Separation of tributyl phosphate from degraded solvents

International Nuclear Information System (INIS)

Kumar, S.V.; Nadkarni, M.N.; Ramanujam, A.; Venkatesan, M.; Gopalakrishnan, V.; Kazi, J.A.

1977-01-01

A solvent extraction method is described for the recovery of tributyl phosphate (TBP) from degraded process solvents. The method involves the separation of TBP and shell solT(SST) from 30% TBP/SSP mixture by thorium nitrate extraction leading to the formation of a heavy phase (third phase) which contains essentially TBP. The equilibrium experiments revealed that by utilizing thorium feeds of concentrations above 525 g/L in water at 1:1 ratio, a 30% TBP/SST mixture can be effectively separated into TBP and SST fractions with light SST phase having about 3% TBP. Using single stage mixer settler experiments, the feasibility of continuous separation of the three phases was assessed. Since there is a tendency for the degraded products of the diluent to seek the TBP phase, additional treatment steps would be necessary for their removal if the TBP is to be reused. Activated charcoal was investigated for this purpose. If purification of the TBP is not envisaged the volume of the organic waste generated in processing plants could be reduced by separating the diluent and TBP and only the TBP could be sent as concentrated waste. (author)

Cleanup of 7.5% tributyl phosphate/n-paraffin solvent-extraction solvent

International Nuclear Information System (INIS)

Reif, D.J.

1987-02-01

The HM process at the Savannah River Plant uses 7.5% tributyl phosphate in n-paraffin as an extraction solvent. During use, the solvent is altered due to hydrolysis and radiolysis, forming materials which influence product losses, product decontamination, and separation efficiencies. Laboratory studies to improve online solvent cleaning have shown that carbonate washing, although removing residual solvent activity, does not remove binding ligands which hold fission products in the solvent. Treatment of solvent by an alumina adsorption process removes binding ligands and significantly improves recycle solvent performance. Both laboratory work defining a full-scale alumina adsorption process and the use of the process to clean HM process first cycle solvent is discussed

Polarographic behaviour of uranium (VI) in tributyl phosphate organic solutions

International Nuclear Information System (INIS)

Degueldre, C.A.; Meklati, M.

1984-01-01

U(VI) determination by D.C. and differential pulse polarography was studied in the organic solutions derived from tributyl phosphate - diluent extracts (after separation from nitric acid media) along with a selected aprotic solvent (i.e.: propylene carbonate and N,N-dimethylacetamide). Miscibility of the TBP-diluent (e.g. cyclohexane, n-hexane, kerosene, n-dodecane) phase with nitric acid as supporting electrolyte, either by addition or already present in the extract was larger in DMA than in PC. In the DMA organic mixture, U(VI) exhibited a DPP peak due to a one electron step, with Esub(p)=-0.4 V (position connected with H 2 O and HNO 3 concentrations). This peak which was proportionnel to the U(VI) concentration from 5x10 -6 to 10 -3 M can be used to determinate directly hexavalent uranium in the industrial organic extraction phases TBP-diluent. (orig.)

The production of rare earth elements group via tributyl phosphate extraction and precipitation stripping using oxalic acid

OpenAIRE

Jorjani, Esmaeil; Shahbazi, Malek

2016-01-01

In this study, solvent extraction and precipitation stripping were used to produce rare earth elements (REEs). Tributyl phosphate (TBP) was used to extract yttrium, lanthanum, cerium, and neodymium from an aqueous solution produced by nitric acid leaching of apatite concentrate. In the extraction stage, the effects of TBP concentration, pH, contact time, temperature, and phase ratio were investigated. The results show that about 95%, 90%, 87% and 80% of neodymium, cerium, lanthanum, and yttri...

Behavior of tributyl phosphate in A-line processes

International Nuclear Information System (INIS)

Harmon, H.D.; Hyder, M.L.; Tiffany, B.; Gray, L.W.; Soltys, P.A.

1976-08-01

The chemical and physical properties of uranyl nitrate--tributyl phosphate adduct (UO 2 ) (NO 3 ) 2 (TBP) 2 were studied to define optimum, safe operating conditions for denitration of uranyl nitrate (UN) solutions containing low concentrations of adduct. The distribution of TBP between aqueous UN solutions and organic phases (TBP pure or diluted in n-paraffin) was measured. Specific gravity measurements confirmed published data for aqueous UN solutions, but disagreed with literature data for 100 percent TBP. Intersection of the UN specific gravity curve and the 100 percent TBP data of this work indicated that phase inversion cannot occur when the aqueous phase contains greater than or equal to 330 g U/1. Thermal decomposition of adduct occurs in one gradual weight loss step below 170 0 C and in two successive steps above 170 0 C. Rate constants for the first reaction were calculated for 130 to 210 0 C. The major flammable decomposition product was l-butene; inorganic gases formed were N 2 , NO, N 2 O, CO, and CO 2 . Adduct decomposition during denitration of UN was characterized by foaming and by gas evolution (mostly nonflammable) at 135 to 185 0 C. Maximum flammable gas evolution and potential self-heating by TBP oxidation were calculated

Effect of alkaline earth metal and magnesium cations on cadmium extraction from chloride solutions by tributyl phosphate

International Nuclear Information System (INIS)

Prokuev, V.A.; Belousov, E.A.

1985-01-01

At 298 K thermodynamic constants of cadmium (2) extraction from chloride solutions of magnesium, calcium, strontium and barium by tributyl phosphate are calculated. It is established, that logarithm of the thermodynamic extraction constant is in a linear dependence from the change in the cation hydration enthalpy in agqueous solution. It is shown, that activity coefficient of neutral complex CdVCl 2 differs from one, and it is the higher the more stable the complex is in alkaline earth metal chloride solutions

Separation of lanthanum (3) and neodymium (3) by tributyl phosphate extraction in the presence of solid phase

International Nuclear Information System (INIS)

Korotkevich, I.B.; Kolesnikov, A.A.; Bomshtejn, V.E.; Shikhaleeva, N.N.

1987-01-01

Lanthanum (3) and neodymium (3) extraction from nitric acid solutions by tributyl phosphate in the presence of solid phase of the element nitrates is investigated. An increase in distribution of neodymium nitrate in the presence of solid phase with the decrease in its concentration in the initial solution and with the increase in lanthanum nitrate concentration is detected. The highest effect of extractive-crystallizational separation is observed in the range of neodymium nitrate microconcentrations. A method of neodymium quantitative extraction from lanthanum nitrate solutions with neodymium - lanthanum separation coefficient exceeding 25 is suggested

Biodegradation of tributyl phosphate, an organosphate triester, by aerobic granular biofilms

Energy Technology Data Exchange (ETDEWEB)

Nancharaiah, Y.V., E-mail: venkatany@gmail.com; Kiran Kumar Reddy, G.; Krishna Mohan, T.V.; Venugopalan, V.P.

2015-02-11

Graphical abstract: - Highlights: • Aerobic granular biomass was cultivated by feeding TBP along with acetate. • Rapid biodegradation of TBP when used as a co-substrate or as the sole carbon source. • Biodegradation of 2 mM TBP in 5 h with degradation rate of 0.4 μmol mL{sup −1} h{sup −1}. • High phosphatase activity was observed in TBP-degrading granular biomass. • n-Butanol, hydrolyzed product of TBP, was rapidly metabolized by aerobic granules. - Abstract: Tributyl phosphate (TBP) is commercially used in large volumes for reprocessing of spent nuclear fuel. TBP is a very stable compound and persistent in natural environments and it is not removed in conventional wastewater treatment plants. In this study, cultivation of aerobic granular biofilms in a sequencing batch reactor was investigated for efficient biodegradation of TBP. Enrichment of TBP-degrading strains resulted in efficient degradation of TBP as sole carbon or along with acetate. Complete biodegradation of 2 mM of TBP was achieved within 5 h with a degradation rate of 0.4 μmol mL{sup −1} h{sup −1}. TBP biodegradation was accompanied by release of inorganic phosphate in stoichiometric amounts. n-Butanol, hydrolysed product of TBP was rapidly biodegraded. But, dibutyl phosphate, a putative intermediate of TBP degradation was only partially degraded pointing to an alternative degradation pathway. Phosphatase activity was 22- and 7.5-fold higher in TBP-degrading biofilms as compared to bioflocs and acetate-fed aerobic granules. Community analysis by terminal restriction length polymorphism revealed presence of 30 different bacterial strains. Seven bacterial stains, including Sphingobium sp. a known TBP degrader were isolated. The results show that aerobic granular biofilms are promising for treatment of TBP-bearing wastes or ex situ bioremediation of TBP-contaminated sites.

Biodegradation of tributyl phosphate, an organosphate triester, by aerobic granular biofilms

International Nuclear Information System (INIS)

Nancharaiah, Y.V.; Kiran Kumar Reddy, G.; Krishna Mohan, T.V.; Venugopalan, V.P.

2015-01-01

Graphical abstract: - Highlights: • Aerobic granular biomass was cultivated by feeding TBP along with acetate. • Rapid biodegradation of TBP when used as a co-substrate or as the sole carbon source. • Biodegradation of 2 mM TBP in 5 h with degradation rate of 0.4 μmol mL −1 h −1 . • High phosphatase activity was observed in TBP-degrading granular biomass. • n-Butanol, hydrolyzed product of TBP, was rapidly metabolized by aerobic granules. - Abstract: Tributyl phosphate (TBP) is commercially used in large volumes for reprocessing of spent nuclear fuel. TBP is a very stable compound and persistent in natural environments and it is not removed in conventional wastewater treatment plants. In this study, cultivation of aerobic granular biofilms in a sequencing batch reactor was investigated for efficient biodegradation of TBP. Enrichment of TBP-degrading strains resulted in efficient degradation of TBP as sole carbon or along with acetate. Complete biodegradation of 2 mM of TBP was achieved within 5 h with a degradation rate of 0.4 μmol mL −1 h −1 . TBP biodegradation was accompanied by release of inorganic phosphate in stoichiometric amounts. n-Butanol, hydrolysed product of TBP was rapidly biodegraded. But, dibutyl phosphate, a putative intermediate of TBP degradation was only partially degraded pointing to an alternative degradation pathway. Phosphatase activity was 22- and 7.5-fold higher in TBP-degrading biofilms as compared to bioflocs and acetate-fed aerobic granules. Community analysis by terminal restriction length polymorphism revealed presence of 30 different bacterial strains. Seven bacterial stains, including Sphingobium sp. a known TBP degrader were isolated. The results show that aerobic granular biofilms are promising for treatment of TBP-bearing wastes or ex situ bioremediation of TBP-contaminated sites

Internally plasticised cellulose polymers

International Nuclear Information System (INIS)

Burnup, M.; Hayes, G.F.; Fydelor, P.J.

1981-01-01

Plasticised cellulose polymers comprise base polymer having a chain of β-anhydroglucose units joined by ether linkages, with at least one of said units carrying at least one chemically unreactive side chain derived from an allylic monomer or a vinyl substituted derivative of ferrocene. The side chains are normally formed by radiation grafting. These internally plasticised celluloses are useful in particular as inhibitor coatings for rocket motor propellants and in general wherever cellulose polymers are employed. (author)

Extraction And Separation Of GALLIUM With Tributyl Phosphate From The Chloride Leach Liquor Of GATTAR Granite, Eastern Desert, Egypt

International Nuclear Information System (INIS)

MAHDY, M.A.; MAHMOUD, K.F.; ABD EL-HAMEED, A.M.; ZAHRAN, M.A.

2009-01-01

The studied optimum conditions for gallium extraction have confirmed that more than 98.5% of the gallium present in HCl leach liquor of Gattar granite was extracted using 10 % tributyl phosphate (TBP) solvent concentration (v/v) in kerosene as diluent, 15 min shaking time and 1 : 3 organic/ aqueous ratio. About 96 % of the extracted gallium has been stripped from the organic solvent using 0.04 M HCl as aqueous stripping solution. The obtained data clarify that the optimum stripping conditions include 4 min shaking time and 2 : 1 organic/ aqueous ratio.

Biodegradation of tributyl phosphate by granular biofilms

International Nuclear Information System (INIS)

Joshi, Hiren M.; Nancharaiah, Y.V.; Venugopalan, V.P.

2009-01-01

Full text: Tributyl phosphate (TBP) is used as plasticizer for cellulose esters, lacquers, plastic and vinyl resins and as a solvent extractant of rare earth metals. In nuclear power industry, it is used as a solvent for the extraction of uranium and plutonium salts during fuel reprocessing. TBP does not occur naturally in the environment. It is sparingly soluble in water and once released into soil or aquatic systems, is only moderately biodegradable. There are many proposed mechanisms for TBP biodegradation, which involve stepwise enzymatic hydrolysis to orthophosphate and n-butanol and mono-oxygenase based transformation and then degradation. Microbial processes involving multispecies consortia offer better choice over monoculture processes for degradation of complex wastes. Processes based on immobilized microbial consortia are characterized by significantly reduced settling time, high stability in presence of varying organic load, effective mineralization and amenability to bioaugmentation, which make them a good choice for bioremediation and waste water treatment. The objective of this study was to investigate the suitability of aerobic microbial granules (also known as granular biofilms) for efficient biodegradation of TBP. For this purpose, we set up 4 litre cylindrical sequencing batch reactors (SBR) in triplicates and inoculated them with sludge (mean sludge size ∼ 60 mm) obtained from an operating wastewater treatment plant. The SBRs were operated on a 6h cycle with 66% volumetric exchange ratio. The reactors were fed with synthetic waste water along with 90 mM acetate and 0.5 mM TBP. The concentration of TBP was slowly raised to 2mM. After 3 months of operation, microbial granules (mean size: 2.05 mm) capable of TBP degradation were observed in the reactors. Gas chromatographic analysis of samples showed that after 6h of operational cycle 2 mM initial concentration of TBP was reduced to 0.2 mM, after which there was no further degradation. Cessation

Impact of a short-term exposure to tributyl phosphate on morphology, physiology and migratory behaviour of European eels during the transition from freshwater to the marine environment

DEFF Research Database (Denmark)

Privitera, Lucia; Aarestrup, Kim; Moore, Andy

2013-01-01

Migrating silver European eels were exposed for 5 days in a laboratory to an environmental level of tributyl phosphate (TBP), tagged with acoustic transmitters and released below the Tange hydropower station, on the River Gudenaa, Denmark. The subsequent movements of the eels were monitored as th...

Phosphonates as alternative to tributyl phosphate for the separation of actinides from fission products

International Nuclear Information System (INIS)

Vyas, Chirag K.; Joshirao, Pranav M.; Manchanda, Vijay K.; Rao, C.V.S. Brahmmananda; Jayalakshmi, S.

2015-01-01

The present work investigates the role of increase in the basicity of organophosphorus extractant (dialkylalkyl phosphonates) on the uptake of actinides and fission products vis-a-vis tributyl phosphate (TBP), currently employed as a universal extractant. Two dialkylalkyl phosphonates viz. dibutylpropyl phosphonate (DBPrP) and dibutylpentyl phosphonate (DBPeP) were synthesized, characterized and evaluated for their solvent extraction behavior towards U(VI), Th(IV), Eu(III) and Tc(VII) in nitric acid medium ranging from 0.01-6 M. It was observed that increasing the basicity of the phosphoryl oxygen enhanced the uptake of the actinides and the distribution coefficient values were significantly larger as compared to TBP. The limiting organic concentration (LOC) value was estimated for Th(IV) for these extractants and compared with the TBP system. The separation factors of actinides with phosphonates over Tc(VII) are distinctly better than that with TBP.

Determination of 21 trace impurities in UO2 with tributyl phosphate chromatographic separation-USN-inductively coupled/atomic emission spectrometric

International Nuclear Information System (INIS)

Hou Lieqi; Wang Shuan; Li Jie

1996-03-01

A method of tributyl phosphate chromatographic separation-USN-inductively coupled/atomic emission spectrometric was selected. And the parameters, interference of acid concentrations, interference of coexisting elements, selecting of flow for carrier gas, solution temperature were studied. When the sampling amount is 250 mg, the determination range for Al, Ag, Ba, Ca, Cd, Co, Cr, Cu, Fe, In, Li, Mg, Mn, Mo, Ni, Pb, Sn, Ti, V, Y and Zn are 0.2∼100 ng· -1 , recovery are 94%∼110%. The RSD (n 8) are 0.8%∼6.2%. (3 refs., 4 tabs.)

Study of the physico-chemical agents influencing uranium and plutonium extraction by tributylphosphate in nitric media; Etude des facteurs physico-chimiques intervenant dans l'extraction de l'uranium et du plutonium par le phosphate de tributyle en milieu nitrique

Energy Technology Data Exchange (ETDEWEB)

Tarnero, M [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-03-01

The following different factors are reviewed: tributylphosphate concentration, nitric acid concentration, influence of non-extractable nitrates, simultaneous presence of uranium and plutonium, presence of some different ions, temperature, nature of the diluent, addition of a second active solvent (synergic or antagonistic effect), tributylphosphate and diluent degradation. (author) [French] On passe en revue les differents facteurs suivants: concentration en phosphate de tributyle, concentration en acide nitrique, influence des nitrates non-extractibles, presence simultanee d'uranium et de plutonium, presence d'ions divers, addition d'un second solvant actif (effet de synergie, ou effet antagoniste), degradation du phosphate de tributyle et des solvants inertes. (auteur)

Methods of Uranium Determination in solutions of Tributyl Phosphate and Kerosene; Metodos de determinacion de uranio en soluciones de fosfato de tributilo y queroseno

Energy Technology Data Exchange (ETDEWEB)

Petrement Eguiluz, J; Palomares Delgado, F

1962-07-01

A new analytical method for the determination of uranium in organic solutions of tributyl phosphate and kerosene is proposed. In this method the uranium is reectracted from the aqueous phase by reduction with cadmium in acid solution. The uranium can be determined in this solution by the usual methods. In case of very diluted solutions, a direct spectrophtometrical determination of uranium in the organic phase with dibenzoylmethane is proposed. (Author) 21 refs.

Migration of plasticisers from PVC and other polymers

DEFF Research Database (Denmark)

Lundsgaard, Rasmus

). In this work it is shown how diffusion coefficients can be obtained by regression of experimental migration data plotted as the square root of time. This was done from plasticiser migration data of GRINDSTEDr SOFT-N-SAFE, GRINDSTEDr ACETEM 95 CO (Acetem) and Epoxidised Soybean Oil (ESBO) migrating from......The main purpose of this thesis is to investigate, from a modeling point of view, the migration of GRINDSTEDr SOFT-N-SAFE (SNS) and other plasticisers from polyvinyl chloride (PVC) and polyolefin food package materials and into foodstuff (specifically the four food simulants set by EU legislation...... coefficients at 20◦C, except at higher temperatures. Using the finite element mesh method in Matlab and COMSOL environments the migration was modeled with a diffusion coefficient able to change with local plasticiser concentration. Three different models for this plasticiser concentration dependence...

Uranium Rirang ore processing: extraction of uranium from Rirang ore digestion solution with tributyl phosphate

International Nuclear Information System (INIS)

Arief, E. R.; Zahardi; Susilaningtyas

1998-01-01

Uranium is extracted from Rirang ore acid digestion solution containing rare earths. A mixture of tributyl phosphate solvent and kerosene diluent is employed. Several parameters of solvent extraction have been studied included aqueous to organic phase ratio, H 2 O 2 reductor concentration and Tbp concentration in the solvent mixture, as well as the aqueous to organic phase ratio in the stripping process. The optimum conditions for the extraction step include the use of 25% H 2 O 2 (v/v), one to one aqueous to organic ratio, and 40% Tbp in kerosene. The extraction recovery for U, RE, Th, and PO 4 3 - are 99%, 4%, 70%, and 30%, respectively. The stripping step optimum conditions include the use of one to five organic to aqueous phase ratio 0.24 N HNO 3 . and the stripping recovery for U, RE, Th, and PO 4 3 - are 84%, 80%, 72%, and 83%, respectively

Effect of plasticiser on properties of styrene-butadiene-styrene thermoplastic elastomers

International Nuclear Information System (INIS)

Norzalia, S.; Farid, A.S.; O'Brien, M.G.

1999-01-01

This study investigates the properties of plasticised styrene-butadiene-styrene thermoplastic elastomers for possible applications in pharmaceutical, medical and food industries. Unplasticised styrene-butadiene-styrene (USBS) materials: vector 8550-D and vector 4461-D, which are developmental materials introduced by Exxon, and blends of vector 8550-D with vector 4461-D were plasticised paraffinic type plasticisers plastol 172 and plastol 352. Shore A hardness, tensile stress at break, modulus at 100% strain, elongation at break and density values showed a decrease whereas flow properties such as melt flow index (MFI) increased considerably with increasing plasticiser concentration. The properties of the plasticised styrene-butadiene-styrene thermoplastic elastomers were compared to the USBS materials. (author)

Gel electrolytes with ionic liquid plasticiser for electrochromic devices

International Nuclear Information System (INIS)

Desai, S.; Shepherd, R.L.; Innis, P.C.; Murphy, P.; Hall, C.; Fabretto, R.; Wallace, G.G.

2011-01-01

The comparative performance of conducting polymer electrochromic devices (ECDs) utilising gel polymer electrolytes (GPEs) plasticised with ethylene carbonate/propylene carbonate or (N-butyl-3-methylpyridinium trifluoromethanesulphonylimide (P 14 TFSI) has been made. Lithium perchlorate and lithium trifluoromethanesulphonylimide salts were used in the GPEs to provide enhanced ionic conductivity and inhibit phase separation of the polyethyleneoxide (PEO) and plasticiser. ECDs were assembled from cathodically colouring, polyethylenedioxythiophene (PEDOT), and anodically colouring, polypyrrole (PPy), conducting polymer electrochromes deposited by vapour deposition. The photopic contrast switching over the visible light spectrum, switching speeds and device stability of the ECDs were obtained. These studies demonstrate that the ionic liquid (IL) plasticised GPEs are a suitable replacement for pure IL based devices and volatile organic solvent plasticisers based upon ethylene carbonate/propylene carbonate mixtures.

Gel electrolytes with ionic liquid plasticiser for electrochromic devices

Energy Technology Data Exchange (ETDEWEB)

Desai, S.; Shepherd, R.L.; Innis, P.C. [ARC Centre of Excellence for Electromaterials Science, Intelligent Polymer Research Institute, University of Wollongong, Northfields Avenue, Wollongong, NSW 2522 (Australia); Murphy, P. [Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Mawson Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Hall, C.; Fabretto, R. [Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Wallace, G.G., E-mail: gwallace@uow.edu.a [ARC Centre of Excellence for Electromaterials Science, Intelligent Polymer Research Institute, University of Wollongong, Northfields Avenue, Wollongong, NSW 2522 (Australia)

2011-04-15

The comparative performance of conducting polymer electrochromic devices (ECDs) utilising gel polymer electrolytes (GPEs) plasticised with ethylene carbonate/propylene carbonate or (N-butyl-3-methylpyridinium trifluoromethanesulphonylimide (P{sub 14}TFSI) has been made. Lithium perchlorate and lithium trifluoromethanesulphonylimide salts were used in the GPEs to provide enhanced ionic conductivity and inhibit phase separation of the polyethyleneoxide (PEO) and plasticiser. ECDs were assembled from cathodically colouring, polyethylenedioxythiophene (PEDOT), and anodically colouring, polypyrrole (PPy), conducting polymer electrochromes deposited by vapour deposition. The photopic contrast switching over the visible light spectrum, switching speeds and device stability of the ECDs were obtained. These studies demonstrate that the ionic liquid (IL) plasticised GPEs are a suitable replacement for pure IL based devices and volatile organic solvent plasticisers based upon ethylene carbonate/propylene carbonate mixtures.

Tritium distribution ratios between the 30 % tributyl phosphate(TBP)-normal dodecane(nDD) organic phase and uranyl nitrate-nitric acid aqueous phase

International Nuclear Information System (INIS)

Fujine, Sachio; Uchiyama, Gunzou; Sugikawa, Susumu; Maeda, Mitsuru; Tsujino, Takeshi.

1989-10-01

Tritium distribution ratios between the organic and aqueous phases were measured for the system of 30 % tributyl phosphate(TBP)-normal dodecane(nDD)/uranyl nitrate-nitric acid water. It was confirmed that tritium is extracted by TBP into the organic phase in both chemical forms of tritiated water (HTO) and tritiated nitric acid (TNO 3 ). The value of tritium distribution ratio ranged from 0.002 to 0.005 for the conditions of 0-6 mol/L nitric acid, 0.5-800 mCi/L tritium in aqueous phase, and 0-125 g-U/L uranium in organic phase. Isotopic distribution coefficient of tritium between the organic and aqueous phases was observed to be about 0.95. (author)

Contribution to the study of uranyl salts in butyl phosphate solutions

International Nuclear Information System (INIS)

Coulon, A.

1965-06-01

A spectroscopic study in the normal infrared region and involving the following associations: tri-alkyl phosphates (tri-butyl, tri-ethyl, tri-methyl), uranyl salts (nitrate, chloride, acetate) has confirmed the existence of an interaction between the phosphoryl group and the uranium atom, as shown by a movement of absorption band for the valency P = 0 from ∼ 1270 cm -1 to ∼ 1180 cm -1 . A study of the preparation, analysis and spectroscopy of the solids obtained by the precipitation of uranyl salts by acid butyl phosphates has been carried out. By infrared spectrophotometry it has been shown that the tri-butyl and di-butyl phosphates are associated in non-polar diluents even before the uranium is introduced. The extraction of uranyl salts from acid aqueous solutions by a diluted mixture of tri-butyl and di-butyl phosphates proceeds by different mechanisms according to the nature of the ion (nitrate or chloride). (author) [fr

Characterization, Leaching, and Filtration Testing for Tributyl Phosphate (TBP, Group 7) Actual Waste Sample Composites

Energy Technology Data Exchange (ETDEWEB)

Edwards, Matthew K.; Billing, Justin M.; Blanchard, David L.; Buck, Edgar C.; Casella, Amanda J.; Casella, Andrew M.; Crum, J. V.; Daniel, Richard C.; Draper, Kathryn E.; Fiskum, Sandra K.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Snow, Lanee A.; Swoboda, Robert G.

2009-03-09

.A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. The actual waste-testing program included homogenizing the samples by group, characterizing the solids and aqueous phases, and performing parametric leaching tests. The tributyl phosphate sludge (TBP, Group 7) is the subject of this report. The Group 7 waste was anticipated to be high in phosphorus as well as aluminum in the form of gibbsite. Both are believed to exist in sufficient quantities in the Group 7 waste to address leaching behavior. Thus, the focus of the Group 7 testing was on the removal of both P and Al. The waste-type definition, archived sample conditions, homogenization activities, characterization (physical, chemical, radioisotope, and crystal habit), and caustic leaching behavior as functions of time, temperature, and hydroxide concentration are discussed in this report. Testing was conducted according to TP-RPP-WTP-467.

Comparison of 2-Octanol and Tributyl Phosphate in Recovery of Tungsten from Sulfuric-Phosphoric Acid Leach Solution of Scheelite

Science.gov (United States)

Liao, Yulong; Zhao, Zhongwei

2018-04-01

Tungsten was recovered from sulfuric-phosphoric acid leach solution of scheelite using 2-octanol and tributyl phosphate (TBP). Approximately 76% of the tungsten and less than 6.2% of the iron were extracted when using 70% 2-octanol, showing good selectivity for tungsten over iron; the tungsten extraction could not be significantly enhanced using a three-stage countercurrent simulation test. Moreover, more than 99.2% of the W and 91.0% of the Fe were extracted when using 70% TBP, showing poor selectivity, but after pretreating the leach solution with iron powder, less than 5.5% of the Fe was extracted. The loaded phases were stripped using deionized water and ammonia solution. The maximum stripping rate of tungsten from loaded 2-octanol was 45.6% when using water, compared with only 13.1% from loaded TBP. Tungsten was efficiently stripped from loaded phases using ammonia solution without formation of Fe(OH)3 precipitate. Finally, a flow sheet for recovery of tungsten with TBP is proposed.

Removal of organic wastes containing tributyl phosphate

International Nuclear Information System (INIS)

Drobnik, S.

TBP in dodecane and kerosene is one of the waste solutions from the reprocessing of spent nuclear fuels by the Purex process. The following methods were investigated for removing the organic solvents: adsorption on suitable solids, extraction, reaction with neutral salts, and saponification with acids or alkalis. Results showed that the best method of TBP removal is saponification with alkali hydroxides, either with dibutyl phosphate or with ortho-phosphate

The production of rare earth elements group via tributyl phosphate extraction and precipitation stripping using oxalic acid

Directory of Open Access Journals (Sweden)

Esmaeil Jorjani

2016-11-01

Full Text Available In this study, solvent extraction and precipitation stripping were used to produce rare earth elements (REEs. Tributyl phosphate (TBP was used to extract yttrium, lanthanum, cerium, and neodymium from an aqueous solution produced by nitric acid leaching of apatite concentrate. In the extraction stage, the effects of TBP concentration, pH, contact time, temperature, and phase ratio were investigated. The results show that about 95%, 90%, 87% and 80% of neodymium, cerium, lanthanum, and yttrium, respectively, can be extracted in optimum conditions of extraction. Hot, deionized water was used to scrub the impurities from the loaded organic phase. The results showed that three stages of scrubbing with a phase ratio (Va/Vo of five removed about 80%, 30%, 27%, and 15% of Ca, Mg, Fe, and P, respectively, from loaded TBP, while less than 9% of total REEs was lost. The effects on precipitation stripping of oxalic acid concentration, contact time, and phase ratio were investigated. The results showed that precipitation stripping is a viable alternative to traditional acid stripping in the REEs production process. Mixed REEs oxide with an assay of about 90% can be achieved as a final product.

Criticality parameters for uranyl nitrate or plutonium nitrate systems in tributyl phosphate/kerosine and water

International Nuclear Information System (INIS)

Weber, W.

1985-01-01

This report presents the calculated values of smallest critical masses and volumina and neutron physical parameters for uranyl nitrate (3, 4, 5% U-235) or plutonium nitrate (5% Pu-240), each in a 30 per cent solution of tributyl phosphate (TBP)/kerosine. For the corresponding nitrate-water solutions, newly calculated results are presented together with a revised solution density model. A comparison of the data shows to what extent the criticality of nitrate-TBP/kerosine systems can be assessed on the basis of nitrate-water parameters, revealing that such data can be applied to uranyl nitrate/water systems, taking into account that the smallest critical mass of uranyl nitrate-TBP/kerosine systems, up to a 5 p.c. U-235 enrichment, is by 4.5 p.c. at the most smaller than that of UNH-water solutions. Plutonium nitrate (5% Pu-240) in the TBP/kerosine solution will have a smallest critical mass of up to 7 p.c. smaller, as compared with the water data. The suitability of the computing methods and cross-sections used is verified by recalculating experiments carried out to determine the lowest critical enrichment of uranyl nitrate. The calculated results are well in agreement with experimental data. The lowest critical enrichment is calculated to be 2.10 p.c. in the isotope U-235. (orig.) [de

Tributyl phosphate removal from reprocessing off-gas streams using a selected sorbent

International Nuclear Information System (INIS)

Parker, G.B.

1980-01-01

Laboratory experiments used small laboratory-scale columns packed with selected sorbent materials to remove tributyl phosphate (TBP) and iodine at conditions approaching those in actual reprocessing off-gas streams. The sorbent materials for TBP removal were placed upstream of iodine sorbent materials to protect the iodine sorbent from the deleterious effects of TBP. Methyl iodide in an airstream containing 30% TBP in normal paraffin hydrocarbons (NPH) and water vapor was metered to two packed columns of sorbents simultaneously (in parallel). One column contained a segment of 8-in. x 14-in. mesh alumina sorbent for TBP removal, the other did not. The measure of the effectiveness of TBP sorbent materials for TBP removal was determined by comparing the iodine retention of the iodine sorbent materials in the two parallel columns. Results from an 18 wt % Ag substituted mordenite iodine sorbent indicated that the iodine retention capacity of the sorbent was reduced 60% by the TBP and that the column containing iodine sorbent material protected by the alumina TBP sorbent retained 30 times more iodine than the column without TBP sorbent. TBP concentration was up to 500 mg/m 3 . Similar experiments using a 7 wt % Ag impregnated silica gel indicated that the TBP vapor had little effect on the iodine retention of the silica gel material. The stoichiometric maximum amount of iodine was retained by the silica gel material. Further experiments were conducted assessing the effects of NO 2 on iodine retention of this 7 wt % Ag sorbent. After the two columns were loaded with iodine in the presence of TBP (in NPH), one column was subjected to 2 vol % NO 2 in air. From visual comparison of the two columns, it appeared that the NO 2 regenerated the silica gel iodine sorbent and that iodine was washed off the silica gel iodine sorbent leaving the sorbent in the original state

Measurement of tributyl phosphate (TBP) in groundwater at a legacy radioactive waste site and its possible role in contaminant mobilisation.

Science.gov (United States)

Rowling, Brett; Kinsela, Andrew S; Comarmond, M Josick; Hughes, Catherine E; Harrison, Jennifer J; Johansen, Mathew P; Payne, Timothy E

2017-11-01

At many legacy radioactive waste sites, organic compounds have been co-disposed, which may be a factor in mobilisation of radionuclides at these sites. Tri-butyl phosphate (TBP) is a component of waste streams from the nuclear fuel cycle, where it has been used in separating actinides during processing of nuclear fuels. Analyses of ground waters from the Little Forest Legacy Site (LFLS) in eastern Australia were undertaken using solid-phase extraction (SPE) followed by gas chromatographic mass spectrometry (GCMS). The results indicate the presence of TBP several decades after waste disposal, with TBP only being detected in the immediate vicinity of the main disposal area. TBP is generally considered to degrade in the environment relatively rapidly. Therefore, it is likely that its presence is due to relatively recent releases of TBP, possibly stemming from leakage due to container degradation. The ongoing presence and solubility of TBP has the potential to provide a mechanism for nuclide mobilisation, with implications for long term management of LFLS and similar legacy waste sites. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Contribution to the study of uranyl salts in butyl phosphate solutions; Contribution a l'etude des solutions de sels d'uranyle dans les phosphates butyliques

Energy Technology Data Exchange (ETDEWEB)

Coulon, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1965-06-01

A spectroscopic study in the normal infrared region and involving the following associations: tri-alkyl phosphates (tri-butyl, tri-ethyl, tri-methyl), uranyl salts (nitrate, chloride, acetate) has confirmed the existence of an interaction between the phosphoryl group and the uranium atom, as shown by a movement of absorption band for the valency P = 0 from {approx} 1270 cm{sup -1} to {approx} 1180 cm{sup -1}. A study of the preparation, analysis and spectroscopy of the solids obtained by the precipitation of uranyl salts by acid butyl phosphates has been carried out. By infrared spectrophotometry it has been shown that the tri-butyl and di-butyl phosphates are associated in non-polar diluents even before the uranium is introduced. The extraction of uranyl salts from acid aqueous solutions by a diluted mixture of tri-butyl and di-butyl phosphates proceeds by different mechanisms according to the nature of the ion (nitrate or chloride). (author) [French] Une etude spectroscopique dans l'infrarouge moyen portant sur les associations: - phosphates trialcoyliques (tributylique - triethylique - trimethylique) - sels d'uranyle (nitrate, chlorure, acetate) a confirme l'existence d'une interaction entre le groupement phosphoryle et l'atome d'uranium, se manifestant par un deplacement de la bande d'absorption de la vibration de valence P = 0 de {approx} 1270 cm{sup -1} a {approx} 1180 cm{sup -1}. Une etude preparative, analytique et spectroscopique des solides obtenus par precipitation de sels d'uranyle par les phosphates butyliques acides a ete effectuee. La spectrophotomerie infrarouge met en evidence l'association, anterieure a toute introduction d'uranium, des phosphates tributylique et dibutylique dans des diluants non polaires. L'extraction de sels d'uranyle, d'une solution aqueuse acide par un melange dilue de phosphates tributylique et dibutylique, s'effectue suivant des processus differents a la nature de l'anion (nitrate ou chlorure). (auteur)

Investigation of the primary plasticisers present in polyvinyl chloride (PVC) products currently authorised as food contact materials.

Science.gov (United States)

Carlos, Katherine S; de Jager, Lowri S; Begley, Timothy H

2018-03-15

PVC is a common food contact material that is usually plasticised to increase its flexibility. Phthalates are one class of chemical compounds that are often used as plasticisers in PVC in a wide range of industries. They may be used in packaging materials for foods and can also be found in components of certain food processing equipment such as conveyor belts and tubing. Transfer of plasticisers from packaging to foods can occur. In recent years, there has been increased interest in understanding the health effects of phthalates, as well as the possible human exposure levels. However, there is limited information available about the routes of exposure to phthalates. In July 2014, the Chronic Hazard Advisory Panel (CHAP) produced a report for the U.S. Consumer Product Safety Commission detailing the potential health hazards of phthalates and phthalate alternatives. This report listed diet as one factor contributing greater than or equal to 10% of total phthalate exposure. As a result of this report, the U.S. Food and Drug Administration (FDA) is interested in determining the types of the primary plasticiser present in food packaging and processing materials as well as their concentrations. An investigation was conducted of 56 different samples of PVC food packaging and food processing materials available in the US market using a solvent extraction and GC-MS analysis. Nine different plasticisers including three phthalates, di(2-ethylhexyl) phthalate, diisononyl phthalate and diisodecyl phthalate, were identified in the products tested. The plasticiser concentrations ranged from 1 to 53% depending on the types of food contact materials and the type of plasticiser. Overall, it appears that manufacturers are switching away from phthalates as their primary plasticiser to alternate compounds such as ESBO, ATBC, DEHT, DINCH, DEHA and DINA.

The role of calcium ions and lignosulphonate plasticiser in the hydration of cement

International Nuclear Information System (INIS)

Grierson, L.H.; Knight, J.C.; Maharaj, R.

2005-01-01

Experiments involving equilibrium dialysis, conductivity, X-ray diffraction analysis (XRD), differential thermal analysis (DTA) and isothermal titration calorimetry (ITC) have been carried out to investigate the role of calcium ions and polymeric plasticisers in cement/admixture hydration. Results from a study of lignosulphonic acid, sodium salt, acetate as a plasticiser shows that a plasticiser has dual role; one mainly as a kinetic inhibitor (poison) in cement hydration mechanism and the other as a dispersant. Evidence of a weak Ca 2+ binding to lignosulphonate sulphonic moieties was found at low ionic strengths of 0.1 M using ITC. No evidence of formal Ca 2+ binding to lignosulphonate sulphonic acid moieties was found using equilibrium dialysis at higher ionic strength of 1 M (ionic strengths of 0.4 M are typically found in Portland cement pore solution), as is often suggested in cement/admixture literature

Analysis of plasticiser migration to meat roasted in plastic bags by SPME-GC/MS.

Science.gov (United States)

Moreira, Miriany Avelino; André, Leiliane Coelho; Cardeal, Zenilda de Lourdes

2015-07-01

Plasticisers are compounds used in the polymer industry to increase the flexibility of plastics. Some of these compounds cause endocrine dysfunction in humans and animals by interfering with the production, release, transport, metabolism, binding or elimination of natural hormones in the body and are therefore recognised as endocrine disruptors. This paper describes cold-fibre solid-phase microextraction as a sampling technique to analyse eight plasticisers in spices and roasted chicken meat stored in plastic bags by gas chromatography-mass spectrometry. Limits of detection for this method ranged from 0.01 to 0.18 μg kg(-)(1). Diisobutyl phthalate and dibutyl phthalate were found in the samples of spices and roasted chicken meat. The highest concentrations of plasticisers were found in the spices used to cook the chicken meat. Copyright © 2015 Elsevier Ltd. All rights reserved.

Contribution to the study of uranyl salts in butyl phosphate solutions; Contribution a l'etude des solutions de sels d'uranyle dans les phosphates butyliques

Energy Technology Data Exchange (ETDEWEB)

Coulon, A. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1965-06-01

A spectroscopic study in the normal infrared region and involving the following associations: tri-alkyl phosphates (tri-butyl, tri-ethyl, tri-methyl), uranyl salts (nitrate, chloride, acetate) has confirmed the existence of an interaction between the phosphoryl group and the uranium atom, as shown by a movement of absorption band for the valency P = 0 from {approx} 1270 cm{sup -1} to {approx} 1180 cm{sup -1}. A study of the preparation, analysis and spectroscopy of the solids obtained by the precipitation of uranyl salts by acid butyl phosphates has been carried out. By infrared spectrophotometry it has been shown that the tri-butyl and di-butyl phosphates are associated in non-polar diluents even before the uranium is introduced. The extraction of uranyl salts from acid aqueous solutions by a diluted mixture of tri-butyl and di-butyl phosphates proceeds by different mechanisms according to the nature of the ion (nitrate or chloride). (author) [French] Une etude spectroscopique dans l'infrarouge moyen portant sur les associations: - phosphates trialcoyliques (tributylique - triethylique - trimethylique) - sels d'uranyle (nitrate, chlorure, acetate) a confirme l'existence d'une interaction entre le groupement phosphoryle et l'atome d'uranium, se manifestant par un deplacement de la bande d'absorption de la vibration de valence P = 0 de {approx} 1270 cm{sup -1} a {approx} 1180 cm{sup -1}. Une etude preparative, analytique et spectroscopique des solides obtenus par precipitation de sels d'uranyle par les phosphates butyliques acides a ete effectuee. La spectrophotomerie infrarouge met en evidence l'association, anterieure a toute introduction d'uranium, des phosphates tributylique et dibutylique dans des diluants non polaires. L'extraction de sels d'uranyle, d'une solution aqueuse acide par un melange dilue de phosphates tributylique et dibutylique, s'effectue suivant des processus differents a la

Plasticisation and complexation of certain polymers in supercritical CO2

CSIR Research Space (South Africa)

Labuschagne, Philip W

2004-09-01

Full Text Available A polymer system (polyvinylpyrrolidone + polyvinyl acetate-co-crotonic acid) was successfully identified for use as encapsulation material for sensitive actives using supercritical CO2 as plasticisation medium, having the following properties: 1...

Extraction of lithium from salt lake brine using room temperature ionic liquid in tributyl phosphate

International Nuclear Information System (INIS)

Shi, Chenglong; Jia, Yongzhong; Zhang, Chao; Liu, Hong; Jing, Yan

2015-01-01

Highlights: • We proposed a new system for Li recovery from salt lake brine by extraction using an ionic liquid. • Cation exchange was proposed to be the mechanism of extraction followed in ionic liquid. • This ionic liquid system shown considerable extraction ability for lithium and the single extraction efficiency of lithium reached 87.28% under the optimal conditions. - Abstract: Lithium is known as the energy metal and it is a key raw material for preparing lithium isotopes which have important applications in nuclear energy source. In this work, a typical room temperature ionic liquid (RTILs), 1-butyl-3-methyl-imidazolium hexafluorophosphate ([C 4 mim][PF 6 ]), was used as an alternative solvent to study liquid/liquid extraction of lithium from salt lake brine. In this system, the ionic liquid, NaClO 4 and tributyl phosphate (TBP) were used as extraction medium, co-extraction reagent and extractant respectively. The effects of solution pH value, phase ratio, ClO 4 − amount and other factors on lithium extraction efficiency had been investigated. Optimal extraction conditions of this system include the ratio of TBP/IL at 4/1 (v/v), O/A at 2:1, n(ClO 4 − )/n(Li + ) at 2:1, the equilibration time of 10 min and unadjusted pH. Under the optimal conditions, the single extraction efficiency of lithium was 87.28% which was much higher than the conventional extraction system. Total extraction efficiency of 99.12% was obtained by triple-stage countercurrent extraction. Study on the mechanism revealed that the use of ionic liquid increased the extraction yield of lithium through cation exchange in this system. Preliminary results indicated that the use of [C 4 mim][PF 6 ] as an alternate solvent to replace traditional organic solvents (VOCs) in liquid/liquid extraction was very promising

Reactivity of tributyl phosphate degradation products with nitric acid: Relevance to the Tomsk-7 accident

International Nuclear Information System (INIS)

Barney, G.S.; Cooper, T.D.

1995-01-01

The reaction of a degraded tributyl phosphate (TBP) solvent with nitric acid is thought to have caused the chemical explosion at the Tomsk-7 reprocessing plant at Tomsk, Russia in 1993. The estimated temperature of the organic layer was not high eneough to cause significant reaction of nitric acid with TBP or hydrocarbon diluent compounds. A more reactive organic compound was likely present in the organic layer that reacted with sufficient heat generation to raise the temperature to the point where an autocatalytic oxidation of the organic solvent was initiated. Two of the most likely reactive compounds that are present in degraded TBP solvents are n-butanol and n-butyl nitrate. The reactions of these compounds with nitric acid are the subject of this study. The objective of laboratory-scale tests was to identify chemical reactions that occur when n-butanol and n-butyl nitrate contact heated nitric acid solutions. Reaction products were identified and quantitified, the temperatures at which these reactions occur and heats of reaction were measured, and reaction variables (temperature, nitric acid concentration, organic concentration, and reaction time) were evaluated. Data showed that n-butyl nitrate is less reactive than n-butanol. An essentially complete oxidation reaction of n-butanol at 110-120 C produced four major reaction products. Mass spectrometry identified the major inorganic oxidation products for both n-butanol and n-butyl nitrate as nitric oxide and carbon dioxide. Calculated heats of reaction for n-butanol and n-butyl nitrate to form propionic acid, a major reaction product, are -1860 cal/g n-butanol and -953 cal/g n-butyl nitrate. These heats of reaction are significant and could have raised the temperature of the organic layer in the Tomsk-7 tank to the point where autocatalytic oxidation of other organic compounds present resulted in an explosion

The distribution of Th(NO3)4, UO2(NO3)2 and HNO3 between an aqueous phase and an organic tributyl phosphate phase

International Nuclear Information System (INIS)

Nakashima, T.; Zimmer, E.

1984-05-01

The distribution of Th(NO 3 ) 4 , UO 2 (NO 3 ) 2 and HNO 3 between an aqueous phase and an organic phase, consisting of 30 Vol.% tributyl phosphate in dodecane, has been experimentally investigated. About 120 distribution data have been determined in the concentration ranges that can be seen in the THOREX process for reprocessing spent thorium bearing fuel. Based on the experimental data, two computer programs have been developed which make possible interpolations and, to some extent, extrapolations. With model 1, concentrations in the organic phase can be calculated if that in the aqueous phase are known. With model 2, concentrations in the aqueous phase can be calculated vice versa. Besides the description of the calculation models, a large body of calculated data can be found in this report. In a addition, a calculation mode is presented that makes possible the calculation of distribution data for very low thorium concentrations. (orig.) [de

Mutual effect of zinc (2) and cadmium (2) during extraction with tributil phosphate from lithium chloride solutions

International Nuclear Information System (INIS)

Prokuev, V.A.; Belousov, E.A.

1980-01-01

Mutual effect of zinc and cadmium chlorides during extraction with tributyl phosphate at 5, 25 and 45 deg C from LiCl solutions is studied. The conclusion about the suppression of zinc and cadmium extraction by extracting macroelement (cadmium and zinc correspondingly) as the result of manifestation of general ion effect (lithium ion) in the extraction systems is made. It is established that the suppression of zink and cadmium extraction increases with the temperature decrease. On the base of the obtained experimental data the different type of extraction element distribution curves at the extraction from the muriatic solutions and lithium chloride solutions with tributyl phosphate is discussed

Degradation studies on plasticised PVC films submitted to gamma radiation

International Nuclear Information System (INIS)

Vinhas, Gloria Maria; Souto-Maior, Rosa Maria; Lapa, Camila Maria; Almeida, Yeda Medeiros Bastos de

2003-01-01

Poly (vinyl chloride), PVC, is a rigid polymer and for several of its applications must be compounded with plasticizing agents. The plasticizers minimize the dipolar interactions, which exist between the polymer's chains, promoting their mobility. In this work we studied the properties of PVC/plasticizer systems submitted to different doses of gamma radiation. We have used four commercial plasticizers among them di(2-ethylhexyl) phthalate, DEHP, which is present in a great number of commercial applications. The PVC/plasticizer systems have been studied as films made by the solvent evaporation technique. Irradiated and non-irradiated films have been characterized by viscosimetric analysis, mechanical essays and infrared spectroscopy. The results have shown that the rigid, non plasticized, PVC film presented the greatest degradation index, while among the plasticised films the one which presented the larger degradation index due to chain scission was the DEHP plasticised PVC. (author)

Different characteristic effects of ageing on starch-based films plasticised by 1-ethyl-3-methylimidazolium acetate and by glycerol.

Science.gov (United States)

Zhang, Binjia; Xie, Fengwei; Zhang, Tianlong; Chen, Ling; Li, Xiaoxi; Truss, Rowan W; Halley, Peter J; Shamshina, Julia L; McNally, Tony; Rogers, Robin D

2016-08-01

The focus of this study was on the effects of plasticisers (the ionic liquid 1-ethyl-3-methylimidazolium acetate, or [Emim][OAc]; and glycerol) on the changes of starch structure on multiple length scales, and the variation in properties of plasticised starch-based films, during ageing. The films were prepared by a simple melt compression moulding process, followed by storage at different relative humidity (RH) environments. Compared with glycerol, [Emim][OAc] could result in greater homogeneity in [Emim][OAc]-plasticised starch-based films (no gel-like aggregates and less molecular order (crystallites) on the nano-scale). Besides, much weaker starch-starch interactions but stronger starch-[Emim][OAc] interactions at the molecular level led to reduced strength and stiffness but increased flexibility of the films. More importantly, [Emim][OAc] (especially at high content) was revealed to more effectively maintain the plasticised state during ageing than glycerol: the densification (especially in the amorphous regions) was suppressed; and the structural characteristics especially on the nano-scale were stabilised (especially at a high RH), presumably due to the suppressed starch molecular interactions by [Emim][OAc] as confirmed by Raman spectroscopy. Such behaviour contributed to stabilised mechanical properties. Nonetheless, the crystallinity and thermal stability of starch-based films with both plasticisers were much less affected by ageing and moisture uptake during storage (42 days), but mostly depended on the plasticiser type and content. As starch is a typical semi-crystalline bio-polymer containing abundant hydroxyl groups and strong hydrogen bonding, the findings here could also be significant in creating materials from other similar biopolymers with tailored sensitivity and properties to the environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Extraction of lithium from salt lake brine using room temperature ionic liquid in tributyl phosphate

Energy Technology Data Exchange (ETDEWEB)

Shi, Chenglong [Key Laboratory of Salt Lake Resources and Chemistry, Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, 810008 Xining (China); University of Chinese Academy of Sciences, 100049 Beijing (China); Jia, Yongzhong [Key Laboratory of Salt Lake Resources and Chemistry, Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, 810008 Xining (China); Zhang, Chao [Key Laboratory of Salt Lake Resources and Chemistry, Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, 810008 Xining (China); University of Chinese Academy of Sciences, 100049 Beijing (China); Liu, Hong [Qinghai Salt Chemical Products Supervision and Inspection Center, 816000 Golmud (China); Jing, Yan, E-mail: 1580707906@qq.com [Key Laboratory of Salt Lake Resources and Chemistry, Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, 810008 Xining (China)

2015-01-15

Highlights: • We proposed a new system for Li recovery from salt lake brine by extraction using an ionic liquid. • Cation exchange was proposed to be the mechanism of extraction followed in ionic liquid. • This ionic liquid system shown considerable extraction ability for lithium and the single extraction efficiency of lithium reached 87.28% under the optimal conditions. - Abstract: Lithium is known as the energy metal and it is a key raw material for preparing lithium isotopes which have important applications in nuclear energy source. In this work, a typical room temperature ionic liquid (RTILs), 1-butyl-3-methyl-imidazolium hexafluorophosphate ([C{sub 4}mim][PF{sub 6}]), was used as an alternative solvent to study liquid/liquid extraction of lithium from salt lake brine. In this system, the ionic liquid, NaClO{sub 4} and tributyl phosphate (TBP) were used as extraction medium, co-extraction reagent and extractant respectively. The effects of solution pH value, phase ratio, ClO{sub 4}{sup −} amount and other factors on lithium extraction efficiency had been investigated. Optimal extraction conditions of this system include the ratio of TBP/IL at 4/1 (v/v), O/A at 2:1, n(ClO{sub 4}{sup −})/n(Li{sup +}) at 2:1, the equilibration time of 10 min and unadjusted pH. Under the optimal conditions, the single extraction efficiency of lithium was 87.28% which was much higher than the conventional extraction system. Total extraction efficiency of 99.12% was obtained by triple-stage countercurrent extraction. Study on the mechanism revealed that the use of ionic liquid increased the extraction yield of lithium through cation exchange in this system. Preliminary results indicated that the use of [C{sub 4}mim][PF{sub 6}] as an alternate solvent to replace traditional organic solvents (VOCs) in liquid/liquid extraction was very promising.

Synthesis of xLiMnPO4·yLi3V2(PO43/C Nanocomposites for Lithium Ion Batteries Using Tributyl Phosphate as Phosphor Source

Directory of Open Access Journals (Sweden)

Yanming Wang

2017-01-01

Full Text Available The xLiMnPO4·yLi3V2(PO43/C (x/y = 1 : 0, 12 : 1, 8 : 1, 6 : 1, 4 : 1, 0 : 1 composite cathode materials are synthesized using tributyl phosphate as a novel organic phosphor source via a solid-state reaction process. All obtained xLiMnPO4·yLi3V2(PO43/C composites present similar particles morphology with an average size of ca. 100 nm and low extent agglomeration. The electrochemical performance of pristine LiMnPO4/C can be effectively improved by adding small amounts of Li3V2(PO43 additives. The 4LiMnPO4·Li3V2(PO43/C has a high discharge capacity of 143 mAh g−1 at 0.1 C and keeps its 94% at the end of 100 cycles.

Recovery of uranium from wet process by the chloridic leaching of phosphate rocks

International Nuclear Information System (INIS)

Santana, A.O.; Paula, H.C.B.; Dantas, C.C.

1984-01-01

Uranium was recovered from chloridic leach liquor of phosphate rocks by solvent extraction on a laboratory scale. The extractor system is a mixture of di-(2-ethylhexyl) phosphoric acid (D 2 EHPA) and tributyl-phosphate (TBP) in a varsol diluent. The uranium concentration is 150 ppm in the rocks and 12 ppm in the leach liquor. The phosphate rocks are leached on a semi-industrial scale for dicalcium phosphate production. The recovery process comprises the following steps: extraction, reextraction, iron removal and uranium precipitation. (orig./EF)

Recovery of uranium from wet process by the chloridic leaching of phosphate rocks

Energy Technology Data Exchange (ETDEWEB)

Santana, A O; Paula, H C.B.; Dantas, C C

1984-03-01

Uranium was recovered from chloridic leach liquor of phosphate rocks by solvent extraction on a laboratory scale. The extractor system is a mixture of di-(2-ethylhexyl) phosphoric acid (D/sub 2/EHPA) and tributyl-phosphate (TBP) in a varsol diluent. The uranium concentration is 150 ppm in the rocks and 12 ppm in the leach liquor. The phosphate rocks are leached on a semi-industrial scale for dicalcium phosphate production. The recovery process comprises the following steps: extraction, reextraction, iron removal and uranium precipitation.

Alternate extractants to tributyl phosphate for reactor fuel reprocessing

International Nuclear Information System (INIS)

Crouse, D.J.; Arnold, W.D.; Hurst, F.J.

1983-01-01

Both tri(n-hexyl) phosphate (THP) and tri(2-ethylhexyl) phosphate (TEHP) have some important potential process advantages over TBP for reactor fuel reprocessing. These include negligible aqueous phase solubility and less tendency toward third phase and crud formation. The alkyl chain branching of TEHP makes it much more stable to chemical degradation than TBP and probably also accounts for its much weaker ruthenium extraction. The higher uranium and plutonium extraction power of THP and TEHP allows higher solvent loadings in extraction but makes them somewhat more difficult to strip. The phase separation properties of 1.09 M solutions of THP and TEHP are inferior to those of 1.09 M TBP (30 vol %) but are favorable at lower concentrations. Use of more dilute THP and TEHP solutions is recommended for this reason and to obtain a better balance of extraction power in the extraction versus stripping steps

Plasticisation of amylodextrin by moisture. Consequences for compaction behaviour and tablet properties

NARCIS (Netherlands)

Steendam, R; Frijlink, H W; Lerk, C F

2001-01-01

Purpose: Amylodextrin, a starch-based controlled release excipient, spontaneously absorbs moisture during storage. The aim of this study was to investigate plasticisation of amylodextrin by moisture and its effect on compaction and tablet characteristics. Methods: The glass transition temperature

Exchange reactions between a molten salt and a solution of tri-butyl phosphate in a liquid silicone; Reactions d'echange entre un sel fondu et une solution de phosphate de tributyle dans un silicone liquide

Energy Technology Data Exchange (ETDEWEB)

Hertzog, D [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Present interest centred around molten salts can be explained by their possible use in the field of nuclear energy, in particular as a support for fuels and also as reprocessing agents. It seemed of interest to consider the molten salt as a solvent and to study partition phenomena with a second phase stable at high temperatures. The salt chosen is a ternary eutectic of alkali nitrates and the second phase is a solution of tri-butyl phosphate in a liquid silicone. The working temperature is fixed at 150 deg. C. We have studied first of all the stability of the two phases and their mutual solubilities at this temperature. It has been shown that the two solvents are immiscible and stable. We have also described the extraction by the silicone solution of various products in solution in the salt phase, and have determined the partition coefficients and the formulae of the extracted molecules. It has been possible to calculate the partition coefficients of the following ions extracted as nitrates: Li{sup +}, Na{sup +}, K{sup +}, Sr{sup 2+}, Ca{sup 2+}, Ba{sup 2+}, Hg{sup 2+} whose partition coefficients are very low: Mg{sup 2+}, Ni{sup 2+}, Co{sup 2+}, Zn{sup 2+} whose extraction yields are greater than 50 per cent; finally Ce{sup 3+}, La{sup 3+}, UO{sub 2}{sup 2+}, highly extracted. Also the following anions have been extracted in the form of alkali salts: F{sup -}, Cl{sup -}, Br{sup -}, I{sup -}, IO{sub 3}{sup -}, CN{sup -}, SO{sub 4}{sup -}, C{sub 2}O{sub 4}{sup -}, NO{sub 2}{sup -}. Amongst these, only the halogens have non-negligible partition coefficients. In certain particular cases we have been able to study the influence of complex formation on the extraction phenomena. Two applications are described: - The separation of two products by complex formation and extraction (separation of magnesium from cobalt, nickel and zinc); - The calculation of the equilibrium constant of a complex by measurement of the variation in the partition coefficient of the ion complexed

Lack of genotoxic potential of acetylated monoglyceride: An alternative plasticiser to phthalates

DEFF Research Database (Denmark)

Mortensen, Alicja; Wedebye, Eva Bay; Niemelä, Jay Russell

2011-01-01

Purpose: With a yearly polymer production of more than 400 million tons, phthalates based on non sustainable petrochemical materials are the most used group of plasticisers. Their low biodegradability and endocrine activity suspected to affect reproductive ability of animals and humans caused...

A comparative study on cellulose nanocrystals extracted from bleached cotton and flax and used for casting films with glycerol and sorbitol plasticisers.

Science.gov (United States)

Csiszár, Emilia; Nagy, Sebestyén

2017-10-15

Cellulose nanocrystals (CNCs) were released from bleached cotton and flax by a sulphuric acid hydrolysis with about 40 and 34% yield, respectively. The rod-like cotton-CNC particles were slightly longer and wider and had a less pronounced aggregation ability in aqueous suspension than the flax-CNC ones. Films were cast from the CNC suspensions with sorbitol and glycerol plasticisers. The concept behind this research was to explore how the plasticisers - with similar structure but different molecular weight - and their concentrations affect the perceptible and measured properties of CNC films. Results revealed that the type of plasticiser determined the morphology and the optical and tensile properties of films. The best quality CNC film with an averaged thickness of 50μm was obtained with 20% sorbitol from cotton-CNC. It was proved that behaviour of sorbitol and glycerol plasticisers in CNC films was very similar to that reported previously for starch films. Copyright © 2017 Elsevier Ltd. All rights reserved.

Calculation of concentration profiles and their experimental verification with a pulsed sieve-plate column and the reactive material system of uranyl nitrate, nitric acid/tributyl phosphate, kerosine

International Nuclear Information System (INIS)

Ihle, E.

1985-01-01

The present study is concerned with the calculation of stationary and non-stationary concentration profiles as well as with the starting and disturbance behaviour of a pulsed sieve-plate extraction column. It investigates into the material system HNO 3 /uranyl nitrate in water with 30 per cent by volume of tributyl phosphate in kerosine. During the measurements of the concentration profiles for HNO 3 transition, which were effected in the direction of extraction and reextraction, it was shown that the concentration profiles measured in the mixer-settler range, in spite of a sixfold enlargement of the specific heat transfer area, do not differ essentially from those measured in the dispersion range. During the measurements of concentration profiles for HNO 3 /uranium transition, which were effected in the direction of coextraction and co-reextraction only for mixer-settler range, it was discovered that with increasing phase ratios, there is a depletion of the uranium concentration in the aqueous phase. If the phase ratio is further raised, it is the nitric acid, and not the uranium, that is depleted. (orig./PW) [de

A Hydrogen Ion-Selective Sensor Based on Non-Plasticised Methacrylic-acrylic Membranes

Directory of Open Access Journals (Sweden)

Musa Ahmad

2002-08-01

Full Text Available A methacrylic-acrylic polymer was synthesised for use as a non-plasticised membrane for hydrogen ion-selective sensor incorporating tridodecylamine as an ionophore. The copolymer consisted of methyl methacrylate and n-butyl acrylate monomers in a ratio of 2:8. Characterisation of the copolymer using FTNMR demonstrated that the amount of each monomer incorporated during solution polymerisation was found to be similar to the amount used in the feed before polymerisation. The glass transition temperature of the copolymer determined by differential scanning calorimetry was -30.9 ºC. Potentiometric measurements conducted showed a linear pH response range of 4.3 – 9.6 with the response slope of 56.7 mV/decade. The selectivity of the sensors towards hydrogen ions was similar to other plasticiser based membrane electrodes and the logarithmic selectivity coefficients for discrimination against interference cations is close to –9.7. However, the incorporation of a lipophilic anion as membrane additive is essential in ensuring optimum performance of the hydrogen ion sensor.

Effect of Gamma Radiation on the Chemical and Physical Properties of Plasticised Carboxymethyl Cellulose (Cc) / Poly (vinyl alcohol)(Pva) Polymer Blend

International Nuclear Information System (INIS)

El-Salmawi, M.K.; Abu Zaid, M.M.; Ibraheim, M.S.; El-Nagger Abdel Wahab, M.; Zahran Abdel Hamid, H.

2000-01-01

The chemical and physical properties of plasticizer carboxymethyl cellulose (CMC)/ poly (vinylalcohol)(PVA) polymer blend before and after exposure to gamma ray were investigated by means of mechanical properties, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscope (SEM). It was found that addition of plasticizer causes a significant increase in elongation at break and causes a marked drop in thermal stability. Thus, the addition of glycerol cause a significant decrease in glass transition temperature(Tg) of about 24 degree from the initial value. The morphological structure of plasticised blend was investigated by observation of fracture surfaces using SEM. The plasticised blend was used for recovery of some heavy metals from their salts such as Cu(II), Co(II) and Ni(II). It was found that plasticised blend have a great ability for absorbing these metals and it is measured by compleximetric titration and colour strength measurements

Uranium recovery in a pilot plant as by product of the phosphate fertilizers

International Nuclear Information System (INIS)

Dantas, C.C.; Santos, F.S.M. dos; Paula, H.C.B.; Santana, A.O. de

1984-01-01

A process was developed and a piloto plant was installed to recovery uranium from chloridric leach liquor of phosphate rocks. The extractor system is a mixture of di(2-ethylhexyl) phosphoric acid (DEHPA) and tributyl-phosphate (TBP) in a kerosene diluent. The phosphate rocks are leached for dicalcium phosphate (CaHPO 4 ) production, by the reactions: Ca 3 (PO 4 ) 2 + 4 HCl → Ca(H 2 PO 4 ) 2 + CaCl 2 and Ca(H 2 PO 4 ) 2 + Ca(OH) 2 → CaHPO 4 + 2 H 2 O. The uranium recovery process comprises the following steps:extraction, scrubbing, reextraction, iron removal and uranium precipitation. The uranium is precipited as ADU with 80% of U 3 O 8 .(Author) [pt

The synthesis and characterization of tributyl phosphate grafted carbon nano-tubes by the floating catalytic chemical vapor deposition method and their sorption behavior towards uranium

International Nuclear Information System (INIS)

Shruti Mishra; Jaya Dwivedi; Amar Kumar; Nalini Sankararamakrishnan

2016-01-01

Carbon nano-tubes (CNTs) were synthesized by the floating catalytic chemical vapor deposition technique using ferrocene in benzene as the hydrocarbon source. The functionalization of CNTs was carried out by oxidation (CNT-OX) and grafting with a tributyl phosphate (TBP) ligand (CNT-TBP). Various spectroscopic techniques including scanning electron microscopy (SEM), Fourier Transform Infra Red Spectroscopy (FTIR), BET surface area and X-ray photoelectron spectroscopy (XPS) were used to characterize the adsorbents. FTIR and XPS studies revealed the efficient grafting of the TBP ligand on the CNT surface. The effect of the initial pH and the contact time for the maximum adsorption of U(VI) with CNT-plain, CNT-OX and CNT-TBP was studied. The spontaneity of the sorption was confirmed by thermodynamic data. A pseudo second order model with a regression coefficient of ≥0.978 was obtained for CNT-TBP and equilibrium was reached within 3 h. The Langmuir maximum adsorption capacity of U(VI) at pH 5 for CNT, CNT-OX and CNT-TBP was found to be 66.6, 100.0 and 166.6 mg.g -1 respectively. Using 0.1 M HCl as a de-sorbent, recyclability studies were carried out for three cycles. The probable mechanism of adsorption between U(VI) and CNT-TBP could be understood through FTIR and XPS techniques. (authors)

Biphasic kinetic investigations on the evaluation of non-salt forming reductants for Pu(IV) stripping from tributyl phosphate and N,N-dihexyl octanamide solutions in n-dodecane

International Nuclear Information System (INIS)

Prabhu, D.R.; Neelam Kumari; Kanekar, A.S.; Pathak, P.N.

2013-01-01

The relative stability of different oxidation states of actinide elements is influenced by the nature of complexes formed and redox equilibria in aqueous/non-aqueous solutions. The reduction/stripping studies on Pu(IV) ions from loaded organic phases of 1.1 M tributyl phosphate and of 1.1 M N,N-dihexyl octanamide in n-dodecane were studied using organic soluble tert-butyl hydroquinone (TBH) and aqueous soluble reductants like acetaldoxime (AX) and hydroxyurea (HU). These studies were carried out as a function of reductant and nitric acid concentration (0.5-4 M HNO 3 ) and of time. The changes in Pu oxidation states were followed by spectrophotometry for TBH and by distribution ratio values for AX and HU as reductants. Spectrophotometric investigations using TBH as reductant showed that it was desirable to strip Pu(III) formed after reduction of Pu(IV) in the organic phase, which may otherwise be reconverted to extractable Pu(IV) by in situ generated HNO 2 from oxidative degradation of TBH to tert-butyl quinone. Similarly, the biphasic reduction/stripping of Pu(IV) using AX and HU as reductant rate was affected adversely with increased aqueous phase acidity. This data will help in the accurate simulation of Pu separation processes using these reductants in mixer-settlers/pulsed columns or centrifugal contactors. (author)

Effect of Cambi Thermal Hydrolysis Process-Anaerobic digestion treatment on concentrations on phthalate plasticisers in wastewater sludge

Science.gov (United States)

The impact of the recently implemented Cambi Thermal Hydrolysis Process™-Anaerobic Digestion (TH-AD) solids treatment method on concentrations of 4 phthalate plasticisers in wastewater sludge samples was explored in this study. Samples were analysed for diisononyl phthalate (DiNP), diisodecyl phthal...

Investigation of antimony extraction from nitric acid solutions by tributyl phosphate

International Nuclear Information System (INIS)

Lakaev, V.S.; Smelov, V.S.

1988-01-01

The effect of iodide, hydrogen and pertechnetate ions on antimony extraction by tri-n-butyl phosphate (TBP) from aqueous nitric acid solutions under irradiated nuclear fuel processing is investigated at room temperature. The coefficients of antimony distribution are shown to increase at the presence of technetium ions 2-3 times and iodine ions - 100 and more times. Variation of hydrogen ion concentration does not affect antimony extraction. The schemes of the mechanism of antimony extraction at the pressence of iodide and pertechnetate ions are presented. Compositions of the formed compounds are given

Determination of Phthalate Plasticisers in Palm Oil Using Online Solid Phase Extraction-Liquid Chromatography (SPE-LC

Directory of Open Access Journals (Sweden)

Nazarudin Ibrahim

2014-01-01

Full Text Available Contamination of phthalates plasticisers to food has raised concern as some of the phthalates are suspected to be endocrine disruptors. The phthalates have high affinity with oily environment and analysing these chemicals in such matrices is difficult because of the trace amount of the analyte and interference from matrix. An online solid phase extraction (SPE technique using a large volume (3.5 mL injection was developed for the analysis of 6 common plasticisers in palm oil. A simple sample preparation involving alumina as a fat retainer and methanol : acetonitrile (1 : 1 as the extraction solvent was performed prior to the usage of online SPE-LC system. This system consists of two columns, C16 for the solid phase extraction (SPE and C18 as the analytical column, and a photo diode array detector. The calibration curves were linear from 5 to 1000 μg L−1, with correlation coefficients above 0.99. The instrumental limit of detection was 3 μg L−1 and satisfactory recovery was obtained. A screening on a few samples in the retail market revealed the presence of dibutyl phthalate (DBP and butylbenzylphthalate (BBP in the palm oil, with concentration less than 1 mg L−1.

Effect of epoxidised soybean oil loading as plasticiser on physical, mechanical and thermal properties of polyvinylchloride

Science.gov (United States)

Rahmah, M.; Nurazzi, N. Mohd; Farah Nordyana, A. R.; Syed Anas, S. M.

2017-07-01

The aim of this paper is to study the effect of epoxidised soybean oil (ESO) as an alternative plasticizer on physical, mechanical and thermal properties of plasticised polyvinyl chloride (PPVC). Samples were prepared using 10, 20, 30 and 40% by weight percent of ESO. The samples were characterized for density, water absorption, tensile, hardness and thermal properties. The addition of ESO as plasticizer in PVC had caused significant effect on the physical and mechanical properties of PPVC. Increasing of ESO loading had resulted in decreased density, tensile strength, tensile modulus but increased in elongation at break and shore hardness. From water absorption study, it was observed that the all the samples reached the plateau absorption at days 8 to 10 with absorption percentages of between 1.8 to 2%. In general the crystallinity of PPVC maintained between 10 to 13% with increase in ESO loading while the melting point ( Tm) is slightly decreased about 3 to 6°C. In this study, ESO which acts as plasticiser were found to result in lower glass transition temperature (Tg). The enhancements of super cooling with higher ESO loading were found to increase the crystallization temperature, promoting crystallisation and act as nucleating agent.

Supported liquid inorganic membranes for nuclear waste separation

Science.gov (United States)

Bhave, Ramesh R; DeBusk, Melanie M; DelCul, Guillermo D; Delmau, Laetitia H; Narula, Chaitanya K

2015-04-07

A system and method for the extraction of americium from radioactive waste solutions. The method includes the transfer of highly oxidized americium from an acidic aqueous feed solution through an immobilized liquid membrane to an organic receiving solvent, for example tributyl phosphate. The immobilized liquid membrane includes porous support and separating layers loaded with tributyl phosphate. The extracted solution is subsequently stripped of americium and recycled at the immobilized liquid membrane as neat tributyl phosphate for the continuous extraction of americium. The sequestered americium can be used as a nuclear fuel, a nuclear fuel component or a radiation source, and the remaining constituent elements in the aqueous feed solution can be stored in glassified waste forms substantially free of americium.

Physicochemical characteristics and sorption capacities of heavy metal ions of activated carbons derived by activation with different alkyl phosphate triesters

Science.gov (United States)

Wang, Jing; Liu, Hai; Yang, Shaokun; Zhang, Jian; Zhang, Chenglu; Wu, Haiming

2014-10-01

Five alkyl phosphate triesters (APTEs), including trimethyl phosphate (TMP), triethyl phosphate (TEP), triisopropyl phosphate (TPP), tributyl phosphate (TBP) and trioctyl phosphate (TOP), were used as activating agents for preparing activated carbons (AC-APTEs) with high surface acidity and metal ion sorption capacity. N2 adsorption/desorption isotherms, surface morphologies, elemental compositions, results of Boehm's titration and sorption capacities of heavy metal ions of the carbons were investigated. AC-APTEs contained much more acidic groups and exhibited much less surface area (phosphoric acid activation. For the AC-APTEs, AC-TOP had the highest surface area (488 m2/g), AC-TMP showed the highest yield (41.1%), and AC-TBP possessed the highest acidic groups (2.695 mmol/g), oxygen content (47.0%) and metal ion sorption capacities (40.1 mg/g for Ni(II) and 53.5 mg/g for Cd(II)). For the carbons, AC-APTEs showed much larger Ni(II) and Cd(II) sorption capacities than AC-PPA, except AC-TPP. The differences of the carbons in the physicochemical and sorption properties suggested surface chemistry of the carbons was the main factor influencing their sorption capacities whereas the pore structure played a secondary role.

Exposure of aircraft maintenance technicians to organophosphates from hydraulic fluids and turbine oils: a pilot study.

Science.gov (United States)

Schindler, Birgit Karin; Koslitz, Stephan; Weiss, Tobias; Broding, Horst Christoph; Brüning, Thomas; Bünger, Jürgen

2014-01-01

Hydraulic fluids and turbine oils contain organophosphates like tricresyl phosphate isomers, triphenyl phosphate and tributyl phosphate from very small up to high percentages. The aim of this pilot study was to determine if aircraft maintenance technicians are exposed to relevant amounts of organophosphates. Dialkyl and diaryl phosphate metabolites of seven organophosphates were quantified in pre- and post-shift spot urine samples of technicians (N=5) by GC-MS/MS after solid phase extraction and derivatization. Pre- and post shift values of tributyl phosphate metabolites (dibutyl phosphate (DBP): median pre-shift: 12.5 μg/L, post-shift: 23.5 μg/L) and triphenyl phosphate metabolites (diphenyl phosphate (DPP): median pre-shift: 2.9 μg/L, post-shift: 3.5 μg/L) were statistically higher than in a control group from the general population (median DBP: <0.25 μg/L, median DPP: 0.5 μg/L). No tricresyl phosphate metabolites were detected. The aircraft maintenance technicians were occupationally exposed to tributyl and triphenyl phosphate but not to tricresyl phosphate, tri-(2-chloroethyl)- and tri-(2-chloropropyl)-phosphate. Further studies are necessary to collect information on sources, routes of uptake and varying exposures during different work tasks, evaluate possible health effects and to set up appropriate protective measures. Copyright © 2013 Elsevier GmbH. All rights reserved.

Criticality safety of solvent extraction process

International Nuclear Information System (INIS)

Tachimori, Shoichi; Miyoshi, Yoshinori

1987-01-01

The article presents some comments on criticality safety of solvent extraction processes. When used as an extracting medium, tributyl phosphate extracts nitric acid and water, in addition to nitrates of U and Pu, into the organic phase. The amount of these chemical species extracted into the organic phase is dependent on and restricted by the concentrations of tributyl phosphate and other components. For criticality control, measures are taken to decrease the concentration of tributyl phosphate in the organic phase, in addition to control of the U and Pu concentrations in the feed water phase. It should be remembered that complexes of tributyl phosphate with nitrates of such metals as Pu(IV), Pu(VI), U(IV) and Th(IV) do not dissolve uniformly in the organic phase. In criticality calculation for solution-handling systems, U and Pu are generally assumed to have a valence of 6 and 4, respectively. In the reprocessing extraction process, however, U and Pu can have a valence of 4, and 3 and 6, respectively. The organic phase and aqueous phase contact in a counter-current flow. U and Pu will be accumulated if they are not brought out of the extraction system by this flow. (Nogami, K.)

Influence of nitric acid on the kinetic of complexation of uranyl nitrate extracted by TBP

International Nuclear Information System (INIS)

Pushlenkov, M.F.; Zimenkov, V.V.

1982-02-01

The effect of nitric acid on the solvatation rate of uranyl nitrate with tributyl phosphate is studied. In the process of mass transfer, it is shown that nitric acid enables the extraction of uranyl nitrate, therefore its concentration in the organic phase exceeds that in equilibrium solution. Subsequently uranyl nitrate ''displaces'' nitric acid. The presence of the acid in aqueous and organic phases affects in a complicated manner the rate of solvatation of uranyl nitrate with tributyl phosphate [fr

Markers of anthropogenic contamination: A validated method for quantification of pharmaceuticals, illicit drug metabolites, perfluorinated compounds, and plasticisers in sewage treatment effluent and rain runoff.

Science.gov (United States)

Wilkinson, John L; Swinden, Julian; Hooda, Peter S; Barker, James; Barton, Stephen

2016-09-01

An effective, specific and accurate method is presented for the quantification of 13 markers of anthropogenic contaminants in water using solid phase extraction (SPE) followed by high performance liquid chromatography (HPLC) tandem mass spectrometry (MS/MS). Validation was conducted according to the International Conference on Harmonisation (ICH) guidelines. Method recoveries ranged from 77 to 114% and limits of quantification between 0.75 and 4.91 ng/L. A study was undertaken to quantify the concentrations and loadings of the selected contaminants in 6 sewage treatment works (STW) effluent discharges as well as concentrations in 5 rain-driven street runoffs and field drainages. Detection frequencies in STW effluent ranged from 25% (ethinylestradiol) to 100% (benzoylecgonine, bisphenol-A (BPA), bisphenol-S (BPS) and diclofenac). Average concentrations of detected compounds in STW effluents ranged from 3.62 ng/L (ethinylestradiol) to 210 ng/L (BPA). Levels of perfluorinated compounds (PFCs) perfluorooctanoic acid (PFOA) and perfluorononanoic acid (PFNA) as well as the plasticiser BPA were found in street runoff at maximum levels of 1160 ng/L, 647 ng/L and 2405 ng/L respectively (8.52, 3.09 and 2.7 times more concentrated than maximum levels in STW effluents respectively). Rain-driven street runoff may have an effect on levels of PFCs and plasticisers in receiving rivers and should be further investigated. Together, this method with the 13 selected contaminants enables the quantification of various markers of anthropogenic pollutants: inter alia pharmaceuticals, illicit drugs and their metabolites from humans and improper disposal of drugs, while the plasticisers and perfluorinated compounds may also indicate contamination from industrial and transport activity (street runoff). Copyright © 2016 Elsevier Ltd. All rights reserved.

Simulation of the plant uptake of organophosphates and other emerging pollutants for greenhouse experiments and field conditions

DEFF Research Database (Denmark)

Trapp, Stefan; Eggen, Trine

2013-01-01

The uptake of the organophosphates tris(2-chloroethyl) phosphate (TCEP), tris(1-chloro-2-propyl) phosphate (TCPP), tributyl phosphate (TBP), the insect repellant N,N-diethyl toluamide (DEET), and the plasticizer n-butyl benzenesulfonamide (NBBS) into plants was studied in greenhouse experiments...

Extraction spectrophotometric analyzer

International Nuclear Information System (INIS)

Batik, J.; Vitha, F.

1985-01-01

Automation is discussed of extraction spectrophotometric determination of uranium in a solution. Uranium is extracted from accompanying elements in an HCl medium with a solution of tributyl phosphate in benzene. The determination is performed by measuring absorbance at 655 nm in a single-phase ethanol-water-benzene-tributyl phosphate medium. The design is described of an analyzer consisting of an analytical unit and a control unit. The analyzer performance promises increased productivity of labour, improved operating and hygiene conditions, and mainly more accurate results of analyses. (J.C.)

Application of the alpha spectrometry for the study of core sediment extracted in the San Marcos dam in Chihuahua

Energy Technology Data Exchange (ETDEWEB)

Mendez G, C.; Renteria V, M.; Montero C, M. E. [Centro de Investigacion en Materiales Avanzados, S. C., Miguel de Cervantes No. 120, Complejo Industrial Chihuahua, 31109 Chihuahua (Mexico); Garcia T, R., E-mail: elena.montero@cimav.edu.mx [Universidad de Sevilla, Escuela Tecnica Superior de Arquitectura, Grupo de Fisica Nuclear Aplicada, Av. Reina Mercedes s/n, 41012 Sevilla (Spain)

2012-06-15

The determination of the specific activities of {sup 210}Po and isotopic uranium by alpha spectrometry was performed in a sediment core from San Marcos Dam. The objective of this work was to analyze the vertical distribution of isotopic uranium and {sup 210}Po and the behavior of these radionuclides along sediment core collected from the San Marcos Dam. Sample was divided into 11 sections, in which {sup 210}Po and isotopic uranium were determined using liquid-liquid extraction with tributyl phosphate. Furthermore, it was made a comparison between the tributyl phosphate technique and the technique of extraction chromatography using UTEVA resins for uranium. The results of specific activities for {sup 210}Po show a trend to decrease along the core, whereas the uranium isotopic does not show a pointed trend. The results of isotopic ratios between the {sup 234}U and {sup 238}U show that they are close to secular equilibrium in each of the core sections. The comparison between the two uranium extraction techniques indicates that the chemical yield is better using the UTEVA technique than tributyl phosphate extraction. (Author)

Application of the alpha spectrometry for the study of core sediment extracted in the San Marcos dam in Chihuahua

International Nuclear Information System (INIS)

Mendez G, C.; Renteria V, M.; Montero C, M. E.; Garcia T, R.

2012-01-01

The determination of the specific activities of 210 Po and isotopic uranium by alpha spectrometry was performed in a sediment core from San Marcos Dam. The objective of this work was to analyze the vertical distribution of isotopic uranium and 210 Po and the behavior of these radionuclides along sediment core collected from the San Marcos Dam. Sample was divided into 11 sections, in which 210 Po and isotopic uranium were determined using liquid-liquid extraction with tributyl phosphate. Furthermore, it was made a comparison between the tributyl phosphate technique and the technique of extraction chromatography using UTEVA resins for uranium. The results of specific activities for 210 Po show a trend to decrease along the core, whereas the uranium isotopic does not show a pointed trend. The results of isotopic ratios between the 234 U and 238 U show that they are close to secular equilibrium in each of the core sections. The comparison between the two uranium extraction techniques indicates that the chemical yield is better using the UTEVA technique than tributyl phosphate extraction. (Author)

40 CFR 799.4360 - Tributyl phosphate.

Science.gov (United States)

2010-07-01

... substance shall be applied to the intact clipped skin (approximately 2 cm2 for rats, 40 cm2 for mini-pigs... cells from the test solution shall be done using an ultrafiltration (e.g., 0.45 micrometer pore size...

46 CFR 30.25-1 - Cargoes carried in vessels certificated under the rules of this subchapter.

Science.gov (United States)

2010-10-01

... Alcohols (C13+) Cetyl-Stearyl alcohol), see Alcohols (C13+) III † Coal tar A Copper salt of long chain (C17... Pentene (all isomers) C n-Pentyl propionate C Petrolatum III 1-Phenyl-1-xylyl ethane C Phosphate esters..., see Triisopropylated phenyl phosphates Tributyl phosphate B Tricresyl phosphate (less than 1% of the...

Ionophore-Based Potentiometric Sensors for the Flow-Injection Determination of Promethazine Hydrochloride in Pharmaceutical Formulations and Human Urine

Directory of Open Access Journals (Sweden)

Suad Mustafa Al-Araji

2011-01-01

Full Text Available Plasticised poly(vinyl chloride-based membranes containing the ionophores (α-, β- and γ-cyclodextrins (CD, dibenzo-18-crown-6 (DB18C6 and dibenzo-30-crown-10 (DB30C10 were evaluated for their potentiometric response towards promethazine (PM in a flow injection analysis (FIA set-up. Good responses were obtained when β- and γ-CDs, and DB30C10 were used. The performance characteristics were further improved when tetrakis(4-chlorophenyl borate (KTPB was added to the membrane. The sensor based on β-CD, bis(2-ethylhexyl adipate (BEHA and KTPB exhibited the best performance among the eighteen sensor compositions that were tested. The response was linear from 1 x 10−5 to 1 x 10−2 M, slope was 61.3 mV decade−1, the pH independent region ranged from 4.5 to 7.0, a limit of detection of 5.3 x 10−6 M was possible and a lifetime of more than a month was observed when used in the FIA system. Other plasticisers such as dioctyl phenylphosphonate and tributyl phosphate do not show significant improvements in the quality of the sensors. The promising sensors were further tested for the effects of foreign ions (Li+, Na+, K+, Mg2+, Ca2+, Co2+, Cu2+, Cr3+, Fe3+, glucose, fructose. FIA conditions (e.g., effects of flow rate, injection volume, pH of the carrier stream were also studied when the best sensor was used (based on β-CD. The sensor was applied to the determination of PM in four pharmaceutical preparations and human urine that were spiked with different levels of PM. Good agreement between the sensor and the manufacturer’s claimed values (for pharmaceutical preparations was obtained, while mean recoveries of 98.6% were obtained for spiked urine samples. The molecular recognition features of the sensors as revealed by molecular modelling were rationalised by the nature of the interactions and complexation energies between the host and guest molecules.

Influence of Methacrylic-Acrylic Copolymer Composition on Plasticiser-free Optode Films for pH Sensors

Directory of Open Access Journals (Sweden)

Musa Ahmad

2003-03-01

Full Text Available In this work we have examined the use of plasticiser-free polymeric films incorporating a proton selective chromoionophore for optical pH sensor. Four types of methacrylic-acrylic copolymers containing different compositions of n-butyl acrylate (nBA and methyl methacrylate (MMA were synthesised for use as optical sensor films. The copolymers were mixed with appropriate amounts of chromoionophore (ETH5294 and a lipophilic salt before spin coated on glass slides to form films for the evaluation of pH response using spectrophotometry. Co-polymer films with high nBA content gave good response and the response time depended on the film thickness. A preliminary evaluation of the optical films of high nBA content with pHs from 2 - 14 showed distinguishable responses from pH 5 - 9. However, the adhesion of the pH sensitive film was good for copolymers with higher content of MMA but not for films with high nBA.

Behavior of Nb fission product during nuclear fuel reprocessing

International Nuclear Information System (INIS)

Gue, J.P.

1977-02-01

Investigations on niobium fission product behavior in nitric acid and tributyl phosphate media have been carried out in order to explain the difficulties encountered in separating this element from fissile materials during spent nuclear fuel reprocessing. The studies have shown that in nitric acid solution, pentavalent niobium has a colloidal hydroxide form. The so-obtained sols were characterized by light scattering, electronic microscopy, electrophoresis and ultracentrifugation methods. In heterogeneous extracting media containing tributyl phosphate and dibutyl phosphoric acid the niobium hydroxide sols could be flocculated by low dibutyl phosphoric acid concentration or extracted into the organic phase containing an excess of dibutyl phosphoric acid [fr

Study on the effect of gamma radiolysis on the chromatographic composition profile of tri-isoAmyl-phosphate-n-dodecane-nitric acid system

International Nuclear Information System (INIS)

Chaudhary, S.D.; Lokhande, Manisha; Bindu, M.; Tripathi, S.C.; Gandhi, P.M.

2013-01-01

Tri-Iso-Amyl phosphate (TiAP), a higher homologue of tri-butyl phosphate (TBP) is the solvent proposed for the reprocessing of the spent nuclear fuel of Fast Breeder Reactors (FBR) origin. TiAP-n-dodecane has extraction behavior comparable to that of TBP-n-dodecane system, without third phase formation and an aqueous solubility ∼ 19mg/L, that is far too less in case as compared to that with TBP(∼400gm/L). We have initiated our study to examine the radiolytic degradation behavior of TiAP-n-dodecane in comparison to that of TBP and explore its full potential for reprocessing of spent nuclear fuels. A 30% mixture of TiAP with n-dodecane equilibrated with nitric acid of concentrations 2M has been subjected to steady state gamma radiolysis using 60 Co source. The samples were irradiated for increasing absorbed dose of 6,12 and 18M rad. Each of these samples were subjected to gas chromatographic analysis under optimised condition using thermal conductivity detector. Separately, these samples were also methylated using diazomethane for the determination of acidic phosphate species as their volatile methyl ester

Device for separating ruthenium ion from spent fuel material

International Nuclear Information System (INIS)

Izumida, Tatsuo; Sasahira, Akira; Ozawa, Yoshihiro; Kawamura, Fumio.

1988-01-01

Purpose: To separate plutonium ions efficiently and selectively from organic solvent containing tributyl phosphate used in the main step of reprocessing process. Constitution: The device comprises, as the main constituent factor, a liquid-liquid contact device for bringing not water soluble organic solvent into contact with a nitric acid solution of spent fuel substances and a liquid-liquid contact-separation device for bringing an organic solvent solution containing spent fuel substances separated with nitric acid into contact again with nitric acid. Then, a device is disposed between two liquid-liquid contact devices for staying ruthenium ions and organic solvent for a sufficient time. In this way, ruthenium ions in the organic solvent containing butyl phosphate are gradually converted into complex compounds combined with tributyl phosphate thereby enabling to separate ruthenium ions efficiently and remarkably reduce the corrosion of equipments. (Horiuchi, T.)

Recovery of uranium and lanthanides during the production of nitrophosphate fertilizers using tertiary amyl alcohol

Energy Technology Data Exchange (ETDEWEB)

Habashi, F; Awadalla, F T

1986-01-01

When phosphate rock is dissolved in nitric acid, phosphoric acid and uranium can be selectively extracted by tertiary amyl alcohol; other impurities including the lanthanides remain in the aqueous phase. Uranium can be recovered from the alcohol phase by selective stripping and the lanthanides from the raffinate by extraction with tributyl phosphate.

Glycerol-plasticised silk membranes made using formic acid are ductile, transparent and degradation-resistant.

Science.gov (United States)

Allardyce, Benjamin J; Rajkhowa, Rangam; Dilley, Rodney J; Redmond, Sharon L; Atlas, Marcus D; Wang, Xungai

2017-11-01

Regenerated silk fibroin membranes tend to be brittle when dry. The use of plasticisers such as glycerol improve membrane ductility, but, when combined with aqueous processing, can lead to a higher degradation rate than solvent-annealed membranes. This study investigated the use of formic acid as the solvent with glycerol to make deformable yet degradation-resistant silk membranes. Here we show that membranes cast using formic acid had low light scattering, with a diffuse transmittance of less than 5% over the visible wavelengths, significantly lower than the 20% transmittance of aqueous derived silk/glycerol membranes. They had 64% β-sheet content and lost just 30% of the initial silk weight over 6h when tested with an accelerated enzymatic degradation assay, in comparison the aqueous membranes completely degraded within this timeframe. The addition of glycerol also improved the maximum elongation of formic acid derived membranes from under 3% to over 100%. They also showed good cytocompatibility and supported the adhesion and migration of human tympanic membrane keratinocytes. Formic acid based, silk/glycerol membranes may be of great use in medical applications such as repair of tympanic membrane perforation or ocular applications where transparency and resistance to enzymatic degradation are important. Copyright © 2017 Elsevier B.V. All rights reserved.

Estimation of solubility of organo-phosphorus extractants by P determination using molybdovanadophosphoric acid method

International Nuclear Information System (INIS)

Gill, J.S.; Kotekar, M.K.; Singh, H.

2005-01-01

Solvent extraction processes have been found to be suitable for uranium recovery from phosphoric acid. Various extractants like di-2-ethyl hexylphosphoric acid (D2EHPA), di-nonylphenyl phosphoric acid (DNPPA) and synergistic agents like tri-butyl phosphate (TBP), tri-octyl phosphine oxide (TOPO) have been used in liquid-liquid extraction of uranium from phosphoric acid. Contents of these organo-phosphorus compounds in aqueous raffinates need estimation for process requirements. Solubility of Tri-butyl phosphate (TBP) and Di-2-ethylhexyl phosphoric acid (D2EHPA) extractants have been determined in different media of water, oxalic acid (0.6M) and sulphuric acid (3.75M) solutions. These compounds were estimated by determining their phosphorus (P) contents employing molybdovanadophosphoric acid method, after digesting and solubalizing them in nitric and perchloric acid. (author)

Rare earth elements materials production from apatite ores

International Nuclear Information System (INIS)

Anufrieva, A V; Buynovskiy, A S; Makaseev, Y N; Mazov, I N; Nefedov, R A; Sachkov, V I; Valkov, A V; Andrienko, O S; Stepanova, O B

2016-01-01

The paper deals with the study of processing apatite ores with nitric acid and extraction of the rare earth elements. The rare earth elements can be successfully separated and recovered by extraction from the nitrate- phosphate solution, being an tributyl phosphate as extraction agent. The developed scheme of the processing apatite concentrate provides obtaining rare earth concentrates with high qualitative characteristics. (paper)

Treatment of organic waste solutions containing tributyl phosphate

International Nuclear Information System (INIS)

Drobnik, S.

The two processes developed in the laboratory for treating waste solutions containing TBP, namely TBP separation with phosphoric acid and saponification were tested on a semi-industrial scale. A waste solution from the first phase of the Karlsruhe reprocessing plant was used

Nonaqueous chlorination of uranium metal in tributyl phosphate

International Nuclear Information System (INIS)

Buchikhin, E.P.; Kuznetsov, A.Yu.; Shatalov, V.V.; Vidanov, V.L.; Chekmarev, A.M.

2005-01-01

Low-temperature (30-50 deg C) chlorination of uranium metal in the TBP-TCE-Cl 2 system (TCE = tetrachloroethylene) was studied. Dissolution of uranium in the dipolar aprotic solvent proceeds with formation of U(IV) compounds. The activation energy of this process is 31.24 kJ mol -1 , and relative reaction order with respect to Cl 2 is 2. The effect of TBP concentration on chlorination was examined. The chlorination rate sharply increases at a water content in the TBP-TCE system of 0.2- 0.6 vol % [ru

Development of plasticised nano-biocomposites of poly(hydroxybutyrate-co-hydroxyvalerate)/montmorillonite organically modified (PHBV/OMMT)

International Nuclear Information System (INIS)

Correa, M.C.; Pollet, E.; Averous, L.; Agnell, J.A.M.; Nascente, P.A.P.

2010-01-01

Several studies have aimed to improve the properties of biopolymers by the incorporation of nano-sized fillers, such as organo-modified montmorillonite (OMMT), to form nano-biocomposites. The objective of this work is to investigate the influence of acetyl tributyl citrate (ATBC) plasticizer with PHBV/OMMT nano-biocomposites aiming at improving their behavior. The materials PHBV, OMMT (C30B), and ATBC were provided by PHB Industrial S/A (Brazil), Southern Clay Products (USA), and Scandiflex S/A (Brazil), respectively. In this study the processing parameters and the formulations were controlled, pursuing materials with good mechanical and barrier properties with high biodegradability and with greater ease of processing. The analysis of the results obtained by TGA, GPC, WAXS, DSC, mechanical properties, and biodegradability lead to the conclusion that the addition of plasticizer in nanobiocomposites improved processability and did not influence the state of nano-sized load dispersion. It can be concluded that the addition of plasticizer is a good alternative to the processability of nanocomposites of PHAs. (author)

Courtland Target Assembly Facility Environmental Assessment

Science.gov (United States)

2006-10-01

Draft Environmental Assessment 2-17 tributyl phosphate (TBP)6, diatomaceous earth, talcum powder, cornmeal , water, steel, and plastic. 2.2.2... cornmeal , water, steel, and plastic that would not qualify as hazardous materials. TBP is non-explosive, non-flammable, and stable under normal

Method of manufacturing ceramic oxide nuclear fuels and intermediate products thereof

International Nuclear Information System (INIS)

Matous, V.; Pecak, V.; Baran, V.

1978-01-01

Uranyl nitrate or uranyl sulphate is extracted as a tributyl phosphate solvate into an organic solvent from aqueous solutions of uranium in sulphuric or nitric acid obtained from ore treatment or from wet reprocessing. Uranyl fluorides obtained from dry reprocessing should be hydrolysed and converted to uranyl sulphate or uranyl nitrate for such extraction. The tributyl phosphate solvate of the compound in the organic solvent (in a higher petrol fraction or in a chlorinated hydrocarbon) is directly precipitated using an aqueous solution of a hydroxide, preferably ammonium hydroxide as a hydrated oxide. Stoichiometric and overstoichiometric amounts of hydroxides lead to the formation of amorphous diuranates. Substoichiometric amounts of hydroxides used and of hydroxylamine solutions only lead to hydrolysis in which heavy macroscopic yellow crystalline precipitates are formed of the hydrated uranium oxide. Drying and annealing may result in UO 3 and UO 2 , respectively. (B.S.)

TBP and diluent mass balances in the PUREX Plant at Hanford, 1955--1991

International Nuclear Information System (INIS)

Sederburg, J.P.; Reddick, J.A.

1994-12-01

The purpose of this report is to develop an estimate of the quantities of tributyl phosphate and diluent discharged in aqueous waste streams to the tank farms from the Hanford Purex Plant over its operating life. Purex was not the sole source of organics in the tank farms, but was a major contributor. Tributyl phosphate (TBP) and diluent, which changed from Shell E-2342 reg-sign to Soltrol-170 reg-sign and then to normal paraffin hydrocarbon (NPH), were organic chemicals used in the Purex solvent extraction process at Hanford to separate plutonium and uranium from spent nuclear fuels. This report is an estimate of the material balances for these chemicals in the Purex Plant at Hanford over its entire operating life. The Purex Plant had cold start up in November 1955 and shut down in 1990. It's process used a solution of 30 vol% TBP in diluent

Recovery of acid-degraded tributyl phosphate by solvent extraction

International Nuclear Information System (INIS)

Young, G.C.; Holladay, D.W.

1981-01-01

During nuclear fuel reprocessing the organic solvent becomes loaded with various acidic degradation products, which can be effectively removed through solvent extraction. Studies have been made with a small bench-scale solvent extraction system to optimize such parameters as pH of aqueous phase, phase ratio, residence time, flow rates, and temperature. The necessary decontamination factors have been obtained for various degradation products during continuous solvent extraction in one stage, with the aqueous phase being recycled. The aqueous phase contains compounds that can be degraded to gases to minimize waste disposal problems

Processing of Phosphorus Slag with Recovery of Rare Earth Metals and Obtaining Silicon Containing Cake

Science.gov (United States)

Karshigina, Zaure; Abisheva, Zinesh; Bochevskaya, Yelena; Akcil, Ata; Sharipova, Aynash; Sargelova, Elmira

2016-10-01

The present research is devoted to the processing of slag generating during the yellow phosphorus production. In this paper are presented studies on leaching of phosphorus production slag by nitric acid with recovery of rare earth metals (REMs) into solution. REMs recovery into the solution achieved 98 % during the leaching process with using 7.5 mol/L of HNO3, liquid-to-solid ratio is 2.6:1, temperature is 60°C, process duration is 1 hour and stirrer speed is 500 rpm. Behaviour during the leaching of associated components such as calcium, aluminium, and iron was studied. After the leaching cake contains ∼⃒75-85 % of SiO2 and it might be useful for obtaining of precipitated silicon dioxide. With the purpose of separation from the impurities, recovery and concentrating of REMs, the obtained solution after leaching was subjected to extraction processing methods. The influence of ratio of organic and aqueous phases (O: A) on the extraction of rare earth metals by tributyl phosphate (TBP) with concentrations from 20 up to 100 % was studied. The REMs extraction with increasing TBP concentration under changes O:A ratio from 1:20 down to 1:1 into the organic phase from the solutions after nitric acid leaching increased from 22.2 up to 99.3%. The duration effect of REMs extraction process was studied by tributyl phosphate. It is revealed that with increasing of duration of the extraction process from 10 to 30 minutes REMs recovery into the organic phase almost did not changed. The behaviour of iron in the extraction process by TBP was studied. It was found that such accompanying components as calcium and aluminium by tributyl phosphate didn't extracted. To construct isotherm of REMs extraction of by tributyl phosphate was used variable volume method. It was calculated three-step extraction is needed for REMs recovery from the solutions after nitric acid leaching of phosphorus production slag. The process of the three-steps counter current extraction of rare earth

Raman imaging using fixed bandpass filter

Science.gov (United States)

Landström, L.; Kullander, F.; Lundén, H.; Wästerby, P.

2017-05-01

By using fixed narrow band pass optical filtering and scanning the laser excitation wavelength, hyperspectral Raman imaging could be achieved. Experimental, proof-of-principle results from the Chemical Warfare Agent (CWA) tabun (GA) as well as the common CWA simulant tributyl phosphate (TBP) on different surfaces/substrates are presented and discussed.

Assessment of the mechanisms involved in the removal of emerging contaminants by microalgae from wastewater: a laboratory scale study.

Science.gov (United States)

Matamoros, Víctor; Uggetti, Enrica; García, Joan; Bayona, Josep M

2016-01-15

Aerated batch reactors (2.5L) fed either with urban or synthetic wastewater were inoculated with microalgae (dominated by Chlorella sp. and Scenedesmus sp.) to remove caffeine, ibuprofen, galaxolide, tributyl phosphate, 4-octylphenol, tris(2-chloroethyl) phosphate and carbamazepine for 10 incubation days. Non-aerated and darkness reactors were used as controls. Microalgae grew at a rate of 0.25 d(-1) with the complete removal of N-NH4 during the course of the experiment. After 10 incubation days, up to 99% of the microcontaminants with a Henry's law constant higher than 3 10(-1) Pa m(3) mol(-1) (i.e., 4-octylphenol, galaxolide, and tributyl phosphate) were removed by volatilization due to the effect of air stripping. Whereas biodegradation was effective for removing ibuprofen and caffeine, carbamazepine and tris(2-chloroethyl) phosphate behaved as recalcitrant compounds. The use of microalgae was proved to be relevant for increasing the biodegradation removal efficiency of ibuprofen by 40% and reducing the lag phase of caffeine by 3 days. Moreover, the enantioselective biodegradation of S-ibuprofen suggested a biotic prevalent removal process, which was supported by the identification of carboxy-ibuprofen and hydroxy-ibuprofen. The results from microalgae reactors fed with synthetic wastewater showed no clear evidences of microalgae uptake of any of the studied microcontaminants. Copyright © 2015 Elsevier B.V. All rights reserved.

Separation of zirconium and hafnium using paper distribution chromatography

International Nuclear Information System (INIS)

Lebedeva, G.G.; Viktorova, M.E.

1981-01-01

A method is suggested of chromatographic separation of zirconium and hafnium in a CCl 4 -tributyl phosphate system (1:9) containing KCl as a salting-out agent in 5 M HNO 3 at 28-30 deg C. Zr and Hf are deterfmined in articiial mixtures under optimal chromatography conditions using visual colorimetry [ru

Extraction-spectrophotometric method for silicon determination in high-purity substances. 1. Silicon determination in tellurium

Energy Technology Data Exchange (ETDEWEB)

Shaburova, V P; Yudelevich, I G [AN SSSR, Novosibirsk (USSR). Inst. Neorganicheskoj Khimii

1989-01-01

The extraction-spectrophotometric method for silicon determination in tellurium based on extraction isolation of the base by tributyl phosphate from hydrochloride solutions and with addition of HNO/sub 3/ and spectrophotometric silicon determination using malachite green is developed. The method permits to determine 2x10/sup -1/-3x10/sup -4/ % Si.

Reaction of iodine oxidation by potassium permanganate in tributyl phosphate

International Nuclear Information System (INIS)

Khokhlov, M.L.; Legin, E.K.

1990-01-01

Stoichiometry was determined and kinetics of iodine oxidation by potassium permanganate in tributylphosphate was studied. Kinetic scheme, which agrees with stoichiometry and experimental kinetic equation of the reaction, is suggested. A mixture is the reaction product. It is ascertained that when the mixture is heated, thermal decomposition of iodate to iodide occurs without elementary iodine separation, which is catalyzed by polymanganate

Treatment of tributyl phosphate wastes by extraction cum pyrolysis process

International Nuclear Information System (INIS)

Deshingkar, D.S.; Ramaswamy, M.; Kartha, P.K.S.; Kutty, P.V.E.; Ramanujam, A.

1989-01-01

For the treatment of spent tri n-butyl phospate (TBP) wastes from Purex process, a method involving extraction of TBP with phosphoric acid followed by pyrolysis of TBP - phosphoric acid phase was investigated. The process was examined with respect to simulated waste, process solvent wastes and aged organic waste samples. These studies seem to offer a simple treatment method for the separation of bulk of diluent from spent solvent wastes. The diluent phase needs further purification for reuse in reprocessing plant; otherwise it can be incinerated. (author). 18 refs., 3 tabs., 6 figs

Synergistic solvent extraction of Co(III) by thenoyltrifluoroacetone and some organophosphorous compounds

International Nuclear Information System (INIS)

El-Naggar, H.A.; Maghrawy, H.B.; Ramadan, A.

1983-01-01

The extraction of Co(III) from aceticacid-acetate buffer solutions with various mixtures of ligands has been studied. Thenoyltrifluoroacetone mixed with triphenylphosphine oxide, trioctylphosphine oxide or tributyl phosphate were used as extractants. The effect of different parameters affecting the distribution ratio was studied in detail. Also, the corresponding thermodynamic parameters are calculated and discussed, together with the structures of extracted species. (author)

Operating conditions of T.B.P. line uranium purification plant, for uranium dioxide production

International Nuclear Information System (INIS)

Vardich, R.N.; La Gamma, A.M.; Anasco, R.; Soler, S.M.G. de; Isnardi, E.; Gea, V.; Chiaraviglio, R.; Matyjasczyk, E.; Aramayo, R.

1992-01-01

In this contribution are presented the operative conditions and the results obtained step of the Uranium dioxide production plant of Argentina. The refining step involve the Uranium concentrate dissolution, the silica ageing, the filtration and liquid - liquid extraction with n-tributyl phosphate solution in kerosene. The established operative conditions allow to obtain Uranyl nitrate solutions of nuclear purity in industrial scale. (author)

The SX Solver: A Computer Program for Analyzing Solvent-Extraction Equilibria: Version 3.0

International Nuclear Information System (INIS)

Lumetta, Gregg J.

2001-01-01

A new computer program, the SX Solver, has been developed to analyze solvent-extraction equilibria. The program operates out of Microsoft Excel and uses the built-in Solver function to minimize the sum of the square of the residuals between measured and calculated distribution coefficients. The extraction of nitric acid by tributyl phosphate has been modeled to illustrate the programs use

Adsorption decontamination of radioactive waste solvent by activated alumina and bauxites

International Nuclear Information System (INIS)

Hassan, N.M.; Marra, J.C.; Kyser, E.A.

1994-01-01

An adsorption process utilizing activated alumina and activated bauxite adsorbents was evaluated as a function of operating parameters for the removal of low level radioactive contaminants from organic waste solvent generated in the fuel reprocessing facilities and support operations at Savannah River Site. The waste solvent, 30% volume tributyl phosphate in n-paraffin diluent, was degraded due to hydrolysis and radiolysis reactions of tributyl phosphate and n-paraffin diluent, producing fission product binding degradation impurities. The process, which has the potential for removing these activity-binding degradation impurities from the solvent, was operated downflow through glass columns packed with activated alumina and activated bauxite adsorbents. Experimental breakthrough curves were obtained under various operating temperatures and flow rates. The results show that the adsorption capacity of the activated alumina was in the order 10 4 dpm/g and the capacity of the activated bauxite was 10 5 dpm/g. The performance of the adsorption process was evaluated in terms of dynamic parameters (i.e. adsorption capacity, the height and the efficiency of adsorption zone) in such a way as to maximize the adsorption capacity and to minimize the height of the mass transfer or adsorption zone

The incorporation of low and medium level radioactive wastes (solids and liquids) in cement

International Nuclear Information System (INIS)

Brown, D.J.; Capp, P.D.; Smith, D.L.

1982-08-01

Laboratory studies and mixing plant trials on simulated radioactive waste formulations are reported. Long term stability testing of various formulations including those containing blast furnace slag-ordinary Portland cement, sodium nitrate, ion exchange resins, and sodium nitrate-tributyl phosphate, are reported and some results are given. Mixing plant trials with a high shear cement mixer are reported. An outline of future work is presented. (U.K.)

Construction Materials for Coastal Structures.

Science.gov (United States)

1983-02-01

formaldehyde derivatives. Thermoplastic materials include polyvinyl alcohol and polyacrylamides. PPCC process technology is based upon overcoming the...entrained air from a concrete mixture. Compounds such as tributyl phosphate, diburyl phthalate, water-insoluble alcohols , and water-insoluble esters of...of hydrolysis of wood is small and is dependent on the temperature. 0 (3) Wood Oxidation. Wood oxydation by air in dry locations is slow and attacks

Synergistic Extraction of Copper from Nitrate Solutions Using β-Hydroxy-Naphthaldoxime and Organophosphorus Compounds into Carbon-Tetrachloride

Science.gov (United States)

Dey, Pulak; Basu, Sukalyan

2011-12-01

The extraction behavior of Cu(II) from an aqueous nitrate medium employing β-hydroxy-naphthaldoxime in carbon tetrachloride has been investigated in the presence of several organophosphorus donors like tri-octyl phosphine oxide, tri-butyl phosphine oxide, and tri-butyl phosphate at pH 1.5. The concentration of the metal was measured by atomic absorption spectrophotometry. Synergism was observed when neutral donor was added because of the formation of the adduct [Cu(L)2.(S)] in CCl4 (S denotes neutral donor). The equilibrium constants of the binary system using β-hydroxy-naphthaldoxime and the ternary system involving another addition of an organophosphorus compound were calculated from the extraction date obtained. Furthermore, the temperature dependence of the equilibrium constants was also investigated to evaluate standard enthalpy (Δ H°), entropy (Δ S°), and free energy (Δ G°) of the reactions proposed.

Assessment of the mechanisms involved in the removal of emerging contaminants by microalgae from wastewater: a laboratory scale study

International Nuclear Information System (INIS)

Matamoros, Víctor; Uggetti, Enrica; García, Joan; Bayona, Josep M.

2016-01-01

Highlights: • The effect of microalage on the removal of emerging contaminants has been evaluated. • Volatilization was relevant for compounds with a moderate Henry’s law constant. • Biodegradation was the main factor for the removal of caffeine and ibuprofen. • Ibuprofen enantioselective biodegradation was observed. • CA-ibuprofen and OH-ibuprofen followed the concentration decline of ibuprofen. - Abstract: Aerated batch reactors (2.5 L) fed either with urban or synthetic wastewater were inoculated with microalgae (dominated by Chlorella sp. and Scenedesmus sp.) to remove caffeine, ibuprofen, galaxolide, tributyl phosphate, 4-octylphenol, tris(2-chloroethyl) phosphate and carbamazepine for 10 incubation days. Non-aerated and darkness reactors were used as controls. Microalgae grew at a rate of 0.25 d −1 with the complete removal of N-NH 4 during the course of the experiment. After 10 incubation days, up to 99% of the microcontaminants with a Henry’s law constant higher than 3 10 −1 Pa m 3 mol −1 (i.e., 4-octylphenol, galaxolide, and tributyl phosphate) were removed by volatilization due to the effect of air stripping. Whereas biodegradation was effective for removing ibuprofen and caffeine, carbamazepine and tris(2-chloroethyl) phosphate behaved as recalcitrant compounds. The use of microalgae was proved to be relevant for increasing the biodegradation removal efficiency of ibuprofen by 40% and reducing the lag phase of caffeine by 3 days. Moreover, the enantioselective biodegradation of S-ibuprofen suggested a biotic prevalent removal process, which was supported by the identification of carboxy-ibuprofen and hydroxy-ibuprofen. The results from microalgae reactors fed with synthetic wastewater showed no clear evidences of microalgae uptake of any of the studied microcontaminants.

Analysis of uranium concentrates by atomic-absorption spectrometry

International Nuclear Information System (INIS)

Naeem, M.; Capdevila, C.; Alduan, F.A.

1977-01-01

The determination of As, Ca, Fe, Mo and V in uranium concentrates, removing the bulk of the uranium matrix by extracting with tributyl phosphate in hexane has been tried. No interferences were found due to uranium, sodium, aluminium, sulfates and phosphates. Only for calcium a depressive effect of aluminium and uranium has been found and it is overcome by addition of lanthanum. Air-acetylene flame for Fe, Ca and As, and nitrous oxide-acetylene flame for Mo and V have been used. The considered concentration range has been 0.15 - 3% for Ca and Fe, 0.1 -2% for As and 0.1 - 1% for Mo and V. (author) [es

Phosphorus release from phosphate rock and iron phosphate by low-molecular-weight organic acids.

Science.gov (United States)

Xu, Ren-kou; Zhu, Yong-guan; Chittleborough, David

2004-01-01

Low-molecular-weight(LMW) organic acids widely exist in soils, particularly in the rhizosphere. A series of batch experiments were carried out to investigate the phosphorus release from rock phosphate and iron phosphate by low-molecular-weight organic acids. Results showed that citric acid had the highest capacity to solubilize P from both rock and iron phosphate. P solubilization from rock phosphate and iron phosphate resulted in net proton consumption. P release from rock phosphate was positively correlated with the pKa values. P release from iron phosphate was positively correlated with Fe-organic acid stability constants except for aromatic acids, but was notcorrelated with pKa. Increase in the concentrations of organic acids enhanced P solubilization from both rock and iron phosphate almost linearly. Addition of phenolic compounds further increased the P release from iron phosphate. Initial solution pH had much more substantial effect on P release from rock phosphate than from iron phosphate.

NIOSH Manual of Analytical Methods (third edition). Fourth supplement

Energy Technology Data Exchange (ETDEWEB)

1990-08-15

The NIOSH Manual of Analytical Methods, 3rd edition, was updated for the following chemicals: allyl-glycidyl-ether, 2-aminopyridine, aspartame, bromine, chlorine, n-butylamine, n-butyl-glycidyl-ether, carbon-dioxide, carbon-monoxide, chlorinated-camphene, chloroacetaldehyde, p-chlorophenol, crotonaldehyde, 1,1-dimethylhydrazine, dinitro-o-cresol, ethyl-acetate, ethyl-formate, ethylenimine, sodium-fluoride, hydrogen-fluoride, cryolite, sodium-hexafluoroaluminate, formic-acid, hexachlorobutadiene, hydrogen-cyanide, hydrogen-sulfide, isopropyl-acetate, isopropyl-ether, isopropyl-glycidyl-ether, lead, lead-oxide, maleic-anhydride, methyl-acetate, methyl-acrylate, methyl-tert-butyl ether, methyl-cellosolve-acetate, methylcyclohexanol, 4,4'-methylenedianiline, monomethylaniline, monomethylhydrazine, nitric-oxide, p-nitroaniline, phenyl-ether, phenyl-ether-biphenyl mixture, phenyl-glycidyl-ether, phenylhydrazine, phosphine, ronnel, sulfuryl-fluoride, talc, tributyl-phosphate, 1,1,2-trichloro-1,2,2-trifluoroethane, trimellitic-anhydride, triorthocresyl-phosphate, triphenyl-phosphate, and vinyl-acetate.

Removal of phosphate from solution by adsorption and precipitation of calcium phosphate onto monohydrocalcite.

Science.gov (United States)

Yagi, Shintaro; Fukushi, Keisuke

2012-10-15

The sorption behavior and mechanism of phosphate on monohydrocalcite (CaCO(3)·H(2)O: MHC) were examined using batch sorption experiments as a function of phosphate concentrations, ionic strengths, temperatures, and reaction times. The mode of PO(4) sorption is divisible into three processes depending on the phosphate loading. At low phosphate concentrations, phosphate is removed by coprecipitation of phosphate during the transformation of MHC to calcite. The sorption mode at the low-to-moderate phosphate concentrations is most likely an adsorption process because the sorption isotherm at the conditions can be fitted reasonably with the Langmuir equation. The rapid sorption kinetics at the conditions is also consistent with the adsorption reaction. The adsorption of phosphate on MHC depends strongly on ionic strength, but slightly on temperature. The maximum adsorption capacities of MHC obtained from the regression of the experimental data to the Langmuir equation are higher than those reported for stable calcium carbonate (calcite or aragonite) in any conditions. At high phosphate concentrations, the amount of sorption deviates from the Langmuir isotherm, which can fit the low-to-moderate phosphate concentrations. Speciation-saturation analyses of the reacted solutions at the conditions indicated that the solution compositions which deviate from the Langmuir equation are supersaturated with respect to a certain calcium phosphate. The obtained calcium phosphate is most likely amorphous calcium phosphate (Ca(3)(PO(4))(2)·xH(2)O). The formation of the calcium phosphate depends strongly on ionic strength, temperature, and reaction times. The solubility of MHC is higher than calcite and aragonite because of its metastability. Therefore, the higher solubility of MHC facilitates the formation of the calcium phosphates more than with calcite and aragonite. Copyright © 2012 Elsevier Inc. All rights reserved.

Phosphate Recovery From Sewage Sludge Containing Iron Phosphate

NARCIS (Netherlands)

Wilfert, P.K.

2018-01-01

The scope of this thesis was to lay the basis for a phosphate recovery technology that can be applied on sewage sludge containing iron phosphate. Such a technology should come with minimal changes to the existing sludge treatment configuration while keeping the use of chemicals or energy as small as

Assessment of the mechanisms involved in the removal of emerging contaminants by microalgae from wastewater: a laboratory scale study

Energy Technology Data Exchange (ETDEWEB)

Matamoros, Víctor, E-mail: victor.matamoros@idaea.csic.es [Department of Environmental Chemistry, IDAEA–CSIC, c/Jordi Girona, 18-26, E-08034 Barcelona (Spain); Uggetti, Enrica; García, Joan [GEMMA—Group of Environmental Engineering and Microbiology, Department of Hydraulic, Maritime and Environmental Engineering, Universitat Politècnica de Catalunya BarcelonaTech, c/Jordi Girona, 1-3, Building D1, E-08034 Barcelona (Spain); Bayona, Josep M. [Department of Environmental Chemistry, IDAEA–CSIC, c/Jordi Girona, 18-26, E-08034 Barcelona (Spain)

2016-01-15

Highlights: • The effect of microalage on the removal of emerging contaminants has been evaluated. • Volatilization was relevant for compounds with a moderate Henry’s law constant. • Biodegradation was the main factor for the removal of caffeine and ibuprofen. • Ibuprofen enantioselective biodegradation was observed. • CA-ibuprofen and OH-ibuprofen followed the concentration decline of ibuprofen. - Abstract: Aerated batch reactors (2.5 L) fed either with urban or synthetic wastewater were inoculated with microalgae (dominated by Chlorella sp. and Scenedesmus sp.) to remove caffeine, ibuprofen, galaxolide, tributyl phosphate, 4-octylphenol, tris(2-chloroethyl) phosphate and carbamazepine for 10 incubation days. Non-aerated and darkness reactors were used as controls. Microalgae grew at a rate of 0.25 d{sup −1} with the complete removal of N-NH{sub 4} during the course of the experiment. After 10 incubation days, up to 99% of the microcontaminants with a Henry’s law constant higher than 3 10{sup −1} Pa m{sup 3} mol{sup −1} (i.e., 4-octylphenol, galaxolide, and tributyl phosphate) were removed by volatilization due to the effect of air stripping. Whereas biodegradation was effective for removing ibuprofen and caffeine, carbamazepine and tris(2-chloroethyl) phosphate behaved as recalcitrant compounds. The use of microalgae was proved to be relevant for increasing the biodegradation removal efficiency of ibuprofen by 40% and reducing the lag phase of caffeine by 3 days. Moreover, the enantioselective biodegradation of S-ibuprofen suggested a biotic prevalent removal process, which was supported by the identification of carboxy-ibuprofen and hydroxy-ibuprofen. The results from microalgae reactors fed with synthetic wastewater showed no clear evidences of microalgae uptake of any of the studied microcontaminants.

Phosphate-a poison for humans?

Science.gov (United States)

Komaba, Hirotaka; Fukagawa, Masafumi

2016-10-01

Maintenance of phosphate balance is essential for life, and mammals have developed a sophisticated system to regulate phosphate homeostasis over the course of evolution. However, due to the dependence of phosphate elimination on the kidney, humans with decreased kidney function are likely to be in a positive phosphate balance. Phosphate excess has been well recognized as a critical factor in the pathogenesis of mineral and bone disorders associated with chronic kidney disease, but recent investigations have also uncovered toxic effects of phosphate on the cardiovascular system and the aging process. Compelling evidence also suggests that increased fibroblastic growth factor 23 and parathyroid hormone levels in response to a positive phosphate balance contribute to adverse clinical outcomes. These insights support the current practice of managing serum phosphate in patients with advanced chronic kidney disease, although definitive evidence of these effects is lacking. Given the potential toxicity of excess phosphate, the general population may also be viewed as a target for phosphate management. However, the widespread implementation of dietary phosphate intervention in the general population may not be warranted due to the limited impact of increased phosphate intake on mineral metabolism and clinical outcomes. Nonetheless, the increasing incidence of kidney disease or injury in our aging society emphasizes the potential importance of this issue. Further work is needed to more completely characterize phosphate toxicity and to establish the optimal therapeutic strategy for managing phosphate in patients with chronic kidney disease and in the general population. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

Recent solvent extraction experience at Savannah River

International Nuclear Information System (INIS)

Gray, L.W.; Burney, G.A.; Gray, J.H.; Hodges, M.E.; Holt, D.L.; Macafee, I.M.; Reif, D.J.; Shook, H.E.

1986-01-01

Tributyl phosphate-based solvent extraction processes have been used at Savannah River for more than 30 years to separate and purify thorium, uranium, neptunium, plutonium, americium, and curium isotopes. This report summarizes the advancement of solvent extraction technology at Savannah River during the 1980's. Topics that are discussed include equipment improvements, solvent treatment, waste reduction, and an improved understanding of the various chemistries in the process streams entering, within, and leaving the solvent extraction processes

The Preliminary Pollutant Limit Value Approach: Procedures and Data Base.

Science.gov (United States)

1984-06-01

and T is the temperature in OK. Soil Organic Carbon Adsorption Coefficient Koc ) 71. This is the ratio of the concentration of a compound physically...5 1 Table 10 includes some soil organic matter assays for different locales in the United States. 73. Soil adsorption isotherms are typically used to...0.003 Tributyl phosphate 0.01 - Trichlorometafos-3 0.4 S Triethanolamine 1.4 Phosbutyl 0.03 Phosphamide 0.03 Ph~halophos 0.2 Furfural 1.0 Chloranil

Status report: waste incineration and fixation for Waste Management, Production, and Reprocessing Division of the Department of Energy (July--December 1976)

International Nuclear Information System (INIS)

Ziegler, D.L.; White, J.W.; Johnson, A.J.; Fong, L.Q.; Teter, A.R.; Chung, S.F.

1977-01-01

Fluidized bed incineration and waste fixation processes are being used to process the types of wastes expected from nuclear fuel reprocessing and production plants. Test incineration runs have been made on two types of wastes: high efficiency particulate air (HEPA) filters and tributyl phosphate-solvent solutions. Laboratory-scale vitrification equipment was used to produce glass pellets from incinerator ash and blends of other expected waste streams. Computer modeling gave an expected product integrity life of over 2,000 years

Triphenyl phosphate allergy from spectacle frames

DEFF Research Database (Denmark)

Carlsen, L; Andersen, K E; Egsgaard, Helge

1986-01-01

A case of triphenyl phosphate allergy from spectacle frames is reported. Patch tests with analytical grade triphenyl phosphate, tri-m-cresyl phosphate, and tri-p-cresyl phosphate in the concentrations 5%, 0.5% and 0.05% pet. showed positive reactions to 0.05% triphenyl phosphate and 0.5% tri......-m-cresyl phosphate, but no reaction to tri-p-cresyl phosphate. Gas chromatography of the tricresyl phosphate 5% pet. patch test material supplied from Trolab showed that it contained a mixture of a wide range of triaryl phosphates, including 0.08% triphenyl phosphate which is above the threshold for detecting...

Studies on the treatment of organic wastes. Part 5

International Nuclear Information System (INIS)

Eschrich, H.; Humblet, L.; Geel, J. van.

1980-09-01

The Eurowatt process involves the quantitative extraction of tributyl phosphate (TBP), degradation products, and radionuclides from spent solvent mixtures by anhydrous phosphoric acid resulting in the recovery of a decontaminated diluent phase. The purified diluent can be reused or disposed of by burning. The radioactive TBP-phosphoric acid phase is heated to about 200 0 C to decompose the organic compounds to volatile hydrocarbons and non-volatile inorganic phosphoric acids. The inactive organic compounds are burned; the residual phosphoric acids, containing all the radionuclides, are conditioned for final storage by conversion into a phosphate glass or ceramic. Eurochemic's Eurowatt pilot installation is described and essential process data and results are given. (author)

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

Directory of Open Access Journals (Sweden)

Lílian Estrela Borges Baldotto

2014-06-01

Full Text Available Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i to select and characterize diazotrophs able to solubilize phosphates in vitro and (ii evaluate the initial performance of the pineapple cultivars Imperial and Pérola in response to inoculation with selected bacteria in combination with rock phosphate. The experiments were conducted at Universidade Estadual do Norte Fluminense Darcy Ribeiro, in 2009. In the treatments with bacteria the leaf contents of N, P and K were higher than those of the controls, followed by an increase in plant growth. These results indicate that the combined application of diazotrophic phosphate-solubilizing bacteria Burkholderia together with Araxá rock phosphate can be used to improve the initial performance of pineapple slips.

How do arbuscular mycorrhizal fungi handle phosphate? New insight into fine-tuning of phosphate metabolism.

Science.gov (United States)

Ezawa, Tatsuhiro; Saito, Katsuharu

2018-04-27

Contents Summary I. Introduction II. Foraging for phosphate III. Fine-tuning of phosphate homeostasis IV. The frontiers: phosphate translocation and export V. Conclusions and outlook Acknowledgements References SUMMARY: Arbuscular mycorrhizal fungi form symbiotic associations with most land plants and deliver mineral nutrients, in particular phosphate, to the host. Therefore, understanding the mechanisms of phosphate acquisition and delivery in the fungi is critical for full appreciation of the mutualism in this association. Here, we provide updates on physical, chemical, and biological strategies of the fungi for phosphate acquisition, including interactions with phosphate-solubilizing bacteria, and those on the regulatory mechanisms of phosphate homeostasis based on resurveys of published genome sequences and a transcriptome with reference to the latest findings in a model fungus. For the mechanisms underlying phosphate translocation and export to the host, which are major research frontiers in this field, not only recent advances but also testable hypotheses are proposed. Lastly, we briefly discuss applicability of the latest tools to gene silencing in the fungi, which will be breakthrough techniques for comprehensive understanding of the molecular basis of fungal phosphate metabolism. © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

Formulation of single super phosphate fertilizer from rock phosphate of Hazara, Pakistan

Directory of Open Access Journals (Sweden)

Matiullah Khan

2012-05-01

Full Text Available Phosphorus deficiency is wide spread in soils of Pakistan. It is imperative to explore the potential and economics of indigenous Hazara rock phosphate for preparation of single super phosphate fertilizer. For the subject study rock phosphate was collected from Hazara area ground at 160 mesh level with 26% total P2O5 content for manual preparation of single super phosphate fertilizer. The rock phosphate was treated with various concentrations of sulfuric acid (98.9%, diluted or pure in the field. The treatments comprised of 20 and 35% pure acid and diluted with acid-water ratios of 1:5, 1:2, 1:1 and 2:1 v/v for acidulation at the rate of 60 liters 100 kg-1 rock phosphate. The amount was prior calculated in the laboratory for complete wetting of rock phosphate. A quantity of 150 kg rock phosphate was taken as treatment. The respective amount of acid was applied with the spray pump of stainless steel or poured with bucket. After proper processing, chemical analysis of the products showed a range of available P2O5 content from 9.56 to 19.24% depending upon the amount of acid and its dilution. The results reveal at that 1:1 dilutions gave the highest P2O5 content (19.24%, lowest free acid (6 % and 32% weight increase. The application of acid beyond or below this combination either pure or diluted gave hygroscopic product and higher free acids. The cost incurred upon the manual processing was almost half the prevailing rates in the market. These results lead to conclude that application of sulfuric acid at the rate of 60 liters 100 kg-1 with the dilution of 50% (v/v can yield better kind of SSP from Hazara rock phosphate at lower prices.

Integrated assessment of the phosphate industry

International Nuclear Information System (INIS)

Ryan, M.T.; Cotter, S.J.

1980-05-01

The phosphate industry in the United States includes three major activities, namely, mining and milling of phosphate rock, phosphate product manufacture, and phosphate product use. Phosphatic materials contain uranium, thorium, and their decay products in greater than background amounts. This assessment of the radiological impacts associated with the redistribution of radioactive components of phosphate materials may provide insight into the effects of uranium extraction from phosphate materials for use in the nuclear fuel cycle

Role of Phosphate Transport System Component PstB1 in Phosphate Internalization by Nostoc punctiforme.

Science.gov (United States)

Hudek, L; Premachandra, D; Webster, W A J; Bräu, L

2016-11-01

In bacteria, limited phosphate availability promotes the synthesis of active uptake systems, such as the Pst phosphate transport system. To understand the mechanisms that facilitate phosphate accumulation in the cyanobacterium Nostoc punctiforme, phosphate transport systems were identified, revealing a redundancy of Pst phosphate uptake systems that exists across three distinct operons. Four separate PstB system components were identified. pstB1 was determined to be a suitable target for creating phenotypic mutations that could result in the accumulation of excessive levels of phosphate through its overexpression or in a reduction of the capacity to accumulate phosphate through its deletion. Using quantitative real-time PCR (qPCR), it was determined that pstB1 mRNA levels increased significantly over 64 h in cells cultured in 0 mM added phosphate and decreased significantly in cells exposed to high (12.8 mM) phosphate concentrations compared to the level in cells cultured under normal (0.8 mM) conditions. Possible compensation for the loss of PstB1 was observed when pstB2, pstB3, and pstB4 mRNA levels increased, particularly in cells starved of phosphate. The overexpression of pstB1 increased phosphate uptake by N. punctiforme and was shown to functionally complement the loss of PstB in E. coli PstB knockout (PstB - ) mutants. The knockout of pstB1 in N. punctiforme did not have a significant effect on cellular phosphate accumulation or growth for the most part, which is attributed to the compensation for the loss of PstB1 by alterations in the pstB2, pstB3, and pstB4 mRNA levels. This study provides novel in vivo evidence that PstB1 plays a functional role in phosphate uptake in N. punctiforme IMPORTANCE: Cyanobacteria have been evolving over 3.5 billion years and have become highly adept at growing under limiting nutrient levels. Phosphate is crucial for the survival and prosperity of all organisms. In bacteria, limited phosphate availability promotes the

Effects of education on low-phosphate diet and phosphate binder intake to control serum phosphate among maintenance hemodialysis patients: A randomized controlled trial

Directory of Open Access Journals (Sweden)

Eunsoo Lim

2018-03-01

Full Text Available Background : For phosphate control, patient education is essential due to the limited clearance of phosphate by dialysis. However, well-designed randomized controlled trials about dietary and phosphate binder education have been scarce. Methods : We enrolled maintenance hemodialysis patients and randomized them into an education group (n = 48 or a control group (n = 22. We assessed the patients' drug compliance and their knowledge about the phosphate binder using a questionnaire. Results : The primary goal was to increase the number of patients who reached a calcium-phosphorus product of lower than 55. In the education group, 36 (75.0% patients achieved the primary goal, as compared with 16 (72.7% in the control group (P = 0.430. The education increased the proportion of patients who properly took the phosphate binder (22.9% vs. 3.5%, P = 0.087, but not to statistical significance. Education did not affect the amount of dietary phosphate intake per body weight (education vs. control: -1.18 ± 3.54 vs. -0.88 ± 2.04 mg/kg, P = 0.851. However, the dietary phosphate-to-protein ratio tended to be lower in the education group (-0.64 ± 2.04 vs. 0.65 ± 3.55, P = 0.193. The education on phosphate restriction affected neither the Patient-Generated Subjective Global Assessment score (0.17 ± 4.58 vs. -0.86 ± 3.86, P = 0.363 nor the level of dietary protein intake (-0.03 ± 0.33 vs. -0.09 ± 0.18, P = 0.569. Conclusion : Education did not affect the calcium-phosphate product. Education on the proper timing of phosphate binder intake and the dietary phosphate-to-protein ratio showed marginal efficacy.

Zinc phosphate conversion coatings

Science.gov (United States)

Sugama, Toshifumi

1997-01-01

Zinc phosphate conversion coatings for producing metals which exhibit enhanced corrosion prevention characteristics are prepared by the addition of a transition-metal-compound promoter comprising a manganese, iron, cobalt, nickel, or copper compound and an electrolyte such as polyacrylic acid, polymethacrylic acid, polyitaconic acid and poly-L-glutamic acid to a phosphating solution. These coatings are further improved by the incorporation of Fe ions. Thermal treatment of zinc phosphate coatings to generate .alpha.-phase anhydrous zinc phosphate improves the corrosion prevention qualities of the resulting coated metal.

Thermodynamics of uranium and nitric acid extraction from aqueous solution of TBP/diluent

International Nuclear Information System (INIS)

Souza Freitas, R.F. de.

1982-06-01

A thermodynamically consistent procedure for predicting distribution equilibria for uranyl nitrate and nitric acid between an aqueous solution and 30 vol % tributyl phosphate (TBP) in a hydrocarbon diluent is studied. Experimental work is developed in order to obtain equilibrium data for the system uranyl nitrate, nitric acid, water and 30 vol % TBP in n-dodecane, at 25 0 C and 40 0 C. The theoretical equilibrium data, obtained with the aid of a computer, are compared with the experimental results. (Author) [pt

Bituminization of low- and medium-level radioactive wastes

International Nuclear Information System (INIS)

Lefillatre, G.

1976-01-01

French operations are presented concerning mainly: the bituminization of radioactive wastes produced in light water reactors; the direct bituminization of liquid effluents without concentration; the experiments carried out for 18 months on the land burial of concentrates solidified by bitumen into blocks of 100 liters. The knowledge acquired in France is exposed: in Valduc and in Saclay with facilities equipped with thin film evaporators and in Marcoule with the conditioning of trilaurylamine and tributyl-phosphate. At last the Cadarache bituminization [fr

Solvent degradation and cleanup: a survey and recent ORNL studies

International Nuclear Information System (INIS)

Mailen, J.C.; Tallent, O.K.

1984-01-01

This paper surveys the mechanisms for degradation of the tributyl phosphate and diluent components of Purex solvent by acid and radiation, reviews the problems encountered in plant operations resulting from the presence of these degradation products, and discusses methods for minimizing the formation of degradation products and accomplishing their removal. Scrubbing solutions containing sodium carbonate or hydroxylamine salts and secondary cleanup of solvents using solid sorbents are evaluated. Finally, recommendations for improved solvent cleanup are presented. 50 references, 4 figures, 3 tables

Hemodialysis for near-fatal sodium phosphate toxicity in a child receiving sodium phosphate enemas.

Science.gov (United States)

Becknell, Brian; Smoyer, William E; O'Brien, Nicole F

2014-11-01

This study aimed to demonstrate the importance of considering hemodialysis as a treatment option in the management of sodium phosphate toxicity. This is a case report of a 4-year-old who presented to the emergency department with shock, decreased mental status, seizures, and tetany due to sodium phosphate toxicity from sodium phosphate enemas. Traditional management of hyperphosphatemia with aggressive hydration and diuretics was insufficient to reverse the hemodynamic and neurological abnormalities in this child. This is the first report of the use of hemodialysis in a child without preexisting renal failure for the successful management of near-fatal sodium phosphate toxicity. Hemodialysis can safely be used as an adjunctive therapy in sodium phosphate toxicity to rapidly reduce serum phosphate levels and increase serum calcium levels in children not responding to conventional management.

Phosphate transporter mediated lipid accumulation in Saccharomyces cerevisiae under phosphate starvation conditions.

Science.gov (United States)

James, Antoni W; Nachiappan, Vasanthi

2014-01-01

In the current study, when phosphate transporters pho88 and pho86 were knocked out they resulted in significant accumulation (84% and 43%) of triacylglycerol (TAG) during phosphate starvation. However in the presence of phosphate, TAG accumulation was only around 45% in both pho88 and pho86 mutant cells. These observations were confirmed by radio-labeling, fluorescent microscope and RT-PCR studies. The TAG synthesizing genes encoding for acyltransferases namely LRO1 and DGA1 were up regulated. This is the first report for accumulation of TAG in pho88Δ and pho86Δ cells under phosphate starvation conditions. Copyright © 2013. Published by Elsevier Ltd.

21 CFR 137.175 - Phosphated flour.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Phosphated flour. 137.175 Section 137.175 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Related Products § 137.175 Phosphated flour. Phosphated flour, phosphated white flour, and phosphated...

Characterisation of aggregation of tributylphosphate molecules in organic solvent; Caracterisation de l'auto-organisation du phosphate de tributyle en solvant organique

Energy Technology Data Exchange (ETDEWEB)

Mandin, C.; Martinet, L.; Zemb, Th.; Berthon, L.; Madic, Ch

2000-07-01

This report presents a structural study of the aggregates formed with the organic phases of the extractant tri-n-butyl phosphate, used in the industrial PUREX process (Plutonium and Uranium Extraction; liquid-liquid solvent extraction) for the treatment of high radioactive waste. Combined Small Angle X-ray Scattering and Small Angle Neutron Scattering show that organic TBP solutions (in equilibrium with acid solutions) are organised in oligomeric aggregates. The influence of various parameters such as HNO{sub 3} or TBP concentrations, diluent or acid natures, does not seem to modify the aggregate shape and size, whereas the interactions are modified. Moreover the aggregates disappear under high temperatures, whereas the attractive interactions between them increase at low temperatures. The 'drop weight' method gives the critical micellar concentration values of TBP in case of H{sub 2}O or HNO{sub 3} extractions (H{sub 2}O: 0.48 M; HNO{sub 3} 2M: 0.65 M; at 21 deg C). Furthermore, the measures at different acid concentrations show that the c.m.c. varies with the acidity. The more acid the aqueous phase is, the smaller is the entropy in the system because of the numerous negative charges, i.e. the harder the micellization occurs, so the higher the c.m.c. value is. The sticky sphere model proposed by Baxter, can be used to model successfully small reverse micelles of the organic TBP phases. The aggregation number would be 4{+-}1 (water extraction) and 5{+-}1(HNO{sub 3}2M extraction). These values are also given by vapor pressure measurements. (authors)

Adsorbents for radioactive organic solvent wastes

International Nuclear Information System (INIS)

Ichinose, Shigeo; Kiribayashi, Takehiko.

1986-01-01

Purpose: To enable to settle radioactive solvents such as tributyl phosphate (TBP) and n-dodecane as they are without using hydrophobicizing agent such as quaternary ammonium salts. Constitution: The adsorbents are prepared by replacing interlaminer ions of swelling-type synthetic mica with alkaline earth metals or metal ions. For instance, synthetic micas introduced with Zr 4+ or Ca 2+ between the layers provide quite different functions from those of starting materials due to the properties of ions introduced between the layers. That is, they provide an intense affinity to organic phosphates such as TBP and transform into material showing a property of adsorbing and absorbing them. Particularly, the fixing nature to the phosphor content constituting TBP is significantly increased. (Horiuchi, T.)

Uranium/plutonium and uranium/neptunium separation by the Purex process using hydroxyurea

International Nuclear Information System (INIS)

Zhu Zhaowu; He Jianyu; Zhang Zefu; Zhang Yu; Zhu Jianmin; Zhen Weifang

2004-01-01

Hydroxyurea dissolved in nitric acid can strip plutonium and neptunium from tri-butyl phosphate efficiently and has little influence on the uranium distribution between the two phases. Simulating the 1B contactor of the Purex process by hydroxyurea with nitric acid solution as a stripping agent, the separation factors of uranium/plutonium and uranium/neptunium can reach values as high as 4.7 x 10 4 and 260, respectively. This indicates that hydroxyurea is a promising salt free agent for uranium/plutonium and uranium/neptunium separations. (author)

Explosion risks linked to red oils in the spent fuels reprocessing plants

International Nuclear Information System (INIS)

2008-06-01

This paper presents the risk of explosion associated with reactions between tributyl phosphate (TBP) and its degradation products and nitrates from nitric acid or associated with heavy metals (uranium and plutonium); These reactions may lead to the formation of unstable compounds known as 'red oils'. The feedback explosions linked to the formation of such compounds occurring in spent fuel reprocessing plants round the world, is briefly discussed. The main measures to control these risks, implemented in French factories concerned are also presented. (N.C.)

Radioactivity of phosphate ores from Karatas-Mazidag phosphate deposit of Turkey

International Nuclear Information System (INIS)

Akyuez, T.; Varinlioglu, A.; Kose, A.; Akyuez, S.

2000-01-01

The specific activities of 238 U, 226 Ra, 232 Th and 40 K in the composite samples of phosphate ores of type I (grey-coloured ore, with high P 2 O 5 (21-35%) and low calcite content) and of type II (grey coloured calcite ore, with low P 2 O 5 content (5-17%)) of Karatas-Mazidag phosphate deposit, Turkey, have been determined by gamma spectrometry together with phosphatic animal feed ingredients. The concentrations of 238 U, 226 Ra, 232 Th and 40 K were found to be up to 557, 625, 26 and 297 Bq x kg -1 , respectively. Radium equivalent activities of samples were calculated and compared with those given in the literature. Uranium concentration of the individual phosphate samples, from which composite samples of ores of type I and II have been prepared, were found to show and increasing trend with increasing P 2 O 5 and F concentrations. (author)

Phosphate application to firing range soils for Pb immobilization: The unclear role of phosphate

International Nuclear Information System (INIS)

Chrysochoou, Maria; Dermatas, Dimitris; Grubb, Dennis G.

2007-01-01

Phosphate treatment has emerged as a widely accepted approach to immobilize Pb in contaminated soils and waste media, relying on the formation of the highly insoluble mineral pyromorphite as solubility-controlling phase for Pb. As such, phosphate treatment has been proposed as a Best Management Practice (BMP) for firing ranges where Pb occurs in its metallic forms and several other phases (carbonates, oxides). While pyromorphite thermodynamically has the potential to control Pb solubility at low levels, its formation is kinetically controlled by pH, the solubility of the phosphate source, and the solubility of Pb species. Treatability studies have shown that excess quantities of soluble and acidic phosphate sources, such as phosphoric acid, are necessary for successful in situ treatment. Even under these conditions, Extended X-ray Absorption Fine Structure (EXAFS), the only reliable method to identify and quantify Pb speciation, showed that Pb conversion to pyromorphite in in situ treated soils was less than 45% after 32 months. Furthermore, the use of lime (CaO) to restore soil pH in acidified soil treatments inhibited further conversion. Additionally, phosphate treatment is known to reduce bioavailability through pyromorphite formation in the intestinal tract, and the phytoaccumulation of Pb; both desirable effects for Pb-impacted areas. Given the costs of phosphate treatment, the use of biogenic phosphate sources, such as bone meal, may be a more environmentally sustainable approach toward this end. In the many studies focusing on phosphate treatment, the attendant P leaching and eutrophication have been largely overlooked, along with other issues such as the enhanced leaching of oxyanionic contaminants, such as Se, As and W. The success and sustainability of applying phosphate as a BMP in firing range soils therefore remain questionable

Phosphate control in dialysis

Directory of Open Access Journals (Sweden)

Cupisti A

2013-10-01

Full Text Available Adamasco Cupisti,1 Maurizio Gallieni,2 Maria Antonietta Rizzo,2 Stefania Caria,3 Mario Meola,4 Piergiorgio Bolasco31Department of Clinical and Experimental Medicine, University of Pisa, Pisa, Italy; 2Nephrology and Dialysis Unit, San Carlo Borromeo Hospital, Milan, Italy; 3Territorial Department of Nephrology and Dialysis, ASL Cagliari, Italy; 4Sant'Anna School of Advanced Studies, University of Pisa, Pisa, ItalyAbstract: Prevention and correction of hyperphosphatemia is a major goal of chronic kidney disease–mineral and bone disorder (CKD–MBD management, achievable through avoidance of a positive phosphate balance. To this aim, optimal dialysis removal, careful use of phosphate binders, and dietary phosphate control are needed to optimize the control of phosphate balance in well-nourished patients on a standard three-times-a-week hemodialysis schedule. Using a mixed diffusive–convective hemodialysis tecniques, and increasing the number and/or the duration of dialysis tecniques are all measures able to enhance phosphorus (P mass removal through dialysis. However, dialytic removal does not equal the high P intake linked to the high dietary protein requirement of dialysis patients; hence, the use of intestinal P binders is mandatory to reduce P net intestinal absorption. Unfortunately, even a large dose of P binders is able to bind approximately 200–300 mg of P on a daily basis, so it is evident that their efficacy is limited in the case of an uncontrolled dietary P load. Hence, limitation of dietary P intake is needed to reach the goal of neutral phosphate balance in dialysis, coupled to an adequate protein intake. To this aim, patients should be informed and educated to avoid foods that are naturally rich in phosphate and also processed food with P-containing preservatives. In addition, patients should preferentially choose food with a low P-to-protein ratio. For example, patients could choose egg white or protein from a vegetable source

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

OpenAIRE

Lílian Estrela Borges Baldotto; Marihus Altoé Baldotto; Fábio Lopes Olivares; Adriane Nunes de Souza

2014-01-01

Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i) to select and characterize diazotrophs abl...

Separation process of zirconium and hafnium; Procede de separation du zirconium et du hafnium

Energy Technology Data Exchange (ETDEWEB)

Hure, J; Saint-James, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

About the separation different processes of zirconium-hafnium, the extraction by solvent in cross-current is the most easily the process usable on an industrial scale. It uses tributyl phosphate as solvent, diluted with white spirit to facilitate the decanting. Some exploratory tests showed that nitric environment seemed the most favorable for extraction; but a lot of other factors intervene in the separation process. We studied the influence of the acidity successively, the NO{sub 3}{sup -} ions concentration, the role of the cation coming with NO{sub 3}{sup -}, as well as the influence of the concentration of zirconium in the solution on the separation coefficient {beta} = {alpha}{sub Zr} / {alpha}{sub Hf}. (M.B.) [French] Des differents procedes de separation zirconium-hafnium, l'extraction par solvant en contre-courant est le procede le plus facilement utilisable a l'echelle industrielle. On utilise comme solvant le phosphate de tributyle, dilue avec du white spirit pour faciliter les decantations. Des essais preliminaires ont montre que le milieu nitrique semblait le plus favorable a l'extraction; mais beaucoup d'autres facteurs interviennent dans le processus de separation. Nous avons etudie successivement l'influence de l'acidite, celle de la concentration en ions NO{sub 3}{sup -}, le role du cation accompagnant NO{sub 3}{sup -}, ainsi que l'influence de la concentration en zirconium de la solution sur le coefficient de separation {beta} = {alpha}{sub Zr} / {alpha}{sub Hf}. (MB)

Uranium-phosphate relationship in phosphated chalks of the Mons and Picardie Bassins

Energy Technology Data Exchange (ETDEWEB)

Quinif, Y; Charlet, J M; Dupuis, C; Robaszynski, F [Faculte Polytechnique de Mons (Belgium)

1981-11-30

The lithological and geochemical conditions relative to the ''Senonian'' phosphatic chalks are relatively simple in the Basins of Mons (Belgium) and of Picardy (France). Their characteristics permit us to study chiefly the uranium-phosphate relation. It appears a very good linear correlation between the phosphate and the uranium. The coefficient U/P/sub 2/O/sub 5/ remains a constant from the bottom to the top of the same section, but changes in space for synchronic formations (lateral variation of geochemical facies) and in time for two separated basins.

Uranium abundance in some sudanese phosphate ores

International Nuclear Information System (INIS)

Adam, A.A.; Eltayeb, M.A.H.

2009-01-01

This work was carried out mainly to analysis of some Sudanese phosphate ores, for their uranium abundance and total phosphorus content measured as P 2 O 5 %. For this purpose, 30 samples of two types of phosphate ore from Eastern Nuba Mountains, in Sudan namely, Kurun and Uro areas were examined. In addition, the relationship between uranium and major, and trace elements were obtained, also, the natural radioactivity of the phosphate samples was measured, in order to characterize and differentiate between the two types of phosphate ores. The uranium abundance in Uro phosphate with 20.3% P 2 O 5 is five time higher than in Kurun phosphate with 26.7% P 2 O 5 . The average of uranium content was found to be 56.6 and 310 mg/kg for Kurun and Uro phosphate ore, respectively. The main elements in Kurun and Uro phosphate ore are silicon, aluminum, and phosphorus, while the most abundant trace elements in these two ores are titanium, strontium and barium. Pearson correlation coefficient revealed that uranium in Kurun phosphate shows strong positive correlation with P 2 O 5 , and its distribution is essentially controlled by the variations of P2O5 concentration, whereas uranium in Uro phosphate shows strong positive correlation with strontium, and its distribution is controlled by the variations of Sr concentration. Uranium behaves in different ways in Kurun phosphate and in Uro phosphate. Uro phosphate shows higher concentrations of all the estimated radionuclides than Kurun phosphate. According to the obtained results, it can be concluded that Uro phosphate is consider as secondary uranium source, and is more suitable for uranium recovery, because it has high uranium abundance and low P 2 O 5 %, than Kurun phosphate. (authors) [es

Uranium from phosphate ores

International Nuclear Information System (INIS)

Hurst, F.J.

1983-01-01

The following topics are described briefly: the way phosphate fertilizers are made; how uranium is recovered in the phosphate industry; and how to detect covert uranium recovery operations in a phsophate plant

Electrochemical Reduction of Zinc Phosphate

International Nuclear Information System (INIS)

Kim, Chang Hwan; Lee, Jung Hyun; Shin, Woon Sup

2010-01-01

We demonstrated first that the electrochemical reduction of zinc phosphate in neutral phosphate buffer is possible and potentially applicable to bio-compatible rechargeable battery. The actual redox component is Zn(s)/Zn phosphate(s) and the future research about the control of crystal formation for the better cyclability is required. In lead-acid battery, the electrochemical redox reaction of Pb (s) /PbSO 4(s) is used by reducing Pb(II) and oxidizing Pb(0) in sulfate rich solution. Since both reduced form and oxidized form are insoluble, they cannot diffuse to the opposite electrodes and react. It is a very common strategy to make a stable battery electrode that a metal element is reduced and oxidized in solution containing an abundance of anion readily precipitating with the metal ion. For the application of this strategy to construction of rechargeable battery using bio-compatible electrode materials and electrolytes, the use of phosphate ion can be considered as anion readily precipitating with metal ions. If phosphate buffer with neutral pH is used as electrolyte, the better bio-compatibility will be achieved than most of rechargeable battery using strong acid, strong base or organic solvent as electrolyte solution. There are many metal ions readily precipitating with phos-phate ion, and zinc is one of them

Radiological impact of natural radioactivity in Egyptian phosphate rocks, phosphogypsum and phosphate fertilizers

International Nuclear Information System (INIS)

El-Bahi, S.M.; Sroor, A.; Mohamed, Gehan Y.; El-Gendy, N.S.

2017-01-01

In this study, the activity concentrations of the natural radionuclides in phosphate rocks and its products were measured using a high- purity germanium detector (HPGe). The obtained activity results show remarkable wide variation in the radioactive contents for the different phosphate samples. The average activity concentration of "2"3"5U, "2"3"8U, "2"2"6Ra, "2"3"2Th and "4"0K was found as (45, 1031, 786, 85 and 765 Bq/kg) for phosphate rocks, (28, 1234, 457, 123 and 819 Bq/kg) for phosphate fertilizers, (47, 663, 550, 79 and 870 Bq/kg) for phosphogypsum and (25, 543, 409, 54 and 897 Bq/kg) for single super phosphate respectively. Based on the measured activities, the radiological parameters (activity concentration index, absorbed gamma dose rate in outdoor and indoor and the corresponding annual effective dose rates and total excess lifetime cancer risk) were estimated to assess the radiological hazards. The total excess lifetime cancer risk (ELCR) has been calculated and found to be high in all samples, which related to high radioactivity, representing radiological risk for the health of the population. - Highlights: • Level of radioactivity of phosphate rocks and by-products samples. • The radiological health hazard parameters. • Radiological risk to the health of the population. • The excess lifetime cancer risk factor.

Interphase transfer kinetics of uranium using the drop method, Lewis cell, and Kenics mixer

International Nuclear Information System (INIS)

Horner, D.E.; Mailen, J.C.; Thiel, S.W.; Scott, T.C.; Yates, R.G.

1979-05-01

The rate constants for the interphase transfer of uranium between 3.5 M HNO 3 and tributyl phosphate (TBP) - normal hydrocarbon diluent solutions have been measured using the single drop method, Lewis cell method, and a Kenics mixer - centrifugal separator. Rate constants obtained by all methods were the same within experimental error. The variables studied that affect the rate constants include the TBP concentration, the acidity and total neutral nitrate concentrations of the aqueous phase, and temperature. Results of these tests indicate that the rate controlling mechanism is chemical reaction at the interface

Study of metabolism of hydrazoic acid in the purex process

International Nuclear Information System (INIS)

Violet, A.

1988-03-01

The transfer of HN 3 between different phases has been studied - It has been found that the transfer of HN 3 from aqueous solution of the reprocessing to gaz phase is a physical mechanism of desorbtion. - The limiting phenomena of the transfer of HN 3 fromt the organic to the gaseous phase, is the decomplexation of this specy with tributyl phosphate (TBP). - Chemical reactions of hydrazoic acid occurring with nitrogen oxides in the gaseous flow has shown that it is rapidly destroyed in the presence of nitrogen dioxide [fr

Solvent extraction of thorium from nitrate medium by TBP, Cyanex272 and their mixture

International Nuclear Information System (INIS)

Mostaan Shaeri; Ahmad Rahbar Kelishami; Meisam Torab-Mostaedi

2015-01-01

The extraction behavior of thorium(IV) has been investigated with tri-butyl phosphate (TBP) and bis(2,4,4-trimethylpentyl) phosphinic acid (Cyanex272) in kerosene from nitrate medium. The effect of operating variables including time, aqueous phase acidity (pH), extractant concentration and temperature were investigated. This study also examined the synergistic enhancement of the extraction of thorium(IV) from nitrate medium by mixtures of TBP and Cyanex272 for the first time. The optimum synergistic enhancement factor of 3.86 was obtained at a Cyanex272/TBP molar ratio of 1:4. (author)

Evaluation of lyophility of carbon materials for electrodes of supercapacitors

Science.gov (United States)

Kompan, M. E.; Agafonov, D. V.; Bursian, A. E.; Dmitriev, D. S.; Mikryukova, M. A.

2016-12-01

The heats of wetting have been measured experimentally for some of the solvents used for the preparation of electrolytes of supercapacitors. For the first time, the heat of wetting has been measured for a new promising solvent—tributyl phosphate. Using acetonitrile as an example, the possible orientation of the molecule at the adsorbing surface has been investigated by the technique of surface-enhanced Raman scattering (SERS) (effect of giant enhancement of the scattering by a conducting surface). The calculated estimates have been obtained for the quantities found in the experiment.

Investigation into kinetics of redox interaction in the system Ce(4) β-diketonate-additional ligand

International Nuclear Information System (INIS)

Anufrieva, S.I.; Snezhko, N.I.; Pechurova, N.I.; Martynenko, L.N.; Spitsyn, V.I.

1981-01-01

The rate of reduction of β-diketonate complexes of Ce(4) to Ce(3) β-diketonates in benzene solution in the presence and in the absence of additional ligands is studied using spectrophotometry. The rate of reduction of Ce(4) β-diketonates increases in the series Ce(TTFA) 4 4 4 4 4 (TTFA - thenoyltrifluoroacetone, DPM- --dipivaloylmethane, DBM - dibenzoylemethane, BA benzoylacetone, AA - acetylaceton). The studied phosphorus-containing additional ligands as to their effect on the rate of Ce (4) reduction can be arranged in the following order: trioctylphosphine oxide>triphenylphosphine oxide>tributyl phosphate [ru

Recent technical progress in the French uranium industry

International Nuclear Information System (INIS)

Huet, H.

1961-01-01

This paper reviews the present-day uranium production situation in France. The various stages of the treatment the concentrates receive, leading to the final production of the metal, are described briefly: dissolution, purification by extraction with a mixture of tributyl phosphate and white spirit, precipitation with ammonia, drying and calcination of the trioxide, reduction with hydrogen, cracked ammonia or preferably pure ammonia gas, fluorination with anhydrous hydrofluoric acid, and production of the metal by the calcium thermite process. Recent work of an original nature is discussed in greater detail. (author) [fr

Synergistic solvent extraction of Eu(III) and Tb(III) with mixtures of various organophosphorus extractants

International Nuclear Information System (INIS)

Reddy, B.V.; Reddy, L.K.; Reddy, A.S.

1994-01-01

Synergistic solvent extraction of Eu(III) and Tb(III) from thiocyanate solutions with mixtures of 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHPNA) and di-2-ethylhexylphosphoric acid (DEHPA) or tributyl phosphate (TBP) or trioctylphosphine oxide (TOPO) or triphenylphosphine oxide (TPhPO) in benzene has been studied. The mechanism of extraction can be explained by a simple chemically based model. The equilibrium constants of the mixed-ligand species of the various neutral donors have been determined by non-linear regression analysis. (author) 13 refs.; 9 figs.; 2 tabs

Application of salting-out effect equation to modelling of liquid-liquid distribution systems

International Nuclear Information System (INIS)

Pitsch, H.K.

1986-03-01

Physicochemical interpretation of salting-out is reviewed and effects of the medium on liquid-liquid distribution equilibria are described by two non-specific parameters of salting-out agents: total concentration of species in the aqueous phase and water activity. Thus extraction of a given constituent in various media can be forecasted with few data. Different uranyl and technetium (VII) extraction systems are analyzed to show the potentiality of the method. Coextraction of nitric acid and uranyl nitrate by tributyl phosphate is used to show the possibility of modelling complex distribution systems in industrial conditions [fr

Effects of infrared lasers on chemical extraction reactions in liquid-liquid systems

International Nuclear Information System (INIS)

Baoyu, X.

A study was made of the effects of infrared lasers on equilibrium distributions of uranyl ions between aqueous solution phases containing nitric acid or hydrochloric acid and organic solvent phases of tributyl phosphate (TBP). The experimental results indicated that uranium concentrations in the organic solvent phase increased under TEA CO 2 laser irradiation up to a maximum of 44% as compared to cases in which laser radiation was not applied. The possibility that this type of laser extraction effect might be applied to separation of uranium isotopes was also discussed

Calcium phosphates: what is the evidence?

Science.gov (United States)

Larsson, Sune

2010-03-01

A number of different calcium phosphate compounds such as calcium phosphate cements and solid beta-tricalcium phosphate products have been introduced during the last decade. The chemical composition mimics the mineral phase of bone and as a result of this likeness, the materials seem to be remodeled as for normal bone through a cell-mediated process that involves osteoclastic activity. This is a major difference when compared with, for instance, calcium sulphate compounds that after implantation dissolve irrespective of the new bone formation rate. Calcium phosphates are highly biocompatible and in addition, they act as synthetic osteoconductive scaffolds after implantation in bone. When placed adjacent to bone, osteoid is formed directly on the surface of the calcium phosphate with no soft tissue interposed. Remodeling is slow and incomplete, but by adding more and larger pores, like in ultraporous beta-tricalcium phosphate, complete or nearly complete resorption can be achieved. The indications explored so far include filling of metaphyseal fracture voids or bone cysts, a volume expander in conjunction with inductive products, and as a carrier for various growth factors and antibiotics. Calcium phosphate compounds such as calcium phosphate cement and beta-tricalcium phosphate will most certainly be part of the future armamentarium when dealing with fracture treatment. It is reasonable to believe that we have so far only seen the beginning when it comes to clinical applications.

Steel corrosion in tributyl phosphate in the presence of water and ethyl mercaptan

International Nuclear Information System (INIS)

Pischik, L.M.; Tsinman, A.I.

1979-01-01

Studied is the corrosion of steels St3, 15Kh5M, 08Kh13, 10Kh14G14N4T, 08Kh18G8N2T, 10Kh17N13M2T in TBP, in mixtures of TBP with ethyl mercaptan (EM) and two-phase systems TBP-water and TBP-water-EM at 50-150 deg. In pure TBP St3 corrosion rate is low even at 150 deg. In the presence of water St 3 strongly corrodes at above 50 deg temperature in organic and water layers and also in gas phase. The steel-08Kh18G8N2T at 90 deg in acid TBP is passive and its corrosion rate is lower than 0.01 mm/year. In identical conditions the resistance of stainless steels increases together with chromium content but in TBP with acid number 100 and above at 150 deg all tested steels including steel-10Kh17N13M2T are slightly resistant. Thus, even in absence of corrosion active additions of EM the mixture of TBP-water at higher temperature is agressive in relation not only to carbon steel but also to stainless steels

Determination of tributyl phosphate (TBP) by precision densimetry : TBP-varsol-HNO3 system

International Nuclear Information System (INIS)

Matsuda, H.T.; Araujo, B.F. de; Araujo, J.A. de

1980-01-01

A simple and rapid method for TBP direct determination is presented, based on precision densimetry, aiming to control solvent concentration in the TBP-Varsol system during the reprocessing of irradiated uranium. The method comprises the determination of the density of liquids or gases by electronic measurement of the variation in the frequency (f) or period (T = 1/f) of a glass oscillator containing the liquid or the gas. (C.L.B.) [pt

Phosphate additives in food--a health risk.

Science.gov (United States)

Ritz, Eberhard; Hahn, Kai; Ketteler, Markus; Kuhlmann, Martin K; Mann, Johannes

2012-01-01

Hyperphosphatemia has been identified in the past decade as a strong predictor of mortality in advanced chronic kidney disease (CKD). For example, a study of patients in stage CKD 5 (with an annual mortality of about 20%) revealed that 12% of all deaths in this group were attributable to an elevated serum phosphate concentration. Recently, a high-normal serum phosphate concentration has also been found to be an independent predictor of cardiovascular events and mortality in the general population. Therefore, phosphate additives in food are a matter of concern, and their potential impact on health may well have been underappreciated. We reviewed pertinent literature retrieved by a selective search of the PubMed and EU databases (www.zusatzstoffe-online.de, www.codexalimentarius.de), with the search terms "phosphate additives" and "hyperphosphatemia." There is no need to lower the content of natural phosphate, i.e. organic esters, in food, because this type of phosphate is incompletely absorbed; restricting its intake might even lead to protein malnutrition. On the other hand, inorganic phosphate in food additives is effectively absorbed and can measurably elevate the serum phosphate concentration in patients with advanced CKD. Foods with added phosphate tend to be eaten by persons at the lower end of the socioeconomic scale, who consume more processed and "fast" food. The main pathophysiological effect of phosphate is vascular damage, e.g. endothelial dysfunction and vascular calcification. Aside from the quality of phosphate in the diet (which also requires attention), the quantity of phosphate consumed by patients with advanced renal failure should not exceed 1000 mg per day, according to the guidelines. Prospective controlled trials are currently unavailable. In view of the high prevalence of CKD and the potential harm caused by phosphate additives to food, the public should be informed that added phosphate is damaging to health. Furthermore, calls for labeling

Phosphate analysis of natural sausage casings preserved in brines with phosphate additives as inactivating agent - Method validation.

Science.gov (United States)

Wijnker, J J; Tjeerdsma-van Bokhoven, J L M; Veldhuizen, E J A

2009-01-01

Certain phosphates have been identified as suitable additives for the improvement of the microbial and mechanical properties of processed natural sausage casings. When mixed with NaCl (sodium chloride) and used under specific treatment and storage conditions, these phosphates are found to prevent the spread of foot-and-mouth disease and classical swine fever via treated casings. The commercially available Quantichrom™ phosphate assay kit has been evaluated as to whether it can serve as a reliable and low-tech method for routine analysis of casings treated with phosphate. The outcome of this study indicates that this particular assay kit has sufficient sensitivity to qualitatively determine the presence of phosphate in treated casings without interference of naturally occurring phosphate in salt used for brines in which casings are preserved.

Characterization of a calcium phosphate cement based on alpha-tricalcium phosphate obtained by wet precipitation process

International Nuclear Information System (INIS)

Thurmer, M.B.; Diehl, C.E.; Vieira, R.S.; Coelho, W.T.G.; Santos, L.A.

2012-01-01

There are several systems of calcium phosphate cements being studied. Those based on alpha-tricalcium phosphate are of particular interest. After setting they produce calcium deficient hydroxyapatite similar to bone like hydroxyapatite. This work aims to obtain alpha-tricalcium phosphate powders by the wet precipitation process, using calcium nitrate and phosphoric acid as reagents. This powder was characterized by infrared spectroscopy, X-ray diffraction and particle size distribution. In order to prepare the calcium phosphate cement, the powder was mixed with an accelerator in an aqueous solution. The mechanical properties of the cement were assessed and it was evaluated by means of apparent density, X-ray diffraction and scanning electron microscopy. The described method produced crystalline alpha-tricalcium phosphate as the major phase. The calcium phosphate cement showed high values of compression strength (50 MPa). The soaking of the cement in a simulated body fluid (SBF) formed a layer of hydroxyapatite like crystals in the surface of the samples. (author)

Phosphate solubilization and multiple plant growth promoting ...

African Journals Online (AJOL)

Phosphate solubilizing efficiencies of the strains were analyzed using different insoluble phosphorus sources and the results show that most isolates released a substantial amount of soluble phosphate from tricalcium phosphate, rock phosphate and bone meal. Screening for multiple plant growth promoting attributes ...

Evaluation of intestinal phosphate binding to improve the safety profile of oral sodium phosphate bowel cleansing.

Directory of Open Access Journals (Sweden)

Stef Robijn

Full Text Available Prior to colonoscopy, bowel cleansing is performed for which frequently oral sodium phosphate (OSP is used. OSP results in significant hyperphosphatemia and cases of acute kidney injury (AKI referred to as acute phosphate nephropathy (APN; characterized by nephrocalcinosis are reported after OSP use, which led to a US-FDA warning. To improve the safety profile of OSP, it was evaluated whether the side-effects of OSP could be prevented with intestinal phosphate binders. Hereto a Wistar rat model of APN was developed. OSP administration (2 times 1.2 g phosphate by gavage with a 12h time interval induced bowel cleansing (severe diarrhea and significant hyperphosphatemia (21.79 ± 5.07 mg/dl 6h after the second OSP dose versus 8.44 ± 0.97 mg/dl at baseline. Concomitantly, serum PTH levels increased fivefold and FGF-23 levels showed a threefold increase, while serum calcium levels significantly decreased from 11.29 ± 0.53 mg/dl at baseline to 8.68 ± 0.79 mg/dl after OSP. OSP administration induced weaker NaPi-2a staining along the apical proximal tubular membrane. APN was induced: serum creatinine increased (1.5 times baseline and nephrocalcinosis developed (increased renal calcium and phosphate content and calcium phosphate deposits on Von Kossa stained kidney sections. Intestinal phosphate binding (lanthanum carbonate or aluminum hydroxide was not able to attenuate the OSP induced side-effects. In conclusion, a clinically relevant rat model of APN was developed. Animals showed increased serum phosphate levels similar to those reported in humans and developed APN. No evidence was found for an improved safety profile of OSP by using intestinal phosphate binders.

Development of plasticised nano-biocomposites of poly(hydroxybutyrate-co-hydroxyvalerate)/montmorillonite organically modified (PHBV/OMMT); Desenvolvimento de nanobiocompositos plastificados de poli(hidroxibutirato-co-hidroxivalerato)/montimorilonita organomodificada (PHBV/OMMT)

Energy Technology Data Exchange (ETDEWEB)

Correa, M.C., E-mail: nascente@ufscar.b [Universidade Federal de Sao Carlos (PPGCEM/UFSCAR), SP (Brazil). Pos-graduacao em Ciencia e Engenharia de Materiais; Pollet, E.; Averous, L. [Ecole Europeenne de Chimie, Polymeres et Materiaux (LIPHT/ECPM), Strasbourg (France). Lab. d' Ingenierie des Polymeres pour les Hautes Technologies; Agnell, J.A.M.; Nascente, P.A.P. [Universidade Federal de Sao Carlos (DEMA/UFSCAR), SP (Brazil). Dept. de Engenharia de Materiais

2010-07-01

Several studies have aimed to improve the properties of biopolymers by the incorporation of nano-sized fillers, such as organo-modified montmorillonite (OMMT), to form nano-biocomposites. The objective of this work is to investigate the influence of acetyl tributyl citrate (ATBC) plasticizer with PHBV/OMMT nano-biocomposites aiming at improving their behavior. The materials PHBV, OMMT (C30B), and ATBC were provided by PHB Industrial S/A (Brazil), Southern Clay Products (USA), and Scandiflex S/A (Brazil), respectively. In this study the processing parameters and the formulations were controlled, pursuing materials with good mechanical and barrier properties with high biodegradability and with greater ease of processing. The analysis of the results obtained by TGA, GPC, WAXS, DSC, mechanical properties, and biodegradability lead to the conclusion that the addition of plasticizer in nanobiocomposites improved processability and did not influence the state of nano-sized load dispersion. It can be concluded that the addition of plasticizer is a good alternative to the processability of nanocomposites of PHAs. (author)

Phosphate and phosphate fertilizer sector: structure and future prospects. [Uranium recovery

Energy Technology Data Exchange (ETDEWEB)

Zenaidi, B

1981-12-01

A statement of the past evolution of this sector's structure is given. Various prospective studies which have been made are reviewed and lead to the precision of the phosphate requirement in the year 2000 which is between 200 and 250 Mt. Only a small section p. 696-697 is devoted to recovery of uranium contained in phosphate and prospects in this field are given.

Better prospects for phosphate production

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

The extraction of uranium as a by product of phosphate production is discussed. Techniques being commercially developed are described. The trend towards the wet process, in which sulphuric acid is used to dissolve the phosphate, producing phosphoric acid, is also the preferred method for uranium recovery. Recovery from a wet process phosphoric acid stream, integrated with phosphate fertilizer manufacture, is becoming increasingly commercially viable for the production of yellow-cake.

The Oxygen Isotopic Composition of Phosphate: A Tracer for Phosphate Sources and Cycling

Energy Technology Data Exchange (ETDEWEB)

Mclaughlin, K. [Southern California Coastal Water Research Project, Costa Mesa, University of California, CA (United States); Young, M. B.; Paytan, A.; Kendall, C. [U.S. Geological Survey, University of California, CA (United States)

2013-05-15

Phosphorus (P) is a limiting macro-nutrient for primary productivity and anthropogenic P-loading to aquatic ecosystems is one of the leading causes of eutrophication in many ecosystems throughout the world. Because P has only one stable isotope, traditional isotope techniques are not possible for tracing sources and cycling of P in aquatic systems. However, much of the P in nature is bonded to four oxygen (O) atoms as orthophosphate (PO{sub 4}{sup 3-}). The P-O bonds in orthophosphate are strongly resistant to inorganic hydrolysis and do not exchange oxygen with water without biological mediation (enzyme-mediated recycling). Thus, the oxygen isotopic composition of dissolved inorganic phosphate ({delta}{sup 18}O{sub p}) may be used as a tracer for phosphate sources and cycling in aquatic ecosystems. Recently, several studies have been conducted utilizing {delta}{sup 18}O{sub p} as a tracer for phosphate sources and cycling in various aquatic environments. Specifically, work to date indicates that {delta}{sup 18}O{sub p} is useful for determining sources of phosphate to aquatic systems if these sources have unique isotopic signatures and phosphate cycling within the system is limited compared to input fluxes. In addition, because various processes imprint specific fractionation effects, the {delta}{sup 18}O{sub p} tracer can be utilized to determine the degree of phosphorous cycling and processing through the biomass. This chapter reviews several of these studies and discusses the potential to utilize the {delta}{sup 18}O{sub p} of phosphate in rivers and streams. (author)

Occurrence and functioning of phosphate solubilizing ...

African Journals Online (AJOL)

Occurrence and functioning of phosphate solubilizing microorganisms from oil palm tree ( Elaeis guineensis ) rhizosphere in Cameroon. ... While the use of soluble mineral phosphate fertilizers is the obvious best means to combat phosphate ... in order to improve agricultural production, using low inputs technology. Isolates ...

PHOSPHATE CRYSTALLURIA IN VARIOUS FORMS OF UROLITHIASIS AND POSSIBILITIES OF ITS PROGNOSTICATION IN PATIENTS WITH PHOSPHATE STONES

Directory of Open Access Journals (Sweden)

O. V. Konstantinova

2017-01-01

Full Text Available Purpose. Definition of types of crystalluria in various forms of urolithiasis and biochemical signs of phosphate crystals in the urine, while phosphate urolithiasis (infectious origin.Patients and methods. The study involved 144 patients with recurrent urolithiasis — 75 women and 69 men. Of these, 46 — diagnosed calculi with uric acid, 44 — calcium oxalate or mixed with a prevalence of calcium oxalate, in 54 — phosphate rocks (carbonate-apatite and/or struvite. The age of patients ranged from 21 to 74 years. 93 people have been under long-term, within 2–15 years, outpatient observation. The examination included the collection of anamnesis, general and microbiological analysis of urine, biochemical blood serum and urine on 10 indicators, reflecting renal function, state of the protein, water and electrolyte metabolism, uric acid metabolism, the chemical composition of the stone analysis.Results. It was found that in patients with calcium oxalate stones phosphaturia has been diagnosed in 2% of cases. And, along with calcium phosphate crystals they had oxalate crystals. In patients with phosphate urolithiasis phosphaturia observed in 96% of patients, in two patients (4% they determined except phosphates also oxalate salt in urine sediment. Patients with phosphate urolithiasis at occurrence of phosphate crystalluria have metabolic state changes: increased serum uric acid concentration from 0.322 ± 0.009 to 0.367 ± 0.018 mmol/l daily renal excretion of inorganic phosphate 23.94 ± 2.93 mmol/day to 32.12 ± 4.39 mmol/day, and reduced total calcium content in urine 6.61 ± 0.94 mmol/day to 3.37 ± 0.89 mmol/day. The results led to the following conclusion.Conclusion. Biochemical signs of occurrence of phosphate crystalluria in patients with stones of infectious origin can be: the approaching level of excretion in the urine of inorganic phosphates to 32,12 ± 4,39 mmol/day, serum uric acid concentration to 0,367 ± 0,018 mmol/l, and the

on association of trialkyl phosphates

International Nuclear Information System (INIS)

Petkovic, D.M.; Maksimovic, Z.B.

1976-01-01

The association constants of tri-n-butyl (TBP), tri-n-propyl (TPP) and triethyl phosphate (TEP) with chloroform, carbon tetrachloride and benzene were determined by dielectric constant, proton magnetic resonance and vapor pressure measurements. Correlation of the trialkyl phosphate-chloroform association constants, using the Hammett equation, showed their increase with the number of carbon atoms in the aliphatic radicals. The change of trialkyl phosphate reactivity with temperature was used to determine the thermodynamic quantities. (author)

Bio-treatment of phosphate from synthetic wastewater using ...

African Journals Online (AJOL)

In this study, the efficient phosphate utilizing isolates were used to remove phosphate from synthetic phosphate wastewater was tested using batch scale process. Hence the objective of the present study was to examine the efficiency of bacterial species individually for the removal of phosphate from synthetic phosphate ...

Infrared-spectroscopy analysis of zinc phosphate and nickel and manganese modified zinc phosphate coatings on electrogalvanized steel

International Nuclear Information System (INIS)

Fernandes, Kirlene Salgado; Alvarenga, Evandro de Azevedo; Lins, Vanessa de Freitas Cunha

2011-01-01

Hopeite-type phosphate coatings in which zinc is partially replaced by other metals like manganese and nickel are of great interest for the automotive and home appliance industries. Such industries use phosphate conversion coatings on galvanized steels in association with cataphoretic electro painting. Zinc phosphates modified with manganese and nickel are isomorphic with the hopeite, and the phase identification using X-ray diffraction is difficult. In this paper, the phosphate coatings are identified using the Fourier transform infrared spectroscopy (FTIR). (author)

Application of Calcium Phosphate Materials in Dentistry

Directory of Open Access Journals (Sweden)

Jabr S. Al-Sanabani

2013-01-01

Full Text Available Calcium phosphate materials are similar to bone in composition and in having bioactive and osteoconductive properties. Calcium phosphate materials in different forms, as cements, composites, and coatings, are used in many medical and dental applications. This paper reviews the applications of these materials in dentistry. It presents a brief history, dental applications, and methods for improving their mechanical properties. Notable research is highlighted regarding (1 application of calcium phosphate into various fields in dentistry; (2 improving mechanical properties of calcium phosphate; (3 biomimetic process and functionally graded materials. This paper deals with most common types of the calcium phosphate materials such as hydroxyapatite and tricalcium phosphate which are currently used in dental and medical fields.

Phosphate acquisition efficiency and phosphate starvation tolerance ...

Indian Academy of Sciences (India)

3Department of Genetics and Plant Breeding, College of Agriculture, Lembucherra, Tripura 799 ... vated in soil like red and lateritic or acid, with low soluble phosphate content. ..... activation of genes involved in the adaptation of Arabidopsis to.

Most consumed processed foods by patients on hemodialysis: Alert for phosphate-containing additives and the phosphate-to-protein ratio.

Science.gov (United States)

Watanabe, Marcela T; Araujo, Raphael M; Vogt, Barbara P; Barretti, Pasqual; Caramori, Jacqueline C T

2016-08-01

Hyperphosphatemia is common in patients with chronic kidney disease (CKD) stages IV and V because of decreased phosphorus excretion. Phosphatemia is closely related to dietary intake. Thus, a better understanding of sources of dietary phosphate consumption, absorption and restriction, particularly inorganic phosphate found in food additives, is key to prevent consequences of this complication. Our aims were to investigate the most commonly consumed processed foods by patients with CKD on hemodialysis, to analyze phosphate and protein content of these foods using chemical analysis and to compare these processed foods with fresh foods. We performed a cross-sectional descriptive analytical study using food frequency questionnaires to rank the most consumed industrialized foods and beverages. Total phosphate content was determined by metavanadate colorimetry, and nitrogen content was determined by the Kjeldahl method. Protein amounts were estimated from nitrogen content. The phosphate-to-protein ratio (mg/g) was then calculated. Processed meat protein and phosphate content were compared with the nutritional composition of fresh foods using the Brazilian Food Composition Table. Phosphate measurement results were compared with data from the Food Composition Table - Support for Nutritional Decisions. An α level of 5% was considered significant. Food frequency questionnaires were performed on 100 patients (mean age, 59 ± 14 years; 57% male). Phosphate additives were mentioned on 70% of the product labels analyzed. Proteins with phosphate-containing additives provided approximately twice as much phosphate per gram of protein compared with that of fresh foods (p processed foods are higher than those of fresh foods, as well as phosphate-to-protein ratio. A better understanding of phosphate content in foods, particularly processed foods, may contribute to better control of phosphatemia in patients with CKD. Copyright © 2016 European Society for Clinical Nutrition and

31P-Nuclear Magnetic Resonance Determination of Phosphate Compartmentation in Leaves of Reproductive Soybeans (Glycine max L.) as Affected by Phosphate Nutrition 1

Science.gov (United States)

Lauer, Michael J.; Blevins, Dale G.; Sierzputowska-Gracz, Hanna

1989-01-01

Most leaf phosphorus is remobilized to the seed during reproductive development in soybean. We determined, using 31P-NMR, the effect phosphorus remobilization has on vacuolar inorganic phosphate pool size in soybean (Glycine max [L.] Merr.) leaves with respect to phosphorus nutrition and plant development. Phosphate compartmentation between cytoplasmic and vacuolar pools was observed and followed in intact tissue grown hydroponically, at the R2, R4, and R6 growth stages. As phosphorus in the nutrient solution decreased from 0.45 to 0.05 millimolar, the vacuolar phosphate peak became less prominent relative to cytoplasmic phosphate and hexose monophosphate peaks. At a nutrient phosphate concentration of 0.05 millimolar, the vacuolar phosphate peak was not detectable. At higher levels of nutrient phosphate, as plants progressed from the R2 to the R6 growth stage, the vacuolar phosphate peak was the first to disappear, suggesting that storage phosphate was remobilized to a greater extent than metabolic phosphate. Under suboptimal phosphate nutrition (≤ 0.20 millimolar), the hexose monophosphate and cytoplasmic phosphate peaks declined earlier in reproductive development than when phosphate was present in optimal amounts. Under low phosphate concentrations (0.05 millimolar) cytoplasmic phosphate was greatly reduced. Carbon metabolism was coincidently disrupted under low phosphate nutrition as shown by the appearance of large, prominent starch grains in the leaves. Cytoplasmic phosphate, and leaf carbon metabolism dependent on it, are buffered by vacuolar phosphate until late stages of reproductive growth. Images Figure 4 PMID:16666705

Pentose phosphates in nucleoside interconversion and catabolism.

Science.gov (United States)

Tozzi, Maria G; Camici, Marcella; Mascia, Laura; Sgarrella, Francesco; Ipata, Piero L

2006-03-01

Ribose phosphates are either synthesized through the oxidative branch of the pentose phosphate pathway, or are supplied by nucleoside phosphorylases. The two main pentose phosphates, ribose-5-phosphate and ribose-1-phosphate, are readily interconverted by the action of phosphopentomutase. Ribose-5-phosphate is the direct precursor of 5-phosphoribosyl-1-pyrophosphate, for both de novo and 'salvage' synthesis of nucleotides. Phosphorolysis of deoxyribonucleosides is the main source of deoxyribose phosphates, which are interconvertible, through the action of phosphopentomutase. The pentose moiety of all nucleosides can serve as a carbon and energy source. During the past decade, extensive advances have been made in elucidating the pathways by which the pentose phosphates, arising from nucleoside phosphorolysis, are either recycled, without opening of their furanosidic ring, or catabolized as a carbon and energy source. We review herein the experimental knowledge on the molecular mechanisms by which (a) ribose-1-phosphate, produced by purine nucleoside phosphorylase acting catabolically, is either anabolized for pyrimidine salvage and 5-fluorouracil activation, with uridine phosphorylase acting anabolically, or recycled for nucleoside and base interconversion; (b) the nucleosides can be regarded, both in bacteria and in eukaryotic cells, as carriers of sugars, that are made available though the action of nucleoside phosphorylases. In bacteria, catabolism of nucleosides, when suitable carbon and energy sources are not available, is accomplished by a battery of nucleoside transporters and of inducible catabolic enzymes for purine and pyrimidine nucleosides and for pentose phosphates. In eukaryotic cells, the modulation of pentose phosphate production by nucleoside catabolism seems to be affected by developmental and physiological factors on enzyme levels.

Meal phosphate variability does not support fixed dose phosphate binder schedules for patients treated with peritoneal dialysis: a prospective cohort study.

Science.gov (United States)

Leung, Simon; McCormick, Brendan; Wagner, Jessica; Biyani, Mohan; Lavoie, Susan; Imtiaz, Rameez; Zimmerman, Deborah

2015-12-09

Removal of phosphate by peritoneal dialysis is insufficient to maintain normal serum phosphate levels such that most patients must take phosphate binders with their meals. However, phosphate 'counting' is complicated and many patients are simply prescribed a specific dose of phosphate binders with each meal. Therefore, our primary objective was to assess the variability in meal phosphate content to determine the appropriateness of this approach. In this prospective cohort study, adult patients with ESRD treated with peritoneal dialysis and prescribed phosphate binder therapy were eligible to participate. Participants were excluded from the study if they were unable to give consent, had hypercalcemia, were visually or hearing impaired or were expected to receive a renal transplant during the time of the study. After providing informed consent, patients kept a 3-day diet diary that included all foods and beverages consumed in addition to portion sizes. At the same time, patients documented the amount of phosphate binders taken with each meal. The phosphate content of the each meal was estimated using ESHA Food Processor SQL Software by a registered dietitian. Meal phosphate and binder variability were estimated by the Intra Class Correlation Coefficient (ICC) where 0 indicates maximal variability and 1 indicates no variability. Seventy-eight patients consented to participate in the study; 18 did not complete the study protocol. The patients were 60 (± 17) years, predominately male (38/60) and Caucasian (51/60). Diabetic nephropathy was the most common cause of end stage kidney disease. The daily phosphate intake including snacks ranged from 959 ± 249 to 1144 ± 362 mg. The phosphate ICC by meal: breakfast 0.63, lunch 0.16; supper 0.27. The phosphate binder ICC by meal: breakfast 0.68, lunch 0.73, supper 0.67. The standard prescription of a set number of phosphate binders with each meal is not supported by the data; patients do not appear to be adjusting their

Comparative study on in vitro biocompatibility of synthetic octacalcium phosphate and calcium phosphate ceramics used clinically.

Science.gov (United States)

Morimoto, Shinji; Anada, Takahisa; Honda, Yoshitomo; Suzuki, Osamu

2012-08-01

The present study was designed to investigate the extent to which calcium phosphate bone substitute materials, including osteoconductive octacalcium phosphate (OCP), display cytotoxic and inflammatory responses based on their dissolution in vitro. Hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) ceramics, which are clinically used, as well as dicalcium phosphate dihydrate (DCPD) and synthesized OCP were compared. The materials were well characterized by chemical analysis, x-ray diffraction and Fourier transform infrared spectroscopy. Calcium and phosphate ion concentrations and the pH of culture media after immersion of the materials were determined. The colony forming rate of Chinese hamster lung fibroblasts was estimated with extraction of the materials. Proliferation of bone marrow stromal ST-2 cells and inflammatory cytokine TNF-α production by THP-1 cells grown on the material-coated plates were examined. The materials had characteristics that corresponded to those reported. DCPD was shown to dissolve the most in the culture media, with a marked increase in phosphate ion concentration and a reduction in pH. ST-2 cells proliferated well on the materials, with the exception of DCPD, which markedly inhibited cellular growth. The colony forming capacity was the lowest on DCPD, while that of the other calcium phosphates was not altered. In contrast, TNF-α was not detected even in cells grown on DCPD, suggesting that calcium phosphate materials are essentially non-inflammatory, while the solubility of the materials can affect osteoblastic and fibroblastic cellular attachment. These results indicate that OCP is biocompatible, which is similar to the materials used clinically, such as HA. Therefore, OCP could be clinically used as a biocompatible bone substitute material.

Analyses of uranium in some phosphate commercial products

International Nuclear Information System (INIS)

Kamel, N.H.M.; Sohsah, M.; Mohammad, H.M.; Sadek, M.

2005-01-01

The raw materials used in manufacturing of phosphate fertilizer products were derived from rocks. Rocks contain a remarkable of natural radioactivity. Uranium and phosphorous were originally initiated at the same time of the initiated rocks. The purpose of this research is to investigate solubility of uranium phosphate species at the phosphate fertilizer samples, samples including; raw phosphate material, single super phosphates (SSP) granules and powdered, triple super phosphates (TSP) and phosphogypsum samples were obtained from Abu-Zabal factory in Egypt. Solubility of uranium phosphate species was estimated. It was found that, less than half of the uranium phosphate species are soluble in water. The soluble uranium may be enter into the food chains by plant. Therefore, restriction should be done in order to limit contamination of land and the public

Phosphate Reduction in Emulsified Meat Products: Impact of Phosphate Type and Dosage on Quality Characteristics.

Science.gov (United States)

Glorieux, Seline; Goemaere, Olivier; Steen, Liselot; Fraeye, Ilse

2017-09-01

Phosphate reduction is of important industrial relevance in the manufacturing of emulsified meat products because it may give rise to a healthier product. The effect of seven different phosphate types was tested on the physicochemical and quality characteristics to select the most promising phosphate type for further cooked sausage manufacturing. Next, phosphate mass fraction was gradually reduced. Tetrasodium di- or pyrophosphate (TSPP) and sodium tripolyphosphate (STPP) increased pH, reduced structural properties, resulted in the highest emulsion stability, lowest cooking loss and had little effect on hardness. Based on the viscoelastic properties, a minimum mass fraction of 0.06% TSPP was sufficient to obtain an acceptable quality product. Rheology proved to be a very useful tool to evaluate the quality of meat products, as it gives insight in the structure of the meat product and especially the functional properties of meat proteins. Based on the obtained results, it can be concluded that the current amount of phosphate added to emulsified meat products can be significantly reduced with minimal loss of product quality.

Preparation of the pur uranium-metal; La preparation de l'uranium-metal pur

Energy Technology Data Exchange (ETDEWEB)

Goldschmidt, B; Vertes, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

A detailed description of the chemical processes used to prepare in the factory of Bouchet of the CEA (Seine-Et-Oise) pur metal uranium with either relatively rich ores, or extracts coming of physical or chemical treatment of poor ores. The nitric treatment of ores succeeds to the production of uranate of impure sodium carbonate. This last last product is dissolved in nitric acid and the uranyl nitrate is extracted by tributyl-phosphate diluted in an inert solvent. The uranyl nitrate pure is re-extracted and successively transformed in uranium peroxide, in orange oxide then in brown oxide which is transformed in fluoride by the anhydrous hydrofluoric acid. Uranate fluoride is then reduced in metal by the pure calcium with an yield superior to 99%. (authors) [French] Description detaillee des procedes chimiques mis en jeu pour preparer a l'Usine du Bouchet du Commissariat a l'Energie Atomique (Seine-et-Oise) l'uranium metal pur a partir soit de minerais relativement riches, soit de concentres provenant de traitement physique ou chimique de minerais pauvres. Le traitement nitrique des minerais aboutit a la production d'uranate de soude impur. Ce dernier est a son tour dissous dans l'acide nitrique et le nitrate d'uranyle est extrait par du tributyl-phosphate dilue par un solvant inerte. Le nitrate d'uranyle pur reextrait est transforme successivement en peroxyde d'uranium, en oxyde orange puis en oxyde brun qui est transforme en fluorure par l'acide fluorhydrique anhydre. Le fluorure uraneux est reduit en metal par le calcium pur avec un rendement superieur a 99 %. (auteurs)

[Phosphate-solubilizing activity of aerobic methylobacteria].

Science.gov (United States)

Agafonova, N V; Kaparullina, E N; Doronina, N V; Trotsenko, Iu A

2014-01-01

Phosphate-solubilizing activity was found in 14 strains of plant-associated aerobic methylobacteria belonging to the genera Methylophilus, Methylobacillus, Methylovorus, Methylopila, Methylobacterium, Delftia, and Ancyclobacter. The growth of methylobacteria on medium with methanol as the carbon and energy source and insoluble tricalcium phosphate as the phosphorus source was accompanied by a decrease in pH due to the accumulation of up to 7 mM formic acid as a methanol oxidation intermediate and by release of 120-280 μM phosphate ions, which can be used by both bacteria and plants. Phosphate-solubilizing activity is a newly revealed role of methylobacteria in phytosymbiosis.

Isolation and identification of a phosphate solubilising fungus from soil of a phosphate mine in Chaluse, Iran

Directory of Open Access Journals (Sweden)

Raheleh Jamshidi

2016-07-01

Full Text Available Microbial solubilisation of phosphorus from insoluble phosphates is an environmental friendly and cost effective approach in sustainable soil management. Introducing the indigenous microorganisms to soil requires shorter adaptation period and causes fewer ecological distortions than exogenous microorganisms. This study was conducted to isolate and identify the indigenous fungi for phosphate solubilisation in Mazandaran, Iran. A potent phosphate solubilising fungus was isolated from an Iranian phosphate mine and selected for solubilisation of rock phosphate (RP. The identified fungus was characterised by calmodulin-based polymerase chain reaction method as Aspergillus tubingensis SANRU (Sari Agricultural Sciences and Natural Resources University. The phosphate solubilisation ability of the fungal strain was carried out in shake-flask leaching experiments containing various concentrations of RP (1%, 2%, 4%, or 8% w/v. The maximum P solubilisation rate of 347 mg/l was achieved at 1% of RP concentration on day 9. The regression analysis indicated that the P solubilised mainly through acidification. This study shows the possibility of using A. tubingensis SANRU for application in the management of P fertilisation.

Translocation of metal phosphate via the phosphate inorganic transport system of Escherichia coli

NARCIS (Netherlands)

van Veen, H.W; Abee, T.; Kortstee, G.J J; Konings, W.N; Zehnder, A.J B

1994-01-01

P-i transport via the phosphate inorganic transport system (Pit) of Escherichia coil was studied in natural and artificial membranes. P-i uptake via Pit is dependent on the presence of divalent cations, like Mg2+, Ca2+, Co2+, or Mn2+, which form a soluble, neutral metal phosphate (MeHPO(4)) complex.

Co-precipitation of phosphate and iron limits mitochondrial phosphate availability in Saccharomyces cerevisiae lacking the yeast frataxin homologue (YFH1).

Science.gov (United States)

Seguin, Alexandra; Santos, Renata; Pain, Debkumar; Dancis, Andrew; Camadro, Jean-Michel; Lesuisse, Emmanuel

2011-02-25

Saccharomyces cerevisiae cells lacking the yeast frataxin homologue (Δyfh1) accumulate iron in the mitochondria in the form of nanoparticles of ferric phosphate. The phosphate content of Δyfh1 mitochondria was higher than that of wild-type mitochondria, but the proportion of mitochondrial phosphate that was soluble was much lower in Δyfh1 cells. The rates of phosphate and iron uptake in vitro by isolated mitochondria were higher for Δyfh1 than wild-type mitochondria, and a significant proportion of the phosphate and iron rapidly became insoluble in the mitochondrial matrix, suggesting co-precipitation of these species after oxidation of iron by oxygen. Increasing the amount of phosphate in the medium decreased the amount of iron accumulated by Δyfh1 cells and improved their growth in an iron-dependent manner, and this effect was mostly transcriptional. Overexpressing the major mitochondrial phosphate carrier, MIR1, slightly increased the concentration of soluble mitochondrial phosphate and significantly improved various mitochondrial functions (cytochromes, [Fe-S] clusters, and respiration) in Δyfh1 cells. We conclude that in Δyfh1 cells, soluble phosphate is limiting, due to its co-precipitation with iron.

Uranium production from phosphates

International Nuclear Information System (INIS)

Ketzinel, Z.; Folkman, Y.

1979-05-01

According to estimates of the world's uranium consumption, exploitation of most rich sources is expected by the 1980's. Forecasts show that the rate of uranium consumption will increase towards the end of the century. It is therefore desirable to exploit poor sources not yet in use. In the near future, the most reasonable source for developing uranium is phosphate rock. Uranium reserves in phosphates are estimated at a few million tons. Production of uranium from phosphates is as a by-product of phosphate rock processing and phosphoric acid production; it will then be possible to save the costs incurred in crushing and dissolving the rock when calculating uranium production costs. Estimates show that the U.S. wastes about 3,000 tons of uranium per annum in phosphoric acid based fertilisers. Studies have also been carried out in France, Yugoslavia and India. In Israel, during the 1950's, a small plant was operated in Haifa by 'Chemical and Phosphates'. Uranium processes have also been developed by linking with the extraction processes at Arad. Currently there is almost no activity on this subject because there are no large phosphoric acid plants which would enable production to take place on a reasonable scale. Discussions are taking place about the installation of a plant for phosphoric acid production utilising the 'wet process', producing 200 to 250,000 tons P 2 O 5 per annum. It is necessary to combine these facilities with uranium production plant. (author)

Electrical properties of phosphate glasses

International Nuclear Information System (INIS)

Mogus-Milankovic, A; Santic, A; Reis, S T; Day, D E

2009-01-01

Investigation of the electrical properties of phosphate glasses where transition metal oxide such as iron oxide is the network former and network modifier is presented. Phosphate glasses containing iron are electronically conducting glasses where the polaronic conduction is due to the electron hopping from low to high iron valence state. The identification of structural defects caused by ion/polaron migration, the analysis of dipolar states and electrical conductivity in iron phosphate glasses containing various alkali and mixed alkali ions was performed on the basis of the impedance spectroscopy (IS). The changes in electrical conductivity from as-quenched phosphate glass to fully crystallized glass (glass-ceramics) by IS are analyzed. A change in the characteristic features of IS follows the changes in glass and crystallized glass network. Using IS, the contribution of glass matrix, crystallized grains and grain boundary to the total electrical conductivity for iron phosphate glasses was analyzed. It was shown that decrease in conductivity is caused by discontinuities in the conduction pathways as a result of the disruption of crystalline network where two or more crystalline phases are formed. Also, phosphate-based glasses offer a unique range of biomaterials, as they form direct chemical bonding with hard/soft tissue. The surface charges of bioactive glasses are recognized to be the most important factors in determining biological responses. The improved bioactivity of the bioactive glasses as a result of the effects of the surface charges generated by electrical polarization is discussed.

Counter current extraction of phosphoric acid: Food grade acid production

International Nuclear Information System (INIS)

Shlewit, H.; AlIbrahim, M.

2009-01-01

Extraction, scrubbing and stripping of phosphoric acid from the Syrian wet-phosphoric acid was carried out using Micro-pilot plant of mixer settler type of 8 l/h capacity. Tributyl phosphate (TBP)/di-isopropyl ether (DIPE) in kerosene was used as extractant. Extraction and stripping equilibrium curves were evaluated. The number of extraction and stripping stages to achieve the convenient and feasible yield was determined. Detailed flow sheet was suggested for the proposed continuous process. Data obtained include useful information for the design of phosphoric acid extraction plant. The produced phosphoric acid was characterized using different analytical techniques. (author)

Waste management analysis for the nuclear fuel cycle. I. Actinide recovery from aqueous salt wastes

International Nuclear Information System (INIS)

Martella, L.L.; Navratil, J.D.

1979-01-01

A preliminary feasibility study of solvent extraction methods has been completed for removing actinides from selected salt wastes likely to be produced during reactor fuel fabrication and reprocessing. The use of a two-step solvent extraction system, tributyl phosphate (TBP) followed by a bidentate organophosphorus extractant (DHDECMP), appears most efficient for removing actinides from salt waste. The TBP step would remove most of the plutonium and >99.99% of the uranium. The second step, using DHDECMP, would remove >99.91% of the americium, the remaining plutonium (>99.98%), and other actinides from the acidified salt waste

Formation of adduct of cerium (4) thenoyltrifluoroacetonate

International Nuclear Information System (INIS)

Anyfrieva, S.I.; Polyakova, G.V.; Snezhko, N.I.; Pechurova, N.I.; Martynenko, L.I.; Spitsyn, V.I.

1981-01-01

Adduct formation of thenoyltrifluoroacetonate of Ce(4) [Ce(TTFA) 4 ] with seven nitrogen- and oxygen-containing donor additional ligands is studied using the methods of IR-spectroscopy, derivatography, X-ray phase analysis. The presence of formation of Ce(TTFA) 4 adducts with phosphorus-containing additional ligands tributyl phosphate (TBP), trioctylphosphine oxide (TOPO), triphenylphosphine oxide (TPPO); α, α'-dipyridyl (Dipy) and o-phenanthroline (Phen) is established. The adduct Ce(TTFA) 4 stable to reduction is formed with Dipy, and in the case of Phen, TBP, TOPO, TPPO in the process of adduct formation the reduction of Ce(4) to Ce(3) takes place [ru

Plutonium recovery from carbonate wash solutions

International Nuclear Information System (INIS)

Gray, J.H.; Reif, D.J.; Chostner, D.F.; Holcomb, H.P.

1991-01-01

540Periodically higher than expected levels of plutonium are found in carbonate solutions used to wash second plutonium cycle solvent. The recent accumulation of plutonium in carbonate wash solutions has led to studies to determine the cause of that plutonium accumulation, to evaluate the quality of all canyon solvents, and to develop additional criteria needed to establish when solvent quality is acceptable. Solvent from three canyon solvent extraction cycles was used to evaluate technology required to measure tributyl phosphate (TBP) degradation products and was used to evaluate solvent quality criteria during the development of plutonium recovery processes. 1 fig

Hydrogen permeation resistant phosphate coatings

International Nuclear Information System (INIS)

McGuire, J.C.

1979-01-01

A method for reducing hydrogen diffusion through metal wherein the metal is coated with a phosphate-radical-containing, phosphate-glass-forming material on at least one surface thereof. The coating is then heated to at least 350 0 C to form a phosphate glass. This method is especially applicable to nuclear reactors to minimize tritium diffusion. The coating is preferably formed with a solution of phosphoric acid which may also contain compounds such as MnSO 4 , SiO 2 and Na 2 Cr 2 0 7 . (author)

Hydrogen permeation resistant phosphate coatings

International Nuclear Information System (INIS)

McGuire, J.C.

1979-01-01

A method for reducing hydrogen diffusion through metal is described. The metal is coated with a phosphate-radical-containing, phosphate-glass-forming material on at least one surface. The coating is then heated to at least 350 0 C to form a phosphate glass. This method is especially applicable to nuclear reactors to minimize tritium diffusion. The coating is preferably formed with a solution of phosphoric acid which may also contain compounds such as MnSO 4 , SiO 2 and Na 2 Cr 2 O 7 . (author)

Transfer of Some Major and Trace Elements From Phosphate Rock to Super-Phosphate Fertilizers

International Nuclear Information System (INIS)

El-Reefya, H.I.; Bin-Jaz, A.A.; Zaied, M.E.; Badran, H.M.; Badran, H.M.

2014-01-01

This study assesses the transfer of some major and trace elements from phosphate rock (PR) to single (SSP) and triple (TSP) superphosphate fertilizers. Samples from a fertilizer plant and local market were collected and analyzed using inductively coupled plasma spectrometer. Cluster analysis indicated that the inner-relationship among the concentration of the elements in PR, SSP, and TSP are different. Only one element (Mo) has concentration in SSP higher than phosphate rock. The production process of these two types of superphosphate leads to transfer higher portion of Mn, B, Cu, Mo, Sr, and V present in the phosphate rock to SSP than TSP. The potentially hazardous element Cd is also transmitted more to SSP than TSP, and Cr is equally transferred to both types. The mean elemental concentrations normalized to the percentage of P 2 O 5 demonstrate that for most elements they are the higher concentrations in SSP are linked to the phosphate contents

Phosphate vibrations as reporters of DNA hydration

Science.gov (United States)

Corcelli, Steven

The asymmetric phosphate stretch vibrational frequency is extraordinarily sensitive to its local solvent environment. Using density functional theory calculations on the model compound dimethyl phosphate, the asymmetric phosphate stretch vibrational frequency was found to shift linearly with the magnitude of an electric field along the symmetry axis of the PO2 moiety (i.e. the asymmetric phosphate stretch is an excellent linear vibrational Stark effect probe). With this linear relationship established, asymmetric phosphate stretch vibrational frequencies were computed during the course of a molecular dynamics simulation of fully hydrated DNA. Moreover, contributions to shifts in the frequencies from subpopulations of water molecules (e.g. backbone, minor groove, major groove, etc.) were calculated to reveal how phosphate vibrations report the onset of DNA hydration in experiments that vary the relative humidity of non-condensing (dry) DNA samples.

Sonochemical precipitation of amorphous uranium phosphates from trialkyl phosphate solutions and their thermal conversion to UP2O7

Czech Academy of Sciences Publication Activity Database

Doroshenko, I.; Žurková, J.; Moravec, Z.; Bezdička, Petr; Pinkas, J.

2015-01-01

Roč. 26, SEP (2015), s. 157-162 ISSN 1350-4177 Institutional support: RVO:61388980 Keywords : Uranium * Phosphates * Sonochemistry * Nuclear waste * Trimethyl phosphate * Triethyl phosphate Subject RIV: CA - Inorganic Chemistry Impact factor: 4.556, year: 2015

Cerebrospinal Fluid Phosphate in Delirium after Hip Fracture

Directory of Open Access Journals (Sweden)

Ane-Victoria Idland

2017-09-01

Full Text Available Aims: Phosphate is essential for neuronal activity. We aimed to investigate whether delirium is associated with altered phosphate concentrations in cerebrospinal fluid (CSF and serum. Methods: Seventy-seven patients with hip fracture were assessed for delirium before and after acute surgery. Prefracture dementia was diagnosed by an expert panel. Phosphate was measured in CSF obtained immediately before spinal anesthesia (n = 77 and in serum (n = 47. CSF from 23 cognitively healthy elderly patients undergoing spinal anesthesia was also analyzed. Results: Hip fracture patients with prevalent delirium had higher CSF phosphate concentrations than those without delirium (median 0.63 vs. 0.55 mmol/L, p = 0.001. In analyses stratified on dementia status, this difference was only significant in patients with dementia. Serum phosphate was ∼1 mmol/L; there was no association between serum phosphate concentration and delirium status. CSF phosphate did not correlate with serum levels. Conclusion: Patients with delirium superimposed on dementia have elevated phosphate levels.

Radical-induced dephosphorylation of fructose phosphates in aqueous solution

International Nuclear Information System (INIS)

Zegota, H.; Sonntag, C. von

1981-01-01

Oxygen free N 2 O-saturated aqueous solutions of D-fructose-1-phosphate and D-fructose-6-phosphate were γ-irradiated. Inorganic phosphate and phosphate free sugars (containing four to six carbon atoms) were identified and their G-values measured. D-Fructose-1-phosphate yields (G-values in parentheses) inorganic phosphate (1.6), hexos-2-ulose (0.12), 6-deoxy-2,5-hexodiulose (0.16), tetrulose (0.05) and 3-deoxytetrulose (0.15). D-Fructose-6-phosphate yields inorganic phosphate (1.7), hexos-5-ulose (0.1), 6-deoxy-2,5-hexodiulose (0.36), 3-deoxy-2,5-hexodiulose and 2-deoxyhexos-5-ulose (together 0.18). On treatment with alkaline phosphatase further deoxy sugars were recognized and in fructose-1-phosphate G(6-deoxy-2,5-hexodiulose) was increased to a G-value of 0.4. Dephosphorylation is considered to occur mainly after OH attack at C-5 and C-1 in fructose-1-phosphate and at C-5 and C-6 in fructose-6-phosphate. Reaction mechanisms are discussed. (orig.)

Iron phosphate glass containing simulated fast reactor waste: Characterization and comparison with pristine iron phosphate glass

International Nuclear Information System (INIS)

Joseph, Kitheri; Asuvathraman, R.; Venkata Krishnan, R.; Ravindran, T.R.; Govindaraj, R.; Govindan Kutty, K.V.; Vasudeva Rao, P.R.

2014-01-01

Detailed characterization was carried out on an iron phosphate glass waste form containing 20 wt.% of a simulated nuclear waste. High temperature viscosity measurement was carried out by the rotating spindle method. The Fe 3+ /Fe ratio and structure of this waste loaded iron phosphate glass was investigated using Mössbauer and Raman spectroscopy respectively. Specific heat measurement was carried out in the temperature range of 300–700 K using differential scanning calorimeter. Isoconversional kinetic analysis was employed to understand the crystallization behavior of the waste loaded iron phosphate glass. The glass forming ability and glass stability of the waste loaded glass were also evaluated. All the measured properties of the waste loaded glass were compared with the characteristics of pristine iron phosphate glass

Calcium phosphates for biomedical applications

Directory of Open Access Journals (Sweden)

Maria Canillas

2017-05-01

Full Text Available The history of calcium phosphates in the medicine field starts in 1769 when the first evidence of its existence in the bone tissue is discovered. Since then, the interest for calcium phosphates has increased among the scientific community. Their study has been developed in parallel with new advances in materials sciences, medicine or tissue engineering areas. Bone tissue engineering is the field where calcium phosphates have had a great importance. While the first bioceramics are selected according to bioinert, biocompatibility and mechanical properties with the aim to replace bone tissue damaged, calcium phosphates open the way to the bone tissue regeneration challenge. Nowadays, they are present in the majority of commercial products directed to repair or regenerate damaged bone tissue. Finally, in the last few decades, they have been suggested and studied as drug delivering devices and as vehicles of DNA and RNA for the future generation therapies.

Preparation of calcium phosphate paste

International Nuclear Information System (INIS)

Mohd Reusmaazran Yusof; Norzita Yaacob; Idris Besar; Che Seman Mahmood; Rusnah Mustafa

2010-01-01

Calcium phosphate paste were prepared by mixing between calcium sodium potassium phosphate, Ca 2 NaK (PO 4 ) 2 (CSPP) and monocalcium phosphate monohydrate, Ca(H 2 PO 4 ) 2 .H 2 O (MCPM). CSPP were obtained by reaction between calcium hydrogen phosphate (CaHPO 4 ), potassium carbonate (K 2 CO 3 ) and sodium carbonate (Na 2 CO 3 ) in solid state sintering process followed by quenching in air at 1000 degree Celsius. The paste was aging in simulated body fluid (SBF) for 0.5, 1, 3, 6, 12, 24, 48 hrs, 3, 7 and 14 days. The morphological investigation indicated the formation of apatite crystal were first growth after 24 hours. The obvious growth of apatite crystal was shown at 3 days. The obvious growth of apatite crystal was shown in 7 and 14 days indicated the prediction of paste would have rapid reaction with bone after implantation. (author)

Calcium phosphates for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Canillas, M.; Pena, P.; Aza, A.H. de; Rodriguez, M.A.

2017-07-01

The history of calcium phosphates in the medicine field starts in 1769 when the first evidence of its existence in the bone tissue is discovered. Since then, the interest for calcium phosphates has increased among the scientific community. Their study has been developed in parallel with new advances in materials sciences, medicine or tissue engineering areas. Bone tissue engineering is the field where calcium phosphates have had a great importance. While the first bioceramics are selected according to bioinert, biocompatibility and mechanical properties with the aim to replace bone tissue damaged, calcium phosphates open the way to the bone tissue regeneration challenge. Nowadays, they are present in the majority of commercial products directed to repair or regenerate damaged bone tissue. Finally, in the last few decades, they have been suggested and studied as drug delivering devices and as vehicles of DNA and RNA for the future generation therapies. (Author)

Conditions promoting and restraining agronomic effectiveness of water-insoluble phosphate sources, in particular phosphate rock (PR): I. Indices of phosphate rock use opportunity (PRUOIS) and of phosphate rock suitability for direct use (PRSIDU)

International Nuclear Information System (INIS)

Borlan, Z.; Gavriluta, I.; Soare, M.; Stefanescu, D.; Alexandrescu, A.

2002-01-01

Several issues of phosphate rock (PR) use are discussed in this paper. Maize for green fodder (Zea mays L) and ryegrass (Lolium multiflorum Lam.) were grown in 7 kg of dry soil and in small pots of 1.25 kg dry soil capacity, respectively, on several base unsaturated soils belonging to Hapludoll and Hapludalf soil groups. The amount of phosphate rock (PR) to apply was based on experimental data considering soil adsorbed acidity (Ah), humus content (H 2 ), cation exchange capacity (T), sum of exchangeable bases (SEB) and mobile (easily soluble) phosphate content (P A L) in the soil. The factors were combined in a rock phosphate use, opportunity index of the soil (PRUOIS): PRUOIS=(A h *H 2 *100)/SEB*10 0.0245*P AL Rock phosphate suitability for direct use was evaluated by means of the rate of PR-P dissolution (PRPRS) in a 0.6% ammonium heptamolybdate in 0.01M calcium chloride solution (ppm P) and by carbonate content (%CaCO 3 ) in PR. Both of these parameters combined provided a phosphate rock suitability index for direct use (PRSIDU): PRSIDU [ppmP/min]=PRPRS*(1-0.03*CaCO 3 ) Water insoluble P sources studied were PR from Kola-Russia, Morocco, Kneifiss-Siria, El Hassa-Jordan, Gafsa- Tunisia, North-Carolina (USA), and Arad-Israel. All PRs were compared with TSP applied at the same rate of P. Neither PRUOIS or PRSIDU considered separately could satisfactorily explain the variance of PR efficiency. An index obtained by multiplicative combination of PRUOIS x PRSIDU did correlate significantly with indices on the agronomic efficiency of PR. (author)

Impaired Phosphate Tolerance Revealed With an Acute Oral Challenge.

Science.gov (United States)

Turner, Mandy E; White, Christine A; Hopman, Wilma M; Ward, Emilie C; Jeronimo, Paul S; Adams, Michael A; Holden, Rachel M

2018-01-01

Elevated serum phosphate is consistently linked with cardiovascular disease (CVD) events and mortality in the setting of normal and impaired kidney function. However, serum phosphate does not often exceed the upper limit of normal until glomerular filtration rate (GFR) falls below 30 mL/min/m 2 . It was hypothesized that the response to an oral, bioavailable phosphate load will unmask impaired phosphate tolerance, a maladaptation not revealed by baseline serum phosphate concentrations. In this study, rats with varying kidney function as well as normo-phosphatemic human subjects, with inulin-measured GFR (13.2 to 128.3mL/min), received an oral phosphate load. Hormonal and urinary responses were evaluated over 2 hours. Results revealed that the more rapid elevation of serum phosphate was associated with subjects and rats with higher levels of kidney function, greater responsiveness to acute changes in parathyroid hormone (PTH), and significantly more urinary phosphate at 2 hours. In humans, increases in urinary phosphate to creatinine ratio did not correlate with baseline serum phosphate concentrations but did correlate strongly to early increase of serum phosphate. The blunted rise in serum phosphate in rats with CKD was not the result of altered absorption. This result suggests acute tissue deposition may be altered in the setting of kidney function impairment. Early recognition of impaired phosphate tolerance could translate to important interventions, such as dietary phosphate restriction or phosphate binders, being initiated at much higher levels of kidney function than is current practice. © 2017 American Society for Bone and Mineral Research. © 2017 American Society for Bone and Mineral Research.

Phosphate Reduction in Emulsifi ed Meat Products: Impact of Phosphate Type and Dosage on Quality Characteristics

Directory of Open Access Journals (Sweden)

Seline Glorieux

2017-01-01

Full Text Available Phosphate reduction is of important industrial relevance in the manufacturing of emulsifi ed meat products because it may give rise to a healthier product. The eff ect of seven diff erent phosphate types was tested on the physicochemical and quality characteristics to select the most promising phosphate type for further cooked sausage manufacturing. Next, phosphate mass fraction was gradually reduced. Tetrasodium di- or pyrophosphate (TSPP and sodium tripolyphosphate (STPP increased pH, reduced structural properties, resulted in the highest emulsion stability, lowest cooking loss and had litt le eff ect on hardness. Based on the viscoelastic properties, a minimum mass fraction of 0.06 % TSPP was suffi cient to obtain an acceptable quality product. Rheology proved to be a very useful tool to evaluate the quality of meat products, as it gives insight in the structure of the meat product and especially the functional properties of meat proteins. Based on the obtained results, it can be concluded that the current amount of phosphate added to emulsifi ed meat products can be signifi cantly reduced with minimal loss of product quality.

Biotemplate synthesis of monodispersed iron phosphate hollow microspheres

International Nuclear Information System (INIS)

Cao Feng; Li Dongxu

2010-01-01

Monodispersed iron phosphate hollow microspheres with a high degree of crystallization were prepared through a facile in situ deposition method using rape pollen grains as a biotemplate. The functional group on the surface of the pollen grains could adsorb Fe 3+ , which provided the nucleation sites for growth of iron phosphate nanoparticles. After being sintered at 600 deg. C for 10 h, the pollen grains were removed and iron phosphate hollow microspheres were obtained. A scanning electron microscope and x-ray diffraction were applied to characterize the morphology and crystalline structure of the pollen grains, iron phosphate-coated pollen grains and iron phosphate hollow microspheres. Differential scanning calorimetry and thermogravity analyses were performed to investigate the thermal behavior of the iron phosphate-coated pollen grains during the calcinations. Energy dispersive spectroscopy and Fourier transform infrared spectroscopy were utilized to investigate the interaction between the pollen grains and iron phosphate. The effect of the pollen wall on the surface morphology of these iron phosphate hollow microspheres was also proven in this work.

Biotemplate synthesis of monodispersed iron phosphate hollow microspheres

Energy Technology Data Exchange (ETDEWEB)

Cao Feng; Li Dongxu, E-mail: dongxuli@njut.edu.c [College of Materials Science and Engineering, Nanjing University of Technology, Jiangsu Nanjing 210009 (China)

2010-03-15

Monodispersed iron phosphate hollow microspheres with a high degree of crystallization were prepared through a facile in situ deposition method using rape pollen grains as a biotemplate. The functional group on the surface of the pollen grains could adsorb Fe{sup 3+}, which provided the nucleation sites for growth of iron phosphate nanoparticles. After being sintered at 600 deg. C for 10 h, the pollen grains were removed and iron phosphate hollow microspheres were obtained. A scanning electron microscope and x-ray diffraction were applied to characterize the morphology and crystalline structure of the pollen grains, iron phosphate-coated pollen grains and iron phosphate hollow microspheres. Differential scanning calorimetry and thermogravity analyses were performed to investigate the thermal behavior of the iron phosphate-coated pollen grains during the calcinations. Energy dispersive spectroscopy and Fourier transform infrared spectroscopy were utilized to investigate the interaction between the pollen grains and iron phosphate. The effect of the pollen wall on the surface morphology of these iron phosphate hollow microspheres was also proven in this work.

The Effect of Moderate Dietary Protein and Phosphate Restriction on Calcium-Phosphate Homeostasis in Healthy Older Cats.

Science.gov (United States)

Geddes, R F; Biourge, V; Chang, Y; Syme, H M; Elliott, J

2016-09-01

Dietary phosphate and protein restriction decreases plasma PTH and FGF-23 concentrations and improves survival time in azotemic cats, but has not been examined in cats that are not azotemic. Feeding a moderately protein- and phosphate-restricted diet decreases PTH and FGF-23 in healthy older cats and thereby slows progression to azotemic CKD. A total of 54 healthy, client-owned cats (≥ 9 years). Prospective double-blinded randomized placebo-controlled trial. Cats were assigned to test diet (protein 76 g/Mcal and phosphate 1.6 g/Mcal) or control diet (protein 86 g/Mcal and phosphate 2.6 g/Mcal) and monitored for 18 months. Changes in variables over time and effect of diet were assessed by linear mixed models. A total of 26 cats ate test diet and 28 cats ate control diet. There was a significant effect of diet on urinary fractional excretion of phosphate (P = 0.045), plasma PTH (P = 0.005), and ionized calcium concentrations (P = 0.018), but not plasma phosphate, FGF-23, or creatinine concentrations. Plasma PTH concentrations did not significantly change in cats fed the test diet (P = 0.62) but increased over time in cats fed the control diet (P = 0.001). There was no significant treatment effect of the test diet on development of azotemic CKD (3 of 26 (12%) test versus 3 of 28 (11%) control, odds ratio 1.09 (95% CI 0.13-8.94), P = 0.92). Feeding a moderately protein- and phosphate-restricted diet has effects on calcium-phosphate homeostasis in healthy older cats and is well tolerated. This might have an impact on renal function and could be useful in early chronic kidney disease. Copyright © 2016 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

Isolation of phosphatase-producing phosphate solubilizing bacteria from Loriya hot spring: Investigation of phosphate solubilizing in the presence of different parameters

Directory of Open Access Journals (Sweden)

Maryam Parhamfar

2014-04-01

Full Text Available Introduction: Biofertilizers are the microorganisms that can convert useless nutrient to usable compounds. Unlike fertilizer, cost of biofertilizer production is low and doesn’t produce ecosystem pollution. Phosphate fertilizers can be replaced by phosphate biofertilizer to produce improvement. So, it is necessary to screen the climate-compatible phosphate solubilizing bacteria. Materials and methods: In this project samples were picked up from Loriya hot spring, which are located in Jiroft. Samples were incubated in PKV medium for 3 days. Screening of phosphate solubilizing bacteria was performed on the specific media, based on clear area diameter. The best bacterium was identified based on 16s rDNA gene. Phosphate solubilizing activity of this strain was considered in different carbon, nitrogen, phosphate and pH sources. Results: Sequence alignment and phylogenetic tree results show that B. sp. LOR033 is closely related to Bacillus licheniformis, with 97% homology. In addition, results show that maximum enzyme production was performed after 2 days that incubation pH was decreased simultaneously when the time was increased. Carbon sources investigation show that glucose is the most appropriate in enzyme production and phosphate releasing. Furthermore, results show that the optimum initial pH for phytase production was pH5.0. Different phosphate sources show that tricalcium phosphate has the suitable effect on enzyme activity in three days of incubation. Discussion and conclusion: Phosphatase enzyme production capacity, growth in acidic pH and phosphate solubilizing potential in different salt and phosphate sources show that this strain has considerable importance as biofertilizers.

Aqueous phosphate removal using nanoscale zero-valent iron

International Nuclear Information System (INIS)

Almeelbi, Talal; Bezbaruah, Achintya

2012-01-01

Nanoscale zero-valent iron (NZVI) particles have been used for the remediation of a wide variety of contaminants. NZVI particles have high reactivity because of high reactive surface area. In this study, NZVI slurry was successfully used for phosphate removal and recovery. Batch studies conducted using different concentrations of phosphate (1, 5, and 10 mg PO 4 3− -P/L with 400 mg NZVI/L) removed ∼96 to 100 % phosphate in 30 min. Efficacy of the NZVI in phosphate removal was found to 13.9 times higher than micro-ZVI (MZVI) particles with same NZVI and MZVI surface area concentrations used in batch reactors. Ionic strength, sulfate, nitrate, and humic substances present in the water affected in phosphate removal by NZVI but they may not have any practical significance in phosphate removal in the field. Phosphate recovery batch study indicated that better recovery is achieved at higher pH and it decreased with lowering of the pH of the aqueous solution. Maximum phosphate recovery of ∼78 % was achieved in 30 min at pH 12. The successful rapid removal of phosphate by NZVI from aqueous solution is expected to have great ramification for cleaning up nutrient rich waters.

Research and engineering assessment of biological solubilization of phosphate

Energy Technology Data Exchange (ETDEWEB)

Rogers, R.D.; McIlwain, M.E.; Losinski, S.J.; Taylor, D.D.

1993-03-01

This research and engineering assessment examined a microbial phosphate solubilization process as a method of recovering phosphate from phosphorus containing ore compared to the existing wet acid and electric arc methods. A total of 860 microbial isolates, collected from a range of natural environments were tested for their ability to solubilize phosphate from rock phosphate. A bacterium (Pseudomonas cepacia) was selected for extensive characterization and evaluation of the mechanism of phosphate solubilization and of process engineering parameters necessary to recover phosphate from rock phosphate. These studies found that concentration of hydrogen ion and production of organic acids arising from oxidation of the carbon source facilitated microbial solubilization of both pure chemical insoluble phosphate compounds and phosphate rock. Genetic studies found that phosphate solubilization was linked to an enzyme system (glucose dehydrogenase). Process-related studies found that a critical solids density of 1% by weight (ore to liquid) was necessary for optimal solubilization. An engineering analysis evaluated the cost and energy requirements for a 2 million ton per year sized plant, whose size was selected to be comparable to existing wet acid plants.

21 CFR 582.1781 - Sodium aluminum phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium aluminum phosphate. 582.1781 Section 582.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Additives § 582.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate. (b) Conditions of...

21 CFR 182.1781 - Sodium aluminum phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium aluminum phosphate. 182.1781 Section 182.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Substances § 182.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate. (b...

Determination of tributyl phosphate (TBP) by precision densimetry : TBP-varsol-HNO/sub 3/ system

Energy Technology Data Exchange (ETDEWEB)

Matsuda, H T; Araujo, B.F. de; Araujo, J.A. de [Instituto de Pesquisas Energeticas e Nucleares, Sao Paulo (Brazil). Centro de Engenharia Quimica

1980-01-01

A simple and rapid method for TBP direct determination is presented, based on precision densimetry, aiming to control solvent concentration in the TBP-Varsol system during the reprocessing of irradiated uranium. The method comprises the determination of the density of liquids or gases by electronic measurement of the variation in the frequency (f) or period (T = 1/f) of a glass oscillator containing the liquid or the gas.

The oxidation of uranium(IV) ions by nitrous acid in 30% tri-butyl phosphate

International Nuclear Information System (INIS)

Koltunov, V.S.; Marchenko, V.I.; Savilova, O.A.; Dvoeglazov, K.N.; Taylor, R.J.

2004-01-01

The kinetics of the oxidation of U(IV) ions by nitrous acid in a 30% TBP solution have been determined. The rate equation was found to be: - d[U(IV)] / dt = k 2a [U(IV)][HNO 2 ][HNO 3 ][H 2 O] / [HNO 3 ] 2 + β 3 [HNO 3 ][H 2 O] + β 4 [H 2 O] 2 , where, k 2a = 0.405 ± 0.055 M -1 min -1 at 55 C (β 3 ∼ 0.08; β 4 ∼ 0.007) and the activation energy was E = 112 ± 17 kJ mol -1 . The reaction mechanism appeared to involve interaction with the 1 st hydrolysis product of U(IV)-UOH 3+ . The data is compared with a previous study of the nitric acid oxidation of U(IV) in 30% TBP. This reaction is autocatalytic due to the formation of nitrous acid during the reaction. The kinetics of the decomposition of HNO 2 in 30% TBP (in the absence of U(IV)) have also been reported. (orig.)

Removal mechanism of phosphate from aqueous solution by fly ash.

Science.gov (United States)

Lu, S G; Bai, S Q; Zhu, L; Shan, H D

2009-01-15

This work studied the effectiveness of fly ash in removing phosphate from aqueous solution and its related removal mechanism. The adsorption and precipitation of phosphate by fly ash were investigated separately in order to evaluate their role in the removal of phosphate. Results showed that the removal of phosphate by fly ash was rapid. The removal percentage of phosphate in the first 5min reached 68-96% of the maximum removal of phosphate by fly ash. The removal processes of phosphate by fly ash included a fast and large removal representing precipitation, then a slower and longer removal due to adsorption. The adsorption of phosphate on fly ash could be described well by Freundlich isotherm equation. The pH and Ca2+ concentration of fly ash suspension were decreased with the addition of phosphate, which suggests that calcium phosphate precipitation is a major mechanism of the phosphate removal. Comparison of the relative contribution of the adsorption and precipitation to the total removal of phosphate by fly ash showed that the adsorption accounted for 30-34% of the total removal of phosphate, depending on the content of CaO in fly ash. XRD patterns of the fly ash before and after phosphate adsorption revealed that phosphate salt (CaHPO4 x 2H2O) was formed in the adsorption process. Therefore, the removal of phosphate by fly ash can be attributed to the formation of phosphate precipitation as a brushite and the adsorption on hydroxylated oxides. The results suggested that the use of fly ash could be a promising solution to the removal of phosphate in the wastewater treatment and pollution control.

Isolation and screening phosphate solubilizers from composts as biofertilizer

International Nuclear Information System (INIS)

Phua Choo Kwai Hoe; Khairuddin Abdul Rahim; Latiffah Norddin; Abdul Razak Ruslan

2006-01-01

Phosphate solubilizers are miroorganisms that able to solubilize insoluble inorganic phosphate compounds or hydrolyze organic phosphate to inorganic P. Therefore make the P to be available for plant and consequently enhance plant growth and yield. Recently, phosphate solubilizing microorganisms has been shown to play an important role in the biofertilizer industry. Fifty-one bacterial were isolated from eleven composts. Most of the phosphate solubilizers were isolated from natural farming composted compost and normal composting compost. This shows that both of these composts are more suitable to use for phosphate solubilizer isolation compare commercial composts. Fourteen of the isolates were found to be phosphate solubilizers. These isolates produced a clear zone on the phosphate agar plates, showing their potential as biofertilizer. AP3 was significantly produced the largest clear zone compared with other isolates. This indicates that isolate AP 3 could be a good phosphate solubilizer. Thus, their effectiveness in the greenhouse and field should be evaluated. (Author)

Uranium endowments in phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Ulrich, Andrea E., E-mail: andrea.ulrich@env.ethz.ch [Institute for Environmental Decisions (IED), Natural and Social Science Interface, ETH Zurich Universitässtrasse 22, 8092 Zurich (Switzerland); Institute for Agricultural Sciences, Plant Nutrition, ETH Zurich, Eschikon 33, 8315 Lindau (Switzerland); Schnug, Ewald, E-mail: e.schnug@tu-braunschweig.de [Department of Life Sciences, Technical University of Braunschweig, Pockelsstraße 14, D-38106 Braunschweig (Germany); Prasser, Horst-Michael, E-mail: prasser@lke.mavt.ethz.ch [Institute of Energy Technology, Laboratory of Nuclear Energy Systems, ETH Zurich, Sonneggstrasse 3, 8092 Zurich (Switzerland); Frossard, Emmanuel, E-mail: emmanuel.frossard@usys.ethz.ch [Institute for Agricultural Sciences, Plant Nutrition, ETH Zurich, Eschikon 33, 8315 Lindau (Switzerland)

2014-04-01

This study seeks to identify and specify the components that make up the prospects of U recovery from phosphate rock. A systems approach is taken. The assessment includes i) reviewing past recovery experience and lessons learned; ii) identifying factors that determine recovery; and iii) establishing a contemporary evaluation of U endowments in phosphate rock reserves, as well as the available and recoverable amounts from phosphate rock and phosphoric acid production. We find that in the past, recovery did not fulfill its potential and that the breakup of the Soviet Union worsened then-favorable recovery market conditions in the 1990s. We find that an estimated 5.7 million tU may be recoverable from phosphate rock reserves. In 2010, the recoverable tU from phosphate rock and phosphoric acid production may have been 15,000 tU and 11,000 tU, respectively. This could have filled the world U supply-demand gap for nuclear energy production. The results suggest that the U.S., Morocco, Tunisia, and Russia would be particularly well-suited to recover U, taking infrastructural considerations into account. We demonstrate future research needs, as well as sustainability orientations. We conclude that in order to promote investment and production, it seems necessary to establish long-term contracts at guaranteed prices, ensuring profitability for phosphoric acid producers. - Highlights: • We identify components that underlie the recovery of uranium from phosphate rock. • We estimate that 11,000 tU may have been recoverable from phosphoric acid in 2010. • Recovery is a resource conservation and environmental pollution control strategy. • To ensure investment in recovery technology, profitability needs to be secured.

Uranium endowments in phosphate rock

International Nuclear Information System (INIS)

Ulrich, Andrea E.; Schnug, Ewald; Prasser, Horst-Michael; Frossard, Emmanuel

2014-01-01

This study seeks to identify and specify the components that make up the prospects of U recovery from phosphate rock. A systems approach is taken. The assessment includes i) reviewing past recovery experience and lessons learned; ii) identifying factors that determine recovery; and iii) establishing a contemporary evaluation of U endowments in phosphate rock reserves, as well as the available and recoverable amounts from phosphate rock and phosphoric acid production. We find that in the past, recovery did not fulfill its potential and that the breakup of the Soviet Union worsened then-favorable recovery market conditions in the 1990s. We find that an estimated 5.7 million tU may be recoverable from phosphate rock reserves. In 2010, the recoverable tU from phosphate rock and phosphoric acid production may have been 15,000 tU and 11,000 tU, respectively. This could have filled the world U supply-demand gap for nuclear energy production. The results suggest that the U.S., Morocco, Tunisia, and Russia would be particularly well-suited to recover U, taking infrastructural considerations into account. We demonstrate future research needs, as well as sustainability orientations. We conclude that in order to promote investment and production, it seems necessary to establish long-term contracts at guaranteed prices, ensuring profitability for phosphoric acid producers. - Highlights: • We identify components that underlie the recovery of uranium from phosphate rock. • We estimate that 11,000 tU may have been recoverable from phosphoric acid in 2010. • Recovery is a resource conservation and environmental pollution control strategy. • To ensure investment in recovery technology, profitability needs to be secured

Phosphate Salts

Science.gov (United States)

... body. They are involved in cell structure, energy transport and storage, vitamin function, and numerous other processes ... Phosphate-containing foods and beverages include cola, wine, beer, whole grain cereals, nuts, dairy products and some ...

Synthesis of amorphous acid iron phosphate nanoparticles

International Nuclear Information System (INIS)

Palacios, E.; Leret, P.; Fernández, J. F.; Aza, A. H. De; Rodríguez, M. A.

2012-01-01

A simple method to precipitate nanoparticles of iron phosphate with acid character has been developed in which the control of pH allows to obtain amorphous nanoparticles. The acid aging of the precipitated amorphous nanoparticles favored the P–O bond strength that contributes to the surface reordering, the surface roughness and the increase of the phosphate acid character. The thermal behavior of the acid iron phosphate nanoparticles has been also studied and the phosphate polymerization at 400 °C produces strong compacts of amorphous nanoparticles with interconnected porosity.

Are Polyphosphates or Phosphate Esters Prebiotic Reagents?

Science.gov (United States)

Keefe, Anthony D.; Miller, Stanley L.

1995-01-01

It is widely held that there was a phosphate compound in prebiotic chemistry that played the role of adenosine triphosphate and that the first living organisms had ribose-phosphate in the backbone of their genetic material. However, there are no known efficient prebiotic synthesis of high-energy phosphates or phosphate esters. We review the occurrence of phosphates in nature, the efficiency of the volcanic synthesis of P4O10, the efficiency of polyphosphate synthesis by heating phosphate minerals under geological conditions, and the use of high-energy organic compounds such as cyanamide or hydrogen cyanide. These are shown to be inefficient processes especially when the hydrolysis of the polyphosphates is taken into account. For example, if a whole atmosphere of methane or carbon monoxide were converted to cyanide which somehow synthesized polyphosphates quantitatively, the polyphosphate concentration in the ocean would still have been insignificant. We also attempted to find more efficient high-energy polymerizing agents by spark discharge syntheses, but without success. There may still be undiscovered robust prebiotic syntheses of polyphosphates, or mechanisms for concentrating them, but we conclude that phosphate esters may not have been constituents of the first genetic material. Phosphoanhydrides are also unlikely as prebiotic energy sources.

21 CFR 582.5697 - Riboflavin-5-phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Riboflavin-5-phosphate. 582.5697 Section 582.5697 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5697 Riboflavin-5-phosphate. (a) Product. Riboflavin-5-phosphate. (b) Conditions of use...

Structural Basis for Substrate Specificity in Phosphate Binding (beta/alpha)8-Barrels: D-Allulose 6-Phosphate 3-Epimerase from Escherichia coli K-12

Energy Technology Data Exchange (ETDEWEB)

Chan,K.; Fedorov, A.; Almo, S.; Gerlt, J.

2008-01-01

Enzymes that share the ({beta}/{alpha})8-barrel fold catalyze a diverse range of reactions. Many utilize phosphorylated substrates and share a conserved C-terminal ({beta}/a)2-quarter barrel subdomain that provides a binding motif for the dianionic phosphate group. We recently reported functional and structural studies of d-ribulose 5-phosphate 3-epimerase (RPE) from Streptococcus pyogenes that catalyzes the equilibration of the pentulose 5-phosphates d-ribulose 5-phosphate and d-xylulose 5-phosphate in the pentose phosphate pathway [J. Akana, A. A. Fedorov, E. Fedorov, W. R. P. Novack, P. C. Babbitt, S. C. Almo, and J. A. Gerlt (2006) Biochemistry 45, 2493-2503]. We now report functional and structural studies of d-allulose 6-phosphate 3-epimerase (ALSE) from Escherichia coli K-12 that catalyzes the equilibration of the hexulose 6-phosphates d-allulose 6-phosphate and d-fructose 6-phosphate in a catabolic pathway for d-allose. ALSE and RPE prefer their physiological substrates but are promiscuous for each other's substrate. The active sites (RPE complexed with d-xylitol 5-phosphate and ALSE complexed with d-glucitol 6-phosphate) are superimposable (as expected from their 39% sequence identity), with the exception of the phosphate binding motif. The loop following the eighth {beta}-strand in ALSE is one residue longer than the homologous loop in RPE, so the binding site for the hexulose 6-phosphate substrate/product in ALSE is elongated relative to that for the pentulose 5-phosphate substrate/product in RPE. We constructed three single-residue deletion mutants of the loop in ALSE, ?T196, ?S197 and ?G198, to investigate the structural bases for the differing substrate specificities; for each, the promiscuity is altered so that d-ribulose 5-phosphate is the preferred substrate. The changes in kcat/Km are dominated by changes in kcat, suggesting that substrate discrimination results from differential transition state stabilization. In both ALSE and RPE, the

Mineral phosphate solubilizing bacterial community in agro-ecosystem

African Journals Online (AJOL)

STORAGESEVER

2009-12-15

Dec 15, 2009 ... patterns. Four insoluble phosphate sources; purulia rock phosphate (PRP), mussourie rock phosphate. (MRP) ... community composition analysis (Garland, 1996a) and ..... the threshold level that enabled only a few species to.

[Phosphate solubilization of Aureobasidium pullulan F4 and its mechanism].

Science.gov (United States)

Wang, Dan; Zhan, Jing; Sun, Qing-Ye

2014-07-01

The Aureobasidium pullulans F4 was isolated from the rhizosphere of Hippochaete ramosissimum in Tongguanshan mine wasteland in Tongling City, Anhui Province. Liquid culture was conducted with four kinds of phosphorus sources, calcium phosphate, aluminum phosphate, ferric phosphate and rock phosphate to determine the pH, dissolved phosphorus, phosphorus in the bacteria and organic acid in the solution. The results showed that the phosphate solubilization by A. pullulans F4 varied with phosphorus sources, which decreased in order of aluminum phosphate > ferric phosphate, calcium phosphate > rock phosphate. The amounts of dissolved phosphorus in the different treatments were all higher than 200 mg x L(-1). The pH of the medium dropped immediately in 48 h, and the aluminum phosphate and ferric phosphate treatments showed a greater decrease in pH than the calcium phosphate and rock phosphate treatments. The organic acid synthesized by A. pullulans F4 included oxalic acid, citric acid and tartaric acid, and oxalic acid, among which oxalic acid was the dominated component. The phosphate dissolving capacity of A. pullulans F4 showed no significant correlation with organic acid, but significantly correlated with the pH. The available phosphorus was significantly improved with the combined application of A. pullulans F4 and glucose, suggesting A. pullulans F4 was a potent candidate for remediation of copper mine wastelands.

Hanford phosphate precipitation filtration process evaluation

International Nuclear Information System (INIS)

Walker, B.W.; McCabe, D.J.

1997-01-01

The purpose of this filter study was to evaluate cross-flow filtration as effective solid-liquid separation technology for treating Hanford wastes, outline operating conditions for equipment, examine the expected filter flow rates, and determine proper cleaning. A proposed Hanford waste pre-treatment process uses sodium hydroxide at high temperature to remove aluminum from sludge. This process also dissolves phosphates. Upon cooling to 40 degrees centigrade the phosphates form a Na7(PO4)2F9H2O precipitate which must be removed prior to further treatment. Filter studies were conducted with a phosphate slurry simulant to evaluate whether 0.5 micron cross-flow sintered metal Mott filters can separate the phosphate precipitate from the wash solutions. The simulant was recirculated through the filters at room temperature and filtration performance data was collected

Biosynthesis and characterization of layered iron phosphate

International Nuclear Information System (INIS)

Zhou Weijia; He Wen; Wang Meiting; Zhang Xudong; Yan Shunpu; Tian Xiuying; Sun Xianan; Han Xiuxiu; Li Peng

2008-01-01

Layered iron phosphate with uniform morphology has been synthesized by a precipitation method with yeast cells as a biosurfactant. The yeast cells are used to regulate the nucleation and growth of layered iron phosphate. The uniform layered structure is characterized by small-angle x-ray diffraction (SAXD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses. Fourier transform infrared spectroscopy (FT-IR) is used to analyze the chemical bond linkages in organic–inorganic hybrid iron phosphate. The likely synthetic mechanism of nucleation and oriented growth is discussed. The electrical conductivity of hybrid iron phosphate heat-treated at different temperatures is presented

Sorption of cesium on titanium and zirconium phosphates

International Nuclear Information System (INIS)

Lebedev, V.N.; Mel'nik, N.A.; Rudenko, A.V.

2003-01-01

Titanium and zirconium phosphates were prepared from mineral raw materials of the Kola Peninsula. Their capability to recover cesium cations from the model solutions and liquid radioactive waste (LRW) was studied. Titanium phosphate prepared from solutions formed by titanite breakdown demonstrates greater distribution coefficients of cesium as compared to zirconium phosphate. Titanium phosphate as a cheaper agent featuring greater sorption capacity was recommended for treatment of LRW to remove cesium [ru

Synergistic solvent extraction investigation of Am (III), Eu (III), Zn(II), and Cs(I), using 2-heptyl-2-methyl-nonanoic acid mixed with different organophosphorus compounds from nitrate media. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

El-Naggar, H A; Ramadan, A; Abdel-Fattah, A [Nuclear Chemistry Department, Hot Laboratories Center, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Extraction studies for investigating the effect of mixing 2-heptyl-2-methyl nonanoic acid (HA) with a number of organophosphorus compounds; namely tributyl phosphate (TBP), terphenyl phosphate oxide (TPPO); tri octyl phosphine oxide (TOPO) or bis-2-(ethyl hexyl) phosphoric acid (HDEHP) in benzene on the extraction of trace elements Am(III), Eu(III), Zn(II), and Cs(I) from nitrate media of ionic strength, I=0.1 M were carried out. The effect of adding different organophosphorus compounds to HA was tested to account for the presence or absence of the phenomenon of synergism. It was found that TBP, TPPO, and TOPO causing some antagonistic effects for the elements studied. Extraction enhancement was only observed with bis- (2-ethyl-hexyl) -phosphoric acid (HDEHP) for all the elements investigated. The extraction mechanisms as well as the thermodynamic parameters for the mixed extracted species are discussed. 19 figs.

Synergistic solvent extraction investigation of Am (III), Eu (III), Zn(II), and Cs(I), using 2-heptyl-2-methyl-nonanoic acid mixed with different organophosphorus compounds from nitrate media. Vol. 3

International Nuclear Information System (INIS)

El-Naggar, H.A.; Ramadan, A.; Abdel-Fattah, A.

1996-01-01

Extraction studies for investigating the effect of mixing 2-heptyl-2-methyl nonanoic acid (HA) with a number of organophosphorus compounds; namely tributyl phosphate (TBP), terphenyl phosphate oxide (TPPO); tri octyl phosphine oxide (TOPO) or bis-2-(ethyl hexyl) phosphoric acid (HDEHP) in benzene on the extraction of trace elements Am(III), Eu(III), Zn(II), and Cs(I) from nitrate media of ionic strength, I=0.1 M were carried out. The effect of adding different organophosphorus compounds to HA was tested to account for the presence or absence of the phenomenon of synergism. It was found that TBP, TPPO, and TOPO causing some antagonistic effects for the elements studied. Extraction enhancement was only observed with bis- (2-ethyl-hexyl) -phosphoric acid (HDEHP) for all the elements investigated. The extraction mechanisms as well as the thermodynamic parameters for the mixed extracted species are discussed. 19 figs

Method of decomposing treatment for radioactive organic phosphate wastes

International Nuclear Information System (INIS)

Uki, Kazuo; Ichihashi, Toshio; Hasegawa, Akira; Sato, Tatsuaki

1985-01-01

Purpose: To decompose the organic phosphoric-acid ester wastes containing radioactive material, which is produced from spent fuel reprocessing facilities, into inorganic materials using a simple device, under moderate conditions and at high decomposing ratio. Method: Radioactive organic phosphate wates are oxidatively decomposed by H 2 O 2 in an aqueous phosphoric-acid solution of metal phosphate salts. Copper phosphates are used as the metal phosphate salts and the decomposed solution of the radioactive organic phosphate wastes is used as the aqueous solution of the copper phosphate. The temperature used for the oxidizing decomposition ranges from 80 to 100 0 C. (Ikeda, J.)

Monte Carlo Simulations of Phosphate Polyhedron Connectivity in Glasses

Energy Technology Data Exchange (ETDEWEB)

ALAM,TODD M.

1999-12-21

Monte Carlo simulations of phosphate tetrahedron connectivity distributions in alkali and alkaline earth phosphate glasses are reported. By utilizing a discrete bond model, the distribution of next-nearest neighbor connectivities between phosphate polyhedron for random, alternating and clustering bonding scenarios was evaluated as a function of the relative bond energy difference. The simulated distributions are compared to experimentally observed connectivities reported for solid-state two-dimensional exchange and double-quantum NMR experiments of phosphate glasses. These Monte Carlo simulations demonstrate that the polyhedron connectivity is best described by a random distribution in lithium phosphate and calcium phosphate glasses.

The effect of different phosphate ion concentrations and ph of the phosphate buffer on lipase bioproduction by rhizopus oligosporus

International Nuclear Information System (INIS)

Haq, I.; Ali, S.; Awan, U.F.; Javed, W.; Mirza, S.

2005-01-01

In the present investigation, we report the effect of phosphate ion concentration and different ph of the phosphate buffer (as diluent) on lipase bioproduction by Rhizopus oligosporus. For this purpose, solid state fermentation was employed. Different agricultural by-products such as wheat bran, rice husk, almond meal, soybean meal and sunflower meal were used as substrate. The maximum lipase activity (72.60 U/g) was observed with the almond meal. Addition of phosphate ions (K/sub 2/HPO/sub 4/) influenced the lipase production. The ph of the phosphate buffer (7.0) was found to be effective for higher yield of lipase. (author)

Preparation of the pur uranium-metal; La preparation de l'uranium-metal pur

Energy Technology Data Exchange (ETDEWEB)

Goldschmidt, B.; Vertes, P. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

A detailed description of the chemical processes used to prepare in the factory of Bouchet of the CEA (Seine-Et-Oise) pur metal uranium with either relatively rich ores, or extracts coming of physical or chemical treatment of poor ores. The nitric treatment of ores succeeds to the production of uranate of impure sodium carbonate. This last last product is dissolved in nitric acid and the uranyl nitrate is extracted by tributyl-phosphate diluted in an inert solvent. The uranyl nitrate pure is re-extracted and successively transformed in uranium peroxide, in orange oxide then in brown oxide which is transformed in fluoride by the anhydrous hydrofluoric acid. Uranate fluoride is then reduced in metal by the pure calcium with an yield superior to 99%. (authors) [French] Description detaillee des procedes chimiques mis en jeu pour preparer a l'Usine du Bouchet du Commissariat a l'Energie Atomique (Seine-et-Oise) l'uranium metal pur a partir soit de minerais relativement riches, soit de concentres provenant de traitement physique ou chimique de minerais pauvres. Le traitement nitrique des minerais aboutit a la production d'uranate de soude impur. Ce dernier est a son tour dissous dans l'acide nitrique et le nitrate d'uranyle est extrait par du tributyl-phosphate dilue par un solvant inerte. Le nitrate d'uranyle pur reextrait est transforme successivement en peroxyde d'uranium, en oxyde orange puis en oxyde brun qui est transforme en fluorure par l'acide fluorhydrique anhydre. Le fluorure uraneux est reduit en metal par le calcium pur avec un rendement superieur a 99 %. (auteurs)

The EIS investigation of powder polyester coatings on phosphated low carbon steel: The effect of NaNO2 in the phosphating bath

International Nuclear Information System (INIS)

Jegdic, B.V.; Bajat, J.B.; Popic, J.P.; Stevanovic, S.I.; Miskovic-Stankovic, V.B.

2011-01-01

Highlights: → The effect of NaNO 2 on surface morphology of iron-phosphate coatings were determined. → Better corrosion stability of polyester coating on phosphated steel without NaNO 2 . → EIS results and microscopic examinations correlate well with adhesion measurements. - Abstract: The effect of different type of iron-phosphate coatings on corrosion stability and adhesion characteristic of top powder polyester coating on steel was investigated. Iron-phosphate coatings were deposited on steel in the novel phosphating bath with or without NaNO 2 as an accelerator. The corrosion stability of the powder polyester coating was evaluated by electrochemical impedance spectroscopy (EIS), adhesion by pull-off and NMP test, while surface morphology of phosphate coatings were investigated by atomic force microscopy (AFM). The adhesion and corrosion stability of powder polyester coatings were improved with pretreatment based on iron-phosphate coating deposited from NaNO 2 -free bath.

Radiological impact of use of phosphate fertilizers

International Nuclear Information System (INIS)

Shukla, V.K.; Chinnaesakki, S.; Sartandel, S.J.; Shanbhag, A.A.; Puranik, V.D.

2003-01-01

The paper describes the results of gamma spectrometric measurements of 238 U, 233 Th, 226 Ra and 40 K in rock phosphates and various types of phosphate fertilizers and by-products. The increase in soil natural radioactivity has been assessed for major Indian crops. No significant increase in soil natural radioactivity is expected due to the application of phosphate fertilizers for agricultural productions. (author)

Exploring plant factors for increasing phosphorus utilization from rock phosphates and native soil phosphates in acidic soils

International Nuclear Information System (INIS)

Feng Guanglin; Xiong Liming

2002-01-01

Six plant species with contrasting capacity in utilizing rock phosphates were compared with regard to their responses to phosphorus starvation in hydroponic cultures. Radish, buckwheat and oil rapeseed are known to have strong ability to use rock phosphates while ryegrass, wheat and sesbania are less efficient. Whereas other plants acidified their culture solution under P starvation (-P), radish plants make alkaline the solution. When neutralizing the pH of the solutions cultured with plants under either -P or + P conditions, solutions with P starved buckwheat, rapeseed, and radish had a higher ability to solubilize Al and Fe phosphates than did those cultured with sesbania, ryegrass and wheat. Characterization of organic ligands in the solutions identified that citrate and malate were the major organic anions exuded by rapeseed and radish. Besides citrate and malate, buckwheat exuded a large amount of tartrate under P starvation. In contrast, ryegrass, wheat and sesbania secreted only a limited amount of oxalic acid, regardless of P status. Changes in activities of phosphoenolpyruvate carboxylase, acid phosphatase, and nitrate reductase in these plants were also compared under P- sufficient or -deficient conditions. The results indicated that plant ability to use rock phosphates or soil phosphates is closely related to their responses toward P starvation. The diversity of P starvation responses was discussed in the context of co-evolution between plants and their environment. Approaches to use plant factors to enhance the effectiveness of rock phosphates were also discussed. (author)

The phosphate balance : current developments and future outlook

NARCIS (Netherlands)

Enk, van R.J.; Vee, van der G.; Acera, L.K.; Schuiling, R.; Ehlert, P.A.I.

2011-01-01

Phosphate is essential for agricultural production and therefore plays a key role in the global production of food and biofuels. There are no agricultural alternatives for phosphate, and a substantial fraction of our annual phosphate consumption is dispersed into the environment where it is largely

The phosphate balance : Current developments and future outlook

NARCIS (Netherlands)

Enk, R.J. van; Acera, L.K.; Schuiling, R.D.; Ehlert, P.; de Wilt, J.G.; van Haren, R.J.F.

2011-01-01

Phosphate is essential for agricultural production and therefore plays a key role in the global production of food and biofuels. There are no agricultural alternatives for phosphate, and a substantial fraction of our annual phosphate consumption is dispersed into the environment where it is largely

Experimental Analysis on Shrinkage and Swelling in Ordinary Concrete

Directory of Open Access Journals (Sweden)

Barbara Kucharczyková

2017-01-01

Full Text Available The paper deals with the experimental determination of shrinkage development during concrete ageing. Three concrete mixtures were made. They differed in the amount of cement in the fresh mixture, 300, 350, and 400 kg/m3. In order to determine the influence of plasticiser on the progress of volume changes, another three concrete mixtures were prepared with plasticiser in the amount of 0.25% by cement mass. Measurements were performed with the goal of observing the influence of cement and plasticiser content on the overall development of volume changes in the concrete. Changes in length and mass losses of the concrete during ageing were measured simultaneously. The continuous measurement of concrete mass losses caused by drying of the specimen’s surface proved useful during the interpretation of results obtained from the concrete shrinkage measurement. During the first 24 hours of ageing, all the concrete mixtures exhibited swelling. Its magnitude and progress were influenced by cement, water, and plasticiser content. However, a loss of mass caused by water evaporation from the surface of the specimens was also recorded in this stage. The measured progress of shrinkage corresponded well to the progress of mass loss.

Radiological impacts of uranium recovery in the phosphate industry

International Nuclear Information System (INIS)

Ryan, M.T.

1981-01-01

This article characterizes the occupational and public radiological health impacts associated with phosphate mining and milling. These impacts are related to the phosphate industry's uranium production potential and are compared with those associated with conventional uranium mining and milling. The radiological impacts resulting from occupational and nonoccupational exposures are assessed. Occupational exposures in phosphate facilities are compared to background exposures and radiological population dose assessments, which characterize important radionuclides and exposure pathways. The following conclusions were reached: (1) public consequences of phosphate mining will occur whether or not uranium is recovered as a by-product, (2) radiological consequences of phosphate mining may be comparable to those associated with uranium mining and milling per unit uranium production, (3) radiological impacts via surface waterways and crops fertilized with uranium-bearing phosphates are of minor consequence, and (4) major radiological public health problems associated with phosphate mining are related to radon and radon progeny exposures in structures built on reclaimed lands or with phosphate mining residues, although the magnitudes of these impacts are difficult to evaluate with current data

Separation process of zirconium and hafnium

International Nuclear Information System (INIS)

Hure, J.; Saint-James, R.

1955-01-01

About the separation different processes of zirconium-hafnium, the extraction by solvent in cross-current is the most easily the process usable on an industrial scale. It uses tributyl phosphate as solvent, diluted with white spirit to facilitate the decanting. Some exploratory tests showed that nitric environment seemed the most favorable for extraction; but a lot of other factors intervene in the separation process. We studied the influence of the acidity successively, the NO 3 - ions concentration, the role of the cation coming with NO 3 - , as well as the influence of the concentration of zirconium in the solution on the separation coefficient β = α Zr / α Hf . (M.B.) [fr

Numerical simulation of extraction behavior of major components in the CMPO-TBP-HNO3 system

International Nuclear Information System (INIS)

Takanashi, M.; Koma, Y.; Koyama, T.; Funasaka, H.

2000-01-01

A numerical simulation code was developed in order to find the optimum condition for separation and the recovery of TRU (TRansUranium) elements in the octyl(phenyl)-N,N-di-isobutyl-carbamoyl-methyl-phosphine oxide (CMPO) - tri-butyl phosphate (TBP) - HNO 3 solvent extraction system. This code is able to predict the extraction behavior of americium and europium in the system containing many components. Calculations of concentration profiles of americium and lanthanides were carried out for a counter current experiment with laboratory scale mixer-settlers. The calculated profiles were in agreement with the experimental ones. The effect of oxalic acid was also included in the calculation and was discussed. (authors)

Investigation into kinetics of redox interaction in the system Ce(4). beta. -diketonate-additional ligand

Energy Technology Data Exchange (ETDEWEB)

Anufrieva, S.I.; Snezhko, N.I.; Pechurova, N.I.; Martynenko, L.N.; Spitsyn, V.I. (Moskovskij Gosudarstvennyj Univ. (USSR))

1981-07-01

The rate of reduction of ..beta..-diketonate complexes of Ce(4) to Ce(3) ..beta..-diketonates in benzene solution in the presence and in the absence of additional ligands is studied using spectrophotometry. The rate of reduction of Ce(4) ..beta..-diketonates increases in the series Ce(TTFA)/sub 4/triphenylphosphine oxide>tributyl phosphate.

The choice of organic diluent for extraction regeneration of NPP spent fuel

International Nuclear Information System (INIS)

Egorov, G.F.; Ilozhev, A.P.; Nikiforov, A.S.; Smelov, V.S.; Shevchenko, V.B.; Shmidt, V.S.

1979-01-01

On the basis of the analysis of the published data the technical requirements for hydrocarbon diluents of tributyl phosphate used in NPP spent fuel process are formulated. The alkane chain length can be in the C 11 - C 15 range. Although the relation of separate alkanes is not strictly defined, it is preferable to use hydrocarbons C 12 - C 13 , which are characterized by the high flash point temperature better compatibility with extracted solvates of nitrates of actinide elements and they have good hydrodynamic parameters. The content of fatty acids and alcohols must not exceed 0.01 mol/l, the content of aromatic hydrocarbons approximately 1 vol. %

Selective solvation extraction of gold from alkaline cyanide solution by alkyl phosphorus esters

Energy Technology Data Exchange (ETDEWEB)

Miller, J.D.; Wan, R.Y.; Mooiman, M.B.; Sibrell, P.L.

1987-01-01

Research efforts have shown that solvation extraction of gold from alkaline cyanide solution is possible by alkyl phosphorus esters. Both tributyl phosphate (TBP) and dibutyl butyl phosphonate (DBBP) appear to be effective extractants for gold and exhibit high loading capacities exceeding 30 gpl. Selective solvation extraction of gold from alkaline cyanide solution can be achieved with selectivity factors relative to other cyanoanions as high as 1000 under certain circumstances. Variables influencing the selectivity such as ionic strength, temperature, and extractant structure, are discussed in terms of the extraction chemistry, which seems to involve the solvation of a M dot, dot, dot Au(CN)2 ion pair.

Waste incineration and immobilization for nuclear facilities. Status report, April-September 1978

International Nuclear Information System (INIS)

Johnson, A.J.; Williams, P.M.; Burkhardt, S.C.; Ledford, J.A.; Gallagher, K.Y.

1980-01-01

The fluidized bed incinerator and waste immobilization processes are being developed to process various liquid and solid wastes that are generated by a nuclear facility. The versatility of the incinerator liquid waste handling system has been enhanced by recent changes made in the pumping and related piping system. Tributyl phosphate-solvent incineration has been evaluated thoroughly using the pilot plant fluidized bed incinerator. Vitrified glass pellets were made to determine operating parameters of a resistance-heated reactor and to produce samples for testing. Procedures were developed for testing the product pellets. A simplified start-up procedure was devised as development continued on a second type of reactor, the Joule-heated melter

Circulation of electrolyte in an electrochemical cell, using Taylor vortices

Energy Technology Data Exchange (ETDEWEB)

Thornton, J D

1990-05-30

In an electrochemical cell for decomposition of organic waste liquids having an anode compartment and a cathode compartment separated by a porous pot, the anode is driven by a shaft having an axial passage extending from an upper inlet in the vicinity of the liquid level to a lower outlet adjacent a turbine. The rotating anode produces Taylor vortices in annular space and liquid is drawn from layer through passage and emerges to contact the anode. In one use, organic solvent such as tributyl phosphate/odourless kerosene is destroyed. Fresh solvent is added through an inlet. A helical cooler may also be provided. (author).

Flame photometric determination of Na, K and Li in uranium compounds

International Nuclear Information System (INIS)

Sabato, S.F.; Lordello, A.R.

1985-01-01

A flame photometric method for the determination of Na, K and Li in uranium compounds is described. The uranium is separated by solvent extraction from hydrochloric acid medium with tri-butyl phosphate. Amounts of uranium in order of 20 μg/ml don't cause any interference in the photometric results. The element Na presents a residual concentration due to the contamination of the reagents. The relative standard deviation is about 10% for the three elements. The relative error varies with the concentration of the element and it is between 1 and 24% for Na, between O and 12% for K and between O and 33% for Li. (Author) [pt

Physico-chemical characterization of Ogun and Sokoto phosphate ...

African Journals Online (AJOL)

Gypsum, calcite and lime were associated with both rock phosphates indicating their liming potential in the soil. ORP was more soluble in water, probably because it ... fertilizers and direct application in crop production. Keywords: Phosphorus, apatite, crop production, fertilizer, Ogun rock phosphate, Sokoto rock phosphate ...

Fourier transform Raman spectroscopy of synthetic and biological calcium phosphates.

Science.gov (United States)

Sauer, G R; Zunic, W B; Durig, J R; Wuthier, R E

1994-05-01

Fourier-transform (FT) Raman spectroscopy was used to characterize the organic and mineral components of biological and synthetic calcium phosphate minerals. Raman spectroscopy provides information on biological minerals that is complimentary to more widely used infrared methodologies as some infrared-inactive vibrational modes are Raman-active. The application of FT-Raman technology has, for the first time, enabled the problems of high sample fluorescence and low signal-to-noise that are inherent in calcified tissues to be overcome. Raman spectra of calcium phosphates are dominated by a very strong band near 960 cm-1 that arises from the symmetric stretching mode (v1) of the phosphate group. Other Raman-active phosphate vibrational bands are seen at approximately 1075 (v3), 590 (v4), and 435 cm-1 (v2). Minerals containing acidic phosphate groups show additional vibrational modes. The different calcium phosphate mineral phases can be distinguished from one another by the relative positions and shapes of these bands in the Raman spectra. FT-Raman spectra of nascent, nonmineralized matrix vesicles (MV) show a distinct absence of the phosphate v1 band even though these structures are rich in calcium and phosphate. Similar results were seen with milk casein and synthetic Ca-phosphatidyl-serine-PO4 complexes. Hence, the phosphate and/or acidic phosphate ions in these noncrystalline biological calcium phosphates is in a molecular environment that differs from that in synthetic amorphous calcium phosphate. In MV, the first distinct mineral phase to form contained acidic phosphate bands similar to those seen in octacalcium phosphate. The mineral phase present in fully mineralized MV was much more apatitic, resembling that found in bones and teeth.(ABSTRACT TRUNCATED AT 250 WORDS)

Phosphate recycling in the phosphorus industry

NARCIS (Netherlands)

Schipper, W.J.; Klapwijk, A.; Potjer, B.; Rulkens, W.H.; Temmink, B.G.; Kiestra, F.D.G.; Lijmbach, A.C.M.

2004-01-01

The article describes the potential and limitations for recovery of phosphate from secondary materials in the production process for white phosphorus. This thermal process involves the feeding of phosphate rock, cokes and pebbles to a furnace. The reducing conditions in the furnace promote the

Standard characterization of phosphate rock samples from the FAO/IAEA phosphate project

International Nuclear Information System (INIS)

Binh, Truong; Zapata, F.

2002-01-01

Phosphate rocks (PR) are phosphate-bearing minerals that vary widely in their inherent characteristics and consequently their agronomic potential. In the framework of a FAO/IAEA networked research project, the evaluation of the agronomic effectiveness of natural and modified PR products under a variety of soil climate and crop management conditions was carried out. The characterization of phosphate rocks is the first and essential step in evaluating their suitability for direct application. If several PR sources are utilized, standardized methods should be used for comparison purposes to determine their agronomic potential. This paper describes the standard characterization of phosphate rock products utilized in the project, in particular the mineralogical and crystallographic analyses, physical analyses, chemical composition and solubility in conventional reagents. A total of 28 phosphate rock samples from 15 countries were collected and analyzed in specialized laboratories. The data on mineralogy, chemical composition and solubility in conventional reagents are closely interrelated. An arbitrary classification of the reactivity of the PR samples was made based on the solubility indices in conventional reagents. On another hand, the results of the crystallographic parameters, calculated indices of absolute solubility, specific surface and porosity reflect the variability of the physical state and the sample pre-conditioning treatment of the analyzed products. A proper characterization of phosphate rock samples should provide the maximum of basic information that can be obtained in a cost-effective manner in normal chemical laboratories. Based on the results of this characterization, the following determinations are recommended: a description of the sample, major elemental (total P, Ca, Mg) composition, solubility in conventional reagents (neutral ammonium citrate, citric and formic acid) and particle size analysis. The classification of PR samples for direct

Radio phosphorus kinetics in the blood of sheep supplemented with dicalcium phosphate, mono ammonium phosphate, triple superphosphate and Tapira rock phosphate

International Nuclear Information System (INIS)

Abdalla, A.L.

1992-01-01

With the aim to study the kinetics of radio phosphorus ( 32 P) in the blood of animals supplemented with dicalcium phosphate (BIC), mono ammonium phosphate (MAP), triple superphosphate (SPT) and Tapira rock phosphate (TAP), 32 male sheep were kept in metabolic cages at the Animal Science Section / CENA - USP. Plasma was obtained by centrifugation and the specific activity, rate of disappearance and half life of 32 P in plasma were determined. In the red blood cells were determined the uptake rate of the radioisotope, the rate of disappearance and half life of 32 P up taken. It was observed a statistical significant difference (p 32 P in the plasma and erythrocytes. The specific activity and half life of 32 P in the plasma were statistically different (p<0,10) among sheep receiving the different phosphorus sources; the same was observed in respect to the red blood cells. It was concluded that the supplemented phosphorus source given in the diet of sheep may affect the kinetics of the radio phosphorus in the blood after been intravenously injected. (author)

Overexpression, crystallization and preliminary X-ray analysis of xylulose-5-phosphate/fructose-6-phosphate phosphoketolase from Bifidobacterium breve

International Nuclear Information System (INIS)

Suzuki, Ryuichiro; Kim, Byung-Jun; Shibata, Tsuyoshi; Iwamoto, Yuki; Katayama, Takane; Ashida, Hisashi; Wakagi, Takayoshi; Shoun, Hirofumi; Fushinobu, Shinya; Yamamoto, Kenji

2010-01-01

Xylulose-5-phosphate/fructose-6-phosphate phosphoketolase from B. breve was overexpressed and crystallized. The crystals belonged to the tetragonal space group I422 and diffracted to beyond 1.7 Å resolution. The xylulose-5-phosphate/fructose-6-phosphate phosphoketolase gene from Bifidobacterium breve was cloned and overexpressed in Escherichia coli. The enzyme was purified to homogeneity and crystallized by the sitting-drop vapour-diffusion method. Crystals were obtained at 293 K using 0.05 mM thiamine diphosphate, 0.25 mM MgCl 2 , 24%(w/v) PEG 6000 and 0.1 M Bicine pH 9.0. The crystals belonged to the tetragonal space group I422, with unit-cell parameters a = b = 174.8, c = 163.8 Å, and diffracted to beyond 1.7 Å resolution

Vanadate influence on metabolism of sugar phosphates in fungus Phycomyces blakesleeanus.

Directory of Open Access Journals (Sweden)

Milan Žižić

Full Text Available The biological and chemical basis of vanadium action in fungi is relatively poorly understood. In the present study, we investigate the influence of vanadate (V5+ on phosphate metabolism of Phycomyces blakesleeanus. Addition of V5+ caused increase of sugar phosphates signal intensities in 31P NMR spectra in vivo. HPLC analysis of mycelial phosphate extracts demonstrated increased concentrations of glucose 6 phosphate, fructose 6 phosphate, fructose 1, 6 phosphate and glucose 1 phosphate after V5+ treatment. Influence of V5+ on the levels of fructose 2, 6 phosphate, glucosamine 6 phosphate and glucose 1, 6 phosphate (HPLC, and polyphosphates, UDPG and ATP (31P NMR was also established. Increase of sugar phosphates content was not observed after addition of vanadyl (V4+, indicating that only vanadate influences its metabolism. Obtained results from in vivo experiments indicate catalytic/inhibitory vanadate action on enzymes involved in reactions of glycolysis and glycogenesis i.e., phosphoglucomutase, phosphofructokinase and glycogen phosphorylase in filamentous fungi.

Issues of natural radioactivity in phosphates

International Nuclear Information System (INIS)

Schnug, E.; Haneklaus, S.; Schnier, C.; Scholten, L.C.

1996-01-01

The fertilization of phosphorus (P) fertilizers is essential in agricultural production, but phosphates contain in dependence on their origin different amounts of trace elements. The problem of cadmium (Cd) loads and other heavy metals is well known. However, only a limited number of investigations examined the contamination of phosphates with the two heaviest metals, uranium (U) and thorium (Th), which are radioactive. Also potassium (K) is lightly radioactive. Measurements are done n the radioactivity content of phosphates, P fertilizers and soils. The radiation doses to workers and public as well as possible contamination of soils from phosphate rock or fertilizer caused by these elements or their daughter products is of interest with regard to radiation protection. The use of P fertilizers is necessary for a sustainable agriculture, but it involves radioactive contamination of soils. The consequences of the use of P fertilizers is discussed, also with regard to existing and proposed legislation. 11 refs., 2 figs., 7 tabs

A phosphate-starvation-inducible outermembrane protein of Pseudomonas fluorescens Ag1 as an immunological phosphate-starvation marker

DEFF Research Database (Denmark)

Leopold, Kristine; Jacobsen, Susanne; Nybroe, Ole

1997-01-01

A phosphate-starvation-inducible outer-membrane protein of Pseudomonas fluorescens Ag1, expressed at phosphate concentrations below0.08-0.13 mM, was purified and characterized. The purification method involved separation of outer-membrane proteins by SDS-PAGE andextraction of the protein from...... nitrocellulose or PVDF membranes after electrotransfer of proteins to the membranes. The N-terminal amino acidsequence of the purified protein, called Psi1, did not show homology to any known proteins, and in contrast to the phosphate-specific porin OprP ofP. aeruginosa its mobility in SDS-PAGE was not affected...

Occurrence of organophosphate flame retardants in drinking water from China.

Science.gov (United States)

Li, Jun; Yu, Nanyang; Zhang, Beibei; Jin, Ling; Li, Meiying; Hu, Mengyang; Zhang, Xiaowei; Wei, Si; Yu, Hongxia

2014-05-01

Several organophosphate flame retardants (OPFRs) have been identified as known or suspected carcinogens or neurotoxic substances. Given the potential health risks of these compounds, we conducted a comprehensive survey of nine OPFRs in drinking water in China. We found total concentrations of OPFRs in tap water ranging from 85.1 ng/L to 325 ng/L, and tris(2-butoxyethyl) phosphate (TBEP), triphenyl phosphate (TPP), and tris(2-chloroisopropyl) phosphate (TCPP) were the most common components. Similar OPFR concentrations and profiles were observed in water samples processed through six different waterworks in Nanjing, China. However, boiling affected OPFR levels in drinking water by either increasing (e.g., TBEP) or decreasing (e.g., tributyl phosphate, TBP) concentrations depending on the particular compound and the state of the indoor environment. We also found that bottled water contained many of the same major OPFR compounds with concentrations 10-25% lower than those in tap water, although TBEP contamination in bottled water remained a concern. Finally, we concluded that the risk of ingesting OPFRs through drinking water was not a major health concern for either adults or children in China. Nevertheless, drinking water ingestion represents an important exposure pathway for OPFRs. Copyright © 2014. Published by Elsevier Ltd.

Isolation of phosphate solubiliser fungi from Araza rhizosphere

International Nuclear Information System (INIS)

Vera, Diana Fernanda; Perez, Hernando; Valencia Hernando

2002-01-01

Araza is an eatable plant, original from the Amazon region, which has been described as a promising species for commercialization (Quevedo 1995). This plant has high productivity even in low content phosphate soil but the presence of phosphate solubilizing microorganisms may contribute to increase this element availability. In this study we report the isolation and characterization of solubilizing fungi processed using the soil washing method, from soil samples were araza is cultivated at two regions in Guaviare, Colombia. Eighteen isolates of fungi capable of solubilizing phosphate were obtained from 2 different sources. The most important species that solubilized phosphate from calcium were Trichoderma aureoviride, Aspergillus aculeatus, Trichoderma strain 1 y Trichoderma strain 2 and for phosphate from iron: Aspergillus oryzae, Paecilomyces strain 3, Gongronella butleri and Fusarium oxysporum

Dielectric aluminium phosphate thin films. Couches minces dielectriques de phosphate d'aluminium

Energy Technology Data Exchange (ETDEWEB)

Daviero, S. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Avinens, C. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Ibanez, A. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Giuntini, J.C. (Lab. Physicochimie des Materiaux Solides, 34 -Montpellier (France)); Philippot, E. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France))

1993-04-01

Aluminium phosphate thin films on silicium substrate have been carried out from tributylphosphate and aluminium acetylacetonate precursors in solution through the ''pyrosol'' process. It can be observed a large range of chemical analysis in terms of experimental conditions. These thin films have been characterized by X-ray diffraction and infrared spectrometry. Their electrical characteristics, defined from direct current and alternative current measurements, are quite different to those of the crystallized phosphate and can be explained by P-O and Al-O ''dangling bond'' existence. (orig.).

Phosphate recycling in the phosphorus industry

NARCIS (Netherlands)

Schipper, W.J.; Klapwijk, A.; Potjer, A.; Rulkens, W.H.; Temmink, B.G.; Kiestra, F.D.G.; Lijmbach, A.C.M.

2001-01-01

The feasibility of phosphate recycling in the white phosphorus production process is discussed. Several types of materials may be recycled, provided they are dry inorganic materials, low in iron, copper and zinc. Sewage sludge ash may be used if no iron is used for phosphate precipitation in the

Application of Potential Phosphate-Solubilizing Bacteria and Organic Acids on Phosphate Solubilization from Phosphate Rock in Aerobic Rice

Directory of Open Access Journals (Sweden)

Qurban Ali Panhwar

2013-01-01

Full Text Available A study was conducted at Universiti Putra Malaysia to determine the effect of phosphate-solubilizing bacteria (PSB and organic acids (oxalic & malic on phosphate (P solubilization from phosphate rock (PR and growth of aerobic rice. Four rates of each organic acid (0, 10, 20, and 30 mM, and PSB strain (Bacillus sp. were applied to aerobic rice. Total bacterial populations, amount of P solubilization, P uptake, soil pH, and root morphology were determined. The results of the study showed significantly high P solubilization in PSB with organic acid treatments. Among the two organic acids, oxalic acid was found more effective compared to malic acid. Application of oxalic acid at 20 mM along with PSB16 significantly increased soluble soil P (28.39 mg kg−1, plant P uptake (0.78 P pot−1, and plant biomass (33.26 mg. Addition of organic acids with PSB and PR had no influence on soil pH during the planting period. A higher bacterial population was found in rhizosphere (8.78 log10 cfu g−1 compared to the nonrhizosphere and endosphere regions. The application of organic acids along with PSB enhanced soluble P in the soil solution, improved root growth, and increased plant biomass of aerobic rice seedlings without affecting soil pH.

Effectiveness and cost-efficiency of phosphate binders in hemodialysis

Directory of Open Access Journals (Sweden)

Zsifkovits, Johannes

2009-06-01

Full Text Available Health political background: In 2006, the prevalence of chronic renal insufficiency in Germany was 91,718, of which 66,508 patients were on dialysis. The tendency is clearly growing. Scientific background: Chronic renal insufficiency results in a disturbance of the mineral balance. It leads to hyperphosphataemia, which is the strongest independent risk factor for mortality in renal patients. Usually, a reduction in the phosphate intake through nutrition and the amount of phosphate filtered out during dialysis are not sufficient to reduce the serum phosphate values to the recommended value. Therefore, phosphate binders are used to bind ingested phosphate in the digestive tract in order to lower the phosphate concentration in the serum. Four different groups of phosphate binders are available: calcium- and aluminium salts are the traditional therapies. Sevelamer and Lanthanum are recent developments on the market. In varying doses, all phosphate binders are able to effectively lower phosphate concentrations. However, drug therapies have achieved recommended phosphate levels in only 50 percent of patients during the last years. Research questions: How effective and efficient are the different phosphate binders in chronic renal insufficient patients? Methods: The systematic literature search yielded 1,251 abstracts. Following a two-part selection process with predefined criteria 18 publications were included in the assessment. Results: All studies evaluated conclude that serum phosphate, serum calcium and intact parathyroid hormone can be controlled effectively with all phosphate binders. Only the number of episodes of hypercalcaemia is higher when using calcium-containing phosphatebinders compared to Sevelamer and Lanthanum. Regarding the mortality rate, the cardiovascular artery calcification and bone metabolism no definite conclusions can be drawn. In any case, the amount of calcification at study start seems to be crucial for the further

Phosphate Framework Electrode Materials for Sodium Ion Batteries.

Science.gov (United States)

Fang, Yongjin; Zhang, Jiexin; Xiao, Lifen; Ai, Xinping; Cao, Yuliang; Yang, Hanxi

2017-05-01

Sodium ion batteries (SIBs) have been considered as a promising alternative for the next generation of electric storage systems due to their similar electrochemistry to Li-ion batteries and the low cost of sodium resources. Exploring appropriate electrode materials with decent electrochemical performance is the key issue for development of sodium ion batteries. Due to the high structural stability, facile reaction mechanism and rich structural diversity, phosphate framework materials have attracted increasing attention as promising electrode materials for sodium ion batteries. Herein, we review the latest advances and progresses in the exploration of phosphate framework materials especially related to single-phosphates, pyrophosphates and mixed-phosphates. We provide the detailed and comprehensive understanding of structure-composition-performance relationship of materials and try to show the advantages and disadvantages of the materials for use in SIBs. In addition, some new perspectives about phosphate framework materials for SIBs are also discussed. Phosphate framework materials will be a competitive and attractive choice for use as electrodes in the next-generation of energy storage devices.

Photoelectron spectroscopy of phosphites and phosphates

Energy Technology Data Exchange (ETDEWEB)

Chattopadhyay, S.; Findley, G.L.; McGlynn, S.P.

1981-01-01

The ultraviolet photoelectron spectra (UPS) of trimethyl and triethyl phosphite, trimethyl and triethyl phosphate and four substituted phosphates are presented. Assignments are based on analogies to the UPS of phosphorus trichloride and phosphoryl trichloride and are substantiated by CNDO/2 computations. The mechanisms of P-O (axial) bond formation is discussed.

Phosphate uptake kinetics for four species of submerged freshwater macrophytes measured by a 33P phosphate radioisotope technique

DEFF Research Database (Denmark)

Christiansen, Nina Høj; Andersen, Frede Østergaard; Jensen, Henning S.

2016-01-01

Phosphate (Pi) uptake kinetics were determined in shoot and root tissues for four freshwater macrophyte species, Littorella uniflora, Potamogeton perfoliatus, Myriophyllum alterniflorum and Elodea canadensis, using a radioactive 33P phosphate technique. Collection of plant material in the oligotr...

The variable charge of andisols as affected by nanoparticles of rock phosphate and phosphate solubilizing bacteria

Science.gov (United States)

Arifin, M.; Nurlaeny, N.; Devnita, R.; Fitriatin, B. N.; Sandrawati, A.; Supriatna, Y.

2018-02-01

Andisols has a great potential as agriculture land, however, it has a high phosphorus retention, variable charge characteristics and high value of zero net charge or pH0. The research is aimed to study the effects of nanoparticles of rock phosphate (NPRP) and biofertilizer (phosphate solubilizing bacteria/PSB) on soil pH, pHo (zero point of charge, ZPC) and organic-C in one subgroup of Andisols, namely Acrudoxic Durudands, Ciater Region West Java. The research was conducted from October 2016 to February 2017 in Soil Physics Laboratory and Laboratory of Soil Chemistry and Fertility, Soil Science Department, Faculty of Agriculture, Universitas Padjadjaran. This experiment used a completely randomized factorial design, consisting of two factors and three replications. The first factor was nanoparticles of rock phosphate consist of 4 doses 0; 25; 50 and 75 g/1 kg soil and the second factor was biofertilizer dose consist of g/1 kg soil and without biofertilizer. Total treatment combinations were 8 with 3 replications, so there were 24 experimental plots. The results showed that in general NPRR and biofertilizer will decrease the value of soil pH throughout the incubation periods. There is an interaction between nanoparticles of rock phosphate and biofertilizer in decreasing pHo in the first month of incubation, but after 4-month incubation period, NPRP increased. Interaction between 75 g nanoparticles of rock phosphate with 1 g biofertilizer/1 kg soil in fourth months of incubation decreased soil organic-C to 3.35%.

Uranium and heavy metals in phosphate fertilizers

International Nuclear Information System (INIS)

Khater, A.E.M.

2008-01-01

Agricultural applications of chemical fertilizers are a worldwide practice. The specific activity of uranium-238 and heavy metals in phosphate fertilizers depends on the phosphate ore from which the fertilizer produced and on the chemical processing of the ore. Composite phosphate fertilizers samples where collected and the uranium-238 specific activity, in Bq/kg, and As, Cd, Cu, Pb, Se concentration, in ppm, were measured. The annual addition of these elements in soil due to fertilization were calculated and discussed. (author)(tk)

Uranium and heavy metals in phosphate fertilizers

International Nuclear Information System (INIS)

Khater, Ashraf E.M.; King Saud University, Riyadh

2008-01-01

Full text: Agricultural applications of chemical fertilizers are a worldwide practice. The specific activity of uranium-238 and heavy metals in phosphate fertilizers depends on the phosphate ore from which the fertilizer produced and on the chemical processing of the ore. Composite phosphate fertilizers samples were collected and the uranium-238 specific activity, in Bq/kg, and As, Cd, Cu, Pb, Se concentration were measured. The annual addition of these elements in soil due to soil fertilization were calculated and discussed. (author)

Availability of native and added phosphates for the soil

International Nuclear Information System (INIS)

Scivittaro, W.B.; Boaretto, A.E.; Muraoka, T.

1995-01-01

In superficial composite samples of two Red-Yellow Latosols with different physical and chemical properties, analyses were carried out on inorganic form of phosphorus as well as the availability of native and added phosphates. The method applied was soil phosphorus fractionation associated with isotopic dilution technique ( 32 P). The samples were taken from pots containing soils incubated for a month with fluid phosphatic fertilizers (phosphoric acid and 10-30-00 suspension) and solid phosphatic fertilizers (mono ammonium phosphate and triple superphosphate), at the rate of 210 mg P 2 O 5 /kg of soil. A control treatment was included. In both soils the availability of inorganic phosphorus fractions decreased at the following order: H 2 O-P > Al-P > Fe-P > CA-P > occluded-P. The water soluble and aluminium phosphates represented the main source of available P for the newly fertilizer, the iron phosphates were also an important source of available phosphorus. The soil phosphorus fixing capacity influenced the availability of native and added phosphates. (author). 17 refs, 3 tabs

Experiences in running solvent extraction plant for thorium compounds [Paper No. : V-5

International Nuclear Information System (INIS)

Gopalkrishnan, C.R.; Bhatt, J.P.; Kelkar, G.K.

1979-01-01

Indian Rare Earths Ltd. operates a Plant using thorium concentrates as raw material, employing hydrocarbonate route, for the manufacture of thorium compounds. A small demonstration solvent extraction plant designed by the Chemical Engineering Division, B.A.R.C. is also being operated for the same purpose using a partly purified thorium hydrocarbonate as raw material. In the solvent extraction process, separation of pure thorium is done in mixer settlers using 40% mixture of tri-butyl phosphate in kerosene. Though a comparatively purer raw material of hydrocarbonate than thorium concentrate is used, heavy muck formation is encountered in the extraction stage. Production of nuclear grade thorium oxide has been successful so far as quality is concerned. The quality of thorium nitrate suffers in the yellow colouration and high phosphate content, the former being only partly controlled through the use of pretreated kerosene. When a larger solvent extraction plant is to be designed to use thorium concentrates as raw material, some of the problems encountered will be considered. (author)

Regularities in Low-Temperature Phosphatization of Silicates

Science.gov (United States)

Savenko, A. V.

2018-01-01

The regularities in low-temperature phosphatization of silicates are defined from long-term experiments on the interaction between different silicate minerals and phosphate-bearing solutions in a wide range of medium acidity. It is shown that the parameters of the reaction of phosphatization of hornblende, orthoclase, and labradorite have the same values as for clayey minerals (kaolinite and montmorillonite). This effect may appear, if phosphotization proceeds, not after silicate minerals with a different structure and composition, but after a secondary silicate phase formed upon interaction between silicates and water and stable in a certain pH range. Variation in the parameters of the reaction of phosphatization at pH ≈ 1.8 is due to the stability of the silicate phase different from that at higher pH values.

Alpha-tocopheryl phosphate: a novel, natural form of vitamin E.

Science.gov (United States)

Gianello, Robert; Libinaki, Roksan; Azzi, Angelo; Gavin, Paul D; Negis, Yesim; Zingg, Jean-Marc; Holt, Phillip; Keah, Hooi-Hong; Griffey, Annike; Smallridge, Andrew; West, Simon M; Ogru, Esra

2005-10-01

We have detected alpha-tocopheryl phosphate in biological tissues including liver and adipose tissue, as well as in a variety of foods, suggesting a ubiquitous presence in animal and plant tissue. Alpha-tocopheryl phosphate is a water-soluble molecule that is resistant to both acid and alkaline hydrolysis, making it undetectable using standard assays for vitamin E. A new method was therefore developed to allow the extraction of both alpha-tocopheryl phosphate and alpha-tocopherol from a single specimen. We used ESMS to detect endogenous alpha-tocopheryl phosphate in biological samples that also contained alpha-tocopherol. Due to the significance of these findings, further proof was required to unequivocally demonstrate the presence of endogenous alpha-tocopheryl phosphate in biological samples. Four independent methods of analysis were examined: HPLC, LCMS, LCMS/MS, and GCMS. Alpha-tocopherol phosphate was identified in all instances by comparison between standard alpha-tocopheryl phosphate and extracts of biological tissues. The results show that alpha-tocopheryl phosphate is a natural form of vitamin E. The discovery of endogenous alpha-tocopheryl phosphate has implications for the expanding knowledge of the roles of alpha-tocopherol in biological systems.

P contribution derived from phosphate solubilizing microorganism activity, rock phosphate and SP-36 determination by isotope "3"2P technique

International Nuclear Information System (INIS)

Anggi Nico Flatian; Iswandi Anas; Atang Sutandi; Ishak

2016-01-01

The "3"2P isotope technique has been used to trace P nutrients in the soil and soil-plant systems. The use of the isotope "3"2P has made it possible to differentiate the P contribution derived from phosphate solubilizing microorganism activity and the fertilizer P in the soil. The aims of the study were to obtain the quantitative data of P contribution derived from phosphate-solubilizing microorganism activity (Aspergillus niger and Burkholderia cepacia), rock phosphate and SP-36 through P uptake by the plants using isotope "3"2P technique and also to study the effects on growth and production of corn plants. The results were showed that phosphate-solubilizing microorganism, rock phosphate and SP-36 was produced specific activity ("3"2P) lower than control. The results were indicated that all treatments could contribute P for the plants. The lower specific activity was caused by supply P from rock phosphate and SP-36, and also was caused by solubilized of unavailable "3"1P from PSM activity, which decreased specific activity on labeled soil. The combination of phosphate-solubilizing microorganism and SP-36 treatments produced the highest P contribution, significantly higher than control and SP-36 only. Phosphate derived from combination of microorganism and SP-36 treatments ranging from 56.06% - 68.54% after 50 days planting, after 35 days planting, 51.96% - 59.65% on stover, 46.33% - 47.70% on grain and 53.02% - 59.87% on corn cob. In addition, the treatments could significantly support the plant growth and yield. It is expressed by increased number of leave at 35 days after planting, dry weight of leave at 35 days after planting and dry weight of grain. (author)

Nano zinc phosphate coatings for enhanced corrosion resistance of mild steel

International Nuclear Information System (INIS)

Tamilselvi, M.; Kamaraj, P.; Arthanareeswari, M.; Devikala, S.

2015-01-01

Highlights: • Nano zinc phosphate coating on mild steel was developed. • Nano zinc phosphate coatings on mild steel showed enhanced corrosion resistance. • The nano ZnO increases the number of nucleating sites for phosphating. • Faster attainment of steady state during nano zinc phosphating. - Abstract: Nano crystalline zinc phosphate coatings were developed on mild steel surface using nano zinc oxide particles. The chemical composition and morphology of the coatings were analyzed by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The particles size of the nano zinc phosphate coating developed was also characterized by TEM analysis. Potentiodynamic polarization and electrochemical impedance studies were carried out in 3.5% NaCl solution. Significant variations in the coating weight, morphology and corrosion resistance were observed as nano ZnO concentrations were varied from 0.25 to 2 g/L in the phosphating baths. The results showed that nano ZnO particles in the phosphating solution yielded phosphate coatings of higher coating weight, greater surface coverage and enhanced corrosion resistance than the normal zinc phosphate coatings (developed using normal ZnO particles in the phosphating baths). Better corrosion resistance was observed for coatings derived from phosphating bath containing 1.5 g/L nano ZnO. The activation effect brought about by the nano ZnO reduces the amount of accelerator (NaNO 2 ) required for phosphating

Reduction of nucleotides by ionizing radiation: uridine 5' phosphate, and cytidine 3' phosphate

International Nuclear Information System (INIS)

Box, H.C.; Potter, W.R.; Budzinski, E.E.

1974-01-01

Anions formed by the addition of an electron to the uracil base were observed in single crystals of the barium salt of uridine 5' phosphate x irradiated at 4.2 0 K. The hyperfine coupling tensor for the C 6 -H proton was deduced from ENDOR measurements; the principal values are -59.12, -32.92 and -16.24 MHz. Similar measurements were made on single crystals of cytidine 3' phosphate. The principal values for the C 6 -H proton hyperfine coupling in the anion formed on the cytosine base are -59.26, -33.98 and -14.68 MHz. (U.S.)

Magnesium-phosphate-glass cements with ceramic-type properties

Science.gov (United States)

Sugama, T.; Kukacka, L.E.

1982-09-23

Rapid setting magnesium phosphate (Mg glass) cementitious materials consisting of magnesium phosphate cement paste, polyborax and water-saturated aggregate, exhibits rapid setting and high early strength characteristics. The magnesium glass cement is prepared from a cation-leachable powder and a bivalent metallic ion-accepting liquid such as an aqueous solution of diammonium phosphate and ammonium polyphosphate. The cation-leachable powder includes a mixture of two different magnesium oxide powders processed and sized differently which when mixed with the bivalent metallic ion-accepting liquid provides the magnesium glass cement consisting primarily of magnesium ortho phosphate tetrahydrate, with magnesium hydroxide and magnesium ammonium phosphate hexahydrate also present. The polyborax serves as a set-retarder. The resulting magnesium mono- and polyphosphate cements are particularly suitable for use as a cementing matrix in rapid repair systems for deteriorated concrete structures as well as construction materials and surface coatings for fireproof structures.

Magnesium phosphate glass cements with ceramic-type properties

Science.gov (United States)

Sugama, Toshifumi; Kukacka, Lawrence E.

1984-03-13

Rapid setting magnesium phosphate (Mg glass) cementitious materials consisting of magnesium phosphate cement paste, polyborax and water-saturated aggregate exhibiting rapid setting and high early strength characteristics. The magnesium glass cement is prepared from a cation-leachable powder and a bivalent metallic ion-accepting liquid such as an aqueous solution of diammonium phosphate and ammonium polyphosphate. The cation-leachable powder includes a mixture of two different magnesium oxide powders processed and sized differently which when mixed with the bivalent metallic ion-accepting liquid provides the magnesium glass cement consisting primarily of magnesium ortho phosphate tetrahydrate, with magnesium hydroxide and magnesium ammonium phosphate hexahydrate also present. The polyborax serves as a set-retarder. The resulting magnesium mono- and polyphosphate cements are particularly suitable for use as a cementing matrix in rapid repair systems for deteriorated concrete structures as well as construction materials and surface coatings for fireproof structures.

A Phosphate Starvation-Inducible Ribonuclease of Bacillus licheniformis.

Science.gov (United States)

Nguyen, Thanh Trung; Nguyen, Minh Hung; Nguyen, Huy Thuan; Nguyen, Hoang Anh; Le, Thi Hoi; Schweder, Thomas; Jürgen, Britta

2016-08-28

The BLi03719 protein of Bacillus licheniformis DSM13 belongs to the most abundant extracellular proteins under phosphate starvation conditions. In this study, the function of this phosphate starvation inducible protein was determined. An amino-acid sequence analysis of the BLi03719-encoding gene showed a high similarity with genes encoding the barnase of Bacillus amyloliquefaciens FZB42 and binase-like RNase of Bacillus pumilus SARF-032. The comparison of the control strain and a BLi03719-deficient strain revealed a strongly reduced extracellular ribonuclease activity of the mutant. Furthermore, this knockout mutant exhibited delayed growth with yeast RNA as an alternative phosphate and carbon source. These results suggest that BLi03719 is an extracellular ribonuclease expressed in B. licheniformis under phosphate starvation conditions. Finally, a BLi03719 mutant showed an advantageous effect on the overexpression of the heterologous amyE gene under phosphate-limited growth conditions.

Phosphate rock costs, prices and resources interaction.

Science.gov (United States)

Mew, M C

2016-01-15

This article gives the author's views and opinions as someone who has spent his working life analyzing the international phosphate sector as an independent consultant. His career spanned two price hike events in the mid-1970's and in 2008, both of which sparked considerable popular and academic interest concerning adequacy of phosphate rock resources, the impact of rising mining costs and the ability of mankind to feed future populations. An analysis of phosphate rock production costs derived from two major industry studies performed in 1983 and 2013 shows that in nominal terms, global average cash production costs increased by 27% to $38 per tonne fob mine in the 30 year period. In real terms, the global average cost of production has fallen. Despite the lack of upward pressure from increasing costs, phosphate rock market prices have shown two major spikes in the 30 years to 2013, with periods of less volatility in between. These price spike events can be seen to be related to the escalating investment cost required by new mine capacity, and as such can be expected to be repeated in future. As such, phosphate rock price volatility is likely to have more impact on food prices than rising phosphate rock production costs. However, as mining costs rise, recycling of P will also become increasingly driven by economics rather than legislation. Copyright © 2015 Elsevier B.V. All rights reserved.

Metal cation controls phosphate release in the myosin ATPase.

Science.gov (United States)

Ge, Jinghua; Huang, Furong; Nesmelov, Yuri E

2017-11-01

Myosin is an enzyme that utilizes ATP to produce a conformational change generating a force. The kinetics of the myosin reverse recovery stroke depends on the metal cation complexed with ATP. The reverse recovery stroke is slow for MgATP and fast for MnATP. The metal ion coordinates the γ phosphate of ATP in the myosin active site. It is accepted that the reverse recovery stroke is correlated with the phosphate release; therefore, magnesium "holds" phosphate tighter than manganese. Magnesium and manganese are similar ions in terms of their chemical properties and the shell complexation; hence, we propose to use these ions to study the mechanism of the phosphate release. Analysis of octahedral complexes of magnesium and manganese show that the partial charge of magnesium is higher than that of manganese and the slightly larger size of manganese ion makes its ionic potential smaller. We hypothesize that electrostatics play a role in keeping and releasing the abstracted γ phosphate in the active site, and the stronger electric charge of magnesium ion holds γ phosphate tighter. We used stable myosin-nucleotide analog complex and Raman spectroscopy to examine the effect of the metal cation on the relative position of γ phosphate analog in the active site. We found that in the manganese complex, the γ phosphate analog is 0.01 nm further away from ADP than in the magnesium complex. We conclude that the ionic potential of the metal cation plays a role in the retention of the abstracted phosphate. © 2017 The Protein Society.

Cyanotoxins: a poison that frees phosphate.

Science.gov (United States)

Raven, John A

2010-10-12

Autotrophic organisms obtain phosphorus from the environment by secreting alkaline phosphatases that act on esters, resulting in inorganic phosphate that is then taken up. New work shows that the cyanobacterium Aphanizomenon ovalisporum obtains inorganic phosphate by secreting the cyanotoxin cylindrospermopsin, which induces alkaline phosphatase in other phytoplankton species. Copyright © 2010 Elsevier Ltd. All rights reserved.

Phosphate coating on stainless steel 304 sensitized

International Nuclear Information System (INIS)

Cruz V, J. P.; Vite T, J.; Castillo S, M.; Vite T, M.

2009-01-01

The stainless steel 304 can be sensitized when welding processes are applied, that causes the precipitation of chromium carbide in the grain limits, being promoted in this way the formation of galvanic cells and consequently the corrosion process. Using a phosphate coating is possible to retard the physiochemical damages that can to happen in the corrosion process. The stainless steel 304 substrate sensitized it is phosphate to base of Zn-Mn, in a immersion cell very hot. During the process was considered optimization values, for the characterization equipment of X-rays diffraction and scanning electron microscopy was used. The XRD technique confirmed the presence of the phases of manganese phosphate, zinc phosphate, as well as the phase of the stainless steel 304. When increasing the temperature from 60 to 90 C in the immersion process a homogeneous coating is obtained. (Author)

Corrosion inhibition by lithium zinc phosphate pigment

International Nuclear Information System (INIS)

Alibakhshi, E.; Ghasemi, E.; Mahdavian, M.

2013-01-01

Highlights: •Synthesis of lithium zinc phosphate (LZP) by chemical co-precipitation method. •Corrosion inhibition activity of pigments compare with zinc phosphate (ZP). •LZP showed superior corrosion inhibition effect in EIS measurements. •Evaluation of adhesion strength and dispersion stability. -- Abstract: Lithium zinc phosphate (LZP) has been synthesized through a co-precipitation process and characterized by XRD and IR spectroscopy. The inhibitive performances of this pigment for corrosion of mild steel have been discussed in comparison with the zinc phosphate (ZP) in the pigment extract solution by means of EIS and in the epoxy coating by means of salt spray. The EIS and salt spray results revealed the superior corrosion inhibitive effect of LZP compared to ZP. Moreover, adhesion strength and dispersion stability of the pigmented epoxy coating showed the advantage of LZP compared to ZP

Global radiological impact of the phosphate fertilizers

International Nuclear Information System (INIS)

Morales, Rudnei Karam; Alves, Rex Nazare

1996-01-01

About ninety percent of the products obtained in the phosphate industry are directly used in agriculture as fertilizers. The uranium, thorium and radium content in phosphate fertilizers pollute the soil, water and air, creating risks due to associated natural radiation. This work shows the concentration of radionuclides present in various products of the national and American phosphate fertilizers industry, and compared them with worldwide mean values. The radiological impact of the products on the environment is evaluated and suggestions are presented in order to minimize the risks due to radioactivity. (author)

Study of extraction of rare earths by oil sulfoxides and their mixtures with tributyl phosphate

International Nuclear Information System (INIS)

Mikhlin, E.B.; Vol'dman, G.M.; Zelikman, A.N.; Novikova, N.N.

1977-01-01

Neodymium distribution is studied during its extraction from nitrate solutions with oil sulphoxides (OSO) and their mixtures with TBP in a wide range of neodymium and desalting agent (aluminium nitrate) concentrations. The extraction capacity of OSO is shown to considerably exceed that of TBP. A synergic effect due to formation of mixed solvates is observed at extraction with an OSO-TBP mixture. The separation coefficients (β) of the pairs Ce-La, Pr-Ce and Nd-Pr are determined. OSO and, especially, the OSO-TBP mixture are shown to be applicable for separating cerium and lanthanum, since the βsub(Ge/La) value for these extraction agents is higher than that for TBP, the extraction agent capacity attaining values that are acceptable for practival purposes

Determination of tributyl phosphate (TBP) by precision densimetry in the TBP-Varsol-HNO3 system

International Nuclear Information System (INIS)

Matsuda, H.T.; Araujo, B.F. de; Araujo, J.A. de.

1981-05-01

A direct TBP determination by digital density measurements is presented. The method is based on the variation of the natural frequency of a hollow oscillator when filled with a solvent. For this purpose a digital densimeter DMA 02C, from PAAR was used. There is a simple relationship between the density of the sample and the frequency of the filled oscillator. (I.C.R.) [pt

Determination of radioactivity in Chinese phosphate rock and fertilizer

International Nuclear Information System (INIS)

Chen Jingjian; Zhu Yongyi; Yang Juncheng

1993-01-01

The presented paper reported the radioactivity of U-238, Ra-226, Th-232 and K-40 in Chinese phosphate rocks by gamma spectrographic analysis during 1985-1990. The results showed that the decay chain of U-238-Ra-226 was the main source of radionuclides in phosphate rocks. The radionuclides in phosphate fertilizer differed from the forms of phosphate fertilizer. U-238 was the most important radionuclide in phosphoric compound fertilizer. The transfer rate of radionuclides was also estimated. (2 figs., 1 tab.)

Engineering Potato Starch with a Higher Phosphate Content.

Directory of Open Access Journals (Sweden)

Xuan Xu

Full Text Available Phosphate esters are responsible for valuable and unique functionalities of starch for industrial applications. Also in the cell phosphate esters play a role in starch metabolism, which so far has not been well characterized in storage starch. Laforin, a human enzyme composed of a carbohydrate-binding module and a dual-specificity phosphatase domain, is involved in the dephosphorylation of glycogen. To modify phosphate content and better understand starch (dephosphorylation in storage starch, laforin was engineered and introduced into potato (cultivar Kardal. Interestingly, expression of an (engineered laforin in potato resulted in significantly higher phosphate content of starch, and this result was confirmed in amylose-free potato genetic background (amf. Modified starches exhibited altered granule morphology and size compared to the control. About 20-30% of the transgenic lines of each series showed red-staining granules upon incubation with iodine, and contained higher phosphate content than the blue-stained starch granules. Moreover, low amylose content and altered gelatinization properties were observed in these red-stained starches. Principle component and correlation analysis disclosed a complex correlation between starch composition and starch physico-chemical properties. Ultimately, the expression level of endogenous genes involved in starch metabolism was analysed, revealing a compensatory response to the decrease of phosphate content in potato starch. This study provides a new perspective for engineering starch phosphate content in planta by making use of the compensatory mechanism in the plant itself.

Phosphate and Cardiovascular Disease beyond Chronic Kidney Disease and Vascular Calcification

Directory of Open Access Journals (Sweden)

Sinee Disthabanchong

2018-01-01

Full Text Available Phosphate is essential for life but its accumulation can be detrimental. In end-stage renal disease, widespread vascular calcification occurs as a result of chronic phosphate load. The accumulation of phosphate is likely to occur long before the rise in serum phosphate above the normal range since several observational studies in both general population and early-stage CKD patients have identified the relationship between high-normal serum phosphate and adverse cardiovascular outcomes. Consumption of food high in phosphate increases both fasting and postprandial serum phosphate and habitual intake of high phosphate diet is associated with aging, cardiac hypertrophy, endothelial dysfunction, and subclinical atherosclerosis. The decline in renal function and dietary phosphate load can increase circulating fibroblast growth factor-23 (FGF-23 which may have a direct impact on cardiomyocytes. Increased FGF-23 levels in both CKD and general populations are associated with left ventricular hypertrophy, congestive heart failure, atrial fibrillation, and mortality. Increased extracellular phosphate directly affects endothelial cells causing cell apoptosis and vascular smooth muscle cells (VSMCs causing transformation to osteogenic phenotype. Excess of calcium and phosphate in the circulation can promote the formation of protein-mineral complex called calciprotein particles (CPPs. In CKD, these CPPs contain less calcification inhibitors, induce inflammation, and promote VSMC calcification.

An efficient method for qualitative screening of phosphate-solubilizing bacteria.

Science.gov (United States)

Mehta, S; Nautiyal, C S

2001-07-01

An efficient protocol was developed for qualitative screening of phosphate-solubilizing bacteria, based upon visual observation. Our results indicate that, by using our formulation containing bromophenol blue, it is possible to quickly screen on a qualitative basis the phosphate-solubilizing bacteria. Qualitative analysis of the phosphate solubilized by various groups correlated well with grouping based upon quantitative analysis of bacteria isolated from soil, effect of carbon, nitrogen, salts, and phosphate solubilization-defective transposon mutants. However, unlike quantitative analysis methods that involve time-consuming biochemical procedures, the time for screening phosphate-solubilizing bacteria is significantly reduced by using our simple protocol. Therefore, it is envisaged that usage of this formulation based upon qualitative analysis will be salutary for the quick screening of phosphate-solubilizing bacteria. Our results indicate that the formulation can also be used as a quality control test for expeditiously screening the commercial bioinoculant preparations, based on phosphate solubilizers.

Influence of protonation or alkylation of the phosphate group on the e. s. r. spectra and on the rate of phosphate elimination from 2-methoxyethyl phosphate 2-yl radicals. [. gamma. rays

Energy Technology Data Exchange (ETDEWEB)

Behrens, G; Koltzenburg, G; Ritter, A; Schulte-Frohlinde, D [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany, F.R.). Inst. fuer Strahlenchemie

1978-02-01

The e.s.r. spectra of l-yl, 2-yl and 3'-yl methoxethyl phosphate radicals derived from CH/sub 3/OCH/sub 2/CH/sub 2/-OPO/sub 3/H/sub 2/ by hydrogen abstraction have been measured in aqueous solutions and the hyperfine constants determined. The coupling constants vary strongly with protonation or alkylation of the phosphate group. The 2-yl radicals eliminate phosphate. The rate-constants for the elimination (ksub(e)) have been estimated by e.s.r. measurements and by product studies as a function of pH using /sup 60/Co ..gamma..-radiolysis. The ksub(e) values vary from approximately 0.3 s/sup -1/ for the CH/sub 3/OCHCH/sub 2/OPO/sub 3//sup - -/ radical and approximately 10/sup 3/s/sup -1/ for CH/sub 3/OCHCH/sub 2/OPO/sub 3/H/sup -/, to approximately 3 x 10/sup 6/s/sup -1/ for CH/sub 3/OCHCH/sub 2/OPO/sub 3/H/sub 2/. Alkylation of the phosphate group increased the elimination rate-constant to a similar extent as protonation. The results support a recent mechanism which described the OH-radical-induced single-strand breaks of DNA in aqueous solution starting from the C-4' radical of the sugar moiety. It is further concluded the C-4' radical of DNA eliminates the 3'-phosphate group faster than the 5'-phosphate group.

Final Report - Assessment of Potential Phosphate Ion-Cementitious Materials Interactions

International Nuclear Information System (INIS)

Naus, Dan J.; Mattus, Catherine H.; Dole, Leslie Robert

2007-01-01

The objectives of this limited study were to: (1) review the potential for degradation of cementitious materials due to exposure to high concentrations of phosphate ions; (2) provide an improved understanding of any significant factors that may lead to a requirement to establish exposure limits for concrete structures exposed to soils or ground waters containing high levels of phosphate ions; (3) recommend, as appropriate, whether a limitation on phosphate ion concentration in soils or ground water is required to avoid degradation of concrete structures; and (4) provide a 'primer' on factors that can affect the durability of concrete materials and structures in nuclear power plants. An assessment of the potential effects of phosphate ions on cementitious materials was made through a review of the literature, contacts with concrete research personnel, and conduct of a 'bench-scale' laboratory investigation. Results of these activities indicate that: no harmful interactions occur between phosphates and cementitious materials unless phosphates are present in the form of phosphoric acid; phosphates have been incorporated into concrete as set retarders, and phosphate cements have been used for infrastructure repair; no standards or guidelines exist pertaining to applications of reinforced concrete structures in high-phosphate environments; interactions of phosphate ions and cementitious materials has not been a concern of the research community; and laboratory results indicate similar performance of specimens cured in phosphate solutions and those cured in a calcium hydroxide solution after exposure periods of up to eighteen months. Relative to the 'primer,' a separate NUREG report has been prepared that provides a review of pertinent factors that can affect the durability of nuclear power plant reinforced concrete structures

Final Report - Assessment of Potential Phosphate Ion-Cementitious Materials Interactions

Energy Technology Data Exchange (ETDEWEB)

Naus, Dan J [ORNL; Mattus, Catherine H [ORNL; Dole, Leslie Robert [ORNL

2007-06-01

The objectives of this limited study were to: (1) review the potential for degradation of cementitious materials due to exposure to high concentrations of phosphate ions; (2) provide an improved understanding of any significant factors that may lead to a requirement to establish exposure limits for concrete structures exposed to soils or ground waters containing high levels of phosphate ions; (3) recommend, as appropriate, whether a limitation on phosphate ion concentration in soils or ground water is required to avoid degradation of concrete structures; and (4) provide a "primer" on factors that can affect the durability of concrete materials and structures in nuclear power plants. An assessment of the potential effects of phosphate ions on cementitious materials was made through a review of the literature, contacts with concrete research personnel, and conduct of a "bench-scale" laboratory investigation. Results of these activities indicate that: no harmful interactions occur between phosphates and cementitious materials unless phosphates are present in the form of phosphoric acid; phosphates have been incorporated into concrete as set retarders, and phosphate cements have been used for infrastructure repair; no standards or guidelines exist pertaining to applications of reinforced concrete structures in high-phosphate environments; interactions of phosphate ions and cementitious materials has not been a concern of the research community; and laboratory results indicate similar performance of specimens cured in phosphate solutions and those cured in a calcium hydroxide solution after exposure periods of up to eighteen months. Relative to the "primer," a separate NUREG report has been prepared that provides a review of pertinent factors that can affect the durability of nuclear power plant reinforced concrete structures.

Serum phosphate and cognitive function in older men.

Science.gov (United States)

Slinin, Yelena; Vo, Tien; Taylor, Brent C; Murray, Anne M; Schousboe, John; Langsetmo, Lisa; Ensrud, Kristine

2018-01-01

Determine whether serum phosphate is associated with concurrent cognitive impairment and subsequent cognitive decline in older men independent of demographic covariates and atherosclerotic risk factors. In a prospective study of 5529 men enrolled in the Osteoporotic Fractures in Men study, we measured baseline serum phosphate, baseline cognitive function, and change in cognitive function between baseline and follow-up exams an average of 4.6 years later using the Modified Mini-Mental State (3MS) Examination and Trails B. There was no association between serum phosphate and odds of cognitive impairment as assessed by baseline 3MS score or risk of cognitive decline as assessed by longitudinal change in 3MS score. Higher baseline serum phosphate was associated with higher odds of poor executive function as assessed by Trails B with fully adjusted odds ratios 1.12 (95% confidence interval: 0.83-1.52), 1.31 (0.97-1.77), and 1.45 (1.08-1.94) for men in the second, third, and fourth versus the bottom quartile (referent group) of serum phosphate (p-trend 0.007). However, higher phosphate level was not associated with risk of decline in executive function as assessed by longitudinal change in Trails B score with fully adjusted odds ratios 0.94 (95% confidence interval 0.69-1.28), 0.96 (0.70-1.32), and 1.21 (0.89-1.66) for men in the second, third, and fourth versus the bottom quartile (referent group) of serum phosphate (p-trend 0.22). Higher serum phosphate in older men was associated with a higher likelihood of poor executive function, but not with impaired global cognitive function or decline in executive or global cognition. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

EFFECT OF SODIUM PHOSPHATES ON SELECTED FOOD GRADE BACTERIA

Directory of Open Access Journals (Sweden)

Stanislav Kráčmar

2011-04-01

Full Text Available The aim of this study was to examine the inhibitory effect in vitro of selected sodium phosphates (under the corporate names Hexa 68, Hexa 70, Trikrystal, FST, Pyro 52, KPS, Didi on selected gram-positive and gram-negative bacteria. Seven different concentrations of each phosphate were used. Sensitivity of the bacterial strains to phosphates was observed in broth supplemented with salts. In vitro was showed a negative effect of various phosphates on growth of selected gram-positive bacteria. Orthophosphates and diphosphates (pyrophosphates did not have significant inhibitory effect on tested bacteria at neutral pH. With the exception of phosphate Trikrystal has not been found in vitro significant inhibitory effects on gram-negative bacteria.doi:10.5219/141

Reagentless phosphate ion sensor system for environmental monitoring

Energy Technology Data Exchange (ETDEWEB)

Suzuki, M.; Kurata, H.; Inoue, Y.; Shin, H. [Kyushu Institute of Technology, Fukuoka (Japan). Faculty of computer Science and Systems; Kubo, I. [Soka University, Tokyo (Japan). Faculty of Engineering; Nakamura, H.; Ikebukuro, K.; Karube, I. [The University of Tokyo, Tokyo (Japan). Research Center for Advanced Science and Technology

1998-06-05

Phosphate ion sensor system using an electrochemical detector was developed by the use of recombinant pyruvate oxidase (PyOD) from Lactobacillus plantarum, which needs no addition of thiamine pyrophosphate and flavin adenine dinucleotide for reaction. This system could detect 2 nM hydrogen peroxide. Response time for phosphate ion was 80 s and total measurement time for one sample was 3 min. Citrate buffer solution (pH 6.3) was most suitable for the measurement and optimum flow rate was 0.6 ml/min. Under these optimum conditions minimum detection limit of phosphate ion was 15 nM, which was enough for the determination of phosphate ion in dam-lake. 6 refs., 5 figs., 1 tab.

Thermo-tolerant phosphate-solubilizing microbes for multi-functional biofertilizer preparation.

Science.gov (United States)

Chang, Cheng-Hsiung; Yang, Shang-Shyng

2009-02-01

In order to prepare the multi-functional biofertilizer, thermo-tolerant phosphate-solubilizing microbes including bacteria, actinomycetes, and fungi were isolated from different compost plants and biofertilizers. Except Streptomycesthermophilus J57 which lacked pectinase, all isolates possessed amylase, CMCase, chitinase, pectinase, protease, lipase, and nitrogenase activities. All isolates could solubilize calcium phosphate and Israel rock phosphate; various isolates could solubilize aluminum phosphate, iron phosphate, and hydroxyapatite. During composting, biofertilizers inoculated with the tested microbes had a significantly higher temperature, ash content, pH, total nitrogen, soluble phosphorus content, and germination rate than non-inoculated biofertilizer; total organic carbon and carbon-to-nitrogen ratio showed the opposite pattern. Adding these microbes can shorten the period of maturity, improve the quality, increase the soluble phosphorus content, and enhance the populations of phosphate-solubilizing and proteolytic microbes in biofertilizers. Therefore, inoculating thermo-tolerant phosphate-solubilizing microbes into agricultural and animal wastes represents a practical strategy for preparing multi-functional biofertilizer.

An unexpected phosphate binding site in Glyceraldehyde 3-Phosphate Dehydrogenase: Crystal structures of apo, holo and ternary complex of Cryptosporidium parvum enzyme

Energy Technology Data Exchange (ETDEWEB)

Cook, William J; Senkovich, Olga; Chattopadhyay, Debasish; (UAB)

2009-06-08

The structure, function and reaction mechanism of glyceraldehyde 3-phosphate dehydrogenase (GAPDH) have been extensively studied. Based on these studies, three anion binding sites have been identified, one 'Ps' site (for binding the C-3 phosphate of the substrate) and two sites, 'Pi' and 'new Pi', for inorganic phosphate. According to the original flip-flop model, the substrate phosphate group switches from the 'Pi' to the 'Ps' site during the multistep reaction. In light of the discovery of the 'new Pi' site, a modified flip-flop mechanism, in which the C-3 phosphate of the substrate binds to the 'new Pi' site and flips to the 'Ps' site before the hydride transfer, was proposed. An alternative model based on a number of structures of B. stearothermophilus GAPDH ternary complexes (non-covalent and thioacyl intermediate) proposes that in the ternary Michaelis complex the C-3 phosphate binds to the 'Ps' site and flips from the 'Ps' to the 'new Pi' site during or after the redox step. We determined the crystal structure of Cryptosporidium parvum GAPDH in the apo and holo (enzyme + NAD) state and the structure of the ternary enzyme-cofactor-substrate complex using an active site mutant enzyme. The C. parvum GAPDH complex was prepared by pre-incubating the enzyme with substrate and cofactor, thereby allowing free movement of the protein structure and substrate molecules during their initial encounter. Sulfate and phosphate ions were excluded from purification and crystallization steps. The quality of the electron density map at 2{angstrom} resolution allowed unambiguous positioning of the substrate. In three subunits of the homotetramer the C-3 phosphate group of the non-covalently bound substrate is in the 'new Pi' site. A concomitant movement of the phosphate binding loop is observed in these three subunits. In the fourth subunit the C-3 phosphate

An unexpected phosphate binding site in Glyceraldehyde 3-Phosphate Dehydrogenase: Crystal structures of apo, holo and ternary complex of Cryptosporidium parvum enzyme

Directory of Open Access Journals (Sweden)

Chattopadhyay Debasish

2009-02-01

Full Text Available Abstract Background The structure, function and reaction mechanism of glyceraldehyde 3-phosphate dehydrogenase (GAPDH have been extensively studied. Based on these studies, three anion binding sites have been identified, one 'Ps' site (for binding the C-3 phosphate of the substrate and two sites, 'Pi' and 'new Pi', for inorganic phosphate. According to the original flip-flop model, the substrate phosphate group switches from the 'Pi' to the 'Ps' site during the multistep reaction. In light of the discovery of the 'new Pi' site, a modified flip-flop mechanism, in which the C-3 phosphate of the substrate binds to the 'new Pi' site and flips to the 'Ps' site before the hydride transfer, was proposed. An alternative model based on a number of structures of B. stearothermophilus GAPDH ternary complexes (non-covalent and thioacyl intermediate proposes that in the ternary Michaelis complex the C-3 phosphate binds to the 'Ps' site and flips from the 'Ps' to the 'new Pi' site during or after the redox step. Results We determined the crystal structure of Cryptosporidium parvum GAPDH in the apo and holo (enzyme + NAD state and the structure of the ternary enzyme-cofactor-substrate complex using an active site mutant enzyme. The C. parvum GAPDH complex was prepared by pre-incubating the enzyme with substrate and cofactor, thereby allowing free movement of the protein structure and substrate molecules during their initial encounter. Sulfate and phosphate ions were excluded from purification and crystallization steps. The quality of the electron density map at 2Å resolution allowed unambiguous positioning of the substrate. In three subunits of the homotetramer the C-3 phosphate group of the non-covalently bound substrate is in the 'new Pi' site. A concomitant movement of the phosphate binding loop is observed in these three subunits. In the fourth subunit the C-3 phosphate occupies an unexpected site not seen before and the phosphate binding loop remains in

Preparation and Characterization of Porous Calcium Phosphate Bioceramics

Institute of Scientific and Technical Information of China (English)

Honglian Dai; Xinyu Wang; Yinchao Han; Xin Jiang; Shipu Li

2011-01-01

β-tricalcium phosphate (β-TCP) powder and Na2O-CaO-MgO-P2O5 glass binder were synthesized and mixed, and then the biodegradable porous calcium phosphate ceramics were successfully prepared by foaming and sintering at 850℃. The as-prepared ceramics possess a high porosity with partial three-dimension interconnected macro- and micro-pores. As in vitro experiment testified, the calcium phosphate ceramics (CPCs) has good degradability.

Fibroblast Growth Factor 23 (FGF23 and Disorders of Phosphate Metabolism

Directory of Open Access Journals (Sweden)

Tasuku Saito

2009-01-01

Full Text Available Derangements in serum phosphate level result in rickets/osteomalacia or ectopic calcification indicating that healthy people without these abnormalities maintain serum phosphate within certain ranges. These results indicate that there must be a regulatory mechanism of serum phosphate level. Fibroblast growth factor 23 (FGF23 was identified as the last member of FGF family. FGF23 is produced by bone and reduces serum phosphate level by suppressing phosphate reabsorption in proximal tubules and intestinal phosphate absorption through lowering 1,25-dihydroxyvitamin D level. It has been shown that excess and deficient actions of FGF23 result in hypophosphatemic rickets/osteomalacia and hyperphosphatemic tumoral calcinosis, respectively. These results indicate that FGF23 works as a hormone, and several disorders of phosphate metabolism can be viewed as endocrine diseases. It may become possible to treat patients with abnormal phosphate metabolism by pharmacologically modifying the activity of FGF23.

Phosphate limitation induces sporulation in the chytridiomycete Blastocladiella emersonii.

Science.gov (United States)

Bongiorno, Vagner Alexandre; Ferreira da Cruz, Angela; Nunis da Silva, Antonio; Corrêa, Luiz Carlos

2012-09-01

The cell cycle is controlled by numerous mechanisms that ensure correct cell division. If growth is not possible, cells may eventually promote autophagy, differentiation, or apoptosis. Microorganisms interrupt their growth and differentiate under general nutrient limitation. We analyzed the effects of phosphate limitation on growth and sporulation in the chytridiomycete Blastocladiella emersonii using kinetic data, phase-contrast, and laser confocal microscopy. Under phosphate limitation, zoospores germinated and subsequently formed 2-4 spores, regardless of the nutritional content of the medium. The removal of phosphate at any time during growth induced sporulation of vegetative cells. If phosphate was later added to the same cultures, growth was restored if the cells were not yet committed to sporulation. The cycles of addition and withdrawal of phosphate from growth medium resulted in cycles of germination-growth, germination-sporulation, or germination-growth-sporulation. These results show that phosphate limitation is sufficient to interrupt cell growth and to induce complete sporulation in B. emersonii. We concluded that the determination of growth or sporulation in this microorganism is linked to phosphate availability when other nutrients are not limiting. This result provides a new tool for the dissection of nutrient-energy and signal pathways in cell growth and differentiation.

A study of the inhibiton of copper corrosion by triethyl phosphate and triphenyl phosphate self-assembled monolayers

Directory of Open Access Journals (Sweden)

HOUYI MA

2006-02-01

Full Text Available Two kinds of phosphates, triethyl phosphate (TEP and triphenyl phosphate (TPP, were used to form self-assembled monolayers for the inhibition of the corrosion of copper in 0.2 mol dm–3 NaCl solution. Electrochemical impedance spectroscopy (EIS was applied to investigate the inhibition effects. The results showed that their inhibition ability first increased with increasing immersion time in ethanolic solutions of the corresponding compounds. However, when the immersion time was increased over some critical point, the inhibition effect decreased. For the same immersion time, the inhibition effect of the TPP monolayer was more pronounced than that of the TEP monolayer. Thus, ab initio calculations were used to interpret the relationship between the inhibition effects and the structures of the compounds.

Lanthanum-modified bentonite: potential for efficient removal of phosphates from fishpond effluents.

Science.gov (United States)

Kurzbaum, Eyal; Raizner, Yasmin; Cohen, Oded; Rubinstein, Guy; Bar Shalom, Oded

2017-06-01

Adsorption has been suggested as an effective method for removing phosphates from agricultural wastewater effluents that contain relatively high phosphate concentrations. The present study focused on the use of a bentonite-lanthanum clay (Phoslock ® ) for reducing the dissolved phosphate concentration in fishpond effluents. Batch experiments with synthetic phosphate-spiked solutions and with fishpond effluents were performed in order to determine adsorption equilibrium isotherms and kinetics as well as to determine the efficiency of Phoslock ® in removing phosphate from these solutions. In the synthetic phosphate-spiked solution, the mean maximum phosphate adsorption capacity was 92 mg Phoslock ® /mg phosphate removal. A ratio of 50, 100, and 200 mg Phoslock ® /mg phosphate removal was found for complete phosphate removal from the fishpond effluents, where higher doses of Phoslock ® led to a faster removal rate (94% removal within the first 150 min). These results show that bentonite-lanthanum clay can be employed for designing a treatment process for efficient phosphate removal from fishpond effluents.

Prevention of radioactive contamination in the manufacture of phosphate fertilizers

International Nuclear Information System (INIS)

Romero G, E.T.

1995-01-01

In this work was studied the separation of uranium from the phosphate rock to decrease the level of radioactivity in the phosphate fertilizers, this prevents the redistribution of uranium in the environment. The uranium leaching conditions from phosphate rock were estimated using alkaline solutions. The changes in the natural phosphate rock after leaching were studied. The amenability to separate the uranium from phosphate rock with ammonium carbonate / bicarbonate solution was determined. The uranium extraction was approximately 40%. The leaching conditions showed high selectivity for uranium without changes in the ore structure. The bulk ore was not dissolved. (Author)

Phosphate removal from digested sludge supernatant using modified fly ash.

Science.gov (United States)

Xu, Ke; Deng, Tong; Liu, Juntan; Peng, Weigong

2012-05-01

The removal of phosphate in digested sludge supernatant by modified coal fly ash was investigated in this study. Modification of the fly ash by the addition of sulfuric acid could significantly enhance its immobilization ability. The experimental results also showed that adsorption of phosphate by the modified fly ash was rapid with the removal percentage of phosphate reaching an equilibrium of 98.62% in less than 5 minutes. The optimum pH for phosphate removal was 9 and the removal percentage increased with increasing adsorbent dosage. The effect of temperature on phosphate removal efficiency was not significant from 20 to 40 degrees C. X-ray diffraction and scanning electron microscope analyses showed that phosphate formed an amorphous precipitate with water-soluble calcium, aluminum, and iron ions in the modified fly ash.

A study of phosphate absorption by magnesium iron hydroxycarbonate.

Science.gov (United States)

Du, Yi; Rees, Nicholas; O'Hare, Dermot

2009-10-21

A study of the mechanism of phosphate adsorption by magnesium iron hydroxycarbonate, [Mg(2.25)Fe(0.75)(OH)(6)](CO(3))(0.37).0.65H(2)O over a range of pH has been carried out. The efficiency of the phosphate removal from aqueous solution has been investigated between pH 3-9 and the resulting solid phases have been studied by elemental analysis, XRD, FT-IR, Raman, HRTEM, EDX and solid-state MAS (31)P NMR. The analytical and spectroscopic data suggest that phosphate removal from solution occurs not by anion intercalation of the relevant phosphorous oxyanion (H(2)PO(4)(-) or HPO(4)(2-)) into the LDH but by the precipitation of either an insoluble iron hydrogen phosphate hydrate and/or a magnesium phosphate hydrate.

Canyon solvent cleaning with solid adsorbents

International Nuclear Information System (INIS)

Reif, D.J.

1987-01-01

The HM Process at the Savannah River Plant (SRP) uses 7.5% tributyl phosphate in n-paraffin as an extraction solvent. During use, the solvent is altered due to hydrolysis and radiolysis, forming materials that influence product losses, product decontamination, and separation efficiencies. Laboratory studies to improve online solvent cleaning have shown that carbonate washing, although removing residual solvent activity, does not remove binding ligands that hold fission products in the solvent. Treatment of solvent with a solid adsorbent removes binding ligands and significantly improves recycle solvent performance. Both laboratory work defining a full-scale adsorption process and the use of the process to clean HM Process first cycle solvent are presented

Extraction-spectrophotometric method for silicon determination in high-purity substances. 2. Silicon determination in cadmium

Energy Technology Data Exchange (ETDEWEB)

Yudelevich, I G; Shaburova, V P; Shamrina, L V [AN SSSR, Novosibirsk (USSR). Inst. Neorganicheskoj Khimii

1989-01-01

Cadmium extraction by tributyl phosphate and trialkylbenzylammonium chloride (TABAC) depending on acid (HCl, HI), extracting agent concentration, volume of aqueous and organic phases, number of extraction steps is investigated. On the basis of the obtained results the spectrophotometric method for silicon determination in cadmium and CdCl/sub 2/ using malachite green with preliminary extraction of the base by the TABAC from HCl solutions. The method detection limit is 3.9x10/sup -4/ % Si with respect to initial cadmium sample of 100 mg and 7.8x10/sup -5/ % with respect to 0.5 g of CdCl/sub 2/. The relative standard deviation is S/sub r/-0.07-0.13.

Determination of Uranium plus Plutonium by Alpha spectrometry in different matrix

International Nuclear Information System (INIS)

Equillor, Hugo E.; Campos, Juan M.

2011-01-01

Usually, the determination of alpha emitters by alpha spectrometry is performed with a prior purification of each of the elements to be quantified. In this work, a methodology for the determination of uranium and plutonium isotopes as jointly described, in order to improve analytical processing times and measurement. The method includes purifying uranium and plutonium, and the subsequent electrodeposition for alpha spectrometry measurement. The technique is based on the use of TBP (tributyl phosphate) as extractant and easy to obtain reactants. It is applicable to various matrices, including water, filters and soils. In the conditions described, is applied to small aliquots of approximately 0.5 g of solid. The technique produces high quality electrodeposits. (authors) [es

Fluidized bed incineration of transuranic contaminated waste

International Nuclear Information System (INIS)

Ziegler, D.L.; Johnson, A.J.

1978-01-01

A 9 kg/hr pilot scale fluidized bed incinerator is now being used for burning various types of radioactive waste at Rocky Flats Plant. General solid combustible waste containing halogenated materials is burned in a fluidized bed of sodium carbonate for in situ neutralization of thermally generated acidic gases. A variety of other production related materials has been burned in the incinerator, including ion exchange resin, tributyl phosphate solutions, and air filters. Successful operation of the pilot plant incinerator has led to the design and construction of a production site unit to burn 82 kg/hr of plant generated waste. Residues from incinerator operations will be processed into glass buttons utilizing a vitrification plant now under development

Simultaneous determination of U and Pu isotopes by alpha spectrometry

International Nuclear Information System (INIS)

Equillor, H.E.; Campos, J.M.

2011-01-01

Determination of actinides by alpha spectrometry is usually carried out after full separation of each of the components of the sample. The procedure presented in this paper permits U and Pu isotopes to be measured together allowing faster sample processing and measurement. The method consists in the extraction with tributyl phosphate of U and Pu isotopes from the rest of the matrix, followed by a cathodic electrodeposition to obtain alpha spectrometry suitable pieces. It can be applied to various environmental samples, such as water, filters and soil (about 0.5 g of solid sample for the described conditions). High-quality electroplated discs are essential for simultaneous processing, so a technique to achieve this requirement is also explained. (authors) [es

Detection and quantitative analysis of ferrocyanide and ferricyanide: FY 93 Florida State University Raman spectroscopy report

Energy Technology Data Exchange (ETDEWEB)

Mann, C.K.; Vickers, T.J. [Florida State Univ., Tallahassee, FL (United States). Dept. of Chemistry

1994-10-11

This report provides a summary of work to develop and investigate the feasibility of using Raman spectroscopy with tank waste materials. It contains Raman spectra from organics, such as ethylenediaminetetraacetic acid (EDTA), hydroxyethylenediaminetetraacteic acid (HEDTA), imino diacetic acid (IDA), kerosene, tributyl phosphate (TBP), acetone and butanol, anticipated to be present in tank wastes and spectra from T-107 real and BY-104 simulant materials. The results of investigating Raman for determining moisture content in tank materials are also presented. A description of software algorithms developed to process Raman spectra from a dispersive grating spectrometer system and an in initial design for a data base to support qualitative and quantitative application of remote Raman sensing with tank wastes.

Development of new extraction agents for separation of rare radioactive elements

International Nuclear Information System (INIS)

Hala, J.; Navratil, O.; Prihoda, J.; Smola, J.

1977-01-01

Certain transition elements, such as rhodium and palladium may be recovered from waste solutions produced in spent fuel reprocessing. The extraction of palladium was studied using sulfur compounds of the sulfide and sulfoxide types and the effects were investigated of the individual factors on palladium distribution between the aqueous and the organic phases. The possibility of separating hafnium in the form of extractable complexes was tested on several systems. Studied in more detail were mainly the complexes of hafnium with pyrocatechol violet, xylenol orange, and tributyl phosphate. The extraction of other metals, mainly of scandium, europium and indium was investigated in detail in the system acid aqueous phase - organophosphinic acids solution in benzene. (L.K.)

Detection and quantitative analysis of ferrocyanide and ferricyanide: FY 93 Florida State University Raman spectroscopy report

International Nuclear Information System (INIS)

Mann, C.K.; Vickers, T.J.

1994-01-01

This report provides a summary of work to develop and investigate the feasibility of using Raman spectroscopy with tank waste materials. It contains Raman spectra from organics, such as ethylenediaminetetraacetic acid (EDTA), hydroxyethylenediaminetetraacteic acid (HEDTA), imino diacetic acid (IDA), kerosene, tributyl phosphate (TBP), acetone and butanol, anticipated to be present in tank wastes and spectra from T-107 real and BY-104 simulant materials. The results of investigating Raman for determining moisture content in tank materials are also presented. A description of software algorithms developed to process Raman spectra from a dispersive grating spectrometer system and an in initial design for a data base to support qualitative and quantitative application of remote Raman sensing with tank wastes

Evaluation methods used for phosphate-solubilizing bacteria ...

African Journals Online (AJOL)

This work aimed to evaluate the different selection methods and select inorganic phosphorus-solubilizing bacteria as potential plant-growth promoters. Bacterial isolates obtained from sugarcane roots and soil were tested using solid growth media containing bicalcium phosphate and Irecê Apatite ground rock phosphate as ...

Effect of Casein Phosphopeptide-Amorphous Calcium Phosphate and Three Calcium Phosphate on Enamel Microhardness.

Science.gov (United States)

Haghgou, En Hr; Haghgoo, Roza; Roholahi, Mohamad R; Ghorbani, Zahra

2017-07-01

This study aims to investigate the effect of casein phos-phopeptide-amorphous calcium phosphate and three calcium phosphate (CPP-ACP and TCP) on increasing the microhardness of human enamel after induction of erosion. A total of 26 healthy human-impacted third molar teeth were chosen, and their hardness measured using a microhardness testing machine. The samples were immersed in Coca Cola (pH = 4.7) for 8 minutes. Then, micro-hardness was measured again, and these samples were randomly divided into four groups (two control groups and two experimental groups). (1) Negative control group: Artificial saliva was used for 10 minutes, (2) positive control group: Fluoride gel was used for 10 minutes, (3) β-TCP group: TCP was used for 10 minutes, (4) CCP-ACP group: CCP-ACP was used for 10 minutes. The final microhardness of those samples was measured, and the changes in microhardness of teeth within group and between groups were analyzed using the paired and analysis of variance tests respectively. Results were considered statistically significant at a level of p < 0.05. No significant difference was observed in microhard-ness between CPP-ACP group and TCP group (p = 0.368) during the time microhardness significantly dropped after soaking in soda. Casein phosphopeptide-amorphous calcium phosphate and TCP increased the microhardness of teeth. The increase in hardness in the TCP group was higher than in the CPP-ACP group, but this difference was not significant (p = 0.36). Casein phosphopeptide-amorphous calcium phosphate and TCP can affect the remineralization of erosive lesions.

Preparation and Characterization of Apatitic Biphasic Calcium Phosphate

International Nuclear Information System (INIS)

Thin Thin Nwe; Kyaw Naing; Khin Mar Tun; Nyunt Wynn

2005-09-01

The apatitic biphasic calcium phosphate (ABcp) consisting of hydroxyapatite (HA) and -tricalcium phosphate ( -Tcp) has been prepared by precipitation technique using slaked lime and orthophosphoric acid. The X-ray diffraction analysis of the product I (hydroxyapatite) revealed that ABcp was partially crystalline state. However, on heating at 800 C for 8 hrs, XRD pattern indicated a perfectly crystalline form of ABcp. This observation was supported by FT-IR measurement. The change in morphology regarding in the functional nature was infered by the shift in the FT-IR frequency. The optimization of the apatitic biphasic calcium phosphate was done by the variation of disodium hydrogen phosphate concentration, setting time, hardening time as well as compressive strength. The perpared cement may be used as an artificial substitution bone

Characterization of cement calcium phosphate for use dental

International Nuclear Information System (INIS)

Barros, C.M.B.; Oliveira, S.V.; Silva, M.C.; Marques, J.B.; Fook, M.V.L.

2011-01-01

Calcium phosphates are interesting biological and medical attention due to its occurrence in different animal species and humans. Ceramics based on calcium phosphate in the form of implants or porous particulate materials, have proven to be suitable replacements for bone tissue when they are only subjected to small mechanical stresses. Was obtained research laboratory DEMA/UFCG a calcium phosphate phase. The goal is to characterize the material by X-ray diffraction (XRD) in order to analyze what the phases and infrared spectroscopy (FTIR) to identify the absorption bands of the bonding characteristic. Was identified by XRD phase present in the sample is hydroxyapatite Ca/P 1.67. In infrared spectroscopy has absorption bands characteristic of the phosphate group at 1032 cm1 region. (author)

Metal Phosphates as Intermediate Temperature Proton Conducting Electrolytes

DEFF Research Database (Denmark)

Huang, Yunjie; Li, Q.F.; Pan, Chao

2012-01-01

A series of metal phosphates were synthesized and screened as potential proton conductor electrolytes for fuel cells and electrolysers operational at intermediate temperatures. Among the selected, niobium and bismuth phosphates exhibited a proton conductivity of 10-2 and 10-7 S cm-1, respectively......, under the anhydrous atmosphere at 250 °C, showing close correlation with the presence of hydroxyl groups in the phosphate phases. At the water partial pressure of above 0.6 atm, both phosphates possessed a proton conductivity to a level of above 3 x 10-2 S cm-1. Reasonable stability of the proton...... conductivity was observed under either a constant low water partial pressure or under a humidity cycling test within a period of more than 80 hours....

Immobilization of fission products in phosphate ceramic waste forms

Energy Technology Data Exchange (ETDEWEB)

Singh, D.; Wagh, A. [Argonne National Lab., IL (United States)

1997-10-01

Chemically bonded phosphate ceramics (CBPCs) have several advantages that make them ideal candidates for containing radioactive and hazardous wastes. In general, phosphates have high solid-solution capacities for incorporating radionuclides, as evidenced by several phosphates (e.g., monazites and apatites) that are natural analogs of radioactive and rare-earth elements. The phosphates have high radiation stability, are refractory, and will not degrade in the presence of internal heating by fission products. Dense and hard CBPCs can be fabricated inexpensively and at low temperature by acid-base reactions between an inorganic oxide/hydroxide powder and either phosphoric acid or an acid-phosphate solution. The resulting phosphates are extremely insoluble in aqueous media and have excellent long-term durability. CBPCs offer the dual stabilization mechanisms of chemical fixation and physical encapsulation, resulting in superior waste forms. The goal of this task is develop and demonstrate the feasibility of CBPCs for S/S of wastes containing fission products. The focus of this work is to develop a low-temperature CBPC immobilization system for eluted {sup 99}Tc wastes from sorption processes.

A novel biphasic calcium phosphate derived from fish otoliths

Science.gov (United States)

Montañez-Supelano, N. D.; Sandoval-Amador, A.; Estupiñan-Durán, H. A.; Y Peña-Ballesteros, D.

2017-12-01

Calcium phosphates are bioceramics that have been widely used as bone substitutes because they encourage the formation of bone on their surface and can improve the healing of the bone. Hydroxyapatite HA (calcium/phosphorus ratio of 1.67) and tricalcium phosphate TCP (calcium/phosphorus ratio of 1.50) are the most common calcium phosphates. Natural materials have begun to be tested to make HA or TCP such as shells of cardiidae (family of mollusks) and eggshells. The calcium phosphate obtained has a high ability to precipitate apatite. In this work, the mixed phase ceramic of beta-Tri-calcium phosphate / hydroxyapatite (β-TCP/HA) was synthesized by aqueous precipitation from fish otoliths, which are monomineralic species composed of aragonite. Otoliths of the specie Plagioscion squamosissimus, commonly called the river croaker, were used. Techniques such as DRX, Raman spectroscopy and SEM-EDS were used to characterize the raw material and the obtained material. X-ray diffraction analysis revealed the presence of two crystalline phases of calcium phosphates with 86.2% crystallinity. SEM micrographs showed agglomeration of particles with porous structure and submicron particle sizes.

Metal complex derivatives of hydrogen uranyl phosphate

International Nuclear Information System (INIS)

Grohol, D.; Blinn, E.L.

1994-01-01

Derivatives of hydrogen uranyl phosphate were prepared by incorporating transition metal complexes into the uranyl phosphate matrix. The transition metal complexes employed include bis(ethylenediamine)copper(II), bis(1,3-propanediamine)copper(II) chloride, (triethylenetetramine)copper(II), (1,4,8,11-tetraazacyclotetradecane)copper(II), (1,4,8,12-tetraazacyclopentadecane)copper(II), (1,4,8,11-tetraazacyclotetradecane)nickel(II) chloride, (triethylenetetramine)nickel(II) and others. The chemical analyses of these derivatives indicated that the incorporation of the transition metal complexes into the uranyl phosphate matrix via ion exchange was not stoichiometric. The extent of ion exchange is dependent on the size and structure of the transition metal complex. All complexes were characterized by X-ray powder diffractometry, electronic and infrared spectra, thermal analyses and chemical analysis. An attempt was made to correlate the degree of quenching of the luminescence of the uranyl ion to the spacing between the uranyl phosphate layers in the derivatives

From energy-rich phosphate compounds to warfare agents: A review on the chemistry of organic phosphate compounds

Directory of Open Access Journals (Sweden)

Luciano Albino Giusti

2008-12-01

Full Text Available The chemistry of the phosphorus-oxygen bond is widely used in biological systems in many processes, such as energy transduction and the storage, transmission and expression of genetic information, which are essential to living beings in relation to a wide variety of functions. Compounds containing this bond have been designed for many purposes, ranging from agricultural defense systems, in order to increase food production, to nerve agents, for complaining use in warfare. In this review, features related to the chemistry of organic phosphate compounds are discussed, with particular emphasis on the role of phosphate compounds in biochemical events and in nerve agents. To this aim, the energy-rich phosphate compounds are focused, particularly the mode of their use as energy currency in cells. Historical and recent studies carried out by research groups have tried to elucidate the mechanism of action of enzymes responsible for energy transduction through the use of biochemical studies, enzyme models, and artificial enzymes. Finally, recent studies on the detoxification of nerve agents based on phosphorous esters are presented, and on the utilization of chromogenic and fluorogenic chemosensors for the detection of these phosphate species.

TUCS/phosphate mineralization of actinides

Energy Technology Data Exchange (ETDEWEB)

Nash, K.L. [Argonne National Lab., IL (United States)

1997-10-01

This program has as its objective the development of a new technology that combines cation exchange and mineralization to reduce the concentration of heavy metals (in particular actinides) in groundwaters. The treatment regimen must be compatible with the groundwater and soil, potentially using groundwater/soil components to aid in the immobilization process. The delivery system (probably a water-soluble chelating agent) should first concentrate the radionuclides then release the precipitating anion, which forms thermodynamically stable mineral phases, either with the target metal ions alone or in combination with matrix cations. This approach should generate thermodynamically stable mineral phases resistant to weathering. The chelating agent should decompose spontaneously with time, release the mineralizing agent, and leave a residue that does not interfere with mineral formation. For the actinides, the ideal compound probably will release phosphate, as actinide phosphate mineral phases are among the least soluble species for these metals. The most promising means of delivering the precipitant would be to use a water-soluble, hydrolytically unstable complexant that functions in the initial stages as a cation exchanger to concentrate the metal ions. As it decomposes, the chelating agent releases phosphate to foster formation of crystalline mineral phases. Because it involves only the application of inexpensive reagents, the method of phosphate mineralization promises to be an economical alternative for in situ immobilization of radionuclides (actinides in particular). The method relies on the inherent (thermodynamic) stability of actinide mineral phases.

Cloning and expression of pineapple sucrose- phosphate synthase ...

African Journals Online (AJOL)

hope&shola

2010-12-06

Dec 6, 2010 ... phosphate; EDTA, ethylene diamine tetraacetic acid; Ivr, invertase; SS .... phenolics, tannins and artifacts due to differences of tissue composition ..... Banana sucrose-phosphate synthase gene expression during fruit ripening.

The reduction of nucleotides by ionizing radiation: uridine 5' phosphate and cytidine 3' phosphate

International Nuclear Information System (INIS)

Box, H.C.; Potter, W.R.; Budzinski, E.E.

1975-01-01

Anions formed by the addition of an electron to the uracil base were observed in single crystals of the barium salt of uridine 5' phosphate x-irradiated at 4.2 degreeK. The hyperfine coupling tensor for the C 6 --H proton was deduced from ENDOR measurements; the principal values are -59.12, -32.92, and -16.24 MHz. Similar measurements were made on single crystals of cytidine 3' phosphate. The principal values for the C 6 --H proton hyperfine coupling in the anion formed on the cytosine base are -59.26, -33.98, and -14.68 MHz

Genetics Home Reference: glucose phosphate isomerase deficiency

Science.gov (United States)

... glycolytic pathway; in this step, a molecule called glucose-6-phosphate is converted to another molecule called fructose-6-phosphate. When GPI remains a single molecule (a monomer) it is involved in the development and maintenance of nerve cells ( neurons ). In this context, it is often known as ...

Towards Phosphate Detection in Hydroponics Using Molecularly Imprinted Polymer Sensors.

Science.gov (United States)

Storer, Christopher S; Coldrick, Zachary; Tate, Daniel J; Donoghue, Jack Marsden; Grieve, Bruce

2018-02-10

An interdigitated electrode sensor was designed and microfabricated for measuring the changes in the capacitance of three phosphate selective molecularly imprinted polymer (MIP) formulations, in order to provide hydroponics users with a portable nutrient sensing tool. The MIPs investigated were synthesised using different combinations of the functional monomers methacrylic acid (MAA) and N -allylthiourea, against the template molecules diphenyl phosphate, triethyl phosphate, and trimethyl phosphate. A cross-interference study between phosphate, nitrate, and sulfate was carried out for the MIP materials using an inductance, capacitance, and resistance (LCR) meter. Capacitance measurements were taken by applying an alternating current (AC) with a potential difference of 1 V root mean square (RMS) at a frequency of 1 kHz. The cross-interference study demonstrated a strong binding preference to phosphate over the other nutrient salts tested for each formulation. The size of template molecule and length of the functional monomer side groups also determined that a short chain functional monomer in combination with a template containing large R-groups produced the optimal binding site conditions when synthesising a phosphate selective MIP.

Immobilization of radioactive strontium in contaminated soils by phosphate treatment

International Nuclear Information System (INIS)

Kim, K.H.; Ammons, J.T.

1990-01-01

The feasibility of in situ phosphate- and metal- (calcium, aluminum, and iron) solution treatment for 90 Sr immobilization was investigated. Batch and column experiments were performed to find optimum conditions for coprecipitation of 90 Sr with Ca-, Al-, and Fe-phosphate compounds in contaminated soils. Separate columns were packed with artificially 85 Sr-contaminated acid soil as well as 90 Sr-contaminated soil from the Oak Ridge Reservation. After metal-phosphate treatment, the columns were then leached successively with either tapwater or 0.001 M CaCl 2 solution. Most of the 85 Sr coprecipitated with the metal phosphate compounds. Immobilization of 85 Sr and 90 Sr was affected by such factors as solution pH, metal and phosphate concentration, metal-to-phosphate ratio, and soil characteristics. Equilibration time after treatments also affected 85 Sr immobilization. Many technology aspects still need to be investigated before field applications are feasible, but these experiments indicate that phosphate-based in situ immobilization should prevent groundwater contamination and will be useful as a treatment technology for 90 Sr-contaminated sites. 15 refs., 3 figs., 1 tab

Reactivity and transfer of tributyl-tin and mercury in aquatic environments; Etude de la reactivite et du transfert du tributyletain et du mercure dans les environnements aquatiques

Energy Technology Data Exchange (ETDEWEB)

Tessier, E

2004-12-15

Aquatic ecosystems are particularly affected by tributyl-tin (TBT) and mercury (Hg) chronic contamination. These micro-pollutants are ubiquitous and persistent and occurred at trace level, likely to drastically impair aquatic environments. TBT and Hg biogeochemical cycles are driven by transformation and transfer mechanisms between the different environmental compartments. These natural processes have been studied in details by using novel analytical methods and environmental design to improve the risk assessment. The first part of this work focus on the mechanistic study of TBT and Hg reactivity and transfer in reconstituted aquatic ecosystems. These experiments involve both state-of-the-art analytical speciation techniques, partly based on quantification by isotopic dilution and experimental tools simulating the environmental conditions. Kinetics of TBT and Hg distribution (adsorption, bioaccumulation, biodegradation, clearance) have been simultaneously characterized in all compartments of the microcosms presenting a simple biological organization. In a second step, volatilization kinetics of TBT at real interfaces have been studied to assess the potential remobilization and elimination pathways of butyl-tin compounds. Finally, in a third part, stable isotopic tracers of Hg have been employed to discriminate and quantify the coupled methylation and demethylation kinetics in estuarine sediments, by forcing different environmental factors (oxygenation, microbial activity). (author)

Phosphate-rich sedimentary rocks: significance for organic facies and petroleum exploration

Energy Technology Data Exchange (ETDEWEB)

Waples, D W

1982-03-01

Phosphorus-bearing rocks and sediments can be divided into two genetically distinct classes: phosphatic shales or limestones and phosphorites. Phosphatic shales are primary sediments in which phosphate nodules or micronodules have formed diagenetically by precipitation of calcium phosphates derived mainly from organic phosphorus. The nodules form in reducing environments at shallow depths within the sediments, where loss of phosphate by diffusion to the overlying water column is minimized. Highly biogenic sediments containing large amounts of organic matter and some fine clastic debris provide ideal environments for the formation of phosphate nodules. Phosphorites, in contrast, represent concentrated accumulations of reworked phosphate nodules which originated in phosphatic shales or limestones. Currents, wave action, recrystallization, and erosion and resedimentation are important mechanisms in the concentration process. Phosphatic shales and limestones may become excellent oil source rocks if thermal maturity is achieved. They are useful facies indicators for anoxic or nearly anoxic depositional environments, and are often associated with restricted basins, or, during certain geologic periods, with broad shelves developed during transgressions. Phosphorites, in contrast, are often correlated with sea-level regressions or uplifts. They are modest source rocks because of their low organic carbon contents and the fact that they were reworked under oxidizing conditions. Nevertheless, because phosphorites are derived from, and often grade into, phosphatic shales, they also are of potential utility in the search for oil source beds.

Dental Composites with Calcium / Strontium Phosphates and Polylysine.

Directory of Open Access Journals (Sweden)

Piyaphong Panpisut

Full Text Available This study developed light cured dental composites with added monocalcium phosphate monohydrate (MCPM, tristrontium phosphate (TSrP and antimicrobial polylysine (PLS. The aim was to produce composites that have enhanced water sorption induced expansion, can promote apatite precipitation and release polylysine.Experimental composite formulations consisted of light activated dimethacrylate monomers combined with 80 wt% powder. The powder phase contained a dental glass with and without PLS (2.5 wt% and/or reactive phosphate fillers (15 wt% TSrP and 10 wt% MCPM. The commercial composite, Z250, was used as a control. Monomer conversion and calculated polymerization shrinkage were assessed using FTIR. Subsequent mass or volume changes in water versus simulated body fluid (SBF were quantified using gravimetric studies. These were used, along with Raman and SEM, to assess apatite precipitation on the composite surface. PLS release was determined using UV spectroscopy. Furthermore, biaxial flexural strengths after 24 hours of SBF immersion were obtained.Monomer conversion of the composites decreased upon the addition of phosphate fillers (from 76 to 64% but was always higher than that of Z250 (54%. Phosphate addition increased water sorption induced expansion from 2 to 4% helping to balance the calculated polymerization shrinkage of ~ 3.4%. Phosphate addition promoted apatite precipitation from SBF. Polylysine increased the apatite layer thickness from ~ 10 to 20 μm after 4 weeks. The novel composites showed a burst release of PLS (3.7% followed by diffusion-controlled release irrespective of phosphate addition. PLS and phosphates decreased strength from 154 MPa on average by 17% and 18%, respectively. All formulations, however, had greater strength than the ISO 4049 requirement of > 80 MPa.The addition of MCPM with TSrP promoted hygroscopic expansion, and apatite formation. These properties are expected to help compensate polymerization shrinkage and

Complex formation of uranium(VI) with fructose and glucose phosphates

International Nuclear Information System (INIS)

Koban, A.; Geipel, G.; Bernhard, G.; Fanghaenel, T.

2002-01-01

The uptake of heavy metals into plants is commonly quantified by the soil-plant transfer factor. Up to now little is known about the chemical speciation of actinides in plants. To compare the obtained spectroscopic data of uranium complexes in plants with model compounds, we investigate the complexation of uranium with relevant bioligands of various functionalities. A very important class of ligands consists of phosphate esters, which serve as phosphate group and energy transmitters as well as energy storage media in biological systems. Heavy metal ions bound to the phosphate esters can be transported into living cells and then deposited. Therefore, in our study we present the results of uranium complexation with glucose-6-phosphate (G6P), and fructose-6-phosphate (F6P) obtained by time-resolved laser-induced fluorescence spectroscopy (TRLFS). The experiments were performed at a fixed uranyl concentration (10 -5 M) as a function of the ligand concentrations (10 -5 to 10 -3 M) in a pH range from 2 to 4.5. For the glucose phosphate system we observed, using increasing ligand concentrations, a decrease in the fluorescence intensity and a small red shift of the emission bands. From this we conclude that the complexed uranyl glucose phosphate species show only minor or no fluorescence properties. The TRLFS spectra of the glucose phosphate samples indicated the presence of a single species with fluorescence properties. This species has a lifetime of approximately 1.5 μs and was identified as the free uranyl ion. An opposite phenomenon was observed for the fructose phosphate system: there was no decrease in fluorescence intensity. However, a strong red shift of the spectra was observed, illustrating the fluorescence properties of the uranyl fructose phosphate complex. The TRLFS spectra of the fructose phosphate system showed a second lifetime ( 2 2+ UO 2 (lig) x (2-y)+ + y H + (lig = sugar phosphate). Applying the mass action law and transformation to the logarithmic

Effect of submarine groundwater discharge containing phosphate on coral calcification

Science.gov (United States)

Yasumoto, J.; Yasumoto, K.; Iijima, M.; Nozaki, M.; Asai, K.; Yasumoto, M. H.

2017-12-01

It is well known that the anthropogenic eutrophication enriched with various substances including phosphate in coastal waters has resulted in coral degradation. However, to the best of our knowledge, the phosphate threshold value to inhibit the coral calcification has been unclear, due to the unknown mechanisms involved in the inhibition of the calcification by phosphate. In island regions, groundwater is one of the most important clues to transport the nutrients contained in livestock or agricultural wastewaters. However, the actual conditions of coastal pollution with such nutrients have not been understood because of unperceived submarine groundwater discharge (SGD). In this study, to quantify of extremely rapid and localized SGD from Ryukyu limestone aquifer, we investigated the rate and concentration of phosphate of SGD using automated seepage mater in Yoron Island, which is located southern part of Japan. And, to elucidate the inhibition mechanisms for phosphate against coral calcification, we examined its effect on the bottom skeleton formation in primary polyps of Acropora digitifera by using the fluorescence derivatizing reagent having phosphate group (FITC-AA). As a result, the SGD was found to contain 1 to 2 µM of phosphate as much as the concentration in the coastal ground water under agricultural land. Moreover, the amount of phosphate contained in the surface layers of bottom calcareous sands close to the region of SGD were about 5 µmol/g. When the primary polyps were treated with 50 µM of FITC-AA, the bottom skeleton of the primary polyps showed the fluorescence from FITC-AA within a few minutes, suggesting the phosphate binding. Furthermore, when the polyps were treated with 10 µM of FITC-AA, irregular patterns of the elongated skeleton were observed. These results led us to conclude that phosphate is transported via a paracellular pathway to the subcalicoblastic extracellular calcifying medium. These results indicate that the phosphate adsorbed

Unsymmetrical phosphate as extractant for the extraction of nitric acid

International Nuclear Information System (INIS)

Gaikwad, R.H.; Jayaram, R.V.

2016-01-01

Tri-n-butyl phosphate (TBP) was first used as an extractant in 1944, during Manhattan project for the separation of actinides and further explored by Warf in 1949 for the extraction of Ce(IV) from aqueous nitric acid. TBP was further used as an extractant in the Plutonium Uranium Recovery by Extraction (PUREX) process. To meet the stringent requirements of the nuclear industry TBP has been extensively investigated. In spite of its wide applicability, TBP suffers from various disadvantages such as high aqueous solubility, third phase formation, chemical and radiation degradation leading to the formation of undesired products. It also suffers from incomplete decontamination of the actinides from fission products. Various attempts have been made to overcome the problems associated with TBP by way of using higher homologues of TBP such as Tri-iso amyl phosphate (TiAP), Tri-secondary butyl phosphate (TsBP), Tri amyl phosphate (TAP). It was found that in some cases the results were considerably better than those obtained with TBP for uranium/thorium extraction. The extraction of nitric acid by TBP and its higher homologues which are symmetrical are well documented. However, no solvent has emerged clearly superior than TBP. Here in we report the extraction of nitric acid with neutral unsymmetrical phosphates and study them as extractants for the extraction of nitric acid. Dibutyl secbutyl phosphate, dibutyl pentyl phosphate and dibutyl heptyl phosphate were synthesised for this purpose and the extraction of nitric acid was studied in n-dodecane. The results indicate that the substitution of one of the alkyl groups of the symmetrical phosphate adjacent to the phosphoryl (P=O) group of the phosphate does not have any pronounced effect on the extraction capacity of nitric acid. (author)

(13)C metabolic flux analysis in neurons utilizing a model that accounts for hexose phosphate recycling within the pentose phosphate pathway.

Science.gov (United States)

Gebril, Hoda M; Avula, Bharathi; Wang, Yan-Hong; Khan, Ikhlas A; Jekabsons, Mika B

2016-02-01

Glycolysis, mitochondrial substrate oxidation, and the pentose phosphate pathway (PPP) are critical for neuronal bioenergetics and oxidation-reduction homeostasis, but quantitating their fluxes remains challenging, especially when processes such as hexose phosphate (i.e., glucose/fructose-6-phosphate) recycling in the PPP are considered. A hexose phosphate recycling model was developed which exploited the rates of glucose consumption, lactate production, and mitochondrial respiration to infer fluxes through the major glucose consuming pathways of adherent cerebellar granule neurons by replicating [(13)C]lactate labeling from metabolism of [1,2-(13)C2]glucose. Flux calculations were predicated on a steady-state system with reactions having known stoichiometries and carbon atom transitions. Non-oxidative PPP activity and consequent hexose phosphate recycling, as well as pyruvate production by cytoplasmic malic enzyme, were optimized by the model and found to account for 28 ± 2% and 7.7 ± 0.2% of hexose phosphate and pyruvate labeling, respectively. From the resulting fluxes, 52 ± 6% of glucose was metabolized by glycolysis, compared to 19 ± 2% by the combined oxidative/non-oxidative pentose cycle that allows for hexose phosphate recycling, and 29 ± 8% by the combined oxidative PPP/de novo nucleotide synthesis reactions. By extension, 62 ± 6% of glucose was converted to pyruvate, the metabolism of which resulted in 16 ± 1% of glucose oxidized by mitochondria and 46 ± 6% exported as lactate. The results indicate a surprisingly high proportion of glucose utilized by the pentose cycle and the reactions synthesizing nucleotides, and exported as lactate. While the in vitro conditions to which the neurons were exposed (high glucose, no lactate or other exogenous substrates) limit extrapolating these results to the in vivo state, the approach provides a means of assessing a number of metabolic fluxes within the context of hexose phosphate recycling in the PPP from a

The Changes of P-fractions and Solubility of Phosphate Rock in Ultisol Treated by Organic Matter and Phosphate Rock

Directory of Open Access Journals (Sweden)

Heru Bagus Pulunggono

2012-09-01

Full Text Available Phosphorus (P is one of the essential elements for plant, however, its availability is mostly very low in acid soils. It is well documented that application of phosphate rock and organic matter are able to change the level of availability of P-form in acid soils. The objective of the research were to evaluate the changes of P-fractions ( resin-P, NaHCO3-Pi, and NaHCO3-Po and phosphate rock dissolution which were induced by application of organic matter (Imperata cylindrica, Pueraria javanica, dan Colopogonium mucunoides and phosphate rock in Utisol Lampung. The experiment was designed in a completely randomized design with three factors and three replications. The first factor was the types of organic matter (I. cylindrica, P. javanica, and C. mucunoides, the second factor was the rate of organic matter (0, 2.5, and 5%, and the third factor was the rate of phosphate rock (0, 40, and 80 mg P kg-1. The results showed that in the rate of 0 and 1% organic matter, the type of organic matter did not affect P-fraction of NaHCO3-Pi, but in the rate of 2.5 and 5%, NaHCO3-Pi due to application of P. javanica, and C. mucunoides higher than due to application of I. cylindrica. However, the increasing rate of organic matter increased NaHCO3-Pi. Then, P-fraction of Resin-Pi was affected by the type of organic matter, the rate of organic matter, and the rate of phosphate rock, respectively. P-fraction of resin-Pi due to application of P. javanica, and C. mucunoides was higher than due to application of I. cylindrica, but the effect of P. javanica, and C. mucunoides was not different. Increasing the rate of organic matter and phosphate rock increased P-fraction of resin-Pi and NaHCO3-Pi, but P-fraction of NaHCO3-Po was not affected by all treatments. Meanwhile, dissolution of phosphate rock was affected by the kind of organic matter and soil reaction. In the rate of 5% organic matter, dissolution of phosphate rock by application of I. cylindrica (70% was higher

Facing the challenge of predicting the standard formation enthalpies of n-butyl-phosphate species with ab initio methods

Science.gov (United States)

Saab, Mohamad; Réal, Florent; Šulka, Martin; Cantrel, Laurent; Virot, François; Vallet, Valérie

2017-06-01

Tributyl-phosphate (TBP), a ligand used in the PUREX liquid-liquid separation process of spent nuclear fuel, can form an explosive mixture in contact with nitric acid that might lead to a violent explosive thermal runaway. In the context of safety of a nuclear reprocessing plant facility, it is crucial to predict the stability of TBP at elevated temperatures. So far, only the enthalpies of formation of TBP are available in the literature with rather large uncertainties, while those of its degradation products, di-(HDBP) and mono-(H2MBP), are unknown. In this goal, we have used state-of-the art quantum chemical methods to compute the formation enthalpies and entropies of TBP and its degradation products di-(HDBP) and mono-(H2MBP) in gas and liquid phases. Comparisons of levels of quantum chemical theory revealed that there are significant effects of correlation on their electronic structures, pushing for the need of not only high level of electronic correlation treatment, namely, local coupled cluster with single and double excitation operators and perturbative treatment of triple excitations, but also extrapolations to the complete basis to produce reliable and accurate thermodynamics data. Solvation enthalpies were computed with the conductor-like screening model for real solvents [COSMO-RS], for which we observe errors not exceeding 22 kJ mol-1. We thus propose with final uncertainty of about 20 kJ mol-1 standard enthalpies of formation of TBP, HDBP, and H2MBP which amounts to -1281.7 ± 24.4, -1229.4 ± 19.6, and -1176.7 ± 14.8 kJ mol-1, respectively, in the gas phase. In the liquid phase, the predicted values are -1367.3 ± 24.4, -1348.7 ± 19.6, and -1323.8± 14.8 kJ mol-1, to which we may add about -22 kJ mol-1 error from the COSMO-RS solvent model. From these data, the complete hydrolysis of TBP is predicted as an exothermic phenomena but showing a slightly endergonic process.

Polyhexamethylene guanidine phosphate aerosol particles induce pulmonary inflammatory and fibrotic responses.

Science.gov (United States)

Kim, Ha Ryong; Lee, Kyuhong; Park, Chang We; Song, Jeong Ah; Shin, Da Young; Park, Yong Joo; Chung, Kyu Hyuck

2016-03-01

Polyhexamethylene guanidine (PHMG) phosphate was used as a disinfectant for the prevention of microorganism growth in humidifiers, without recognizing that a change of exposure route might cause significant health effects. Epidemiological studies reported that the use of humidifier disinfectant containing PHMG-phosphate can provoke pulmonary fibrosis. However, the pulmonary toxicity of PHMG-phosphate aerosol particles is unknown yet. This study aimed to elucidate the toxicological relationship between PHMG-phosphate aerosol particles and pulmonary fibrosis. An in vivo nose-only exposure system and an in vitro air-liquid interface (ALI) co-culture model were applied to confirm whether PHMG-phosphate induces inflammatory and fibrotic responses in the respiratory tract. Seven-week-old male Sprague-Dawley rats were exposed to PHMG-phosphate aerosol particles for 3 weeks and recovered for 3 weeks in a nose-only exposure chamber. In addition, three human lung cells (Calu-3, differentiated THP-1 and HMC-1 cells) were cultured at ALI condition for 12 days and were treated with PHMG-phosphate at set concentrations and times. The reactive oxygen species (ROS) generation, airway barrier injuries and inflammatory and fibrotic responses were evaluated in vivo and in vitro. The rats exposed to PHMG-phosphate aerosol particles in nanometer size showed pulmonary inflammation and fibrosis including inflammatory cytokines and fibronectin mRNA increase, as well as histopathological changes. In addition, PHMG-phosphate triggered the ROS generation, airway barrier injuries and inflammatory responses in a bronchial ALI co-culture model. Those results demonstrated that PHMG-phosphate aerosol particles cause pulmonary inflammatory and fibrotic responses. All features of fibrogenesis by PHMG-phosphate aerosol particles closely resembled the pathology of fibrosis that was reported in epidemiological studies. Finally, we expected that PHMG-phosphate infiltrated into the lungs in the form of

A phosphate transporter from the mycorrhizal fungus Glomus versiforme.

Science.gov (United States)

Harrison, M J; van Buuren, M L

1995-12-07

Vesicular-arbuscular (VA) mycorrhizal fungi form symbiotic associations with the roots of most terrestrial plants, including many agriculturally important crop species. The fungi colonize the cortex of the root to obtain carbon from their plant host, while assisting the plant with the uptake of phosphate and other mineral nutrients from the soil. This association is beneficial to the plant, because phosphate is essential for plant growth and development, especially during growth under nutrient-limiting conditions. Molecular genetic studies of these fungi and their interaction with plants have been limited owing to the obligate symbiotic nature of the VA fungi, so the molecular mechanisms underlying fungal-mediated uptake and translocation of phosphate from the soil to the plant remain unknown. Here we begin to investigate this process by identifying a complementary DNA that encodes a transmembrane phosphate transporter (GvPT) from Glomus versiforme, a VA mycorrhizal fungus. The function of the protein encoded by GvPT was confirmed by complementation of a yeast phosphate transport mutant. Expression of GvPT was localized to the external hyphae of G. versiforme during mycorrhizal associations, these being the initial site of phosphate uptake from the soil.

Iron-phosphate-based chemically bonded phosphate ceramics for mixed waste stabilization

International Nuclear Information System (INIS)

Wagh, A.S.; Jeong, S.Y.; Singh, D.

1997-01-01

In an effort to develop chemically bonded phosphate ceramics for mixed waste stabilization, a collaborative project to develop iron-phosphate based ceramics has been initiated between Argonne National Laboratory and the V. G. Khlopin Radium Institute in St. Petersburg, Russia. The starter powders are oxides of iron that are generated as inexpensive byproduct materials in the iron and steel industry. They contain iron oxides as a mixture of magnetite (Fe 3 O 4 ) and haematite (Fe 2 O 3 ). In this initial phase of this project, both of these compounds were investigated independently. Each was reacted with phosphoric acid solution to form iron phosphate ceramics. In the case of magnetite, the reaction was rapid. Adding ash as the waste component containing hazardous contaminants resulted in a dense and hard ceramic rich in glassy phase. On the other hand, the reaction of phosphoric acid solution with a mixture of haematite and ash waste contaminated with cesium and americium was too slow. Samples had to be molded under pressure. They were cured for 2-3 weeks and then hardened by heating at 350 degrees C for 3 h. The resulting ceramics in both cases were subjected to physical tests for measurement of density, open porosity, compression strength, phase analyses using X-ray diffraction and differential thermal analysis, and leaching tests using toxicity characteristic leaching procedure (TCLP) and ANS 16.1 with 7 days of leaching. Using the preliminary information obtained from these tests, we evaluated these materials for stabilization of Department of Energy's mixed waste streams

Effect of humic substances on the precipitation of calcium phosphate

Institute of Scientific and Technical Information of China (English)

SONG Yong-hui; Hermann H. HAHN; Erhard HOFFMANN; Peter G. WEIDLER

2006-01-01

For phosphorus (P) recovery from wastewater, the effect of humic substances (HS) on the precipitation of calcium phosphate was studied. Batch experiments of calcium phosphate precipitation were undertaken with synthetic water that contained 20 mg/L phosphate (as P) and 20 mg/L HS (as dissolved organic carbon, DOC) at a constant pH value in the range of 8.0-10.0. The concentration variations of phosphate, calcium (Ca) and HS were measured in the precipitation process; the crystalline state and compositions of the precipitates were analysed by powder X-ray diffraction (XRD) and chemical methods, respectively. It showed that at solution pH 8.0, the precipitation rate and removal efficiency of phosphate were greatly reduced by HS, but at solution pH ≥9.0,the effect of HS was very small. The Ca consumption for the precipitation of phosphate increased when HS was added; HS was also removed from solution with the precipitation of calcium phosphate. At solution pH 8.0 and HS concentrations ≤ 3.5 mg/L, and at pH ≥ 9.0 and HS concentrations ≤ 10 mg/L, the final precipitates were proved to be hydroxyapatite (HAP) by XRD. The increases of solution pH value and initial Ca/P ratio helped reduce the influence of HS on the precipitation of phosphate.

Phosphate Tether-Mediated Ring-Closing Metathesis for the Generation of P-Stereogenic, Z-Configured Bicyclo[7.3.1]- and Bicyclo[8.3.1]phosphates.

Science.gov (United States)

Markley, Jana L; Maitra, Soma; Hanson, Paul R

2016-02-05

A phosphate tether-mediated ring-closing metathesis (RCM) study to the synthesis of Z-configured, P-stereogenic bicyclo[7.3.1]- and bicyclo[8.3.1]phosphates is reported. Investigations suggest that C3-substitution, olefin substitution, and proximity of the forming olefin to the bridgehead carbon of the bicyclic affect the efficiency and stereochemical outcome of the RCM event. This study demonstrates the utility of phosphate tether-mediated desymmetrization of C2-symmetric, 1,3-anti-diol-containing dienes in the generation of macrocyclic phosphates with potential synthetic and biological utility.

Rock phosphate solubilization by the ectomycorrhizal fungus ...

African Journals Online (AJOL)

SAM

2014-06-18

Jun 18, 2014 ... To evaluate phosphate solubilization of ... and MHB had the potential to solubilize these phosphates by decreasing the pH and confirmed that ... Minerals like N, P, K, Ca, S, Zn, Cu and Sr are ... sterile distilled water, chopped, homogenized in 10 ml sterile .... The role of carbon source is important in mineral.

Genetics Home Reference: glucose-6-phosphate dehydrogenase deficiency

Science.gov (United States)

... deficiency Encyclopedia: Glucose-6-phosphate dehydrogenase test Encyclopedia: Hemolytic anemia Encyclopedia: Newborn jaundice Health Topic: Anemia Health Topic: G6PD Deficiency Health Topic: Newborn Screening Genetic and Rare Diseases Information Center (1 link) Glucose-6-phosphate dehydrogenase ...

Thermochemical investigations on uranyl phosphates and arsenates

International Nuclear Information System (INIS)

Barten, H.

1986-01-01

Results are described of a study of the thermochemical stability of anhydrous phosphates and arsenates. The results of phase studies deal with compound formation and characterization, coexisting phases and limiting physical or chemical properties. The uranyl phosphates evolve oxygen at higher temperatures and the arsenates lose arsenic oxide vapour. These phenomena give the possibility to describe their thermodynamic stabilities. Thus oxygen pressures of uranyl phosphates have been measured using a static, non-isothermal method. Having made available the pure anhydrous compounds in the course of this investigation, molar thermodynamic quantities have been measured as well. These include standard enthalpies of formation from solution calorimetry and high-temperature heat-capacity functions derived from enthalpy increments measured. Some attention is given to compounds with uranium in valencies lower than six which have been met during the investigation. An evaluation is made of the thermodynamics of the compounds studied, to result in tabulized high-temperature thermodynamic functions. Relative stabilities within the systems are discussed and comparisons of the uranyl phosphates and the arsenates are made. (Auth.)

[Tetany secondary to phosphate enema toxicity, case report].

Science.gov (United States)

Núñez Sánchez, María José; Leighton Swaneck, Sofía; Díaz, Franco

2017-06-01

Phosphate enemas are frequently used in the treatment of constipation. Errors in dosage and administration can lead to severe complications. To report a case of severe toxicity of phosphate enemas in a child with no risk factors. 2 years old female, with functional constipation, was brought to emergency department because abdominal pain. She was diagnosed with fecal impaction and received half a bottle of Fleet Adult® (Laboratorio Synthon, Chile) two times, with no clinical resolution, deciding to start proctoclisis in pediatric ward. Soon after admission, she presented painful tetany, but alert and oriented. Patient was transferred to PICU where severe hyperphosphatemia and secondary hypocalcemia were confirmed. Her treatment included electrolyte correction; removal of residual phosphate enema and hyperhydration. Tetany resolved over 2 hours after admission and no other complications. Proctoclisis was performed and patient was discharged three days after admission with pharmacological management of constipation. Phosphate enemas may cause serious complications in children with no risk factors. Errors in dosage, administration and removal of the enema are causes of toxicity in this group. Pediatricians and health personnel must be aware of risks and signs of toxicity of phosphate enema.

Degradation processes of reinforced concretes by combined sulfate–phosphate attack

Energy Technology Data Exchange (ETDEWEB)

Secco, Michele, E-mail: michele.secco@unipd.it [Inter-Departmental Research Center for the Study of Cement Materials and Hydraulic Binders (CIRCe), University of Padova, Via Gradenigo 6, 35131 Padova (Italy); Department of Civil, Environmental and Architectural Engineering (ICEA), University of Padova, Via Marzolo 9, 35131 Padova (Italy); Lampronti, Giulio Isacco, E-mail: gil21@cam.ac.uk [Department of Earth Sciences, University of Cambridge, Downing Street, CB2 3EQ Cambridge (United Kingdom); Schlegel, Moritz-Caspar, E-mail: moritz-caspar.schlegel@helmholtz-berlin.de [BAM Federal Institute for Materials Research and Testing, Unter den Eichen 87, 12205 Berlin (Germany); Helmholtz-Zentrum Berlin fürMaterialien und Energie GmbH, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Maritan, Lara, E-mail: lara.maritan@unipd.it [Department of Geosciences, University of Padova, Via Gradenigo 6, 35131 Padova (Italy); Zorzi, Federico, E-mail: federico.zorzi@unipd.it [Department of Geosciences, University of Padova, Via Gradenigo 6, 35131 Padova (Italy)

2015-02-15

A novel form of alteration due to the interaction between hydrated cement phases and sulfate and phosphate-based pollutants is described, through the characterization of concrete samples from an industrial reinforced concrete building. Decalcification of the cement matrices was observed, with secondary sulfate and phosphate-based mineral formation, according to a marked mineralogical and textural zoning. Five alteration layers may be detected: the two outermost layers are characterized by the presence of gypsum–brushite solid solution phases associated with anhydrous calcium sulfates and phosphates, respectively, while a progressive increase in apatite and ammonium magnesium phosphates is observable in the three innermost layers, associated with specific apatite precursors (brushite, octacalcium phosphate and amorphous calcium phosphate, respectively). The heterogeneous microstructural development of secondary phases is related to the chemical, pH and thermal gradients in the attacked cementitious systems, caused by different sources of pollutants and the exposure to the sun's radiation.

Occupational radiation risks in conveyance of bulk phosphate and potash

International Nuclear Information System (INIS)

Grof, Y.; Even, O.; Schlesinger, T.; Margaliot, M.

1996-01-01

The issue of occupational ionizing radiation risks encountered in the conveyance and storage of Phosphates and Potash as loose cargo got very minor attention from the national health and occupational safety authorities in the world. In Israel, the Phosphates include an average 100- 150 ppm of Uranium in equilibrium with its daughters, while in Phosphates produced in most other countries the inaction reaches regularly only few ppm up to 50 ppm. Because of the high content of the Uranium in the Phosphate in Israel we must take into consideration the radiological implications involved in the handling of this mineral. The radiological implications of handling Potash are less significant but can not be neglected as we demonstrate bellow In this presentation we will estimate the occupational radiological risks involved in the storing and transportation of Phosphate and Potash. Note, that the main risk in working with Phosphate and Potash is the risk from the dust itself (authors)

Occupational radiation risks in conveyance of bulk phosphate and potash

Energy Technology Data Exchange (ETDEWEB)

Grof, Y; Even, O; Schlesinger, T; Margaliot, M [Israel Atomic Energy Commission, Yavne (Israel). Soreq Nuclear Research Center

1996-12-01

The issue of occupational ionizing radiation risks encountered in the conveyance and storage of Phosphates and Potash as loose cargo got very minor attention from the national health and occupational safety authorities in the world. In Israel, the Phosphates include an average 100- 150 ppm of Uranium in equilibrium with its daughters, while in Phosphates produced in most other countries the inaction reaches regularly only few ppm up to 50 ppm. Because of the high content of the Uranium in the Phosphate in Israel we must take into consideration the radiological implications involved in the handling of this mineral. The radiological implications of handling Potash are less significant but can not be neglected as we demonstrate bellow In this presentation we will estimate the occupational radiological risks involved in the storing and transportation of Phosphate and Potash. Note, that the main risk in working with Phosphate and Potash is the risk from the dust itself (authors).

Reducing the cadmium content of crude phosphates and mineral fertilizers

Energy Technology Data Exchange (ETDEWEB)

Plessen, H von; Schimmel, G

1987-10-01

Crude sedimentary phosphates generally contain cadmium together with traces of other heavy metals. These Cd traces generally end up in fertilizers produced from the crude phosphates. Processes have therefore been developed to separate the Cd from the crude phosphate or from the crude phosphoric acids arising therefrom as intermediates. In this way, the Cd content of the crude phosphate can be reduced to less the 10% of its original value, and to 50% thereof by extractive treatment with acidic calcium nitrate solution. Older calcination processes for crude phosphate have been improved to give residual Cd contents of 10 to 50% at temperatures of 800 to 1000/sup 0/C. Cadmium can be removed almost quantitatively from crude phosphate by means of dialkyl dithiophosphoric acid esters by extraction, binding to adsorbents, or ion flotation. Cadmium can be extracted from crude acids in high yield by long-chained amines. After partial neutralization of the crude acids, precipitation as cadmium sulphide is also possible.

Degradation processes of reinforced concretes by combined sulfate–phosphate attack

International Nuclear Information System (INIS)

Secco, Michele; Lampronti, Giulio Isacco; Schlegel, Moritz-Caspar; Maritan, Lara; Zorzi, Federico

2015-01-01

A novel form of alteration due to the interaction between hydrated cement phases and sulfate and phosphate-based pollutants is described, through the characterization of concrete samples from an industrial reinforced concrete building. Decalcification of the cement matrices was observed, with secondary sulfate and phosphate-based mineral formation, according to a marked mineralogical and textural zoning. Five alteration layers may be detected: the two outermost layers are characterized by the presence of gypsum–brushite solid solution phases associated with anhydrous calcium sulfates and phosphates, respectively, while a progressive increase in apatite and ammonium magnesium phosphates is observable in the three innermost layers, associated with specific apatite precursors (brushite, octacalcium phosphate and amorphous calcium phosphate, respectively). The heterogeneous microstructural development of secondary phases is related to the chemical, pH and thermal gradients in the attacked cementitious systems, caused by different sources of pollutants and the exposure to the sun's radiation

Calcium-phosphate-osteopontin particles for caries control

DEFF Research Database (Denmark)

Schlafer, Sebastian; Birkedal, Henrik; Olsen, Jakob

2016-01-01

Caries is caused by acid production in biofilms on dental surfaces. Preventing caries therefore involves control of microorganisms and/or the acid produced. Here, calcium-phosphate-osteopontin particles are presented as a new approach to caries control. The particles are made by co......-precipitation and designed to bind to bacteria in biofilms, impede biofilm build-up without killing the microflora, and release phosphate ions to buffer bacterial acid production if the pH decreases below 6. Analysis of biofilm formation and pH in a five-species biofilm model for dental caries showed that treatment......H always remained above 5.5. Hence, calcium-phosphate-osteopontin particles show potential for applications in caries control....

Iron phosphate materials as cathodes for lithium batteries

CERN Document Server

Prosini, Pier Paolo

2011-01-01

""Iron Phosphate Materials as Cathodes for Lithium Batteries"" describes the synthesis and the chemical-physical characteristics of iron phosphates, and presents methods of making LiFePO4 a suitable cathode material for lithium-ion batteries. The author studies carbon's ability to increase conductivity and to decrease material grain size, as well as investigating the electrochemical behaviour of the materials obtained. ""Iron Phosphate Materials as Cathodes for Lithium Batteries"" also proposes a model to explain lithium insertion/extraction in LiFePO4 and to predict voltage profiles at variou

21 CFR 184.1697 - Riboflavin-5′-phosphate (sodium).

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Riboflavin-5â²-phosphate (sodium). 184.1697 Section... SAFE Listing of Specific Substances Affirmed as GRAS § 184.1697 Riboflavin-5′-phosphate (sodium). (a) Riboflavin-5′-phosphate (sodium) (C17H20N4O9PNa·2H2O, CAS Reg. No 130-40-5) occurs as the dihydrate in yellow...

40 CFR 422.40 - Applicability; description of the defluorinated phosphate rock subcategory.

Science.gov (United States)

2010-07-01

... defluorinated phosphate rock subcategory. 422.40 Section 422.40 Protection of Environment ENVIRONMENTAL... Defluorinated Phosphate Rock Subcategory § 422.40 Applicability; description of the defluorinated phosphate rock... phosphate rock by application of high temperature treatment along with wet process phosphoric acid, silica...

Structural basis for phosphatidylinositol-phosphate biosynthesis

Science.gov (United States)

Clarke, Oliver B.; Tomasek, David; Jorge, Carla D.; Dufrisne, Meagan Belcher; Kim, Minah; Banerjee, Surajit; Rajashankar, Kanagalaghatta R.; Shapiro, Lawrence; Hendrickson, Wayne A.; Santos, Helena; Mancia, Filippo

2015-10-01

Phosphatidylinositol is critical for intracellular signalling and anchoring of carbohydrates and proteins to outer cellular membranes. The defining step in phosphatidylinositol biosynthesis is catalysed by CDP-alcohol phosphotransferases, transmembrane enzymes that use CDP-diacylglycerol as donor substrate for this reaction, and either inositol in eukaryotes or inositol phosphate in prokaryotes as the acceptor alcohol. Here we report the structures of a related enzyme, the phosphatidylinositol-phosphate synthase from Renibacterium salmoninarum, with and without bound CDP-diacylglycerol to 3.6 and 2.5 Å resolution, respectively. These structures reveal the location of the acceptor site, and the molecular determinants of substrate specificity and catalysis. Functional characterization of the 40%-identical ortholog from Mycobacterium tuberculosis, a potential target for the development of novel anti-tuberculosis drugs, supports the proposed mechanism of substrate binding and catalysis. This work therefore provides a structural and functional framework to understand the mechanism of phosphatidylinositol-phosphate biosynthesis.

Phosphate Phosphors for Solid-State Lighting

CERN Document Server

Shinde, Kartik N; Swart, H C; Park, Kyeongsoon

2012-01-01

The idea for this book arose out of the realization that, although excellent surveys and a phosphor handbook are available, there is no single source covering the area of phosphate based phosphors especially for lamp industry. Moreover, as this field gets only limited attention in most general books on luminescence, there is a clear need for a book in which attention is specifically directed toward this rapidly growing field of solid state lighting and its many applications. This book is aimed at providing a sound introduction to the synthesis and optical characterization of phosphate phosphor for undergraduate and graduate students as well as teachers and researchers. The book provides guidance through the multidisciplinary field of solid state lighting specially phosphate phosphors for beginners, scientists and engineers from universities, research organizations, and especially industry. In order to make it useful for a wide audience, both fundamentals and applications are discussed, together.

Biosolubilization of poorly soluble rock phosphates by Aspergillus tubingensis and Aspergillus niger

Energy Technology Data Exchange (ETDEWEB)

Reddy, M.S.; Kumar, S.; Babita, K. [Thapar Institute of Engineering and Technology, Patiala (India). School of Biotechnology; Reddy, M.S. [Auburn University, AL (United States). Department of Entomology and Plant Pathology

2002-09-01

Three isolates of Aspergillus tubingensis and two isolates of Aspergillus niger isolated from rhizospheric soils were tested on solubilization of different rock phosphates. All the isolates of Aspergillus were capable of solubilizing all the natural rock phosphates. A. tubingensis (AT1) showed maximum percent solubilization in all the rock phosphates tested in this study when compared to other isolates. This isolate also showed highest phosphorus (P) solubilization when grown in the presence of 2% of rock phosphate. A. tubingensis (AT1) seems to be more efficient in solubilization of rock phosphates compared to other isolates reported elsewhere. This is the first report of rock phosphate solubilization by A. tubingensis and might provide an efficient large scale biosolubilization of rock phosphates intended for P fertilizer. (author)

The radiological impact of the Belgian phosphate industry

Energy Technology Data Exchange (ETDEWEB)

Vanmarcke, H.; Paridaens, J. [Belgian Nuclear Research Centre, SCK.CEN, Boeretang 200, 2400 Mol (Belgium)

2006-07-01

The Belgian phosphate industry processes huge amounts of phosphate ore (1.5 to 2 Mton/year) for a wide range of applications, the most important being the production of phosphoric acid, fertilizers and cattle food. Marine phosphate ores show high specific activities of the natural uranium decay series (usually indicated by Ra-226) (e.g. 1200 to 1500 Bq/kg for Moroccan ore). Ores of magmatic origin generally contain less of the uranium and more of the thorium decay series (up to 500 Bq/kg). These radionuclides turn up in by-products, residues or product streams depending on the processing method and the acid used for the acidulation of the phosphate rock. Sulfuric acid is the most widely used, but also hydrochloric acid and nitric acid are applied in Belgium. For Flanders, the northern part of Belgium, we already have a clear idea of the production processes and waste streams. The five Flemish phosphate plants, from 1920 to 2000, handled 54 million ton of phosphate ore containing 65 TBq of radium-226 and 2.7 TBq of thorium- 232. The total surface area of the phosphogypsum and calcium fluoride sludge deposits amounts to almost 300 ha. There is also environmental contamination along two small rivers receiving the waste waters of the hydrochloric production process: the Winterbeek (> 200 ha) and the Grote Laak (12 ha). The data on the impact of the phosphate industry in the Walloon provinces in Belgium is less complete. A large plant produced in 2004 0.8 Mton of phosphogypsum, valorizing about 70 % of the gypsum in building materials (plaster, cement), in fertilizers, and in other products such as paper. The remainder was stored on a local disposal site. The radiological impact of the Belgian phosphate industry on the local population will be discussed. At present most contaminated areas are still recognizable as waste deposits and inaccessible to the population. However as gypsum deposits and other contaminated areas quickly blend in with the landscape, it is

Volumetric, acoustic and viscometric behaviour of dipotassium hydrogen phosphate and disodium hydrogen phosphate in aqueous solution of N-acetyl glycine at different temperatures

International Nuclear Information System (INIS)

Kumar, Harsh; Singla, Meenu; Mittal, Heena

2016-01-01

Highlights: • Densities, speeds of sound, viscosities of phosphate salts in aqueous N-acetyl glycine. • Large values of partial molar volume for dipotassium hydrogen phosphate. • Partial molar volume of transfer are positive for phosphate salts. • Positive B-coefficient values indicate ion–solvent interactions. - Abstract: Densities, speeds of sound and viscosities of dipotassium hydrogen phosphate (DPHP) and disodium hydrogen phosphate (DSHP) in aqueous solutions of N-acetyl glycine (AcGly) are reported at different temperatures. Densities and speeds of sound have been used to calculate apparent molar volume, apparent molar isentropic compression, partial molar volume, partial molar isentropic compression, partial molar volume of transfer, partial molar isentropic compression of transfer and partial molar expansivity. Pair and triplet interaction coefficients have also been calculated. Experimental viscosities have been used to determine B-coefficients. Further pair and triplet interaction coefficients have also been calculated. The results are discussed in terms of solute–solvent interactions.

Preferable adsorption of phosphate using lanthanum-incorporated porous zeolite: Characteristics and mechanism

Science.gov (United States)

He, Yinhai; Lin, Hai; Dong, Yingbo; Wang, Liang

2017-12-01

The adsorbent, where lanthanum oxide was incorporated onto porous zeolite (La-Z), of preferable adsorption towards phosphate was prepared by hydrothermal synthesis. Based on pH effect results, La-Z would effectively sequestrate phosphate over wider pH range of 3.0-7.0, alkaline conditions were unfavorable for phosphate. The adsorption of phosphate was not significantly influenced by ionic strength and by coexisting anions of chloride, nitrate and sulfate but bicarbonate showed slightly greater negative effects, indicating La-Z possessed highly selectivity to phosphate. Adsorption of phosphate could be well fitted by pseudo-second-order model and the process was mainly controlled by intra-particle diffusion. Equilibrium adsorption demonstrated that Langmuir model was more suitable than Freundlich model for description phosphate adsorption and the adsorption capacity was 17.2 mg P g-1, which exhibited 95% utilization of incorporated La. Over 95% phosphate was eliminated in real effluent treatment when the dose was 2 g L-1. The underlying mechanism for phosphate capture was probed with Zeta potential and X-ray photoelectron spectroscope analysis, and the formation of La-P inner-sphere complexation was testified to be the dominant pathway. All the results suggested that the porous zeolite-supported lanthanum oxide can serve as a promising adsorbent for phosphate removal in realistic application.

Synthesis and Characterization of Metal Phosphates for Photocatalytic Applications

KAUST Repository

Al-Sabban, Bedour

2012-07-01

Solar energy is the most abundant efficient and important source of renewable energy. The objective of this study is to develop highly efficient visible light responsive photocatalysts for overall water splitting. This is done by using silver or copper containing materials. Phosphate compounds have caught much attention due to their rigid structure, thermal stability and resistance to chemical attacks. Solid phosphates can be prepared by direct solid-state reaction between metal cations and phosphate anions at high temperatures. Double metal phosphates of the Nasion-type structure had shown further technological importance. It has been reported that well-crystallized double metal phosphate particles have excellent ordering and cationic conduction channels in the Nasicon framework. In this study, several Nasion-type structured materials have been synthesized by solid-state method (e.g. CuTi2(PO4)3 and AgTi2(PO4)3) heated up under different temperatures (400–1100C) in N2 or air atmosphere. These materials were characterized by XRD, SEM, DR-UV-Vis spectroscopy and tested for photocatalytic applications. A new method for direct synthesis of photoelectrode on Ti Plate had been demonstrated. Further investigations on controlling the size and morphology for better performance of single and double metal phosphates will be done.

Effect of Phosphate levels on vegetables irrigated with wastewater

Science.gov (United States)

Oladeji, S. O.; Saeed, M. D.

2018-04-01

This study examined accumulation of phosphate ions in wastewater and vegetables through man-made activities. Phosphate level was determined in wastewater and vegetables collected on seasonal basis along Kubanni stream in Zaria using UV/Visible and Smart Spectro Spectrophotometers for their analyses. Results obtained show that phosphate concentrations ranged from 3.85 – 42.33 mg/L in the first year and 15.60 – 72.80 mg/L in the second year for wastewater whereas the vegetable had levels of 3.80 – 23.65 mg/kg in the year I and 7.48 – 27.15 mg/kg in the year II. Further statistical tests indicated no significant difference in phosphate levels across the locations and seasons for wastewater and vegetables evaluated. Correlation results for these two years indicated negative (r = -0.062) relationship for wastewater while low (r = 0.339) relationship noticed for vegetables planted in year I to that of year II. Phosphate concentrations obtained in this study was higher than Maximum Contaminant Levels set by Standard Organization such as WHO and FAO for wastewater whereas vegetables of the sampling sites were not contaminated with phosphate ions. Irrigating farmland with untreated wastewater has negative consequence on the crops grown with it.

Metal Phosphides and Phosphates-based Electrodes for Electrochemical Supercapacitors.

Science.gov (United States)

Li, Xin; Elshahawy, Abdelnaby M; Guan, Cao; Wang, John

2017-10-01

Phosphorus compounds, such as metal phosphides and phosphates have shown excellent performances and great potential in electrochemical energy storage, which are demonstrated by research works published in recent years. Some of these metal phosphides and phosphates and their hybrids compare favorably with transition metal oxides/hydroxides, which have been studied extensively as a class of electrode materials for supercapacitor applications, where they have limitations in terms of electrical and ion conductivity and device stability. To be specific, metal phosphides have both metalloid characteristics and good electric conductivity. For metal phosphates, the open-framework structures with large channels and cavities endow them with good ion conductivity and charge storage capacity. In this review, we present the recent progress on metal phosphides and phosphates, by focusing on their advantages/disadvantages and potential applications as a new class of electrode materials in supercapacitors. The synthesis methods to prepare these metal phosphides/phosphates are looked into, together with the scientific insights involved, as they strongly affect the electrochemical energy storage performance. Particular attentions are paid to those hybrid-type materials, where strong synergistic effects exist. In the summary, the future perspectives and challenges for the metal phosphides, phosphates and hybrid-types are proposed and discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

3D printing of octacalcium phosphate bone substitutes

Directory of Open Access Journals (Sweden)

Vladimir S. Komlev

2015-06-01

Full Text Available Biocompatible calcium phosphate ceramic grafts are able of supporting new bone formation in appropriate environment. The major limitation of these materials usage for medical implants is the absence of accessible methods for their patient-specific fabrication. 3D printing methodology is an excellent approach to overcome the limitation supporting effective and fast fabrication of individual complex bone substitutes. Here we proposed a relatively simple route for 3D printing of octacalcium phosphates in complexly shaped structures by the combination of inkjet printing with post-treatment methodology. The printed octacalcium phosphate blocks were further implanted in the developed cranial bone defect followed by histological evaluation. The obtained result confirmed the potential of the developed octacalcium phosphates bone substitutes, which allowed 2.5-time reducing of defect’s diameter at 6.5 months in a region where native bone repair is extremely inefficient.

Biodegradation of tert-butylphenyl diphenyl phosphate

International Nuclear Information System (INIS)

Heitkamp, M.A.; Freeman, J.P.; Cerniglia, C.E.

1986-01-01

The biodegradation of tert-butylphenyl diphenyl phosphate (BPDP) was examined in microcosms containing sediment and water from five different ecosystems as part of studies to elucidate the environmental fate of phosphate ester flame retardants. Biodegradation of [ 14 C]BPDP was monitored in the environmental microcosms by measuring the evolution of 14 CO 2 . Over 37% of BPDP was mineralized after 8 weeks in microcosms from an ecosystem which had chronic exposure to agricultural chemicals. In contrast, only 1.7% of BPDP was degraded to 14 CO 2 in samples collected from a noncontaminated site. The exposure concentration of BPDP affected the percentage which was degraded to 14 CO 2 in microcosms from the two most active ecosystems. Mineralization was highest at a concentration of 0.1 mg of BPDP and was inhibited with 10- and 100-fold higher concentrations of BPDP. The authors observed adaptive increases in both microbial populations and phosphoesterase enzymes in some sediments acclimated to BPDP. Chemical analyses of the residues in the microcosms indicated undegraded BPDP and minor amounts of phenol, tert-butylphenol, diphenyl phosphate, and triphenyl phosphate as biodegradation products. These data suggest that the microbial degradation of BPDP results from at least three catabolic processes and is highest when low concentrations of BPDP are exposed to sediment microorganisms of eutrophic ecosystems which have high phosphotri- and diesterase activities and previous exposure to anthropogenic chemicals

Immobilization of transition metal ions on zirconium phosphate monolayers

International Nuclear Information System (INIS)

Melezhik, A.V.; Brej, V.V.

1998-01-01

It is shown that ions of transition metals (copper, iron, vanadyl, titanium) are adsorbed on zirconium phosphate monolayers. The zirconium phosphate threshold capacity corresponds to substitution of all protons of hydroxyphosphate groups by equivalent amounts of copper, iron or vanadyl. Adsorption of polynuclear ions is possible in case of titanium. The layered substance with specific surface up to 300 m 2 /g, wherein ultradispersed titanium dioxide particles are intercalirated between zirconium-phosphate layers, is synthesized

Effect of humic acid preloading on phosphate adsorption onto zirconium-modified zeolite.

Science.gov (United States)

Lin, Jianwei; Zhang, Zhe; Zhan, Yanhui

2017-05-01

A zirconium-modified zeolite (ZrMZ) was prepared, and then, humic acid (HA) was immobilized on the ZrMZ surface to prepare HA-loaded ZrMZ (HA-ZrMZ). The obtained ZrMZ and HA-ZrMZ were characterized by energy dispersive X-ray spectroscopy, elemental analyzer, N 2 adsorption/desorption isotherms, pH at the point of zero charge, and X-ray photoelectron spectroscopy. The adsorption characteristics of phosphate on ZrMZ and HA-ZrMZ were comparatively investigated in batch mode. The adsorption mechanism of phosphate on ZrMZ and HA-ZrMZ was investigated by ionic strength effect and 31 P nuclear magnetic resonance. The mechanism for phosphate adsorption onto ZrMZ was the formation of inner-sphere phosphate complexes at the solid/solution interface. The preloading of HA on ZrMZ reduced the phosphate adsorption capacity, and the more the HA loading amount, the lower the phosphate adsorption capacity. However, the preloading of HA on ZrMZ did not change the phosphate adsorption mechanism; i.e., the formation of inner-sphere phosphate surface complexes was still responsible for the adsorption of phosphate on HA-ZrMZ. The decreased phosphate adsorption capacity for ZrMZ after HA coating could be attributed to the fact that the coating of HA on ZrMZ reduced the amount of binding active sites available for phosphate adsorption, changed the adsorbent surface charges, and reduced the specific surface areas and pore volumes of ZrMZ.

Multivariate statistical analysis of radioactive variables in two phosphate ores from Sudan

International Nuclear Information System (INIS)

Adam, Abdel Majid A.; Eltayeb, Mohamed Ahmed H.

2012-01-01

Multivariate statistical techniques are efficient ways to display complex relationships among many objects. An attempt was made to study the radioactive data in two types of Sudanese phosphate deposits; Kurun and Uro phosphate, using several multivariate statistical methods. Pearson correlation coefficient revealed that a U-238 distribution in Kurun phosphate is controlled by the variation of K-40 concentration, whereas in Uro phosphate it is controlled by the variation of U-235 and U-234 concentration. Histograms and normal Q–Q plots clearly show that the radioactive variables did not follow a normal distribution. This non-normality feature observed may be attributed to complicating influence of geological factors. The principal components analysis (PCA) gives a model of five components for representing the acquired data from Kurun phosphate, where 89.5% of the total variance is explained. A model of four components was sufficient to represent the acquired data from Uro phosphate, where 87.5% of the total data variance is explained. The hierarchical cluster analysis (HCA) indicates that U-238 behaves in the same manner in the two types of phosphates; it associated with a group of four radionuclides; U-234, Po-210, Ra-226, Th-230, which the most abundant radionuclides, and all belong to the uranium-238 decay series. Two parameters have been adapted for the direct differentiate between the two phosphates. Firstly, U-238 in Uro phosphate have shown higher degree of mobility (CV% = 82.6) than that in Kurun phosphate (CV% = 64.7), and secondly, the activity ratio of Th-230/Th-232 in Uro phosphate is nine times than that in Kurun phosphate. - Highlights: ► Multivariate statistical techniques were used to characterize radioactive data. ► U-238 in Uro phosphate shows higher degree of mobility (CV% = 82.6). ► U-238 in Kurun phosphate shows lower degree of mobility (CV% = 64.7). ► The radioactive variables did not follow a normal distribution. ► The ratio of Th

Preparation of Edible Corn Starch Phosphate with Highly Reactive ...

African Journals Online (AJOL)

1Food & Bioengineering Department, Henan University of Science and Technology, Luoyang, Henan 471003 ... Purpose: To prepare edible corn starch phosphate under optimized experimental conditions. ... In food industry, starch phosphate.

Characterisation of Phosphate Accumulating Organisms and Techniques for Polyphosphate Detection: A Review

Directory of Open Access Journals (Sweden)

Cédric Tarayre

2016-05-01

Full Text Available Phosphate minerals have long been used for the production of phosphorus-based chemicals used in many economic sectors. However, these resources are not renewable and the natural phosphate stocks are decreasing. In this context, the research of new phosphate sources has become necessary. Many types of wastes contain non-negligible phosphate concentrations, such as wastewater. In wastewater treatment plants, phosphorus is eliminated by physicochemical and/or biological techniques. In this latter case, a specific microbiota, phosphate accumulating organisms (PAOs, accumulates phosphate as polyphosphate. This molecule can be considered as an alternative phosphate source, and is directly extracted from wastewater generated by human activities. This review focuses on the techniques which can be applied to enrich and try to isolate these PAOs, and to detect the presence of polyphosphate in microbial cells.

Sorption of phosphate onto calcite; results from batch experiments and surface complexation modeling

DEFF Research Database (Denmark)

Sø, Helle Ugilt; Postma, Dieke; Jakobsen, Rasmus

2011-01-01

The adsorption of phosphate onto calcite was studied in a series of batch experiments. To avoid the precipitation of phosphate-containing minerals the experiments were conducted using a short reaction time (3h) and low concentrations of phosphate (⩽50μM). Sorption of phosphate on calcite was stud......The adsorption of phosphate onto calcite was studied in a series of batch experiments. To avoid the precipitation of phosphate-containing minerals the experiments were conducted using a short reaction time (3h) and low concentrations of phosphate (⩽50μM). Sorption of phosphate on calcite...... of a high degree of super-saturation with respect to hydroxyapatite (SIHAP⩽7.83). The amount of phosphate adsorbed varied with the solution composition, in particular, adsorption increases as the CO32- activity decreases (at constant pH) and as pH increases (at constant CO32- activity). The primary effect...... of ionic strength on phosphate sorption onto calcite is its influence on the activity of the different aqueous phosphate species. The experimental results were modeled satisfactorily using the constant capacitance model with >CaPO4Ca0 and either >CaHPO4Ca+ or >CaHPO4- as the adsorbed surface species...

Engineering potato starch with a higher phosphate content

NARCIS (Netherlands)

Xu, Xuan; Huang, Xing Feng; Visser, Richard G.F.; Trindade, Luisa M.

2017-01-01

Phosphate esters are responsible for valuable and unique functionalities of starch for industrial applications. Also in the cell phosphate esters play a role in starch metabolism, which so far has not been well characterized in storage starch. Laforin, a human enzyme composed of a

Development of a fully injectable calcium phosphate cement

Indian Academy of Sciences (India)

Permanent link: https://www.ias.ac.in/article/fulltext/boms/026/04/0415-0422. Keywords. Calcium phosphate cements; hydroxyapatite; bioceramics; bone substitute; orthopedic; dental. Abstract. A study on the development of a fully injectable calcium phosphate cement for orthopedic and dental applications is presented.

Mineral phosphate solubilizing bacterial community in agro-ecosystem

African Journals Online (AJOL)

Mineral phosphate solubilizing bacterial community in agro-ecosystem. N Saha, S Biswas. Abstract. The present communication deals with the assessment of phosphate solubilizing bacterial community structure across artificially created fertility gradient with regards to N, P and K status of soil in the experimental site.

Potential for phosphate mitigation from agricultural runoff by three aquatic macrophytes

Science.gov (United States)

Phosphate from agricultural runoff is considered a contributor to eutrophication. Three aquatic macrophyte species, Leersia oryzoides, Typha latifolia, and Sparganium americanum, were investigated for their phosphate mitigation ability. Mesocosms were exposed to flowing phosphate enriched water (1...

Investigation of calcium phosphate coatings for biomedical applications

International Nuclear Information System (INIS)

Yusof Abdullah; Idris Besar; Muhammad Jamal Md Isa; Mohamad Abd Razak; Hyzan Mohd Yusof

1999-01-01

Calcium phosphate is the main constituent of our bone and tooth minerals. The use of this bioactive material for coating implant such as artificial joint prosthesis, therefore, can promote biological fixation and enhance biocompatibility. Our initial work has been focused on the evaluation of experimental conditions of coating preparation and the effects of post-deposition calcium phosphate coatings on stainless steel substrates. The coating layers were produced by the precipitation technique and coatings were carried out in sol-gel by the dipping method. For comparison purposes a wet method was used to obtain a fine calcium phosphate ceramic powder for fabrication of microcrystal suspension used as a coating material. Scanning electron microscopy (SEM), energy dispersive microanalysis (EDS), energy dispersive x-ray fluorescence (EDXRF) and x-ray diffraction (XRD) were used to characterise the morphology, chemical composition and structure of the coatings. The results showed that the dip coating of stainless steel substrates using viscous solutions lead to the formation of porous calcium phosphate layers. These results suggested that fabrication of bioactive calcium phosphate coatings using this route offers significant advantages over the currently used methods due to considerably lower temperature process involved and may produce better result for substrates with complex shapes

Lar mountain phosphate ore processing using flotation approach

International Nuclear Information System (INIS)

Gharabaghi, M.; Noaparast, M.; Shafaei Tonkaboni, S. Z.

2007-01-01

The sample of Lar Mountain Phosphate deposit which is located in the southwest of Iran, was studied to upgrade its phosphate grade. The results obtained from mineralogical studies showed the presence of apatite, CaO, Al 2 O 3 , Fe 2 O 3 and SiO 2 , in which carbonate was detected as the main gangue. Two sets of direct and reverse flotation tests were performed using samples from this deposit with 10% P 2 O 5 . In phosphate flotation (direct approach), the samples were conditioned with sodium silica, oleic acid-fuel oil and Armac T-fuel oil. The direct flotation at pH=9.2 yielded a product with 23.2% of P 2 O 5 and 75.16% recovery. The reverse flotation tests were carried out at pH=5.2, with floating carbonate and pulp de-oiling, using H 2 SO 4 and wash water, and phosphate was then floated from siliceous gangue. In the second sets of the reverse approach, depressing the phosphate and floating silica with Amines in natural pH were done. However the best concentrate assay was 31.2% P 2 O 5 with a 71.12% recovery, which was obtained from reverse tests

Optimization of calcium phosphate fine ceramic powders preparation

Science.gov (United States)

Sezanova, K.; Tepavitcharova, S.; Rabadjieva, D.; Gergulova, R.; Ilieva, R.

2013-12-01

The effect of biomimetic synthesis method, reaction medium and further precursor treatments on the chemical and phase composition, crystal size and morphology of calcium phosphates was examined. Nanosized calcium phosphate precursors were biomimetically precipitated by the method of continuous precipitation in three types of reaction media at pH 8: (i) SBF as an inorganic electrolyte system; (ii) organic (glycerine) modified SBF (volume ratio of 1:1); (iii) polymer (10 g/l xanthan gum or 10 g/l guar gum) modified SBF (volume ratio of 1:1). After maturation (24 h) the samples were lyophilized, calcinated at 300°C for 3 hours, and washed with water, followed by new gelation, lyophilization and step-wise (200, 400, 600, 800, and 1000°C, each for 3 hours) sintering. The reaction medium influenced the chemical composition and particle size but not the morphology of the calcium phosphate powders. In all studied cases bi-phase calcium phosphate fine powders with well-shaped spherical grains, consisting of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) with a Ca/P ratio of 1.3 - 1.6 were obtained. The SBF modifiers decreased the particle size of the product in the sequence guar gum ˜ xanthan gum < glycerin < SBF medium.

Uranium Extraction from Phosphates: - Background, Opportunities, Process Overview & Way Forward for Commercialisation

International Nuclear Information System (INIS)

Tulsidas, Harikrishnan; Hilton, Julian; Kumar Haldar, Tapan

2014-01-01

Uranium Extraction from Phosphate - an attractive proposition: • Uranium is co-product of phosphate Industry and makes phosphate Industry economically viable & socially more acceptable; • Enable utilisation of mineral deposits having low Phosphate value through economic co-production of Phosphatic fertiliser & Uranium; • Bring new countries in global map of Uranium resources; • Enables socio-economic up-gradation of major part of global population by achieving Energy, food & Environmental security - so important in today’s scenario

Phosphate, urea and creatinine clearances: haemodialysis adequacy assessed by weekly monitoring.

Science.gov (United States)

Debowska, Malgorzata; Wojcik-Zaluska, Alicja; Ksiazek, Andrzej; Zaluska, Wojciech; Waniewski, Jacek

2015-01-01

The specific distribution of phosphate and the control mechanisms for its plasma level makes phosphate kinetics during haemodialysis (HD) considerably different from those of urea and creatinine and makes the quantitative evaluation of adequacy of phosphate removal difficult. We propose the application of equivalent continuous clearance (ECC) as a phosphate adequacy parameter and compare it with ECC for creatinine and urea. Three consecutive dialysis sessions were evaluated for 25 patients on maintenance HD. Concentrations of phosphate, urea and creatinine in plasma were measured every 1h during the treatment and 45 min after, and every 30 min in dialysate. ECC was calculated using the removed solute mass assessed in dialysate and weekly solute profile in plasma. Similar calculations were performed also for the midweek dialysis session only. Different versions of the reference concentration for ECC were applied. ECC with peak average reference concentration was 5.4 ± 1.0 for phosphate, 7.0 ± 1.0 for urea and 4.7 ± 1.0 mL/min for creatinine. ECC for urea and creatinine were well correlated in contrast to the correlations of ECC for phosphate versus urea and creatinine. Midweek ECC were higher than weekly ECC, but they were well correlated for urea and creatinine, but only weakly for phosphate. HD adequacy monitoring for phosphate may be performed using ECC, but it is less predictable than similar indices for urea and creatinine. The values of ECC for phosphate are within the range expected for its molecular size compared with those for urea and creatinine. © The Author 2014. Published by Oxford University Press on behalf of ERA-EDTA. All rights reserved.

Synthesis of β-tricalcium phosphate.

Science.gov (United States)

Chaair, H; Labjar, H; Britel, O

2017-09-01

Ceramics play a key role in several biomedical applications. One of them is bone grafting, which is used for treating bone defects caused by injuries or osteoporosis. Calcium-phosphate based ceramic are preferred as bone graft biomaterials in hard tissue surgery because their chemical composition is close to the composition of human bone. They also have a marked bioresorbability and bioactivity. In this work, we have developed methods for synthesis of β-tricalcium phosphate apatite (β-TCP). These products were characterized by different techniques such as X-ray diffraction, infrared spectroscopy, scanning electron microscopy and chemical analysis. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Development of zirconium/magnesium phosphate composites for immobilization of fission products

International Nuclear Information System (INIS)

Singh, D.; Tlustochowicz, M.; Wagh, A.S.

1999-01-01

Novel chemically bonded phosphate ceramics have been investigated for the capture and stabilization of volatile fission-product radionuclides. The authors have used low-temperature processing to fabricate zirconium phosphate and zirconium/magnesium phosphate composites. A zirconium/magnesium phosphate composite has been developed and shown to stabilize ash waste that has been contaminated with a radioactive surrogate of the 137 Cs and 90 Sr species. Excellent retention of cesium in the phosphate matrix system was observed in both short- and long-term leaching tests. The retention factor determined by the USEPA Toxicity Characteristic Leaching Procedure was one order of magnitude better for cesium that for strontium. The effective diffusivity, at room temperature, for cesium and strontium in the waste forms was estimated to be as low as 2.4 x 10 -13 and 1.2 x 10 -11 m 2 /s, respectively. This behavior was attributed to the capture of cesium in the layered zirconium phosphate structure via an intercalation ion-exchange reaction, followed by microencapsulation. However, strontium is believed to be precipitated out in its phosphate form and subsequently microencapsulated in the phosphate ceramic. The performance of these final waste forms, as indicated by the compression strength and the durability in aqueous environments, satisfies the regulatory criteria

Distinct generation, pharmacology, and distribution of sphingosine 1-phosphate and dihydro-sphingosine 1-phosphate in human neural progenitor cells

Science.gov (United States)

In-vivo and in-vitro studies suggest a crucial role for Sphingosine 1-phosphate (S1P) and its receptors in the development of the nervous system. Dihydrosphingosine 1-phosphate (dhS1P), a reduced form of S1P, is an active ligand at S1P receptors, but the pharmacology and physiology of dhS1P has not...

Stimulation of Suicidal Erythrocyte Death by Increased Extracellular Phosphate Concentrations

Directory of Open Access Journals (Sweden)

Jakob Voelkl

2014-02-01

Full Text Available Background/Aim: Anemia in renal insufficiency results in part from impaired erythrocyte formation due to erythropoietin and iron deficiency. Beyond that, renal insufficiency enhances eryptosis, the suicidal erythrocyte death characterized by phosphatidylserine-exposure at the erythrocyte surface. Eryptosis may be stimulated by increase of cytosolic Ca2+-activity ([Ca2+]i. Several uremic toxins have previously been shown to stimulate eryptosis. Renal insufficiency is further paralleled by increase of plasma phosphate concentration. The present study thus explored the effect of phosphate on erythrocyte death. Methods: Cell volume was estimated from forward scatter, phosphatidylserine-exposure from annexin V binding, and [Ca2+]i from Fluo3-fluorescence. Results: Following a 48 hours incubation, the percentage of phosphatidylserine exposing erythrocytes markedly increased as a function of extracellular phosphate concentration (from 0-5 mM. The exposure to 2 mM or 5 mM phosphate was followed by slight but significant hemolysis. [Ca2+]i did not change significantly up to 2 mM phosphate but significantly decreased at 5 mM phosphate. The effect of 2 mM phosphate on phosphatidylserine exposure was significantly augmented by increase of extracellular Ca2+ to 1.7 mM, and significantly blunted by nominal absence of extracellular Ca2+, by additional presence of pyrophosphate as well as by presence of p38 inhibitor SB203580. Conclusion: Increasing phosphate concentration stimulates erythrocyte membrane scrambling, an effect depending on extracellular but not intracellular Ca2+ concentration. It is hypothesized that suicidal erythrocyte death is triggered by complexed CaHPO4.

Nuclear waste immobilization in iron phosphate glasses

International Nuclear Information System (INIS)

Garcia, D.A.; Rodriguez, Diego A.; Menghini, Jorge E.; Bevilacqua, Arturo

2007-01-01

Iron-phosphate glasses have become important in the nuclear waste immobilization area because they have some advantages over silicate-based glasses, such as a lower processing temperature and a higher nuclear waste load without losing chemical and mechanical properties. Structure and chemical properties of iron-phosphate glasses are determined in terms of the main components, in this case, phosphate oxide along with the other oxides that are added to improve some of the characteristics of the glasses. For example, Iron oxide improves chemical durability, lead oxide lowers fusion temperature and sodium oxide reduces viscosity at high temperature. In this work a study based on the composition-property relations was made. We used different techniques to characterize a series of iron-lead-phosphate glasses with uranium and aluminium oxide as simulated nuclear waste. We used the Arquimedes method to determine the bulk density, differential temperature analysis (DTA) to determine both glass transition temperature and crystallization temperature, dilatometric analysis to calculate the linear thermal expansion coefficient, chemical durability (MCC-1 test) and X-ray diffraction (XRD). We also applied some theoretic models to calculate activation energies associated with the glass transition temperature and crystallization processes. (author)

The antimicrobial activity of as-prepared silver-loaded phosphate glasses and zirconium phosphate

International Nuclear Information System (INIS)

Jing, Wang; Jiang, Ji Zhi; Yang, Yang; Yan, Zhao Chun; Yan, Wang Xiao; He, Shui Zhong

2016-01-01

The antimicrobial activities of silver-loaded zirconium phosphate (JDG) and silver-loaded phosphate glasses (ZZB) against Escherichia coli were studied. Although the silver content in JDG was higher than that in ZZB, ZZB suspensions showed better antimicrobial property than JDG suspensions, especially at low concentrations. The antimicrobial activity was analyzed using minimum inhibitory concentrations, bacterial inhibition ring tests, and detection of silver ions in the suspensions. Furthermore, the amounts of silver ions in suspensions with/without bacterial cells were analyzed. Results revealed that only a portion of released silver ions could be adsorbed by E. coli cells, which are critical to cell death. The damaged microstructures of E. coli cells observed by transmission electron microscopy may further prove that the adsorbed silver ions play an important role in the antimicrobial process.

Interaction between calcium and phosphate adsorption on goethite

NARCIS (Netherlands)

Rietra, R.P.J.J.; Hiemstra, T.; Riemsdijk, van W.H.

2001-01-01

Quantitatively, little is known about the ion interaction processes that are responsible for the binding of phosphate in soil, water, and sediment, which determine the bioavailability and mobility of phosphate. Studies have shown that metal hydroxides are often responsible for the binding of PO4 in

Consortium inoculum of five thermo-tolerant phosphate solubilizing Actinomycetes for multipurpose biofertilizer preparation.

Science.gov (United States)

Nandimath, Arusha P; Karad, Dilip D; Gupta, Shantikumar G; Kharat, Arun S

2017-10-01

Alkaline pH of the soil facilitates the conversion of phosphate present in phosphate fertilizer applied in the field to insoluble phosphate which is not available to plants. Problem of soluble phosphate deficiency arises, primarily due to needless use of phosphate fertilizer. We sought to biofertilizer with the thermo-tolerant phosphate solubilizing actinomycetes consortium that could convert insoluble phosphate to soluble phosphate at wider temperature range. In the present investigation consortium of five thermo-tolerant phosphate solubilizing actinomycetes was applied for preparation of inoculum to produce multipurpose bio-fertilizer. Phosphates solubilizing thermo-tolerant 32 actinomycetes strains were processed for identification with the use of PIBWIN software and were screened for phosphate solubilizing activity. Amongst these five actinomycetes were selected on the basis of their ability to produce cellulase, chitinase, pectinase, protease, lipase, amylase and phosphate solubilizing enzymes. Ability to produce these enzymes at 28°C and 50°C were examined. Biofertilizer was prepared by using agricultural waste as a raw material. While preparation of bio-fertilizer the pH decreased from 7.5 to 4.3 and temperature increased up to 74°C maximum at the end of 4 th week and in subsequent week it started to decline gradually till it reached around 50°C, which was found to be stable up to eighth week. This thermo-tolerant actinomycetes consortium released soluble phosphate of up to 46.7 μg ml -1 . As the mesophilic organisms die out at high temperature of composting hence thormo-tolerant actinomycetes would be the better substitute for preparation of phosphate solubilizing bio-fertilizer with added potential to degrade complex macromolecules in composting.

Origin of Life and the Phosphate Transfer Catalyst

Science.gov (United States)

Piast, Radosław W.; Wieczorek, Rafał M.

2017-03-01

In this paper, we revisit several issues relevant to origin-of-life research and propose a Phosphate Transfer Catalyst hypothesis that furthers our understanding of some of the key events in prebiotic chemical evolution. In the Phosphate Transfer Catalyst hypothesis, we assume the existence of hypothetical metallopeptides with phosphate transfer activity that use abundant polyphosphates as both substrates and energy sources. Nonspecific catalysis by this phosphate transfer catalyst would provide a variety of different products such as phosphoryl amino acids, nucleosides, polyphosphate nucleotides, nucleic acids, and aminoacylated nucleic acids. Moreover, being an autocatalytic set and metabolic driver at the same time, it could possibly replicate itself and produce a collective system of two polymerases; a nucleic acid able to catalyze peptide bond formation and a peptide able to polymerize nucleic acids. The genetic code starts at first as a system that reduces the energy barrier by bringing substrates (2'/3' aminoacyl-nucleotides) together, an ancestral form of the catalysis performed by modern ribosomes.

Inorganic phosphate inhibits sympathetic neurotransmission in canine saphenous veins

International Nuclear Information System (INIS)

Edoute, Y.; Vanhoutte, P.M.; Shepherd, J.T.

1987-01-01

Inorganic phosphate has been proposed as the initiator of metabolic vasodilatation in active skeletal muscle. The present study was primarily designed to determine if this substance has an inhibitory effect on adrenergic neurotransmission. Rings of canine saphenous veins were suspended for isometric tension recording in organ chambers. A comparison was made of the ability of inorganic phosphate (3 to 14 mM) to relax rings contracted to the same degree by electrical stimulation, exogenous norepinephrine, and prostaglandin F/sub 2α/. The relaxation during electrical stimulation was significantly greater at all concentrations of phosphate. In strips of saphenous veins previously incubated with [ 3 H]norepinephrine, the depression of the contractile response caused by phosphate during electrical stimulated was accompanied by a significant reduction in the overflow of labeled neurotransmitter. Thus inorganic phosphate inhibits sympathetic neurotransmission and hence may have a key role in the sympatholysis in the active skeletal muscles during exercise. By contrast, in this preparation, it has a modest direct relaxing action on the vascular smooth muscle

Uranium traps in the phosphate bearing sudr chalk, in northeastern sinai, Egypt

International Nuclear Information System (INIS)

Hussein, H.A.; El-Aassy, I.E.; Mahdy, M.A.; Dabbour, G.A.; Mansour, M.Gh.; Morsy, A.M.

1998-01-01

The maastrichtian sudr formation in northeastern sinai is composed of three members, the lower chalk, the middle phosphate and chart-bearing and the upper chalk members. Lemon yellow secondary uranium mineralization, distributed in the lower chalk member and in some phosphate beds from the middle phosphate member are observed. The XRD analyses of some samples from the uranium bearing chalk and the phosphate beds showed the presence of the secondary uranium minerals carnotite, bergenite and upalite. The mode of uranium occurrences could be interpreted as a result of the phosphatic beds decomposition and their subjection to later diagenetic processes. Uranium leaching circulation from phosphate rocks led to the liberation of uranium from the phosphates, and vanadium from the bituminous material and clay minerals. These migrated and were deposited locally and within the underlying chalk beds which acted as a lithologic trap

Recovery of uranium and the lanthanides from phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Habashi, F; Awadalla, F T; Zailaf, M

1986-06-01

A process is proposed for the treatment of phosphate rock for the recovery of uranium and lanthanides. The process assures the production of phosphatic fertilisers without polluting the environment with radioactive material.

X-ray diffraction studies of chitosan acetate-based polymer electrolytes

International Nuclear Information System (INIS)

Osman, Z.; Ibrahim, Z.A.; Abdul Kariem Arof

2002-01-01

Chitosan is the product when partially deacetylated chitin dissolves in dilute acetic acid. This paper presents the x-ray diffraction patterns of chitosan acetate, plasticised chitosan acetate and plasticised-salted chitosan acetate films. The results show that the chitosan acetate based polymer electrolyte films are not completely amorphous but it is partially crystalline. X-ray diffraction study also confirms the occurrence of the complexation between chitosan and the salt and the interaction between salt and plasticizer. The salt-chitosan interaction is clearly justified by infrared spectroscopy. (Author)

Radiation exposure due to agricultural uses of phosphate fertilizers

International Nuclear Information System (INIS)

Khater, Ashraf E.M.; AL-Sewaidan, H.A.

2008-01-01

Radiological impacts of phosphate rocks mining and manufacture could be significant due to the elevated radioactivity contents of the naturally occurring radioactive materials (NORM), such as 238 U series, 232 Th series and 40 K, in some phosphate deposits. Over the last decades, the land reclamation and agriculture activities in Saudi Arabia and other countries have been widely expanded. Therefore, the usage of chemical fertilizers is increased. Selected phosphate fertilizers samples were collected and the specific activities of NORM were measured using a gamma ray spectrometer based on a hyper pure germanium detector and alpha spectrometer based on surface barrier detector. The obtained results show remarkable wide variations in the radioactivity contents of the different phosphate fertilizer samples. The mean (ranges) of specific activities for 226 Ra, 210 Po, 232 Th and 40 K, and radium equivalent activity are 75 (3-283), 25 (0.5-110), 23 (2-74), 2818 (9-6501) Bq/kg and 283 (7-589) Bq/kg, respectively. Based on dose calculations, the increment of the public radiation exposure due to the regular agricultural usage of phosphate fertilizers is negligible. Its average value 1 m above the ground is about 0.12 nGy/h where the world average value due to the NORM in soil is 51 nGy/h. Direct radiation exposures of the farmers due to phosphate fertilizers application was not considered in our study

Uptake of 15N-labelled urea and 32P-labelled phosphate from acid-based urea phosphate and granular fertilizers

International Nuclear Information System (INIS)

Bole, J.B.

1986-01-01

The availability of nitrogen and phosphorus in fertilizer products labelled with both 32 P and 15 N was measured in a growth chamber experiment. The uptake of N and P by soft white spring wheat (Triticum aestivum L.) from a solution of acid urea phosphate fertilizer did not differ significantly from that of a mixture of granular urea and monammonium phosphate fertilizer. The fertilizer-P uptake efficiency of both sources was higher in a neutral soil than in acid or calcareous soils. Banding either fertilizer increased the uptake of fertilizer P compared with sources mixed with the soil, but did not significantly affect fertilizer-N uptake. The increase in fertilizer-P efficiency due to banding was significantly greater for the urea-monammonium phosphate than for the acid urea phosphate solution. Banding fertilizer did not increase the uptake of fertilizer P in the calcareous soil, and decreased the uptake of fertilizer N in that soil compared with mixed treatments. It is suggested that soluble Ca formed from the reaction of acid with naturally occurring lime may have reduced the availability of fertilizer P in the band

An Arabidopsis thaliana knock-out mutant of the chloroplast triose phosphate/phosphate translocator is severely compromised only when starch synthesis, but not starch mobilisation is abolished

DEFF Research Database (Denmark)

Schneider, Anja; Häusler, Rainer E; Kolukisaoglu, Uner

2002-01-01

The Arabidopsis thaliana tpt-1 mutant which is defective in the chloroplast triose phosphate/phosphate translocator (TPT) was isolated by reverse genetics. It contains a T-DNA insertion 24 bp upstream of the start ATG of the TPT gene. The mutant lacks TPT transcripts and triose phosphate (TP)-spe...

Phosphate adsorption using modified iron oxide-based sorbents

Science.gov (United States)

Phosphate RemovalThis dataset is associated with the following publication:Lalley , J., C. Han , G. RamMohan , T. Speth , J. Garland , M. Nadagouda , and D. Dionysiou. Phosphate Removal using Modified Bayoxide®E33 Adsorption Media. WATER RESEARCH. Elsevier Science Ltd, New York, NY, USA, issue}: 96-107, (2015).

Characterization of iron phosphate glasses prepared by microwave heating

International Nuclear Information System (INIS)

Almeida, Fabio Jesus Moreira de

2006-01-01

Phosphate glasses have been investigated since the fifties, because they are relatively easy to prepare, have low melting temperatures (1000 deg C - 1200 deg C and low glass transition. However, these glasses were very sensitive to humidity, showing a very low chemical durability. Iron phosphate glasses have been prepared by melting inorganic precursors in conventional electric furnaces and induction furnaces. By adding iron, phosphate glasses became chemical resistant and were thought to be used as nuclear waste forms or mechanical resistance fibers. The use of microwaves has been investigated because it makes possible a fast and homogeneous heating of the materials. Microwave promotes the self-heating of the material by the interaction of the external electromagnetic field with the molecules and ions of the material. Niobium phosphate glasses was also produced already through the heating of precursors in microwave ovens. Other glasses containing iron in theirs structure was produced by conventional furnaces and they had your structures analyzed. But even so, it was not still published synthesis of iron phosphate glasses starting from the melting of precursors materials in microwave ovens. In the present work mixtures of (NH 4 ) 2 HPO 4 and Fe 3 O 4 or (NH 4 ) 2 HPO 4 and Fe 2 O 3 were exposed to microwave energy with electromagnetic waves of 2,45 GHz. It was proposed that the absorption of this radiation for the material causes the heating from room temperature to melting temperature. The obtained iron phosphate glasses was analyzed by X-ray diffraction, Moessbauer spectroscopy, and Differential Thermal Analysis. Iron phosphate glasses were also produced in electrical furnaces for comparison. (author)

Characterization of iron phosphate glasses prepared by microwave heating

International Nuclear Information System (INIS)

Almeida, Fabio Jesus Moreira de

2006-01-01

Phosphate glasses have been investigated since the fifties, because they are relatively easy to prepare, have low melting temperatures (1000 deg C - 1200 deg C), and low glass transition. However, these glasses were very sensitive to humidity, showing a very low chemical durability. Iron phosphate glasses have been prepared by melting inorganic precursors in conventional electric furnaces and induction furnaces. By adding iron, phosphate glasses became chemical resistant and were thought to be used as nuclear waste forms or mechanical resistance fibers. The use of microwaves has been investigated because it makes possible a fast and homogeneous heating of the materials. Microwave promotes the self-heating of the material by the interaction of the external electromagnetic field with the molecules and ions of the material. Niobium phosphate glasses was also produced already through the heating of precursors in microwave ovens. Other glasses containing iron in theirs structure was produced by conventional furnaces and they had your structures analyzed. But even so, it was not still published synthesis of iron phosphate glasses starting from the melting of precursors materials in microwave ovens. In the present work mixtures of (NH 4 ) 2 HPO 4 and Fe 3 O 4 or (NH 4 ) 2 HPO 4 and Fe 2 O 3 were exposed to microwave energy with electromagnetic waves of 2,45 GHz. It was proposed that the absorption of this radiation for the material causes the heating from room temperature to melting temperature. The obtained iron phosphate glasses was analyzed by X-ray diffraction, Moessbauer spectroscopy, and Differential Thermal Analysis. Iron phosphate glasses were also produced in electrical furnaces for comparison. (author)

Iron phosphate glasses: Bulk properties and atomic scale structure

Energy Technology Data Exchange (ETDEWEB)

Joseph, Kitheri; Stennett, Martin C.; Hyatt, Neil C.; Asuvathraman, R.; Dube, Charu L.; Gandy, Amy S.; Govindan Kutty, K. V.; Jolley, Kenny; Vasudeva Rao, P. R.; Smith, Roger

2017-10-01

Bulk properties such as glass transition temperature, density and thermal expansion of iron phosphate glass compositions, with replacement of Cs by Ba, are investigated as a surrogate for the transmutation of 137Cs to 137Ba, relevant to the immobilisation of Cs in glass. These studies are required to establish the appropriate incorporation rate of 137Cs in iron phosphate glass. Density and glass transition temperature increases with the addition of BaO indicating the shrinkage and reticulation of the iron phosphate glass network. The average thermal expansion coefficient reduces from 19.8 × 10-6 K-1 to 13.4 × 10-6 K-1, when 25 wt. % of Cs2O was replaced by 25 wt. % of BaO in caesium loaded iron phosphate glass. In addition to the above bulk properties, the role of Ba as a network modifier in the structure of iron phosphate glass is examined using various spectroscopic techniques. The FeII content and average coordination number of iron in the glass network was estimated using Mössbauer spectroscopy. The FeII content in the un-doped iron phosphate glass and barium doped iron phosphate glasses was 20, 21 and 22 ± 1% respectively and the average Fe coordination varied from 5.3 ± 0.2 to 5.7 ± 0.2 with increasing Ba content. The atomic scale structure was further probed by Fe K-edge X-ray absorption spectroscopy. The average coordination number provided by extended X-ray absorption fine structure spectroscopy and X-ray absorption near edge structure was in good agreement with that given by the Mössbauer data.

Radionuclide containment in soil by phosphate treatment

International Nuclear Information System (INIS)

Lee, S.Y.; Francis, C.W.; Timpson, M.E.; Elless, M.P.

1995-01-01

Radionuclide transport from a contaminant source to groundwater and surface water is a common problem faced by most US Department of Energy (DOE) facilities. Containment of the radionuclide plume, including strontium-90 and uranium, is possible using phosphate treatment as a chemical stabilizer. Such a chemical process occurs in soils under natural environmental conditions. Therefore, the concept of phosphate amendment for radiostrontium and uranium immobilization is already a proven principle. In this presentation, results of bench-scale experiments and the concept of a field-scale demonstration are discussed. The phosphate treatment is possible at the source or near the advancing contaminant plume. Cleanup is still the ideal concept; however, containment through stabilization is a more practical and costeffective concept that should be examined by DOE Environmental Restoration programs

Calcium-phosphate-osteopontin particles for caries control

DEFF Research Database (Denmark)

Schlafer, Sebastian

Oftentimes caries lesions develop in protected sites that are difficult to access by self-performed mechanical tooth cleaning. At present, there is a growing interest in chemical adjuncts to mechanical procedures of oral hygiene that aim at biofilm control rather than biofilm eradication. Calcium......-phosphate-osteopontin particles are a new promising therapeutic approach to caries control. They are designed to bind to dental biofilms and interfere with biofilm build-up, lowering the bacterial burden on the tooth surface without affecting bacterial viability in the oral cavity. Moreover, they dissolve when pH in the biofilm...... drops to 6 or below and release buffering phosphate ions that stabilize biofilm pH above the critical level for enamel dissolution. With that twofold approach, calcium-phosphate-osteopontin particles may make a relevant contribution to clinical caries control....

Interfacial Precipitation of Phosphate on Hematite and Goethite

Directory of Open Access Journals (Sweden)

Lijun Wang

2018-05-01

Full Text Available Adsorption and subsequent precipitation of dissolved phosphates on iron oxides, such as hematite and goethite, is of considerable importance in predicting the bioavailability of phosphates. We used in situ atomic force microscopy (AFM to image the kinetic processes of phosphate-bearing solutions interacting with hematite or goethite surfaces. The nucleation of nanoparticles (1.0–4.0 nm in height of iron phosphate (Fe(III-P phases, possibly an amorphous phase at the initial stages, was observed during the dissolution of both hematite and goethite at the earliest crystallization stages. This was followed by a subsequent aggregation stage where larger particles and layered precipitates are formed under different pH values, ionic strengths, and organic additives. Kinetic analysis of the surface nucleation of Fe-P phases in 50 mM NH4H2PO4 at pH 4.5 showed the nucleation rate was greater on goethite than hematite. Enhanced goethite and hematite dissolution in the presence of 10 mM AlCl3 resulted in a rapid increase in Fe-P nucleation rates. A low concentration of citrate promoted the nucleation, whereas nucleation was inhibited at higher concentrations of citrate. By modeling using PHREEQC, calculated saturation indices (SI showed that the three Fe(III-P phases of cacoxenite, tinticite, and strengite may be supersaturated in the reacted solutions. Cacoxenite is predicted to be more thermodynamically favorable in all the phosphate solutions if equilibrium is reached with respect to hematite or goethite, although possibly only amorphous precipitates were observed at the earliest stages. These direct observations at the nanoscale may improve our understanding of phosphate immobilization in iron oxide-rich acid soils.

Phosphatization Associated Features of Ferromanganese Crusts at Lemkein Seamount, Marshall Islands

Science.gov (United States)

Choi, J.; Lee, I.; Park, B. K.; Kim, J.

2014-12-01

Old layers of ferromanganese crusts, especially in the Pacific Ocean, have been affected by phosphatization. Ferromanganese crusts on Lemkein seamount in Marshall Islands also are phosphatized (3.3 to 4.2 wt % of P concentration). Furthermore, they have characteristic features that are different from other ferromanganese crusts. These features occur near the phosphorite, which were thought to fill the pore spaces of ferromanganese crusts. Inside the features, ferromanganese crusts are botryoidally precipitated from the round-boundary. The features of the phosphatized lower crusts of Lemkein seamount are observed using microscope and SEM. Elemental compositions of the selected samples were analyzed by SEM-EDS. Based on the observation and analysis of samples, three characteristic structures are identified: (1) phosphate-filled circles, (2) tongue-shaped framboidal crust, and (3) massive framboidal crust. The phosphate-filled circles are mostly composed of phosphorite, and they include trace fossils such as foraminifera. Phosphatized ferromanganese crusts exist at the boundary of this structure. The tongue-shaped crust is connected with the lips downward, and ferromanganese crusts inside the tongue show distinct growth rim. The massive framboidal crust is located below the tongue. Ferromanganese crusts in the massive framboidal crust are enveloped by phosphate, and some of the crusts are phosphatized. Around the structures, Mn oxide phase is concentrated as a shape of corona on BSE image. All of the structures are in the phosphatized crusts that show columnar growth of ferromanganese crusts and have sub-parallel lamination. These observation and chemical analysis of the ferromanganese crusts can provide a clue of diagenetic processes during the formation of ferromanganese crusts.

Liming effect on P availability from Maardu phosphate rock

International Nuclear Information System (INIS)

Sidlauskas, G.; Masauskas, S.; Ezerinskas, V.

2002-01-01

Thirty years ago phosphate rock from the Maardu deposit was intensively used for soil fertilization in Lithuania. However, the application of finely ground product caused an undesirable dusty operation. Afterwards, a super-phosphate production plant was built in Kedainiai and the use of phosphate rock was completely abandoned. Field experiments with fodder beets and barley were carried out to evaluate the P availability of granulated superphosphate and Maardu phosphate rock. The comparison was made at three acidity levels: a) unlimed acid soil with a high content of Al (pH kcl 4.3-4.4, hydrolytic acidity was 41-44 meq/kg soil), b) soil limed with 0.5n rate CaCO 3 powder limestone based on hydrolytic acidity, and c) soil limed with 1.0n rate CaCO 3 . Two field experiments were carried out with fodder beets. In 1997 the yield increased significantly due to liming. However, no significant yield increases were found due to the application of phosphorus fertilizers. Differences between the effect of superphosphate and phosphate rock were also not observed. This might have been caused by a severe drought during the vegetative growth of plants. In the following year, 1998, a soil with similar acidity was chosen, however it contained even lower amounts of available phosphorus in the arable soil (about 50 mg/kg soil A-L method). In the unlimed soil the yield was low, the effect of superphosphate was better than that of phosphate rock. A good fodder beet yield of 32 to 35 t/ha was obtained and the effect of phosphate rock was better than that of superphosphate at 0.5n CaCO 3 rate. When liming with at the high rate (1.0n CaCO 3 rate according to hydrolytic acidity) the action of phosphate rock declined, and a better yield was obtained with superphosphate. Barley was grown after fodder beets in the 1997 experimental field and the residual effect of superphosphate and phosphate rock was investigated. Weather conditions were favorable for barley growth. Therefore a normal yield

SLC37A1 and SLC37A2 are phosphate-linked, glucose-6-phosphate antiporters.

Directory of Open Access Journals (Sweden)

Chi-Jiunn Pan

Full Text Available Blood glucose homeostasis between meals depends upon production of glucose within the endoplasmic reticulum (ER of the liver and kidney by hydrolysis of glucose-6-phosphate (G6P into glucose and phosphate (P(i. This reaction depends on coupling the G6P transporter (G6PT with glucose-6-phosphatase-α (G6Pase-α. Only one G6PT, also known as SLC37A4, has been characterized, and it acts as a P(i-linked G6P antiporter. The other three SLC37 family members, predicted to be sugar-phosphate:P(i exchangers, have not been characterized functionally. Using reconstituted proteoliposomes, we examine the antiporter activity of the other SLC37 members along with their ability to couple with G6Pase-α. G6PT- and mock-proteoliposomes are used as positive and negative controls, respectively. We show that SLC37A1 and SLC37A2 are ER-associated, P(i-linked antiporters, that can transport G6P. Unlike G6PT, neither is sensitive to chlorogenic acid, a competitive inhibitor of physiological ER G6P transport, and neither couples to G6Pase-α. We conclude that three of the four SLC37 family members are functional sugar-phosphate antiporters. However, only G6PT/SLC37A4 matches the characteristics of the physiological ER G6P transporter, suggesting the other SLC37 proteins have roles independent of blood glucose homeostasis.

Sphingosine 1-phosphate lyase enzyme assay using a BODIPY-labeled substrate

International Nuclear Information System (INIS)

Bandhuvula, Padmavathi; Li Zaiguo; Bittman, Robert; Saba, Julie D.

2009-01-01

Sphingosine 1-phosphate lyase (SPL) is responsible for the irreversible catabolism of sphingosine 1-phosphate, which signals through five membrane receptors to mediate cell stress responses, angiogenesis, and lymphocyte trafficking. The standard assay for SPL activity utilizes a radioactive dihydrosphingosine 1-phosphate substrate and is expensive and cumbersome. In this study, we describe an SPL assay that employs an ω-labeled BODIPY-sphingosine 1-phosphate substrate, allowing fluorescent product detection by HPLC and incorporating advantages of the BODIPY fluorophore. The major aldehyde product is confirmed by reaction with 2,4-dinitrophenylhydrazine. The SPL-catalyzed reaction is linear over a 30 min time period and yields a K m of 35 μM for BODIPY-sphingosine 1-phosphate.

Reaction of Thymidine with Hypobromous Acid in Phosphate Buffer.

Science.gov (United States)

Suzuki, Toshinori; Kitabatake, Akihiko; Koide, Yuki

2016-01-01

When thymidine was treated with hypobromous acid (HOBr) in 100 mM phosphate buffer at pH 7.2, two major product peaks appeared in the HPLC chromatogram. The products in each peak were identified by NMR and MS as two isomers of 5-hydroxy-5,6-dihydrothymidine-6-phosphate (a novel compound) and two isomers of 5,6-dihydroxy-5,6-dihydrothymidine (thymidine glycol) with comparable yields. 5-Hydroxy-5,6-dihydrothymidine-6-phosphate was relatively stable, and decomposed with a half-life of 32 h at pH 7.2 and 37°C generating thymidine glycol. The results suggest that 5-hydroxy-5,6-dihydrothymidine-6-phosphate in addition to thymidine glycol may have importance for mutagenesis by the reaction of HOBr with thymine residues in nucleotides and DNA.

Radiotracer study of phosphate exchange between whey and casein micelles in cow's milk

International Nuclear Information System (INIS)

Kolar, Z.I.; Verburg, T.G.; Dijk, H.J.M. van

1998-01-01

Radiotracer method has been applied to study exchange of calcium ions between the whey calcium salts and micellar calcium phosphate (MCP). The present paper deals with a similar study pertaining to phosphate ions. 32 P-labelled Na 2 HPO 4 was used as the radiotracer for inorganic phosphates of milk. After addition of the radiotracer to skimmed-milk, samples were taken regularly for 700 hours. In the samples casein micelles were separated from whey by ultracentrifugation and finally the radiotracer quantity i.e. 32 P-concentration in the whey samples was measured using a Liquid Scintillation Counter. Compartmental analysis and modelling were used to evaluate the thus obtained time curves for radiotracer quantity in whey. This analysis revealed the presence of three phosphate compartments i.e. exchangeable phosphate entities; one being the whey phosphate. The other two are associated with the exchangeable phosphates of MCP. The mean residence times of phosphate in the latter two compartment differ considerably pointing at two distinctly different embeddings of phosphate groups in the structure of the micellar calcium phosphate of the cow's milk casein. The obtained results are in fair agreement with the mentioned model of MCP

High inorganic phosphate causes DNMT1 phosphorylation and subsequent fibrotic fibroblast activation

Energy Technology Data Exchange (ETDEWEB)

Tan, Xiaoying [Department of Nephrology and Rheumatology, Göttingen University Medical Center, Georg August University, Göttingen (Germany); Department of Cardiology and Pneumology, Göttingen University Medical Center, Georg August University, Göttingen (Germany); Xu, Xingbo [Department of Cardiology and Pneumology, Göttingen University Medical Center, Georg August University, Göttingen (Germany); Zeisberg, Elisabeth M. [Department of Cardiology and Pneumology, Göttingen University Medical Center, Georg August University, Göttingen (Germany); German Center for Cardiovascular Research (DZHK), Göttingen (Germany); Zeisberg, Michael, E-mail: mzeisberg@med.uni-goettingen.de [Department of Nephrology and Rheumatology, Göttingen University Medical Center, Georg August University, Göttingen (Germany); German Center for Cardiovascular Research (DZHK), Göttingen (Germany)

2016-04-08

Phosphate is an essential constituent of critical cellular functions including energy metabolism, nucleic acid synthesis and phosphorylation-dependent cell signaling. Increased plasma phosphate levels are an independent risk factor for lowered life-expectancy as well as for heart and kidney failure. Nevertheless, direct cellular effects of elevated phosphate concentrations within the microenvironment are poorly understood and have been largely neglected in favor of phosphor-regulatory hormones. Because interstitial fibrosis is the common determinant of chronic progressive kidney disease, and because fibroblasts are major mediators of fibrogenesis, we here explored the effect of high extracellular phosphate levels on renal fibroblasts. We demonstrate that high inorganic phosphate directly induces fibrotic fibroblast activation associated with increased proliferative activity, increased expression of α-smooth muscle actin and increased synthesis of type I collagen. We further demonstrate that such fibroblast activation is dependent on phosphate influx, aberrant phosphorylation of DNA methyltransferase DNMT1 and aberrant CpG island promoter methylation. In summary, our studies demonstrate that elevated phosphate concentrations induce pro-fibrotic fibroblast activation independent of phospho-regulatory hormones. - Highlights: • We exposed human kidney fibroblasts to media containing 1 mM or 3 mM phosphate. • Increased phosphate influx causes phosphorylation of DNA methyltransferase Dnmt1. • Phosphorylated Dnmt1 causes promoter methylation and transcriptional silencing of RASAL1. • Depletion of RASAL1 causes increased intrinsic Ras-GTP activity and fibroblast activation. • Inorganic phosphate causes fibroblast activation independent of phospho-regulatory hormones.

Magnesium substitution in the structure of orthopedic nanoparticles: A comparison between amorphous magnesium phosphates, calcium magnesium phosphates, and hydroxyapatites

International Nuclear Information System (INIS)

Nabiyouni, Maryam; Ren, Yufu; Bhaduri, Sarit B.

2015-01-01

As biocompatible materials, magnesium phosphates have received a lot of attention for orthopedic applications. During the last decade multiple studies have shown advantages for magnesium phosphate such as lack of cytotoxicity, biocompatibility, strong mechanical properties, and high biodegradability. The present study investigates the role of Mg +2 and Ca +2 ions in the structure of magnesium phosphate and calcium phosphate nanoparticles. To directly compare the effect of Mg +2 and Ca +2 ions on structure of nanoparticles and their biological behavior, three groups of nanoparticles including amorphous magnesium phosphates (AMPs) which release Mg +2 , calcium magnesium phosphates (CMPs) which release Mg +2 and Ca +2 , and hydroxyapatites (HAs) which release Ca +2 were studied. SEM, TEM, XRD, and FTIR were used to evaluate the morphology, crystallinity, and chemical properties of the particles. AMP particles were homogeneous nanospheres, whereas CMPs were combinations of heterogeneous nanorods and nanospheres, and HAs which contained heterogeneous nanosphere particles. Cell compatibility was monitored in all groups to determine the cytotoxicity effect of particles on studied MC3T3-E1 preosteoblasts. AMPs showed significantly higher attachment rate than the HAs after 1 day and both AMPs and CMPs showed significantly higher proliferation rate when compared to HAs after 7 days. Gene expression level of osteoblastic markers ALP, COL I, OCN, OPN, RUNX2 were monitored and they were normalized to GAPDH housekeeping gene. Beta actin expression level was monitored as the second housekeeping gene to confirm the accuracy of results. In general, AMPs and CMPs showed higher expression level of osteoblastic genes after 7 days which can further confirm the stimulating role of Mg + 2 and Ca +2 ions in increasing the proliferation rate, differentiation, and mineralization of MC3T3-E1 preosteoblasts. - Highlights: • Role of Mg 2+ and Ca 2+ ions in proliferation, and differentiation

Explosion and fire in the uranium trioxide production facilities at the Savannah River Plant on February 12, 1975. A works technical report

International Nuclear Information System (INIS)

McKibben, J.M.

1976-10-01

On February 12, 1975, an explosion and fire occurred in the denitrator room of the separations A-Line facility, resulting in minor injury to two employees and about $230,000 damage to the building and equipment. The facility, which converts uranyl nitrate solution to UO 3 , had operated for 20 years without major accident. Accidental transfer of tributyl phosphate--uranyl nitrate adduct into a denitrator was followed by rapid decomposition of the organic material. Combustible gases were released into the denitrator room and ignited. No contamination was spread outside the facility. A-Line returned to operation August 11, 1975, after equipment and procedures were modified to lower the probability of similar incidents to a very low level. 18 figures, 9 tables

Purex: process and equipment performance

International Nuclear Information System (INIS)

Orth, D.A.

1986-01-01

The Purex process is the solvent extraction system that uses tributyl phosphate as the extractant for separating uranium and plutonium from irradiated reactor fuels. Since the first flowsheet was proposed at Oak Ridge National Laboratory in 1950, the process has endured for over 30 years with only minor modifications. The spread of the technology was rapid, and worldwide use or research on Purex-type processes was reported by the time of the 1955 Geneva Conference. The overall performance of the process has been so good that there are no serious contenders for replacing it soon. This paper presents: process description; equipment performance (mixer-settlers, pulse columns, rapid contactors); fission product decontamination; solvent effects (solvent degradation products); and partitioning of uranium and plutonium

Hydrolysis of TBF and TiAP in presence of zirconium

International Nuclear Information System (INIS)

Vladimirova, M.V.; Kulikov, I.A.; Kuprij, A.A.

1992-01-01

Acid hydrolysis of organic solutions of tributyl phosphate (TBP) and tri-iso-amylphosphate (TiAP) in n-paraffin diluent in the presence of zirconium (0.025-0.1 mole/l) at nitric acid concentration of 0.3-1 mole/l is studied. Hydrolysis of extractants in a two-phase system, modelling conditions of spent fuel reprocessing and consisting of 1.1 mole/l TAP, 3 mole/l nitric acid at zirconium concentration in water phase 0.05-0.11 mole/l, at water-organic phase ratio 10:1 and at 60 deg C is also studied. Constants of TAP hydrolysis in organic and water phases are determined. Mechanism of increasing the TAP hydrolysis rate in zirconium presence is discussed. 5 refs., 2 figs., 5 tabs

Preparation of the pur uranium-metal

International Nuclear Information System (INIS)

Goldschmidt, B.; Vertes, P.

1955-01-01

A detailed description of the chemical processes used to prepare in the factory of Bouchet of the CEA (Seine-Et-Oise) pur metal uranium with either relatively rich ores, or extracts coming of physical or chemical treatment of poor ores. The nitric treatment of ores succeeds to the production of uranate of impure sodium carbonate. This last last product is dissolved in nitric acid and the uranyl nitrate is extracted by tributyl-phosphate diluted in an inert solvent. The uranyl nitrate pure is re-extracted and successively transformed in uranium peroxide, in orange oxide then in brown oxide which is transformed in fluoride by the anhydrous hydrofluoric acid. Uranate fluoride is then reduced in metal by the pure calcium with an yield superior to 99%. (authors) [fr

The solvent extraction of ytterbium from a molten eutectic

International Nuclear Information System (INIS)

Lengyel, T.

1977-01-01

The paper summarizes the results which were obtained in measurements performed with different binary mixtures of solvents being capable of effectively extracting ytterbium from the molten eutectic lithium nitrate--ammonium nitrate. In the course of elaborating the possible ways of extractive separation of rare earths systematic investigations regarding the individual members of the group are required. The binary solvent mixtures consisted of thenoyl-trifluoracetone (TTA), β-isopropil-tropolone (IPT), tributyl phosphate (TBP), di-2-ethylhexyl phosphoric acid (HDEHP), 2,2'-bipyridyl (bipy), dibutyl phtalate (DBP) and Amberlite LA-2 (LA-2). The concentration of the central ion was kept at 5x10 -6 M by using Yb-169 of high specific activity as a tracer for the radiometric assay. (T.I.)

Potentially Prebiotic Syntheses of Condensed Phosphates

Science.gov (United States)

Keefe, Anthony D.; Miller, Stanley L.

1996-01-01

In view of the importance of a prebiotic source of high energy phosphates, we have investigated a number of potentially prebiotic processes to produce condensed phosphates from orthophosphate and cyclic trimetaphosphate from tripolyphosphate. The reagents investigated include polymerizing nitriles, acid anhydrides, lactones, hexamethylene tetramine and carbon suboxide. A number of these processes give substantial yields of pyrophosphate from orthophosphate and trimetaphosphate from tripolyphosphate. Although these reactions may have been applicable in local areas, they are not sufficiently robust to have been of importance in the prebiotic open ocean.

Amorphous calcium phosphate and its application in dentistry

Directory of Open Access Journals (Sweden)

Sun Wei-bin

2011-07-01

Full Text Available Abstract Amorphous Calcium Phosphate (ACP is an essential mineral phase formed in mineralized tissues and the first commercial product as artificial hydroxyapatite. ACP is unique among all forms of calcium phosphates in that it lacks long-range, periodic atomic scale order of crystalline calcium phosphates. The X-ray diffraction pattern is broad and diffuse with a maximum at 25 degree 2 theta, and no other different features compared with well-crystallized hydroxyapatite. Under electron microscopy, its morphological form is shown as small spheroidal particles in the scale of tenths nanometer. In aqueous media, ACP is easily transformed into crystalline phases such as octacalcium phosphate and apatite due to the growing of microcrystalline. It has been demonstrated that ACP has better osteoconductivity and biodegradability than tricalcium phosphate and hydroxyapatite in vivo. Moreover, it can increase alkaline phosphatase activities of mesoblasts, enhance cell proliferation and promote cell adhesion. The unique role of ACP during the formation of mineralized tissues makes it a promising candidate material for tissue repair and regeneration. ACP may also be a potential remineralizing agent in dental applications. Recently developed ACP-filled bioactive composites are believed to be effective anti-demineralizing/remineralizing agents for the preservation and repair of tooth structures. This review provides an overview of the development, structure, chemical composition, morphological characterization, phase transformation and biomedical application of ACP in dentistry.

Characterisation of phosphate rocks at kurun mountain, Sudan

International Nuclear Information System (INIS)

Abdelgader, G. A. M.

2014-08-01

This main objective of this study was to characterise some Sudanese phosphate raw materials collected from Jebel Kurun, located in the eastern part of Nuba Mountain, Western Sudan. The study also aimed to investigate the association between uranium and phosphate and to determine the concentration of some essential elements and trace elements in the phosphate rock. A total of 30 samples were collected from Karun's eastran mountains, near Abujibiha City and have been analyzed for the selected elements using x-ray fluorescence. The obtained results showed that the average concentration of elements was Ca (11.3) and Fe (1.7) as a percentage, while it was Cu (1617.7), Ni (258.4), Pb (185.9), Ti (27.62), V (3779.9), U (160.9), Zn (152.8) and Mn (776.3) in ppm. The average total phosphorus content (analyzed as P O5 %) using UV-visible spectrometer was found to be 30.54%. This could be considered is acceptable percentage for phosphate to be 30.54%. This could be considered is acceptable percentage for phosphate to be used in industrial fertilizers and phosphoric acid production. The average total calcium carbonate was 15.7%. For the elements distribution, uranium found to be more concentrated in the summit of Jebel Kurun, and it displayed a correlation with lead. Furthermore, four groups of association have been noticed, based on elements concentrations.(Author)

Overexpression of Thellungiella halophila H+-pyrophosphatase Gene Improves Low Phosphate Tolerance in Maize

Science.gov (United States)

Pei, Laming; Wang, Jiemin; Li, Kunpeng; Li, Yongjun; Li, Bei; Gao, Feng; Yang, Aifang

2012-01-01

Low phosphate availability is a major constraint on plant growth and agricultural productivity. Engineering a crop with enhanced low phosphate tolerance by transgenic technique could be one way of alleviating agricultural losses due to phosphate deficiency. In this study, we reported that transgenic maize plants that overexpressed the Thellungiella halophila vacuolar H+-pyrophosphatase gene (TsVP) were more tolerant to phosphate deficit stress than the wild type. Under phosphate sufficient conditions, transgenic plants showed more vigorous root growth than the wild type. When phosphate deficit stress was imposed, they also developed more robust root systems than the wild type, this advantage facilitated phosphate uptake, which meant that transgenic plants accumulated more phosphorus. So the growth and development in the transgenic maize plants were not damaged as much as in the wild type plants under phosphate limitation. Overexpression of TsVP increased the expression of genes involved in auxin transport, which indicated that the development of larger root systems in transgenic plants might be due in part to enhanced auxin transport which controls developmental events in plants. Moreover, transgenic plants showed less reproductive development retardation and a higher grain yield per plant than the wild type plants when grown in a low phosphate soil. The phenotypes of transgenic maize plants suggested that the overexpression of TsVP led to larger root systems that allowed transgenic maize plants to take up more phosphate, which led to less injury and better performance than the wild type under phosphate deficiency conditions. This study describes a feasible strategy for improving low phosphate tolerance in maize and reducing agricultural losses caused by phosphate deficit stress. PMID:22952696

Removal of Phosphate from Synthetic Aqueous Solution by Adsorption with Dolomite from Padalarang

Directory of Open Access Journals (Sweden)

Fadjari Lucia Nugroho

2014-12-01

Full Text Available The presence of phosphate in wastewaters can cause eutrophication of surface water bodies leading to algal-blooming in the aquatic environment and degradation of water quality. Phosphate removal from wastewaters by conventional biological treatment removes only 10-30% of the phosphate, whilst chemical treatment using precipitants such as calcium or iron salts, although effective, is expensive and produces water-rich sludge which must be further treated. Hence, phosphate removal by adsorption in the form of Ca -phosphate has been proposed as an alternative to the more traditional methods. This study investigated the feasibility of using dolomite–a common sedimentary rock–from Padalarang, West Java, Indonesia as the adsorbent for the removal of phosphate from synthetic aqueous solution. Chemical analysis revealed that the Padalarang dolomite contains 33.6-36.2% CaO. Batch experiments at room temperature indicated that optimum removal of phosphate was achieved at pH 9. At 25°C , where increasing concentrations of phosphate (10–100 mg/L increased phosphate adsorption (2.15-31.3 mg/g by the dolomite. The adsorption of phosphate could be described by the Langmuir isotherm model, with constants Qm= 476.19 mg/g, K L= 0,00106 L/mg and equilibrium parameter (R L: 0.904 – 0.989. Phosphate adsorption by dolomite not only permits its removal but also its potential recovery for reuse.

Advances in process technology for eco-friendly phosphates by separation of radionuclides

Energy Technology Data Exchange (ETDEWEB)

Singh, H; Mukherjee, T K [Uranium and Rare Earths Extraction Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Phosphates are used in the industry for fertilizers, industrial chemicals (detergents, water-treatment chemicals) and food-additives. The source of phosphates for the industry is rock-phosphate. Over 90% of phosphate rocks of the world are associated with uranium and its radioactive daughter products. Processing and use of phosphates is accompanied by radiation hazards. The concentration of radionuclides is low, but in view of large number of persons exposed to the hazards, the cumulative societal pollution load is high, and a matter of concern for international organisations. Chemical engineering techniques have been developed for the reduction of societal radiation hazard from the phosphates. In this paper, brief details of the process and developmental efforts in India are described. (author). 4 refs., 1 fig.

Obtaining tetracalcium phosphate and hydroxyapatite in powder form by wet method

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Sara Verusca de; Fook, Marcus Vinicius Lia; Araujo, Elaine Patricia; Medeiros, Keila Machado; Rabello, Guilherme Portela; Barbosa Renata; Araujo, Edcleide Maria, E-mail: saraveruscadeoliveira@yahoo.com.br, E-mail: marcusvinicius@dema.ufcg.edu.br, E-mail: elainepatriciaaraujo@yahoo.com.br, E-mail: keilamm@ig.com.br, E-mail: guilhermeportel@hotmail.com, E-mail: rrenatabarbosa@yahoo.com, E-mail: edcleide@dema.ufcg.edu.br [Universidade Federal de Campina Grande (UAEMa/CCT/UFCG), Campina Grande, PB (Brazil)

2009-07-01

The development of research in the area of advanced materials and tissue engineering has increased greatly in recent years found that bioceramics are outstanding in the replacement and regeneration of bone tissue, mainly formed by the calcium phosphate ceramics. The objective of this research is to obtain the calcium phosphate where Ca/P = 1.67 and 2.0, to observe the formation of phases after having subjected these materials to heat treatment. The calcium phosphate was produced by the wet method using a direct reaction of neutralization and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray microanalysis (EDS). The XRD results confirm the presence of hydroxyapatite phase in the sample with Ca/P = 1.67, whereas the phosphates prepared with Ca/P = 2.0 ratio show a combination of hydroxyapatite and phase β- tricalcium phosphate. The micrographs obtained are characteristic of ceramic material called calcium phosphate. EDS confirmed the presence of Ca, P and O in the material. (author)

Obtaining tetracalcium phosphate and hydroxyapatite in powder form by wet method

International Nuclear Information System (INIS)

Oliveira, Sara Verusca de; Fook, Marcus Vinicius Lia; Araujo, Elaine Patricia; Medeiros, Keila Machado; Rabello, Guilherme Portela; Barbosa Renata; Araujo, Edcleide Maria

2009-01-01

The development of research in the area of advanced materials and tissue engineering has increased greatly in recent years found that bioceramics are outstanding in the replacement and regeneration of bone tissue, mainly formed by the calcium phosphate ceramics. The objective of this research is to obtain the calcium phosphate where Ca/P = 1.67 and 2.0, to observe the formation of phases after having subjected these materials to heat treatment. The calcium phosphate was produced by the wet method using a direct reaction of neutralization and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and X-ray microanalysis (EDS). The XRD results confirm the presence of hydroxyapatite phase in the sample with Ca/P = 1.67, whereas the phosphates prepared with Ca/P = 2.0 ratio show a combination of hydroxyapatite and phase β- tricalcium phosphate. The micrographs obtained are characteristic of ceramic material called calcium phosphate. EDS confirmed the presence of Ca, P and O in the material. (author)

Increased serum phosphate concentrations in patients with advanced chronic kidney disease treated with diuretics.

Science.gov (United States)

Caravaca, Francisco; García-Pino, Guadalupe; Martínez-Gallardo, Rocío; Ferreira-Morong, Flavio; Luna, Enrique; Alvarado, Raúl; Ruiz-Donoso, Enrique; Chávez, Edgar

2013-01-01

Serum phosphate concentrations usually show great variability in patients with advanced chronic kidney disease (ACKD) not on dialysis. Diuretics treatment can have an influence over the severity of mineral-bone metabolism alterations related to ACKD, but their effect on serum phosphate levels is less known. This study aims to determine whether diuretics are independently associated with serum phosphate levels, and to investigate the mechanisms by which diuretics may affect phosphate metabolism. 429 Caucasian patients with CKD not on dialysis were included in this cross-sectional study. In addition to conventional serum biochemical measures, the following parameters of renal phosphate excretion were assessed: 24-hours urinary phosphate excretion, tubular maximum phosphate reabsorption (TmP), and fractional excretion of phosphate (FEP). 58% of patients were on treatment with diuretics. Patients on diuretics showed significantly higher mean serum phosphate concentration (4.78 ± 1.23 vs. 4.24 ± 1.04 mg/dl; Pdiuretics. By multivariate linear and logistic regression, significant associations between diuretics and serum phosphate concentrations or hyperphosphataemia remained after adjustment for potential confounding variables. In patients with the highest phosphate load adjusted to kidney function, those treated with diuretics showed significantly lower FEP than those untreated with diuretics. Treatment with diuretics is associated with increased serum phosphate concentrations in patients with ACKD. Diuretics may indirectly interfere with the maximum renal compensatory capacity to excrete phosphate. Diuretics should be considered in the studies linking the relationship between serum phosphate concentrations and cardiovascular alterations in patients with CKD.

Preparation and bioactivity of micro-arc oxidized calcium phosphate coatings

International Nuclear Information System (INIS)

Pan, Y.K.; Chen, C.Z.; Wang, D.G.; Lin, Z.Q.

2013-01-01

Calcium phosphate (CaP) coatings were prepared on ZK60 magnesium alloy by micro-arc oxidation (MAO) in electrolyte containing calcium acetate monohydrate (CH 3 COO) 2 Ca·H 2 O) and disodium hydrogen phosphate dodecahydrate (Na 2 HPO 4 ·12H 2 O). Scanning electron microscope (SEM), energy-dispersive X-ray spectrometry (EDX) and X-ray diffractometer (XRD) were employed to characterize the microstructure, elemental distribution and phase composition of the CaP coatings respectively. Simulated body fluid (SBF) immersion test was used to evaluate the coating degradability and bioactivity. After 30 days of SBF immersion, the CaP coatings effectively reduce the degradation rate. The surfaces of CaP coatings are covered by a new layer formed of numerous needle-like, spherical and columned calcium phosphates. SEM, EDX and XRD results suggest that these calcium phosphates are bioactive calcium phosphate phases such as hydroxyapatite (Ca 10 (PO 4 ) 6 (OH) 2 , HA) and calcium pyrophosphates (Ca 2 P 2 O 7 , CPP). The formation of these calcium phosphates indicates that the CaP coatings have bioactivity. - Highlights: • Bioactive CaP coatings are successfully formed on ZK60 magnesium alloy. • CaP coatings consist of MgO, MgF 2 , CaO, CaF 2 and Ca 3 (PO 4 ) 2 . • Needle-like, spherical and columned calcium phosphates formed in SBF. • CaP coatings exhibit bioactivity and low corrosion rate

Allergic contact dermatitis from sodium dihydroxycetyl phosphate, a new cosmetic allergen?

DEFF Research Database (Denmark)

Lomholt, H; Rastogi, S C; Andersen, Klaus Ejner

2001-01-01

Sodium dihydroxycetyl phosphate (trade name Dragophos S 2/918501) was identified as a contact allergen in a herbal moisturizing cream causing severe acute contact dermatitis on the hands and face of a 41-year-old woman. Sodium dihydroxycetyl phosphate is a complex mixture of phosphate esters of d...

Phosphate-mediated electrochemical adsorption of cisplatin on gold electrodes

International Nuclear Information System (INIS)

Kolodziej, Adam; Figueiredo, Marta C.; Koper, Marc T.M.; Fernandez-Trillo, Francisco; Rodriguez, Paramaconi

2017-01-01

Highlights: •The potential-dependent adsorption and deposition of cisplatin on polycrystalline gold electrode is mediated by the adsorption of phosphate anions on gold electrode. •Quantitative analysis suggests that the stoichiometry of the phosphate species and the cisplatin adsorbed was 1:1. •Upon reduction of the phosphate-mediated cisplatin adsorption, the platinum deposits are formed by 3D nanoclusters -- Abstract: This manuscript reports the potential-dependent adsorption and deposition of cisplatin on polycrystalline gold electrode. It was found that this process is mediated by the adsorption of phosphate anions on the gold electrode and that the maximum coverage of Pt adsorbed is given by the maximum coverage of phosphate adsorbed at a given potential. The interaction of cisplatin with the phosphate groups was confirmed by in situ FTIR spectroscopy under external reflexion configuration. Quantitative analysis suggests that the stoichiometry of the phosphate species and the cisplatin adsorbed was 1:1. Moreover, the relationship between the charge of the Pt deposited and the charge of the electrochemical surface area of the Pt deposited on the gold electrodes indicates that 3D nanoclusters of a few atoms of Pt were formed over the gold electrode upon the electrochemical reduction of the adsorbed cisplatin. The Pt nanoclusters formed under these conditions were later evaluated for the oxidation of a monolayer of carbon monoxide. The Pt nanoclusters showed a high overpotential for the oxidation of the carbon monoxide monolayer and the high oxidation overpotential was attributed to the absence of adsorption sites for OH species on the Pt clusters: only at potentials where the OH species are adsorbed at the edge between the Pt nanocluster and the gold support, the oxidation of the carbon monoxide on the Pt nanoparticles takes place.

Inhibition of calcium phosphate precipitation under environmentally-relevant conditions

International Nuclear Information System (INIS)

Cao Xinde; Harris, Willie G.; Josan, Manohardeep S.; Nair, Vimala D.

2007-01-01

Precipitation of Ca phosphates plays an important role in controlling P activity and availability in environmental systems. The purpose of this study was to determine inhibitory effects on Ca phosphate precipitation by Mg 2+ , SO 4 2- , CO 3 2- , humic acid, oxalic acid, biogenic Si, and Si-rich soil clay commonly found in soils, sediments, and waste streams. Precipitation rates were determined by measuring decrease of P concentration in solutions during the first 60 min; and precipitated solid phases identified using X-ray diffraction and electron microscopy. Poorly-crystalline hydroxyapatite (HAP: Ca 5 (PO 4 ) 3 OH) formed in control solutions over the experiment period of 24 h, following a second-order dependence on P concentration. Humic acid and Mg 2+ significantly inhibited formation of HAP, allowing formation of a more soluble amorphous Ca phosphate phase (ACP), and thus reducing the precipitation rate constants by 94-96%. Inhibition caused by Mg 2+ results from its incorporation into Ca phosphate precipitates, preventing formation of a well-crystalline phase. Humic acid likely suppressed Ca phosphate precipitation by adsorbing onto the newly-formed nuclei. Presence of oxalic acid resulted in almost complete inhibition of HAP precipitation due to preemptive Ca-oxalate formation. Carbonate substituted for phosphate, decreasing the crystallinity of HAP and thus reducing precipitation rate constant by 44%. Sulfate and Si-rich solids had less impact on formation of HAP; while they reduced precipitation in the early stage, they did not differ from the control after 24 h. Results indicate that components (e.g., Mg 2+ , humic acid) producing relatively soluble ACP are more likely to reduce P stability and precipitation rate of Ca phosphate in soils and sediments than are components (e.g., SO 4 2- , Si) that have less effect on the crystallinity

PHOSPHATES REMOVAL FROM REJECT WATER FROM DIGESTION OF SLUDGE

Directory of Open Access Journals (Sweden)

Elżbieta Sperczyńska

2016-06-01

Full Text Available The aim of the research work was to evaluate if coagulants used on technical scale are useful in phosphates removal from reject water. Effectiveness of phosphorus compounds removal from reject water from digestion of sewage sludge was examined. Selected prehydrolysed alkaline aluminium polychlorides were used. The results were compared to the ones obtained with aluminium sulphate. Reject water from digestion of sewage sludge form WWTP of 100 000 PE were examined. Commercial agents – prehydrolysed PAX 18, PAX XL10, PAX-XL1905 as well as aluminium sulphate were used. Various doses of coagulants: 0.7; 1.0; 1.5 – time higher than stoichiometric dose were applied. Stoichiometric dose was calculated based on chemical reaction of insoluble aluminium phosphate formation. Concentrations of Kiejdahl nitrogen (891 mgNKj/dm3, phosphates (125 mgPO43-/dm3 and organic compounds - COD (592 mgO2/dm3 in reject water were very high. The effectiveness of coagulation process increased as the doses of chemical agents increased. The most effective doses were the highest ones used during the experiment. The most effective agent was PAX 18 (96% removal efficiency. As the phosphates concentration decreased COD content declined simultaneously. Maximum COD removal (47% was obtained when highly alkaline PAX XL 1905 was used. Use of the lowest dose of Al2(SO43 allowed for 50% phosphates removal, whereas the lowest dose of PAX 18 decreased phosphates concentration by 83%.

Procedure for the separation of cerium from crude phosphates and rare earth concentrates

International Nuclear Information System (INIS)

Richter, H.; Koenig, O.; Schmitt, A.; Grauss, H.; Freitag, S.

1986-01-01

The invention has to do with a procedure for the separation of cerium from crude phosphates and rare earth phosphate concentrates originating from the partial neutralization of nitric crude phosphate decomposition solutions. It is aimed at the cerium separation from the raw material at an early stage of reprocessing without preceding elimination of other components and impurities. The rare earth phosphate concentrates or crude phosphates are dissolved in nitric acid, the Ce 3+ is oxidized with potassium permanganate or magnanese(IV) hydroxide, and cerium(IV) phosphate is precipitated as pure substance by decreasing the acidity of the solution

Enhanced phosphate selectivity from wastewater using copper-loaded chelating resin functionalized with polyethylenimine.

Science.gov (United States)

An, Byungryul; Nam, Juhee; Choi, Jae-Woo; Hong, Seok-Won; Lee, Sang-Hyup

2013-11-01

In water and wastewater, phosphate is considered a critical contaminant due to cause algae blooms and eutrophication. To meet the stringent regulation of phosphate in water, a new commercial chelating resin functionalized with polyethylenimine was tested for phosphate removal by loading Cu(2+) and Fe(2+)/Fe(3+) to enhance selectivity for phosphate. Batch and column experiments showed that CR20-Cu exhibited high selectivity for phosphate over other strong anions such as sulfate. The average binary phosphate/nitrate and phosphate/sulfate factors for CR20-Cu were calculated to be 7.3 and 4.8, respectively, which were more than 0.97 and 0.22 for a commercial anion exchanger (AMP16). The optimal pH for the phosphate removal efficiency was determined to be 7. According to the fixed-bed column test, the breakthrough sequence for multiple ions was HPO4(2-)>SO4(2-)>NO3(-)>Cl(-). Saturated CR20-Cu can be regenerated using 4% NaCl at pH 7. More than 95% of the phosphate from CR20-Cu was recovered, and the phosphate uptake capacity for CR20-Cu was not reduced after 7 regeneration cycles. Copyright © 2013 Elsevier Inc. All rights reserved.

Phosphate homeostasis in Bartter syndrome: a case-control study.

Science.gov (United States)

Bettinelli, Alberto; Viganò, Cristina; Provero, Maria Cristina; Barretta, Francesco; Albisetti, Alessandra; Tedeschi, Silvana; Scicchitano, Barbara; Bianchetti, Mario G

2014-11-01

Bartter patients may be hypercalciuric. Additional abnormalities in the metabolism of calcium, phosphate, and calciotropic hormones have occasionally been reported. The metabolism of calcium, phosphate, and calciotropic hormones was investigated in 15 patients with Bartter syndrome and 15 healthy subjects. Compared to the controls, Bartter patients had significantly reduced plasma phosphate {mean [interquartile range]:1.29 [1.16-1.46] vs. 1.61 [1.54-1.67] mmol/L} and maximal tubular phosphate reabsorption (1.16 [1.00-1.35] vs. 1.41 [1.37-1.47] mmol/L) and significantly increased parathyroid hormone (PTH) level (6.1 [4.5-7.7] vs. 2.8 [2.2-4.4] pmol/L). However, patients and controls did not differ in blood calcium, 25-hydroxyvitamin D, alkaline phosphatase, and osteocalcin levels. In patients, an inverse correlation (P Bartter patients.

Development of chemically engineered porous metal oxides for phosphate removal

International Nuclear Information System (INIS)

Delaney, Paul; McManamon, Colm; Hanrahan, John P.; Copley, Mark P.; Holmes, Justin D.; Morris, Michael A.

2011-01-01

In this study, the application of ordered mesoporous silica (OMS) doped with various metal oxides (Zr, Ti, Fe and Al) were studied for the removal of (ortho) phosphate ions from water by adsorption. The materials were characterized by means of N 2 physisorption (BET), powder X-ray diffraction (PXRD) and transmission electron microscopy (TEM). The doped materials had surface areas between 600 and 700 m 2 g -1 and exhibited pore sizes of 44-64 A. Phosphate adsorption was determined by measurement of the aqueous concentration of orthophosphate using ultraviolet-visible (UV-vis) spectroscopy before and after extraction. The effects of different metal oxide loading ratios, initial concentration of phosphate solution, temperature and pH effects on the efficiency of phosphate removal were investigated. The doped mesoporous materials were effective adsorbents of orthophosphate and up to 100% removal was observed under appropriate conditions. 'Back extracting' the phosphate from the doped silica (following water treatment) was also investigated and shown to have little adverse effect on the adsorbent.

Calcium phosphate saturation in the western Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Naik, S.; Reddy, C.V.G.

Temperature, inorganic phosphate concentration and pH seem to be the major factors influencing the degree of saturation of calcium phosphate in sea water. Two water regions can be demarcated in the study area based on the saturation patterns...

Atomic structure of intracellular amorphous calcium phosphate deposits.

Science.gov (United States)

Betts, F; Blumenthal, N C; Posner, A S; Becker, G L; Lehninger, A L

1975-06-01

The radial distribution function calculated from x-ray diffraction of mineralized cytoplasmic structures isolated from the hepatopancreas of the blue crab (Callinectes sapidus) is very similar to that previously found for synthetic amorphous calcium phosphate. Both types of mineral apparently have only short-range atomic order, represented as a neutral ion cluster of about 10 A in longest dimension, whose probable composition is expressed by the formula Ca9(PO4)6. The minor differences observed are attributed to the presence in the biological mineral of significant amounts of Mg-2+ and ATP. Synthetic amorphous calcium phosphate in contact with a solution containing an amount of ATP equivalent to that of the biological mineral failed to undergo conversion to the thermodynamically more stable hydroxyapatite. The amorphous calcium phosphate of the cytoplasmic mineral granules is similarly stable, and does not undergo conversion to hydroxyapatite, presumably owing to the presence of ATP and Mg-2+, known in inhibitors of the conversion process. The physiological implications of mineral deposits consisting of stabilized calcium phosphate ion clusters are discussed.

40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under this...

Biphasic products of dicalcium phosphate-rich cement with injectability and nondispersibility

International Nuclear Information System (INIS)

Ko, Chia-Ling; Chen, Jian-Chih; Hung, Chun-Cheng; Wang, Jen-Chyan; Tien, Yin-Chun; Chen, Wen-Cheng

2014-01-01

In this study, a calcium phosphate cement was developed using tetracalcium phosphate and surface-modified dicalcium phosphate anhydrous (DCPA). This developed injectable bone graft substitute can be molded to the shape of the bone cavity and set in situ through the piping system that has an adequate mechanical strength, non-dispersibility, and biocompatibility. The materials were based on the modified DCPA compositions of calcium phosphate cement (CPC), where the phase ratio of the surface-modified DCPA is higher than that of the conventional CPC for forming dicalcium phosphate (DCP)-rich cement. The composition and morphology of several calcium phosphate cement specimens during setting were analyzed via X-ray diffractometry and transmission electron microscopy coupled with an energy dispersive spectroscopy system. The compressive strength of DCP-rich CPCs was greater than 30 MPa after 24 h of immersion in vitro. The reaction of the CPCs produced steady final biphasic products of DCPs with apatite. The composites of calcium phosphate cements derived from tetracalcium phosphate mixed with surface-modified DCPA exhibited excellent mechanical properties, injectability, and interlocking forces between particles, and they also featured nondispersive behavior when immersed in a physiological solution. - Highlights: • Bone cement precursor with nanocrystals is characterized. • DCP-rich CPCs with nanocrystals exhibited biphasic product phases. • Nanocrystals in cement significantly affected the interlocking ability. • Nanocrystals in cement exhibited higher strength and anti-dispersion. • DCP-rich CPCs increase the potential of bioresorption after reaction

Phosphate binding therapy in dialysis patients: focus on lanthanum carbonate

Directory of Open Access Journals (Sweden)

Ismail A Mohammed

2008-11-01

Full Text Available Ismail A Mohammed, Alastair J HutchisonManchester Institute of Nephrology and Transplantation, Manchester Royal Infirmary, Oxford Road, Manchester, UKAbstract: Hyperphosphatemia is an inevitable consequence of end stage chronic kidney disease and is present in the majority of dialysis patients. Recent observational data has associated hyperphosphatemia with increased cardiovascular mortality among dialysis patients. Dietary restriction of phosphate and current dialysis prescription practices are not enough to maintain serum phosphate levels within the recommended range so that the majority of dialysis patients require oral phosphate binders. Unfortunately, conventional phosphate binders are not reliably effective and are associated with a range of limitations and side effects. Aluminium-containing agents are highly efficient but no longer widely used because of well established and proven toxicity. Calcium based salts are inexpensive, effective and most widely used but there is now concern about their association with hypercalcemia and vascular calcification. Sevelamer hydrochloride is associated with fewer adverse effects, but a large pill burden and high cost are limiting factors to its wider use. In addition, the efficacy of sevelamer as a monotherapy in lowering phosphate to target levels in severe hyperphosphatemia remains debatable. Lanthanum carbonate is a promising new non-aluminium, calcium-free phosphate binder. Preclinical and clinical studies have demonstrated a good safety profile, and it appears well tolerated and effective in reducing phosphate levels in dialysis patients. Its identified adverse events are apparently mild to moderate in severity and mostly GI related. It appears to be effective as a monotherapy, with a reduced pill burden, but like sevelamer, it is significantly more expensive than calcium-based binders. Data on its safety profile over 6 years of treatment are now available.Keywords: hyperphosphatemia, lanthanum

Phosphate phosphors for solid-state lighting

Energy Technology Data Exchange (ETDEWEB)

Shinde, Kartik N. [N.S. Science and Arts College, Bhadrawati (India). Dept. of Physics; Swart, H.C. [University of the Orange Free State, Bloemfontein (South Africa). Dept. of Physics; Dhoble, S.J. [R.T.M. Nagpur Univ. (India). Dept. of Physics; Park, Kyeongsoon [Sejong Univ., Seoul (Korea, Republic of). Faculty of Nanotechnology and Advanced Materials Engineering

2012-07-01

Essential information for students in researchers working towards new and more efficient solid-state lighting. Comprehensive survey based on the authors' long experience. Useful both for teaching and reference. The idea for this book arose out of the realization that, although excellent surveys and a phosphor handbook are available, there is no single source covering the area of phosphate based phosphors especially for lamp industry. Moreover, as this field gets only limited attention in most general books on luminescence, there is a clear need for a book in which attention is specifically directed toward this rapidly growing field of solid state lighting and its many applications. This book is aimed at providing a sound introduction to the synthesis and optical characterization of phosphate phosphor for undergraduate and graduate students as well as teachers and researchers. The book provides guidance through the multidisciplinary field of solid state lighting specially phosphate phosphors for beginners, scientists and engineers from universities, research organizations, and especially industry. In order to make it useful for a wide audience, both fundamentals and applications are discussed, together.

Silane surface modification effects on the electromagnetic properties of phosphatized iron-based SMCs

Science.gov (United States)

Fan, Liang-Fang; Hsiang, Hsing-I.; Hung, Jia-Jing

2018-03-01

It is difficult to achieve homogeneous phosphatized iron powder dispersion in organic resins during the preparation of soft magnetic composites (SMCs). Inhomogeneous iron powder mixing in organic resins generally leads to the formation of micro-structural defects in SMCs and hence causes the magnetic properties to become worse. Phosphatized iron powder dispersion in organic resins can be improved by coating the phosphatized iron powder surfaces with a coupling agent. This study investigated the (3-aminopropyl) triethoxysilane (APTES) surface modification effects on the electromagnetic properties of phosphatized iron-based soft magnetic composites (SMCs). The results showed that the phosphatized iron powder surface can be modified using APTES to improve the phosphatized iron powder and epoxy resin compatibility and hence enhance phosphate iron powder epoxy mixing. The tensile strength, initial permeability, rated current under DC-bias superposition and magnetic loss in SMCs prepared using phosphatized iron powders can be effectively improved using APTES surface modification, which provides a promising candidate for power chip inductor applications.

Effect of molybdate on phosphating of Nd-Fe-B magnets for corrosion protection

Directory of Open Access Journals (Sweden)

Adonis Marcelo Saliba-Silva

2005-06-01

Full Text Available Nd-Fe-B magnets are highly susceptible to corrosion and need protection against environment attack. The use of organic coatings is one of the main methods of corrosion protection of these materials. Data related to the effect of conversion coatings, such as phosphating, on corrosion performance of these magnets is still scarce. Studies about the effect of phosphating on the corrosion resistance of a commercial Nd-Fe-B sintered magnet indicated that it increases the corrosion resistance of these magnets, compared to non-phosphated magnets. In this study, the solution chemistry of a phosphating bath was altered with the addition of molybdate and its effect on the corrosion resistance of magnets investigated. Sintered magnet specimens were phosphated in solutions of 10 g/L NaH2PO4 (pH 3.8, either with or without molybdate [10-3 M MoO4(2-], to improve their corrosion resistance. The effect of phosphating time was also evaluated, and specimens were phosphated for 4 and 18 hours. To evaluate the corrosion performance of phosphated and unphosphated specimens, a corrosion test based on monitoring hydrogen evolution on the surface of the magnets was used. This technique revealed that the addition of molybdate to the phosphating solution improved the corrosion resistance of the magnets phosphated by immersion for short periods but had no beneficial effect if phosphated by immersion for longer periods.

Calcium phosphate saturation in seawater around the Andaman Island

Digital Repository Service at National Institute of Oceanography (India)

Naik, S.; Reddy, C.V.G.

Ionic product (IP) of calcium phosphate is calculated at some stations around Andaman Island. The depthwise variations of the ionic product of calcium phosphate seem to follow a normal trend with maximum saturation value between 100 to 200 m. Using...

Uranium determination in phosphatized materials by drop electrode polarography

International Nuclear Information System (INIS)

Sequeira, F.M.C. de; Abrao, A.

1987-01-01

An uranium determination procedure in phosphate rocks and crude phosphoric acid is outlined polarography is used. Uranium is previously separedted by extraction with tri-n-byte phosphate 10%-petroleum ether using aluminium nitrate as salting out agent. (M.L.J.) [pt

Characterization, Leaching, and Filtration Testing for Bismuth Phosphate Sludge (Group 1) and Bismuth Phosphate Saltcake (Group 2) Actual Waste Sample Composites

International Nuclear Information System (INIS)

Lumetta, Gregg J.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn; Edwards, Matthew K.; Fiskum, Sandra K.; Hallen, Richard T.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Shimskey, Rick W.; Sinkov, Sergey I.; Snow, Lanee A.

2009-01-01

A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan.() The test program was subdivided into logical increments. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. The actual waste-testing program included homogenizing the samples by group, characterizing the solids and aqueous phases, and performing parametric leaching tests. Two of the eight defined groups - bismuth phosphate sludge (Group 1) and bismuth phosphate saltcake (Group 2) - are the subjects of this report. The Group 1 waste was anticipated to be high in phosphorus and was implicitly assumed to be present as BiPO4 (however, results presented here indicate that the phosphate in Group 1 is actually present as amorphous iron(III) phosphate). The Group 2 waste was also anticipated to be high in phosphorus, but because of the relatively low bismuth content and higher aluminum content, it was anticipated that the Group 2 waste would contain a mixture of gibbsite, sodium phosphate, and aluminum phosphate. Thus, the focus of the Group 1 testing was on determining the behavior of P removal during caustic leaching, and the focus of the Group 2 testing was on the removal of both P and Al. The waste-type definition, archived sample conditions, homogenization activities, characterization (physical, chemical, radioisotope, and crystal habit), and caustic leaching behavior as functions of time, temperature, and hydroxide concentration are discussed in this report. Testing was conducted according to TP-RPP-WTP-467

Investigation of alternative phosphating treatments for nickel and hexavalent chromium elimination

International Nuclear Information System (INIS)

Jazbinsek, Luiz Antonio Rossi

2014-01-01

The phosphating processes are widely used in industry as surface treatments for metals, especially for low thickness plates, improving the adhesion between the metallic surface and the paint coating, and increasing the durability of paint systems against corrosion attacks. The tricationic phosphates containing zinc, nickel and manganese are commonly applied on steel. There is much discussion about the replacement of nickel by another element in order to have an environmentally friendly phosphating process. Niobium as a replacement for nickel has been evaluated. The most significant environmental impacts of phosphating processes are related to the presence of nickel and hexavalent chromium used in the process, this last as a passivation treatment. Nickel and hexavalent chromium are harmful to human and environment leading to contamination of water and soil. In the present study phosphate layers containing zinc, manganese and niobium have been evaluated and characterized on galvanized steel, and the results were compared with phosphates containing zinc, manganese and nickel, or a bicationic phosphate layer with zinc and manganese. Although the use of hexavalent chromium is not recommended worldwide, it is still used in processes for sealing the porosity of phosphate layers. This element is carcinogenic and has been associated with various diseases. Due to the passivation characteristics of niobium, this study also evaluated the tricationic bath containing niobium ammonium oxalate as a passivation treatment. The results showed that it could act as a replacement for the hexavalent chromium. The results of the present study showed that formulations containing niobium are potential replacements for hexavalent chromium and similar corrosion protection was obtained for the phosphate containing nickel or that with niobium. The morphology observed by scanning electron microscopy, gravimetric tests, porosity and adhesion evaluation results indicated that the phosphate

Role of magnesium on the biomimetic deposition of calcium phosphate

Science.gov (United States)

Sarma, Bimal K.; Sarma, Bikash

2016-10-01

Biomimetic depositions of calcium phosphate (CaP) are carried out using simulated body fluid (SBF), calcifying solution and newly developed magnesium containing calcifying solution. Calcium phosphate has a rich phase diagram and is well known for its excellent biocompatibility and bioactivity. The most common phase is hydroxyapatite (HAp), an integral component of human bone and tooth, widely used in orthopedic and dental applications. In addition, calcium phosphate nanoparticles show promise for the targeted drug delivery. The doping of calcium phosphate by magnesium, zinc, strontium etc. can change the protein uptake by CaP nanocrystals. This work describes the role of magnesium on the nucleation and growth of CaP on Ti and its oxide substrates. X-ray diffraction studies confirm formation of HAp nanocrystals which closely resemble the structure of bone apatite when grown using SBF and calcifying solution. It has been observed that magnesium plays crucial role in the nucleation and growth of calcium phosphate. A low magnesium level enhances the crystallinity of HAp while higher magnesium content leads to the formation of amorphous calcium phosphate (ACP) phase. Interestingly, the deposition of ACP phase is rapid when magnesium ion concentration in the solution is 40% of calcium plus magnesium ions concentration. Moreover, high magnesium content alters the morphology of CaP films.

Uranium, thorium and potassium contents and radioactive equilibrium states of the uranium and thorium series nuclides in phosphate rocks and phosphate fertilizers

Energy Technology Data Exchange (ETDEWEB)

Komura, K; Yanagisawa, M; Sakurai, J; Sakanoue, M

1985-10-01

Uranium, thorium and potassium contents and radioactive equilibrium states of the uranium and thorium series nuclides have been studied for 2 phosphate rocks and 7 phosphate fertilizers. Uranium contents were found to be rather high (39-117 ppm) except for phosphate rock from Kola. The uranium series nuclides were found to be in various equilibration states, which can be grouped into following three categories. Almost in the equilibrium state, 238U approximately 230Th greater than 210Pb greater than 226Ra and 238U greater than 230Th greater than 210Pb greater than 226Ra. Thorium contents were found to be, in general, low and appreciable disequilibrium of the thorium series nuclides was not observed except one sample. Potassium contents were also very low (less than 0.3% K2O) except for complex fertilizers. Based on the present data, discussions were made for the radiation exposure due to phosphate fertilizers.

Study on the adsorption and desorption of fertilizer phosphates by the soil suspensions

International Nuclear Information System (INIS)

Puspodikoro, S.

1978-01-01

The adsorption and desorption of fertilizer phosphate by soil suspensions were studied with the purpose to improve the efficiency of the use of phosphate fertilizer in rice growing countries. Experiments have shown that the applied phosphate fertilizer was quickly adsorbed by the soil and that the bulk of the fertilizer phosphate got bound to the soil complex. These bound fertilizer phosphates could readily be desorbed by flooding of the soil up to a certain amount. (author)