WorldWideScience

Sample records for plastic paint bucket

  1. Adaptive plasticity model for bucket foundations

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Barari, Amin; Larsen, Kim A.

    2014-01-01

    Based on experimental investigations, the literature proposes different methods for modeling the behavior and capacity of foundations subjected to combined loading. Generally, two methods are used to predict the behavior of foundations: traditional approaches and hardening plasticity solutions....... The first method is only capable of determining the capacity of the foundations and not the prepeak behavior. Thus, a new strain-hardening criterion is developed by calibrating failure criteria by employing data from small-scale tests on bucket foundations subjected to static loads. The shape of the yield...

  2. Effect of embedment on the plastic behaviour of Bucket Foundations

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Barari, Amin; Larsen, Kim André

    2015-01-01

    studies have indicated the possibility of defining foundation response using plasticity theory. Results of multiple loading tests addressing the effect of embedment on the strain-hardening behavior of shallow bucket foundations under combined loading are reported. The kinematic mechanisms accompanying pre...

  3. Suction Buckets

    DEFF Research Database (Denmark)

    Feld, T.

    on the performed numerical simulations, the analytical models and concepts like penetration resistance and critical suction. The employment of finite element calculations in the design of bucket foundation is evaluated and found necessary in the detailed design. However, introductory the determination......This Ph.D. thesis deals with bucket foundations and their applicability for offshore wind turbines. The main concern is the establishment of an analytical model for frictional materials, combined with simulations of buckets with varying geometry. An analytical model is proposed, consisting...... of different parts describing the penetration resistance during installation, the phenomenon critical suction and calculation methods for determination of the pullout force, respectively the response under combined loading, equivalent to ship impact, wave actions etc. A series of experimental tests conducted...

  4. Painting

    DEFF Research Database (Denmark)

    Petersen, Anne Ring

    2012-01-01

    energy has been put into expanding painting physically by exploring painting’s relations to objects, space, place, and ‘the everyday’. The text focuses on works of art that are conceived as an installation based on the medium of painting, including works by Slovak artists Dorota Sadovská and Daniel...... a commonly held opinion that painting has transformed itself into an expanded field and thus renewed itself – again. The article argues that in recent decades a remarkable number of painters have explored the possibility of developing painting by redefining what ‘space’ is in relation to painting. Much....... Text in English (pp. 66-83) and Slovak (pp. 44-65)....

  5. Bucket foundations

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo

    In this report, bearing behaviour and installation of bucket foundations are reviewed. Different methods and standards are compared with the experimental data presented in Foglia and Ibsen (2014a). The most important studies on these topics are suggested. The review is focused on the response...

  6. Suction Buckets

    DEFF Research Database (Denmark)

    Feld, T.

    of different parts describing the penetration resistance during installation, the phenomenon critical suction and calculation methods for determination of the pullout force, respectively the response under combined loading, equivalent to ship impact, wave actions etc. A series of experimental tests conducted...... on the performed numerical simulations, the analytical models and concepts like penetration resistance and critical suction. The employment of finite element calculations in the design of bucket foundation is evaluated and found necessary in the detailed design. However, introductory the determination...

  7. Process industries - graphic arts, paint, plastics, and textiles: all cousins under the skin

    Science.gov (United States)

    Simon, Frederick T.

    2002-06-01

    The origin and selection of colors in the process industries is different depending upon how the creative process is applied and what are the capabilities of the manufacturing process. The fashion industry (clothing) with its supplier of textiles is the leader of color innovation. Color may be introduced into textile products at several stages in the manufacturing process from fiber through yarn and finally into fabric. The paint industry is divided into two major applications: automotive and trades sales. Automotive colors are selected by stylists who are in the employ of the automobile manufacturers. Trade sales paint on the other hand can be decided by paint manufactureres or by invididuals who patronize custom mixing facilities. Plastics colors are for the most part decided by the industrial designers who include color as part of the design. Graphic Arts (painting) is a burgeoning industry that uses color in image reproduction and package design. Except for text, printed material in color today has become the norm rather than an exception.

  8. Bucket drill

    Energy Technology Data Exchange (ETDEWEB)

    Bezverkhiy, V.M.; Nabokov, I.M.; Podoksik, D.Z.; Sadovskiy, S.S.; Shanyukevich, V.A.

    1983-01-01

    The bucket drill including a cylindrical housing with bottom, ground intake windows and cutting knives is hinged to the housing, the mechanism of rotation of the cutting knives including rods connected by the cutter knives, and drive shaft is distinguished by the fact that in order to improve the effectiveness of drilling by automatic change in the angle of cutting depending on the strength of the drillable rock, the drill is equipped with elastic elements and cap with annular slits in which there are elastic elements. The mechanism of rotation of the cutting knives is equipped with levers hinged to the housing, pins with shaft and rocker arm. The rods are made with a slit and from one end are rigidly connected to the cutting knives, and from the other end to the levers by means of pins which are arranged in slits of the rod with the possibility of movement. The upper ends of the levers are installed with the possibility of movement in the pins whose shafts are arranged with the possibility of rotation in the rocker arm rigidly connected to the drive shaft. The drive shaft is equipped with cantilevers installed in the cap with the possibility of rotation and interaction with the elastic elements.

  9. The Monopod Bucket Foundation

    DEFF Research Database (Denmark)

    Bakmar, Christian LeBlanc; Ahle, Kim; Nielsen, Søren A.;

    2009-01-01

    Following the successful installation of a prototype of a monopod bucket foundation, also called a “monopod suction caisson”, at Horns Rev 2 Offshore Wind Farm, Denmark, in 2009, DONG Energy is currently developing a commercialization strategy. The monopod bucket foundation is a promising...... foundation concept for offshore wind turbines and can be installed using suction assisted penetration, combined with other installation methods. This selfinstalling foundation concept, may avoid the use of expensive jack-ups and scour protection, and thus significantly reduces installation costs. However......, further research, development and prototype testing are required, before the monopod bucket foundation can be commercialized....

  10. The Monopod Bucket Foundation

    DEFF Research Database (Denmark)

    Bakmar, Christian LeBlanc; Ahle, Kim; Nielsen, Søren A.

    2009-01-01

    Following the successful installation of a prototype of a monopod bucket foundation, also called a “monopod suction caisson”, at Horns Rev 2 Offshore Wind Farm, Denmark, in 2009, DONG Energy is currently developing a commercialization strategy. The monopod bucket foundation is a promising...... foundation concept for offshore wind turbines and can be installed using suction assisted penetration, combined with other installation methods. This selfinstalling foundation concept, may avoid the use of expensive jack-ups and scour protection, and thus significantly reduces installation costs. However...

  11. Buckling of Bucket Foundations

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    2012-01-01

    In this paper, the risk of structural buckling during installation of large-diameter bucket foundations is addressed using numerical methods. Imperfect geometries are introduced based on the pre-buckling mode shapes from a linear Eigenvalue buckling analysis. Various imperfect geometries are intr...

  12. Buckling of Bucket Foundations

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    2012-01-01

    In this paper, the risk of structural buckling during installation of large-diameter bucket foundations is addressed using numerical methods. Imperfect geometries are introduced based on the pre-buckling mode shapes from a linear Eigenvalue buckling analysis. Various imperfect geometries...... are introduced to reveal how sensitive the buckling load is to the mentioned imperfections. Including the first 21 mode shapes as imperfect geometries reduces the buckling pressure compared to only considering mode 1....

  13. Determination of dibutyl phthalate in plastic bucket containing bulk liquor%盛装散装白酒的塑料桶中邻苯二甲酸二丁酯的测定

    Institute of Scientific and Technical Information of China (English)

    陈雅; 李明元

    2012-01-01

    According to the survey that rural market to hold bulk liquor extensively use of plastic bucket. Hexane was used to extraction solvent,extract dibutyl phthalate(DBP) from the plastic buckets containing bulk liquor by ultrasound-assisted extraction as well as dibutyl phthalate quantification was performed by high performance liquid chromatography(HPLC). Extraction time,material/liquid ratio and extraction temperature were investigated with single-factor test. Response surface methodology based on Box-Behnken experimental desigen was used for process optimization. The optimal extraction conditions determined were extraction time of 52min, material/liquid ratio of 1:40,extraction temperature of 49℃. Under these conditions,the extraction volume of DBP was up to 32.21mg/kg,which was consistent with the prediction value. In the scope of 0.5~50.0mg/L, dibutyl phthalate had good linear relationship(R2=0.9998),lowest detectable limit was 0.017mg/L. The relative standard deviation of standard experimental precision was 0.40%,the recovery of dibutyl phthalate was 99.68% and the relative standard deviation was 0.85% ,the result showed that this extract method was accurate and reliable. This provided the basic data for food safety and the risk assessment of plasticizer.%摘要:据调查,农村市场广泛使用塑料桶盛装散装白酒。以正己烷作为提取溶剂.采用超声波辅助提取盛装散装白酒的塑料桶中邻苯二甲酸二丁酯(DBP),高效液相(HPLC)测定其含量。以提取时间、料液比、提取温度进行单因素实验,采用响应曲面Box—Behnken设计分析方法对其最佳提取条件进行优化。结果表明.邻苯二甲酸二丁酯最佳的提取条件为:提取时间为52min、料液比为1:40、提取温度为49℃,在此条件下,DBP提取量为32.21mg/kg.与理论预测值基本吻合。在0.5~50.0mg/L范围内邻苯二甲酸二丁酯具有良好的线性关系(R2=0.9998

  14. Recycler barrier RF buckets

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, C.M.; /Fermilab

    2011-03-01

    The Recycler Ring at Fermilab uses a barrier rf systems for all of its rf manipulations. In this paper, I will give an overview of historical perspective on barrier rf system, the longitudinal beam dynamics issues, aspects of rf linearization to produce long flat bunches and methods used for emittance measurements of the beam in the RR barrier rf buckets. Current rf manipulation schemes used for antiproton beam stacking and longitudinal momentum mining of the RR beam for the Tevatron collider operation are explained along with their importance in spectacular success of the Tevatron luminosity performance.

  15. Inferring compositional style in the neo-plastic paintings of Piet Mondrian by machine learning

    Science.gov (United States)

    Andrzejewski, David; Stork, David G.; Zhu, Xiaojin; Spronk, Ron

    2010-02-01

    We trained generative models and decision tree classifiers with positive and negative examples of the neo-plastic works of Piet Mondrian to infer his compositional principles, to generate "faux" works, and to explore the possibility of computer-based aids in authentication and attribution studies. Unlike previous computer work on this and other artists, we used "earlier state" works-intermediate versions of works created by Mondrian revealed through x-radiography and infra-red reflectography-when training our classifiers. Such intermediate state works provide a great deal of information to a classifier as they differ only slightly from the final works. We used methods from machine learning such as leave-one-out cross validation. Our decision tree classifier had accuracy of roughly 70% in recognizing the genuine works of Mondrian versus computer-generated replicas with similar statistical properties. Our trained classifier reveals implicit compositional principles underlying Mondrian's works, for instance the relative visual "weights" of the four colors (red, yellow, blue and black) he used in his rectangles. We used our trained generative model to generate "faux" Mondrians, which informally possess some of the compositional attributes of genuine works by this artist.

  16. Static Behaviour of Bucket Foundations

    DEFF Research Database (Denmark)

    Larsen, Kim André

    . The monopod concept is investigated in this thesis, regarding the static behaviour from loads relevant to offshore wind turbines. The main issue in this concept is the rotational stiffness of the foundation and the combined capacity dominated by moments. The vertical bearing capacity of bucket foundations...... theory is proposed. The proposed expression applies to plane strain as well as axis-symmetric stress conditions for foundations with smooth or rough bases. A thorough experimental investigation of the static behaviour of bucket foundations subjected to combined loading is carried out. Laboratory tests...... as well as large-scale tests on bucket foundations subjected to low vertical load are performed during this work. Numerical simulations of the tests performed are carried out using the Mohr Coulomb material model and the commercial finite element code ABAQUS. Based on the present work, the finite element...

  17. Scour Development around Bucket Foundations

    DEFF Research Database (Denmark)

    Stroescu, Ionut Emanuel; Frigaard, Peter Bak; Fejerskov, Morten

    2015-01-01

    The design without scour protection is a sensitive topic to most offshore developers, especially in the North Sea. However, newer research show that this concept is realistic if exists extended comprehension of the scour and backfill phenomena. The present paper shows comparative results for mono......The design without scour protection is a sensitive topic to most offshore developers, especially in the North Sea. However, newer research show that this concept is realistic if exists extended comprehension of the scour and backfill phenomena. The present paper shows comparative results...... for monopile and Bucket Foundation; using experimental analysis and real scour surveys around offshore installed Bucket Foundations. The main finding reflect that Bucket Foundation is a candidate for design without scour protection behaving like scour protected monopoles, in a variety of environmental...

  18. Static Behaviour of Bucket Foundations

    DEFF Research Database (Denmark)

    Larsen, Kim André

    . The monopod concept is investigated in this thesis, regarding the static behaviour from loads relevant to offshore wind turbines. The main issue in this concept is the rotational stiffness of the foundation and the combined capacity dominated by moments. The vertical bearing capacity of bucket foundations...... theory is proposed. The proposed expression applies to plane strain as well as axis-symmetric stress conditions for foundations with smooth or rough bases. A thorough experimental investigation of the static behaviour of bucket foundations subjected to combined loading is carried out. Laboratory tests...... method is concluded to be a superior method in estimating the post peak behaviour as well as the combined capacity of bucket foundations in relation to the offshore wind turbine problem....

  19. BONE CHAR BASED BUCKET DEFLUORIDATOR IN TANZANIAN HOUSEHOLDS

    DEFF Research Database (Denmark)

    Jacobsen, P.; Dahi, Elian

    1997-01-01

    A household defluoridator, made of a 20 L plastic bucket and 10 kg of bone char, is tested and found efficient to remove fluoride at a capacity of 1.1 mg/g. On an average, the defluoridator reduced the original contents of 8.5 mgF/L to 0.37 mgF/L, i.e. 95.6 %, for a period of 2 months, where 32.5...

  20. Characteristic Behavior of Bucket Foundations

    DEFF Research Database (Denmark)

    Barari, Amin

    the design of offshore wind turbine foundations. The work was divided into two main research efforts: geotechnical engineering experiments to gain insight into the behavior of offshore bucket foundations, and development of methods to improve the study of infiltration into unsaturated soils, an important...

  1. Characteristic Behavior of Bucket Foundations

    DEFF Research Database (Denmark)

    Barari, Amin

    reduce the risks and costsrelated to offshore geotechnics. The thesis examines: 1.Characteristic Behavior of Bucket Foundations 2. Modeling of Water Flow through Porous Media The outcomes of each of the research contributions are summarized in four research articles, either directly or indirectly...

  2. Characteristic Behavior of Bucket Foundations

    DEFF Research Database (Denmark)

    Barari, Amin

    reduce the risks and costsrelated to offshore geotechnics. The thesis examines: 1.Characteristic Behavior of Bucket Foundations 2. Modeling of Water Flow through Porous Media The outcomes of each of the research contributions are summarized in four research articles, either directly or indirectly...

  3. Buckets of Higgs and Tops

    CERN Document Server

    Buckley, Matthew R; Schell, Torben; Takeuchi, Michihisa

    2013-01-01

    We show that associated production of a Higgs with a top pair can be observed in purely hadronic decays. Reconstructing the top quarks in the form of jet buckets allows us to control QCD backgrounds as well as signal combinatorics. The background can be measured from side bands in the reconstructed Higgs mass. We back up our claims with a detailed study of the QCD event simulation, both for the signal and for the backgrounds.

  4. Buckets of Higgs and tops

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, Matthew R. [Center for Particle Astrophysics, Fermi National Accelerator Laboratory,Batavia, IL (United States); Department of Physics and Astronomy, Rutgers University,Piscataway, NJ (United States); Plehn, Tilman; Schell, Torben [Institut für Theoretische Physik, Universität Heidelberg,Heidelberg (Germany); Takeuchi, Michihisa [Theoretical Particle Physics and Cosmology Group, Department of Physics,King’s College London, London WC2R 2LS (United Kingdom)

    2014-02-28

    We show that associated production of a Higgs with a top pair can be observed in purely hadronic decays. Reconstructing the top quarks in the form of jet buckets allows us to control QCD backgrounds as well as signal combinatorics. The background can be measured from side bands in the reconstructed Higgs mass. We back up our claims with a detailed study of the QCD event simulation, both for the signal and for the backgrounds.

  5. Instability of Bucket Foundations during Installation

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    The bucket foundation is an upcoming technology for offshore wind turbines. The bucket foundation is a large cylindrical monopod foundation constructed as a thin steel shell structure. A bucket foundation does not require heavy installation equipment since it is installed by suction forces....... The combination of a thin shell structure and suction forces leads to the fact that instability, in form of buckling, becomes a crucial issue during installation. The hydrostatic buckling pressure of the bucket foundation is addressed using three-dimensional, non-linear finite element analysis. The results...

  6. Scour and Scour Protection for Bucket Foundations

    DEFF Research Database (Denmark)

    Larsen, Brian Juul; Frigaard, Peter

    A test programme has been performed to determine the scour around a bucket foundation for an offshore windturbine. furthermore the necessary scour protection has been investigated.......A test programme has been performed to determine the scour around a bucket foundation for an offshore windturbine. furthermore the necessary scour protection has been investigated....

  7. Bucket foundations:a literature review

    OpenAIRE

    Foglia, Aligi; Ibsen, Lars Bo

    2014-01-01

    In this report, bearing behaviour and installation of bucket foundations are reviewed. Different methods and standards are compared with the experimental data presented in Foglia and Ibsen (2014a). The most important studies on these topics are suggested. The review is focused on the response of monopod bucket foundations supporting offshore wind turbines.

  8. Bucket foundations under lateral cyclic loading

    DEFF Research Database (Denmark)

    Foglia, Aligi

    -competitive in the energy market. This thesis addresses issues concerning monopod bucket foundations in the hope of providing tools and ideas that could be used to optimize the design of this sub-structure. The work is focussed on the behaviour of bucket foundations under lateral cyclic loading. Other related......To enable a prosperous development of offshore wind energy, economically feasible technologies must be developed. The monopod bucket foundation is likely to become a cost-effective sub-structure for offshore wind turbines and has the potential to make offshore wind more cost...... and propaedeutic topics, such as bucket foundations under transient lateral loading and under monotonic lateral loading, are also investigated. All the scientific work is fundamentally based on small-scale experimental tests of bucket foundations in dense water-saturated sand. The most important scientific...

  9. Bucket Foundation Response Under Various Displacement Rates

    DEFF Research Database (Denmark)

    Vaitkunaite, Evelina; Nielsen, Benjaminn Nordahl; Ibsen, Lars Bo

    2016-01-01

    in a multi-bucket foundation system. The foundation model is at a scale of approximately 1:20 prototype foundation size. The tests are performed in a pressure tank with the foundation model installed in dense sand. Based on the data, the conclusion is that the bucket foundation design in a storm case should......The present testing program aims at showing the pore pressure response around a bucket foundation skirt as well as the load and displacement change due to ten different displacement rates. Research findings are useful for a numerical model calibration focusing on the design of the upwind foundation...

  10. Fixing the Hole in My Bucket

    Science.gov (United States)

    Nitkewicz, Edward J.

    2011-01-01

    Like many people, the author has spent the better part of his life fashioning a list of places he wanted to go and things he wanted to do. Because he is a typical American male, his "Bucket List" is mostly populated by sporting venues he wants to visit and sporting events he wants to witness. Sharing his "Bucket List" with his son would be a gift…

  11. Buckets: Smart Objects for Digital Libraries

    Science.gov (United States)

    Nelson, Michael L.

    2001-01-01

    Current discussion of digital libraries (DLs) is often dominated by the merits of the respective storage, search and retrieval functionality of archives, repositories, search engines, search interfaces and database systems. While these technologies are necessary for information management, the information content is more important than the systems used for its storage and retrieval. Digital information should have the same long-term survivability prospects as traditional hardcopy information and should be protected to the extent possible from evolving search engine technologies and vendor vagaries in database management systems. Information content and information retrieval systems should progress on independent paths and make limited assumptions about the status or capabilities of the other. Digital information can achieve independence from archives and DL systems through the use of buckets. Buckets are an aggregative, intelligent construct for publishing in DLs. Buckets allow the decoupling of information content from information storage and retrieval. Buckets exist within the Smart Objects and Dumb Archives model for DLs in that many of the functionalities and responsibilities traditionally associated with archives are pushed down (making the archives dumber) into the buckets (making them smarter). Some of the responsibilities imbued to buckets are the enforcement of their terms and conditions, and maintenance and display of their contents.

  12. Paint removal activities in Canada

    Science.gov (United States)

    Foster, Terry

    1993-03-01

    Paint removal activities currently under way in Canada include: research and development of laser paint stripping; development and commercialization of a new blasting medium based on wheat starch; commercialization of a new blasting medium and process using crystalline ice blasting for paint removal and surface cleaning; and the development of automated and robotic systems for paint stripping applications. A specification for plastic media blasting (PMB) of aircraft and aircraft components is currently being drafted by NDHQ for use by the Canadian Armed Forces (CAF) and contractors involved in coating removal for the CAF. Defense Research Establishment Pacific (DREP) is studying the effects of various blast media on coating removal rates, and minimizing the possibility of damage to substrates other than aluminum such as graphite epoxy composite and Kevlar. The effects of plastic media blasting on liquid penetrant detection of fatigue cracks is also under investigation.

  13. Painted Pickup.

    Science.gov (United States)

    Wheeler, Kimberly

    2001-01-01

    Discusses a six week art class project for elementary school children that lasted for six weeks. Explains that the students painted sunflowers in the style of Vincent van Gogh over the rust spots of a pickup truck. Reports that the painting served as great publicity for the art classes. (CMK)

  14. Monster Paintings

    Science.gov (United States)

    Huggler, Silvia

    2010-01-01

    In this article, the author describes a unit on monsters wherein students were charged with painting an imaginary character and, in so doing, demonstrated mastery of expression, organization of space, control of paint media, and application of the elements of art. Students discovered how color and line could be used to convey expression. The media…

  15. Painted Rhythms.

    Science.gov (United States)

    Bastian, Duane

    1985-01-01

    In this art activity gifted students, ages 10 to 13, learn about internal and external rhythms and make a painting of an internal rhythm. The lesson can be expanded with a discussion of Kandinsky, Pollock, and other painters who have painted sound or have demonstrated rhythms. (RM)

  16. Monster Paintings

    Science.gov (United States)

    Huggler, Silvia

    2010-01-01

    In this article, the author describes a unit on monsters wherein students were charged with painting an imaginary character and, in so doing, demonstrated mastery of expression, organization of space, control of paint media, and application of the elements of art. Students discovered how color and line could be used to convey expression. The media…

  17. Buckling of Bucket Foundations During Installation

    DEFF Research Database (Denmark)

    Madsen, Søren

    in order to reduce the cost of energy. This limits the on land application due to transportation limitations and unwillingness from prospect neighbours. Thus, offshore wind energy started developing over the last couple of years. Although installing the wind turbines offshore resolves the before men tioned...... issues, it brings up the cost of energy mainly due to increased installation and maintenance costs. A very large part—up to 30–50% using current technology—of the installation cost origins from the expenses related to the installation of foundations. A new foundation concept—the bucket foundation...... the suction assisted installation process. In this thesis, the phenomenon of buckling of the bucket foundation during installation is investigated by means of Finite Element Analysis. The influence of boundary conditions on the bucket foundation is adressed as well as the effect of including the surrounding...

  18. MPED: An ISRU Bucket Ladder Excavator Demonstrator System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Abstract: The Multi-Purpose Excavation Demonstrator (MPED) is a commercial effort and a third generation of technology, following Bucket Wheel Excavator and Bucket...

  19. Scour properties of mono bucket foundation

    DEFF Research Database (Denmark)

    Stroescu, Ionut Emanuel; Frigaard, Peter Bak

    2016-01-01

    Field experience proved that the Mono Bucket Foundations (MBFs) have good response against scour development. Moreover, the ratio between large diameter (bucket lid) and the small diameter (shaft tower) is the driving parameter for the process of erosion/backfill, like scour protection diameter...... in the case of scour protected monopiles. However, the structural design to reduce the scour development for MBFs is still open to optimization. The influences of parameters that generate backfill and scour, the transfer load webs and the misalignment with seabed, have not been systematically studied until...

  20. Monopod bucket foundations under cyclic lateral loading

    OpenAIRE

    Foglia, Aligi; Ibsen, Lars Bo

    2014-01-01

    The monopod bucket foundation can be a cost-reducing sub-structure for offshore wind turbines. To avoid problems during the turbine operation, the long-term effect of cyclic loading must be considered in the design of the foundation. In this paper a 1g testing rig is adopted to extend the knowledge on bucket foundations under lateral cyclic loading. The test setup is described in detail and a comprehensive experimental campaign is presented. The foundation is subjected to cyclic overturning m...

  1. Stiffness Formulation of Flexible Bucket Foundation

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Liingaard, Morten; Larsen, Kim André

    The response of offshore wind turbines e.g. static, eigen frequencies and eigen modes, are affected by elastic properties of the foundation and the subsoil. The Elastic Macro Model is developed to evaluate the soil-structure interaction of flexible bucket foundations for offshore wind turbines so...

  2. 30 CFR 57.10001 - Filling buckets.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Filling buckets. 57.10001 Section 57.10001 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Aerial Tramways § 57...

  3. 30 CFR 56.10001 - Filling buckets.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Filling buckets. 56.10001 Section 56.10001 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Aerial Tramways § 56.10001...

  4. Monopod bucket foundations under cyclic lateral loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo

    The monopod bucket foundation can be a cost-reducing sub-structure for offshore wind turbines. To avoid problems during the turbine operation, the long-term effect of cyclic loading must be considered in the design of the foundation. In this paper a 1g testing rig is adopted to extend the knowled...

  5. Monopod Bucket Foundations Under Cyclic Lateral Loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo

    2016-01-01

    The monopod bucket foundation has the potential to become a cost-reducing substructure for offshore wind turbines. To avoid problems during the energy converter operation, the long-term effect of cyclic loading must be considered in the design of the foundation. In this paper, a 1-g testing rig i...

  6. Stability of barrier buckets with zero RF-barrier separations

    Energy Technology Data Exchange (ETDEWEB)

    Ng, K.Y.; /Fermilab

    2005-03-01

    A barrier bucket with very small separation between the rf barriers (relative to the barrier widths) or even zero separation has its synchrotron tune decreasing rather slowly from a large value towards the boundary of the bucket. As a result, large area at the bucket edges can become unstable under the modulation of rf voltage and/or rf phase. In addition, chaotic regions may form near the bucket center and extend outward under increasing modulation. Application is made to those barrier buckets used in the process of momentum mining at the Fermilab Recycler Ring.

  7. Centrifugal experimental study of suction bucket foundations under dynamic loading

    Science.gov (United States)

    Lu, Xiaobing; Wu, Yongren; Jiao, Bintian; Wang, Shuyun

    2007-12-01

    Centrifugal experiments were carried out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, the sand at the upper part around the bucket is softened or even liquefied. The excess pore pressure decreases from the upper part to the lower part of the sand layer in the vertical direction and decreases radially from the bucket’s side wall in the horizontal direction. Large settlements of the bucket and the sand layer around the bucket are induced by dynamic loading. The dynamic responses of the bucket with smaller height (the same diameter) are heavier.

  8. Rock Paintings.

    Science.gov (United States)

    Jones, Julienne Edwards

    1998-01-01

    Discusses the integration of art and academics in a fifth-grade instructional unit on Native American culture. Describes how students studied Native American pictographs, designed their own pictographs, made their own tools, and created rock paintings of their pictographs using these tools. Provides a list of references on Native American…

  9. Dye Painting!

    Science.gov (United States)

    Johnston, Ann

    This resource provides practical instructions for applying color and design directly to fabric. Basic information about the dye painting process is given. The guide addresses the technical aspects of fabric dye and color use and offers suggestions for fabric manipulation and dye application in order to achieve various design effects. This…

  10. Dye Painting!

    Science.gov (United States)

    Johnston, Ann

    This resource provides practical instructions for applying color and design directly to fabric. Basic information about the dye painting process is given. The guide addresses the technical aspects of fabric dye and color use and offers suggestions for fabric manipulation and dye application in order to achieve various design effects. This…

  11. BEEM : Bucket Elimination with External Memory

    CERN Document Server

    Kask, Kalev; Gelfand, Andrew E

    2012-01-01

    A major limitation of exact inference algo- rithms for probabilistic graphical models is their extensive memory usage, which often puts real-world problems out of their reach. In this paper we show how we can extend in- ference algorithms, particularly Bucket Elim- ination, a special case of cluster (join) tree de- composition, to utilize disk memory. We pro- vide the underlying ideas and show promis- ing empirical results of exactly solving large problems not solvable before.

  12. Optimal Design of Stiffeners for Bucket Foundations

    OpenAIRE

    Courtney, William Tucker; Stolpe, Mathias; Buhl, Thomas; Bitsche, Robert; Hallum, Nicolai; Nielsen, Søren A.

    2015-01-01

    The potential for structural optimization of the bucket foundation’s outer stiffeners is investigated using commercial optimization software. In order to obtain the optimal design both shape and topology optimization problems are formulated and solved using the structural optimization software Tosca Structure coupled with the finite element software Abaqus. The solutions to these optimization problems are then manually interpreted as a new design concept. Results show that shape optimization ...

  13. Thermal Insulation System for Large Flame Buckets

    Science.gov (United States)

    Callens, E. Eugene, Jr.; Gamblin, Tonya Pleshette

    1996-01-01

    The objective of this study is to investigate the use of thermal protection coatings, single tiles, and layered insulation systems to protect the walls of the flame buckets used in the testing of the Space Shuttle Main Engine, while reducing the cost and maintenance of the system. The physical behavior is modeled by a plane wall boundary value problem with a convective frontface condition and a backface condition designed to provide higher heat rates through the material.

  14. Analysis of Bearing Capacity of Suction Bucket Foundation Subjected to Horizontal and Moment Loadings

    Directory of Open Access Journals (Sweden)

    W.U. Ke

    2013-07-01

    Full Text Available The suction bucket foundation is not only supporting the vertical loading such as the sea platform and weight itself, but also subjecting to horizontal and moment loading due to wind and wave. The response of bucket foundation to combined Horizontal (H and Moment (M loading has been studied using 3D finite element analysis Then the proposed method is numerically implemented in the framework of the general-purpose FEM software ABAQUS. Relationship curve between the coefficient of ultimate bearing capacity and displacement is obtained by the application of load-displacement controlled method in homogeneous soft foundation the failure envelope of foundation in the M-H is obtained by the application of swipe testing. The behavior is explained using upper bound plasticity mechanisms suggested by the soil deformation mechanisms observed in the finite element analysis. The numerical results computed by the proposed method will be helpful in engineering practices.

  15. Overview of paint removal methods

    Science.gov (United States)

    Foster, Terry

    1995-04-01

    With the introduction of strict environmental regulations governing the use and disposal of methylene chloride and phenols, major components of chemical paint strippers, there have been many new environmentally safe and effective methods of paint removal developed. The new methods developed for removing coatings from aircraft and aircraft components include: mechanical methods using abrasive media such as plastic, wheat starch, walnut shells, ice and dry ice, environmentally safe chemical strippers and paint softeners, and optical methods such as lasers and flash lamps. Each method has its advantages and disadvantages, and some have unique applications. For example, mechanical and abrasive methods can damage sensitive surfaces such as composite materials and strict control of blast parameters and conditions are required. Optical methods can be slow, leaving paint residues, and chemical methods may not remove all of the coating or require special coating formulations to be effective. As an introduction to environmentally safe and effective methods of paint removal, this paper is an overview of the various methods available. The purpose of this overview is to introduce the various paint removal methods available.

  16. Influential Factors of Bucket Foundation for Offshore Wind Turbine

    Institute of Scientific and Technical Information of China (English)

    丁红岩; 刘永刚; 张浦阳; 熊康平

    2015-01-01

    In this paper, the influential design factors of wide-shallow composite bucket foundation for 3 MW off-shore wind turbine are systematically studied by numerical simulation. The results show that the bucket diameter is larger than 27 m in general, and the range of 7—12 m is appropriate for cylinder height. In particular, the bucket foun-dation with diameter of 30 m and cylinder height of 10 m is suitable for most soils. Under ultimate loads, the bucket diameter and elasticity modulus of soil have major effects on the deformability of bucket foundation, while the influ-ence of friction coefficient between the bucket and soil is relatively slight.

  17. Centrifugal experimental study of suction bucket foundations under dynamic loading

    Institute of Scientific and Technical Information of China (English)

    Xiaobing Lu; Yongren Wu; Bintian Jiao; Shuyun Wang

    2007-01-01

    Centrifugal experiments were carded out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, the sand at the upper part around the bucket is softened or even liq-uefied. The excess pore pressure decreases from the upper part to the lower part of the sand layer in the vertical direc-tion and decreases radially from the bucket's side wall in the horizontal direction. Large settlements of the bucket and the sand layer around the bucket are induced by dynamic load-ing. The dynamic responses of the bucket with smaller height (the same diameter) are heavier.

  18. Thin-walled reinforcement lattice structure for hollow CMC buckets

    Energy Technology Data Exchange (ETDEWEB)

    de Diego, Peter

    2017-06-27

    A hollow ceramic matrix composite (CMC) turbine bucket with an internal reinforcement lattice structure has improved vibration properties and stiffness. The lattice structure is formed of thin-walled plies made of CMC. The wall structures are arranged and located according to high stress areas within the hollow bucket. After the melt infiltration process, the mandrels melt away, leaving the wall structure to become the internal lattice reinforcement structure of the bucket.

  19. Vertical Capacity of Bucket Foundations in Undrained Soil

    DEFF Research Database (Denmark)

    Barari, Amin; Ibsen, Lars Bo

    2014-01-01

    Offshore wind turbine structures are traditionally founded on gravity concrete foundations or mono-piles. Bucket foundations were developed for the offshore oil and gas industry and are now being used in wind turbine construction. The loading in this application is characterized by a vertical load...... due to the slender construction combined with horizontal forces inducing a large overturning moment. Field tests on bucket foundations were performed to gain insight into the vertical load response of bucket foundations in clay soils. The field tests were accompanied by finite element numerical...... simulations in order to provide a better understanding of the parameters influencing bucket foundation behavior....

  20. Design of Offshore Wind Power Foundation with Multi-bucket

    Institute of Scientific and Technical Information of China (English)

    张浦阳; 石建超; 丁红岩; 郭耀华

    2016-01-01

    Three- and four-bucket offshore wind power foundations with a new form of force-transferring structure are proposed in this paper, and the integrated finite element model of foundation-soil-transition structure is established by using ABAQUS. The carrying capacity of the proposed foundations is studied under vertical load, horizontal load and bending moment. It can be seen that the vertical bearing capacity of multi-bucket foundation can be roughly estimated by the vertical bearing capacity of single-bucket; the horizontal bearing capacity of the three-bucket foundation scheme is controlled by displacement, while that of the four-bucket foundation scheme is controlled by the internal forces of soils. Moreover, the carrying capacity is provided by the overall structure formed by multi-bucket before soil failure. Compared with the conventional single-bucket foundation, there are mainly tension and pressure that are applied to the multi-bucket foundation, so that the carrying capacity of the foundation can be fully utilized. The probability of soil failure can be well reduced with the proposed multi-bucket foundation, and the stress transmission of force-transferring structure is more consistent through steel beams with variable cross-section.

  1. Numerical Investigation Cavitation Buckets for Hydrofoil Parametrically

    Directory of Open Access Journals (Sweden)

    Mehmet Salih KARAALİOĞLU

    2015-12-01

    Full Text Available Cavitation is a general fluid mechanics phenomenon that is appeared in system such as pumps, turbines, marine propellers and hydrofoils which induces pressure and velocity fluctuation in the fluid (Brennen, 2013. Cavitation can be defined as the formation of vapour regions due to a decrease in local pressure. Undesirable consequences which can cause a fall in the performance of a system, structural failure, production of noise and vibration, material damage, are encountered due to cavitation (Uşar, 2015. In this study, cavitation was analysed using a bucket diagram. Bucket diagram represents the cavitation behaviour of a wing, fin or propeller blade in a two dimensional sense. This diagram is plotted as a function of section (hydrofoil angle of attack (α versus section cavitation number (σ. Pressure distribution can be calculated on two dimensional geometry of hydrofoil by using BEM (Boundary Element Method and cavitation bucket diagram can be computed. The cavitation inception case and partial cavitation cases have been investigated and the results of the present BEM were successfully compared with those of given in literature in the past and each other. While a constant source-dipole panel method has been used to calculate the pressure distribution at cavitation inception case, PCPAN programme that solves the sheet type of cavity on the hydrofoil by potential based panel method, has been used to calculate pressure distribution for the cases of partial cavitation. Effects of maximum hydrofoil thickness, maximum camber and location of maximum camber on cavitation have been analyzed by means of cavitation bucklet diagrams. All results are discussed in a detailed manner.

  2. Optimal Design of Stiffeners for Bucket Foundations

    DEFF Research Database (Denmark)

    Courtney, William Tucker; Stolpe, Mathias; Buhl, Thomas;

    2015-01-01

    The potential for structural optimization of the bucket foundation’s outer stiffeners is investigated using commercial optimization software. In order to obtain the optimal design both shape and topology optimization problems are formulated and solved using the structural optimization software...... Tosca Structure coupled with the finite element software Abaqus. The solutions to these optimization problems are then manually interpreted as a new design concept. Results show that shape optimization of the initial design can reduce stress concentrations by 38%. Additionally, topology optimization has...

  3. Bucket and straw technique to facilitate passage of a ventriculoperitoneal shunt through the distal tunneling sheath.

    Science.gov (United States)

    Downes, Angela E; Vandergrift, William A; Beckman, Joshua M; Truong, Devon; Tuite, Gerald F

    2014-12-01

    Placement of a ventriculoperitoneal shunt (VPS) is a procedure comprising many small steps. Difficulties and delays can arise when passing the distal shunt tubing down the distal tunneling sheath during surgery. The authors of this report describe a simple technique for quickly passing the distal catheter of a VPS through the tunneler sheath, whereby the sheath is used as a fluid tube to allow the distal catheter to be drawn through the fluid tube under suction pressure. The plastic sheath that surrounds the shunt tunneler device is used as a fluid tube, or "straw," with the proximal aperture submerged into a bucket of sterile irrigation liquid containing the distal catheter. Suction pressure is placed against the distal aperture of the tunneler, and the shunt catheter is quickly drawn through the sheath. No special equipment is required. In time trials, the bucket and straw technique took an average of 0.43 seconds, whereas traditional passage methods took 32.3 seconds. The "bucket and straw" method for passing distal shunt tubing through the tunneler sheath is a technique that increases surgical efficiency and reduces manual contact with shunt hardware.

  4. An Innovative Physical Model for Testing Bucket Foundations

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

    2012-01-01

    Monopod bucket foundations promise to become a reliable and cost-effective solution for offshore wind turbines. In this paper, six small scale tests of a steel bucket foundation subjected to quasi-static lateral load, are presented. When conducting small scale experiments on soil, scale effects c...

  5. Microwave instability in {alpha}-like quasi-isochronous buckets

    Energy Technology Data Exchange (ETDEWEB)

    Ng, K.Y.

    1996-10-01

    The problem of microwave instability inside an {alpha}-like quasi- isochronous bucket is addressed. The coupling impedance at wavelengths shorter than the length of the short bunches is found to be not small. The Keil-Schnell criterion is modified for such a bucket using the concept of self-bunching. The mechanism of particle loss during a microwave growth is examined.

  6. Drained Response of Bucket Foundations under Cyclic Lateral Load

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo

    2013-01-01

    Introduction The monopod bucket foundation is an innovative support structure for offshore wind turbines. It consists of a shallow embedded foundation which penetrates the seabed by means of a suction created within the caisson. The behaviour of bucket foundations against long-term lateral cyclic...

  7. Undrained Response of Bucket Foundations to Moment Loading

    DEFF Research Database (Denmark)

    Barari, Amin; Ibsen, Lars Bo

    2012-01-01

    Bucket foundation as a large cylindrical structure that is open at the base and closed at the top, is recently being used within the offshore wind turbines projects. The bearing capacity of bucket foundations to moment loading in undrained soil is of interest particularly to the offshore geotechn...

  8. Non-spill discharge characteristics of bucket elevators

    NARCIS (Netherlands)

    Rademacher, F.J.C.

    1979-01-01

    One of the well-known disadvantages of a simple type bucket elevator is still the backflow or spill. The accordingly lower capacity and increased power consumption are not always the worst consequences, provided that the boot does not become too full. With the considerable heights of modern bucket e

  9. Disdrometer and Tipping Bucket Rain Gauge Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Bartholomew. MJ

    2009-12-01

    The Distromet disdrometer model RD-80 and NovaLynx tipping bucket rain gauge model 260-2500E-12 are two devices deployed a few meters apart to measure the character and amount of liquid precipitation. The main purpose of the disdrometer is to measure drop size distribution, which it does over 20 size classes from 0.3 mm to 5.4 mm. The data from both instruments can be used to determine rain rate. The disdrometer results can also be used to infer several properties including drop number density, radar reflectivity, liquid water content, and energy flux. Two coefficients, N0 and Λ, from an exponential fit between drop diameter and drop number density, are routinely calculated. Data are collected once a minute. The instruments make completely different kinds of measurements. Rain that falls on the disdrometer sensor moves a plunger on a vertical axis. The disdrometer transforms the plunger motion into electrical impulses whose strength is proportional to drop diameter. The rain gauge is the conventional tipping bucket type. Each tip collects an amount equivalent to 0.01 in. of water, and each tip is counted by a data acquisition system anchored by a Campbell CR1000 data logger.

  10. Painting models

    Science.gov (United States)

    Baart, F.; Donchyts, G.; van Dam, A.; Plieger, M.

    2015-12-01

    The emergence of interactive art has blurred the line between electronic, computer graphics and art. Here we apply this art form to numerical models. Here we show how the transformation of a numerical model into an interactive painting can both provide insights and solve real world problems. The cases that are used as an example include forensic reconstructions, dredging optimization, barrier design. The system can be fed using any source of time varying vector fields, such as hydrodynamic models. The cases used here, the Indian Ocean (HYCOM), the Wadden Sea (Delft3D Curvilinear), San Francisco Bay (3Di subgrid and Delft3D Flexible Mesh), show that the method used is suitable for different time and spatial scales. High resolution numerical models become interactive paintings by exchanging their velocity fields with a high resolution (>=1M cells) image based flow visualization that runs in a html5 compatible web browser. The image based flow visualization combines three images into a new image: the current image, a drawing, and a uv + mask field. The advection scheme that computes the resultant image is executed in the graphics card using WebGL, allowing for 1M grid cells at 60Hz performance on mediocre graphic cards. The software is provided as open source software. By using different sources for a drawing one can gain insight into several aspects of the velocity fields. These aspects include not only the commonly represented magnitude and direction, but also divergence, topology and turbulence .

  11. Huashan rock paintings and other simitar paintings

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    China is one of the countries with the rechest rock paintings in the world. The Huashan rock paintings features color paintings, quite different from those in the North China areas where petroglyphs were created by engraving, chiseling,incising,or grinding,such as those in Inner Mongolia and Helan Mountains in Gansu.The rock paintings at Ulanchabu of Inner Mongolia are regarded as works of the Neolithic age,bronze age and iron age ,featuring mainly such grassland animals as

  12. Plastic progress study of eco-friendly paint%塑料用环保功能化涂料的研究进展

    Institute of Scientific and Technical Information of China (English)

    王云云; 杨建军; 张建安; 吴明元; 吴庆云

    2015-01-01

    Plastics,as one of the three main synthetic materials, have been widely used in the field of construction industry,household electrical appliances, automobile industry,etc., however, the deficiencies of themselves ask for to be decorated and improved with the functional coatings. The research process of the functional coatings for plastics, including water borne, UV curable, powder based, antimicrobial, fireproof and electro conductive coatings, were summerizedin this paper. And the future development trend of the coatings for plastics was outlooked.%塑料作为3大合成材料之一,在建筑、家电、汽车等领域被广泛使用,但自身的缺陷需要功能化涂料进行装饰和改善;综述了塑料用水性、UV固化、粉末、抗菌、防火、导电等环保功能化涂料的研究进展,并对塑料涂料未来的发展趋势进行展望。

  13. Negative Pressure Consolidation of Silt Inside Bucket Foundation

    Institute of Scientific and Technical Information of China (English)

    Ding Hongyan丁红岩; Liu Yonggang刘永刚; Zhang Puyang张浦阳

    2015-01-01

    A series of model experiments of bucket foundations concerning suction installation and negative pres-sure consolidation in saturated silt were carried out in a cube steel bin at Tianjin University. The experimental re-sults show that the silt inside the bucket has been strengthened by negative pressure, and the strengthening effect decreases with the increase of the distance from the bucket. A three-dimensional numerical model of the experi-ments was built by means of finite element software ABAQUS with fluid-solid coupling method. The results show that the bearing capacity of the silt inside the bucket foundation increases significantly at the former stage of nega-tive pressure consolidation, while the increasing trend slows down over time. The rotation centers of the bucket foundation and the inner soil region tend to be closer to each other based on the consolidation. The bearing capacity of the bucket foundation is improved effectively with the increase of soil strength. The effects of negative pressure consolidation on the bearing capacity of bucket foundation were also illustrated by an actual offshore wind power project case.

  14. Prototype bucket foundation for wind turbines

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Liingaard, Morten

    The first full scale prototype bucket foundation for wind turbines has been installed in October 2002 at Aalborg University offshore test facility in Frederikshavn, Denmark. The suction caisson and the wind turbine have been equipped with an online monitoring system, consisting of 15 accelerometers...... and a real-time data-acquisition system. The report concerns the in service performance of the wind turbine, with focus on estimation of the natural frequencies of the structure/foundation. The natural frequencies are initially estimated by means of experimental Output-only Modal analysis. The experimental...... estimates are then compared with numerical simulations of the suction caisson foundation and the wind turbine. The numerical model consists of a finite element section for the wind turbine tower and nacelle. The soil-structure interaction of the soil-foundation section is modelled by lumped-parameter models...

  15. Multispectral imaging using a single bucket detector

    CERN Document Server

    Bian, Liheng; Situ, Guohai; Li, Ziwei; Chen, Feng; Dai, Qionghai

    2015-01-01

    Current multispectral imagers suffer from low photon efficiency and limited spectrum range. These limitations are partially due to the technological limitations from array sensors (CCD or CMOS), and also caused by separative measurement of the entries/slices of a spatial-spectral data cube. Besides, they are mostly expensive and bulky. To address above issues, this paper proposes to image the 3D multispectral data with a single bucket detector in a multiplexing way. Under the single pixel imaging scheme, we project spatial-spectral modulated illumination onto the target scene to encode the scene's 3D information into a 1D measurement sequence. Conventional spatial modulation is used to resolve the scene's spatial information. To avoid increasing requisite acquisition time for 2D to 3D extension of the latent data, we conduct spectral modulation in a frequency-division multiplexing manner in the speed gap between slow spatial light modulation and fast detector response. Then the sequential reconstruction falls...

  16. Small-scale Testing of Bucket Foundations in Sand

    DEFF Research Database (Denmark)

    Knudsen, Bjørn S.; Østergaard, Martin Underlin; Ibsen, Lars Bo

    For offshore foundation structures, the loads are of varying nature both in magnitude and duration. For the bucket foundation the dissipation of the pore pressure is highly relevant since it greatly affects the strength of the structure. The build up of pore pressures with varying loading rate...... skirt will provide valuable information of the quasi-static behaviour. For a number of small-scale tests performed in the laboratory at Aalborg University, a bucket foundation will be loaded with varying velocity to investigate the dissipation and general behaviour of bucket foundations used as offshore...

  17. Example based painting generation

    Institute of Scientific and Technical Information of China (English)

    GUO Yan-wen; YU Jin-hui; XU Xiao-dong; WANG Jin; PENG Qun-sheng

    2006-01-01

    We present an approach for generating paintings on photographic images with the style encoded by the example paintings and adopt representative brushes extracted from the example paintings as the painting primitives. Our system first divides the given photographic image into several regions on which we synthesize a grounding layer with texture patches extracted from the example paintings. Then, we paint those regions using brushes stochastically chosen from the brush library, with further brush color and shape perturbations. The brush direction is determined by a direction field either constructed by a convenient user interactive manner or synthesized from the examples. Our approach offers flexible and intuitive user control over the painting process and style.

  18. Tangka Painting of Gesar

    Institute of Scientific and Technical Information of China (English)

    JAMBIAN; GYAMCO

    2002-01-01

    Rope and other patterns on pottery unearthed from the Karub cultural sites, dating back some 5,000 years, are considered to be the earliest examples of painting art known so far. Rock paintings believed to have come later constitute the embryo of Tibetan painting art.Tangka painting is closely related to frescoes in terms of painting art. Tangka is created to reproduce what is painted in the fresco. Cultures prevalent in China’s hinterland, India and Nepal exerted deep influence on Tibetan painting art.Both Princess Wencheng and Princess Jincheng brought the Han Chinese culture into Tibet, which proved to be a boon for the development of Tibetan painting art. With construction of the Potala Palace, Jokhang, Qamzhub and other monasteries, Tibetan painting art developed apace. Frescoes in Jokhang Monastery, Qamzhub Monastery and Potala Palace, still visible today, feature a simple nature, with rich colors and concise lines, while figures were painted in an

  19. Cooling circuit for a gas turbine bucket and tip shroud

    Energy Technology Data Exchange (ETDEWEB)

    Willett, Fred Thomas (25 Long Creek Dr., Burnt Hills, NY 12027); Itzel, Gary Michael (12 Cider Mill Dr., Clifton Park, NY 12065); Stathopoulos, Dimitrios (11 Wyngate Rd., Glenmont, NY 12077); Plemmons, Larry Wayne (late of Hamilton, OH); Plemmons, Helen M. (2900 Long Ridge Trails, Hamilton, OH 45014); Lewis, Doyle C. (444 River Way, Greer, SC 29651)

    2002-01-01

    An open cooling circuit for a gas turbine bucket wherein the bucket has an airfoil portion, and a tip shroud, the cooling circuit including a plurality of radial cooling holes extending through the airfoil portion and communicating with an enlarged internal area within the tip shroud before exiting the tip shroud such that a cooling medium used to cool the airfoil portion is subsequently used to cool the tip shroud.

  20. Bucket shaking stops bunch dancing in Tevatron

    Energy Technology Data Exchange (ETDEWEB)

    Burov, A.; Tan, C.Y.; /Fermilab

    2011-03-01

    Bunches in Tevatron are known to be longitudinally unstable: their collective oscillations, also called dancing bunches, persist without any signs of decay. Typically, a damper is used to stop these oscillations, but recently, it was theoretically predicted that the oscillations can be stabilized by means of small bucket shaking. Dedicated measurements in Tevatron have shown that this method does stop the dancing. According to predictions of Refs. [2,3], the flattening of the bunch distribution at low amplitudes should make the bunch more stable against LLD. An experiment has been devised to flatten the distribution by modulating the RF phase at the low-amplitude synchrotron frequency for a few degrees of amplitude. These beam studies show that stabilisation really happens. After several consecutive shakings, the dancing disappears and the resulting bunch profile becomes smoother at the top. Although not shown in this report, sometimes a little divot forms at the centre of the distribution. These experiments confirm that resonant RF shaking flattens the bunch distribution at low amplitudes, and the dancing stops.

  1. Multispectral imaging using a single bucket detector.

    Science.gov (United States)

    Bian, Liheng; Suo, Jinli; Situ, Guohai; Li, Ziwei; Fan, Jingtao; Chen, Feng; Dai, Qionghai

    2016-04-22

    Existing multispectral imagers mostly use available array sensors to separately measure 2D data slices in a 3D spatial-spectral data cube. Thus they suffer from low photon efficiency, limited spectrum range and high cost. To address these issues, we propose to conduct multispectral imaging using a single bucket detector, to take full advantage of its high sensitivity, wide spectrum range, low cost, small size and light weight. Technically, utilizing the detector's fast response, a scene's 3D spatial-spectral information is multiplexed into a dense 1D measurement sequence and then demultiplexed computationally under the single pixel imaging scheme. A proof-of-concept setup is built to capture multispectral data of 64 pixels × 64 pixels × 10 wavelength bands ranging from 450 nm to 650 nm, with the acquisition time being 1 minute. The imaging scheme holds great potentials for various low light and airborne applications, and can be easily manufactured as production-volume portable multispectral imagers.

  2. Egyptian Tomb Painting.

    Science.gov (United States)

    Schroeder, Liesa

    1999-01-01

    Provides an activity where sixth-grade students replicated the Egyptian art form of tomb painting. Explains that the students researched information about Egyptian culture and history in order to familiarize themselves with Egyptian wall-painting style. Discusses the process of creating tomb paintings in detail. (CMK)

  3. Paints and Preservatives.

    Science.gov (United States)

    Powell, Larry E.; Miller, Larry E.

    The publication contains an outline for use by agriculture teachers in developing a teaching plan for a unit on paints and preservatives. The topics included are (1) recognizing, solving, and preventing paint problems and (2) operating and using power spray painting equipment. Items presented for each topic are: the situation, (intended to inform…

  4. Recovery of spray paint traces from clothing by beating.

    Science.gov (United States)

    Olderiks, Maurice; Baiker, Martin; van Velzen, Jill; van der Weerd, Jaap

    2015-03-01

    Manual recovery of spray paints from textiles using a microscope, the routine method in many laboratories, is often laborious. Beating the clothing with a plastic rod, the routine method used for recovery of glass traces within the authors' laboratory, is proposed as an alternative. The efficiency of the method was evaluated by spray tests with fluorescent paint. In these tests, paint particles in the acquired debris samples, as well as those remaining on the textiles, were investigated. The results show that beating is an efficient way to recover and concentrate paint particles. A good efficiency for jeans fabric and rough knitwear is reported. The results appeared to be less satisfactory for smooth woven fabric. Application of the method in casework was effective for graffiti paints as well as for flaked car paint. © 2014 American Academy of Forensic Sciences.

  5. Synchronization of Synchrotrons for bunch-to-bucket Transfers

    CERN Document Server

    Ferrand, Thibault; Damerau, Heiko; CERN. Geneva. ATS Department

    2015-01-01

    To reach high particle energies with synchrotrons, a chain of several accelerators is required, as the ratio of extraction and injection energy is in the range of 10 to 20 per synchrotron. Hence the beam must be transfered from one accelerator to the next one. This document deals with the bunch-to-bucket transfer method to inject particle bunches composing the beam from a source synchrotron to a target synchrotron. After we highlight the theoretical concept of the bunch-to-bucket transfer, we determine physical limitations due to the beam dynamics and the adiabatic aspect of the particle bunches. A summary of the currently performed bunch-to-bucket transfer scenarios between the accelerators at CERN is given and set in relation with the mentioned theoretical concepts.

  6. A Preliminary Study on Bucket Foundations under Transient Lateral Loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Nielsen, Søren Kjær;

    2013-01-01

    This study aims at investigating the behaviour of monopod bucket foundations through a physical model. The foundation is installed in dense water-saturated sand and is subjected to lateral load applied at different rates. The different loading rates allow for exploring the patterns of response...... of bucket foundations in different drainage conditions. Particular focus is given to the rapid loading response of the foundation (simulating a 50 year wave or emergency stop of a wind turbine). Important knowledge on the pore pressure development within and around the foundation during loading is achieved....

  7. Comparison of design methods for axially loaded buckets in sand

    DEFF Research Database (Denmark)

    Vaitkunaite, Evelina; Nielsen, Benjaminn Nordahl; Ibsen, Lars Bo

    2015-01-01

    A study of the present knowledge about the bucket resistance for axial loading was performed considering analytical and numerical design methods as well as physical models. A case study was performed with two bucket foundations of equal diameter, but different skirt lengths installed in dense sand....... Itwas found that bearing capacity from the surcharge increases approximately twice if the foundation skirt is two times longer. However, the predicted compressive soil capacity can differ by 3.6 times depending on the chosen bearing capacity parameters. Few methods are available for the estimation...

  8. Newton’s Rotating Water Bucket: A Simple Model

    Science.gov (United States)

    2013-01-01

    twisted and the bucket is then released, it begins to spin and the surface of the water acquires a paraboloidal shape. In this paper, the parabolic...the bucket is then released, it begins to spin and the surface of the water acquires a paraboloidal shape. In this paper, the parabolic profile as a...second law [8], one finds that the water surface adopts the paraboloidal shape 2 2 0 2 rz z g ω= + (1) where 29.80 m/sg = is Earth’s gravitational

  9. Cost-Effective Mass Production of Mono Bucket Foundations

    DEFF Research Database (Denmark)

    Gres, Szymon; Nielsen, Søren Andreas; Fejerskov, Morten

    2015-01-01

    No recognized procedures exist for the Mono Bucket Foundation design, which is an obstruction for mass customization/production and industrialization in relation to certifying authorities. This paper presents the outcome of on-going research and development program that provides solution for inno......No recognized procedures exist for the Mono Bucket Foundation design, which is an obstruction for mass customization/production and industrialization in relation to certifying authorities. This paper presents the outcome of on-going research and development program that provides solution...

  10. Determination of p-y Curves for Bucket Foundations in Sand Using Finite Element Modeling

    OpenAIRE

    Knudsen, Bjørn S.; Østergaard, Martin Underlin; Ibsen, Lars Bo; Clausen, Johan

    2013-01-01

    Cylindrical offshore wind turbine foundations, such as bucket foundations and monopiles, have up till now been designed using analytical methods based on experiments done with piles much more slender than the ones used in today’s industry. Compared to the widely used monopile foundation, the suction bucket has a much smaller ratio between length and diameter, and the suction buckets will thus act more as a rigid object during rotation in the soil. To improve the design of suction buckets thro...

  11. Judgments of paintings

    Directory of Open Access Journals (Sweden)

    Marković Dragan

    2004-01-01

    Full Text Available In this study, the structure of the judgements of paintings was investigated. In the preliminary study, the subjects were asked to describe their subjective experience of paintings producing a list of attributes. The set of 76 most frequent attributes was selected and transformed into a bipolar 7-step scale (e.g. beautiful-ugly, strong-weak, interesting-boring etc. In the central part of the study, 200 subjects judged paintings on 76 scales. The paintings were grouped into two subgroups, A (200 paintings and B (200 paintings. This part of the study was conducted in two steps. In the first step, 200 subjects judged one of the 200 paintings from the subgroup A (each painting was judged only by one subject, whereas in the second step the same 200 subjects judged 200 paintings from the subgroup B (each painting was judged only by one subject.. Two simple data matrices, A and B, and one complex matrix A + B (string out matrix: matrix B is continued under the matrix A were obtained. The factor analyses (Promax and Orthoblique rotation have shown the consistency of a four factor extraction for three matrices (A, B i A+B using both rotation methods: Evaluation (clever, balanced, interesting, etc., Potency (rich, dense, relaxing etc., Cognitive factor (clear, ordinary, stimulative, etc. and Dynamics (provoking, tense, creative.

  12. Effect of Embedment on the Vertical Bearing Capacity of Bucket Foundations in Clay

    DEFF Research Database (Denmark)

    Barari, Amin; Ibsen, Lars Bo

    2011-01-01

    To evaluate the undrained behaviour of bucket foundations installed on Yoldia clay, 100 tests on bucket foundations subject to vertical and moment loadings were conducted at Aalborg university geotechnical centre. Bucket foundations are tubular steel foundations that are installed by sealing the ...

  13. On the robustness of bucket brigade quantum RAM

    Science.gov (United States)

    Arunachalam, Srinivasan; Gheorghiu, Vlad; Jochym-O'Connor, Tomas; Mosca, Michele; Varshinee Srinivasan, Priyaa

    2015-12-01

    We study the robustness of the bucket brigade quantum random access memory model introduced by Giovannetti et al (2008 Phys. Rev. Lett.100 160501). Due to a result of Regev and Schiff (ICALP ’08 733), we show that for a class of error models the error rate per gate in the bucket brigade quantum memory has to be of order o({2}-n/2) (where N={2}n is the size of the memory) whenever the memory is used as an oracle for the quantum searching problem. We conjecture that this is the case for any realistic error model that will be encountered in practice, and that for algorithms with super-polynomially many oracle queries the error rate must be super-polynomially small, which further motivates the need for quantum error correction. By contrast, for algorithms such as matrix inversion Harrow et al (2009 Phys. Rev. Lett.103 150502) or quantum machine learning Rebentrost et al (2014 Phys. Rev. Lett.113 130503) that only require a polynomial number of queries, the error rate only needs to be polynomially small and quantum error correction may not be required. We introduce a circuit model for the quantum bucket brigade architecture and argue that quantum error correction for the circuit causes the quantum bucket brigade architecture to lose its primary advantage of a small number of ‘active’ gates, since all components have to be actively error corrected.

  14. Testing of Axially Loaded Bucket Foundation with Applied Overburden Pressure

    DEFF Research Database (Denmark)

    Vaitkunaite, Evelina; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

    This report analyses laboratory testing data performed with a bucket foundation model subjected to axial loading. The examinations were conducted at the Geotechnical laboratory of Aalborg University. The report aims at showing and discussing the results of the static and cyclic axial loading tests...

  15. Laboratory experiments of bucket foundations under cyclic loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo

    This report collects information on the experimental campaign concerning bucket foundations under lateral cyclic loading conducted by the authors between 2011 and 2014. The report includes a step by step manual on the test procedures and a number of information and graphs for each experiment. In ...

  16. Lumped-parameter Model of a Bucket Foundation

    DEFF Research Database (Denmark)

    Andersen, Lars; Ibsen, Lars Bo; Liingaard, Morten

    2009-01-01

    As an alternative to gravity footings or pile foundations, offshore wind turbines at shallow water can be placed on a bucket foundation. The present analysis concerns the development of consistent lumped-parameter models for this type of foundation. The aim is to formulate a computationally effic...

  17. Time bucket length and lot-splitting approach

    NARCIS (Netherlands)

    Riezebos, J

    2004-01-01

    The effect of time bucket length on the choice of a lot-splitting approach is studied. Due to the continuing pressure to reduce throughput times and increase efficiency, managers apply various measures, such as lot splitting and cycle time reduction programmes, that change the length of the time buc

  18. Transient Monotonic and Cyclic Load Effects on Mono Bucket Foundations

    DEFF Research Database (Denmark)

    Nielsen, Søren Dam

    and when hitting the foundation they induce high impact loads with a short duration. It is important that the foundation is able to resists these huge loads. Fortunately, the conducted research showed that the capacity of the mono bucket foundation is high to impact loads. When exposed to a huge wave load...

  19. Laboratory experiments of bucket foundations under cyclic loading

    OpenAIRE

    Foglia, Aligi; Ibsen, Lars Bo

    2014-01-01

    This report collects information on the experimental campaign concerning bucket foundations under lateral cyclic loading conducted by the authors between 2011 and 2014. The report includes a step by step manual on the test procedures and a number of information and graphs for each experiment. In addition, all the tests performed with the relevant features are listed.

  20. A Preliminary Study on Bucket Foundations under Transient Lateral Loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Nielsen, Søren Kjær;

    2013-01-01

    This study aims at investigating the behaviour of monopod bucket foundations through a physical model. The foundation is installed in dense water-saturated sand and is subjected to lateral load applied at different rates. The different loading rates allow for exploring the patterns of response of...

  1. Investigation of seepage around the bucket skirt during installation in sand:AAU CPT-based method for the installation of suction bucket

    OpenAIRE

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo

    2015-01-01

    First aim of this study is to evaluate a pore pressure factor, . The factor describes the ratio between the excess pore pressure generated on the bucket tip and the applied suction under the bucket lid. The pore pressure factor can be then used for prediction of excess pore pressure at the tip or along bucket skirt with known soil condition, bucket geometry and applied suction.The second aim of the study is to evaluate expressions for normalized seepage length, s/h, for different soil combina...

  2. Oil-based paint poisoning

    Science.gov (United States)

    Paint - oil based - poisoning ... Hydrocarbons are the primary poisonous ingredient in oil paints. Some oil paints have heavy metals such as lead, mercury, cobalt, and barium added as pigment. These heavy metals can cause additional ...

  3. Jasper Johns' Painted Words.

    Science.gov (United States)

    Levinger, Esther

    1989-01-01

    States that the painted words in Jasper Johns' art act in two different capacities: concealed words partake in the artist's interrogation of visual perception; and visible painted words question classical representation. Argues that words are Johns' means of critiquing modernism. (RS)

  4. Chromosome painting in plants.

    NARCIS (Netherlands)

    Schubert, I.; Fransz, P.F.; Fuchs, J.; Jong, de J.H.

    2001-01-01

    The current 'state-of-art' as to chromosome painting in plants is reviewed. We define different situations described as painting so far: i) Genomic in situ hybridisation (GISH) with total genomic DNA to distinguish alien chromosomes on the basis of divergent dispersed repeats, ii) 'Chromosomal in si

  5. Chromosome painting in plants.

    NARCIS (Netherlands)

    Schubert, I.; Fransz, P.F.; Fuchs, J.; Jong, de J.H.

    2001-01-01

    The current 'state-of-art' as to chromosome painting in plants is reviewed. We define different situations described as painting so far: i) Genomic in situ hybridisation (GISH) with total genomic DNA to distinguish alien chromosomes on the basis of divergent dispersed repeats, ii) 'Chromosomal in

  6. Synergism in anticorrosive paints

    Indian Academy of Sciences (India)

    G BLUSTEIN; C DEYÁ; R ROMAGNOLI

    2016-06-01

    The present work depicts synergism anticorrosive behaviour between zinc hypophosphite and zinc phosphate in a commercial pigment mixture. Also, the performance of anticorrosive paints was evaluated. Synergism anticorrosive behaviour was evaluated by corrosion potential and linear polarization measurements in pigment suspensions. The protective layer obtained with this pigment mixture was investigated by scanning electron microscopy (SEM). Then, the anticorrosive properties of the pigment were assessed by incorporating it into alkyd and epoxy paints which were evaluated by salt spray test and electrochemical noise technique. The morphology and the nature of the protective layer grown under the paint film were also studied by SEM. Experimental results showed that improved anticorrosion protection is achieved in paints with reduced zinc phosphate contents as a consequence of the synergistic interaction between zinc hypophosphite and the other components of the pigment mixture. The electrochemical noise technique proved to be adequate to monitor corrosion in painted panels and is able to detectcorrosion under the paint film from very early stages. This paper identified the need to study synergism between anticorrosive pigments to try to reduce the phosphate content in anticorrosive paints.

  7. Prototype bucket foundation for wind turbines:natural frequency estimation

    OpenAIRE

    Ibsen, Lars Bo; Liingaard, Morten

    2006-01-01

    The first full scale prototype bucket foundation for wind turbines has been installed in October 2002 at Aalborg University offshore test facility in Frederikshavn, Denmark. The suction caisson and the wind turbine have been equipped with an online monitoring system, consisting of 15 accelerometers and a real-time data-acquisition system. The report concerns the in service performance of the wind turbine, with focus on estimation of the natural frequencies of the structure/foundation. The nat...

  8. Fire retardant paints

    Directory of Open Access Journals (Sweden)

    D.B. Parihar

    1954-04-01

    Full Text Available The mechanism involved in the flame-proofing of cellulose is explained on modern electronic concepts. Some recent developments on intumescent paint and mastic compositions with the scope of their further improvement are discussed.  

  9. Determination of p-y Curves for Bucket Foundations in Sand Using Finite Element Modeling

    DEFF Research Database (Denmark)

    Knudsen, Bjørn S.; Østergaard, Martin Underlin; Ibsen, Lars Bo

    , the suction bucket has a much smaller ratio between length and diameter, and the suction buckets will thus act more as a rigid object during rotation in the soil. To improve the design of suction buckets through analytical methods, the soil pressure needs to be calculated more precisely since currently...... available p􀀀y curves, linking displacement and soil pressure, are based on more slender cylindrical structures. Using finite element methods, the p􀀀y curves for suction buckets will be determined as a function of the internal angle of friction of the soil, the diameter and the skirt length...... of the suction buckets, which can in turn be applied in determination of soil pressures for analytical design methods of suction bucket foundations....

  10. Paint for Motherland

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ On August 15, the Chinese Outstanding Art Exhibition in calligraphy and painting will bc held in mid-ring of Hong Kong, where Olympic equestrian events co-hosted, representing the masterpieces of China mainland artists. The event is a part of exchange during the 2008 Olympic period among Olympic co-hosting cities. The most eyeball-attracting showpiece will be a 960 m2 painting. "Ten Thousand Miles of Motherland", from the hand of Zhao Xiufeng.

  11. Homesickness (Decorative Painting)

    Institute of Scientific and Technical Information of China (English)

    1995-01-01

    Traditionally. nchly colored Chinese painting is widely recognized for its line and rhythm. As early as 1.1000 years ago. the Dunhuang frescos of the Tang Dynasty (618907) reached a high level. "Homesickness" represents a female figure thinking about the motherland. The painter uses traditional painting techniques in reference to linn and color. The dragon and phoenix motif in the background represents the 5.000 year-old cultural history of

  12. Displaced Medial and Lateral Bucket Handle Meniscal Tears With Intact ACL and PCL.

    Science.gov (United States)

    Boody, Barrett S; Omar, Imran M; Hill, James A

    2015-08-01

    Bucket handle lesions are vertical longitudinal tears in the meniscus that may displace centrally into the respective medial or lateral compartment, frequently causing mechanical symptoms, including pain, perceived instability, and mechanical locking. Bucket handle meniscal tears are most commonly from a traumatic etiology and are frequently found with concomitant anterior cruciate ligament (ACL) injuries. Multiple imaging signs and associations have been described for the diagnosis of bucket handle meniscus tears, including coronal truncation, absent bow tie sign, double posterior cruciate ligament (PCL), double ACL, displacement of the bucket handle fragment, and disproportionate posterior horn signs. Among meniscal pathology encountered on magnetic resonance imaging or during arthroscopy, bucket handle meniscal tears are infrequent occurrences. Furthermore, the occurrence of displaced medial and lateral bucket handle tears found on imaging and during arthroscopy is very uncommon and is only sparsely reported in the literature. When displaced medial and lateral bucket handle meniscal segments are visualized within the intercondylar notch along with the ACL and PCL, the radiologic findings are referred to as the "quadruple cruciate" sign or the "Jack and Jill lesion." Of the few case reports described in the literature, only one noted displaced medial and lateral bucket handle meniscus tears with an intact ACL and PCL. The current case report outlines a similar rare case of the quadruple cruciate sign: displaced medial and lateral bucket handle meniscal tears located within the intercondylar notch and an intact ACL and PCL.

  13. The quadruple cruciate sign of simultaneous bicompartmental medial and lateral bucket-handle meniscal tears

    Energy Technology Data Exchange (ETDEWEB)

    Bugnone, Alejandro N. [University of Miami School of Medicine/Jackson Memorial Hospital, Department of Radiology, Miami, FL (United States); Ramnath, R.R. [Neuroskeletal Imaging, Merritt Island, FL (United States); Davis, S.B. [Orthopedic Center, Huntsville, Alabama (United States); Sedaros, R. [Space Coast Orthopedics, Merritt Island, FL (United States)

    2005-11-01

    We report the second known case of bicompartmental bucket-handle tears of the medial and lateral menisci and the first documented case of the bucket-handle tears occurring simultaneously following trauma, which occurred after a motorcycle accident. Both bucket-handle fragments were displaced into the intercondylar notch. An anterior cruciate ligament tear was also present. Coronal images demonstrated four structures in the intercondylar notch: the anterior and posterior cruciate ligaments and the medial and lateral bucket-handle meniscal fragments. (orig.)

  14. Experiments on Paint Rheology

    Science.gov (United States)

    Hartranft, Thomas J.; Settles, Gary S.

    1998-11-01

    We seek a better understanding of the atomization of paints for purposes of limiting the environmental impact of spray painting. However, to do so one must confront both the shear and extensional rheology of mobile non-Newtonian fluids whose very composition is often complex and even unknown. A conventional Couette rheometer yields data on paint shear behavior, but no commercial instrument is available to measure the extensional viscosity, which is believed to govern ligamentary breakup in spray painting. Here a converging-flow extensional rheometer has been built for this purpose. Flow rate and orifice pressure drop are measured and related to the rheological properties of the fluid. At first, experience was gained by visualizing in this device the flow of clear aqueous solutions of both Newtonian (glycerol) and non-Newtonian (polyacrylamide) thickeners. Commercial latex and marine paints were then tested, with the goal of characterizing their extensional behavior and the hope that they might be replaceable by simpler aqueous rheological "substitute" fluids insofar as their atomization behavior is concerned. (Research supported by the US Navy via the Penn State Applied Research Laboratory.)

  15. Integer Valued Autoregressive Models for Tipping Bucket Rainfall Measurements

    DEFF Research Database (Denmark)

    Thyregod, Peter; Carstensen, Niels Jacob; Madsen, Henrik

    1999-01-01

    A new method for modelling the dynamics of rain sampled by a tipping bucket rain gauge is proposed. The considered models belong to the class of integer valued autoregressive processes. The models take the autocorelation and discrete nature of the data into account. A first order, a second order...... and a threshold model are presented together with methods to estimate the parameters of each model. The models are demonstrated to provide a good description of dt from actual rain events requiring only two to four parameters....

  16. Hydrodynamics of the free surface flow in Pelton turbine buckets

    OpenAIRE

    Perrig, Alexandre; Avellan, François; Farhat, Mohamed

    2008-01-01

    The design of Pelton turbines has always been more difficult than that of reaction turbines, and their performances lower. Indeed, the Pelton turbines combine 4 types of flows: (i) confined, steady-state flow in the piping systems and injector, (ii) free water jets, (iii) 3D unsteady free surface flows in the buckets, and (iv) dispersed 2-phase flows in the casing. The flow in Pelton turbines has not been analyzed so far with such detail as the flow in the reaction turbines, thus the understa...

  17. Hydrodynamics of the free surface flow in Pelton turbine buckets

    OpenAIRE

    Perrig, Alexandre

    2007-01-01

    The design of Pelton turbines has always been more difficult than that of reaction turbines, and their performances lower. Indeed, the Pelton turbines combine 4 types of flows: (i) confined, steady-state flow in the piping systems and injector, (ii) free water jets, (iii) 3D unsteady free surface flows in the buckets, and (iv) dispersed 2-phase flows in the casing. The flow in Pelton turbines has not been analyzed so far with such detail as the flow in the reaction turbines, thus the understa...

  18. Modelling the embedded rainfall process using tipping bucket data

    DEFF Research Database (Denmark)

    Thyregod, Peter; Arnbjerg-Nielsen, Karsten; Madsen, Henrik;

    1998-01-01

    A new method for modelling the dynamics of rain measurement processes is suggested. The method takes the discrete nature and autocorrelation of measurements from the tipping bucket rain gauge into consideration. The considered model is a state space model with a Poisson marginal distribution....... In the model there is only one parameter, a thinning parameter. The model is tested on 39 rain events. The estimated value for the various rain events is reflecting a subjective classification of rain events into frontal and convective rain. Finally, it is demonstrated how the model can be used for simulation...

  19. Nanjing Painting & Calligraphy Academy

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    FOUNDED in 1979,the Nanj-ing Painting and CaligraphyAcademy consists of 20 profes-sional painters,over 40 invited paintersand a few brilliant graduates from sev-eral art schools.The academy hasemerged as a major art force,withmost of its members being young andmiddle-aged painters.The academy is composed of aChinese painting research studio,anexhibition section,arts and crafts salessection and an administrative office.In1992 the Nanjing municipal govern-ment made cotributions to the acade-my for the construction of a paintingstudio and an exhibition hall coveringa combined floor area of 1,000 square

  20. Introductory guide to painting

    CSIR Research Space (South Africa)

    Cromarty, R.E

    1985-01-01

    Full Text Available This is an interior decorative finish in which the pigment is bound with water- soluble glue or size. It is cheap and is sold in powder form for mixing with water. It cannot be used out of doors and will rub off if washed. Where a paint of a different kind has been... galvanised steel. The first is caused by the reactive nature of the zinc surface which damages alkyd paints and the second by the preservative that is often applied to the surface of sheet material during production. Once the steel has been exposed...

  1. Dragline bucket improvement survey. Final report, September 30, 1977-September 29, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Stilwell, T.; Kelly, H.; Rumbarger, J.; Dowling, M.

    1979-01-01

    An operating dragline bucket receives a lot of abuse. It logs about a million dig cycles every two or three years, all the while operating through abrasive overburden on a round-the-clock basis. It is to the credit of designers, operators and maintenance men alike that these buckets perform so well under such adverse conditions. Comments made in this report are for the purpose of focusing on areas in which further improvements can be made, and in no way are intended to reflect adversely on the generally high quality of bucket design, use and repair. From December 1977 to September 1978, investigators visited nine surface coal mines to review first-hand the techniques and problems associated with dragline equipment. The contractor also conducted some basic analyses regarding bucket geometry and force patterns. The report concludes that: dragline bucket and rigging designs, while traditionally satisfactory, could be bettered in some areas; the major maintenance problem associated with buckets and associated rigging is abrasive wear; the repair costs for associated rigging (primarily chains) can run in excess of 50% of the repair costs for buckets; there is no established engineering information available regarding stresses, forces, soil flow and soil resistance in relation to dragline buckets; present computer monitoring and analysis equipment could, with appropriate modifications, be utilized to yield useful engineering information.

  2. Buckling Analysis of Bucket Foundations for Wind Turbines in Deep Water

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars; Ibsen, Lars Bo

    2011-01-01

    Using large suction caissons for offshore wind turbines is an upcoming technology also referred to as bucket foundations. The bucket foundation does not require heavy installation equipment, but since it is constructed as a thin steel shell structure, instability, in form of buckling, becomes...

  3. Set-up and Test Procedure for Suction Installation and Uninstallation of Bucket Foundation

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna

    of suction under the bucket lid or by applying additional force through the hydraulic piston, forcing the bucket to penetrate into the soil. Tests for uninstallation are performed also with the use of water pressure, as a reverse process to the suction installation. Both installation and uninstallation tests...

  4. Small-Scale Testing of Laterally Loaded Bucket Foundations in Dense Sand

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Foglia, Aligi

    2011-01-01

    Monopod bucket foundations promise to become a reliable and cost-effective option for offshore wind turbine. In this paper, six small-scale tests of a steel bucket foundation subjected to quasi-static lateral load, are When conducting small-scale experiments on soil, scale effects can considerabl...

  5. Crafting the Set of Buckets in a R&D Portfolio

    DEFF Research Database (Denmark)

    Santiago, Leonardo; Soares, Verônica Mariana Oliveira

    2017-01-01

    The fact that R&D portfolio should be aligned with firm’s strategy is self-evident. The strategic buckets method is often posited in the literature as an alternative to ensure the strategic alignment. However, crafting the right set of buckets is not a straightforward task. In this paper, we cons...

  6. An Experimental Study of the Drained Capacity of Bucket Foundations for Offshore Applications

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Barari, Amin; Larsen, Kim André

    2013-01-01

    on offshore bucket foundations for wind turbines in saturated dense sand. The bearing capacity of bucket foundations subject to combined loadings which are of interest particularly to the offshore geotechnical engineers, were calculated and found to be largely dependent on embedment ratios and load paths...

  7. Unsteady CFD simulation for bucket design optimization of Pelton turbine runner

    Science.gov (United States)

    KUMASHIRO, Takashi; FUKUHARA, Haruki; TANI, Kiyohito

    2016-11-01

    To investigate flow patterns on the bucket of Pelton turbine runners is one of the important issues to improve the turbine performance. By studying the mechanism of loss generation on the flow around the bucket, it becomes possible to optimize the design of inner and outer bucket shape. For making it into study, computational fluid dynamics (CFD) is quite an effective method. It is normally used to simulate the flow in turbines and to expect the turbine performances in the development for many kind of water turbine including Pelton type. Especially in the bucket development, the numerical investigations are more useful than observations and measurements obtained in the model test to understand the transient flow patterns. In this paper, a numerical study on two different design buckets is introduced. The simplified analysis domain with consideration for reduction of computational load is also introduced. Furthermore the model tests of two buckets are also performed by using the same test equipment. As the results of the model test, a difference of turbine efficiency is clearly confirmed. The trend of calculated efficiencies on both buckets agrees with the experiment. To investigate the causes of that, the difference of unsteady flow patterns between two buckets is discussed based on the results of numerical analysis.

  8. Process Waste Assessment - Paint Shop

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, N.M.

    1993-06-01

    This Process Waste Assessment was conducted to evaluate hazardous wastes generated in the Paint Shop, Building 913, Room 130. Special attention is given to waste streams generated by the spray painting process because it requires a number of steps for preparing, priming, and painting an object. Also, the spray paint booth covers the largest area in R-130. The largest and most costly waste stream to dispose of is {open_quote}Paint Shop waste{close_quotes} -- a combination of paint cans, rags, sticks, filters, and paper containers. These items are compacted in 55-gallon drums and disposed of as solid hazardous waste. Recommendations are made for minimizing waste in the Paint Shop. Paint Shop personnel are very aware of the need to minimize hazardous wastes and are continuously looking for opportunities to do so.

  9. LSST Painting Risk Evaluation Memo

    Energy Technology Data Exchange (ETDEWEB)

    Wolfe, Justin E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-11-10

    The optics subsystem is required to paint the edges of optics black where possible. Due to the risks in applying the paint LSST requests a review of the impact of removing this requirement for the filters and L3.

  10. Oil Paintings by Ou Yang

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Ou Yang, professor of the Oil Painting Department of Guangdong Art College, has been pursuing perfection in the field of art for many years. With their rich emotional color, paintings by her do not simply

  11. A Painting Tells Its Story

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Separated parts of an ancient Chinese painting to be displayed together Chinese Premier Wen Jiabao told a story about a famous Chinese painting Dwelling in the Fuchun Mountains at a press conference after the Third Session of the

  12. Estimating the colors of paintings

    OpenAIRE

    Nascimento, Sérgio M C; Linhares, João M. M., ed. lit.; João, Catarina A. R.; Amano, Kinjiro; Montagner, Cristina; Melo, Maria J.; Vilarigues, Marcia

    2015-01-01

    Observers can adjust the spectrum of illumination on paintings for optimal viewing experience. But can they adjust the colors of paintings for the best visual impression? In an experiment carried out on a calibrated color moni- tor images of four abstract paintings obtained from hyperspectral data were shown to observers that were unfamiliar with the paintings. The color volume of the images could be manipulated by rotating the volume around the axis through the average (a*, b*) point for eac...

  13. Barrier Buckets and Transient Beam Loading in the SPS

    CERN Document Server

    Bohl, T; Garoby, R; Linnecar, Trevor Paul R; Shaposhnikova, Elena; Tückmantel, Joachim

    2003-01-01

    Using long bunches held in place by barrier buckets to overcome the limitations associated with peak density in high intensity bunched beams could be a promising scheme for increasing the luminosity of LHC. In the SPS at CERN an initial barrier bucket machine development(MD) study was done in 1999 to check the capabilities of 200 MHz thick barriers generated by the travelling wave system. A second experiment took place on 5th of August 2003 to examine high intensity effects. In this experiment a flat and stable long bunch of @ 3 µs bunch length was obtained and kept for more than 80 minutes without developing a significant line density modulation. However, strong beam loading effects were observed during the injection process, causing a coherent, non-negligible energy transfer from the beam to the RF cavities, and significant fraction of the injected beam was lost to a coasting beam background. The beam intensity that could be confined in between the barriers suffered emittance increase and was not high enou...

  14. Seismic Response of Offshore Wind Structure Supported by Bucket Foundation

    Institute of Scientific and Technical Information of China (English)

    丁红岩; 熊康平; 张浦阳

    2016-01-01

    An integrated finite element model(FEM)of offshore wind tower-foundation-soil is established by ABAQUS, where a large-scale composite bucket foundation with seven compartments inside is applied to support-ing the upper wind tower. The dynamic response of the structure-foundation system is studied under three seismic waves with the same peak ground acceleration of 0.035g. It can be seen that the dynamic response increases at the beginning with the structure height, then it decreases because the structural damping increases due to the mass ef-fect of the upper wind turbine generator system. It is shown that the anti-liquefaction capacity of the soil inside and underneath the foundation is improved owing to the high overburden pressure of the upper structure and the con-straint effect of the bucket skirt and subdivisions. Moreover, the liquefaction resistance of the soil inside the middle compartment is improved to a higher degree than that inside the side compartments.

  15. Bucketing Coding and Information Theory for the Statistical High Dimensional Nearest Neighbor Problem

    CERN Document Server

    Dubiner, Moshe

    2008-01-01

    Consider the problem of finding high dimensional approximate nearest neighbors, where the data is generated by some known probabilistic model. We will investigate a large natural class of algorithms which we call bucketing codes. We will define bucketing information, prove that it bounds the performance of all bucketing codes, and that the bucketing information bound can be asymptotically attained by randomly constructed bucketing codes. For example suppose we have n Bernoulli(1/2) very long (length d-->infinity) sequences of bits. Let n-2m sequences be completely independent, while the remaining 2m sequences are composed of m independent pairs. The interdependence within each pair is that their bits agree with probability 1/20. Moreover if one sequence out of each pair belongs to a a known set of n^{(2p-1)^{2}-\\epsilon} sequences, than pairing can be done using order n comparisons!

  16. Investigation of seepage around the bucket skirt during installation in sand

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo

    First aim of this study is to evaluate a pore pressure factor, . The factor describes the ratio between the excess pore pressure generated on the bucket tip and the applied suction under the bucket lid. The pore pressure factor can be then used for prediction of excess pore pressure at the tip...... or along bucket skirt with known soil condition, bucket geometry and applied suction. The second aim of the study is to evaluate expressions for normalized seepage length, s/h, for different soil combinations and penetration depths. The seepage length is then 7 used to make a prediction of critical...... pressure that will create piping channels at exit, which is near to seabed and to the caisson wall, along bucket wall and at the tip. That is how the limits for suction installation can be assumed. Finally, the critical suction is used for predicting the reduction of penetration resistance and the method...

  17. Investigation of seepage around the bucket skirt during installation in sand

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo

    First aim of this study is to evaluate a pore pressure factor, . The factor describes the ratio between the excess pore pressure generated on the bucket tip and the applied suction under the bucket lid. The pore pressure factor can be then used for prediction of excess pore pressure at the tip...... or along bucket skirt with known soil condition, bucket geometry and applied suction. The second aim of the study is to evaluate expressions for normalized seepage length, s/h, for different soil combinations and penetration depths. The seepage length is then 7 used to make a prediction of critical...... pressure that will create piping channels at exit, which is near to seabed and to the caisson wall, along bucket wall and at the tip. That is how the limits for suction installation can be assumed. Finally, the critical suction is used for predicting the reduction of penetration resistance and the method...

  18. Seepage Study for Suction Installation of Bucket Foundation in Different Soil Combinations

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo; Clausen, Johan Christian

    2016-01-01

    Research has proven the bucket foundation to be a feasible and an attractive solution for offshore wind turbines. Its potential derives partly from the cost-effectiveness due to the suction-assisted installation. The suction applied under the bucket lid produces a downward driving force...... solutions. A series of numerical simulations performed on the flow analysis around the bucket penetrating into sand are presented in this paper. The characteristics of seepage arising from applied suction are investigated. The cases included in the research cover a wide range of bucket dimensions...... around the bucket skirt. The exceedance of critical suction might lead to installation failure due to formation of piping channels, which break the hydraulic seal between the skirt and soil. The excess pore pressure arising due to applied suction changes the effective stress, hence the penetration...

  19. Study of a 3D-Finite Element Calculation of Bucket Foundation

    DEFF Research Database (Denmark)

    André Larsen, Kim; Ibsen, Lars Bo

    2004-01-01

    as the wind turbines are getting larger and more effective. The behaviour of bucket foundations located in saturated dense sand has been investigated by use of model tests. One of the methods to predict the response of a full size bucket foundation is the Finite Element Method, FEM. This method has been used......The bucket foundation is a new type of foundation, which has been developed over the past 3 years and today it is used for a Vestas V90-3.0 MW offshore wind turbine as a prototype. Ibsen et al.(2003). The bucket foundation is believed to have great potential in the future offshore wind parks...... to back calculate the response of the model tests in the laboratory. It has been shown that a three-dimensional Finite Element model is a useful method to predict the behaviour of bucket foundations for offshore wind turbines installed in saturated sand....

  20. Impact of paint matrix composition and thickness of paint layer on the activity of photocatalytic paints

    Directory of Open Access Journals (Sweden)

    Homa Piotr

    2017-03-01

    Full Text Available Silicate, acrylic and latex photocatalytic paints were analyzed in regards to impact of paint matrix composition and paint layer’s thickness on performance in two photocatalytic tests. These included performances in photocatalytic decomposition of benzo[a]pyrene (BaP and assessment of photocatalytic activity through use of smart ink test. Silicate photocatalytic paints displayed lower photocatalytic activity in comparison to acrylic and latex photocatalytic paints in both tests, despite the similar content of nanocrystalline TiO2. Measurements of depth of UV light penetration through the paints layer were performed and it appeared, that more porous structure of coating resulted in deeper penetration of UV light. In the case of acrylic paint, the thickness of the photocatalytic layer was around 9 μm, but for silicate paint DR this thickness was higher, around 21 μm.

  1. Paint it nanoblack

    Science.gov (United States)

    Perkowitz, Sidney

    2016-08-01

    Ever since our ancestors painted images on the walls of caves, artists have sought pigments to represent the 10 million tints that humans can differentiate. Now they have a new ally: researchers who are using optical design principles, nanotechnology and inspiration from nature to create deeper blacks and purer whites.

  2. Improved Paint Removal Technique

    Science.gov (United States)

    1978-04-25

    4 (Phenol)1: p1P4 ji:i Condition of Point Surface Condition of Paint: Surface 4 after 45 minutes ufter 25 minutes Ten~t Pronsidure No. I. on~ Tent ...the ,.I .- pit so high velume water flow can be used to flush the pit floor clean at I the end of each day. Installation of removable grating is also

  3. Painting Cloth with Crayons.

    Science.gov (United States)

    Asch, Rosalie L.

    1979-01-01

    Painting cloth with crayons is suggested as a challenging art project, especially for students who have difficulty with the complex tools and processes typical of more advanced textile work. Instructions are given for creating decorative banners with this technique. One of seven articles in this issue on fiber arts. (Author/SJL)

  4. Artists Paint ... Fantasy

    Science.gov (United States)

    Herberholz, Barbara

    2012-01-01

    When he painted a portrait of Holy Roman Emperor Rudolph II (1552-1612), Giuseppe Arcimboldo used his imagination, and portrayed him as "Vertumnus," the Roman god of vegetation and the seasons. It's fun to find the different fruits, vegetables and flowers he used: pea-pod eyelids, a gourd for the forehead. Court painters of the time usually…

  5. Rabbit Repellent Paint

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Five gallons of rabbit repellent paint were sent to George Wilson to be applied on the trees of the Tewaukon tree plot. Mr. Wilson requires a 3 or 4 in. brush for...

  6. The Farmers’ Woodcut Paintings

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Folk art is not constrained by scholastic regulations such as proportion and perspective. Taking rural life as their subject matter, farmers from the Hubei mountains by the Yangtze River’s Xiling Gorge create woodcut paintings with a humorous and unpretentious charm. Recently, more than a hundred works created by these farmer painters were exhibited in the China Art Gallery in Beijing.

  7. Lined canvas paintings

    DEFF Research Database (Denmark)

    Krarup Andersen, Cecil

    2013-01-01

    and tensile testing samples from the tacking edges as well as lined mock-up samples. The ability of the different lining techniques to support canvas paintings is evaluated in terms of their initial stretching and during fluctuations of relative humidity. Six different combinations of lining adhesives...

  8. Judgement of abstract paintings

    Directory of Open Access Journals (Sweden)

    Dakulović Sandra

    2006-01-01

    Full Text Available In two experiments the judgement of twenty one abstract paintings was investigated. In Experiment 1, subjects were asked to make similarity judgements of 210 pairs of paintings on a 7 step bipolar scale (similar-dissimilar. The Multi-dimensional scaling (MDS method was used for data analysis. The distribution of paintings within MDS 2-D space suggested two grouping criteria: colorfullness (e.g. from Klee to Kline and geometrization (e.g. from Vasarely to Kandinsky. In Experiment 2, subjects were asked to judge the same paintings on three factors of the instrument SDF 9 (Marković et al., 2002b: Evaluation, Arousal and Regularity. The purpose of this experiment was to specify the subjective criteria on which the (dissimilarity judgements were based. In the regression analysis the three factors of SDF 9 were defined as predictors, whereas the x and y coordinates of MDS 2-D space were defined as dependent variables. The results have shown that the dimension x was reducible to the Evaluation factor, and dimension y is reducible to the Regularity factor.

  9. Painting for public perception

    Energy Technology Data Exchange (ETDEWEB)

    Collison, M.

    2011-12-15

    This paper presents the work of a wildlife artist, Lucas Seaward, in eliciting public opinion on the oilsands industry. He is in the process of creating 20 or more paintings using oil on canvas, not the Chagall or van Gogh sort of oil, but bitumen extracted near Fort McMurray. The paintings are designed for an exhibition to travel across Canada. His aim is to spread awareness that the oilsands industry is working hard towards sustainability and the protection of wildlife. Apart from being evil-smelling, bitumen is stiff, it does not dry quickly, and it wears out paint brushes really fast. Similarly to producers who add a diluent for proper flow, Seaward also found an additive that allowed smooth flow so that he could paint the bitumen in thin layers that dried properly and also was able to produce gradations of color. The idea is to educate the general public out of his personal experience of Fort McMurray and the oilsands industry.

  10. Direct electroplating of plastic for advanced electrical applications

    DEFF Research Database (Denmark)

    Islam, Aminul; Hansen, Hans Nørgaard; Tang, Peter Torben

    2017-01-01

    for direct electroplating of plastic eliminating the need for slow and expensive processes like electroless metal deposition, PVD coating, painting with conductive inks etc. The results obtained from the test demonstrate the potential of direct electroplating of plastic to enhance the electrical conductivity...... and the use of electroplated plastics for advanced applications like Moulded Interconnect Devices (MIDs)....

  11. Experimental Study of Pore Pressure and Deformation of Suction Bucket Foundations Under Horizontal Dynamic Loading

    Institute of Scientific and Technical Information of China (English)

    LU Xiao-bing; WANG Shu-yun; ZHANG Jian-hong; SUN Guo-liang; SHI Zhong-min

    2005-01-01

    Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefaction index (excess pore pressure divided by initial effective stress. In this paper, the developmental degree of excess pore pressure is described by liquefaction index) decreases from the upper part to the lower part of the sand foundation in the vertical direction and decreases from near to far away from the bucket′s side wall in the horizontal direction. Large settlements of the bucket and the sand around the bucket are induced by the horizontal dynamic loading. The dynamic responses of the bucket of a smaller height (when the diameter is the same) are heavier. A cyclic crack some distance near the bucket occurs in the sand.

  12. Comparison of Calculation Models for Bucket Foundation in Sand

    DEFF Research Database (Denmark)

    Vaitkunaite, Evelina; Molina, Salvador Devant; Ibsen, Lars Bo

    The possibility of fast and rather precise preliminary offshore foundation design is desirable. The ultimate limit state of bucket foundation is investigated using three different geotechnical calculation tools: [Ibsen 2001] an analytical method, LimitState:GEO and Plaxis 3D. The study has focused...... on resultant bearing capacity of variously embedded foundation in sand. The 2D models, [Ibsen 2001] and LimitState:GEO can be used for the preliminary design because they are fast and result in a rather similar bearing capacity calculation compared with the finite element models of Plaxis 3D. The 2D models...... and their results are compared to the finite element model in Plaxis 3D in this article....

  13. Prototype bucket foundation for wind turbines - natural frequency estimation

    Energy Technology Data Exchange (ETDEWEB)

    Ibsen, Lars Bo; Liingaard, M.

    2006-12-15

    The first full scale prototype bucket foundation for wind turbines has been installed in October 2002 at Aalborg University offshore test facility in Frederikshavn, Denmark. The suction caisson and the wind turbine have been equipped with an online monitoring system, consisting of 15 accelerometers and a real-time data-acquisition system. The report concerns the in service performance of the wind turbine, with focus on estimation of the natural frequencies of the structure/foundation. The natural frequencies are initially estimated by means of experimental Output-only Modal analysis. The experimental estimates are then compared with numerical simulations of the suction caisson foundation and the wind turbine. The numerical model consists of a finite element section for the wind turbine tower and nacelle. The soil-structure interaction of the soil-foundation section is modelled by lumped-parameter models capable of simulating dynamic frequency dependent behaviour of the structure-foundation system. (au)

  14. GENETIC PROGRAMMING TO PREDICT SKI-JUMP BUCKET SPILLWAY SCOUR

    Institute of Scientific and Technical Information of China (English)

    AZAMATHULLA H. MD; GHANI A. AB; ZAKARIA N. A; LAI S. H; CHANG C. K; LEOW C. S; ABUHASAN Z

    2008-01-01

    Researchers in the past had noticed that application of Artificial Neural Networks (ANN) in place of conventional statistics on the basis of data mining techniques predicts more accurate results in hydraulic predictions. Mostly these works pertained to applications of ANN. Recently, another tool of soft computing, namely, Genetic Programming (GP) has caught the attention of researchers in civil engineering computing. This article examines the usefulness of the GP based approach to predict the relative scour depth downstream of a common type of ski-jump bucket spillway. Actual field measurements were used to develop the GP model. The GP based estimations were found to be equally and more accurate than the ANN based ones, especially, when the underlying cause-effect relationship became more uncertain to model.

  15. Capacities and failure modes of suction bucket foundation with internal bulkheads

    Science.gov (United States)

    Xiao, Zhong; Ge, Borui; Wang, Yan

    2017-08-01

    Suction bucket foundations can be divided into four compartments by cruciform internal bulkheads, thereby yielding better capacity in certain conditions than those without internal bulkheads. As yet, no systematic study has been conducted regarding the effects of cruciform internal bulkheads on the capacities of suction bucket foundations. In this study, we established a large number of finite element models of suction bucket foundations with and without cruciform internal bulkheads and of solid embedded circular foundations. We found the uniaxial capacities and failure modes of suction bucket foundations with various depth ratios to remain basically unaffected by internal bulkheads in uniform clays. However, in inhomogeneous clay with high strength heterogeneity, we observed the uniaxial moment and horizontal capacities and corresponding failure modes of suction bucket foundations with a low depth ratio to be obviously affected by internal bulkheads. In this case, the uniaxial moment capacities, in particular, as well as the horizontal capacities of suction bucket foundations with cruciform internal bulkheads become obviously greater than those without internal bulkheads. Under combined loading, we found the failure envelopes of suction bucket foundations with and without cruciform internal bulkheads and of solid circular foundation to also be basically consistent in uniform clays. However, in inhomogeneous clay with high strength heterogeneity, cruciform internal bulkheads can obviously change the shapes of the failure envelopes of bucket foundations with a small depth ratio. We conclude that when the acting vertical load or foundation depth is relatively small, suction bucket foundations with cruciform internal bulkheads can be subjected to larger moment and horizontal loads in soft clays with high strength heterogeneity.

  16. Modified Expression for the Failure Criterion of Bucket Foundations Subjected to Combined Loading

    DEFF Research Database (Denmark)

    Larsen, Kim André; Ibsen, Lars Bo; Barari, Amin

    2013-01-01

    Recently, various loading tests with small- and large-scale bucket foundations were performed on buckets of varying sizes, embedment ratios, and load paths with saturated dense Aalborg University Sand No. 1 at the geotechnical laboratory of Aalborg University. In the present study, the capacity...... and behavior of bucket foundations subjected to combined loads were investigated on the basis of the results of these experimental studies. Although previous authors had proposed a linear relationship between the moment capacity and the vertical load, this relationship did not fit the observed capacities...

  17. Buckling Analysis of Bucket Foundations for Wind Turbines in Deep Water

    DEFF Research Database (Denmark)

    Madsen, Søren; Andersen, Lars; Ibsen, Lars Bo

    2011-01-01

    Using large suction caissons for offshore wind turbines is an upcoming technology also referred to as bucket foundations. The bucket foundation does not require heavy installation equipment, but since it is constructed as a thin steel shell structure, instability, in form of buckling, becomes...... a crucial issue during installation. This paper addresses the hydrostatic buckling pressure of the bucket foundation using threedimensional, non-linear finite element analysis. The main finding of this paper is that introducing an imperfect geometry based on the first linear pre-buckling mode shape, can...... increase the buckling load significantly....

  18. Reducer Selection When Doing Overall Paint Jobs Using Enamel Paints. Lesson Plan No. 1 of Auto Repair and Painting.

    Science.gov (United States)

    Tyau, Layton M.

    This lesson, which is part of a high school course in auto body repair and painting, deals with selecting a reducer when doing overall paint jobs using enamel paints. Students are taught the general properties of different types of enamel paints and selection of the proper reducer for each type of paint, depending on the weather and the specific…

  19. Reducer Selection When Doing Overall Paint Jobs Using Enamel Paints. Lesson Plan No. 1 of Auto Repair and Painting.

    Science.gov (United States)

    Tyau, Layton M.

    This lesson, which is part of a high school course in auto body repair and painting, deals with selecting a reducer when doing overall paint jobs using enamel paints. Students are taught the general properties of different types of enamel paints and selection of the proper reducer for each type of paint, depending on the weather and the specific…

  20. Plastic Surgery

    Science.gov (United States)

    ... Surgery? A Week of Healthy Breakfasts Shyness Plastic Surgery KidsHealth > For Teens > Plastic Surgery Print A A ... forehead lightened with a laser? What Is Plastic Surgery? Just because the name includes the word "plastic" ...

  1. The Transdisciplinary Potential of Remediated Painting

    DEFF Research Database (Denmark)

    Petersen, Anne Ring

    2010-01-01

    Over the last decades the notion of what painting is has been considerably widened due to intermediality, i.e. crossovers between artistic media such as painting and sculpture, painting and photography, painting and installation, painting and performance etc. This paper suggests that the transfor...

  2. Shang Yang’s Paintings

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Shang yang is a highly representative painter in the contemporary Chinese oil painting circle. In the past few decades, his painting style has changed several times; he abandoned his successful original style and familiar subjects when he turned from realism to abstraction. In the two pieces shown here, the people of the Loess Plateau are depicted as existing as an integral whole with nature, mutually inside and outside of it. Beholden to some techniques from traditional Chinese painting Shang’s

  3. Method of Assessment of Hard Rock Workability using Bucket Wheel Excavators

    Science.gov (United States)

    Machniak, Łukasz; Kozioł, Wiesław

    2017-03-01

    A new hypothesis concerning a process of the mining solid rocks using bucket wheel excavators (BWE). Destroying of the rock mass structure is a result of breaking and not, as so far accepted, of cutting. This approach excludes, for the description of solid rock workability using bucket wheel excavators, used classifications based on individual linear or surface resistances of cutting. The possibility of a replacement mechanism for determining of the workability by bucket wheel excavators using rippers was assumed. On this basis, an innovative method for assessing the workability of solid rocks was developed, which is a combination of an derived empirical energy relationship LSE of breaking by tractor rippers from a compressive strength, a seismic wave velocity, a density of solid rock, and the modified classification of workability by bucket wheel excavators according to Bulukbasi (1991). The proposed method allows for multi-parameter assessment of the workability class based on the parameters that are independent variables in the specified dependencies.

  4. Climate Prediction Center (CPC) Global Monthly Leaky Bucket Soil Moisture Analysis

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Monthly global soil moisture, runoff, and evaporation data sets produced by the Leaky Bucket model at 0.5? ? 0.5? resolution for the period from 1948 to the present....

  5. Experience with the RK 5000 bucket chain excavator. Iskustva iz pogona stroja RK 5000

    Energy Technology Data Exchange (ETDEWEB)

    Madry, F.

    1988-01-01

    Highlights technical features of the RK 5000 bucket chain excavator manufactured by the Czechoslovak Vitkovice concern on the basis of the RK-400 excavator. Capacity of the RK-5000 excavator ranges from 3600-4500 m/sup 3//h depending on chain velocity and on the properties of excavated material. Capacity of 5,000 m/sup 3//h was also achieved by overloading the buckets by 12%. The pulling force of the bucket chain is 220 t (excess force of up to 330 t was also achieved for short periods). The working heights (or working depth) may reach 2 m. Bucket volume is 3,650 l. The installed power of the RK-5000 excavator is 2x1,600 kW. Experience gained during trial operation of the RK-5000 excavator in loose soil, and subsequent technical improvements made are presented.

  6. Gated current integrator for the beam in the RR barrier buckets

    Energy Technology Data Exchange (ETDEWEB)

    A. Cadorn; C. Bhat; J. Crisp

    2003-06-10

    At the Fermilab Recycler Ring (RR), the antiproton (pbar) beam will be stored azimuthally in different segments created by barrier buckets. The beam in each segment may have widely varying intensities. They have developed a gated integrator system to measure the beam intensity in each of the barrier bucket. Here they discuss the design of the system and the results of beam measurements using the integrator.

  7. SIMULATION OF THE ATOMIZED FLOW BY SLIT TYPE BUCKET ENERGY DISSIPATOR

    Institute of Scientific and Technical Information of China (English)

    LIU Shi-he; DUAN Hong-dong

    2005-01-01

    Slit type bucket is one kind of flip bucket for energy dissipation generally used in the hydraulic project.In this paper the atomized flow produced behind this energy dissipator is analyzed, a numerical model for the aerated jet considering air entrainment and air resistance force is suggested, and simulation of the rain resulted by the atomized flow is also discussed.Furthermore, the prototype observation data for the atomized flow of Dongjiang Hydropower Station is used to verify the model suggested.

  8. Analysis of Bearing Capacity of Suction Bucket Foundation Subjected to Horizontal and Moment Loadings

    OpenAIRE

    W.U. Ke; M.A. Mingyue

    2013-01-01

    The suction bucket foundation is not only supporting the vertical loading such as the sea platform and weight itself, but also subjecting to horizontal and moment loading due to wind and wave. The response of bucket foundation to combined Horizontal (H) and Moment (M) loading has been studied using 3D finite element analysis Then the proposed method is numerically implemented in the framework of the general-purpose FEM software ABAQUS. Relationship curve between the coefficient of ultimate be...

  9. Forces acting on particles in a Pelton bucket and similarity considerations for erosion

    Science.gov (United States)

    Rai, A. K.; Kumar, A.; Staubli, T.

    2016-11-01

    High sediment transport rates cause severe erosion issues in hydropower plants leading to interruptions in power generation, decrease in efficiency and shutdown for repair and maintenance. For Pelton turbines operating at high head, the issue of erosion is severe, especially in components like buckets, nozzle rings and needles. Goal of the study is to develop erosion focussed guidelines for both designing as well as operating hydropower plants with Pelton runners. In this study, the flow of sediment inside a Pelton bucket with respect to forces acting on solid particles is analysed with an analytical approach by considering different dynamic forces originating from the rotation of the turbine, the curvature of the buckets, and the Coriolis effect. Further, the path of sediment particles and its effect on erosion phenomena are analysed based on the process of separation of different sized sediment particles from streamlines. The data relating to head, power, discharge, number of jet and efficiency of 250 hydropower plants installed all over the world were analysed in this study to find the major factors related to erosion in Pelton turbine bucket. From analysis of different force ratios, it is found that an increase of D/B, i.e. the ratio of pitch circle diameter and bucket width, and/or decrease of specific speed (nq) enhances erosion. As the erosion process depends significantly on nondimensional parameters D/B and nq, these are considered as similarity measures for scaling of the erosion process in the Pelton buckets of various sizes.

  10. LOVE AESTHETICS AND PAINTING

    Directory of Open Access Journals (Sweden)

    ZUhal ARDA

    2015-04-01

    Full Text Available Talking about love, while we are talking about a culture and world view means. People love for the people, the passion that inhabited the earth of mankind, the "love" for the first time since love always makes life meaningful emotions has been replaced in the front row between. Throughout history, many artists, scientist, philosopher, and polymath has committed about love are in the works. Poetry, music, theatre, dance, painting, sculpture, each with its own specific language, an art form they are given immortal works about love. Sense of friendship and love of antiquity, Medieval spiritual journeys, when more stunning and dramatic to modern times, trends, human love, to the concept of gaining various dimensions of divine love. Understanding by seeing through these exchanges pictures-meaning maybe the concept of "love" will shed light on the changing values, too. When you do this, both from the east and from the west, giving examples to do a comparison over the years has diversified, changing the concept of "love" art of painting will be an indication that reflected how.

  11. Laser assisted graffiti paints removing

    Science.gov (United States)

    Novikov, B. Y.; Chikalev, Y. V.; Shakhno, E. A.

    2011-02-01

    It's hard to imagine a modern city view without some drawings and inscriptions, usually called "graffiti". Traditional cleaning methods do not suit modern requirements. Investigation of possibilities of laser assisted paints removing is described in this article. The conditions for removing different paints from different surfaces were defined.

  12. Microscale radiocarbon dating of paintings

    Science.gov (United States)

    Hendriks, Laura; Hajdas, Irka; McIntyre, Cameron; Küffner, Markus; Scherrer, Nadim C.; Ferreira, Ester S. B.

    2016-03-01

    In this paper, radiocarbon dating of paintings using minimal sample sizes has been investigated, in an effort to address the problem of limited access to sample material in paintings. 14C analyses were conducted on signed and dated paintings from two Swiss artists of the twentieth century. The selected paintings dated from the 1930s and 1960s, provided the opportunity to evaluate the dating accuracy on paintings realized before and after 1950 AD when the 14C bomb peak was created, as a result of the nuclear tests conducted in the 1950/1960s. The work focused on the one hand on minimizing the size of the canvas sample required for accelerator mass spectrometer radiocarbon measurement on the gas ion source of the MICADAS and, on the other hand, on testing the possibility of dating the organic binder of the paint. Following careful characterization of the paint composition by X-ray fluorescence spectroscopy, Fourier transformed infrared spectroscopy, and Raman spectroscopy, paints containing no other carbon source than the natural organic binder were identified and dated.

  13. Neural correlates of viewing paintings

    DEFF Research Database (Denmark)

    Vartanian, Oshin; Skov, Martin

    2014-01-01

    Many studies involving functional magnetic resonance imaging (fMRI) have exposed participants to paintings under varying task demands. To isolate neural systems that are activated reliably across fMRI studies in response to viewing paintings regardless of variation in task demands, a quantitative...

  14. Microscale radiocarbon dating of paintings

    Energy Technology Data Exchange (ETDEWEB)

    Hendriks, Laura; Hajdas, Irka; McIntyre, Cameron [ETH Zurich, Ion Beam Physics, Zurich (Switzerland); Kueffner, Markus; Ferreira, Ester S.B. [SIK-ISEA, Zurich, Zurich (Switzerland); Scherrer, Nadim C. [Bern University of Applied Sciences, HKB, Bern (Switzerland)

    2016-03-15

    In this paper, radiocarbon dating of paintings using minimal sample sizes has been investigated, in an effort to address the problem of limited access to sample material in paintings. {sup 14}C analyses were conducted on signed and dated paintings from two Swiss artists of the twentieth century. The selected paintings dated from the 1930s and 1960s, provided the opportunity to evaluate the dating accuracy on paintings realized before and after 1950 AD when the {sup 14}C bomb peak was created, as a result of the nuclear tests conducted in the 1950/1960s. The work focused on the one hand on minimizing the size of the canvas sample required for accelerator mass spectrometer radiocarbon measurement on the gas ion source of the MICADAS and, on the other hand, on testing the possibility of dating the organic binder of the paint. Following careful characterization of the paint composition by X-ray fluorescence spectroscopy, Fourier transformed infrared spectroscopy, and Raman spectroscopy, paints containing no other carbon source than the natural organic binder were identified and dated. (orig.)

  15. Yang Hua's Modern Chinese Painting

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Yang Hua, a female painter from Hainan Province forms her style of modern Chinese painting with an original, exotic and ingenious means of artistic expression. Full of vigor, her paintings convey intimacy among human beings. She expresses her feelings towards nature and society through her dimly visible and disorderly pictures. The harmony of abstract and

  16. Breast Cancer in Art Painting

    OpenAIRE

    2011-01-01

    Breast cancer is an emotive cancer. It is a disease that affects a visible sexual organ and it is the commonest single cause of death of women between 40 and 60 years of age. Nevertheless, this type of cancer was infrequently depicted in art paintings. In this article the themes from the breast cancer in famous art paintings are discussed.

  17. Bucket Brigades to Increase Productivity in a Luxury Assembly Line

    Directory of Open Access Journals (Sweden)

    Filippo De Carlo

    2013-08-01

    Full Text Available One of the most challenging issues in manual assembly lines is to achieve the best balance of workloads. There are many analytic approaches to solve this problem, but they are often neglected, since they are time-consuming and require high level engineering skills. Fashion bags packaging lines must comply with a number of different products with low production volumes, while the organization of the line is often under the mere responsibility of the foreman, who balances workloads in an empirical way. The aim of this work is to evaluate the effectiveness of the arrangement of bucket brigades (BBs for an assembly line of luxury handbags. To do this, it was decided to perform a testing activity in a company producing fashion handbags in order to compare the self-made design with the BBs and with a simple assembly line balancing problem algorithm. The originality of this research lies in the fact that there are no studies in the literature on BBs applied to the packaging of highly variable small batches. The results were excellent, showing the advantages of BBs in terms of flexibility, the reduction of work in the process and the ability to handle small anomalies.

  18. Jumping into buckets, or How to decontaminate overlapping fat jets

    CERN Document Server

    Hamaguchi, Koichi; Stoll, Martin

    2015-01-01

    At the LHC, tagging boosted heavy particle resonances which decay hadronically, such as top quarks and Higgs bosons, can play an essential role in new physics searches. In events with high multiplicity, however, the standard approach to tag boosted resonances by a large-radius fat jet becomes difficult because the resonances are not well-separated from other hard radiation. In this paper, we propose a different approach to tag and reconstruct boosted resonances by using the recently proposed mass-jump jet algorithm. A key feature of the algorithm is the flexible radius of the jets, which results from a terminating veto that prevents the recombination of two hard prongs if their combined jet mass is substantially larger than the masses of the separate prongs. The idea of collecting jets in "buckets" is also used. As an example, we consider the fully hadronic final state of pair-produced vectorlike top partners at the LHC, $pp\\to T\\bar{T}\\to t\\bar{t}HH$, and show that the new approach works better than the corr...

  19. The Conservation of Panel paintings

    DEFF Research Database (Denmark)

    Until the early 17th century almost all portable paintings were created on wood supports, including masterpieces by famous painters, ranging from Giotto to Dürer to Rembrandt. The structural conservation of these paintings requires specific knowledge and skills as the supports are susceptible...... to damage caused by unstable environmental conditions. Unfortunately, past structural interventions often caused significant damage due to insufficient knowledge of the behaviour of the wood panels, glue and paint layers. Over the last fifty years, the field has developed treatment strategies based......, it is imperative to strengthen scientific research into the production methods, ageing and future behaviour of panel paintings, being an intricate interplay between different materials. A deeper understanding of the processes that adversely affect panel paintings over time will contribute to the improved care...

  20. Bucket-handle meniscal tears of the knee: sensitivity and specificity of MRI signs

    Energy Technology Data Exchange (ETDEWEB)

    Dorsay, Theodore A.; Helms, Clyde A. [Department of Radiology, Duke University Medical Center, Erwin Road, Room 1504, NC 27710, Durham (United States)

    2003-05-01

    To determine the sensitivity and specificity of reported MRI signs in the evaluation of bucket-handle tears of the knee.Design and patients A retrospective analysis of 71 knee MR examinations that were read as displaying evidence of a bucket-handle or ''bucket-handle type'' tear was performed. We evaluated for the presence or absence of the absent bow tie sign, the coronal truncation sign, the double posterior cruciate ligament (PCL) sign, the anterior flipped fragment sign, and a fragment displaced into the intercondylar notch. Sensitivity and specificity were calculated relative to the gold standard of arthroscopy. Forty-three of 71 cases were surgically proven as bucket-handle tears. The absent bow tie sign demonstrated a sensitivity of 88.4%. The presence of at least one of the displaced fragment signs had a sensitivity of 90.7%. A finding of both the absent bow tie sign and one of the displaced fragment signs demonstrated a specificity of 85.7%. The double PCL sign demonstrated a specificity of 100%. The anterior flipped meniscus sign had a specificity of 89.7%. Bucket-handle tears of the menisci, reported in about 10% of most large series, have been described by several signs with MRI. This report gives the sensitivity and specificity of MRI for bucket-handle tears using each of these signs independently and in combination. MRI is shown to be very accurate for diagnosing bucket-handle tears when two or more of these signs coexist. (orig.)

  1. Painting and Writing Matters

    DEFF Research Database (Denmark)

    Balle, Søren Hattesen

    2006-01-01

    Collaborative work between painters and writers was a common activity among the New York School poets in the 1950s. Its popularity was a combined result of circumstance and choice. Artistic collaboration served Frank O’Hara and his New York School colleagues in their attempt to escape from...... the academic orthodoxies of New Criticism, the latter decreeing the autonomy of poetry and the harmonious integration of form and content in a signifying poetic whole. By experimenting with the interplay between poetry and other artistic genres, their collaborations with painters seriously tested the limits....... This double strategy contributes to a re-inscription of poetry and painting as sheer physical matter and means of artistic production within that world which they purport to represent in the first place. Thus, it seeks to point to the complicity of both genres in the material processes of cultural production...

  2. The Conservation of Panel paintings

    DEFF Research Database (Denmark)

    Until the early 17th century almost all portable paintings were created on wood supports, including masterpieces by famous painters, ranging from Giotto to Dürer to Rembrandt. The structural conservation of these paintings requires specific knowledge and skills as the supports are susceptible...... to damage caused by unstable environmental conditions. Unfortunately, past structural interventions often caused significant damage due to insufficient knowledge of the behaviour of the wood panels, glue and paint layers. Over the last fifty years, the field has developed treatment strategies based...

  3. Bucket wheel rehabilitation of ERC 1400-30/7 high-capacity excavators from lignite quarries

    Science.gov (United States)

    Vîlceanu, Fl; Iancu, C.

    2016-11-01

    The existence of bucket wheel equipment type ERC 1400-30/7 in lignite quarries with lifetime expired, or in the ultimate life period, together with high cost investments for their replacement, makes rational the efforts made to rehabilitation in order to extend their life. Rehabilitation involves checking operational safety based on relevant expertise of metal structures supporting effective resistance but also the replacement (or modernization) of subassemblies that can increase excavation process productivity, lowering energy consumption, reducing mechanical stresses. This paper proposes an analysis of constructive solution of using a part of the classical bucket wheel, on which are located 9 cutting cups and 9 chargers cups and adding a new part so that the new redesigned bucket-wheel will contain 18 cutting-chargers cups, compared to the classical model. On the CAD model of bucket wheel was performed a static and a dynamic FEA, the results being compared with the yield strength of the material of the entire structure, were checked mechanical stresses in the overall distribution map, and were verified the first 4 vibrating modes the structure compared to real loads. Thus was verified that the redesigned bucket-wheel can accomplish the proposed goals respectively increase excavation process productivity, lowering energy consumption and reducing mechanical stresses.

  4. Double and triple-harmonic RF buckets and their use for bunch squeezing in AGS

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, C. J. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-08-24

    For the past several years we have merged bunches in AGS in order to achieve the desired intensity per bunch prior to injection into RHIC. The merging is done on a at porch at or above AGS injection energy. Because the merges involve the reduction of the RF harmonic number by a factor of 2 (for a 2 to 1 merge) and then a factor of 3 (for a 3 to 1 merge), one requires RF frequencies 6hfs, 3hfs, 2hfs and hfs, where fs is the revolution frequency on the porch and h = 4 is the fundamental harmonic number. The standard AGS RF cavities cannot operate at the lowest frequencies 2hfs and hfs; these are provided by two modi ed cavities. Upon completion of the merges, the bunches are sitting in harmonic h buckets. In order to be accelerated they need to be squeezed into harmonic 3h buckets. This is accomplished by producing a double-harmonic bucket in which harmonics h and 2h act in concert, and then a triple-harmonic bucket in which harmonics h, 2h, and 3h act in concert. Simulations have shown that the squeeze presents an acceptance bottleneck which limits the longitudinal emittance that can be put into the harmonic 3h bucket.

  5. Literature review on cyclic lateral loading effects of mono-bucket foundations

    DEFF Research Database (Denmark)

    Kapitanov, Lachezar Rosenov; Duroska, Peter; Garcia, Cesar Antonio Garcia

    2016-01-01

    The renewable offshore energy sector is currently growing rapidly and there is a vast interest in optimization of the design procedures for the offshores wind turbines. Mono-Bucket can be a breakthrough in the sphere of offshore wind turbines foundations due to its lightness and fast installation...... and consequently cost-effectiveness compared to other common solutions. The long-term cyclic loading can cause degradation of soil-bucket system stiffness, which yields into accumulated and permanent deformations. Despite of the advantages, there is no standard procedure to design the foundation especially...... for assessing the accumulated deformations under environmental longterm loading. However, numerical and semi-empirical methods already used for offshore foundations can be adopted to take into account the effect of cyclic loading on Mono-Buckets. Among them, load-displacement techniques as cyclic p-y curves...

  6. Injection method of barrier bucket supported by misaligned electron cooling for CRing

    CERN Document Server

    Shen, Guo-Dong; Xia, Jia-Wen; Mao, Li-Jun; Yin, Da-Yu; Chai, Wei-Ping; Shi, Jian; Sheng, Li-Na; Smirnov, A; Wu, Bo; Zhao, He

    2016-01-01

    A new accelerator complex HIAF (the High Intensity Heavy Ion Accelerator Facility) is approved in China. It is designed to provide intense primary and radioactive ion beams for researches in high energy density physics, nuclear physics, atomic physics as well as other applications. In order to achieve a high intensity up to 5e11ppp 238U34+, CRing needs to stack more than 5 bunches transferred from BRing. However, the normal bucket to bucket injection scheme can only achieve an intensity gain of 2, so an injection method, fixed barrier bucket (BB) supported by electron cooling, is proposed. To suppress the severe space charge effect during the stacking process, misalignment is adopted in the cooler to control the transverse emittance. In this paper the simulation and optimization with BETACOOL program are presented.

  7. Injection Bucket Jitter Compensation Using Phase Lock System at Fermilab Booster

    Energy Technology Data Exchange (ETDEWEB)

    Seiya, K. [Fermilab; Drennan, C. [Fermilab; Pellico, W. [Fermilab; Chaurize, S. [Fermilab

    2017-05-12

    The extraction bucket position in the Fermilab Booster is controlled with a cogging process that involves the comparison of the Booster rf count and the Recycler Ring revolution marker. A one rf bucket jitter in the ex-traction bucket position results from the variability of the process that phase matches the Booster to the Recycler. However, the new slow phase lock process used to lock the frequency and phase of the Booster rf to the Recycler rf has been made digital and programmable and has been modified to correct the extraction notch position. The beam loss at the Recycler injection has been reduced by 20%. Beam studies and the phase lock system will be discussed in this paper.

  8. Injection method of barrier bucket supported by off-aligned electron cooling for CRing of HIAF

    Science.gov (United States)

    Shen, Guo-Dong; Yang, Jian-Cheng; Xia, Jia-Wen; Mao, Li-Jun; Yin, Da-Yu; Chai, Wei-Ping; Shi, Jian; Sheng, Li-Na; Smirnov, A.; Wu, Bo; Zhao, He

    2016-08-01

    A new accelerator complex, HIAF (the High Intensity Heavy Ion Accelerator Facility), has been approved in China. It is designed to provide intense primary and radioactive ion beams for research in high energy density physics, nuclear physics, atomic physics as well as other applications. In order to achieve a high intensity of up to 5×1011 ppp 238U34+, the Compression Ring (CRing) needs to stack more than 5 bunches transferred from the Booster Ring (BRing). However, the normal bucket to bucket injection scheme can only achieve an intensity gain of 2, so an injection method, fixed barrier bucket (BB) supported by electron cooling, is proposed. To suppress the severe space charge effect during the stacking process, off-alignment is adopted in the cooler to control the transverse emittance. In this paper, simulation and optimization with the BETACOOL program are presented. Supported by New Interdisciplinary and Advanced Pilot Fund of Chinese Academy of Sciences

  9. Plasticity theory

    CERN Document Server

    Lubliner, Jacob

    2008-01-01

    The aim of Plasticity Theory is to provide a comprehensive introduction to the contemporary state of knowledge in basic plasticity theory and to its applications. It treats several areas not commonly found between the covers of a single book: the physics of plasticity, constitutive theory, dynamic plasticity, large-deformation plasticity, and numerical methods, in addition to a representative survey of problems treated by classical methods, such as elastic-plastic problems, plane plastic flow, and limit analysis; the problem discussed come from areas of interest to mechanical, structural, and

  10. Metadata and Buckets in the Smart Object, Dumb Archive (SODA) Model

    Science.gov (United States)

    Nelson, Michael L.; Maly, Kurt; Croom, Delwin R., Jr.; Robbins, Steven W.

    2004-01-01

    We present the Smart Object, Dumb Archive (SODA) model for digital libraries (DLs), and discuss the role of metadata in SODA. The premise of the SODA model is to "push down" many of the functionalities generally associated with archives into the data objects themselves. Thus the data objects become "smarter", and the archives "dumber". In the SODA model, archives become primarily set managers, and the objects themselves negotiate and handle presentation, enforce terms and conditions, and perform data content management. Buckets are our implementation of smart objects, and da is our reference implementation for dumb archives. We also present our approach to metadata translation for buckets.

  11. Implementasi Manajemen Bandwidth Dengan Disiplin Antrian Hierarchical Token Bucket (HTB Pada Sistem Operasi Linux

    Directory of Open Access Journals (Sweden)

    Muhammad Nugraha

    2016-09-01

    Full Text Available Important Problem on Internet networking is exhausted resource and bandwidth by some user while other user did not get service properly. To overcome that problem we need to implement traffic control and bandwidth management system in router. In this research author want to implement Hierarchical Token Bucket algorithm as queue discipline (qdisc to get bandwidth management accurately in order the user can get bandwidth properly. The result of this research is form the management bandwidth cheaply and efficiently by using Hierarchical Token Bucket qdisc on Linux operating system were able to manage the user as we want.

  12. Test Procedure for Axially Loaded Bucket Foundations in Sand (Large Yellow Box)

    DEFF Research Database (Denmark)

    Vaitkunaite, Evelina

    This is a practical guide for preparing the soil, running a CPT test, installing a scaled bucket foundation model and running a test in the large yellow sand box cos(Kristina) in the geotechnical laboratory at Aalborg University. The test procedure is used for the examination of statically...... and cyclically axially loaded bucket foundation model In dense sand. The foundation model in scale of approximately 1:10 compared to the prototype size. The guide describes the step-by-step procedure for tests with and without surface pressure. A detailed description of test setup using the large yellow sand box...

  13. Comparison of numerical formulations for the modeling of tensile loaded suction buckets

    DEFF Research Database (Denmark)

    Sørensen, Emil Smed; Clausen, Johan Christian; Damkilde, Lars

    2017-01-01

    The tensile resistance of a suction bucket is investigated using three different numerical formulations. The first formulation utilizes the three-field u-p-U formulation accounting for solid and fluid displacements, u and U, as well as the pore-fluid pressure, p. The two other formulations comprise...... the simpler u-p formulation in its dynamic and quasi-static form, accounting only for solid displacement and pore-fluid pressure. As basis for comparison, the tensile resistance of a single suction bucket is investigated using a velocity-driven model for a wide range of velocities. It is found, that the quasi...

  14. Painful locking of the knee due to bucket handle tear of mediopatellar plica

    Institute of Scientific and Technical Information of China (English)

    HE Rui; YANG Liu; GUO Lin

    2011-01-01

    A case of swelling and anterior painful knee due to tear of mediopatellar plica is reported. The patient also felt clunk of the patellofemoral joint and knee locking. Under arthroscopic examination, a thick and fibrous plica was found medial to patellar, and a bucket tear along the plica fi.om medial patellar retinaculum to infrapatellar fat pad. Polarized microscopic examination showed collagen fiber fragment and loss of light reflecting property. Neuroimmunohistology suggested up-regulation of synovial plica innervation in the area around the crack. This may be related to the pain. The bucket tear of mediopatellar plicacaused pain and lock of knee are more common than previously reported.

  15. Literature review on cyclic lateral loading effects of mono-bucket foundations

    DEFF Research Database (Denmark)

    Kapitanov, Lachezar Rosenov; Duroska, Peter; Quirante, Cesar Antonio Garcia

    2016-01-01

    calculation is highly demanded at the different design phases. The intention of the current study is to present, review and summarize the existing techniques to assess the effect of cyclic loading on Mono-Bucket foundations while emphasizing the advantage and disadvantage of each of them. Additionally...

  16. Investigation of seepage around the bucket skirt during installation in sand

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo

    pressure that will create piping channels at exit, which is near to seabed and to the caisson wall, along bucket wall and at the tip. That is how the limits for suction installation can be assumed. Finally, the critical suction is used for predicting the reduction of penetration resistance and the method...

  17. A multi-length bunch design for electron storage rings with odd buckets

    Institute of Scientific and Technical Information of China (English)

    ZHU Liang-Jing; LI Wei-Min; WANG Lin; XIANG Dao; HUANG Xiao-Biao

    2015-01-01

    A scheme with two superconducting RF cavities is designed to upgrade electron storage rings with odd buckets to multi-length bunches.In this paper,the Hefei Light Source Ⅱ (HLS Ⅱ) is given as an example for odd buckets.As it is designed for 45 buckets,which is a multiple of 3,simultaneous generation of three different lengths of bunches is proposed with the presently applied user optics.The final result,without low-α optics,is to fill HLS Ⅱ with long bunches of length 50 ps,medium bunches of 23 ps and short bunches of 6 ps.Every third bucket can be filled with short bunches,of which the current limit is up to 6.6 mA,more than 60 times the limit for low-α mode.Moreover,particle tracking simulations to examine the beam dynamics,performed by ELEGANT,and calculations of the beam instabilities are presented in this paper.

  18. Multi-bucket optimization for integrated planning and scheduling in the perishable dairy supply chain

    NARCIS (Netherlands)

    Sel, C.; Bilgen, B.; Bloemhof, J.M.; Vorst, van der J.G.A.J.

    2015-01-01

    This paper considers a dairy industry problem on integrated planning and scheduling of set yoghurt production. A mixed integer linear programming formulation is introduced to integrate tactical and operational decisions and a heuristic approach is proposed to decompose time buckets of the decisions.

  19. Medium-scale Laboratory Installation of Suction Bucket Foundation in Sand

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo

    This report contains a short description of the laboratory set-up followed by a description of the test procedure. Next, tests results are described. In the main part of the report one of each kind of tests is described in detailed. The rests of tests’ detailed descriptions are collected in appen...... the design method for installation of the suction bucket foundation...

  20. A Similitude Theory for Bucket Foundations Under Monotonic Horizontal Load in Dense Sand

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo

    2013-01-01

    This paper aims at finding force-displacement relationships to be employed in the design of bucket foundations for offshore wind turbine. This is accomplished by combining small-scale tests and element tests within a theoretical framework. A similitude theory, regarding the lateral displacement o...

  1. Small-Scale Testing of Laterally Loaded Bucket Foundations in Dense Sand

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Foglia, Aligi

    Monopod bucket foundations promise to become a reliable and cost-effective concept for offshore wind turbine. Physical models are essential to understand the behavior of soil-structure systems. When conducting small-scale experiments on soil, scale effects can considerably affect the tests outcom...

  2. Experimental damping assessment of a full scale offshore mono bucket foundation

    DEFF Research Database (Denmark)

    Gres, Szymon; Fejerskov, Morten; Ibsen, Lars Bo

    2016-01-01

    This paper quantifies the system damping of a offshore meteorological mast supported by a Mono Bucket foundation based on a long-term experimental campaign. The structure is located at Dogger Bank west, North Sea, and equipped with a measurement system monitoring acceleration, strain, inclination...

  3. Multi-bucket optimization for integrated planning and scheduling in the perishable dairy supply chain

    NARCIS (Netherlands)

    Sel, C.; Bilgen, B.; Bloemhof, J.M.; Vorst, van der J.G.A.J.

    2015-01-01

    This paper considers a dairy industry problem on integrated planning and scheduling of set yoghurt production. A mixed integer linear programming formulation is introduced to integrate tactical and operational decisions and a heuristic approach is proposed to decompose time buckets of the decisions.

  4. Dynamic behaviour of mono bucket foundations subjected to combined transient loading

    DEFF Research Database (Denmark)

    Nielsen, Søren Dam; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

    2015-01-01

    This article presents the results from small scale testing, investigating the effect of transient combined loading of a bucketfoundation. The tests are performed inside a pressure tank at Aalborg University, Denmark. The bucket foundation was installed in dense water saturated sand and transient...

  5. Dynamic behaviour of mono bucket foundations subjected to combined transient loading

    DEFF Research Database (Denmark)

    Nielsen, Søren Dam; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

    2015-01-01

    This article presents the results from small scale testing, investigating the effect of transient combined loading of a bucketfoundation. The tests are performed inside a pressure tank at Aalborg University, Denmark. The bucket foundation was installed in dense water saturated sand and transient...

  6. Wave Forces on Transition Pieces for Bucket Foundations for Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia; Andersen, Thomas Lykke; Andersen, Lars Vabbersgaard;

    to a bucket foundation (suction caisson) located at 35 m water depth in the North Sea. Several models of the TPs (wedge-shaped steel flange-reinforced shear panels, conical and doubly curved with or without cutaways) are tested in a wave flume and compared with respect to wave loading. Due to a larger size...

  7. Performance-Based Design Optimization of a Transition Piece for Bucket Foundations for Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia; Andersen, Lars; Ibsen, Lars Bo;

    2011-01-01

    This paper deals with optimization of the shape of the transition piece connecting turbine column with a suction bucket used as a monopod foundation for an offshore wind turbine. The structural behaviour of a transition piece made of compact reinforced composite (CRC) is analysed. Several...

  8. Buckling of Monopod Bucket Foundations – Influence of Boundary Conditions and Soil-structure Interaction

    DEFF Research Database (Denmark)

    Madsen, Søren; Pinna, Rodney; Randolph, M. F.

    2015-01-01

    Using large monopod bucket foundations as an alternative to monopiles for offshore wind turbines offers the potential for large cost savings compared to typical piled foundations. In this paper, numerical simulations are carried out to assess the risk of structural buckling during installation...... is investigated. The effects of including soil restraint and soil–structure interaction on the buckling analysis are also addressed....

  9. Observations on bucket foundations under cyclic loading in dense saturated sand

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Nicolai, Giulio;

    2014-01-01

    Offshore wind farms will play a significant role in the European energy supply of the coming years. Today, one of the main challenges faced by the offshore wind market is to reduce the cost of turbine foundations. The monopod bucket foundation is a possible solution to this problem. The long-term...

  10. Investigations on macro-element modelling of bucket foundations for offshore wind turbines

    DEFF Research Database (Denmark)

    Foglia, Aligi; Govoni, Laura; Gottardi, Guido;

    In this report a macro-element model for bucket foundations is formulated and validated against small-scale experimental results. The topics investigated are the response of the foundation under general monotonic loading and the long-term accumulated displacements under cyclic loading. The macro-...

  11. Physical Modelling of Bucket Foundation Under Long-Term Cyclic Lateral Loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

    2012-01-01

    functioning. In this article a 1g physical model of bucket foundation under horizontal and moment cyclic loading is described. A testing program including four tests was carried out. Every test was conducted for at least 30000 cycles, each with different loading features. The capability of the model...

  12. Plastic Jellyfish.

    Science.gov (United States)

    Moseley, Christine

    2000-01-01

    Presents an environmental science activity designed to enhance students' awareness of the hazards of plastic waste for wildlife in aquatic environments. Discusses how students can take steps to reduce the effects of plastic waste. (WRM)

  13. Ultraviolet-radiation-curable paints

    Energy Technology Data Exchange (ETDEWEB)

    Grosset, A M; Su, W F.A.; Vanderglas, E

    1981-09-30

    In product finishing lines, ultraviolet radiation curing of paints on prefabricated structures could be more energy efficient than curing by natural gas fired ovens, and could eliminate solvent emission. Diffuse ultraviolet light can cure paints on three dimensional metal parts. In the uv curing process, the spectral output of radiation sources must complement the absorption spectra of pigments and photoactive agents. Photosensitive compounds, such as thioxanthones, can photoinitiate unsaturated resins, such as acrylated polyurethanes, by a free radical mechanism. Newly developed cationic photoinitiators, such as sulfonium or iodonium salts (the so-called onium salts) of complex metal halide anions, can be used in polymerization of epoxy paints by ultraviolet light radiation. One-coat enamels, topcoats, and primers have been developed which can be photoinitiated to produce hard, adherent films. This process has been tested in a laboratory scale unit by spray coating these materials on three-dimensional objects and passing them through a tunnel containing uv lamps.

  14. SABRE: A Sensitive Attribute Bucketization and REdistribution framework for t-closeness

    KAUST Repository

    Cao, Jianneng

    2010-05-19

    Today, the publication of microdata poses a privacy threat: anonymous personal records can be re-identified using third data sources. Past research has tried to develop a concept of privacy guarantee that an anonymized data set should satisfy before publication, culminating in the notion of t-closeness. To satisfy t-closeness, the records in a data set need to be grouped into Equivalence Classes (ECs), such that each EC contains records of indistinguishable quasi-identifier values, and its local distribution of sensitive attribute (SA) values conforms to the global table distribution of SA values. However, despite this progress, previous research has not offered an anonymization algorithm tailored for t-closeness. In this paper, we cover this gap with SABRE, a SA Bucketization and REdistribution framework for t-closeness. SABRE first greedily partitions a table into buckets of similar SA values and then redistributes the tuples of each bucket into dynamically determined ECs. This approach is facilitated by a property of the Earth Mover\\'s Distance (EMD) that we employ as a measure of distribution closeness: If the tuples in an EC are picked proportionally to the sizes of the buckets they hail from, then the EMD of that EC is tightly upper-bounded using localized upper bounds derived for each bucket. We prove that if the t-closeness constraint is properly obeyed during partitioning, then it is obeyed by the derived ECs too. We develop two instantiations of SABRE and extend it to a streaming environment. Our extensive experimental evaluation demonstrates that SABRE achieves information quality superior to schemes that merely applied algorithms tailored for other models to t-closeness, and can be much faster as well. © 2010 Springer-Verlag.

  15. Bucket handle tears of the medial meniscus: meniscal intrusion rather than meniscal extrusion

    Energy Technology Data Exchange (ETDEWEB)

    Schlossberg, S. [Jacobi Medical Center, Department of Radiology, Bronx, NY (United States); Umans, H. [Jacobi Medical Center, Department of Radiology, Bronx, NY (United States); Jacobi Medical Center, Department of Surgery Division of Orthopedic Surgery, Bronx, NY (United States); Flusser, G. [Tel Aviv Sourasky Medical Center, Department of Radiology, Tel Aviv (Israel); DiFelice, G.S. [Jacobi Medical Center, Department of Surgery Division of Orthopedic Surgery, Bronx, NY (United States); Lerer, D.B. [Montefiore Medical Center, Department of Radiology, Bronx, NY (United States)

    2007-01-15

    To determine the frequency of medial meniscal extrusion (MME) versus ''medial meniscal intrusion'' in the setting of bucket handle tears. Images were evaluated for previously reported risk factors for MME, including: medial meniscal root tear, radial tear, degenerative joint disease and joint effusion. Forty-one consecutive cases of bucket handle tear of the medial meniscus were reviewed by consensus by two musculoskeletal radiologists. Imaging was performed using a 1.5 GE Signa MR unit. Patient age, gender, medial meniscal root integrity, MME, medial meniscal intrusion, degenerative joint disease, effusion and anterior cruciate ligament (ACL) tear were recorded. Thirteen females and 27 males (age 12-62 years, median=30 years) were affected; one had bucket handle tear of each knee. Effusion was small in 13, moderate in 9 and large in 18. Degenerative joint disease was mild in three, moderate in two and severe in one. 26 ACL tears included three partial and three chronic. Medial meniscal root tear was complete in one case and partial thickness in two. None of the 40 cases with an intact or partially torn medial meniscal root demonstrated MME. MME of 3.1 mm was seen in the only full-thickness medial meniscal root tear, along with chronic ACL tear, moderate degenerative joint disease and large effusion. Medial meniscal intrusion of the central bucket handle fragment into the intercondylar notch was present in all 41 cases. Given an intact medial meniscal root in the setting of a ''pure'' bucket handle tear, there is no MME. (orig.)

  16. The Swimming Pool (oil painting)

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Chen Xi was born in 1968 in Chongqing City, Sichuan Province. In 1991, she graduated with a Bachelor’s degree from the Oil Painting Department of the Central Academy of Fine Arts. Her paintings are soaked through with her mixed emotions towards urban life. The city, the concentrated mirror of human civilization, drives the human race further and further away from mother nature Molded ever more strictly by the socialization process, human beings live more and more like commodities. The ever-shrink-

  17. NGAWANG JIGME'S MODERN WASH PAINTINGS

    Institute of Scientific and Technical Information of China (English)

    KELZANG; DORJE

    2007-01-01

    Having received a thorough college education.Ngawang Jigme naturally expresses his academic knowledge and skills through his washing paintings.Though he grew up on the plateau cating Tsampa and yak flesh,drinking yak buttered tea,living in the clear atmosphere,sunny sky and mountain scenery,he would hardly be expected to tolerate the monotone world of wash painting,which adopts black and white as its principal theme and acknow ledges"blur impression"as the ultimate aim.He strives for total absorption int...

  18. The transdisciplinary potential of remediated painting

    DEFF Research Database (Denmark)

    Petersen, Anne Ring

    2011-01-01

    painting as a point of departure but moves beyond the limitations of dialogic intermedia into the field of transdisciplinary aesthetics. In support of my argument, I turn to the concept of remediation as it was first applied in new media theory by Jay David Bolter and Richard Grusin. The ambition...... and performance etc. This paper suggests that the transformation of the discipline of painting into an expanded field has not only liberated painting from its ties to its traditional repertoire of materials and modes of representation. It has also released a tremendous potential for image making that takes...... is to develop an apprehension of painting not as an artistic artifact or 'medium-specific' practice, but as a critical remediating process - painting as remediated painting. What could be gained from this reconceptualisation of the expanded field of painting? Firstly, it introduces an apprehension of painting...

  19. EVALUATION OF LOW-VOC LATEX PAINTS

    Science.gov (United States)

    The paper gives results of an evaluation of four commercially available low-VOC (volatile organic compound) latex paints as substitutes for conventional latex paints by assessing both their emission characteristics and their performance as coatings. Bulk analysis indicated that ...

  20. MR imaging of meniscal bucket-handle tears: a review of signs and their relation to arthroscopic classification

    Energy Technology Data Exchange (ETDEWEB)

    Aydingoez, Uestuen; Firat, Ahmet K. [Department of Radiology, Hacettepe University Medical Center, 06100 Ankara (Turkey); Atay, Ahmet Oe.; Doral, Nedim M. [Department of Orthopaedics and Traumatology, Hacettepe University Medical Center, 06100 Ankara (Turkey)

    2003-03-01

    Our objective was to review the MR imaging signs of meniscal bucket-handle tears and assess the relevance of these signs to the arthroscopic classification of displaced meniscal tears. Forty-five menisci in 42 patients who had a diagnosis of bucket-handle tear either on MR imaging or on subsequent arthroscopy (in which Dandy's classification of meniscal tears was used) were retrospectively analyzed for MR imaging findings of double posterior cruciate ligament (PCL), fragment within the intercondylar notch, absent bow tie, flipped meniscus, double-anterior horn, and disproportional posterior horn signs. Arthroscopy, which was considered as the gold standard, revealed 41 bucket-handle tears (either diagnosed or not diagnosed by MR imaging) in 38 patients (33 males, 5 females). There was a stastistically significant male preponderance for the occurrence of meniscal bucket-handle tears. Overall, sensitivity and positive predictive value of MR imaging for the detection of meniscal bucket-handle tears were calculated as 90%. Common MR imaging signs of meniscal bucket-handle tears in arthroscopically proven cases of such tears were the fragment in the notch and absent bow tie signs (98% frequency for each). Double-PCL, flipped meniscus, double-anterior horn, and disproportional posterior horn signs, however, were less common (32, 29, 29, and 27%, respectively). An arthroscopically proven bucket-handle tear was found in all patients who displayed at least three of the six MR imaging signs of meniscal bucket-handle tears. The presence of three or more MR imaging signs of meniscal bucket-handle tears is highly suggestive of this condition. (orig.)

  1. Mural Painting as Inclusive Art Learning Experience

    Science.gov (United States)

    Ho, Kong

    2010-01-01

    Traditional art education, like other academic disciplines, emphasizes competitiveness and individualism. Through a mural painting curriculum, learners participate in mural art and history appreciation, are active in mural theme or content construction, and engage in hands-on mural design and painting processes. When mural paintings are produced…

  2. Zinc, Paint loss and Harmony in blue

    DEFF Research Database (Denmark)

    Andersen, Cecil Krarup; Taube, Michelle; Vila, Anna

    2016-01-01

    P.S. Krøyer’s late and most popular paintings have proven very difficult to preserve, and as zinc white has been known to cause structural problems in paintings, the authors investigate if the damage seen in the late paintings can be related to the use of this relatively new pigment. Eight...

  3. Enhanced multifunctional paint for detection of radiation

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, Joseph C.; Moses, Edward Ira; Rubenchik, Alexander M.

    2017-03-07

    An enhanced multifunctional paint apparatus, systems, and methods for detecting radiation on a surface include providing scintillation particles; providing an enhance neutron absorptive material; providing a binder; combining the scintillation particles, the enhance neutron absorptive material, and the binder creating a multifunctional paint; applying the multifunctional paint to the surface; and monitoring the surface for detecting radiation.

  4. Stop and Paint the Flowers.

    Science.gov (United States)

    Phillips, Shelley

    2002-01-01

    Describes an art lesson where students used watercolors to paint a flower bouquet arranged in a vase. Explains that the students viewed examples of flower bouquets by artists such as Vincent van Gogh and Odilon Redon. Discusses, in detail, the process of creating the artworks. (CMK)

  5. Desalination of painted brick vaults

    DEFF Research Database (Denmark)

    Larsen, Poul Klenz

    The subject of the thesis is salt and moisture movement that causes damage to wall paintings on church vaults. The deterioration was studied in the churches of Fanefjord, Kirkerup and Brarup. A desalination method was tested om location. The salt and moisture transfer was examined in detail...

  6. The Painting on the Wall

    Directory of Open Access Journals (Sweden)

    Barbara Alfano

    2016-01-01

    Full Text Available This personal essay describes what influenced my development as a creative writer, in my childhood and adolescence. It delineates the effect on my imagination of family story-telling and of images—paintings and prints. I grew up in Italy, where I spent the first thirty years of my life.

  7. Microclimate boxes for panel paintings

    DEFF Research Database (Denmark)

    Wadum, Jørgen

    1998-01-01

    The use of microclimate boxes to protect vulnerable panel paintings is, therefore, not a new phenomenon of the past two or three decades. Rather, it has been a concern for conservators and curators to protect these objects of art at home and in transit since the end of the nineteenth century. The...

  8. Desalination of painted brick vaults

    DEFF Research Database (Denmark)

    Larsen, Poul Klenz

    The subject of the thesis is salt and moisture movement that causes damage to wall paintings on church vaults. The deterioration was studied in the churches of Fanefjord, Kirkerup and Brarup. A desalination method was tested om location. The salt and moisture transfer was examined in detail...

  9. Paint the World with Light

    Science.gov (United States)

    Gran, David

    2010-01-01

    Two classrooms on opposite sides of the world happened to be working on a very similar project at the same time. In both Shanghai, China, and Palm Springs, California, students were learning how to turn their flashlights and other light-emitting objects into paintbrushes. Light painting is a form of long-exposure photography in which the shutter…

  10. THE DEVELOPMENT AND TESTING OF A POLYSENSORY INSTRUCTIONAL SYSTEM FOR TEACHING KNOWLEDGES AND SKILLS ASSOCIATED WITH THE USE OF EXPANDABLE POLYSTYRENE PLASTICS. REPORT NO. 18.

    Science.gov (United States)

    NISH, DALE LEROY

    THIRTY STUDENTS IN GRADES 6 THROUGH 12 CLASSIFIED INTO HIGH, AVERAGE, AND LOW ABILITY GROUPS, USED EXPANDABLE POLYSTYRENE PLASTICS AND EQUIPMENT TO CONSTRUCT A FOAMED RUBBER ICE BUCKET TO PROVIDE AN INDICATOR OF THE SUCCESS OF THE POLYSENSORY SELF-INSTRUCTIONAL SYSTEM DEVELOPED FOR THIS EXPERIMENT. A PRETEST DETERMINED EXISTING KNOWLEDGES AND…

  11. But when was it painted?

    Science.gov (United States)

    Lundstad, E.; Woll, G.

    2009-04-01

    The Munch Museum, Oslo, Norway, is dedicated to the visual works of the famous Norwegian painter Edvard Munch (1863 - 1944). Edvard Munch was a symbolist, expressionist painter and printmaker from Oslo, Norway. He was regarded as the pioneer of the amazing Expressionist movement. His art work from the late 1800's is the most well known, but his later work is gradually attracting more attention and is quite an inspiration of many of today's artists. The Munch Museum catalogue for 2008 contains about 1700 paintings of which virtually very few have a precise date. Even when the artist has written the year on the painting itself, there may be a significant uncertainty about this date, and partly due to unclear writing making it difficult to interpret the numbers. This means that other sources need to be applied to verify an accurate date. The climatologist at the Norwegian Meteorological Institute can help dating paintings of Munch. E. g. the painting "Standing Woman with Arms Folded". The painting shows a woman in front of a hill with much snow. The location is almost certainty Grimsrød on Jeløya, a property Munch began renting on March 1, 1913. Jeløya is an island at the southeastcoast of Norway near the town Moss. Jeløya has usually not so much snow because it is near by the sea and windy. The last digit in the date is unclear and has been read as both '3' and '5'. The woman in the portrait, Ingeborg Kaurin, was Munch's model up to the beginning of 1915, so both dates are possible. The year written on the painting has been read as both 1913 and 1915, and since 1974 it has usually been interpreted as 1913 (Stenersensamlingen's catalogue 1974). In the project "But when was it painted?" disclose that it could be another year. One way to reconsider when a painting was painted is to study geophysical characteristics and consider historical observations of snow. The method that is used here is to study daily meteorological snow data from this period from the

  12. Order-fractal transitions in abstract paintings

    Energy Technology Data Exchange (ETDEWEB)

    Calleja, E.M. de la, E-mail: elsama79@gmail.com [Instituto de Física, Universidade Federal do Rio Grande do Sul, Caixa Postal 15051, 91501-970, Porto Alegre, RS (Brazil); Cervantes, F. [Department of Applied Physics, CINVESTAV-IPN, Carr. Antigua a Progreso km.6, Cordemex, C.P.97310, Mérida, Yucatán (Mexico); Calleja, J. de la [Department of Informatics, Universidad Politécnica de Puebla, 72640 (Mexico)

    2016-08-15

    In this study, we determined the degree of order for 22 Jackson Pollock paintings using the Hausdorff–Besicovitch fractal dimension. Based on the maximum value of each multi-fractal spectrum, the artworks were classified according to the year in which they were painted. It has been reported that Pollock’s paintings are fractal and that this feature was more evident in his later works. However, our results show that the fractal dimension of these paintings ranges among values close to two. We characterize this behavior as a fractal-order transition. Based on the study of disorder-order transition in physical systems, we interpreted the fractal-order transition via the dark paint strokes in Pollock’s paintings as structured lines that follow a power law measured by the fractal dimension. We determined self-similarity in specific paintings, thereby demonstrating an important dependence on the scale of observations. We also characterized the fractal spectrum for the painting entitled Teri’s Find. We obtained similar spectra for Teri’s Find and Number 5, thereby suggesting that the fractal dimension cannot be rejected completely as a quantitative parameter for authenticating these artworks. -- Highlights: •We determined the degree of order in Jackson Pollock paintings using the Hausdorff–Besicovitch dimension. •We detected a fractal-order transition from Pollock’s paintings between 1947 and 1951. •We suggest that Jackson Pollock could have painted Teri’s Find.

  13. Self-Reduction of Displaced Bucket-Handle Medial Meniscal Tear in a 71-Year-Old Patient

    OpenAIRE

    2015-01-01

    Background: Bucket-handle meniscal tears are rare in geriatric patients. Displaced bucket-handle meniscal tears are usually treated operatively. Due to the rarity of these tears in elderly patients and conflicting evidence regarding the use of arthroscopy versus conservative treatment, it is valuable to report the clinical presentation, treatment, and outcome of these injuries in elderly patients. Case Description: We describe a 71-year-old man who presented with an acute, displaced, magnetic...

  14. Numerical Study of Piping Limits for Installation of Large Diameter Buckets in Layered Sand

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Thilsted, C.L.

    2010-01-01

    The bucket foundations, often referred as ‘suction caissons’, are large cylindrical structures, typically made in steel. The bucket foundations have the potential to be the cost-effective option for offshore wind turbines, if suction assisted penetration is employed. Suction installation may cause...... formation of piping channels, which break down the hydraulic seal and prevent further installation. This paper presents a numerical study of failure limits during suction installation in respect to both homogenous and layered soil profile. A numerical flow analysis is performed to determine the hydraulic...... gradients developing in response to applied suction and the results are presented as simple closed form solutions useful for evaluation of suction thresholds against piping. These close form solutions are compared with large scale model test, performed in a natural seabed at a test site in Frederikshavn...

  15. Design of Transition Pieces for Bucket Foundations for Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia

    Using bucket foundations for offshore wind turbines is an alternative solution to monopiles and other foundation types installed in shallow and transitional water depths (up to 50−60 m) due to its greater stiffness, fair simplicity and high speed of installation. However, as only a few prototypes...... with the suction bucket used as a monopod foundation for an offshore wind turbine. Traditionally, this part is made of steel triangular flange-reinforced shear panels (stiffeners) which require expensive production, corrosion protection, and suffer from fatigue at the welded joints due to cyclic loading produced...... by the combined action of wind and waves. The aim of the project was to find an alternative design of this TP utilizing FEA and an alternative material called Compact Reinforced Composite (CRC®), or “The New Concrete”, invented at Aalborg Portland A/S in 1986, which is an Ultra-High-Performance Fibre...

  16. Numerical Study of Piping Limits for Installation of Large Diameter Buckets in Layered Sand

    DEFF Research Database (Denmark)

    Ibsen, Lars Bo; Thilsted, C.L.

    2010-01-01

    The bucket foundations, often referred as ‘suction caissons’, are large cylindrical structures, typically made in steel. The bucket foundations have the potential to be the cost-effective option for offshore wind turbines, if suction assisted penetration is employed. Suction installation may cause...... formation of piping channels, which break down the hydraulic seal and prevent further installation. This paper presents a numerical study of failure limits during suction installation in respect to both homogenous and layered soil profile. A numerical flow analysis is performed to determine the hydraulic...... gradients developing in response to applied suction and the results are presented as simple closed form solutions useful for evaluation of suction thresholds against piping. These close form solutions are compared with large scale model test, performed in a natural seabed at a test site in Frederikshavn...

  17. Simultaneous bicompartmental bucket-handle meniscal tears with intact anterior cruciate ligament: a case report

    Directory of Open Access Journals (Sweden)

    Beris Alexandros E

    2010-02-01

    Full Text Available Abstract Introduction Bucket handle tear of the menisci is a common type of lesion resulting from injury to the knee joint. Bucket handle injury of both menisci in almost all cases is associated with a lesion to either the anterior or the posterior cruciate ligament of the knee joint. We describe a case of acute bucket-handle tear of the medial and lateral menisci with intact anterior and posterior cruciate ligaments in a dancer. To the best of our knowledge, there are no previous reports of this type of injury in the literature. Case presentation A 28-year-old Caucasian Greek woman presented to the emergency department after sustaining an injury to her right knee during dancing. An MRI evaluation demonstrated tears in both menisci of the right knee, while the anterior and posterior cruciate ligaments were found to be intact. A partial medial and lateral meniscectomy was then performed. At a follow-up examination six months after her injury, clinical tests demonstrated that our patient's right knee was stable, had a full range of motion and had no tenderness. She was satisfied with the outcome of the operation and returned to her pre-injury activities. Conclusion We present the first case in the literature that describes a combined bucket-handle injury of both the medial and lateral menisci with an intact anterior cruciate ligament. The clinical examination of the anterior cruciate ligament was unremarkable, with no signs of deficiency or rupture. The posterior cruciate ligament was also intact. On magnetic resonance imaging, the ligaments were visualised as intact in all their length. These findings were confirmed by arthroscopic evaluation.

  18. Structural Optimization of an Offshore Wind Turbines Transition Pieces for Bucket Foundations

    OpenAIRE

    Nezhentseva, Anastasia; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo; Sørensen, Eigil V.

    2011-01-01

    Traditionally, offshore constructions are made of steel. The focus of this paper is optimization of a transition piece (TP) connecting the offshore wind turbine column with a suction bucket foundation. Suction caissons, typically used for shallow water depths, have been proved to be adequate in residual soil conditions for depths up to approximately 40 m. The existing design practice is limited to the use of steel-flange-reinforced shear panels. Desirable outcome is proposal of an alternative...

  19. Small-Scale Testing of Laterally Loaded Bucket Foundations in Dense Sand

    OpenAIRE

    Ibsen, Lars Bo; Foglia, Aligi

    2011-01-01

    Monopod bucket foundations promise to become a reliable and cost-effective concept for offshore wind turbine. Physical models are essential to understand the behavior of soil-structure systems. When conducting small-scale experiments on soil, scale effects can considerably affect the tests outcome. In a bid for overcoming this issue, a novel testing system based on the application of suction between the soil surface and a membrane is employed. The comparison between the tests conducted at str...

  20. The Bucket System – A computer mediated signaling system for group improvisation

    DEFF Research Database (Denmark)

    Dahlstedt, Palle; Nilsson, Per Anders; Robair, Gino

    2015-01-01

    The Bucket System is a new system for computer-mediated ensemble improvisation, designed by improvisers for improvisers. Coming from a tradition of structured free ensemble improvisation practices (comprovisation), influenced by post-WW2 experimental music practices, it is a signaling system...... implemented with a set of McMillen QuNeo controllers as input and output interfaces, powered by custom software. It allows for a new kind of on-stage compositional/improvisation interaction....

  1. Investigations on macro-element modelling of bucket foundations for offshore wind turbines

    OpenAIRE

    Foglia, Aligi; Govoni, Laura; Gottardi, Guido; Ibsen, Lars Bo

    2014-01-01

    In this report a macro-element model for bucket foundations is formulated and validated against small-scale experimental results. The topics investigated are the response of the foundation under general monotonic loading and the long-term accumulated displacements under cyclic loading. The macro-model for shallow foundations proposed by Nova and Montrasio (1991) is modified to comply with the response of skirted foundations for offshore wind turbines under general loading. On the base of di P...

  2. Experimental damping assessment of a full scale offshore mono bucket foundation

    DEFF Research Database (Denmark)

    Gres, Szymon; Fejerskov, Morten; Ibsen, Lars Bo;

    2016-01-01

    This paper quantifies the system damping of a offshore meteorological mast supported by a Mono Bucket foundation based on a long-term experimental campaign. The structure is located at Dogger Bank west, North Sea, and equipped with a measurement system monitoring acceleration, strain, inclination...... shows that the total damping ratio of the lowest eigenmode is normally distributed with mean value of 1.11% of critical damping. Linear correlation between the damping ratio and the significant wave height is observed....

  3. The Bucket System – A computer mediated signaling system for group improvisation

    DEFF Research Database (Denmark)

    Dahlstedt, Palle; Nilsson, Per Anders; Robair, Gino

    2015-01-01

    The Bucket System is a new system for computer-mediated ensemble improvisation, designed by improvisers for improvisers. Coming from a tradition of structured free ensemble improvisation practices (comprovisation), influenced by post-WW2 experimental music practices, it is a signaling system...... implemented with a set of McMillen QuNeo controllers as input and output interfaces, powered by custom software. It allows for a new kind of on-stage compositional/improvisation interaction....

  4. Performance of Combined Water Turbine Darrieus-Savonius with Two Stage Savonius Buckets and Single Deflector

    OpenAIRE

    Sahim, Kaprawi; Santoso, Dyos; Sipahutar, Riman

    2016-01-01

    The objective of this study is to show the effect of single deflector plate on the performance of combined Darrieus-Savonius water turbine. In order to overcome the disadvantages of low torque of solo Darrieus turbine, a plate deflector mounted in front of returning Savonius bucket of combined water turbine composing of Darrieus and Savonius rotor has been proposed in this study. Some configurations of combined turbines with two stage Savonius rotors were experimentally tested in a river of c...

  5. Subjective visual vertical with the bucket method in Brazilian healthy individuals.

    Science.gov (United States)

    Ferreira, Maristela Mian; Cunha, Fabiana; Ganança, Cristina Freitas; Ganança, Maurício Malavasi; Caovilla, Heloisa Helena

    2016-01-01

    The capacity of a healthy individual to estimate the true vertical in relation to the Earth when a fluorescent line is aligned in a completely dark room is called the subjective visual vertical. To evaluate subjective visual vertical using the bucket method in healthy Brazilian individuals. Binocular subjective visual vertical was measured in 100 healthy volunteers, 50 females and 50 males. The volunteers indicated the estimated position in which a fluorescent line inside a bucket reached the vertical position. A total of ten repetitions were performed, five clockwise and five counterclockwise. Data were tabulated and analyzed statistically. It was observed that the highest concentration of absolute values of vertical deviation was present up to 3°, regardless of gender, and the vertical deviation did not increase with age. The analysis of the mean of the absolute values of deviations from the vertical of 90% of the sample showed a maximum value of 2.6°, and at the analysis of 95%, the maximum value was 3.4° deviation from the vertical. The bucket method is easy to perform and interpret when assessing the deviation of the subjective visual vertical in relation to the true vertical in healthy Brazilian individuals. Copyright © 2016 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

  6. A Bibliometric Assessment of Global Ice Bucket Challenge (Amyotrophic Lateral Sclerosis) Research.

    Science.gov (United States)

    Ram, Shri

    2016-10-01

    This study is a quantitative and qualitative assessment of the global research trends on amyotrophic lateral sclerosis (ALS) (popularly known as Ice Bucket Challenge), through related literatures retrieved from SCOPUS multidisciplinary database for the period 1974-2013. This study is aimed at analyzing the literature on ALS in terms of document type, language, annual growth, productive country, journal, authors, subject, and most cited articles. The bibliographic data for this study was retrieved from the SCOPUS database using keywords 'amyotrophic lateral sclerosis', 'motor neurone disease', 'Charcot disease', 'Lou Gehrig's disease', 'Ice Bucket Challenge' available in title, abstract, and keyword fields of Scopus database from 1974 to 2013. The literature analysis included 21,750 articles during the period from 1974 to 2013 in different areas of ALS. USA was the most productive country in terms of literature produced, while Neurology was the most productive journal. An intensive awareness created by 'Ice Bucket Challenge' has attracted masses, and an intensive growth of literature is pertinent on ALS. The results of this study are expressed in terms of growth of literature, output of individual countries, and authors, and will be helpful in collaborative research in future.

  7. Numerical analysis of non-stationary free surface flow in a Pelton bucket

    Energy Technology Data Exchange (ETDEWEB)

    Hana, Morten

    1999-07-01

    Computation and analysis of flow in Pelton buckets have been carried out. First a graphical method is investigated and partially improved. In order to decide whether to improve the method further or disregard it in favour of commercial computational fluid dynamics (CFD) codes, a study on numerical methods for free surface flow was carried out. This part of this work concentrates on the theoretical background for different numerical methods, and describes some practical considerations. Although small programs were created based on the literature survey, but only one reported herein, it was soon found that commonly available numerical codes were favourable in use. A code, RIPPLE, was acquired to study the Volume of Fluid (VOF) method in detail. The commercial codes used were Flow-3D and CFX-4. These programs were used in three different cases. First, a simplified 2-dimensional case was verified experimentally. Next, a 3-dimensional fixed jet calculation was carried out. Finally, numerical calculations with relative motion between the jet and buckets were carried out with CFX-4. The conclusion is that commercial CFD codes can replace the graphical method. But careful implementation is needed in order to resolve the special features of Pelton turbines, which are the free surface, the complex geometry and the relative motion between the jet and the bucket.

  8. Design and Development of Electro-Mechanical Twins Tipping Buckets Runoff-Meter

    Directory of Open Access Journals (Sweden)

    Olotu Yahaya

    2014-07-01

    Full Text Available Electro-mechanical tipping bucket runoff-meter was designed and developed to measure surface runoff water using locally-sourced components. The instrument consists of metallic-fabricated runoff plot area of 2 m 2 , depth 0.25 m and metal gauge of 3mm. The tipping operation was initiated by arranging the sensitive electro-mechanical components such digital micro-switch (SW1,SW2, SW3 and SW4, pair of open/close circuit breakers (No,Nc, electronic speed gear and circular rotating disc to a pair of twins buckets of runoff volume 0.141 liter capacity per bucket which corresponds to 0.25 mm runoff depth. The whole arrangement was powered by a 12V by 75 AH battery and the tipping processes was being recorded by the electro-mechanical data logger. The instrument has a measuring accuracy of ±0.001 liter per tip. It was calibrated to measure minimum and maximum runoff volume from 0.14l to 200 liters, these values correspond to 0.25 mm and 800 mm runoff depths respectively. Therefore, precise results obtained using the instrument could be used to establish strong database for measuring and storing accurate surface runoff data which in turn could be applied for hydrological modeling for sustainable water resources management and design of hydraulic structures

  9. RED- DTB:A Dual Token Bucket Based Queue Management Algorithm

    Institute of Scientific and Technical Information of China (English)

    Yin Jian-hua; Cao Yang; Ling Jun; Huang Tian-xi

    2003-01-01

    Improving the Quality of Service (QoS) of Internet traffic is wide-ly recognized as a critical issue for the next-generation networks. In this paper,we present a new algorithm for the active queue management, namely RED-DTB. This buffer control technique is used to enforce approximate fairness among a large number of concurrent Internet flows. Like RED (Random Early Detection) algorithm, the RED-DTB mechanism can be deployed to actively re-spond to the gateway congestion, keep the gateway in a healthy state, and pro-tect the fragile flows from being stolen band width by greedy ones. The algo-rithm is based on the so-called Dual Token Bucket (DTB) pattern. That is, onthe one hand, every flow is rate-limited by its own token bucket, to ensure thatit can not consume more than its fair share of bandwidth; On the other hand,to make some compensations to less aggressive flows, such as connections with larger round trip time or smaller sending window, and to gain a relatively high-er system utilization coefficient, all flows, depending on their individual behav-ior, may have a chance to fetch tokens from the public token bucket when theyrun out of their own share of tokens. The algorithm is analyzed and evaluatedby simulations, and is proved to be effective in protecting the gateway bufferand controlling the fair allocation of bandwidth among flows.

  10. RED-DTB: A Dual Token Bucket Based Queue Management Algorithm

    Institute of Scientific and Technical Information of China (English)

    YinJian-hua; CaoYang; LingJun; HuangTian-xi

    2003-01-01

    Improving the Quality of Service (QoS) of Internet traffic is widely recognized as a critical issue for the next-generation networks. In this paper,we present a new algorithm for the active queue management, namely RED-DTB. This buffer control technique is used to enforce approximate fairness among a large number of concurrent Internet flows. Like RED (Random Early Detection) algorithm, the RED-DTB mechanism can be deployed to actively respond to the gateway congestion, keep the gateway in a healthy state, and protect the fragile flows from being stolen bandwidth by greedy ones. The algorithm is based on the so-called Dual Token Bucket (DTB) pattern. That is, on the one hand, every flow is rate-limited by its own token bucket, to ensure that it can not consume more than its fair share of bandwidth; On the other hand,to make some compensations to less aggressive flows, such as connections with larger round trip time or smaller sending window, and to gain a relatively higher system utilization coefficient, all flows, depending on their individual behavior, may have a chance to fetch tokens from the public token bucket when they run out of their own share of tokens. The algorithm is analyzed and evaluated by simulations, and is proved to be effective in protecting the gateway buffer and controlling the fair allocation of bandwidth among flows.

  11. Erosion of Pelton buckets and changes in turbine efficiency measured in the HPP Fieschertal

    Science.gov (United States)

    Abgottspon, A.; Staubli, T.; Felix, D.

    2016-11-01

    Geometrical changes and material loss of Pelton turbine runners as well as changes in turbine efficiency were measured at HPP Fieschertal in Valais, Switzerland. The HPP is equipped with two horizontal axis Pelton units, with each 32 MW nominal power, 7.5 m3/s design discharge, 515 m head and two injectors. The injectors and the buckets are hard-coated. Hydro-abrasive erosion was quantified based on repeated measurements on two runner buckets using (i) 3d-scanning and (ii) a coating thickness gauge. Changes in efficiency were measured by applying the sliding needle procedure. In addition to these periodically performed measurements, efficiency was also continuously monitored. The highest erosion rate was measured during the first half of the sediment season 2012 including a major sediment transport event. Because the runner was not fully reconditioned at the beginning of this season, progressive damages occurred. After the event, a splitter width of 10 mm was measured, corresponding to 1.5 % of the inner bucket width. The cut-outs were eroded by up to 9 mm towards the axis. The efficiency reductions ranged from 1 % in the year with the major sediment transport event to insignificant differences in 2014, when the sediment load was small and only little hydro-abrasive erosion occurred.

  12. PCBs in Caulk and Paint

    Science.gov (United States)

    2010-06-16

    4 ~~ I Qi I "!~~~ ~~4 4.00 r· 1 - -OSA (85 %) 7.11 3.27 Raw linseed oil 6.40 Linseed oil , heat-bodied, viscosity Z3 6.40 Titanium dioxide 15.20...Potential PCB sources  Any of these products if manufactured before 1979: ►Capacitors or transformers ►Mineral- oil filled electrical equipment...rubber parts ► Applied dried paints ► Oil -based paints ► Coatings/Sealants ► Caulking ► Adhesives and tapes ► Carbonless copy paper ► Galbestos ► Sound

  13. Paint or color? Bursa example

    Science.gov (United States)

    Habib, Susan; Cetinturk, Nihal

    2002-06-01

    While traditional/vernacular color scheme of a city in historical regions should be protected, changes in life style reflect on cityscapes in all ways, in which the role of new materials, paints, etc. cannot be denied. Lack of architectural and urban design studies in this field added to existing countless opportunities of new technology, with the strong desire to trying those by building owners, users and contractors have caused a chaotic situation in the use of color in cities; Bursa with its historical colorful background is no exception. All these form a trial and error phase, with painted or materials applied on surfaces without a sensitive touch to transform them to color. This must be taken in mind that color with its inherent power can bind past, present and future of the city and create an urban sense of place.

  14. Microclimate boxes for panel paintings

    DEFF Research Database (Denmark)

    Wadum, Jørgen

    1998-01-01

    The use of microclimate boxes to protect vulnerable panel paintings is, therefore, not a new phenomenon of the past two or three decades. Rather, it has been a concern for conservators and curators to protect these objects of art at home and in transit since the end of the nineteenth century....... The increased number of travelling exhibitions in recent years has heightened the need to protect paintings during circulation (Thomson 1961; Mecklenburg 1991). The use and design of microclimate boxes have been evolving since 1892. These boxes may be divided into three broad groups: those using an active...... buffer material to stabilize the internal RH, a more recent box containing no added buffer material, and, in recent times, boxes with an altered gas content. Another concern is the appearance (aesthetics) of the box....

  15. Washi Painting Exchanges Promote Friendship

    Institute of Scientific and Technical Information of China (English)

    Chuan; You

    2014-01-01

    <正>Invited by the Sichuan Provincial People’s Association for Friendship with Foreign Countries(SIFA),a washi painting exchange delegation headed by Umeko Iwai,President of Rainbow Society of Japan,a Hiroshima-based non-profit organization,visited Sichuan Province from November 3 to 5,2013.Rice paper was invented in China in ancient times.When the paper-making

  16. Color signatures in Amorsolo paintings

    Science.gov (United States)

    Soriano, Maricor N.; Palomero, Cherry May; Cruz, Larry; Yambao, Clod Marlan Krister; Dado, Julie Mae; Salvador-Campaner, Janice May

    2010-02-01

    We present the results of a two-year project aimed at capturing quantifiable color signatures of oil paintings of Fernando Amorsolo, the Philippine's first National Artists. Color signatures are found by comparing CIE xy measurements of skin color in portraits and ground, sky and foliage in landscapes. The results are compared with results of visual examination and art historical data as well as works done by Amorsolo's contemporaries and mentors.

  17. Plastics Technology.

    Science.gov (United States)

    Barker, Tommy G.

    This curriculum guide is designed to assist junior high schools industrial arts teachers in planning new courses and revising existing courses in plastics technology. Addressed in the individual units of the guide are the following topics: introduction to production technology; history and development of plastics; safety; youth leadership,…

  18. The use of knowledge-based Genetic Algorithm for starting time optimisation in a lot-bucket MRP

    Science.gov (United States)

    Ridwan, Muhammad; Purnomo, Andi

    2016-01-01

    In production planning, Material Requirement Planning (MRP) is usually developed based on time-bucket system, a period in the MRP is representing the time and usually weekly. MRP has been successfully implemented in Make To Stock (MTS) manufacturing, where production activity must be started before customer demand is received. However, to be implemented successfully in Make To Order (MTO) manufacturing, a modification is required on the conventional MRP in order to make it in line with the real situation. In MTO manufacturing, delivery schedule to the customers is defined strictly and must be fulfilled in order to increase customer satisfaction. On the other hand, company prefers to keep constant number of workers, hence production lot size should be constant as well. Since a bucket in conventional MRP system is representing time and usually weekly, hence, strict delivery schedule could not be accommodated. Fortunately, there is a modified time-bucket MRP system, called as lot-bucket MRP system that proposed by Casimir in 1999. In the lot-bucket MRP system, a bucket is representing a lot, and the lot size is preferably constant. The time to finish every lot could be varying depends on due date of lot. Starting time of a lot must be determined so that every lot has reasonable production time. So far there is no formal method to determine optimum starting time in the lot-bucket MRP system. Trial and error process usually used for it but some time, it causes several lots have very short production time and the lot-bucket MRP would be infeasible to be executed. This paper presents the use of Genetic Algorithm (GA) for optimisation of starting time in a lot-bucket MRP system. Even though GA is well known as powerful searching algorithm, however, improvement is still required in order to increase possibility of GA in finding optimum solution in shorter time. A knowledge-based system has been embedded in the proposed GA as the improvement effort, and it is proven that the

  19. Paint chip poisoning of Laysan albatross at Midway Atoll (Pacific Ocean)

    Science.gov (United States)

    Sileo, L.; Fefer, S.I.

    1987-01-01

    Epizootic mortality occurred in Laysan albatross (Diomedea immutabilis) fledgings at Midway Atoll in 1983. Heavy metal toxicity from ingestion of weathered paint chips was one of the causes. Sick albatrosses were unable to retract their wings, causing a 'droop-wing' appearance. Five normal and 12 droop-winged fledglings were captured, killed, and examined. Paint chips found in the proventriculus of the affected fledglings contained up to 144,000 ppm lead. Blood, liver, and kidney concentrations of lead in affected birds were higher than in normal fledglings, and acid-fast intranuclear inclusion bodies were present in the kidneys. Degenerative lesions were present in the myelin of some brachial nerves. Weathered paint samples collected from 12 buildings contained up to 247,250 ppm lead and 101 ppm mercury. Lead poisoning was diagnosed in 10 of the droop-winged albatrosses and was one of the causes of morbidity. Mercury toxicosis and plastic impaction were other possible causes.

  20. Copper Based Antifouling Paints for Prevention of Marine Growth on ship Hulls

    Directory of Open Access Journals (Sweden)

    Y.P.S. Nirvan

    1982-01-01

    Full Text Available "The mode of action and requirements of ingredients of copper based antifouling paints used in the country for the prevention of fouling, on ship-hulls have been described. The studies on performance of antifouling paints based on cuprous oxide-chlorinated rubber-rosin system have also been reported. Antifouling life improves with increase in concentration of cuprous oxide, 43 per cent by volume being the optimum toxic content. A minimum rosin to resin ratio of 3:1 is required to permit adequate release of copper for prolonged periods. Hydrolysable plasticizer namely tricresyl phosphate has been found to be superior to chlorinated paraffin wax for the design of antifouling compositions. The antifouling paint based on chlorinated rubber resin is expected to give a life of 15-18 months in service."

  1. Conservation problems with paintings containing fluorescent layers of paint

    Directory of Open Access Journals (Sweden)

    Stefanie De Winter

    2010-11-01

    Full Text Available L’artiste moderne cherche continuellement de nouvelles techniques. Des nouveaux matériaux tels que l’éponge, le polyester, le sable, etc. sont devenus courants. Ces développements amènent de nouveaux problèmes dans le domaine de la conservation (préventive des matériaux en question. Chaque matériau doit être analysé individuellement afin de préserver  le mieux possible l’intention de l’artiste à long terme. La présente recherche concerne des matériaux très récents: les pigments et les couleurs fluorescentes. Ces derniers n’ont fait leur apparition qu’au vingtième siècle. Pour cette raison les données concernant leur dégradation et leur conservation sont peu nombreuses. La majorité des tableaux fluorescents sont conçus pour être montrés sous éclairage UV. En cas de dommage, si l’œuvre a besoin d’être retouchée, ceci pose un grand problème esthétique. La retouche devient visible sous les lampes UV. La première partie de la recherche concerne la composition des différentes sortes de pigments et de peintures. Par la suite, les différentes causes de dégradation- lumière UV, chaleur, etc.- sont analysées en détail. Pour conclure, un possible remède est proposé.In modern art we can see that artists are breaking with traditional techniques. New materials like sponge, polyester, sand, etc. are being used. This causes a lot of new problems in the (preventive conservation of works containing these materials. Every material needs to be researched individually so the exact intention of the artist can be preserved for a (relatively long period. My research is about very recent materials: fluorescent pigments and paints. These only started to be used by artists from the 60’s. That's why there is not much information about their aging and ways to (preventively conserve them. A lot of fluorescent paintings are meant to be shown under UV-light. If a fluorescent painting has damage and needs to be retouched

  2. Assessment of potential plastic-degrading fungi in Jordanian habitats

    OpenAIRE

    IBRAHIM, Ibrahim N.; MARAQA, Anwar; Hameed, Khalid M.

    2011-01-01

    Out of 70 fungal isolates recovered from soil, wall paints (Latex), and pieces of plastic debris from different habitats in Jordan and plastic shields of street light posts on campus, 35 isolates showed varied potential to degrade polyester-polyurethane (PS-PUR). Six of these isolates (Fusarium solani, Alternaria solani, Spicaria spp., Aspergillus fumigatus, Aspergillus terreus, and Aspergillus flavus) were selected on the basis of their growth rates on basal salt media amended with PS-PUR as...

  3. Ernst H. Gombrich on Abstract Painting

    OpenAIRE

    Elisa Caldarola

    2015-01-01

    Ernst H. Gombrich criticized abstract painting with several remarks scattered around his wide oeuvre. I argue that his view of abstract paintings is coherent with the account of pictorial representation he put forward in Art and Illusion, show some limits of such view, and maintain that, although several of Gombrich’s criticisms of abstract painting should be rejected, some of his remarks are insightful and worth of consideration.

  4. Ernst H. Gombrich on Abstract Painting

    Directory of Open Access Journals (Sweden)

    Elisa Caldarola

    2015-11-01

    Full Text Available Ernst H. Gombrich criticized abstract painting with several remarks scattered around his wide oeuvre. I argue that his view of abstract paintings is coherent with the account of pictorial representation he put forward in Art and Illusion, show some limits of such view, and maintain that, although several of Gombrich’s criticisms of abstract painting should be rejected, some of his remarks are insightful and worth of consideration.

  5. The magnetic imaging of oil paintings

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, P Costa [Department of Physics, PUC-Rio, R. Marques de Sao Vicente 225, 22453-900 Rio de Janeiro, RJ (Brazil); Barros, H Lins de [CBPF, R. Xavier Sigaud 150, 22290-180 Rio de Janeiro, RJ (Brazil); Portinari, J C [Projeto Portinari, PUC-Rio, R. Marques de Sao Vicente 225, 22453-900 Rio de Janeiro, RJ (Brazil); Wolff, C S [Department of Physics, PUC-Rio, R. Marques de Sao Vicente 225, 22453-900 Rio de Janeiro, RJ (Brazil); Kafensztok, S M [Department of Physics, PUC-Rio, R. Marques de Sao Vicente 225, 22453-900 Rio de Janeiro, RJ (Brazil); Carvalho, H R [Department of Physics, PUC-Rio, R. Marques de Sao Vicente 225, 22453-900 Rio de Janeiro, RJ (Brazil); Acosta-Avalos, D [IP and D-UNIVAP, Av. Shihima Hifumi 2911, 12244-000 Sao Jose dos Campos, SP (Brazil); Symko, O G [Department of Physics, University of Utah, 84112 UT (United States); Bruno, A C [Department of Physics, PUC-Rio, R. Marques de Sao Vicente 225, 22453-900 Rio de Janeiro, RJ (Brazil)

    2004-06-01

    We propose a new technique for authentication of oil paintings, using a scanning SQUID technique to measure its magnetic field. The paintings are pre-magnetized in an homogeneous field of 100 G. It was observed that the response depends on the ferromagnetic properties of each paint independent of its colour. This shows that a magnetic image could be used as a magnetic signature for authentication purposes. (rapid communication)

  6. The Transdisciplinary Potential of Remediated Painting

    DEFF Research Database (Denmark)

    Petersen, Anne Ring

    2010-01-01

    the limitations of dialogic intermedia into the field of transdisciplinary aesthetics. In support of my argument, I turn to the concept of remediation as it was first applied in new media theory by Jay David Bolter and Richard Grusin. The ambition is to develop an apprehension of painting not as an artistic...... that the transformation of the discipline of painting into an expanded field has not only liberated painting from its ties to its traditional repertoire of materials and modes of representation. It has also released a tremendous potential for image making that takes painting as a point of departure but moves beyond...

  7. Three-dimensional survey of paint layer

    Science.gov (United States)

    Pampaloni, Enrico; Bellucci, Roberto; Carcagni, Pierluigi; Casaccia, Antonella; Fontana, Raffaella; Gambino, Maria Chiara; Piccolo, Roberta; Pingi, Paolo; Pezzati, Luca

    2007-07-01

    The quantitative morphological analysis of a painting surface allows to evidence form defects and to study, thus, their influence on the stability of the paint and preparatory layers, as well as of the support. Therefore a three-dimensional survey can be very useful in planning the restoration intervention of a painting. In this work we present the results of the surface analysis carried out on the painting "Ultima Cena" by Giorgio Vasari. This panel painting is severely affected by paint film wrinkling produced as a consequence of the flood that occurred in Florence in 1966. Our analysis, accomplished to quantify the lengthening of the paint layer with respect to the one of the support in order to plan the restoration intervention, was performed on 25 profiles separated each by 10 cm in order to cover the whole painting surface. A data analysis, based on morphological filtering named "Rolling Ball" transformation, was used to evaluate the length difference between the paint layer and the panel support along each profile.

  8. Order-Fractal transition in abstract paintings

    OpenAIRE

    De la Calleja, E. M.; Cervantes, F.; De la Calleja, J.

    2015-01-01

    We report the degree of order of twenty-two Jackson Pollock's paintings using \\emph{Hausdorff-Besicovitch fractal dimension}. Through the maximum value of each multi-fractal spectrum, the artworks are classify by the year in which they were painted. It has been reported that Pollock's paintings are fractal and it increased on his latest works. However our results show that fractal dimension of the paintings are on a range of fractal dimension with values close to two. We identify this behavio...

  9. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Science.gov (United States)

    2010-10-01

    ... resins. 173.173 Section 173.173 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed...

  10. Plastic bronchitis

    National Research Council Canada - National Science Library

    Singhi, Anil Kumar; Vinoth, Bharathi; Kuruvilla, Sarah; Sivakumar, Kothandam

    2015-01-01

    Plastic bronchitis, a rare but serious clinical condition, commonly seen after Fontan surgeries in children, may be a manifestation of suboptimal adaptation to the cavopulmonary circulation with unfavorable hemodynamics...

  11. Visual and Plastic Arts in Teaching Literacy: Null Curricula?

    Science.gov (United States)

    Wakeland, Robin Gay

    2010-01-01

    Visual and plastic arts in contemporary literacy instruction equal null curricula. Studies show that painting and sculpture facilitate teaching reading and writing (literacy), yet such pedagogy has not been formally adopted into USA curriculum. An example of null curriculum can be found in late 19th - early 20th century education the USA…

  12. Comparative study of a three-bucket Savonius rotor with a combined three-bucket Savonius-three-bladed Darrieus rotor

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, R.; Biswas, A.; Sharma, K.K. [Department of Mechanical Engineering, National Institute of Technology (NIT), Silchar 788 010, Assam (India)

    2008-09-15

    The vertical axis wind turbines are simple in construction, self-starting, inexpensive and can accept wind from any direction without orientation. A combined Savonius-Darrieus type vertical axis wind rotor has got many advantages over individual Savonius or individual Darrieus wind rotor, such as better efficiency than Savonius rotor and high starting torque than Darrieus rotor. But works on the combined Savonius-Darrieus wind rotor are very scare. In view of the above, two types of models, one simple Savonius and the other combined Savonius-Darrieus wind rotors were designed and fabricated. The Savonius rotor was a three-bucket system having provisions for overlap variations. The Savonius-Darrieus rotor was a combination of three-bucket Savonius and three-bladed Darrieus rotors with the Savonius placed on top of the Darrieus rotor. The overlap variation was made in the upper part, i.e. the Savonius rotor only. These were tested in a subsonic wind tunnel available in the department. The various parameters namely, power coefficients and torque coefficients were calculated for both overlap and without overlap conditions. From the present investigation, it is seen that with the increase of overlap, the power coefficients start decreasing. The maximum power coefficient of 51% is obtained at no overlap condition. However, while comparing the power coefficients (C{sub p}) for simple Savonius-rotor with that of the combined configuration of Savonius-Darrieus rotor, it is observed that there is a definite improvement in the power coefficient for the combined Savonius-Darrieus rotor without overlap condition. Combined rotor without overlap condition provided an efficiency of 0.51, which is higher than the efficiency of the Savonius rotor at any overlap positions under the same test conditions. (author)

  13. Plastic Fishes

    CERN Multimedia

    Trettnak, Wolfgang

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness. The slideshow below gives you a taste of the artworks by Wolfgang Trettnak and Margarita Cimadevila.

  14. Plastic Bridge

    Institute of Scientific and Technical Information of China (English)

    履之

    1994-01-01

    Already ubiquitous in homes and cars, plastic is now appearing inbridges. An academic-industrial consortium based at the University ofCalifornia in San Diego is launching a three-year research program aimed atdeveloping the world’s first plastic highway bridge, a 450-foot span madeentirely from glass-,carbon,and polymer-fiber-reinforced composite mate-rials, the stuff of military aircraft. It will cross Interstate 5 to connect thetwo sides of the school’s campus.

  15. Melody of Autumn (oil painting)

    Institute of Scientific and Technical Information of China (English)

    1997-01-01

    Perhaps because of the nature of a woman, I take great interest in painting flowers and plants. But the difference is I prefer instead of the blooming flowers the dry flowers surviving the blossom. The dry cockscomb, sunflower, lotus and the wild flowers whose names I don’t know can always remind me of past stories. In recent years, my dried flawers have been displayed at exhibitions both at home and abroad and won appraisal and the top prize at the 1995 Eighth National Arts Exhibition. Some works have been collected by the China Art Gallery and private collectors from Hang Kong, Singapore, Taiwan and Europe.

  16. Monitoring temperature and pressure over surfaces using sensitive paints

    Science.gov (United States)

    Guerrero-Viramontes, J. Ascención; Moreno Hernández, David; Mendoza Santoyo, Fernando; Morán Loza, José Miguel; García Arreola, Alicia

    2007-03-01

    Two techniques for monitoring temperature and pressure variations over surfaces using sensitive paints are presented. The analysis is done by the acquisition of a set of images of the surface under analysis. The surface is painted by a paint called Pressure Sensitive Paint (PSP) for pressure measurements and Temperature Sensitive Paints (TSP) for temperature measurements. These kinds of paints are deposited over the surface under analysis. The recent experimental advances in calibration process are presented in this paper.

  17. GREEN PLASTIC: A NEW PLASTIC FOR PACKAGING

    OpenAIRE

    Mr. Pankaj Kumar*, Sonia

    2016-01-01

    This paper gives a brief idea about a new type of plastic called as bio-plastic or green plastic. Plastic is used as a packaging material for various products, but this plastic is made up of non renewable raw materials. There are various disadvantages of using conventional plastic like littering, CO2 production, non-degradable in nature etc. To overcome these problems a new type of plastic is discovered called bio-plastic or green plastic. Bio-plastic is made from renewable resources and also...

  18. Failure envelopes of bucket foundation subjected to combined loads%复合加载模式下桶形基础破坏包络面特性研究

    Institute of Scientific and Technical Information of China (English)

    武科; 栾茂田; 范庆来; 王志云

    2008-01-01

    As a new type of offshore foundation, the suction bucket foundation has been widely applied to soft ground in beach-shallow water. The response of the suction bucket foundation subjected to combined loads is therefore of significant importance for the design and construction of offshore foundation. Based on the Mohr-Coulomb yield criterion, a perfect elasto-plastic finite element method for numerical assessment of bearing capacity of bucket foundation under the combined loads was developed by virtue of the general-purpose FEM software ABAQUS. The failure envelopes in different loading spaces were generated. Then, the empirical calculation formulas were given according to the failure envelopes. Based on the relationship between the actual combined loading and the computed failure envelopes, the active state of bucket foundation could be evaluated, and it would be helpful in engineering practices.%桶形基础结构是一种适宜于滩海软黏土地基上的新型海洋基础形式.研究复合加载模式下桶形基础的承载力特性,并进而依此评价海洋平台基础及地基的稳定性是桶形基础设计与施工中的关键问题.针对软黏土地基上桶形基础结构,利用大型通用有限元分析软件ABAQUS,采用基于Mohr-Coulomb屈服准则的理想弹塑性本构模型,对复合加载模式下桶形基础的承载特性进行了三维弹塑性数值分析.在V-H、V-M、V-M-H空间内建立了复合加载模式下桶形基础极限承载力破坏包络图,推导了破坏包络面的经验计算公式,由此可根据实际的复合加载状态与数值计算所得的破坏包络曲面之间的相对关系,评判实际荷载作用下桶形基础的工作状态,为工程设计提供参考依据.

  19. Selective paint coatings for coloured solar absorbers: Polyurethane thickness insensitive spectrally selective (TISS) paints (Part II)

    Energy Technology Data Exchange (ETDEWEB)

    Orel, B.; Spreizer, H.; Surca Vuk, A.; Fir, M. [National Institute of Chemistry, Hajdrihova 19, SI-1000 Ljubljana (Slovenia); Merlini, D.; Vodlan, M. [Color d.d., Cesta komandanta Staneta 4, SI-1230 Medvode (Slovenia); Koehl, M. [Fraunhofer-Institute for Solar Energy Systems ISE, Heidenhofstr. 2, D-79110 Freiburg (Germany)

    2007-01-23

    Red, green and blue paints were prepared for use as thickness insensitive spectrally selective (TISS) paint coatings for solar facade absorbers. The paints were composed of a polyurethane resin binder in which various pigments were incorporated in such a way that they formed stable paint dispersions, satisfying stability criteria for facade coatings. A low emittance of the paints was achieved by using low-emittance aluminium flake pigments combined with iron oxide (red coloured paints). Black pigment was added to adjust solar absorptance. Blue and green paints were made by the addition of coloured aluminium flake pigment and the solar absorptance was also adjusted by the addition of black pigment. Efficiency for photo-thermal conversion of solar radiation was assessed by evaluation of the corresponding performance criteria, which enabled the selection of paints whose performance criteria values were higher than 0 (spectrally non-selective black coating). The results confirmed that blue and green paints and to minor extent red ones, combined selectivity with colour. The morphology of the paints was assessed, revealing that the colours originated from the deposition of finely dispersed colour and/or black pigment on the surface of the aluminium flakes during paint preparation. (author)

  20. Painting with Clay Van Gogh Style.

    Science.gov (United States)

    Skophammer, Karen

    1999-01-01

    Discusses Vincent Van Gogh's painting "Starry Night" and describes a lesson where fifth- and sixth-grade students created their own version of the artwork. Explains that the students utilized four colors of Permoplast clay, using their hands and fingers as brushes and blending tools and the clay as paint. (CMK)

  1. Detecting Corrosion Under Paint and Insulation

    Science.gov (United States)

    Bastin, Gary L.

    2011-01-01

    Corrosion is a major concern at the Kennedy Space Center in Florida due to the proximity of the center to the Atlantic Ocean and to salt water lagoons. High humidity, salt fogs, and ocean breezes, provide an ideal environment in which painted steel structures become corroded. Maintenance of painted steel structures is a never-ending process.

  2. Painted Beauties-East and West

    Institute of Scientific and Technical Information of China (English)

    VALERIE SARTOR

    2010-01-01

    @@ "Chinese painting, specifi-cally painting with ink or watercolors, has a different perspective from the way Western artists create images:" said my friend Ting Ting. She's a professional editor and she loves classical Chinese art. Ting Ting often invites me to attend gallery openings around Beijing.

  3. THz reflectometric imaging of medieval wall paintings

    DEFF Research Database (Denmark)

    Dandolo, Corinna Ludovica Koch; Jepsen, Peter Uhd

    2013-01-01

    Terahertz time-domain reflectometry has been applied to the investigation of a medieval Danish wall painting. The technique has been able to detect the presence of carbonblack layer on the surface of the wall painting and a buried insertion characterized by high reflectivity values has been found...... in depth of the lime-based historical plaster....

  4. Mural paintings deterioration – a multianalytical approach

    OpenAIRE

    Rosado, T; J. Mirão; Candeias, A J; Caldeira, A. T.

    2015-01-01

    This work presents a novel microanalytical approach in the mural paintings microbial diversity characterisation and identification of the damages promoted by their biological activity. Mortar microfragments, removed from visually biodegraded mural paintings, were analysed by several microscopic/spectroscopy techniques: variable pressure scanning electron microscopy coupled with energy dispersive X-ray spectrometry (VP-SEM-EDS), raman microspectrometry and infrared spectrometry in ...

  5. Digital color restoration of old paintings.

    Science.gov (United States)

    Pappas, M; Pitas, I

    2000-01-01

    Physical and chemical changes can degrade the visual color appearance of old paintings. Five digital color restoration techniques, which can be used to simulate the original appearance of paintings, are presented. Although a small number of color samples is employed in the restoration procedure, simulation results indicate that good restoration quality can be attained.

  6. Zhang Qing and His Meticulous Chinese Paintings

    Institute of Scientific and Technical Information of China (English)

    JULIE; M.SEGRAVES

    2002-01-01

    ZHANG Qing was initially drawn to the bird and flower paint-ings of the Tang and Song dynasties (7th-12th centuries). Later,Qing Dynasty (1644-1911) artist Ren Bonian, famous for hispaintings of figures, also became an important influence.Although Zhang Qing considers his style to be firmly rooted in tradi-

  7. P–y curves for bucket foundations in sand using finite element modeling

    DEFF Research Database (Denmark)

    Østergaard, Martin Underlin; Knudsen, Bjørn S.; Ibsen, Lars Bo

    2015-01-01

    Pile foundations for offshore wind turbines are often designed using p−y curves, where the soil reaction is given as a function of the pile displacement. The p−y curves are based on experiments done using slender piles, normally used in the oil and gas-industry. The monopiles commonly used today...... than a monopile, thus the before mentioned mismatch is even more pronounced. The purpose of this paper is to use 3D finite element modelling in PLAXIS 3D to establish a new p−y curve formulation for the bucket foundation in sand. The new formulation is based on the results of 18 numerical models...

  8. NUMERICAL SIMULATION OF 3-D AERATED JET BEHIND FLIP BUCKET OF OVERFLOW DAM

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Aerated jet,such as the jet flow behind the flip bucket of an overflow dam, widely exists in hydraulic engineering. Up to now the model test and prototype observation have been two main methods of studying the aerated jet for a special hydraulic project. In this paper, a three-dimensional mathematical model for the aerated jet was established. It seems that the suggested model has high predictive power by comparison with the results of model tests and prototype observations, which is very useful in the study of energy dissipation and jet flow atomization.

  9. Quicksort, largest bucket, and min-wise hashing with limited independence

    DEFF Research Database (Denmark)

    Knudsen, Mathias Bæk Tejs; Stöckel, Morten

    2015-01-01

    Randomized algorithms and data structures are often analyzed under the assumption of access to a perfect source of randomness. The most fundamental metric used to measure how “random” a hash function or a random number generator is, is its independence: a sequence of random variables is said...... being more practical. We provide new bounds for randomized quicksort, min-wise hashing and largest bucket size under limited independence. Our results can be summarized as follows. Randomized Quicksort. When pivot elements are computed using a 5-independent hash function, Karloff and Raghavan, J.ACM’93...

  10. Damping Estimation of a Prototype Bucket Foundation for Offshore Wind Turbines Identified by Full Scale Testing

    DEFF Research Database (Denmark)

    Damgaard, Mads; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

    2013-01-01

    -wind direction. Therefore, in order to assess the fatigue damage accumulation during the lifetime of the offshore wind turbine structure, a correct estimation of the cross-wind modal damping is necessary. This paper describes the cross-wind modal damping of the lowest eigenmode of a fully operational Vestas V90......-3.0 MW offshore wind turbine installed on a prototype bucket foundation. The foundation and the turbine tower are equipped with a monitoring system with 15 Kinemetrics force balance accelerometers and a Digitexx acquisition system. Using free vibration decays from “rotor-stop” tests and operational modal...

  11. Structural color painting by rubbing particle powder.

    Science.gov (United States)

    Park, ChooJin; Koh, Kunsuk; Jeong, Unyong

    2015-02-09

    Structural colors originate from purely physical structures. Scientists have been inspired to mimic the structures found in nature, the realization of these structures still presents a great challenge. We have recently introduced unidirectional rubbing of a dry particle powder on a rubbery surface as a quick, highly reproducible means to fabricate a single crystal monolayer assembly of particles over an unlimited area. This study extends the particle-rubbing process to a novel fine-art painting, structural color painting (SCP). SCP is based on structural coloring with varying iridescence according to the crystal orientation, as controlled by the rubbing direction. This painting technique can be applied on curved surfaces, which enriches the objects to be painted and helps the painter mimic the structures found in nature. It also allows for quick fabrication of complicated particle-assembly patterns, which enables replication of paintings.

  12. Subsurface Raman analysis of thin painted layers.

    Science.gov (United States)

    Conti, Claudia; Colombo, Chiara; Realini, Marco; Zerbi, Giuseppe; Matousek, Pavel

    2014-01-01

    Here we present, for the first time, an extension of spatially offset Raman spectroscopy to thin (tens of micrometers thick), highly turbid stratified media such as those encountered in paintings. The method permits the non-destructive interrogation of painted layers in situations where conventional Raman microscopy is not applicable due to high turbidity of the top layer(s). The concept is demonstrated by recovering the pure Raman spectra of paint sub-layers that are completely obscured by paint over-layers. Potential application areas include the analysis of paintings in art preservation and restoration avoiding the cross-sectional analysis used currently with this type of samples. The technique also holds promise for the development as a non-destructive subsurface tool for in situ analysis using portable instruments.

  13. Structural Color Painting by Rubbing Particle Powder

    Science.gov (United States)

    Park, Choojin; Koh, Kunsuk; Jeong, Unyong

    2015-02-01

    Structural colors originate from purely physical structures. Scientists have been inspired to mimic the structures found in nature, the realization of these structures still presents a great challenge. We have recently introduced unidirectional rubbing of a dry particle powder on a rubbery surface as a quick, highly reproducible means to fabricate a single crystal monolayer assembly of particles over an unlimited area. This study extends the particle-rubbing process to a novel fine-art painting, structural color painting (SCP). SCP is based on structural coloring with varying iridescence according to the crystal orientation, as controlled by the rubbing direction. This painting technique can be applied on curved surfaces, which enriches the objects to be painted and helps the painter mimic the structures found in nature. It also allows for quick fabrication of complicated particle-assembly patterns, which enables replication of paintings.

  14. Degradation of wall paints due to sodium sulphate and sodium chloride crystallization

    Directory of Open Access Journals (Sweden)

    Díaz Gonçalves, T.

    2003-03-01

    Full Text Available A test method for evaluating wall paints behaviour to soluble salts crystallization was developed at LNEC. in the present paper, a recent set of tests is described and discussed. The major objectives were: analysing and comparing the behaviour of a common emulsion {"plastic" paint and a silicate-based paint; observing and comparing the effect of sodium sulphate, sodium chloride and distilled water on the paints and on a non-painted stone; evaluating this test method adequacy and effectiveness. The silicate-based paint showed a resistance to soluble salts crystallization greater than the one of the plastic paint. However, the degradation pattern of the silicate-based paint (blistering of a filmic layer was similar to the one of organic paints and distinct from the one of pure mineral paints. The amount of damage that a saline solution can cause to wall paints cannot be inferred from the amount of damage it can cause to stone. Sodium chloride seems to be able to cause more severe degradation to wall paints than sodium sulphate. To the unpainted stone, sodium sulphate seems to be more damaging than sodium chloride. The test method seems adequate to observe and compare the behaviour of wall paints under soluble salts action. However, lower (around 0.5% concentrations for both sodium sulphate and sodium chloride should be tested in the future.

    RESUMEN En el LNEC se desarrolló una metodología de ensayo para evaluar la respuesta de pinturas aplicadas sobre paredes, frente a la cristalización de sales solubles. En este trabajo, se describen y discuten un conjunto de ensayos recientes. Los principales objetivos fueron: el análisis y la comparación del comportamiento de una pintura de emulsión común {''pintura plástica" y la de una pintura de silicato; la observación y la comparación de los efectos del sulfato de sodio, del cloruro de sodio y del agua destilada sobre las pinturas y sobre piedra no pintada; la evaluación de la adecuaci

  15. Plastic condoms.

    Science.gov (United States)

    1968-01-01

    Only simple equipment, simple technology and low initial capital investment are needed in their manufacture. The condoms can be made by people who were previously unskilled or only semi-skilled workers. Plastic condoms differ from those made of latex rubber in that the nature of the plastic film allows unlimited shelf-life. Also, the plastic has a higher degree of lubricity than latex rubber; if there is a demand for extra lubrication in a particular market, this can be provided. Because the plastic is inert, these condoms need not be packaged in hermetically sealed containers. All these attributes make it possible to put these condoms on the distributors' shelves in developing countries competitively with rubber condoms. The shape of the plastic condom is based on that of the lamb caecum, which has long been used as luxury-type condom. The plastic condom is made from plastic film (ethylene ethyl acrilate) of 0.001 inch (0.0254 mm.) thickness. In addition, a rubber ring is provided and sealed into the base of the condom for retention during coitus. The advantage of the plastic condom design and the equipment on which it is made is that production can be carried out either in labour-intensive economy or with varying degrees of mechanization and automation. The uniform, finished condom if made using previously untrained workers. Training of workers can be done in a matter of hours on the two machines which are needed to produce and test the condoms. The plastic film is provided on a double wound roll, and condom blanks are prepared by means of a heat-sealing die on the stamping machine. The rubber rings are united to the condom blanks on an assembly machine, which consists of a mandrel and heat-sealing equipment to seal the rubber ring to the base of the condom. Built into the assembly machine is a simple air-testing apparatus that can detect the smallest pinhole flaw in a condom. The manufacturing process is completed by unravelling the condom from the assembly

  16. A load-displacement based approach to assess the bearing capacity and deformations of mono-bucket foundations

    DEFF Research Database (Denmark)

    Vahdatirad, Mohammadjavad; Diaz, Alberto Troya; Nielsen, Søren

    2016-01-01

    It is now accepted that a larger effort must be made in order to optimize the design so that offshore wind turbines can be competitive with the other energy resources. In this regard, mono-buckets are known as a cost-effective offshore foundation solution. In the current study, a load–displacemen......It is now accepted that a larger effort must be made in order to optimize the design so that offshore wind turbines can be competitive with the other energy resources. In this regard, mono-buckets are known as a cost-effective offshore foundation solution. In the current study, a load...

  17. Plastic Bronchitis.

    Science.gov (United States)

    Rubin, Bruce K

    2016-09-01

    Plastic bronchitis is an uncommon and probably underrecognized disorder, diagnosed by the expectoration or bronchoscopic removal of firm, cohesive, branching casts. It should not be confused with purulent mucous plugging of the airway as seen in patients with cystic fibrosis or bronchiectasis. Few medications have been shown to be effective and some are now recognized as potentially harmful. Current research directions in plastic bronchitis research include understanding the genetics of lymphatic development and maldevelopment, determining how abnormal lymphatic malformations contribute to cast formation, and developing new treatments. Copyright © 2016 Elsevier Inc. All rights reserved.

  18. Results of investigating the load on carrying parts of the Rs-1200 bucket wheel excavator

    Energy Technology Data Exchange (ETDEWEB)

    Tasev, D.; Mikhalkov, Z.; Tokmakchiev, S.

    1983-08-01

    Overburden removal in the Maritsa Iztok coal basin is carried out by Rs-1200 bucket wheel excavators under continuously worsening working conditions. The depth and cutting resistance of overburden require use of more powerful excavators. In order to determine whether the Rs-1200 excavator has enough power to be employed under worsening conditions the stress at critical points of the boom was measured under static and dynamic loads by means of the TSA-4A tensometer, UM-131 measuring device and N-115 vibration recorder. It was found that the stresses at critical points of the boom do not exceed 5,400-5,900 N/cm/SUP/2 under static or dynamic loads. The combined static and dynamic loads do not cause stresses over 9,100 N/cm/SUP/2. Investigations show that the power of the electric motor driving the bucket wheel can be increased by about 30%. Details of measuring techniques and results of load testing are given. (In Bulgarian)

  19. One method for life time estimation of a bucket wheel machine for coal moving

    Science.gov (United States)

    Vîlceanu, Fl; Iancu, C.

    2016-08-01

    Rehabilitation of outdated equipment with lifetime expired, or in the ultimate life period, together with high cost investments for their replacement, makes rational the efforts made to extend their life. Rehabilitation involves checking operational safety based on relevant expertise of metal structures supporting effective resistance and assessing the residual lifetime. The bucket wheel machine for coal constitute basic machine within deposits of coal of power plants. The estimate of remaining life can be done by checking the loading on the most stressed subassembly by Finite Element Analysis on a welding detail. The paper presents step-by-step the method of calculus applied in order to establishing the residual lifetime of a bucket wheel machine for coal moving using non-destructive methods of study (fatigue cracking analysis + FEA). In order to establish the actual state of machine and areas subject to study, was done FEA of this mining equipment, performed on the geometric model of mechanical analyzed structures, with powerful CAD/FEA programs. By applying the method it can be calculated residual lifetime, by extending the results from the most stressed area of the equipment to the entire machine, and thus saving time and money from expensive replacements.

  20. Assessment of snowfall accumulation underestimation by tipping bucket gauges in the Spanish operational network

    Science.gov (United States)

    Buisán, Samuel T.; Earle, Michael E.; Luís Collado, José; Kochendorfer, John; Alastrué, Javier; Wolff, Mareile; Smith, Craig D.; López-Moreno, Juan I.

    2017-03-01

    Within the framework of the World Meteorological Organization Solid Precipitation Intercomparison Experiment (WMO-SPICE), the Thies tipping bucket precipitation gauge was assessed against the SPICE reference configuration at the Formigal-Sarrios test site located in the Pyrenees mountain range of Spain. The Thies gauge is the most widely used precipitation gauge by the Spanish Meteorological State Agency (AEMET) for the measurement of all precipitation types including snow. It is therefore critical that its performance is characterized. The first objective of this study is to derive transfer functions based on the relationships between catch ratio and wind speed and temperature. Multiple linear regression was applied to 1 and 3 h accumulation periods, confirming that wind is the most dominant environmental variable affecting the gauge catch efficiency, especially during snowfall events. At wind speeds of 1.5 m s-1 the tipping bucket recorded only 70 % of the reference precipitation. At 3 m s-1, the amount of measured precipitation decreased to 50 % of the reference, was even lower for temperatures colder than -2 °C and decreased to 20 % or less for higher wind speeds.The implications of precipitation underestimation for areas in northern Spain are discussed within the context of the present analysis, by applying the transfer function developed at the Formigal-Sarrios and using results from previous studies.

  1. Mixed plastics recycling technology

    CERN Document Server

    Hegberg, Bruce

    1995-01-01

    Presents an overview of mixed plastics recycling technology. In addition, it characterizes mixed plastics wastes and describes collection methods, costs, and markets for reprocessed plastics products.

  2. KLIMT, FROM PAINTING TO FASHION

    Directory of Open Access Journals (Sweden)

    URDEA Olimpia

    2015-05-01

    Full Text Available Fashion has been a subject for most fields of art, starting from visual arts to cinema and literature. The metamorphoses of fashion, an art in itself, are under the sign of history that marked the social during the evolution of humanity. The present paper makes a reference to the links between fashion and Klimt’s work. Klimt proved to be a visionary by means of his visual, unique and unmistakable signature concerning the way he treated the clothed woman. As he worshipped the female body, he portrayed it, reflecting the fashion style of an era that was meant to be renewed. His work, strongly influenced by feminine values, became conspicuous as a manifesto against the rigidity of the Viennese society in the late nineteenth century and early twentieth century. The modernity of Klimt’s vision generated the metamorphosis of the woman model, from the corseted woman until that time, and not only in terms of fashion, to the freed woman, using the metaphorical instruments of his art. The artist’s complex creativity helps us find him in four different situations, all in close connection with fashion art: the painter Klimt, who portrays woman who shows herself by showing her garment; the fashion designer Klimt who suggests outfits for his collaborator, Emilie Flöge, remoulding the dress as a clothing item; the fashion photographer from the photographs of Emilie Flöge wearing his creations; and, indirectly, by his paintings from the cycle Women, which had a powerful impact on contemporary fashion. Such a complex, visionary creator, whose painting and fashion interfere, is worth mentioning for his contribution to the fashion art avatars.

  3. Occupational risk assessment of paint industry workers

    Directory of Open Access Journals (Sweden)

    Hugo M de Oliveira

    2011-01-01

    Full Text Available Background: Thousands of chemical compounds are used in paint products, like pigments, extenders, binders, additives, and solvents (toluene, xylene, ketones, alcohols, esters, and glycol ethers. Paint manufacture workers are potentially exposed to the chemicals present in paint products although the patterns and levels of exposure to individual agents may differ from those of painters. The aim of the present study was to evaluate genome damage induced in peripheral blood lymphocytes and oral mucosa cells of paint industry workers. Materials and Methods: Genotoxicity was evaluated using the alkaline Comet assay in blood lymphocytes and oral mucosa cells, and the Micronucleus test in oral mucosa cells. For the micronucleus test in exfoliated buccal cells, no significant difference was detected between the control and paint industry workers. Results: The Comet assay in epithelia buccal cells showed that the damage index (DI and damage frequency (DF observed in the exposed group were significantly higher relative to the control group ( P≤0.05. In the same way, the Comet assay data in peripheral blood leukocytes showed that both analysis parameters (DI and DF were significantly greater than that for the control group ( P≤0.05. Conclusions: Chronic occupational exposure to paints may lead to a slightly increased risk of genetic damage among paint industry workers.

  4. Plastic fish

    CERN Multimedia

    Antonella Del Rosso

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness.   Artwork by Wolfgang Trettnak. Packaging materials, consumer goods (shoes, kids’ toys, etc.), leftovers from fishing and aquaculture activities… our oceans and beaches are full of plastic litter. Most of the debris from beaches is plastic bottles. “PET bottles have high durability and stability,” explains Wolfgang Trettnak, a chemist by education and artist from Austria, who gave a lecture on this topic organised by the Staff Association at CERN on 26 May. “PET degrades very slowly and the estimated lifetime of a bottle is 450 years.” In addition to the beach litter accumulated from human use, rivers bring several ki...

  5. Plastic zonnecellen

    NARCIS (Netherlands)

    Roggen, Marjolein

    1998-01-01

    De zonnecel van de toekomst is in de maak. Onderzoekers van uiteenlopend pluimage werken eendrachtig aan een plastic zonnecel. De basis is technisch gelegd met een optimale, door invallend licht veroorzaakte, vorming van ladingdragers binnen een composiet van polymeren en buckyballs. Nu is het zaak

  6. Bucket elevator

    OpenAIRE

    2016-01-01

    Cílem této bakalářské práce je návrh svislého korečkového elevátoru, který má sloužit k dopravě obilovin s dopravní výškou 19 m a dopravovaným množstvím 100 t/hod. Práce se skládá z popisu korečkového elevátoru a jeho hlavních částí, zmiňující se v úvodní rešerši. Tato práce je zaměřena na funkční a kapacitní výpočet, určení pohonu a napínacího zařízení. Další výpočet je kontrolní, skládající se z pevnostní kontroly hnacího hřídele, výpočtu pera, životnosti ložisek a výpočtu napínacího zaříze...

  7. PAINT SUPPLIES AND LOCATION: EXAMINING ICI

    Directory of Open Access Journals (Sweden)

    M. Herron

    2016-01-01

    Full Text Available How important is location to an international retailer? Not just any retailer but the second largest paint retailer in the world. Imperial Chemical Industries (ICI was a British chemical company and was at one stage the largest manufacturer in Britain. Formed from the merger of several leading British chemical companies in 1926, ICI makes paints and speciality products, including food ingredients, speciality polymers, electronic materials, fragrances and flavourings. ICI paints purchased the Cleveland Ohiobased Glidden Coatings & Resins (Glidden Paint Company in 1986 for USD$580 million. The addition of Glidden to ICI's North American operations more than doubled that subsidiary's annual sales to $3 billion and increased ICI's corporate presence in the United States dramatically. A decline in paint and solvent consumption during the 2000 decade slowed the average growth of the paint industry to about 2% annually. Rauch Associates, the leading US paint analyst firm, predicted near-term growth to slow even further to 1.2% per annum. Through the 1990’s and early 2000’s Glidden paint was sold only through Glidden-badged paint stores and smaller retailers under licence, developing a strong identifiable brand and reputation. How were potential Glidden retail paint store locations chosen across America to enable and support this market growth? This paper investigates the real process that was developed and applied to construct a national network of retail outlets across the United States. It also highlights the change in direction that occurred at ICI paints culminating in its eventual acquisition by AkzoNobel in 2008 who immediately sold parts of ICI to Henkel, and integrated ICI's remaining operations within its existing organisation. This sale and the associated corporate restructure caused considerable change in marketing directions allowing for the first time the selling of Glidden paint products to mass market centres

  8. Nanjing Children’s Painting & Calligraphy Association

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    THE Nanjing Children’s Painting and Calligraphy Association,founded in 1982,is an organization engaged in the training, composition.exhibition and exchange of children’s painting and calligraphy.The association boasts a group of prestigious painters and calligraphers at home and abroad as its consultants,its membership exceeding 400.The Nanjing Children’s Painting and Calligraphy Association has had a collection of over 6,000 art works attend exhibitions held in more than 30 countries and regions worldwide.

  9. 24 CFR 35.135 - Use of paint containing lead.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Use of paint containing lead. 35... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a...

  10. 24 CFR 3280.814 - Painting of wiring.

    Science.gov (United States)

    2010-04-01

    ... wires, as the color coding may be obliterated by the paint. ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Painting of wiring. 3280.814... Painting of wiring. During painting or staining of the manufactured home, it shall be permitted to...

  11. Edge-Based Shading as a Depth Cue in Paintings

    NARCIS (Netherlands)

    Venderbosch, M. E.; van Doorn, Andrea J; Koenderink, Jan J; te Pas, Susan F

    2015-01-01

    We explored how an artist who uses a particular monochrome modern painting style generates the impression of relief in paintings. Three portraits, painted after model, were created especially for the experiment. Photographs of the paintings were presented on a computer screen. To investigate the per

  12. Historical origins of Petrykivsky decorative painting

    Directory of Open Access Journals (Sweden)

    T. A. Harkava

    2017-07-01

    Full Text Available Petrykivsky decorative painting is a part of Ukrainian folk art. Domestic science of folk art has originated and has been developing primarily as a study of archaeological antiquities and artistic monuments of the past. Scientific papers, which comprehended the process of folk art development, began to appear in the late nineteenth century, Archaeological Congresses became the impetus for their appearance. Being a representative of the decorative painting, Petrikivsky decorative painting is rooted by its murals to Tripoli. It was created as a peasant domestic drawing. Inexhaustible diversity of local variants of Petrikivsky decorative painting, its evolutionary change, the individual characteristics of paintings of hundreds of famous Ukrainian artists do not even allow comparing it to any other European counterparts, each of which is characterized only by some individual techniques. Petrikivsky decorative painting got the significant boost in its distribution and development when it «came down» from walls to paper. Paper pictures - malyovky - were stucked to walls following the traditional rules of domestic interior’s decoration. Petrikivsky decorative painting got the official status in 1913, when E. Evenbah, by the initiative of D.I. Yavornytsky, gathered the collection of Petrikivsky decorative painting’s malyovkas and organized the exhibition in St. Petersburg. Motives of painting are rooted into the local flora and fauna and into the historical tradition. However, Petrikivsky decorative painting is not a direct reflection of natural motifs. World, created in paintings, is the product of the imagination of folk artist, it is the stylization of local flowers, fruits and birds. First names of Masters of Petrikivsky decorative painting, which appeared in historical sources, were T. Pata, N. Bilokin, I. Pavlenko. Their official recognition happened in 1930 after their participation in the first republican exhibition, which was later shown

  13. RITMO Y ESPACIO EN LA PINTURA BIZANTINA Rhythm and space in byzantine painting

    Directory of Open Access Journals (Sweden)

    Federico José Xamist

    2011-10-01

    Full Text Available Durante el siglo XX se lleva a cabo una revalorización de la pintura del medioevo heleno, ignorada durante todo el clasicismo europeo. AAnte la constatación de que el espacio representado en la pintura bizantina no reproduce el espacio natural se llega a la conclusión de que las operaciones pictóricas aplicadas por los pintores bizantinos tienen como objeto simbolizar un espacio sobrenatural. En las siguientes líneas intentaremos abrir la problemática del espacio en la pintura bizantina a una interpretación plástica, es decir, intentaremos presentar una lectura de las operaciones pictóricas en cuanto tales siguiendo los planteamientos de Georgos Kordis, profesor de la cátedra Eikonografia de la Facultad de Teología de la Universidad de Atenas y destacado pintor griego. Nuestro objetivo es plantear algunas directrices para introducirnos en la problemática pictórica de la representación del espacio en la pintura bizantina.During the twentieth century is carried out a revaluation of the Hellenic medieval painting, ignored during the European classicism. Given the finding that the space represented in Byzantine painting does not reproduce the natural space leads to the conclusion that painting operations implemented by the Byzantine painters are intended to symbolize a supernatural space. The following lines try to open the question of space in painting plastic Byzantine interpretation, ie to try to present a reading of the painting operations as such, following the approach of Georges Kordis, chair professor of the Faculty Eikonografia Theology of the University of Athens and prominent Greek painter. Our goal is to propose some guidelines for introducing us to the problem of pictorial representation of space in the Byzantine painting.

  14. Plastic Surgery Statistics

    Science.gov (United States)

    ... PSN PSEN GRAFT Contact Us News Plastic Surgery Statistics Plastic surgery procedural statistics from the American Society of Plastic Surgeons. Statistics by Year Print 2016 Plastic Surgery Statistics 2015 ...

  15. Effect of paint on vapour resistivity in plaster

    Directory of Open Access Journals (Sweden)

    de Villanueva, L.

    2008-12-01

    Full Text Available The vapour resistivity of plaster coatings such as paint and their effectiveness as water repellents were studied in several types of plaster. To this end, painted, unpainted and pigmented specimens were tested. Experimental values were collected on diffusion and vapour permeability, or its inverse, water vapour resistivity.The data obtained were very useful for evaluating moisture exchange between plaster and the surrounding air, both during initial drying and throughout the life of the material. They likewise served as a basis for ensuring the proper evacuation of water vapour in walls, and use of the capacity of the porous network in plaster products to regulate moisture content or serve as a water vapour barrier to avoid condensation.Briefly, the research showed that pigments, water-based paints and silicon-based water repellents scantly raised vapour resistance. Plastic paints, enamels and lacquers, however, respectively induced five-, ten- and twenty-fold increases in vapour resistivity, on average.Se estudia el fenómeno de la resistividad al vapor de los de yeso y el efecto impermeabilizante que producen los recubrimientos de pintura sobre diversos tipos de yeso y escayola. Para ello, se ensayan probetas desnudas y recubiertas con distintos tipos de pintura, así como coloreados en masa. Se obtienen valores experimentales de la difusividad o permeabilidad al vapor o su inverso la resistividad al vapor de agua.Los datos obtenidos son muy útiles para valorar el fenómeno del intercambio de humedad entre el yeso y el ambiente, tanto durante el proceso de su secado inicial, como en el transcurso de su vida. Así como para disponer soluciones adecuadas para la evacuación del vapor de agua a través de los cerramientos, para utilizar la capacidad de regulación de la humedad, que proporciona el entramado poroso de los productos de yeso, o para impedir el paso del vapor de agua y evitar condensaciones.Como resumen de la investigación, se

  16. Standard Operating Procedure for the Preparation of Lead-Containing Paint Films and Lead-in-Paint Diagnostic Test Materials

    Science.gov (United States)

    This SOP describes the preparation of stand-alone, lead paint films, prepared according to the old paint recipes. Further, this SOP describes the use of these paint films for the preparation of simulated old paints on a variety of substrates. Substrates used included wood, stee...

  17. On the performance of bursty and modulated sources subject to leaky bucket rate-based access control schemes

    Science.gov (United States)

    Sohraby, Khosrow; Sidi, Moshe

    1994-02-01

    In this paper, we provide the analysis of a rate-based access control scheme in high speed environments based on a buffered leaky bucket algorithm. The analysis is carried out in discrete time which is representative of an ATM environment. For the cell arrivals to the leaky bucket, we consider a general discrete Markovian arrival process which models bursty and modulated sources. The key of our analysis is the introduction of the deficit function that allows the reduction of the original problem to a more standard discrete time queueing system with the same arrival process. As an important special case, the detailed analysis of the Binary Markov Source throttled by such rate-based access control schemes is presented. Along with explicit recursions for computation of state probabilities and simple characterization of the asymptotic behavior of the queue build up, some guidelines for the parameter selection of these schemes are provided. Our results indicate that for sources with relatively large active periods, for an acceptable grade-of-service at the input queue, the token generation rate should be chosen to be close to the peak rate of the source, and increasing the bucket size of the leaky bucket does not improve substantially the performance at the input queue.

  18. A load-displacement based approach to assess the bearing capacity and deformations of mono-bucket foundations

    DEFF Research Database (Denmark)

    Vahdatirad, Mohammadjavad; Diaz, Alberto Troya; Nielsen, Søren

    2016-01-01

    It is now accepted that a larger effort must be made in order to optimize the design so that offshore wind turbines can be competitive with the other energy resources. In this regard, mono-buckets are known as a cost-effective offshore foundation solution. In the current study, a load...

  19. Modelling the drained response of bucket foundations for offshore wind turbines under general monotonic and cyclic loading

    DEFF Research Database (Denmark)

    Foglia, Aligi; Gottardi, Guido; Govoni, Laura;

    2015-01-01

    The response of bucket foundations on sand subjected to planar monotonic and cyclic loading is investigated in the paper. Thirteen monotonic and cyclic laboratory tests on a skirted footing model having a 0.3 m diameter and embedment ratio equal to 1 are presented. The loading regime reproduces t...

  20. Terahertz imaging for non-destructive evaluation of mural paintings

    Science.gov (United States)

    Jackson, J. B.; Mourou, M.; Whitaker, J. F.; Duling, I. N.; Williamson, S. L.; Menu, M.; Mourou, G. A.

    2008-02-01

    The feasibility of applying time-domain, terahertz spectroscopic imaging to the evaluation of underdrawings and paint layers embedded within wall paintings is demonstrated. Metallic and dielectric paint patterns and a graphite drawing are resolved through both paint and plaster overlayers using a pulsed-terahertz reflectometer and imaging system. We calculated the bulk refractive indices of four common pigments and used them to confirm color domains in a terahertz-beam spectral image of a painting.

  1. IDENTIFICATION OF BACTERIA IN LATEX PAINTS

    Directory of Open Access Journals (Sweden)

    Rojas, J.

    2008-01-01

    Full Text Available The bacteria are prokaryote organisms with a high capacity to colonize many types of habits. This research was developed with the object to identify extremophiles bacteria presents in latex paint. The bacteria were cultivated in culture mediums TSA, Blood Agar, Mc Conkey and finally the biochemical proof API-NF® for bacteria's isolation and identification, respectively. Characterization showed bacterial profile of Pasteurella sp. Hypothesis that could be found extremophiles bacteria in latex paint were demonstrated.

  2. Paintings in Atlantic Megalithic Art: Barnenez

    OpenAIRE

    Bueno Ramírez, Primitiva; de Balbín Behrmann, Rodrigo; Laporte, Luc; Gouezin, Philippe; Barroso Bermejo, Rosa; Hernanz Gismero, Antonio; Gavira-Vallejo, José M.; Iriarte Cela, Mercedes

    2012-01-01

    The use of technique is usually considered in European megalithic art as an indicator of the level of culture sophistication attained by a particular community. Traditionally, it was considered that only the Iberian Peninsula is home to painted dolmens. The analysis of chamber H of the Barnenez tumulus together with some information scattered over the continent, prove that painting was part of the graphic programs in the most archetypal Atlantic sites, such as Brittany. A highly rewarding pan...

  3. Plastic bronchitis

    Directory of Open Access Journals (Sweden)

    Anil Kumar Singhi

    2015-01-01

    Full Text Available Plastic bronchitis, a rare but serious clinical condition, commonly seen after Fontan surgeries in children, may be a manifestation of suboptimal adaptation to the cavopulmonary circulation with unfavorable hemodynamics. They are ominous with poor prognosis. Sometimes, infection or airway reactivity may provoke cast bronchitis as a two-step insult on a vulnerable vascular bed. In such instances, aggressive management leads to longer survival. This report of cast bronchitis discusses its current understanding.

  4. A quantitative approach to painting styles

    Science.gov (United States)

    Vieira, Vilson; Fabbri, Renato; Sbrissa, David; da Fontoura Costa, Luciano; Travieso, Gonzalo

    2015-01-01

    This research extends a method previously applied to music and philosophy (Vilson Vieira et al., 2012), representing the evolution of art as a time-series where relations like dialectics are measured quantitatively. For that, a corpus of paintings of 12 well-known artists from baroque and modern art is analyzed. A set of 99 features is extracted and the features which most contributed to the classification of painters are selected. The projection space obtained provides the basis to the analysis of measurements. These quantitative measures underlie revealing observations about the evolution of painting styles, specially when compared with other humanity fields already analyzed: while music evolved along a master-apprentice tradition (high dialectics) and philosophy by opposition, painting presents another pattern: constant increasing skewness, low opposition between members of the same movement and opposition peaks in the transition between movements. Differences between baroque and modern movements are also observed in the projected "painting space": while baroque paintings are presented as an overlapped cluster, the modern paintings present minor overlapping and are disposed more widely in the projection than the baroque counterparts. This finding suggests that baroque painters shared aesthetics while modern painters tend to "break rules" and develop their own style.

  5. Implicit and explicit features of paintings.

    Science.gov (United States)

    Marković, Slobodan; Radonjić, Ana

    2008-01-01

    Implicit features of the paintings are properties that are imposed by the observer (e.g. how pleasant, interesting, tense a painting appears), whereas explicit features refer to properties that can be directly perceived (form, color, depth, etc.). The aim of Experiments 1 and 2 was to investigate the underlying structure of implicit and explicit features of paintings using the factor analysis of elementary judgments. In the preliminary studies, representative sets of paintings and elementary implicit and explicit dimensions (in the form of bipolar scales) were selected. Four implicit factors were extracted: Regularity, Relaxation, Hedonic Tone and Arousal. Four explicit factors were extracted: Form, Color, Space and Complexity. The following significant correlations between implicit and explicit factors were obtained: Regularity-Form, Regularity-Space, Hedonic Tone-Form and Arousal-Complexity. In Experiment 3 the role of implicit and explicit factors in similarity-dissimilarity ratings was specified. Significant correlations between the position of paintings in MDS space and mean judgments of explicit factors Color, Space and Complexity and implicit factor Relaxation were obtained, suggesting that similarity ratings of paintings are primarily based on explicit features. The causal relation of explicit and implicit features is discussed.

  6. Multi-leg Seat Inventory Control Based on EMSU and Virtual Bucket

    Directory of Open Access Journals (Sweden)

    Wei Fan

    2014-01-01

    Full Text Available Expected marginal seat revenue (EMSR is a well-known method for airline seat inventory control airlines. However, this method employs a static model to study the dynamic reservation process, and does not take into account the risk tolerance of policy makers. Expected marginal seat utility (EMSU replaces revenue by utility, which addresses the real situation of seat inventory control. However, there is still a lack of multi-leg seat control algorithms based on EMSU. Therefore, using EMSU and bucket algorithms, this paper applies the Markov decision-making process to simulate the flight reservation process and builds a dynamic multi-leg seat inventory control model. Experimental results validate the effectiveness of the proposed method.

  7. Systems approach to modeling the Token Bucket algorithm in computer networks

    Directory of Open Access Journals (Sweden)

    Ahmed N. U.

    2002-01-01

    Full Text Available In this paper, we construct a new dynamic model for the Token Bucket (TB algorithm used in computer networks and use systems approach for its analysis. This model is then augmented by adding a dynamic model for a multiplexor at an access node where the TB exercises a policing function. In the model, traffic policing, multiplexing and network utilization are formally defined. Based on the model, we study such issues as (quality of service QoS, traffic sizing and network dimensioning. Also we propose an algorithm using feedback control to improve QoS and network utilization. Applying MPEG video traces as the input traffic to the model, we verify the usefulness and effectiveness of our model.

  8. Structural Optimization of an Offshore Wind Turbines Transition Pieces for Bucket Foundations

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    as an alternative to steel. CRC has an excellent durability and higher compressive strength compared to traditional concrete. This material has also an increased ductility owing to integration of large contents of short, strong and stiff steel fibres. At present, application of high-tension concrete is limited......Traditionally, offshore constructions are made of steel. The focus of this paper is optimization of a transition piece (TP) connecting the offshore wind turbine column with a suction bucket foundation. Suction caissons, typically used for shallow water depths, have been proved to be adequate...... offshore, mainly, to making a grouting connection of a transition piece to a monopile. Lack of standards and norms puts additional restriction on application of CRC. In the earlier work, the structural performance of transition pieces with a conical shape was compared for a 5 MW offshore wind turbine...

  9. Dynamic response of jetting and cementing bucket platform to wave and current loading

    Institute of Scientific and Technical Information of China (English)

    Wang Hu; Wang Deyu

    2006-01-01

    The jetting and cementing bucket platform (JCBP) is a new type offshore oil-drilling platform. This paper aims to establish an analysis method for calculating the dynamic response of this platform. Based on the theory of elastic half space, the dynamic stiffness and damping of the platform's foundation were obtained and attached to the end of the platform's main jackets as a boundary condition. Then using finite element method (FEM), the dynamic response of the platform due to wave and current loading was calculated. Furthermore, the whole platform's finite element model was established and the dynamic response of the platform was calculated. The numerical results demonstrate that the present method by the usage of elastic half space theory and FEM is simple and it is reliable and efficient to calculate dynamic behavior of the platform in response to wave and current loading.

  10. Seepage Study for Suction Installation of Bucket Foundation in Different Soil Combinations

    DEFF Research Database (Denmark)

    Koteras, Aleksandra Katarzyna; Ibsen, Lars Bo; Clausen, Johan Christian

    2016-01-01

    and different boundaries. The flow of pore water is studied for homogenous sand, sand overlaid by impermeable layer and sand situated above impermeable layer. In all three cases the seepage analysis gives the required information on the critical suction pressure and on the distribution of excess pore pressure...... around the bucket skirt. The exceedance of critical suction might lead to installation failure due to formation of piping channels, which break the hydraulic seal between the skirt and soil. The excess pore pressure arising due to applied suction changes the effective stress, hence the penetration...... resistance of soil. Therefore, both matters are important for the design. The results show that the appearance of the impermeable layer above or below sand affects the excess pore pressure in this layer. Moreover, it has been found that the appearance of impermeable layer increases the allowable suction...

  11. Assessment of measurement errors and dynamic calibration methods for three different tipping bucket rain gauges

    Science.gov (United States)

    Shedekar, Vinayak S.; King, Kevin W.; Fausey, Norman R.; Soboyejo, Alfred B. O.; Harmel, R. Daren; Brown, Larry C.

    2016-09-01

    Three different models of tipping bucket rain gauges (TBRs), viz. HS-TB3 (Hydrological Services Pty Ltd.), ISCO-674 (Isco, Inc.) and TR-525 (Texas Electronics, Inc.), were calibrated in the lab to quantify measurement errors across a range of rainfall intensities (5 mm·h- 1 to 250 mm·h- 1) and three different volumetric settings. Instantaneous and cumulative values of simulated rainfall were recorded at 1, 2, 5, 10 and 20-min intervals. All three TBR models showed a substantial deviation (α = 0.05) in measurements from actual rainfall depths, with increasing underestimation errors at greater rainfall intensities. Simple linear regression equations were developed for each TBR to correct the TBR readings based on measured intensities (R2 > 0.98). Additionally, two dynamic calibration techniques, viz. quadratic model (R2 > 0.7) and T vs. 1/Q model (R2 = > 0.98), were tested and found to be useful in situations when the volumetric settings of TBRs are unknown. The correction models were successfully applied to correct field-collected rainfall data from respective TBR models. The calibration parameters of correction models were found to be highly sensitive to changes in volumetric calibration of TBRs. Overall, the HS-TB3 model (with a better protected tipping bucket mechanism, and consistent measurement errors across a range of rainfall intensities) was found to be the most reliable and consistent for rainfall measurements, followed by the ISCO-674 (with susceptibility to clogging and relatively smaller measurement errors across a range of rainfall intensities) and the TR-525 (with high susceptibility to clogging and frequent changes in volumetric calibration, and highly intensity-dependent measurement errors). The study demonstrated that corrections based on dynamic and volumetric calibration can only help minimize-but not completely eliminate the measurement errors. The findings from this study will be useful for correcting field data from TBRs; and may have major

  12. Transmissibility of the Ice Bucket Challenge among globally influential celebrities: retrospective cohort study

    Science.gov (United States)

    Chan, Brandford H Y; Leung, Gabriel M; Lau, Eric H Y; Pang, Herbert

    2014-01-01

    Objectives To estimate the transmissibility of the Ice Bucket Challenge among globally influential celebrities and to identify associated risk factors. Design Retrospective cohort study. Setting Social media (YouTube, Facebook, Twitter, Instagram). Participants David Beckham, Cristiano Ronaldo, Benedict Cumberbatch, Stephen Hawking, Mark Zuckerberg, Oprah Winfrey, Homer Simpson, and Kermit the Frog were defined as index cases. We included contacts up to the fifth generation seeded from each index case and enrolled a total of 99 participants into the cohort. Main outcome measures Basic reproduction number R0, serial interval of accepting the challenge, and odds ratios of associated risk factors based on fully observed nomination chains; R0 is a measure of transmissibility and is defined as the number of secondary cases generated by a single index in a fully susceptible population. Serial interval is the duration between onset of a primary case and onset of its secondary cases. Results Based on the empirical data and assuming a branching process we estimated a mean R0 of 1.43 (95% confidence interval 1.23 to 1.65) and a mean serial interval for accepting the challenge of 2.1 days (median 1 day). Higher log (base 10) net worth of the participants was positively associated with transmission (odds ratio 1.63, 95% confidence interval 1.06 to 2.50), adjusting for age and sex. Conclusions The Ice Bucket Challenge was moderately transmissible among a group of globally influential celebrities, in the range of the pandemic A/H1N1 2009 influenza. The challenge was more likely to be spread by richer celebrities, perhaps in part reflecting greater social influence. PMID:25514905

  13. Large Aperture "Photon Bucket" Optical Receiver Performance in High Background Environments

    Science.gov (United States)

    Vilnrotter, Victor A.; Hoppe, D.

    2011-01-01

    The potential development of large aperture groundbased "photon bucket" optical receivers for deep space communications, with acceptable performance even when pointing close to the sun, is receiving considerable attention. Sunlight scattered by the atmosphere becomes significant at micron wavelengths when pointing to a few degrees from the sun, even with the narrowest bandwidth optical filters. In addition, high quality optical apertures in the 10-30 meter range are costly and difficult to build with accurate surfaces to ensure narrow fields-of-view (FOV). One approach currently under consideration is to polish the aluminum reflector panels of large 34-meter microwave antennas to high reflectance, and accept the relatively large FOV generated by state-of-the-art polished aluminum panels with rms surface accuracies on the order of a few microns, corresponding to several-hundred micro-radian FOV, hence generating centimeter-diameter focused spots at the Cassegrain focus of 34-meter antennas. Assuming pulse-position modulation (PPM) and Poisson-distributed photon-counting detection, a "polished panel" photon-bucket receiver with large FOV will collect hundreds of background photons per PPM slot, along with comparable signal photons due to its large aperture. It is demonstrated that communications performance in terms of PPM symbol-error probability in high-background high-signal environments depends more strongly on signal than on background photons, implying that large increases in background energy can be compensated by a disproportionally small increase in signal energy. This surprising result suggests that large optical apertures with relatively poor surface quality may nevertheless provide acceptable performance for deep-space optical communications, potentially enabling the construction of cost-effective hybrid RF/optical receivers in the future.

  14. The value of the absent bow tie sign in MRI of bucket-handle tears

    Energy Technology Data Exchange (ETDEWEB)

    Watt, Andrew J.B.; Halliday, Tonya; Raby, Nigel

    2000-08-01

    AIM: To assess the accuracy of the absent bow tie sign in diagnosing bucket handle meniscal tears (BHT) of the knee menisci. MATERIALS AND METHODS: During a 3-year period, we correlated the MRI and arthroscopic findings and the presence of the various signs. One hundred and seven knees were reviewed: 74 where either MRI or arthroscopy had identified a BHT and 33 which were either normal (31), or a simple tear was identified (2). All cases were reviewed by a single radiologist with a musculoskeletal interest blinded to the original results. Each was assessed for the presence of (1) a central meniscal fragment, (2) the double posterior cruciate ligament (PCL) sign, (3) the bow tie sign and (4) the contribution of a 3D-volume sequence. RESULTS: Optimal results were obtained using standard sequences and a 3D-volume sequence, giving a sensitivity of 74% and positive predictive value of 89%. The bow tie sign gave a sensitivity of 71% and positive predictive value of 76%, significantly less than previous reports. The 18 BHTs diagnosed by arthroscopy but missed by MRI showed other abnormal findings at MRI and were not reported as normal. CONCLUSION: We were not able to reproduce the previously reported high sensitivity and specificity of the absent bow tie sign. Despite optimization of all factors, the accurate diagnosis of a bucket handle tear remains difficult, and is most reliably made by identifying a central meniscal fragment, rather than relying on secondary signs such as the absent bow tie sign. Watt, A.J.B. (2000)

  15. Scientific Basis for Paint Stripping: Elucidated Combinatorial Mechanism of Methylene Chloride and Phenol Based Paint Removers

    Science.gov (United States)

    2013-10-10

    Electron Microscope SERDP - Strategic Environmental Research and Development Program Tg – Glass Transition TGA – Thermal Gravimetric Analysis UV... analysis , visible microscopy and spectroscopy and vibrational spectroscopy to understand the mechanism of how methylene chloride based paint removers...allowed for analysis of the different components of methylene chloride based paint strippers. Methocel is the trade name of hydroxypropyl

  16. Best lighting for visual appreciation of artistic paintings--experiments with real paintings and real illumination.

    Science.gov (United States)

    Nascimento, Sérgio Miguel Cardoso; Masuda, Osamu

    2014-04-01

    In a previous study based on monitor simulations of artistic paintings, it was found that the average correlated color temperature (CCT) of daylight preferred by a large set of observers to illuminate paintings was around 5100 K. The goal of the present study was to test if this result holds in real viewing conditions, i.e., with real paintings and real light sources. The same 11 paintings were tested in real conditions illuminated by a spectrally tunable light source and with accurate monitor simulations. To ensure uniform illumination across the paintings, only a central part of the paintings was visible to the observers. It was found that the average CCT preferred for real and monitor viewing conditions were very similar, 5500 and 5700 K, respectively. The somewhat larger CCT obtained with monitor viewing in relation to the former study was only observed in some paintings and was attributed to the smaller viewing area. These results confirm that CCT for best appreciation of paintings is higher than normally used in museums, and the viewing conditions, real or simulated, have only a minor effect.

  17. A ‘painted chamber’ in Beverwijk by Jacobus Luberti Augustini: novel insights into the working methods and painting practices in a painted wall-hanging factory

    NARCIS (Netherlands)

    Verslype, I.; Verhave, J.; Smelt, S.; Keune, K.; Sigmond, H.; van Eikema Hommes, M.; Evans, H.; Muir, K.

    2015-01-01

    The restoration of the ‘painted chamber’ in Beverwijk by Jacobus Luberti Augustini instigated an in-depth technical study of the room and its painted canvas wall hangings. Through close observation with the naked eye, ultraviolet light, infrared reflectography and the study of paint samples in combi

  18. A ‘painted chamber’ in Beverwijk by Jacobus Luberti Augustini: novel insights into the working methods and painting practices in a painted wall-hanging factory

    NARCIS (Netherlands)

    Verslype, I.; Verhave, J.; Smelt, S.; Keune, K.; Sigmond, H.; van Eikema Hommes, M.; Evans, H.; Muir, K.

    2015-01-01

    The restoration of the ‘painted chamber’ in Beverwijk by Jacobus Luberti Augustini instigated an in-depth technical study of the room and its painted canvas wall hangings. Through close observation with the naked eye, ultraviolet light, infrared reflectography and the study of paint samples in

  19. Laser cleaning treatment of burnt paintings

    Science.gov (United States)

    Antonopoulou-Athera, N.; Chatzitheodoridis, E.; Doulgerides, M.; Evangelatos, Ch.; Serafetinides, A. A.; Terlixi, A.

    2015-01-01

    Three samples taken from two paintings partly burned by fire are investigated for cleaning with lasers. The paintings belong to the collection of the National Gallery of Athens and were made by the great Greek artist Konstantinos Parthenis. To remove the damaged surface and achieve an acceptable restoration result, the optimum combination of fluence and wavelength are sought. Seven different wavelengths with a set of fluences where used, i.e., the five harmonics of a Nd:YAG laser (1064, 532, 355, 266, and 213 nm), a TEA 10.6 μm CO2 and a free running laser Er:YAG 2.94 μm. Characterization was performed prior and after the cleaning process by optical and electron microscopy and analysis (SEM/BSE EDS), as well as X-Ray Diffraction (XRD). The results of this work indicate that the wavelength in the visible spectrum (532 nm) with fluences between 0.1-0.4J/cm2 show the optimum cleaning. The optical microscopy observation shows that with these laser parameters the burnt layer was preferentially removed, exposing the original colors that Parthenis had used in these paintings. Electron microscopy imaging and chemical analysis revealed that the original texture and materials of these samples are preserved after irradiation. Since the damage varies along the surface of the painting, more experiments should be performed in order to find and optimize the full cleaning and characterization process for the homogeneous cleaning of the whole surface of the painting.

  20. Effects of plasticizers and their mixtures on estrogen Receptor and thyroid hormone functions

    DEFF Research Database (Denmark)

    Ghisari, Mandana; Bonefeld-Jørgensen, Eva Cecilie

    2009-01-01

    Plasticizers are additives used to increase the flexibility or plasticity of the material to which they are added, normally rigid plastic and as additives in paint and adhesives. They are suspected to interfere with the endocrine system, including the estrogen and the thyroid hormone (TH) systems...... was lower than predicted, suggesting a potential antagonizing effect of the mixture. In conclusion, the tested plasticizers and phenols elicited endocrine-disrupting potential that can be mediated via interference with the estrogen and TH systems. Moreover, the observed mixture effect stresses...

  1. Temperature profile data from bucket, surface seawater intake, and XBT casts in a world wide distribution from 07 December 1995 to 18 October 1996 (NODC Accession 9600167)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using bucket, surface seawater intake, and XBT casts from several vessels in a world wide distribution from December 07, 1995...

  2. Temperature and wind speed data from XBT and bucket casts from the R/V OCEANOGRAPHER AND R/V RESEARCHER I (NODC Accession 7700678)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Air temperature, water temperature, and wind speed data were collected using XBT and bucket casts from the R/V OCEANGRAPHER AND R/V RESEARCHER I.

  3. Paint indusry and environmental problem. Toryo kogyo to kankyo mondai

    Energy Technology Data Exchange (ETDEWEB)

    Osawa, A. (Nippon Oil and Fats Co., Tokyo (Japan))

    1991-10-11

    Relating to the paint industry, introduction was made of environmental problem, particularly trend of the hydrocarbonexhaust regulation, and problem against the global warming gas and acid rain. Environmental pollution matter produced by the paint industry and painting industry being mainly hybrocarbon (organic solvent), the worldwide quantity of hydrocabon exhausted in the atmosphere is estimated to be annually 20 million tons, of which 18%, i.e., an annual quantity of 3.5 million tons is exhausted from the field of paint industry. The role to be played by the paint industry is important for the lowering in pollution by the hydrocarbon. Useful paints for the environmental maintenance comprise high solid paint, aqueous paint, slurry paint, powder paint and UV-hardened paint. The automobile coating is being also changed from the metallic coating to the aqueous coating. Low temperature hardening paint is used for the countermeasures against the global warming gas. For those against the acid rain, urethane hardening, hardening by the acid-epoxy group reaction, hardening by the alkoxyl froup reaction and other hardenings are developed to replace the conventional hardening by the melamine resin for heightening in acidproofness of paint film. 5 ref., 1 fig., 3 tabs.

  4. Preference for and discrimination of paintings by mice.

    Science.gov (United States)

    Watanabe, Shigeru

    2013-01-01

    I measured preference for paintings (Renoir vs. Picasso or Kandinsky vs. Mondrian) in mice. In general mice did not display a painting preference except for two mice: one preferred Renoir to Picasso, and the other preferred Kandinsky to Mondrian. Thereafter, I examined discrimination of paintings with new mice. When exposure to paintings of one artist was associated with an injection of morphine (3.0 mg/kg), mice displayed conditioned preference for those paintings, showing discrimination of paintings by Renoir from those by Picasso, and paintings by Kandinsky from those by Mondrian after the conditioning. They also exhibited generalization of the preference to novel paintings of the artists. After conditioning with morphine for a set of paintings consisting of two artists, mice showed discrimination between two sets of paintings also from the two artists but not in association with morphine. These results suggest that mice can discriminate not only between an artist's style but also among paintings of the same artist. When mice were trained to discriminate a pair of paintings by Kandinsky and Renoir in an operant chamber equipped with a touch screen, they showed transfer of the discrimination to new pairs of the artists, but did not show transfer of discrimination of paintings by other artists, suggesting generalization.

  5. Preference for and discrimination of paintings by mice.

    Directory of Open Access Journals (Sweden)

    Shigeru Watanabe

    Full Text Available I measured preference for paintings (Renoir vs. Picasso or Kandinsky vs. Mondrian in mice. In general mice did not display a painting preference except for two mice: one preferred Renoir to Picasso, and the other preferred Kandinsky to Mondrian. Thereafter, I examined discrimination of paintings with new mice. When exposure to paintings of one artist was associated with an injection of morphine (3.0 mg/kg, mice displayed conditioned preference for those paintings, showing discrimination of paintings by Renoir from those by Picasso, and paintings by Kandinsky from those by Mondrian after the conditioning. They also exhibited generalization of the preference to novel paintings of the artists. After conditioning with morphine for a set of paintings consisting of two artists, mice showed discrimination between two sets of paintings also from the two artists but not in association with morphine. These results suggest that mice can discriminate not only between an artist's style but also among paintings of the same artist. When mice were trained to discriminate a pair of paintings by Kandinsky and Renoir in an operant chamber equipped with a touch screen, they showed transfer of the discrimination to new pairs of the artists, but did not show transfer of discrimination of paintings by other artists, suggesting generalization.

  6. Methylisothiazolinone and benzisothiazolinone are widely used in paint: a multicentre study of paints from five European countries

    DEFF Research Database (Denmark)

    Schwensen, Jakob F; Lundov, Michael; Bossi, Rossana

    2015-01-01

    were found in paints from all five countries. Paints purchased in Denmark and Sweden contained especially high concentrations of BIT. CONCLUSION: The use of MI across European countries is extensive. In view of the ongoing epidemic of MI contact allergy, an evaluation of the safety of MI in paints...... of MI, methylchloroisothiazolinone (MCI) and benzisothiazolinone (BIT) in paints on the European retail market. METHODS: Wall paints (n = 71) were randomly purchased in retail outlets in five European countries. The paints were quantitatively analysed for their contents of MI, MCI and BIT by high...

  7. The Actinobacterial Colonization of Etruscan Paintings

    Science.gov (United States)

    Diaz-Herraiz, Marta; Jurado, Valme; Cuezva, Soledad; Laiz, Leonila; Pallecchi, Pasquino; Tiano, Piero; Sanchez-Moral, Sergio; Saiz-Jimenez, Cesareo

    2013-01-01

    The paintings from Tomba della Scimmia, in Tuscany, are representative of the heavy bacterial colonization experienced in most Etruscan necropolises. The tomb remained open until the late 70′s when it was closed because of severe deterioration of the walls, ceiling and paintings after decades of visits. The deterioration is the result of environmental changes and impacts suffered since its discovery in 1846. We show scanning electron microscopy and molecular studies that reveal the extent and nature of the biodeterioration. Actinobacteria, mainly Nocardia and Pseudonocardia colonize and grow on the tomb walls and this process is linked to the availability of organic matter, phyllosilicates (e.g. clay minerals) and iron oxides. Nocardia is found metabolically active in the paintings. The data confirm the specialization of the genera Nocardia and Pseudonocardia in the colonization of subterranean niches. PMID:23486535

  8. Focal cerebral lesions and painting abilities.

    Science.gov (United States)

    Mazzucchi, Anna; Sinforiani, Elena; Boller, François

    2013-01-01

    Focal lesions such as strokes significantly affect painting production in the vast majority of artists. In particular, painters, when they resume painting, show changes in their painting style. In exceptional cases, there may be an apparent improvement in style, but in most cases, the changes represent nothing short of deterioration. This, however, varies according to the hemisphere affected. Painters with left-hemisphere lesions tend to show an inability to deal adequately with perspective and also tend to use simplified colors with fewer nuances. One often witnesses an evolution toward simpler, often "naïve" techniques, and at times rigid geometric repetitive features. Painters with right-hemisphere lesions also become unable to represent tridimensionality. In addition, their figures are often drawn in very summary fashion, with lack of coordination between volumes and space and a chromatic impoverishment; their main problem, however, is visuospatial, leading to neglect of the left side of the canvas.

  9. Visual comparison testing of automotive paint simulation

    Science.gov (United States)

    Meyer, Gary; Fan, Hua-Tzu; Seubert, Christopher; Evey, Curtis; Meseth, Jan; Schnackenberg, Ryan

    2015-03-01

    An experiment was performed to determine whether typical industrial automotive color paint comparisons made using real physical samples could also be carried out using a digital simulation displayed on a calibrated color television monitor. A special light booth, designed to facilitate evaluation of the car paint color with reflectance angle, was employed in both the real and virtual color comparisons. Paint samples were measured using a multi-angle spectrophotometer and were simulated using a commercially available software package. Subjects performed the test quicker using the computer graphic simulation, and results indicate that there is only a small difference between the decisions made using the light booth and the computer monitor. This outcome demonstrates the potential of employing simulations to replace some of the time consuming work with real physical samples that still characterizes material appearance work in industry.

  10. Perceptual dimensions of style in paintings

    Directory of Open Access Journals (Sweden)

    Marković Slobodan

    2007-01-01

    Full Text Available The main purpose of this study is to specify the basic perceptual dimensions underlying the judgments of the physical features which define the style in paintings (e.g. salient form, colorful surface, oval contours etc.. The other aim of the study is to correlate these dimensions with the subjective (affective dimensions of the experience of paintings. In the preliminary study a set of 25 pairs of elementary perceptual descriptors were empirically specified, and a set of 25 bipolar scales were made (e.g. uncolored-multicolored. In the experiment 30 subjects judged 24 paintings (paintings were taken from the study of Radonjić and Marković, 2004 on 25 scales. Factor analysis revealed the four factors: form (scales: precise, neat, salient form etc., color (color contrast, lightness contrast, vivid colors, space (voluminosity, depth and oval contours and complexity (multicolored, ornate, detailed. Obtained factors reflected the nature of the phenomenological and neural segregation of form, color, depth processing, and partially of complexity processing (e.g. spatial frequency processing within both the form and color subsystem. The aim of the next step of analysis was to specify the correlations between two groups of judgments: (a mean judgments of 24 paintings on perceptual factors and (b mean judgments of the same set of 24 paintings on subjective (affective experience factors, i.e. regularity, attraction, arousal and relaxation (judgments taken from Radonjić and Marković, 2005. The following significant correlations were obtained: regularity-form, regularity-space, attraction-form and arousal-complexity (negative correlation. The reasons for the unexpected negative correlation between arousal and complexity should be specified in further studies.

  11. Overcoming maladaptive plasticity through plastic compensation

    Directory of Open Access Journals (Sweden)

    Matthew R.J. MORRIS, Sean M. ROGERS

    2013-08-01

    Full Text Available Most species evolve within fluctuating environments, and have developed adaptations to meet the challenges posed by environmental heterogeneity. One such adaptation is phenotypic plasticity, or the ability of a single genotype to produce multiple environmentally-induced phenotypes. Yet, not all plasticity is adaptive. Despite the renewed interest in adaptive phenotypic plasticity and its consequences for evolution, much less is known about maladaptive plasticity. However, maladaptive plasticity is likely an important driver of phenotypic similarity among populations living in different environments. This paper traces four strategies for overcoming maladaptive plasticity that result in phenotypic similarity, two of which involve genetic changes (standing genetic variation, genetic compensation and two of which do not (standing epigenetic variation, plastic compensation. Plastic compensation is defined as adaptive plasticity overcoming maladaptive plasticity. In particular, plastic compensation may increase the likelihood of genetic compensation by facilitating population persistence. We provide key terms to disentangle these aspects of phenotypic plasticity and introduce examples to reinforce the potential importance of plastic compensation for understanding evolutionary change [Current Zoology 59 (4: 526–536, 2013].

  12. Overcoming maladaptive plasticity through plastic compensation

    Institute of Scientific and Technical Information of China (English)

    Matthew R.J.MORRIS; Sean M.ROGERS

    2013-01-01

    Most species evolve within fluctuating environments,and have developed adaptations to meet the challenges posed by environmental heterogeneity.One such adaptation is phenotypic plasticity,or the ability of a single genotype to produce multiple environmentally-induced phenotypes.Yet,not all plasticity is adaptive.Despite the renewed interest in adaptive phenotypic plasticity and its consequences for evolution,much less is known about maladaptive plasticity.However,maladaptive plasticity is likely an important driver of phenotypic similarity among populations living in different environments.This paper traces four strategies for overcoming maladaptive plasticity that result in phenotypic similarity,two of which involve genetic changes (standing genetic variation,genetic compensation) and two of which do not (standing epigenetic variation,plastic compensation).Plastic compensation is defined as adaptive plasticity overcoming maladaptive plasticity.In particular,plastic compensation may increase the likelihood of genetic compensation by facilitating population persistence.We provide key terms to disentangle these aspects of phenotypic plasticity and introduce examples to reinforce the potential importance of plastic compensation for understanding evolutionary change.

  13. Breast Mass in a Rubens Painting

    Directory of Open Access Journals (Sweden)

    Davide Lazzeri

    2016-04-01

    Full Text Available Deformity of the breast and axilla observed in famous paintings is a fascinating field for the medico-artists. The attempt of a retrospective diagnosis of breast tumors is highly challenging. This paper deals with a Rubens painting portraying the heroine Judith with a visible but previously unreported left breast mass. Though speculative, the present medico-artistic diagnosis is of a tumor likely to be of benign nature. It is of interest that the present case is the sixth breast disease discovered in Rubens’s works.

  14. Breast Mass in a Rubens Painting.

    Science.gov (United States)

    Lazzeri, Davide; Lippi, Donatella; Castello, Manuel Francisco; Weisz, George M

    2016-04-19

    Deformity of the breast and axilla observed in famous paintings is a fascinating field for the medico-artists. The attempt of a retrospective diagnosis of breast tumors is highly challenging. This paper deals with a Rubens painting portraying the heroine Judith with a visible but previously unreported left breast mass. Though speculative, the present medico-artistic diagnosis is of a tumor likely to be of benign nature. It is of interest that the present case is the sixth breast disease discovered in Rubens's works.

  15. Painting the Soul of the Yangtze River

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Chen Kezhi:a prestigious oil painter and a household name in Chinese fine arts circles,is add- ing luster to the cultural prosperity of the country with his artistic efforts.The latest sensation is over his masterpieces of the Three Gorges area.Since 1996,he has devoted himself to the Three Gorges series.These paintings reproduce the original impression of the Three Gorges area that will never be seen again.The paintings deliver the mystic atmosphere of the orient and the majestic scenery of China.Chen recently sat down with Beijing Review reporter Huang Jun to share his views and experience on these masterpieces.

  16. BICARBONATE OF SODA BLASTING TECHNOLOGY FOR AIRCRAFT WHEEL PAINTING

    Science.gov (United States)

    This evaluation addressed product quality, waste reduction/pollution prevention and economics in replacing chemical solvent strippers with a bicarbonate of soda blasting technology for removal of paint from aircraft wheels. The evaluation was conducted in the Paint Stripping Sho...

  17. Parameterization of a bucket model for soil-vegetation-atmosphere modeling under seasonal climatic regimes

    Directory of Open Access Journals (Sweden)

    N. Romano

    2011-12-01

    Full Text Available We investigate the potential impact of accounting for seasonal variations in the climatic forcing and using different methods to parameterize the soil water content at field capacity on the water balance components computed by a bucket model (BM. The single-layer BM of Guswa et al. (2002 is employed, whereas the Richards equation (RE based Soil Water Atmosphere Plant (SWAP model is used as a benchmark model. The results are analyzed for two differently-textured soils and for some synthetic runs under real-like seasonal weather conditions, using stochastically-generated daily rainfall data for a period of 100 years. Since transient soil-moisture dynamics and climatic seasonality play a key role in certain zones of the World, such as in Mediterranean land areas, a specific feature of this study is to test the prediction capability of the bucket model under a condition where seasonal variations in rainfall are not in phase with the variations in plant transpiration. Reference is made to a hydrologic year in which we have a rainy period (starting 1 November and lasting 151 days where vegetation is basically assumed in a dormant stage, followed by a drier and rainless period with a vegetation regrowth phase. Better agreement between BM and RE-SWAP intercomparison results are obtained when BM is parameterized by a field capacity value determined through the drainage method proposed by Romano and Santini (2002. Depending on the vegetation regrowth or dormant seasons, rainfall variability within a season results in transpiration regimes and soil moisture fluctuations with distinctive features. During the vegetation regrowth season, transpiration exerts a key control on soil water budget with respect to rainfall. During the dormant season of vegetation, the precipitation regime becomes an important climate forcing. Simulations also highlight the occurrence of bimodality in the probability distribution of soil moisture during the season when plants are

  18. [The "Ice Bucket Challenge": wondering about the impact of social networks to promote public health interventions].

    Science.gov (United States)

    Gualano, Maria Rosaria; Bert, Fabrizio; Gili, Renata; Andriolo, Violetta; Scaioli, Giacomo; Siliquini, Roberta

    2015-01-01

    The "Ice Bucket Challenge" was an activity launched to promote awareness of amyotrophic lateral sclerosis (ALS) and encourage donations to research for this disease. The campaign went viral on social media during July to August 2014. It consisted in nominating people and challenging them to donate 100 dollars to the ALS Association or pour a bucket of ice water over their head and post the video on the web. Participants in turn then had to challenge others to do the same. The initiative was hugely successful, involved millions of people and, just in the US, collected 35 times more money than in the same time period in 2013. We analyzed possible factors that determined the success of this initiative, to identify strengths and weaknesses of the activity and evaluate the possibility of applying the same model to promote public health interventions. Several features of the challenge were identified as strengths: the involvement of wellknown people from different contexts, the "public platform" which triggers a positive combination of competitiveness, social pressure and narcissism, the chain-letter like method of nomination, the ironic and entertaining nature of the performance. Besides these strengths, weaknesses were also identified: information spread via social media can only partially reach potential donors and supporters, due to the digital divide phenomenon which excludes people who do not have web access. Also, it is not possible to predict if the message will be long-lasting or will cease shortly after the end of the campaign. The latter could be acceptable for fund-raising, where the aim is simply to collect as much money as possible, but not for a public health intervention program, whose success requires that the intended message has a long-lasting effect to produce an effective change in people's behavior. Despite the above-mentioned limits, social networks undeniably show great potential to spread messages to the community and to involve a large number of

  19. The bucket and the searchlight: formulating and testing risk hypotheses about the weediness and invasiveness potential of transgenic crops.

    Science.gov (United States)

    Raybould, Alan

    2010-01-01

    The bucket and the searchlight are metaphors for opposing theories of the growth of scientific knowledge. The bucket theory proposes that knowledge is gained by observing the world without preconceptions, and that knowledge emerges from the accumulation of observations that support a hypothesis. There are many problems with this theory, the most serious of which is that it does not appear to offer a means to distinguish between the many hypotheses that could explain a particular set of observations. The searchlight theory proposes that preconceptions are unavoidable and that knowledge advances through the improvement of our preconceptions - our hypotheses - by continuous criticism and revision. A hypothesis is a searchlight that illuminates observations that test the hypothesis and reveal its flaws, and knowledge thereby increases through the elimination of false hypotheses. Research into the risks posed by the cultivation of transgenic crops often appears to apply the bucket theory; many data are produced, but knowledge of risk is not advanced. Application of the searchlight theory, whereby risk assessments test hypotheses that transgenic crops will not be harmful, seems to offer a better way to characterise risk. The effectiveness of an environmental risk assessment should not be measured by the size of the bucket of observations on a transgenic crop, but by the power of the risk hypothesis searchlights to clarify the risks that may arise from cultivation of that crop. These points are illustrated by examples of hypotheses that could be tested to assess the risks from transgenic crops and their hybrids becoming weeds or invading non-agricultural habitats.

  20. AUTOMATED DYNAMIC LOAD CONTROL BY ELECTROMECHANICAL SYSTEMS OF A BUCKET-CHAIN EXCAVATOR IN THE COURSE OF SCOOPING

    OpenAIRE

    Khayrullin Rustam Zinnatullovich

    2012-01-01

    Methods and algorithms of control of the tension of lifting and towing ropes of bucket-chain excavators are proposed in the article. They are based on the non-linear dependence of the current path length and intensity of excavation efforts. Three automatic control modes, including scooping, correction signals and automatic overload protection, are implemented. Two independent control loops in charge of tension of lifting and towing ropes are developed. The proposed automated control syste...

  1. Pigeons' discrimination of paintings by Monet and Picasso

    OpenAIRE

    Watanabe, Shigeru; Sakamoto, Junko; Wakita, Masumi

    1995-01-01

    Pigeons successfully learned to discriminate color slides of paintings by Monet and Picasso. Following this training, they discriminated novel paintings by Monet and Picasso that had never been presented during the discrimination training. Furthermore, they showed generalization from Monet's to Cezanne's and Renoir's paintings or from Picasso's to Braque's and Matisse's paintings. These results suggest that pigeons' behavior can be controlled by complex visual stimuli in ways that suggest cat...

  2. Theoretical investigation on the dynamic behaviour of bucket wheel drives; Theoretische Untersuchungen des dynamischen Verhaltens von Schaufelradantrieben

    Energy Technology Data Exchange (ETDEWEB)

    Schlecht, B. [Krupp Foerdertechnik GmbH, Luebeck (Germany); Wuensch, D.; Christanhemmers, A. [Duisburg Univ. (Germany). Fachgebiet Konstruktionslehre und Foerdertechnik

    1999-01-01

    In the course of the continuous further development of a series of standardized bucket wheel excavators a bucket wheel drive was designed which is distinguished by a particularly high performance rating. In order to determine the dynamic stresses to be expected a simulation model for analysis of the torsional vibrations was set up. This model comprises 15 rotary bodies and, in addition to two planetary gear systems, includes a stepped bevel gear, a cardan shaft and a hydrodynamic starting coupling. The drive is effected by means of an induction machine. The simulation results show that the drive phases are effectively correlated dynamically. Unfavourable operating conditions, such as `impacts` and `blocking of bucket wheel` neither lead to undesirable excitation of resonance frequencies, nor do they cause unexpectedly high additional dynamic stresses. (orig.) [Deutsch] Im Zuge der kontinuierlichen Weiterentwicklung einer Baureihe von standardisierten Schaufelradbaggern wurde ein Schaufelradantrieb entwickelt, der sich durch eine besonders hohe Leistungsdichte auszeichnet. Zur Ermittlung der zu erwartenden dynamischen Beanspruchungen wurde ein Simulationsmodell zur Torsionsschwingungsanalyse erstellt. Das Modell umfasst 15 Drehmassen und beinhaltet neben zwei Planetengetrieben eine Kegelradstufe, eine Gelenkwelle und eine hydrodynamische Anlaufkupplung. Der Antrieb erfolgt ueber eine Asynchronmaschine. Die Ergebnisse der Simulation belegen, dass der Antriebsstrang dynamisch gut abgestimmt ist. Die unguenstigen Betriebszustaende Stoesse sowie Blockieren des Schaufelrades fuehren weder zur unerwuenschten Anregung von Resonanzfrequenzen noch bedingen sie unerwartet hohe dynamische Zusatzbeanspruchungen. (orig.)

  3. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like......, good strength and long durability. Recycling of plastic waste from production is well-established, while recycling of postconsumer plastic waste still is in its infancy. This chapter describes briefly how plastic is produced and how waste plastic is recycled in the industry. Quality requirements...

  4. Metal soaps in oil paint : Structure, mechanisms and dynamics

    NARCIS (Netherlands)

    Hermans, J.J.

    2017-01-01

    From a chemical point of view, oil paintings are not stable objects. Visually, changes in the appearance of an oil painting might be very slow, but over the course of centuries, chemical reactions and physical processes do affect the colour, texture and integrity of oil paint layers. This thesis aim

  5. Metal soaps in oil paint : Structure, mechanisms and dynamics

    NARCIS (Netherlands)

    Hermans, J.J.

    2017-01-01

    From a chemical point of view, oil paintings are not stable objects. Visually, changes in the appearance of an oil painting might be very slow, but over the course of centuries, chemical reactions and physical processes do affect the colour, texture and integrity of oil paint layers. This thesis

  6. 47 CFR 17.53 - Lighting equipment and paint.

    Science.gov (United States)

    2010-10-01

    ... Lighting equipment and paint. The lighting equipment, color or filters, and shade of paint referred to in... 47 Telecommunication 1 2010-10-01 2010-10-01 false Lighting equipment and paint. 17.53 Section 17... (Color No. 17875, FS-595). Aviation surface orange TT-P-59 1 (Color No. 12197, FS-595). Aviation...

  7. Stabilizing coal quality when developing deposits of complex structure using bucket wheel excavators

    Energy Technology Data Exchange (ETDEWEB)

    Belyakov, Yu.I.; Pushkin, S.P. (Kievskii Inzhenerno-Stroitel' nyi Institut (USSR))

    1989-07-01

    Using the example of the complex geological conditions found in the Ehkibastuz basin, describes a method of computerized simulation that may be used to forecast the ash content of coal. This method may be applied to vertical and horizontal coal extraction and takes into account the excavator's technical parameters, the load carrying capacity of the rail wagons used to transport the coal, the geological condition of the seam layers, and the type of bucket wheel excavator used. Based on the results of investigation into variations in ash content, claims that the coefficient of variation in the ash content of coal transported by rail wagons to electric power plants may be reduced by selecting technology according to the seam's angle of dip. Recommends that excavators with a wheel diameter of 10-13 m (e.g. the SPs(k)-2000 or EhRShRD-5000) be used on angles of dip of 0-50 degrees and excavators with a wheel diameter of 6-7 m (e.g. the EhRP-1250) be used on angles of dip of 50-90 degrees. Replacing the EhRP-1250 by the ERShRD-5000 in the Bogatyr' coal mine would reduce the coefficient of ash content variation by 40%. 4 refs.

  8. Air-Floating Towing Behaviors of Multi-Bucket Foundation Platform

    Institute of Scientific and Technical Information of China (English)

    乐丛欢; 丁红岩; 张浦阳

    2013-01-01

    Air-floating towing beha viors of multi-bucket foundation plat form (MBFP) are investigated with the 1/20-scale model tests and hydrodynamic so ftware MOSES. MOSES numerical model was val idated by test results, and M OSES prototype model of MBFP can eliminate scale effect of model. The influences of towing factors of to wing speed, water depth, freeboard, and w ave direction on air-floating tow ing stability of MBFP were analyzed by model tests and validated MOSES prototype mod el. It is sho wn that the re duction of towing sp eed can effectively d ecrease the to wing force and surge acceleration to improve towing stability. Water depth is another f actor in towing s tability. Obvious shallow water effect will appear in shallow water with sma ll water depth-draft ratio and it w ill disappear gradually and air-floating towing becomes more stable with the increase of water depth. Accelerations of surge, s way and heave are small and they have modest changes when freeboard increases from 0.5 to 2 m. For MBFP, the freeboard is not suggested to be larger than 2 m in following wave. Wave direction has large influence on the towing stability, the surge acceleration and towing force are sensitive to the va riation of wave direction, the surge acceleration and towing force in following wave (0°) and counter wave (180°) are much larger than that in transverse sea (90°and 270°).

  9. ROBUSTNESS OF MORPHOGEN GRADIENTS WITH "BUCKET BRIGADE" TRANSPORT THROUGH MEMBRANE-ASSOCIATED NON-RECEPTORS.

    Science.gov (United States)

    Lei, Jinzhi; Wang, Dongyong; Song, You; Nie, Qing; Wan, Frederic Y M

    2013-05-01

    Robust multiple-fate morphogen gradients are essential for embryo development. Here, we analyze mathematically a model of morphogen gradient (such as Dpp in Drosophila wing imaginal disc) formation in the presence of non-receptors with both diffusion of free morphogens and the movement of morphogens bound to non-receptors. Under the assumption of rapid degradation of unbound morphogen, we introduce a method of functional boundary value problem and prove the existence, uniqueness and linear stability of a biologically acceptable steady-state solution. Next, we investigate the robustness of this steady-state solution with respect to significant changes in the morphogen synthesis rate. We prove that the model is able to produce robust biological morphogen gradients when production and degradation rates of morphogens are large enough and non-receptors are abundant. Our results provide mathematical and biological insight to a mechanism of achieving stable robust long distance morphogen gradients. Key elements of this mechanism are rapid turnover of morphogen to non-receptors of neighoring cells resulting in significant degradation and transport of non-receptor-morphogen complexes, the latter moving downstream through a "bucket brigade" process.

  10. Failure-probability driven dose painting

    DEFF Research Database (Denmark)

    Vogelius, Ivan R; Håkansson, Katrin; Due, Anne K;

    2013-01-01

    To demonstrate a data-driven dose-painting strategy based on the spatial distribution of recurrences in previously treated patients. The result is a quantitative way to define a dose prescription function, optimizing the predicted local control at constant treatment intensity. A dose planning stu...

  11. Radiocarbon dating of ancient rock paintings

    Energy Technology Data Exchange (ETDEWEB)

    Ilger, W.A.; Hyman, M.; Rowe, M.W. [Texas A and M Univ., College Station, TX (United States). Dept. of Chemistry; Southon, J. [Lawrence Livermore National Lab., CA (United States)

    1995-06-20

    This report presents progress made on a technique for {sup 14}C dating pictographs. A low-temperature oxygen plasma is used coupled with high-vacuum technologies to selectively remove C-containing material in the paints without contamination from inorganic carbon from rock substrates or accretions.

  12. Computer simulation of backscattering spectra from paint

    Science.gov (United States)

    Mayer, M.; Silva, T. F.

    2017-09-01

    To study the role of lateral non-homogeneity on backscattering analysis of paintings, a simplified model of paint consisting of randomly distributed spherical pigment particles embedded in oil/binder has been developed. Backscattering spectra for lead white pigment particles in linseed oil have been calculated for 3 MeV H+ at a scattering angle of 165° for pigment volume concentrations ranging from 30 vol.% to 70 vol.% using the program STRUCTNRA. For identical pigment volume concentrations the heights and shapes of the backscattering spectra depend on the diameter of the pigment particles: This is a structural ambiguity for identical mean atomic concentrations but different lateral arrangement of materials. Only for very small pigment particles the resulting spectra are close to spectra calculated supposing atomic mixing and assuming identical concentrations of all elements. Generally, a good fit can be achieved when evaluating spectra from structured materials assuming atomic mixing of all elements and laterally homogeneous depth distributions. However, the derived depth profiles are inaccurate by a factor of up to 3. The depth range affected by this structural ambiguity ranges from the surface to a depth of roughly 0.5-1 pigment particle diameters. Accurate quantitative evaluation of backscattering spectra from paintings therefore requires taking the correct microstructure of the paint layer into account.

  13. Radiocarbon dating of ancient rock paintings.

    Science.gov (United States)

    Rowe, Marvin W

    2009-03-01

    A technique based on cold argon and oxygen plasmas permits radiocarbon dates to be obtained on paintings that contain inorganic pigments. (To listen to a podcast about this feature, please go to the Analytical Chemistry website at http://pubs.acs.org/journal/ancham.).

  14. The Ancient Art of Silk Painting

    Science.gov (United States)

    Yonker, Kim

    2010-01-01

    In this article, the author describes a silk-painting project with a sea-creature theme for eighth-grade students. Other themes can be used such as geometric quilt designs, tropical rain forest, large flowers, Art Nouveau motifs, portraits and more. (Contains 2 resources.)

  15. Understanding Korean food culture from Korean paintings

    Directory of Open Access Journals (Sweden)

    Hae Kyung Chung

    2016-03-01

    Conclusion: Beyond the basic value of food in maximizing nutrients and energy, Korean food culture has developed distinctive cultural characteristics through more than 5,000 years of agricultural history. Although the genre paintings analyzed in this paper are limited to a certain era, this paper will serve as a milestone in providing direction for future studies.

  16. The Beauty of Painting in English Writing

    Institute of Scientific and Technical Information of China (English)

    郝艳慧

    2016-01-01

    English writing ability is emphasized in English teaching without any doubt. And this article attempts to reexamine the teaching of writing and explain the nature of writing from an aesthetic perspective-its beauty of painting. Hope either teachers or students could make a deep aesthetic understanding of English writing from this article.

  17. Rendering Visible: Painting and Sexuate Subjectivity

    Science.gov (United States)

    Daley, Linda

    2015-01-01

    In this essay, I examine Luce Irigaray's aesthetic of sexual difference, which she develops by extrapolating from Paul Klee's idea that the role of painting is to render the non-visible rather than represent the visible. This idea is the premise of her analyses of phenomenology and psychoanalysis and their respective contributions to understanding…

  18. Early Netherlandish Paintings : Rediscovery, Reception and Research

    NARCIS (Netherlands)

    Ridderbos, Bernhard; Buren, van Anne; Veen, van Henk

    2004-01-01

    The so-called Flemish Primitives, a group of 15th-century painters from the Southern Netherlands, acquired their name in the 19th century. Among them were the world-famous artists such as Rogier van der Weyden, Hans Memling, the brothers Van Eyck, and Hugo van der Goes. Their masterpieces, oil paint

  19. Painting: Is It Indigenous to Ghanaian Culture?

    Directory of Open Access Journals (Sweden)

    Emmanuel Antwi

    2014-10-01

    Full Text Available Painting could be said to be well grounded in all cultures worldwide. This is underpinned by the vast record of cave art as globally represented, even though this phenomenon does not seamlessly continue into some ancient traditions that followed. In the face of the above however, to find the traditional period of a people one has to identify the geographical area of this group in order to consider the autochthonous art practice of the place so as to determine its cultural beginnings, extent, and forms of art explored. In the case of Ghana, one observes that, art historians usually site the beginning of painting at the time when colonial educational training of the arts was begun in Achimota from the 1900s. The study was conducted using historical review and analysis, unstructured interview guides as well as participant and non-participant observational techniques in a descriptive design at Sirigu, Ahwiaa and Ntonso, revealing the forms of painting that existed in the country before the introduction of formal training by the colonial masters. The result showed that Ghanaians traditionally practiced different kinds of painting, long before the colonial art training programme was introduced. We feel it should be of concern for any people to be able to tell, not only how, and why but also when they started doing the things that matter to their existence and cultural heritage.

  20. Piezoelectric paint sensor for ultrasonic NDE

    Science.gov (United States)

    Li, X.; Zhang, Y.

    2007-04-01

    This paper deals with a distributed acoustic emission sensing method, which is especially suitable for piezoelectric paint. Piezoelectric paint is a composite piezoelectric material that is comprised of tiny piezoelectric particles randomly dispersed within a polymer matrix phase. An overview of the distributed acoustic emission sensing method for defect monitoring is given in this paper. The use of piezoelectric materials for ultrasonic signal measurements is next discussed along with a series of ultrasonic tests performed to verify the ultrasonic sensing capability of piezoelectric paint. To examine the mechanism of the distributed acoustic emission sensing method for crack initiation detection, the results of a finite element simulation based study is presented in this paper. The finite element model used in the parametric study is calibrated with experimental data. The effect of sensor numbers included in the array has been studied using both simulation and experimental data. Based on the preliminary results of this study, piezoelectric paint sensor appears to hold a potential for use in on-line monitoring of cracks such as those caused by fatigue in metal structures although more work is still needed before successful practical application can be made.

  1. Soap bubbles in paintings: Art and science

    Science.gov (United States)

    Behroozi, F.

    2008-12-01

    Soap bubbles became popular in 17th century paintings and prints primarily as a metaphor for the impermanence and fragility of life. The Dancing Couple (1663) by the Dutch painter Jan Steen is a good example which, among many other symbols, shows a young boy blowing soap bubbles. In the 18th century the French painter Jean-Simeon Chardin used soap bubbles not only as metaphor but also to express a sense of play and wonder. In his most famous painting, Soap Bubbles (1733/1734) a translucent and quavering soap bubble takes center stage. Chardin's contemporary Charles Van Loo painted his Soap Bubbles (1764) after seeing Chardin's work. In both paintings the soap bubbles have a hint of color and show two bright reflection spots. We discuss the physics involved and explain how keenly the painters have observed the interaction of light and soap bubbles. We show that the two reflection spots on the soap bubbles are images of the light source, one real and one virtual, formed by the curved surface of the bubble. The faint colors are due to thin film interference effects.

  2. Simulations of color development in tinted paints

    NARCIS (Netherlands)

    Stuiver, A.; Barkema, G.T.

    2010-01-01

    Monte Carlo simulations have been used to investigate how several thermodynamic and kinetic factors affect the distribution of pigments, when a water-based pigment dispersion is added to a solvent-borne paint. Our model contains three types of lattice particles: water, pigment and organic solvent, w

  3. Integrate Art! Match Poetry to Painting.

    Science.gov (United States)

    Parks, Mary

    1994-01-01

    It is possible to connect art and language arts using traditional Japanese art. After explaining the Japanese art forms of Haiku poetry and sumi-e painting, the article describes a project in which students write haiku on special paper then illustrate their poems with gung and shey strokes. (SM)

  4. Nabokov and the Art of Painting

    NARCIS (Netherlands)

    Vries, de Gerard J.M.; Johnson, D. Barton

    2005-01-01

    Vladimir Nabokov was one of the greatest novelists of the previous century and his mastery of English and Russian prose is unequalled. Nabokov had originally trained to become a painter and shared Marc Chagall's tutor in Paris. In Nabokov and the Art of Painting the authors demonstrate how the art o

  5. Nabokov and the Art of Painting

    NARCIS (Netherlands)

    Vries, de Gerard J.M.; Johnson, D. Barton

    2005-01-01

    Vladimir Nabokov was one of the greatest novelists of the previous century and his mastery of English and Russian prose is unequalled. Nabokov had originally trained to become a painter and shared Marc Chagall's tutor in Paris. In Nabokov and the Art of Painting the authors demonstrate how the art

  6. Matte painting in stereoscopic synthetic imagery

    Science.gov (United States)

    Eisenmann, Jonathan; Parent, Rick

    2010-02-01

    While there have been numerous studies concerning human perception in stereoscopic environments, rules of thumb for cinematography in stereoscopy have not yet been well-established. To that aim, we present experiments and results of subject testing in a stereoscopic environment, similar to that of a theater (i.e. large flat screen without head-tracking). In particular we wish to empirically identify thresholds at which different types of backgrounds, referred to in the computer animation industry as matte paintings, can be used while still maintaining the illusion of seamless perspective and depth for a particular scene and camera shot. In monoscopic synthetic imagery, any type of matte painting that maintains proper perspective lines, depth cues, and coherent lighting and textures saves in production costs while still maintaining the illusion of an alternate cinematic reality. However, in stereoscopic synthetic imagery, a 2D matte painting that worked in monoscopy may fail to provide the intended illusion of depth because the viewer has added depth information provided by stereopsis. We intend to observe two stereoscopic perceptual thresholds in this study which will provide practical guidelines indicating when to use each of three types of matte paintings. We ran subject tests in two virtual testing environments, each with varying conditions. Data were collected showing how the choices of the users matched the correct response, and the resulting perceptual threshold patterns are discussed below.

  7. Rendering Visible: Painting and Sexuate Subjectivity

    Science.gov (United States)

    Daley, Linda

    2015-01-01

    In this essay, I examine Luce Irigaray's aesthetic of sexual difference, which she develops by extrapolating from Paul Klee's idea that the role of painting is to render the non-visible rather than represent the visible. This idea is the premise of her analyses of phenomenology and psychoanalysis and their respective contributions to understanding…

  8. Personnel Exposure to Airborne Isocyanates and Solvents During Shipboard Painting With 2-Pack Polyurethane Paints

    Science.gov (United States)

    2008-12-01

    contain low volatility isocyanate prepolymers in addition to small quantities of volatile isocyanate monomers [2,3]. The monomers may become airborne as...vapour whilst the non-volatile prepolymers and partially cured oligomers may form aerosols during spray painting and sanding of the painted surface...JL (1992) “ Prepolymers of hexamethylene diisocyanate as a cause of occupational asthma” J. Allergy Clinical Immunol. 91 850-61. 5. Redlich CA, Bello

  9. 41 CFR 101-42.1102-7 - Lead-containing paint and items bearing lead-containing paint.

    Science.gov (United States)

    2010-07-01

    ... exempted by 16 CFR part 1303, are banned hazardous products: (i) Paint and other similar surface coating... paint may be stripped and refinished with a nonhazardous coating in lieu of destruction. Stripping shall... and the following statement: Contains Lead. Dried Film of This Paint May be Harmful If Eaten or Chewed...

  10. Evaluation of Water Resistance and Diffusion Properties of Paint Materials

    Directory of Open Access Journals (Sweden)

    J. Drchalová

    2001-01-01

    Full Text Available A simple method is presented for evaluating the water-proofness quality of paints on lining materials. The method is based on measuring the integral capillarity in dependence on time, and then comparing this value to the value determined for the basic lining material. Measurements of the effective water vapor permeability then provide information on the risk of condensation which may increase after applying the paint. A practical application of the method is performed with four Karlocolor paints on glass concrete substrates. All the Karlocolor paints are found to be very effective materials for driven rain protection. The diffusion properties of all the paints are found to be excellent.

  11. [Internal contamination by tritium caused by radioluminescent paints].

    Science.gov (United States)

    Adamiak-Ziemba, J; Doniec, J

    1985-01-01

    The internal contamination investigations covered 23 persons using radioluminescence paints containing tritium, assembling devices painted with those paints, and those having no contact with active paints but working next to the painting room. Determined were concentrations of tritium excreted with urine, air contamination at workplaces, contamination of workplace areas and hand skin. At the time covered by the investigations, the mean annual equivalent doses for those using tritium paints were reduced from 14-20 mSv to about 5 mSv. In those working next to the painting room they were reduced from 5.8-15 to 0.23 mSv. The exposure of those assembling the devices does not exceed 1 mSv. It was demonstrated that the main cause of the tritium exposure level was air contamination in working rooms.

  12. Fuzzy logic for large mining bucket wheel reclaimer motion control——from an engineer's perspective

    Institute of Scientific and Technical Information of China (English)

    LU Tienfu

    2011-01-01

    The bucket wheel reclaimer(BWR)is a key piece of equipment which has been widely used for stacking and reclaiming bulk materials(i. e. iron ore and coal)in places such as ports, iron-steel plants, coal storage areas, and power stations from stockpiles. BWRs are very large in size, heavy in weight, expensive in price, and slow in motion. There are many challenges in attempting to automatically control their motion to accurately follow the required trajectories involving uncertain parameters from factors such as friction, turbulent wind, its own dynamics, and encoder limitations. As BWRs are always heavily engaged in production and cannot be spared very long for motion control studies and associated developments, a BWR model and simulation environment closely resembling real life conditions would be beneficial. The following research focused mainly on the implementation of fuzzy logic to a BWR motion control from an engineer's perspective. First, the modeling of a BWR including partially known parameters such as friction force and turbulence to the system was presented. This was then followed by the design of a fuzzy logic-based control built on a model-based control loop. The investigation provides engineers with an example of applying fuzzy logic in a model based approach to properly control the motion of a large BWR following defined trajectories, as well as to show possible ways of further improving the controller performance. The result indicates that fuzzy logic can be applied easily by engineers to overcome most motion control issues involving a large BWR.

  13. Fresco paintings studied by unilateral NMR

    Science.gov (United States)

    Proietti, N.; Capitani, D.; Lamanna, R.; Presciutti, F.; Rossi, E.; Segre, A. L.

    2005-11-01

    Unilateral NMR has been used to monitor the state of conservation of frescoes in the Vasari's house in Florence. The causes of deterioration of ancient frescoes are varied, which result in the detachment and crumbling of the painted film from the supporting plaster and in the outcropping of salts. Unilateral measurements of Hahn echo performed on such frescoes have allowed a perfect identification of the detachment of the painted film from the plaster. The presence of soluble salts on the pictorial film affects the spin-spin relaxation times, T2. It is then possible using this technique, to characterize the effect of chemical treatments, of cleansing and consolidation procedures using the distribution of T2 spin-spin relaxation times.

  14. Electrochemical assessment of magnetite anticorrosive paints

    Directory of Open Access Journals (Sweden)

    Escobar, D. M.

    2003-12-01

    Full Text Available With the purpose of deepening in the understanding of the mechanisms of protection of anticorrosive pigments based on iron oxides, this work has been carried out on the production of pure magnetite, and copper and chromium doped magnetite, which were evaluated by different characterization techniques. The paints were prepared with a solvent less epoxy resin maintaining the Pigment Volume Content near the Practical Critical value (CPVC, established for each pigment. The paints were applied on polished steel and monitored with electrochemical techniques at total immersion conditions. Permeability and impedance measurements of free films were also done. Impedance data were simulated with the Boukamp software. Results show that the paints pigmented with doped magnetite present better behavior than a paint prepared with commercial hematite.

    Con el propósito de profundizar en el entendimiento de los mecanismos de protección de los pigmentos anticorrosivos a base de óxidos de hierro, se sintetizaron y caracterizaron magnetitas puras y dopadas con cobre y cromo, con las cuales se prepararon pinturas anticorrosivas que fueron evaluadas en ensayos acelerados de campo y laboratorio. Las pinturas fueron especialmente preparadas con una resina libre de solvente manteniendo la Concentración Pigmentaria en Volumen cercana al valor Crítico (CPVC, establecida para cada pigmento. Las pinturas fueron aplicadas sobre acero pulido y evaluadas con técnicas electroquímicas en condiciones de inmersión total. Para complementar el estudio se realizaron medidas de permeabilidad e impedancia sobre las películas libres. Los datos de impedancia se simularon con el programa Boukamp. Los resultados muestran que las pinturas pigmentadas con magnetitas dopadas presentan mejor comportamiento que las preparadas con hematita comercial.

  15. Biological Treatment of Solvent-Based Paint

    Science.gov (United States)

    2011-01-01

    solvent. In addition, hydrocarbon mixtures, aromatic hydrocarbon, and Medium Aliphatic Solvent Naphtha are descriptors used by the manufactures to...Enamel Aromatic Hydrocarbon 14 Mineral Spirits 10 Naphtha 10 Ethyl Benzene 0.21 Xylene 1.0 Sherwin Williams Co Enamel Mineral Spirits 49...Solvent Naphtha 31.5 Non-hazardous Ingredients 68 Parker Paints Enamel Mineral Spirits 17 Naphtha 7 Aromatic Hydrocarbons 3 1,2,4

  16. Biological Treatment of Solvent-Based Paint

    Science.gov (United States)

    2011-01-01

    GAC granular activated carbon H2O water HP horsepower IWG inches of water gauge IWTC Industrial Wastewater Treatment Complex JGDM Joint...biofiltration system) were procured, installed, and tested over a 1-yr period in cooperation with the Industrial Wastewater Treatment Complex (IWTC) in...were steam reforming, incineration, ultrafiltration , activated carbon, and photochemical oxidation. Because the paint is not suspended in water, its

  17. Role of microorganisms in mural paintings decay

    OpenAIRE

    Rosado, T; J. Mirão; Gil, M.; Candeias, A.; Caldeira, A. T.

    2014-01-01

    The action of microbial communities on mural paintings, particularly in mortars and in pictorial layers, triggered numerous studies to identify the main biodeteriogenic agents and to better understand the role of microorganisms in the biodeterioration/biodegradation of these artworks. The biodegradation phenomenon is an important issue for the conservation of cultural heritage that needs urgent answers to their rehabilitation. Microbial activity and their ability to obtain elements by bios...

  18. Stylometry of Painting Techniques - A Survey

    OpenAIRE

    Sanaz keshvari; Abdolah Chalechale

    2016-01-01

    To discover a scientific relationship for art is an interesting and challenging problem. Recognition of artist Identification and stylometry of painting have been important issues at artwork. Image processing techniques can be an effective solution for resolving these problem. To the best of our knowledge, these problems have not been widely investigated. This paper presents a comprehensive survey about both proposed stylometry approaches and artist identification. Finally, It also compares a...

  19. Stylometry of Painting Techniques - A Survey

    Directory of Open Access Journals (Sweden)

    Sanaz keshvari

    2016-12-01

    Full Text Available To discover a scientific relationship for art is an interesting and challenging problem. Recognition of artist Identification and stylometry of painting have been important issues at artwork. Image processing techniques can be an effective solution for resolving these problem. To the best of our knowledge, these problems have not been widely investigated. This paper presents a comprehensive survey about both proposed stylometry approaches and artist identification. Finally, It also compares and summarizes all reviewed methods.

  20. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like......, for example, gutters, window frames, car parts and transportation boxes have long lifetimes and thus appear as waste only many years after they have been introduced on the market. Plastic is constantly being used for new products because of its attractive material properties: relatively cheap, easy to form......, good strength and long durability. Recycling of plastic waste from production is well-established, while recycling of postconsumer plastic waste still is in its infancy. This chapter describes briefly how plastic is produced and how waste plastic is recycled in the industry. Quality requirements...

  1. Blanching of paint and varnish layers in easel paintings: contribution to the understanding of the alteration

    Science.gov (United States)

    Genty-Vincent, Anaïs; Eveno, Myriam; Nowik, Witold; Bastian, Gilles; Ravaud, Elisabeth; Cabillic, Isabelle; Uziel, Jacques; Lubin-Germain, Nadège; Menu, Michel

    2015-11-01

    The blanching of easel paintings can affect the varnish layer and also the paint layer with a blurring effect. The understanding of the physicochemical and optical phenomena involved in the whitening process remains an important challenge for the painting conservation. A set of ca. 50 microsamples from French, Flemish, and Italian blanched oil paintings, from sixteenth to nineteenth century, have been collected for in deep investigations. In parallel, the reproduction of the alteration was achieved by preparing some paint layers according to historical treatises and altering them in a climatic chamber in a humid environment or directly by immersing in ultrapure water. The observation of raw samples with a field-emission gun scanning electron microscope revealed for the first time that the altered layers have an unexpected highly porous structure with a pore size ranging from ca. 40 nm to 2 μm. The formation mechanism of these pores should mostly be physical as the supplementary analyses (Fourier transform infrared spectroscopy, gas chromatography-mass spectrometry) do not reveal any noticeable molecular modification. Considering the tiny size of the pores, the alteration can be explained by the Rayleigh or Mie light scattering.

  2. Capability to Paint and Alzheimer’s Disease

    Directory of Open Access Journals (Sweden)

    Emelie Miller

    2016-02-01

    Full Text Available Although quite many qualitative studies on painting in Alzheimer’s disease (AD have been conducted, there is a lack of quantitative studies, examining the ability to paint in people with AD in relation to disease stages, and to what extent instructions are associated with actual performance. The present study aimed at investigating the capability to paint among nonartist AD participants (N = 17 in an instructed painting condition versus a noninstructed painting condition. Differences in time spent and area of canvas used in the two painting conditions were assessed and related to scores on the Mini Mental State Examination (MMSE and the Clock Test. Number of colors used and color preferences were also assessed. A within-subjects experimental design was used. Analyses revealed a statistically significant difference between time and area used in the two painting conditions, where both time and area were used more in the noninstructed condition. MMSE scores and scores on the Clock Test correlated significantly with time spent in both conditions. Higher scores predicted longer painting sessions. Mean number of colors used was 5. Color preferences were bright colors in general and green in particular. Possible artistic development was noted. The overall conclusion is that people with AD have a preserved capability to paint, with and without instructions, even those in the later stages of the disease. The results also indicate that an artistic development is possible and that painting can be used as an appreciated and beneficial activity for people with AD.

  3. Difference in brain activations during appreciating paintings and photographic analogs.

    Science.gov (United States)

    Mizokami, Yoshinori; Terao, Takeshi; Hatano, Koji; Hoaki, Nobuhiko; Kohno, Kentaro; Araki, Yasuo; Kodama, Kensuke; Makino, Mayu; Izumi, Toshihiko; Shimomura, Tsuyoshi; Fujiki, Minoru; Kochiyama, Takanori

    2014-01-01

    Several studies have investigated neural correlates of aesthetic appreciation for paintings but to date the findings have been heterogeneous. This heterogeneity may be attributed to previous studies' measurement of aesthetic appreciation of not only the beauty of paintings but also the beauty of motifs of the paintings. In order to better elucidate the beauty of paintings, it seems necessary to compare aesthetic appreciation of paintings and photographic analogs which included corresponding real images. We prepared for famous painters' pictures and their photographic analogs which were set up to resemble each painting in order to investigate the hypothesis that there exist specific neural correlates associated with the aesthetic appreciation for paintings. Forty-four subjects participated in functional magnetic resonance study which required comparisons of aesthetic appreciation of paintings of still life and landscape versus photographic analogs including corresponding real images of still life and landscape. Bilateral cuneus and the left lingual gyrus were activated in the comparison of aesthetic appreciation of paintings versus photographic analogs. In conclusion, the present findings suggest a possibility of the existence of specific neural correlates associated with the aesthetic appreciation for paintings and that bilateral cuneus and the left lingual gyrus may be involved.

  4. Nanoparticles Ni electroplating and black paint for solar collector applications

    Directory of Open Access Journals (Sweden)

    J. El Nady

    2016-06-01

    Full Text Available A nanoparticles layer of bright nickel base was deposited on copper substrates using electrodeposition technique before spraying the paint. IR reflectance of the paint was found to be around 0.4 without bright nickel layer and the reflectance increased to 0.6 at a Ni layer thickness of 750 nm. The efficiency of the constructed solar collectors using black paint and black paint combined with bright nickel was found to be better than black paint individually. After aging tests under high temperature, Bright nickel improved the stability of the absorber paint. The collector optical gain FR(τα was lowered by 24.7% for the commercial paint and lowered by 19.3% for the commercial paint combined with bright nickel. The overall heat loss FR(UL was increased by 3.3% for the commercial paint and increased by 2.7% for the commercial paint combined with bright nickel after the temperature aging test.

  5. Statistics Analysis Measures Painting of Cooling Tower

    Directory of Open Access Journals (Sweden)

    A. Zacharopoulou

    2013-01-01

    Full Text Available This study refers to the cooling tower of Megalopolis (construction 1975 and protection from corrosive environment. The maintenance of the cooling tower took place in 2008. The cooling tower was badly damaged from corrosion of reinforcement. The parabolic cooling towers (factory of electrical power are a typical example of construction, which has a special aggressive environment. The protection of cooling towers is usually achieved through organic coatings. Because of the different environmental impacts on the internal and external side of the cooling tower, a different system of paint application is required. The present study refers to the damages caused by corrosion process. The corrosive environments, the application of this painting, the quality control process, the measures and statistics analysis, and the results were discussed in this study. In the process of quality control the following measurements were taken into consideration: (1 examination of the adhesion with the cross-cut test, (2 examination of the film thickness, and (3 controlling of the pull-off resistance for concrete substrates and paintings. Finally, this study refers to the correlations of measurements, analysis of failures in relation to the quality of repair, and rehabilitation of the cooling tower. Also this study made a first attempt to apply the specific corrosion inhibitors in such a large structure.

  6. [Deafness and mentality in Francisco Goya's paintings].

    Science.gov (United States)

    Betlejewski, Stanisław; Ossowski, Roman

    2009-01-01

    The famous painter Francisco Goya y Lucientes (1746-1828) suffered during his life one or several diseases, the nature of which has not been determined with certainty. At age of 46, Goya suffered from severe illness that lasted a few months. It caused loss of vision and hearing, tinnitus, dizziness, a right-sides paralysis, weakness and general malaise. Although he recovered from a cerebral stroke which accompanied it, the deafness remained unaltered. The illness divides Goya's artistic life into two great different periods. After in the painter produces his greatest works. The visual experience after the illness was heightened by the exclusion of acoustics stimuli and the artist's talent rose to the highest level. His character became more withdrawn and introspective and his entire vitality was direscted to his painting. Goya's painting became progressively more gloom and satirical during his long convalescence. The artist suffered a stroke at age 73 that again rendered him paralysed on the right side. The precise cause of his illness has long been debated. Ome medical writers have favored the diagnosis of syphilis, some consider the possibility of an exogenous psychosis, and other suggests that the symptoms of the illness are more congruent with heavy metal poisoning, particulary lead. It is interesting to speculate how the Goya's deafness influenced the artist's mentality and the changes of his painting. Interesting is also the problem of the sensory compensation in fact of disturbance of physiological function of one of the senses.

  7. Failure in Anticipation and Plasticity in Perception of Taste

    Science.gov (United States)

    Moriyama, Tohru; Yokokawa, Sari; Tsukahara, Yasuo

    2006-06-01

    Experiments were designed to illustrate the plasticity of gustatory processing in human. In the matching experiment, forty-two subjects were respectively given twenty-four samples, each of which consisted of a usual pair of taste and visual stimuli (ex; a cup of apple juice covered with a lid having an apple painted on it). They were required to drink the taste stimulus while looking at the visual one. Subsequently, they were required to drink a cup of water covered with a lid with an Escher's impossible-figure painted on it and asked whether the taste was the same as that of usual one or not. In the mismatching experiment, the same subjects were respectively given twenty samples each of which consisted of an unusual pair of taste and visual stimuli (ex; a cup of soup covered with a lid having an apple painted on it). They were required to drink the taste stimulus while looking at the visual one. Subsequently, they were required to drink a cup of water covered with a lid with an Escher's impossible-figure painted on it and asked whether the taste was the same as that of usual one or not. Eight subjects sensed taste to water (p 0.05) after the matching one.

  8. Self Cleaning Paint: Introduction of Photocatalytic Particles into a Paint System

    DEFF Research Database (Denmark)

    Gunnarsson, Sverrir Grimur

    consists of an introduction to relevant concepts and literature followed by results, presented as research papers, and a patent application. Four research papers are introduced as individual chapters. Chapter 4 discusses the synthesis and optimisation of anatase TiO2 coated microspheres, chapter 5...... discusses the self-cleaning properties and degradation mechanisms of photocatalytic organic coatings containing TiO2 coated microspheres, chapter 6 discusses the rheological and mechanical properties of such coatings and chapter 7 discusses the durability and weather stability of photocatalytic self......-cleaning coatings containing TiO2 coated microspheres. The results show that introducing a photocatalyst into an organic paint system as a coating on inert carrier particles results in durable and weather stable paint films. The paint films exhibit selfcleaning properties and are able to resist the attack of micro...

  9. 77 FR 54930 - Carlyle Plastics and Resins, Formerly Known as Fortis Plastics, A Subsidiary of Plastics...

    Science.gov (United States)

    2012-09-06

    ... Employment and Training Administration Carlyle Plastics and Resins, Formerly Known as Fortis Plastics, A... plastic parts. New information shows that Fortis Plastics is now called Carlyle Plastics and Resins. In... of Carlyle Plastics and Resins, formerly known as Fortis Plastics, a subsidiary of...

  10. The extraction and preliminary characterization of paint oil and paint wax

    Institute of Scientific and Technical Information of China (English)

    Ren Yingjie; Wu Maoyu; Zhang Feilong

    2012-01-01

    To study the best technology of extraction of paint wax and paint seed oil, we performed the single factor experiment and analyzed the composition of different varieties of paint oil by infrared analysis. The results show that: the optimum conditions for paint wax, are that, using petroleum ether(30℃ -60℃ ) as extracting agent, extraction temperature 50℃, ratio of solid to liquid 1 : 20, the extraction time 12h, paint seed skin mesh size, greater than 100 ; optimum conditions for paint oil are that, petroleum ether( 30℃ -60℃ ) as extracting agent, extraction temperature 50℃, ratio of solid to liquid 1 : 30, the extraction time 3h, paint seed skin mesh size greater than 100. Extracted paint oil' s IR spectral peak positions are basically the same, which indicates that their chemical compositions are basically the same.%研究漆籽油和漆蜡提取的最佳工艺,进行单因素实验,对不同品种漆油进了红外分析。结果表明:漆蜡的最佳工艺条件是:石油醚(30℃~60℃)作为提取剂,提取温度为50℃,固液比为1∶20,提取时间12h,漆籽皮的目数是大于100目;漆油的最佳工艺条件是:石油醚(30℃~60℃)作为提取剂,提取温度为50℃,固液比为1∶30,提取时间3h,漆籽皮的目数是大于100目。通过萃取所得的漆油在红外图谱上出峰位置基本一致,表明其化学成分基本相同。

  11. Our plastic age

    National Research Council Canada - National Science Library

    Richard C. Thompson; Shanna H. Swan; Charles J. Moore; Frederick S. vom Saal

    2009-01-01

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production...

  12. Weinig plastic in vissenmaag

    NARCIS (Netherlands)

    Foekema, E.M.

    2012-01-01

    Waar de magen van sommige zeevogels vol plastic zitten, lijken vissen in de Noordzee nauwelijks last te hebben van kunststofafval. Onderzoekers die plastic resten zochten in vissenmagen vonden ze in elk geval nauwelijks.

  13. Ear Plastic Surgery

    Science.gov (United States)

    ... ENTCareers Marketplace Find an ENT Doctor Near You Ear Plastic Surgery Ear Plastic Surgery Patient Health Information ... they may improve appearance and self-confidence. Can Ear Deformities Be Corrected? Formation of the ear during ...

  14. Computerized Comparison and Analysis of Vincent van Gogh's Painting Brushstrokes

    Science.gov (United States)

    Wang, James Z.

    2009-03-01

    With advanced digitization techniques, museums have routinely begun to assemble vast digital libraries of images of their collections. These images can be analyzed by computers to assist art historians for a number of tasks. In our work, we focus on three challenges: artist identification, dating of an art work, and finding distinguishing features among artists. Two complementary approaches were taken: (1) the analysis of the geometric statistics based on the extracted individual brushstroke, and (2) the modeling of overall brushstroke texture. These approaches aim at assisting art historians in comparing a painting or parts of a painting to a group of paintings based on multiple criteria. Statistical methods have been used to compare groups of paintings. Each painting image is divided into subimages. Individual brushstrokes are segmented automatically. Geometric features, including the curvature, the overall orientation, and the size, are computed for each brushstroke. We also compute the features representing the interactivity of the brushstrokes extracted. The statistics, including average and standard deviation, of those features are used to model certain aspects of the artist's brushstrokes. For capturing the local brushstroke texture, we first apply a wavelet transform to the image. A spatial model, the 2-D hidden Markov model, is used to model the texture features of each subimage. The methods have shown to be able to distinguish van Gogh paintings and non van Gogh paintings to a great extent. The techniques can provide clues for the dating of van Gogh paintings. A comparison of the van Gogh paintings, Monticelli's paintings, and paintings by contemporary artists provides insights on their similarities and differences. The analysis has provided numerical statistics for further studying these and other paintings.

  15. Alternative Solvents/Technologies for Paint Stripping: Phase 1.

    Science.gov (United States)

    1994-03-01

    and: PZ 600 N-Methylpyrrolidone >50 100 mg/L Turco:Trco Hydrotreated Napthenic Distillate 15 5 m/r 3 Monoethanol Amine 30 3 mg/L N-Methylpyrrolidone 45... amines . Organic acids such as formic acid hydrolyze ether linkages in the paint film and destroy crosslinking to allow rapid penetration of the primary...as water, acids, and amines in the paint strippers. g. Surfactants Surfactants assist in the removal of the softened paint and stripper residues. 3

  16. Smart Surfaces: New Coatings & Paints with Radiation Detection Functionality

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, J; Choi, J

    2007-03-12

    Paints are being developed and tested that might ultimately be able to detect radiological agents in the environment by incorporating special pigments into an organic polymeric binder that can be applied as a paint or coatings. These paints detect radioactive sources and contaminants with inorganic or organic scintillation or thermo-luminescent pigments, which are selected based upon the radiation ({alpha}, {beta}, {gamma} or n) to be detected, and are shown in Figure 1.

  17. Biodegradability of Plastics

    OpenAIRE

    Yutaka Tokiwa; Calabia, Buenaventurada P.; Charles U. Ugwu; Seiichi Aiba

    2009-01-01

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical ...

  18. Trompe l'oeil painting for the scientific illustrator.

    Science.gov (United States)

    Hodge, G P

    2000-01-01

    Trompe l'oeil is a French term meaning fool-the-eye. When this concept is applied to the art of painting, the painted objects must look as convincingly real as do the actual objects. With the scientific illustrator having a background of rendering concepts which are realistic and accurate, he or she should have no trouble moving into the trompe l'oeil fine art field. The author lists the necessary aspects of why a trompe l'oeil painting is different from a realistic scientific illustration, a still life, or a landscape painting.

  19. A qualitative study of student responses to body painting.

    Science.gov (United States)

    Finn, Gabrielle M; McLachlan, John C

    2010-01-01

    One hundred and thirty-three preclinical medical students participated in 24 focus groups over the period 2007-2009 at Durham University. Focus groups were conducted to ascertain whether or not medical students found body painting anatomical structures to be an educationally beneficial learning activity. Data were analyzed using a grounded theory approach. Five principal themes emerged: (1) body painting as a fun learning activity, (2) body painting promoting retention of knowledge, (3) factors contributing to the memorability of body painting, (4) removal from comfort zone, and (5) the impact of body painting on students' future clinical practice. Students perceive body painting to be a fun learning activity, which aids their retention of the anatomical knowledge acquired during the session. Sensory factors, such as visual stimuli, especially color, and the tactile nature of the activity, promote recall. Students' preference for painting a peer or being painted is often dependent upon their learning style, but there are educational benefits for both roles. The moderate amounts of undressing involved encouraging students to consider issues surrounding body image; this informs their attitudes towards future patients. Body painting is a useful adjunct to traditional anatomy and clinical skills teaching. The fun element involved in the delivery of this teaching defuses the often formal academic context, which in turn promotes a positive learning environment. Copyright 2009 American Association of Anatomists.

  20. Preventive conservation applied to "Casa dos Patudos" oil painting collection

    Directory of Open Access Journals (Sweden)

    Mafalda Fernandes

    2016-01-01

    Full Text Available The main objective of this work was the identification of specific risks affecting the collection of oil paintings in the historic house "Casa dos Patudos" (Alpiarça, Portugal and the development of mitigation strategies for the risks encountered. The methodology used was proposed by the Canadian Conservation Institute. The results showed that the main risks affecting this collection result from incorrect handling, increase in paint detachment due to the maintenance of paintings with paint lifting on display, occurrence of insect pests, high fluctuations in relative humidity and, excessive exposure to ultraviolet radiation. Several preventive conservation strategies to mitigate these risks are proposed.

  1. Revealing pentimenti: the hidden history in a painting

    Science.gov (United States)

    Gooch, Amy A.

    2007-02-01

    Art conservators often explore X-ray images of paintings to help find pentimenti, the artist's revisions hidden beneath the painting's visible first surfaces. X-ray interpretation is difficult due to artifacts in the image, superimposed features from all paint layers, and because image intensity depends on both the paint layer thickness and each pigment's opacity. We present a robust user-guided method to suppress clutter, find visually significant differences between X-ray images and color photographs, and visualize them together. These tools allow domain experts as well as museum visitors to explore the artist's creative decisions that led to a masterpiece.

  2. Astronomical Dating of Edvard Munch's Summer Sky Paintings

    Science.gov (United States)

    Pope, Ava; Olson, Donald

    2010-02-01

    Norwegian painter Edvard Munch, most famous for The Scream, created many spectacular works depicting the skies of Norway. Our Texas State group used astronomical methods to analyze three of these paintings: Starry Night, The Storm, and Sunrise in Asgardstrand. Astronomical dating of these paintings has some importance because the precise days when Munch visited Asgardstrand are unknown. Our research group traveled to Norway in August 2008 to find the locations from which Munch painted these three works. We then used astronomical calculations, topographical analysis, historical photographs, and weather records to determine the precise dates and times for the scenes depicted in these paintings. )

  3. Chemical Recycle of Plastics

    Directory of Open Access Journals (Sweden)

    Sara Fatima

    2014-11-01

    Full Text Available Various chemical processes currently prevalent in the chemical industry for plastics recycling have been discussed. Possible future scenarios in chemical recycling have also been discussed. Also analyzed are the effects on the environment, the risks, costs and benefits of PVC recycling. Also listed are the various types of plastics and which plastics are safe to use and which not after rcycle

  4. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example...

  5. Estimation of Heights of Soil Plug Inside Bucket Foundations During Suction Penetration by Deformable Discrete Element Modeling

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The soil plug phenomenon involving the rising of the surface soil inside the bucket chamber under the suction pressure and seepage forces was simulated and calculated by deformable discrete element method (DDEM) models. The seepage forces, the effective gravity of soil, the friction on the chamber wall and the suction inside the chamber are considered as the main external forces of DDEM specimen. Three typical types of soil (silty clay, silt and sand) in the Bohai Sea are set as the main environmental conditions in the formation process of soil plug. It is found that the heights of soil plug simulated by DDEM models are 161.85 mm in silty clay, 125.22 mm in silt and 167.56 mm in sand, which are close to model test results and higher than those estimated by discrete element method (DEM). DDEM is an effective method to estimate and predict the heights of soil plug before suction penetration of bucket foundations on site.

  6. Paintings in Atlantic Megalithic Art: Barnenez

    Directory of Open Access Journals (Sweden)

    Bueno Ramírez, Primitiva

    2012-06-01

    Full Text Available The use of technique is usually considered in European megalithic art as an indicator of the level of culture sophistication attained by a particular community. Traditionally, it was considered that only the Iberian Peninsula is home to painted dolmens. The analysis of chamber H of the Barnenez tumulus together with some information scattered over the continent, prove that painting was part of the graphic programs in the most archetypal Atlantic sites, such as Brittany. A highly rewarding panorama appears for European megalithic art with potential new readings. The most suitable method of detecting paintings and interpreting them in funerary contexts must be reviewed.

    La técnica ha venido estableciéndose en el arte megalítico europeo como una categoría cultural. Solo la Península Ibérica disponía de dólmenes pintados. Pero algunos datos dispersos en el resto del continente, junto con los análisis que se aportan procedentes de la cámara H del túmulo de Barnenez, certifican que la pintura formó parte de los programas gráfi cos de los más clásicos conjuntos atlánticos, como es el bretón. Se abre un panorama muy enriquecedor de nuevas lecturas para un arte megalítico europeo en el que habrá de contemplarse la metodología pertinente para la detección de pinturas y su interpretación en los discursos funerarios.

  7. Thermal characterization of intumescent fire retardant paints

    Science.gov (United States)

    Calabrese, L.; Bozzoli, F.; Bochicchio, G.; Tessadri, B.; Rainieri, S.; Pagliarini, G.

    2014-11-01

    Intumescent coatings are now the dominant passive fire protection materials used in industrial and commercial buildings. The coatings, which usually are composed of inorganic components contained in a polymer matrix, are inert at low temperatures and at higher temperatures, they expand and degrade to provide a charred layer of low conductivity materials. The charred layer, which acts as thermal barrier, will prevent heat transfer to underlying substrate. The thermal properties of intumescent paints are often unknown and difficult to be estimated since they vary significantly during the expansion process; for this reason the fire resistance validation of a commercial coatings is based on expensive, large-scale methods where each commercial coating-beam configuration has to be tested one by one. Adopting, instead, approaches based on a thermal modelling of the intumescent paint coating could provide an helpful tool to make easier the test procedure and to support the design of fire resistant structures as well. The present investigation is focused on the assessment of a methodology intended to the restoration of the equivalent thermal conductivity of the intumescent layer produced under the action of a cone calorimetric apparatus. The estimation procedure is based on the inverse heat conduction problem approach, where the temperature values measured at some locations inside the layer during the expansion process are used as input known data. The results point out that the equivalent thermal conductivity reached by the intumescent material at the end of the expansion process significantly depends on the temperature while the initial thickness of the paint does not seem to have much effect.

  8. Impact on the environment from steel bridge paint deterioration using lead isotopic tracing, paint compositions and soil deconstruction.

    Science.gov (United States)

    Gulson, Brian; Chiaradia, Massimo; Davis, Jeffrey; O'Connor, Gary

    2016-04-15

    Deterioration and repair of lead paint on steel structures can result in contamination of the ambient environment but other sources of lead such as from past use of leaded paint and gasoline and industrial activities can also contribute to the contamination. Using a combination of high precision lead isotopic tracing, detailed paint examination, including with scanning electron microscopy, and soil deconstruction we have compared paint on a steel bridge and bulk soil and lead-rich particles separated from soil. The majority of Pb found in the paint derives from Australian sources but some also has a probable US origin. The isotopic data for the bulk soils and selected particles lie on a mixing line with end members the geologically ancient Broken Hill lead and possible European lead which is suggested to be derived from old lead paint and industrial activities. Data for gasoline-derived particulates lie on this array and probably contribute to soil Pb. Although paint from the bridge can be a source of lead in the soils, isotopic tracing, paint morphology and mineralogical identification indicate that other sources, including from paint, gasoline and industrial activities, are contributing factors to the lead burden. Even though physical characteristics and elemental composition are the same in some particles, the isotopic signatures demonstrate that the sources are different. Plots using (206)Pb/(208)Pb vs (206)Pb/(207)Pb ratios, the common representation these days, do not allow for source discrimination in this investigation.

  9. Investigating shoulder muscle loading and exerted forces during wall painting tasks: influence of gender, work height and paint tool design.

    Science.gov (United States)

    Rosati, Patricia M; Chopp, Jaclyn N; Dickerson, Clark R

    2014-07-01

    The task of wall painting produces considerable risk to the workers, both male and female, primarily in the development of upper extremity musculoskeletal disorders. Insufficient information is currently available regarding the potential benefits of using different paint roller designs or the possible adverse effects of painting at different work heights. The aim of this study was to investigate the influence of gender, work height, and paint tool design on shoulder muscle activity and exerted forces during wall painting. Ten young adults, five male and five female, were recruited to perform simulated wall painting at three different work heights with three different paint roller designs while upper extremity muscle activity and horizontal push force were recorded. Results demonstrated that for female participants, significantly greater total average (p = 0.007) and integrated (p = 0.047) muscle activity was present while using the conventional and curly flex paint roller designs compared to the proposed design in which the load was distributed between both hands. Additionally, for both genders, the high working height imposed greater muscular demands compared to middle and low heights. These findings suggest that, if possible, avoid painting at extreme heights (low or high) and that for female painters, consider a roller that requires the use of two hands; this will reduce fatigue onset and subsequently mitigate potential musculoskeletal shoulder injury risks.

  10. Biodegradability of plastics.

    Science.gov (United States)

    Tokiwa, Yutaka; Calabia, Buenaventurada P; Ugwu, Charles U; Aiba, Seiichi

    2009-08-26

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.). In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  11. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example......, plastics from WEEE is chosen as a Nordic case study. The project aims to propose a number of improvements for this value chain together with representatives from Nordic stakeholders. Based on the experiences made, a guide for other plastic value chains shall be developed....

  12. Biodegradability of Plastics

    Directory of Open Access Journals (Sweden)

    Yutaka Tokiwa

    2009-08-01

    Full Text Available Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.. In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  13. Journal of CHINA PLASTICS

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Journal of CHINA PLASTICS was authorized and approved by The State Committee of Science and Technology of China and The Bureau of News Press of China, and published by The China Plastics Processing Industry Association,Beijing Technology and Business University and The Institute of Plastics Processing and Application of Light Industry, distributed worldwide. Since its birth in 1987, CHINA PLASTICS has become a leading magazine in plastics industry in China, a national Chinese core journal and journal of Chinese scientific and technological article statistics. It is covered by CA.

  14. Flood Overflows Jinshan Temple (Chinese Painting)

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The Chinese painting Flood Ouerflows Jinshan Temple draws its subject from a beautiful and well-known legend,The white Snake.In the tale Jinshan was an islet in the Yangtze River of yesteryear.Inorder to aave her husband kept in a temple at the top of the isle.Bai Niangzi.incarnation of the whitesnake.bravely fought Monk Fahat.She borrowed the Yangtze River’s water to overcome Jinshan Templeand force Fahai to release her husband.

  15. Mural Paintings in A Liao Tomb

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    It was a custom in the Liao Dynasty to decorate tombs with murals. The paintings in Zhao Dejun’s tomb, excavated in Beijing, provide a well-known example. During the Five Dynasties period, Zhao Dejun was a warlord in Youzhou, which became the southern capital of Nanjing in the Liao Dynasty (and even later, was renamed Beijing). The Zhaos grew to become a very powerful family in the area, as can be seen from the size of Zhao’s tomb and the value of the funerary objects buried with him. His tomb

  16. Immunodetection of proteins in ancient paint media.

    Science.gov (United States)

    Cartechini, Laura; Vagnini, Manuela; Palmieri, Melissa; Pitzurra, Lucia; Mello, Tommaso; Mazurek, Joy; Chiari, Giacomo

    2010-06-15

    Diagnostic immunology is a powerful tool, widely used in clinical and biochemical laboratories for detecting molecules. In recent years, the technique has been adapted to materials sciences as a result of the extensive advances achieved in immunology. Today, many companies supply custom antibodies as well as new high-performance bioprobes for virtually any use. The idea of using immunodetection in the field of conservation science is not new. This analytical methodology is, in fact, particularly attractive for investigating biopolymers in painting materials; it is highly sensitive and selective with respect to the biological source of the target molecules. Among biopolymers, proteins have been widely used in the past as painting binders, adhesives, and additives in coating layers. An accurate assessment of these materials is necessary to obtain deeper insights into an artist's technique as well as to design proper restoration and conservation methods. In spite of the diagnostic potential offered by immunodetection-based techniques, some analytical drawbacks had, until recently, limited their use in routine applications in conservation science. In this Account, we highlight the most important results achieved in our research on the development of analytical methodologies based on the use of enzyme-linked immunosorbent assay (ELISA) and immuno-fluorescence microscopy (IFM) techniques for the highly sensitive and specific identification of proteins in artistic and archeological materials. ELISA and IFM offer two alternative analytical routes to this final goal: ELISA provides a fast, cost-effective, quantitative analysis of microsamples put in solution, whereas IFM combines the immunodetection of the targeted molecules with the characterization of their spatial distribution. The latter approach is of great value in the stratigraphic investigation of paintings. We discuss the limits and strengths of these methodologies in the context of the complex matrixes usually

  17. Tangka Painting Art of the Tibetan Race (Ⅰ)

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    Tibetan painting art is mainly revealed in mural paintings aswell as tangka. Tangka incarnates not only the special character of Tibetan painting art but also the features of Tibetan traditional crafts and mounting.

  18. A method of using commercial virtual satellite image to check the pattern painting spot effect

    Science.gov (United States)

    Wang, Zheng-gang; Kang, Qing; Shen, Zhi-qiang; Cui, Chang-bin

    2014-02-01

    A method of using commercial virtual satellite image to check the pattern painting spot effect contrast with the satellite images before painting and after painting have been discussed. Using a housetop as the testing platform analyses and discusses the factors' influence such as resolution of satellite image, spot size and color of pattern painting spot and pattern painting camouflage method choosing to the plan implement. The pattern painting design and spot size used in the testing has been ensured, and housetop pattern painting has been painted. Finally, the small spot pattern painting camouflage effect of engineering using upon painting pattern size, color and texture have been checked, contrasting with the satellite image before painting and after painting.

  19. Challenges in plastics recycling

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Jakobsen, L. G.; Eriksen, Marie Kampmann

    2015-01-01

    Recycling of waste plastics still remains a challenging area in the waste management sector. The current and potential goals proposed on EU or regional levels are difficult to achieve, and even to partially fullfil them the improvements in collection and sorting should be considerable. A study...... was undertaken to investigate the factors affecting quality in plastics recycling. The preliminary results showed factors primarily influencing quality of plastics recycling to be polymer cross contamination, presence of additives, non-polymer impurities, and polymer degradation. Deprivation of plastics quality......, with respect to recycling, has been shown to happen throughout the plastics value chain, but steps where improvements may happen have been preliminary identified. Example of Cr in plastic samples analysed showed potential spreading and accumulation of chemicals ending up in the waste plastics. In order...

  20. Glassy metallic plastics

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    This paper reports a class of bulk metallic glass including Ce-, LaCe-, CaLi-, Yb-, and Sr-based metallic glasses, which are regarded as glassy metallic plastics because they combine some unique properties of both plastics and metallic alloys. These glassy metallic plastics have very low glass transition temperature (Tg~25oC to 150oC) and low Young’s modulus (~20 GPa to 35 GPa). Similar to glassy plastics, these metallic plastics show excellent plastic-like deformability on macro-, micro- and even nano-scale in their supercooled liquid range and can be processed, such as elongated, compressed, bent, and imprinted at low temperatures, in hot water for instance. Under ambient conditions, they display such metallic properties as high thermal and electric conductivities and excellent mechanical properties and other unique properties. The metallic plastics have potential applications and are also a model system for studying issues in glass physics.

  1. Augmenting painted architectures for communicating cultural heritage

    Directory of Open Access Journals (Sweden)

    Alberto Sdegno

    2015-07-01

    Full Text Available The paper presents a research under development at the University of Trieste to analyze a painted architecture by Paolo Veronese and to present the results using AR systems (Augmented Reality Systems. The canvas was painted in 1573 and it is now at the Gallerie dell’Accademia Museum in Venice. The aim of the research was to transform a two-dimensional work of art in a three dimensional one, allowing all the visitors of a museum to enter the space of the representation and perceive it in a more direct way. After the geometrical analysis of the picture, we started the digital restitution of the perspective references and proceed to model the virtual scene using Boolean primitives and applying all the textures to render the scene in a very realistic way. The further step was to convert the model into a dynamic form with AR algorithms and associate it with spatial references to allow users to do a virtual experience of it.

  2. The social lives of paintings in Sixteenth-Century Venice

    NARCIS (Netherlands)

    Kessel, Elisabeth Johanna Maria van

    2011-01-01

    This thesis studies Venetian painting in its golden age, the sixteenth century, from an unconventional, anthropological point of view. Paintings of masters like Titian are demonstrated to have had social lives. Together with human beings they were embedded in social networks in which humans and pain

  3. Chromosome-specific painting in Cucumis species using bulked oligonucleotides

    Science.gov (United States)

    Chromosome-specific painting is a powerful technique in molecular cytogenetic and genome research. We developed an oligonucleotide (oligo)-based chromosome painting technique in cucumber (Cucumis sativus) that will be applicable in any plant species with a sequenced genome. Oligos specific to a sing...

  4. Chromatic changes on the wall paintings in Sanderum Church (Denmark)

    DEFF Research Database (Denmark)

    Brajer, Isabelle Eve; Christensen, Mads Christian

    2011-01-01

    This paper describes observations and results of analyses undertaken to find explanations for several phenomena affecting the colours on the Gothic wall paintings in Sanderum Church (Denmark). Paintings have been exposed on four webs of the chancel vault and one web in the nave since 1882. Three...

  5. Quantitative imaging of heterogeneous dynamics in drying and aging paints

    NARCIS (Netherlands)

    Kooij, Van Der Hanne M.; Fokkink, Remco; Gucht, Van Der Jasper; Sprakel, Joris

    2016-01-01

    Drying and aging paint dispersions display a wealth of complex phenomena that make their study fascinating yet challenging. To meet the growing demand for sustainable, high-quality paints, it is essential to unravel the microscopic mechanisms underlying these phenomena. Visualising the governing

  6. SUBSTRATE EFFECTS ON VOC EMISSIONS FROM A LATEX PAINT

    Science.gov (United States)

    The effects of two substrates -- a stainless steel plate and a gypsum board -- on the volatile organic compound (VOC) emissions from a latex paint were evaluated by environmental chamber tests. It was found that the amount of VOCs emitted from the painted stainless steel was 2 to...

  7. Artists' Perception of the Use of Digital Media in Painting

    Science.gov (United States)

    Agyeman, Cynthia A.

    2015-01-01

    Painting is believed to predate recorded history and has been in existence for over 35,000 (Ayres, 1985; Bolton, 2013) years. Over the years, painting has evolved; new styles have been developed and digital media have been explored. Each period of change goes through a period of rejection before it is accepted. In the 1960s, digital media was…

  8. Replicas in Caravaggio's paintings: the correct use of scientific analysis

    Science.gov (United States)

    Diana, Maurizio; Moioli, Pietro; Seccaroni, Claudio

    1998-05-01

    Painting techniques and materials employed by Caravaggio are analyzed by X-ray fluorescence and radiography of unquestioned genuine works and compared to replicas of his earlier work. This approach is important in the attribution of recently discovered paintings and copies from the XVII century.

  9. 75 FR 39706 - Natural Bristle Paint Brushes From China

    Science.gov (United States)

    2010-07-12

    ... the antidumping duty order on natural bristle paint brushes from China (75 FR 21347, April 23, 2010... revoke the order on June 16, 2010 (75 FR 34097). In light of these developments, the Commission is... COMMISSION Natural Bristle Paint Brushes From China AGENCY: United States International Trade...

  10. Reconsidering Chinese Painting%中国画再审视

    Institute of Scientific and Technical Information of China (English)

    梁耀

    2001-01-01

    Reconsidering the traditional painting, including its philosophy and techniques, is always done by contemporary artists. The result is not very important. What we can concern is the expression in the painting, which would show the thinking progress, of the artist. Let's appreciate works of Mr. Liang Yao.

  11. 29 CFR 1915.33 - Chemical paint and preservative removers.

    Science.gov (United States)

    2010-07-01

    ... or alkalies, employees shall be protected by suitable face shields to prevent chemical burns on the... 29 Labor 7 2010-07-01 2010-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall...

  12. New biocide-free anti-fouling paints are toxic.

    Science.gov (United States)

    Karlsson, Jenny; Eklund, Britta

    2004-09-01

    A number of new anti-fouling paints claimed to be more friendly to the environment, have entered the market since prohibition of biocide containing paints have been enforced in many areas. Leakage waters from five new anti-fouling paints were tested for toxic effects to the macro algae Ceramium tenuicorne and Ceramium strictum and to the crustacean Nitocra spinipes. A banned copper and irgarol 1051 containing anti-fouling paint was used as reference. Five of the six paints tested were toxic to all or some of the organisms after two weeks of leakage with EC50 ranging from 0.08 to around 2% leakage water and LC50 ranging from 1.1% to 88%. The toxicity of leakage water from these paints was still high after 16 weeks. We conclude that these paints contain substances toxic to common organisms in the coastal Baltic ecosystem. A silicone based paint did not exhibit toxic effects to the two organisms. We recommend that biological tests should be used to identify the most harmful products before they are released on the market.

  13. The painting collection of baron Willem Vincent van Wyttenhorst

    NARCIS (Netherlands)

    Boers, M

    2004-01-01

    The Catholic Baron Willem Vincent van Wyttenhorst (1613-1674) from Utrecht was an enthusiastic collector of paintings. In his translation of Guarini's Il Pastor Fido, Hendrick Bloemaert even lauded Willem Vincent's 'Lofweerdigh cabinet' (commendable cabinet) of paintings. The inventory Wyttenhorst

  14. UN to lssue Stamps of Chinese Children’s Paintings

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    A set of stamps designed by Chinese children who took peace as their theme will be issued by the United Nations on October 25, 1996. This will be the first time the United Nations has used children’s paintings in its stamps. The paintings chosen are prize-winners of the Chinese national stamp-designing

  15. The painting collection of baron Willem Vincent van Wyttenhorst

    NARCIS (Netherlands)

    Boers, M

    2004-01-01

    The Catholic Baron Willem Vincent van Wyttenhorst (1613-1674) from Utrecht was an enthusiastic collector of paintings. In his translation of Guarini's Il Pastor Fido, Hendrick Bloemaert even lauded Willem Vincent's 'Lofweerdigh cabinet' (commendable cabinet) of paintings. The inventory Wyttenhorst m

  16. SPARK MACHINING FOR STEEL SURFACES TO IMPROVE PAINT COATINGS QUALITY

    Directory of Open Access Journals (Sweden)

    Sergey Levchenko

    2015-12-01

    Full Text Available Spark machining of steel surfaces enhances the subsequent paint coatings adhesion and protective properties. These factors improvement was confirmed at the salt-spray chamber testing and by both adhesion to the surface and depth of corrosion penetration below the paint coating layer measurements.

  17. The Monetary Appreciation of Paintings : From Realism to Magritte

    NARCIS (Netherlands)

    Renneboog, L.D.R.; van Houte, T.

    1999-01-01

    This study investigates how investments in painted arts compare to those in stocks in terms of risk return trade off using Sharpe and Treynor ratios and Markowitz efficient frontiers. A large database was analysed consisting of more than 10500 auction prices of Belgian painted art over the period 19

  18. Non-Photorealistic Rendering in Chinese Painting of Animals

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A set of algorithms is proposed in this paper to automatically transform 3D animal models to Chinese painting style. Inspired by real painting process in Chinese painting of animals, we divide the whole rendering process into two parts: borderline stroke making and interior shading. In borderline stroke making process we first find 3D model silhouettes in real-time depending on the viewing direction of a user. After retrieving silhouette information from all model edges, a stroke linking mechanism is applied to link these independent edges into a long stroke. Finally we grow a plain thin silhouette line to a stylus stroke with various widths at each control point and a 2D brush model is combined with it to simulate a Chinese painting stroke. In the interior shading pipeline, three stages are used to convert a Gouraud-shading image to a Chinese painting style image: color quantization, ink diffusion and box filtering. The color quantization stage assigns all pixels in an image into four color levels and each level represents a color layer in a Chinese painting. Ink diffusion stage is used to transfer inks and water between different levels and to grow areas in an irregular way. The box filtering stage blurs sharp borders between different levels to embellish the appearance of final interior shading image. In addition to automatic rendering, an interactive Chinese painting system which is equipped with friendly input devices can be also combined to generate more artistic Chinese painting images manually.

  19. Finite Element Modeling of Vibrations in Canvas Paintings

    NARCIS (Netherlands)

    Chiriboga Arroyo, P.G.

    2013-01-01

    Preventing vibration damage from occurring to valuable and sensitive canvas paintings is of main concern for museums and art conservation institutions. This concern has grown in recent years due to the increasing demand of paintings for exhibitions worldwide and the concomitant need for their handli

  20. Artists' Perception of the Use of Digital Media in Painting

    Science.gov (United States)

    Agyeman, Cynthia A.

    2015-01-01

    Painting is believed to predate recorded history and has been in existence for over 35,000 (Ayres, 1985; Bolton, 2013) years. Over the years, painting has evolved; new styles have been developed and digital media have been explored. Each period of change goes through a period of rejection before it is accepted. In the 1960s, digital media was…

  1. Application of variable-angle belt scale on bucket wheel machine%变角度电子皮带秤在斗轮机上的应用

    Institute of Scientific and Technical Information of China (English)

    徐红义; 毛志平; 鲁朝阳; 余松青; 许峰; 薛丁富

    2016-01-01

    This paper introduces the mathematical model of variable-angle electronic belt scale on Bucket wheel machine. Develop an belt scale that can automatically correct Span and Zero of Accumulator with the angle changing of belt conveyer. Improve Metrology accuracy of belt scale on Bucket wheel machine. Improve electrical belt scale accuracy installed on Bucket wheel machine. Ensure accuracy of coal blending, increase coal catch efficiency, energy conservation and environmental protection and decrees mechanical abrasion, increase durable years of Bucket wheel machine.%本文针对斗轮机输送机工况,深入研究电子皮带秤受力变化的数学模型,研制一套在斗轮机的悬臂角度改变后能够及时自动修正仪表的量程系数和零点的变角度电子皮带秤,提高安装在斗轮机上的电子皮带秤的计量准确度,保证了准确配煤,有效提高取料效率,节能环保,同时减少了与取料系统有关的传输机械设备的磨损,延长了斗轮机的使用年限。

  2. Population densities of painted buntings in the southeastern United States

    Science.gov (United States)

    Meyers, J. Michael

    2011-01-01

    The eastern population trend of Passerina ciris (Painted Bunting) declined 3.5% annually during the first 30 yrs of the Breeding Bird Survey (BBS, 1966–1996). Recently, the US Fish and Wildlife Service listed Painted Buntings as a focal species. Surveys for this focal species for the next 10 yrs (BBS, 1997–2007), however, are too low (2 in young pine plantations to 42 per km2 in maritime shrub. Effective detection radii for habitats varied from 64 to 90 m and were slightly higher in developed than in undeveloped habitats. Distance sampling is recommended to determine densities of Painted Buntings; however, large sample sizes (70–100 detections/habitat type) are required to monitor Painted Bunting densities in most habitats in the Atlantic coastal region of the southeastern United States. Special attention should be given to maritime shrub habitats, which may be important to maintaining the Painted Bunting population in the southeastern US.

  3. Quantitative imaging of heterogeneous dynamics in drying and aging paints.

    Science.gov (United States)

    van der Kooij, Hanne M; Fokkink, Remco; van der Gucht, Jasper; Sprakel, Joris

    2016-09-29

    Drying and aging paint dispersions display a wealth of complex phenomena that make their study fascinating yet challenging. To meet the growing demand for sustainable, high-quality paints, it is essential to unravel the microscopic mechanisms underlying these phenomena. Visualising the governing dynamics is, however, intrinsically difficult because the dynamics are typically heterogeneous and span a wide range of time scales. Moreover, the high turbidity of paints precludes conventional imaging techniques from reaching deep inside the paint. To address these challenges, we apply a scattering technique, Laser Speckle Imaging, as a versatile and quantitative tool to elucidate the internal dynamics, with microscopic resolution and spanning seven decades of time. We present a toolbox of data analysis and image processing methods that allows a tailored investigation of virtually any turbid dispersion, regardless of the geometry and substrate. Using these tools we watch a variety of paints dry and age with unprecedented detail.

  4. Automotive Painting Technology A Monozukuri-Hitozukuri Perspective

    CERN Document Server

    Salazar, Abraham; Saito, Kozo

    2013-01-01

    This book offers unique and valuable contributions to the field. It offers breadth and inclusiveness. Most existing works on automotive painting cover only a single aspect of this complex topic, such as the chemistry of paint or paint booth technology. Monozukuri and Hitozukuri are Japanese terms that can be translated as “making things” and “developing people” but their implications in Japanese are richer and more complex than this minimal translation would indicate. The Monozukuri-Hitozukuri perspective is drawn from essential principles on which the Toyota approach to problem-solving and continuous improvement is based. From this perspective, neither painting technology R&D nor painting technology use in manufacturing can be done successfully without integrating technological and human concerns involved with making and learning in the broadest sense, as the hyphen is meant to indicate. The editors provide case studies and examples -- drawn from Mr. Toda’s 33 years of experience with automotiv...

  5. Service-Learning General Chemistry: Lead Paint Analyses

    Science.gov (United States)

    Kesner, Laya; Eyring, Edward M.

    1999-07-01

    Houses painted with lead-based paints are ubiquitous in the United States because the houses and the paint have not worn out two decades after federal regulations prohibited inclusion of lead in paint. Remodeling older homes thus poses a health threat for infants and small children living in those homes. In a service-learning general chemistry class, students disseminate information about this health threat in an older neighborhood. At some of the homes they collect paint samples that they analyze for lead both qualitatively and quantitatively. This service-learning experience generates enthusiasm for general chemistry through the process of working on a "real" problem. Sample collection familiarizes the students with the concept of "representative" sampling. The sample preparation for atomic absorption spectroscopic (AAS) analysis enhances their laboratory skills. The focus of this paper is on the mechanics of integrating this particular service project into the first-term of the normal general chemistry course.

  6. Fly ash based zeolitic pigments for application in anticorrosive paints

    Science.gov (United States)

    Shaw, Ruchi; Tiwari, Sangeeta

    2016-04-01

    The purpose of this work is to evaluate the utilization of waste fly ash in anticorrosive paints. Zeolite NaY was synthesized from waste fly ash and subsequently modified by exchanging its nominal cation Na+ with Mg2+ and Ca2+ ions. The metal ion exchanged zeolite was then used as anticorrosive zeolitic pigments in paints. The prepared zeolite NaY was characterized using X-Ray diffraction technique and Scanning electron microscopy. The size, shape and density of the prepared fly ash based pigments were determined by various techniques. The paints were prepared by using fly ash based zeolitic pigments in epoxy resin and the percentages of pigments used in paints were 2% and 5%. These paints were applied to the mild steel panels and the anticorrosive properties of the pigments were assessed by the electrochemical spectroscopy technique (EIS).

  7. Fly ash based zeolitic pigments for application in anticorrosive paints

    Energy Technology Data Exchange (ETDEWEB)

    Shaw, Ruchi, E-mail: shawruchi1@gmail.com; Tiwari, Sangeeta, E-mail: stiwari2@amity.edu [Amity Institute of Applied Sciences, Amity University, Noida, Uttar Pradesh-201301 (India)

    2016-04-13

    The purpose of this work is to evaluate the utilization of waste fly ash in anticorrosive paints. Zeolite NaY was synthesized from waste fly ash and subsequently modified by exchanging its nominal cation Na{sup +} with Mg{sup 2+} and Ca{sup 2+} ions. The metal ion exchanged zeolite was then used as anticorrosive zeolitic pigments in paints. The prepared zeolite NaY was characterized using X-Ray diffraction technique and Scanning electron microscopy. The size, shape and density of the prepared fly ash based pigments were determined by various techniques. The paints were prepared by using fly ash based zeolitic pigments in epoxy resin and the percentages of pigments used in paints were 2% and 5%. These paints were applied to the mild steel panels and the anticorrosive properties of the pigments were assessed by the electrochemical spectroscopy technique (EIS).

  8. Transmittance spectroscopy and transmitted multispectral imaging to map covered paints

    Directory of Open Access Journals (Sweden)

    Antonino Cosentino

    2016-01-01

    Full Text Available Transmitted spectroscopy and transmitted multispectral imaging in the 400-900 nm range have been applied for the mapping and tentative identification of paints covered by a white preparation as in the case of a ground laid for reusing a canvas for another painting. These methods can be applied to polychrome works of art, as long as their support and new preparation are sufficiently translucent. This work presents the transmittance spectra acquired from a test board consisting of a prepared canvas with swatches of 54 pigments covered with titanium white and the multispectral images realized with transmitted light to map covered paints on a mock-up painting. It was observed that 18 out of 54 historical pigments provide characteristic transmittance spectra even underneath a titanium white preparation layer and that transmitted light multispectral imaging can map hidden paint layers.

  9. Large-Scale Quantitative Analysis of Painting Arts

    Science.gov (United States)

    Kim, Daniel; Son, Seung-Woo; Jeong, Hawoong

    2014-12-01

    Scientists have made efforts to understand the beauty of painting art in their own languages. As digital image acquisition of painting arts has made rapid progress, researchers have come to a point where it is possible to perform statistical analysis of a large-scale database of artistic paints to make a bridge between art and science. Using digital image processing techniques, we investigate three quantitative measures of images - the usage of individual colors, the variety of colors, and the roughness of the brightness. We found a difference in color usage between classical paintings and photographs, and a significantly low color variety of the medieval period. Interestingly, moreover, the increment of roughness exponent as painting techniques such as chiaroscuro and sfumato have advanced is consistent with historical circumstances.

  10. Observations on bucket foundations under cyclic loading in dense saturated sand

    DEFF Research Database (Denmark)

    Foglia, Aligi; Ibsen, Lars Bo; Nicolai, Giulio

    2014-01-01

    for each test. The discus¬sion of the results focuses on three aspects: a critical cyclic loading configuration isfound and compared with a previous study, a limit value of cyclic moment for which no degenerative rotation occurs is obtained and the effect of the loading frequency on the plastic......-term cyclic response of this foundation is not fully understood. In this article, a single gravity physical model is described, an experimental campaign is presented and the observed results are discussed. The aim of the study is to explore the general pattern of response of the foundation under cyclic...

  11. Non-invasive in situ Examination of Colour Changes of Blue Paints in Danish Golden Age Paintings

    DEFF Research Database (Denmark)

    Buti, David; Vila, Anna; Filtenborg, Troels Folke

    A non-invasive study of some paintings containing areas of paint with a Prussian blue component has been conducted at the Statens Museum for Kunst. The in situ campaign has been carried out with a range of different spectroscopic portable techniques, provided by the MOLAB transnational access wit...

  12. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED...

  13. CHARACTERIZATION OF LOW-VOC LATEX PAINTS: VOLATILE ORGANIC COMPOUND CONTENT, VOC AND ALDEHYDE EMISSIONS, AND PAINT PERFORMANCE

    Science.gov (United States)

    The report gives results of laboratory tests to evaluate commercially available latex paints advertised as "low-odor," "low-VOC (volatile organic compound)," or "no-VOC." Measurements were performed to quantify the total content of VOCs in the paints...

  14. CAPSTONE REPORT ON THE DEVELOPMENT OF A STANDARD TEST METHOD FOR VOC EMISSIONS FROM INTERIOR LATEX PAINT AND ALKYD PAINTS

    Science.gov (United States)

    The report gives details of a small-chamber test method developed by the EPA for characterizing volatile organic compound (VOC) emissions from interior latex and alkyd paints. Current knowledge about VOC, including hazardous air pollutant, emissions from interior paints generated...

  15. Plastic Pollution from Ships

    OpenAIRE

    Čulin, Jelena; Bielić, Toni

    2016-01-01

    The environmental impact of shipping on marine environment includes discharge of garbage. Plastic litter is of particular concern due to abundance, resistance to degradation and detrimental effect on marine biota. According to recently published studies, a further research is required to assess human health risk. Monitoring data indicate that despite banning plastic disposal at sea, shipping is still a source of plastic pollution. Some of the measures to combat the problem are discussed.

  16. Neutron Reference Benchmark Field Specifications: ACRR Polyethylene-Lead-Graphite (PLG) Bucket Environment (ACRR-PLG-CC-32-CL).

    Energy Technology Data Exchange (ETDEWEB)

    Vega, Richard Manuel [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Parm, Edward J. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Griffin, Patrick J. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Vehar, David W. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-07-01

    This report was put together to support the International Atomic Energy Agency (IAEA) REAL- 2016 activity to validate the dosimetry community’s ability to use a consistent set of activation data and to derive consistent spectral characterizations. The report captures details of integral measurements taken in the Annular Core Research Reactor (ACRR) central cavity with the Polyethylene-Lead-Graphite (PLG) bucket, reference neutron benchmark field. The field is described and an “a priori” calculated neutron spectrum is reported, based on MCNP6 calculations, and a subject matter expert (SME) based covariance matrix is given for this “a priori” spectrum. The results of 37 integral dosimetry measurements in the neutron field are reported.

  17. Neurotoxic effects of organic solvents among workers in paint and lacquer manufacturing industry

    Directory of Open Access Journals (Sweden)

    Jovanović Jovica M.

    2004-01-01

    Full Text Available Introduction Organic solvents are chemically different compounds with one common feature: they dissolve fats, oils, resins, cellulose acetate and cellulose nitrate, which makes them widely used in industry. Most often organic solvents are used in paint and lacquer industries, in production of pesticides, plastics, explosives, rubber, cellulose, air conditioners, in pharmaceutical industry and in leather industry. The aim of this research was to analyze the working environment and professional hazards in paint and lacquer manufacturing industry and evaluate effects of chronic exposure to mixture of organic solvents on nervous system of exposed workers. Methodology The exposed group consisted of 50 workers professionally exposed to these noxae, while the control group consisted of 30 workers who have never been exposed to these noxae. Results Examination of working environment in departments of paint and lacquer manufacturing revealed presence of white spirit and toluene above allowed levels. Exposed workers more frequently complained of fatigue, hand numbness, enhanced excitation, and concentration difficulties, forgetfulness and headaches, than workers from the control group. Electroneurographic examination of n. medianus showed reduced motor and sensitive conduction velocity among exposed in comparison to workers from the control group. Reduced motor and sensitive conduction velocity was correlated with duration of exposure to these noxae. Terminal latency of n. medianus was statistically, significantly longer in the exposed group than in the control group. Workers in the exposed group have statistically significantly longer reaction time in response to acoustic and visual stimuli. Discussion Segmental demyelination and axonal degeneration, as forms of damage to peripheral nerves, were identified as responsible for peripheral neuropathy associated with occupational exposure to organic solvents. Conclusion Results of this study show possible

  18. Handbook of Plastic Welding

    DEFF Research Database (Denmark)

    Islam, Aminul

    The purpose of this document is to summarize the information about the laser welding of plastic. Laser welding is a matured process nevertheless laser welding of micro dimensional plastic parts is still a big challenge. This report collects the latest information about the laser welding of plasti...... as a knowledge handbook for laser welding of plastic components. This document should provide the information for all aspects of plastic laser welding and help the design engineers to take all critical issues into consideration from the very beginning of the design phase....

  19. Plastics and health risks.

    Science.gov (United States)

    Halden, Rolf U

    2010-01-01

    By 2010, the worldwide annual production of plastics will surpass 300 million tons. Plastics are indispensable materials in modern society, and many products manufactured from plastics are a boon to public health (e.g., disposable syringes, intravenous bags). However, plastics also pose health risks. Of principal concern are endocrine-disrupting properties, as triggered for example by bisphenol A and di-(2-ethylhexyl) phthalate (DEHP). Opinions on the safety of plastics vary widely, and despite more than five decades of research, scientific consensus on product safety is still elusive. This literature review summarizes information from more than 120 peer-reviewed publications on health effects of plastics and plasticizers in lab animals and humans. It examines problematic exposures of susceptible populations and also briefly summarizes adverse environmental impacts from plastic pollution. Ongoing efforts to steer human society toward resource conservation and sustainable consumption are discussed, including the concept of the 5 Rs--i.e., reduce, reuse, recycle, rethink, restrain--for minimizing pre- and postnatal exposures to potentially harmful components of plastics.

  20. Synaptic Plasticity and Nociception

    Institute of Scientific and Technical Information of China (English)

    ChenJianguo

    2004-01-01

    Synaptic plasticity is one of the fields that progresses rapidly and has a lot of success in neuroscience. The two major types of synaptie plasticity: long-term potentiation ( LTP and long-term depression (LTD are thought to be the cellular mochanisms of learning and memory. Recently, accumulating evidence suggests that, besides serving as a cellular model for learning and memory, the synaptic plasticity involves in other physiological or pathophysiological processes, such as the perception of pain and the regulation of cardiovascular system. This minireview will focus on the relationship between synaptic plasticity and nociception.

  1. AUTOMATED DYNAMIC LOAD CONTROL BY ELECTROMECHANICAL SYSTEMS OF A BUCKET-CHAIN EXCAVATOR IN THE COURSE OF SCOOPING

    Directory of Open Access Journals (Sweden)

    Khayrullin Rustam Zinnatullovich

    2012-10-01

    Full Text Available Methods and algorithms of control of the tension of lifting and towing ropes of bucket-chain excavators are proposed in the article. They are based on the non-linear dependence of the current path length and intensity of excavation efforts. Three automatic control modes, including scooping, correction signals and automatic overload protection, are implemented. Two independent control loops in charge of tension of lifting and towing ropes are developed. The proposed automated control system may be integrated both into new bucket-chain excavators and into those excavators that are already in operation. The new system does not require any substantial alterations in electric drive control systems in charge of lifting and towing, if integrated into excavators in operation. The author has performed the non-linearity analysis; he has also designed, developed and implemented the models that are capable of taking an adequate account of the system peculiarities identified in the course of the project implementation. The system parameters are adjustable to specific conditions of the excavator operation, including the hardness of the rock extracted by the excavator, etc. The automatic overload control system attached to the electric drives in control of lifting and towing ensures maximal responsiveness of the system based on the commutation-related limitations imposed by power-driven elements, maximal over-control values and variability of the transition process. Prevention of any rope slacks in the course of scooping of any hard rock is assured by the loop of regulation of minimal tension of lifting cables. The service life of lifting and towing ropes goes up by eight to ten weeks, if the system proposed by the author is implemented.

  2. Scientific Basis for Paint Stripping: Elucidated Combinatorial Mechanism of Methylene Chloride and Phenol Based Paint Removers

    Science.gov (United States)

    2014-01-22

    Polyurethane 31 Cobalt titanate spinel 0.4 Dispersant 1 Methyl isoamyl ketone 23.5 Rheology modifier 0.1 VM&P naptha 3.2 Flow modifier ɘ.1 Xylene...partial formulation films, with pigments and no fillers, and full formulation films of current military polyurethane coatings were analyzed in this...time of the solvents. 22-01-2014 Memorandum Report Paint stripper Methylene chloride Phenol Polyurethane 7 June 2012 – 6 June 2013 SERDP WP-2244

  3. Diuretic plants in the paintings of Pompeii.

    Science.gov (United States)

    Melillo, L

    1994-01-01

    The plants that appear in the paintings and mosaics of Pompeii are chiefly edible and medicinal, though flowers with purely esthetic appeal are also shown. An important example is one of the floor mosaics from the House of the Faun, in which it is possible to identify lemon, cherry, strawberry, pomegranate, grape and olive, leaves of grape, fig, apple and olive, and flowers of corn cockle. The diuretic properties of some of these plants are mentioned in the Naturalis Historia of Pliny the Elder. A silver cup from the House of Menandro, one of the most refined examples of plant decoration in antiquity, shows olive branches and fruits. The presence of plants in such artefacts confirms that people of classical times were conscious that plants were important producers of food, oils, fibers, woods and medicines.

  4. Ikuo Hirayama Painting Exhibition Held in Beijing

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>To celebrate the 30th anniversary of the signing of the Sino-Japanese Peace and Friendship Treaty, the Ikuo Hirayama Painting Exhibition jointly sponsored by the China-Japan Friendship Association (CJFA), the China International Culture Association (CICA) and the Japan-China Friendship Association (JCFA), was held in the National Art Museum of China from April 17 to 26. At the invitation of the CJFA, Tomiichi Murayama, former Japanese prime minister, and Ikuo Hirayama, president of the JCFA and famous painter, who led a delegation of over 200 people of various circles, paid a visit to China to attend the opening ceremony of the exhibition and take part in the relevant activities from April 16 to 20.

  5. Digit ratio, color polymorphism and egg testosterone in the Australian painted dragon.

    Directory of Open Access Journals (Sweden)

    Michael Tobler

    Full Text Available Variation in exposure to sex hormones during early development contributes to phenotypic plasticity in vertebrate offspring. As a proposed marker for prenatal sex hormone exposure and because of their association with various physiological and behavioral characteristics, digit ratio and/or digit length have received notable interest within the field of evolutionary ecology. However, the validity of digit measures as a proxy of prenatal sex hormone exposure is controversial and only few studies have provided direct evidence for the link between digit development and prenatal sex hormones. Here, we report morph- and sex-specific variation in digit ratio in wild painted dragon lizards (Ctenophorus pictus. Lizards expressing a yellow bib have significantly larger third-to-fourth toe ratios (3D:4D than lizards without a bib. Males have significantly smaller 3D:4D than females. Furthermore, we show that experimental elevation of yolk testosterone significantly increases 3D:4D in hatchling painted dragon lizards, but has no influence on hatchling size. Our results provide direct and indirect evidence for the involvement of prenatal sex steroids in digit development and it is suggested that digit ratio may be used as a biomarker for prenatal steroid exposure in this reptilian species. As such, digit ratio may provide a useful tool to study temporal or spatial differences in the proximate hormonal mechanisms modulating physiological and behavioural phenotypes.

  6. Judgement of paintings belonging to different tendencies in the 20th century painting

    Directory of Open Access Journals (Sweden)

    Radonjić Ana

    2004-01-01

    Full Text Available In this study Trifunović’ hypothesis that there are three objective lines in the development of modern art was psychologically evaluated. According to Trifunović, in the first line (Cézanne - cubism - neoplasticism - suprematism the geometrization of form prevails, in the second (Van Gogh - expressionism - abstract expressionism the use of color is dominant, whereas the main features of the third line (Gauguin - fauvism are symbolic use of color and reduction of perspective. Fifteen reproductions of paintings that represent the three developmental lines were used as stimuli. The subjects were asked to judge the stimuli on nine bipolar 7-step scales. These scales constitute the three factors of instrument SDF 9: Evaluation, Arousal and Regularity (3 scales x 3 factors = 9 scales. Four clusters of paintings were obtained: Abstract-expressionistic (moderate Evaluation, high Arousal and low Regularity, Figural-expressionistic (very low Evaluation, low Arousal and high Regularity, Constructivistic (moderate Evaluation, low Arousal and high Regularity and Realistic (high Evaluation, high Arousal and high Regularity. The results partially confirm Trifunović’ hypothesis indicating that, besides the formal features, the content (abstract vs. figural is also significant factor of subjective clustering of paintings.

  7. Paint removal and surface cleaning using ice particles

    Science.gov (United States)

    Foster, Terry; Visaisouk, S.

    1995-04-01

    Research into the possibility of using ice particles as a blast medium was first initiated at Defence Research Establishment Pacific (DREP) in an effort to develop a more environmentally acceptable paint removal method. A paint removal process was also required that could be used in areas where normal grit blasting could not be used due to the possibility of the residual blasting grit contaminating machinery and other equipment. As a result of this research a commercial ice blasting system was developed by RETECH. This system is now being used to remove paint from substrates that cannot be easily blasted by conventional techniques and also to clean soiled or contaminated surfaces. The problems involved in the development of an ice blast system and its components and their functions are described. Due to the complexity of paint removal using ice blasting, parameters such as air pressure, ice particle size and ice particle flow rate were studied and adjusted to suit the nature of the particular coating and substrate of interest. The mechanism of paint removal by ice particles has also been investigated. A theoretical model has been developed to explain the different paint removal mechanisms such as erosion by abrasion and erosion by fracture as they relate to ice blasting. Finally, the use of ice blasting to removal paint from a variety of substrates is presented as well as examples of surface cleaning and surface decontamination.

  8. Investigation on the hazing of a Brazilian contemporary painting

    Science.gov (United States)

    Puglieri, Thiago S.; Lavezzo, Ariane S.; Santos, Isabela F. S. dos; de Faria, Dalva L. A.

    2016-04-01

    A whitish crystalline-like coating was observed on the surface of the painting "Incêndio", 1990, produced by Emmanuel Nassar and awarded at the 6th Biennial of Cuenca. This work belongs to the Contemporary Art Museum of the University of São Paulo (MAC-USP) and such coating modified the artwork characteristics, causing an unpleasant effect and compromising its exhibition. The choice of the proper conservation and restoration strategies involves the understanding of the degradation process, demanding the identification of the chemical compounds formed on the painting surface, as well as of the other components in the painting. The results here obtained from Raman and optical microscopies, FTIR-ATR, SEM-EDS and GC-MS, revealed that the efflorescence chemical composition is almost only palmitic acid, with minor contents of stearic acid and their methyl esters, and that the paints are composed by chrome yellow, amorphous carbon and toluidine red pigment; an aluminum silicate filler in the black paint applied on the aluminum ground was also detected. Hierarchical Cluster Analyses (HCA) of the Raman spectra also revealed that the concentration of the efflorescence minor components depends on the paint composition. It was suggested, therefore, that the degradation process resulted from segregation and migration of mainly palmitic acid from the dried paints. Restoration methodologies used in similar cases, as well as factors that contribute to this process, were discussed.

  9. A study on impact monitoring using a piezoelectric paint sensor

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Kyung Woo; Kang, Dong Hoon [Korea Railroad Research Institute, Uiwang (Korea, Republic of); Park, Seung Bok; Kang, Lae Hyong [Chonbuk National University, Jeonju (Korea, Republic of)

    2015-10-15

    The piezoelectric paint sensor is a paint type sensor comprising of an epoxy and piezoelectric powder, which is the main component of a piezoelectric material. This sensor can be easily attached to any type of structure as compared to other sensors because it is viable to directly apply it on structures, as in the case with a typical paint. In this study, the capability of piezoelectric paint sensor for impact detection was evaluated. In Particular, the applications of the piezoelectric paint sensor for railroad vehicles were considered. There have been various cases reported about the damages caused by flying gravel to the under-cover of the railroad vehicle during operation. In order to prevent this, real-time monitoring of the large under-cover surface of the railroad vehicle is unavoidable. Under the assumption of vehicle application, sensor sensitivities were measured after multiple and prolonged exposure to thermal cycle environment -20⁓60 degrees Celsius). Sensitivity evaluation of paint sensor under environmental conditions was conducted in an aluminum specimen. In results, despite the small variations in sensitivity, we could confirm the applicability of this paint sensor for impact detection even after a severe environmental exposure test.

  10. Comparable Outcomes After Bucket-Handle Meniscal Repair and Vertical Meniscal Repair Can Be Achieved at a Minimum 2 Years' Follow-up.

    Science.gov (United States)

    Moatshe, Gilbert; Cinque, Mark E; Godin, Jonathan A; Vap, Alexander R; Chahla, Jorge; LaPrade, Robert F

    2017-08-01

    Meniscal tears can lead to significant pain and disability, necessitating surgical treatment. Nondisplaced vertical tears are usually smaller in size and can be repaired in most cases; however, bucket-handle tears are usually larger and displaced, and the repair of these tears can be challenging. Purpose/Hypothesis: The purpose was to report the outcomes after inside-out vertical mattress suture meniscal repair of bucket-handle tears and to compare these outcomes with those of patients who underwent repair of nondisplaced vertical meniscal tears with a minimum of 2 years' follow-up. The hypothesis was that the outcomes of bucket-handle tear repair would be comparable with those of nondisplaced vertical meniscal tear repair. Cohort study; Level of evidence, 3. Patients who underwent inside-out repair of a bucket-handle meniscal tear or a nondisplaced vertical meniscal tear with a minimum 2 years' follow-up were included in this study. Patients were excluded if they had a diagnosis of a meniscal root tear, underwent a concomitant procedure for a chondral injury, or underwent previous surgical treatment of the same meniscus. Subjective questionnaires were administered preoperatively and postoperatively, including the Lysholm score, the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), the Short Form-12 (SF-12) physical component summary (PCS) and mental component summary (MCS), the Tegner activity scale, and patient satisfaction. Thirty-two patients underwent repair for vertical meniscal tears (mean, 7 sutures), while 38 patients underwent repair for bucket-handle meniscal tears (mean, 11 sutures), with a mean follow-up of 3.1 years (range, 2-6 years). There were no significant differences in the preoperative outcome scores between the 2 groups. Significant improvements in patient-reported outcome scores from preoperatively to postoperatively were found in both groups. A direct comparison of the bucket-handle tear group to the vertical tear group

  11. Clay ground in paintings: from Northern to Southern Europe

    DEFF Research Database (Denmark)

    Buti, David; Vila, Anna; Haack Christensen, Anne

    it give more flexibility to the painting support? Was it connected to the tile industry? Was it a waste/reuse from the ceramic production? To better understand the role of clay ground as a material and its influence on painting techniques, a number of Danish and Italian 17th century paintings from...... of the period, the transmission of technology and knowledge of employing this type of clay grounds and, possibly, tracing the origin of the raw materials employed in the grounds. [1] K. M. Groen, ArtMatters - Netherlands Technical Studies in Art, 3, 2005, 138-154. Waanders, Zwolle. [2] K. M. Groen, "Grounds...

  12. Trends in the automotive paint industry for corrosion protection

    Energy Technology Data Exchange (ETDEWEB)

    Blandin, Nathalie; Brunat, William [PPG Industries France, 3 Z.A.E. Les Dix Muids, B.P. 89, F-59583 Marly (France); Neuhaus, Ralf [PPG Industries Lacke GmbH, Stackenbergstrasse 34, D-42329 Wuppertal (Germany); Sibille, Ettore [PPG Industries Italia, Via Serra11, I-15028 Quattordio (Italy)

    2004-07-01

    Since many years ED-paints are protecting car bodies against corrosion. Currently the automotive paint industry is faced with increasing demands of higher levels of corrosion protection and also requests to comply with new environmental regulations and economical pressures. Some key factors that contributed significantly towards the improvement of corrosion protection systems are: - New generations of lead free ED-paints; - Weldable organic thin film for corrosion protection, especially in box cavities and flange areas. The goal of this paper is to show how the various elements of the 'anti-corrosion package' interact. (authors)

  13. Multispectral infrared reflectography to differentiate features in paintings.

    Science.gov (United States)

    Daffara, Claudia; Fontana, Raffaella

    2011-10-01

    Infrared reflectography is a well-known technique based on wideband imaging in the near-infrared (NIR) range used for painting diagnostics in conservation laboratories.. This work is focused on the application of multiband reflectography for analysis of pictorial layers and differentiated detection of painting features. This technique generates a set of narrowband NIR images of the painting. Starting from a dataset that is registered, metrically correct, and calibrated, the capability of collecting both spectral and spatial information has been exploited by processing the image cube with interplane techniques. Examples on artworks by Caravaggio, Veronese, Bronzino, and Schiavone are presented.

  14. An environmentally safe and effective paint removal process for aircraft

    Science.gov (United States)

    Kozol, Joseph

    2001-03-01

    To reduce hazardous waste from fleet and depot aircraft paint stripping and to conform to regulations banning toxic chemical paint strippers, the U.S. Naval Air Systems Team (materials division, depots, and head-quarters) teamed with the U.S. Air Force at Warner Robins Air Logistics Center for concept development, characterization, and demonstration of a mature, advanced paint-removal system, the Boeing xenon/flashlamp CO2 (Flashjet®) process. Extensive metallic and composite-materials testing was conducted. This paper describes the development and characterization program leading to authorization of the process for use on fixed-wing navy aircraft.

  15. PMT signal increase using a wavelength shifting paint

    CERN Document Server

    Allada, K; Ou, L; Schmookler, B; Shahinyan, A; Wojtsekhowski, B

    2015-01-01

    We report a 1.65 times increase of the PMT signal and a simple procedure of application of a new wavelength shifting (WLS) paint for PMTs with non-UV-transparent windows. Samples of four different WLS paints, made from hydrocarbon polymers and organic fluors, were tested on a 5-inch PMT (ET 9390KB) using Cherenkov radiation produced in fused silica disks by $^{106}$Ru electrons on a `table-top' setup. The best performing paint was employed on two different types of 5-inch PMTs (ET 9390KB and XP4572B), installed in atmospheric pressure CO$_2$ gas Cherenkov detectors, and tested using GeV electrons.

  16. Analytical studies of the Alexandrovo Thracian tomb wall paintings

    Science.gov (United States)

    Glavcheva, Z.; Yancheva, D.; Velcheva, E.; Stamboliyska, B.; Petrova, N.; Petkova, V.; Lalev, G.; Todorov, V.

    2016-01-01

    A profound study of samples obtained from Thracian tomb wall paintings at Alexandrovo, Bulgaria (dating back to the fourth century BC) were carried out by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR) and Attenuated Total Reflectance Fourier transform infrared spectroscopy (ATR FTIR), high-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (EDS). The current work provides a glimpse of the ingenious construction and painting techniques used in Thracian tomb at Alexandrovo. The results suggest that beeswax was used as a paint binder and also revealed presence of various nano-materials.

  17. Study of multilayers by PIXE technique. Application to paintings

    Science.gov (United States)

    Brissaud, Ivan; Lagarde, Gérard; Midy, Pierre

    1996-08-01

    In this article we propose the application of a new algorithm to determine the concentration profile of colour pigments in painting. This is performed by PIXE technique at different proton energies. The algorithm is based on the singular value decomposition of the matrix obtained by discretization of the integral equation for the concentration profile. To check this method, many paint multilayers of acrylic colours were prepared. First results obtained from different experiments at the AGLAE accelerator in the Palais du Louvre at Paris are presented: the nature and the thickness of each colour layer were determined with a good agreement. The analysis of easel paintings is in progress.

  18. The female images in the tang dynasty painting

    Institute of Scientific and Technical Information of China (English)

    靳丽霞

    2014-01-01

    the tang dynasty is the most prosperous dynasties in ancient China. Both in the cultural, economic, political and artistic performance is very outstanding. Historical development of the era makes unprece-dented open people's minds, such open also natural y seep into the woman's behavior, they have a certain personal freedom and individuality liberation, the status of women is rising. This painting in the tang dy-nasty has very good reflected in the female image. At times like these, had appeared Zhang Xuan, zhou-fang painter, their painting art has ex-erts a far-reaching influence on the later tang dynasty figure painting.

  19. Method for simulating paint mixing on computer monitors

    Science.gov (United States)

    Carabott, Ferdinand; Lewis, Garth; Piehl, Simon

    2002-06-01

    Computer programs like Adobe Photoshop can generate a mixture of two 'computer' colors by using the Gradient control. However, the resulting colors diverge from the equivalent paint mixtures in both hue and value. This study examines why programs like Photoshop are unable to simulate paint or pigment mixtures, and offers a solution using Photoshops existing tools. The article discusses how a library of colors, simulating paint mixtures, is created from 13 artists' colors. The mixtures can be imported into Photoshop as a color swatch palette of 1248 colors and as 78 continuous or stepped gradient files, all accessed in a new software package, Chromafile.

  20. Pigeons can discriminate "good" and "bad" paintings by children.

    Science.gov (United States)

    Watanabe, Shigeru

    2010-01-01

    Humans have the unique ability to create art, but non-human animals may be able to discriminate "good" art from "bad" art. In this study, I investigated whether pigeons could be trained to discriminate between paintings that had been judged by humans as either "bad" or "good". To do this, adult human observers first classified several children's paintings as either "good" (beautiful) or "bad" (ugly). Using operant conditioning procedures, pigeons were then reinforced for pecking at "good" paintings. After the pigeons learned the discrimination task, they were presented with novel pictures of both "good" and "bad" children's paintings to test whether they had successfully learned to discriminate between these two stimulus categories. The results showed that pigeons could discriminate novel "good" and "bad" paintings. Then, to determine which cues the subjects used for the discrimination, I conducted tests of the stimuli when the paintings were of reduced size or grayscale. In addition, I tested their ability to discriminate when the painting stimuli were mosaic and partial occluded. The pigeons maintained discrimination performance when the paintings were reduced in size. However, discrimination performance decreased when stimuli were presented as grayscale images or when a mosaic effect was applied to the original stimuli in order to disrupt spatial frequency. Thus, the pigeons used both color and pattern cues for their discrimination. The partial occlusion did not disrupt the discriminative behavior suggesting that the pigeons did not attend to particular parts, namely upper, lower, left or right half, of the paintings. These results suggest that the pigeons are capable of learning the concept of a stimulus class that humans name "good" pictures. The second experiment showed that pigeons learned to discriminate watercolor paintings from pastel paintings. The subjects showed generalization to novel paintings. Then, as the first experiment, size reduction test