WorldWideScience

Sample records for plasma synthetic jet

  1. Experimental Characterization of the Plasma Synthetic Jet Actuator

    Science.gov (United States)

    Jin, Di; Li, Yinghong; Jia, Min; Song, Huimin; Cui, Wei; Sun, Quan; Li, Fanyu

    2013-10-01

    The plasma synthetic jet is a novel active flow control method because of advantages such as fast response, high frequency and non-moving parts, and it has received more attention recently, especially regarding its application to high-speed flow control. In this paper, the experimental characterization of the plasma synthetic jet actuator is investigated. The actuator consists of a copper anode, a tungsten cathode and a ceramic shell, and with these three parts a cavity can be formed inside the actuator. A pulsed-DC power supply was adopted to generate the arc plasma between the electrodes, through which the gas inside was heated and expanded from the orifice. Discharge parameters such as voltage and current were recorded, respectively, by voltage and current probes. The schlieren system was used for flow visualization, and jet velocities with different discharge parameters were measured. The schlieren images showed that the strength of plasma jets in a series of pulses varies from each other. Through velocity measurement, it is found that at a fixed frequency, the jet velocity hardly increases when the discharge voltage ranges from 16 kV to 20 kV. However, with the discharge voltage fixed, the jet velocity suddenly decreases when the pulse frequency rises above 500 Hz, whereas at other testing frequencies no such decrease was observed. The maximum jet velocity measured in the experiment was up to 110 m/s, which is believed to be effective for high-speed flow control.

  2. Geometry optimization of linear and annular plasma synthetic jet actuators

    Science.gov (United States)

    Neretti, G.; Seri, P.; Taglioli, M.; Shaw, A.; Iza, F.; Borghi, C. A.

    2017-01-01

    The electrohydrodynamic (EHD) interaction induced in atmospheric air pressure by a surface dielectric barrier discharge (DBD) actuator has been experimentally investigated. Plasma synthetic jet actuators (PSJAs) are DBD actuators able to induce an air stream perpendicular to the actuator surface. These devices can be used in the field of aerodynamics to prevent or induce flow separation, modify the laminar to turbulent transition inside the boundary layer, and stabilize or mix air flows. They can also be used to enhance indirect plasma treatment effects, increasing the reactive species delivery rate onto surfaces and liquids. This can play a major role in plasma processing and chemical kinetics modelling, where often only diffusive mechanisms are considered. This paper reports on the importance that different electrode geometries can have on the performance of different PSJAs. A series of DBD aerodynamic actuators designed to produce perpendicular jets has been fabricated on two-layer printed circuit boards (PCBs). Both linear and annular geometries were considered, testing different upper electrode distances in the linear case and different diameters in the annular one. An AC voltage supplied at a peak of 11.5 kV and a frequency of 5 kHz was used. Lower electrodes were connected to the ground and buried in epoxy resin to avoid undesired plasma generation on the lower actuator surface. Voltage and current measurements were carried out to evaluate the active power delivered to the discharges. Schlieren imaging allowed the induced jets to be visualized and gave an estimate of their evolution and geometry. Pitot tube measurements were performed to obtain the velocity profiles of the PSJAs and to estimate the mechanical power delivered to the fluid. The optimal values of the inter-electrode distance and diameter were found in order to maximize jet velocity, mechanical power or efficiency. Annular geometries were found to achieve the best performance.

  3. Analytic model and frequency characteristics of plasma synthetic jet actuator

    Science.gov (United States)

    Zong, Hao-hua; Wu, Yun; Li, Ying-hong; Song, Hui-min; Zhang, Zhi-bo; Jia, Min

    2015-02-01

    This paper reports a novel analytic model of a plasma synthetic jet actuator (PSJA), considering both the heat transfer effect and the inertia of the throat gas. Both the whole cycle characteristics and the repetitive working process of PSJA can be predicted with this model. The frequency characteristics of a PSJA with 87 mm3 volume and different orifice diameters are investigated based on the analytic model combined with experiments. In the repetitive working mode, the actuator works initially in the transitional stage with 20 cycles and then in the dynamic balanced stage. During the transitional stage, major performance parameters of PSJA experience stepped growth, while during the dynamic balanced stage, these parameters are characterized by periodic variation. With a constant discharge energy of 6.9 mJ, there exists a saturated frequency of 4 kHz/6 kHz for an orifice diameter of 1 mm/1.5 mm, at which the time-averaged total pressure of the pulsed jet reaches a maximum. Between 0.5 mm and 1.5 mm, a larger orifice diameter leads to a higher saturated frequency due to the reduced jet duration time. As the actuation frequency increases, both the time-averaged cavity temperature and the peak jet velocity initially increase and then remain almost unchanged at 1600 K and 280 m/s, respectively. Besides, with increasing frequency, the mechanical energy incorporated in single pulsed jet, the expelled mass per pulse, and the time-averaged density in the cavity, decline in a stair stepping way, which is caused by the intermittent decrease of refresh stage duration in one period.

  4. Characterisation of plasma synthetic jet actuators in quiescent flow

    Science.gov (United States)

    Zong, Haohua; Kotsonis, Marios

    2016-08-01

    An experimental characterisation study of a large-volume three-electrode plasma synthetic jet actuator (PSJA) is presented. A sequential discharge power supply system is used to activate the PSJA. Phase-locked planar particle image velocimetry (PIV) and time-resolved Schlieren imaging are used to characterise the evolution of the induced flow field in quiescent flow conditions. The effect of orifice diameter is investigated. Results indicate three distinct features of the actuator-induced flow field. These are the initial shock waves, the high speed jet and vortex rings. Two types of shock waves with varied intensities, namely a strong shock wave and a weak shock wave, are issued from the orifice shortly after the ignition of the discharge. Subsequently, the emission of a high speed jet is observed, reaching velocities up to 130 m s-1. Pronounced oscillation of the exit velocity is caused by the periodical behaviour of capacitive discharge, which also led to the formation of vortex ring trains. Orifice diameter has no influence on the jet acceleration stage and the peak exit velocity. However, a large orifice diameter results in a rapid decline of the exit velocity and thus a short jet duration time. Vortex ring propagation velocities are measured at peak values ranging from 55 m s-1-70 m s-1. In the case of 3 mm orifice diameter, trajectory of the vortex ring severely deviates from the actuator axis of symmetry. The development of this asymmetry in the flow field is attributed to asymmetry in the electrode configuration.

  5. Transient ejection phase modeling of a Plasma Synthetic Jet actuator

    Science.gov (United States)

    Laurendeau, F.; Chedevergne, F.; Casalis, G.

    2014-12-01

    For several years, a promising Plasma Synthetic Jet actuator for high-speed flow control has been under development at ONERA. So far, its confined geometry and small space-time scales at play have prevented its full experimental characterization. Complementary accurate numerical simulations are then considered in this study in order to provide a complete aerothermodynamic description of the actuator. Two major obstacles have to be overcome with this approach: the modeling of the energy deposited by the electric arc and the accurate computation of the transient response of the cavity generating the pulsed jet. To solve the first problem, an Euler solver coupled with an electric circuit model was used to evaluate the energy deposition in the cavity. Such a coupling is performed by considering the electric field between the two electrodes. The second issue was then addressed by injecting these source terms in large Eddy simulations of the entire actuator. Aerodynamic results were finally compared with Schlieren visualizations. Using the proposed methodology, the temporal evolution of the jet front is remarkably well predicted.

  6. Characteristics of pulsed plasma synthetic jet and its control effect on supersonic flow

    Institute of Scientific and Technical Information of China (English)

    Jin Di; Cui Wei; Li Yinghong; Li Fanyu; Jia Min; Sun Quan; Zhang Bailing

    2015-01-01

    The plasma synthetic jet is a novel flow control approach which is currently being stud-ied. In this paper its characteristic and control effect on supersonic flow is investigated both exper-imentally and numerically. In the experiment, the formation of plasma synthetic jet and its propagation velocity in quiescent air are recorded and calculated with time resolved schlieren method. The jet velocity is up to 100 m/s and no remarkable difference has been found after chang-ing discharge parameters. When applied in Mach 2 supersonic flow, an obvious shockwave can be observed. In the modeling of electrical heating, the arc domain is not defined as an initial condition with fixed temperature or pressure, but a source term with time-varying input power density, which is expected to better describe the influence of heating process. Velocity variation with different heat-ing efficiencies is presented and discussed and a peak velocity of 850 m/s is achieved in still air with heating power density of 5.0 · 1012 W/m3. For more details on the interaction between plasma syn-thetic jet and supersonic flow, the plasma synthetic jet induced shockwave and the disturbances in the boundary layer are numerically researched. All the results have demonstrated the control authority of plasma synthetic jet onto supersonic flow.

  7. Characteristics of pulsed plasma synthetic jet and its control effect on supersonic flow

    Directory of Open Access Journals (Sweden)

    Jin Di

    2015-02-01

    Full Text Available The plasma synthetic jet is a novel flow control approach which is currently being studied. In this paper its characteristic and control effect on supersonic flow is investigated both experimentally and numerically. In the experiment, the formation of plasma synthetic jet and its propagation velocity in quiescent air are recorded and calculated with time resolved schlieren method. The jet velocity is up to 100 m/s and no remarkable difference has been found after changing discharge parameters. When applied in Mach 2 supersonic flow, an obvious shockwave can be observed. In the modeling of electrical heating, the arc domain is not defined as an initial condition with fixed temperature or pressure, but a source term with time-varying input power density, which is expected to better describe the influence of heating process. Velocity variation with different heating efficiencies is presented and discussed and a peak velocity of 850 m/s is achieved in still air with heating power density of 5.0 × 1012 W/m3. For more details on the interaction between plasma synthetic jet and supersonic flow, the plasma synthetic jet induced shockwave and the disturbances in the boundary layer are numerically researched. All the results have demonstrated the control authority of plasma synthetic jet onto supersonic flow.

  8. Influence of geometrical parameters on performance of plasma synthetic jet actuator

    Science.gov (United States)

    Zong, Hao-hua; Wu, Yun; Jia, Min; Song, Hui-min; Liang, Hua; Li, Ying-hong; Zhang, Zhi-bo

    2016-01-01

    Plasma synthetic jet actuator (PSJA) has shown wide and promising application prospects in a high speed flow control field, due to its rapid response, high exhaust velocity, and non-moving components. In this paper, the total pressure profile of a plasma synthetic jet (PSJ) is measured and a new method is developed to evaluate the pulsed thrust of the PSJA. The influence of geometrical parameters including the electrode distance, the orifice diameter, and the throat length on PSJA performance is analyzed based on the pulsed thrust, the discharge characteristics, and the schlieren images. When varying the electrode distance, the dominant factor determining the jet intensity is the heating volume instead of the discharge energy. For the arc discharge, the electrode distance should be extended to increase both the jet velocity and the jet duration time. The design of the orifice diameter should be based on the controlled flow field. A large orifice diameter produces a strong perturbation with short time duration, while a small orifice diameter induces a lasting jet with low mass flux. In order to obtain better high frequency performance, the throat length should be shortened on the condition that the structural strength of the PSJA is maintained, while there is almost no influence of the throat length on the single cycle performance of the PSJA. Once the discharge energy is fixed, the pulsed thrust remains almost unchanged with different orifice diameters and throat lengths. These three geometrical parameters are independent to some extent and can be optimized separately.

  9. Influence of the energy dissipation rate in the discharge of a plasma synthetic jet actuator

    Energy Technology Data Exchange (ETDEWEB)

    Belinger, A; Cambronne, J P [Universite de Toulouse, UPS, INPT, LAPLACE - Laboratoire Plasma et Conversion d' Energie, 118 route de Narbonne, F-31062 Toulouse cedex 9 (France); Hardy, P; Barricau, P; Caruana, D, E-mail: daniel.caruana@onera.fr [ONERA Centre Midi-Pyrenees, Departement Modeles pour l' Aerodynamique et l' Energetique, BP74025, 2 avenue Edouard Belin, 31055 TOULOUSE CEDEX 4 (France)

    2011-09-14

    A promising actuator for high-speed flow control, referred to as a plasma synthetic jet (PSJ), is being studied by the DMAE department of the ONERA, and the Laplace laboratory of the CNRS, in France. This actuator was inspired by the 'sparkjet' device developed by the Johns Hopkins University Applied Physics Laboratory. The PSJ, which produces a synthetic jet with high exhaust velocities, no active mechanical components and no mass flow admission, holds the promise of enabling high-speed flows to be manipulated. With this high-velocity jet it is possible to reduce fluid phenomena such as transition and turbulence, thus making it possible to increase an aircraft's performance whilst at the same time reducing its environmental impact. A thermal plasma discharge was created in a micro-cavity, causing the gas to be expelled. It is relevant that the velocity and momentum depend on the energy dispersed by the electric discharge. To control the frequency and energy dispersed in the plasma, the Laplace laboratory has developed two high-voltage power supply systems. These allow two different types of discharge to be produced, with energy being supplied to the discharge in two different manners. In this paper, we focus on the impact of the power supply on the plasma synthetic jet, and in particular on the role of the rate of energy dissipation in the discharge. In order to estimate the influence of the power supply on the machinery of the actuator, specific experimental techniques were used to investigate the electrical (voltage, current), thermal (Infra-red camera) and aerodynamic (jet duration, isentropic pressure, jet velocity) characteristics. These data sets were used to determine which of the two power supplies was more effective, thus allowing us to reach several conclusions concerning the importance of the energy dissipation rate on the PSJ actuator.

  10. Effect of pressure on the performance of plasma synthetic jet actuator

    Science.gov (United States)

    Wang, Lin; Xia, ZhiXun; Luo, ZhenBing; Zhang, Yu

    2014-12-01

    The effects of the ambient air pressure level on the performance of plasma synthetic jet actuator have been investigated through electrical and optical diagnostics. Pressures from 1 atm down to 0.1 atm were tested with a 10 Hz excitation. The discharge measurement demonstrates that there is a voltage range to make the actuator work reliably. Higher pressure level needs a higher breakdown voltage, and a higher discharge current and energy deposition are produced. But when the actuator works with the maximum breakdown voltage, the fraction of the initial capacitor energy delivered to the arc is almost invariable. This preliminary study also confirms the effectiveness of the plasma synthetic jet at low pressure. Indeed, the maximum velocities of the precursor shock and the plasma jet induced by the actuator with maximum breakdown voltage are independent of the ambient pressure level; reach about 530 and 460 m/s respectively. The mass flux of the plasma jet increases with ambient pressure increasing, but the strength of the precursor shock presents a local maximum at 0.6 atm.

  11. Influence of air pressure on the performance of plasma synthetic jet actuator

    Science.gov (United States)

    Li, Yang; Jia, Min; Wu, Yun; Li, Ying-hong; Zong, Hao-hua; Song, Hui-min; Liang, Hua

    2016-09-01

    Plasma synthetic jet actuator (PSJA) has a wide application prospect in the high-speed flow control field for its high jet velocity. In this paper, the influence of the air pressure on the performance of a two-electrode PSJA is investigated by the schlieren method in a large range from 7 kPa to 100 kPa. The energy consumed by the PSJA is roughly the same for all the pressure levels. Traces of the precursor shock wave velocity and the jet front velocity vary a lot for different pressures. The precursor shock wave velocity first decreases gradually and then remains at 345 m/s as the air pressure increases. The peak jet front velocity always appears at the first appearance of a jet, and it decreases gradually with the increase of the air pressure. A maximum precursor shock wave velocity of 520 m/s and a maximum jet front velocity of 440 m/s are observed at the pressure of 7 kPa. The averaged jet velocity in one period ranges from 44 m/s to 54 m/s for all air pressures, and it drops with the rising of the air pressure. High velocities of the precursor shock wave and the jet front indicate that this type of PSJA can still be used to influence the high-speed flow field at 7 kPa. Project supported by the National Natural Science Foundation of China (Grant Nos. 51407197, 51522606, 51336011, 91541120, and 11472306).

  12. Effect of the duty cycle on the spark-plug plasma synthetic jet actuator

    Directory of Open Access Journals (Sweden)

    Seyhan Mehmet

    2016-01-01

    Full Text Available A promising novel actuator called Spark-Plug Plasma Synthetic Jet (SPSJ has been developed in Atmospheric Plasma Research Laboratory at Niğde University. It generates electrothermally high synthetic jet velocity by using high voltage. SPSJ actuator can be utilized to be an active flow control device having some advantages such as no moving parts, low energy consumption and easy to integrate the system. This actuator consists of two main components: semi-surface spark plug (NGK BUHW as an anode electrode and a cap having an orifice as a cathode electrode. The cap, having a jet exit orifice diameter of 2 mm, has diameter of 4.4 mm and height of 4.65 mm. This study presents the characteristics of SPSJ actuator by using the hot wire anemometer in order to approximately determine jet velocity in quiescent air. Peak velocity as high as 180 m/s was obtained for fe= 100 and duty cycle 50%. The flow visualization indicated that the actuator’s jet velocity is enough to penetrate the developed boundary layer.

  13. Multi-chord fiber-coupled interferometry of supersonic plasma jets and comparisons with synthetic data

    CERN Document Server

    Merritt, Elizabeth C; Gilmore, Mark A; Thoma, Carsten; Loverich, John; Hsu, Scott C

    2012-01-01

    A multi-chord fiber-coupled interferometer [Merritt et al., Rev. Sci. Instrum. 83, 033506 (2012)] is being used to make time-resolved density measurements of supersonic argon plasma jets on the Plasma Liner Experiment [Hsu et al., Bull. Amer. Phys. Soc. 56, 307 (2011)]. The long coherence length of the laser (>10 m) allows signal and reference path lengths to be mismatched by many meters without signal degradation, making for a greatly simplified optical layout. Measured interferometry phase shifts are consistent with a partially ionized plasma in which an initially positive phase shift becomes negative when the ionization fraction drops below a certain threshold. In this case, both free electrons and bound electrons in ions and neutral atoms contribute to the index of refraction. This paper illustrates how the interferometry data, aided by numerical modeling, are used to derive total jet density, jet propagation velocity (~15-50 km/s), jet length (~20-100 cm), and 3D expansion.

  14. Jet fuels from synthetic crudes

    Science.gov (United States)

    Antoine, A. C.; Gallagher, J. P.

    1977-01-01

    An investigation was conducted to determine the technical problems in the conversion of a significant portion of a barrel of either a shale oil or a coal synthetic crude oil into a suitable aviation turbine fuel. Three syncrudes were used, one from shale and two from coal, chosen as representative of typical crudes from future commercial production. The material was used to produce jet fuels of varying specifications by distillation, hydrotreating, and hydrocracking. Attention is given to process requirements, hydrotreating process conditions, the methods used to analyze the final products, the conditions for shale oil processing, and the coal liquid processing conditions. The results of the investigation show that jet fuels of defined specifications can be made from oil shale and coal syncrudes using readily available commercial processes.

  15. Dense Hypervelocity Plasma Jets

    Science.gov (United States)

    Case, Andrew; Witherspoon, F. Douglas; Messer, Sarah; Bomgardner, Richard; Phillips, Michael; van Doren, David; Elton, Raymond; Uzun-Kaymak, Ilker

    2007-11-01

    We are developing high velocity dense plasma jets for fusion and HEDP applications. Traditional coaxial plasma accelerators suffer from the blow-by instability which limits the mass accelerated to high velocity. In the current design blow-by is delayed by a combination of electrode shaping and use of a tailored plasma armature created by injection of a high density plasma at a few eV generated by arrays of capillary discharges or sparkgaps. Experimental data will be presented for a complete 32 injector gun system built for driving rotation in the Maryland MCX experiment, including data on penetration of the plasma jet through a magnetic field. We present spectroscopic measurements of plasma velocity, temperature, and density, as well as total momentum measured using a ballistic pendulum. Measurements are in agreement with each other and with time of flight data from photodiodes and a multichannel PMT. Plasma density is above 10^15 cm-3, velocities range up to about 100 km/s. Preliminary results from a quadrature heterodyne HeNe interferometer are consistent with these results.

  16. Jet Vectoring Control Using a Novel Synthetic Jet Actuator

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either "push" or "pull", one novel synthetic jet actuator can fulfill both "push" and "pull" functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various applications, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.

  17. Formation Criterion for Synthetic Jets

    Science.gov (United States)

    2005-10-01

    formation data for the axisymmetric case were published over 50 years ago by Ingard and Labate.10 More recent studies33,34 suggest that L0/d > 1 for...with the axisymmetric data from Ingard and Labate10 and Smith et al.33 are compared in Fig. 7. It is found that the available data are consis- tent with...the jet formation criterion with an empirically determined constant K equal to approximately 0.16. The deviation of Ingard and Labate’s data at their

  18. Supersonic induction plasma jet modeling

    Energy Technology Data Exchange (ETDEWEB)

    Selezneva, S.E. E-mail: svetlana2@hermes.usherbS_Selezneva2@hermes.usherb; Boulos, M.I

    2001-06-01

    Numerical simulations have been applied to study the argon plasma flow downstream of the induction plasma torch. It is shown that by means of the convergent-divergent nozzle adjustment and chamber pressure reduction, a supersonic plasma jet can be obtained. We investigate the supersonic and a more traditional subsonic plasma jets impinging onto a normal substrate. Comparing to the subsonic jet, the supersonic one is narrower and much faster. Near-substrate velocity and temperature boundary layers are thinner, so the heat flux near the stagnation point is higher in the supersonic jet. The supersonic plasma jet is characterized by the electron overpopulation and the domination of the recombination over the dissociation, resulting into the heating of the electron gas. Because of these processes, the supersonic induction plasma permits to separate spatially different functions (dissociation and ionization, transport and deposition) and to optimize each of them. The considered configuration can be advantageous in some industrial applications, such as plasma-assisted chemical vapor deposition of diamond and polymer-like films and in plasma spraying of nanoscaled powders.

  19. PIV Measurements and Mechanisms of Adjacent Synthetic Jets Interactions

    Institute of Scientific and Technical Information of China (English)

    LUO Zhen-Bing; XIA Zhi-Xun

    2008-01-01

    Interactions of adjacent synthetic jet actuators with varying relative amplitude and the relative phase of driving voltage are measured using a particle image velocimetry(PIV).Varying relative amplitude or relative phase of driving voltage of the adjacent actuators vectors the direction of the ensuing merged jet of the adjacent synthetic jets.The vectoring mechanism of the adjacent vortex pairs,attract-impact causing deflection(AICD),is provided to explain why the merged jet is generally vectored to the side of the phase-leading synthetic jet or the synthetic jet with higher driving voltage.

  20. Physical factors of primary jet vectoring control using synthetic jet actuators

    Institute of Scientific and Technical Information of China (English)

    XIA Zhi-xun; LUO Zhen-bing

    2007-01-01

    A primary jet vectoring using synthetic jet actuators with different exit configurations was investigated, and the main physical factors influencing jet vectoring were analyzed and summarized. The physical factors of the pressure difference, the location and area of the lower pressure region, the component of the synthetic jet momentum and the entrainment ratio of the synthetic jet flow to primary jet flow directly control the vectoring force and the vectoring angle. Three characteristic parameters of the synthetic jet contribute to the pressure difference and the area of the lower pressure region Both the extension step and slope angle of the actuator exit have functions of regulating the location of the lower pressure region, the area of the lower pressure region, and the entrainment ratio of the synthetic jet flow to primary jet flow. The slope angle of the actuator exit has additional functions of regulating the component of the synthetic jet momentum. Based upon analyzing the physical factors of jet vectoring control with synthetic jets, the source variables of the physical factors were established. A preparatory control model of jet vectoring using synthetic jet actuator was presented, and it has the benefit of explaining the efficiency of jet vectoring using synthetic jet actuator with source variables at different values, and it indicates the optimal actuator is taking full advantage of the regulating function.

  1. Plasma Jet Modeling for PLX

    Science.gov (United States)

    Mason, Caroline F.; Mason, Rodney J.; Faehl, R. J.; Kirkpatrick, R. C.

    2011-10-01

    The implicit simulation code ePLAS has been applied to plasma jets generated with mini-rail guns for plasma production and compression aimed at use with PLX. The rails are typically planar, 2.5 cm apart and arranged to transport an initial 1 cm or wider vertical plasma fill some 10 cm into a void. The driving magnetic field is 3.2 T. The plasma singly ionized argon at 1017 cm-3. We use ePLAS in both its traditional implicit/hybrid form where it is restricted by an electron Courant time step, and in a new super-hybrid form that extracts the main electron moments from the E&B-field solutions. This provides numerical stability at ion Courant limits, for at least a 10 times larger time step, thus probing microsecond jet dynamics with computational economy. We examine possible field penetration at the cathode and anode gun electrodes. Cathode erosion and EMHD B - Field penetration are possible at lower jet densities. We examine jet transport beyond the gun, modeling possible ionization with either analytic or tabular EOSs. We study the merger of jets with ions represented as either fluids or particles. Work supported by the USDOE under SBIR GRANT DE-SC0004207.

  2. Advanced Modified High Performance Synthetic Jet Actuator with Curved Chamber

    Science.gov (United States)

    Xu, Tian-Bing (Inventor); Su, Ji (Inventor); Jiang, Xiaoning (Inventor)

    2014-01-01

    The advanced modified high performance synthetic jet actuator with optimized curvature shape chamber (ASJA-M) is a synthetic jet actuator (SJA) with a lower volume reservoir or chamber. A curved chamber is used, instead of the conventional cylinder chamber, to reduce the dead volume of the jet chamber and increase the efficiency of the synthetic jet actuator. The shape of the curvature corresponds to the maximum displacement (deformation) profile of the electroactive diaphragm. The jet velocity and mass flow rate for the ASJA-M will be several times higher than conventional piezoelectric actuators.

  3. EDITORIAL: Plasma jets and plasma bullets Plasma jets and plasma bullets

    Science.gov (United States)

    Kong, M. G.; Ganguly, B. N.; Hicks, R. F.

    2012-06-01

    Plasma plumes, or plasma jets, belong to a large family of gas discharges whereby the discharge plasma is extended beyond the plasma generation region into the surrounding ambience, either by a field (e.g. electromagnetic, convective gas flow, or shock wave) or a gradient of a directionless physical quantity (e.g. particle density, pressure, or temperature). This physical extension of a plasma plume gives rise to a strong interaction with its surrounding environment, and the interaction alters the properties of both the plasma and the environment, often in a nonlinear and dynamic fashion. The plasma is therefore not confined by defined physical walls, thus extending opportunities for material treatment applications as well as bringing in new challenges in science and technology associated with complex open-boundary problems. Some of the most common examples may be found in dense plasmas with very high dissipation of externally supplied energy (e.g. in electrical, optical or thermal forms) and often in or close to thermal equilibrium. For these dense plasmas, their characteristics are determined predominantly by strong physical forces of different fields, such as electrical, magnetic, thermal, shock wave, and their nonlinear interactions [1]. Common to these dense plasma plumes are significant macroscopic plasma movement and considerable decomposition of solid materials (e.g. vaporization). Their applications are numerous and include detection of elemental traces, synthesis of high-temperature materials and welding, laser--plasma interactions, and relativistic jets in particle accelerators and in space [2]-[4]. Scientific challenges in the understanding of plasma jets are exciting and multidisciplinary, involving interweaving transitions of all four states of matter, and their technological applications are wide-ranging and growing rapidly. Using the Web of Science database, a search for journal papers on non-fusion plasma jets reveals that a long initial phase up

  4. Exp erimental study on the characteristics of a two-electro de plasma synthetic jet actuator%两电极等离子体合成射流激励器工作特性研究

    Institute of Scientific and Technical Information of China (English)

    王林; 夏智勋; 罗振兵; 周岩; 张宇

    2014-01-01

    Performance of a two-electrode plasma synthetic jet actuator has been experimentally studied by discharge mea-surements with high-speed shadowgraphy technology. Results show that the breakdown voltage and the peak discharge current of the actuator may be decreased by decreasing the ambient pressure and increasing the discharge frequency. The discharge developed in the actuator cavity is a spark-arc discharge. In the actuator could be created a strong“precursor shock” and a high kinetic energy jet. During the development of the plasma synthetic jet, the speed of the “precursor shock” is invariable and the jet propagates with an approximately local sonic velocity (350 m/s). But with decreasing jet exit diameter and ambient pressure, the increase of the cavity volume and the discharge frequency could lead to decreasing strength of the “precursor shock”. Heating efficiency of the gas in the cavity will decrease with the increase of the cavity volume and discharge frequency, and the jet velocity is decreased as well. The jet exit diameter and the ambient pressure can have their optimal values for affecting the velocity of the jet. Under all the working conditions we have studied, the plasma actuator may create a strong “precursor shock” and a high-speed jet, and also may have the potential to be used in high-speed active flow control.%采用放电测量和高速阴影技术对两电极等离子体合成射流激励器工作特性进行了系统实验研究。实验表明:激励器工作击穿电压和放电峰值电流随激励器所处环境压强的降低和放电频率的增大而减小,激励器腔体内的放电过程为火花电弧放电。典型的等离子体合成射流流场包含有一道前驱激波和一股呈蘑菇状的高速射流。在整个射流发展过程中,前驱激波以当地声速恒速传播,不随激励器条件的改变而变化,波的强度则随着激励器出口直径的减小、腔体体积的增大、环境压

  5. Numerical simulation on micromixer based on synthetic jet

    Institute of Scientific and Technical Information of China (English)

    Minghou Liu; Chen Xie; Xiangfeng Zhang; Yiliang Chen

    2008-01-01

    This paper studied a concept of micromixer with a synthetic jet placed at the bottom of a rectangular channel. Due to periodic ejections from and suctions into the chan-nel, the fluids are mixed effectively. To study the effects of the inlet velocity, the jet intensity and frequency, and the jet location on the mixing efficiency, 3-D numerical simulations of the micromixer have been carried out. It has been found that when the jet intensity and the frequency are fixed, the mixing efficiency increases when Re 50 with the best mixing efficiency achieved at Re = 50. When the ratio of the jet velocity magnitude to the inlet velocity is taken as 10 and the jet frequency is 100 Hz, the mixing index reaches the highest value. It has also been found that to get better mixing efficiency, the orifice of the synthetic jet should be asymmetrically located away from the channel's centerline.

  6. Underwater operation of a DBD plasma jet

    Science.gov (United States)

    Foster, John E.; Weatherford, Brandon; Gillman, Eric; Yee, Benjamin

    2010-04-01

    A plasma jet produced in water using a submerged ac excited electrode in a coaxial dielectric barrier discharge configuration was studied. Plasma jet formation was found to occur only while the source was submerged. Plasma jet operation was characterized with and without gas flow. It was found that over 60% of the discharge power was deposited into the water and did not vary appreciably with excitation frequency. Presumably the remaining power fraction went into excitation, ionization and local electrode heating. Emission spectra of the jet revealed nitrogen, hydrogen, hydroxyl and oxygen emission lines. Operation of the plasma jet in water containing the oxidation-reduction indicator methylene blue dye resulted in a marked clearing of the water as observed visually and with a spectrophotometer, suggesting plasma-induced chemical reactivity.

  7. Atmospheric pressure plasma jet applications

    Energy Technology Data Exchange (ETDEWEB)

    Park, J.; Herrmann, H.W.; Henins, I.; Selwyn, G.S. [Los Alamos National Lab., NM (United States)

    1998-12-31

    The atmospheric pressure plasma jet (APPJ) is a non-thermal, high pressure plasma discharge that produces a high velocity effluent stream of highly reactive chemical species. The discharge operates on a feedstock gas (e.g., He/O2/H2O) which flows between two concentric cylindrical electrodes: an outer grounded electrode and an inner electrode powered at 13.56 MHz RF. While passing through the plasma, the feedgas becomes excited, ionized or dissociated by electron impact. The fast-flowing effluent consists of ions and electrons, which are rapidly lost by recombination, highly reactive radicals (e.g., O, OH), and metastable species (e.g., O2). The metastable O2, which is reactive to hydrocarbon and other organic species, has been observed through optical emission spectroscopy to decrease by a factor of 2 from the APPJ nozzle exit to a distance of 10 cm. Unreacted metastable O2, and that which does not impinge on a surface, will then decay back to ordinary ground state O2, resulting in a completely dry, environmentally-benign form of surface cleaning. Applications such as removal of photoresist, oxide films and organic residues from wafers for the electronics industry, decontamination of civilian and military areas and personnel exposed to chemical or biological warfare agents, and paint (e.g., graffiti) removal are being considered.

  8. Experimental investigation into flow in an ejector with four synthetic jets

    Directory of Open Access Journals (Sweden)

    Dančová Petra

    2012-04-01

    Full Text Available The article deals with experimental investigation into flow in an ejector with four synthetic jets. The aim of the synthetic jets is to excite the mixing layer in the ejector and intensify the mixing process. The cavities of the synthetic jet actuators are hidden in the mixing chamber wall and the synthetic jets are perpendicular to the ejector axis. CTA and pneumatic measuring method were used to investigate the influences of synthetic jets on flow inside the ejector.

  9. Computational Study on Effect of Synthetic Jet Design Parameters

    Directory of Open Access Journals (Sweden)

    Koichi Okada

    2010-01-01

    Full Text Available Effects of amplitude and frequency of synthetic jet on the characteristics of induced jet are investigated. To estimate effects of the parameters, flow inside the synthetic jet cavity and orifice and the outer flow is simultaneously simulated using large-eddy simulation (LES. Comparison of the present LES result with the experimental data shows that three-dimensional LES of the flow inside the cavity is essential for accurate estimation of the velocity and velocity fluctuation of the synthetic jet. Comparison of the present results under various flow conditions shows that amplitude and frequency can control profiles of time-averaged vertical velocity and fluctuation of the vertical velocity as well as damping rate of the induced velocity and fluctuation.

  10. Jet flow and premixed jet flame control by plasma swirler

    Science.gov (United States)

    Li, Gang; Jiang, Xi; Zhao, Yujun; Liu, Cunxi; Chen, Qi; Xu, Gang; Liu, Fuqiang

    2017-04-01

    A swirler based on dielectric barrier discharge plasma actuators is designed and its effectiveness in both jet flow and premixed jet flame control is demonstrated. In contrast to traditional spanwise-oriented actuators, plasma actuators are placed along the axial direction of the injector to induce a circumferential velocity to the main flow and create a swirl flow without any insertion or moving part. In the DBD plasma swirl injector, the discharge does not ignite the mixture nor does it induce flashback. Flame visualization is obtained by cameras while velocity profiles are obtained by Laser Doppler Anemometry measurements. The results obtained indicate the effectiveness of the new design.

  11. Mechanisms of Plasma Acceleration in Coronal Jets

    Science.gov (United States)

    Soto, N.; Reeves, K.; Savcheva, A. S.

    2016-12-01

    Jets are small explosions that occur frequently in the Sun possibly driven by the local reconfiguration of the magnetic field, or reconnection. There are two types of coronal jets: standard jets and blowout jets. The purpose of this project is to determine which mechanisms accelerate plasma in two different jets, one that occurred in January 17, 2015 at the disk of the sun and another in October 24, 2015 at the limb. Two possible acceleration mechanisms are chromospheric evaporation and magnetic acceleration. Using SDO/AIA, Hinode/XRT and IRIS data, we create height-time plots, and calculate the velocities of each wavelength for both jets. We calculate the potential magnetic field of the jet and the general region around it to gain a more detailed understanding of its structure, and determine if the jet is likely to be either a standard or blowout jet. Finally, we calculate the magnetic field strength for different heights along the jet spire, and use differential emission measures to calculate the plasma density. Once we have these two values, we calculate the Alfven speed. When analyzing our results we are looking for certain patterns in our velocities. If the plasma in a jet is accelerated by chromospheric evaporation, we expect the velocities to increase as function of temperature, which is what we observed in the October 24th jet. The magnetic models for this jet also show the Eiffel Tower shaped structure characteristic of standard jets, which tend to have plasma accelerated by this mechanism. On the other hand, if the acceleration mechanism were magnetic acceleration, we would expect the velocities to be similar regardless of temperature. For the January 17th jet, we saw that along the spire, the velocities where approximately 200 km/s in all wavelengths, but the velocities of hot plasma detected at the base were closer to the Alfven speed, which was estimated to be about 2,000 km/s. These observations suggest that the plasma in the January 17th jet is

  12. Formation Mechanism of Atmospheric Pressure Plasma Jet

    CERN Document Server

    Jiang, Nan; Cao, Zexian

    2008-01-01

    Atmospheric pressure plasma jet can protrude some 5.0 cm into air. It holds promise for multivarious innovative applications, but its formation mechanism remains unsettled. We show that the plasma jet is essentially a streamer corona totally independent of, but obscured by, dielectric barrier discharge. Consequently, the jets can be equally successfully generated even with one single bare metal electrode attached to the tube orifice, both downstream and upstream simultaneously, and at a significantly reduced voltage. These results will help understand the underlying physics and facilitate a safer and more flexible implementation of this marvelous plasma source.

  13. Modelling the Plasma Jet in Multi-Arc Plasma Spraying

    Science.gov (United States)

    Bobzin, K.; Öte, M.; Schein, J.; Zimmermann, S.; Möhwald, K.; Lummer, C.

    2016-08-01

    Particle in-flight characteristics in atmospheric plasma spraying process are determined by impulse and heat energy transferred between the plasma jet and injected powder particles. One of the important factors for the quality of the plasma-sprayed coatings is thus the distribution of plasma gas temperatures and velocities in plasma jet. Plasma jets generated by conventional single-arc plasma spraying systems and their interaction with powder particles were subject matter of intensive research. However, this does not apply to plasma jets generated by means of multi-arc plasma spraying systems yet. In this study, a numerical model has been developed which is designated to dealing with the flow characteristics of the plasma jet generated by means of a three-cathode spraying system. The upstream flow conditions, which were calculated using a priori conducted plasma generator simulations, have been coupled to the plasma jet simulations. The significances of the relevant numerical assumptions and aspects of the models are analyzed. The focus is placed on to the turbulence and diffusion/demixing modelling. A critical evaluation of the prediction power of the models is conducted by comparing the numerical results to the experimental results determined by means of emission spectroscopic computed tomography. It is evident that the numerical models exhibit a good accuracy for their intended use.

  14. More Insight of Piezoelectric-based Synthetic Jet Actuators

    Science.gov (United States)

    Housley, Kevin; Amitay, Michael

    2016-11-01

    Increased understanding of the internal flow of piezoelectric-based synthetic jet actuators is needed for the development of specialized actuator cavity geometries to increase jet momentum coefficients and tailor acoustic resonant frequencies. Synthetic jet actuators can benefit from tuning of the structural resonant frequency of the piezoelectric diaphragm(s) and the acoustic resonant frequency of the actuator cavity such that they experience constructive coupling. The resulting coupled behavior produces increased jet velocities. The ability to design synthetic jet actuators to operate with this behavior at select driving frequencies allows for them to be better used in flow control applications, which sometimes require specific jet frequencies in order to utilize the natural instabilities of a given flow field. A parametric study of varying actuator diameters was conducted to this end. Phase-locked data were collected on the jet velocity, the cavity pressure at various locations, and the three-dimensional deformation of the surface of the diaphragm. These results were compared to previous analytical work on the interaction between the structural resonance of the diaphragm and the acoustic resonance of the cavity. Funded by the Boeing Company.

  15. Coronal Jet Plasma Properties and Acceleration Mechanisms

    Science.gov (United States)

    Farid, Samaiyah; Reeves, Kathy; Savcheva, Antonia; Soto, Natalia

    2017-08-01

    Coronal jets are transient eruptions of plasma typically characterized by aprominent long spire and a bright base, and sometimes accompanied by a small filament. Jets are thought to be produced by magnetic reconnection when small-scale bipolar magnetic fields emerge into an overlying coronal field or move into a locally unipolar region. Coronal jets are commonly divided into two categories: standard jets and blowout jets, and are found in both quiet and active regions. The plasma properties of jets vary across type and location, therefore understanding the underlying acceleration mechanisms are difficult to pin down. In this work, we examine both blow-out and standard jets using high resolution multi-wavelength data. Although reconnection is commonly accepted as the primary acceleration mechanism, we also consider the contribution chromospheric evaporation to jet formation. We use seven coronal channels from SDO/AIA , Hinode/XRT Be-thin and IRIS slit-jaw data. In addition, we separate the Fe-XVIII line from the SDO/94Å channel. We calculate plasma properties including velocity, Alfven speed, and density as a function of wavelength and Differential Emission Measure (DEM). Finally, we explore the magnetic topology of the jets using Coronal Modeling System (CMS) to construct potential and non-linear force free models based on the flux rope insertion method.

  16. Mixing in plasma and low density jets

    Science.gov (United States)

    Russ, S.; Strykowski, P. J.; Pfender, E.

    1994-04-01

    This study was undertaken to examine the mechanisms which produce the large entrainment measured near the exit of thermal plasma torches. A research facility was constructed to examine low density jet behavior under similar dimensionless conditions as those produced by thermal plasma spray torches; the Reynolds number based on jet diameter and average properties was 1000, and the ratio of jet to ambient density was 0.07. This very low density jet produced organized vortex structures which were partially responsible for the rapid entrainment of external air. The formation of these organized structures could be disrupted by introducing turbulence, but the rapid entrainment process was not significantly affected. The structure of the jet produced by a commercial plasma torch was examined and compared to the low density research jet. At low gas flow rates the plasma jet also displayed the formation of coherent vortex structures, the passage frequency of which compared favorably with that measured in the low density research jet. At higher gas flow rates the shear layer of the plasma jet rapidly broke down producing relatively small scale turbulence. Visualizations of the hot plasma core were compared against measurements of the torch voltage fluctuations caused by arc instabilities. At low flow rates the arc voltage fluctuations were quite low and the plume was very steady. At higher flow rates the arc voltage fluctuations increased and produced “surging” and “whipping” in the hot potential core. It is believed that this low frequency unsteadiness is partially responsible for the rapid entrainment measured in plasma torches.

  17. Modal Decomposition of Synthetic Jet Flow Based on CFD Computation

    Directory of Open Access Journals (Sweden)

    Hyhlík Tomáš

    2015-01-01

    Full Text Available The article analyzes results of numerical simulation of synthetic jet flow using modal decomposition. The analyzes are based on the numerical simulation of axisymmetric unsteady laminar flow obtained using ANSYS Fluent CFD code. Three typical laminar regimes are compared from the point of view of modal decomposition. The first regime is without synthetic jet creation with Reynolds number Re = 76 and Stokes number S = 19.7. The second studied regime is defined by Re = 145 and S = 19.7. The third regime of synthetic jet work is regime with Re = 329 and S = 19.7. Modal decomposition of obtained flow fields is done using proper orthogonal decomposition (POD where energetically most important modes are identified. The structure of POD modes is discussed together with classical approach based on phase averaged velocities.

  18. Merging of high speed argon plasma jets

    Energy Technology Data Exchange (ETDEWEB)

    Case, A.; Messer, S.; Brockington, S.; Wu, L.; Witherspoon, F. D. [HyperV Technologies Corp., Chantilly, Virginia 22180 (United States); Elton, R. [University of Maryland, College Park, Maryland 20742 (United States)

    2013-01-15

    Formation of an imploding plasma liner for the plasma liner experiment (PLX) requires individual plasma jets to merge into a quasi-spherical shell of plasma converging on the origin. Understanding dynamics of the merging process requires knowledge of the plasma phenomena involved. We present results from the study of the merging of three plasma jets in three dimensional geometry. The experiments were performed using HyperV Technologies Corp. 1 cm Minirailguns with a preionized argon plasma armature. The vacuum chamber partially reproduces the port geometry of the PLX chamber. Diagnostics include fast imaging, spectroscopy, interferometry, fast pressure probes, B-dot probes, and high speed spatially resolved photodiodes, permitting measurements of plasma density, temperature, velocity, stagnation pressure, magnetic field, and density gradients. These experimental results are compared with simulation results from the LSP 3D hybrid PIC code.

  19. Synthetic diagnostics platform for fusion plasmas (invited)

    Energy Technology Data Exchange (ETDEWEB)

    Shi, L., E-mail: lshi@pppl.gov; Valeo, E. J.; Tobias, B. J.; Kramer, G. J.; Hausammann, L.; Tang, W. M. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08540 (United States); Chen, M. [Department of Mechanical and Aerospace Engineering, University of California, Davis, California 95616 (United States)

    2016-11-15

    A Synthetic Diagnostics Platform (SDP) for fusion plasmas has been developed which provides state of the art synthetic reflectometry, beam emission spectroscopy, and Electron Cyclotron Emission (ECE) diagnostics. Interfaces to the plasma simulation codes GTC, XGC-1, GTS, and M3D-C{sup 1} are provided, enabling detailed validation of these codes. In this paper, we give an overview of SDP’s capabilities, and introduce the synthetic diagnostic modules. A recently developed synthetic ECE Imaging module which self-consistently includes refraction, diffraction, emission, and absorption effects is discussed in detail. Its capabilities are demonstrated on two model plasmas. The importance of synthetic diagnostics in validation is shown by applying the SDP to M3D-C{sup 1} output and comparing it with measurements from an edge harmonic oscillation mode on DIII-D.

  20. Using Synthetic Kerosene in Civil Jet Aircraft

    NARCIS (Netherlands)

    Snijders, T.A.; Melkert, J.A.

    2008-01-01

    TU Delft in the Netherlands is performing research into the effects of the use of synthetic kerosene in aircraft. The research program consists of both desk research and tests. In the desk research gas turbine simulations will be combined with payload range performance calculations to show engine ef

  1. Using Synthetic Kerosene in Civil Jet Aircraft

    NARCIS (Netherlands)

    Snijders, T.A.; Melkert, J.A.

    2008-01-01

    TU Delft in the Netherlands is performing research into the effects of the use of synthetic kerosene in aircraft. The research program consists of both desk research and tests. In the desk research gas turbine simulations will be combined with payload range performance calculations to show engine

  2. Transrelativistic pair plasmas in AGN jets

    DEFF Research Database (Denmark)

    Bottcher, M.; Pohl, M.; Schlickeiser, R.

    1999-01-01

    Models of relativistic jets filled with ultrarelativistic pair plasma are very successful in explaining the broadband radiation of gamma-ray blazars. Assuming that the initial injection and cooling of ultrarelativistic pair plasma in an AGN jet has occurred, producing the observed high-energy gamma......-ray radiation, we investigate the further evolution of the pair plasma as it continues to move out from the central engine. The effects of thermalization and reacceleration, the emission of pair bremsstrahlung and annihilation radiation and the bulk Compton process, and the possible application to MeV blazars...

  3. Laboratory plasma physics experiments using merging supersonic plasma jets

    OpenAIRE

    Hsu, S C; Moser, A. L.; Merritt, E. C.; Adams, C. S.; Dunn, J. P.; Brockington, S.; Case, A; Gilmore, M.; Lynn, A. G.; Messer, S. J.; Witherspoon, F. D.

    2014-01-01

    We describe a laboratory plasma physics experiment at Los Alamos National Laboratory that uses two merging supersonic plasma jets formed and launched by pulsed-power-driven rail guns. The jets can be formed using any atomic species or mixture available in a compressed-gas bottle and have the following nominal initial parameters at the railgun nozzle exit: $n_e\\approx n_i \\sim 10^{16}$ cm$^{-3}$, $T_e \\approx T_i \\approx 1.4$ eV, $V_{\\rm jet}\\approx 30$-100 km/s, mean charge $\\bar{Z}\\approx 1$...

  4. Inductive Measurement of Plasma Jet Electrical Conductivity

    Science.gov (United States)

    Turner, Matthew W.; Hawk, Clark W.; Litchford, Ron J.

    2005-01-01

    An inductive probing scheme, originally developed for shock tube studies, has been adapted to measure explosive plasma jet conductivities. In this method, the perturbation of an applied magnetic field by a plasma jet induces a voltage in a search coil, which, in turn, can be used to infer electrical conductivity through the inversion of a Fredholm integral equation of the first kind. A 1-inch diameter probe was designed and constructed, and calibration was accomplished by firing an aluminum slug through the probe using a light-gas gun. Exploratory laboratory experiments were carried out using plasma jets expelled from 15-gram high explosive shaped charges. Measured conductivities were in the range of 3 kS/m for unseeded octol charges and 20 kS/m for seeded octol charges containing 2% potassium carbonate by mass.

  5. Visualization of synthetic jets at higher Stokes numbers

    Directory of Open Access Journals (Sweden)

    Trávníček Zdeněk

    2012-04-01

    Full Text Available Visualization of synthetic jets at higher Stokes numbers (S = 90 and 127 by the phase-locked smoke-wire technique is presented and discussed. The working fluid is air. The Reynolds numbers are quantified using hot-wire anemometry. Although our method of visualization essentially provides only qualitative results, the present study also demonstrates some quantitative results, namely the behavior of the zero-net-mass-flux jet near its critical stage. Visualization of the sub-critical stage is also shown.

  6. Detached divertor plasmas in JET

    Energy Technology Data Exchange (ETDEWEB)

    Horton, L.D.; Borrass, K.; Corrigan, G.; Gottardi, N.; Lingertat, J.; Loarte, A.; Simonini, R.; Stamp, M.F.; Taroni, A. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Stangeby, P.C. [Toronto Univ., ON (Canada). Inst. for Aerospace Studies

    1994-07-01

    In simulations with high radiated power fractions, it is possible to produce the drop in ion current to the divertor targets typical of detached plasmas. Despite the fact that these experiments are performed on beryllium target tiles, radiation from deuterium and beryllium cannot account for the measured power losses. The neutral deuterium levels in the SOL in these plasmas are higher than the model predicts. This may be due to leakage from the divertor or to additional wall sources related to the non-steady nature of these plasmas. In contrast, a surprisingly high level of carbon is present in these discharges; higher even than would be predicted are the divertor target tiles pure carbon. This level may well be large enough to produce the measured radiation. (authors). 6 refs., 2 figs., 1 tab.

  7. Experimental study on flow and heat transfer characteristics of synthetic jet driven by piezoelectric actuator

    Institute of Scientific and Technical Information of China (English)

    ZHANG JingZhou; TAN XiaoMing

    2007-01-01

    To investigate the flow and heat transfer characteristics of a synthetic jet driven by piezoelectric actuator, experimental investigation utilizing particle image velocimetry, hot-wire anemometer and infrared camera was carried out. The results show that: (1) At the jet orifice exit, pairs of vortexes are generated, broken down and merged together periodically, forming a steady jet within a several slot width from distance near the orifice exit. And during the development, the synthetic jet spreads rapidly along the minor axis direction of the orifice. While along the major axis direction, the synthetic jet contracts firstly and then spreads slowly. (2) Excitation frequency forced on the actuator has a great effect on the synthetic jet flow field. There are two resonance frequencies at which the mean velocity and vorticity of the synthetic jet are maximized, especially at the higher resonance frequency.The resonance frequency values obtained by the experiment are lower than the theoretical values. (3) Similarly to the common jet impingement, the convective heat transfer coefficients at the target surface impinged by the synthetic jet also take on up-down tendency varying with the jet-to-surface spacing increment. But the jet-to-surface spacing ratio for optimum cooling achievement is greater and the cooling action region is wider than the former, indicating that the synthetic jet introduces a stronger entrainment and more vigorous penetration in the surrounding fluid.

  8. Experimental study on flow and heat transfer characteristics of synthetic jet driven by piezoelectric actuator

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    To investigate the flow and heat transfer characteristics of a synthetic jet driven by piezoelectric actuator, experimental investigation utilizing particle image veloci- metry, hot-wire anemometer and infrared camera was carried out. The results show that: (1) At the jet orifice exit, pairs of vortexes are generated, broken down and merged together periodically, forming a steady jet within a several slot width from distance near the orifice exit. And during the development, the synthetic jet spreads rapidly along the minor axis direction of the orifice. While along the major axis direction, the synthetic jet contracts firstly and then spreads slowly. (2) Exci- tation frequency forced on the actuator has a great effect on the synthetic jet flow field. There are two resonance frequencies at which the mean velocity and vorticity of the synthetic jet are maximized, especially at the higher resonance frequency. The resonance frequency values obtained by the experiment are lower than the theoretical values. (3) Similarly to the common jet impingement, the convective heat transfer coefficients at the target surface impinged by the synthetic jet also take on up-down tendency varying with the jet-to-surface spacing increment. But the jet-to-surface spacing ratio for optimum cooling achievement is greater and the cooling action region is wider than the former, indicating that the synthetic jet in- troduces a stronger entrainment and more vigorous penetration in the surrounding fluid.

  9. Magnetized plasma jets in experiment and simulation

    Science.gov (United States)

    Schrafel, Peter; Greenly, John; Gourdain, Pierre; Seyler, Charles; Blesener, Kate; Kusse, Bruce

    2013-10-01

    This research focuses on the initial ablation phase of a thing (20 micron) Al foil driven on the 1 MA-in-100 ns COBRA through a 5 mm diameter cathode in a radial configuration. In these experiments, ablated surface plasma (ASP) on the top of the foil and a strongly collimated axial plasma jet can be observed developing midway through current-rise. Our goal is to establish the relationship between the ASP and the jet. These jets are of interest for their potential relevance to astrophysical phenomena. An independently pulsed 200 μF capacitor bank with a Helmholtz coil pair allows for the imposition of a slow (150 μs) and strong (~1 T) axial magnetic field on the experiment. Application of this field eliminates significant azimuthal asymmetry in extreme ultraviolet emission of the ASP. This asymmetry is likely a current filamentation instability. Laser-backlit shadowgraphy and interferometry confirm that the jet-hollowing is correlated with the application of the axial magnetic field. Visible spectroscopic measurements show a doppler shift consistent with an azimuthal velocity in the ASP caused by the applied B-field. Computational simulations with the XMHD code PERSEUS qualitatively agree with the experimental results.

  10. Commercial Approval Plan for Synthetic Jet Fuel from Hydrotreated Fats and Oils

    Science.gov (United States)

    2009-02-18

    qualification plan entitled "Commercial Approval Plan for Synthetic Jet Fuel from Hydrotreated Fats and Oils," produced by the subcontractor, Southwest...102 Enclosure 1 February 12, 2009 Fuel Qualification Plan; 3/27/07–4/24/09 Commercial Approval Plan for Synthetic Jet Fuel from Hydrotreated Fats and...Institute, Grand Forks, ND Southwest Research Institute, San Antonio, TX CLIN 0008 10 COMMERCIAL APPROVAL PLAN FOR SYNTHETIC JET FUEL FROM HYDROTREATED FATS

  11. Properties of velocity field in the vicinity of synthetic jet generator

    Science.gov (United States)

    Strzelczyk, P.; Gil, P.

    2016-10-01

    The paper presents the results of experimental investigation of velocity field in the vicinity of synthetic jet actuator as a function of Stokes number and for constant Reynolds number. A constant temperature hot-wire anemometer with tungsten-platinum coated single wire probe used for the velocity measurements. Synthetic jet flow visualization was presented, especially process of vortex ring development. Synthetic jet velocity profiles were compared with a solution to fully-developed pipe flow with an oscillating pressure gradient.

  12. Experimental research of the synthetic jet generator designs based on actuation of diaphragm with piezoelectric actuator

    Science.gov (United States)

    Rimasauskiene, R.; Matejka, M.; Ostachowicz, W.; Kurowski, M.; Malinowski, P.; Wandowski, T.; Rimasauskas, M.

    2015-01-01

    Experimental analyses of four own developed synthetic jet generator designs were presented in this paper. The main task of this work was to find the most appropriate design of the synthetic jet generator. Dynamic characteristics of the synthetic jet generator's diaphragm with piezoelectric material were measured using non-contact measuring equipment laser vibrometer Polytec®PSV 400. Temperatures of the piezoelectric diaphragms working in resonance frequency were measured with Fiber Bragg Grating (FBG) sensor. Experimental analysis of the synthetic jet generator amplitude-frequency characteristics were performed using CTA (hot wire anemometer) measuring techniques. Piezoelectric diaphragm in diameter of 27 mm was excited by sinusoidal voltage signal and it was fixed tightly inside the chamber of the synthetic jet generator. The number of the synthetic jet generator orifices (1 or 3) and volume of cavity (height of cavity vary from 0.5 mm to 1.5 mm) were changed. The highest value of the synthetic jet velocity 25 m/s was obtained with synthetic jet generator which has cavity 0.5 mm and 1 orifice (resonance frequency of the piezoelectric diaphragm 2.8 kHz). It can be concluded that this type of the design is preferred in order to get the peak velocity of the synthetic jet.

  13. Magnetized laboratory plasma jets: Experiment and simulation

    Science.gov (United States)

    Schrafel, Peter; Bell, Kate; Greenly, John; Seyler, Charles; Kusse, Bruce

    2015-01-01

    Experiments involving radial foils on a 1 M A , 100 n s current driver can be used to study the ablation of thin foils and liners, produce extreme conditions relevant to laboratory astrophysics, and aid in computational code validation. This research focuses on the initial ablation phase of a 20 μ m Al foil (8111 alloy), in a radial configuration, driven by Cornell University's COBRA pulsed power generator. In these experiments ablated surface plasma (ASP) on the top side of the foil and a strongly collimated axial plasma jet are observed developing midway through the current rise. With experimental and computational results this work gives a detailed description of the role of the ASP in the formation of the plasma jet with and without an applied axial magnetic field. This ˜1 T field is applied by a Helmholtz-coil pair driven by a slow, 150 μ s current pulse and penetrates the load hardware before arrival of the COBRA pulse. Several effects of the applied magnetic field are observed: (1) without the field extreme-ultraviolet emission from the ASP shows considerable azimuthal asymmetry while with the field the ASP develops azimuthal motion that reduces this asymmetry, (2) this azimuthal motion slows the development of the jet when the field is applied, and (3) with the magnetic field the jet becomes less collimated and has a density minimum (hollowing) on the axis. PERSEUS, an XMHD code, has qualitatively and quantitatively reproduced all these experimental observations. The differences between this XMHD and an MHD code without a Hall current and inertial effects are discussed. In addition the PERSEUS results describe effects we were not able to resolve experimentally and suggest a line of future experiments with better diagnostics.

  14. Spray Characterization of Gas-to-Liquid Synthetic Jet Fuels

    Science.gov (United States)

    Kannaiyan, Kumaran; Sadr, Reza; GTL jet fuel Consortium Team

    2012-11-01

    Gas-to-Liquid (GTL) Synthetic Paraffinic Kerosene (SPK) fuel obtained from Fischer-Tropsch synthesis has grabbed the global attention due to its cleaner combustion characteristics. GTL fuels are expected to meet the vital qualities such as atomization, combustion and emission characteristics of conventional jet fuels. It is imperative to understand fuel atomization in order to gain insights on the combustion and emission aspects of an alternative fuel. In this work spray characteristics of GTL-SPK, which could be used as a drop-in fuel in aircraft gas turbine engines, is studied. This work outlines the spray experimental facility, the methodology used and the results obtained using two SPK's with different chemical compositions. The spray characteristics, such as droplet size and distribution, are presented at three differential pressures across a simplex nozzle and compared with that of the conventional Jet A-1 fuel. Experimental results clearly show that although the chemical composition is significantly different between SPK's, the spray characteristics are not very different. This could be attributed to the minimal difference in fluid properties between the SPK's. Also, the spray characteristics of SPK's show close resemblance to the spray characteristics of Jet A-1 fuel.

  15. Plasma current asymmetries during disruptions in JET

    Science.gov (United States)

    Gerasimov, S. N.; Hender, T. C.; Morris, J.; Riccardo, V.; Zakharov, L. E.; EFDA Contributors, JET

    2014-07-01

    A key feature of disruptions during vertical displacement events, discovered in JET in 1996, is the toroidal variation in the measured plasma current Ip, i.e. the plasma current asymmetries, lasting for almost the entire current quench. The unique magnetic diagnostics at JET (full set of poloidal coils and saddle loops recorded either from two toroidally opposite or from four toroidally orthogonal locations) allow for a comprehensive analysis of asymmetrical disruptions with a large scale database. This paper presents an analysis of 4854 disruptions over an 18 year period that includes both the JET carbon (C) wall and the ITER-like (IL) wall (a mixed beryllium/tungsten first wall). In spite of the Ip quench time significantly increasing for the IL-wall compared to C-wall disruptions, the observed toroidal asymmetry time integral (˜ sideways force impulse), did not increase for IL-wall disruptions. The Ip asymmetry has a dominantly n = 1 structure. Its motion in the toroidal direction has a sporadic behaviour, in general. The distributions of the number of rotation periods are found to be very similar for both C- and IL-wall disruptions, and multi-turn rotation was sometimes observed. The Ip asymmetry amplitude has no degradation with rotation frequency for either the C- or IL-wall disruption. Therefore dynamic amplification remains a potentially serious issue for ITER due to possible mechanical resonance of the machine components with the rotating asymmetry.

  16. Plasma Waves and Jets from Moving Conductors

    CERN Document Server

    Gralla, Samuel E

    2016-01-01

    We consider force-free plasma waves launched by the motion of conducting material through a magnetic field. We develop a spacetime-covariant formalism for perturbations of a uniform magnetic field and show how the transverse motion of a conducting fluid acts as a source. We show that fast-mode waves are sourced by the compressibility of the fluid, with incompressible fluids launching a pure-Alfven outflow. Remarkably, this outflow can be written down in closed form, at the nonlinear level, for an arbitrary incompressible flow. The instantaneous flow velocity is imprinted on the magnetic field and transmitted away at the speed of light, carrying detailed information about the conducting source at the time of emission. These results can be applied to transients in pulsar outflows and to jets from neutron stars orbiting in the magnetosphere of another compact object. We discuss jets from moving conductors in some detail.

  17. Electron dynamics and plasma jet formation in a helium atmospheric pressure dielectric barrier discharge jet

    Energy Technology Data Exchange (ETDEWEB)

    Algwari, Q. Th. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); Electronic Department, College of Electronics Engineering, Mosul University, Mosul 41002 (Iraq); O' Connell, D. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); York Plasma Institute, Department of Physics, University of York, York YO10 5DD (United Kingdom)

    2011-09-19

    The excitation dynamics within the main plasma production region and the plasma jets of a kHz atmospheric pressure dielectric barrier discharge (DBD) jet operated in helium was investigated. Within the dielectric tube, the plasma ignites as a streamer-type discharge. Plasma jets are emitted from both the powered and grounded electrode end; their dynamics are compared and contrasted. Ignition of these jets are quite different; the jet emitted from the powered electrode is ignited with a slight time delay to plasma ignition inside the dielectric tube, while breakdown of the jet at the grounded electrode end is from charging of the dielectric and is therefore dependent on plasma production and transport within the dielectric tube. Present streamer theories can explain these dynamics.

  18. Magnetized and collimated millimeter scale plasma jets with astrophysical relevance

    Energy Technology Data Exchange (ETDEWEB)

    Brady, Parrish C.; Quevedo, Hernan J. [Texas Center for High Intensity Laser Science, University of Texas at Austin, Austin, Texas 78712 (United States); Valanju, Prashant M. [Institute for Fusion Studies, University of Texas at Austin, Austin, Texas 78712-1060 (United States); Bengtson, Roger D.; Ditmire, Todd [Department of Physics, University of Texas at Austin, Austin, Texas 78712 (United States)

    2012-01-15

    Magnetized collimated plasma jets are created in the laboratory to extend our understanding of plasma jet acceleration and collimation mechanisms with particular connection to astrophysical jets. In this study, plasma collimated jets are formed from supersonic unmagnetized flows, mimicking a stellar wind, subject to currents and magnetohydrodynamic forces. It is found that an external poloidal magnetic field, like the ones found anchored to accretion disks, is essential to stabilize the jets against current-driven instabilities. The maximum jet length before instabilities develop is proportional to the field strength and the length threshold agrees well with Kruskal-Shafranov theory. The plasma evolution is modeled qualitatively using MHD theory of current-carrying flux tubes showing that jet acceleration and collimation arise as a result of electromagnetic forces.

  19. Comparison of Vibrations and Emissions of Conventional Jet Fuel with Stressed 100% SPK and Fully Formulated Synthetic Jet Fuel

    Directory of Open Access Journals (Sweden)

    Bhupendra Khandelwal

    2014-08-01

    Full Text Available The rapid growth of the aviation sector around the globe has witnessed an overwhelming impact on fossil fuel resources. With the implementation of stricter environmental laws over emissions by conventional jet fuels, growing demand for research on alternative fuels has become imperative. One-hundred percent Synthetic Paraffinic Kerosene (SPK and Fully Formulated Synthetic Jet Fuel have surfaced as viable alternatives for gas turbine engines due to their similar properties as that of Jet Fuel. This paper presents results from an experimental study performed on a small gas turbine engine, comparing emissions performance and vibrations for conventional Jet A-1 Fuel, thermally stressed 100% SPK and Fully Formulated Synthetic Jet Fuel. Different vibration frequencies, power spectra were observed for different fuels. Gaseous emissions observed were nearly the same, whereas, significant changes in particulates emissions were observed.

  20. Airfoil drag elimination and stall suppression via piezoelectric dynamic tangential synthetic jet actuators

    NARCIS (Netherlands)

    Barrett, R.; Corpening, J.; Reasonover, C.

    2005-01-01

    This paper describes a new method for drag elimination and stall suppression via tangential synthetic jet actuators. This boundary layer control (BLC) method is shown to perform as well as continuous and normal synthetic jet BLC methods but without fouling difficulties, system-level complexity or ex

  1. The density limit in JET diverted plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, D.J.; Clement, S.; Gottardi, N.; Gowers, C.; Harbour, P.; Loarte, A.; Horton, L.; Lingertat, J.; Lowry, C.G.; Saibene, G.; Stamp, M.; Stork, D. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Monk, R. [Royal Holloway Coll., London (United Kingdom). Dept. of Physics

    1994-07-01

    In JET limiter plasmas the density limit is associated with radiated power fractions of 100% and, in plasmas with carbon limiters, it is invariably disruptive. However, in discharges with solid beryllium limiters the limit is identified with the formation of a MARFE and disruptions are less frequent. In addition, the improved conditioning of the vessel arising from the use of beryllium has significantly improved the density limit scaling, so that the maximum density rises with the square root of the input power. In diverted plasmas several confinement regimes exist, making the characterization of the density limit more complex. While the density limit in L-mode plasmas is generally disruptive, the limit in ELMy and ELM-free H-modes generally prompts a return to the L-mode and a disruption is not inevitable. The density limit does rise with the increasing power, but the L-to-H transition complicates the analysis. Nevertheless, at low plasma currents (<2 MA), densities significantly above the Greenwald limit can be achieved, while at higher currents power handling limitations have constrained the range of density which can be achieved. (authors). 7 refs., 4 figs.

  2. Synthetic Jets for Heat Transfer Augmentation in Microelectronics Systems

    Science.gov (United States)

    Arik, Mehmet; Tamdogan, Enes

    Rapid progress in science and information technology, growing manufacturing activities and increase in globalization have boosted the demand for advanced electronics devices. Moreover, increase in microprocessor power dissipation coupled with the reduction in feature sizes due to manufacturing process improvements have resulted in continuously increasing heat fluxes. Thus, ever increasing heat fluxes have required the development of novel, reliable and affordable thermal management technologies. Although some of those proposed solutions for high flux cooling problems based on liquid cooling methods such as spray and evaporative cooling; air cooling is still commonly preferred due to its availability, reliability, easiness and low cost. Therefore, over the last decade microfluidics devices such as synthetic jets have been investigated as an alternative to conventional air moving devices, and have been shown as highly effective for cooling of electronics in compact thermal real estates...

  3. Interaction of microwave radiation with an erosion plasma jet

    Science.gov (United States)

    Brovkin, V. G.; Pashchina, A. S.; Ryazanskiy, N. M.

    2016-09-01

    The interaction of high-power pulsed microwave radiation with a plasma jet formed by a discharge in an ablative capillary is studied. A significant influence of microwave radiation on the plasma jet flow is found. Depending on the intensity of the initial perturbation of the jet, different scenarios of its evolution downstream are possible: attenuation or amplification accompanied with the development of turbulence up to the disruption of the flow if a certain threshold of the energy action is exceeded. A significant influence of the plasma jet and its state on the spatial position of the microwave energy release zone is found.

  4. The Interactions of Two Cold Atmospheric Plasma Jets

    Institute of Scientific and Technical Information of China (English)

    TANG Daotan; REN Chunsheng; WANG Dezhen; NIE Qiuyue

    2009-01-01

    This paper presents the interactions between two cold atmospheric plasma jets. By changing the experimental conditions including the gas flow rate, the applied voltage, the power supply frequency and the inter-electrode distance d, three different interaction modes, attraction, repulsion and combination, were observed. It is shown that the interaction modes of the two jets are principally affected by the electrodes, the gas flow rate, the plasma jets and the power supply frequency.

  5. Some aspects of flow control over a NACA0015 airfoil using synthetic jets

    Science.gov (United States)

    Parthasarathy, T.; Das, S. P.

    2017-04-01

    Flow control for performance enhancement over airfoils has become an increasingly important topic. This work details the characteristics of flow control using synthetic jets over a NACA0015 airfoil at a Reynolds number of 896,000 based on the chord length and free stream velocity, and at 20° angle of attack wherein the flow is separated. Numerical simulations were performed to help understand the behaviour of the controlled flow for a range of synthetic jet parameters. Analysis of key flow parameters such as phase averaged pressure and streamline profiles indicate that the synthetic jet is efficient in increasing the lift coefficient; more so for larger jet amplitudes and at smaller angles of jet injection. Behaviour of the flow characteristics for controlled cases has been analysed from the flow structures obtained from the same. This work serves as a platform to qualitatively and quantitatively understand the effects of the jet parameters on the separated flow over the airfoil.

  6. Plasma Jet Simulations Using a Generalized Ohm's Law

    Science.gov (United States)

    Ebersohn, Frans; Shebalin, John V.; Girimaji, Sharath S.

    2012-01-01

    Plasma jets are important physical phenomena in astrophysics and plasma propulsion devices. A currently proposed dual jet plasma propulsion device to be used for ISS experiments strongly resembles a coronal loop and further draws a parallel between these physical systems [1]. To study plasma jets we use numerical methods that solve the compressible MHD equations using the generalized Ohm s law [2]. Here, we will discuss the crucial underlying physics of these systems along with the numerical procedures we utilize to study them. Recent results from our numerical experiments will be presented and discussed.

  7. Probing Runaway Electrons with Nanoparticle Plasma Jet

    Science.gov (United States)

    Bogatu, I. N.; Thompson, J. R.; Galkin, S. A.; Kim, J. S.

    2014-10-01

    The injection of C60/C nanoparticle plasma jet (NPPJ) into tokamak plasma during a major disruption has the potential to probe the runaway electrons (REs) during different phases of their dynamics and diagnose them through spectroscopy of C ions visible/UV lines. A C60/C NPPJ of ~75 mg, high-density (>1023 m-3), hyper-velocity (>4 km/s), and uniquely fast response-to-delivery time (~1 ms) has been demonstrated on a test bed. It can rapidly and deeply deliver enough mass to increase electron density to ~2.4 × 1021 m-3, ~60 times larger than typical DIII-D pre-disruption value. We will present the results of our investigations on: 1) C60 fragmentation and gradual release of C atoms along C60 NPPJ penetration path through the RE carrying residual cold plasma, 2) estimation of photon emissivity coefficient for the lines of the C ions, and 3) simulation of C60/C PJ penetration to the RE beam location in equivalent conditions to the characteristic ~1 T B-field of DIII-D. The capabilities of this injection technique provide a unique possibility in understanding and controlling the RE beam, which is a critical problem for ITER. Work supported by US DOE DE-SC0011864 Grant.

  8. Experimental study of cooling performance of pneumatic synthetic jet with singular slot rectangular orifice

    Science.gov (United States)

    Yu, Roger Ho Zhen; Ismail, Mohd Azmi bin; Ramdan, Muhammad Iftishah; Mustaffa, Nur Musfirah binti

    2017-03-01

    Synthetic Jet generates turbulence flow in cooling the microelectronic devices. In this paper, the experiment investigation of the cooling performance of pneumatic synthetic jet with single slot rectangular orifices at low frequency motion is presented. The velocity profile at the end of the orifice was measured and used as characteristic performance of synthetic jet in the present study. Frequencies of synthetic jet and the compressed air pressure supplied to the pneumatic cylinder (1bar to 5bar) were the parameters of the flow measurement. The air velocity of the synthetic jet was measured by using anemometer air flow meter. The maximum air velocity was 0.5 m/s and it occurred at frequency motion of 8 Hz. The optimum compressed air supplied pressure of the synthetic jet study was 4 bar. The cooling performance of synthetic jet at several driven frequencies from 0 Hz to 8 Hz and heat dissipation between 2.5W and 9W were also investigate in the present study. The results showed that the Nusselt number increased and thermal resistance decreased with both frequency and Reynolds number. The lowest thermal resistance was 5.25°C/W and the highest Nusselt number was 13.39 at heat dissipation of 9W and driven frequency of 8Hz.

  9. Experimental studies of collisional plasma shocks and plasma interpenetration via merging supersonic plasma jets

    Science.gov (United States)

    Hsu, S. C.; Moser, A. L.; Merritt, E. C.; Adams, C. S.

    2015-11-01

    Over the past 4 years on the Plasma Liner Experiment (PLX) at LANL, we have studied obliquely and head-on-merging supersonic plasma jets of an argon/impurity or hydrogen/impurity mixture. The jets are formed/launched by pulsed-power-driven railguns. In successive experimental campaigns, we characterized the (a) evolution of plasma parameters of a single plasma jet as it propagated up to ~ 1 m away from the railgun nozzle, (b) density profiles and 2D morphology of the stagnation layer and oblique shocks that formed between obliquely merging jets, and (c) collisionless interpenetration transitioning to collisional stagnation between head-on-merging jets. Key plasma diagnostics included a fast-framing CCD camera, an 8-chord visible interferometer, a survey spectrometer, and a photodiode array. This talk summarizes the primary results mentioned above, and highlights analyses of inferred post-shock temperatures based on observations of density gradients that we attribute to shock-layer thickness. We also briefly describe more recent PLX experiments on Rayleigh-Taylor-instability evolution with magnetic and viscous effects, and potential future collisionless shock experiments enabled by low-impurity, higher-velocity plasma jets formed by contoured-gap coaxial guns. Supported by DOE Fusion Energy Sciences and LANL LDRD.

  10. Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

    Institute of Scientific and Technical Information of China (English)

    Zhao Guoqing; Zhao Qijun

    2014-01-01

    Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier-Stokes equations coupled with akxshear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally, a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturba-tion effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet param-eters (forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies (the best lift-drag ratio at F+=2.0) and jet angles (40? or 75?) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by 26.5%in comparison with the single point control case.

  11. Cellular membrane collapse by atmospheric-pressure plasma jet

    Science.gov (United States)

    Kim, Kangil; Jun Ahn, Hak; Lee, Jae-Hyeok; Kim, Jae-Ho; Sik Yang, Sang; Lee, Jong-Soo

    2014-01-01

    Cellular membrane dysfunction caused by air plasma in cancer cells has been studied to exploit atmospheric-pressure plasma jets for cancer therapy. Here, we report that plasma jet treatment of cervical cancer HeLa cells increased electrical conductivity across the cellular lipid membrane and caused simultaneous lipid oxidation and cellular membrane collapse. We made this finding by employing a self-manufactured microelectrode chip. Furthermore, increased roughness of the cellular lipid membrane and sequential collapse of the membrane were observed by atomic force microscopy following plasma jet treatment. These results suggest that the cellular membrane catastrophe occurs via coincident altered electrical conductivity, lipid oxidation, and membrane roughening caused by an atmospheric-pressure plasma jet, possibly resulting in cellular vulnerability to reactive species generated from the plasma as well as cytotoxicity to cancer cells.

  12. Cellular membrane collapse by atmospheric-pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kangil; Sik Yang, Sang, E-mail: jsjlee@ajou.ac.kr, E-mail: ssyang@ajou.ac.kr [Department of Electrical and Computer Engineering, Ajou University, Suwon 443-749 (Korea, Republic of); Jun Ahn, Hak; Lee, Jong-Soo, E-mail: jsjlee@ajou.ac.kr, E-mail: ssyang@ajou.ac.kr [Department of Biological Sciences, Ajou University, Suwon 443-749 (Korea, Republic of); Lee, Jae-Hyeok; Kim, Jae-Ho [Department of Molecular Science and Technology, Ajou University, Suwon 443-749 (Korea, Republic of)

    2014-01-06

    Cellular membrane dysfunction caused by air plasma in cancer cells has been studied to exploit atmospheric-pressure plasma jets for cancer therapy. Here, we report that plasma jet treatment of cervical cancer HeLa cells increased electrical conductivity across the cellular lipid membrane and caused simultaneous lipid oxidation and cellular membrane collapse. We made this finding by employing a self-manufactured microelectrode chip. Furthermore, increased roughness of the cellular lipid membrane and sequential collapse of the membrane were observed by atomic force microscopy following plasma jet treatment. These results suggest that the cellular membrane catastrophe occurs via coincident altered electrical conductivity, lipid oxidation, and membrane roughening caused by an atmospheric-pressure plasma jet, possibly resulting in cellular vulnerability to reactive species generated from the plasma as well as cytotoxicity to cancer cells.

  13. Far-field momentum flux of high-frequency axisymmetric synthetic jets

    Science.gov (United States)

    Xia, X.; Mohseni, K.

    2015-11-01

    This study focuses on predicting the far-field momentum flux for axisymmetric synthetic jets, which is an important parameter that characterizes the performance of such jets in flow-control applications. Previous researchers have found that a negative pressure gradient near the jet orifice is responsible for the observed decrease in the momentum flux in the streamwise direction. As a result, prediction of the far field momentum flux of synthetic jets has encountered serious challenges. In this paper, the far-field momentum flux is modeled by calculating the hydrodynamic impulse of the vortical structure formed during one actuation cycle, under the assumption that the jet is fully developed and periodic. In this manner, the complex near-field effect of a synthetic jet is explicitly captured by the interactions between the vortices and the actuator. Furthermore, the impulse of these vortical structures is predicted using only the actuation parameters of the synthetic jet, namely, the stroke length, L, the orifice diameter, d, and the actuation frequency, f. For a synthetic jet with a stroke ratio, L/d, larger than the formation number, L∗/d, this model predicts that the normalized far-field momentum flux, K/Ks, decreases when L/d increases. This can be explained by an increasing circulation fraction of the trailing jet, which contains less impulse per unit circulation compared with the leading vortex. This model is validated using hot-wire anemometry measurement of a series of synthetic jets. Moreover, by comparing with experimental data that have large L/d, this model suggests that the contribution of trailing jet to the overall far-field momentum flux is not negligible.

  14. [Spectral diagnosis of plasma jet at atmospheric pressure].

    Science.gov (United States)

    Li, Chi; Tang, Xiao-liang; Qiu, Gao

    2008-12-01

    A new approach to surface modification of materials using dielectric barrier discharge (DBD) plasma jet at atmospheric pressure is presented in the present paper. The emission spectral lines of argon plasma jet at atmospheric pressure were recorded by the grating spectrograph HR2000 and computer software. The argon plasma emission spectra, ranging from 300nm to 1000 nm, were measured at different applied voltage. Compared to air plasma emission spectra under the same circumstance, it is shown that all of the spectral lines are attributed to neutral argon atoms. The spectral lines 763.51 and 772.42 nm were chosen to estimate the electron excitation temperature. The purpose of the study is to research the relationship between the applied voltage and temperature to control the process of materials' surface modification promptly. The results show that electron excitation temperature is in the range of 0.1-0.5 eV and increases with increasing applied voltage. In the process of surface modification under the plasma jet, the infrared radiation thermometer was used to measure the material surface temperature under the plasma jet. The results show that the material surface temperature is in the range of 50-100 degrees C and it also increases with increasing applied voltage. Because the material surface was under the plasma jet and its temperature was decided by the plasma, and the material surface temperature increased with increasing the macro-temperature of plasma jet, the relationship between the surface temperature and applied voltage indicates the relationship between the macro-temperature of the plasma jet and the applied voltage approximately. The experimental results indicate that DBD plasma jet at atmospheric pressure is a new approach to improving the quality of materials' surface modification, and spectral diagnosis has proved to be a kind of workable method by choosing suitable applied voltage.

  15. Electrode Configurations in Atmospheric Pressure Plasma Jets

    Science.gov (United States)

    Lietz, Amanda M.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure plasma jets (APPJs) are being studied for emerging medical applications including cancer treatment and wound healing. APPJs typically consist of a dielectric tube through which a rare gas flows, sometimes with an O2 or H2O impurity. In this paper, we present results from a computational study of APPJs using nonPDPSIM, a 2-D plasma hydrodynamics model, with the goal of providing insights on how the placement of electrodes can influence the production of reactive species. Gas consisting of He/O2 = 99.5/0.5 is flowed through a capillary tube at 2 slpm into humid air, and a pulsed DC voltage is applied. An APPJ with two external ring electrodes will be compared with one having a powered electrode inside and a ground electrode on the outside. The consequences on ionization wave propagation and the production of reactive oxygen and nitrogen species (RONS) will be discussed. Changing the electrode configuration can concentrate the power deposition in volumes having different gas composition, resulting in different RONS production. An internal electrode can result in increased production of NOx and HNOx by increasing propagation of the ionization wave through the He dominated plume to outside of the tube where humid air is diffusing into the plume. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  16. Plasma Jet Interaction with Thomson Scattering Probe Laser

    Science.gov (United States)

    Byvank, Tom; Banasek, Jacob; Potter, William; Kusse, Bruce

    2016-10-01

    Thomson scattering systems can diagnose plasma temperatures and velocities. When probing a plasma jet with the Thomson scattering laser, we observe a laser-plasma interaction that inputs energy into the plasma jet. The absorbed energy causes a bubble of low density ( 5*1017 cm-2) in the jet (unperturbed 1018 cm-2). A pulsed power machine (1 MA peak current, 100 ns rise time) with a radial foil (15 μm thick Al) configuration generates the plasma jet. We compare the effects of using 10 J and 1 J laser energies, for which the 10 J laser is a larger perturbation. We discuss how the interaction affects the Thomson scattering temperature and velocity measurements. Work supported by National Nuclear Security Administration (NNSA) Stewardship Sciences Academic Programs under Department of Energy (DOE) Cooperative Agreement DE-NA0001836 and National Science Foundation (NSF) Grant PHY-1102471.

  17. Numerical Simulation of High-Power Synthetic Jet Actuator Flowfield and its Influence on Mixing Control

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Detailed two-dimensional unsteady numerical simulation is carried out to investigate a high-power synthetic jet actuator flow field and its design characteristic. Simultaneously, mixing control mechanism of coaxial jets with actuators is also studied. Firstly, excitation frequency (rotating speed), piston displacement and its exit slot width have effect on the controlling ability and controlling efficiency of actuator. With the invariable model and concerned parameters, the actuator becomes more desirable as the rotating speed increases. Average velocity and maximal velocity at the actuator exit section increase as the piston displacement enlarges or the exit slot width decreases. But the actuator does not always exhibit good performance with the narrower exit. Secondly, the synthetic jets also have the "push" effect on the coaxial jets, which results in the fluctuation of vorticity and temperature distribution of mixing fiowfield. Finally, the employment of synthetic jet actuator can achieve mixing enhancement significantly.

  18. On Stability of Targets for Plasma Jet Induced Magnetoinertial Fusion

    CERN Document Server

    Samulyak, Roman; Kim, Hyoungekun

    2015-01-01

    The compression and stability of plasma targets for the plasma jet-induced magneto-inertial fusion (PJMIF) have been investigated via large scale simulations using the FronTier code capable of explicit tracking of material interfaces. In the PJMIF concept, a plasma liner, formed by the merger of a large number of radial, highly supersonic plasma jets, implodes on a magnetized plasma target and compresses it to conditions of the fusion ignition. A multi-stage computational approach for simulations of the liner-target interaction and the compression of plasma targets has been developed to minimize computing time. Simulations revealed important features of the target compression process, including instability and disintegration of targets. The non-uniformity of the leading edge of the liner, caused by plasma jets as well as oblique shock waves between them, leads to instabilities during the target compression. By using front tracking, the evolution of targets has been studied in 3-dimensional simulations. Optimi...

  19. Experimental Investigation of a Synthetic Jet Array in a Laminar Channel Flow

    Directory of Open Access Journals (Sweden)

    Trávníček Z.

    2013-04-01

    Full Text Available The paper deals with an impinging synthetic jet, namely on the case of a synthetic jet array interacting with a laminar channel flow. This arrangement can be useful in many micro-scale applications, such as cooling of micro-electronics. The flow regime in micro-scale is usually laminar with very small Reynolds numbers; therefore synthetic jet array can be used for the profile disturbance and heat transfer enhancement. The paper focuses on the low Reynolds number (in order 102. The working fluid is water and a piezoceramic transducer is used as a moving membrane in the synthetic jet actuator. Experiments are performed with four experimental methods (tin ion visualization, hot wire anemometry in constant temperature mode, laser Doppler vibrometry and particle image velocimetry in three laboratories (at the Eindhoven University of Technology, Netherlands, at the Institute of Thermodynamics CAS, v.v.i. and Technical University of Liberec, both Czech Republic.

  20. Lighting system with thermal management system having point contact synthetic jets

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr, Charles Franklin; Sharma, Rajdeep

    2016-08-30

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  1. Lighting system with thermal management system having point contact synthetic jets

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Sharma, Rajdeep

    2016-08-23

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  2. Experimental investigations on separation control and flow structure around a circular cylinder with synthetic jet

    Institute of Scientific and Technical Information of China (English)

    WANG; JinJun; FENG; LiHao; XU; ChaoJun

    2007-01-01

    Circular cylinder separation control and flow structure influenced by the synthetic jet have been experimentally investigated in a water channel. The synthetic jet issues from a slot and ejects toward upstream from the front stagnation point of the cylinder. It has been found that, similar to the traditional synthetic jet which is positioned near the separation point or inside the separation region, the present synthetic jet arrangement constitutes an efficient way to control flow separation of the circular cylinder, but with a different control mechanism. The present synthetic jet leads to an upstream displacement of the front stagnation point and the formation of a vortex pair near both sides of the exit orifice. When ReU based on the synthetic jet average exit orifice velocity is about lower than 43, a closed envelope forms in front of the windward side of the cylinder during the blowing cycle of synthetic jet, which acts as an apparent modification for the cylinder configuration. When ReU is high enough, an open envelope forms upstream of the cylinder, and the flow around the cylinder becomes much energetic. Thus, regardless of ReU, the present synthetic jet can improve separation for flow around a circular cylinder. With regard to the leeward side, as ReU increases, the flow separation region behind the cylinder gradually disappears. The flow over cylinder may be fully attached when the open envelope forms upstream of the cylinder and ReU is greater than 344. Then, the flow past the cylinder will converge near the back stagnation point of the cylinder, where a new vortex pair shedding periodically is generated due to the high shear layer.

  3. Fluctuation Phenomenon Analysis of an Arc Plasma Spraying Jet

    Institute of Scientific and Technical Information of China (English)

    赵文华; 田阔; 刘笛; 张冠忠

    2001-01-01

    The effects of three factors, including the power supply, the arc behaviour in the arc channel and the fluid dynamic process of the jet, on a plasma spraying jet have been experimentally detected by means of spectroscopic diagnostic techniques. The fast Fourier transform method has been applied to the analysis of the arc voltage and spectral line intensity of the jet. The three factors have been studied and distinguished from each other.

  4. MHD simulations of Plasma Jets and Plasma-surface interactions in Coaxial Plasma Accelerators

    Science.gov (United States)

    Subramaniam, Vivek; Raja, Laxminarayan

    2016-10-01

    Coaxial plasma accelerators belong to a class of electromagnetic acceleration devices which utilize a self-induced Lorentz force to accelerate magnetized thermal plasma to large velocities ( 40 Km/s). The plasma jet generated as a result, due to its high energy density, can be used to mimic the plasma-surface interactions at the walls of thermonuclear fusion reactors during an Edge Localized Mode (ELM) disruption event. We present the development of a Magnetohydrodynamics (MHD) simulation tool to describe the plasma acceleration and jet formation processes in coaxial plasma accelerators. The MHD model is used to study the plasma-surface impact interaction generated by the impingement of the jet on a target material plate. The study will characterize the extreme conditions generated on the target material surface by resolving the magnetized shock boundary layer interaction and the viscous/thermal diffusion effects. Additionally, since the plasma accelerator is operated in vacuum conditions, a novel plasma-vacuum interface tracking algorithm is developed to simulate the expansion of the high density plasma into a vacuum background in a physically consistent manner.

  5. SYNTHETIC SYNCHROTRON EMISSION MAPS FROM MHD MODELS FOR THE JET OF M87

    NARCIS (Netherlands)

    Gracia, J.; Vlahakis, N.; Agudo, I.; Tsinganos, K.; Bogovalov, S. V.

    2009-01-01

    We present self-consistent global steady state MHD models and synthetic optically thin synchrotron emission maps for the jet of M87. The model consists of two distinct zones: an inner relativistic outflow, which we identify with the observed jet, and an outer cold disk wind. While the former does no

  6. SYNTHETIC SYNCHROTRON EMISSION MAPS FROM MHD MODELS FOR THE JET OF M87

    NARCIS (Netherlands)

    Gracia, J.; Vlahakis, N.; Agudo, I.; Tsinganos, K.; Bogovalov, S. V.

    2009-01-01

    We present self-consistent global steady state MHD models and synthetic optically thin synchrotron emission maps for the jet of M87. The model consists of two distinct zones: an inner relativistic outflow, which we identify with the observed jet, and an outer cold disk wind. While the former does no

  7. Non-thermal atmospheric pressure plasma jet and its application for polymer treatment

    OpenAIRE

    Sarani, Abdollah

    2010-01-01

    Non-thermal atmospheric pressure plasma jet is a suitable source for polymer treatment. The main characteristic of this plasma jet is the remote operation and its scalable dimension, thus, allowing local treatment of 3D surfaces. In this work an atmospheric pressure DBD plasma jet has been constructed and the application of the plasma jet for polymer treatment is investigated.

  8. The effect of working gas impurities on plasma jets

    Energy Technology Data Exchange (ETDEWEB)

    Liu, X. Y.; He, M. B., E-mail: pulhmb@mail.hust.edu.cn [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, WuHan, HuBei 430074 (China); IFSA Collaborative Innovation Center, Shanghai Jiao Tong University, Shanghai 200240 (China); Liu, D. W. [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, WuHan, HuBei 430074 (China); IFSA Collaborative Innovation Center, Shanghai Jiao Tong University, Shanghai 200240 (China); State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an, Shanxi 710049 (China)

    2015-04-15

    Air intrusion reduced the purity of working gas inside the tube for plasma jet, and thereby, affected the discharge dynamics. In this paper, the effect of using working gas with different purity level (helium purity 99.99999%, 99.99%, 99.9%, and 99%) on photoionization and the chemical reactivity of plasma jet were studied using a 2 dimensional plasma jet model. Photoionization of air species acted as a source of pre-ionization in front of the ionization region, which facilitated the transition from localized discharge to streamers inside the tube. The density of reactive species inside the tube was found to increase with the concentration of working gas impurities. For the highest purity helium (99.99999%), despite a low photoionization rate and the distance between the photoionization region and ionization region inside the tube, by increasing the applied voltage and decreasing the distance between the electrode and nozzle, plasma jets were formed.

  9. Plasma performance of TFCX and JET with sawtoothing

    Energy Technology Data Exchange (ETDEWEB)

    Hively, L.M.; Mikkelsen, D.R.

    1984-11-01

    The plasma performance is assessed for two tokamak reactor experiments, the Tokamak Fusion Core Experiment (TFCX) and the Joint European Torus (JET). Both machines appear ignitable for a reasonable range of transport assumptions.

  10. Experimental characterization of an argon laminar plasma jet at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Langlois-Bertrand, Emilie; De Izarra, Charles, E-mail: charles.de_izarra@univ-orleans.fr [Groupe de Recherche sur l' Energetique des Milieux Ionises, UMR6606 Universite d' Orleans - CNRS, Faculte des Sciences, Site de Bourges, rue Gaston Berger, BP 4043, 18028 BOURGES Cedex (France)

    2011-10-19

    This paper deals with a dc laminar pure argon plasma jet operating at atmospheric pressure in ambient air that was experimentally studied in order to obtain temperature and velocity. Plasma jet temperature was evaluated by optical emission spectroscopy and the plasma jet velocity was determined by various methods using a pressure sensor. It is shown that the maximum plasma jet temperature is 15 000 K and the maximum plasma jet velocity is 250 m s{sup -1} at the plasma jet centre. Finally, a study of the ambient air amount entrained into the plasma jet is presented.

  11. The jet-stream channels of gas and plasma in atmospheric-pressure plasma jets

    Science.gov (United States)

    Cho, Guangsup; Kim, Yunjung; Uhm, Han Sup

    2016-08-01

    A solution to the fluid momentum equation for incompressible steady-state flow is obtained for the streams of gas and plasma inside a jet nozzle and in the open-air space. Three pressure forces are considered in the equation. The first is the pressure force of the shear stress resulting from the flow viscosity and is balanced against the second pressure force of the gas stream that is ejected into the air. The third pressure force is due to the radial expansion of the fluid channel, reducing the velocity of the fluid to zero so that we obtain the reaching distance of the fluid after ejection from the nozzle. From the solution for the fluid channel, the regional profile and the density profile of the plasma flow are also determined. The maximum distance of the gas flow with a critical Reynolds number of R nc ≈ 2000 is calculated to be 100 times that of the nozzle diameter for Ar, Ne, and He. Because the radial expansion of the plasma is ten times larger than that of neutral gases, the length of the plasma flume is a few tens of the nozzle diameter, which is significantly shorter than the gas flow distance. In the experiments, the maximum length of the plasma plume increases and then saturates as the operation voltage increases.

  12. Numerical investigation of heat transfer performance of synthetic jet impingement onto dimpled/protrusioned surface

    Directory of Open Access Journals (Sweden)

    Zhang Di

    2015-01-01

    Full Text Available Dynamic mesh methods and user defined functions are adopted and the shear stress transport k-ω turbulent model has been used in the numerical investigation of heat transfer performance of synthetic jet impingement onto dimple/protrusioned surface. The results show that the local time-averaged Nusselt number of the dimpled/protrusioned target surface tends to be much closer with that of flat cases with increasing of frequency. The heat transfer performance gets better when frequency increases. The area-averaged time-averaged Nusselt number of protrusioned target surface is the most close to that of flat cases when f = 320 Hz while it is the smallest among the synthetic jet cases in dimpled target surface. The heat transfer enhancement performance of synthetic jet is 30 times better than that of natural convection. The time-averaged Nusselt number of stagnation point in the protrusioned target surface is higher than that of flat target surface while it is lower in the dimpled surface than that of flat surface no matter in the synthetic jet, steady jet or natural convection cases. Meanwhile, the timeaveraged Nusselt number of stagnation point in the synthetic jet cases increases with the increasing of frequency. It is worth pointing out that the time-averaged Nusselt number of stagnation point is lower than that of steady cases when the frequency is low. However, it shows a bit higher than that of steady cases when f = 320 Hz.

  13. A 1D (radial) Plasma Jet Propagation Study for the Plasma Liner Experiment (PLX)

    Science.gov (United States)

    Thompson, J. R.; Bogatu, I. N.; Galkin, S. A.; Kim, J. S.; Welch, D. R.; Thoma, C.; Golovkin, I.; Macfarlane, J. J.; Case, A.; Messer, S. J.; Witherspoon, F. D.; Cassibry, J. T.; Awe, T. J.; Hsu, S. C.

    2011-10-01

    The Plasma Liner Experiment will explore the formation of imploding spherical ``plasma liners'' that reach peak pressures of 0.1 Mbar upon stagnation. The liners will be formed through the merging of dense, high velocity plasma jets (n ~1017 cm-3, T ~3 eV, v ~50 km/s) in a spherically convergent geometry. The focus of this 1D (radial) study is argon plasma jet evolution during propagation from the rail gun source to the jet merging radius. The study utilizes the Large Scale Plasma (LSP) PIC code with atomic physics included through the use of a non-Local Thermal Equilibrium (NLTE) Equation of State (EOS) table. We will present scenarios for expected 1D (radial) plasma jet evolution, from upon exiting the PLX rail gun to reaching the jet merging radius. The importance of radiation cooling early in the simulation is highlighted. Work supported by US DOE grant DE-FG02-05ER54835.

  14. Glottal jet measurements in synthetic, MRI-based human vocal fold models

    Science.gov (United States)

    Thomson, Scott; Pickup, Brian; Gollnick, Paul

    2007-11-01

    Human vocal fold vibration generates a time-varying elliptically-shaped glottal jet that produces sound in speech. Improved understanding of glottal jet dynamics can yield insight into voice production mechanisms and improve the diagnosis and treatment of voice disorders. Experiments using recently developed life-sized synthetic models of the vocal folds are presented. The fabrication process of converting MRI images to synthetic models is described. The process allows for varying the Young's modulus of the models, allowing for asymmetric conditions to be created by casting opposing vocal folds using materials of different stiffness. The models are shown to oscillate at frequencies, pressures, and flow rates typical of human speech. Phase-locked particle image velocimetry (PIV) results are presented which characterize the glottal jet, including jet direction, vortical structures, and turbulence levels. Results are shown for symmetric and asymmetric vocal fold models. The degree of material asymmetry required to cause significant asymmetry in the glottal jet is reported.

  15. Ideal magnetohydrodynamic simulations of unmagnetized dense plasma jet injection into a hot strongly magnetized plasma

    CERN Document Server

    Liu, Wei

    2010-01-01

    We present results from three-dimensional ideal magnetohydrodynamic simulations of unmagnetized dense plasma jet injection into a hot strongly magnetized plasma, with the aim of providing insight into core fueling of a tokamak with parameters relevant for ITER (International Thermonuclear Experimental Reactor) and NSTX (National Spherical Torus Experiment). Unmagnetized jet injection is similar to compact toroid injection but with higher possible injection density and total mass, as well as a potentially smaller footprint for the injector hardware. Our simulation results show that the unmagnetized dense jet is quickly magnetized upon injection. The penetration depth of the jet into the tokamak plasma is mostly dependent on the jet's initial kinetic energy while the jet's magnetic field determines its interior evolution. A key requirement for spatially precise fueling is for the jet's slowing-down time to be less than the time for the perturbed tokamak magnetic flux to relax due to magnetic reconnection. Thus ...

  16. Instability wave control in turbulent jet by plasma actuators

    Science.gov (United States)

    Kopiev, V. F.; Akishev, Y. S.; Belyaev, I. V.; Berezhetskaya, N. K.; Bityurin, V. A.; Faranosov, G. A.; Grushin, M. E.; Klimov, A. I.; Kopiev, V. A.; Kossyi, I. A.; Moralev, I. A.; Ostrikov, N. N.; Taktakishvili, M. I.; Trushkin, N. I.; Zaytsev, M. Yu

    2014-12-01

    Instability waves in the shear layer of turbulent jets are known to be a significant source of jet noise, which makes their suppression important for the aviation industry. In this study we apply plasma actuators in order to control instability waves in the shear layer of a turbulent air jet at atmospheric pressure. Three types of plasma actuators are studied: high-frequency dielectric barrier discharge, slipping surface discharge, and surface barrier corona discharge. Particle image velocimetry measurements of the shear layer demonstrate that the plasma actuators have control authority over instability waves and effectively suppress the instability waves artificially generated in the shear layer. It makes these actuators promising for application in active control systems for jet noise mitigation.

  17. Spectroscopic characterization of atmospheric pressure um-jet plasma source

    CERN Document Server

    Bibinov, Nikita; Bahre, Hendrik; Awakowicz, Peter; der Gathen, Volker Schulz-von

    2011-01-01

    A radio frequency um-jet plasma source is studied using He/O2 mixture. This um-jet can be used for different applications as a source of chemical active species e.g. oxygen atoms, molecular metastables and ozone. Using absolutely-calibrated optical emission spectroscopy and numerical simulation, the gas temperature in active plasma region and plasma parameters (electron density and electron distribution function) are determined. Concentrations of oxygen atoms and ozone in the plasma channel and in the effluent of the plasma source are measured using emission and absorption spectroscopy. To interpret the measured spatial distributions, the steady-state species' concentrations are calculated using determined plasma parameters and gas temperature. At that the influence of the surface processes and gas flow regime on the loss of the active species in the plasma source are discussed. The measured spatial distributions of oxygen atom and ozone densities are compared with the simulated ones.

  18. Gas Flow and Electric Field Characterization in Plasma Jets for Biomedical Applications: From Single Jet to Multi Jet Arrays

    Science.gov (United States)

    Robert, Eric

    2015-09-01

    This work reports first on time-resolved measurement of longitudinal and radial electric fields (EF) associated with plasma propagation in dielectric capillaries. Plasma propagation occurs in a region where longitudinal EF exists ahead the ionization front position revealed from plasma emission with ICCD measurement. The ionization front propagation induces the sudden rise of a radial EF component. Both of these EF components have a few kV/cm in amplitude for helium or neon plasmas. Their amplitude is kept almost constant along a few tens of cm long capillary. The key role of the voltage pulse polarity and the drastic impact of the presence of a target in front of the plasma jet are discussed from Schlieren images. All these experimental measurements are in excellent agreement with model calculations which are used to infer EF data on capillary axis. EF diagnostics in the plasma plume in the free jet mode but also in contact with various targets is proposed. The combination of intense transient EF, both of ns and µs duration, together with significant transient reactive species generation during plasma jet treatments may be reconsidered. Typical EF amplitudes likely to induce electrostimulation, electroporation are indeed probably achieved in many in vivo protocols. Stimulation of tissue oxygenation, blood flow rate modulation and more recently immune system triggering may be examples where EF could play a significant role. The second part of this work is dedicated to the development of multi jets, using two different setups, based on a single plasma source. Plasma splitting in dielectric tubes drilled with sub millimetric orifices, but also plasma transfer across metallic tubes equipped with such orifices are analyzed from ICCD imaging and time resolved EF measurements. This allows for the design of plasma jet arrays but also emphasizes the necessity to account for voltage pulse polarity, target potential status, consecutive helium flow modulation and

  19. Experimental approaches for studying non-equilibrium atmospheric plasma jets

    Energy Technology Data Exchange (ETDEWEB)

    Shashurin, A., E-mail: ashashur@purdue.edu [School of Aeronautics & Astronautics, Purdue University, West Lafayette, Indiana 47907 (United States); Keidar, M. [Department of Mechanical and Aerospace Engineering, The George Washington University, Washington, District of Columbia 20052 (United States)

    2015-12-15

    This work reviews recent research efforts undertaken in the area non-equilibrium atmospheric plasma jets with special focus on experimental approaches. Physics of small non-equilibrium atmospheric plasma jets operating in kHz frequency range at powers around few Watts will be analyzed, including mechanism of breakdown, process of ionization front propagation, electrical coupling of the ionization front with the discharge electrodes, distributions of excited and ionized species, discharge current spreading, transient dynamics of various plasma parameters, etc. Experimental diagnostic approaches utilized in the field will be considered, including Rayleigh microwave scattering, Thomson laser scattering, electrostatic streamer scatterers, optical emission spectroscopy, fast photographing, etc.

  20. Cold atmospheric plasma jet in an axial DC electric field

    Science.gov (United States)

    Lin, Li; Keidar, Michael

    2016-08-01

    Cold atmospheric plasma (CAP) jet is currently intensively investigated as a tool for new and potentially transformative cancer treatment modality. However, there are still many unknowns about the jet behavior that requires attention. In this paper, a helium CAP jet is tested in an electrostatic field generated by a copper ring. Using Rayleigh microwave scattering method, some delays of the electron density peaks for different ring potentials are observed. Meanwhile, a similar phenomenon associated with the bullet velocity is found. Chemical species distribution along the jet is analyzed based on the jet optical emission spectra. The spectra indicate that a lower ring potential, i.e., lower DC background electric field, can increase the amount of excited N2, N2+, He, and O in the region before the ring, but can decrease the amount of excited NO and HO almost along the entire jet. Combining all the results above, we discovered that an extra DC potential mainly affects the temporal plasma jet properties. Also, it is possible to manipulate the chemical compositions of the jet using a ring with certain electric potentials.

  1. Efficiency enhancement in transonic compressor rotor blades using synthetic jets: A numerical investigation

    Energy Technology Data Exchange (ETDEWEB)

    Benini, Ernesto; Biollo, Roberto; Ponza, Rita [Department of Mechanical Engineering - University of Padova, Via Venezia, 1 - 35131 Padova (Italy)

    2011-03-15

    Several passive and active techniques were studied and developed by compressor designers with the aim of improving the aerodynamic behavior of compressor blades by reducing, or even eliminating, flow separation. Fluidic-based methods, in particular, have been investigated for a long time, including both steady and unsteady suction, blowing and oscillating jets. Recently, synthetic jets (zero mass flux) have been proposed as a promising solution to reduce low-momentum fluid regions inside turbomachines. Synthetic jets, with the characteristics of zero net mass flux and non-zero momentum flux, do not require a complex system of pumps and pipes. They could be very efficient because at the suction part of the cycle the low-momentum fluid is sucked into the device, whereas in the blowing part a high-momentum jet accelerates it. To the authors' knowledge, the use of synthetic jets has never been experimented in transonic compressor rotors, where this technique could be helpful (i) to reduce the thickness and instability of blade suction side boundary layer after the interaction with the shock, and (ii) to delay the arising of the low-momentum region which can take place from the shock-tip clearance vortex interaction at low flow operating conditions, a flow feature which is considered harmful to rotor stability. Therefore, synthetic jets could be helpful to improve both efficiency and stall margin in transonic compressor rotors. In this paper, an accurate and validated CFD model is used to simulate the aerodynamic behavior of a transonic compressor rotor with and without synthetic jets. Four technical solutions were evaluated, different for jet position and velocity, and one was investigated in detail. (author)

  2. Interactions of a finite span synthetic jet with a cross flow

    Science.gov (United States)

    Leong, Chia Min; van Buren, Tyler; Whalen, Edward; Amitay, Michael; Rensselaer Polytechnic Institute Team; Boeing Collaboration

    2013-11-01

    A synthetic jet is a zero-net-mass-flux flow control actuator that produces alternating ejection and suction of fluid momentum across an orifice. It has been used in numerous applications as an active flow control device to improve aerodynamic performance. Though their aerodynamic performance effects are well known, this present study seeks to understand the fluid dynamic effects of synthetic jets. Specifically, the work investigates the interactions of a finite span synthetic jet with a zero-pressure-gradient laminar boundary layer. This study was performed in a small-scale subsonic wind tunnel with an adjustable test section upper wall that was used to generate a zero-pressure-gradient boundary layer. Several finite span rectangular orifices were chosen for this study. Time and phase-averaged Stereoscopic Particle Image Velocimetry (SPIV) measurements were acquired at multiple planes upstream and downstream of the synthetic jet orifice to explore the interaction of the synthetic jet with the cross flow. The effects of the orifice aspect ratio (12, 18, and 24) and blowing ratio (0.5, 1, and 1.5) were investigated. The unsteady vortical structures observed in the near field and the steady structures in the far field are discussed.

  3. Dust generation at interaction of plasma jet with surfaces

    Science.gov (United States)

    Ticos, Catalin; Toader, Dorina; Banu, Nicoleta; Scurtu, Adrian; Oane, Mihai

    2013-10-01

    Coatings of W and C with widths of a few microns will be exposed to plasma jet for studying the erosion of the surface and detachment of micron size dust particles. A coaxial plasma gun has been built inside a vacuum chamber for producing supersonic plasma jets. Its design is based on a 50 kJ coaxial plasma gun which has been successfully used for accelerating hypervelocity dust. Initial shots were carried out for a capacitor bank with C = 12 μF and charged up to 2 kV. Currents of tens of amps were measured with a Rogowsky coil and plasma flow speeds of 4 km/s were inferred from high-speed images of jet propagation. An upgrade consisting in adding capacitors in parallel will be performed in order to increase the energy up to 2 kJ. A coil will be installed at the gun muzzle to compress the plasma flow and increase the energy density of the jet on the sample surface. A CCD camera with a maximum recording speed of 100 k fps and a maximum resolution of 1024 × 1024 pixels was set for image acquisition of the plasma and dust. A laser system used to illuminate the ejected dust from the surface includes a laser diode emitting at 650 nm with a beam power of 25 mW. The authors acknowledge support from EURATOM WP13-IPH-A03-P2-02-BS22.

  4. Dynamics of apokamp-type atmospheric pressure plasma jets

    Science.gov (United States)

    Sosnin, Eduard A.; Panarin, Victor A.; Skakun, Victor S.; Baksht, Evgeny Kh.; Tarasenko, Victor F.

    2017-02-01

    The paper describes a new discharge source of atmospheric pressure plasma jets (APPJs) in air with no gas supply through the discharge region. In this discharge mode, plasma jets develop from the bending point of a bright current channel between two electrodes and are therefore termed an apokamp (from Greek `off' and `bend'). The apokamp can represent single plasma jets of length up 6 cm or several jets, and the temperature of such jets can range from more than 1000 °C at their base to 100-250 °C at their tip. Apokamps are formed at maximum applied voltage of positive polarity, provided that the second electrode is capacitively decoupled with ground. According to high-speed photography with time resolution from several nanoseconds to several tens of nanoseconds, the apokamp consists of a set of plasma bullets moving with a velocity of 100-220 km/s, which excludes the convective mechanism of plasma decay. Estimates on a 100-ns scale show that the near-electrode zones and the zones from which apokamps develop are close in temperature.

  5. Magnetohydrodynamic simulation study of plasma jets and plasma-surface contact in coaxial plasma accelerators

    Science.gov (United States)

    Subramaniam, Vivek; Raja, Laxminarayan L.

    2017-06-01

    Recent experiments by Loebner et al. [IEEE Trans. Plasma Sci. 44, 1534 (2016)] studied the effect of a hypervelocity jet emanating from a coaxial plasma accelerator incident on target surfaces in an effort to mimic the transient loading created during edge localized mode disruption events in fusion plasmas. In this paper, we present a magnetohydrodynamic (MHD) numerical model to simulate plasma jet formation and plasma-surface contact in this coaxial plasma accelerator experiment. The MHD system of equations is spatially discretized using a cell-centered finite volume formulation. The temporal discretization is performed using a fully implicit backward Euler scheme and the resultant stiff system of nonlinear equations is solved using the Newton method. The numerical model is employed to obtain some key insights into the physical processes responsible for the generation of extreme stagnation conditions on the target surfaces. Simulations of the plume (without the target plate) are performed to isolate and study phenomena such as the magnetic pinch effect that is responsible for launching pressure pulses into the jet free stream. The simulations also yield insights into the incipient conditions responsible for producing the pinch, such as the formation of conductive channels. The jet-target impact studies indicate the existence of two distinct stages involved in the plasma-surface interaction. A fast transient stage characterized by a thin normal shock transitions into a pseudo-steady stage that exhibits an extended oblique shock structure. A quadratic scaling of the pinch and stagnation conditions with the total current discharged between the electrodes is in qualitative agreement with the results obtained in the experiments. This also illustrates the dominant contribution of the magnetic pressure term in determining the magnitude of the quantities of interest.

  6. Development of A Pulse Radio-Frequency Plasma Jet

    Science.gov (United States)

    Wang, Shou-Guo; Zhao, Ling-Li; Yang, Jing-Hua

    2013-09-01

    A small pulse plasma jet was driven by new developed radio-frequency (RF) power supply of 6.78 MHz. In contrast to the conventional RF 13.56 MHz atmospheric pressure plasma jet (APPJ), the power supply was highly simplified by eliminating the matching unit of the RF power supply and using a new circuit, moreover, a pulse controller was added to the circuit to produce the pulse discharge. The plasma jet was operated in a capacitively coupled manner and exhibited low power requirement of 5 W at atmospheric pressure using argon as a carrier gas. The pulse plasma plume temperature remained at less than 45 °C for an extended period of operation without using water to cool the electrodes. Optical emission spectrum measured at a wide range of 200-1000 nm indicated various excited species which were helpful in applying the plasma jet for surface sterilization to human skin or other sensitive materials. Institude of Plasma Physics, Chinese Academy of Science, Hefei, China.

  7. Schlieren Cinematography of Current Driven Plasma Jet Dynamics

    Science.gov (United States)

    Loebner, Keith; Underwood, Thomas; Cappelli, Mark

    2016-10-01

    Schlieren cinematography of a pulsed plasma deflagration jet is presented and analyzed. An ultra-high frame rate CMOS camera coupled to a Z-type laser Schlieren apparatus is used to obtain flow-field refractometry data for the continuous flow Z-pinch formed within the plasma deflagration jet. The 10 MHz frame rate for 256 consecutive frames provides high temporal resolution, enabling turbulent fluctuations and plasma instabilities to be visualized over the course of a single pulse (20 μs). The Schlieren signal is radiometrically calibrated to obtain a two dimensional mapping of the refraction angle of the axisymmetric pinch plasma, and this mapping is then Abel inverted to derive the plasma density distribution as a function radius, axial coordinate, and time. Analyses of previously unknown discharge characteristics and comparisons with prior work are discussed.

  8. Flow control in axial fan inlet guide vanes by synthetic jets

    OpenAIRE

    Wurst P.; Trávníček Z.; Cyrus V.; Kordík J.

    2013-01-01

    Tested high pressure axial flow fan with hub/tip ratio of 0.70 and external diameter of 600 mm consisted of inlet guide vanes (IGV), rotor and stator blade rows. Fan peripheral velocity was 47 m/s. Air volume flow rate was changed by turning of rear part of the inlet guide vanes. At turning of 20 deg the flow was separated on the IGV profiles. The synthetic jets were introduced through radial holes in machine casing in the location before flow separation origin. Synthetic jet actuator was des...

  9. Acoustic signature analysis of the interaction between a dc plasma jet and a suspension liquid jet

    Energy Technology Data Exchange (ETDEWEB)

    Rat, V; Coudert, J F [SPCTS-CNRS UMR 6638, University of Limoges, 123 av. A Thomas 87060 Limoges cedex (France)

    2009-10-07

    Suspension plasma spraying allows forming finely structured coatings by injecting suspensions of ceramic particles within a dc plasma jet. The electric arc motion in dc plasma torch is the main acoustic source which is modified by the injection of suspension. The analyses of cross-correlations between the arc voltage and the acoustic signal show a decrease in time propagations due to local cooling of the plasma jet when injecting suspensions. Moreover, power spectra highlight acoustic amplifications below a certain frequency threshold and attenuations above. A simplified model of the frequency acoustic response of a two-phase vaporizing mixture is used to interpret experimental measurements. These acoustic effects are due to the dynamics of thermal transfers between vaporizing liquid and plasma.

  10. Driving Flows in Laboratory Astrophysical Plasma Jets: The Mochi.LabJet Experiment

    Science.gov (United States)

    Carroll, Evan G.

    Mochi.Labjet is a new experiment at the University of Washington developed to investigate the interaction of shear flows in plasma jets with boundary conditions similar to an accretion disc system. This thesis details the engineering design and first plasmas of the Mochi.Labjet experiment. The experiment required construction of a new three electrode plasma gun with azimuthal symmetric gas injection, two optically-isolated pulsed power supplies for generating and sustaining plasma, and one optically-isolated pulsed power supply for generating a background magnetic field. Optical isolation is achieved with four custom circuits: the TTL-optical transmitter, optical-TTL receiver, optical-relay, and optical-tachometer circuits. First plasmas, during the commissioning phase of the apparatus, show evidence of flared jet structures with significant azimuthal symmetry.

  11. Generation of Diffuse Large Volume Plasma by an Ionization Wave from a Plasma Jet

    Science.gov (United States)

    Laroussi, Mounir; Razavi, Hamid

    2015-09-01

    Low temperature plasma jets emitted in ambient air are the product of fast ionization waves that are guided within a channel of a gas flow, such as helium. This guided ionization wave can be transmitted through a dielectric material and under some conditions can ignite a discharge behind the dielectric material. Here we present a novel way to produce large volume diffuse low pressure plasma inside a Pyrex chamber that does not have any electrodes or electrical energy directly applied to it. The diffuse plasma is ignited inside the chamber by a plasma jet located externally to the chamber and that is physically and electrically unconnected to the chamber. Instead, the plasma jet is just brought in close proximity to the external wall/surface of the chamber or to a dielectric tubing connected to the chamber. The plasma thus generated is diffuse, large volume and with physical and chemical characteristics that are different than the external plasma jet that ignited it. So by using a plasma jet we are able to ``remotely'' ignite volumetric plasma under controlled conditions. This novel method of ``remote'' generation of a low pressure, low temperature diffuse plasma can be useful for various applications including material processing and biomedicine.

  12. Surface modification of polymeric materials by cold atmospheric plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Kostov, K.G., E-mail: kostov@feg.unesp.br [Faculty of Engineering in Guaratinguetá–FEG, Universidade Estadual Paulista–UNESP Guaratiguetá, 12516-410, SP (Brazil); Nishime, T.M.C.; Castro, A.H.R. [Faculty of Engineering in Guaratinguetá–FEG, Universidade Estadual Paulista–UNESP Guaratiguetá, 12516-410, SP (Brazil); Toth, A. [Institute of Material and Environmental Chemistry, Hungarian Academy of Science P.O. Box 17, H-1525, Budapest (Hungary); Hein, L.R.O. [Faculty of Engineering in Guaratinguetá–FEG, Universidade Estadual Paulista–UNESP Guaratiguetá, 12516-410, SP (Brazil)

    2014-09-30

    Highlights: • We investigate polymer surface modification by atmospheric pressure plasma jet APPJ. • Jet operation conditions for uniform surface modification were determined. • The APPJ added O atoms to the polymer surface and also enhanced the roughness. • The degree of polymer surface modification by APPJ and DBD were compared. • The APPJ is more efficient in attaching O atoms and produces less polymer fragments. - Abstract: In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source – the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40° in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure.

  13. Polymerization of acrylic acid using atmospheric pressure DBD plasma jet

    Science.gov (United States)

    Bashir, M.; Bashir, S.

    2016-08-01

    In this paper polymerization of acrylic acid was performed using non thermal atmospheric pressure plasma jet technology. The goal of this study is to deposit organic functional coatings for biomedical applications using a low cost and rapid growth rate plasma jet technique. The monomer solution of acrylic acid was vaporized and then fed into the argon plasma for coating. The discharge was powered using a laboratory made power supply operating with sinusoidal voltage signals at a frequency of 10 kHz. The optical emission spectra were collected in order to get insight into the plasma chemistry during deposition process. The coatings were characterized using Fourier transform infrared spectroscopy, atomic force microscopy and growth rates analysis. A high retention of carboxylic functional groups of the monomer was observed at the surface deposited using this low power technique.

  14. Numerical Simulations of Collisionless Shock Formation in Merging Plasma Jet Experiments

    Science.gov (United States)

    2013-06-01

    experiment [5], which uses counter-propagating hydrogen plasma jets formed and launched by plasma railguns [11] mounted on opposite sides of a...hydrogen plasma jet propagating from the railgun nozzle to the center of the chamber in order to connect the plasma jet parameters at the railgun exit...the jet at the railgun exit and center of the chamber (z = 0 cm) are given in Table 1. So this simulation determines the approximate parameter regime

  15. Capillary plasma jet: A low volume plasma source for life science applications

    Energy Technology Data Exchange (ETDEWEB)

    Topala, I., E-mail: ionut.topala@uaic.ro, E-mail: tmnagat@ipc.shizuoka.ac.jp [Alexandru Ioan Cuza University of Iasi, Faculty of Physics, Iasi Plasma Advanced Research Center (IPARC), Bd. Carol I No. 11, Iasi 700506 (Romania); Nagatsu, M., E-mail: ionut.topala@uaic.ro, E-mail: tmnagat@ipc.shizuoka.ac.jp [Graduate School of Science and Technology, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561 (Japan)

    2015-02-02

    In this letter, we present results from multispectroscopic analysis of protein films, after exposure to a peculiar plasma source, i.e., the capillary plasma jet. This plasma source is able to generate very small pulsed plasma volumes, in kilohertz range, with characteristic dimensions smaller than 1 mm. This leads to specific microscale generation and transport of all plasma species. Plasma diagnosis was realized using general electrical and optical methods. Depending on power level and exposure duration, this miniature plasma jet can induce controllable modifications to soft matter targets. Detailed discussions on protein film oxidation and chemical etching are supported by results from absorption, X-ray photoelectron spectroscopy, and microscopy techniques. Further exploitation of principles presented here may consolidate research interests involving plasmas in biotechnologies and plasma medicine, especially in patterning technologies, modified biomolecule arrays, and local chemical functionalization.

  16. Active aeroelastic control aspects of an aircraft wing by using synthetic jet actuators: modeling, simulations, experiments

    NARCIS (Netherlands)

    Donnell, K.O.; Schober, S.; Stolk, M.; Marzocca, P.; De Breuker, R.; Abdalla M.; Nicolini, E.; Gürdal, Z.

    2007-01-01

    This paper discusses modeling, simulations and experimental aspects of active aeroelastic control on aircraft wings by using Synthetic Jet Actuators (SJAs). SJAs, a particular class of zero-net mass-flux actuators, have shown very promising results in numerous aeronautical applications, such as boun

  17. Water Spray Flow Characteristics Under Synthetic Jet Driven By a Piezoelectric Actuator

    Science.gov (United States)

    Marchitto, L.; Valentino, G.; Chiatto, M.; de Luca, L.

    2017-01-01

    Particle Image Velocimetry (PIV) and Phase Doppler Anemometry (PDA) have been applied to investigate the droplets size and velocity distribution of a water spray, under the control of a piezo-element driven synthetic jet (SJ). Tests were carried out under atmospheric conditions within a chamber test rig equipped with optical accesses at two injection pressures, namely 5 and 10 MPa, exploring the variation of the main spray parameters caused by the synthetic jet perturbations. The SJ orifice has been placed at 45° with respect to the water spray axis; the nozzle body has been moved on its own axis and three different nozzle quotes were tested. PIV measurements have been averaged on 300 trials whereas about 105 samples have been acquired for the PDA tests. For each operative condition, the influence region of the SJ device on the spray has been computed through a T-Test algorithm. The synthetic jet locally interacts with the spray, energizing the region downstream the impact. The effect of the actuator decreases at higher injection pressures and moving the impact region upwards. Droplets coalescence can be detected along the synthetic jet axis, while no significant variations are observed along a direction orthogonal to it.

  18. Active aeroelastic control aspects of an aircraft wing by using synthetic jet actuators: modeling, simulations, experiments

    NARCIS (Netherlands)

    Donnell, K.O.; Schober, S.; Stolk, M.; Marzocca, P.; De Breuker, R.; Abdalla M.; Nicolini, E.; Gürdal, Z.

    2007-01-01

    This paper discusses modeling, simulations and experimental aspects of active aeroelastic control on aircraft wings by using Synthetic Jet Actuators (SJAs). SJAs, a particular class of zero-net mass-flux actuators, have shown very promising results in numerous aeronautical applications, such as

  19. Experimental investigation of thermal characteristics of synthetic jet generator's diaphragm with piezoelectric actuator

    Science.gov (United States)

    Rimasauskiene, Ruta; Rimasauskas, Marius; Mieloszyk, Magdalena; Wandowski, Tomasz; Malinowski, Pawel; Ostachowicz, Wieslaw

    2014-05-01

    An experimental analysis of the thermal characteristics of two different diaphragms of the synthetic jet generator was presented in this paper. It is extremely important to study temperature characteristics of the components with piezoelectric actuators working in various modes. Often piezoelectric actuators are used aiming to obtain maximum displacements that are possible when a piezoelectric actuator operates under maximum excitation voltage and often at the first resonance frequency. The theory suggests that working in such modes extremely increases temperature of the piezoelectric elements and it can reach maximum point. High temperatures might cause deformation or other changes of mechanical properties of the other components. This might influence the life time and operational characteristics of the synthetic jet generator. The main task of this work was to find the best working conditions for the synthetic jet generator. Dynamic characteristics of the diaphragm with piezoelectric material were measured using non-contact measuring equipment laser vibrometer Polytec® PSV 400. Temperatures of the piezoelectric diaphragms working at different resonance frequencies were measured with Fiber Bragg Grating (FBG) sensor. Experimental results of two different piezoelectric diaphragms were presented in this article. The best working conditions for synthetic jet generator were chosen.

  20. Impinging jet study of the deposition of colloidal particles on synthetic polymer (Zeonor)

    DEFF Research Database (Denmark)

    Vlček, Jakub; Lapčík, Lubomír; Cech, Jiri

    2014-01-01

    In this study, an impinging jet deposition experiments were performed on synthetic polymer (Zeonor) original and by micro-embossing modified substrates with exactly defined topology as confirmed by AFM and SEM. Deposition experiments were performed at ambient temperature and at selected flow regime...

  1. Interaction of a finite-span synthetic jet near the tip of a sweptback wing

    Science.gov (United States)

    Vasile, Joseph D.; Amitay, Michael

    2015-06-01

    An experimental investigation was performed to study the three-dimensional flow interaction of a finite-span (aspect ratio of 18) synthetic jet located near the tip of a sweptback wing (cross-sectional profile of NACA 4421, aspect ratio of 4, and sweep angle of 30°) at a Reynolds number of 105 and at three angles of attack of 0°, 9°, and 15.5° (covering the range of attached to separated flow in the vicinity of the synthetic jet). Three blowing ratios were considered as 0.8, 1.2, and 2. Stereoscopic particle image velocimetry data were collected at multiple 2-D planes in the vicinity of the jet's orifice, which were then used to reconstruct the flow volume, and the effect of the jet's blowing ratio was analyzed using time-averaged and phase-averaged statistics. The study showed that the flow field in the vicinity of the synthetic jet orifice becomes highly three-dimensional and is governed by the streamwise structures that are associated with the finite span of the orifice (edge vortices). Furthermore, it was demonstrated that the baseline flow field that develops over a swept-back configuration (characterized by spanwise and streamwise vorticity components) is responsible for the immediate breakdown of the coherent structures that are introduced by the synthetic jet orifice and for the formation of the secondary flow structures that were seen in the time-averaged flow field. Moreover, the presence of a tip vortex results in the development of a non-uniform (in the spanwise direction) spanwise boundary layer that becomes more pronounced with increasing angle of attack. Consequently, the development of the flow structures is altered. Finally, the present work suggests that the location of the synthetic jet along the span is not as important (as the angle of attack and the blowing ratio) in the overall formation and evolution of the flow structures issued from the jet. However, the size and strength of these structures are affected by the jet's spanwise location.

  2. Discharge effects on gas flow dynamics in a plasma jet

    Science.gov (United States)

    Xian, Yu Bin; Hasnain Qaisrani, M.; Yue, Yuan Fu; Lu, Xin Pei

    2016-10-01

    Plasma is used as a flow visualization method to display the gas flow of a plasma jet. Using this method, it is found that a discharge in a plasma jet promotes the transition of the gas flow to turbulence. A discharge at intermediate frequency (˜6 kHz in this paper) has a stronger influence on the gas flow than that at lower or higher frequencies. Also, a higher discharge voltage enhances the transition of the gas flow to turbulence. Analysis reveals that pressure modulation induced both by the periodically directed movement of ionized helium and Ohmic heating on the gas flow plays an important role in inducing the transition of the helium flow regime. In addition, since the modulations induced by the high- and low-frequency discharges are determined by the frequency-selective effect, only intermediate-frequency (˜6 kHz) discharges effectively cause the helium flow transition from the laminar to the turbulent flow. Moreover, a discharge with a higher applied voltage makes a stronger impact on the helium flow because it generates stronger modulations. These conclusions are useful in designing cold plasma jets and plasma torches. Moreover, the relationship between the discharge parameters and the gas flow dynamics is a useful reference on active flow control with plasma actuators.

  3. Surface modification of polymeric materials by cold atmospheric plasma jet

    Science.gov (United States)

    Kostov, K. G.; Nishime, T. M. C.; Castro, A. H. R.; Toth, A.; Hein, L. R. O.

    2014-09-01

    In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source - the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40° in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure.

  4. Experimental tests for carbon nanomaterial synthesis using DC plasma jet

    Science.gov (United States)

    Lange, H.; Łabȩdź, O.; Tylska, I.; Huczko, A.; Bystrzejewski, M.

    2014-11-01

    In the frame of this work some experimental tests were performed in the plasma jet. Pure ethanol vapour alone or with the addition of fine iron powder were used to synthesize few-layer graphene or carbon-encapsulated iron nanoparticles, respectively.

  5. Degradation of tungsten under the action of a plasma jet

    Science.gov (United States)

    Voronin, A. V.; Sud'enkov, Yu. V.; Semenov, B. N.; Atroshenko, S. A.; Naumova, N. S.

    2014-07-01

    The degradation of the surface and structure of single-crystal tungsten and sintered powder tungsten during the action of a pulsed plasma jet is studied. It is shown that the degradation of a tungsten target during the action of a plasma jet with an energy flux density of 0.25-1 MJ/m2 is accompanied by surface evaporation and melting and the fracture of surface layers on scales of 150-250 μm. The results of a numerical simulation of the thermomechanical processes that occur in a tungsten target during the action of a plasma jet are presented. The degradation of tungsten during the action of a plasma jet is shown to proceed almost continuously from the action (evaporation, melting) to the times that are more than three orders of magnitude longer than the action time, which is caused by the thermomechanical processes occurring in the tungsten target. Moreover, the action of thermal stresses leads to structural and morphological changes throughout the sample volume, and these changes are accompanied by recrystallization in adiabatic shear bands.

  6. Laboratory Plasma Source as an MHD Model for Astrophysical Jets

    Science.gov (United States)

    Mayo, Robert M.

    1997-01-01

    The significance of the work described herein lies in the demonstration of Magnetized Coaxial Plasma Gun (MCG) devices like CPS-1 to produce energetic laboratory magneto-flows with embedded magnetic fields that can be used as a simulation tool to study flow interaction dynamic of jet flows, to demonstrate the magnetic acceleration and collimation of flows with primarily toroidal fields, and study cross field transport in turbulent accreting flows. Since plasma produced in MCG devices have magnetic topology and MHD flow regime similarity to stellar and extragalactic jets, we expect that careful investigation of these flows in the laboratory will reveal fundamental physical mechanisms influencing astrophysical flows. Discussion in the next section (sec.2) focuses on recent results describing collimation, leading flow surface interaction layers, and turbulent accretion. The primary objectives for a new three year effort would involve the development and deployment of novel electrostatic, magnetic, and visible plasma diagnostic techniques to measure plasma and flow parameters of the CPS-1 device in the flow chamber downstream of the plasma source to study, (1) mass ejection, morphology, and collimation and stability of energetic outflows, (2) the effects of external magnetization on collimation and stability, (3) the interaction of such flows with background neutral gas, the generation of visible emission in such interaction, and effect of neutral clouds on jet flow dynamics, and (4) the cross magnetic field transport of turbulent accreting flows. The applicability of existing laboratory plasma facilities to the study of stellar and extragalactic plasma should be exploited to elucidate underlying physical mechanisms that cannot be ascertained though astrophysical observation, and provide baseline to a wide variety of proposed models, MHD and otherwise. The work proposed herin represents a continued effort on a novel approach in relating laboratory experiments to

  7. Observation of plasma jets in a table top plasma focus discharge

    Energy Technology Data Exchange (ETDEWEB)

    Pavez, Cristian; Soto, Leopoldo, E-mail: lsoto@cchen.cl [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Center for Research and Applications in Plasma Physics and Pulsed Power, P4, Santiago-Talca (Chile); Departamento de Ciencias Físicas, Facultad de Ciencias Exactas, Universidad Andrés Bello, República 220, Santiago (Chile); Pedreros, José [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Departamento de Ingeniería Eléctrica, Universidad de Santiago de Chile, Santiago (Chile); Tarifeño-Saldivia, Ariel [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Center for Research and Applications in Plasma Physics and Pulsed Power, P4, Santiago-Talca (Chile)

    2015-04-15

    In the last years, medium size Z-pinch experiments operating at tens of kJ are being used to create supersonic plasma jets. Those experiments are produced with wire arrays and radial foils, and they are conducted in generators based on water-filled transmission lines. Also plasma jets have been observed in small X-pinch experiments operating at 1 kJ. In this work, observations of plasma jets produced in a table top plasma focus device by means of optical and digital interferometry are shown. The device was operated at only ∼70 J, achieving 50 kA in 150 ns. The plasma jets were observed after the pinch, in the region close and on the anode, along the axis. The electron density measured from the jets is in the range 10{sup 24}–10{sup 25 }m{sup −3}. From two consecutive plasma images separated 18 ns, the axial jet velocity was measured in the order of 4 × 10{sup 4 }m/s.

  8. Simulation of triton burn-up in JET plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Loughlin, M.J.; Balet, B.; Jarvis, O.N.; Stubberfield, P.M. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking

    1994-07-01

    This paper presents the first triton burn-up calculations for JET plasmas using the transport code TRANSP. Four hot ion H-mode deuterium plasmas are studied. For these discharges, the 2.5 MeV emission rises rapidly and then collapses abruptly. This phenomenon is not fully understood but in each case the collapse phase is associated with a large impurity influx known as the ``carbon bloom``. The peak 14 MeV emission occurs at this time, somewhat later than that of the 2.5 MeV neutron peak. The present results give a clear indication that there are no significant departures from classical slowing down and spatial diffusion for tritons in JET plasmas. (authors). 7 refs., 3 figs., 1 tab.

  9. Axial Plasma Jet Characterization on a Microsecond X-Pinch

    Science.gov (United States)

    Jaar, G. S.; Appartaim, R. K.

    2016-10-01

    The plasma jets generated from a two wire x-pinch have been studied with current quarter period of 1 μs. Wires of tungsten, aluminum, and titanium of 25-100 μm thicknesses have been exploded with a peak current value of 350kA. The plasma has been characterized using Nd:YAG based schlieren photography, time-resolved optical photography, x-ray photodiode detector, and a flat crystal x-ray spectrometer. The schlieren photographs enable determination of the evolution and velocity of the jets. Plasma temperature and density measurements at the crossing point will also be reported from the crystal spectrometer. This research is supported by the US DOE.

  10. Evolution of vectoring control of a primary jet with synthetic jets%合成射流控制主流矢量的发展过程

    Institute of Scientific and Technical Information of China (English)

    罗振兵; 夏智勋; 王德全; 胡建新; 缪万波; 黄利亚

    2008-01-01

    合成射流激励器射流矢量控制具有对吸气式发动机进气道出流和发动机喷管流动进行矢量控制的潜力.通过对四种不同出口构型合成射流激励器控制主流矢量偏转的数值模拟和分析,对合成射流控制主流矢量的发展过程进行了研究.结果表明:合成射流控制主流矢量的发展过程可分为三个不同阶段,第一阶段,在主流通道内,激励器工作引起的主流通道压强梯度形成的侧向力致偏主流,在出口处主流矢量偏转φⅠ;第二阶段,在主流出口附近,合成射流对主流的卷吸作用和引射作用,致偏主流φⅡ;第三阶段,在出口下游,合成射流与主流自由剪切层发生相互耦合作用,致偏φⅢ.因此,主射流最终偏转角度咖是其在经历三个不同阶段时受到的合成射流致偏作用之和,即φ=φⅠ+φⅡ+φⅢ.%The technique of jet vectoring using synthetic jets has a potential ability of thrust vectoring a primary jet,such as thrust vectoring controlling the inlet air jet and the nozzle jet of the air-breathing engine.To investigate the evolution of vectoring control of a primary jet with synthetic jets,a primary jet vectoring control using synthetic jet actuators with different exit configurations was numerically simulated and analyzed.The results show the evolution of jet vectoring using synthetic jets is divided into three stages.In the conduit of the primary jet,the low-pressure region,which results from the interaction between the synthetic jet and the primary jet,contributes to the vectoring force and leads to a turning of the primary jet at the conduit exit,and the primary jet turns φⅠ.And then,in the near field,the primary jet fluid is entrained and absorbed by the synthetic jet during the blowing and the suction stroke,and the primary jet turns φⅡ.Finally,in the far field,the shear layer of primary jet is inspirited by the vortices of synthetic jet,and the primary jet turns φⅢ.So the final

  11. An Atmospheric Large-Scale Cold Plasma Jet

    Institute of Scientific and Technical Information of China (English)

    吕晓桂; 任春生; 马腾才; 冯岩; 王德真

    2012-01-01

    This letter reports on the generation and characteristics of a large-scale dielectric barrier discharge plasma jet at atmospheric pressure. With appropriate parameters, diffuse plasma with a 50×5 mm2 cross-sectional area is obtained. The characteristics of the discharges are diag- nosed by using electrical and optical methods. In addition to being generated in helium, plasma is also generated in a mixed gas of helium and oxygen. The oxygen atomic radiant intensity (3p5P→ 3s5S, 3p3P→3s3S transition) is not proportional to the proportion of oxygen in the gas mixture, as shown by the experimental results.

  12. Characterization of thermal and current quench of JET plasmas

    Science.gov (United States)

    Riccardo, V.; Barabaschi, P.; Loarte, A.; Sugihara, M.

    2004-11-01

    JET provides crucial scaling points and unique physics access for the extrapolation of disruptions to ITER. Disruption and ELM heat loads influence the selection of materials for plasma facing components (PFCs). Most JET thermal quenches occur when the plasma thermal energy is less than half that at full performance, suggesting a more optimistic life expectancy for ITER PFCs. The exceptions are ITB collapses and pure VDEs, which are also more likely to lead to the shortest thermal quenches. For the fast current quench disruptions, the EM load due to the induced eddy currents represent the most severe electromechanical design condition for in-vessel components. The minimum linear decay time normalised to the plasma cross section extrapolates to a 40 ms disruption for ITER, based on data from JET and most other tokamaks. Some very fast JET events are better fit by an exponential, with the minimum characteristic current decay time scaling to 35 ms for ITER. Contrary to expectations, the quench rate of high and low thermal energy disruptions does not vary substantially.

  13. Fast ions and momentum transport in JET tokamak plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Salmi, A.

    2012-07-01

    Fast ions are an inseparable part of fusion plasmas. They can be generated using electromagnetic waves or injected into plasmas as neutrals to heat the bulk plasma and to drive toroidal rotation and current. In future power plants fusion born fast ions deliver the main heating into the plasma. Understanding and controlling the fast ions is of crucial importance for the operation of a power plant. Furthermore, fast ions provide ways to probe the properties of the thermal plasma and get insight of its confinement properties. In this thesis, numerical code packages are used and developed to simulate JET experiments for a range of physics issues related to fast ions. Namely, the clamping fast ion distribution at high energies with RF heating, fast ion ripple torque generation and the toroidal momentum transport properties using NBI modulation technique are investigated. Through a comparison of numerical simulations and the JET experimental data it is shown that the finite Larmor radius effects in ion cyclotron resonance heating are important and that they can prevent fast ion tail formation beyond certain energy. The identified mechanism could be used for tailoring the fast ion distribution in future experiments. Secondly, ASCOT simulations of NBI ions in a ripple field showed that most of the reduction of the toroidal rotation that has been observed in the JET enhanced ripple experiments could be attributed to fast ion ripple torque. Finally, fast ion torque calculations together with momentum transport analysis have led to the conclusion that momentum transport in not purely diffusive but that a convective component, which increases monotonically in radius, exists in a wide range of JET plasmas. Using parameter scans, the convective transport has been shown to be insensitive to collisionality and q-profile but to increase strongly against density gradient. (orig.)

  14. Coal-derived carbon nanotubes by thermal plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Y.; Zhang, Y.L.; Wang, B.J.; Ji, W.J.; Zhang, Y.F.; Xie, K.C. [Nanjing University, Nanjing (China). Dept. of Physics

    2004-07-01

    A coal/arc-jet technique by directly and successively injecting coal fine particles into the arc plasma jet instead of arcing graphite or coal-based electrodes for producing carbon nanotubes (CNTs) from coal was developed. The derived carbon products by this technique were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), high-resolution TEM (HRTEM), X-ray energy dispersive spectrum (EDS), X-ray diffraction (XRD) and Raman spectrum. The experimental results clearly indicated that certain metal catalysts favored the growth of CNTs in the process, and the relevant growth mechanism was discussed in terms of the characterizations.

  15. Design and construction of triplet atmospheric cold plasma jet for sterilization

    Directory of Open Access Journals (Sweden)

    F. Sohbatzadeh

    2014-03-01

    Full Text Available In this paper, construction of triplet atmospheric plasma jet using argon, air, oxygen and nitrogen gases is reported. Bactericidal effect of the plasma jet is also investigated. To that end, longitudinal geometric configuration for the electrodes was chosen because it would increase the jet length. Electrical characteristics, jet length dependencies on the applied voltage and gas flow rate were decided, experimentally. Relative concentrations of chemical reactive species such as ozone, atomic oxygen, NOx compounds and hydroxyl were measured using optical emission spectroscopy. It was seen that atomic oxygen and ozone concentrations with triplet plasma jet are more than the concentration of single plasma jet. Triplet plasma jet was also used for sterilization of solid and liquid surfaces to disinfect gram-negative and gram-positive Escherichia coli and Streptococcus pyogenes bacteria. The results verified the effectiveness of the triplet plasma jet for killing bacteria.

  16. Plasma jet printing for flexible substrates

    Science.gov (United States)

    Gandhiraman, Ram P.; Singh, Eric; Diaz-Cartagena, Diana C.; Nordlund, Dennis; Koehne, Jessica; Meyyappan, M.

    2016-03-01

    Recent interest in flexible electronics and wearable devices has created a demand for fast and highly repeatable printing processes suitable for device manufacturing. Robust printing technology is critical for the integration of sensors and other devices on flexible substrates such as paper and textile. An atmospheric pressure plasma-based printing process has been developed to deposit different types of nanomaterials on flexible substrates. Multiwalled carbon nanotubes were deposited on paper to demonstrate site-selective deposition as well as direct printing without any type of patterning. Plasma-printed nanotubes were compared with non-plasma-printed samples under similar gas flow and other experimental conditions and found to be denser with higher conductivity. The utility of the nanotubes on the paper substrate as a biosensor and chemical sensor was demonstrated by the detection of dopamine, a neurotransmitter, and ammonia, respectively.

  17. Plasma jet printing for flexible substrates

    Energy Technology Data Exchange (ETDEWEB)

    Gandhiraman, Ram P.; Singh, Eric; Diaz-Cartagena, Diana C.; Koehne, Jessica; Meyyappan, M. [Center for Nanotechnology, NASA Ames Research Center, Moffett Field, California 94035 (United States); Nordlund, Dennis [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States)

    2016-03-21

    Recent interest in flexible electronics and wearable devices has created a demand for fast and highly repeatable printing processes suitable for device manufacturing. Robust printing technology is critical for the integration of sensors and other devices on flexible substrates such as paper and textile. An atmospheric pressure plasma-based printing process has been developed to deposit different types of nanomaterials on flexible substrates. Multiwalled carbon nanotubes were deposited on paper to demonstrate site-selective deposition as well as direct printing without any type of patterning. Plasma-printed nanotubes were compared with non-plasma-printed samples under similar gas flow and other experimental conditions and found to be denser with higher conductivity. The utility of the nanotubes on the paper substrate as a biosensor and chemical sensor was demonstrated by the detection of dopamine, a neurotransmitter, and ammonia, respectively.

  18. On non-equilibrium atmospheric pressure plasma jets and plasma bullet

    Science.gov (United States)

    Lu, Xinpei

    2012-10-01

    Because of the enhanced plasma chemistry, atmospheric pressure nonequilibrium plasmas (APNPs) have been widely studied for several emerging applications such as biomedical applications. For the biomedical applications, plasma jet devices, which generate plasma in open space (surrounding air) rather than in confined discharge gaps only, have lots of advantages over the traditional dielectric barrier discharge (DBD) devices. For example, it can be used for root canal disinfection, which can't be realized by the traditional plasma device. On the other hand, currently, the working gases of most of the plasma jet devices are noble gases or the mixtures of the noble gases with small amount of O2, or air. If ambient air is used as the working gas, several serious difficulties are encountered in the plasma generation process. Amongst these are high gas temperatures and disrupting instabilities. In this presentation, firstly, a brief review of the different cold plasma jets developed to date is presented. Secondly, several different plasma jet devices developed in our lab are reported. The effects of various parameters on the plasma jets are discussed. Finally, one of the most interesting phenomena of APNP-Js, the plasma bullet is discussed and its behavior is described. References: [1] X. Lu, M. Laroussi, V. Puech, Plasma Sources Sci. Technol. 21, 034005 (2012); [2] Y. Xian, X. Lu, S. Wu, P. Chu, and Y. Pan, Appl. Phys. Lett. 100, 123702 (2012); [3] X. Pei, X. Lu, J. Liu, D. Liu, Y. Yang, K. Ostrikov, P. Chu, and Y. Pan, J. Phys. D 45, 165205 (2012).

  19. Numerical Computation and Investigation of the Characteristics of Microscale Synthetic Jets

    Directory of Open Access Journals (Sweden)

    Ann Lee

    2011-01-01

    Full Text Available A synthetic jet results from periodic oscillations of a membrane in a cavity. Jet is formed when fluid is alternately sucked into and ejected from a small cavity by the motion of membrane bounding the cavity. A novel moving mesh algorithm to simulate the formation of jet is presented. The governing equations are transformed into the curvilinear coordinate system in which the grid velocities evaluated are then fed into the computation of the flow in the cavity domain thus allowing the conservation equations of mass and momentum to be solved within the stationary computational domain. Numerical solution generated using this moving mesh approach is compared with an experimental result measuring the instantaneous velocity fields obtained by μPIV measurements in the vicinity of synthetic jet orifice 241 μm in diameter issuing into confined geometry. Comparisons between experimental and numerical results on the streamwise component of velocity profiles at the orifice exit and along the centerline of the pulsating jet in microchannel as well as the location of vortex core indicate that there is good agreement, thereby demonstrating that the moving mesh algorithm developed is valid.

  20. SDBD plasma jet for skin disinfection

    NARCIS (Netherlands)

    Creyghton, Y.L.M.; Meijer, S.R.; Verweij, P.E.; Zanden, F. van der; Leenders, P.H.M.

    2011-01-01

    A consortium consisting of the research institute TNO, the medical university and hospital St Radboud and two industrial enterprises is working on a non-thermal plasma treatment method for skin and wound disinfection. The group is seeking for cooperation, in particular in the field of validation

  1. SDBD plasma jet for skin disinfection

    NARCIS (Netherlands)

    Creyghton, Y.L.M.; Meijer, S.R.; Verweij, P.E.; Zanden, F. van der; Leenders, P.H.M.

    2011-01-01

    A consortium consisting of the research institute TNO, the medical university and hospital St Radboud and two industrial enterprises is working on a non-thermal plasma treatment method for skin and wound disinfection. The group is seeking for cooperation, in particular in the field of validation met

  2. Atmospheric-pressure plasma jet induces apoptosis involving mitochondria via generation of free radicals.

    Directory of Open Access Journals (Sweden)

    Hak Jun Ahn

    Full Text Available The plasma jet has been proposed as a novel therapeutic method for anticancer treatment. However, its biological effects and mechanism of action remain elusive. Here, we investigated its cell death effects and underlying molecular mechanisms, using air and N₂ plasma jets from a micro nozzle array. Treatment with air or N₂ plasma jets caused apoptotic death in human cervical cancer HeLa cells, simultaneously with depolarization of mitochondrial membrane potential. In addition, the plasma jets were able to generate reactive oxygen species (ROS, which function as surrogate apoptotic signals by targeting the mitochondrial membrane potential. Antioxidants or caspase inhibitors ameliorated the apoptotic cell death induced by the air and N₂ plasma jets, suggesting that the plasma jet may generate ROS as a proapoptotic cue, thus initiating mitochondria-mediated apoptosis. Taken together, our data suggest the potential employment of plasma jets as a novel therapy for cancer.

  3. Atmospheric-pressure plasma jet induces apoptosis involving mitochondria via generation of free radicals.

    Science.gov (United States)

    Ahn, Hak Jun; Kim, Kang Il; Kim, Geunyoung; Moon, Eunpyo; Yang, Sang Sik; Lee, Jong-Soo

    2011-01-01

    The plasma jet has been proposed as a novel therapeutic method for anticancer treatment. However, its biological effects and mechanism of action remain elusive. Here, we investigated its cell death effects and underlying molecular mechanisms, using air and N₂ plasma jets from a micro nozzle array. Treatment with air or N₂ plasma jets caused apoptotic death in human cervical cancer HeLa cells, simultaneously with depolarization of mitochondrial membrane potential. In addition, the plasma jets were able to generate reactive oxygen species (ROS), which function as surrogate apoptotic signals by targeting the mitochondrial membrane potential. Antioxidants or caspase inhibitors ameliorated the apoptotic cell death induced by the air and N₂ plasma jets, suggesting that the plasma jet may generate ROS as a proapoptotic cue, thus initiating mitochondria-mediated apoptosis. Taken together, our data suggest the potential employment of plasma jets as a novel therapy for cancer.

  4. A new method for fluid input into a hybrid synthetic jet actuator

    Directory of Open Access Journals (Sweden)

    Kordík J.

    2014-03-01

    Full Text Available A new principle of flow rectification for hybrid synthetic jet actuators is introduced in this paper. As is well known, the flow rectification can be best accomplished by means of fluidic diodes. Novelty of the present study are fluidic diodes with two mutually opposed nozzles. Interaction between the periodic jet flows from the nozzles causes a difference between the blowing and suction strokes, resulting in a particularly efficient rectification effect. The distance between the nozzle exits as well as the oscillation frequency were the parameters, which were varied during hot-wire measurements. The combination of those parameters achieving the highest volumetric effciency was identified.

  5. Experiments with an rf dusty plasma and an external plasma jet

    Science.gov (United States)

    Ticoş, C. M.

    2010-12-01

    A plasma jet produced in a coaxial plasma gun was aimed at a cloud of dust particles levitated in the sheath of a radio-frequency (rf) plasma produced between two parallel-plate electrodes. A high-speed camera with a side-view on the dust cloud was used to track the dust particles. Several cases of dust motion could be observed. When the jet was parallel with the horizontal electrodes of the rf plasma the dust particles were either pushed out of the trapping region by the plasma jet or were only perturbed from their equilibrium position, oscillating with a frequency of the order of a few kHz. In the first case the trajectory of the dust particles followed the curvature of the sheath. In the second case, when the jet was fired at a small angle with the horizontal electrodes the dust particles hit the bottom electrode and ricocheted back into the sheath. Finally, another situation was observed when the jet perturbed the rf plasma and its sheath and the whole dust crystal fell to the electrode.

  6. Multiple Pulses from Plasma Jets onto Liquid Covered Tissue

    Science.gov (United States)

    Norberg, Seth; Tian, Wei; Johnsen, Eric; Kushner, Mark J.

    2014-10-01

    Atmospheric pressure plasma jets are being studied in the treatment of biological surfaces that are often covered by a thin layer of liquid. The plume of the plasma jet contains neutral radicals and charged species that solvate into the liquid and eventually form terminal species that reach the tissue below. The contribution of neutral and charged species to reactivity in the liquid is sensitive to whether the active plasma plume touches the liquid. In this paper, we discuss results from modeling the production of the aqueous species formed from the interaction of the plume of plasma jets over multiple pulses with the water layer, and the fluences of the species to the underlying tissue. The model used in this study, nonPDPSIM, solves transport equations for charged and neutral species and electron energy, Poisson's equation for the electric potential, and Navier-Stokes equations for the neutral gas flow. Radiation transport includes photoionization of O2 and H2O in the gas and liquid phases and photodissocation of H2Oaq in the liquid. Multiple pulses when the plasma plume touches and does not touch the liquid will be examined. Two regimes of hydrodynamics will be discussed - low repetition rates where the neutral radicals are blown away before the next discharge pulse, and high repetition rate when the plasma plume interacts with neutral radicals from previous pulses. The density of aqueous ions produced in the liquid layer is strongly dependent on whether the plasma effluent touches or does not touch the water surface. Work supported by DOE Office of Fusion Energy Science and NSF.

  7. Laser plasma jet driven microparticles for DNA/drug delivery.

    Directory of Open Access Journals (Sweden)

    Viren Menezes

    Full Text Available This paper describes a microparticle delivery device that generates a plasma jet through laser ablation of a thin metal foil and uses the jet to accomplish particle delivery into soft living targets for transferring biological agents. Pure gold microparticles of 1 µm size were coated with a plasmid DNA, pIG121Hm, and were deposited as a thin layer on one surface of an aluminum foil. The laser (Nd:YAG, 1064 nm wavelength ablation of the foil generated a plasma jet that carried the DNA coated particles into the living onion cells. The particles could effectively penetrate the target cells and disseminate the DNA, effecting the transfection of the cells. Generation of the plasma jet on laser ablation of the foil and its role as a carrier of microparticles was visualized using a high-speed video camera, Shimadzu HPV-1, at a frame rate of 500 kfps (2 µs interframe interval in a shadowgraph optical set-up. The particle speed could be measured from the visualized images, which was about 770 m/s initially, increased to a magnitude of 1320 m/s, and after a quasi-steady state over a distance of 10 mm with an average magnitude of 1100 m/s, started declining, which typically is the trend of a high-speed, pulsed, compressible jet. Aluminum launch pad (for the particles was used in the present study to make the procedure cost-effective, whereas the guided, biocompatible launch pads made of gold, silver or titanium can be used in the device during the actual clinical operations. The particle delivery device has a potential to have a miniature form and can be an effective, hand-held drug/DNA delivery device for biological applications.

  8. Spectroscopic studies of the parameters of plasma jets during their propagation in the background plasma on the PF-3 facility

    Science.gov (United States)

    Dan’ko, S. A.; Ananyev, S. S.; Kalinin, Yu G.; Krauz, V. I.; Myalton, V. V.

    2017-04-01

    This paper presents measurement results of neon and helium plasma parameters in axial jets generated in plasma focus discharge. They were obtained in the course of experiments on laboratory modeling of astrophysical jets performed at the PF-3 facility. The plasma concentration was determined according to Stark broadening of spectral lines; the ionization temperature was determined by the average ion charge. The values of the concentration and temperature of jet plasma and background plasma at two distances from the pinch are also presented. In addition, an estimation was made of the heat content losses of the neon and helium jets during their movement through the surrounding medium.

  9. Tendency of spherically imploding plasma liners formed by merging plasma jets to evolve toward spherical symmetry

    CERN Document Server

    Cassibry, J T; Hsu, S C; Abarzhi, S I; Witherspoon, F D

    2012-01-01

    Three dimensional hydrodynamic simulations have been performed using smoothed particle hydrodynamics (SPH) in order to study the effects of discrete jets on the processes of plasma liner formation, implosion on vacuum, and expansion. The pressure history of the inner portion of the liner was qualitatively and quantitatively similar from peak compression through the complete stagnation of the liner among simulation results from two one dimensional radiationhydrodynamic codes, 3D SPH with a uniform liner, and 3D SPH with 30 discrete plasma jets. Two dimensional slices of the pressure show that the discrete jet SPH case evolves towards a profile that is almost indistinguishable from the SPH case with a uniform liner, showing that non-uniformities due to discrete jets are smeared out by late stages of the implosion. Liner formation and implosion on vacuum was also shown to be robust to Rayleigh-Taylor instability growth. Interparticle mixing for a liner imploding on vacuum was investigated. The mixing rate was ve...

  10. Study of coal conversion in an arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Xie, K.C.; Lu, Y.K.; Tian, Y.J.; Wang, D.Z. [Taiyuan University of Technology, Taiyuan (China)

    2002-12-01

    Coal conversion in arc plasma with an initial temperature of 3700 K is complex; a new conversion mechanism is put forward in this article. The functions of pyrolysis and the interaction of active species containing plasma jets are the main factors for coal conversion under these conditions. This study indicates that when the coal feed rate is lower than 2.0 g/s, both pyrolysis and active species have evident contribution to coal conversion; the pyrolysis controls the coal conversion and the function of active species is very weak. It is also found that the coal feed rate has a large influence on coal conversion and the production of gas components.

  11. Simulation of coal pyrolysis in plasma jet by CPD model

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Y.; Xie, K.; Zhu, S.; Fletcher, T.H. [Taiyuan University of Technology, Taiyuan (China). State Key Lab. of C1 Chemistry and Technology

    2001-12-01

    Reaction of coal in a plasma jet is complex and extremely rapid, and acetylene and carbon monoxide are the main products in the pyrolysis gas. Coal pyrolysis is assumed as the first step reaction when coal is injected into hot plasma jet with initial average temperature of 3700 K. Chemical percolation devolatalization (CPD) is employed first to simulate this procedure in mechanism. The calculation results indicate coal pyrolysis rate in plasma jet is very fast and the retention time of coal staying in reactor is only several milliseconds. Comparing the calculation with experiment result, it was concluded that the CPD agree with the experiment well when the coal feed rate is larger than about 2.0 g s{sup -1}. As the coal feed rate was increased, the average temperature of coal particle during staying in reactor was reduced and the residual time became long, but it was not found that the residual time influenced the coal conversion evidently. 15 refs., 6 figs., 3 tabs.

  12. Robust Nonlinear Regulation of Limit Cycle Oscillations in UAVs Using Synthetic Jet Actuators

    OpenAIRE

    Natalie Ramos Pedroza; William MacKunis; Golubev, Vladimir V.

    2014-01-01

    In this paper, a synthetic jet actuators (SJA)-based nonlinear robust controller is developed, which is capable of completely suppressing limit cycle oscillations (LCO) in UAV systems with parametric uncertainty in the SJA dynamics and unmodeled external disturbances. Specifically, the control law compensates for uncertainty in an input gain matrix, which results from the unknown airflow dynamics generated by the SJA. Challenges in the control design include compensation for input-multiplicat...

  13. Bacteria Inactivation Using DBD Plasma Jet in Atmospheric Pressure Argon

    Institute of Scientific and Technical Information of China (English)

    XU Guimin; ZHANG Guanjun; SHI Xingmin; MA Yue; WANG Ning; LI Yuan

    2009-01-01

    A coaxial dielectric barrier discharge plasma jet Was designed,which can be operated in atmospheric pressure argon under an intermediate frequency sinusoidal resonant power supply,and an atmospheric pressure glow-like discharge Was achieved.Two kinds of typical bacteria,i.e.,the Staphylococcus aureus(S.aurens)and Escherichia coil(E.coil),were employed to study the bacterial inactivation mechanism by means of the non-thermal plasma.The killing log value (KLV)of S.aureus reached up to 5.38 with a treatment time of 90 s and that of E.coil up to 5.36 with 60 s,respectively.According to the argon emission spectra of the plasma jet and the scanning electron microscope (SEM) images of the two bacteria before and after the plasma treatment.it is concluded that the reactive species in the argon plasma played a major role in the bacterial inactivation,while the heat,electric field and UV photons had little effect.

  14. Atmospheric pressure plasma jet treatment of Salmonella Enteritidis inoculated eggshells.

    Science.gov (United States)

    Moritz, Maike; Wiacek, Claudia; Koethe, Martin; Braun, Peggy G

    2017-03-20

    Contamination of eggshells with Salmonella Enteritidis remains a food safety concern. In many cases human salmonellosis within the EU can be traced back to raw or undercooked eggs and egg products. Atmospheric pressure plasma is a novel decontamination method that can reduce a wide range of pathogens. The aim of this work was to evaluate the possibility of using an effective short time cold plasma treatment to inactivate Salmonella Enteritidis on the eggshell. Therefore, artificially contaminated eggshells were treated with an atmospheric pressure plasma jet under different experimental settings with various exposure times (15-300s), distances from the plasma jet nozzle to the eggshell surface (5, 8 or 12mm), feed gas compositions (Ar, Ar with 0.2, 0.5 or 1.0% O2), gas flow rates (5 and 7slm) and different inoculations of Salmonella Enteritidis (10(1)-10(6)CFU/cm(2)). Atmospheric pressure plasma could reduce Salmonella Enteritidis on eggshells significantly. Reduction factors ranged between 0.22 and 2.27 log CFU (colony-forming units). Exposure time and, particularly at 10(4)CFU/cm(2) inoculation, feed gas had a major impact on Salmonella reduction. Precisely, longer exposure times led to higher reductions and Ar as feed gas was more effective than ArO2 mixtures.

  15. Diagnostics of atmospheric pressure capillary DBD oxygen plasma jet

    CERN Document Server

    Roy, N C; Pramanik, B K

    2015-01-01

    Atmospheric pressure capillary dielectric barrier oxygen discharge plasma jet is developed to generate non-thermal plasma using unipolar positive pulse power supply. Both optical and electrical techniques are used to investigate the characteristics of the produced plasma as function of applied voltage and gas flow rate. Analytical results obtained from the optical emission spectroscopic data reveal the gas temperature, rotational temperature, excitation temperature and electron density. Gas temperature and rotational temperature are found to decrease with increasing oxygen flow rate but increase linearly with applied voltage. It is exposed that the electron density is boosting up with enhanced applied voltage and oxygen flow rate, while the electron excitation temperature is reducing with rising oxygen flow rate. Electrical characterization demonstrates that the discharge frequency is falling with flow rate but increasing with voltage. The produced plasma is applied preliminarily to study the inactivation yie...

  16. Flow control in axial fan inlet guide vanes by synthetic jets

    Directory of Open Access Journals (Sweden)

    Wurst P.

    2013-04-01

    Full Text Available Tested high pressure axial flow fan with hub/tip ratio of 0.70 and external diameter of 600 mm consisted of inlet guide vanes (IGV, rotor and stator blade rows. Fan peripheral velocity was 47 m/s. Air volume flow rate was changed by turning of rear part of the inlet guide vanes. At turning of 20 deg the flow was separated on the IGV profiles. The synthetic jets were introduced through radial holes in machine casing in the location before flow separation origin. Synthetic jet actuator was designed with the use of a speaker by UT AVCR. Its membrane had diameter of 63 mm. Excitation frequency was chosen in the range of 500 Hz – 700 Hz. Synthetic jets favourably influenced separated flow on the vane profiles in the distance of (5 – 12 mm from the casing surface. The reduction of flow separation area caused in the region near the casing the decrease of the profile loss coefficient approximately by 20%.

  17. Flow control in axial fan inlet guide vanes by synthetic jets

    Science.gov (United States)

    Cyrus, V.; Trávníček, Z.; Wurst, P.; Kordík, J.

    2013-04-01

    Tested high pressure axial flow fan with hub/tip ratio of 0.70 and external diameter of 600 mm consisted of inlet guide vanes (IGV), rotor and stator blade rows. Fan peripheral velocity was 47 m/s. Air volume flow rate was changed by turning of rear part of the inlet guide vanes. At turning of 20 deg the flow was separated on the IGV profiles. The synthetic jets were introduced through radial holes in machine casing in the location before flow separation origin. Synthetic jet actuator was designed with the use of a speaker by UT AVCR. Its membrane had diameter of 63 mm. Excitation frequency was chosen in the range of 500 Hz - 700 Hz. Synthetic jets favourably influenced separated flow on the vane profiles in the distance of (5 - 12) mm from the casing surface. The reduction of flow separation area caused in the region near the casing the decrease of the profile loss coefficient approximately by 20%.

  18. Dynamics of Magnetized Plasma Jets and Bubbles Launched into a Background Magnetized Plasma

    Science.gov (United States)

    Wallace, B.; Zhang, Y.; Fisher, D. M.; Gilmore, M.

    2016-10-01

    The propagation of dense magnetized plasma, either collimated with mainly azimuthal B-field (jet) or toroidal with closed B-field (bubble), in a background plasma occurs in a number of solar and astrophysical cases. Such cases include coronal mass ejections moving in the background solar wind and extragalactic radio lobes expanding into the extragalactic medium. Understanding the detailed MHD behavior is crucial for correctly modeling these events. In order to further the understanding of such systems, we are investigating the injection of dense magnetized jets and bubbles into a lower density background magnetized plasma using a coaxial plasma gun and a background helicon or cathode plasma. In both jet and bubble cases, the MHD dynamics are found to be very different when launched into background plasma or magnetic field, as compared to vacuum. In the jet case, it is found that the inherent kink instability is stabilized by velocity shear developed due to added magnetic tension from the background field. In the bubble case, rather than directly relaxing to a minimum energy Taylor state (spheromak) as in vacuum, there is an expansion asymmetry and the bubble becomes Rayleigh-Taylor unstable on one side. Recent results will be presented. Work supported by the Army Research Office Award No. W911NF1510480.

  19. Transferred plasma jet from a dielectric barrier discharge for processing of poly(dimethylsiloxane) surfaces

    CERN Document Server

    Nascimento, Fellype do; Canesqui, Mara A; Moshkalev, Stanislav

    2016-01-01

    In this work we studied processing of poly(dimethylsiloxane) (PDMS) surfaces using dielectric barrier discharge (DBD) plasma in two different assemblies, one using the primary plasma jet obtained from a conventional DBD and the other using a DBD plasma jet transfer. The evolution of water contact angle (WCA) in function of plasma processing time and in function of aging time as well as the changes in the surface roughness of PDMS samples for both plasma treatments have been studied. We also compared vibrational and rotational temperatures for both plasmas and for the first time the vibrational temperature (T_vib) for the transferred plasma jet has been shown to be higher as compared with the primary jet. The increment in the T_vib value seems to be the main reason for the improvements in adhesion properties and surface wettability for the transferred plasma jet. Possible explanations for the increase in the vibrational temperature are presented.

  20. Study on an Atmospheric Pressure Plasma Jet and its Application in Etching Photo-Resistant Materials

    Institute of Scientific and Technical Information of China (English)

    李海江; 王守国; 赵玲利; 叶甜春

    2004-01-01

    An atmospheric pressure radio-frequency plasma jet that can eject cold plasma has been developed. In this paper, the configuration of this type of plasma jet is illustrated and its discharge characteristics curves are studied with a current and a voltage probe. A thermal couple is used to measure the temperature distribution along the axis of the jet stream. The temperature distribution curve is generated for the He/O2 jet stream at the discharge power of 150W. This jet can etch the photo-resistant material at an average rate of 100nm/min on the surface of silicon wafers at a right angle.

  1. Flute growth rate of plasma jet in mirror machine

    Science.gov (United States)

    Be'ery, I.; Seemann, O.; Goldstein, G.; Fisher, A.; Ron, A.

    2014-02-01

    The evolution of flute instability in a cold, high-density hydrogen plasma jet, injected into a mirror machine, is studied. The experiment was designed to minimize the interaction of the plasma with the walls, thus bringing it close to the ideal magnetic Rayleigh-Taylor instability conditions. The modal growth rate was measured in various settings to demonstrate the effects of the finite Larmor radius, Bohm diffusion, conductive limiter, biased limiter and neutral background gas. In this paper we will demonstrate that lowering the magnetic field increases stability, as does the insertion of a conducting ring. However, if the ring is biased, the stability is reduced due to inhomogeneous coupling between the plasma and the limiter. It was also found that heavy background gas dramatically reduces the flute instability growth rate.

  2. Action of plasma jets of a low-current spark discharge on microorganisms ( Escherichia coli)

    Science.gov (United States)

    Baldanov, B. B.; Semenov, A. P.; Ranzhurov, Ts. V.; Nikolaev, E. O.; Gomboeva, S. V.

    2015-11-01

    High efficiency of bactericide action of cold argon plasma generated by plasma jets of a weak-current spark discharge under atmospheric pressure is demonstrated. It is found that an increase in the time of treatment with plasma jets from a low-current spark discharge makes it possible to effectively inactivate microorganisms over a much larger area.

  3. Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

    Science.gov (United States)

    Zhai, Guofu; Bo, Kai; Chen, Mo; Zhou, Xue; Qiao, Xinlei

    2016-05-01

    Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit. We characterized the arc plasma jet flow appearance at different currents by using high-speed photography, and two polished contacts were used to search for the relationship between roughness and plasma jet flow. Then, to make the nature of arc plasma jet flow phenomena clear, a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated. The simulated DC arc plasma was presented with the temperature distribution and the current density distribution. Furthermore, the calculated arc flow velocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress. The combined action of volume force and contact surface was the main reason of the arc jet flow. supported by National Natural Science Foundation of China (Nos. 51307030, 51277038)

  4. Investigation on Plasma Jet Flow Phenomena During DC Air Arc Motion in Bridge-Type Contacts

    Institute of Scientific and Technical Information of China (English)

    ZHAI Guofu; BO Kai; CHEN Mo; ZHOU Xue; QIAO Xinlei

    2016-01-01

    Arc plasma jet flow in the air was investigated under a bridge-type contacts in a DC 270 V resistive circuit.We characterized the arc plasma jet flow appearance at different currents by using high-speed photography,and two polished contacts were used to search for the relationship between roughness and plasma jet flow.Then,to make the nature of arc plasma jet flow phenomena clear,a simplified model based on magnetohydrodynamic (MHD) theory was established and calculated.The simulated DC arc plasma was presented with the temperature distribution and the current density distribution.Furthermore,the calculated arc flow vclocity field showed that the circular vortex was an embodiment of the arc plasma jet flow progress.The combined action of volume force and contact surface was the main reason of the arc jet flow.

  5. Pulsating jet-like structures in magnetized plasma

    Science.gov (United States)

    Goncharov, V. P.; Pavlov, V. I.

    2016-08-01

    The formation of pulsating jet-like structures has been studied in the scope of the nonhydrostatic model of a magnetized plasma with horizontally nonuniform density. We discuss two mechanisms which are capable of stopping the gravitational spreading appearing to grace the Rayleigh-Taylor instability and to lead to the formation of stationary or oscillating localized structures. One of them is caused by the Coriolis effect in the rotating frames, and another is connected with the Lorentz effect for magnetized fluids. Magnetized jets/drops with a positive buoyancy must oscillate in transversal size and can manifest themselves as "radio pulsars." The estimates of their frequencies are made for conditions typical for the neutron star's ocean.

  6. Collisional current drive in two interpenetrating plasma jets

    Energy Technology Data Exchange (ETDEWEB)

    Ryutov, D. D.; Kugland, N. L.; Park, H.-S.; Pollaine, S. M.; Remington, B. A.; Ross, J. S. [Lawrence Livermore National Laboratory, Livermore, California 94551 (United States)

    2011-10-15

    The magnetic field generation in two interpenetrating, weakly collisional plasma streams produced by intense lasers is considered. The generation mechanism is very similar to the neutral beam injection current drive in toroidal fusion devices, with the differences related to the absence of the initial magnetic field, short interaction time, and different geometry. Spatial and temporal characteristics of the magnetic field produced in two counterstreaming jets are evaluated; it is shown that the magnetic field of order of 1 T can be generated for modest jet parameters. Conditions under which this mechanism dominates that of the ''Biermann battery'' are discussed. Other settings where the mechanism of the collisional current drive can be important for the generation of seed magnetic fields include astrophysics and interiors of hohlraums.

  7. Experimental Studies of Low-Pressure Plasma Jet by Means of Langmuir Probes and Emission Spectra

    Institute of Scientific and Technical Information of China (English)

    LIU Lei; CAO Jinxiang; NIU Tianye; WANG Liang; MENG Gang; LIU Xin; YUAN Lei; WU Runhui; ZHANG Shengjun; REN Aimin

    2009-01-01

    An investigation was made into the argon plasma jet that expanded in a low-pressure vacuum chamber. The spatial distributions of the parameters of the plasma jet with different supplied powers were measured using a ten-channel Langmuir probe array. The chemical species in the plasma jet were identified by emission spectroscopy. The electron excitation temperatures at two positions, 10 cm and 50 cm downstream from the nozzle exit were calculated, respectively, by the Boltzmann plot method.

  8. Synthetic synchrotron emission maps from MHD models for the jet of M87

    CERN Document Server

    Gracia, J; Agudo, I; Tsinganos, K; Bogovalov, S V

    2009-01-01

    We present self-consistent global, steady-state MHD models and synthetic optically thin synchrotron emission maps for the jet of M87. The model consist of two distinct zones: an inner relativistic outflow, which we identify with the observed jet, and an outer cold disk-wind. While the former does not self-collimate efficiently due to its high effective inertia, the latter fulfills all the conditions for efficient collimation by the magneto-centrifugal mechanism. Given the right balance between the effective inertia of the inner flow and the collimation efficiency of the outer disk wind, the relativistic flow is magnetically confined into a well collimated beam and matches the measurements of the opening angle of M87 over several orders of magnitude in spatial extent. The synthetic synchrotron maps reproduce the morphological structure of the jet of M87, i.e. center-bright profiles near the core and limb-bright profiles away from the core. At the same time, they also show a local increase of brightness at some...

  9. Physics and Chemistry of MW Laser-induced Discharge in Gas Flows and Plasma Jets

    Science.gov (United States)

    2007-12-01

    can be quasi-stationary coaxial plasma accelerators (MPC). This type of accelerators generates plasma jets of different gases (H2, He, N2, Ar) with...gas is ionizing and accelerating in discharge processing. For this regime the plasma gun generates the plasma jets of different gases3 (H2, He, N2...spectrometers. Spectrometers 1 and 2 are used for measuring of time behavior of single spectral lines, emitting in the focus area of plasma gun . Usually

  10. Nonthermal atmospheric argon plasma jet effects on Escherichia coli biomacromolecules.

    Science.gov (United States)

    Hosseinzadeh Colagar, Abasalt; Memariani, Hamed; Sohbatzadeh, Farshad; Valinataj Omran, Azadeh

    2013-12-01

    Nonthermal atmospheric plasma jet, a promising technology based on ionized gas at low temperatures, can be applied for disinfection of contaminated surfaces. In this study, Escherichia coli cells and their macromolecules were exposed to the nonthermal atmospheric argon plasma jet for different time durations. Total protein, genomic DNA, and malondialdehyde (MDA) levels of E. coli were assessed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and silver staining; agarose gel electrophoresis; and measurement of absorbance at 534 nm, respectively. After exposure, the spectroscopic results of liquid samples indicated that the survival reduction of E. coli can reach to 100 % in an exposure time of 600 s. Moreover, inactivation zones of E. coli, DNA degradation, and MDA levels were significantly increased. Additionally, banding patterns of total protein were changed and amino acid concentrations increased following ninhydrin test. The experimental results suggest that the nonthermal plasma could serve as an effective instrument for both sterilizing E. coli and degrading macromolecules from the surface of the objects being sterilized.

  11. Diagnostics of an AC driven atmospheric pressure non-thermal plasma jet and its use for radially directed jet array

    Science.gov (United States)

    Zhu, W.; Wang, R.

    2017-08-01

    An alternating current atmospheric pressure plasma jet is generated with noble gas or noble gas/oxygen admixture as working gas. A "core plasma filament" is observed at the center of the dielectric tube and extends to the plasma jet at higher peak-to-peak voltages. This type of plasma jet is believed to be of the same nature with the reported plasma bullet driven by pulsed DC power sources. Double current probes are used to assess the speed of the plasma bullet and show that the speed is around 104-105 m/s. The time dependence of the downstream bullet speed is attributed to the gas heating and in turn the increase of the reduced electric field E/N. Optical emission spectra show the dependence of helium and oxygen emission intensities on the concentration of oxygen additive in the carrier gas, with peak values found at 0.5% O2. Multiple radial jets are realized on dielectric tubes of different sizes. As a case study, one of these multi-jet devices is used to treat B. aureus on the inner surface of a plastic beaker and is shown to be more effective than a single jet.

  12. Synthetic Diagnostics Of The JET System Of The JET-2 Unmanned Drone

    Directory of Open Access Journals (Sweden)

    Sabak Ryszard

    2014-12-01

    Full Text Available In recent years, , newer and newer designs of unmanned air vehicles have been appeared and in a spread and spread area. That is why, their service and in particular their diagnostics should be carried out both before and in each flight. In this paper, a description of both unmanned air vehicle JET-2 and its units and control system are presented. The paper includes also description of signals which are transmitted in a real time from the dron to the flight control station. These signals enable to state whether the vehicle works in a correct way. An interactive diagnostics model is presented as two united equations of state which are based on an observation that the usable value of the UAV resulting from its working standards, depends on its technical condition and what is more, technical condition depends on its working condition (intensity of usage. It should be stated that technical conditions are an environment for working conditions and working conditions are an environments for technical conditions. Presented model gives a comprehensive information about technical and working capability of a vehicle. It enables to plan next flights taking into account their currant potential and capability.

  13. Exploration of Plasma Jets Approach to High Energy Density Physics. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chiping [Massachusetts Institute of Technology

    2013-08-26

    High-energy-density laboratory plasma (HEDLP) physics is an emerging, important area of research in plasma physics, nuclear physics, astrophysics, and particle acceleration. While the HEDLP regime occurs at extreme conditions which are often found naturally in space but not on the earth, it may be accessible by colliding high intensity plasmas such as high-energy-density plasma jets, plasmoids or compact toroids from plasma guns. The physics of plasma jets is investigated in the context of high energy density laboratory plasma research. This report summarizes results of theoretical and computational investigation of a plasma jet undergoing adiabatic compression and adiabatic expansion. A root-mean-squared (rms) envelope theory of plasma jets is developed. Comparison between theory and experiment is made. Good agreement between theory and experiment is found.

  14. Investigation of Synthetic Jets Efficiency to Control Cavity Flotation with Subsonic External Flow by High-Resolution RANS / ILES Method

    Directory of Open Access Journals (Sweden)

    D. A. Lyubimov

    2015-01-01

    Full Text Available Cavities often found in airplanes: a niche for the landing gear, various weapons, etc. Reducing fluctuations of pressure and temperature in the cavity is a relevant practical problem. The article presents simulation results of external subsonic flow around the cavity (M = 0.85, T = 300K. . Calculations were performed using the high-resolution RANS/ILES (Reynolds Averaged Navier-Stokes - RANS, Implicit Large Eddy Simulation - ILES method. To control flow the authors propose to use synthetic jets. Synthetic jets are produced by periodic ejection and suction of fluid from a slot induced by the movement of a diaphragm (generator of synthetic jets inside a cavity. They are compact and efficient and do not require a special working body and the ways for its supply. Instead of calculating the flow in the synthetic jet generator was used the modified boundary condition on the wall where the output slots was positioned. Under consideration there were two variants of slots for synthetic jets output: in front of the cavity and inside the cavity on the front wall. The frequency and amplitude values of the synthetic jet specified a mode of each jet. For a jet inside the cavity two modes have been reviewed, namely: 100 Hz and 50m/s, 200Hz and 50m/s. For jet in front of the cavity three modes have been reviewed, specifically: 20Hz and 20m/s, 100Hz and 50m/s, 200Hz and 50m/s. Analysis of calculation results showed that for all modes under examination, the synthetic jets reduced fluctuation of static pressure and temperature on the bottom and back walls of the cavity. The mode with parameters 200Hz, 50 m/s and synthetic jet located in front of the cavity was the most efficient. Furthermore, we compared the results of calculations for two-and three-dimensional cavities, which have the same length and depth. Research has shown that the simplified quasi-two-dimensional calculations cannot be used to evaluate the pressure and temperature fluctuations. This is due to

  15. Large-scale jets in the magnetosheath and plasma penetration across the magnetopause: THEMIS observations

    CERN Document Server

    Dmitriev, A V

    2015-01-01

    THEMIS multi-point observation of the plasma and magnetic fields, conducted simultaneously in the dayside magnetosheath and magnetosphere, were used to collect 646 large-scale magnetosheath plasma jets interacting with the magnetopause. The jets were identified as dense and fast streams of the magnetosheath plasma whose energy density is higher than that of the upstream solar wind. The jet interaction with the magnetopause was revealed from sudden inward motion of the magnetopause and an enhancement in the geomagnetic field. The penetration was determined as appearance of the magnetosheath plasma against the background of the hot magnetospheric particle population. We found that almost 60% of the jets penetrated through the magnetopause. Vast majority of the penetrating jets was characterized by high velocities V > 220 km/s and kinetic bk > 1 that corresponded to a combination of finite Larmor radius effect with a mechanisms of impulsive penetration. The average plasma flux in the penetrating jets was found t...

  16. Structural analysis of converging jets in a triple torch plasma system

    CERN Document Server

    Ramachandran, K

    2003-01-01

    A three-dimensional numerical model is developed to clarify the structure of the converging jets in a triple torch plasma system. Three individual argon plasma jets, issued into atmospheric argon, are mixed with given angle of convergence and form a converged plasma jet. Predicted results show that thermo-fluid fields of the converging plasma jets are symmetric with three symmetric sections at an interval 120 deg. Symmetry and uniformity of thermo-fluid fields increase with decreasing angle of convergence. Temperature field is more sensitive to angle of convergence than the velocity field. Symmetry of thermo-fluid fields is improved in downstream direction. A dip in the velocity fields corresponds to poor mixing and diffusion of velocity fields of three individual plasma jets. Central gas injection decreases converging jets temperature significantly.

  17. Modeling of plasma jet production from rail and coaxial guns for imploding plasma liner formation*

    Science.gov (United States)

    Mason, R. J.; Faehl, R. J.; Kirikpatrick, R. C.; Witherspoon, D.; Cassibry, J.

    2010-11-01

    We study the generation of plasma jets for forming imploding plasma liners using an enhanced version of the ePLAS implicit/hybrid model.^1 Typically, the jets are partially ionized D or Ar gases, in initial 3-10 cm long slugs at 10^16-10^18 electron/cm^3, accelerated for microseconds along 15-30 cm rail or coaxial guns with a 1 cm inter-electrode gap and driven by magnetic fields of a few Tesla. We re-examine the B-field penetration mechanisms that can be active in such wall-connected plasmas,^2 including erosion and EMHD influences, which can subsequently impact plasma liner formation and implosion. For the background and emitted plasma components we discuss optimized PIC and fluid modeling techniques, and the use of implicit fields and hybridized electrons to speed simulation. The plasmas are relatively cold (˜3 eV), so results with fixed atomic Z are compared to those from a simple analytic EOS, and allowing radiative heat loss from the plasma. The use of PIC ions is explored to extract large mean-free-path kinetic effects. 1. R. J. Mason and C. Cranfill, IEEE Trans. Plasma Sci. PS-14, 45 (1986) 2. R. Mason, et al., Phys. Fluids B, 5, 1115 (1993). [4pt] *Research supported in part by USDOE Grant DE-SC0004207.

  18. Plasma-Jet Forming of Sheet Metal Shapes

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Plasma-jet forming is a newly proposed flexible sheet metal forming process. A non-transferred arc plasma torch is used as a controllable heat source to produce internal stress in sheet metals, causing plastic deformation without the necessity of hard tooling. This method has potential for rapid prototyping of sheet metal parts by reducing development costs and lead times. A robotic system has been used to perform simple linear bends in several different alloys. In order to develop a controllable process and to improve the forming accuracy, the effects of various process parameters on the obtained shape changes and on the resulting structure and properties have been studied. The overall goal is to understand the roles of the forming parameters and their inter-relationship in optimizing the forming procedure-a high forming speed without damage to the material structure or properties.

  19. Solitary and freak waves in superthermal plasma with ion jet

    Science.gov (United States)

    Abdelsalam, U. M.; Abdelsalam

    2013-06-01

    The nonlinear solitary and freak waves in a plasma composed of positive and negative ions, superthermal electrons, ion beam, and stationary dust particles have been investigated. The reductive perturbation method is used to obtain the Korteweg-de Vries (KdV) equation describing the system. The latter admits solitary wave solution, while the dynamics of the modulationally unstable wavepackets described by the KdV equation gives rise to the formation of freak/rogue excitation described by the nonlinear Schrödinger equation. In order to show that the characteristics of solitary and freak waves are influenced by plasma parameters, relevant numerical analysis of appropriate nonlinear solutions are presented. The results from this work predict nonlinear excitations that may associate with ion jet and superthermal electrons in Herbig-Haro objects.

  20. New insights on the propagation of pulsed atmospheric plasma streams: From single jet to multi jet arrays

    Energy Technology Data Exchange (ETDEWEB)

    Robert, E.; Darny, T.; Dozias, S.; Iseni, S.; Pouvesle, J. M. [GREMI, UMR 7344, CNRS/Université d' Orléans, BP 6744, 45067 Orléans Cedex 2 (France)

    2015-12-15

    Atmospheric pressure plasma propagation inside long dielectric tubes is analyzed for the first time through nonintrusive and nonperturbative time resolved bi-directional electric field (EF) measurements. This study unveils that plasma propagation occurs in a region where longitudinal EF exists ahead the ionization front position usually revealed from plasma emission with ICCD measurement. The ionization front propagation induces the sudden rise of a radial EF component. Both of these EF components have an amplitude of several kV/cm for helium or neon plasmas and are preserved almost constant along a few tens of cm inside a capillary. All these experimental measurements are in excellent agreement with previous model calculations. The key roles of the voltage pulse polarity and of the target nature on the helium flow patterns when plasma jet is emerging in ambient air are documented from Schlieren visualization. The second part of this work is then dedicated to the development of multi jet systems, using two different setups, based on a single plasma source. Plasma splitting in dielectric tubes drilled with sub millimetric orifices, but also plasma transfer across metallic tubes equipped with such orifices are reported and analyzed from ICCD imaging and time resolved EF measurements. This allows for the design and the feasibility validation of plasma jet arrays but also emphasizes the necessity to account for voltage pulse polarity, target potential status, consecutive helium flow modulation, and electrostatic influence between the produced secondary jets.

  1. Helium atmospheric pressure plasma jets touching dielectric and metal surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Norberg, Seth A., E-mail: norbergs@umich.edu; Johnsen, Eric, E-mail: ejohnsen@umich.edu [Department of Mechanical Engineering, University of Michigan, 2350 Hayward Street, Ann Arbor, Michigan 48109-2125 (United States); Kushner, Mark J., E-mail: mjkush@umich.edu [Department of Electrical Engineering and Computer Science, University of Michigan, 1301 Beal Avenue, Ann Arbor, Michigan 48109-2122 (United States)

    2015-07-07

    Atmospheric pressure plasma jets (APPJs) are being investigated in the context plasma medicine and biotechnology applications, and surface functionalization. The composition of the surface being treated ranges from plastics, liquids, and biological tissue, to metals. The dielectric constant of these materials ranges from as low as 1.5 for plastics to near 80 for liquids, and essentially infinite for metals. The electrical properties of the surface are not independent variables as the permittivity of the material being treated has an effect on the dynamics of the incident APPJ. In this paper, results are discussed from a computational investigation of the interaction of an APPJ incident onto materials of varying permittivity, and their impact on the discharge dynamics of the plasma jet. The computer model used in this investigation solves Poisson's equation, transport equations for charged and neutral species, the electron energy equation, and the Navier-Stokes equations for the neutral gas flow. The APPJ is sustained in He/O{sub 2} = 99.8/0.2 flowing into humid air, and is directed onto dielectric surfaces in contact with ground with dielectric constants ranging from 2 to 80, and a grounded metal surface. Low values of relative permittivity encourage propagation of the electric field into the treated material and formation and propagation of a surface ionization wave. High values of relative permittivity promote the restrike of the ionization wave and the formation of a conduction channel between the plasma discharge and the treated surface. The distribution of space charge surrounding the APPJ is discussed.

  2. Atmospheric Pressure Plasma Jet as a Dry Alternative to Inkjet Printing in Flexible Electronics

    Science.gov (United States)

    Gandhiraman, Ram Prasad; Lopez, Arlene; Koehne, Jessica; Meyyappan, M.

    2016-01-01

    We have developed an atmospheric pressure plasma jet printing system that works at room temperature to 50 deg C unlike conventional aerosol assisted techniques which require a high temperature sintering step to obtain desired thin films. Multiple jets can be configured to increase throughput or to deposit multiple materials, and the jet(s) can be moved across large areas using a x-y stage. The plasma jet has been used to deposit carbon nanotubes, graphene, silver nanowires, copper nanoparticles and other materials on substrates such as paper, cotton, plastic and thin metal foils.

  3. Atmospheric Pressure Plasma Jet for Chem/Bio Warfare Decontamination

    Science.gov (United States)

    Herrmann, Hans W.; Henins, Ivars; Park, Jaeyoung; Selwyn, Gary S.

    1999-11-01

    Atmospheric Pressure Plasma Jet (APPJ) technology may provide a much needed method of CBW decontamination which, unlike traditional decon methods, is dry and nondestructive to sensitive equipment and materials. The APPJ discharge uses a high-flow feedgas consisting primarily of an inert carrier gas, such as He, and a small amount of a reactive additive, such as O2, which flows between capacitively-coupled electrodes powered at 13.56 MHz. The plasma generates highly reactive metastable and atomic species of oxygen which are then directed onto a contaminated surface. The reactive effluent of the APPJ has been shown to effectively neutralize VX nerve agent as well as simulants for anthrax and mustard blister agent. Research efforts are now being directed towards reducing He consumption and increasing the allowable stand-off distance. Recent results demonstrate that by replacing the O2 reactive additive with CO2, ozone formation is greatly reduced. This has the result of extending the lifetime of atomic oxygen by an order of magnitude or more. A recirculating APP Decon Chamber which combines heat, vacuum, forced convection and reactivity is currently being developed for enhanced decontamination of sensitive equipment. Several techniques are also being evaluated for use in an APP Decon Jet for decontamination of items which cannot be placed inside a chamber.

  4. Basic characteristics of an atmospheric pressure rf generated plasma jet

    Institute of Scientific and Technical Information of China (English)

    Wang Shou-Guo; Li Hai-Jiang; Ye Tian-Chun; Zhao Ling-Li

    2004-01-01

    A plasma jet has been developed which operates using radio frequency (rf) power and produces a stable homogeneous discharge at atmospheric pressure. Its discharge characteristics, especially the dependence of stable discharge operating range on the feed gas, were studied, and the electric parameters such as RMS current, RMS voltage and reflected power were obtained with different gas flows. These studies indicate that there is an optimum range of operation of the plasma jet for a filling with a gas mixture of He and O2. Two "failure" modes of the discharge are identified.One is a filamentary arc when the input power is raised above a critical level, another is that the discharge disappears gradually as the addition of O2 approaches 3.2%. Possible explanations for the two failure modes have been given. The current and voltage waveform measurements show that there is a clear phase shift between normal and failure modes.In addition, Ⅰ-Ⅴ curves as a function of pure helium and for 1% addition of oxygen have been studied.

  5. RF atmospheric plasma jet surface treatment of paper

    Science.gov (United States)

    Pawlat, Joanna; Terebun, Piotr; Kwiatkowski, Michał; Diatczyk, Jaroslaw

    2016-09-01

    A radio frequency RF atmospheric pressure plasma jet was used to enhance the wettability of cellulose-based paper of 90 g m-2 and 160 g m-2 grammage as a perspective platform for antibiotic sensitivity tests. Helium and argon were the carrier gases for oxygen and nitrogen; pure water and rapeseed oil were used for goniometric tests. The influence of the flow rate and gas type, the power of the discharge, and distance from the nozzle was examined. The surface structure was observed using an optical microscope. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectra were investigated in order to determine whether cellulose degradation processes occurred. The RF plasma jet allowed us to decrease the surface contact angle without drastic changes in other features of the tested material. Experiments confirmed the significant influence of the distance between the treated sample and reactor nozzle, especially for treatment times longer than 15 s due to the greater concentration of reactive species at the surface of the sample, which decreases with distance—and their accumulation effect with time. The increase of discharge power plays an important role in decreasing the surface contact angle for times longer than 10 s. Higher power had a positive effect on the amount of generated active particles and facilitated the ignition of discharge. However, a too high value can cause a rise in temperature of the material and heat-caused damage.

  6. A Laboratory Plasma Experiment for Studying Magnetic Dynamics of Accretion Discs and Jets

    OpenAIRE

    Hsu, S. C.; Bellan, P. M.

    2002-01-01

    This work describes a laboratory plasma experiment and initial results which should give insight into the magnetic dynamics of accretion discs and jets. A high-speed multiple-frame CCD camera reveals images of the formation and helical instability of a collimated plasma, similar to MHD models of disc jets, and also plasma detachment associated with spheromak formation, which may have relevance to disc winds and flares. The plasmas are produced by a planar magnetized coaxial gun. The resulting...

  7. Interplay of discharge and gas flow in atmospheric pressure plasma jets

    Science.gov (United States)

    Jiang, Nan; Yang, JingLong; He, Feng; Cao, Zexian

    2011-05-01

    Interplay of discharge and gas flow in the atmospheric pressure plasma jets generated with three different discharge modes [N. Jiang, A. L. Ji, and Z. X. Cao, J. Appl. Phys. 106, 013308 (2009); N. Jiang, A. L. Ji, and Z. X. Cao, J. Appl. Phys. 108, 033302 (2010)] has been investigated by simultaneous photographing of both plasma plumes and gas flows in the ambient, with the former being visualized by using an optical schlieren system. Gas flow gains a forward momentum from discharge except for the case of overflow jets at smaller applied voltages. Larger applied voltage implies an elongated plasma jet only for single-electrode mode; for dielectric barrier discharge jet the plume length maximizes at a properly applied voltage. These findings can help understand the underlying processes, and are useful particularly for the economic operation of tiny helium plasma jets and jet arrays.

  8. Overview of modelling activities for Plasma Control Upgrade in JET

    Energy Technology Data Exchange (ETDEWEB)

    Albanese, R., E-mail: raffaele.albanese@unina.it [Consorzio CREATE, Euratom-ENEA Association, DIEL, Univ. Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Ambrosino, G.; Ariola, M.; Artaserse, G.; Bellizio, T. [Consorzio CREATE, Euratom-ENEA Association, DIEL, Univ. Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Coccorese, V. [Consorzio CREATE, Euratom-ENEA Association, DIEL, Univ. Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); EFDA Close Support Unit, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Crisanti, F. [ENEA Fus, EURATOM Assoc, 00040 Frascati (Italy); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); De Tommasi, G.; Fresa, R. [Consorzio CREATE, Euratom-ENEA Association, DIEL, Univ. Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Lomas, P.J. [CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Mattei, M.; Maviglia, F. [Consorzio CREATE, Euratom-ENEA Association, DIEL, Univ. Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Neto, A. [Associacao Euratom-IST, Instituto de Plasmas e Fusao Nuclear, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Piccolo, F. [CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Pironti, A. [Consorzio CREATE, Euratom-ENEA Association, DIEL, Univ. Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); JET-EFDA, Culham Science Centre, OX14 3DB Abingdon (United Kingdom)

    2011-10-15

    The JET enhancement project Plasma Control Upgrade (PCU) aimed at increasing the capabilities of the plasma vertical stabilization (VS) system. One of the activities of this project was devoted to the development of simple but sufficiently accurate models of the VS system so as to address the main design choices, use the simulation tools as reliable test-beds, and provide an adequate support to the engineering design and commissioning of the new Enhanced Radial Field Amplifier (ERFA). This paper illustrates some of the main achievements of the modelling activity, which gave rise to a closed loop model of the VS system, including plasma, PF coils and passive structures. In particular the paper deals with the selection of the set of turns to be used in the control coils and with the estimation of the eddy current effects on the VS system. The latter analysis addressed an upgrade of the converter units of ERFA, successfully implemented during its commissioning on plasma in August 2009.

  9. Use of Atmospheric-Pressure Plasma Jet for Polymer Surface Modification: An Overview

    Energy Technology Data Exchange (ETDEWEB)

    Kuettner, Lindsey A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-16

    Atmospheric-pressure plasma jets (APPJs) are playing an increasingly important role in materials processing procedures. Plasma treatment is a useful tool to modify surface properties of materials, especially polymers. Plasma reacts with polymer surfaces in numerous ways thus the type of process gas and plasma conditions must be explored for chosen substrates and materials to maximize desired properties. This report discusses plasma treatments and looks further into atmospheric-pressure plasma jets and the effects of gases and plasma conditions. Following the short literature review, a general overview of the future work and research at Los Alamos National Laboratory (LANL) is discussed.

  10. MTF Driven by Plasma Liner Dynamically Formed by the Merging of Plasma Jets: An Overview

    Science.gov (United States)

    Thio, Y. C. Francis; Eskridge, Richard; Martin, Adam; Smith, James; Lee, Michael; Rodgers, Stephen L. (Technical Monitor)

    2001-01-01

    One approach for standoff delivery of the momentum flux for compressing the target in MTF consists of using a spherical array of plasma jets to form a spherical plasma shell imploding towards the center of a magnetized plasma, a compact toroid (Figure 1). A 3-year experiment (PLX-1) to explore the physics of forming a 2-D plasma liner (shell) by merging plasma jets is described. An overview showing how this 3-year project (PLX-1) fits into the program plan at the national and international level for realizing MTF for energy and propulsion is discussed. Assuming that there will be a parallel program in demonstrating and establishing the underlying physics principles of MTF using whatever liner is appropriate (e.g. a solid liner) with a goal of demonstrating breakeven by 2010, the current research effort at NASA MSFC attempts to complement such a program by addressing the issues of practical embodiment of MTF for propulsion. Successful conclusion of PLX-1 will be followed by a Physics Feasibility Experiment (PLX-2) for the Plasma Liner Driven MTF.

  11. MULTIPLE PLASMA EJECTIONS AND INTERMITTENT NATURE OF MAGNETIC RECONNECTION IN SOLAR CHROMOSPHERIC ANEMONE JETS

    Energy Technology Data Exchange (ETDEWEB)

    Singh, K. A. P.; Nishida, K.; Shibata, K. [Kwasan and Hida Observatories, Graduate School of Science, Kyoto University, Yamashina, Kyoto 607-8471 (Japan); Isobe, H. [Unit of Synergetic Study for Space, Kyoto University, Yamashina, Kyoto 607-8471 (Japan); Nishizuka, N., E-mail: singh@kwasan.kyoto-u.ac.jp, E-mail: nishida@kwasan.kyoto-u.ac.jp, E-mail: shibata@kwasan.kyoto-u.ac.jp, E-mail: isobe@kwasan.kyoto-u.ac.jp, E-mail: nishizuka.naoto@jaxa.jp [Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, 3-1-1 Yoshinodai, Chuo-ku, Sagamihara-shi, Kanagawa 229-8510 (Japan)

    2012-11-01

    The recent discovery of chromospheric anemone jets with the Solar Optical Telescope (SOT) on board Hinode has shown an indirect evidence of magnetic reconnection in the solar chromosphere. However, the basic nature of magnetic reconnection in chromosphere is still unclear. We studied nine chromospheric anemone jets from SOT/Hinode using Ca II H filtergrams, and we found multiple bright, plasma ejections along the jets. In most cases, the major intensity enhancements (larger than 30% relative to the background intensity) of the loop correspond to the timing of the plasma ejections. The typical lifetime and size of the plasma ejecta are about 20-60 s and 0.3-1.5 Mm, respectively. The height-time plot of jet shows many sub-structures (or individual jets) and the typical lifetime of the individual jet is about one to five minutes. Before the onset of the jet activity, a loop appears in Ca II H and gradually increases in size, and after few minutes several jets are launched from the loop. Once the jet activity starts and several individual jets are launched, the loop starts shrinking with a speed of {approx}4 km s{sup -1}. In some events, a downward moving blob with a speed of {approx}35 km s{sup -1} was observed, associated with the upward moving plasma along one of the legs of the loop hosting the jets. The upward moving plasma gradually developed into jets. Multiple plasma ejections in chromospheric anemone jet show the strongly time-dependent as well as intermittent nature of magnetic reconnection in the solar chromosphere.

  12. A model for straight and helical solar jets. II. Parametric study of the plasma beta

    Science.gov (United States)

    Pariat, E.; Dalmasse, K.; DeVore, C. R.; Antiochos, S. K.; Karpen, J. T.

    2016-11-01

    Context. Jets are dynamic, impulsive, well-collimated plasma events that develop at many different scales and in different layers of the solar atmosphere. Aims: Jets are believed to be induced by magnetic reconnection, a process central to many astrophysical phenomena. Within the solar atmosphere, jet-like events develop in many different environments, e.g., in the vicinity of active regions, as well as in coronal holes, and at various scales, from small photospheric spicules to large coronal jets. In all these events, signatures of helical structure and/or twisting/rotating motions are regularly observed. We aim to establish that a single model can generally reproduce the observed properties of these jet-like events. Methods: Using our state-of-the-art numerical solver ARMS, we present a parametric study of a numerical tridimensional magnetohydrodynamic (MHD) model of solar jet-like events. Within the MHD paradigm, we study the impact of varying the atmospheric plasma β on the generation and properties of solar-like jets. Results: The parametric study validates our model of jets for plasma β ranging from 10-3 to 1, typical of the different layers and magnetic environments of the solar atmosphere. Our model of jets can robustly explain the generation of helical solar jet-like events at various β ≤ 1. We introduces the new result that the plasma β modifies the morphology of the helical jet, explaining the different observed shapes of jets at different scales and in different layers of the solar atmosphere. Conclusions: Our results enable us to understand the energisation, triggering, and driving processes of jet-like events. Our model enables us to make predictions of the impulsiveness and energetics of jets as determined by the surrounding environment, as well as the morphological properties of the resulting jets.

  13. Development of Detailed and Reduced Kinetics Mechanisms for Surrogates of Petroleum-Derived and Synthetic Jet Fuels

    Science.gov (United States)

    2014-12-04

    nitrogen are introduced into an opposed jet annular mixing nozzle at the inlet to the quartz reactor tube. A water-cooled, borosilicate glass-lined...where it is rapidly mixed with synthetic air in the opposed jet annular mixing nozzle. Further dilution with nitrogen is used to limit temperature...the 700 K temperature sample point. Figure 3 presents the key linear alkenes measured during n-PCH oxidation. In addition to ethene, propene, and

  14. Ion-viscosity effects on plasma-liner formation and implosion via merging supersonic plasma jets

    Science.gov (United States)

    Schillo, Kevin; Cassibry, Jason; Samulyak, Roman; Shih, Wen; Hsu, Scott; PLX-Alpha Team

    2016-10-01

    The PLX- α project endeavors to study plasma-liner formation and implosion by merging a spherical array of plasma jets as a candidate standoff driver for MIF. Smoothed particle hydrodynamics is used to model the liner formation and implosion processes. SPH is a meshless Lagrangian method to simulate fluid flows by dividing a fluid into a set of particles and using a summation interpolant function to calculate the properties and gradients for each of these particles. Ion viscosity is anticipated to be an important mechanism for momentum transport during liner formation, implosion, and stagnation. To study this, ion viscosity was incorporated into the code. To provide confidence in the numerical output and to help identify the difference between numerical and physical diffusion, a series of test cases were performed, consisting of Couette flow, Gresho vortex, and a Taylor-Green vortex. An L2-norm analysis was performed to measure the error and convergence. Simulations of conical (6 jets) and 4 π (60 jets) liners with and without ion viscosity reveal potential effects of viscosity on ram pressure, Mach-number degradation, and evolution of liner perturbations during jet merging and liner implosion.

  15. Three-Dimensional Simulation of Plasma Jet and Particle Groups in Plasma Spraying

    Institute of Scientific and Technical Information of China (English)

    FAN Qun-bo; WANG Lu; WANG Fu-chi

    2008-01-01

    The temperature field, velocity field, as well as species distribution in three-dimensional space are successfully calculated by establishing three-dimensional geometry model and solving plasma jet-substrate interaction equations, optimized particle trajecory models, as well as particle-particle heat transfer equations in three-dimensionalal space. Under typical working conditions, the flying trajectories and distribution of ZrO2 ceramic particles and Ni metal particles are also simulated. Results show that, the plasma jet becomes wider near the substrate, and the stochastic trajectory model is preferable to simulate the turbulent diffusion effect of particles. In addition, Ni metal particles penetrate relatively more deeply than ZrO2 ceramic particles due to larger density.

  16. Magnetic Probe to Study Plasma Jets for Magneto-Inertial Fusion

    Energy Technology Data Exchange (ETDEWEB)

    Martens, Daniel [Los Alamos National Laboratory; Hsu, Scott C. [Los Alamos National Laboratory

    2012-08-16

    A probe has been constructed to measure the magnetic field of a plasma jet generated by a pulsed plasma rail-gun. The probe consists of two sets of three orthogonally-oriented commercial chip inductors to measure the three-dimensional magnetic field vector at two separate positions in order to give information about the magnetic field evolution within the jet. The strength and evolution of the magnetic field is one of many factors important in evaluating the use of supersonic plasma jets for forming imploding spherical plasma liners as a standoff driver for magneto-inertial fusion.

  17. Development of atmospheric pressure plasma needle jet for sterilization applications

    Science.gov (United States)

    Elfa, Rizan Rizon; Ahmad, Mohd Khairul; Soon, Chin Fhong; Sahdan, Mohd Zainizan; Lias, Jais; Wibowo, Kusnanto Mukti; Bakar, Ahmad Shuhaimi Abu; Arshad, Mohd Khairuddin Md; Hashim, Uda; Nayan, Nafarizal

    2017-09-01

    Inactivation of bacteria or sterilization has been a major issue in the medical field, especially regarding of human safety, whereby, in a huge scenario fatality can be caused by hazardous bacteria. Often, E-coli as gram-negative bacteria are selected as a key indicator of proper sterilization process as E-coli is tough and dormant bacteria. The technology in sterilization has moved on from chemical, wet and irradiation sterilization to a high promising device such as atmospheric pressure plasma needle jet (APPNJ). It has been reported that atmospheric pressure plasma has provided bundle of advantages over earlier sterilization process. The APPNJ is developed in our lab using high frequency and high voltage neon transformer power supply connected to copper needle and copper sheet electrodes. The gas discharge is Ar gas flowing at 40 L/min through a quartz glass tube. The E-coli bacteria are self-cultured from waste water and then treated with APPNJ. The treatment processes are run into two difference gaps between the plasma orifice and sample with various treatment times. Only 40s is required by direct treatment to achieve 100% killing of E-coli. On the other hand, indirect treatment has inactivated 50% of the E-coli in 40s. In this study, direct and indirect effect of APPNJ to the E-coli can be observed which can be utilized into sterilization of bio-compatible material applications.

  18. Power modulation in an atmospheric pressure plasma jet

    Science.gov (United States)

    Kelly, S.; Turner, M. M.

    2014-12-01

    Power modulation in an atmospheric pressure capacitively coupled radio frequency plasma jet is investigated by numerical modelling. The dynamics of successively pulsing the applied power on and off for a helium-oxygen (˜0.6%) plasma is investigated. The impact of power pulsing on reactive species generation and gas heating is discussed with control opportunities emphasized. Power modulation shows linear control for reactive species and heat flux delivery to a treatment surface above an initial phase of power growth. Power is found to be coupled primarily to the electrons with electron loss rates determining the interference between successive power modulation phases. Plasma decay in the power off phase is characterized by a large initial electron loss in the first 0.5 µs followed by ambipolar decay dominated by ions of opposite charge. Power modulation effects on gas heating show a larger range of temperature control when compared with convection cooling. Reactive oxygen species reaching a treatment surface are shown to typically vary over an order of magnitude for variation in the duty cycle.

  19. Experimental investigation of influence of Reynolds number on synthetic jet vortex rings impinging onto a solid wall

    Science.gov (United States)

    Xu, Yang; He, GuoSheng; Kulkarni, Varun; Wang, JinJun

    2017-01-01

    Time-resolved particle image velocimetry was employed to study the effect of Reynolds number ( Re sj) on synthetic jet vortex rings impinging onto a solid wall. Four Reynolds numbers ranging from 166 to 664 were investigated for comparison while other parameters were kept constant. It is found that the Reynolds number has a significant impact on the spatial evolution of near-wall vortical structures of the impinging synthetic jet. Velocity triple decomposition reveals that periodic Reynolds shear stresses produced by both impinging and secondary vortex rings agree well with a four-quadrant-type distribution rule, and the random velocity fluctuations are strengthened as Re sj increases. For radial wall jet, radial velocity profiles exhibit a self-similar behavior for all Re sj, and this self-similar profile gradually deviates from the laminar solution as Re sj is increased. In particular, the self-similar profile for low Re sj (166) coincides with the laminar solution indicating that periodic velocity fluctuations produced by vortex rings have little effect on the velocity profile of the laminar wall jet. This also provides evidence that the impinging synthetic jet is more effective in mixing than the continuous jet for the laminar flow. For the high Re sj, the mean skin friction coefficient has a slower decay rate after reaching peak, and the radial momentum flux has a higher value at locations far away from the impingement region, both of these can be attributed to the enhanced random fluctuations.

  20. Power efficiency of the active boundary layer control around the hump by a slotted synthetic jet generator

    Directory of Open Access Journals (Sweden)

    Pick Petr

    2015-01-01

    Full Text Available The present contribution summarizes the power efficiency of the active flow control of the boundary layer of air around a hump. The synthetic jet generator with a rectangular output part, i.e. a slot, is actuated using a modulated signal. The actuation of the synthetic jet is carried out by modulating the input voltage of acoustic transducers of the generator. This causes the decrease of the loss coefficient and the change of the mixing size area (e.g. wake. A comparison of three types of modulating signals and their influence on the loss coefficient is performed. The main advantages of modulated signal are then described.

  1. On the evolution of jet energy and opening angle in strongly coupled plasma

    Energy Technology Data Exchange (ETDEWEB)

    Chesler, Paul M. [Department of Physics, Harvard University,Cambridge MA 02138 (United States); Rajagopal, Krishna [Center for Theoretical Physics, MIT,Cambridge MA 02139 (United States)

    2016-05-17

    We calculate how the energy and the opening angle of jets in N=4 SYM theory evolve as they propagate through the strongly coupled plasma of that theory. We define the rate of energy loss dE{sub jet}/dx and the jet opening angle in a straightforward fashion directly in the gauge theory before calculating both holographically, in the dual gravitational description. In this way, we rederive the previously known result for dE{sub jet}/dx without the need to introduce a finite slab of plasma. We obtain a striking relationship between the initial opening angle of the jet, which is to say the opening angle that it would have had if it had found itself in vacuum instead of in plasma, and the thermalization distance of the jet. Via this relationship, we show that N=4 SYM jets with any initial energy that have the same initial opening angle and the same trajectory through the plasma experience the same fractional energy loss. We also provide an expansion that describes how the opening angle of the N=4 SYM jets increases slowly as they lose energy, over the fraction of their lifetime when their fractional energy loss is not yet large. We close by looking ahead toward potential qualitative lessons from our results for QCD jets produced in heavy collisions and propagating through quark-gluon plasma.

  2. Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis

    Directory of Open Access Journals (Sweden)

    Grzegorz Raniszewski

    2017-02-01

    Full Text Available One of the most common methods of carbon nanotubes (CNTs synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon–plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs. It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented.

  3. Sterilization of Staphylococcus Aureus by an Atmospheric Non-Thermal Plasma Jet

    Science.gov (United States)

    Liu, Xiaohu; Hong, Feng; Guo, Ying; Zhang, Jing; Shi, Jianjun

    2013-05-01

    An atmospheric non-thermal plasma jet was developed for sterilizing the Staphylococcus aureus (S. aureus). The plasma jet was generated by dielectric barrier discharge (DBD), which was characterized by electrical and optical diagnostics. The survival curves of the bacteria showed that the plasma jet could effectively inactivate 106 cells of S. aureus within 120 seconds and the sterilizing efficiency depended critically on the discharge parameter of the applied voltage. It was further confirmed by scanning electron microscopy (SEM) that the cell morphology was seriously damaged by the plasma treatment. The plasma sterilization mechanism of S. aureus was attributed to the active species of OH, N2+ and O, which were generated abundantly in the plasma jet and characterized by OES. Our findings suggest a convenient and low-cost way for sterilization and inactivation of bacteria.

  4. Effective dose delivery in atmospheric pressure plasma jets for plasma medicine: a model predictive control approach

    Science.gov (United States)

    Gidon, Dogan; Graves, David B.; Mesbah, Ali

    2017-08-01

    Atmospheric pressure plasma jets (APPJs) have been identified as a promising tool for plasma medicine. This paper aims to demonstrate the importance of using model-based feedback control strategies for safe, reproducible, and therapeutically effective application of APPJs for dose delivery to a target substrate. Key challenges in model-based control of APPJs arise from: (i) the multivariable, nonlinear nature of system dynamics, (ii) the need for constraining the system operation within an operating region that ensures safe plasma treatment, and (iii) the cumulative, nondecreasing nature of dose metrics. To systematically address these challenges, we propose a model predictive control (MPC) strategy for real-time feedback control of a radio-frequency APPJ in argon. To this end, a lumped-parameter, physics-based model is developed for describing the jet dynamics. Cumulative dose metrics are defined for quantifying the thermal and nonthermal energy effects of the plasma on substrate. The closed-loop performance of the MPC strategy is compared to that of a basic proportional-integral control system. Simulation results indicate that the MPC stategy provides a versatile framework for dose delivery in the presence of disturbances, while the safety and practical constraints of the APPJ operation can be systematically handled. Model-based feedback control strategies can lead to unprecedented opportunities for effective dose delivery in plasma medicine.

  5. Effects of real viscosity on plasma liner formation and implosion from supersonic plasma jets

    Science.gov (United States)

    Schillo, Kevin; Cassibry, Jason; Hsu, Scott; PLX-Alpha Team

    2015-11-01

    The PLX- α project endeavors to study plasma liner formation and implosion by merging of a spherical array of plasma jets as a candidate standoff driver for magneto-inertial fusion (MIF). Smoothed particle hydrodynamics (SPH) is being used to model the liner formation and implosion processes. SPH is a meshless Lagrangian method to simulate fluid flows by dividing a fluid into a set of particles and using a summation interpolant function to calculate the properties and gradients for each of these particles. The SPH code was used to simulate test cases in which the number of plasma guns and initial conditions for the plasma were varied. Linear stabilizations were observed, but the possibility exists that this stabilization was due to the implementation of artificial viscosity in the code. A real viscosity model was added to our SPHC model using the Braginskii ion viscosity. Preliminary results for test cases that incorporate real viscosity are presented.

  6. Correlation between helium atmospheric pressure plasma jet (APPJ) variables and plasma induced DNA damage

    Science.gov (United States)

    Adhikari, Ek R.; Ptasinska, Sylwia

    2016-09-01

    A helium atmospheric pressure plasma jet (APPJ) source with a dielectric capillary and two tubular electrodes was used to induce damage in aqueous plasmid DNA. The fraction of different types of DNA damage (i.e., intact or undamaged, double strand breaks (DSBs), and single strand breaks (SSBs)) that occurred as the result of plasma irradiation was quantified through analysis of agarose gel electrophoresis images. The total DNA damage increased with an increase in both flow rate and duration of irradiation, but decreased with an increase in distance between the APPJ and sample. The average power of the plasma was calculated and the length of APPJ was measured for various flow rates and voltages applied. The possible effects of plasma power and reactive species on DNA damage are discussed.

  7. Modeling the Compression of Merged Compact Toroids by Multiple Plasma Jets

    Science.gov (United States)

    Thio, Y. C. Francis; Knapp, Charles E.; Kirkpatrick, Ron; Rodgers, Stephen L. (Technical Monitor)

    2000-01-01

    A fusion propulsion scheme has been proposed that makes use of the merging of a spherical distribution of plasma jets to dynamically form a gaseous liner. The gaseous liner is used to implode a magnetized target to produce the fusion reaction in a standoff manner. In this paper, the merging of the plasma jets to form the gaseous liner is investigated numerically. The Los Alamos SPHINX code, based on the smoothed particle hydrodynamics method is used to model the interaction of the jets. 2-D and 3-D simulations have been performed to study the characteristics of the resulting flow when these jets collide. The results show that the jets merge to form a plasma liner that converge radially which may be used to compress the central plasma to fusion conditions. Details of the computational model and the SPH numerical methods will be presented together with the numerical results.

  8. Computational study of flow dynamics from a dc arc plasma jet

    CERN Document Server

    Trelles, Juan Pablo

    2013-01-01

    Plasma jets produced by direct-current (DC) non-transferred arc plasma torches, at the core of technologies ranging from spray coating to pyrolysis, present intricate dynamics due to the coupled interaction of fluid flow, thermal, and electromagnetic phenomena. The flow dynamics from an arc discharge plasma jet are investigated using time-dependent three-dimensional simulations encompassing the dynamics of the arc inside the torch, the evolution of the jet through the discharge environment, and the subsequent impingement of the jet over a flat substrate. The plasma is described by a chemical equilibrium and thermodynamic nonequilibrium (two-temperature) model. The numerical formulation of the physical model is based on a monolithic and fully-coupled treatment of the fluid and electromagnetic equations using a Variational Multiscale Finite Element Method. Simulation results uncover distinct aspects of the flow dynamics, including the jet forcing due to the movement of the electric arc, the prevalence of deviat...

  9. Separation control using synthetic vortex generator jets in axial compressor cascade

    Institute of Scientific and Technical Information of China (English)

    Xinqian Zheng; Sheng Zhou; Anping Hou; Zhengli Jiang; Daijun Ling

    2006-01-01

    An experimental investigation conducted in a high-speed plane cascade wind tunnel demonstrates that unsteady flow control by using synthetic(zero mass flux)vortex generator jets can effectively improve the aerodynamic performances and reduce(or eliminate) flow separation in axial compressor cascade.The Mach number of the incoming flow is up to 0.7 and most tested cases are at Ma=0.3.The incidence is 10° at which the boundary layer is separated from 70% of the chord length.The roles of excitation frequency,amplitude,location and pitch angle are investigated.Preliminary results show that the excitation amplitude plays a very important role.The optimal excitation location is just upstream of the separation point,and the optimal pitch angle is 35°.The maximum relative reduction of loss coefficient is 22.8%.

  10. Maximization of integral outlet quantities of an axisymmetric synthetic jet actuator based on a loudspeaker

    Directory of Open Access Journals (Sweden)

    Kordík J.

    2016-01-01

    Full Text Available The goal of this paper is to find an optimal nozzle size of an axisymmetric synthetic jet actuator based on a loudspeaker. The desirable maximized output quantities are: volumetric flow, momentum flux, and kinetic energy flux. To evaluate these quantities velocity profiles were measured using a hot-wire probe at the actuator nozzle exit. Six different nozzle diameters and three supplied real power levels were tested to find the maxima of the quantities. The actuator operated always at resonance during experiments. It was found out that the momentum flux and the kinetic energy flux reach distinguishable local maxima at particular diameters of the nozzle. Besides, the maxima of the particular quantities do not coincide and the best nozzle size slightly increases with the supplied real power to the actuator.

  11. Design & Development of a High Mass Flow Piston Synthetic Jet Actuator

    Science.gov (United States)

    Ashraf, Hamad Muhammad; Murugan Illikkal, Karthika; D'souza, Francis; Alsayed Mahmood, Mohamed; Mahmud Mostafa, Suhail; Kim, Young Hwan

    2015-05-01

    The idea of having a device that is capable of working in a systematic process allowing control of the boundary layer by means of operated on high-frequency, small-scale, and low energy actuators has caught the interest of the aerodynamicist community. With an eye on the available data and potential flow control advantages, our research team set out to manufacture a compact SJA (Synthetic Jet Actuator) of its own, which would be capable of being installed inside an airfoil. It consists of components such as a single piston cylinder, with variable exit geometry along with the control system that has an electrical actuator which can be regulated in order for it to be capable of producing various operating frequencies. This paper consists of a study into the design of a single piston device SJA and will present all significant data both theoretical and computational regarding its design and performance.

  12. Design & Development of a High Mass Flow Piston Synthetic Jet Actuator

    Directory of Open Access Journals (Sweden)

    Ashraf Hamad Muhammad

    2015-01-01

    Full Text Available The idea of having a device that is capable of working in a systematic process allowing control of the boundary layer by means of operated on high-frequency, small-scale, and low energy actuators has caught the interest of the aerodynamicist community. With an eye on the available data and potential flow control advantages, our research team set out to manufacture a compact SJA (Synthetic Jet Actuator of its own, which would be capable of being installed inside an airfoil. It consists of components such as a single piston cylinder, with variable exit geometry along with the control system that has an electrical actuator which can be regulated in order for it to be capable of producing various operating frequencies. This paper consists of a study into the design of a single piston device SJA and will present all significant data both theoretical and computational regarding its design and performance.

  13. Robust Nonlinear Regulation of Limit Cycle Oscillations in UAVs Using Synthetic Jet Actuators

    Directory of Open Access Journals (Sweden)

    Natalie Ramos Pedroza

    2014-09-01

    Full Text Available In this paper, a synthetic jet actuators (SJA-based nonlinear robust controller is developed, which is capable of completely suppressing limit cycle oscillations (LCO in UAV systems with parametric uncertainty in the SJA dynamics and unmodeled external disturbances. Specifically, the control law compensates for uncertainty in an input gain matrix, which results from the unknown airflow dynamics generated by the SJA. Challenges in the control design include compensation for input-multiplicative parametric uncertainty in the actuator dynamic model. The result was achieved via innovative algebraic manipulation in the error system development, along with a Lyapunov-based robust control law. A rigorous Lyapunov-based stability analysis is utilized to prove asymptotic LCO suppression, considering a detailed dynamic model of the pitching and plunging dynamics. Numerical simulation results are provided to demonstrate the robustness and practical performance of the proposed control law.

  14. The effect of lower hybrid waves on JET plasma rotation

    Science.gov (United States)

    Nave, M. F. F.; Kirov, K.; Bernardo, J.; Brix, M.; Ferreira, J.; Giroud, C.; Hawkes, N.; Hellsten, T.; Jonsson, T.; Mailloux, J.; Ongena, J.; Parra, F.; Contributors, JET

    2017-03-01

    This paper reports on observations of rotation in JET plasmas with lower hybrid current drive. Lower hybrid (LH) has a clear impact on rotation. The changes in core rotation can be either in the co- or counter-current directions. Experimental features that could determine the direction of rotation were investigated. Changes from co- to counter-rotation as the q-profile evolves from above unity to below unity suggests that magnetic shear could be important. However, LH can drive either co- or counter-rotation in discharges with similar magnetic shear and at the same plasma current. It is not clear if a slightly lower density is significant. A power scan at fixed density, shows a lower hybrid power threshold around 3 MW. For smaller LH powers, counter rotation increases with power, while for larger powers a trend towards co-rotation is found. The estimated counter-torque from the LH waves, would not explain the observed angular frequencies, neither would it explain the observation of co-rotation.

  15. PIV EXPERIMENTAL RESEARCH OF INSTANTANEOUS FLOW CHARACTERISTICS OF CIRCULAR ORIFICE SYNTHETIC JET

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The instantaneous flow characteristics of circular orifice synthetic jet was experimentally studied by a phase-locked Particle Image Velocimetry (PIV) system. The instantaneous flowfields, including the forming, developing and breaking down of the vortex for the jet were clearly shown by the PIV experimental results. As the basis of the study of the instantaneous flow, 36 images were taken and phase-averaged for each condition. The PIV experiment was mainly focused on the time evolution of the vortex pairs formed in the push cycle, the saddle point existing in the suck cycle, the variation of the centerline velocity in the whole cycle and the cross-stream velocity profiles and their self-similarity. Finally, the orifice depth was changed from 1.5 mm to 2 mm and 3.5 mm in order to study the effect of different orifice depths on the flow structure, which shows that at all stream wise sections, the peak of the mass flux and momentum flux increases as the orifice depth increases. Furthermore, the nondimensional distance of the mass flux from the exit is the maximum, while the nondimensional distance of the centerline velocity peak from the exit is the minimum, and nondimensional distance of the momentum flux from the exit section is between them.

  16. Atmospheric pressure He-air plasma jet: Breakdown process and propagation phenomenon

    Directory of Open Access Journals (Sweden)

    Asma Begum

    2013-06-01

    Full Text Available In this paper He-discharge (plasma jet/bullet in atmospheric pressure air and its progression phenomenon has been studied experimentally using ICCD camera, optical emission spectroscopy (OES and calibrated dielectric probe measurements. The repetitive nanosecond pulse has applied to a plasma pencil to generate discharge in the helium gas channel. The discharge propagation speed was measured from the ICCD images. The axial electric field distribution in the plasma jet is inferred from the optical emission spectroscopic data and from the probe measurement. The correlation between the jet velocities, jet length with the pulse duration is established. It shows that the plasma jet is not isolated from the input voltage along its propagation path. The discharge propagation speed, the electron density and the local and average electric field distribution along the plasma jet axis predicted from the experimental results are in good agreement with the data predicted by numerical simulation of the streamer propagation presented in different literatures. The ionization phenomenon of the discharge predicts the key ionization parameters, such as speed, peak electric field in the front, and electron density. The maximum local electric field measured by OES is 95 kV/cm at 1.3 cm of the jet axis, and average EF measured by probe is 24 kV/cm at the same place of the jet. The average and local electron density estimated are in the order of 1011 cm-3 and it reaches to the maximum of 1012 cm-3.

  17. A 2D Simulation of the Flow Separation Control over a NACA0015 Airfoil Using a Synthetic Jet Actuator

    Science.gov (United States)

    Boukenkoul, M. A.; Li, F. C.; Aounallah, M.

    2017-03-01

    The present study aims to investigate numerically the flow control possibility using a synthetic jet actuation over a bi-dimensional NACA0015 airfoil manoeuvring at a highly turbulent flow (8.9e105 Reynolds to chord number). The 2-D flow behaviour was computed using the ANSYS Fluent commercial code. The so-called Reynolds Averaged Navier-Stocks (RANS) approach has been tested for one (Spalat-Allmaras S-A) and two (K-ε) transport equations for the turbulence modelling. Both present a weakness to predict the stall angle effectively. The S-A lift coefficient slope seems to be the closest to the experimental data. The synthetic jet control exhibits an extraordinary lift coefficient enhancement at high Angles Of Attack (AOA) but seems to be less obvious at low AOA, where the flow is still attached. A synthetic jet of a Strouhal (St = 2) and momentum (Cμ of 0.56%), delays the stall onset from 15 to 19deg with enhancing the lift coefficient by 40%. The actual work has been enriched by studying the effect of the jet’s frequency and momentum on the lift temporal signal. Also, the interaction between the mean flow and the synthetic jet structures topology was undertaken.

  18. Thermal behavior of bovine serum albumin after exposure to barrier discharge helium plasma jet

    Science.gov (United States)

    Jijie, R.; Pohoata, V.; Topala, I.

    2012-10-01

    Non-thermal plasma jets at atmospheric pressure are useful tools nowadays in plasma medicine. Various applications are tested such as cauterization, coagulation, wound healing, natural and artificial surfaces decontamination, and sterilization. In order to know more about the effects of gas plasma on biological supramolecules, we exposed protein powders to a barrier discharge helium plasma jet. Then, spectroscopic investigations were carried out in order to obtain information on protein secondary, tertiary, and quaternary structures. We obtained a reduction of the protein alpha-helix content after the plasma exposure and a different behavior, for both thermal denaturation/renaturation kinetics and thermal aggregation process.

  19. Jet propagation and medium excitation in a quark–gluon plasma

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Tan; He, Yayun [Key Laboratory of Quark and Lepton Physics (MOE) and Institute of Particle Physics, Central China Normal University, Wuhan 430079 (China); Wang, Xin-Nian [Key Laboratory of Quark and Lepton Physics (MOE) and Institute of Particle Physics, Central China Normal University, Wuhan 430079 (China); Nuclear Science Division Mailstop 70R0319, Lawrence Berkeley National Laboratory, Berkeley, CA 94740 (United States); Zhu, Yan [Departamento de Física de Partículas and IGFAE, Universidade de Santiago de Compostela, E-15706 Santiago de Compostela, Galicia (Spain)

    2014-11-15

    We implement the complete set of elastic 2→2 parton scattering processes in the Linearized Boltzmann Transport (LBT) model to study the parton propagation inside a hot quark–gluon plasma. We calculate and compare the elastic energy loss and the transverse momentum distribution of quarks and gluons. We further simulate a single jet propagation and the induced medium excitation within a static quark–gluon plasma to study how the jet energy and profiles are modified by the jet-medium interaction and in particular the jet-induced wake. Effects of the recoiled thermal partons and the jet-induced wake on the jet energy loss and profiles are studied in detail.

  20. Experimental investigation of a non-thermal atmospheric pressure plasma jet

    Science.gov (United States)

    Begum, Asma

    The main objective of this dissertation is to understand the formation of the plasma jet from the plasma pencil, and the propagation of the plasma jet in the ambient atmosphere where the effect of the external electric field is almost zero. Before investigating the formation and propagation phenomenon of the plasma jet, common physical properties of plasma jets are determined by using the imaging technique and optical emission spectroscopy. The first goal of this dissertation is to establish the laminar helium gas flow channel through a plasma pencil. The formation position, formation time, and the criterion of the plasma jet formation from the discharge chamber of a plasma pencil are investigated by imaging technique, optical emission spectroscopy, and electrical measurement technique. It shows that the plasma jet forms at the surface of the grounded dielectric as a positive plasma front. The formation time of the plasma jet decreases with applied voltage. The maximum power, total power, and average energy to the system and to the discharge are calculated from the total current, discharge current, input potential, and gap potential of the plasma pencil. The calculated average input power with applied voltage to the discharge shows that 56% of the input power is used in the discharge. The total charge in the discharge chamber is calculated by integrating the discharge current waveform. The critical charge in the discharge chamber required to generate a plasma jet is also determined. The propagation phenomenon of the plasma bullet in the ambient atmosphere has been investigated from the velocity curves of the plasma bullet along the jet axis for different applied voltages, pulse widths, and feed gas flow rates. The plasma bullet's velocity is measured by using two different techniques: (i) imaging technique and (ii) electrical technique. In imaging technique, ultra-fast ICCD images of the plasma jet have been taken at different times and positions, and from the

  1. Development of atmospheric pressure large area plasma jet for sterilisation and investigation of molecule and plasma interaction

    Science.gov (United States)

    Zerbe, Kristina; Iberler, Marcus; Jacoby, Joachim; Wagner, Christopher

    2016-09-01

    The intention of the project is the development and improvement of an atmospheric plasma jet based on various discharge forms (e.g. DBD, RF, micro-array) for sterilisation of biomedical equipment and investigation of biomolecules under the influence of plasma stress. The major objective is to design a plasma jet with a large area and an extended length. Due to the success on small scale plasma sterilisation the request of large area plasma has increased. Many applications of chemical disinfection in environmental and medical cleaning could thereby be complemented. Subsequently, the interaction between plasma and biomolecules should be investigated to improve plasma strerilisation. Special interest will be on non equilibrium plasma electrons affecting the chemical bindings of organic molecules.

  2. On the plasma chemistry of a cold atmospheric argon plasma jet with shielding gas device

    Science.gov (United States)

    Schmidt-Bleker, Ansgar; Winter, Jörn; Bösel, André; Reuter, Stephan; Weltmann, Klaus-Dieter

    2016-02-01

    A novel approach combining experimental and numerical methods for the study of reaction mechanisms in a cold atmospheric \\text{Ar} plasma jet is introduced. The jet is operated with a shielding gas device that produces a gas curtain of defined composition around the plasma plume. The shielding gas composition is varied from pure {{\\text{N}}2} to pure {{\\text{O}}2} . The density of metastable argon \\text{Ar}≤ft(4\\text{s}{{,}3}{{\\text{P}}2}\\right) in the plasma plume was quantified using laser atom absorption spectroscopy. The density of long-living reactive oxygen and nitrogen species (RONS), namely {{\\text{O}}3} , \\text{N}{{\\text{O}}2} , \\text{NO} , {{\\text{N}}2}\\text{O} , {{\\text{N}}2}{{\\text{O}}5} and {{\\text{H}}2}{{\\text{O}}2} , was quantified in the downstream region of the jet in a multipass cell using Fourier-transform infrared spectroscopy (FTIR). The jet produces a turbulent flow field and features guided streamers propagating at several \\text{km}~{{\\text{s}}-1} that follow the chaotic argon flow pattern, yielding a plasma plume with steep spatial gradients and a time dependence on the \\text{ns} scale while the downstream chemistry unfolds within several seconds. The fast and highly localized electron impact reactions in the guided streamer head and the slower gas phase reactions of neutrals occurring in the plasma plume and experimental apparatus are therefore represented in two separate kinetic models. The first electron impact reaction kinetics model is correlated to the LAAS measurements and shows that in the guided streamer head primary reactive oxygen and nitrogen species are dominantly generated from \\text{Ar}≤ft(4\\text{s}{{,}3}{{\\text{P}}2}\\right) . The second neutral species plug-flow model hence uses an \\text{Ar}≤ft(4\\text{s}{{,}3}{{\\text{P}}2}\\right) source term as sole energy input and yields good agreement with the RONS measured by FTIR spectroscopy.

  3. Observations of rotation in JET plasmas with electron heating by ion cyclotron resonance heating

    NARCIS (Netherlands)

    Hellsten, T.; Johnson, T. J.; Van Eester, D.; Lerche, E.; Lin, Y.; Mayoral, M. L.; Ongena, J.; Calabro, G.; Crombe, K.; Frigione, D.; Giroud, C.; Lennholm, M.; Mantica, P.; Nave, M. F. F.; Naulin, V.; Sozzi, C.; Studholme, W.; Tala, T.; Versloot, T.

    2012-01-01

    The rotation of L-mode plasmas in the JET tokamak heated by waves in the ion cyclotron range of frequencies (ICRF) damped on electrons, is reported. The plasma in the core is found to rotate in the counter-current direction with a high shear and in the outer part of the plasma with an almost constan

  4. Collective modes of an anisotropic quark-gluon plasma induced by relativistic jets

    CERN Document Server

    Mandal, Mahatsab

    2012-01-01

    We discuss the characteristics of collective modes induced by relativistic jets in an anisotropic quark-gluon plasma(AQGP). Assuming a tsunami-like initial jet distribution, it is found that the dispersion relations for both the stable and unstable modes are modified substantially due to the passage of jet compared to the case when there is no jet. It has also been shown that the growth rate of instability first increases compared to the no jet case and then completely turned into damping except the case when the jet velocity is perpendicular to the wave vector in which case the instability always grows. Thus, the introduction of the jet in the AQGP, in general, might to faster isotropization for the special case when the wave vector is parallel to the anisotropy axis.

  5. Electrothermal efficiency, temperature and thermal conductivity of plasma jet in a DC plasma spray torch

    Indian Academy of Sciences (India)

    G Shanmugavelayutham; V Selvarajan

    2003-12-01

    A study was made to evaluate the electrothermal efficiency of a DC arc plasma torch and temperature and thermal conductivity of plasma jet in the torch. The torch was operated at power levels from 4 to 20 kW in non-transferred arc mode. The effect of nitrogen in combination with argon as plasma gas on the above properties was investigated. Calculations were made from experimental data. The electrothermal efficiency increased significantly with increase in nitrogen content. The plasma jet temperature and thermal conductivity exhibited a decrease with increase in nitrogen content. The experiment was done at different total gas flow rates. The results are explained on the basis of dissociation energy of nitrogen molecules and plasma jet energy loss to the cathode, anode and the walls of the torch.

  6. Numerical simulations of stellar jets and comparison between synthetic and observed maps: clues to the launch mechanism

    CERN Document Server

    Rubini, Francesco; Inghirami, Gabriele; Bacciotti, Francesca; Del Zanna, Luca

    2014-01-01

    High angular resolution spectra obtained with the Hubble Space Telescope Imaging Spectrograph (HST/STIS) provide rich morphological and kinematical information about the stellar jet phenomenon, which allows us to test theoretical models efficiently. In this work, numerical simulations of stellar jets in the propagation region are executed with the PLUTO code, by adopting inflow conditions that arise from former numerical simulations of magnetized outflows, accelerated by the disk-wind mechanism in the launching region. By matching the two regions, information about the magneto-centrifugal accelerating mechanism underlying a given astrophysical object can be extrapolated by comparing synthetic and observed position-velocity diagrams (PVDs). We show that quite different jets, like those from the young T Tauri stars DG-Tau and RW-Aur, may originate from the same disk-wind model for different configurations of the magnetic field at the disk surface. This result supports the idea that all the observed jets may be ...

  7. Experimental characterization of a transition from collisionless to collisional interaction between head-on-merging supersonic plasma jets

    CERN Document Server

    Moser, A L

    2014-01-01

    We present results from experiments on the head-on merging of two supersonic plasma jets in an initially collisionless regime for the counter-streaming ions [A. L. Moser & S. C. Hsu, Phys. Plasmas, submitted (2014)]. The plasma jets are of either an argon/impurity or hydrogen/impurity mixture and are produced by pulsed-power-driven railguns. Based on time- and space-resolved fast-imaging, multi-chord interferometry, and survey-spectroscopy measurements of the overlapping region between the merging jets, we observe that the jets initially interpenetrate, consistent with calculated inter-jet ion collision lengths, which are long. As the jets interpenetrate, a rising mean-charge state causes a rapid decrease in the inter-jet ion collision length. Finally, the interaction becomes collisional and the jets stagnate, eventually producing structures consistent with collisional shocks. These experimental observations can aid in the validation of plasma collisionality and ionization models for plasmas with complex ...

  8. Disinfection of Staphylococcus Aureus by pulsed non-thermal atmospheric plasma jet

    Science.gov (United States)

    Mirpour, Shahriar; Ghoranneviss, Mahmood; Shahgoli, Farhad

    2011-10-01

    The aim of this paper was to study the effect of low-temperature atmospheric plasma jet on non-pathogenic bacteria's colonies. In this regard, Germicidal effect of time and distance of ICP He and He/N2 plasma jet on Staphylococcus Aureus were reported. The gas discharges were generated by a 40 KHz high voltage power supply which led to the inductively coupled plasma. The results showed that He/N2 enhance the sterilization time in comparison of He plasma. To the best of our knowledge this is the first study which has compared the effect of sterilization of ICP Helium and Helium-Nitrogen plasma in listed conditions. Also, the distance dependence showed that the germicidal effect was not linear the distance of electrode and sample. The protein leakage test and SEM of bacteria morphology confirmed the sterilization effect of non-thermal atmospheric pressure plasma jet.

  9. Note: Design and investigation of a multichannel plasma-jet triggered gas switch.

    Science.gov (United States)

    Tie, Weihao; Liu, Xuandong; Zhang, Qiaogen; Liu, Shanhong

    2014-07-01

    We described the fabrication and testing of a multichannel plasma-jet triggered gas switch (MPJTGS). A novel six-channel annular micro-plasma-gun was embedded in the trigger electrode to generate multichannel plasma jets as a nanosecond trigger pulse arrived. The gas breakdown in multiple sites of the spark gap was induced and fixed around jet orifices by the plasma jets. We tested the multichannel discharge characteristics of the MPJTGS in two working modes with charge voltage of 50 kV, trigger voltage of +40 kV (25 ns rise time), and trigger energy of 240 J, 32 J, and 2 J, respectively, at different working coefficients. Results show that the average number of discharge channels increased as the trigger energy increased, and decreased as the working coefficient decreased. At a working coefficient of 87.1% and trigger energy of 240 J, the average number of discharge channels in Mode II could reach 4.1.

  10. Application of CCD Cameras to Investigations of Mixing on Boundaries of a Thermal Plasma Jet

    Institute of Scientific and Technical Information of China (English)

    J.HLINA; J.(S)ONSKY; J.(S)LECHTA

    2007-01-01

    Mixing of a thermal plasma jet with the surrounding atmosphere was studied using two CCD cameras (PCO SensiCam) situated detecting simultaneously the radiation of argon and nitrogen.The evaluation of image differences between two records showed that the location of regions on plasma jet boundaries characterised by stronger nitrogen radiation changes with the plasma flow rate.Close-to-laminar flow results in a small mixing rate and consequently low nitrogen optical emission on plasma jet boundaries.The increase of the flow rate leads to the formation of a relatively thick and stable layer on the boundaries characterised by strong nitrogen radiation.Further enhancement of the flow rate results in the formation of unstable regions of excited nitrogen molecules moving along the jet.

  11. Dynamic Electric Potential Redistribution And Its Influence On The Development Of A Dielectric Barrier Plasma Jet

    Science.gov (United States)

    2012-05-01

    dielectric barrier discharge (DBD) devices. The dielectric barrier plasma jet represents a hybrid between streamer corona and conventional DBD sources...capillary tip and beyond indicating a transition away from a DBD to what was essentially a classical streamer corona discharge drawing current directly...plasma jet generated in a single-electrode dielectric barrier configuration at atmospheric pressure. The influence of dielectric boundary conditions

  12. Spatially resolved spectroscopy of an atmospheric pressure microwave plasma jet used for surface treatment

    OpenAIRE

    Potočňáková Lucia; Hnilica Jaroslav; Kudrle Vít

    2014-01-01

    In this study, the variations of properties of a microwave plasma jet (surfatron) along the discharge axis have been investigated using optical emission spectroscopy. As the argon jet is not enclosed, the spatial distribution of individual species in effluent plasma is the result of rather complicated interplay between energy loss and gradual mixing with the air. Spatial 2D relative intensity profiles of atomic lines and molecular bands at 310 nm, 336 nm, 391 nm and 656 nm are presented in th...

  13. Plasma Jet Interactions with Liquids in Partial Fulfillment of an NRL Karles Fellowship

    Science.gov (United States)

    2015-11-30

    Naval Research Laboratory Washington, DC 20375-5320 NRL /MR/6750--15-9650 Plasma Jet Interactions with Liquids in Partial Fulfillment of an NRL ...ABSTRACT Plasma Jet Interactions with Liquids in Partial Fulfillment of an NRL Karle’s Fellowship Sandra (Hernandez) Hangarter Naval Research Laboratory 4555...Overlook Avenue, SW Washington, DC 20375-5320 NRL /MR/6750--15-9650 ONR Approved for public release; distribution is unlimited. Unclassified Unlimited

  14. Cleaning of carbon materials from flat surfaces and castellation gaps by an atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Stancu, C. [National Institute for Laser, Plasma and Radiation Physics, Atomistilor Str. 409, PO Box Mg36, Magurele-Bucharest, 077125 (Romania); Alegre, D. [Laboratorio Nacional de Fusión, As. Euratom/Ciemat, Avda. Complutense 22, 28040, Madrid (Spain); Ionita, E.R.; Mitu, B. [National Institute for Laser, Plasma and Radiation Physics, Atomistilor Str. 409, PO Box Mg36, Magurele-Bucharest, 077125 (Romania); Grisolia, C. [CEA, IRFM, F-13108, Saint-Paul-lez-Durance (France); Tabares, F.L. [Laboratorio Nacional de Fusión, As. Euratom/Ciemat, Avda. Complutense 22, 28040, Madrid (Spain); Dinescu, G., E-mail: dinescug@infim.ro [National Institute for Laser, Plasma and Radiation Physics, Atomistilor Str. 409, PO Box Mg36, Magurele-Bucharest, 077125 (Romania)

    2016-02-15

    Highlights: • Atmospheric plasma jets operated with nitrogen, oxygen and their mixtures are used for cleaning surfaces of carbon residues • Efficient plasma jet cleaning of carbon deposits from flat surfaces and inside gaps of castellated surfaces is demonstrated • Plasma jet cleaning is more effective at the gaps entrance and on their bottom - Abstract: A study of the removal of carbon layers from flat and castellated surfaces by a plasma jet source operated in open atmosphere is presented. Amorphous hydrogenated carbon films deposited on silicon substrates, on aluminium made castellated surfaces, and graphitic carbon plates were used. The erosion effects of plasmas generated either in pure argon, nitrogen or in their mixtures with hydrogen, ammonia, oxygen are compared. Highest erosion was obtained with nitrogen and nitrogen/oxygen plasmas. Plasmas in argon and containing hydrogen, and ammonia have shown a low erosion rate. A large removal rate by pure nitrogen plasma jet of 3.2 mg/min was found by scanning graphitic carbon flat surfaces for optimum process parameters. Adding small quantities of oxygen led to a removal rate enhancement by a factor of 3. Finally, the integral removal rate of amorphous hydrogenated carbon deposited in gaps 23 mm deep and 0.5 mm wide was of the order of 0.35 mg/min. The layer elimination was more efficient at the top and at the bottom of the gaps, precisely where the thickest codeposits develop in a nuclear fusion device.

  15. The plasma footprint of an atmospheric pressure plasma jet on a flat polymer substrate and its relation to surface treatment

    Science.gov (United States)

    Onyshchenko, Iuliia; Nikiforov, Anton Yu.; De Geyter, Nathalie; Morent, Rino

    2016-08-01

    The aim of this work is to show the correlation between the plasma propagation in the footprint of an atmospheric pressure plasma jet on a flat polymer surface and the plasma treatment impact on the polymer properties. An argon plasma jet working in open air is used as plasma source, while PET thin films are used a substrates for plasma treatment. Light emission photographs are taken with an ICCD camera to have a close look at the generated structures in the plasma jet footprint on the surface. Water contact angle (WCA) measurement and X-ray photoelectron spectroscopy (XPS) analysis are also performed to obtain information about the impact of the plasma treatment on the PET surface characteristics. A variation in ICCD camera gate duration (1 µs, 100 µs, 50 ms) results in the photographs of the different plasma structures occurring during the plasma propagation on the flat PET surface. Contact angle measurements provide results on improvement of the PET hydrophilic character, while XPS analysis shows the distribution of atomic elements on the treated substrate surface. Light emission images help explaining the obtained WCA and XPS results. Contribution to the topical issue "6th Central European Symposium on Plasma Chemistry (CESPC-6)", edited by Nicolas Gherardi, Ester Marotta and Cristina Paradisi

  16. A Laboratory Plasma Experiment for Studying Magnetic Dynamics of Accretion Discs and Jets

    CERN Document Server

    Hsu, S C

    2002-01-01

    This work describes a laboratory plasma experiment and initial results which should give insight into the magnetic dynamics of accretion discs and jets. A high-speed multiple-frame CCD camera reveals images of the formation and helical instability of a collimated plasma, similar to MHD models of disc jets, and also plasma detachment associated with spheromak formation, which may have relevance to disc winds and flares. The plasmas are produced by a planar magnetized coaxial gun. The resulting magnetic topology is dependent on the details of magnetic helicity injection, namely the force-free state eigenvalue alpha_gun imposed by the coaxial gun.

  17. Study of the expansion characteristics of a pulsed plasma jet in air

    Science.gov (United States)

    Zhao, Xuewei; Yu, Yonggang; Mang, Shanshan; Xue, Xiaochun

    2017-04-01

    In the background of electrothermal-chemical (ETC) emission, an investigation has been conducted on the characteristics of a freely expanding pulsed plasma jet in air. The evolutionary process of the plasma jet is experimentally investigated using a piezoelectric pressure sensor and a digital high-speed video system. The variation relation in the extended volume, axial displacement and radial displacement of the pulsed plasma jet in atmosphere with time under different discharge voltages and jet breaking pressures is obtained. Based on experiments, a two-dimensional axisymmetric unsteady model is established to analyze the characteristics of the two-phase interface and the variation of flow-field parameters resulting from a pulsed plasma jet into air at a pressure of 1.5-3.5 MPa under three nozzle diameters (3 mm, 4 mm and 5 mm, respectively). The images of the plasma jet reveal a changing shape process, from a quasi-ellipsoid to a conical head and an elongated cylindrical tail. The axial displacement of the jet is always larger than that along the radial direction. The extended volume reveals a single peak distribution with time. Compared to the experiment, the numerical simulation agrees well with the experimental data. The parameters of the jet field mutate at the nozzle exit with a decrease in the parameter pulse near the nozzle, and become more and more gradual and close to environmental parameters. Increasing the injection pressure and nozzle diameter can increase the parameters of the flow field such as the expansion volume of the pulsed plasma jet, the size of the Mach disk and the pressure. In addition, the turbulent mixing in the expansion process is also enhanced.

  18. Jet flavor tomography of quark gluon plasmas at RHIC and LHC.

    Science.gov (United States)

    Buzzatti, Alessandro; Gyulassy, Miklos

    2012-01-13

    A new Monte Carlo model of jet quenching in nuclear collisions, CUJET1.0, is applied to predict the jet flavor dependence of the nuclear modification factor for fragments f=π,D,B,e(-) from quenched jet flavors g,u,c,b in central collisions at RHIC and LHC. The nuclear modification factors for different flavors are predicted to exhibit a novel level crossing pattern over a transverse momentum range 5jet-medium dynamics in quark gluon plasmas.

  19. Laboratory experiments on plasma jets in a magnetic field using high-power lasers

    Directory of Open Access Journals (Sweden)

    Nishio K.

    2013-11-01

    Full Text Available The experiments to simulate astrophysical jet generation are performed using Gekko XII (GXII HIPER laser system at the Institute of Laser Engineering. In the experiments a fast plasma flow generated by shooting a CH plane (10 μm thickness is observed at the rear side of the plane. By separating the focal spot of the main beams, a non-uniform plasma is generated. The non-uniform plasma flow in an external magnetic field (0.2∼0.3 T perpendicular to the plasma is more collimated than that without the external magnetic field. The plasma β, the ratio between the plasma and magnetic pressure, is ≫ 1, and the magnetic Reynolds number is ∼150 in the collimated plasma. It is considered that the magnetic field is distorted by the plasma flow and enhances the jet collimation.

  20. Laboratory experiments on plasma jets in a magnetic field using high-power lasers

    Science.gov (United States)

    Nishio, K.; Sakawa, Y.; Kuramitsu, Y.; Morita, T.; Ide, T.; Kuwada, M.; Koga, M.; Kato, T.; Norimatsu, T.; Gregory, C.; Woolsey, N.; Murphy, C.; Gregori, G.; Schaar, K.; Diziere, A.; Koenig, M.; Pelka, A.; Wang, S.; Dong, Q.; Li, Y.; Takabe, H.

    2013-11-01

    The experiments to simulate astrophysical jet generation are performed using Gekko XII (GXII) HIPER laser system at the Institute of Laser Engineering. In the experiments a fast plasma flow generated by shooting a CH plane (10 μm thickness) is observed at the rear side of the plane. By separating the focal spot of the main beams, a non-uniform plasma is generated. The non-uniform plasma flow in an external magnetic field (0.2˜0.3 T) perpendicular to the plasma is more collimated than that without the external magnetic field. The plasma β, the ratio between the plasma and magnetic pressure, is ≫ 1, and the magnetic Reynolds number is ˜150 in the collimated plasma. It is considered that the magnetic field is distorted by the plasma flow and enhances the jet collimation.

  1. Control of ROS and RNS productions in liquid in atmospheric pressure plasma-jet system

    Science.gov (United States)

    Uchida, Giichiro; Ito, Taiki; Takenaka, Kosuke; Ikeda, Junichiro; Setsuhara, Yuichi

    2016-09-01

    Non-thermal plasma jets are of current interest in biomedical applications such as wound disinfection and even treatment of cancer tumors. Beneficial therapeutic effects in medical applications are attributed to excited species of oxygen and nitrogen from air. However, to control the production of these species in the plasma jet is difficult because their production is strongly dependent on concentration of nitrogen and oxygen from ambient air into the plasma jet. In this study, we analyze the discharge characteristics and the ROS and RNS productions in liquid in low- and high-frequency plasma-jet systems. Our experiments demonstrated the marked effects of surrounding gas near the plasma jet on ROS and RNS productions in liquid. By controlling the surround gas, the O2 and N2 main plasma jets are selectively produced even in open air. We also show that the concentration ratio of NO2- to H2O2 in liquid is precisely tuned from 0 to 0.18 in deionized water by changing N2 gas ratio (N2 / (N2 +O2)) in the main discharge gas, where high NO2- ratio is obtained at N2 gas ratio at N2 / (N2 +O2) = 0 . 8 . The low-frequency plasma jet with controlled surrounding gas is an effective plasma source for ROS and RNS productions in liquid, and can be a useful tool for biomedical applications. This study was partly supported by a Grant-in-Aid for Scientific Research on Innovative Areas ``Plasma Medical Innovation'' (24108003) from the Ministry of Education, Culture, Sports, Science and Technology, Japan (MEXT).

  2. Thermalization of mini-jets in a quark-gluon plasma

    Directory of Open Access Journals (Sweden)

    Iancu Edmond

    2016-01-01

    Full Text Available We present the complete physical picture for the evolution of a high-energy jet propagating through a weakly-coupled quark-gluon plasma (QGP by analytical and numerical investigation of thermalization of the soft components of the jet. Our results support the following physical picture: the leading particle emits a significant number of mini-jets which promptly evolve via multiple branching and thus degrade into a myriad of soft gluons, with energies of the order of the medium temperature T. Via elastic collisions with the medium constituents, these soft gluons relax to local thermal equilibrium with the plasma over a time scale which is considerably shorter than the typical lifetime of the mini-jet. The thermalized gluons form a tail which lags behind the hard components of the jet. Together with the background QGP, they behave hydrodynamically.

  3. Thermalization of mini-jets in a quark–gluon plasma

    Energy Technology Data Exchange (ETDEWEB)

    Iancu, Edmond, E-mail: edmond.iancu@cea.fr; Wu, Bin, E-mail: bin.wu.phys@gmail.com [Institut de Physique Théorique, CEA Saclay, CNRS UMR 3681, F-91191 Gif-sur-Yvette (France); Department of Physics, The Ohio State University, Columbus, OH 43210 (United States)

    2016-12-15

    We present the complete physical picture for the evolution of a high-energy jet propagating through a weakly-coupled quark-gluon plasma (QGP) by analytical and numerical investigation of thermalization of the soft components of the jet. Our results support the following physical picture: the leading particle emits a significant number of mini-jets which promptly evolve via multiple branching and thus degrade into a myriad of soft gluons, with energies of the order of the medium temperature T. Via elastic collisions with the medium constituents, these soft gluons relax to local thermal equilibrium with the plasma over a time scale which is considerably shorter than the typical lifetime of the mini-jet. The thermalized gluons form a tail which lags behind the hard components of the jet. Together with the background QGP, they behave hydrodynamically.

  4. Thermalization of mini-jets in a quark-gluon plasma

    Science.gov (United States)

    Iancu, Edmond; Wu, Bin

    2016-12-01

    We present the complete physical picture for the evolution of a high-energy jet propagating through a weakly-coupled quark-gluon plasma (QGP) by analytical and numerical investigation of thermalization of the soft components of the jet. Our results support the following physical picture: the leading particle emits a significant number of mini-jets which promptly evolve via multiple branching and thus degrade into a myriad of soft gluons, with energies of the order of the medium temperature T. Via elastic collisions with the medium constituents, these soft gluons relax to local thermal equilibrium with the plasma over a time scale which is considerably shorter than the typical lifetime of the mini-jet. The thermalized gluons form a tail which lags behind the hard components of the jet. Together with the background QGP, they behave hydrodynamically.

  5. Properties of Atmospheric Pressure Ar Plasma Jet Depending on Treated Dielectric Material

    Science.gov (United States)

    Prysiazhnyi, Vadym; Ricci Castro, Alonso H.; Kostov, Konstantin G.

    2017-02-01

    Atmospheric pressure plasma jet operated in argon was utilized to modify surfaces of glass, acrylic, and PTFE dielectrics. This paper describes the influence of the dielectric substrate on operation and properties of plasma. Two modes of operation (each of those have two patterns) were described. The transition from one mode to another, values of the dissipated power, and spreading of plasma over the dielectric surfaces strongly depended on the substrate material. Additionally, three methods of plasma spreading estimation were presented and discussed.

  6. [Investigation on the Spectral Characteristics of a Plasma Jet in Atmospheric Argon Glow Discharge].

    Science.gov (United States)

    Li, Xue-chen; Zhang, Chun-yan; Li, Ji-yuan; Bao, Wen-ting

    2015-12-01

    Plasma jet is a kind of important plasma source at atmospheric pressure. In recent years, it becomes an important hot topic in the field of low temperature plasma. In this paper, using a tungsten needle and a tungsten wire mesh, a direct-current excited jet is developed to operate in argon at atmospheric pressure. In the atmospheric pressure argon, the plasma jet can produce a stable plasma plume. By using the method of emission spectroscopy, the parameters of the plasma plume are investigated. The discharge emits dazzling white light from the area between the tungsten needle electrode and the wire mesh electrode. A plasma plume with a flame shape appears outside the tungsten wire mesh electrode. For a constant value of voltage (U = 13.5 kV), the length of the plasma plume increases with the gas flow rate. For a constant value of the gas flow rate(10 L · min⁻¹), the length of the plasma plume increases with the voltage. The voltage is inversely proportional to the current under the constant gas flow rate. In other words, the voltage decreases with the discharge current, which indicates that a glow discharge is formed in the plasma jet. Optical emission spectrum in 300 to 800 nm is collected from the direct-current excited plasma jet. By Boltzmann plot method, the excited electron temperature of the plasma plume is investigated as a function of the applied voltage or the gas flow rate. Results show that the excited electron temperature increases with decreasing applied voltage under the constant gas flow. Moreover, it increases with decreasing the gas flow under the constant voltage. Based on the discharge theory, these experimental phenomena are explained qualitatively. These results are of great importance to the development of atmospheric pressure uniform discharge plasma source and its application in industrial field.

  7. Numerical and experimental study on a pulsed-dc plasma jet

    Science.gov (United States)

    Liu, X. Y.; Pei, X. K.; Lu, X. P.; Liu, D. W.

    2014-06-01

    A numerical and experimental study of plasma jet propagation in a low-temperature, atmospheric-pressure, helium jet in ambient air is presented. A self-consistent, multi-species, two-dimensional axially symmetric plasma model with detailed finite-rate chemistry of helium-air mixture composition is used to provide insights into the propagation of the plasma jet. The obtained simulation results suggest that the sheath forms near the dielectric tube inner surface and shields the plasma channel from the tube surface. The strong electric field at the edge of the dielectric field enhances the ionization in the air mixing layer; therefore, the streamer head becomes ring-shaped when the streamer runs out of the tube. The avalanche-to-streamer transition is the main mechanism of streamer advancement. Penning ionization dominates the ionization reactions and increases the electrical conductivity of the plasma channel. The simulation results are supported by experimental observations under similar discharge conditions.

  8. Optical Emission Spectroscopy of an Atmospheric Pressure Plasma Jet During Tooth Bleaching Gel Treatment.

    Science.gov (United States)

    Šantak, Vedran; Zaplotnik, Rok; Tarle, Zrinka; Milošević, Slobodan

    2015-11-01

    Optical emission spectroscopy was performed during atmospheric pressure plasma needle helium jet treatment of various tooth-bleaching gels. When the gel sample was inserted under the plasma plume, the intensity of all the spectral features increased approximately two times near the plasma needle tip and up to two orders of magnitude near the sample surface. The color change of the hydroxylapatite pastille treated with bleaching gels in conjunction with the atmospheric pressure plasma jet was found to be in correlation with the intensity of OH emission band (309 nm). Using argon as an additive to helium flow (2 L/min), a linear increase (up to four times) of OH intensity and, consequently, whitening (up to 10%) of the pastilles was achieved. An atmospheric pressure plasma jet activates bleaching gel, accelerates OH production, and accelerates tooth bleaching (up to six times faster).

  9. Development of a new atmospheric pressure cold plasma jet generator and application in sterilization

    Institute of Scientific and Technical Information of China (English)

    Cheng Cheng; Liu Peng; Xu Lei; Zhang Li-Ye; Zhan Ru-Juan; Zhang Wen-Rui

    2006-01-01

    This paper reports that a new plasma generator at atmospheric pressure, which is composed of two homocentric cylindrical all-metal tubes, successfully generates a cold plasma jet. The inside tube electrode is connected to ground,the outside tube electrode is connected to a high-voltage power supply, and a dielectric layer is covered on the outside tube electrode. When the reactor is operated by low-frequency (6 kHz-20 kHz) AC supply in atmospheric pressure and argon is steadily fed as a discharge gas through inside tube electrode, a cold plasma jet is blown out into air and the plasma gas temperature is only 25-30 ℃. The electric character of the discharge is studied by using digital real-time oscilloscope (TDS 200-Series), and the discharge is capacitive. Preliminary results are presented on the decontamination of E.colis bacteria and Bacillus subtilis bacteria by this plasma jet, and an optical emission analysis of the plasma jet is presented in this paper. The ozone concentration generated by the plasma jet is 1.0 × 1016cm-3 which is acquired by using the ultraviolet absorption spectroscopy.

  10. Enhanced electron yield from a laser-plasma accelerator using high-Z gas jet targets

    CERN Document Server

    Mirzaie, Mohammad; Li, Song; Sokollik, Thomas; He, Fei; Cheng, Ya; Sheng, Zhengming; Zhang, Jie

    2014-01-01

    An investigation of the multi-hundred MeV electron beam yield (charge) form helium, nitrogen, neon and argon gas jet plasmas in a laser-plasma wakefield acceleration experiment was carried out. The charge measurement has been made via imaging the electron beam intensity profile on a fluorescent screen into a 14-bit charge coupled device (CCD) which was cross-calibrated with nondestructive electronics-based method. Within given laser and plasma parameters, we found that laser-driven low Z- gas jet targets generate high-quality and well-collimated electron beams with reasonable yields at the level of 10-100 pC. On the other hand, filamentary electron beams which were observed from high-Z gas jets at higher densities reached much higher yield. Evidences for cluster formation were clearly observed in high-Z gases, especially in the argon gas jet target where we received the highest yield of ~ 3 nC

  11. Modeling of the merging, liner formation, implosion of hypervelocity plasma jets for the PLX- α project

    Science.gov (United States)

    Cassibry, Jason; Hsu, Scott; Schillo, Kevin; Samulyak, Roman; Stoltz, Peter; Beckwith, Kris

    2015-11-01

    A suite of numerical tools will support the conical and 4 π plasma-liner-formation experiments for the PLX- α project. A new Lagrangian particles (LP) method will provide detailed studies of the merging of plasma jets and plasma-liner formation/convergence. A 3d smooth particle hydrodynamic (SPH) code will simulate conical (up to 9 jets) and 4 π spherical (up to 60 jets) liner formation and implosion. Both LP and SPH will use the same tabular EOS generated by Propaceos, thermal conductivity, optically thin radiation and physical viscosity models. With LP and SPH,the major objectives are to study Mach-number degradation during jet merging, provide RMS amplitude and wave number of the liner nonuniformity at the leading edge, and develop scaling laws for ram pressure and liner uniformity as a function of jet parameters. USIM, a 3D multi-fluid plasma code, will be used to perform 1D and 2D simulations of plasma-jet-driven magneto-inertial fusion (PJMIF) to identify initial conditions in which the ``liner gain'' exceeds unity. A brief overview of the modeling program will be provided. Results from SPH modeling to support the PLX- α experimental design will also be presented, including preliminary ram-pressure scaling and non-uniformity characterization.

  12. Modeling and Simulation for Nanoparticle Plasma Jet Diagnostic Probe for Runaway Electron Beam-Plasma Interaction

    Science.gov (United States)

    Bogatu, I. N.; Galkin, S. A.

    2016-10-01

    The C60 nanoparticle plasma jet (NPPJ) rapid injection into a tokamak major disruption is followed by C60 gradual fragmentation along plasma-traversing path. The result is abundant C ion concentration in the core plasma enhancing the potential to probe and diagnose the runaway electrons (REs) during different phases of their dynamics. A C60/C NPPJ of 75 mg, high-density (>1023 m-3) , hyper-velocity (>4 km/s), and uniquely fast response-to-delivery time ( 1 ms) has been demonstrated on a test bed. It can rapidly and deeply deliver enough mass to increase electron density to 2.4x1021 m-3, 60 times larger than typical DIII-D pre-disruption value. We will present the results of our on-going work on: 1) self-consistent model for RE current density evolution (by Dreicer mechanism and ``avalanche'') focused on the effect of fast and deep deposition of C ions, 2) improvement of single C60q+ fragmenting ion penetration model through tokamak B(R)-field and post-TQ plasma, and 3) simulation of C60q+ PJ penetration through the DIII-D characteristic 2 T B-field to the RE beam central location by using the Hybrid Electro-Magnetic 2D code (HEM-2D. Work supported by US DOE DE-SC0015776 Grant.

  13. First plasma operation of the enhanced JET vertical stabilisation system

    NARCIS (Netherlands)

    Rimini, F. G.; Crisanti, F.; Albanese, R.; Ambrosino, G.; Ariola, M.; Artaserse, G.; Bellizio, T.; Coccorese, V.; De Tommasi, G.; P. de Vries,; Lomas, P. J.; Maviglia, F.; Neto, A.; Nunes, I.; Pironti, A.; Ramogida, G.; Sartori, F.; Shaw, S. R.; Tsalas, M.; Vitelli, R.; Zabeo, L.

    2011-01-01

    A project dedicated to the enhancement of the JET vertical stabilization system was launched in 2006, including an upgrade of the Power Supply of the Radial Field Amplifier, of hardware and software of the vertical stabilization control system. The main aim was to double the JET capability in stabil

  14. Fundamental ion cyclotron resonance heating of JET deuterium plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Krasilnikov, A. V. [Troitsk Institute of Nuclear Physics (TRINITI), Russia; Van Eester, D. [Laboratory for Plasma Physics-ERM/KMS (LPP-ERM/KMS), Brussels, Belgium; Lerche, E. [Laboratory for Plasma Physics-ERM/KMS (LPP-ERM/KMS), Brussels, Belgium; Ongena, J. [Laboratory for Plasma Physics-ERM/KMS (LPP-ERM/KMS), Brussels, Belgium; Amosov, V. N. [Troitsk Institute of Nuclear Physics (TRINITI), Russia; Biewer, Theodore M [ORNL; Bonheure, G. [Laboratory for Plasma Physics-ERM/KMS (LPP-ERM/KMS), Brussels, Belgium; Crombe, K. [Ghent University, Belgium; Ericsson, G. [Uppsala University, Uppsala, Sweden; Esposito, Basilio [ENEA, Frascati; Giacomelli, L. [Uppsala University, Uppsala, Sweden; Hellesen, C. [Uppsala University, Uppsala, Sweden; Hjalmarsson, A. [Uppsala University, Uppsala, Sweden; Jachmich, S. [EURATOM / UKAEA, UK; Kallne, J. [Uppsala University, Uppsala, Sweden; Kaschuck, Yu A [Troitsk Institute of Nuclear Physics (TRINITI), Russia; Kiptily, V. [EURATOM / UKAEA, UK; Leggate, H. [EURATOM / UKAEA, UK; Mailloux, J. [EURATOM / UKAEA, UK; Marocco, D. [ENEA, Frascati; Mayoral, M.-L. [EURATOM / UKAEA, UK; Popovichev, S. [EURATOM / UKAEA, UK; Riva, M. [ENEA, Frascati; Santala, M. [EURATOM / UKAEA, UK; Stamp, M. F. [EURATOM / UKAEA, UK; Vdovin, V. [Russian Research Center, Kurchatov Institute, Moscow, Russia; Walden, A. [EURATOM / UKAEA, UK

    2009-03-01

    Radio frequency heating of majority ions is of prime importance for understanding the basic role of auxiliary heating in the activated D T phase of ITER. Majority deuterium ion cyclotron resonance heating (ICRH) experiments at the fundamental cyclotron frequency were performed in JET. In spite of the poor antenna coupling at 25 MHz, this heating scheme proved promising when adopted in combination with D neutral beam injection (NBI). The effect of fundamental ICRH of a D population was clearly demonstrated in these experiments: by adding ~25% of heating power the fusion power was increased up to 30 50%, depending on the type of NBI adopted. At this power level, the ion and electron temperatures increased from Ti ~ 4.0 keV and Te ~ 4.5 keV (NBI-only phase) to Ti ~ 5.5 keV and Te ~ 5.2 keV (ICRH + NBI phase), respectively. The increase in the neutron yield was stronger when 80 keV rather than 130 keV deuterons were injected in the plasma. It is shown that the neutron rate, the diamagnetic energy and the electron as well as the ion temperature scale roughly linearly with the applied RF power. A synergistic effect of the combined use of ICRF and NBI heating was observed: (i) the number of neutron counts measured by the neutron camera during the combined ICRF + NBI phases of the discharges exceeded the sum of the individual counts of the NBI-only and ICRF-only phases; (ii) a substantial increase in the number of slowing-down beam ions was detected by the time of flight neutron spectrometer when ICRF power was switched on; (iii) a small D subpopulation with energies slightly above the NBI launch energy was detected by the neutral particle analyzer and -ray spectroscopy.

  15. Modeling the plasma chemistry of stratospheric Blue Jet streamers

    Science.gov (United States)

    Winkler, Holger; Notholt, Justus

    2014-05-01

    Stratospheric Blue Jets (SBJs) are upward propagating discharges in the altitude range 15-40 km above thunderstorms. The currently most accepted theory associates SBJs to the development of the streamer zone of a leader. The streamers emitted from the leader can travel for a few tens of kilometers predominantly in the vertical direction (Raizer et al., 2007). The strong electric fields at the streamer tips cause ionisation, dissociation, and excitation, and give rise to chemical perturbations. While in recent years the effects of electric discharges occurring in the mesosphere (sprites) have been investigated in a number of model studies, there are only a few studies on the impact of SBJs. However, chemical perturbations due to SBJs are of interest as they might influence the stratospheric ozone layer. We present results of detailed plasma chemistry simulations of SBJ streamers for both day-time and night-time conditions. Any effects of the subsequent leader are not considered. The model accounts for more than 500 reactions and calculates the evolution of the 88 species under the influence of the breakdown electric fields at the streamer tip. As the SBJ dynamics is outside the scope of this study, the streamer parameters are prescribed. For this purpose, electric field parameters based on Raizer et al. (2007) are used. The model is applied to the typical SBJ altitude range 15-40 km. The simulations indicate that SBJ streamers cause significant chemical perturbations. In particular, the liberation of atomic oxygen during the discharge leads to a formation of ozone. At the same time, reactive nitrogen and hydrogen radicals are produced which will cause catalytic ozone destruction. Reference: Raizer et al. (2007), J. Atmos. Solar-Terr. Phys., 69 (8), 925-938.

  16. Active Vibration Control of an S809 Wind Turbine Blade Using Synthetic Jet Actuators

    Science.gov (United States)

    Maldonado, Victor; Boucher, Matthew; Ostman, Rebecca; Amitay, Michael

    2009-11-01

    Active flow control via synthetic jet actuators was implemented to improve the aeroelastic performance of a small scale S809 airfoil wind turbine blade model in a wind tunnel. Blade vibration performance was explored for a range of steady post-stall angles of attack, as well as various unsteady pitching motions for a chord based Reynolds number range of 1.29x10^5 to 3.69x10^5. Blade tip deflection was measured using a pair of calibrated strain gauges mounted at the root of the model. Using flow control, significant vibration reduction was observed for some steady post-stall angles of attack, while for dynamic pitching motions, vibration reduction was more pronounced (for a given angle of attack) on the pitch up motion compared to the pitch down motion of the blade cycle. This effect was attributed to the phenomenon known as dynamic stall, where the shedding of a leading edge vortex during the pitch up motion contributes to elevated values of lift (compared to static angles of attack) and lower values of lift when the blade is pitched down. This effect was also quantified through the use of Particle Image Velocimetry.

  17. A novel optimal design for an application-oriented synthetic jet actuator

    Institute of Scientific and Technical Information of China (English)

    Deng Xiong; Xia Zhixun; Luo Zhenbing; Wang Lin

    2014-01-01

    The evaluation indicator for the performance of a synthetic jet actuator (SJA) is well-defined because of its various applications, which require optimal design to improve its performance and extend its field of application. This paper presents a novel approach to the optimal design of an SJA applied to enhance fuel/air mixture. It optimizes the combination of an actuator’s geometric parameters by selecting the strength of vortex pairs as the evaluation indicator, coupled with orthogonal experiments and analysis of variance (AOV). The results indicate that slot width is the most notable factor influencing the strength of vortex pairs, followed by cavity height and slot depth. The optimal value of the strength of vortex pairs increases by 32.5%over the experimental data of the base case, and more than 8.4%compared with the simulation results of the orthogonal experiments. It is concluded that the optimal method can effectively improve the performance of an SJA applied in mixing enhancement, reducing the test numbers and the associated design cycle and cost.

  18. Delayed Detached Eddy Simulation of Flow Over an Airfoil with Synthetic Jet Control

    Science.gov (United States)

    Lopez, Omar; Uday, Godse; Moser, Robert

    2007-11-01

    Delayed Detached-Eddy Simulation (DDES) is a hybrid RANS-LES model similar to DES but with modifications to reduce the influences of ambiguous grid densities in the numerical results. This model was implemented in CDP, a parallel unstructured grid incompressible flow solver, developed at the Center for Integrated Turbulence Simulations (CITS) at Stanford University. CDP has the advantage of being nearly energy conserving. Several simulations at static angles of attack at a Re based on the chord of 5.7e5 showed good agreement with experiments and other computational studies. Simulations of pitching and plunging cases have also yield good results. This simulation capability is being used to model closed-loop flow control of the airfoil. The action of tangential-blowing synthetic jet actuators mounted near the trailing edge of the airfoil are modeled as local momentum sources, based on detailed measurements of this configuration conducted at Georgia Tech. Resulting simulations show the effects of the actuators on the vortical structure of the flow, as well as on the aerodynamic properties. By integrating actuator and sensor models with a model of the flow controller, we will be able to simulate experiments currently being conducted by A.Glezer and his group at Georgia Tech. on the control of an airfoil in a wind tunnel.

  19. Laser Doppler vibrometry experiment on a piezo-driven slot synthetic jet in water

    Directory of Open Access Journals (Sweden)

    Broučková Zuzana

    2015-01-01

    Full Text Available The present study deals with a slot synthetic jet (SJ issuing from an actuator into quiescent surroundings and driven by a piezoceramic transducer. The actuator slot width was 0.36 mm, with a drive frequency proposed near the theoretical natural frequency of the actuator. The working fluid was water at room temperature. The present experiments used flow visualization (a laser-induced fluorescence technique and laser Doppler vibrometry methods. Flow visualization was used to identify SJ formation, to demonstrate its function, and to estimate SJ velocity. Laser Doppler vibrometry was used to quantify diaphragm displacement and refine operating parameters. Phase averaging yielded a spatial and temporal diaphragm deflection during the actuation period. Taking incompressibility and continuity into consideration, the velocity in the actuator slot and the Reynolds number of the SJ were evaluated as 0.21 m/s and 157, respectively. The present results confirmed a SJ actuator function at the resonance frequency of approximately 46 Hz, which corresponds closely with the theoretical evaluation. The laser Doppler vibrometry results corresponded closely with an estimation of SJ velocity by the present flow visualization.

  20. Atmospheric nonequilibrium mini-plasma jet created by a 3D printer

    Energy Technology Data Exchange (ETDEWEB)

    Takamatsu, Toshihiro, E-mail: toshihiro@plasma.es.titech.ac.jp [Kobe University Graduate School of Medicine, Department of Gastroenterology, 7-5-1 Kusunoki-cho, Chuo-ku, Kobe, 650-0017 (Japan); Tokyo Institute of Technology, Department of Energy Sciences, J2-32, 4259 Nagatsuta, Midori-ku, Yokohama, 226-8502 (Japan); Kawano, Hiroaki; Miyahara, Hidekazu; Okino, Akitoshi [Tokyo Institute of Technology, Department of Energy Sciences, J2-32, 4259 Nagatsuta, Midori-ku, Yokohama, 226-8502 (Japan); Azuma, Takeshi [Kobe University Graduate School of Medicine, Department of Gastroenterology, 7-5-1 Kusunoki-cho, Chuo-ku, Kobe, 650-0017 (Japan)

    2015-07-15

    In this study, a small-sized plasma jet source with a 3.7 mm head diameter was created via a 3D printer. The jet’s emission properties and OH radical concentrations (generated by argon, helium, and nitrogen plasmas) were investigated using optical emission spectrometry (OES) and electron spin resonance (ESR). As such, for OES, each individual gas plasma propagates emission lines that derive from gases and ambient air inserted into the measurement system. For the case of ESR, a spin adduct of the OH radical is typically observed for all gas plasma treatment scenarios with a 10 s treatment by helium plasma generating the largest amount of OH radicals at 110 μM. Therefore, it was confirmed that a plasma jet source made by a 3D printer can generate stable plasmas using each of the aforementioned three gases.

  1. Atmospheric nonequilibrium mini-plasma jet created by a 3D printer

    Directory of Open Access Journals (Sweden)

    Toshihiro Takamatsu

    2015-07-01

    Full Text Available In this study, a small-sized plasma jet source with a 3.7 mm head diameter was created via a 3D printer. The jet’s emission properties and OH radical concentrations (generated by argon, helium, and nitrogen plasmas were investigated using optical emission spectrometry (OES and electron spin resonance (ESR. As such, for OES, each individual gas plasma propagates emission lines that derive from gases and ambient air inserted into the measurement system. For the case of ESR, a spin adduct of the OH radical is typically observed for all gas plasma treatment scenarios with a 10 s treatment by helium plasma generating the largest amount of OH radicals at 110 μM. Therefore, it was confirmed that a plasma jet source made by a 3D printer can generate stable plasmas using each of the aforementioned three gases.

  2. Development of a non-equilibrium 60 MHz plasma jet with a long discharge plume

    Science.gov (United States)

    Uchida, Giichiro; Kawabata, Kazufumi; Ito, Taiki; Takenaka, Kosuke; Setsuhara, Yuichi

    2017-07-01

    High-frequency plasma jets driven by voltages in the frequency range of 6-60 MHz are developed. A long plasma jet, 40 mm in length, is successfully produced by using a pair of ring electrodes outside a quartz tube. The electrode pair consists of a wide power electrode and a narrow ground electrode that is positioned at the head of the tube. The ratio of the length of the ground electrode to the length of the power electrode must be small in order to produce long plasma jets. The high-frequency plasma jet is operated in a non-thermal-equilibrium state at a gas temperature of around 60 °C. Operation at the very-high-frequency of 60 MHz leads to a lower discharge voltage and lower electron energy compared to lower frequencies of 6 and 13.56 MHz. The ability of the very-high-frequency (60 MHz) plasma jet to produce reactive oxygen and nitrogen species in water is also investigated. High H2O2 and NO3- concentrations of more than 1 mmol/l are realized by irradiating 3 ml of deionized water with the plasma for a short period of 2 min.

  3. A Sliding Mode LCO Regulation Strategy for Dual-Parallel Underactuated UAV Systems Using Synthetic Jet Actuators

    OpenAIRE

    N. Ramos-Pedroza; MacKunis, W.; Reyhanoglu, M.

    2015-01-01

    A sliding mode control- (SMC-) based limit cycle oscillation (LCO) regulation method is presented, which achieves asymptotic LCO suppression for UAVs using synthetic jet actuators (SJAs). With a focus on applications involving small UAVs with limited onboard computational resources, the controller is designed with a simplistic structure, requiring no adaptive laws, function approximators, or complex calculations in the control loop. The control law is rigorously proven to achieve asymptoti...

  4. Fire Protection Safety Evaluations of Hydro-Treated Renewable Jet (HRJ) and Synthetic Paraffinic Kerosene (SPK) Fuels

    Science.gov (United States)

    2012-04-30

    first responder must be established. The objective of this study was to measure alternative fuel safety parameters. Flame propagation tests documented the flame spread rate on liquid fuel surfaces. Flame visible spectrum emissions were measured in normal and elevated oxygen concentration environments. Commercial optical flame detectors (OFDs) and commercial combustible gas detectors (CGDs) were evaluated for their relative response to and ability to detect bio-oil derived hydroprocessed renewable jet (HRJ) and synthetic paraffinic kerosene (SPK) fuel fires and vapors as

  5. Atmospheric pressure resistive barrier air plasma jet induced bacterial inactivation in aqueous environment

    Science.gov (United States)

    Thiyagarajan, Magesh; Sarani, Abdollah; Gonzales, Xavier

    2013-03-01

    An atmospheric pressure resistive barrier air plasma jet is designed to inactivate bacteria in aqueous media in direct and indirect exposure modes of treatment. The resistive barrier plasma jet is designed to operate at both dc and standard 50-60 Hz low frequency ac power input and the ambient air at 50% humidity level was used as the operating gas. The voltage-current characteristics of the plasma jet were analyzed and the operating frequency of the discharge was measured to be 20 kHz and the plasma power was measured to be 26 W. The plasma jet rotational temperatures (Trot) are obtained from the optical emission spectra, from the N2C-B(2+) transitions by matching the experimental spectrum results with the Spectra Air (SPECAIR) simulation spectra. The reactive oxygen and nitrogen species were measured using optical emission spectroscopy and gas analyzers, for direct and indirect treatment modes. The nitric oxides (NO) were observed to be the predominant long lived reactive nitrogen species produced by the plasma. Three different bacteria including Staphylococcus aureus (Gram-positive), Escherichia coli (Gram-negative), and Neisseria meningitidis (Gram-negative) were suspended in an aqueous media and treated by the resistive barrier air plasma jet in direct and indirect exposure modes. The results show that a near complete bacterial inactivation was achieved within 120 s for both direct and indirect plasma treatment of S. aureus and E. coli bacteria. Conversely, a partial inactivation of N. meningitidis was observed by 120 s direct plasma exposure and insignificant inactivation was observed for the indirect plasma exposure treatment. Plasma induced shifts in N. meningitidis gene expression was analyzed using pilC gene expression as a representative gene and the results showed a reduction in the expression of the pilC gene compared to untreated samples suggesting that the observed protection against NO may be regulated by other genes.

  6. Identification of the ubiquitous Coriolis momentum pinch in JET tokamak plasmas

    NARCIS (Netherlands)

    Weisen, H.; Camenen, Y.; Salmi, A.; Versloot, T. W.; de Vries, P. C.; Maslov, M.; Tala, T.; Beurskens, M.; Giroud, C.

    2012-01-01

    A broad survey of the experimental database of neutral beam heated plasmas in the JET tokamak has established the theoretically expected ubiquity, in rotating plasmas, of a convective transport mechanism which has its origin in the vertical particle drift resulting from the Coriolis force. This inwa

  7. Simulation of coal conversion in Ar/H{sub 2} plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Y.J.; Chen, H.G.; Bao, W.R.; Li, F.; Zhu, S.Y.; Xie, K.C. [Taiyuan University of Technology, Taiyuan (China). Shanxi Key Lab of Coal Science and Technology

    1999-07-01

    Coal conversion arc plasma was estimated by the combination of energy balance and chemical percolation devolatilization model. The velocity of particles was calculated by momentum equations and the temperature of particles and plasma jet was calculated by heat transfer equations. 11 refs., 2 figs., 4 tabs.

  8. Improved Confinement in JET High {beta} Plasmas with an ITER-Like Wall

    CERN Document Server

    Challis, C D; Beurskens, M; Buratti, P; Delabie, E; Drewelow, P; Frassinetti, L; Giroud, C; Hawkes, N; Hobirk, J; Joffrin, E; Keeling, D; King, D B; Maggi, C F; Mailloux, J; Marchetto, C; McDonald, D; Nunes, I; Pucella, G; Saarelma, S; Simpson, J

    2015-01-01

    The replacement of the JET carbon wall (C-wall) by a Be/W ITER-like wall (ILW) has affected the plasma energy confinement. To investigate this, experiments have been performed with both the C-wall and ILW to vary the heating power over a wide range for plasmas with different shapes.

  9. DNA strand scission induced by a non-thermal atmospheric pressure plasma jet.

    Science.gov (United States)

    Ptasińska, Sylwia; Bahnev, Blagovest; Stypczyńska, Agnieszka; Bowden, Mark; Mason, Nigel J; Braithwaite, Nicholas St J

    2010-07-28

    The DNA molecule is observed to be very susceptible to short-term exposures to an atmospheric pressure plasma jet. The DNA damage induced by plasma-generated species, i.e. excited atoms, charged particles, electrons and UV light is determined.

  10. Electronic ground state OH(X) radical in a low-temperature atmospheric pressure plasma jet

    Science.gov (United States)

    Fuh, Che A.; Clark, Shane M.; Wu, Wei; Wang, Chuji

    2016-10-01

    The wide applicability of atmospheric pressure plasma jets in biomedicine stems from the presence of reactive nitrogen and oxygen species generated in these plasma jets. Knowing the absolute concentration of these reactive species is of utmost importance as it is critical, along with the particle flux obtained from the plasma feed gas flow rate to ensure that the correct dosage is applied during applications. In this study, we investigate and report the ground state OH(X) number density acquired using cavity ringdown spectroscopy, along the propagation axis (z-axis) of a cold atmospheric pressure helium plasma plume. The jet was generated by a repetitively pulsed mono-polar square wave of duration 1 μs running at a frequency of 9.9 kHz. The voltage supplied was 6.5 kV with the helium flow rate fixed at 3.6 standard liters per minute. The rotational and vibrational temperatures are simulated from the second positive system of nitrogen, N 2(C3πu-B3πg) , with the rotational temperature being spatially constant at 300 K along the propagation axis of the atmospheric pressure plasma jet while the vibrational temperature is 3620 K at the beginning of the plume and is observed to decrease downstream. The OH(A) emission intensity obtained via optical emission spectroscopy was observed to decrease downstream of the plasma jet. The OH(X) number density along the propagation axis was initially 2.2 × 1013 molecules cm-3 before increasing to a peak value of 2.4 × 1013 molecules cm-3, from which the number density was observed to decrease to 2.2 × 1013 molecules cm-3 downstream of the plasma jet. The total OH(A, X) in the plasma jet remained relatively constant along the propagation axis of the plasma jet before falling off at the tip of the jet. The increase in vibrational temperature downstream and the simultaneous measurements of both the excited state OH(A) and the ground state OH(X) reported in this study provide insights into the formation and consumption of this

  11. Investigation of MHD Instabilities in Jets and Bubbles Using a Compact Coaxial Plasma Gun in a Background Magnetized Plasma

    Science.gov (United States)

    Zhang, Y.; Fisher, D. M.; Wallace, B.; Gilmore, M.; Hsu, S. C.

    2016-10-01

    A compact coaxial plasma gun is employed for experimental investigation of launching plasma into a lower density background magnetized plasma. Experiments are being conducted in the linear device HelCat at UNM. Four distinct operational regimes with qualitatively different dynamics are identified by fast CCD camera images. For regime I plasma jet formation, a global helical magnetic configuration is determined by a B-dot probe array data. Also the m =1 kink instability is observed and verified. Furthermore, when the jet is propagating into background magnetic field, a longer length and lifetime jet is formed. Axial shear flow caused by the background magnetic tension force contributes to the increased stability of the jet body. In regime II, a spheromak-like plasma bubble formation is identified when the gun plasma is injected into vacuum. In contrast, when the bubble propagates into a background magnetic field, the closed magnetic field configuration does not hold anymore and a lateral side, Reilgh-Taylor instability develops. Detailed experimental data and analysis will be presented for these cases.

  12. Technical Summary of the First U.S. Plasma Jet Workshop

    Science.gov (United States)

    Hsu, Scott C.

    2009-09-01

    This paper provides a technical summary of the first U.S. Plasma Jet Workshop, which was sponsored by the DOE Office of Fusion Energy Sciences and held at Los Alamos National Laboratory on January 24-25, 2008. The purpose of the workshop was to bring together members of the national plasma jet research community in order to discuss ongoing research and identify research needs and opportunities in plasma jets and their applications, which include fundamental studies of high energy density (HED) plasmas, magneto-inertial fusion (MIF), laboratory astrophysics, and disruption mitigation and fueling for magnetic confinement devices. Over the course of the workshop, about equal time was devoted to short technical talks and group discussions.

  13. A low power miniaturized dielectric barrier discharge based atmospheric pressure plasma jet

    Science.gov (United States)

    Divya Deepak, G.; Joshi, N. K.; Pal, Dharmendra Kumar; Prakash, Ram

    2017-01-01

    In this paper, a dielectric barrier discharge plasma based atmospheric pressure plasma jet has been generated in a floating helix and floating end ring electrode configuration using argon and helium gases. This configuration is subjected to a range of supply frequencies (10-25 kHz) and supply voltages (2-6 kV) at a fixed rate of gas flow rate (i.e., 1 l/min). The electrical characterization of the plasma jet has been carried out using a high voltage probe and current transformer. The current-voltage characteristics have been analyzed, and the consumed power has been estimated at different applied combinations for optimum power consumption at maximum jet length. The obtained optimum power and jet length for argon and helium gases are 12 mW and 32 mm, and 7.7 mW and 42 mm, respectively. It is inferred that besides the electrode configurations, the discharge gas is also playing a significant role in the low power operation of the cold plasma jet at maximum jet length. The obtained results are interpreted on the basis of penning processes.

  14. Atmospheric pressure He-air plasma jet: Breakdown process and propagation phenomenon

    Energy Technology Data Exchange (ETDEWEB)

    Begum, Asma [Independent University, Bangladesh, School of Engineering and Computer Science, Bashundhara, Dhaka (Bangladesh); Laroussi, Mounir [Old Dominion University, Department of Electrical and Computer Engineering, Norfolk, Virginia (United States); Pervez, Mohammad Rasel [Master Mind College, Department of Physics, Dhanmondi, Dhaka (Bangladesh)

    2013-06-15

    In this paper He-discharge (plasma jet/bullet) in atmospheric pressure air and its progression phenomenon has been studied experimentally using ICCD camera, optical emission spectroscopy (OES) and calibrated dielectric probe measurements. The repetitive nanosecond pulse has applied to a plasma pencil to generate discharge in the helium gas channel. The discharge propagation speed was measured from the ICCD images. The axial electric field distribution in the plasma jet is inferred from the optical emission spectroscopic data and from the probe measurement. The correlation between the jet velocities, jet length with the pulse duration is established. It shows that the plasma jet is not isolated from the input voltage along its propagation path. The discharge propagation speed, the electron density and the local and average electric field distribution along the plasma jet axis predicted from the experimental results are in good agreement with the data predicted by numerical simulation of the streamer propagation presented in different literatures. The ionization phenomenon of the discharge predicts the key ionization parameters, such as speed, peak electric field in the front, and electron density. The maximum local electric field measured by OES is 95 kV/cm at 1.3 cm of the jet axis, and average EF measured by probe is 24 kV/cm at the same place of the jet. The average and local electron density estimated are in the order of 10{sup 11} cm{sup -3} and it reaches to the maximum of 10{sup 12} cm{sup -3}.

  15. Effect of voltage shape of electrical power supply on radiation and density of a cold atmospheric argon plasma jet

    National Research Council Canada - National Science Library

    F Sohbatzadeh; M Bagheri; S Motallebi

    2017-01-01

    In this work, we investigated generating argon cold plasma jet at atmospheric pressure based on dielectric barrier discharge configuration using three electrical power supplies of sinusoidal, pulsed...

  16. Atmospheric pressure plasma jets interacting with liquid covered tissue: touching and not-touching the liquid

    Science.gov (United States)

    Norberg, Seth A.; Tian, Wei; Johnsen, Eric; Kushner, Mark J.

    2014-11-01

    In the use of atmospheric pressure plasma jets in biological applications, the plasma-produced charged and neutral species in the plume of the jet often interact with a thin layer of liquid covering the tissue being treated. The plasma-produced reactivity must then penetrate through the liquid layer to reach the tissue. In this computational investigation, a plasma jet created by a single discharge pulse at three different voltages was directed onto a 200 µm water layer covering tissue followed by a 10 s afterglow. The magnitude of the voltage and its pulse length determined if the ionization wave producing the plasma plume reached the surface of the liquid. When the ionization wave touches the surface, significantly more charged species were created in the water layer with H3O+aq, O3-aq, and O2-aq being the dominant terminal species. More aqueous OHaq, H2O2aq, and O3aq were also formed when the plasma plume touches the surface. The single pulse examined here corresponds to a low repetition rate plasma jet where reactive species would be blown out of the volume between pulses and there is not recirculation of flow or turbulence. For these conditions, NxOy species do not accumulate in the volume. As a result, aqueous nitrites, nitrates, and peroxynitrite, and the HNO3aq and HOONOaq, which trace their origin to solvated NxOy, have low densities.

  17. FAR-TECH's Nanoparticle Plasma Jet System and its Application to Disruptions, Deep Fueling, and Diagnostics

    Science.gov (United States)

    Thompson, J. R.; Bogatu, I. N.; Galkin, S. A.; Kim, J. S.

    2012-10-01

    Hyper-velocity plasma jets have potential applications in tokamaks for disruption mitigation, deep fueling and diagnostics. Pulsed power based solid-state sources and plasma accelerators offer advantages of rapid response and mass delivery at high velocities. Fast response is critical for some disruption mitigation scenario needs, while high velocity is especially important for penetration into tokamak plasma and its confining magnetic field, as in the case of deep fueling. FAR-TECH is developing the capability of producing large-mass hyper-velocity plasma jets. The prototype solid-state source has produced: 1) >8.4 mg of H2 gas only, and 2) >25 mg of H2 and >180 mg of C60 in a H2/C60 gas mixture. Using a coaxial plasma gun coupled to the source, we have successfully demonstrated the acceleration of composite H/C60 plasma jets, with momentum as high as 0.6 g.km/s, and containing an estimated C60 mass of ˜75 mg. We present the status of FAR-TECH's nanoparticle plasma jet system and discuss its application to disruptions, deep fueling, and diagnostics. A new TiH2/C60 solid-state source capable of generating significantly higher quantities of H2 and C60 in <0.5 ms will be discussed.

  18. Numerical study of the interaction of a helium atmospheric pressure plasma jet with a dielectric material

    Science.gov (United States)

    Wang, Lijun; Zheng, Yashuang; Jia, Shenli

    2016-10-01

    This is a computational modeling study of a cold atmospheric pressure helium plasma jet impinging on a dielectric surface placed normal to the jet axis. This study provides insights into the propagation mechanism of the plasma jet, the electrical properties, and the total accumulated charge density at the dielectric surface. For the radial streamer propagation along the dielectric surface, Penning ionization and the electron impact ionization of helium atoms are the major ionization reactions in the streamer head, while Penning ionization is the only dominant contributor along the streamer body. In addition, the plasma bullet velocity along the dielectric surface is 10-100 times lower than that in the plasma column. Increasing tube radius or helium flow rate lowers air entrainment in the plasma jet, leading to a decrease of the radial electric field and the accumulated charge density at the dielectric surface. Furthermore, the tube radius has weaker influence on the plasma properties as tube radius increases. For a target dielectric with lower relative permittivity, a higher radial electric field penetrates into the material, and the surface ionization wave along the dielectric surface extends farther. Higher relative permittivity of the treated dielectric results in more charging at the dielectric surface and more electron density in the plasma column.

  19. Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer.

    Science.gov (United States)

    Babij, Michał; Kowalski, Zbigniew W; Nitsch, Karol; Silberring, Jerzy; Gotszalk, Teodor

    2014-05-01

    The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

  20. Study of an Atmospheric Pressure Plasma Jet of Argon Generated by Column Dielectric Barrier Discharge

    Science.gov (United States)

    Nur, M.; Kinandana, A. W.; Winarto, P.; Muhlisin, Z.; Nasrudin

    2016-11-01

    An atmospheric of argon plasma jet was generated by using column dielectric barrier discharge has been investigated. In this study, argon gas was passed through the capillary column by regulating the flow rate of gas. This atmospheric pressure plasma jet (APPJ) was generated by a sinusoidal AC high voltage in the range of 0.4 kV to 10 kV and at frequencies of 15 kHz and 26 kHz. APPJ has been produced with flow rate of argon gas from 1 litter/min - 10 litters/min. The electric current has been taken with variation of voltage and each interval argon gas flow rate of 1 litter/min. The results show that electric current increase linearly and then it trends to saturation condition by the increasing of applied voltage. We found also that the length of the plasma jet increase by augmenting of applied voltage both for frequencies of 15 kHz and 26 kHz. Furthermore, our results show that length of plasma jet optimum for flow rate of argon gas of 2 litters/minute. In addition, we obtained that the larger applied voltage, the greater the temperature of the plasma jet.

  1. Astrophysics of magnetically collimated jets generated from laser-produced plasmas

    CERN Document Server

    Ciardi, A; Fuchs, J; Albertazzi, B; Riconda, C; Pépin, H; Portugall, O

    2012-01-01

    The generation of astrophysically relevant jets, from magnetically collimated, laser-produced plasmas, is investigated through three-dimensional, magneto-hydrodynamic simulations. We show that for laser intensities I ~ 10^12 - 10^14 W/cm^2, a magnetic field in excess of ~ 0.1 MG, can collimate the plasma plume into a prolate cavity bounded by a shock envelope with a standing conical shock at its tip, which re-collimates the flow into a super magneto-sonic jet beam. This mechanism is equivalent to astrophysical models of hydrodynamic inertial collimation, where an isotropic wind is focused into a jet by a confining circumstellar torus-like envelope. The results suggest an alternative mechanism for a large-scale magnetic field to produce jets from wide-angle winds. (abridged version)

  2. The role of MHD in causing impurity peaking in JET Hybrid plasmas

    CERN Document Server

    Hender, T C; Casson, F J; Alper, B; Baranov, Yu; Baruzzo, M; Challis, C D; Koechl, F; Marchetto, C; Nave, M F F; Pütterich, T; Cortes, S Reyes; Contributors, JET

    2015-01-01

    In Hybrid plasma operation in JET with its ITER-like wall (JET-ILW) it is found that n>1 tearing activity can significantly enhance the rate of on-axis peaking of tungsten impurities, which in turn significantly degrades discharge performance. Core n=1 instabilities can be beneficial in removing tungsten impurities from the plasma core (e.g. sawteeth or fishbones), but can conversely also degrade core confinement (particularly in combination with simultaneous n=3 activity). The nature of MHD instabilities in JET Hybrid discharges, with both its previous Carbon wall and subsequent JET-ILW, is surveyed statistically and the character of the instabilities is examined. Possible qualitative models for how the n>1 islands can enhance on-axis tungsten transport accumulation processes are presented.

  3. Astrophysics of magnetically collimated jets generated from laser-produced plasmas.

    Science.gov (United States)

    Ciardi, A; Vinci, T; Fuchs, J; Albertazzi, B; Riconda, C; Pépin, H; Portugall, O

    2013-01-11

    The generation of astrophysically relevant jets, from magnetically collimated, laser-produced plasmas, is investigated through three-dimensional, magnetohydrodynamic simulations. We show that for laser intensities I∼10(12)-10(14) W cm(-2), a magnetic field in excess of ∼0.1  MG, can collimate the plasma plume into a prolate cavity bounded by a shock envelope with a standing conical shock at its tip, which recollimates the flow into a supermagnetosonic jet beam. This mechanism is equivalent to astrophysical models of hydrodynamic inertial collimation, where an isotropic wind is focused into a jet by a confining circumstellar toruslike envelope. The results suggest an alternative mechanism for a large-scale magnetic field to produce jets from wide-angle winds.

  4. Nanosecond pulsed humid Ar plasma jet in air: shielding, discharge characteristics and atomic hydrogen production

    Science.gov (United States)

    Yatom, Shurik; Luo, Yuchen; Xiong, Qing; Bruggeman, Peter J.

    2017-10-01

    Gas phase non-equilibrium plasmas jets containing water vapor are of growing interest for many applications. In this manuscript, we report a detailed study of an atmospheric pressure nanosecond pulsed Ar  +  0.26% H2O plasma jet. The plasma jet operates in an atmospheric pressure air surrounding but is shielded with a coaxial argon flow to limit the air diffusion into the jet effluent core. The jet impinges on a metal plate electrode and produces a stable plasma filament (transient spark) between the needle electrode in the jet and the metal plate. The stable plasma filament is characterized by spatially and time resolved electrical and optical diagnostics. This includes Rayleigh scattering, Stark broadening of the hydrogen Balmer lines and two-photon absorption laser induced fluorescence (TaLIF) to obtain the gas temperature, the electron density and the atomic hydrogen density respectively. Electron densities and atomic hydrogen densities up to 5 × 1022 m-3 and 2 × 1022 m-3 have been measured. This shows that atomic hydrogen is one of the main species in high density Ar-H2O plasmas. The gas temperature does not exceed 550 K in the core of the plasma. To enable in situ calibration of the H TaLIF at atmospheric pressure a previously published O density calibration scheme is extended to include a correction for the line profiles by including overlap integrals as required by H TaLIF. The line width of H TaLIF, due to collision broadening has the same trend as the neutral density obtained by Rayleigh scattering. This suggests the possibility to use this technique to in situ probe neutral gas densities.

  5. Interaction of in-line twin synthetic jets with a separated flow

    Science.gov (United States)

    Wen, Xin; Tang, Hui; Duan, Fei

    2016-04-01

    An experimental investigation is carried out in a water tunnel to investigate the interaction of in-line twin synthetic jets (SJs) with a separated laminar boundary layer over inclined plates. The flow structures induced by the in-line twin SJs at four phase differences and their resulting flow separation delay are examined using dye visualization and particle image velocimetry (PIV) measurements. It is found that, in most of the cases, the heads of hairpin vortices that are produced from the upstream SJ actuator do not change too much, and the vortex legs are highly stretched by the separated shear layer. An exception is the case with 90° phase difference where the combined vortex head appears as a reversed letter "S" and the combined vortex legs are high enough to escape from the influence of the separated flow. Compared to the single SJ, the twin SJs generally exert greater influence on the separated flow regardless of the phase difference. The PIV results in the mid-span plane reveal that the periodic passage of vortex structures influences the separated flow significantly, causing the flapping of the upper edge of the reversed flow region that contributes to the flow separation delay. The delay of separation is also demonstrated by a streak of forward flow protrusion in the wall-parallel PIV results. It is found that the streak varies a lot at different phase differences. Proper orthogonal decomposition analysis is also conducted and two major types of energetic flow structures in the SJ controlled flow are identified: a strip of back-and-forth fluctuation along the upper edge of the reversed flow, and the vortex structures produced by the twin SJs. It is found that the fluctuation strip is most energetic in the single SJ case and the case with 270° phase difference, whereas the convective mode pair is most energetic in the case with 90° phase difference.

  6. Imaging of the Staphylococcus aureus Inactivation Process Induced by a Multigas Plasma Jet.

    Science.gov (United States)

    Takamatsu, Toshihiro; Kawano, Hiroaki; Sasaki, Yota; Uehara, Kodai; Miyahara, Hidekazu; Matsumura, Yuriko; Iwasawa, Atsuo; Azuma, Takeshi; Okino, Akitoshi

    2016-12-01

    To identify mechanisms underlying the bacterial inactivation process by atmospheric nonthermal plasma using a unique plasma jet that can generate various gas plasmas, Staphylococcus aureus were irradiated with carbon dioxide plasma, which produces a large amount of singlet oxygens, and nitrogen plasma, which produces a large amount of OH radicals. And damaged areas of plasma-treated bacteria were observed by field emission scanning electron microscopy, transmission electron microscopy, and atomic force microscopy. As a result, bacteria were damaged by both gas plasmas, but the site of damage differed according to gas species. Therefore, it suggests that singlet oxygen generated by carbon dioxide plasma or other reactive species caused by singlet oxygen contributes to the damage of internal structures of bacteria through the cell wall and membrane, and OH radicals generated by nitrogen plasma or other reactive species derived from OH radicals contribute to damage of the cell wall and membrane.

  7. Impurity intrusion in radio-frequency micro-plasma jets operated in ambient air

    CERN Document Server

    Niermann, B; Böke, M; Winter, J

    2011-01-01

    Space and time resolved concentrations of helium metastable atoms in an atmospheric pressure radio-frequency micro-plasma jet were measured using tunable diode laser absorption spectroscopy. Spatial profiles as well as lifetime measurements show significant influences of air entering the discharge from the front nozzle and of impurities originating from the gas supply system. Quenching of metastables was used to deduce quantitative concentrations of intruding impurities. The impurity profile along the jet axis was determined from optical emission spectroscopy as well as their dependance on the feed gas flow through the jet.

  8. Characterization of an atmospheric pressure plasma jet and its applications for disinfection and cancer treatment.

    Science.gov (United States)

    Thiyagarajan, Magesh; Sarani, Abdollah; Gonzales, Xavier F

    2013-01-01

    In this work an atmospheric pressure non-thermal resistive barrier (RB) plasma jet was constructed, characterized and was applied for biomedical applications. The RB plasma source can operate in both DC (battery) as well as in standard 60/50 Hz low frequency AC excitation, and it functions effectively in both direct and indirect plasma exposure configurations. The characteristics of the RB plasma jet such as electrical properties, plasma gas temperature and nitric oxides concentration were determined using voltage-current characterization, optical emission spectroscopy and gas analyzer diagnostic techniques. Plasma discharge power of 26.33 W was calculated from voltage-current characterization. An optical emission spectroscopy was applied and the gas temperature which is equivalent to the nitrogen rotational (Trot) temperatures was measured. The concentrations of the reactive oxygen species at different spatial distances from the tip of the plasma jet were measured and the ppm concentration of NO is at the preferred level for a wide range of standard biomedical treatment applications. The ppm values of nitric oxides after the cooling unit are observed to be of the same order of magnitude as compared to plasma jet. The portable RB plasma source was tested to be very effective for decontamination and disinfection of a wide range of foodborne and opportunistic nosocomial pathogens such as Escherichia coli, Staphylococcus aureus, Pseudomonas aeruginosa and Bacillus cereus and the preliminary results are presented. The effects of indirect exposure of the portable RBP source on monocytic leukemia cancer cells (THP-1) were also tested and the results demonstrate that a preference for apoptosis in plasma treated THP-1 cells under particular plasma parameters and dosage levels.

  9. Bimorph-driven synthetic jet actuators optimized for various piezoelectric materials using a low-order model

    Science.gov (United States)

    Yu, Tianliang; Lesieutre, George A.; Griffin, Steven F.; Brzozowski, Daniel P.; Sassoon, Aaron M.

    2017-04-01

    Synthetic jet actuators are of interest for potential applications to active flow control and thermal management. Resonant piezoelectric-diaphragm-type configurations are commonly considered. Modeling of such actuators remains a challenge due to complexities associated with both electro-elastic and fluid-structure coupling, as well as potential non-linearities in both. A key metric for synthetic jet performance is the time-averaged jet momentum. Linear lumped-element modeling is an approach that has demonstrated the ability to predict jet momentum in terms of input frequency and voltage; however, it neglects nonlinearity and increasing losses at high amplitude. Full electro-elastic-fluidic finite element modeling makes the most accurate prediction but is computationally expensive for design and optimization purposes. The assumed-modes method provides an energy-based low-order model which captures electro-elastic and acoustic-structure couplings with adequate accuracy. Tri-laminar circular plates under clamped boundary conditions were modeled using the assumed-modes method. Maximization of jet momentum is considered via the maximization of surrogate device metrics: free volume displacement, effective blocking pressure, strain energy, and device coupling coefficient. The driving frequency of the actuator is treated as a constraint in the optimization which nominally matches the fundamental acoustic natural frequency of the cylindrical cavity. Device configurations were obtained for various polycrystalline and single crystal piezoelectric materials, driven at 10% of their coercive fields in the model. The optimal configurations approximate a simply-supported circular plate with complete piezo coverage. The relative merits of individual materials were also discerned from the optimization results. The low mechanical loss factor of PZT8 enables high output at resonance, while high loss factor and low stiffness limit the utility of PVDF in this application. Due to a

  10. Characteristics of a long and stable filamentary argon plasma jet generated in ambient atmosphere

    Science.gov (United States)

    Teodorescu, M.; Bazavan, M.; Ionita, E. R.; Dinescu, G.

    2015-04-01

    We present a study of a long (up to 60 mm) and thin (600 μm) plasma jet generated at 13.56 MHz in argon expanding in an open atmosphere from inside of a thin glass tube. The discharge is operated with one annular external electrode on the tube, in the absence of any grounded electrode in the discharge proximity. The study comprises image, spectral and electrical measurements, aiming to define and understand the operating domains of this plasma jet source. Two plasma zones were identified, which coexist: a long filament accompanied by a diffuse discharge. The coexistence of these plasma zones was studied in the power-mass flow rate parameter space. An electric model is proposed, considering the jet as a radiating antenna, which allows the determination of the main electrical parameters like capacitance, resistance and active RF power dissipated in the discharge. The specific zones on the I-V characteristics were assigned to the operating domains observed visually. The spectral emission of plasma has been used to characterize the jet in respect to the gas temperature, excitation temperature and plasma density.

  11. Patterned graphene functionalization via mask-free scanning of micro-plasma jet under ambient condition

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Dong; Yu, Yao, E-mail: ensiyu@mail.hust.edu.cn; Liu, Lin [School of Materials Science and Engineering, Huazhong University of Science and Technology, 430074 Wuhan (China); Wu, Shu-Qun; Lu, Xin-Pei [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, 430074 Wuhan (China); Wu, Yue [Department of Physics and Astronomy, University of North Carolina at Chapel Hill, Chapel Hill, North Carolina 27599-3255 (United States)

    2014-03-10

    In this work, a mask-free method is introduced for patterned nitrogen doping of graphene using a micro-plasma jet under ambient condition. Raman and X-ray photoelectron spectroscopy spectra indicate that nitrogen atoms are incorporated into the graphene lattice with the two-dimensional spatial distribution precisely controlled in the range of mm down to 10 μm. Since the chemistry of the micro-plasma jet can be controlled by the choice of the gas mixture, this direct writing process with micro-plasma jet can be a versatile approach for patterned functionalization of graphene with high spatial resolution. This could have promising applications in graphene-based electronics.

  12. Spatially resolved simulation of a radio frequency driven micro atmospheric pressure plasma jet and its effluent

    CERN Document Server

    Hemke, Torben; Gebhardt, Markus; Brinkmann, Ralf Peter; Mussenbrock, Thomas

    2011-01-01

    Radio frequency driven plasma jets are frequently employed as efficient plasma sources for surface modification and other processes at atmospheric pressure. The \\textit{radio-frequency driven micro-scaled atmospheric pressure plasma jet} ($\\mu$APPJ) is a particular variant of that concept whose geometry allows direct optical access. In this work, the characteristics of a $\\mu$APPJ operated with a helium-oxygen mixture and its interaction with a helium environment are studied by numerical simulation. The density and temperature of the electrons, as well as the concentration of all reactive species are studied both in the jet itself and in its effluent. It is found that the effluent is essentially free of charge carriers but contains a substantial amount of activated oxygen (O, O$_3$ and O$_2(^1\\Delta)$).

  13. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device

    Science.gov (United States)

    Whalley, Richard D.; Walsh, James L.

    2016-08-01

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence.

  14. CFD Simulation of a Hydrogen/Argon Plasma Jet Reactor for Coal Pyrolysis

    Institute of Scientific and Technical Information of China (English)

    CHEN H. G.; XIE K. C.

    2004-01-01

    A Computational Fluid Dynamics (CFD) model was formulated for DC arc hydrogen/argon plasma jet reactors used in the process of the thermal H2/Ar plasma pyrolysis of coal to acetylene. In this model, fluid flow, convective heat transfer and conjugate heat conductivity are considered simultaneously. The error caused by estimating the inner-wall temperature of a reactor is avoided. The thermodynamic and transport properties of the hydrogen/argon mixture plasma system, which are usually expressed by a set of discrete dats, are fitted into expressions that can be easily implemented in the program. The effects of the turbulence are modeled by two standard k-s equations. The temperature field and velocity field in the plasma jet reactor were calculated by employing SIMPLEST algorithm. The knowledge and insight obtained are useful for the design improvement and scale-up of plasma reactors.

  15. Turbulent jet flow generated downstream of a low temperature dielectric barrier atmospheric pressure plasma device.

    Science.gov (United States)

    Whalley, Richard D; Walsh, James L

    2016-08-26

    Flowing low temperature atmospheric pressure plasma devices have been used in many technological applications ranging from energy efficient combustion through to wound healing and cancer therapy. The generation of the plasma causes a sudden onset of turbulence in the inhomogeneous axisymmetric jet flow downstream of the plasma plume. The mean turbulent velocity fields are shown to be self-similar and independent of the applied voltage used to generate the plasma. It is proposed that the production of turbulence is related to a combination of the small-amplitude plasma induced body forces and gas heating causing perturbations in the unstable shear layers at the jet exit which grow as they move downstream, creating turbulence.

  16. Analysis of Ar plasma jets induced by single and double dielectric barrier discharges at atmospheric pressure

    Science.gov (United States)

    Judée, F.; Merbahi, N.; Wattieaux, G.; Yousfi, M.

    2016-09-01

    The aim is the comparison of different plasma parameters of single and double dielectric barrier discharge plasma jet configurations (S-DBD and D-DBD) which are potentially usable in biomedical applications. Both configurations are studied in terms of electric field distribution, electrical discharge characteristics, plasma parameters (estimated by optical emission spectroscopy analysis), and hydrodynamics of the plasma jet for electrical parameters of power supplies corresponding to an applied voltage of 10 kV, pulse duration of 1 μs, frequency of 9.69 kHz, and Ar flow of 2 l/min. We observed that the D-DBD configuration requires half the electrical power one needs to provide in the S-DBD case to generate a plasma jet with similar characteristics: excitation temperature around 4700 K, electron density around 2.5 × 1014 cm-3, gas temperature of about 320 K, a relatively high atomic oxygen concentration reaching up to 1000 ppm, the presence of reactive oxygen and nitrogen species (nitric oxide, hydroxyl radical, and atomic oxygen), and an irradiance in the UV-C range of about 20 μW cm-2. Moreover, it has been observed that D-DBD plasma jet is more sensitive to short pulse durations, probably due to the charge accumulation over the dielectric barrier around the internal electrode. This results in a significantly longer plasma length in the D-DBD configuration than in the S-DBD one up to a critical flow rate (2.25 l/min) before the occurrence of turbulence in the D-DBD case. Conversely, ionization wave velocities are significantly higher in the S-DBD setup (3.35 × 105 m/s against 1.02 × 105 m/s for D-DBD), probably due to the higher electrostatic field close to the high voltage electrode in the S-DBD plasma jet.

  17. Experimental characterization of railgun-driven supersonic plasma jets motivated by high energy density physics applications

    CERN Document Server

    Hsu, S C; Moser, A L; Awe, T J; Brockington, S J E; Davis, J S; Adams, C S; Case, A; Cassibry, J T; Dunn, J P; Gilmore, M A; Lynn, A G; Messer, S J; Witherspoon, F D

    2012-01-01

    We report experimental results on the parameters, structure, and evolution of high-Mach-number (M) argon plasma jets formed and launched by a pulsed-power-driven railgun. The nominal initial average jet parameters in the data set analyzed are density \\approx 2 x 10^(16) cm^(-3), electron temperature \\approx 1.4 eV, velocity \\approx 30 km/s, M \\approx 14, ionization fraction \\approx 0.96, diameter \\approx 5 cm, and length \\approx 20 cm. These values approach the range needed by the Plasma Liner Experiment (PLX), which is designed to use merging plasma jets to form imploding spherical plasma liners that can reach peak pressures of 0.1-1 Mbar at stagnation. As these jets propagate a distance of approximately 40 cm, the average density drops by one order of magnitude, which is up to an order of magnitude less than the drop predicted by the ideal hydrodynamic theory of a constant-M jet.

  18. Experimental characterization of railgun-driven supersonic plasma jets motivated by high energy density physics applications

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, S. C.; Moser, A. L.; Awe, T. J.; Davis, J. S.; Dunn, J. P. [Physics Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Merritt, E. C.; Adams, C. S. [Physics Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); University of New Mexico, Albuquerque, New Mexico 87131 (United States); Brockington, S. J. E.; Case, A.; Messer, S. J.; Witherspoon, F. D. [HyperV Technologies Corp., Chantilly, Virginia 20151 (United States); Cassibry, J. T. [Propulsion Research Center, University of Alabama in Huntsville, Huntsville, Alabama 35899 (United States); Gilmore, M. A.; Lynn, A. G. [University of New Mexico, Albuquerque, New Mexico 87131 (United States)

    2012-12-15

    We report experimental results on the parameters, structure, and evolution of high-Mach-number (M) argon plasma jets formed and launched by a pulsed-power-driven railgun. The nominal initial average jet parameters in the data set analyzed are density Almost-Equal-To 2 Multiplication-Sign 10{sup 16} cm{sup -3}, electron temperature Almost-Equal-To 1.4 eV, velocity Almost-Equal-To 30 km/s, M Almost-Equal-To 14, ionization fraction Almost-Equal-To 0.96, diameter Almost-Equal-To 5 cm, and length Almost-Equal-To 20 cm. These values approach the range needed by the Plasma Liner Experiment, which is designed to use merging plasma jets to form imploding spherical plasma liners that can reach peak pressures of 0.1-1 Mbar at stagnation. As these jets propagate a distance of approximately 40 cm, the average density drops by one order of magnitude, which is at the very low end of the 8-160 times drop predicted by ideal hydrodynamic theory of a constant-M jet.

  19. Killing of adherent oral microbes by a non-thermal atmospheric plasma jet.

    Science.gov (United States)

    Rupf, Stefan; Lehmann, Antje; Hannig, Matthias; Schäfer, Barbara; Schubert, Andreas; Feldmann, Uwe; Schindler, Axel

    2010-02-01

    Atmospheric plasma jets are being intensively studied with respect to potential applications in medicine. The aim of this in vitro study was to test a microwave-powered non-thermal atmospheric plasma jet for its antimicrobial efficacy against adherent oral micro-organisms. Agar plates and dentin slices were inoculated with 6 log(10) c.f.u. cm(-2) of Lactobacillus casei, Streptococcus mutans and Candida albicans, with Escherichia coli as a control. Areas of 1 cm(2) on the agar plates or the complete dentin slices were irradiated with a helium plasma jet for 0.3, 0.6 or 0.9 s mm(-2), respectively. The agar plates were incubated at 37 degrees C, and dentin slices were vortexed in liquid media and suspensions were placed on agar plates. The killing efficacy of the plasma jet was assessed by counting the number of c.f.u. on the irradiated areas of the agar plates, as well as by determination of the number of c.f.u. recovered from dentin slices. A microbe-killing effect was found on the irradiated parts of the agar plates for L. casei, S. mutans, C. albicans and E. coli. The plasma-jet treatment reduced the c.f.u. by 3-4 log(10) intervals on the dentin slices in comparison to recovery rates from untreated controls. The microbe-killing effect was correlated with increasing irradiation times. Thus, non-thermal atmospheric plasma jets could be used for the disinfection of dental surfaces.

  20. Monte Carlo study of Quark Gluon Plasma using photon jet observables

    Science.gov (United States)

    Xing, Tian

    2016-09-01

    Relativistic heavy ion collisions create an exotic state of deconfined, nuclear matter called quark gluon plasma (QGP), providing an opportunity to study the strong interaction. In some particularly hard scattered events, a parton with high transverse momentum (pT) interacts with this medium before fragmenting into a spray of particles, called a jet. Jet properties of heavy ion collisions can be modified relative to expectations from pp collisions; this effect is called jet quenching. Measurement of the jet internal structure can provide information about this effect and about the medium itself. On the other hand, studying systems whose jets are recoiled against photons coming from an initial scattering offers a way to calibrate the momentum of the modified jet. Since photons do not carry color charge, they escape the QGP with their initial momentum intact. On this poster, results using the Monte Carlo event generators Pythia and JEWEL will be presented for fragmentation functions and jet suppression from photon-jet events, alongside experimental data from CMS and ATLAS at a center of mass energy of 2.76 TeV. Predictions are also presented for lead-lead collisions at a center of mass energy of 5.02 TeV.

  1. Resummation of Jet Shapes and Extracting Properties of the Quark-Gluon Plasma

    CERN Document Server

    Chien, Yang-Ting

    2014-01-01

    Understanding the properties of the quark-gluon plasma (QGP) that is produced in ultra-relativistic nucleus-nucleus collisions has been one of the top priorities of the heavy ion program at the LHC. Energetic jets are produced and subsequently quenched in the collisions. Such jet quenching phenomena provide promising tools to probe the medium properties by studying the modification of jets due to the medium interactions. Significant modifications of jet shapes have been measured. In this talk we focus on the calculation of jet shapes in both proton-proton and lead-lead collisions using soft-collinear effective theory (SCET), with Glauber gluon interactions in the medium. Large logarithms in jet shapes are resummed at next-to-leading logarithmic (NLL) accuracy by the renormalization-group evolution between hierarchical jet scales. The medium interactions contribute as power corrections, and we calculate the modification of jet shapes at leading order in opacity with the static QGP model. Preliminary results ar...

  2. 3-D MHD modeling and stability analysis of jet and spheromak plasmas launched into a magnetized plasma

    Science.gov (United States)

    Fisher, Dustin; Zhang, Yue; Wallace, Ben; Gilmore, Mark; Manchester, Ward; Arge, C. Nick

    2016-10-01

    The Plasma Bubble Expansion Experiment (PBEX) at the University of New Mexico uses a coaxial plasma gun to launch jet and spheromak magnetic plasma configurations into the Helicon-Cathode (HelCat) plasma device. Plasma structures launched from the gun drag frozen-in magnetic flux into the background magnetic field of the chamber providing a rich set of dynamics to study magnetic turbulence, force-free magnetic spheromaks, and shocks. Preliminary modeling is presented using the highly-developed 3-D, MHD, BATS-R-US code developed at the University of Michigan. BATS-R-US employs an adaptive mesh refinement grid that enables the capture and resolution of shock structures and current sheets, and is particularly suited to model the parameter regime under investigation. CCD images and magnetic field data from the experiment suggest the stabilization of an m =1 kink mode trailing a plasma jet launched into a background magnetic field. Results from a linear stability code investigating the effect of shear-flow as a cause of this stabilization from magnetic tension forces on the jet will be presented. Initial analyses of a possible magnetic Rayleigh Taylor instability seen at the interface between launched spheromaks and their entraining background magnetic field will also be presented. Work supported by the Army Research Office Award No. W911NF1510480.

  3. Optical emission spectroscopy of deuterium and helium plasma jets emitted from plasma focus discharges at the PF-1000U facility

    Science.gov (United States)

    Skladnik-Sadowska, E.; Dan'ko, S. A.; Kwiatkowski, R.; Sadowski, M. J.; Zaloga, D. R.; Paduch, M.; Zielinska, E.; Kharrasov, A. M.; Krauz, V. I.

    2016-12-01

    Optical emission spectroscopy techniques were used to investigate the spectra of dense deuterium-plasma jets generated by high-current pulse discharges within the large PF-1000U facility and to estimate parameters of plasma inside the jets and their surroundings. Time-resolved optical spectra were recorded by means of a Mechelle®900 spectrometer. From an analysis of the deuterium line broadening, it was estimated that the electron concentration at a distance 57 cm from the electrode outlets amounted to (0.4-3.7) × 1017 cm-3 depending on the initial gas distribution and the time interval of the spectrum registration after the instant of the plasma jet generation. From the re-absorption dip in the Dβ profile, it was assessed that the electron concentration in the surrounding gas was equal to about 1.5 × 1015 cm-3. On the basis of the measured ratio of He II 468.6 nm and He I 587.6 nm line intensities, it was estimated that the electron temperature amounted to about 5.3 eV. Also estimated were some dimensionless parameters of the investigated plasma jets.

  4. Generation of intense plasma jets and microparticle beams by an arc in a supersonic vortex

    Science.gov (United States)

    Winterberg, F.

    1990-04-01

    Temperatures up to 50000 have been reached in water vortex stabilized Gerdien arcs. In arcs confined within the cores of supersonic hydrogen vortices much higher temperatures should be possible. Furthermore if these arcs are thermally insulated by a strong magnetic field temperatures up to a 106 K may be attainable. At these temperatures and in passing through a Laval nozzle the arc plasma can reach jet velocities of 100km/sec. If small quantities of heavy elements are entrained by this high velocity plasma jet these heavy elements are carried along reaching the same speed and upon condensation can form beams of clusters and microparticles.

  5. Vehicle implementation of a port injected M100 engine using plasma jet ignition and prompt EGR

    Energy Technology Data Exchange (ETDEWEB)

    Gardiner, D.P.; Mallory, R.W.; Rao, V.K.; Bardon, M.F. [Royal Military Coll. of Canada, Kingston, ON (Canada); Battista, V. [Department of Transport, Ottawa, ON (Canada)

    1994-10-01

    Overhead projection slides used at the 1994 Windsor Workshop on Alternative Fuels describing a port-injected engine using plasma jet ignition and prompt EGR were presented. Benefits of the engine were described, accompanied by technical information of its working concepts. Schematics and a comparison of the plasma jet ignition system with conventional spark plug ignition systems were outlined. Cold starting benefits and ignition hypothesis was summarized. Results of graphical analyses of cold-starting with high and normal cranking speeds were reviewed. 16 figs.

  6. UHV plasma jet system for deposition of magnetic nitride nanocomposite films with GHz applications

    Energy Technology Data Exchange (ETDEWEB)

    Fendrych, F; Lancok, A [Institute of Physics, Academy of Sciences, Na Slovance 2, CZ-18221 Prague 8 (Czech Republic); Repa, P; Peksa, L; Gronych, T; Vejpravova, J P [Faculty of Math and Physics, Charles University in Prague, V Holesovickach 2, CZ-18000 Prague 8 (Czech Republic); Hedbavny, P [VAKUUM PRAHA, V Holesovickach 2, CZ-18000 Prague 8 (Czech Republic); Schaefer, R [Leibniz Institute IFW Dresden, Helmholtzstr. 20, D-01069 Dresden (Germany); Seemann, K M [Forschungszentrum Karlsruhe, Eggenstein, D-76021 Karlsruhe (Germany)], E-mail: fendrych@fzu.cz

    2008-03-15

    A method of preparation of extremely pure magnetic thin films, especially magnetic nitride nanocomposites for GHz aplications was searched. The plasma-jet method was chosen for its advantages at magnetic materials deposition. Sources of impurities deteriorating the quality of the films were analysed. Based on the assumption that the achievable purity is limited mainly by the conditions at the deposition, an experimental UHV apparatus with the plasma-jet was designed. A number of magnetic thin films from various materials including nitride nanocomposite films was prepared already in this apparatus at UHV conditions. Their magnetic properties are far better than those of the films prepared in a high vacuum apparatus.

  7. Nanocapillary Atmospheric Pressure Plasma Jet: A Tool for Ultrafine Maskless Surface Modification at Atmospheric Pressure.

    Science.gov (United States)

    Motrescu, Iuliana; Nagatsu, Masaaki

    2016-05-18

    With respect to microsized surface functionalization techniques we proposed the use of a maskless, versatile, simple tool, represented by a nano- or microcapillary atmospheric pressure plasma jet for producing microsized controlled etching, chemical vapor deposition, and chemical modification patterns on polymeric surfaces. In this work we show the possibility of size-controlled surface amination, and we discuss it as a function of different processing parameters. Moreover, we prove the successful connection of labeled sugar chains on the functionalized microscale patterns, indicating the possibility to use ultrafine capillary atmospheric pressure plasma jets as versatile tools for biosensing, tissue engineering, and related biomedical applications.

  8. Large density amplification measured on jets ejected from a magnetized plasma gun

    OpenAIRE

    Yun, Gunsu S.; You, Setthivoine; Bellan, Paul M.

    2007-01-01

    Observation of a large density amplification in the collimating plasma jet ejected from a coplanar coaxial plasma gun is reported. The jet velocity is ~30 km s^-1 and the electron density increases from ~10^20 to 10^(22–23) m^-3. In previous spheromak experiments, electron density of the order 10^(19–21) m^-3 had been measured in the flux conserver region, but no density measurement had been reported for the source gun region. The coplanar geometry of our electrodes permits direct observation...

  9. Comparison of scrape-off layer transport in inner and outer wall limited JET plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, C., E-mail: csilva@ipfn.ist.utl.pt [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica Lisboa (Portugal); Arnoux, G.; Devaux, S. [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Frigione, D. [Associazione EURATOM-ENEA sulla fusione, CR Frascati, Roma (Italy); Groth, M. [Aalto University, Association EURATOM-Tekes, Otakaari 4, 02015 Espoo (Finland); Horacek, J. [Institute of Plasma Physics AS CR, v.v.i., Association EURATOM/IPP.CR, Praha 8 (Czech Republic); Lomas, P.J. [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Marsen, S. [Max-Planck-Institute for Plasma Physics, EURATOM Association, 17491 Greifswald (Germany); Matthews, G. [Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Pitts, R.A. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

    2013-07-15

    The JET scrape-off layer has been characterized with a reciprocating probe in inner wall, IW, and outer wall, OW, limited plasmas. Broad SOL profiles are observed for IW limited plasmas with power e-folding length substantially larger (by a factor of ∼5–7.5) than in OW limited plasmas. The properties of the fluctuations in the SOL parameters indicate larger turbulent transport for IW limited plasmas. The striking differences observed between IW and OW limited plasmas on the power e-folding length, parallel flow, turbulent transport as well as the characteristics of the fluctuations support the existence of a poloidally localized region of enhanced radial transport near the outboard midplane. The dependence of the SOL power e-folding length on the main plasma parameters was also investigated for IW limited plasmas and a modest negative dependence on both the plasma current and the line-averaged density found.

  10. Atmospheric pressure plasma jet for bacterial decontamination and property improvement of fruit and vegetable processing wastewater

    Science.gov (United States)

    Mohamed, Abdel-Aleam H.; Shariff, Samir M. Al; Ouf, Salama A.; Benghanem, Mohamed

    2016-05-01

    An atmospheric pressure plasma jet was tested for decontaminating and improving the characteristics of wastewater derived from blackberry, date palm, tomato and beetroot processing industries. The jet was generated by blowing argon gas through a cylindrical alumina tube while a high voltage was applied between two electrodes surrounding the tube. Oxygen gas was mixed with argon at the rate of 0.2% and the argon mass flow was fixed at 4.5 slm. Images show that the generated plasma jet penetrated the treated wastewater samples. Plasma emission spectra show the presence of O and OH radicals as well as excited molecular nitrogen and argon. Complete decontamination of wastewater derived from date palm and tomato processing was achieved after 120 and 150 s exposure to the plasma jet, respectively. The bacterial count of wastewater from blackberry and beetroot was reduced by 0.41 and 2.24 log10 colony-forming units (CFU) per ml, respectively, after 180 s. Escherichia coli was the most susceptible bacterial species to the cold plasma while Shigella boydii had the minimum susceptibility, recording 1.30 and 3.34 log10 CFU ml-1, respectively, as compared to the 7.00 log10 initial count. The chemical oxygen demands of wastewater were improved by 57.5-93.3% after 180 s exposure to the plasma jet being tested. The endotoxins in the wastewater were reduced by up to 90.22%. The variation in plasma effectiveness is probably related to the antioxidant concentration of the different investigated wastewaters.

  11. Transfer of a cold atmospheric pressure plasma jet through a long flexible plastic tube

    Science.gov (United States)

    Kostov, Konstantin G.; Machida, Munemasa; Prysiazhnyi, Vadym; Honda, Roberto Y.

    2015-04-01

    This work proposes an experimental configuration for the generation of a cold atmospheric pressure plasma jet at the downstream end of a long flexible plastic tube. The device consists of a cylindrical dielectric chamber where an insulated metal rod that serves as high-voltage electrode is inserted. The chamber is connected to a long (up to 4 m) commercial flexible plastic tube, equipped with a thin floating Cu wire. The wire penetrates a few mm inside the discharge chamber, passes freely (with no special support) along the plastic tube and terminates a few millimeters before the tube end. The system is flushed with Ar and the dielectric barrier discharge (DBD) is ignited inside the dielectric chamber by a low frequency ac power supply. The gas flow is guided by the plastic tube while the metal wire, when in contact with the plasma inside the DBD reactor, acquires plasma potential. There is no discharge inside the plastic tube, however an Ar plasma jet can be extracted from the downstream tube end. The jet obtained by this method is cold enough to be put in direct contact with human skin without an electric shock. Therefore, by using this approach an Ar plasma jet can be generated at the tip of a long plastic tube far from the high-voltage discharge region, which provides the safe operation conditions and device flexibility required for medical treatment.

  12. Propagation of atmospheric pressure helium plasma jet into ambient air at laminar gas flow

    Science.gov (United States)

    Pinchuk, M.; Stepanova, O.; Kurakina, N.; Spodobin, V.

    2017-05-01

    The formation of an atmospheric pressure plasma jet (APPJ) in a gas flow passing through the discharge gap depends on both gas-dynamic properties and electrophysical parameters of the plasma jet generator. The paper presents the results of experimental and numerical study of the propagation of the APPJ in a laminar flow of helium. A dielectric-barrier discharge (DBD) generated inside a quartz tube equipped with a coaxial electrode system, which provided gas passing through it, served as a plasma source. The transition of the laminar regime of gas flow into turbulent one was controlled by the photography of a formed plasma jet. The corresponding gas outlet velocity and Reynolds numbers were revealed experimentally and were used to simulate gas dynamics with OpenFOAM software. The data of the numerical simulation suggest that the length of plasma jet at the unvarying electrophysical parameters of DBD strongly depends on the mole fraction of ambient air in a helium flow, which is established along the direction of gas flow.

  13. [Comparative study on the gas temperature of a plasma jet at atmospheric pressure].

    Science.gov (United States)

    Jia, Peng-Ying; Li, Xue-Chen; Yuan, Ning

    2011-08-01

    A plasma jet of a dielectric barrier discharge in coaxial electrode was used to produce jet plasma in flowing work gas (argon mixed with trace nitrogen) at atmospheric pressure. The relation between the plasma length and the gas flow rate was obtained by taking the images of the jet plasma. A high-resolution optical spectrometer was used to collect the optical emission spectrum. The emission spectra of the first negative band of N(2+) (B2 Sigma(u+)-->Chi2 Sigma(g+), 390-391.6 nm) were used to estimate the rotational temperature of the plasma plume by fitting the experimental spectra to the simulated spectra. The gas temperature was investigated by this optical method and results show that the gas temperature increases with increasing the applied voltage. For comparison, a thermometer was used to measure the temperature of the gas emitted from the jet. The results also show that the gas temperature increases with increasing the applied voltage. The gas temperatures obtained by the two methods are consistent. The difference was analyzed.

  14. Influence of orifice-to-wall distance on synthetic jet vortex ring simpinging on a fixed wall

    Institute of Scientific and Technical Information of China (English)

    XU; Yang; FENG; LiHao

    2013-01-01

    Two-dimensional particle image velocimetry (PIV) is used to investigate the influence of the orifice-to-wall distance on synthetic jet vortex rings impinging on a fixed wall. Both evolutions of vortical structures and statistical characteristics of flow fields at different orifice-to-wall distances are presented. It is found that different orifice-to-wall distances have different effects in terms of the vortex strength and impinging speed when the vortex rings are approaching the wall. The secondary vortex ring can be observed within the shear layer only when the dimensionless orifice-to-wall distance is close to or less than the dimensionless stroke length. Consequently, an appropriate orifice-to-wall distance plays a vital role in the sense of impingement effect. The statistical analysis of the flow field indicates that a wall jet forms after impingement, while both the decay rate of the maximum radial velocity and the spreading rate of the half-width decrease with the increasing orifice-to-wall distance. The non-dimensional wall jet velocity profiles at different orifice-to-wall distances all exhibit self-similar behaviors, which is consistent with the theoretical solution of the laminar wall jet.

  15. Modeling and experimental analysis of phased array synthetic jet cross-flow interactions

    Science.gov (United States)

    Hasnain, Zohaib

    Synthetic Jet Actuators (SJAs) are fluidic devices capable of adding momentum to static or non-static bodies of fluid without adding mass. They are therefore categorized as zero-net-mass-flux (ZNMF) momentum source. In its simplest compact form a SJA consists of an oscillatory surface connected to a cavity with a single exit orifice through which the fluid enters and exits. SJA technology has been utilized in applications ranging from boundary layer control over aerodynamic surfaces to fluidic mixing in dispersion applications. The ZNMF nature of the technology means it is not subject to constraints experienced by traditional momentum sources that require the addition of mass in order to impart momentum. The momentum that can be added by a single SJA is limited by the energy transfer capabilities of the oscillating surface. In modern SJAs this surface usually is a piezoceramic/metal composite subjected to a high voltage AC signal. For applications such as flow control over aerodynamic surfaces, modern SJAs are used in an array configuration and are capable of altering the flow momentum by values ranging from 0.01-10%. While it is possible to build larger actuators to increase this value the benefits associated with the compact size would be lost. It is therefore desirable to tune other parameters associated with SJA arrays to increase this value. The specific motivation for this study comes from the desire to control the momentum addition capacity of a specific SJA array, without having to alter any geometric parameters. In a broader sense this study focuses on understanding the physics of SJA interaction in array configuration through experiments which are then used to guide in the design of modeling technique that predicts SJA array behavior in cross-flows. The first half of the project focused on understanding SJA behavior through modeling. Numerical techniques were initially used to model SJA and SJA arrays in cross-flows. Reduced numerical models were then

  16. Identification of the biologically active liquid chemistry induced by a nonthermal atmospheric pressure plasma jet.

    Science.gov (United States)

    Wende, Kristian; Williams, Paul; Dalluge, Joe; Gaens, Wouter Van; Aboubakr, Hamada; Bischof, John; von Woedtke, Thomas; Goyal, Sagar M; Weltmann, Klaus-Dieter; Bogaerts, Annemie; Masur, Kai; Bruggeman, Peter J

    2015-06-06

    The mechanism of interaction of cold nonequilibrium plasma jets with mammalian cells in physiologic liquid is reported. The major biological active species produced by an argon RF plasma jet responsible for cell viability reduction are analyzed by experimental results obtained through physical, biological, and chemical diagnostics. This is complemented with chemical kinetics modeling of the plasma source to assess the dominant reactive gas phase species. Different plasma chemistries are obtained by changing the feed gas composition of the cold argon based RF plasma jet from argon, humidified argon (0.27%), to argon/oxygen (1%) and argon/air (1%) at constant power. A minimal consensus physiologic liquid was used, providing isotonic and isohydric conditions and nutrients but is devoid of scavengers or serum constituents. While argon and humidified argon plasma led to the creation of hydrogen peroxide dominated action on the mammalian cells, argon-oxygen and argon-air plasma created a very different biological action and was characterized by trace amounts of hydrogen peroxide only. In particular, for the argon-oxygen (1%), the authors observed a strong negative effect on mammalian cell proliferation and metabolism. This effect was distance dependent and showed a half life time of 30 min in a scavenger free physiologic buffer. Neither catalase and mannitol nor superoxide dismutase could rescue the cell proliferation rate. The strong distance dependency of the effect as well as the low water solubility rules out a major role for ozone and singlet oxygen but suggests a dominant role of atomic oxygen. Experimental results suggest that O reacts with chloride, yielding Cl2(-) or ClO(-). These chlorine species have a limited lifetime under physiologic conditions and therefore show a strong time dependent biological activity. The outcomes are compared with an argon MHz plasma jet (kinpen) to assess the differences between these (at least seemingly) similar plasma sources.

  17. Evaluation of the sensitivity of bacterial and yeast cells to cold atmospheric plasma jet treatments.

    Science.gov (United States)

    Sharkey, Michael A; Chebbi, Ahmed; McDonnell, Kevin A; Staunton, Claire; Dowling, Denis P

    2015-06-07

    The focus of this research was first to determine the influence of the atmospheric plasma drive frequency on the generation of atomic oxygen species and its correlation with the reduction of bacterial load after treatment in vitro. The treatments were carried out using a helium-plasma jet source called PlasmaStream™. The susceptibility of multiple microbial cell lines was investigated in order to compare the response of gram-positive and gram-negative bacteria, as well as a yeast cell line to the atmospheric plasma treatment. It was observed for the source evaluated that at a frequency of 160 kHz, increased levels of oxygen-laden active species (i.e., OH, NO) were generated. At this frequency, the maximum level of bacterial inactivation in vitro was also achieved. Ex vivo studies (using freshly excised porcine skin as a human analog) were also carried out to verify the antibacterial effect of the plasma jet treatment at this optimal operational frequency and to investigate the effect of treatment duration on the reduction of bacterial load. The plasma jet treatment was found to yield a 4 log reduction in bacterial load after 6 min of treatment, with no observable adverse effects on the treatment surface. The gram-negative bacterial cell lines were found to be far more susceptible to the atmospheric plasma treatments than the gram-positive bacteria. Flow cytometric analysis of plasma treated bacterial cells (Escherichia coli) was conducted in order to attain a fundamental understanding of the mode of action of the treatment on bacteria at a cellular level. This study showed that after treatment with the plasma jet, E. coli cells progressed through the following steps of cell death; the inactivation of transport systems, followed by depolarization of the cytoplasmic membrane, and finally permeabilization of the cell wall.

  18. Contactless steering of a plasma jet with a 3D magnetic nozzle

    Science.gov (United States)

    Merino, Mario; Ahedo, Eduardo

    2017-09-01

    A 3D, steerable magnetic nozzle (MN) is presented that enables contactless thrust vector control of a plasma jet without any moving parts. The concept represents a substantial simplification over current plasma thruster gimbaled platforms, and requires only a small modification in thrusters that already have a MN. The characteristics of the plasma expansion in the 3D magnetic field and the deflection performance of the device are characterized with a fully magnetized plasma model, suggesting that thrust deflections of 5° -10° are readily achievable.

  19. Bullet-to-streamer transition on the liquid surface of a plasma jet in atmospheric pressure

    Science.gov (United States)

    Yoon, S.-Y.; Kim, G.-H.; Kim, S.-J.; Bae, B.; Kim, N.-K.; Lee, H.; Bae, N.; Ryu, S.; Yoo, S. J.; Kim, S. B.

    2017-01-01

    This study investigated the transition of the plasma shape from a ring-shaped bullet to a pin-like streamer adjacent to the electrolyte surface in a kHz-driven helium atmospheric pressure plasma jet. The transition was observed by synchronized fast images, plasma propagation speed, time-resolved emission profile of Hβ, and spatially and temporally resolved helium metastable density. The transition height increased when electrolyte evaporation was enhanced. The plasma continued to discharge on the electrolyte surface even in the absence of metastable species, i.e., the discharge mechanism changed from Penning ionization between helium metastable and ambient nitrogen to electron collision on evaporated water.

  20. Electron properties and air mixing in radio frequency driven argon plasma jets at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Gessel, Bram van; Bruggeman, Peter [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Brandenburg, Ronny [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Leibniz Institute for Plasma Science and Technology (INP Greifswald), Felix-Hausdorff-Str. 2, D-17489 Greifswald (Germany)

    2013-08-05

    A time modulated radio frequency (RF) plasma jet operated with an Ar mixture is investigated by measuring the electron density and electron temperature using Thomson scattering. The measurements have been performed spatially resolved for two different electrode configurations and as a function of the plasma dissipated power and air concentration admixed to the Ar. Time resolved measurements of electron densities and temperatures during the RF cycle and after plasma power switch-off are presented. Furthermore, the influence of the plasma on the air entrainment into the effluent is studied using Raman scattering.

  1. A model for straight and helical solar jets: II. Parametric study of the plasma beta

    CERN Document Server

    Pariat, E; DeVore, C R; Antiochos, S K; Karpen, J T

    2016-01-01

    Jets are dynamic, impulsive, well-collimated plasma events that develop at many different scales and in different layers of the solar atmosphere. Jets are believed to be induced by magnetic reconnection, a process central to many astrophysical phenomena. Within the solar atmosphere, jet-like events develop in many different environments, e.g., in the vicinity of active regions as well as in coronal holes, and at various scales, from small photospheric spicules to large coronal jets. In all these events, signatures of helical structure and/or twisting/rotating motions are regularly observed. The present study aims to establish that a single model can generally reproduce the observed properties of these jet-like events. In this study, using our state-of-the-art numerical solver ARMS, we present a parametric study of a numerical tridimensional magnetohydrodynamic (MHD) model of solar jet-like events. Within the MHD paradigm, we study the impact of varying the atmospheric plasma $\\beta$ on the generation and prop...

  2. Effect of Pulsed Plasma Jets on the Recovering Boundary Layer Downstream of a Reflected Shock Interaction

    Science.gov (United States)

    Greene, Benton; Clemens, Noel; Magari, Patrick; Micka, Daniel; Ueckermann, Mattheus

    2015-11-01

    Shock-induced turbulent boundary layer separation can have many detrimental effects in supersonic inlets including flow distortion and instability, structural fatigue, poor pressure recovery, and unstart. The current study investigates the effect of pulsed plasma jets on the recovering boundary layer downstream of a reflected shock wave-boundary layer interaction. The effects of pitch and skew angle of the jet as well as the heating parameter and discharge time scale are tested using several pulsing frequencies. In addition, the effect of the plasma jets on the undisturbed boundary layer at 6 mm and 11 mm downstream of the jets is measured. A pitot-static pressure probe is used to measure the velocity profile of the boundary layer 35 mm downstream of the plasma jets, and the degree of boundary layer distortion is compared between the different models and run conditions. Additionally, the effect of each actuator configuration on the shape of the mean separated region is investigated using surface oil flow visualization. Previous studies with lower energy showed a weak effect on the downstream boundary layer. The current investigation will attempt to increase this effect using a higher-energy discharge. Funded by AFRL through and SBIR in collaboration with Creare, LLC.

  3. Exciting gauge unstable modes of the quark-gluon plasma by relativistic jets

    Energy Technology Data Exchange (ETDEWEB)

    Mannarelli, M; Manuel, C [Instituto de Ciencias del Espacio (IEEC/CSIC), Campus Universitat Autonoma de Barcelona, Facultat de Ciencies, Torre C5 E-08193 Bellaterra (Barcelona) (Spain)], E-mail: massimo@ieec.uab.es

    2008-05-15

    We present a study of the properties of the collective modes of a system composed by a thermalized quark-gluon plasma traversed by a relativistic jet of partons. We find that when the jet traverses the system unstable gauge field modes are excited and grow on very short time scales. The aim is to provide a novel mechanism for the description of the jet quenching phenomenon, where the jet crossing the plasma loses energy exciting colored unstable modes. In order to simplify the analysis we employ a linear response approximation, valid for short time scales. We assume that the partons in the jet can be described with a tsunami-like distribution function, whereas we treat the quark-gluon plasma employing two different approaches. In the first approach we adopt a Vlasov approximation for the kinetic equations, in the second approach we solve a set of fluid equations. In both cases we derive the expressions of the dispersion law of the collective unstable modes and compare the results obtained.

  4. Effect of cold atmospheric pressure He-plasma jet on DNA change and mutation

    Energy Technology Data Exchange (ETDEWEB)

    Yaopromsiri, C. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand); Sarapirom, S. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Faculty of Science, Maejo University, Bang Khen, Chiang Mai 50290 (Thailand); Thopan, P.; Boonyawan, D. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

    2015-12-15

    Cold atmospheric pressure plasma jet (CAPPJ) effect on DNA change was studied for assessment of its safety. The experiment utilized a home-developed CAPPJ using 100% helium to directly treat naked DNA plasmid pGFP (plasmid green fluorescent protein). A traversal electric field was applied to separate the plasma components and both dry and wet sample conditions were adopted to investigate various factor roles in changing DNA. Plasma species were measured by using optical emission spectroscopy. DNA topological form change was analyzed by gel electrophoresis. The plasma jet treated DNA was transferred into bacterial Escherichia coli cells for observing mutation. The results show that the He-CAPPJ could break DNA strands due to actions from charge, radicals and neutrals and potentially cause genetic modification of living cells.

  5. Effect of cold atmospheric pressure He-plasma jet on DNA change and mutation

    Science.gov (United States)

    Yaopromsiri, C.; Yu, L. D.; Sarapirom, S.; Thopan, P.; Boonyawan, D.

    2015-12-01

    Cold atmospheric pressure plasma jet (CAPPJ) effect on DNA change was studied for assessment of its safety. The experiment utilized a home-developed CAPPJ using 100% helium to directly treat naked DNA plasmid pGFP (plasmid green fluorescent protein). A traversal electric field was applied to separate the plasma components and both dry and wet sample conditions were adopted to investigate various factor roles in changing DNA. Plasma species were measured by using optical emission spectroscopy. DNA topological form change was analyzed by gel electrophoresis. The plasma jet treated DNA was transferred into bacterial Escherichia coli cells for observing mutation. The results show that the He-CAPPJ could break DNA strands due to actions from charge, radicals and neutrals and potentially cause genetic modification of living cells.

  6. 3D Kinetic Simulation of Plasma Jet Penetration in Magnetic Field

    Science.gov (United States)

    Galkin, Sergei A.; Bogatu, I. N.; Kim, J. S.

    2009-11-01

    A high velocity plasmoid penetration through a magnetic barrier is a problem of a great experimental and theoretical interest. Our LSP PIC code 3D fully kinetic numerical simulations of high density (10^16 cm-3) high velocity (30-140 km/sec) plasma jet/bullet, penetrating through the transversal magnetic field, demonstrate three different regimes: reflection by field, penetration by magnetic field expulsion and penetration by magnetic self-polarization. The behavior depends on plasma jet parameters and its composition: hydrogen, carbon (A=12) and C60-fullerene (A=720) plasmas were investigated. The 3D simulation of two plasmoid head-on injections along uniform magnetic field lines is analyzed. Mini rail plasma gun (accelerator) modeling is also presented and discussed.

  7. Ion acceleration and plasma jet formation in ultra-thin foils undergoing expansion and relativistic transparency

    Energy Technology Data Exchange (ETDEWEB)

    King, M.; Gray, R.J.; Powell, H.W.; MacLellan, D.A.; Gonzalez-Izquierdo, B. [SUPA Department of Physics, University of Strathclyde, Glasgow G4 0NG (United Kingdom); Stockhausen, L.C. [Centro de Laseres Pulsados (CLPU), Parque Cientifico, Calle del Adaja, s/n. 37185 Villamayor, Salamanca (Spain); Hicks, G.S.; Dover, N.P. [The John Adams Institute for Accelerator Science, Blackett Laboratory, Imperial College London, London SW7 2BZ (United Kingdom); Rusby, D.R. [SUPA Department of Physics, University of Strathclyde, Glasgow G4 0NG (United Kingdom); Central Laser Facility, STFC Rutherford Appleton Laboratory, Oxfordshire OX11 0QX (United Kingdom); Carroll, D.C. [Central Laser Facility, STFC Rutherford Appleton Laboratory, Oxfordshire OX11 0QX (United Kingdom); Padda, H. [SUPA Department of Physics, University of Strathclyde, Glasgow G4 0NG (United Kingdom); Torres, R. [Centro de Laseres Pulsados (CLPU), Parque Cientifico, Calle del Adaja, s/n. 37185 Villamayor, Salamanca (Spain); Kar, S. [Centre for Plasma Physics, Queens University Belfast, Belfast BT7 1NN (United Kingdom); Clarke, R.J.; Musgrave, I.O. [Central Laser Facility, STFC Rutherford Appleton Laboratory, Oxfordshire OX11 0QX (United Kingdom); Najmudin, Z. [The John Adams Institute for Accelerator Science, Blackett Laboratory, Imperial College London, London SW7 2BZ (United Kingdom); Borghesi, M. [Centre for Plasma Physics, Queens University Belfast, Belfast BT7 1NN (United Kingdom); Neely, D. [Central Laser Facility, STFC Rutherford Appleton Laboratory, Oxfordshire OX11 0QX (United Kingdom); McKenna, P., E-mail: paul.mckenna@strath.ac.uk [SUPA Department of Physics, University of Strathclyde, Glasgow G4 0NG (United Kingdom)

    2016-09-01

    At sufficiently high laser intensities, the rapid heating to relativistic velocities and resulting decompression of plasma electrons in an ultra-thin target foil can result in the target becoming relativistically transparent to the laser light during the interaction. Ion acceleration in this regime is strongly affected by the transition from an opaque to a relativistically transparent plasma. By spatially resolving the laser-accelerated proton beam at near-normal laser incidence and at an incidence angle of 30°, we identify characteristic features both experimentally and in particle-in-cell simulations which are consistent with the onset of three distinct ion acceleration mechanisms: sheath acceleration; radiation pressure acceleration; and transparency-enhanced acceleration. The latter mechanism occurs late in the interaction and is mediated by the formation of a plasma jet extending into the expanding ion population. The effect of laser incident angle on the plasma jet is explored.

  8. Advances in physical study of high enthalpy plasma jets of technological interest: emission spectra and plasma characteristics

    Science.gov (United States)

    Belevtsev, A. A.; Chinnov, V. F.; Isakaev, E. Kh.; Markin, A. V.; Tazikova, T. F.; Tereshkin, S. A.

    1998-10-01

    Offers a comprehensive study of the emission spectra and plasma characteristics of high enthalpy atmospheric pressure argon and nitrogen jets produced by a high- current industrially important arc plasmatron with a vortex stabilized channel-anode (I4g/s, jet diameter at a minimum-6mm). The spectra are taken at different distances from the cathode in the 200-950nm region with a spectral resolution=3D0.01nm allowing a fine structure of vibronic bands to be essentially resolved except that due to the dublet (spin) splitting and Λ-doubling. Also derived (through the Abel inversion) are radial distributions of plasma components. The spectra obtained have been used for determining plasma composition, the electron component parameters (by atomic/ionic Stark half-widths and intensities) and the assessment of rotational and vibrational temperatures by simulating molecular bands.

  9. Analysis of Kelvin Helmholtz Instabilities of Plasma Jets

    Science.gov (United States)

    Friedman, Mark J.; Hollingsworth, Blane J.

    1999-01-01

    Ulysses data indicates density fluctuations which are theorized to be the result of shear between a solar jet and its ambient. The MHD Kelvin-Helmholtz ("KH") instability causes such fluctuations as observed by Ulysses. A new dispersion relationship which accounts for this KH instability is derived via the linearization of the MHD equations. This generalizes an earlier result by Hardee. This dispersion relationship has the form of eight non-linear equations with nine unknowns.

  10. Generation of Cold Argon Plasma Jet at the End of Flexible Plastic Tube

    CERN Document Server

    Kostov, Konstantin G; Prysiazhnyi, Vadym

    2014-01-01

    This brief communication reports a new method for generation of cold atmospheric pressure plasma jet at the downstream end of a flexible plastic tube. The device consists of a small chamber where dielectric barrier discharge (DBD) is ignited in Argon. The discharge is driven by a conventional low frequency AC power supply. The exit of DBD reactor is connected to a commercial flexible plastic tube (up to 4 meters long) with a thin floating Cu wire inside. Under certain conditions an Ar plasma jet can be extracted from the downstream tube end and there is no discharge inside the plastic tube. The jet obtained by this method is cold enough to be put in direct contact with human skin without electric shock and can be used for medical treatment and decontamination.

  11. Cold atmospheric plasma jet-generated RONS and their selective effects on normal and carcinoma cells.

    Science.gov (United States)

    Kim, Sun Ja; Chung, T H

    2016-02-03

    Cold atmospheric helium plasma jets were fabricated and utilized for plasma-cell interactions. The effect of operating parameters and jet design on the generation of specific reactive oxygen and nitrogen species (RONS) within cells and cellular response were investigated. It was found that plasma treatment induced the overproduction of RONS in various cancer cell lines selectively. The plasma under a relatively low applied voltage induced the detachment of cells, a reduction in cell viability, and apoptosis, while the plasma under higher applied voltage led to cellular necrosis in our case. To determine whether plasma-induced reactive oxygen species (ROS) generation occurs through interfering with mitochondria-related cellular response, we examined the plasma effects on ROS generation in both parental A549 cells and A549 ρ(0) cells. It was observed that cancer cells were more susceptible to plasma-induced RONS (especially nitric oxide (NO) and nitrogen dioxide (NO2(-)) radicals) than normal cells, and consequently, plasma induced apoptotic cell responses mainly in cancer cells.

  12. Effects of atmospheric pressure plasma jet with floating electrode on murine melanoma and fibroblast cells

    Science.gov (United States)

    Xu, G.; Liu, J.; Yao, C.; Chen, S.; Lin, F.; Li, P.; Shi, X.; Zhang, Guan-Jun

    2017-08-01

    Atmospheric pressure cold plasma jets have been recently shown as a highly promising tool in certain cancer therapies. In this paper, an atmospheric pressure plasma jet (APPJ) with a one inner floating and two outer electrode configuration using helium gas for medical applications is developed. Subjected to a range of applied voltages with a frequency of 19.8 kHz at a fixed rate of gas flow (i.e., 3 l/min), electrical and optical characteristics of the APPJ are investigated. Compared with the device only with two outer electrodes, higher discharge current, longer jet, and more active species in the plasma plume at the same applied voltage together with the lower gas breakdown voltage can be achieved through embedding a floating inner electrode. Employing the APPJ with a floating electrode, the effects of identical plasma treatment time durations on murine melanoma cancer and normal fibroblast cells cultured in vitro are evaluated. The results of cell viability, cell apoptosis, and DNA damage detection show that the plasma can inactivate melanoma cells in a time-dependent manner from 10 s to 60 s compared with the control group (p melanoma cells at the same treatment time. The different basal reactive oxygen species level and antioxidant superoxide dismutase level of two kinds of cells may account for their different responses towards the identical plasma exposure.

  13. Cold atmospheric plasma jet effects on V79-4 cells.

    Science.gov (United States)

    Lupu, Andreea-Roxana; Georgescu, N

    2010-01-01

    The effects of cold plasmas are due to charged particles, reactive oxygen species (ROS), reactive nitrogen species (RNS), UV photons, and intense electric field. In order to obtain a more efficient action on mammalian cells (useful for cancer therapy), we used in our studies chemically activated cold plasma (He and O2 gas mixture). V79-4 cells were exposed to plasma jet for different time periods (30, 60, 90, 120 and 150s), using different combinations of helium and oxygen inputs (He:2.5l/min + 02:12.5ml/min; He:2.51/min + O2:25ml/min; He:2.51/min + O2:37.5 ml/min). Using MTT test we demonstrated that plasma jet induced cell viability decrease in all cases. The effect of chemically activated cold plasma--apoptosis or necrosis--depends on gas mixture and treatment period. Taking into account that ROS density in cell microenvironment is related to O2 percent in the gas mixture and treatment period, we can presume that cell death is due to ROS produced in plasma jet.

  14. Reduction and degradation of amyloid aggregates by a pulsed radio-frequency cold atmospheric plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Bayliss, D L; Walsh, J L; Iza, F; Kong, M G [Department of Electronic and Electrical Engineering, Loughborough University, Leicestershire LE11 3TU (United Kingdom); Shama, G [Department of Chemical Engineering, Loughborough University, Leicestershire LE11 3TU (United Kingdom)], E-mail: m.g.kong@lboro.ac.uk

    2009-11-15

    Surface-borne amyloid aggregates with mature fibrils are used as a non-infectious prion model to evaluate cold atmospheric plasmas (CAPs) as a prion inactivation strategy. Using a helium-oxygen CAP jet with pulsed radio-frequency (RF) excitation, amyloid aggregates deposited on freshly cleaved mica discs are reduced substantially leaving only a few spherical fragments of sub-micrometer sizes in areas directly treated by the CAP jet. Outside the light-emitting part of the CAP jet, plasma treatment results in a 'skeleton' of much reduced amyloid stacks with clear evidence of fibril fragmentation. Analysis of possible plasma species and the physical configuration of the jet-sample interaction suggests that the skeleton structures observed are unlikely to have arisen as a result of physical forces of detachment, but instead by progressive diffusion of oxidizing plasma species into porous amyloid aggregates. Composition of chemical bonds of this reduced amyloid sample is very different from that of intact amyloid aggregates. These suggest the possibility of on-site degradation by CAP treatment with little possibility of spreading contamination elsewhere , thus offering a new reaction chemistry route to protein infectivity control with desirable implications for the practical implementation of CAP-based sterilization systems.

  15. Reduction and degradation of amyloid aggregates by a pulsed radio-frequency cold atmospheric plasma jet

    Science.gov (United States)

    Bayliss, D. L.; Walsh, J. L.; Shama, G.; Iza, F.; Kong, M. G.

    2009-11-01

    Surface-borne amyloid aggregates with mature fibrils are used as a non-infectious prion model to evaluate cold atmospheric plasmas (CAPs) as a prion inactivation strategy. Using a helium-oxygen CAP jet with pulsed radio-frequency (RF) excitation, amyloid aggregates deposited on freshly cleaved mica discs are reduced substantially leaving only a few spherical fragments of sub-micrometer sizes in areas directly treated by the CAP jet. Outside the light-emitting part of the CAP jet, plasma treatment results in a 'skeleton' of much reduced amyloid stacks with clear evidence of fibril fragmentation. Analysis of possible plasma species and the physical configuration of the jet-sample interaction suggests that the skeleton structures observed are unlikely to have arisen as a result of physical forces of detachment, but instead by progressive diffusion of oxidizing plasma species into porous amyloid aggregates. Composition of chemical bonds of this reduced amyloid sample is very different from that of intact amyloid aggregates. These suggest the possibility of on-site degradation by CAP treatment with little possibility of spreading contamination elsewhere , thus offering a new reaction chemistry route to protein infectivity control with desirable implications for the practical implementation of CAP-based sterilization systems.

  16. Large-scale drifts observed on electron temperature measurements on JET plasmas

    CERN Document Server

    Gerbaud, Thomas; Alper, Barry; Beausang, Kieran; Beurskens, Marc; Flanagan, Joanne; Kempenaars, Mark; Sirinelli, Antoine; Maslov, Mikhail; Dif-Pradalier, Guilhem; Contributors, JET EFDA

    2012-01-01

    Between 1995 and 2009, electron temperature (Te) measurements of more than 15000 plasmas produced in the Joint European Torus (JET) have been carefully reviewed using the two main diagnostics available over this time period: Michelson interferometer and Thomson scattering systems. Long term stability of JET Te is experimentaly observed by defining the ECE TS ratio as the ratio of central Te measured by Michelson and LIDAR. This paper, based on a careful review of Te measurement from 15 years of JET plasmas, concludes that JET Te exhibits a 15-20% effective uncertainty mostly made of large-scale temporal drifts, and an overall uncertainty of 16-22%. Variations of 18 plasma parameters are checked in another data set, made of a "reference data set" made of ohmic pulses as similar as possible between 1998 and 2009. Time drifts of ECE TS ratios appear to be mostly disconnected from the variations observed on these 18 plasma parameters, except for the very low amplitude variations of the field which are well correl...

  17. The role of VUV radiation in the inactivation of bacteria with an atmospheric pressure plasma jet

    CERN Document Server

    Schneider, Simon; Ellerweg, Dirk; Denis, Benjamin; Narberhaus, Franz; Bandow, Julia E; Benedikt, Jan

    2011-01-01

    A modified version of a micro scale atmospheric pressure plasma jet (\\mu-APPJ) source, so-called X-Jet, is used to study the role of plasma generated VUV photons in the inactivation of E. coli bacteria. The plasma is operated in He gas or a He/O2 mixture and the X-Jet modification of the jet geometry allows effective separation of heavy reactive particles (such as O atoms or ozone molecules) from the plasma-generated photons. The measurements of the evolution of zone of inhibitions formed in monolayers of vegetative E. coli bacteria, of VUV emission intensity and of positive ion spectra show that photochemistry in the gas phase followed by photochemistry products impacting on bacteria can result in bacterial inactivation. Interestingly, this process is more effective than direct inactivation by VUV radiation damage. Mainly protonated water cluster ions are detected by mass spectrometry indicating that water impurity has to be carefully considered. The measurements indicate that the combination of the presence...

  18. Study on coal pyrolysis in Ar/H{sub 2} plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Chen, H.G.; Tian, Y.J.; Li, F.; Zhu, S.Y.; Xie, K.C. [Taiyuan University of Technology, Taiyuan (China). Shanxi Key Lab of Coal Science and Technology

    1999-07-01

    Hydrogen/Ar plasma jet was used to convert coal into acetylene. The efficiency of conversion depended on factors such as size range of coal particles, volatile matter and operating conditions. Coals had different acetylene selectivity which may depend on coal structure. 5 refs., 3 tabs.

  19. Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

    Science.gov (United States)

    Kan, C. W.; Kwong, C. H.; Ng, S. P.

    2015-08-01

    Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment.

  20. A numerical study of plasma detachment conditions in JET divertor plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Simonini, R.; Corrigan, G.; Radford, G.; Spence, J.; Taroni, A.; Weber, S. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking

    1994-07-01

    Simulation results obtained with the EDGE2D/U code confirm that for a given particle inventory in the SOL (including the divertor), the main parameter determining whether or not particle, momentum and energy detachment occurs, is the residual power P - P{sub lost}, where P is the total power entering the SOL and P{sub lost} is the power lost by transport to walls and by volume losses in the SOL outside the region where detachment takes place. For particle contents leading to reasonable values of the separatrix mid-plane density, detachment is found if the residual power is low enough. Typically the residual power must be inferior to 3 MW for good detachment, with the exact value depending on the geometry of the divertor, the transport assumptions and the neutral recirculation scheme. The results show that divertor plasma conditions relevant for the study of power exhaust and impurity control problems are possible in JET. 9 refs., 2 figs., 1 tab.

  1. Comparison of the characteristics of atmospheric pressure plasma jets using different working gases and applications to plasma-cancer cell interactions

    Directory of Open Access Journals (Sweden)

    Hea Min Joh

    2013-09-01

    Full Text Available Atmospheric pressure plasma jets employing nitrogen, helium, or argon gases driven by low-frequency (several tens of kilohertz ac voltage and pulsed dc voltage were fabricated and characterized. The changes in discharge current, optical emission intensities from reactive radicals, gas temperature, and plume length of plasma jets with the control parameters were measured and compared. The control parameters include applied voltage, working gas, and gas flow rate. As an application to plasma-cancer cell interactions, the effects of atmospheric pressure plasma jet on the morphology and intracellular reactive oxygen species (ROS level of human lung adenocarcinoma cell (A549 and human bladder cancer cell (EJ were explored. The experimental results show that the plasma can effectively control the intracellular concentrations of ROS. Although there exist slight differences in the production of ROS, helium, argon, or nitrogen plasma jets are found to be useful in enhancing the intracellular ROS concentrations in cancer cells.

  2. Pulsed microwave-driven argon plasma jet with distinctive plume patterns resonantly excited by surface plasmon polaritons

    Institute of Scientific and Technical Information of China (English)

    陈兆权; 殷志祥; 夏广庆; 洪伶俐; 胡业林; 刘明海; 胡希伟

    2015-01-01

    Atmospheric lower-power pulsed microwave argon cold plasma jets are obtained by using coaxial transmission line resonators in ambient air. The plasma jet plumes are generated at the end of a metal wire placed in the middle of the dielec-tric tubes. The electromagnetic model analyses and simulation results suggest that the discharges are excited resonantly by the enhanced electric field of surface plasmon polaritons. Moreover, for conquering the defect of atmospheric argon filamentation discharges excited by 2.45-GHz continued microwave, the distinctive patterns of the plasma jet plumes can be maintained by applying different gas flow rates of argon gas, frequencies of pulsed modulator, duty cycles of pulsed microwave, peak values of input microwave power, and even by using different materials of dielectric tubes. In addition, the emission spectrum, the plume temperature, and other plasma parameters are measured, which shows that the proposed pulsed microwave plasma jets can be adjusted for plasma biomedical applications.

  3. Rare gas flow structuration in plasma jet experiments

    Science.gov (United States)

    Robert, E.; Sarron, V.; Darny, T.; Riès, D.; Dozias, S.; Fontane, J.; Joly, L.; Pouvesle, J.-M.

    2014-02-01

    Modifications of rare gas flow by plasma generated with a plasma gun (PG) are evidenced through simultaneous time-resolved ICCD imaging and schlieren visualization. The geometrical features of the capillary inside which plasma propagates before in-air expansion, the pulse repetition rate and the presence of a metallic target are playing a key role on the rare gas flow at the outlet of the capillary when the plasma is switched on. In addition to the previously reported upstream offset of the laminar to turbulent transition, we document the reverse action leading to the generation of long plumes at moderate gas flow rates together with the channeling of helium flow under various discharge conditions. For higher gas flow rates, in the l min-1 range, time-resolved diagnostics performed during the first tens of ms after the PG is turned on, evidence that the plasma plume does not start expanding in a laminar neutral gas flow. Instead, plasma ignition leads to a gradual laminar-like flow build-up inside which the plasma plume is generated. The impact of such phenomena for gas delivery on targets mimicking biological samples is emphasized, as well as their consequences on the production and diagnostics of reactive species.

  4. Plasma-Jet-Driven Magneto-Inertial Fusion (PJMIF): Physics and Design for a Plasma Liner Formation Experiment

    Science.gov (United States)

    Hsu, Scott; Cassibry, Jason; Witherspoon, F. Douglas

    2014-10-01

    Spherically imploding plasma liners are a potential standoff compression driver for magneto-inertial fusion, which is a hybrid of and operates in an intermediate density between those of magnetic and inertial fusion. We propose to use an array of merging supersonic plasma jets to form a spherically imploding plasma liner. The jets are to be formed by pulsed coaxial guns with contoured electrodes that are placed sufficiently far from the location of target compression such that no hardware is repetitively destroyed. As such, the repetition rate can be higher (e.g., 1 Hz) and ultimately the power-plant economics can be more attractive than most other MIF approaches. During the R&D phase, a high experimental shot rate at reasonably low cost (e.g., gun plasma-liner-formation experiment, which will provide experimental data on: (i) scaling of peak liner ram pressure versus initial jet parameters, (ii) liner non-uniformity characterization and control, and (iii) control of liner profiles for eventual gain optimization.

  5. Formation of NOx precursors during Chinese pulverized coal pyrolysis in an arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Wei-ren Bao; Jin-cao Zhang; Fan Li; Li-ping Chang [Taiyuan University of Technology, Taiyuan (China). Key Laboratory of Coal Science and Technology

    2007-08-15

    The formation of NOx precursors (HCN and NH{sub 3}) from the pyrolysis of several Chinese pulverized coals in an arc plasma jet was investigated through both thermodynamic analysis of the C-H-O-N system and experiments. Results of thermodynamic analysis show that the dominant N-containing gaseous species is HCN together with a small amount of ammonia above the temperature of 2000 K. The increase of H content advances the formation of HCN and NH{sub 3}, but the yields of HCN and NH{sub 3} are decreased with a high concentration of O in the system. These results are accordant with the experimental data. The increasing of input power promotes the formation of HCN and NH{sub 3} from coal pyrolysis in an arc plasma jet. Tar-N is not formed during the process. The yield of HCN changes insignificantly with the changing of the residence time of coal particles in the reactor, but that of NH{sub 3} decreases as residence times increase because of the relative instability at high temperature. Adsorption and gasification of CO{sub 2} on the coal surface also can restrain the formation of HCN and NH{sub 3} compare to the results in an Ar plasma jet. Yields of HCN and NH{sub 3} are sensitive to the coal feeding rate, indicating that NOx precursors could interact with the nascent char to form other N-containing species. The formation of HCN and NH{sub 3} during coal pyrolysis in a H{sub 2}/Ar plasma jet are not dependent on coal rank. The N-containing gaseous species is released faster than others in the volatiles during coal pyrolysis in an arc plasma jet, and the final nitrogen content in the char is lower than that in the parent coal, which it is independent of coal type. 16 refs., 9 figs., 1 tab.

  6. Characterizations of atmospheric pressure low temperature plasma jets and their applications

    Science.gov (United States)

    Karakas, Erdinc

    2011-12-01

    Atmospheric pressure low temperature plasma jets (APLTPJs) driven by short pulses have recently received great attention because of their potential in biomedical and environmental applications. This potential is due to their user-friendly features, such as low temperature, low risk of arcing, operation at atmospheric pressure, easy handheld operation, and low concentration of ozone generation. Recent experimental observations indicate that an ionization wave exists and propagates along the plasma jet. The plasma jet created by this ionization wave is not a continuous medium but rather consists of a bullet-like-structure known as "Plasma Bullet". More interestingly, these plasma bullets actually have a donut-shaped makeup. The nature of the plasma bullet is especially interesting because it propagates in the ambient air at supersonic velocities without any externally applied electric field. In this dissertation, experimental insights are reported regarding the physical and chemical characteristics of the APLTPJs. The dynamics of the plasma bullet are investigated by means of a high-speed ICCD camera. A plasma bullet propagation model based on the streamer theory is confirmed with adequate explanations. It is also found that a secondary discharge, ignited by the charge accumulation on the dielectric electrode surfaces at the end of the applied voltage, interrupts the plasma bullet propagation due to an opposing current along the ionization channel. The reason for this interesting phenomenon is explained in detail. The plasma bullet comes to an end when the helium mole fraction along the ionization channel, or applied voltage, or both, are less than some critical values. The presence of an inert gas channel in the surrounding air, such as helium or argon, has a critical role in plasma bullet formation and propagation. For this reason, a fluid dynamics study is employed by a commercially available simulation software, COMSOL, based on finite element method. Spatio

  7. Convection-Diffusion Model for Atmospheric Pressure Plasma Jets: Obtaining Off-Axis Data from On-Axis Measurements

    Science.gov (United States)

    Schmidt-Bleker, Ansgar; Dünnbier, Mario; Winter, Jörn; Weltmann, Klaus-Dieter; Reuter, Stephan

    2012-10-01

    An analytical convection-diffusion model for atmospheric pressure plasma jets is presented. The model can be applied both for ambient air species diffusion and for heat transfer into a jets effluent. Using on-axis data from experiments as input, the model can be used to extrapolate the measured quantities to the complete domain for laminar flows and near-axis region for turbulent flows. The method is applied to experimental data obtained from molecular beam mass spectrometry as well as from a VUV absorption spectrometry method using the plasma jet itself as a VUV emitter. The measurements are conducted on a turbulent atmospheric pressure argon plasma jet with a protective gas nozzle, allowing for the creation of a shielding gas curtain around the plasma jets effluent. The results obtained from the hybrid analytical-experimental method are compared to computational fluid dynamics simulations.

  8. Atomic oxygen behavior at downstream of AC excited atmospheric pressure He plasma jet

    Science.gov (United States)

    Takeda, Keigo; Ishikawa, Kenji; Tanaka, Hiromasa; Sekine, Makoto; Hori, Masaru

    2016-09-01

    Applications of atmospheric pressure plasma jets (APPJ) have been investigated in the plasma medical fields such as cancer therapy, blood coagulation, etc. Reactive species generated by the plasma jet interacts with the biological surface. Therefore, the issue attracts much attentions to investigate the plasma effects on targets. In our group, a spot-size AC excited He APPJ have been used for the plasma medicine. From diagnostics of the APPJ using optical emission spectroscopy, the gas temperature and the electron density was estimated to be 299 K and 3.4 ×1015 cm-3. The AC excited He APPJ which affords high density plasma at room temperature is considered to be a powerful tool for the medical applications. In this study, by using vacuum ultraviolet absorption spectroscopy, the density of atomic oxygen on a floating copper as a target irradiated by the He APPJ was measured as a function of the distance between the plasma source and the copper wire. The measured density became a maximum value around 8 ×1013 cm-3 at 12 mm distance, and then decreased over the distance. It is considered that the behavior was due to the changes in the plasma density on the copper wire and influence of ambient air.

  9. DNA damage in oral cancer cells induced by nitrogen atmospheric pressure plasma jets

    Science.gov (United States)

    Han, Xu; Klas, Matej; Liu, Yueying; Stack, M. Sharon; Ptasinska, Sylwia

    2013-09-01

    The nitrogen atmospheric pressure plasma jet (APPJ) has been shown to effectively induce DNA double strand breaks in SCC-25 oral cancer cells. The APPJ source constructed in our laboratory consists of two external electrodes wrapping around a quartz tube and nitrogen as a feed gas and operates based on dielectric barrier gas discharge. Generally, it is more challenging to ignite plasma in N2 atmosphere than in noble gases. However, this design provides additional advantages such as lower costs compared to the noble gases for future clinical operation. Different parameters of the APPJ configuration were tested in order to determine radiation dosage. To explore the effects of delayed damage and cell self-repairing, various incubation times of cells after plasma treatment were also performed. Reactive species generated in plasma jet and in liquid environment are essential to be identified and quantified, with the aim of unfolding the mystery of detailed mechanisms for plasma-induced cell apoptosis. Moreover, from the comparison of plasma treatment effect on normal oral cells OKF6T, an insight to the selectivity for cancer treatment by APPJ can be explored. All of these studies are critical to better understand the damage responses of normal and abnormal cellular systems to plasma radiation, which are useful for the development of advanced plasma therapy for cancer treatment at a later stage.

  10. Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

    Energy Technology Data Exchange (ETDEWEB)

    Kan, C.W., E-mail: tccwk@polyu.edu.hk [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Kwong, C.H. [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Ng, S.P. [Hong Kong Community College, The Hong Kong Polytechnic University (Hong Kong)

    2015-08-15

    Highlights: • Atmospheric pressure plasma treatment improved surface performance of polyester synthetic leather with tetramethylsilane. • XPS and FTIR confirmed the deposition of organosilanes on the sample's surface. • Contact angle increases to 138° after plasma treatment. - Abstract: Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment.

  11. Synthetic-jet-based dynamic stall control on a scaled finite span wind turbine S817 blade

    Science.gov (United States)

    Rice, Thomas; Taylor, Keith; Amitay, Michael

    2016-11-01

    As wind turbines increase in size, so do many of the adverse effects associated with unsteady flow fields. Yawed flow, unsteady gusts, atmospheric boundary layers, and even free stream turbulence can cause unsteady loading, which are detrimental to the blades' structure. In order to decrease unsteady loading, synthetic jet actuators were installed on a scaled finite span cantilevered wind turbine blade having an S817 airfoil shape. The S817 airfoil shape is of the blade tips on the NREL CART3, which will be used next year on full scale field testing of active flow control. The model has been tested in the wind tunnel with and without active flow control, using load, surface pressure, and PIV measurements to characterize the airfoil's stall behavior during static and dynamic conditions, and the effect of flow control on its aerodynamic performance. Surface-mounted microphones were also used to detect dominant frequencies in the flow field. Dynamic stall was also simulated by pitching the airfoil through stall in a sinusoidal pitching motion. Synthetic jets, placed near the leading edge, were shown to increase lift both in the static and dynamic cases, in addition to attaching the flow and reducing hysteresis during dynamic pitching, showing a decrease in structural loading.

  12. Microbial Inactivation in the Liquid Phase Induced by Multigas Plasma Jet.

    Directory of Open Access Journals (Sweden)

    Toshihiro Takamatsu

    Full Text Available Various gas atmospheric nonthermal plasmas were generated using a multigas plasma jet to treat microbial suspensions. Results indicated that carbon dioxide and nitrogen plasma had high sterilization effects. Carbon dioxide plasma, which generated the greatest amount of singlet oxygen than other gas plasmas, killed general bacteria and some fungi. On the other hand, nitrogen plasma, which generated the largest amount of OH radical, killed ≥ 6 log of 11 species of microorganisms, including general bacteria, fungi, acid-fast bacteria, spores, and viruses in 1-15 min. To identify reactive species responsible for bacterial inactivation, antioxidants were added to bacterial suspensions, which revealed that singlet oxygen and OH radicals had greatest inactivation effects.

  13. Influence of Additive Gas on Electrical and Optical Characteristics of Non-equilibrium Atmospheric Pressure Argon Plasma Jet%Influence of Additive Gas on Electrical and Optical Characteristics of Non-equilibrium Atmospheric Pressure Argon Plasma Jet

    Institute of Scientific and Technical Information of China (English)

    费小猛; Shin-ichi KURODA; Yuki KONDO; Tamio MORI; Katsuhiko HOSOI

    2011-01-01

    Electrical and optical properties of an argon plasma jet were characterized. In particular, effects of an additive gas, namely nitrogen or oxygen, on these properties were studied in detail. The plasma jet was found to be of a glow-like discharge, which scarcely changed upon the injection of an additive gas, either directly or through a glass capillary. Optical emission spectroscopy characterization revealed that excited argon atoms were the predominant active species in this plasma jet. Metastable argon atoms were highly quenched, and N2(C3yIu) became the main energy carrier following nitrogen injection. When oxygen was added to the afterglow zone through a glass capillary, no significant quenching effect was observed and the number of oxygen atoms decreased with the increase in oxygen concentration. Finally, to demonstrate an application of this plasma jet, a high-density polyethylene surface was treated with argon, argon/nitrogen, and argon/oxygen plasmas.

  14. First Production of C60 Nanoparticle Plasma Jet for Study of Disruption Mitigation for ITER

    Science.gov (United States)

    Bogatu, I. N.; Thompson, J. R.; Galkin, S. A.; Kim, J. S.; Brockington, S.; Case, A.; Messer, S. J.; Witherspoon, F. D.

    2012-10-01

    Unique fast response and large mass-velocity delivery of nanoparticle plasma jets (NPPJs) provide a novel application for ITER disruption mitigation, runaway electrons diagnostics and deep fueling. NPPJs carry a much larger mass than usual gases. An electromagnetic plasma gun provides a very high injection velocity (many km/s). NPPJ has much higher ram pressure than any standard gas injection method and penetrates the tokamak confining magnetic field. Assimilation is enhanced due to the NP large surface-to-volume ratio. Radially expanding NPPJs help achieving toroidal uniformity of radiation power. FAR-TECH's NPPJ system was successfully tested: a coaxial plasma gun prototype (˜35 cm length, 96 kJ energy) using a solid state TiH2/C60 pulsed power cartridge injector produced a hyper-velocity (>4 km/s), high-density (>10^23 m-3), C60 plasma jet in ˜0.5 ms, with ˜1-2 ms overall response-delivery time. We present the TiH2/C60 cartridge injector output characterization (˜180 mg of sublimated C60 gas) and first production results of a high momentum C60 plasma jet (˜0.6 g.km/s).

  15. Experimental demonstration of Martian soil simulant removal from a surface using a pulsed plasma jet.

    Science.gov (United States)

    Ticoş, C M; Scurtu, A; Toader, D; Banu, N

    2015-03-01

    A plasma jet produced in a small coaxial plasma gun operated at voltages up to 2 kV and working in pure carbon dioxide (CO2) at a few Torr is used to remove Martian soil simulant from a surface. A capacitor with 0.5 mF is charged up from a high voltage source and supplies the power to the coaxial electrodes. The muzzle of the coaxial plasma gun is placed at a few millimeters near the dusty surface and the jet is fired parallel with the surface. Removal of dust is imaged in real time with a high speed camera. Mars regolith simulant JSC-Mars-1A with particle sizes up to 5 mm is used on different types of surfaces made of aluminium, cotton fabric, polyethylene, cardboard, and phenolic.

  16. Atmospheric-pressure plasma jet characterization and applications on melanoma cancer treatment (B/16-F10)

    Energy Technology Data Exchange (ETDEWEB)

    Mashayekh, Shahriar [Physics Department, Shahid Beheshti University, G.C., Evin, 19839-63113 Tehran, Islamic Republic of Iran (Iran, Islamic Republic of); Rajaee, Hajar; Hassan, Zuhir M. [Imonology Department, Faculty of Medical Science, Tarbiat Modarres University, Tehran (Iran, Islamic Republic of); Akhlaghi, Morteza [Laser-Plasma Research Institute, Shahid Beheshti University, G.C., Evin, 19839-63113 Tehran, Islamic Republic of Iran (Iran, Islamic Republic of); Shokri, Babak [Physics Department and Laser-Plasma Research Institute, Shahid Beheshti University, G.C., Evin, 19839-63113 Tehran, Islamic Republic of Iran (Iran, Islamic Republic of)

    2015-09-15

    A new approach in medicine is the use of cold plasma for various applications such as sterilization blood coagulation and cancer cell treatment. In this paper, a pin-to-hole plasma jet for biological applications has been designed and manufactured and characterized. The characterization includes power consumption via Lissajous method, thermal behavior of atmospheric-pressure plasma jet by using Infra-red camera as a novel method and using Speicair software to determine vibrational and transitional temperatures, and optical emission spectroscopy to determine the generated species. Treatment of Melanoma cancer cells (B16/F10) was also implemented, and tetrazolium salt dye (MTT assay) and flow cytometry were used to evaluate viability. Effect of ultraviolet photons on cancerous cells was also observed using an MgF{sub 2} crystal with MTT assay. Finally, in-vivo studies on C57 type mice were also done in order to have a better understanding of the effects in real conditions.

  17. Atmospheric-pressure plasma jet characterization and applications on melanoma cancer treatment (B/16-F10)

    Science.gov (United States)

    Mashayekh, Shahriar; Rajaee, Hajar; Akhlaghi, Morteza; Shokri, Babak; Hassan, Zuhir M.

    2015-09-01

    A new approach in medicine is the use of cold plasma for various applications such as sterilization blood coagulation and cancer cell treatment. In this paper, a pin-to-hole plasma jet for biological applications has been designed and manufactured and characterized. The characterization includes power consumption via Lissajous method, thermal behavior of atmospheric-pressure plasma jet by using Infra-red camera as a novel method and using Speicair software to determine vibrational and transitional temperatures, and optical emission spectroscopy to determine the generated species. Treatment of Melanoma cancer cells (B16/F10) was also implemented, and tetrazolium salt dye (MTT assay) and flow cytometry were used to evaluate viability. Effect of ultraviolet photons on cancerous cells was also observed using an MgF2 crystal with MTT assay. Finally, in-vivo studies on C57 type mice were also done in order to have a better understanding of the effects in real conditions.

  18. Experimental demonstration of Martian soil simulant removal from a surface using a pulsed plasma jet

    Science.gov (United States)

    Ticoş, C. M.; Scurtu, A.; Toader, D.; Banu, N.

    2015-03-01

    A plasma jet produced in a small coaxial plasma gun operated at voltages up to 2 kV and working in pure carbon dioxide (CO2) at a few Torr is used to remove Martian soil simulant from a surface. A capacitor with 0.5 mF is charged up from a high voltage source and supplies the power to the coaxial electrodes. The muzzle of the coaxial plasma gun is placed at a few millimeters near the dusty surface and the jet is fired parallel with the surface. Removal of dust is imaged in real time with a high speed camera. Mars regolith simulant JSC-Mars-1A with particle sizes up to 5 mm is used on different types of surfaces made of aluminium, cotton fabric, polyethylene, cardboard, and phenolic.

  19. Electrical and optical properties of Ar/NH3 atmospheric pressure plasma jet

    Science.gov (United States)

    Chang, Zheng-Shi; Yao, Cong-Wei; Chen, Si-Le; Zhang, Guan-Jun

    2016-09-01

    Inspired by the Penning effect, we obtain a glow-like plasma jet by mixing ammonia (NH3) into argon (Ar) gas under atmospheric pressure. The basic electrical and optical properties of an atmospheric pressure plasma jet (APPJ) are investigated. It can be seen that the discharge mode transforms from filamentary to glow-like when a little ammonia is added into the pure argon. The electrical and optical analyses contribute to the explanation of this phenomenon. The discharge mode, power, and current density are analyzed to understand the electrical behavior of the APPJ. Meanwhile, the discharge images, APPJ's length, and the components of plasma are also obtained to express its optical characteristics. Finally, we diagnose several parameters, such as gas temperature, electron temperature, and density, as well as the density number of metastable argon atoms of Ar/NH3 APPJ to help judge the usability in its applications.

  20. Demonstration of resonant backward Raman amplification in high-density gas-jet plasma

    Science.gov (United States)

    Wu, Z. H.; Zhou, K. N.; Zheng, X. M.; Wei, X. F.; Zhu, Q. H.; Su, J. Q.; Xie, N.; Jiao, Z. H.; Peng, H.; Wang, X. D.; Sun, L.; Li, Q.; Huang, Z.; Zuo, Y. L.

    2016-10-01

    Backward Raman amplification was observed in a 0.7 mm-long high-density gas jet plasma. The 800 nm 30 fs seed pulse was amplified by a factor  ∼28, with an output energy of 2.8 mJ. The output spectra showed that the waveband around 800 nm was significantly amplified. The experimental result demonstrated that the resonant Raman amplification can be realized in high-density plasma against strong plasma instability.

  1. On the design and characterization of a new cold atmospheric pressure plasma jet and its applications on cancer cells treatment.

    Science.gov (United States)

    Akhlaghi, Morteza; Rajayi, Hajar; Mashayekh, Amir Shahriar; Khani, Mohammadreza; Hassan, Zuhair Mohammad; Shokri, Babak

    2015-06-23

    In this paper, a new configuration of a cold atmospheric pressure plasma jet has been designed and constructed. Poly-methyl-methacrylate was used as a new dielectric in this configuration which in comparison to other dielectrics is inexpensive, more resistant against break, and also more shapeable. Then, the plasma jet parameters such as plume temperature, rotational and vibrational temperatures, power, electrical behavior (voltage and current profile), electron density, and the produced reactive species were characterized. In order to determine the jet temperature and the amount of reactive species, effects of applied voltage, gas flow rate, and distance from the nozzle were studied. The power of the jet was specified using Lissajous curve approach. The plume temperature of the plasma jet was about the room temperature. Optical emission spectroscopy determined the type of reactive species, and also electron density and its corresponding plasma frequency (~6.4 × 10(13) cm(-3) and 4.52 × 10(11) Hz). Because of producing different reactive species, the device can be used in different applications, especially in plasma medicine. Thus, 4T1 cancer cells were treated using this plasma jet. The results showed that this plasma jet has a great potential to kill one of the most aggressive and resistant cancerous cell lines.

  2. Application of nonlinear dynamic techniques to high pressure plasma jets

    Science.gov (United States)

    Ghorui, S.; Das, A. K.

    2010-02-01

    Arcs and arc plasmas have been known and used for welding, cutting, chemical synthesis and multitude of other industrial applications for more than hundred years. Though a copious source of heat, light and active species, plasma arc is inherently unstable, turbulent and difficult to control. During recent years, primarily driven by the need of new and energy efficient materials processing, various research groups around the world have been studying new and innovative ways of looking at the issues related to arc dynamics, arc stabilization, species non equilibrium, flow and heat transfer in a stabilized arc plasma device. In this context, experimental determination of nature of arc instabilities using tools of non-linear dynamics, theoretical model formulation, prediction of instability behavior under given operating conditions and possible control methods for the observed instabilities in arcs are reviewed. Space selective probing of the zones inside arc plasma devices without disturbing the system is probably the best way to identify the originating zone of instabilities inside such devices. Existence of extremely high temperature and inaccessibility to direct experimentations due to mechanical obstructions make this task extremely difficult. Probing instabilities in otherwise inaccessible inner regions of the torches, using binary gas mixture as plasma gas is a novel technique that primarily rests on a process known as demixing in arcs. Once a binary gas mixture enters the constricted plasma column, the demixing process sets in causing spatial variations for each of the constituent gases depending on the diffusion coefficients and the gradient of the existing temperature field. By varying concentrations of the constituent gases in the feeding line, it is possible to obtain spatial variations of the plasma composition in a desired manner, enabling spatial probing of the associated zones. Detailed compositional description of different zones inside the torch may be

  3. Two-fluid electromagnetic simulations of plasma-jet acceleration with detailed equation-of-state

    Energy Technology Data Exchange (ETDEWEB)

    Thoma, C.; Welch, D. R.; Clark, R. E.; Bruner, N. [Voss Scientific, LLC, Albuquerque, New Mexico 87108 (United States); MacFarlane, J. J.; Golovkin, I. E. [Prism Computational Sciences, Inc., Madison, Wisconsin 53711 (United States)

    2011-10-15

    We describe a new particle-based two-fluid fully electromagnetic algorithm suitable for modeling high density (n{sub i} {approx} 10{sup 17} cm{sup -3}) and high Mach number laboratory plasma jets. In this parameter regime, traditional particle-in-cell (PIC) techniques are challenging due to electron timescale and lengthscale constraints. In this new approach, an implicit field solve allows the use of large timesteps while an Eulerian particle remap procedure allows simulations to be run with very few particles per cell. Hall physics and charge separation effects are included self-consistently. A detailed equation of state (EOS) model is used to evolve the ion charge state and introduce non-ideal gas behavior. Electron cooling due to radiation emission is included in the model as well. We demonstrate the use of these new algorithms in 1D and 2D Cartesian simulations of railgun (parallel plate) jet accelerators using He and Ar gases. The inclusion of EOS and radiation physics reduces the electron temperature, resulting in higher calculated jet Mach numbers in the simulations. We also introduce a surface physics model for jet accelerators in which a frictional drag along the walls leads to axial spreading of the emerging jet. The simulations demonstrate that high Mach number jets can be produced by railgun accelerators for a variety of applications, including high energy density physics experiments.

  4. Perturbative and nonperturbative aspects of jet quenching in near-critical quark-gluon plasmas

    Science.gov (United States)

    Xu, Jiechen

    In this thesis, we construct two QCD based energy loss models to perform quantitative analysis of jet quenching observables in ultra-relativistic nucleus-nucleus collisions at RHIC and the LHC. We first build up a perturbative QCD based CUJET2.0 jet flavor tomography model that couples the dynamical running coupling DGLV opacity series to bulk data constrained relativistic viscous hydrodynamic backgrounds. It solves the strong heavy quark energy loss puzzle at RHIC and explains the surprising transparency of the quark-gluon plasma (QGP) at the LHC. The observed azimuthal anisotropy of hard leading hadrons requires a path dependent jet-medium coupling in CUJET2.0 that implies physics of nonperturbative origin. To explore the nonperturbative chromo-electric and chromo-magnetic structure of the strongly-coupled QGP through jet probes, we build up a new CUJET3.0 framework that includes in CUJET2.0 both Polyakov loop suppressed semi-QGP chromo-electric charges and emergent chromo-magnetic monopoles in the critical transition regime. CUJET3.0 quantitatively describes the anisotropic hadron suppression at RHIC and the LHC. More significantly, it provides a robust connection between the long wavelength ``perfect fluidity'' of the QGP and the short distance jet transport in the QGP. This framework paves the way for ``measuring'' both perturbative and nonperturbative properties of the QGP, and more importantly for probing color confinement through jet quenching.

  5. Comparison of platelet rich plasma and synthetic graft material for bone regeneration after third molar extraction

    OpenAIRE

    Nathani, Dipesh B.; Sequeira, Joyce; Rao, B. H. Sripathi

    2015-01-01

    Aims: To compare the efficacy of Platelet rich plasma and synthetic graft material for bone regeneration after bilateral third molar extraction. Material and Methods: This study was conducted in 10 patients visiting the outpatient department of Oral & Maxillofacial Surgery, Yenepoya Dental College & Hospital. Patients requiring extraction of bilateral mandibular third molars were taken for the study. Following extraction, PRP (Platelet Rich Plasma) was placed in one extraction socket and synt...

  6. Density limit of H-mode plasmas on JET-ILW

    Energy Technology Data Exchange (ETDEWEB)

    Huber, A., E-mail: a.huber@fz-juelich.de [Institute of Energy and Climate Research – Plasma Physics, Forschungszentrum Jülich GmbH, Trilateral Euregio Cluster, 52425 Jülich (Germany); Brezinsek, S.; Sergienko, G. [Institute of Energy and Climate Research – Plasma Physics, Forschungszentrum Jülich GmbH, Trilateral Euregio Cluster, 52425 Jülich (Germany); Groth, M. [Aalto University, Otakaari 4, 02015 Espoo (Finland); Vries, P.C. de [ITER Organisation, 13115 St Paul Lez Durance (France); Aho-Mantila, L. [VTT Technical Research Centre of Finland, 02044 VTT (Finland); Arnoux, G. [Culham Centre for Fusion Energy, Abingdon OX14 3DB (United Kingdom); Bernert, M. [Max-Planck-Institut für Plasmaphysik, D-85748 Garching (Germany); Beurskens, M.N.A. [Culham Centre for Fusion Energy, Abingdon OX14 3DB (United Kingdom); Calabro, G. [ENEA, Via Enrico Ferri 46, I-0044 Frascati (Italy); Clever, M.; Esser, H.G. [Institute of Energy and Climate Research – Plasma Physics, Forschungszentrum Jülich GmbH, Trilateral Euregio Cluster, 52425 Jülich (Germany); Guillemaut, C. [CEA, IRFM, 13108 St Paul lez Durance (France); Jachmich, S. [Laboratory for Plasma Physics, ERM/KMS, B-1000 Brussels (Belgium); Järvinen, A. [Aalto University, Otakaari 4, 02015 Espoo (Finland); Linsmeier, Ch. [Institute of Energy and Climate Research – Plasma Physics, Forschungszentrum Jülich GmbH, Trilateral Euregio Cluster, 52425 Jülich (Germany); Matthews, G.F.; Meigs, A.G. [Culham Centre for Fusion Energy, Abingdon OX14 3DB (United Kingdom); and others

    2015-08-15

    High-density discharges on JET with ITER-like Wall (ILW) have been analysed with the aim of establishing a mechanism for the H-mode density limit (DL) and compared with experiments in the JET carbon material configuration. The density limit is up to 20% higher in the JET-ILW than in the JET-C machine. The observed H-mode density limit is found close to the Greenwald limit. It is sensitive to the main plasma shape and is almost independent of the heating power. It has been observed that the transition from H-mode to L-mode is not always an abrupt event but may exhibit a series of H–L–H transitions, the so-called “dithering H-mode”. It was observed that detachment, as well as the X-point MARFE itself, does not trigger the H–L transition and thus does not present a limit on the plasma density and that it is the plasma confinement which is ultimately responsible for the H-mode DL.

  7. Effect of plasma jet diameter on the efficiency of reactive oxygen and nitrogen species generation in water

    Science.gov (United States)

    Oh, Jun-Seok; Kakuta, Maito; Furuta, Hiroshi; Akatsuka, Hiroshi; Hatta, Akimitsu

    2016-06-01

    The plasma jet generation of reactive oxygen and nitrogen species (RONS) in solution is important in biology, medicine, and disinfection. Studies using a wide variety of plasma jet devices have been carried out for this purpose, making it difficult to compare the performance between devices. In this study, we compared the efficiency of RONS generation in deionized (DI) water between 3.7-mm- and 800-µm-sized helium (He) plasma jets (hereafter mm-jet and µm-jet, respectively) at different treatment distances and times. The efficiency of RONS generation was determined by considering the total amount of RONS generated in DI water with respect to the input energy and gas consumption. We found that the mm-jet generated 20% more RONS in the DI water than the µm-jet at the optimized distance. However, when the input power and He gas consumption were taken into account, we discovered that the µm-jet was 5 times more efficient in generating RONS in the DI water. Under the parameters investigated in this study, the concentration of RONS continued to increase as a function of treatment time (up to 30 min). However treatment distance had a marked effect on the efficiency of RONS generation: treatment distances of 25 and 30 mm were optimal for the mm-jet and µm-jet, respectively. Our method of comparing the efficiency of RONS generation in solution between plasma jets could be used as a reference protocol for the development of efficient plasma jet sources for use in medicine, biology, and agriculture.

  8. Heat Transfer from a dc Laminar Plasma-Jet Flow to Different Solid Surfaces

    Institute of Scientific and Technical Information of China (English)

    孟显; 潘文霞; 吴承康

    2003-01-01

    The heat flux distributions were measured by using transient method for an argon dc laminar plasma-jet flow impinging normally on a plate surface embedded with copper probes. Different powders were coated on the probe surfaces and the effect of powder coatings on the heat transfer from jet flow to the probe surface was examined.Experimental results show that the maximum values of the heat flux to the probe increase with the coating of fine metal powders, while for the surfaces coated with fine ceramic powders, the maximum values of heat flux decrease, compared with that to the bare copper probe surface.

  9. Beryllium plasma-facing components for the ITER-like wall project at JET

    Energy Technology Data Exchange (ETDEWEB)

    Rubel, M J; Sundelin, P [Alfven Laboratory, Royal Institute of Technology, Association Euratom-VR (Sweden); Bailescu, V [Nuclear Fuel Plant, Pitesti (Romania); Coad, J P; Matthews, G F; Pedrick, L; Riccardo, V; Villedieu, E [Culham Science Centre, Euratom-UKAEA Fusion Association, Abingdon (United Kingdom); Hirai, T; Linke, J [IEF-2, Forschungszentrum Juelich, Association Euratom-FZJ, Juelich (Germany); Likonen, J [VTT, Association Euratom-Tekes, 02044 VTT (Finland); Lungu, C P [NILPRP, Association Euratom-MEdC, Bucharest (Romania)], E-mail: rubel@kth.se

    2008-03-15

    ITER-Like Wall Project has been launched at the JET tokamak in order to study a tokamak operation with beryllium components on the main chamber wall and tungsten in the divertor. To perform this first comprehensive test of both materials in a thermonuclear fusion environment, a broad program has been undertaken to develop plasma-facing components and assess their performance under high power loads. The paper provides a concise report on scientific and technical issues in the development of a beryllium first wall at JET.

  10. Risk assessment of a cold argon plasma jet in respect to its mutagenicity.

    Science.gov (United States)

    Wende, K; Bekeschus, S; Schmidt, A; Jatsch, L; Hasse, S; Weltmann, K D; Masur, K; von Woedtke, T

    2016-03-01

    Cold atmospheric pressure plasmas represent a favorable option for the treatment of heat sensitive materials and human or animal tissue. Beneficial effects have been documented in a variety of medical conditions, e.g., in the treatment of chronic wounds. It is assumed that the main mechanism of the plasma's efficacy is mediated by a stimulating dissipation of energy via radiation and/or chemical energy. Although no evidence on undesired side effects of a plasma treatment has yet been presented, skepticism toward the safety of the exposure to plasma is present. However, only little data regarding the mutagenic potential of this new treatment option is available. Accordingly, we investigated the mutagenic potential of an argon plasma jet (kinpen) using different testing systems in accordance with ISO norms and multiple cell lines: a HPRT1 mutation assay, a micronucleus formation assay, and a colony formation assay. Moderate plasma treatment up to 180 s did not increase genotoxicity in any assay or cell type investigated. We conclude that treatment with the argon plasma jet kinpen did not display a mutagenic potential under the test conditions applied and may from this perspective be regarded as safe for the use in biomedical applications.

  11. Cold plasma interactions with plants: Morphing and movements of Venus flytrap and Mimosa pudica induced by argon plasma jet.

    Science.gov (United States)

    Volkov, Alexander G; Xu, Kunning G; Kolobov, Vladimir I

    2017-12-01

    Low temperature (cold) plasma finds an increasing number of applications in biology, medicine and agriculture. In this paper, we report a new effect of plasma induced morphing and movements of Venus flytrap and Mimosa pudica. We have experimentally observed plasma activation of sensitive plant movements and morphing structures in these plants similar to stimulation of their mechanosensors in vivo. Application of an atmospheric pressure argon plasma jet to the inside or outside of a lobe, midrib, or cilia in Dionaea muscipula Ellis induces trap closing. Treatment of Mimosa pudica by plasma induces movements of pinnules and petioles similar to the effects of mechanical stimulation. We have conducted control experiments and simulations to illustrate that gas flow and UV radiation associated with plasma are not the primary reasons for the observed effects. Reactive oxygen and nitrogen species (RONS) produced by cold plasma in atmospheric air appear to be the primary reason of plasma-induced activation of phytoactuators in plants. Some of these RONS are known to be signaling molecules, which control plants' developmental processes. Understanding these mechanisms could promote plasma-based technology for plant developmental control and future use for plant protection from pathogens. Our work offers new insight into mechanisms which trigger plant morphing and movement. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Computational study of the interaction of cold atmospheric helium plasma jets with surfaces

    Science.gov (United States)

    Breden, Douglas; Raja, Laxminarayan L.

    2014-12-01

    We describe a computational modeling study of a cold atmospheric pressure plasma jet interacting with a dielectric surface placed normal to the jet axis. The plasma jet is generated by the application of a nanosecond pulse voltage applied to a dielectric tube through which the jet issues into ambient air. A base fluid flow field is pre-computed using a Navier-Stokes model for the helium jet impinging on the dielectric target surface with a two-species description for laminar diffusional mixing of the helium and ambient air streams. A self-consistent, multiple species, two-temperature model is used to describe the non-equilibrium plasma discharge dynamics in the presence of the base jet flow field. A single nanosecond pulse discharge event starting from initial breakdown in the dielectric tube, to propagation into the open gap, and finally the interaction with the dielectric surface is simulated. Initially, the plasma forms within the dielectric tube and propagates along the tube surface as a surface discharge driven by large induced electric fields produced by trapped charge on the dielectric surface. When the discharge reaches the end of the dielectric tube, the discharge transitions to a constricted fast ionization wave that propagates along the helium-air interface. The fast ionization wave eventually reaches the dielectric target surface where charged species are deposited as the discharge propagates parallel to the wall as a surface driven discharge. The surface driven discharge ceases to propagate once the quantity of air to helium is sufficient enough to quench the hot electrons and prevent further ionization. Due to the low speed of the flow discharge and the short life times of the radical species such as O, most of the radical species delivered to the surface are a result of the surface discharge that forms after the plasma bullet impinges against the surface. It is found that factors such as the thickness of the target dielectric and the profile of the

  13. Experimental, Numerical and Analytical Studies of the MHD-driven plasma jet, instabilities and waves

    Science.gov (United States)

    Zhai, Xiang

    This thesis describes a series of experimental, numerical, and analytical studies involving the Caltech magnetohydrodynamically (MHD)-driven plasma jet experiment. The plasma jet is created via a capacitor discharge that powers a magnetized coaxial planar electrodes system. The jet is collimated and accelerated by the MHD forces. We present three-dimensional ideal MHD finite-volume simulations of the plasma jet experiment using an astrophysical magnetic tower as the baseline model. A compact magnetic energy/helicity injection is exploited in the simulation analogous to both the experiment and to astrophysical situations. Detailed analysis provides a comprehensive description of the interplay of magnetic force, pressure, and flow effects. We delineate both the jet structure and the transition process that converts the injected magnetic energy to other forms. When the experimental jet is sufficiently long, it undergoes a global kink instability and then a secondary local Rayleigh-Taylor instability caused by lateral acceleration of the kink instability. We present an MHD theory of the Rayleigh-Taylor instability on the cylindrical surface of a plasma flux rope in the presence of a lateral external gravity. The Rayleigh-Taylor instability is found to couple to the classic current-driven instability, resulting in a new type of hybrid instability. The coupled instability, produced by combination of helical magnetic field, curvature of the cylindrical geometry, and lateral gravity, is fundamentally different from the classic magnetic Rayleigh-Taylor instability occurring at a two-dimensional planar interface. In the experiment, this instability cascade from macro-scale to micro-scale eventually leads to the failure of MHD. When the Rayleigh-Taylor instability becomes nonlinear, it compresses and pinches the plasma jet to a scale smaller than the ion skin depth and triggers a fast magnetic reconnection. We built a specially designed high-speed 3D magnetic probe and

  14. Divertor plasma conditions and neutral dynamics in horizontal and vertical divertor configurations in JET-ILW low confinement mode plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Groth, M., E-mail: mathias.groth@aalto.fi [Aalto University, Association EURATOM-Tekes, Otakaari 4, Espoo (Finland); Brezinsek, S. [Forschungszentrum Jülich, IEK4 – Plasma Physik, Jülich (Germany); Belo, P. [Institute of Plasmas and Nuclear Fusion, Association EURATOM/IST, Lisbon (Portugal); Culham Centre for Fusion Energy, Association EURATOM-CCFE, Abingdon (United Kingdom); Brix, M. [Culham Centre for Fusion Energy, Association EURATOM-CCFE, Abingdon (United Kingdom); Calabro, G. [Association EURATOM-ENEA, Frascati (Italy); Chankin, A. [Max-Planck Institute for Plasma Physics, EURATOM Association, Garching (Germany); Clever, M.; Coenen, J.W. [Forschungszentrum Jülich, IEK4 – Plasma Physik, Jülich (Germany); Corrigan, G. [Culham Centre for Fusion Energy, Association EURATOM-CCFE, Abingdon (United Kingdom); Drewelow, P. [Max-Planck-Institute for Plasma Physics, EURATOM Association, Greifswald (Germany); Guillemaut, C. [Association EURATOM CEA, CEA/DSM/IRFM, Cadarache (France); Harting, D. [Culham Centre for Fusion Energy, Association EURATOM-CCFE, Abingdon (United Kingdom); Huber, A. [Forschungszentrum Jülich, IEK4 – Plasma Physik, Jülich (Germany); Jachmich, S. [Association ‘Euratom-Belgian state’, Ecole Royale Militaire, Brussels (Belgium); Järvinen, A. [Aalto University, Association EURATOM-Tekes, Otakaari 4, Espoo (Finland); Kruezi, U.; Lawson, K.D. [Culham Centre for Fusion Energy, Association EURATOM-CCFE, Abingdon (United Kingdom); Lehnen, M. [Forschungszentrum Jülich, IEK4 – Plasma Physik, Jülich (Germany); ITER Organisation, 13115 Saint-Paul-Lez-Durance (France); and others

    2015-08-15

    Measurements of the plasma conditions at the low field side target plate in JET ITER-like wall ohmic and low confinement mode plasmas show minor differences in divertor plasma configurations with horizontally and vertically inclined targets. Both the reduction of the electron temperature in the vicinity of the strike points and the rollover of the ion current to the plates follow the same functional dependence on the density at the low field side midplane. Configurations with vertically inclined target plates, however, produce twice as high sub-divertor pressures for the same upstream density. Simulations with the EDGE2D-EIRENE code package predict significantly lower plasma temperatures at the low field side target in vertical than in horizontal target configurations. Including cross-field drifts and imposing a pumping by-pass leak at the low-field side plate can still not recover the experimental observations.

  15. Full jet evolution in quark-gluon plasma and nuclear modification of jet production and jet shape in Pb+Pb collisions at 2.76 A TeV at the CERN Large Hadron Collider

    Science.gov (United States)

    Chang, Ning-Bo; Qin, Guang-You

    2016-08-01

    We study the evolution of the full jet shower in quark-gluon plasma by solving a set of coupled differential transport equations for the three-dimensional momentum distributions of quarks and gluons contained in full jets. In our jet evolution equations, we include all partonic splitting processes as well as the collisional energy loss and transverse momentum broadening for both the leading and radiated partons of the full jets. Combining with a realistic (2 +1 )-dimensional viscous hydrodynamic simulation for the spacetime profiles of the hot and dense nuclear medium produced in heavy-ion collisions, we apply our formalism to calculate the nuclear modification of single inclusive full jet spectra, the momentum imbalance of photon-jet and dijet pairs, and the jet shape function (at partonic level) in Pb+Pb collisions at 2.76 A TeV. The roles of various jet-medium interaction mechanisms on the full jet modification are studied. We find that the nuclear modification of jet shape is sensitive to the interplay of different interaction mechanisms as well as the energies of the full jets.

  16. Compatibility of Fuels and Radicals Found in Plasma Jets for Improved Premixed Combustion

    Science.gov (United States)

    Yamamoto, Yohji; Shimotani, Kouhei; Shuzenji, Kiyotaka; Kakami, Akira; Tachibana, Takeshi

    We examined the compatibility of radicals contained in plasma jets to fuels through ignition and combustion tests for dimethyl ether (DME)/air and methane (CH4)/air mixtures with oxygen (O2) and nitrogen (N2) as the plasma torch feedstocks. The experiment showed that the DME/air mixture was ignited/combusted with less plasma jet (P.J.) power than the CH4/air mixture and that the O2 P.J. is more effective than the N2 P.J., with a more distinct difference in effectiveness for the CH4/air mixture in contrast to the DME/air mixture. Plasma jets with fewer feedstock flow rates were more effective, presumably due to the greater amount of radical production under the conditions tested. Numerical estimation on the amount of radicals and ignition delay time demonstrates that the superiority of the O2 P.J. is not necessarily only due to the effectiveness of the O radicals, but also due to the fact they were produced easier and with less power, and that the effect and behavior according to amount is different for fuels. This is most likely because they depend on the reaction mechanism of each mixture, all of which match well with the experimental results.

  17. Controlling the nitric and nitrous oxide production of an atmospheric pressure plasma jet

    Science.gov (United States)

    Douat, Claire; Hubner, Simon; Engeln, Richard; Benedikt, Jan

    2016-09-01

    Atmospheric pressure plasma jets are non-thermal plasmas and have the ability to create reactive species. These features make it a very attractive tool for biomedical applications. In this work, we studied NO and N2O production, which are two species having biomedical properties. NO plays a role in the vascularization and in ulcer treatment, while N2O is used as anesthetic and analgesic gas. In this study, the plasma source is similar to the COST Reference Microplasma Jet (µ-APPJ). Helium is used as feed gas with small admixtures of molecular nitrogen and oxygen of below 1%. The absolute densities of NO and N2O were measured in the effluent of an atmospheric pressure RF plasma jet by means of ex-situ quantum-cascade laser absorption spectroscopy via a multi-pass cell in Herriot configuration. We will show that the species' production is dependent on several parameters such as power, flow and oxygen and nitrogen admixture. The NO and N2O densities are strongly dependent on the N2-O2 ratio. Changing this ratio allows for choosing between a NO-rich or a N2O-rich regime.

  18. Inactivation of Gram-positive biofilms by low-temperature plasma jet at atmospheric pressure

    Science.gov (United States)

    Marchal, F.; Robert, H.; Merbahi, N.; Fontagné-Faucher, C.; Yousfi, M.; Romain, C. E.; Eichwald, O.; Rondel, C.; Gabriel, B.

    2012-08-01

    This work is devoted to the evaluation of the efficiency of a new low-temperature plasma jet driven in ambient air by a dc-corona discharge to inactivate adherent cells and biofilms of Gram-positive bacteria. The selected microorganisms were lactic acid bacteria, a Weissella confusa strain which has the particularity to excrete a polysaccharide polymer (dextran) when sucrose is present. Both adherent cells and biofilms were treated with the low-temperature plasma jet for different exposure times. The antimicrobial efficiency of the plasma was tested against adherent cells and 48 h-old biofilms grown with or without sucrose. Bacterial survival was estimated using both colony-forming unit counts and fluorescence-based assays for bacterial cell viability. The experiments show the ability of the low-temperature plasma jet at atmospheric pressure to inactivate the bacteria. An increased resistance of bacteria embedded within biofilms is clearly observed. The resistance is also significantly higher with biofilm in the presence of sucrose, which indicates that dextran could play a protective role.

  19. Radiation from high-intensity ultrashort-laser-pulse and gas-jet magnetized plasma interaction.

    Science.gov (United States)

    Dorranian, Davoud; Starodubtsev, Mikhail; Kawakami, Hiromichi; Ito, Hiroaki; Yugami, Noboru; Nishida, Yasushi

    2003-08-01

    Using a gas-jet flow, via the interaction between an ultrashort high-intensity laser pulse and plasma in the presence of a perpendicular external dc magnetic field, the short pulse radiation from a magnetized plasma wakefield has been observed. Different nozzles are used in order to generate different densities and gas profiles. The neutral density of the gas-jet flow measured with a Mach-Zehnder interferometer is found to be proportional to back pressure of the gas jet in the range of 1 to 8 atm. Strength of the applied dc magnetic field varies from 0 to 8 kG at the interaction region. The frequency of the emitted radiation with the pulse width of 200 ps (detection limit) is in the millimeter wave range. Polarization and spatial distributions of the experimental data are measured to be in good agreement with the theory based on the V(p)xB radiation scheme, where V(p) is the phase velocity of the electron plasma wave and B is the steady magnetic field intensity. Characteristics of the radiation are extensively studied as a function of plasma density and magnetic field strength. These experiments should contribute to the development of a new kind of millimeter wavelength radiation source that is tunable in frequency, pulse duration, and intensity.

  20. Simulation of Plasma Jet Merger and Liner Formation within the PLX- α Project

    Science.gov (United States)

    Samulyak, Roman; Chen, Hsin-Chiang; Shih, Wen; Hsu, Scott

    2015-11-01

    Detailed numerical studies of the propagation and merger of high Mach number argon plasma jets and the formation of plasma liners have been performed using the newly developed method of Lagrangian particles (LP). The LP method significantly improves accuracy and mathematical rigor of common particle-based numerical methods such as smooth particle hydrodynamics while preserving their main advantages compared to grid-based methods. A brief overview of the LP method will be presented. The Lagrangian particle code implements main relevant physics models such as an equation of state for argon undergoing atomic physics transformation, radiation losses in thin optical limit, and heat conduction. Simulations of the merger of two plasma jets are compared with experimental data from past PLX experiments. Simulations quantify the effect of oblique shock waves, ionization, and radiation processes on the jet merger process. Results of preliminary simulations of future PLX- alpha experiments involving the ~ π / 2 -solid-angle plasma-liner configuration with 9 guns will also be presented. Partially supported by ARPA-E's ALPHA program.

  1. Observations of rotation in JET plasmas with electron heating by ion cyclotron resonance heating

    DEFF Research Database (Denmark)

    Hellsten, T.; Johnson, T. J.; Van Eester, D.

    2012-01-01

    The rotation of L-mode plasmas in the JET tokamak heated by waves in the ion cyclotron range of frequencies (ICRF) damped on electrons, is reported. The plasma in the core is found to rotate in the counter-current direction with a high shear and in the outer part of the plasma with an almost...... constant angular rotation. The core rotation is stronger in magnitude than observed for scenarios with dominating ion cyclotron absorption. Two scenarios are considered: the inverted mode conversion scenarios and heating at the second harmonic He-3 cyclotron resonance in H plasmas. In the latter case......, electron absorption of the fast magnetosonic wave by transit time magnetic pumping and electron Landau damping (TTMP/ELD) is the dominating absorption mechanism. Inverted mode conversion is done in (He-3)-H plasmas where the mode converted waves are essentially absorbed by electron Landau damping. Similar...

  2. Dynamic Properties of Helium Atmospheric Dielectric-Barrier-Discharge Plasma Jet.

    Science.gov (United States)

    Uchida, Giichiro; Takenaka, Kosuke; Miyazaki, Atsushi; Kawabata, Kazufumi; Setsuhara, Yuichi

    2015-03-01

    We present here experiments on helium atmospheric dielectric-barrier discharge jet in open air. A long stable plasma plume is realized at high applied voltage and high gas flow rate. Optical emission measurements show that the plasma plume consists of two part: a plume head with high energy electrons and a tail part with low energy electrons. The plasma plume propagates away from the quartz-tube outlet with about 30-80 km/sec along the helium gas flow channel. The propagation velocity of plasma plume is in the time scale of electron drift velocity, and the electric field plays an important role as a driving force of the plasma plume propagation.

  3. Observation of the Emission Spectra of an Atmospheric Pressure Radio-frequency Plasma Jet

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    An atmospheric pressure plasma jet (APPJ) using radio-frequency (13.56 MHz)power has been developed to produce homogeneous glow discharge at low temperature. With optical emission spectroscopy, we observed the excited species (atomic helium, atomic oxygen and metastable oxygen) generated in this APPJ and their dependence on gas composition ratio and RF power. O and O2(b1∑g+) are found in the effluent outside the jet by measuring the emission spectra of effluent perpendicular to the jet. An interesting phenomenon is found that there is an abnormal increase of O emission intensity (777.4 nm) between 10 mm and 40 mm away from the nozzle. This observation result is very helpful in practical operation.

  4. Experimental evidence for collisional shock formation via two obliquely merging supersonic plasma jets

    CERN Document Server

    Merritt, Elizabeth C; Hsu, Scott C; Adams, Colin S; Gilmore, Mark A

    2013-01-01

    We report spatially resolved experimental measurements of the oblique merging of two supersonic laboratory plasma jets. The jets are formed and launched by pulsed-power-driven railguns using injected argon, and have electron density $\\sim 10^{14}$ cm$^{-3}$, electron temperature $\\approx 1.4$ eV, ionization fraction near unity, and velocity $\\approx 40$ km/s just prior to merging. The jet merging produces a few-cm-thick stagnation layer, as observed in both fast-framing camera images and multi-chord interferometer data, consistent with collisional shock formation [E. C. Merritt et al., Phys. Rev. Lett. 111, 085003 (2013)]. The observed stagnation layer emission morphology is consistent with hydrodynamic oblique shock theory at early times, and then undergoes an evolution at later times that is coincident with the theoretically predicted transition to detached shock formation.

  5. Influence of voltage magnitude on the dynamic behavior of a stable helium atmospheric pressure plasma jet

    Science.gov (United States)

    Ning, Wenjun; Wang, Lijun; Wu, Chen; Jia, Shenli

    2014-08-01

    Effects of voltage magnitude on the development of a stable helium atmospheric pressure plasma jet are investigated by current measurements and high temporal-resolution streak images. Generated by a coaxial dielectric barrier discharge structure, the entire discharge can be classified into three regions: discharges in the tube gap, downstream jet, and up-streamer. The discharge morphologies of each region are analyzed. In the positive discharge phase, there are two discharges in the tube gap between the electrodes; the first one is ignited as corona and then developed into streamer corona, and the second one is similar with positive glow. The downstream jet is ignited independently from the discharge in the tube gap. Referred as "plasma bullet," the dynamic behavior of the jet can be well described as a positive streamer. Under specific applied voltage, the jet is found to be composed by double bullets in which case the jet length decreases since that less charge is carried by the first bullet. The up-streamer can be captured as long as the discharge in the tube gap is activated. Propagating with velocity of ˜4 km/s, the up-streamer can be regarded as the extension of the first discharge in the tube gap. In the negative discharge phase, the discharge is confined in the tube gap with nearly symmetrical morphology with the positive one. Besides, with the rising of voltage, the negative discharge is initially intensified and then turns weaker after surpassing certain voltage, which may provide suitable condition for the occurrence of double-bullet phenomenon.

  6. Propagation mechanisms of guided streamers in plasma jets: the influence of electronegativity of the surrounding gas

    Science.gov (United States)

    Schmidt-Bleker, Ansgar; Norberg, Seth A.; Winter, Jörn; Johnsen, Eric; Reuter, S.; Weltmann, K. D.; Kushner, Mark J.

    2015-06-01

    Atmospheric pressure plasma jets for biomedical applications are often sustained in He with small amounts of, for example, O2 impurities and typically propagate into ambient air. The resulting poorly controlled generation of reactive species has motivated the use of gas shields to control the interaction of the plasma plume with the ambient gas. The use of different gases in the shield yields different behavior in the plasma plume. In this paper, we discuss results from experimental and computational investigations of He plasma jets having attaching and non-attaching gas shields. We found that negative ion formation in the He-air mixing region significantly affects the ionization wave dynamics and promotes the propagation of negative guided streamers through an electrostatic focusing mechanism. Results from standard and phase resolved optical emission spectroscopy ratios of emission from states of N2 and He imply different electric fields in the plasma plume depending on the composition of the shielding gas. These effects are attributed to the conductivity in the transition region between the plasma plume and the shield gas, and the immobile charge represented by negative ions. The lower conductivity in the attaching mixtures enables more extended penetration of the electric field whereas the negative ions aid in focusing the electrons towards the axis.

  7. A donut-shape distribution of OH radicals in atmospheric pressure plasma jets

    Science.gov (United States)

    Yue, Yuanfu; Wu, Fan; Cheng, He; Xian, Yubin; Liu, Dawei; Lu, Xinpei; Pei, Xuekai

    2017-01-01

    In this work, OH radicals that have a donut-shape distribution in the room-temperature atmospheric-pressure plasma jet are investigated using the laser-induced fluorescence method. The plasma jet driven by a pulse power supply is operated under two conditions: without the ground electrode and with the ground electrode. It is found that the OH radicals distribute as a donut-shape for the first several pulses under both two conditions. With more pulses applied, the donut-shape disappears and OH radicals distribute as a solid disk. Detailed investigations show that the total OH radicals in the plasma plume are formed from two parts. One part is generated by the plasma plume outside the tube with a structure of a donut-shape. The other part is generated by the plasma inside the tube with a structure of a solid disk, which can be transported to the downstream with gas stream and leads to the disappearance of the donut-shape in the plasma plum. Moreover, when the ground electrode is applied, higher intensity of OH is obtained as well as OH donut-shape distribution is observed with dehumidified working gas. It may be due to the higher electron density and its donut-shape distribution in the effluent according to the simulations and experimental results.

  8. Faraday Conversion in Turbulent Blazar Jets

    CERN Document Server

    MacDonald, Nicholas R

    2016-01-01

    Low ($\\lesssim 3\\%$) levels of circular polarization (CP) detected at radio frequencies in the relativistic jets of some blazars can provide insight into the underlying nature of the jet plasma. CP can be produced through linear birefringence, in which initially linearly polarized emission produced in one region of the jet is altered by Faraday rotation as it propagates through other regions of the jet with various magnetic field orientations. Marscher has recently begun a study of jets with such magnetic geometries with the Turbulent Extreme Multi-Zone (TEMZ) model, in which turbulent plasma crossing a standing shock in the jet is represented by a collection of thousands of individual plasma cells, each with distinct magnetic field orientation. Here we develop a radiative transfer scheme that allows the numerical TEMZ code to produce simulated images of the time-dependent linearly and circularly polarized intensity at different radio frequencies. In this initial study, we produce synthetic polarized emission...

  9. Design and Experimental Research on Piezoelectric Synthetic Jet Actuator%压电式合成射流致动器的设计与实验研究

    Institute of Scientific and Technical Information of China (English)

    郝礼书; 乔志德

    2009-01-01

    Synthetic jet actuator was designed by different form of the vents and layout of the piezoelectric vibrators,which was designed by two different piezoelectric ceramics.The hot wire anemometry was used to measure the velocity in the vent center flow from the actuator.Results showed that the peak-value velocity of designed synthetic jet actuator was 22.55 m/s.The jet angle of inclination was an important factor to the peak-value velocity of synthetic jet actuator designed by the piezoelectric vibrators typical layout.More kinetic energy was acquired at 900 jet angle than 450 jet angle.The layout form of the piezoelectric vibrators was another important factor of the peak-value velocity of synthetic jet actuator; more kinetic energy was acquired by typical layout than side layout.%采用两种不同的压电陶瓷片制作了压电振子,基于压电振子设计了不同喷口形式和压电振子布局形式的合成射流致动器.实验中利用热线风速仪对致动器喷口中心的速度进行了测量.结果表明,所设计的合成射流致动器喷口峰值速度达22.55 m/s,致动器典型布局时方形缝倾斜角对喷口峰值速度影响较大,90°法向射流比45°倾斜射流能获得更大的喷口动能,射流法向喷出时致动器典型布局比侧面布局能获得更多的喷口动能.

  10. MHD marking using the MSE polarimeter optics in ILW JET plasmas

    Science.gov (United States)

    Reyes Cortes, S.; Alper, B.; Alves, D.; Baruzzo, M.; Bernardo, J.; Buratti, P.; Coelho, R.; Challis, C.; Chapman, I.; Hawkes, N.; Hender, T. C.; Hobirk, J.; Joffrin, E.

    2016-11-01

    In this communication we propose a novel diagnostic technique, which uses the collection optics of the JET Motional Stark Effect (MSE) diagnostic, to perform polarimetry marking of observed MHD in high temperature plasma regimes. To introduce the technique, first we will present measurements of the coherence between MSE polarimeter, electron cyclotron emission, and Mirnov coil signals aiming to show the feasibility of the method. The next step consists of measuring the amplitude fluctuation of the raw MSE polarimeter signals, for each MSE channel, following carefully the MHD frequency on Mirnov coil data spectrograms. A variety of experimental examples in JET ITER-Like Wall (ILW) plasmas are presented, providing an adequate picture and interpretation for the MSE optics polarimeter technique.

  11. Evaluation of plasma jet ignition for improved performance of alternate fuels

    Science.gov (United States)

    Grant, J. F.; Golenko, Z.; McIlwain, M. E.

    1982-08-01

    Alcohols, such as ethanol and methanol, are potential substitutes for gasolines during periods of fuel shortages. The pure alcohols have been reported to cause performance and starting problems when used to fuel internal combustion engines. This study characterized how three modes of ignition, OEM magneto, high energy conventional spark (CI) and plasma jet ignition (PJI) influenced the engine combustion properties of ethanol, methanol and gasoline alcohol blends. Specific combustion properties examined in these measurement were burning velocity and lean limit. In addition, the engine performance was determined for 30% alcohol gasoline containing blends. These engine performance measurements determined brake power, brake specific fuel consumption and brake emissions of carbon monoxide and hydrocarbons. The findings of this study suggest that high energy ignition systems, such as plasma jet ignition, will improve both fuel combustion properties and engine performance.

  12. DC high voltage to drive helium plasma jet comprised of repetitive streamer breakdowns

    CERN Document Server

    Wang, Xingxing

    2016-01-01

    This paper demonstrates and studies helium atmospheric pressure plasma jet comprised of series of repetitive streamer breakdowns, which is driven by a pure DC high voltage (auto-oscillations). Repetition frequency of the breakdowns is governed by the geometry of discharge electrodes/surroundings and gas flow rate. Each next streamer is initiated when the electric field on the anode tip recovers after the previous breakdown and reaches the breakdown threshold value of about 2.5 kV/cm. Repetition frequency of the streamer breakdowns excited using this principle can be simply tuned by reconfiguring the discharge electrode geometry. This custom-designed type of the helium plasma jet, which operates on the DC high voltage and is comprised of the series of the repetitive streamer breakdowns at frequency about 13 kHz, is demonstrated.

  13. MHD marking using the MSE polarimeter optics in ILW JET plasmas

    CERN Document Server

    Reyes Cortes, S.; Alves, D.; Baruzzo, M.; Bernardo, J.; Buratti, P.; Coelho, R.; Challis, C.; Chapman, I.; Hawkes, N.; Hender, T.C.; Hobirk, J.; Joffrin, E.

    2016-01-01

    In this communication we propose a novel diagnostic technique, which uses the collection optics of the JET Motional Stark Effect (MSE) diagnostic, to perform polarimetry marking of observed MHD in high temperature plasma regimes. To introduce the technique, first we will present measurements of the coherence between MSE polarimeter, electron cyclotron emission, and Mirnov coil signals aiming to show the feasibility of the method. The next step consists of measuring the amplitude fluctuation of the raw MSE polarimeter signals, for each MSE channel, following carefully the MHD frequency on Mirnov coil data spectrograms. A variety of experimental examples in JET ITER-Like Wall (ILW) plasmas are presented, providing an adequate picture and interpretation for the MSE optics polarimeter technique.

  14. Operational experience with a variety of plasma facing tile assemblies at JET

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, P. E-mail: paul.edwards@jet.uk; Altmann, H.; Loving, A.; Pedrick, L.; Tait, J.; Way, M

    2001-10-01

    During the June 1999 JET shutdown, 3000 plasma facing Tile Assemblies were found to be loose and had to be re-torqued remotely using the Mascot force reflecting manipulator. Whilst the integrity of these Tile Assemblies has been monitored during previous man access shutdowns, with the introduction of tritium to the machine in May 1996, the majority had not been checked since March 1996. This paper reviews typical plasma facing Tile Assembly designs within the JET torus and summarises the experience gained for use in future machine applications. This includes loosening processes/mechanisms and their prevention, applications of surface coatings to avoid seizing of un-lubricated assemblies, and the use of vibration resistant thread profiles. The design of attachments to minimise combined mechanical and thermal stresses in the tiles, material selection and other engineering aspects are also discussed.

  15. Comparison of Sterilizing Effect of Nonequilibrium Atmospheric-Pressure He/O2 and Ar/O2 Plasma Jets

    Science.gov (United States)

    Li, Shouzhe; Lim, Jinpyo

    2008-02-01

    The sterilizing effect of the non-equilibrium atmospheric pressure plasma jet by applying it to the Bacillus subtilis spores is invesigated. A stable glow discharge in argon or helium gas fed with active gas (oxygen), was generated in the coaxial cylindrical reactor powered by the radio-frequency power supply at atmospheric pressure. The experimental results indicated that the efficiency of killing spores by making use of an Ar/O2 plasma jet was much better than with a He/O2 plasma jet. The decimal reduction value of Ar/O2 and He/O2 plasma jets under the same experimental conditions was 4.5 seconds and 125 seconds, respectively. It was found that there exists an optimum oxygen concentration for a certain input power, at which the sterilization efficiency reaches a maximum value. It is believed that the oxygen radicals are generated most efficiently under this optimum condition.

  16. Comparison of Sterilizing Effect of Nonequilibrium Atmospheric-Pressure He/O2 and Ar/O2 Plasma Jets

    Institute of Scientific and Technical Information of China (English)

    LI Shouzhe; LIM Jinpyo

    2008-01-01

    The sterilizing effect of the non-equilibrium atmospheric pressure plasma jet by applying it to the Bacillus subtilis spores is invesigated. A stable glow discharge in argon or helium gas fed with active gas (oxygen), was generated in the coaxial cylindrical reactor powered by the radio-frequency power supply at atmospheric pressure. The experimental results indicated that the efficiency of killingspores by making use of an Ar/O2 plasma jet was much better than with a He/O2 plasma jet. The decimal reduction value of Ar/O2 and He/O2 plasma jets under the same experimental conditions was 4.5 seconds and 125 seconds, respectively. It was found that there exists an optimum oxygen concentration for a certain input power, at which the sterilization efficiency reaches a maximum value. It is believed that the oxygen radicals are generated most efficiently under this optimum condition.

  17. Rayleigh-Taylor-Instability Evolution in Colliding-Plasma-Jet Experiments with Magnetic and Viscous Stabilization

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Colin Stuart [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Univ. of New Mexico, Albuquerque, NM (United States)

    2015-01-15

    The Rayleigh-Taylor instability causes mixing in plasmas throughout the universe, from micron-scale plasmas in inertial confinement fusion implosions to parsec-scale supernova remnants. The evolution of this interchange instability in a plasma is influenced by the presence of viscosity and magnetic fields, both of which have the potential to stabilize short-wavelength modes. Very few experimental observations of Rayleigh-Taylor growth in plasmas with stabilizing mechanisms are reported in the literature, and those that are reported are in sub-millimeter scale plasmas that are difficult to diagnose. Experimental observations in well-characterized plasmas are important for validation of computational models used to make design predictions for inertial confinement fusion efforts. This dissertation presents observations of instability growth during the interaction between a high Mach-number, initially un-magnetized plasma jet and a stagnated, magnetized plasma. A multi-frame fast camera captures Rayleigh-Taylor-instability growth while interferometry, spectroscopy, photodiode, and magnetic probe diagnostics are employed to estimate plasma parameters in the vicinity of the collision. As the instability grows, an evolution to longer mode wavelength is observed. Comparisons of experimental data with idealized magnetohydrodynamic simulations including a physical viscosity model suggest that the observed instability evolution is consistent with both magnetic and viscous stabilization. These data provide the opportunity to benchmark computational models used in astrophysics and fusion research.

  18. Rayleigh-Taylor-instability evolution in colliding-plasma-jet experiments with magnetic and viscous stabilization

    Energy Technology Data Exchange (ETDEWEB)

    Adams, Colin Stuart [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Univ. of New Mexico, Albuquerque, NM (United States); Univ. of Washington, Seattle, WA (United States)

    2015-01-15

    The Rayleigh-Taylor instability causes mixing in plasmas throughout the universe, from micron-scale plasmas in inertial confinement fusion implosions to parsec-scale supernova remnants. The evolution of this interchange instability in a plasma is influenced by the presence of viscosity and magnetic fields, both of which have the potential to stabilize short-wavelength modes. Very few experimental observations of Rayleigh-Taylor growth in plasmas with stabilizing mechanisms are reported in the literature, and those that are reported are in sub-millimeter scale plasmas that are difficult to diagnose. Experimental observations in well-characterized plasmas are important for validation of computational models used to make design predictions for inertial confinement fusion efforts. This dissertation presents observations of instability growth during the interaction between a high Mach-number, initially un-magnetized plasma jet and a stagnated, magnetized plasma. A multi-frame fast camera captures Rayleigh-Taylor-instability growth while interferometry, spectroscopy, photodiode, and magnetic probe diagnostics are employed to estimate plasma parameters in the vicinity of the collision. As the instability grows, an evolution to longer mode wavelength is observed. Comparisons of experimental data with idealized magnetohydrodynamic simulations including a physical viscosity model suggest that the observed instability evolution is consistent with both magnetic and viscous stabilization. These data provide the opportunity to benchmark computational models used in astrophysics and fusion research.

  19. Experimental investigation of photoresist etching by kHz AC atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lijun, E-mail: lijunwang@mail.xjtu.edu.cn; Zheng, Yashuang; Wu, Chen; Jia, Shenli

    2016-11-01

    Graphical abstract: Pin-ring electrode, double-ring electrode and multi-electrode kHz AC atmospheric pressure plasma jet were used to etch PR on Si wafer, and a corresponding parametric study was carefully investigated. Display Omitted - Highlights: • The surface roughness increases dramatically after APPJ treatment. • The etch rate of the pin-ring electrode APPJ is the highest than that of the multi-electrode APPJ and the double-ring electrode APPJ. • Ar APPJ has a much higher etch rate and more irregular etch trace than He APPJ. • The effective etching initially increases and then decreases with the increment of plasma jet outlet to PR surface distance. - Abstract: In this study, the mechanism of the photoresist (PR) etching by means of a kHz AC atmospheric pressure plasma jet (APPJ) is investigated. The scanning electron (SEM) and the polarizing microscope are used to perform the surface analysis, and the mechanical profilometry is applied to diagnose the etch rate. The results show that granulated structure with numerous microparticles appears at the substrate surface after APPJ treatment, and the etch rate in the etch center is the fastest and gradually slows down to the edge of etch region. In addition, the pin-ring electrode APPJ has the highest etch rate at but easy to damage the Si wafer, the double-ring APPJ is the most stable but requires long time to achieve the ideal etch result, and the etch rate and the etch result of the multi-electrode APPJ fall in between. Ar APPJ had much higher PR etch rate and more irregular etch trace than He APPJ. It is speculated that Ar APPJ is more energetic and effective in transferring reactive species to the PR surface. It is also observed that the effective etch area initially increases and then decreases as plasma jet outlet to the PR surface distance increases.

  20. Langmuir probe diagnostics of an atmospheric pressure, vortex-stabilized nitrogen plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Prevosto, L.; Mancinelli, B. R. [Grupo de Descargas Electricas, Departamento Ingenieria Electromecanica, Facultad Regional Venado Tuerto (UTN), Laprida 651, (2600) Venado Tuerto, Santa Fe (Argentina); Kelly, H. [Grupo de Descargas Electricas, Departamento Ingenieria Electromecanica, Facultad Regional Venado Tuerto (UTN), Laprida 651, (2600) Venado Tuerto, Santa Fe (Argentina) and Instituto de Fisica del Plasma (CONICET), Departamento de Fisica, Facultad de Ciencias Exactas y Naturales UBA Ciudad Universitaria Pab. I, (1428) Buenos Aires (Argentina)

    2012-09-15

    Langmuir probe measurements in an atmospheric pressure direct current (dc) plasma jet are reported. Sweeping probes were used. The experiment was carried out using a dc non-transferred arc torch with a rod-type cathode and an anode of 5 mm diameter. The torch was operated at a nominal power level of 15 kW with a nitrogen flow rate of 25 Nl min{sup -1}. A flat ion saturation region was found in the current-voltage curve of the probe. The ion saturation current to a cylindrical probe in a high-pressure non local thermal equilibrium (LTE) plasma was modeled. Thermal effects and ionization/recombination processes inside the probe perturbed region were taken into account. Averaged radial profiles of the electron and heavy particle temperatures as well as the electron density were obtained. An electron temperature around 11 000 K, a heavy particle temperature around 9500 K and an electron density of about 4 Multiplication-Sign 10{sup 22} m{sup -3}, were found at the jet centre at 3.5 mm downstream from the torch exit. Large deviations from kinetic equilibrium were found throughout the plasma jet. The electron and heavy particle temperature profiles showed good agreement with those reported in the literature by using spectroscopic techniques. It was also found that the temperature radial profile based on LTE was very close to that of the electrons. The calculations have shown that this method is particularly useful for studying spraying-type plasma jets characterized by electron temperatures in the range 9000-14 000 K.

  1. Treatment of Candida albicans biofilms with low-temperature plasma induced by dielectric barrier discharge and atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Koban, Ina; Welk, Alexander; Meisel, Peter; Holtfreter, Birte; Kocher, Thomas [Unit of Periodontology, Dental School, University of Greifswald, Rotgerberstr. 8, 17475 Greifswald (Germany); Matthes, Rutger; Huebner, Nils-Olaf; Kramer, Axel [Institute for Hygiene and Environmental Medicine, University of Greifswald, Walther-Rathenau-Str. 49 a, 17487 Greifswald (Germany); Sietmann, Rabea [Institute of Microbiology, University of Greifswald, Friedrich-Ludwig-Jahn-Str. 15, 17487 Greifswald (Germany); Kindel, Eckhard; Weltmann, Klaus-Dieter, E-mail: ina.koban@uni-greifswald.d [Leibniz Institute for Plasma Science and Technology (INP), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

    2010-07-15

    Because of some disadvantages of chemical disinfection in dental practice (especially denture cleaning), we investigated the effects of physical methods on Candida albicans biofilms. For this purpose, the antifungal efficacy of three different low-temperature plasma devices (an atmospheric pressure plasma jet and two different dielectric barrier discharges (DBDs)) on Candida albicans biofilms grown on titanium discs in vitro was investigated. As positive treatment controls, we used 0.1% chlorhexidine digluconate (CHX) and 0.6% sodium hypochlorite (NaOCl). The corresponding gas streams without plasma ignition served as negative treatment controls. The efficacy of the plasma treatment was determined evaluating the number of colony-forming units (CFU) recovered from titanium discs. The plasma treatment reduced the CFU significantly compared to chemical disinfectants. While 10 min CHX or NaOCl exposure led to a CFU log{sub 10} reduction factor of 1.5, the log{sub 10} reduction factor of DBD plasma was up to 5. In conclusion, the use of low-temperature plasma is a promising physical alternative to chemical antiseptics for dental practice.

  2. Increase of the Density, Temperature and Velocity of Plasma Jets driven by a Ring of High Energy Laser Beams

    OpenAIRE

    Fu, Wen; Liang, Edison P.; Fatenejad, Milad; Lamb, Donald Q.; Grosskopf, Michael; Park, Hye-Sook; Remington, Bruce; Spitkovsky, Anatoly

    2012-01-01

    Supersonic plasma outflows driven by multi-beam, high-energy lasers, such as Omega and NIF, have been and will be used as platforms for a variety of laboratory astrophysics experiments. Here we propose a new way of launching high density and high velocity, plasma jets using multiple intense laser beams in a hollow ring formation. We show that such jets provide a more flexible and versatile platform for future laboratory astrophysics experiments. Using high resolution hydrodynamic simulations,...

  3. Observation of Periodic Multiplication and Chaotic Phenomena in Atmospheric Cold Plasma Jets

    Institute of Scientific and Technical Information of China (English)

    QI Bing; HUANG Jian-Jun; ZHANG Zhe-Huang; WANG De-Zhen

    2008-01-01

    We investigate the temporal evolution of the current pulses from an ac He cold plasma jet at atmospheric pressure and with driving frequency in the range 14.76-15.30 kHz. The driving frequency is used as the plasma system's bifurcation parameter in analogy with the evolution in which the current pulses undergoes multiplication and chaos. Such time-domain nonlinearity is important for controlling instabilities in atmospheric glow discharges.In addition, the observation can provide some data to support the simulation results reported previously [Appl.Phys. Lett. 90 (2007) 071501].

  4. LIF diagnostics of hydroxyl radical in a methanol containing atmospheric-pressure plasma jet

    Science.gov (United States)

    Qian, Mu-Yang; Liu, San-Qiu; Pei, Xue-Kai; Lu, Xin-Pei; Zhang, Jia-Liang; Wang, De-Zhen

    2016-10-01

    In this paper, a pulsed-dc CH3OH/Ar plasma jet generated at atmospheric pressure is studied by laser-induced fluorescence (LIF) and optical emission spectroscopy (OES). A gas-liquid bubbler system is proposed to introduce the methanol vapor into the argon gas, and the CH3OH/Ar volume ratio is kept constant at about 0.1%. Discharge occurs in a 6-mm needle-to-ring gap in an atmospheric-pressure CH3OH/Ar mixture. The space-resolved distributions of OH LIF inside and outside the nozzle exhibit distinctly different behaviors. And, different production mechanisms of OH radicals in the needle-to-ring discharge gap and afterglow of plasma jet are discussed. Besides, the optical emission lines of carbonaceous species, such as CH, CN, and C2 radicals, are identified in the CH3OH/Ar plasma jet. Finally, the influences of operating parameters (applied voltage magnitude, pulse frequency, pulsewidth) on the OH radical density are also presented and analyzed. Project supported by the National Natural Science Foundation of China (Grant Nos. 11465013 and 11375041), the Natural Science Foundation of Jiangxi Province, China (Grant Nos. 20151BAB212012 and 20161BAB201013), and the International Science and Technology Cooperation Program of China (Grant No. 2015DFA61800).

  5. Denitrogenation and desulphurization during hydropyrolysis of coal in H{sub 2}/Ar plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Bao, W.; Zhang, J.; Shen, S.; Cao, Q.; Lu, Y. [Taiyuan University of Technology, Taiyuan (China)

    2007-03-15

    The denitrogenation and desulphurization during hydropyrolysis of six Chinese coals were systematically investigated in H{sub 2}/Ar plasma jet. The results from experiments show that HCN is the main product of coal-N at high temperature. Only a low amount of NH{sub 3} is formed. Yield of HCN depends on coal types and coal feeding rate, but NH{sub 3} does not change obviously. Yields of HCN and NH{sub 3} decrease with the increase of oxygen contents in coal during hydropyrolysis in H{sub 2}/Ar plasma jet. The change of feeding rate affects the formation of H{sub 2}S from the conversion of coal-S. The mole ratios of n(N)/n(C) and n(S)/n(C) in all char samples are less than that of coal. The results suggest that hydropyrolysis in H{sub 2}/Ar plasma jet is an efficient method for denitrogenation and desulphurization. In the present experimental conditions, the denitrogenation and desulphurization percentages reach up to 50% and 55% for Yanzhou coal, respectively. Yima coal can reach up to 40% and 60%. 11 refs., 3 figs., 3 tabs.

  6. Surface conductivity dependent dynamic behaviour of an ultrafine atmospheric pressure plasma jet for microscale surface processing

    Science.gov (United States)

    Abuzairi, Tomy; Okada, Mitsuru; Bhattacharjee, Sudeep; Nagatsu, Masaaki

    2016-12-01

    An experimental study on the dynamic behaviour of microcapillary atmospheric pressure plasma jets (APPJs) with 5 μm tip size for surfaces of different conductivity is reported. Electrical and spatio-temporal characteristics of the APPJs are monitored using high voltage probe, current monitor and high speed intensified charge couple device camera. From these experimental results, we presented a simple model to understand the electrical discharge characteristics of the capillary APPJs with double electrodes, and estimated the velocity of the ionization fronts in the jet and the electron density to be 3.5-4.2 km/s and 2-7 × 1017 m-3. By analyzing the dynamics of the microcapillary APPJs for different substrate materials, it was found that the surface irradiation area strongly depended on the substrate conductivity and permittivity, especially in the case of polymer-like substrate, surface irradiation area was significantly broadened probably due to the repelling behaviour of the plasma jets from the accumulated electrical charges on the polymer surface. The effect of applying a substrate bias in the range from -900 V to +900 V on the plasma irradiation onto the substrates was also investigated. From the knowledge of the present results, it is helpful for choosing the substrate materials for microscale surface modification.

  7. Power dissipated in a non-thermal atmospheric pressure plasma jet measured by miniaturized electrical probes

    Science.gov (United States)

    Golda, Judith; Schulz-von der Gathen, Volker

    2016-09-01

    Non-thermal atmospheric pressure plasma jets are used in bio-medicine, because they generate reactive species at a low gas temperature. Knowledge and control of plasma parameters is required for stable and reliable operation. Therefore, measuring dissipated power in these plasmas is necessary. However, this is challenging because the delivered sender power is often orders of magnitudes higher than the power dissipated in the discharge itself. To measure this dissipated power, we built miniaturized electrical probes directly attached to the jet device. We observed that the dissipated power is a more comprehensive parameter than the common parameter voltage: For example, gas temperature and emission line intensities rose exponentially with increasing voltage but linearly with increasing power. Our analyses further revealed that a substantial proportion of the dissipated power is transformed into heat. In conclusion, miniaturized electrical probes give a fundamental insight into the energy balance of atmospheric pressure plasmas. In the future, these probes can also be adapted to different types of atmospheric pressure plasmas. This work was supported by DFG within the frameworks of the Package Project PAK 816.

  8. Emission spectroscopy of an atmospheric pressure plasma jet operated with air at low frequency

    Science.gov (United States)

    Giuliani, L.; Gallego, J. L.; Minotti, F.; Kelly, H.; Grondona, D.

    2015-03-01

    Low-temperature, high-pressure plasma jets have an extensive use in plasma biology and plasma medicine, such as pathogen deactivation, wound disinfection, stopping of bleeding without damage of healthy tissue, acceleration of wound healing, control of bio-film proliferation, etc. In this work, a spectroscopic characterization of a typical plasma jet, operated in air at atmospheric pressure, is reported. Within the spectrum of wavelengths from 200 to 450 nm all remarkable emissions of N2 were monitored. Spectra of the N2 2nd positive system (C3Πu-B3Πg) emitted in air are the most convenient for plasma diagnostics, since they enable to determine electronic Te, rotational Tr and vibrational Tv temperatures by fitting the experimental spectra with the simulated ones. We used SPECAIR software for spectral simulation and obtained the best fit with all these temperatures about 3500K. The conclusion that all temperatures are equal, and its relatively high value, is consistent with the results of a previous work, where it was found that the experimentally determined electrical characteristic was consistent with the model of a thermal arc discharge, together with a highly collisional cathode sheet.

  9. Impurity induced neutralization of MeV energy protons in JET plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Gondhalekar, A. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Korotkov, A.A. [AF Ioffe Institute, Saint Petersburg (Russian Federation)

    1994-07-01

    A model elucidating the role of carbon and beryllium, the main impurities in JET plasmas, in neutralizing MeV energy protons, which arise during ICRF heating of deuterium plasmas in the hydrogen minority heating mode D(H), and from D-D fusion reactions, is presented. The model establishes charge transfer from hydrogen-like impurity ions to protons as the main process for neutralization. Calculations for deducing the proton energy distribution function from measured hydrogen flux are described. The validity of the model is tested by using it to described the measured flux in different conditions of plasma heating and fueling. Further, it is used to deduce the background thermal deuterium atom density at the plasma center. 9 refs., 6 figs.

  10. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage

    Science.gov (United States)

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-01-01

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction. PMID:27759080

  11. Improved performance of a barrier-discharge plasma jet biased by a direct-current voltage

    Science.gov (United States)

    Li, Xuechen; Li, Yaru; Zhang, Panpan; Jia, Pengying; Dong, Lifang

    2016-10-01

    One of the challenges that plasma research encounters is how to generate a large-scale plasma plume at atmospheric pressure. Through utilizing a third electrode biased by a direct-current voltage, a longer plasma plume is generated by a plasma jet in dielectric barrier discharge configurations. Results indicate that the plume length increases until it reaches the third electrode with increasing the bias voltage. By fast photography, it is found that the plume consists of two types of streamers under the influence of the bias voltage, which develops from a guided streamer to a branching one with leaving the tube opening. The transition from the guided streamer to the branching one can be attributed to the electric field and the air/argon fraction.

  12. RF Pre-Ionization to Create Faster, Hotter MHD-Driven Jets and Studies of Plasma Expansion Into a Vacuum

    Science.gov (United States)

    Chaplin, Vernon; Bellan, Paul

    2013-10-01

    We are studying MHD-driven jets relevant to astrophysical jets and fusion plasmas. Previous experiments at Caltech have focused on plasmas created by breaking down neutral gas using high voltage. The Paschen breakdown criterion governing this process sets an undesirable lower limit for the jet density. To overcome this constraint, we have developed a pre-ionization system powered by a pulsed, battery-powered, 3 kW 13.56 MHz RF amplifier. Pre-ionization of plasma in a tube behind the jet experiment's center electrode is expected to enable the formation of lower density, hotter, faster jets. Thus far, argon jets have been created with v >30 km/s, twice as fast as was previously achievable. The expansion of the RF plasma into the chamber prior to the discharge of the main capacitor bank involves surprisingly complex dynamics. There are two phases: initially plasma expansion along the background magnetic field is inhibited and the primary source of emission away from the RF antenna appears to be neutral atoms excited by fast electrons or photons from the RF source. At a later time, either before or after RF turn-off depending on the magnetic field configuration, a relatively high density (ne >1018 m-3) , cold (Te < 0.5 eV) cloud of plasma emerges from the source tube.

  13. Ion temperature and toroidal rotation in JET's low torque plasmas

    Science.gov (United States)

    Bernardo, J.; Nave, M. F. F.; Giroud, C.; Reyes Cortes, S.; Bizarro, João P. S.

    2016-11-01

    This paper reports on the procedure developed as the best method to provide an accurate and reliable estimation of the ion temperature Ti and the toroidal velocity vϕ from Charge-eXchange Recombination Spectroscopy (CXRS) data from intrinsic rotation experiments at the Joint European Torus with the carbon wall. The low impurity content observed in such plasmas, resulting in low active CXRS signal, alongside low Doppler shifts makes the determination of Ti and vϕ particularly difficult. The beam modulation method will be discussed along with the measures taken to increase photon statistics and minimise errors from the absolute calibration and magneto-hydro-dynamics effects that may impact the CXRS passive emission.

  14. Verification of the plasma diffusion-wave propagation in an atmospheric-pressure plasma jet with the solution of a diffusion equation

    Science.gov (United States)

    Cho, Guangsup; Uhm, Han Sup

    2016-10-01

    The time-dependent solution of diffusion equation by the Fourier integration provides the axial diffusion velocity of a plasma packet, which is a key element of the plasma propagation in a plasma jet operated by the several tens of kHz. The plasma diffusion velocity is higher than the order of un ˜ 10 m/s at a high electric-field region of plasma generation and it is about the order of un ˜ 10 m/s at the plasma column of a low field region in a jet-nozzle inside. Meanwhile, the diffusion velocity is slower than the order of un ˜ 10 m/s in the open-air space where the plasma density flattens due to its radial expansion. Using these diffusion velocity data, the group-velocity of plasma diffusion wave-packet is given by ug ˜ cs2/un, a combination of the diffusion velocity un and the acoustic velocity cs. The experimental results of the plasma propagation can be verified with the plasma propagation in a form of the wave-packet whose propagation velocity is 104 m/s in a tube inside and is as fast as 105 m/s in the open-air space, thereby reconfirming that the theory of a plasma diffusion-wave is the origin of the plasma propagation in a plasma jet.

  15. Impact of plasma jet vacuum ultraviolet radiation on reactive oxygen species generation in bio-relevant liquids

    Energy Technology Data Exchange (ETDEWEB)

    Jablonowski, H.; Hammer, M. U.; Reuter, S. [Center for Innovation Competence plasmatis, Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Leibniz Institute for Plasma Science and Technology, INP Greifswald e.V. Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Bussiahn, R.; Weltmann, K.-D.; Woedtke, Th. von [Leibniz Institute for Plasma Science and Technology, INP Greifswald e.V. Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

    2015-12-15

    Plasma medicine utilizes the combined interaction of plasma produced reactive components. These are reactive atoms, molecules, ions, metastable species, and radiation. Here, ultraviolet (UV, 100–400 nm) and, in particular, vacuum ultraviolet (VUV, 10–200 nm) radiation generated by an atmospheric pressure argon plasma jet were investigated regarding plasma emission, absorption in a humidified atmosphere and in solutions relevant for plasma medicine. The energy absorption was obtained for simple solutions like distilled water (dH{sub 2}O) or ultrapure water and sodium chloride (NaCl) solution as well as for more complex ones, for example, Rosewell Park Memorial Institute (RPMI 1640) cell culture media. As moderate stable reactive oxygen species, hydrogen peroxide (H{sub 2}O{sub 2}) was studied. Highly reactive oxygen radicals, namely, superoxide anion (O{sub 2}{sup •−}) and hydroxyl radicals ({sup •}OH), were investigated by the use of electron paramagnetic resonance spectroscopy. All species amounts were detected for three different treatment cases: Plasma jet generated VUV and UV radiation, plasma jet generated UV radiation without VUV part, and complete plasma jet including all reactive components additionally to VUV and UV radiation. It was found that a considerable amount of radicals are generated by the plasma generated photoemission. From the experiments, estimation on the low hazard potential of plasma generated VUV radiation is discussed.

  16. Impact of plasma jet vacuum ultraviolet radiation on reactive oxygen species generation in bio-relevant liquids

    Science.gov (United States)

    Jablonowski, H.; Bussiahn, R.; Hammer, M. U.; Weltmann, K.-D.; von Woedtke, Th.; Reuter, S.

    2015-12-01

    Plasma medicine utilizes the combined interaction of plasma produced reactive components. These are reactive atoms, molecules, ions, metastable species, and radiation. Here, ultraviolet (UV, 100-400 nm) and, in particular, vacuum ultraviolet (VUV, 10-200 nm) radiation generated by an atmospheric pressure argon plasma jet were investigated regarding plasma emission, absorption in a humidified atmosphere and in solutions relevant for plasma medicine. The energy absorption was obtained for simple solutions like distilled water (dH2O) or ultrapure water and sodium chloride (NaCl) solution as well as for more complex ones, for example, Rosewell Park Memorial Institute (RPMI 1640) cell culture media. As moderate stable reactive oxygen species, hydrogen peroxide (H2O2) was studied. Highly reactive oxygen radicals, namely, superoxide anion (O2•-) and hydroxyl radicals (•OH), were investigated by the use of electron paramagnetic resonance spectroscopy. All species amounts were detected for three different treatment cases: Plasma jet generated VUV and UV radiation, plasma jet generated UV radiation without VUV part, and complete plasma jet including all reactive components additionally to VUV and UV radiation. It was found that a considerable amount of radicals are generated by the plasma generated photoemission. From the experiments, estimation on the low hazard potential of plasma generated VUV radiation is discussed.

  17. Ion Acceleration by Laser Plasma Interaction from Cryogenic Micro Jets - Oral Presentation

    Energy Technology Data Exchange (ETDEWEB)

    Propp, Adrienne [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-08-25

    Processes that occur in extreme conditions, such as in the center of stars and large planets, can be simulated in the laboratory using facilities such as SLAC National Accelerator Laboratory and the Jupiter Laser Facility (JLF) at Lawrence Livermore National Laboratory (LLNL). These facilities allow scientists to investigate the properties of matter by observing their interactions with high power lasers. Ion acceleration from laser plasma interaction is gaining greater attention today due to its widespread potential applications, including proton beam cancer therapy and fast ignition for energy production. Typically, ion acceleration is achieved by focusing a high power laser on thin foil targets through a mechanism called Target Normal Sheath Acceleration. Based on research and recent experiments, we hypothesized that a pure liquid cryogenic jet would be an ideal target for this type of interaction, capable of producing the highest proton energies possible with today’s laser technologies. Furthermore, it would provide a continuous, pure target, unlike metal foils which are consumed in the interaction and easily contaminated. In an effort to test this hypothesis and investigate new, potentially more efficient mechanisms of ion acceleration, we used the 527 nm split beam, frequency-doubled TITAN laser at JLF. Data from the cryogenic jets was limited due to the flow of current up the jet into the nozzle during the interaction, heating the jet and damaging the orifice. However, we acheived a pure proton beam with an indiciation of a monoenergetic feature. Furthermore, data from gold and carbon wires showed surprising and interesting results. Preliminary analysis of data from two ion emission diagnostics, Thomson parabola spectrometers (TPs) and radio chromic films (RCFs), suggests that shockwave acceleration occurred rather than target normal sheath acceleration, the standard mechanism of ion acceleration. Upon completion of the experiment at TITAN, I researched the

  18. Debris-free laser plasma sources for EUVL based on gas jets

    Energy Technology Data Exchange (ETDEWEB)

    Kubiak, G.D.; O`Connell, D.; Krenz, K.D.

    1996-03-01

    EUV sources for EUVL must not only be bright for throughput, they must also be debris-free to increase condenser longevity. Many schemes to achieve bright, clean sources for EUVL have been studied, including mass-limited targets, cryogenic targets, electric discharges, and electron-beam pumped vapor. Several of these sources show promise, with varying degrees of brightness, debris reduction, and system complexity. We have studied pulsed gas jets, which we find to be relatively simple, debris-free sources when used under appropriate conditions. Under transverse, 1.06 {mu}m irradiation of the jet at incident laser intensities in the range of 10{sup 11}-10{sup 12} Watts/cm{sup 2}, the conversion efficiency into 2{pi} steradians is in the range of 0.3-0.4%, or approximately half the value exhibited by solid Au or W targets under similar conditions. Source sizes in the range of 350 {mu}m x 400 {mu}m can be achieved, as shown in Fig. 2, depending sensitively on both laser and gas jet parameters. One issue that must be overcome in the use of gas jet targets is the requirement that the laser-irradiated plasma be located as far from the jet nozzle as possible to avoid debris generation while maintaining adequate EUV conversion. We will describe conditions under which these criteria are met. Measurements of the reflectance lifetimes of multilayer-coated mirrors placed near the plasma source under these conditions will also be presented. The potential for scaling such sources up to meet the requirements of a commercial EUVL system will be discussed.

  19. Optical properties of the atmospheric pressure helium plasma jet generated by alternative current (a.c.) power supply

    Science.gov (United States)

    Ilik, Erkan; Akan, Tamer

    2016-05-01

    In this work, an atmospheric pressure plasma jet (APPJ) was produced to generate cold flowing post-discharge plasma of pure helium gas. The main aim of this study was to generate cold flowing APPJ of pure helium gas and to determine how their optical emission spectrum change influences varying different flow rates. Lengths of early, middle, and late post-discharge plasma (jet) regions and their fluctuations were determined, respectively. Then, ignition condition dependence of the post-discharge plasma for flow rate was specified at a constant voltage. Spectroscopic studies of an atmospheric pressure plasma jet of helium were presented via analyzing OH, N2, N2+, oxygen, and helium intensities for various flow rates.

  20. Characterization of plasma jet ejected from a parallel-plate rail gun for simulating edge localized mode

    Energy Technology Data Exchange (ETDEWEB)

    Chung, K.S., E-mail: alsk3@snu.ac.kr; Chung, Kyoung-Jae, E-mail: jkjlsh1@snu.ac.kr; Jung, B.K.; Hwang, Y.S., E-mail: yhwang@snu.ac.kr

    2013-10-15

    Highlights: • A small plasma gun is constructed to study edge localized mode. • A plasma jet ejected from the gun is characterized with a quadruple Langmuir probe. • The device and diagnostics are suitable for research about the control of plasma jet. -- Abstract: A small plasma gun with parallel-plate configuration is fabricated to generate a bunch of plasma which is similar to ELM (edge localized mode) plasma, by taking advantages of its simplicity and cost-effectiveness. Prior to explore how to control the ELM-like plasma so as to relieve heat load on the divertor target, characteristics of a plasma jet ejected from the plasma gun are investigated using a quadruple Langmuir probe which is appropriate for measuring rapidly varying plasma parameters such as electron density, temperature, and ion velocity at the same time. The plasma density and ion velocity measured at 112 mm away from the exit are 3 × 10{sup 19} m{sup −3} and 11 km/s, respectively, which seem to be suitable for investigating next step research on the control of ELM-like plasma using various methods such as electromagnetic waves and high-voltage pulses. Also, the quadruple Langmuir probe is proven to be adequate for use in such experiments.

  1. Laser-optical measurements of the velocities of the plasma jets formed from different gases in a kilojoule-range plasma focus facility

    Energy Technology Data Exchange (ETDEWEB)

    Polukhin, S. N., E-mail: snpol@lebedev.ru; Dzhamankulov, A. M.; Gurei, A. E.; Nikulin, V. Ya., E-mail: vnik@lebedev.ru; Peregudova, E. N.; Silin, P. V. [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation)

    2016-12-15

    The velocities of the plasma jets formed from Ne, N{sub 2}, Ar, and Xe gases in plasma focus facilities were determined by means of laser-optical shadowgraphy of the shock waves generated at the jet leading edge. In spite of the almost tenfold ratio between the atomic weights of these gases, the outflow velocities of the plasma jets formed in experiments with these gases differ by less than twice, in the range of (0.7–1.1) × 10{sup 7} cm/s under similar discharge conditions. The energies of the jet ions were found to vary from 0.7 keV for nitrogen to 4 keV for xenon.

  2. Microwave atmospheric pressure plasma jets for wastewater treatment: Degradation of methylene blue as a model dye.

    Science.gov (United States)

    García, María C; Mora, Manuel; Esquivel, Dolores; Foster, John E; Rodero, Antonio; Jiménez-Sanchidrián, César; Romero-Salguero, Francisco J

    2017-08-01

    The degradation of methylene blue in aqueous solution as a model dye using a non thermal microwave (2.45 GHz) plasma jet at atmospheric pressure has been investigated. Argon has been used as feed gas and aqueous solutions with different concentrations of the dye were treated using the effluent from plasma jet in a remote exposure. The removal efficiency increased as the dye concentration decreased from 250 to 5 ppm. Methylene blue degrades after different treatment times, depending on the experimental plasma conditions. Thus, kinetic constants up to 0.177 min(-1) were obtained. The higher the Ar flow, the faster the degradation rate. Optical emission spectroscopy (OES) was used to gather information about the species present in the gas phase, specifically excited argon atoms. Argon excited species and hydrogen peroxide play an important role in the degradation of the dye. In fact, the conversion of methylene blue was directly related to the density of argon excited species in the gas phase and the concentration of hydrogen peroxide in the aqueous liquid phase. Values of energy yield at 50% dye conversion of 0.296 g/kWh were achieved. Also, the use of two plasma applicators in parallel has been proven to improve energy efficiency. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Stabilization of sawteeth with third harmonic deuterium ICRF-accelerated beam in JET plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Girardo, Jean-Baptiste [EUROfusion Consortium, JET, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Sharapov, Sergei; Fitzgerald, Michael; Hawkes, Nick; Kiptily, Vasily; Lupelli, Ivan [CCFE, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Boom, Jurrian [Max-Planck-Institut für Plasmaphysik, 85748 Garching (Germany); Dumont, Rémi; Garbet, Xavier; Sarazin, Yanick; Schneider, Mireille [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Eriksson, Jacob [Department of Physics and Astronomy, Uppsala University, 751 20 Uppsala (Sweden); Mantsinen, Mervi [Catalan Institution for Research and Advanced Studies, 08010 Barcelona (Spain); Barcelona Supercomputing Center, 08034 Barcelona (Spain)

    2016-01-15

    Sawtooth stabilisation by fast ions is investigated in deuterium (D) and D-helium 3 (He3) plasmas of JET heated by deuterium Neutral Beam Injection combined in synergy with Ion Cyclotron Resonance Heating (ICRH) applied on-axis at 3rd beam cyclotron harmonic. A very significant increase in the sawtooth period is observed, caused by the ICRH-acceleration of the beam ions born at 100 keV to the MeV energy range. Four representative sawteeth from four different discharges are compared with Porcelli's model. In two discharges, the sawtooth crash appears to be triggered by core-localized Toroidal Alfvén Eigenmodes inside the q = 1 surface (also called “tornado” modes) which expel the fast ions from within the q = 1 surface, over time scales comparable with the sawtooth period. Two other discharges did not exhibit fast ion-driven instabilities in the plasma core, and no degradation of fast ion confinement was found in both modelling and direct measurements of fast ion profile with the neutron camera. The developed sawtooth scenario without fast ion-driven instabilities in the plasma core is of high interest for the burning plasmas. Possible causes of the sawtooth crashes on JET are discussed.

  4. [Investigation on the electron density of a micro-plasma jet operated at atmospheric pressure].

    Science.gov (United States)

    Li, Xue-chen; Zhao, Na; Liu, Wei-yuan; Liu, Zhi-qiang

    2010-07-01

    In the present paper, a micro-hollow cathode discharge setup was used to generate micro-plasma jet in flowing mixture of Ar and N2 at atmospheric pressure. The characteristics of the micro-plasma jet were investigated by means of optical method and electrical one. It has been found that breakdown occurs in the gas between the two electrodes when the input power of electric source is increased to a certain value. Plasma appears along the gas flow direction when the mixed gas flows from the aperture of the micro-hollow cathode, and the length of plasma reaches 4 mm. The discharge current is quasi-continuous, and the duration of discharge pulse is about 0.1 micros. Electron density was studied by using Einstein equation and Stark broadening of spectral lines from the emission spectrum respectively. It was found that the results of electron density calculated by the two methods are consistent with the order of 10(15) x cm(-3). It was also found that the electron density is almost independent of power. A qualitative explanation to the phenomenon is given based on the gas discharge theory.

  5. On the Role of Metastable Argon in Cold Atmospheric Pressure Plasma Jets with Shielding Gas Device

    Science.gov (United States)

    Schmidt-Bleker, Ansgar; Winter, Jorn; Sousa, Joao Santos; Puech, Vincent; Weltmann, Klaus-Dieter; Reuter, Stephan; ZIK plasmatis at the INP Greifswald e. V. Team; Laboratoire de Physique des Gaz et des Plasmas (LPGP), CNRS; Université Paris-Sud Team

    2014-10-01

    Shielding gas devices are a valuable tool for controlling the reactive species output of Cold Atmospheric Pressure Plasma (CAPP) Jets for biomedical applications. In this work we investigate the effect of different shielding gas compositions using a CAPP jet (kinpen) operated with argon. As shielding gas various mixtures of N2 and O2 are used. Metastable argon (Ar*) has been quantified using laser absorption spectroscopy and was identified as an important energy carrier in the CAPP jets effluent. The Ar* excitation dynamics was studied using phase resolve optical emission spectroscopy. Based on these findings a kinetic model for the gas phase chemistry has been developed that uses the Ar* density and dynamics as input and yields densities of O3, NO2, HNO2, HNO3, N2O5, H2O2 and N2O produced by the CAPP jet for different shielding gas compositions. The results are in good agreement with Fourier-Transform Infrared Spectroscopy measurements on these species. Authors gratefully acknowledge the funding by German Federal Ministry of Education a Research (BMBF) (Grant # 03Z2DN12).

  6. Improvement of stability of sinusoidally driven atmospheric pressure plasma jet using auxiliary bias voltage

    Directory of Open Access Journals (Sweden)

    Hyun-Jin Kim

    2015-12-01

    Full Text Available In this study, we have proposed the auxiliary bias pulse scheme to improve the stability of atmospheric pressure plasma jets driven by an AC sinusoidal waveform excitation source. The stability of discharges can be significantly improved by the compensation of irregular variation in memory voltage due to the effect of auxiliary bias pulse. From the parametric study, such as the width, voltage, and onset time of auxiliary bias pulse, it has been demonstrated that the auxiliary bias pulse plays a significant role in suppressing the irregular discharges caused by the irregular variation in memory voltage and stable discharge can be initiated with the termination of the auxiliary bias pulse. As a result of further investigating the effects of the auxiliary pulse scheme on the jet stability under various process conditions such as the distance between the jet head and the counter electrode, and carrier gas flow, the jet stability can be improved by adjusting the amplitude and number of the bias pulse depending on the variations in the process conditions.

  7. Effect of atmospheric pressure plasma jet on the foodborne pathogens attached to commercial food containers.

    Science.gov (United States)

    Kim, Hyun-Joo; Jayasena, Dinesh D; Yong, Hae In; Alahakoon, Amali U; Park, Sanghoo; Park, Jooyoung; Choe, Wonho; Jo, Cheorun

    2015-12-01

    Bacterial biofilms are associated with numerous infections and problems in the health care and food industries. The aim of this study was to evaluate the bactericidal effect of an atmospheric pressure plasma (APP) jet on Escherichia coli O157:H7, Listeria monocytogenes, and Salmonella Typhimurium biofilm formation on collagen casing (CC), polypropylene (PP) and polyethylene terephthalate (PET), which are widely used food container materials. The samples were treated separately with the APP jet at a 50-W input power for 5 and 10 min, and nitrogen (6 l per minute) gas combined with oxygen (10 standard cubic centimeters per minute) was used to produce the APP. The APP jet reduced the number of bacterial cells in a time-dependent manner. All pathogens attached to CC, PP, and PET were reduced by 3-4 log CFU/cm(2) by the 10-min APP treatment. The developed APP jet was effectively reduced biofilms on CC, PP, and PET.

  8. Magnetic field generation in a jet-sheath plasma via the kinetic Kelvin-Helmholtz instability

    Directory of Open Access Journals (Sweden)

    K.-I. Nishikawa

    2013-09-01

    Full Text Available We have investigated the generation of magnetic fields associated with velocity shear between an unmagnetized relativistic jet and an unmagnetized sheath plasma. We have examined the strong magnetic fields generated by kinetic shear (Kelvin–Helmholtz instabilities. Compared to the previous studies using counter-streaming performed by Alves et al. (2012, the structure of the kinetic Kelvin–Helmholtz instability (KKHI of our jet-sheath configuration is slightly different, even for the global evolution of the strong transverse magnetic field. In our simulations the major components of growing modes are the electric field Ez, perpendicular to the flow boundary, and the magnetic field By, transverse to the flow direction. After the By component is excited, an induced electric field Ex, parallel to the flow direction, becomes significant. However, other field components remain small. We find that the structure and growth rate of KKHI with mass ratios mi/me = 1836 and mi/me = 20 are similar. In our simulations saturation in the nonlinear stage is not as clear as in counter-streaming cases. The growth rate for a mildly-relativistic jet case (γj = 1.5 is larger than for a relativistic jet case (γj = 15.

  9. Experimental analysis of DBD plasma jet properties using different gases and two kinds of transfer plate

    CERN Document Server

    Nascimento, Fellype do; Machida, Munemasa

    2015-01-01

    Dielectric Barrier Discharge (DBD) plasma jets has been studied extensively in recent years because of its wide range of applications. DBD plasmas can be produced using many different gases and can be applied to a broad variety of surfaces and substrates. In this work, we provide a comparison of DBD plasmas generated using argon (Ar), helium (He) and nitrogen (N2), as well as their mixtures with water vapor in order to know how some plasma properties are affected by the use of different gases. All plasmas were studied in two different conditions, using a transfer plate made of a conductive material and using a transfer plate made of an insulating one. We observed that the processes of excitation and ionization of nitrogen molecules by direct collisions with Ar or He are more evident and significant in He plasmas, which means that He atoms in metastable states have greater ability to transfer energy to molecules of nitrogen in the plasma. The collisions of He atoms in metastable states with N2 molecules determ...

  10. Comparison of platelet rich plasma and synthetic graft material for bone regeneration after third molar extraction

    Science.gov (United States)

    Nathani, Dipesh B.; Sequeira, Joyce; Rao, B. H. Sripathi

    2015-01-01

    Aims: To compare the efficacy of Platelet rich plasma and synthetic graft material for bone regeneration after bilateral third molar extraction. Material and Methods: This study was conducted in 10 patients visiting the outpatient department of Oral & Maxillofacial Surgery, Yenepoya Dental College & Hospital. Patients requiring extraction of bilateral mandibular third molars were taken for the study. Following extraction, PRP (Platelet Rich Plasma) was placed in one extraction socket and synthetic graft material in form granules [combination of Hydroxyapatite (HA) and Bioactive glass (BG)] in another extraction socket. The patients were assessed for postoperative pain and soft tissue healing. Radiological assessment of the extraction site was done at 8, 12 and 16 weeks interval to compare the change in bone density in both the sockets. Results: Pain was less on PRP site when compared to HA site. Soft tissue evaluation done using gingival healing index given by Landry et al showed better healing on PRP site when compared to HA site. The evaluation of bone density by radiological assessment showed the grey level values calculated at 4 months at the PRP site were comparatively higher than HA site. Conclusion: The study showed that the platelet rich plasma is a better graft material than synthetic graft material in terms of soft tissue and bone healing. However a more elaborate study with a larger number of clinical cases is very much essential to be more conclusive regarding the efficacy of both the materials. PMID:26981473

  11. Long wavelength perfect fluidity from short distance jet transport in quark-gluon plasmas

    CERN Document Server

    Xu, Jiechen; Gyulassy, Miklos

    2015-01-01

    We build a new phenomenological framework that bridges the long wavelength bulk viscous transport properties of the strongly-coupled quark-gluon plasma (sQGP) and short distance hard jet transport properties in the QGP. The full nonperturbative chromo-electric (E) and chromo-magnetic (M) structure of the near "perfect fluid" like sQGP in the critical transition region are integrated into a semi-Quark-Gluon-Monopole Plasma (sQGMP) model lattice-compatibly and implemented into the new CUJET3.0 jet quenching framework. All observables computed from CUJET3.0 are found to be consistent with available data at RHIC and LHC simultaneously. A quantitative connection between the shear viscosity and jet transport parameter is rigorously established within this framework. We deduce the $T=160-600$ MeV dependence of the QGP's $\\eta/s$: its near vanishing value in the near $T_c$ regime is determined by the composition of E and M charges, it increases as $T$ rises, and its high $T$ limit is fixed by color screening scales.

  12. Hard X-Ray Burst Detected From Caltech Plasma Jet Experiment Magnetic Reconnection Event

    Science.gov (United States)

    Marshall, Ryan S.; Bellan, Paul M.

    2016-10-01

    In the Caltech plasma jet experiment a 100 kA MHD driven jet becomes kink unstable leading to a Rayleigh-Taylor instability that quickly causes a magnetic reconnection event. Movies show that the Rayleigh-Taylor instability is simultaneous with voltage spikes across the electrodes that provide the current that drives the jet. Hard x-rays between 4 keV and 9 keV have now been observed using an x-ray scintillator detector mounted just outside of a kapton window on the vacuum chamber. Preliminary results indicate that the timing of the x-ray burst coincides with a voltage spike on the electrodes occurring in association with the Rayleigh-Taylor event. The x-ray signal accompanies the voltage spike and Rayleigh-Taylor event in approximately 50% of the shots. A possible explanation for why the x-ray signal is sometimes missing is that the magnetic reconnection event may be localized to a specific region of the plasma outside the line of sight of the scintillator. The x-ray signal has also been seen accompanying the voltage spike when no Rayleigh-Taylor is observed. This may be due to the interframe timing on the camera being longer than the very short duration of the Rayleigh-Taylor instability.

  13. Particle Acceleration in Collapsing Magnetic Traps with a Braking Plasma Jet

    CERN Document Server

    Borissov, Alexei; Threlfall, James

    2016-01-01

    Collapsing magnetic traps (CMTs) are one proposed mechanism for generating non-thermal particle populations in solar flares. CMTs occur if an initially stretched magnetic field structure relaxes rapidly into a lower-energy configuration, which is believed to happen as a by-product of magnetic reconnection. A similar mechanism for energising particles has also been found to operate in the Earth's magnetotail. One particular feature proposed to be of importance for particle acceleration in the magnetotail is that of a braking plasma jet, i.e. a localised region of strong flow encountering stronger magnetic field which causes the jet to slow down and stop. Such a feature has not been included in previously proposed analytical models of CMTs for solar flares. In this work we incorporate a braking plasma jet into a well studied CMT model for the first time. We present results of test particle calculations in this new CMT model. We observe and characterise new types of particle behaviour caused by the magnetic stru...

  14. Long wavelength perfect fluidity from short distance jet transport in quark-gluon plasmas

    Science.gov (United States)

    Xu, Jiechen; Liao, Jinfeng; Gyulassy, Miklos

    2016-12-01

    We build a new phenomenological framework that bridges the long wavelength bulk viscous transport properties of the strongly-coupled quark-gluon plasma (sQGP) and short distance hard jet transport properties in the QGP. The full nonperturbative chromo-electric (E) and chromo-magnetic (M) structure of the near "perfect fluid" like sQGP in the critical transition region are integrated into a semi-Quark-Gluon-Monopole Plasma (sQGMP) model lattice-compatibly and implemented into the new CUJET3.0 jet quenching framework. All observables computed from CUJET3.0 are found to be consistent with available data at RHIC and LHC simultaneously. A quantitative connection between the shear viscosity and jet transport parameter is rigorously established within this framework. We deduce the T = 160 - 600 MeV dependence of the QGP's η / s: its near vanishing value in the near Tc regime is determined by the composition of E and M charges, it increases as T rises, and its high T limit is fixed by color screening scales.

  15. Synthetic

    Directory of Open Access Journals (Sweden)

    Anna Maria Manferdini

    2010-06-01

    Full Text Available Traditionally materials have been associated with a series of physical properties that can be used as inputs to production and manufacturing. Recently we witnessed an interest in materials considered not only as ‘true matter’, but also as new breeds where geometry, texture, tooling and finish are able to provoke new sensations when they are applied to a substance. These artificial materials can be described as synthetic because they are the outcome of various qualities that are not necessarily true to the original matter, but they are the combination of two or more parts, whether by design or by natural processes. The aim of this paper is to investigate the potential of architectural surfaces to produce effects through the invention of new breeds of artificial matter, using micro-scale details derived from Nature as an inspiration.

  16. Temperature diagnostics of a non-thermal plasma jet at atmospheric pressure

    Science.gov (United States)

    Schäfer, Jan

    2013-09-01

    The study reflects the concept of the temperature as a physical quantity resulting from the second thermodynamic law. The reliability of different approaches of the temperature diagnostics of open non-equilibrium systems is discussed using examples of low temperature atmospheric pressure discharges. The focus of this work is a miniaturized non-thermal atmospheric pressure plasma jet for local surface treatment at ambient atmosphere. The micro-discharge is driven with a capacitively coupled radio frequency electric field at 27.12 MHz and fed with argon at rates of about 1 slm through the capillary with an inner diameter of 4 mm. The discharge consists of several contracted filaments with diameter around 300 μm which are rotating azimuthally in the capillary in a self-organized manner. While the measured temperatures of the filament core exceed 700 K, the heat impact on a target below the plasma jet remains limited leading to target temperatures below 400 K. Different kinds of temperatures and energy transport processes are proposed and experimentally investigated. Nevertheless, a reliable and detailed temperature diagnostics is a challenge. We report on a novel diagnostics approach for the spatially and temporally resolved measurement of the gas temperature based on the optical properties of the plasma. Laser Schlieren Deflectometry is adapted to explore temperature profiles of filaments and their behaviour. In parallel, the method demonstrates a fundamental Fermat's principle of minimal energy. Information acquired with this method plays an important role for the optimization of local thin film deposition and surface functionalization by means of the atmospheric pressure plasma jet. The work was supported in part by the Deutsche Forschungsgemeinschaft within SFB-TR 24.

  17. Plasma transport properties at the L-H transition and high performance phase of JET discharges

    Energy Technology Data Exchange (ETDEWEB)

    Balet, B.; Cordey, J.G.; Erba, M.; Jones, T.T.C.; Lomas, P.J.; Smeulders, P.; Springmann, E.M.; Stubberfield, P.M.; Taroni, A.; Thomsen, K. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Parail, V.V. [Kurchatov Institute, Moscow (Russian Federation)

    1994-07-01

    Numerical analysis are performed which show that both electron and ion thermal diffusivities are reduced by one order of magnitude everywhere, not only in a narrow region near separatrix during the L-H transition. There is no separate H-VH transition on JET, this transition coincides with the cessation of ELMs. In the ELM free phase ion transport in the core is close to its neoclassical value, but probably rises towards plasma edge (however still remaining much less than it was in L-mode). The best agreement with experiment is obtained with the model which simultaneously takes into account both the global reduction of Bohm type anomalous transport in plasma core and formation of temperature pedestal near plasma edge. (authors). 6 refs., 5 figs.

  18. Optical Characteristics Investigation of the Cold Argon Plasma Jet for the Medical Applications

    Science.gov (United States)

    Nguyen-Kuok, Shi; Malakhov, Yury; Bach, Sy Minh; Korotkikh, Ivan

    2016-09-01

    The medical setup was designed for the treatment of wounds, disinfection of inflammation, for the destruction of damaged cells. The results of experimental determination of the optical characteristics of Argon cold plasma at atmospheric pressure are presented in the paper. The main components of the experimental setup are plasma torch, spectrometer, photo-electron multiplier, oscilloscope, gas consumption QAr = 1 - 20 l/min. Spectrum of the plasma jet is obtained using the grating spectrometer Spectra with radiometric calibration, operating in the visible range λ = 380 - 760 nm. The sun-blind photodetector was used for determination of the intensity of radiation in the UV range λ = 190 - 380 nm. The emission spectrum consists of a continuous radiation and the emissions of atoms and ions ArI and ArII. The analysis of spectral lines was carried out.

  19. Jet-dilepton conversion from an anisotropic quark-gluon plasma

    CERN Document Server

    Mukherjee, Arghya; Roy, Pradip

    2016-01-01

    We calculate the yield of lepton pair production from jet-plasma interaction where the plasma is anisotropic in momentum space. We compare both the $M$ and $p_T$ distributions from such process with the Drell-Yan contribution. It is observed that the invariant mass distribution of lepton pair from such process dominate over the Drell-Yan up to $3$ GeV at RHIC and up to $10$ GeV at LHC. Moreover, it is found that the contribution from anistropic quark gluon plasma (AQGP) increases marginally compared to the isotropic QGP. In case of $p_T$-distribution we observe an increase by a factor of $3-4$ in the entire $p_T$-range at RHIC for AQGP. However, at LHC the change in the $p_T$-distribution is marginal as compared to the isotropic case.

  20. Radiation-MHD Simulations of Plasma-Jet-Driven Magneto-Inertial Fusion Gain Using USim

    Science.gov (United States)

    Stoltz, Peter; Beckwith, Kristian; Kundrapu, Mahdusudhan; Hsu, Scott; Langendorf, Samuel

    2016-10-01

    One goal of the modeling effort for the PLX- α project is to identify plasma-jet-driven magneto-inertial fusion (PJMIF) configurations with potential net fusion-energy gain. We use USim, which is a tool for modeling high-energy-density plasmas using multi-fluid models coupled to electromagnetics using fully-implicit iterative solvers, combined with finite volume discretizations on unstructured meshes. We include physical viscosity and advanced-EOS modeling capability, and are investigating the effects of different radiation (including flux-limited diffusion) and alpha-transport models. We compare 2D and 1D gain calculations for various liner geometries, parameters, and plasma species, and consider the effects of liner non-uniformities on fusion-gain degradation. Supported by the ARPA-E ALPHA Program.

  1. Semi-analytic model of plasma-jet-driven magneto-inertial fusion

    Science.gov (United States)

    Langendorf, Samuel J.; Hsu, Scott C.

    2017-03-01

    A semi-analytic model for plasma-jet-driven magneto-inertial fusion is presented. Compressions of a magnetized plasma target by a spherically imploding plasma liner are calculated in one dimension (1D), accounting for compressible hydrodynamics and ionization of the liner material, energy losses due to conduction and radiation, fusion burn and alpha deposition, separate ion and electron temperatures in the target, magnetic pressure, and fuel burn-up. Results show 1D gains of 3-30 at spherical convergence ratio energy, for cases in which the liner thickness is 1 cm and the initial radius of a preheated magnetized target is 4 cm. Some exploration of parameter space and physics settings is presented. The yields observed suggest that there is a possibility of igniting additional dense fuel layers to reach high gain.

  2. Tungsten transport and sources control in JET ITER-like wall H-mode plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Fedorczak, N., E-mail: nicolas.fedorczak@cea.fr [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Monier-Garbet, P. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Pütterich, T. [MPI für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Brezinsek, S. [Institute of Energy and Climate Research, Forschungszentrum Jlich, Assoc EURATOM-FZJ, Jlich (Germany); Devynck, P.; Dumont, R.; Goniche, M.; Joffrin, E. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Lerche, E. [Association EURATOM-Belgian State, LPP-ERM-KMS, TEC partner, Brussels (Belgium); Euratom/CCFE Fusion Association, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); Lipschultz, B. [York Plasma Institute, University of York, Heslington, York YO10 5DD (United Kingdom); Luna, E. de la [Laboratorio Nacional de Fusin, Asociacin EURATOM/CIEMAT, 28040 Madrid (Spain); Maddison, G. [Culham Centre for Fusion Energy, EURATOM-CCFE Association, Abingdon (United Kingdom); Maggi, C. [MPI für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Matthews, G. [Culham Centre for Fusion Energy, EURATOM-CCFE Association, Abingdon (United Kingdom); Nunes, I. [Istituto de plasmas e fusao nuclear, Lisboa (Portugal); Rimini, F. [Culham Centre for Fusion Energy, EURATOM-CCFE Association, Abingdon (United Kingdom); Solano, E.R. [Laboratorio Nacional de Fusin, Asociacin EURATOM/CIEMAT, 28040 Madrid (Spain); Tamain, P. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Tsalas, M. [Association EURATOM-Hellenic Republic, NCSR Demokritos 153 10, Attica (Greece); Vries, P. de [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

    2015-08-15

    A set of discharges performed with the JET ITER-like wall is investigated with respect to control capabilities on tungsten sources and transport. In attached divertor regimes, increasing fueling by gas puff results in higher divertor recycling ion flux, lower divertor tungsten source, higher ELM frequency and lower core plasma radiation, dominated by tungsten ions. Both pedestal flushing by ELMs and divertor screening (including redeposition) are possibly responsible. For specific scenarios, kicks in plasma vertical position can be employed to increase the ELM frequency, which results in slightly lower core radiation. The application of ion cyclotron radio frequency heating at the very center of the plasma is efficient to increase the core electron temperature gradient and flatten electron density profile, resulting in a significantly lower central tungsten peaking. Beryllium evaporation in the main chamber did not reduce the local divertor tungsten source whereas core radiation was reduced by approximately 50%.

  3. Helium metastable dynamics in sheath or bulk dominated rf micro-plasma jets

    CERN Document Server

    Niermann, B; Wollny, A; Böke, M; Brinkmann, R P; Mussenbrock, T; Winter, J

    2011-01-01

    Space resolved concentrations of helium He metastable atoms in an atmospheric pressure radio-frequency micro-plasma jet were measured using tunable diode laser absorption spectroscopy. The spatial profile of metastable atoms in the volume between the electrodes was deduced for various electrode gap distances. Density profiles reveal the sheath structure and reflect the plasma excitation distribution, as well as the dominance of the alpha-mode discharge. Gap width variations show the transition from a normal glow plasma to a pure sheath discharge. In order to analyze and verify the experimentally observed profiles of the metastable atoms a 2-dimensional simulation model was set up. Applying an appropriate He/N2/O2 chemistry model the correlation between the metastable profiles and the underlying excitation mechanisms was obtained.

  4. On drag forces and jet quenching in strongly-coupled plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Caceres, Elena [Facultad de Ciencias, Universidad de Colima, Bernal Diaz del Castillo 340, Colima, Colima (Mexico); Gueijosa, Alberto [Departamento de Fisica de Altas Energias, Instituto de Ciencias Nucleares, Universidad Autonoma de Mexico, Apdo. Postal 70-543, Mexico D.F.04510 (Mexico)

    2006-12-15

    We compute the drag force experienced by a heavy quark that moves through plasma in a gauge theory whose dual description involves arbitrary metric and dilaton fields. As a concrete application, we consider the cascading gauge theory at temperatures high above the deconfining scale, where we obtain a drag force with a non-trivial velocity dependence. We compare our results with the jet-quenching parameter for the same theory, and find qualitative agreement between the two approaches. Conversely, we calculate the jet-quenching parameter for N = 4 super-Yang-Mills with an R-charge density (or equivalently, a chemical potential), and compare our result with the corresponding drag force.

  5. 3D printing of gas jet nozzles for laser-plasma accelerators

    Science.gov (United States)

    Döpp, A.; Guillaume, E.; Thaury, C.; Gautier, J.; Ta Phuoc, K.; Malka, V.

    2016-07-01

    Recent results on laser wakefield acceleration in tailored plasma channels have underlined the importance of controlling the density profile of the gas target. In particular, it was reported that the appropriate density tailoring can result in improved injection, acceleration, and collimation of laser-accelerated electron beams. To achieve such profiles, innovative target designs are required. For this purpose, we have reviewed the usage of additive layer manufacturing, commonly known as 3D printing, in order to produce gas jet nozzles. Notably we have compared the performance of two industry standard techniques, namely, selective laser sintering (SLS) and stereolithography (SLA). Furthermore we have used the common fused deposition modeling to reproduce basic gas jet designs and used SLA and SLS for more sophisticated nozzle designs. The nozzles are characterized interferometrically and used for electron acceleration experiments with the Salle Jaune terawatt laser at Laboratoire d'Optique Appliquée.

  6. 3D printing of gas jet nozzles for laser-plasma accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Döpp, A.; Guillaume, E.; Thaury, C.; Gautier, J.; Ta Phuoc, K.; Malka, V. [LOA, ENSTA ParisTech, CNRS, École Polytechnique, Université Paris-Saclay, 828 Boulevard des Maréchaux, 91762 Palaiseau Cedex (France)

    2016-07-15

    Recent results on laser wakefield acceleration in tailored plasma channels have underlined the importance of controlling the density profile of the gas target. In particular, it was reported that the appropriate density tailoring can result in improved injection, acceleration, and collimation of laser-accelerated electron beams. To achieve such profiles, innovative target designs are required. For this purpose, we have reviewed the usage of additive layer manufacturing, commonly known as 3D printing, in order to produce gas jet nozzles. Notably we have compared the performance of two industry standard techniques, namely, selective laser sintering (SLS) and stereolithography (SLA). Furthermore we have used the common fused deposition modeling to reproduce basic gas jet designs and used SLA and SLS for more sophisticated nozzle designs. The nozzles are characterized interferometrically and used for electron acceleration experiments with the SALLE JAUNE terawatt laser at Laboratoire d’Optique Appliquée.

  7. 3D printing of gas jet nozzles for laser-plasma accelerators

    CERN Document Server

    Döpp, A; Thaury, C; Gautier, J; Phuoc, K Ta; Malka, V

    2016-01-01

    Recent results on laser wakefield acceleration in tailored plasma channels have underlined the importance of controlling the density profile of the gas target. In particular it was reported that appropriate density tailoring can result in improved injection, acceleration and collimation of laser-accelerated electron beams. To achieve such profiles innovative target designs are required. For this purpose we have reviewed the usage of additive layer manufacturing, commonly known as 3D printing, in order to produce gas jet nozzles. Notably we have compared the performance of two industry standard techniques, namely selective laser sintering (SLS) and stereolithography (SLA). Furthermore we have used the common fused deposition modeling (FDM) to reproduce basic gas jet designs and used SLA and SLS for more sophisticated nozzle designs. The nozzles are characterized interferometrically and used for electron acceleration experiments with the Salle Jaune terawatt laser at Laboratoire d'Optique Appliqu\\'ee.

  8. Detection of HO2 in an atmospheric pressure plasma jet using optical feedback cavity-enhanced absorption spectroscopy

    Science.gov (United States)

    Gianella, Michele; Reuter, Stephan; Lawry Aguila, Ana; Ritchie, Grant A. D.; van Helden, Jean-Pierre H.

    2016-11-01

    Cold non-equilibrium atmospheric pressure plasma jets are increasingly applied in material processing and plasma medicine. However, their small dimensions make diagnosing the fluxes of generated species a challenge. Here we report on the detection of the hydroperoxyl radical, HO2, in the effluent of a plasma jet by the use of optical feedback cavity-enhanced absorption spectroscopy. The spectrometer has a minimum detectable absorption coefficient {α }\\min of 2.25× {10}-10 cm-1 with a 100 second acquisition, equivalent to 5.5× {10}12 {{cm}}-3 of HO2 (under ideal conditions). Concentrations in the range of (3.1-7.8) × 1013 cm-3 were inferred in the 4 mm wide effluent of the plasma jet.

  9. The effects of added hydrogen on a helium atmospheric-pressure plasma jet ambient desorption/ionization source.

    Science.gov (United States)

    Wright, Jonathan P; Heywood, Matthew S; Thurston, Glen K; Farnsworth, Paul B

    2013-03-01

    We present mass spectrometric data demonstrating the effect that hydrogen has on a helium-based dielectric-barrier discharge (DBD) atmospheric-pressure plasma jet used as an ambient desorption/ionization (ADI) source. The addition of 0.9 % hydrogen to the helium support gas in a 35-W plasma jet increased signals for a range of test analytes, with enhancement factors of up to 68, without proportional increases in background levels. The changes in signal levels result from a combination of changes in the desorption kinetics from the surface and increased ion production in the gas phase. The enhancement in ADI-MS performance despite the quenching of key plasma species reported in earlier studies suggests that ionization with a H2/He plasma jet is the result of an alternate mechanism involving the direct generation of ionized hydrogen.

  10. Investigating the Mutagenicity of a Cold Argon-Plasma Jet in an HET-MN Model

    Science.gov (United States)

    Bender, Claudia; Benkhai, Hicham; Sckell, Axel; Below, Harald; Stope, Matthias B.; Kramer, Axel

    2016-01-01

    Objective So-called cold physical plasmas for biomedical applications generate reactive oxygen and nitrogen species and the latter can trigger DNA damage at high concentrations. Therefore, the mutagenic risks of a certified atmospheric pressure argon plasma jet (kINPen MED) and its predecessor model (kINPen 09) were assessed. Methods Inner egg membranes of fertilized chicken eggs received a single treatment with either the kINPen 09 (1.5, 2.0, or 2.5 min) or the kINPen MED (3, 4, 5, or 10 min). After three days of incubation, blood smears (panoptic May-Grünwald-Giemsa stain) were performed, and 1000 erythrocytes per egg were evaluated for the presence of polychromatic and normochromic nuclear staining as well as nuclear aberrations and binucleated cells (hen’s egg test for micronuclei induction, HET-MN). At the same time, the embryo mortality was documented. For each experiment, positive controls (cyclophosphamide and methotrexate) and negative controls (NaCl-solution, argon gas) were included. Additionally, the antioxidant potential of the blood plasma was assessed by ascorbic acid oxidation assay after treatment. Results For both plasma sources, there was no evidence of genotoxicity, although at the longest plasma exposure time of 10 min the mortality of the embryos exceeded 40%. The antioxidant potential in the egg’s blood plasma was not significantly reduced immediately (p = 0.32) or 1 h (p = 0.19) post exposure to cold plasma. Conclusion The longest plasma treatment time with the kINPen MED was 5–10 fold above the recommended limit for treatment of chronic wounds in clinics. We did not find mutagenic effects for any plasma treatment time using the either kINPen 09 or kINPen MED. The data provided with the current study seem to confirm the lack of a genotoxic potential suggesting that a veterinary or clinical application of these argon plasma jets does not pose mutagenic risks. PMID:27584003

  11. A Sub-microsecond Pulsed Plasma Jet for Endodontic Biofilm Disinfection

    Science.gov (United States)

    Jiang, Chunqi; Schaudinn, Christoph; Jaramillo, David E.; Gundersen, Martin A.; Costerton, J. William

    A pulsed, tapered cylindrical plasma jet, several centimeter long and Enterococcus faecalis biofilms on bovine dentins. Resultant colony-forming unit counts were associated with changes in bacterial cell morphology observed using scanning electron microscopy (SEM) following the treatment and control. Treatment of dentin discs cultivated with E. faecalis monolayer biofilms with the plasma (average power ≈ 1 W) for 5 min resulted in 92.4% kill (P < 0.0001). Severe disruption of the cell membranes was observed for the plasma treatment group, while the morphology of the cells remained intact for the negative control group. In addition, a pilot ex vivo test was conducted to examine the bactericidal effect of the plasma against saliva-derived biofilms cultivated in human root canals. Conspicuous biofilm disruption and cleared dentinal surfaces were observed in the canal after the plasma treatment for 5 min. We ­conclude that this non-thermal pulsed plasma-based technology is a potential ­alternative or supplement to existing protocols for root canal disinfection.

  12. Direct protein introduction into plant cells using a multi-gas plasma jet.

    Science.gov (United States)

    Yanagawa, Yuki; Kawano, Hiroaki; Kobayashi, Tomohiro; Miyahara, Hidekazu; Okino, Akitoshi; Mitsuhara, Ichiro

    2017-01-01

    Protein introduction into cells is more difficult in plants than in mammalian cells, although it was reported that protein introduction was successful in shoot apical meristem and leaves only together with a cell-penetrating peptide. In this study, we tried to introduce superfolder green fluorescent protein (sGFP)-fused to adenylate cyclase as a reporter protein without a cell-penetrating peptide into the cells of tobacco leaves by treatment with atmospheric non-thermal plasmas. For this purpose, CO2 or N2 plasma was generated using a multi-gas plasma jet. Confocal microscopy indicated that sGFP signals were observed inside of leaf cells after treatment with CO2 or N2 plasma without substantial damage. In addition, the amount of cyclic adenosine monophosphate (cAMP) formed by the catalytic enzyme adenylate cyclase, which requires cellular calmodulin for its activity, was significantly increased in leaves treated with CO2 or N2 plasma, also indicating the introduction of sGFP-fused adenylate cyclase into the cells. These results suggested that treatment with CO2 or N2 plasma could be a useful technique for protein introduction into plant tissues.

  13. [Investigation on the gas temperature of a plasma jet at atmospheric pressure by emission spectrum].

    Science.gov (United States)

    Li, Xue-chen; Yuan, Ning; Jia, Peng-ying; Niu, Dong-ying

    2010-11-01

    A plasma jet of a dielectric barrier discharge in coaxial electrode was used to produce plasma plume in atmospheric pressure argon. Spatially and temporally resolved measurement was carried out by photomultiplier tubes. The light emission signals both from the dielectric barrier discharge and from the plasma plume were analyzed. Furthermore, emission spectrum from the plasma plume was collected by high-resolution optical spectrometer. The emission spectra of OH (A 2sigma + --> X2 II, 307.7-308.9 nm) and the first negative band of N2+ (B2 sigma u+ --> X2 IIg+, 390-391.6 nm) were used to estimate the rotational temperature of the plasma plume by fitting the experimental spectra to the simulated spectra. The rotational temperature obtained is about 443 K by fitting the emission spectrum from the OH, and that from the first negative band of N2+ is about 450 K. The rotational temperatures obtained by the two method are consistent within 5% error band. The gas temperature of the plasma plume at atmospheric pressure was obtained because rotational temperature equals to gas temperature approximately in gas discharge at atmospheric pressure. Results show that gas temperature increases with increasing the applied voltage.

  14. Development of a radio frequency atmospheric pressure plasma jet for diamond-like carbon coatings on stainless steel substrates

    Science.gov (United States)

    Sohbatzadeh, F.; Samadi, O.; Siadati, S. N.; Etaati, G. R.; Asadi, E.; Safari, R.

    2016-10-01

    In this paper, an atmospheric pressure plasma jet with capacitively coupled radio frequency discharge was developed for diamond-like carbon (DLC) coatings on stainless steel substrates. The plasma jet was generated by argon-methane mixture and its physical parameters were investigated. Relation between the plasma jet length and width of the powered electrode was discussed. Optical and electrical characteristics were studied by optical emission spectroscopy, voltage and current probes, respectively. The evolutions of various species like ArI, C2 and CH along the jet axis were investigated. Electron temperature and density were estimated by Boltzmann plot method and Saha-Boltzmann equation, respectively. Finally, a diamond-like carbon coating was deposited on stainless steel-304 substrates by the atmospheric pressure radio frequency plasma jet in ambient air. Raman spectroscopy, scanning electron microscopy (SEM), atomic force microscopy and Vickers hardness test were used to study the deposited films. The length of the jet was increased by increasing the width of the powered electrode. The estimated electron temperature and density were 1.43 eV and 1.39 × 1015 cm-3, respectively. Averaged Vicker's hardness of the coated sample was three times greater than that of the substrate. The SEM images of the deposited thin films revealed a 4.5 μm DLC coated for 20 min.

  15. Effects of a Nonthermal Atmospheric Pressure Plasma Jet on Human Gingival Fibroblasts for Biomedical Application

    Directory of Open Access Journals (Sweden)

    Jung-Hwan Lee

    2016-01-01

    Full Text Available Nonthermal atmospheric pressure plasma jets (APPJ have been developed and applied in biomedical research as a cancer treatment or bacterial sterilization. However, the drawback of APPJ on normal oral cells during plasma treatment and underlying cell death mechanisms have not been studied and clearly explained, although there is known to be an influence from reactive oxygen species (ROS. Hence, this study investigates whether and how a nonthermal atmospheric pressure air plasma jet kills human normal gingival cells using immortalized human gingival fibroblasts (hTERT-hNOF cells. In this study, a set of physicochemical or biological methods were used to illuminate the killing mechanisms. It was found that ROS were induced intracellularly without a breakdown of the cell wall and apoptosis was involved in cell death when an air APPJ treatment was performed on the cells directly without media; the air treatment only supported a detachment of the cells without increase of ROS. It was also revealed that a correlation between intracellular ROS concentration and cells viability existed. These results indicated that the direct air APPJ treatment possibly raises safety issue to normal tissue and thereby APPJ application in biomedical field needs more in vitro and in vivo study to optimize it.

  16. Influence of discharge and jet flow coupling on atmospheric pressure plasma homogeneity

    Science.gov (United States)

    Nizard, H.; Gaudy, T.; Toutant, A.; Iacono, J.; Descamps, P.; Leempoel, P.; Massines, F.

    2015-10-01

    The effect of flow dynamics on the discharge mode is studied in order to design a technical solution for thin film coating on large surfaces. The configuration consists in two atmospheric pressure helium plasma jets impacting a surface and confined in a tube. This system operates in open air. It has been studied by short exposure time pictures, current and voltage measurements, optical emission spectroscopy, schlieren flow visualization and computational fluid dynamics. Two discharge regimes directly connected to the gas flow dynamic have been pointed out. One is localized from the point electrodes to the surface; the other one entirely fills the confinement tube. A correlation between air intake inside the confinement tube and the discharge mode has been highlighted. Indeed, the discharge only develops in helium and the air intake confines the helium jets in volumes smaller than the confinement tube. The air intake is determined by the gas flow rate and the distance from the tube bottom to the substrate surface, parameters which have been linked to the change from laminar to turbulent flow. Finally, the understanding of flow dynamics and discharge plasma coupling allowed the design of a technical solution favoring plasma homogeneity for large surface treatment.

  17. Atmospheric pressure plasma jet-synthesized electrochromic organomolybdenum oxide thin films for flexible electrochromic devices

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Yung-Sen, E-mail: yslin@fcu.edu.tw; Tsai, Tsung-Hsien; Tien, Shih-Wei

    2013-02-01

    An investigation is conducted into fast synthesis of electrochromic organomolybdenum oxide (MoO{sub x}C{sub y}) thin films onto 40 Ω/□ flexible polyethylene terephthalate/indium tin oxide substrates via atmospheric pressure plasma jet. A precursor [molybdenum carbonyl, Mo(CO){sub 6}] vapor, carried by argon gas, is injected into air plasma torch to synthesize MoO{sub x}C{sub y} films for offering extraordinary electrochromic performance. Only low driving voltages from − 1 V to 1 V are needed to offer reversible Li{sup +} ion intercalation and deintercalation in a 1 M LiClO{sub 4}-propylene carbonate electrolyte. Light modulation with transmittance variation of up to 61%, optical density change of 0.54 and coloration efficiency of 37.5 cm{sup 2}/C at a wavelength of 550 nm after 200 cycles of cyclic voltammetry switching measurements is achieved. - Highlights: ► Fast deposition of MoO{sub x}C{sub y} film by an atmospheric pressure plasma jet ► Organic–inorganic hybrid MoO{sub x}C{sub y} films synthesized ► Flexible and electrochromic MoO{sub x}C{sub y} films produced.

  18. Effect of sheath gas in atmospheric-pressure plasma jet for potato sprouting suppression

    Science.gov (United States)

    Nishiyama, S.; Monma, M.; Sasaki, K.

    2016-09-01

    Recently, low-temperature atmospheric-pressure plasma jets (APPJs) attract much interest for medical and agricultural applications. We try to apply APPJs for the suppression of potato sprouting in the long-term storage. In this study, we investigated the effect of sheath gas in APPJ on the suppression efficiency of the potato sprouting. Our APPJ was composed of an insulated thin wire electrode, a glass tube, a grounded electrode which was wound on the glass tube, and a sheath gas nozzle which was attached at the end of the glass tube. The wire electrode was connected to a rectangular-waveform power supply at a frequency of 3 kHz and a voltage of +/- 7 kV. Helium was fed through the glass tube, while we tested dry nitrogen, humid nitrogen, and oxygen as the sheath gas. Eyes of potatoes were irradiated by APPJ for 60 seconds. The sprouting probability was evaluated at two weeks after the plasma irradiation. The sprouting probability was 28% when we employed no sheath gases, whereas an improved probability of 10% was obtained when we applied dry nitrogen as the sheath gas. Optical emission spectroscopy was carried out to diagnose the plasma jet. It was suggested that reactive species originated from nitrogen worked for the efficient suppression of the potato sprouting.

  19. Degradation of carbon-based materials under ablative conditions produced by a high enthalpy plasma jet

    Directory of Open Access Journals (Sweden)

    Gilberto Petraconi

    2010-04-01

    Full Text Available A stationary experiment was performed to study the degradation of carbon-based materials by immersion in a plasma jet. In the experiment, graphite and C/C composite were chosen as the target materials, and the reactive plasma jet was generated by an air plasma torch. For macroscopic study of the material degradation, the sample’s mass losses were measured as function of the exposure time under various temperatures on the sample surface. A microscopic analysis was then carried out for the study of microscopic aspects of the erosion of material surface. These experiments showed that the mass loss per unit area is approximately proportional to the exposure time and strongly depends on the temperature of the material surface. The mass erosion rate of graphite was appreciably higher than the C/C composite. The ablation rate in the carbon matrix region in C/C composite was also noticeably higher than that in the fiber region. In addition, the latter varied according to the orientation of fibers relatively to the flow direction. These tests indicated an excellent ablation resistance of the C/C composite, thus being a reliable material for rocket nozzles and heat shielding elements of the protection systems of hypersonic apparatuses from aerodynamic heating.

  20. Plasma isotopic change over experiments in JET under Carbon and ITER-Like Wall conditions

    Energy Technology Data Exchange (ETDEWEB)

    Loarer, T., E-mail: thierry.loarer@cea.fr [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Brezinsek, S.; Philipps, V. [Forschungszentrum Jülich, Institut für Energie und Klimaforschung Plasmaphysik, 52425 Jülich (Germany); Romanelli-Gruenhagen, S. [Culham Centre for Fusion Energy, Abingdon, Oxon OX14 3DB (United Kingdom); Alves, D.; Carvalho, I. [IST, Instituto de Plasmas e Fusão Nuclear, IST Lisboa (Portugal); Douai, D. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Esser, H.G. [Forschungszentrum Jülich, Institut für Energie und Klimaforschung Plasmaphysik, 52425 Jülich (Germany); Felton, R. [Culham Centre for Fusion Energy, Abingdon, Oxon OX14 3DB (United Kingdom); Frigione, D. [ENEA sulla Fusione, Via E. Fermi 45, I-00044 Frascati (Italy); Kruezi, U. [Culham Centre for Fusion Energy, Abingdon, Oxon OX14 3DB (United Kingdom); Reux, C. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Smith, R.; Stamp, M.F. [Culham Centre for Fusion Energy, Abingdon, Oxon OX14 3DB (United Kingdom); Vartanian, S. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France)

    2015-08-15

    Starting with a wall loaded by H{sub 2}, change over experiments from H{sub 2} to D{sub 2} have been carried out in JET-ILW. A series of 13 repetitive pulses (cumulating 215 s in divertor configuration) have been performed under conditions of: I{sub p} = 2.0 MA, B{sub T} = 2.4 T, 〈n{sub e}〉 = 4.5 × 10{sup 19} m{sup −3} with a constant gas injection of 3.0 × 10{sup 21} D s{sup −1} and 0.5 MW of auxiliary heating by ICRH in L-mode. Gas balance analysis shows that the total amount of H removed from the wall is in the range of 3 × 10{sup 22} D compared to 2 × 10{sup 23} D for JET-C. This is consistent with the faster decay of the H plasma concentration and the drop of the retention also by a similar factor when removing all the carbon components. Isotopic plasma wall changeover is also demonstrated to allow for removal of some D/T from the device. However, since plasma change over also contributes to long-term retention by codeposition, in ITER, change over in between each discharge might not be effective to reduce the fuel retention on the long-term.

  1. Holographic Three-Jet Events in Strongly Coupled N=4 Yang-Mills Plasma

    CERN Document Server

    Casalderrey-Solana, Jorge

    2015-01-01

    We analyse classical string configurations with non-trivial transverse dynamics in $AdS_5$-Schwarzschild. These strings develop kink-like structures which, via the gauge/gravity duality, can be interpreted as the propagation of hard gluons produced in association with a quark-antiquark pair in a strongly coupled $\\mathcal{N}=4$ SYM plasma. We observe the appearance of two physically distinct regimes of the in-plasma dynamics, depending on whether the medium is able to resolve the transverse structure of the string prior to its total quench. From these studies we extract the medium resolution scale of the strongly coupled SYM plasma, defined as the smallest angular separation between two jets that the medium can resolve, $\\theta_{\\rm res} = \\mathcal{C}_{\\rm res} ( E /\\sqrt{\\lambda} T)^{-2/3}$, where $\\mathcal{C}_{\\rm res}= \\frac{2^{4/3}}{\\pi}\\frac{\\Gamma(3/4)^2}{\\Gamma(5/4)^2}$. Our analysis constitutes the first study of proxies for three-jet events in a holographic context.

  2. Effects of a Nonthermal Atmospheric Pressure Plasma Jet on Human Gingival Fibroblasts for Biomedical Application.

    Science.gov (United States)

    Lee, Jung-Hwan; Kim, Kyoung-Nam

    2016-01-01

    Nonthermal atmospheric pressure plasma jets (APPJ) have been developed and applied in biomedical research as a cancer treatment or bacterial sterilization. However, the drawback of APPJ on normal oral cells during plasma treatment and underlying cell death mechanisms have not been studied and clearly explained, although there is known to be an influence from reactive oxygen species (ROS). Hence, this study investigates whether and how a nonthermal atmospheric pressure air plasma jet kills human normal gingival cells using immortalized human gingival fibroblasts (hTERT-hNOF cells). In this study, a set of physicochemical or biological methods were used to illuminate the killing mechanisms. It was found that ROS were induced intracellularly without a breakdown of the cell wall and apoptosis was involved in cell death when an air APPJ treatment was performed on the cells directly without media; the air treatment only supported a detachment of the cells without increase of ROS. It was also revealed that a correlation between intracellular ROS concentration and cells viability existed. These results indicated that the direct air APPJ treatment possibly raises safety issue to normal tissue and thereby APPJ application in biomedical field needs more in vitro and in vivo study to optimize it.

  3. Modification of ink-jet paper by oxygen-plasma treatment

    Energy Technology Data Exchange (ETDEWEB)

    Vesel, A [Jozef Stefan Institute, Jamova 39, Ljubljana 1000 (Slovenia); Mozetic, M [Jozef Stefan Institute, Jamova 39, Ljubljana 1000 (Slovenia); Hladnik, A [Pulp and Paper Institute, Bogisiceva 8, Ljubljana 1001 (Slovenia); Dolenc, J [Pulp and Paper Institute, Bogisiceva 8, Ljubljana 1001 (Slovenia); Zule, J [Pulp and Paper Institute, Bogisiceva 8, Ljubljana 1001 (Slovenia); Milosevic, S [Institute of Physics, Bijenicka 46, Zagreb 10000 (Croatia); Krstulovic, N [Institute of Physics, Bijenicka 46, Zagreb 10000 (Croatia); Klanjsek-Gunde, M [National Institute of Chemistry, Hajdrihova 19, Ljubljana 1000 (Slovenia); Hauptmann, N [National Institute of Chemistry, Hajdrihova 19, Ljubljana 1000 (Slovenia)

    2007-06-21

    A study on oxygen-plasma treatment of ink-jet paper is presented. Paper was exposed to a weakly ionized, highly dissociated oxygen plasma with an electron temperature of 5 eV, a positive-ion density of 8 x 10{sup 15} m{sup -3} and a density of neutral oxygen atoms of 5 x 10{sup 21} m{sup -3}. Optical emission spectroscopy (OES) was applied as a method for detection of the reaction products during the plasma treatment of the paper. OES spectra between 250 and 1000 nm were measured continuously during the plasma treatment. The wettability of the samples before and after the plasma treatment was determined by measuring the contact angle of a water drop. The appearance of the surface-functional groups was determined by using high-resolution x-ray photoelectron spectroscopy (XPS), while changes in the surface morphology were monitored with scanning electron microscopy (SEM). Already after 1 s of the plasma treatment the surface, which was originally hydrophobic, changed to hydrophilic, as indicated by a high absorption rate of a water drop into the paper. The OES showed a rapid increase of the CO and OH bands for the first few seconds of the plasma treatment, followed by a slow decrease during the next 40 s. The intensity of the O atom line showed reversed behaviour. The XPS analyses showed a gradual increase of oxygen-rich functional groups on the surface, while SEM analyses did not show significant modification of the morphology during the first 10 s of the plasma treatment. The results were explained by degradation of the alkyl ketene dimer sizing agent during the first few seconds of the oxygen-plasma treatment.

  4. Spatial and Excitation Variations for Different Applied Voltages in an Atmospheric Neon Plasma Jet

    Science.gov (United States)

    Yang, Lanlan; Tu, Yan; Yu, Yongbo; Hu, Dinglan; Zhang, Xiong

    2016-09-01

    A neon plasma jet was generated in air, driven by a 9 kHz sinusoidal power supply. The characteristics of the plasma plume and the optical spectra with plasma propagation for different applied voltages were investigated. By increasing the applied voltage, the plasma plume first increases and then retracts to become short and bulky. The shortened effect of Ne plasma plume (about 10 mm) for the further voltage increasing is more apparent than that of He (about 3 mm) and Ar (about 1 mm). Emission intensity of the N2 (337 nm) increases with the applied voltage, gradually substituting the emission intensity of Ne (702 nm and 585 nm) as the noticeable radiation. At the nozzle opening, the Ne (702 nm) emission dominates, while the Ne (585 nm) emission is most noticeable around the tip of the plasma plume. The spatial distribution of the three spectral lines indicates that Ne (702 nm) emission decreases dramatically with plasma propagation while Ne (585 nm) and N2 (337 nm) emissions reach their maxima at the middle of the plasma plume. The results indicate that the Ne (702 nm) emission is much more sensitive to the average electron temperature and the density of the high-energy electrons, so it changes greatly at the tube nozzle and little at the tip region as the voltage increases. The population of high-energy electrons, the average electron temperature, the collision with air molecules and the Penning effect between Ne metastables and air molecules may explain their different variations with plasma propagating and voltage increasing. supported by National Natural Science Fundation of China (No. 61271053), the Natural Science Foundation of Jiangsu Province of China (No. BK2012737), the Foundation for Excellent Youth Scholars of Southeast University, China

  5. Comparison of two electro-hydrodynamic force models for the interaction between helium jet flow and an atmospheric-pressure "plasma jet"

    Science.gov (United States)

    Logothetis, D.; Papadopoulos, P. K.; Svarnas, P.; Vafeas, P.

    2016-12-01

    In this work, two simple phenomenological models of the electro-hydrodynamic force that arises in an atmospheric-pressure "plasma jet" are presented. The models are distinguished by the different boundary conditions applied for the consideration of the plasma propagation length. The comparison is based on numerical simulations, which are combined with experimental data, in order to determine the magnitude of the electro-hydrodynamic force and assess the ability of the two models to evaluate the visible plasma length. The results reveal that the gas flow characteristics depend on the spatial range of the force action and the force magnitude, and vice versa.

  6. Synthetic plasma edge diagnostics for EMC3-EIRENE, highlighted for Wendelstein 7-X

    Science.gov (United States)

    Frerichs, H.; Effenberg, F.; Schmitz, O.; Biedermann, C.; Feng, Y.; Jakubowski, M.; König, R.; Krychowiak, M.; Lore, J.; Niemann, H.; Pedersen, T. S.; Stephey, L.; Wurden, G. A.

    2016-11-01

    Interpretation of spectroscopic measurements in the edge region of high-temperature plasmas can be a challenge since line of sight integration effects make direct interpretation in terms of quantitative, local emission strengths often impossible. The EMC3-EIRENE code—a 3D fluid edge plasma and kinetic neutral gas transport code—is a suitable tool for full 3D reconstruction of such signals. A versatile synthetic diagnostic module has been developed recently which allows the realistic 3D setup of various plasma edge diagnostics to be captured. We highlight these capabilities with two examples for Wendelstein 7-X (W7-X): a visible camera for the analysis of recycling, and a coherent-imaging system for velocity measurements.

  7. Simulation of a Synthetic Jet in Quiescent Air Using TLNS3D Flow Code

    Science.gov (United States)

    Vatsa, Veer N.; Turkel, Eli

    2007-01-01

    Although the actuator geometry is highly three-dimensional, the outer flowfield is nominally two-dimensional because of the high aspect ratio of the rectangular slot. For the present study, this configuration is modeled as a two-dimensional problem. A multi-block structured grid available at the CFDVAL2004 website is used as a baseline grid. The periodic motion of the diaphragm is simulated by specifying a sinusoidal velocity at the diaphragm surface with a frequency of 450 Hz, corresponding to the experimental setup. The amplitude is chosen so that the maximum Mach number at the jet exit is approximately 0.1, to replicate the experimental conditions. At the solid walls zero slip, zero injection, adiabatic temperature and zero pressure gradient conditions are imposed. In the external region, symmetry conditions are imposed on the side (vertical) boundaries and far-field conditions are imposed on the top boundary. A nominal free-stream Mach number of 0.001 is imposed in the free stream to simulate incompressible flow conditions in the TLNS3D code, which solves compressible flow equations. The code was run in unsteady (URANS) mode until the periodicity was established. The time-mean quantities were obtained by running the code for at least another 15 periods and averaging the flow quantities over these periods. The phase-locked average of flow quantities were assumed to be coincident with their values during the last full time period.

  8. Characterization of Synthetic GTL Jet Fuel for use in Gas Turbine Engines

    Science.gov (United States)

    Sadr, Reza; Kannaiyan, Kumaran

    2010-11-01

    Stringent emission regulations have instigated the search for alternative-clean source of energy. Recently, Gas-to-Liquid (GTL) fuel has grabbed the global attention by its clean combustion characteristics owing to the absence of aromatics and Sulphur. However, this will introduce potential risks and benefits. Last fall Qatar airways has proven the feasibility of using GTL as a potential alternative clean fuel by a 3200 mile flight using a fuel blend of 50% JetA + 50% GTL. Researchers from Texas A & M University at Qatar (TAMUQ) in collaboration with their counterparts in Rolls-Royce (RR), UK, and German Aerospace Laboratory (DLR) are in a joint effort to establish an in-depth characterization of the combustion performance of GTL fuel in gas turbine engines. In TAMUQ, the research focus is to investigate the spray characteristics of GTL fuels. The results will be compared with that of standard fuel and correlate with combustion results to gain insights on GTL performance. This will help designers to optimize the nozzle geometry to improve the combustor performance. The objective of this talk is to introduce this ongoing effort and to discuss the experimental facility and preliminary results.

  9. Nonequilibrium atmospheric pressure plasma jet using a combination of 50 kHz/2 MHz dual-frequency power sources

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Yong-Jie; Yuan, Qiang-Hua; Li, Fei; Wang, Xiao-Min; Yin, Gui-Qin; Dong, Chen-Zhong [Key Laboratory of Atomic and Molecular Physics and Functional Materials of Gansu Province, College of Physics and Electronic Engineering, Northwest Normal University, Lanzhou 730070 (China)

    2013-11-15

    An atmospheric pressure plasma jet is generated by dual sinusoidal wave (50 kHz and 2 MHz). The dual-frequency plasma jet exhibits the advantages of both low frequency and radio frequency plasmas, namely, the long plasma plume and the high electron density. The radio frequency ignition voltage can be reduced significantly by using dual-frequency excitation compared to the conventional radio frequency without the aid of the low frequency excitation source. A larger operating range of α mode discharge can be obtained using dual-frequency excitation which is important to obtain homogeneous and low-temperature plasma. A larger controllable range of the gas temperature of atmospheric pressure plasma could also be obtained using dual-frequency excitation.

  10. Atmospheric-pressure plasma jet induces DNA double-strand breaks that require a Rad51-mediated homologous recombination for repair in Saccharomyces cerevisiae.

    Science.gov (United States)

    Lee, Yoonna; Kim, Kangil; Kang, Kyu-Tae; Lee, Jong-Soo; Yang, Sang Sik; Chung, Woo-Hyun

    2014-10-15

    Non-thermal plasma generated under atmospheric pressure produces a mixture of chemically reactive molecules and has been developed for a number of biomedical applications. Recently, plasma jet has been proposed as novel cancer therapies based on the observation that free radicals generated by plasma jet induce mitochondria-mediated apoptotic cell death. We show here that air plasma jet induces DNA double-strand breaks (DSBs) in yeast chromosomes leading to genomic instability and loss of viability, which are alleviated by Rad51, the yeast homolog of Escherichiacoli RecA recombinase, through DNA damage repair by a homologous recombination (HR) process. Hypersensitivity of rad51 mutant to air plasma was not restored by antioxidant treatment unlike sod1 mutant that was highly sensitive to reactive oxygen species (ROS) challenge, suggesting that plasma jet induces DSB-mediated cell death independent of ROS generation. These results may provide a new insight into the mechanism of air plasma jet-induced cell death.

  11. Synthetic Aperture Microwave Imaging (SAMI) of the plasma edge on NSTX-U

    Science.gov (United States)

    Vann, Roddy; Taylor, Gary; Brunner, Jakob; Ellis, Bob; Thomas, David

    2016-10-01

    The Synthetic Aperture Microwave Imaging (SAMI) system is a unique phased-array microwave camera with a +/-40° field of view in both directions. It can image cut-off surfaces corresponding to frequencies in the range 10-34.5GHz; these surfaces are typically in the plasma edge. SAMI operates in two modes: either imaging thermal emission from the plasma (often modified by its interaction with the plasma edge e.g. via BXO mode conversion) or ``active probing'' i.e. injecting a broad beam at the plasma surface and imaging the reflected/back-scattered signal. SAMI was successfully pioneered on the Mega-Amp Spherical Tokamak (MAST) at Culham Centre for Fusion Energy. SAMI has now been installed and commissioned on the National Spherical Torus Experiment Upgrade (NSTX-U) at Princeton Plasma Physics Laboratory. The firmware has been upgraded to include real-time digital filtering, which enables continuous acquisition of the Doppler back-scattered active probing data. In this poster we shall present SAMI's analysis of the plasma edge on NSTX-U including measurements of the edge pitch angle on NSTX-U using SAMI's unique 2-D Doppler-backscattering capability.

  12. Analysis of conductive target influence in plasma jet experiments through helium metastable and electric field measurements

    Science.gov (United States)

    Darny, T.; Pouvesle, J.-M.; Puech, V.; Douat, C.; Dozias, S.; Robert, Eric

    2017-04-01

    The use of cold atmospheric pressure plasma jets for in vivo treatments implies most of the time plasma interaction with conductive targets. The effect of conductive target contact on the discharge behavior is studied here for a grounded metallic target and compared to the free jet configuration. In this work, realized with a plasma gun, we measured helium metastable HeM (23S1) concentration (by laser absorption spectroscopy) and electric field (EF) longitudinal and radial components (by electro-optic probe). Both diagnostics were temporally and spatially resolved. Mechanisms after ionization front impact on the target surface have been identified. The remnant conductive ionized channel behind the ionization front electrically transiently connects the inner high voltage electrode to the target. Due to impedance mismatching between the ionized channel and the target, a secondary ionization front is initiated and rapidly propagates from the target surface to the inner electrode through this ionized channel. This leads to a greatly enhanced HeM production inside the plasma plume and the capillary. Forward and reverse dynamics occur with further multi reflections of more or less damped ionization fronts between the inner electrode and the target as long as the ionized channel is persisting. This phenomenon is very sensitive to parameters such as target distance and ionized channel conductivity affecting electrical coupling between these two and evidenced using positive or negative voltage polarity and nitrogen admixture. In typical operating conditions for the plasma gun used in this work, it has been found that after the secondary ionization front propagation, when the ionized channel is conductive enough, a glow like discharge occurs with strong conduction current. HeM production and all species excitation, especially reactive ones, are then driven by high voltage pulse evolution. The control of forward and reverse dynamics, impacting on the production of the glow

  13. Rapid Atmospheric-Pressure-Plasma-Jet Processed Porous Materials for Energy Harvesting and Storage Devices

    Directory of Open Access Journals (Sweden)

    Jian-Zhang Chen

    2015-01-01

    Full Text Available Atmospheric pressure plasma jet (APPJ technology is a versatile technology that has been applied in many energy harvesting and storage devices. This feature article provides an overview of the advances in APPJ technology and its application to solar cells and batteries. The ultrafast APPJ sintering of nanoporous oxides and 3D reduced graphene oxide nanosheets with accompanying optical emission spectroscopy analyses are described in detail. The applications of these nanoporous materials to photoanodes and counter electrodes of dye-sensitized solar cells are described. An ultrashort treatment (1 min on graphite felt electrodes of flow batteries also significantly improves the energy efficiency.

  14. Microturbulence and Flow Shear in High-performance JET ITB Plasma

    Energy Technology Data Exchange (ETDEWEB)

    R.V. Budny; A. Andre; A. Bicoulet; C. Challis; G.D. Conway; W. Dorland; D.R. Ernst; T.S. Hahm; T.C. Hender; D. McCune; G. Rewoldt; S.E. Sharapov

    2001-12-05

    The transport, flow shear, and linear growth rates of microturbulence are studied for a Joint European Torus (JET) plasma with high central q in which an internal transport barrier (ITB) forms and grows to a large radius. The linear microturbulence growth rates of the fastest growing (most unstable) toroidal modes with high toroidal mode number are calculated using the GS2 and FULL gyrokinetic codes. These linear growth rates, gamma (subscript lin) are large, but the flow-shearing rates, gamma (subscript ExB) (dominated by the toroidal rotation contribution) are also comparably large when and where the ITB exists.

  15. Increase of the Density, Temperature and Velocity of Plasma Jets driven by a Ring of High Energy Laser Beams

    CERN Document Server

    Fu, Wen; Fatenejad, Milad; Lamb, Donald Q; Grosskopf, Michael; Park, Hye-Sook; Remington, Bruce; Spitkovsky, Anatoly

    2012-01-01

    Supersonic plasma outflows driven by multi-beam, high-energy lasers, such as Omega and NIF, have been and will be used as platforms for a variety of laboratory astrophysics experiments. Here we propose a new way of launching high density and high velocity, plasma jets using multiple intense laser beams in a hollow ring formation. We show that such jets provide a more flexible and versatile platform for future laboratory astrophysics experiments. Using high resolution hydrodynamic simulations, we demonstrate that the collimated jets can achieve much higher density, temperature and velocity when multiple laser beams are focused to form a hollow ring pattern at the target, instead of focused onto a single spot. We carried out simulations with different ring radii and studied their effects on the jet properties. Implications for laboratory collisionless shock experiments are discussed.

  16. Transport and micro-instability analysis of JET H-mode plasma during pellet fueling

    Science.gov (United States)

    Klaywittaphat, P.; Onjun, T.

    2017-02-01

    Transport and micro-instability analysis in a JET H-mode plasma discharge 53212 during the pellet fueling operation is carried out using the BALDUR integrated predictive modeling code with a combination of the NCLASS neoclassical transport model and an anomalous core transport model (either Mixed B/gB or MMM95 model). In this work, the evolution of plasma current, plasma density and temperature profiles is carried out and, consequently, the plasma’s behaviors during the pellet operation can be observed. The NGS pellet model with the Grad-B drift effect included is used to describe pellet ablation and its behaviors when a pellet is launched into hot plasma. The simulation shows that after each pellet enters the plasma, there is a strong perturbation on the plasma causing a sudden change of both thermal and particle profiles, as well as the thermal and particle transports. For the simulation using MMM95 transport model, the change of both thermal and particle transports during pellet injection are found to be dominated by the transport due to the resistive ballooning modes due to the increase of collisionality and resistivity near the plasma edge. For the simulation based on mixed B/gB transport model, it is found that the change of transport during the pellet injection is dominated by the Bohm term. Micro-instability analysis of the plasma during the time of pellet operation is also carried out for the simulations based on MMM95 transport model. It is found that the ion temperature gradient mode is destabilized due to an increase of temperature gradient in the pellet effective region, while the trapped electron mode is stabilized due to an increase of collisionality in that region.

  17. DNA damage in oral cancer and normal cells induced by nitrogen atmospheric pressure plasma jets

    Science.gov (United States)

    Han, Xu; Kapaldo, James; Liu, Yueying; Stack, M. Sharon; Ptasinska, Sylwia

    2015-09-01

    Nitrogen atmospheric pressure plasma jets (APPJs) have been shown to effectively induce DNA double strand breaks in SCC25 oral cancer cells. The APPJ source constructed in our laboratory operates based on dielectric barrier discharge. It consists of two copper electrodes alternatively wrapping around a fused silica tube with nitrogen as a feed gas. It is generally more challenging to ignite plasma in N2 atmosphere than in noble gases. However, N2 provides additional advantages such as lower costs compared to noble gases, thus this design can be beneficial for the future long-term clinical use. To compare the effects of plasma on cancer cells (SCC25) and normal cells (OKF), the cells from both types were treated at the same experimental condition for various treatment times. The effective area with different damage levels after the treatment was visualized as 3D maps. The delayed damage effects were also explored by varying the incubation times after the treatment. All of these studies are critical for a better understanding of the damage responses of cellular systems exposed to the plasma radiation, thus are useful for the development of the advanced plasma cancer therapy. The research described herein was supported by the Division of Chemical Sciences, Geosciences and Biosciences, Basic Energy Sciences, Office of Science, United States Department of Energy through Grant No. DE-FC02-04ER15533.

  18. Fluid-Plasma-Combustion Coupling Effects on the Ignition of a Fuel Jet

    Science.gov (United States)

    Massa, Luca; Freund, Jonathan

    2016-11-01

    We analyze the effect of plasma-combustion coupling on the ignition and flame supported by a DBD interacting with a jet of H2 in a air cross-flow. We propose that plasma-combustion coupling is due to the strong temperature-dependence of specific collisional energy loss as predicted by the Boltzmann equation, and that e- transport can be modeled by assuming a form for the E-field pulse in microstreamers. We introduce a two-way coupling based on the Boltzmann equation and the charged species conservation. The addition of this mechanism to a hydrogen combustion scheme leads to an improvement of the ignition prediction and of the understanding of the effect of the plasma on the flow. The key points of the analysis are 1) explanation of the mechanism for the two-stage ignition and quenching observed experimentally, 2) explanation of the existence of a power threshold above which the plasma is beneficial to the ignition probability, 3) understanding of the increase in power absorbed by the plasma in burning conditions and the reduction in power absorbed with an increase in the cross velocity, 4) explanation of the non-symmetric emissions and the increase in luminescence at the rotovibrational H2O band. The model is validated in part against air-H2 flow experiments. This material is based in part upon work supported by the Department of Energy, National Nuclear Security Administration, under Award Number DE-NA0002374.

  19. Interaction of DC Microhollow Cathode Discharge Plasma Micro Jet with Liquid Media

    Science.gov (United States)

    Zhu, Weidong; Lopez, Jose; Becker, Kurt

    2008-10-01

    There have been different approaches in studying the interaction between plasma and liquid, such as sustained plasmas in contact with liquids and pulsed electric discharge in liquids. Recently, we have discovered that stable plasma can be sustained within a gas cavity maintained inside liquid media. A prototype device with key dimensions in sub-millimeter range were operated successfully in de-ionized water and turbo molecular pump oil with ambient air, pure nitrogen or pure oxygen used as the operating gas. Hydrogen Peroxide production in de-ionized water with ambient air as the working gas is estimated to be about 80 mg/L after 15 minutes plasma jet-water interaction while energy consumption is only about 8-10 W. With the radicals readily generated and directly introduced into the liquid media, it could lead to applications such as in-liquid bio-waste treatment, bio-rich liquid modification, in-situ monitoring/sensing, and filtration of by-products from VOC treatment by plasma.

  20. Absolute production rate measurements of nitric oxide by an atmospheric pressure plasma jet (APPJ)

    Energy Technology Data Exchange (ETDEWEB)

    Pipa, A V; Bindemann, T; Foest, R; Kindel, E; Roepcke, J; Weltmann, K-D [Leibniz-Institut fuer Plasmaforschung and Technologie e.V. (INP), Felix-Hausdorff Strasse 2, D-17489 Greifswald (Germany)], E-mail: foest@inp-greifswald.de

    2008-10-07

    Tunable diode laser absorption spectroscopy (TDLAS) has been applied to measure the absolute production rate of NO molecules in the gas phase of an atmospheric pressure plasma jet (APPJ) operating at rf (13.56 MHz) in argon with small (up to 1%) admixtures of air. The resulting NO production rates were found to be in the range (0.1-80) x 10{sup -3} sccm or (0.05-35) x 10{sup 18} molecules s{sup -1} depending on the experimental conditions. Maximum rates were obtained at 0.2% air. For TDLAS measurements the APPJ was arranged inside an astigmatic multi-pass cell of Herriott type with 100 m absorption length. The insertion into a closed volume differs slightly from the normal, open operation with the jet propagating freely into air. Therefore, the measuring results are compared with optical emission of the open jet to verify equivalent experimental conditions. The dependence of the optical emission of NO (237 nm) on power and gas mixture has been measured. The similar shape of the dependence of absorption and emission signals gives evidence that the comparability of experimental conditions is sufficiently satisfied. It is concluded that the NO production rate of the APPJ in ambient air can be characterized using TDLAS and provides reliable results in spite of differing experimental conditions due to the set-up.

  1. Experimental and theoretical study of an atmospheric air plasma-jet

    Science.gov (United States)

    Xaubet, M.; Giuliani, L.; Grondona, D.; Minotti, F.

    2017-01-01

    In this work, we present an experimental and theoretical study of a low frequency, atmospheric plasma-jet discharge in air. Voltage-current characteristics and spectroscopic data were experimentally obtained, and a theoretical model developed to gain information of different aspects of the discharge. The discharge is modeled as a cathode layer with different mechanisms of electron emission and a main discharge channel that includes the most important kinetic reactions and species. From the electric measurements, it is determined that high electric field magnitudes are attained in the main channel, depending on the gas flow rate. Using the voltage-current characteristics as an input, the model allows to determine the plasma state in the discharge, including electron, gas, and molecular nitrogen vibrational temperatures. The model also allows to infer the mechanisms of secondary electron emission that sustain the discharge.

  2. Impurity line emission due to thermal charge exchange in JET edge plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Maggi, C.F.; Horton, L.D.; Koenig, R.; Stamp, M. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Summers, H.P. [Strathclyde Univ., Glasgow (United Kingdom)

    1994-07-01

    High n-shell emission from hydrogen-like carbon (C VI, n=8-7) has been routinely observed from the plasma edge of JET. By comparing the measured spectral line intensities with the signals predicted by advanced atomic physics modelling of carbon and hydrogen radiation, integrated with modelling of the divertor and edge plasma, it is concluded that charge transfer from excited state hydrogen donors into fully stripped carbon ions can account for the observed spectral emission, but that the hydrogen distribution and to a lesser extent the carbon distribution away from the strike zone predicted by the transport model are too low. Data presented are those of three upper X-point discharges, where the target material was carbon. 5 refs., 1 fig., 3 tabs.

  3. Thermodynamic study on the formation of acetylene during coal pyrolysis in the arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Bao, W.; Li, F.; Cai, G.; Lu, Y.; Chang, L. [Taiyuan University of Technology, Taiyuan (China)

    2009-07-01

    Based on the principle of minimizing the Gibbs free energy, the composition of C-H-O-N-S equilibrium system about acetylene formation during the pyrolysis in arc plasma jet for four kinds of different rank-ordered coals such as Datong, Xianfeng, Yangcheng, and Luan was analyzed and calculated. The results indicated that hydrogen, as the reactive atmosphere, was beneficial to the acetylene formation. The coal ranks and the hydrogen, oxygen, nitrogen, and sulfur in coal all could obviously affect the acetylene yield. The mole fraction of acetylene is the maximum when the ratio value of atom H/C was 2. The content of oxygen was related to the acetylene yield, but it does not compete with CO formation. These agreed with the experimental results, and they could help to select the coal type for the production of acetylene through plasma pyrolysis process.

  4. Gas mixing enhanced by power modulations in atmospheric pressure microwave plasma jet

    Science.gov (United States)

    Voráč, J.; Potočňáková, L.; Synek, P.; Hnilica, J.; Kudrle, V.

    2016-04-01

    Microwave plasma jet operating in atmospheric pressure argon was power modulated by audio frequency sine envelope in the 102 W power range. Its effluent was imaged using interference filters and ICCD camera for several different phases of the modulating signal. The combination of this fast imaging with spatially resolved optical emission spectroscopy provides useful insights into the plasmachemical processes involved. Phase-resolved schlieren photography was performed to visualize the gas dynamics. The results show that for higher modulation frequencies the plasma chemistry is strongly influenced by formation of transient flow perturbation resembling a vortex during each period. The perturbation formation and speed are strongly influenced by the frequency and power variations while they depend only weakly on the working gas flow rate. From application point of view, the perturbation presence significantly broadened lateral distribution of active species, effectively increasing cross-sectional area suitable for applications.

  5. Progress in Development of C60 Nanoparticle Plasma Jet for Diagnostic of Runaway Electron Beam-Plasma Interaction and Disruption Mitigation Study for ITER

    Science.gov (United States)

    Bogatu, I. N.; Thompson, J. R.; Galkin, S. A.; Kim, J. S.

    2013-10-01

    We produced a C60 nanoparticle plasma jet (NPPJ) with uniquely fast response-to-delivery time (~ 1 - 2 ms) and unprecedentedly high momentum (~ 0 . 6 g .km/s). The C60 NPPJ was obtained by using a solid state TiH2/C60 pulsed power cartridge producing ~180 mg of C60 molecular gas by sublimation and by electromagnetic acceleration of the C60 plasma in a coaxial gun (~35 cm length, 96 kJ energy) with the output of a high-density (>1023 m-3) hyper-velocity (>4 km/s) plasma jet. The ~ 75 mg C60/C plasma jet has the potential to rapidly and deeply deliver enough mass to significantly increase electron density (to ne ~ 2 . 4 ×1021 m-3, i.e. ~ 60 times larger than typical DIII-D pre-disruption value, ne 0 ~ 4 ×1019 m-3), and to modify the 'critical electric field' and the runaway electrons (REs) collisional drag during different phases of REs dynamics. The C60 NPPJ, as a novel injection technique, allows RE beam-plasma interaction diagnostic by quantitative spectroscopy of C ions visible/UV line intensity. The system is scalable to ~ 1 - 2 g C60/C plasma jet output and technology is adaptable to ITER acceptable materials (BN and Be) for disruption mitigation. Work supported by US DOE DE-FG02-08ER85196 grant.

  6. Pulsed microwave-driven argon plasma jet with distinctive plume patterns resonantly excited by surface plasmon polaritons

    Science.gov (United States)

    Chen, Zhao-Quan; Yin, Zhi-Xiang; Xia, Guang-Qing; Hong, Ling-Li; Hu, Ye-Lin; Liu, Ming-Hai; Hu, Xi-Wei; A. Kudryavtsev, A.

    2015-02-01

    Atmospheric lower-power pulsed microwave argon cold plasma jets are obtained by using coaxial transmission line resonators in ambient air. The plasma jet plumes are generated at the end of a metal wire placed in the middle of the dielectric tubes. The electromagnetic model analyses and simulation results suggest that the discharges are excited resonantly by the enhanced electric field of surface plasmon polaritons. Moreover, for conquering the defect of atmospheric argon filamentation discharges excited by 2.45-GHz of continued microwave, the distinctive patterns of the plasma jet plumes can be maintained by applying different gas flow rates of argon gas, frequencies of pulsed modulator, duty cycles of pulsed microwave, peak values of input microwave power, and even by using different materials of dielectric tubes. In addition, the emission spectrum, the plume temperature, and other plasma parameters are measured, which shows that the proposed pulsed microwave plasma jets can be adjusted for plasma biomedical applications. Project supported by the National Natural Science Foundation of China (Grant Nos. 11105002 and 61170172), the Natural Science Foundation of Anhui Province, China (Grant Nos. 1408085QA16 and 1408085ME101), the China Postdoctoral Science Foundation (Grant No. 2014M551788), and the Open-end Fund of State Key Laboratory of Advanced Electromagnetic Engineering and Technology (HUST), China (Grant No. GZ1301).

  7. Modification of tapioca starch by non-chemical route using jet atmospheric argon plasma.

    Science.gov (United States)

    Wongsagonsup, Rungtiwa; Deeyai, Panakamol; Chaiwat, Weerawut; Horrungsiwat, Sawanee; Leejariensuk, Kesini; Suphantharika, Manop; Fuongfuchat, Asira; Dangtip, Somsak

    2014-02-15

    Non-chemical modification of tapioca starch was investigated using jet atmospheric argon plasma treatment. Two forms of starch slurry, i.e. granular starch (G) and cooked starch (C), were jet-treated by argon plasma generated by supplying input power of 50 W (denoted as G50 and C50 samples) and 100 W (denoted as G100 and C100 samples) for 5 min. Physical, rheological, and structural characteristics of the modified starch were investigated. The G50 and C100 samples had lower paste clarity but higher thermal stability and performed stronger gels (G50 only) compared to their control counterparts. On the other hand, the analyzed properties of the G100 and C50 samples showed the opposite trend. FTIR and (1)H NMR results revealed that the relative areas of COC and OH peaks were changed after the treatment. Cross-linking reaction seemed to predominantly take place for the G50 and C100 samples, whereas depolymerization predominated for the G100 and C50 samples.

  8. Experimental investigation of photoresist etching by kHz AC atmospheric pressure plasma jet

    Science.gov (United States)

    Wang, Lijun; Zheng, Yashuang; Wu, Chen; Jia, Shenli

    2016-11-01

    In this study, the mechanism of the photoresist (PR) etching by means of a kHz AC atmospheric pressure plasma jet (APPJ) is investigated. The scanning electron (SEM) and the polarizing microscope are used to perform the surface analysis, and the mechanical profilometry is applied to diagnose the etch rate. The results show that granulated structure with numerous microparticles appears at the substrate surface after APPJ treatment, and the etch rate in the etch center is the fastest and gradually slows down to the edge of etch region. In addition, the pin-ring electrode APPJ has the highest etch rate at but easy to damage the Si wafer, the double-ring APPJ is the most stable but requires long time to achieve the ideal etch result, and the etch rate and the etch result of the multi-electrode APPJ fall in between. Ar APPJ had much higher PR etch rate and more irregular etch trace than He APPJ. It is speculated that Ar APPJ is more energetic and effective in transferring reactive species to the PR surface. It is also observed that the effective etch area initially increases and then decreases as plasma jet outlet to the PR surface distance increases.

  9. Feed gas humidity: a vital parameter affecting a cold atmospheric-pressure plasma jet and plasma-treated human skin cells

    Science.gov (United States)

    Winter, J.; Wende, K.; Masur, K.; Iseni, S.; Dünnbier, M.; Hammer, M. U.; Tresp, H.; Weltmann, K.-D.; Reuter, S.

    2013-07-01

    In this study, the effect of feed gas humidity on the reactive component generation of an atmospheric-pressure argon plasma jet and its effect on human skin cells are investigated. Feed gas humidity is identified as one key parameter that strongly influences stability and reproducibility of plasma medical studies. The plasma jet is investigated by absorption spectroscopy in the ultraviolet and infrared spectral region for its ozone production depending on the humidity concentration in the feed gas. By optical emission spectroscopy the dependence of present excited plasma species such as hydroxyl radicals, molecular nitrogen, argon and atomic oxygen on the feed gas humidity is investigated. As an interface layer between the plasma jet effluent and the biological cell, a buffer solution is treated and the hydrogen peroxide (H2O2) production is studied with two independent colorimetric assays as a function of humidity admixture to the feed gas. Ultimately, the effect of varying feed gas humidity on the cell viability of indirect plasma treated adherent HaCAT cells is investigated. The highest viability is found for the driest feed gas condition. Furthermore, this work shows answers for the relevance of unwanted—or intended—feed gas humidity in plasma medical experiments and their comparatively large relevance with respect to ambient humidity. The findings will lead to more reproducible experiments in the field of plasma medicine.

  10. Numerical study of secondary electron emission in a coaxial radio-frequency driven plasma jet at atmospheric pressure

    CERN Document Server

    Hemke, Torben; Wollny, Alexander; Brinkmann, Ralf Peter; Mussenbrock, Thomas

    2011-01-01

    In this work we investigate a numerical model of a coaxial RF-driven plasma jet operated at atmospheric pressure. Due to the cylindrical symmetry an adequate 2-D representation of the otherwise 3-dimensional structure is used. A helium-oxygen chemistry reaction scheme is applied. We study the effect of secondary electrons emitted at the inner electrode as well as the inserted dielectric tube and discuss their impact on the discharge behavior. We conclude that a proper choice of materials can improve the desired mode of operation of such plasma jets in terms of materials and surface processing.

  11. Dual effects of atmospheric pressure plasma jet on skin wound healing of mice.

    Science.gov (United States)

    Xu, Gui-Min; Shi, Xing-Min; Cai, Jing-Fen; Chen, Si-Le; Li, Ping; Yao, Cong-Wei; Chang, Zheng-Shi; Zhang, Guan-Jun

    2015-01-01

    Cold plasma has become an attractive tool for promoting wound healing and treating skin diseases. This article presents an atmospheric pressure plasma jet (APPJ) generated in argon gas through dielectric barrier discharge, which was applied to superficial skin wounds in BALB/c mice. The mice (n = 50) were assigned randomly into five groups (named A, B, C, D, E) with 10 animals in each group. Natural wound healing was compared with stimulated wound healing treated daily with APPJ for different time spans (10, 20, 30, 40, and 50 seconds) on 14 consecutive days. APPJ emission spectra, morphological changes in animal wounds, and tissue histological parameters were analyzed. Statistical results revealed that wound size changed over the duration of the experimental period and there was a significant interaction between experimental day and group. Differences between group C and other groups at day 7 were statistically significant (p plasma could inactivate bacteria around the wound, activate fibroblast proliferation in wound tissue, and eventually promote wound healing. Whereas, over doses of plasma suppressed wound healing due to causing cell death by apoptosis or necrosis. Both positive and negative effects may be related to the existence of reactive oxygen and nitrogen species (ROS and RNS) in APPJ.

  12. Mechanisms behind surface modification of polypropylene film using an atmospheric-pressure plasma jet

    Science.gov (United States)

    Shaw, David; West, Andrew; Bredin, Jerome; Wagenaars, Erik

    2016-12-01

    Plasma treatments are common for increasing the surface energy of plastics, such as polypropylene (PP), to create improved adhesive properties. Despite the significant differences in plasma sources and plasma properties used, similar effects on the plastic film can be achieved, suggesting a common dominant plasma constituent and underpinning mechanism. However, many details of this process are still unknown. Here we present a study into the mechanisms underpinning surface energy increase of PP using atmospheric-pressure plasmas. For this we use the effluent of an atmospheric-pressure plasma jet (APPJ) since, unlike most plasma sources used for these treatments, there is no direct contact between the plasma and the PP surface; the APPJ provides a neutral, radical-rich environment without charged particles and electric fields impinging on the PP surface. The APPJ is a RF-driven plasma operating in helium gas with small admixtures of O2 (0-1%), where the effluent propagates through open air towards the PP surface. Despite the lack of charged particles and electric fields on the PP surface, measurements of contact angle show a decrease from 93.9° to 70.1° in 1.4 s and to 35° in 120 s, corresponding to a rapid increase in surface energy from 36.4 mN m-1 to 66.5 mN m-1 in the short time of 1.4 s. These treatment effects are very similar to what is found in other devices, highlighting the importance of neutral radicals produced by the plasma. Furthermore, we find an optimum percentage of oxygen of 0.5% within the helium input gas, and a decrease of the treatment effect with distance between the APPJ and the PP surface. These observed effects are linked to two-photon absorption laser-induced fluorescence spectroscopy (TALIF) measurements of atomic oxygen density within the APPJ effluent which show similar trends, implying the importance of this radical in the surface treatment of PP. Analysis of the surface reveals a two stage mechanism for the production of polar

  13. Deposition of hybrid organic-inorganic composite coatings using an atmospheric plasma jet system.

    Science.gov (United States)

    Dembele, Amidou; Rahman, Mahfujur; Reid, Ian; Twomey, Barry; MacElroy, J M Don; Dowling, Denis P

    2011-10-01

    The objective of this study is to investigate the influence of alcohol addition on the incorporation of metal oxide nanoparticles into nm thick siloxane coatings. Titanium oxide (TiO2) nanoparticles with diameters of 30-80 nm were incorporated into an atmospheric plasma deposited tetramethylorthosilicate (TMOS) siloxane coating. The TMOS/TiO2 coating was deposited using the atmospheric plasma jet system known as PlasmaStream. In this system the liquid precursor/nanoparticle mixture is nebulised into the plasma. It was observed that prior to being nebulised the TiO2 particles agglomerated and settled over time in the TMOS/TiO2 mixture. In order to obtain a more stable nanoparticle/TMOS suspension the addition of the alcohols methanol, octanol and pentanol to this mixture was investigated. The addition of each of these alcohols was found to stabilise the nanoparticle suspension. The effect of the alcohol was therefore assessed with respect to the properties of the deposited coatings. It was observed that coatings deposited from TMOS/TiO2, with and without the addition of methanol were broadly similar. In contrast the coatings deposited with octanol and pentanol addition to the TMOS/TiO2 mixture were significantly thicker, for a given set of deposition parameters and were also more homogeneous. This would indicate that the alcohol precursor was incorporated into the plasma polymerised siloxane. The incorporation of the organic functionality from the alcohols was confirmed from FTIR spectra of the coatings. The difference in behaviour with alcohol type is likely to be due to the lower boiling point of methanol (65 degrees C), which is lower than the maximum plasma temperature measured at the jet orifice (77 degrees C). This temperature is significantly lower than the 196 degrees C and 136 degrees C boiling points of octanol and pentanol respectively. The friction of the coatings was determined using the Pin-on-disc technique. The more organic coatings deposited with

  14. Synthetic aperture microwave imaging with active probing for fusion plasma diagnostics

    CERN Document Server

    Shevchenko, Vladimir F; Freethy, Simon J; Huang, Billy K

    2012-01-01

    A Synthetic Aperture Microwave Imaging (SAMI) system has been designed and built to obtain 2-D images at several frequencies from fusion plasmas. SAMI uses a phased array of linearly polarised antennas. The array configuration has been optimised to achieve maximum synthetic aperture beam efficiency. The signals received by antennas are down-converted to the intermediate frequency range and then recorded in a full vector form. Full vector signals allow beam focusing and image reconstruction in both real time and a post processing mode. SAMI can scan over 16 preprogrammed frequencies in the range of 10-35GHz with a switching time of 300ns. The system operates in 2 different modes simultaneously: both a passive imaging of plasma emission and also an active imaging of the back-scattered signal of the radiation launched by one of the antennas from the same array. This second mode is similar to so-called Doppler backscattering (DBS) reflectometry with 2-D resolution of the propagation velocity of turbulent structur...

  15. A linear-field plasma jet for generating a brush-shaped laminar plume at atmospheric pressure

    Science.gov (United States)

    Li, Xuechen; Li, Jiyuan; Chu, Jingdi; Zhang, Panpan; Jia, Pengying

    2016-06-01

    A linear-field plasma jet