WorldWideScience

Sample records for phase iii glovebox

  1. Glovebox and Experiment Safety

    Science.gov (United States)

    Maas, Gerard

    2005-12-01

    Human spaceflight hardware and operations must comply with NSTS 1700.7. This paper discusses how a glovebox can help.A short layout is given on the process according NSTS/ISS 13830, explaining the responsibility of the payload organization, the approval authority of the PSRP and the defined review phases (0 till III).Amongst others, the following requirement has to be met:"200.1 Design to Tolerate Failures. Failure tolerance is the basic safety requirement that shall be used to control most payload hazards. The payload must tolerate a minimum number of credible failures and/or operator errors determined by the hazard level. This criterion applies when the loss of a function or the inadvertent occurrence of a function results in a hazardous event.200.1a Critical Hazards. Critical hazards shall be controlled such that no single failure or operator error can result in damage to STS/ISS equipment, a nondisabling personnel injury, or the use of unscheduled safing procedures that affect operations of the Orbiter/ISS or another payload.200.1b Catastrophic Hazards. Catastrophic hazards shall be controlled such that no combination of two failures or operator errors can result in the potential for a disabling or fatal personnel injury or loss of the Orbiter/ISS, ground facilities or STS/ISS equipment."For experiments in material science, biological science and life science that require real time operator manipulation, the above requirement may be hard or impossible to meet. Especially if the experiment contains substances that are considered hazardous when released into the habitable environment. In this case operation of the experiment in a glovebox can help to comply.A glovebox provides containment of the experiment and at the same time allows manipulation and visibility to the experiment.The containment inside the glovebox provides failure tolerance because the glovebox uses a negative pressure inside the working volume (WV). The level of failure tolerance is dependent of

  2. TRU waste characterization chamber gloveboxes

    International Nuclear Information System (INIS)

    Duncan, D. S.

    1998-01-01

    Argonne National Laboratory-West (ANL-W) is participating in the Department of Energy's (DOE) National Transuranic Waste Program in support of the Waste Isolation Pilot Plant (WIPP). The Laboratory's support currently consists of intrusive characterization of a selected population of drums containing transuranic waste. This characterization is performed in a complex of alpha containment gloveboxes termed the Waste Characterization Gloveboxes. Made up of the Waste Characterization Chamber, Sample Preparation Glovebox, and the Equipment Repair Glovebox, they were designed as a small production characterization facility for support of the Idaho National Engineering and Environmental Laboratory (INEEL). This paper presents salient features of these gloveboxes

  3. Glovebox decontamination technology comparison

    International Nuclear Information System (INIS)

    Quintana, D.M.; Rodriguez, J.B.; Cournoyer, M.E.

    1999-01-01

    Reconfiguration of the CMR Building and TA-55 Plutonium Facility for mission requirements will require the disposal or recycle of 200--300 gloveboxes or open front hoods. These gloveboxes and open front hoods must be decontaminated to meet discharge limits for Low Level Waste. Gloveboxes and open front hoods at CMR have been painted. One of the deliverables on this project is to identify the best method for stripping the paint from large numbers of gloveboxes. Four methods being considered are the following: conventional paint stripping, dry ice pellets, strippable coatings, and high pressure water technology. The advantages of each technology will be discussed. Last, cost comparisons between the technologies will be presented

  4. Students build glovebox at Space Science Center

    Science.gov (United States)

    2001-01-01

    Students in the Young Astronaut Program at the Coca-Cola Space Science Center in Columbus, GA, constructed gloveboxes using the new NASA Student Glovebox Education Guide. The young astronauts used cardboard copier paper boxes as the heart of the glovebox. The paper boxes transformed into gloveboxes when the students pasted poster-pictures of an actual NASA microgravity science glovebox inside and outside of the paper boxes. The young astronauts then added holes for gloves and removable transparent top covers, which completed the construction of the gloveboxes. This image is from a digital still camera; higher resolution is not available.

  5. Redefining design criteria for Pu-238 gloveboxes

    International Nuclear Information System (INIS)

    Acosta, S.V.

    1998-01-01

    Enclosures for confinement of special nuclear materials (SNM) have evolved into the design of gloveboxes. During the early stages of glovebox technology, established practices and process operation requirements defined design criteria. Proven boxes that performed and met or exceeded process requirements in one group or area, often could not be duplicated in other areas or processes, and till achieve the same success. Changes in materials, fabrication and installation methods often only met immediate design criteria. Standardization of design criteria took a big step during creation of ''Special-Nuclear Materials R and D Laboratory Project, Glovebox standards''. The standards defined design criteria for every type of process equipment in its most general form. Los Alamos National Laboratory (LANL) then and now has had great success with Pu-238 processing. However with ever changing Environment Safety and Health (ES and H) requirements and Ta-55 Facility Configuration Management, current design criteria are forced to explore alternative methods of glovebox design fabrication and installation. Pu-238 fuel processing operations in the Power Source Technologies Group have pushed the limitations of current design criteria. More than half of Pu-238 gloveboxes are being retrofitted or replaced to perform the specific fuel process operations. Pu-238 glovebox design criteria are headed toward process designed single use glovebox and supporting line gloveboxes. Gloveboxes that will house equipment and processes will support TA-55 Pu-238 fuel processing needs into the next century and extend glovebox expected design life

  6. WRAP low level waste (LLW) glovebox operational test report

    Energy Technology Data Exchange (ETDEWEB)

    Kersten, J.K.

    1998-02-19

    The Low Level Waste (LLW) Process Gloveboxes are designed to: receive a 55 gallon drum in an 85 gallon overpack in the Entry glovebox (GBIOI); and open and sort the waste from the 55 gallon drum, place the waste back into drum and relid in the Sorting glovebox (GB 102). In addition, waste which requires further examination is transferred to the LLW RWM Glovebox via the Drath and Schraeder Bagiess Transfer Port (DO-07-201) or sent to the Sample Transfer Port (STC); crush the drum in the Supercompactor glovebox (GB 104); place the resulting puck (along with other pucks) into another 85 gallon overpack in the Exit glovebox (GB 105). The status of the waste items is tracked by the Data Management System (DMS) via the Plant Control System (PCS) barcode interface. As an item is moved from the entry glovebox to the exit glovebox, the Operator will track an items location using a barcode reader and enter any required data on the DMS console. The Operational Test Procedure (OTP) will perform evolution`s (described below) using the Plant Operating Procedures (POP) in order to verify that they are sufficient and accurate for controlled glovebox operation.

  7. WRAP low level waste (LLW) glovebox operational test report

    International Nuclear Information System (INIS)

    Kersten, J.K.

    1998-01-01

    The Low Level Waste (LLW) Process Gloveboxes are designed to: receive a 55 gallon drum in an 85 gallon overpack in the Entry glovebox (GBIOI); and open and sort the waste from the 55 gallon drum, place the waste back into drum and relid in the Sorting glovebox (GB 102). In addition, waste which requires further examination is transferred to the LLW RWM Glovebox via the Drath and Schraeder Bagiess Transfer Port (DO-07-201) or sent to the Sample Transfer Port (STC); crush the drum in the Supercompactor glovebox (GB 104); place the resulting puck (along with other pucks) into another 85 gallon overpack in the Exit glovebox (GB 105). The status of the waste items is tracked by the Data Management System (DMS) via the Plant Control System (PCS) barcode interface. As an item is moved from the entry glovebox to the exit glovebox, the Operator will track an items location using a barcode reader and enter any required data on the DMS console. The Operational Test Procedure (OTP) will perform evolution's (described below) using the Plant Operating Procedures (POP) in order to verify that they are sufficient and accurate for controlled glovebox operation

  8. Institutional glovebox safety committee (IGSC) annual report FY2010

    Energy Technology Data Exchange (ETDEWEB)

    Cournoyer, Michael E [Los Alamos National Laboratory; Roybal, Richard F [Los Alamos National Laboratory; Lee, Roy J [Los Alamos National Laboratory

    2011-01-04

    The Institutional Glovebox Safety Committee (IGSC) was chartered to minimize and/or prevent glovebox operational events. Highlights of the IGSC's third year are discussed. The focus of this working committee is to address glovebox operational and safety issues and to share Lessons Learned, best practices, training improvements, and glovebox glove breach and failure data. Highlights of the IGSC's third year are discussed. The results presented in this annual report are pivotal to the ultimate focus of the glovebox safety program, which is to minimize work-related injuries and illnesses. This effort contributes to the LANL Continuous Improvement Program by providing information that can be used to improve glovebox operational safety.

  9. Electrochemical decontamination system for actinide processing gloveboxes

    International Nuclear Information System (INIS)

    Wedman, D.E.; Lugo, J.L.; Ford, D.K.; Nelson, T.O.; Trujillo, V.L.; Martinez, H.E.

    1998-03-01

    An electrolytic decontamination technology has been developed and successfully demonstrated at Los Alamos National Laboratory (LANL) for the decontamination of actinide processing gloveboxes. The technique decontaminates the interior surfaces of stainless steel gloveboxes utilizing a process similar to electropolishing. The decontamination device is compact and transportable allowing it to be placed entirely within the glovebox line. In this way, decontamination does not require the operator to wear any additional personal protective equipment and there is no need for additional air handling or containment systems. Decontamination prior to glovebox decommissioning reduces the potential for worker exposure and environmental releases during the decommissioning, transport, and size reduction procedures which follow. The goal of this effort is to reduce contamination levels of alpha emitting nuclides for a resultant reduction in waste level category from High Level Transuranic (TRU) to low Specific Activity (LSA, less than or equal 100 nCi/g). This reduction in category results in a 95% reduction in disposal and disposition costs for the decontaminated gloveboxes. The resulting contamination levels following decontamination by this method are generally five orders of magnitude below the LSA specification. Additionally, the sodium sulfate based electrolyte utilized in the process is fully recyclable which results in the minimum of secondary waste. The process bas been implemented on seven gloveboxes within LANL's Plutonium Facility at Technical Area 55. Of these gloveboxes, two have been discarded as low level waste items and the remaining five have been reused

  10. Dexterity test data contribute to proper glovebox over-glove use

    International Nuclear Information System (INIS)

    Cournoyer, Michael E.; Lawton, Cindy M.; Castro, Armanda M.; Costigan, Stephen A.; Apel, D.M.; Neal, G.E.; Castro, J.M.; Michelotti, R.A.

    2010-01-01

    Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (TA-55) involve working with various amounts of plutonium and other highly toxic, alpha-emitting materials. The spread of radiological contamination on surfaces, airborne contamination, and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes (the glovebox, coupled with an adequate negative pressure gradient, provides primary confinement). The glovebox gloves are the weakest part of this engineering control. The Glovebox Glove Integrity Program, which controls glovebox gloves from procurement to disposal at TA-55, manages this vulnerability. A key element of this program is to consider measures that lower the overall risk of glovebox operations. Proper selection of over-gloves is one of these measures. Line management owning glovebox processes have the responsibility to approve the appropriate personal protective equipment/glovebox glove/over-glove combination. As low as reasonably achievable (ALARA) considerations to prevent unplanned glovebox glove openings must be balanced with glove durability and worker dexterity, both of which affect the final overall risk to the worker. In this study, the causes of unplanned glovebox glove openings, the benefits of over-glove features, the effect of over-gloves on task performance using standard dexterity tests, the pollution prevention benefits, and the recommended over-gloves for a task are presented.

  11. Compatibility of selected elastomers with plutonium glovebox environment

    International Nuclear Information System (INIS)

    Burns, R.

    1994-06-01

    This illustrative test was undertaken as a result of on-going failure of elastomer components in plutonium gloveboxes. These failures represent one of the major sources of required maintenance to keep gloveboxes operational. In particular, it was observed that the introduction of high specific activity Pu-238 into a glovebox, otherwise contaminated with Pu-239, resulted in an inordinate failure of elastomer components. Desiring to keep replacement of elastomer components to a minimum, a decision to explore a few possible alternative elastomer candidates was undertaken and reported upon herewith. Sample specimens of Neoprene, Urethane, Viton, and Hypalon elastomeric formulations were obtained from the Bacter Rubber Company. Strips of the elastomer specimens were placed in a plutonium glovebox and outside of a glovebox, and were observed for a period of three years. Of the four types of elastomers, only Hypalon remained completely viable

  12. Dismantling techniques for plutonium-contaminated gloveboxes: experience from first year of decommissioning

    International Nuclear Information System (INIS)

    Baumann, R.; Faber, P.

    2003-01-01

    At the mixed-oxide (MOX) processing facility formerly operated by ALKEM GmbH in Hanau, Germany - which was taken over to Siemens in 1988 and renamed Siemens' Hanau Fuel Fabrication Plant, MOX facility - around 8500 kg of plutonium were processed to make MOX fuel rods and fuel assemblies since production started in 1965. After shutdown of the facility by the authorities in mid-1991 for political reasons, the remaining nuclear fuel materials were processed during the subsequent ''cleanout'' phase starting in 1997 into rods and assemblies suitable for long-term storage. The last step in cleanout consisted of ''flushing'' the production equipment with depleted uranium and thoroughly cleaning the gloveboxes. During cleanout around 700 kg of plutonium were processed in the form of mixed oxides. The cleanout phase including the subsequent cleaning and flushing operations ended on schedule in September 2001 without any significant problems. Starting in mid-1999, the various glovebox dismantling techniques were tested using uncontaminated components while cleanout was still in progress and then, once these trials had been successfully completed, further qualified through use on actual components. The pilot-phase trials required four separate licenses under Section 7, Subsection (3) of the German Atomic Energy Act. Thanks to detailed advance planning and experience from the pilot trials the individual dismantling steps could be described in sufficient detail for the highly complex German licensing procedure. The first partial license for decommissioning the MOX facility under Sec. 7, Subsec. (3) of the Atomic Energy Act was issued on May 28, 2001. It mainly covers dismantling of the interior equipment inside the gloveboxes a well as the gloveboxes themselves. Actual decommissioning work inside the former production areas of the MOX facility started on a large scale in early September 2001. (orig.)

  13. MINIMIZING GLOVEBOX GLOVE BREACHES, PART IV: CONTROL CHARTS

    International Nuclear Information System (INIS)

    Cournoyer, Michael E.; Lee, Michelle B.; Schreiber, Stephen B.

    2007-01-01

    At the Los Alamos National Laboratory (LANL) Plutonium Facility, plutonium. isotopes and other actinides are handled in a glovebox environment. The spread of radiological contamination, and excursions of contaminants into the worker's breathing zone, are minimized and/or prevented through the use of glovebox technology. Evaluating the glovebox configuration, the glovebo gloves are the most vulnerable part of this engineering control. Recognizing this vulnerability, the Glovebox Glove Integrity Program (GGIP) was developed to minimize and/or prevent unplanned openings in the glovebox environment, i.e., glove failures and breaches. In addition, LANL implement the 'Lean Six Sigma (LSS)' program that incorporates the practices of Lean Manufacturing and Six Sigma technologies and tools to effectively improve administrative and engineering controls and work processes. One tool used in LSS is the use of control charts, which is an effective way to characterize data collected from unplanned openings in the glovebox environment. The benefit management receives from using this tool is two-fold. First, control charts signal the absence or presence of systematic variations that result in process instability, in relation to glovebox glove breaches and failures. Second, these graphical representations of process variation detennine whether an improved process is under control. Further, control charts are used to identify statistically significant variations (trends) that can be used in decision making to improve processes. This paper discusses performance indicators assessed by the use control charts, provides examples of control charts, and shows how managers use the results to make decisions. This effort contributes to LANL Continuous Improvement Program by improving the efficiency, cost effectiveness, and formality of glovebox operations.

  14. Guidelines for gloveboxes. Section 5.14: Electrical

    International Nuclear Information System (INIS)

    Tollner, R.L.

    1995-07-01

    This is the electric portion of the design guidelines for gloveboxes developed by the American Glovebox Society. The topics include applicable codes/industry standards, penetrations/feedthroughs, wireways, junction boxes, receptacles, derating factors, conductors, conductor insulation and grounding. References for the guidelines are provided

  15. An Integrated Science Glovebox for the Gateway Habitat

    Science.gov (United States)

    Calaway, M. J.; Evans, C. A.; Garrison, D. H.; Bell, M. S.

    2018-01-01

    Next generation habitats for deep space exploration of cislunar space, the Moon, and ultimately Mars will benefit from on-board glovebox capability. Such a glovebox facility will maintain sample integrity for a variety of scientific endeavors whether for life science, materials science, or astromaterials. Glovebox lessons learned from decades of astromaterials curation, ISS on-board sample handling, and robust analog missions provide key design and operational factors for inclusion in on-going habitat development.

  16. Robotic system for glovebox size reduction

    International Nuclear Information System (INIS)

    KWOK, KWAN S.; MCDONALD, MICHAEL J.

    2000-01-01

    The Intelligent Systems and Robotics Center (ISRC) at Sandia National Laboratories (SNL) is developing technologies for glovebox size reduction in the DOE nuclear complex. A study was performed for Kaiser-Hill (KH) at the Rocky Flats Environmental Technology Site (RFETS) on the available technologies for size reducing the glovebox lines that require size reduction in place. Currently, the baseline approach to these glovebox lines is manual operations using conventional mechanical cutting methods. The study has been completed and resulted in a concept of the robotic system for in-situ size reduction. The concept makes use of commercially available robots that are used in the automotive industry. The commercially available industrial robots provide high reliability and availability that are required for environmental remediation in the DOE complex. Additionally, the costs of commercial robots are about one-fourth that of the custom made robots for environmental remediation. The reason for the lower costs and the higher reliability is that there are thousands of commercial robots made annually, whereas there are only a few custom robots made for environmental remediation every year. This paper will describe the engineering analysis approach used in the design of the robotic system for glovebox size reduction

  17. Peak pressures from hydrogen deflagrations in the PFP thermal stabilization glovebox

    International Nuclear Information System (INIS)

    Van Keuren, J.C.

    1998-01-01

    This document describes the calculations of the peak pressures due to hydrogen deflagrations in the glovebox used for thermal stabilization (glovebox HC-21A) in PFP. Two calculations were performed. The first considered the burning of hydrogen released from a 7 inch Pu can in the Inert Atmosphere Confinement (IAC) section of the glovebox. The peak pressure increase was 12400 Pa (1.8 psi). The second calculation considered burning of the hydrogen from 25 g of plutonium hydride in the airlock leading to the main portion of the glovebox. Since the glovebox door exposes most of the airlock when open, the deflagration was assumed to pressurize the entire glovebox. The peak pressure increase was 3860 Pa (0.56 psi)

  18. Seismic analysis of plutonium glovebox by MSC/NASTRAN

    International Nuclear Information System (INIS)

    Hirata, Masaru; Ishikawa, Kazuya; Korosawa, Makoto; Fukushima, Susumu; Hoshina, Hirofumi.

    1993-01-01

    Seismic analysis of the structural strength of gloveboxes is important for plutonium confinement evaluation. However, the analytical methods must be developed for evaluating the mutual displacement between the window frame and acrylic resin window panel with regard to plutonium confinement during an earthquake. Therefore, seismic analysis for a standard glovebox in Plutonium Fuel Research Facility at Oarai Research Establishment of JAERI has been conducted by FEM (Finite Element Method) computer code MSC/NASTRAN (MacNeal-Schwendler Corporation NASA Structural Analysis). Modelling of glovebox window frame has been investigated from the results of natural frequency analysis and static analysis. After the acquisition of a suitable model, displacement around the window frame and glovebox structural strength have been evaluated in detail by use of floor response spectrum analysis and time-history (transient response) analysis. (author)

  19. HB-Line Dissolution of Glovebox Floor Sweepings

    International Nuclear Information System (INIS)

    Gray, J.H.

    1998-02-01

    Two candidate flowsheets for dissolving glovebox floor sweepings in the HB-Line Phase I geometrically favorable dissolver have been developed.Dissolving conditions tested and modified during the laboratory program were based on the current processing scheme for dissolving high-fired Pu-238 oxide in HB-Line. Subsequent adjustments made to the HB-Line flowsheet reflected differences in the dissolution behavior between high-fired Pu-238 oxide and the MgO sand/PuF 4 /PuO 2 mixture in glovebox floor sweepings. Although both candidate flowsheets involved two separate dissolving steps and resulted incomplete dissolution of all solids, the one selected for use in HB-Line will require fewer processing operations and resembles the initial flowsheet proposed for dissolving sand, slag, and crucible material in F-Canyon dissolvers. Complete dissolution of glovebox floor sweepings was accomplished in the laboratory by initially dissolving between 55 and 65 degree in a 14 molar nitric acid solution. Under these conditions, partial dissolution of PuF 4 and complete dissolution of PuO 2 and MgO sand were achieved in less than one hour. The presence of free fluoride in solution,uncomplexed by aluminum, was necessary for complete dissolution of the PuO 2 .The remaining PuF 4 dissolved following addition of aluminum nitrate nonahydrate (ANN) to complex the fluoride and heating between 75 and 85 degree C for an additional hour. Precipitation of magnesium and/or aluminum nitrates could occur before, during, and after transfer of product solutions. Both dilution and/or product solution temperature controls may be necessary to prevent precipitation of these salts. Corrosion of the dissolver should not be an issue during these dissolving operations. Corrosion is minimized when dissolving at 55-65 degree C for one to three hours at a maximum uncomplexed free fluoride concentration of 0.07 molar and by dissolving at 75-85 degree C at a one to one aluminum to fluoride mole ratio for another

  20. Determining the Radiation Damage Effect on Glovebox Glove Material

    International Nuclear Information System (INIS)

    Cournoyer, M.E.; Balkey, J.J.; Andrade, R.M.

    2005-01-01

    The Nuclear Material Technology (NMT) Division has the largest inventory of glove box gloves at Los Alamos National Laboratory. The minimization of unplanned breaches in the glovebox, e.g., glove failures, is a primary concern in the daily operations in NMT Division facilities, including the Plutonium Facility (PF-4) at TA-55 and Chemical and Metallurgy Research (CMR) Facility. Glovebox gloves in these facilities are exposed to elevated temperatures and exceptionally aggressive radiation environments (particulate 239 Pu and 238 Pu). Predictive models are needed to estimate glovebox glove service lifetimes, i.e. change-out intervals. Towards this aim aging studies have been initiated that correlate changes in mechanical (physical) properties with degradation chemistry. This present work derives glovebox glove change intervals based on previously reported mechanical data of thermally aged hypalon glove samples. Specifications for 30 mil tri-layered hypalon/lead glovebox gloves (TLH) and 15 mil hypalon gloves (HYP) have already been established. The relevant mechanical properties are shown on Table 1. Tensile strength is defined as the maximum load applied in breaking a tensile test piece divided by the original cross-sectional area of the test piece (Also termed maximum stress and ultimate tensile stress). Ultimate elongation is the elongation at time of rupture (Also termed maximum strain). The specification for the tensile test and ultimate elongation are the minimum acceptable values. In addition, the ultimate elongation must not vary 20% from the original value. In order to establish a service lifetimes for glovebox gloves in a thermal environment, the mechanical properties of glovebox glove materials were studied.

  1. Determining the Radiation Damage Effect on Glovebox Glove Material.

    Energy Technology Data Exchange (ETDEWEB)

    Cournoyer, M. E. (Michael E.); Balkey, J. J. (James J.); Andrade, R.M. (Rose M.)

    2005-01-01

    The Nuclear Material Technology (NMT) Division has the largest inventory of glove box gloves at Los Alamos National Laboratory. The minimization of unplanned breaches in the glovebox, e.g., glove failures, is a primary concern in the daily operations in NMT Division facilities, including the Plutonium Facility (PF-4) at TA-55 and Chemical and Metallurgy Research (CMR) Facility. Glovebox gloves in these facilities are exposed to elevated temperatures and exceptionally aggressive radiation environments (particulate {sup 239}Pu and {sup 238}Pu). Predictive models are needed to estimate glovebox glove service lifetimes, i.e. change-out intervals. Towards this aim aging studies have been initiated that correlate changes in mechanical (physical) properties with degradation chemistry. This present work derives glovebox glove change intervals based on previously reported mechanical data of thermally aged hypalon glove samples. Specifications for 30 mil tri-layered hypalon/lead glovebox gloves (TLH) and 15 mil hypalon gloves (HYP) have already been established. The relevant mechanical properties are shown on Table 1. Tensile strength is defined as the maximum load applied in breaking a tensile test piece divided by the original cross-sectional area of the test piece (Also termed maximum stress and ultimate tensile stress). Ultimate elongation is the elongation at time of rupture (Also termed maximum strain). The specification for the tensile test and ultimate elongation are the minimum acceptable values. In addition, the ultimate elongation must not vary 20% from the original value. In order to establish a service lifetimes for glovebox gloves in a thermal environment, the mechanical properties of glovebox glove materials were studied.

  2. Automated, High Temperature Furnace for Glovebox Operation

    International Nuclear Information System (INIS)

    Neikirk, K.

    2001-01-01

    The U.S. Department of Energy will immobilize excess plutonium in the proposed Plutonium Immobilization Plant (PIP) at the Savannah River Site (SRS) as part of a two track approach for the disposition of weapons usable plutonium. As such, the Department of Energy is funding a development and testing effort for the PIP. This effort is being performed jointly by Lawrence Livermore National Laboratory (LLNL), Westinghouse Savannah River Company (WSRC), Pacific Northwest National Laboratory (PNNL), and Argonne National Laboratory (ANL). The Plutonium Immobilization process involves the disposition of excess plutonium by incorporation into ceramic pucks. As part of the immobilization process, furnaces are needed for sintering the ceramic pucks. The furnace being developed for puck sintering is an automated, bottom loaded furnace with insulting package and resistance heating elements located within a nuclear glovebox. Other furnaces considered for the application include retort furnaces and pusher furnaces. This paper, in part, will discuss the furnace technologies considered and furnace technology selected to support reliable puck sintering in a glovebox environment. Due to the radiation levels and contamination associated with the plutonium material, the sintering process will be fully automated and contained within nuclear material gloveboxes. As such, the furnace currently under development incorporates water and air cooling to minimize heat load to the glovebox. This paper will describe the furnace equipment and systems needed to employ a fully automated puck sintering process within nuclear gloveboxes as part of the Plutonium Immobilization Plant

  3. Develop and Manufacture an Ergonomically Sound Glovebox Glove Report

    Energy Technology Data Exchange (ETDEWEB)

    Lawton, Cindy M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-10-18

    Ergonomic injury and radiation exposure are two safety concerns for the Plutonium Facility at Los Alamos National Laboratory (LANL). This facility employs the largest number of gloveboxes (GB) at LANL with approximately 6000 gloves installed. The current GB glove design dates back to the 1960’s and is not based on true hand anatomy, revealing several issues: short fingers, inappropriate length from the wrist to finger webbing, nonexistent joint angles and incorrect thumb placement. These design flaws are directly related to elbow (lateral epicondylitis) and thumb (DeQuervain’s tenosynovitis) injuries. The current design also contributes to increased wear on the glove, causing unplanned glove openings (failures) which places workers at risk of exposure. An improved glovebox glove design has three significant benefits: 1) it will reduce the risk of injury, 2) it will improve comfort and productivity, and 3) it will reduce the risk of a glovebox failures. The combination of these three benefits has estimated savings of several million dollars. The new glove design incorporated the varied physical attributes of workers ranging from the 5th percentile female to the 95th percentile male. Anthropometric hand dimensions along with current GB worker dimensions were used to develop the most comprehensive design specifications for the new glove. Collaboration with orthopedic hand surgeons also provided major contributtions to the design. The new glovebox glove was developed and manufactured incorporating over forty dimensions producing the most comprehensive ergonomically sound design. The new design received a LANL patent (patent attorney docket No: LANS 36USD1 “Protective Glove”, one of 20 highest patents awarded by the Richard P. Feynman Center for Innovation. The glove dimensions were inputed into a solid works model which was used to produce molds. The molds were then shipped to a glove manufacturer for production of the new glovebox gloves. The new

  4. 2014 AFCI Glovebox Event Executive Summary

    International Nuclear Information System (INIS)

    Campbell, Joseph Lenard

    2016-01-01

    One of the primary INL missions is to support development of advanced fuels with the goal of creating reactor fuels that produce less waste and are easier to store. The Advanced Fuel Cycle Initiative (AFCI) Glovebox in the Fuel Manufacturing Facility (FMF) is used for several fuel fabrication steps that involve transuranic elements, including americium. The AFCI glove box contains equipment used for fuel fabrication, including an arc melter - a small, laboratory-scale version of an electric arc furnace used to make new metal alloys for research - and an americium distillation apparatus. This overview summarizes key findings related to the investigation into the releases of airborne radioactivity that occurred in the AFCI glovebox room in late August and early September 2014. The full report (AFCI Glovebox Radiological Release - Evaluation, Corrective Actions and Testing, INL/INL-15-36996) provides details of the identified issues, corrective actions taken as well as lessons learned

  5. Chloride-catalyzed corrosion of plutonium in glovebox atmospheres

    International Nuclear Information System (INIS)

    Burgess, M.; Haschke, J.M.; Allen, T.H.; Morales, L.A.; Jarboe, D.M.; Puglisi, C.V.

    1998-04-01

    Characterization of glovebox atmospheres and the black reaction product formed on plutonium surfaces shows that the abnormally rapid corrosion of components in the fabrication line is consistent with a complex salt-catalyzed reaction involving gaseous hydrogen chloride (HCl) and water. Analytical data verify that chlorocarbon and HCl vapors are presented in stagnant glovebox atmospheres. Hydrogen chloride concentrations approach 7 ppm at some locations in the glovebox line. The black corrosion product is identified as plutonium monoxide monohydride (PuOH), a product formed by hydrolysis of plutonium in liquid water and salt solutions at room temperature. Plutonium trichloride (PuCl 3 ) produced by reaction of HCl at the metal surface is deliquescent and apparently forms a highly concentrated salt solution by absorbing moisture from the glovebox atmosphere. Rapid corrosion is attributed to the ensuing salt-catalyzed reaction between plutonium and water. Experimental results are discussed, possible involvement of hydrogen fluoride (HF) is examined, and methods of corrective action are presented in this report

  6. Scrap of gloveboxes No. 801-W and No. 802-W

    CERN Document Server

    Ohuchi, S; Kurosawa, M; Okane, S; Usui, T

    2002-01-01

    Both gloveboxes No. 801-W for measuring samples of uranium or plutonium and No. 802-W for analyzing the quantity of uranium or plutonium are established at twenty five years ago in the analyzing room No. 108 of Plutonium Fuel Research Facility. It was planned to scrap the gloveboxes and to establish new gloveboxes. This report describes the technical view of the scrapping works.

  7. Dexterity tests data contribute to reduction in leaded glovebox gloves use

    Energy Technology Data Exchange (ETDEWEB)

    Cournoyer, Michael E [Los Alamos National Laboratory; Lawton, Cindy M [Los Alamos National Laboratory; Castro, Amanda M [Los Alamos National Laboratory

    2008-01-01

    Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (TA-55) involve working with various amounts of plutonium and other highly toxic, alphaemitting materials. The spread of radiological contamination on surfaces and airborne contamination and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes. Through an integrated approach, controls have been developed and implemented through an efficient Glovebox Glove Integrity Program (GGJP). A key element of this program is to consider measures that lower the overall risk of glovebox operations. Line management owning glovebox processes through this program make decisions on which type of glovebox gloves (the weakest component of this safety significant system) would perform in these aggressive environments. As Low As Reasonably Achievable (ALARA) considerations must be balanced with glove durability and worker dexterity, both of which affect the final overall risk of the operation. In the past, lead-loaded (leaded) glovebox gloves made from Hypalon(reg.) had been the workhorse of programmatic operations at TA-55. Replacing leaded gloves with unleaded gloves for certain operations would lower the overall risk as well as reduced the amount of mixed TRU waste. This effort contributes to Los Alamos National Laboratory Continuous Improvement Program by improving the efficiency, cost effectiveness, and formality of glovebox operations. In the following report, the pros and cons of wearing leaded glovebox gloves, the effect of leaded gloves versus unleaded gloves on task performance using standard dexterity tests, the justification for switching from leaded to unleaded gloves, and pollution prevention benefits of this dramatic change in the glovebox system are presented.

  8. Decrease the Number of Glovebox Glove Breaches and Failures

    Energy Technology Data Exchange (ETDEWEB)

    Hurtle, Jackie C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2013-12-24

    Los Alamos National Laboratory (LANL) is committed to the protection of the workers, public, and environment while performing work and uses gloveboxes as engineered controls to protect workers from exposure to hazardous materials while performing plutonium operations. Glovebox gloves are a weak link in the engineered controls and are a major cause of radiation contamination events which can result in potential worker exposure and localized contamination making operational areas off-limits and putting programmatic work on hold. Each day of lost opportunity at Technical Area (TA) 55, Plutonium Facility (PF) 4 is estimated at $1.36 million. Between July 2011 and June 2013, TA-55-PF-4 had 65 glovebox glove breaches and failures with an average of 2.7 per month. The glovebox work follows the five step safety process promoted at LANL with a decision diamond interjected for whether or not a glove breach or failure event occurred in the course of performing glovebox work. In the event that no glove breach or failure is detected, there is an additional decision for whether or not contamination is detected. In the event that contamination is detected, the possibility for a glove breach or failure event is revisited.

  9. Comparison of deliverable and exhaustible pressurized air flow rates in laboratory gloveboxes

    International Nuclear Information System (INIS)

    Compton, J.A.

    1994-01-01

    Calculations were performed to estimate the maximum credible flow rates of pressurized air into Plutonium Process Support Laboratories gloveboxes. Classical equations for compressible fluids were used to estimate the flow rates. The calculated maxima were compared to another's estimates of glovebox exhaust flow rates and corresponding glovebox internal pressures. No credible pressurized air flow rate will pressurize a glovebox beyond normal operating limits. Unrestricted use of the pressurized air supply is recommended

  10. WRAP low level waste (LLW) glovebox acceptance test report

    International Nuclear Information System (INIS)

    Leist, K.J.

    1998-01-01

    In June 28, 1997, the Low Level Waste (LLW) glovebox was tested using glovebox acceptance test procedure 13031A-85. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, lidder/delidder device and the supercompactor were also conducted. As of November 24, 1997, 2 of the 131 test exceptions that affect the LLW glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test Exceptions are provided as appendices to this report

  11. W-026, transuranic waste (TRU) glovebox acceptance test report

    International Nuclear Information System (INIS)

    Leist, K.J.

    1998-01-01

    On July 18, 1997, the Transuranic (TRU) glovebox was tested using glovebox acceptance test procedure 13021A-86. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, sorting table, lidder/delidder device and the TRU empty drum compactor were also conducted. As of February 25, 1998, 10 of the 102 test exceptions that affect the TRU glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test exceptions are provided as appendices to this report

  12. WRAP low level waste (LLW) glovebox acceptance test report

    Energy Technology Data Exchange (ETDEWEB)

    Leist, K.J.

    1998-02-17

    In June 28, 1997, the Low Level Waste (LLW) glovebox was tested using glovebox acceptance test procedure 13031A-85. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, lidder/delidder device and the supercompactor were also conducted. As of November 24, 1997, 2 of the 131 test exceptions that affect the LLW glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test Exceptions are provided as appendices to this report.

  13. Design/build/mockup of the Waste Isolation Pilot Plant gas generation experiment glovebox

    International Nuclear Information System (INIS)

    Rosenberg, K.E.; Benjamin, W.W.; Knight, C.J.; Michelbacher, J.A.

    1996-01-01

    A glovebox was designed, fabricated, and mocked-up for the WIPP Gas Generation Experiments (GGE) being conducted at ANL-W. GGE will determine the gas generation rates from materials in contact handled transuranic waste at likely long term repository temperature and pressure conditions. Since the customer's schedule did not permit time for performing R ampersand D of the support systems, designing the glovebox, and fabricating the glovebox in a serial fashion, a parallel approach was undertaken. As R ampersand D of the sampling system and other support systems was initiated, a specification was written concurrently for contracting a manufacturer to design and build the glovebox and support equipment. The contractor understood that the R ampersand D being performed at ANL-W would add additional functional requirements to the glovebox design. Initially, the contractor had sufficient information to design the glovebox shell. Once the shell design was approved, ANL-W built a full scale mockup of the shell out of plywood and metal framing; support systems were mocked up and resultant information was forwarded to the glovebox contractor to incorporate into the design. This approach resulted in a glovebox being delivered to ANL-W on schedule and within budget

  14. Survey of Technologies to Support Reuse of Gloveboxes at LANL TA-55

    International Nuclear Information System (INIS)

    Cadwallader, L.C.; Pinson, P.A.

    1998-01-01

    This report is a summary of ideas and technologies available to support reuse of plutonium gloveboxes at the Los Alamos National Laboratory (LANL) Technical Area 55 (TA-55). This work is the second of two deliverables in the task to enhance glovebox design for longevity and reusability at TA-55. The report presents several design change suggestions to be evaluated for their feasibility by LANL glovebox designers. The report also describes some techniques to be evaluated by LANL for their usefulness in reducing glovebox waste

  15. The Virtual Glovebox (VGX): An Immersive Simulation System for Training Astronauts to Perform Glovebox Experiments in Space

    Science.gov (United States)

    Smith, Jeffrey D.; Dalton, Bonnie (Technical Monitor)

    2002-01-01

    The era of the International Space Station (ISS) has finally arrived, providing researchers on Earth a unique opportunity to study long-term effects of weightlessness and the space environment on structures, materials and living systems. Many of the physical, biological and material science experiments planned for ISS will require significant input and expertise from astronauts who must conduct the research, follow complicated assay procedures and collect data and samples in space. Containment is essential for Much of this work, both to protect astronauts from potentially harmful biological, chemical or material elements in the experiments as well as to protect the experiments from contamination by air-born particles In the Space Station environment. When astronauts must open the hardware containing such experiments, glovebox facilities provide the necessary barrier between astronaut and experiment. On Earth, astronauts are laced with the demanding task of preparing for the many glovebox experiments they will perform in space. Only a short time can be devoted to training for each experimental task and gl ovebox research only accounts for a small portion of overall training and mission objectives on any particular ISS mission. The quality of the research also must remain very high, requiring very detailed experience and knowledge of instrumentation, anatomy and specific scientific objectives for those who will conduct the research. This unique set of needs faced by NASA has stemmed the development of a new computer simulation tool, the Virtual Glovebox (VGB), which is designed to provide astronaut crews and support personnel with a means to quickly and accurately prepare and train for glovebox experiments in space.

  16. Design criteria for plutonium gloveboxes

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The standard defines criteria for the design of glovebox systems to be used for the handling of plutonium in any form or isotopic composition or when mixed with other elements or compounds. The glovebox system is a series of physical barriers provided with glove ports and gloves, through which process and maintenance operations may be performed, together with an operating ventilation system. The system minimizes the potential for release of radioactive material to the environment, protects operators from contamination, and mitigates the consequences of abnormal condiations. The standard covers confinement, construction, materials, windows, glove ports, gloves, equipment insertion and removal, lighting, ventilation, fire protection, criticality prevention, services and utilities, radiation shielding, waste systems, monitoring and alarm systems, safeguards, quality assurance, and decommissioning

  17. Glovebox characterization and barrier integrity testing using fluorescent powder

    International Nuclear Information System (INIS)

    Wahlquist, D.R.

    1996-01-01

    This paper presents a method for characterizing the spread of contamination and testing the barrier integrity of a new glovebox during material transfer operations and glove change-outs using fluorescent powder. Argonne National Laboratory-West has performed this test on several new gloveboxes prior to putting them into service. The test is performed after the glovebox has been leak tested and all systems have been verified to be operational. The purpose of the test is to show that bag-in/bag-out operations and glove change-outs can be accomplished without spreading the actual contaminated material to non-contaminated areas. The characterization test also provides information as to where contamination might be expected to build-up during actual operations. The fluorescent powder is used because it is easily detectable using an ultra-violet light and disperses in a similar fashion to radioactive material. The characterization and barrier integrity test of a glovebox using fluorescent powder provides a visual method of determining areas of potential contamination accumulation and helps evaluate the ability to perform clean transfer operations and glove change-outs

  18. DISPOSITION PATHS FOR ROCKY FLATS GLOVEBOXES: EVALUATING OPTIONS

    International Nuclear Information System (INIS)

    Lobdell, D.; Geimer, R.; Larsen, P.; Loveland, K.

    2003-01-01

    The Kaiser-Hill Company, LLC has the responsibility for closure activities at the Rocky Flats Environmental Technology Site (RFETS). One of the challenges faced for closure is the disposition of radiologically contaminated gloveboxes. Evaluation of the disposition options for gloveboxes included a detailed analysis of available treatment capabilities, disposal facilities, and lifecycle costs. The Kaiser-Hill Company, LLC followed several processes in determining how the gloveboxes would be managed for disposition. Currently, multiple disposition paths have been chosen to accommodate the needs of the varying styles and conditions of the gloveboxes, meet the needs of the decommissioning team, and to best manage lifecycle costs. Several challenges associated with developing a disposition path that addresses both the radiological and RCRA concerns as well as offering the most cost-effective solution were encountered. These challenges included meeting the radiological waste acceptance criteria of available disposal facilities, making a RCRA determination, evaluating treatment options and costs, addressing void requirements associated with disposal, and identifying packaging and transportation options. The varying disposal facility requirements affected disposition choices. Facility conditions that impacted decisions included radiological and chemical waste acceptance criteria, physical requirements, and measurement for payment options. The facility requirements also impacted onsite activities including management strategies, decontamination activities, and life-cycle cost

  19. Follow-On Vapor Containment Tests of the Rapid Response System Glovebox

    National Research Council Canada - National Science Library

    Arca, Victor

    1997-01-01

    ...) glovebox in April 1996. The tests were conducted by generating a cloud of the simulant methyl salicylate inside the glovebox and measuring the concentration of any simulant that permeated to the operator workspace...

  20. Dexterity Test Data Contribute To Reduction in Leaded Glovebox Glove Use

    International Nuclear Information System (INIS)

    Cournoyer, M.E.; Lawton, C.M.; Castro, A.M.; Costigan, S.A.; Schreiber, S.

    2009-01-01

    Programmatic operations at the Los Alamos National Laboratory Plutonium Facility (TA-55) involve working with various amounts of plutonium and other highly toxic, alpha-emitting materials. The spread of radiological contamination on surfaces, airborne contamination, and excursions of contaminants into the operator's breathing zone are prevented through the use of a variety of gloveboxes. Using an integrated approach, controls have been developed and implemented through an efficient Glovebox Glove Integrity Program. A key element of this program is to consider measures that lower the overall risk of glovebox operations. Line management who own glovebox processes through this program make decisions on which type of glovebox gloves (hereafter referred to as gloves), the weakest component of this safety-significant system, would perform best in these aggressive environments. As Low as Reasonably Achievable considerations must be balanced with glove durability and worker dexterity, both of which affect the final overall risk of the operation. In the past, lead-loaded (leaded) gloves made from Hypalon R were the primary glove for programmatic operations at TA-55. Replacing leaded gloves with unleaded gloves for certain operations would lower the overall risk as well as reduce the amount of mixed transuranic waste. This effort contributes to the Los Alamos National Laboratory Continuous Improvement Program by improving the efficiency, cost-effectiveness, and formality of glovebox operations. In this report, the pros and cons of wearing leaded gloves, the effect of leaded gloves versus unleaded gloves on task performance using standard dexterity tests, the justification for switching from leaded to unleaded gloves, and the pollution prevention benefits of this dramatic change in the glovebox system are presented. (authors)

  1. Macro and Micro Remote Viewing of Objects in Sealed Gloveboxes

    International Nuclear Information System (INIS)

    Heckendorn, F.M.

    2004-01-01

    The Savannah River Site uses sophisticated glovebox facilities to process and analyze material that is radiologically contaminated or that must be protected from contamination by atmospheric gases. The analysis can be visual, non destructive measurement, or destructive measurement, and allows for the gathering of information that would otherwise not be obtainable. Macro and Micro systems that cover a range of 2X to 400X magnifications with a robust system compatible with the harsh glovebox environment were installed. Remote video inspection systems were developed and deployed in Savannah River Site glovebox facilities that provide high quality or mega-pixel quality remote views, for remote inspections. The specialized video systems that are the subject of this report exhibited specialized field application of remote video/viewing techniques by expanding remote viewing to high and very high quality viewing in gloveboxes. This technological enhancement will allow the gathering of precision information that is otherwise not available

  2. Tritium stripping in a nitrogen glovebox using SAES St 198

    International Nuclear Information System (INIS)

    Klein, J.E.; Wermer, J.R.

    1994-01-01

    SAES metal getter material St 198 was chosen for glovebox stripper tests to evaluate its effectiveness of removing tritium from a nitrogen atmosphere. The St 198 material is unique from a number of other metal hydride-based getter materials in that it is relatively inert to nitrogen and can thus be used in nitrogen glovebox atmospheres. Six tritium stripper experiments which mock-up the use of a SAES St 198 stripper bed for a full-scale (10,500 liter) nitrogen glovebox have been completed. Experiments consisted of a release of small quantity of protium/deuterium spiked with tritium which were scaled to simulate tritium releases of 0.1 g., 1.0 g., and 10 g. into the glovebox. The tritium spike allows detection using tritium ion chambers. The St 198 stripper system produced a reduction in tritium activity of approximately two orders of magnitude in 24 hours (6--8 atmosphere turn-overs) of stripper operation

  3. Unique features in the ARIES glovebox line

    International Nuclear Information System (INIS)

    Martinez, H.E.; Brown, W.G.; Flamm, B.; James, C.A.; Laskie, R.; Nelson, T.O.; Wedman, D.E.

    1998-01-01

    A series of unique features have been incorporated into the Advanced Recovery and Integrated Extraction System (ARIES) at the Los Alamos National Laboratory, TA-55 Plutonium Facility. The features enhance the material handling in the process of the dismantlement of nuclear weapon primaries in the glovebox line. Incorporated into these features are the various plutonium process module's different ventilation zone requirements that the material handling systems must meet. These features include a conveyor system that consists of a remotely controlled cart that transverses the length of the conveyor glovebox, can be operated from a remote location and can deliver process components to the entrance of any selected module glovebox. Within the modules there exists linear motion material handling systems with lifting hoist, which are controlled via an Allen Bradley control panel or local control panels. To remove the packaged products from the hot process line, the package is processed through an air lock/electrolytic decontamination process that removes the radioactive contamination from the outside of the package container and allows the package to be removed from the process line

  4. Rotator Cuff Strength Ratio and Injury in Glovebox Workers

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, Amelia M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-01-30

    Rotator cuff integrity is critical to shoulder health. Due to the high workload imposed upon the shoulder while working in an industrial glovebox, this study investigated the strength ratio of the rotator cuff muscles in glovebox workers and compared this ratio to the healthy norm. Descriptive statistics were collected using a short questionnaire. Handheld dynamometry was used to quantify the ratio of forces produced in the motions of shoulder internal and external rotation. Results showed this population to have shoulder strength ratios that were significantly different from the healthy norm. The deviation from the normal ratio demonstrates the need for solutions designed to reduce the workload on the rotator cuff musculature of glovebox workers in order to improve health and safety. Assessment of strength ratios can be used to screen for risk of symptom development.

  5. Requalification of the 235-F Metallograph Facility gloveboxes for use in the 773-A plutonium immobilization demonstration

    International Nuclear Information System (INIS)

    Hinds, S.S.; Hidlay, J.

    1997-01-01

    A concern has been identified regarding the viability of redesigning and requalifying existing glovebox lines for use as glovebox lines integral to future mission activities in the 773-A laboratory building at the Savannah River Site (SRS). The Bechtel Savannah River Inc. (BSRI) design engineering team has been requested to perform an evaluation which would investigate the reuse of these existing gloveboxes versus the procurement of completely new glovebox systems. The existing glovebox lines were manufactured for the Plutonium (Pu) Metallograph Facility, Project 3253, located in building 235-F at SRS. These gloveboxes were designed as independent, fully functional Pu 'metal' and Pu 'oxide' processing glovebox systems for this facility. These gloveboxes, although fully installed, have never processed radioactive material. The proposed use for these gloveboxes are: (1) to utilize the Pu 'metal' glovebox system for the primary containment associated with the Pre-Processing/Re-Processing Laboratory for obtaining radioactive glass compound viscometer analysis and (2) to utilize the Pu 'oxide' glovebox system for primary containment associated with the Pu 'Can in Can' Demonstration for proof of principle testing specific to long term Pu immobilization and storage technology. This report presents objective evidence that supports the engineering judgment indicating the existing gloveboxes can be requalified for the proposed uses indicated above. SRS has the ability to duplicate the test parameters, with site forces, that will meet or exceed the identical acceptance criteria established to qualify the existing gloveboxes. The qualification effort will be a documented procedure using the leak test criteria characteristic of the original glovebox purchase. Two equivalent tests will be performed, one for post modification leak test acceptance and one for post installation leak test acceptance. (Abstract Truncated)

  6. Glovebox enclosed dc plasma source for the determination of metals in plutonium

    International Nuclear Information System (INIS)

    Morris, W.F.

    1986-01-01

    The direct current plasma source of a Beckman Spectraspan IIIB emission spectrometer was enclosed in a glovebox at Lawrence Livermore National Laboratory in December 1982. Since that time, the system has been used for the routine determination of alloy and impurity metals in plutonium. This paper presents the systematic steps involved in developing the glovebox and gives information regarding performance of the plasma in the glovebox and the effectiveness of containment of plutonium. 8 refs., 9 figs., 3 tabs

  7. Glovebox glove change program at Technical Area 55, Los Alamos National Laboratory

    International Nuclear Information System (INIS)

    Olivas, J.D.; Burkett, B.O.; Weier, D.R.

    1992-01-01

    A formal glovebox glove change program is planned for the the gloveboxes in technical area 55 at the Los Alamos National laboratory. The program will increase worker safety by reducing the chance of having worn out gloves in service. The Los Alamos program is based on a similar successful program at the Rocky Flats Plant in Golden, Colorado. Glove change frequencies at Rocky Flats were determined statistically, and are based on environmental factors the glovebox gloves are subjected to

  8. Issues for reuse of gloveboxes at LANL TA-55

    Energy Technology Data Exchange (ETDEWEB)

    Cadwallader, L.C.; Pinson, P.A.; Miller, C.F.

    1998-08-01

    This report is a summary of issues that face plutonium glovebox designers and users at the Los Alamos National Laboratory (LANL) Technical Area 55 (TA-55). Characterizing the issues is a step in the task of enhancing the next generation glovebox design to minimize waste streams while providing the other design functions. This report gives an initial assessment of eight important design and operation issues that can benefit from waste minimization.

  9. Issues for reuse of gloveboxes at LANL TA-55

    International Nuclear Information System (INIS)

    Cadwallader, L.C.; Pinson, P.A.; Miller, C.F.

    1998-08-01

    This report is a summary of issues that face plutonium glovebox designers and users at the Los Alamos National Laboratory (LANL) Technical Area 55 (TA-55). Characterizing the issues is a step in the task of enhancing the next generation glovebox design to minimize waste streams while providing the other design functions. This report gives an initial assessment of eight important design and operation issues that can benefit from waste minimization

  10. Design improvements for gloveboxes used [in] 238PuO2 process operations

    International Nuclear Information System (INIS)

    George, T.G.

    1997-01-01

    238 PuO 2 process operations are housed in a complex of 76 gloveboxes and introductory hoods connected by means of an overhead trolley housed in a tunnel. Because a significant number of the gloveboxes used for 238 PuO 2 processing were installed before the original startup of the facility in 1978, they have been in service for nearly 20 years. During a recent heat source production campaign, numerous contamination releases in the 238 PuO 2 processing area were traced to degraded elastomer gaskets used for glovebox connections, and attachment of feed-throughs, service panels, and windows. Evaluation of the degraded gaskets revealed that a combination of radiolytic degradation related to the high specific activity of 238 Pu, and extended service at high altitude in a low (to extremely low) humidity environment had resulted in accelerated gasket aging. However, it was also apparent that gasket design was the most important factor in actual contamination release. All of the contamination releases that were traced to degraded gaskets occurred in variations of a design that used a spline to expand an elastomeric gasket into the space between a connecting flange, window, or service panel, and a glovebox opening. No contamination releases were traced to the gasket design that employed bolted clamps to compress the gasket between a connecting flange, window, or panel, and the exterior surface of a glovebox opening. As a result of these findings, the Actinide Ceramics group at LANL (NMT-9) has initiated a routine replacement and upgrade program to replace aging gloveboxes. All of the new gloveboxes will utilize the preferred gasket design, which is expected to reduce the number and frequency of contamination releases

  11. Constant depression fan system a novel glovebox ventilation system

    International Nuclear Information System (INIS)

    Milliner, W.V.

    1995-01-01

    In a conventional glovebox ventilation system the depression within the glovebox under normal operation is controlled by instrumentation. In the event of a breach the pressure within the box rises to atmospheric pressure, this pressure rise is detected by instrumentation which in turn operates a quick opening damper in a high depression extract to achieve a 1 metre/sec (200 fpm) inflow through the breach, which can take up to 2 seconds to establish. This system, although widely used, suffers from two distinct drawbacks: It takes a finite time to achieve the containment velocity of 1 metre/sec. It relies upon instrumentation to achieve its objectives. A new glovebox ventilation system has been developed by AWE to overcome these drawbacks. This is the Constant Depression Fan System (CDFS) which is based on an extract fan with a flat characteristic. This achieves all the requirements for the ventilation of gloveboxes and has the advantages that: It has only one moving part - the extract fan. It requires NO INSTRUMENTATION to achieve its objectives. It achieves the containment velocity of 1 metre/sec in the shortest possible time - approximately 0.2 seconds - and tests have shown that containment is maintained under breach conditions. Thus the CDFS is SAFER, SIMPLER and MORE RELIABLE

  12. Constant depression fan system a novel glovebox ventilation system

    Energy Technology Data Exchange (ETDEWEB)

    Milliner, W.V. [AME plc., Aldermaston (United Kingdom)

    1995-02-01

    In a conventional glovebox ventilation system the depression within the glovebox under normal operation is controlled by instrumentation. In the event of a breach the pressure within the box rises to atmospheric pressure, this pressure rise is detected by instrumentation which in turn operates a quick opening damper in a high depression extract to achieve a 1 metre/sec (200 fpm) inflow through the breach, which can take up to 2 seconds to establish. This system, although widely used, suffers from two distinct drawbacks: It takes a finite time to achieve the containment velocity of 1 metre/sec. It relies upon instrumentation to achieve its objectives. A new glovebox ventilation system has been developed by AWE to overcome these drawbacks. This is the Constant Depression Fan System (CDFS) which is based on an extract fan with a flat characteristic. This achieves all the requirements for the ventilation of gloveboxes and has the advantages that: It has only one moving part - the extract fan. It requires NO INSTRUMENTATION to achieve its objectives. It achieves the containment velocity of 1 metre/sec in the shortest possible time - approximately 0.2 seconds - and tests have shown that containment is maintained under breach conditions. Thus the CDFS is SAFER, SIMPLER and MORE RELIABLE.

  13. Standard guide for design criteria for plutonium gloveboxes

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This guide defines criteria for the design of glovebox systems to be used for the handling of plutonium in any chemical or physical form or isotopic composition or when mixed with other elements or compounds. Not included in the criteria are systems auxiliary to the glovebox systems such as utilities, ventilation, alarm, and waste disposal. Also not addressed are hot cells or open-face hoods. The scope of this guide excludes specific license requirements relating to provisions for criticality prevention, hazards control, safeguards, packaging, and material handling. Observance of this guide does not relieve the user of the obligation to conform to all federal, state, and local regulations for design and construction of glovebox systems. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user...

  14. Seismic analysis of safety class 1 incinerator glovebox in building 232-Z 200 W Area

    International Nuclear Information System (INIS)

    Ocoma, E.C.

    1994-09-01

    This report documents the seismic evaluation for the existing safety class 1 incinerator glovebox in 232Z Building. The glovebox is no longer in use and most of the internal mechanical equipment have been removed. However, the insulation firebricks are still in the glovebox for proper disposal

  15. Ventilation of gloveboxes and containment shells

    International Nuclear Information System (INIS)

    Guetron, R.

    1984-01-01

    In this paper are defined fundamental principles for the ventilation of containment enclosures and gloveboxes, and examined criteria required to maintain containment in normal or accidental conditions. Dimensioning of ventilation network and associated equipment (adjustement and filtering devices). Some examples are given [fr

  16. The OPAL phase III microvertex detector

    International Nuclear Information System (INIS)

    De Jong, S.

    1997-01-01

    A description of the OPAL Phase III microvertex detector is given. Special emphasis is put on problems that have been encountered in the installation and operation of the different phases of the OPAL microvertex detector leading to the present Phase III detector and their cures. A short description of the new OPAL radiation monitoring and beam dump system is also given. (orig.)

  17. Ergonomic glovebox workspace layout tool and associated method of use

    Science.gov (United States)

    Roddy, Shannon Howard

    2018-02-20

    The present invention provides an elongate tool that aides in the placement of objects and machinery within a glovebox, such that the objects and machinery can be safely handled by a user. The tool includes a plurality of visual markings (in English units, metric units, other units, grooves, ridges, varying widths, etc.) that indicate distance from the user within the glovebox, optionally broken into placement preference zones that are color coded, grayscale coded, or the like.

  18. Design considerations for heated wells in gloveboxes

    International Nuclear Information System (INIS)

    Frigo, A. A.; Preuss, D. E.

    1999-01-01

    Heated wells in gloveboxes have been used for many years by the Argonne National Laboratory Chemical Technology Division for nuclear-technology, waste-management, chemical-technology, and analytical-chemistry research. These wells allow experiments to be isolated from the main working volume of the glovebox. In addition, wells, when sealed, allow experiments to be conducted under pressurized or vacuum conditions. Until recently, typical maximum operational temperatures were about 500 C. However, more recent research is requiring operational temperatures approaching 900 C. These new requirements pose interesting design challenges that must be resolved. Some problem areas include temperature effects on material properties, maintaining a seal, cooling selected areas, and minimizing stresses. This paper discusses issues related to these design challenges and the ways in which these issues have been resolved

  19. Dismantling techniques for plutonium-contaminated gloveboxes: experience from first year of decommissioning; Zerlegungstechniken fuer Pu-kontaminierte Handschuhkaesten: Erfahrungsbericht nach einem Jahr Rueckbau

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, R.; Faber, P. [Siemens Power Generation, Decommissioning Projects, Hanau (Germany)

    2003-07-01

    At the mixed-oxide (MOX) processing facility formerly operated by ALKEM GmbH in Hanau, Germany - which was taken over to Siemens in 1988 and renamed Siemens' Hanau Fuel Fabrication Plant, MOX facility - around 8500 kg of plutonium were processed to make MOX fuel rods and fuel assemblies since production started in 1965. After shutdown of the facility by the authorities in mid-1991 for political reasons, the remaining nuclear fuel materials were processed during the subsequent ''cleanout'' phase starting in 1997 into rods and assemblies suitable for long-term storage. The last step in cleanout consisted of ''flushing'' the production equipment with depleted uranium and thoroughly cleaning the gloveboxes. During cleanout around 700 kg of plutonium were processed in the form of mixed oxides. The cleanout phase including the subsequent cleaning and flushing operations ended on schedule in September 2001 without any significant problems. Starting in mid-1999, the various glovebox dismantling techniques were tested using uncontaminated components while cleanout was still in progress and then, once these trials had been successfully completed, further qualified through use on actual components. The pilot-phase trials required four separate licenses under Section 7, Subsection (3) of the German Atomic Energy Act. Thanks to detailed advance planning and experience from the pilot trials the individual dismantling steps could be described in sufficient detail for the highly complex German licensing procedure. The first partial license for decommissioning the MOX facility under Sec. 7, Subsec. (3) of the Atomic Energy Act was issued on May 28, 2001. It mainly covers dismantling of the interior equipment inside the gloveboxes a well as the gloveboxes themselves. Actual decommissioning work inside the former production areas of the MOX facility started on a large scale in early September 2001. (orig.)

  20. Automated, High Temperature Furnace for Glovebox Operation

    International Nuclear Information System (INIS)

    Neikirk, K.

    2001-01-01

    The Plutonium Immobilization Project (PIP), to be located at the Savannah River Site SRS, is a combined development and testing effort by Lawrence Livermore National Laboratory (LLNL), Westinghouse Savannah River Company (WSRC), Pacific Northwest National Laboratory (PNNL), Argonne National Laboratory (ANL), and the Australian National Science and Technology Organization (ANSTO). The Plutonium Immobilization process involves the disposition of excess plutonium by incorporation into ceramic pucks. As part of the immobilization process, furnaces are needed for sintering the ceramic pucks. The furnace being developed for puck sintering is an automated, bottom loaded furnace with insulating package and resistance heating elements located within a nuclear glovebox. Other furnaces types considered for the application include retort furnaces and pusher furnaces. This paper, in part, will discuss the furnace technologies considered and furnace technology selected to support reliable puck sintering in a glovebox environment

  1. Design improvements for gloveboxes used [in] {sup 238}PuO{sub 2} process operations

    Energy Technology Data Exchange (ETDEWEB)

    George, T.G. [Los Alamos National Lab., NM (United States). Nuclear Materials Technology Div.

    1997-09-01

    {sup 238}PuO{sub 2} process operations are housed in a complex of 76 gloveboxes and introductory hoods connected by means of an overhead trolley housed in a tunnel. Because a significant number of the gloveboxes used for {sup 238}PuO{sub 2} processing were installed before the original startup of the facility in 1978, they have been in service for nearly 20 years. During a recent heat source production campaign, numerous contamination releases in the {sup 238}PuO{sub 2} processing area were traced to degraded elastomer gaskets used for glovebox connections, and attachment of feed-throughs, service panels, and windows. Evaluation of the degraded gaskets revealed that a combination of radiolytic degradation related to the high specific activity of {sup 238}Pu, and extended service at high altitude in a low (to extremely low) humidity environment had resulted in accelerated gasket aging. However, it was also apparent that gasket design was the most important factor in actual contamination release. All of the contamination releases that were traced to degraded gaskets occurred in variations of a design that used a spline to expand an elastomeric gasket into the space between a connecting flange, window, or service panel, and a glovebox opening. No contamination releases were traced to the gasket design that employed bolted clamps to compress the gasket between a connecting flange, window, or panel, and the exterior surface of a glovebox opening. As a result of these findings, the Actinide Ceramics group at LANL (NMT-9) has initiated a routine replacement and upgrade program to replace aging gloveboxes. All of the new gloveboxes will utilize the preferred gasket design, which is expected to reduce the number and frequency of contamination releases.

  2. Applications of LabVIEW programming in a glovebox environment

    International Nuclear Information System (INIS)

    Evans, M.E.; Peralta, G.; Gray, D.

    1995-01-01

    When dealing with neutron radiation one of the keys to reducing worker exposure is to have as much distance and shielding between the radiation and the radiation worker as possible. Using a PC to control a process from a remote location allows the distance between the radiation worker and the radiation source to be increase. Increasing the distance at which radiation worker can control a process allows more shielding to be placed around the glovebox. There are many commercial packages that allow controlling remote processes with a PC. This paper shows how flexible the LabVIEW Graphical Programming Language can be in implementing the remote control of glovebox process

  3. Failures in Phase III: Causes and Consequences.

    Science.gov (United States)

    Seruga, Bostjan; Ocana, Alberto; Amir, Eitan; Tannock, Ian F

    2015-10-15

    Phase III randomized controlled trials (RCT) in oncology fail to lead to registration of new therapies more often than RCTs in other medical disciplines. Most RCTs are sponsored by the pharmaceutical industry, which reflects industry's increasing responsibility in cancer drug development. Many preclinical models are unreliable for evaluation of new anticancer agents, and stronger evidence of biologic effect should be required before a new agent enters the clinical development pathway. Whenever possible, early-phase clinical trials should include pharmacodynamic studies to demonstrate that new agents inhibit their molecular targets and demonstrate substantial antitumor activity at tolerated doses in an enriched population of patients. Here, we review recent RCTs and found that these conditions were not met for most of the targeted anticancer agents, which failed in recent RCTs. Many recent phase III RCTs were initiated without sufficient evidence of activity from early-phase clinical trials. Because patients treated within such trials can be harmed, they should not be undertaken. The bar should also be raised when making decisions to proceed from phase II to III and from phase III to marketing approval. Many approved agents showed only better progression-free survival than standard treatment in phase III trials and were not shown to improve survival or its quality. Introduction of value-based pricing of new anticancer agents would dissuade the continued development of agents with borderline activity in early-phase clinical trials. When collaborating with industry, oncologists should be more critical and better advocates for cancer patients. ©2015 American Association for Cancer Research.

  4. Organic Contamination Baseline Study on NASA JSC Astromaterial Curation Gloveboxes

    Science.gov (United States)

    Calaway, Michael J.; Allton, J. H.; Allen, C. C.; Burkett, P. J.

    2013-01-01

    Future planned sample return missions to carbon-rich asteroids and Mars in the next two decades will require strict handling and curation protocols as well as new procedures for reducing organic contamination. After the Apollo program, astromaterial collections have mainly been concerned with inorganic contamination [1-4]. However, future isolation containment systems for astromaterials, possibly nitrogen enriched gloveboxes, must be able to reduce organic and inorganic cross-contamination. In 2012, a baseline study was orchestrated to establish the current state of organic cleanliness in gloveboxes used by NASA JSC astromaterials curation labs that could be used as a benchmark for future mission designs.

  5. CSER 98-003: criticality safety evaluation report for PFP glovebox HC-21A with button can opening

    International Nuclear Information System (INIS)

    ERICKSON, D.G.

    1999-01-01

    Glovebox HC-21A is an enclosure where cans containing plutonium metal buttons or other plutonium bearing materials are prepared for thermal stabilization in the muffle furnaces. The Inert Atmosphere Confinement (IAC), a new feature added to Glovebox HC-21 A, allows the opening of containers suspected of containing hydrided plutonium metal. The argon atmosphere in the IAC prevents an adverse reaction between oxygen and the hydride. The hydride is then stabilized in a controlled manner to prevent glovebox over pressurization. After removal from the containers, the plutonium metal buttons or plutonium bearing materials will be placed into muffle furnace boats and then be sent to one of the muffle furnace gloveboxes for stabilization. The materials allowed to be brought into Glovebox HC-21A are limited to those with a hydrogen to fissile atom ratio (H/X) ≤ 20. Glovebox HC-21A is classified as a DRY glovebox, meaning it has no internal liquid lines, and no free liquids or solutions are allowed to be introduced. The double contingency principle states that designs shall incorporate sufficient factors of safety to require at least two unlikely, independent, and concurrent changes in process conditions before a criticality accident is possible. This criticality safety evaluation report (CSER) shows that the operations to be performed in this glovebox are safe from a criticality standpoint. No single identified event that causes criticality controls to be lost exceeded the criticality safety limit of k eff = 0.95 (including uncertainties). Therefore, this CSER meets the requirements for a criticality analysis contained in the Hanford Site Nuclear Criticality Safety Manual, HNF-PRO-334, and meets the double contingency principle

  6. CSER 98-003: Criticality safety evaluation report for PFP glovebox HC-21A with button can opening

    International Nuclear Information System (INIS)

    ERICKSON, D.G.

    1999-01-01

    Glovebox HC-21A is an enclosure where cans containing plutonium metal buttons or other plutonium bearing materials are prepared for thermal stabilization in the muffle furnaces. The Inert Atmosphere Confinement (IAC), a new feature added to Glovebox HC-21A, allows the opening of containers suspected of containing hydrided plutonium metal. The argon atmosphere in the IAC prevents an adverse reaction between oxygen and the hydride. The hydride is then stabilized in a controlled manner to prevent glovebox over pressurization. After removal from the containers, the plutonium metal buttons or plutonium bearing materials will be placed into muffle furnace boats and then be sent to one of the muffle furnace gloveboxes for stabilization. The materials allowed to be brought into GloveboxHC-21 A are limited to those with a hydrogen to fissile atom ratio (H/X) ≤ 20. Glovebox HC-21A is classified as a DRY glovebox, meaning it has no internal liquid lines, and no free liquids or solutions are allowed to be introduced. The double contingency principle states that designs shall incorporate sufficient factors of safety to require at least two unlikely, independent, and concurrent changes in process conditions before a criticality accident is possible. This criticality safety evaluation report (CSER) shows that the operations to be performed in this glovebox are safe from a criticality standpoint. No single identified event that causes criticality controls to be lost exceeded the criticality safety limit of k eff = 0.95. Therefore, this CSER meets the requirements for a criticality analysis contained in the Hanford Site Nuclear Criticality Safety Manual, HNF-PRO-334, and meets the double contingency principle

  7. Building 773-A, Lab F003 Glovebox Project Radiological Design Summary Report

    International Nuclear Information System (INIS)

    Gaul, W.C.

    2003-01-01

    Engineering Standards present the radiological design criteria and requirements, which must be satisfied for all SRS facility designs. The radiological design criteria and requirements specified in the standard are based on the Code of Federal Regulations, DOE Orders, Site manuals, other applicable standards, and various DOE guides and handbooks. This report contains top-level requirements for the various areas of radiological protection for workers. For the purposes of demonstrating compliance with these requirements, the designer must examine the requirement for the design and either incorporate or provide a technical justification as to why the requirement is not incorporated. This document reports a radiological design review for the STREAK lab glovebox upgrades of inlet ventilation, additional mechanical and electrical services, new glovebox instrumentation and alarms. This report demonstrates that the gloveboxes meet the radiological design requirements of Engineering Standards

  8. Inductively coupled plasma-atomic emission spectroscopy glovebox assembly system at the West Valley Demonstration Project

    International Nuclear Information System (INIS)

    Marlow, J.H.; McCarthy, K.M.; Tamul, N.R.

    1999-01-01

    The inductively coupled plasma/atomic emission spectroscopy [ICP/AES (ICP)] system for elemental analyses in support of vitrification processing was first installed in 1986. The initial instrument was a Jobin Yvon (JY) Model JY-70 ICP that consisted of sequential and simultaneous spectrometers for analysis of nonradioactive samples as radioactive surrogates. The JY-70 ICP continued supporting nonradioactive testing during the Functional and Checkout Testing of Systems (FACTS) using the full-scale melter with ''cold'' (nonradioactive) testing campaigns. As a result, the need for another system was identified to allow for the analysis of radioactive samples. The Mass Spec (Spectrometry) Lab was established for the installation of the modified ICP system for handling radioactive samples. The conceptual setup of another ICP was predicated on the use of a hood to allow ease of accessibility of the torch, nebulizer, and spray chamber, and the minimization of air flow paths. However, reconsideration of the radioactive sample dose rate and contamination levels led to the configuration of the glovebox system with a common transfer interface box for the ICP and the inductively coupled plasma-mass spectrometer (ICP-MS) glovebox assemblies. As a result, a simultaneous Model JY-50P ICP with glovebox was installed in 1990 as a first generation ICP glovebox system. This was one of the first ICP glovebox assemblies connected with an ICP-MS glovebox system. Since the economics of processing high-level radioactive waste (HLW) required the availability of an instrument to operate 24 hours a day throughout the year without any downtime, a second generation ICP glovebox assembly was designed, manufactured, and installed in 1995 using a Model JY-46P ICP. These two ICP glovebox systems continue to support vitrification of the HLW into canisters for storage. The ICP systems have been instrumental in monitoring vitrification batch processing. To date, remote sample preparation and

  9. Alternative approach for fire suppression of class A, B and C fires in gloveboxes

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberger, Mark S [Los Alamos National Laboratory; Tsiagkouris, James A [Los Alamos National Laboratory

    2011-02-10

    Department of Energy (DOE) Orders and National Fire Protection Association (NFPA) Codes and Standards require fire suppression in gloveboxes. Several potential solutions have been and are currently being considered at Los Alamos National Laboratory (LANL). The objective is to provide reliable, minimally invasive, and seismically robust fire suppression capable of extinguishing Class A, B, and C fires; achieve compliance with DOE and NFPA requirements; and provide value-added improvements to fire safety in gloveboxes. This report provides a brief summary of current approaches and also documents the successful fire tests conducted to prove that one approach, specifically Fire Foe{trademark} tubes, is capable of achieving the requirement to provide reliable fire protection in gloveboxes in a cost-effective manner.

  10. Modular glovebox connector and associated good practices for control of radioactive and chemically toxic materials

    International Nuclear Information System (INIS)

    Hoover, M.D.; Mewhinney, C.J.; Newton, G.J.

    1999-01-01

    Design and associated good practices are described for a modular glovebox connector to improve control of radioactive and chemically toxic materials. The connector consists of an anodized aluminum circular port with a mating spacer, gaskets, and retaining rings for joining two parallel ends of commercially available or custom-manufactured glovebox enclosures. Use of the connector allows multiple gloveboxes to be quickly assembled or reconfigured in functional units. Connector dimensions can be scaled to meet operational requirements for access between gloveboxes. Options for construction materials are discussed, along with recommendations for installation of the connector in new or retrofitted systems. Associated good practices include application of surface coatings and caulking, use of disposable glovebags, and proper selection and protection of gasket and glove materials. Use of the connector at an inhalation toxicology research facility has reduced the time and expense required to reconfigure equipment for changing operational requirements, the dispersion of contamination during reconfigurations, and the need for decommissioning and disposal of contaminated enclosures

  11. HOLDUP MEASUREMENTS FOR VISUAL EXAMINATION GLOVEBOXES AT THE SAVANNAH RIVER SITE

    Energy Technology Data Exchange (ETDEWEB)

    Sigg, R

    2006-05-03

    Visual Examination (VE) gloveboxes are used at the Savannah River Site (SRS) to remediate transuranic waste (TRU) drums. Noncompliant items are removed before the drums undergo further characterization in preparation for shipment to the Waste Isolation Pilot Plant (WIPP). Maintaining the flow of drums through the remediation process is critical to the program's seven-days-per-week operation. Conservative assumptions are used to ensure that glovebox contamination from this continual operation is below acceptable limits. Holdup measurements are performed in order to confirm that these assumptions are conservative. High Cs-137 backgrounds in the VE glovebox areas preclude the use of a sodium iodide spectrometer, so a high-purity germanium (HPGe) detector, having superior resolution, is used. Plutonium-239 is usually the nuclide of interest; however, Pu-241, Np-237 (including its daughter Pa-233) and Pu-238 (if detected) are typically assayed. Cs-137 and Co-60 may also be detected but are not reported since they do not contribute to the Pu-239 Fissile Gram Equivalent or Pu-239 Equivalent Curies. HEPA filters, drums and waste boxes are also assayed by the same methodology. If--for example--the HEPA is contained in a stainless steel housing, attenuation corrections must be applied for both the filter and the housing. Dimensions, detector locations, materials and densities are provided as inputs to Ortec's ISOTOPIC software to estimate attenuation and geometry corrections for the measurement positions. This paper discusses the methodology, results and limitations of these measurements for different VE glovebox configurations.

  12. Inert atmosphere system for plutonium processing gloveboxes

    International Nuclear Information System (INIS)

    Bogard, C.F.; Calkins, K.W.; Rogers, R.F.

    1975-01-01

    Recent efforts to reduce fire hazards in plutonium processing operations are described. In such operations, the major environmental controls are developed through various kinds of glovebox systems. In evaluating the air-atmosphere glovebox systems, formerly in use at Rocky Flats and many other plants, a decision was made to convert to a recirculating ''inert'' atmosphere. The inert atmosphere consists of nitrogen, supplied from an on-site generating plant, diluting oxygen content to one to 5 percent by volume. Problems encountered during the change over included: determination of all factors influencing air leakage into the system, and reducing leakage to the practical minimum; meeting all fire and safety standards on the filter plenum and exhaust systems; provision for converting portions of the system to an air atmosphere to conduct maintenance work; inclusion of oxygen analyzers throughout the system to check gas quality and monitor for leaks; and the use of automatic controls to protect against a variety of potential malfunctions. The current objectives to reduce fire hazards have been met and additional safeguards were added. The systems are operating satisfactorily. (U.S.)

  13. Hands-on glovebox decommissioning

    International Nuclear Information System (INIS)

    Smith, D.

    1997-01-01

    Over recent years, the United Kingdom Atomic Energy Authority (UKAEA) has undertaken the decommissioning of a large number of Plutonium glove boxes at Winfrith Technology Centre. UKAEA has managed this work on behalf of the DTI, who funded most of the work. Most of the planning and practical work was contracted to AEA Technology (AEAT), which, until 1996, was the commercial arm of UKAEA, but is now a private company. More than 70 gloveboxes, together with internal plant and equipment such as ball mills, presses and furnaces, have been successfully size reduced into drums for storage, leaving the area, in which they were situated, in a clean condition. (UK)

  14. Improving Efficiency with 3-D Imaging: Technology Essential in Removing Plutonium Processing Equipment from Plutonium Finishing Plant Gloveboxes

    International Nuclear Information System (INIS)

    Crow, Stephen H.; Kyle, Richard N.; Minette, Michael J.

    2008-01-01

    The Plutonium Finishing Plant at Hanford, Washington began operations in 1949 to process plutonium and plutonium products. Its primary mission was to produce plutonium metal, fabricate weapons parts, and stabilize reactive materials. These operations, and subsequent activities, were performed in remote production lines, consisting primarily of hundreds of gloveboxes. Over the years these gloveboxes and processes have been continuously modified. The plant is currently inactive and Fluor Hanford has been tasked to clean out contaminated equipment and gloveboxes from the facility so it can be demolished in the near future. Approximately 100 gloveboxes at PFP have been cleaned out in the past four years and about 90 gloveboxes remain to be cleaned out. Because specific commitment dates for this work have been established with the State of Washington and other entities, it is important to adopt work practices that increase the safety and speed of this effort. The most recent work practice to be adopted by Fluor Hanford D and D workers is the use of 3-D models to improve the efficiency of cleaning out radioactive gloveboxes at the plant. The use of 3-D models has significantly improved the work planning process by providing workers with a clear image of glovebox construction and composition, which is then used to determine cleanout methods and work sequences. The 3-D visual products enhance safety by enabling workers to more easily identify hazards and implement controls. In addition, the ability to identify and target the removal of radiological materials early in the D and D process provides substantial dose reduction for the workers

  15. A human factors approach towards the design of a new glovebox glove for Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Oka, Jude M. [Los Alamos National Laboratory

    2012-08-06

    Present day glovebox gloves at Los Alamos National Laboratory (LANL) are underdeveloped and ergonomically inaccurate. This problem results in numerous sprain and strain injuries every year for employees who perform glovebox work. In addition to injuries, using the current glovebox glove design also contributes to breaches and contamination. The current glove used today at LANL has several problems: (1) The length of the fingers is incorrect, (2) the web spacing between the fingers is nonexistent, (3) the angles between each digit on the finger are incorrect, (4) the thumb is placed inaccurately, and (5) the length of the hand is incorrect. These problems present a need to correct the current glove design to decrease the risk of injuries, breaches, and contamination. Anthropometrics were researched to help find the best range of hand measurements to fix the current glove design. Anthropometrics is the measure of the human physical variation. Anthropometrics for this study were gathered from the American National Survey (ANSUR) data that was conducted by the U.S Army in 1988. The current glovebox glove uses anthropometrics from the 95th to 105th percentile range which is too large so the new gloves are going to implement data from a smaller range of percentile groups. The 105th percentile range represents measurements that exceed the human population but are needed to fit certain circumstance such as wearing several under gloves within the glovebox gloves. Anthropometrics used in this study include: 105th percentile measurements for joint circumference which was unchanged because the room for under gloves plus ease of hand insertion and extraction is needed, 80th percentile measurements for crotch length to allow workers to reach the web spacing in the glove, 20th percentile measurements for finger length to allow workers to reach the end of the glove, standard 10.5cm hand breadth to allow more room to accommodate under gloves, 45 degrees abduction angle for the

  16. W-026, transuranic waste restricted waste management (TRU RWM) glovebox operational test report

    Energy Technology Data Exchange (ETDEWEB)

    Leist, K.J.

    1998-02-18

    The TRU Waste/Restricted Waste Management (LLW/PWNP) Glovebox 401 is designed to accept and process waste from the Transuranic Process Glovebox 302. Waste is transferred to the glovebox via the Drath and Schraeder Bagless Transfer Port (DO-07401) on a transfer stand. The stand is removed with a hoist and the operator inspects the waste (with the aid of the Sampling and Treatment Director) to determine a course of action for each item. The waste is separated into compliant and non compliant. One Trip Port DO-07402A is designated as ``Compliant``and One Trip Port DO-07402B is designated as ``Non Compliant``. As the processing (inspection, bar coding, sampling and treatment) of the transferred items takes place, residue is placed in the appropriate One Trip port. The status of the waste items is tracked by the Data Management System (DMS) via the Plant Control System (PCS) barcode interface. As an item is moved for sampling or storage or it`s state altered by treatment, the Operator will track an items location using a portable barcode reader and entry any required data on the DMS console. The Operational Test Procedure (OTP) will perform evolutions (described here) using the Plant Operating Procedures (POP) in order to verify that they are sufficient and accurate for controlled glovebox operation.

  17. W-026, transuranic waste restricted waste management (TRU RWM) glovebox operational test report

    International Nuclear Information System (INIS)

    Leist, K.J.

    1998-01-01

    The TRU Waste/Restricted Waste Management (LLW/PWNP) Glovebox 401 is designed to accept and process waste from the Transuranic Process Glovebox 302. Waste is transferred to the glovebox via the Drath and Schraeder Bagless Transfer Port (DO-07401) on a transfer stand. The stand is removed with a hoist and the operator inspects the waste (with the aid of the Sampling and Treatment Director) to determine a course of action for each item. The waste is separated into compliant and non compliant. One Trip Port DO-07402A is designated as ''Compliant''and One Trip Port DO-07402B is designated as ''Non Compliant''. As the processing (inspection, bar coding, sampling and treatment) of the transferred items takes place, residue is placed in the appropriate One Trip port. The status of the waste items is tracked by the Data Management System (DMS) via the Plant Control System (PCS) barcode interface. As an item is moved for sampling or storage or it's state altered by treatment, the Operator will track an items location using a portable barcode reader and entry any required data on the DMS console. The Operational Test Procedure (OTP) will perform evolutions (described here) using the Plant Operating Procedures (POP) in order to verify that they are sufficient and accurate for controlled glovebox operation

  18. WRAP low level waste restricted waste management (LLW RWM) glovebox acceptance test report

    International Nuclear Information System (INIS)

    Leist, K.J.

    1997-01-01

    On April 22, 1997, the Low Level Waste Restricted Waste Management (LLW RWM) glovebox was tested using acceptance test procedure 13027A-87. Mr. Robert L. Warmenhoven served as test director, Mr. Kendrick Leist acted as test operator and test witness, and Michael Lane provided miscellaneous software support. The primary focus of the glovebox acceptance test was to examine glovebox control system interlocks, operator Interface Unit (OIU) menus, alarms, and messages. Basic drum port and lift table control sequences were demonstrated. OIU menus, messages, and alarm sequences were examined, with few exceptions noted. Barcode testing was bypassed, due to the lack of installed equipment as well as the switch from basic reliance on fixed bar code readers to the enhanced use of portable bar code readers. Bar code testing was completed during performance of the LLW RWM OTP. Mechanical and control deficiencies were documented as Test Exceptions during performance of this Acceptance Test. These items are attached as Appendix A to this report

  19. Adaptation of a glow discharge mass spectrometer in a glove-box for the analysis of nuclear materials

    International Nuclear Information System (INIS)

    Betti, M.; Rasmussen, G.; Hiernaut, T.; Koch, L.

    1994-01-01

    A VG9000 glow discharge mass spectrometer has been modified for the direct analysis of solid nuclear samples within a glove-box environment. Because containment is needed for the analysis of this kind of material, the glove-box encloses all parts of the instrument that come into contact with the sample, namely the ion source chamber, sample interlock and associated pumping system. External modifications eliminate outside contamination by the fitting of absolute filters on all source supplies. Internally the design of the ion source has been altered to minimize the number of operations performed inside the glove-box thereby simplifying operation and routine maintenance. These modifications retain the ion extraction and focusing properties of the instrument. The data presented show that there is no compromise in the analytical performance of the instrument when placed in the glove-box. Data representative of nuclear materials is also shown. (Author)

  20. A technique for the assessment of the masses of residual plutonium in gloveboxes using thermoluminescent dosimeters

    International Nuclear Information System (INIS)

    Day, B.; Godward, D.F.

    1979-01-01

    A means of measuring the mass of residual plutonium in gloveboxes in the size range 1 to 10 m 3 has been developed using multiple thermoluminescent detectors. By optimising the location and the number of detectors, and by using suitable filtration, the mean response from them has been made insensitive to the distribution and the composition of the plutonium. It is possible to detect 10 g of plutonium in the largest glovebox considered. The measurement and mass estimation processes have been reduced to simple operations which can be carried out by skilled industrial staff. The routine application of the technique has been arranged to minimise disturbance to be production work going on in the gloveboxes by making unattended measurements during silent hours

  1. Determination of an Ergonomically Sound Glovebox Glove Port Center Line

    Energy Technology Data Exchange (ETDEWEB)

    Christman, Marissa St John [Los Alamos National Laboratory

    2016-11-30

    Determine an ergonomic glovebox glove port center line location which will be used for standardization in new designs, thus allowing for predictable human work performance, reduced worker exposure to radiation and musculoskeletal injury risks, and improved worker comfort, efficiency, health, and safety.

  2. Determination of an Ergonomically Sound Glovebox Glove Port Center Line

    International Nuclear Information System (INIS)

    Christman, Marissa St; Land, Whitney Morgan

    2016-01-01

    Determine an ergonomic glovebox glove port center line location which will be used for standardization in new designs, thus allowing for predictable human work performance, reduced worker exposure to radiation and musculoskeletal injury risks, and improved worker comfort, efficiency, health, and safety.

  3. Preliminary evaluation of the electrapette for possible use in the glovebox for pipetting plutonium solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hansbury, E.; Ortiz, B.; Roybal, C.

    1990-12-01

    At the Los Alamos Laboratory Plutonium Facility, Solution Assay Instruments (SAIs) are used to provide real-time information on the plutonium (Pu) content of the process stream at various stages in the process. Much of the solution analysis must be carried and as a glovebox to protect the operator from radiation. In order to overcome some of the difficulties usually encountered when working in a glovebox, an electronic solution-volume measuring device called an Electrapette was ordered from Matrix Technologies Corporation. It is said to be highly accurate, simple to use, and can handle the 25 ml of solution required for SAI analyses. It is microprocessor-controlled and comes in two components connected by a detachable cable so that the electronic part can be installed outside the box, while the nosepiece is inside. The two pieces are connected through a plug-in on the glovebox wall. The Electrapette was tested in three sets of experiments: a cold'' lab set, a set run is a hood in a production building, and a third set run in a glovebox using a process solution whose density had been predetermined. The accuracy of the determination could not be determined because the samples had been mixed with other feed before being sent for analysis by the Electrapette. 2 refs., 5 tabs.

  4. Los Angeles International Airport Runway Incursion Studies: Phase III--Center-Taxiway Simulation

    Science.gov (United States)

    Madson, Michael D.

    2004-01-01

    Phase III of the Los Angeles International Airport Runway Incursion Studies was conducted, under an agreement with HNTB Corporation, at the NASA Ames FutureFlight Central (FFC) facility in June 2003. The objective of the study was the evaluation of a new center-taxiway concept at LAX. This study is an extension of the Phase I and Phase II studies previously conducted at FFC. This report presents results from Phase III of the study, in which a center-taxiway concept between runways 25L and 25R was simulated and evaluated. Phase III data were compared objectively against the Baseline data. Subjective evaluations by participating LAX controllers were obtained with regard to workload, efficiency, and safety criteria. To facilitate a valid comparison between Baseline and Phase III data, the same scenarios were used for Phase III that were tested during Phases I and II. This required briefing participating controllers on differences in airport and airline operations between 2001 and today.

  5. Decontamination and decommissioning of 61 plutonium gloveboxes in D-Wing, Building 212 Argonne National Laboratory-East: Final project report

    International Nuclear Information System (INIS)

    Cheever, C.L.; Rose, R.W.

    1996-09-01

    Argonne National Laboratory-East (ANL-E) is a government-owned, contractor operated, multipurpose research facility located 25 miles southwest of downtown Chicago on 689 hectares (1,700 acres) in DuPage County, Illinois, as shown in Figure 1.1. Building 212 is located in the central area of ANL-E, as shown in Figure 1.2. The purpose of this project was to eliminate the risk of radioactive material release from the contaminated glovebox systems and to make the laboratories available for unrestricted use. The following work objectives were established: (1) Identify and remove radioactive materials for return to ANL-E Special Materials control. (2) Remove and package the radioactively contaminated materials and equipment from the gloveboxes. (3) Decontaminate the gloveboxes to nontransuranic (non-TRU) levels. (4) Size-reduce and package the gloveboxes and support systems. (5) Document and dispose of the radioactive and mixed waste. (6) Decontaminate, survey, and release the nine laboratories and corridor areas for unrestricted use

  6. Objectives and methodology of BIOBADASER phase iii.

    Science.gov (United States)

    Sanchez-Piedra, Carlos; Hernández Miguel, M Victoria; Manero, Javier; Roselló, Rosa; Sánchez-Costa, Jesús Tomás; Rodríguez-Lozano, Carlos; Campos, Cristina; Cuende, Eduardo; Fernández-Lopez, Jesús Carlos; Bustabad, Sagrario; Martín Domenech, Raquel; Pérez-Pampín, Eva; Del Pino-Montes, Javier; Millan-Arcineas, Ana Milena; Díaz-González, Federico; Gómez-Reino, Juan Jesús

    2017-09-18

    Describe the objectives, methods and results of the first year of the new version of the Spanish registry of adverse events involving biological therapies and synthetic drugs with an identifiable target in rheumatic diseases (BIOBADASER III). Multicenter prospective registry of patients with rheumatic inflammatory diseases being treated with biological drugs or synthetic drugs with an identifiable target in rheumatology departments in Spain. The main objective of BIOBADASER Phase III is the registry and analysis of adverse events; moreover, a secondary objective was added consisting of assessing the effectiveness by means of the registry of activity indexes. Patients in the registry are evaluated at least once every year and whenever they experience an adverse event or a change in treatment. The collection of data for phase iii began on 17 December 2015. During the first year, 35 centers participated. The number of patients included in this new phase in December 2016 was 2,664. The mean age was 53.7 years and the median duration of treatment was 8.1 years. In all, 40.4% of the patients were diagnosed with rheumatoid arthritis. The most frequent adverse events were infections and infestations. BIOBADASER Phase III has been launched to adapt to a changing pharmacological environment, with the introduction of biosimilars and small molecules in the treatment of rheumatic diseases. This new stage is adapted to the changes in the reporting of adverse events and now includes information related to activity scores. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Reumatología y Colegio Mexicano de Reumatología. All rights reserved.

  7. Two-phase titration of cerium(III) by permanganate

    International Nuclear Information System (INIS)

    Lazarev, A.I.; Lazareva, V.I.; Gerko, V.V.

    1987-01-01

    This paper presents a method for the two-phase titrimetric determination of cerium(III) with permanganate which does not require an expenditure of sugar and preliminary removal of chlorides and nitrates. The interaction of cerium(III) with permanganate at room temperature was studied as a function of the pH, the concentration of pyrophosphate, tetraphenylphosphonium (TPP), permanganate, and extraneous compounds, the rate of titration, and the time of stay of the solution in air before titration. The investigations were conducted according to the following methodology: water, solution of cerium(III) pyrophosphate, and TPP were introduced into an Erlenmeyer flask with a side branch near the bottom for clearer observation of the color of the chloroform phase. The authors established the given pH value, poured the water into a volume of 50 ml, and added chloroform. The result was titrated with permanganate solutions of various concentrations until a violet color appeared in the chloroform phase

  8. Microgravity Science Glovebox Aboard the International Space Station

    Science.gov (United States)

    2003-01-01

    In the Destiny laboratory aboard the International Space Station (ISS), European Space Agency (ESA) astronaut Pedro Duque of Spain is seen working at the Microgravity Science Glovebox (MSG). He is working with the PROMISS experiment, which will investigate the growth processes of proteins during weightless conditions. The PROMISS is one of the Cervantes program of tests (consisting of 20 commercial experiments). The MSG is managed by NASA's Marshall Space Flight Center (MSFC).

  9. CSER 00-003: Criticality Safety Evaluation report for PFP Magnesium Hydroxide Precipitation Process for Plutonium Stabilization Glovebox 3

    International Nuclear Information System (INIS)

    LAN, J.S.

    2000-01-01

    This Criticality Safety Evaluation Report analyzes the stabilization of plutonium/uranium solutions in Glovebox 3 using the magnesium hydroxide precipitation process at PFP. The process covered are the receipt of diluted plutonium solutions into three precipitation tanks, the precipitation of plutonium from the solution, the filtering of the plutonium precipitate from the solution, the scraping of the precipitate from the filter into boats, and the initial drying of the precipitated slurry on a hot plate. A batch (up to 2.5 kg) is brought into the glovebox as plutonium nitrate, processed, and is then removed in boats for further processing. This CSER establishes limits for the magnesium hydroxide precipitation process in Glovebox 3 to maintain criticality safety while handling fissionable material

  10. Ultracold Field Gradient Magnetometry and Transport to Study Correlated Topological Phases

    Science.gov (United States)

    2016-10-01

    MIT) 77 Massachusetts Ave. NE18-901 Cambridge , MA 02139 -4307 ABSTRACT Number of Papers published in peer-reviewed journals: Number of Papers published...group of the PI and the subfield of new correlated topological phases. List of Illustrations Figure 1 – View of MBE and Glovebox System Figure... Illustrations   Figure 1 – View of MBE and Glovebox System  Figure 2 – View of Glovebox, MBE, and Dilution Refrigerator System    Statement of Problems Studied  To

  11. Low impact plutonium glovebox D&D

    Energy Technology Data Exchange (ETDEWEB)

    Rose, R.W.

    1995-12-31

    A dilemma often encountered in decontamination and decommissioning operations is the lack of choice as to the location where the work is to be performed. Facility siting, laboratory location, and adjacent support areas were often determined based on criteria, which while appropriate at the time, are not always the most conducive to a D&D project. One must learn to adapt and cope with as found conditions. High priority research activities, which cannot be interrupted, may be occurring in adjacent non-radiological facilities in the immediate vicinity where highly contaminated materials must be handled in the course of a D&D operation. The execution of a project within such an environment involves a high level of coordination, cooperation, professionalism and flexibility among the project, the work force and the surrounding occupants. Simply moving occupants from the potentially affected area is not always an option and much consideration must be given in the selection of the D&D methodology to be employed and the processes to be implemented. Determining project boundaries and the ensuring that adjacent occupants are included in the planning/scheduling of specific operations which impact their work area are important in the development of the safety envelope. Such was the case in the recent D&D of 61 gloveboxes contaminated with plutonium and other transuranic nuclides at the Argonne National Laboratory-East site. The gloveboxes, which were used in Department of Energy research and development program activities over the past 30 years, were decontaminated to below transuranic waste criteria, size reduced, packaged and removed from Building 212 by Argonne National Laboratory personnel in conjunction with Nuclear Fuel Services, Inc. with essentially no impact to adjacent occupants.

  12. Light transmission and air used for inspection of glovebox gloves

    International Nuclear Information System (INIS)

    Castro, Julio M.; Steckle, Warren P. Jr.; Macdonald, John M.

    2002-01-01

    Various materials used for manufacturing the glovebox gloves are translucent material such as hypalon, rubbers, and neoprene. This means that visible light can be transmitted through the inside of the material. Performing this test can help to increase visualization of the integrity of the glove. Certain flaws such as pockmarks, foreign material, pinholes, and scratches could be detected with increased accuracy. An analysis was conducted of the glovebox gloves obscure polymer material using a inspection light table. The fixture is equipped with a central light supply and small air pump to inflate the glove and test for leak and stability. A glove is affixed to the fixture for 360-degree inspection. Certain inspection processes can be performed: (1) Inspection for pockmarks and thin areas within the gloves; (2) Observation of foreign material within the polymer matrix; and (3) Measurements could be taken for gloves thickness using light measurements. This process could help reduce eyestrain when examining gloves and making a judgment call on the size of material thickness in some critical areas. Critical areas are fingertips and crotch of fingers.

  13. Probability of success for phase III after exploratory biomarker analysis in phase II.

    Science.gov (United States)

    Götte, Heiko; Kirchner, Marietta; Sailer, Martin Oliver

    2017-05-01

    The probability of success or average power describes the potential of a future trial by weighting the power with a probability distribution of the treatment effect. The treatment effect estimate from a previous trial can be used to define such a distribution. During the development of targeted therapies, it is common practice to look for predictive biomarkers. The consequence is that the trial population for phase III is often selected on the basis of the most extreme result from phase II biomarker subgroup analyses. In such a case, there is a tendency to overestimate the treatment effect. We investigate whether the overestimation of the treatment effect estimate from phase II is transformed into a positive bias for the probability of success for phase III. We simulate a phase II/III development program for targeted therapies. This simulation allows to investigate selection probabilities and allows to compare the estimated with the true probability of success. We consider the estimated probability of success with and without subgroup selection. Depending on the true treatment effects, there is a negative bias without selection because of the weighting by the phase II distribution. In comparison, selection increases the estimated probability of success. Thus, selection does not lead to a bias in probability of success if underestimation due to the phase II distribution and overestimation due to selection cancel each other out. We recommend to perform similar simulations in practice to get the necessary information about the risk and chances associated with such subgroup selection designs. Copyright © 2017 John Wiley & Sons, Ltd.

  14. Sample exchange/evaluation (SEE) report - Phase III

    International Nuclear Information System (INIS)

    Winters, W.I.

    1996-01-01

    This report describes the results from Phase III of the Sample Exchange Evaluation (SEE) program. The SEE program is used to compare analytical laboratory performance on samples from the Hanford Site's high level waste tanks

  15. Joint probability of statistical success of multiple phase III trials.

    Science.gov (United States)

    Zhang, Jianliang; Zhang, Jenny J

    2013-01-01

    In drug development, after completion of phase II proof-of-concept trials, the sponsor needs to make a go/no-go decision to start expensive phase III trials. The probability of statistical success (PoSS) of the phase III trials based on data from earlier studies is an important factor in that decision-making process. Instead of statistical power, the predictive power of a phase III trial, which takes into account the uncertainty in the estimation of treatment effect from earlier studies, has been proposed to evaluate the PoSS of a single trial. However, regulatory authorities generally require statistical significance in two (or more) trials for marketing licensure. We show that the predictive statistics of two future trials are statistically correlated through use of the common observed data from earlier studies. Thus, the joint predictive power should not be evaluated as a simplistic product of the predictive powers of the individual trials. We develop the relevant formulae for the appropriate evaluation of the joint predictive power and provide numerical examples. Our methodology is further extended to the more complex phase III development scenario comprising more than two (K > 2) trials, that is, the evaluation of the PoSS of at least k₀ (k₀≤ K) trials from a program of K total trials. Copyright © 2013 John Wiley & Sons, Ltd.

  16. Report of working group for technical standard of cutting and melting works in Glovebox dismantling

    International Nuclear Information System (INIS)

    Asazuma, Shinichiroh; Takeda, Shinsoh; Tajima, Shoichi

    2004-11-01

    In order to prevent spread of contamination, glovebox dismantling activity is usually performed in a confined enclosure with personal radioactive protective equipment. Since large potion of these materials is made of vinyl acetate, there exist potential risks of fire, damage and injury to the environment and workers during the dismantling (cutting or melting) operation. It is therefore important to establish standard for proper use of equipment and hazard controls in such a specific environment. Working Group composed of Tokai Works and Oarai Works has examined and developed the operational standard for cutting work in glovebox dismantlement. The result is reflected to the Tokai Works Safety Operational Standard. (author)

  17. Glovebox pressure relief and check valve

    Energy Technology Data Exchange (ETDEWEB)

    Blaedel, K.L.

    1986-03-17

    This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury.

  18. Glovebox pressure relief and check valve

    International Nuclear Information System (INIS)

    Blaedel, K.L.

    1986-01-01

    This device is a combined pressure relief valve and check valve providing overpressure protection and preventing back flow into an inert atmosphere enclosure. The pressure relief is embodied by a submerged vent line in a mercury reservior, the releif pressure being a function of the submerged depth. The pressure relief can be vented into an exhaust system and the relieving pressure is only slightly influenced by the varying pressure in the exhaust system. The check valve is embodied by a ball which floats on the mercury column and contacts a seat whenever vacuum exists within the glovebox enclosure. Alternatively, the check valve is embodied by a vertical column of mercury, the maximum back pressure being a function of the height of the column of mercury

  19. Unraveling aminophosphine redox mechanisms for glovebox-free InP quantum dot syntheses.

    Science.gov (United States)

    Laufersky, Geoffry; Bradley, Siobhan; Frécaut, Elian; Lein, Matthias; Nann, Thomas

    2018-05-10

    The synthesis of colloidal indium phosphide quantum dots (InP QDs) has always been plagued by difficulties arising from limited P3- sources. Being effectively restricted to the highly pyrophoric tris(trimethylsilyl) phosphine (TMS3P) creates complications for the average chemist and presents a significant risk for industrially scaled reactions. The adaptation of tris(dialkylamino) phosphines for these syntheses has garnered attention, as these new phosphines are much safer and can generate nanoparticles with competitive photoluminescence properties to those from (TMS)3P routes. Until now, the reaction mechanics of this precursor were elusive due to many experimental optimizations, such as the inclusion of a high concentration of zinc salts, being atypical of previous InP syntheses. Herein, we utilize density functional theory calculations to outline a logical reaction mechanism. The aminophosphine precursor is found to require activation by a zinc halide before undergoing a disproportionation reaction to self-reduce this P(iii) material to a P(-iii) source. We use this understanding to adapt this precursor for a two-pot nanoparticle synthesis in a noncoordinating solvent outside of glovebox conditions. This allowed us to generate spherical InP/ZnS nanoparticles possessing fluorescence quantum yields >55% and lifetimes as fast as 48 ns, with tunable emission according to varying zinc halide acidity. The development of high quality and efficient InP QDs with this safer aminophosphine in simple Schlenk environments will enable a broader range of researchers to synthesize these nontoxic materials for a variety of high-value applications.

  20. Procedure for hazards analysis of plutonium gloveboxes used in analytical chemistry operations

    International Nuclear Information System (INIS)

    Delvin, W.L.

    1977-06-01

    A procedure is presented to identify and assess hazards associated with gloveboxes used for analytical chemistry operations involving plutonium. This procedure is based upon analytic tree methodology and it has been adapted from the US Energy Research and Development Administration's safety program, the Management Oversight and Risk Tree

  1. 78 FR 73555 - Deepwater Horizon Oil Spill; Draft Programmatic and Phase III Early Restoration Plan and Draft...

    Science.gov (United States)

    2013-12-06

    ... Environmental Impact Statement (Draft Phase III ERP/PEIS). The Draft Phase III ERP/PEIS considers programmatic... programmatic restoration alternatives. The Draft Phase III ERP/PEIS evaluates these restoration alternatives... the Framework Agreement. The Draft Phase III ERP/PEIS also evaluates the environmental consequences of...

  2. Low impact plutonium glovebox D ampersand D

    International Nuclear Information System (INIS)

    Rose, R.W.

    1995-01-01

    A dilemma often encountered in decontamination and decommissioning operations is the lack of choice as to the location where the work is to be performed. Facility siting, laboratory location, and adjacent support areas were often determined based on criteria, which while appropriate at the time, are not always the most conducive to a D ampersand D project. One must learn to adapt and cope with as found conditions. High priority research activities, which cannot be interrupted, may be occurring in adjacent non-radiological facilities in the immediate vicinity where highly contaminated materials must be handled in the course of a D ampersand D operation. The execution of a project within such an environment involves a high level of coordination, cooperation, professionalism and flexibility among the project, the work force and the surrounding occupants. Simply moving occupants from the potentially affected area is not always an option and much consideration must be given in the selection of the D ampersand D methodology to be employed and the processes to be implemented. Determining project boundaries and the ensuring that adjacent occupants are included in the planning/scheduling of specific operations which impact their work area are important in the development of the safety envelope. Such was the case in the recent D ampersand D of 61 gloveboxes contaminated with plutonium and other transuranic nuclides at the Argonne National Laboratory-East site. The gloveboxes, which were used in Department of Energy research and development program activities over the past 30 years, were decontaminated to below transuranic waste criteria, size reduced, packaged and removed from Building 212 by Argonne National Laboratory personnel in conjunction with Nuclear Fuel Services, Inc. with essentially no impact to adjacent occupants

  3. Process and device for extinguishing fires inside gloveboxes

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, P

    1975-01-09

    The present invention relates to a process of extinguishing all types of fire inside gloveboxes. Said process prevents the inner part of the box to communicate with the room atmosphere: the glove that is the nearest to the hearth of fire is perforated with an edged tip mounted on the outlet of the extinguisher and the product contained inside said extinguisher is released until the fire extinction is achieved. A device for operating said process consists in an edged tubular tip, the end of which is bevelled and in means of dispersion and of connection to an extinguisher at the other end.

  4. Virtual Glovebox (VGX) Aids Astronauts in Pre-Flight Training

    Science.gov (United States)

    2003-01-01

    NASA's Virtual Glovebox (VGX) was developed to allow astronauts on Earth to train for complex biology research tasks in space. The astronauts may reach into the virtual environment, naturally manipulating specimens, tools, equipment, and accessories in a simulated microgravity environment as they would do in space. Such virtual reality technology also provides engineers and space operations staff with rapid prototyping, planning, and human performance modeling capabilities. Other Earth based applications being explored for this technology include biomedical procedural training and training for disarming bio-terrorism weapons.

  5. Automation of Command and Data Entry in a Glovebox Work Volume: An Evaluation of Data Entry Devices

    Science.gov (United States)

    Steele, Marianne K.; Nakamura, Gail; Havens, Cindy; LeMay, Moira

    1996-01-01

    The present study was designed to examine the human-computer interface for data entry while performing experimental procedures within a glovebox work volume in order to make a recommendation to the Space Station Biological Research Project for a data entry system to be used within the Life Sciences Glovebox. Test subjects entered data using either a manual keypad, similar to a standard computer numerical keypad located within the glovebox work volume, or a voice input system using a speech recognition program with a microphone headset. Numerical input and commands were programmed in an identical manner between the two systems. With both electronic systems, a small trackball was available within the work volume for cursor control. Data, such as sample vial identification numbers, sample tissue weights, and health check parameters of the specimen, were entered directly into procedures that were electronically displayed on a video monitor within the glovebox. A pen and paper system with a 'flip-chart' format for procedure display, similar to that currently in use on the Space Shuttle, was used as a baseline data entry condition. Procedures were performed by a single operator; eight test subjects were used in the study. The electronic systems were tested under both a 'nominal' or 'anomalous' condition. The anomalous condition was introduced into the experimental procedure to increase the probability of finding limitations or problems with human interactions with the electronic systems. Each subject performed five test runs during a test day: two procedures each with voice and keypad, one with and one without anomalies, and one pen and paper procedure. The data collected were both quantitative (times, errors) and qualitative (subjective ratings of the subjects).

  6. Solar neutrino oscillation parameters after SNO Phase-III and SAGE Part-III

    International Nuclear Information System (INIS)

    Yang Ping; Liu Qiuyu

    2009-01-01

    We analyse the recently published results from solar neutrino experiments SNO Phase-III and SAGE Part-III and show their constraints on solar neutrino oscillation parameters, especially for the mixing angle θ 12 . Through a global analysis using all existing data from SK, SNO, Ga and Cl radiochemical experiments and long base line reactor experiment KamLAND , we obtain the parameters Δm 12 2 =7.684 -0.208 +0.212 x 10 -5 eV 2 , tan 2 θ 12 =0.440 -0.057 +0.059 . We also find that the discrepancy between the KamLAND and solar neutrino results can be reduced by choosing a small non-zero value for the mixing angle θ 13 . (authors)

  7. NASA Virtual Glovebox: An Immersive Virtual Desktop Environment for Training Astronauts in Life Science Experiments

    Science.gov (United States)

    Twombly, I. Alexander; Smith, Jeffrey; Bruyns, Cynthia; Montgomery, Kevin; Boyle, Richard

    2003-01-01

    The International Space Station will soon provide an unparalleled research facility for studying the near- and longer-term effects of microgravity on living systems. Using the Space Station Glovebox Facility - a compact, fully contained reach-in environment - astronauts will conduct technically challenging life sciences experiments. Virtual environment technologies are being developed at NASA Ames Research Center to help realize the scientific potential of this unique resource by facilitating the experimental hardware and protocol designs and by assisting the astronauts in training. The Virtual GloveboX (VGX) integrates high-fidelity graphics, force-feedback devices and real- time computer simulation engines to achieve an immersive training environment. Here, we describe the prototype VGX system, the distributed processing architecture used in the simulation environment, and modifications to the visualization pipeline required to accommodate the display configuration.

  8. Operational considerations for the Space Station Life Science Glovebox

    Science.gov (United States)

    Rasmussen, Daryl N.; Bosley, John J.; Vogelsong, Kristofer; Schnepp, Tery A.; Phillips, Robert W.

    1988-01-01

    The U.S. Laboratory (USL) module on Space Station will house a biological research facility for multidisciplinary research using living plant and animal specimens. Environmentally closed chambers isolate the specimen habitats, but specimens must be removed from these chambers during research procedures as well as while the chambers are being cleaned. An enclosed, sealed Life Science Glovebox (LSG) is the only locale in the USL where specimens can be accessed by crew members. This paper discusses the key science, engineering and operational considerations and constraints involving the LSG, such as bioisolation, accessibility, and functional versatility.

  9. Phase III Simplified Integrated Test (SIT) results - Space Station ECLSS testing

    Science.gov (United States)

    Roberts, Barry C.; Carrasquillo, Robyn L.; Dubiel, Melissa Y.; Ogle, Kathryn Y.; Perry, Jay L.; Whitley, Ken M.

    1990-01-01

    During 1989, phase III testing of Space Station Freedom Environmental Control and Life Support Systems (ECLSS) began at Marshall Space Flight Center (MSFC) with the Simplified Integrated Test. This test, conducted at the MSFC Core Module Integration Facility (CMIF), was the first time the four baseline air revitalization subsystems were integrated together. This paper details the results and lessons learned from the phase III SIT. Future plans for testing at the MSFC CMIF are also discussed.

  10. Aqueous phase complexation of Cm(III) and Cf(III) with ionizable macrocyclic ligands

    International Nuclear Information System (INIS)

    Manchanda, V.K.; Mohapatra, P.K.

    1995-01-01

    Complexation behaviour of Cm(III) and Cf(III) with 1,7-diaza-4,10,13-trioxacyclopentadecane-N,N'-diacetic acid (K21DA), 1,10-diaza-4,7,13,16-tetraoxacyclooctadecane-N,N'-diacetic acid (K22DA) and ethylene diamine N,N'- diacetic acid (EDDA) has been investigated using dinonyl naphthalene sulphonic acid (DNNS), in tetramethyl ammonium form as liquid cation exchanger. The aqueous phase complex formation constants are computed from the distribution data. Though larger complex formation constants are observed with K21DA as well as K22DA compared to those with the acyclic analog EDDA, no size correlation is observed. (author). 5 refs., 1 tab

  11. Qinshan Phase III (CANDU) nuclear power project quality assurance

    International Nuclear Information System (INIS)

    Wang Lingen; Du Jinxiang

    2001-01-01

    The completion and implementation of quality assurance system of Qinshan Phase III (CANDU) nuclear power project are presented. Some comments and understanding with consideration of the project characteristics are put forward

  12. Effects of glovebox gloves on grip and key pinch strength and contact forces for simulated manual operations with three commonly used hand tools.

    Science.gov (United States)

    Sung, Peng-Cheng

    2014-01-01

    This study examined the effects of glovebox gloves for 11 females on maximum grip and key pinch strength and on contact forces generated from simulated tasks of a roller, a pair of tweezers and a crescent wrench. The independent variables were gloves fabricated of butyl, CSM/hypalon and neoprene materials; two glove thicknesses; and layers of gloves worn including single, double and triple gloving. CSM/hypalon and butyl gloves produced greater grip strength than the neoprene gloves. CSM/hypalon gloves also lowered contact forces for roller and wrench tasks. Single gloving and thin gloves improved hand strength performances. However, triple layers lowered contact forces for all tasks. Based on the evaluating results, selection and design recommendations of gloves for three hand tools were provided to minimise the effects on hand strength and optimise protection of the palmar hand in glovebox environments. To improve safety and health in the glovebox environments where gloves usage is a necessity, this study provides recommendations for selection and design of glovebox gloves for three hand tools including a roller, a pair of tweezers and a crescent wrench based on the results discovered in the experiments.

  13. Superconductivity in the unconventional high pressure phase bismuth-III

    Energy Technology Data Exchange (ETDEWEB)

    Semeniuk, Konstantin; Brown, Philip; Vasiljkovic, Aleksandar; Grosche, Malte [University of Cambridge (United Kingdom)

    2015-07-01

    One of the most surprising developments in high pressure research was the realisation that many elements assume very unexpected high pressure structures, described in terms of extremely large or even infinite unit cells. Elemental bismuth, which has been known to undergo a series of pressure induced structural transitions between 25 kbar and 80 kbar, is an interesting example: the intermediate pressure Bi-III phase has a complex 'host-guest' structure consisting of two incommensurate sublattices. Since the unit cell is infinitely large, the description of electronic and lattice excitations is problematic. Apart from its metallic character and the observation of superconductivity at low temperature, little is known about the electronic structure in this phase. We investigate the electrical resistivity within the metallic Bi-III phase under high hydrostatic pressure and in applied magnetic field using a piston cylinder cell. Superconductivity is observed below 7.1 K, and we extract the temperature dependence of the upper critical field, which exceeds 2 T at low temperature. The normal state resistivity exhibits an approximately linear temperature dependence. This could be attributed to strong scattering from low-lying excitations, as caused by an unusually soft phonon spectrum. The results suggest that strong coupling superconductivity arises within the host-guest structure of Bi-III out of an unusual electronic state.

  14. A new glove-box system for a high-pressure tritium pump

    International Nuclear Information System (INIS)

    Wilson, S.W.; Borree, R.J.; Chambers, D.I.; Chang, Y.; Merrill, J.T.; Souers, P.C.; Wiggins, R.K.

    1988-01-01

    A new glove-box system that was designed around a high-pressure tritium pump is described. The system incorporates new containment ideas such as ''burpler'' passive pressure controls, valves that can be turned from outside the box, inflatable door seals, ferro-fluidic motor-shaft seals, and rapid box-to-hood conversion during cryostaging. Currently under construction, the system will contain nine separate sections with automatic pressure-balancing and venting systems. 3 refs., 5 figs

  15. Palestinian Adolescents Coping with Trauma (PACT) - Phase III ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Palestinian Adolescents Coping with Trauma (PACT) - Phase III. Violent conflict has been repeatedly shown to result in severe, long-term social and mental health problems for exposed children and adolescents. While in the developed world, it is generally accepted that individuals seek professional one-on-one ...

  16. Object-oriented process dose modeling for glovebox operations

    International Nuclear Information System (INIS)

    Boerigter, S.T.; Fasel, J.H.; Kornreich, D.E.

    1999-01-01

    The Plutonium Facility at Los Alamos National Laboratory supports several defense and nondefense-related missions for the country by performing fabrication, surveillance, and research and development for materials and components that contain plutonium. Most operations occur in rooms with one or more arrays of gloveboxes connected to each other via trolley gloveboxes. Minimizing the effective dose equivalent (EDE) is a growing concern as a result of steadily declining allowable dose limits being imposed and a growing general awareness of safety in the workplace. In general, the authors discriminate three components of a worker's total EDE: the primary EDE, the secondary EDE, and background EDE. A particular background source of interest is the nuclear materials vault. The distinction between sources inside and outside of a particular room is arbitrary with the underlying assumption that building walls and floors provide significant shielding to justify including sources in other rooms in the background category. Los Alamos has developed the Process Modeling System (ProMoS) primarily for performing process analyses of nuclear operations. ProMoS is an object-oriented, discrete-event simulation package that has been used to analyze operations at Los Alamos and proposed facilities such as the new fabrication facilities for the Complex-21 effort. In the past, crude estimates of the process dose (the EDE received when a particular process occurred), room dose (the EDE received when a particular process occurred in a given room), and facility dose (the EDE received when a particular process occurred in the facility) were used to obtain an integrated EDE for a given process. Modifications to the ProMoS package were made to utilize secondary dose information to use dose modeling to enhance the process modeling efforts

  17. Dismantling of a furnace and gloveboxes of a U3O8 with 20% enrichment production line

    International Nuclear Information System (INIS)

    Yorio, Daniel; Cinat, Enrique; Cincotta, Daniel; Fernandez, Carlos A.; Bruno, Hernan R.; Camacho, Esteban F.; Boero, Norma

    1999-01-01

    In the Uranium Powder Manufacturing Plant at CAC, U 3 O 8 with 20% enrichment is manufactured for fuel plates to be used in test reactors. This plant is in full operation since 1986, producing uranium oxide for Peru, Algeria, Iran, Egypt and the RA-3-CAE reactors. Some of the equipment of the Plant have finished their life time and one of the furnaces of the processing line had to be replaced. This work implied the dismantling not only of the furnace, but also of the gloveboxes connected to the furnace and the dismantling of the extraction lines and air injection of the gloveboxes. The work had to be performed with the necessary care in order to minimize risks and effects on personnel, installations and environment involved. (author)

  18. CHAOS. III. GAS-PHASE ABUNDANCES IN NGC 5457

    Energy Technology Data Exchange (ETDEWEB)

    Croxall, Kevin V.; Pogge, Richard W. [Department of Astronomy, The Ohio State University, 140 West 18th Avenue, Columbus, OH 43210 (United States); Berg, Danielle A. [Center for Gravitation, Cosmology and Astrophysics, Department of Physics, University of Wisconsin Milwaukee, 1900 East Kenwood Boulevard, Milwaukee, WI 53211 (United States); Skillman, Evan D. [Minnesota Institute for Astrophysics, University of Minnesota, 116 Church Street SE, Minneapolis, MN 55455 (United States); Moustakas, John [Department of Physics and Astronomy, Siena College, 515 Loudon Road, Loudonville, NY 12211 (United States)

    2016-10-10

    We present Large Binocular Telescope observations of 109 H ii regions in NGC 5457 (M101) obtained with the Multi-Object Double Spectrograph. We have robust measurements of one or more temperature-sensitive auroral emission lines for 74 H ii regions, permitting the measurement of “direct” gas-phase abundances. Comparing the temperatures derived from the different ionic species, we find: (1) strong correlations of T [N ii] with T [S iii] and T [O iii], consistent with little or no intrinsic scatter; (2) a correlation of T [S iii] with T [O iii], but with significant intrinsic dispersion; (3) overall agreement between T [N ii], T [S ii], and T [O ii], as expected, but with significant outliers; (4) the correlations of T [N ii] with T [S iii] and T [O iii] match the predictions of photoionization modeling while the correlation of T [S iii] with T [O iii] is offset from the prediction of photoionization modeling. Based on these observations, which include significantly more observations of lower excitation H ii regions, missing in many analyses, we inspect the commonly used ionization correction factors (ICFs) for unobserved ionic species and propose new empirical ICFs for S and Ar. We have discovered an unexpected population of H ii regions with a significant offset to low values in Ne/O, which defies explanation. We derive radial gradients in O/H and N/O which agree with previous studies. Our large observational database allows us to examine the dispersion in abundances, and we find intrinsic dispersions of 0.074 ± 0.009 in O/H and 0.095 ± 0.009 in N/O (at a given radius). We stress that this measurement of the intrinsic dispersion comes exclusively from direct abundance measurements of H ii regions in NGC 5457.

  19. Equipping a glovebox for waste form testing and characterization of plutonium bearing materials

    International Nuclear Information System (INIS)

    Noy, M.; Johnson, S.G.; Moschetti, T.L.

    1997-01-01

    The recent decision by the Department of Energy to pursue a hybrid option for the disposition of weapons plutonium has created the need for additional facilities that can examine and characterize waste forms that contain Pu. This hybrid option consists of the placement of plutonium into stable waste forms and also into mixed oxide fuel for commercial reactors. Glass and glass-ceramic waste forms have a long history of being effective hosts for containing radionuclides, including plutonium. The types of tests necessary to characterize the performance of candidate waste forms include: static leaching experiments on both monolithic and crushed waste forms, microscopic examination, and density determination. Frequently, the respective candidate waste forms must first be produced using elevated temperatures and/or high pressures. The desired operations in the glovebox include, but are not limited to the following: (1) production of vitrified/sintered samples, (2) sampling of glass from crucibles or other vessels, (3) preparing samples for microscopic inspection and monolithic and crushed static leach tests, and (4) performing and analyzing leach tests in situ. This paper will describe the essential equipment and modifications that are necessary to successfully accomplish the goal of outfitting a glovebox for these functions

  20. Glovebox design requirements for molten salt oxidation processing of transuranic waste

    International Nuclear Information System (INIS)

    Ramsey, K.B.; Acosta, S.V.; Wernly, K.D.

    1998-01-01

    This paper presents an overview of potential technologies for stabilization of 238 Pu-contaminated combustible waste. Molten salt oxidation (MSO) provides a method for removing greater than 99.999% of the organic matrix from combustible waste. Implementation of MSO processing at the Los Alamos National Laboratory (LANL) Plutonium Facility will eliminate the combustible matrix from 238 Pu-contaminated waste and consequently reduce the cost of TRU waste disposal operations at LANL. The glovebox design requirements for unit operations including size reduction and MSO processing will be presented

  1. Individualized Inservice Teacher Education (Project In-Step). Evaluation Report. Phase III.

    Science.gov (United States)

    Thurber, John C.

    This is a report on the third phase of Project IN-STEP, which was intended to develop a viable model for individualized, multi-media in-service teacher education programs. (Phase I and II are reported in ED 033 905, and ED 042 709). The rationale for Phase III was to see if the model could be successfully transferred to an area other than teaching…

  2. The Virtual GloveboX (VGX: a Semi-immersive Virtual Environment for Training Astronauts in Life Sciences Experiments

    Directory of Open Access Journals (Sweden)

    I. Alexander Twombly

    2004-06-01

    Full Text Available The International Space Station will soon provide an unparalleled research facility for studying the near- and longer-term effects of microgravity on living systems. Using the Space Station Glovebox Facility - a compact, fully contained reach-in environment - astronauts will conduct technically challenging life sciences experiments. Virtual environment technologies are being developed at NASA Ames Research Center to help realize the scientific potential of this unique resource by facilitating the experimental hardware and protocol designs and by assisting the astronauts in training. The "Virtual GloveboX" (VGX integrates high-fidelity graphics, force-feedback devices and real-time computer simulation engines to achieve an immersive training environment. Here, we describe the prototype VGX system, the distributed processing architecture used in the simulation environment, and modifications to the visualization pipeline required to accommodate the display configuration.

  3. Unraveling the Mystery of the Blue Fog: Structure, Properties, and Applications of Amorphous Blue Phase III.

    Science.gov (United States)

    Gandhi, Sahil Sandesh; Chien, Liang-Chy

    2017-12-01

    The amorphous blue phase III of cholesteric liquid crystals, also known as the "blue fog," are among the rising stars in materials science that can potentially be used to develop next-generation displays with the ability to compete toe-to-toe with disruptive technologies like organic light-emitting diodes. The structure and properties of the practically unobservable blue phase III have eluded scientists for more than a century since it was discovered. This progress report reviews the developments in this field from both fundamental and applied research perspectives. The first part of this progress report gives an overview of the 130-years-long scientific tour-de-force that very recently resulted in the revelation of the mysterious structure of blue phase III. The second part reviews progress made in the past decade in developing electrooptical, optical, and photonic devices based on blue phase III. The strong and weak aspects of the development of these devices are underlined and criticized, respectively. The third- and-final part proposes ideas for further improvement in blue phase III technology to make it feasible for commercialization and widespread use. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Glovebox design requirements for molten salt oxidation processing of transuranic waste

    Energy Technology Data Exchange (ETDEWEB)

    Ramsey, K.B.; Acosta, S.V. [Los Alamos National Lab., NM (United States); Wernly, K.D. [Molten Salt Oxidation Corp., Bensalem, PA (United States)

    1998-12-31

    This paper presents an overview of potential technologies for stabilization of {sup 238}Pu-contaminated combustible waste. Molten salt oxidation (MSO) provides a method for removing greater than 99.999% of the organic matrix from combustible waste. Implementation of MSO processing at the Los Alamos National Laboratory (LANL) Plutonium Facility will eliminate the combustible matrix from {sup 238}Pu-contaminated waste and consequently reduce the cost of TRU waste disposal operations at LANL. The glovebox design requirements for unit operations including size reduction and MSO processing will be presented.

  5. Research ICT Africa (RIA!) - phase III | CRDI - Centre de recherches ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Research ICT Africa (RIA!) - phase III. Depuis la création du réseau RIA! en 2003, ses responsables ont mené avec succès des études portant tant sur l'offre que sur la demande afin de permettre de mieux comprendre l'accès aux TIC et leur utilisation en Afrique. Au cours des deux premières phases du projet (nos 101584 ...

  6. Public Policy and Protection from Exclusion - Phase III | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Public Policy and Protection from Exclusion - Phase III ... and decision-makers active in the promotion of equitable health policies, with a view to promoting the emergence of an observatory of health systems in the ... Policy in Focus publishes a special issue profiling evidence to empower women in the labour market.

  7. Design and fabrication of a glovebox for the Plasma Hearth Process radioactive bench-scale system

    International Nuclear Information System (INIS)

    Wahlquist, D.R.

    1996-01-01

    This paper presents some of the design considerations and fabrication techniques for building a glovebox for the Plasma Hearth Process (PHP) radioactive bench-scale system. The PHP radioactive bench-scale system uses a plasma torch to process a variety of radioactive materials into a final vitrified waste form. The processed waste will contain plutonium and trace amounts of other radioactive materials. The glovebox used in this system is located directly below the plasma chamber and is called the Hearth Handling Enclosure (HHE). The HHE is designed to maintain a confinement boundary between the processed waste and the operator. Operations that take place inside the HHE include raising and lowering the hearth using a hydraulic lift table, transporting the hearth within the HHE using an overhead monorail and hoist system, sampling and disassembly of the processed waste and hearth, weighing the hearth, rebuilding a hearth, and sampling HEPA filters. The PHP radioactive bench-scale system is located at the TREAT facility at Argonne National Laboratory-West in Idaho Falls, Idaho

  8. Brush Day & Night Phase III to Phase IV: ensuring that good oral health habits are sustainable.

    Science.gov (United States)

    Melo, Paulo; Fine, Charlotte; Malone, Sinead; Horn, Virginie

    2018-05-01

    Over the past 10 years, the FDI-Unilever Brush Day & Night partnership has significantly influenced the life of children worldwide through the implementation of school programmes for oral health education and prevention. This article reports the key facts and outcomes of Phase III of the partnership, and announces the launch of Phase IV. During Phase III, the expert advisors of the Brush Day & Night partnership conducted a longitudinal study to evaluate the impact of the '21 Day' programme in almost 8,000 children in 10 countries. Analysis revealed the effectiveness of the 21 Day programme in sustainably educating children to brush their teeth twice a day, with the greatest impact observed in children aged 7-9 years. With the launch of Phase IV, the Brush Day & Night partnership will continue to deliver its oral health school programme for 7-9 year-old children with a strengthened methodology, including randomized sampling and control groups. The scope of the evaluation will be broadened to include oral health-related quality of life indicators, and monitoring of the oral health knowledge of children's parents/carers. © 2018 FDI World Dental Federation.

  9. The coupling of thermochemistry and phase diagrams for group III-V semiconductor systems. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.J.

    1998-07-21

    The project was directed at linking the thermochemical properties of III-V compound semiconductors systems with the reported phase diagrams. The solid-liquid phase equilibrium problem was formulated and three approaches to calculating the reduced standard state chemical potential were identified and values were calculated. In addition, thermochemical values for critical properties were measured using solid state electrochemical techniques. These values, along with the standard state chemical potentials and other available thermochemical and phase diagram data, were combined with a critical assessment of selected III-V systems. This work was culminated with a comprehensive assessment of all the III-V binary systems. A novel aspect of the experimental part of this project was the demonstration of the use of a liquid encapsulate to measure component activities by a solid state emf technique in liquid III-V systems that exhibit high vapor pressures at the measurement temperature.

  10. Exploring the Photoreduction of Au(III) Complexes in the Gas-Phase

    Science.gov (United States)

    Marcum, Jesse C.; Kaufman, Sydney H.; Weber, J. Mathias

    2010-06-01

    We have used photodissociation spectroscopy to probe the electronic structure and photoreduction of Au(III) in gas-phase complexes containing Cl- and OH-. The gas-phase electronic spectrum of [AuCl_4]- closely resembles the aqueous solution spectrum, showing a lack of strong solvatochromic shifts. Substitution of Cl- ligands with OH- results in a strong blue shift, in agreement with ligand-field theory. Upon excitation, [AuCl_4]- can dissociate by loss of either one or two neutral Cl atoms, resulting in the reduction of gold from Au(III) to Au(II) and Au(I) respectively. The hydroxide substituted complex, [AuCl_2(OH)_2]-, demonstrates similar behavior but the only observable fragment channel is the loss of two neutral OH ligands, leading only to Au(I).

  11. MAQARIN natural analogue study: phase III

    International Nuclear Information System (INIS)

    Alexander, W.R.; Mazurek, M.; Waber, H.N.; Arlinger, J.; Erlandson, A.C.; Hallbeck, L.; Pedersen, K.; Chambers, A.V.; Haworth, A.; Ilett, D.; Linklater, C.M.; Tweed, C.J.; Chenery, S.R.N.; Kemp, S.J.; Milodowski, A.E.; Pearce, J.M.; Reeder, S.; Rochelle, C.A.; Smith, B.; Wetton, P.D.; Wragg, J.; Clark, I.D.; Karlsson, F.; Khoury, H.N.; Salameh, E.; Lagerblad, B.; Longworth, G.; Savage, D.; Smellie, J.A.T.

    1998-12-01

    This report represents the conclusion to Phase III of the Maqarin Natural Analogue Study. The main thrust was to establish the origin and chemistry of the Western Springs hyper alkaline groundwaters (Na/K enriched Ca(OH) 2 type) and to study their interaction with rocks of different compositions, as natural analogues to key processes that might occur at an early stage within the 'alkali disturbed zone' of cementitious repositories in different host rocks. Whilst earlier studies at Maqarin were very much site-specific and process-oriented, Phase III provided a regional perspective to the geological evolution of the Maqarin region. This was made possible by greater field access which allowed a more systematic structural and geomorphological study of the area. This has resulted in a greater understanding of the age and spatial relationships concerning formation of the cement zones through spontaneous combustion of the Bituminous Marls, and the subsequent formation of high pH groundwaters at the Eastern and Western Springs locations. At the Western Springs locality, hydrochemical and hydrogeological evaluation of new and published data (plus access to unpublished data), together with detailed mineralogical and geochemical studies, helped to clarify the very earliest stage of cement leachate/host rock interaction. The data were used also to test coupled flow/transport codes developed to assess the long-term evolution of a cementitious repository. Additional objectives addressed include: a) rock matrix diffusion, b) the occurrence and chemical controls on zeolite composition, e) the occurrence and chemical controls on clay stability, and d) the role of microbes, organics and colloids in trace element transport. The Maqarin site now provides a consistent picture explaining the origin of the hyperalkaline groundwaters, and is therefore a unique location for the examination of the mechanisms and processes associated with cementitious repositories. Application of these

  12. On the determination of Zr(IV), Ce((III), Th(IV) and U(VI) in organic phase using arsenazo-I and arsenazo-III

    International Nuclear Information System (INIS)

    El-Sweify, F.H.; Kamel, M.M.; Shabana, R.

    1997-01-01

    Some organic extractants of different types, namely tridodecylamine (TDA), tricapryl methyl ammonium chloride (TCMA), di(2-ethylhexyl) phosphoric acid (HDEHP) and 1-[thenoyl-(2)]-3,3,3-trifluoroacetone (HTTA) in xylene have been used to study the extraction behaviour of coloured complexes of Zr(IV), Ce(III), Th(IV) and U(VI) from slightly acidic aqueous solutions of arsenazo-III. Spectrophotometric study for the determination of the aforementioned elements, as well as the colouring agents arsenazo-I and arsenazo-III in the organic phase has been carried out. Some factors affecting the spectrophotometric determination of these elements were studied. These factors were hydrogen ion concentration, concentration of the colouring agents in the aqueous phase and diluent type. Absorption spectra and standard curves are given. The molar extinction coefficients have been calculated. 10 figs

  13. SIMMER-III code-verification. Phase 1

    International Nuclear Information System (INIS)

    Maschek, W.

    1996-05-01

    SIMMER-III is a computer code to investigate core disruptive accidents in liquid metal fast reactors but should also be used to investigate safety related problems in other types of advanced reactors. The code is developed by PNC with cooperation of the European partners FZK, CEA and AEA-T. SIMMER-III is a two-dimensional, three-velocity-field, multiphase, multicomponent, Eulerian, fluid-dynamics code coupled with a space-, time-, and energy-dependent neutron dynamics model. In order to model complex flow situations in a postulated disrupting core, mass and energy conservation equations are solved for 27 density components and 16 energy components, respectively. Three velocity fields (two liquid and one vapor) are modeled to simulate the relative motion of different fluid components. An additional static field takes into account the structures available in a reactor (pins, hexans, vessel structures, internal structures etc.). The neutronics is based on the discrete ordinate method (S N method) coupled into a quasistatic dynamic model. The code assessment and verification of the fluid dynamic/thermohydraulic parts of the code is performed in several steps in a joint effort of all partners. The results of the FZK contributions to the first assessment and verification phase is reported. (orig.) [de

  14. Reversed phase partition chromatographic separation of Gd(III) on poly(Crown Ether) column

    International Nuclear Information System (INIS)

    Mahanwar, K.R.; Sabale, S.R.

    2014-01-01

    A simple method has been developed for the separation of Gd(III) in hippuric acid medium by using poly(dibenzo-18-crown-6) as stationary phase. The effect of hippuric acid concentration, different eluting agent, foreign ions etc was studied and the optimum conditions were established. Breakthrough capacity of poly(dibenzo-18-crown-6) for Gd(III) was found to be 0.572 ±0.01 mmolg -1 of crown polymer. The separation of Gd(III) from other elements in multicomponent mixtures has been achieved. The method was extended for determination of Gd(III) in real sample. The method is simple, rapid and selective with good reproducibility (approximately ± 2%). Crown ethers are widely used as complexing agent that can selectively capture metal cation in their cavity. This special feature shown by poly (dibenzo-18-crown-6) has been used in our laboratory for selective cation exchanger by column chromatography. No attempts were made for the separation of Gd(III) using hippuric acid media and column chromatography. The present communication describes a simple and sensitive method for the determination of Gd(III) using poly(dibenzo-18-crown-6) as stationary phase in hippuric acid medium. The proposed method affords an attractive feature as compared to the solvent extraction technique i.e. it is free from any organic diluents as an environmental concern

  15. Phase III randomized clinical trial comparing tremelimumab with standard-of-care chemotherapy in patients with advanced melanoma

    NARCIS (Netherlands)

    Ribas, Antoni; Kefford, Richard; Marshall, Margaret A.; Punt, Cornelis J. A.; Haanen, John B.; Marmol, Maribel; Garbe, Claus; Gogas, Helen; Schachter, Jacob; Linette, Gerald; Lorigan, Paul; Kendra, Kari L.; Maio, Michele; Trefzer, Uwe; Smylie, Michael; McArthur, Grant A.; Dreno, Brigitte; Nathan, Paul D.; Mackiewicz, Jacek; Kirkwood, John M.; Gomez-Navarro, Jesus; Huang, Bo; Pavlov, Dmitri; Hauschild, Axel

    2013-01-01

    In phase I/II trials, the cytotoxic T lymphocyte-associated antigen-4-blocking monoclonal antibody tremelimumab induced durable responses in a subset of patients with advanced melanoma. This phase III study evaluated overall survival (OS) and other safety and efficacy end points in patients with

  16. Phase III randomized clinical trial comparing tremelimumab with standard-of-care chemotherapy in patients with advanced melanoma.

    NARCIS (Netherlands)

    Ribas, A.; Kefford, R.; Marshall, Martin; Punt, C.J.A.; Haanen, J.B.; Marmol, M.; Garbe, C.; Gogas, H.; Schachter, J.; Linette, G.; Lorigan, P.; Kendra, K.L.; Maio, M.; Trefzer, U.; Smylie, M.; McArthur, G.A.; Dreno, B.; Nathan, P.D.; Mackiewicz, J.; Kirkwood, J.M.; Gomez-Navarro, J.; Huang, B.; Pavlov, D.; Hauschild, A.

    2013-01-01

    PURPOSE: In phase I/II trials, the cytotoxic T lymphocyte-associated antigen-4-blocking monoclonal antibody tremelimumab induced durable responses in a subset of patients with advanced melanoma. This phase III study evaluated overall survival (OS) and other safety and efficacy end points in patients

  17. Contributions to reversed-phase column selectivity: III. Column hydrogen-bond basicity.

    Science.gov (United States)

    Carr, P W; Dolan, J W; Dorsey, J G; Snyder, L R; Kirkland, J J

    2015-05-22

    Column selectivity in reversed-phase chromatography (RPC) can be described in terms of the hydrophobic-subtraction model, which recognizes five solute-column interactions that together determine solute retention and column selectivity: hydrophobic, steric, hydrogen bonding of an acceptor solute (i.e., a hydrogen-bond base) by a stationary-phase donor group (i.e., a silanol), hydrogen bonding of a donor solute (e.g., a carboxylic acid) by a stationary-phase acceptor group, and ionic. Of these five interactions, hydrogen bonding between donor solutes (acids) and stationary-phase acceptor groups is the least well understood; the present study aims at resolving this uncertainty, so far as possible. Previous work suggests that there are three distinct stationary-phase sites for hydrogen-bond interaction with carboxylic acids, which we will refer to as column basicity I, II, and III. All RPC columns exhibit a selective retention of carboxylic acids (column basicity I) in varying degree. This now appears to involve an interaction of the solute with a pair of vicinal silanols in the stationary phase. For some type-A columns, an additional basic site (column basicity II) is similar to that for column basicity I in primarily affecting the retention of carboxylic acids. The latter site appears to be associated with metal contamination of the silica. Finally, for embedded-polar-group (EPG) columns, the polar group can serve as a proton acceptor (column basicity III) for acids, phenols, and other donor solutes. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. MAQARIN natural analogue study: phase III

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, W R; Mazurek, M; Waber, H N [Univ. of Berne (Switzerland). Institutes of Geology, Mineralogy and Petrology, Rock-Water Interaction Group (GGWW); Arlinger, J; Erlandson, A C; Hallbeck, L; Pedersen, K [Goeteborg University (Sweden). Dept. of General and Marine Microbiology; Boehlmann, W; Fritz, P; Geyer, S; Geyer, W; Hanschman, G; Kopinke, F D; Poerschmann, J [Umweltforschungszentrum Leipzig-Halle (Germany); Chambers, A V; Haworth, A; Ilett, D; Linklater, C M; Tweed, C J [AEA Technology plc, Harwell (United Kingdom); Chenery, S R.N.; Kemp, S J; Milodowski, A E; Pearce, J M; Reeder, S; Rochelle, C A; Smith, B; Wetton, P D; Wragg, J [British Geological Survey, Keyworth (United Kingdom); Clark, I D [Univ. of Ottawa (Canada). Dept. of Geology; Hodginson, E; Hughes, C R [Univ. of Manchester (United Kingdom). Dept. of Earth Sciences; Hyslop, E K [British Geological Survey, Edinburgh (United Kingdom); Karlsson, F [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Khoury, H N; Salameh, E [Univ. of Jordan, Amman (Jordan); Lagerblad, B [Cement Institute, Stockholm (Sweden); Longworth, G [Univ. of Manchester (United Kingdom). Dept. of Geology; Pitty, A F [Private consultant, Norwich (United Kingdom); Savage, D [QuantiSci Ltd, Melton Mowbray (United Kingdom); Smellie, J A.T. [ed.; Conterra AB, Uppsala (Sweden)

    1998-12-01

    This report represents the conclusion to Phase III of the Maqarin Natural Analogue Study. The main thrust was to establish the origin and chemistry of the Western Springs hyper alkaline groundwaters (Na/K enriched Ca(OH){sub 2} type) and to study their interaction with rocks of different compositions, as natural analogues to key processes that might occur at an early stage within the `alkali disturbed zone` of cementitious repositories in different host rocks. Whilst earlier studies at Maqarin were very much site-specific and process-oriented, Phase III provided a regional perspective to the geological evolution of the Maqarin region. This was made possible by greater field access which allowed a more systematic structural and geomorphological study of the area. This has resulted in a greater understanding of the age and spatial relationships concerning formation of the cement zones through spontaneous combustion of the Bituminous Marls, and the subsequent formation of high pH groundwaters at the Eastern and Western Springs locations. At the Western Springs locality, hydrochemical and hydrogeological evaluation of new and published data (plus access to unpublished data), together with detailed mineralogical and geochemical studies, helped to clarify the very earliest stage of cement leachate/host rock interaction. The data were used also to test coupled flow/transport codes developed to assess the long-term evolution of a cementitious repository. Additional objectives addressed include: a) rock matrix diffusion, b) the occurrence and chemical controls on zeolite composition, e) the occurrence and chemical controls on clay stability, and d) the role of microbes, organics and colloids in trace element transport. The Maqarin site now provides a consistent picture explaining the origin of the hyperalkaline groundwaters, and is therefore a unique location for the examination of the mechanisms and processes associated with cementitious repositories. Application of these

  19. CONVERSION EXTRACTION DESULFURIZATION (CED) PHASE III

    Energy Technology Data Exchange (ETDEWEB)

    James Boltz

    2005-03-01

    This project was undertaken to refine the Conversion Extraction Desulfurization (CED) technology to efficiently and economically remove sulfur from diesel fuel to levels below 15-ppm. CED is considered a generic term covering all desulfurization processes that involve oxidation and extraction. The CED process first extracts a fraction of the sulfur from the diesel, then selectively oxidizes the remaining sulfur compounds, and finally extracts these oxidized materials. The Department of Energy (DOE) awarded Petro Star Inc. a contract to fund Phase III of the CED process development. Phase III consisted of testing a continuous-flow process, optimization of the process steps, design of a pilot plant, and completion of a market study for licensing the process. Petro Star and the Degussa Corporation in coordination with Koch Modular Process Systems (KMPS) tested six key process steps in a 7.6-centimeter (cm) (3.0-inch) inside diameter (ID) column at gas oil feed rates of 7.8 to 93.3 liters per hour (l/h) (2.1 to 24.6 gallons per hour). The team verified the technical feasibility with respect to hydraulics for each unit operation tested and successfully demonstrated pre-extraction and solvent recovery distillation. Test operations conducted at KMPS demonstrated that the oxidation reaction converted a maximum of 97% of the thiophenes. The CED Process Development Team demonstrated that CED technology is capable of reducing the sulfur content of light atmospheric gas oil from 5,000-ppm to less than 15-ppm within the laboratory scale. In continuous flow trials, the CED process consistently produced fuel with approximately 20-ppm of sulfur. The process economics study calculated an estimated process cost of $5.70 per product barrel. The Kline Company performed a marketing study to evaluate the possibility of licensing the CED technology. Kline concluded that only 13 refineries harbored opportunity for the CED process. The Kline study and the research team's discussions

  20. MAQARIN natural analogue study: phase III

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, W R; Mazurek, M; Waber, H N [Univ. of Berne (Switzerland). Institutes of Geology, Mineralogy and Petrology, Rock-Water Interaction Group (GGWW); Arlinger, J; Erlandson, A C; Hallbeck, L; Pedersen, K [Goeteborg Univ. (Sweden). Dept. of General and Marine Microbiology; Boehlmann, W; Fritz, P; Geyer, S; Geyer, W; Hanschman, G; Kopinke, F D; Poerschmann, J [Umweltforschungszentrum Leipzig-Halle (Germany); Chambers, A V; Haworth, A; Ilett, D; Linklater, C M; Tweed, C J [AEA Technology plc, Harwell (United Kingdom); Chenery, S R.N.; Kemp, S J; Milodowski, A E; Pearce, J M; Reeder, S; Rochelle, C A; Smith, B; Wetton, P D; Wragg, J [British Geological Survey, Keyworth (United Kingdom); Clark, I D [Univ. of Ottawa (Canada). Dept. of Geology; Hodginson, E; Hughes, C R [Univ. of Manchester (United Kingdom). Dept. of Earth Sciences; Hyslop, E K [British Geological Survey, Edinburgh (United Kingdom); Karlsson, F [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Khoury, H N; Salameh, E [Univ. of Jordan, Amman (Jordan); Lagerblad, B [Cement Inst., Stockholm (Sweden); Longworth, G [Univ. of Manchester (United Kingdom). Dept. of Geology; Pitty, A F [Private consultant, Norwich (United Kingdom); Savage, D [QuantiSci Ltd, Melton Mowbray (United Kingdom); Smellie, J A.T. [ed.; Conterra AB, Uppsala (Sweden)

    1998-12-01

    This report represents the conclusion to Phase III of the Maqarin Natural Analogue Study. The main thrust was to establish the origin and chemistry of the Western Springs hyper alkaline groundwaters (Na/K enriched Ca(OH){sub 2} type) and to study their interaction with rocks of different compositions, as natural analogues to key processes that might occur at an early stage within the `alkali disturbed zone` of cementitious repositories in different host rocks. Whilst earlier studies at Maqarin were very much site-specific and process-oriented, Phase III provided a regional perspective to the geological evolution of the Maqarin region. This was made possible by greater field access which allowed a more systematic structural and geomorphological study of the area. This has resulted in a greater understanding of the age and spatial relationships concerning formation of the cement zones through spontaneous combustion of the Bituminous Marls, and the subsequent formation of high pH groundwaters at the Eastern and Western Springs locations. At the Western Springs locality, hydrochemical and hydrogeological evaluation of new and published data (plus access to unpublished data), together with detailed mineralogical and geochemical studies, helped to clarify the very earliest stage of cement leachate/host rock interaction. The data were used also to test coupled flow/transport codes developed to assess the long-term evolution of a cementitious repository. Additional objectives addressed include: a) rock matrix diffusion, b) the occurrence and chemical controls on zeolite composition, e) the occurrence and chemical controls on clay stability, and d) the role of microbes, organics and colloids in trace element transport. The Maqarin site now provides a consistent picture explaining the origin of the hyperalkaline groundwaters, and is therefore a unique location for the examination of the mechanisms and processes associated with cementitious repositories. Application of these

  1. Comprehensive Evaluation of the Geothermal Resource Potential within the Pyramid Lake Paiute Reservation Phase III Report

    Energy Technology Data Exchange (ETDEWEB)

    Noel, Donna [Pyramid Lake Paiute Tribe, Nixon, NV (United States)

    2013-12-01

    This project integrated state-of-the-art exploration technologies with a geologic framework and reservoir modeling to ultimately determine the efficacy of future geothermal production within the PLPT reservation. The information gained during this study should help the PLPT to make informed decisions regarding construction of a geothermal power plant. Additional benefits included the transfer of new technologies and geothermal data to the geothermal industry and it created and/or preserved nearly three dozen jobs accordance with the American Recovery and Reinvestment Act of 2009. A variety of tasks were conducted to achieve the above stated objectives. The following are the tasks completed within the project: 1. Permitting 2. Shallow temperature survey 3. Seismic data collection and analysis 4. Fracture stress analysis 5. Phase I reporting Permitting 7. Shallow temperature survey 8. Seismic data collection and analysis 9. Fracture stress analysis 10. Phase I reporting 11. Drilling two new wells 12. Borehole geophysics 13. Phase II reporting 14. Well testing and geochemical analysis 15. Three-dimensional geologic model 16. Three-dimensional reservoir analysis 17. Reservation wide geothermal potential analysis 18. Phase III reporting Phase I consisted of tasks 1 – 5, Phase II tasks 6 – 8, and Phase III tasks 9 – 13. This report details the results of Phase III tasks. Reports are available for Phase I, and II as separate documents.

  2. Microbial Reducibility of Fe(III Phases Associated with the Genesis of Iron Ore Caves in the Iron Quadrangle, Minas Gerais, Brazil

    Directory of Open Access Journals (Sweden)

    Ceth W. Parker

    2013-11-01

    Full Text Available The iron mining regions of Brazil contain thousands of “iron ore caves” (IOCs that form within Fe(III-rich deposits. The mechanisms by which these IOCs form remain unclear, but the reductive dissolution of Fe(III (hydroxides by Fe(III reducing bacteria (FeRB could provide a microbiological mechanism for their formation. We evaluated the susceptibility of Fe(III deposits associated with these caves to reduction by the FeRB Shewanella oneidensis MR-1 to test this hypothesis. Canga, an Fe(III-rich duricrust, contained poorly crystalline Fe(III phases that were more susceptible to reduction than the Fe(III (predominantly hematite associated with banded iron formation (BIF, iron ore, and mine spoil. In all cases, the addition of a humic acid analogue enhanced Fe(III reduction, presumably by shuttling electrons from S. oneidensis to Fe(III phases. The particle size and quartz-Si content of the solids appeared to exert control on the rate and extent of Fe(III reduction by S. oneidensis, with more bioreduction of Fe(III associated with solid phases containing more quartz. Our results provide evidence that IOCs may be formed by the activities of Fe(III reducing bacteria (FeRB, and the rate of this formation is dependent on the physicochemical and mineralogical characteristics of the Fe(III phases of the surrounding rock.

  3. CSER 00-008 use of PFP Glovebox HC-18BS for Storage and Transport of Fissionable Material

    International Nuclear Information System (INIS)

    ERICKSON, D.G.

    2000-01-01

    This CSER addresses the feasibility of increasing the allowed number of open containers and permitting the transfer and storage of fissionable material in Glovebox HC-18BS without regard to form or density (metal, oxide having an H/X (le) 20, material having unrestricted moderation and plutonium hydroxide having a plutonium density of 0.2 g/cm 3 )

  4. Strategy for decommissioning of the glove-boxes in the Belgonucleaire Dessel MOX fuel fabrication plant

    International Nuclear Information System (INIS)

    Vandergheynst, Alain; Cuchet, Jean-Marie

    2007-01-01

    Available in abstract form only. Full text of publication follows: BELGONUCLEAIRE has been operating the Dessel plant from the mid-80's at industrial scale. In this period, over 35 metric tons of plutonium (HM) was processed into almost 100 reloads of MOX fuel for commercial West-European Light Water Reactors. In late 2005, the decision was made to stop the production because of the shortage of MOX fuel market remaining accessible to BELGONUCLEAIRE after the successive capacity increases of the MELOX plant (France) and the commissioning of the SMP plant (UK). As a significant part of the decommissioning project of this Dessel plant, about 170 medium-sized glove-boxes are planned for dismantling. In this paper, after having reviewed the different specifications of ±-contaminated waste in Belgium, the authors introduce the different options considered for cleaning, size reduction and packaging of the glove-boxes, and the main decision criteria (process, α-containment, mechanization and radiation protection, safety aspects, generation of secondary waste, etc) are analyzed. The selected strategy consists in using cold cutting techniques and manual operation in shielded disposable glove-tents, and packaging α-waste in 200-liter drums for off-site conditioning and intermediate disposal. (authors)

  5. Thermal dewatering of lignite: Phase III - final report

    Energy Technology Data Exchange (ETDEWEB)

    Champagne, P J; Szladow, A J; Kybett, B D

    1981-01-01

    Phase III of this project extended the investigation of thermal dewatering on several lignite and peat samples at the temperature range up to 400 degrees C and investigated variables such as retention time, increased rates of heating and cooling, extent of trace element removal, effect of particle size and effect of dewatering under heavy and light oils. Lignites from three areas of Canada (Estevan and Coronach, Saskatchewan, and Onakawana, Ontario) and one peat sample (Garrick, Saskatchewan) were thermally dewatered. The equilibrium moisture values obtained for the dewatered products were as low as, or lower than those obtained in Phases I and II of this project (350 degrees C). However, the measured moisture contents of the thermally dewatered Saskatchewan lignites were somewhat higher than those measured in Phases I and II. The equilibrium moisture values and the moisture contents decreased with increasing temperature. An optimum balance between extent of dewatering and resulting steam pressures is obtained for a dewatering temperature between 300 and 350 degrees C. At these temperatures, residence times in the order of 15 minutes are required. (35 refs.)

  6. Enhanced Cr(VI) reduction and As(III) oxidation in ice phase: Important role of dissolved organic matter from biochar

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Xiaoling [Department of Soil and Water Science, University of Florida, Gainesville, FL 32611 (United States); Ma, Lena Q., E-mail: lqma@ufl.edu [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment, Nanjing University, Jiangsu 210046 (China); Department of Soil and Water Science, University of Florida, Gainesville, FL 32611 (United States); Gress, Julia; Harris, Willie [Department of Soil and Water Science, University of Florida, Gainesville, FL 32611 (United States); Li, Yuncong [Soil and Water Science Department, Tropical Research and Education Center, University of Florida, Homestead, FL 33031-3314 (United States)

    2014-02-01

    Graphical abstract: - Highlights: • Biochar-derived dissolved organic matter (DOM) effectively reduced Cr(VI) and oxidized As(III). • Cr(VI) and As(III) could serve as a redox couple. • Cr(VI) and As(III) redox conversion was more effective in the ice phase than aqueous phase. • FTIR and ESR showed that biochar DOM served as both electron donor and acceptor. - Abstract: This study evaluated the impact of DOM from two biochars (sugar beet tailing and Brazilian pepper) on Cr(VI) reduction and As(III) oxidation in both ice and aqueous phases with a soil DOM as control. Increasing DOM concentration from 3 to 300 mg C L{sup −1} enhanced Cr(VI) reduction from 20% to 100% and As(III) oxidation from 6.2% to 25%; however, Cr(VI) reduction decreased from 80–86% to negligible while As(III) oxidation increased from negligible to 18–19% with increasing pH from 2 to 10. Electron spin resonance study suggested semiquinone radicals in DOM were involved in As(III) oxidation while Fourier transform infrared analysis suggested that carboxylic groups in DOM participated in both Cr(VI) reduction and As(III) oxidation. During Cr(VI) reduction, part of DOM (∼10%) was oxidized to CO{sub 2}. The enhanced conversion of Cr(VI) and As(III) in the ice phase was due to the freeze concentration effect with elevated concentrations of electron donors and electron acceptors in the grain boundary. Though DOM enhanced both Cr(VI) reduction and As(III)oxidation, Cr(VI) reduction coupled with As(III) oxidation occurred in absence of DOM. The role of DOM, Cr(VI) and/or As(III) in Cr and As transformation may provide new insights into their speciation and toxicity in cold regions.

  7. Remedial Action Report for Operable Units 6-05 and 10-04, Phase III

    Energy Technology Data Exchange (ETDEWEB)

    R. P. Wells

    2007-08-15

    This Phase III remedial action report addresses the remediation of lead-contaminated soils found at the Security Training Facility STF-02 Gun Range at the Idaho National Laboratory Site. Phase I, consisting of developing and implementing institutional controls at Operble Unit 10-04 sites and developing and implementing Idaho National Laboratory Site-wide plans for both institutional controls and ecological monitoring, was addressed in a previous report. Phase II will remediate sites contaminated with trinitrotoluene and Royal Demolition Explosive. Phase IV will remediate hazards from unexploded ordnance.

  8. Computer modeling for optimal placement of gloveboxes

    International Nuclear Information System (INIS)

    Hench, K.W.; Olivas, J.D.; Finch, P.R.

    1997-08-01

    Reduction of the nuclear weapons stockpile and the general downsizing of the nuclear weapons complex has presented challenges for Los Alamos. One is to design an optimized fabrication facility to manufacture nuclear weapon primary components (pits) in an environment of intense regulation and shrinking budgets. Historically, the location of gloveboxes in a processing area has been determined without benefit of industrial engineering studies to ascertain the optimal arrangement. The opportunity exists for substantial cost savings and increased process efficiency through careful study and optimization of the proposed layout by constructing a computer model of the fabrication process. This paper presents an integrative two- stage approach to modeling the casting operation for pit fabrication. The first stage uses a mathematical technique for the formulation of the facility layout problem; the solution procedure uses an evolutionary heuristic technique. The best solutions to the layout problem are used as input to the second stage - a computer simulation model that assesses the impact of competing layouts on operational performance. The focus of the simulation model is to determine the layout that minimizes personnel radiation exposures and nuclear material movement, and maximizes the utilization of capacity for finished units

  9. Computer modeling for optimal placement of gloveboxes

    Energy Technology Data Exchange (ETDEWEB)

    Hench, K.W.; Olivas, J.D. [Los Alamos National Lab., NM (United States); Finch, P.R. [New Mexico State Univ., Las Cruces, NM (United States)

    1997-08-01

    Reduction of the nuclear weapons stockpile and the general downsizing of the nuclear weapons complex has presented challenges for Los Alamos. One is to design an optimized fabrication facility to manufacture nuclear weapon primary components (pits) in an environment of intense regulation and shrinking budgets. Historically, the location of gloveboxes in a processing area has been determined without benefit of industrial engineering studies to ascertain the optimal arrangement. The opportunity exists for substantial cost savings and increased process efficiency through careful study and optimization of the proposed layout by constructing a computer model of the fabrication process. This paper presents an integrative two- stage approach to modeling the casting operation for pit fabrication. The first stage uses a mathematical technique for the formulation of the facility layout problem; the solution procedure uses an evolutionary heuristic technique. The best solutions to the layout problem are used as input to the second stage - a computer simulation model that assesses the impact of competing layouts on operational performance. The focus of the simulation model is to determine the layout that minimizes personnel radiation exposures and nuclear material movement, and maximizes the utilization of capacity for finished units.

  10. Implementation of a spark plasma sintering facility in a hermetic glovebox for compaction of toxic, radiotoxic, and air sensitive materials

    Energy Technology Data Exchange (ETDEWEB)

    Tyrpekl, V., E-mail: vaclav.tyrpekl@ec.europa.eu, E-mail: vaclav.tyrpekl@gmail.com; Berkmann, C.; Holzhäuser, M.; Köpp, F.; Cologna, M.; Somers, J. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Wangle, T. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University in Prague, Břehová 7, Praha 1, 115 19 (Czech Republic)

    2015-02-15

    Spark plasma sintering (SPS) is a rapidly developing method for densification of powders into compacts. It belongs to the so-called “field assisted sintering techniques” that enable rapid sintering at much lower temperatures than the classical approaches of pressureless sintering of green pellets or hot isostatic pressing. In this paper, we report the successful integration of a SPS device into a hermetic glovebox for the handling of highly radioactive material containing radioisotopes of U, Th, Pu, Np, and Am. The glovebox implantation has been facilitated by the replacement of the hydraulic system to apply pressure with a compact electromechanical unit. The facility has been successfully tested using UO{sub 2} powder. Pellets with 97% of the theoretical density were obtained at 1000 °C for 5 min, significantly lower than the ∼1600 °C for 5-10 h used in conventional pellet sintering.

  11. Gas-phase infrared spectrum of phosphorus (III) oxycyanide, OPCN: experimental and theoretical investigations

    Science.gov (United States)

    Allaf, Abdul. W.; Kassem, M.; Alibrahim, M.; Boustani, Ihsan

    1999-03-01

    An attempt was made to observe the gas-phase infrared spectrum of Phosphorus (III) oxycyanide, OPCN for the first time. This molecule was produced by an on-line process using phosphorus (III) oxychloride, OPCl as precursor passed over heated AgCN. The products were characterised by the infrared spectra of their vapours. The low resolution gas-phase Fourier transform infrared spectrum shows two bands centered at 2165 and 1385 cm -1. These bands are assigned to, ν1 (CN stretch) and ν2 (OP stretch), respectively. Ab initio self-consistent-field (SCF) molecular orbital (MO) and Møller-Plesset second order perturbation theory (MP2) calculations were performed to determine the geometry, total energy and vibrational frequencies of OPCN.

  12. Glovebox glove deterioration in the Hanford Engineering Development Laboratory fuel fabrication facility

    International Nuclear Information System (INIS)

    Greenhalgh, W.O.; Smith, R.C.; Powell, D.L.

    1979-07-01

    Neoprene glovebox gloves have been found susceptible to periodic rapid deterioration under normal operating conditions in fuel fabrication facilities. Examinations of glove failure histories and measurements of the atmospheres in inert atmosphere dry-boxes indicated ozone at low concentrations of 100 to 500 ppB was probably the most important factor in rapid glove deterioration. Testing of a varity of new glove materials indicated that Hypalon and ethylene-propylene-diamine monomer (EDPM) gloves have greater than 30 times the longevity of neoprene in low-level ozone concentration atmospheres. comparative tests over a 30-month period have also confirmed that the two glove candidates have a significantly longer operative life. 14 figures

  13. Calculation note - Consequences of a fire in the sorting and repackaging glovebox in room 636 of bldg 2736-ZB - Plutonium Finishing Plant

    International Nuclear Information System (INIS)

    JOHNSON, L.E.

    1999-01-01

    This Calculation Note provides a conservative estimate of the grams of plutonium released from Building 2736-ZB of the Plutonium Finishing Plant as a result of a fire within Glovebox 636, without consideration of mitigation

  14. In-Situ Leak Testing And Replacement Of Glovebox Isolator, Or Containment Unit Gloves

    Science.gov (United States)

    Castro, Julio M.; Macdonald, John M.; Steckle, Jr., Warren P.

    2004-11-02

    A test plug for in-situ testing a glove installed in a glovebox is provided that uses a top plate and a base plate, and a diametrically expandable sealing mechanism fitting between the two plates. The sealing mechanism engages the base plate to diametrically expand when the variable distance between the top plate and the bottom plate is reduced. An inlet valve included on the top plate is used to introducing a pressurized gas to the interior of the glove, and a pressure gauge located on the top plate is used to monitor the interior glove pressure.

  15. Microgravity Science Glovebox (MSG) Space Science's Past, Present, and Future on the International Space Station (ISS)

    Science.gov (United States)

    Spivey, Reggie A.; Spearing, Scott F.; Jordan, Lee P.; McDaniel S. Greg

    2012-01-01

    The Microgravity Science Glovebox (MSG) is a double rack facility designed for microgravity investigation handling aboard the International Space Station (ISS). The unique design of the facility allows it to accommodate science and technology investigations in a "workbench" type environment. MSG facility provides an enclosed working area for investigation manipulation and observation in the ISS. Provides two levels of containment via physical barrier, negative pressure, and air filtration. The MSG team and facilities provide quick access to space for exploratory and National Lab type investigations to gain an understanding of the role of gravity in the physics associated research areas. The MSG is a very versatile and capable research facility on the ISS. The Microgravity Science Glovebox (MSG) on the International Space Station (ISS) has been used for a large body or research in material science, heat transfer, crystal growth, life sciences, smoke detection, combustion, plant growth, human health, and technology demonstration. MSG is an ideal platform for gravity-dependent phenomena related research. Moreover, the MSG provides engineers and scientists a platform for research in an environment similar to the one that spacecraft and crew members will actually experience during space travel and exploration. The MSG facility is ideally suited to provide quick, relatively inexpensive access to space for National Lab type investigations.

  16. The majority of patients with metastatic melanoma are not represented in pivotal phase III immunotherapy trials

    DEFF Research Database (Denmark)

    Donia, Marco; Kimper-Karl, Marie Louise; Høyer, Katrine Lundby

    2017-01-01

    BACKGROUND: Recent randomised phase III trials have led to the approval of several immune checkpoint inhibitors for unresectable or metastatic melanoma (MM). These trials all employed strict patient selection criteria, and it is currently unknown how large proportion of 'real-world' patients diag...... a huge knowledge gap regarding the usefulness of new immunotherapies in the 'real-world' patient population, and urge additional testing of known regimens in selected poor prognosis cohorts.......BACKGROUND: Recent randomised phase III trials have led to the approval of several immune checkpoint inhibitors for unresectable or metastatic melanoma (MM). These trials all employed strict patient selection criteria, and it is currently unknown how large proportion of 'real-world' patients...... in 2014, were included in the analysis. Seven pre-defined eligibility criteria, all used to select patients for enrolment in five recent randomised phase III immunotherapy trials, were analysed. RESULTS: Fifty-five percent of the total population with MM did not meet one or more eligibility criteria ('not...

  17. The role of technology in reducing health care costs. Phase II and phase III.

    Energy Technology Data Exchange (ETDEWEB)

    Cilke, John F.; Parks, Raymond C.; Funkhouser, Donald Ray; Tebo, Michael A.; Murphy, Martin D.; Hightower, Marion Michael; Gallagher, Linda K.; Craft, Richard Layne, II; Garcia, Rudy John

    2004-04-01

    In Phase I of this project, reported in SAND97-1922, Sandia National Laboratories applied a systems approach to identifying innovative biomedical technologies with the potential to reduce U.S. health care delivery costs while maintaining care quality. The effort provided roadmaps for the development and integration of technology to meet perceived care delivery requirements and an economic analysis model for development of care pathway costs for two conditions: coronary artery disease (CAD) and benign prostatic hypertrophy (BPH). Phases II and III of this project, which are presented in this report, were directed at detailing the parameters of telemedicine that influence care delivery costs and quality. These results were used to identify and field test the communication, interoperability, and security capabilities needed for cost-effective, secure, and reliable health care via telemedicine.

  18. Zwitterion-functionalized polymer microspheres as a sorbent for solid phase extraction of trace levels of V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) prior to their determination by ICP-MS.

    Science.gov (United States)

    Jia, Xiaoyu; Gong, Dirong; Zhao, Junyi; Ren, Hongyun; Wang, Jiani; Zhang, Xian

    2018-03-19

    This paper describes the preparation of zwitterion-functionalized polymer microspheres (ZPMs) and their application to simultaneous enrichment of V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) from environmental water samples. The ZPMs were prepared by emulsion copolymerization of ethyl methacrylate, 2-diethylaminoethyl methacrylate and triethylene glycol dimethyl acrylate followed by modification with 1,3-propanesultone. The components were analyzed by elemental analyses as well as Fourier transform infrared spectroscopy, and the structures were characterized by scanning electron microscopy and transmission electron microscopy. The ZPMs were packed into a mini-column for on-line solid-phase extraction (SPE) of the above metal ions. Following extraction with 40 mM NH 4 NO 3 and 0.5 M HNO 3 solution, the ions were quantified by ICP-MS. Under the optimized conditions, the enrichment factors (from a 40 mL sample) are up to 60 for the ions V(V), As(III), Sb(III) and Hg(II), and 55 for Cr(III) and Sn(IV). The detection limits are 1.2, 3.4, 1.0, 3.7, 2.1 and 1.6 ng L -1 for V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II), respectively, and the relative standard deviations (RSDs) are below 5.2%. The feasibility and accuracy of the method were validated by successfully analyzing six certified reference materials as well as lake, well and river waters. Graphical abstract Zwitterion-functionalized polymer microspheres (ZPMs) were prepared and packed into a mini-column for on-line solid-phase extraction (SPE) via pump 1. Then V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) ions in environmental waters were eluted and submitted to ICP-MS via pump 2.

  19. Phase 0 and phase III transport in various organs: combined concept of phases in xenobiotic transport and metabolism.

    Science.gov (United States)

    Döring, Barbara; Petzinger, Ernst

    2014-08-01

    The historical phasing concept of drug metabolism and elimination was introduced to comprise the two phases of metabolism: phase I metabolism for oxidations, reductions and hydrolyses, and phase II metabolism for synthesis. With this concept, biological membrane barriers obstructing the accessibility of metabolism sites in the cells for drugs were not considered. The concept of two phases was extended to a concept of four phases when drug transporters were detected that guided drugs and drug metabolites in and out of the cells. In particular, water soluble or charged drugs are virtually not able to overcome the phospholipid membrane barrier. Drug transporters belong to two main clusters of transporter families: the solute carrier (SLC) families and the ATP binding cassette (ABC) carriers. The ABC transporters comprise seven families with about 20 carriers involved in drug transport. All of them operate as pumps at the expense of ATP splitting. Embedded in the former phase concept, the term "phase III" was introduced by Ishikawa in 1992 for drug export by ABC efflux pumps. SLC comprise 52 families, from which many carriers are drug uptake transporters. Later on, this uptake process was referred to as the "phase 0 transport" of drugs. Transporters for xenobiotics in man and animal are most expressed in liver, but they are also present in extra-hepatic tissues such as in the kidney, the adrenal gland and lung. This review deals with the function of drug carriers in various organs and their impact on drug metabolism and elimination.

  20. Safety systems and safety analysis of the Qinshan phase III CANDU nuclear power plant

    International Nuclear Information System (INIS)

    Cai Jianping; Shen Sen; Barkman, N.

    1999-01-01

    The author introduces the Canadian nuclear reactor safety philosophy and the Qinshan Phase III CANDU NPP safety systems and safety analysis, which are designed and performed according to this philosophy. The concept of 'defence-in-depth' is a key element of the Canadian nuclear reactor safety philosophy. The design concepts of redundancy, diversity, separation, equipment qualification, quality assurance, and use of appropriate design codes and standards are adopted in the design. Four special safety systems as well as a set of reliable safety support systems are incorporated in the design of Qinshan phase III CANDU for accident mitigation. The assessment results for safety systems performance show that the fundamental safety criteria for public dose, and integrity of fuel, channels and the reactor building, are satisfied

  1. Motivation and participation in a phase III cardiac rehabilitation programme: an application of the health action process approach.

    Science.gov (United States)

    Dohnke, Birte; Nowossadeck, Enno; Müller-Fahrnow, Werner

    2010-10-01

    This longitudinal study extends the previous research on low participation rates and high dropout rates in phase III cardiac rehabilitation (CR) exercise programmes. It examines the correlates of motivation and participation 6 months after inpatient phase II CR (T1) and the predictors of dropout 6 months later (T2) using the health action process approach (HAPA). Risk perception, outcome expectancies, self-efficacy, intention (at T1), and participation (at T1 and T2) in relation to phase III CR programmes was assessed in 456 patients. Based on intention and participation at T1, patients were classified as nonintenders (56%), intenders (13%), or actors (31%). Group differences were confirmed in outcome expectancies and self-efficacy. By T2, 21% of T1 actors had dropped out. Dropouts and maintainers differed in intention and self-efficacy (at T1). Results are in line with the HAPA and suggest a perspective for tailoring motivational counselling to improve participation in phase III CR programmes.

  2. Steady-state heat and particle removal with the actively cooled Phase III outboard pump limiter in Tore Supra

    International Nuclear Information System (INIS)

    Nygren, R.; Koski, J.; Lutz, T.; McGrath; Miller, J.; Watkins, J.; Guilhem, D.; Chappuis, P.; Cordier, J.; Loarer, T.

    1995-01-01

    Tore Supra's Phase III outboard pump limiter (OPL) is a modular actively-cooled mid-plane limiter, designed for heat and particle removal during long pulse operation. During its initial operation in 1993, the OPL successfully removed about 1 MW of power during ohmicly heated shots of up to 10 s duration and reached (steady state) thermal equilibrium. The particle pumping of the Phase III OPL was found to be about 50% greater than the Phase II OPL which had a radial distance between the last closed flux surface and the entrance of the pumping throat of 3.5 cm compared with only 2.5 cm for the Phase III OPL. This paper gives examples of power distribution over the limiter from IR measurements of surface temperature and from extensively calorimetry (34 thermocouples and 10 flow meters) and compares the distributions with values predicted by a 3D model (HF3D) with a detailed magnetic configuration (e.g., includes field ripple). ((orig.))

  3. Acceptance test procedure, 241-SY-101 Flexible Receiver System, Phase III testing

    International Nuclear Information System (INIS)

    Ritter, G.A.

    1994-01-01

    This Acceptance Test Procedure is for the 241-SY-101 Flexible Receiver System, Phase III Testing. This procedure will test the sealing integrity of the Flexible Receiver System to ensure that release of waste and aerosols will be minimized during the removal of the test mixer pump from tank SY-101

  4. Luminescence studies of Sm(III) and Cm(III) complexes in NaSCN/DHDECMP extraction systems

    CERN Document Server

    Chung, D Y; Kimura, T

    1999-01-01

    Laser-induced fluorescence (LIF) studies of Sm(III) and Cm(III) complexes in the NaSCN/DHDECMP solvent extraction system were carried out. Luminescence lifetimes were measured to determine the number of water molecules coordinated to Sm(III), Tb(III), Dy(III), and Cm(III) in the sodium thiocyanate solution and in the DHDECMP phase. The hydration number of Sm(III), Tb(III), Dy(III), and Cm(III) in the sodium thiocyanate solution decreased linearly with increasing sodium thiocyanate concentration. The hydration numbers of Sm(III), Dy(III), and Cm(III) in the DHDECMP phase decreased with increasing sodium thiocyanate concentration. The water molecules in the inner coordination sphere of Sm(III) and Dy(III) extracted into the DHDECMP were not completely removed at low sodium thiocyanate concentration but decreased with increasing sodium thiocyanate concentration. However, in the case of Cm(III) extracted into the DHDECMP phase from the sodium thiocyanate solution, there was no water in the inner coordination sphe...

  5. Solvent extraction of anionic chelate complexes of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) with 2-thenoyltrifluoroacetone as ion-pairs with tetrabutylammonium ions

    International Nuclear Information System (INIS)

    Noro, Junji; Sekine, Tatsuya.

    1992-01-01

    The solvent extraction of lanthanum(III), europium(III), lutetium(III), scandium(III), and indium(III) in 0.1 mol dm -3 sodium nitrate solutions with 2-thenoyltrifluoroacetone (Htta) in the absence and presence of tetrabutylammonium ions (tba + ) into carbon tetrachloride was measured. The extraction of lanthanum(III), europium(III), and lutetium(III) was greatly enhanced by the addition of tba + ; this could be explained in terms of the extraction of a ternary complex, M(tta) 4 - tba + . However, the extractions of scandium(III) and indium(III) were nearly the same when tba + was added. The data were treated on the basis of the formation equilibrium of the ternary complex from the neutral chelate, M(tta) 3 , with the extracted ion-pairs of the reagents, tta - tba + , in the organic phase. It was concluded that the degree of association of M(tta) 3 with the ion-pair, tta - tba + , is greater in the order La(tta) 3 ≅ Eu(tta) 3 > Lu(tta) 3 , or that the stability of the ternary complex in the organic phase is higher in the order La(tta) 4 - tba + ≅ Eu(tta) 4 - tba + > Lu(tta) 4 - tba + . This is similar to those of adduct metal chelates of Htta with tributylphosphate (TBP) in synergistic extraction systems. (author)

  6. Gas-phase infrared spectrum of phosphorus (III) oxycyanide, OPCN: Experimental and theoretical and theoretical investigations

    International Nuclear Information System (INIS)

    Allaf, A.W.; Kassem, M.; Alibrahim, M.

    1999-01-01

    An attempt was made to observe the gas-phase infrared spectrum of phosphorus (III) oxycyanide, OPCN for the first time. This molecule was produced by on-line process using phosphorus (III) oxychloride, OPCI as precursor passed over heated Ag CN. The products were characterised by the infrared spectra of their vapours. The low resolution gas-phase Fourier transform infrared spectrum shows two bands at 2165 and 1385 cm -1 . These bands are assigned to ν 1 (C≡N stretch) and ν 2 (O=P stretch), respectively. Ab initio self-consistent-field (SCF) molecular orbital (MO) and Moeller - Plesset second order perturbation theory (MP2) calculations were performed to determine the geometry, total energy and vibrational frequencies of OPCN. (authors)

  7. SPSP Phase III Recruiting, Selecting, and Developing Secure Power Systems Professionals. Job Profiles

    Energy Technology Data Exchange (ETDEWEB)

    O' Neil, Lori Ross [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Conway, T. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tobey, D. H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Greitzer, Frank L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Dalton, Angela C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pusey, Portia K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-03-01

    The Secure Power Systems Professional Phase III final report was released last year which an appendix of Job Profiles. This new report is that appendix broken out as a standalone document to assist utilities in recruiting and developing Secure Power Systems Professionals at their site.

  8. CSER 99-002: CSER for unrestricted moderation of sludge material with two-boat operations in gloveboxes HC-21A and HC-21C

    International Nuclear Information System (INIS)

    LAN, J.S.

    1999-01-01

    This Criticality Safety Evaluation Report was prepared by Fluor Daniel Northwest under contract to BWHC. This document establishes the criticality safety parameters for unrestricted moderation of Sludge material with two-boat operations in gloveboxes HC-21A and HC-21C

  9. INL Results for Phases I and III of the OECD/NEA MHTGR-350 Benchmark

    Energy Technology Data Exchange (ETDEWEB)

    Gerhard Strydom; Javier Ortensi; Sonat Sen; Hans Hammer

    2013-09-01

    The Idaho National Laboratory (INL) Very High Temperature Reactor (VHTR) Technology Development Office (TDO) Methods Core Simulation group led the construction of the Organization for Economic Cooperation and Development (OECD) Modular High Temperature Reactor (MHTGR) 350 MW benchmark for comparing and evaluating prismatic VHTR analysis codes. The benchmark is sponsored by the OECD's Nuclear Energy Agency (NEA), and the project will yield a set of reference steady-state, transient, and lattice depletion problems that can be used by the Department of Energy (DOE), the Nuclear Regulatory Commission (NRC), and vendors to assess their code suits. The Methods group is responsible for defining the benchmark specifications, leading the data collection and comparison activities, and chairing the annual technical workshops. This report summarizes the latest INL results for Phase I (steady state) and Phase III (lattice depletion) of the benchmark. The INSTANT, Pronghorn and RattleSnake codes were used for the standalone core neutronics modeling of Exercise 1, and the results obtained from these codes are compared in Section 4. Exercise 2 of Phase I requires the standalone steady-state thermal fluids modeling of the MHTGR-350 design, and the results for the systems code RELAP5-3D are discussed in Section 5. The coupled neutronics and thermal fluids steady-state solution for Exercise 3 are reported in Section 6, utilizing the newly developed Parallel and Highly Innovative Simulation for INL Code System (PHISICS)/RELAP5-3D code suit. Finally, the lattice depletion models and results obtained for Phase III are compared in Section 7. The MHTGR-350 benchmark proved to be a challenging simulation set of problems to model accurately, and even with the simplifications introduced in the benchmark specification this activity is an important step in the code-to-code verification of modern prismatic VHTR codes. A final OECD/NEA comparison report will compare the Phase I and III

  10. Analysis of gas-liquid metal two-phase flows using a reactor safety analysis code SIMMER-III

    International Nuclear Information System (INIS)

    Suzuki, Tohru; Tobita, Yoshiharu; Kondo, Satoru; Saito, Yasushi; Mishima, Kaichiro

    2003-01-01

    SIMMER-III, a safety analysis code for liquid-metal fast reactors (LMFRs), includes a momentum exchange model based on conventional correlations for ordinary gas-liquid flows, such as an air-water system. From the viewpoint of safety evaluation of core disruptive accidents (CDAs) in LMFRs, we need to confirm that the code can predict the two-phase flow behaviors with high liquid-to-gas density ratios formed during a CDA. In the present study, the momentum exchange model of SIMMER-III was assessed and improved using experimental data of two-phase flows containing liquid metal, on which fundamental information, such as bubble shapes, void fractions and velocity fields, has been lacking. It was found that the original SIMMER-III can suitably represent high liquid-to-gas density ratio flows including ellipsoidal bubbles as seen in lower gas fluxes. In addition, the employment of Kataoka-Ishii's correlation has improved the accuracy of SIMMER-III for gas-liquid metal flows with cap-shape bubbles as identified in higher gas fluxes. Moreover, a new procedure, in which an appropriate drag coefficient can be automatically selected according to bubble shape, was developed. Through this work, the reliability and the precision of SIMMER-III have been much raised with regard to bubbly flows for various liquid-to-gas density ratios

  11. The third phase of the OECD/NEA TDB project: TDB III

    International Nuclear Information System (INIS)

    Mompean, F.J.; Illemassene, M.; Perrone, J.

    2005-01-01

    In 2003 with a foreseen duration of four years. The main objective of this new phase is to extend the existing critically reviewed database for elements of relevance in radioactive waste management, paying attention to the needs of the various national programmes. Following the decision by the Project Management Board (integrated by representatives of 16 organisations with responsibilities in radioactive waste management in 12 OECD member countries) the elements contemplated in this new phase are Th, Sn and Fe, with a higher priority being allocated to inorganic species and compounds. In addition to the corresponding review teams for these elements, an additional expert team has been constituted to prepare guidelines for the evaluation of thermodynamic data for solid solutions. As was the case in TDB Phase II, the basic project review methodology remains unaltered in TDB III. The Figure illustrates the relationship between the various TDB bodies, with an International Organisation, the OECD NEA, acting as Project Coordinator and linking the independent scientific teams and the project governing bodies. This organizational paradigm has proven successful with the recent completion of the five Phase II Reviews (Update, Ni, Se, Zr and Organic Ligands). The review and expert team activities were started in 2004 (except for Fe, being started in 2005) following an initiation stage. This preliminary stage was designed in order to tailor the team compositions to the existing literature for each element. The first reviews stemming from TDB III are scheduled to appear in published form in 2007. The successful completion of these objectives will add three further reports to the current series of nine volumes (dealing with the chemical thermodynamics of U, Np, Pu, Am, Tc, Ni, Se, Zr and compounds and complexes of these elements with oxalate, citrate, EDTA and isa). (authors)

  12. Study of complex formation of cobalt (II) and cobalt (III) in acrylamide aqueous solutions and in the phase of acrylamide hydrogel

    International Nuclear Information System (INIS)

    Ismailova, M.M.; Egorova, L.A.; Khamidov, B.O.

    1993-01-01

    Present article is devoted to study of complex formation of cobalt (II) and cobalt (III) in acrylamide aqueous solutions and in the phase of acrylamide hydrogel. The condition of cobalt in various rate of oxidation in acrylamide aqueous solutions was studied. The concentration conditions of stability of system Co(II)-Co(III) were defined. The composition of coordination compounds of cobalt (II) and cobalt (III) in acrylamide aqueous solutions and in the phase of acrylamide hydrogel was determined.

  13. Encyclopedia of two-phase heat transfer and flow III macro and micro flow boiling and numerical modeling fundamentals

    CERN Document Server

    2018-01-01

    Set III of this encyclopedia is a new addition to the previous Sets I and II. It contains 26 invited chapters from international specialists on the topics of numerical modeling of two-phase flows and evaporation, fundamentals of evaporation and condensation in microchannels and macrochannels, development and testing of micro two-phase cooling systems for electronics, and various special topics (surface wetting effects, microfin tubes, two-phase flow vibration across tube bundles). The chapters are written both by renowned university researchers and by well-known engineers from leading corporate research laboratories. Numerous "must read" chapters cover the fundamentals of research and engineering practice on boiling, condensation and two-phase flows, two-phase heat transfer equipment, electronics cooling systems, case studies and so forth. Set III constitutes a "must have" reference together with Sets I and II for thermal engineering researchers and practitioners.

  14. Integrated Monitoring and Surveillance System demonstration project. Phase 2 accomplishments

    International Nuclear Information System (INIS)

    Aumeier, S.E.; Walters, B.G.; Singleterry, R.C.

    1997-01-01

    The paper presents the results of the Integrated Monitoring and Surveillance System (IMSS) demonstration project Phase 2 efforts. the rationale behind IMSS development is reviewed and progress in each of the 5 basic tasks is detailed. Significant results include further development of the data acquisition system and procurement of necessary hardware/software, options and associated costs for plutonium canning systems and gloveboxes, initiation of facility modifications, determination of possibly affected facility documentation, results from sensor system trade study, and preliminary storage configuration designs. Resources invested during Phase 1 and Phase 2 are summarized and budgetary requirements for completion of Phase 3 presented. The results show that the IMSS demonstration project team has met and in many cases exceeded the commitments made for Phase 2 deliverables

  15. Imprinted magnetic graphene oxide for the mini-solid phase extraction of Eu (III) from coal mine area

    Science.gov (United States)

    Patra, Santanu; Roy, Ekta; Madhuri, Rashmi; Sharma, Prashant K.

    2017-05-01

    The present work represents the preparation of imprinted magnetic reduced graphene oxide and applied it for the selective removal of Eu (III) from local coal mines area. A simple solid phase extraction method was used for this purpose. The material shows a very high adsorption as well as removal efficiency towards Eu (III), which suggest that the material have potential to be used in future for their real time applications in removal of Eu (III) from complex matrices.

  16. A survey of Type III restriction-modification systems reveals numerous, novel epigenetic regulators controlling phase-variable regulons; phasevarions

    Science.gov (United States)

    Atack, John M; Yang, Yuedong; Jennings, Michael P

    2018-01-01

    Abstract Many bacteria utilize simple DNA sequence repeats as a mechanism to randomly switch genes on and off. This process is called phase variation. Several phase-variable N6-adenine DNA-methyltransferases from Type III restriction-modification systems have been reported in bacterial pathogens. Random switching of DNA methyltransferases changes the global DNA methylation pattern, leading to changes in gene expression. These epigenetic regulatory systems are called phasevarions — phase-variable regulons. The extent of these phase-variable genes in the bacterial kingdom is unknown. Here, we interrogated a database of restriction-modification systems, REBASE, by searching for all simple DNA sequence repeats in mod genes that encode Type III N6-adenine DNA-methyltransferases. We report that 17.4% of Type III mod genes (662/3805) contain simple sequence repeats. Of these, only one-fifth have been previously identified. The newly discovered examples are widely distributed and include many examples in opportunistic pathogens as well as in environmental species. In many cases, multiple phasevarions exist in one genome, with examples of up to 4 independent phasevarions in some species. We found several new types of phase-variable mod genes, including the first example of a phase-variable methyltransferase in pathogenic Escherichia coli. Phasevarions are a common epigenetic regulation contingency strategy used by both pathogenic and non-pathogenic bacteria. PMID:29554328

  17. Ultracompact electro-optic phase modulator based on III-V-on-silicon microdisk resonator.

    Science.gov (United States)

    Lloret, J; Kumar, R; Sales, S; Ramos, F; Morthier, G; Mechet, P; Spuesens, T; Van Thourhout, D; Olivier, N; Fédéli, J-M; Capmany, J

    2012-06-15

    A novel ultracompact electro-optic phase modulator based on a single 9 μm-diameter III-V microdisk resonator heterogeneously integrated on and coupled to a nanophotonic waveguide is presented. Modulation is enabled by effective index modification through carrier injection. Proof-of-concept implementation involving binary phase shift keying modulation format is assembled. A power imbalance of ∼0.6  dB between both symbols and a modulation rate up to 1.8 Gbps are demonstrated without using any special driving technique.

  18. Stakeholder perspectives on the use of positron emission tomography in phase III oncology trials in the UK.

    Science.gov (United States)

    Rojas-Anaya, Hector; Skogen, Karoline; Miles, Kenneth Alan

    2012-06-01

    To identify factors that influence the use of PET in phase III oncology trials in the UK by evaluating stakeholder perspectives. A wide range of UK PET research stakeholders with a potential interest in the use of PET in phase III trials were identified and invited to participate. These UK PET research stakeholders were consulted using a semistructured questionnaire on their personal experience with and involvement in PET research, the role of PET in phase III oncology clinical trials and on the promotion of UK PET research and unmet clinical needs in oncology. Responses were analysed quantitatively and by qualitative content analysis of free-text responses. A total of 118 responses were received from a wide range of stakeholders representing several professional groups and working environments. Of these respondents, 49 (42%) were using PET in their research. There was the general perception that using PET in clinical research is beneficial in oncology. The two major barriers identified were poor availability of PET and perceived difficulties in funding of excess treatment costs (75% of respondents). Other factors included limited coverage of PET in training, uncertainty about developing imaging protocols or the status of tracers other than 18F-fluorodeoxyglucose, and low awareness of the role of PET in patient selection for therapeutic trials. Patient concerns about radiation were not perceived as a research barrier. Interventions that improve the availability and funding pathways for PET research scans and that increase researcher awareness could help promote the use of PET for phase III oncology trials in the UK.

  19. Radiotherapy in carcinoma of the uterine cervix phase III

    Energy Technology Data Exchange (ETDEWEB)

    Alvarez Villa, O; Reinerio, A; Felipe Castillo, A; Alonso Pantiga, R; Roig, M

    1985-01-01

    Between April 1968 and December 1980, 61 patients with phase III cancer of the cervix were treated. Fifty-six of them were squamous-cell carcinomas and five adenocarcinomas. The treatment consisted of a combination of external irradiation at doses varying between 4,000 and 7,000 rads and intracavitary radiotherapy with doses of 4.000 to 6.000 MHz, according to the schemes of the D.M. Anderson of Houston. The results obtained as far as survival is concerned and calculated by the actuarial method were 40% after five and ten years. The local control rate reached was 74%. The severe complications caused by the treatment reached 8.1%.

  20. Single-crystal neutron diffraction study of ammonium nitrate phase III

    International Nuclear Information System (INIS)

    Choi, C.S.; Prask, H.J.

    1982-01-01

    The crystal structure of ammonium nitrate phase III has been studied at room temperature by neutron diffraction using a single crystal containing 5% KNO 3 in solid-solution form. The space group is Pnma, with a = 7.6772 (4), b = 5.8208 (4), c = 7.1396 (5) A, Z = 4. The final residual after full-matrix least-squares refinement was R = 0.042 for 348 observed reflections. The ammonium ions are thermally disordered into two orientations, displaced by an angle of approximately 42 0 about an axis parallel to the c axis. (Auth.)

  1. Glovebox-contained forty-millimeter gun system for the study of one-dimensional shock waves in toxic materials

    International Nuclear Information System (INIS)

    Honodel, C.A.

    1975-01-01

    A new gun system is being constructed at the Lawrence Livermore Laboratory for studies of the behavior of toxic materials under shock-loaded conditions. Due to the extreme toxicity of some materials, such as plutonium, the entire gun system must be enclosed in gloveboxes. Some of the experimental requirements that affected the design of the system, various diagnostic techniques that will be employed with the system, and some details of the final design that is presently under assembly are presented

  2. Whole Brain Radiotherapy and RRx-001: Two Partial Responses in Radioresistant Melanoma Brain Metastases from a Phase I/II Clinical Trial: A TITE-CRM Phase I/II Clinical Trial.

    Science.gov (United States)

    Kim, Michelle M; Parmar, Hemant; Cao, Yue; Pramanik, Priyanka; Schipper, Matthew; Hayman, James; Junck, Larry; Mammoser, Aaron; Heth, Jason; Carter, Corey A; Oronsky, Arnold; Knox, Susan J; Caroen, Scott; Oronsky, Bryan; Scicinski, Jan; Lawrence, Theodore S; Lao, Christopher D

    2016-04-01

    Kim et al. report two patients with melanoma metastases to the brain that responded to treatment with RRx-001 and whole brain radiotherapy (WBRT) without neurologic or systemic toxicity in the context of a phase I/II clinical trial. RRx-001 is an reactive oxygen and reactive nitrogen species (ROS/RNS)-dependent systemically nontoxic hypoxic cell radiosensitizer with vascular normalizing properties under investigation in patients with various solid tumors including those with brain metastases. Metastatic melanoma to the brain is historically associated with poor outcomes and a median survival of 4 to 5 months. WBRT is a mainstay of treatment for patients with multiple brain metastases, but no significant therapeutic advances for these patients have been described in the literature. To date, candidate radiosensitizing agents have failed to demonstrate a survival benefit in patients with brain metastases, and in particular, no agent has demonstrated improved outcome in patients with metastatic melanoma. Kim et al. report two patients with melanoma metastases to the brain that responded to treatment with novel radiosensitizing agent RRx-001 and WBRT without neurologic or systemic toxicity in the context of a phase I/II clinical trial. Published by Elsevier Inc.

  3. Safety and hemostatic efficacy of fibrin pad in partial nephrectomy: Results of an open-label Phase I and a randomized, standard-of-care-controlled Phase I/II study

    Directory of Open Access Journals (Sweden)

    Nativ Ofer

    2012-11-01

    Full Text Available Abstract Background Bleeding severity, anatomic location, tissue characteristics, and visibility are common challenges encountered while managing intraoperative bleeding, and conventional hemostatic measures (suture, ligature, and cautery may sometimes be ineffective or impractical. While topical absorbable hemostats (TAH are useful hemostatic adjuvants, each TAH has associated disadvantages. Methods We evaluated the safety and hemostatic efficacy of a new advanced biologic combination product―fibrin pad―to potentially address some gaps associated with TAHs. Fibrin pad was assessed as adjunctive hemostat in open partial nephrectomy in single-center, open-label, Phase I study (N = 10, and as primary hemostat in multicenter, single-blind, randomized, standard-of-care (SOC-controlled Phase I/II study (N = 7 in Israel. It was used to control mild-to-moderate bleeding in Phase I and also spurting arterial bleeding in Phase I/II study. Phase I study assessed safety and Phase I/II study, proportion of successes at 10 min following randomization, analyzed by Fisher exact tests at 5% significance level. Results Phase I (N = 10: All patients completed the study. Hemostasis was achieved within 3–4 min (average = 3.1 min of a single application in all patients. Fibrin pad was found to be safe for human use, with no product-related adverse events reported. Phase I/II (N = 7: Hemostatic success at 10 min (primary endpoint was achieved in 3/4 patients treated with fibrin pad versus 0/3 patients treated with SOC. No clinically significant change in laboratory or coagulation parameters was recorded, except a case of post-procedural hemorrhage with fibrin pad, which was considered serious and related to the fibrin pad treatment, and required re-operation. Although Data Safety Monitoring Board authorized trial continuation, the sponsor decided against proceeding toward an indication for primary treatment of severe arterial

  4. An open-walled ionization chamber appropriate to tritium monitoring for glovebox

    International Nuclear Information System (INIS)

    Chen Zhilin; Chang Ruiming; Mu Long; Song Guoyang; Wang Heyi; Wu Guanyin; Wei Xiye

    2010-01-01

    An open-walled ionization chamber is developed to monitor the tritium concentration in gloveboxes in tritium processing systems. Two open walls are used to replace the sealed wall in common ionization chambers, through which the tritium gas can diffuse into the chamber without the aid of pumps and pipelines. Some basic properties of the chamber are examined to evaluate its performance. Results turn out that an open-walled chamber of 1 l in volume shows a considerably flat plateau over 700 V for a range of tritium concentration. The chamber also gives a good linear response to gamma fields over 4 decades under a pressure condition of 1 atm. The pressure dependence characteristics show that the ionization current is only sensitive at low pressures. The pressure influence becomes weaker as the pressure increases mainly due to the decrease in the mean free path of β particles produced by tritium decay. The minimum detection limit of the chamber is 3.7x10 5 Bq/m 3 .

  5. Clinical effects of Angelica dahurica dressing on patients with I-II phase pressure sores.

    Science.gov (United States)

    Gong, Fen; Niu, Junzhi; Pei, Xing

    2016-11-02

    Angelica dahurica is a well-known traditional Chinese Medicine (TCM), while little information is available about its effects on pressure sores. We aimed to investigate the clinical effect of Angelica dahurica on patients with I-II phase pressure sores, as well as the underlying mechanism. Patients (n = 98) with phase I and phase II pressure sores were enrolled and randomly assigned to control and treated groups. In addition to holistic nursing, patients in the control group received compound clotrimazole cream, while patients in the treated group received continuous 4 weeks of external application of Angelica dahurica dressing. Therapeutic effect was recorded, along with the levels of interleukin-8 (IL-8), epidermal growth factor (EGF), transforming growth factor (TGF)-β, and vascular endothelial growth factor (VEGF). Besides, HaCaT cells were cultured with different concentrations of Angelica dahurica, and then cell viability, clone formation numbers, cell cycle, and levels of cyclin D1 and cyclin-dependent kinase (CDK) 2 were determined. The total effective rate in the treated group was significantly higher than in the control group. Levels of IL-8, EGF, TGF-β, and VEGF were statistically increased by Angelica dahurica. In addition, the cell viability and clone formation numbers were significantly upregulated by Angelica dahurica in a dose-dependent manner. Also, the percentage of cells in G0/G1 phase, and levels of cyclin D1 and CDK2 were significantly elevated. Our results suggest that Angelica dahurica may provide an effective clinical treatment for I-II phase pressure sores.

  6. Remedial Design/Remedial Action Work Plan for Operable Units 6-05 and 10-04, Phase III

    Energy Technology Data Exchange (ETDEWEB)

    R. P. Wells

    2006-09-19

    The remedial design/remedial action for Operable Unit 6-05 (Waste Area Group 6) and Operable Unit 10-04 (Waste Area Group 10) - collectively called Operable Unit 10-04 has been divided into four phases. Phase I consists of developing and implementing institutional controls at Operable Unit 10-04 sites and developing and implementing Idaho National Laboratory-wide plans for both institutional controls and ecological monitoring. Phase II will remediate sites contaminated with trinitrotoluene and Royal Demolition Explosive. Phase III will remediate lead contamination at a gun range, and Phase IV will remediate hazards from unexploded ordnance. This Phase III remedial Design/Remedial Action Work Plan addresses the remediation of lead-contaminated soils found at the Security Training Facility (STF)-02 Gun Range located at the Idaho National Laboratory. Remediation of the STF-02 Gun Range will include excavating contaminated soils; physically separating copper and lead for recycling; returning separated soils below the remediation goal to the site; stabilizing contaminated soils, as required, and disposing of the separated soils that exceed the remediation goal; encapsulating and disposing of creosote-contaminated railroad ties and power poles; removing and disposing of the wooden building and asphalt pads found at the STF-02 Gun Range; sampling and analyzing soil to determine the excavation requirements; and when the remediation goals have been met, backfilling and contouring excavated areas and revegetating the affected area.

  7. Unexpected Relationships and Inbreeding in HapMap Phase III Populations

    Science.gov (United States)

    Stevens, Eric L.; Baugher, Joseph D.; Shirley, Matthew D.; Frelin, Laurence P.; Pevsner, Jonathan

    2012-01-01

    Correct annotation of the genetic relationships between samples is essential for population genomic studies, which could be biased by errors or omissions. To this end, we used identity-by-state (IBS) and identity-by-descent (IBD) methods to assess genetic relatedness of individuals within HapMap phase III data. We analyzed data from 1,397 individuals across 11 ethnic populations. Our results support previous studies (Pemberton et al., 2010; Kyriazopoulou-Panagiotopoulou et al., 2011) assessing unknown relatedness present within this population. Additionally, we present evidence for 1,657 novel pairwise relationships across 9 populations. Surprisingly, significant Cotterman's coefficients of relatedness K1 (IBD1) values were detected between pairs of known parents. Furthermore, significant K2 (IBD2) values were detected in 32 previously annotated parent-child relationships. Consistent with a hypothesis of inbreeding, regions of homozygosity (ROH) were identified in the offspring of related parents, of which a subset overlapped those reported in previous studies (Gibson et al. 2010; Johnson et al. 2011). In total, we inferred 28 inbred individuals with ROH that overlapped areas of relatedness between the parents and/or IBD2 sharing at a different genomic locus between a child and a parent. Finally, 8 previously annotated parent-child relationships had unexpected K0 (IBD0) values (resulting from a chromosomal abnormality or genotype error), and 10 previously annotated second-degree relationships along with 38 other novel pairwise relationships had unexpected IBD2 (indicating two separate paths of recent ancestry). These newly described types of relatedness may impact the outcome of previous studies and should inform the design of future studies relying on the HapMap Phase III resource. PMID:23185369

  8. Stability considerations of permanent magnet quadrupoles for CESR phase-III upgrade

    Directory of Open Access Journals (Sweden)

    W. Lou

    1998-06-01

    Full Text Available The Cornell electron storage ring (CESR phase-III upgrade plan includes very strong permanent magnet quadrupoles in front of the cryostat for the superconducting quadrupoles and physically as close as possible to the interaction point. Together with the superconducting quadrupoles, they provide tighter vertical focusing at the interaction point. The quadrupoles are built with neodymium iron boron (NdFeB material and operate inside the 15 kG solenoid field. Requirements on the field quality and stability of these quadrupoles are discussed and test results are presented.

  9. Superior outcome of women with stage I/II cutaneous melanoma: Pooled analysis of four European organisation for research and treatment of cancer phase III trials

    NARCIS (Netherlands)

    A. Joosse (Arjen); S. Collette (Sandra); S. Suciu (Stefan); T.E.C. Nijsten (Tamar); F.J. Lejeune (Ferdy); U.R. Kleeberg (Ulrich); J.W.W. Coebergh (Jan Willem); A.M.M. Eggermont (Alexander); E.G.E. de Vries (Elisabeth)

    2012-01-01

    textabstractPurpose: Several studies observed a female advantage in the prognosis of cutaneous melanoma, for which behavioral factors or an underlying biologic mechanism might be responsible. Using complete and reliable follow-up data from four phase III trials of the European Organisation for

  10. DECOVALEX - Mathematical models of coupled T-H-M processes for nuclear waste repositories. Report of phase III

    International Nuclear Information System (INIS)

    Jing, L.; Rutqvist, J.; Stephansson, O.

    1995-12-01

    This report presents the methodologies and results of the field/laboratory experiments and mathematical modeling defined for the phase III of the project. Results from test cases 2-6 are given in separate chapters of the report (which have been indexed separately), and the last chapter discusses the lessons learned from the three phases of the DECOVALEX project

  11. An Application of Graphical Approach to Construct Multiple Testing Procedure in a Hypothetical Phase III Design

    Directory of Open Access Journals (Sweden)

    Naitee eTing

    2014-01-01

    Full Text Available Many multiple testing procedures (MTP have been developed in recent years. Among these new procedures, the graphical approach is flexible and easy to communicate with non-statisticians. A hypothetical Phase III clinical trial design is introduced in this manuscript to demonstrate how graphical approach can be applied in clinical product development. In this design, an active comparator is used. It is thought that this test drug under development could potentially be superior to this comparator. For comparison of efficacy, the primary endpoint is well established and widely accepted by regulatory agencies. However, an important secondary endpoint based on Phase II findings looks very promising. The target dose may have a good opportunity to deliver superiority to the comparator. Furthermore, a lower dose is included in case the target dose may demonstrate potential safety concerns. This Phase III study is designed as a non-inferiority trial with two doses, and two endpoints. This manuscript will illustrate how graphical approach is applied to this design in handling multiple testing issues.

  12. CSER 01-008 Canning of Thermally Stabilized Plutonium Oxide Powder in PFP Glovebox HC-21A

    International Nuclear Information System (INIS)

    ERICKSON, D.G.

    2001-01-01

    This document presents the analysis performed to support the canning operation in HC-21A. Most of the actual analysis was performed for the operation in HC-18M and HA-20MB, and is documented in HNF-2707 Rev I a (Erickson 2001a). This document will reference Erickson (2001a) as necessary to support the operation in HC-21A. The plutonium stabilization program at the Plutonium Finishing Plant (PFP) uses heat to convert plutonium-bearing materials into dry powder that is chemically stable for long term storage. The stabilized plutonium is transferred into one of several gloveboxes for the canning process, Gloveboxes HC-18M in Room 228'2, HA-20MB in Room 235B, and HC-21A in Room 230B are to be used for this process. This document presents the analysis performed to support the canning operation in HC-21A. Most of the actual analysis was performed for the operation in HC-I8M and HA-20MB, and is documented in HNF-2707 Rev l a (Erickson 2001a). This document will reference Erickson (2001a) as necessary to support the operation in HC-21A. Evaluation of this operation included normal, base cases, and contingencies. The base cases took the normal operations for each type of feed material and added the likely off-normal events. Each contingency is evaluated assuming the unlikely event happens to the conservative base case. Each contingency was shown to meet the double contingency requirement. That is, at least two unlikely, independent, and concurrent changes in process conditions are required before a criticality is possible

  13. Use of simulation to examine operational scenarios in a lathe glovebox for the processing of nuclear materials

    International Nuclear Information System (INIS)

    McQueen, M.; Ashok, P.; Cox, D.J.; Pittman, P.C.; Turner, C.J.; Hollen, R.M.

    2001-01-01

    In the process of dispositioning nuclear materials into storage, the use of a robot eliminates the safety risks to humans and increases productivity. The current process of processing typically uses humans to handle the hazardous material using gloves through glove-ports. This process is not only dangerous, but also costly, because humans can only be subjected to limited exposure to nuclear materials due to the actual Occupational Radiation Exposure (ORE) and thus have a fixed amount of dedicated workload per unit time. Use of robotics reduces ORE to humans and increases productivity. The Robotics Research Group at the University of Texas at Austin has created a simulation model of a conceptual application that uses a robot inside the glovebox to handle hazardous materials for lathe machining process operations in cooperation with Los Alamos National Laboratories (LANL). The actions of the robot include preparing the parts for entry into the box, weighing the parts, positioning the parts into the headstock chuck of the lathe, handling the subsequent processed parts, changing and replacing the lathe tools and chuck assemblies are necessary to process the material. The full three-dimensional geometric model of the simulation demonstrates the normal expected operation from beginning to end and verifies the path plans for the robot. The emphasis of this paper is to report additional findings from the simulation model, which is currently being expanded to include failure mode analysis, error recovery, and other what-if scenarios involved in unexpected, or unplanned, operation of the robot and lathe process inside of the glovebox.

  14. Conceptual design report for environmental, safety and health phase III FY-91 line item

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-09-01

    The Mound Facility (Mound), located in Miamisburg, Ohio, is a Department of Energy (DOE) development and production facility performing support work for DOE`s weapons and energy-related programs. EG&G Mound Applied Technologies (EG&G) is the Operating Contractor (OC) for this Government-Owned, Contractor-Operated (GOCO) facility. The work performed at Mound emphasizes nuclear energy and explosives technology. Mound is currently implementing an Environmental, Safety, and Health (ES&H) Program designed to protect its employees, the public, and the environment from adverse effects caused by the facility`s activities. Design has been completed, and construction is in progress for Phase I of this multiphase program. Phase II has been submitted for fiscal year (FY) 89 funding and Phase IV is being submitted as an FY 92 line item. This Conceptual Design Report (CDR) addresses Phase III of the ES&H program.

  15. Device Assembly Facility (DAF) Glovebox Radioactive Waste Characterization

    International Nuclear Information System (INIS)

    Dominick, J L

    2001-01-01

    The Device Assembly Facility (DAF) at the Nevada Test Site (NTS) provides programmatic support to the Joint Actinide Shock Physics Experimental Research (JASPER) Facility in the form of target assembly. The target assembly activities are performed in a glovebox at DAF and include Special Nuclear Material (SNM). Currently, only activities with transuranic SNM are anticipated. Preliminary discussions with facility personnel indicate that primarily two distributions of SNM will be used: Weapons Grade Plutonium (WG-Pu), and Pu-238 enhanced WG-Pu. Nominal radionuclide distributions for the two material types are included in attachment 1. Wastes generated inside glove boxes is expected to be Transuranic (TRU) Waste which will eventually be disposed of at the Waste Isolation Pilot Plant (WIPP). Wastes generated in the Radioactive Material Area (RMA), outside of the glove box is presumed to be low level waste (LLW) which is destined for disposal at the NTS. The process knowledge quantification methods identified herein may be applied to waste generated anywhere within or around the DAF and possibly JASPER as long as the fundamental waste stream boundaries are adhered to as outlined below. The method is suitable for quantification of waste which can be directly surveyed with the Blue Alpha meter or swiped. An additional quantification methodology which requires the use of a high resolution gamma spectroscopy unit is also included and relies on the predetermined radionuclide distribution and utilizes scaling to measured nuclides for quantification

  16. A new ion imprinted polymer based on Ru(III)-thiobarbituric acid complex for solid phase extraction of ruthenium(III) prior to its determination by ETAAS

    International Nuclear Information System (INIS)

    Zambrzycka, Elżbieta; Godlewska-Żyłkiewicz, Beata

    2014-01-01

    A new ruthenium ion imprinted polymer was prepared from the Ru(III) 2-thiobarbituric acid complex (the template), methacrylic acid or acrylamide (the functional monomers), and ethylene glycol dimethacrylate (the cross-linking agent) using 2,2′-azobisisobutyronitrile as the radical initiator. The ion imprinted polymer was characterized and used as a selective sorbent for the solid phase extraction of Ru(III) ions. The effects of type of functional monomer, sample volume, solution pH and flow rate on the extraction efficiency were studied in the dynamic mode. Ru(III) ion was quantitatively retained on the sorbents in the pH range from 3.5 to 10, and can be eluted with 4 mol L−1 aqueous ammonia. The affinity of Ru(III) for the ion imprinted polymer based on the acrylamide monomer is weaker than that for the polymer based on the methacrylic acid monomer, which therefore was used in interference studies and in analytical applications. Following extraction of Ru(III) ions with the imprint and their subsequent elution from the polymer with aqueous ammonia, Ru(III) was detected by electrothermal atomic absorption spectrometry with a detection limit of 0.21 ng mL −1 . The method was successfully applied to the determination of trace amounts of Ru(III) in water, waste, road dust and platinum ore (CRM SARM 76) with a reproducibility (expressed as RSD) below 6.4 %. (author)

  17. Optimal dose selection accounting for patient subpopulations in a randomized Phase II trial to maximize the success probability of a subsequent Phase III trial.

    Science.gov (United States)

    Takahashi, Fumihiro; Morita, Satoshi

    2018-02-08

    Phase II clinical trials are conducted to determine the optimal dose of the study drug for use in Phase III clinical trials while also balancing efficacy and safety. In conducting these trials, it may be important to consider subpopulations of patients grouped by background factors such as drug metabolism and kidney and liver function. Determining the optimal dose, as well as maximizing the effectiveness of the study drug by analyzing patient subpopulations, requires a complex decision-making process. In extreme cases, drug development has to be terminated due to inadequate efficacy or severe toxicity. Such a decision may be based on a particular subpopulation. We propose a Bayesian utility approach (BUART) to randomized Phase II clinical trials which uses a first-order bivariate normal dynamic linear model for efficacy and safety in order to determine the optimal dose and study population in a subsequent Phase III clinical trial. We carried out a simulation study under a wide range of clinical scenarios to evaluate the performance of the proposed method in comparison with a conventional method separately analyzing efficacy and safety in each patient population. The proposed method showed more favorable operating characteristics in determining the optimal population and dose.

  18. Pipe Overpack Container Fire Testing: Phase I II & III.

    Energy Technology Data Exchange (ETDEWEB)

    Figueroa, Victor G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ammerman, Douglas J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lopez, Carlos [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gill, Walter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-02-01

    The Pipe Overpack Container (POC) was developed at Rocky Flats to transport plutonium residues with higher levels of plutonium than standard transuranic (TRU) waste to the Waste Isolation Pilot Plant (WIPP) for disposal. In 1996 Sandia National Laboratories (SNL) conducted a series of tests to determine the degree of protection POCs provided during storage accident events. One of these tests exposed four of the POCs to a 30-minute engulfing pool fire, resulting in one of the 7A drum overpacks generating sufficient internal pressure to pop off its lid and expose the top of the pipe container (PC) to the fire environment. The initial contents of the POCs were inert materials, which would not generate large internal pressure within the PC if heated. POCs are now being used to store combustible TRU waste at Department of Energy (DOE) sites. At the request of DOE’s Office of Environmental Management (EM) and National Nuclear Security Administration (NNSA), starting in 2015 SNL conducted a series of fire tests to examine whether PCs with combustibles would reach a temperature that would result in (1) decomposition of inner contents and (2) subsequent generation of sufficient gas to cause the PC to over-pressurize and release its inner content. Tests conducted during 2015 and 2016 were done in three phases. The goal of the first phase was to see if the PC would reach high enough temperatures to decompose typical combustible materials inside the PC. The goal of the second test phase was to determine under what heating loads (i.e., incident heat fluxes) the 7A drum lid pops off from the POC drum. The goal of the third phase was to see if surrogate aerosol gets released from the PC when the drum lid is off. This report will describe the various tests conducted in phase I, II, and III, present preliminary results from these tests, and discuss implications for the POCs.

  19. Enantiomeric separation of iridium (III) complexes using HPLC chiral stationary phases based on amylose derivatives

    International Nuclear Information System (INIS)

    Kim, Hee Eun; Seo, Na Hyeon; Hyun, Myung Ho

    2016-01-01

    Cyclometalated iridium (III) complexes formed with three identical cyclometalating (C-N) ligands (homoleptic) or formed with two cyclometalating (C-N) ligands and one ancillary (LX) ligand (heteroleptic) have been known as highly phosphorescent materials and, thus, they have been utilized as efficient phosphorescent dopants in organic light emitting diodes (OLEDs) 1–3 or as effective phosphorescent chemosensors. 4–7 Cylometalated iridium (III) complexes are chiral compounds consisting of lambda (Λ, left-handed) and delta (Δ, right-handed) isomers. Racemic cyclometa- lated iridium (III) complexes emit light with no net polarization, but optically active cyclometalated iridium (III) complexes emit circularly polarized light. 8,9 Circularly polarized light can be used in various fields including highly efficient three dimensional electronic devices, photo nic devices for optical data storage, biological assays, and others. 8,9 In order to obtain optically active cylometalated iridium (III) complexes and to determine the enantiomeric composition of optically active cylometalated iridium (III) complexes, liquid chromatogr aphic enantiomer separation method on chiral stationary phases (CSPs) has been used. For example, Okamoto and coworkers first reported the high performance liquid chromatographic (HPLC) direct enantiomeric separation of two homoleptic cylometalated iridium (III) complexes on immobilized amylose tris(3,5- dimethylphenylcarbamate) (Chiralpak IA), coated cellulose tris(3,5-dimethylphenylcarbamate) (Chiralc el OD), and coated cellulose tris(4-methylbenzoate) (Chiralce l OJ). 10 Supercritical fluid chromatography (SFC) was also used by Bernhard and coworkers for the enantiomeric separation of cylometalated iridium (III) complexes on coated amylose tris(3,5-dimethylphenylcarbamate) (Chiralpak AD-H). 8 However, the general use of the HPLC method for the direct enantiomeric separation of homoleptic

  20. Enantiomeric separation of iridium (III) complexes using HPLC chiral stationary phases based on amylose derivatives

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hee Eun; Seo, Na Hyeon; Hyun, Myung Ho [Dept. of Chemistry and Chemistry Institute for Functional Materials, Pusan National University, Busan (Korea, Republic of)

    2016-12-15

    Cyclometalated iridium (III) complexes formed with three identical cyclometalating (C-N) ligands (homoleptic) or formed with two cyclometalating (C-N) ligands and one ancillary (LX) ligand (heteroleptic) have been known as highly phosphorescent materials and, thus, they have been utilized as efficient phosphorescent dopants in organic light emitting diodes (OLEDs) 1–3 or as effective phosphorescent chemosensors. 4–7 Cylometalated iridium (III) complexes are chiral compounds consisting of lambda (Λ, left-handed) and delta (Δ, right-handed) isomers. Racemic cyclometa- lated iridium (III) complexes emit light with no net polarization, but optically active cyclometalated iridium (III) complexes emit circularly polarized light. 8,9 Circularly polarized light can be used in various fields including highly efficient three dimensional electronic devices, photo nic devices for optical data storage, biological assays, and others. 8,9 In order to obtain optically active cylometalated iridium (III) complexes and to determine the enantiomeric composition of optically active cylometalated iridium (III) complexes, liquid chromatogr aphic enantiomer separation method on chiral stationary phases (CSPs) has been used. For example, Okamoto and coworkers first reported the high performance liquid chromatographic (HPLC) direct enantiomeric separation of two homoleptic cylometalated iridium (III) complexes on immobilized amylose tris(3,5- dimethylphenylcarbamate) (Chiralpak IA), coated cellulose tris(3,5-dimethylphenylcarbamate) (Chiralc el OD), and coated cellulose tris(4-methylbenzoate) (Chiralce l OJ). 10 Supercritical fluid chromatography (SFC) was also used by Bernhard and coworkers for the enantiomeric separation of cylometalated iridium (III) complexes on coated amylose tris(3,5-dimethylphenylcarbamate) (Chiralpak AD-H). 8 However, the general use of the HPLC method for the direct enantiomeric separation of homoleptic.

  1. Explorations of new phases in the Ga(III)/In(III)-Mo(VI)-Se(IV)/Te(IV)-O systems.

    Science.gov (United States)

    Kong, Fang; Hu, Chun-Li; Hu, Ting; Zhou, Yong; Mao, Jiang-Gao

    2009-07-07

    Systematic explorations of new phases in the Ga(III)/In(III)-Mo(VI)-Se(IV)/Te(IV)-O systems by hydrothermal syntheses or solid-state reactions at high-temperature led to four new quaternary compounds, namely, Ga(2)MoQ(2)O(10) (Q = Se, Te), In(2)Mo(2)Se(2)O(13)(H(2)O) and In(2)MoTe(2)O(10). Ga(2)MoQ(2)O(10) (Q = Se, Te) are isostructural and their structures feature a 3D network of gallium selenite/tellurite with 12-member ring tunnels along b-axis, the distorted MoO(6) octahedra are attached on the wall of the above tunnels. The structure of In(2)Mo(2)Se(2)O(13)(H(2)O) features a new pillared-layered architecture composed of 2D indium(III) selenite layers that are interconnected by Mo(2)O(10) dimers, forming 8-membered ring tunnels along the b-axis. The structure of In(2)MoTe(2)O(10) features a 2D indium oxide layer formed by corner- and edge-sharing InO(6) and InO(7) polyhedra with MoO(4) tetrahedra and TeO(n) (n = 4, 5) polyhedra hanging on both sides of the layer, there are weak interlayer Te-O bonds of 2.512 A. Results of optical diffuse reflectance spectrum measurements indicate that all four compounds are insulators, which are in agreement with results of band structure calculations based on DFT methods.

  2. Enginnering development of coal-fired high performance power systems phase II and III

    International Nuclear Information System (INIS)

    1998-01-01

    This report presents work carried out under contract DE-AC22-95PC95144 ''Engineering Development of Coal-Fired High Performance Systems Phase II and III.'' The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) that is capable of: thermal efficiency (HHV) >47%; NOx, SOx, and particulates 65% of heat input; all solid wastes benign; cost of electricity <90% of present plants. Phase I, which began in 1992, focused on the analysis of various configurations of indirectly fired cycles and on technical assessments of alternative plant subsystems and components, including performance requirements, developmental status, design options, complexity and reliability, and capital and operating costs. Phase I also included preliminary R ampersand D and the preparation of designs for HIPPS commercial plants approximately 300 MWe in size. This phase, Phase II, involves the development and testing of plant subsystems, refinement and updating of the HIPPS commercial plant design, and the site selection and engineering design of a HIPPS prototype plant. Work reported herein is from: Task 2.2 HITAF Air Heaters; Task 6 HIPPS Commercial Plant Design Update

  3. Integrated monitoring and surveillance system demonstration project: Phase I accomplishments

    International Nuclear Information System (INIS)

    Aumeier, S.E.; Walters, B.G.; Crawford, D.C.

    1997-01-01

    The authors present the results of the Integrated Monitoring and Surveillance System (IMSS) demonstration project Phase I efforts. The rationale behind IMSS development is reviewed and progress in each of the 5 basic tasks is detailed. Significant results include decisions to use Echelon LonWorks networking protocol and Microsoft Access for the data system needs, a preliminary design for the plutonium canning system glovebox, identification of facilities and materials available for the demonstration, determination of possibly affected facility documentation, and a preliminary list of available sensor technologies. Recently imposed changes in the overall project schedule and scope are also discussed and budgetary requirements for competition of Phase II presented. The results show that the IMSS demonstration project team has met and in many cases exceeded the commitments made for Phase I deliverables

  4. Phase II and III Clinical Studies of Diphtheria-Tetanus-Acellular Pertussis Vaccine Containing Inactivated Polio Vaccine Derived from Sabin Strains (DTaP-sIPV).

    Science.gov (United States)

    Okada, Kenji; Miyazaki, Chiaki; Kino, Yoichiro; Ozaki, Takao; Hirose, Mizuo; Ueda, Kohji

    2013-07-15

    Phase II and III clinical studies were conducted to evaluate immunogenicity and safety of a novel DTaP-IPV vaccine consisting of Sabin inactivated poliovirus vaccine (sIPV) and diphtheria-tetanus-acellular pertussis vaccine (DTaP). A Phase II study was conducted in 104 healthy infants using Formulation H of the DTaP-sIPV vaccine containing high-dose sIPV (3, 100, and 100 D-antigen units for types 1, 2, and 3, respectively), and Formulations M and L, containing half and one-fourth of the sIPV in Formulation H, respectively. Each formulation was administered 3 times for primary immunization and once for booster immunization. A Phase III study was conducted in 342 healthy infants who received either Formulation M + oral polio vaccine (OPV) placebo or DTaP + OPV. The OPV or OPV placebo was orally administered twice between primary and booster immunizations. Formulation M was selected as the optimum dose. In the Phase III study, the seropositive rate was 100% for all Sabin strains after primary immunization, and the neutralizing antibody titer after booster immunization was higher than in the control group (DTaP + OPV). All adverse reactions were clinically acceptable. DTaP-sIPV was shown to be a safe and immunogenic vaccine. JapicCTI-121902 for Phase II study, JapicCTI-101075 for Phase III study (http://www.clinicaltrials.jp/user/cte_main.jsp).

  5. Effects of PECS Phase III Application Training on Independent Mands in Young Children with Autism

    Science.gov (United States)

    Love, Jessica June

    2013-01-01

    The purpose of this study was to examine the effects of PECS phase III application training on independent mands in young children with autism. Participants were five children with autism ranging from ages 2 to 4 years old. A multiple baseline across participants was used to evaluate acquisition of independent correct mands across baseline and…

  6. Investor Outlook: Focus on Upcoming LCA2 Gene Therapy Phase III Results.

    Science.gov (United States)

    Schimmer, Joshua; Breazzano, Steven

    2015-09-01

    Investor interest in gene therapy has increased substantially over the past few years, and the next major catalyst for the field is likely to be Spark Therapeutics's phase III trial for the treatment of visual impairment caused by RPE65 gene mutations (often referred to as Leber congenital amaurosis type 2, or LCA2, but may include other retinal disorders). Analysis of the approach from the basic genetics, underlying visual mechanisms, clinical data, and commercialization considerations helps frame investor expectations and the potential implications for the broader field.

  7. Waste retrieval sluicing system vapor sampling and analysis plan for evaluation of organic emissions, process test phase III

    International Nuclear Information System (INIS)

    SASAKI, L.M.

    1999-01-01

    This sampling and analysis plan identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples obtained to address vapor issues related to the sluicing of tank 241-C-106. Sampling will be performed in accordance with Waste Retrieval Sluicing System Emissions Collection Phase III (Jones 1999) and Process Test Plan Phase III, Waste Retrieval Sluicing System Emissions Collection (Powers 1999). Analytical requirements include those specified in Request for Ecology Concurrence on Draft Strategy/Path Forward to Address Concerns Regarding Organic Emissions from C-106 Sluicing Activities (Peterson 1998). The Waste Retrieval Sluicing System was installed to retrieve and transfer high-heat sludge from tank 241-C-106 to tank 241-AY-102, which is designed for high-heat waste storage. During initial sluicing of tank 241-C-106 in November 1998, operations were halted due to detection of unexpected high volatile organic compounds in emissions that exceeded regulatory permit limits. Several workers also reported smelling sharp odors and throat irritation. Vapor grab samples from the 296-C-006 ventilation system were taken as soon as possible after detection; the analyses indicated that volatile and semi-volatile organic compounds were present. In December 1998, a process test (phase I) was conducted in which the pumps in tanks 241-C-106 and 241-AY-102 were operated and vapor samples obtained to determine constituents that may be present during active sluicing of tank 241-C-106. The process test was suspended when a jumper leak was detected. On March 7, 1999, phase I1 of the process test was performed; the sluicing system was operated for approximately 7 hours and was ended using the controlled shutdown method when the allowable amount of solids were transferred to 241-AY-102. The phase II test was successful, however, further testing is required to obtain vapor samples at higher emission levels

  8. SPSP Phase III Recruiting, Selecting, and Developing Secure Power Systems Professionals. Individual and Team Performance Guidelines

    Energy Technology Data Exchange (ETDEWEB)

    O' Neil, Lori Ross [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Conway, T. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tobey, D. H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Greitzer, Frank L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Dalton, Angela C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pusey, Portia K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-03-01

    The Secure Power Systems Professional Phase III final report was released last year which an appendix of Individual and Team Performance Guidelines. This new report is that appendix broken out as a standalone document to assist utilities in recruiting and developing Secure Power Systems Professionals at their site.

  9. Comparison between publicly accessible publications, registries, and protocols of phase III trials indicated persistence of selective outcome reporting.

    Science.gov (United States)

    Zhang, Sheng; Liang, Fei; Li, Wenfeng

    2017-11-01

    The decision to make protocols of phase III randomized controlled trials (RCTs) publicly accessible by leading journals was a landmark event in clinical trial reporting. Here, we compared primary outcomes defined in protocols with those in publications describing the trials and in trial registration. We identified phase III RCTs published between January 1, 2012, and June 30, 2015, in The New England Journal of Medicine, The Lancet, The Journal of the American Medical Association, and The BMJ with available protocols. Consistency in primary outcomes between protocols and registries (articles) was evaluated. We identified 299 phase III RCTs with available protocols in this analysis. Out of them, 25 trials (8.4%) had some discrepancy for primary outcomes between publications and protocols. Types of discrepancies included protocol-defined primary outcome reported as nonprimary outcome in publication (11 trials, 3.7%), protocol-defined primary outcome omitted in publication (10 trials, 3.3%), new primary outcome introduced in publication (8 trials, 2.7%), protocol-defined nonprimary outcome reported as primary outcome in publication (4 trials, 1.3%), and different timing of assessment of primary outcome (4 trials, 1.3%). Out of trials with discrepancies in primary outcome, 15 trials (60.0%) had discrepancies that favored statistically significant results. Registration could be seen as a valid surrogate of protocol in 237 of 299 trials (79.3%) with regard to primary outcome. Despite unrestricted public access to protocols, selective outcome reporting persists in a small fraction of phase III RCTs. Only studies from four leading journals were included, which may cause selection bias and limit the generalizability of this finding. Copyright © 2017 Elsevier Inc. All rights reserved.

  10. Phase II and III the next generation of CLS beamline control and data acquisition systems

    International Nuclear Information System (INIS)

    Matias, E.; Beauregard, D.; Berg, R.; Black, G.; Boots, M.J.; Dolton, W.; Hunter, D.; Igarashi, R.; Liu, D.; Maxwell, D.; Miller, C.D.; Wilson, T.; Wright, G.

    2012-01-01

    The Canadian Light Source (CLS) is nearing the completion of its suite of Phase II Beamlines and in detailed design of its Phase III Beamlines. The paper presents an overview of the overall approach adopted by CLS in the development of beamline control and data acquisition systems. Building on the experience of our first phase of beamlines the CLS has continued to make extensive use of EPICS with EDM and QT based user interfaces. Increasing interpretive languages such as Python are finding a place in the beamline control systems. Web based environment such as ScienceStudio have also found a prominent place in the control system architecture as we move to tighter integration between data acquisition, visualization and data analysis. (authors)

  11. Novel solid phase extraction procedure for gold(III) on Dowex M 4195 prior to its flame atomic absorption spectrometric determination

    International Nuclear Information System (INIS)

    Tuzen, Mustafa; Saygi, Kadriye O.; Soylak, Mustafa

    2008-01-01

    A method for solid phase extraction (SPE) of gold(III) using Dowex M 4195 chelating resin has been developed. The optimum experimental conditions for the quantitative sorption of gold(III), pH, effect of flow rates, eluent types, sorption capacity and the effect of diverse ions on the sorption of gold(III) have been investigated. The chelating resin can be reused for more than 100 cycles of sorption-desorption without any significant change in sorption of gold(III) ions. The recovery values for gold(III) and detection limit (LOD) of gold were greater than 95% and 1.61 μg L -1 , respectively. The preconcentration factor was 31. The relative standard deviation of the method was -1 . The proposed method has been applied for the determination of gold(III) in some real samples including water, soil and sediment samples

  12. Prediction of dose and field mapping around a shielded plutonium fuel fabrication glovebox

    International Nuclear Information System (INIS)

    Strode, J.N.; Soldat, K.L.; Brackenbush, L.W.

    1984-01-01

    Westinghouse Hanford Company, as the Department of Energy's (DOE) prime contractor for the operation of the Hanford Engineering Development Laboratory (HEDL), is responsible for the development of the Secure Automated Fabrication (SAF) Line which is to be installed in the recently constructed Fuels and Materials Examination Facility (FMEF). The SAF Line will fabricate mixed-oxide (MOX) fuel pins for the Fast Flux Test Facility (FFTF) at an annual throughput rate of six (6) metric tons (MT) of MOX. The SAF Line will also demonstrate the automated manufacture of fuel pins on a production-scale. This paper describes some of the techniques used to reduce personnel exposure on the SAF Line, as well as the prediction and field mapping of doses from a shielded fuel fabrication glovebox. Tables are also presented from which exposure rate estimates can be made for plutonium recovered from fuels having different isotopic compositions as a result of varied burnup

  13. Evaluation of candidate magnetohydrodynamic materials for the U-02 Phase III test

    International Nuclear Information System (INIS)

    Marchant, D.D.; Bates, J.L.

    1978-06-01

    As part of a cooperative U.S.--U.S.S.R. program, electrode and insulator materials tested at the Westinghouse Electrode Systems Test Facility in Pittsburgh, Pennsylvania, were evaluated. From this evaluation materials will be selected for use in the third phase of tests being conducted in the U-02 magnetohydrodynamics test facility in the Soviet Union. Electrode and insulator materials were examined with both an optical microscope and a scanning electron microscope. The cathodes were found to behave differently from the anodes; most notably, the cathodes showed greater potassium interaction. The lanthanum chromite-based electrodes (excluding those fabricated by plasma-spraying) are recommended for testing in the U-02 Phase III test. Hotpressed, fused-grained MgO and sintered MgAl 2 O 4 are recommended as insulator materials. The electrode attachment techniques used in the Westinghouse Tests were inadequate and need to be modified for the U-02 test

  14. Investigation of the separation of americium(III) and europium(III) by high-speed countercurrent chromatography

    International Nuclear Information System (INIS)

    Wu, J.F.; Jin, Y.R.; Xu, Q.C.; Wang, S.L.; Zhang, L.X.

    2005-01-01

    The long-lived actinides are the important elements in the radioactive waste ;disposal. Because the ions semi diameter and chemical properties of trivalent actinides(III) and trivalent lanthanides(III) are very similar, the separation between them is very difficult. Yang Yu-Sheng put forward the actinides(III) are softer acid than the lanthanides(III), so the actinides(III) are more easily extracted by the soft extractant contain sulfur or nitrogen than the lanthanides(III). Some research have been done on the separation between actinides(III) and lanthanides(III) using the extractants contain sulfur or nitrogen. The results show that satisfactory separation efficiency was gained. Countercurrent Chromatography (CCC) have many specific advantages, such as free from solid support, permit large sample volume and high flow rate, which is useful in the preconcentration of inorganic solute and inorganic preparation. Some studies were done on the separation of lanthanides or-other inorganic elements by HSCCC, the high-purity reagents prepared by HSCCC or CPC turned out to be successful. In present paper, the investigation of separation between Americium (III) and Euricium (III) by High-Speed Countercurrent Chromatography (HSCCC) were made. The extractant used in the work was prepared by ourselves, which is of the soft extractant contrain sulfur. The effects of separation condition on the separation efficiency of Am and Eu by HSCCC were investigated using dichlorophenyl dithiophosphinic acid in xylene as the stationary phase and 0.1 mol/L NaClO4 as mobile phase, respectively. The results show that mutual separation between Am and Eu can be accomplished. The separation factor increases with the increasing of the concentration of extractant and the pH value of the mobile phase, further more, minishing the flow rate of the mobile phase can also improves the separation efficiency between Am and Eu. The nearly base separation was gained when the flow rate is 0.35 ml/min, the

  15. Gene expression of transporters and phase I/II metabolic enzymes in murine small intestine during fasting

    Directory of Open Access Journals (Sweden)

    van der Meijde Jolanda

    2007-08-01

    Full Text Available Abstract Background Fasting has dramatic effects on small intestinal transport function. However, little is known on expression of intestinal transport and phase I/II metabolism genes during fasting and the role the fatty acid-activated transcription factor PPARα may play herein. We therefore investigated the effects of fasting on expression of these genes using Affymetrix GeneChip MOE430A arrays and quantitative RT-PCR. Results After 24 hours of fasting, expression levels of 33 of the 253 analyzed transporter and phase I/II metabolism genes were changed. Upregulated genes were involved in transport of energy-yielding molecules in processes such as glycogenolysis (G6pt1 and mitochondrial and peroxisomal oxidation of fatty acids (Cact, Mrs3/4, Fatp2, Cyp4a10, Cyp4b1. Other induced genes were responsible for the inactivation of the neurotransmitter serotonin (Sert, Sult1d1, Dtd, Papst2, formation of eicosanoids (Cyp2j6, Cyp4a10, Cyp4b1, or for secretion of cholesterol (Abca1 and Abcg8. Cyp3a11, typically known because of its drug metabolizing capacity, was also increased. Fasting had no pronounced effect on expression of phase II metabolic enzymes, except for glutathione S-transferases which were down-regulated. Time course studies revealed that some genes were acutely regulated, whereas expression of other genes was only affected after prolonged fasting. Finally, we identified 8 genes that were PPARα-dependently upregulated upon fasting. Conclusion We have characterized the response to fasting on expression of transporters and phase I/II metabolic enzymes in murine small intestine. Differentially expressed genes are involved in a variety of processes, which functionally can be summarized as a increased oxidation of fat and xenobiotics, b increased cholesterol secretion, c increased susceptibility to electrophilic stressors, and d reduced intestinal motility. This knowledge increases our understanding of gut physiology, and may be of relevance

  16. Evaluation of Life Sciences Glovebox (LSG) and Multi-Purpose Crew Restraint Concepts

    Science.gov (United States)

    Whitmore, Mihriban

    2005-01-01

    Within the scope of the Multi-purpose Crew Restraints for Long Duration Spaceflights project, funded by Code U, it was proposed to conduct a series of evaluations on the ground and on the KC-135 to investigate the human factors issues concerning confined/unique workstations, such as the design of crew restraints. The usability of multiple crew restraints was evaluated for use with the Life Sciences Glovebox (LSG) and for performing general purpose tasks. The purpose of the KC-135 microgravity evaluation was to: (1) to investigate the usability and effectiveness of the concepts developed, (2) to gather recommendations for further development of the concepts, and (3) to verify the validity of the existing requirements. Some designs had already been tested during a March KC-135 evaluation, and testing revealed the need for modifications/enhancements. This flight was designed to test the new iterations, as well as some new concepts. This flight also involved higher fidelity tasks in the LSG, and the addition of load cells on the gloveports.

  17. Baseline job satisfaction and stress among pharmacists and pharmacy technicians participating in the Fleetwood Phase III Study.

    Science.gov (United States)

    Lapane, Kate L; Hughes, Carmel M

    2004-11-01

    To provide baseline levels of job satisfaction and stress among members of the long-term care pharmacy team participating in the Fleetwood Phase III evaluation. Cross-sectional design; long-term care pharmacy provider in North Carolina (the implementation site of the large-scale Fleetwood Phase III study). All current pharmacy employees as of May/June 2002. None. Health Professional Stress Inventory and job satisfaction. Ninety-four percent (16/17) of consultant pharmacists were satisfied with their job, with 89% reporting they would definitely choose to be a pharmacist again. Seventy-five percent both of dispensing pharmacists and pharmacy technicians reported overall job satisfaction. Forty-one reported that they would not choose to be a pharmacist (pharmacy technician) again. The most frequently reported sources of stress among the dispensing pharmacists and pharmacy technicians were conflicts with non-work obligations (i.e., family, personal life) and the ability to perform duties with short staffing. In addition, inadequate pay and few opportunities for job advancement were often/frequent sources of stress among pharmacy technicians. More than one third of dispensing pharmacists also reported stress frequently because of fears of mistakes in patient treatment. Overall, consultants are very satisfied with their positions, although dispensing pharmacists and pharmacy technicians are less satisfied with their work. The reasons may be because of the different nature of each job, as well as staffing shortages. The extent to which the Fleetwood Model can improve job satisfaction and impact on stress will be evaluated once we resurvey the pharmacy team after the intervention period of the Fleetwood Phase III study.

  18. Development of a central data warehouse for statewide ITS and transportation data in Florida phase III : final report.

    Science.gov (United States)

    2009-12-15

    This report documents Phase III of the development and operation of a prototype for the Statewide Transportation : Engineering Warehouse for Archived Regional Data (STEWARD). It reflects the progress on the development and : operation of STEWARD sinc...

  19. Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

    International Nuclear Information System (INIS)

    Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E.

    2014-01-01

    Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH) 3 ·3H 2 O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH) 3 (am) was stable with a solubility lower than 50 μg/l in the range 5.7 0.75 Cr 0.25 (OH) 3 , the stability region was extended to 4.8 3 ·xH 2 O whereas in the presence of iron the precipitate is a mixed Fe (1−x) Cr x (OH) 3 phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe x ,Cr 1−x )(OH) 3 hydroxides as compared to the stability of Cr(OH) 3 . We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH) 3 ·3H 2 O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH) 3 (am) phase. Mixed Fe 0.75 Cr 0.25 (OH) 3 hydroxides were found to be of the ferrihydrite structure, Fe(OH) 3 , and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III) hydroxides are more effective enhancers of groundwater quality, in comparison to the plain amorphous or crystalline Cr(III) hydroxides, the latter found to have a solubility typically higher than 50 μg/l (maximum EU permitted Cr level in drinking water), while the amorphous Cr(OH) 3 (am) phase was within the drinking water threshold in the range 5.7 0.75 Cr 0.25 (OH) 3 hydroxides studied were of extended stability in the 4.8 < pH < 13.5 range

  20. Lapatinib versus hormone therapy in patients with advanced renal cell carcinoma: a randomized phase III clinical trial

    DEFF Research Database (Denmark)

    Ravaud, Alain; Hawkins, Robert; Gardner, Jason P

    2008-01-01

    PURPOSE: Lapatinib is an orally reversible inhibitor of epidermal growth factor receptor (EGFR)/human epidermal growth factor receptor 2 (HER-2) tyrosine kinases with demonstrated activity in patients with HER-2-positive breast cancer. In the current phase III open-label trial, lapatinib was comp...

  1. Twenty-seven years of phase III trials for patients with extensive disease small-cell lung cancer: disappointing results.

    Directory of Open Access Journals (Sweden)

    Isao Oze

    Full Text Available BACKGROUND: Few studies have formally assessed whether treatment outcomes have improved substantially over the years for patients with extensive disease small-cell lung cancer (ED-SCLC enrolled in phase III trials. The objective of the current investigation was to determine the time trends in outcomes for the patients in those trials. METHODS AND FINDINGS: We searched for trials that were reported between January 1981 and August 2008. Phase III randomized controlled trials were eligible if they compared first-line, systemic chemotherapy for ED-SCLC. Data were evaluated by using a linear regression analysis. RESULTS: In total, 52 trials were identified that had been initiated between 1980 and 2006; these studies involved 10,262 patients with 110 chemotherapy arms. The number of randomized patients and the proportion of patients with good performance status (PS increased over time. Cisplatin-based regimens, especially cisplatin and etoposide (PE regimen, have increasingly been studied, whereas cyclophosphamide, doxorubicin, and vincristine-based regimens have been less investigated. Multiple regression analysis showed no significant improvement in survival over the years. Additionally, the use of a PE regimen did not affect survival, whereas the proportion of patients with good PS and the trial design of assigning prophylactic cranial irradiation were significantly associated with favorable outcome. CONCLUSIONS AND SIGNIFICANCE: The survival of patients with ED-SCLC enrolled in phase III trials did not improve significantly over the years, suggesting the need for further development of novel targets, newer agents, and comprehensive patient care.

  2. 200-ZP-1 phase II and III IRM groundwater pump and treat site safety plan

    International Nuclear Information System (INIS)

    St. John, C.H.

    1996-07-01

    This safety plan covers operations, maintenance, and support activities related to the 200-ZP-1 Phase II and III Ground Water Pump- and-Treat Facility. The purpose of the facility is to extract carbon tetrachloride contaminated groundwater underlying the ZP-1 Operable Unit; separate the contaminant from the groundwater; and reintroduce the treated water to the aquifer. An air stripping methodology is employed to convert volatile organics to a vapor phase for absorption onto granular activated carbon. The automated process incorporates a variety of process and safety features that shut down the process system in the event that process or safety parameters are exceeded or compromised

  3. Synthesis, characterization and stability of Cr(III) and Fe(III) hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Papassiopi, N.; Vaxevanidou, K.; Christou, C.; Karagianni, E.; Antipas, G.S.E., E-mail: gantipas@metal.ntua.gr

    2014-01-15

    Highlights: • Fe(III)–Cr(III) hydroxides enhance groundwater quality better than pure Cr(III) compounds. • Crystalline Cr(OH){sub 3}·3H{sub 2}O was unstable, with a solubility higher than 50 μg/l. • Amorphous Cr(OH){sub 3}(am) was stable with a solubility lower than 50 μg/l in the range 5.7 < pH < 11. • For mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3}, the stability region was extended to 4.8 < pH < 13.5. -- Abstract: Chromium is a common contaminant of soils and aquifers and constitutes a major environmental problem. In nature, chromium usually exists in the form of two oxidation states, trivalent, Cr(III), which is relatively innocuous for biota and for the aquatic environment, and hexavalent, Cr(VI) which is toxic, carcinogenic and very soluble. Accordingly, the majority of wastewater and groundwater treatment technologies, include a stage where Cr(VI) is reduced to Cr(III), in order to remove chromium from the aqueous phase and bind the element in the form of environmentally stable solid compounds. In the absence of iron the final product is typically of the form Cr(OH){sub 3}·xH{sub 2}O whereas in the presence of iron the precipitate is a mixed Fe{sub (1−x)}Cr{sub x}(OH){sub 3} phase. In this study, we report on the synthesis, characterisation and stability of mixed (Fe{sub x},Cr{sub 1−x})(OH){sub 3} hydroxides as compared to the stability of Cr(OH){sub 3}. We established that the plain Cr(III) hydroxide, abiding to the approximate molecular formula Cr(OH){sub 3}·3H{sub 2}O, was crystalline, highly soluble, i.e. unstable, with a tendency to transform into the stable amorphous hydroxide Cr(OH){sub 3}(am) phase. Mixed Fe{sub 0.75}Cr{sub 0.25}(OH){sub 3} hydroxides were found to be of the ferrihydrite structure, Fe(OH){sub 3}, and we correlated their solubility to that of a solid solution formed by plain ferrihydrite and the amorphous Cr(III) hydroxide. Both our experimental results and thermodynamic calculations indicated that mixed Fe(III)–Cr(III

  4. Classification of criticality calculations with correlation coefficient method and its application to OECD/NEA burnup credit benchmarks phase III-A and II-A

    International Nuclear Information System (INIS)

    Okuno, Hiroshi

    2003-01-01

    A method for classifying benchmark results of criticality calculations according to similarity was proposed in this paper. After formulation of the method utilizing correlation coefficients, it was applied to burnup credit criticality benchmarks Phase III-A and II-A, which were conducted by the Expert Group on Burnup Credit Criticality Safety under auspices of the Nuclear Energy Agency of the Organisation for Economic Cooperation and Development (OECD/NEA). Phase III-A benchmark was a series of criticality calculations for irradiated Boiling Water Reactor (BWR) fuel assemblies, whereas Phase II-A benchmark was a suite of criticality calculations for irradiated Pressurized Water Reactor (PWR) fuel pins. These benchmark problems and their results were summarized. The correlation coefficients were calculated and sets of benchmark calculation results were classified according to the criterion that the values of the correlation coefficients were no less than 0.15 for Phase III-A and 0.10 for Phase II-A benchmarks. When a couple of benchmark calculation results belonged to the same group, one calculation result was found predictable from the other. An example was shown for each of the Benchmarks. While the evaluated nuclear data seemed the main factor for the classification, further investigations were required for finding other factors. (author)

  5. SPSP Phase III Recruiting, Selecting, and Developing Secure Power Systems Professionals: Behavioral Interview Guidelines by Job Roles

    Energy Technology Data Exchange (ETDEWEB)

    O' Neil, Lori Ross [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Conway, T. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tobey, D. H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Greitzer, Frank L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Dalton, Angela C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pusey, Portia K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-03-01

    The Secure Power Systems Professional Phase III final report was released last year which an appendix of Behavioral Interview Guidelines by Job Roles. This new report is that appendix broken out as a standalone document to assist utilities in recruiting and developing Secure Power Systems Professionals at their site.

  6. Novel solid phase extraction procedure for gold(III) on Dowex M 4195 prior to its flame atomic absorption spectrometric determination

    Energy Technology Data Exchange (ETDEWEB)

    Tuzen, Mustafa [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey)], E-mail: mtuzen@gop.edu.tr; Saygi, Kadriye O. [Gaziosmanpasa University, Faculty of Science and Arts, Chemistry Department, 60250 Tokat (Turkey); Soylak, Mustafa [Erciyes University, Faculty of Science and Arts, Chemistry Department, 38039 Kayseri (Turkey)

    2008-08-15

    A method for solid phase extraction (SPE) of gold(III) using Dowex M 4195 chelating resin has been developed. The optimum experimental conditions for the quantitative sorption of gold(III), pH, effect of flow rates, eluent types, sorption capacity and the effect of diverse ions on the sorption of gold(III) have been investigated. The chelating resin can be reused for more than 100 cycles of sorption-desorption without any significant change in sorption of gold(III) ions. The recovery values for gold(III) and detection limit (LOD) of gold were greater than 95% and 1.61 {mu}g L{sup -1}, respectively. The preconcentration factor was 31. The relative standard deviation of the method was <5%. The adsorption capacity of the resin was 8.1 mg g{sup -1}. The proposed method has been applied for the determination of gold(III) in some real samples including water, soil and sediment samples.

  7. EXPERIMENTAL RESULTS OF THE NEPHELINE PHASE III STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K.; Edwards, T.

    2009-11-09

    This study is the third phase in a series of experiments designed to reduce conservatism in the model that predicts the formation of nepheline, a crystalline phase that can reduce the durability of high level waste glass. A Phase I study developed a series of glass compositions that were very durable while their nepheline discriminator values were well below the current nepheline discriminator limit of 0.62, where nepheline is predicted to crystallize upon slow cooling. A Phase II study selected glass compositions to identify any linear effects of composition on nepheline crystallization and that were restricted to regions that fell within the validation ranges of the Defense Waste Processing Facility (DWPF) Product Composition Control System (PCCS) models. However, it was not possible to identify any linear effects of composition on chemical durability performance for this set of study glasses. The results of the Phase II study alone were not sufficient to recommend modification of the current nepheline discriminator. It was recommended that the next series of experiments continue to focus not only on compositional regions where the PCCS models are considered applicable (i.e., the model validation ranges), but also be restricted to compositional regions where the only constraint limiting processing is the current nepheline discriminator. Two methods were used in selecting glasses for this Phase III nepheline study. The first was based on the relationship of the current nepheline discriminator model to the other DWPF PCCS models, and the second was based on theory of crystallization in mineral and glass melts. A series of 29 test glass compositions was selected for this study using a combination of the two approaches. The glasses were fabricated and characterized in the laboratory. After reviewing the data, the study glasses generally met the target compositions with little issue. Product Consistency Test results correlated well with the crystallization analyses in

  8. Phase III Advanced Anodes and Cathodes Utilized in Energy Efficient Aluminum Production Cells; FINAL

    International Nuclear Information System (INIS)

    Christini, R.A.; Dawless, R.K.; Ray, S.P.; Weirauch, D.A. Jr.

    2001-01-01

    During Phase I of the present program, Alcoa developed a commercial cell concept that has been estimated to save 30% of the energy required for aluminum smelting. Phase ii involved the construction of a pilot facility and operation of two pilots. Phase iii of the Advanced Anodes and Cathodes Program was aimed at bench experiments to permit the resolution of certain questions to be followed by three pilot cells. All of the milestones related to materials, in particular metal purity, were attained with distinct improvements over work in previous phases of the program. NiO additions to the ceramic phase and Ag additions to the Cu metal phase of the cermet improved corrosion resistance sufficiently that the bench scale pencil anodes met the purity milestones. Some excellent metal purity results have been obtained with anodes of the following composition: Further improvements in anode material composition appear to be dependent on a better understanding of oxide solubilities in molten cryolite. For that reason, work was commissioned with an outside consultant to model the MeO - cryolite systems. That work has led to a better understanding of which oxides can be used to substitute into the NiO-Fe2O3 ceramic phase to stabilize the ferrites and reduce their solubility in molten cryolite. An extensive number of vertical plate bench electrolysis cells were run to try to find conditions where high current efficiencies could be attained. TiB2-G plates were very inconsistent and led to poor wetting and drainage. Pure TiB2 did produce good current efficiencies at small overlaps (shadowing) between the anodes and cathodes. This bench work with vertical plate anodes and cathodes reinforced the importance of good cathode wetting to attain high current efficiencies. Because of those conclusions, new wetting work was commissioned and became a major component of the research during the third year of Phase III. While significant progress was made in several areas, much work needs to be

  9. Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in TEHDGA-HDEHP impregnated resins

    Energy Technology Data Exchange (ETDEWEB)

    Saipriya, G.; Kumar, T. [Bhabha Atomic Research Centre Facilities, Kalpakkam (India). Kalpakkam Reprocessing Plant; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2016-07-01

    The extraction behaviour of Am(III) and Eu(III) from nitric acid medium was studied in the solvent impregnated resins containing extractants such as tetra-bis(2-ethylhexyl)diglycolamide (TEHDGA) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of TEHDGA+HDEHP. The rate of extraction of Am(III) and Eu(III) from 1 M nitric acid and the effect of various parameters, such as the concentration of nitric acid in aqueous phase and concentration of TEHDGA and HDEHP in resin phase, on the distribution coefficient of Am(III) and Eu(III) was studied. The distribution coefficient of Am(III) and Eu(III) in HDEHP-impregnated resin decreased and that in TEHDGA-impregnated resin increased, with increase in the concentration of nitric acid. However, in (TEHDGA+HDEHP) - impregnated resin, synergic extraction was observed at lower nitric acid concentration and antagonism at higher nitric acid concentration. The mechanism of Am(III) and Eu(III) extraction in the combined resin was investigated by slope analysis method. The extraction of various metal ions present in the fast reactor simulated high-level liquid waste was studied. The separation factor of Am(III) over Eu(III) was studied using citrate-buffered diethylenetriaminepentaacetic acid (DTPA) solution.

  10. Neutral bidentate N-heterocyclic ligands - phase transfer reagents improving the kinetics of solvent extraction of Am(III) and Eu(III) ions with tetradentate 6,6'-bis-(diethyl-1,2,4-triazin-3-yl)-2,2'-bipyridine

    International Nuclear Information System (INIS)

    Narbutt, J.; Krejzler, J.

    2008-01-01

    Poor kinetics of solvent extraction of Am(III) and Eu(III) ions from 1 M HNO 3 with 6,6'-bis-(diethyl-1,2,4-triazin-3-yl)-2,2'-bipyridine (etBTBP) has been improved by adding an auxiliary bidentate N-heterocyclic ligand to the extraction system. Two such ligands were studied, derivatives of bis-triazine and pyridine-triazine, which alone poorly extract the metal ions, but together with etBTBP they act as phase transfer reagents, improving the extraction kinetics to a different degree. The ability to transfer the metal ions from aqueous to organic phase depends on lipophilicity and acid/base properties of these auxiliary ligands, as well as on the mode of shaking the two liquid phases - gentle or vigorous. (orig.)

  11. Broadband microwave photonic fully tunable filter using a single heterogeneously integrated III-V/SOI-microdisk-based phase shifter.

    Science.gov (United States)

    Lloret, Juan; Morthier, Geert; Ramos, Francisco; Sales, Salvador; Van Thourhout, Dries; Spuesens, Thijs; Olivier, Nicolas; Fédéli, Jean-Marc; Capmany, José

    2012-05-07

    A broadband microwave photonic phase shifter based on a single III-V microdisk resonator heterogeneously integrated on and coupled to a nanophotonic silicon-on-insulator waveguide is reported. The phase shift tunability is accomplished by modifying the effective index through carrier injection. A comprehensive semi-analytical model aiming at predicting its behavior is formulated and confirmed by measurements. Quasi-linear and continuously tunable 2π phase shifts at radiofrequencies greater than 18 GHz are experimentally demonstrated. The phase shifter performance is also evaluated when used as a key element in tunable filtering schemes. Distortion-free and wideband filtering responses with a tuning range of ~100% over the free spectral range are obtained.

  12. Extraction and separation studies of Ga(III, In(III and Tl(III using the neutral organophosphorous extractant, Cyanex-923

    Directory of Open Access Journals (Sweden)

    P. M. DHADKE

    2003-07-01

    Full Text Available The neutral extractant, Cyanes-923 has been used for the extraction and separation of gallium(III, indium(III and thallium(III from acidic solution. These metal ions were found to be quantitatively extracted with Cyanex-923 in toluene in the pH range 4.5–5.5, 5.0–6.5 and 1.5–3.0, respectively, and from the organic phase they can be stripped with 2.0 mol dm-3 HNO3, 3.0 mol dm-3 HNO3 and 3.0 mol dm-3 HCl, respectively. The effect of pH equilibration period, diluents, diverse ions and stripping agents on the extraction of Ga(III, In(III and Tl(III has been studied. The stroichiometry of the extracted species of these metal ions was determined on the basis of the slope analysis method. The reaction proceed by solvation and the probable extracted species found were [MCl3. 3Cyanex-923] [where M = Ga(III or In(III ] and [HTlCl4. 3Cyanex-923]. Based on these results a sequential procedure for the separation of Ga(III, In(III and Tl(III from each other was developed.

  13. Phase III trial of high- vs. low-dose-rate interstitial radiotherapy for early mobile tongue cancer

    International Nuclear Information System (INIS)

    Inoue, Takehiro; Inoue, Toshihiko; Yoshida, Ken; Yoshioka, Yasuo; Shimamoto, Shigetoshi; Tanaka, Eiichi; Yamazaki, Hideya; Shimizutani, Kimishige; Teshima, Teruki; Furukawa, Souhei

    2001-01-01

    Purpose: Early mobile tongue cancer can be controlled with interstitial radiotherapy (ISRT). We carried out a Phase III trial to compare the treatment results of low-dose-rate (Ld) ISRT and high-dose-rate (HDR) ISRT for early mobile tongue cancer. Methods and Materials: From April 1992 through October 1996, 59 patients with cancer of the early mobile tongue were registered in this Phase III study. Eight patients were excluded from the evaluation because of violations of the requirements for this study. Of 51 eligible patients, 26 patients were treated with LDR-ISRT (70 Gy/4-9 days) and 25 patients with HDR-ISRT (60 Gy/10 fractions/1 week). For the hyperfractionated HDR-ISRT, the time interval between 2 fractions was more than 6 h. Results: Five-year local control rates of the LDR and HDR groups were 84% and 87% respectively. Nodal metastasis occurred in 6 patients in each group. Five-year nodal control rates of the LDR and HDR groups were 77% and 76%, respectively. Conclusion: Hyperfractionated HDR-ISRT for early mobile tongue cancer has the same local control compared with continuous LDR-ISRT. Hyperfractionated HDR-ISRT is an alternative treatment for continuous LDR-ISRT

  14. The Qinshan phase III project-a successful model of sino-canadian cooperation

    International Nuclear Information System (INIS)

    Pang, S.H.H.; Alikhan, S.; Gu Jun

    2005-01-01

    The Qinshan Phase III (CANDU) Project, the largest-scale cooperative project between China and Canada, was completed in 2003 well in advance of the schedule and 10% under budget. The Third Qinshan (Phase III) Nuclear Power Plant (TQNPP) was built in record times: Unit 1 achieved commercial operation on December 31, 2002 and Unit 2 on July 20, 2003, 43 days and 115 days ahead of schedule respectively. Improvements in design and construction methods allowed Unit 1 to be constructed in 51.5 months from First Concrete to Criticality - a record in China for nuclear power plants. The key factors are project management and project management tools, quality assurance, construction methods, electronic documentation with configuration control that provides up-to-date on-line information, CADDS design linked with material management and control. New design and construction techniques were introduced by combining conventional AECL practices with working experiences in China. The most advanced tools and techniques for achieving optimum construction quality, schedule and cost were used. Successful application of advanced project management methods and tools has benefited TQNPC in its subsequent plant operation, and the Chinese contractors in advancing their capabilities in future nuclear projects in China as well as enhancing their opportunities internationally. Excellent co-operation and teamwork within the integrated TQNPC/AECL Commissioning Team with well documented QA program, process and procedures also contributed to the remarkable success of the Project. AECL's initial assessment, based on lessons learned, showed that the project schedule could readily be reduced to 66 months and the capital costs reduced by 25% for a replication project. AECL is building on this experience and successful results of TQNPP in its Advanced CANDU Reactor TM (ACR TM ) ** design. (authors)

  15. Predicting hypothetical willingness to participate (WTP) in a future phase III HIV vaccine trial among high-risk adolescents.

    Science.gov (United States)

    Giocos, Georgina; Kagee, Ashraf; Swartz, Leslie

    2008-11-01

    The present study sought to determine whether the Theory of Planned Behaviour predicted stated hypothetical willingness to participate (WTP) in future Phase III HIV vaccine trials among South African adolescents. Hierarchical logistic regression analyses showed that The Theory of Planned Behaviour (TPB) significantly predicted WTP. Of all the predictors, Subjective norms significantly predicted WTP (OR = 1.19, 95% C.I. = 1.06-1.34). A stepwise logistic regression analysis revealed that Subjective Norms (OR = 1.19, 95% C.I. = 1.07-1.34) and Attitude towards participation in an HIV vaccine trial (OR = 1.32, 95% C.I. = 1.00-1.74) were significant predictors of WTP. The addition of Knowledge of HIV vaccines and HIV vaccine trials, Perceived self-risk of HIV infection, Health-promoting behaviours and Attitudes towards HIV/AIDS yielded non-significant results. These findings provide support for the Theory of Reasoned Action (TRA) and suggest that psychosocial factors may play an important role in WTP in Phase III HIV vaccine trials among adolescents.

  16. Author Contribution to the Pu Handbook II: Chapter 37 LLNL Integrated Sample Preparation Glovebox (TEM) Section

    Energy Technology Data Exchange (ETDEWEB)

    Wall, Mark A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-10-25

    The development of our Integrated Actinide Sample Preparation Laboratory (IASPL) commenced in 1998 driven by the need to perform transmission electron microscopy studies on naturally aged plutonium and its alloys looking for the microstructural effects of the radiological decay process (1). Remodeling and construction of a laboratory within the Chemistry and Materials Science Directorate facilities at LLNL was required to turn a standard radiological laboratory into a Radiological Materials Area (RMA) and Radiological Buffer Area (RBA) containing type I, II and III workplaces. Two inert atmosphere dry-train glove boxes with antechambers and entry/exit fumehoods (Figure 1), having a baseline atmosphere of 1 ppm oxygen and 1 ppm water vapor, a utility fumehood and a portable, and a third double-walled enclosure have been installed and commissioned. These capabilities, along with highly trained technical staff, facilitate the safe operation of sample preparation processes and instrumentation, and sample handling while minimizing oxidation or corrosion of the plutonium. In addition, we are currently developing the capability to safely transfer small metallographically prepared samples to a mini-SEM for microstructural imaging and chemical analysis. The gloveboxes continue to be the most crucial element of the laboratory allowing nearly oxide-free sample preparation for a wide variety of LLNL-based characterization experiments, which includes transmission electron microscopy, electron energy loss spectroscopy, optical microscopy, electrical resistivity, ion implantation, X-ray diffraction and absorption, magnetometry, metrological surface measurements, high-pressure diamond anvil cell equation-of-state, phonon dispersion measurements, X-ray absorption and emission spectroscopy, and differential scanning calorimetry. The sample preparation and materials processing capabilities in the IASPL have also facilitated experimentation at world-class facilities such as the

  17. Author Contribution to the Pu Handbook II: Chapter 37 LLNL Integrated Sample Preparation Glovebox (TEM) Section

    International Nuclear Information System (INIS)

    Wall, Mark A.

    2016-01-01

    The development of our Integrated Actinide Sample Preparation Laboratory (IASPL) commenced in 1998 driven by the need to perform transmission electron microscopy studies on naturally aged plutonium and its alloys looking for the microstructural effects of the radiological decay process (1). Remodeling and construction of a laboratory within the Chemistry and Materials Science Directorate facilities at LLNL was required to turn a standard radiological laboratory into a Radiological Materials Area (RMA) and Radiological Buffer Area (RBA) containing type I, II and III workplaces. Two inert atmosphere dry-train glove boxes with antechambers and entry/exit fumehoods (Figure 1), having a baseline atmosphere of 1 ppm oxygen and 1 ppm water vapor, a utility fumehood and a portable, and a third double-walled enclosure have been installed and commissioned. These capabilities, along with highly trained technical staff, facilitate the safe operation of sample preparation processes and instrumentation, and sample handling while minimizing oxidation or corrosion of the plutonium. In addition, we are currently developing the capability to safely transfer small metallographically prepared samples to a mini-SEM for microstructural imaging and chemical analysis. The gloveboxes continue to be the most crucial element of the laboratory allowing nearly oxide-free sample preparation for a wide variety of LLNL-based characterization experiments, which includes transmission electron microscopy, electron energy loss spectroscopy, optical microscopy, electrical resistivity, ion implantation, X-ray diffraction and absorption, magnetometry, metrological surface measurements, high-pressure diamond anvil cell equation-of-state, phonon dispersion measurements, X-ray absorption and emission spectroscopy, and differential scanning calorimetry. The sample preparation and materials processing capabilities in the IASPL have also facilitated experimentation at world-class facilities such as the

  18. Japanese contributions to IAEA INTOR workshop, phase two A, part 2, chapter III: impurity control (engineering)

    International Nuclear Information System (INIS)

    Seki, Masahiro; Miki, Nobuharu; Shibutani, Yoji; Fujimura, Kaoru; Adachi, Jun-ichi; Sato, Kosuke; Fujii, Masaharu; Yamazaki, Seiichiro; Itoh, Shin-ichi.

    1985-07-01

    This report corresponds to the second half of Chapter III of Japanese contribution report to IAEA INTOR Workshop, Phase Two A, Part 2. Data base assessment are made on candidate materials for the divertor, limiter, and the first wall. Engineering trade-off studies are made for the high-recycling and low temperature conditions. The studies include material considerations, configuration, thermohydraulic and stress analysis, disruption, lifetime analysis, and tritium permeation. (author)

  19. CSER 90-006, addendum 1: Criticality safety control for source term reduction project in the scrubber glovebox of Building 232-Z. Revision 1

    International Nuclear Information System (INIS)

    Hess, A.L.

    1995-01-01

    This Criticality Safety Evaluation Report addendum extends the coverage of the original CSER (90-006) about dismantling the ductwork in 232-Z to include cleanout of the Scrubber Glovebox, with an estimated residual Pu holdup of less than 200 grams. For conservatism and containment considerations, the provisions about waste packaging and water exclusion from the original work are retained, even though it is not credible for the Scrubber Pu content to be made critical with water added (NDA gives about 1/3 a minimum critical mass)

  20. SCOPE1: a randomised phase II/III multicentre clinical trial of definitive chemoradiation, with or without cetuximab, in carcinoma of the oesophagus

    International Nuclear Information System (INIS)

    Hurt, Christopher N; Nixon, Lisette S; Griffiths, Gareth O; Al-Mokhtar, Ruby; Gollins, Simon; Staffurth, John N; Phillips, Ceri J; Blazeby, Jane M; Crosby, Tom D

    2011-01-01

    Chemoradiotherapy is the standard of care for patients with oesophageal cancer unsuitable for surgery due to the presence of co-morbidity or extent of disease, and is a standard treatment option for patients with squamous cell carcinoma of the oesophagus. Modern regimens of chemoradiotherapy can lead to significant long-term survival. However the majority of patients will die of their disease, most commonly with local progression/recurrence of their tumours. Cetuximab may overcome one of the principal mechanisms of tumour radio-resistance, namely tumour repopulation, in patients treated with chemoradiotherapy. The purpose of this research is first to determine whether the addition of cetuximab to definitive chemoradiotherapy for treatment of patients with non-metastatic carcinoma of the oesophagus is active (in terms of failure-free rate), safe, and feasible within the context of a multi-centre randomised controlled trial in the UK. If the first stage is successful then the trial will continue to accrue sufficient patients to establish whether the addition of cetuximab to the standard treatment improves overall survival. SCOPE1 is a two arm, open, randomised multicentre Phase II/III trial. Eligible patients will have histologically confirmed carcinoma of the oesophagus and have been chosen to receive definitive chemoradiotherapy by an accredited multidisciplinary team including a specialist Upper GI surgeon. 420 patients will be randomised to receive definitive chemoradiotherapy with or without cetuximab using a 1:1 allocation ratio. During Phase II of the study, the trial will assess safety (toxicity), activity (failure-free rate) and feasibility (recruitment rate and protocol dose modifications/delays) in 90 patients in the experimental arm. If the experimental arm is found to be active, safe, and feasible by the Independent Data Monitoring Committee then recruitment will continue into Phase III. This second stage will recruit a further 120 patients into each arm

  1. SCOPE1: a randomised phase II/III multicentre clinical trial of definitive chemoradiation, with or without cetuximab, in carcinoma of the oesophagus

    Directory of Open Access Journals (Sweden)

    Staffurth John N

    2011-10-01

    Full Text Available Abstract Background Chemoradiotherapy is the standard of care for patients with oesophageal cancer unsuitable for surgery due to the presence of co-morbidity or extent of disease, and is a standard treatment option for patients with squamous cell carcinoma of the oesophagus. Modern regimens of chemoradiotherapy can lead to significant long-term survival. However the majority of patients will die of their disease, most commonly with local progression/recurrence of their tumours. Cetuximab may overcome one of the principal mechanisms of tumour radio-resistance, namely tumour repopulation, in patients treated with chemoradiotherapy. The purpose of this research is first to determine whether the addition of cetuximab to definitive chemoradiotherapy for treatment of patients with non-metastatic carcinoma of the oesophagus is active (in terms of failure-free rate, safe, and feasible within the context of a multi-centre randomised controlled trial in the UK. If the first stage is successful then the trial will continue to accrue sufficient patients to establish whether the addition of cetuximab to the standard treatment improves overall survival. Methods/Design SCOPE1 is a two arm, open, randomised multicentre Phase II/III trial. Eligible patients will have histologically confirmed carcinoma of the oesophagus and have been chosen to receive definitive chemoradiotherapy by an accredited multidisciplinary team including a specialist Upper GI surgeon. 420 patients will be randomised to receive definitive chemoradiotherapy with or without cetuximab using a 1:1 allocation ratio. During Phase II of the study, the trial will assess safety (toxicity, activity (failure-free rate and feasibility (recruitment rate and protocol dose modifications/delays in 90 patients in the experimental arm. If the experimental arm is found to be active, safe, and feasible by the Independent Data Monitoring Committee then recruitment will continue into Phase III. This second

  2. SAFOD Phase III Core Sampling and Data Management at the Gulf Coast Repository

    Directory of Open Access Journals (Sweden)

    David Lockner

    2011-03-01

    Full Text Available The San Andreas Fault Observatory at Depth (SAFODproject is yielding new insight into the San Andreas Fault (Zoback et al., 2010; Zoback et al., this issue. SAFOD drilling started in 2002 with a pilot hole, and proceeded with three phrases of drilling and coring during the summers of 2004, 2005, and 2007 (Fig. 1. One key component of theproject is curation, sampling, and documentation of SAFOD core usage at the Integrated Ocean Drilling Program’s (IODP Gulf Coast Repository (GCR at Texas A&M University. We present here the milestones accomplished over the past two years of sampling Phase III core at the GCR.

  3. Cyprus natural analogue project (CNAP). Phase III final report

    International Nuclear Information System (INIS)

    Alexander, W.R.; Milodowski, A.E.; Pitty, A.F.

    2012-01-01

    The CNAP Phase III project was carried out following identification of the requirement to support ongoing laboratory and modelling efforts on the potential reaction of the bentonite buffer with cementitious leachates in the repository EBS. Although it is known that the higher pH (12.5 to 13) leachates from OPC cement will degrade bentonite, it is unclear if this will also be the case for the lower pH (10 to 11) leachates typical of low alkali cements. Ongoing laboratory and URL programmes which are currently investigating this face the obstacle of slow kinetics and the production of short-lived metastable phases, meaning obtaining unambiguous results may take decades. This is exacerbated by the limitations of the thermodynamic databases for minerals of interest to models of bentonite/low alkali cement leachate reaction. It was therefore decided to implement a focussed NA study on bentonite/low alkali cement leachate reaction to provide indications of likely long-term reaction products and reaction pathways to provide feedback on the existing short-term investigations noted above and to ascertain if any critical path R and D needs to be instigated now. The results of the analyses presented here suggest that there has been very limited alkaline groundwater reaction with the bentonite. This is generally supported by both the geomorphological evidence and the natural decay series data which imply groundwater groundwater/rock interaction in the last 10 5 a. When integrated with the novel data currently being produced in the BIGRAD project, the CNAP data tend to indicate that any long-term bentonite reaction in low alkali cement leachates is minimal. (orig.)

  4. Cyprus natural analogue project (CNAP). Phase III final report

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, W R [Bedrock Geosciences, Auenstein (Switzerland); Milodowski, A E [British Geological Survey, Keyworth (United Kingdom); Pitty, A F [Pitty (EIA) Consulting, Norwich (United Kingdom)

    2012-01-15

    The CNAP Phase III project was carried out following identification of the requirement to support ongoing laboratory and modelling efforts on the potential reaction of the bentonite buffer with cementitious leachates in the repository EBS. Although it is known that the higher pH (12.5 to 13) leachates from OPC cement will degrade bentonite, it is unclear if this will also be the case for the lower pH (10 to 11) leachates typical of low alkali cements. Ongoing laboratory and URL programmes which are currently investigating this face the obstacle of slow kinetics and the production of short-lived metastable phases, meaning obtaining unambiguous results may take decades. This is exacerbated by the limitations of the thermodynamic databases for minerals of interest to models of bentonite/low alkali cement leachate reaction. It was therefore decided to implement a focussed NA study on bentonite/low alkali cement leachate reaction to provide indications of likely long-term reaction products and reaction pathways to provide feedback on the existing short-term investigations noted above and to ascertain if any critical path R and D needs to be instigated now. The results of the analyses presented here suggest that there has been very limited alkaline groundwater reaction with the bentonite. This is generally supported by both the geomorphological evidence and the natural decay series data which imply groundwater groundwater/rock interaction in the last 10{sup 5} a. When integrated with the novel data currently being produced in the BIGRAD project, the CNAP data tend to indicate that any long-term bentonite reaction in low alkali cement leachates is minimal. (orig.)

  5. Long-Term Management Strategy for Dredged Material Disposal for Naval Facilities at Pearl Harbor, Hawaii Phase III - Analysis of Alternatives and Development of an LTMS

    National Research Council Canada - National Science Library

    Palermo, Michael

    2000-01-01

    This report documents Phase III of a three-phase study to develop a Long-Term Management Study for disposal of dredged material unsuitable for ocean disposal from Pearl Harbor Naval Complex for the next 30 years...

  6. The application and design of distributed control system in reactor shutdown system of Qinshan phase III

    International Nuclear Information System (INIS)

    Su Guoquan; Liu Wangtian; Yu Yijun; Xiong Weihua

    2006-03-01

    The design, commissioning and running of the reactor trip parameter monitoring system used in Qinshan Phase III are introduced. The applying technology of Distributed Control System realized trip parameter monitoring and realized the function of trip parameters quick data acquisitioning, transferring, saving, alarm, query. The applying of trip parameters monitoring system improved the abilities of plant status monitoring and event analyzing, and increased the security and economy of nuclear power plant. (authors)

  7. Utilization of modified corn silk as a biosorbent for solid-phase extraction of Cr(III) and chromium speciation.

    Science.gov (United States)

    Yu, Hongmei; Pang, Jing; Wu, Mei; Wu, Qiaoli; Huo, Cuixiu

    2014-01-01

    The ues of corn silk modified with diluted nitric acid (HNO3-MCS) as a novel biosorbent has been established for solid-phase extraction of Cr(III) and chromium speciation in water samples. The functional groups of the HNO3-MCS surface are favorable for the adsorption of Cr(III). Effective extraction conditions were optimized in both batch and column methods. At pH 3.0 - 6.0, a discrimination of Cr(III) and Cr(VI) is achieved on the HNO3-MCS surface. Cr(III) ions are retained onto the HNO3-MCS surface, however, the adsorption of Cr(VI) is negligible under the same conditions. The adsorption isotherm of HNO3-MCS for Cr(III) has been demonstrated in accordance with a linear form of the Langmuir equation, and the maximum adsorption capacity is 35.21 mg g(-1). The well fitted linear regression of the pseudo-second order model showed the indication of a chemisorption mechanism for the entire concentration range. Thermodynamic studies have shown that the adsorption process is spontaneous and endothermic. The adsorbed Cr(III) was quantitatively eluted by a nitric acid solution with detection by flame atomic absorption spectrometry (FAAS). With a sample volume of 30 mL, a detection limit (3σ) of 0.85 μg L(-1) and a precision of 2.0% RSD at the 40 μg L(-1) level were achieved. The concentration of Cr(III) could be accurately quantified within a linear range of 3 - 200 μg L(-1). After Cr(VI) has been reduced to Cr(III) with hydroxylamine hydrochloride, the total amount of chromium was obtained, and the content of Cr(VI) was given by subtraction. The procedure was validated by analyzing chromium in a certified reference material (GBW (E) 080039). It was also successfully applied for the speciation of chromium in wastewater samples.

  8. Phase Equilibria in the Bi-In-Sn-Zn System. Thermal Analysis vs. Calculations

    Directory of Open Access Journals (Sweden)

    Dębski A.

    2017-12-01

    Full Text Available With the use of the differential thermal analysis (DTA, studies of the phase transitions were conducted for 90 of alloys from the quaternary Bi-In-Sn-Zn system and for the constant ratio of Bi:In and Bi:Sn. The studies were conducted for the alloys prepared from the purity metals (Bi, In, Sn, Zn = 99.999 mas. % by way of melting in a graphite crucible in a glove-box filled with Ar, in which the impurities level was less than 0.1 ppm. After melting and thorough mixing, the liquid alloys were poured out into a graphite test mold. The phase transition temperature data obtained from the DTA investigations were next confronted with those determined from the calculations based on the binary and ternary optimized thermodynamic parameters available in the literature. It was found that the experimental and the calculated phase transition temperatures were in good agreement.

  9. Heterogeneous FDG-guided dose-escalation for locally advanced NSCLC (the NARLAL2 trial): Design and early dosimetric results of a randomized, multi-centre phase-III study

    DEFF Research Database (Denmark)

    Møller, Ditte Sloth; Nielsen, Tine Bjørn; Brink, Carsten

    2017-01-01

    Background and purpose: Local recurrence is frequent in locally advanced NSCLC and is primarily located in FDG-avid parts of tumour and lymph nodes. Aiming at improving local control without increasing toxicity, we designed a multi-centre phase-III trial delivering inhomogeneous dose-escalation d......Background and purpose: Local recurrence is frequent in locally advanced NSCLC and is primarily located in FDG-avid parts of tumour and lymph nodes. Aiming at improving local control without increasing toxicity, we designed a multi-centre phase-III trial delivering inhomogeneous dose...

  10. Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in CMPO-HDEHP impregnated resins

    Energy Technology Data Exchange (ETDEWEB)

    Saipriya, K.; Kumar, T. [Bhabha Atomic Research Centre Facilities (India). Kalpakkam Reproscessing Plants; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2016-05-01

    Chromatographic resin containing extractants such as octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of extractants (CMPO + HDEHP) in an acrylic polymer matrix was prepared and studied for the extraction of Am(III) and Eu(III) over a range of nitric acid concentration. The effect of various parameters such as concentration of nitric acid in aqueous phase and the concentration of CMPO and HDEHP in the resin phase was studied. The distribution coefficient of Am(III) and Eu(III) in the impregnated resin increased with increased in the concentration of nitric acid for CMPO-impregnated resin, whereas a reverse trend was observed in HDEHP impregnated resin. In case of resin containing both the extractants, synergism was observed at low nitric acid concentration and antagonism at high nitric acid concentration. The mechanism of extraction was probed by slope analysis method at 0.01 and 2 M nitric acid concentrations. Citrate-buffered DTPA was used for the selective separation of Am(III), and a separation factor of 3-4 was obtained at pH 3.

  11. Rape embryogenesis. III. Embryo development in time

    Directory of Open Access Journals (Sweden)

    Teresa Tykarska

    2014-01-01

    Full Text Available It was found that the growth curve of the rape embryo axis is of triple sigmoid type. Embryo growth occurs in 3 phases corresponding to 3 different periods of development. Phase I includes growth of the apical cell up to it's division into two layers of octants. Phase II comprises the increase of the spherical proembryo to the change of its symmetry from radial to bilateral. Phase III includes, growth of the embryo from the heart stage up to the end of embryogenesis. In each phase the relative growth rate increases drastically and then diminishes. The differences in growth intensity during the same phase are several-fold. The growth intensity maximum of the embryo axis occurs in phase II. The phasic growth intensity maxima occur: in phase I during apical cell elongation, :before its division, and in phases II and III in the periods of cell division ;growth in globular and torpedo-shaped -shaped embryos.

  12. Phase I decontamination of the J.C. Haynes site, Newark, Ohio. Final report

    International Nuclear Information System (INIS)

    Emswiler, T.R.

    1985-11-01

    Phase I consisted of the primary decontamination, packaging, and shipment of all 241 Am-contaminated gloveboxes, vent system, and miscellaneous waste items located in the laboratory restricted area in the J.C. Haynes house. The primary goals of Phase I were to locate and account for a major quantity of 241 Am which was unaccounted for and to remove all radioactive materials and contamination posing an imminent hazard to public health and safety. All Phase I operations were conducted under a Quality Assurance (QA) Program Plan and QA procedures written specifically for this program. In addition, certain generic Battelle QA procedures were used for routine tasks. All operations were conducted under strict health physics supervision and procedures. Cognizant ORAU and US Nuclear Regulatory Commission (NRC) personnel were on site during the entire Phase I operation and provided support and approval in the daily operations. All staff members had participated in previous decontamination and decommissioning programs involving transuranic waste and completed Phase I in a well controlled, timely, and safe manner

  13. Project 8, Phase III Design: Placing an eV-Scale Limit on the Neutrino Mass using Cyclotron Radiation Emission Spectroscopy

    Science.gov (United States)

    Oblath, Noah; Project 8 Collaboration

    2016-09-01

    We report on the design concept for Phase III of the Project 8 experiment. In the third phase of Project 8 we aim to place a limit on the neutrino mass that is similar to the current limits set by tritium beta-decay experiments, mν radioastronomy will be employed to search for and track electron signals in the fiducial volume. This talk will present the quantitative design concept for the phased-array receiver, and illustrate how we are progressing towards the Phase IV experiment, which will have sensitivity to the neutrino mass scale allowed by the inverted mass hierarchy. This work is supported by the DOE Office of Science Early Career Research Program, and the Laboratory Directed Research and Development Program at Pacific Northwest National Laboratory.

  14. In situ remediation of plutonium from glovebox exhaust ducts at the Department of Energy's Rocky Flats Plant

    International Nuclear Information System (INIS)

    Dugdale, J.S.; Humiston, T.J.; Omer, G.E.

    1993-01-01

    Plutonium and other miscellaneous hold-up materials have been accumulating in the glovebox exhaust ducts at the Rocky Flats Plant over the 40 years of weapons production at the site. The Duct Remediation Project was undertaken to assess the safety impacts of this material, and to remove it from the ductwork. The project necessitated the development of specialized tools, equipment and methods to remediate the material from continuously operating ventilation systems. Special engineered access locations were also required to provide access to the ductwork, and to ensure that safety and system operability were not degraded as a result of the remediation efforts. Operations personnel underwent significant training and development, and became an important asset to the success of the project. In total, the project succeeded in removing over 40 kilograms of plutonium-bearing material from one of the major weapons production buildings at the plant

  15. Investor Outlook: Significance of the Positive LCA2 Gene Therapy Phase III Results.

    Science.gov (United States)

    Schimmer, Joshua; Breazzano, Steven

    2015-12-01

    Spark Therapeutics recently reported positive phase III results for SPK-RPE65 targeting the treatment of visual impairment caused by RPE65 gene mutations (often referred to as Leber congenital amaurosis type 2, or LCA2, but may include other retinal disorders), marking an important inflection point for the field of gene therapy. The results highlight the ability to successfully design and execute a randomized trial of a gene therapy and also reinforce the potentially predictive nature of early preclinical and clinical data. The results are expected to pave the way for the first approved gene therapy product in the United States and should sustain investor interest and confidence in gene therapy for many approaches, including retina targeting and beyond.

  16. A randomized placebo-controlled phase III trial of oral laquinimod for multiple sclerosis

    DEFF Research Database (Denmark)

    Vollmer, T L; Sorensen, P S; Selmaj, K

    2014-01-01

    The phase III placebo-controlled BRAVO study assessed laquinimod effects in patients with relapsing-remitting MS (RRMS), and descriptively compared laquinimod with interferon beta (IFNβ)-1a (Avonex(®) reference arm). RRMS patients age 18-55 years with Expanded Disability Status Scale (EDSS) scores...... months. The primary endpoint was annualized relapse rate (ARR); secondary endpoints included percent brain volume change (PBVC) and 3-month confirmed disability worsening. In all, 1,331 patients were randomized: laquinimod (n = 434), placebo (n = 450), and IFNβ-1a (n = 447). ARR was not significantly...... reduced with laquinimod [-18 %, risk ratio (RR) = 0.82, 95 % CI 0.66-1.02; p = 0.075] vs. placebo. Laquinimod significantly reduced PBVC (28 %, p change in confirmed disability worsening with laquinimod measured...

  17. The Effects of PECS Teaching to Phase III on the Communicative Interactions between Children with Autism and Their Teachers

    Science.gov (United States)

    Carr, Deborah; Felce, Janet

    2007-01-01

    The study investigated the impact of mastery of the Picture Exchange Communication System (PECS) to Phase III, on the communications of children with autism. Children aged between 3 and 7 years, formed a PECS intervention group and a non-intervention control group. The intervention group received 15 h of PECS teaching over 5 weeks. Three 2-h…

  18. Phenomenology of Polymorphism, III: p, TDiagram and Stability of Piracetam Polymorphs

    Science.gov (United States)

    Céolin, R.; Agafonov, V.; Louër, D.; Dzyabchenko, V. A.; Toscani, S.; Cense, J. M.

    1996-02-01

    The nootropic drug Piracetam is known to crystallize in three phases. In order to obtain their stability hierarchy from sublimation pressure inequalities, the drawing of a topologicalp,Tdiagram was attempted. For such a purpose and also for quality control, crystallographic and thermodynamic data were required. Powder X-ray diffractometry (XRD) and differential scanning calorimetry (DSC) were used. Molecular energy calculations were performed. Phase I melts at 426 K (ΔfusH(I) = +180 J·g-1). Phase II transforms into Phase I at 399 K (Δ(II→I)H= +24 J·g-1). Phase III transforms into phase I at 392 K (Δ(III→I)H= +28 J·g-1) or melts at 412 K (ΔfusH(III) = +210 J·g-1). Thep,Tdiagram shows that phase I is stable at higher temperature and phase II at lower temperature, like phase III, which is stable under high pressure. At room temperature, phase II is the more stable form, and phase I the less stable one. This agrees with the spontaneous I → II transformation observed at 298 K within a few hours, and with lattice energies, calculated previously. Molecular energy calculations and crystal structure comparison show how intermolecular hydrogen bonds and H-bonded dimers, in phases II and III, may stabilize conformations higher in energy than those of the isolated molecule and of phase I.

  19. A phase III trial of zoladex and flutamide versus orchiectomy in the treatment of patients with advanced carcinoma of the prostate

    DEFF Research Database (Denmark)

    Iversen, P; Christensen, M G; Friis, E

    1990-01-01

    In a multicenter Phase III trial 264 patients with advanced prostatic cancer were randomized to either bilateral orchiectomy or treatment with zoladex supplemented by flutamide. Presently, median follow-up time is 30 months. A small difference in objective response was recorded in favor of the co......In a multicenter Phase III trial 264 patients with advanced prostatic cancer were randomized to either bilateral orchiectomy or treatment with zoladex supplemented by flutamide. Presently, median follow-up time is 30 months. A small difference in objective response was recorded in favor...... of the combination therapy, whereas no statistically significant difference was found in subjective response to therapy, time to progression, and overall survival. Adverse effects were more commonly encountered in the pharmacologically treated patients. It is concluded that the combination of zoladex plus flutamide...... is not clinically superior to orchiectomy in the treatment of patients with advanced carcinoma of the prostate....

  20. DIAGNOSTIC GUIDANCE AND EARLY INTERVENTION IN CLASS III MALOCCLUSION

    Directory of Open Access Journals (Sweden)

    Rinandri Charea Runizar

    2015-06-01

    Full Text Available Timing of orthodontic treatment for Class III malocclusion has always been somewhat controversial. Many orthodontic pioneers like Angle, Tweed, and Graber have advocated early interception of class II malocclusion because this kind of skeletal discrepancy once established, would usually progress rapidly. What kind of early treatment would be appropriate for this malocclusion? Would this approach be effective and promises a stable result? Early orthodontic treatment is defined as a treatment that is initiated during the primary or mixed dentition stage to enhance skeletal and dental development. It is usually done in two phases. The first phase is intended to correct skeletal discrepancy by taking advantage of growth and development period. The second phase followed to improve occlusal relationship. Early treatment of Class III malocclusion is a possible alternative to improve skeletal discrepancy or at the very east may serve to prevent a worsening malocclusion. Principles of Class III early treatment depend on whether it is dental Class III, functional Class III, or skeletal Class III. Practitioners should consider positive and negative factors of a patient before initiating treatment. Likewise, they should understand factors that affect prognosis and stability of the results.

  1. Kinetic of liquid-liquid extraction for uranyl nitrate and actinides (III) and lanthanides (III) nitrates by amide extractants

    International Nuclear Information System (INIS)

    Toulemonde, V.; CEA Centre d'Etudes de la Vallee du Rhone, 30 -Marcoule

    1995-01-01

    The kinetics of liquid-liquid extraction by amide extractants have been investigated for uranyl nitrate (monoamide extractants), actinides (III) and lanthanides (III) nitrates (diamide extractants). The transfer of the metallic species from the aqueous phase to the organic phase was studied using two experimental devices: ARMOLLEX (Argonne Modified Lewis cell for Liquid Liquid Extraction) and RSC (Rotating Stabilized Cell). The main conclusions are: for the extraction of uranyl nitrate by DEHDMBA monoamide, the rate-controlling step is the complexation of the species at the interface of the two liquids. Thus, an absorption-desorption (according to Langmuir theory) reaction mechanism was proposed; for the extraction of actinides (III) and lanthanides (III) nitrates in nitric acid media by DMDBTDMA diamide, the kinetic is also limited by interfacial reactions. The behavior of Americium and Europium is very similar as fare as their reaction kinetics are concerned. (author)

  2. Phase III Drilling Operations at the Long Valley Exploratory Well (LVF 51-20)

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Jacobson, R.D.

    1999-06-01

    During July-September, 1998, a jointly funded drilling operation deepened the Long Valley Exploratory Well from 7178 feet to 9832 feet. This was the third major drilling phase of a project that began in 1989, but had sporadic progress because of discontinuities in tiding. Support for Phase III came from the California Energy Commission (CEC), the International Continental Drilling Program (ICDP), the US Geological Survey (USGS), and DOE. Each of these agencies had a somewhat different agenda: the CEC wants to evaluate the energy potential (specifically energy extraction from magma) of Long Valley Caldera; the ICDP is studying the evolution and other characteristics of young, silicic calderas; the USGS will use this hole as an observatory in their Volcano Hazards program; and the DOE, through Sandia, has an opportunity to test new geothermal tools and techniques in a realistic field environment. This report gives a description of the equipment used in drilling and testing; a narrative of the drilling operations; compiled daily drilling reports; cost information on the project; and a brief summary of engineering results related to equipment performance and energy potential. Detailed description of the scientific results will appear in publications by the USGS and other researchers.

  3. Acute morbidity reduction using 3DCRT for prostate carcinoma; a randomised phase III study

    International Nuclear Information System (INIS)

    Koper, P.; Putten, W. van; Stroom, J.; Korevaar, G.; Heijmen, B.; Wijnmaalen, A.; Jansen, P.; Hanssens, P.; Griep, C.; Krol, A.; Samson, M.; Levendag, P.

    1997-01-01

    Purpose: A randomised phase III toxicity study (conventional vs conformal radiotherapy) was performed for prostatic carcinoma to study the effects on the (acute) morbidity of intestinal/rectosigmoid and bladder. The observed toxicity was compared with Dose Volume Histograms to reveal possible volume (reduction) effects. Methods: In the phase III study 266 T1-4 N0M0 prostate cancer patients were entered. Patients were randomised for conventional and conformal radiotherapy (total dose 66 Gy, minimum PTV dose 95% ICRU and a CTV-PTV margin of 10 mm in both study arms). The GTV was limited to the prostate only in T1 tumors. In all other patients the GTV was defined to be prostate and seminal vesicles for the complete treatment course. The CTV-PTV margin (10mm) was created by a automated program to ensure the minimum prescribed margin. The rectosigmoid was defined to be the rectum including the sigmoid within the Treatment Volume (ICRU). Acute toxicity was evaluated using the EORTC/RTOG morbidity score and weekly quality of life questionnaires. The radiation technique comparison was done by Dose volume Histogram analysis using the Area Under The Curve (AUC) for different dose levels. In this preliminary DVH analysis we present the data for the first 100 patients. Results: Patient and tumor characteristics were evenly distributed between both study groups. The maximum toxicity is reached at 75% of the tumordose (TD) (rectal grade I 59% grade II 26%, bladder grade I 48%, grade II 16% and grade III 1% [catheter for urinary retention]). Comparing both study arms there seems to be a reduction in intestinal morbidity (grade II and higher resp. 32% vs 19% p=0.02). Further analysis revealed a marked reduction in medication for anal symptoms; this accounts for a large part of the significant difference in intestinal toxicity (grade II conventional vs conformal rectosigmoid 18% vs 14% and anal 16% vs 8%). For bladder morbidity no difference for mobidity higher than grade I is

  4. Hysteroscopic Essure Inserts for Permanent Contraception: Extended Follow-Up Results of a Phase III Multicenter International Study.

    Science.gov (United States)

    Chudnoff, Scott G; Nichols, John E; Levie, Mark

    2015-01-01

    To describe safety, tolerability, and effectiveness results through 5 years of follow-up of a Phase III trial with Essure inserts. Multicenter, nonrandomized, single-arm international study (Canadian Task Force classification II-3). Thirteen clinical study centers in the United States, Europe, and Australia. A total of 518 previously fertile women seeking permanent contraception. The objective of the hysteroscopic sterilization procedure was bilateral Essure insert placement (ESS205 model) and tubal occlusion. Women with satisfactory device location and tube occlusion (based on modified hysterosalpingography [HSG]) were instructed to discontinue alternative contraception and to rely on Essure inserts for permanent contraception. The primary endpoint for the Phase III study was the rate of pregnancies occurring during the first year of relying (i.e., HSG-confirmed occlusion) on the Essure inserts for permanent contraception (i.e., 12 months after HSG). For the full 5 years of follow-up (5 years total of relying on the Essure inserts for contraception), the endpoints of interest were safety, prevention of pregnancy, and satisfaction. No pregnancies were reported among women relying on the Essure inserts who completed the full 5 years of follow-up. As of December 5, 2007, 449 women with successful bilateral placement relying on the Essure inserts contributed a total 24 942 woman-months of follow-up for assessing effectiveness. Overall, the Essure inserts were generally well tolerated, with participant comfort rated as "good" to "excellent" by 99% of women (382 of 385) after 5 years of use. Similarly, overall satisfaction was rated as "somewhat" to "very satisfied" by 98% of women (376 of 384) after 5 years of use. The majority of adverse events reported during the 5 years of follow-up were rated as either "mild" or "moderate" in severity. Three severe events (abdominal pain with very heavy periods and irregular menstrual bleeding) were reported in 2 subjects during

  5. Evaluate fundamental approaches to longwall dust control. Phase III report

    Energy Technology Data Exchange (ETDEWEB)

    Babbitt, C.; Bartlett, P.; Kelly, J.; Ludlow, J.; Mangolds, A.; Rajan, S.; Ruggieri, S.; Varga, E.

    1984-03-31

    The overall objective of the contract is to evaluate the effectiveness of available dust control technology for double-drum shearer longwall sections in a coordinated, systematic program at a few longwall test sections and to make the results available to the entire coal mining industry. This program is investigating nine different dust control techniques. These nine subprograms encompass a broad range of dust control measures ranging from administrative controls to new hardware. They span not only presently employed methods but also those recently adopted in the United States and those proposed for the future. This report documents the Phase III effort on each of the subprograms. For clarity, the report is divided in sections by subprogram as follows: Section 2, Subprogram A - passive barriers/spray air movers for dust control; Section 3, Subprogram B - practical aspects of deep cutting; Section 4, Subprogram C - stage loader dust control; Section 5, Subprogram D - longwall automation technology; Section 6, Subprogram E - longwall application of ventilation curtains; Section 7, Subprogram F - reversed drum rotation; Section 8, Subprogram G - reduction of shield generated dust; Section 9, Subprogram H - air canopies for longwalls; and Section 10, Subprogram I - mining practices. 43 figures, 11 tables.

  6. Analysis of Reasons for fluctuation in seal oil system on generator and countermeasures in Qinshan phase III project

    International Nuclear Information System (INIS)

    Jin Xiaodong

    2012-01-01

    Reasons for hydraulic differential fluctuations seal hydrogen oil on generator in Qinshan phase III project were analyzed, provide a basis for modifying Run method is to determine the causes and effects of seal oil flow changes and in the relationship between flow changes and hydraulic differential hydrogen oil changes according to reason Results were analyzed to adjust the running test, to verify the feasibility of running adjustment programs

  7. Bortezomib before and after high-dose therapy in myeloma : Long-term results from the phase III HOVON-65/GMMGHD-4 trial

    NARCIS (Netherlands)

    Goldschmidt, H.; Lokhorst, H. M.; Mai, E. K.; van der Holt, B.; Blau, I. W.; Zweegman, S.; Weisel, K. C.; Vellenga, E.; Pfreundschuh, M.; Kersten, M. J.; Scheid, C.; Croockewit, S.; Raymakers, R.; Hose, D.; Potamianou, A.; Jauch, A.; Hillengass, J.; Stevens-Kroef, M.; Raab, M. S.; Broijl, A.; Lindemann, H. W.; Bos, G. M. J.; Brossart, P.; Kooy, M. van Marwijk; Ypma, P.; Duehrsen, U.; Schaafsma, R. M.; Bertsch, U.; Hielscher, T.; Jarari, Le; Salwender, H. J.; Sonneveld, P.

    The Dutch-Belgian Cooperative Trial Group for Hematology Oncology Group-65/German-speaking Myeloma Multicenter Group-HD4 (HOVON-65/GMMG-HD4) phase III trial compared bortezomib (BTZ) before and after high-dose melphalan and autologous stem cell transplantation (HDM, PAD arm) compared with classical

  8. Bortezomib before and after high-dose therapy in myeloma: long-term results from the phase III HOVON-65/GMMGHD-4 trial

    NARCIS (Netherlands)

    Goldschmidt, H.; Lokhorst, H. M.; Mai, E. K.; van der Holt, B.; Blau, I. W.; Zweegman, S.; Weisel, K. C.; Vellenga, E.; Pfreundschuh, M.; Kersten, M. J.; Scheid, C.; Croockewit, S.; Raymakers, R.; Hose, D.; Potamianou, A.; Jauch, A.; Hillengass, J.; Stevens-Kroef, M.; Raab, M. S.; Broijl, A.; Lindemann, H. W.; Bos, G. M. J.; Brossart, P.; van Marwijk Kooy, M.; Ypma, P.; Duehrsen, U.; Schaafsma, R. M.; Bertsch, U.; Hielscher, T.; Jarari, Le; Salwender, H. J.; Sonneveld, P.

    2018-01-01

    The Dutch-Belgian Cooperative Trial Group for Hematology Oncology Group-65/German-speaking Myeloma Multicenter Group-HD4 (HOVON-65/GMMG-HD4) phase III trial compared bortezomib (BTZ) before and after high-dose melphalan and autologous stem cell transplantation (HDM, PAD arm) compared with classical

  9. Production circulator fabrication and testing for core flow test loop. Final report, Phase III

    Energy Technology Data Exchange (ETDEWEB)

    1981-05-01

    The performance testing of two production helium circulators utilizing gas film lubrication is described. These two centrifugal-type circulators plus an identical circulator prototype will be arranged in series to provide the helium flow requirements for the Core Flow Test Loop which is part of the Gas-Cooled Fast Breeder Reactor Program (GCFR) at the Oak Ridge National Laboratory. This report presents the results of the Phase III performance and supplemental tests, which were carried out by MTI during the period of December 18, 1980 through March 19, 1981. Specific test procedures are outlined and described, as are individual tests for measuring the performance of the circulators. Test data and run descriptions are presented.

  10. Production circulator fabrication and testing for core flow test loop. Final report, Phase III

    International Nuclear Information System (INIS)

    1981-05-01

    The performance testing of two production helium circulators utilizing gas film lubrication is described. These two centrifugal-type circulators plus an identical circulator prototype will be arranged in series to provide the helium flow requirements for the Core Flow Test Loop which is part of the Gas-Cooled Fast Breeder Reactor Program (GCFR) at the Oak Ridge National Laboratory. This report presents the results of the Phase III performance and supplemental tests, which were carried out by MTI during the period of December 18, 1980 through March 19, 1981. Specific test procedures are outlined and described, as are individual tests for measuring the performance of the circulators. Test data and run descriptions are presented

  11. Kinetic of liquid-liquid extraction for uranyl nitrate and actinides (III) and lanthanides (III) nitrates by amide extractants; Cinetique d`extraction liquide-liquide du nitrate d`uranyle et des nitrates d`actinides (III) et de lanthanides (III) par des extractants a fonction amide

    Energy Technology Data Exchange (ETDEWEB)

    Toulemonde, V [CEA Centre d` Etudes Nucleaires de Saclay, 91 -Gif-sur-Yvette (France); [CEA Centre d` Etudes de la Vallee du Rhone, 30 -Marcoule (France). Dept. d` Exploitation du Retraitement et de Demantelement

    1995-12-20

    The kinetics of liquid-liquid extraction by amide extractants have been investigated for uranyl nitrate (monoamide extractants), actinides (III) and lanthanides (III) nitrates (diamide extractants). The transfer of the metallic species from the aqueous phase to the organic phase was studied using two experimental devices: ARMOLLEX (Argonne Modified Lewis cell for Liquid Liquid Extraction) and RSC (Rotating Stabilized Cell). The main conclusions are: for the extraction of uranyl nitrate by DEHDMBA monoamide, the rate-controlling step is the complexation of the species at the interface of the two liquids. Thus, an absorption-desorption (according to Langmuir theory) reaction mechanism was proposed; for the extraction of actinides (III) and lanthanides (III) nitrates in nitric acid media by DMDBTDMA diamide, the kinetic is also limited by interfacial reactions. The behavior of Americium and Europium is very similar as fare as their reaction kinetics are concerned. (author). 89 refs.

  12. Adsorption of As(III), As(V) and Cu(II) on zirconium oxide immobilized alginate beads in aqueous phase.

    Science.gov (United States)

    Kwon, Oh-Hun; Kim, Jong-Oh; Cho, Dong-Wan; Kumar, Rahul; Baek, Seung Han; Kurade, Mayur B; Jeon, Byong-Hun

    2016-10-01

    A composite adsorbent to remove arsenite [As(III)], arsenate [As(V)], and copper [Cu(II)] from aqueous phase was synthesized by immobilizing zirconium oxide on alginate beads (ZOAB). The composition (wt%) of ZOAB (Zr-34.0; O-32.7; C-21.3; Ca-1.0) was confirmed by energy dispersive X-ray (EDX) analysis. Sorption studies were conducted on single and binary sorbate systems, and the effects of contact time, initial adsorbate concentration, and pH on the adsorption performance of ZOAB (pHPZC = 4.3) were monitored. The sorption process for As(III)/As(V) and Cu(II) reached an equilibrium state within 240 h and 24 h, respectively, with maximum sorption capacities of 32.3, 28.5, and 69.9 mg g(-1), respectively. The addition of Cu(II) was favorable for As(V) sorption in contrast to As(III). In the presence of 48.6 mg L(-1) Cu(II), the sorption capacity of As(V) increased from 1.5 to 3.8 mg g(-1) after 240 h. The sorption data for As(III)/As(V) and Cu(II) conformed the Freundlich and Langmuir isotherm models, respectively. The adsorption of As(III), As(V), and Cu(II) followed pseudo second order kinetics. The effect of arsenic species on Cu(II) sorption was insignificant. The results of present study demonstrated that the synthesized sorbent could be useful for the simultaneous removal of both anionic and cationic contaminants from wastewaters. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Direct disposal of spent fuel. Simulation of shaft transport. Phase III. Final report

    International Nuclear Information System (INIS)

    Filbert, W.; Heda, M.; Khamis, M.; Neydek, J.; Niehues, N.; Rissel, J.; Schrimpf, C.; Weber, W.; Fuchs, D.; Gerlach, A.; Langebrake, F.; Sindern, W.; Gasch, A.; Leicht, R.; Schwab, B.; Hecke, R. van; Kipka, P.; Simmich, K.; Weber, H.

    1994-01-01

    The aim of these demonstration tests was to verify the technical feasibility of a shaft hoisting equipment with a payload of 85 t as well as the safe transport of POLLUX-casks. In phase III of the project the components and the test stand were built, their proper functioning and reliability were tested to demonstrate that they are state-of-the-art. The following additional investigations were carried out: - Tests to fix operational disturbances and simulation tests for the new components to demonstrate their licensibility -Selection and lifetime tests of ropes and investigation of the present state-of-the-art of rope slighting under the conditions of the conceptual design of the shaft hoisting facility - Execution of a probabilistic safety analysis e.g. the determination of the release of radioactive material (result: probability [de

  14. Phase I-II study of everolimus and low-dose oral cyclophosphamide in patients with metastatic renal cell cancer

    International Nuclear Information System (INIS)

    Huijts, Charlotte M; Santegoets, Saskia J; Eertwegh, Alfons J van den; Pijpers, Laura S; Haanen, John B; Gruijl, Tanja D de; Verheul, Henk M; Vliet, Hans J van der

    2011-01-01

    For patients with metastatic renal cell cancer (mRCC) who progressed on vascular endothelial growth factor (VEGF) receptor tyrosine kinase inhibitor therapy, the orally administered mammalian target of rapamycin (mTOR) inhibitor everolimus has been shown to prolong progression free survival. Intriguingly, inhibition of mTOR also promotes expansion of immunosuppressive regulatory T cells (Tregs) that can inhibit anti-tumor immune responses in a clinically relevant way in various tumor types including RCC. This study intends to investigate whether the antitumor efficacy of everolimus can be increased by preventing the detrimental everolimus induced expansion of Tregs using a metronomic schedule of cyclophosphamide. This phase I-II trial is a national multi-center study of different doses and schedules of low-dose oral cyclophosphamide in combination with a fixed dose of everolimus in patients with mRCC not amenable to or progressive after a VEGF-receptor tyrosine kinase inhibitor containing treatment regimen. In the phase I part of the study the optimal Treg-depleting dose and schedule of metronomic oral cyclophosphamide when given in combination with everolimus will be determined. In the phase II part of the study we will evaluate whether the percentage of patients progression free at 4 months of everolimus treatment can be increased from 50% to 70% by adding metronomic cyclophosphamide (in the dose and schedule determined in the phase I part). In addition to efficacy, we will perform extensive immune monitoring with a focus on the number, phenotype and function of Tregs, evaluate the safety and feasibility of the combination of everolimus and cyclophosphamide, perform monitoring of selected angiogenesis parameters and analyze everolimus and cyclophosphamide drug levels. This phase I-II study is designed to determine whether metronomic cyclophosphamide can be used to counter the mTOR inhibitor everolimus induced Treg expansion in patients with metastatic renal cell

  15. Phase I-II study of everolimus and low-dose oral cyclophosphamide in patients with metastatic renal cell cancer

    Directory of Open Access Journals (Sweden)

    Huijts Charlotte M

    2011-11-01

    Full Text Available Abstract Background For patients with metastatic renal cell cancer (mRCC who progressed on vascular endothelial growth factor (VEGF receptor tyrosine kinase inhibitor therapy, the orally administered mammalian target of rapamycin (mTOR inhibitor everolimus has been shown to prolong progression free survival. Intriguingly, inhibition of mTOR also promotes expansion of immunosuppressive regulatory T cells (Tregs that can inhibit anti-tumor immune responses in a clinically relevant way in various tumor types including RCC. This study intends to investigate whether the antitumor efficacy of everolimus can be increased by preventing the detrimental everolimus induced expansion of Tregs using a metronomic schedule of cyclophosphamide. Methods/design This phase I-II trial is a national multi-center study of different doses and schedules of low-dose oral cyclophosphamide in combination with a fixed dose of everolimus in patients with mRCC not amenable to or progressive after a VEGF-receptor tyrosine kinase inhibitor containing treatment regimen. In the phase I part of the study the optimal Treg-depleting dose and schedule of metronomic oral cyclophosphamide when given in combination with everolimus will be determined. In the phase II part of the study we will evaluate whether the percentage of patients progression free at 4 months of everolimus treatment can be increased from 50% to 70% by adding metronomic cyclophosphamide (in the dose and schedule determined in the phase I part. In addition to efficacy, we will perform extensive immune monitoring with a focus on the number, phenotype and function of Tregs, evaluate the safety and feasibility of the combination of everolimus and cyclophosphamide, perform monitoring of selected angiogenesis parameters and analyze everolimus and cyclophosphamide drug levels. Discussion This phase I-II study is designed to determine whether metronomic cyclophosphamide can be used to counter the mTOR inhibitor everolimus

  16. Dismantling of a furnace and gloveboxes of a U{sub 3}O{sub 8} with 20% enrichment production line; Desmantelamiento de un horno y cajas de guantes de una linea de produccion de U{sub 3}O{sub 8} enriquecido al 20%

    Energy Technology Data Exchange (ETDEWEB)

    Yorio, Daniel; Cinat, Enrique; Cincotta, Daniel; Fernandez, Carlos A; Bruno, Hernan R; Camacho, Esteban F; Boero, Norma [Comision Nacional de Energia Atomica, General San Martin (Argentina). Dept. de Combustibles Nucleares

    1999-07-01

    In the Uranium Powder Manufacturing Plant at CAC, U{sub 3}O{sub 8} with 20% enrichment is manufactured for fuel plates to be used in test reactors. This plant is in full operation since 1986, producing uranium oxide for Peru, Algeria, Iran, Egypt and the RA-3-CAE reactors. Some of the equipment of the Plant have finished their life time and one of the furnaces of the processing line had to be replaced. This work implied the dismantling not only of the furnace, but also of the gloveboxes connected to the furnace and the dismantling of the extraction lines and air injection of the gloveboxes. The work had to be performed with the necessary care in order to minimize risks and effects on personnel, installations and environment involved. (author)

  17. WRAP Module 1 data management system (DMS) software design description (SDD)

    International Nuclear Information System (INIS)

    Weidert, J.R.

    1996-01-01

    Revision 2 of the Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS) Preliminary Software Design Description (PSDD) provides a high-level design description of the system. The WRAP 1 DMS is required to collect, store, and report data related to certification, tracking, packaging, repackaging, processing, and shipment of waste processed or stored at the WRAP 1 facility. The WRAP 1 DMS SDD is used as the primary medium for communication software design information. This release provides design descriptions for the following process modules produced under Phase 1 of the development effort: Receiving Drum or Box Containers Process Routing and Picklists; Waste Inventory by Location and/or Container Relationships; LLW Process Glovebox Facility Radiologic Material Inventory Check (partial); Shipping (partial production); Drum or Box NDE Operations; and Drum or Box NDA Operations Data Review (partial production). In addition, design descriptions are included for the following process modules scheduled for development under Phases 2 and 3: Activity Comment; LLW RWM Glovebox Sample Management; TRU Process Glovebox; TRU RWM Glovebox; and TRUPACT Processing. Detailed design descriptions for Reports and Facility Metrics have also been provided for in Revision 2 of this document

  18. Impact of baseline covariates on the immunogenicity of the 9-valent HPV vaccine - A combined analysis of five phase III clinical trials

    DEFF Research Database (Denmark)

    Petersen, Lone K; Restrepo, Jaime; Moreira, Edson D

    2017-01-01

    BACKGROUND: The immunogenicity profile of the 9-valent HPV (9vHPV) vaccine was evaluated across five phase III clinical studies conducted in girls and boys 9-15 years of age and young women 16-26 years of age. The effect of baseline characteristics of subjects on vaccine-induced HPV antibody...... responses was assessed. METHODS: Immunogenicity data from 11,304 subjects who received ≥1 dose of 9vHPV vaccine in five Phase III studies were analyzed. Vaccine was administered as a 3-dose regimen. HPV antibody titers were assessed 1 month after dose 3 using a competitive Luminex immunoassay and summarized...... as geometric mean titers (GMTs). Covariates examined were age, gender, race, region of residence, and HPV serostatus and PCR status at day 1. RESULTS: GMTs to all 9 vaccine HPV types decreased with age at vaccination initiation, and were otherwise generally similar among the demographic subgroups defined...

  19. SPIRIT: A seamless phase I/II randomized design for immunotherapy trials.

    Science.gov (United States)

    Guo, Beibei; Li, Daniel; Yuan, Ying

    2018-06-07

    Immunotherapy-treatments that enlist the immune system to battle tumors-has received widespread attention in cancer research. Due to its unique features and mechanisms for treating cancer, immunotherapy requires novel clinical trial designs. We propose a Bayesian seamless phase I/II randomized design for immunotherapy trials (SPIRIT) to find the optimal biological dose (OBD) defined in terms of the restricted mean survival time. We jointly model progression-free survival and the immune response. Progression-free survival is used as the primary endpoint to determine the OBD, and the immune response is used as an ancillary endpoint to quickly screen out futile doses. Toxicity is monitored throughout the trial. The design consists of two seamlessly connected stages. The first stage identifies a set of safe doses. The second stage adaptively randomizes patients to the safe doses identified and uses their progression-free survival and immune response to find the OBD. The simulation study shows that the SPIRIT has desirable operating characteristics and outperforms the conventional design. Copyright © 2018 John Wiley & Sons, Ltd.

  20. Optimized FFTF Acceptance Test Program covering Phases III, IV, and V

    International Nuclear Information System (INIS)

    Wykoff, W.R.; Jones, D.H.

    1977-03-01

    A detailed review of Phases III, IV, and V of the FFTF Acceptance Test Program has been completed. The purpose of this review was to formulate that test sequence which not only meets requirements for safe, reliable and useful operation of the plant, but also results in the earliest prudent demonstration of full-power performance. A test sequence based on the underlying assumption that sodium flows into the secondary sodium storage tank (T-44) no later than August 31, 1978, is described in detail. A time-scale which allows extra time to put systems and equipment into operation the first time, debugging, and learning how to operate most effectively has been superimposed on the test sequence. Time is not included for major equipment malfunctions. This test plan provides the basis for coordinating the many and varied activities and interfaces necessary for successful and timely execution of the FFTF Acceptance Test Program. In this report, the need dates have been identified for presently scheduled test articles and standard core components

  1. Study Protocol: Phase III single-blinded fast-track pragmatic randomised controlled trial of a complex intervention for breathlessness in advanced disease

    Directory of Open Access Journals (Sweden)

    Brafman-Kennedy Barbara

    2011-05-01

    Full Text Available Abstract Background Breathlessness in advanced disease causes significant distress to patients and carers and presents management challenges to health care professionals. The Breathlessness Intervention Service (BIS seeks to improve the care of breathless patients with advanced disease (regardless of cause through the use of evidence-based practice and working with other healthcare providers. BIS delivers a complex intervention (of non-pharmacological and pharmacological treatments via a multi-professional team. BIS is being continuously developed and its impact evaluated using the MRC's framework for complex interventions (PreClinical, Phase I and Phase II completed. This paper presents the protocol for Phase III. Methods/Design Phase III comprises a pragmatic, fast-track, single-blind randomised controlled trial of BIS versus standard care. Due to differing disease trajectories, the service uses two broad service models: one for patients with malignant disease (intervention delivered over two weeks and one for patients with non-malignant disease (intervention delivered over four weeks. The Phase III trial therefore consists of two sub-protocols: one for patients with malignant conditions (four week protocol and one for patients with non-malignant conditions (eight week protocol. Mixed method interviews are conducted with patients and their lay carers at three to five measurement points depending on randomisation and sub-protocol. Qualitative interviews are conducted with referring and non-referring health care professionals (malignant disease protocol only. The primary outcome measure is 'patient distress due to breathlessness' measured on a numerical rating scale (0-10. The trial includes economic evaluation. Analysis will be on an intention to treat basis. Discussion This is the first evaluation of a breathlessness intervention for advanced disease to have followed the MRC framework and one of the first palliative care trials to use fast

  2. High-pressure single-crystal elasticity study of CO{sub 2} across phase I-III transition

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jin S., E-mail: zhang72@illinois.edu; Bass, Jay D. [Department of Geology, University of Illinois, Urbana-Champaign, Illinois 61801 (United States); Shieh, Sean R. [Departments of Earth Sciences and Physics and Astronomy, University of Western Ontario, London, Ontario N6A 5B7 (Canada); Dera, Przemyslaw [Hawaii Institute of Geophysics and Planetology, University of Hawaii at Manoa, Honolulu, Hawaii 96822 (United States); Prakapenka, Vitali [Center for Advanced Radiation Sources, University of Chicago, Chicago, Illinois 60637 (United States)

    2014-04-07

    Sound velocities and elastic moduli of solid single-crystal CO{sub 2} were measured at pressures up to 11.7(3) GPa by Brillouin spectroscopy. The aggregate adiabatic bulk modulus (K{sub S}), shear modulus (G), and their pressure derivatives for CO{sub 2} Phase I are K{sub S0} = 3.4(6) GPa, G{sub 0} = 1.8(2) GPa, (dK{sub S}/dP){sub 0} = 7.8(3), (dG/dP){sub 0} = 2.5(1), (d{sup 2}K{sub S}/dP{sup 2}){sub 0} = −0.23(3) GPa{sup −1}, and (d{sup 2}G/dP{sup 2}){sub 0} = −0.10(1) GPa{sup −1}. A small increase of elastic properties was observed between 9.8(1) and 10.5(3) GPa, in agreement with the CO{sub 2} I-III transition pressure determined from previous x-ray diffraction experiments. Above the transition pressure P{sub T}, we observed a mixture dominated by CO{sub 2}-I, with minor CO{sub 2}-III. The CO{sub 2}-I + III mixture shows slightly increased sound velocities compared to pure CO{sub 2}-I. Elastic anisotropy calculated from the single-crystal elasticity tensor exhibits a decrease with pressure beginning at 7.9(1) GPa, which is lower than P{sub T}. Our results coincide with recent X-ray Raman observations, suggesting that a pressure-induced electronic transition is related to local structural and optical changes.

  3. Liquid-liquid extraction of ruthenium(III) thiocyanate with hexamethylphosphoramide: direct spectrophotometric determination in the organic phase

    International Nuclear Information System (INIS)

    Mitra, B.K.; Pal, B.K.; Chowdhury, R.P.

    1982-01-01

    Ru(III) thiocyanate has been extracted with hexamethylphosphoramide(HMPA) in methyl isobutyl ketone (MIBK). Thus the extractability, sensitivity and selectivity are improved over the simple binary Ru(III) thiocyanate system in spectrophotometric determination of ruthenium in the organic phase. The maximum colour develops on the steam bath, at the acidity range of 1.5 - 2.5 M with HCl and ammonium thiocyanate concentration range of 0.25 - O.5 M. The colour is completely extractable in MIBK when 1.5 - 3.0 ml HMPA is used and show maximum absorbance at 570 nm. The colour system obeys Beer's law for 0.7 - 13 μg Ru/ml and the optimum concentration range is 2 - 13 μg/ml. The molar absorptivity and sensitivity are 6940 l . mole -1 cm -1 and 0.0145 μg/cm 2 respectively. The percent relative error is 2.72%. The method is very simple and does not require oxidation and subsequent distillation. The method can be applied in the presence of osmium. (Author)

  4. Runaway electron damage to the Tore Supra Phase III outboard pump limiter

    International Nuclear Information System (INIS)

    Nygren, R.; Lutz, T.; Walsh, D.; Martin, G.; Chatelier, M.; Loarer, T.; Guilhem, D.

    1996-01-01

    Operation of the Phase III outboard pump limiter (OPL) in Tore Supra in 1994 was terminated prematurely when runaway electrons during the current decay following a disruption pierced leading edge tube on the electron side and caused a water leak. The location, about 20 mm outside the last closed flux surface during normal operation, and the infrared (IR) images of the limiter indicate that the runaways moved in large outward steps, i.e. tens of millimeters, in one toroidal revolution. For plasma (runaway) currents in the range of 155 to 250 kA, the drift orbits open to the outside. Basic trajectory computations suggest that such motion is possible under the conditions present for this experiment. Activation measurements made on sections of the tube to indicate the area of local damage are presented here. An understanding of this event may provide important guidance regarding the potential damage from runaways in future tokamaks

  5. Extraction of lanthanide(III) nitrates from water-salt solutions with n.-octanol

    International Nuclear Information System (INIS)

    Keskinov, V.A.; Kudrova, A.V.; Valueva, O.V.; Pyartman, A.K.

    2004-01-01

    Extraction of lanthanide(III) nitrates (Ln=La-Nd, Sm-Gd) from aqueous-salt solutions at 298.15 K was studied using solution of n.-octanol, its concentration 6.31 mol/l. It was ascertained that at Ln(NO 3 ) 3 concentration in aqueous phase below 0.6 mol/l, there is actually no extraction. At higher concentrations of nitrates in aqueous phase the content of lanthanides(III) in organic phase increases in the series La-Gd. Isotherms of extraction were ascertained, its phase equilibria being described mathematically. It is shown that extraction of lanthanide(III) nitrates with n.-octanol should be realized from concentrated aqueous solutions [ru

  6. The Phase I/II BNCT Trials at the Brookhaven medical research reactor: Critical considerations

    International Nuclear Information System (INIS)

    Diaz, A.Z.

    2001-01-01

    A phase I/II clinical trial of boronophenylalanine-fructose (BPA-F) mediated boron neutron capture therapy (BNCT) for Glioblastoma Multiforme (GBM) was initiated at Brookhaven National Laboratory (BNL) in 1994. Many critical issues were considered during the design of the first of many sequential dose escalation protocols. These critical issues included patient selection criteria, boron delivery agent, dose limits to the normal brain, dose escalation schemes for both neutron exposure and boron dose, and fractionation. As the clinical protocols progressed and evaluation of the tolerance of the central nervous system (CNS) to BPA-mediated BNCT at the BMRR continued new specifications were adopted. Clinical data reflecting the progression of the protocols will be presented to illustrate the steps taken and the reasons behind their adoption. (author)

  7. Phase II Results of RTOG 0537: A Phase II/III Study Comparing Acupuncture-like Transcutaneous Electrical Nerve Stimulation Versus Pilocarpine in Treating Early Radiation-Induced Xerostomia

    Science.gov (United States)

    Wong, Raimond K. W.; James, Jennifer L.; Sagar, Stephen; Wyatt, Gwen; Nguyen-Tân, Phuc Felix; Singh, Anurag K.; Lukaszczyk, Barbara; Cardinale, Francis; Yeh, Alexander M.; Berk, Lawrence

    2011-01-01

    Purpose This phase II component of a multi-institutional phase II/III randomized trial assessed the feasibility and preliminary efficacy of acupuncture-like transcutaneous electrical nerve stimulation (ALTENS) in reducing radiation-induced xerostomia. Methods Head and neck cancer patients who were 3–24 months from completing radiotherapy ± chemotherapy (RT±C) and experiencing xerostomia symptoms with basal whole saliva production ≥0.1 ml/min and without recurrence were eligible. Patients received twice weekly ALTENS sessions (24 over 12 weeks) using a Codetron™ unit. The primary objective assessed the feasibility of ALTENS treatment. A patient was considered compliant if 19/24 ALTENS were delivered, with a targeted 85% compliance rate. Secondary objectives measured treatment-related toxicities and ALTENS effect on overall radiation-induced xerostomia burden using the University of Michigan Xerostomia-Related Quality of Life Scale (XeQOLS). Results Of 48 accrued patients, 47 were evaluable. Median age was 60 years; 84% were male, 70% completed RT±C for > 12 months and 21% had received prior pilocarpine. All ALTENS sessions were completed in 34 patients, but 9 and 1 completed 20–23 and 19 sessions respectively, representing a 94% total compliance rate. 6-month XeQOLS scores were available for 35 patients; 30 (86%) achieved a positive treatment response with a mean reduction of 35.9% (SD 36.1). Five patients developed grade 1–2 gastrointestinal toxicity and one had grade 1 pain event. Conclusions ALTENS treatment for radiation-induced xerostomia can be uniformly delivered in a cooperative multicenter setting and has possible beneficial treatment response. Given these results, the phase III component of this study was initiated. PMID:22252927

  8. Study on the extraction characteristics of Fe(III) with trialkylphosphine oxide

    International Nuclear Information System (INIS)

    Zhang Qiwei; Jiao Rongzhou; Song Chongli

    1994-08-01

    The extractive properties of TRPO (trialkyephosphine oxide) as the extractant for the Fe(III) have been studied. Under this experiment condition, the distribution ratio D of Fe (III) with the changes of extraction equilibrium time, temperature, nitric acid concentration and Fe 3+ concentration in aqueous solution have been determined. The ΔH degree, ΔS degree and apparent equilibrium constant K of the reaction in which Fe (III) is extracted by TRPO have been calculated. The experiment results show that the third phase appearance in 30% TRPO extractive system has close relations with Fe 3+ concentration in aqueous solution. When nitric acid concentration is 1.5 mol/L and Fe 3+ initial concentration is higher than 8.0 g/L in aqueous solution, the extractant system appears third phase. Two organic phase volume ratio and Fe(III) concentration ratio in the organic phases have been determined respectively, and they vary with the Fe 3+ concentration in aqueous solution

  9. The Combination Process for Preparative Separation and Purification of Paclitaxel and 10-Deacetylbaccatin III Using Diaion® Hp-20 Followed by Hydrophilic Interaction Based Solid Phase Extraction.

    Science.gov (United States)

    Shirshekanb, Mahsa; Rezadoost, Hassan; Javanbakht, Mehran; Ghassempour, Ali Reza

    2017-01-01

    There is no other naturally occurring defense agent against cancer that has a stronger effect than paclitaxel, commonly known under the brand name of Taxol ® . The major drawback for the more widespread use of paclitaxel and its precious precursor, 10-deacetylbaccatin III (10-DAB III), is that they require large-scale extraction from different parts of yew trees ( Taxus species), cell cultures, taxane-producing endophytic fungi, and Corylus species. In our previous work, a novel online two-dimensional heart-cut liquid chromatography process using hydrophilic interaction/ reversed-phase chromatography was used to introduce a semi-preparative treatment for the separation of polar (10-deacetylbaccatin III) and non-polar (paclitaxel) taxanes from Taxus baccata L. In this work, a combination of the absorbent (Diaion ®  HP-20) and a silica based solid phase extraction is utilized as a new, efficient, and cost effective method for large-scale production of taxanes. This process avoids the technical problem of two-dimensional preparative liquid chromatography. The first stage of the process involves discarding co-extractive polar compounds including chlorophylls and pigments using a non-polar synthetic hydrophobic absorbent, Diaion ®  HP-20. Extract was then loaded on to a silica based hydrophilic interaction solid phase extraction (silica 40-60 micron). Taxanes was eluted using a mixture of water and methanol at the optimized ratio of 70:30. Finally, the fraction containing taxanes was applied to semi-preparative reversed phase HPLC. The results revealed that using this procedure, paclitaxel and 10-DAB III could be obtained at 8 and 3 times more, respectively than by the traditional method of extraction.

  10. The Combination Process for Preparative Separation and Purification of Paclitaxel and 10-Deacetylbaccatin III Using Diaion® Hp-20 Followed by Hydrophilic Interaction Based Solid Phase Extraction

    Science.gov (United States)

    Shirshekanb, Mahsa; Rezadoost, Hassan; Javanbakht, Mehran; Ghassempour, Ali Reza

    2017-01-01

    There is no other naturally occurring defense agent against cancer that has a stronger effect than paclitaxel, commonly known under the brand name of Taxol®. The major drawback for the more widespread use of paclitaxel and its precious precursor, 10-deacetylbaccatin III (10-DAB III), is that they require large-scale extraction from different parts of yew trees (Taxus species), cell cultures, taxane-producing endophytic fungi, and Corylus species. In our previous work, a novel online two-dimensional heart-cut liquid chromatography process using hydrophilic interaction/ reversed-phase chromatography was used to introduce a semi-preparative treatment for the separation of polar (10-deacetylbaccatin III) and non-polar (paclitaxel) taxanes from Taxus baccata L. In this work, a combination of the absorbent (Diaion® HP-20) and a silica based solid phase extraction is utilized as a new, efficient, and cost effective method for large-scale production of taxanes. This process avoids the technical problem of two-dimensional preparative liquid chromatography. The first stage of the process involves discarding co-extractive polar compounds including chlorophylls and pigments using a non-polar synthetic hydrophobic absorbent, Diaion® HP-20. Extract was then loaded on to a silica based hydrophilic interaction solid phase extraction (silica 40-60 micron). Taxanes was eluted using a mixture of water and methanol at the optimized ratio of 70:30. Finally, the fraction containing taxanes was applied to semi-preparative reversed phase HPLC. The results revealed that using this procedure, paclitaxel and 10-DAB III could be obtained at 8 and 3 times more, respectively than by the traditional method of extraction. PMID:29552048

  11. Adjuvant whole abdominal intensity modulated radiotherapy (IMRT) for high risk stage FIGO III patients with ovarian cancer (OVAR-IMRT-01) – Pilot trial of a phase I/II study: study protocol

    International Nuclear Information System (INIS)

    Rochet, Nathalie; Jensen, Alexandra D; Sterzing, Florian; Munter, Marc W; Eichbaum, Michael H; Schneeweiss, Andreas; Sohn, Christof; Debus, Juergen; Harms, Wolfgang

    2007-01-01

    The prognosis for patients with advanced epithelial ovarian cancer remains poor despite aggressive surgical resection and platinum-based chemotherapy. More than 60% of patients will develop recurrent disease, principally intraperitoneal, and die within 5 years. The use of whole abdominal irradiation (WAI) as consolidation therapy would appear to be a logical strategy given its ability to sterilize small tumour volumes. Despite the clinically proven efficacy of whole abdominal irradiation, the use of radiotherapy in ovarian cancer has profoundly decreased mainly due to high treatment-related toxicity. Modern intensity-modulated radiation therapy (IMRT) could allow to spare kidneys, liver, and bone marrow while still adequately covering the peritoneal cavity with a homogenous dose. The OVAR-IMRT-01 study is a single center pilot trial of a phase I/II study. Patients with advanced ovarian cancer stage FIGO III (R1 or R2< 1 cm) after surgical resection and platinum-based chemotherapy will be treated with whole abdomen irradiation as consolidation therapy using intensity modulated radiation therapy (IMRT) to a total dose of 30 Gy in 1.5 Gy fractions. A total of 8 patients will be included in this trial. For treatment planning bone marrow, kidneys, liver, spinal cord, vertebral bodies and pelvic bones are defined as organs at risk. The planning target volume includes the entire peritoneal cavity plus pelvic and para-aortic node regions. The primary endpoint of the study is the evaluation of the feasibility of intensity-modulated WAI and the evaluation of the study protocol. Secondary endpoint is evaluation of the toxicity of intensity modulated WAI before continuing with the phase I/II study. The aim is to explore the potential of IMRT as a new method for WAI to decrease the dose to kidneys, liver, bone marrow while covering the peritoneal cavity with a homogenous dose, and to implement whole abdominal intensity-modulated radiotherapy into the adjuvant multimodal

  12. Complexation of trivalent actinides and lanthanides with hydrophilic N-donor ligands for Am(III)/Cm(III) and An(III)/Ln(III) separation; Komplexierung von trivalenten Actiniden und Lanthaniden mit hydrophilen N-Donorliganden zur Am(III)/Cm(III)- bzw. An(III)/Ln(III)-Trennung

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Christoph

    2017-07-24

    The implementation of actinide recycling processes is considered in several countries, aiming at the reduction of long-term radiotoxicity and heat load of used nuclear fuel. This requires the separation of the actinides from the fission and corrosion products. The separation of the trivalent actinides (An(III)) Am(III) and Cm(III), however, is complicated by the presence of the chemically similar fission lanthanides (Ln(III)). Hydrophilic N-donor ligands are employed as An(III) or Am(III) selective complexing agents in solvent extraction to strip An(III) or Am(III) from an organic phase loaded with An(III) and Ln(III). Though they exhibit excellent selectivity, the complexation chemistry of these ligands and the complexes formed during solvent extraction are not sufficiently characterized. In the present thesis the complexation of An(III) and Ln(III) with hydrophilic N-donor ligands is studied by time resolved laser fluorescence spectroscopy (TRLFS), UV/Vis, vibronic sideband spectroscopy and solvent extraction. TRLFS studies on the complexation of Cm(III) and Eu(III) with the Am(III) selective complexing agent SO{sub 3}-Ph-BTBP (tetrasodium 3,3{sup '},3'',3{sup '''}-([2,2{sup '}-bipyridine]-6,6{sup '}-diylbis(1,2,4-triazine-3,5,6-triyl)) tetrabenzenesulfonate) revealed the formation of [M(SO{sub 3}-Ph-BTBP){sub n}]{sup (4n-3)-} complexes (M = Cm(III), Eu(III); n = 1, 2). The conditional stability constants were determined in different media yielding two orders of magnitude larger β{sub 2}-values for the Cm(III) complexes, independently from the applied medium. A strong impact of ionic strength on the stability and stoichiometry of the formed complexes was identified, resulting from the stabilization of the pentaanionic [M(SO{sub 3}-Ph-BTBP){sub 2}]{sup 5-} complex with increasing ionic strength. Thermodynamic studies of Cm(III)-SO{sub 3}-Ph-BTBP complexation showed that the proton concentration of the applied medium impacts

  13. Rituximab Maintenance Treatment of Relapsed/Resistant Follicular Non-Hodgkin's Lymphoma: Long-Term Outcome of the EORTC 20981 Phase III Randomized Intergroup Study

    NARCIS (Netherlands)

    van Oers, Marinus H. J.; van Glabbeke, Martine; Giurgea, Livia; Klasa, Richard; Marcus, Robert E.; Wolf, Max; Kimby, Eva; van 't Veer, Mars; Vranovsky, Andrej; Holte, Harald; Hagenbeek, Anton

    2010-01-01

    Purpose In 2006, we published the results of the European Organisation for Research and Treatment of Cancer phase III trial EORTC 20981 on the role of rituximab in remission induction and maintenance treatment of relapsed/resistant follicular lymphoma (FL). At that time, the median follow-up for the

  14. Evaluating Intermittent Androgen-Deprivation Therapy Phase III Clinical Trials: The Devil Is in the Details.

    Science.gov (United States)

    Hussain, Maha; Tangen, Catherine; Higano, Celestia; Vogelzang, Nicholas; Thompson, Ian

    2016-01-20

    Intermittent androgen deprivation (IAD) has been widely tested in prostate cancer. However, phase III trials testing continuous androgen deprivation (CAD) versus IAD have reached inconclusive and seemingly contradictory results. Different design and conduct issues must be critically evaluated to better interpret the results. Seven published phase III trials were examined for prespecified design and outcomes. Treatment specifications; primary end point; superiority versus noninferiority design assumptions, including magnitude of assumed versus observed noninferiority margin (NIM); duration of follow-up; and quality-of-life (QOL) outcomes were considered in terms of the results and conclusions reported. Five trials had a superiority and three had a noninferiority primary hypothesis. Only three trials had a uniform population and overall survival (OS) end point. All trials observed better outcomes in terms of OS and progression-free survival (PFS) than assumed at time of study design, translating into prespecified NIMs or hazard ratios that reflected larger absolute differences in OS or PFS between arms. Lower-than-expected event rates also reduced statistical power for the trials. Other factors, including length of follow-up, cause of death, QOL, and primary end point, and their impact on trial interpretation are discussed. No trial to date has demonstrated survival superiority of IAD compared with CAD. Trials concluding IAD is noninferior to CAD were based on wide NIMs that included clinically important survival differences, not likely to be considered comparable by physicians or patients. Interim analyses relying on short follow-up and including a majority of non-prostate cancer deaths will favor a noninferiority conclusion and should be interpreted cautiously. Adequate follow-up is required to ensure capture of prostate cancer deaths in both superiority and noninferiority trials. © 2015 by American Society of Clinical Oncology.

  15. Coping with missing data in phase III pivotal registration trials: Tolvaptan in subjects with kidney disease, a case study.

    Science.gov (United States)

    Ouyang, John; Carroll, Kevin J; Koch, Gary; Li, Junfang

    2017-07-01

    Missing data cause challenging issues, particularly in phase III registration trials, as highlighted by the European Medicines Agency (EMA) and the US National Research Council. We explore, as a case study, how the issues from missing data were tackled in a double-blind phase III trial in subjects with autosomal dominant polycystic kidney disease. A total of 1445 subjects were randomized in a 2:1 ratio to receive active treatment (tolvaptan), or placebo. The primary outcome, the rate of change in total kidney volume, favored tolvaptan (P outline the analyses undertaken to address the issue of missing data thoroughly. "Tipping point analyses" were performed to explore how extreme and detrimental outcomes among subjects with missing data must be to overturn the positive treatment effect attained in those subjects who had complete data. Nonparametric rank-based analyses were also performed accounting for missing data. In conclusion, straightforward and transparent analyses directly taking into account missing data convincingly support the robustness of the preplanned analyses on the primary and secondary endpoints. Tolvaptan was confirmed to be effective in slowing total kidney volume growth, which is considered an efficacy endpoint by EMA, and in lessening the decline in renal function in patients with autosomal dominant polycystic kidney disease. Copyright © 2017 John Wiley & Sons, Ltd.

  16. Effects of Mg/Ga and V/III source ratios on hole concentration of N-polar (000\\bar{1}) p-type GaN grown by metalorganic vapor phase epitaxy

    Science.gov (United States)

    Nonoda, Ryohei; Shojiki, Kanako; Tanikawa, Tomoyuki; Kuboya, Shigeyuki; Katayama, Ryuji; Matsuoka, Takashi

    2016-05-01

    The effects of growth conditions such as Mg/Ga and V/III ratios on the properties of N-polar (000\\bar{1}) p-type GaN grown by metalorganic vapor phase epitaxy were studied. Photoluminescence spectra from Mg-doped GaN depended on Mg/Ga and V/III ratios. For the lightly doped samples, the band-to-acceptor emission was observed at 3.3 eV and its relative intensity decreased with increasing V/III ratio. For the heavily doped samples, the donor-acceptor pair emission was observed at 2.8 eV and its peak intensity monotonically decreased with V/III ratio. The hole concentration was maximum for the Mg/Ga ratio. This is the same tendency as in group-III polar (0001) growth. The V/III ratio also reduced the hole concentration. The higher V/III ratio reduced the concentration of residual donors such as oxygen by substituting nitrogen atoms. The surface became rougher with increasing V/III ratio and the hillock density increased.

  17. New analogues of Cucurbita maxima trypsin inhibitor III (CMTI III) with simplified structure.

    Science.gov (United States)

    Rolka, K; Kupryszewski, G; Rózycki, J; Ragnarsson, U; Zbyryt, T; Otlewski, J

    1992-10-01

    Seven new analogues of trypsin inhibitor CMTI III were obtained by solid-phase peptide synthesis. Three analogues contained only two, instead of three, disulfide bridges, whereas the molecules of the next four analogues were shortened at the N- and/or C-terminus. The elimination of one disulfide bridge in CMTI III induces a decrease in the association equilibrium constants by 6-7 orders of magnitude, whereas the removal of one, two or three amino-acid residues at the N- and/or C-terminus does not significantly affect the activity.

  18. Solid phase extraction of Am(III) and Cm(III) from acidic feeds using tetraethyl diglycolamide (TEDGA) in ionic liquid

    NARCIS (Netherlands)

    Gujar, R.B.; Ansari, S.A.; Mohapatra, P.K.; Leoncini, Andrea; Verboom, Willem

    2016-01-01

    Solvent extraction of Am(III) and Cm(III) with several diglycolamide ligands in an ionic liquid, [C4mim][Tf2N] was investigated from nitric acid medium. Based on the encouraging extraction behaviour with N,N,N′,N′-tetraethyldiglycolamide (TEDGA), extraction chromatographic studies were carried out

  19. Integrated safety analysis of rolapitant with coadministered drugs from phase II/III trials

    DEFF Research Database (Denmark)

    Barbour, S; Smit, T.; Wang, X

    2017-01-01

    adverse events by use versus non-use of drug substrates of CYP2D6 or BCRP. Patients and methods: Patients were randomized to receive either 180 mg oral rolapitant or placebo approximately 1-2 hours before chemotherapy in combination with a 5-hydroxytryptamine type 3 RA and dexamethasone. Data...... cytochrome P450 (CYP) 3A4, but it does inhibit CYP2D6 and breast cancer resistance protein (BCRP). To analyze potential drug-drug interactions between rolapitant and concomitant medications, this integrated safety analysis of four double-blind, randomized phase II or III studies of rolapitant examined...... for treatment-emergent adverse events (TEAEs) and treatment-emergent serious adverse events (TESAEs) during cycle 1 were pooled across the four studies and summarized in the overall population and by concomitant use/non-use of CYP2D6 or BCRP substrate drugs. Results: In the integrated safety population, 828...

  20. Uptake Of Trivalent Actinides (Cm(III)) And Lanthanides (Eu(III)) By Cement-Type Minerals: A Wet Chemistry And Time-Resolved Laser Fluorescence Spectroscopy (TRLFS) Study

    Energy Technology Data Exchange (ETDEWEB)

    Tits, J.; Stumpf, T; Wieland, E.; Fanghaenel, T

    2003-03-01

    The interaction of the two chemical homologues Cm (III) and Eu(III) with calcium silicate hydrates at pH 13.3 has been investigated in batch-type sorption studies using Eu(III), and complemented with time-resolved laser fluorescence spectroscopy using Cm(III). The sorption data for Eu(III) reveal fast sorption kinetics, and a strong uptake by CSH phases, with distribution ratios of 6({+-}3)*105 L kg-1. Three different types of sorbed Cm(III) species have been identified: a non-fluorescing species, which was identified as Cm cluster present either as surface precipitate or as Cm(III) colloid in solution, and two sorbed fluorescing species. The sorbed fluorescing species have characteristic emission spectra (main peak maxima at 618.9 nm and 620.9 nm) and fluorescence emission lifetimes (289 {+-} 11 ms and 1482{+-} 200 ms). From the fluorescence lifetimes, it appears that the two fluorescing Cm(III) species have, respectively, one to two or no water molecules left in their first coordination sphere, suggesting that these species are incorporated into the CSH structure. A structural model for Cm(III) and Eu(III) incorporation into CSH phases is proposed based on the substitution of Ca at two different types of sites in the CSH structure. (author)

  1. Should positive phase III clinical trial data be required before proton beam therapy is more widely adopted? No

    International Nuclear Information System (INIS)

    Suit, Herman; Kooy, Hanne; Trofimov, Alexei; Farr, Jonathan; Munzenrider, John; DeLaney, Thomas; Loeffler, Jay; Clasie, Benjamin; Safai, Sairos; Paganetti, Harald

    2008-01-01

    Purpose: Evaluate the rationale for the proposals that prior to a wider use of proton radiation therapy there must be supporting data from phase III clinical trials. That is, would less dose to normal tissues be an advantage to the patient? Methods: Assess the basis for the assertion that proton dose distributions are superior to those of photons for most situations. Consider the requirements for determining the risks of normal tissue injury, acute and remote, in the examination of the data from a trial. Analyze the probable cost differential between high technology photon and proton therapy. Evaluate the rationale for phase III clinical trials of proton vs photon radiation therapy when the only difference in dose delivered is a difference in distribution of low LET radiation. Results: The distributions of biological effective dose by protons are superior to those by X-rays for most clinical situations, viz. for a defined dose and dose distribution to the target by protons there is a lower dose to non-target tissues. This superiority is due to these physical properties of protons: (1) protons have a finite range and that range is exclusively dependent on the initial energy and the density distribution along the beam path; (2) the Bragg peak; (3) the proton energy distribution may be designed to provide a spread out Bragg peak that yields a uniform dose across the target volume and virtually zero dose deep to the target. Importantly, proton and photon treatment plans can employ beams in the same number and directions (coplanar, non-co-planar), utilize intensity modulation and employ 4D image guided techniques. Thus, the only difference between protons and photons is the distribution of biologically effective dose and this difference can be readily evaluated and quantified. Additionally, this dose distribution advantage should increase the tolerance of certain chemotherapeutic agents and thus permit higher drug doses. The cost of service (not developmental) proton

  2. Structural systematics of rare earth complexes. III. Structural characterization of lanthanoid (III) picrate hydrates: gadolinium picrate dodecahydrate - an x-ray-induced phase modifications? - and some general aspects of structural chemistry of lanthanoid picrates

    International Nuclear Information System (INIS)

    Harrowfield, J.M.; Weimin, Lu; Brian, W.S.; White, A.H.

    1994-01-01

    In the course of the previous studies (Parts I and II), an unusual result was observed in the case of the structure determination of hydrated gadolinium(III) picrate. Midway through data collection, the monoclinic P2 1 /c phase modification (X-ray-induced?) to a similar cell more nearly resembling that of the La→Pr structure type recorded previously, with no loss of crystal integrity, and with useful data sets being obtained on both forms. Redetermination of the structure with a fresh sample yielded no reproduction of the anomaly. These results are recorded and discussed, together with an overview of the consequences of the data of Parts I-III in relation to those of other literature in the field. 13 refs., 4 tabs., 1 fig

  3. A quality assurance audit: phase III trial of maximal androgen deprivation in prostate cancer (TROG 96.01).

    Science.gov (United States)

    Steigler, A; Mameghan, H; Lamb, D; Joseph, D; Matthews, J; Franklin, I; Turner, S; Spry, N; Poulsen, M; North, J; Kovacev, O; Denham, J

    2000-02-01

    In 1997 the Trans-Tasman Radiation Oncology Group (TROG) performed a quality assurance (QA) audit of its phase III randomized clinical trial investigating the effectiveness of different durations of maximal androgen deprivation prior to and during definitive radiation therapy for locally advanced carcinoma of the prostate (TROG 96.01). The audit reviewed a total of 60 cases from 15 centres across Australia and New Zealand. In addition to verification of technical adherence to the protocol, the audit also incorporated a survey of centre planning techniques and a QA time/cost analysis. The present report builds on TROG's first technical audit conducted in 1996 for the phase III accelerated head and neck trial (TROG 91.01) and highlights the significant progress TROG has made in the interim period. The audit provides a strong validation of the results of the 96.01 trial, as well as valuable budgeting and treatment planning information for future trials. Overall improvements were detected in data quality and quantity, and in protocol compliance, with a reduction in the rate of unacceptable protocol violations from 10 to 4%. Audit design, staff education and increased data management resources were identified as the main contributing factors to these improvements. In addition, a budget estimate of $100 per patient has been proposed for conducting similar technical audits. The next major QA project to be undertaken by TROG during the period 1998-1999 is an intercentre dosimetry study. Trial funding and staff education have been targeted as the key major issues essential to the continued success and expansion of TROG's QA programme.

  4. Position-controlled epitaxial III-V nanowires on silicon

    NARCIS (Netherlands)

    Roest, A.L.; Verheijen, M.A.; Wunnicke, O.; Serafin, S.N.; Wondergem, H.J.; Bakkers, E.P.A.M.

    2006-01-01

    We show the epitaxial integration of III-V semiconductor nanowires with silicon technology. The wires are grown by the VLS mechanism with laser ablation as well as metal-organic vapour phase epitaxy. The hetero-epitaxial growth of the III-V nanowires on silicon was confirmed with x-ray diffraction

  5. Growth, structure and phase transitions of epitaxial nanowires of III-V semiconductors

    International Nuclear Information System (INIS)

    Glas, F; Patriarche, G; Harmand, J C

    2010-01-01

    We review and illustrate the impact of TEM on the study of nanowires of non-nitride III-V semiconductors, with particular emphasis on the understanding of the thermodynamics and kinetics of their formation assisted by nano-sized catalyst particles. Besides providing basic information about the morphology of the nanowires and their growth rate as a function of diameter, TEM offers insights into the peculiar crystalline structure that they adopt. We discuss the formation of the unusual wurtzite hexagonal crystalline phase and that of planar stacking defects in these nanowires and show that they are kinetically controlled. We also demonstrate the transformation of wurtzite into cubic sphalerite upon epitaxial burying of the nanowires. Nanowires are particularly interesting in that they allow the fabrication of precisely positioned quantum dots with well-defined geometries. In this respect, we discuss the formation of strained quantum-size inclusions in nanowires, their critical dimensions and the kinetic and thermodynamic factors governing the changes of the crystalline structure that sometimes occur around a hetero-interface.

  6. Impact of Dengue Vaccination on Serological Diagnosis: Insights From Phase III Dengue Vaccine Efficacy Trials.

    Science.gov (United States)

    Plennevaux, Eric; Moureau, Annick; Arredondo-García, José L; Villar, Luis; Pitisuttithum, Punnee; Tran, Ngoc H; Bonaparte, Matthew; Chansinghakul, Danaya; Coronel, Diana L; L'Azou, Maïna; Ochiai, R Leon; Toh, Myew-Ling; Noriega, Fernando; Bouckenooghe, Alain

    2018-04-03

    We previously reported that vaccination with the tetravalent dengue vaccine (CYD-TDV; Dengvaxia) may bias the diagnosis of dengue based on immunoglobulin M (IgM) and immunoglobulin G (IgG) assessments. We undertook a post hoc pooled analysis of febrile episodes that occurred during the active surveillance phase (the 25 months after the first study injection) of 2 pivotal phase III, placebo-controlled CYD-TDV efficacy studies that involved ≥31000 children aged 2-16 years across 10 countries in Asia and Latin America. Virologically confirmed dengue (VCD) episode was defined with a positive test for dengue nonstructural protein 1 antigen or dengue polymerase chain reaction. Probable dengue episode was serologically defined as (1) IgM-positive acute- or convalescent-phase sample, or (2) IgG-positive acute-phase sample and ≥4-fold IgG increase between acute- and convalescent-phase samples. There were 1284 VCD episodes (575 and 709 in the CYD-TDV and placebo groups, respectively) and 17673 other febrile episodes (11668 and 6005, respectively). Compared with VCD, the sensitivity and specificity of probable dengue definition were 93.1% and 77.2%, respectively. Overall positive and negative predictive values were 22.9% and 99.5%, respectively, reflecting the much lower probability of correctly confirming probable dengue in a population including a vaccinated cohort. Vaccination-induced bias toward false-positive diagnosis was more pronounced among individuals seronegative at baseline. Caution will be required when interpreting IgM and IgG data obtained during routine surveillance in those vaccinated with CYD-TDV. There is an urgent need for new practical, dengue-specific diagnostic algorithms now that CYD-TDV is approved in a number of dengue-endemic countries. NCT01373281 and NCT01374516.

  7. Cloud point extraction: an alternative to traditional liquid-liquid extraction for lanthanides(III) separation.

    Science.gov (United States)

    Favre-Réguillon, Alain; Draye, Micheline; Lebuzit, Gérard; Thomas, Sylvie; Foos, Jacques; Cote, Gérard; Guy, Alain

    2004-06-17

    Cloud point extraction (CPE) was used to extract and separate lanthanum(III) and gadolinium(III) nitrate from an aqueous solution. The methodology used is based on the formation of lanthanide(III)-8-hydroxyquinoline (8-HQ) complexes soluble in a micellar phase of non-ionic surfactant. The lanthanide(III) complexes are then extracted into the surfactant-rich phase at a temperature above the cloud point temperature (CPT). The structure of the non-ionic surfactant, and the chelating agent-metal molar ratio are identified as factors determining the extraction efficiency and selectivity. In an aqueous solution containing equimolar concentrations of La(III) and Gd(III), extraction efficiency for Gd(III) can reach 96% with a Gd(III)/La(III) selectivity higher than 30 using Triton X-114. Under those conditions, a Gd(III) decontamination factor of 50 is obtained.

  8. Randomized phase III study comparing paclitaxel/cisplatin/gemcitabine and gemcitabine/cisplatin in patients with locally advanced or metastatic urothelial cancer without prior systemic therapy

    DEFF Research Database (Denmark)

    Bellmunt, Joaquim; von der Maase, Hans; Mead, Graham M

    2012-01-01

    The combination of gemcitabine plus cisplatin (GC) is a standard regimen in patients with locally advanced or metastatic urothelial cancer. A phase I/II study suggested that a three-drug regimen that included paclitaxel had greater antitumor activity and might improve survival....

  9. CMPO-calix[4]arenes and the influence of structural modifications on the Eu(III), Am(III), Cm(III) separation

    International Nuclear Information System (INIS)

    Peters, C.; Braekers, D.; Desreux, J.F.; Kasyan, O.; Miroshnichenko, S.; Rudzevich, V.; Boehmer, V.

    2008-01-01

    The syntheses of new calix[4]arenes featuring CMPO groups on the wide rim are reported and the extraction of Am(III) and Eu(III) from concentrated HNO 3 aqueous phases are discussed with reference to the properties of the symmetric tetra-CMPO derivative 1. All extraction studies were conducted in the same experimental conditions which allows to directly compare the dependence of the distribution coefficients of various calixarenes on the acid concentration (0.1 M 3 ] < 5 M). Calix[4]arene 1 becomes a very poor extractant if the length of the aliphatic chain between the amide and phosphine oxide groups of CMPO is increased, if the bridging methylene groups are replaced by sulfur atoms or if the macrocyclic cavity size is increased. By contrast, mixed amide - CMPO calix[4]arenes are nearly as effective than 1. Moreover, Am(III)/Cm(III) separation coefficients between 1.5 and 3 have been obtained with unsymmetrical calix[4]arenes of type 1 with different aliphatic chains grafted on the narrow rim. Guidelines to anticipate the extraction ability of calix[4]arenes remain elusive because of the intricate solution behavior of these compounds. (orig.)

  10. Oxidation of Cr(III)-Fe(III) Mixed-phase Hydroxides by Chlorine: Implications on the Control of Hexavalent Chromium in Drinking Water.

    Science.gov (United States)

    Chebeir, Michelle; Liu, Haizhou

    2018-05-17

    The occurrence of chromium (Cr) as an inorganic contaminant in drinking water is widely reported. One source of Cr is its accumulation in iron-containing corrosion scales of drinking water distribution systems as Cr(III)-Fe(III) hydroxide, i.e., FexCr(1-x)(OH)3(s), where x represents the Fe(III) molar content and typically varies between 0.25 and 0.75. This study investigated the kinetics of inadvertent hexavalent chromium Cr(VI) formation via the oxidation of FexCr(1-x)(OH)3(s) by chlorine as a residual disinfectant in drinking water, and examined the impacts of Fe(III) content and drinking water chemical parameters including pH, bromide and bicarbonate on the rate of Cr(VI) formation. Data showed that an increase in Fe(III) molar content resulted in a significant decrease in the stoichiometric Cr(VI) yield and the rate of Cr(VI) formation, mainly due to chlorine decay induced by Fe(III) surface sites. An increase in bicarbonate enhanced the rate of Cr(VI) formation, likely due to the formation of Fe(III)-carbonato surface complexes that slowed down the scavenging reaction with chlorine. The presence of bromide significantly accelerated the oxidation of FexCr(1-x)(OH)3(s) by chlorine, resulting from the catalytic effect of bromide acting as an electron shuttle. A higher solution pH between 6 and 8.5 slowed down the oxidation of Cr(III) by chlorine. These findings suggested that the oxidative conversion of chromium-containing iron corrosion products in drinking water distribution systems can lead to the occurrence of Cr(VI) at the tap, and the abundance of iron, and a careful control of pH, bicarbonate and bromide levels can assist the control of Cr(VI) formation.

  11. Objective Lightning Probability Forecasting for Kennedy Space Center and Cape Canaveral Air Force Station, Phase III

    Science.gov (United States)

    Crawford, Winifred C.

    2010-01-01

    The AMU created new logistic regression equations in an effort to increase the skill of the Objective Lightning Forecast Tool developed in Phase II (Lambert 2007). One equation was created for each of five sub-seasons based on the daily lightning climatology instead of by month as was done in Phase II. The assumption was that these equations would capture the physical attributes that contribute to thunderstorm formation more so than monthly equations. However, the SS values in Section 5.3.2 showed that the Phase III equations had worse skill than the Phase II equations and, therefore, will not be transitioned into operations. The current Objective Lightning Forecast Tool developed in Phase II will continue to be used operationally in MIDDS. Three warm seasons were added to the Phase II dataset to increase the POR from 17 to 20 years (1989-2008), and data for October were included since the daily climatology showed lightning occurrence extending into that month. None of the three methods tested to determine the start of the subseason in each individual year were able to discern the start dates with consistent accuracy. Therefore, the start dates were determined by the daily climatology shown in Figure 10 and were the same in every year. The procedures used to create the predictors and develop the equations were identical to those in Phase II. The equations were made up of one to three predictors. TI and the flow regime probabilities were the top predictors followed by 1-day persistence, then VT and Ll. Each equation outperformed four other forecast methods by 7-57% using the verification dataset, but the new equations were outperformed by the Phase II equations in every sub-season. The reason for the degradation may be due to the fact that the same sub-season start dates were used in every year. It is likely there was overlap of sub-season days at the beginning and end of each defined sub-season in each individual year, which could very well affect equation

  12. Targeting radioimmunotherapy of hepatocellular carcinoma with iodine (131I) metuximab injection: Clinical Phase I/II trials

    International Nuclear Information System (INIS)

    Chen Zhinan; Mi Li; Xu Jing

    2006-01-01

    Purpose: HAb18G/CD147 is a hepatocellular carcinoma (HCC)-associated antigen. We developed iodine ( 131 I) metuximab injection (Licartin), a novel 131 I-labeled HAb18G/CD147-specific monoclonal antibody F(ab') 2 fragment, and evaluated its safety, pharmacokinetics, and clinical efficacy on HCC in Phase I/II trials. Methods and Materials: In a Phase I trial, 28 patients were randomly assigned to receive the injection in 9.25-, 18.5-, 27.75-, or 37-MBq/kg doses by hepatic artery infusion. In a multicenter Phase II trial, 106 patients received the injection (27.75 MBq/kg) on Day 1 of a 28-day cycle. Response rate and survival rate were the endpoints. Results: No life-threatening toxic effects were found. The safe dosage was 27.75 MBq/kg. The blood clearance fitted a biphasic model, and its half-life was 90.56-63.93 h. In the Phase II trial, the injection was found to be targeted and concentrated to tumor tissues. Of the 73 patients completing two cycles, 6 (8.22%) had a partial response, 14 (19.18%) minor response, and 43 (58.90%) stable disease. The 21-month survival rate was 44.54%. The survival rate of progression-free patients was significantly higher than that of patients with progressive disease after either one or two cycles (p 131 I) metuximab injection is safe and active for HCC patients

  13. Phase III trial of casopitant, a novel neurokinin-1 receptor antagonist, for the prevention of nausea and vomiting in patients receiving moderately emetogenic chemotherapy

    DEFF Research Database (Denmark)

    Herrstedt, Jørn; Apornwirat, Wichit; Shaharyar, Ahmed

    2009-01-01

    PURPOSE: The purpose of this phase III trial was to evaluate the efficacy and safety of regimens containing casopitant, a novel neurokinin-1 receptor antagonist, for the prevention of chemotherapy-induced nausea and vomiting during the first cycle in patients receiving moderately emetogenic chemo...

  14. Phase III trial of high and low dose rate interstitial radiotherapy for early oral tongue cancer

    International Nuclear Information System (INIS)

    Inoue, Takehiro; Inoue, Toshihiko; Teshima, Teruki; Murayama, Shigeyuki; Shimizutani, Kimishige; Fuchihata, Hajime; Furukawa, Souhei

    1996-01-01

    Purpose: Oral tongue carcinomas are highly curable with radiotherapy. In the past, patients with tongue carcinoma have usually been treated with low dose rate (LDR) interstitial radiation. This Phase III study was designed to compare the treatment results obtained with LDR with those obtained with high dose rate (HDR) interstitial radiotherapy for tongue carcinoma. Methods and Materials: The criteria for patient selection for the Phase III study were: (a) presence of a T1T2N0 tumor that could be treated with single-plane implantation, (b) localization of tumor at the lateral tongue border, (c) tumor thickness of 10 mm or less, (d) performance status between O and 3, and (e) absence of any severe concurrent disease. From April 1992 through December 1993, 15 patients in the LDR group (70 Gy/4 to 9 days) and 14 patients in the HDR group (60 Gy/10 fractions/6 days) were accrued. The time interval between two fractions of the HDR brachytherapy was more than 6 h. Results: Local recurrence occurred in two patients treated with LDR brachytherapy but in none of the patients treated with HDR. One- and 2-year local control rates for patients in the LDR group were both 86%, compared with 100% in the HDR group (p = 0.157). There were four patients with nodal metastasis in the LDR group and three in the HDR group. Local recurrence occurred in two of the four patients with nodal metastases in the LDR group. One- and 2-year nodal control rates for patients in the LDR group are were 85%, compared with 79% in the HDR group. Conclusion: HDR fractionated interstitial brachytherapy can be an alternative to traditional LDR brachytherapy for early tongue cancer and eliminate the radiation exposure for medical staffs

  15. Obtaining valid laboratory data in clinical trials conducted in resource diverse settings: lessons learned from a microbicide phase III clinical trial.

    Directory of Open Access Journals (Sweden)

    Tania Crucitti

    2010-10-01

    Full Text Available Over the last decade several phase III microbicides trials have been conducted in developing countries. However, laboratories in resource constrained settings do not always have the experience, infrastructure, and the capacity to deliver laboratory data meeting the high standards of clinical trials. This paper describes the design and outcomes of a laboratory quality assurance program which was implemented during a phase III clinical trial evaluating the efficacy of the candidate microbicide Cellulose Sulfate 6% (CS [1].In order to assess the effectiveness of CS for HIV and STI prevention, a phase III clinical trial was conducted in 5 sites: 3 in Africa and 2 in India. The trial sponsor identified an International Central Reference Laboratory (ICRL, responsible for the design and management of a quality assurance program, which would guarantee the reliability of laboratory data. The ICRL provided advice on the tests, assessed local laboratories, organized trainings, conducted supervision visits, performed re-tests, and prepared control panels. Local laboratories were provided with control panels for HIV rapid tests and Chlamydia trachomatis/Neisseria gonorrhoeae (CT/NG amplification technique. Aliquots from respective control panels were tested by local laboratories and were compared with results obtained at the ICRL.Overall, good results were observed. However, discordances between the ICRL and site laboratories were identified for HIV and CT/NG results. One particular site experienced difficulties with HIV rapid testing shortly after study initiation. At all sites, DNA contamination was identified as a cause of invalid CT/NG results. Both problems were timely detected and solved. Through immediate feedback, guidance and repeated training of laboratory staff, additional inaccuracies were prevented.Quality control guidelines when applied in field laboratories ensured the reliability and validity of final study data. It is essential that sponsors

  16. A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

    Energy Technology Data Exchange (ETDEWEB)

    Pancake, Daniel; Rock, Cynthia M.; Creed, Richard [Argonne National Laboratory, 9700 South Cass Avenue, Lemont, IL 60439 (United States); Donohoue, Tom; Martin, E. Ray; Mason, John A. [ANTECH Corporation 9050 Marshall Court, Westminster, CO, 80031 (United States); Norton, Christopher J.; Crosby, Daniel [Environmental Alternatives, Inc., 149 Emerald Street, Suite R, Keene, NH 03431 (United States); Nachtman, Thomas J. [InstaCote, Inc., 160 C. Lavoy Road, Erie, MI, 48133 (United States)

    2013-07-01

    This paper describes the process of decommissioning two gloveboxes at the Argonne National Laboratory (ANL) that were employed for work with plutonium and other radioactive materials. The decommissioning process involved an initial phase of clearing tools and materials from the glove boxes and disconnecting them from the laboratory infrastructure. The removed materials, assessed as Transuranic (TRU) waste, were packaged into 55 gallon (200 litre) drums and prepared for ultimate disposal at the Waste Isolation Pilot Plant (WIPP) at Carlsbad New Mexico. The boxes were then sampled to determine the radioactive contents by means of smears that were counted with alpha and beta detectors to determine the residual surface contamination, especially in terms of alpha particle emitters that are an indicator of TRU activity. Paint chip samples were also collected and sent for laboratory analysis in order to ascertain the radioactive contamination contributing to the TRU activity as a fixed contamination. The investigations predicted that it may be feasible to reduce the residual surface contamination and render the glovebox structure low level waste (LLW) for disposal. In order to reduce the TRU activity a comprehensive decontamination process was initiated using chemical compounds that are particularly effective for lifting and dissolving radionuclides that adhere to the inner surfaces of the gloveboxes. The result of the decontamination process was a reduction in the TRU surface activity on the inner surfaces of the gloveboxes by four orders of magnitude in terms of disintegrations per unit area (DPA). The next phase of the process involved a comprehensive assay of the gloveboxes using a combination of passive neutron and gamma ray scintillation detectors and a shielded and collimated high purity Germanium (HPGe) gamma ray detector. The HPGe detector was used to obtain gamma ray spectra for a variety of measurement positions within the glovebox. The spectra were used to

  17. A Novel and Cost Effective Approach to the Decommissioning and Decontamination of Legacy Glove Boxes - Minimizing TRU Waste and Maximizing LLW Waste - 13634

    International Nuclear Information System (INIS)

    Pancake, Daniel; Rock, Cynthia M.; Creed, Richard; Donohoue, Tom; Martin, E. Ray; Mason, John A.; Norton, Christopher J.; Crosby, Daniel; Nachtman, Thomas J.

    2013-01-01

    This paper describes the process of decommissioning two gloveboxes at the Argonne National Laboratory (ANL) that were employed for work with plutonium and other radioactive materials. The decommissioning process involved an initial phase of clearing tools and materials from the glove boxes and disconnecting them from the laboratory infrastructure. The removed materials, assessed as Transuranic (TRU) waste, were packaged into 55 gallon (200 litre) drums and prepared for ultimate disposal at the Waste Isolation Pilot Plant (WIPP) at Carlsbad New Mexico. The boxes were then sampled to determine the radioactive contents by means of smears that were counted with alpha and beta detectors to determine the residual surface contamination, especially in terms of alpha particle emitters that are an indicator of TRU activity. Paint chip samples were also collected and sent for laboratory analysis in order to ascertain the radioactive contamination contributing to the TRU activity as a fixed contamination. The investigations predicted that it may be feasible to reduce the residual surface contamination and render the glovebox structure low level waste (LLW) for disposal. In order to reduce the TRU activity a comprehensive decontamination process was initiated using chemical compounds that are particularly effective for lifting and dissolving radionuclides that adhere to the inner surfaces of the gloveboxes. The result of the decontamination process was a reduction in the TRU surface activity on the inner surfaces of the gloveboxes by four orders of magnitude in terms of disintegrations per unit area (DPA). The next phase of the process involved a comprehensive assay of the gloveboxes using a combination of passive neutron and gamma ray scintillation detectors and a shielded and collimated high purity Germanium (HPGe) gamma ray detector. The HPGe detector was used to obtain gamma ray spectra for a variety of measurement positions within the glovebox. The spectra were used to

  18. Pseudo Class III malocclusion

    Directory of Open Access Journals (Sweden)

    Fadia M. Al-Hummayani

    2016-04-01

    Full Text Available The treatment of deep anterior crossbite is technically challenging due to the difficulty of placing traditional brackets with fixed appliances. This case report represents a none traditional treatment modality to treat deep anterior crossbite in an adult pseudo class III malocclusion complicated by severely retruded, supraerupted upper and lower incisors. Treatment was carried out in 2 phases. Phase I treatment was performed by removable appliance “modified Hawley appliance with inverted labial bow,” some modifications were carried out to it to suit the presented case. Positive overbite and overjet was accomplished in one month, in this phase with minimal forces exerted on the lower incisors. Whereas, phase II treatment was performed with fixed appliances (braces to align teeth and have proper over bite and overjet and to close posterior open bite, this phase was accomplished within 11 month.

  19. Bleeding and infection with external ventricular drainage: a systematic review in comparison with adjudicated adverse events in the ongoing Clot Lysis Evaluating Accelerated Resolution of Intraventricular Hemorrhage Phase III (CLEAR-III IHV) trial.

    Science.gov (United States)

    Dey, Mahua; Stadnik, Agnieszka; Riad, Fady; Zhang, Lingjiao; McBee, Nichol; Kase, Carlos; Carhuapoma, J Ricardo; Ram, Malathi; Lane, Karen; Ostapkovich, Noeleen; Aldrich, Francois; Aldrich, Charlene; Jallo, Jack; Butcher, Ken; Snider, Ryan; Hanley, Daniel; Ziai, Wendy; Awad, Issam A

    2015-03-01

    Retrospective series report varied rates of bleeding and infection with external ventricular drainage (EVD). There have been no prospective studies of these risks with systematic surveillance, threshold definitions, or independent adjudication. To analyze the rate of complications in the ongoing Clot Lysis: Evaluating Accelerated Resolution of Intraventricular Hemorrhage Phase III (CLEAR III) trial, providing a comparison with a systematic review of complications of EVD in the literature. Patients were prospectively enrolled in the CLEAR III trial after placement of an EVD for obstructive intraventricular hemorrhage and randomized to receive recombinant tissue-type plasminogen activator or placebo. We counted any detected new hemorrhage (catheter tract hemorrhage or any other distant hemorrhage) on computed tomography scan within 30 days from the randomization. Meta-analysis of published series of EVD placement was compiled with STATA software. Growing or unstable hemorrhage was reported as a cause of exclusion from the trial in 74 of 5707 cases (1.3%) screened for CLEAR III. The first 250 patients enrolled have completed adjudication of adverse events. Forty-two subjects (16.8%) experienced ≥1 new bleeds or expansions, and 6 of 250 subjects (2.4%) suffered symptomatic hemorrhages. Eleven cases (4.4%) had culture-proven bacterial meningitis or ventriculitis. Risks of bleeding and infection in the ongoing CLEAR III trial are comparable to those previously reported in EVD case series. In the present study, rates of new bleeds and bacterial meningitis/ventriculitis are very low despite multiple daily injections, blood in the ventricles, the use of thrombolysis in half the cases, and generalization to >60 trial sites.

  20. Crystal Growth of New Radiation Detector Materials in Microgravity, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — RMD proposes to conduct a series of crystal growth experiments on the International Space Station in the SUBSA furnace inside the MSG glovebox to grow crystals of...

  1. Trends in heteroepitaxy of III-Vs on silicon for photonic and photovoltaic applications

    Science.gov (United States)

    Lourdudoss, Sebastian; Junesand, Carl; Kataria, Himanshu; Metaferia, Wondwosen; Omanakuttan, Giriprasanth; Sun, Yan-Ting; Wang, Zhechao; Olsson, Fredrik

    2017-02-01

    We present and compare the existing methods of heteroepitaxy of III-Vs on silicon and their trends. We focus on the epitaxial lateral overgrowth (ELOG) method as a means of achieving good quality III-Vs on silicon. Initially conducted primarily by near-equilibrium epitaxial methods such as liquid phase epitaxy and hydride vapour phase epitaxy, nowadays ELOG is being carried out even by non-equilibrium methods such as metal organic vapour phase epitaxy. In the ELOG method, the intermediate defective seed and the mask layers still exist between the laterally grown purer III-V layer and silicon. In a modified ELOG method called corrugated epitaxial lateral overgrowth (CELOG) method, it is possible to obtain direct interface between the III-V layer and silicon. In this presentation we exemplify some recent results obtained by these techniques. We assess the potentials of these methods along with the other existing methods for realizing truly monolithic photonic integration on silicon and III-V/Si heterojunction solar cells.

  2. A Phase I-II dose escalation study of fixed-dose rate gemcitabine, oxaliplatin and capecitabine every two weeks in advanced cholangiocarcinomas

    DEFF Research Database (Denmark)

    Lassen, Ulrik V; Jensen, Lars Henrik; Sorensen, Morten

    2011-01-01

    (O) and capecitabine (C), and evaluate the safety and efficacy of this regimen in patients with advanced cholangiocarcinoma (CC). Methods. In the Phase I part of the study a dose-escalation schedule of FDR G, O and C, administered every two weeks, was performed in patients with solid tumours...... and no other treatments or advanced CC. In the Phase II part response rate, toxicity, progression-free survival (PFS) and overall survival was evaluated in patients with newly diagnosed advanced CC. Results. Thirty-six patients entered the Phase I part and G 1 000 mg/m(2) day 1 and 15, O 60 mg/m(2) day 1...... and 15, and C 1 000 mg/m(2) BID day 1-7 and day 15-21 were established as MTD. In the Phase II part, 41 patients with advanced CC were included. Overall response rate was 34% and 51% had stable disease, resulting in a clinical benefit rate of 85%. Grade III and IV adverse events were rare. Median...

  3. A quality assurance audit: phase iii trial of maximal androgen deprivation in prostate cancer (TROG 96.01)

    International Nuclear Information System (INIS)

    Steigler, A.; Kovacev, O.; Denham, J.; Lamb, D.; North, J.

    2000-01-01

    In 1997 the Trans-Tasman Radiation Oncology Group (TROG) performed a quality assurance (QA) audit of its phase III randomized clinical trial investigating the effectiveness of different durations of maximal androgen deprivation prior to and during definitive radiation therapy for locally advanced carcinoma of the prostate (TROG 96.01). The audit reviewed a total of 60 cases from 15 centres across Australia and New Zealand. In addition to verification of technical adherence to the protocol, the audit also incorporated a survey of centre planning techniques and a QA time/cost analysis. The present report builds on TROG's first technical audit conducted in 1996 for the phase III accelerated head and neck trial (TROG 91.01) and highlights the significant progress TROG has made in the interim period. The audit provides a strong validation of the results of the 96.01 trial, as well as valuable budgeting and treatment planning information for future trials. Overall improvements were detected in data quality and quantity, and in protocol compliance, with a reduction in the rate of unacceptable protocol violations from 10 to 4%. Audit design, staff education and increased data management resources were identified as the main contributing factors to these improvements. In addition, a budget estimate of $100 per patient has been proposed for conducting similar technical audits. The next major QA project to be undertaken by TROG during the period 1998-1999 is an intercentre dosimetry study. Trial funding and staff education have been targeted as the key major issues essential to the continued success and expansion of TROG's QA programme. Copyright (1999) Blackwell Science Pty Ltd

  4. Phase transition of solid bismuth under high pressure

    International Nuclear Information System (INIS)

    Chen Hai-Yan; Xiang Shi-Kai; Yan Xiao-Zhen; Zhang Yi; Liu Sheng-Gang; Bi Yan; Zheng Li-Rong

    2016-01-01

    As a widely used pressure calibrator, the structural phase transitions of bismuth from phase I, to phase II, to phase III, and then to phase V with increasing pressure at 300 K have been widely confirmed. However, there are different structural versions for phase III, most of which are determined by x-ray diffraction (XRD) technology. Using x-ray absorption fine structure (XAFS) measurements combined with ab initio calculations, we show that the proposed incommensurate composite structure of bismuth of the three configurations is the best option. An abnormal continuous increase of the nearest-neighbor distance of phase III with elevated pressure is also observed. The electronic structure transformation from semimetal to metal is responsible for the complex behavior of structure transformation. (paper)

  5. Nitrato-complexes of Y(III), La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl) benzimidazole

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, A; Singh, M P; Singh, V K

    1982-05-01

    The nitrato-complexes, (Y(PyBzH)/sub 2/(NO/sub 3/)/sub 2/)NO/sub 3/.H/sub 2/O and Nd, Sm, Gd, Tb, Dy, Ho ; n=1-3, m=0-0.5 ; PyBzh=2-(2 -pyridyl)benzimidazole) are formed on interaction of the ligand with metal nitrates in ethanol. The electrical conductance values (116-129 ohm/sup -1/cm/sup 2/mol/sup -1/) suggest 1:1 electrolyte-nature of the complexes. Magnetic moment values of Ce(2.53 B.M.), Pr(3.62 B.M.), Nd(3.52 B.M.), Sm(1.70 B.M.), Gd(8.06 B.M.), Tb(9.44 B.M.), Dy(10.56 B.M.) and Ho(10.51 B.M.) in the complexes confirm the positive state of the metals. Infrared evidences are obtained for the existance of both coordinated (C/sub 2/v) and uncoordinated (D/sub 3/h) nitrate groups. Electronic absorption spectra of Pr(III)-, Nd(III)-, Sm(III)-, Tb(III)-, Dy(III)- and Ho(III)-complexes have been analysed in the light of LSJ terms.

  6. Nitrato-complexes of Y(III), La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl) benzimidazole

    International Nuclear Information System (INIS)

    Mishra, A.; Singh, M.P.; Singh, V.K.

    1982-01-01

    The nitrato-complexes, [Y(PyBzH) 2 (NO 3 ) 2 ]NO 3 .H 2 O and Nd, Sm, Gd, Tb, Dy, Ho ; n=1-3, m=0-0.5 ; PyBzh=2-(2 -pyridyl)benzimidazole] are formed on interaction of the ligand with metal nitrates in ethanol. The electrical conductance values (116-129 ohm -1 cm 2 mol -1 ) suggest 1:1 electrolyte-nature of the complexes. Magnetic moment values of Ce(2.53 B.M.), Pr(3.62 B.M.), Nd(3.52 B.M.), Sm(1.70 B.M.), Gd(8.06 B.M.), Tb(9.44 B.M.), Dy(10.56 B.M.) and Ho(10.51 B.M.) in the complexes confirm the terpositive state of the metals. Infrared evidences are obtained for the existance of both coordinated (C 2 v) and uncoordinated (D 3 h) nitrate groups. Electronic absorption spectra of Pr(III)-, Nd(III)-, Sm(III)-, Tb(III)-, Dy(III)- and Ho(III)-complexes have been analysed in the light of LSJ terms. (author)

  7. Analogues of Cucurbita maxima trypsin inhibitor III (CMTI-III) with elastase inhibitory activity.

    Science.gov (United States)

    Rózycki, J; Kupryszewski, G; Rolka, K; Ragnarsson, U; Zbyryt, T; Krokoszyńska, I; Wilusz, T

    1994-04-01

    Three new CMTI-III analogues containing the Val residue in the reactive site (position 5) were synthesized by the solid-phase method. The analogues displayed an elastase inhibitory activity. It is shown that the removal of the N-terminal Arg residue and the introduction of the Gly-Pro-Gln tripeptide in the region 23-25 decreases the antielastase activity by two orders of magnitude. The removal of the disulfide bridge in positions 16-28 and the substitution of Ala for Cys16 and Gly for Cys28 decreases the activity (measured as Ka with HLE) by five orders of magnitude as compared with [Val5]CMTI-III.

  8. CIM5 Phase III base process development results

    International Nuclear Information System (INIS)

    Witt, D.C.

    2000-01-01

    Integrated Demonstration Runs for the Am/Cm vitrification process were initiated in the Coupled 5-inch Cylindrical Induction Melter (CIM5) on 11/30/98 and completed on 12/9/98. Four successful runs at 60 wt% lanthanide loading were completed which met or exceeded all established criteria. The operating parameters used in these runs established the base conditions for the 5-inch Cylindrical Induction Melter (CIM5) process and were summarized in the 5-inch CIM design basis, SRT-AMC-99-OO01. (1) In subsequent tests, a total of fourteen CIM5 runs were performed using various power inputs, ramp rates and target temperatures to define the preferred processing conditions (2) Process stability and process flexibility were the key criteria used in assessing the results for each run. A preferred set of operating parameters was defined for the CIM5 batch process and these conditions were used to generate a pre-programmed, automatic processing cycle that was used for the last six CIM.5 runs (3) These operational tests were successfully completed in the January-February time frame and were summarized in SRT-AMC-99-00584. The recommended set of operating conditions defined in Runs No.1 through No.14 was used as the starting point for further pilot system runs to determine the robustness of the process, evaluate a bubbler, and investigate off-normal conditions. CIM5 Phase III Runs No.15 through No.60 were conducted utilizing the pre-programmed, automatic processing cycle to investigate system performance. This report summarizes the results of these tests and provides a recommendation for the base process as well as a processing modification for minimizing volume expansions if americium and/or curium are subject to a thermal reduction reaction like cerium. This document summarizes the results of the base process development tests conducted in the Am/Cm Pilot Facility located in Building 672-T

  9. Comprehensive safety assessment of a human inactivated diploid enterovirus 71 vaccine based on a phase III clinical trial.

    Science.gov (United States)

    Zhang, Wei; Kong, Yujia; Jiang, Zhiwei; Li, Chanjuan; Wang, Ling; Xia, Jielai

    2016-04-02

    Human enterovirus 71 (EV71) is a causative agent of hand, foot, and mouth disease (HFMD). In a previous phase III trial in children, a human diploid cell-based inactivated EV71 vaccine elicited EV71 specific immune responses and protection against EV71 associated HFMD. This study aimed to assess the factors influencing the severity of adverse events observed in this previous trial. This was a randomized, double-blinded, placebo-controlled, phase III clinical trial of a human diploid vaccine carried out in 12,000 children in Guangxi Zhuang Autonomous Region, China (ClinicalTrials.gov: NCT01569581). Solicited events were recorded for 7 days and unsolicited events were reported for 28 days after each injection. Age trend analysis of adverse reaction was conducted in each treatment group. Multiple logistic regression models were built to identify factors influencing the severity of adverse reactions. Fewer solicited adverse reactions were observed in older participants within the first 7 days after vaccination (P < 0.0001), except local pain and pruritus. More severe adverse reactions were observed after the initial injection than after the booster injection. Serious cold or respiratory tract infections (RTI) were observed more often in children aged 6-36 months than in older children. Only the severity of local swelling was associated with body mass index. Children with throat discomfort before injection had a higher risk of serious cold or RTI. These results indicated that the human diploid cell-based vaccine achieved a satisfactory safety profile.

  10. Adsorption behavior of Am(III) on granite

    International Nuclear Information System (INIS)

    Zhang Yingjie; Feng Xiaogui; Liang Junfu; Chen Jing; Su Rui; Wang Ju; Liu Chunli

    2009-01-01

    The adsorption behavior of Am(III) on granite (sampled from drilling well BS01 at Beishan (BS) area--a potential candidate site for China's high-level radioactive waste repository, the granite sample's depth about 300 m) was studied in BS03 well groundwater by a batch technique at (25±1) degree C. The influences of pH, sulphate ion, total carbonate ion, humic acid, and concentration of the Am(III) on the adsorption behavior were also studied, and the possible adsorption mechanism was discussed. Experimental results show that the adsorption distribution rate of Am(III) on granite increases with increasing pH of aqueous phase. The chemical composition of the groundwater is the main factor which influences the species of Am(III) and adsorption behavior. The adsorption mechanism of Am(III) on granite is surface complexation. The adsorption isotherm of Am(III) on granite can be described by Freundlich's equation. (authors)

  11. Joint Operations 2030 - Phase III Report: The JO 2030 Capability Set (Operations interarmees 2030 - Rapport Phase III: L’ensemble capacitaire JO 2030)

    Science.gov (United States)

    2011-04-01

    Registry for EU and ul. Ostrobramska 109 NATO FRANCE 04-041 Warszawa Vojkova 55 O.N.E.R.A. (ISP) 1000 Ljubljana 29, Avenue de la Division...Ostrobramska 109 Dstl Knowledge and Information Streitkräfteamt / Abteilung III 04-041 Warszawa Services Fachinformationszentrum der Bundeswehr (FIZBw

  12. Magnetic solid-phase extraction combined with graphite furnace atomic absorption spectrometry for speciation of Cr(III) and Cr(VI) in environmental waters.

    Science.gov (United States)

    Jiang, Hong-mei; Yang, Ting; Wang, Yan-hong; Lian, Hong-zhen; Hu, Xin

    2013-11-15

    A new approach of magnetic solid phase extraction (MSPE) coupled with graphite furnace atomic absorption spectrometry (GFAAS) has been developed for the speciation of Cr(III) and Cr(VI) using zincon-immobilized silica-coated magnetic Fe3O4 nanoparticles (Zincon-Si-MNPs) as the MSPE absorbent. Cr(III) was quantitatively reserved on the absorbent at pH 9.1 while total Cr was reserved at pH 6.5. The absorbed Cr species were eluted by using 2 mol/L HCl and detected by GFAAS. The concentration of Cr(VI) could be calculated by subtracting Cr(III) from total Cr. All the parameters affecting the separation and extraction efficiency of Cr species such as pH, extraction time, concentration and volume of eluent, sample volume and influence of co-existing ions were systematically examined and the optimized conditions were established accordingly. The detection limit (LOD) of the method was 0.016 and 0.011 ng mL(-1) for Cr(III) and Cr(VI), respectively, with the enrichment factor of 100 and 150. The precisions of this method (Relative standard deviation, RSD, n=7) for Cr(III) and Cr(VI) at 0.1 ng mL(-1) were 6.0% and 6.2%, respectively. In order to validate the proposed method, a certified reference material of environmental water was analyzed, and the result of Cr speciation was in good agreement with the certified value. This MSPE-GFAAS method has been successfully applied for the speciation of Cr(III) and Cr(VI) in lake and tap waters with the recoveries of 88-109% for the spiked samples. Moreover, the MSPE separation mechanism of Cr(III) and Cr(VI) based on their adsorption-desorption on Zincon-Si-MNPs has been explained through various spectroscopic characterization. © 2013 Elsevier B.V. All rights reserved.

  13. Position-controlled epitaxial III-V nanowires on silicon

    Energy Technology Data Exchange (ETDEWEB)

    Roest, Aarnoud L; Verheijen, Marcel A; Wunnicke, Olaf; Serafin, Stacey; Wondergem, Harry; Bakkers, Erik P A M [Philips Research Laboratories, Professor Holstlaan 4, 5656 AA Eindhoven (Netherlands); Kavli Institute of NanoScience, Delft University of Technology, PO Box 5046, 2600 GA Delft (Netherlands)

    2006-06-14

    We show the epitaxial integration of III-V semiconductor nanowires with silicon technology. The wires are grown by the VLS mechanism with laser ablation as well as metal-organic vapour phase epitaxy. The hetero-epitaxial growth of the III-V nanowires on silicon was confirmed with x-ray diffraction pole figures and cross-sectional transmission electron microscopy. We show preliminary results of two-terminal electrical measurements of III-V nanowires grown on silicon. E-beam lithography was used to predefine the position of the nanowires.

  14. Position-controlled epitaxial III-V nanowires on silicon

    International Nuclear Information System (INIS)

    Roest, Aarnoud L; Verheijen, Marcel A; Wunnicke, Olaf; Serafin, Stacey; Wondergem, Harry; Bakkers, Erik P A M

    2006-01-01

    We show the epitaxial integration of III-V semiconductor nanowires with silicon technology. The wires are grown by the VLS mechanism with laser ablation as well as metal-organic vapour phase epitaxy. The hetero-epitaxial growth of the III-V nanowires on silicon was confirmed with x-ray diffraction pole figures and cross-sectional transmission electron microscopy. We show preliminary results of two-terminal electrical measurements of III-V nanowires grown on silicon. E-beam lithography was used to predefine the position of the nanowires

  15. Electronic construction collaboration system : phase III.

    Science.gov (United States)

    2011-12-01

    This phase of the electronic collaboration project involved two major efforts: 1) implementation of AEC Sync (formerly known as Attolist), a web-based project management system (WPMS), on the Broadway Viaduct Bridge Project and the Iowa Falls Arch Br...

  16. Phase III trial of cetuximab with continuous or intermittent fluorouracil, leucovorin, and oxaliplatin (Nordic FLOX) versus FLOX alone in first-line treatment of metastatic colorectal cancer

    DEFF Research Database (Denmark)

    Tveit, Kjell Magne; Guren, Tormod; Glimelius, Bengt

    2012-01-01

    The NORDIC-VII multicenter phase III trial investigated the efficacy of cetuximab when added to bolus fluorouracil/folinic acid and oxaliplatin (Nordic FLOX), administered continuously or intermittently, in previously untreated metastatic colorectal cancer (mCRC). The influence of KRAS mutation...

  17. Solution and gas phase evidence of anion binding through the secondary bonding interactions of a bidentate bis-antimony(iii) anion receptor.

    Science.gov (United States)

    Qiu, J; Song, B; Li, X; Cozzolino, A F

    2017-12-20

    The solution and gas phase halide binding to a bis-antimony(iii) anion receptor was studied. This new class of anion receptors utilizes the strong Sb-centered secondary bonding interactions (SBIs) that are formed opposite to the polar Sb-O primary bond. 1 H NMR titration data were fitted statistically to binding models and solution-phase binding energetics were extracted, while the formation of anion-to-receptor complexes was observed using ESI-MS. Density functional theory calculations suggest that their affinity towards binding halide anions is mitigated by the strong explicit solvation effect in DMSO, which gives insights into future designs that circumvent direct solvent binding and are anticipated to yield tighter and perhaps more selectivity in anion binding.

  18. Effects of recombinant human granulocyte colony-stimulating factor on leucopenia in zidovudine-treated patients with AIDS and AIDS related complex, a phase I/II study

    NARCIS (Netherlands)

    van der Wouw, P. A.; van Leeuwen, R.; van Oers, R. H.; Lange, J. M.; Danner, S. A.

    1991-01-01

    Twelve male patients, eight with the acquired immunodeficiency syndrome (AIDS) and four with AIDS related complex (ARC), who had zidovudine associated neutropenia (less than 1 x 10(9) neutrophils/l) were treated with recombinant human granulocyte colony-stimulating factor (G-CSF) in a phase I/II

  19. Recruiting long-term survivors of European Organisation for Research and Treatment of Cancer phase III clinical trials into quality of life studies : Challenges and opportunities

    NARCIS (Netherlands)

    van Leeuwen, M.L.; Efficace, F.; Fosså, S.D.; Bolla, M.; de Giorgi, U.; De Wit, R.; Holzner, B.; van de Poll-Franse, L.; White, J.; Collette, L.; Osanto, S.; Aaronson, N.K.; European Organisation for Research and Treatment of Cancer Quality of Life Group; Genito-Urinary Cancers Group, The

    2014-01-01

    Objectives In this pilot study we evaluated the feasibility of and methods for assessing the quality of life of long term survivors of European Organisation for Research and Treatment of Cancer (EORTC) phase III clinical trials. Here we report the results pertaining to the feasibility of conducting

  20. Recruiting long-term survivors of European Organisation for Research and Treatment of Cancer phase III clinical trials into quality of life studies: Challenges and opportunities

    NARCIS (Netherlands)

    van Leeuwen, M.; Efficace, F.; Fosså, S.D.; Bolla, M.; De Giorgi, U.; de Wit, R; Holzner, B.; van de Poll-Franse, L.V.; van Poppel, H.; White, J.; Collette, L.; Osanto, S.; Aaronson, N.K.

    2014-01-01

    Objectives: In this pilot study we evaluated the feasibility of and methods for assessing the quality of life of long term survivors of European Organisation for Research and Treatment of Cancer (EORTC) phase III clinical trials. Here we report the results pertaining to the feasibility of conducting

  1. Material handling systems for use in glovebox lines: A survey of Department of Energy facility experience

    International Nuclear Information System (INIS)

    Teese, G.D.; Randall, W.J.

    1992-01-01

    The Nuclear Weapons Complex Reconfiguration Study has recommended that a new manufacturing facility be constructed to replace the Rocky Flats Plant. In the new facility, use of an automated material handling system for movement of components would reduce both the cost and radiation exposure associated with production and maintenance operations. Contamination control would be improved between process steps through the use of airlocks and portals. Part damage associated with improper transport would be reduced, and accountability would be increased. In-process workpieces could be stored in a secure vault, awaiting a request for parts at a production station. However, all of these desirable features rely on the proper implementation of an automated material handling system. The Department of Energy Weapons Production Complex has experience with a variety of methods for transporting discrete parts in glovebox lines. The authors visited several sites to evaluate the existing technologies for their suitability for the application of plutonium manufacturing. Technologies reviewed were Linear motors, belt conveyors, roller conveyors, accumulating roller conveyors, pneumatic transport, and cart systems. The sites visited were The Idaho National Engineering laboratory, the Hanford Site, and the Rocky Flats Plant. Linear motors appear to be the most promising technology observed for the movement of discrete parts, and further investigation is recommended

  2. Implementation of dynamic cross-talk correction (DCTC) for MOX holdup assay measurements among multiple gloveboxes

    International Nuclear Information System (INIS)

    Nakamichi, Hideo; Nakamura, Hironobu; Mukai, Yasunobu; Kurita, Tsutomu; Beddingfield, David H.

    2012-01-01

    Plutonium holdup in gloveboxes (GBs) are measured by (passive neutron based NDA (HBAS) for the material control and accountancy (MC and A) at Plutonium Conversion Development Facility (PCDF). In the case that the GBs are installed close to one another, the cross-talk which means neutron double counting among GBs should be corrected properly. Though we used to use predetermined constants as the cross-talk correction, a new correction methodology for neutron cross-talk among the GBs with inventory changes is required for the improvement of MC and A. In order to address the issue of variable cross-talk contributions to holdup assay values, we applied a dynamic cross-talk correction (DCTC) method, based on the distributed source-term analysis approach, to obtain the actual doubles derived from the cross-talk between multiple GBs. As a result of introduction of DCTC for HBAS measurement, we could reduce source biases from the assay result by estimating the reliable doubles-counting derived from the cross-talk. Therefore, we could improve HBAS measurement uncertainty to a half of conventional system, and we are going to confirm the result. Since the DCTC methodology can be used to determine the cross-correlation among multiple inventories in small areas, it is expected that this methodology can be extended to the knowledge of safeguards by design. (author)

  3. Doublet III: status and future plans

    International Nuclear Information System (INIS)

    Rawls, J.M.

    1980-04-01

    A synopsis is presented of the experimental results from the ohmic heating phase of Doublet III, with emphasis on the production of good target plasmas for the upcoming neutral beam injection phase. The program plan for the device over the life of the US-Japan cooperative program is discussed, as is the status of the preliminary investigation into replacing the present vacuum vessel by one better suited for ETF simulation

  4. The PACOVAR-trial: A phase I/II study of pazopanib (GW786034) and cyclophosphamide in patients with platinum-resistant recurrent, pre-treated ovarian cancer

    International Nuclear Information System (INIS)

    Eichbaum, Michael; Fersis, Nikos; Schmidt, Marcus; Wallwiener, Markus; Schneeweiss, Andreas; Sohn, Christof; Mayer, Christine; Eickhoff, Regina; Bischofs, Esther; Gebauer, Gerhard; Fehm, Tanja; Lenz, Florian; Fricke, Hans-Christian; Solomayer, Erich

    2011-01-01

    The prognosis of patients with recurrent, platinum-resistant epithelial ovarian cancer (EOC) is poor. There is no standard treatment available. Emerging evidence suggests a major role for antiangiogenic treatment modalities in EOC, in particular in combination with the metronomic application of low dose chemotherapy. The novel, investigational oral antiangiogenic agent pazopanib targeting vascular endothelial growth factor receptor (VEGFR), platelet-derived growth factor receptor (PDGFR) and c-kit is currently being studied in different tumour types and is already used as first line therapy in recurrent renal cell carcinoma. A combined therapy consisting of pazopanib and metronomic oral cyclophosphamide may offer a well-tolerable treatment option to patients with recurrent, pretreated EOC. This study is designed as a multicenter phase I/II trial evaluating the optimal dose for pazopanib (phase I) as well as activity and tolerability of a combination regimen consisting of pazopanib and metronomic cyclophosphamide in the palliative treatment of patients with recurrent, platinum-resistant, pre-treated ovarian cancer (phase II). The patient population includes patients with histologically or cytologically confirmed diagnosis of EOC, cancer of the fallopian tube or peritoneal cancer which is platinumresistant or -refractory. Patients must have measurable disease according to RECIST criteria and must have failed available standard chemotherapy. Primary objectives are determination of the optimal doses for pazopanib (phase I) and the overall response rate according to RECIST criteria (phase II). Secondary objectives are time to progression, overall survival, safety and tolerability. The treatment duration is until disease progression or intolerability of study drug regimen (with a maximum of 13 cycles up to 52 weeks per subject). The current phase I/II trial shall clarify the potential of the multitargeting antiangiogenic tyrosinkinaseinhibitor GW 786034 (pazopanib) in

  5. Solid phase extraction of Am (III) by resins impregnated with multiply diglycolamide-functionalized ligands

    International Nuclear Information System (INIS)

    Gujar, R.B.; Ansari, S.A.; Mohapatra, P.K.; Verboom, W.

    2016-01-01

    Solvent extraction studies with multiply diglycolamide-functionalized extractants such as tripodal diglycolamide (T-DGA) or diglycolamide-functionalized calix(4)arene (C4DGA) ligands have shown excellent results as compared to those of normal DGA ligands such as TODGA. A very high selectivity for Am(III) has been reported with these ligands with respect to U(VI) and Pu(IV). High selectivities and large extraction efficiencies of these ligands towards trivalent f elements were ascribed to a co-operative complexation mechanism. Furthermore, the extraction efficiency of these ligands increased several folds in ionic liquid medium as compared to paraffinic solvents. It was of interest, therefore, to prepare extraction chromatographic resins by impregnation of solvent systems containing these ligands in an ionic liquid. In the present work, solid phase extraction studies were carried out using these two multiply diglycolamide-functionalized extractants, viz. T-DGA (resin I) and C4DGA (resin-II) containing the ionic liquid C 4 mim. NTf 2 impregnated on Chromosorb-W

  6. Phase III Randomized Clinical Trial Comparing Tremelimumab With Standard-of-Care Chemotherapy in Patients With Advanced Melanoma

    Science.gov (United States)

    Ribas, Antoni; Kefford, Richard; Marshall, Margaret A.; Punt, Cornelis J.A.; Haanen, John B.; Marmol, Maribel; Garbe, Claus; Gogas, Helen; Schachter, Jacob; Linette, Gerald; Lorigan, Paul; Kendra, Kari L.; Maio, Michele; Trefzer, Uwe; Smylie, Michael; McArthur, Grant A.; Dreno, Brigitte; Nathan, Paul D.; Mackiewicz, Jacek; Kirkwood, John M.; Gomez-Navarro, Jesus; Huang, Bo; Pavlov, Dmitri; Hauschild, Axel

    2013-01-01

    Purpose In phase I/II trials, the cytotoxic T lymphocyte–associated antigen-4–blocking monoclonal antibody tremelimumab induced durable responses in a subset of patients with advanced melanoma. This phase III study evaluated overall survival (OS) and other safety and efficacy end points in patients with advanced melanoma treated with tremelimumab or standard-of-care chemotherapy. Patients and Methods Patients with treatment-naive, unresectable stage IIIc or IV melanoma were randomly assigned at a ratio of one to one to tremelimumab (15 mg/kg once every 90 days) or physician's choice of standard-of-care chemotherapy (temozolomide or dacarbazine). Results In all, 655 patients were enrolled and randomly assigned. The test statistic crossed the prespecified futility boundary at second interim analysis after 340 deaths, but survival follow-up continued. At final analysis with 534 events, median OS by intent to treat was 12.6 months (95% CI, 10.8 to 14.3) for tremelimumab and 10.7 months (95% CI, 9.36 to 11.96) for chemotherapy (hazard ratio, 0.88; P = .127). Objective response rates were similar in the two arms: 10.7% in the tremelimumab arm and 9.8% in the chemotherapy arm. However, response duration (measured from date of random assignment) was significantly longer after tremelimumab (35.8 v 13.7 months; P = .0011). Diarrhea, pruritus, and rash were the most common treatment-related adverse events in the tremelimumab arm; 7.4% had endocrine toxicities. Seven deaths in the tremelimumab arm and one in the chemotherapy arm were considered treatment related by either investigators or sponsor. Conclusion This study failed to demonstrate a statistically significant survival advantage of treatment with tremelimumab over standard-of-care chemotherapy in first-line treatment of patients with metastatic melanoma. PMID:23295794

  7. Phase III randomized clinical trial comparing tremelimumab with standard-of-care chemotherapy in patients with advanced melanoma.

    Science.gov (United States)

    Ribas, Antoni; Kefford, Richard; Marshall, Margaret A; Punt, Cornelis J A; Haanen, John B; Marmol, Maribel; Garbe, Claus; Gogas, Helen; Schachter, Jacob; Linette, Gerald; Lorigan, Paul; Kendra, Kari L; Maio, Michele; Trefzer, Uwe; Smylie, Michael; McArthur, Grant A; Dreno, Brigitte; Nathan, Paul D; Mackiewicz, Jacek; Kirkwood, John M; Gomez-Navarro, Jesus; Huang, Bo; Pavlov, Dmitri; Hauschild, Axel

    2013-02-10

    In phase I/II trials, the cytotoxic T lymphocyte-associated antigen-4-blocking monoclonal antibody tremelimumab induced durable responses in a subset of patients with advanced melanoma. This phase III study evaluated overall survival (OS) and other safety and efficacy end points in patients with advanced melanoma treated with tremelimumab or standard-of-care chemotherapy. Patients with treatment-naive, unresectable stage IIIc or IV melanoma were randomly assigned at a ratio of one to one to tremelimumab (15 mg/kg once every 90 days) or physician's choice of standard-of-care chemotherapy (temozolomide or dacarbazine). In all, 655 patients were enrolled and randomly assigned. The test statistic crossed the prespecified futility boundary at second interim analysis after 340 deaths, but survival follow-up continued. At final analysis with 534 events, median OS by intent to treat was 12.6 months (95% CI, 10.8 to 14.3) for tremelimumab and 10.7 months (95% CI, 9.36 to 11.96) for chemotherapy (hazard ratio, 0.88; P = .127). Objective response rates were similar in the two arms: 10.7% in the tremelimumab arm and 9.8% in the chemotherapy arm. However, response duration (measured from date of random assignment) was significantly longer after tremelimumab (35.8 v 13.7 months; P = .0011). Diarrhea, pruritus, and rash were the most common treatment-related adverse events in the tremelimumab arm; 7.4% had endocrine toxicities. Seven deaths in the tremelimumab arm and one in the chemotherapy arm were considered treatment related by either investigators or sponsor. This study failed to demonstrate a statistically significant survival advantage of treatment with tremelimumab over standard-of-care chemotherapy in first-line treatment of patients with metastatic melanoma.

  8. Clinical efficacy of raltegravir against B and non-B subtype HIV-1 in phase III clinical studies.

    Science.gov (United States)

    Rockstroh, Jürgen K; Teppler, Hedy; Zhao, Jing; Sklar, Peter; Miller, Michael D; Harvey, Charlotte M; Strohmaier, Kim M; Leavitt, Randi Y; Nguyen, Bach-Yen T

    2011-07-17

    We evaluated the long-term efficacy of raltegravir according to HIV-1 subtype (B and non-B) using data from three phase III studies in treatment-experienced (BENCHMRK-1 and 2) and treatment-naive (STARTMRK) HIV-infected patients. HIV-1 subtypes were identified from baseline plasma specimens using genotypic data of the PhenoSense GT test (Monogram Biosciences, South San Francisco, California, USA). Non-B subtypes were combined for the current analyses due to small numbers of each specific subtype. An observed failure approach was used (only discontinuations due to lack of efficacy were treated as failures). Resistance evaluation was performed in patients with documented virologic failure. Seven hundred and forty-three patients received raltegravir and 519 received comparator (efavirenz in STARTMRK; optimized background therapy in BENCHMRK). Non-B subtype virus (A, A/C, A/D, A/G, A1, AE, AG, B/G, BF, C, D, D/F, F, F1, G, and complex) was isolated at baseline in 98 (13%) raltegravir recipients and 62 (12%) comparator recipients. Subtypes AE and C were most common, isolated in 41 and 43 patients, respectively. The proportion of raltegravir recipients achieving HIV RNA less than 50 copies/ml was similar between non-B and B subtypes (STARTMRK: 94.5 vs. 88.7%; BENCHMRK-1 and 2: 66.7 vs. 60.7%); change in CD4 cell count also was similar between non-B and B subtypes (STARTMRK: 243 vs. 221 cells/μl; BENCHMRK-1 and 2: 121 vs. 144 cells/μl). Phenotypic resistance to raltegravir in non-B virus was associated with integrase mutations observed previously in subtype B virus. In phase III studies in treatment-naive and treatment-experienced patients, raltegravir showed comparable and potent clinical efficacy against B and non-B HIV-1 subtypes.

  9. Extraction of Am (III) and Nd (III): comparison of TODGA and TEHDGA

    International Nuclear Information System (INIS)

    Gujar, R.B.; Murali, M.S.; Ansari, S.A.; Manchanda, V.K.

    2009-01-01

    Belonging to the class of extractants, diglycolamides which are recently explored and promising for actinide partitioning, two reagents (N, N, N', N'-tetraoctyl diglycolamide) TODGA and its isomerically substituted counterpart, (N, N, N', N'- tetraethylhexyl diglycolamide) TEHDGA after addition of suitable phase modifiers, Dihexyoctanamide and isodecanol respectively in dodecane have been compared in their extraction abilities for Am (III) and Nd (III) from nitric acid as well as simulated high-level waste solutions (SHLW) equivalent to HLW arising from PHWR fuel reprocessing. Both 0.1M TODGA + 0.5M DHOA and 0.2M TEHDGA + 30% isodecanol in dodecane display high distribution ratios for the trivalent metal ions of f-elements. Similarities and differences in their extraction are discussed. (author)

  10. Probing Fe (III)/Fe (II) redox potential in a clayey material

    International Nuclear Information System (INIS)

    Tournassat, Christophe; Chainet, Fabien; Betelu, Stephanie; Hadi, Jebril; Gaucher, Eric C.; Ignatiadis, Ioannis; Greneche, Jean-Marc; Charlet, Laurent

    2010-01-01

    Document available in extended abstract form only. Redox is one of the main factors affecting the migration of redox-sensitive radionuclides. As a consequence reducing conditions are considered of strategic importance for the confinement properties of a clayey formation towards nuclear waste. A representative redox potential of clay formation such as Callovian- Oxfordian (COx) can be derived from thermodynamic calculations considering equilibrium between observed redox phases such as pyrite and siderite. However, there is little information on the reactivity of the different reservoirs of redox constituents in this type of complex material. The present study aims at investigating the reactivity of the Fe(III)/Fe(II) redox couple in the structure of clay minerals using different investigation methods: electrochemistry and O 2 reduction kinetic experiments. Clay modified electrodes were specifically designed to probe Fe(III)/Fe(II) redox potential in the structure of clay minerals. The clay fraction of a Callovian-Oxfordian argillite sample originating from the same level than ANDRA underground research laboratory was used after pre-treatment to remove organic matter and accessory minerals such as pyrite that could influence redox potential measurements. These electrodes were used to verify the validity of the model of Favre et al. (2006) that links the redox potential (E clay ) to the the Fe(II)/Fe tot ratio in the structure (m rel ), the pH and the sodium concentration in solution: equation 1. The good agreement between direct potential measurements and model prediction provides a strong evidence of the relevance of this model in our experimental conditions although the clay composition and its too low Fe content do not a priori fulfil the conditions set by Drits and Manceau (2000) for the calculation of K 0 parameter. Following the verification of the model, we tried to apply it to the specific case of a Callovian-Oxfordian sample that had been very well preserved

  11. Monte Carlo studies of ZEPLIN III

    CERN Document Server

    Dawson, J; Davidge, D C R; Gillespie, J R; Howard, A S; Jones, W G; Joshi, M; Lebedenko, V N; Sumner, T J; Quenby, J J

    2002-01-01

    A Monte Carlo simulation of a two-phase xenon dark matter detector, ZEPLIN III, has been achieved. Results from the analysis of a simulated data set are presented, showing primary and secondary signal distributions from low energy gamma ray events.

  12. Separation of yttrium (III) from lanthanoids (III) by solvent extraction with substituted N-Alkylcarbonyl-N-phenylhydroxylamines

    International Nuclear Information System (INIS)

    Haraguchi, K.; Ogata, T.; Nakagawa, K.; Saitoh, T.; Kamidate, T.; Watanabe, H.

    1996-01-01

    A series of substituted N-alkylcarbonyl-N-phenylhydroxylamines(R-PHAs) were synthesized and utilized for the extraction of yttrium(III) and lanthanoids(III) in order to obtain effective extractants for the separation of yttrium(III) from the lanthanoids(III) and the mutual separation of the lanthanoids(III). The distribution ratio of yttrium(III) and the lanthanoids(III) between the carbon tetrachloride and the aqueous phases was measured as functions of the pH and the extractant concentration at 298 K at an ionic strength of 0.1 (NaNO 3 ). Yttrium(III) and the lanthanoids(III) were extracted with R-PHAs(HL) as self-adducted chelates of the form, ML 3 (HL) x , where 'x' is 1, 2 or 3 depending on the extraction system. The extractability of the metal ions decreased in the order of R-PHA having a primary, a secondary and a tertiary alkyl substituent attached to the carbonyl group because of the steric hindrance of the alkyl group. The separation factors for both Yb/Eu and Yb/Y pairs increased with increasing branching of the alkyl group of R-PHA. The excellent selectivity of R-PHAs having a tertiary alkyl group was attributable to a greater inductive effect of the tertiary alkyl group than those of the primary and secondary alkyl groups. The substituents at the phenyl group of R-PHAs gave no significant effect on the selectivity, while the extractability was enhanced considerably by introduction of electron withdrawing substituents at appropriate positions of the phenyl group of R-PHAs. (authors)

  13. Phase II/III multicentre randomised controlled trial evaluating a strategy of primary surgery and adjuvant chemotherapy versus peri-operative chemotherapy for resectable gastric signet ring cell adenocarcinomas – PRODIGE 19 – FFCD1103 – ADCI002

    International Nuclear Information System (INIS)

    Piessen, Guillaume; Mariette, Christophe; Messager, Mathieu; Le Malicot, Karine; Robb, William B; Di Fiore, Frédéric; Guilbert, Marie; Moreau, Marie; Christophe, Véronique; Adenis, Antoine

    2013-01-01

    A dramatic increase in the incidence of the diffuse form of gastric adenocarcinomas and particularly signet ring cell carcinomas has been observed in Western countries. Evidence is accruing that signet ring cell carcinomas may have inherent chemo resistance leaving many clinicians unsure of the benefits of delaying surgery to pursue a neoadjuvant approach. PRODIGE-19-FFCD1103-ADCI002 is a prospective multicentre controlled randomised phase II/III trial comparing current standard of care of perioperative chemotherapy (2x3 cycles of Epirubicin, cisplatin, 5-fluorouracil) with a strategy of primary surgery followed by adjuvant chemotherapy (6 cycles of Epirubicin, cisplatin, 5-fluorouracil) in patients with a stage IB-III gastric signet ring cell tumour. The principal objective of the phase II study (84 patients) is to determine if the experimental arm (primary surgery followed by adjuvant chemotherapy) has sufficient interest in terms of percentage of living patients at 24 months to be evaluated in a phase III trial. If 7 or less patients in the experimental arm are alive at 24 months, phase III will not be initiated. The primary objective of phase III (230 additional patients) is to demonstrate superiority of the experimental arm in terms of overall survival. Secondary endpoints include overall survival at 36 months, disease free survival at 24 and 36 months, R0 resection rates, treatment tolerance, postoperative mortality and morbidity evaluated by Clavien-Dindo severity index, the prognostic impact of positive peritoneal cytology and the assessment of quality of life. An ancillary study will assess the emotional and cognitive impact of surgery and perioperative chemotherapy for both the patient and their partner. As inherent chemo resistance of signet ring cell tumours and delay in definitive surgery may favour tumour progression we hypothesise that a policy of primary surgery followed by adjuvant chemotherapy will improve overall survival compared to a standard

  14. Phase II study of imatinib mesylate and hydroxyurea for recurrent grade III malignant gliomas.

    Science.gov (United States)

    Desjardins, Annick; Quinn, Jennifer A; Vredenburgh, James J; Sathornsumetee, Sith; Friedman, Allan H; Herndon, James E; McLendon, Roger E; Provenzale, James M; Rich, Jeremy N; Sampson, John H; Gururangan, Sridharan; Dowell, Jeannette M; Salvado, August; Friedman, Henry S; Reardon, David A

    2007-05-01

    Recent reports demonstrate the activity of imatinib mesylate, an ATP-mimetic, tyrosine kinase inhibitor, plus hydroxyurea, a ribonucleotide reductase inhibitor, in patients with recurrent glioblastoma multiforme. We performed the current phase 2 study to evaluate this regimen among patients with recurrent WHO grade III malignant glioma (MG). Patients with grade III MG at any recurrence, received imatinib mesylate plus hydroxyurea (500 mg twice a day) orally on a continuous, daily schedule. The imatinib mesylate dose was 500 mg twice a day for patients on enzyme inducing anti-epileptic drugs (EIAEDs) and 400 mg once a day for those not on EIAEDs. Clinical assessments were performed monthly and radiographic assessments were obtained at least every 2 months. The primary endpoint was 6-month progression-free survival (PFS) rate. Thirty-nine patients were enrolled. All patients had progressive disease after prior radiotherapy and at least temozolomide-based chemotherapy. The median number of episodes of prior progression was 2 (range, 1-7) and the median number of prior treatment regimens was 3 (range, 1-8). With a median follow-up of 82.9 weeks, 24% of patients were progression-free at 6 months. The radiographic response rate was 10%, while 33% achieved stable disease. Among patients who achieved at least stable disease at first evaluation, the 6-month and 12-month PFS rates were 53% and 29%, respectively. The most common grade 3 or greater toxicities were hematologic and complicated less than 4% of administered courses. Imatinib mesylate plus hydroxyurea, is well tolerated and associated with anti-tumor activity in some patients with recurrent grade 3 MG.

  15. Thermal behaviour of cesiumchloroferrates(III). 4

    International Nuclear Information System (INIS)

    Ziemer, B.; Fest, M.; Hass, D.; Leibnitz, P.

    1989-01-01

    Tricesium aquapentachloroferrate(III) chloride crystallizes from acid aqueous solutions of FeCl 3 · 6 H 2 O and CsCl in the triclinic space group P-bar1 with a = 714.1 pm, b = 1070.9 pm, c = 950.4 pm, α = 105.65 0 , β = 109.51 0 , γ = 89.08 0 and Z = 2. The compound is formed also from dicesium aquapentachloroferrate(III) and cesium chloride in a solid state reaction. The orientational relationships between the educt and product phases are elucidated, and a topotactic reaction mechanism is discussed. (author)

  16. Comprehensive analysis of published phase I/II clinical trials between 1990-2010 in osteosarcoma and Ewing sarcoma confirms limited outcomes and need for translational investment

    Directory of Open Access Journals (Sweden)

    van Maldegem Annemiek M

    2012-01-01

    Full Text Available Abstract Background High grade primary bone sarcomas are rare cancers that affect mostly children and young adults. Osteosarcoma and Ewing sarcoma are the most common histological subtypes in this age group, with current multimodality treatment strategies achieving 55-70% overall survival. As there remains an urgent need to develop new therapeutic interventions, we have reviewed published phase I/II trials that have been reported for osteosarcoma and Ewing sarcoma in the last twenty years. Results We conducted a literature search for clinical trials between 1990 and 2010, either for trials enrolling bone sarcoma patients as part of a general sarcoma indication or trials specifically in osteosarcoma and Ewing sarcoma. We identified 42 clinical trials that fulfilled our search criteria for general sarcoma that enrolled these patient groups, and eight and twenty specific trials for Ewing and osteosarcoma patients, respectively. For the phase I trials which enrolled different tumour types our results were incomplete, because the sarcoma patients were not mentioned in the PubMed abstract. A total of 3,736 sarcoma patients were included in these trials over this period, 1,114 for osteosarcoma and 1,263 for Ewing sarcoma. As a proportion of the worldwide disease burden over this period, these numbers reflect a very small percentage of the potential patient recruitment, approximately 0.6% for Ewing sarcoma and 0.2% for osteosarcoma. However, these data show an increase in recent activity overall and suggest there is still much room for improvement in the current trial development structures. Conclusion Lack of resources and commercial investment will inevitably limit opportunity to develop sufficiently rapid improvements in clinical outcomes. International collaboration exists in many well founded co-operative groups for phase III trials, but progress may be more effective if there were also more investment of molecular and translational research into

  17. Alterations in the rate of limb movement using a lower body positive pressure treadmill do not influence respiratory rate or phase III ventilation.

    Science.gov (United States)

    Buono, Michael J; Burnsed-Torres, Marissa; Hess, Bethany; Lopez, Kristine; Ortiz, Catherine; Girodo, Ariel; Lolli, Karen; Bloom, Brett; Bailey, David; Kolkhorst, Fred W

    2015-01-01

    The purpose of this study was to determine the effect of alterations in rate of limb movement on Phase III ventilation during exercise, independent of metabolic rate, gait style, and treadmill incline. Subjects completed five submaximal exercise bouts on a lower body positive pressure treadmill (AlterG P 200). The percent body weight for the five exercise bouts was 100, 87, 75, 63, and 50% and each was matched for carbon dioxide production (V CO2 ). Naturally, to match the V CO2 while reducing the body weight up to 50% of normal required a significant increase in the treadmill speed from 3.0 ± 0.1 to 4.1 ± 0.2 mph, which resulted in a significant (P body weight) to 133 ± 6 at 4.1 mph (i.e., 50% of body weight). The most important finding was that significant increases in step frequency did not significantly alter minute ventilation or respiratory rate. Such results do not support an important role for the rate of limb movement in Phase III ventilation during submaximal exercise, when metabolic rate, gait style, and treadmill incline are controlled.

  18. Room temperature ionic liquids enhanced the speciation of Cr(VI) and Cr(III) by hollow fiber liquid phase microextraction combined with flame atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, Chujie, E-mail: cjzeng@126.com [Department of Chemistry and Material, Yulin Normal College, Yulin, Guangxi 537000 (China); Lin, Yao; Zhou, Neng; Zheng, Jiaoting; Zhang, Wei [Department of Chemistry and Material, Yulin Normal College, Yulin, Guangxi 537000 (China)

    2012-10-30

    Highlights: Black-Right-Pointing-Pointer First reported enhancement effect of RTILs in HF-LPME for the speciation of chromium. Black-Right-Pointing-Pointer The addition of RTILs led to 3.5 times improvement of the sensitivity of Cr(VI). Black-Right-Pointing-Pointer The proposed method is a simplicity, sensitivity, low cost, green method. - Abstract: A new method for the speciation of Cr(VI) and Cr(III) based on enhancement effect of room temperature ionic liquids (RTILs) for hollow fiber liquid phase microextraction (HF-LPME) combined with flame atomic absorption spectrometry (FAAS) was developed. Room temperature ionic liquids (RTILs) and diethyldithiocarbamate (DDTC) were used enhancement reagents and chelating reagent, respectively. The addition of room temperature ionic liquids led to 3.5 times improvement in the determination of Cr(VI). In this method, Cr(VI) reacts with DDTC yielding a hydrophobic complex, which is subsequently extracted into the lumen of hollow fiber, whereas Cr(III) is remained in aqueous solutions. The extraction organic phase was injected into FAAS for the determination of Cr(VI). Total Cr concentration was determined after oxidizing Cr(III) to Cr(VI) in the presence of KMnO{sub 4} and using the extraction procedure mentioned above. Cr(III) was calculated by subtracting of Cr(VI) from the total Cr. Under optimized conditions, a detection limit of 0.7 ng mL{sup -1} and an enrichment factor of 175 were achieved. The relative standard deviation (RSD) was 4.9% for Cr(VI) (40 ng mL{sup -1}, n = 5). The proposed method was successfully applied to the speciation of chromium in natural water samples with satisfactory results.

  19. Room temperature ionic liquids enhanced the speciation of Cr(VI) and Cr(III) by hollow fiber liquid phase microextraction combined with flame atomic absorption spectrometry

    International Nuclear Information System (INIS)

    Zeng, Chujie; Lin, Yao; Zhou, Neng; Zheng, Jiaoting; Zhang, Wei

    2012-01-01

    Highlights: ► First reported enhancement effect of RTILs in HF-LPME for the speciation of chromium. ► The addition of RTILs led to 3.5 times improvement of the sensitivity of Cr(VI). ► The proposed method is a simplicity, sensitivity, low cost, green method. - Abstract: A new method for the speciation of Cr(VI) and Cr(III) based on enhancement effect of room temperature ionic liquids (RTILs) for hollow fiber liquid phase microextraction (HF-LPME) combined with flame atomic absorption spectrometry (FAAS) was developed. Room temperature ionic liquids (RTILs) and diethyldithiocarbamate (DDTC) were used enhancement reagents and chelating reagent, respectively. The addition of room temperature ionic liquids led to 3.5 times improvement in the determination of Cr(VI). In this method, Cr(VI) reacts with DDTC yielding a hydrophobic complex, which is subsequently extracted into the lumen of hollow fiber, whereas Cr(III) is remained in aqueous solutions. The extraction organic phase was injected into FAAS for the determination of Cr(VI). Total Cr concentration was determined after oxidizing Cr(III) to Cr(VI) in the presence of KMnO 4 and using the extraction procedure mentioned above. Cr(III) was calculated by subtracting of Cr(VI) from the total Cr. Under optimized conditions, a detection limit of 0.7 ng mL −1 and an enrichment factor of 175 were achieved. The relative standard deviation (RSD) was 4.9% for Cr(VI) (40 ng mL −1 , n = 5). The proposed method was successfully applied to the speciation of chromium in natural water samples with satisfactory results.

  20. A prospective phase II trial of EGCG in treatment of acute radiation-induced esophagitis for stage III lung cancer

    International Nuclear Information System (INIS)

    Zhao, Hanxi; Xie, Peng; Li, Xiaolin; Zhu, Wanqi; Sun, Xindong; Sun, Xiaorong; Chen, Xiaoting; Xing, Ligang; Yu, Jinming

    2015-01-01

    Background: Acute radiation-induced esophagitis (ARIE) is one of main toxicities complicated by thoracic radiotherapy, influencing patients’ quality of life and radiotherapy proceeding seriously. It is difficult to be cured rapidly so far. Our phase I trial preliminarily showed that EGCG may be a promising strategy in the treatment of ARIE. Materials and methods: We prospectively enrolled patients with stage III lung cancer from the Shandong Tumor Hospital & Institute in China from January 2013 to September 2014. All patients received concurrent or sequential chemo-radiotherapy, or radiotherapy only. EGCG was administrated once ARIE appeared. EGCG was given with the concentration of 440 μmol/L during radiotherapy and additionally two weeks after radiotherapy. RTOG score, dysphagia and pain related to esophagitis were recorded every week. Results: Thirty-seven patients with stage IIIA and IIIB lung cancer were enrolled in this trial. In comparison to the original, the RTOG score in the 1st, 2nd, 3rd, 4th, 5th week after EGCG prescription and the 1st, 2nd week after radiotherapy decreased significantly (P = 0.002, 0.000, 0.000, 0.001, 0.102, 0.000, 0.000, respectively). The pain score of each week was significantly lower than the baseline (P = 0.000, 0.000, 0.000, 0.000, 0.006, 0.000, 0.000, respectively). Conclusion: This trial confirmed that the oral administration of EGCG is an effective and safe method to deal with ARIE. A phase III randomized controlled trial is expected to further corroborate the consequence of EGCG in ARIE treatment

  1. Diglycolic acid modified zirconium phosphate and studies on the extraction of Am(III) and Eu(III) from dilute nitric acid medium

    Energy Technology Data Exchange (ETDEWEB)

    Selvan, B. Robert; Suneesh, A.S.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Division; Dasthaiah, K.; Gardas, R.L. [Indian Institute of Technology - Madras, Chennai (India). Dept. of Chemistry

    2017-06-01

    Diglycolic acid modified zirconium phosphate (ZrP-DGA) was prepared and studied for the extraction of Am(III) and Eu(III) from dilute nitric acid medium. The distribution coefficient (K{sub d}, mL.g{sup -1}) of Am(III) and Eu(III) was measured as a function of time, pH and concentration of Eu(III) ion etc. The K{sub d} of Am(III) and Eu(III) increased with increase of pH, reached a maximum value of distribution coefficient at pH 1.5 - 2, followed by decrease in K{sub d} values. Rapid extraction of Am(III) and Eu(III) in ZrP-DGA was observed followed by the establishment of equilibrium occurred in 100 min. Kinetics of extraction was fitted in to pseudo second order rate equation. The amount of Eu(III) loaded in ZrP-DGA increased with increase in the concentration of Eu(III) ion in aqueous phase and the isotherm was fitted in to Langmuir and Freundlich adsorption models. The extraction of Am(III) in ZrP-DGA was higher as compared to Eu(III) and the interference of Eu(III) on the extraction of Am(III) was studied. The distribution coefficient of some lanthanides in ZrP-DGA was measured and the K{sub d} of lanthanides increased across the lanthanide series. The extracted trivalent metal ions were recovered in three contacts of loaded ZrP-DGA with 0.5 M nitric acid.

  2. Phase III Randomized Study of SB5, an Adalimumab Biosimilar, Versus Reference Adalimumab in Patients With Moderate‐to‐Severe Rheumatoid Arthritis

    OpenAIRE

    Weinblatt, Michael E.; Baranauskaite, Asta; Niebrzydowski, Jaroslaw; Dokoupilova, Eva; Zielinska, Agnieszka; Jaworski, Janusz; Racewicz, Artur; Pileckyte, Margarita; Jedrychowicz‐Rosiak, Krystyna; Cheong, Soo Yeon; Ghil, Jeehoon; Sokolovic, S.; Mekic, M.; Prodanovic, N.; Gajic, B.

    2017-01-01

    Objective SB5 is a biosimilar agent for adalimumab (ADA). The aim of this study was to evaluate the efficacy, pharmacokinetics (PK), safety, and immunogenicity of SB5 in comparison with reference ADA in patients with rheumatoid arthritis (RA). Methods In this phase III, randomized, double‐blind, parallel‐group study, patients with moderately to severely active RA despite treatment with methotrexate were randomized 1:1 to receive SB5 or reference ADA at a dosage of 40 mg subcutaneously every o...

  3. Phase I/II trial of concurrent use of S-1 and radiation therapy for T2 glottic cancer

    International Nuclear Information System (INIS)

    Nakayama, Meijin; Hayakawa, Kazushige; Okamoto, Makito; Niibe, Yuzuru; Ishiyama, Hiromichi; Kotani, Shouko

    2010-01-01

    A Phase I/II study of S-1 combined radiation therapy was conducted in patients with Stage II (T2N0) glottic cancer. The purpose of the Phase I study was to identify the maximum tolerated dose, the recommended dose and the dose limiting toxicity. The objectives in the phase II study were to estimate the local control and the overall survival, and the incidence of adverse events. In Phase I, S-1 was administered orally in a split-course fashion as two doses of 40 mg/m 2 , for a total daily dose of 80 mg/m 2 . The course involved a 2-week rest after a 2-week administration (Level 1) and a 1-week rest after a 3-week administration (Level 2). Radiation therapy was administered in 2-Gy daily (total 60-Gy) standard fractionation. Seven patients were enrolled in the Phase I, and 19 in the Phase II study. Mucositis was the most common toxicity encountered. All 26 patients completed radiation therapy without delay. The overall response rate was 100% (26/26) with all patients showing a complete response. One patient developed a local recurrence 28 months after the treatment. The 3-year local control and overall survival rates were 94.7 and 85.4%, respectively (limited to 22 patients from Level 2). The use of S-1 at 80 mg/m 2 per day in a split-course with 1-week rest during the course of radiation therapy was safe and effective for Stage II glottic cancer. The treatment strategy employing orally available S-1 proved to be beneficial over the conventional injection of antitumor agents for maintaining the patients' quality of life. (author)

  4. Advanced Gastric Cancer: Differentiation of Borrmann Type IV versus Borrmann Type III by Two-Phased Dynamic Multi-Detector Row CT with Use of the Water Filling Method

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dae Jung; Yu, Jeong Sik; Lee, Sang Min; Kim, Joo Hee; Chung, Jae Joon; Kim, Ki Whang [Dept. of Radiology, Yonsei University College of Medicine, Gangnam Severance Hospital, Seoul (Korea, Republic of); Kang, Hae Youn [CHA Bundang Medical Center, CHA University, Seongnam (Korea, Republic of)

    2013-02-15

    To characterize Borrmann type IV from Borrmann type III advanced gastric cancer (AGC) by two-phased multi-detector row computed tomography (MDCT) using the water filling method. A total of 143 patients (pathologically confirmed Borrmann type III and IV - 100 and 43 patients), who underwent preoperative MDCT, were enrolled. Two radiologists, retrospectively and independently, determined tumor enhancement pattern using a 5-grade scale without clinical information. A weighted kappa test was applied for interobserver variability. The score of tumor enhancement pattern correlated with Borrmann type as determined by Spearman's correlation coefficient. The accuracy of differentiation of Borrmann type using MDCT was determined by receiver operating characteristic curves. Interobserver agreement (weighted kappa = 0.683) was substantial. The tumor enhancement pattern score showed a significant correlation with Borrmann type (reviewer 1, r = 0.591, p < 0.001; reviewer 2, r = 0.616, p < 0.001). The accuracy for differentiation of Borrmann type on MDCT was 0.86 (p < 0.001) in both reviewers. The sensitivity and specificity of the diagnosis of Borrmann type IV were 79% and 82% in reviewer 1, and 88% and 78% in reviewer 2, respectively. Dual-phased MDCT using the water filling method can differentiate between Borrmann type IV and III AGC with high accuracy.

  5. Design of the randomized, Phase III, QUAZAR AML Maintenance trial of CC-486 (oral azacitidine) maintenance therapy in acute myeloid leukemia.

    Science.gov (United States)

    Roboz, Gail J; Montesinos, Pau; Selleslag, Dominik; Wei, Andrew; Jang, Jun-Ho; Falantes, Jose; Voso, Maria T; Sayar, Hamid; Porkka, Kimmo; Marlton, Paula; Almeida, Antonio; Mohan, Sanjay; Ravandi, Farhad; Garcia-Manero, Guillermo; Skikne, Barry; Kantarjian, Hagop

    2016-02-01

    Older patients with acute myeloid leukemia (AML) have worse rates of complete remission and shorter overall survival than younger patients. The epigenetic modifier CC-486 is an oral formulation of azacitidine with promising clinical activity in patients with AML in Phase I studies. The Phase III, randomized, double-blind, placebo-controlled QUAZAR AML Maintenance trial (CC-486-AML-001) examines CC-486 maintenance therapy (300 mg/day for 14 days of 28-day treatment cycles) for patients aged ≥55 years with AML in first complete remission. The primary end point is overall survival. Secondary end points include relapse-free survival, safety, health-related quality of life and healthcare resource utilization. This trial will investigate whether CC-486 maintenance can prolong remission and improve survival for older patients with AML.

  6. Melphalan, prednisone, thalidomide and defibrotide in relapsed/refractory multiple myeloma: results of a multicenter phase I/II trial.

    Science.gov (United States)

    Palumbo, Antonio; Larocca, Alessandra; Genuardi, Mariella; Kotwica, Katarzyna; Gay, Francesca; Rossi, Davide; Benevolo, Giulia; Magarotto, Valeria; Cavallo, Federica; Bringhen, Sara; Rus, Cecilia; Masini, Luciano; Iacobelli, Massimo; Gaidano, Gianluca; Mitsiades, Constantine; Anderson, Kenneth; Boccadoro, Mario; Richardson, Paul

    2010-07-01

    Defibrotide is a novel orally bioavailable polydisperse oligonucleotide with anti-thrombotic and anti-adhesive effects. In SCID/NOD mice, defibrotide showed activity in human myeloma xenografts. This phase I/II study was conducted to identify the most appropriate dose of defibrotide in combination with melphalan, prednisone and thalidomide in patients with relapsed and relapsed/refractory multiple myeloma, and to determine its safety and tolerability as part of this regimen. This was a phase I/II, multicenter, dose-escalating, non-comparative, open label study. Oral melphalan was administered at a dose of 0.25 mg/kg on days 1-4, prednisone at a dose of 1.5 mg/kg also on days 1-4 and thalidomide at a dose of 50-100 mg/day continuously. Defibrotide was administered orally at three dose-levels: 2.4, 4.8 or 7.2 g on days 1-4 and 1.6, 3.2, or 4.8 g on days 5-35. Twenty-four patients with relapsed/refractory multiple myeloma were enrolled. No dose-limiting toxicity was observed. In all patients, the complete response plus very good partial response rate was 9%, and the partial response rate was 43%. The 1-year progression-free survival and 1-year overall survival rates were 34% and 90%, respectively. The most frequent grade 3-4 adverse events included neutropenia, thrombocytopenia, anemia and fatigue. Deep vein thrombosis was reported in only one patient. This combination of melphalan, prednisone and thalidomide together with defibrotide showed anti-tumor activity with a favorable tolerability. The maximum tolerated dose of defibrotide was identified as 7.2 g p.o. on days 1-4 followed by 4.8 g p.o. on days 5-35. Further trials are needed to confirm the role of this regimen and to evaluate the combination of defibrotide with new drugs.

  7. Optimal scheme of postoperative chemoradiotherapy in rectal cancer: phase III prospective randomized trial

    International Nuclear Information System (INIS)

    Kim, Young Seok; Kim, Jong Hoon; Choi, Eun Kyung

    2002-01-01

    To determine the optimal scheme of postoperative chemoradiotherapy in rectal cancer by comparing survival, patterns of failure, toxicities in early and late radiotherapy groups using a phase III randomized prospective clinical trial. From January 1996 to March 1999, 307 patients with curatively resected AJCC stage II and III rectal cancer were assigned randomly to an 'early (151 patients, arm I)' or a 'late (156 patients, arm II)' and were administered combined chemotherapy (5-FU 375 mg/m 2 /day, leucovorin 20 mg/m 2 , IV bolus daily, for 3 days with RT, 5 days without RT, 8 cycles with 4 weeks interval) and radiation therapy (whole pelvis with 45 Gy/25 fractions/5 weeks). Patients of arm I received radiation therapy from day 1 of the first cycle of chemotherapy and those of arm II from day 57 with a third cycle of chemotherapy. The median follow-up period of living patients was 40 months. Of the 307 patients enrolled, fifty patients did not receive scheduled radiation therapy or chemotherapy. The overall survival rate and disease free survival rate at 5 years were 78.3% and 68.7% in arm I, and 78.4% and 67.5% in arm II. The local recurrence rate was 6.6% and 6.4% (ρ = 0.46) in arms I and II, respectively, no significant difference was observed between the distant metastasis rates of the two arms (23.8% and 29.5%, ρ = 0.16). During radiation therapy, grade 3 diarrhea or more, by the NCI common toxicity criteria, was observed in 63.0% and 58.2% of the respective arms (ρ = N.S.), but most were controlled with supportive care. Hematologic toxicity (leukopenia) greater than RTOG grade 2 was found in only 1.3% and 2.6% of patients in each respective arm. There was no significant difference in survival, patterns of failure or toxicities between the early and late radiation therapy arms. Postoperative adjuvant chemoradiation was found to be a relatively safe treatment but higher compliance is needed

  8. Assessing braze quality in the actively cooled Tore Supra Phase III outboard pump limiter

    International Nuclear Information System (INIS)

    Nygren, R.E.; Lutz, T.L.; Miller, J.D.; McGrath, R.; Dale, G.

    1994-01-01

    The quality of brazing of pyrolytic graphite armor brazed to copper tubes in Tore Supra's Phase III Outboard Pump Limiter was assessed through pre-service qualification testing of individual copper/tile assemblies. The evaluation used non-destructive, hot water transient heating tests performed in the high-temperature, high-pressure flow loop at Sandia's Plasma Materials Test Facility. Surface temperatures of tiles were monitored with an infrared camera as water at 120 degrees C at about 2.07 MPa (300 psi) passed through a tube assembly initially at 30 degrees C. For tiles with braze voids or cracks, the surface temperatures tagged behind those of adjacent well-bonded tiles. Temperature tags were correlated with flaw sizes observed during repairs based upon a detailed 2-D heat transfer analyses. open-quotes Badclose quotes tiles, i.e., temperature tags of 10-20 degrees C depending upon tile's size, were easy to detect and, when removed, revealed braze voids of roughly 50% of the joint area. Eleven of the 14 tubes were rebrazed after bad tiles were detected and removed. Three tubes were rebrazed twice

  9. Radiation therapy for ocular choroidal neovascularization (phase I/II study)

    International Nuclear Information System (INIS)

    Sasai, Keisuke; Murata, Rumi; Mandai, Michiko; Takahashi, Masayo; Hiraoka, Masahiro

    1996-01-01

    Purpose/Objective: Choroidal neovascularization (CNV) is a major cause of severe loss of visual acuity in some ocular diseases such as age-related macular degeneration (ARMD) and angio-streaks. Laser photocoagulation has been used to treat patients with subfoveal neovascular lesions with well demarcated boundaries. However, the treatment method is usually associated with a large decrease in visual acuity. Therefore, indications for this treatment are very limited. Recently, some investigators reported the effect of low dose irradiation on the subretinal neovascular membranes in CNV. We conducted a phase I/II study to determine the toxicity and efficacy of external photon beam radiotherapy in patients with CNV. Materials and Methods: Between April 1994 and July 1995, 36 patients with choroidal neovascularization (34 with ARMD; 2 with angiostreaks) were treated with radiation therapy. Eligibility criteria for this study were as follows: the eyes had subretinal neovascular membranes in the avascular area of the fovea; the neovascular membranes had grown in size in the last 6 months; the best pretreatment corrected visual acuity was worse than (20(25)); there were no large subretinal hemorrhages causing decrease in visual acuity; patients were 50 years or older and had not received laser photocoagulation nor other treatment for this condition. Written informed consent was obtained from all patients. The patients underwent fluorescein angiographic evaluation and documentation of their neovascular disease prior to irradiation. Fluorescein angiography, measurement of the best corrected visual acuity, ophthalmoscopic and biomicroscopic examinations were performed at 1, 3, 6, and 12 months after treatment. Treatment planning was performed using a CT simulator which enables real-time treatment planning from multiple CT slices. The clinical target volume included the macula and optic disc, which received a dose of 10 Gy/5 fractions/1 week (first 18 eyes) or 20 Gy/10 fractions

  10. Development of a chromatographic micro-system for radionuclides analysis in nitric acid media

    International Nuclear Information System (INIS)

    Losno, Marion

    2017-01-01

    Radionuclides analysis is a key point for nuclear waste management and nuclear material control. Several steps of sample modification have to be carried out before measurements in order to avoid any interferences and improve measurement precision. However those different steps are long, irradiating and difficult to achieve in gloveboxes. Moreover they produce liquid and solid waste. The goal of the study is to offer a new alternative to the use of solid phase extraction column for radionuclides separation in hard nitric acid medium. The system will decrease the amount of nuclear waste due to the analysis and automatize the different steps of the analysis. A plastic device made of COC containing a micro solid phase extraction column is first designed. Stationary phase is a poly(AMA-co-EDMA) monolith synthesized in situ. Its structure is adjustable and its functionalization versatile with a high resistance to nitric acid medium. Exchange capacity is 150 mg/g of monolith for TBP and TBP/CMPO column and up to 280 mg/g of monolith in case of DAAP. Exchange coefficients are determined for U(VI), Th(IV), Eu(III) and Nd(III) for 3 different extractants (and Pu(IV) in case of TBP column). Monolith synthesis is transferred in centrifugal device and hydrodynamic behavior studied. U,Th/Eu separation was finally carried out in both classic and centrifugal micro-system on TBP column. (author) [fr

  11. Simultaneous determination of Cr(iii) and Cr(vi) using reversed-phased ion-pairing liquid chromatography with dynamic reaction cell inductively coupled plasma mass spectrometry

    Science.gov (United States)

    Wolf, R.E.; Morrison, J.M.; Goldhaber, M.B.

    2007-01-01

    A method for the simultaneous determination of Cr(iii) and Cr(vi) species in waters, soil leachates and synthetic bio-fluids is described. The method uses reversed-phase ion-pairing liquid chromatography to separate the chromium species and a dynamic reaction cell (DRC??) equipped ICP-MS for detection of chromium. Separation of the chromium species is carried out in less than 2 min. Cr(iii) is complexed with ethylenediaminetetraacetic acid (EDTA) prior to separation by mixing samples with the mobile phase containing 2.0 mM tetrabutylammonium hydroxide (TBAOH), 0.5 mM EDTA (dipotassium salt), and 5% (vol/vol) methanol, adjusted to pH 7.6. The interfering 40Ar 12C+ background peak at mass 52 was reduced by over four orders of magnitude to less than 200 cps by using 0.65 mL min-1 ammonia as a reaction gas and an RPq setting on the DRC of 0.75. Method detection limits (MDLs) of 0.09 ??g L-1 for Cr(iii) and 0.06 ??g L-1 for Cr(vi) were obtained based on peak areas at mass 52 for 50 ??L injections of low level spikes. Reproducibility at 2 ??g L-1 was 3% RSD for 5 replicate injections. The tolerance of the method to various levels of common cations and anions found in natural waters and to matrix constituents found in soil leachates and simulated gastric and lung fluids was tested by performing spike recovery calculations for a variety of samples. ?? The Royal Society of Chemistry.

  12. Firebird-III program description

    International Nuclear Information System (INIS)

    Lin, M.R.; Prawirosochardjo, S.; Rennick, D.F.; Wessman, E.; Blain, R.J.D.; Wilson, J.M.

    1979-09-01

    The FIREBIRD-III digital computer program is a general network code developed primarily for predicting the thermalhydraulic behaviour of CANDU power reactors during a postulated loss-of-coolant accident and the subsequent emergency coolant injection. Because of its flexibility, the code can also be used to solve a large variety of general two-phase flow problems. This report describes the thermalhydraulic models and the computation methods used in the program

  13. Extraction of americium (III) by thermosensitive polymer gel copolymerized with acidic phosphorus compound

    International Nuclear Information System (INIS)

    Takeshita, Kenji; Nakano, Yoshio; Matsumura, Tatsuro

    2001-01-01

    A new gel-liquid extraction using a thermosensitive gel was proposed. The thermosensitive gel shows the conformational change of polymer network with temperature, which is known as the phase transition phenomena of gel. The extraction rate and equilibrium of Am(III) in an aqueous solution containing nitrate ion were measured batchwise by using a thermosensitive gel, N-isopropylacrylamide (NIPA) copolymerized with 2-methacryloyloxy- ethylacidphosphate (MR). The effects of the conformational change of polymer network on the extraction rate and equilibrium were discussed. The distribution ratio of Am(III) showed a large value at higher than LCST (low critical solution temperature; 34degC) and was decreased by the phase transition of gel from shrinking to swelling with decreasing temperature. The extraction of Am(III) in the aqueous solution and the release of Am(III) extracted in the gel were repeated stably by the temperature swing operation between 40 and 3degC. The extraction mechanism of Am(III) was described simply as Am 3+ + 3R - OH=(R-O) 3 Am + 3H + (R-OH: MR). The equilibrium constant at the shrinking state (40degC) was more than 3 times of that at swelling state (3degC). The gel-phase diffusivity of Eu(III) used as a substitute of Am(III) was evaluated as the order of 10 -12 m 2 /s at either of 3 or 40degC, which was similar to those for practical extraction chromatographic resins. The temperature-response of gel for the extraction of Eu(III) was very excellent without delay even for the rapid temperature change at 10degC/min. These results suggest that the extraction and release of Am(III) in an aqueous solution can be controlled by the conformational change of polymer network of thermosensitive gel. (author)

  14. Recovery of copper(II) and chromium(III) from nitrate medium with ...

    African Journals Online (AJOL)

    The solvent extraction of copper(II) and chromium(III) from nitrate medium with salicylideneaniline (HL) is studied as a function of various parameters: pH, concentration of salicylideneaniline, contact time and the nature of anoin (nitrate and sulfate) in aqueous phase. Chromium(III) is not extracted by salicylideneaniline ...

  15. Phase I/II trial of weekly docetaxel and concomitant radiotherapy for squamous cell carcinoma of the head and neck

    International Nuclear Information System (INIS)

    Fujii, Masato; Tsukuda, Mamoru; Kubota, Akira; Kida, Akinori; Okami, Kenji

    2003-01-01

    Docetaxel (DOC) is one of the most promising drugs for head and neck cancer (HNSCC). A phase I/II trial of concurrent DOC and radiation for HNSCC was conducted to estimate the recommended dose schedule of DOC, and then to evaluate the therapeutic benefit based on the response and toxicity of the recommended dose schedule. Patients with squamous cell carcinomas of the head and neck were entered. All the patients received radiation with 2.0 Gy single daily fractions up to 60 Gy. DOC was administered weekly for 6 consecutive weeks during radiotherapy. Dose-limiting toxicities, grade 3/4 mucositis and grade 3 pain, manifested in four patients in level 2, and that dose of DOC, 15 mg/m 2 , was considered the maximum tolerated dose (MTD). The recommended dose was decided as 10 mg/m 2 . The phase II study was conducted using DOC at 10 mg/m 2 . Thirty-nine patients with stage II, III or IV were registered, and 35 patients were eligible, 32 patients were evaluable for the response and 34 patients for the toxicity. The overall response rate was 96.9%. The prognoses of the complete response (CR) patients were statistically better than for the partial response (PR) patients. Grade 3 or 4 adverse events consisted of lymphopenia in 64.7%, mucositis in 41.2% and anorexia in 20.6% of the patients. Thirty-two of the 35 eligible patients showed high compliance of over 90%, and their toxicities were manageable. Even low-dose DOC shows a strong effect on HNSCC in combination with radiation, with high survival rates in CR patients. The effect on survival will be assessed by further follow-up. (author)

  16. Raman spectroscopic study of calcite III to aragonite transformation under high pressure and high temperature

    Science.gov (United States)

    Liu, Chuanjiang; Zheng, Haifei; Wang, Duojun

    2017-10-01

    In our study, a series of Raman experiments on the phase transition of calcite at high pressure and high temperature were investigated using a hydrothermal diamond anvil cell and Raman spectroscopy technique. It was found that calcite I transformed to calcite II and calcite III at pressures of 1.62 and 2.12 GPa and room temperature. With increasing temperature, the phase transition of calcite III to aragonite occurred. Aragonite was retained upon slowly cooling of the system, indicating that the transition of calcite III to aragonite was irreversible. Based on the available data, the phase boundary between calcite III and aragonite was determined by the following relation: P(GPa) = 0.013 × T(°C) + 1.22 (100°C ≤ T ≤ 170°C). It showed that the transition pressure linearly rose with increasing temperature. A better understanding of the stability of calcite III and aragonite is of great importance to further explore the thermodynamic behavior of carbonates and carbon cycling in the mantle.

  17. Alterations in the Rate of Limb Movement Using a Lower Body Positive Pressure Treadmill Do Not Influence Respiratory Rate or Phase III Ventilation

    Directory of Open Access Journals (Sweden)

    Michael J. Buono

    2015-01-01

    Full Text Available The purpose of this study was to determine the effect of alterations in rate of limb movement on Phase III ventilation during exercise, independent of metabolic rate, gait style, and treadmill incline. Subjects completed five submaximal exercise bouts on a lower body positive pressure treadmill (AlterG P 200. The percent body weight for the five exercise bouts was 100, 87, 75, 63, and 50% and each was matched for carbon dioxide production (VCO2. Naturally, to match the VCO2 while reducing the body weight up to 50% of normal required a significant increase in the treadmill speed from 3.0±0.1 to 4.1±0.2 mph, which resulted in a significant (P<0.05 increase in the mean step frequency (steps per minute from 118±10 at 3 mph (i.e., 100% of body weight to 133±6 at 4.1 mph (i.e., 50% of body weight. The most important finding was that significant increases in step frequency did not significantly alter minute ventilation or respiratory rate. Such results do not support an important role for the rate of limb movement in Phase III ventilation during submaximal exercise, when metabolic rate, gait style, and treadmill incline are controlled.

  18. La(III) sorption studies on poly(dibenzo-18-crown-6) for the sequential separation of La(III), Th(IV) and U(VI) in L-arginine

    International Nuclear Information System (INIS)

    Sabale, Sandip; Nikam, Gurunath; Mohite, B.S.

    2010-01-01

    Poly(dibenzo-18-crown-6) is used as a stationary phase to study the sorption behavior of La(III) in L-arginine medium. The quantitative adsorption of La(III) was found at 1 x 10 -4 to 1 x 10 -6 M L-arginine. 1.0-8.0 M HCl, 0.5-8.0 M HBr and HClO 4 were found to be an efficient eluents for La(III). The capacity of crown polymer for La(III) was found to be 1.37±0.01 mmol/g. The tolerance limit of various cations and anions for La(III) was determined. La(III) was quantitatively separated from other metal ions in binary as well as multicomponent mixtures. The study was extended to sequential separation of La(III), U(VI) and Th(IV). The good separation yields were obtained and have good reproducibility (±2%). The method incorporates the determination of La(III) in real sample. The method is simple, rapid and selective. (author)

  19. Social Analysis Systems (SAS2) - Phase III

    International Development Research Centre (IDRC) Digital Library (Canada)

    Scaling Up the International Impact of Action Research : Social Analysis ... up the international impact of action research : SAS phase 3; final technical report ... 000 Canadians abroad to work at the local level on various development issues.

  20. Randomized phase III study comparing paclitaxel/cisplatin/ gemcitabine and gemcitabine/cisplatin in patients with locally advanced or metastatic urothelial cancer without prior systemic therapy: EORTC intergroup study 30987

    NARCIS (Netherlands)

    J. Bellmunt (Joaquim); H. von der Maase (Hans); G.M. Mead (Graham); I. Skoneczna (I.); M. de Santis (Maria); G. Daugaard (Gedske); J. Boehle; C. Chevreau (Christine); L. Paz-Ares (Luis); L.R. Laufman (Leslie); E. Winquist (Eric); R. Raghavan (Raghu); S. Marreaud (Sandrine); S. Collette (Sandra); R. Sylvester (Richard); R. de Wit (Ronald)

    2012-01-01

    textabstractPurpose: The combination of gemcitabine plus cisplatin (GC) is a standard regimen in patients with locally advanced or metastatic urothelial cancer. A phase I/II study suggested that a three-drug regimen that included paclitaxel had greater antitumor activity and might improve survival.

  1. Durability of lightweight concrete : Phase II : wetting and drying tests, Phase III : freezing and thawing tests.

    Science.gov (United States)

    1966-12-01

    This report describes a laboratory research program on the durability of lightweight concrete. Two phases of a three phase study are covered by this report, while the remaining phase is still under study. The two phases being reported are Phase II - ...

  2. Isothiocyanato complexes of Gd(III), Tb(III), Dy(III) and Ho(III) with 2-(2'-pyridyl)benzimidazole

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, A; Singh, V K

    1982-01-01

    Six-coordinated complexes of the type (Ln(PyBzH)/sub 2/NCS.H/sub 2/O) (NCS)/sub 2/.nH/sub 2/O/mC/sub 2/H/sub 5/OH (Ln = Gd(III), Tb(III), Dy(III) and Ho(III), n=1-2; m=1) have been prepared from Ln(NCS)/sub 6//sup 3 -/. The room temperature magnetic moment values confirm the terpositive state of the lanthanide ions. Infrared spectra suggest the N-coordination of thiocyanate group. Electronic spectral studies of Tb(III), Dy(III) and Ho(III) complexes have been made in terms of LSJ term energies. 13 refs.

  3. Analysis of gold(I/III)-complexes by HPLC-ICP-MS demonstrates gold(III) stability in surface waters.

    Science.gov (United States)

    Ta, Christine; Reith, Frank; Brugger, Joël; Pring, Allan; Lenehan, Claire E

    2014-05-20

    Understanding the form in which gold is transported in surface- and groundwaters underpins our understanding of gold dispersion and (bio)geochemical cycling. Yet, to date, there are no direct techniques capable of identifying the oxidation state and complexation of gold in natural waters. We present a reversed phase ion-pairing HPLC-ICP-MS method for the separation and determination of aqueous gold(III)-chloro-hydroxyl, gold(III)-bromo-hydroxyl, gold(I)-thiosulfate, and gold(I)-cyanide complexes. Detection limits for the gold species range from 0.05 to 0.30 μg L(-1). The [Au(CN)2](-) gold cyanide complex was detected in five of six waters from tailings and adjacent monitoring bores of working gold mines. Contrary to thermodynamic predictions, evidence was obtained for the existence of Au(III)-complexes in circumneutral, hypersaline waters of a natural lake overlying a gold deposit in Western Australia. This first direct evidence for the existence and stability of Au(III)-complexes in natural surface waters suggests that Au(III)-complexes may be important for the transport and biogeochemical cycling of gold in surface environments. Overall, these results show that near-μg L(-1) enrichments of Au in environmental waters result from metastable ligands (e.g., CN(-)) as well as kinetically controlled redox processes leading to the stability of highly soluble Au(III)-complexes.

  4. Photoinduced charge transfer phase transition in cesium manganese hexacyanoferrate

    International Nuclear Information System (INIS)

    Matsuda, Tomoyuki; Tokoro, Hiroko; Hashimoto, Kazuhito; Ohkoshi, Shin-ichi

    2007-01-01

    Cesium manganese hexacyanoferrate, Cs 1.51 Mn[Fe(CN) 6 ], shows a thermal phase transition between Mn II -NC-Fe III [high-temperature (HT) phase] and Mn III -NC-Fe II [low-temperature (LT) phase] with phase transition temperatures of 170 K (HT→LT) and 230 K (LT→HT). The LT phase shows ferromagnetism with Curie temperature of 7 K and coercive field of 60 Oe. Irradiating with 532 nm laser light converts the LT phase into the photoinduced (PI) phase, which does not have spontaneous magnetization. The electronic state of the PI phase corresponds to that of the HT phase and the relaxation temperature from the PI to the LT phase is observed at 90 K

  5. Design of Phase II Non-inferiority Trials.

    Science.gov (United States)

    Jung, Sin-Ho

    2017-09-01

    With the development of inexpensive treatment regimens and less invasive surgical procedures, we are confronted with non-inferiority study objectives. A non-inferiority phase III trial requires a roughly four times larger sample size than that of a similar standard superiority trial. Because of the large required sample size, we often face feasibility issues to open a non-inferiority trial. Furthermore, due to lack of phase II non-inferiority trial design methods, we do not have an opportunity to investigate the efficacy of the experimental therapy through a phase II trial. As a result, we often fail to open a non-inferiority phase III trial and a large number of non-inferiority clinical questions still remain unanswered. In this paper, we want to develop some designs for non-inferiority randomized phase II trials with feasible sample sizes. At first, we review a design method for non-inferiority phase III trials. Subsequently, we propose three different designs for non-inferiority phase II trials that can be used under different settings. Each method is demonstrated with examples. Each of the proposed design methods is shown to require a reasonable sample size for non-inferiority phase II trials. The three different non-inferiority phase II trial designs are used under different settings, but require similar sample sizes that are typical for phase II trials.

  6. A new selective chromogenic reagent for the spectrophotometric determination of thallium(I) and (III) and its separation using flotation and the solid-phase extraction on polyurethane foam.

    Science.gov (United States)

    Abou-El-Sherbini, Khaled S; Mostafa, Gamal A E; Hassanien, Mohamed M

    2003-09-01

    A new sensitive chromogenic reagent, 9,10-phenanthaquinone monoethylthiosemicarbazone (PET), has been synthesized and used in the spectrophotometric determination of Tl(III). In HNO3, H2SO4 or H3PO4 acids, PET can react immediately at room temperature with Tl(III) to form a red 2:1 complex with a maximum absorption at 516 nm. The different analytical parameters affecting the extraction and determination processes have been examined. The calibration curve was found to be linear over the range 0.2-10 microg cm(-3) with a molar absorptivity of 2.2 x 10(4) dm3 mol(-1) cm(-1). Sandell's sensitivity was found to be 0.0093 microg cm(-2). No interference from macroamounts of foreign ions was detected, except for Pd(II). However, Pd(II) does not affect the determination process, because its complex with PET has its lambda(max) at 625 nm. The proposed method has been applied to the determination of Tl(I and III) in synthetic and natural samples after separation by flotation (in oleic acid/kerosene) and solid-phase extraction (on polyurethane foam) techniques. The two methods were found to be accurate and not subject to random error, but solid-phase extraction was preferred because it is cheap, simpler and there is no contamination risk coming from flotation reagents.

  7. Can harmonized regulation overcome intra-European differences? Insights from a European Phase III stem cell trial.

    Science.gov (United States)

    Hauskeller, Christine

    2017-09-01

    Harmonized regulation of research with human stem cells in Europe has shaped innovation in regenerative medicine. Findings from a Phase III academic clinical trial of an autologous cell procedure illustrate the obstacles that a multinational trial faces. A typology of the obstacles encountered, may help other teams embarking upon trials. The findings throw light on the situation of clinician-scientists in clinical innovation, as the expertise to run scientific trials is very complex. The innovation route of clinical translation takes insufficient account of the interdependencies between multiple social and cultural factors from outside the laboratory and the clinic. For ethical reasons, however, academic and business routes to stem cell treatments ought to be enabled by the regulators. Suggestions arise, how academics can prepare for trials, that academic research needs better institutional support and that new models of medical innovation may need to be developed for regenerative medicine.

  8. Radiation therapy for ocular choroidal neovascularization (phase I/II study): preliminary report

    International Nuclear Information System (INIS)

    Sasai, Keisuke; Murata, Rumi; Mandai, Michiko; Takahashi, Masayo; Ogura, Yuichiro; Ngata, Yasushi; Nishimura, Yasumasa; Hiraoka, Masahiro

    1997-01-01

    Purpose/Objective: Choroidal neovascularization (CNV) is a major cause of severe loss of visual acuity in some ocular diseases such as age-related macular degeneration (ARMD) and angioid streaks. Laser photocoagulation has been used to treat patients with subfoveal neovascular lesions with well-demarcated boundaries. However, the treatment method is usually associated with a large decrease in visual acuity. Therefore, indications for this treatment are very limited. Recently, some investigators reported the effect of low dose irradiation on the sub retinal neovascular membranes in CNV. We conducted a Phase I/II study to determine the toxicity and efficacy of external photon beam radiotherapy in patients with CNV. Methods and Materials: Between April, 1994 and July, 1995, 36 patients with choroidal neovascularization (34 with ARMD and 2 with angioid streaks) were treated with radiation therapy. Treatment planning was performed using a CT simulator that enables real-time treatment planning from multiple CT slices. The clinical target volume that included the macula and optic disc received a dose of 10 Gy/5 fractions/1 week (first 18 eyes) or 20 Gy/10 fractions/2 weeks (last 18 eyes). All eyes were irradiated with a single lateral 6 MV photon beam, angled 10 degrees posteriorly to exclude the ipsilateral lens and the contralateral eye from the radiation field. The ipsilateral lens was irradiated with less than 10% of the total reference dose. The field size averaged 3.0 x 2.5 cm. Records of the 17 eyes with CNV referred to our hospital in 1993, which satisfied the eligibility criteria for this study, were retrospectively analyzed for comparison. Results: There was no significant acute morbidity. All patients were followed regularly by both ophthalmologists and radiation oncologists. Cataract formation after 1 year of the treatment was observed in one patient who had received a dose of 20 Gy. One patient who had received 20 Gy complained of transient dry-eye sensation

  9. Nanocrystalline Axially Bridged Iron Phthalocyanine Polymeric Conductor: (μ-Thiocyanato(phthalocyaninatoiron(III

    Directory of Open Access Journals (Sweden)

    Eiza Shimizu

    2016-01-01

    Full Text Available Skewered Iron(III phthalocyanine conducting polymer can be constructed with the utilization of axial thiocyanato ligands ((μ-thiocyanato(phthalocyaninatoiron(III; (FeIII(Pc(SCNn thereby creating additional avenues for electron transport through a linear SCN bridge, apart from the intermolecular π-π orbital overlap between the Pc molecules. In this paper, we report on the conversion of bulk FeIII(Pc(SCNn polymeric organic conductor into crystalline nanostructures through horizontal vapor phase growth process. The needle-like nanostructures are deemed to provide more ordered and, thus, more π-π interactive interskewer FeIII(Pc(SCNn polymer orientation, resulting in a twofold increase of its electrical conductivity per materials density unit.

  10. The steam generator programme of PISC III

    International Nuclear Information System (INIS)

    Birac, C.; Herkenrath, H.

    1990-12-01

    The PISC III Actions are intended to extend the results and methodologies of the previous PISC excercises, i.e. the validation of the capabilities of the various examination techniques when used on real defects in real components under real conditions of inspection. Being aware of the important safety role that steam generator tubes play as barrier between primary and secondary cooling system and of the industrial problems that the degradation of these tubes can create, the PISC III Management Board agreed to include in the PISC III Programme a special Action on Steam Generator Tubes Testing (SGT). It was decided to organize the programme in three phases, including Round Robin Tests (RRT): - capability tests on loose tubes, - capability tests on transportable mock-ups, - reliability tests on fixed mock-ups including some interesting SURRY tubes

  11. Phase I/II study of azacitidine and capecitabine/oxaliplatin (CAPOX) in refractory CIMP-high metastatic colorectal cancer: evaluation of circulating methylated vimentin.

    Science.gov (United States)

    Overman, Michael J; Morris, Van; Moinova, Helen; Manyam, Ganiraju; Ensor, Joe; Lee, Michael S; Eng, Cathy; Kee, Bryan; Fogelman, David; Shroff, Rachna T; LaFramboise, Thomas; Mazard, Thibault; Feng, Tian; Hamilton, Stanley; Broom, Bradley; Lutterbaugh, James; Issa, Jean-Pierre; Markowitz, Sanford D; Kopetz, Scott

    2016-10-11

    Hypermethylation of promoter CpG islands (CIMP) has been strongly implicated in chemotherapy resistance and is implicated in the pathogenesis of a subset of colorectal cancers (CRCs) termed CIMP-high. This phase I/II study in CRC (phase II portion restricted to CIMP-high CRC), treated fluoropyrimidine/oxaliplatin refractory patients with azacitidine (75 mg/m2/day subcutaneously D1-5) and CAPOX (capecitibine and oxaliplatin) every three weeks. Twenty-six patients (pts) were enrolled in this study: 15 pts (12 treated at MTD) in phase I and 11 pts in phase II. No dose limiting toxicities were observed. A total of 14 pts were CIMP-high. No responses were seen. CIMP-high status did not correlate with efficacy endpoints [stable disease (SD) or progression-free survival (PFS)] or baseline vimentin methylation level. Changes in vimentin methylation over time did not correlate with efficacy outcomes. Baseline methylated vimentin correlated with tumor volume (PCIMP-high pts, but no objective responses. Serum methylated vimentin may be associated with benefit from a regimen including a hypomethylation agent, although this study is not able to separate a potential prognostic or predictive role for the biomarker.

  12. Structure of the CFA/III major pilin subunit CofA from human enterotoxigenic Escherichia coli determined at 0.90 Å resolution by sulfur-SAD phasing.

    Science.gov (United States)

    Fukakusa, Shunsuke; Kawahara, Kazuki; Nakamura, Shota; Iwashita, Takaki; Baba, Seiki; Nishimura, Mitsuhiro; Kobayashi, Yuji; Honda, Takeshi; Iida, Tetsuya; Taniguchi, Tooru; Ohkubo, Tadayasu

    2012-10-01

    CofA, a major pilin subunit of colonization factor antigen III (CFA/III), forms pili that mediate small-intestinal colonization by enterotoxigenic Escherichia coli (ETEC). In this study, the crystal structure of an N-terminally truncated version of CofA was determined by single-wavelength anomalous diffraction (SAD) phasing using five sulfurs in the protein. Given the counterbalance between anomalous signal strength and the undesired X-ray absorption of the solvent, diffraction data were collected at 1.5 Å resolution using synchrotron radiation. These data were sufficient to elucidate the sulfur substructure at 1.38 Å resolution. The low solvent content (29%) of the crystal necessitated that density modification be performed with an additional 0.9 Å resolution data set to reduce the phase error caused by the small sulfur anomalous signal. The CofA structure showed the αβ-fold typical of type IVb pilins and showed high structural homology to that of TcpA for toxin-coregulated pili of Vibrio cholerae, including spatial distribution of key residues critical for pilin self-assembly. A pilus-filament model of CofA was built by computational docking and molecular-dynamics simulation using the previously reported filament model of TcpA as a structural template. This model revealed that the CofA filament surface was highly negatively charged and that a 23-residue-long loop between the α1 and α2 helices filled the gap between the pilin subunits. These characteristics could provide a unique binding epitope for the CFA/III pili of ETEC compared with other type IVb pili.

  13. A novel solid phase extraction procedure on Amberlite XAD-1180 for speciation of Cr(III), Cr(VI) and total chromium in environmental and pharmaceutical samples

    International Nuclear Information System (INIS)

    Narin, Ibrahim; Kars, Ayse; Soylak, Mustafa

    2008-01-01

    Due to the toxicity of chromium, species depend on their chemical properties and bioavailabilities, speciation of chromium is very important in environmental samples. A speciation procedure for chromium(III), chromium(VI) and total chromium in environmental samples is presented in this work, prior to flame atomic absorption spectrometric determination of chromium. The procedure is based on the adsorption of Cr(III)-diphenylcarbazone complex on Amberlite XAD-1180 resin. After oxidation of Cr(III), the developed solid phase extraction system was applied to determinate the total chromium. Cr(III) was calculated as the difference between the total Cr content and the Cr(VI) content. The analytical conditions for the quantitative recoveries of Cr(VI) on Amberlite XAD-1180 resin were investigated. The effects of some alkaline, earth alkaline, metal ions and also some anions were also examined. Preconcentration factor was found to be 75. The detection limits (LOD) based on three times sigma of the blank (N: 21) for Cr(VI) and total chromium were 7.7 and 8.6 μg/L, respectively. Satisfactory results for the analysis of total chromium in the stream sediment (GBW7310) certified reference material for the validation of the presented method was obtained. The procedure was applied to food, water and pharmaceutical samples successfully

  14. Metalloporphyrin Co(III)TMPyP ameliorates acute, sublethal cyanide toxicity in mice.

    Science.gov (United States)

    Benz, Oscar S; Yuan, Quan; Amoscato, Andrew A; Pearce, Linda L; Peterson, Jim

    2012-12-17

    The formation of Co(III)TMPyP(CN)(2) at pH 7.4 has been shown to be completely cooperative (α(H) = 2) with an association constant of 2.1 (±0.2) × 10(11). The kinetics were investigated by stopped-flow spectrophotometry and revealed a complicated net reaction exhibiting 4 phases at pH 7.4 under conditions where cyanide was in excess. The data suggest molecular HCN (rather than CN(-)) to be the attacking nucleophile around neutrality. The two slower phases do not seem to be present when cyanide is not in excess, and the other two phases have rates comparable to that observed for cobalamin, a known effective cyanide scavenger. Addition of bovine serum albumin (BSA) did not affect the cooperativity of cyanide binding to Co(III)TMPyP, only lowered the equilibrium constant slightly to 1.2 (±0.2) × 10(11) and had an insignificant effect on the observed rate. A sublethal mouse model was used to assess the effectiveness of Co(III)TMPyP as a potential cyanide antidote. The administration of Co(III)TMPyP to sodium cyanide intoxicated mice resulted in the time required for the surviving mice to right themselves from a supine position being significantly decreased (9 ± 2 min) compared to that of the controls (33 ± 2 min). All observations were consistent with the demonstrated antidotal activity of Co(III)TMPyP operating through a cyanide-binding (i.e., scavenging) mechanism.

  15. Creactive protein and interleukin-6 as markers of systemic inflammatory response and as prognostic factors for metastatic colorectal cancer. Data from the randomized phase III NORDIC-VII study

    DEFF Research Database (Denmark)

    Thomsen, M.; Kersten, C.; Sorbye, H.

    2015-01-01

    -6 (IL-6). Methods: The study was based on data from the randomized phase III NORDIC-VII study (Nordic FLOX +/cetuximab as first line treatment of mCRC). The effect of different markers of SIR, including modified Glasgow Prognostic Score (mGPS), derived Neutrophil Lymphocyte Ratio (dNLR), levels...

  16. Facilitated transport of Cr(III) through activated composite membrane containing di-(2-ethylhexyl)phosphoric acid (DEHPA) as carrier agent

    Energy Technology Data Exchange (ETDEWEB)

    Arslan, Gulsin [Department of Chemistry, Selcuk University, 42031, Campus, Konya (Turkey); Tor, Ali, E-mail: ator@selcuk.edu.tr [Department of Environmental Engineering, Selcuk University, 42031 Campus, Konya (Turkey); Cengeloglu, Yunus; Ersoz, Mustafa [Department of Chemistry, Selcuk University, 42031, Campus, Konya (Turkey)

    2009-06-15

    The facilitated transport of chromium(III) through activated composite membrane (ACM) containing di-(2-ethylhexyl) phosphoric acid (DEHPA) was investigated. DEHPA was immobilised by interfacial polymerisation on polysulfone layer which was deposited on non-woven fabric by using spin coater. Then, ACM was characterised by using scanning electron microscopy (SEM), contact angle measurements and atomic force microscopy (AFM). Initially, batch experiments of liquid-liquid distribution of Cr(III) and the extractant (DEHPA) were carried out to determine the appropriate pH of the feed phase and the results showed that maximum extraction of Cr(III) was achieved at a pH of 4. It was also found that Cr(III) and DEHPA reacted in 1/1 molar ratio. The effects of Cr(III) (in feed phase), HCl (in stripping phase) and DEHPA (in ACM) concentrations were investigated. DEHPA concentration varies from 0.1 to 1.0 M and it was determined that the transport of Cr(III) increased with the carrier concentration up to 0.8 M. It was also observed that the transport of Cr(III) through the ACM tended to increase with Cr(III) and HCl concentrations. The stability of ACM was also confirmed with replicate experiments.

  17. Facilitated transport of Cr(III) through activated composite membrane containing di-(2-ethylhexyl)phosphoric acid (DEHPA) as carrier agent

    International Nuclear Information System (INIS)

    Arslan, Gulsin; Tor, Ali; Cengeloglu, Yunus; Ersoz, Mustafa

    2009-01-01

    The facilitated transport of chromium(III) through activated composite membrane (ACM) containing di-(2-ethylhexyl) phosphoric acid (DEHPA) was investigated. DEHPA was immobilised by interfacial polymerisation on polysulfone layer which was deposited on non-woven fabric by using spin coater. Then, ACM was characterised by using scanning electron microscopy (SEM), contact angle measurements and atomic force microscopy (AFM). Initially, batch experiments of liquid-liquid distribution of Cr(III) and the extractant (DEHPA) were carried out to determine the appropriate pH of the feed phase and the results showed that maximum extraction of Cr(III) was achieved at a pH of 4. It was also found that Cr(III) and DEHPA reacted in 1/1 molar ratio. The effects of Cr(III) (in feed phase), HCl (in stripping phase) and DEHPA (in ACM) concentrations were investigated. DEHPA concentration varies from 0.1 to 1.0 M and it was determined that the transport of Cr(III) increased with the carrier concentration up to 0.8 M. It was also observed that the transport of Cr(III) through the ACM tended to increase with Cr(III) and HCl concentrations. The stability of ACM was also confirmed with replicate experiments.

  18. Complexes of 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III)

    International Nuclear Information System (INIS)

    Ferenc, W.; Bernat, M; Gluchowska, H.W.; Sarzynski, J.

    2010-01-01

    The complexes of 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III) have been synthesized as polycrystalline hydrated solids, and characterized by elemental analysis, spectroscopy, magnetic studies and also by X-ray diffraction and thermogravimetric measurements. The analysed complexes have the following colours: violet for Nd(III), white for Gd(III) and cream for Ho(III) compounds. The carboxylate groups bind as bidentate chelating (Ho) or bridging ligands (Nd, Gd). On heating to 1173K in air the complexes decompose in several steps. At first, they dehydrate in one step to form anhydrous salts, that next decompose to the oxides of respective metals. The gaseous products of their thermal decomposition in nitrogen were also determined and the magnetic susceptibilities were measured over the temperature range of 76-303K and the magnetic moments were calculated. The results show that 4-chlorophenoxyacetates of Nd(III), Gd(III) and Ho(III) are high-spin complexes with weak ligand fields. The solubility value in water at 293K for analysed 4-chlorophenoxyacetates is in the order of 10 -4 mol/dm 3 . (author)

  19. Species dependent radiotracer study of Cr(VI) and Cr(III) using an aqueous biphasic system

    Energy Technology Data Exchange (ETDEWEB)

    Roy, K.; Lahiri, S. [Chemical Sciences Div., Saha Inst. of Nuclear Physics, Kolkata (India)

    2008-07-01

    The speciation study of Cr(III) and Cr(VI) was carried out using a polyethylene glycol (PEG) based aqueous biphasic extraction system (ABS). Neutron activated Cr(III) and Cr(VI) salts were assayed in a HPGe detector before and after employing aqueous biphasic extraction. Different salts of various salting out abilities were taken as the salt rich phase. The best condition for extraction of Cr(VI) and the maximum differential attitude of ABS to Cr(VI) and Cr(III) was observed when 2 M Na{sub 2}SO{sub 4} and PEG 4000 (50% w/w) solutions were used. Cr(III) can also be extracted by the PEG with prior complexation with diphenylthiocarbazone (dithizone). The chromium dithizonate complex is quantitatively extracted by the PEG rich phase. (orig.)

  20. Integrated Sensing & Controls for Coal Gasification - Development of Model-Based Controls for GE's Gasifier & Syngas Cooler. Topical Rerport for Phase III

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Aditya

    2011-02-17

    This Topical Report for the final Phase III of the program summarizes the results from the Task 3 of the program. In this task, the separately designed extended Kalman Filter (EKF) and model predictive controls (MPC) with ideal sensing, developed in Phase II, were integrated to achieve the overall sensing and control system for the gasification section of an IGCC plant. The EKF and MPC algorithms were updated and re-tuned to achieve closed-loop system stability as well as good steady-state and transient control response. In particular, the performance of the integrated EKF and MPC solution was tested extensively through multiple simulation studies to achieve improved steady-state as well as transient performance, with coal as well as coal-petcoke blended fuel, in the presence of unknown modeling errors as well as sensor errors (noise and bias). The simulation studies demonstrated significant improvements in steady state and transient operation performance, similar to that achieved by MPC with ideal sensors in Phase II of the program.

  1. Thermodynamics of the extraction of Eu(III) and Am(III) with synergistic mixtures of thenoyltrifluoroacetone and a linear polyether

    International Nuclear Information System (INIS)

    Ensor, D.D.; Shah, A.H.

    1983-01-01

    The extractions of trivalent lanthanides and actinides by synergistic mixtures of thenoyltrifluoroacetone (HTTA) and a variety of neutral oxygen donors are well documented. The large increase in the extent of extraction of the metal ion into the organic phase is believed to occur by one of three possible mechanisms. The first involves the direct replacement of residual waters of hydration on the metal by the neutral donor. In the second proposed mechanism, the residual waters remain attached to the metal and the neutral oxygen donor hydrogen bond to the complex through the waters. The final mechanism assumes the complex is not hydrated and the addition of the neutral donor requires the metal to increase its coordination number. A recent review of the synergistic effect showed that the proper interpretation of the mechanism requires the measurement of ΔH and ΔS for the reaction. The synergistic capabilities of a linear polyether, 1,13-bis-[8-quinolyl]-1,4,7,10,13-pentaoxotridecane (K-5), in combination with HTTA to extract Am(III) and Eu(III) have been recently reported by the investigators. The presence of the K-5 in the organic phase not only increased the extraction of the trivalent metals, but also showed a preference for Am(III) over Eu(III). This result was surprising since most neutral donors do not alter the selectivity of HTTA. In an effort to better understand the synergistic mechanism of the K-5/HTTA system, the thermodynamic parameters have been measured by a temperature variation method, and results are reported in this paper. 7 references

  2. Post-treatment resistance analysis of hepatitis C virus from phase II and III clinical trials of ledipasvir/sofosbuvir.

    Science.gov (United States)

    Wyles, David; Dvory-Sobol, Hadas; Svarovskaia, Evguenia S; Doehle, Brian P; Martin, Ross; Afdhal, Nezam H; Kowdley, Kris V; Lawitz, Eric; Brainard, Diana M; Miller, Michael D; Mo, Hongmei; Gane, Edward J

    2017-04-01

    Ledipasvir/sofosbuvir combination treatment in phase III clinical trials resulted in sustained viral suppression in 94-99% of patients. This study characterized drug resistance in treatment failures, which may help to inform retreatment options. We performed NS5A and NS5B deep sequencing of hepatitis C virus (HCV) from patients infected with genotype (GT) 1 who participated in ledipasvir/sofosbuvir phase II and III clinical trials. Fifty-one of 2144 (2.4%) (42 GT1a and 9 GT1b) treated patients met the criteria for resistance analysis due to virologic failure following the end of treatment. The majority of patients with virologic failure (38 of 51; 74.5%) had detectable ledipasvir-specific resistance-associated substitutions (RASs) at the time of virologic failure (1% deep sequencing cut-off). The percent of patients with NS5A RASs at virologic failure were 37.5%, 66.7%, 94.7% and 100% in patients treated for 6, 8, 12 and 24weeks, respectively. The common substitutions detected at failure were Q30R/H, and/or Y93H/N in GT1a and Y93H in GT1b. At failure, 35.3% (18/51) of virologic failure patients' viruses had two or more NS5A RASs and the majority of patients harbored NS5A RASs conferring a 100-1000-fold (n=10) or >1000-fold (n=23) reduced susceptibility to ledipasvir. One patient in a phase II study with a known ledipasvir RAS at baseline (L31M) developed the S282T sofosbuvir (NS5B) RAS at failure. In GT1 HCV-infected patients treated with ledipasvir/sofosbuvir±ribavirin, virologic failure was rare. Ledipasvir resistance in NS5A was selected or enhanced in most patients with virologic failure, one of whom also developed resistance to sofosbuvir. Clinical studies have shown that combination treatment with ledipasvir/sofosbuvir efficiently cures most patients with genotype 1 hepatitis C infection. For the few patients failing treatment, we show that resistance to ledipasvir was observed in most patients, whereas resistance to sofosbuvir was less common. This has

  3. Effect of silodosin on specific urinary symptoms associated with benign prostatic hyperplasia: analysis of international prostate symptom scores in 2 phase III clinical studies

    OpenAIRE

    Gittelman, Marc C; Marks, Leonard S; Hill, Lawrence A; Volinn, Weining; Hoel, Gary

    2010-01-01

    Marc C Gittelman1, Leonard S Marks2, Lawrence A Hill3, Weining Volinn3, Gary Hoel31South Florida Medical Research, Aventura, Florida, USA; 2University of California at Los Angeles and Urological Sciences Research Foundation, Los Angeles, California, USA; 3Watson Laboratories, Salt Lake City, Utah, USAPurpose: Pooled results from 2 randomized, placebo-controlled, US phase III studies (NCT00224107, NCT00224120) showed that silodosin, a uroselective α-blocker, significantly improved In...

  4. SIMMER-III applications to fuel-coolant interactions

    Energy Technology Data Exchange (ETDEWEB)

    Morita, K.; Kondo, Sa.; Tobita, Y.; Brear, D.J. [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

    1998-01-01

    The main purpose of the SIMMER-III code is to provide a numerical simulation of complex multiphase, multicomponent flow problems essential to investigate core disruptive accidents in liquid-metal fast reactors (LMFRs). However, the code is designed to be sufficiently flexible to be applied to a variety of multiphase flows, in addition to LMFR safety issues. In the present study, some typical experiments relating to fuel-coolant interactions (FCIs) have been analyzed by SIMMER-III to demonstrate that the code is applicable to such complex and highly transient multiphase flow situations. It is shown that SIMMER-III can reproduce the premixing phase both in water and sodium systems as well as the propagation of steam explosion. It is thus demonstrated the code is basically capable of simulating integral multiphase thermal-hydraulic problems included in FCI experiments. (author)

  5. A comparison of liquid and solid culture for determining relapse and durable cure in phase III TB trials for new regimens.

    Science.gov (United States)

    Phillips, Patrick P J; Mendel, Carl M; Nunn, Andrew J; McHugh, Timothy D; Crook, Angela M; Hunt, Robert; Bateson, Anna; Gillespie, Stephen H

    2017-11-24

    Tuberculosis kills more people than any other infectious disease, and new regimens are essential. The primary endpoint for confirmatory phase III trials for new regimens is a composite outcome that includes bacteriological treatment failure and relapse. Culture methodology is critical to the primary trial outcome. Patients in clinical trials can have positive cultures after treatment ends that may not necessarily indicate relapse, which was ascribed previously to laboratory cross-contamination or breakdown of old lesions. Löwenstein-Jensen (LJ) medium was the previous standard in clinical trials, but almost all current and future trials will use the Mycobacteria Growth Indicator Tube (MGIT) system due to its simplicity and consistency of use, which will affect phase III trial results. LJ was used for the definition of the primary endpoint in the REMoxTB trial, but every culture was also inoculated in parallel into the MGIT system. The data from this trial, therefore, provide a unique opportunity to investigate and compare the incidence of false 'isolated positives' in liquid and solid media and their potential impact on the primary efficacy results. All post-treatment positive cultures were reviewed in the REMoxTB clinical trial. Logistic regression models were used to model the incidence of isolated positive cultures on MGIT and LJ. A total of 12,209 sputum samples were available from 1652 patients; cultures were more often positive on MGIT than LJ. In 1322 patients with a favourable trial outcome, 126 (9.5%) had cultures that were positive in MGIT compared to 34 (2.6%) patients with positive cultures on LJ. Among patients with a favourable outcome, the incidence of isolated positives on MGIT differed by study laboratory (p cultures in some patients even after adjusting for laboratory, p cultures, positive MGIT cultures were more likely to be associated with higher grade TB symptoms reported within 7 days either side of sputum collection in patients with an

  6. Avelumab (anti-PD-L1) in platinum-resistant/refractory ovarian cancer: JAVELIN Ovarian 200 Phase III study design.

    Science.gov (United States)

    Pujade-Lauraine, Eric; Fujiwara, Keiichi; Dychter, Samuel S; Devgan, Geeta; Monk, Bradley J

    2018-03-27

    Avelumab is a human anti-PD-L1 checkpoint inhibitor with clinical activity in multiple solid tumors. Here, we describe the rationale and design for JAVELIN Ovarian 200 (NCT02580058), the first randomized Phase III trial to evaluate the role of checkpoint inhibition in women with ovarian cancer. This three-arm trial is comparing avelumab administered alone or in combination with pegylated liposomal doxorubicin versus pegylated liposomal doxorubicin alone in patients with platinum-resistant/refractory recurrent ovarian, fallopian tube or peritoneal cancer. Eligible patients are not preselected based on PD-L1 expression and may have received up to three prior lines of chemotherapy for platinum-sensitive disease, but none for resistant disease. Overall survival and progression-free survival are primary end points, and secondary end points include biomarker evaluations and pharmacokinetics.

  7. Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-[(1H-benzimidazol-2-yl-methylene) amino] phenol

    International Nuclear Information System (INIS)

    Omprakash, K.L.; Chandra Pal, A.V.; Reddy, M.L.N.

    1982-01-01

    A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO 4 ) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (logβ 2 ) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III). (author)

  8. Formation constants of Sm(III), Dy(III), Gd(III), Pr(III) and Nd(III) complexes of tridentate schiff base, 2-((1H-benzimidazol-2-yl-methylene) amino) phenol

    Energy Technology Data Exchange (ETDEWEB)

    Omprakash, K L; Chandra Pal, A V; Reddy, M L.N. [Osmania Univ., Hyderabad (India). Dept. of Chemistry

    1982-03-01

    A new tridentate schiff base, 2- (1H-benzimidazol-2-yl-methylene)amino phenol derived from benzimididazole-2-carbo-xaldehyde and 2-aminophenol has been synthesised and characterised by spectral and analytical data. Proton-ligand formation constants of the schiff base and metal-ligand formation constants of its complexes with Sm(III), Dy(III), Gd(III), Nd(III) and Pr(III) have been determined potentiometrically in 50% (v/v) aqueous dioxane at an ionic strength of 0.1M (NaClO/sub 4/) and at 25deg C using the Irving-Rossotti titration technique. The order of stability constants (log..beta../sub 2/) is found to be Sm(III)>Dy(III)>Gd(III)>Pr(III)>Nd(III).

  9. Synthesis, structure, luminescent, and magnetic properties of carbonato-bridged Zn(II)2Ln(III)2 complexes [(μ4-CO3)2{Zn(II)L(n)Ln(III)(NO3)}2] (Ln(III) = Gd(III), Tb(III), Dy(III); L(1) = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato, L(2) = N,N'-bis(3-ethoxy-2-oxybenzylidene)-1,3-propanediaminato).

    Science.gov (United States)

    Ehama, Kiyomi; Ohmichi, Yusuke; Sakamoto, Soichiro; Fujinami, Takeshi; Matsumoto, Naohide; Mochida, Naotaka; Ishida, Takayuki; Sunatsuki, Yukinari; Tsuchimoto, Masanobu; Re, Nazzareno

    2013-11-04

    of Zn(II)2Dy(III)2 were not detected. The fine structure assignable to the (5)D4 → (7)F6 transition of ZnTb1 and ZnTb2 is in good accord with the energy pattern from the magnetic analysis. The Zn(II)2Ln(III)2 complexes (Ln(III) = Tb(III), Dy(III)) showed an out-of-phase signal with frequency-dependence in alternating current susceptibility, indicative of single molecule magnet. Under a dc bias field of 1000 Oe, the signals become significantly more intense and the energy barrier, Δ/kB, for the magnetic relaxation was estimated from the Arrhenius plot to be 39(1) and 42(8) K for ZnTb1 and ZnTb2, and 52(2) and 67(2) K for ZnDy1 and ZnDy2, respectively.

  10. Bottlenecks in the development of topical analgesics: molecule, formulation, dose-finding, and phase III design

    Directory of Open Access Journals (Sweden)

    Keppel Hesselink JM

    2017-03-01

    Full Text Available Jan M Keppel Hesselink,1 David J Kopsky,2 Stephen M Stahl3 1Institute Neuropathic Pain, Bosch en Duin, the Netherlands; 2Institute Neuropathic Pain, Amsterdam, the Netherlands; 3University of California San Diego, La Jolla, CA, USA Abstract: Topical analgesics can be defined as topical formulations containing analgesics or co-analgesics. Since 2000, interest in such formulations has been on the rise. There are, however, four critical issues in the research and development phases of topical analgesics: 1 The selection of the active pharmaceutical ingredient. Analgesics and co-analgesics differ greatly in their mechanism of action, and it is required to find the most optimal fit between such mechanisms of action and the pathogenesis of the targeted (neuropathic pain. 2 Issues concerning the optimized formulation. For relevant clinical efficacy, specific characteristics for the selected vehicle (eg, cream base or gel base are required, depending on the physicochemical characteristics of the active pharmaceutical ingredient(s to be delivered. 3 Well-designed phase II dose-finding studies are required, and, unfortunately, such trials are missing. In fact, we will demonstrate that underdosing is one of the major hurdles to detect meaningful and statistically relevant clinical effects of topical analgesics. 4 Selection of clinical end points and innovatively designed phase III trials. End point selection can make or break a trial. For instance, to include numbness together with tingling as a composite end point for neuropathic pain seems stretching the therapeutic impact of an analgesic too far. Given the fast onset of action of topical analgesics (usually within 30 minutes, enrichment designs might enhance the chances for success, as the placebo response might decrease. Topical analgesics may become promising inroads for the treatment of neuropathic pain, once sufficient attention is given to these four key aspects. Keywords: topical, analgesics

  11. Phase I/II Study of Metastatic Melanoma Patients Treated with Nivolumab Who Had Progressed after Ipilimumab.

    Science.gov (United States)

    Weber, Jeffrey; Gibney, Geoffrey; Kudchadkar, Ragini; Yu, Bin; Cheng, Pingyan; Martinez, Alberto J; Kroeger, Jodie; Richards, Allison; McCormick, Lori; Moberg, Valerie; Cronin, Heather; Zhao, Xiuhua; Schell, Michael; Chen, Yian Ann

    2016-04-01

    The checkpoint inhibitor nivolumab is active in patients with metastatic melanoma who have failed ipilimumab. In this phase I/II study, we assessed nivolumab's safety in 92 ipilimumab-refractory patients with unresectable stage III or IV melanoma, including those who experienced grade 3-4 drug-related toxicity to ipilimumab. We report long-term survival, response duration, and biomarkers in these patients after nivolumab treatment (3 mg/kg) every 2 weeks for 24 weeks, then every 12 weeks for up to 2 years, with or without a multipeptide vaccine. The response rate for ipilimumab-refractory patients was 30% (95% CI, 21%-41%). The median duration of response was 14.6 months, median progression-free survival was 5.3 months, and median overall survival was 20.6 months, when patients were followed up for a median of 16 months. One- and 2-year survival rates were 68.4% and 31.2%, respectively. Ipilimumab-naïve and ipilimumab-refractory patients showed no significant difference in survival. The 21 patients with prior grade 3-4 toxicity to ipilimumab that was managed with steroids tolerated nivolumab well, with 62% (95% CI, 38%-82%) having complete or partial responses or stabilized disease at 24 weeks. High numbers of myeloid-derived suppressor cells (MDSC) were associated with poor survival. Thus, survival and long-term safety were excellent in ipilimumab-refractory patients treated with nivolumab. Prior grade 3-4 immune-related adverse effects from ipilimumab were not indicative of nivolumab toxicities, and patients had a high overall rate of remission or stability at 24 weeks. Prospectively evaluating MDSC numbers before treatment could help assess the expected benefit of nivolumab. ©2016 American Association for Cancer Research.

  12. Solvent extraction of lanthanide ions with 1-Phenyl-3-Methyl-4-Benzoyl-Pyrazolone-5 (HPMBP), 2. Extraction of Erbium(III), Ytterbium(III) and Lutetium(III) by HPMBP from aqueous-methanol solutions

    International Nuclear Information System (INIS)

    Czakis-Sulikowska, D.M.; Kuznik, B.; Malinowska, A.

    1990-01-01

    The solvent extraction of lanthanides(III)(Ln = Er, Yb, Lu) by 1-phenyl-3-methyl-4-benzoyl-pyrazolone-5 (HL) in carbon tetrachloride from aqueous-methanol phase was investigated. The equilibrium constants for the extraction from aqueous-50 % (ν/ν) methanol phase (K ex ), two-phase stability constants of the complexes LnL 3 (β 3 * ) and stability constants of complexes LnL 2+ , LnL 2 + , LnL 3 (β n )(Ln = Yb, Lu) were calculated. It was confirmed that the addition of methanol to the aqueous phase causes a synergistic effect. The influence of methanol on the dissociation constant of HPMBP (K a ) and the distribution constant of HPMBP (p HL ) between carbon tetrachloride and water-methanol solutions was investigated. (Authors)

  13. Spectrophotometric and pH-Metric Studies of Ce(III, Dy(III, Gd(III,Yb(III and Pr(III Metal Complexes with Rifampicin

    Directory of Open Access Journals (Sweden)

    A. N. Sonar

    2011-01-01

    Full Text Available The metal-ligand and proton-ligand stability constant of Ce(III, Dy(III, Gd(III,Yb(III and Pr(III metals with substituted heterocyclic drug (Rifampicin were determined at various ionic strength by pH metric titration. NaClO4 was used to maintain ionic strength of solution. The results obtained were extrapolated to the zero ionic strength using an equation with one individual parameter. The thermodynamic stability constant of the complexes were also calculated. The formation of complexes has been studied by Job’s method. The results obtained were of stability constants by pH metric method is confirmed by Job’s method.

  14. Complexes of lanthanum(III), cerium(III), samarium(III) and dysprosium(III) with substituted piperidines

    Energy Technology Data Exchange (ETDEWEB)

    Manhas, B S; Trikha, A K; Singh, H; Chander, M

    1983-11-01

    Complexes of the general formulae M/sub 2/Cl/sub 6/(L)/sub 3/.C/sub 2/H/sub 5/OH and M/sub 2/(NO/sub 3/)/sub 6/(L)/sub 2/.CH/sub 3/OH have been synthesised by the reactions of chlorides and nitrates of La(III), Ce(III), Sm(III) and Dy(III) with 2-methylpiperidine, 3-methylpiperidine and 4-methylpiperidine. These complexes have been characterised on the basis of their elemental analysis, and IR and electronic reflectance spectra. IR spectral data indicate the presence of coordinated ethanol and methanol molecules and bidentate nitrate groups. Coordination numbers of the metal ions vary from 5 to 8. 19 refs.

  15. The crystal structure and the phase transitions of pyridinium trifluoromethanesulfonate

    International Nuclear Information System (INIS)

    Jesariew, Dominik; Ilczyszyn, Maria M; Pietraszko, Adam

    2014-01-01

    The calorimetric and optical studies and the structural properties of pyridinium trifluoromethanesulfonate (abbreviated as PyHOTf) are reported. A sequence of four fully reversible solid–solid phase transitions, at 223.0, 309.0, 359.9 and 394.3 K, has been discovered. The phase transition sequence was confirmed by x-ray diffraction data. The crystal structures of three phases (V, IV and III) have been determined from the single crystal x-ray diffraction data. Structural properties of the high temperature phases are characterized using powder x-ray diffraction data measured in the 290–425 K temperature range. The structural changes triggered by the temperature change are discussed in relation to the phase transitions. Two low temperature phases (V and IV) belong to the P4 3 2 1 2 space group of the tetragonal system. The intermediate phases (III and II) are monoclinic and the prototype high temperature phase (I) is a pseudo-cubic (tetragonal) one. The low temperature phases (V and IV) are well ordered. The crystal structure of intermediate (III and II) and prototype (I) phases are characterized by high disorder of the pyridinium cations and triflate anions. (papers)

  16. The use of dihexyldithiocarbamate in reverse-phase HPLC of metal chelates

    Science.gov (United States)

    Fatimah, S. S.; Bahti, H. H.; Hastiawan, I.; Permanasari, A.

    2018-05-01

    Dialkyldithiocarbamates have long been used as chelating agents in reverse-phase HPLC of transition metals. In the previous study, an alkyl homolog of this type of ligand, namely dihexyldithiocarbamate (DHDTC), was synthesized and characterized. The use of this particular ligand in the revese-phase HPLC of some selected transition metal ions is now reported for the first time. The mobile phase comprising of the flow rate and of the detection, in the separation of the metal chelates of Cd (II), Fe (III), Cu (II), and Co (III), were investigated on a C-18 column. The results showed that dihexylditiocarbamate could be used for separating Cd (II), Fe(III), Cu(II), and Co(III). Therefore, it could be used in simultaneous analysis.

  17. Alterations in the Rate of Limb Movement Using a Lower Body Positive Pressure Treadmill Do Not Influence Respiratory Rate or Phase III Ventilation

    OpenAIRE

    Michael J. Buono; Marissa Burnsed-Torres; Bethany Hess; Kristine Lopez; Catherine Ortiz; Ariel Girodo; Karen Lolli; Brett Bloom; David Bailey; Fred W. Kolkhorst

    2015-01-01

    The purpose of this study was to determine the effect of alterations in rate of limb movement on Phase III ventilation during exercise, independent of metabolic rate, gait style, and treadmill incline. Subjects completed five submaximal exercise bouts on a lower body positive pressure treadmill (AlterG P 200). The percent body weight for the five exercise bouts was 100, 87, 75, 63, and 50% and each was matched for carbon dioxide production (V CO2 ). Naturally, to match the V CO2 while reducin...

  18. Phase III double-blind evaluation of an aloe vera gel as a prophylactic agent for radiation-induced skin toxicity

    International Nuclear Information System (INIS)

    Williams, Maureen S.; Burk, Mary; Loprinzi, Charles L.; Hill, Mary; Schomberg, Paula J.; Nearhood, Kim; O'Fallon, Judith R.; Laurie, John A.; Shanahan, Thomas G.; Moore, Randy L.; Urias, Rodolfo E.; Kuske, Robert R.; Engel, Roland E.; Eggleston, William D.

    1996-01-01

    Purpose: Considerable pilot data and clinical experience suggested that an aloe vera gel might help to prevent radiation therapy-induced dermatitis. Methods and Materials: Two Phase III randomized trials were conducted. The first one was double blinded, utilized a placebo gel, and involved 194 women receiving breast or chest wall irradiation. The second trial randomized 108 such patients to aloe vera gel vs. no treatment. Skin dermatitis was scored weekly during both trials both by patients and by health care providers. Results: Skin dermatitis scores were virtually identical on both treatment arms during both of the trials. The only toxicity from the gel was rare contact dermatitis. Conclusions: This dose and schedule of an aloe vera gel does not protect against radiation therapy-induced dermatitis

  19. Inner-sphere and outer-sphere complexes of yttrium(III), lanthanum (III), neodymium(III), terbium(III) and thulium(III) with halide ions in N,N-dimethylformamide

    International Nuclear Information System (INIS)

    Takahashi, Ryouta; Ishiguro, Shin-ichi

    1991-01-01

    The formation of chloro, bromo and iodo complexes of yttrium(III), and bromo and iodo complexes of lanthanum(III), neodymium(III), terbium(III) and thulium(III) has been studied by precise titration calorimetry in N,N-dimethylformamide (DMF) at 25 o C. The formation of [YCl] 2+ , [YCl 2 ] + , [YCl 3 ] and [YCl 4 ] - , and [MBr] 2+ and [MBr 2 ] + (M = Y, La, Nd, Tb, Tm) was revealed, and their formation constants, enthalpies and entropies were determined. It is found that the formation enthalpies change in the sequence ΔH o (Cl) > ΔH o (l), which is unusual for hard metal (III) ions. This implies that, unlike the chloride ion, the bromide ion forms outer-sphere complexes with the lanthanide(III) and yttrium(III) ions in DMF. Evidence for either an inner- or outer-sphere complex was obtained from 89 Y NMR spectra for Y(ClO 4 ) 3 , YCl 3 and YBr 3 DMF solutions at room temperature. (author)

  20. Biofilms and type III secretion are not mutually exclusive in Pseudomonas aeruginosa

    DEFF Research Database (Denmark)

    Mikkelsen, H; Bond, N J; Skindersoe, M E

    2009-01-01

    in exponential phase than to those in stationary phase. In the current study, we investigated how these conditions influence the production of virulence factors using a transcriptomic approach. Our results show that biofilms express the type III secretion system, whereas planktonic cells do not...

  1. Th(As(III)4As(V)4O18): a mixed-valent oxoarsenic(III)/arsenic(V) actinide compound obtained under extreme conditions.

    Science.gov (United States)

    Yu, Na; Klepov, Vladislav V; Kegler, Philip; Bosbach, Dirk; Albrecht-Schmitt, Thomas E; Alekseev, Evgeny V

    2014-08-18

    A high-temperature/high-pressure method was employed to investigate phase formation in the Th(NO3)4·5H2O-As2O3-CsNO3 system. It was observed that an excess of arsenic(III) in starting system leads to the formation of Th(As(III)4As(V)4O18), which is representative of a rare class of mixed-valent arsenic(III)/arsenic(V) compounds. This compound was studied with X-ray diffraction, energy-dispersive X-ray, and Raman spectroscopy methods. Crystallographic data show that Th(As(III)4As(V)4O18) is built from (As(III)4As(V)4O18)(4-) layers connected through Th atoms. The arsenic layers are found to be isoreticular to those in previously reported As2O3 and As3O5(OH), and the geometric differences between them are discussed. Bands in the Raman spectrum are assigned with respect to the presence of AsO3 and AsO4 groups.

  2. Analysis of Regional Timelines To Set Up a Global Phase III Clinical Trial in Breast Cancer: the Adjuvant Lapatinib and/or Trastuzumab Treatment Optimization Experience

    OpenAIRE

    Metzger-Filho, Otto; Azambuja, Evandro de; Bradbury, Ian; Saini, Kamal S.; Bines, Jose; Simon, Sergio D. [UNIFESP; Van Dooren, Veerle; Aktan, Gursel; Pritchard, Kathleen I.; Wolff, Antonio C.; Smith, Ian; Jackisch, Christian; Lang, Istvan; Untch, Michael; Boyle, Frances

    2013-01-01

    Purpose. This study measured the time taken for setting up the different facets of Adjuvant Lapatinib and/or Trastuzumab Treatment Optimization (ALTTO), an international phase III study being conducted in 44 participating countries.Methods. Time to regulatory authority (RA) approval, time to ethics committee/institutional review board (EC/IRB) approval, time from study approval by EC/IRB to first randomized patient, and time from first to last randomized patient were prospectively collected i...

  3. Combining dosimetry and toxicity: analysis of two UK phase III clinical trials

    International Nuclear Information System (INIS)

    Gulliford, Sarah L

    2014-01-01

    There are many advantages to performing a clinical trial when implementing a novel radiotherapy technique. The clinical trials framework enables the safety and efficacy of the 'experimental arm' to be tested and ensures practical support, rigorous quality control and data monitoring for participating centres. In addition to the clinical and follow-up data collected from patients within the trial, it is also possible to collect 3-D dosimetric information from the corresponding radiotherapy treatment plans. Analysing the combination of dosimetric, clinical and follow-up data enhances the understanding of the relationship between the dose delivered to both the target and normal tissue structures and reported outcomes and toxicity. Aspects of the collection, collation and analysis of data from two UK multicentre Phase III radiotherapy trials are presented here. MRC-RT01 dose-escalation prostate radiotherapy trial ISRCTN47772397 was one of the first UK multi-centre radiotherapy trials to collect 3-D dosimetric data. A number of different analysis methodologies were implemented to investigate the relationship between the dose distribution to the rectum and specific rectal toxicities. More recently data was collected from the PARSPORT trial (Parotid Sparing IMRT vs conventional head and neck radiotherapy) ISRCTN48243537. In addition to the planned analysis, dosimetric analysis was employed to investigate an unexpected finding that acute fatigue was more prevalent in the IMRT arm of the trial. It can be challenging to collect 3-D dosimetric information from multicentre radiotherapy trials. However, analysing the relationship between dosimetric and toxicity data provides invaluable information which can influence the next generation of radiotherapy techniques.

  4. Equilibrium Model for the Extraction of Am(III), Eu(III), and HNO{sub 3} into DMDOHEMA in TPH

    Energy Technology Data Exchange (ETDEWEB)

    Geist, Andreas [Forschungszentrum Karlsruhe, Institut fuer Nukleare Entsorgung, P.O. Box 3640, 76021 Karlsruhe (Germany)

    2008-07-01

    The extraction of americium(III), europium(III), and nitric acid into DMDOHEMA (N,N'-dimethyl-N,N'-di-octyl-2-[2-hexyl-oxy-ethyl]-malonamide) dissolved in TPH (a kerosene-type diluent) was studied as a function of initial nitric acid and DMDOHEMA concentrations. Nitric acid extraction can be described by the formation of three complexes, HNO{sub 3}-L{sub 2}, HNO{sub 3}-L, and (HNO{sub 3}){sub 2}-L. Americium(III) extraction is best described by the formation of three complexes, Am(NO{sub 3}){sub 3}-L{sub 4}, Am(NO{sub 3}){sub 3}-HNO{sub 3}-L{sub 3}, and Am(NO{sub 3}){sub 3}-(HNO{sub 3}){sub 2}-L{sub 2}. However, some deviations occur at higher nitric acid concentrations. These deviations may be explained by the simplified but questionable assumption of constant activity coefficients in the organic phase. (author)

  5. Pre-Preliminary results from the phase III of the IAEA CRP: optimizing of reactor pressure vessel surveillance programmes and their analysis

    Energy Technology Data Exchange (ETDEWEB)

    Brumovsky, M; Gillemot, F; Kryukov, A; Levit, V

    1994-12-31

    This paper gives preliminary results and some conclusions from Phase III of the IAEA Coordinated Research Programme on ``Optimizing the Reactor Pressure Vessel Surveillance Programmes and their Analyses`` carried out during the last seven years in 15 member states. First analysis concerned: comparison of results from initial, un-irradiated materials condition, comparison of transition temperature shifts (from notch toughness testing) with respect to content of residual (P, Cu) and alloying (Ni) elements, type of material (base and weld metal), irradiation temperature (288 and 265 C), and type of fluence dependence. Special effort has been taken to the analysis of the behaviour of a chosen reference steel. (JRQ). 6 figs., 4 tabs.

  6. Simulated Target Preparation and Separation of Cd (II) - In (III) Matrices Using 8-Hydroxyquinoline Reagent for Producing Indium - III Radioisotope

    International Nuclear Information System (INIS)

    Sunarhadijoso Soenarjo; Swasono R Tamat; Lukiyawati; Lintang Maharani

    2002-01-01

    The potency of production and application of 111 In in Indonesia is not supported yet by capability in required processing technology. The presented paper is a preliminary study on processing technology of 111 In production from 112 Cd target covering simulated target preparation and separation of Cd(II)-In(III) matrices. The target preparation was performed by means of electroplating of CdSO 4 solution prepared from reaction of CdO and sulphuric acid. The separation of Cd(II)-In(III) matrices was proceeded by means of solvent extraction in the presence of 8-hydroxyquinoline as In(III)-complexing agent. The Cd-electroplating deposit was satisfactorily found by using 40-60 mA currents with an electroplating time of 5-7 hours. Simulated matrix solution containing mixture of Cd(II) and In(III) was extracted into chloroform with the presence of 8-hydroxyquinoline. The chloroform phase being assumed to contain In(III)-8-hydroxyquinoline complex was then re-extracted with 1 M HCl or saline solution. Each extraction fraction was spectrophotometrically identified in the region of 200-400 nm. From the resulting absorption spectra, it can be shown that the In(III) species is selectively separated from the Cd(II)-matrix. The use of saline in the re-extraction process is better then 1 M HCl solution due to solubility of 8-hydroxyquinoline in HCl. (author)

  7. New active analogues of Cucurbita maxima trypsin inhibitor III (CMTI-III) modified in the non-contact region.

    Science.gov (United States)

    Rózycki, J; Kupryszewski, G; Rolka, K; Ragnarsson, U; Zbyryt, T; Krokoszyńska, I; Wilusz, T

    1994-01-01

    Four new analogues of trypsin inhibitor CMTI-III(3-28) = [desArg1,desVal2,desGly29]CMTI-III which was recently shown to be fully active, were synthesized by the solid-phase method. The introduction of glycine in position 9 (peptide 1) and Gly-Pro-Gly (peptide 2) and Gly-Pro-Asn (peptide 3) in the regions 17-19 and 23-25, respectively, did not change the antitrypsin activity of all modified peptides. All of these substitutions are presumed to be outside the trypsin-binding loop as judged from the X-ray structure of the complex between beta-trypsin and the related inhibitor CMTI-I. Also the fourth analogue which was substituted in all the positions mentioned, exhibited the full activity.

  8. Antisense oligonucleotide inhibition of apolipoprotein C-III reduces plasma triglycerides in rodents, nonhuman primates, and humans.

    Science.gov (United States)

    Graham, Mark J; Lee, Richard G; Bell, Thomas A; Fu, Wuxia; Mullick, Adam E; Alexander, Veronica J; Singleton, Walter; Viney, Nick; Geary, Richard; Su, John; Baker, Brenda F; Burkey, Jennifer; Crooke, Stanley T; Crooke, Rosanne M

    2013-05-24

    Elevated plasma triglyceride levels have been recognized as a risk factor for the development of coronary heart disease. Apolipoprotein C-III (apoC-III) represents both an independent risk factor and a key regulatory factor of plasma triglyceride concentrations. Furthermore, elevated apoC-III levels have been associated with metabolic syndrome and type 2 diabetes mellitus. To date, no selective apoC-III therapeutic agent has been evaluated in the clinic. To test the hypothesis that selective inhibition of apoC-III with antisense drugs in preclinical models and in healthy volunteers would reduce plasma apoC-III and triglyceride levels. Rodent- and human-specific second-generation antisense oligonucleotides were identified and evaluated in preclinical models, including rats, mice, human apoC-III transgenic mice, and nonhuman primates. We demonstrated the selective reduction of both apoC-III and triglyceride in all preclinical pharmacological evaluations. We also showed that inhibition of apoC-III was well tolerated and not associated with increased liver triglyceride deposition or hepatotoxicity. A double-blind, placebo-controlled, phase I clinical study was performed in healthy subjects. Administration of the human apoC-III antisense drug resulted in dose-dependent reductions in plasma apoC-III, concomitant lowering of triglyceride levels, and produced no clinically meaningful signals in the safety evaluations. Antisense inhibition of apoC-III in preclinical models and in a phase I clinical trial with healthy subjects produced potent, selective reductions in plasma apoC-III and triglyceride, 2 known risk factors for cardiovascular disease. This compelling pharmacological profile supports further clinical investigations in hypertriglyceridemic subjects.

  9. Facilitating the implementation of the American College of Surgeons/Association of Program Directors in Surgery phase III skills curriculum: training faculty in the assessment of team skills.

    Science.gov (United States)

    Hull, Louise; Arora, Sonal; Stefanidis, Dimitrios; Sevdalis, Nick

    2015-11-01

    Effective teamwork is critical to safety in the operating room; however, implementation of phase III of the American College of Surgeons (ACS) and Association of Program Directors in Surgery (APDS) Curriculum that focuses on team-based skills remains worryingly low. Training and assessing the complexities of teamwork is challenging. The objective of this study was to establish guidelines and recommendations for training faculty in assessing/debriefing team skills. A multistage survey-based consensus study was completed by 108 experts responsible for training and assessing surgical residents from the ACS Accredited Educational Institutes. Experts agreed that a program to teach faculty to assess team-based skills should include training in the recognition of teamwork skills, practice rating these skills, and training in the provision of feedback/debriefing. Agreement was reached that faculty responsible for conducting team-based skills assessment should be revalidated every 2 years and stringent proficiency criteria should be met. Faculty development is critical to ensure high-quality, standardized training and assessment. Training faculty to assess team-based skills has the potential to facilitate the effective implementation of phase III of the ACS and APDS Curriculum. Copyright © 2015 Elsevier Inc. All rights reserved.

  10. Phase I/II Study Evaluating Early Tolerance in Breast Cancer Patients Undergoing Accelerated Partial Breast Irradiation Treated With the MammoSite Balloon Breast Brachytherapy Catheter Using a 2-Day Dose Schedule

    International Nuclear Information System (INIS)

    Wallace, Michelle; Martinez, Alvaro; Mitchell, Christina; Chen, Peter Y.; Ghilezan, Mihai; Benitez, Pamela; Brown, Eric; Vicini, Frank

    2010-01-01

    Purpose: Initial Phase I/II results using balloon brachytherapy to deliver accelerated partial breast irradiation (APBI) in 2 days in patients with early-stage breast cancer are presented. Materials and Methods: Between March 2004 and August 2007, 45 patients received adjuvant radiation therapy after lumpectomy with balloon brachytherapy in a Phase I/II trial delivering 2800 cGy in four fractions of 700 cGy. Toxicities were evaluated using the National Cancer Institute Common Toxicity Criteria for Adverse Events v3.0 scale and cosmesis was documented at ≥6 months. Results: The median age was 66 years (range, 48-83) and median skin spacing was 12 mm (range, 8-24). The median follow-up was 11.4 months (5.4-48 months) with 21 patients (47%) followed ≥1 year, 11 (24%) ≥2 years, and 7 (16%) ≥3 years. At <6 months (n = 45), Grade II toxicity rates were 9% radiation dermatitis, 13% breast pain, 2% edema, and 2% hyperpigmentation. Grade III breast pain was reported in 13% (n = 6). At ≥6 months (n = 43), Grade II toxicity rates were: 2% radiation dermatitis, 2% induration, and 2% hypopigmentation. Grade III breast pain was reported in 2%. Infection was 13% (n = 6) at <6 months and 5% (n = 2) at ≥6 months. Persistent seroma ≥6 months was 30% (n = 13). Fat necrosis developed in 4 cases (2 symptomatic). Rib fractures were seen in 4% (n = 2). Cosmesis was good/excellent in 96% of cases. Conclusions: Treatment with balloon brachytherapy using a 2-day dose schedule resulted acceptable rates of Grade II/III chronic toxicity rates and similar cosmetic results observed with a standard 5-day accelerated partial breast irradiation schedule.

  11. RECOVERY OF COPPER(II) AND CHROMIUM(III) FROM NITRATE ...

    African Journals Online (AJOL)

    Guerdouh A and Barkat D

    2016-05-01

    May 1, 2016 ... The ionic strength of the aqueous medium was ... phases were separated completely, concentrations of the copper(II) and chromium(III) ..... [18] Huff M M, Otu E O. Solvent Extraction and Ion Exchange, 2004, 22(4), 695-712.

  12. Preliminary evaluation of factors associated with premature trial closure and feasibility of accrual benchmarks in phase III oncology trials.

    Science.gov (United States)

    Schroen, Anneke T; Petroni, Gina R; Wang, Hongkun; Gray, Robert; Wang, Xiaofei F; Cronin, Walter; Sargent, Daniel J; Benedetti, Jacqueline; Wickerham, Donald L; Djulbegovic, Benjamin; Slingluff, Craig L

    2010-08-01

    A major challenge for randomized phase III oncology trials is the frequent low rates of patient enrollment, resulting in high rates of premature closure due to insufficient accrual. We conducted a pilot study to determine the extent of trial closure due to poor accrual, feasibility of identifying trial factors associated with sufficient accrual, impact of redesign strategies on trial accrual, and accrual benchmarks designating high failure risk in the clinical trials cooperative group (CTCG) setting. A subset of phase III trials opened by five CTCGs between August 1991 and March 2004 was evaluated. Design elements, experimental agents, redesign strategies, and pretrial accrual assessment supporting accrual predictions were abstracted from CTCG documents. Percent actual/predicted accrual rate averaged per month was calculated. Trials were categorized as having sufficient or insufficient accrual based on reason for trial termination. Analyses included univariate and bivariate summaries to identify potential trial factors associated with accrual sufficiency. Among 40 trials from one CTCG, 21 (52.5%) trials closed due to insufficient accrual. In 82 trials from five CTCGs, therapeutic trials accrued sufficiently more often than nontherapeutic trials (59% vs 27%, p = 0.05). Trials including pretrial accrual assessment more often achieved sufficient accrual than those without (67% vs 47%, p = 0.08). Fewer exclusion criteria, shorter consent forms, other CTCG participation, and trial design simplicity were not associated with achieving sufficient accrual. Trials accruing at a rate much lower than predicted (accrual rate) were consistently closed due to insufficient accrual. This trial subset under-represents certain experimental modalities. Data sources do not allow accounting for all factors potentially related to accrual success. Trial closure due to insufficient accrual is common. Certain trial design factors appear associated with attaining sufficient accrual. Defining

  13. Speciation of As(III) and As(V) in water and sediment using reverse-phase ion-pair high-performance liquid chromatography-neutron activation analysis (HPLC-NAA).

    Science.gov (United States)

    Tulasi, Delali; Adotey, Dennis; Affum, Andrews; Carboo, Derick; Serfor-Armah, Yaw

    2013-10-01

    Total As content and the As species distribution in water and sediments from the Kwabrafo stream, a major water body draining the Obuasi gold mining community in southwestern Ghana, have been investigated. Total As content was determined by instrumental neutron activation analysis (INAA). Ion-pair reverse phase high-performance liquid chromatography-neutron activation analysis (HPLC-NAA) was used for speciation of As species. Solid phase extraction with phosphate buffer was used to extract soluble As species from lyophilized sediment. The mass balance after phosphate extraction of soluble As species in sediment varied from 89 to 96 %. Compositionally appropriate reference material International Atomic Energy Agency (IAEA)-Lake Sediment (SL)-1 was used to check the validity of INAA method for total As determination. The measured values are in good agreement with the IAEA recommended value and also within the 95 % confidence interval. The accuracy of the measurement in terms of relative deviation from the IAEA recommended value was ±0.83 %. "In-house" prepared As(III) and As(V) standards were used to validate the HPLC-INAA method used for the As species determination. Total As concentration in the water samples ranged from 1.15 to 9.20 mg/L. As(III) species in water varied from 0.13 to 0.7 mg/L, while As(V) species varied from 0.79 to 3.85 mg/L. Total As content in sediment ranged from 2,134 to 3,596 mg/kg dry mass. The levels of As(III) and As(V) species in the sediment ranges from 138 to 506 mg/kg dry mass and 156 to 385 mg/kg dry mass, respectively.

  14. Phase 1 and 2 feasibility study report for the 300-FF-1 Operable Unit

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    The 300-FF-1 Operable Unit (OU) feasibility study (FS) presented in this document completes the FS process only through the first two study phases: Phase I, Remedial Alternatives Development, and Phase II, Remedial Alternatives Screening in accordance with CERCIA guidance for performing Remedial Investigations and Feasibility Studies (RI/FS) (EPA 1988a). This Phase I/II study provides a generalized view of workable remedial technologies as applied to the site contamination problems as a whole. Phase III, Detailed Analysis of Alternatives, will be performed at a later date to further evaluate screened alternatives based on the nine criteria in the CERCLA RI/FS guidance. The purpose of this Phase I/II FS is to develop and screen a range of alternatives for remediation of contamination present in the vadose zone of the 300-FF-1 OU. The scope of work for this Phase I/II FS includes five primary tasks: 1. Review existing documents and their associated data from relevant investigations and studies; 2. Establish remedial action objectives (RAO) and general response actions (GRA); 3. Identify applicable or relevant and appropriate requirements (ARARS) pertinent to all general response actions (including waste disposal); 4. Develop remedial alternatives (Phase I) applicable to the 300-FF-1 OU including identification and screening of technologies and process options, and assembly of remedial alternatives from representative technology types; 5. Screen alternatives (Phase II) developed in Phase I for implementability, effectiveness, and cost to identify those alternatives which warrant advancement to the detailed analysis phase (Phase III) of the FS.

  15. Column Chromatography Of Co(II), Zn(II) And Eu(III) Using Pistachio Shell And Different Mobile Phases

    International Nuclear Information System (INIS)

    Abdel-Fattah, A.A.

    2009-01-01

    Pistachio shell particles (0.5-1 mm) have been applied as the stationary phase for studying the column chromatography of Co(II), Zn(II) and Eu(III) at room temperature; 26 + - 1 oC. This solid sorbent has been characterized by thermogravimetric analysis, infra-red spectroscopy and X-ray diffraction. Its surface area and percent of swelling have been also determined. Different eluting agents have been used for eluting the sorbed elements. The elution curves have been done from which the distribution coefficients (K d ), number of theoretical plates (N) and heights equivalent to theoretical plates (H) have been determined. Column performance studies have been conducted for a representative system under certain experimented conditions and Van Deemter equation has been applied. Thermodynamic studies have been applied and thermodynamic functions ( δG 0 ,δH 0 andδ S 0 ) have been calculated for this representative system by determining K d at three different room temperatures (18, 26 and 37 + - 1o C).

  16. Acoustic Detection of Faults and Degradation in a High-Bypass Turbofan Engine during VIPR Phase III Testing

    Science.gov (United States)

    Boyle, Devin K.

    2017-01-01

    The Vehicle Integrated Propulsion Research (VIPR) Phase III project was executed at Edwards Air Force Base, California, by the National Aeronautics and Space Administration and several industry, academic, and government partners in the summer of 2015. One of the research objectives was to use external radial acoustic microphone arrays to detect changes in the noise characteristics produced by the research engine during volcanic ash ingestion and seeded fault insertion scenarios involving bleed air valves. Preliminary results indicate the successful acoustic detection of suspected degradation as a result of cumulative exposure to volcanic ash. This detection is shown through progressive changes, particularly in the high-frequency content, as a function of exposure to greater cumulative quantities of ash. Additionally, detection of the simulated failure of the 14th stage stability bleed valve and, to a lesser extent, the station 2.5 stability bleed valve, to their fully-open fail-safe positions was achieved by means of spectral comparisons between nominal (normal valve operation) and seeded fault scenarios.

  17. Early orthopedic correction of skeletal Class III malocclusion using combined reverse twin block and face mask therapy

    Directory of Open Access Journals (Sweden)

    Vinay Kumar Chugh

    2015-01-01

    Full Text Available A 6-year 8-month-old girl presented with a moderate Class III malocclusion characterized by mid-face deficiency and an anterior cross bite. In the first phase, the patient was treated with combination of reverse twin block and facemask therapy. In phase two, fixed appliances were placed in the permanent dentition. The post treatment results were good and a favorable growth tendency could be observed. The correction of the Class III malocclusion occurred by a combination of skeletal and dental improvements. This report shows successful correction of skeletal Class III malocclusion in the early transitional dentition using combination therapy.

  18. Impact of Fe(III)-OM complexes and Fe(III) polymerization on SOM pools reactivity under different land uses

    Science.gov (United States)

    Giannetta, B.; Plaza, C.; Zaccone, C.; Siebecker, M. G.; Rovira, P.; Vischetti, C.; Sparks, D. L.

    2017-12-01

    Soil organic matter (SOM) protection and long-term accumulation are controlled by adsorption to mineral surfaces in different ways, depending on its molecular structure and pedo-climatic conditions. Iron (Fe) oxides are known to be key regulators of the soil carbon (C) cycle, and Fe speciation in soils is highly dependent on environmental conditions and chemical interactions with SOM. However, the molecular structure and hydrolysis of Fe species formed in association with SOM is still poorly described. We hypothesize the existence of two pools of Fe which interact with SOM: mononuclear Fe(III)-SOM complexes and precipitated Fe(III) hydroxides. To verify our hypothesis, we investigated the interactions between Fe(III) and physically isolated soil fractions by means of batch experiments at pH 7. Specifically, we examined the fine silt plus clay (FSi+C) fraction, obtained by ultrasonic dispersion and wet sieving. The soil samples spanned several land uses, including coniferous forest (CFS), grassland (GS), technosols (TS) and agricultural (AS) soils. Solid phase products and supernatants were analyzed for C and Fe content. X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) analysis were also performed. Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) was used to assess the main C functional groups involved in C complexation and desorption experiments. Preliminary linear combination fitting (LCF) of Fe K-edge extended X-ray absorption fine structure (EXAFS) spectra suggested the formation of ferrihydrite-like polymeric Fe(III) oxides in reacted CFS and GS samples, with higher C and Fe concentration. Conversely, mononuclear Fe(III) OM complexes dominated the speciation for TS and AS samples, characterized by lower C and Fe concentration, inhibiting the hydrolysis and polymerization of Fe (III). This approach will help revealing the mechanisms by which SOM pools can control Fe(III) speciation, and will elucidate how both Fe(III

  19. Tier I ecological evaluation for phase III channel improvements to the John. F. Baldwin ship channel

    Energy Technology Data Exchange (ETDEWEB)

    Bienert, R.W.; Shreffler, D.K.; Word, J.Q.; Kohn, N.P. [Battelle/Marine Sciences Lab., Sequim, WA (United States)

    1994-05-01

    To assist the US Army Corps of Engineers (USACE) in determing whether the material from proposed dredging of the John F. Baldwin Ship Channel (JFBSC) is suitable for unrestricted, unconfined open-ocean disposal, Battelle/Marine Sciences Laboratory (MSL) prepared this report. Based on these findings, sediments that would be removed during Phase III improvements to the JFBSC fail to meet the three suitability criteria for open-ocean disposal. Firstly, fine-grained sediments comprise a significant fraction of the bottom material in some areas of the channel, and this material is not exposed to high current or wave energy. Dredged material from the JFBSC is not being proposed for beach nourishment; therefore the second criterion is not met. JFBSC sediments do not meet the third criterion because, although they may be substantially similar to substrates at several of the proposed disposal sites, they are from an area that historically has experienced loading of contaminants, which toxicology studies have shown have the potential to result in acute toxicity or significant bioaccumulation.

  20. Flow injection microfluidic device with on-line fluorescent derivatization for the determination of Cr(III) and Cr(VI) in water samples after solid phase extraction

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Guilong [Key Laboratory of Eco-Environment of Three Gorges Region of Ministry of Education, Chongqing University, Chongqing, 400045 (China); Department of Chemistry, Beijing Key Laboratory of Microanalytical Methods and Instrumentation, Tsinghua University, Beijing, 100084 (China); He, Qiang, E-mail: heqiang0980@163.com [Key Laboratory of Eco-Environment of Three Gorges Region of Ministry of Education, Chongqing University, Chongqing, 400045 (China); Lu, Ying [Department of Mathematics and Physics, Armed Police College, Chengdu, 610213 (China); Huang, Jing [Research Center for Advanced Computation, College of Science, Xihua University, Chengdu, 610039 (China); Lin, Jin-Ming, E-mail: jmlin@mail.tsinghua.edu.cn [Department of Chemistry, Beijing Key Laboratory of Microanalytical Methods and Instrumentation, Tsinghua University, Beijing, 100084 (China)

    2017-02-22

    In this paper, a rapid and simple method using magnetic multi-walled carbon nanotubes (MWCNTS), as a solid-phase extraction (SPE) sorbent, was successfully developed for extraction and preconcentration trace amounts of Cr(III) in water samples. The synthesized magnetic-MWCNTs nanocomposite was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). A rhodamine derivative (R1) was synthesized and characterized as a highly selective and sensitive fluorescent derivatizing agent for Cr(III). After SPE procedure, Cr(III) analysis was performed by flow injection microfluidic chip with on-line fluorescent derivatization and laser-induced fluorescence (LIF) spectroscopy detection. The parameters, which affected the efficiency of the developed method were investigated and optimized. Under the optimized conditions, the method exhibited a linear dynamic range of 0–10.0 nM, with a detection limit of 0.094 nM and an enrichment factor of 38. Furthermore, real water samples were analyzed and good recoveries were obtained from 91.0 to 101.6%. - Graphical abstract: Flow injection microfluidic device with on-line fluorescent derivatization and detection coupled to LIF. - Highlights: • A highly selective and sensitive derivatizing reagent for Cr(III) was synthesized and characterized. • The magnetic-MWCNTs nanocomposite as a SPE sorbent was successfully synthesized and characterized. • A new portable detection system was developed for microfluidic chip FIA platform.

  1. Separation of americium (III) and strontium (II) using TEHDGA and 18-crown-6

    Energy Technology Data Exchange (ETDEWEB)

    Sinharoy, Prithwish; Khan, Pasupati Nath; Nair, Deepika; Jagasia, Poonam; Dhami, P.S.; Kaushik, C.P.; Banerjee, Kalyan [Bhabha Atomic Research Centre, Mumbai (India). Nuclear Recycle Group; Anitha, M. [Bhabha Atomic Research Centre, Mumbai (India). Rare Earth Development Section; Sharma, J.N. [Bhabha Atomic Research Centre, Mumbai (India). Process Development Div.

    2017-06-01

    This work describes extraction of Am(III) and Sr(II) together with tetra(2-ethylhexyl) diglycolamide (TEHDGA) and selective back-extraction of strontium with a strontium complexant, 18-crown-6, leading to their separation from each other. 0.3 M TEHDGA+5% isodecyl alcohol/n-dodecane was used to extract Am(III) and Sr(II) from 4 M nitric acid into organic phase with very high D (D{sub Am}=1000, D{sub Sr}=22) and 0.1 M 18-crown-6 dissolved in 4 M nitric acid is used for selective stripping of Sr(II) from loaded extract phase. Am(III) left in the extract phase was then stripped with 0.01 M nitric acid. Stripping of Sr(II) was found to increase with increase in 18-crown-6 concentration, at 0.1 M 18-crown-6 dissolved in 4 M nitric acid, 83% of the loaded strontium (D{sub Sr}=0.20) was back-extracted in a single contact while loss of Am(III) was 0.8% (D{sub Am}=122.45). Stoichiometry limit of 1:1 was observed between strontium and 18-crown-6. Strontium was precipitated and separated from the complexant by Na{sub 2}SO{sub 4} or Na{sub 2}CO{sub 3}. This process was tested with simulated solution of high level waste and found suitable for quantitative recovery of strontium with high purity.

  2. Carbonato-bridged Ni(II)2Ln(III)2 (Ln(III) = Gd(III), Tb(III), Dy(III)) complexes generated by atmospheric CO2 fixation and their single-molecule-magnet behavior: [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(MeOH or H2O)Ln(III)(NO3)}2]·solvent [3-MeOsaltn = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato].

    Science.gov (United States)

    Sakamoto, Soichiro; Fujinami, Takeshi; Nishi, Koshiro; Matsumoto, Naohide; Mochida, Naotaka; Ishida, Takayuki; Sunatsuki, Yukinari; Re, Nazzareno

    2013-06-17

    Atmospheric CO2 fixation of [Ni(II)(3-MeOsaltn)(H2O)2]·2.5H2O [3-MeOsaltn = N,N'-bis(3-methoxy-2-oxybenzylidene)-1,3-propanediaminato], Ln(III)(NO3)3·6H2O, and triethylamine occurred in methanol/acetone, giving a first series of carbonato-bridged Ni(II)2Ln(III)2 complexes [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(MeOH)Ln(III)(NO3)}2] (1Gd, 1Tb, and 1Dy). When the reaction was carried out in acetonitrile/water, it gave a second series of complexes [(μ4-CO3)2{Ni(II)(3-MeOsaltn)(H2O)Ln(III)(NO3)}2]·2CH3CN·2H2O (2Gd, 2Tb, and 2Dy). For both series, each Ni(II)2Ln(III)2 structure can be described as two di-μ-phenoxo-bridged Ni(II)Ln(III) binuclear units bridged by two carbonato CO3(2-) units to form a carbonato-bridged (μ4-CO3)2{Ni(II)2Ln(III)2} structure. The high-spin Ni(II) ion has octahedral coordination geometry, and the Ln(III) ion is coordinated by O9 donor atoms from Ni(II)(3-MeOsaltn), bidentate NO3(-), and one and two oxygen atoms of two CO3(2-) ions. The NO3(-) ion for the first series roughly lie on Ln-O(methoxy) bonds and are tilted toward the outside, while for the second series, the two oxygen atoms roughly lie on one of the Ln-O(phenoxy) bonds due to the intramolecular hydrogen bond. The temperature-dependent magnetic susceptibilities indicated a ferromagnetic interaction between the Ni(II) and Ln(III) ions (Ln(III) = Gd(III), Tb(III), Dy(III)) for all of the complexes, with a distinctly different magnetic behavior between the two series in the lowest-temperature region due to the Ln(III)-Ln(III) magnetic interaction and/or different magnetic anisotropies of the Tb(III) or Dy(III) ion. Alternating-current susceptibility measurements under the 0 and 1000 Oe direct-current (dc) bias fields showed no magnetic relaxation for the Ni(II)2Gd(III)2 complexes but exhibited an out-of-phase signal for Ni(II)2Tb(III)2 and Ni(II)2Dy(III)2, indicative of slow relaxation of magnetization. The energy barriers, Δ/kB, for the spin flipping were estimated from the Arrhenius

  3. Surface decoration of amine-rich carbon nitride with iron nanoparticles for arsenite (As{sup III}) uptake: The evolution of the Fe-phases under ambient conditions

    Energy Technology Data Exchange (ETDEWEB)

    Georgiou, Y., E-mail: yiannisgeorgiou@hotmail.com [Physics Department, University of Ioannina, Ioannina 45110 (Greece); Mouzourakis, E., E-mail: emouzou@cc.uoi.gr [Physics Department, University of Ioannina, Ioannina 45110 (Greece); Bourlinos, A.B., E-mail: bourlino@cc.uoi.gr [Physics Department, University of Ioannina, Ioannina 45110 (Greece); Regional Centre of Advanced Technologies and Materials, Faculty of Science, Department of Physical Chemistry and Experimental Physics, Palacky University in Olomouc, 77146 (Czech Republic); Zboril, R., E-mail: radek.zboril@upol.cz [Regional Centre of Advanced Technologies and Materials, Faculty of Science, Department of Physical Chemistry and Experimental Physics, Palacky University in Olomouc, 77146 (Czech Republic); Karakassides, M.A., E-mail: mkarakas@cc.uoi.gr [Department of Materials Science and Engineering, University of Ioannina, Ioannina 45110 (Greece); Douvalis, A.P., E-mail: adouval@uoi.gr [Physics Department, University of Ioannina, Ioannina 45110 (Greece); Bakas, Th., E-mail: tbakas@cc.uoi.gr [Physics Department, University of Ioannina, Ioannina 45110 (Greece); Deligiannakis, Y., E-mail: ideligia@cc.uoi.gr [Physics Department, University of Ioannina, Ioannina 45110 (Greece)

    2016-07-15

    Highlights: • Novel hybrid based on carbon nitride and iron nanoparticles (gC{sub 3}N{sub 4}-rFe). • gC{sub 3}N{sub 4}-rFe superior As{sup III} sorbent(76.5 mg g{sup −1}). • Surface complexation modeling of As{sup III} adsorption. • Dual mode EPR,monitoring of Fe{sup 2+} and Fe{sup 3+} evolution. - Abstract: A novel hybrid material (gC{sub 3}N{sub 4}-rFe) consisting of amine-rich graphitic carbon nitride (gC{sub 3}N{sub 4}), decorated with reduced iron nanoparticles (rFe) is presented. XRD and TEM show that gC{sub 3}N{sub 4}-rFe bears aggregation-free Fe-nanoparticles (10 nm) uniformly dispersed over the gC{sub 3}N{sub 4} surface. In contrast, non-supported iron nanoparticles are strongly aggregated, with non-uniform size distribution (20–100 nm). {sup 57}Fe-Mössbauer spectroscopy, dual-mode electron paramagnetic resonance (EPR) and magnetization measurements, allow a detailed mapping of the evolution of the Fe-phases after exposure to ambient O{sub 2}. The as-prepared gC{sub 3}N{sub 4}-rFe bears Fe{sup 2+} and Fe° phases, however only after long exposure to ambient O{sub 2}, a Fe-oxide layer is formed around the Fe° core. In this [Fe°/Fe-oxide] core-shell configuration, the gC{sub 3}N{sub 4}-rFe hybrid shows enhanced As{sup III} uptake capacity of 76.5 mg g{sup −1}, i.e., ca 90% higher than the unmodified carbonaceous support, and 300% higher than the non-supported Fe-nanoparticles. gC{sub 3}N{sub 4}-rFe is a superior As{sup III} sorbent i.e., compared to its single counterparts or vs. graphite/graphite oxide or activated carbon analogues (11–36 mg g{sup −1}). The present results demonstrate that the gC{sub 3}N{sub 4} matrix is not simply a net that holds the particles, but rather an active component that determines particle formation dynamics and ultimately their redox profile, size and surface dispersion homogeneity.

  4. Virtual reality exercise on a home-based phase III cardiac rehabilitation program, effect on executive function, quality of life and depression, anxiety and stress: a randomized controlled trial.

    Science.gov (United States)

    Vieira, Ágata; Melo, Cristina; Machado, Jorge; Gabriel, Joaquim

    2018-02-01

    To analyse the effect of a six-month home-based phase III cardiac rehabilitation (CR) specific exercise program, performed in a virtual reality (Kinect) or conventional (booklet) environment, on executive function, quality of life and depression, anxiety and stress of subjects with coronary artery disease. A randomized controlled trial was conducted with subjects, who had completed phase II, randomly assigned to intervention group 1 (IG1), whose program encompassed the use of Kinect (n = 11); or intervention group 2 (IG2), a paper booklet (n = 11); or a control group (CG), only subjected to the usual care (n = 11). The three groups received education on cardiovascular risk factors. The assessed parameters, at baseline (M0), 3 (M1) and 6 months (M2), were executive function, control and integration in the implementation of an adequate behaviour in relation to a certain objective, specifically the ability to switch information (Trail Making Test), working memory (Verbal Digit Span test), and selective attention and conflict resolution ability (Stroop test), quality of life (MacNew questionnaire) and depression, anxiety and stress (Depression, Anxiety and Stress Scale 21). Descriptive and inferential statistical measures were used, significance level was set at .05. The IG1 revealed significant improvements, in the selective attention and conflict resolution ability, in comparison with the CG in the variable difference M0 - M2 (p = .021) and in comparison with the IG2 in the variable difference M1 - M2 and M0 - M2 (p = .001 and p = .002, respectively). No significant differences were found in the quality of life, and depression, anxiety and stress. The virtual reality format had improved selective attention and conflict resolution ability, revealing the potential of CR, specifically with virtual reality exercise, on executive function. Implications for Rehabilitation In cardiac rehabilitation, especially in phase III, it is

  5. On the growth of ammonium nitrate(III) crystals

    NARCIS (Netherlands)

    Vogels, L.J.P.; Marsman, H.A.M.; Verheijen, M.A.; Bennema, P.; Elwenspoek, Michael Curt

    The growth rate of NH4NO3 phase III crystals is measured and interpreted using two models. The first is a standard crystal growth model based on a spiral growth mechanism, the second outlines the concept of kinetical roughening. As the crystal becomes rough a critical supersaturation can be

  6. Sparkle/PM3 for the modeling of europium(III), gadolinium(III), and terbium(III) complexes

    International Nuclear Information System (INIS)

    Freire, Ricardo O.; Rocha, Gerd B.; Simas, Alfredo M.

    2009-01-01

    The Sparkle/PM3 model is extended to europium(III), gadolinium(III), and terbium(III) complexes. The validation procedure was carried out using only high quality crystallographic structures, for a total of ninety-six Eu(III) complexes, seventy Gd(III) complexes, and forty-two Tb(III) complexes. The Sparkle/PM3 unsigned mean error, for all interatomic distances between the trivalent lanthanide ion and the ligand atoms of the first sphere of coordination, is: 0.080 A for Eu(III); 0.063 A for Gd(III); and 0.070 A for Tb(III). These figures are similar to the Sparkle/AM1 ones of 0.082 A, 0.061 A, and 0.068 A respectively, indicating they are all comparable parameterizations. Moreover, their accuracy is similar to what can be obtained by present-day ab initio effective core potential full geometry optimization calculations on such lanthanide complexes. Finally, we report a preliminary attempt to show that Sparkle/PM3 geometry predictions are reliable. For one of the Eu(III) complexes, BAFZEO, we created hundreds of different input geometries by randomly varying the distances and angles of the ligands to the central Eu(III) ion, which were all subsequently fully optimized. A significant trend was unveiled, indicating that more accurate local minima geometries cluster at lower total energies, thus reinforcing the validity of sparkle model calculations. (author)

  7. Reversed phase chromatographic behaviour of Pu (III), Pu (IV) and Pu (VI) in presence of α-hydroxyisobutyric acid

    International Nuclear Information System (INIS)

    Jaison, P.G.; Telmore, V.M.; Kumar, Pranaw

    2016-01-01

    Understanding the aqueous chemistry of plutonium is important in process conditions as well as in environmental conditions. Since plutonium possesses multiple oxidation states which can coexist in solution, a reliable method for the identification of these oxidation states is essential to understand its physical and chemical processes. The identification of plutonium oxidation states is conventionally determined through a series of liquid-liquid extraction procedures using selective extractants. Spectroscopic and laser based techniques also have been used for the identification of its oxidation state in solutions. Liquid chromatographic behavior of different oxidation states of Pu and other actinide ions is reported to correlate their retention behaviour with stability constants. Objective of the present work is to study the reversed phase chromatography behavior of the three oxidation states of plutonium viz. Pu(III), Pu(IV) and Pu(VI) in presence of á-hydroxyisobutyric acid (HIBA) as an eluent

  8. A phase I/II clinical trial for the hybrid of intracavitary and interstitial brachytherapy for locally advanced cervical cancer.

    Science.gov (United States)

    Murakami, Naoya; Kato, Shingo; Nakano, Takashi; Uno, Takashi; Yamanaka, Takeharu; Sakurai, Hideyuki; Yoshimura, Ryoichi; Hiratsuka, Junichi; Kuroda, Yuki; Yoshio, Kotaro; Itami, Jun

    2016-08-17

    This paper describes about a study protocol of phase I/II multicenter prospective clinical trial evaluating the feasibility and efficacy of the hybrid of intracavitary and interstitial brachytherapy (HBT) for locally advanced uterine cervical cancer patients. Patients with histologically confirmed FIGO stage IB2, IIA2, IIB, and IIIB uterine cervical carcinoma width of which is larger than 5 cm assessed by MRI will be entered to this clinical trial. Protocol therapy is 30-30.6 Gy in 15-17 fractions of whole pelvic radiotherapy concurrent with weekly CDDP (40 mg/m(2)), followed by 24 Gy in 4 fractions of HBT and central shield EBRT up to 50-50.4 Gy in 25-28 fractions. Tumor width is assessed again within one week before the first HBT and if the tumor width is larger than 4 cm, patients proceed to the secondary registration. In phase I section, feasibility of this will be investigated. If less than 10 % out of 20 patients experienced greater than grade 3 acute non-hematologic adverse effects, the study proceeds to phase II part. In phase II part a total of 55 patients will be accrued and the efficacy of the HBT will be investigated comparing with historical control data. If the lower margin of 90 % confidence interval of the 2-year pelvic progression-free survival of the HBT trial is higher than 64 %, the HBT is considered to be more effective than conventional ICBT. The aim of this study is to demonstrate the feasibility and efficacy of the HBT for locally advanced cervical cancer. This trial will clarify the indication, feasibility, and efficacy of this new technique. UMIN000019081 ; Registration date: 2015/9/30.

  9. The Value of Botox-A in Acute Radiation Proctitis: Results From a Phase I/II Study Using a Three-Dimensional Scoring System

    International Nuclear Information System (INIS)

    Vuong, Te; Waschke, Kevin; Niazi, Tamim; Richard, Carole; Parent, Josee; Liberman, Sender; Mayrand, Serge; Loungnarath, Rasmy; Stein, Barry; Devic, Slobodan

    2011-01-01

    Purpose: Acute radiation proctitis (ARP) is a common side effect of pelvic radiotherapy, and its management is challenging in daily practice. The present phase I/II study evaluates the safety and efficacy of the botulinum toxin A (BTX-A) in ARP treatment for rectal cancer patients undergoing neoadjuvant high-dose-rate endorectal brachytherapy (HDREBT). Methods and Materials: Fifteen patients, treated with neoadjuvant HDREBT, 26-Gy in 4 fractions, received the study treatment that consisted of a single injection of BTX-A into the rectal wall. The injection was performed post-HDREBT and prior to the development of ARP. The control group, 20 such patients, did not receive the BTX-A injection. Both groups had access to standard treatment with hydrocortisone rectal aerosol foam (Cortifoam) and anti-inflammatory and narcotic medication. The ARP was clinically evaluated by self-administered daily questionnaires using visual analog scores to document frequency and urgency of bowel movements, rectal burning/tenesmus, and pain symptoms before and after HDREBT. Results: At the time of this analysis, there was no observed systemic toxicity. Patient compliance with the self-administered questionnaire was 100% from week 1 to 4, 70% during week 5, and 40% during week 6. The maximum tolerated dose was established at the 100-U dose level, and noticeable mean differences were observed in bowel frequency (p = 0.016), urgency (p = 0.007), and pain (p = 0.078). Conclusions: This study confirms the feasibility and efficacy of BTX-A intervention at 100-U dose level for study patients compared to control patients. A phase III study with this dose level is planned to validate these results.

  10. Expression profiling of blood samples from an SU5416 Phase III metastatic colorectal cancer clinical trial: a novel strategy for biomarker identification

    International Nuclear Information System (INIS)

    DePrimo, Samuel E; Wong, Lily M; Khatry, Deepak B; Nicholas, Susan L; Manning, William C; Smolich, Beverly D; O'Farrell, Anne-Marie; Cherrington, Julie M

    2003-01-01

    Microarray-based gene expression profiling is a powerful approach for the identification of molecular biomarkers of disease, particularly in human cancers. Utility of this approach to measure responses to therapy is less well established, in part due to challenges in obtaining serial biopsies. Identification of suitable surrogate tissues will help minimize limitations imposed by those challenges. This study describes an approach used to identify gene expression changes that might serve as surrogate biomarkers of drug activity. Expression profiling using microarrays was applied to peripheral blood mononuclear cell (PBMC) samples obtained from patients with advanced colorectal cancer participating in a Phase III clinical trial. The PBMC samples were harvested pre-treatment and at the end of the first 6-week cycle from patients receiving standard of care chemotherapy or standard of care plus SU5416, a vascular endothelial growth factor (VEGF) receptor tyrosine kinase (RTK) inhibitor. Results from matched pairs of PBMC samples from 23 patients were queried for expression changes that consistently correlated with SU5416 administration. Thirteen transcripts met this selection criterion; six were further tested by quantitative RT-PCR analysis of 62 additional samples from this trial and a second SU5416 Phase III trial of similar design. This method confirmed four of these transcripts (CD24, lactoferrin, lipocalin 2, and MMP-9) as potential biomarkers of drug treatment. Discriminant analysis showed that expression profiles of these 4 transcripts could be used to classify patients by treatment arm in a predictive fashion. These results establish a foundation for the further exploration of peripheral blood cells as a surrogate system for biomarker analyses in clinical oncology studies

  11. Development of standardized laboratory methods and quality processes for a phase III study of the RTS, S/AS01 candidate malaria vaccine

    Directory of Open Access Journals (Sweden)

    Carter Terrell

    2011-08-01

    Full Text Available Abstract Background A pivotal phase III study of the RTS,S/AS01 malaria candidate vaccine is ongoing in several research centres across Africa. The development and establishment of quality systems was a requirement for trial conduct to meet international regulatory standards, as well as providing an important capacity strengthening opportunity for study centres. Methods Standardized laboratory methods and quality assurance processes were implemented at each of the study centres, facilitated by funding partners. Results A robust protocol for determination of parasite density based on actual blood cell counts was set up in accordance with World Health Organization recommendations. Automated equipment including haematology and biochemistry analyzers were put in place with standard methods for bedside testing of glycaemia, base excess and lactacidaemia. Facilities for X-rays and basic microbiology testing were also provided or upgraded alongside health care infrastructure in some centres. External quality assurance assessment of all major laboratory methods was established and method qualification by each laboratory demonstrated. The resulting capacity strengthening has ensured laboratory evaluations are conducted locally to the high standards required in clinical trials. Conclusion Major efforts by study centres, together with support from collaborating parties, have allowed standardized methods and robust quality assurance processes to be put in place for the phase III evaluation of the RTS, S/AS01 malaria candidate vaccine. Extensive training programmes, coupled with continuous commitment from research centre staff, have been the key elements behind the successful implementation of quality processes. It is expected these activities will culminate in healthcare benefits for the subjects and communities participating in these trials. Trial registration Clinicaltrials.gov NCT00866619

  12. Expression profiling of blood samples from an SU5416 Phase III metastatic colorectal cancer clinical trial: a novel strategy for biomarker identification

    Directory of Open Access Journals (Sweden)

    Smolich Beverly D

    2003-02-01

    Full Text Available Abstract Background Microarray-based gene expression profiling is a powerful approach for the identification of molecular biomarkers of disease, particularly in human cancers. Utility of this approach to measure responses to therapy is less well established, in part due to challenges in obtaining serial biopsies. Identification of suitable surrogate tissues will help minimize limitations imposed by those challenges. This study describes an approach used to identify gene expression changes that might serve as surrogate biomarkers of drug activity. Methods Expression profiling using microarrays was applied to peripheral blood mononuclear cell (PBMC samples obtained from patients with advanced colorectal cancer participating in a Phase III clinical trial. The PBMC samples were harvested pre-treatment and at the end of the first 6-week cycle from patients receiving standard of care chemotherapy or standard of care plus SU5416, a vascular endothelial growth factor (VEGF receptor tyrosine kinase (RTK inhibitor. Results from matched pairs of PBMC samples from 23 patients were queried for expression changes that consistently correlated with SU5416 administration. Results Thirteen transcripts met this selection criterion; six were further tested by quantitative RT-PCR analysis of 62 additional samples from this trial and a second SU5416 Phase III trial of similar design. This method confirmed four of these transcripts (CD24, lactoferrin, lipocalin 2, and MMP-9 as potential biomarkers of drug treatment. Discriminant analysis showed that expression profiles of these 4 transcripts could be used to classify patients by treatment arm in a predictive fashion. Conclusions These results establish a foundation for the further exploration of peripheral blood cells as a surrogate system for biomarker analyses in clinical oncology studies.

  13. Phasing-in Basel III capital and liquidity requirements in post-revolution Egypt

    Directory of Open Access Journals (Sweden)

    Monal Abdel-Baki

    2012-08-01

    Full Text Available The Basel Committee has introduced a new set of capital and liquidity requirements to be introduced by the global banking system during 2013 till January 2019. Egypt possesses a well-capitalised banking sector, yet it has been exposed to the devastating shock imposed by its popular revolution. Using the GMM method, the impact of introducing the new capital and liquidity requirements on the macroeconomic performance of the Egyptian economy is examined. The results reveal that Egyptian banks are motivated to enhance capital and liquidity ratios in the case of realizing high profits and favourable conditions at the individual banking level. On the other hand, negative macroeconomic performance and a poor business environment substantially deter the preparedness of Egyptian banks to meet the Basel III requirements. The analysis is timely given the need for compliance with Basel III as one of the requirements to raise the credit rating of the devastated economy.

  14. Ferrous Iron Oxidation under Varying pO2 Levels: The Effect of Fe(III)/Al(III) Oxide Minerals and Organic Matter.

    Science.gov (United States)

    Chen, Chunmei; Thompson, Aaron

    2018-01-16

    Abiotic Fe(II) oxidation by O 2 commonly occurs in the presence of mineral sorbents and organic matter (OM) in soils and sediments; however, this tertiary system has rarely been studied. Therefore, we examined the impacts of mineral surfaces (goethite and γ-Al 2 O 3 ) and organic matter [Suwannee River fulvic acid (SRFA)] on Fe(II) oxidation rates and the resulting Fe(III) (oxyhydr)oxides under 21 and 1% pO 2 at pH 6. We tracked Fe dynamics by adding 57 Fe(II) to 56 Fe-labeled goethite and γ-Al 2 O 3 and characterized the resulting solids using 57 Fe Mössbauer spectroscopy. We found Fe(II) oxidation was slower at low pO 2 and resulted in higher-crystallinity Fe(III) phases. Relative to oxidation of Fe(II) (aq) alone, both goethite and γ-Al 2 O 3 surfaces increased Fe(II) oxidation rates regardless of pO 2 levels, with goethite being the stronger catalyst. Goethite surfaces promoted the formation of crystalline goethite, while γ-Al 2 O 3 favored nano/small particle or disordered goethite and some lepidocrocite; oxidation of Fe(II) aq alone favored lepidocrocite. SRFA reduced oxidation rates in all treatments except the mineral-free systems at 21% pO 2 , and SRFA decreased Fe(III) phase crystallinity, facilitating low-crystalline ferrihydrite in the absence of mineral sorbents, low-crystalline lepidocrocite in the presence of γ-Al 2 O 3 , but either crystalline goethite or ferrihydrite when goethite was present. This work highlights that the oxidation rate, the types of mineral surfaces, and OM control Fe(III) precipitate composition.

  15. Interactions of Eu(III) with biogenic CaCO{sub 3} studied with TRLFS

    Energy Technology Data Exchange (ETDEWEB)

    Johnstone, Erik V.; Schmidt, Moritz [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Surface Processes; Cherkouk, Andrea [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Biogeochemistry

    2016-07-01

    The interactions of Eu(III) with CaCO{sub 3} arising from biogenic origin was investigated by Time-Resolved Laser-Induced Fluorescence Spectroscopy (TRLFS). Biologically-induced precipitation via ureolysis was studied with the bacteria Sporosarcina pasteurii in the presence of Eu(III). Biomineralization occurred forming mixed phases of vaterite and calcite after one day that transformed over two weeks to pure calcite. Eu(III) was quantitatively removed from solution during mineral formation. TRLFS results show that after one day the Eu{sup 3+} is located in the vaterite phase. After one week, the Eu{sup 3+} was found primarily in the vaterite, despite calcite now being the predominant mineral, and a transition species was also formed. In the calcite two incorporated Eu{sup 3+} species were present: one substitutes at the Ca{sup 2+} site in the crystal lattice and the other is speculated to be associated with the organicmineral matrix.

  16. Assessing braze quality in the actively cooled Tore Supra phase III outboard pump limiter

    International Nuclear Information System (INIS)

    Hygren, R.; Lutz, T.; Miller, J.

    1994-01-01

    This paper discusses the assessment of quality of brazing of pyrolytic graphite (PG) armor brazed to copper tubes in Tore Supra's Phase III Outboard Pump Limiter (OPL). The limiter head is a bank of 14 water-cooled copper tubes with several hundred brazed PG tiles. Braze quality was first assessed through pre-service qualification testing of individual copper/tiles assemblies. The quality of brazes was evaluated using (non-destructive) transient heating (open-quotes hot waterclose quotes) tests performed in the high temperature, high pressure flow loop at Sandia's Plasma Materials Test Facility. The surface temperatures of tiles were monitored with an infra-red (IR) camera as water at 120 degrees C water at about 2.07 MPa (300 psi) passed through a tube assembly initially at 30 degrees C. For tiles with braze voids or cracks, the surface temperatures lagged behind those of adjacent well bonded tiles. Temperature lags were correlated with flaw sizes observed during repairs using a detailed 2-D heat transfer analyses. open-quotes Badclose quotes tiles, i.e., temperature lags of 10-20 degrees C depending upon tile's size, were easy to detect and, when removed, revealed braze voids of roughly 50% of the joint area. 11 of the 14 tubes were rebrazed after bad tiles were detected and removed. Three tubes were re-brazed twice

  17. Research ICT Africa - Phase III | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    During this phase, RIA will construct an African index of ICT policy and regulations; establish a network structure suitable for growth and the integration of North Africa; refine its policy influence and dissemination strategy; integrate its supply- and demand-side data and triangulate it with the telecommunication regulatory ...

  18. Uranium (III)-Plutonium (III) co-precipitation in molten chloride

    Science.gov (United States)

    Vigier, Jean-François; Laplace, Annabelle; Renard, Catherine; Miguirditchian, Manuel; Abraham, Francis

    2018-02-01

    Co-management of the actinides in an integrated closed fuel cycle by a pyrochemical process is studied at the laboratory scale in France in the CEA-ATALANTE facility. In this context the co-precipitation of U(III) and Pu(III) by wet argon sparging in LiCl-CaCl2 (30-70 mol%) molten salt at 705 °C is studied. Pu(III) is prepared in situ in the molten salt by carbochlorination of PuO2 and U(III) is then introduced as UCl3 after chlorine purge by argon to avoid any oxidation of uranium up to U(VI) by Cl2. The oxide conversion yield through wet argon sparging is quantitative. However, the preferential oxidation of U(III) in comparison to Pu(III) is responsible for a successive conversion of the two actinides, giving a mixture of UO2 and PuO2 oxides. Surprisingly, the conversion of sole Pu(III) in the same conditions leads to a mixture of PuO2 and PuOCl, characteristic of a partial oxidation of Pu(III) to Pu(IV). This is in contrast with coconversion of U(III)-Pu(III) mixtures but in agreement with the conversion of Ce(III).

  19. Treatment-related death in patients with small-cell lung cancer in phase III trials over the last two decades.

    Directory of Open Access Journals (Sweden)

    Nobuaki Ochi

    Full Text Available INTRODUCTION: Treatment-related death (TRD remains a serious problem in small-cell lung cancer (SCLC, despite recent improvements in supportive care. However, few studies have formally assessed time trends in the proportion of TRD over the past two decades. The aim of this study was to determine the frequency and pattern of TRD over time. METHODS: We examined phase 3 trials conducted between 1990 and 2010 to address the role of systemic treatment for SCLC. The time trend was assessed using linear regression analysis. RESULTS: In total, 97 trials including nearly 25,000 enrolled patients were analyzed. The overall TRD proportion was 2.95%. Regarding the time trend, while it was not statistically significant, it tended to decrease, with a 0.138% decrease per year and 2.76% decrease per two decades. The most common cause of death was febrile neutropenia without any significant time trend in its incidence over the years examined (p = 0.139. However, deaths due to febrile neutropenia as well as all causes in patients treated with non-platinum chemotherapy increased significantly (p = 0.033. CONCLUSIONS: The overall TRD rate has been low, but not negligible, in phase III trials for SCLC over the past two decades.

  20. Cd Mobility in Anoxic Fe-Mineral-Rich Environments - Potential Use of Fe(III)-Reducing Bacteria in Soil Remediation

    Science.gov (United States)

    Muehe, E. M.; Adaktylou, I. J.; Obst, M.; Schröder, C.; Behrens, S.; Hitchcock, A. P.; Tylsizczak, T.; Michel, F. M.; Krämer, U.; Kappler, A.

    2014-12-01

    Agricultural soils are increasingly burdened with heavy metals such as Cd from industrial sources and impure fertilizers. Metal contaminants enter the food chain via plant uptake from soil and negatively affect human and environmental health. New remediation approaches are needed to lower soil metal contents. To apply these remediation techniques successfully, it is necessary to understand how soil microbes and minerals interact with toxic metals. Here we show that microbial Fe(III) reduction initially mobilizes Cd before its immobilization under anoxic conditions. To study how microbial Fe(III) reduction influences Cd mobility, we isolated a new Cd-tolerant, Fe(III)-reducing Geobacter sp. from a heavily Cd-contaminated soil. In lab experiments, this Geobacter strain first mobilized Cd from Cd-loaded Fe(III) hydroxides followed by precipitation of Cd-bearing mineral phases. Using Mössbauer spectroscopy and scanning electron microscopy, the original and newly formed Cd-containing Fe(II) and Fe(III) mineral phases, including Cd-Fe-carbonates, Fe-phosphates and Fe-(oxyhydr)oxides, were identified and characterized. Using energy-dispersive X-ray spectroscopy and synchrotron-based scanning transmission X-ray microscopy, Cd was mapped in the Fe(II) mineral aggregates formed during microbial Fe(III) reduction. Microbial Fe(III) reduction mobilizes Cd prior to its precipitation in Cd-bearing mineral phases. The mobilized Cd could be taken up by phytoremediating plants, resulting in a net removal of Cd from contaminated sites. Alternatively, Cd precipitation could reduce Cd bioavailability in the environment, causing less toxic effects to crops and soil microbiota. However, the stability and thus bioavailability of these newly formed Fe-Cd mineral phases needs to be assessed thoroughly. Whether phytoremediation or immobilization of Cd in a mineral with reduced Cd bioavailability are feasible mechanisms to reduce toxic effects of Cd in the environment remains to be

  1. Epitaxial III-V nanowires on silicon for vertical devices

    NARCIS (Netherlands)

    Bakkers, E.P.A.M.; Borgström, M.T.; Einden, Van Den W.; Weert, van M.H.M.; Helman, A.; Verheijen, M.A.

    2006-01-01

    We show the epitaxial integration of III-V semiconductor nanowires with silicon technology. The wires are grown by the Vapor-Liquid-Solid (VLS) mechanism with laser ablation as well as metal organic vapor phase epitaxy. The VLS growth enables the fabrication of complex axial and radial

  2. Stability hierarchy between Piracetam forms I, II, and III from experimental pressure-temperature diagrams and topological inferences.

    Science.gov (United States)

    Toscani, Siro; Céolin, René; Minassian, Léon Ter; Barrio, Maria; Veglio, Nestor; Tamarit, Josep-Lluis; Louër, Daniel; Rietveld, Ivo B

    2016-01-30

    The trimorphism of the active pharmaceutical ingredient piracetam is a famous case of polymorphism that has been frequently revisited by many researchers. The phase relationships between forms I, II, and III were ambiguous because they seemed to depend on the heating rate of the DSC and on the history of the samples or they have not been observed at all (equilibrium II-III). In the present paper, piezo-thermal analysis and high-pressure differential thermal analysis have been used to elucidate the positions of the different solid-solid and solid-liquid equilibria. The phase diagram, involving the three solid phases, the liquid phase and the vapor phase, has been constructed. It has been shown that form III is the high-pressure, low-temperature form and the stable form at room temperature. Form II is stable under intermediary conditions and form I is the low pressure, high temperature form, which possesses a stable melting point. The present paper demonstrates the strength of the topological approach based on the Clapeyron equation and the alternation rule when combined with high-pressure measurements. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Computational advances in transition phase analysis

    International Nuclear Information System (INIS)

    Morita, K.; Kondo, S.; Tobita, Y.; Shirakawa, N.; Brear, D.J.; Fischer, E.A.

    1994-01-01

    In this paper, historical perspective and recent advances are reviewed on computational technologies to evaluate a transition phase of core disruptive accidents in liquid-metal fast reactors. An analysis of the transition phase requires treatment of multi-phase multi-component thermohydraulics coupled with space- and energy-dependent neutron kinetics. Such a comprehensive modeling effort was initiated when the program of SIMMER-series computer code development was initiated in the late 1970s in the USA. Successful application of the latest SIMMER-II in USA, western Europe and Japan have proved its effectiveness, but, at the same time, several areas that require further research have been identified. Based on the experience and lessons learned during the SIMMER-II application through 1980s, a new project of SIMMER-III development is underway at the Power Reactor and Nuclear Fuel Development Corporation (PNC), Japan. The models and methods of SIMMER-III are briefly described with emphasis on recent advances in multi-phase multi-component fluid dynamics technologies and their expected implication on a future reliable transition phase analysis. (author)

  4. Photo-induced charge-transfer phase transition of rubidium manganese hexacyanoferrate in ferromagnetic and paramagnetic states

    International Nuclear Information System (INIS)

    Tokoro, Hiroko; Hashimoto, Kazuhito; Ohkoshi, Shin-ichi

    2007-01-01

    A charge transfer phase transition with thermal hysteresis loop is observed in a series of rubidium manganese hexacyanoferrates, RbMn[Fe(China) 6 ] (1), Rb 0.88 Mn[Fe(China) 6 ] 0.96 .0.6H 2 O (2), and Rb 0.97 Mn[Fe(China) 6 ] 0.99 .0.2H 2 O (3). This phase transition is accompanied by a structural change from cubic (F4-bar 3m) to tetragonal (I4-bar m2). Its high-temperature (HT) and low-temperature (LT) phases are composed of Mn II (S=2/5)NC-Fe III (S=1/2) and Mn III (S=2)-NC-Fe II (S=0), respectively. The phase transition is caused by a metal-to-metal charge transfer from Mn II to Fe III and a Jahn-Teller distortion of the produced Mn III ion. At the ferromagnetic state in LT phase of 2, the photo-induced phase transition is observed, i.e., magnetization is quenched by the irradiation with only one shot of laser pulse. This phenomenon is caused by a photo-induced phase transition from the LT phase to the HT phase. In 3, optical switching between LT and HT phases at room temperature in paramagnetic region is observed

  5. Intravitreal sirolimus for the treatment of geographic atrophy: results of a phase I/II clinical trial.

    Science.gov (United States)

    Petrou, Philip A; Cunningham, Denise; Shimel, Katherine; Harrington, Molly; Hammel, Keri; Cukras, Catherine A; Ferris, Frederick L; Chew, Emily Y; Wong, Wai T

    2014-12-18

    To investigate the safety and effects of intravitreal sirolimus for the potential treatment of geographic atrophy (GA). The study was a single-center, open-label, phase I/II trial enrolling six participants with bilateral GA treated with intravitreal sirolimus in only one randomly assigned eye, with the fellow eye as control. The primary efficacy outcome measure was the change in total GA area from baseline on color fundus photography (CFP); secondary outcomes included changes in GA area on fundus autofluorescence (FAF), visual acuity, central retinal thickness (CRT), and macular sensitivity from baseline. Although no systemic adverse events were attributed to treatment, two of six participants had ocular adverse events that were possibly associated. The treated eye of one participant developed abnormal paralesional changes on FAF that were associated with accelerated retinal thinning. This accelerated retinal thinning was also seen in the treated eye of a second participant. Because of concern that these events were associated with treatment, treatment was suspended. Comparisons of treated and fellow eyes for change in visual acuity, change in GA area, and change in CRT showed no evidence of treatment benefit and generally favored the untreated fellow eye. While paralesional FAF changes and rapid retinal thinning observed are potentially part of the natural course of GA, they may possibly be related to treatment. No general evidence of anatomical or functional benefit was detected in treated eyes. Further data on intravitreal sirolimus for GA treatment will be available from a larger phase II trial. (ClinicalTrials.gov number, NCT01445548.). Copyright 2015 The Association for Research in Vision and Ophthalmology, Inc.

  6. Novel concepts for the compression of large volumes of carbon dioxide-phase III

    Energy Technology Data Exchange (ETDEWEB)

    Moore, J. Jeffrey [Southwest Research Inst., San Antonio, TX (United States); Allison, Timothy C. [Southwest Research Inst., San Antonio, TX (United States); Evans, Neal D. [Southwest Research Inst., San Antonio, TX (United States); Moreland, Brian [Southwest Research Inst., San Antonio, TX (United States); Hernandez, Augusto J. [Southwest Research Inst., San Antonio, TX (United States); Day, Meera [Southwest Research Inst., San Antonio, TX (United States); Ridens, Brandon L. [Southwest Research Inst., San Antonio, TX (United States)

    2014-06-30

    and tested in a closed loop compressor facility using CO2 . Both test programs successfully demonstrated good performance and mechanical behavior. In Phase III, a pilot compression plant consisting of a multi-stage centrifugal compressor with cooled diaphragm technology has been designed, constructed, and tested. Comparative testing of adiabatic and cooled tests at equivalent inlet conditions shows that the cooled diaphragms reduce power consumption by 3-8% when the compressor is operated as a back-to-back unit and by up to 9% when operated as a straight-though compressor with no intercooler. The power savings, heat exchanger effectiveness, and temperature drops for the cooled diaphragm were all slightly higher than predicted values but showed the same trends.

  7. A phase III study of adjuvant chemotherapy in advanced nasopharyngeal carcinoma patients

    International Nuclear Information System (INIS)

    Chi, K.-H.; Chang, Y.-C.; Guo, W.-Y.; Leung, M.-J.; Shiau, C.-Y.; Chen, S.-Y; Wang, L.-W.; Lai, Y.-L.; Hsu, M.-M.; Lian, S.-L.; Chang, C.-H.; Liu, T.-W.; Chin, Y.-H.; Yen, S.-H.; Perng, C.-H.; Chen, Kuang Y.

    2002-01-01

    Purpose: To evaluate the role of adjuvant chemotherapy in locally advanced nasopharyngeal carcinoma (NPC) patients, we conducted a randomized Phase III trial comparing radiotherapy (RT) followed by adjuvant chemotherapy to RT alone in patients with advanced NPC. Methods and Materials: Between November 1994 and March 1999, 157 patients with Stage IV, M 0 (UICC/AJCC, 1992) advanced NPC disease were randomized to receive standard radiotherapy, as follows: 35-40 fractions, 1.8-2.0 Gy/fraction/day, 5 days/week, to a total dose 70-72 Gy with or without 9 weekly cycles of 24-h infusional chemotherapy (20 mg/m 2 cisplatin, 2,200 mg/m 2 5-fluorouracil, and 120 mg/m 2 leucovorin) after RT. Of 157 patients enrolled, 154 (77 radiotherapy, 77 combined therapy) were evaluable for survival and toxicity analysis. Results: With a median follow-up of 49.5 months, the 5-year overall survival and relapse-free survival rates were 60.5% vs. 54.5% (p = 0.5) and 49.5% vs. 54.4% (p = 0.38) for the radiotherapy-alone group and the combined radiotherapy and adjuvant chemotherapy group, respectively. The Cox regression showed that the hazard rates ratio of combined treatment to RT alone was 0.673 (p value = 0.232); the 95% confidence interval was 0.352 and 1.288, respectively. Patients who received combined treatment had a lower systemic relapse rate than radiotherapy-alone patients, according to relapse pattern analysis. The incidence of leukopenia (≥ Grade 3) occurred in 17 out of 819 (2.1%) cycles of weekly chemotherapy. No patient developed moderate to severe mucositis (≥ Grade 3). Conclusions: We conclude that adjuvant chemotherapy after RT for patients with advanced NPC has no benefit for overall survival or relapse-free survival

  8. Column Chromatography Of Co(II), Zn(II) And Eu(III) Using Pistachio Shell And Different Mobile Phases

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Fattah, A A [Nuclear Chemistry Department, Radioisotopes Production Division, Hot Laboratories Centre, Atomic Energy Authority, Cairo (Egypt)

    2009-07-01

    Pistachio shell particles (0.5-1 mm) have been applied as the stationary phase for studying the column chromatography of Co(II), Zn(II) and Eu(III) at room temperature; 26{sup +}-{sup 1}oC. This solid sorbent has been characterized by thermogravimetric analysis, infra-red spectroscopy and X-ray diffraction. Its surface area and percent of swelling have been also determined. Different eluting agents have been used for eluting the sorbed elements. The elution curves have been done from which the distribution coefficients (K{sub d}), number of theoretical plates (N) and heights equivalent to theoretical plates (H) have been determined. Column performance studies have been conducted for a representative system under certain experimented conditions and Van Deemter equation has been applied. Thermodynamic studies have been applied and thermodynamic functions ( {delta}G{sup 0} ,{delta}H{sup 0} and{delta} S{sup 0}) have been calculated for this representative system by determining K{sub d} at three different room temperatures (18, 26 and 37{sup +}-{sup 1o}C)

  9. "cART intensification by the HIV-1 Tat B clade vaccine: progress to phase III efficacy studies".

    Science.gov (United States)

    Cafaro, Aurelio; Sgadari, Cecilia; Picconi, Orietta; Tripiciano, Antonella; Moretti, Sonia; Francavilla, Vittorio; Pavone Cossut, Maria Rosaria; Buttò, Stefano; Cozzone, Giovanni; Ensoli, Fabrizio; Monini, Paolo; Ensoli, Barbara

    2018-02-01

    In spite of its success at suppressing HIV replication, combination antiretroviral therapy (cART) only partially reduces immune dysregulation and loss of immune functions. These cART-unmet needs appear to be due to persistent virus replication and cell-to-cell transmission in reservoirs, and are causes of increased patients' morbidity and mortality. Up to now, therapeutic interventions aimed at cART-intensification by attacking the virus reservoir have failed. Areas covered: We briefly review the rationale and clinical development of Tat therapeutic vaccine in cART-treated subjects in Italy and South Africa (SA). Vaccination with clade-B Tat induced cross-clade neutralizing antibodies, immune restoration, including CD4 + T cell increase particularly in low immunological responders, and reduction of proviral DNA. Phase III efficacy trials in SA are planned both in adult and pediatric populations. Expert commentary: We propose the Tat therapeutic vaccine as a pathogenesis-driven intervention that effectively intensifies cART and may lead to a functional cure and provide new perspectives for prevention and virus eradication strategies.

  10. Nature of the Blue-Phase-III endash isotropic critical point: An analogy with the liquid-gas transition

    International Nuclear Information System (INIS)

    Anisimov, M.A.; Agayan, V.A.; Collings, P.J.

    1998-01-01

    The analogy with the liquid-gas critical point is analyzed to clarify the nature of the pretransitional behavior of physical properties in the vicinity of the Blue-Phase-III endash isotropic transition in chiral liquid crystalline systems. The analogy is unusual: temperature serves as the ordering field and entropy plays the role of the order parameter. Both mean field and parametric equations of state are formulated in terms of scaling fields. The scaling fields are linear combinations of the physical fields, which are temperature and chirality. It is shown that mixing of the physical field variables naturally leads to a strong asymmetry with respect to the transition temperature in the behavior of the physical properties that cannot be described by simple power laws. While the mean field theory gives a good description of the experimental data, the scaling theory, if one incorporates mixing of the field variables, gives even better agreement with the experimental data, placing this transition in the same universality class as the three-dimensional Ising model. copyright 1998 The American Physical Society

  11. The UK MK III GCR experimental physics programme at AEE Winfrith

    Energy Technology Data Exchange (ETDEWEB)

    Johnstone, I

    1972-06-15

    The UK programme of reactor physics experiments in support of the Mk III GCR project started in 1968/69 and has now reached its third main phase. The overall programme is broadly summarised in this report.

  12. Gemcitabine Plus Docetaxel Versus Docetaxel in Patients With Predominantly Human Epidermal Growth Factor Receptor 2-Negative Locally Advanced or Metastatic Breast Cancer: A Randomized, Phase III Study by the Danish Breast Cancer Cooperative Group

    DEFF Research Database (Denmark)

    Nielsen, Dorte L; Bjerre, Karsten D; Jakobsen, Erik H

    2011-01-01

    PURPOSE The objective of this phase III study was to compare the efficacy of gemcitabine plus docetaxel (GD) versus docetaxel in patients with advanced breast cancer. PATIENTS AND METHODS Predominantly human epidermal growth factor receptor 2 (HER2) -negative patients were randomly assigned...

  13. Methods for improved growth of group III nitride buffer layers

    Science.gov (United States)

    Melnik, Yurity; Chen, Lu; Kojiri, Hidehiro

    2014-07-15

    Methods are disclosed for growing high crystal quality group III-nitride epitaxial layers with advanced multiple buffer layer techniques. In an embodiment, a method includes forming group III-nitride buffer layers that contain aluminum on suitable substrate in a processing chamber of a hydride vapor phase epitaxy processing system. A hydrogen halide or halogen gas is flowing into the growth zone during deposition of buffer layers to suppress homogeneous particle formation. Some combinations of low temperature buffers that contain aluminum (e.g., AlN, AlGaN) and high temperature buffers that contain aluminum (e.g., AlN, AlGaN) may be used to improve crystal quality and morphology of subsequently grown group III-nitride epitaxial layers. The buffer may be deposited on the substrate, or on the surface of another buffer. The additional buffer layers may be added as interlayers in group III-nitride layers (e.g., GaN, AlGaN, AlN).

  14. Adaptive nonlinear control of single-phase to three-phase UPS system

    Directory of Open Access Journals (Sweden)

    Kissaoui M.

    2014-01-01

    Full Text Available This work deals with the problems of uninterruptible power supplies (UPS based on the single-phase to three-phase converters built in two stages: an input bridge rectifier and an output three phase inverter. The two blocks are joined by a continuous intermediate bus. The objective of control is threefold: i power factor correction “PFC”, ii generating a symmetrical three-phase system at the output even if the load is unknown, iii regulating the DC bus voltage. The synthesis of controllers has been reached by two nonlinear techniques that are the sliding mode and adaptive backstepping control. The performances of regulators have been validated by numerical simulation in MATLAB / SIMULINK.

  15. Clinical impact of tumor location on the colon cancer survival and recurrence: analyses of pooled data from three large phase III randomized clinical trials.

    Science.gov (United States)

    Aoyama, Toru; Kashiwabara, Kosuke; Oba, Koji; Honda, Michitaka; Sadahiro, Sotaro; Hamada, Chikuma; Maeda, Hiromichi; Mayanagi, Shuhei; Kanda, Mitsuro; Sakamoto, Junichi; Saji, Shigetoyo; Yoshikawa, Takaki

    2017-11-01

    The aim of the present study was to determine whether or not the overall survival (OS) and disease-free survival (DFS) were affected by the tumor location in patients who underwent curative resection for colon cancer in a pooled analysis of three large phase III studies performed in Japan. In total, 4029 patients were included in the present study. Patients were classified as having right-side colon cancer (RC) if the primary tumor was located in the cecum, ascending colon, hepatic flexure or transverse colon, and left-side colon cancer (LCC) if the tumor site was within the splenic flexure, descending colon, sigmoid colon or recto sigmoid junction. The risk factors for the OS and DFS were analyzed. In the present study, 1449 patients were RC, and 2580 were LCC. The OS rates at 3 and 5 years after surgery were 87.6% and 81.6% in the RC group and 91.5% and 84.5% in the LCC group, respectively. Uni- and multivariate analyses showed that RRC increased the risk of death by 19.7% (adjusted hazard ratio = 1.197; 95% confidence interval, 1.020-1.408; P = 0.0272). In contrast, the DFS was similar between the two locations. The present study confirmed that the tumor location was a risk factor for the OS in patients who underwent curative treatment for colon cancer. Tumor location may, therefore, need to be considered a stratification factor in future phase III trials of colon cancer. © 2017 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.

  16. Phase I/II Pilot Study of Mixed Chimerism to Treat Inherited Metabolic Disorders

    Science.gov (United States)

    2017-11-15

    Hurler Syndrome (MPS I); Hurler-Scheie Syndrome; Hunter Syndrome (MPS II); Sanfilippo Syndrome (MPS III); Krabbe Disease (Globoid Leukodystrophy); Metachromatic Leukodystrophy (MLD); Adrenoleukodystrophy (ALD and AMN); Sandhoff Disease; Tay Sachs Disease; Pelizaeus Merzbacher (PMD); Niemann-Pick Disease; Alpha-mannosidosis

  17. A phase I/II exploratory clinical trial for intracordal injection of recombinant hepatocyte growth factor for vocal fold scar and sulcus.

    Science.gov (United States)

    Hirano, Shigeru; Kawamoto, Atsuhiko; Tateya, Ichiro; Mizuta, Masanobu; Kishimoto, Yo; Hiwatashi, Nao; Kawai, Yoshitaka; Tsuji, Takuya; Suzuki, Ryo; Kaneko, Mami; Naito, Yasushi; Kagimura, Tatsuo; Nakamura, Tatsuo; Kanemaru, Shin-Ichi

    2018-04-01

    Vocal fold scar and sulcus are intractable diseases with no effective established treatments. Hepatocyte growth factor (HGF) has preclinically proven to have potent antifibrotic and regenerative effects on vocal fold scar. The current Phase I/II clinical trial aims to examine the safety and effectiveness of intracordal injection of a recombinant human HGF drug for patients with vocal fold scar or sulcus. This is an open-label, dose-escalating, first-in-human clinical trial. Eighteen patients with bilateral vocal fold scar or sulcus were enrolled and divided into three groups: Step I received 1 μg of HGF per vocal fold; Step II received 3 μg of HGF; and Step III received 10 μg of HGF. Injections were administered once weekly for 4 weeks. The protocol treatment was performed starting with Step I and escalating to Step III. Patients were followed for 6 months post-treatment. Local and systemic safety aspects were examined as primary endpoints, and therapeutic effects were assessed as secondary endpoints using voice handicap index-10; maximum phonation time; vocal fold vibratory amplitude; grade, rough, breathy, asthenic, strained scale; and jitter. The results indicated no serious drug-related adverse events in either the systemic or local examinations. In whole-subject analysis, voice handicap index-10, vocal fold vibratory amplitude, and grade, rough, breathy, asthenic, strained scale were significantly improved at 6 months, whereas maximum phonation time and jitter varied. There were no significant differences in phonatory data between the step groups. In conclusion, intracordal injection of a recombinant human HGF drug was safe, feasible, and potentially effective for human patients with vocal fold scar or sulcus. Copyright © 2017 John Wiley & Sons, Ltd.

  18. Heating Changes Bio-Schwertmannite Microstructure and Arsenic(III Removal Efficiency

    Directory of Open Access Journals (Sweden)

    Xingxing Qiao

    2017-01-01

    Full Text Available Schwertmannite (Sch is an efficient adsorbent for arsenic(III removal from arsenic(III-contaminated groundwater. In this study, bio-schertmannite was synthesized in the presence of dissolved ferrous ions and Acidithiobacillus ferrooxidans LX5 in a culture media. Bio-synthesized Sch characteristics, such as total organic carbon (TOC, morphology, chemical functional groups, mineral phase, specific surface area, and pore volume were systematically studied after it was dried at 105 °C and then heated at 250–550 °C. Differences in arsenic(III removal efficiency between 105 °C dried-sch and 250–550 °C heated-sch also were investigated. The results showed that total organic carbon content in Sch and Sch weight gradually decreased when temperature increased from 105 °C to 350 °C. Sch partly transformed to another nanocrystalline or amorphous phase above 350 °C. The specific surface area of 250 °C heated-sch was 110.06 m2/g compared to 5.14 m2/g for the 105 °C dried-sch. Total pore volume of 105 °C dried-sch was 0.025 cm3/g with 32.0% mesopore and 68.0% macropore. However, total pore volume of 250 °C heated-mineral was 0.106 cm3/g with 23.6% micropore, 33.0% mesopore, and 43.4% macropore. The arsenic(III removal efficiency from an initial 1 mg/L arsenic(III solution (pH 7.5 was 25.1% when 0.25 g/L of 105 °C dried-sch was used as adsorbent. However, this efficiency increased to 93.0% when using 250 °C heated-sch as adsorbent. Finally, the highest efficiency for arsenic(III removal was obtained with sch-250 °C due to high amounts of sorption sites in agreement with the high specific surface area (SSA obtained for this sample.

  19. OECD/NEA expert group on uncertainty analysis for criticality safety assessment: Results of benchmark on sensitivity calculation (phase III)

    Energy Technology Data Exchange (ETDEWEB)

    Ivanova, T.; Laville, C. [Institut de Radioprotection et de Surete Nucleaire IRSN, BP 17, 92262 Fontenay aux Roses (France); Dyrda, J. [Atomic Weapons Establishment AWE, Aldermaston, Reading, RG7 4PR (United Kingdom); Mennerdahl, D. [E Mennerdahl Systems EMS, Starvaegen 12, 18357 Taeby (Sweden); Golovko, Y.; Raskach, K.; Tsiboulia, A. [Inst. for Physics and Power Engineering IPPE, 1, Bondarenko sq., 249033 Obninsk (Russian Federation); Lee, G. S.; Woo, S. W. [Korea Inst. of Nuclear Safety KINS, 62 Gwahak-ro, Yuseong-gu, Daejeon 305-338 (Korea, Republic of); Bidaud, A.; Sabouri, P. [Laboratoire de Physique Subatomique et de Cosmologie LPSC, CNRS-IN2P3/UJF/INPG, Grenoble (France); Patel, A. [U.S. Nuclear Regulatory Commission (NRC), Washington, DC 20555-0001 (United States); Bledsoe, K.; Rearden, B. [Oak Ridge National Laboratory ORNL, M.S. 6170, P.O. Box 2008, Oak Ridge, TN 37831 (United States); Gulliford, J.; Michel-Sendis, F. [OECD/NEA, 12, Bd des Iles, 92130 Issy-les-Moulineaux (France)

    2012-07-01

    The sensitivities of the k{sub eff} eigenvalue to neutron cross sections have become commonly used in similarity studies and as part of the validation algorithm for criticality safety assessments. To test calculations of the sensitivity coefficients, a benchmark study (Phase III) has been established by the OECD-NEA/WPNCS/EG UACSA (Expert Group on Uncertainty Analysis for Criticality Safety Assessment). This paper presents some sensitivity results generated by the benchmark participants using various computational tools based upon different computational methods: SCALE/TSUNAMI-3D and -1D, MONK, APOLLO2-MORET 5, DRAGON-SUSD3D and MMKKENO. The study demonstrates the performance of the tools. It also illustrates how model simplifications impact the sensitivity results and demonstrates the importance of 'implicit' (self-shielding) sensitivities. This work has been a useful step towards verification of the existing and developed sensitivity analysis methods. (authors)

  20. Thermodecomposition of lanthanides (III) and ytrium (III) glucoheptonates

    International Nuclear Information System (INIS)

    Giolito, J.

    1987-01-01

    The lanthanides (III) and yttrium (III) glucoheptonates as well the D-glucoheptono 1-4 lactone were studied using common analytical methods, elemental microanalysis of carbon and hydrogen, thermogravimetry and differential scanning calorimetry. These compounds were prepared from the reaction between the lanthanides (III) and yttrium (III) hydroxides and glucoheptonic acid aqueous solution obtained by means of the delta lactone hydrolysis of this acid. After stoichiometric reaction the compounds were precipitated by the addition of absolute ethanol, washed with the same solvent and dried in desiccator. Thermogravimetric the (TG) curves of the lanthanides glucoheptonates of the ceric group present thermal profiles with enough differences permitting an easy caracterization of each compound and the yttrium (III) glucoheptonate TG curve showed a great similarity with the erbium (III) compound TG curve. The differential scanning calometry (DSC) curves showed endothermic and exothermic peaks by their shape, height and position (temperature) permit an easy and rapid identification of each compound specially if DSC and TG curves were examined simultaneously. (author) [pt

  1. The Moessbauer effect in Fe(III) HEDTA, Fe(III) EDTA, and Fe(III) CDTA compounds

    International Nuclear Information System (INIS)

    Prado, F.R.

    1989-01-01

    The dependence of Moessbauer spectra with pH value of Fe(III)HEDTA and Fe(III)CDTA compounds is studied. Informations on formation processes of LFe-O-FeL (L=ligand) type dimers by the relation of titration curves of Fe(III)EDTA, Fe(III)HEDTA and Fe(III)CDTA compounds with the series of Moessbauer spectra, are obtained. Some informations on Fe-O-Fe bond structure are also obtained. Comparing the titration curves with the series of Moessbauer spectra, it is concluded that the dimerization process begins when a specie of the form FeXOH α (X = EDTA, HEDTA, CDTA; α = -1, -2) arises. (M.C.K.) [pt

  2. III-nitrides on oxygen- and zinc-face ZnO substrates

    International Nuclear Information System (INIS)

    Namkoong, Gon; Burnham, Shawn; Lee, Kyoung-Keun; Trybus, Elaissa; Doolittle, W. Alan; Losurdo, Maria; Capezzuto, Pio; Bruno, Giovanni; Nemeth, Bill; Nause, Jeff

    2005-01-01

    The characteristics of III-nitrides grown on zinc- and oxygen-face ZnO by plasma-assisted molecular beam epitaxy were investigated. The reflection high-energy electron diffraction pattern indicates formation of a cubic phase at the interface between III-nitride and both Zn- and O-face ZnO. The polarity indicates that Zn-face ZnO leads to a single polarity, while O-face ZnO forms mixed polarity of III-nitrides. Furthermore, by using a vicinal ZnO substrate, the terrace-step growth of GaN was realized with a reduction by two orders of magnitude in the dislocation-related etch pit density to ∼10 8 cm -2 , while a dislocation density of ∼10 10 cm -2 was obtained on the on-axis ZnO substrates

  3. Europium (III) and americium (III) stability constants with humic acid

    International Nuclear Information System (INIS)

    Torres, R.A.; Choppin, G.R.

    1984-01-01

    The stability constants for tracer concentrations of Eu(III) and Am(III) complexes with a humic acid extracted from a lake-bottom sediment were measured using a solvent extraction system. The organic extractant was di(2-ethylhexyl)-phosphoric acid in toluene while the humate aqueous phase had a constant ionic strength of 0.1 M (NaClO 4 ). Aqueous humic acid concentrations were monitored by measuring uv-visible absorbances at approx.= 380 nm. The total carboxylate capacity of the humic acid was determined by direct potentiometric titration to be 3.86 +- 0.03 meq/g. The humic acid displayed typical characteristics of a polyelectrolyte - the apparent pKsub(a), as well as the calculated metal ion stability constants increased as the degree of ionization (α) increased. The binding data required a fit of two stability constants, β 1 and β 2 , such that for Eu, log β 1 = 8.86 α + 4.39, log β 2 = 3.55 α + 11.06 while for Am, log β 1 = 10.58 α + 3.84, log β 2 = 5.32 α + 10.42. With hydroxide, carbonate, and humate as competing ligands, the humate complex associated with the β 1 constant is calculated to be the dominant species for the trivalent actinides and lanthanides under conditions present in natural waters. (orig.)

  4. Type III bursts in interplanetary space - Fundamental or harmonic?

    Science.gov (United States)

    Dulk, G. A.; Steinberg, J. L.; Hoang, S.

    1984-01-01

    ISEE-3 spacecraft observation of 120 relatively simple, isolated bursts in the 30-1980 kHz range are the basis of the present study of Type III bursts in the solar wind. Several characteristics are identified for many of these bursts which imply that the mode of emission changes from predominantly fundamental plasma radiation during the rise phase to predominantly second harmonic during decay. The fundamental emission begins in time coincidence with the start of Langmuir waves, confirming the conventional belief in these waves' causation of Type III bursts. Attention is given to the characteristics of fundamental components, by comparison to harmonics, at km-wavelengths.

  5. Molecular and supramolecular speciations of solvent extraction systems based on malonamide and/or dialkyl-phosphoric acids for An(III)/Ln(III); Speciations moleculaire et supramoleculaire de systemes d'extraction liquide-liquide a base de malonamide et/ou d'acides dialkylphosphoriques pour la separation An(III)/Ln(III)

    Energy Technology Data Exchange (ETDEWEB)

    Gannaz, B

    2006-06-15

    The solvent extraction system used in the DIAMEX-SANEX process, developed for the actinide(III)/lanthanide(III) separation, is based on the use of mixtures of the malonamide DMDOHEMA and a dialkyl-phosphoric acid (HDEHP or HDHP), in hydrogenated tetra-propylene. The complexity of these systems urges on a novel approach to improve the conventional methods (thermodynamics, solvent extraction) which hardly explain the macroscopic behaviors observed (3. phase, over-stoichiometry). This approach combines studies on both supramolecular (VPO, SANS, SAXS) and molecular (liquid-liquid extraction, ESI-MS, IR, EXAFS) speciations of single extractant systems (DMDOHEMA or HDHP in in n-dodecane) and their mixture. In spite of safety constraints due to the handling of radio-material, they were used in the studies as much as possible, like for SAXS measurements on americium-containing samples, a worldwide first-time. In each of the investigated systems, actinides(III) and lanthanides(III) are extracted to the organic phase in polar cores of reversed micelles, the inner and outer-sphere compositions of which are proposed. Thus, the 4f and 5f cations are extracted by reversed micelles such as [(DMDOHEMA){sub 2}M(NO{sub 3}){sub 3}]{sub inn} (DMDOHEMA){sub x}(HNO{sub 3}){sub z}(H{sub 2}O){sub w}]{sub out} and M(DHP){sub 3}(HDHP){sub y-3}(H{sub 2}O){sub w} with y = 3 to 6, for the single extractant systems. In the case of the two extractants system, the less concentrated one acts like a co-surfactant regarding the mixed aggregate formation [(DMDOHEMA){sub 2}M(NO{sub 3}){sub 3-v}(DHP){sub v}]{sub inn} [(DMDOFIEMA){sub x}(HDHP){sub y}(HNO{sub 3})z(H{sub 2}O){sub w}]{sub out}. (author)

  6. Phase I study of cisplatin, vinorelbine, and concurrent thoracic radiotherapy for unresectable stage III non-small cell lung cancer

    International Nuclear Information System (INIS)

    Sekine, Ikuo

    2004-01-01

    To determine the recommended phase II dose of vinorelbine in combination with cisplatin and thoracic radiotherapy (TRT) in patients with unresectable stage III non-small cell lung cancer (NSCLC), 18 patients received cisplatin (80 mg/m 2 ) on day 1 and vinorelbine (20 mg/m 2 in level 1, and 25 mg/m 2 in level 2) on days 1 and 8 every 4 weeks for 4 cycles. TRT consisted of a single dose of 2 Gy once daily for 3 weeks followed by a rest of 4 days, and then the same TRT for 3 weeks to a total dose of 60 Gy. Fifteen (83%) patients received 60 Gy of TRT and 14 (78%) patients received 4 cycles of chemotherapy. Ten (77%) of 13 patients at level 1 and all 5 patients at level 2 developed grade 3-4 neutropenia. Four (31%) patients at level 1 and 3 (60%) patients at level 2 developed grade 3-4 infection. None developed ≥grade 3 esophagitis or lung toxicity. Dose-limiting toxicity was noted in 33% of the patients in level 1 and in 60% of the patients in level 2. The overall response rate (95% confidence interval) was 83% (59-96%) with 15 partial responses. The median survival time was 30.4 months, and the 1-year, 2-year, and 3-year survival rates were 72%, 61%, and 50%, respectively. In conclusion, the recommended dose is the level 1 dose, and this regimen is feasible and promising in patients with stage III NSCLC. (author)

  7. Successful completion of the Qinshan phase III nuclear power plant-a successful model for Chinese-Canadian cooperation

    International Nuclear Information System (INIS)

    Peng Xiaoxing

    2004-01-01

    This report documents Qinshan CANDU project construction and commissioning experience as well as management strategies and approaches that contributed to the successful completion of the project. The Qinshan phase III (CANDU) nuclear power plant was built in record times: Unit 1 achieved commercial operation on December 31, 2002 and Unit 2 on July 24, 2003, 43 days and 112 days ahead of schedule respectively. The reference plant design is the Wolsong 3 and 4 CANDU-6 units in the Republic of Korea. Improvements in design and construction methods allowed Unit 1 to be constructed in 51.5 Months from First Concrete to Criticality-a record in China for nuclear power plants. The key factors are project management and project management tools, quality assurance, construction methods (including open top construction, heavy lifts and modularization), electronic documentation with configuration control that provides up-to-date on-line information, CADDS design linked with material management, specialized material control including bar coding, and planning. The introduction of new design and construction techniques was achieved by combining conventional AECL practices with working experiences in China. The most advanced tools and techniques for achieving optimum construction quality, schedule and cost were used. Successful application of advanced project management methods and tools will benefit TQNPC in operation of the station, and the Chinese contractors in advancing their capabilities in future nuclear projects in China and enhancing their opportunities internationally. TQNPC's participation in Quality surveillance (QS) activities of nuclear steam plant (NSP) and Balance of Plant (BOP) offshore equipment benefited TQNPC in acquiring knowledge of specific equipment manufacturing processes, which can be applied to similar activities in China. China has established the capability of manufacturing CANDU fuel and becoming self-reliant in fuel supply. Excellent co-operation and

  8. Opioid Patient Controlled Analgesia (PCA) use during the Initial Experience with the IMPROVE PCA Trial: A Phase III Analgesic Trial for Hospitalized Sickle Cell Patients with Painful Episodes

    OpenAIRE

    Dampier, Carlton D.; Smith, Wally R.; Kim, Hae-Young; Wager, Carrie Greene; Bell, Margaret C.; Minniti, Caterina P.; Keefer, Jeffrey; Hsu, Lewis; Krishnamurti, Lakshmanan; Mack, A. Kyle; McClish, Donna; McKinlay, Sonja M.; Miller, Scott T.; Osunkwo, Ifeyinwa; Seaman, Phillip

    2011-01-01

    Opioid analgesics administered by patient-controlled analgesia (PCA) are frequently used for pain relief in children and adults with sickle cell disease (SCD) hospitalized for persistent vaso-occlusive pain, but optimum opioid dosing is not known. To better define PCA dosing recommendations, a multi-center phase III clinical trial was conducted comparing two alternative opioid PCA dosing strategies (HDLI-higher demand dose with low constant infusion or LDHI- lower demand dose and higher const...

  9. Phase I-II study of lenalidomide and alemtuzumab in refractory chronic lymphocytic leukemia (CLL): effects on T cells and immune checkpoints.

    Science.gov (United States)

    Winqvist, Maria; Mozaffari, Fariba; Palma, Marzia; Eketorp Sylvan, Sandra; Hansson, Lotta; Mellstedt, Håkan; Österborg, Anders; Lundin, Jeanette

    2017-01-01

    This phase I-II study explored safety, immunomodulatory and clinical effects of lenalidomide (weeks 1-16) and alemtuzumab (weeks 5-16) in 23 patients with refractory chronic lymphocytic leukemia. Most patients had Rai stage III/IV disease and were heavily pretreated (median 4 prior therapies), and 61% had del(17p)/del(11q). Eleven of 19 evaluable patients (58%) responded, with a median response duration of 12 months (1-29+); time to progression was short in non-responders. Lenalidomide had a narrow therapeutic dose range, 2.5 mg/day was not efficient, and maximum tolerated dose was 5 mg/day. Grade 3-4 neutropenia and thrombocytopenia occurred in 84 and 55%, 30% had febrile neutropenia, and CMV-reactivation requiring valganciclovir occurred in 30% of patients. The frequency of proliferating (Ki67 + ) CD8 + T cells was increased at week 4, with further increase in both the CD4 + and CD8 + subsets (p cells increased at week 4 as the frequency of effector memory cells increased in the CD8 + subset (p cells decreased in both the CD8 + and CD4 + subsets (p regulatory T cells was reduced (p T cells decreased, and effector memory T cells increased (p T cells increased at 30-week follow-up (p T cells, including increased proliferative activity and cytotoxic potential.

  10. Microbial Mineral Transformations at the Fe(II)/Fe(III) Redox Boundary for Solid Phase Capture of Strontium and Other Metal/Radionuclide Contaminants

    International Nuclear Information System (INIS)

    Ferris, F.G.; Roden, E.E.

    2000-01-01

    The migration of 90 Sr in groundwater is a significant environmental concern at former nuclear weapons production sites in the US and abroad. Although retardation of 90 Sr transport relative to mean groundwater velocity is known to occur in contaminated aquifers, Sr 2+ does not sorb as strongly to iron oxides and other mineral phases as do other metal-radionuclides contaminants. Thus, some potential exists for extensive 90 Sr migration from sources of contamination. Chemical or biological processes capable of retarding or immobilizing Sr 2+ in groundwater environments are of interest from the standpoint of understanding controls on subsurface Sr 2+ migration. In addition, it may be possible to exploit such processes for remediation of subsurface Sr contamination. In this study the authors examined the potential for the solid phase sorption and incorporation of Sr 2+ into carbonate minerals formed during microbial Fe(III) oxide reduction as a first step toward evaluating whether this process could be used to promote retardation of 90 Sr migrations in anaerobic subsurface environments. The demonstration of Sr 2+ capture in carbonate mineral phases formed during bacterial HFO reduction and urea hydrolysis suggests that microbial carbonate mineral formation could contribute to Sr 2+ retardation in groundwater environments. This process may also provide a mechanism for subsurface remediation of Sr 2+ and other divalent metal contaminants that form insoluble carbonate precipitates

  11. Sorption of trace amounts of gallium (III) on iron (III) oxide

    International Nuclear Information System (INIS)

    Music, S.; Gessner, M.; Wolf, R.H.H.

    1979-01-01

    The sorption of trace amounts of gallium(III) on iron(III) oxide has been studied as a function of pH. Optimum conditions have been found for the preconcentration of traces of gallium(III) by iron(III) oxide. The influence of surface active substances and of complexing agents on the sorption of trace amounts of gallium(III) on iron(III) oxide has been also studied. (orig.) [de