liane M

2017-03-17

The thermal decomposition (TD) methods are among the most successful in obtaining magnetic nanoparticles with a high degree of control of size and narrow particle size distribution. Here we investigated the TD of iron(III) acetylacetonate in the presence of oleic acid, oleylamine, and a series of alcohols in order to disclose their role and also investigate economically attractive alternatives for the synthesis of iron oxide nanoparticles without compromising their size and shape control. We have found that some affordable and reasonably less priced alcohols, such as 1,2-octanediol and cyclohexanol, may replace the commonly used and expensive 1,2-hexadecanediol, providing an economically attractive route for the synthesis of high quality magnetic nanoparticles. The relative cost for the preparation of Fe 3 O 4 NPs is reduced to only 21% and 9% of the original cost when using 1,2-octanediol and cyclohexanol, respectively.

Multi-wall carbon nanotubes supported molybdenyl acetylacetonate: Efficient and highly reusable catalysts for epoxidation of alkenes with tert-butyl hydroperoxide

Energy Technology Data Exchange (ETDEWEB)

Esnaashari, Fariba [Department of Chemistry, Catalysis Division, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of); Moghadam, Majid, E-mail: moghadamm@sci.ui.ac.ir [Department of Chemistry, Catalysis Division, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of); Mirkhani, Valiollah, E-mail: mirkhani@sci.ui.ac.ir [Department of Chemistry, Catalysis Division, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of); Tangestaninejad, Shahram; Mohammadpoor-Baltork, Iraj; Khosropour, Ahmad Reza; Zakeri, Maryam [Department of Chemistry, Catalysis Division, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of)

2012-11-15

Efficient epoxidation of olefins catalyzed by MoO{sub 2}(acac){sub 2} supported on amines functionalized MWCNTs is reported. The MWCNTs bearing carboxylic acid groups were modified with 2-aminophenol and 2-aminothiophenol. These amine-MWCNTs act as bidentate ligand for attachment of Mo catalyst. These catalysts were characterized by elemental analysis, scanning electron microscopy, FT-IR and diffuse reflectance UV-Vis spectroscopic methods. The prepared catalysts were used for efficient epoxidation of different alkenes such as cyclic and linear ones with tert-butyl hydroperoxide in refluxing 1,2-dichloroethane. These heterogeneous catalysts can be reused several times without significant loss of their catalytic activity. Highlights: Black-Right-Pointing-Pointer Supporting of molybdenyl acetylacetonate on amine-modified MWCNTs. Black-Right-Pointing-Pointer Heterogeneous catalysts were prepared. Black-Right-Pointing-Pointer These catalysts were highly efficient in the epoxidation of alkenes with TBHP. Black-Right-Pointing-Pointer Makes the catalysts reusable.

Solar Hydrogen Production Coupled with the Degradation of a Dye Pollutant Using TiO2 Modified with Platinum and Nafion

Directory of Open Access Journals (Sweden)

Jungwon Kim

2014-01-01

Full Text Available The simultaneous production of molecular hydrogen (H2 and degradation of rhodamine B (RhB was successfully achieved using TiO2 modified with platinum and nafion (Pt/TiO2/Nf under visible light (λ>420 nm. Pt/TiO2/Nf exhibited high activity for H2 production in the presence of RhB and EDTA as a photosensitizer (also an organic dye pollutant and an electron donor, respectively. However, the activity of TiO2 modified with either platinum or nafion for H2 production was negligible under the same experimental conditions. The negatively charged nafion layer enhances the adsorption of cationic RhB and pulls protons, a source of hydrogen, to the surface of TiO2 through electrostatic attraction. On the other hand, platinum deposits on TiO2 can act as an electron sink and a temporary electron reservoir for the reduction of protons. With the production of H2, RhB was gradually degraded through N-deethylation, which was confirmed by the spectral blue shift of the maximum absorption wavelength (λmax from 556 to 499 nm (corresponding to the λmax of rhodamine 110. With Pt/TiO2/Nf employed at [RhB]=20 μM (0.6 μmol, approximately 70 μmol of H2 was produced and RhB and its intermediates were completely removed over a 12 h period. A detailed reaction mechanism was discussed.

Corrosion Studies of Platinum Nano-Particles for Fuel Cells

DEFF Research Database (Denmark)

Shim, Signe Sarah

The main focus of the present thesis is on corrosion and prevention of corrosion of platinum particles supported on carbon. This is important for instance in connection with start up and shutdown of fuel cells. The degradation mechanism of platinum particles supported on carbon has been character......The main focus of the present thesis is on corrosion and prevention of corrosion of platinum particles supported on carbon. This is important for instance in connection with start up and shutdown of fuel cells. The degradation mechanism of platinum particles supported on carbon has been...... characterized during oxygen reduction reaction (ORR) condition using identical location (IL) transmission electron microscopy (TEM). A TEM grid was used as the working electrode in an electrochemical setup allowing a direct correlation between the electrochemical response and the TEM analysis. The main results...... thirds and one monolayer of gold on platinum supported on carbon were synthesized by an inverse micelle method. The results obtained appear independent of the gold coverage. It has been shown that the electrochemical active surface areas of the platinum and platinum gold particles synthesized...

Outpatient desensitization in selected patients with platinum hypersensitivity reactions.

Science.gov (United States)

O'Malley, David M; Vetter, Monica Hagan; Cohn, David E; Khan, Ambar; Hays, John L

2017-06-01

Platinum-based chemotherapies are a standard treatment for both initial and recurrent gynecologic cancers. Given this widespread use, it is important to be aware of the features of platinum hypersensitivity reactions and the subsequent treatment of these reactions. There is also increasing interest in the development of desensitization protocols to allow patients with a history of platinum hypersensitivity to receive further platinum based therapy. In this review, we describe the management of platinum hypersensitivity reactions and the desensitization protocols utilized at our institution. We also describe the clinical categorizations utilized to triage patients to appropriate desensitization protocols. Copyright © 2017 Elsevier Inc. All rights reserved.

Electrical conductivity of platinum-implanted polymethylmethacrylate nanocomposite

Science.gov (United States)

Salvadori, M. C.; Teixeira, F. S.; Cattani, M.; Brown, I. G.

2011-12-01

Platinum/polymethylmethacrylate (Pt/PMMA) nanocomposite material was formed by low energy ion implantation of Pt into PMMA, and the transition from insulating to conducting phase was explored. In situ resistivity measurements were performed as the implantation proceeded, and transmission electron microscopy was used for direct visualization of Pt nanoparticles. Numerical simulation was carried out using the TRIDYN computer code to calculate the expected depth profiles of the implanted platinum. The maximum dose for which the Pt/PMMA system remains an insulator/conductor composite was found to be ϕ0 = 1.6 × 1016 cm-2, the percolation dose was 0.5 × 1016 cm-2, and the critical exponent was t = 1.46, indicating that the conductivity is due only to percolation. The results are compared with previously reported results for a Au/PMMA composite.

In vitro free radical scavenging activity of platinum nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Watanabe, Aki; Kajita, Masashi; Kim, Juewon; Kanayama, Atsuhiro; Miyamoto, Yusei [Department of Integrated Biosciences, Graduate School of Frontier Sciences, University of Tokyo, Bioscience Building 402, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8562 (Japan); Takahashi, Kyoko; Mashino, Tadahiko, E-mail: yusei74@k.u-tokyo.ac.j [Department of Pharmaceutical Sciences, Faculty of Pharmacy, Keio University, 1-5-30 Shibakoen, Minato, Tokyo 105-8512 (Japan)

2009-11-11

A polyacrylic acid (PAA)-protected platinum nanoparticle species (PAA-Pt) was prepared by alcohol reduction of hexachloroplatinate. The PAA-Pt nanoparticles were well dispersed and homogeneous in size with an average diameter of 2.0 {+-} 0.4 nm (n = 200). We used electron spin resonance to quantify the residual peroxyl radical AOO. generated from 2,2-azobis (2-aminopropane) dihydrochloride (AAPH) by thermal decomposition in the presence of O{sub 2} and a spectrophotometric method to quantify the residual 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical. PAA-Pt scavenged these two radicals in a dose-dependent manner. Platinum was the functional component. PAA-Pt reduced the rate of oxygen consumption required for linoleic acid peroxidation initiated by AOO. generated from AAPH, indicating inhibition of the propagation of linolate peroxidation. A thiobarbituric acid test also revealed dose-dependent inhibition of the linolate peroxidation by PAA-Pt. Fifty micromolar platinum, as PAA-Pt, completely quenched 250 {mu}M DPPH radical for 5 min. Even when twice diluted in half, the PAA-Pt still quenched 100% of the 250 {mu}M DPPH radical. The scavenging activity of PAA-Pt is durable. These observations suggest that PAA-Pt is an efficient scavenger of free radicals.

Preparation of Carbon-Platinum-Ceria and Carbon-Platinum-Cerium catalysts and its application in Polymer Electrolyte Fuel Cell: Hydrogen, Methanol, and Ethanol

Science.gov (United States)

Guzman Blas, Rolando Pedro

This thesis is focused on fuel cells using hydrogen, methanol and ethanol as fuel. Also, in the method of preparation of catalytic material for the anode: Supercritical Fluid Deposition (SFD) and impregnation method using ethylenediaminetetraacetic acid (EDTA) as a chelating agent. The first part of the thesis describes the general knowledge about Hydrogen Polymer Exchange Membrane Fuel Cell (HPEMFC),Direct Methanol Fuel Cell (DMFC) and Direct Ethanol Fuel Cell (DEFC), as well as the properties of Cerium and CeO2 (Ceria). The second part of the thesis describes the preparation of catalytic material by Supercritical Fluid Deposition (SFD). SFD was utilized to deposit Pt and ceria simultaneously onto gas diffusion layers. The Pt-ceria catalyst deposited by SFD exhibited higher methanol oxidation activity compared to the platinum catalyst alone. The linear sweep traces of the cathode made for the methanol cross over study indicate that Pt-Ceria/C as the anode catalyst, due to its better activity for methanol, improves the fuel utilization, minimizing the methanol permeation from anode to cathode compartment. The third and fourth parts of the thesis describe the preparation of material catalytic material Carbon-Platinum-Cerium by a simple and cheap impregnation method using EDTA as a chelating agent to form a complex with cerium (III). This preparation method allows the mass production of the material catalysts without additional significant cost. Fuel cell polarization and power curves experiments showed that the Carbon-Platinum-Cerium anode materials exhibited better catalytic activity than the only Vulcan-Pt catalysts for DMFC, DEFC and HPEMFC. In the case of Vulcan-20%Pt-5%w Cerium, this material exhibits better catalytic activity than the Vulcan-20%Pt in DMFC. In the case of Vulcan-40% Pt-doped Cerium, this material exhibits better catalytic activity than the Vulcan-40% Pt in DMFC, DEFC and HPEMFC. Finally, I propose a theory that explains the reason why the

Room temperature H{sub 2}S gas sensing characteristics of platinum (Pt) coated porous alumina (PoAl) thick films

Energy Technology Data Exchange (ETDEWEB)

More, P.S., E-mail: p_smore@yahoo.co.in [Department of Physics, Institute of Science, Mumbai 400 032 (India); Raut, R.W. [Department of Botany, Institute of Science, Mumbai 400 032 (India); Ghuge, C.S. [Department of Physics, Institute of Science, Mumbai 400 032 (India)

2014-02-14

The study reports H{sub 2}S gas sensing characteristics of platinum (Pt) coated porous alumina (PoAl) films. The porous alumina (PoAl) thick layers were formed in the dark on aluminum substrates using an electrochemical anodization method. Thin semitransparent platinum (Pt) films were deposited on PoAl samples using chemical bath deposition (CBD) method. The films were characterized using energy dispersive X-ray analysis (EDAX) and scanning electron microscopy (SEM). The thicknesses of coated and bare films were measured using ellipsometry. The sensing properties such as sensitivity factor (S.F.), response time, recovery time and repeatability were measured using a static gas sensing system for H{sub 2}S gas. The EDAX studies confirmed the purity of Pt–PoAl film and indicated the formation of pure platinum (Pt) phase. The ellipsometry studies revealed the thickness of PoAl layer of about 15–17 μm on aluminum substrates. The SEM studies demonstrated uniform distribution of spherical pores with a size between 0.250 and 0.500 μm for PoAl film and nearly spherical platinum particles with average particle size ∼100 nm for Pt–PoAl film. The gas-sensing properties of these samples were studied in a home-built static gas characterization system. The H{sub 2}S gas sensing properties of Pt–PoAl at 1000 ppm of H{sub 2}S gave maximum sensitivity factor (S.F.) = 1200. The response time and recovery time were found to be 2–3 min and ∼1 min respectively. Further, the measurement of H{sub 2}S gas sensing properties clearly indicated the repeatability of gas sensing response of Pt–PoAl film. The present study indicated the significant potential of Pt coated PoAl films for H{sub 2}S gas sensing applications in diverse areas. - Highlights: • Electrochemical anodization, cheap and effective method for fabrication of PoAl. • Chemical bath deposition, a simple and effective method for deposition of Pt on PoAl. • A nano-composite film sensor with high sensitivity

Electrochemical behavior of titanium implanted with platinum

International Nuclear Information System (INIS)

Thompson, N.G.; Lichter, B.D.; Appleton, B.R.; Kelly, E.J.; White, C.W.

1979-01-01

The following conclusions apply to Ti(Pt) near-surface alloys studied. (1) Open-circuit corrosion measurements show that accumulation of platinum may occur at a surface concentration of 0.32 atomic percent Pt while no accumulation occurs at 0.16 atomic percent Pt. However, these results do not allow a distinction as to cause of accumulation to be made between concentration effects and effects due to the presence of an oxide film. (2) Potentiostatic corrosion at -0.450 V (active corrosion) establish that little or no accumulation of platinum occurs at an oxide-free surface for concentrations less than 0.086 atomic percent Pt; whereas, a large amount of accumulation occurs for a distribution with a peak concentration of 0.83 atomic percent Pt. (3) An initial distribution having a peak concentration of 0.32 atomic percent platinum is sufficient to induce natural passivity in titanium and bring a freely corroding sample to a potential of 0.269 V. This is nearly the applicable reversible potential (-0.260 V) for the hydrogen reaction in 1N H 2 SO 4 . (4) Of three samples which showed accumulation, platinum was eventually lost for two of these samples (0.32 atomic percent, open-circuit corrosion; 0.83 atomic percent, potentiostatic corrosion). The remaining sample (9.1 atomic percent, open-circuit corrosion) maintained the maximum possible potential of -0.260 V for the length of the experiment (approx. 30 days). (5) For samples which had been polarized at -0.300 to -0.340 V and which had eventually reverted to the behavior of pure Ti, post corrosion RBS measurements reveal that a substantial fraction of the Pt fluence is retained on the surface in an electrochemically inactive state

Rhenium–platinum antitumor systems

Directory of Open Access Journals (Sweden)

A. V. Shtemenko

2017-04-01

Full Text Available This review provides an overlook of design (in short, antitumor and other biological activity of quadruple-bonded cluster dirhenium(III compounds and their synergism with cisplatin. In particular, we describe the work of the rhenium-platinum antitumor system (introduction of rhenium and platinum compounds. Among known metal-based anticancer drugs and drug candidates dirhenium(III compounds differ profoundly due to their strong antiradical and antioxidant properties determined by quadruple bond unsaturation. Such advantages of metal complexes as more expressed redox chemical propertie should be exploited for creating more efficient anticancer drugs. Combination of drugs leads to synergistic effects and/or to lowe­ring toxicity of platinides and is very promising in cancer chemotherapy. The review covers the follo­wing items: design of quadruple bonded dirhenium(III clusters, their spectral and antiradical properties (in short; interaction of the dirhenium(III compounds with lipids and formation of liposomes; interaction of the dirhenium(III compounds with erythrocytes and their antihemolytic activity in the models of hemolytic anemia; anticancer activity of dirhenium clusters and work of the rhenium-platinum antitumor system; antianemic and antioxidant properties of the dirhenium(III compounds in the model of tumor growth; interaction of the dirhenium(III compounds with nucleobases and DNA. Some modern trends in the field of bioinorganic and medicinal chemi­stry are also considered regarding their connection to the rhenium-platinum system efficiency: use of combinational therapy and nanomaterials; involvement of some biologically active ligands and redox-activation strategy, etc.

A NEW EMPIRICAL INVESTIGATION OF THE PLATINUM SPOT RETURNS

Directory of Open Access Journals (Sweden)

Simone Kruse

2017-08-01

Full Text Available The global platinum market has been in downturn and unstable for five consecutive years, and thus market participants are demanding effective quantitative risk management tools. Since platinum is so widely used and serves as an important investment vehicle, the importance of risk management of platinum spot returns cannot be understated. In this paper, we take advantage of a very popular econometric model, the generalized autoregressive conditional heteroscedasticity (GARCH model, for platinum returns. We received two important findings by using the conventional GARCH models in explain daily platinum spot returns. First, it is crucial to introduce heavy-tailed distribution to explain conditional heavy tails; and second, the NRIG distribution performs better than the most widely-used heavy-tailed distribution, the Student’s t distribution.

Mechanism of Platinum Derivatives Induced Kidney Injury

Directory of Open Access Journals (Sweden)

Feifei YAN

2015-09-01

Full Text Available Platinum derivatives are the most widely used chemotherapeutic agents to treat solid tumors including ovarian, head and neck, and testicular germ cell tumors, lung cancer, and colorectal cancer. Two major problems exist, however, in the clinic use of platinum derivatives. One is the development of tumor resistance to the drug during therapy, leading to treatment failure. The other is the drug’s toxicity such as the cisplatin’s nephrotoxicity, which limits the dose that can be administered. This paper describes the mechanism of platinum derivatives induced kidney injury.

Collective Behavior of Water on Platinum

Science.gov (United States)

Limmer, David; Willard, Adam; Chandler, David

2012-02-01

We present the results of molecular dynamics simulations of a interface between water and a platinum electrode. Using importance sampling techniques we probe a variety of collective phenomenon that emerge at the interface. We consider platinum electrodes with two different geometries and discuss how different behaviors result from a competition between geometrical frustration and favorable local interactions.

Simultaneous determination of palladium, platinum and rhodium by on-line column enrichment and HPLC with 2,4-dihydroxybenzylidenethiorhodanine as pre-column derivatization reagent

Directory of Open Access Journals (Sweden)

Dong Xuechang

2006-01-01

Full Text Available A new method for the simultaneous determination of palladium, platinum and rhodium ions as metal-DHBTR chelates was developed. The palladium, platinum and rhodium ions were pre-column derivatized with 2,4-dihydroxybenzylidenethiorhodanine (DHBTR to form colored chelates. The Pd-DHBTR, Pt-DHBTR and Rh-DHBTR chelates can be absorbed onto the front of the enrichment column when they were injected into the injector and sent to the enrichment column with a 0.05 mol L-1 sodium acetate-acetic acid buffer solution (pH 3.5 as mobile phase. After the enrichment had finished, by switching the six ports switching valve, the retained chelates were back-flushed by mobile phase and traveling towards the analytical column. These chelates separation on the analytical column was satisfactory with 62% (v/v acetonitrile (containing 0.05 mol L-1 of pH 3.5 sodium acetate-acetic acid buffer salt and 0.1% (m/v of tritonX-100 as mobile phase. The Limits of detection of palladium, platinum and rhodium are 3.6 ng L-1, 3.2 ng L-1 and 4.5 ng L-1, respectively. This method was applied to the determination of palladium, platinum and rhodium in water, urine and soil samples with good results.

Structural consideration with respect to the thermal stability of a new platinum supported lanthanum-alumina catalyst

International Nuclear Information System (INIS)

Oudet, F.; Bordes, E.; Courtine, P.; Maxant, G.; Lambert, C.; Guerlet, J.P.

1987-01-01

The influence of lanthanum aluminate, LaAlO 3 , on the thermal stability of both alumina and platinum supported alumina catalysts is investigated. In the case of alumina, the stabilization is interpreted in terms of structural coherence between δ-Al 2 O 3 and a three-fold superstructure of LaAlO 3 . The addition of LaAlO 3 , is shown to increase both the dispersion and the resistance to sintering of the platinum supported alumina catalyst. Moreover, lanthanum hexa-aluminate (La-β-Al 2 O 3 ) is present in the platinum catalyst fired at 1150 0 C. These observations are assumed to result for the epitaxial relations between platinum and the lanthanum-alumina support. 23 refs.; 8 figs.; 2 tabs

Radiation induced synthesis of In{sub 2}O{sub 3} nanoparticles - Part II: Synthesis of In{sub 2}O{sub 3} nanoparticles by thermal decomposition of un-irradiated and γ-irradiated indium acetylacetonate

Energy Technology Data Exchange (ETDEWEB)

Al-Resheedi, Ajayb Saud; Alhokbany, Norah Saad [Department of Chemistry, College of Science, King Saud University, KSU, (Saudi Arabia); Mahfouz, Refaat Mohammed, E-mail: rmhfouz@science.au.edu.eg [Chemistry Department, Faculty of Science, Assiut University, AUN, (Egypt)

2015-09-15

Pure cubic phase, In{sub 2}O{sub 3} nanoparticles with porous structure were synthesized by solid state thermal oxidation of un-irradiated and γ-irradiated indium acetyl acetonate in presence and absence of sodium dodecyl sulphate as surfactant. The as- synthesized In{sub 2}O{sub 3} nanoparticles were characterized by X-ray diffraction (XRD), fourier transformation infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transition electron microscopy (TEM) and thermogravimetry (TG). The shapes and morphologies of as- synthesized In{sub 2}O{sub 3} nanoparticles were highly affected by γ-irradiation of indium acetyl acetonate precursor and by addition of sodium dodecyl sulphate as surfactant. Calcination of un-irradiated indium acetyl acetonate precursor to 4 hours of 600 °C leads to the formation of spherical- shaped accumulative and merged In{sub 2}O{sub 3} nanoparticles with porous structure, whereas irregular porous architectures composed of pure In{sub 2}O{sub 3} nanoparticles were obtained by using γ-irradiated indium acetylacetonate precursor. The as- prepared In{sub 2}O{sub 3} nano products exhibit photoluminescence emission (PL) property and display thermal stability in a wide range of temperature (25-800 °C) which suggest possible applications in nanoscale optoelectronic devices. (author)

A novel reusable platinum nanocatalyst

International Nuclear Information System (INIS)

Zhou Weiqiang; Wang Jing; Wang Chuanyi; Du Yukou; Xu Jingkun; Yang Ping

2010-01-01

Recyclability of noble metal catalysts is a challenging issue when dealing with their industrial applications. Smart pH-sensitive Pt nanoparticles were successfully prepared for the first time by using octa(N,N-diacetic acid phenylamine)silsesquioxane (OAPAS) as a macromolecular protective agent. As-prepared Pt nanoparticles can self-aggregate or redisperse by only changing the pH of the system solution. In the weak acidic or alkaline solution (pH > 4.0), the Pt nanoparticles dispersed homogenously; while in the acidic solution (pH = 2.5), they self-aggregated. The dynamic self-aggregation and redispersion processes of the Pt nanoparticles driven by pH changes were revealed by transmission electron microscopy measurements. Electrocatalytic experiments proved that the platinum nanoparticles as a recyclable catalyst showed excellent activity for the hydrogenation of aldehyde after runs of five times. Such platinum nanoparticles are thereby anticipated to have great potential functioning as 'smart' catalysts for industrial applications.

Comparison of different sample preparation methods for platinum determination in cultured cells by graphite furnace atomic absorption spectrometry

Directory of Open Access Journals (Sweden)

Man Xiao

2017-01-01

Full Text Available Background Platinum-based agents are widely used in chemotherapy against solid tumors and insufficient intracellular drug accumulation is one of the leading causes of platinum resistance which is associated with poor survival of tumor patients. Thus, the detection of intracellular platinum is pivotal for studies aiming to overcome platinum resistance. In the present study, we aimed to establish a reliable graphite furnace atomic absorption spectrometry (GFAAS-based assay to quantify the intracellular platinum content for cultured cells. Methods Several most commonly applied cell preparation methods, including 0.2% HNO3, 0.2% Triton X-100, concentrated nitric acid, RIPA combined with concentrated nitric acid and hydroxide, followed by GFAAS for platinum detection were compared in ovarian, cervical and liver cancer cell lines to obtain the optimal one, and parameters regarding linearity, accuracy, precision and sensitivity were evaluated. Influence of other metals on platinum detection and the storage conditions of samples were also determined. Results The treatment of cells with 0.2% HNO3 was superior to other approaches with fewer platinum loss and better repeatability. The recovery rate and precision of this method were 97.3%–103.0% and 1.4%–3.8%, respectively. The average recoveries in the presence of other metals were 95.1%–103.1%. The detection limit was 13.23 ug/L. The recovery rate of platinum remained acceptable even in cell samples stored in −20 °C or −80 °C for two months. Discussion After comparison, we found that 0.2% HNO3 was optimal for intracellular platinum quantification based on GFAAS, which presented values compatible with that of inductively-coupled plasma mass-spectrometry (ICP-MS, and this is partially attributed to the simplicity of this method. Moreover, the assay was proved to be accurate, sensitive, cost-effective and suitable for the research of platinum-based antitumor therapy.

Characterization and Catalytic Activity for the Oxidation of Ethane and Propane on Platinum and Copper Supported on CeO2/Al2O3

Directory of Open Access Journals (Sweden)

Cataluña R.

1998-01-01

Full Text Available Ethane and propane oxidation on platinum and copper supported on Al2O3 and CeO2/Al2O3 catalysts were studied comparatively by examining reaction rates as a function of temperature. Results show that the addition of cerium oxide shifts the catalytic activity to higher temperatures. This negative influence is less pronounced in the case of supported copper samples, which on the basis of EPR and FTIR of adsorbed CO results is attributed to the low relative amount of this metal is in contact with ceria. The decrease in activity the presence of ceria might be due to changes in metal particle size or to the stabilization of the oxidized states of the metals, induced by their interactions with cerium oxide. The higher activity of platinum, in comparison with copper, is attributed to its higher reducibility along with an easier hydrocarbon activation on that metal.

Controllable deposition of platinum nanoparticles on single-wall carbon nanohorns as catalyst for direct methanol fuel cells.

Science.gov (United States)

Niu, Ben; Xu, Wei; Guo, Zhengduo; Zhou, Nengzhi; Liu, Yang; Shi, Zujin; Lian, Yongfu

2012-09-01

Uniform and well dispersed platinum nanoparticles were successfully deposited on single-walled carbon nanohorns with the assistance of 4,4-dipydine and ion liquids, respectively. In particular, the size of platinum nanoparticles could be controlled in a very narrow range (2.2 to 2.5 nm) when ion liquids were applied. The crystalline nature of these platinum nanoparticles was confirmed by high resolution transmission electron microscopy observation and X-ray power diffraction analysis, and two species of platinum Pt(0) and Pt(II) were detected by X-ray photoelectron spectroscopy. Electrochemical studies revealed that thus obtained nanocomposites had much better electrocatalytic activity for the methanol oxidation than those prepared with carbon nanotubes as supporter.

Recovery of Platinum from Dilute Chloride Media Using Biosorbents

Science.gov (United States)

Zeytuncu, B.; Morcali, M. H.; Yucel, O.

Pistachio nut shells and Rice husk, a biomass residue, were investigated as adsorbents for the platinum uptake from synthetically prepared dilute chloroplatinic acid solutions. The effects of the different uptake parameters on platinum uptake (%) were studied in detail on a batch sorption. Before the pistachio nut shell material was activated, platinum uptake (%) was poor compared with rice husk. However, after the pistachio nut shell material was activated at 1000°C under an argon atmosphere, the platinum uptake (%) increased two-fold. The pistachio nut shell (inactivated and activated) and rice husk were characterized by Attenuated Total Reflection-Fourier transform infrared spectroscopy (ATR-FTIR).

Radiation and platinum drug interaction

International Nuclear Information System (INIS)

Nias, A.H.W.

1985-01-01

The ideal platinum drug-radiation interaction would achieve radiosensitization of hypoxic tumour cells with the use of a dose of drug which is completely non-toxic to normal tissues. Electron-affinic agents are employed with this aim, but the commoner platinum drugs are only weakly electron-affinic. They do have a quasi-alkylating action however, and this DNA targeting may account for the radiosensitizing effect which occurs with both pre- and post-radiation treatments. Because toxic drug dosage is usually required for this, the evidence of the biological responses to the drug and to the radiation, as well as to the combination, requires critical analysis before any claim of true enhancement, rather than simple additivity, can be accepted. The amount of enhancement will vary with both the platinum drug dose and the time interval between drug administration and radiation. Clinical schedules may produce an increase in tumour response and/or morbidity, depending upon such dose and time relationships. (author)

Structures of 38-atom gold-platinum nanoalloy clusters

Energy Technology Data Exchange (ETDEWEB)

Ong, Yee Pin; Yoon, Tiem Leong [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lim, Thong Leng [Faculty of Engineering and Technology, Multimedia University, Melaka Campus, 75450 Melaka (Malaysia)

2015-04-24

Bimetallic nanoclusters, such as gold-platinum nanoclusters, are nanomaterials promising wide range of applications. We perform a numerical study of 38-atom gold-platinum nanoalloy clusters, Au{sub n}Pt{sub 38−n} (0 ≤ n ≤ 38), to elucidate the geometrical structures of these clusters. The lowest-energy structures of these bimetallic nanoclusters at the semi-empirical level are obtained via a global-minimum search algorithm known as parallel tempering multi-canonical basin hopping plus genetic algorithm (PTMBHGA), in which empirical Gupta many-body potential is used to describe the inter-atomic interactions among the constituent atoms. The structures of gold-platinum nanoalloy clusters are predicted to be core-shell segregated nanoclusters. Gold atoms are observed to preferentially occupy the surface of the clusters, while platinum atoms tend to occupy the core due to the slightly smaller atomic radius of platinum as compared to gold’s. The evolution of the geometrical structure of 38-atom Au-Pt clusters displays striking similarity with that of 38-atom Au-Cu nanoalloy clusters as reported in the literature.

Radiochemical neutron activation analysis of high pure palladium and platinum by ion exchange chromatography

International Nuclear Information System (INIS)

Sadikov, I.I.; Zinov'ev, V.G.; Sadikova, Z.O.; Salimov, M.I.

2006-01-01

volume was obtained by elution curve of the determined elements and distribution profile of the matrix elements. Chemical yields of determined elements were measured by 'entered - found' method. Chemical yields of Sn is 31.2%; Zn is 54.5%; Se is 74.%1, and for other elements it is more than 85 %. Based on the carried out researches the radiochemical neutron activation analysis techniques of a high pure palladium and platinum are developed. These techniques allow determination of more than 30 elements with detection limits 10 -5 -10 -9 % with S r 0.15-0.2. (author)

PLD prepared nanostructured Pt-CeO2 thin films containing ionic platinum

Czech Academy of Sciences Publication Activity Database

Vorokhta, M.; Khalakhan, I.; Matolínová, I.; Nováková, J.; Haviar, M.; Lančok, Ján; Novotný, Michal; Yoshikawa, H.; Matolín, V.

2017-01-01

Roč. 396, Feb (2017), s. 278-283 ISSN 0169-4332 Institutional support: RVO:68378271 Keywords : PLD * cerium oxide * ionic platinum * HAXPES Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 3.387, year: 2016

Rapid and Efficient Collection of Platinum from Karstedt's Catalyst Solution via Ligands-Exchange-Induced Assembly.

Science.gov (United States)

Yang, Gonghua; Wei, Yanlong; Huang, Zhenzhu; Hu, Jiwen; Liu, Guojun; Ou, Ming; Lin, Shudong; Tu, Yuanyuan

2018-02-21

Reported herein is a novel strategy for the rapid and efficient collection of platinum from Karstedt's catalyst solution. By taking advantage of a ligand-exchange reaction between alkynols and the 1,3-divinyltetramethyldisiloxane ligand (M Vi M Vi ) that coordinated with platinum (Pt(0)), the Karstedt's catalyst particles with a size of approximately 2.5 ± 0.7 nm could be reconstructed and assembled into larger particles with a size of 150 ± 35 nm due to the hydrogen bonding between the hydroxyl groups of the alkynol. In addition, because the silicone-soluble M Vi M Vi ligand of the Karstedt's catalyst was replaced by water-soluble alkynol ligands, the resultant large particles were readily dispersed in water, resulting in rapid, efficient, and complete collection of platinum from the Karstedt's catalyst solutions with platinum concentrations in the range from ∼20 000 to 0.05 ppm. Our current strategy not only was used for the rapid and efficient collection of platinum from the Karstedt's catalyst solutions, but it also enabled the precise evaluation of the platinum content in the Karstedt's catalysts, even if this platinum content was extremely low (i.e., 0.05 ppm). Moreover, these platinum specimens that were efficiently collected from the Karstedt's catalyst solutions could be directly used for the evaluation of platinum without the need for pretreatment processes, such as calcination and digestion with hydrofluoric acid, that were traditionally used prior to testing via inductively coupled plasma mass spectrometry in conventional methods.

Platinum-group metals from nuclear reactions as a possible resource

International Nuclear Information System (INIS)

Jensen, G.A.

1985-03-01

Spent nuclear fuels contain significant quantities of three of the platinum-group metals (ruthenium, rhodium, and palladium), and a related element technetium, which is nearly absent in nature. Applications for ruthenium, rhodium, and palladium are well established. Since the supply of these and other platinum metals is largely from foreign sources, they are considered strategic materials. Existing and future spent nuclear fuels contain quantities of these platinum metals that exceed the United States reserve base. Technetium has properties similar to platinum metals and has unique, useful properties of its own. The technical feasibility of recovering and using fission product platinum metals (and technetium) extensively in industry depends on: thoroughly decontaminating platinum-group metals from all other radioactive materials in the waste stream; separating platinum-group metals from one another in very high purity; using applications where appropriate control of the residual radioactivity is possible; and whether or not the United States will recover or process spent fuel prior to repository storage. If the radioactivity must be removed, isotope separation or long term storage to allow decay of the contained radioisotopes may be possible. 7 figs., 7 tabs

Novel 3-(aminomethyl)naphthoquinone mannich base-platinum(IV) complexes: synthesis, characterization, electrochemical and cytotoxic studies

International Nuclear Information System (INIS)

Silva, Gustavo B. da; Neves, Amanda P.; Vargas, Maria D.; Alves, Wagner A.; Marinho-Filho, Jose D.B.; Pessoa, Claudia; Moraes, Manoel O.; Costa-Lotufo, Leticia V.

2013-01-01

Three novel platinum(IV) complexes cis,cis,trans-[Pt(HL1-3)Cl 2 (OH) 2 ] 1b-3b(HL = 2-hydroxy-3-[(R 1 -amino)(pyridin-2-yl)methyl]-1,4-naphthoquinone, R 1 = n-butyl, HL1; n-heptyl, HL2 and n-decyl, HL3) have been obtained from the oxidation of the respective precursors cis-[Pt(HL1-3)Cl 2 ] 1a-3a. Cyclic voltammetry studies of 1b-3b in MeCN showed the quasi reversible naphthoquinonate (NQO - , i.e., L - ) redox process and irreversible process attributed to the reduction of the Pt 4+ /Pt 2+ pair, at potentials about 400 mV less negative than for the cisplatin precursor cis,cis,trans-[Pt(NH 3 ) 2 Cl 2 (OH) 2 ]. Hydrogen bond interaction between the naphthoquinone 2-hydroxyl group and an axially coordinated hydroxide ligand in 1b-3b has been proposed to favor the Pt 4+ /Pt 2+ reduction. The cytotoxicity studies against four human cancer cell lines have shown that in general the platinum(IV) and platinum(II)derivatives exhibit the same cytotoxic profile and are all more active than cisplatin. The lowest in vitro IC 50 values have been observed for 2b-3b, which bear ligands with the largest R 1 groups (HL2-HL3) being the most lipophilic. Furthermore similar IC 50 values for platinum(II) and platinum(IV) complexes of the same ligands have been associated with rapid in vitro reduction of the latter complexes to afford 1a-3a. (author)

Effects of para-substituents of styrene derivatives on their chemical reactivity on platinum nanoparticle surfaces

Science.gov (United States)

Hu, Peiguang; Chen, Limei; Deming, Christopher P.; Lu, Jia-En; Bonny, Lewis W.; Chen, Shaowei

2016-06-01

Stable platinum nanoparticles were successfully prepared by the self-assembly of para-substituted styrene derivatives onto the platinum surfaces as a result of platinum-catalyzed dehydrogenation and transformation of the vinyl groups to the acetylene ones, forming platinum-vinylidene/-acetylide interfacial bonds. Transmission electron microscopic measurements showed that the nanoparticles were well dispersed without apparent aggregation, suggesting sufficient protection of the nanoparticles by the organic capping ligands, and the average core diameter was estimated to be 2.0 +/- 0.3 nm, 1.3 +/- 0.2 nm, and 1.1 +/- 0.2 nm for the nanoparticles capped with 4-tert-butylstyrene, 4-methoxystyrene, and 4-(trifluoromethyl)styrene, respectively, as a result of the decreasing rate of dehydrogenation with the increasing Taft (polar) constant of the para-substituents. Importantly, the resulting nanoparticles exhibited unique photoluminescence, where an increase of the Hammett constant of the para-substituents corresponded to a blue-shift of the photoluminescence emission, suggesting an enlargement of the HOMO-LUMO band gap of the nanoparticle-bound acetylene moieties. Furthermore, the resulting nanoparticles exhibited apparent electrocatalytic activity towards oxygen reduction in acidic media, with the best performance among the series of samples observed with the 4-tert-butylstyrene-capped nanoparticles due to an optimal combination of the nanoparticle core size and ligand effects on the bonding interactions between platinum and oxygen species.Stable platinum nanoparticles were successfully prepared by the self-assembly of para-substituted styrene derivatives onto the platinum surfaces as a result of platinum-catalyzed dehydrogenation and transformation of the vinyl groups to the acetylene ones, forming platinum-vinylidene/-acetylide interfacial bonds. Transmission electron microscopic measurements showed that the nanoparticles were well dispersed without apparent

A Single Platinum Microelectrode for Identifying Soft Drink Samples

Directory of Open Access Journals (Sweden)

Lígia Bueno

2012-01-01

Full Text Available Cyclic voltammograms recorded with a single platinum microelectrode were used along with a non-supervised pattern recognition, namely, Principal Component Analysis, to conduct a qualitative analysis of sixteen different brands of carbonated soft drinks (Kuat, Soda Antarctica, H2OH!, Sprite 2.0, Guarana Antarctica, Guarana Antarctica Zero, Coca-Cola, Coca-Cola Zero, Coca-Cola Plus, Pepsi, Pepsi Light, Pepsi Twist, Pepsi Twist Light, Pepsi Twist 3, Schin Cola, and Classic Dillar’s. In this analysis, soft drink samples were not subjected to pre-treatment. Good differentiation among all the analysed soft drinks was achieved using the voltammetric data. An analysis of the loading plots shows that the potentials of −0.65 V, −0.4 V, 0.4 V, and 0.750 V facilitated the discrimination process. The electrochemical processes related to this potential are the reduction of hydrogen ions and inhibition of the platinum oxidation by the caffeine adsorption on the electrode surface. Additionally, the single platinum microelectrode was useful for the quality control of the soft drink samples, as it helped to identify the time at which the beverage was opened.

Platinum uptake from chloride solutions using biosorbents

Directory of Open Access Journals (Sweden)

Mehmet Hakan Morcali

2013-04-01

Full Text Available Present work investigates platinum uptake from synthetically prepared, dilute platinum-bearing solutions using biomass residues, i.e. pistachio nut shell and rice husk, which are abundant in Turkey, and provides a comparison between these two biosorbents. Effects of the different uptake parameters, sorbent dosage, contact time, temperature and pH of solution on platinum uptake (% were studied in detail on a batch sorption. Before the pistachio nut shell was activated, platinum uptake (% was poor compared to the rice husk. However, after the pistachio nut shell was activated at 1000 °C under an argon atmosphere, the platinum uptake (% increased two-fold. The pistachio nut shell (original and activated and rice husk were shown to be better than commercially available activated carbon in terms of adsorption capacity. These two sorbents have also been characterized by FTIR and SEM. Adsorption equilibrium data best complied with the Langmuir isotherm model. Maximum adsorption capacities, Qmax, at 25 °C were found to be 38.31 and 42.02 mg.g- 1for the activated pistachio nut shell and rice husk, respectively. Thermodynamic calculations using the measured ∆H°, ∆S° and ∆G° values indicate that the uptake process was spontaneous and endothermic. The experimental data were shown to be fit the pseudo-second-order kinetic model.

Copper (II) complexes of bidentate ligands exhibit potent anti-cancer activity regardless of platinum sensitivity status.

Science.gov (United States)

Wehbe, Mohamed; Lo, Cody; Leung, Ada W Y; Dragowska, Wieslawa H; Ryan, Gemma M; Bally, Marcel B

2017-12-01

Insensitivity to platinum, either through inherent or acquired resistance, is a major clinical problem in the treatment of many solid tumors. Here, we explored the therapeutic potential of diethyldithiocarbamate (DDC), pyrithione (Pyr), plumbagin (Plum), 8-hydroxyquinoline (8-HQ), clioquinol (CQ) copper complexes in a panel of cancer cell lines that differ in their sensitivity to platins (cisplatin/carboplatin) using a high-content imaging system. Our data suggest that the copper complexes were effective against both platinum sensitive (IC 50  ~ 1 μM platinum) and insensitive (IC 50  > 5 μM platinum) cell lines. Furthermore, copper complexes of DDC, Pyr and 8-HQ had greater therapeutic activity compared to the copper-free ligands in all cell lines; whereas the copper-dependent activities of Plum and CQ were cell-line specific. Four of the copper complexes (Cu(DDC) 2 , Cu(Pyr) 2 , Cu(Plum) 2 and Cu(8-HQ) 2 ) showed IC 50 values less than that of cisplatin in all tested cell lines. The complex copper DDC (Cu(DDC) 2 ) was selected for in vivo evaluation due to its low nano-molar range activity in vitro and the availability of an injectable liposomal formulation. Liposomal (Cu(DDC) 2 ) was tested in a fast-growing platinum-resistant A2780-CP ovarian xenograft model and was found to achieve a statistically significant reduction (50%; p < 0.05) in tumour size. This work supports the potential use of copper-based therapeutics to treat cancers that are insensitive to platinum drugs.

Graphite-supported platinum catalysts: Effects of gas and aqueous phase treatments

Energy Technology Data Exchange (ETDEWEB)

Vleeming, J.H.; Kuster, B.F.M.; Marin, G.B. [Eindhoven Univ. of Technology (Netherlands)] [and others

1997-03-01

The effects on the platinum particle diameter and the available platinum surface area of a graphite-supported platinum catalyst resulting from pretreatments and from performing a selective oxidation reaction are investigated. In the gas phase considerable catalyst sintering occurs only in the presence of oxygen at 773 K due to extensive carbon burn-off, whereas in an aqueous phase platinum particle growth is limited upon oxidative treatment. A hydrogen treatment in aqueous phase at 363 K causes platinum particle growth, aggregate formation, and covering of metal sites. These phenomena become more important with increasing pH. Platinum particle growth and aggregate formation are attributed to platinum particle rather than platinum adatom mobility and is caused by the destruction of the oxygen-containing surface groups on the graphite support, which serve as anchorage sites for the platinum particles. Site covering is caused by products originating from the graphite support, which are formed as a result of the reductive treatments. When performing the aqueous phase oxidation of methyl {alpha}-D-glucopyranoside at 323 K and a pH of 9, catalyst modifications are small under oxidative conditions. Exposure of the catalyst for several hours to methyl {alpha}-D-glucopyranoside under the same conditions but in the absence of oxygen causes site covering. 50 refs., 9 figs., 1 tab.

The role of interleukin-8 (IL-8) and IL-8 receptors in platinum response in high grade serous ovarian carcinoma.

Science.gov (United States)

Stronach, Euan A; Cunnea, Paula; Turner, Christina; Guney, Tankut; Aiyappa, Radhika; Jeyapalan, Senthuran; de Sousa, Camila H; Browne, Alacoque; Magdy, Nesreen; Studd, James B; Sriraksa, Ruethairat; Gabra, Hani; El-Bahrawy, Mona

2015-10-13

Platinum based drugs are the cornerstone of chemotherapy for ovarian cancer, however the development of chemoresistance hinders its success. IL-8 is involved in regulating several pro-survival pathways in cancer. We studied the expression of IL-8 and IL-8 receptors in platinum sensitive and resistant cell lines. Using qRT-PCR and immunohistochemistry, both platinum sensitive (PEA1, PEO14) and resistant (PEA2, PEO23) show increased expression of IL-8 and IL-8 receptors. IL-8RA shows nuclear and cytoplasmic expression, whilst IL-8RB is present solely in the cytoplasm. Knockdown of IL-8 increased sensitivity to cisplatin in platinum sensitive and reversed platinum resistance in resistant cell lines, decreased the expression of anti-apoptotic Bcl-2 and decreased inhibitory phosphorylation of pro-apoptotic Bad. IL-8 receptor antagonist treatment also enhanced platinum sensitivity. Nuclear localisation of IL-8RA was only detected in platinum resistant tumours. Inhibition of IL-8 signalling can enhance response in platinum sensitive and resistant disease. Nuclear IL-8RA may have potential as a biomarker of resistant disease.

Point defects in platinum

International Nuclear Information System (INIS)

Piercy, G.R.

1960-01-01

An investigation was made of the mobility and types of point defect introduced in platinum by deformation in liquid nitrogen, quenching into water from 1600 o C, or reactor irradiation at 50 o C. In all cases the activation energy for motion of the defect was determined from measurements of electrical resistivity. Measurements of density, hardness, and x-ray line broadening were also made there applicable. These experiments indicated that the principal defects remaining in platinum after irradiation were single vacant lattice sites and after quenching were pairs of vacant lattice sites. Those present after deformation In liquid nitrogen were single vacant lattice sites and another type of defect, perhaps interstitial atoms. (author)

Films deposited from reactive sputtering of aluminum acetylacetonate under low energy ion bombardment

Energy Technology Data Exchange (ETDEWEB)

Battaglin, Felipe Augusto Darriba; Prado, Eduardo Silva; Cruz, Nilson Cristino da; Rangel, Elidiane Cipriano, E-mail: elidiane@sorocaba.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Sorocaba, SP (Brazil). Lab. de Plasmas Tecnologicos; Caseli, Luciano [Universidade Federal de Sao Paulo (UNIFESP), Diadema, SP (Brazil). Instituto de Ciencias Ambientais, Quimicas e Farmaceuticas; Silva, Tiago Fiorini da; Tabacniks, Manfredo Harri [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica

2017-07-15

Films were deposited from aluminum acetylacetonate (Al(acac)3 ) using a methodology involving reactive sputtering and low energy ion bombardment. The plasma was generated by the application of radiofrequency power to the powder containing electrode and simultaneously, negative pulses were supplied to the electrode where the substrates were attached. It was investigated the effect of the duty cycle of the pulses (Δ) on the properties of the coatings. Association of ion bombardment to the deposition process increased film thickness, structure reticulation and organic content. Ions from the deposition environment were implanted at the film-air interface or underneath it. Morphology and topography were altered depending on Δ. Considering the enhancement of Δ, it affected the flux of ions reaching the depositing interface and then the deposition rate, H content, crosslinking degree and surface microstructure. Alumina groups were detected in the infrared spectra, whereas the precipitation of amorphous alumina was confirmed by X-ray diffraction. (author)

Photocatalytic self-cleaning cotton fabrics with platinum (IV) chloride modified TiO{sub 2} and N-TiO{sub 2} coatings

Energy Technology Data Exchange (ETDEWEB)

Long, Mingce, E-mail: long_mc@sjtu.edu.cn [School of Environmental Science and Engineering, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai, 200240 (China); Key Laboratory for Thin Film and Microfabrication of the Ministry of Education, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai, 200240 (China); Zheng, Longhui; Tan, Beihui [School of Environmental Science and Engineering, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai, 200240 (China); Shu, Heping [Xiaoxi New Materials Science and Technology (Shanghai) Co. Ltd., 655 Cangyuan Road, Shanghai, 200240 (China)

2016-11-15

Highlights: • Platinum (IV) chloride modified TiO{sub 2} and N-TiO{sub 2} nanosols are synthesized. • Pt-TiO{sub 2} coatings display enhanced performance in the degradation of MO and stains. • Surface attached PtCl{sub 6}{sup 2−} enable visible light activity of TiO{sub 2} coated cotton fabric. - Abstract: To enable photocatalytic self-cleaning cotton fabrics working under visible light irradiation, platinum (IV) chloride modified TiO{sub 2} (Pt-TiO{sub 2}) and N-TiO{sub 2} (Pt-N-TiO{sub 2}) nanosols are synthesized through a low temperature precipitation-peptization method. According to the characterizations of XRD, DRS and TEM, all nanoparticles are anatase nanocrystallites in the sizes of less than 10 nm, while N-TiO{sub 2} nanoparticles have better crystallization and smaller sizes. However, the cotton fabrics functionalized with Pt-TiO{sub 2} display significantly enhanced photocatalytic activity for methyl orange degradation and coffee stain removal under both solar simulator and visible light irradiation, while the performance of that coatings of Pt-N-TiO{sub 2} is poor. Further XRF and XPS results indicate that surface species on N-TiO{sub 2} block the adsorption of PtCl{sub 6}{sup 2−} anions, whereas these anions strongly attach on the surface of TiO{sub 2} nanoparticles, and accordingly enable functionalized cotton fabrics efficient visible light driven activities based on a mechanism of charge transfer from ligand to metal (CTLM) excitation.

Platinum uptake by the freshwater isopod Asellus Aquaticus in urban rivers

Energy Technology Data Exchange (ETDEWEB)

Rauch, S.; Morrison, G.M. [Department of Sanitary Engineering, Chalmers University of Technology, S-412 96 Goeteborg (Sweden)

1999-09-01

Platinum has been increasing in the environment as a result of emissions from catalytic converters. The platinum emitted is principally located in the vicinity of roads but might be transported to urban rivers through highway and urban run-off water. Platinum concentrations in the freshwater isopod Asellus aquaticus were measured for two urban rivers and a stormwater detention pond. Concentrations ranged from 0.04 to 12.4 {mu}g g{sup -1} for direct analysis and from 0.16 to 4.5 {mu}g g{sup -1} after depuration. Analyses of water, pore water and sediments indicate that platinum in urban rivers is mostly found in the sediments and these provide the major contribution of platinum to Asellus aquaticus. Exposure experiments showed the importance of platinum speciation for uptake.

Determination of phosphorus traces in platinum alloys by two-phase isotope exchange

International Nuclear Information System (INIS)

Vlacil, F.

1980-01-01

The method of ZEMAN and KRATZER for the determination of phosphorus traces by means of two-phase isotope exchange was modified for the determination of phosphorus in pure platinum or pure platinum alloys. It was found that Pt, Rh, Ag and As do not interfere with the determination. Among the elements usually present in platinum metal or platinum alloys, only gold interferes. It was removed by extraction from 7M HCl by MIBK and AmOAc. Hydrochloric acid also interferes but it can be removed by evaporation. The analytical procedure is given for the solution obtained by pressure decomposition of the sample (0.5 g) in a steel bomb with PTFE inlay. It is possible to determine > 2 ppm P (approximate error -10%). If using calibration dependence instead of the well known equation for isotope exchange it is not necessary to know the content of P in the standard solution labelled with 32 P. (author)

A microscale synthesis of a promising radiolabelled antitumor drug: cis-1,1-cyclobutanedicarboxylato (2R)-2-methyl-1,4-butanediamine platinum(II), NK121

International Nuclear Information System (INIS)

Suwa, Masato; Kogawa, Osamu; Hashimoto, Yutaka

1992-01-01

A promising antitumor drug, cis-1,1-cyclobutane-dicarboxylato (2R)-2-methyl-1,4-butanediamine platinum (II), NK121, was synthesized from radionuclides of platinum such as 193m Pt, 195m Pt and 191 Pt which were produced by neutron irradiation of enriched 192 Pt. The overall yield was 38.6% in a synthesis time of 10 hours. The radioactivities present in 8.39 mg of NK121 were 115.3 μCi as 193m Pt, 29.9 μCi as 197 Pt, 22.0 μCi as 195m Pt, and 4.8 μCi as 191 Pt at the end of synthesis. The specific activity of the NK121 was 13.7 μCi ( 193m Pt)/mg NK121 at the end of synthesis. The radiochemical purity of NK121 was typically 99%. HPLC analyses confirmed that NK121 was in an adequate chemical purity and suitable for animal experimentation. (author)

A microscale synthesis of a promising radiolabelled antitumor drug: cis-1,1-cyclobutanedicarboxylato (2R)-2-methyl-1,4-butanediamine platinum(II), NK121

Energy Technology Data Exchange (ETDEWEB)

Suwa, Masato; Kogawa, Osamu; Hashimoto, Yutaka (Nippon Kayaku Co. Ltd., Tokyo (Japan). Research Labs. of Pharmaceuticals Group); Nowatari, Hiroyoshi (Nippon Kayaku Co. Ltd., Takasaki, Gumma (Japan). Takasaki Research Labs.); Murase, Yuko; Homma, Yoshio (Kyoritsu Coll. of Pharmacy, Tokyo (Japan))

1992-05-01

A promising antitumor drug, cis-1,1-cyclobutane-dicarboxylato (2R)-2-methyl-1,4-butanediamine platinum (II), NK121, was synthesized from radionuclides of platinum such as {sup 193m}Pt, {sup 195m}Pt and {sup 191}Pt which were produced by neutron irradiation of enriched {sup 192}Pt. The overall yield was 38.6% in a synthesis time of 10 hours. The radioactivities present in 8.39 mg of NK121 were 115.3 {mu}Ci as {sup 193m}Pt, 29.9 {mu}Ci as {sup 197}Pt, 22.0 {mu}Ci as {sup 195m}Pt, and 4.8 {mu}Ci as {sup 191}Pt at the end of synthesis. The specific activity of the NK121 was 13.7 {mu}Ci ({sup 193m}Pt)/mg NK121 at the end of synthesis. The radiochemical purity of NK121 was typically 99%. HPLC analyses confirmed that NK121 was in an adequate chemical purity and suitable for animal experimentation. (author).

Pretreatment of Platinum/Tin Oxide-Catalyst

Science.gov (United States)

Hess, Robert V.; Paulin, Patricia A.; Miller, Irvin M.; Schryer, David R.; Sidney, Barry D.; Wood, George M.; Upchurch, Billy T.; Brown, Kenneth G.

1987-01-01

Addition of CO to He pretreatment doubles catalytic activity. In sealed, high-energy, pulsed CO2 laser, CO and O2 form as decomposition products of CO2 in laser discharge zone. Products must be recombined, because oxygen concentration of more than few tenths of percent causes rapid deterioration of power, ending in unstable operation. Promising low-temperature catalyst for combining CO and O2 is platinum on tin oxide. New development increases activity of catalyst so less needed for recombination process.

A Change to the Platinum Publications | Poster

Science.gov (United States)

Please be advised that the Poster will no longer publish the “Platinum Publications” series listing recent NCI at Frederick publications. All published research represents a valuable addition to the fight against cancer, AIDS, and infectious diseases—thus, the “Platinum Publications” did not adequately commend all of the important work done by NCI at Frederick researchers.

Novel 3-(aminomethyl)naphthoquinone mannich base-platinum(IV) complexes: synthesis, characterization, electrochemical and cytotoxic studies

Energy Technology Data Exchange (ETDEWEB)

Silva, Gustavo B. da; Neves, Amanda P.; Vargas, Maria D., E-mail: mdvargas@vm.uff.br [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Instituto de Quimica; Alves, Wagner A. [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Seropedica, RJ (Brazil). Departamento de Quimica; Marinho-Filho, Jose D.B.; Pessoa, Claudia; Moraes, Manoel O.; Costa-Lotufo, Leticia V. [Universidade Federal do Ceara (UFCE), Fortaleza, CE (Brazil). Centro de Ciencias da Saude. Departamento de Fisiologia e Farmacologia

2013-04-15

Three novel platinum(IV) complexes cis,cis,trans-[Pt(HL1-3)Cl{sub 2}(OH){sub 2}] 1b-3b(HL = 2-hydroxy-3-[(R{sup 1} -amino)(pyridin-2-yl)methyl]-1,4-naphthoquinone, R{sup 1} = n-butyl, HL1; n-heptyl, HL2 and n-decyl, HL3) have been obtained from the oxidation of the respective precursors cis-[Pt(HL1-3)Cl{sub 2}] 1a-3a. Cyclic voltammetry studies of 1b-3b in MeCN showed the quasi reversible naphthoquinonate (NQO{sup -}, i.e., L{sup -}) redox process and irreversible process attributed to the reduction of the Pt{sup 4+}/Pt{sup 2+} pair, at potentials about 400 mV less negative than for the cisplatin precursor cis,cis,trans-[Pt(NH{sub 3}){sub 2}Cl{sub 2}(OH){sub 2}]. Hydrogen bond interaction between the naphthoquinone 2-hydroxyl group and an axially coordinated hydroxide ligand in 1b-3b has been proposed to favor the Pt{sup 4+}/Pt{sup 2+} reduction. The cytotoxicity studies against four human cancer cell lines have shown that in general the platinum(IV) and platinum(II)derivatives exhibit the same cytotoxic profile and are all more active than cisplatin. The lowest in vitro IC{sub 50} values have been observed for 2b-3b, which bear ligands with the largest R{sup 1} groups (HL2-HL3) being the most lipophilic. Furthermore similar IC{sub 50} values for platinum(II) and platinum(IV) complexes of the same ligands have been associated with rapid in vitro reduction of the latter complexes to afford 1a-3a. (author)

Textured strontium titanate layers on platinum by atomic layer deposition

International Nuclear Information System (INIS)

Blomberg, T.; Anttila, J.; Haukka, S.; Tuominen, M.; Lukosius, M.; Wenger, Ch.; Saukkonen, T.

2012-01-01

Formation of textured strontium titanate (STO) layers with large lateral grain size (0.2–1 μm) and low X-ray reflectivity roughness (∼ 1.36 nm) on Pt electrodes by industry proven atomic layer deposition (ALD) method is demonstrated. Sr(t-Bu 3 Cp) 2 , Ti(OMe) 4 and O 3 precursors at 250 °C were used to deposit Sr rich STO on Pt/Ti/SiO 2 /Si ∅200 mm substrates. After crystallization post deposition annealing at 600 °C in air, most of the STO grains showed a preferential orientation of the {001} plane parallel to the substrate surface, although other orientations were also present. Cross sectional and plan view transmission electron microscopy and electron diffraction analysis revealed more than an order of magnitude larger lateral grain sizes for the STO compared to the underlying multicrystalline {111} oriented platinum electrode. The combination of platinum bottom electrodes with ALD STO(O 3 ) shows a promising path towards the formation of single oriented STO film. - Highlights: ► Amorphous strontium titanate (STO) on platinum formed a textured film after annealing. ► Single crystal domains in 60 nm STO film were 0.2–1 μm wide. ► Most STO grains were {001} oriented.

Dissolution of Platinum in Hydrochloric Acid Under Industrial-Scale Alternating Current Polarization

Science.gov (United States)

Myrzabekov, B. E.; Bayeshov, A. B.; Makhanbetov, A. B.; Mishra, B.; Baigenzhenov, O. S.

2018-02-01

The electrochemical behavior of platinum in a hydrochloric acid solution under polarization by an industrial-scale alternating current has been investigated. For the electrical dissolution of platinum, titanium is used as an auxiliary electrode, which increases the yield of platinum dissolution by 12.5 pct. The influence of the concentration of hydrochloric acid, the current densities of the platinum and titanium electrodes, and the temperature of the electrolyte on the efficiency of the process of dissolving platinum have all been studied.

Exposure of the German general population to platinum and rhodium - Urinary levels and determining factors.

Science.gov (United States)

Munker, Sven; Kilo, Sonja; Röß, Christoph; Jeitner, Peter; Schierl, Rudolf; Göen, Thomas; Drexler, Hans

2016-11-01

In this study the exposure of the general population in Germany to platinum and rhodium and its determinants was investigated in 259 participants (subdivided in three groups) by urine analyses and assessment of the dental status. Complementary, an interview including questions characterising possible exposure to traffic exhaust was conducted. The median excretion was 2.42ng platinum/g creatinine and 7.27ng rhodium/g creatinine. The detailed analysis of the collected data showed significant higher platinum excretion values with increasing number of surfaces covered with restorations containing precious metals (R=0.389; prhodium excretion values (median=7.27ng/g; 95th percentile=13.5 ng/g). In summary, the study showed that exhaust emissions have an influence on platinum and rhodium excretion, but for platinum this influence is rather low compared to the influence of precious metals containing restorations. Copyright © 2016 Elsevier GmbH. All rights reserved.

Preparation of platinum/iridium scanning probe microscopy tips

DEFF Research Database (Denmark)

Sørensen, Alexis Hammer; Hvid, U.; Mortensen, M.W.

1999-01-01

oxide layer. In order to explain the relatively high etching rates observed for the otherwise noble metal platinum we suggest that besides anodic corrosion of the platinum by the electrolyte containing chloride ions, a different etching mechanism causes a substantial increase of the etching rate...

Modeling of Platinum-Aryl Interaction with Amyloid-β Peptide.

Science.gov (United States)

Turner, Matthew; Platts, James A; Deeth, Robert J

2016-03-08

Ligand field molecular mechanics (LFMM), density functional theory (DFT), and semiempirical PM7 methods are used to study the binding of two Pt(II)-L systems to an N-terminal fragment of the amyloid-β peptide, where L = 2,2-bipyridyl or 1,10-phenanthroline. Molecular dynamics simulations are used to explore the conformational freedom of the peptide using LFMM combined with AMBER molecular mechanics parameters. We establish a modeling protocol, allowing for identification and analysis of favorable platinum-binding modes and peptide conformations. Preferred binding modes are identified for each ligand investigated; metal coordination occurs via Nε in His residues for both ligands--His6ε-His13ε and His6ε-His14ε for the bipyridyl and phenanthroline ligands, respectively. The observed change in binding mode for the different ligands suggests that the binding mode of these platinum-based structures can be controlled by the choice of ligand. In the bipy systems, Boltzmann population at 310 K is dominated by a single conformer, while in the phenanthroline case, three conformations make significant contributions to the ensemble. The relative stability of these conformations is due to the inherent stability of binding platinum via Nε in addition to subtle H-bonding effects.

On the mobility of carbon-supported platinum nanoparticles towards unveiling cathode degradation in water electrolysis

Science.gov (United States)

Paciok, Paul; Schalenbach, Maximilian; Carmo, Marcelo; Stolten, Detlef

2017-10-01

This study investigates the influence of the hydrogen evolution reaction (HER) overpotential on the mobility of carbon-supported platinum particles. The migration of the platinum over the carbon support was analyzed by means of identical location transmission electron microscopy (IL-TEM). While at potentials of 0.1 and 0 V vs. reversible hydrogen electrode (RHE), no changes to the Pt/C material were observed. With a decrease of the overpotential to -0.1 V vs. RHE, an increase in the quantity of migrating platinum particles took place. At -0.2 V vs. RHE, a further rise in the particle migration was observed. The effect of the overpotential on the migration was explained by a higher hydrogen generation rate, the formation of a hydrogen monolayer on the platinum and the resulting changes of the platinum support distance. The mechanisms revealed in this study could describe a relevant source of degradation of PEM water electrolyzers.

Silica Supported Platinum Catalysts for Total Oxidation of the Polyaromatic Hydrocarbon Naphthalene: An Investigation of Metal Loading and Calcination Temperature

Directory of Open Access Journals (Sweden)

David R. Sellick

2015-04-01

Full Text Available A range of catalysts comprising of platinum supported on silica, prepared by an impregnation method, have been studied for the total oxidation of naphthalene, which is a representative Polycyclic Aromatic Hydrocarbon. The influence of platinum loading and calcination temperature on oxidation activity was evaluated. Increasing the platinum loading up to 2.5 wt.% increased the catalyst activity, whilst a 5.0 wt.% catalyst was slightly less active. The catalyst containing the optimum 2.5 wt.% loading was most active after calcination in air at 550 °C. Characterisation by carbon monoxide chemisorption and X-ray photoelectron spectroscopy showed that low platinum dispersion to form large platinum particles, in combination with platinum in metallic and oxidised states was important for high catalyst activity. Catalyst performance improved after initial use in repeat cycles, whilst there was slight deactivation after prolonged time-on-stream.

Nanofiber-deposited porous platinum enables glucose fuel cell anodes with high current density in body fluids

Science.gov (United States)

Frei, Maxi; Erben, Johannes; Martin, Julian; Zengerle, Roland; Kerzenmacher, Sven

2017-09-01

The poisoning of platinum anodes by body-fluid constituents such as amino acids is currently the main hurdle preventing the application of abiotic glucose fuel cells as battery-independent power supply for medical implants. We present a novel anode material that enables continuous operation of glucose oxidation anodes in horse serum for at least 30 days at a current density of (7.2 ± 1.9) μA cm-2. The fabrication process is based on the electro-deposition of highly porous platinum onto a 3-dimensional carbon nanofiber support, leading to approximately 2-fold increased electrode roughness factors (up to 16500 ± 2300). The material's superior performance is not only related to its high specific surface area, but also to an improved catalytic activity and/or poisoning resistance. Presumably, this results from the micro- and nanostructure of the platinum deposits. This represents a major step forward in the development of implantable glucose fuel cells based on long-term stable platinum electrodes.

Phase-field model for deposition process of platinum nanoparticles on carbon substrate

International Nuclear Information System (INIS)

Yamakawa, S; Hyodo, S; Okazaki-Maeda, K; Kohyama, M

2008-01-01

Platinum supported on a carbon carrier is widely used as a catalyst for polymer electrolyte membrane fuel cells. The catalytic activity is significantly affected by the size distribution and morphologies of the platinum particles. The objective of this study is to extend the phase-field approach to describe the formation process of platinum particles onto the substrate. The microstructural evolution of a nanoparticle was represented by the temporal evolution of the field variables related to the platinum concentration, long-range crystallographic ordering and phase transition. First-principles calculations were performed in order to estimate the interaction energies between several different types of platinum clusters and a graphene sheet. The platinum density profile concentrated over the substrate surface led to the formation of three-dimensional islands in accordance with the Volmer-Weber mode of growth. The size distributions of the platinum particles were sensitive to the heterogeneity of the substrate surface and to the competitive nucleation and growth processes

An impending platinum crisis and its implications for the future of the automobile

International Nuclear Information System (INIS)

Yang, C.-J.

2009-01-01

The global demand for platinum has consistently outgrown supply in the past decade. This trend likely will continue and the imbalance may possibly escalate into a crisis. Platinum plays pivotal roles in both conventional automobile emissions control and the envisioned hydrogen economy. A platinum crisis would have profound implications on energy and environment. On the one hand, inadequate platinum supply will prevent widespread commercialization of hydrogen fuel-cell vehicles. On the other hand, expensive platinum may enhance the competitiveness of hybrid, plug-in hybrid, and battery-powered electric cars. Policymakers should weigh the potential impacts of a platinum crisis in energy policy.

Oxygen reduction using platinum electrocatalysts prepared by liquid phase photo-deposition; Reduccion de oxigeno mediante electrocatalizadores de platino preparados por foto-deposicion en fase liquida

Energy Technology Data Exchange (ETDEWEB)

Ruiz-Camacho, B.; Perez-Galindo, J. A.; Valenzuela, M. A.; Gonzalez-Huerta, R. G. [Instituto Politecnico Nacional, ESIQIE, Mexico D.F. (Mexico)]. E-mail: rosgonzalez_h@yahoo.com.mx

2009-09-15

This work presents the synthesis and characterization of nanometric-sized Pt/C electrochemical catalysts using impregnation and liquid phase photo-deposition methods. Two platinum precursors were used, C{sub 10}H{sub 14}O{sub 4}Pt (Pt acetylacetonate, Pt(acac){sub 2}) and H{sub 2}PtCl{sub 6} (hexachloroplatinic acid) to study the effect on the particle size and the electrocatalytic behavior in the oxygen reduction reaction. The characterization of the catalysts was done using x-ray diffraction, hydrogen chemisorption and transmission electron microscopy. The electrochemical study was conducted with cyclic voltamperometry and rotary disc electrode (RDE) techniques. Pt (E-tek) was used as a reference catalyst. The peaks of the platinum were identified based on the x-ray diffraction results, and correspond to crystalline phases (111) and (200), whose intensity was greater when using H{sub 2}PtCl{sub 6} versus Pt(acac){sub 2}. The hydrogen chemisorption and transmission electron microscopy tests found that the larger-sized particle (1-5 nm) and greater metallic dispersion was obtained using Pt(acac){sub 2} as a platinum precursor and liquid phase photo-deposition. It was also found that this material presented the best electrochemical response, showing a open-circuit potential of 0.96 V and over-potential of 0.05 V with respect to H{sub 2}PtCl{sub 6} and of 0.22 V with respect to the catalyst obtained using impregnation. [Spanish] En este trabajo se presenta la sintesis y caracterizacion electroquimica de catalizadores de tamano nanometrico de Pt/C empleando los metodos de impregnacion y foto-deposicion en fase liquida. Se utilizaron dos precursores del platino C{sub 10}H{sub 14}O{sub 4}Pt (acetil-acetonato de Pt, Pt(acac){sub 2}) y H2PtCl6 (acido hexacloroplatinico), para estudiar el efecto que tienen sobre el tamano de particula y el comportamiento electrocatalitico en la reaccion de reduccion de oxigeno. La caracterizacion de los catalizadores se realizo mediante

Platinum boride nanowires: Synthesis and characterization

International Nuclear Information System (INIS)

Ding Zhanhui; Qiu Lixia; Zhang Jian; Yao Bin; Cui Tian; Guan Weiming; Zheng Weitao; Wang Wenquan; Zhao Xudong; Liu Xiaoyang

2012-01-01

Highlights: ► Platinum boride nanowires have been synthesized via the direct current arc discharge method. ► XRD, TEM and SAED indicate that the nanowires are single-crystal PtB. ► Two broad photoluminescence emission peaks at about 586 nm and 626 nm have been observed in the PL spectroscopy of PtB nanowires. - Abstract: Platinum boride (PtB) nanowires have been successfully fabricated with direct current arc discharge method using a milled mixture of platinum (Pt) and boron nitride (BN) powders. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the compositions, morphology, and structures of the samples. The results show that PtB nanowires are 30–50 nm thick and 20–30 μm long. TEM and selected area electron diffraction (SAED) patterns identify that the PtB nanowires are single-crystalline in nature. A growth mechanism based on vapor–liquid–solid (VLS) process is proposed for the formation of nanowires.

Urinary excretion of platinum, arsenic and selenium of cancer patients from the Antofagasta region in Chile treated with platinum-based drugs

Directory of Open Access Journals (Sweden)

Román Domingo A

2012-04-01

Full Text Available Abstract Background Arsenic exposure increases the risk of non-cancerous and cancerous diseases. In the Antofagasta region in Chile, an established relationship exists between arsenic exposure and the risk of cancer of the bladder, lung and skin. Platinum-based drugs are first-line treatments, and many works recognise selenium as a cancer-fighting nutrient. We characterised the short-term urinary excretion amounts of arsenic, selenium and platinum in 24-h urine samples from patients with lung cancer and those with cancer other than lung treated with cisplatin or/and carboplatin. As - Se - Pt inter-element relationships were also investigated. Results The amounts of platinum excreted in urine were not significantly different between patients with lung cancer and those with other cancers treated with cisplatin, despite the significant variation in platinum amounts supplied from platinum-based drugs. In general, the analytical amounts of excreted selenium were greater than those for arsenic, which could imply that platinum favours the excretion of selenium. For other types of cancers treated with drugs without platinum, excretion of selenium was also greater than that of arsenic, suggesting an antagonist selenium-anti-cancer drug relationship. Conclusions Regards the baseline status of patients, the analytical amounts of excreted Se is greater than those for As, particularly, for cisplatin chemotherapy. This finding could imply that for over the As displacement Pt favours the excretion of Se. The analytical amounts of excreted Se were greater than those for As, either with and without Pt-containing drugs, suggesting an antagonist Se-anti-cancer drug relationship. However, it seemed that differences existed between As - Se - Pt inter-element associations in patients treated for lung cancer in comparison with those treated for cancer other than lung. Therefore, knowledge obtained in this work, can contribute to understanding the arsenic cancer

Atomic absorption spectrophotometric determination of microamounts of beryllium in aluminum and copper using solvent extraction with acetylacetone

International Nuclear Information System (INIS)

Matsusaki, Koji

1975-01-01

A sensitive method for the determination of microamounts of beryllium in aluminum and copper by atomic absorption spectrophotometry using the methylisobutylketone (MIBK) extraction with acetylacetone (AA) was investigated. An aqueous sample solution containing (0.5--5)μg of beryllium and less than 100 mg of aluminum or less than 500 mg of copper was taken into a 100-ml separation funnel, and 2 ml of 5% AA, 20 mg of EDTA for 1 mg of aluminum or 8.8 mg of EDTA for 1 mg of copper, and 10 ml of saturated NaCl solution were added. The pH was adjusted to 5--7 with 10 ml of 2 M NaCH 3 COO-CH 3 COOH buffer, and the solution was diluted to 50 ml. After 10 minutes, the solution was shaken for 2 minutes with 10 ml of MIBK. The organic phase was introduced into a nitrous oxide-acetylene flame and the absorption measured at 234.9 nm against a reagent blank. None of metal elements interfered with the determination of beryllium, and beryllium above 0.001% in aluminum, and above 0.0002% in copper was determined. This method was successfully applied to the determination of beryllium in aluminum and copper alloys. (auth.)

Structure of the Hydrated Platinum(II) Ion And the Cis-Diammine-Platinum(II) Complex in Acidic Aqueous Solution: An EXAFS Study

Energy Technology Data Exchange (ETDEWEB)

Jalilehvand, F.; Laffin, L.J.

2009-05-18

Careful analysis of Pt L{sub 3}-edge extended X-ray absorption fine structure (EXAFS) spectra shows that the hydrated platinum(II) ion in acidic (HClO{sub 4}) aqueous solution binds four water molecules with the Pt-O bond distance 2.01(2) {angstrom} and one (or two) in the axial position at 2.39(2) {angstrom}. The weak axial water coordination is in accordance with the unexpectedly small activation volume previously reported for water exchange in an interchange mechanism with associative character. The hydrated cis-diammineplatinum(II) complex has a similar coordination environment with two ammine and two aqua ligands strongly bound with Pt-O/N bond distances of 2.01(2) {angstrom} and, in addition, one (or two) axial water molecule at 2.37(2) {angstrom}. This result provides a new basis for theoretical computational studies aiming to connect the function of the anticancer drug cis-platin to its ligand exchange reactions, where usually four-coordinated square planar platinum(II) species are considered as the reactant and product. {sup 195}Pt NMR spectroscopy has been used to characterize the Pt(II) complexes.

Preparation of transparent sol-gel films containing europium, terbium, and ytterbium cations from 4-(3'-triethoxysilylpropylimino)pent-2-en-2-ol

International Nuclear Information System (INIS)

Semenov, V.V.; Cherepennikova, N.F.; Kuznetsova, O.V.; Melenskova, N.V.; Bushuk, B.A.; Bushuk, S.B.; Kal'vinkovskaya, Yu.A.; Duglas, V.E.

2007-01-01

A reaction of 3-aminopropyl(triethoxy)silane with acetylacetone gave a mixture of two isomeric carbon-functionalized organosilicon compounds capable of complexation and sol-gel polymerization. These were 4-(3'-triethoxysilylpropylimino)pent-2-en-2-ol (EtO) 3 Si-CH 2 CH 2 CH 2 -N=C(Me)CH=C(Me)OH (Ia, 83%) and 4-(3'-triethoxysilylpropylamino)pent-3-en-2-one (EtO) 3 Si-CH 2 CH 2 CH 2 -NH-C(Me)=CH-C(O)Me (Ib, 17%). With acetylacetone trimethylsilyl ether instead of acetylacetone itself, compound Ia and silylated derivatives (Me 3 SiO) n (EtO) 3-n Si-CH 2 CH 2 CH 2 -N=C(Me)CH=C(Me)OH were obtained as admixture in 84 and 16% yields, respectively. Reactions of ligands Ia and Ib with europium and terbium propan-2-olates afforded the corresponding complexes. Formulations of lanthanide complexes, oligodimethylsiloxanediols, and 3-aminopropyl(triethoxy)silane were used to prepare transparent sol-gel films. The photoluminescence spectra of the films show narrow bands due to Eu 3+ or Tb 3+ emission. Emission from the organosilicon matrix appears as a broad band at 430 to 435 nm [ru

Platinum coat color in red fox (Vulpes vulpes) is caused by a mutation in an autosomal copy of KIT.

Science.gov (United States)

Johnson, J L; Kozysa, A; Kharlamova, A V; Gulevich, R G; Perelman, P L; Fong, H W F; Vladimirova, A V; Oskina, I N; Trut, L N; Kukekova, A V

2015-04-01

The red fox (Vulpes vulpes) demonstrates a variety of coat colors including platinum, a common phenotype maintained in farm-bred fox populations. Foxes heterozygous for the platinum allele have a light silver coat and extensive white spotting, whereas homozygosity is embryonic lethal. Two KIT transcripts were identified in skin cDNA from platinum foxes. The long transcript was identical to the KIT transcript of silver foxes, whereas the short transcript, which lacks exon 17, was specific to platinum. The KIT gene has several copies in the fox genome: an autosomal copy on chromosome 2 and additional copies on the B chromosomes. To identify the platinum-specific KIT sequence, the genomes of one platinum and one silver fox were sequenced. A single nucleotide polymorphism (SNP) was identified at the first nucleotide of KIT intron 17 in the platinum fox. In platinum foxes, the A allele of the SNP disrupts the donor splice site and causes exon 17, which is part of a segment that encodes a conserved tyrosine kinase domain, to be skipped. Complete cosegregation of the A allele with the platinum phenotype was confirmed by linkage mapping (LOD 25.59). All genotyped farm-bred platinum foxes from Russia and the US were heterozygous for the SNP (A/G), whereas foxes with different coat colors were homozygous for the G allele. Identification of the platinum mutation suggests that other fox white-spotting phenotypes, which are allelic to platinum, would also be caused by mutations in the KIT gene. © 2015 Stichting International Foundation for Animal Genetics.

The RSC Faraday prize lecture of 1989 on platinum.

Science.gov (United States)

Thomas, John Meurig

2017-08-25

In 1861, Michael Faraday gave one of his last Friday Evening Discourses at the Royal Institution of Great Britain, London, on platinum, which he described as "this beautiful, magnificent and valuable metal". More than a hundred and twenty years later (in 1989), the author re-enacted, at the Royal Institution, many of the demonstrations that Faraday carried out in his memorable Discourse. This article outlines many of Faraday's views on, and experiments with, platinum. It also describes the continuing importance and utilization of platinum, both as perceived in 1989 and from present perspectives.

A new [(1R,2R)-1,2-diaminocyclohexane]platinum(II) complex: formation by nitrate-acetonitrile ligand exchange

Czech Academy of Sciences Publication Activity Database

Pažout, R.; Housková, J.; Dušek, Michal; Maixner, J.; Cibulková, J.; Kačer, P.

2010-01-01

Roč. 66, Part 10 (2010), m273-m275 ISSN 0108-2701 Institutional research plan: CEZ:AV0Z10100521 Keywords : platinum complexes * structure analysis * disorder * cyclohexane * diamine Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.745, year: 2010

Single-Atom Catalyst of Platinum Supported on Titanium Nitride for Selective Electrochemical Reactions.

Science.gov (United States)

Yang, Sungeun; Kim, Jiwhan; Tak, Young Joo; Soon, Aloysius; Lee, Hyunjoo

2016-02-05

As a catalyst, single-atom platinum may provide an ideal structure for platinum minimization. Herein, a single-atom catalyst of platinum supported on titanium nitride nanoparticles were successfully prepared with the aid of chlorine ligands. Unlike platinum nanoparticles, the single-atom active sites predominantly produced hydrogen peroxide in the electrochemical oxygen reduction with the highest mass activity reported so far. The electrocatalytic oxidation of small organic molecules, such as formic acid and methanol, also exhibited unique selectivity on the single-atom platinum catalyst. A lack of platinum ensemble sites changed the reaction pathway for the oxygen-reduction reaction toward a two-electron pathway and formic acid oxidation toward direct dehydrogenation, and also induced no activity for the methanol oxidation. This work demonstrates that single-atom platinum can be an efficient electrocatalyst with high mass activity and unique selectivity. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Levels and Speciation of Platinum in Size-Fractionated Atmospheric Aerosol in Urban and Rural Sites across Europe

Science.gov (United States)

Shafer, Martin; Antkiewicz, Dagmara; Overdier, Joel; Schauer, James

2016-04-01

In this study we characterized the levels and speciation of platinum in a unique set of size-resolved atmospheric aerosol (PM) samples obtained from urban environments across Europe. From April-July 2012 we collected PM from roadside canyon, roadside motorway, and background urban sites in each of six European cities (Amsterdam, Frankfurt, London, Milan, Stockholm, and Thessaloniki). A Hi-Vol sampler was used to collect PM in three size classes (>PM7, PM7-PM3, PM3) and characterized for total platinum, soluble platinum (in a suite of physiologically relevant fluids - lung fluid (ALF), Gambles saline, 0.07M HCl, and MQ) and speciated forms (colloidal and anionic) within the soluble fractions. In addition we measured 50 other elements by SF-ICPMS, soluble ions by IC, and soluble organic carbon in the PM. Order-of-magnitude differences in air concentrations of total platinum were observed between urban sites, ranging from 4 to over 45 pg/m3; with a median level of 6 pg/m3. When platinum concentrations are normalized to PM mass the cross Europe and site-to-site variability was substantially reduced - a 3-fold variation from 200 to 600 ng/g was observed. Roadside canyon sites in London, Stockholm and Thessaloniki exhibited the highest concentrations; however levels at urban background sites were remarkably similar across the cities. Relatively consistent and low concentrations (1 to 2 pg/m3) of total platinum were observed at rural background sites across Europe. The contribution of coarse particles (>7 micron and 7-3 micron) to air concentrations of total platinum was very significant (>35% at nearly all sites). Soluble platinum fractions ranged from 2 to 6% (MQ to HCl) in rural background sites to 5 to 20% (MQ to HCl) in roadway canyon sites in London and Thessaloniki; with the extractable platinum fractions a strong function of pH. With the exception of urban canyon sites in London and Thessaloniki, soluble platinum concentrations in the fine aerosol (PM3) were all

DNA polymerase η modulates replication fork progression and DNA damage responses in platinum-treated human cells

Science.gov (United States)

Sokol, Anna M.; Cruet-Hennequart, Séverine; Pasero, Philippe; Carty, Michael P.

2013-11-01

Human cells lacking DNA polymerase η (polη) are sensitive to platinum-based cancer chemotherapeutic agents. Using DNA combing to directly investigate the role of polη in bypass of platinum-induced DNA lesions in vivo, we demonstrate that nascent DNA strands are up to 39% shorter in human cells lacking polη than in cells expressing polη. This provides the first direct evidence that polη modulates replication fork progression in vivo following cisplatin and carboplatin treatment. Severe replication inhibition in individual platinum-treated polη-deficient cells correlates with enhanced phosphorylation of the RPA2 subunit of replication protein A on serines 4 and 8, as determined using EdU labelling and immunofluorescence, consistent with formation of DNA strand breaks at arrested forks in the absence of polη. Polη-mediated bypass of platinum-induced DNA lesions may therefore represent one mechanism by which cancer cells can tolerate platinum-based chemotherapy.

Bimetallic alloy electrocatalysts with multilayered platinum-skin surfaces

Science.gov (United States)

Stamenkovic, Vojislav R.; Wang, Chao; Markovic, Nenad M.

2016-01-26

Compositions and methods of preparing a bimetallic alloy having enhanced electrocatalytic properties are provided. The composition comprises a PtNi substrate having a surface layer, a near-surface layer, and an inner layer, where the surface layer comprises a nickel-depleted composition, such that the surface layer comprises a platinum skin having at least one atomic layer of platinum.

Ruthenium-platinum bimetallic catalysts supported on silica: characterization and study of benzene hydrogenation and CO methanation

Energy Technology Data Exchange (ETDEWEB)

Chakrabarty, D.K.; Rao, K.M.; Sundararaman, N.; Chandavar, K.

1986-12-15

Ru-Pt/SiO/sub 2/ bimetallic catalysts with varying Ru:Pt ratio have been prepared and studied with the aim to establish if they contain coclusters or isolated ruthenium and platinum particles. X-ray diffraction studies show that individual crystallites of ruthenium and platinum are present and no coclusters are formed. Metal dispersion has been determined by hydrogen chemisorption and surface composition of the catalysts has been obtained from XPS. It was found that preoxidation of the catalysts prior to reduction is essential for good platinum dispersion. The experimental turnover number (TN) for benzene hydrogenation on the bimetallic catalysts agrees very well with that of the weighted average on the individual metal catalysts and this may be taken as a kinetic evidence for the absence of coclusters. Carbon monoxide methanation activity of the bimetallic catalysts is quite similar to that of the supported platinum catalyst. 6 refs., 6 figs., 2 tabs.

Structure-activity relationships of carbon-supported platinum-bismuth and platinum-antimony oxidation catalysts

CSIR Research Space (South Africa)

Maphoru, MV

2017-04-01

Full Text Available Compositional and morphological studies on supported platinum are important for the improvement and expanded use of catalysts for oxidative coupling reactions. Nanocomposites consisting of 5% Pt supported on activated carbon and promoted with 5% Bi...

Acetylacetone as an efficient electron shuttle for concerted redox conversion of arsenite and nitrate in the opposite direction.

Science.gov (United States)

Chen, Zhihao; Song, Xiaojie; Zhang, Shujuan; Wu, Bingdang; Zhang, Guoyang; Pan, Bingcai

2017-11-01

The redox conversion of arsenite and nitrate has direct effects on their potential environment risks. Due to the similar reduction potentials, there are few technologies that can simultaneously oxidize arsenite and reduce nitrate in one process. Here, we demonstrate that a diketone-mediated photochemical process could efficiently do this. A combined experimental and theoretical investigation was conducted to elucidate the mechanisms behind the redox conversion in the UV/acetylacetone (AA) process. Our key finding is that UV irradiation significantly changed the redox potential of AA. The excited AA, 3 (AA)*, acted as a semiquinone radical-like electron shuttle. For arsenite oxidation, the efficiency of 3 (AA)* was 1-2 orders of magnitude higher than those of quinone-type electron shuttles, whereas the consumption of AA was 2-4 orders of magnitude less than those of benzonquinones. The oxidation of arsenite and reduction of nitrate could be both accelerated when they existed together in UV/AA process. The results indicate that small diketones are some neglected but potent electron shuttles of great application potential in regulating aquatic redox reactions with the combination of UV irradiation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Oxygen-related 1-platinum defects in silicon: An electron paramagnetic resonance study

Science.gov (United States)

Juda, U.; Scheerer, O.; Höhne, M.; Riemann, H.; Schilling, H.-J.; Donecker, J.; Gerhardt, A.

1996-09-01

A monoclinic 1-platinum defect recently detected was investigated more thoroughly by electron paramagnetic resonance (EPR). The defect is one of the dominating defects in platinum doped silicon. With a perfect reproducibility it is observed in samples prepared from n-type silicon as well as from p-type silicon, in float zone (FZ) silicon as well as in Czochralski (Cz) silicon. Its concentration varies with the conditions of preparation and nearly reaches that of isolated substitutional platinum in Cz silicon annealed for 2 h at 540 °C after quenching from the temperature of platinum diffusion. Because of its concentration which in Cz-Si exceeds that in FZ-Si the defect is assumed to be oxygen-related though a hyperfine structure with 17O could not be resolved. The defect causes a level close to the valence band. This is concluded from variations of the Fermi level and from a discussion of the spin Hamiltonian parameters. In photo-EPR experiments the defect is coupled to recently detected acceptorlike self-interstitial related defects (SIRDs); their level position turns out to be near-midgap. These defects belong to the lifetime limiting defects in Pt-doped Si.

Platinum(II) Complexes of 2-(Dimethylamino)ethylselenolate-Donor-Acceptor Inter-Ligand Interactions as Evident from Experimental and TD-DFT Computational Analysis

Czech Academy of Sciences Publication Activity Database

Dey, S.; Jain, V. K.; Knoedler, A.; Kaim, W.; Záliš, Stanislav

č. 11 (2001), s. 2965-2973 ISSN 1434-1948 R&D Projects: GA MŠk ME 439 Institutional research plan: CEZ:AV0Z4040901 Keywords : platinum * selenium * NMR spectroscopy Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.475, year: 2001

Enhanced catalytic activity of nanoscale platinum islands loaded ...

Indian Academy of Sciences (India)

2016-08-26

Aug 26, 2016 ... In the present study, different catalysts (∼ 10 nm thick) including metals, noble metals and metal oxides, were loaded in dotted island form over SnO2 thin film for LPG gas detection. A comparison of various catalysts indicated that the presence of platinum dotted islands over SnO2 thin film deposited by r.f. ...

Platinum(II) complexes as spectroscopic probes for biomolecules

Energy Technology Data Exchange (ETDEWEB)

Ratilla, E.

1990-09-21

The use of platinum(II) complexes as tags and probes for biomolecules is indeed advantageous for their reactivities can be selective for certain purposes through an interplay of mild reaction conditions and of the ligands bound to the platinum. The use of {sup 195}Pt NMR as a method of detecting platinum and its interactions with biomolecules was carried out with the simplest model of platinum(II) tagging to proteins. Variable-temperature {sup 195}Pt NMR spectroscopy proved useful in studying the stereodynamics of complex thioethers like methionine. The complex, Pt(trpy)Cl{sup +}, with its chromophore has a greater potential for probing proteins. It is a noninvasive and selective tag for histidine and cysteine residues on the surface of cytochrome c at pH 5. The protein derivatives obtained are separable, and the tags are easily quantitated and differentiated through the metal-to-ligand charge transfer bands which are sensitive to the environment of the tag. Increasing the pH to 7.0 led to the modification by Pt(trpy)Cl{sup +}of Arg 91 in cytochrome c. Further studies with guanidine-containing ligands as models for arginine modification by Pt(trpy)Cl{sup +} showed that guanidine can act as a terminal ligand and as a bridging ligand. Owing to the potential utility of Pt(trpy)L{sup n+} as electron dense probes of nucleic acid structure, interactions of this bis-Pt(trpy){sup 2+} complex with nucleic acids was evaluated. Indeed, the complex interacts non-covalently with nucleic acids. Its interactions with DNA are not exactly the same as those of its precedents. Most striking is its ability to form highly immobile bands of DNA upon gel electrophoresis. 232 refs.

Spatio-temporal dynamics of oscillatory heterogeneous catalysis: CO oxidation on platinum

Science.gov (United States)

Yamamoto, S. Y.; Surko, C. M.; Maple, M. B.; Pina, R. K.

1995-06-01

Reaction-rate oscillations in the oxidation of carbon monoxide on the surface of platinum catalysts are studied in a continuous flow reactor at atmospheric pressure using infrared imaging. Small-amplitude temperature oscillations (0.2-8 K) result in approximately isothermal conditions, where changes in rate constants, for typical activation energies and temperatures, are small. The catalysts are in the form of platinum thin films on quartz substrates and provide highly repeatable oscillatory behavior. The platinum films are fabricated in the form of annular rings which provide a quasi-one-dimensional geometry in order to simplify comparison to theoretical models. Time-series measurements by means of thermocouples are used to characterize the oscillations. The infrared images show that most oscillations are spatially synchronized to within the 0.25 s time resolution of the experiment. The images also show that ``fine structure'' oscillations (i.e., small-amplitude, high frequency oscillations superimposed on larger-amplitude waveforms) are associated with spatially desynchronized patterns.

Textured strontium titanate layers on platinum by atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Blomberg, T., E-mail: tom.blomberg@asm.com [ASM Microchemistry Ltd., Vaeinoe Auerin katu 12 A, 00560 Helsinki (Finland); Anttila, J.; Haukka, S.; Tuominen, M. [ASM Microchemistry Ltd., Vaeinoe Auerin katu 12 A, 00560 Helsinki (Finland); Lukosius, M.; Wenger, Ch. [IHP, Im Technologiepark 25, 15236 Frankfurt (Oder) (Germany); Saukkonen, T. [Aalto University, Puumiehenkuja 3, 02150 Espoo (Finland)

2012-08-31

Formation of textured strontium titanate (STO) layers with large lateral grain size (0.2-1 {mu}m) and low X-ray reflectivity roughness ({approx} 1.36 nm) on Pt electrodes by industry proven atomic layer deposition (ALD) method is demonstrated. Sr(t-Bu{sub 3}Cp){sub 2}, Ti(OMe){sub 4} and O{sub 3} precursors at 250 Degree-Sign C were used to deposit Sr rich STO on Pt/Ti/SiO{sub 2}/Si Empty-Set 200 mm substrates. After crystallization post deposition annealing at 600 Degree-Sign C in air, most of the STO grains showed a preferential orientation of the {l_brace}001{r_brace} plane parallel to the substrate surface, although other orientations were also present. Cross sectional and plan view transmission electron microscopy and electron diffraction analysis revealed more than an order of magnitude larger lateral grain sizes for the STO compared to the underlying multicrystalline {l_brace}111{r_brace} oriented platinum electrode. The combination of platinum bottom electrodes with ALD STO(O{sub 3}) shows a promising path towards the formation of single oriented STO film. - Highlights: Black-Right-Pointing-Pointer Amorphous strontium titanate (STO) on platinum formed a textured film after annealing. Black-Right-Pointing-Pointer Single crystal domains in 60 nm STO film were 0.2-1 {mu}m wide. Black-Right-Pointing-Pointer Most STO grains were {l_brace}001{r_brace} oriented.

Bioaccumulation of platinum group metals in dolphins, Stenella sp ...

African Journals Online (AJOL)

Platinum group metals (PGMs) concentrations were measured in the tissues= of dolphins (Stenella sp.) caught along the Ghanaian coastline. Tissues from specimens caught by fishermen from Dixcove, western Ghana, were analysed in 2006 for palladium (Pd), platinum (Pt) and rhodium (Rh) using the Neutron Activation ...

Determination of Chromium(III), Chromium(VI), and Chromium(III) acetylacetonate in water by ion-exchange disk extraction/metal furnace atomic absorption spectrometry

International Nuclear Information System (INIS)

Kamakura, Nao; Inui, Tetsuo; Kitano, Masaru; Nakamura, Toshihiro

2014-01-01

A new method for the separate determination of Chromium(III) (Cr(III)), Chromium(VI) (Cr(VI)), and Cr(III) acetylacetonate (Cr(acac) 3 ) in water was developed using a cation-exchange extraction disk (CED) and an anion-exchange extraction disk (AED) combined with metal furnace atomic absorption spectrometry (MFAAS). A 100-mL water sample was adjusted to pH 5.6 and passed through the CED placed on the AED. Cr(acac) 3 and Cr(III) were adsorbed on the CED, and Cr(VI) was adsorbed on the AED. The adsorbed Cr(acac) 3 was eluted with 50 mL of carbon tetrachloride, followed by the elution of Cr(III) with 50 mL of 3 mol L −1 nitric acid. Cr(VI) was eluted with 50 mL of 3 mol L −1 nitric acid. The chemical species of Cr eluted from the CED with carbon tetrachloride was identified as Cr(acac) 3 using infrared spectroscopy. The eluate of Cr(acac) 3 was diluted to 100 mL with carbon tetrachloride, and those of Cr(III) and Cr(VI) were diluted to 100 mL with deionized water. All of the solutions were subsequently analyzed by MFAAS. The calibration curve for the Cr(acac) 3 aqueous solutions exhibited good linearity in the range of 0.1 to 1 ng. The detection limit of Cr, which corresponded to three times the standard deviation (n = 10) of the blank values, was 20 pg. The recovery test for Cr(III), Cr(VI), and Cr(acac) 3 exhibited desirable results (96.0%–107%) when 5 μg of each species (50 μg L −1 ) was added to 100 mL water samples (i.e., tap water, rainwater, and bottled drinking water). In a humic acid solution, Cr(acac) 3 was quantitatively recovered (103%), but Cr(III) and Cr(VI) exhibited poor recoveries (i.e., 84.8% and 78.4%, respectively). - Highlights: • A determination method of Cr(III), Cr(VI), and Cr(III) acetylacetonate in water was developed. • The combination of ion-exchange resin disks with metal furnace AAS was used. • No effect of humic acid on the recovery of Cr(III) acetylacetonate was observed. • The proposed method enabled the determination

A Gene Expression Profile of BRCAness That Predicts for Responsiveness to Platinum and PARP Inhibitors

Science.gov (United States)

2017-02-01

affecting the function of Fanconi Anemia (FA) genes ( FANCA /B/C/D2/E/F/G/I/J/L/M, PALB2) or DNA damage response genes involved in HR 5 (ATM, ATR...Award Number: W81XWH-10-1-0585 TITLE: A Gene Expression Profile of BRCAness That Predicts for Responsiveness to Platinum and PARP Inhibitors...To) 15 July 2010 – 2 Nov.2016 4. TITLE AND SUBTITLE A Gene Expression Profile of BRCAness That Predicts for Responsiveness to Platinum and PARP

Biological Recovery of Platinum Complexes from Diluted Aqueous Streams by Axenic Cultures.

Directory of Open Access Journals (Sweden)

Synthia Maes

Full Text Available The widespread use of platinum in high-tech and catalytic applications has led to the production of diverse Pt loaded wastewaters. Effective recovery strategies are needed for the treatment of low concentrated waste streams to prevent pollution and to stimulate recovery of this precious resource. The biological recovery of five common environmental Pt-complexes was studied under acidic conditions; the chloro-complexes PtCl42- and PtCl62-, the amine-complex Pt(NH34Cl2 and the pharmaceutical complexes cisplatin and carboplatin. Five bacterial species were screened on their platinum recovery potential; the Gram-negative species Shewanella oneidensis MR-1, Cupriavidus metallidurans CH34, Geobacter metallireducens, and Pseudomonas stutzeri, and the Gram-positive species Bacillus toyonensis. Overall, PtCl42- and PtCl62- were completely recovered by all bacterial species while only S. oneidensis and C. metallidurans were able to recover cisplatin quantitatively (99%, all in the presence of H2 as electron donor at pH 2. Carboplatin was only partly recovered (max. 25% at pH 7, whereas no recovery was observed in the case of the Pt-tetraamine complex. Transmission electron microscopy (TEM revealed the presence of both intra- and extracellular platinum particles. Flow cytometry based microbial viability assessment demonstrated the decrease in number of intact bacterial cells during platinum reduction and indicated C. metallidurans to be the most resistant species. This study showed the effective and complete biological recovery of three common Pt-complexes, and estimated the fate and transport of the Pt-complexes in wastewater treatment plants and the natural environment.

Differential transport of platinum compounds by the human organic cation transporter hOCT2 (hSLC22A2)

NARCIS (Netherlands)

H. Burger (Herman); A. Zoumaro-Djayoon (Adja); A.W.M. Boersma (Anton); J. Helleman (Jozien); P.M.J.J. Berns (Els); A.H.J. Mathijssen (Ron); W.J. Loos (Walter); E.A.C. Wiemer (Erik)

2010-01-01

textabstractAbstract BACKGROUND: Solute carriers (SLCs), in particular organic cation transporters (OCTs), have been implicated in the cellular uptake of platinum-containing anticancer compounds. The activity of these carriers may determine the pharmacokinetics and the severity of side effects,

Association of well-characterized lung cancer lncRNA polymorphisms with lung cancer susceptibility and platinum-based chemotherapy response.

Science.gov (United States)

Gong, Wei-Jing; Yin, Ji-Ye; Li, Xiang-Ping; Fang, Chao; Xiao, Di; Zhang, Wei; Zhou, Hong-Hao; Li, Xi; Liu, Zhao-Qian

2016-06-01

Long non-coding RNAs (lncRNAs) play important roles in carcinogenesis and drug efficacy. Platinum-based chemotherapy is first-line treatment for lung cancer chemotherapy. In this study, we aimed to investigate the association of well-characterized lung cancer lncRNA genetic polymorphisms with the lung cancer susceptibility and platinum-based chemotherapy response. A total of 498 lung cancer patients and 213 healthy controls were recruited in the study. Among them, 467 patients received at least two cycles of platinum-based chemotherapy. Thirteen polymorphisms in HOXA distal transcript antisense RNA (HOTTIP), HOX transcript antisense intergenic RNA (HOTAIR), H19, CDKN2B antisense RNA 1 (ANRIL), colon cancer-associated transcript 2 (CCAT2), metastasis-associated lung adenocarcinoma transcript 1 (MALAT1), and maternally expressed gene 3 (MEG3) genes were genotyped by allele-specific MALDI-TOF mass spectrometry. We found that patients with HOTTIP rs5883064 C allele or rs1859168 A allele had increased lung cancer risk (P = 0.01, P = 0.01, respectively). CCAT2 rs6983267 (P = 0.02, adenocarcinoma) and H19 rs2107425 (P = 0.02, age under 50 years) showed strong relationship with lung cancer susceptibility. CCAT2 rs6983267, H19 rs2839698, MALAT1 rs619586, and HOTAIR rs7958904 were associated with platinum-based chemotherapy response in dominant model ((P = 0.02, P = 0.04, P = 0.04, P = 0.01, respectively). ANRIL rs10120688 (P = 0.02, adenocarcinoma) and rs1333049 (P = 0.04, small-cell lung cancer), H19 rs2107425 (P = 0.02, small-cell lung cancer) and HOTAIR rs1899663 (P = 0.03, male; P = 0.03, smoker) were associated with response to platinum-based chemotherapy. HOTTIP, CCAT2, H19, HOTAIR, MALATI, ANRIL genetic polymorphisms were significantly associated with lung cancer susceptibility or platinum-based chemotherapy response. They may be potential clinical biomarkers to predict lung cancer risk and platinum

Recycling of platinum group metals from the automotive catalysts

International Nuclear Information System (INIS)

Benevit, Mariana; Petter, Patricia Melo Halmenschlager; Veit, Hugo Marcelo

2014-01-01

Currently it is very important to use alternative sources of raw material for obtaining metals, avoiding the traditional mining. This work aims to characterize and evaluate the recoverability of platinum group metals present in automotive catalysts. Thus, the catalysts were divided into two groups: the first was catalysts used in 1.0 cars and the second was catalyst used in 2.0 cars. DRX and FRX techniques and chemical analysis performed by ICP/OES was used to characterized these materials. The results showed that there is a significant amount of platinum group elements in catalyst waste, which can be separated and reused. In the next step, hydro and pyrometallurgical routes, for metals extraction from catalyst waste, will be studied. (author)

Niraparib Maintenance Therapy in Platinum-Sensitive, Recurrent Ovarian Cancer

NARCIS (Netherlands)

Mirza, M. R.; Monk, B. J.; Herrstedt, J.; Oza, A. M.; Mahner, S.; Redondo, A.; Fabbro, M.; Ledermann, J. A.; Lorusso, D.; Vergote, I.; Ben-Baruch, N. E.; Marth, C.; Madry, R.; Christensen, R. D.; Berek, J. S.; Dorum, A.; Tinker, A. V.; du Bois, A.; Gonzalez-Martin, A.; Follana, P.; Benigno, B.; Rosenberg, P.; Gilbert, L.; Rimel, B. J.; Buscema, J.; Balser, J. P.; Agarwal, S.; Matulonis, U. A.; van der Zee, A.G.J.

2016-01-01

BACKGROUND Niraparib is an oral poly(adenosine diphosphate [ADP]-ribose) polymerase (PARP) 1/2 inhibitor that has shown clinical activity in patients with ovarian cancer. We sought to evaluate the efficacy of niraparib versus placebo as maintenance treatment for patients with platinum-sensitive,

The Effect of Precursor Ligands and Oxidation State in the Synthesis of Bimetallic Nano-Alloys

KAUST Repository

LaGrow, Alec P.; Knudsen, Kristian; AlYami, Noktan; Anjum, Dalaver H.; Bakr, Osman

2015-01-01

- pair. The two nanocrystal precursors can be uti-lized independently and can control the size with a trend of Pt(acac)222222 for the secondary metal (copper or nickel). These results open up avenues to understand

Determination of platinum and gold in biological materials by neutron activation analysis

International Nuclear Information System (INIS)

Taskaev, E.; Grigorov, T.

1988-01-01

A procedure for platinum and gold determination utilizing neutron activation combined with radiochemical separation was developed. The reaction 198 Pt (n, γ) 199 Pt undergoing β decay into 199 Au is used for Pt determination. Four procedures for gold separation are examined: adsorption on untreated polyurethane foam (UPF), extraction with dibutyl sulphide, reduction of gold to elementary state in conc. H 2 SO 4 , and extraction of gold as diethyl-dithiocarbamate complex. The extraction with Cu(DDC) 2 is chosen as the most suitable process and applied to platinum and gold determinations in Bowen's Kale and mice organs, previously treated with Biocisplatinum specimens. (author) 12 refs.; 5 figs

Recent strikes in South Africa’s platinum-group metal mines: effects upon world platinum-group metal supplies

Science.gov (United States)

Yager, Thomas R.; Soto-Viruet, Yadira; Barry, James J.

2012-01-01

The recent labor disputes over wages and working conditions that have affected South Africa’s three leading platinum-group metal (PGM) producers have affected an industry already plagued by market pressures and labor unrest and raised the specter of constraints in the world’s supply of these metals. Although low demand for these metals in 2011 and 2012 helped to offset production losses of recent years, and particularly those losses caused by the strikes in 2012, a prolonged resumption of strikes could cause severe shortages of iridium, platinum, rhodium, ruthenium, and, to a lesser extent, palladium.

Investigation of a combined platinum and electron lifetime control treatment for silicon

International Nuclear Information System (INIS)

Jia, Yunpeng; Cui, Zhihang; Yang, Fei; Zhao, Bao; Zou, Shikai; Liang, Yongsheng

2017-01-01

In silicon, the effect of Combined Lifetime Treatment (CLT) involving platinum diffusion and subsequent electron irradiation is different from the separate treatments of platinum diffusion and electron irradiation, even the treatment of electron irradiation followed by platinum diffusion. In this paper, we investigated the experimental behavior of different kinds of lifetime treated samples. We found that the reverse leakage current (I rr ) increases with the increasing platinum diffusion temperature or electron irradiation dose in the separate treatments. Conversely, I rr of the CLT samples decreased with rising platinum diffusion temperature at the same dose of subsequent electron irradiation. By deep-level transient spectroscopy (DLTS), a new energy level E7 (Ec −0.376 eV) was found in our CLT samples. The new level E7 suppresses the dominance of the deeper level E8 (Ec −0.476 eV), which is caused by electron irradiation directly and results in I rr ’s increase. The formation of the level E7 comes from the complex defect-combined effect between platinum atoms and silicon vacancies, and it affects device’s characteristics finally. These research will be helpful to the development of platinum-diffused devices used in intense electron irradiation environments.

Investigation of a combined platinum and electron lifetime control treatment for silicon

Energy Technology Data Exchange (ETDEWEB)

Jia, Yunpeng [College of Electronic Information and Control Engineering, Beijing University of Technology, Beijing 100124 (China); Cui, Zhihang, E-mail: czhczh321321@126.com [College of Electronic Information and Control Engineering, Beijing University of Technology, Beijing 100124 (China); Yang, Fei [State Grid Smart Electrical Engineering, Beijing 100192 (China); Zhao, Bao; Zou, Shikai; Liang, Yongsheng [College of Electronic Information and Control Engineering, Beijing University of Technology, Beijing 100124 (China)

2017-02-01

In silicon, the effect of Combined Lifetime Treatment (CLT) involving platinum diffusion and subsequent electron irradiation is different from the separate treatments of platinum diffusion and electron irradiation, even the treatment of electron irradiation followed by platinum diffusion. In this paper, we investigated the experimental behavior of different kinds of lifetime treated samples. We found that the reverse leakage current (I{sub rr}) increases with the increasing platinum diffusion temperature or electron irradiation dose in the separate treatments. Conversely, I{sub rr} of the CLT samples decreased with rising platinum diffusion temperature at the same dose of subsequent electron irradiation. By deep-level transient spectroscopy (DLTS), a new energy level E7 (Ec −0.376 eV) was found in our CLT samples. The new level E7 suppresses the dominance of the deeper level E8 (Ec −0.476 eV), which is caused by electron irradiation directly and results in I{sub rr}’s increase. The formation of the level E7 comes from the complex defect-combined effect between platinum atoms and silicon vacancies, and it affects device’s characteristics finally. These research will be helpful to the development of platinum-diffused devices used in intense electron irradiation environments.

Preliminary study of platinum accumulation in the fruitbodies of a model fungal species: king oyster mushroom (Pleurotus eryngii)

International Nuclear Information System (INIS)

Urban, P.L.; Bazala, M.A.; Bystrzejewska-Piotrowska, G.; Pianka, D.; Steborowski, R.; Asztemborska, M.; Kowalska, J.; Manjon, J.L.; Kuthan, R.T.

2005-01-01

A model species of saprophytic fungus, king oyster mushroom (Pleurotus eryngii), was cultivated on barley substrate supplied with [Pt(NH 3 ) 4 ](NO 3 ) 2 , under well defined conditions. The samples of the collected fruiting bodies were digested and analyzed for total platinum content by means of ICP-MS. The results proved that platinum is not accumulated in the fruitbodies of Pleurotus eryngii for a wide range of Pt concentrations in the culture substrate (100-1000 ppb Pt in 50 ml of water solution added to ca. 450 g of hydrated barley seeds per container). Observable levels of Pt were only found in the fruitbodies obtained from the medium contaminated with 10000 ppb (10 ppm) platinum solution. This demonstrates significant difference in the effectiveness of platinum extraction in fungi and plants, which are capable to accumulate platinum even when supplied at lower concentration (<500 ppb). It also shows different physiological pathways of platinum and other elements which are easily accumulated in the fruitbodies of the same species. (author)

Platinum-Resistor Differential Temperature Sensor

Science.gov (United States)

Kolbly, R. B.; Britcliffe, M. J.

1985-01-01

Platinum resistance elements used in bridge circuit for measuring temperature difference between two flowing liquids. Temperature errors with circuit are less than 0.01 degrees C over range of 100 degrees C.

Enzymatic recovery of platinum (IV) from industrial wastewater using ...

African Journals Online (AJOL)

highest hydrogen-dependent platinum (IV) reducing activity in the presence of hydrogenase and its physiological electron carrier, cytochrome c3. When the purified hydrogenase enzyme (with and without cytochrome c3) was used with the industrial effluent, containing 7.9 mg.l-1 platinum, only 10 – 15% recovery was noted ...

Platinum redispersion on metal oxides in low temperature fuel cells

DEFF Research Database (Denmark)

Tripkovic, Vladimir; Cerri, Isotta; Nagami, Tetsuo

2013-01-01

We have analyzed the aptitude of several metal oxide supports (TiO2, SnO2, NbO2, ZrO2, SiO2, Ta2O5 and Nb2O5) to redisperse platinum under electrochemical conditions pertinent to the Proton Exchange Membrane Fuel Cell (PEMFC) cathode. The redispersion on oxide supports in air has been studied in ...

A retrospective evaluation of activity of gemcitabine/platinum regimens in the treatment of recurrent ovarian cancer

Directory of Open Access Journals (Sweden)

Tran N. Le

2017-11-01

Full Text Available Abstract Background While many of these agents have been compared in prospective clinical trials, the gemcitabine/platinumbased regimens have not been compared in a prospective, randomized clinical trial. While bothgemcitabine/carboplatin and gemcitabine/cisplatin have a similar ORR in separate clinical trials, the tworegimens have never been directly been compared. With overlapping dose-limiting toxicity of thrombocytopenia, the gemcitabine/carboplatin regimen has been challenging to employ in the clinical setting in previously treated ovarian cancer patients and is often associated with treatment delays and/or dose reductions. Gemcitabine/cisplatin can also be a challenge due to its dose limiting neuropathy and renal toxicity, especially in previously treated patients. In the absence of any prospective, head to head comparison this retrospective study was embarked upon to compare the response rate and toxicity profiles of gemcitabine/cisplatin verses gemcitabine/carboplatin for the treatment of platinum-sensitive verses platinum-resistant recurrent ovarian cancer. Methods This was a retrospective chart review study that identified patients that had received either gemcitabine/cisplatin or gemcitabine/carboplatin for treatment of recurrent ovarian cancer and compared documented hematological and non-hematological toxicity and response based on RECIST (v1.1. Data was evaluated based upon platinum sensitivity/resistance as well. Results A total of 93 patients were identified that had received a gemcitabine/platinum regimen with 48 with recurrent ovarian cancer that were included in the study. There were 21 patients in the gemcitabine/cisplatin arm and 27 patients identified in the gemcitabine/carboplatin arm. Objective response rate (ORR was greater in platinum-sensitive patients that received gemcitabine/carboplatin compared to gemcitabine/cisplatin (8 (67% vs 2 (25%, p < 0.05. Conversely, ORR was greater in platinum-resistant patients treated

Platinum bioaccumulation by mustard plants (Sinapis alba L.)

International Nuclear Information System (INIS)

Hawienczyk, M.; Bystrzejewska-Piotrowska, G.; Kowalska, J.; Asztemborska, M.

2005-01-01

The ability of hydroponically cultivated Indian mustard plants (Sinapis alba L.) to accumulate platinum was investigated. The Pt-bioaccumulation in leaves, stem and shoots of plants growing for 2 and 4 weeks at Pt-concentration of 50 and 500 μg/L was compared. The relation between dry and fresh weight was also estimated. Adsorptive stripping voltammetry (AdSV) and mass spectrometry with inductively coupled plasma (ICP-MS) were applied for determination of Pt. Increasing Pt-concentration from 50 to 500 μg/L in the medium causes: (1) reduction of the root tissue hydration level at unchanged modification in aboveground parts of the plants and (2) decrease of the Pt transfer factor (TF) for roots and increase for leaves and stem. Duration of the culture influenced on Pt-accumulation in roots and in aboveground organs of mustard plants. Transfer factor for Pt between 560 and 1600 makes Indian mustard plants one at Pt-hyperaccumulators. Distribution of Pt-bioaccumulation in the plant organs may be useful for biomonitoring of platinum in the environment. (author)

Platinum(0-1,3-divinyl-1,1,3,3-tetramethyldisiloxane Complex as a Pt Source for Pt/SnO2 Catalyst

Directory of Open Access Journals (Sweden)

Agnieszka Martyla

2014-01-01

Full Text Available This paper presents new preparation method of Pt/SnO2, an important catalytic system. Besides of its application as a heterogenic industrial catalyst, it is also used as a catalyst in electrochemical processes, especially in fuel cells. Platinum is commonly used as an anode catalyst in low temperature fuel cells, fuelled with alcohols of low molecular weight such as methanol. Platinum(0-1,3-divinyl-1,1,3,3-tetramethyldisiloxane complex was used as a precursor of metallic phase. The aim of the research was to obtain a highly active in electrochemical system Pt/SnO2 catalyst with low metal load. Considering small size of Pt crystallites, it should result in high activity of Pt/SnO2 system. The presented method of SnO2 synthesis allows for obtaining support consisting of nanoparticles. The effect of the thermal treatment on activity of Pt/SnO2 gel was demonstrated. The system properties were investigated using TEM, FTIR (ATR, and XRD techniques to describe its thermal structural evolution. The results showed two electrocatalytical activity peaks for drying at a temperature of 430 K and above 650 K.

Molecular structure, spectroscopic studies, and coppersbnd oxygen bond strength of α-methyl and α-ethyl derivatives of copper (II) acetylacetonate; Experimental and theoretical approach

Science.gov (United States)

Seyedkatouli, Seyedabdollah; Vakili, Mohammad; Tayyari, Sayyed Faramarz; Afzali, Raheleh

2018-05-01

This paper presents a combined experimental and theoretical study on the Cusbnd O bond strength of copper (II) α-methylacetylacetonate, Cu(3-Meacac)2, and copper (II) α-ethylacetylacetonate, Cu(3-Etacac)2, complexes in comparison to that in copper (II) acetylacetonate, Cu(acac)2. For this purpose, the molecular structure, UV spectra, and complete vibrational assignment of target molecules were investigated by DFT, Natural Bond Orbital (NBO) theory, and Atoms-in-Molecules (AIM) analysis at the B3LYP/6-311G* level of theory. The mentioned results are compared with those in Cu(acac)2. Fourier transform-Raman, IR, and UV spectra of these complexes have been also recorded. A complete assignment of the observed band frequencies has been done. All theoretical and experimental spectroscopic results are consisting with a stronger metal-oxygen bond in Cu(3-Meacac)2 and Cu(3-Etacac)2 complexes compared with Cu(acac)2. In addition, these results confirm that there is no significant difference between the Cusbnd O bond strength of the Cu(3-Meacac)2 and Cu(3-Etacac)2 complexes.

Structural property of platinum mononitride

International Nuclear Information System (INIS)

Yu, L.H.; Yao, K.L.; Liu, Z.L.; Zhang, Y.S.

2007-01-01

The structural stability and pressure-induced structural phase transition of platinum mononitride (PtN), as well as its electronic structure, were studied using the full potential augmented plane wave plus local orbitals method with the generalized gradient approximation (GGA) exchange-correlation functional. The total energy calculations show that the optimized wurtzite structure is most stable energetically among four structures: zinc blende, rocksalt, CsCl and wurtzite, which reveals the platinum mononitride PtN perhaps crystallizes in the wurtzite structure; the pressure of phase transition from wurtzite to rocksalt is predicted to be 41.4 GPa.The calculated bulk modulus of the wurtzite structure is 99.41 GPa, which is smaller than that of the other three structures and face-centered cubic Pt. The band structure calculations show wurtzite PtN is metallic

High platinum utilization in ultra-low Pt loaded PEM fuel cell cathodes prepared by electrospraying

Energy Technology Data Exchange (ETDEWEB)

Martin, S.; Garcia-Ybarra, P.L.; Castillo, J.L. [Dept. Fisica Matematica y de Fluidos, Facultad de Ciencias, UNED, Senda del Rey 9, 28040 Madrid (Spain)

2010-10-15

Cathode electrodes for proton exchange membrane fuel cells (PEMFCs) with ultra-low platinum loadings as low as 0.012 mg{sub Pt}cm{sup -2} have been prepared by the electrospray method. The electrosprayed layers have nanostructured fractal morphologies with dendrites formed by clusters (about 100 nm diameter) of a few single catalyst particles rendering a large exposure surface of the catalyst. Optimization of the control parameters affecting this morphology has allowed us to overcome the state of the art for efficient electrodes prepared by electrospraying. Thus, using these cathodes in membrane electrode assemblies (MEAs), a high platinum utilization in the range 8-10 kW g{sup -1} was obtained for the fuel cell operating at 40 C and atmospheric pressure. Moreover, a platinum utilization of 20 kW g{sup -1} was attained under more suitable operating conditions (70 C and 3.4 bar over-pressure). These results substantially improve the performances achieved previously with other low platinum loading electrodes prepared by electrospraying. (author)

Platinum/ceria/alumina catalysts on microstructures for carbon monoxide conversion

Energy Technology Data Exchange (ETDEWEB)

Germani, G.; Schuurman, Y.; Mirodatos, C. [Institut de Recherches sur la Catalyse, CNRS, 2 Avenue Albert Einstein, 69626 Villeurbanne (France); Alphonse, P.; Courty, M. [CIRIMAT, UMR-CNRS 5085, Universite Paul Sabatier, 118 route de Narbonne, 31062 Toulouse Cedex 04 (France)

2005-12-15

Platinum/ceria/alumina catalysts have been prepared by a sol-gel method and coated in the microchannels of stainless steel platelets. These catalysts are very active for the water-gas shift reaction between 300 and 400{sup o}C. Moreover, they are non-pyrophoric and thus well suited for the purification of hydrogen for PEM fuel cells. The obtained coatings show good adherence and catalytic activity. The influence of the amount of platinum and ceria as well as the effect of a binder on the catalytic performance has been investigated. The samples have been characterized before reaction by XRD, SEM and by N{sub 2} adsorption measurements. The kinetics, free from internal diffusion limitations, over these thin films have been described by a power law rate equation. An activation energy of 86kJ/mol has been found and at 260{sup o}C the TOF corresponds to 0.6+/-0.1s{sup -1} for all investigated samples. The superior activity of the platelets compared to the powder samples is attributed to the diffusion limitations inside the powder pellets. Thus catalysts deposited on microstructured platelets lead to a better platinum utilization.

Tripodal osmium polypyridyl complexes for self-assembly on platinum nanoparticles

NARCIS (Netherlands)

Contreras-Carballada, P.; Edafe, F.; Tichelaar, F.D.; Belser, P.; De Cola, L.; Williams, R.M.

2011-01-01

The combination of platinum nanoparticles with a tripodal osmium complex that anchors to the metal surface leads, under visible light irradiation, to the formation of solvated electrons. The formation kinetics is limited by the detachment of the electron from the platinum surface into the solution,

Dissolved Platinum Concentrations in Coastal Seawater: Boso to Sanriku Areas, Japan.

Science.gov (United States)

Mashio, Asami Suzuki; Obata, Hajime; Gamo, Toshitaka

2017-08-01

Platinum, one of the rarest elements in the earth's crust, is now widely used in a range of products, such as catalytic converters in automobiles and anticancer drugs. Increasing use and dispersal of platinum has the potential to affect aquatic environments. Platinum concentrations in open ocean seawater have been found to be very low (approximately 0.2 pmol/L); however, Pt distributions and biogeochemical cycles in coastal areas are unknown. In this study, we investigated Pt concentrations in coastal waters between the Boso and Sanriku areas, Japan, after the 2011 tsunami. We determined sub-picomolar levels of dissolved Pt using isotope-dilution Inductively coupled plasma mass spectrometry after column preconcentration with an anion exchange resin. Dissolved Pt concentrations were found to be in the range 0.20-1.5 pmol/L, with the highest concentration in bottom water of the Boso coastal area, and at stations close to Tokyo Bay. Assuming thermodynamical equilibrium, Pt was determined to be present in the form PtCl 5 (OH) 2- , even in low-oxygen coastal waters. Vertical profiles indicated Pt levels increased toward seafloors near coastal stations and were similar to those of the open ocean at trench stations. High concentrations of dissolved Pt are thought to be derived from coastal sediments.

Concentration and measuring Platinum Group Elements (PGE) Transfer Factor in soil and vegetations

International Nuclear Information System (INIS)

Adibah Sakinah Oyub

2012-01-01

This study was conducted to determine the concentration and to measure platinum group elements (PGE) transfer factor in environmental samples of roadside soil and vegetation. The use of vehicle catalytic converter has released platinum group elements (PGE) and other gases into the environment. Thus, roadside soil and plants were exposed to this element and has become the medium for the movement of this elements. Samples of roadside soil and vegetation were taken at various locations in UKM Bangi Toll and the concentration of platinum group elements (PGE) is determined using mass spectrometry-inductively coupled plasma (ICP-MS). Overall, the concentrations of platinum group elements (PGE), which is the element platinum (Pt) in soil was 0.016 ± 0.036 μgg -1 . While the concentration of the elements palladium (Pd) was 0.079 ± 0.019 μgg -1 and element rhodium (Rh) is at a concentration of 0.013 ± 0.020 μgg -1 . Overall, the transfer factor for the element platinum (Pt) is 1. While the transfer factor of the element palladium (Pd) is 0.96 and the element rhodium (Rh) is 1.11. In conclusion, the concentration of platinum group elements (PGE) in soils have increased. (author)

LDRD final report on synthesis of shape-and size-controlled platinum and platinum alloy nanostructures on carbon with improved durability.

Energy Technology Data Exchange (ETDEWEB)

Shelnutt, John Allen; Garcia, Robert M.; Song, Yujiang; Moreno, Andres M.; Stanis, Ronald J.

2008-10-01

This project is aimed to gain added durability by supporting ripening-resistant dendritic platinum and/or platinum-based alloy nanostructures on carbon. We have developed a new synthetic approach suitable for directly supporting dendritic nanostructures on VXC-72 carbon black (CB), single-walled carbon nanotubes (SWCNTs), and multi-walled carbon nanotubes (MWCNTs). The key of the synthesis is to creating a unique supporting/confining reaction environment by incorporating carbon within lipid bilayer relying on a hydrophobic-hydrophobic interaction. In order to realize size uniformity control over the supported dendritic nanostructures, a fast photocatalytic seeding method based on tin(IV) porphyrins (SnP) developed at Sandia was applied to the synthesis by using SnP-containing liposomes under tungsten light irradiation. For concept approval, one created dendritic platinum nanostructure supported on CB was fabricated into membrane electrode assemblies (MEAs) for durability examination via potential cycling. It appears that carbon supporting is essentially beneficial to an enhanced durability according to our preliminary results.

Platinum-Bismuth Bimetallic Catalysts: Synthesis, Characterization and Applications

OpenAIRE

Saucedo, Jose A, Jr; Xiao, Yang; Varma, Arvind

2015-01-01

Bimetallic catalysts have been explored and shown to exhibit unique characteristics which are not present in monometallic catalysts. Platinum is well known as an effective catalyst for oxidation and reduction reactions, and it can be made more effective when bismuth is introduced as a promotor. Thus, the effectiveness of the Pt-Bi catalyst was demonstrated in prior work. What is not clear, however, is the mechanism behind the catalyst function; why addition of bismuth to platinum decreases de...

Cytotoxic evaluation upon cis-platinum aminodiacetic acid complexes

International Nuclear Information System (INIS)

Almah binti Awaluddin; Parsons, Peter G.; Lean, Jenny M.; Jacobs, Jeffrey J.

1990-01-01

Cytoxic study of cis-platinum aminodiacetic acid complexes. Three novel platinum complexes have been synthesised and characterised by Awaluddin et. al (1987). This introduces a new area of radiopharmaceuticals based on technician and platinum. Cytotoxic studies were conducted on these complexes using four different types of cell lines. The para amina was found to be highly active against multi-resistant ovarian tumor cells compared to normal cells (fibroblast) and other tumor cells. The chemical structure of para-amina appears to be devoid of any functional group resembling current antitumor drugs except for a distant similarity to metotrexate with respect to the p-aminobenzoic type structure. However cell lines such as Hela and MM 253c-1, which is sensitive to metotrexate, were not sensitive to the para amina. Preliminary studies have shown that cells are blocked in the G phase of the cell cycle, suggesting an antimetabolite effect

bis-Nitrile and bis-Dialkylcyanamide Platinum(II) Complexes as Efficient Catalysts for Hydrosilylation Cross-Linking of Siloxane Polymers.

Science.gov (United States)

Islamova, Regina M; Dobrynin, Mikhail V; Ivanov, Daniil M; Vlasov, Andrey V; Kaganova, Elena V; Grigoryan, Galina V; Kukushkin, Vadim Yu

2016-03-05

cis- and trans-Isomers of the platinum(II) nitrile complexes [PtCl2(NCR)2] (R = NMe2, N(C₅H10), Ph, CH2Ph) were examined as catalysts for hydrosilylation cross-linking of vinyl-terminated polydimethylsiloxane and trimethylsilyl-terminated poly(dimethylsiloxane-co-ethylhydrosiloxane) producing high quality silicone rubbers. Among the tested platinum species the cis-complexes are much more active catalysts than their trans-congeners and for all studied platinum complexes cis-[PtCl2(NCCH2Ph)2] exhibits the best catalytic activity (room temperature, c = 1.0 × 10(-4) mol/L, τpot-life 60 min, τcuring 6 h). Although cis-[PtCl₂(NCCH2Ph)2] is less active than the widely used Karstedt's catalyst, its application for the cross-linking can be performed not only at room temperature (c = 1.0 × 10(-4) mol/L), but also, more efficiently, at 80 °C (c = 1.0 × 10(-4)-1.0 × 10(-5) mol/L) and it prevents adherence of the formed silicone rubbers to equipment. The usage of the cis- and trans-[PtCl2(NCR)2] complexes as the hydrosilylation catalysts do not require any inhibitors and, moreover, the complexes and their mixtures with vinyl- and trimethylsilyl terminated polysiloxanes are shelf-stable in air. Tested catalysts do not form colloid platinum particles after the cross-linking.

On synergism in inhibition of liquidphase oxidation of styrene and tetralin by organic phosphites and transition eleement acetylacetonates

International Nuclear Information System (INIS)

Pobedimskij, D.G.; Nasobullin, Sh.A.; Kadyrova, V.Kh.; Kirpichnikov, P.A.

1976-01-01

Synergism has been observed during inhibiting initiated oxidation of styrene or tetralin by organic phosphites in the presence of complex compounds of some transition metals. The results are given of non-additive intensification of antioxidative activity of triphenylphosphite (TPP) and tri-(4-methyl-6-tert.-- butyl)-phenyl-phosphite (TMBP) in the process of initiated oxidation of styrene or tetralin with addition of acetylacetonates of cobalt and vanadyl. During styrene oxidation, inhibition of the reaction with chelate complex of vanadyl is weakened considerably when phosphite is added into the reaction system. During tetralin oxidation, postcatalytic (or branched) oxidation is observed only for large concentration of vanadyl complex. Addition of TPP to above complex sharply increases the induction period. When the induction period is completed, oxidation of tetralin follows the mechanism of usual, i.e. initiated, reaction

Release of low molecular weight silicones and platinum from silicone breast implants.

Science.gov (United States)

Lykissa, E D; Kala, S V; Hurley, J B; Lebovitz, R M

1997-12-01

We have conducted a series of studies addressing the chemical composition of silicone gels from breast implants as well as the diffusion of low molecular weight silicones (LM-silicones) and heavy metals from intact implants into various surrounding media, namely, lipid-rich medium (soy oil), aqueous tissue culture medium (modified Dulbecco's medium, DMEM), or an emulsion consisting of DMEM plus 10% soy oil. LM-silicones in both implants and surrounding media were detected and quantitated using gas chromatography (GC) coupled with atomic emission (GC-AED) as well as mass spectrometric (GC/MS) detectors, which can detect silicones in the nanogram range. Platinum, a catalyst used in the preparation of silicone gels, was detected and quantitated using inductive argon-coupled plasma/mass spectrometry (ICP-MS), which can detect platinum in the parts per trillion range. Our results indicate that GC-detectable low molecular weight silicones contribute approximately 1-2% to the total gel mass and consist predominantly of cyclic and linear poly-(dimethylsiloxanes) ranging from 3 to 20 siloxane [(CH3)2-Si-O] units (molecular weight 200-1500). Platinum can be detected in implant gels at levels of approximately 700 micrograms/kg by ICP-MS. The major component of implant gels appears to be high molecular weight silicone polymers (HM-silicones) too large to be detected by GC. However, these HM-silicones can be converted almost quantitatively (80% by mass) to LM-silicones by heating implant gels at 150-180 degrees C for several hours. We also studied the rates at which LM-silicones and platinum leak through the intact implant outer shell into the surrounding media under a variety of conditions. Leakage of silicones was greatest when the surrounding medium was lipid-rich, and up to 10 mg/day LM-silicones was observed to diffuse into a lipid-rich medium per 250 g of implant at 37 degrees C. This rate of leakage was maintained over a 7-day experimental period. Similarly, platinum was

Effect of Platinum Group Metal Doping in Magnesium Diboride Wires

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Alexiou, Aikaterini; Namazkar, Shahla

2016-01-01

The effect of some platinum group metals(PGM = Rh, Pd, and Pt) on the microstructure and critical current density of Cu/Nb-sheathed MgB2 wires has been studied using Mg1-x PGMxB2 powders with low doping levels. It was found that Pt and Pd do not enter the MgB2 lattice and have only limited influe...

In situ measurements of Merensky pillar behaviour at Impala Platinum

CSIR Research Space (South Africa)

Watson, BP

2009-12-01

Full Text Available to stabilize the stoping excavations. This paper describes the in situ measurement, of stress within a Merensky pillar from Impala Platinum. These measurements were used to derive a stress-strain curve that includes pre and post failure behaviour. 2D FLAC...

The effect of complexation with platinum in polyfluorene derivatives: A photo- and electro-luminescence study

International Nuclear Information System (INIS)

Assaka, Andressa M.; Hu Bin; Mays, Jimmy; Iamazaki, Eduardo T.; Atvars, Teresa D.Z.; Akcelrud, Leni

2011-01-01

The synthesis and characterization of a polymeric structure containing fluorene units statistically linked to 3-cyclohexyl-thiophene and bipyridine PFOTBipy-poly[(4-hexylthiophene-2,5-diyl)(9,9-dihexyl-fluoren-2,7-diyl) -co-(bipyridine-5.5'-diyl)(9,9-dihexyl-fluoren-2,7-diyl)], is reported. The complexation with platinum was possible through the bipyridil units present in 10%, 50% and 100% content. The structure has a fluorenyl moiety between each bipyridine and thiophene groups resulting in a stable and efficient light-emitting polymeric material combining the well known emissive properties of fluorene, the charge mobility generated by thiophene and the electron-transfer properties of a metal complex as well. All the polymers were photo and electroluminescent materials, and showed phosphorescence at low temperatures. Photoluminescence properties were studied by steady state and time resolved spectroscopy and showed changes of both emission peak and relative intensity of the emission bands depending on the relative amount of the platinum complex. The electroluminescence followed the trends found for photoluminescence. The blue emission of the copolymer without platinum is due to the fluorenyl segments and for higher complex contents the emission is characteristic of the aggregates involving the bipyridinyl moieties. Therefore, emission color can be tuned by the complex content. The turn-on voltage was strongly reduced from 22 to 8 V for the 100% complexed copolymer, as compared to the device made with the non complexed one, but the luminance decreased, due to quenching or trapping effects. - Research Highlights: →Statistic copolymer containing fluorine, thiophene and bipyridine. →Complexation of platinum with platinum with bipyridine. →Electroluminescence and electrophosphorescence at low temperatures. →Emission color can be tuned by the complex content.

Characterization and bacterial anti-adherent effect on modified PMMA denture acrylic resin containing platinum nanoparticles

OpenAIRE

Nam, Ki-Young

2014-01-01

PURPOSE This study characterized the synthesis of a modified PMMA (Polymethyl methacrylate) denture acrylic loading platinum nanoparticles (PtN) and assessed its bacterial inhibitory efficacy to produce novel antimicrobial denture base material. MATERIALS AND METHODS Polymerized PMMA denture acrylic disc (20 mm × 2 mm) specimens containing 0 (control), 10, 50, 100 and 200 mg/L of PtN were fabricated respectively. The obtained platinum-PMMA nanocomposite (PtNC) was characterized by TEM (transm...

Carbon nanotube/platinum nanoparticle nanocomposites: preparation, characterization and application in electro oxidation of alcohols

International Nuclear Information System (INIS)

Kalinke, Adir H.; Zarbin, Aldo J. G.

2014-01-01

The synthesis and characterization of different platinum nanoparticle/ carbon nanotube nanocomposite samples are described along with the application of these nanocomposites as electrocatalysts for alcohol oxidation. Samples were prepared by a biphasic system in which platinum nanoparticles (Pt-NPs) are synthesized in situ in contact with a carbon nanotube (CNT) dispersion. Variables including platinum precursor/CNT ratio, previous chemical treatment of carbon nanotubes, and presence or absence of a capping agent were evaluated and correlated with the characteristic of the synthesized materials. Samples were characterized by Raman spectroscopy, X-ray diffraction, thermogravimetric analysis and transmission electron microscopy. Glassy carbon electrodes were modified by the nanocomposite samples and evaluated as electrocatalysts for alcohol oxidation. Current densities of 56.1 and 79.8/104.7 mA cm -2 were determined for the oxidation of methanol and ethanol, respectively. (author)

Nanostructured gold and platinum electrodes on silicon structures for biosensing

International Nuclear Information System (INIS)

Ogurtsov, V I; Sheehan, M M

2005-01-01

Gold and platinum metal electrodes on Si/SiO 2 having undergone anisotropic potassium hydroxide (KOH) etch treatment are considered. This treatment etches at different rates and directions in the material resulting in creation of numerous pyramid shaped holes in the silicon substrate. This surface is used to make metal electrodes with increased electrode efficiency. The electrodes can serve as the sensors or as the sensor substrates (for surface polymer modification) and because both gold and platinum are inert they have applications for food safety biosensing. Wine, an economically significant food product, was chosen as a matrix, and impedance spectroscopy (EIS) was selected as a method of investigation of electrode behaviour. Based on results of EIS, different complexity equivalent circuits were determined by applying fitting mean square root optimisation of sensor complex impedance measurements

Combined chemotherapy including platinum derivatives for medulloblastoma. The usefulness as maintenance chemotherapy

International Nuclear Information System (INIS)

Sasaki, Hikaru; Otani, Mitsuhiro; Yoshida, Kazunari; Kagami, Hiroshi; Shimazaki, Kenji; Toya, Shigeo; Kawase, Takeshi

1997-01-01

The authors reviewed 24 cerebellar medulloblastoma patients treated at Keio University to determine usefulness of combined chemotherapy including platinum derivatives (cisplatin, carboplatin) as the induction and maintenance treatment. All patients underwent radical surgery and craniospinal irradiation. Ten received adjuvant chemotherapy other than platinum derivatives (mainly with nitrosourea compounds), five were treated by induction and maintenance chemotherapy including platinum derivatives, and nine patients did not undergo chemotherapy. The progression-free survival rate of patients treated with platinum derivatives was better than that of patients treated with other modes of chemotherapy and also that of patients who did not receive chemotherapy. The results were especially good in the case of four patients treated with maintenance chemotherapy consisting of carboplatin and etoposide, two of whom had been free from relapse beyond the risk period of Collins. The occurrences of toxicity in maintenance chemotherapy with carboplatin and etoposide were limited to transient leucopenia. The present study indicates combined chemotherapy including platinum derivatives benefits patients with medulloblastoma, and could be useful, especially as maintenance treatment. (author)

Evaluation of the antitumor activity of platinum nanoparticles in the treatment of hepatocellular carcinoma induced in rats.

Science.gov (United States)

Medhat, Amina; Mansour, Somaya; El-Sonbaty, Sawsan; Kandil, Eman; Mahmoud, Mustafa

2017-07-01

This study aimed to evaluate the antitumor activity of platinum nanoparticles compared with cis-platin both in vitro and in vivo in the treatment of hepatocellular carcinoma induced in rats. The treatment efficacy of platinum nanoparticles was evaluated by measuring antioxidant activities against oxidative stress caused by diethylnitrosamine in liver tissue. The measurements included reduced glutathione content and superoxide dismutase activity, as well as malondialdehyde level. Liver function tests were also determined, in addition to the evaluation of serum alpha-fetoprotein, caspase-3, and cytochrome c in liver tissue. Total RNA extraction from liver tissue samples was also done for the relative quantification of B-cell lymphoma 2, matrix metallopeptidase 9, and tumor protein p53 genes. Histopathological examination was also performed for liver tissue. Results showed that platinum nanoparticles are more potent than cis-platin in treatment of hepatocellular carcinoma induced by diethylnitrosamine in rats as it ameliorated the investigated parameters toward normal control animals. These findings were well appreciated with histopathological studies of diethylnitrosamine group treated with platinum nanoparticles, suggesting that platinum nanoparticles can serve as a good therapeutic agent for the treatment of hepatocellular carcinoma which should attract further studies.

C60 Recognition from Extended Tetrathiafulvalene Bis-acetylide Platinum(II) Complexes.

Science.gov (United States)

Bastien, Guillaume; Dron, Paul I; Vincent, Manon; Canevet, David; Allain, Magali; Goeb, Sébastien; Sallé, Marc

2016-11-18

The favorable spatial organization imposed by the square planar 4,4'-di(tert-butyl)-2,2'-bipyridine (dbbpy) platinum(II) complex associated with the electronic and shape complementarity of π-extended tetrathiafulvalene derivatives (exTTF) toward fullerenes is usefully exploited to construct molecular tweezers, which display good affinities for C 60 .

Mechanical polishing as an improved surface treatment for platinum screen-printed electrodes

Directory of Open Access Journals (Sweden)

Junqiao Lee

2016-07-01

Full Text Available The viability of mechanical polishing as a surface pre-treatment method for commercially available platinum screen-printed electrodes (SPEs was investigated and compared to a range of other pre-treatment methods (UV-Ozone treatment, soaking in N,N-dimethylformamide, soaking and anodizing in aqueous NaOH solution, and ultrasonication in tetrahydrofuran. Conventional electrochemical activation of platinum SPEs in 0.5 M H2SO4 solution was ineffective for the removal of contaminants found to be passivating the screen-printed surfaces. However, mechanical polishing showed a significant improvement in hydrogen adsorption and in electrochemically active surface areas (probed by two different redox couples due to the effective removal of surface contaminants. Results are also presented that suggest that SPEs are highly susceptible to degradation by strong acidic or caustic solutions, and could potentially lead to instability in long-term applications due to continual etching of the binding materials. The ability of SPEs to be polished effectively extends the reusability of these traditionally “single-use” devices. Keywords: Screen-printed electrodes, Polishing, Platinum, Activation, Pre-treatment, Cyclic voltammetry

Structure of matrix metalloproteinase-3 with a platinum-based inhibitor.

Science.gov (United States)

Belviso, Benny Danilo; Caliandro, Rocco; Siliqi, Dritan; Calderone, Vito; Arnesano, Fabio; Natile, Giovanni

2013-06-18

An X-ray investigation has been performed with the aim of characterizing the binding sites of a platinum-based inhibitor (K[PtCl3(DMSO)]) of matrix metalloproteinase-3 (stromelysin-1). The platinum complex targets His224 in the S1' specificity loop, representing the first step in the selective inhibition process (PDB ID code 4JA1).

Same-Side Platinum Electrodes for Metal Assisted Etching of Porous Silicon

Science.gov (United States)

2015-11-01

Platinum Electrodes for Metal Assisted Etching of Porous Silicon by Matthew H Ervin and Brian Isaacson Sensors and Electron Devices Directorate...SUBTITLE Same-Side Platinum Electrodes for Metal Assisted Etching of Porous Silicon 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT

Stabilization of 200-atom platinum nanoparticles by organosilane fragments

KAUST Repository

Pelzer, Katrin

2011-04-19

Three\\'s a charm: Platinum nanoparticles of 2 nm diameter and containing approximately 200 atoms covered with n-octylsilyl groups (see picture, right; Pt blue, Si red, C gray, H turquoise) form when [Pt(dba)2] (dba=dibenzylideneacetone) decomposes in the presence of n-octylsilane. The particles adopt a cuboctahedral structure with an edge length of three atoms. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Stabilization of 200-atom platinum nanoparticles by organosilane fragments

KAUST Repository

Pelzer, Katrin; Hä vecker, Michael; Boualleg, Malika; Candy, Jean Pierre; Basset, Jean-Marie

2011-01-01

Three's a charm: Platinum nanoparticles of 2 nm diameter and containing approximately 200 atoms covered with n-octylsilyl groups (see picture, right; Pt blue, Si red, C gray, H turquoise) form when [Pt(dba)2] (dba=dibenzylideneacetone) decomposes in the presence of n-octylsilane. The particles adopt a cuboctahedral structure with an edge length of three atoms. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Optimising the treatment of the partially platinum-sensitive relapsed ovarian cancer patient

Directory of Open Access Journals (Sweden)

Nicoletta Colombo

2014-12-01

Full Text Available The choice of second-line chemotherapy in patients with recurrent ovarian cancer (ROC is complex, with several factors to be considered, the most important of which is the length of the platinum-free treatment interval (PFI. Recently ROC patients have been further stratified into platinum sensitive (PS, partially platinum sensitive (PPS and platinum resistant (PR subgroups depending on the length of the PFI. Response to second-line therapy, progression-free survival (PFS and overall survival (OS are linked to the PFI, all of them improving as the PFI increases. Consequently, there is increasing interest in PFI extension strategies with platinum-free therapeutic options. Such strategies are currently being studied in patients with partially platinum-sensitive disease (PFI 6-12 months, as the treatment of these patients remains clinically challenging. A non-platinum option, trabectedin + pegylated liposomal doxorubicin (PLD combination, has been evaluated in ROC patients in the pivotal phase III OVA-301 study. The OVA-301 study differed from previous trials in the same setting as it included only patients who were not expected to benefit from or who were ineligible for or who were unwilling to receive re-treatment with platinum-based chemotherapy, including those with PPS and PR disease. Subset analysis of patients with PPS disease in OVA-301 showed that the trabectedin + PLD combination significantly improved PFS compared with PLD alone; median PFS 7.4 versus 5.5 months, p=0.0152. Final survival data from the same subset of patients, showed that trabectedin + PLD also achieved a significant 36% decrease in the risk of death compared with PLD alone (HR=0.64; 95% CI, 0.47–0.88; p=0.0027. Median overall survival (OS was 22.4 months in the trabectedin + PLD arm versus 16.4 months in the PLD arm. This represents a statistically significant 6-month improvement in median OS in patients treated with trabectedin + PLD compared to those treated with PLD

Electrochemical behaviour of platinum in hydrogen peroxide solution (1963)

International Nuclear Information System (INIS)

Prost, G.H.

1963-06-01

The relative stability of hydrogen peroxide in aqueous solution at 25 deg. C, allows its amperometric determination from the theory, using either its cathodic reduction or its anodic oxidation. The cathodic reduction yields a wave on a platinum electrode only when some oxygen is present in the solution. It cannot, therefore, be used for electrochemical determination. On the other hand, the anodic oxidation on platinum produces a wave which might be used. However, a passivation of platinum occurs at the same time. This passivation process is studied by means of potentio-kinetic, potentio-static, intensio-static curves and of pH measurements in the vicinity of the anode. A mechanism for passivation is presented, which takes into account the role of hydrogen peroxide as a reducing agent. This passivation rules out any analytical application of the oxidation reaction of hydrogen peroxide. (author) [fr

PLD prepared nanostructured Pt-CeO{sub 2} thin films containing ionic platinum

Energy Technology Data Exchange (ETDEWEB)

Vorokhta, M., E-mail: vorohtam@gmail.com [Charles University in Prague, Faculty of Mathematics and Physics, Department of Surface and Plasma Science, V Holešovičkách 2, 18000 Prague 8 (Czech Republic); Khalakhan, I.; Matolínová, I.; Nováková, J.; Haviar, S. [Charles University in Prague, Faculty of Mathematics and Physics, Department of Surface and Plasma Science, V Holešovičkách 2, 18000 Prague 8 (Czech Republic); Lančok, J.; Novotný, M. [Institute of Physics, Academy of Sciences of the Czech Republic, Na Slovance 2, 182 21 Prague, Czhech Republic (Czech Republic); Yoshikawa, H. [National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan); Matolín, V. [Charles University in Prague, Faculty of Mathematics and Physics, Department of Surface and Plasma Science, V Holešovičkách 2, 18000 Prague 8 (Czech Republic)

2017-02-28

Highlights: • Nanostructured Pt-CeO{sub 2} thin catalyst films were grown on plasma etched and non-etched carbon substrates by pulsed laser deposition. • The surface composition of the nanostructured Pt-CeO{sub 2} films was investigated by surface analysis techniques. • The effect of film roughening was separated from the effect of platinum-ceria atomic interactions. - Abstract: The composition of nanostructured Pt-CeO{sub 2} films on graphite substrates prepared by pulsed laser deposition has been investigated by means of hard X-ray photoelectron spectroscopy, scanning electron microscopy, high resolution transmission electron microscopy, and atomic force microscopy. The influence of morphology of the graphite substrates was investigated with respect to the relative concentrations of ionic and metallic Pt species in the films. It was found that the degree of Pt{sup 2+} enrichment is directly related to the surface morphology of graphite substrates. In particular, the deposition of Pt-CeO{sub 2} films on rough graphite substrate etched in oxygen plasma yielded nanostructured Pt-CeO{sub 2} catalyst films with high surface area and high Pt{sup 2+}/Pt{sup 0} ratio. The presented results demonstrate that PLD is a suitable method for the preparation of thin Pt-CeO{sub 2} catalyst films for fuel cell applications.

The determination, by atomic-absorption spectrophotometry using electrothermal atomization, of platinum, palladium, rhodium, ruthenium, and iridium

International Nuclear Information System (INIS)

Haines, J.; Robert, R.V.D.

1982-01-01

A method that involves measurement by atomic-absorption spectrophotometry using electrothermal atomization has been developed for the determination of trace quantities of platinum, palladium, rhodium, ruthenium, and iridium in mineralogical samples. The elements are separated and concentrated by fusion, nickel sulphide being used as the collector, and the analyte elements are measured in the resulting acid solution. An organic extraction procedure was found to offer no advantages over the proposed method. Mutual interferences between the five platinum-group metals examined, as well as interferences from gold, silver, and nickel were determined. The accuracy of the measurement was established by the analysis of a platinum-ore reference material. The lower limits of determination of each of the analyte elements in a sample material are as follows: platinum 1,6μg/l, palladium 0,2μg/1, rhodium 0,5μg/l, ruthenium 3μg/l, and iridium 2,5μg/l. The relative standard deviations range from 0,05 for rhodium to 0.08 for iridium. The method, which is described in detail in the Appendix, is applicable to the determination of these elements in ores, tailings, and geological materials in which the total concentration of the noble metals is less than 1g/t

Detection limits in the chromatographic element trace analysis - quantitative TLC, HPLC and GC with the example of beryllium acetylacetonate

International Nuclear Information System (INIS)

Schwedt, G.

1981-01-01

Chromatographic analyses of beryllium acetylacetonate are carried out in synthetic solutions within the nano- and picogram range of beryllium. For thin-layer chromatography (TLC) normal and silanized silica gel is used, for high-performance liquid chromatography (HPLC) silica gel of 7 μm particles, for gas chromatography (GC) silicone SE-30 as stationary phase. Visual evaluation and remission measurements in TLC, UV-254 nm absorption measurements in HPLC and measurements with a FID in GC are employed for the determination of the calibration curves. A calibration curve through the origin and a detection limit of 150 pg Be determinable form are received by HPLC only. For trace analyses by GC a new definition of a detection limit for the evaluation of substance peaks on a solvent tailing is suggested. (orig.) [de

Stability of Porous Platinum Nanoparticles: Combined In Situ TEM and Theoretical Study

DEFF Research Database (Denmark)

Chang, Shery L. Y.; Barnard, Amanda S.; Dwyer, Christian

2012-01-01

Porous platinum nanoparticles provide a route for the development of catalysts that use less platinum without sacrificing catalytic performance. Here, we examine porous platinum nanoparticles using a combination of in situ transmission electron microscopy and calculations based on a first-principles......-parametrized thermodynamic model. Our experimental observations show that the initially irregular morphologies of the as-sythesized porous nanoparticles undergo changes at high temperatures to morphologies having faceted external surfaces with voids present in the interior of the particles. The increasing size of stable...

Phosphorescent Organic Light Emitting Diodes Implementing Platinum Complexes

Science.gov (United States)

Ecton, Jeremy Exton

Organic light emitting diodes (OLEDs) are a promising approach for display and solid state lighting applications. However, further work is needed in establishing the availability of efficient and stable materials for OLEDs with high external quantum efficiency's (EQE) and high operational lifetimes. Recently, significant improvements in the internal quantum efficiency or ratio of generated photons to injected electrons have been achieved with the advent of phosphorescent complexes with the ability to harvest both singlet and triplet excitons. Since then, a variety of phosphorescent complexes containing heavy metal centers including Os, Ni, Ir, Pd, and Pt have been developed. Thus far, the majority of the work in the field has focused on iridium based complexes. Platinum based complexes, however, have received considerably less attention despite demonstrating efficiency's equal to or better than their iridium analogs. In this study, a series of OLEDs implementing newly developed platinum based complexes were demonstrated with efficiency's or operational lifetimes equal to or better than their iridium analogs for select cases. In addition to demonstrating excellent device performance in OLEDs, platinum based complexes exhibit unique photophysical properties including the ability to form excimer emission capable of generating broad white light emission from a single emitter and the ability to form narrow band emission from a rigid, tetradentate molecular structure for select cases. These unique photophysical properties were exploited and their optical and electrical properties in a device setting were elucidated. Utilizing the unique properties of a tridentate Pt complex, Pt-16, a highly efficient white device employing a single emissive layer exhibited a peak EQE of over 20% and high color quality with a CRI of 80 and color coordinates CIE(x=0.33, y=0.33). Furthermore, by employing a rigid, tetradentate platinum complex, PtN1N, with a narrow band emission into a

Poly(N-vinyl-2-pyrrolidone)-stabilized palladium-platinum nanoparticles-catalyzed hydrolysis of ammonia borane for hydrogen generation

Science.gov (United States)

Rakap, Murat

2015-02-01

The catalytic use of highly efficient poly(N-vinyl-2-pyrrolidone)-stabilized palladium-platinum nanoparticles (4.2 ± 1.9 nm) in the hydrolysis of ammonia-borane is reported. The catalyst is prepared by co-reduction of two metal ions in ethanol/water mixture by an alcohol reduction method and characterized by transmission electron microscopy, X-ray photoelectron spectroscopy and UV-Vis spectroscopy. They are recyclable and highly active for hydrogen generation from the hydrolysis of ammonia-borane even at very low concentrations and temperature, providing a record numbers of average turnover frequency value (125 mol H2/mol cat.min-1) and maximum hydrogen generation rate (3468 L H2 min-1 (mol cat)-1). They also provide activation energy of 51.7 ± 2 kJ/mol for the hydrolysis of ammonia borane.

Pharmacogenetic predictors of toxicity to platinum based chemotherapy in non-small cell lung cancer patients.

Science.gov (United States)

Pérez-Ramírez, Cristina; Cañadas-Garre, Marisa; Alnatsha, Ahmed; Villar, Eduardo; Delgado, Juan Ramón; Faus-Dáder, María José; Calleja-Hernández, Miguel Ÿngel

2016-09-01

Platinum-based chemotherapy is the standard treatment for NSCLC patients with EGFR wild-type, and as alternative to failure to EGFR inhibitors. However, this treatment is aggressive and most patients experience grade 3-4 toxicities. ERCC1, ERCC2, ERCC5, XRCC1, MDM2, ABCB1, MTHFR, MTR, SLC19A1, IL6 and IL16 gene polymorphisms may contribute to individual variation in toxicity to chemotherapy. The aim of this study was to evaluate the effect of these polymorphisms on platinum-based chemotherapy in NSCLC patients. A prospective cohorts study was conducted, including 141 NSCLC patients. Polymorphisms were analyzed by PCR Real-Time with Taqman(®) probes and sequencing. Patients with ERCC1 C118T-T allele (p=0.00345; RR=26.05; CI95%=4.33, 515.77) and ERCC2 rs50872-CC genotype (p=0.00291; RR=4.06; CI95%=1.66, 10.65) had higher risk of general toxicity for platinum-based chemotherapy. ERCC2 Asp312Asn G-alelle, ABCB1 C1236T-TT and the IL1B rs12621220-CT/TT genotypes conferred a higher risk to present multiple adverse events. The subtype toxicity analysis also revealed that ERCC2 rs50872-CC genotype (p=0.01562; OR=3.23; CI95%=1.29, 8.82) and IL16 rs7170924-T allele (p=0.01007; OR=3.19; CI95%=1.35, 7.97) were associated with grade 3-4 hematological toxicity. We did not found the influence of ERCC1 C8092A, ERCC2 Lys751Gln, ERCC2 Asp312Asn, ERCC5 Asp1104His, XRCC1 Arg194Trp, MDM2 rs1690924, ABCB1 C3435T, ABCB1 Ala893Ser/Thr, MTHFR A1298C, MTHFR C677T, IL1B rs1143623, IL1B rs16944, and IL1B rs1143627 on platinum-based chemotherapy toxicity. In conclusion, ERCC1 C118T, ERCC2 rs50872, ERCC2 Asp312Asn, ABCB1 C1236T, IL1B rs12621220 and IL16 rs7170924 polymorphisms may substantially act as prognostic factors in NSCLC patients treated with platinum-based chemotherapy. Copyright © 2016 Elsevier Ltd. All rights reserved.

Electrodeposition of platinum metals and alloys from chloride melts

Directory of Open Access Journals (Sweden)

Saltykova N.A.

2003-01-01

Full Text Available The structure of platinum metals and their alloys deposited by the electrolysis of chloride melts have been investigated. The cathodic deposits were both in the form of compact layers and dendrites. All the alloys of platinum metals obtained are solid solutions in the whole range of composition. Depending on the experimental conditions the layers had columnar, stratum and spiral (dissipative structures. The stratum and dissipative structures were observed in the case of alloys only.

The exchange reaction between deuterium and water vapour on platinum deposited over a hydrophobic support

International Nuclear Information System (INIS)

Itsuo, Iida; Junko, Kato; Kenzi, Tamuru

1977-01-01

Isotope exchange reaction between deuterium gas and water vapour at room temperature and below on platinum deposited on hydrophobic supports such as polytetrafluoroethylene (PTFE) or Porapak Q (copolymer of styrene and divinylbenzene) was studied and the results were compared with those of the exchange reaction on platinum over hydrophilic support such as alumina. It was demonstrated that the exchange reaction at temperatures below the boiling point of water is markedly retarded by the multilayer adsorption of water over the platinum catalyst deposited on hydrophilic support, whereas the platinum catalyst on hydrophobic support exhibited a high catalytic activity, being not retarded by the water, forming no multilayer of adsorbed water over platinum surface. Therefore in the case of the hydrogen isotope exchange reaction on platinum over hydrophobic support, the chemical exchange rate can be measured even under a saturated vapour pressure of water. The surface area of platinum was estimated by hydrogen chemisorption and hydrogen titration and specific activities of the catalyst were calculated at both room temperature and freezing point of water, which revealed that the specific rate of this reaction does not differ so much over various supports. (orig.) [de

Ultra-small platinum and gold nanoparticles by arc plasma deposition

International Nuclear Information System (INIS)

Kim, Sang Hoon; Jeong, Young Eun; Ha, Heonphil; Byun, Ji Young; Kim, Young Dok

2014-01-01

Highlights: • Ultra-small (<2 nm) and bigger platinum and gold nanoparticles were produced by arc plasma deposition (APD). • Size and coverage of deposited nanoparticles were easily controlled with APD parameters. • Crystalline structures of deposited nanoparticles emerged only when the particle size was bigger than ∼2 nm. - Abstract: Ultra-small (<2 nm) nanoparticles of platinum and gold were produced by arc plasma deposition (APD) in a systematic way and the deposition behavior was studied. Nanoparticles were deposited on two dimensional amorphous carbon and amorphous titania thin films and characterized by transmission electron microscopy (TEM). Deposition behavior of nanoparticles by APD was studied with discharge voltage (V), discharge condenser capacitance (C), and the number of plasma pulse shots (n) as controllable parameters. The average size of intrinsic nanoparticles generated by APD process was as small as 0.9 nm and deposited nanoparticles began to have crystal structures from the particle size of about 2 nm. V was the most sensitive parameter to control the size and coverage of generated nanoparticles compared to C and n. Size of APD deposited nanoparticles was also influenced by the nature of evaporating materials and substrates

A combined radiation and platinum chemotherapy for esophageal carcinoma

International Nuclear Information System (INIS)

Takamura, Akio; Saito, Hiroya; Sakurai, Yasuo; Horio, Keiji; Mizoe, Junetsu.

1993-01-01

The prognosis of the patients with advanced esophageal carcinoma treated by definitive radiotherapy is still dismal with a reported 5-year survival rate of 5-10% in most series. Since 1986, combined radiotherapy with chemotherapy using platinum analogue was initiated at Asahikawa and Obihiro Kosei Hospitals in order to improve local-regional control and the survival of the patients. From 1980 to 1992, 81 patients with unresectable esophageal carcinoma were treated with radiotherapy. Since April 1986, 37 out of the 81 patients received both radiotherapy and chemotherapy with platinum. Platinum was used during the course of radiotherapy. The method of administration of platinum was as follows; Cisplatin intravenously (50 mg, weekly, total 200 mg) in 9 patients, Carboplatin intravenously (100-150 mg, weekly, total 400-900 mg) in 11 patients and Cisplatin intraarterially (100 mg, at a 3-4 week interval, total 100-300 mg) in 17 patients. These 37 patients (Group A) were compared to 44 patients treated by radiotherapy alone (Group B) with respect to initial response and survival rate. Response was defined according to the guidelines recommended by Japanese Society for Esophageal Diseases. Response rates were 59.1% (19 CR and 7 PR) in Group B and 70.3% (7 CR and 19 PR) in Group A. Primary relapse-free rates were 36.4% in Group B and 37.8% in Group A. The cumulative survival at 3 years were 11.7% in Group B and 10.6% in Group A. Enhancement of side effects by chemotherapy was minimal and acceptable. Improvement of local-regional control and survival was not obvious by adding a concomitant platinum-chemotherapy. A definite conclusion, however, could not be drawn because of the retrospective, non-controlled nature of this study. Introduction of more intensive, multiple agents chemotherapy seems necessary if one aims at improving the results. (author)

Enhancement of micropore filling of water on carbon black by platinum loading

Energy Technology Data Exchange (ETDEWEB)

Miyajima, Naoya, E-mail: miyajima@yamanashi.ac.jp [Interdisciplinary Graduate School of Medicine and Engineering, 4-3-11 Takeda, Kofu, Yamanashi 400-8511 (Japan); Hatori, Hiroaki [Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, Ibaraki 305-8569 (Japan); Radovic, Ljubisa R. [Department of Energy and Geo-Environmental Engineering, The Pennsylvania State University, University Park, PA 16802 (United States); Yamada, Yoshio [Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, Ibaraki 305-8569 (Japan)

2010-10-15

Two kinds of typical carbons, carbon black and activated carbon fibers, were modified with platinum nanoparticles without changing their original pore structures. The surface properties of the modified carbons were investigated by measuring of water adsorption isotherms. Micropore filling of water was facilitated by the presence of platinum nanoparticles on the surface of the carbon black. On the other hand, such a filling effect was not observed in the case of the activated carbon fibers. A critical content and/or size of platinum nanoparticles could be required to promote efficiently the water adsorption.

One step synthesis of chlorine-free Pt/Nitrogen-doped graphene composite for oxygen reduction reaction

KAUST Repository

Varga, Tamás

2018-03-14

Chlorine-free Platinum/nitrogen-doped graphene oxygen reduction reaction catalysts were synthesized by a one step method of annealing a mixture of platinum acetylacetonate and graphene oxide under ammonia atmosphere. Nanoparticles with close to the ideal particle size for oxygen reduction reaction (ORR) were formed, i.e., with diameter of 3–4 nm (500 and 600 °C) and 6 nm (700 °C). X-ray photoelectron spectroscopy confirmed the successful introduction of both pyridinic and pyrrolic type nitrogen moieties into the graphene layers, which indicates a strong interaction between the nanoparticles and the graphene layers. The electrocatalytic activity of glassy carbon electrodes (GCE) modified with the synthesized Pt/NG samples for oxygen reduction was compared to that of a platinum/carbon black catalyst modified electrode in acidic and alkaline media. Based on the measured limiting current densities and calculated electron transfer number, the highest activity was measured in acidic and alkaline media on the samples annealed at 600 and 700 °C, respectively.

Biosorption of platinum and palladium for their separation/preconcentration prior to graphite furnace atomic absorption spectrometric determination

Energy Technology Data Exchange (ETDEWEB)

Godlewska-Zylkiewicz, Beata E-mail: bgodlew@uwb.edu.pl

2003-08-15

Inexpensive baker's yeast Saccharomyces cerevisiae and green algae Chlorella vulgaris, either free or immobilized on silica gel have been shown to selectively accumulate platinum and palladium from water samples in acidic medium (pH 1.6-1.8). Optimization of conditions of metals biosorption (sample pH, algae and yeast masses, adsorption time, temperature) was performed in batch mode. The procedure of matrix separation based on biosorption of platinum and palladium on algae C. vulgaris covalently immobilized on silica gel in flow mode was developed. The use of algae in flow procedure offers several advantages compared with its use in the batch mode. The procedure shows better reproducibility (<2%), improved efficiency of platinum retention on the column (93.3{+-}1.6%), is less laborious and less time consuming. The best recovery of biosorbed metals from column (87.7{+-}3.3% for platinum and 96.8{+-}1.1 for palladium) was obtained with solution of 0.3 mol l{sup -1} thiourea in 1 mol l{sup -1} hydrochloric acid. The influence of thiourea on analytical signals of examined metals during GFAAS determination is discussed. The procedure has been applied for separation of noble metals from tap and waste water samples spiked with platinum and palladium.

The energy of hydration and solvation of indium salts in the acetylacetone-InCl3-water system

International Nuclear Information System (INIS)

Kulawik, I.; Baumgartner, T.

1978-01-01

On the base of the previous papers concerning the investigations in the extraction systems the experiments were performed for the determination of thermodynamical distribution coefficient of indium salts between two phases in the system: acetylacetone-InCl 3 -water and the energy of hydration and solvation of that system. The results of the surface and interfacial potentials measurements of the system were presented as a function of the InCl 3 concentration in the system before the extraction. The extraction coefficients of indium as a function of concentration of InCl 3 in this system were determined. The method of the visible absorption spectra was used to the determination of concentration of indium in both phases after the extraction. The relation between the percentage of the extraction and the extraction coefficient was determined. The investigations were performed in the system containing 0.1 M HCl and 0.001 M HCl in the aqueous phase. The results of experiments are tabulated and graphically presented in figures. (author)

Electron transfer processes occurring on platinum neural stimulating electrodes: pulsing experiments for cathodic-first, charge-balanced, biphasic pulses for 0.566  ⩽  k  ⩽  2.3 in rat subcutaneous tissues

Science.gov (United States)

Kumsa, Doe W.; Bhadra, Narendra; Hudak, Eric M.; Mortimer, J. Thomas

2017-10-01

Objective. Our mission is twofold: (1) find a way to safely inject more charge through platinum electrodes than the Shannon limit (k  =  1.75) permits and (2) nurture an interest in the neural stimulation community to understand the electron transfer process occurring on neural stimulating electrodes. Approach. We report here on measurements of the electrode potential, performed on platinum neural stimulating electrodes in the subcutaneous space of an anesthetized rat under neural stimulation conditions. Main results. The results for six platinum electrodes with areas ranging from 0.2 mm2 to 12.7 mm2 were similar to prior results in sulfuric acid, except that the measured potentials were shifted negative 0.36 V because of the pH difference between the two media. The anodic ‘end’ potential, measured at t  =  20 ms after the onset of the biphasic current pulse, was the primary focus of the data collected because previous results had shown that as charge injection crosses the Shannon limit (k  =  1.75), this potential moves into a range where platinum surface oxidation and dissolution is likely to occur. The behavior of V e(t  =  20 ms) over a range of electrode surface areas studied was consistent with our sulfuric acid study. Implicit, but little noticed, in Shannon’s formulation is that small and large platinum electrodes behave the same in terms of k value; our data supports this idea. Significance. We hypothesize that the k  =  1.75 Shannon limit for safe stimulation designates a charge-injection boundary above which platinum toxicity becomes a relevant consideration for living cells around an electrode, a possibility that can be directly tested, and is a vital step forward in mission (1).

Origin of the different behavior of some platinum decorated nanocarbons towards the electrochemical oxidation of hydrogen peroxide

International Nuclear Information System (INIS)

Malara, A.; Leonardi, S.G.; Bonavita, A.; Fazio, E.; Stelitano, S.; Neri, G.; Neri, F.; Santangelo, S.

2016-01-01

The electrochemical behavior of different platinum-decorated nanocarbons (Pt@C) towards the oxidation of hydrogen peroxide (H_2O_2) was investigated. Three different types of nanocarbons were considered: i) carbon black, ii) dahlia-like carbon nanohorns and iii) carbon nanotubes, which included both commercial (single-wall and multi-wall) and laboratory prepared (multi-wall) samples. Shape and size distribution of the platinum nanoparticles and morphology of the nanocarbons were analyzed by transmission electron microscopy. Their nanostructure was investigated by micro-Raman spectroscopy, while elemental composition of the samples and chemical bonding states were studied by X-ray photoelectron spectroscopy. Electrochemical behavior towards H_2O_2 oxidation was evaluated by means of cyclic voltammetry modifying the working screen-printed carbon electrode surface with the prepared Pt@C nanocomposites. Data obtained suggest that the size and dispersion of the Pt nanoparticles play a key role in increasing the sensitivity towards H_2O_2 detection. Thanks to the presence of smaller and more dispersed platinum particles and of a greater amount of platinum hydroxide, acting as intermediary in the H_2O_2 oxidation process, Pt@dahlia-like carbon nanohorns result to be the most promising platform for the development of H_2O_2 electrochemical sensors. - Highlights: • Different nanocarbons are decorated with Pt nanoparticles by wet impregnation method. • Pt@C-based hybrids are tested as active materials for sensing of hydrogen peroxide. • Sensor based on Pt@dahlia-like carbon nanohorns is the most performing device. • The origin of the different electrochemical behaviour is investigated. • Pt@C sensing performances are correlated with their structural and surface properties.

Electrochemical behaviour of gamma hydroxybutyric acid at a platinum electrode in acidic medium

International Nuclear Information System (INIS)

Jiménez-Pérez, R.; Sevilla, J.M.; Pineda, T.; Blázquez, M.; González-Rodríguez, J.

2013-01-01

Highlights: • This is the first reported electrochemical study of the behaviour of GHB. • The first study of the interaction of GHB on solid electrodes. • The GHB oxidation process in platinum electrodes is a complex process. • Re-dissolution and reduction of Pt oxides and oxidation of the GHB OH group. • The oxidation process is also influenced by pH and GHB concentration. -- Abstract: The electrooxidation of gamma hydroxybutyric acid (GHB) on a polycrystalline platinum electrode is studied by cyclic voltammetry in acidic medium. Two oxidation peaks, A and B, are obtained in the positive scan within the potential range of the double layer region and of the platinum oxide region, respectively. In the negative going potential sweep an inverted oxidation peak with an onset partially overlapping with the tail of the cathodic peak for the reduction of the platinum oxide formed during the anodic scan is obtained (peak C). This inverted peak can be observed at a potential close to +0.2 V (vs Ag/AgCl at pH 2) and separated 0.4 and 0.8 V from the two other oxidation peaks obtained during the anodic scan and in such conditions that the surface is particularly activated to favour this electrochemical process. The response obtained in the electronic current for the different peaks when GHB concentration and scan rate were changed to allows inferring that these are the result of a potential dependent mechanism. The behaviour observed is according with the oxidation of the alcohol group to the corresponding aldehyde and carboxylic acid (succinic acid) as main products

Concentrations of Platinum Group Elements (Pt, Pd, Rh) in Airborne Particulate Matter (PM2.5 and PM10-2.5) Collected at Selected Canadian Urban Sites: a Case Study

OpenAIRE

Celo V.; Zhao J. J.; Dabek-Zlotorzynska E.

2013-01-01

Increasing environmental concentrations of platinum group elements (PGEs), in particular platinum (Pt), palladium (Pd) and rhodium (Rh), from catalytic converters has been reported worldwide. Initially it was believed that the emitted PGEs remain in the roadside environment, but recent studies have shown that fine PGE-containing particles can be transported and distributed at regional and long-range levels. Therefore, the monitoring of PGEs in airborne particulate matter (PM) is important for...

Electrochemical DNA biosensors based on platinum nanoparticles combined carbon nanotubes

International Nuclear Information System (INIS)

Zhu Ningning; Chang Zhu; He Pingang; Fang Yuzhi

2005-01-01

Platinum nanoparticles were used in combination with multi-walled carbon nanotubes (MWCNTs) for fabricating sensitivity-enhanced electrochemical DNA biosensor. Multi-walled carbon nanotubes and platinum nanoparticles were dispersed in Nafion, which were used to fabricate the modification of the glassy carbon electrode (GCE) surface. Oligonucleotides with amino groups at the 5' end were covalently linked onto carboxylic groups of MWCNTs on the electrode. The hybridization events were monitored by differential pulse voltammetry (DPV) measurement of the intercalated daunomycin. Due to the ability of carbon nanotubes to promote electron-transfer reactions, the high catalytic activities of platinum nanoparticles for chemical reactions, the sensitivity of presented electrochemical DNA biosensors was remarkably improved. The detection limit of the method for target DNA was 1.0 x 10 -11 mol l -1

Discovery of the calcium, indium, tin, and platinum isotopes

International Nuclear Information System (INIS)

Amos, S.; Gross, J.L.; Thoennessen, M.

2011-01-01

Currently, twenty-four calcium, thirty-eight indium, thirty-eight tin, and thirty-nine platinum isotopes have been observed and the discovery of these isotopes is discussed here. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented. - Highlights: Documentation of the discovery of all calcium, indium, tin and platinum isotopes. → Summary of author, journal, year, place and country of discovery for each isotope. → Brief description of discovery history of each isotope.

The relationship between debt levels and total shareholder return of JSE-listed platinum companies

Directory of Open Access Journals (Sweden)

Sandra Jooste

2016-02-01

Full Text Available The purpose of this study is to investigate empirically whether there is a positive correlation between debt levels and total shareholder return (TSR of platinum JSE-listed companies. The study field comprised annual analyses for 12 companies listed under the Platinum and Precious Metals sector on the JSE Ltd for the 14-year period 2000 to 2013. The results of the study were inconclusive as a statistically significant positive correlation between changes in debt levels and changes in TSR could only be found in two of these years. The core audience of the study will be the management of South African platinum companies considering changes in their capital structure, and investors considering investment in a listed platinum company. The contribution of the study is therefore to add to the body of literature on capital structure decisions from a South African platinum mine context

Sub-10 nm structures on silicon by thermal dewetting of platinum

International Nuclear Information System (INIS)

Strobel, Sebastian; Kirkendall, Christopher; Chang, Jae-Byum; Berggren, Karl K

2010-01-01

A study of the dewetting behavior of platinum-thin-films on silicon was carried out to determine how variation of dewetting parameters affects the evolution of film morphology and to pinpoint which parameters yielded the smallest, most circular features. Platinum film thickness as well as dewetting time and temperature were varied and the film morphology characterized by means of scanning electron microscopy (SEM) analysis. Two different pathways of dewetting predicted in the literature (Vrij 1966 Discuss. Faraday Soc. 42 23, Becker et al 2003 Nat. Mater. 2 59-63) were observed. Depending on the initial criteria, restructuring of the film occurred via hole or droplet formation. With increased annealing time, a transition from an intermediate network structure to separated islands occurred. In addition, the formation of multilayered films, silicide crystals and nanowires occurred for certain parameters. Nevertheless, the dewetting behavior witnessed could be related to physical processes. Droplets with a mean diameter of 9 nm were formed by using a 1.5 nm thick platinum film annealed at 800 deg. C for 30 s. To demonstrate the suitability of the annealed films for further processing, we then used the dewetted films as masks for reactive ion etching to transfer the pattern into the silicon substrate, forming tapered nanopillars.

Multicenter retrospective study of cetuximab plus platinum-based chemotherapy for recurrent or metastatic oral squamous cell carcinoma.

Science.gov (United States)

Yanamoto, Souichi; Umeda, Masahiro; Kioi, Mitomu; Kirita, Tadaaki; Yamashita, Tetsuro; Hiratsuka, Hiroyoshi; Yokoo, Satoshi; Tanzawa, Hideki; Uzawa, Narikazu; Shibahara, Takahiko; Ota, Yoshihide; Kurita, Hiroshi; Okura, Masaya; Hamakawa, Hiroyuki; Kusukawa, Jingo; Tohnai, Iwai

2018-03-01

The purpose of this study was to assess the efficacy and safety of cetuximab plus platinum-based chemotherapy for patients specifically diagnosed with recurrent or metastatic oral squamous cell carcinoma (OSCC). We conducted a multicenter retrospective observational study of patients who underwent first-line cetuximab plus platinum-based chemotherapy between December 2012 and June 2015. 65 patients received weekly cetuximab (week 1, 400 mg/m 2 ; subsequent weeks, 250 mg/m 2 ) plus a maximum of six 3-weekly cycles of cisplatin (80 or 100 mg/m 2 , day 1) or carboplatin (at an area under the curve of 5 mg/mL/min as a 1-h intravenous infusion on day 1) and 5-fluorouracil (800 or 1000 mg/m 2 /day, days 1-4). Patients with stable disease who received cetuximab plus platinum-based chemotherapy continued to receive cetuximab until disease progression or unacceptable toxicities, whichever occurred first. The median follow-up was 10.5 (range 1.2-34.2) months. The best overall response and the disease control rates were 46.2 and 67.7%, respectively. The median overall survival and progression-free survival rates were 12.1 and 7.8 months, respectively. The most common grades 3-4 adverse events were skin rash (9.2%) followed by leukopenia (6.2%). None of the adverse events were fatal. The results of our multicenter retrospective study, which was the largest of its kind to date, suggest that first-line cetuximab plus platinum-based chemotherapy is suitable and well-tolerated for the systemic therapy of recurrent or metastatic OSCC.

Inhibition of ammonia poisoning by addition of platinum to Ru/α-Al2 O3 for preferential CO oxidation in fuel cells.

Science.gov (United States)

Sato, Katsutoshi; Yagi, Sho; Zaitsu, Shuhei; Kitayama, Godai; Kayada, Yuto; Teramura, Kentaro; Takita, Yusaku; Nagaoka, Katsutoshi

2014-12-01

In polymer electrolyte fuel cell (PEFC) systems, small amounts of ammonia (NH3 ) present in the reformate gas deactivate the supported ruthenium catalysts used for preferential oxidation (PROX) of carbon monoxide (CO). In this study, we investigated how the addition of a small amount of platinum to a Ru/α-Al2 O3 catalyst (Pt/Ru=1:9 w/w) affected the catalyst's PROX activity in both the absence and the presence of NH3 (130 ppm) under conditions mimicking the reformate conditions during steam reforming of natural gas. The activity of undoped Ru/α-Al2 O3 decreased sharply upon addition of NH3 , whereas Pt/Ru/α-Al2 O3 exhibited excellent PROX activity even in the presence of NH3 . Ruthenium K-edge X-ray absorption near-edge structure (XANES) spectra indicated that in the presence of NH3 , some of the ruthenium in the undoped catalyst was oxidized in the presence of NH3 , whereas ruthenium oxidation was not observed with Pt/Ru/α-Al2 O3 . These results suggest that ruthenium oxidation is retarded by the platinum, so that the catalyst shows high activity even in the presence of NH3 . © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Durability of Low Platinum Fuel Cells Operating at High Power Density

Energy Technology Data Exchange (ETDEWEB)

Polevaya, Olga [Nuvera Fuel Cells Inc.; Blanchet, Scott [Nuvera Fuel Cells Inc.; Ahluwalia, Rajesh [Argonne National Lab; Borup, Rod [Los-Alamos National Lab; Mukundan, Rangachary [Los-Alamos National Lab

2014-03-19

Understanding and improving the durability of cost-competitive fuel cell stacks is imperative to successful deployment of the technology. Stacks will need to operate well beyond today’s state-of-the-art rated power density with very low platinum loading in order to achieve the cost targets set forth by DOE ($15/kW) and ultimately be competitive with incumbent technologies. An accelerated cost-reduction path presented by Nuvera focused on substantially increasing power density to address non-PGM material costs as well as platinum. The study developed a practical understanding of the degradation mechanisms impacting durability of fuel cells with low platinum loading (≤0.2mg/cm2) operating at high power density (≥1.0W/cm2) and worked out approaches for improving the durability of low-loaded, high-power stack designs. Of specific interest is the impact of combining low platinum loading with high power density operation, as this offers the best chance of achieving long-term cost targets. A design-of-experiments approach was utilized to reveal and quantify the sensitivity of durability-critical material properties to high current density at two levels of platinum loading (the more conventional 0.45 mgPt.cm–1 and the much lower 0.2 mgPt.cm–2) across several cell architectures. We studied the relevance of selected component accelerated stress tests (AST) to fuel cell operation in power producing mode. New stress tests (NST) were designed to investigate the sensitivity to the addition of electrical current on the ASTs, along with combined humidity and load cycles and, eventually, relate to the combined city/highway drive cycle. Changes in the cathode electrochemical surface area (ECSA) and average oxygen partial pressure on the catalyst layer with aging under AST and NST protocols were compared based on the number of completed cycles. Studies showed elevated sensitivity of Pt growth to the potential limits and the initial particle size distribution. The ECSA loss

Oscillatory instabilities in the electrooxidation of borohydride on platinum

Energy Technology Data Exchange (ETDEWEB)

Machado, Eduardo G.; Varela, Hamilton, E-mail: varela@iqsc.usp.br [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Instituto de Quimica

2014-03-15

The borohydride ion has been pointed as a promising alternative fuel. Most of the investigation on its electrochemistry is devoted to the electrocatalytic aspects of its electrooxidation on platinum and gold surfaces. Besides the known kinetic limitations and intricate mechanism, our Group has recently found the occurrence of two regions of bi-stability and autocatalysis in the electrode potential during the open circuit interaction of borohydride and oxidized platinum surfaces. Following this previous contribution, the occurrence of more complicated phenomena is here presented: namely the presence of electrochemical oscillations during the electrooxidation of borohydride on platinum in alkaline media. Current oscillations were found to be associated to two distinct instability windows and characterized in the resistance-potential parameter plane. The dynamic features of such oscillations suggest the existence of distinct mechanisms according to the potential region. Previously published results obtained under non-oscillatory regime were used to give some hints on the surface chemistry behind the observed dynamics. (author)

Quantum Effects for a Proton in a Low-Barrier, Double-Well Potential: Core Level Photoemission Spectroscopy of Acetylacetone.

Science.gov (United States)

Feyer, Vitaliy; Prince, Kevin C; Coreno, Marcello; Melandri, Sonia; Maris, Assimo; Evangelisti, Luca; Caminati, Walther; Giuliano, Barbara M; Kjaergaard, Henrik G; Carravetta, Vincenzo

2018-02-01

We have performed core level photoemission spectroscopy of gaseous acetylacetone, its fully deuterated form, and two derivatives, benzoylacetone and dibenzoylmethane. These molecules show intramolecular hydrogen bonds, with a proton located in a double-well potential, whose barrier height is different for the three compounds. This has allowed us to examine the effect of the double-well potential on photoemission spectra. Two distinct O 1s core hole peaks are observed, previously assigned to two chemical states of oxygen. We provide an alternative assignment of the double-peak structure of O 1s spectra by taking full account of the extended nature of the wave function associated with the nuclear motion of the proton, the shape of the ground and final state potentials in which the proton is located, and the nonzero temperature of the samples. The peaks are explained in terms of an unusual Franck-Condon factor distribution.

VB Platinum Tile & Carpet, Inc. Information Sheet

Science.gov (United States)

VB Platinum Tile & Carpet, Inc. (the Company) is located in Bristow, Virginia. The settlement involves renovation activities conducted at a property constructed prior to 1978, located in Washington, DC.

Platinum group metal nitrides and carbides: synthesis, properties and simulation

International Nuclear Information System (INIS)

Ivanovskii, Alexander L

2009-01-01

Experimental and theoretical data on new compounds, nitrides and carbides of the platinum group 4d and 5d metals (ruthenium, rhodium, palladium, osmium, iridium, platinum), published over the past five years are summarized. The extreme mechanical properties of platinoid nitrides and carbides, i.e., their high strength and low compressibility, are noted. The prospects of further studies and the scope of application of these compounds are discussed.

Hydroxylamine electrochemistry at low-index single-crystal platinum electrodes in acidic media

NARCIS (Netherlands)

Rosca, V.; Beltramo, G.L.; Koper, M.T.M.

2004-01-01

The electrochemistry of hydroxylamine at low-index single-crystal platinum electrodes in acidic media has been studied by voltammetry and in-situ FTIRRAS. Hydroxylamine (HAM) reactivity at platinum is largely controlled by interaction of the other components of the solution or products of the HAM

Ethanol oxidation on a nichrome-supported spherical platinum microparticle electrocatalyst prepared by electrodeposition

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhen-Hui; Li, Jing; Dong, Xiaoya; Wang, Dong; Chen, Tiwei; Qiao, Haiyan; Huang, Aiping [College of Chemistry and Environmental Science, Henan Key Laboratory for Environmental Pollution Control, Henan Normal University, Jianshe Road, Xinxiang 453007 (China)

2008-11-15

A novel electrode was rapidly prepared by depositing microparticle platinum onto a nichrome substrate in dilute chloroplatinic acid solution by cyclic voltammetry. The SEM results revealed that the deposits were composed of spherical Pt microparticles. Cyclic voltammetry and chronoamperometry were used for the characterization of the electrodes. Results of the electrochemical measurements showed that the spherical Pt microparticle electrodes retained the properties of metal platinum, increased the catalytic activity and promoted the electrocatalytic oxidation of ethanol. Moreover, the deposited Pt microparticles improved the electrochemical properties of the support material and reduced the dosage of noble metal platinum remarkably. The cost could be reduced dramatically by decreasing the contents of platinum. The spherical Pt microparticles deposited on the nichrome supports are likely a potential electrocatalyst for ethanol electrooxidation. (author)

Platinum-bearing chromite layers are caused by pressure reduction during magma ascent.

Science.gov (United States)

Latypov, Rais; Costin, Gelu; Chistyakova, Sofya; Hunt, Emma J; Mukherjee, Ria; Naldrett, Tony

2018-01-31

Platinum-bearing chromitites in mafic-ultramafic intrusions such as the Bushveld Complex are key repositories of strategically important metals for human society. Basaltic melts saturated in chromite alone are crucial to their generation, but the origin of such melts is controversial. One concept holds that they are produced by processes operating within the magma chamber, whereas another argues that melts entering the chamber were already saturated in chromite. Here we address the problem by examining the pressure-related changes in the topology of a Mg 2 SiO 4 -CaAl 2 Si 2 O 8 -SiO 2 -MgCr 2 O 4 quaternary system and by thermodynamic modelling of crystallisation sequences of basaltic melts at 1-10 kbar pressures. We show that basaltic melts located adjacent to a so-called chromite topological trough in deep-seated reservoirs become saturated in chromite alone upon their ascent towards the Earth's surface and subsequent cooling in shallow-level chambers. Large volumes of these chromite-only-saturated melts replenishing these chambers are responsible for monomineralic layers of massive chromitites with associated platinum-group elements.

Structural superlubricity of platinum on graphite under ambient conditions: The effects of chemistry and geometry

Science.gov (United States)

Özoǧul, Alper; Ipek, Semran; Durgun, Engin; Baykara, Mehmet Z.

2017-11-01

An investigation of the frictional behavior of platinum nanoparticles laterally manipulated on graphite has been conducted to answer the question of whether the recent observation of structural superlubricity under ambient conditions [E. Cihan, S. İpek, E. Durgun, and M. Z. Baykara, Nat. Commun. 7, 12055 (2016)] is exclusively limited to the gold-graphite interface. Platinum nanoparticles have been prepared by e-beam evaporation of a thin film of platinum on graphite, followed by post-deposition annealing. Morphological and structural characterization of the nanoparticles has been performed via scanning electron microscopy and transmission electron microscopy, revealing a crystalline structure with no evidence of oxidation under ambient conditions. Lateral manipulation experiments have been performed via atomic force microscopy under ambient conditions, whereby results indicate the occurrence of structural superlubricity at mesoscopic interfaces of 4000-75 000 nm2, with a noticeably higher magnitude of friction forces when compared with gold nanoparticles of similar contact areas situated on graphite. Ab initio simulations of sliding involving platinum and gold slabs on graphite confirm the experimental observations, whereby the higher magnitude of friction forces is attributed to stronger energy barriers encountered by platinum atoms sliding on graphite, when compared with gold. On the other hand, as predicted by theory, the scaling power between friction force and contact size is found to be independent of the chemical identity of the sliding atoms, but to be determined by the geometric qualities of the interface, as characterized by an average "sharpness score" assigned to the nanoparticles.

Poly(3,3-dibenzyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine/Platinum Composite Films as Potential Counter Electrodes for Dye-Sensitized Solar Cells

Directory of Open Access Journals (Sweden)

Jung-Chuan Chou

2017-07-01

Full Text Available In this study, poly(3,3-dibenzyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine/platinum composite films (PProDOT-Bz2/Pt were used as counter electrodes (CEs in dye-sensitized solar cells (DSSCs. The composite films were prepared on fluorine-doped tin oxide (FTO glass by radio frequency (RF sputtering to deposit platinum (Pt for 30 s. Afterwards, PProDOT-Bz2 was deposited on the Pt–FTO glass via electrochemical polymerization. The electron transfer process of DSSCs was investigated using electrochemical impedance spectroscopy (EIS and cyclic voltammetry (CV. The DSSCs with 0.05 C/cm2 PProDOT-Bz2-Pt composite films showed an open circuit voltage (Voc of 0.70 V, a short-circuit current density (Jsc of 7.27 mA/cm2, and a fill factor (F.F. of 68.74%. This corresponded to a photovoltaic conversion efficiency (η of 3.50% under a light intensity of 100 mW/cm2.

Fabrication of three-dimensional platinum microstructures with laser irradiation and electrochemical technique

International Nuclear Information System (INIS)

Kikuchi, T.; Takahashi, H.; Maruko, T.

2007-01-01

Three-dimensional (3D) platinum microstructures were fabricated by successive procedures: aluminum anodizing, laser irradiation, nickel/platinum electroplating, and removal of the aluminum substrate, the oxide films, and the nickel metal layer. Aluminum plates and rods were anodized in an oxalic acid solution to form porous type oxide films. The anodized specimens were immersed in a nickel electroplating solution, and then irradiated with a pulsed Nd-yttrium aluminum garnet (YAG) laser beam to remove the anodic oxide film with a three-dimensional XYZθ stage. The specimens were cathodically polarized in the nickel and a platinum electroplating solution to form the metal micropattern at the laser-irradiated area. The electroplated specimens were immersed in NaOH solution to dissolve the aluminum substrate and the oxide films, and then immersed in HCl solution to dissolve the nickel deposits. A platinum grid-shaped microstructure, a microspring, and a cylindrical network microstructure with 50-100 μm line width were obtained successfully

Fabrication of three-dimensional platinum microstructures with laser irradiation and electrochemical technique

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, T. [Graduate School of Engineering, Hokkaido University, N13, W8, Kita-Ku, Sapporo (Japan)]. E-mail: kiku@elechem1-mc.eng.hokudai.ac.jp; Takahashi, H. [Graduate School of Engineering, Hokkaido University, N13, W8, Kita-Ku, Sapporo (Japan); Maruko, T. [Furuya Metal Co. Ltd., R and D Group, Shimodate Daiichi Kogyodanchi 1915, Morisoejima, Chikusei, Ibaraki (Japan)

2007-02-01

Three-dimensional (3D) platinum microstructures were fabricated by successive procedures: aluminum anodizing, laser irradiation, nickel/platinum electroplating, and removal of the aluminum substrate, the oxide films, and the nickel metal layer. Aluminum plates and rods were anodized in an oxalic acid solution to form porous type oxide films. The anodized specimens were immersed in a nickel electroplating solution, and then irradiated with a pulsed Nd-yttrium aluminum garnet (YAG) laser beam to remove the anodic oxide film with a three-dimensional XYZ{theta} stage. The specimens were cathodically polarized in the nickel and a platinum electroplating solution to form the metal micropattern at the laser-irradiated area. The electroplated specimens were immersed in NaOH solution to dissolve the aluminum substrate and the oxide films, and then immersed in HCl solution to dissolve the nickel deposits. A platinum grid-shaped microstructure, a microspring, and a cylindrical network microstructure with 50-100 {mu}m line width were obtained successfully.

Preparation and Analysis of Platinum Thin Films for High Temperature Sensor Applications

Science.gov (United States)

Wrbanek, John D.; Laster, Kimala L. H.

2005-01-01

A study has been made of platinum thin films for application as high temperature resistive sensors. To support NASA Glenn Research Center s high temperature thin film sensor effort, a magnetron sputtering system was installed recently in the GRC Microsystems Fabrication Clean Room Facility. Several samples of platinum films were prepared using various system parameters to establish run conditions. These films were characterized with the intended application of being used as resistive sensing elements, either for temperature or strain measurement. The resistances of several patterned sensors were monitored to document the effect of changes in parameters of deposition and annealing. The parameters were optimized for uniformity and intrinsic strain. The evaporation of platinum via oxidation during annealing over 900 C was documented, and a model for the process developed. The film adhesion was explored on films annealed to 1000 C with various bondcoats on fused quartz and alumina. From this compiled data, a list of optimal parameters and characteristics determined for patterned platinum thin films is given.

Cis-diamminedichloride platinum II (DDP) in the treatment of penile carcinoma.

Science.gov (United States)

Sklaroff, R B; Yagoda, A

1979-11-01

Cis-diamminedichloride platinum II (DDP) was administered to eight patients with epidermoid carcinoma of the penis. Three of six adequately treated patients had an objective response: one patient achieved complete remission of 7 months duration and 2 patients had partial remissions of 8 and 2 months, respectively. DDP appears to be an active agent in the treatment of penile carcinoma.

Determination of microquantities of silver in platinum by isotope dilution

International Nuclear Information System (INIS)

Yedinakova, V.; Sladkovska, Y.

1980-01-01

A method is described for determining microquantities of silver in platinum. It is based on isotope dilution by means of substoichiometric extraction of dithizonates with carbon tetrachloride. The determination of silver according to this technique is not interfered by zinc or gold in quantities exceeding the silver content by one order of magnitude nor by a great excess of platinum. In the presence of copper the addition of complexon is necessary. (author)

A Meta-Analysis of Platinum Plus Gemcitabine or Vinorelbine for Advanced Non-small Cell Lung Cancer

Directory of Open Access Journals (Sweden)

Guanghui GAO

2009-01-01

Full Text Available Background and objective Platinum plus the third-generation agent doublet chemotherapy is the standard regimens and first line chemotherapy for advanced non-small cell lung cancer (NSCLC. The aim of this study is to determine the benefits and harms of platinum plus gemcitabine or vinorelbine for advanced NSCLC. Methods Thedatabases PubMed, CENTRAL, EMBASE and Chinese Biomedical Literature database were retrieved by using the key words "non small cell lung cancer" or "Carcinoma, Non Small Cell Lung" so as to search the studies about the randomized controlled clinical trials (RCT that had compared the gemcitabine plus platinum versus vinorelbine plus platinum for advanced NSCLC. A meta-analysis was conducted. Results Nine randomized controlled trials, with total 2 186 patients,were included. The overall response rate and one-year survival rate of the gemcitabine group were not significantly different from that of vinorelbine regimen (RR=0.91, 95%CI: 0.81-1.03, P =0.15; RR=1.06, 95%CI: 0.96-1.18, P =0.27, respectively. The incidence rate of grade 3-4 netropenia, constipation, phlebitis and grade 1-4 neuropathy were higher in vinorelbine group, just like higher incidence rate of grade 3-4 thrombocytopenia in the gemcitabine group. Conclusion The curative effects of the gemcitabine or vinorelbine plus platinum regimens are similar. The choice of gemcitabine or vinorelbine depends on the toxicity of the drugs and patients' tolerance.

Origin of the different behavior of some platinum decorated nanocarbons towards the electrochemical oxidation of hydrogen peroxide

Energy Technology Data Exchange (ETDEWEB)

Malara, A. [Dipartimento di Ingegneria dell' Informazione, delle Infrastrutture e dell' Energia Sostenibile (DIIES), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Leonardi, S.G.; Bonavita, A. [Dipartimento di Ingegneria Elettronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Fazio, E. [Dipartimento di Scienze Matematiche e Informatiche, Scienze Fisiche e Scienze della Terra (MIFT), Università di Messina, 98166 Messina (Italy); Stelitano, S. [Dipartimento di Fisica (DF), Università della Calabria, 87036 Arcavacata di Rende (Italy); Neri, G. [Dipartimento di Ingegneria Elettronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Neri, F. [Dipartimento di Scienze Matematiche e Informatiche, Scienze Fisiche e Scienze della Terra (MIFT), Università di Messina, 98166 Messina (Italy); Santangelo, S., E-mail: saveria.santangelo@unirc.it [Dipartimento di Ingegneria Civile, dell' Energia, dell' Ambiente e dei Materiali (DICEAM), Università “Mediterranea”, 89122 Reggio Calabria (Italy)

2016-12-01

The electrochemical behavior of different platinum-decorated nanocarbons (Pt@C) towards the oxidation of hydrogen peroxide (H{sub 2}O{sub 2}) was investigated. Three different types of nanocarbons were considered: i) carbon black, ii) dahlia-like carbon nanohorns and iii) carbon nanotubes, which included both commercial (single-wall and multi-wall) and laboratory prepared (multi-wall) samples. Shape and size distribution of the platinum nanoparticles and morphology of the nanocarbons were analyzed by transmission electron microscopy. Their nanostructure was investigated by micro-Raman spectroscopy, while elemental composition of the samples and chemical bonding states were studied by X-ray photoelectron spectroscopy. Electrochemical behavior towards H{sub 2}O{sub 2} oxidation was evaluated by means of cyclic voltammetry modifying the working screen-printed carbon electrode surface with the prepared Pt@C nanocomposites. Data obtained suggest that the size and dispersion of the Pt nanoparticles play a key role in increasing the sensitivity towards H{sub 2}O{sub 2} detection. Thanks to the presence of smaller and more dispersed platinum particles and of a greater amount of platinum hydroxide, acting as intermediary in the H{sub 2}O{sub 2} oxidation process, Pt@dahlia-like carbon nanohorns result to be the most promising platform for the development of H{sub 2}O{sub 2} electrochemical sensors. - Highlights: • Different nanocarbons are decorated with Pt nanoparticles by wet impregnation method. • Pt@C-based hybrids are tested as active materials for sensing of hydrogen peroxide. • Sensor based on Pt@dahlia-like carbon nanohorns is the most performing device. • The origin of the different electrochemical behaviour is investigated. • Pt@C sensing performances are correlated with their structural and surface properties.

A sensitive electrochemical aptasensor based on the co-catalysis of hemin/G-quadruplex, platinum nanoparticles and flower-like MnO2 nanosphere functionalized multi-walled carbon nanotubes.

Science.gov (United States)

Xu, Wenju; Xue, Shuyan; Yi, Huayu; Jing, Pei; Chai, Yaqin; Yuan, Ruo

2015-01-28

In this work, a sensitive electrochemical aptasensor for the detection of thrombin (TB) is developed and demonstrated based on the co-catalysis of hemin/G-quadruplex, platinum nanoparticles (PtNPs) and flower-like MnO2 nanosphere functionalized multi-walled carbon nanotubes (MWCNT-MnO2).

Melting behaviour of gold-platinum nanoalloy clusters by molecular dynamics simulations

Energy Technology Data Exchange (ETDEWEB)

Ong, Yee Pin; Yoon, Tiem Leong [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lim, Thong Leng [Faculty of Engineering and Technology, Multimedia University, Melaka Campus, 75450 Melaka (Malaysia)

2015-04-24

The melting behavior of bimetallic gold-platinum nanoclusters is studied by applying Brownian-type isothermal molecular dynamics (MD) simulation, a program modified from the cubic coupling scheme (CCS). The process begins with the ground-state structures obtained from global minimum search algorithm and proceeds with the investigation of the effect of temperature on the thermal properties of gold-platinum nanoalloy clusters. N-body Gupta potential has been employed in order to account for the interactions between gold and platinum atoms. The ground states of the nanoalloy clusters, which are core-shell segregated, are heated until they become thermally segregated. The detailed melting mechanism of the nanoalloy clusters is studied via this approach to provide insight into the thermal stability of the nanoalloy clusters.

Iron-Mediated Homogeneous ICAR ATRP of Methyl Methacrylate under ppm Level Organometallic Catalyst Iron(III Acetylacetonate

Directory of Open Access Journals (Sweden)

Jian Wu

2016-01-01

Full Text Available Atom Transfer Radical Polymerization (ATRP is an important polymerization process in polymer synthesis. However, a typical ATRP system has some drawbacks. For example, it needs a large amount of transition metal catalyst, and it is difficult or expensive to remove the metal catalyst residue in products. In order to reduce the amount of catalyst and considering good biocompatibility and low toxicity of the iron catalyst, in this work, we developed a homogeneous polymerization system of initiators for continuous activator regeneration ATRP (ICAR ATRP with just a ppm level of iron catalyst. Herein, we used oil-soluble iron (III acetylacetonate (Fe(acac3 as the organometallic catalyst, 1,1′-azobis (cyclohexanecarbonitrile (ACHN with longer half-life period as the thermal initiator, ethyl 2-bromophenylacetate (EBPA as the initiator, triphenylphosphine (PPh3 as the ligand, toluene as the solvent and methyl methacrylate (MMA as the model monomer. The factors related with the polymerization system, such as concentration of Fe(acac3 and ACHN and polymerization kinetics, were investigated in detail at 90 °C. It was found that a polymer with an acceptable molecular weight distribution (Mw/Mn = 1.43 at 45.9% of monomer conversion could be obtained even with 1 ppm of Fe(acac3, making it needless to remove the residual metal in the resultant polymers, which makes such an ICAR ATRP process much more industrially attractive. The “living” features of this polymerization system were further confirmed by chain-extension experiment.

Sculptured platinum nanowire counter electrodes for dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyeonseok [Department of Electrical Engineering, Pennsylvania State University, University Park 16802 (United States); Horn, Mark W., E-mail: MHorn@engr.psu.edu [Department of Engineering Science and Mechanics, Pennsylvania State University, University Park 16802-6812 (United States)

2013-07-01

Sculptured platinum nanowire thin films were formed by oblique angle electron beam evaporation with a 5° vapor incidence angle and incorporated as counter electrodes for dye-sensitized solar cells (DSSCs). For the comparison of the performance, bare fluorine doped tin oxide, planar Pt electrodes and counter electrodes treated with chloroplatinic acid were prepared. The sculptured Pt nanowire electrodes showed five times lower charge transfer resistance (0.121 [Ω∗cm{sup 2}]) than that of Pt planar electrode (0.578 [Ω∗cm{sup 2}]) and when the Pt nanowire electrodes are treated with an H{sub 2}PtCl{sub 6} solution have more than ten times lower charge transfer resistance (0.04025 [Ω∗cm{sup 2}]). Moreover, Pt nanowire films used as a counter electrode lead to enhancement in current density and efficiency in comparison with Pt planar counter electrodes. The conversion efficiency with planar electrodes was 5.1 [%] while the efficiency of DSSC with platinum nanowire counter electrodes reached to 5.63 [%] under AM 1.5 illumination. - Highlights: • Pt sculptured thin films (STFs) fabricated by electron beam evaporator. • The STFs featured higher roughness and lower charge transfer resistance. • Improved performance of dye-sensitized solar cells by Pt STFs counter electrodes.

The association between COX-2 polymorphisms and hematologic toxicity in patients with advanced non-small-cell lung cancer treated with platinum-based chemotherapy.

Directory of Open Access Journals (Sweden)

Fei Zhou

Full Text Available BACKGROUND AND OBJECTIVE: Overexpression of COX-2 is proved to contribute to tumor promotion and carcinogenesis through stimulating cell proliferation, inhibiting apoptosis and enhancing the invasiveness of cancer cells. Apoptosis-related molecules are potential predictive markers for survival and toxicity in platinum treatment. This study aimed at investigating the association between COX-2 polymorphisms and the occurrence of grade 3 or 4 toxicity in advanced non-small cell lung cancer patients treated with platinum-based chemotherapy. MATERIALS AND METHODS: Two hundred and twelve patients with inoperable stage IIIB-IV NSCLC received first-line chemotherapy between 2007 and 2009 were recruited in this study. Four functional COX-2 polymorphisms were genotyped by PCR-based restriction fragment length polymorphism (RFLP methods. RESULTS: The incidence of grade 3 or 4 hematologic toxicity was significantly higher in G allele carriers of the COX-2 rs689466 (-1195G/A polymorphism compared with wild-type homozygotes AA (P value = 0.008; odds ratio, 2.47; 95% confidence internal, 1.26-4.84 and the significance still existed after the Bonferroni correction. Statistically significant difference was also found in grade 3 or 4 leukopenia (P value = 0.010; OR = 2.82; 95%CI = 1.28-6.20. No other significant association was observed between genotype and toxicity in the study. The haplotype analysis showed that the haplotype AGG was associated with a reduced risk of grade 3 or 4 hematologic and leukopenia toxicity (P value = 0.009; OR = 0.59; 95%CI = 0.39-0.88 and P value = 0.025; OR = 0.61; 95%CI = 0.39-0.94, respectively while the haplotype GGG was associated with an increased risk of grade 3 or 4 hematologic and leukopenia toxicity (P value = 0.009; OR = 1.71; 95%CI = 1.14-2.56 and P value = 0.025; OR = 1.65; 95%CI  = 1.06-2.57, respectively. CONCLUSION: This investigation for the first time

Reaction of ethane with deuterium over platinum(111) single-crystal surfaces

International Nuclear Information System (INIS)

Zaera, F.; Somorhai, G.A.

1985-01-01

Deuterium exchange and hydrogenolysis of ethane were studied over (111) platinum surfaces under atmospheric pressures and a temperature range of 475-625 K. Activation energies of 19 kcal/mol for exchange and 34 kcal/mol for hydrogenolysis were obtained. The exchange reaction rates displayed kinetic orders with respect to deuterium and ethane partial pressures of -0.55 and 1.2, respectively. The exchange production distribution was U-shaped, peaking at one and six deuterium atoms per ethane molecule, similar to results reported for other forms of platinum, e.g., supported, films, and foils. The pressure of ethylidyne moieties on the surface was inferred from low-energy electron diffraction and thermal desorption spectroscopy. A mechanism is proposed to explain the experimental results, in which ethylidyne constitutes an intermediate in one of two competitive pathways. 31 references, 9 figures, 3 tables

Permeation of platinum and rhodium nanoparticles through intact and damaged human skin

International Nuclear Information System (INIS)

Mauro, Marcella; Crosera, Matteo; Bianco, Carlotta; Adami, Gianpiero; Montini, Tiziano; Fornasiero, Paolo; Jaganjac, Morana; Bovenzi, Massimo; Filon, Francesca Larese

2015-01-01

The aim of the study was to evaluate percutaneous penetration of platinum and rhodium nanoparticles (PtNPs: 5.8 ± 0.9 nm, RhNPs: 5.3 ± 1.9 nm) through human skin. Salts compounds of these metals are sensitizers and some also carcinogenic agents. In vitro permeation experiments were performed using Franz diffusion cells with intact and damaged skin. PtNPs and RhNPs, stabilized with polyvinylpyrrolidone, were synthesized by reduction of Na 2 PtC l6 and RhCl 3 ·3H 2 O respectively. Suspensions with a concentration of 2.0 g/L of PtNPs and RhNPs were dispersed separately in synthetic sweat at pH 4.5 and applied as donor phases to the outer surface of the skin for 24 h. Measurements of the content of the metals in the receiving solution and in the skin were performed subsequently. Rhodium skin permeation was demonstrated through damaged skin, with a permeation flux of 0.04 ± 0.04 μg cm −2  h −1 and a lag time of 7.9 ± 1.1 h, while no traces of platinum were found in receiving solutions. Platinum and rhodium skin-analysis showed significantly higher concentrations of the metals in damaged skin. Rh and Pt applied as NPs can penetrate the skin barrier and Rh can be found in receiving solutions. These experiments pointed out the need for skin contamination prevention, since even a minor injury to the skin barrier can significantly increase penetration

Permeation of platinum and rhodium nanoparticles through intact and damaged human skin

Energy Technology Data Exchange (ETDEWEB)

Mauro, Marcella [University of Trieste, Clinical Unit of Occupational Medicine, Department of Medical Sciences (Italy); Crosera, Matteo; Bianco, Carlotta; Adami, Gianpiero; Montini, Tiziano; Fornasiero, Paolo [University of Trieste, Department of Chemical and Pharmaceutical Sciences (Italy); Jaganjac, Morana [Rudjer Boskovic Institute, Laboratory for Oxidative Stress, Department of Molecular Medicine (Croatia); Bovenzi, Massimo; Filon, Francesca Larese, E-mail: larese@units.it [University of Trieste, Clinical Unit of Occupational Medicine, Department of Medical Sciences (Italy)

2015-06-15

The aim of the study was to evaluate percutaneous penetration of platinum and rhodium nanoparticles (PtNPs: 5.8 ± 0.9 nm, RhNPs: 5.3 ± 1.9 nm) through human skin. Salts compounds of these metals are sensitizers and some also carcinogenic agents. In vitro permeation experiments were performed using Franz diffusion cells with intact and damaged skin. PtNPs and RhNPs, stabilized with polyvinylpyrrolidone, were synthesized by reduction of Na{sub 2}PtC{sub l6} and RhCl{sub 3}·3H{sub 2}O respectively. Suspensions with a concentration of 2.0 g/L of PtNPs and RhNPs were dispersed separately in synthetic sweat at pH 4.5 and applied as donor phases to the outer surface of the skin for 24 h. Measurements of the content of the metals in the receiving solution and in the skin were performed subsequently. Rhodium skin permeation was demonstrated through damaged skin, with a permeation flux of 0.04 ± 0.04 μg cm{sup −2} h{sup −1} and a lag time of 7.9 ± 1.1 h, while no traces of platinum were found in receiving solutions. Platinum and rhodium skin-analysis showed significantly higher concentrations of the metals in damaged skin. Rh and Pt applied as NPs can penetrate the skin barrier and Rh can be found in receiving solutions. These experiments pointed out the need for skin contamination prevention, since even a minor injury to the skin barrier can significantly increase penetration.

Platinum clusters with precise numbers of atoms for preparative-scale catalysis.

Science.gov (United States)

Imaoka, Takane; Akanuma, Yuki; Haruta, Naoki; Tsuchiya, Shogo; Ishihara, Kentaro; Okayasu, Takeshi; Chun, Wang-Jae; Takahashi, Masaki; Yamamoto, Kimihisa

2017-09-25

Subnanometer noble metal clusters have enormous potential, mainly for catalytic applications. Because a difference of only one atom may cause significant changes in their reactivity, a preparation method with atomic-level precision is essential. Although such a precision with enough scalability has been achieved by gas-phase synthesis, large-scale preparation is still at the frontier, hampering practical applications. We now show the atom-precise and fully scalable synthesis of platinum clusters on a milligram scale from tiara-like platinum complexes with various ring numbers (n = 5-13). Low-temperature calcination of the complexes on a carbon support under hydrogen stream affords monodispersed platinum clusters, whose atomicity is equivalent to that of the precursor complex. One of the clusters (Pt 10 ) exhibits high catalytic activity in the hydrogenation of styrene compared to that of the other clusters. This method opens an avenue for the application of these clusters to preparative-scale catalysis.The catalytic activity of a noble metal nanocluster is tied to its atomicity. Here, the authors report an atom-precise, fully scalable synthesis of platinum clusters from molecular ring precursors, and show that a variation of only one atom can dramatically change a cluster's reactivity.

Fluoropyrimidine and platinum toxicity pharmacogenetics: an umbrella review of systematic reviews and meta-analyses.

Science.gov (United States)

Campbell, Jared M; Bateman, Emma; Peters, Micah Dj; Bowen, Joanne M; Keefe, Dorothy M; Stephenson, Matthew D

2016-03-01

Fluoropyrimidine (FU) and platinum-based chemotherapies are greatly complicated by their associated toxicities. This umbrella systematic review synthesized all systematic reviews that investigated associations between germline variations and toxicity, with the aim of informing personalized medicine. Systematic reviews are important in pharmacogenetics where false positives are common. Four systematic reviews were identified for FU-induced toxicity and three for platinum. Polymorphisms of DPYD and TYMS, but not MTHFR, were statistically significantly associated with FU-induced toxicity (although only DPYD had clinical significance). For platinum, GSTP1 was found to not be associated with toxicity. This umbrella systematic review has synthesized the best available evidence on the pharmacogenetics of FU and platinum toxicity. It provides a useful reference for clinicians and identifies important research gaps.

Catalytic wet oxidation of ammonia solution: Activity of the nanoscale platinum-palladium-rhodium composite oxide catalyst

International Nuclear Information System (INIS)

Hung, C.-M.

2009-01-01

Aqueous solutions of 400-1000 mg/L of ammonia were oxidized in a trickle-bed reactor (TBR) in this study of nanoscale platinum-palladium-rhodium composite oxide catalysts, which were prepared by the co-precipitation of H 2 PtCl 6 , Pd(NO 3 ) 3 and Rh(NO 3 ) 3 . Hardly any of the dissolved ammonia was removed by wet oxidation in the absence of any catalyst, whereas about 99% of the ammonia was reduced during wet oxidation over nanoscale platinum-palladium-rhodium composite oxide catalysts at 503 K in an oxygen partial pressure of 2.0 MPa. A synergistic effect exists in the nanoscale platinum-palladium-rhodium composite structure, which is the material with the highest ammonia reduction activity. The nanometer-sized particles were characterized by TEM, XRD and FTIR. The effect of the initial concentration and reaction temperature on the removal of ammonia from the effluent streams was also studied at a liquid hourly space velocity of under 9 h -1 in the wet catalytic processes

Catalytic wet oxidation of ammonia solution: Activity of the nanoscale platinum-palladium-rhodium composite oxide catalyst

Energy Technology Data Exchange (ETDEWEB)

Hung, C.-M. [Department of Industry Engineering and Management, Yung-Ta Institute of Technology and Commerce, 316 Chung-shan Road, Linlo, Pingtung 909, Taiwan (China)], E-mail: hungcm1031@gmail.com

2009-04-15

Aqueous solutions of 400-1000 mg/L of ammonia were oxidized in a trickle-bed reactor (TBR) in this study of nanoscale platinum-palladium-rhodium composite oxide catalysts, which were prepared by the co-precipitation of H{sub 2}PtCl{sub 6}, Pd(NO{sub 3}){sub 3} and Rh(NO{sub 3}){sub 3}. Hardly any of the dissolved ammonia was removed by wet oxidation in the absence of any catalyst, whereas about 99% of the ammonia was reduced during wet oxidation over nanoscale platinum-palladium-rhodium composite oxide catalysts at 503 K in an oxygen partial pressure of 2.0 MPa. A synergistic effect exists in the nanoscale platinum-palladium-rhodium composite structure, which is the material with the highest ammonia reduction activity. The nanometer-sized particles were characterized by TEM, XRD and FTIR. The effect of the initial concentration and reaction temperature on the removal of ammonia from the effluent streams was also studied at a liquid hourly space velocity of under 9 h{sup -1} in the wet catalytic processes.

Catalytic wet oxidation of ammonia solution: activity of the nanoscale platinum-palladium-rhodium composite oxide catalyst.

Science.gov (United States)

Hung, Chang-Mao

2009-04-15

Aqueous solutions of 400-1000 mg/L of ammonia were oxidized in a trickle-bed reactor (TBR) in this study of nanoscale platinum-palladium-rhodium composite oxide catalysts, which were prepared by the co-precipitation of H(2)PtCl(6), Pd(NO(3))(3) and Rh(NO(3))(3). Hardly any of the dissolved ammonia was removed by wet oxidation in the absence of any catalyst, whereas about 99% of the ammonia was reduced during wet oxidation over nanoscale platinum-palladium-rhodium composite oxide catalysts at 503 K in an oxygen partial pressure of 2.0 MPa. A synergistic effect exists in the nanoscale platinum-palladium-rhodium composite structure, which is the material with the highest ammonia reduction activity. The nanometer-sized particles were characterized by TEM, XRD and FTIR. The effect of the initial concentration and reaction temperature on the removal of ammonia from the effluent streams was also studied at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes.

Synthesis, structure, theoretical studies and luminescent properties of a ternary erbium(III) complex with acetylacetone and bathophenanthroline ligands

Energy Technology Data Exchange (ETDEWEB)

Martín-Ramos, Pablo [CEMDRX, Department of Physics, Universidade de Coimbra, Rua Larga, P-3004-516 Coimbra (Portugal); Advanced Materials Laboratory, ETSIIAA, Universidad de Valladolid, Avenida de Madrid 44, 34004 Palencia (Spain); Silva, Pedro S. Pereira, E-mail: psidonio@pollux.fis.uc.pt [CEMDRX, Department of Physics, Universidade de Coimbra, Rua Larga, P-3004-516 Coimbra (Portugal); Chamorro-Posada, Pedro [Higher Technical School of Telecommunications Engineering, Universidad de Valladolid, Campus Miguel Delibes, Paseo Belén 15, 47011 Valladolid (Spain); Silva, Manuela Ramos [CEMDRX, Department of Physics, Universidade de Coimbra, Rua Larga, P-3004-516 Coimbra (Portugal); Milne, Bruce F. [Centre for Computational Physics, Department of Physics, Universidade de Coimbra, P-3004-516 Coimbra (Portugal); Donostia International Physics Centre, Paseo Manuel de Lardizabal 4, 20018 Donostia-San Sebastián (Spain); Nogueira, Fernando [Centre for Computational Physics, Department of Physics, Universidade de Coimbra, P-3004-516 Coimbra (Portugal); Martín-Gil, Jesús [Advanced Materials Laboratory, ETSIIAA, Universidad de Valladolid, Avenida de Madrid 44, 34004 Palencia (Spain)

2015-06-15

A novel erbium(III) complex with acetylacetone (Hacac) and bathophenanthroline (4,7-diphenyl-1,10-phenanthroline, bath) ligands, formulated as [Er(acac){sub 3}(bath)], has been characterized by elemental analysis, X-ray diffraction, thermogravimetric analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, absorption and emission spectroscopies. In the theoretical part of this study, semi-empirical quantum chemistry methods using AM1, PM3, PM6 and PM7 models have been employed to predict the structure of the complex, calculate the geometric and crystallographic parameters, and make comparisons with spectroscopic data using INDO/S-CI calculations. Real-time time-dependent density-functional theory (TDDFT) has also been used to calculate the optical absorption spectrum of the complex in the gas phase. - Highlights: • Synthesis and structure of a new erbium(III) β-diketonate complex. • TDDFT used for the first time to calculate the optical absorption spectrum. • Complex show strong near-infrared luminescence at 1.53 µm due to antenna effect.

Synthesis, structure, theoretical studies and luminescent properties of a ternary erbium(III) complex with acetylacetone and bathophenanthroline ligands

International Nuclear Information System (INIS)

Martín-Ramos, Pablo; Silva, Pedro S. Pereira; Chamorro-Posada, Pedro; Silva, Manuela Ramos; Milne, Bruce F.; Nogueira, Fernando; Martín-Gil, Jesús

2015-01-01

A novel erbium(III) complex with acetylacetone (Hacac) and bathophenanthroline (4,7-diphenyl-1,10-phenanthroline, bath) ligands, formulated as [Er(acac) 3 (bath)], has been characterized by elemental analysis, X-ray diffraction, thermogravimetric analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, absorption and emission spectroscopies. In the theoretical part of this study, semi-empirical quantum chemistry methods using AM1, PM3, PM6 and PM7 models have been employed to predict the structure of the complex, calculate the geometric and crystallographic parameters, and make comparisons with spectroscopic data using INDO/S-CI calculations. Real-time time-dependent density-functional theory (TDDFT) has also been used to calculate the optical absorption spectrum of the complex in the gas phase. - Highlights: • Synthesis and structure of a new erbium(III) β-diketonate complex. • TDDFT used for the first time to calculate the optical absorption spectrum. • Complex show strong near-infrared luminescence at 1.53 µm due to antenna effect

Prediction of ligand effects in platinum-amyloid-β coordination.

Science.gov (United States)

Turner, Matthew; Deeth, Robert J; Platts, James A

2017-08-01

Ligand field molecular mechanics (LFMM) and semi-empirical Parametric Model 7 (PM7) methods are applied to a series of six Pt II -Ligand systems binding to the N-terminal domain of the amyloid-β (Aβ) peptide. Molecular dynamics using a combined LFMM/Assisted Model Building with Energy Refinement (AMBER) approach is used to explore the conformational freedom of the peptide fragment, and identifies favourable platinum binding modes and peptide conformations for each ligand investigated. Platinum coordination is found to depend on the nature of the ligand, providing evidence that binding mode may be controlled by suitable ligand design. Boltzmann populations at 310K indicate that each Pt-Aβ complex has a small number of thermodynamically accessible states. Ramachandran maps are constructed for the sampled Pt-Aβ conformations and secondary structural analysis of the obtained complex structures is performed and contrasted with the free peptide; coordination of these platinum complexes disrupts existing secondary structure in the Aβ peptide and promotes formation of ligand-specific turn-type secondary structure. Copyright © 2017 Elsevier Inc. All rights reserved.

Clinical development of platinum complexes in cancer therapy: an historical perspective and an update.

Science.gov (United States)

Lebwohl, D; Canetta, R

1998-09-01

The vast amount of basic research on platinum coordination complexes has produced, over the past 25 years, several thousand new molecules for preclinical screening and 28 compounds which have entered clinical development. The goals of these research activities have been to identify compounds with superior efficacy, reduced toxicity, lack of cross-resistance or improved pharmacological characteristics as compared with the parent compound, cisplatin. After the remarkable therapeutic effects of cisplatin had been established, only a few other platinum compounds succeeded in reaching general availability. Whereas carboplatin is an analogue with an improved therapeutic index (mostly driven by reduced organ toxicity) over that of cisplatin, new compounds clearly more active than or non-cross-resistant with cisplatin have not yet been identified. The platinum analogues that remain under investigation are focusing on expanding the utilisation of platinum therapy to tumour types not usually treated with, or responsive to, cisplatin or carboplatin. In addition, novel routes of administration constitute another avenue of research. The clinical development of platinum coordination complexes, with emphasis on those compounds still under active development, is reviewed.

The stability of PEMFC electrodes : platinum dissolution vs potential and temperature investigated by quartz crystal microbalance

NARCIS (Netherlands)

Dam, V.A.T.; Bruijn, de F.A.

2007-01-01

The stability of platinum in proton exchange membrane fuel cell (PEMFC) electrodes has been investigated by determining the dissolution of platinum from a thin platinum film deposited on a gold substrate in 1 M HClO4 at different temperatures ranging between 40 and 80°C and potentials between 0.85

Responses of fibroblasts and glial cells to nanostructured platinum surfaces

Energy Technology Data Exchange (ETDEWEB)

Pennisi, C P; Sevcencu, C; Yoshida, K [Center for Sensory-Motor Interaction (SMI), Aalborg University, Aalborg (Denmark); Dolatshahi-Pirouz, A; Foss, M; Larsen, A Nylandsted; Besenbacher, F [Interdisciplinary Nanoscience Center (iNANO), Aarhus University, Aarhus (Denmark); Hansen, J Lundsgaard [Department of Physics and Astronomy, Aarhus University, Aarhus (Denmark); Zachar, V, E-mail: cpennisi@hst.aau.d [Laboratory for Stem Cell Research, Aalborg University (Denmark)

2009-09-23

The chronic performance of implantable neural prostheses is affected by the growth of encapsulation tissue onto the stimulation electrodes. Encapsulation is associated with activation of connective tissue cells at the electrode's metallic contacts, usually made of platinum. Since surface nanotopography can modulate the cellular responses to materials, the aim of the present work was to evaluate the 'in vitro' responses of connective tissue cells to platinum strictly by modulating its surface nanoroughness. Using molecular beam epitaxy combined with sputtering, we produced platinum nanostructured substrates consisting of irregularly distributed nanopyramids and investigated their effect on the proliferation, cytoskeletal organization and cellular morphology of primary fibroblasts and transformed glial cells. Cells were cultured on these substrates and their responses to surface roughness were studied. After one day in culture, the fibroblasts were more elongated and their cytoskeleton less mature when cultured on rough substrates. This effect increased as the roughness of the surface increased and was associated with reduced cell proliferation throughout the observation period (4 days). Morphological changes also occurred in glial cells, but they were triggered by a different roughness scale and did not affect cellular proliferation. In conclusion, surface nanotopography modulates the responses of fibroblasts and glial cells to platinum, which may be an important factor in optimizing the tissue response to implanted neural electrodes.

Amperometric and coulometric methods of platinum metal determination. (Review)

International Nuclear Information System (INIS)

Ezerskaya, N.A.

1981-01-01

Reviewed are works published in the period from 1957-1979, on amperometric and coulometric (potentiostatistic and amperostatistic variant) determination of platinum metals, Ru in particular. During amperometric titration of Ru the following titrantes are used: hydroquinone, thioxne thiourea, Na 2 S 2 O 3 . It is proposed to titrate Ru in the form of ruthenate-ion with hydrazine sulphate in alkal: medium according to the current of reagent oxidation. During coulometric determination of Ru the electrogenerating titrant TiCl 3 or Ti 2 (SO 4 ) 3 (for initial form of Ru [RuCl 6 ] 2- ) is used [ru

1.7 nm Platinum Nanoparticles: Synthesis with Glucose Starch, Characterization and Catalysis

DEFF Research Database (Denmark)

Engelbrekt, Christian; Sørensen, Karsten Holm; Lubcke, T.

2010-01-01

Monodisperse platinum nanoparticles (PtNPs) were synthesized by a green recipe. Glucose serves as a reducing agent and starch as a stabilization agent to protect the freshly formed PtNP cores in buffered aqueous solutions. Among the ten buffers studied, 2-(N-morpholino)ethanesulfonic acid (MES), ...

Effect of the geometry of the central coordination sphere in antitumor trinuclear platinum complexes on DNA binding

Czech Academy of Sciences Publication Activity Database

Kašpárková, Jana; Vrána, Oldřich; Farrell, N.; Brabec, Viktor

2004-01-01

Roč. 98, č. 10 (2004), s. 1560-1569 ISSN 0162-0134. [International Symposium on Platinum Compounds in Cancer Chemotherapy /9./. New York, 08.10.2004-11.10.2004] R&D Projects: GA ČR GA305/02/1552; GA AV ČR KJB5004301; GA AV ČR IBS5004009 Grant - others:National Institutes of Health(US) CA-78754 Institutional research plan: CEZ:AV0Z5004920 Keywords : DNA * platinum * antitumor Subject RIV: BO - Biophysics Impact factor: 2.225, year: 2004

A phenyl-sulfonic acid anchored carbon-supported platinum catalyst for polymer electrolyte fuel cell electrodes

International Nuclear Information System (INIS)

Selvarani, G.; Sahu, A.K.; Choudhury, N.A.; Sridhar, P.; Pitchumani, S.; Shukla, A.K.

2007-01-01

A method, to anchor phenyl-sulfonic acid functional groups with the platinum catalyst supported onto a high surface-area carbon substrate, is reported. The use of the catalyst in the electrodes of a polymer electrolyte fuel cell (PEFC) helps enhancing its performance. Characterization of the catalyst by Fourier transform infra red (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and point-of-zero-charge (PZC) studies suggests that the improvement in performance of the PEFC is facilitated not only by enlarging the three-phase boundary in the catalyst layer but also by providing ionic-conduction paths as well as by imparting negative charge to platinum sites with concomitant oxidation of sulfur present in the carbon support. It is argued that the negatively charged platinum sites help repel water facilitating oxygen to access the catalyst sites. The PEFC with modified carbon-supported platinum catalyst electrodes exhibits 40% enhancement in its power density as compared to the one with unmodified carbon-supported platinum catalyst electrodes

Investigation of mechanical and structural characteristics of platinum and palladium at high temperatures

Energy Technology Data Exchange (ETDEWEB)

Trumie, B. T.; Gomidzelovie, L.; Marjanovic, S. R.; Krstic, V. R.

2015-03-30

In order to broaden future application of products based on platinum and palladium a comparative analysis of their high-temperature mechanical properties was performed. Platinum and palladium are of great importance and are widely used in chemical industry, electronics, for making laboratory dishes, to name a few. Mechanical properties of pure metals, such as: tensile strength, creep rate and rupture time were investigated using universal testing machine for tensile testing of materials. Microstructure of samples was investigated by optical microscopy. Based on obtained results it can be concluded that the platinum, compared to palladium, is superior for high-temperature applications. (Author)

Investigation of mechanical and structural characteristics of platinum and palladium at high temperatures

International Nuclear Information System (INIS)

Trumie, B. T.; Gomidzelovie, L.; Marjanovic, S. R.; Krstic, V. R.

2015-01-01

In order to broaden future application of products based on platinum and palladium a comparative analysis of their high-temperature mechanical properties was performed. Platinum and palladium are of great importance and are widely used in chemical industry, electronics, for making laboratory dishes, to name a few. Mechanical properties of pure metals, such as: tensile strength, creep rate and rupture time were investigated using universal testing machine for tensile testing of materials. Microstructure of samples was investigated by optical microscopy. Based on obtained results it can be concluded that the platinum, compared to palladium, is superior for high-temperature applications. (Author)

PEEM microscopy and DFT calculations of catalytically active platinum surfaces and interfaces

International Nuclear Information System (INIS)

Spiel, C.

2012-01-01

The aim of this thesis was to investigate the properties of catalytically active platinum surfaces and interfaces both with experimental and theoretical methods. Using experimental methods, catalytic CO oxidation on individual grains of a polycrystalline platinum foil was studied in situ under high vacuum (HV) conditions. A polycrystalline platinum foil consists of individual µm-sized crystal grains that are mainly [100]-, [110]- and [111]-oriented and differ significantly in their catalytic activity. In order to elucidate the differences existing between the reactivity of the individual grains, a combination of photoemission electron microscopy (PEEM) and quadrupole mass spectrometry (QMS) was used in this work. The working principle of PEEM is based on the photoelectric effect where illumination of the sample with (UV-)light causes emission of photoelectrons. The emitted photoelectrons are used to visualize the sample surface (with typical resolution in the low micrometer range). The PEEM image contrast originates from differences in the local work function that may arise due to different crystallographic orientations and/or changes in the adsorbate coverage. With a combination of PEEM and QMS, it was possible to study the kinetics of catalytic CO oxidation on polycrystalline platinum foil both in a global and a laterally-resolved way simultaneously. If catalytic CO oxidation on surfaces of platinum is followed at constant temperature and oxygen partial pressure under cyclic variation of the CO pressure, a hysteresis in the CO2 production rate is observed in the bistability region with two noticeable kinetic transitions (called tA and tB) taking place at different CO pressures when the catalyst surface switches back-and-forth between two steady states of high and low reactivity while the Pt-surface is, correspondingly, either oxygen- or CO-covered. In the bistability region between τ A and τ B , the system stays (at the same values of the external parameters p

A comparative study of roles played by aluminum tribromide and aluminum acetylacetonate on the thermal degradation of PMMA by simultaneous thermoanalytical techniques

International Nuclear Information System (INIS)

Arshad, M.; Arif, M.

2008-01-01

Blends of poly(methyl methacrylate) (PMMA) were prepared with aluminum tribromide (AlBr/sub 3/) and aluminum acetylacetonate (Al(acac)/sub 3/) in definite ratios. Thermal studies (TG-DTG-DTA) of polymer and blends with both additives were carried out in inert atmosphere to investigate the mode of degradation and the effects of stability/destability on either component. The addition of compounds in polymer resulted early decompositions. The intermediates formed during decomposition were also identified. The possible explanation of the thermal degradation reactions is advanced on the basis of results gathered. The apparent activation energy (E/sub o/) and order of reaction (n) of the pyrolytic reactions were determined by Horowitz and Metzger method from the corresponding TG curves. (author)

Dynamic environmental transmission electron microscopy observation of platinum electrode catalyst deactivation in a proton-exchange-membrane fuel cell.

Science.gov (United States)

Yoshida, Kenta; Xudong, Zhang; Bright, Alexander N; Saitoh, Koh; Tanaka, Nobuo

2013-02-15

Spherical-aberration-corrected environmental transmission electron microscopy (AC-ETEM) was applied to study the catalytic activity of platinum/amorphous carbon electrode catalysts in proton-exchange-membrane fuel cells (PEMFCs). These electrode catalysts were characterized in different atmospheres, such as hydrogen and air, and a conventional high vacuum of 10(-5) Pa. A high-speed charge coupled device camera was used to capture real-time movies to dynamically study the diffusion and reconstruction of nanoparticles with an information transfer down to 0.1 nm, a time resolution below 0.2 s and an acceleration voltage of 300 kV. With such high spatial and time resolution, AC-ETEM permits the visualization of surface-atom behaviour that dominates the coalescence and surface-reconstruction processes of the nanoparticles. To contribute to the development of robust PEMFC platinum/amorphous carbon electrode catalysts, the change in the specific surface area of platinum particles was evaluated in hydrogen and air atmospheres. The deactivation of such catalysts during cycle operation is a serious problem that must be resolved for the practical use of PEMFCs in real vehicles. In this paper, the mechanism for the deactivation of platinum/amorphous carbon electrode catalysts is discussed using the decay rate of the specific surface area of platinum particles, measured first in a vacuum and then in hydrogen and air atmospheres for comparison.

Molecular absorption spectra of beryllium, cerium, lanthanum, iron, and platinum salts

International Nuclear Information System (INIS)

Daidoji, Hidehiro

1980-01-01

The absorption spectra of some salts of beryllium, cerium, lanthanum, iron and platinum in air-acetylene flame were measured in the wavelength range from 200 to 400 nm. A Hitachi 207 type atomic absorption spectrophotometer was used. A deuterium lamp, a home-made continuous radiation lamp and some hollow cathode lamps were used as light sources. The new molecular absorption spectra of cerium, lanthanum and platinum and the absorption spectra due to Be(OH) 2 , LaO, PtH, FeO and FeCl in 200-400 nm region were obtained. Emission spectra of CeO, LaO and FeOH were also obtained. These molecular absorption bands were estimated as absorption errors of maximum 15 times to the sensitivity of each elements in atomic absorption spectrometry. In addition, spectral line interferences of iron were observed in atomic absorption spectrometry of Zn, Cd, Ni, Cu and Cr. (author)

Interaction of Classical Platinum Agents with the Monomeric and Dimeric Atox1 Proteins: A Molecular Dynamics Simulation Study

Directory of Open Access Journals (Sweden)

Xiaolei Wang

2013-12-01

Full Text Available We carried out molecular dynamics simulations and free energy calculations for a series of binary and ternary models of the cisplatin, transplatin and oxaliplatin agents binding to a monomeric Atox1 protein and a dimeric Atox1 protein to investigate their interaction mechanisms. All three platinum agents could respectively combine with the monomeric Atox1 protein and the dimeric Atox1 protein to form a stable binary and ternary complex due to the covalent interaction of the platinum center with the Atox1 protein. The results suggested that the extra interaction from the oxaliplatin ligand–Atox1 protein interface increases its affinity only for the OxaliPt + Atox1 model. The binding of the oxaliplatin agent to the Atox1 protein might cause larger deformation of the protein than those of the cisplatin and transplatin agents due to the larger size of the oxaliplatin ligand. However, the extra interactions to facilitate the stabilities of the ternary CisPt + 2Atox1 and OxaliPt + 2Atox1 models come from the α1 helices and α2-β4 loops of the Atox1 protein–Atox1 protein interface due to the cis conformation of the platinum agents. The combinations of two Atox1 proteins in an asymmetric way in the three ternary models were analyzed. These investigations might provide detailed information for understanding the interaction mechanism of the platinum agents binding to the Atox1 protein in the cytoplasm.

Molecular adsorption of alkanes on platinum surfaces: A predictive theoretical model

International Nuclear Information System (INIS)

Stinnett, J.A.; Madix, R.J.

1996-01-01

The adsorption probabilities of methane and propane on Pt(111), and propane on Pt(110)-(1x2) have been successfully predicted for a wide range of incident energies and angles with classical stochastic trajectory simulations, using a pairwise additive Morse methyl endash platinum potential previously developed from the measured trapping probabilities of ethane on Pt(111). These predictions, along with those for ethane adsorption on Pt(110)endash(1x2), comprise a unified model for the molecular adsorption of alkanes on platinum surfaces. The simulations show the initial trapping probabilities of methane and propane on Pt(111) are determined to within approximately 10% by the fate of the first bounce. They also indicate that at normal incidence on Pt(111) energy conversions from perpendicular translational motion to both cartwheeling rotation and lattice phonons play increasingly important roles in increasing the trapping probability as the alkane increases in size and molecular weight. For methane itself excitation of parallel translational momentum after the first bounce serves as the most effective energy storage mechanism which facilitates trapping, whereas for propane cartwheel rotational motion plays the dominant role. Excessive excitation of these modes of motion, however, can cause scattering on subsequent bounces by reconversion of the energy into perpendicular translational energy. Collisions of methane with the hollow and bridge sites on the Pt(111) surface appear less effective in trapping than do atop sites. The simulations also suggest excitation of the C endash C endash C bending mode of propane has little effect on the trapping of propane on platinum surfaces for beam energies below 55 kJ/mol. copyright 1996 American Institute of Physics

Synthesis and spectroscopic characterization of some lanthanide(III nitrate complexes of ethyl 2-[2-(1-acetyl-2-oxopropylazo]-4,5-dimethyl-3-thiophenecarboxyate

Directory of Open Access Journals (Sweden)

CHEMPAKAM JANARDHANAN ATHIRA

2011-02-01

Full Text Available Ethyl 2-[2-(1-acetyl-2-oxopropylazo]-4,5-dimethyl-3-thiophenecarboxyate was synthesized by coupling diazotized ethyl 2-amino-4,5-dimethylthiophene-3-carboxylate with acetylacetone. Based on various spectral studies and elemental analysis, an intramolecularly hydrogen-bonded azo-enol structural form was assigned for the ligand. This ligand is versatile in forming a series of lanthanide(III complexes, viz., lanthanum(III, cerium(III, praseodymium(III, neodymium(III, samarium(III and gadolinium(III, which were characterized through various spectral studies, elemental analysis, magnetic susceptibility measurements, molar conductance and thermal analysis. The spectral data revealed that the ligand acted as a neutral tridentate, coordinating to the metal ion through one of the azo nitrogen atoms, the ester carbonyl and the enolic oxygen of the acetylacetone moiety, without deprotonation. Molar conductance values adequately supported their non-electrolytic nature. The ligand and lanthanum(III complex were subjected to X-ray diffraction studies. In addition, the lanthanum(III complex underwent a facile transesterification reaction on refluxing with methanol for a long period. The thermal behaviour of the lanthanum(III complex was also examined

SEROTONIN METABOLISM FOLLOWING PLATINUM-BASED CHEMOTHERAPY COMBINED WITH THE SEROTONIN TYPE-3 ANTAGONIST TROPISETRON

NARCIS (Netherlands)

SCHRODER, CP; VANDERGRAAF, WTA; KEMA, IP; GROENEWEGEN, A; SLEIJFER, DT; DEVRIES, EGE

1995-01-01

The administration of platinum-based chemotherapy induces serotonin release from the enterochromaffin cells, causing nausea and vomiting. This study was conducted to evaluate parameters of serotonin metabolism following platinum-based chemotherapy given in combination with the serotonin type-3

Phosphorescence quantum yield determination with time-gated fluorimeter and Tb(III)-acetylacetonate as luminescence reference

Energy Technology Data Exchange (ETDEWEB)

Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Fakultät für Physik, Universität Regensburg, Universitätsstrasse 31, D-93053 Regensburg (Germany)

2013-03-29

Highlights: ► Procedure for absolute phosphorescence quantum yield measurement is described. ► Experimental setup for absolute luminescence quantum yield standard calibration. ► Tb(acac){sub 3} proposed as phosphorescence quantum yield reference standard. ► Luminescence quantum yield of Tb(acac){sub 3} in cyclohexane measured. ► Luminescence lifetime of Tb(acac){sub 3} in cyclohexane measured. - Abstract: Phosphorescence quantum yield measurements of fluorescent and phosphorescent samples require the use of time-gated fluorimeters in order to discriminate against the fluorescence contribution. As reference standard a non-fluorescent luminescent compound is needed for absolute phosphorescence quantum yield determination. For this purpose the luminescence behavior of the rare earth chelate terbium(III)-acetylacetonate (Tb(acac){sub 3}) was studied (determination of luminescence quantum yield and luminescence lifetime). The luminescence quantum yield of Tb(acac){sub 3} was determined by using an external light source and operating the fluorimeter in chemo/bioluminescence mode with a fluorescent dye (rhodamine 6G in methanol) as reference standard. A procedure is developed for absolute luminescence (phosphorescence) quantum yield determination of samples under investigation with a time-gated fluorimeter using a non-fluorescent luminescent compound of known luminescence quantum yield and luminescence lifetime.

Arresting mantle formation and redirecting embryonic shell gland tissue by platinum2+ leads to body plan modifications in Marisa cornuarietis (Gastropoda, Ampullariidae).

Science.gov (United States)

Marschner, Leonie; Triebskorn, Rita; Köhler, Heinz-R

2012-08-01

To evaluate the threat that anthropogenic substances pose to animals when they are emitted into the environment, tests like the invertebrate embryo toxicity test with the ramshorn snail Marisa cornuarietis have been developed. These tests are used to investigate substances like the heavy metal platinum (Pt) that is used in catalytic converters and is gradually released in car exhausts. In 2010, our group reported that high Pt concentrations cause body plan alterations in snails and prevent the formation of an external shell during M. cornuarietis embryogenesis. Now, this study presents scanning-electron micrographs and histological sections of platinum(2+) (Pt(2+))-treated and untreated M. cornuarietis embryos and compares "normally" developing and "shell-less" embryos during embryogenesis, to reveal the exact course of events that lead to this body plan shift. Both groups showed similar development until the onset of torsion 70- to 82-h postfertilization. In the Pt(2+)-exposed embryos, the rudimentary shell gland (=anlage of both shell gland and mantle, which usually evaginates, grows, and eventually covers the visceral sac) does not spread across the visceral sac but remains on its ventral side. Without the excessive growth of the shell gland, a horizontal rotation of the visceral sac relative to head and foot does not occur, as being normal during the process of torsion. Copyright © 2012 Wiley Periodicals, Inc.

Ruthenium–Platinum Catalysts and Direct Methanol Fuel Cells (DMFC: A Review of Theoretical and Experimental Breakthroughs

Directory of Open Access Journals (Sweden)

Ana S. Moura

2017-02-01

Full Text Available The increasing miniaturization of devices creates the need for adequate power sources and direct methanol fuel cells (DMFC are a strong option in the various possibilities under current development. DMFC catalysts are mostly based on platinum, for its outperformance in three key areas (activity, selectivity and stability within methanol oxidation framework. However, platinum poisoning with products of methanol oxidation led to the use of alloys. Ruthenium–platinum alloys are preferred catalysts active phases for methanol oxidation from an industrial point of view and, indeed, ruthenium itself is a viable catalyst for this reaction. In addition, the route of methanol decomposition is crucial in the goal of producing H2 from water reaction with methanol. However, the reaction pathway remains elusive and new approaches, namely in computational methods, have been ensued to determine it. This article reviews the various recent theoretical approaches for determining the pathway of methanol decomposition, and systematizes their validation with experimental data, within methodological context.

A matched-pair comparison of intensity-modulated radiation therapy with cetuximab versus intensity-modulated radiation therapy with platinum-based chemotherapy for locally advanced head neck cancer

International Nuclear Information System (INIS)

Huang, J.; Baschnagel, A.M.; Chen, P.; Ye, H.; Krauss, D.; Gustafson, G.; Jaiyesmi, I.; Folbe, M.; Akervall, J.

2014-01-01

We retrospectively compared the efficacy of intensity-modulated radiotherapy (IMRT) and cetuximab (IMRT/cetuximab) versus IMRT and platinum-based chemotherapy (IMRT/platinum) for locally advanced head neck squamous cell carcinoma (LAHNSCC). Thirty-one IMRT/cetuximab patients were matched 1:2 with 62 IMRT/platinum patients according to primary site and clinical stage. The primary endpoint was locoregional recurrence (LRR), and secondary endpoints included distant metastasis (DM), cause-specific survival (CSS), and overall survival (OS). Because of inherent selection bias, the IMRT/cetuximab cohort was significantly older and with a higher Charlson Comorbidity Index. IMRT/cetuximab and IMRT/platinum did not have significantly different LRR and DM (33 vs. 23% at 2 years, P=0.22; 17 vs. 11% at 2 years, P=0.40; respectively). IMRT/cetuximab had significantly worse CSS and OS (67 vs. 84%, P=0.04; 58 vs. 83%, P=0.001; respectively). However, for the subset of elderly patients ≥65 years old, there is no difference between the two cohorts for all endpoints (all P=NS). IMRT/platinum should remain the preferred choice of chemoradiotherapy for LAHNSCC, but IMRT/cetuximab may be a reasonable alternative for elderly patients. (author)

A Potential Bone-Targeting Hypotoxic Platinum(II) Complex with an Unusual Cytostatic Mechanism toward Osteosarcoma Cells.

Science.gov (United States)

Zhang, Zhenqin; Zhu, Zhenzhu; Luo, Cheng; Zhu, Chengcheng; Zhang, Changli; Guo, Zijian; Wang, Xiaoyong

2018-03-19

Osteosarcoma (OS) is the most common primary pediatric bone tumor lethal to children and adolescents. Chemotherapeutic agents such as cisplatin are not effective for OS because of their poor accessibility to this cancer and severe systemic toxicity. In this study, a lipophilic platinum(II) complex bearing a bisphosphonate bone-targeting moiety, cis-[PtL(NH 3 ) 2 Cl]NO 3 {BPP; L = tetraethyl [2-(pyridin-2-yl)ethane-1,1-diyl]bisphosphonate}, was prepared and characterized by NMR, electrospray ionization mass spectrometry, and single-crystal X-ray crystallography. The cytotoxicity of BPP toward OS cell lines U2OS and MG-63 was tested by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. BPP exhibits moderate inhibition against U2OS cells through a mechanism involving both DNA binding and a mevalonate pathway. The acute toxicity of BPP to mice is 7-fold lower than that of cisplatin. The relative low systemic toxicity may result from the steric hindrance of the ligand, which blocks BPP approaching the bases of DNA. The results suggest that incorporating bisphosphonates into a platinum complex not only enhances its bone-targeting property but also minimizes its reactivity toward DNA and thereby lowers the systematic toxicity of the complex. The diminished cytotoxicity of BPP could be compensated for by increasing the therapeutic dose with marginal harm. This strategy provides a new possibility for overcoming the ineffectiveness and systemic toxicity of platinum drugs in the treatment of OS.

Superconductivity observed in platinum-silicon interface

Energy Technology Data Exchange (ETDEWEB)

Kuo, Pai-Chia, E-mail: paichia@phys.sinica.edu.tw [Research Program on Nanoscience and Nanotechnology, Academia Sinica, Taipei 11529, Taiwan (China); Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China); Department of Materials Science and Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Chen, Chun-Wei [Department of Materials Science and Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Lee, Ku-Pin; Shiue, Jessie, E-mail: yshiue@phys.sinica.edu.tw [Research Program on Nanoscience and Nanotechnology, Academia Sinica, Taipei 11529, Taiwan (China); Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China)

2014-05-26

We report the discovery of superconductivity with an onset temperature of ∼0.6 K in a platinum-silicon interface. The interface was formed by using a unique focused ion beam sputtering micro-deposition method in which the energies of most sputtered Pt atoms are ∼2.5 eV. Structural and elemental analysis by transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy reveal a ∼ 7 nm interface layer with abundant Pt, which is the layer likely responsible for the superconducting transport behavior. Similar transport behavior was also observed in a gold-silicon interface prepared by the same technique, indicating the possible generality of this phenomenon.

Separation of gold, palladium and platinum in chromite by anion exchange chromatography for inductively coupled plasma atomic emission spectrometric analysis

International Nuclear Information System (INIS)

Choi, Kwang Soon; Lee, Chang Heon; Park, Yeong Jae; Joe, Kih Soo; Kim, Won Ho

2001-01-01

A study has been carried out on the separation of gold, iridium, palladium, rhodium, ruthenium and platinum in chromite samples and their quantitative determination using inductively coupled plasma atomic emission spectrometry (ICP-AES). The dissolution condition of the minerals by fusion with sodium peroxide was optimized and chromatographic elution behavior of the rare metals was investigated by anion exchange chromatography. Spectral interference of chromium, a matrix of the minerals, was investigated on determination of gold. Chromium interfered on determination of gold at the concentration of 500 mg/L and higher. Gold plus trace amounts of iridium, palladium, rhodium and ruthenium, which must be preconcentrated before ICP-AES was separated by anion exchange chromatography after reducing Cr(VI) to Cr(III) by H 2 O 2 . AuCl - 4 retained on the resin column was selectively eluted with acetone- HNO 3 -H 2 O as an eluent. In addition, iridium, palladium, rhodium and ruthenium remaining on the resin column were eluted as a group with concentrated HCl. However, platinum was eluted with concentrated HNO 3 . The recovery yield of gold with acetone-HNO 3 -H 2 O was 100.7 ± 2.0 % , and the yields of palladium and platinum with concentrated HCl and HNO 3 were 96.1 ± 1.8% and 96.6 ± 1.3%, respectively. The contents of gold and platinum in a Mongolian chromite sample were 32.6 ± 2.2 μg/g and 1.6 ± 0.14 μg/g, respectively. Palladium was not detected

Prophage induction and mutagenicity of a series of anti-tumour platinum(II) and platinum(IV) co-ordination complexes

NARCIS (Netherlands)

Mattern, I.E.; Cocchiarella, L.; Kralingen, C.G. van; Lohman, P.H.M.

1982-01-01

Eleven platinum compounds with nitrogen donor ligands, previously tested for anti-tumour activity were studied for induction of prophage lambda and for mutagenicity in the Ames assay, with various strains of Salmonella. The compounds included cis and trans isomers of Pt(II) and Pt(IV) complexes and

Platinum-group element mineralization

International Nuclear Information System (INIS)

Gruenewaldt, G.

1985-01-01

The purpose of this investigation is to determine the geological processes responsible for the abnormal enrichment of the platinum-group elements (PGE) in the mineralized layers of the Bushveld Complex. Questions asked are: what processes caused enrichment of the Bushveld magma in the PGE ; by what processes were these PGE concentrated in the mineralized layers ; was contamination of the Bushveld magma from external sources important in the formation of the PGE enriched layers ; what are the effects of fractional crystallization on the PGE ratios

Rockburst damage mechanism at Impala Platinum Mine

CSIR Research Space (South Africa)

Ledwaba, LS

2012-05-01

Full Text Available Impala Platinum Mine (Impala), situated north of the town of Rustenburg in the North West Province of South Africa, has experienced an increase in seismicity from ~841 seismic events in the year 2005 to ~1588 seismic events in 2008...

Sustained platelet-sparing effect of weekly low dose paclitaxel allows effective, tolerable delivery of extended dose dense weekly carboplatin in platinum resistant/refractory epithelial ovarian cancer

Directory of Open Access Journals (Sweden)

Blagden Sarah

2011-07-01

Full Text Available Abstract Background Platinum agents have shown demonstrable activity in the treatment of patients with platinum resistant, recurrent ovarian cancer when delivered in a "dose-dense" fashion. However, the development of thrombocytopenia limits the weekly administration of carboplatin to no greater than AUC 2. Paclitaxel has a well-described platelet sparing effect however its use to explicitly provide thromboprotection in the context of dose dense carboplatin has not been explored. Methods We treated seven patients with platinum resistant ovarian cancer who had previously received paclitaxel or who had developed significant peripheral neuropathy precluding the use of further full dose weekly paclitaxel. Results We were able to deliver carboplatin AUC 3 and paclitaxel 20 mg/m2 with no thrombocytopenia or worsening of neuropathic side-effects, and with good activity. Conclusions We conclude that this regimen may be feasible and active, and could be formally developed as a "platinum-focussed dose-dense scaffold" into which targeted therapies that reverse platinum resistance can be incorporated, and merits further evaluation.

Spatial and temporal distribution of platinum, palladium and rhodium in Zagreb air.

Science.gov (United States)

Rinkovec, Jasmina; Pehnec, Gordana; Godec, Ranka; Davila, Silvije; Bešlić, Ivan

2018-09-15

Platinum (Pt), palladium (Pd) and rhodium (Rh) are most widely used in the production of automotive catalytic converters that serve to reduce toxic emissions from motor vehicles. The aim of this study was to quantitatively determine the levels of platinum, palladium and rhodium in the PM 10 and PM 2.5 fraction of airborne particle matter and find their spatial and temporal distribution at different polluted areas of the city of Zagreb, Croatia. The method used in this paper included weekly sampling of airborne particle matter on quartz filters, microwave digestion in acid under high pressure and temperature, and analysis by inductively coupled plasma mass spectrometry (ICP MS). The results have shown that the highest mean values at all three sampling stations (North, Center, South) were obtained for palladium (3.856 pg m -3 , 5.396 pg m -3 , 5.600 pg m -3 ) and the lowest for rhodium (0.444 pg m -3 , 0.643 pg m -3 , 0.750 pg m -3 ). The average mass concentrations of platinum group elements (PGE) in PM 10 increased for all three elements in the direction North Zagreb are the first results of their kind for this area and will provide insights into the contribution of catalytic converters to the presence of these elements in the environment. Copyright © 2018 Elsevier B.V. All rights reserved.

Cisplatin-Loaded Porous Si Microparticles Capped by Electroless Deposition of Platinum

Science.gov (United States)

Park, Jennifer S.; Kinsella, Joseph M.; Jandial, Danielle D.; Howell, Stephen B.

2012-01-01

The loading and release of the anti-cancer drug platinum cis-dichlorodiamine (cisplatin) from mesoporous silicon (pSi) microparticles is studied. The pSi microparticles are modified with 1-dodecene or with 1,12-undecylenic acid by hydrosilylation, and each modified pSi material acts as a reducing agent, forming a deposit of Pt on its surface that nucleates further deposition, capping the mesoporous structure and trapping free (unreduced) cisplatin within. Slow oxidation and hydrolytic dissolution of the Si/SiO2 matrix in buffer solution or in culture medium leads to the release of drugs from the microparticles. The drug-loaded particles show significantly greater toxicity toward human ovarian cancer cells (in vitro), relative to an equivalent quantity of free cisplatin. This result is consistent with the mechanism of drug release, which generates locally high concentrations of the drug in the vicinity of the degrading particles. Control assays with pSi particles loaded in a similar manner with the therapeutically inactive trans isomer of the platinum drug, and with pSi particles containing no drug, result in low cellular toxicity. A hydrophobic prodrug, cis,trans,cis-[Pt(NH3)2(O2C(CH2)8CH3)2Cl2], is loaded into the pSi films from chloroform without concomitant reduction of the pSi carrier. PMID:21630444

Cyclic voltammetric investigations of microstructured and platinum-covered glassy carbon electrodes in contact with a polymer electrolyte membrane

Energy Technology Data Exchange (ETDEWEB)

Scherer, G G; Veziridis, Z; Staub, M [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Freimuth, H [Inst. fuer Mikrotechnik Mainz IMM, Mainz (Germany)

1997-06-01

Model gas diffusion electrodes were prepared by microstructuring glassy carbon surfaces with high aspect ratios and subsequent deposition of platinum. These electrodes were characterized by hydrogen under-potential deposition (H-upd) in contact with a polymer electrolyte membrane employing cyclic voltametry. H-upd was found on platinum areas not in direct contact to the solid electrolyte, as long as a continuous platinum-path existed. A carbon surface between platinum acts as barrier for H-upd. (author) 4 figs., 5 refs.

Interaction of Newly Platinum(II) with Tris(2-carboxyethyl)phosphine Complex with DNA and Model Lipid Membrane

Czech Academy of Sciences Publication Activity Database

Pruchnik, H.; Kral, Teresa; Hof, Martin

2017-01-01

Roč. 250, č. 5 (2017), s. 461-470 ISSN 0022-2631 R&D Projects: GA ČR(CZ) GBP208/12/G016 Institutional support: RVO:61388955 Keywords : dna * DPPC bilayer * dsc * IR spectroscopy * Platinum(II) complex * tcspc-fcs Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 1.696, year: 2016

Synthesis, structural characterization, and pro-apoptotic activity of 1-indanone thiosemicarbazone platinum(II) and palladium(II) complexes: potential as antileukemic agents.

Science.gov (United States)

Gómez, Natalia; Santos, Diego; Vázquez, Ramiro; Suescun, Leopoldo; Mombrú, Alvaro; Vermeulen, Monica; Finkielsztein, Liliana; Shayo, Carina; Moglioni, Albertina; Gambino, Dinorah; Davio, Carlos

2011-08-01

In the search for alternative chemotherapeutic strategies against leukemia, various 1-indanone thiosemicarbazones, as well as eight novel platinum(II) and palladium(II) complexes, with the formula [MCl₂(HL)] and [M(HL)(L)]Cl, derived from two 1-indanone thiosemicarbazones were synthesized and tested for antiproliferative activity against the human leukemia U937 cell line. The crystal structure of [Pt(HL1)(L1)]Cl·2MeOH, where L1=1-indanone thiosemicarbazone, was solved by X-ray diffraction. Free thiosemicarbazone ligands showed no antiproliferative effect, but the corresponding platinum(II) and palladium(II) complexes inhibited cell proliferation and induced apoptosis. Platinum(II) complexes also displayed selective apoptotic activity in U937 cells but not in peripheral blood monocytes or the human hepatocellular carcinoma HepG2 cell line used to screen for potential hepatotoxicity. Present findings show that, in U937 cells, 1-indanone thiosemicarbazones coordinated to palladium(II) were more cytotoxic than those complexed with platinum(II), although the latter were found to be more selective for leukemic cells suggesting that they are promising compounds with potential therapeutic application against hematological malignancies. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ganoderma-Like MoS2 /NiS2 with Single Platinum Atoms Doping as an Efficient and Stable Hydrogen Evolution Reaction Catalyst.

Science.gov (United States)

Guan, Yongxin; Feng, Yangyang; Wan, Jing; Yang, Xiaohui; Fang, Ling; Gu, Xiao; Liu, Ruirui; Huang, Zhengyong; Li, Jian; Luo, Jun; Li, Changming; Wang, Yu

2018-05-27

Herein, a unique ganoderma-like MoS 2 /NiS 2 hetero-nanostructure with isolated Pt atoms anchored is reported. This novel ganoderma-like heterostructure can not only efficiently disperse and confine the few-layer MoS 2 nanosheets to fully expose the edge sites of MoS 2 , and provide more opportunity to capture the Pt atoms, but also tune the electronic structure to modify the catalytic activity. Because of the favorable dispersibility and exposed large specific surface area, single Pt atoms can be easily anchored on MoS 2 nanosheets with ultrahigh loading of 1.8 at% (the highest is 1.3 at% to date). Owing to the ganoderma-like structure and platinum atoms doping, this catalyst shows Pt-like catalytic activity for the hydrogen evolution reaction with an ultralow overpotential of 34 mV and excellent durability of only 2% increase in overpotential for 72 h under the constant current density of 10 mA cm -2 . © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Platinum(II)-gadolinium(III) complexes as potential single-molecular theranostic agents for cancer treatment.

Science.gov (United States)

Zhu, Zhenzhu; Wang, Xiaoyong; Li, Tuanjie; Aime, Silvio; Sadler, Peter J; Guo, Zijian

2014-11-24

Theranostic agents are emerging multifunctional molecules capable of simultaneous therapy and diagnosis of diseases. We found that platinum(II)-gadolinium(III) complexes with the formula [{Pt(NH3)2Cl}2GdL](NO3)2 possess such properties. The Gd center is stable in solution and the cytoplasm, whereas the Pt centers undergo ligand substitution in cancer cells. The Pt units interact with DNA and significantly promote the cellular uptake of Gd complexes. The cytotoxicity of the Pt-Gd complexes is comparable to that of cisplatin at high concentrations (≥0.1 mM), and their proton relaxivity is higher than that of the commercial magnetic resonance imaging (MRI) contrast agent Gd-DTPA. T1-weighted MRI on B6 mice demonstrated that these complexes can reveal the accumulation of platinum drugs in vivo. Their cytotoxicity and imaging capabilities make the Pt-Gd complexes promising theranostic agents for cancer treatment. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sulfur tolerant zeolite supported platinum catalysts for aromatics hydrogenation

Energy Technology Data Exchange (ETDEWEB)

Bergem, Haakon

1997-12-31

The increased demand for transportation fuels at the expence of heavier fuel oil has forced the refinery industry to expand their conversion capacity with hydrotreating as one of the key processes. A shift towards more diesel powered vehicles along with tightening fuel regulations demanding cleaner fuels has lead to increasing interest in catalytic processes for the manufacturing of such environmentally acceptable fuels. This provides the motivation for this thesis. Its main objective was to study possible catalysts active for desulfurization, hydrogenation, and ring-opening of aromatics all in the presence of sulfur. A close examination of the physical properties and kinetical behaviour of the chosen catalysts has been performed. A high pressure reactor setup was designed and built for activity measurements. Zeolite supported platinum catalysts were prepared and both the metal and acid functions were characterized utilizing various experimental techniques. Hydrogenation of toluene was used as a model reaction and the effect of sulfur adsorption on the activity and kinetic behaviour of the catalysts was investigated. The catalyst samples showed hydrogenation activities comparable to a commercial Pt/Al2O3 catalyst. There were no clear differences in the effect of the various sulfur compounds studied. Platinum supported on zeolite Y gave considerably more sulfur tolerant catalysts compared to Al2O3 as support. 155 refs., 58 figs., 36 tabs.

Synthesis of carbon-14 labelled cis-malonato [(4R,5R)-4,5-bis(aminomethyl)-2-isopropyl-1,3-dioxolane] platinum(II) (SKI 2053R)

International Nuclear Information System (INIS)

Kim, Dae-Kee; Kim, Youngseok; Rim, Jonggill; Kim, Ganghyeok; Gam, Jongsik; Song, Sungkun; Yoo, Kwanghee; Kim, Key H.

1994-01-01

The synthesis of 14 C-labelled cis-malonato[(4R,5R)-4,5-bis(aminomethyl)-2-isopropyl-1,3-dioxolan e]platinum(II) from [1,4- 14 C] D-tartaric acid is described. The overall radiochemical yield of the product in a eight-step sequence was 23.8% and radiochemical purity was 98.5%. (author)

Effect of the platinum content on the microstructure and micropore size distribution of Pt/alumina-pillared clays.

Science.gov (United States)

Barrera-Vargas, M; Valencia-Rios, J; Vicente, M A; Korili, S A; Gil, A

2005-12-15

The aim of this work is to study the effect of the platinum content (0-1.8 wt % Pt) on the microstructure of an alumina-pillared clay. For this purpose, the nitrogen physisorption data at -196 degrees C, the micropore size distributions of the supported platinum catalysts, and the hydrogen chemisorption results at 30 degrees C have been analyzed and compared. The preparation of the catalysts has modified the textural properties of the Al-pillared clay support, giving rise to a loss of surface area and micropore volume. After reduction at 420 degrees C, the presence of dispersed metallic platinum with mean crystallite size in the 22-55 A range has been found by hydrogen adsorption. Comparison of all results reveals that the platinum species block the micropore entrances by steric hindrance to nitrogen access as the platinum content increases.

A platinum in-core flux detector

International Nuclear Information System (INIS)

Shields, R.B.

1976-01-01

The performance is described of a platinum emitter self-powered detector having the following parameters: emitter diameter 0.51 mm, Inconel 600 collector of 1.5 mm outer diameter and 0.25 mm wall thickness, compacted powder MgO insulant, thermal neutron flux 10 14 n.cm -2 .s -1 and gamma radiation dose rate 1.2 x 10 8 rad.h -1 . The advantage of the detector is its sensitivity to both neutrons and gamma radiation. A comparison is made with other types of detectors using Ce, Ta, Os, Rh, V, Co, Zr as emitters, especially in relation to the emitter response time to neutrons or gammas, the output signal amplitude, sensitivity, and the emitter half-life. Extensive tests of the detectors proceeded for two years on the NRU and CANDU-BLW reactors in Gentilly, Canada. (J.B.)

Efficient light-emitting devices based on platinum-complexes-anchored polyhedral oligomeric silsesquioxane materials

KAUST Repository

Yang, Xiaohui

2010-08-24

The synthesis, photophysical, and electrochemical characterization of macromolecules, consisting of an emissive platinum complex and carbazole moieties covalently attached to a polyhedral oligomeric silsesquioxane (POSS) core, is reported. Organic light-emitting devices based on these POSS materials exhibit a peak external quantum efficiency of ca. 8%, which is significantly higher than that of the analogous devices with a physical blend of the platinum complexes and a polymer matrix, and they represent noticeable improvement in the device efficiency of solution-processable phosphorescent excimer devices. Furthermore, the ratio of monomer and excimer/aggregate electroluminescent emission intensity, as well as the device efficiency, increases as the platinum complex moiety presence on the POSS macromolecules decreases. © 2010 American Chemical Society.

Determination of platinum group metals by ICP-AES in environmental samples after preconcentration

International Nuclear Information System (INIS)

Vlasankova, R.; Sommer, L.

1999-01-01

Platinum group metal (PGM) may have toxic properties and their presence in the environment represent danger for human health. With the introduction of automobile catalytic converters containing PGM, the emission of these noble metals into atmosphere has increased. Platinum, palladium and rhodium are used in this catalytic converters to decrease toxic emissions of carbon monoxide, unburnt hydrocarbons and nitrogen oxides in vehicles exhaust gases. These catalysts are mobile sources of PGM into the environment. Thus, increased platinum concentrations have been found in various objects of environment because of the massive introduction of such catalytic converters are present. The preconcentration and separation of PGM and their determination by ICP-AES in environmental samples are described

A randomized phase 2 study of combination cediranib and olaparib versus olaparib alone as recurrence therapy in platinum-sensitive ovarian cancer

Science.gov (United States)

Liu, Joyce F.; Barry, William T.; Birrer, Michael; Lee, Jung-Min; Buckanovich, Ronald J.; Fleming, Gini F.; Rimel, BJ; Buss, Mary K.; Nattam, Sreenivasa; Hurteau, Jean; Luo, Weixiu; Quy, Philippa; Whalen, Christin; Obermayer, Lisa; Lee, Hang; Winer, Eric P.; Kohn, Elise C.; Ivy, S. Percy; Matulonis, Ursula A.

2015-01-01

Background Olaparib is an oral poly(ADP-ribose) polymerase inhibitor and cediranib is an oral anti-angiogenic with activity against VEGFR-1, 2, and 3. Both agents have antitumor activity in women with recurrent ovarian cancer, and the combination of these agents was active and had manageable toxicities in a Phase 1 trial. We asked whether the combination of cediranib and olaparib could improve progression-free survival compared to olaparib monotherapy in women with recurrent platinum-sensitive ovarian cancer. Methods We conducted a randomized, open-label, phase 2 study to evaluate the activity of olaparib monotherapy compared with combination cediranib and olaparib in women with ovarian cancer with measurable platinum-sensitive, relapsed, high-grade serous or endometrioid disease or those with deleterious germline BRCA1/2 mutations (gBRCAm). Patients were randomized using permuted blocks within stratum defined by gBRCA status and prior anti-angiogenic therapy to receive olaparib capsules 400mg twice daily or the combination at the recommended phase 2 dose of cediranib 30mg daily and olaparib capsules 200mg twice daily. The primary endpoint was progression-free survival (PFS) analyzed under intention to treat. The trial is registered with ClinicalTrials.gov, NCT01116648. The Phase 2 portion of the trial reported here is no longer accruing patients. Findings Forty-six of 90 randomized patients received olaparib alone, and 44 received cediranib/olaparib. Median PFS was significantly longer with cediranib/olaparib (17.7 vs. 9.0 mos, HR 0.42; p = 0.005). Grade 3 and 4 adverse events were more common with cediranib/olaparib, including fatigue (12 vs. 5), diarrhea (10 vs. 0), and hypertension (18 vs. 0). Subset analysis within stratum defined by BRCA1/2 status demonstrated activity of cediranib/olaparib in both gBRCAm and gBRCAwt/u (wild-type/unknown) patients. Significant improvement in PFS occurred in gBRCAwt/u women receiving cediranib/olaparib (16.5 vs. 5.7 mos, p = 0

Enhancement of oxidative electrocatalytic properties of platinum nanoparticles by supporting onto mixed WO{sub 3}/ZrO{sub 2} matrix

Energy Technology Data Exchange (ETDEWEB)

Rutkowska, Iwona A., E-mail: ilinek@chem.uw.edu.pl; Wadas, Anna; Kulesza, Pawel J., E-mail: pkulesza@chem.uw.edu.pl

2016-12-01

Highlights: • The electrocatalytic system utilizing Pt nanoparticles dispersed on mixed metal oxide (WO{sub 3}/ZrO{sub 2}) system is proposed. • The system is characterized by high activity toward oxidations of ethanol, methanol and acetaldehyde in acid medium. • The enhancement effect is facilitated by presence of hydroxyl groups, high mobility of protons and improved distribution of electrons. • Strong interactions between Pt and the mixed oxide WO{sub 3}/ZrO{sub 2} support are postulated. - Abstract: Nanostructured mixed metal (W, Zr) oxide matrices (in a form of layered intercalated films of WO{sub 3} and ZrO{sub 2}) are considered here for supporting and activating catalytic platinum nanoparticles toward electrooxidation of ethanol. Remarkable increases of electrocatalytic (voltammetric, chronoamperometric) currents measured in 0.5 mol dm{sup −3} H{sub 2}SO{sub 4} (containing 0.5 mol dm{sup −3} ethanol) have been observed. Comparison has been made to the behavior of methanol and acetaldehyde under analogous conditions. The enhancement effects are interpreted in terms of specific interactions between platinum nanoparticles and the metal oxide species, high acidity of the mixed oxide sites, as well as high population of surface hydroxyl groups and high mobility of protons existing in close vicinity of Pt catalytic sites. The metal oxide nanostructures are expected to interact competitively (via the surface hydroxyl groups) with adsorbates of the undesirable reaction intermediates, including CO, facilitating their desorption (“third body effect”), or even oxidative removal (e.g., of CO to CO{sub 2}). The fact that the partially reduced tungsten oxide (H{sub x}WO{sub 3}) component is characterized by fast electron transfers coupled to proton displacements tends to improve the overall charge propagation at the electrocatalytic interface.

Titanium Oxide/Platinum Catalysis: Charge Transfer from a Titanium Oxide Support Controls Activity and Selectivity in Methanol Oxidation on Platinum

KAUST Repository

Hervier, Antoine

2011-11-24

Platinum films of 1 nm thickness were deposited by electron beam evaporation onto 100 nm thick titanium oxide films (TiOx) with variable oxygen vacancy concentrations and fluorine (F) doping. Methanol oxidation on the platinum films produced formaldehyde, methyl formate, and carbon dioxide. F-doped samples demonstrated significantly higher activity for methanol oxidation when the TiOx was stoichiometric (TiO 2), but lower activity when it was nonstoichiometric (TiO 1.7 and TiO1.9). These results correlate with the chemical behavior of the same types of catalysts in CO oxidation. Fluorine doping of stoichiometric TiO2 also increased selectivity toward partial oxidation of methanol to formaldehyde and methyl formate, but had an opposite effect in the case of nonstoichiometric TiOx. Introduction of oxygen vacancies and fluorine doping both increased the conductivity of the TiO x film. For oxygen vacancies, this occurred by the formation of a conduction channel in the band gap, whereas in the case of fluorine doping, F acted as an n-type donor, forming a conduction channel at the bottom of the conduction band, about 0.5-1.0 eV higher in energy. The higher energy electrons in F-doped stoichiometric TiOx led to higher turnover rates and increased selectivity toward partial oxidation of methanol. This correlation between electronic structure and turnover rate and selectivity indicates that the ability of the support to transfer charges to surface species controls in part the activity and selectivity of the reaction. © 2011 American Chemical Society.

GLUT1-mediated selective tumor targeting with fluorine containing platinum(II) glycoconjugates.

Science.gov (United States)

Liu, Ran; Fu, Zheng; Zhao, Meng; Gao, Xiangqian; Li, Hong; Mi, Qian; Liu, Pengxing; Yang, Jinna; Yao, Zhi; Gao, Qingzhi

2017-06-13

Increased glycolysis and overexpression of glucose transporters (GLUTs) are physiological characteristics of human malignancies. Based on the so-called Warburg effect, 18flurodeoxyglucose-positron emission tomography (FDG-PET) has successfully developed as clinical modality for the diagnosis and staging of many cancers. To leverage this glucose transporter mediated metabolic disparity between normal and malignant cells, in the current report, we focus on the fluorine substituted series of glucose, mannose and galactose-conjugated (trans-R,R-cyclohexane-1,2-diamine)-2-flouromalonato-platinum(II) complexes for a comprehensive evaluation on their selective tumor targeting. Besides highly improved water solubility, these sugar-conjugates presented improved cytotoxicity than oxaliplatin in glucose tranporters (GLUTs) overexpressing cancer cell lines and exhibited no cross-resistance to cisplatin. For the highly water soluble glucose-conjugated complex (5a), two novel in vivo assessments were conducted and the results revealed that 5a was more efficacious at a lower equitoxic dose (70% MTD) than oxaliplatin (100% MTD) in HT29 xenograft model, and it was significantly more potent than oxaliplatin in leukemia-bearing DBA/2 mice as well even at equimolar dose levels (18% vs 90% MTD). GLUT inhibitor mediated cell viability analysis, GLUT1 knockdown cell line-based cytotoxicity evaluation, and platinum accumulation study demonstrated that the cellular uptake of the sugar-conjugates was regulated by GLUT1. The higher intrinsic DNA reactivity of the sugar-conjugates was confirmed by kinetic study of platinum(II)-guanosine adduct formation. The mechanistic origin of the antitumor effect of the fluorine complexes was found to be forming the bifunctional Pt-guanine-guanine (Pt-GG) intrastrand cross-links with DNA. The results provide a rationale for Warburg effect targeted anticancer drug design.

Ergonomics of locomotive design in South African Gold and Platinum mines.

CSIR Research Space (South Africa)

Smith, JR

2002-03-01

Full Text Available to determine reach, posture, field of view and control locations for the operator. • determining the design modifications, which would improve the overall operation of the mine locomotives in South African gold and platinum mines • formu... Acknowledgements Invaluable contributions from the following people are acknowledged: Mr J Annandale Impala Platinum Ltd., Shaft No. 1 Mr W Birmingham Joel Gold Mining Company Ltd. Mr W Brits Anglogold Ltd., Savuka Mine Mr G Burger Anglogold Ltd, West Wits...

Concentrations of Platinum Group Elements (Pt, Pd, Rh in Airborne Particulate Matter (PM2.5 and PM10-2.5 Collected at Selected Canadian Urban Sites: a Case Study

Directory of Open Access Journals (Sweden)

Celo V.

2013-04-01

Full Text Available Increasing environmental concentrations of platinum group elements (PGEs, in particular platinum (Pt, palladium (Pd and rhodium (Rh, from catalytic converters has been reported worldwide. Initially it was believed that the emitted PGEs remain in the roadside environment, but recent studies have shown that fine PGE-containing particles can be transported and distributed at regional and long-range levels. Therefore, the monitoring of PGEs in airborne particulate matter (PM is important for the estimation of potential risks to human health and to the ecosystem. The aim of this study is to present the first results from an analysis on the concentration and distribution of Pt, Pd and Rh in PM collected on Teflon filters at two selected urban sites (Toronto, Ontario; Edmonton, Alberta collected within the Canadian National Air Pollution Surveillance (NAPS network. In this work, a quadruple inductively coupled plasma mass spectrometry (ICP-MS, combined with microwave assisted acid digestion using aqua regia was used. A cation exchange separation was used to alleviate the matrix-induced spectral and nonspectral interferences prior to ICP-MS analysis. To obtain sufficient material needed for PGEs analysis, fine PM (particles with aerodynamic diameter less than 2.5 mm; PM2.5 and coarse PM (with aerodynamic diameter between 2.5 and 10 mm; PM10-2.5 samples were combined into composite samples on a seasonal basis. The obtained results will be discussed and compared with literature data.

(Acetylacetonato-κ2O,O′bis[5-methoxy-2-(naphth[1,2-d][1,3]oxazol-2-ylphenyl-κ2C1,N]iridium(III

Directory of Open Access Journals (Sweden)

Yuan-Yuan Zhou

2011-10-01

Full Text Available In the title compound, [Ir(C18H12NO22(C5H7O2], the Ir atom is O,O′-chelated by the acetylacetonate group and C,N-chelated by the 2-arylnaphth[1,2-d]oxazole groups. The six-coordinate metal atom displays a distorted octahedral geometry. Intramolecular C—H...O hydrogen bonds occur. In the crystal, intermolecular C—H...O hydrogen bonds link the molecules into columns parallel to the b axis.

Femtosecond laser-induced periodic surface nanostructuring of sputtered platinum thin films

Energy Technology Data Exchange (ETDEWEB)

Rodríguez, Ainara, E-mail: airodriguez@ceit.es [CIC microGUNE, Goiru Kalea 9 Polo Innovación Garaia, 20500 Arrasate-Mondragón (Spain); CEIT-IK4 & Tecnun (University of Navarra), Paseo Manuel Lardizábal 15, 20018 San Sebastián (Spain); Morant-Miñana, Maria Carmen; Dias-Ponte, Antonio; Martínez-Calderón, Miguel; Gómez-Aranzadi, Mikel; Olaizola, Santiago M. [CIC microGUNE, Goiru Kalea 9 Polo Innovación Garaia, 20500 Arrasate-Mondragón (Spain); CEIT-IK4 & Tecnun (University of Navarra), Paseo Manuel Lardizábal 15, 20018 San Sebastián (Spain)

2015-10-01

Highlights: • Femtosecond laser-induced surface nanostructures on sputtered platinum thin films. • Three types of structures obtained: random nanostructures, LSFL and HSFL. • Two different modification regimes have been established based on laser fluence. - Abstract: In this work, submicro and nanostructures self-formed on the surface of Platinum thin films under femtosecond laser-pulse irradiation are investigated. A Ti:Sapphire laser system was used to linearly scan 15 mm lines with 100 fs pulses at a central wavelength of 800 nm with a 1 kHz repetition rate. The resulting structures were characterized by scanning electron microscopy (SEM) and 2D-Fast Fourier Transform (2D-FFT) analysis. This analysis of images revealed different types of structures depending on the laser irradiation parameters: random nanostructures, low spatial frequency LIPSS (LSFL) with a periodicity from about 450 to 600 nm, and high spatial frequency LIPSS (HSFL) with a periodicity from about 80 to 200 nm. Two different modifications regimes have been established for the formation of nanostructures: (a) a high-fluence regime in which random nanostructures and LSFL are obtained and (b) a low-fluence regime in which HSFL and LSFL are obtained.

Mechanooptic Regulation of Photoconduction in Functionalized Carbon Nanotubes Decorated with Platinum

Directory of Open Access Journals (Sweden)

C. Mercado-Zúñiga

2014-01-01

Full Text Available The observation of photoconduction and nonlinear optical absorption on functionalized multiwall carbon nanotubes decorated with platinum is reported. The samples were prepared by a chemical vapor deposition method. The electrical conductivity of the carbon nanotubes seems to be decreased by the functionalization process; but this property is strongly enhanced after the incorporation of platinum particles. Nonresonant photoconductive experiments at 532 nm and 445 nm wavelengths allow us to detect a selective participation of the platinum to the photoelectrical response. A mechanooptic effect based on Fresnel reflection was obtained through a photoconductive modulation induced by the rotation of a silica substrate where the samples were deposited as a thin film. A two-photon absorption process was identified as the main physical mechanism responsible for the nonlinear optical absorption. We consider that important changes in the nonlinear photon interactions with carbon nanotubes can be related to the population losses derived from phonons and the detuning of the frequency originated by functionalization.

A sensitivity study of the oxidation of compressed natural gas on platinum

KAUST Repository

Badra, Jihad

2013-11-01

This paper presents a sensitivity study for the oxidation of methane (CH4) over platinum (Pt). Some dominant reactions in the CH 4-Pt surface chemistry were identified and the rates of these reactions were subsequently modified to enhance the calculations. Initially, a range of CH4-Pt surface mechanisms available in the literature are used, along with the relevant detailed gaseous chemistry to compute the structure of premixed compressed natural gas (CNG)/air flames co-flowing around a flat, vertical, unconfined, rectangular, and platinum plate. Comparison with existing measurements of surface temperature and species concentrations revealed significant discrepancies for all mechanisms. Sensitivity analysis has identified nine key reactions which dominate the heterogeneous chemistry of methane over platinum. The rates of these reactions were modified over a reasonable range and in different combinations leading to an "optimal" mechanism for methane/air surface chemistry on platinum. The new mechanism is then used with the same flow geometry for different cases varying the temperature of the incoming mixture (Tjet), its equivalence ratio (Φ) and the Reynolds number (Re). Results from the modified surface mechanism demonstrate reasonably good agreement with the experimental data for a wide range of operating conditions. © 2013 Elsevier Ltd. All rights reserved.

Comparison of platinum/MWCNTs Nanocatalysts Synthesis Processes for Proton Exchange Membrane Fuel Cells

Science.gov (United States)

Liu, Xuan

Due to the growing concerns on the depletion of petroleum based energy resources and climate change; fuel cell technologies have received much attention in recent years. Proton exchange membrane fuel cell (PEMFCs) features high energy conversion efficiency and nearly zero greenhouse gas emissions, because of its combination of the hydrogen oxidation reaction (HOR) at anode side and oxygen reduction reaction (ORR) at cathode side. Synthesis of Pt nanoparticles supported on multi walled carbon nanotubes (MWCNTs) possess a highly durable electrochemical surface area (ESA) and show good power output on proton exchange membrane (PEM) fuel cell performance. Platinum on multi-walled carbon nanotubes (MWCNTs) support were synthesized by two different processes to transfer PtCl62- from aqueous to organic phase. While the first method of Pt/MWCNTs synthesis involved dodecane thiol (DDT) and octadecane thiol (ODT) as anchoring agent, the second method used ammonium lauryl sulfate (ALS) as the dispersion/anchoring agent. The particle size and distribution of platinum were examined by high-resolution transmission electron microscope (HRTEM). The TEM images showed homogenous distribution and uniform particle size of platinum deposited on the surface of MWCNTs. The single cell fuel cell performance of the Pt/MWCNTs synthesized thiols and ALS based electrode containing 0.2 (anode) and 0.4 mg (cathode) Pt.cm-2 were evaluated using Nafion-212 electrolyte with H2 and O2 gases at 80 °C and ambient pressure. The catalyst synthesis with ALS is relatively simple compared to that with thiols and also showed higher performance (power density reaches about 1070 mW.cm -2). The Electrodes with Pt/MWCNTs nanocatalysts synthesized using ALS were characterized by cyclic voltammetry (CV) for durability evaluation using humidified H2 and N2 gases at room temperature (21 °C) along with commercial Pt/C for comparison. The ESA measured by cyclic voltammetry between 0.15 and 1.2 V showed significant

Analysis of damaged DNA / proteins interactions: Methodological optimizations and applications to DNA lesions induced by platinum anticancer drugs

International Nuclear Information System (INIS)

Bounaix Morand du Puch, Ch

2010-10-01

DNA lesions contribute to the alteration of DNA structure, thereby inhibiting essential cellular processes. Such alterations may be beneficial for chemotherapies, for example in the case of platinum anticancer agents. They generate bulky adducts that, if not repaired, ultimately cause apoptosis. A better understanding of the biological response to such molecules can be obtained through the study of proteins that directly interact with the damages. These proteins constitute the DNA lesions interactome. This thesis presents the development of tools aiming at increasing the list of platinum adduct-associated proteins. Firstly, we designed a ligand fishing system made of damaged plasmids immobilized onto magnetic beads. Three platinum drugs were selected for our study: cisplatin, oxali-platin and satra-platin. Following exposure of the trap to nuclear extracts from HeLa cancer cells and identification of retained proteins by proteomics, we obtained already known candidates (HMGB1, hUBF, FACT complex) but also 29 new members of the platinated-DNA interactome. Among them, we noted the presence of PNUTS, TOX4 and WDR82, which associate to form the recently-discovered PTW/PP complex. Their capture was then confirmed with a second model, namely breast cancer cell line MDA MB 231, and the biological consequences of such an interaction now need to be elucidated. Secondly, we adapted a SPRi bio-chip to the study of platinum-damaged DNA/proteins interactions. Affinity of HMGB1 and newly characterized TOX4 for adducts generated by our three platinum drugs could be validated thanks to the bio-chip. Finally, we used our tools, as well as analytical chemistry and biochemistry methods, to evaluate the role of DDB2 (a factor involved in the recognition of UV-induced lesions) in the repair of cisplatin adducts. Our experiments using MDA MB 231 cells differentially expressing DDB2 showed that this protein is not responsible for the repair of platinum damages. Instead, it appears to act

Platinum nanoparticles decorated dendrite-like gold nanostructure on glassy carbon electrodes for enhancing electrocatalysis performance to glucose oxidation

Energy Technology Data Exchange (ETDEWEB)

Jia, Hongmei [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, School of Materials Science and Engineering, Hubei University, No. 368 Youyi Avenue, Wuchang, Wuhan 430062 (China); Chang, Gang, E-mail: changgang@hubu.edu.cn [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, School of Materials Science and Engineering, Hubei University, No. 368 Youyi Avenue, Wuchang, Wuhan 430062 (China); Lei, Ming [State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876 (China); He, Hanping [College of Chemistry and Chemical Engineer, Hubei University, Youyi Road 368, Wuchang, Wuhan, Hubei 430062 (China); Liu, Xiong; Shu, Honghui; Xia, Tiantian; Su, Jie [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, School of Materials Science and Engineering, Hubei University, No. 368 Youyi Avenue, Wuchang, Wuhan 430062 (China); He, Yunbin, E-mail: ybhe@hubu.edu.cn [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Ministry-of-Education Key Laboratory for the Green Preparation and Application of Functional Materials, School of Materials Science and Engineering, Hubei University, No. 368 Youyi Avenue, Wuchang, Wuhan 430062 (China)

2016-10-30

oxidation of glucose because of excellent synergetic effects between gold and platinum species and the increased electrochemical active area from Pt nanoparticles loading. The non-enzymatic glucose biosensor based on Pt/DGNs/GC showed a rapid respond time (within 2 s), wide linear range (from 0.1 mM to 14 mM), low detection limit (0.01 mM), supernal sensitivity (275.44 μA cm{sup −2} mM{sup −1}, R = 0.993), satisfactory reproducibility and good stability for glucose sensing. It was demonstrated that Pt/DGNs/GC could work as promising candidate for factual non-enzymatic glucose detection.

Teaching - methodical and research center of hydrogen power engineering and platinum group metals in the former Soviet Union countries

International Nuclear Information System (INIS)

Evdokimov, A.A; Sigov, A.S; Shinkarenko, V.V.

2005-01-01

Full text: Teaching - Methodical and Research Center (TMRC) 'Sokolinaja Gora' is founded in order to provide methodical-information and scientific support of institutes of higher education in the field of hydrogen power engineering and platinum group metals in Russia and in the countries of the Former Soviet union. It is independent association of creative communities of scientist of higher educational specialists. The main directions of the Center activity are: 1. Teaching-methodological support and development of teaching in the field of hydrogen power engineering and platinum group metals in Russia in the countries of the Former Soviet Union. Themes of teaching includes the basic of safe using of hydrogen technologies and devices, ecological, economic and law aspects of new hydrogen power engineering, transition to which in 21 century is one of the central problems of mankind survival; 2. Organizing of joint researches by independent creative communities of scientists in the field of hydrogen power engineering and platinum group metal; 3. Independent scientific examination, which is made by Advisory Committee of High Technologies consisting of representatives of the countries of Former Soviet Union, which are standing participants of an Annual International Symposia 'Hydrogen Power Engineering and Platinum Group Metals in the Former Soviet Union Countries'. Structure of the Center: 1. Center of strategic development in the field of high technologies; 2. Scientific Research Institute of Hydrogen Power Engineering and Platinum Group Metals; 3. Teaching-Methodical Association in specialization 'Hydrogen Power Engineering and economics' and hydrogen wide spread training; 4. Media Center 'Hydrogen Power Engineering and Platinum Group Metals', 5. Organizational Center; 6. Administrative Center. The Center will be established step-by-step in 2005-2010 on the basis of the following programs: Teaching-methodological program. On the basis of this program it is planned to

CECs and IL-8 Have Prognostic and Predictive Utility in Patients with Recurrent Platinum-Sensitive Ovarian Cancer: Biomarker Correlates from the Randomized Phase-2 Trial of Olaparib and Cediranib Compared with Olaparib in Recurrent Platinum-Sensitive Ovarian Cancer.

Science.gov (United States)

Lee, Jung-Min; Trepel, Jane B; Choyke, Peter; Cao, Liang; Sissung, Tristan; Houston, Nicole; Yu, Minshu; Figg, William D; Turkbey, Ismail Baris; Steinberg, Seth M; Lee, Min-Jung; Ivy, S Percy; Liu, Joyce F; Matulonis, Ursula A; Kohn, Elise C

2015-01-01

Olaparib (O), a polyADPribose polymerase (PARP) inhibitor, and cediranib (C), a VEGF receptor (VEGFR)1-3 inhibitor together had greater activity than O alone in women with recurrent platinum-sensitive ovarian cancer (OvCa). The objective of this study is to identify potential lead biomarker candidates for response to O + C in the setting of a multi-institutional phase II study of O with and without C in recurrent platinum-sensitive OvCa. A self-selected group of patients participated in a prospectively planned exploratory biomarker substudy of the randomized phase II study of O versus O + C. Whole blood for peripheral blood mononuclear cell (PBMC) and plasma isolation was collected prior to and on day 3 of treatment. Quantitation of circulating endothelial cells (CEC), IL-6, IL-8, VEGF, and soluble VEGFR-2 plasma concentrations, and polyADPribose (PAR) incorporation were performed. Single nucleotide polymorphism analysis of XRCC1 280H, R194W, and Q399R was done. Dynamic contrast-enhanced-magnetic resonance imaging (DCE-MRI) was performed at baseline and day 3 of treatment. Parameter changes were compared between the two arms using an exact Wilcoxon rank sum test. Kaplan-Meier and log-rank tests were used to examine survival outcome. Thirteen patients elected to participate in the translational substudy, seven patients on O and six patients on O + C. Patients on O + C had a greater decrease in IL-8 concentration and larger CEC fold increase compared with those on O alone (p = 0.026, p = 0.032). The fold increase in CEC on day 3 was associated with duration of progression-free survival (PFS) (R (2) = 0.77, 95% CI 0.55-0.97, p < 0.001). IL-8 post-pretreatment changes correlate with PFS (p = 0.028). XRCC1 DNA polymorphisms were not related to PFS. All patients had reduction in PAR incorporation, and all except one had reduction in vascular flow on DCE-MRI. Our exploratory correlative studies indicate that CEC and IL-8 changes may be

Meta-Analysis on Pharmacogenetics of Platinum-Based Chemotherapy in Non Small Cell Lung Cancer (NSCLC) Patients

Science.gov (United States)

Yin, Ji-Ye; Huang, Qiong; Zhao, Ying-Chun; Zhou, Hong-Hao; Liu, Zhao-Qian

2012-01-01

Aim To determine the pharmacogenetics of platinum-based chemotherapy in Non Small Cell Lung Cancer (NSCLC) patients. Methods Publications were selected from PubMed, Cochrane Library and ISI Web of Knowledge. A meta-analysis was conducted to determine the association between genetic polymorphisms and platinum-based chemotherapy by checking odds ratio (OR) and 95% confidence interval (CI). Results Data were extracted from 24 publications, which included 11 polymorphisms in 8 genes for meta-analysis. MDR1 C3435T (OR = 1.97, 95% CI: 1.11–3.50, P = 0.02), G2677A/T (OR = 2.61, 95% CI: 1.44–4.74, P = 0.002) and GSTP1 A313G (OR = 0.32, 95% CI: 0.17–0.58, P = 0.0002) were significantly correlated with platinum-based chemotherapy in Asian NSCLC patients. Conclusion Attention should be paid to MDR1 C3435T, G2677A/T and GSTP1 A313G for personalized chemotherapy treatment for NSCLC patients in Asian population in the future. PMID:22761669

Impurities determination in precious metals like rhodium, palladium and platinum by neutron activation without separation

International Nuclear Information System (INIS)

May, S.; Piccot, D.; Pinte, G.

1978-01-01

The possibilities of the method explored using an installation of gamma or X ray spectrometry of good performance. The irradiations were realized in the reactors EL.3 (flux approximately 6.10 12 n.cm -2 .s -1 ) and Osiris (flux > 10 14 n.cm -2 .s -1 ) of the CEN Saclay. In rhodium the presence of iridium limits the analysis possibilities. However gold, silver and platinum are easily determined, just as the other elements (As, Br, Cl, Co, Mn, Na, Sb). In platinum it is possible to determine the elements of long period, especially antimony, silver, cobalt, iridium, tantalum and zinc. As for palladium the principal impurities are gold, silver and ruthenium for what is of precious metals and particularly zinc among the other metals. For the three matrices considered the detection limits of a certain number of elements are indicated [fr

Formation of carbonato and hydroxo complexes in the reaction of platinum anticancer drugs with carbonate.

Science.gov (United States)

Di Pasqua, Anthony J; Centerwall, Corey R; Kerwood, Deborah J; Dabrowiak, James C

2009-02-02

The second-generation Pt(II) anticancer drug carboplatin is here shown to react with carbonate, which is present in blood, interstitial fluid, cytosol, and culture medium, to produce platinum-carbonato and -hydroxo complexes. Using [(1)H-(15)N] HSQC NMR and (15)N-labeled carboplatin, we observe that cis-[Pt(CBDCA-O)(OH)(NH(3))(2)](-), cis-[Pt(OH)(2)(NH(3))(2)], cis-[Pt(CO(3))(OH)(NH(3))(2)](-), and what may be cis-[Pt(CO(3))(NH(3))(2)] are produced when 1 is allowed to react in 23.8 mM carbonate buffer. When (15)N-labeled carboplatin is allowed to react in 0.5 M carbonate buffer, these platinum species, as well as other hydroxo and carbonato species, some of which may be dinuclear complexes, are produced. Furthermore, we show that the carbonato species cis-[Pt(CO(3))(OH)(NH(3))(2)](-) is also produced when cisplatin is allowed to react in carbonate buffer. The study outlines the conditions under which carboplatin and cisplatin form carbonato and aqua/hydroxo species in carbonate media.

Nanoengineering of Ruthenium and Platinum-based Nanocatalysts by Continuous-Flow Chemistry for Renewable Energy Applications

KAUST Repository

AlYami, Noktan Mohammed

2017-04-15

This thesis presents an integrated study of nanocatalysts for heterogenous catalytic and electrochemical processes using pure ruthenium (Ru) with mixed-phase and platinum-based nanomaterials synthesized by continuous-flow chemistry. There are three major challenges to the application of nanomaterials in heterogenous catalytic reactions and electrocatalytic processes in acidic solution. These challenges are the following: (i) controlling the size, shape and crystallography of nanoparticles to give the best catalytic properties, (ii) scaling these nanoparticles up to a commercial quantity (kg per day) and (iii) making stable nanoparticles that can be used catalytically without degrading in acidic electrolytes. Some crucial limitations of these nanostructured materials in energy conversion and storage applications were overcome by continuous-flow chemistry. By using a continuous-flow reactor, the creation of scalable nanoparticle systems was achieved and their functionality was modified to control the nanoparticles’ physical and chemical characteristics. The nanoparticles were also tested for long-term stability, to make sure these nanoparticles were feasible under realistic working conditions. These nanoparticles are (1) shape- and crystallography-controlled ruthenium (Ru) nanoparticles, (2) size-controlled platinum-metal (Pt-M= nickel (Ni) & copper (Cu)) nanooctahedra (while maintaining morphology) and (3) core-shell platinum@ruthenium (Pt@Ru) nanoparticles where an ultrathin ruthenium shell was templated onto the platinum core. Thus, a complete experimental validation of the formation of a scalable amount of these nanoparticles and their catalytic activity and stability towards the oxygen evolution reaction (OER) in acid medium, hydrolysis of ammonia borane (AB) along with plausible explanations were provided.

Sequential Electrodeposition of Platinum-Ruthenium at Boron-Doped Diamond Electrodes for Methanol Oxidation

Directory of Open Access Journals (Sweden)

Ileana González-González

2011-01-01

Full Text Available Sequential electrodeposition of Pt and Ru on boron-doped diamond (BDD films, in 0.5 M H2SO4 by cyclic voltammetry, has been prepared. The potential cycling, in the aqueous solutions of the respective metals, was between 0.00 and 1.00 V versus Ag/AgCl. The catalyst composites, Pt and PtRu, deposited on BDD film substrates, were tested for methanol oxidation. The modified diamond surfaces were also characterized by scanning electron microscopy-X-ray fluorescence-energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and Auger electron spectroscopy. The scanning Auger electron spectroscopy mapping showed the ruthenium signal only in areas where platinum was electrodeposited. Ruthenium does not deposit on the oxidized diamond surface of the boron-doped diamond. Particles with 5–10% of ruthenium with respect to platinum exhibited better performance for methanol oxidation in terms of methanol oxidation peak current and chronoamperometric current stability. The electrogenerated •OH radicals on BDD may interact with Pt surface, participating in the methanol oxidation as shown in oxidation current and the shift in the peak position. The conductive diamond surface is a good candidate as the support for the platinum electrocatalyst, because it ensures catalytic activity, which compares with the used carbon, and higher stability under severe anodic and cathodic conditions.

Invited: Tailoring Platinum Group Metals Towards Optimal Activity for Oxygen Electroreduction to H2o and H2O2: From Extended Surfaces to Nanoparticles

DEFF Research Database (Denmark)

Stephens, Ifan

2014-01-01

). The figure shows transmission electron miscroscopy images of 9 nm diameter PtxY nanoparticles, based on high angle annular dark field –scanning transmission electron microscopy (left) and Y, Pt and combined Pt+Y X-ray energy dispersive X-ray spectroscopy elemental maps. (a) as-prepared catalyst and (b) after......The slow kinetics of the 4-electron reduction of oxygen to H2O imposes a bottleneck against the widespread uptake of low temperature fuel cells in automotive vehicles. High loadings of platinum are required to drive the reaction; the limited supply of this precious metal limits the extent to which...... fuel cell technology could be scaled up.(1) The most widely used strategy towards decreasing the Pt loading is to alloy Pt with other late transition metals, in particular Ni or Co. (2-5) However, when tested in a fuel cell, these alloys are often susceptible towards degradation via dealloying.(6, 7...

ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, HVLP COATING EQUIPMENT, SHARPE MANUFACTURING COMPANY PLATINUM 2012 HVLP SPRAY GUN

Science.gov (United States)

This report presents the results of the verification test of the Sharpe Platinum 2013 high-volume, low-pressure gravity-feed spray gun, hereafter referred to as the Sharpe Platinum, which is designed for use in automotive refinishing. The test coating chosen by Sharpe Manufacturi...

Synthesis and properties of platinum on multiwall carbon nanotube modified by chitosan

Science.gov (United States)

Fikriyyah, A. K.; Chaldun, E. R.; Indriyati

2018-03-01

Platinum nanoparticles on multiwall carbon nanotubes (Pt/MWCNT) play an important role in fuel cell to convert the chemical energy from a fuel into electricity. In this study, Pt/MWCNT electrocatalysts were prepared by chemical reduction of the metal salts in chitosan as the support. Firstly, commercial MWCNTs were functionalized by oxidative process using a mixture of nitric acid and sulfuric acid. Then, functionalized MWCNTs were mixed with chitosan-acetic acid solution to conduct grafting reaction with NH2 groups in chitosan by solution polymerization method. Platinum nanoparticles were loaded onto the surface of the MWCNTs after hexachloroplatinic acid was reduced by sodium hydroxide solution. The result showed that Pt was attached on MWCNT based on analysis from EDS, XRD, and UV Vis Spectroscopy. UV Vis analysis indicates the plasmon absorbance band of Pt nanoparticles in Pt/MWCNT, while XRD analysis confirmed the size of Pt particle in nanometer. This elucidates the potential procedure to synthesize Pt/MWCNT using chitosan.

di Synthesis and Characterization of the Platinum-Substituted Keggin Anion alpha-H2SiPtW11O404-

Energy Technology Data Exchange (ETDEWEB)

Klonowski, P; Goloboy, JC; Uribe-Romo, FJ; Sun, FR; Zhu, LY; Gandara, F; Wills, C; Errington, RJ; Yaghi, OM; Klemperer, WG

2014-12-15

Acidification of an aqueous solution of K8SiW11O39 and K2Pt(OH)(6) to pH 4 followed by addition of excess tetramethylammonium (TMA) chloride yielded a solid mixture of TMA salts of H2SiPtW11O404- (1) and SiW12O404- (2). The former was separated from the latter by extraction into an aqueous solution and converted into tetra-n-butylammonium (TBA) and potassium salts TBA-1 and K-1. The a-H2SiPtW11O404- was identified as a monosubstituted Keggin anion using elemental analysis, IR spectroscopy, X-ray crystallography, electrospray ionization mass spectrometry, Pt-195 NMR spectroscopy, (183)W NMR spectroscopy, and W-183-W-183 2D INADEQUATE NMR spectroscopy. Both TBA-1 and K-1 readily cocrystallized with their unsubstituted Keggin anion salts, TBA-2 and K-2, respectively, providing an explanation for the historical difficulty of isolating certain platinum-substituted heteropolyanions in pure form.

Design, synthesis and anticancer activity of diam(m)ine platinum(II) complexes bearing a small-molecular cell apoptosis inducer dichloroacetate.

Science.gov (United States)

Liu, Weiping; Jiang, Jing; Xu, Yongping; Hou, Shuqian; Sun, Liping; Ye, Qingsong; Lou, Liguang

2015-05-01

Four new diam(m)ine platinum complexes containing the dichloroacetate moiety in 3-dichoroacetoxylcyclobutane-1,1-dicarboxylate as the leaving group were synthesized, characterized by elemental analysis as well as by ESI(+)-MS (electrospray ionization mass spectrometry in positive mode), FT-IR, (1)H- and (13)C-NMR, and evaluated for their in vitro anticancer activity against human lung cancer cell line (A549) and ovarian cancer cell lines (SK-OV-3, SK-OV-3/DDP). Diam(m)ines used in the present study belong to the carriers of six clinically approved platinum drugs. Among the complexes synthesized, complex 2, cis-[Pt(II)(1R,2R-diaminocyclohexane)·(3-dichoroacetoxylcyclobutane-1,1-dicarboxylate)] is the most promising in terms of water solubility and potential of being totally devoid of cross-drug resistance with cisplatin. Therefore, complex 2 was selected for the dichloroacetate release test. The test shows dichloroacetate can be efficiently released from complex 2 under physiological conditions via the hydrolysis of an ester bond bridging the dichloroacetate moiety and platinum pharmacophores together. Our study supports the further evaluation of this complex as a drug candidate. Copyright © 2015 Elsevier Inc. All rights reserved.

S-1 monotherapy for recurrent or metastatic squamous cell carcinoma of the head and neck after progression on platinum-based chemotherapy

International Nuclear Information System (INIS)

Yokota, Tomoya; Onozawa, Yusuke; Boku, Narikazu

2011-01-01

Platinum compounds play pivotal roles in treatment for squamous cell carcinoma of the head and neck. The objective was to evaluate the efficacy of S-1 monotherapy in patients with recurrent or metastatic squamous cell carcinoma of the head and neck after failure of platinum-based chemotherapy. We retrospectively analyzed 39 consecutive patients with recurrent or metastatic squamous cell carcinoma of the head and neck who received S-1 monotherapy after failure of platinum-based chemotherapy or chemoradiotherapy at the Shizuoka Cancer Center between August 2003 and October 2010. S-1 was given orally twice daily (80 mg/m 2 /day) for 28 days followed by a 14-day rest. The median follow-up period in survivors was 31.5 months. Among 38 patients with measurable lesions, 9 (24%) showed partial response and 15 (39%) showed stable disease. The median progression-free survival was 4.9 months and the median overall survival was 13.2 months. The median progression-free survival for oropharyngeal cancer (n=7) was significantly longer than for other cancers (n=32) (14.9 vs. 4.7 months, P=0.035). The response rate in patients with a recurrence-free interval since the last platinum administration >6.0 months was significantly better than with a recurrence-free interval 6.0 months also showed a significantly better progression-free survival (6.0 vs. 2.6 months, P=0.045). The frequency of Grade 3/4 toxicities was less than 10%. S-1 monotherapy shows promising signs of efficacy and tolerability in patients with recurrent or metastatic squamous cell carcinoma of the head and neck after failure of platinum-based chemotherapy in this retrospective cohort and warrants further investigation in this population. (author)

The impact of whole human blood on the kinetic inertness of platinum(iv) prodrugs - an HPLC-ICP-MS study.

Science.gov (United States)

Theiner, Sarah; Grabarics, Márkó; Galvez, Luis; Varbanov, Hristo P; Sommerfeld, Nadine S; Galanski, Markus; Keppler, Bernhard K; Koellensperger, Gunda

2018-04-17

The potential advantage of platinum(iv) complexes as alternatives to classical platinum(ii)-based drugs relies on their kinetic stability in the body before reaching the tumor site and on their activation by reduction inside cancer cells. In this study, an analytical workflow has been developed to investigate the reductive biotransformation and kinetic inertness of platinum(iv) prodrugs comprising different ligand coordination spheres (respectively, lipophilicity and redox behavior) in whole human blood. The distribution of platinum(iv) complexes in blood pellets and plasma was determined by inductively coupled plasma-mass spectrometry (ICP-MS) after microwave digestion. An analytical approach based on reversed-phase (RP)-ICP-MS was used to monitor the parent compound and the formation of metabolites using two different extraction procedures. The ligand coordination sphere of the platinum(iv) complexes had a significant impact on their accumulation in red blood cells and on their degree of kinetic inertness in whole human blood. The most lipophilic platinum(iv) compound featuring equatorial chlorido ligands showed a pronounced penetration into blood cells and a rapid reductive biotransformation. In contrast, the more hydrophilic platinum(iv) complexes with a carboplatin- and oxaliplatin-core exerted kinetic inertness on a pharmacologically relevant time scale with notable amounts of the compound accumulated in the plasma fraction.

Green synthesis and characterisation of platinum nanoparticles using quail egg yolk

Science.gov (United States)

Nadaroglu, Hayrunnisa; Gungor, Azize Alayli; Ince, Selvi; Babagil, Aynur

2017-02-01

Nanotechnology is extensively used in all parts today. Therefore, nano synthesis is also significant in all explored areas. The results of studies conducted have revealed that nanoparticle synthesis is performed by using both chemical and physical methods. It is well known that these syntheses are carried out at high charge, pressure and temperature in harsh environments. Therefore, this study investigated green synthesis method that sustains more mild conditions. In this study, quail egg yolk having high vitamin and protein content was prepared for green synthesis reaction and used for the synthesis of platinum nanoparticles in the reaction medium. Reaction situations were optimised as a function of pH, temperature, time and concentration by using quail egg yolk. The results showed that the highest platinum nanoparticles were synthesised at 20 °C and pH 6.0 for 4 h. Also, optimal concentration of metal ions was established as 0.5 mM. The synthesised platinum nanoparticles were characterised by using UV spectrum, X-ray diffraction and scanning electron microscope.

Dye sensitized solar cell based on platinum decorated multiwall carbon nanotubes as catalytic layer on the counter electrode

International Nuclear Information System (INIS)

Mathew, Ambily; Rao, G. Mohan; Munichandraiah, N.

2011-01-01

Graphical abstract: I-V characteristics of the DSSCs with Pt CE and Pt/MWCNT CE measured at 100 mW/cm 2 . It shows relatively better performance with Pt/MWCNT counter electrodes. Highlights: → Synthesis of multiwalled carbon nanotubes by pyrolysis. → Synthesis of Pt/MWCNT composite by chemical reduction. → Fabrication DSSC using Pt/MWCNT as catalytic layer on the counter electrode. → Study of catalytic activity by Electrochemical Impedance Spectroscopy. -- Abstract: In this study we have employed multiwall carbon nanotubes (MWCNT), decorated with platinum as catalytic layer for the reduction of tri-iodide ions in dye sensitized solar cell (DSSC). MWCNTs have been prepared by a simple one step pyrolysis method using ferrocene as the catalyst and xylene as the carbon source. Platinum decorated MWCNTs have been prepared by chemical reduction method. The as prepared MWCNTs and Pt/MWCNTs have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In combination with a dye adsorbed TiO 2 photoanode and an organic liquid electrolyte, Pt/MWCNT composite showed an enhanced short circuit current density of 16.12 mA/cm 2 leading to a cell efficiency of 6.50% which is comparable to that of Platinum.

Dye sensitized solar cell based on platinum decorated multiwall carbon nanotubes as catalytic layer on the counter electrode

Energy Technology Data Exchange (ETDEWEB)

Mathew, Ambily [Department of Instrumentation and Applied Physics, Indian Institute of Science, Bangalore 560012 India (India); Rao, G. Mohan, E-mail: gmrao@isu.iisc.ernet.in [Department of Instrumentation and Applied Physics, Indian Institute of Science, Bangalore 560012 India (India); Munichandraiah, N. [Department of Inorgonic and Physical Chemistry, Indian Institute of Science, Bangalore 560012 India (India)

2011-11-15

Graphical abstract: I-V characteristics of the DSSCs with Pt CE and Pt/MWCNT CE measured at 100 mW/cm{sup 2}. It shows relatively better performance with Pt/MWCNT counter electrodes. Highlights: {yields} Synthesis of multiwalled carbon nanotubes by pyrolysis. {yields} Synthesis of Pt/MWCNT composite by chemical reduction. {yields} Fabrication DSSC using Pt/MWCNT as catalytic layer on the counter electrode. {yields} Study of catalytic activity by Electrochemical Impedance Spectroscopy. -- Abstract: In this study we have employed multiwall carbon nanotubes (MWCNT), decorated with platinum as catalytic layer for the reduction of tri-iodide ions in dye sensitized solar cell (DSSC). MWCNTs have been prepared by a simple one step pyrolysis method using ferrocene as the catalyst and xylene as the carbon source. Platinum decorated MWCNTs have been prepared by chemical reduction method. The as prepared MWCNTs and Pt/MWCNTs have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In combination with a dye adsorbed TiO{sub 2} photoanode and an organic liquid electrolyte, Pt/MWCNT composite showed an enhanced short circuit current density of 16.12 mA/cm{sup 2} leading to a cell efficiency of 6.50% which is comparable to that of Platinum.

Controlled synthesis of the tricontinuous mesoporous material IBN-9 and its carbon and platinum derivatives

KAUST Repository

Zhao, Yunfeng; Zhang, Daliang; Zhao, Lan; Wang, Guangchao; Zhu, Yihan; Cairns, Amy; Sun, Junliang; Zou, Xiaodong; Han, Yu

2011-01-01

materials (e.g., carbon and platinum) via a "hard- templating" synthesis route. The obtained carbon material possesses large surface area (∼1900 m2/g), high pore volume (1.56 cm 3/g), and remarkable gas adsorption capability at both cryogenic temperatures

Enhanced cis-platinum ototoxicity in children with brain tumours who have received simultaneous or prior cranial irradiation

International Nuclear Information System (INIS)

Walker, D.A.; Pillow, J.; Waters, K.D.; Keir, E.

1989-01-01

We report on four children who received cis-platinum simultaneously with, or in one case 10 months after, cranial irradiation and experienced exaggerated ototoxicity affecting all audible frequencies. The hearing loss was severe, affecting the critical areas for speech perception, and necessitated the provision of bilateral hearing aids. The audiograms of these patients are shown and compared to those of four children who had received cis-platinum as part of their treatment for neuroblastoma but without cranial irradiation. The precipitation of the exaggerated hearing loss with the administration of cis-platinum in one patient 10 months after finishing cranial irradiation suggests that care should be taken in the timing of cis-platinum administration in relation to concurrent or previous cranial irradiation

Global exploration and production capacity for platinum-group metals from 1995 through 2015

Science.gov (United States)

Wilburn, David R.

2012-01-01

Platinum-group metals (PGMs) are required in a variety of commercial, industrial, and military applications for many existing and emerging technologies, yet the United States is highly dependent on foreign sources of PGMs. Information on global exploration for PGMs since 1995 has been used in this study as a basis for identifying locations where the industry has determined that exploration has provided data sufficient to warrant development of a new mine or expansion of an existing operation or where a significant increase in capacity for PGMs is anticipated by 2015. Discussions include an overview of the industry and the selected sites, factors affecting mineral supply, and circumstances leading to the development of mineral properties with the potential to affect mineral supply. Of the 52 sites or regional operations that were considered in this analysis, 16 sites were producing before 1995, 28 sites commenced production from 1995 through 2010, and 8 sites were expected to begin production from 2011 through 2015 if development plans came to fruition. The United States imports PGMs primarily from Canada, Russia, South Africa, and Zimbabwe to meet increasing demand for these materials in a variety of specialized and high-tech applications. Feed sources of PGMs are changing in South Africa and Russia, which together accounted for about 89 percent of platinum production and 82 percent of palladium production in 2009. A greater amount of South African PGM capacity is likely to come from deeper, higher cost Upper Group Reef seam 2 deposits and deposits in the Eastern Bushveld area. Future Russian PGM capacity is likely to come from ore zones with generally lower PGM content and different platinum-to-palladium ratios than the nickel-rich ore that dominated PGM supply in the 1990s. Because PGM supply from Canada and Russia is derived as a byproduct of copper and nickel mining, the PGM supply from these countries is influenced by economic, environmental, political, and

TEM and EELS studies of microwave-irradiation synthesis of bimetallic platinum nanocatalysts

International Nuclear Information System (INIS)

Mathe, N R; Scriba, M R; Coville, N J; Olivier, J E

2014-01-01

Microwave-irradiation (MW) synthesis of nanostructured materials provides for the synthesis of metal nanoparticles, using fast and uniform heating rates. This procedure affords better control of the shape and size of the nanoparticles when compared to conventional methods. In this work, microwave-irradiation was used to produce platinum-cobalt (Pt-Co) and platinum-nickel (Pt-Ni) nanoparticles for use as electrocatalysts in the methanol oxidation reaction. High resolution TEM imaging and EELS studies revealed that these bimetallic nanoparticles form islands or hetero-structures

Thiosemicarbazone complexes of the platinum metals. A story of ...

Indian Academy of Sciences (India)

Unknown

Thiosemicarbazone complexes; platinum metals; variable coordination; ... carbonylic carbon via one or two intervening atoms, D,N,S tricoordination usually takes .... modelling studies show that in this coordination mode, the phenyl ring of the.

Identification of the formation of metal-vinylidene interfacial bonds of alkyne-capped platinum nanoparticles by isotopic labeling.

Science.gov (United States)

Hu, Peiguang; Chen, Limei; Deming, Christopher P; Bonny, Lewis W; Lee, Hsiau-Wei; Chen, Shaowei

2016-10-07

Stable platinum nanoparticles were prepared by the self-assembly of 1-dodecyne and dodec-1-deuteroyne onto bare platinum colloid surfaces. The nanoparticles exhibited consistent core size and optical properties. FTIR and NMR measurements confirmed the formation of Pt-vinylidene (Pt[double bond, length as m-dash]C[double bond, length as m-dash]CH-) interfacial linkages rather than Pt-acetylide (Pt-C[triple bond, length as m-dash]C-) and platinum-hydride (Pt-H) bonds.

The influence of nitrate concentrations and acidity on the electrocatalytic reduction of nitrate on platinum

NARCIS (Netherlands)

Groot, de M.T.; Koper, M.T.M.

2004-01-01

A study was performed to determine the influence of nitrate concentration and acidity on the reaction rate and selectivity of the electrocatalytic nitrate reduction on platinum. There are two different nitrate reduction mechanisms on platinum: a direct mechanism (0.4–0.1 V vs. SHE) and an indirect

Indium Doped Zinc Oxide Thin Films Deposited by Ultrasonic Chemical Spray Technique, Starting from Zinc Acetylacetonate and Indium Chloride

Directory of Open Access Journals (Sweden)

Rajesh Biswal

2014-07-01

Full Text Available The physical characteristics of ultrasonically sprayed indium-doped zinc oxide (ZnO:In thin films, with electrical resistivity as low as 3.42 × 10−3 Ω·cm and high optical transmittance, in the visible range, of 50%–70% is presented. Zinc acetylacetonate and indium chloride were used as the organometallic zinc precursor and the doping source, respectively, achieving ZnO:In thin films with growth rate in the order of 100 nm/min. The effects of both indium concentration and the substrate temperature on the structural, morphological, optical, and electrical characteristics were measured. All the films were polycrystalline, fitting well with hexagonal wurtzite type ZnO. A switching in preferential growth, from (002 to (101 planes for indium doped samples were observed. The surface morphology of the films showed a change from hexagonal slices to triangle shaped grains as the indium concentration increases. Potential applications as transparent conductive electrodes based on the resulting low electrical resistance and high optical transparency of the studied samples are considered.

Combination cediranib and olaparib versus olaparib alone for women with recurrent platinum-sensitive ovarian cancer: a randomised phase 2 study.

Science.gov (United States)

Liu, Joyce F; Barry, William T; Birrer, Michael; Lee, Jung-Min; Buckanovich, Ronald J; Fleming, Gini F; Rimel, Bj; Buss, Mary K; Nattam, Sreenivasa; Hurteau, Jean; Luo, Weixiu; Quy, Philippa; Whalen, Christin; Obermayer, Lisa; Lee, Hang; Winer, Eric P; Kohn, Elise C; Ivy, S Percy; Matulonis, Ursula A

2014-10-01

Olaparib is a poly(ADP-ribose) polymerase inhibitor and cediranib is an anti-angiogenic agent with activity against VEGF receptor (VEGFR) 1, VEGFR2, and VEGFR3. Both oral agents have antitumour activity in women with recurrent ovarian cancer, and their combination was active and had manageable toxicities in a phase 1 trial. We investigated whether this combination could improve progression-free survival (PFS) compared with olaparib monotherapy in women with recurrent platinum-sensitive ovarian cancer. In our randomised, open-label, phase 2 study, we recruited women (aged ≥18 years) who had measurable platinum-sensitive, relapsed, high-grade serous or endometrioid ovarian, fallopian tube, or primary peritoneal cancer, or those with deleterious germline BRCA1/2 mutations from nine participating US academic medical centres. We randomly allocated participants (1:1) according to permuted blocks, stratified by germline BRCA status and previous anti-angiogenic therapy, to receive olaparib capsules 400 mg twice daily or the combination at the recommended phase 2 dose of cediranib 30 mg daily and olaparib capsules 200 mg twice daily. The primary endpoint was progression-free survival analysed in the intention-to-treat population. The phase 2 trial is no longer accruing patients. An interim analysis was conducted in November, 2013, after 50% of expected events had occurred and efficacy results were unmasked. The primary analysis was performed on March 31, 2014, after 47 events (66% of those expected). The trial is registered with ClinicalTrials.gov, number NCT01116648. Between Oct 26, 2011, and June 3, 2013, we randomly allocated 46 women to receive olaparib alone and 44 to receive the combination of olaparib and cediranib. Median PFS was 17·7 months (95% CI 14·7-not reached) for the women treated with cediranib plus olaparib compared with 9·0 months (95% CI 5·7-16·5) for those treated with olaparib monotherapy (hazard ratio 0·42, 95% CI 0·23-0·76; p=0·005). Grade

Study on the occurrence of platinum in Xinjie Cu-Ni sulfide deposits by a combination of SPM and NAA

International Nuclear Information System (INIS)

Li Xiaolin; Zhu Jieqing; Lu Rongrong; Gu Yingmei; Wu Xiankang; Chen Youhong

1997-01-01

A combination of neutron-activation analysis (NAA) and scanning proton microprobe (SPM) was used to study the distribution of platinum-group elements (PGEs) in rocks and ores from Xinjie Cu-Ni deposit. The minimum detection limits of PGEs by NAA had been much improved by means of a nickel-sulfide fire-assay technique for pre-concentration of PGEs in the ore samples. A simple and effective method was developed for true element mapping in SPM experiments. A pair of moveable absorption filters was set up in the target chamber for high sensitivities of both major and trace elements. The bulk analysis results by NNA indicated that the PGE mineralization occurred at the base of Xinjie layered intrusion in clino-pyroxenite rocks and the Cu-Ni sulfide minerals disseminated within the rocks had high abundance level of PGEs. However, the micro-PIXE analysis of the Cu-Ni sulfide mineral grains did not find PGEs above the MDL of (6-9) x 10 -6 for Rh, Ru and Pd, and 6- x 10 -6 for Pt. The search for platinum occurrence in sulfide minerals was followed by scanning analysis of SPM when some smaller platinum enriched grains were found in the sulfide minerals. The microscopic analysis results suggested that platinum occurred in the Cu-Ni sulfide matrix as independent arsenide mineral grains. The chemical formula of the arsenide sperrylite was PtAs2. The information of the platinum occurrence was helpful to future mineralogical research and mineral processing and beneficiation of the Cu-Ni deposit

Study on the occurrence of platinum in Xinjie CuNi sulfide deposits by a combination of SPM and NAA

Science.gov (United States)

Li, Xiaolin; Zhu, Jieqing; Lu, Rongrong; Gu, Yingmei; Wu, Xiankang; Chen, Youhong

1997-07-01

A combination of neutron-activation analysis (NAA) and scanning proton microprobe (SPM) was used to study the distribution of platinum-group elements (PGEs) in rocks and ores from Xinjie CuNi deposit. The minimum detection limits of PGEs by NAA had been much improved by means of a nickel-sulfide fire-assay technique for pre-concentration of PGEs in the ore samples. A simple and effective method was developed for true element mapping in SPM experiments. A pair of moveable absorption filters was set up in the target chamber for high sensitivities of both major and trace elements. The bulk analysis results by NNA indicated that the PGE mineralization occurred at the base of Xinjie layered intrusion in clinopyroxenite rocks and the CuNi sulfide minerals disseminated within the rocks had high abundance level of PGEs. However, the micro-PIXE analysis of the CuNi sulfide mineral grains did not find PGEs above the MDL of 6-9 ppm for Rh, Ru and Pd, and 60 ppm for Pt. The search for platinum occurrence in sulfide minerals was followed by scanning analysis of SPM when some smaller platinum enriched grains were found in the sulfide minerals. The microscopic analysis results suggested that platinum occurred in the CuNi sulfide matrix as independent arsenide mineral grains. The chemical formula of the arsenide sperrylite was PtAs 2. The information of the platinum occurrence was helpful to future mineralogical research and mineral processing and beneficiation of the CuNi deposit.

Trans labilization of am(m)ine ligands from platinum(II) complexes by cancer cell extracts.

Science.gov (United States)

Kasherman, Yonit; Sturup, Stefan; Gibson, Dan

2009-03-01

Cisplatin, cis-[Pt(NH(3))(2)Cl(2)], is an effective anticancer agent in wide clinical use whose efficacy is affected by cellular interactions with sulfur-containing nucleophiles. These interactions can potentially enhance the efficacy of the drug by mediating its delivery to nuclear DNA or inactivate the drug by binding to it irreversibly or by labilizing the NH(3) ligands. Despite the potential importance of trans-labilization reactions in the mechanism of action of the drug, few detailed studies on trans labilization of the ammines have been conducted. We used 2D NMR to show that some trans labilization occurs in proliferating cells and that aqueous extracts of cancer cells labilized 20% of the amine ligands of cis-[PtCl(2)((13)CH(3)NH(2))(2)] after a 12-h incubation. Both low molecular mass nucleophiles (less than 3 kDa) and high molecular mass nucleophiles (more than 3 kDa) labilize the amines with similar efficiency. Studies with model compounds show that thiols and thioethers bind to platinum(II) at similar rates, but thioethers are significantly more efficient at labilizing the am(m)ine at lower pH. N-Acetylcysteine is a more efficient trans-labilizer than glutathione, suggesting that the displacement of the amine proceeds through an associative mechanism. The lag time, the time that elapses from the formation of the Pt-S bond till the release of the amine trans to the sulfur, depends on the pH (for thiols), increasing at lower pH. Quantification of the platinum adducts obtained from incubation of cisplatin with cell extracts indicates that two thirds of the platinum is bound to cellular components with molecular mass greater than 3 kDa.

In vitro circumvention of cisplatin resistance by the novel sterically hindered platinum complex AMD473.

Science.gov (United States)

Holford, J.; Sharp, S. Y.; Murrer, B. A.; Abrams, M.; Kelland, L. R.

1998-01-01

A novel sterically hindered platinum complex, AMD473 [cis-aminedichloro(2-methylpyridine) platinum (II)], has been selected for phase I clinical trials due to commence in 1997. AMD473 was rationally designed to react preferentially with nucleic acids over sulphur ligands such as glutathione. This report documents the in vitro circumvention of acquired cisplatin resistance mechanisms in human ovarian carcinoma (HOC) cell lines by AMD473. In a panel of 11 HOC cell lines, AMD473 showed intermediate growth inhibition potency (mean IC50 of 8.1 microM) in comparison to cisplatin (mean IC50 of 2.6 microM) and carboplatin (mean IC50 of 20.3 microM). AMD473 showed only a 30.7-fold increase in IC50 value from the most sensitive to the most resistant HOC cell line, whereas for cisplatin it was 117.9-fold and for carboplatin 119.7-fold. AMD473 also showed significantly (P or = 14 h for AMD473) after equitoxic doses were exposed to HOC cells for 2 h. AMD473 ICLs in the CH1 HOC cell line were slowly formed and showed no visible signs of being repaired 24 h after removal of drug. This was paralleled by a slower, longer lasting induction of p53 protein by equitoxic doses of AMD473 in HOC cell lines with wild-type p53. This new class of sterically hindered platinum compound, selected for clinical trial in 1997, may therefore elicit improved clinical response in intrinsically and acquired cisplatin-resistant tumours in the clinic. Images Figure 9 PMID:9472630

Tin dioxide sol-gel derived films doped with platinum and antimony deposited on porous silicon

NARCIS (Netherlands)

Savaniu, C.; Arnautu, A.; Cobianu, C.; Craciun, G.; Flueraru, C.; Zaharescu, M.; Parlog, C.; Paszti, F.; van den Berg, Albert

1999-01-01

SnO2 sol-gel derived thin films doped simultaneously with Pt and Sb are obtained and reported for the first time. The Sn sources were tin(IV) ethoxide or tin(II) ethylhexanoate, while hexachloroplatinic acid (H2PtCl6) and antimony chloride (SbCl3) were used as platinum and antimony sources,

Chiral discrimination in platinum anticancer drugs

Czech Academy of Sciences Publication Activity Database

Benedetti, M.; Malina, Jaroslav; Kašpárková, Jana; Brabec, Viktor; Natile, G.

2002-01-01

Roč. 110, Suppl. 5 (2002), s. 779-782 ISSN 0091-6765 R&D Projects: GA ČR GA301/00/0556; GA ČR GA305/02/1552; GA AV ČR IAA7004805; GA AV ČR IBS5004107; GA MŠk OC D20.001 Institutional research plan: CEZ:AV0Z5004920 Keywords : DNA * platinum * cancer Subject RIV: BO - Biophysics Impact factor: 3.452, year: 2002

Platinum Catalysts Supported on Ce, Zr, Pr - Oxides in Catalytic Wet Air Oxidation of Acetic Acid

Czech Academy of Sciences Publication Activity Database

Mikulová, Jana; Rossignol, S.; Barbier Jr., J.; Duprez, D.; Kappenstein, C.

2007-01-01

Roč. 146, č. 3 (2007), s. 1248-1253 ISSN 0304-3894 Institutional research plan: CEZ:AV0Z40720504 Keywords : platinum * cerium oxide * carbonate species Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.337, year: 2007

Platinum nanoparticles: a non-toxic, effective and thermally stable alternative plasmonic material for cancer therapy and bioengineering.

Science.gov (United States)

Samadi, Akbar; Klingberg, Henrik; Jauffred, Liselotte; Kjær, Andreas; Bendix, Poul Martin; Oddershede, Lene B

2018-05-17

Absorption of near infrared (NIR) light by metallic nanoparticles can cause extreme heating and is of interest for instance in cancer treatment since NIR light has a relatively large penetration depth into biological tissue. Here, we quantify the extraordinary thermoplasmonic properties of platinum nanoparticles and demonstrate their efficiency in photothermal cancer therapy. Although platinum nanoparticles are extensively used for catalysis, they are much overlooked in a biological context. Via direct measurements based on a biological matrix we show that individual irradiated platinum nanoparticles with diameters of 50-70 nm can easily reach surface temperatures up to 900 K. In contrast to gold nanoshells, which are often used for photothermal purposes, we demonstrate that the platinum particles remain stable at these extreme temperatures. The experiments are paralleled by finite element modeling confirming the experimental results and establishing a theoretical understanding of the particles' thermoplasmonic properties. At extreme temperatures it is likely that a vapor layer will form around the plasmonic particle, and we show this scenario to be consistent with direct measurements and simulations. Viability studies demonstrate that platinum nanoparticles themselves are non-toxic at therapeutically relevant concentrations, however, upon laser irradiation we show that they efficiently kill human cancer cells. Therefore, platinum nanoparticles are highly promising candidates for thermoplasmonic applications in the life sciences, in nano-medicine, and for bio-medical engineering.

The development of platinum-based alloys and their thermodynamic database

OpenAIRE

Cornish L.A.; Hohls J.; Hill P.J.; Prins S.; Süss R.; Compton D.N.

2002-01-01

A series of quaternary platinum-based alloys have been demonstrated to exhibit the same two-phase structure as Ni-based superalloys and showed good mechanical properties. The properties of ternary alloys were a good indication that the quaternary alloys, with their better microstructure, will be even better. The quaternary alloy composition has been optimised at Pt84:Al11:Ru2:Cr3 for the best microstructure and hardness. Work has begun on establishing a thermodynamic database for Pt-Al-Ru-Cr ...

In vitro permeation of platinum through African and Caucasian skin.

Science.gov (United States)

Franken, A; Eloff, F C; du Plessis, J; Badenhorst, C J; Du Plessis, J L

2015-02-03

The majority of the South African workforce are Africans, therefore potential racial differences should be considered in risk and exposure assessments in the workplace. Literature suggests African skin to be a superior barrier against permeation and irritants. Previous in vitro studies on metals only included skin from Caucasian donors, whereas this study compared the permeation of platinum through African and Caucasian skin. A donor solution of 0.3 mg/ml of potassium tetrachloroplatinate (K₂PtCl₄) dissolved in synthetic sweat was applied to the vertical Franz diffusion cells with full thickness abdominal skin. Skin from three female African and three female Caucasian donors were included (n=21). The receptor solution was removed at various intervals during the 24 h experiment, and analysed with high resolution inductively coupled plasma-mass spectrometry (ICP-MS). Skin was digested and analysed by inductively coupled plasma-optical emission spectrometry (ICP-OES). Significantly higher permeation of platinum through intact African skin (p=0.044), as well as a significantly higher mass of platinum retention in African skin in comparison with Caucasian skin (p=0.002) occurred. Significant inter-donor variation was found in both racial groups (pskin and further investigation is necessary to explain the higher permeation through African skin. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Nanoparticulate platinum films on gold using dendrimer-based wet ...

Indian Academy of Sciences (India)

Central Electrochemical Research Institute, Karaikudi 630 006, India. E-mail: ... deposition methods for applications involving thin films, e.g., catalysis. Deposition of platinum .... The spectrum recorded at 0.3 V shows a mixed control behaviour ...

Spectral studies on the interaction of acetylacetone with aluminum-containing MCM-41 mesoporous materials

International Nuclear Information System (INIS)

Zanjanchi, M.A.; Vaziri, M.

2008-01-01

Diffuse reflectance spectroscopy (DRS) was used to study the interaction of acetylacetone (acac) with the mesoporous aluminum-containing MCM-41 materials. A room temperature synthesis method was used for preparation of purely siliceous MCM-41 and for aluminum-containing MCM-41 materials. Samples with Si/Al ratios of 50, 20, 10 and 5 were synthesized. The synthesized mesoporous materials possess highly ordered structure and high surface area as evidenced from X-ray diffraction and nitrogen physisorption measurements, respectively. The treatment of the as-synthesized aluminum-containing MCM-41 samples with acac shows a distinct band at ∼290 nm. This band is assigned to six coordinated aluminum atoms in the structure which is produced by diffusion of acac molecules through surfactant micelles and their interaction with aluminum atoms. The 290-nm band disappears upon several successive washing of the sample with ethanol. The treatment of the calcined aluminum-containing MCM-41 sample with acac produces the same 290-nm band where its intensity increases with the aluminum content of the sample. The intensity of this band is reduced upon successive ethanol washing, but remains nearly constant after three times washing. This irremovable aluminum species can be assigned to framework aluminum. The measured acidity for our aluminum-containing MCM-41 samples correlates linearly with the intensity of 290-nm band for the ethanol treated samples. This supports the idea that the Bronsted acidity in aluminum-modified MCM-41 samples is a function of the amount of tetrahedral framework aluminum in the structure

Platinum Jubilee of the Indian Academy of Science

Indian Academy of Sciences (India)

user

Platinum Jubilee of the Indian Academy of Science βγ-Crystallins and the bacterial immunoglobulines fold: Two calcium binding folds. Yogendra Sharma. Centre for Cellular and Molecular Biology (CCMB). "Hell is a half-filled auditorium ". Hell is a half-filled auditorium. - Robert Frost (1874-1963) ...

Aqueous synthesis of porous platinum nanotubes at room temperature and their intrinsic peroxidase-like activity.

Science.gov (United States)

Cai, Kai; Lv, Zhicheng; Chen, Kun; Huang, Liang; Wang, Jing; Shao, Feng; Wang, Yanjun; Han, Heyou

2013-07-11

Platinum nanotubes (PtNTs) exhibiting high porosity were constructed by sacrificing the exterior of tellurium nanowires (TeNWs) and disintegrating the inner part spontaneously in aqueous solution at room temperature, in which the Kirkendall effect may play an important role. The present PtNTs exhibited intrinsic peroxidase-like activity in the presence of H2O2.

Tin-Platinum catalysts interactions on titania and silica

International Nuclear Information System (INIS)

Nava, N.; Del Angel, P.; Salmones, J.; Baggio-Saitovitch, E.; Santiago, P.

2007-01-01

Pt-Sn was supported on titania and silica, and the resulting interactions between the components in prepared samples and the resulting interactions between the components before and after treatment with hydrogen were characterized by Moessbauer spectroscopy, X-ray diffraction, Rietveld refinement, high-resolution transmission electron microscopy (HRTEM) and catalytic tests data. Results show the presence of Pt and SnO 2 after calcinations, and Pt 3 Sn, PtSn and PtSn 3 after reduction. Rietveld analysis shows that some Ti 4+ are replaced by Sn 4+ atoms in the titania structure. Finally, HRTEM and the practically absence of activity observed confirms that metallic platinum is encapsulated

Platinum Monolayer Electrocatalysts for Anodic Oxidation of Alcohols.

Science.gov (United States)

Li, Meng; Liu, Ping; Adzic, Radoslav R

2012-12-06

The slow, incomplete oxidation of methanol and ethanol on platinum-based anodes as well as the high price and limited reserves of Pt has hampered the practical application of direct alcohol fuel cells. We describe the electrocatalysts consisting of one Pt monolayer (one atom thick layer) placed on extended or nanoparticle surfaces having the activity and selectivity for the oxidation of alcohol molecules that can be controlled with platinum-support interaction. The suitably expanded Pt monolayer (i.e., Pt/Au(111)) exhibits a factor of 7 activity increase in catalyzing methanol electrooxidation relative to Pt(111). Sizable enhancement is also observed for ethanol electrooxidation. Furthermore, a correlation between substrate-induced lateral strain in a Pt monolayer and its activity/selectivity is established and rationalized by experimental and theoretical studies. The knowledge we gained with single-crystal model catalysts was successfully applied in designing real nanocatalysts. These findings for alcohols are likely to be applicable for the oxidation of other classes of organic molecules.

Selection and development of an easy to process electrolyte for decontamination by electropolishing

International Nuclear Information System (INIS)

Steringer, A.; Moser, T.

1989-01-01

Three different organic electrolytes: formic acid (E 1), oxalic acid (E 2) and acetylacetone (E 3) using potassium bromide (KBr) as the auxiliary electrolyte, were tested in the laboratory for electrochemically dissolving steel and stainless steel. The best results in the preliminary test series were attained with acetylacetone. It ranks among the first for current efficiency, with the produced acetylacetonates having the lowest solubility and thus they settle out of the solution in the form of coarse crystalline products. Tests were made on radioactive reactor components using acetylacetone in a 400 A test facility, to verify and optimize the decontamination factors, the electrolyte service life and the produced waste volume, as well as the respective process parameters. The surface activity of the components ranged from 2 to 10 Bq/cm 2 , and a decontamination factor of 30 was attained. The obtained specific waste volume is 1.1 litre/m 2 of decontaminated surface. A gamma-spectrometric evaluation revealed that the activity in the settled-out metallic acetylacetonate is five times higher than that in the electrolyte. It is only necessary to refill the spent acetylacetonate which makes it then possible to continue to use the electrolyte solution almost unrestrictedly

Electrochemical removal of hexavalent chromium from wastewater using Platinum-Iron/Iron-carbon nanotubes and bipolar Electrodes

Directory of Open Access Journals (Sweden)

Hoshyar Hossini

2015-01-01

Full Text Available Background: In recent decades, electrocoagulation (EC has engrossed much attention as an environmental-friendly and effectiveness process. In addition, the EC process is a potential suitable way for treatment of wastewater with concern to costs and environment. The object of this study was electrochemical evaluation of chromium removal from industrial wastewater using Platinum and carbon nanotubes electrodes. Materials and Methods: The effect of key variables including pH (3–9, hexavalent chromium concentration (50–300 mg/l, supporting electrolyte (NaCl, KCl, Na2CO3 and KNO3 and its dosage, Oxidation-Reduction variations, sludge generation rate and current density (2–20 mA/cm2 was determined. Results: Based on experimental data, optimum conditions were determined in 20, 120 min, pH 3, NaCl 0.5% and 100 mg/L initial concentration of chromium. Conclusions: Removal of hexavalent chromium from the wastewater could be successfully performanced using Platinum-Iron/Iron-carbon nanotubes and bipolar Electrodes.

A novel method for biopolymer surface nanostructuring by platinum deposition and subsequent thermal annealing

Czech Academy of Sciences Publication Activity Database

Slepička, P.; Juřík, P.; Kolská, Z.; Malinský, Petr; Macková, Anna; Michaljaničová, I.; Švorčík, V.

2012-01-01

Roč. 7, č. 671 (2012), s. 1-6 ISSN 1931-7573 R&D Projects: GA ČR(CZ) GBP108/12/G108 Institutional support: RVO:61389005 Keywords : nanopattering * surface morphology * biopolymer * platinum sputtering * thermal annealing Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 2.524, year: 2012

CCT-K2.1: NRC/VNIIFTRI bilateral comparison of capsule-type standard platinum resistance thermometers from 13.8 K to 273.16 K

Energy Technology Data Exchange (ETDEWEB)

Hill, K.D.; Steele, A.G. [National Research Council of Canada, Institute for National Measurement Standards, Ottawa, ON (Canada); Dedikov, Y.A.; Shkraba, V.T. [Institute for Physical-Technical and Radiotechnical Measurements (VNIIFTRI), Moscow (Russian Federation)

2005-04-01

The Consultative Committee for Thermometry Key Comparison 2 (CCT-K2) results were published two years ago (2002 Metrologia 39 551-71). NRC served as the pilot laboratory for CCT-K2 and remains able to provide a scale and measurement system suitable for performing bilateral comparisons linked to the original key comparison results. In March 2003, measurements of two VNIIFTRI 100 {omega} capsule-style platinum resistance thermometers (CSPRTs), S/N 356 and 476, were undertaken to relate their local calibration to the results from the CCT-K2 exercise. The NRC Leeds and Northrup (L and N) CSPRT S/N 1872174 provides the link to the CCT-K2 results. The three CSPRTs were compared at the eight defining cryogenic temperatures of the International Temperature Scale of 1990 (ITS-90) in the range from 13.8033 K to 273.16 K. The reader is referred to the full text of the CCT-K2 report for a detailed explanation of the methodology employed for the comparison. Only the details unique to the measurements reported here will be addressed in this article. The NRC/VNIIFTRI bilateral comparison of capsule-style platinum resistance thermometers over the range 13.8 K to 273.16 K has revealed calibrations at VNIIFTRI to be in agreement with the KCRV of CCT-K2 within the expanded uncertainty for all temperatures of the comparison with the exception of the triple point of hydrogen at 13.8033 K. One of the two CSPRTs supplied by VNIIFTRI was found to be discrepant as revealed by differences at the triple point of water and at the lowest temperatures of the comparison, and was therefore excluded from further analysis. The linkage to the CCT-K2 data supports the evaluation of the VNIIFTRI CMCs in Appendix C of the KCDB. (authors)

Treatment of ammonia by catalytic wet oxidation process over platinum-rhodium bimetallic catalyst in a trickle-bed reactor: effect of pH.

Science.gov (United States)

Hung, Chang-Mao; Lin, Wei-Bang; Ho, Ching-Lin; Shen, Yun-Hwei; Hsia, Shao-Yi

2010-08-01

This work adopted aqueous solutions of ammonia for use in catalytic liquid-phase reduction in a trickle-bed reactor with a platinum-rhodium bimetallic catalyst, prepared by the co-precipitation of chloroplatinic acid (H2PtCl6) and rhodium nitrate [Rh(NO3)3]. The experimental results demonstrated that a minimal amount of ammonia was removed from the solution by wet oxidation in the absence of any catalyst, while approximately 97.0% of the ammonia was removed by wet oxidation over the platinum-rhodium bimetallic catalyst at 230 degrees C with an oxygen partial pressure of 2.0 MPa. The oxidation of ammonia has been studied as a function of pH, and the main reaction products were determined. A synergistic effect is manifest in the platinum-rhodium bimetallic structure, in which the material has the greatest capacity to reduce ammonia. The reaction pathway linked the oxidizing ammonia to nitric oxide, nitrogen, and water.

Synthesis and characterization of platinum supported on alumina doped with cerium catalyst

International Nuclear Information System (INIS)

Yusof Abdullah; Abd Fatah Awang Mat; Mohd Ali Sufi; Sarimah Mahat; Razali Kassim; Nurhaslinda Abdullah.

1996-03-01

The synthesis and characterization of gamma-alumina doped with cerium as platinum support for the automobile exhaust catalyst are described. Platinum/alumina/ceria catalyst were prepared by impregnation of hexachloroplatinic acid and sintered at 500 degree Celsius to obtain metal dispersions of 1.0 wt%. Catalyst distribution inside the powder and the effects of the addition of cerium to alumina were analyzed by the scanning electron microscopy (SEM) and x-ray fluorescence spectroscopy (XRF). The results showed that the alumina - supported catalysts contained well dispersion of the noble metal

Wireless gas sensing in South African underground platinum mines

CSIR Research Space (South Africa)

Abu-Mahfouz, Adnan M

2014-04-01

Full Text Available Approximately 70% of South African mines are classified as fiery, where methane gas potentially could cause explosions. The number of flammable gas reports and accidents are increasing steadily for both gold and platinum mines. However...

Determinants of ototoxicity in 451 platinum-treated Dutch survivors of childhood cancer : A DCOG late-effects study

NARCIS (Netherlands)

Clemens, Eva; de Vries, Andrica C.; Pluijm, Saskia F.; Zehnhoff-Dinnesen, Antoinette Am; Tissing, Wim J.; Loonen, Jacqueline J.; van Dulmen-den Broeder, Eline; Bresters, Dorine; Versluys, Birgitta; Kremer, Leontien C.; van der Pal, Heleen J.; van Grotel, Martine; van den Heuvel-Eibrink, Marry M.

2016-01-01

Platinum-containing chemotherapeutics are efficacious for a variety of pediatric malignancies, nevertheless these drugs can induce ototoxicity. However, ototoxicity data on large cohorts of childhood cancer survivors (CCSs) who received platinum agents, but not cranial irradiation are scarce.

Separation of platinum metals by theirs extraction as sulfides

International Nuclear Information System (INIS)

Pilipenko, A.T.; Ryabushko, O.P.; Ty Van Mak

1978-01-01

Separation of platinum metals by means of their sediment in the form of sulfides with subsequent extraction is studied. The optimum conditions of metal sulfide extraction are determined, the metal output dependence from acidness and aqueous phase composition and also the organic solvent nature are investigated. Ruthenium concentration was determined photometrically. Ruthenium sulfide is extracted by butyl spirit from 1-4 normal hydrochloric acid. The maximum extraction grade of 63% is reached in 3.2-normal acid. When the mixture of acetic and hydrochloric acids (2:1) is used for decomposition of ruthenium tiosalts, the grade of ruthenium extraction by amyl spirit or the mixture of anyl and butyl spirits (1:1) constitutes 100%

PKC-alpha modulation by miR-483-3p in platinum-resistant ovarian carcinoma cells

Energy Technology Data Exchange (ETDEWEB)

Arrighetti, Noemi, E-mail: Noemi.Arrighetti@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Cossa, Giacomo, E-mail: Gia.Cossa@gmail.com [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); De Cecco, Loris, E-mail: Loris.Dececco@istitutotumori.mi.it [Functional Genomics and Bioinformatics, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Stucchi, Simone, E-mail: Simone.Stucchi@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Carenini, Nives, E-mail: Nives.Carenini@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Corna, Elisabetta, E-mail: Elisabetta.Corna@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Gandellini, Paolo, E-mail: Paolo.Gandellini@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Zaffaroni, Nadia, E-mail: Nadia.Zaffaroni@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Perego, Paola, E-mail: paola.perego@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy); Gatti, Laura, E-mail: Laura.Gatti@istitutotumori.mi.it [Molecular Pharmacology Unit, Fondazione IRCCS Istituto Nazionale dei Tumori, via Amadeo 42, Milan 20133 (Italy)

2016-11-01

The occurrence of drug resistance limits the efficacy of platinum compounds in the cure of ovarian carcinoma. Since microRNAs (miRNAs) may contribute to this phenomenon by regulating different aspects of tumor cell response, the aim of this study was to exploit the analysis of expression of miRNAs in platinum sensitive/resistant cells in an attempt to identify potential regulators of drug response. MiR-483-3p, which may participate in apoptosis and cell proliferation regulation, was found up-regulated in 4 platinum resistant variants, particularly in the IGROV-1/Pt1 subline, versus parental cells. Transfection of a synthetic precursor of miR-483-3p in IGROV-1 parental cells elicited a marked up-regulation of the miRNA levels. Growth-inhibition and colony-forming assays indicated that miR-483-3p over-expression reduced cell growth and conferred mild levels of cisplatin resistance in IGROV-1 cells, by interference with their proliferative potential. Predicted targets of miR-483-3p included PRKCA (encoding PKC-alpha), previously reported to be associated to platinum-resistance in ovarian carcinoma. We found that miR-483-3p directly targeted PRKCA in IGROV-1 cells. In keeping with this finding, cisplatin sensitivity of IGROV-1 cells decreased upon molecular/pharmacological inhibition of PKC-alpha. Overall, our results suggest that overexpression of miR-483-3p by ovarian carcinoma platinum-resistant cells may interfere with their proliferation, thus protecting them from DNA damage induced by platinum compounds and ultimately representing a drug-resistance mechanism. The impairment of cell growth may account for low levels of drug resistance that could be relevant in the clinical setting. - Highlights: • miR-483-3p is up-regulated in ovarian carcinoma cells resistant to platinum drugs. • Ectopic expression of miR-483-3p in IGROV-1 confers mild levels of Pt-resistance. • Overexpression of miR-483-3p down-regulates PRKCA levels in ovarian carcinoma cells. • miR 483

WE-FG-BRA-11: Theranostic Platinum Nanoparticle for Radiation Sensitization in Breast Cancer Radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Yue, Y; Wagner, S; Medina-Kauwe, L; Cui, X; Zhang, G; Shiao, S; Sandler, H; Fraass, B [Cedars Sinai Medical Center, Los Angeles, CA (United States)

2016-06-15

Purpose: We have developed a novel receptor-targeted theranostic platinum nanoparticle (HER-PtNP) for enhanced radiation sensitization in HER2-positive breast cancer radiation treatment. This study aims to evaluate receptor-targeting specificity, and radiation sensitization of the nanoparticle. Methods: The platinum nanoparticle (PtNP) was synthesized with the diameter of 2nm, and capped with cysteine. The nanoparticle was tagged with a fluorescent dye (cy5) for the fluoresence detection, and conjuated with HER2/3 targeted protein (HerPBK10) for HER2-targeting specificity. We evaluated the theranostic features using in vitro breast cancer cell models: HER2-positive BT-474, and HER2-negative MDA-MB-231. The HER2-targeting specificity was evaluated using immunofluorescence and confocal microscopy. For each cell line, three sets of samples, including non-stained control, fluorescence stained PtNP-cy5 treated, and HER-PtNP treated, were imaged by confocal microscopy. Two breast cancer cell lineages were incubated with PtNP and HER-PtNP at 10 µg/mL, and then irradiated with X-rays for 2 Gy dose at 50 kVp. A colonogenic assay was used to determine cellular survival fractions by immediately reseeding 300 cells after irradiation in growth media and allowing colonies to grow for 2 weeks. Results: The results of confocal images show that no apparent nanoparticle cellular uptake was observed in the HER2-(MDA-MB-231) cells with 1% for PtNP-cy5 and 0.5% for HER-PtNP. Similarly no apparent PtNP-cy5 uptake (<1%) for BT474 cells was observed. However, there was significant HER-PtNP uptake (73%) for the HER2+(BT474) cells. The clonogenic assay showed that BT474 cells treated with HER-PtNP had significantly lower survival compared to those treated with PtNP (32% vs 81%, p=0.01). However, no significant radiosensitivity enhancement was observed for MDA-MB-231 cell treated with PtNP and HER-PtNP (89% vs 92%, p=0.78). Conclusion: Our studies suggest that the HER2-targeted platinum

WE-FG-BRA-11: Theranostic Platinum Nanoparticle for Radiation Sensitization in Breast Cancer Radiotherapy

International Nuclear Information System (INIS)

Yue, Y; Wagner, S; Medina-Kauwe, L; Cui, X; Zhang, G; Shiao, S; Sandler, H; Fraass, B

2016-01-01

Purpose: We have developed a novel receptor-targeted theranostic platinum nanoparticle (HER-PtNP) for enhanced radiation sensitization in HER2-positive breast cancer radiation treatment. This study aims to evaluate receptor-targeting specificity, and radiation sensitization of the nanoparticle. Methods: The platinum nanoparticle (PtNP) was synthesized with the diameter of 2nm, and capped with cysteine. The nanoparticle was tagged with a fluorescent dye (cy5) for the fluoresence detection, and conjuated with HER2/3 targeted protein (HerPBK10) for HER2-targeting specificity. We evaluated the theranostic features using in vitro breast cancer cell models: HER2-positive BT-474, and HER2-negative MDA-MB-231. The HER2-targeting specificity was evaluated using immunofluorescence and confocal microscopy. For each cell line, three sets of samples, including non-stained control, fluorescence stained PtNP-cy5 treated, and HER-PtNP treated, were imaged by confocal microscopy. Two breast cancer cell lineages were incubated with PtNP and HER-PtNP at 10 µg/mL, and then irradiated with X-rays for 2 Gy dose at 50 kVp. A colonogenic assay was used to determine cellular survival fractions by immediately reseeding 300 cells after irradiation in growth media and allowing colonies to grow for 2 weeks. Results: The results of confocal images show that no apparent nanoparticle cellular uptake was observed in the HER2-(MDA-MB-231) cells with 1% for PtNP-cy5 and 0.5% for HER-PtNP. Similarly no apparent PtNP-cy5 uptake (<1%) for BT474 cells was observed. However, there was significant HER-PtNP uptake (73%) for the HER2+(BT474) cells. The clonogenic assay showed that BT474 cells treated with HER-PtNP had significantly lower survival compared to those treated with PtNP (32% vs 81%, p=0.01). However, no significant radiosensitivity enhancement was observed for MDA-MB-231 cell treated with PtNP and HER-PtNP (89% vs 92%, p=0.78). Conclusion: Our studies suggest that the HER2-targeted platinum

Growth mechanism of graphene on platinum: Surface catalysis and carbon segregation

International Nuclear Information System (INIS)

Sun, Jie; Lindvall, Niclas; Yurgens, August; Nam, Youngwoo; Cole, Matthew T.; Teo, Kenneth B. K.; Woo Park, Yung

2014-01-01

A model of the graphene growth mechanism of chemical vapor deposition on platinum is proposed and verified by experiments. Surface catalysis and carbon segregation occur, respectively, at high and low temperatures in the process, representing the so-called balance and segregation regimes. Catalysis leads to self-limiting formation of large area monolayer graphene, whereas segregation results in multilayers, which evidently “grow from below.” By controlling kinetic factors, dominantly monolayer graphene whose high quality has been confirmed by quantum Hall measurement can be deposited on platinum with hydrogen-rich environment, quench cooling, tiny but continuous methane flow and about 1000 °C growth temperature

The levels of disclosure relating to mine closure obligations by platinum mining companies

Directory of Open Access Journals (Sweden)

Joline Sturdy

2017-06-01

Aim: The aim of this study is to establish the extent to which platinum mines listed on the Johannesburg Stock Exchange (JSE comply with a recommended disclosure framework. Setting: South Africa is the largest producer of platinum in the world. The study covers all platinum mines listed on the JSE. Methods: Using a framework, a census of the annual financial statements, integrated annual reports and sustainability reports or websites was conducted to determine the level of compliance of disclosure relating to mine closure obligations to the recommended disclosure framework. Results: The results show disclosure relating to mine closure obligations of platinum mines listed on the JSE is inconsistent and not sufficient for stakeholders to understand the scope, key assumptions, parameters or reliability of the assessment and calculation of mine closure obligations. Conclusion: The assumptions used to determine mine closure obligations are specialised and multi-disciplinary. The accuracy and reliability of mine closure obligations will improve dramatically through greater transparency and access to information. It is recommended that the JSE listings for mining companies should require a competent person’s report to provide disclosure on assumptions, key values and processes applied to determine the mine closure obligations. Furthermore, it is recommended that the Department of Mineral Resources implements a mechanism of independent assessment of mine closure obligations by experts on an ongoing basis.

New palladium(II) and platinum(II) 5,5-diethylbarbiturate complexes with 2-phenylpyridine, 2,2'-bipyridine and 2,2'-dipyridylamine: synthesis, structures, DNA binding, molecular docking, cellular uptake, antioxidant activity and cytotoxicity.

Science.gov (United States)

Icsel, Ceyda; Yilmaz, Veysel T; Kaya, Yunus; Samli, Hale; Harrison, William T A; Buyukgungor, Orhan

2015-04-21

Novel palladium(ii) and platinum(ii) complexes of 5,5-diethylbarbiturate (barb) with 2-phenylpyridine (Hppy), 2,2'-bipyridine (bpy) and 2,2'-dipyridylamine (dpya) have been prepared and characterized by elemental analysis, IR, UV-Vis, NMR and ESI-MS. Single-crystal diffraction measurements show that complex consists of binuclear [Pd2(μ-barb-κN,O)2(ppy-κN,C)2] moieties, while complexes are mononuclear, [M(barb-κN)2(L-κN,N')] (L = bpy or dpya). has a composition of [Pt(dpya-κN,N')2][Ag(barb-κN)2]2·4H2O and was assumed to have a structure of [Pt(barb-κN)(Hppy-κN)(ppy-κN,C)]·3H2O. The complexes were found to exhibit significant DNA binding affinity by a non-covalent binding mode, in accordance with molecular docking studies. In addition, complexes and displayed strong binding with supercoiled pUC19 plasmid DNA. Cellular uptake studies were performed to assess the subcellular localization of the selected complexes. A moderate radical scavenging activity of and was confirmed by DPPH and ABTS tests. Complexes , , and showed selectivity against HT-29 (colon) cell line.

Real-world hospital costs for nonchemotherapy drugs and nondrug care associated with platinum-based doublets in the first-line setting for advanced nonsquamous non-small-cell lung cancer in Chinese patients: a retrospective cohort study

Directory of Open Access Journals (Sweden)

Chen JH

2016-04-01

Full Text Available Jianhua Chen,1 Shengqi Wu,2 Chenping Hu,3 Yicheng Yang,4 Narayan Rajan,5 Yun Chen,4 Canjuan Yang,6 Jianfeng Li,6 Wendong Chen7 1Department of Medical Oncology, 2Department of Research and Education, Hunan Province Tumor Hospital, 3Department of Respiratory, Xiangya Hospital, Central South University, Changsha, Hunan, 4Lilly Suzhou Pharmaceutical Co., Ltd. Shanghai Branch, Shanghai, People's Republic of China; 5Global Health Outcomes Research, Eli Lilly and Co, Indianapolis, IN, USA; 6Division of Health Outcome Research, Normin Health Changsha Representative Office, Changsha, Hunan, People's Republic of China; 7Normin Health, Toronto, ON, Canada Objective: The objective of this study was to compare hospital costs per treatment cycle (HCTC for nonchemotherapy drugs and nondrug care associated with platinum-based doublets in the first-line setting for advanced nonsquamous non-small-cell lung cancer (AdvNS-NSCLC in Chinese patients. Methods: Patients receiving platinum-based doublets in the first-line setting for AdvNS-NSCLC from 2010 to 2012 in two Chinese tertiary hospitals were identified to create the retrospective study cohort. Propensity score methods were used to create matched treatment groups for head-to-head comparisons on HCTC between pemetrexed–platinum and other platinum-based doublets. Multiple linear regression analyses were performed to rank studied platinum-based doublets for their associations with the log10 scale of HCTC for nonchemotherapy drugs and nondrug care. Results: Propensity score methods created matched treatment groups for pemetrexed–platinum versus docetaxel–platinum (61 pairs, paclitaxel–platinum (39 pairs, gemcitabine–platinum (93 pairs, and vinorelbine–platinum (73 pairs, respectively. Even though the log10 scale of HCTC for nonchemotherapy drugs and nondrug care associated with pemetrexed–platinum was ranked lowest in all patients (coefficient –0.174, P=0.015, which included patients experiencing

Platinum-group elements in the Eastern Deccan volcanic province ...

Indian Academy of Sciences (India)

This study is the first detailed investigation of the platinum-group elements (PGE) at the eastern mar- ... A Zr vs. Pd scattergram found a strong positive correlation for these two elements ..... and the PGE and Au collected by co-precipitation.

The role of support and promoter on the oxidation of sulfur dioxide using platinum based catalysts

DEFF Research Database (Denmark)

Koutsopoulos, Sotiris; Rasmussen, Søren Birk; Eriksen, Kim Michael

2006-01-01

The catalytic oxidation of SO2 to SO3 was studied over platinum based catalysts in the absence and the presence of dopants. The active metal was supported on silica gel or titania (anatase) by impregnation. The activities of the silica supported catalysts were found to follow the order PtRh/SiO2 ...

DNA interaction with platinum-based cytostatics revealed by DNA sequencing.

Science.gov (United States)

Smerkova, Kristyna; Vaculovic, Tomas; Vaculovicova, Marketa; Kynicky, Jindrich; Brtnicky, Martin; Eckschlager, Tomas; Stiborova, Marie; Hubalek, Jaromir; Adam, Vojtech

2017-12-15

The main mechanism of action of platinum-based cytostatic drugs - cisplatin, oxaliplatin and carboplatin - is the formation of DNA cross-links, which restricts the transcription due to the disability of DNA to enter the active site of the polymerase. The polymerase chain reaction (PCR) was employed as a simplified model of the amplification process in the cell nucleus. PCR with fluorescently labelled dideoxynucleotides commonly employed for DNA sequencing was used to monitor the effect of platinum-based cytostatics on DNA in terms of decrease in labeling efficiency dependent on a presence of the DNA-drug cross-link. It was found that significantly different amounts of the drugs - cisplatin (0.21 μg/mL), oxaliplatin (5.23 μg/mL), and carboplatin (71.11 μg/mL) - were required to cause the same quenching effect (50%) on the fluorescent labelling of 50 μg/mL of DNA. Moreover, it was found that even though the amounts of the drugs was applied to the reaction mixture differing by several orders of magnitude, the amount of incorporated platinum, quantified by inductively coupled plasma mass spectrometry, was in all cases at the level of tenths of μg per 5 μg of DNA. Copyright © 2017 Elsevier Inc. All rights reserved.

Nano carbon supported platinum catalyst interaction behavior with perfluorosulfonic acid ionomer and their interface structures

DEFF Research Database (Denmark)