Pinellas Plant facts. [Products, processes, laboratory facilities

Energy Technology Data Exchange (ETDEWEB)

1986-09-01

This plant was built in 1956 in response to a need for the manufacture of neutron generators, a principal component in nuclear weapons. The neutron generators consist of a miniaturized linear ion accelerator assembled with the pulsed electrical power supplies required for its operation. The ion accelerator, or neutron tube, requires ultra clean, high vacuum technology: hermetic seals between glass, ceramic, glass-ceramic, and metal materials: plus high voltage generation and measurement technology. The existence of these capabilities at the Pinellas Plant has led directly to the assignment of the lightning arrester connector, specialty capacitor, vacuum switch, and crystal resonator. Active and reserve batteries and the radioisotopically-powered thermoelectric generator draw on the materials measurement and controls technologies which are required to ensure neutron generator life. A product development and production capability in alumina ceramics, cermet (electrical) feedthroughs, and glass ceramics has become a specialty of the plant; the laboratories monitor the materials and processes used by the plant's commercial suppliers of ferroelectric ceramics. In addition to the manufacturing facility, a production development capability is maintained at the Pinellas Plant.

Environmental monitoring report, 1978: Pinellas Plant

International Nuclear Information System (INIS)

1979-04-01

Effluent and environmental monitoring programs maintained by the Pinellas Plant are designed to determine efficiencies of treatment and control mechanisms; to provide measurements of discharge concentrations for comparison with applicable standards; and to assess the concentrations of these discharges in the environment. Small quantities of tritium gas, tritium oxide and krypton-85 gas were released from the plant during the year. Average maximum ground level concentrations of these radioisotopes were all significantly less than 1/10 of 1 percent of the recommended guide for continuous nonoccupational exposure. Off-site releases of liquid effluents were analyzed for compliance with NPDES permit issues for this site by the U.S. Environmental protection Agency. Analyses were performed fo biochemical oxygen demand, suspended solids, fecal coliform bacteria, pH, nitrogen, phosphorus, arsenic, chlorides, chromium, copper, cyanides, detergents, fluorides, iron, lead, mercury, oil plus greases, phenols, turbidity and zinc. All results with the exception of suspended solids were well within permit limits. Site perimeter and off-site air samples for tritium gas and tritium oxide, as well as off-site surface water samples obtained to distances of 9.6 kilometers from the plant site and analyzed for tritium content, showed levels significantly less than 1/10 of 1 percent of the recommended guide for continuous nonoccupational exposure. Calculations were made to determine the radiation doses resulting from releases of tritium oxide and krypton-85 to: an individual at the site boundary; individuals in the closest residential area; and the population within 80 kilometers of the plant site. Calculated doses are exceedingly small when compared to the recommended standards. The total dose commitment to the population residing within 80 kilometers was determined to be 0.40 man-rem as compared to annual dose from natural radiation of 210,747 man-rem

Environmental monitoring report, 1980: Pinellas Plant

International Nuclear Information System (INIS)

1981-03-01

Results of the monitoring program at the Pinellas Plant are described. Small quantities of tritium gas, tritium oxide, carbon-14 labeled solvent and krypton-85 gas were released from the plant during the year. Average maximum ground level concentrations of these radioisotopes were all significantly less than 0.1% of the recommended guide for continuous nonoccupational exposure. Off-site releases of liquid effluents were analyzed for compliance with the National Pollutant Discharge Elimination System (NPDES). Analyses were performed for biochemical oxygen demand, suspended solids, fecal coliform bacteria, pH, nitrogen, phosphorus, arsenic, chlorides, chromium, copper, cyanides, detergents, fluorides, iron, lead, mercury, oil plus greases, phenols, turbidity, and zinc. In addition to the non-radioactive parameters listed above, a small quantity of radioactive tritium oxide was released in the effluent. Analyses showed the average concentration was 0.20% of the nonoccupational exposure guide. Site perimeter and off-site air samples for tritium gas and tritium oxide, as well as off-site surface water samples obtained to distance of 9.6 kilometers (6 miles) from the plant site and analyzed for tritium content, showed levels significantly less than 0.1% of the recommended guide for continuous nonoccupational exposure. Small sealed plutonium sources containing approximately 80% plutonium-238 oxide and 20% plutonium-239 oxide and other isotopes, are utilized at this site. No plutonium was released to the environment.Calculations were made to determine the radiation doses resulting from releases of tritium oxide, 85 Kr, and 14 C to: an individual at the site boundary; individuals in the closest residential area; and the population within 80 kilometers (50 miles) of the plant site. The total dose commitment to the population residing within 80 kilometers was determined to be 0.55 man-rem as compared to the annual dose from natural radiation of 223,165 man-rem

Pinellas Plant environmental monitoring report, 1981

International Nuclear Information System (INIS)

1982-03-01

The effluent and environmental monitoring programs maintained by the Pinellas Plant are designed to determine the efficiencies of treatment and control mechanisms, to provide measurements of discharge concentrations for comparison with applicable standards, and to assess the concentrations of these discharges in the environment. Small quantities of tritium gas, tritium oxide, carbon-14 labeled solvent and krypton-85 gas were released from the plant during the year. Average maximum ground level concentrations of these radioisotopes were all significantly less than 1/10 of 1% of the standard for continuous nonoccupational exposure. Off-site releases of liquid effluents were analyzed for compliance with the National Pollutant Discharge Elimination System (NPDES) permit issued for this site. Analyses were performed for biochemical oxygen demand, suspended solids, fecal coliform bacteria, pH, nitrogen, phosphorus, arsenic, chlorides, chromium, copper, cyanides, detergents, fluorides, iron, lead, mercury, oil plus greases, phenols, turbidity and zinc. Excursions above permit limits were experienced in the results for suspended solids, fecal coliforms, iron and mercury. In addition to the non-radioactive parameters listed, a small quantity of radioactive tritium oxide was released in the effluent. Analyses showed the average concentration was 0.43% of the nonoccupational standard. Site perimeter and off-site air samples for tritium gas and tritium oxide, as well as off-site surface water samples obtained to distance of 9.6 kilometers from the plant site and analyzed for tritium content, showed levels significantly less than 1/10 of 1% of the standard for continuous nonoccupational exposure. Calculation were made to determine the radiation doses resulting from releases of tritium oxide, krypton-85 and carbon-14 to: an individual at the site boundary; individuals in the closest residential area; and the population within 80 kilometers (50 miles) of the plant site

Environmental Survey preliminary report, Pinellas Plant, Largo, Florida

International Nuclear Information System (INIS)

1987-11-01

The purpose of this report is to present the preliminary findings made during the Environmental Survey, conducted May 11 through 22, 1987, at the United States Department of Energy (DOE) Pinellas Plant in Largo, Florida. As a Preliminary Report, the contents are subject to revisions, which will be made in a forthcoming Interim Report, based on Albuquerque Operations Office review and comments on technical accuracy, the results of the sampling and analyses, and other information that may come to the Survey team's attention prior to issuance of the Interim Report. The Pinellas Plant is currently operated for DOE by the General Electric Company-Neutron Devices Department (GENDD). The Pinellas Survey is part of the larger DOE-wide Environmental Survey effort announced by Secretary John S. Herrington on September 18, 1985. The purpose of this effort is to identify, via ''no fault'' baseline Surveys, existing environmental problems are areas of environmental risk at DOE facilities and to rank them on a DOE-wide basis. This ranking will enable DOE to more effectively establish priorities for addressing environmental problems and allocate the resources necessary to correct these problems. Because the Survey is ''no fault'' and is not an ''audit,'' it is not designed to identify specific isolated incidents of noncompliance or to analyze environmental management practices. Such incidents and/or management practices will, however, be used in the Survey as a means of identifying existing and potential environmental problems. 55 refs., 37 figs., 37 tabs

Environmental Survey preliminary report, Pinellas Plant, Largo, Florida

Energy Technology Data Exchange (ETDEWEB)

1987-11-01

The purpose of this report is to present the preliminary findings made during the Environmental Survey, conducted May 11 through 22, 1987, at the United States Department of Energy (DOE) Pinellas Plant in Largo, Florida. As a Preliminary Report, the contents are subject to revisions, which will be made in a forthcoming Interim Report, based on Albuquerque Operations Office review and comments on technical accuracy, the results of the sampling and analyses, and other information that may come to the Survey team's attention prior to issuance of the Interim Report. The Pinellas Plant is currently operated for DOE by the General Electric Company-Neutron Devices Department (GENDD). The Pinellas Survey is part of the larger DOE-wide Environmental Survey effort announced by Secretary John S. Herrington on September 18, 1985. The purpose of this effort is to identify, via no fault'' baseline Surveys, existing environmental problems are areas of environmental risk at DOE facilities and to rank them on a DOE-wide basis. This ranking will enable DOE to more effectively establish priorities for addressing environmental problems and allocate the resources necessary to correct these problems. Because the Survey is no fault'' and is not an audit,'' it is not designed to identify specific isolated incidents of noncompliance or to analyze environmental management practices. Such incidents and/or management practices will, however, be used in the Survey as a means of identifying existing and potential environmental problems. 55 refs., 37 figs., 37 tabs.

Independent technical review of the Pinellas Plant

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

This report documents an Independent Technical Review (ITR) of facilities, organizations, plans, activities and various other elements required to successfully transition the Pinellas Plant from Defense Program (DP) funded operation to either community developed reuse or safe deactivation leading to decontamination and decommissioning (D&D). The review was conducted at the request of the Department of Energy (DOE) Deputy Assistant Secretary for Facility Transition and Management (EM-60) and is a consensus of the nine member ITR Team.

In Situ Thermal NAPL Remediation at the Northeast Site Pinellas Environmental Restoration Project

International Nuclear Information System (INIS)

Juhlin, R.; Butherus, M.

2006-01-01

The U.S. Department of Energy (DOE) is conducting thermal remediation to remove non-aqueous phase liquids (NAPLs) from the subsurface at the Northeast Site that is part of the Pinellas Environmental Restoration Project. The Northeast Site is located on the Young - Rainey Science, Technology, and Research (STAR) Center in Largo, Florida. The STAR Center was formerly a DOE facility. The NAPL remediation was performed at Area A and is currently being performed at Area B at the Northeast Site. The remediation at Area A was completed in 2003 and covered an area of 900 m 2 (10,000 ft 2 ) and a depth of remediation that extended to 10.7 m (35 ft) below ground surface. Cleanup levels achieved were at or below maximum contaminant levels in almost all locations. The remediation project at Area B is ongoing and covers an area of 3,240 m 2 (36,000 ft 2 ), a volume of 41,300 m (54,000 yd 3), and a depth of remediation to 12 m (40 ft) below ground surface. In addition, a portion of the subsurface under an occupied building in Area B is included in the remediation. The cleanup levels achieved from this remediation will be available in the Area B Final Report that will be posted on the DOE Office of Legacy Management web site (www.lm.doe.gov/land/sites/fl/ pinellas/pinellas.htm) in January 2007. Electrical resistive heating and steam were the chosen remediation methods at both areas. Lessons learned from the Area A remediation were incorporated into the Area B remediation and could benefit managers of similar remediation projects. (authors)

Environmental Assessment for decontamination and dismantlement, Pinellas Plant

International Nuclear Information System (INIS)

1995-06-01

The US Department of Energy (DOE) has prepared an Environmental Assessment (EA) (DOE/EA-1092) of the proposed decontamination and dismantlement of the Pinellas Plant in Largo, Florida. Under the Decontamination and Dismantlement EA, the DOE proposes to clean up facilities, structures, and utilities; dismantle specific structures; and mitigate or eliminate any environmental impacts associated with the cleanup, dismantlement, and related activities. Related activities include utilization of specific areas by new tenants prior to full-scale cleanup. Based on the analyses in the EA, the DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act of 1969. Therefore, the preparation of an environmental impact statement is not required. This report contains the Environmental Assessment, as well as the Finding of No Significant Impact (FONSI)

Pinellas County, Florida, Site Environmental Restoration Project Sitewide Environmental Monitoring Semiannual Progress Report for the Young - Rainey STAR Center June Through November 2016, January 2017

Energy Technology Data Exchange (ETDEWEB)

Surovchak, Scott [USDOE Office of Legacy Management, Washington, DC (United States); Daniel, Joe [Navarro Research and Engineering, Inc., Oak Ridge, TN (United States)

2017-01-01

The Young - Rainey STAR Center (Science, Technology, and Research Center) at the Pinellas County, Florida, Site is a former U.S. Department of Energy (DOE) facility constructed in the mid-1950s. The 96-acre STAR Center is located in Largo, Florida, and lies in the northeast quarter of Section 13, Township 30 South, Range 15 East (Figure 1). While it was owned by DOE, the purpose of the site was to develop and manufacture components for the nation’s nuclear weapons program. In 1987, the U.S. Environmental Protection Agency (EPA) performed a Resource Conservation and Recovery Act Facility Assessment (EPA 1988) at the site to gather information on potential releases of hazardous materials. In February of 1990, EPA issued a Hazardous and Solid Waste Amendments permit to DOE, requiring DOE to investigate and perform remediation activities in those areas designated as solid-waste management units (SWMUs) contaminated by hazardous materials resulting from DOE operations. A total of 17 SWMUs were identified and investigated at the STAR Center. By 1997, 13 of the 17 SWMUs had been remediated or approved for no further action. More recently, the Florida Department of Environmental Protection (FDEP) executed Conditional Site Rehabilitation Completion Orders for the Northeast Site and the Wastewater Neutralization Area on July 27, 2016, stating that no further action is required for those SWMUs. The Building 100 Area (a combination of the Old Drum Storage Site and the Building 100-Industrial Drain Leaks SWMUs) comprises the only two active SWMUs at the STAR Center (Figure 2). This document serves as the semiannual progress report for the SWMUs by providing the results of recent monitoring activities and a summary of ongoing and projected work. The STAR Center is owned by the Pinellas County Industrial Development Authority, but DOE is responsible for remediation activities at the site. Additional background information for the site is contained in the Long-Term Surveillance

INDEPENDENT TECHNICAL REVIEW OF THE BUILDING 100 PLUME, FORMER DOE PINELLAS SITE (YOUNG - RAINEY STAR CENTER), LARGO, FLORIDA

Energy Technology Data Exchange (ETDEWEB)

Eddy-Dilek, C.; Rossabi, J.; Amidon, M.; Riha, B.; Kaback, D.

2010-07-30

Contaminated groundwater associated with Building 100 at the Young-Rainey Science, Technology, and Research Center, formerly the DOE Pinellas plant, is the primary remedial challenge that remains to be addressed at the site. Currently, Building 100 is an active industrial facility that is now owned and operated by the Pinellas county government. Groundwater samples collected from monitoring wells recently installed near the southern boundary of the site suggest that contaminated groundwater has migrated off the plant site. In response to the challenges presented by the Building 100 plume, the Office of Legacy Management (LM) requested assistance from the DOE Office of Groundwater and Soil Remediation (EM-32) to provide a review team to make technical recommendations so that they can efficiently and effectively address characterization and remediation of the plume. The review team was unanimous in the conclusion that a dynamic strategy that combines a phased implementation of direct push samplers, sensors, and tools can be used to better delineate the extent of contamination, control plume migration, and rapidly remediate the contaminated groundwater at the site. The initial efforts of the team focused on reviewing the site history and data, organizing the information into a conceptual model, identifying appropriate technologies, and recommending an integrated strategy. The current groundwater data from the site indicate a two-lobed plume extending to the east and south. To the east vinyl chloride is the primary contaminant of concern, to the south, vinyl chloride and cis1, 2-DCE are the primary contaminants. The limited data that are available suggest that reductive dechlorination of the TCE is already occurring but is not sufficient to prevent offsite migration of low concentrations of TCE daughter products. The team recommends that DOE pursue a strategy that builds on the natural cleansing capacity of the subsurface with reductive methods including biostimulation

Pinellas Plant: Child Care/Partnership School safety assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-11-01

The Albuquerque Operations Office through the Pinellas Plant Area Office is involved in a joint venture to establish a Partnership School and a Day Care Facility at the Plant. The venture is unique in that it is based on a partnership with the local county school system. The county school system will provide the teachers, supplies and classroom furnishings for the operation of the school for pre-kindergarten, kindergarten, first and second grade during regular school hours. The Government will provide the facility and its normal operating and maintenance costs. A Day Care Facility will also be available for children from infancy through the second grade for outside school hours. The day care will be operated as a non-profit corporation. Fees paid by parents with children in the day care center will cove the cost of staff, food, supplies and liability insurance. Again, the government will provide the facility and its normal operating and maintenance costs. Between 75 and 90 children are expected in the first year of operation. The Partnership School will consist of one class each for pre-kindergarten, kindergarten and first grade. Second grade will be added in 1990. The total estimated number of children for both the Child Care and Partnership School should not exceed 200 children. Expected benefits include reduced absenteeism, tardiness and turnover and thus increased productivity. The program will be an asset in recruiting and retaining the best workforce. Other benefits include improved education for the children.

Hydrogeology and Analysis of Aquifer Characteristics in West-Central Pinellas County, Florida

National Research Council Canada - National Science Library

Broska, James C; Barnette, Holly L

1999-01-01

The U.S. Geological Survey, in cooperation with Pinellas County, Florida, conducted an investigation to describe the hydrogeology and analyze the aquifer characteristics in west-central Pinellas County...

Radiological dose assessment of Department of Energy Pinellas Plant waste proposed for disposal at Laidlaw Environmental Services of South Carolina, Inc

International Nuclear Information System (INIS)

Socolof, M.L.; Lee, D.W.

1996-05-01

The U.S. Department of Energy (DOE) Pinellas Plant in Largo, FL is proposing to ship and dispose of hazardous sludge, listed as F006 waste, to the Laidlaw Environmental Services of South Carolina, Inc. (Laidlaw) treatment, storage, and disposal facility in Pinewood, South Carolina. This sludge contains radioactive tritium in concentrations of about 28 pCi/g. The objective of this study is to assess the possible radiological impact to workers at the Laidlaw facility and members of the public due to the handling, processing, and burial of the DOE waste containing tritium

Radiological dose assessment of Department of Energy Pinellas Plant waste proposed for disposal at Laidlaw Environmental Services of South Carolina, Inc.

Energy Technology Data Exchange (ETDEWEB)

Socolof, M.L.; Lee, D.W.

1996-05-01

The U.S. Department of Energy (DOE) Pinellas Plant in Largo, FL is proposing to ship and dispose of hazardous sludge, listed as F006 waste, to the Laidlaw Environmental Services of South Carolina, Inc. (Laidlaw) treatment, storage, and disposal facility in Pinewood, South Carolina. This sludge contains radioactive tritium in concentrations of about 28 pCi/g. The objective of this study is to assess the possible radiological impact to workers at the Laidlaw facility and members of the public due to the handling, processing, and burial of the DOE waste containing tritium.

Pinellas Plant environmental monitoring report, 1983

International Nuclear Information System (INIS)

1984-04-01

The results of the effluent and environmental monitoring programs are presented. Small quantities of tritium gas, tritium oxide, carbon-14 labeled solvent and krypton-85 gas were released from the plant during the year. Average maximum ground level concentrations of these radioisotopes were all less than 3/10 of 1 percent of the standard for continuous nonoccupational exposure. The plant's combined sanitary and industrial liquid effluents were analyzed for arsenic, barium, biochemical oxygen demand, boron, cadmium, total chromium, trivalent chromium, hexavalent chromium, copper, cyanide, iron, lead, manganese, mercury, nickel, phenolics, selenium, silver, sulfides, suspended solids and zinc. Small quantities of radioactive tritium were released to the POTW and from the East Pond. Analyses showed the levels were less than 1/10 of one percent of the applicable standards. Site perimeter and off-site air samples for tritium gas and tritium oxide, as well as off-site surface water samples obtained to distance of 9.6 kilometers (6 miles) from the plant site and analyzed for tritium content, showed levels significantly less than 1/10 of 1 percent of the standard for continuous nonoccupational exposure. Calculations were made to determine the radiation doses resulting from releases of tritium oxide, krypton-85 and carbon-14. The calculated doses are exceedingly small when compared to the applicable standards. The total dose commitment to the population residing within 80 kilometers (50 miles) was determined to be 0.40 man-rem as compared to the annual dose from natural radiation of 243,117 man-rem. 10 references, 3 figures, 12 tables

Bioinjection Performance Review for the Building 100 Area and 4.5 Acre Site at the Pinellas County, Florida, Site

Energy Technology Data Exchange (ETDEWEB)

Survochak, Scott [US Department of Energy, Washington, DC (United States). Office of Legacy Management; Daniel, Joe [Navarro Research and Engineering, Oak Ridge, TN (United States)

2016-05-01

This document provides a summary of a review of the performance of bioinjection activities at the Building 100 Area and the 4.5 Acre Site at the Pinellas County, Florida, Site since 2010, determines how best to optimize future injection events, and identifies the approach for the bioinjection event in 2016 at (1) the 4.5 Acre Site and (2) the Essentra property at the Building 100 Area. Because this document describes the next bioinjection event at the 4.5 Acre Site, it also serves as an addendum to the Interim Remedial Action Plan for Emulsified Edible Oil Injection at the 4.5 Acre Site (DOE 2013). In addition, this document revises the injection layout and injection intervals for the Essentra property that were originally described in the Interim Corrective Measure Work Plan for Source and Plume Treatment at the Building 100 Area (DOE 2014), and is a de facto update of that document. Bioinjection consists of injection of emulsified vegetable oil (EVO) and the microorganism Dehalococcoides mccartyi (DHM; formerly known as Dehalococcoides ethenogenes) into the subsurface to enhance biodegradation of trichloroethene (TCE), dichloroethene (DCE), and vinyl chloride (VC). VC is the only contaminant that exceeds its maximum contaminant level (10 micrograms per liter onsite and 1 microgram per liter onsite) on the 4.5 Acre Site and the Essentra property. Bioinjection was conducted at the 4.5 Acre Site in 2010 and 2013. Approximately 49,900 gallons of EVO and DHM were injected at 95 injection points in February 2010, and approximately 22,900 gallons of EVO and DHM were injected at 46 injection points in July 2013. The injection locations are shown on Figure 1. The goal of bioinjection at the 4.5 Acre Site is to decrease contaminant concentrations to maximum contaminant levels along the west and southwest property boundaries (to meet risk–based corrective action requirements) and to minimize the extent of the contaminant plume in the interior of the site. Bioinjection was

Implementation of a fully automated process purge-and-trap gas chromatograph at an environmental remediation site

International Nuclear Information System (INIS)

Blair, D.S.; Morrison, D.J.

1997-01-01

The AQUASCAN, a commercially available, fully automated purge-and-trap gas chromatograph from Sentex Systems Inc., was implemented and evaluated as an in-field, automated monitoring system of contaminated groundwater at an active DOE remediation site in Pinellas, FL. Though the AQUASCAN is designed as a stand alone process analytical unit, implementation at this site required additional hardware. The hardware included a sample dilution system and a method for delivering standard solution to the gas chromatograph for automated calibration. As a result of the evaluation the system was determined to be a reliable and accurate instrument. The AQUASCAN reported concentration values for methylene chloride, trichloroethylene, and toluene in the Pinellas ground water were within 20% of reference laboratory values

US Department of Energy interim mixed waste inventory report: Waste streams, treatment capacities and technologies: Volume 2, Site specific---California through Idaho

International Nuclear Information System (INIS)

1993-04-01

The Department of Energy (DOE) has prepared this report to provide an inventory of its mixed wastes and treatment capacities and technologies in response to Section 105(a) of the Federal Facility Compliance act (FFCAct) of 1992 (Pub. L. No. 102-386). As required by the FFCAct-1992, this report provide site-specific information on DOE's mixed waste streams and a general review of available and planned treatment facilities for mixed wastes for the following sites: eight California facilities which are Energy Technology engineering Center, General Atomics, General Electric Vallecitos Nuclear Center, Lawrence Berkeley Laboratory, Lawrence Livermore National Laboratory, Laboratory for Energy-Related Health Research, Mare Island Naval Shipyard, and Sandia national Laboratories; Grand Junction Project Office; Rocky Flats Plant; Knolls Atomic Power Laboratory-Windsor Site; Pinellas Plant; Pearl Harbor Naval Shipyard; Argonne National Laboratory-West; and Idaho National Engineering Laboratory

Hurricane Elena and Pinellas County, Florida: Some Lessons Learned from the Largest Evacuation of Nursing Home Patients in History.

Science.gov (United States)

Mangum, Wiley P.; And Others

1989-01-01

Studied prior planning for and problems associated with evacuation of 1,860 nursing home patients in Pinellas County, Florida, due to Hurricane Elena in 1985 through questionnaires administered to nursing home administrators and public documents. Found most serious problems to be transporting patients to shelters in timely fashion, delayed passage…

Treatment of Chlorinated Solvents in Groundwater Beneath an Occupied Building at the Young-Rainey STAR Center, Pinellas, FL

Energy Technology Data Exchange (ETDEWEB)

Daniel, Joe [Navarro Research and Engineering; Surovchak, Scott [Dept. of Energy (DOE), Legacy Management; Tabor, Charles [Navarro Research and Engineering

2016-03-01

Groundwater contamination, consisting of two dissolved-phase plumes originating from chlorinated solvent source areas, in the southeastern portion of the Young- Rainey Star Center (also known as the Pinellas County, Florida, Site) in Largo, Florida, has migrated beyond the property boundary, beneath the roadways, and beneath adjacent properties to the south and east. Groundwater contamination will persist as long as the onsite contaminant source remains. The origin of the contamination appears to be multiple long-term point sources beneath Building 100, a 4.5 ha (11 acre) building that housed manufacturing facilities during US DOE operations at the site. The site is now owned by Pinellas County, and most of the space inside the building is leased to private companies, so DOE chose not to conduct characterization or remediation through the floor of the building, instead choosing to conduct all work from outside the building. Injection of emulsified soybean oil and a microbial culture has been used at other areas of the site to accelerate naturally occurring bacterial processes that degrade groundwater contaminants to harmless compounds, and that same approach was chosen for this task. The technical approach consisted of installing horizontal wells from outside the building footprint, extending through and around the identified subsurface treatment areas, and terminating beneath the building. Two 107 m (350 ft) long wells, two 122 m (400 ft) long wells, and four 137 m (450 ft) long wells have been installed to intersect the inferred source areas and confirmed contaminant plumes beneath the building. DOE then injected emulsified vegetable oil and a microbial culture into the horizontal wells at each of several target areas beneath the building where the highest groundwater contaminant concentrations have been detected. The target areas are the northwest corner of the building between the old drum storage pad locations and monitoring well PIN12-S35B, the vicinity of

Radionuclide air emissions. Annual report for calendar year 1997

International Nuclear Information System (INIS)

1997-08-01

A description is provided of radioactive effluent releases from the Pinellas Plant. The DOE sold the Pinellas Plant in March 1995. A portion of the plant was backed by DOE until September 1997 to facilitate a safe transition to commercial ventures.The plant's radiological processing equipment was cleaned from past DOE operations. Emissions from the cleanup activity were monitored

Next Generation Nuclear Plant Project Evaluation of Siting a HTGR Co-generation Plant on an Operating Commercial Nuclear Power Plant Site

International Nuclear Information System (INIS)

Demick, L.E.

2011-01-01

This paper summarizes an evaluation by the Idaho National Laboratory (INL) Next Generation Nuclear Plant (NGNP) Project of siting a High Temperature Gas-cooled Reactor (HTGR) plant on an existing nuclear plant site that is located in an area of significant industrial activity. This is a co-generation application in which the HTGR Plant will be supplying steam and electricity to one or more of the nearby industrial plants.

Next Generation Nuclear Plant Project Evaluation of Siting a HTGR Co-generation Plant on an Operating Commercial Nuclear Power Plant Site

Energy Technology Data Exchange (ETDEWEB)

L.E. Demick

2011-10-01

This paper summarizes an evaluation by the Idaho National Laboratory (INL) Next Generation Nuclear Plant (NGNP) Project of siting a High Temperature Gas-cooled Reactor (HTGR) plant on an existing nuclear plant site that is located in an area of significant industrial activity. This is a co-generation application in which the HTGR Plant will be supplying steam and electricity to one or more of the nearby industrial plants.

Site survey for nuclear power plants

International Nuclear Information System (INIS)

1984-01-01

This Safety Guide describes the first stage of the siting process for nuclear power plants - the site survey to select one or more preferred candidate sites. Its purpose is to recommend procedures and provide information for use in implementing a part of the Code of Practice on Safety in Nuclear Power Plant Siting (IAEA Safety Series No.50-C-S). The organization, procedures, methodologies, guidance for documenting the site survey process and examples of detailed procedures on some safety-related site characteristics are given in the Guide

Environmental monitoring report, 1976

International Nuclear Information System (INIS)

1977-01-01

The effluent and environmental monitoring programs maintained by the Pinellas Plant are designed to determine the efficiencies of treatment and control mechanisms; to provide measurements of discharge concentrations for comparison with applicable standards; and to assess the concentrations of these discharges in the environment. Site perimeter and off-site air samples for tritium gas and tritium oxide, as well as off-site surface water samples obtained to distances of 9.6 kilometers (6 miles) from the plant site and analyzed for tritium content, showed levels significantly less than 1 / 10 of 1 percent of the recommended guide for continuous nonoccupational exposure. Small sealed plutonium sources are utilized at this site. No plutonium was released to the environment and monitoring data showed environmental background levels

Vascular Plants of the Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Sackschewsky, Michael R.; Downs, Janelle L.

2001-09-28

This report provides an updated listing of the vascular plants present on and near the U.S. Department of Energy Hanford Site. This document is an update of a listing of plants prepared by Sackschewdky et al. in 1992. Since that time there has been a significant increase in the botanical knowledge of the Hanford Site. The present listing is based on an examination of herbarium collections held at PNNL, at WSU-Tri Cities, WSU-Pullman, Bringham Young University, and The University of Washington, and on examination of ecological literature derived from the Hanford and Benton county areas over the last 100 years. Based on the most recent analysis, there are approximately 725 different plant species that have been documented on or around the Hanford Site. This represents an approximate 20% increase in the number of species reported within Sackschewsky et al. (1992). This listing directly supports DOE and contractor efforts to assess the potential impacts of Hanford Site operations on the biological environment, including impacts to rare habitats and to species listed as endangered or\\ threatened. This document includes a listing of plants currently listed as endangered, threatened, or otherwise of concern to the Washington Natural Heritage Program or the U.S. Fish and Wildlife Service, as well as those that are currently listed as noxious weeds by the State of Washington. Also provided is an overview of how plants on the Hanford Site can be used by people. This information may be useful in developing risk assessment models, and as supporting information for clean-up level and remediation decisions.

Vascular Plants of the Hanford Site

International Nuclear Information System (INIS)

Sackschewsky, Michael R.; Downs, Janelle L.

2001-01-01

This report provides an updated listing of the vascular plants present on and near the U.S. Department of Energy Hanford Site. This document is an update of a listing of plants prepared by Sackschewdky et al. in 1992. Since that time there has been a significant increase in the botanical knowledge of the Hanford Site. The present listing is based on an examination of herbarium collections held at PNNL, at WSU-Tri Cities, WSU-Pullman, Brigham Young University, and The University of Washington, and on examination of ecological literature derived from the Hanford and Benton county areas over the last 100 years. Based on the most recent analysis, there are approximately 725 different plant species that have been documented on or around the Hanford Site. This represents an approximate 20% increase in the number of species reported within Sackschewsky et al. (1992). This listing directly supports DOE and contractor efforts to assess the potential impacts of Hanford Site operations

Underground siting of nuclear power plants

International Nuclear Information System (INIS)

Pinto, S.; Telleschi, P.

1978-10-01

Two of the main underground siting alternatives, the rock cavity plant and the pit siting, have been investigated in detail and two layouts, developed for specific sites, have been proposed. The influence of this type of siting on normal operating conditions and during abnormal occurences have been investigated. (Auth.)

Nuclear power plant siting

International Nuclear Information System (INIS)

Sulkiewicz, M.; Navratil, J.

The construction of a nuclear power plant is conditioned on territorial requirements and is accompanied by the disturbance of the environment, land occupation, population migration, the emission of radioactive wastes, thermal pollution, etc. On the other hand, a nuclear power plant makes possible the introduction of district heating and increases the economic and civilization activity of the population. Due to the construction of a nuclear power plant the set limits of negative impacts must not be exceeded. The locality should be selected such as to reduce the unfavourable effects of the plant and to fully use its benefits. The decision on the siting of the nuclear power plant is preceded by the processing of a number of surveys and a wide range of documentation to which the given criteria are strictly applied. (B.H.)

Site and plant species are important determinants of the Methylobacterium community composition in the plant phyllosphere.

Science.gov (United States)

Knief, Claudia; Ramette, Alban; Frances, Lisa; Alonso-Blanco, Carlos; Vorholt, Julia A

2010-06-01

The plant phyllosphere constitutes a habitat for numerous microorganisms; among them are members of the genus Methylobacterium. Owing to the ubiquitous occurrence of methylobacteria on plant leaves, they represent a suitable target for studying plant colonization patterns. The influence of the factor site, host plant species, time and the presence of other phyllosphere bacteria on Methylobacterium community composition and population size were evaluated in this study. Leaf samples were collected from Arabidopsis thaliana or Medicago truncatula plants and from the surrounding plant species at several sites. The abundance of cultivable Methylobacterium clearly correlated with the abundance of other phyllosphere bacteria, suggesting that methylobacteria constitute a considerable and rather stable fraction of the phyllosphere microbiota under varying environmental conditions. Automated ribosomal intergenic spacer analysis (ARISA) was applied to characterize the Methylobacterium community composition and showed the presence of similar communities on A. thaliana plants at most sites in 2 consecutive years of sampling. A substantial part of the observed variation in the community composition was explained by site and plant species, especially in the case of the plants collected at the Arabidopsis sites (50%). The dominating ARISA peaks that were detected on A. thaliana plants were found on other plant species grown at the same site, whereas some different peaks were detected on A. thaliana plants from other sites. This indicates that site-specific factors had a stronger impact on the Methylobacterium community composition than did plant-specific factors and that the Methylobacterium-plant association is not highly host plant species specific.

Underground siting of nuclear power plants: potential benefits and penalties

International Nuclear Information System (INIS)

Allensworth, J.A.; Finger, J.T.; Milloy, J.A.; Murfin, W.B.; Rodeman, R.; Vandevender, S.G.

1977-08-01

The potential for improving nuclear power safety is analyzed by siting plants underground in mined cavities or by covering plants with fill earth after construction in an excavated cut. Potential benefits and penalties of underground plants are referenced to analogous plants located on the surface. Three representative regional sites having requisite underground geology were used to evaluate underground siting. The major factors which were evaluated for all three sites were: (1) containment of radioactive materials, (2) transport of groundwater contamination, and (3) seismic vulnerability. External protection, plant security, feasibility, operational considerations, and cost were evaluated on a generic basis. Additionally, the national availability of sites having the requisite geology for both underground siting concepts was determined

Nuclear power plant site evaluation using site population-meterology factor

International Nuclear Information System (INIS)

Rho, B.H.; Kang, C.H.

1982-01-01

In this paper, as a site evaluation technique, SPNF(Site Population Neteorology Factor) which is modified from SPF(Site Population Factor) of the USNRC model, is defined from site population and meteorology data in order to consider the radiological impacts to the population at large from the atmospheric dispersion of the radioactive effluents released during routine plant operation as well as accidental conditions. The SPMF model proved its propriety from the comparison of SPMF and SPF for Kori site. The relative suitability of Korean sites to the U.S. sites have been also examined using SPF. (Author)

Siting nuclear power plants

International Nuclear Information System (INIS)

Yellin, J.; Joskow, P.L.

1980-01-01

The first edition of this journal is devoted to the policies and problems of siting nuclear power plants and the question of how far commercial reactors should be placed from urban areas. The article is divided into four major siting issues: policies, risk evaluation, accident consequences, and economic and physical constraints. One concern is how to treat currently operating reactors and those under construction that were established under less-stringent criteria if siting is to be used as a way to limit the consequences of accidents. Mehanical cost-benefit analyses are not as appropriate as the systematic use of empirical observations in assessing the values involved. Stricter siting rules are justified because (1) opposition because of safety is growing: (2) remote siting will make the industry more stable; (3) the conflict is eliminated between regulatory policies and the probability basis for nuclear insurance; and (4) joint ownership of utilities and power-pooling are increasing. 227 references, 7 tables

Method for assigning sites to projected generic nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Holter, G.M.; Purcell, W.L.; Shutz, M.E.; Young, J.R.

1986-07-01

Pacific Northwest Laboratory developed a method for forecasting potential locations and startup sequences of nuclear power plants that will be required in the future but have not yet been specifically identified by electric utilities. Use of the method results in numerical ratings for potential nuclear power plant sites located in each of the 10 federal energy regions. The rating for each potential site is obtained from numerical factors assigned to each of 5 primary siting characteristics: (1) cooling water availability, (2) site land area, (3) power transmission land area, (4) proximity to metropolitan areas, and (5) utility plans for the site. The sequence of plant startups in each federal energy region is obtained by use of the numerical ratings and the forecasts of generic nuclear power plant startups obtained from the EIA Middle Case electricity forecast. Sites are assigned to generic plants in chronological order according to startup date.

Method for assigning sites to projected generic nuclear power plants

International Nuclear Information System (INIS)

Holter, G.M.; Purcell, W.L.; Shutz, M.E.; Young, J.R.

1986-07-01

Pacific Northwest Laboratory developed a method for forecasting potential locations and startup sequences of nuclear power plants that will be required in the future but have not yet been specifically identified by electric utilities. Use of the method results in numerical ratings for potential nuclear power plant sites located in each of the 10 federal energy regions. The rating for each potential site is obtained from numerical factors assigned to each of 5 primary siting characteristics: (1) cooling water availability, (2) site land area, (3) power transmission land area, (4) proximity to metropolitan areas, and (5) utility plans for the site. The sequence of plant startups in each federal energy region is obtained by use of the numerical ratings and the forecasts of generic nuclear power plant startups obtained from the EIA Middle Case electricity forecast. Sites are assigned to generic plants in chronological order according to startup date

Nuclear Power Plant project site selection geotechnical considerations

International Nuclear Information System (INIS)

Katti, V.J.; Banerjee, D.C.

1997-01-01

During the selection of a site for Nuclear Power Plant (NPP) and Radioactive Waste Plant (RWP), geotechnical investigations play a significant role in deciding merits and demerits of the sites. Any accidents in these units can play havoc on mankind and may leave bitter imprints on generations to come. Hence proper care has to be taken at the early stage for selecting the sites. Site selection procedure is a complicated one, because it involves experts from various disciplines like geology, geophysics, civil, mechanical electrical engineering, health-physics and other fields

Site-Specific Seismic Site Response Model for the Waste Treatment Plant, Hanford, Washington

Energy Technology Data Exchange (ETDEWEB)

Rohay, Alan C.; Reidel, Steve P.

2005-02-24

This interim report documents the collection of site-specific geologic and geophysical data characterizing the Waste Treatment Plant site and the modeling of the site-specific structure response to earthquake ground motions.

Secondary plant succession on disturbed sites at Yucca Mountain, Nevada

Energy Technology Data Exchange (ETDEWEB)

Angerer, J.P.; Ostler, W.K.; Gabbert, W.D.; Schultz, B.W.

1994-12-01

This report presents the results of a study of secondary plant succession on disturbed sites created during initial site investigations in the late 1970s and early 1980s at Yucca Mountain, NV. Specific study objectives were to determine the rate and success of secondary plant succession, identify plant species found in disturbances that may be suitable for site-specific reclamation, and to identify environmental variables that influence succession on disturbed sites. During 1991 and 1992, fifty seven disturbed sites were located. Vegetation parameters, disturbance characteristics and environmental variables were measured at each site. Disturbed site vegetation parameters were compared to that of undisturbed sites to determine the status of disturbed site plant succession. Vegetation on disturbed sites, after an average of ten years, was different from undisturbed areas. Ambrosia dumosa, Chrysothamnus teretifolius, Hymenoclea salsola, Gutierrezia sarothrae, Atriplex confertifolia, Atriplex canescens, and Stephanomeria pauciflora were the most dominant species across all disturbed sites. With the exception of A. dumosa, these species were generally minor components of the undisturbed vegetation. Elevation, soil compaction, soil potassium, and amounts of sand and gravel in the soil were found to be significant environmental variables influencing the species composition and abundance of perennial plants on disturbed sites. The recovery rate for disturbed site secondary succession was estimated. Using a linear function (which would represent optimal conditions), the recovery rate for perennial plant cover, regardless of which species comprised the cover, was estimated to be 20 years. However, when a logarithmic function (which would represent probable conditions) was used, the recovery rate was estimated to be 845 years. Recommendations for future studies and site-specific reclamation of disturbances are presented.

Secondary plant succession on disturbed sites at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Angerer, J.P.; Ostler, W.K.; Gabbert, W.D.; Schultz, B.W.

1994-12-01

This report presents the results of a study of secondary plant succession on disturbed sites created during initial site investigations in the late 1970s and early 1980s at Yucca Mountain, NV. Specific study objectives were to determine the rate and success of secondary plant succession, identify plant species found in disturbances that may be suitable for site-specific reclamation, and to identify environmental variables that influence succession on disturbed sites. During 1991 and 1992, fifty seven disturbed sites were located. Vegetation parameters, disturbance characteristics and environmental variables were measured at each site. Disturbed site vegetation parameters were compared to that of undisturbed sites to determine the status of disturbed site plant succession. Vegetation on disturbed sites, after an average of ten years, was different from undisturbed areas. Ambrosia dumosa, Chrysothamnus teretifolius, Hymenoclea salsola, Gutierrezia sarothrae, Atriplex confertifolia, Atriplex canescens, and Stephanomeria pauciflora were the most dominant species across all disturbed sites. With the exception of A. dumosa, these species were generally minor components of the undisturbed vegetation. Elevation, soil compaction, soil potassium, and amounts of sand and gravel in the soil were found to be significant environmental variables influencing the species composition and abundance of perennial plants on disturbed sites. The recovery rate for disturbed site secondary succession was estimated. Using a linear function (which would represent optimal conditions), the recovery rate for perennial plant cover, regardless of which species comprised the cover, was estimated to be 20 years. However, when a logarithmic function (which would represent probable conditions) was used, the recovery rate was estimated to be 845 years. Recommendations for future studies and site-specific reclamation of disturbances are presented

Early Site Permit Demonstration Program: Plant parameters envelope report

International Nuclear Information System (INIS)

1993-03-01

The Early Site Permit (ESP) Demonstration Program is the nuclear industry's initiative for piloting the early resolution of siting-related issues before the detailed design proceedings of the combined operating license review. The ESP Demonstration Program consists of three phases. The plant parameters envelopes task is part of Phase 1, which addresses the generic review of applicable federal regulations and develops criteria for safety and environmental assessment of potential sites. The plant parameters envelopes identify parameters that characterize the interface between an ALWR design and a potential site, and quantify the interface through values selected from the Utility Requirements Documents, vendor design information, or engineering assessments. When augmented with site-specific information, the plant parameters envelopes provide sufficient information to allow ESPs to be granted based on individual ALWR design information or enveloping design information for the evolutionary, passive, or generic ALWR plants. This document is expected to become a living document when used by future applicants

ITER plant layout and site services

International Nuclear Information System (INIS)

Chuyanov, V.A.

2000-01-01

The ITER site has not yet been determined. Nevertheless, to develop a construction plan and a cost estimate, it is necessary to have a detailed layout of the buildings, structures and outdoor equipment integrated with the balance of plant service systems prototypical of large fusion power plants. These services include electrical power for magnet feeds and plasma heating systems, cryogenic and conventional cooling systems, compressed air, gas supplies, demineralized water, steam and drainage. Nuclear grade facilities are provided to handle tritium fuel and activated waste, as well as to prevent radiation exposure of workers and the public. To prevent interference between services of different types and for efficient arrangement of buildings, structures and equipment within the site area, a plan was developed which segregated different classes of services to four quadrants surrounding the tokamak building, placed at the approximate geographical centre of the site. The locations of the buildings on the generic site were selected to meet all design requirements at minimum total project cost. A similar approach was used to determine the locations of services above, at and below grade. The generic site plan can be adapted to the site selected for ITER without significant changes to the buildings or equipment. Some rearrangements may be required by site topography, resulting primarily in changes to the length of services that link the buildings and equipment. (author)

Mixed-waste minimization activities in the nuclear weapons complex

International Nuclear Information System (INIS)

Marchetti, J.A.; Suffern, J.S.

1991-01-01

Over the past 40 years, the US Department of Energy (DOE) and the nuclear weapons complex have successfully executed their mission of providing the country with a strong nuclear deterrent. Now, however, they must attain another mission at the same time: to eliminate or greatly reduce the environmental, safety, and health problems in the complex. Mixed-waste minimization activities have taken place in 11 of the complex production plants and laboratories: the Pinellas plant, the Mount plant, the Kansas City plant, the Y-12 plant, the Rocky Flats plant, the Savannah River Site (SRS), the Savannah River Site (SRS), the Pantex plant, the Nevada Test Site, Sandia National Laboratories, Los Alamos National Laboratory, and the Lawrence Livermore National Laboratory. The mixed-waste minimization opportunities that have been implemented to date by the production facilities are different from those that have been implemented by the laboratories. Areas of opportunity at the plants involve the following activities: (1) process design or improvement; (2) substitution of materials; (3) waste segregation; (4) recycling; and (5) administrative controls

On-site tests on the nuclear power plants

International Nuclear Information System (INIS)

Morilhat, P.; Favennec, J.M.; Neau, P.; Preudhomme, E.

1996-01-01

On-site tests and experiments are performed by EDF Research and Development Division on the nuclear power plants to assess the behaviour of major components submitted to thermal and vibratory solicitations. On-going studies deal with the qualification of new nuclear power plant standard and with the feedback of plants under operation. The tests, particularly the investigation tests, correspond to large investments and entail an important data volume which must ensure the continuity over a long period of the order of magnitude of the in-service plant life (around 40 years). This paper addresses the on-site experimental activities, describes the means to be used, and gives an example: the qualification of SG of new 1450 MW nuclear power plants. (author)

Environmental monitoring report, 1975

International Nuclear Information System (INIS)

1976-01-01

The Pinellas Plant is operated for the U. S. Energy Research and Development Administration (ERDA) by the Neutron Devices Department of the General Electric Company. The plant's 1100 employees are engaged in the design, development, and manufacture of special electronic and mechanical nuclear weapons components. The effluent and environmental monitoring programs maintained by the Pinellas Plant are designed to determine the efficiencies of treatment and control mechanisms, to provide measurements of discharge concentrations for comparison with applicable standards, and to assess the effect of these discharges on the environment. Small quantities of tritium gas, tritium oxide, and krypton-85 gas were released from the plant during the year. Average ground level concentrations of these radioisotopes were all significantly less than 1/10 of 1 percent of the recommended guide for continuous nonoccupational exposure

Seismic PSA method for multiple nuclear power plants in a site

Energy Technology Data Exchange (ETDEWEB)

Hakata, Tadakuni [Nuclear Safety Commission, Tokyo (Japan)

2007-07-15

The maximum number of nuclear power plants in a site is eight and about 50% of power plants are built in sites with three or more plants in the world. Such nuclear sites have potential risks of simultaneous multiple plant damages especially at external events. Seismic probabilistic safety assessment method (Level-1 PSA) for multi-unit sites with up to 9 units has been developed. The models include Fault-tree linked Monte Carlo computation, taking into consideration multivariate correlations of components and systems from partial to complete, inside and across units. The models were programmed as a computer program CORAL reef. Sample analysis and sensitivity studies were performed to verify the models and algorithms and to understand some of risk insights and risk metrics, such as site core damage frequency (CDF per site-year) for multiple reactor plants. This study will contribute to realistic state of art seismic PSA, taking consideration of multiple reactor power plants, and to enhancement of seismic safety. (author)

Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Portsmouth Gaseous Diffusion Plant site

International Nuclear Information System (INIS)

Marmer, G.J.; Dunn, C.P.; Filley, T.H.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Cleland, J.H.

1991-09-01

Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. In the 1970s, the US Department of Energy (DOE) began investigating more efficient and cost-effective enrichment technologies. In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser isotope Separation (U-AVLIS) technology with the near-term goal to provide the necessary information to make a deployment decision by November 1992. Initial facility operation is anticipated for 1999. A programmatic document for use in screening DOE sites to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. The final evaluation, which included sensitivity studies, identified the Oak Ridge Gaseous Diffusion Plant (ORGDP) site, the Paducah Gaseous Diffusion Plant (PGDP) site, and the Portsmouth Gaseous Diffusion Plant (PORTS) site as having significant advantages over the other sites considered. This environmental site description (ESD) provides a detailed description of the PORTS site and vicinity suitable for use in an environmental impact statement (EIS). This report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during site visits. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use. Socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3

Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Portsmouth Gaseous Diffusion Plant site

Energy Technology Data Exchange (ETDEWEB)

Marmer, G.J.; Dunn, C.P.; Filley, T.H.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Cleland, J.H.

1991-09-01

Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. In the 1970s, the US Department of Energy (DOE) began investigating more efficient and cost-effective enrichment technologies. In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser isotope Separation (U-AVLIS) technology with the near-term goal to provide the necessary information to make a deployment decision by November 1992. Initial facility operation is anticipated for 1999. A programmatic document for use in screening DOE sites to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. The final evaluation, which included sensitivity studies, identified the Oak Ridge Gaseous Diffusion Plant (ORGDP) site, the Paducah Gaseous Diffusion Plant (PGDP) site, and the Portsmouth Gaseous Diffusion Plant (PORTS) site as having significant advantages over the other sites considered. This environmental site description (ESD) provides a detailed description of the PORTS site and vicinity suitable for use in an environmental impact statement (EIS). This report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during site visits. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use. Socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3.

Underground siting of nuclear power plants

International Nuclear Information System (INIS)

Bender, F.

1982-01-01

The symposium gave the opportunity for an international exchange of views on the concepts of underground nuclear power plants, which are presently world wide under consideration. The results of investigations into the advantages and disadvantages with regard to the technical safety aspects of the underground plants in comparison to plants on the surface led to open and sometimes controversal discussions. As a result of the symposium (32 contributions) a general agreement can be stated on the judgement concerning the advantages and the disadvantages of underground nuclear power plants (nnp). The advantages are: increased protection against external events; delayed release of fission products in accident situations, if the closures operate properly. The disadvantages are: increased costs of the construction of underground and restrictions to such sites where either large caverns or deep pits can be constructed, which also requires that certain technical problems must be solved beforehand. Also, additional safety certificates related to the site will be required within the licensing procedures. The importance of these advantages and disadvantages was in some cases assessed very differently. The discussions also showed, that there are a number of topics where some questions have not been finally answered yet. (orig./HP) [de

In-situ solidification cleans up old gas plant site

International Nuclear Information System (INIS)

Hatfield, A.D.; Dennis, N.D.

1995-01-01

A manufactured gas plant site in Columbus, Georgia, was the location of an environmental cleanup in 1992. Manufactured gas was produced at this site from 1854 to 1931 with the availability of natural gas from a transmission pipeline causing its demise. However, waste products, primarily coal tar from the earlier years of plant operation, remained with the site. In-situ solidification was chosen as the cleanup method. Post monitoring activities show that the project was successful and the site is now a park and a leading part of river front development

Rock siting of nuclear power plants from a reactor safety standpoint

International Nuclear Information System (INIS)

1975-11-01

The study has aimed at surveying the advantages and disadvantages of a rock sited nuclear power plant from a reactor safety standpoint. The studies performed are almost entirely concentrated on the BWR alternative. The design of a nuclear power plant in rock judged most appropriate has been studied in greater detail, and a relatively extensive safety analysis has been made. It is found that the presented technical design of the rock sited alternative is sufficiently advanced to form a basis for further projecting treatment. The chosen technical design of the reactor plant demands a cavern with a 45-50 metre span. Caverns without strengthening efforts with such spans are used in mines, but have no previously been used for industrial plants. Studies of the stability of such caverns show that a safety level is attainable corresponding to the safety required for the other parts of the nuclear power plant. The conditions are that the rock is of high quality, that necessary strengthening measures are taken and that careful studies of the rock are made before and during the blasting, and also during operation of the plant. When locating a rock sited nuclear power plant, the same criteria must be considered as for an above ground plant, with additional stronger demands for rock quality. The presented rock sited nuclear power plant has been assessed to cost 20 % more in total construction costs than a corresponding above ground plant. The motivations for rock siting also depend on whether a condensing plant for only electricity production, or a plant for combined power production and district heating, is considered. The latter would under certain circumstances make rock siting look more attractive. (author)

A method of risk assessment for a multi-plant site

International Nuclear Information System (INIS)

White, R.F.

1983-06-01

A model is presented which can be used in conjunction with probabilistic risk assessment to estimate whether a site on which there are several plants (reactors or chemical plants containing radioactive materials) meets whatever risk acceptance criteria or numerical risk guidelines are applied at the time of the assessment in relation to various groups of people and for various sources of risk. The application of the multi-plant site model to the direct and inverse methods of risk assessment is described. A method is proposed by which the potential hazard rating associated with a given plant can be quantified so that an appropriate allocation can be made when assessing the risks associated with each of the plants on a site. (author)

Part 2: Conserving and Planting Trees at Development Sites

Science.gov (United States)

Karen Cappiella; Tom Schueler; Tiffany Wright

2006-01-01

This manual presents specific ways to enable developers, engineers or landscape architects to incorporate more trees into a development site. The proposed approach focuses on protecting existing trees, planting trees in storm water treatment practices, and planting trees in other open spaces at the development site. This manual introduces conceptual designs for storm...

Review of underground siting of nuclear power plants

International Nuclear Information System (INIS)

1974-01-01

A review of the potential for the underground siting of nuclear power generating plants has been undertaken. The review comprised a survey and assessment of relevant published documents currently available, together with discussions with Government sponsored agencies and other bodies, to evaluate the current status of technology related to the design and construction of underground nuclear power plants. It includes a review of previous work related to the underground siting of power plants and other facilities; a preliminary evaluation of the relative merits of the various concepts of undergrounding which have been proposed or constructed; a review of current technology as it relates to the requirements for the design, construction and operation of underground nuclear power plants; an examination of the safety and environmental aspects; and the identification of areas of further study which will be required if the underground is to be established as a fully viable alternative to surface siting. No attempt has been made to draw final conclusions at this stage. Nothing has been found to suggest that the underground siting concept could not provide a viable alternative to the surface concept. It is also apparent that no major technological developments are required. It is not clear, however, whether the improvements in safety and containment postulated for the underground can be realized at an economic cost; or even whether any additional cost is in fact involved. The problem is essentially site dependent and requires further study for which recommendations are made. (auth)

Geological and geotechnical investigations for nuclear power plants sites

International Nuclear Information System (INIS)

Alves, P.R.R.

1984-09-01

This dissertation presents a general methodology for the tasks of geological and geotechnical investigations, to be performed in the proposed sites for construction of nuclear Power Plants. In this work, items dealing with the standards applied to licensing of Nuclear Power Plants, with the selection process of sites and identification of geological and geotechnical parameters needed for the regional and local characterization of the area being studied, were incorporated. This dissertation also provides an aid to the writing of Technical Reports, which are part of the documentation an owner of a Nuclear Power Plant needs to submit to the Comissao Nacional de Energia Nuclear, to fulfill the nuclear installation licensing requirements. Moreover, this work can contribute to the planning of field and laboratory studies, needed to determine the parameters of the area under investigation, for the siting of Nuclear Power Plants. (Author) [pt

Regional approaches to power plant siting in the United States of America

International Nuclear Information System (INIS)

DiNunno, J.J.

1975-01-01

The selection and evaluation of sites for power plants in the United States of America have become increasingly difficult in recent years as pressures from various societal segments have resulted in governmental restraints on selection and burning of fossil fuels, methods of heat dissipation, acquisition of transmission rights of way, and on environmental impact of industrialization in general. New legislation at both Federal and state levels has been enacted that influences power plant siting. In addition to environmental requirements that must be satisfied, implementing procedures require documented justification for sites chosen and public disclosure of the basis for selection. Some states have consolidated their regulatory activities in the power plant siting area to provide for a more unified approach to these problems. Although nuclear plants have by far the most rigorous requirements for documentation of site selection and plant design, the application of the same general philosophies to fossil plants has been made in several states and can be anticipated elsewhere. Individual site-related investigations have not so much changed in basics as they have been enlarged in scope. Whereas in the past the search for siting alternatives was frequently confined to a utility's service area, the additional siting constraints represented in environmental laws, the economies of size of nuclear power plants, and the sharing of plant capacities among utilities have contributed to a widening of the search area. Several states have assumed the responsibility for site search and investigation and their efforts extend state-wide. This paper discusses applications of regional approaches to power plant siting in the United States of America using case studies made by NUS Corporation, an engineering/environmental consulting firm. The universality of these approaches is indicated, leaving to national policies and goals the importance of values assigned to the basic siting factors

Regional siting survey for thermal power plants in the state of Ohio

International Nuclear Information System (INIS)

Elkins, M.L.; DiNunno, J.J.

1975-01-01

The selection and evaluation of sites for power plants have become increasingly difficult in recent years as pressures from various societal segments have resulted in government restraints on selection and burning of fossil fuels, on methods of heat dissipation, on acquisition of transmission line rights-of-way, and on environmental impact in general. The key elements in successful application of power plant siting technology are the development of the proper balance among the basic siting considerations and the understanding that level of detail in a study varies in an inverse relationship with the siting area under examination. As the first step in the process of selection and eventual licensing of new thermal power plant sites for a utility in the State of Ohio, the entire state was screened to determine promising candidate regions large enough to offer several possible candidate sites for thermal power plants. Because of the size of the area under consideration and the advantages of developing sites with an ultimate capacity for more than one power plant, sites with an installed capacity of 1100 to 4400 MW(e) were considered for this study. As a result of the preliminary screening conducted in four distinct steps, three candidate regions showed the best overall promise for either nuclear or fossil-fueled power plant development. Tentative identification was made of candidate sites within these candidate regions, and follow-on studies conducted in an increasing level of detail are presently in progress to determine the candidate site(s) most promising for power plant siting. (U.S.)

Safety in nuclear power plant siting. A code of practice

International Nuclear Information System (INIS)

1978-01-01

This publication is brought out within the framework of establishing Codes of Practice and Safety Guides for nuclear power plants: NUSS programme. The scope of the document encompasses site and site-plant interaction factors related to operational states and accident conditions. The purpose of the Code is to give criteria and procedures to be applied as appropriate to operational states and accident conditions, including those which could lead to emergency situations. This Code is mainly concerned with severe events of low probability which relate to the siting of nuclear power plants and have to be considered in designing a particular nuclear power plant. Annex: Examples of natural and man-made events relevant for design basis evaluation

Summary of wind data from nuclear power plant sites. [USA

Energy Technology Data Exchange (ETDEWEB)

Verholek, M. G.

1977-03-01

A summary of wind data from nuclear power plant sites is presented. National Weather Service archives are an immediately obvious source of wind data, but additional data sources are also available. Utility companies proposing to build nuclear power plants are required to establish on-site meteorological monitoring programs that include towers for collecting wind and temperature data for use in environmental impact assessments. These data are available for more than one hundred planned or operating nuclear power plant sites. A list of the sites, by state, is provided in Appendix A, while Appendix B contains an alphabetical list of the sites. This site wind data provides a valuable addition to the existing NWS data sets, and significantly enlarges the multilevel data presently available. The wind data published through the NRC is assembled and assessed here in order to provide a supplement to existing data sets.

Siting of light-water reactor power plants in the Federal Republic of Germany

International Nuclear Information System (INIS)

Kohler, H.A.G.

1975-01-01

The nuclear power plant site requirements formulated for environment protection in Germany allow nuclear power plants to be built at any site provided these requirements are duly taken into account in preparing and monitoring the site and in the design of the proposed power plant. After a brief discussion of light water reactor power plant sites, prevailing practice in site planning, site selection criteria, licensing procedure and used criteria, rules and guidelines, this paper reports on some considerations taken into account by the expert advisers and by the licensing authorities and future site planning. (orig.) [de

Rocky Flats Plant Site Environmental Report for 1992

Energy Technology Data Exchange (ETDEWEB)

Cirrincione, D.A.; Erdmann, N.L. [eds.

1992-12-31

The Rocky Rats Plant Site Environmental Report provides summary information on the plant`s environmental monitoring programs and the results recorded during 1992. The report contains a compliance summary, results of environmental monitoring and other related programs, a review of environmental remediation activities, information on external gamma radiation dose monitoring, and radiation dose estimates for the surrounding population.

Siting studies for new nuclear power plants in Argentina

International Nuclear Information System (INIS)

Barbaran, Gustavo A.

2008-01-01

This paper is a summary of the thesis prepared by the Group of Prospective and Energy Planning of the National Atomic Energy Commission for the 'Specialization on Applications of Nuclear Technology Course' of the Instituto Balseiro in 2007. It describes the evolution of siting studies through time and the main focus worldwide in this type of studies. Then, it makes a brief review of previous siting studies of nuclear power plants conducted in Argentina. It carries out a description of the methodology to conduct a site evaluation for nuclear power plants according to actual international criteria. Finally, it describes the licensing process that follows every site study. (author) [es

Managing Siting Activities for Nuclear Power Plants

International Nuclear Information System (INIS)

2012-01-01

One of the IAEA's statutory objectives is to ''seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world''. One way this objective is achieved is through the publication of a range of technical series. Two of these are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III.A.6 of the IAEA Statute, the safety standards establish 'standards of safety for protection of health and minimization of danger to life and property.' The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are written primarily in a regulatory style, and are binding on the IAEA for its own programmes. The principal users are the regulatory bodies in Member States and other national authorities. The IAEA Nuclear Energy Series comprises reports designed to encourage and assist R and D on, and application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia, and government officials, among others. This information is presented in guides, reports on technology status and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The IAEA Nuclear Energy Series complements the IAEA Safety Standards Series. The introduction of nuclear power brings new challenges to States - one of them being the selection of appropriates sites. It is a project that needs to begin early, be well managed, and deploy good communications with all stakeholders; including regulators. This is important, not just for those States introducing nuclear power for the first time, but for any State looking to build a new nuclear power plant. The purpose of the siting activities goes beyond choosing a suitable site and acquiring a licence. A large part of the project is about producing and maintaining a validated

Managing Siting Activities for Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-06-15

One of the IAEA's statutory objectives is to ''seek to accelerate and enlarge the contribution of atomic energy to peace, health and prosperity throughout the world''. One way this objective is achieved is through the publication of a range of technical series. Two of these are the IAEA Nuclear Energy Series and the IAEA Safety Standards Series. According to Article III.A.6 of the IAEA Statute, the safety standards establish 'standards of safety for protection of health and minimization of danger to life and property.' The safety standards include the Safety Fundamentals, Safety Requirements and Safety Guides. These standards are written primarily in a regulatory style, and are binding on the IAEA for its own programmes. The principal users are the regulatory bodies in Member States and other national authorities. The IAEA Nuclear Energy Series comprises reports designed to encourage and assist R and D on, and application of, nuclear energy for peaceful uses. This includes practical examples to be used by owners and operators of utilities in Member States, implementing organizations, academia, and government officials, among others. This information is presented in guides, reports on technology status and advances, and best practices for peaceful uses of nuclear energy based on inputs from international experts. The IAEA Nuclear Energy Series complements the IAEA Safety Standards Series. The introduction of nuclear power brings new challenges to States - one of them being the selection of appropriates sites. It is a project that needs to begin early, be well managed, and deploy good communications with all stakeholders; including regulators. This is important, not just for those States introducing nuclear power for the first time, but for any State looking to build a new nuclear power plant. The purpose of the siting activities goes beyond choosing a suitable site and acquiring a licence. A large part of the project is about producing and maintaining a validated

Early Site Permit Demonstration Program: Plant parameters envelope report. Volume 1

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

The Early Site Permit (ESP) Demonstration Program is the nuclear industry`s initiative for piloting the early resolution of siting-related issues before the detailed design proceedings of the combined operating license review. The ESP Demonstration Program consists of three phases. The plant parameters envelopes task is part of Phase 1, which addresses the generic review of applicable federal regulations and develops criteria for safety and environmental assessment of potential sites. The plant parameters envelopes identify parameters that characterize the interface between an ALWR design and a potential site, and quantify the interface through values selected from the Utility Requirements Documents, vendor design information, or engineering assessments. When augmented with site-specific information, the plant parameters envelopes provide sufficient information to allow ESPs to be granted based on individual ALWR design information or enveloping design information for the evolutionary, passive, or generic ALWR plants. This document is expected to become a living document when used by future applicants.

Alternative off-site power supply improves nuclear power plant safety

International Nuclear Information System (INIS)

Gjorgiev, Blaže; Volkanovski, Andrija; Kančev, Duško; Čepin, Marko

2014-01-01

Highlights: • Additional power supply for mitigation of the station blackout event in NPP is used. • A hydro power plant is considered as an off-site alternative power supply. • An upgrade of the probabilistic safety assessment from its traditional use is made. • The obtained results show improvement of nuclear power plant safety. - Abstract: A reliable power system is important for safe operation of the nuclear power plants. The station blackout event is of great importance for nuclear power plant safety. This event is caused by the loss of all alternating current power supply to the safety and non-safety buses of the nuclear power plant. In this study an independent electrical connection between a pumped-storage hydro power plant and a nuclear power plant is assumed as a standpoint for safety and reliability analysis. The pumped-storage hydro power plant is considered as an alternative power supply. The connection with conventional accumulation type of hydro power plant is analysed in addition. The objective of this paper is to investigate the improvement of nuclear power plant safety resulting from the consideration of the alternative power supplies. The safety of the nuclear power plant is analysed through the core damage frequency, a risk measure assess by the probabilistic safety assessment. The presented method upgrades the probabilistic safety assessment from its common traditional use in sense that it considers non-plant sited systems. The obtained results show significant decrease of the core damage frequency, indicating improvement of nuclear safety if hydro power plant is introduced as an alternative off-site power source

The problem of nuclear power plants site survey and selection

International Nuclear Information System (INIS)

Anh, T.H.; Hung, H.V.; Bui Quoc Thang

1986-01-01

The article presents the main steps of nuclear power plants siting, including the requirements from a nuclear power station onto the site, and the analysis of potential effects of a nuclear power station to the environment. Attentions are called upon the analysis of important factors such as electric transmission losses, cooling water supply, site accessibility, local infrastructure, risks due to man made and natural sources of aggression to the nuclear power plants, population, distribution, hydrological and atmospheric dispersion conditions

Nuclear power plant siting: Hydrogeologic aspects

International Nuclear Information System (INIS)

1984-01-01

This Safety Guide gives guidelines and methods for determining the ground water concentration of radionuclides that could result from postulated releases from nuclear power plants. The Guide gives recommendations on the data to be collected and the investigations to be performed at various stages of nuclear power plant siting in relation to the various aspects of the movement of accidentally released radioactive material through the ground water, the selection of an appropriate mathematical or physical model for the hydrodynamic dispersion even two-phase distribution of the radioactive material and an appropriate monitoring programme

Assessment parameters for coal-fired generation plant site selection

OpenAIRE

Abbas, Ahmad Rosly; Low, K. S.; Ahmad, Ir. Mohd Noh; Chan, J. H.; Sasekumar, A.; Abdul Ghaffar, Fauza; Osman Salleh, Khairulmaini; Raj, John K.; Abdul Yamin, Saad; Wan Aida, Wan Zahari; Phua, Y. T.; Phua, Y. N.; Wong, Y. Y.; Jamaludin, Ir. Mashitah; Jaafar, Shaari

2005-01-01

In order to meet future demand for electricity, Tenaga Nasional Berhad (TNB) is committedto the long-term strategic planning in locating suitable sites for future development of power stations.Site selection is an important process in the early planning stage of any power plant development asit will have significant implications on the capital investment, operational as well as the environmentand socio-economic costs of the power plant.The aim of this presentation is to briefly describe the t...

Geomorphologic specificities of selected sites for nuclear power plants in Czechoslovakia

International Nuclear Information System (INIS)

Kalvoda, J.; Demek, J.

1991-01-01

The contribution of geomorphology to the complex evaluation of properties of sites for the construction and operation of nuclear facilities is demonstrated. The unique manifestation of the present geodynamics at the Jaslovske Bohunice nuclear power plant locality and the spatial correlations of annals of the specific morphotectonic development of georeliefs of that nuclear power plant with the location of the epicentral earthquake zones are shown. The results of the geomorphological survey in the surroundings of the Temelin nuclear power plant construction site are described and a drawing is reproduced showing how the georelief of this locality divides into areas with different categories of occurrence of morpho-structural formations. For the Tetov locality, where the construction of a nuclear power plant is planned, the changes in the course of the Labe (Elbe) river which occurred in the Pleistocene are of importance in the assessment of the intensity of geodynamic processes. The geomorphological and geotectonic complexity of the planned Blahutovice nuclear power plant construction site is demonstrated. A drawing shows the morphotectonic situation in the surroundings of that construction site. (Z.S.). 4 figs

1000kW on-site PAFC power plant development and demonstration

Energy Technology Data Exchange (ETDEWEB)

Satomi, Tomohide; Koike, Shunichi [Phosphoric Acid Fuel Cell Technology Research Association (PAFC-TRA), Osaka (Japan); Ishikawa, Ryou [New Energy and Industrial Technology Development Organization (NEDO), Tokyo (Japan)

1996-12-31

Phosphoric Acid Fuel Cell Technology Research Association (PAFC-TRA) and New Energy and Industrial Technology Development Organization (NEDO) have been conducting a joint project on development of a 5000kW urban energy center type PAFC power plant (pressurized) and a 1000kW on-site PAFC power plant (non-pressurized). The objective of the technical development of 1000kW on-site PAFC power plant is to realize a medium size power plant with an overall efficiency of over 70% and an electrical efficiency of over 36%, that could be installed in a large building as a cogeneration system. The components and system integration development work and the plant design were performed in 1991 and 1992. Manufacturing of the plant and installation at the test site were completed in 1994. PAC test was carried out in 1994, and generation test was started in January 1995. Demonstration test is scheduled for 1995 and 1996.

A survey of the underground siting of nuclear power plants

International Nuclear Information System (INIS)

Pinto, S.

1979-12-01

The idea of locating nuclear power plants underground is not new, since in the period of time between the late fifties and the early sixties, four small nuclear plants have been built in Europe in rock cavities. Safety has been, in general, the main motivation for such a siting solution. In the last years several factors such as increasing power transmission costs, decreasing number of suitable sites above ground, increased difficulties in obtaining site approval by the licensing authorities, increasing opposition to nuclear power, increasing concern for extreme - but highly improbable - accidents, together with the possibility of utilizing the waste heat and the urban siting concept have renewed the interest for the underground siting as an alternative to surface siting. The author presents a survey of the main studies carried out on the subject of underground siting. (Auth.)

Case study of siting technology for underground nuclear power plant

International Nuclear Information System (INIS)

Hibino, Satoshi; Komada, Hiroya; Honsho, Shizumitsu; Fujiwara, Yoshikazu; Motojima, Mutsumi; Nakagawa, Kameichiro; Nosaki, Takashi

1991-01-01

Underground siting method is one of new feasible siting methods for nuclear power plants. This report presents the results on case studies on underground siting. Two sites of a steeply inclined and plateau like configurations were selected. 'Tunnel type cavern; all underground siting' method was applied for the steeply inclined configuration, and 'shaft type semi-cavern; partial underground siting' method was applied for the plateau like configuration. The following designs were carried out for these two sites as case studies; (1) conceptual designs, (2) geological surveys and rock mechanics tests, (3) stability analysis during cavern excavations, (4) seismic stability analysis of caverns during earthquake, (5) reinforcement designs for caverns, (6) drainage designs. The case studies showed that these two cases were fully feasible, and comparison between two cases revealed that the 'shaft type semi-cavern; partial underground siting' method was more suitable for Japanese islands. As a first step of underground siting, therefore, the authors recommend to construct a nuclear power plant by this method. (author)

Code on the safety of nuclear power plants: Siting

International Nuclear Information System (INIS)

1988-01-01

This Code provides criteria and procedures that are recommended for safety in nuclear power plant siting. It forms part of the Agency's programme for establishing Codes and Safety Guides relating to land based stationary thermal neutron power plants

Quality assurance in siting of Nuclear Power Plants

International Nuclear Information System (INIS)

2005-03-01

This guide describes the requirements of quality assurance programme (QAP) that need to be implemented at the siting stage, by the organisation having overall responsibility for the nuclear power plant. The scope of the guide covers the quality assurance aspects related to management, performance and assessment activities during siting stage of NPPs

Rocky Flats Plant Site Environmental Report for 1992

International Nuclear Information System (INIS)

Cirrincione, D.A.; Erdmann, N.L.

1992-01-01

The Rocky Rats Plant Site Environmental Report provides summary information on the plant's environmental monitoring programs and the results recorded during 1992. The report contains a compliance summary, results of environmental monitoring and other related programs, a review of environmental remediation activities, information on external gamma radiation dose monitoring, and radiation dose estimates for the surrounding population

Remote sensing for nuclear power plant siting

International Nuclear Information System (INIS)

Siegal, B.S.; Welby, C.W.

1981-01-01

It is shown that satellite remote sensing provides timely and cost-effective information for siting and site evaluation of nuclear power plants. Side-looking airborne radar (SLAR) imagery is especially valuable in regions of prolonged cloud cover and haze, and provides additional assurance in siting and licensing. In addition, a wide range of enhancement techniques should be employed and different types of image should be color-combined to provide structural and lithologic information. Coastal water circulation can also be studied through repetitive coverage and the inherently synoptic nature of imaging satellites. Among the issues discussed are snow cover, sun angle, and cloud cover, and actual site evaluation studies in the Bataan peninsula of the Philippines and Laguna Verde, California

Developing a Hierarchical Decision Model to Evaluate Nuclear Power Plant Alternative Siting Technologies

Science.gov (United States)

Lingga, Marwan Mossa

A strong trend of returning to nuclear power is evident in different places in the world. Forty-five countries are planning to add nuclear power to their grids and more than 66 nuclear power plants are under construction. Nuclear power plants that generate electricity and steam need to improve safety to become more acceptable to governments and the public. One novel practical solution to increase nuclear power plants' safety factor is to build them away from urban areas, such as offshore or underground. To date, Land-Based siting is the dominant option for siting all commercial operational nuclear power plants. However, the literature reveals several options for building nuclear power plants in safer sitings than Land-Based sitings. The alternatives are several and each has advantages and disadvantages, and it is difficult to distinguish among them and choose the best for a specific project. In this research, we recall the old idea of using the alternatives of offshore and underground sitings for new nuclear power plants and propose a tool to help in choosing the best siting technology. This research involved the development of a decision model for evaluating several potential nuclear power plant siting technologies, both those that are currently available and future ones. The decision model was developed based on the Hierarchical Decision Modeling (HDM) methodology. The model considers five major dimensions, social, technical, economic, environmental, and political (STEEP), and their related criteria and sub-criteria. The model was designed and developed by the author, and its elements' validation and evaluation were done by a large number of experts in the field of nuclear energy. The decision model was applied in evaluating five potential siting technologies and ranked the Natural Island as the best in comparison to Land-Based, Floating Plant, Artificial Island, and Semi-Embedded plant.

War protected underground siting of nuclear power plants -a summary

International Nuclear Information System (INIS)

1974-06-01

In connection with studies concerning the need of war protected nuclear power production the technical and economical conditions with war protection of nuclear power plants have been studied within CDL. Comprehensively one have shown that no technical construction obstacles for siting a nuclear power plant underground exist that the additional costs for underground siting with price level mid 1973 are some 175-250 MSwCr (In today's price level 250 MSwCr will probably correspond to some 300 MSwCr per unit) and that the construction time is some one year longer than for an above ground plant. A study ought to examine more closely the consequences of underground siting from a radiological point of view and what demands on that occasion ought to be put on the technical design. (author)

Plan for addressing issues relating to oil shale plant siting

Energy Technology Data Exchange (ETDEWEB)

Noridin, J. S.; Donovan, R.; Trudell, L.; Dean, J.; Blevins, A.; Harrington, L. W.; James, R.; Berdan, G.

1987-09-01

The Western Research Institute plan for addressing oil shale plant siting methodology calls for identifying the available resources such as oil shale, water, topography and transportation, and human resources. Restrictions on development are addressed: land ownership, land use, water rights, environment, socioeconomics, culture, health and safety, and other institutional restrictions. Descriptions of the technologies for development of oil shale resources are included. The impacts of oil shale development on the environment, socioeconomic structure, water availability, and other conditions are discussed. Finally, the Western Research Institute plan proposes to integrate these topics to develop a flow chart for oil shale plant siting. Western Research Institute has (1) identified relative topics for shale oil plant siting, (2) surveyed both published and unpublished information, and (3) identified data gaps and research needs. 910 refs., 3 figs., 30 tabs.

Nuclear power plant site selection: a case study

International Nuclear Information System (INIS)

Lugasi, Y.; Mehrez, A.; Sinuany-Stern, Z.

1985-01-01

Selecting the site for a nuclear power plant involves the evaluation of numerous criteria and the professional judgment of various experts. The Israel Atomic Energy Commission has been concerned with the problem of selecting a site for a nuclear power station. Previous studies have been performed by the commission to identify potential sites. There were initial screenings where potential sites were chosen according to various minimal criteria and international standards. Only sites that met all the criteria were chosen. A study was made to find the most preferred site among the potential sites that met all the criteria. Two mathematical approaches were used: Keeney's multiattribute utility function and Saaty's eigenvalue prioritization technique. Both models ranked the same site as the most desirable; however, the models differed in their ranking of the other sites

Rocky Flats Plant Site Environmental Report: 1993 Highlights

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

The Rocky Flats Plant Site Environmental Report provides summary information on the plant`s environmental monitoring programs and the results recorded during 1993. The report contains a compliance summary, results of environmental monitoring and other related programs, a review of environmental remediation activities, information on external gamma radiation dose monitoring, and radiation dose estimates for the surrounding population. This section provides an overview of these topics and summarizes more comprehensive discussions found in the main text of this annual report.

Decommissioning strategy and schedule for a multiple reactor nuclear power plant site

Energy Technology Data Exchange (ETDEWEB)

Monteiro, Deiglys Borges; Moreira, Joao M.L.; Maiorino, Jose Rubens, E-mail: deiglys.monteiro@ufabc.edu.br, E-mail: joao.moreira@ufabc.edu.br, E-mail: joserubens.maiorino@ufabc.edu.br [Universidade Federal do ABC (CECS/UFABC), Santo Andre, SP (Brazil). Centro de Engenharia, Modelagem e Ciencias Aplicadas

2015-07-01

The decommissioning is an important part of every Nuclear Power Plant life cycle gaining importance when there are more than one plant at the same site due to interactions that can arise from the operational ones and a decommissioning plant. In order to prevent undesirable problems, a suitable strategy and a very rigorous schedule should implemented and carried. In this way, decommissioning tasks such as fully decontamination and dismantling of activated and contaminated systems, rooms and structures could be delayed, posing as an interesting option to multiple reactor sites. The present work aims to purpose a strategy and a schedule for the decommissioning of a multiple reactor site highlighting the benefits of delay operational tasks and constructs some auxiliary services in the site during the stand by period of the shutdown plants. As a case study, will be presented a three-reactor site which the decommissioning process actually is in planning stage and that should start in the next decade. (author)

Decommissioning strategy and schedule for a multiple reactor nuclear power plant site

International Nuclear Information System (INIS)

Monteiro, Deiglys Borges; Moreira, Joao M.L.; Maiorino, Jose Rubens

2015-01-01

The decommissioning is an important part of every Nuclear Power Plant life cycle gaining importance when there are more than one plant at the same site due to interactions that can arise from the operational ones and a decommissioning plant. In order to prevent undesirable problems, a suitable strategy and a very rigorous schedule should implemented and carried. In this way, decommissioning tasks such as fully decontamination and dismantling of activated and contaminated systems, rooms and structures could be delayed, posing as an interesting option to multiple reactor sites. The present work aims to purpose a strategy and a schedule for the decommissioning of a multiple reactor site highlighting the benefits of delay operational tasks and constructs some auxiliary services in the site during the stand by period of the shutdown plants. As a case study, will be presented a three-reactor site which the decommissioning process actually is in planning stage and that should start in the next decade. (author)

Assessment of social values in thermal plant siting

International Nuclear Information System (INIS)

Anon.

1976-01-01

The objective of the project is to develop a method for combining social values with techno-economic data for better decision making in thermal nuclear power plant siting. Quantified technical impact data which is socially weighted will allow for the optimal choice of site/design alternatives. In this phase, a study of community leadership in energy/environment issues was conducted in a town familiar with a (nuclear) thermal power plant. Secondly, a linear composite analysis of the measurement problems associated with combining diverse scales of impacts was completed. Third, a revision of the social values instrument used in a previous phase of the study was initiated. Finally, liaison activities with utilities were undertaken. Quantification of three of the technical impact factors is currently underway

Tsunami hazard assessment on nuclear power plant site evaluation accordance on DS 417

International Nuclear Information System (INIS)

Akhmad Khusyairi

2011-01-01

Nuclear power plant site evaluation should conduct the hazard evaluation on tsunami. Global climate changes and particularly extreme meteorology and hydrology phenomena have an impact on the structure, systems and important components related to safety. Therefore, IAEA makes efforts to revise the IAEA Safety Standard Series NS-G 3.4, Meteorological Events in Site Evaluation for Nuclear Power Plants and IAEA safety standard series NS-G 3.5 Flood Hazard For Nuclear Power Plants On Coastal And River Sites, in order to provide protection against the public and the environment safety due to operation of nuclear power plants. There are two methods used in assessing tsunami hazard, probabilistic and deterministic methods. In the tsunami hazard assessment, some necessary information and data should be obtained to determine the basic design of tsunami hazard during designing nuclear power plants, especially the cooling system design. Flooding caused tsunami must be evaluated to determine the site protection system. Furthermore, There must be an evaluation on either coincident event or meteorological simultaneously tsunami event that caused the worst effect on the site. Therefore, the protection of the site from extreme tsunami can be planned. (author)

The potential environmental impacts and the siting of proposed nuclear power plants in China

International Nuclear Information System (INIS)

Shi Zhongqi

1986-01-01

This paper reviews briefly the methodology of assessing environmental impacts from the nuclear power plants and analyses the potential radiological impacts on the environment from proposed nuclear power plants in China. Preliminary studies show that the environmental impacts of the effluents of routine release from PWRs to the proposed sites are extremely small, even if nuclear power plants are constructed either on the Bohai Sea shore with a narrow mouth or in the densely populated regions of Sunan. Thus, the suitability of sites depends mainly on the acceptability of possible exposure to the residents following postulated accidental release of radioactive materials. The paper also discusses relations between the nuclear plant siting and population distribution around the site and compares the distribution of the proposed sites in China with that of other countries sites in according to China actual situation, it is reasonable to adopt a prudent policy that the first series of nuclear power plants in China should be built in relatively low population areas

Toward a regional power plant siting method: AEC-Maryland regional siting factors study, FY 1974 progress report

International Nuclear Information System (INIS)

Yaffee, S.L.; Miller, C.A.

1974-11-01

The ''AEC-Maryland Regional Siting Factors Study'' examines the process of siting in a regional context. It is developing an analysis method to delineate candidate areas for siting of several power plant technology packages, including both fossil-fueled and nuclear options. Tools that are being used include simulation modeling, economic and demographic forecasting, spatial analysis, and computer graphics and numerical manipulation. The approach will describe the trade-offs incurred if a power plant is located in one candidate area rather than in another. In FY 1974, a suitability analysis method was developed which uses engineering and environmental parameters to define a level of environmental cost incurred if a segment of land is used to site a specific technology package. (U.S.)

Numerical Simulation of Groundwater Flow at Kori Nuclear Power Plant Site

International Nuclear Information System (INIS)

Sohn, Wook; Sohn, Soon Whan; Chon, Chul Min; Kim, Kue Youn

2010-01-01

Recently, the understanding of hydrogeological characteristics of nuclear power sites is getting more importance with increasing public concerns over the environment since such understanding is essential for an environmentally friendly operation of plants. For such understanding, the prediction of groundwater flow pattern onsite plays the most critical role since it is the most dynamic of the factors to be considered. In this study, the groundwater flow at the Kori Plant 1 site has been simulated numerically with aim of providing fundamental information needed for improving the understanding of the hydrogeological characteristics of the site

Portsmouth Gaseous Diffusion Plant annual site environmental report for 1993

Energy Technology Data Exchange (ETDEWEB)

Horak, C.M. [ed.

1994-11-01

This calendar year (CY) 1993 annual report on environmental monitoring of the US Department of Energy`s (DOE`s) Portsmouth Gaseous Diffusion Plant (Portsmouth) and its environs consists of three separate documents: a summary pamphlet for the general public; a more detail discussion and of compliance status, data, and environmental impacts (this document); and a volume of detailed data that is available on request. The objectives of this report are to report compliance status during 1993; provide information about the plant site and plant operations; report 1993 monitoring data for the installation and its environs that may have been affected by operations on the plant site; document information on input and assumptions used in calculations; provide trend analyses (where appropriate) to indicate increases and decreases in environmental impact, and provide general information on quality assurance for the environmental monitoring program.

Portsmouth Gaseous Diffusion Plant annual site environmental report for 1993

International Nuclear Information System (INIS)

Horak, C.M.

1994-11-01

This calendar year (CY) 1993 annual report on environmental monitoring of the US Department of Energy's (DOE's) Portsmouth Gaseous Diffusion Plant (Portsmouth) and its environs consists of three separate documents: a summary pamphlet for the general public; a more detail discussion and of compliance status, data, and environmental impacts (this document); and a volume of detailed data that is available on request. The objectives of this report are to report compliance status during 1993; provide information about the plant site and plant operations; report 1993 monitoring data for the installation and its environs that may have been affected by operations on the plant site; document information on input and assumptions used in calculations; provide trend analyses (where appropriate) to indicate increases and decreases in environmental impact, and provide general information on quality assurance for the environmental monitoring program

Cytochrome c1 exhibits two binding sites for cytochrome c in plants.

Science.gov (United States)

Moreno-Beltrán, Blas; Díaz-Quintana, Antonio; González-Arzola, Katiuska; Velázquez-Campoy, Adrián; De la Rosa, Miguel A; Díaz-Moreno, Irene

2014-10-01

In plants, channeling of cytochrome c molecules between complexes III and IV has been purported to shuttle electrons within the supercomplexes instead of carrying electrons by random diffusion across the intermembrane bulk phase. However, the mode plant cytochrome c behaves inside a supercomplex such as the respirasome, formed by complexes I, III and IV, remains obscure from a structural point of view. Here, we report ab-initio Brownian dynamics calculations and nuclear magnetic resonance-driven docking computations showing two binding sites for plant cytochrome c at the head soluble domain of plant cytochrome c1, namely a non-productive (or distal) site with a long heme-to-heme distance and a functional (or proximal) site with the two heme groups close enough as to allow electron transfer. As inferred from isothermal titration calorimetry experiments, the two binding sites exhibit different equilibrium dissociation constants, for both reduced and oxidized species, that are all within the micromolar range, thus revealing the transient nature of such a respiratory complex. Although the docking of cytochrome c at the distal site occurs at the interface between cytochrome c1 and the Rieske subunit, it is fully compatible with the complex III structure. In our model, the extra distal site in complex III could indeed facilitate the functional cytochrome c channeling towards complex IV by building a "floating boat bridge" of cytochrome c molecules (between complexes III and IV) in plant respirasome. Copyright © 2014 Elsevier B.V. All rights reserved.

Survival and growth of restored Piedmont riparian forests as affected by site preparation, planting stock, and planting aids

Science.gov (United States)

Chelsea M. Curtis; W. Michael Aust; John R. Seiler; Brian D. Strahm

2015-01-01

Forest mitigation sites may have poor survival and growth of planted trees due to poor drainage, compacted soils, and lack of microtopography. The effects of five replications of five forestry mechanical site preparation techniques (Flat, Rip, Bed, Pit, and Mound), four regeneration sources (Direct seed, Bare root, Tubelings, and Gallon), and three planting aids (None...

Blasting jobs on the building site of the Temelin nuclear power plant

International Nuclear Information System (INIS)

Voda, J.; Podel, R.

1984-01-01

The problems are discussed of the preparation and implementation on the Temelin nuclear power plant building site of blasting, the volume of drilling and the choice of the drill hammer - all based on experience gained during the construction of the Mochovce nuclear power plant. The amount of explosives used on the Temelin site will be 1400 t. The use of mechanical charging may shorten the preparation of the site by 20 to 30%. Explosive emulsion slurries are being developed from home raw materials whose application will reduce the volume of drilling by 15%. The method of controlled breaking secures adequate quality of peripheral walls and bottom chink but special explosives will have to be used. Seismic effects are discussed of blasting on dwellings, agricultural and industrial buildings in the vicinity of the site, on-site buildings, underground mains and special structures of the nuclear power plant. (E.S.)

Safety criteria for siting a nuclear power plant

International Nuclear Information System (INIS)

2001-01-01

The guide sets forth requirements for safety of the population and the environment in nuclear power plant siting. It also sets out the general basis for procedures employed by other competent authorities when they issue regulations or grant licences. On request STUK (Radiation and Nuclear Safety Authority of Finland) issues case-specific statements about matters relating to planning and about other matters relating to land use in the environment of nuclear power plants

Utility survey on nuclear power plant siting and nuclear energy centers

International Nuclear Information System (INIS)

Cope, D.F.; Bauman, H.F.

1977-01-01

Most of the large U.S. utilities were surveyed by telephone and mail on questions concerning nuclear power plant siting and nuclear energy centers (NECs). The main purpose of the survey was for guidance of ERDA's NEC program. The questions covered the following topics: availability of sites; impact of environmental and other restraints; plans for development of multi-unit sites; interest in NEC development; interest in including fuel-cycle facilities in NECs; and opinions on the roles desired for the state and Federal governments in power plant siting. The main conclusion of the survey was that, while many utilities were considering multiple-unit sites of 2 to 5 units, none were planning larger energy centers at the present time. However, several expressed interest in NECs as a long-range future development

The part played by applied geology in nuclear power plant site studies

International Nuclear Information System (INIS)

Giafferi, J.L.

1994-01-01

Site-related geological problems are one of the constraints affecting the environment of nuclear power plants. The natural features (soil and subsoil) at the nuclear power plant site affect numerous factors in the design, construction and operation of the civil engineering structures. The site geological criteria are not solely restricted to the soil as a static support for the structures. Earth tremors in France are of moderate intensity but the likelihood of their occurrence must nevertheless be taken into account for each site. Studies must concern the geological and seismic features of the region as well as the soil and subsoil configurations and composition in the immediate vicinity of the site in order to determine the physical characteristics of the earthquakes so that the safety of the plant can be guaranteed; in many cases, water tables have also to be taken into consideration. Geologic survey techniques are discussed. 13 figs., 7 refs

The Choice of Sites for the First Nuclear Power Plants in Brazil

International Nuclear Information System (INIS)

Cintra do Prado, L.

1966-01-01

In selecting the sites for nuclear power plants a decision has to be taken as to (1) which area of the country is best suited for the purpose - e.g. the area of Recife, Rio or Sao Paulo, etc. - given the trend in energy requirements and the availability of resources, and (2) where to site the plant or plants within that area. In this paper I shall concentrate on the first of these problems and shall be concerned with assessing the merits and demerits of installing nuclear power plants in certain regions of Brazil which seem particularly well suited for the purpose

Rocky Flats Plant Site Environmental Report: 1993 Highlights

International Nuclear Information System (INIS)

1993-01-01

The Rocky Flats Plant Site Environmental Report provides summary information on the plant's environmental monitoring programs and the results recorded during 1993. The report contains a compliance summary, results of environmental monitoring and other related programs, a review of environmental remediation activities, information on external gamma radiation dose monitoring, and radiation dose estimates for the surrounding population. This section provides an overview of these topics and summarizes more comprehensive discussions found in the main text of this annual report

Selection of sites for nuclear power plants in The Netherlands. Pt. A

International Nuclear Information System (INIS)

1985-01-01

In this report a policy proposal is presented concerning the selection of location sites for new nuclear power plants in the Netherlands. Firstly it is investigated which of the 29 already selected location sites are not to be taken into further account because of obvious obstructions (close vicinity of a big city etc.). The remaining sites are judged on the base of local population magnitude. The sites that pass the last criteria are relatively compared from a large number of viewpoints. To round off the selection procedure the government will explain why they consider the finally selected sites to be suitable for location of new nuclear power plants. Steps are indicated to prevent the decrease of planologic suitability of the selected location sites. (Auth.)

Power from waste. [Power plant at landfill site

Energy Technology Data Exchange (ETDEWEB)

Anon,

1991-01-01

Base Load Systems Ltd, a company in the United Kingdom, has just commissioned a power plant in Leicestershire which uses waste gases from a landfill site. The gases power two specially modified turbo charged engine and generator packages. The plant will use approximately 100 cu meters of landfill gas per hour and is expected to feed 1.5MW of electrical power into the supply network of East Midlands Electricity. Once the landfill site has been completely filled and capped with clay, it is estimated that the electrical power output will be 4 MW. At present, since their are no customers for heat in the vicinity, 100 KW of the electricity produced are used to run fans to dissipate the 2.5 MW of waste heat. Base load is also involved elsewhere in combined heat and power projects. (UK).

Siting and early-stage project management of nuclear power plant

International Nuclear Information System (INIS)

Wang Kai; Li Guojin

2013-01-01

In this paper, difficulties and challenges facing in siting of nuclear power plant after Fukushima nuclear accident is introduced. The key points for siting are analyzed. The site characteristics related to nuclear safety and the evaluated methods are discussed. From project management perspective, main procedures and key points for the early-stage of a nuclear power project are described. (authors)

ESPSD, Nuclear Power Plant Siting Database

International Nuclear Information System (INIS)

Slezak, S.

2001-01-01

1 - Description of program or function: This database is a repository of comprehensive licensing and technical reviews of siting regulatory processes and acceptance criteria for advanced light water reactor (ALWR) nuclear power plants. The program is designed to be used by applicants for an early site permit or combined construction permit/operating license (10CFRR522), Sub-parts A and C) as input for the development of the application. The database is a complete, menu-driven, self-contained package that can search and sort the supplied data by topic, keyword, or other input. The software is designed for operation on IBM compatible computers with DOS. 2 - Method of solution: The database is an R:BASE Runtime program with all the necessary database files included

Problems in Siting Nuclear Power Plants in Japan and Efforts to Solve Them

Energy Technology Data Exchange (ETDEWEB)

Inouye, T. [Ministry of International Trade and Industry, Tokyo (Japan)

1967-09-15

The rapidly growing demand for energy in Japan will require a total capacity of 30 to 40 thousand MW(e) in nuclear power by 1985. Materialization of this development programme must naturally be supported by securing the requisite sites for the nuclear power plants. The following factors make siting of nuclear power plants more difficult in Japan than in any other country: a small, densely populated territory with little level land, that is already completely utilized for agricultural and/or industrial purposes; small rivers and an active marine-product industry developed along most of the seacoasts, both of which create difficult cooling-water problems; frequent earthquakes; and the fear of possible radioactivity, which prevails in the only nation in the world to have suffered from the atomic bomb. There are at present four nuclear power plants in operation or under construction in Japan with a total capacity of about 1.3 thousand MW(e). However, the plants in these construction programmes have been sited on the basis of taking the easiest course available although there were several possible solutions to choose from. It is pointed out here that the long-range nuclear power development programme will call for a fundamental solution to enable siting a large number of power plants under the adverse conditions in Japan. Accordingly, a study was made, which included quantitative analyses of reactor siting factors and suggested measures for solving the siting problems. The analyses were based on nuclear power plant sites assumed to be located on the seacoast and characterized by low-population density, desirable geology and favourable topography. It was assumed that seacoast siting was more economical than inland siting. Although the study was made by a general survey using maps, it was shown that approximately 10% of the total coastline areas would be eligible for reactor siting, but most of these areas in this case are located in the northern part of Japan, far from

The knowledge-based off-site emergency response system for a nuclear power plant

International Nuclear Information System (INIS)

Ho, L.W.; Loa, W.W.; Wang, C.L.

1987-01-01

A knowledge-based expert system for a nuclear power plant off-site emergency response system is described. The system incorporates the knowledge about the nuclear power plant behaviours, site environment and site geographic factors, etc. The system is developed using Chinshan nuclear power station of Taipower Company, Taiwan, ROC as a representative model. The objectives of developing this system are to provide an automated intelligent system with functions of accident simulation, prediction and with learning capabilities to supplement the actions of the emergency planners and accident managers in order to protect the plant personnel and the surrounding population, and prevent or mitigate property damages resulting from the plant accident. The system is capable of providing local and national authorities with rapid retrieval data from the site characteristics and accident progression. The system can also provide the framework for allocation of available resources and can handle the uncertainties in data and models

Synthesis gas demonstration plant program, Phase I. Site confirmation report

Energy Technology Data Exchange (ETDEWEB)

1978-12-01

With few reservations, the Baskett, Kentucky site exhibits the necessary characteristics to suggest compatibility with the proposed Synthesis Gas Demonstration Plant Project. An evaluation of a broad range of technical disciplinary criteria in consideration of presently available information indicated generally favorable conditions or, at least, conditions which could be feasibly accommodated in project design. The proximity of the Baskett site to market areas and sources of raw materials as well as a variety of transportation facilities suggests an overall favorable impact on Project economic feasibility. Two aspects of environmental engineering, however, have been identified as areas where the completion or continuation of current studies are required before removing all conditions on site suitability. The first aspect involves the current contradictory status of existing land use and planning ordinances in the site area. Additional investigation of the legality of, and local attitudes toward, these present plans is warranted. Secondly, terrestrial and aquatic surveys of plant and animal life species in the site area must be completed on a seasonal basis to confirm the preliminary conclusion that no exclusionary conditions exist.

Dose assessments in nuclear power plant siting

International Nuclear Information System (INIS)

1988-03-01

This document is mainly intended to provide information on dose estimations and assessments for the purpose of nuclear power plant (NPP) siting. It is not aimed at giving radiation protection guidance, criteria or procedures to be applied during the process of NPP siting nor even to provide recommendations on this subject matter. The document may however be of help for implementing some of the Nuclear Safety Standards (NUSS) documents on siting. The document was prepared before April 26, 1986, when a severe accident at the Unit 4 of Chernobyl NPP in the USSR had occurred. It should be emphasized that this document does not bridge the gap which exists in the NUSS programme as far as radiation protection guidance for the specific case of siting of NPP is concerned. The Agency will continue to work on this subject with the aim to prepare a safety series document on radiation protection requirements for NPP siting. This document could serve as a working document for this purpose. Refs, figs and tabs

Selection of sites for nuclear power plants in The Netherlands. Pt. C

International Nuclear Information System (INIS)

1986-01-01

This advice is concerned with the question where possible new nuclear power plants can at best be sited in the Netherlands. Safety risks of power plants are considered (sourceterm analysis, meteorologic aspects). A site analysis is presented on the base of criteria like population density, possible emergency provisions, contamination of agricultural areas etc. Reports of several committees are included. (Auth.)

Independent verification in operations at nuclear power plants: Summaries of site visits

International Nuclear Information System (INIS)

Donderi, D.C.; Smiley, A.; Ostry, D.J.; Moray, N.P.

1995-09-01

A critical review of approaches to independent verification in operations used in nuclear power plant quality assurance programs in other countries was conducted and are detailed in volume 1. This paper is a compilation of the visits to nuclear power plant sites to study independent verification in operations at sites in Canada, USA, Japan, United Kingdom, France and Germany. 3 tabs., 22 figs

RNA polyadenylation sites on the genomes of microorganisms, animals, and plants.

Directory of Open Access Journals (Sweden)

Xiu-Qing Li

Full Text Available Pre-messenger RNA (mRNA 3'-end cleavage and subsequent polyadenylation strongly regulate gene expression. In comparison with the upstream or downstream motifs, relatively little is known about the feature differences of polyadenylation [poly(A] sites among major kingdoms. We suspect that the precise poly(A sites are very selective, and we therefore mapped mRNA poly(A sites on complete and nearly complete genomes using mRNA sequences available in the National Center for Biotechnology Information (NCBI Nucleotide database. In this paper, we describe the mRNA nucleotide [i.e., the poly(A tail attachment position] that is directly in attachment with the poly(A tail and the pre-mRNA nucleotide [i.e., the poly(A tail starting position] that corresponds to the first adenosine of the poly(A tail in the 29 most-mapped species (2 fungi, 2 protists, 18 animals, and 7 plants. The most representative pre-mRNA dinucleotides covering these two positions were UA, CA, and GA in 17, 10, and 2 of the species, respectively. The pre-mRNA nucleotide at the poly(A tail starting position was typically an adenosine [i.e., A-type poly(A sites], sometimes a uridine, and occasionally a cytidine or guanosine. The order was U>C>G at the attachment position but A>>U>C≥G at the starting position. However, in comparison with the mRNA nucleotide composition (base composition, the poly(A tail attachment position selected C over U in plants and both C and G over U in animals, in both A-type and non-A-type poly(A sites. Animals, dicot plants, and monocot plants had clear differences in C/G ratios at the poly(A tail attachment position of the non-A-type poly(A sites. This study of poly(A site evolution indicated that the two positions within poly(A sites had distinct nucleotide compositions and were different among kingdoms.

Issues at manufactured gas plant sites

International Nuclear Information System (INIS)

Menzie, C.A.; Unites, D.F.; Nakles, D.

1991-01-01

Gas, manufactured from coal or oil was used to light and heat homes, industries, and streets of this country from the mid-1800s to the late 1940s or early 1950s. The era, with its associated gas lights, faded with the development of natural gas supplies and direct use of other fossil fuels. Today, Manufactured Gas Plant (MGP) sites are part of our history. Most of the MGPs were operated at a time when the state of the environmental sciences was much less sophisticated and the environmental regulations were much less stringent or nonexistent. While there was an awareness of potential environmental problems then the concerns were more qualitative (e.g., odor, color) and resulted in minimal treatment of process residuals. Inasmuch as there may be over a thousand MGP sites in the United States, it also became clear that utility research institutes such as the Gas Research Institute (GRI) and the Electric Power Research Institute (EPRI) should address key research and management issues related to site investigation, risk assessment, and site remediation. Information gained from these research initiatives would serve the industry as a whole, as well as other groups involved in the assessment of MGP sites. This paper provides and overview of these programs and identifies how additional information can be obtained

Meteorological events in site evaluation for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2005-01-01

This Safety Guide provides recommendations and guidance on conducting hazard assessments of extreme and rare meteorological phenomena. It is of interest to safety assessors and regulators involved in the licensing process as well as to designers of nuclear power plants. This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It supplements the IAEA Safety Requirements publication on Site Evaluation for Nuclear Facilities which is to supersede the Code on the Safety of Nuclear Power Plants: Siting, Safety Series No. 50-C-S (Rev. 1), IAEA, Vienna (1988). The present Safety Guide supersedes two earlier Safety Guides: Safety Series No. 50-SG-S11A (1981) on Extreme Meteorological Events in Nuclear Power Plant Siting, Excluding Tropical Cyclones and Safety Series No. 50-SG-S11B (1984) on Design Basis Tropical Cyclone for Nuclear Power Plants. The purpose of this Safety Guide is to provide recommendations and guidance on conducting hazard assessments of extreme and rare meteorological phenomena. This Safety Guide provides interpretation of the Safety Requirements publication on Site Evaluation for Nuclear Facilities and guidance on how to fulfil these requirements. It is aimed at safety assessors or regulators involved in the licensing process as well as designers of nuclear power plants, and provides them with guidance on the methods and procedures for analyses that support the assessment of the hazards associated with extreme and rare meteorological events. This Safety Guide discusses the extreme values of meteorological variables and rare meteorological phenomena, as well as their rates of occurrence, according to the following definitions: (a) Extreme values of meteorological variables such as air temperature and wind speed characterize the meteorological or climatological environment. And (b) Rare meteorological phenomena

Evaluation of regulatory processes affecting nuclear power plant early site approval and standardization

International Nuclear Information System (INIS)

1983-12-01

This report presents the results of a survey and evaluation of existing federal, state and local regulatory considerations affecting siting approval of power plants in the United States. Those factors that may impede early site approval of nuclear power plants are identified, and findings related to the removal of these impediments and the general improvement of the approval process are presented. A brief evaluation of standardization of nuclear plant design is also presented

Regulatory requirements for nuclear power plant site selection in Malaysia-a review.

Science.gov (United States)

Basri, N A; Hashim, S; Ramli, A T; Bradley, D A; Hamzah, K

2016-12-01

Malaysia has initiated a range of pre-project activities in preparation for its planned nuclear power programme. Clearly one of the first steps is the selection of sites that are deemed suitable for the construction and operation of a nuclear power plant. Here we outline the Malaysian regulatory requirements for nuclear power plant site selection, emphasizing details of the selection procedures and site characteristics needed, with a clear focus on radiation safety and radiation protection in respect of the site surroundings. The Malaysia Atomic Energy Licensing Board (AELB) site selection guidelines are in accord with those provided in International Atomic Energy Agency (IAEA) and United Stated Nuclear Regulatory Commission (USNRC) documents. To enhance the suitability criteria during selection, as well as to assist in the final decision making process, possible assessments using the site selection characteristics and information are proposed.

Dechlorane Plus (DP) in air and plants at an electronic waste (e-waste) site in South China

Energy Technology Data Exchange (ETDEWEB)

Chen Shejun [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Tian Mi; Wang Jing; Shi Tian [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate School, Chinese Academy of Sciences, Beijing 100049 (China); Luo Yong [Guangdong Forestry Survey and Planning Institute, Guangzhou 510520 (China); Luo Xiaojun [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Mai Bixian, E-mail: nancymai@gig.ac.cn [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2011-05-15

Air and foliage samples (Eucalyptus spp. and Pinus massoniana Lamb.) were collected from e-waste and reference sites in South China and analyzed for Dechlorane Plus (DP) and two dechlorinated DPs. DP concentrations in the air were 13.1-1794 pg/m{sup 3} for the e-waste site and 0.47-35.7 pg/m{sup 3} for the reference site, suggesting the recycling of e-waste is an important source of DP to the environment. Plant DP, with concentrations of 0.45-51.9 ng/g dry weight at the e-waste site and 0.09-2.46 ng/g at the reference site, exhibited temporal patterns similar to the air DP except for pine needle at the reference site. The air-plant exchange of DP could be described with the two-compartment model. Anti-Cl{sub 11} DP was measured in most air and plant samples from the e-waste site. The ratios of anti-Cl{sub 11} DP to anti-DP in the air and plants may indicate the preferential uptake of dechlorinated DP by plant compared with DP. - Highlights: > Dechlorane Plus was widely present in the air and plants in South China. > Temporal patterns of the plant DP could be described with the two-compartment model. > Plant uptake can efficiently reduce air DP concentration at the reference site. > Anti-Cl{sub 11} DP was measured in most air and plant samples from the e-waste site. - E-waste recycling in South China results in wide occurrence of DP in the air and plant.

A COUNTY-LEVEL MODEL OF MANUFACTURING PLANT RECRUITMENT WITH IMPROVED INDUSTRIAL SITE QUALITY MEASUREMENT

OpenAIRE

Kriesel, Warren; McNamara, Kevin T.

1991-01-01

Empirical analysis of manufacturing plant location requires the use of a single industrial site quality measure. Under hedonic price theory, the price of industrial sites can be explained by their quality characteristics. The estimated site price is included with ten other location factors in an ordered, categorical logit model of plant attraction to Georgia counties. The results inform public decision-makers of the relative impact of site location factors and how changes in location factors ...

Nuclear power plant attempts in Turkey and the first licensed site

International Nuclear Information System (INIS)

Bektur, Y.; Bezdegumeli, U.

2004-01-01

In this paper, detailed information regarding Turkey's past attempts for the construction of a nuclear power plant (NPP) and site survey studies conducted for this plant is given. Also, some important characteristics of the first licensed site, namely Akkuyu, are summarized. There were four attempts made for the construction of an NPP in the past. However, all of them failed due to technical, economical and/or some other reasons. Akkuyu site has been selected among around 25 candidate sites for the reasons that bulky materials can be transported there by sea; it is located near the major electricity demand centers; soil-structure interaction and slab stability are suitable for the construction of an NPP; its surrounding is one of the most sparsely populated areas of Turkey; and it is seismically the most stable region in earthquake-prone Turkey, e.g. Turkish Electricity Authority (TEK) was granted a site license for the Akkuyu in 1976. (author)

Quaternary ground siting technology of nuclear power plants

International Nuclear Information System (INIS)

Nishi, K.; Kokusho, T.; Iwatate, Y.; Ishida, K.; Honsho, S.; Okamoto, T.; Tohma, J.; Tanaka, Y.; Kanatani, M.

1992-01-01

A seismic stability evaluation method for a nuclear power plant to be located on Quaternary sandy/gravelly ground is discussed herein in terms of a geological and geotechnical survey, a design earthquake motion evaluation and geotechnical seismic stability analyses. The geological and geotechnical exploration tunnel in the rock foundation siting will be difficult in the Quaternary ground siting. Boring, geophysical surveys and soil sampling will play a major role in this case. A design earthquake input spectrum for this siting is proposed to take in account the significant effect of longer period motion on ground stability. Equivalent and non-linear analyses demonstrate the seismic stability of the foundation ground so long as the soil density is high. (author)

Case study of manufactured gas plant site remediations using thermal desorption

Energy Technology Data Exchange (ETDEWEB)

Vogel, R.G.; Hayes, T.; Slimon, K.F.; Unites, D. [Southern California Gas Company, Los Angeles, CA (United States)

1995-12-31

Southern California Gas Company (SoCal Gas) has recently remediated five of its former manufactured gas plant (MGP) sites using on-site and off-site thermal desorption. This technology has proven effective in the treatment of PAH-contaminated soils with widely variable concentrations. At two of the five sites, MGP-contaminated materials were excavated and thermally treated on site. At the other sites, MGP-contaminated materials were excavated and transported directly to an off-site thermal desorber. Much of the production was of oil-gas, giving lampblack contamination, but some coal tar was also present.

An integrated approach to site selection for nuclear power plants

International Nuclear Information System (INIS)

Hassan, E.M.A.

1975-01-01

A method of analysing and evaluating the large number of factors influencing site selection is proposed, which can interrelate these factors and associated problems in an integrated way and at the same time establish a technique for site evaluation. The objective is to develop an integrated programme that illustrates the complexity and dynamic interrelationships of the various factors to develop an improved understanding of the functions and objectives of siting nuclear power plants and would aim finally at the development of an effective procedure and technique for site evaluation and/or comparative evaluation for making rational site-selection decisions. (author)

The site of a nuclear power plant and environmental safety; Ydinvoimalaitoksen sijaintipaikka ja ympaeristoen turvallisuus

Energy Technology Data Exchange (ETDEWEB)

Rossi, J. [VTT Energy, Espoo (Finland)

2001-11-01

The purpose of this report is to give the reader a general view of the things associated with the site of a nuclear power plant. In this context the effect of a nuclear power plant and site on environmental safety is considered. Planning, construction and operating a nuclear power plant require several judgements and licenses based on different laws. The location of the planned nuclear facility project and environmental conditions contribute in great detail to the compliance arguments of permits. At first the environmental impacts of the siting project and its alternatives shall be investigated in the Environmental Impact Assessment procedure. Then the decision in principle according to the Nuclear Energy Act can be applied from the Council of State, the decision shall further be confirmed by Parliament. When the decision in principle is considered the overall good of society shall be assessed by means of considering i.a. site alternatives and safety. The safety related basic principle is that operation of a nuclear power plant may not cause danger to the environment, public or property. After the affirmative principle approval the construction license and later on the operation license can be applied from the Council of State, these licenses need to be supported i.a. by building and environmental licenses of separate authorities. Also some international contracts concern realisation of a nuclear power plant siting. The nuclear power plant site shall be suitable for the needs of the electricity production and the transmission system and it shall be technically appropriate for building and operation of a power plant. The site shall be safe enough on the other hand from the view of external events threatening the power plant - although one can be partly prepared for these things in the design of the plant - and on the other hand from the point of public safety. Requirements for the safety of the site are directed in the decision of the Council of State's general

Manual on quality assurance for the survey, evaluation and confirmation of nuclear power plant sites

International Nuclear Information System (INIS)

1987-04-01

The present Manual on Quality Assurance for the Survey, Evaluation and Confirmation of Nuclear Power Plant Sites contains supporting material and illustrates examples for implementing the requirements contained in the Code of Practice on Quality Assurance for Safety in Nuclear Power Plants to the activities of survey, evaluation and confirmation of nuclear power plant sites. At the same time the Code of Practice for Safety in Nuclear Power Plant Siting, and Safety Guides in the siting series contain requirements and recommendations to implement a quality assurance programme in selected activities of the siting process. This manual is intended to provide guidance and illustrate examples on this implementation. During preparation and reviews of this Manual it was found out that the methodology of implementation of the quality assurance programme in siting activities is still under development. For these reasons it was considered appropriate to publish this Manual as a temporary publication for trial use

Ecological investigations at the Pantex Plant Site, 1992

International Nuclear Information System (INIS)

Cushing, C.E.; Mazaika, R.R.; Phillips, R.C.

1993-09-01

In 1992, Pantex requested that Pacific Northwest Laboratory (PNL) conduct a series of ecological surveys to provide baseline information for designing detailed ecological studies on the various ecosystems present at the Pantex plant site near Amarillo, Texas. To this end, PNL scientist and technicians visited the site at different times to conduct investigations and collect samples: July 6--13: birds, small mammals, general habitat assessment; August 10--14: wetland vegetation, birds, small mammals, Playa invertebrates; and September 7--11: birds, small mammals. This report presents the results of these three surveys

Analysis of extreme hydrometric values in the nuclear power plants siting

International Nuclear Information System (INIS)

Gomez, H.R.; Maggio, G.E.; Tripoli, C.R.

1983-01-01

The atucha nuclear power plants are located on the right shore of the Parana de las Palmas river in the entire transition between a fluvial regime and other of tides. Since the disponibility of cooling water is one of the factors to take into account when choosing the nuclear power plant site, it is essential to perform a probabilistic study of extreme hydrometric values. Deterministic and historical analysis should be done to complete the studies already mentioned, in order to establish the values of probable maximum floods. From the application of these methods, it is concluded that the site of the Atucha nuclear power plants constitutes a hydrometric singularity, so that, an optimization has been obtained from that point of view. (Author) [es

Waste Isolation Pilot Plant 2001 Site Environmental Report

Energy Technology Data Exchange (ETDEWEB)

Westinghouse TRU Solutions, Inc.

2002-09-20

The United States (U.S.) Department of Energy's (DOE) Carlsbad Field Office (CBFO) and Westinghouse TRU Solutions LLC (WTS) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environmental, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2001 Site Environmental Report summarizes environmental data from calendar year (CY) 2001 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH- 0173T), and the Waste Isolation Pilot Plant Environmental Protection Implementation Plan (DOE/WIPP 96-2199). The above Orders and guidance documents require that DOE facilities submit an annual site environmental report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health; and the New Mexico Environment Department (NMED). The purpose of this report is to provide a comprehensive description of operational environmental monitoring activities, to provide an abstract of environmental activities conducted to characterize site environmental management performance to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit at WIPP during CY 2001. WIPP received its first shipment of waste on March 26, 1999. In 2001, no evidence was found of any adverse effects from WIPP on the surrounding environment.

Waste Isolation Pilot Plant 2001 Site Environmental Report

International Nuclear Information System (INIS)

Westinghouse TRU Solutions, Inc.

2002-01-01

The United States (U.S.) Department of Energy's (DOE) Carlsbad Field Office (CBFO) and Westinghouse TRU Solutions LLC (WTS) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environmental, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2001 Site Environmental Report summarizes environmental data from calendar year (CY) 2001 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH- 0173T), and the Waste Isolation Pilot Plant Environmental Protection Implementation Plan (DOE/WIPP 96-2199). The above Orders and guidance documents require that DOE facilities submit an annual site environmental report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health; and the New Mexico Environment Department (NMED). The purpose of this report is to provide a comprehensive description of operational environmental monitoring activities, to provide an abstract of environmental activities conducted to characterize site environmental management performance to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit at WIPP during CY 2001. WIPP received its first shipment of waste on March 26, 1999. In 2001, no evidence was found of any adverse effects from WIPP on the surrounding environment

Waste Isolation Pilot Plant 1999 Site Environmental Report

Energy Technology Data Exchange (ETDEWEB)

Evans, Roy B.; Adams, Amy; Martin, Don; Morris, Randall C.; Reynolds, Timothy D.; Warren, Ronald W.

2000-09-30

The U.S. Department of Energy's (DOE)Carlsbad Area Office and the Westinghouse Waste Isolation Division (WID) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environmental, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 1999 Site Environmental Report summarizes environmental data from calendar year 1999 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH- 0173T), and the Waste Isolation Pilot Plant Environmental Protection Implementation Plan (DOE/WIPP 96-2199). The above orders and guidance documents require that DOE facilities submit an Annual Site Environmental Report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health. The purpose of this report is to provide a comprehensive description of operational environmental monitoring activities, to provide an abstract of environmental activities conducted to characterize site environmental management performance to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit at WIPP during calendar year 1999. WIPP received its first shipment of waste on March 26, 1999. In 1999, no evidence was found of any adverse effects from WIPP on the surrounding environment. Radionuclide concentrations in the environment surrounding WIPP were not statistically higher in 1999 than in 1998.

The subject deserving wide attention for nuclear power plant siting and environmental impact assessment

International Nuclear Information System (INIS)

Li Yong; Li Wenhui; Zhang Lingyan

2009-01-01

Based on siting work of nuclear power plant, the characteristics of nuclear power plant site selection and environmental impact assessment are analysed in accordance with laws and regulations of nuclear safety and environmental protection. Some subjects deserving attentions are put forward. (authors)

Site infrastructure as required during the construction and erection of nuclear power plants

International Nuclear Information System (INIS)

Haas, K.F.; Wagner, H.

1978-01-01

In general, in an exchange of experience on constructing nuclear power plants priority is given to design and lay-out, financing, quality assurance etc., but in this paper an attempt has been made to describe range and type of site infrastructure required during construction and erection. Site infrastructure will make considerable demands on the planning, supply of material and maintenance that may result from the frequently very isolated location of power plant sites. Examples for specific values and experiences are given for a nuclear power plant with two units on the 1300-MW type at present under construction of the Persian Gulf in Iran. Data concerning the site infrastructure, including examples, are given and explained on the basis of graphs. The site is split up into a technical and a social infrastructure. The main concern of the technical site infrastructure is the timely provision and continuous availability of electric energy, water, communication grids, workshops, warehouses, offices, transport and handling facilities, as well as the provision of heavy load roads, harbour facilities, etc. The social site infrastructure in general comprises accommodation, food supplies and the care and welfare of all site personnel, which includes a hospital, school, self-service shop, and sport and recreation facilities. (author)

Site fidelity by bees drives pollination facilitation in sequentially blooming plant species.

Science.gov (United States)

Ogilvie, Jane E; Thomson, James D

2016-06-01

Plant species can influence the pollination and reproductive success of coflowering neighbors that share pollinators. Because some individual pollinators habitually forage in particular areas, it is also possible that plant species could influence the pollination of neighbors that bloom later. When flowers of a preferred forage plant decline in an area, site-fidelity may cause individual flower feeders to stay in an area and switch plant species rather than search for preferred plants in a new location. A newly blooming plant species may quickly inherit a set of visitors from a prior plant species, and therefore experience higher pollination success than it would in an area where the first species never bloomed. To test this, we manipulated the placement and timing of two plant species, Delphinium barbeyi and later-blooming Gentiana parryi. We recorded the responses of individually marked bumble bee pollinators. About 63% of marked individuals returned repeatedly to the same areas to forage on Delphinium. When Delphinium was experimentally taken out of bloom, most of those site-faithful individuals (78%) stayed and switched to Gentiana. Consequently, Gentiana flowers received more visits in areas where Delphinium had previously flowered, compared to areas where Delphinium was still flowering or never occurred. Gentiana stigmas received more pollen in areas where Delphinium disappeared than where it never bloomed, indicating that Delphinium increases the pollination of Gentiana when they are separated in time. Overall, we show that individual bumble bees are often site-faithful, causing one plant species to increase the pollination of another even when separated in time, which is a novel mechanism of pollination facilitation.

External human induced events in site evaluation for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

The purpose of the present Safety Guide is to provide recommendations and guidance for the examination of the region considered for site evaluation for a plant in order to identity hazardous phenomena associated with human induced events initiated by sources external to the plant. In some cases it also presents preliminary guidance for deriving values of relevant parameters for the design basis. This Safety Guide is also applicable for periodic site evaluation and site evaluation following a major human induced event, and for the design and operation of the site's environmental monitoring system. Site evaluation includes site characterization. Consideration of external events that could lead to a degradation of the safety features of the plant and cause a release of radioactive material from the plant and/or affect the dispersion of such material in the environment. And consideration of population issues and access issues significant to safety (such as the feasibility of evacuation, the population distribution and the location of resources). The process of site evaluation continues throughout the lifetime of the facility, from siting to design, construction, operation and decommissioning. The external human induced events considered in this Safety Guide are all of accidental origin. Considerations relating to the physical protection of the plant against wilful actions by third parties are outside its scope. However, the methods described herein may also have some application for the purposes of such physical protection. The present Safety Guide may also be used for events that may originate within the boundaries of the site, but from sources which are not directly involved in the operational states of the nuclear power plant units, such as fuel depots or areas for the storage of hazardous materials for the construction of other facilities at the same site. Special consideration should be given to the hazardous material handled during the construction, operation and

Evaluation of vibratory ground motion at nuclear power plant sites

International Nuclear Information System (INIS)

Hofmann, R.B.; Greeves, J.T.

1978-01-01

The evaluation of vibratory ground motion at nuclear power plant sites requires the cooperative effort of scientists and engineers in several disciplines. These include seismology, geology, geotechnical engineering and structural engineering. The Geosciences Branch of the NRC Division of Site Safety and Environmental Analysis includes two sections, the Geology/Seismology Section and the Geotechnical Engineering Section

Optimal Procedure for siting of Nuclear Power Plant

International Nuclear Information System (INIS)

Aziuddin, Khairiah Binti; Park, Seo Yeon; Roh, Myung Sub

2013-01-01

This study discusses on a simulation approach for sensitivity analysis of the weights of multi-criteria decision models. The simulation procedures can also be used to aid the actual decision process, particularly when the task is to select a subset of superior alternatives. This study is to identify the criteria or parameters which are sensitive to the weighting factor that can affect the results in the decision making process to determine the optimal site for nuclear power plant (NPP) site. To perform this study, we adhere to IAEA NS-R-3 and DS 433. The siting process for nuclear installation consists of site survey and site selection stages. The siting process generally consists of an investigation of a large region to select one or more candidate sites by surveying the sites. After comparing the ROI, two candidate sites are compared for final determination, which are Wolsong and Kori site. Some assumptions are taken into consideration due to limitations and constraints throughout performing this study. Sensitivity analysis of multi criteria decision models is performed in this study to determine the optimal site in the site selection stage. Logical Decisions software will be employed as a tool to perform this analysis. Logical Decisions software helps to formulate the preferences and then rank the alternatives. It provides clarification of the rankings and hence aids the decision makers on evaluating the alternatives, and finally draw a conclusion on the selection of the optimal site

Optimal Procedure for siting of Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Aziuddin, Khairiah Binti; Park, Seo Yeon; Roh, Myung Sub [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2013-10-15

This study discusses on a simulation approach for sensitivity analysis of the weights of multi-criteria decision models. The simulation procedures can also be used to aid the actual decision process, particularly when the task is to select a subset of superior alternatives. This study is to identify the criteria or parameters which are sensitive to the weighting factor that can affect the results in the decision making process to determine the optimal site for nuclear power plant (NPP) site. To perform this study, we adhere to IAEA NS-R-3 and DS 433. The siting process for nuclear installation consists of site survey and site selection stages. The siting process generally consists of an investigation of a large region to select one or more candidate sites by surveying the sites. After comparing the ROI, two candidate sites are compared for final determination, which are Wolsong and Kori site. Some assumptions are taken into consideration due to limitations and constraints throughout performing this study. Sensitivity analysis of multi criteria decision models is performed in this study to determine the optimal site in the site selection stage. Logical Decisions software will be employed as a tool to perform this analysis. Logical Decisions software helps to formulate the preferences and then rank the alternatives. It provides clarification of the rankings and hence aids the decision makers on evaluating the alternatives, and finally draw a conclusion on the selection of the optimal site.

Perryman Nuclear Power Plant. Site suitability--site safety report, volume I: chapters-sections 1.1, 1.2, 1.4, 1.6; 2.1, 2.2

International Nuclear Information System (INIS)

1977-01-01

A site suitability report is submitted in support of the Baltimore Gas and Electric Company application for a limited early site review of a potential nuclear power plant. The Perryman Nuclear Power Plant site is located in northeastern Maryland on an arm of the Chesapeake Bay estuary approximately 17 miles east--northeast of Baltimore. The proposed plant is a two-unit light water reactor with a 3800 MW(t) power level for each unit. General descriptions of the site geography, demography, nearby facilities, and meteorology are presented

Illumina amplicon sequencing of 16S rRNA tag reveals bacterial community development in the rhizosphere of apple nurseries at a replant disease site and a new planting site.

Directory of Open Access Journals (Sweden)

Jian Sun

Full Text Available We used a next-generation, Illumina-based sequencing approach to characterize the bacterial community development of apple rhizosphere soil in a replant site (RePlant and a new planting site (NewPlant in Beijing. Dwarfing apple nurseries of 'Fuji'/SH6/Pingyitiancha trees were planted in the spring of 2013. Before planting, soil from the apple rhizosphere of the replant site (ReSoil and from the new planting site (NewSoil was sampled for analysis on the Illumina MiSeq platform. In late September, the rhizosphere soil from both sites was resampled (RePlant and NewPlant. More than 16,000 valid reads were obtained for each replicate, and the community was composed of five dominant groups (Proteobacteria, Acidobacteria, Bacteroidetes, Gemmatimonadetes and Actinobacteria. The bacterial diversity decreased after apple planting. Principal component analyses revealed that the rhizosphere samples were significantly different among treatments. Apple nursery planting showed a large impact on the soil bacterial community, and the community development was significantly different between the replanted and newly planted soils. Verrucomicrobia were less abundant in RePlant soil, while Pseudomonas and Lysobacter were increased in RePlant compared with ReSoil and NewPlant. Both RePlant and ReSoil showed relatively higher invertase and cellulase activities than NewPlant and NewSoil, but only NewPlant soil showed higher urease activity, and this soil also had the higher plant growth. Our experimental results suggest that planting apple nurseries has a significant impact on soil bacterial community development at both replant and new planting sites, and planting on new site resulted in significantly higher soil urease activity and a different bacterial community composition.

Subcellular site and nature of intracellular cadmium in plants

International Nuclear Information System (INIS)

Wagner, G.J.

1979-01-01

The mechanisms underlying heavy metal accumulation, toxicity, and tolerance in higher plants are poorly understood. Since subcellular processes are undoubtedly involved in all these phenomena, it is of interest to study the extent, subcellular site and nature of intracellularly accumulated cadmium in higher plants. Whole plants supplied 109 CdCl 2 or 112 CdSO 4 accumulated Cd into roots and aerial tissues. Preparation of protoplasts from aerial tissues followed by subcellular fractionation of the protoplasts to obtain intact vacuoles, chloroplasts and cytosol revealed the presence of Cd in the cytosol but not in vacuoles or chloroplasts. No evidence was obtained for the production of volatile Cd complexes in tobacco

International Thermonuclear Experimental Reactor (ITER) plant layout and site services

International Nuclear Information System (INIS)

Chuyanov, V.

2001-01-01

The ITER site has not been determined at this time. Nevertheless, to develop a construction plan and a cost estimate, it is necessary to have a detailed layout of the buildings, structures, and outdoor equipment integrated with the balance of plant service systems prototypical of large fusion power plants. These services include electric power for magnet feeds and plasma heating systems, cryogenic and conventional cooling systems, compressed air, gas supplies, de-mineralized water, steam, and drainage. Nuclear grade facilities are provided to handle tritium fuel and activated waste, as well as to prevent radioactive exposure of either the workers or the public. To avoid interference between services of different types and for efficient arrangement of buildings, structures, and equipment within the site area, a plan was developed which segregated different classes of services to four quadrants surrounding the tokamak building, placed at the approximate geographic center of the site. Location of the twenty-seven buildings on the generic site was selected to meet all design requirements at minimum total project cost. A similar approach has been used to determine the location of services above, at, and below grade. The generic site plan can be adapted to the site selected for ITER without significant changes to the buildings or equipment. Some rearrangements may be required by site topography resulting primarily in changes to the length of services that link the buildings and equipment. (author)

International Thermonuclear Experimental Reactor (ITER) plant layout and site services

International Nuclear Information System (INIS)

Chuyanov, V.

1999-01-01

The ITER site has not been determined at this time. Nevertheless, to develop a construction plan and a cost estimate, it is necessary to have a detailed layout of the buildings, structures, and outdoor equipment integrated with the balance of plant service systems prototypical of large fusion power plants. These services include electric power for magnet feeds and plasma heating systems, cryogenic and conventional cooling systems, compressed air, gas supplies, de-mineralized water, steam, and drainage. Nuclear grade facilities are provided to handle tritium fuel and activated waste, as well as to prevent radioactive exposure of either the workers or the public. To avoid interference between services of different types and for efficient arrangement of buildings, structures, and equipment within the site area, a plan was developed which segregated different classes of services to four quadrants surrounding the tokamak building, placed at the approximate geographic center of the site. Location of the twenty-seven buildings on the generic site was selected to meet all design requirements at minimum total project cost. A similar approach has been used to determine the location of services above, at, and below grade. The generic site plan can be adapted to the site selected for ITER without significant changes to the buildings or equipment. Some rearrangements may be required by site topography resulting primarily in changes to the length of services that link the buildings and equipment. (author)

Review of Investigations on Site Selection for Nuclear Power Plants in Croatia

Energy Technology Data Exchange (ETDEWEB)

Malbasa, N [Ekonerg, Zagreb (Croatia)

2008-07-01

A review of site investigation for nuclear facilities in the Republic of Croatia that had been performed from 1964, when investigation started for the first nuclear power plant, to 1994 when the activities were stopped, is presented therein. Brief results of the main investigation were presented including the Tanja site on the Danube upstream of Vukovar. It is the best of all the investigated locations for nuclear power plant in Croatia. The review of results for site selection of low and intermediate level of radioactive waste disposal is also given. The position of nuclear power plants in the strategic documents of the Republic of Croatia was analysed. It is concluded that the status of nuclear facilities in the main strategic documents must be improved because the energy future in Croatia - as almost in all European countries - could hardly be successful without any further development of nuclear energy.(author)

Review of Investigations on Site Selection for Nuclear Power Plants in Croatia

International Nuclear Information System (INIS)

Malbasa, N.

2008-01-01

A review of site investigation for nuclear facilities in the Republic of Croatia that had been performed from 1964, when investigation started for the first nuclear power plant, to 1994 when the activities were stopped, is presented therein. Brief results of the main investigation were presented including the Tanja site on the Danube upstream of Vukovar. It is the best of all the investigated locations for nuclear power plant in Croatia. The review of results for site selection of low and intermediate level of radioactive waste disposal is also given. The position of nuclear power plants in the strategic documents of the Republic of Croatia was analysed. It is concluded that the status of nuclear facilities in the main strategic documents must be improved because the energy future in Croatia - as almost in all European countries - could hardly be successful without any further development of nuclear energy.(author)

Development of the on-site power supply in German nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Simon, M. [Gesellschaft fuer Reaktorsicherheit - GRS mbH, Schwertnergasse 1, D-5000 Koeln 1, Cologne (Germany)

1986-02-15

The design of the on-site power supply is different in German Nuclear Power Plants, depending on age and size of the plant. The cause for this is the evolution of the safety requirements. The general development of the design of safety Systems, which resulted in a strict separation of redundant trains is also reflected in the design of the emergency power system and even the complete on-site power supply System. This will be demonstrated by different examples. The advantages of this design with respect to the availability of on-site power will be explained and verified by means of operating experience. (author)

The evaluation of site characteristics for Guangdong nuclear power plant

International Nuclear Information System (INIS)

Zhou Ruming; Wu Dizhong; Yan Zhongmin

1987-01-01

This paper gives an account of the features of the site of Guangdong Nuclear Power Plant (GNPP) in general and in particular evaluates the outstanding site characteristics related to nuclear safety and public health. It is composed of two parts: the first part describes the seismo-geologic conditions of the site and the other treats the atmospheric dispersion conditions. It also contains the discussion why the possibility of inhabitancy within 5 km from the exclusion ares boundary would not be affected. (author)

Waste Isolation Pilot Plant CY 2000 Site Environmental Report

International Nuclear Information System (INIS)

Westinghouse TRU Solutions, LLC; Environmental Science and Research Foundation, Inc.

2001-01-01

The U.S. Department of Energy's (DOE) Carlsbad Field Office and Westinghouse TRU Solutions, LLC (WTS) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environmental, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2000 Site Environmental Report summarizes environmental data from calendar year (CY) 2000 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH-0173T), and the Waste Isolation Pilot Plant Environmental Protect ion Implementation Plan (DOE/WIPP 96-2199). The above orders and guidance documents require that DOE facilities submit an Annual Site Environmental Report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health. The purpose of this report is to provide a comprehensive description of operational environmental monitoring activities, to provide an abstract of environmental activities conducted to characterize site environmental management performance to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit at WIPP during CY 2000. The format of this report follows guidance offered in a June 1, 2001 memo from DOE's Office of Policy and Guidance with the subject ''Guidance for the preparation of Department of Energy (DOE) Annual Site Environmental Reports (ASERs) for Calendar Year 2000.'' WIPP received its first shipment of waste on March 26, 1999. In 2000, no evidence was found of any adverse

Waste Isolation Pilot Plant CY 2000 Site Environmental Report

Energy Technology Data Exchange (ETDEWEB)

Westinghouse TRU Solutions, LLC; Environmental Science and Research Foundation, Inc.

2001-12-31

The U.S. Department of Energy's (DOE) Carlsbad Field Office and Westinghouse TRU Solutions, LLC (WTS) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environmental, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2000 Site Environmental Report summarizes environmental data from calendar year (CY) 2000 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, the Environmental Regulatory Guide for Radiological Effluent Monitoring and Environmental Surveillance (DOE/EH-0173T), and the Waste Isolation Pilot Plant Environmental Protect ion Implementation Plan (DOE/WIPP 96-2199). The above orders and guidance documents require that DOE facilities submit an Annual Site Environmental Report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health. The purpose of this report is to provide a comprehensive description of operational environmental monitoring activities, to provide an abstract of environmental activities conducted to characterize site environmental management performance to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit at WIPP during CY 2000. The format of this report follows guidance offered in a June 1, 2001 memo from DOE's Office of Policy and Guidance with the subject ''Guidance for the preparation of Department of Energy (DOE) Annual Site Environmental Reports (ASERs) for Calendar Year 2000.'' WIPP received its first shipment of waste on March 26, 1999. In 2000, no

Site selection of a dual purpose nuclear power plant in Saudi Arabia

International Nuclear Information System (INIS)

Hussein, F.M.; Obeid, M.A.; El-Malahy, K.S.

1987-01-01

Selecting a nuclear power plant site for power production and water desalination is a very complex problem, especially in countries with moderate technology. Many interrelated factors affect the process, and professional judgments by various experts are involved. Four sites, all located on the West Coast of Saudi Arabia along the Red Sea, were chosen as potential sites for building such a plant. (All sites were in either the northern or southern section of the coast; the central part was excluded for pilgrims' safety.) The East Coast was completely eliminated in the initial screening process due to its strategic location, the existence of oil fields and refineries, and its proximity to other Arabian (Persian) Gulf countries (to minimize radioactive releases to these countries in case of an accident). A computer code based on Saaty's eigenvalue technique and developed in a previous study was used in this analysis. Twenty-one main criteria were considered, and the sites were ranked to determine which was most desirable. Site 4 was found to be most suitable, followed by site 3

Earthquakes and associated topics in relation to nuclear power plant siting

International Nuclear Information System (INIS)

1991-01-01

This Safety Guide was prepared as part of the Agency's programme for establishing Codes and Safety Guides relating to nuclear power plants. The main purpose of the text is to provide guidance on the determination of the design basis ground motions for a nuclear power plant at a chosen site and on the determination of the potential for surface faulting at that site. Additionally, the Guide discusses other permanent displacement phenomena (liquefaction, slope instability, subsidence and collapse) and introduces the topic of seismically induced flooding. Volcanic activity is not dealt with except in connection with tsunamis. 55 refs

Ames expedited site characterization demonstration at the former manufactured gas plant site, Marshalltown, Iowa

International Nuclear Information System (INIS)

Bevolo, A.J.; Kjartanson, B.H.; Wonder, J.D.

1996-03-01

The goal of the Ames Expedited Site Characterization (ESC) project is to evaluate and promote both innovative technologies (IT) and state-of-the-practice technologies (SOPT) for site characterization and monitoring. In April and May 1994, the ESC project conducted site characterization, technology comparison, and stakeholder demonstration activities at a former manufactured gas plant (FMGP) owned by Iowa Electric Services (IES) Utilities, Inc., in Marshalltown, Iowa. Three areas of technology were fielded at the Marshalltown FMGP site: geophysical, analytical and data integration. The geophysical technologies are designed to assess the subsurface geological conditions so that the location, fate and transport of the target contaminants may be assessed and forecasted. The analytical technologies/methods are designed to detect and quantify the target contaminants. The data integration technology area consists of hardware and software systems designed to integrate all the site information compiled and collected into a conceptual site model on a daily basis at the site; this conceptual model then becomes the decision-support tool. Simultaneous fielding of different methods within each of the three areas of technology provided data for direct comparison of the technologies fielded, both SOPT and IT. This document reports the results of the site characterization, technology comparison, and ESC demonstration activities associated with the Marshalltown FMGP site. 124 figs., 27 tabs

Site-specific proteolytic degradation of IgG monoclonal antibodies expressed in tobacco plants.

Science.gov (United States)

Hehle, Verena K; Lombardi, Raffaele; van Dolleweerd, Craig J; Paul, Mathew J; Di Micco, Patrizio; Morea, Veronica; Benvenuto, Eugenio; Donini, Marcello; Ma, Julian K-C

2015-02-01

Plants are promising hosts for the production of monoclonal antibodies (mAbs). However, proteolytic degradation of antibodies produced both in stable transgenic plants and using transient expression systems is still a major issue for efficient high-yield recombinant protein accumulation. In this work, we have performed a detailed study of the degradation profiles of two human IgG1 mAbs produced in plants: an anti-HIV mAb 2G12 and a tumour-targeting mAb H10. Even though they use different light chains (κ and λ, respectively), the fragmentation pattern of both antibodies was similar. The majority of Ig fragments result from proteolytic degradation, but there are only a limited number of plant proteolytic cleavage events in the immunoglobulin light and heavy chains. All of the cleavage sites identified were in the proximity of interdomain regions and occurred at each interdomain site, with the exception of the VL /CL interface in mAb H10 λ light chain. Cleavage site sequences were analysed, and residue patterns characteristic of proteolytic enzymes substrates were identified. The results of this work help to define common degradation events in plant-produced mAbs and raise the possibility of predicting antibody degradation patterns 'a priori' and designing novel stabilization strategies by site-specific mutagenesis. © 2014 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

Earthworms drive succession of both plant and Collembola communities in post-mining sites

Science.gov (United States)

Mudrák, Ondřej; Uteseny, Karoline; Frouz, Jan

2016-04-01

Previous field observations indicated that earthworms promote late-successional plant species and reduce collembolan numbers at post-mining sites in the Sokolov coal mining district (Czech Republic). Here, we established a laboratory pot experiment to test the effect of earthworms (Aporrectodea caliginosa Savigny and Lumbricus rubellus Hoffm.) and litter of low, medium, and high quality (the grass Calamagrostis epigejos, the willow Salix caprea, and the alder Alnus glutinosa, respectively) on late successional plants (grasses Arrhenatherum elatius and Agrostis capillaris, legumes Lotus corniculatus and Trifolium medium, and non-leguminous dicots Centaurea jacea and Plantago lanceolata) in spoil substrate originating from Sokolov post-mining sites and naturally inhabited by abundant numbers of Collembola. The earthworms increased plant biomass, especially that of the large-seeded A. elatius, but reduced the number of plant individuals, mainly that of the small-seeded A. capillaris and both legumes. Litter quality affected plant biomass, which was highest with S. caprea litter, but did not change the number of plant individuals. Litter quality did not modify the effect of earthworms on plants; the effect of litter quality and earthworms was only additive. Species composition of Collembola community was altered by litter quality, but earthworms reduced the number of individuals, increased the number of species, and increased species evenness consistently across the litter qualities. Because the results of this experiment were consistent with the field observations, we conclude that earthworms help drive succession of both plant and Collembola communities on post-mining sites.

75 FR 35080 - Tampa Bay Refuges, FL

Science.gov (United States)

2010-06-21

... population of gopher tortoises and box turtles. Two wildlife sanctuaries, one on the east side of the island... County. A Pinellas County seagrass sanctuary is located around Tarpon and Indian Keys, and the use of... conducting research on gopher tortoises; and identifying, mapping, and protecting State-listed plant species...

Site selection for nuclear power plants and geologic seismologia influence

International Nuclear Information System (INIS)

Castro Feitosa, G. de.

1985-01-01

The site selection for nuclear power plants is analised concerning to the process, methodology and the phases in an overall project efforts. The factors affecting are analised on a general viewpoint, showing the considerations given to every one. The geologic and seismologic factors influence on the foundation design are more detailed analised, with required investigation and procedures accordingly sub-soil conditions in the site [pt

Cooling water in the study of nuclear power plants sites

International Nuclear Information System (INIS)

Martinez, J.J.C.

1990-01-01

The location of an electric power plant has its limitations as regards the availability of apt sites. The radiosanitary risk, seismic risk and the overload capacity of the ground can be generically enumerated, being the cooling water availability for an electric power plant a basic requirement. Diverse cooling systems may be employed but the aim must always be that thermal contamination in the immediate environment be the least possible. (Author) [es

Quality assurance during site construction of nuclear power plants

International Nuclear Information System (INIS)

1981-01-01

This Safety Guide provides requirements and recommendations related to the establishment and implementation of a quality assurance programme for the site construction activities at nuclear power plants. These include activities such as fabricating, erecting, installing, handling, storing, cleaning, flushing, inspecting, testing, modifying, repairing, and maintaining

Siting Conflicts in Renewable Energy Projects in Sweden: Experiences From the Siting of a Biogas Plant

Energy Technology Data Exchange (ETDEWEB)

Khan, Jamil

2001-05-01

This paper seeks to contribute to an increased understanding of what characterises conflicts regarding the siting of renewable energy facilities. The paper starts out with a brief introduction to different types of renewable energy and the conflicts they might generate as well as a discussion about the differences and similarities in comparison with conflicts over more controversial issues, such as nuclear plants, chemical factories and the construction of roads. The main part of the paper discusses the results from a case study on a failed attempt to site a biogas plant in southern Sweden. The results show that there was a lack of public participation in the early stages of planning, and that peoples negative perceptions of the possibilities to influence the decision-making and of the attitude of the developer, contributed to the development of a public opposition and a polarisation of the conflict. There is also a discussion about the reasons for a shift in the political support for the project and about the role of the legislation in shaping planning processes that either handle conflicts or make them worse. The paper concludes with the observation that the biogas case, in many ways, resembled traditional siting conflicts and that further research is needed to explore the nature of different renewable energy siting conflicts.

Safety Considerations in the Selection of Nuclear Power Plant Candidate Sites in Johor State, Malaysia

International Nuclear Information System (INIS)

Ramli, A.T.; Basri, N.A.; Abu Hanifah, N.Z.H.

2014-01-01

Nuclear power is considered as one of the best options for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation / production, commissioning the first nuclear power plant needs tremendous effort in various aspects. The most obvious challenges are to ensure the nation’s safety and to handle security issues that may arise from a nuclear power plant site. This paper aims to propose a site for nuclear power plant in Johor State, Malaysia as well as listing the possible safety challenges in the process. The site selection uses the Malaysian Atomic Energy Licensing Board (AELB) guideline document as the main reference, supported by documents from International Atomic Energy Agency (IAEA) and from various countries. Only five site characteristics are chosen as study parameters – geological features and seismic data, air dispersion analysis using meteorological data, population distribution, safety zones and emergency supports. This paper concluded that site number 2 (CS2) at Tanjung Tenggaroh, Mersing is the most suitable area for nuclear power plant in Johor state. It has the least possible risks, safety and security issues. (author)

Safety Considerations in the Selection of Nuclear Power Plant Candidate Sites in Johor State, Malaysia

Energy Technology Data Exchange (ETDEWEB)

Ramli, A. T.; Basri, N. A.; Abu Hanifah, N. Z.H., [Department of Physics, Faculty of Science Universiti Teknologi Malaysia Johor (Malaysia)

2014-10-15

Nuclear power is considered as one of the best options for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation / production, commissioning the first nuclear power plant needs tremendous effort in various aspects. The most obvious challenges are to ensure the nation’s safety and to handle security issues that may arise from a nuclear power plant site. This paper aims to propose a site for nuclear power plant in Johor State, Malaysia as well as listing the possible safety challenges in the process. The site selection uses the Malaysian Atomic Energy Licensing Board (AELB) guideline document as the main reference, supported by documents from International Atomic Energy Agency (IAEA) and from various countries. Only five site characteristics are chosen as study parameters – geological features and seismic data, air dispersion analysis using meteorological data, population distribution, safety zones and emergency supports. This paper concluded that site number 2 (CS2) at Tanjung Tenggaroh, Mersing is the most suitable area for nuclear power plant in Johor state. It has the least possible risks, safety and security issues. (author)

Comparison of the incidence of Listeria on equipment versus environmental sites within dairy processing plants.

Science.gov (United States)

Pritchard, T J; Flanders, K J; Donnelly, C W

1995-08-01

This study was undertaken to compare the incidence of Listeria contamination of processing equipment with that of the general dairy processing environment. A total of 378 sponge samples obtained from 21 dairy plants were analyzed for Listeria using three different enrichment media. Use of extended microbiological analysis allowed us to identify 26 Listeria positive sites which would have not been identified had a single test format been employed. Eighty (80) of 378 sites (21.2%) were identified as Listeria positive. Listeria innocua was isolated from 59 of the 80 (73.8%) positive samples, L. monocytogenes was identified in 35 (43.8%) of the positive samples, and L. seeligeri was isolated from 5 (6.3%) of the Listeria positive samples. Positive equipment samples were obtained from 6 of the 21 (28.6%) plants and 19 of the 21 (90.5%) plants had positive environmental sites. Seventeen of the 215 (7.9%) samples from equipment were positive for Listeria species. Eleven of these sites, including 3 holding tanks, 2 table tops, 3 conveyor/chain systems, a pasta filata wheel, a pint milk filler and a brine pre-filter machine, were positive for L. monocytogenes. Nineteen of the 21 (90.5%) plants had positive environmental sites. Sixty-three of the 163 (41.1%) samples from environmental sites were Listeria positive and 24 were positive for L. monocytogenes. Two-tailed student t-test analysis of the mean frequencies indicated that the level of contamination was significantly higher (p plant, and that greater emphasis needs to be placed on the cleaning and sanitizing of the plant environment.

Climatology of the Savannah River Plant site

International Nuclear Information System (INIS)

Hoel, D.D.

1983-01-01

This document is intended as a reference for those involved in environmental research, and preparing environmental and safety analysis reports about aspects of operations of production and support facilities at the Savannah River Plant (SRP). The information in this document is drawn from appropriate references and from the extensive meteorological data base collected on SRP. This document contains information on the climatological characteristics of the SRP site, as well as information on relative concentrations and deposition for specific radionuclides

A method for site-dependent planning and its application to the preselection of sites for thermal power plants

International Nuclear Information System (INIS)

Friedrich, R.

1979-01-01

In the first part of the paper a computer-aided method for dealing with the problems of site-dependent planning is described. By means of the modular program system COPLAN complex conjunction between locally varying data can be performed rapidly and accurately with respect to spatial orientation. The system consists of data input, numerous ways of processing, and graphical representation of the results. The second part shows the application of the system to preselection of sites for thermal power plants. By means of a method analyzing its usefulness, the suitability of each point in (the German Federal State of) Baden-Wuerttemberg as a power plant site is determined. Compared with the currently used methods of preliminary site selection the present method is distinguished by area-covering calculation, the possibility of balancing up advantages and disadvantages, as well as transparency and suitability for being checked up. The paper establishes and considers criteria from the fields of operational economy, safety, ecology, and district planning. The computations are performed for different orders of preference. It is shown that there are regions of sites which are acceptable with respect to a large spectrum of object systems. (orig.) [de

Sites and social assessment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Nemoto, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1977-09-01

The sites of nuclear power plants in Japan have two features, first the extreme expectation for regional development because of the selection of depopulated districts for most locations, and the second, apprehensions of local people for two reasons of nuclear power generating techniques which do not plant the roots in society and handling of radioactive materials. In order to cope with these problems, it is necessary to consider that the development plan of the regions around reactor sites must be compiled systematically. Its premise is the ''social assessment'' which estimates the economical and social influences and evaluates the merit and demerit of nuclear power plants prior to the construction. This is of course inevitable. The objects of the assessment may be divided as follows: the human effect to individuals, the institutional effect to local community, the economical effect to region, and the national influence to the whole country. While the developmental action of locations includes the stages of examination, planning, construction and operation, and three location patterns are recognized according to the emphasized function, the improvement of national economy, upgrading of environmental quality, and the most priority in local welfare. In the process of the assessment, the following items may be taken notice that each item requires sometimes the weighting; the pattern to abandon location may exist; positive and negative effects are required to be distributed evenly in a triangle having the apexes each representing one of the above three patterns.

Seismic stability evaluation using 2-D FEM analysis for modeling nuclear power plants sited on gravel soil

International Nuclear Information System (INIS)

Iba, T.; Konno, T.; Irino, K.; Hama, I.; Oguro, E.; Iizuka, S.; Enami, A.

1995-01-01

Throughout Europe and the United States, many nuclear power plants have been built on Quaternary deposit sites. While in Japan, all nuclear power plants have been built at rock sites primarily to maintain a high seismic resistivity. However, as more nuclear power plants are planned for the future, it has become necessary to develop new siting technology from the stand point of expanding the available range of site selection and effective utilization of land. A draft on guidelines of the seismic design for siting on Quaternary deposits is being carried out with a purpose to ensure proper design and construction for such sites. (author). 10 figs., 2 tabs

Regulatory inspection activities on nuclear power plant sites during construction in the United Kingdom

International Nuclear Information System (INIS)

Jeffery, J.V.

1977-01-01

The work of regulatory inspection of the construction of the plant on the site is performed not only by the inspector who has been allocated to inspection duties for that site but also by the specialist staff who are involved with the safety assessment of the plant. The co-ordination of this work is described in the paper and examples are given of inspection activities associated with the enforcement requirements of licence conditions as well as those related to the inspection of the plant itself. (author)

Radiation burden of population in nuclear power plant siting

International Nuclear Information System (INIS)

Navratil, J.

The significance is discussed of the determination of the radiobiological consequences of normal operation and design basis accidents in nuclear power plant siting. The basic diagram and brief description is given of the programme for calculating the radiation load of the population in the surroundings of the nuclear power plant. The programme consists of two subprogrammes, i.e., the dispersion of radioactive gases (for normal operation and for accidents), the main programme for the determination of biological consequences and one auxiliary programme (the distribution of the population in the surroundings of the power plant). The four most important types of exposure to ionizing radiation are considered, namely inhalation, external irradiation from a cloud, ingestion (water, milk, vegetables), external irradiation from the deposit. (B.S.)

Waste Isolation Pilot Plant Site Environmental Report Calendar Year 2002

Energy Technology Data Exchange (ETDEWEB)

Washington Regulatory and Environmental Services

2003-09-17

The United States (U.S.) Department of Energy (DOE) Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environment, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2002 Site Environmental Report summarizes environmental data from calendar year 2002 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, and Guidance for the Preparation of DOE Annual Site Environmental Reports (ASERs) for Calendar Year 2002 (DOE Memorandum EH-41: Natoli:6-1336, April 4, 2003). These Orders and the guidance document require that DOE facilities submit an annual site environmental report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health; and the New Mexico Environment Department (NMED).

Waste Isolation Pilot Plant Site Environmental Report Calendar Year 2002

International Nuclear Information System (INIS)

Washington Regulatory and Environmental Services

2003-01-01

The United States (U.S.) Department of Energy (DOE) Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) are dedicated to maintaining high quality management of Waste Isolation Pilot Plant (WIPP) environmental resources. DOE Order 5400.1, General Environmental Protection Program, and DOE Order 231.1, Environment, Safety, and Health Reporting, require that the environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This Waste Isolation Pilot Plant 2002 Site Environmental Report summarizes environmental data from calendar year 2002 that characterize environmental management performance and demonstrate compliance with federal and state regulations. This report was prepared in accordance with DOE Order 5400.1, DOE Order 231.1, and Guidance for the Preparation of DOE Annual Site Environmental Reports (ASERs) for Calendar Year 2002 (DOE Memorandum EH-41: Natoli:6-1336, April 4, 2003). These Orders and the guidance document require that DOE facilities submit an annual site environmental report to DOE Headquarters, Office of the Assistant Secretary for Environment, Safety, and Health; and the New Mexico Environment Department (NMED)

Factors of site selection for nuclear power plants in selected industrial states

International Nuclear Information System (INIS)

Hoffmann, L.; Obermair, G.; Ringler, W.; Romahn, B.; Sanders, H.

1978-01-01

The range of the tasks within the project consists of working out an optimal catalogue of criteria for the site selection for nuclear power plants; establishing a structured documentation system for the criteria and licensing procedures used by selected industrial countries when selecting sites for nuclear power plants; analyzing and evaluating the documented material with the aim of supplying the basis for decisions concerning land use. The tasks are being realized within a technological ring of data (for the period until 1990, reactor types, cooling, power-heat coupling, special sites, block sizes, local concentration) and a set politico-economical ring of data for the following countries: F.R. Germany, Belgium, Switzerland, Great Britain, Sweden, Denmark, Austria, France, Netherlands, USA, Japan, Yougoslavia. (HP) [de

External main-induced events in relation to nuclear power plant siting

International Nuclear Information System (INIS)

1981-01-01

This safety Guide recomments procedures and provides information for use in implementing that part of the code of safety in Nuclear Power Plant Siting (IAEA Safety Series No. 50-C-S) which concerns man-induced events external to the plant, up to the evaluation of corresponding design basis parameters. Like the code, the Guide forms part of the IAEA's programme, referred to as the NUSS programme, for establishing codes of practice and safety Guides relating to land-based stationary thermal neutron power plants

Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Paducah Gaseous Diffusion Plant site

International Nuclear Information System (INIS)

Marmer, G.J.; Dunn, C.P.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Yuen, C.R.; Cleland, J.H.

1991-09-01

Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. The U-235 atoms are ionized when precisely tuned laser light -- of appropriate power, spectral, and temporal characteristics -- illuminates the uranium vapor and selectively photoionizes the U-235 isotope. A programmatic document for use in screening DOE site to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the PGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. 65 refs., 15 tabs

Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Paducah Gaseous Diffusion Plant site

Energy Technology Data Exchange (ETDEWEB)

Marmer, G.J.; Dunn, C.P.; Moeller, K.L.; Pfingston, J.M.; Policastro, A.J.; Yuen, C.R.; Cleland, J.H. (ed.)

1991-09-01

Uranium enrichment in the United States has utilized a diffusion process to preferentially enrich the U-235 isotope in the uranium product. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. The U-235 atoms are ionized when precisely tuned laser light -- of appropriate power, spectral, and temporal characteristics -- illuminates the uranium vapor and selectively photoionizes the U-235 isotope. A programmatic document for use in screening DOE site to locate a U-AVLIS production plant was developed and implemented in two parts. The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the PGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. 65 refs., 15 tabs.

Site selection for new nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Rizzo, Paul C.; Dubinsky, Melissa; Tastan, Erdem Onur, E-mail: paul.rizzo@rizzoassoc.com, E-mail: melissa.dubinsky@rizzoassoc.com, E-mail: onur.tastan@rizzoassoc.com [RIZZO Associates Inc., Pittsburgh, PA (United States); Miano, Sandra C., E-mail: scm27@psu.edu [Eletrobras Termonuclear S.A. (ELETRONUCLEAR), RJ (Brazil); Pennsylvania State University, Department of Mechanical and Nuclear Engineering, State College, PA (United States)

2015-07-01

The current methodology for selecting the most advantageous site(s) for nuclear power plant (NPP) development is based on the latest evolution of protocols originally established in the 1990's by the Electric Power Research Institute (EPRI) and others for programs in the USA, and more recently by the International Atomic Energy Agency (IAEA), among others. The methodology includes protocols that account for lessons learned from both the Gen III projects and the catastrophic event at Fukushima, Japan. In general, the approach requires consideration of Exclusionary or 'fatal flaw' Criteria first, based on safety as well as significant impact to the environment or human health. Sites must meet all of these Exclusionary Criteria to be considered for NPP development. Next, the remaining sites are evaluated for Avoidance Criteria that affect primarily ease of construction and operations, which allow a ranking of sites best suited for NPP development. Finally, Suitability Criteria are applied to the potential sites to better differentiate between closely ranked sites. Generally, final selection of a Preferred and an Alternate Site will require balancing of factors, expert judgment, and client input, as sites being compared will differ in their scores associated with different Avoidance Criteria and Suitability Criteria. RIZZO Associates (RIZZO) offers in this paper a modification to this methodology for selecting the site for NPP development, which accords to the categories of Exclusionary, Avoidance and Suitability Criteria strict definitions which can be considered as Absolute Factors, Critical Factors, and Economic Factors for a more focused approach to site selection. Absolute Factors include all of the safety-related Exclusionary Criteria. Critical Factors are those that are difficult to overcome unless extraordinary mitigation measures are implemented; they have a significant impact on the ability of the project to be successful and may cause the

Site selection for new nuclear power plants

International Nuclear Information System (INIS)

Rizzo, Paul C.; Dubinsky, Melissa; Tastan, Erdem Onur; Miano, Sandra C.

2015-01-01

The current methodology for selecting the most advantageous site(s) for nuclear power plant (NPP) development is based on the latest evolution of protocols originally established in the 1990's by the Electric Power Research Institute (EPRI) and others for programs in the USA, and more recently by the International Atomic Energy Agency (IAEA), among others. The methodology includes protocols that account for lessons learned from both the Gen III projects and the catastrophic event at Fukushima, Japan. In general, the approach requires consideration of Exclusionary or 'fatal flaw' Criteria first, based on safety as well as significant impact to the environment or human health. Sites must meet all of these Exclusionary Criteria to be considered for NPP development. Next, the remaining sites are evaluated for Avoidance Criteria that affect primarily ease of construction and operations, which allow a ranking of sites best suited for NPP development. Finally, Suitability Criteria are applied to the potential sites to better differentiate between closely ranked sites. Generally, final selection of a Preferred and an Alternate Site will require balancing of factors, expert judgment, and client input, as sites being compared will differ in their scores associated with different Avoidance Criteria and Suitability Criteria. RIZZO Associates (RIZZO) offers in this paper a modification to this methodology for selecting the site for NPP development, which accords to the categories of Exclusionary, Avoidance and Suitability Criteria strict definitions which can be considered as Absolute Factors, Critical Factors, and Economic Factors for a more focused approach to site selection. Absolute Factors include all of the safety-related Exclusionary Criteria. Critical Factors are those that are difficult to overcome unless extraordinary mitigation measures are implemented; they have a significant impact on the ability of the project to be successful and may cause the

The Homecourt coke plant site: a successful redeveloped brown field case

International Nuclear Information System (INIS)

Charbonnier, P.; Piguet, O.; Lereboullet, L.

2006-01-01

The environmental diagnosis of the coke plant site in Homecourt has been carried out over the last 15 years. Bail Industrie has selected two zones on the site for a remediation program in view of their further redevelopment. The weakly polluted grounds were submitted to a bio treatment, while the more polluted grounds were treated by thermal desorption. Tars have been incinerated off site. To assess the effectiveness of the treatment, percolation tests are carried out. (authors)

Adaptive Management Plan for Sensitive Plant Species on the Nevada Test Site

International Nuclear Information System (INIS)

Wills, C. A.

2001-01-01

The Nevada Test Site supports numerous plant species considered sensitive because of their past or present status under the Endangered Species Act and with federal and state agencies. In 1998, the U.S. Department of Energy, Nevada Operation Office (DOE/NV) prepared a Resource Management Plan which commits to protects and conserve these sensitive plant species and to minimize accumulative impacts to them. This document presents the procedures of a long-term adaptive management plan which is meant to ensure that these goals are met. It identifies the parameters that are measured for all sensitive plant populations during long-term monitoring and the adaptive management actions which may be taken if significant threats to these populations are detected. This plan does not, however, identify the current list of sensitive plant species know to occur on the Nevada Test Site. The current species list and progress on their monitoring is reported annually by DOE/NV in the Resource Management Plan

Environmental monitoring report, 1974

International Nuclear Information System (INIS)

1975-01-01

Results are reported of the effluent and environmental monitoring programs at the Pinellas Plant during 1974. Sample analyses revealed the on-site sewage treatment facility operated well within State of Florida Standards. Likewise, offsite discharges met the applicable standards for arsenic, biochemical oxygen demand, chlorides, chromium, copper, cyanides, detergents, dissolved oxygen, dissolved solids, fluorides, lead, mercury, nitrogen, oils and greases, phenols, pH, phosphorus, suspended solids, turbidity and zinc. The results of iron and specific conductance analyses showed levels in excess of state standards and are discussed in the body of the report. In addition to the non-radioactive parameters listed above, a small quantity of radioactive tritium oxide was released in the plant's liquid effluent. Small quantities of tritium gas, tritium oxide, and krypton-85 gas were released from the plant during the year. Average ground level concentrations of these radioisotopes were all significantly less than 1 percent of recommended guide for continuous nonoccupational exposure. (U.S.)

Plant species from coal mine overburden dumping site in Satui, South Kalimantan, Indonesia

Directory of Open Access Journals (Sweden)

Vivi Novianti

2017-07-01

Full Text Available Coal mine overburden (OB materials were nutrient-poor, loosely adhered particles of shale, stones, boulders, and cobbles, also contained elevated concentration of trace metals. This condition cause OB substrate did not support plants growth. However, there were certain species that able to grow on overburden dumping site. This investigation sought to identify plants species that presence on coal mine overburden. The research was conducted on opencast coal mine OB dumping site in Satui, South Kalimantan. Vegetation sampling was carried out on six different ages of coal mine OB dumps (7, 10, 11, 42, 59 and 64 month using line transect. Species identification used information from local people, AMDAL report of PT Arutmin Indonesia-Satui mine project, and website. There were 123 plant species, consisted of 79 herbs (Cyperaceae, Poaceae and Asteraceae, 10 lianes, bryophyte, 9 ferns, 10 shrubs, and 14 trees. A number of Poaceae, i.e., Paspalumconjugatum, Paspalumdilatatum, and Echinochloacolona generally present among the stones, boulders, and cobbles. While Cyperaceae such as Fimbristylis miliaceae, Cyperus javanicus, Rhyncospora corymbosa and Scleria sumatrensis most often foundinand around thebasin/pond with its smooth and humid substrate characteristics. Certain species of shrubs and trees present on the 7 month OB dumping site. They wereChromolaena odorata, Clibadium surinamense, Melastoma malabathricum, Trema micrantha, and Solanum torvum (Shrubs, Ochroma pyramidale and Homalanthus populifolius (trees. This plant species could be used for accelerating primary succession purpose on coal mine overburden dumping site. Nevertheless, species selection was needed to avoid planting invasive species.

Study of seismic design bases and site conditions for nuclear power plants

International Nuclear Information System (INIS)

1980-04-01

This report presents the results of an investigation of four topics pertinent to the seismic design of nuclear power plants: Design accelerations by regions of the continental United States; review and compilation of design-basis seismic levels and soil conditions for existing nuclear power plants; regional distribution of shear wave velocity of foundation materials at nuclear power plant sites; and technical review of surface-founded seismic analysis versus embedded approaches

Study of seismic design bases and site conditions for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

1980-04-01

This report presents the results of an investigation of four topics pertinent to the seismic design of nuclear power plants: Design accelerations by regions of the continental United States; review and compilation of design-basis seismic levels and soil conditions for existing nuclear power plants; regional distribution of shear wave velocity of foundation materials at nuclear power plant sites; and technical review of surface-founded seismic analysis versus embedded approaches.

Subcellular site and nature of intracellular cadmium in plants

International Nuclear Information System (INIS)

Wagner, G.J.

1979-01-01

The mechanisms underlying heavy metal accumulation, toxicity and tolerance in higher plants are poorly understood. Since subcellular processes are undoubtedly involved in all these phenomena, it is of interest to study the extent of, subcellular site of and nature of intracellularly accumulated cadmium in higher plants. Whole plants supplied 109 CdCl 2 or 112 CdSO 4 accumulated Cd into roots and aerial tissues. Preparation of protoplasts from aerial tissue followed by subcellular fractionation of the protoplasts to obtain intact vacuoles, chloroplasts and cytosol revealed the presence of Cd in the cytosol but not in vacuoles or chloroplasts. Particulate materials containing other cell components were also labeled. Of the 109 Cd supplied to plants, 2 to 10% was recovered in both cytosol preparations and in particulate materials. Cytosol contained proteinaceous--Cd complexes, free metal and low molecular weight Cd complexes. Labeling of protoplasts gave similar results. No evidence was obtained for the production of volatile Cd complexes in tobacco

Habitat types on the Hanford Site: Wildlife and plant species of concern

Energy Technology Data Exchange (ETDEWEB)

Downs, J.L.; Rickard, W.H.; Brandt, C.A. [and others

1993-12-01

The objective of this report is to provide a comprehensive source of the best available information on Hanford Site sensitive and critical habitats and plants and animals of importance or special status. In this report, sensitive habitats include areas known to be used by threatened, endangered, or sensitive plant or animal species, wetlands, preserves and refuges, and other sensitive habitats outlined in the Hanford Site Baseline Risk Assessment Methodology. Potentially important species for risk assessment and species of special concern with regard to their status as threatened, endangered, or sensitive are described, and potential habitats for these species identified.

Selection of sites for nuclear power plants in The Netherlands. Pt. B

International Nuclear Information System (INIS)

1986-01-01

In this report the headlines are presented of the participation of the Dutch people in the policy resolution with regard to the selection of sites of nuclear power plants. In Ch. 1 it is indicated how this participation is organized and the quantitative results are given. In the other chapters the results of the people's participation are treated qualitatively with restriction to the headlines. In Ch. 3 the remarks about the procedure and its precedents are reported. Ch. 4 reflects the public opinion with regard to the (nuclear) energy problem. In Ch. 5 finally the problems concerning the sites of nuclear power plants are treated. The criteria are discussed used by the participants in the judgement of the locations on their aptitude, in general as well as by possible site. (Auth.)

Siting of nuclear desalination plants in Saudi Arabia: A seismic study

International Nuclear Information System (INIS)

Aljohani, M.S.; Abdul-Fattah, A.F.; Almarshad, A.I.

2005-01-01

This paper presents the selection criteria generally and seismic criteria specifically to select a suitable site in Saudi Arabia for a nuclear desalination plant. These criteria include geological, meteorological, cooling water supply discharge, transport infrastructure, population, electric grid, water network capacity, environmental impact and airport movement. The seismicity of the Arabian peninsula for the locations of seismic activity along the Red Sea and the Arabian Gulf coastlines from 1973 to 2000 was studied carefully. This study included towns and locations along the east and west coastlines and their distances from the seismic event site. The results showed that Rabigh City along the west coast of Saudi Arabia is a good site to build a nuclear desalination plant. This is because of the following reasons: good seismic stability; good weather statistics; no flooding; mild wave conditions; good supply and discharge; good transportation infrastructure; low population area; very close to the huge electric grid. (author)

Site and feasibility studies of a first nuclear power plant in Morocco

International Nuclear Information System (INIS)

Righi, M.

1988-11-01

Basing on the estimated studies related to the evaluation of future needs of electrical energy, the launching of a nuclear power program in Morocco is confirmed necessary. A complete study of sites and feasibility has been carried out. Taking into account the site selection factors two sites: BIR ELHAR and SIDI BOULBRA have been kept as candidate sites. The evaluation of seismic and geotechnical risks of the power plant impact on the environment and risks related to human activities has led to privilege the SIDI BOULBRA site. The studies for confirming this site are summarized. 4 figs. (F.M.)

Demographic survey around proposed nuclear power plant site in Haryana covering 30 km radius area from the site

International Nuclear Information System (INIS)

Garg, V.K.

2013-01-01

This study was planned to have a demographic survey of the households living within 30 km radius of the proposed site. Objectives of the present study were to attain the quantitative baseline demographic data around (within 30 km radius) the proposed site of nuclear power plant, zone-wise and sector-wise distribution of the population around proposed site up to a distance of 30 km from the site, to obtain the data on socio-economic, cultural, and religious perspectives of the target populations, to obtain the data on disease/illness pattern in the target population, health status and mortality rate

Brazilian nuclear power plants decommissioning plan for a multiple reactor site

Energy Technology Data Exchange (ETDEWEB)

Monteiro, Deiglys B.; Moreira, Joao M.L.; Maiorino, Jose R., E-mail: deiglys.monteiro@ufabc.edu.br, E-mail: joao.moreira@ufabc.edu.br, E-mail: joserubens.maiorino@ufabc.edu.br [Universidade Federal do ABC (CECS/UFABC), Santo Andre, SP (Brazil). Centro de Engenharia, Modelagem e Ciencias Aplicadas. Programa de Pos-Graduacao em Energia e Engenharia da Energia

2015-07-01

Actually, Brazil has two operating Nuclear Power Plants and a third one under construction, all at Central Nuclear Almirante Alvaro Alberto - CNAAA. To comply with regulatory aspects the power plants operator, Eletronuclear, must present to Brazilian Nuclear Regulatory Agency, CNEN, a decommissioning plan. Brazilian experience with decommissioning is limited because none of any nuclear reactor at the country was decommissioned. In literature, decommissioning process is well described despite few nuclear power reactors have been decommissioned around the world. Some different approach is desirable for multiple reactors sites, case of CNAAA site. During the decommissioning, a great amount of wastes will be produced and have to be properly managed. Particularly, the construction of Auxiliary Services on the site could be a good choice due to the possibility of reducing costs. The present work intends to present to the Eletronuclear some aspects of the decommissioning concept and decommissioning management, storage and disposal de wastes, based on the available literature, regulatory standards of CNEN and international experience as well as to suggest some solutions to be implemented at CNAAA site before starts the decommissioning project in order to maximize the benefits. (author)

Brazilian nuclear power plants decommissioning plan for a multiple reactor site

International Nuclear Information System (INIS)

Monteiro, Deiglys B.; Moreira, Joao M.L.; Maiorino, Jose R.

2015-01-01

Actually, Brazil has two operating Nuclear Power Plants and a third one under construction, all at Central Nuclear Almirante Alvaro Alberto - CNAAA. To comply with regulatory aspects the power plants operator, Eletronuclear, must present to Brazilian Nuclear Regulatory Agency, CNEN, a decommissioning plan. Brazilian experience with decommissioning is limited because none of any nuclear reactor at the country was decommissioned. In literature, decommissioning process is well described despite few nuclear power reactors have been decommissioned around the world. Some different approach is desirable for multiple reactors sites, case of CNAAA site. During the decommissioning, a great amount of wastes will be produced and have to be properly managed. Particularly, the construction of Auxiliary Services on the site could be a good choice due to the possibility of reducing costs. The present work intends to present to the Eletronuclear some aspects of the decommissioning concept and decommissioning management, storage and disposal de wastes, based on the available literature, regulatory standards of CNEN and international experience as well as to suggest some solutions to be implemented at CNAAA site before starts the decommissioning project in order to maximize the benefits. (author)

CHEMISTRY OF PLANTS AND RECLAIMED GROUNDS ON SODA WASTE SITE AT JANIKOWO

Directory of Open Access Journals (Sweden)

Jan Siuta

2014-10-01

Full Text Available The paper presents the state of soda waste dumping site prior to reclamation, including the initial vegetation and properties of local grounds, the chemistry of plants colonizing the alkaline grounds in 2013 as well as the comparison of mineral element contents in leaves of trees spontaneously growing on the soda waste site in the years 2000 and 2013. The paper consists an integral part of a wider work concerning the effectiveness of sewage sludge application for bioremediation of highly saline and alkaline waste at the Janikowo Soda Plant. The spontaneous vegetation on soda waste in 2000 was scarce and patchy, its development conditioned by local microrelief where depressions provided water for plant establishment. The main species entering the site included grasses (Lolium perenne, Calamagrostis epigeios and herbs (Reseda lutea, Tussilago farfara and Picris hieracioides. The physico-chemical properties of waste grounds varied widely both horizontally and spatially. In 2013, the reclaimed dumping site was covered by a well-established meadow-likevegetation and the soil top layer (0–5 cm contained 9.2–13.9% Ca and 15–161 mg Cl/kg, at pH 7.6–7.8. The underlying 10–20 cm layer contained 21.1–63.3% Ca and 204–3110 mg Cl/kg, at pH 7.93–9.04. In the deeper 40-60 cm layer there was found 30.0-37.5% Ca and 9 920-16 320 mg Cl/kg, at pH 11.5–12.1. The vegetation growing in the vicinity of soil profiles contained: 1.65–3.36% N; 0.25–0.43% P; 1.38–2.95% K; 0.33–1.10 % Ca and 0.13–0.54% Mg. The contents of heavy metals in plants approximated the average amounts found in meadow clippings in Poland. The contents of main nutrients in leaves of trees spontaneously growing on the waste site were significantly higher in 2013 (2.70–3.21% N; 0.25–0.34% P and 0.98–1.75% K than in the year 2000 (1.70–2.04% N; 0.11–0.21% P and 0.54–0.80% K. The application of sewage sludge and subsequent fertilization of vegetation on waste

Collection and evaluation of complete and partial losses of off-site power at nuclear power plants

International Nuclear Information System (INIS)

Battle, R.E.

1985-02-01

Events involving loss of off-site power that have occurred at nuclear power plants through 1983 are described and categorized as complete or partial losses. The events were identified as plant-centered or grid-related failures. In addition, the causes of the failures were classified as weather, human error, design error, or hardware failure. The plant-centered failures were usually of shorter duration than the weather-related grid failures. For this reason, the weather-related events were reviewed in detail. Design features that may be important factors affecting off-site power system reliability were tabulated for most of the operating nuclear power plants. The tabulated information was provided to NRC for a statistical analysis to determine the importance of these design features for losses of off-site power. The frequency of losses of off-site power versus duration was estimated for three time periods. The frequency of loss of off-site power was estimated to be 0.09/reactor-year based on industry-wide data for the years 1959 through 1983

Remote sensing for nuclear power plant siting

International Nuclear Information System (INIS)

Siegal, B.S.; Welby, C.W.

1981-01-01

Remote sensing techniques enhance the selection and evaluation process for nuclear power plant siting. The principal advantage is the synoptic view which improves recognition of linear features, possibly indicative of faults. The interpretation of such images, in conjunction with seismological studies, also permits delineation of seismo-tectonic provinces. In volcanic terrains, geomorphic-age boundaries can be delineated and volcanic centers identified, providing necessary guidance for field sampling and regional model derivation. The use of such techniques is considered for studies in the Philippines, Mexico, and Greece. 5 refs

Proposed plan for remedial action at the chemical plant area of the Weldon Spring site

International Nuclear Information System (INIS)

1992-11-01

This proposed plan addresses the management of contaminated material at the chemical plant area of the Weldon Spring site and nearby properties in St. Charles County, Missouri. The site consists of a chemical plant area and a noncontiguous limestone quarry, both of which are radioactively and chemically contaminated as a result of past processing and disposal activities. Explosives were produced at the chemical plant in the 1940s, and uranium and thorium materials were processed in the 1950s and 1960s. Various liquid, sludge, and solid wastes were disposed of at the Chemical plant area and in the quarry during that time. The Weldon Spring site is listed on the National Priorities List (NPL) of the US Environmental Protection Agency (EPA), and the US Department of Energy (DOE) is conducting cleanup activities at the site under its Environmental Restoration and Waste Management Program. The proposed plan is organized as follows: Chapter 2 presents the history and setting of the Weldon Spring site and briefly describes the contaminated material at the chemical plant area. Chapter 3 defines the scope of the remedial action and its role in the Weldon Spring Site Remedial Action Project. Chapter 4 summarizes the risks associated with possible exposures to site contaminants in the absence of remedial action and identifies proposed cleanup levels for soil. Chapter 5 briefly describes the final alternatives considered for the remedial action. Chapter 6 summarizes the evaluation of final alternatives for managing the contaminated material, identifies the currently preferred alternative, and discusses a possible contingency remedy to provide treatment flexibility. Chapter 7 presents the community's role in this action. Chapter 8 is a list of the references cited in this proposed plan

The Role of Tectonic and Seismicity in Siting of Nuclear Power Plant

International Nuclear Information System (INIS)

Abdel Aziz, M.A.H.

2008-01-01

The site selection for the a nuclear power plant (NPP) is controlled by many criteria. One of the most important criterion is the tectonic and seismicity of the site and its surroundings. Since, it is preferable the site in concern is characterized by low tectonic and low seismicity to avoid the damage effects associated with the occurrence of destructive earthquakes. The investigation of the tectonic and seismicity maps of egypt has been carried out to candidate potential areas or sites for nuclear power plant installation from seismicity point of view. Also, the design basis ground motion in terms of peak ground acceleration and response spectra of some of the potential sites are defined through the conduct of probabilistic seismic hazard analysis The study revealed that although there is no criterion to exclude areas of high tectonic and high seismicity as potential sites for nuclear power plant installation but, it is preferable avoiding such areas. This is attributed to the critical seismic curve that characterizes such areas and is required high seismic design levels to resist the destructive vibratory ground motion associated with the expected earthquake. Consequently, the required high seismic design levels will have a negative impact on the economic cost of the facility compared with that built in low and moderate seismic areas. Hence, areas like the gulf of suez, the northern part of the Red Sea and the southern part of Sinai Peninsula should be avoided as potential sites for NPP from the tectonic and seismicity point of view. On the other hand, areas like Nile delta and its valley, the Northern and Southern parts of Western desert and the central and southern parts of the Eastern Desert should be candidate as potential sites on condition, the other criteria meet the IAEA's regulations. Also, the seismic hazard curve of the Northwest littoral zone reflects low design basis ground motion values compared with the Nile delta region

Losses of off-site power at U.S. nuclear power plants -- through 1995. Final report

International Nuclear Information System (INIS)

Wyckoff, H.

1996-04-01

This report provides a database and summary analysis of losses of off-site power at US nuclear generating units. It includes the 16 years 1980 through 1995. This is the twelfth update of this database and analysis. During 1994 there were no losses of all off-site power and in 1995 only two short losses. Both the short term and long term US loss of all off-site power experience is extremely favorable. The frequency of losing all off-site power is an important input to many nuclear plant safety assessments. The industry's loss of all off-site power experience that is set forth in this report can provide perspective to plant specific probabilistic safety assessments

Maryland Power Plant Siting Project: an application of the ORNL-Land Use Screening Procedure

International Nuclear Information System (INIS)

Dobson, J.E.

1975-01-01

Since 1974 the Resource Analysis Group in the Regional and Urban Studies Section of the Oak Ridge National Laboratory (ORNL) has been engaged in developing a procedure for regional and local siting analysis known as the ORNL Land Use Screening Procedure (LUSP). This document is the final report of the Maryland Power Plant Siting Project (MPPSP) in which the ORNL LUSP was used to identify candidate areas for power plant sites in northern Maryland. Numerous candidate areas are identified on the basis of four different siting objectives: the minimization of adverse ecologic impact, the minimization of adverse socioeconomic impact, the minimization of construction and operating costs, and a composite of all siting objectives. Siting criteria have been defined for each of these objectives through group processing techniques administered to four different groups of siting specialists. The siting priorities and opinions of each group have been expressed quantitatively and applied to a geographic information system containing 52 variables for each 91.8-acre cell in the northern eight counties of Maryland

Maryland Power Plant Siting Project: an application of the ORNL-Land Use Screening Procedure

Energy Technology Data Exchange (ETDEWEB)

Dobson, J.E.

1975-01-01

Since 1974 the Resource Analysis Group in the Regional and Urban Studies Section of the Oak Ridge National Laboratory (ORNL) has been engaged in developing a procedure for regional and local siting analysis known as the ORNL Land Use Screening Procedure (LUSP). This document is the final report of the Maryland Power Plant Siting Project (MPPSP) in which the ORNL LUSP was used to identify candidate areas for power plant sites in northern Maryland. Numerous candidate areas are identified on the basis of four different siting objectives: the minimization of adverse ecologic impact, the minimization of adverse socioeconomic impact, the minimization of construction and operating costs, and a composite of all siting objectives. Siting criteria have been defined for each of these objectives through group processing techniques administered to four different groups of siting specialists. The siting priorities and opinions of each group have been expressed quantitatively and applied to a geographic information system containing 52 variables for each 91.8-acre cell in the northern eight counties of Maryland.

Effects of Mechanical Site Preparation on Growth of Oaks Planted on Former Agricultural Fields

Directory of Open Access Journals (Sweden)

John D. Hodges

2011-12-01

Full Text Available Mechanical site preparation is frequently proposed to alleviate problematic soil conditions when afforesting retired agricultural fields. Without management of soil problems, any seedlings planted in these areas may exhibit poor growth and survival. While mechanical site preparation methods currently employed in hardwood afforestation are proven, there is a substantial void in research comparing subsoiling, bedding, and combination plowing treatments. A total of 4,320 bare-root Nuttall oak (Quercus texana Buckley, Shumard oak (Quercus shumardii Buckley, and swamp chestnut oak (Quercus michauxii Nutt. seedlings were planted in February 2008 on three Mississippi sites. All sites were of comparable soils and received above average precipitation throughout the three-year duration of the study. Four site preparation treatments were replicated at each site, with 480 seedlings planted in each of nine replications, and a total of 1,440 seedlings per species planted across all sites. Mechanical treatments were installed using 3.1 m row centers, with treatments as follows: control, subsoiling, bedding, and combination plowing. Treatment effects on seedling height, groundline diameter (GLD, and survival were analyzed. Seedlings exhibited greater height in bedded and combination plowed areas (79.7 cm to 102.7 cm and 82.6 cm to 100.1 cm, respectively compared to subsoiled or control areas (70.4 cm to 84.6 cm and 71.4 cm to 86.9 cm, respectively. Greater GLD was observed in bedded and combination plowed areas (11.9 mm to 18.4 mm and 12.2 mm to 18.3 mm, respectively compared to subsoiled or control areas (10.2 mm to 14.6 mm and 10.5 mm to 15.6 mm, respectively. Survival was high for this study (94.%, and no differences were detected among treatments.

Should the public be encouraged to visit nuclear plant sites?

International Nuclear Information System (INIS)

Ferte, J. de la

1993-01-01

As we all know, technological progress does not only depend on the innovation capacity of scientists and engineers or the sophistication of technology, but also on public acceptance. People - today - are not only more curious about new applications of technology but also more inquiring about their potential impact on their own safety and environment. This is particularly true in the nuclear field, where the people are afraid of nuclear installations and processes unknown to them. On the contrary, the more opportunities they have to see or live near nuclear plants, the less they are inclined to reject them as a whole. The past two decades have confirmed the increasing importance of visitor centres at nuclear plant sites as a major communication tool between the nuclear industry and the public. Already today, for example, 16% of the US public and 11% of the French public have visited a nuclear power plant or its information centre. A rich experience is therefore available from existing visitor centres at nuclear power stations in most industrialised countries. Furthermore, the construction and industrial operation of new facilities in the nuclear fuel cycle presents new challenges in terms of public understanding and acceptance which are progressively taken into account. As a result, visitor centres with new communication strategies and tools are now being put in place at radioactive waste management sites and nuclear fuel cycle sites as well as near nuclear installations being dismantled. The OECD Nuclear Energy Agency (NEA) organised an international Seminar in November 1992 in Madrid (Spain) in co-operation with the Spanish Agency for the Management of Radioactive Waste (ENRESA) and the Union of Spanish Electricity Utilities (UNESA) to: 1. take stock of the experience of OECD countries in the design and operation of visitor centres; 2. assess the educational and information methods and tools used in these centres, and 3. measure their impact on public opinion and

Should the public be encouraged to visit nuclear plant sites?

Energy Technology Data Exchange (ETDEWEB)

Ferte, J de la [External Relations and Public Affairs, OECD Nuclear Energy Agency, Paris (France)

1993-07-01

As we all know, technological progress does not only depend on the innovation capacity of scientists and engineers or the sophistication of technology, but also on public acceptance. People - today - are not only more curious about new applications of technology but also more inquiring about their potential impact on their own safety and environment. This is particularly true in the nuclear field, where the people are afraid of nuclear installations and processes unknown to them. On the contrary, the more opportunities they have to see or live near nuclear plants, the less they are inclined to reject them as a whole. The past two decades have confirmed the increasing importance of visitor centres at nuclear plant sites as a major communication tool between the nuclear industry and the public. Already today, for example, 16% of the US public and 11% of the French public have visited a nuclear power plant or its information centre. A rich experience is therefore available from existing visitor centres at nuclear power stations in most industrialised countries. Furthermore, the construction and industrial operation of new facilities in the nuclear fuel cycle presents new challenges in terms of public understanding and acceptance which are progressively taken into account. As a result, visitor centres with new communication strategies and tools are now being put in place at radioactive waste management sites and nuclear fuel cycle sites as well as near nuclear installations being dismantled. The OECD Nuclear Energy Agency (NEA) organised an international Seminar in November 1992 in Madrid (Spain) in co-operation with the Spanish Agency for the Management of Radioactive Waste (ENRESA) and the Union of Spanish Electricity Utilities (UNESA) to: 1. take stock of the experience of OECD countries in the design and operation of visitor centres; 2. assess the educational and information methods and tools used in these centres, and 3. measure their impact on public opinion and

Site-specific analysis of hybrid geothermal/fossil power plants. Volume One. Roosevelt Hot Springs KGRA

Energy Technology Data Exchange (ETDEWEB)

1977-06-01

The economics of a particular hybrid plant must be evaluated with respect to a specific site. This volume focuses on the Roosevelt Hot Springs KGRA. The temperature, pressure, and flow rate data given suggests the site deserves serious consideration for a hybrid plant. Key siting considerations which must be addressed before an economic judgment can be attempted are presented as follows: the availability, quality, and cost of coal; the availability of water; and the availability of transmission. Seismological and climate factors are presented. (MHR)

A plan for safety evaluation of tsunamis at the Uljin nuclear power plant site

International Nuclear Information System (INIS)

Lee, H. K.; Lee, D. S.

1999-01-01

The sites of many nuclear and thermal power plants are located along the coast line to obtain necessary cooling water. Therefore, they are vulnerable to coastal disasters like tsunamis. The safety evaluation on tsunamis of the site of Uljin nuclear power plants was performed with the maximum potential earthquake magnitude and related fault parameters in 1986. But according to the results of recent research, the possibility was suggested that the earthquake which has bigger magnitude than was expected is likely to happen in the seismic gaps near Akita, Japan. Therefore, a plan for safety evaluation of tsunamis at the Uljin nuclear power plants was laid out

Vascular plants of the Nevada Test Site and Central-Southern Nevada: ecologic and geographic distributions

Energy Technology Data Exchange (ETDEWEB)

Beatley, J.C.

1976-01-01

The physical environment of the Nevada Test Site and surrounding area is described with regard to physiography, geology, soils, and climate. A discussion of plant associations is given for the Mojave Desert, Transition Desert, and Great Basin Desert. The vegetation of disturbed sites is discussed with regard to introduced species as well as endangered and threatened species. Collections of vascular plants were made during 1959 to 1975. The plants, belonging to 1093 taxa and 98 families are listed together with information concerning ecologic and geographic distributions. Indexes to families, genera, and species are included. (HLW)

Public regulation of site selection for nuclear power plants. Present procedures and reform proposals: an annotated bibliography

International Nuclear Information System (INIS)

Klema, E.D.; West, R.L.

1977-01-01

Part I of this bibliography contains literature which describes the process of power-plant siting as conducted by the utilities, siting procedures at the point of initiative, analytical tools employed or proposed for site assessment by enterprises in the industry, and the wide range of considerations which the utilities take into account in making site assessments. Part II contains studies and reports on the structure and process of public regulation of power plant siting: the licensing of nuclear facilities by the NRC under terms of the special Government powers in the field of nuclear energy that have evolved since World War II; the steady expansion of regulatory objectives bearing on site approval for nuclear power plants; local government, State, and other Federal agency regulation of siting; survey siting procedures in other countries; the role of regulatory delay in the long lead-time required for construction and operation of nuclear plants. Part III incudes citations on regulatory structure and practice that are unresponsive to the public interest; regulatory decision making's insufficient accessible to public scrutiny and participation; and regulatory procedures that encourage and protect inefficient practices of the regulated industries. Some legal decisions and case studies are included. Part IV, Reform Proposals, includes citations on regulatory reform and reform of siting regulations. Abstracts are provided with 157 of the citations with many more papers cited by title, author, and accession data

Fruiting of browse plants affected by pine site preparation in east Texas

Science.gov (United States)

John J. Stransky; Douglas Richardson

1977-01-01

Pine planting sites prepared by burning yielded 120 kg/ha of browse fruits the third growing season after site treatment. Control plots yielded 74, KG-bladed plots 57, and chopped plots 41 kg/ha. Blackberries, American beautyberry, sumac, Sebastian bush, muscadine grape, blueberries, and southern wax-myrtle were the principal species. Most fruit was available in summer...

Archaeological reconnaissance of a proposed site for the Waste Isolation Plant (WIPP)

International Nuclear Information System (INIS)

Nielsen, J.

1976-01-01

An archaeological reconnaissance was carried out on Sections 20, 21, 28, and 29 of T 22 S, R 31 E, Eddy County, NM, the core area of a site proposed for disposal of radioactive waste in bedded salt (the Waste Isolation Pilot Plant). This site is located in the Los Medanos area east of Carlsbad, NM. Results of the survey are presented in sections on survey techniques, geology, terrain, floristics, cultural resources, theoretical considerations, site description, and recommendations

Quantitative comparison of the nuclear power plant sites in the United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Shaw, J; Sina, A M [Queen Mary Coll., London (UK). Dept. of Nuclear Engineering

1976-01-01

A probabilistic method is described for a comparison of nuclear power plant sites in the United Kingdom, which evaluates quantitatively the sites in terms of favourability, by taking into account the real term meteorological conditions, i.e. wind direction, wind speed, and stability distributions, and also the population distribution around the cities. A 'site safety quality factor' is obtained for each site and is used to compare the favourability of each site with respect to releases of radioactivity. The quality factor corresponds to the average number of persons that would be exposed to the specified relative concentration averaged over all weather conditions. The sites compared are Berkeley, Bradwell, Dungeness, Hartlepool, Heysham, Oldbury, Sizewell, and Wylfa.

The link between off-site-emergency planning and plant-internal accident management

Energy Technology Data Exchange (ETDEWEB)

Braun, H.; Goertz, R.

1995-02-01

A variety of accident management measures has been developed and implemented in the German nuclear power plants. They constitute a fourth level of safety in the defence-in-depth concept. The containment venting system is an important example. A functioning link with well defined lines of communication between plant-internal accident management and off-site disaster emergency planning has been established.

Waste Isolation Pilot Plant Annual Site Environmental Report for 2012

Energy Technology Data Exchange (ETDEWEB)

None

2013-09-01

The purpose of the Waste Isolation Pilot Plant (WIPP) Annual Site Environmental Report for 2012 (ASER) is to provide information required by U.S. Department of Energy (DOE) Order 231.1B, Environment, Safety, and Health Reporting. Specifically, the ASER presents summary environmental data to: Characterize site environmental management performance; Summarize environmental occurrences and responses reported during the calendar year; Confirm compliance with environmental standards and requirements; Highlight significant environmental accomplishments, including progress toward the DOE Environmental Sustainability Goals made through implementation of the WIPP Environmental Management System (EMS).

Building dismantlement and site remediation at the Apollo Fuel Plant: When is technology the answer?

International Nuclear Information System (INIS)

Walton, L.

1995-01-01

The Apollo fuel plant was located in Pennsylvania on a site known to have been used continuously for stell production from before the Civil War until after World War II. Then the site became a nuclear fuel chemical processing plants. Finally it was used to convert uranium hexafluoride to various oxide fuel forms. After the fuel manufacturing operations were teminated, the processing equipment was partially decontaminated, removed, packaged and shipped to a licensed low-level radioactive waste burial site. The work was completed in 1984. In 1990 a detailed site characterization was initiated to establishe the extent of contamination and to plan the building dismantlement and soil remediation efforts. This article discusses the site characterization and remedial action at the site in the following subsections: characterization; criticality control; mobile containment; soil washing; in-process measurements; and the final outcome of the project

Wind data for wind driven plant. [site selection for optimal performance

Science.gov (United States)

Stodhart, A. H.

1973-01-01

Simple, averaged wind velocity data provide information on energy availability, facilitate generator site selection and enable appropriate operating ranges to be established for windpowered plants. They also provide a basis for the prediction of extreme wind speeds.

Applications of SLAR in nuclear power plant siting: A case history

Science.gov (United States)

Siegal, B. S.

1980-01-01

Over 10,000 square km of side-looking airborne radar (SLAR) imagery was obtained and analyzed for the siting of the first nuclear power plant in the Republic of the Philippines. The imagery was obtained using the Motorola APS/AN-94D (X-band) real aperture system as part of an overall remote sensing program to site and evaluate potential site regions. Analysis of SLAR images, in conjunction with LANDSAT, color, black and white, and thermal infrared images, provided basic information on structure, relative geochronology, stratigraphy, geomorphology, and ground water, which facilitated field operations and data synthesis.

Extraction of uranium from seawater: evaluation of uranium resources and plant siting

International Nuclear Information System (INIS)

Rodman, M.R.; Gordon, L.I.; Chen, A.C.T.

1979-02-01

This report deals with the evaluation of U.S. coastal waters as a uranium resource and with the selection of a suitable site for construction of a large-scale plant for uranium extraction. Evaluation of the resource revealed that although the concentration of uranium is quite low, about 3.3 ppB in seawater of average oceanic salinity, the amount present in the total volume of the oceans is very great, some 4.5 billion metric tons. Of this, perhaps only that uranium contained in the upper 100 meters or so of the surface well-mixed layer should be considered accessible for recovery, some 160 million tonnes. The study indicated that open ocean seawater acquired for the purpose of uranium extraction would be a more favorable resource than rivers entering the sea, cooling water of power plants, or the feed or effluent streams of existing plants producing other products such as magnesium, bromine, or potable and/or agricultural water from seawater. Various considerations led to the selection of a site for a pumped seawater coastal plant at a coastal location. Puerto Yabucoa, Puerto Rico was selected. Recommendations are given for further studies. 21 figures, 8 tables

Extraction of uranium from seawater: evaluation of uranium resources and plant siting

Energy Technology Data Exchange (ETDEWEB)

Rodman, M.R.; Gordon, L.I.; Chen, A.C.T.

1979-02-01

This report deals with the evaluation of U.S. coastal waters as a uranium resource and with the selection of a suitable site for construction of a large-scale plant for uranium extraction. Evaluation of the resource revealed that although the concentration of uranium is quite low, about 3.3 ppB in seawater of average oceanic salinity, the amount present in the total volume of the oceans is very great, some 4.5 billion metric tons. Of this, perhaps only that uranium contained in the upper 100 meters or so of the surface well-mixed layer should be considered accessible for recovery, some 160 million tonnes. The study indicated that open ocean seawater acquired for the purpose of uranium extraction would be a more favorable resource than rivers entering the sea, cooling water of power plants, or the feed or effluent streams of existing plants producing other products such as magnesium, bromine, or potable and/or agricultural water from seawater. Various considerations led to the selection of a site for a pumped seawater coastal plant at a coastal location. Puerto Yabucoa, Puerto Rico was selected. Recommendations are given for further studies. 21 figures, 8 tables.

Volcanoes and associated topics in relation to nuclear power plant siting

International Nuclear Information System (INIS)

1997-01-01

The main purpose of this report is to provide draft guidance on the criteria and methods for the evaluation of a site for a nuclear power plant with respect to the potential effects of volcanic activity which may jeopardize its safety and to elicit feedback from Member States. Different types of phenomena associated with volcanism are discussed in terms of their influence on site acceptability and on derivation of design basis parameters. This report was developed for application to new nuclear power plant sites. It does not address the issue of the re-evaluation of existing nuclear power sites to the potential effects of volcanic activity, although it contains general information and criteria useful for this purpose. The guidelines and procedures discussed in this report can appropriately be used as the basis for the safe siting and design of nuclear power plants in different volcanic environments. In this report, the description of the phenomena associated with volcanism and the collection of required data and information are separated from the criteria for hazard assessment. Thus Section 2 gives the non-specialist a general description of the different types of volcanic phenomena and Section 4 provides indication on the acquisition of the database. Section 3 outlines the general requirements to be fulfilled during site selection and evaluation. Sections 5, 6 and 7 provide guidance to perform the hazard assessment and to derive the design basis parameters. Finally, Section 8 deals with monitoring systems. As general information for the non-specialist, Annex I provides the major divisions of geological time. With the same spirit, and recognizing that a complete consensus has not been reached in the scientific community on the use and meaning of some terms, a glossary of volcanological definitions is given in Annex II, applicable only to the use of this report. Finally, Annex III provides an example of a classification of volcanoes that may be used for capability

Plant species diversity as a driver of early succession in abandoned fields: a multi-site approach.

Science.gov (United States)

Van der Putten, W H; Mortimer, S R; Hedlund, K; Van Dijk, C; Brown, V K; Lepä, J; Rodriguez-Barrueco, C; Roy, J; Diaz Len, T A; Gormsen, D; Korthals, G W; Lavorel, S; Regina, I Santa; Smilauer, P

2000-07-01

Succession is one of the most studied processes in ecology and succession theory provides strong predictability. However, few attempts have been made to influence the course of succession thereby testing the hypothesis that passing through one stage is essential before entering the next one. At each stage of succession ecosystem processes may be affected by the diversity of species present, but there is little empirical evidence showing that plant species diversity may affect succession. On ex-arable land, a major constraint of vegetation succession is the dominance of perennial early-successional (arable weed) species. Our aim was to change the initial vegetation succession by the direct sowing of later-successional plant species. The hypothesis was tested that a diverse plant species mixture would be more successful in weed suppression than species-poor mixtures. In order to provide a robust test including a wide range of environmental conditions and plant species, experiments were carried out at five sites across Europe. At each site, an identical experiment was set up, albeit that the plant species composition of the sown mixtures differed from site to site. Results of the 2-year study showed that diverse plant species mixtures were more effective at reducing the number of natural colonisers (mainly weeds from the seed bank) than the average low-diversity treatment. However, the effect of the low-diversity treatment depended on the composition of the species mixture. Thus, the effect of enhanced species diversity strongly depended on the species composition of the low-diversity treatments used for comparison. The effects of high-diversity plant species mixtures on weed suppression differed between sites. Low-productivity sites gave the weakest response to the diversity treatments. These differences among sites did not change the general pattern. The present results have implications for understanding biological invasions. It has been hypothesised that alien

Land use suitability screening for power plant sites in Maryland

International Nuclear Information System (INIS)

Dobson, J.E.

1975-01-01

Since 1974 Oak Ridge National Laboratory (ORNL) has been engaged in developing an automated procedure for land use suitability screening. The Nuclear Regulatory Commission has funded the project to aid in the selection of power plant sites in Maryland. Its purpose is to identify candidate areas from which specific candidate sites can be chosen for detailed analyses. The ORNL approach assures that certain key variables are examined empirically for every cell in the study region before candidate sites are selected. Each variable is assigned an importance weight and compatibility score based upon its effect on the economic, social, or ecologic costs associated with construction in a given cell. The weighted scores for each variable are aggregated and output as a suitability score for each cell

Study on Quaternary ground siting of nuclear power plant, (1)

International Nuclear Information System (INIS)

Kokusho, Takaji; Nishi, Koichi; Honsho, Shizumitsu

1991-01-01

A seismic stability evaluation method for a nuclear power plant to be located on a Quaternary sandy/gravelly ground is discussed herein in terms of the geological and geotechnical survey, design earthquake motion evaluation and geotechnical seismic stability analyses. The geological and geotechnical exploration tunnel in the rock-foundation siting will be difficult in the Quaternary ground siting. Boring, geophysical surveys and soil samplings will play a major role in this case. The design earthquake input spectrum for this siting is proposed so as to take account the significant effect of longer period motion on the ground stability. Equivalent and non-linear analyses demonstrate the seismic stability of the foundation ground so long as the soil density is high. (author)

On site selection of thermoelectric power plants in polluted environment

International Nuclear Information System (INIS)

Gheorghe, A.V.

1992-01-01

This paper discusses the environmental impact of combined heat-power plants. The selection of the site of these plants depends on the spatial distribution law of pollutants and their chemical interaction with environment. The solutions of a diffusion equation describing a system of chemically interacting pollutants are given and discussed. The environmental impacts are described in terms of wind and atmosphere stability, effective and built stack height and the source distance parameters. The optimal constructive solutions are judged upon the concentrations of sulfur and nitrogen oxides at the ground level which must be kept under the maximum admissible limit. (author). 8 figs

Evaluation of hyperaccumulator plant species grown in metalliferous sites in Albania

Science.gov (United States)

Babani, F.; Civici, N.; Mullaj, A.; Kongjika, E.; Ylli, A.

2007-04-01

Heavy metal contamination of soils causes serious problems to our society. A small number of interesting plant species have been identified that can grow in soils containing high levels of heavy metals, and can also accumulate these metals to high concentrations in the shoot. The heavy metal contents in root, shoot, leaves and flowers of spontaneous plants grown in metalliferous sites in Albania together with the elemental composition of the native soils were determined by X-ray fluorescence spectrometry. Efficiency of photosynthetic apparatus of analyzed ecotypes was evaluated via chlorophyll fluorescence imaging during induction kinetics. Response of plant root system to the presence of metals, the available pools of metals to plants, effect of plant biomass to phytoextraction, photosynthetic pigment metabolism and chlorophyll fluorescence signature of leaves allowed to characterize hyperaccumulator properties and to detect the variation between selected ecotypes to heavy metal accumulation.

Bird Pollinator Visitation is Equivalent in Island and Plantation Planting Designs in Tropical Forest Restoration Sites

Directory of Open Access Journals (Sweden)

Ginger M. Thurston

2013-03-01

Full Text Available Active restoration is one strategy to reverse tropical forest loss. Given the dynamic nature of climates, human populations, and other ecosystem components, the past practice of using historical reference sites as restoration targets is unlikely to result in self-sustaining ecosystems. Restoring sustainable ecological processes like pollination is a more feasible goal. We investigated how flower cover, planting design, and landscape forest cover influenced bird pollinator visits to Inga edulis trees in young restoration sites in Costa Rica. I. edulis trees were located in island plantings, where seedlings had been planted in patches, or in plantation plantings, where seedlings were planted to cover the restoration area. Sites were located in landscapes with scant (10–21% or moderate (35–76% forest cover. Trees with greater flower cover received more visits from pollinating birds; neither planting design nor landscape forest cover influenced the number of pollinator visits. Resident hummingbirds and a migratory bird species were the most frequent bird pollinators. Pollination in the early years following planting may not be as affected by details of restoration design as other ecological processes like seed dispersal. Future work to assess the quality of various pollinator species will be important in assessing this idea.

Risk-benefit evaluation of nuclear power plant siting

International Nuclear Information System (INIS)

Miettinen, J.; Savolainen, I.; Silvennoinen, P.

1976-01-01

An assessment scheme is described for the risk-benefit analyses of nuclear power versus conventional alternatives. Given the siting parameters for the proposed nuclear plant an economic comparison is made with the most advantageous competitive conventional production scenario. The economic benefit is determined from the differential discounted annual energy procurement cost as a function of the real interest rate and amortization time. The risk analysis encompasses the following factors: radiation risks in normal operation, reactor accident hazards and economic risks, atmospheric pollutants from the conventional power plants, and fuel transportation. The hazards are first considered in terms of probabilistic dose distributions. In the second stage risk components are converted to a compatible form where excess mortality is used as the risk indicator. Practical calculations are performed for the power production alternatives of Helsinki where district heat would be extracted from the nuclear power plant. At the real interest rate of 10% and amortization time of 20 yr the 1000 MW(e) nuclear option is found to be Pound9.1 m per yr more economic than the optimal conventional scenario. Simultaneously the nuclear alternative is estimated to reduce excess mortality by 2 to 5 fatal injuries annually. (author)

A Site Selection Model for a Straw-Based Power Generation Plant with CO2 Emissions

Directory of Open Access Journals (Sweden)

Hao Lv

2014-10-01

Full Text Available The decision on the location of a straw-based power generation plant has a great influence on the plant’s operation and performance. This study explores traditional theories for site selection. Using integer programming, the study optimizes the economic and carbon emission outcomes of straw-based power generation as two objectives, with the supply and demand of straw as constraints. It provides a multi-objective mixed-integer programming model to solve the site selection problem for a straw-based power generation plant. It then provides a case study to demonstrate the application of the model in the decision on the site selection for a straw-based power generation plant with a Chinese region. Finally, the paper discusses the result of the model in the context of the wider aspect of straw-based power generation.

History and stabilization of the Plutonium Finishing Plant (PFP) complex, Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Gerber, M.S., Fluor Daniel Hanford

1997-02-18

The 231-Z Isolation Building or Plutonium Metallurgy Building is located in the Hanford Site`s 200 West Area, approximately 300 yards north of the Plutonium Finishing Plant (PFP) (234-5 Building). When the Hanford Engineer Works (HEW) built it in 1944 to contain the final step for processing plutonium, it was called the Isolation Building. At that time, HEW used a bismuth phosphate radiochemical separations process to make `AT solution,` which was then dried and shipped to Los Alamos, New Mexico. (AT solution is a code name used during World War II for the final HEW product.) The process was carried out first in T Plant and the 224-T Bulk Reduction Building and B Plant and the 224-B Bulk Reduction Building. The 224-T and -B processes produced a concentrated plutonium nitrate stream, which then was sent in 8-gallon batches to the 231-Z Building for final purification. In the 231-Z Building, the plutonium nitrate solution underwent peroxide `strikes` (additions of hydrogen peroxide to further separate the plutonium from its carrier solutions), to form the AT solution. The AT solution was dried and shipped to the Los Alamos Site, where it was made into metallic plutonium and then into weapons hemispheres.` The 231-Z Building began `hot` operations (operations using radioactive materials) with regular runs of plutonium nitrate on January 16, 1945.

Anti-nuclear activities and critics concerning nuclear power plant sites

International Nuclear Information System (INIS)

Rhee, We-Beg

2000-01-01

Korea has dynamic nuclear power expansion programs, operating 16 nuclear units producing 13710 MW in total located on 4 different sites. Last year, nuclear power supplied over 40 % of national total electricity demands. In 1998, Korean government initiated re-designation work investigating circumstance changes to rule out the unnecessary sites in consideration of a long-term power supply. Korean government has determined to expand the Ulchin site and to designate one point of Woolju county as a new candidate site, and ruled out the rest candidate sites at the end of 1998. About such a governmental measure, the two areas show different reactions. Ulchin where nuclear power plant has been operated safely for about 10 years was likely to accept the governmental determination in spite of some opposition and called for several financial supports for local development. WooIju county, however, showed a strong opposition among local environmental groups and autonomous politicians, and they presented a variety of anti-nuclear activities including demonstrations mainly at the neighbouring metropolis, Ulsan city

Native Plant Uptake Model for Radioactive Waste Disposal Areas at the Nevada Test Site

Energy Technology Data Exchange (ETDEWEB)

BROWN,THERESA J.; WIRTH,SHARON

1999-09-01

This report defines and defends the basic framework, methodology, and associated input parameters for modeling plant uptake of radionuclides for use in Performance Assessment (PA) activities of Radioactive Waste Management Sites (RWMS) at the Nevada Test Site (NTS). PAs are used to help determine whether waste disposal configurations meet applicable regulatory standards for the protection of human health, the environment, or both. Plants adapted to the arid climate of the NTS are able to rapidly capture infiltrating moisture. In addition to capturing soil moisture, plant roots absorb nutrients, minerals, and heavy metals, transporting them within the plant to the above-ground biomass. In this fashion, plant uptake affects the movement of radionuclides. The plant uptake model presented reflects rooting characteristics important to plant uptake, biomass turnover rates, and the ability of plants to uptake radionuclides from the soil. Parameters are provided for modeling plant uptake and estimating surface contaminant flux due to plant uptake under both current and potential future climate conditions with increased effective soil moisture. The term ''effective moisture'' is used throughout this report to indicate the soil moisture that is available to plants and is intended to be inclusive of all the variables that control soil moisture at a site (e.g., precipitation, temperature, soil texture, and soil chemistry). Effective moisture is a concept used to simplify a number of complex, interrelated soil processes for which there are too little data to model actual plant available moisture. The PA simulates both the flux of radionuclides across the land surface and the potential dose to humans from that flux. Surface flux is modeled here as the amount of soil contamination that is transferred from the soil by roots and incorporated into aboveground biomass. Movement of contaminants to the surface is the only transport mechanism evaluated with the model

Native Plant Uptake Model for Radioactive Waste Disposal Areas at the Nevada Test Site

International Nuclear Information System (INIS)

Brown, Theresa J.; Wirth, Sharon

1999-01-01

This report defines and defends the basic framework, methodology, and associated input parameters for modeling plant uptake of radionuclides for use in Performance Assessment (PA) activities of Radioactive Waste Management Sites (RWMS) at the Nevada Test Site (NTS). PAs are used to help determine whether waste disposal configurations meet applicable regulatory standards for the protection of human health, the environment, or both. Plants adapted to the arid climate of the NTS are able to rapidly capture infiltrating moisture. In addition to capturing soil moisture, plant roots absorb nutrients, minerals, and heavy metals, transporting them within the plant to the above-ground biomass. In this fashion, plant uptake affects the movement of radionuclides. The plant uptake model presented reflects rooting characteristics important to plant uptake, biomass turnover rates, and the ability of plants to uptake radionuclides from the soil. Parameters are provided for modeling plant uptake and estimating surface contaminant flux due to plant uptake under both current and potential future climate conditions with increased effective soil moisture. The term ''effective moisture'' is used throughout this report to indicate the soil moisture that is available to plants and is intended to be inclusive of all the variables that control soil moisture at a site (e.g., precipitation, temperature, soil texture, and soil chemistry). Effective moisture is a concept used to simplify a number of complex, interrelated soil processes for which there are too little data to model actual plant available moisture. The PA simulates both the flux of radionuclides across the land surface and the potential dose to humans from that flux. Surface flux is modeled here as the amount of soil contamination that is transferred from the soil by roots and incorporated into aboveground biomass. Movement of contaminants to the surface is the only transport mechanism evaluated with the model presented here

Site selection and evaluation for nuclear power plants with respect to population distribution

International Nuclear Information System (INIS)

1980-01-01

This safety guide, relating population distribution to site selection and evaluation, for nuclear power plants, forms part of the IAEA's programme, referred to as the NUSS programme (Nuclear Safety Standards). The guide presents population distribution data, requirements, examples of site screening methods, and an overview of radiological impact assessment with respect to population distribution

Rock siting of nuclear power plants from a reactor safety standpoint. Status report October 1974

International Nuclear Information System (INIS)

1975-01-01

The aim of this study is to clearify the advantages and disadvantages of an underground nuclear power plant from a reactor safety point of view, compared to a plant above ground. Principles for the technical design of a rock sited BWR nuclear power plant is presented. Also questions of sabotage and closing down the plant at the end of the operational period are treated. (K.K.)

Test program for closure activities at a mixed waste disposal site at the Savannah River Plant

International Nuclear Information System (INIS)

Cook, J.R.; Harley, J.P. Jr.

1988-01-01

A 58-acre site at the Savannah River Plant which was used for disposal of low-level radioactive waste and quantities of the hazardous materials lead, cadmium, scintillation fluid, and oil will be the first large waste site at the Savannah River Plant to be permanently closed. The actions leading to closure of the facility will include surface stabilization and capping of the site. Test programs have been conducted to evaluate the effectiveness of dynamic compaction as a stabilization technique and the feasibility of using locally derived clay as a capping material

Evaluation of Suitability of Selected Set of Coal Plant Sites for Repowering with Small Modular Reactors

Energy Technology Data Exchange (ETDEWEB)

Belles, Randy [ORNL; Copinger, Donald A [ORNL; Mays, Gary T [ORNL; Omitaomu, Olufemi A [ORNL; Poore III, Willis P [ORNL

2013-03-01

This report summarizes the approach that ORNL developed for screening a sample set of small coal stations for possible repowering with SMRs; the methodology employed, including spatial modeling; and initial results for these sample plants. The objective in conducting this type of siting evaluation is to demonstrate the capability to characterize specific sample coal plant sites to identify any particular issues associated with repowering existing coal stations with SMRs using OR-SAGE; it is not intended to be a definitive assessment per se as to the absolute suitability of any particular site.

Power plant siting; an application of the nominal group process technique

International Nuclear Information System (INIS)

Voelker, A.H.

1976-01-01

The application of interactive group processes to the problem of facility siting is examined by this report. Much of the discussion is abstracted from experience gained in applying the Nominal Group Process Technique, an interactive group technique, to the identification and rating of factors important in siting nuclear power plants. Through this experience, interactive group process techniques are shown to facilitate the incorporation of the many diverse factors which play a role in siting. In direct contrast to mathematical optimization, commonly represented as the ultimate siting technique, the Nominal Group Process Technique described allows the incorporation of social, economic, and environmental factors and the quantification of the relative importance of these factors. The report concludes that the application of interactive group process techniques to planning and resource management will affect the consideration of social, economic, and environmental concerns and ultimately lead to more rational and credible siting decisions

15 CFR 714.1 - Annual declaration requirements for plant sites that produce a Schedule 3 chemical in excess of...

Science.gov (United States)

2010-01-01

... plant sites that produce a Schedule 3 chemical in excess of 30 metric tons. 714.1 Section 714.1 Commerce... SCHEDULE 3 CHEMICALS § 714.1 Annual declaration requirements for plant sites that produce a Schedule 3... in the production of a chemical in any units within the same plant through chemical reaction...

Perry Nuclear Plant's Plans for on-site storage

International Nuclear Information System (INIS)

Ratchen, J.T.

1993-01-01

Because of current radwaste disposal legislation and the eventual denial of access to the Barnwell, Richland, and Beatty burial sites, it was imperative for the Perry nuclear power plant to develop alternative means for handling its generated radioactive waste. The previous radwaste facilities at Perry were developed for processing, packaging, short-term storage, and shipment for burial. In order to meet the changing needs, new facilities have been constructed to handle the processing, packaging, and 5-yr interim storage of both dry active waste (DAW) and dewatered or solidified resin, filter media, etc

Care of personnel on the building site of the Dukovany nuclear power plant

International Nuclear Information System (INIS)

Kurial, P.

1984-01-01

The accommodation is described of workers on the building site of the Dukovany nuclear power plant. The quality is appraised of accommodation, catering and refreshments. There is a health care unit on site and 15 beds are reserved at the Trebic hospital for emergency cases. Trade union and youth organizations look after sports and cultural activities. (E.S.)

Characterization and remediation of a former manufactured gas plant (MGP) disposal site

International Nuclear Information System (INIS)

Murarka, I.P.; Neuhauser, E.F.; Sherman, M.W.; Taylor, B.B.; Mauro, D.M.; Ripp, J.A.; Taylor, T.D.

1993-01-01

From the early 1800s through the late 1940s, the production of gas using coal, coke or oil resulted in generation of large volumes of residues including coal tar, lamp black and wood chips containing cyanides at manufactured gas plant (MGP) sites. Often, these tarry residues were disposed of by burial at or near these plants. In recent years, old MGP sites have come under increased scrutiny from environmental regulators. To address the issues of groundwater contamination and need for clean-up, it is necessary to accurately determine where the tarry materials are now located and how different chemicals released from tars have migrated away from their sources. EPRI research at a coal-tar disposal site in New York has focused on examining and evaluating conventional and innovative methods for sampling and analysis to delineate the nature and extent of subsurface contamination, and to assess the efficacy of remedial actions. This paper presents some of the results of this research and offers recommendations on conducting size investigations as well as selecting appropriate remediation measures

Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Oak Ridge Gaseous Diffusion Plant Site

Energy Technology Data Exchange (ETDEWEB)

1991-09-01

In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) technology, with the near-term goal to provide the necessary information to make a deployment decision by November 1992. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. A programmatic document for use in screening DOE sites to locate the U-AVLIS production plant was developed and implemented in two parts (Wolsko et al. 1991). The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were then subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the ORGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use, socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3. Following the site description and additional data requirements, Sec. 4 provides a short, qualitative assessment of potential environmental issues. 37 refs., 20 figs., 18 tabs.

Environmental site description for a Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) production plant at the Oak Ridge Gaseous Diffusion Plant Site

International Nuclear Information System (INIS)

1991-09-01

In January 1990, the Secretary of Energy approved a plan for the demonstration and deployment of the Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) technology, with the near-term goal to provide the necessary information to make a deployment decision by November 1992. The U-AVLIS process is based on electrostatic extraction of photoionized U-235 atoms from an atomic vapor stream created by electron-beam vaporization of uranium metal alloy. A programmatic document for use in screening DOE sites to locate the U-AVLIS production plant was developed and implemented in two parts (Wolsko et al. 1991). The first part consisted of a series of screening analyses, based on exclusionary and other criteria, that identified a reasonable number of candidate sites. These sites were then subjected to a more rigorous and detailed comparative analysis for the purpose of developing a short list of reasonable alternative sites for later environmental examination. This environmental site description (ESD) provides a detailed description of the ORGDP site and vicinity suitable for use in an environmental impact statement (EIS). The report is based on existing literature, data collected at the site, and information collected by Argonne National Laboratory (ANL) staff during a site visit. The organization of the ESD is as follows. Topics addressed in Sec. 2 include a general site description and the disciplines of geology, water resources, biotic resources, air resources, noise, cultural resources, land use, socioeconomics, and waste management. Identification of any additional data that would be required for an EIS is presented in Sec. 3. Following the site description and additional data requirements, Sec. 4 provides a short, qualitative assessment of potential environmental issues. 37 refs., 20 figs., 18 tabs

77 FR 12002 - Mount Baker-Snoqualmie National Forest Site-Specific Invasive Plant Treatment Project and Forest...

Science.gov (United States)

2012-02-28

... Invasive Plant Treatment Project and Forest Plan Amendment Number 28 AGENCY: Forest Service, USDA. ACTION... Forest. The current Forest-wide treatment approach pre-dates the Pacific Northwest Region Invasive Plant... interdisciplinary analysis: (1) Whether or not to authorize site- specific invasive plant treatments using...

Profiling of plants at petroleum contaminated site for phytoremediation.

Science.gov (United States)

Anyasi, Raymond Oriebe; Atagana, Harrison Ifeanyichukwu

2018-03-21

The paucity of information in the literature on the characteristics of plants that could be used for phytoremediation of petroleum hydrocarbons (PHC)-contaminated sites was the principal reason for this study. The aim of the study was to identify indigenous plants growing in PHC-impacted soil in Umuahia in eastern-Nigeria that have the ability to phytoremediate soils contaminated with hydrocarbons under tropical monsoon climate conditions. A total of 28 native plant species from different families growing in and around hydrocarbon-impacted soil in the vicinity of vandalized pipelines carrying petroleum products were collected and studied for their ability to grow in a hydrocarbon-impacted soil and remove the PHC from the impacted soil. Some of the plants demonstrated the ability to grow in soil with high levels of the total petroleum hydrocarbons (TPH), which shows that they may be tolerant to hydrocarbons in soil and could potentially phytoremediate a hydrocarbon-contaminated soil. Chromolaena odorata, Aspilia africana, Chloris barbata, Pasparlum vaginatum, Bryophyllum pinnatum, Paspalum scrobiculatum, Cosmos bipinnatus, Eragrostis atrovirens, Cyperus rotundus, and Uvaria chamae showed tendencies to phytoremediate contaminated soil. By using bioaccumulation coefficient (BAC) as a measure of phytoremediation, results showed that C. odorata, A. africana, and U. chamae demonstrated the highest potentials to phytodegrade hydrocarbons in soil.

Technology overview: assessment of social values in thermal power plant siting, social impact methodology evaluation

International Nuclear Information System (INIS)

Anon.

1978-01-01

A methodology was developed to facilitate the selection of favorable thermal power plant site and design alternatives from the community perspective. A two-stage, multicriteria decision technique was employed to combine technical assessments of effects of the proposed site/design alternatives with corresponding community values. In the first stage, submodels are used to develop indices of plant impact on each of ten decision criteria. These criteria include effects on aesthetics, water quality, cost of power, air quality, ecology, social quality, local economy, recreational opportunities, cultural resources, and human health and safety. In the second stage, each of the impact indices is weighted by corresponding community values and then summed to provide an overall index of plant acceptability

In situ bioremediation (natural attenuation) at a gas plant waste site

International Nuclear Information System (INIS)

Ginn, J.S.; Sims, R.C.

1995-01-01

A former manufactured gas plant (MGP) waste site in New York was evaluated with regard to natural attenuation of polycyclic aromatic hydrocarbons (PAHs). Parent-compound concentrations of PAHs within an aquifer plume were observed to decrease with time subsequent to source removal of coal tar. Biotransformation-potential studies indicated that indigenous microorganisms in soil from the site were capable of degrading naphthalene and phenanthrene. A biochemical metabolite of phenanthrene degradation, 1-hydroxy-2-naphthoic acid (1H2NA), was tentatively characterized in coal-tar-contaminated soil from the site-based on liquid chromatographic retention time. Kinetic information was developed for the disappearance of phenanthrene and 1H2NA in nonspiked contaminated soil at the site. The Microtox trademark bioassay was used to evaluate toxicity trends in contaminated soil at the site. Results from the Microtox trademark indicated a decreasing trend in toxicity with respect to time in contaminated site soil. Research results were evaluated with regard to the National Research Council's guidelines for evaluating in situ bioremediation, and were used to enhance site characterization and monitoring information for evaluating the role of bioremediation as part of natural attenuation of PAHs at coal-tar-contaminated sites

Hydrosphere monitoring at nuclear power plant sites

International Nuclear Information System (INIS)

Belousova, A.P.; Zakharova, T.V.; Shvets, V.M.

1993-01-01

The paper deals with problems related to protection of the environment in areas occupied by nuclear power plants (NPP). NPP construction and operation result in destruction of ecological, geochemical and geological equilibria in and around NPP sites. This process requires monitoring. Recommendations of the International Agency for Atomic Energy (IAAE) suggest monitoring to commence 2-3 years prior to the start of NPP construction. The paper describes the extent of hydrosphere monitoring and guidelines along which monitoring is to be organized. The authors recommend a certain approach toward the planning observation networks and provide description of forecasting subsystem that consist of a data bank, a continuously operating model (COM) and a forecast unit

Biological fluidized-bed treatment of groundwater from a manufactured gas plant site

International Nuclear Information System (INIS)

Grey, G.M.; Scheible, O.K.; Maiello, J.A.; Guarini, W.J.; Sutton, P.M.

1995-01-01

Bench- and pilot-scale biological treatability studies were performed as part of a comprehensive study for developing an on-site treatment system for contaminated groundwater at a former manufactured gas plant site. The bench-scale work, which included evaluations of activated sludge and fluidized-bed biological processes, indicated that a carbon-based fluidized-bed process was most appropriate. The process was then demonstrated on a pilot level at the site. The bench and pilot studies demonstrated significant reductions of chemical oxygen demand (COD), and all target organics including polycyclic aromatic hydrocarbons (PAHs) and volatile organic compounds (VOCs)

Waste Isolation Pilot Plant Annual Site Environmental Report for 2014. Emended

International Nuclear Information System (INIS)

2015-01-01

The purpose of the Waste Isolation Pilot Plant (WIPP) Annual Site Environmental Report for 2014 (ASER) is to provide information required by U.S. Department of Energy (DOE) Order 231.1B, Environment, Safety, and Health Reporting. Specifically, the ASER presents summary environmental data to: Characterize site environmental management performance; Summarize environmental occurrences and responses reported during the calendar year (CY); Confirm compliance with environmental standards and requirements; Highlight significant environmental accomplishments, including progress toward the DOE environmental sustainability goals made through implementation of the WIPP Environmental Management System (EMS).

Waste Isolation Pilot Plant Annual Site Environmental Report for 2014. Emended

Energy Technology Data Exchange (ETDEWEB)

none,

2015-09-01

The purpose of the Waste Isolation Pilot Plant (WIPP) Annual Site Environmental Report for 2014 (ASER) is to provide information required by U.S. Department of Energy (DOE) Order 231.1B, Environment, Safety, and Health Reporting. Specifically, the ASER presents summary environmental data to: Characterize site environmental management performance; Summarize environmental occurrences and responses reported during the calendar year (CY); Confirm compliance with environmental standards and requirements; Highlight significant environmental accomplishments, including progress toward the DOE environmental sustainability goals made through implementation of the WIPP Environmental Management System (EMS).

Geologic CO₂ Sequestration Potential of 42 California Power Plant Sites: A Status Report to WESTCARB

Energy Technology Data Exchange (ETDEWEB)

Myers, Katherine B.L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wagoner, J. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-06-15

Forty-two California natural gas combined-cycle (NGCC) power plant sites were evaluated for geologic carbon dioxide (CO₂) sequestration potential. The following data were collected in order to gauge the sequestration potential of each power plant site: nearest potential CO₂ sink, proximity to oil or gas fi elds, subsurface geology, surface expression of nearby faults, and subsurface water. The data for each site were compiled into a one-page, standalone profi le to serve as a quick reference for future decision-makers. A subset of these data was compiled into a summary table for easy comparison of all 42 sites. Decision-makers will consider the geologic CO₂ sequestration potential of each power plant in concert with its CO₂ capture potential and will select the most suitable sites for a future carbon capture and storage project. Once the most promising sites are selected, Lawrence Livermore National Laboratory (LLNL) will conduct additional geologic research in order to construct a detailed 3D geologic model for those sites.

Plant/soil concentration ratios of 226Ra for contrasting sites around an active U mine-mill

International Nuclear Information System (INIS)

Ibrahim, S.A.; Whicker, F.W.

1988-01-01

Concentrations of 226Ra were determined in native vegetation and underlying substrate (soil and tailings) at various sites around a conventional open-pit, acid leach U production operation in Wyoming. Plant/soil concentration ratios (CRs) for 226Ra were estimated for various sites, including weathered tailings; a tailings impoundment shoreline; downwind from exposed tailings; a mine overburden reclamation area; and several background locations. Radium-226 concentrations for vegetation and substrate and CR values from the perturbed sites were elevated above background. The highest vegetation concentration (1.3 Bq g-1) was found in a grass which had invaded exposed, weathered tailings. Levels of 226Ra in soil and vegetation and CR values decreased with distance from the tailings impoundment edge. CR values varied significantly among sites, but few differences were found between plant species groups. The observed CR values ranged from 0.07 at the background and reclamation areas to 0.4 downwind from the tailings area. Average CR values for plants growing on exposed tailings and within one meter from the impoundment edge were 0.15 and 0.3, respectively. CR values of 226Ra for plants on tailings substrates were comparatively low in contrast to other radionuclides in the U chain. We speculate that in the case of sulfuric acid leached tailings-derived material, 226Ra is sequestered as sulfate, which is highly insoluble relative to the sulfates of the other elements (e.g., U and Th) resulting in reduced availability for plant uptake

A plant taxonomic survey of the Uranium City region, Lake Athabasca north shore, emphasizing the naturally colonizing plants on uranium mine and mill wastes and other human-disturbed sites

International Nuclear Information System (INIS)

Harms, V.L.

1982-07-01

A goal of this study was to acquire more complete baseline data on the existing flora of the Uranium City region, both in natural and human-disturbed sites. Emphasis was given to determining which plant species were naturally revegetating various abandoned uranium mine and mill waste disposal areas, other human-disturbed sites, and ecologically analogous sites. Another goal was to document the occurrence and distribution in the study region of rare and possibly endangered species. A further objective was to suggest regionally-occurring species with potential value for revegetating uranium mine and mill waste sites. Field investigations were carried out in the Uranium City region during August, 1981. During this time 1412 plant collections were made; a total of 366 plant species - trees, shrubs, forbs, graminoids, lichens, and bryophytes were recorded. The report includes an annotated checklist of plant species of the Uranium City region and a reference index of plant taxa indicating species that have high revegetation potential

Energy benchmarking in wastewater treatment plants: the importance of site operation and layout.

Science.gov (United States)

Belloir, C; Stanford, C; Soares, A

2015-01-01

Energy benchmarking is a powerful tool in the optimization of wastewater treatment plants (WWTPs) in helping to reduce costs and greenhouse gas emissions. Traditionally, energy benchmarking methods focused solely on reporting electricity consumption, however, recent developments in this area have led to the inclusion of other types of energy, including electrical, manual, chemical and mechanical consumptions that can be expressed in kWh/m3. In this study, two full-scale WWTPs were benchmarked, both incorporated preliminary, secondary (oxidation ditch) and tertiary treatment processes, Site 1 also had an additional primary treatment step. The results indicated that Site 1 required 2.32 kWh/m3 against 0.98 kWh/m3 for Site 2. Aeration presented the highest energy consumption for both sites with 2.08 kWh/m3 required for Site 1 and 0.91 kWh/m3 in Site 2. The mechanical energy represented the second biggest consumption for Site 1 (9%, 0.212 kWh/m3) and chemical input was significant in Site 2 (4.1%, 0.026 kWh/m3). The analysis of the results indicated that Site 2 could be optimized by constructing a primary settling tank that would reduce the biochemical oxygen demand, total suspended solids and NH4 loads to the oxidation ditch by 55%, 75% and 12%, respectively, and at the same time reduce the aeration requirements by 49%. This study demonstrated that the effectiveness of the energy benchmarking exercise in identifying the highest energy-consuming assets, nevertheless it points out the need to develop a holistic overview of the WWTP and the need to include parameters such as effluent quality, site operation and plant layout to allow adequate benchmarking.

Siting locally-unwanted facilities: What can be learnt from the location of Italian power plants

International Nuclear Information System (INIS)

Garrone, Paola; Groppi, Angelamaria

2012-01-01

The reaction of communities to the development of energy facilities is based on the environmental impact of the investment, but it also reflects the ex-ante propensity of residents to engage in collective actions. In this work we have examined the requests of authorization of Italian power producers for new thermal plants with the purpose of testing the efficiency of market-based siting policies. The classical location factors, e.g., infrastructure availability, have been confirmed to play a role, and there is a weak evidence that authorization demands have targeted communities that suffer less environmental damage. However our findings have also revealed that power producers are likely to avoid potentially suitable sites if they host a highly activistic community. The paper also discusses some modifications concerning siting policies that could improve the alignment between community responses and the environmental costs of new energy facilities. - Highlights: ► We model location choices for polluting power plants by Italian producers in 1999–2006. ► The efficiency of market-based siting policies is tested (i.e., plants located where environmental damage is lower). ► More than environmental costs, voice factors prevailed on the location choices. ► We conclude that market-based siting policies does not ensure an efficient outcome. ► Developers and communities relationship may suffer from relevant transaction costs

Soil remediation of a former power plant site in Tulita, Northwest Territories

International Nuclear Information System (INIS)

Pouliot, Y.; Thomassin-Lacroix, E.; Moreau, N.

2005-01-01

This paper outlines major stages of an ongoing remediation project caused by a power generating plant in the Dene Hamlet of Tulita. High levels of soil contamination were caused by the plant's operations as well as accidental petroleum hydrocarbon (PHC) spills. The decommissioning of the plant required that the site be remediated. Challenges faced by the remediators included the high level of contamination, the remote location of the community, as well as the fact that the site was located in the centre of the community. In addition, the soil in the impacted site was fine, and a 20 cm thick layer of peat acted as sponge, absorbing and trapping hydrocarbons. Remedial criteria was outlined according to Canada-Wide Standards for fine-grained soil in an industrial setting. The technology used for the project was Biopile, a process consisting of installing wells in the contaminated zone in order to provide the aeration required for PHC biodegradation and to condition the soil on a regular basis in order to promote optimal treatment conditions throughout the impacted material. Results indicated that the first 2 months were successful in reducing initial PHC levels. However, the following treatment season did not show as much degradation. An investigation revealed that nitrogen and phosphorus levels were insufficient to sustain microbial activity, as a result of lower than normal temperatures in the area for that season. Nutrients were added to the soil to re-establish the appropriate treatment conditions. It was concluded that the technology used presented numerous advantages. Overall disturbance of the area was reduced, and allowed other measures to be implemented, including segregation of the highly impacted peat layer. It was expected that remediation objectives for the entire site will be met by July 2005. 3 refs., 3 tabs

Soil remediation of a former power plant site in Tulita, Northwest Territories

Energy Technology Data Exchange (ETDEWEB)

Pouliot, Y.; Thomassin-Lacroix, E. [Biogenie Inc., Lachenaie, PQ (Canada); Moreau, N. [Biogenie, Quebec City, PQ (Canada)

2005-07-01

This paper outlines major stages of an ongoing remediation project caused by a power generating plant in the Dene Hamlet of Tulita. High levels of soil contamination were caused by the plant's operations as well as accidental petroleum hydrocarbon (PHC) spills. The decommissioning of the plant required that the site be remediated. Challenges faced by the remediators included the high level of contamination, the remote location of the community, as well as the fact that the site was located in the centre of the community. In addition, the soil in the impacted site was fine, and a 20 cm thick layer of peat acted as sponge, absorbing and trapping hydrocarbons. Remedial criteria was outlined according to Canada-Wide Standards for fine-grained soil in an industrial setting. The technology used for the project was Biopile, a process consisting of installing wells in the contaminated zone in order to provide the aeration required for PHC biodegradation and to condition the soil on a regular basis in order to promote optimal treatment conditions throughout the impacted material. Results indicated that the first 2 months were successful in reducing initial PHC levels. However, the following treatment season did not show as much degradation. An investigation revealed that nitrogen and phosphorus levels were insufficient to sustain microbial activity, as a result of lower than normal temperatures in the area for that season. Nutrients were added to the soil to re-establish the appropriate treatment conditions. It was concluded that the technology used presented numerous advantages. Overall disturbance of the area was reduced, and allowed other measures to be implemented, including segregation of the highly impacted peat layer. It was expected that remediation objectives for the entire site will be met by July 2005. 3 refs., 3 tabs.

Screening of native plant species for phytoremediation potential at a Hg-contaminated mining site.

Science.gov (United States)

Marrugo-Negrete, José; Marrugo-Madrid, Siday; Pinedo-Hernández, José; Durango-Hernández, José; Díez, Sergi

2016-01-15

Artisanal and small-scale gold mining (ASGM) is the largest sector of demand for mercury (Hg), and therefore, one of the major sources of Hg pollution in the environment. This study was conducted in the Alacrán gold-mining site, one of the most important ASGM sites in Colombia, to identify native plant species growing in Hg-contaminated soils used for agricultural purposes, and to assess their potential as phytoremediation systems. Twenty-four native plant species were identified and analysed for total Hg (THg) in different tissues (roots, stems, and leaves) and in underlying soils. Accumulation factors (AF) in the shoots, translocation (TF) from roots to shoots, and bioconcentration (BCF) from soil-to-roots were determined. Different tissues from all plant species were classified in the order of decreasing accumulation of Hg as follows: roots > leaves > stems. THg concentrations in soil ranged from 230 to 6320 ng g(-1). TF values varied from 0.33 to 1.73, with high values in the lower Hg-contaminated soils. No correlation was found between soils with low concentrations of Hg and plant leaves, indicating that TF is not a very accurate indicator, since most of the Hg input to leaves at ASGM sites comes from the atmosphere. On the other hand, the BCF ranged from 0.28 to 0.99, with Jatropha curcas showing the highest value. Despite their low biomass production, several herbs and sub-shrubs are suitable for phytoremediation application in the field, due to their fast growth and high AF values in large and easily harvestable plant parts. Among these species, herbs such as Piper marginathum and Stecherus bifidus, and the sub-shrubs J. curcas and Capsicum annuum are promising native plants with the potential to be used in the phytoremediation of soils in tropical areas that are impacted by mining.

First detection in the USA: new plant pathogen, Phytophthora tentaculata, in native plant nurseries and restoration sites in California

Science.gov (United States)

S. Rooney-Latham; C. L. Blomquist; T. Swiecki; E. Bernhardt; S.J. Frankel

2015-01-01

Phytophthora tentaculata Kröber & Marwitz, has been detected in several native plant nurseries in 4 California counties and in restoration sites on orange sticky monkey flower (Diplacus aurantiacus subsp. aurantiacus (W. Curtis) Jeps. [Scrophulariaceae]), toyon (Heteromeles...

The importante of physical and mathematical models for nuclear power plants site selection

International Nuclear Information System (INIS)

Rios, J.L.P.

1989-01-01

The importance of the release of effluents from nuclear installations for the site selection of nuclear power plants is discussed. The main available analysis methods, physical and mathematical, is presented [pt

Profile of drowning victims in a coastal community.

Science.gov (United States)

Nichter, M A; Everett, P B

1989-02-01

Accidental drowning accounts for 15% of all accidental deaths in Pinellas County, Florida, and this study was conducted to better understand the epidemiologic profile of the victim. The medical examiner's records of 230 drownings in Pinellas County from January 1, 1983, through December 31, 1987, were reviewed for demographic and epidemiologic data. Bodies of salt water were the most common drowning site (47%), followed by swimming pools (22%), lakes (11%), baths (7%), and canals (6%). The drowning incidence for males was more than three times that for females. Drowning was endemic among boys less than five years of age (30/100,000/year). Fifty-nine percent of young adult victims had detectable postmortem blood alcohol levels. Drowning rates were highest among children less than five years and adults more than 80 years. Epidemiologic profiles of populations at risk and contributing factors are described and public safety measures are suggested.

Main phases of siting for nuclear power plants with review of required investigations

International Nuclear Information System (INIS)

Malbasa, N.

1984-01-01

The purpose of the article is a short description of the main phases in the process of siting for nuclear power plants as interpreted and applied by the Institut za elektroprivredu, Zagreb in the screening, comparison and evaluation of the sites for NPPs in the SR of Croatia. The scope and purpose, as well as review of required data and investigations for each particular phase are given. Common used methods for the comparison of sites are described and example of rejection criteria applicable for early phases of the siting is proposed. It is given a list of the most important activities which detailed analysis id indispensable for ending of the evaluation and getting a site permit from the regulatory body. A legal and regulatory basis for carrying out the siting process is also described. (author)

Procedures for evaluation of vibratory ground motions of soil deposits at nuclear power plant sites

International Nuclear Information System (INIS)

1975-06-01

According to USNRC requirements set forth in Appendix A, 10 CFR, Part 100, vibratory ground motion criteria for a nuclear plant must be based on local soil conditions, as well as on the seismicity, geology, and tectonics of the region. This report describes how such criteria can be developed by applying the latest technology associated with analytical predictions of site-dependent ground motions and with the use of composite spectra obtained from the current library of strong motion records. Recommended procedures for defining vibratory ground motion criteria contain the following steps: (1) geologic and seismologic studies; (2) site soils investigations; (3) site response sensitivity studies; (4) evaluation of local site response characteristics; (5) selection of site-matched records; and (6) appraisal and selection of seismic input criteria. An in-depth discussion of the engineering characteristics of earthquake ground motions including parameters used to characterize earthquakes and strong motion records, geologic factors that influence ground shaking, the current strong motion data base, and case histories of the effects of past earthquake events is presented. Next, geotechnical investigations of the seismologic, geologic, and site soil conditions required to develop vibratory motion criteria are briefly summarized. The current technology for establishing vibratory ground motion criteria at nuclear plant sites, including site-independent and site-dependent procedures that use data from strong motion records and from soil response analyses is described. (auth)

[Radiobiological effects on plants and animals within Semipalatinsk Test Site (Kazakhstan)].

Science.gov (United States)

Mozolin, E M; Geras'kin, S A; Minkenova, K S

2008-01-01

The Semipalatinsk Test Site (STS) was the main place of nuclear devices tests in the former Soviet Union. From 1949 to 1989 about 460 nuclear explosions have been carried out at STS. Radioactive contamination of STS territory has the extremely non-uniform character. The main dose-forming radionuclides are 137Cs, 90Sr, 152Eu, as well as 154Eu, 60CO, 239,240Pu and 241Am. The greatest specific activity of 137Cs and 239,240Pu in ground are n x 10(3) kBk/kg, 152Eu - 96 kBk/kg, 154Eu - 10.4 kBk/kg, 60Co - 20.5 kBk/kg, 241Am - 15 kBk/kg. However, up to now, within STS sites exists where gamma-dose rate comes to 60 microGy/h, that is enough for induction reliable biological effects in animals and plants. Inhabiting territory of STS plants and animals are characterized by increased level of mutagenesis, changes of morpho-anatomic indices and parameters of peripheral blood, by the increase of asymmetry bilateral indices, change of composition and structure of communities.

Modeling of 137Cs and 90Sr behavior in the soil-plant system within the territory adjacent to 'Experimental field' technical site in the Semipalatinsk test site

International Nuclear Information System (INIS)

Spiridonov, S.I.; Gontarenko, I.A.; Mukusheva, M.K.

2005-01-01

Modelling of 137 Cs and 90 Sr behavior in the soil-plant system is presented. Models have been parameterized for the area adjacent to the 'Experimental Field' Technical Site of the Semipalatinsk Test Site. The models describe the main processes responsible for changes of 137 Cs and 90 Sr content in the soil solution and, thereby, dynamics of radionuclides intake by vegetation. Results are presented from perspective and retrospective calculations, that reflect the dynamics of 137 and 90 Sr distribution by species in soil after nuclear explosions. The importance of factors governing radionuclide accumulation in plants within Semipalatinsk test site area is assessed. The analysis of sensitivity of model output variable to change in its parameters has revealed that the key soil properties significantly influence the results of prediction of radionuclide content in plants. (author)

Radiation environmental monitoring and assessment of plant-221 site ten years after decommissioning

International Nuclear Information System (INIS)

Li Yang; Gu Zhijie; Pan Wei; Ren Xiaona; Hu Xiaolin; She Haiqiang

2011-01-01

More than 10 years have passed since nuclear facility decommissioning practice for Plant-221 finished. Environmental radiation monitoring and post assessment of the decommissioning site of Plant-221 was carried out during 2003-2006, which was organized by Department of Environmental Protection and executed by China Institute for Radiation Protection, Environmental Radiation Monitoring station of Qinghai Province, etc. It shows that the decommissioning practice for Plant-221 complied with relevant limits for decommissioning, and its environmental radiation situation has not had significant change in general after 10 years, and the potential impact to the public and the environmental is acceptable. (authors)

Calibration of a Plant Uptake Model with Plant- and Site-Specific. Data for Uptake of Chlorinated Organic Compounds into Radish

DEFF Research Database (Denmark)

Trapp, Stefan

2015-01-01

The uptake of organic pollutants by plants is an important process for the exposure of humans to toxic chemicals. The objective of this study was to calibrate the parameters of a common plant uptake model by comparison to experimental results from literature. Radish was grown in contaminated soil...... with default data and site-specific data were similar. Deposition from air was the major uptake mechanism into shoots. Transport from soil with resuspended particles was only relevant for the contaminated plot. The calculation results (in dry weight) were most sensitive to changes of the water content of plant...

Characterization recommendations for waste sites at the Savannah River Plant

International Nuclear Information System (INIS)

Carlton, W.H.; Gordon, D.E.; Johnson, W.F.; Kaback, D.S.; Looney, B.B.; Nichols, R.L.; Shedrow, C.B.

1987-11-01

One hundred and sixty six disposal facilities that received or may have received waste materials resulting from operations at the Savannah River Plant (SRP) have been identified. These waste range from innocuous solid and liquid materials (e.g., wood piles) to process effluents that contain hazardous and/or radioactive constituents. The waste sites have been grouped into 45 categories according the the type of waste materials they received. Waste sites are located with SRP coordinates, a local Department of Energy (DOE) grid system whose grid north is 36 degrees 22 minutes west of true north. DOE policy is to close all waste sites at SRP in a manner consistent with protecting human health and environment and complying with applicable environmental regulations (DOE 1984). A uniform, explicit characterization program for SRP waste sites will provide a sound technical basis for developing closure plans. Several elements are summarized in the following individual sections including (1) a review of the history, geohydrology, and available characterization data for each waste site and (2) recommendations for additional characterization necessary to prepare a reasonable closure plan. Many waste sites have been fully characterized, while others have not been investigated at all. The approach used in this report is to evaluate available groundwater quality and site history data. For example, groundwater data are compared to review criteria to help determine what additional information is required. The review criteria are based on regulatory and DOE guidelines for acceptable concentrations of constituents in groundwater and soil

Seismically-induced soil amplification at the DOE Paducah Gaseous Diffusion Plant site

International Nuclear Information System (INIS)

Sykora, D.W.; Haynes, M.E.

1991-01-01

A site-specific earthquake site response (soil amplification) study is being conducted for the Department of Energy (DOE), Paducah Gaseous Diffusion Plant (PGDP). This study is pursuant to an upgraded Final Safety Analysis Report in accordance with requirements specified by DOE. The seismic hazard at PGDP is dominated by the New Madrid Seismic Zone. Site-specific synthetic earthquake records developed by others were applied independently to four soil columns with heights above baserock of about 325 ft. The results for the 1000-year earthquake event indicate that the site period is between 1.0 and 1.5 sec. Incident shear waves are amplified at periods of motion greater than 0.15 sec. The peak free-field horizontal acceleration, occurring at very low periods, is 0.28 g. 13 refs., 13 figs

Seismically-induced soil amplification at the DOE Paducah Gaseous Diffusion Plant Site

International Nuclear Information System (INIS)

Sykora, D.W.; Hynes, M.E.; Brock, W.R.; Hunt, R.J.; Shaffer, K.E.

1991-01-01

A site-specific earthquake site response (soil amplification) study is being conducted for the Department of Energy (DOE), Paducah Gaseous Diffusion Plant (PGDP). This study is pursuant to an upgraded Final Safety Analysis Report in accordance with requirements specified by DOE. The seismic hazard at PGDP is dominated by the New Madrid Seismic Zone. Site-specific synthetic earthquake records developed by others were applied independently to four soil columns with heights above baserock of about 325 ft. The results for the 1000-year earthquake event indicate that the site period is between 1.0 and 1.5 sec. Incident shear waves are strongly amplified at periods of motion greater than 0.3 sec. The peak free-field horizontal acceleration, occurring at very low periods, is 0.28 g

Plant water status relationships among major floodplain sites of the Flathead River, Montana

Science.gov (United States)

Lee, L.C.; Hinckley, T.M.; Scott, M.L.

1985-01-01

Water status measurements of dominant species from major floodplain plant community types of the North Fork Flathead River, Montana were used to test the accuracy of site moisture gradient relationships postulated from floristic ordinations and site water balance estimates. Analysis of variance tests showed significant differences among the average predawn xylem pressure potential (ψp) of species in several community types. However, additional analyses failed to indicate a significant degree of association between averaged predawn Yp measurements and either floristic ordination or site water balance results. Sixty eight percent of 22 trials comparing the diurnal average ψp of the same species in different community types on the same day were less negative for a species in the wetter community types as predicted by floristic ordinations. Similarly, 64% of the trials indicated that the diurnal average stomatal conductance was higher for a species in the wetter type. These results suggest that although a floodplain moisture gradient exists, it alone does not limit the distribution of floodplain plant communities in the North Fork.

Hydrological dispersion of radioactive material in relation to nuclear power plant siting

International Nuclear Information System (INIS)

1985-01-01

This Guide discusses the dispersion of normal and accidental releases of radioactive materials from nuclear power plants into surface water, including the washout of airborne radionuclides, and gives recommendations on information to be collected during the various stages of the siting procedure, a minimum measurement programme and the selection and validation of appropriate mathematical models for predicting dispersion. Guidelines are also provided for the optimal use of models for a specific site situation and for defining the necessary input parameters. Results of existing validation studies are given

Seismic Vulnerability Assessment of Site-Vicinity Infrastructure for Supporting the Accident Management of a Nuclear Power Plant

Directory of Open Access Journals (Sweden)

T. J. Katona

2017-01-01

Full Text Available Nuclear power plants shall be designed to resist the effects of large earthquakes. The design basis earthquake affects large area around the plant site and can cause serious consequences that will affect the logistical support of the emergency actions at the plant, influence the psychological condition of the plant personnel, and determine the workload of the country’s disaster management personnel. In this paper the main qualitative findings of a study are presented that have been performed for the case of a hypothetical 10−4/a probability design basis earthquake for the Paks Nuclear Power Plant, Hungary. The study covers the qualitative assessment of the postearthquake conditions at the settlements around the plant site including quantitative evaluation of the condition of dwellings. The main goal of the recent phase of the study was to identify public utility vulnerabilities that define the outside support conditions of the nuclear power plant accident management. The results of the study can be used for the planning of logistical support of the plant accident management staff. The study also contributes to better understanding of the working conditions of the disaster management services in the region around the nuclear power plant.

Dispersion of radioactive material in air and water and consideration of population distribution in site evaluation for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

The IAEA issues Safety Requirements and Safety Guides pertaining to nuclear power plants and activities in the field of nuclear energy, on the basis of its Safety Fundamentals publication on The Safety of Nuclear Installations. The present Safety Guide, which supplements the Code on the Safety of Nuclear Power Plants: Siting, concerns the effects of a nuclear power plant on the surrounding region and the consideration of population distribution in the siting of a plant. This Safety Guide makes recommendations on how to meet the requirements of the Code on the Safety of Nuclear Power Plants: Siting, on the basis of knowledge of the mechanisms for the dispersion of effluents discharged into the atmosphere and into surface water and groundwater. Relevant site characteristics and safety considerations are discussed. Population distribution, the projected population growth rate, particular geographical features, the capabilities of local transport networks and communications networks, industry and agriculture in the region, and recreational and institutional activities in the region should be considered in assessing the feasibility of developing an emergency response plan. In the selection of a site for a facility using radioactive material, such as a nuclear power plant, account should be taken of any local features that might be affected by the facility and of the feasibility of off-site intervention, including emergency response and protective actions. This is in addition to the evaluation of any features of the site itself that might affect the safety of the facility. This Safety Guide recommends methods for the assessment of regional and local characteristics. This Safety Guide supersedes four earlier IAEA Safety Guides, namely: Atmospheric Dispersion in Nuclear Power Plant Siting (Safety Series No. 50-SG-S3 (1980)). Site Selection and Evaluation for Nuclear Power Plants with Respect to Population Distribution (Safety Series No. 50-SG-S4 (1980)). Hydrological

Dispersion of radioactive material in air and water and consideration of population distribution in site evaluation for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2002-01-01

The IAEA issues Safety Requirements and Safety Guides pertaining to nuclear power plants and activities in the field of nuclear energy, on the basis of its Safety Fundamentals publication on The Safety of Nuclear Installations. The present Safety Guide, which supplements the Code on the Safety of Nuclear Power Plants: Siting, concerns the effects of a nuclear power plant on the surrounding region and the consideration of population distribution in the siting of a plant. This Safety Guide makes recommendations on how to meet the requirements of the Code on the Safety of Nuclear Power Plants: Siting, on the basis of knowledge of the mechanisms for the dispersion of effluents discharged into the atmosphere and into surface water and groundwater. Relevant site characteristics and safety considerations are discussed. Population distribution, the projected population growth rate, particular geographical features, the capabilities of local transport networks and communications networks, industry and agriculture in the region, and recreational and institutional activities in the region should be considered in assessing the feasibility of developing an emergency response plan. In the selection of a site for a facility using radioactive material, such as a nuclear power plant, account should be taken of any local features that might be affected by the facility and of the feasibility of off-site intervention, including emergency response and protective actions. This is in addition to the evaluation of any features of the site itself that might affect the safety of the facility. This Safety Guide recommends methods for the assessment of regional and local characteristics. This Safety Guide supersedes four earlier IAEA Safety Guides, namely: Atmospheric Dispersion in Nuclear Power Plant Siting (Safety Series No. 50-SG-S3 (1980)); Site Selection and Evaluation for Nuclear Power Plants with Respect to Population Distribution (Safety Series No. 50-SG-S4 (1980)); Hydrological

Site quality influence over understory plant diversity in old-growth and harvested Nothofagus pumilio forests

Directory of Open Access Journals (Sweden)

E. A. Gallo

2013-04-01

Full Text Available Aim of study: The effects and interactions of shelterwood forest harvesting and site qualities over understory plant species diversity and composition were compared among primary and harvested Nothofagus pumilio forests.Area of study: Tierra del Fuego (Argentina, on three pure conditions (one and six year-old harvested, and primary without previous harvesting forests and three site qualities (high, medium and low.Material and Methods: Understory richness and cover (% were registered in five replicates of 1 hectare each per treatment. Taxonomic species were classified in categories (groups, origin and life forms. Two-way ANOVAs and multivariate analyses were conducted.Main results: Shelterwood harvesting and site quality significantly influenced understory cover and richness, which allow the introduction of native and exotic species and increasing of dicot and monocot covers. In dicots, monocots, exotics and total groups, higher richness and covers were related to time. Meanwhile, cover reached similar high values in all site qualities on dicot, native and total groups. On the other hand, monocot and exotic richness and cover remain similar in primary and recently harvested forests, and greatly increased in old harvested forests. Mosses and ferns were among the most sensitive groups.Research highlights: Impacts of shelterwood cut depend on site quality of the stands and time since harvesting occurs. For this, different site quality stands should received differential attention in the development of conservation strategies, as well as variations in the shelterwood implementation (as irregularity and patchiness should be considered to better promote understory plant species conservation inside managed areas.Key words: plant species conservation; years after harvesting; forest management; Tierra del Fuego.

Optical technologies applied alongside on-site and remote approaches for climate gas emission quantification at a wastewater treatment plant

DEFF Research Database (Denmark)

Samuelsson, Jerker; Delre, Antonio; Tumlin, Susanne

2018-01-01

Plant-integrated and on-site gas emissions were quantified from a Swedish wastewater treatment plant by applying several optical analytical techniques and measurement methods. Plant-integrated CH4 emission rates, measured using mobile ground-based remote sensing methods, varied between 28.5 and 33.......5 kg CH4 h−1, corresponding to an average emission factor of 5.9% as kg CH4 (kg CH4production) −1, whereas N2O emissions varied between 4.0 and 6.4 kg h−1, corresponding to an average emission factor of 1.5% as kg N2O-N (kg TN influent) −1. Plant-integrated NH3 emissions were around 0.4 kg h−1...... quantifications were approximately two-thirds of the plant-integrated emission quantifications, which may be explained by the different timeframes of the approaches and that not all emission sources were identified during on-site investigation. Off-site gas emission quantifications, using ground-based remote...

THREE-DIMENSIONAL GEOFILTRATIONAL MODEL OF THE ROGUN HYDRO POWER PLANT CONSTRUCTION SITE

Directory of Open Access Journals (Sweden)

Khokhotva Sergey Nikolaevich

2017-05-01

Full Text Available The article deals with technique of creation and results of calculations of the three-dimensional geofiltrational model of the Rogun HPP construction site. When performing works on creation of the Rogun HPP three-dimensional geofiltration model, geological and hydrogeological conditions of the Rogun HPP construction site were analyzed. They showed that the construction site consists mostly of fractured rocks of various weathering degrees. In terms of preservation, four preservation zones were identified in the rock mass. These zones define the features of hydrogeological conditions that have emerged in the area of construction. Calculation results illustrated the absence of seepage areas on the lower slope of dam; this is the indication of normal operation of the dam impervious circuit. The drainage system of the underground hydropower plant has a high efficiency. Operation of the drainage galleries complex leads to a significant reduction of piezometric pressure on roofs of the machine and transformer halls. Above the underground structures a completely drained area is formed. Completed forecast calculations on geofiltration model of the Rogun hydropower plant determine the hydrostatic pressure and piezometric pressure at any point of the modeled area. These data can be used as loads while designing of lining of underground workings.

Egg laying site selection by a host plant specialist leaf miner moth at two intra-plant levels in the northern Chilean Atacama Desert

Directory of Open Access Journals (Sweden)

José Storey-Palma

2014-09-01

Full Text Available Egg laying site selection by a host plant specialist leaf miner moth at two intra-plant levels in the northern Chilean Atacama Desert. The spatial distribution of the immature stages of the leaf miner Angelabella tecomae Vargas & Parra, 2005 was determined at two intra-plant levels (shoot and leaflet on the shrub Tecoma fulva fulva (Cav. D. Don (Bignoniaceae in the Azapa valley, northern Chilean Atacama Desert. An aggregated spatial pattern was detected for all the immature stages along the shoot, with an age dependent relative position: eggs and first instar larvae were clumped at apex; second, third and fourth instar larvae were mostly found at intermediate positions; meanwhile the spinning larva and pupa were clumped at basis. This pattern suggests that the females select new, actively growing leaflets for egg laying. At the leaflet level, the immature stages were found more frequently at underside. Furthermore, survivorship was higher for larvae from underside mines. All these results highlight the importance of an accurate selection of egg laying site in the life history of this highly specialized leaf miner. By contrast, eventual wrong choices in the egg laying site selection may be associated with diminished larval survivorship. The importance of the continuous availability of new plant tissue in this highly human modified arid environment is discussed in relation with the observed patterns.

Conflicts concerning sites for waste treatment and waste disposal plants

International Nuclear Information System (INIS)

Werbeck, N.

1993-01-01

The erection of waste treatment and waste disposal flants increasingly meets with the disapproval of local residents. This is due to three factors: Firstly, the erection and operation of waste treatment plants is assumed to necessarily entail harmful effects and risks, which may be true or may not. Secondly, these disadvantages are in part considered to be non-compensable. Thirdly, waste treatment plants have a large catchment area, which means that more people enjoy their benefits than have to suffer their disadvantages. If residents in the vicinity of such plants are not compensated for damage sustained or harmed in ways that cannot be compensated for it becomes a rational stance for them, while not objecting to waste treatment and waste disposal plants in principle to object to their being in their own neighbourhood. The book comprehensively describes the subject area from an economic angle. The causes are analysed in detail and an action strategy is pointed, out, which can help to reduce acceptance problems. The individual chapters deal with emissions, risk potentials, optimization calculus considering individual firms or persons and groups of two or more firms or persons, private-economy approaches for the solving of site selection conflicts, collective decision-making. (orig./HSCH) [de

Seismic safety margins research program. Phase I final report - Plant/site selection and data collection (Project I)

International Nuclear Information System (INIS)

Chuang, T.Y.

1981-07-01

Project I of Phase I of the Seismic Safety Margins Research Program (SSMRP) comprised two parts: the selection of a representative nuclear power plant/site for study in Phase I and the collection of data needed by the other SSMRP projects. Unit 1 of the Zion Nuclear Power Plant in Zion, Illinois, was selected for the SSMRP Phase I studies. Unit 1 of the Zion plant has been validated as a good choice for the Phase I study plant. Although no single nuclear power plant can represent all such plants equally well, selection criteria were developed to maximize the generic implications of Phase I of the SSMRP. On the basis of the selection criteria, the Zion plant and its site were found to be reasonably representative of operating and future plants with regard to its nuclear steam supply system; the type of containment structure (prestressed concrete); its electrical capacity (1100 MWe); its location (the Midwest); the peak seismic acceleration used for design (0.17g); and the properties of the underlying soil (the low-strain shear-wave velocity is 1650 ft/s in a 50- to 100-ft-thick layer of soil overlying sedimentary bedrock). (author)

Hanford site as it relates to an alternative site for the Waste Isolation Pilot Plant: an environmental description

Energy Technology Data Exchange (ETDEWEB)

Fecht, K.R. (ed.)

1978-12-01

The use of basalt at Hanford as an alternative for the Waste Isolation Pilot Plant (WIPP) would require that the present Basalt Waste Isolation Program (BWIP) at Hanford be expanded to incorporate the planned WIPP functions, namely the permanent storage of transuranic (TRU) wastes. This report discusses: program costs, demography, ecology, climatology, physiography, hydrology, geology, seismology, and historical and archeological sites. (DLC)

Hanford site as it relates to an alternative site for the Waste Isolation Pilot Plant: an environmental description

International Nuclear Information System (INIS)

Fecht, K.R.

1978-12-01

The use of basalt at Hanford as an alternative for the Waste Isolation Pilot Plant (WIPP) would require that the present Basalt Waste Isolation Program (BWIP) at Hanford be expanded to incorporate the planned WIPP functions, namely the permanent storage of transuranic (TRU) wastes. This report discusses: program costs, demography, ecology, climatology, physiography, hydrology, geology, seismology, and historical and archeological sites

Environmental Insights from Siting New Nuclear Power Plants in the United States

International Nuclear Information System (INIS)

Kugler, Andrew J.

2013-01-01

This described the Part 52 combined licence review process, under which a design certification and an early site permit can come together to allow a limited work authorization to be issued for pre-construction work while the combined Construction and Operation Licence (COL) application is being considered by the regulator. The regulatory then performs ITAAC (Inspection, Test, Analysis, Acceptance Criteria) to verify that the as-build plant conforms to what was licensed. The Siting Safety Review that is performed under the COL process considers factors such as geology, surface faulting, seismology, geotechnical engineering, hydrology, flooding and groundwater. For an existing site, this involves updating the hazard evaluation from the original one. Dose consequence calculations are performed for both design basis accidents and severe accidents. Experience with siting has shown that all applicants deviate from the guidance, that it is difficult to compare existing sites with new sites, that water supply is a bigger issue now than it was for existing reactors and that site selection can come down to a choice 'among the best', rather than the 'best possible'. Consideration of alternative sites is a big part of the process; the U.S.NRC can reject a primary site if an alternative site appears to be more appropriate, though it cannot force an applicant to select a secondary site

75 FR 11920 - General Electric Lighting-Ravenna Lamp Plant, Lighting Division, Including On-Site Leased Workers...

Science.gov (United States)

2010-03-12

... to the production of high intensity discharge lamps. The review shows that on August 24, 2007, a...-Ravenna Lamp Plant, Lighting Division, Including On-Site Leased Workers from Devore Technologies, Ravenna..., 2009, applicable to workers of General Electric Lighting-Ravenna Lamp Plant, Lighting Division...

Preliminary results on food consumption rates for off-site dose calculation of nuclear power plants

International Nuclear Information System (INIS)

Lee, Gab Bock; Chung, Yang Geun; Bang, Sun Young; Kang, Duk Won

2005-01-01

The Internal dose by food consumption mostly account for radiological dose of public around nuclear power plants(NPP). But, food consumption rate applied to off-site dose calculation in Korea which is the result of field investigation around Kori NPP by the KAERI in 1988. is not reflected of the latest dietary characteristics. The Ministry of Health and Welfare Affairs has investigated the food and nutrition of nations every 3 years based on the Law of National Health Improvement. To update the food consumption rates of the maximum individual, the analysis of the national food investigation results and field surveys around nuclear power plant sites have been carried out

Pollution prevention opportunity assessment for the K-25 Site Steam Plant -- Level 3

International Nuclear Information System (INIS)

1995-09-01

A Level 3 pollution prevention opportunity assessment (PPOA) was performed for the K-1501 Steam Plant at the K-25 Site. The primary objective was to identify and evaluate pollution prevention (P2) options to reduce the quantities of each waste stream generated by the Steam Plant. For each of the waste streams, P2 options were evaluated to first reduce the quantity of waste generated and second to recycle the waste. This report provides a process description of the facility; identification, evaluation, and recommendations of P2 options; an implementation schedule with funding sources; and conclusions. Largely for economic reasons, only 3 of the 14 P2 options are being recommended for implementation. All are source reduction options. When implemented, these three options are estimated to reduce the annual generation of waste by 658,412 kg and will result in a cost savings of approximately $29,232/year for the K-25 Site. The recommended options are to: install a flue gas return System in Boiler 7; reduce steam loss from traps; and increase lapse time between rinses. The four boilers currently in operation at the Steam Plant use natural gas or fuel oil as fuel sources

Probabilistic siting analysis of nuclear power plants emphasizing atmospheric dispersion of radioactive releases and radiation-induced health effects

International Nuclear Information System (INIS)

Savolainen, Ilkka

1980-01-01

A presentation is made of probabilistic evaluation schemes for nuclear power plant siting. Effects on health attributable to ionizing radiation are reviewed, for the purpose of assessment of the numbers of the most important health effect cases in light-water reactor accidents. The atmospheric dispersion of radioactive releases from nuclear power plants is discussed, and there is presented an environmental consequence assessment model in which the radioactive releases and atmospheric dispersion of the releases are treated by the application of probabilistic methods. In the model, the environmental effects arising from exposure to radiation are expressed as cumulative probability distributions and expectation values. The probabilistic environmental consequence assessment model has been applied to nuclear power plant site evaluation, including risk-benefit and cost-benefit analyses, and the comparison of various alternative sites. (author)

Idaho Chemical Processing Plant Site Development Plan

International Nuclear Information System (INIS)

Ferguson, F.G.

1994-02-01

The Idaho Chemical Processing Plant (ICPP) mission is to receive and store spent nuclear fuels and radioactive wastes for disposition for Department of Energy (DOE) in a cost-effective manner that protects the safety of Idaho National Engineering Laboratory (INEL) employees, the public, and the environment by: Developing advanced technologies to process spent nuclear fuel for permanent offsite disposition and to achieve waste minimization. Receiving and storing Navy and other DOE assigned spent nuclear fuels. Managing all wastes in compliance with applicable laws and regulations. Identifying and conducting site remediation consistent with facility transition activities. Seeking out and implementing private sector technology transfer and cooperative development agreements. Prior to April 1992, the ICPP mission included fuel reprocessing. With the recent phaseout of fuel reprocessing, some parts of the ICPP mission have changed. Others have remained the same or increased in scope

Final environmental impact assessment of the Paducah Gaseous Diffusion Plant site, Paducah, Kentucky

Energy Technology Data Exchange (ETDEWEB)

1982-08-01

This document considers: the need for uranium enrichment facilities; site location; plant description; and describes the power generating facilities in light of its existing environment. The impacts from continuing operations are compared with alternatives of shutdown, relocation, and alternative power systems. (PSB)

Remedial investigation for the chemical plant area of the Weldon Spring Site

International Nuclear Information System (INIS)

1992-11-01

The US Department of Energy (DOE) is responsible for management of the Weldon Spring Site Remedial Action Project (WSSRAP) under its Environmental Restoration and Waste Management Program. Major goals include eliminating potential public and environmental hazards due to site contamination and releasing the property for alternate uses to the maximum extent practicable. The purpose of the remedial investigation described in this report was to determine the extent of contamination associated with the portion of the Weldon Spring site known as the chemical plant and raffinate pit area. The DOE has assumed responsibility for investigating and remediating all on-site soil contamination and off-site soil which is radiologically contaminated as a result of uranium and thorium processing operations. The DOE has also assumed the responsibility for radiologically contaminated groundwater on and off site. The Weldon Spring site remedial investigation also involved the evaluation of the sources, nature and extent, and environmental fate and transport of contaminants to provide a basis for defining the risks that the contaminants may pose to human health and the environment. Data are included in this report to support the screening of remedial technologies and to permit the development and detailed analysis of alternatives for remedial action at the site during the feasibility study process

Assessment of earthquake-induced tsunami hazard at a power plant site

International Nuclear Information System (INIS)

Ghosh, A.K.

2008-01-01

This paper presents a study of the tsunami hazard due to submarine earthquakes at a power plant site on the east coast of India. The paper considers various sources of earthquakes from the tectonic information, and records of past earthquakes and tsunamis. Magnitude-frequency relationship for earthquake occurrence rate and a simplified model for tsunami run-up height as a function of earthquake magnitude and the distance between the source and site have been developed. Finally, considering equal likelihood of generation of earthquakes anywhere on each of the faults, the tsunami hazard has been evaluated and presented as a relationship between tsunami height and its mean recurrence interval (MRI). Probability of exceedence of a certain wave height in a given period of time is also presented. These studies will be helpful in making an estimate of the tsunami-induced flooding potential at the site

Design basis flood for nuclear power plants on river sites

International Nuclear Information System (INIS)

1983-01-01

The Guide presents techniques for determining the design basis flood (DBF) to be used for siting nuclear power plants at or near non-tidal reaches of rivers and for protecting nuclear power plants against floods. Since flooding of a nuclear power plant can have repercussions on safety, the DBF is always chosen to have a very low probability of exceedance per annum. The DBF may result from one or more of the following causes: (1) Precipitation, snowmelt; (2) Failure of water control structures, either from seismic or hydrological causes or from faulty operation of these structures; (3) Channel obstruction such as landslide, ice effects, log or debris jams, and effects of vulcanism. Normally the DBF is not less than any recorded or historical flood occurrence. For flood evaluation two types of methods are discussed in this Guide: probabilistic and deterministic. Simple probabilistic methods to determine floods of such low exceedance probability have a great degree of uncertainty and are presented for use only during the site survey. However, the more sophisticated probabilistic methods, the so-called stochastic methods, may give an acceptable result, as outlined in this Guide. The preferred method of evaluating the component of the DBF due to precipitation, as described in this Guide, is the deterministic one, based on the concept of a limit to the probable maximum precipitation (PMP) and on the unit hydrograph technique. Dam failures may generate a flood substantially more severe than that due to precipitation. The methodology for evaluating these types of floods is therefore presented in this Guide. Making allowance for the possible simultaneous occurrence of two or more important flood-producing events is also discussed here. The Guide does not deal with floods caused by sabotage

Subsurface fate and transport of cyanide species at a manufactured-gas plant site

International Nuclear Information System (INIS)

Ghosh, R.S.; Dzombak, D.A.; Luthy, R.G.; Nakles, D.V.

1999-01-01

Cyanide is present at manufactured-gas plant (MGP) sites in oxide-box residuals, which were often managed on-site as fill during active operations. Cyanide can leach from these materials, causing groundwater contamination. Speciation, fate, and transport of cyanide in a sand-gravel aquifer underlying an MGP site in the upper Midwest region of the US were studied through characterization, monitoring, and modeling of a plume of cyanide-contaminated groundwater emanating from the site. Results indicate that cyanide in the groundwater is primarily in the form of iron-cyanide complexes (>98%), that these complexes are stable under the conditions of the aquifer, and that they are transported as nonreactive solutes in the sand-gravel aquifer material. Weak-acid-dissociable cyanide, which represents a minute fraction of total cyanide in the site groundwater, may undergo chemical-biological degradation in the sand-gravel aquifer. It seems that dilution may be the only natural attenuation mechanism for iron-cyanide complexes in sand-gravel aquifers at MGP sites

Modeling time to recovery and initiating event frequency for loss of off-site power incidents at nuclear power plants

International Nuclear Information System (INIS)

Iman, R.L.; Hora, S.C.

1988-01-01

Industry data representing the time to recovery of loss of off-site power at nuclear power plants for 63 incidents caused by plant-centered losses, grid losses, or severe weather losses are fit with exponential, lognormal, gamma and Weibull probability models. A Bayesian analysis is used to compare the adequacy of each of these models and to provide uncertainty bounds on each of the fitted models. A composite model that combines the probability models fitted to each of the three sources of data is presented as a method for predicting the time to recovery of loss of off-site power. The composite model is very general and can be made site specific by making adjustments on the models used, such as might occur due to the type of switchyard configuration or type of grid, and by adjusting the weights on the individual models, such as might occur with weather conditions existing at a particular plant. Adjustments in the composite model are shown for different models used for switchyard configuration and for different weights due to weather. Bayesian approaches are also presented for modeling the frequency of initiating events leading to loss of off-site power. One Bayesian model assumes that all plants share a common incidence rate for loss of off-site power, while the other Bayesian approach models the incidence rate for each plant relative to the incidence rates of all other plants. Combining the Bayesian models for the frequency of the initiating events with the composite Bayesian model for recovery provides the necessary vehicle for a complete model that incorporates uncertainty into a probabilistic risk assessment

Problems of developing remedial strategy for the uranium ore processing legacy site Pridneprovsky Chemical Plant site (Dneprodzerginsk, Ukraine)

International Nuclear Information System (INIS)

Riazantsev, V.; Bugai, D.; Skalskyy, A.; Tkachenko, E.

2014-01-01

In this paper we present results of works and studies carried out in the frame of ongoing national and international projects aimed at developing the remedial strategy for the Soviet era legacy uranium production site Pridneprovsky Chemical Plant, Dneprodzerginsk, Ukraine. The site includes several uranium mill tailings, contaminated buildings, ore storage grounds and other contaminated facilities. Taking into account the necessity to implement provisions of the new IAEA standards (Radiation Protection and Safety of Radiation Sources: International Basic Safety Standards, No. GSR Part 3 (Interim) and others) as well as the provisions of the ICRP 103 publication, the State Nuclear Regulatory Inspectorate Ukraine developed the draft of the new licensing requirements for activities of uranium ores processing.

Improvement of Off-site Dose Assessment Code for Operating Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Kim, Juyub; Kim, Juyoul; Shin, Kwangyoung [FNC Technology Co. Ltd., Yongin (Korea, Republic of); You, Songjae; Moon, Jongyi [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2014-05-15

XOQDOQ code which calculates atmospheric Dispersion factor was included into INDAC also. A research on the improvement of off-site dose assessment system for an operating nuclear power plant was performed by KINS in 2011. As a result, following improvements were derived: - Separation of dose assessment for new and existing facilities - Update of food ingestion data - Consideration of multi-unit operation and so on In order to reflect the results, INDAC is under modification. INDAC is an integrated dose assessment code for an operating nuclear power plant and consists of three main modules: XOQDOQ, GASDOS and LIQDOS. The modules are under modification in order to improve the accuracy of assessment and usability. Assessment points for multi-unit release can be calculated through the improved code and the method on dose assessment for multi-unit release has been modified, so that the dose assessment result of multi-unit site becomes more realistic by relieving excessive conservatism. Finally, as the accuracy of calculation modules has been improved, the reliability of dose assessment result has been strengthened.

Environmental impacts of manufactured gas plant demolition: examples from site remediation experience

Energy Technology Data Exchange (ETDEWEB)

Unites, D. [Atlantic Environmental Services, Inc., Colchester, CT (United States)

1995-12-31

Inappropriate demolition of manufactured gas plant (MGP) sites may leave a continuing legacy in the environmental record. Much of the contamination encountered at former gas plants originated from on-site disposal or from spills and leaks during operations. However, some of the greatest potential for continual release comes from inappropriately decommissioned vessels and tanks. These structures contained liquids such as tars, oils, water, and other fluids associated with by-product removal or the gas stream purification process. Inorganic `solids` constitute another, although generally minor, source of contaminants during demolition. These contaminants include: cyanide- and sulfide-containing purifier materials; asbestos from roofing, pipe lagging, etc.; mercury from controls and manometers; and lead from painted surfaces. Normal elements of decommissioning and dismantling include: purging the piping system with inert gas; removal and sale of liquids having commercial value; disposal or abandonment of non-saleable liquids; scrapping and dismantling of above-grade metal vessels; abandonment of below-grade vessels; and demolition of above-grade buildings. Depending on the time from the cessation of operations to the demolition, some steps may have been omitted. Appropriate demolition would also take into account removal and disposal of asbestos, cyanide, lead, and mercury-containing materials prior to razing structures. By employing precautions during demolition, widespread contamination can be avoided and subsequent reuse of the site can be facilitated.

Solar total energy-large scale experiment, Shenandoah, Georgia site. Annual report, June 1977--June 1978. [For Bleyle Knitwear Plant

Energy Technology Data Exchange (ETDEWEB)

None,

1978-06-01

The site was described in terms of location, suitably, accessibility, and other factors. Detailed descriptions of the Solar Total Energy-Large Scale Experiment Application (STE-LSE) (Bleyle of America, Inc., Knitwear Plant), the DOE owned Meteorology Station operating at the site, and the instrumentation provided by the Georgia Power Company to measure energy usage within the knitwear plant are included. A detailed report of progress is given at the Shenandoah Site, introduced by the STE-LSE schedule and the Cooperative Agreement work tasks. Progress is described in terms of the following major task areas: site/application; instrumentation/data acquisition; meteorology station; site to STES interface; information dissemination. A brief overview of milestones to be accomplished is given, followed by these appendices: solar easement agreement, interface drawing set, and additional site background data. (MHR)

Earthworms drive succession of both plant and Collembola communities in post-mining sites

Czech Academy of Sciences Publication Activity Database

Mudrák, Ondřej; Uteseny, Karoline; Frouz, Jan

2016-01-01

Roč. 18, April (2016), EGU2016-8464 ISSN 1607-7962. [European Geosciences Union General Assembly 2016. 17.04.2016-22.04.2016, Vienna] Institutional support: RVO:60077344 ; RVO:67985939 Keywords : earthworms * succession * plant communities * Collembola communities * post-mining sites Subject RIV: DF - Soil Science

Lessons learned from an installation perspective for chemical demilitarization plant start-up at four operating incineration sites.

Energy Technology Data Exchange (ETDEWEB)

Motz, L.; Decision and Information Sciences

2011-02-21

This study presents the lessons learned by chemical storage installations as they prepared for the start of chemical demilitarization plant operations at the four current chemical incinerator sites in Alabama, Arkansas, Oregon, and Utah. The study included interviews with persons associated with the process and collection of available documents prepared at each site. The goal was to provide useful information for the chemical weapons storage sites in Colorado and Kentucky that will be going through plant start-up in the next few years. The study is not a compendium of what to do and what not to do. The information has been categorized into ten lessons learned; each is discussed individually. Documents that may be useful to the Colorado and Kentucky sites are included in the appendices. This study should be used as a basis for planning and training.

Earthquakes and associated topics in relation to nuclear power plant siting

International Nuclear Information System (INIS)

1979-01-01

The main emphasis of the Guide is on the determination of the design basis ground motions for the nuclear power plant and on the determination of the potential for surface faulting at the site. Additionally, the Guide treats initiation of seismically induced flooding and the ground failure phenomena of subsidence and collapse. Volcanic activity is not dealt with except in connection with tsunamis. The methods and procedures discussed in this Guide should be taken as the basis for the design of seismically safe nuclear power plants and are primarily suited to areas of high and medium seismicity; for areas of low seismicity the Guide may not be applicable in its entirety and may need to be supplemented by other methods

Multi-criteria GIS-based siting of an incineration plant for municipal solid waste.

Science.gov (United States)

Tavares, Gilberto; Zsigraiová, Zdena; Semiao, Viriato

2011-01-01

Siting a municipal solid waste (MSW) incineration plant requires a comprehensive evaluation to identify the best available location(s) that can simultaneously meet the requirements of regulations and minimise economic, environmental, health, and social costs. A spatial multi-criteria evaluation methodology is presented to assess land suitability for a plant siting and applied to Santiago Island of Cape Verde. It combines the analytical hierarchy process (AHP) to estimate the selected evaluation criteria weights with Geographic Information Systems (GIS) for spatial data analysis that avoids the subjectivity of the judgements of decision makers in establishing the influences between some criteria or clusters of criteria. An innovative feature of the method lies in incorporating the environmental impact assessment of the plant operation as a criterion in the decision-making process itself rather than as an a posteriori assessment. Moreover, a two-scale approach is considered. At a global scale an initial screening identifies inter-municipal zones satisfying the decisive requirements (socio-economic, technical and environmental issues, with weights respectively, of 48%, 41% and 11%). A detailed suitability ranking inside the previously identified zones is then performed at a local scale in two phases and includes environmental assessment of the plant operation. Those zones are ranked by combining the non-environmental feasibility of Phase 1 (with a weight of 75%) with the environmental assessment of the plant operation impact of Phase 2 (with a weight of 25%). The reliability and robustness of the presented methodology as a decision supporting tool is assessed through a sensitivity analysis. The results proved the system effectiveness in the ranking process. Copyright © 2011 Elsevier Ltd. All rights reserved.

Evaluation of nuclear power plant siting by probabilistic assessment of environmental impacts

International Nuclear Information System (INIS)

Vuori, S.

1978-01-01

The work consists of the description of a probabilistic consequence assessment model ARANO, and the individual calculation schemes therein included. This assessment model has been applied to the risk/benefit and cost/benefit analyses of the siting of nuclear power plants. In addition, there have been made some comparisons with the alternative fossil fuelled energy production scenarios. (author)

Preliminary geological study in kabupaten Pamekasan area to support the selection of candidate site of nuclear desalination plant

International Nuclear Information System (INIS)

Ngadenin; Lilik Subiantoro; Kurnia Setiawan Widana

2014-01-01

The area around the southern coast Pamekasan is one of the candidates for the alternatives location of nuclear desalination plant site. In 1949 around Sampang Madura ever tectonic earthquake measuring 5 on the Richter scale with its epicenter on land. Tectonic earthquake with epicenter on land is likely related to the presence of active faults on the Madura island. Location prospective nuclear desalination plant site should be away or free of active faults. The study aimed to obtain geological information and find out the characteristics of tectonics including active fault to support site studies of nuclear desalination plant on the island of Madura. The method used is the geological mapping scale, 1 : 50,000. Lithology in the area along the south coast district Pamekasan is alluvium Holocene age and conglomerate units of Pleistocene age. There were no indications of active faults in the region. Candidates site at this location is less attractive in terms of geotechnical foundation as can be ascertained bedrock will be found sufficient in that building construction will require expensive. (author)

Multicriteria decision analysis based on analytic hierarchy process in GIS environment for siting nuclear power plant in Egypt

International Nuclear Information System (INIS)

Abudeif, A.M.; Abdel Moneim, A.A.; Farrag, A.F.

2015-01-01

Highlights: • The binary overlay method was used in Phase I through OR operator for selecting the candidate areas. • The WLC and AHP methods was used to screen and select the potential sites (phase II) in Arc GIS 10.1 software. • In phase III, four sites, all located on the North western coast and Red Sea, of highest scores were chosen as Candidate sites after eliminating the lowest score sites. • The AHP method was applied to select preferred candidate site and calculating the eigenvectors in Expert Choice Software Package. - Abstract: Due to increasing demand of electrical energy and freshwater in Egypt, it is safe to assume that the decision makers will turn to nuclear power as the feasible alternative for energy. However, as time goes by, fewer sites will be available and suitable for nuclear power plant development. Site selection is a key phase of the siting process of a nuclear plant and may significantly affect the safety and cost of the facility during its entire life cycle. The siting of nuclear power plants is one of multi-criteria problems, which makes it complex. Many interrelated factors affect the process. Six constraints and twenty-two factors corresponding to safety, environment and socio-economy were considered in the siting study presented in this paper. Multi-Criteria Decision Analysis was applied during the selection of nuclear power plants site using GIS software. Three spatial decision making models were applied in this paper during site selection stage. The binary overlay (Boolean logic) with Low Risk approach in which the logical OR operator is used to determine the candidate areas. All constraints were represented in binary maps, combined and a masking layer was created to eliminate the lands considered as constraints in Arc GIS Software. The 22 factors were represented in normalized maps after unifying all of them to 0–1 score scales based on the philosophy of suitability criteria (factors) using the Weighted Linear Combination

75 FR 38127 - Visteon Systems, LLC North Penn Plant Electronics Products Group Including On-Site Leased Workers...

Science.gov (United States)

2010-07-01

..., North Penn Plant, Electronics Products Group to be covered by this certification. The intent of the... North Penn Plant Electronics Products Group Including On-Site Leased Workers From Ryder Integrated... Certification Regarding Eligibility To Apply for Worker Adjustment Assistance and Alternative Trade Adjustment...

Middlesex Sampling Plant [MSP] annual site environmental report, calendar year 1988

International Nuclear Information System (INIS)

1989-04-01

The environmental monitoring program, which began in 1980, was continued in 1988 at the former Middlesex Sampling Plant (MSP) site, located in the Borough of Middlesex, New Jersey. The MSP site is part of the Formerly Utilized Site Remedial Action Program (FUSRAP), a Department of Energy (DOE) program to decontaminate or otherwise control sites where residual radioactive materials remain either from the early years of the nation's atomic energy program or from commercial operations causing conditions that Congress has mandated DOE to remedy. The environmental monitoring program is carried out by Bechtel National, Inc. (BNI), project management contractor for FUSRAP. The monitoring program at the MSP measures radon concentrations in air; external gamma radiation levels; and uranium and radium concentrations in surface water, groundwater, and sediment. To verify that the site is in compliance with the DOE radiation protection standard (100 mrem/yr) and to assess its potential effect on public health, the radiation dose was calculated for a hypothetical maximally exposed individual. Results of the 1988 monitoring show that the MSP is in compliance with applicable DOE radiation protection standards and with applicable requirements specified by New Jersey Department of Environmental Protection groundwater permits. 17 refs., 15 figs., 21 tabs

Environmental Restoration Site-Specific Plan for the Portsmouth Gaseous Diffusion Plant, FY 93

International Nuclear Information System (INIS)

1993-01-01

The purpose of this Site-Specific Plan (SSP) is to describe past, present, and future activities undertaken to implement Environmental Restoration and Waste Management goals at the Portsmouth Gaseous Diffusion Plant (PORTS). The SSP is presented in sections emphasizing Environmental Restoration description of activities, resources, and milestones

Nonintrusive field experiments show different plant responses to warming and drought among sites, seasons, and species in a north-south European gradient

DEFF Research Database (Denmark)

Penuelas, J.; Gordon, C.; Llorens, L.

2004-01-01

-limited. In the water-stressed southern site, there was no increase in total aboveground plant biomass growth as expected since warming increases water loss, and temperatures in those ecosystems are already close to the optimum for photosynthesis. The southern site presented instead the most negative response...... a 15% increase in total aboveground plant biomass growth in the UK site. Both direct and indirect effects of warming, such as longer growth season and increased nutrient availability, are likely to be particularly important in this and the other northern sites which tend to be temperature...... to the drought treatment consisting of a soil moisture reduction at the peak of the growing season ranging from 33% in the Spanish site to 82% in The Netherlands site. In the Spanish site there was a 14% decrease in total aboveground plant biomass growth relative to control. Flowering was decreased by drought...

Phytoremediation potential and ecological and phenological changes of native pioneer plants from weathered oil spill-impacted sites at tropical wetlands.

Science.gov (United States)

Palma-Cruz, Felipe de J; Pérez-Vargas, Josefina; Rivera Casado, Noemí Araceli; Gómez Guzmán, Octavio; Calva-Calva, Graciano

2016-08-01

Pioneer native plant species from weathered oil spill-affected sites were selected to study their potential for phytoremediation on the basis of their ecological and phenological changes during the phytoremediation process. Experiments were conducted in field and in greenhouse. In field, native plants from aged oil spill-impacted sites with up 400 g of weathered petroleum hydrocarbons per kilogram soil were selected. In the impacted sites, the principal dominant plant species with potential for hydrocarbons removal were Cyperus laxus, Cyperus esculentus, and Ludwigia peploides. In greenhouse, the phenology of the selected plant species was drastically affected by the hydrocarbons level above 325 g total petroleum hydrocarbons (TPH) per kilogram soil after 2 years of phytoremediation of soils from the aged oil spill-impacted sites. From the phytoremediation treatments, a mix-culture of C. laxus, C. esculentus, and L. peploides in soil containing 325 g TPH/kg soil, from which 20.3 % were polyaromatic hydrocarbons (PAH) and 34.2 % were asphaltenes (ASF), was able to remove up 93 % of the TPH, while in unvegetated soil the TPH removal was 12.6 %. Furthermore, evaluation of the biodiversity and life forms of plant species in the impacted sites showed that phytoremediation with C. esculentus, alone or in a mix-culture with C. laxus and L. peploides, reduces the TPH to such extent that the native plant community was progressively reestablished by replacing the cultivated species resulting in the ecological recovery of the affected soil. These results demonstrate that native Cyperus species from weathered oil spill-affected sites, specifically C. esculentus and C. laxus, alone or in a mix-culture, have particular potential for phytoremediation of soils from tropical wetlands contaminated with weathered oil hydrocarbons.

A parasitic nematode releases cytokinin that controls cell division and orchestrates feeding site formation in host plants.

Science.gov (United States)

Siddique, Shahid; Radakovic, Zoran S; De La Torre, Carola M; Chronis, Demosthenis; Novák, Ondřej; Ramireddy, Eswarayya; Holbein, Julia; Matera, Christiane; Hütten, Marion; Gutbrod, Philipp; Anjam, Muhammad Shahzad; Rozanska, Elzbieta; Habash, Samer; Elashry, Abdelnaser; Sobczak, Miroslaw; Kakimoto, Tatsuo; Strnad, Miroslav; Schmülling, Thomas; Mitchum, Melissa G; Grundler, Florian M W

2015-10-13

Sedentary plant-parasitic cyst nematodes are biotrophs that cause significant losses in agriculture. Parasitism is based on modifications of host root cells that lead to the formation of a hypermetabolic feeding site (a syncytium) from which nematodes withdraw nutrients. The host cell cycle is activated in an initial cell selected by the nematode for feeding, followed by activation of neighboring cells and subsequent expansion of feeding site through fusion of hundreds of cells. It is generally assumed that nematodes manipulate production and signaling of the plant hormone cytokinin to activate cell division. In fact, nematodes have been shown to produce cytokinin in vitro; however, whether the hormone is secreted into host plants and plays a role in parasitism remained unknown. Here, we analyzed the spatiotemporal activation of cytokinin signaling during interaction between the cyst nematode, Heterodera schachtii, and Arabidopsis using cytokinin-responsive promoter:reporter lines. Our results showed that cytokinin signaling is activated not only in the syncytium but also in neighboring cells to be incorporated into syncytium. An analysis of nematode infection on mutants that are deficient in cytokinin or cytokinin signaling revealed a significant decrease in susceptibility of these plants to nematodes. Further, we identified a cytokinin-synthesizing isopentenyltransferase gene in H. schachtii and show that silencing of this gene in nematodes leads to a significant decrease in virulence due to a reduced expansion of feeding sites. Our findings demonstrate the ability of a plant-parasitic nematode to synthesize a functional plant hormone to manipulate the host system and establish a long-term parasitic interaction.

Predicting local distributions of erosion-corrosion wear sites for the piping in the nuclear power plant using CFD models

International Nuclear Information System (INIS)

Ferng, Y.M.

2008-01-01

The erosion-corrosion (E/C) wear is an essential degradation mechanism for the piping in the nuclear power plant, which results in the oxide mass loss from the inside of piping, the wall thinning, and even the pipe break. The pipe break induced by the E/C wear may cause costly plant repairs and personal injures. The measurement of pipe wall thickness is a useful tool for the power plant to prevent this incident. In this paper, CFD models are proposed to predict the local distributions of E/C wear sites, which include both the two-phase hydrodynamic model and the E/C models. The impacts of centrifugal and gravitational forces on the liquid droplet behaviors within the piping can be reasonably captured by the two-phase model. Coupled with these calculated flow characteristics, the E/C models can predicted the wear site distributions that show satisfactory agreement with the plant measurements. Therefore, the models proposed herein can assist in the pipe wall monitoring program for the nuclear power plant by way of concentrating the measuring point on the possible sites of severe E/C wear for the piping and reducing the measurement labor works

Determination of metallic elements in soils and plants in industrial and urban sites

Energy Technology Data Exchange (ETDEWEB)

Delearte, E; Nangniot, P; Impens, R

1973-01-01

The first phase of a program to study metals in soils and plants in industrial and urban sites is reported. The metals analyzed were copper, cobalt, nickel, zinc, lead, and cadmium. The soil samples were taken at increasing distances from potential emission sources with respect to dominant wind directions. Ubiquitous plants, such as Tussilago farfara L., Plantago major L., Mercurialis annua L., and Agrostis velgaris With. were used as samples for differential oscillopolarographic analyses. Soil samples taken around a zinc ore roasting plant showed very high zinc contents, and irregular distribution of cadmium and copper. Plant samples taken at different distances from the plant revealed rapid reduction of the copper, zinc, and cadmium levels with increasing distance. Very high concentrations of copper were found in plants around a petroleum refinery. Leaves of Aeer platanoides variety Schwedlerii in a town contained an average of 14.1 ppM copper, 0.7 ppM cobalt, 5.4 ppM nickel, 160 ppM zinc, 145 ppM lead, and 0.08 ppM cadmium, relative to the dry weight. The findings indicate that samples should be obtained over a period of sufficient length.

Rocky Flats Plant Site, Golden, Colorado. Volume I. Draft environmental impact statement

International Nuclear Information System (INIS)

1977-09-01

Two previous environmental statements have been issued for the Rocky Flats Plant site. One concerned a new plutonium recovery facility (WASH-1517, USAEC, January 1972); the second concerned land acquisition (WASH-1518, USAEC, April 1972). This document responds to those who indicated concerns and also ERDA's anticipated concerns about activities associated with the Rocky Flats Plant. Most concerns focus on two points including the Plant's involvement in the production of nuclear weapons and the Plant's handling of hazardous materials, particularly the radioactive element plutonium. The production of nuclear weapons, in which the Rocky Flats Plant maintains a vital role, will probably continue for as long as the world situation suggests that this country must have a strong defense. Operations at the Rocky Flats Plant have resulted in some plutonium being released to the environment, but evidence does not indicate that the amounts involved have presented any measurable hazard to human health. Ongoing improvements to the Plant's facilities and operational procedures are intended to preclude any recurrence of past releases. Despite these improvements, some public concern has resulted from past releases and the potential adverse effects from any possible future releases. This DEIS addresses that concern. It comments on past mishaps along with their causes and effects. It discusses current operations plus related costs and benefits to the region. Various alternatives to continuing present operations are explored, and the costs and benefits of the different options are compared

Computerization of off-site dose calculations at two nuclear power plants

International Nuclear Information System (INIS)

Lei, W.; Robertson, C.E.; Moore, G.T.; Rawls, B.E.; Sipp, J.R.

1988-01-01

The Brunswick Nuclear Project (BNP) consists of two boiling water reactors designed to generate a total net output of 1642 MWe. Unit 2 achieved commercial production in 1975, and Unit 1 began commercial operation in 1977. The Harris nuclear Project (HNP) is an 860 MWe pressurized water reactor that entered commercial operation in May of 1987. both plant sites are operated by Carolina Power and Light Company (CP and L). During January 1984, BNP replaced its older effluent technical specifications (part of the plant's original license) with the newer generation of Radiological Effluent Technical Specifications (RETS) mandated by the U.S. Nuclear Regulatory Commission. The RETS for HNP were integrated directly into this initial technical specifications. The initial version of the ODCM for BNP was drafted by a vendor and then extensively rewritten by the plant staff. The manual for HNP was drafted by CP and L corporate staff. At the outset, it was realized how impractical it would be to attempt to manually perform all of the dose calculations and keep the necessary records. The alternative-computerization-required extensive in-plant and corporate efforts to identify the computing resources (hardware) needed, create the software for ODCM implementation, and test, verify, validate, and document the software. This paper discusses these efforts

Radioactive Waste Disposal Pilot Plant concept for a New Mexico site

International Nuclear Information System (INIS)

Weart, W.D.

1976-01-01

Twenty years of investigation have shown that disposal of nuclear wastes in deep salt formations is the surest means of isolating these wastes from the biosphere for the extremely long period of time required. A large scale demonstration of this capability will soon be provided by a Radioactive Waste Disposal Pilot Plant (RWDPP) to be developed in southeastern New Mexico. Initially, the pilot plant will accept only ERDA generated waste; high level waste from the commercial power reactor fuel cycle will eventually be accommodated in the pilot plant and the initial RWDPP design will be compatible with this waste form. Selection of a specific site and salt horizon will be completed in June 1976. Conceptual design of the RWDPP and assessment of its environmental impact will be completed by June 1977. Construction is expected to start in 1978 with first waste accepted in 1982. The present concept develops disposal areas for all nuclear waste types in a single salt horizon about 800 meters deep. This single level can accommodate all low level and high level waste generated in the United States through the year 2010. A major constraint on the RWDPP design is the ERDA requirement that all waste be ''readily'' retrievable during the duration of pilot plant operation

Location sites for nuclear power plants and the public drinking water supplies

International Nuclear Information System (INIS)

1987-05-01

This report presents the results of a study by the Dutch RIWA- Working Group Nuclear Power Plants, of the possible effects of a nuclear-reactor melt-down accident upon the drinking-water supply in the Netherlands which is dependent on surface waters. The aim of this report is to contribute to the 're-consideration with regard to siting of nuclear power plants' of the Dutch government. In the case of a nuclear-reactor melt-down accident in the Netherlands or directly adjacent countries, surface waters destined for drinking-water production may be contaminated severely. The amount of contamination depends, among other things, upon the distance, wind direction, dry as well as wet deposition and the features of the place yielding drinking water. From calculations of contamination of surface waters in the case of open- supply build up it appears that the derived norm of the radionuclide cocktail may be exceeded for a period of weeks up to several months or even years. There are reasons to draw the same conclusion for supply build up in the dunes by means of surface infiltration in the dunes. A melt-down accident can cause very severe contamination. Also here it can be stated that, in the case of a calamity in the Netherlands or directly adjacent countries, a norm transgression may occur for weeks up to years. In view of the risks which nuclear power plants can hold for the drinking-water supply which depends upon surface-waters as basis element. Severe objections should be made with respect to the siting of nuclear power plants in the Netherlands unless the occurrence of melt-down accidents could be excluded. 11 refs.; 4 figs.; 7 tabs

Borehole geophysics in nuclear power plant siting

International Nuclear Information System (INIS)

Crosby, J.W.; Scott, J.D.

1979-01-01

Miniaturized borehole geophysical equipment designed for use in ground-water investigations can be adapted to investigations of nuclear power plant sites. This equipment has proved to be of value in preliminary and comprehensive studies of interior basins where thick sequences of Quaternary clastic sediment, occasionally with associated volcanic rocks, pose problems of stratigraphic correlation. The unconsolidated nature of the deposits generally requires that exploratory holes be cased, which ordinarily restricts the borehole geophysical studies to the radiation functions--natural gamma, gamma-gamma, neutron-gamma, and neutron-epithermal neutron logs. Although a single log response may be dominant in a given area, correlations derive from consideration of all log responses as a composite group. Because major correlations usually are based upon subtle differences in the physical properties of the penetrated sediment, high-resolution logging procedures are employed with some sacrifice of the quantitative perameters important to petroleum technology. All geophysical field data are recorded as hard copy and as digital information on punched paper tape

Demands and criteria for the site selection from the view of the power plant owners

International Nuclear Information System (INIS)

Beising, R.; Staebler, K.

1976-01-01

The methods as shown by the concrete example of the site provision plan for Baden-Wuerttemberg have proved extremely useful. The pragmatic method of site selection which ensures as little clash of interests as possible between the power plant and other preservation interests such as e.g. environment preservation, recreation areas, development axes, water economics is the only possible method for the densely populated areas of the Federal Republic. The numerous physical constraints in our Land only allow an optimisation of site search within the limited possibilities. (HP) [de

Decision analysis for the siting of nuclear power plants: the relevance of multiattribute utility theory

International Nuclear Information System (INIS)

Keeney, R.L; Nair, K.

1975-01-01

The necessity for improved decision making concerning the siting and licensing of major power facilities has been accelerated in the past decade by the increased environmental consciousness of the public and by the energy crisis. These problems are exceedingly complex due to their multiple objective nature, the many interest groups, the long-range time horizons, and the inherent uncertainties of the potential impacts of any decision. Along with the relatively objective economic and engineering concerns, clearly the more subjective factors involving safety, environmental, and social issues are crucial to the problem. Hence, the professional judgments and knowledge of experts in these areas should be utilized in analyses of siting decisions. Likewise, the preferences of the general public, as consumers, the utility companies, as builders and operators of power plant facilities, and environmentalists and the government must be accounted for in analyzing power plant siting and licensing issues. We advocate an approach for formally articulating the experts' judgments and the decision makers' preferences, both of which are clearly subjective, and processing these along with the more objective considerations in a logical manner to acquire the implications for decision making. The appropriateness and application of decision analysis for power plant location decisions is discussed and illustrated. Emphasis is placed on the assessment of the decision maker's preferences and tradeoffs concerning multiple objectives. (U.S.)

Eco-hydrology: Groundwater flow and site factors in plant ecology

Science.gov (United States)

Klijn, Frans; Witte, Jan-Philip M.

Résumé En écologie végétale, le site est un concept central. Un site, c'est l'endroit où une espèce végétale ou une communauté de plantes se développe le site assure un ensemble de conditions dans lesquelles elles vivent. Dans un matériau homogène à l'origine, l'écoulement gravitaire d'une nappe influence les conditions du site par l'intermédiaire de la distribution spatiale des nutriments et d'autres composés chimiques associés. Les remontées d'eau peuvent tout spécialement produire et maintenir les conditions du site essentielles pour différentes espèces et communautés de plantes relativement rares. Les écologues ont porté une attention accrue à ces remontées d'eau, en sorte qu'une coopération avec les hydrologues en a résulté, avec l'émergence d'une discipline propre, l'éco-hydrologie, à la limite des deux domaines scientifiques et liée au concept de site. Aux Pays-Bas, une classification des types d'eau, basée sur l'histoire de l'eau souterraine à proximité de la surface, a été mise en oeuvre pour constituer une base nationale de données géographiques sur les remontées d'eau d'intérêt écologique. Des analyses des correspondances des données de cette base, portant sur l'existence de certaines espèces de plantes, montrent que dans les sols sableux pauvres du Pléistocène la remontée d'eau explique très bien la présence de certaines espèces et communautés, alors que, dans les plaines fluviales et les régions de polders à sols argileux riches, l'influence de la remontée d'eau est masquée par l'importance des caractéristiques des sols. En conclusion donc, certaines espèces de plantes peuvent être utilisées comme des indicateurs de la remontée d'eau dans des diagnostiques et des levés de terrain rapides, mais à condition de prendre en permanence des précautions sur les limites de l'approche. Resumen En ecología botánica un concepto de gran importancia es el de emplazamiento, definido como el lugar que

Cold shock to aquatic organisms: guidance for power-plant siting, design, and operation

International Nuclear Information System (INIS)

Coutant, C.C.

1977-01-01

Problems of cold-shock damages to aquatic organisms have arisen at some condenser cooling-water discharges of thermal power stations when the warm-water releases have suddenly terminated. The basis for such damage lies in the exposure of resident organisms to a rapid decrease in temperature and a sustained exposure to low temperature that induces abnormal behavioral or physiological performance and often leads to death. Although some spectacular fish kills from cold shock have occurred, the present knowledge of the hydraulic and biological processes involved can provide guidance for the siting, design, and operation of power-plant cooling systems to minimize the likelihood of significant cold-shock effects. Preventing cold-shock damages is one consideration in minimizing overall environmental impacts of power-plant cooling and in balancing plant costs with environmental benefits

Long term developments in irradiated natural uranium processing costs. Optimal size and siting of plants

International Nuclear Information System (INIS)

Thiriet, L.

1964-01-01

The aim of this paper is to help solve the problem of the selection of optimal sizes and sites for spent nuclear fuel processing plants associated with power capacity programmes already installed. Firstly, the structure of capital and running costs of irradiated natural uranium processing plants is studied, as well as the influence of plant sizes on these costs and structures. Shipping costs from the production site to the plant must also be added to processing costs. An attempt to reach a minimum cost for the production of a country or a group of countries must therefore take into account both the size and the location of the plants. The foreseeable shipping costs and their structure (freight, insurance, container cost and depreciation), for spent natural uranium are indicated. Secondly, for various annual spent fuel reprocessing programmes, the optimal sizes and locations of the plants are determined. The sensitivity of the results to the basic assumptions relative to processing costs, shipping costs, the starting up year of the plant programme and the length of period considered, is also tested. - this rather complex problem, of a combinative nature, is solved through dynamic programming methods. - It is shown that these methods can also be applied to the problem of selecting the optimal sizes and locations of processing plants for MTR type fuel elements, related to research reactor programmes, as well as to future plutonium element processing plants related to breeder reactors. Thirdly, the case where yearly extraction of the plutonium contained in the irradiated natural uranium is not compulsory is examined; some stockpiling of the fuel is then allowed some years, entailing delayed processing. The load factor of such plants is thus greatly improved with respect to that of plants where the annual plutonium demand is strictly satisfied. By including spent natural uranium stockpiling costs an optimal rhythm of introduction and optimal sizes for spent fuel

Tolerance of transgenic canola plants (Brassica napus) amended with plant growth-promoting bacteria to flooding stress at a metal-contaminated field site

International Nuclear Information System (INIS)

Farwell, Andrea J.; Vesely, Susanne; Nero, Vincent; Rodriguez, Hilda; McCormack, Kimberley; Shah, Saleh; Dixon, D. George; Glick, Bernard R.

2007-01-01

The growth of transgenic canola (Brassica napus) expressing a gene for the enzyme 1-aminocyclopropane-1-carboxylate (ACC) deaminase was compared to non-transformed canola exposed to flooding and elevated soil Ni concentration, in situ. In addition, the ability of the plant growth-promoting bacterium Pseudomonas putida UW4, which also expresses ACC deaminase, to facilitate the growth of non-transformed and transgenic canola under the above mentioned conditions was examined. Transgenic canola and/or canola treated with P. putida UW4 had greater shoot biomass compared to non-transformed canola under low flood-stress conditions. Under high flood-stress conditions, shoot biomass was reduced and Ni accumulation was increased in all instances relative to low flood-stress conditions. This is the first field study to document the increase in plant tolerance utilizing transgenic plants and plant growth-promoting bacteria exposed to multiple stressors. - Using transgenic plants and plant growth-promoting bacteria as phytoremediation methods increased plant tolerance at a metal-contaminated field site under low flood conditions

WSSRAP chemical plant geotechnical investigations for the Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

International Nuclear Information System (INIS)

1990-12-01

This document has been prepared for the United states Department of Energy (DOE) Weldon Spring Site Remedial Action Project (WSSRAP) by the Project Management Contractor (PMC), which consists of MK-Ferguson Company (MKF) and Morrison Knudsen Corporation Environmental Services Group (MKES) with Jacobs Engineering Group (JEG) as MKF's predesignated subcontractor. This report presents the results of site geotechnical investigations conducted by the PMC in the vicinity of the Weldon Spring chemical plant and raffinate pits (WSCP/RP) and in potential on-site and off-site clayey material borrow sources. The WSCP/RP is the proposed disposal cell (DC) site. 39 refs., 24 figs., 12 tabs

Controlling engineering project changes for multi-unit, multi-site standardized nuclear power plants

International Nuclear Information System (INIS)

Randall, E.; Boddeker, G.; McGugin, H.; Strother, E.; Waggoner, G.

1978-01-01

Multibillioin dollar multiple nuclear power plant projects have numerous potential sources of engineering changes. The majority of these are internally generated changes, client generated changes, and changes from construction, procurement, other engineering organizations, and regulatory organizations. For multiunit, multisite projects, the use of a standardized design is cost effective. Engineering changes can then be controlled for a single standardized design, and the unit or site unique changes can be treated as deviations. Once an effective change procedure is established for change control of the standardized design, the same procedures can be used for control of unit or site unique changes

Application of microearthquake surveys in nuclear power plant siting

International Nuclear Information System (INIS)

1985-06-01

Earthquakes of magnitude less than 3 are generally referred to as microearthquakes. After an overview of the use of microearthquake survey in decisions related to the siting of nuclear power plants, the main aspects of a microearthquake survey network are discussed. The use of microearthquake surveys in investigating problems related to near-field (floating) earthquakes is also discussed. The discussion is centered on the practical application of such a survey leading from objectives and limitations over to planning, instrumentation, operation, maintenance, processing of the data, and interpretation and reporting of the results. An appendix entitled Earthquake Magnitude gives useful background information for definitions of different types of magnitude and their calculation using the records from microearthquake surveys

Site selection experience for a new low-level radioactive waste storage/disposal facility at the Savannah River Plant

International Nuclear Information System (INIS)

Towler, O.A.; Cook, J.R.; Helton, B.D.

1985-10-01

Preliminary performance criteria and site selection guides specific to the Savannah River Plant, were developed for a new low-level radioactive waste storage/disposal facility. These site selection guides were applied to seventeen potential sites identified at SRP. The potential site were ranked based on how well they met a set of characteristics considered important in site selection for a low-level radioactive waste disposal facility. The characteristics were given a weighting factor representing its relative importance in meeting site performance criteria. A candidate site was selected and will be the subject of a site characterization program

Legal consequences of the special development plan 'power plant sites' on regional planning and on guidelines for building plans

International Nuclear Information System (INIS)

1978-01-01

The Special Development Plan 'Power plant sites' was made compulsory by the regulation given by the Land government in Juli 1976. For extending the energy supply system this Special Development Plan intends to provide a sufficient amount of power plant sites suitably located with regard to present and future consumption centres and permitting a cooling by means of river water while safeguarding the interests of water resources policy. The Special Development Plan established in accordance with the articles 25 and 27 of the planning law of the Land lays down that 14 specified areas are to be kept free from utilization purposes which could be opposed to the realization of power plant projects. Thus the securing of these (potential) sites has become an objective of area planning and planning of the Land in the sense of article 5 paragraph 4 of the Federal law on area planning. (orig./HP) [de

Dose commitments due to radioactive releases from nuclear power plant sites in 1989

International Nuclear Information System (INIS)

Baker, D.A.

1993-02-01

Population and individual radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1989. Fifty-year dose commitments for a one-year exposure from both liquid and atmospheric releases were calculated for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 72 reactor sites. This report tabulates the results of these calculations, showing the dose commitments for both water and airborne pathways for each age group and organ. Also included for each of the sites is an estimate of individual doses which are compared with 10 CFR Part 50, Appendix I design objectives. The total collective dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 14 person-rem to a low of 0.005 person-rem for the sites with plants in operation and producing power during the year. The arithmetic mean was 1.2 person-rem. The total population dose for all sites was estimated at 84 person-rem for the 140 million people considered at risk. The individual dose commitments estimated for all sites were below the Appendix I design objectives

Dose commitments due to radioactive releases from nuclear power plant sites in 1989

Energy Technology Data Exchange (ETDEWEB)

Baker, D.A. (Pacific Northwest Lab., Richland, WA (United States))

1993-02-01

Population and individual radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1989. Fifty-year dose commitments for a one-year exposure from both liquid and atmospheric releases were calculated for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 72 reactor sites. This report tabulates the results of these calculations, showing the dose commitments for both water and airborne pathways for each age group and organ. Also included for each of the sites is an estimate of individual doses which are compared with 10 CFR Part 50, Appendix I design objectives. The total collective dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 14 person-rem to a low of 0.005 person-rem for the sites with plants in operation and producing power during the year. The arithmetic mean was 1.2 person-rem. The total population dose for all sites was estimated at 84 person-rem for the 140 million people considered at risk. The individual dose commitments estimated for all sites were below the Appendix I design objectives.

Waset Isolation Pilot Plant Annual Site Environmental Report for 2006

Energy Technology Data Exchange (ETDEWEB)

Washington Regulatory and Environmental Services; Washington TRU Solutions LLC

2007-09-26

The purpose of the Waste Isolation Pilot Plant Annual Site Environmental Report for 2006 (ASER) is to provide information required by U.S. Department of Energy (DOE) Order 231.1A, Environment, Safety, and Health Reporting. Specifically, the ASER presents summary environmental data that: (a) Characterize site environmental management performance; (b) Summarize environmental occurrences and responses reported during the calendar year; (c) Confirm compliance with environmental standards and requirements; and (d) Highlight significant facility programs and efforts. The DOE Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) maintain and preserve the environmental resources at the WIPP site. DOE Order 231.1A; DOE Order 450.1, Environmental Protection Program; and DOE Order 5400.5, Radiation Protection of the Public and Environment, require that the affected environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This report was prepared in accordance with DOE Order 231.1A. This order requires that DOE facilities submit an ASER to the DOE Headquarters Office of the Assistant Secretary for Environment, Safety, and Health. The WIPP Hazardous Waste Facility Permit (HWFP) (No. NM4890139088-TSDF [treatment, storage, and disposal facility]) further requires that the ASER be provided to the New Mexico Environment Department (NMED).

Reassessment of selected factors affecting siting of Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Davis, R.E.; Hanson, A.L.; Mubayi, V.; Nourbakhsh, H.P.

1997-02-01

Brookhaven National Laboratory has performed a series of probabilistic consequence assessment calculations for nuclear reactor siting. This study takes into account recent insights into severe accident source terms and examines consequences in a risk based format consistent with the quantitative health objectives (QHOs) of the NRC`s Safety Goal Policy. Simplified severe accident source terms developed in this study are based on the risk insights of NUREG-1150. The results of the study indicate that both the quantity of radioactivity released in a severe accident as well as the likelihood of a release are lower than those predicted in earlier studies. The accident risks using the simplified source terms are examined at a series of generic plant sites, that vary in population distribution, meteorological conditions, and exclusion area boundary distances. Sensitivity calculations are performed to evaluate the effects of emergency protective action assumptions on the risk of prompt fatality and latent cancers fatality, and population relocation. The study finds that based on the new source terms the prompt and latent fatality risks at all generic sites meet the QHOs of the NRC`s Safety Goal Policy by margins ranging from one to more than three orders of magnitude. 4 refs., 17 figs., 24 tabs.

Waset Isolation Pilot Plant Annual Site Environmental Report for 2006

International Nuclear Information System (INIS)

2007-01-01

The purpose of the Waste Isolation Pilot Plant Annual Site Environmental Report for 2006 (ASER) is to provide information required by U.S. Department of Energy (DOE) Order 231.1A, Environment, Safety, and Health Reporting. Specifically, the ASER presents summary environmental data that: (a) Characterize site environmental management performance; (b) Summarize environmental occurrences and responses reported during the calendar year; (c) Confirm compliance with environmental standards and requirements; and (d) Highlight significant facility programs and efforts. The DOE Carlsbad Field Office (CBFO) and Washington TRU Solutions LLC (WTS) maintain and preserve the environmental resources at the WIPP site. DOE Order 231.1A; DOE Order 450.1, Environmental Protection Program; and DOE Order 5400.5, Radiation Protection of the Public and Environment, require that the affected environment at and near DOE facilities be monitored to ensure the safety and health of the public and the environment. This report was prepared in accordance with DOE Order 231.1A. This order requires that DOE facilities submit an ASER to the DOE Headquarters Office of the Assistant Secretary for Environment, Safety, and Health. The WIPP Hazardous Waste Facility Permit (HWFP) (No. NM4890139088-TSDF [treatment, storage, and disposal facility]) further requires that the ASER be provided to the New Mexico Environment Department (NMED).

Site organization and site arrangement

International Nuclear Information System (INIS)

Boissonnet, B.; Macqueron, J.F.

1976-01-01

The present paper deals with criteria for the choice of a production unit or power plant site, the organization and development of a site in terms of its particular characteristics and takes into account personnel considerations in site organizations as well as the problem of integrating the architecture into the environment. (RW) [de

78 FR 8587 - American Showa, Inc.; Blanchester Plant, Including On-Site Leased Workers From Adecco and Sims...

Science.gov (United States)

2013-02-06

....; Blanchester Plant, Including On-Site Leased Workers From Adecco and Sims Bros., Inc.; Blanchester, OH; Amended... workers from Sims Bros., Inc. were working on-site at the subject firm during the relevant period and that the services supplied by Sims Bros., Inc. were related to the production of gear boxes (and parts...

Stranded Fuel, Orphan Sites, Dead Plants: Transportation Planning Considerations After the BRC Report - 13393

Energy Technology Data Exchange (ETDEWEB)

Thrower, Alex W. [The Thrower Group LLC, Richmond, VA (United States)

2013-07-01

The author explores transportation, packaging and storage questions related to a primary recommendation of the Blue Ribbon Commission on America's Nuclear Future; i.e., that fuel from shutdown plants be removed to consolidated storage as soon as possible to enable final decommissioning and beneficial re-use of those sites. The paper discusses the recommendations of the BRC, the implications and challenges that implementing those recommendations present, and provides recommended solutions for beginning the multi-year planning, coordination, material acquisition, and communications processes that will be needed to move fuel from shutdown plants when a destination site becomes available. Removal of used nuclear fuel from shutdown reactor sites (which are serving no other purpose other than storing SNF and GTCC, at considerable expense) was a central recommendation of the BRC, for a number of reasons. This recommendation was one of the most widely acclaimed that the Commission put forward. However, there are significant challenges (such as availability of fuel canister overpacks, lack of infrastructure, handling constraints and others) that will need to be addressed, apart from the critically important identification of a suitable and workable storage destination site. Resolving these logistical challenges will need to begin even before a destination site is identified, given the long lead-times required for planning and procurement. Based on information available today, it is possible to make informed predictions about what will be needed to modify existing contractual arrangements with utilities, address equipment and infrastructure needs, and begin working with states, tribes and local governments to start initial preparation needs. If DOE, working with industry and other experienced parties, can begin planning and acquisition activities in the near term, overall schedule risk can be reduced and potential cost avoidance achieved. The most immediate benefit will

Stranded Fuel, Orphan Sites, Dead Plants: Transportation Planning Considerations After the BRC Report - 13393

International Nuclear Information System (INIS)

Thrower, Alex W.

2013-01-01

The author explores transportation, packaging and storage questions related to a primary recommendation of the Blue Ribbon Commission on America's Nuclear Future; i.e., that fuel from shutdown plants be removed to consolidated storage as soon as possible to enable final decommissioning and beneficial re-use of those sites. The paper discusses the recommendations of the BRC, the implications and challenges that implementing those recommendations present, and provides recommended solutions for beginning the multi-year planning, coordination, material acquisition, and communications processes that will be needed to move fuel from shutdown plants when a destination site becomes available. Removal of used nuclear fuel from shutdown reactor sites (which are serving no other purpose other than storing SNF and GTCC, at considerable expense) was a central recommendation of the BRC, for a number of reasons. This recommendation was one of the most widely acclaimed that the Commission put forward. However, there are significant challenges (such as availability of fuel canister overpacks, lack of infrastructure, handling constraints and others) that will need to be addressed, apart from the critically important identification of a suitable and workable storage destination site. Resolving these logistical challenges will need to begin even before a destination site is identified, given the long lead-times required for planning and procurement. Based on information available today, it is possible to make informed predictions about what will be needed to modify existing contractual arrangements with utilities, address equipment and infrastructure needs, and begin working with states, tribes and local governments to start initial preparation needs. If DOE, working with industry and other experienced parties, can begin planning and acquisition activities in the near term, overall schedule risk can be reduced and potential cost avoidance achieved. The most immediate benefit will

Development of plant status display system for on-site educational training system

International Nuclear Information System (INIS)

Yoshimura, Seiichi; Fujimoto, Junzo; Okamoto, Hisatake; Tsunoda, Ryohei; Watanabe, Takao; Masuko, Jiro.

1986-01-01

The purpose of this system is to make easy the comprehension of the facility and dynamics of nuclear power plants. This report describes the tendency and future position of how the educational training system should be, and furthermore describes the experiment. Main results are as follows. 1. The present status and the future tendency of educational training system for nuclear power plant operators. CAI (Computer Assisted Instruction) system has following characteristics. (1) It is easy to introduce plant specific characteristics to the educational training. (2) It is easy to execute the detailed training for the compensation of the full-scale simulator. 2. Plant status display system for on-site educational training system. The fundamental function of the system is as follows. (1) It has 2 CRT displays and voice output devices. (2) It has easy manupulation type of man-machine interface. (3) It has the function for the evaluation of the training results. 3. The effectiveness of this system. The effectiveness evaluation test has been carried out by using this system actually. (1) This system has been proved to be essentially effective and some improvements for the future utilization has been pointed out. (2) It should be faster when the CRT displayes are changed, and it should have the explanation function when the plant transients are displayed. (author)

Preparation of substituting seaweed field mounds accompanying site preparation for No.3 plant in Ikata Nuclear Power Station

International Nuclear Information System (INIS)

Ishihara, Hisashi; Oshima, Teruhiko; Fujisaki, Yuichi; Saeki, Taketoshi

1987-01-01

Shikoku Electric Power Co., Inc. is constructing No.3 plant adjacently to No.1 and No.2 plants in operation in Ikata Nuclear Power Station. In the coastal area of Iyo-nada, many seaweed fields are distributed, which are important biologically and for fishery. In the works of site preparation for No.3 plant, a part of the site is created by reclamation of sea area, therefore the natural seaweed fields in the area disappear. From the viewpoint of various circumstances and environment preservation, it was decided to create about 60,000 m 2 of seaweed field mounds on the seabed around the site as the substitute for disappearing natural seaweed fields. The Seaweed Field Study Group composed of the men of learning and experience was organized to obtain the guidance on the possibility of creating artificial seaweed fields, the techniques for creation and the effect on environment accompanying the creation of mounds. The creation works were started in October, 1985, and are in progress smoothly utilizing effectively the stones and rocks cut in the site preparation works. The topographic and geological features, sea conditions, the present state of seaweed fields, the experiment on creating artificial seaweed fields, the design and construction of mounds and others are reported. (Kako, I.)

A study of feasibility, design and cost of excavations for underground siting of nuclear power plants

International Nuclear Information System (INIS)

1976-02-01

A study conducted for the State Power Board on underground siting of nuclear power plants is presented. The report is divided into two chapters, both concerning the technical aspects of large underground openings. The first chapter gives a brief general survey of the problems involved, and the second outlines the technical aspects of a PWR project at a specific site. Details are given in 8 appendices and arrangement drawings. The project differs from conventional hydroelectric excavation schemes mainly in the fact that the spherical reactor containment requires a vault of 60m free span, and the turbine hall a cylindrical vault of 45m span, both of which exceed any span hitherto built for similar purposes. This requires a comparatively wide extrapolation of tested and available experience in underground excavations for permanent civil use. To what extent and under what circumstances such extrapolation is tenable must be tested in practice, preferably in a specially controlled prototype test. However the study indicates that conventional nuclear power plants can be sited underground when the topography and rock conditions are suitable. A 1000-2000 MW conventional plant adapted for underground siting will require large span caverns, tunnels and shafts, totalling about 1.0 mill. cubic metres of underground excavation. In addition access and cooling water tunnels, depending on the location, will require 0.2-0.5 mill. cubic metres of tunnel excavations. The excavations and support work can be completed within a construction time of about 2 1/2 years at an estimated total cost of 215 mill. Norwegian kroner (1975 value). (JIW)

Sustainable siting procedure of small hydroelectric plants: The Greek experience

International Nuclear Information System (INIS)

Tsoutsos, Theocharis; Maria, Efpraxia; Mathioudakis, Vassilis

2007-01-01

This paper aims to present the procedure under which a sustainable plant, like a small hydroelectric plant (SHP), can be installed and deployed, especially in countries with complicated administrative and legislative systems. Those must be defined by the rules that characterize sustainable spatial planning, which aims at the environmental protection, the insurance of better living conditions and finally at the economic development within the frame of the principle of sustainability and its three basic dimensions: social, economical and environmental. The main principles of spatial planning are accepted from the jurisprudence of the Hellenic Council of State, either as an appropriate condition for the protection of important ecosystems or as specific expression of the principle of prevention of environmental damage. In this framework it is accepted that the development is experienced, initially to a total and general planning, whose essential part is the assessment and modification of distributed land uses. Besides, the main characteristics of the siting of SHPs and the criteria demanded for their smooth integration and operation are presented

Population dose commitments due to radioactive releases from nuclear power plant sites in 1983

International Nuclear Information System (INIS)

Baker, D.A.; Peloquin, R.A.

1987-04-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1983. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 52 sites. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each of the sites is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 45 person-rem to a low of 0.002 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 3 person-rem. The total population dose for all sites was estimated at 170 person-rem for the 100 million people considered at risk

Variable Isotopic Compositions of Host Plant Populations Preclude Assessment of Aphid Overwintering Sites

Directory of Open Access Journals (Sweden)

Michael S. Crossley

2017-12-01

Full Text Available Soybean aphid (Aphis glycines Matsumura is a pest of soybean in the northern Midwest whose migratory patterns have been difficult to quantify. Improved knowledge of soybean aphid overwintering sites could facilitate the development of control efforts with exponential impacts on aphid densities on a regional scale. In this preliminary study, we explored the utility of variation in stable isotopes of carbon and nitrogen to distinguish soybean aphid overwintering origins. We compared variation in bulk 13C and 15N content in buckthorn (Rhamnus cathartica L. and soybean aphids in Wisconsin, among known overwintering locations in the northern Midwest. Specifically, we looked for associations between buckthorn and environmental variables that could aid in identifying overwintering habitats. We detected significant evidence of correlation between the bulk 13C and 15N signals of soybean aphids and buckthorn, despite high variability in stable isotope composition within and among buckthorn plants. Further, the 15N signal in buckthorn varied predictably with soil composition. However, lack of sufficient differentiation of geographic areas along axes of isotopic and environmental variation appears to preclude the use of carbon and nitrogen isotopic signals as effective predictors of likely aphid overwintering sites. These preliminary data suggest the need for future work that can further account for variability in 13C and 15N within/among buckthorn plants, and that explores the utility of other stable isotopes in assessing likely aphid overwintering sites.

Waste Isolation Pilot Plant site environmental report for calendar year 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

US Department of Energy (DOE) Order 5400.1 General Environmental Protection Program, requires each DOE facility that conducts significant environmental protection programs to prepare an Annual Site Environmental Report (ASER). The purpose of the ASER is to summarize environmental data in order to characterize site environmental management performance, to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts. This ASER not only documents the required data, it also documents new and continued monitoring and compliance activities during the 1994 calendar year. Data contained in this report are derived from those monitoring programs directed by the Waste Isolation Pilot Plant (WIPP) Environmental Monitoring Plan (EMP) (DOE/WIPP 94-024). The EMP defines a comprehensive set of parameters that must be monitored to detect potential impacts to the environment and to establish baseline measurements for future environmental evaluations. Surface water, groundwater, air, soil, and biotics are monitored for radiological and nonradiological activity levels. The baseline radiological surveillance program covers the broader geographic area that encompasses nearby ranches, villages, and cities. Nonradiological studies focus on the area immediately surrounding the WIPP site.

Waste Isolation Pilot Plant site environmental report for calendar year 1994

International Nuclear Information System (INIS)

1995-06-01

US Department of Energy (DOE) Order 5400.1 General Environmental Protection Program, requires each DOE facility that conducts significant environmental protection programs to prepare an Annual Site Environmental Report (ASER). The purpose of the ASER is to summarize environmental data in order to characterize site environmental management performance, to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts. This ASER not only documents the required data, it also documents new and continued monitoring and compliance activities during the 1994 calendar year. Data contained in this report are derived from those monitoring programs directed by the Waste Isolation Pilot Plant (WIPP) Environmental Monitoring Plan (EMP) (DOE/WIPP 94-024). The EMP defines a comprehensive set of parameters that must be monitored to detect potential impacts to the environment and to establish baseline measurements for future environmental evaluations. Surface water, groundwater, air, soil, and biotics are monitored for radiological and nonradiological activity levels. The baseline radiological surveillance program covers the broader geographic area that encompasses nearby ranches, villages, and cities. Nonradiological studies focus on the area immediately surrounding the WIPP site

Former manufactured gas plants of Missouri: 19th century enigmas of today's site and waste characterization

International Nuclear Information System (INIS)

Hatheway, A.W.; Anderson, D.R.

1993-01-01

Missouri's first gas works began operation in 1845 (St. Louis). By 1900, gas works operated in many northern-Missouri coal belt towns, major cities, and Hannibal and Cape Girardeau (Mississippi River supply). Today's 40-odd former manufactured gas plant (FMPGs) sites are fiscal nightmares for parent utility companies; all hazardous waste groups are prevalent to the plants. Tar residuals may migrate along/through geologic anomalies. Tar-water emulsions typically were disposed in tar wells or nearby drainages or many times plumbed directly into sewers, which typically leaked into the environment at unpredictable down gradient locations. Just as well site geologic characteristics and current groundwater usage may render FMPGs relatively harmless from the human exposure standpoint. Geologic deduction, photo interpretation, careful subsurface exploration and engineering geophysics can locate hot spots and delimit contaminant migration. Many types of historic documents chronicle changes in plant character and equipment, as well as mode of operation. Without such details, mistakes in characterization are likely and errors in risk assessment and selection of remedial technologies are possible

Minutes and group memories from all NERBC/USGS-RPA power plant siting task force meetings through October, 1980. Appendix

International Nuclear Information System (INIS)

1980-11-01

The New England River Basins Commission/United States Geological Survey-Resource Planning Analysis Office (NERBC/USGS-RPA) Power Plant Siting Task Force has formerly met seven times between July 1979 and August 1980. At the first meeting on July 13, 1979, the members agreed that there were many problems with the current process of selecting sites for power plants in New England, and that they would work by consensus to find solutions for these problems. At the second meeting on October 19, 1979, NERBC staff presented information on the site selection and approval processes in New England. The Task Force began a preliminary discussion of problems in these processes, and agreed that the initial scope of work of the Task Force would focus on issues in site selection. At the third meeting on January 18, 1980, the Task Force began initial discussions in three areas: imperfections in the site selection process, stakeholders in the site selection process, and principles to guide solutions to the problems in site selection. On March 7, 1980, at the fourth meeting, the Task Force continued discussions on imperfections, stakeholders, and principles. At the fifth meeting on May 2, 1980, the Task Force reached a wide range of agreements on the difficulties encountered in the site selection process and on the principles guiding problem solving in site selection. At the sixth meeting on May 29, 1980, the Task Force focused on solutions to the problems identified at earlier meetings. Groups of Task Force members constructed eight different scenarios describing alternative power plant siting processes. In July 1980, the Task Force met for the seventh time and refined the eight scenarios, paring them down to five. An attempt was made to develop two scenarios using the common elements from the five. One of these two graphic models was based on government involvement in the site selection process, and the other was based on stakeholder involvement in the process

Solvent extraction for remediation of manufactured gas plant sites

International Nuclear Information System (INIS)

Luthy, R.G.; Dzombak, D.A.; Peters, C.; Ali, M.A.; Roy, S.B.

1992-12-01

This report presents the results of an initial assessment of the feasibility of solvent extraction for removing coal tar from the subsurface or for treating contaminated soil excavated at manufactured gas plant (MGP) sites. In situ solvent extraction would involve injection, recovery, and reclamation for reinjection of an environmentally-benign, water-miscible solvent. Accelerated dissolution and removal of coaltar from the subsurface might be desirable as a remedial approach if excavation is not practical (e.g., the site underlies facilities in current use), direct pumping of coal tar is ineffective, and bioremediation is not feasible because of the presence of high concentrations of coal tar. Both laboratory experiments and engineering evaluations were performed to provide a basis for the initial feasibility assessment. Laboratory work included identification and evaluation of promising solvents, measurement of fundamental properties of coal tar-solvent-water systems, and measurement of rates of dissolution of coal tar in porous media into flowing solvent-water solutions. Engineering evaluations involved identification of common hydrogeologic features and contaminant distributions at MGP sites, and identification and evaluation of possible injection-recovery well deployment schemes. A coupled flow-chemistry model was developed for simulation of the in situ process and evaluation of the well deployment schemes. Results indicate that in situsolvent extraction may be able to recover a significant amount of coal tar from the subsurface within a reasonable time frame (on the order of one year or so) provided that subsurface conditions are conducive to process implementation. Some important implementation issues remain to be addressed

Model calculations of the influence of population distribution on the siting of nuclear power plants

International Nuclear Information System (INIS)

Nielsen, F.; Walmod-Larsen, O.

1984-02-01

This report was prepared for a working group established in April 1981 by the Danish Environmental Protection Agency with the task of investigating siting problems of nuclear power stations in Denmark. The purpose of the working group was to study the influence of the population density around a site on nuclear power safety. The importance of emergency planning should be studied as well. In this model study two specific accident sequences were simulated on a 1000 MWe nuclear power plant. The plant was assumed to be placed in the center of two different model population distributions. The concequences for the two population distributions from the two accidents were calculated for the most frequent weather conditions. Doses to individuals were calculated for the bone marrow, lungs, gastrointestinal tract, thyroidea and for the whole body. The collective whole body doses were also calculated for the two populations considered. (author)

Rooting depths of plants on low-level waste disposal sites

International Nuclear Information System (INIS)

Foxx, T.S.; Tierney, G.D.; Williams, J.M.

1984-11-01

In 1981-1982 an extensive bibliographic study was done to reference rooting depths of native plants in the United States. The data base presently contains 1034 different rooting citations with approximately 12,000 data elements. For this report, data were analyzed for rooting depths related to species found on low-level waste (LLW) sites at Los Alamos National Laboratory. Average rooting depth and rooting frequencies were determined and related to present LLW maintenance. The data base was searched for information on rooting depths of 53 species found on LLW sites at Los Alamos National Laboratory. The study indicates 12 out of 13 grasses found on LLW sites root below 91 cm. June grass [Koeleria cristata (L.) Pers.] (76 cm) was the shallowest rooting grass and side-oats grama [Bouteloua curtipendula (Michx.) Torr.] was the deepest rooting grass (396 cm). Forbs were more variable in rooting depths. Indian paintbrush (Castelleja spp.) (30 cm) was the shallowest rooting forb and alfalfa (Medicago sativa L.) was the deepest (>3900 cm). Trees and shrubs commonly rooted below 457 cm. The shallowest rooting tree was elm (Ulmus pumila L.) (127 cm) and the deepest was one-seed juniper [Juniperus monosperma (Engelm) Sarg.] (>6000 cm). Apache plume [Fallugia paradoxa (D. Don) Endl.] rooted to 140 cm, whereas fourwing saltbush [Atriplex canecens (Pursh) Nutt.] rooted to 762 cm

Summary of site-characterization studies conducted from 1983 through 1987 at the Waste Isolation Pilot Plant (WIPP) site, southeastern New Mexico

International Nuclear Information System (INIS)

Lappin, A.R.

1988-01-01

The Waste Isolation Pilot Plant (WIPP) is being excavated at a depth of approximately 655 m in bedded halites. Site-characterization activities at the WIPP site began in 1976. Characterization activities since 1983 have had the objective of updating the conceptual model for the geologic and hydrologic behavior of the WIPP site and vicinity. This paper discusses aspects of the general conceptual model significant to both site characterization and performance assessment. The geological and hydrologic behavior of the WIPP site and vicinity is transient, and has been transient since at least deposition of the Permian Salado Formation containing the underground workings of the WIPP facility. The Salado Formation deforms regionally in response to gravity, but is very low in permeability, except within approximately two meters of the WIPP facility. The Culebra Dolomite Member of the Rustler Formation dominates the hydrology at the WIPP site. Hydrologic measurements, geologic studies, major-element and minor-element distributions in Culebra fluids, and the results of isotopic studies (stable-isotope, radiocarbon, uranium-disequilibrium, and 87 Sr/ 86 Sr) are consistent with the interpretations that, although the Culebra dominates flow within the Rustler at the WIPP site and Rustler karst is not present, there has been limited vertical fluid movement within the Rustler and between the Rustler and the overlying Dewey Lake Red Beds

Uptake of heavy metals by Typha capensis from wetland sites polluted by effluent from mineral processing plants: implications of metal-metal interactions.

Science.gov (United States)

Zaranyika, M F; Nyati, W

2017-10-01

The aim of the present work was to demonstrate the existence of metal-metal interactions in plants and their implications for the absorption of toxic elements like Cr. Typha capensis , a good accumulator of heavy metals, was chosen for the study. Levels of Fe, Cr, Ni, Cd, Pb, Cu and Zn were determined in the soil and roots, rhizomes, stems and leaves of T. capensis from three Sites A, B and C polluted by effluent from a chrome ore processing plant, a gold ore processing plant, and a nickel ore processing plant, respectively. The levels of Cr were extremely high at Site A at 5415 and 786-16,047 μg g -1 dry weight in the soil and the plant, respectively, while the levels of Ni were high at Site C at 176 and 24-891 μg g -1 in the soil and the plant, respectively. The levels of Fe were high at all three sites at 2502-7500 and 906-13,833 μg g -1 in the soil and plant, respectively. For the rest of the metals, levels were modest at 8.5-148 and 2-264 μg g -1 in the soil and plant, respectively. Pearson's correlation analysis confirmed mutual synergistic metal-metal interactions in the uptake of Zn, Cu, Co, Ni, Fe, and Cr, which are attributed to the similarity in the radii and coordination geometry of the cations of these elements. The implications of such metal-metal interactions (or effects of one metal on the behaviour of another) on the uptake of Cr, a toxic element, and possible Cr detoxification mechanism within the plant, are discussed.

Waste Isolation Pilot Plant Site Environmental Report for calendar year 1989

International Nuclear Information System (INIS)

1989-01-01

This is the 1989 Site Environmental Report (SER) for the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. The WIPP is a government owned and contractor-operated facility. The WIPP project is operated by Westinghouse Electric Corporation for the US Department of Energy (DOE). The mission of the WIPP is to provide a research and development facility to demonstrate the safe disposal of transuranic (TRU) waste generated by the defense activities of the US Government. This report provides a comprehensive description of environmental activities at the WIPP during calendar year 1989. The WIPP facility will not receive waste until all concerns affecting opening the WIPP are addressed to the satisfaction of the Secretary of Energy. Therefore, this report describes the status of the preoperational activities of the Radiological Environmental Surveillance (RES) program, which are outlined in the Radiological Baseline Program for the Waste Isolation Pilot Plant (WTSD-TME-057). 72 refs., 13 figs., 20 tabs

Paducah Gaseous Diffusion Plant Annual Site Environmental Report summary for 1993

International Nuclear Information System (INIS)

1994-11-01

This report contains summaries of the environmental programs at Paducah Gaseous Diffusion Plant, environmental monitoring and the results, and the impact of operations on the environment and the public for 1993. The environmental monitoring program at Paducah includes effluent monitoring and environmental surveillance. Effluent monitoring is measurement of releases as they occur. Contaminants are released through either airborne emissions or liquids discharged from the plant. These releases occur as part of normal site operations, such as cooling water discharged from the uranium enrichment cascade operations or airborne releases from ventilation systems. In the event of system failure, this monitoring provides timely warning so that corrective action can be taken before releases reach an unsafe level. Environmental surveillance tracks the dispersion of materials into the environment after they have been released. This involves the collection of samples from various media, such as water, soil, vegetation, and food crops, and the analysis of these samples for certain radionuclides, chemicals, and metals

Portsmouth Gaseous Diffusion Plant Annual Site Environmental Report summary for 1993

International Nuclear Information System (INIS)

1994-11-01

This report contains summaries of the environmental programs at Paducah Gaseous Diffusion Plant, environmental monitoring and the results, and the impact of operations on the environment and the public for 1993. The environmental monitoring program at Paducah includes effluent monitoring and environmental surveillance. Effluent monitoring is measurement of releases as they occur. Contaminants are released through either airborne emissions or liquids discharged from the plant. These releases occur as part of normal site operations, such as cooling water discharged from the uranium enrichment cascade operations or airborne releases from ventilation systems. In the event of system failure, this monitoring provides timely warning so that corrective action can be taken before releases reach an unsafe level. Environmental surveillance tracks the dispersion of materials into the environment after they have been released. This involves the collection of samples from various media, such as water, soil, vegetation, and food crops, and the analysis of these samples for certain radionuclides, chemicals, and metals

Evaluation of utility monitoring and preoperational hydrothermal modeling at three nuclear power plant sites

International Nuclear Information System (INIS)

Marmer, G.J.; Policastro, A.J.

1977-01-01

This paper evaluates the preoperational hydrothermal modeling and operational monitoring carried out by utilities as three nuclear-power-plant sites using once-through cooling. Our work was part of a larger study to assess the environmental impact of operating plants for the Nuclear Regulatory Commission (NRC) and the suitability of the NRC Environmental Technical Specifications (Tech Specs) as set up for these plants. The study revealed that the plume mappings at the Kewaunee, Zion, and Quad Cities sites were generally satisfactory in terms of delineating plume size and other characteristics. Unfortunately, monitoring was not carried out during the most critical periods when largest plume size would be expected. At Kewaunee and Zion, preoperational predictions using analytical models were found to be rather poor. At Kewaunee (surface discharge), the Pritchard Model underestimated plume size in the near field, but grossly overestimated the plume's far-field extent. Moreover, lake-level variations affected plume dispersion, yet were not considered in preoperational predictions. At Zion (submerged discharge) the Pritchard Model was successful only in special, simple cases (single-unit operation, no stratification, no reversing currents, no recirculation). Due to neglect of the above-mentioned phenomena, the model underpredicted plume size. At Quad Cities (submerged discharge), the undistorted laboratory model predicted plume dispersion for low river flows. These low flow predictions appear to be reasonable extrapolations of the field data acquired at higher flows

Plant hydraulic strategies and their variability at high latitudes: insights from a southern Canadian boreal forest site

Science.gov (United States)

Pappas, C.; Matheny, A. M.; Maillet, J.; Baltzer, J. L.; Stephens, J.; Barr, A.; Black, T. A.; Sonnentag, O.

2016-12-01

Boreal forests cover about one third of the world's forested area with a large part of the boreal zone located in Canada. These high-latitude ecosystems respond rapidly to environmental changes. Plant water stress and the resulting drought-induced mortality has been recently hypothesised as a major driver of forest changes in western Canada. Although boreal forests often exhibit low floristic complexity, local scale abiotic heterogeneities may lead to highly variable plant functional traits and thus to diverging plant responses to environmental changes. However, detailed measurements of plant hydraulic strategies and their inter- and intra-specific variability are still lacking for these ecosystems. Here, we quantify plant water use and hydraulic strategies of black spruce (Picea mariana) and larch (Larix laricina), that are widespread in the boreal zone, at a long-term monitoring site located in central Saskatchewan (53.99° N, 105.12° W; elevation 628.94 m a.s.l.). The site is characterized by a mature black spruce overstorey that dominates the landscape with few larch individuals. The ground cover consists mainly of mosses with some peat moss and lichens over a rich soil organic layer. Tree-level sap flux density, measured with Granier-style thermal dissipation probes (N=39), and concurrently recorded radial stem dynamics, measured with high frequency dendrometers (N=13), are used to quantify plant hydraulic functioning during the 2016 growing season. Hydrometeorological measurements, including soil moisture and micrometeorological data, are used to describe environmental constraints in plant water use. Tree-level dynamics are then integrated to the landscape and compared with ecosystem-level evapotranspiration measurements from an adjacent eddy-covariance flux tower. This experimental design allows us to quantify the main environmental drivers that shape plant hydraulic strategies in this southern boreal zone and to provide new insights into the inter- and

Thermal treatment and competing technologies for remediation of MGP (manufactured gas plant) sites

International Nuclear Information System (INIS)

McGowan, T.F.; Greer, B.A.; Lawless, M.

1995-01-01

More than 1,500 MGP (manufactured gas plant) sites exist throughout the US. Many are contaminated with coal tar from coal-fueled gas works which produced ''town gas'' from the mid-1800s through the 1950s. Virtually all old US cities have such sites. Most are in downtown areas, as they were installed for central distribution of manufactured gas. While a few sites are CERCLA/Superfund, most are not. However, the contaminants and methods used for remediation are similar to those used for Superfund cleanups of coal tar contamination from wood-treating and coke oven facilities. Clean-up of sites is triggered by property transfers and re-development as well as releases to the environment--in particular, via ground water migration. This paper describes recent experience with high capacity/low cost thermal desorption process for this waste. It also reviews competing non-thermal technology, such as bio-treatment, capping, recycling, and dig and haul. Cost data are provided for all technologies, and a case study for thermal treatment is also presented

Site preparation works for No.3 plant in Ikata Nuclear Power Station, Shikoku Electric Power Co., Inc

International Nuclear Information System (INIS)

Ishihara, Hisashi; Nakajima, Hiroshi; Oshima, Teruhiko

1986-01-01

Ikata Power Station is only nuclear power station in Shikoku located at the root of Sadamisaki Peninsula. No.1 plant started the operation in September, 1977, and No.2 plant started the operation in March, 1982. By constructing No.3 plant of 890 MWe output, the total power output will be 2.022 million kW. No.3 plant is installed adjacently to No.1 and No.2 plants on their east side. In this place, the existing facilities of the harbor and others can be effectively utilized, the nature of ground is solid, and the fundamental condition of location is perfect, it is easy to obtain the cooperation of local people as No.1 and No.2 plants have been in operation, and it is advantageous in view of the construction period for the power supply plan. The site preparation works have progressed smoothly since the start in June, 1985. About 100,000 m 2 of the site is created by cutting natural ground, and about 54,000 m 2 is created by sea reclamation. About 5 million m 3 of earth and stone generated by cutting and excavation are utilized for reclamation, revetment and others. The topographic and geological features, sea condition, the outline of geological survey, the layout, and the construction works of revetment, cutting, the creation of substitute seaweed farm, appurtenant works, and the measures for environment preservation are described. (Kako, I.)

Sludge stabilization at the Plutonium Finishing Plant, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1994-10-01

This Environmental Assessment evaluates the proposed action to operate two laboratory-size muffle furnaces in glovebox HC-21C, located in the Plutonium Finishing Plant (PFP), Hanford Site, Richland, Washington. The muffle furnaces would be used to stabilize chemically reactive sludges that contain approximately 25 kilograms (55 pounds) of plutonium by heating to approximately 500 to 1000 degrees C (900 to 1800 degrees F). The resulting stable powder, mostly plutonium oxide with impurities, would be stored in the PFP vaults. The presence of chemically reactive plutonium-bearing sludges in the process gloveboxes poses a risk to workers from radiation exposure and limits the availability of storage space for future plant cleanup. Therefore, there is a need to stabilize the material into a form suitable for long-term storage. This proposed action would be an interim action, which would take place prior to completion of an Environmental Impact Statement for the PFP which would evaluate stabilization of all plutonium-bearing materials and cleanout of the facility. However, only 10 percent of the total quantity of plutonium in reactive materials is in the sludges, so this action will not limit the choice of reasonable alternatives or prejudice the Record of Decision of the Plutonium Finishing Plant Environmental Impact Statement

Flora of IGCAR campus and PFBR site: II plant diversity analysis

International Nuclear Information System (INIS)

Gajendiran, N.; Ragupathy, S.

2003-09-01

This report highlights the level of plant diversity that prevails in IGCAR and PFBR sites. The stress tolerant sandy-shore flora of natural vegetation adorns the Campus. It is bewitchingly blended with horticultural design and sets the backdrop of the nuclear industries- MAPS I and II and the incumbent PFBR. The floristic analysis points out the genetic richness of the campus (over 650 plant species in a narrow strip of ∼2500 acres), which can also serve as genetic reserve for coastal flora. Based on the study, a digitized inventory of plant resources of Kalpakkam is now made available. Taxonomy, distribution, vernacular name, uses, produces, bio-chemical component, ethnobotany, photograph are featured in the database. The survey highlights the potential of mangroves as bio-fence protecting against cyclone and sand and salt laden wind erosion. Such information may also be useful to understand the flora of east coast, in general. Biodiversity information gains importance for its use in caring the ecosystem and for its wise management at every micro-level down to the back yard of individual institution, which is the need of the hour. The sustainable use and preserving the biological resources maximize the net long-term benefits to mankind. (author)

Staying Tight: Plasmodesmal Membrane Contact Sites and the Control of Cell-to-Cell Connectivity in Plants.

Science.gov (United States)

Tilsner, Jens; Nicolas, William; Rosado, Abel; Bayer, Emmanuelle M

2016-04-29

Multicellularity differs in plants and animals in that the cytoplasm, plasma membrane, and endomembrane of plants are connected between cells through plasmodesmal pores. Plasmodesmata (PDs) are essential for plant life and serve as conduits for the transport of proteins, small RNAs, hormones, and metabolites during developmental and defense signaling. They are also the only pathways available for viruses to spread within plant hosts. The membrane organization of PDs is unique, characterized by the close apposition of the endoplasmic reticulum and the plasma membrane and spoke-like filamentous structures linking the two membranes, which define PDs as membrane contact sites (MCSs). This specialized membrane arrangement is likely critical for PD function. Here, we review how PDs govern developmental and defensive signaling in plants, compare them with other types of MCSs, and discuss in detail the potential functional significance of the MCS nature of PDs.

Threatened plant species of the Nevada Test Site, Ash Meadows, central-southern Nevada

Energy Technology Data Exchange (ETDEWEB)

Beatley, J.C.

1977-04-01

This report is a companion one to Endangered Plant Species of the Nevada Test Site, Ash Meadows, and Central-Southern Nevada (COO-2307-11) and deals with the threatened plant species of the same area. The species are those cited in the Federal Register, July 1, 1975, and include certain ones listed as occurring only in California or Arizona, but which occur also in central-southern Nevada. As with the earlier report, the purpose of this one is to record in detail the location of the past plant collections which constitute the sole or principal basis for defining the species' distributions and frequency of occurrence in southern Nye County, Nevada, and to recommend the area of the critical habitat where this is appropriate. Many of the species occur also in southern California, and for these the central-southern Nevada records are presented for consideration of the overall status of the species throughout its range.

Source removal strategy development for manufactured gas plant sites

International Nuclear Information System (INIS)

Golchin, J.; Nelson, S.

1994-01-01

A source removal action plan was developed by Midwest Gas and the Iowa Department of Natural Resources to address the source coal tar contamination within the underground gas holder basin at former Manufactured Gas Plant (MGP) sites. The procedure utilizes a mixture of coal, contaminated soil and coal rat sludge to provide a material that had suitable material handling characteristics for shipment and burning in high efficiency utility boilers. Screening of the mixture was required to remove oversized debris and ferrous metal. The resulting mixture did not exhibit toxic characteristics when tested under the Toxicity Characteristics Leaching Procedure (TCLP). Test results on the coal tar sludges have indicated that the more pure coal tar materials may fail the TCLP test and be classified as a RCRA hazardous waste. The processing procedure was designed to stabilize the coal tar sludges and render those sludges less hazardous and, as a result, able to pass the TCLP test. This procedure was adopted by the Edison Electric Institute to develop a national guidance document for remediation of MGP sites. The EPA Office of Solid Waste and Emergency Response recommended this strategy to the Regional Waste Management Directors as a practical tool for handling wastes that may exhibit the RCRA characteristics

Model calculating annual mean atmospheric dispersion factor for coastal site of nuclear power plant

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

This paper describes an atmospheric dispersion field experiment performed on the coastal site of nuclear power plant in the east part of China during 1995 to 1996. The three-dimension joint frequency are obtained by hourly observation of wind and temperature on a 100m high tower; the frequency of the “event day of land and sea breezes” are given by observation of surface wind and land and sea breezes; the diffusion parameters are got from measurements of turbulent and wind tunnel simulation test.A new model calculating the annual mean atmospheric dispersion factor for coastal site of nuclear power plant is developed and established.This model considers not only the effect from mixing release and mixed layer but also the effect from the internal boundary layer and variation of diffusion parameters due to the distance from coast.The comparison between results obtained by the new model and current model shows that the ratio of annual mean atmospheric dispersion factor gained by the new model and the current one is about 2.0.

2015 Annual Wastewater Reuse Report for the Idaho National Laboratory Site's Central Facilities Area Sewage Treatment Plant

International Nuclear Information System (INIS)

Lewis, Michael George

2016-01-01

This report describes conditions, as required by the state of Idaho Wastewater Reuse Permit (#LA-000141-03), for the wastewater land application site at the Idaho National Laboratory Site's Central Facilities Area Sewage Treatment Plant from November 1, 2014, through October 31, 2015.

The Expedited Remedial Action Program: A case study. The Alhambra Front Street manufactured gas plant site

Energy Technology Data Exchange (ETDEWEB)

Padleschat, J.A.; McMahon, T.D.

1996-12-31

Early in 1995, the Department of Toxic Substances Control asked Southern California Gas Company (SoCalGas) to enter one of its manufactured gas plant (MGP) sites into the new Expedited Remedial Action Program (ERAP). SoCalGas initially was not enthusiastic about the new program. Nevertheless, SoCalGas submitted an application for its Alhambra MGP site to be selected for the ERAP. The Alhambra Site was accepted into ERAP in November 1995, and was the first ERAP site to have orphan shares. MGP sites are well suited to the ERAP. They often involve few potentially responsible parties and can be expected to have the same primary contaminants: polycyclic aromatic hydrocarbons (PAH), which are a byproduct of the gas manufacturing process, and petroleum hydrocarbons from the crude oil feedstock used to manufacture the gas.

Environmentally acceptable endpoints for PAHs at a manufactured gas plant site

Energy Technology Data Exchange (ETDEWEB)

Stroo, H.F.; Jensen, R.; Loehr, R.C.; Nakles, D.V.; Fairbrother, A.; Liban, C.B. [ThermoRetec Corp., Carson, CA (USA)

2000-09-01

Samples from a former manufactured gas plant (MGP) site in Santa Barbara, CA were tested to evaluate the environmentally acceptable endpoints (EAE) process for setting risk-based cleanup criteria. The research was part of an ongoing effort to develop and demonstrate a protocol for assessing risk-based criteria for MGP sites that incorporates the availability of polycyclic aromatic hydrocarbons (PAHs). Six soil samples were subjected to a battery of physical and biological tests that focused on determining the 'availability' of the soil-bound contaminants to groundwater, ecological receptors, and human receptors. Results demonstrated that sorption to soil, matrix effects, aging, and treatment can significantly reduce chemical availability. Including these reduced availability results in risk assessment calculations yielded environmentally protective cleanup levels almost 3-10 times greater than levels derived using California default risk assessment assumptions. Using an EAE-based approach for MGP soils, especially those containing lampblack, could provide more realistic risk assessment. 23 refs., 6 tabs.

A method for locating potential tree-planting sites in urban areas: a case study of Los Angeles, USA

Science.gov (United States)

Chunxia Wua; Qingfu Xiaoa; Gregory E. McPherson

2008-01-01

A GIS-based method for locating potential tree-planting sites based on land cover data is introduced. Criteria were developed to identify locations that are spatially available for potential tree planting based on land cover, sufficient distance from impervious surfaces, a minimum amount of pervious surface, and no crown overlap with other trees. In an ArcGIS...

Influence of the crustal and subcrustal Vrancea seismic sources on Cernavoda nuclear power plant site

International Nuclear Information System (INIS)

Marmureanu, Gheorghe; Popescu, Emilia; Mircea Radulian

2002-01-01

The basis of the seismic hazard assessment in different geographical regions with dense-populated areas and strategic objectives (dams, nuclear power plants, etc.) is the study of seismicity of the seismogenic sources which affect these sites. The purpose of this paper is to provide a complete set of information relative to the Vrancea seismic source (in the crust and the intermediate depth domains) that is fundamental for the seismic hazard evaluation at Cernavoda nuclear power plant site. The analysis that we propose has to deal with the following items: (1) geometrical definition of the seismic sources; (2) setting the earthquake catalog associated to each seismic source; (3) estimation of the maximum possible magnitude; (4) estimation of the frequency - magnitude relationship; (5) computation of the distribution function for focal distance; (6) correlation between focal depth and magnitude; (7) attenuation law. We discuss also the implications of the model parameters on the seismic hazard level. (authors)

An Extreme Meteorological Events Analysis For Nuclear Power Plant (NPP) Siting Project at Bangka Island, Indonesia

Science.gov (United States)

Septiadi, Deni; S, Yarianto Sugeng B.; Sriyana; Anzhar, Kurnia; Suntoko, Hadi

2018-03-01

The potential sources of meteorological phenomena in Nuclear Power Plant (NPP) area of interest are identified and the extreme values of the possible resulting hazards associated which such phenomena are evaluated to derive the appropriate design bases for the NPP. The appropriate design bases shall be determined according to the Nuclear Energy Regulatory Agency (Bapeten) applicable regulations, which presently do not indicate quantitative criteria for purposes of determining the design bases for meteorological hazards. These meteorological investigations are also carried out to evaluate the regional and site specific meteorological parameters which affect the transport and dispersion of radioactive effluents on the environment of the region around the NPP site. The meteorological hazards are to be monitored and assessed periodically over the lifetime of the plant to ensure that consistency with the design assumptions is maintained throughout the full lifetime of the facility.

SITE-2, Power Plant Siting, Cost, Environment, Seismic and Meteorological Effects

International Nuclear Information System (INIS)

Frigerio, N.A.; Habegger, L.J.; King, R.F.; Hoover, L.J.; Clark, N.A.; Cobian, J.M.

1977-01-01

1 - Description of problem or function: SITE2 is designed to (1) screen candidate energy facility sites or areas within an electric utility region, based on the region's physical and socioeconomic attributes, the planned facility's characteristics, and impact assessments, and (2) evaluate the cumulative regional impacts associated with alternate energy supply options and inter-regional energy import/export practices, specifically, comparison of different energy technologies and their regional distribution in clustered or dispersed patterns. 2 - Method of solution: The SITE2 methodology is based on the quantification of three major site-related vectors. A cost vector is determined which identifies site-specific costs, such as transmission costs, cooling costs as related to water availability, and costs of specific controls needed to protect the surrounding environment. An impact vector is also computed for each potential site, using models of health and environmental impacts incurred in areas adjacent to the site. Finally, a site attribute vector is developed which reflects such characteristics as population, seismic conditions, meteorology, land use, and local ecological systems. This vector can be used to eliminate certain sites because of their inability to satisfy specific constraints. These three vectors can be displayed as density maps and combined in a simple overlay approach, similar to that developed by I. L. McHarg in reference 2, to identify candidate sites. Alternatively, the vector elements can be computationally combined into a weighted sum to obtain quantitative indicators of site suitability

SITE-2, Power Plant Siting, Cost, Environment, Seismic and Meteorological Effects

Energy Technology Data Exchange (ETDEWEB)

Frigerio, N A [Environmental Impact Studies, Argonne National Laboratory 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Habegger, L J; King, R F; Hoover, L J [Energy and Environmental Systems Division, Argonne National Laboratory 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Clark, N A [Applied Mathematics Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Cobian, J M [Northwestern University, Evanston, Illinois 60201 (United States)

1977-08-01

1 - Description of problem or function: SITE2 is designed to (1) screen candidate energy facility sites or areas within an electric utility region, based on the region's physical and socioeconomic attributes, the planned facility's characteristics, and impact assessments, and (2) evaluate the cumulative regional impacts associated with alternate energy supply options and inter-regional energy import/export practices, specifically, comparison of different energy technologies and their regional distribution in clustered or dispersed patterns. 2 - Method of solution: The SITE2 methodology is based on the quantification of three major site-related vectors. A cost vector is determined which identifies site-specific costs, such as transmission costs, cooling costs as related to water availability, and costs of specific controls needed to protect the surrounding environment. An impact vector is also computed for each potential site, using models of health and environmental impacts incurred in areas adjacent to the site. Finally, a site attribute vector is developed which reflects such characteristics as population, seismic conditions, meteorology, land use, and local ecological systems. This vector can be used to eliminate certain sites because of their inability to satisfy specific constraints. These three vectors can be displayed as density maps and combined in a simple overlay approach, similar to that developed by I. L. McHarg in reference 2, to identify candidate sites. Alternatively, the vector elements can be computationally combined into a weighted sum to obtain quantitative indicators of site suitability.

Environmental impact statement on the siting of nuclear power plants: scoping summary report

International Nuclear Information System (INIS)

1981-12-01

The NRC staff has completed its scoping process for the Environmental Impact Statement for the revision of its regulations on the siting of nuclear power plants. The rulemaking and environmental review have been focused to concentrate on significant issues and alternatives and to delete items from the rulemaking on which it is not appropriate to proceed at this time. A brief discussion of the major comments is included

300 Area steam plant replacement, Hanford Site, Richland, Washington: Environmental assessment

International Nuclear Information System (INIS)

1997-03-01

Steam to support process operations and facility heating is currently produced by a centralized oil-fired plant located in the 300 Area and piped to approximately 26 facilities in the 300 Area. This plant was constructed during the 1940s and, because of tis age, is not efficient, requires a relatively large operating and maintenance staff, and is not reliable. The US Department of Energy is proposing an energy conservation measure for a number of buildings in the 300 Area of the Hanford Site. This action includes replacing the centralized heating system with heating units for individual buildings or groups of buildings, constructing new natural gas pipelines to provide a fuel source for many of these units and constructing a central control building to operate and maintain the system. A new steel-sided building would be constructed in the 300 Area in a previously disturbed area at least 400 m (one-quarter mile) from the Columbia River, or an existing 300 Area building would be modified and used. This Environmental Assessment evaluates alternatives to the proposed actions. Alternatives considered are: (1) the no action alternative; (2) use of alternative fuels, such as low-sulfur diesel oil; (3) construction of a new central steam plant, piping and ancillary systems; (4) upgrade of the existing central steam plant and ancillary systems; and (5) alternative routing of the gas distribution pipeline that is a part of the proposed action. A biological survey and culture resource review and survey were also conducted

Thermal treatment and non-thermal technologies for remediation of manufactured gas plant sites

International Nuclear Information System (INIS)

McGowan, T.F.; Greer, B.A.; Lawless, M.

1996-01-01

More than 1,500 manufactured gas plant (MGP) sites exist throughout the US. Many are contaminated with coal tar from coal-fueled gas works which produced town gas from the mid-1800s through the 1950s. Virtually all old US cities have such sites. Most are in downtown areas as they were installed for central distribution of manufactured gas. While a few sites are CERCLA/Superfund, most are not. However, the contaminants and methods used for remediation are similar to those used for Superfund clean-ups of coal tar contamination from wood-treating and coke oven facilities. Clean-up of sites is triggered by regulatory pressure, property transfers and re-development as well as releases to the environment--in particular, via groundwater migration. Due to utility de-regulation, site clean-ups may also be triggered by sale of a utility or of a specific utility site to other utilities. Utilities have used two approaches in dealing with their MGP sites. The first is do nothing and hope for the best. History suggests that, sooner or later, these sites become a bigger problem via a release, citizen lawsuit or regulatory/public service commission intervention. The second, far better approach is to define the problem now and make plans /for waste treatment or immobilization. This paper describes recent experience with a high capacity/low cost thermal desorption process for this waste and reviews non-thermal technology, such as bio-treatment, capping, recycling, and dig and haul. Cost data are provided for all technologies, and a case study for thermal treatment is also presented

Site selection for nuclear power plants

International Nuclear Information System (INIS)

Ehjchkholz, D.

1980-01-01

Problem of NPP site selection in the USA including engineering factors, radiation and environmental protection factors is stated in detail. Floating and underground sites are considered especially. The attention in paid to waste storage and risk criterium in siting [ru

Insights from Siting New Nuclear Power Plants in the Central and Eastern United States

International Nuclear Information System (INIS)

Munson, Clifford G.; Kugler, Andrew J.

2011-01-01

The staff of the U.S. Nuclear Regulatory Commission (NRC) has completed its review for four early site permits and for four standard reactor designs. It is currently reviewing applications for fourteen combined license applications and three additional reactor designs. The staff is applying lessons it has learned from the reviews to date to the review work going forward. The licensing process being used by current applicants differs significantly from that used by the current operating fleet. The previous process required two steps. First an applicant had to obtain a construction permit to build the plant. Then, near the end of construction, the applicant had to obtain an operating license. Under the process in Part 52, an applicant can apply for a combined license (COL) that allows construction and (once certain conditions are met) operation of a new plant - a one-step process. An applicant for a COL may reference an early site permit (ESP13), a standard design certification, both, or neither. In addition to developing Part 52, the NRC also revised CFR Part 100 by adding Subpart B, which includes sections 100.21, 'Non-seismic siting criteria', and 100.23, 'Geologic and seismic siting criteria'. The NRC staff also revised the Standard Review Plan (NUREG-0800) and developed Regulatory Guide (RG) 1.206, 'Combined License Applications for Nuclear Power Plants (LWR Edition).' The NRC staff incorporated into the revision of NUREG-0800 and development of RG 1.206 some early lessons learned from its review of the first three ESPs. Staff work begins before the application is received, as the staff interacts with the applicant to identify issues that will require special treatment or specific staff resources. After the application is submitted, if the NRC finds the application acceptable, the safety and environmental reviews begin, proceeding in parallel. The safety review culminates in the issuance of a safety evaluation report (SER) after it

Waste Isolation Pilot Plant site environmental report, for calendar year 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The U.S. Department of Energy (DOE) Order 5400.1 General Environmental Protection Program, requires DOE facilities, that conduct environmental protection programs, to annually prepare a Site Environmental Report (SER). The purpose of the SER is to provide an abstract of environmental assessments conducted in order to characterize site environmental management performance, to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit. The content of this SER is not restricted to a synopsis of the required data, in addition, information pertaining to new and continued monitoring and compliance activities during the 1995 calendar year are also included. Data contained in this report are derived from those monitoring programs directed by the Waste Isolation Pilot Plant (WIPP) Environmental Monitoring Plan (EMP). The EMP provides inclusive guidelines implemented to detect potential impacts to the environment and to establish baseline measurements for future environmental evaluations. Surface water, groundwater. air, soil, and biotic matrices are monitored for an array of radiological and nonradiological factors. The baseline radiological surveillance program encompasses a broader geographic area that includes nearby ranches, villages, and cities. Most elements of nonradiological assessments are conducted within the geographic vicinity of the WIPP site.

Waste Isolation Pilot Plant site environmental report, for calendar year 1995

International Nuclear Information System (INIS)

1996-01-01

The U.S. Department of Energy (DOE) Order 5400.1 General Environmental Protection Program, requires DOE facilities, that conduct environmental protection programs, to annually prepare a Site Environmental Report (SER). The purpose of the SER is to provide an abstract of environmental assessments conducted in order to characterize site environmental management performance, to confirm compliance with environmental standards and requirements, and to highlight significant programs and efforts of environmental merit. The content of this SER is not restricted to a synopsis of the required data, in addition, information pertaining to new and continued monitoring and compliance activities during the 1995 calendar year are also included. Data contained in this report are derived from those monitoring programs directed by the Waste Isolation Pilot Plant (WIPP) Environmental Monitoring Plan (EMP). The EMP provides inclusive guidelines implemented to detect potential impacts to the environment and to establish baseline measurements for future environmental evaluations. Surface water, groundwater. air, soil, and biotic matrices are monitored for an array of radiological and nonradiological factors. The baseline radiological surveillance program encompasses a broader geographic area that includes nearby ranches, villages, and cities. Most elements of nonradiological assessments are conducted within the geographic vicinity of the WIPP site

Neutron generator production mission in a national laboratory.

Energy Technology Data Exchange (ETDEWEB)

Pope, Larry E.

2007-08-01

In the late 1980's the Department of Energy (DOE) faced a future budget shortfall. By the spring of 1991, the DOE had decided to manage this problem by closing three production plants and moving production capabilities to other existing DOE sites. As part of these closings, the mission assignment for fabrication of War Reserve (WR) neutron generators (NGs) was transferred from the Pinellas Plant (PP) in Florida to Sandia National Laboratories, New Mexico (SNL/NM). The DOE directive called for the last WR NG to be fabricated at the PP before the end of September 1994 and the first WR NG to be in bonded stores at SNL/NM by October 1999. Sandia National Laboratories successfully managed three significant changes to project scope and schedule and completed their portion of the Reconfiguration Project on time and within budget. The PP was closed in October 1995. War Reserve NGs produced at SNL/NM were in bonded stores by October 1999. The costs of the move were recovered in just less than five years of NG production at SNL/NM, and the annual savings today (in 1995 dollars) is $47 million.

Potential impacts of sea level rise on native plant communities and associated cultural sites in coastal areas of the main Hawaiian Islands

Science.gov (United States)

Jacobi, James D.; Warshauer, Frederick R.

2017-01-01

Hawaiian coastal vegetation is comprised of plant species that are adapted to growing in extremely harsh conditions (salt spray, wave wash, wind, and substrates with limited nutrients) found in this habitat zone. Prior to human colonization of Hawai‘i coastal vegetation extended as a continuous ring around each of the islands, broken only by stretches of recent lava flows or unstable cliff faces. However, since humans arrived in Hawai‘i many areas that originally supported native coastal plant communities have been highly altered or the native vegetation totally removed for agriculture, housing, or resort development, destroyed by fire, displaced by invasive plants, eaten by introduced mammals, or damaged by recreational use. This study was focused on identifying sites that still retain relatively intact and highly diverse native coastal plant communities throughout the main Hawaiian Islands that may be further impacted by projected sea level rise. Approximately 40 percent of Hawai‘i’s coastlines were found to still contain high quality native coastal plant communities. Most of these sites were located in areas where the coastal vegetation can still migrate inshore in response to rising sea level and associated inundation by waves. However, six sites with high-quality native coastal vegetation were found on low-lying offshore islets that will be totally inundated with a one meter increase in sea level and thirty sites were found to have some type of fixed barrier, such as a paved road or structure, which would restrict the plants from colonizing the adjacent inland areas. Many of these sites also have other cultural resources that are fixed in place and will definitely be impacted by rising sea level. The results of this study can help refine our understanding of Hawai‘i’s remaining native coastal vegetation and aid with the development of management and restoration strategies to ensure the long-term survival of these unique plant communities.

Environmental impact assessment of decommissioning treatment about radioactive model plant waste ore storage site

International Nuclear Information System (INIS)

Bei Xinyu

2012-01-01

Aiming at decommissioning treatment project of radioactive model plant waste ore storage site, based on the detailed investigations of source terms and project description, systematic environmental impacts have been identified. The environmental impacts both during decommissioning treatment, radioactive waste transportation and after treatment are assessed. Some specific environmental protection measures are proposed so as to minimize the adverse environmental impacts. (author)

Apoplastic interactions between plants and plant root intruders

Directory of Open Access Journals (Sweden)

Kanako eMitsumasu

2015-08-01

Full Text Available Numerous pathogenic or parasitic organisms attack plant roots to obtain nutrients, and the apoplast including the plant cell wall is where the plant cell meets such organisms. Root-parasitic angiosperms and nematodes are two distinct types of plant root parasites but share some common features in their strategies for breaking into plant roots. Striga and Orobanche are obligate root parasitic angiosperms that cause devastating agricultural problems worldwide. Parasitic plants form an invasion organ called a haustorium, where plant cell wall degrading enzymes (PCWDEs are highly expressed. Plant-parasitic nematodes are another type of agriculturally important plant root parasite. These nematodes breach the plant cell walls by protruding a sclerotized stylet from which PCWDEs are secreted. Responding to such parasitic invasion, host plants activate their own defense responses against parasites. Endoparasitic nematodes secrete apoplastic effectors to modulate host immune responses and to facilitate the formation of a feeding site. Apoplastic communication between hosts and parasitic plants also contributes to their interaction. Parasitic plant germination stimulants, strigolactones (SLs, are recently identified apoplastic signals that are transmitted over long distances from biosynthetic sites to functioning sites. Here, we discuss recent advances in understanding the importance of apoplastic signals and cell walls for plant-parasite interactions.

Apoplastic interactions between plants and plant root intruders.

Science.gov (United States)

Mitsumasu, Kanako; Seto, Yoshiya; Yoshida, Satoko

2015-01-01

Numerous pathogenic or parasitic organisms attack plant roots to obtain nutrients, and the apoplast including the plant cell wall is where the plant cell meets such organisms. Root parasitic angiosperms and nematodes are two distinct types of plant root parasites but share some common features in their strategies for breaking into plant roots. Striga and Orobanche are obligate root parasitic angiosperms that cause devastating agricultural problems worldwide. Parasitic plants form an invasion organ called a haustorium, where plant cell wall degrading enzymes (PCWDEs) are highly expressed. Plant-parasitic nematodes are another type of agriculturally important plant root parasite. These nematodes breach the plant cell walls by protruding a sclerotized stylet from which PCWDEs are secreted. Responding to such parasitic invasion, host plants activate their own defense responses against parasites. Endoparasitic nematodes secrete apoplastic effectors to modulate host immune responses and to facilitate the formation of a feeding site. Apoplastic communication between hosts and parasitic plants also contributes to their interaction. Parasitic plant germination stimulants, strigolactones, are recently identified apoplastic signals that are transmitted over long distances from biosynthetic sites to functioning sites. Here, we discuss recent advances in understanding the importance of apoplastic signals and cell walls for plant-parasite interactions.