Ergonomics standards and guidelines for computer workstation design and the impact on users' health - a review.

Science.gov (United States)

Woo, E H C; White, P; Lai, C W K

2016-03-01

This paper presents an overview of global ergonomics standards and guidelines for design of computer workstations, with particular focus on their inconsistency and associated health risk impact. Overall, considerable disagreements were found in the design specifications of computer workstations globally, particularly in relation to the results from previous ergonomics research and the outcomes from current ergonomics standards and guidelines. To cope with the rapid advancement in computer technology, this article provides justifications and suggestions for modifications in the current ergonomics standards and guidelines for the design of computer workstations. Practitioner Summary: A research gap exists in ergonomics standards and guidelines for computer workstations. We explore the validity and generalisability of ergonomics recommendations by comparing previous ergonomics research through to recommendations and outcomes from current ergonomics standards and guidelines.

Stereotactic biopsy aided by a computer graphics workstation: experience with 200 consecutive cases.

Science.gov (United States)

Ulm, A J; Bova, F J; Friedman, W A

2001-12-01

The advent of modern computer technology has made it possible to examine not just the target point, but the entire trajectory in planning for stereotactic biopsies. Two hundred consecutive biopsies were performed by one surgeon, utilizing a computer graphics workstation. The target point, entry point, and complete trajectory were carefully scrutinized and adjusted to minimize potential complications. Pathologically abnormal tissue was obtained in 197 cases (98.5%). There was no mortality in this series. Symptomatic hemorrhages occurred in 4 cases (2%). Computer graphics workstations facilitate safe and effective biopsies in virtually any brain area.

Efficient Parallel Engineering Computing on Linux Workstations

Science.gov (United States)

Lou, John Z.

2010-01-01

A C software module has been developed that creates lightweight processes (LWPs) dynamically to achieve parallel computing performance in a variety of engineering simulation and analysis applications to support NASA and DoD project tasks. The required interface between the module and the application it supports is simple, minimal and almost completely transparent to the user applications, and it can achieve nearly ideal computing speed-up on multi-CPU engineering workstations of all operating system platforms. The module can be integrated into an existing application (C, C++, Fortran and others) either as part of a compiled module or as a dynamically linked library (DLL).

Flexible structure control experiments using a real-time workstation for computer-aided control engineering

Science.gov (United States)

Stieber, Michael E.

1989-01-01

A Real-Time Workstation for Computer-Aided Control Engineering has been developed jointly by the Communications Research Centre (CRC) and Ruhr-Universitaet Bochum (RUB), West Germany. The system is presently used for the development and experimental verification of control techniques for large space systems with significant structural flexibility. The Real-Time Workstation essentially is an implementation of RUB's extensive Computer-Aided Control Engineering package KEDDC on an INTEL micro-computer running under the RMS real-time operating system. The portable system supports system identification, analysis, control design and simulation, as well as the immediate implementation and test of control systems. The Real-Time Workstation is currently being used by CRC to study control/structure interaction on a ground-based structure called DAISY, whose design was inspired by a reflector antenna. DAISY emulates the dynamics of a large flexible spacecraft with the following characteristics: rigid body modes, many clustered vibration modes with low frequencies and extremely low damping. The Real-Time Workstation was found to be a very powerful tool for experimental studies, supporting control design and simulation, and conducting and evaluating tests withn one integrated environment.

Issues about home computer workstations and primary school children in Hong Kong: a pilot study.

Science.gov (United States)

Py Szeto, Grace; Tsui, Macy Mei Sze; Sze, Winky Wing Yu; Chan, Irene Sin Ting; Chung, Cyrus Chak Fai; Lee, Felix Wai Kit

2014-01-01

All around the world, there is a rising trend of computer use among young children especially at home; yet the computer furniture is usually not designed specifically for children's use. In Hong Kong, this creates an even greater problem as most people live in very small apartments in high-rise buildings. Most of the past research literature is focused on computer use in children in the school environment and not about the home setting. The present pilot study aimed to examine ergonomic issues in children's use of computers at home in Hong Kong, which has some unique home environmental issues. Fifteen children (six male, nine female) aged 8-11 years and their parents were recruited by convenience sampling. Participants were asked to provide information on their computer use habits and related musculoskeletal symptoms. Participants were photographed when sitting at the computer workstation in their usual postures and joint angles were measured. The participants used computers frequently for less than two hours daily and the majority shared their workstations with other family members. Computer furniture was designed more for adult use and a mismatch of furniture and body size was found. Ergonomic issues included inappropriate positioning of the display screen, keyboard, and mouse, as well as lack of forearm support and suitable backrest. These led to awkward or constrained postures while some postural problems may be habitual. Three participants reported neck and shoulder discomfort in the past 12 months and 4 reported computer-related discomfort. Inappropriate computer workstation settings may have adverse effects on children's postures. More research on workstation setup at home, where children may use their computers the most, is needed.

The effect of dynamic workstations on the performance of various computer and office-based tasks

NARCIS (Netherlands)

Burford, E.M.; Botter, J.; Commissaris, D.; Könemann, R.; Hiemstra-Van Mastrigt, S.; Ellegast, R.P.

2013-01-01

The effect of different workstations, conventional and dynamic, on different types of performance measures for several different office and computer based task was investigated in this research paper. The two dynamic workstations assessed were the Lifespan Treadmill Desk and the RightAngle

Comparison of computer workstation with film for detecting setup errors

International Nuclear Information System (INIS)

Fritsch, D.S.; Boxwala, A.A.; Raghavan, S.; Coffee, C.; Major, S.A.; Muller, K.E.; Chaney, E.L.

1997-01-01

Purpose/Objective: Workstations designed for portal image interpretation by radiation oncologists provide image displays and image processing and analysis tools that differ significantly compared with the standard clinical practice of inspecting portal films on a light box. An implied but unproved assumption associated with the clinical implementation of workstation technology is that patient care is improved, or at least not adversely affected. The purpose of this investigation was to conduct observer studies to test the hypothesis that radiation oncologists can detect setup errors using a workstation at least as accurately as when following standard clinical practice. Materials and Methods: A workstation, PortFolio, was designed for radiation oncologists to display and inspect digital portal images for setup errors. PortFolio includes tools to enhance images; align cross-hairs, field edges, and anatomic structures on reference and acquired images; measure distances and angles; and view registered images superimposed on one another. In a well designed and carefully controlled observer study, nine radiation oncologists, including attendings and residents, used PortFolio to detect setup errors in realistic digitally reconstructed portal (DRPR) images computed from the NLM visible human data using a previously described approach † . Compared with actual portal images where absolute truth is ill defined or unknown, the DRPRs contained known translation or rotation errors in the placement of the fields over target regions in the pelvis and head. Twenty DRPRs with randomly induced errors were computed for each site. The induced errors were constrained to a plane at the isocenter of the target volume and perpendicular to the central axis of the treatment beam. Images used in the study were also printed on film. Observers interpreted the film-based images using standard clinical practice. The images were reviewed in eight sessions. During each session five images were

Workstation computer systems for in-core fuel management

International Nuclear Information System (INIS)

Ciccone, L.; Casadei, A.L.

1992-01-01

The advancement of powerful engineering workstations has made it possible to have thermal-hydraulics and accident analysis computer programs operating efficiently with a significant performance/cost ratio compared to large mainframe computer. Today, nuclear utilities are acquiring independent engineering analysis capability for fuel management and safety analyses. Computer systems currently available to utility organizations vary widely thus requiring that this software be operational on a number of computer platforms. Recognizing these trends Westinghouse adopted a software development life cycle process for the software development activities which strictly controls the development, testing and qualification of design computer codes. In addition, software standards to ensure maximum portability were developed and implemented, including adherence to FORTRAN 77, and use of uniform system interface and auxiliary routines. A comprehensive test matrix was developed for each computer program to ensure that evolution of code versions preserves the licensing basis. In addition, the results of such test matrices establish the Quality Assurance basis and consistency for the same software operating on different computer platforms. (author). 4 figs

Children and computer use in the home: workstations, behaviors and parental attitudes.

Science.gov (United States)

Kimmerly, Lisa; Odell, Dan

2009-01-01

This study examines the home computer use of 26 children (aged 6-18) in ten upper middle class families using direct observation, typing tests, questionnaires and semi-structured interviews. The goals of the study were to gather information on how children use computers in the home and to understand how both parents and children perceive this computer use. Large variations were seen in computing skills, behaviors, and opinions, as well as equipment and workstation setups. Typing speed averaged over 40 words per minute for children over 13 years old, and less than 10 words per minute for children younger than 10. The results show that for this sample, Repetitive Stress Injury (RSI) concerns ranked very low among parents, whereas security and privacy concerns ranked much higher. Meanwhile, children's behaviors and workstations were observed to place children in awkward working postures. Photos showing common postures are presented. The greatest opportunity to improve children's work postures appears to be in providing properly-sized work surfaces and chairs, as well as education. Possible explanations for the difference between parental perception of computing risks and the physical reality of children's observed ergonomics are discussed and ideas for further research are proposed.

Workstations studies and radiation protection

International Nuclear Information System (INIS)

Lahaye, T.; Donadille, L.; Rehel, J.L.; Paquet, F.; Beneli, C.; Cordoliani, Y.S.; Vrigneaud, J.M.; Gauron, C.; Petrequin, A.; Frison, D.; Jeannin, B.; Charles, D.; Carballeda, G.; Crouail, P.; Valot, C.

2006-01-01

This day on the workstations studies for the workers follow-up, was organised by the research and health section. Devoted to the company doctors, for the competent persons in radiation protection, for the engineers of safety, it presented examples of methodologies and applications in the medical, industrial domain and the research, so contributing to a better understanding and an application of regulatory measures. The analysis of the workstation has to allow a reduction of the exposures and the risks and lead to the optimization of the medical follow-up. The agenda of this day included the different subjects as follow: evolution of the regulation in matter of demarcation of the regulated zones where the measures of workers protection are strengthened; presentation of the I.R.S.N. guide of help to the realization of a workstation study; implementation of a workstation study: case of radiology; the workstation studies in the research area; Is it necessary to impose the operational dosimetry in the services of radiodiagnostic? The experience feedback of a competent person in radiation protection (P.C.R.) in a hospital environment; radiation protection: elaboration of a good practices guide in medical field; the activities file in nuclear power plant: an evaluation tool of risks for the prevention. Methodological presentation and examples; insulated workstation study; the experience feedback of a provider; Contribution of the ergonomics to the determiners characterization in the ionizing radiation exposure situations;The workstations studies for the internal contamination in the fuel cycle facilities and the consideration of the results in the medical follow-up; R.E.L.I.R. necessity of workstation studies; the consideration of the human factor. (N.C.)

A computer graphics pilot project - Spacecraft mission support with an interactive graphics workstation

Science.gov (United States)

Hagedorn, John; Ehrner, Marie-Jacqueline; Reese, Jodi; Chang, Kan; Tseng, Irene

1986-01-01

The NASA Computer Graphics Pilot Project was undertaken to enhance the quality control, productivity and efficiency of mission support operations at the Goddard Operations Support Computing Facility. The Project evolved into a set of demonstration programs for graphics intensive simulated control room operations, particularly in connection with the complex space missions that began in the 1980s. Complex mission mean more data. Graphic displays are a means to reduce the probabilities of operator errors. Workstations were selected with 1024 x 768 pixel color displays controlled by a custom VLSI chip coupled to an MC68010 chip running UNIX within a shell that permits operations through the medium of mouse-accessed pulldown window menus. The distributed workstations run off a host NAS 8040 computer. Applications of the system for tracking spacecraft orbits and monitoring Shuttle payload handling illustrate the system capabilities, noting the built-in capabilities of shifting the point of view and rotating and zooming in on three-dimensional views of spacecraft.

Low Cost Desktop Image Analysis Workstation With Enhanced Interactive User Interface

Science.gov (United States)

Ratib, Osman M.; Huang, H. K.

1989-05-01

A multimodality picture archiving and communication system (PACS) is in routine clinical use in the UCLA Radiology Department. Several types workstations are currently implemented for this PACS. Among them, the Apple Macintosh II personal computer was recently chosen to serve as a desktop workstation for display and analysis of radiological images. This personal computer was selected mainly because of its extremely friendly user-interface, its popularity among the academic and medical community and its low cost. In comparison to other microcomputer-based systems the Macintosh II offers the following advantages: the extreme standardization of its user interface, file system and networking, and the availability of a very large variety of commercial software packages. In the current configuration the Macintosh II operates as a stand-alone workstation where images are imported from a centralized PACS server through an Ethernet network using a standard TCP-IP protocol, and stored locally on magnetic disk. The use of high resolution screens (1024x768 pixels x 8bits) offer sufficient performance for image display and analysis. We focused our project on the design and implementation of a variety of image analysis algorithms ranging from automated structure and edge detection to sophisticated dynamic analysis of sequential images. Specific analysis programs were developed for ultrasound images, digitized angiograms, MRI and CT tomographic images and scintigraphic images.

High-performance floating-point image computing workstation for medical applications

Science.gov (United States)

Mills, Karl S.; Wong, Gilman K.; Kim, Yongmin

1990-07-01

The medical imaging field relies increasingly on imaging and graphics techniques in diverse applications with needs similar to (or more stringent than) those of the military, industrial and scientific communities. However, most image processing and graphics systems available for use in medical imaging today are either expensive, specialized, or in most cases both. High performance imaging and graphics workstations which can provide real-time results for a number of applications, while maintaining affordability and flexibility, can facilitate the application of digital image computing techniques in many different areas. This paper describes the hardware and software architecture of a medium-cost floating-point image processing and display subsystem for the NeXT computer, and its applications as a medical imaging workstation. Medical imaging applications of the workstation include use in a Picture Archiving and Communications System (PACS), in multimodal image processing and 3-D graphics workstation for a broad range of imaging modalities, and as an electronic alternator utilizing its multiple monitor display capability and large and fast frame buffer. The subsystem provides a 2048 x 2048 x 32-bit frame buffer (16 Mbytes of image storage) and supports both 8-bit gray scale and 32-bit true color images. When used to display 8-bit gray scale images, up to four different 256-color palettes may be used for each of four 2K x 2K x 8-bit image frames. Three of these image frames can be used simultaneously to provide pixel selectable region of interest display. A 1280 x 1024 pixel screen with 1: 1 aspect ratio can be windowed into the frame buffer for display of any portion of the processed image or images. In addition, the system provides hardware support for integer zoom and an 82-color cursor. This subsystem is implemented on an add-in board occupying a single slot in the NeXT computer. Up to three boards may be added to the NeXT for multiple display capability (e

UWGSP6: a diagnostic radiology workstation of the future

Science.gov (United States)

Milton, Stuart W.; Han, Sang; Choi, Hyung-Sik; Kim, Yongmin

1993-06-01

The Univ. of Washington's Image Computing Systems Lab. (ICSL) has been involved in research into the development of a series of PACS workstations since the middle 1980's. The most recent research, a joint UW-IBM project, attempted to create a diagnostic radiology workstation using an IBM RISC System 6000 (RS6000) computer workstation and the X-Window system. While the results are encouraging, there are inherent limitations in the workstation hardware which prevent it from providing an acceptable level of functionality for diagnostic radiology. Realizing the RS6000 workstation's limitations, a parallel effort was initiated to design a workstation, UWGSP6 (Univ. of Washington Graphics System Processor #6), that provides the required functionality. This paper documents the design of UWGSP6, which not only addresses the requirements for a diagnostic radiology workstation in terms of display resolution, response time, etc., but also includes the processing performance necessary to support key functions needed in the implementation of algorithms for computer-aided diagnosis. The paper includes a description of the workstation architecture, and specifically its image processing subsystem. Verification of the design through hardware simulation is then discussed, and finally, performance of selected algorithms based on detailed simulation is provided.

Comparison of computer workstation with light box for detecting setup errors from portal images

International Nuclear Information System (INIS)

Boxwala, Aziz A.; Chaney, Edward L.; Fritsch, Daniel S.; Raghavan, Suraj; Coffey, Christopher S.; Major, Stacey A.; Muller, Keith E.

1999-01-01

Purpose: Observer studies were conducted to test the hypothesis that radiation oncologists using a computer workstation for portal image analysis can detect setup errors at least as accurately as when following standard clinical practice of inspecting portal films on a light box. Methods and Materials: In a controlled observer study, nine radiation oncologists used a computer workstation, called PortFolio, to detect setup errors in 40 realistic digitally reconstructed portal radiograph (DRPR) images. PortFolio is a prototype workstation for radiation oncologists to display and inspect digital portal images for setup errors. PortFolio includes tools for image enhancement; alignment of crosshairs, field edges, and anatomic structures on reference and acquired images; measurement of distances and angles; and viewing registered images superimposed on one another. The test DRPRs contained known in-plane translation or rotation errors in the placement of the fields over target regions in the pelvis and head. Test images used in the study were also printed on film for observers to view on a light box and interpret using standard clinical practice. The mean accuracy for error detection for each approach was measured and the results were compared using repeated measures analysis of variance (ANOVA) with the Geisser-Greenhouse test statistic. Results: The results indicate that radiation oncologists participating in this study could detect and quantify in-plane rotation and translation errors more accurately with PortFolio compared to standard clinical practice. Conclusions: Based on the results of this limited study, it is reasonable to conclude that workstations similar to PortFolio can be used efficaciously in clinical practice

Computed radiography and the workstation in a study of the cervical spine. Technical and cost implications

International Nuclear Information System (INIS)

Garcia, J. M.; Lopez-Galiacho, N.; Martinez, M.

1999-01-01

To demonstrate the advantages of computed radiography and the workstation in assessing the images acquired in a study of the cervical spine. Lateral projections of cervical spine obtained using a computed radiography system in 63 ambulatory patients were studied in a workstation. Images of the tip of the odontoid process. C1-C2, basion-opisthion and C7 were visualized prior to and after their transmission and processing, and the overall improvement in their diagnostic quality was assessed. The rate of detection of the tip of the odontoid process, C1-C2, the foramen magnum and C/ increased by 17,6, 11 and 14 percentage points, respectively. Image processing improved the diagnostic quality in over 75% of cases. Image processing in a workstation improved the visualization of the anatomical points being studied and the diagnostic quality of the images. These advantages as well as the possibility of transferring the images to a picture archiving and communication system (PACS) are convincing reasons for using digital radiography. (Author) 7 refs

The concepts and functions of a FEM workstation

International Nuclear Information System (INIS)

Brown, R.R.; Gloudeman, J.F.

1982-01-01

Recent advances in microprocessor-based computer hardware and associated software provide a basis for the development of a FEM workstation. The key requirements for such a workstation are reviewed and the recent hardware and software developments are discussed that make such a workstation both technically and economically feasible at this time. (orig.)

Computer-aided diagnosis workstation and network system for chest diagnosis based on multislice CT images

Science.gov (United States)

Satoh, Hitoshi; Niki, Noboru; Eguchi, Kenji; Moriyama, Noriyuki; Ohmatsu, Hironobu; Masuda, Hideo; Machida, Suguru

2008-03-01

Mass screening based on multi-helical CT images requires a considerable number of images to be read. It is this time-consuming step that makes the use of helical CT for mass screening impractical at present. To overcome this problem, we have provided diagnostic assistance methods to medical screening specialists by developing a lung cancer screening algorithm that automatically detects suspected lung cancers in helical CT images, a coronary artery calcification screening algorithm that automatically detects suspected coronary artery calcification and a vertebra body analysis algorithm for quantitative evaluation of osteoporosis likelihood by using helical CT scanner for the lung cancer mass screening. The function to observe suspicious shadow in detail are provided in computer-aided diagnosis workstation with these screening algorithms. We also have developed the telemedicine network by using Web medical image conference system with the security improvement of images transmission, Biometric fingerprint authentication system and Biometric face authentication system. Biometric face authentication used on site of telemedicine makes "Encryption of file" and Success in login" effective. As a result, patients' private information is protected. Based on these diagnostic assistance methods, we have developed a new computer-aided workstation and a new telemedicine network that can display suspected lesions three-dimensionally in a short time. The results of this study indicate that our radiological information system without film by using computer-aided diagnosis workstation and our telemedicine network system can increase diagnostic speed, diagnostic accuracy and security improvement of medical information.

[PACS-based endoscope image acquisition workstation].

Science.gov (United States)

Liu, J B; Zhuang, T G

2001-01-01

A practical PACS-based Endoscope Image Acquisition Workstation is here introduced. By a Multimedia Video Card, the endoscope video is digitized and captured dynamically or statically into computer. This workstation realizes a variety of functions such as the endoscope video's acquisition and display, as well as the editing, processing, managing, storage, printing, communication of related information. Together with other medical image workstation, it can make up the image sources of PACS for hospitals. In addition, it can also act as an independent endoscopy diagnostic system.

Computer-aided diagnosis workstation and telemedicine network system for chest diagnosis based on multislice CT images

Science.gov (United States)

Satoh, Hitoshi; Niki, Noboru; Eguchi, Kenji; Ohmatsu, Hironobu; Kakinuma, Ryutaru; Moriyama, Noriyuki

2009-02-01

Mass screening based on multi-helical CT images requires a considerable number of images to be read. It is this time-consuming step that makes the use of helical CT for mass screening impractical at present. Moreover, the doctor who diagnoses a medical image is insufficient in Japan. To overcome these problems, we have provided diagnostic assistance methods to medical screening specialists by developing a lung cancer screening algorithm that automatically detects suspected lung cancers in helical CT images, a coronary artery calcification screening algorithm that automatically detects suspected coronary artery calcification and a vertebra body analysis algorithm for quantitative evaluation of osteoporosis likelihood by using helical CT scanner for the lung cancer mass screening. The functions to observe suspicious shadow in detail are provided in computer-aided diagnosis workstation with these screening algorithms. We also have developed the telemedicine network by using Web medical image conference system with the security improvement of images transmission, Biometric fingerprint authentication system and Biometric face authentication system. Biometric face authentication used on site of telemedicine makes "Encryption of file" and "Success in login" effective. As a result, patients' private information is protected. We can share the screen of Web medical image conference system from two or more web conference terminals at the same time. An opinion can be exchanged mutually by using a camera and a microphone that are connected with workstation. Based on these diagnostic assistance methods, we have developed a new computer-aided workstation and a new telemedicine network that can display suspected lesions three-dimensionally in a short time. The results of this study indicate that our radiological information system without film by using computer-aided diagnosis workstation and our telemedicine network system can increase diagnostic speed, diagnostic accuracy and

Predicting Forearm Physical Exposures During Computer Work Using Self-Reports, Software-Recorded Computer Usage Patterns, and Anthropometric and Workstation Measurements.

Science.gov (United States)

Huysmans, Maaike A; Eijckelhof, Belinda H W; Garza, Jennifer L Bruno; Coenen, Pieter; Blatter, Birgitte M; Johnson, Peter W; van Dieën, Jaap H; van der Beek, Allard J; Dennerlein, Jack T

2017-12-15

Alternative techniques to assess physical exposures, such as prediction models, could facilitate more efficient epidemiological assessments in future large cohort studies examining physical exposures in relation to work-related musculoskeletal symptoms. The aim of this study was to evaluate two types of models that predict arm-wrist-hand physical exposures (i.e. muscle activity, wrist postures and kinematics, and keyboard and mouse forces) during computer use, which only differed with respect to the candidate predicting variables; (i) a full set of predicting variables, including self-reported factors, software-recorded computer usage patterns, and worksite measurements of anthropometrics and workstation set-up (full models); and (ii) a practical set of predicting variables, only including the self-reported factors and software-recorded computer usage patterns, that are relatively easy to assess (practical models). Prediction models were build using data from a field study among 117 office workers who were symptom-free at the time of measurement. Arm-wrist-hand physical exposures were measured for approximately two hours while workers performed their own computer work. Each worker's anthropometry and workstation set-up were measured by an experimenter, computer usage patterns were recorded using software and self-reported factors (including individual factors, job characteristics, computer work behaviours, psychosocial factors, workstation set-up characteristics, and leisure-time activities) were collected by an online questionnaire. We determined the predictive quality of the models in terms of R2 and root mean squared (RMS) values and exposure classification agreement to low-, medium-, and high-exposure categories (in the practical model only). The full models had R2 values that ranged from 0.16 to 0.80, whereas for the practical models values ranged from 0.05 to 0.43. Interquartile ranges were not that different for the two models, indicating that only for some

A RISC/UNIX workstation second stage trigger

International Nuclear Information System (INIS)

Foreman, W.M.; Amann, J.F.; Fu, S.; Kozlowski, T.; Naivar, F.J.; Oothoudt, M.A.; Shelley, F.

1992-01-01

Recent advances in Reduced Instruction Set Computer (RISC) workstations have greatly altered the economics of processing power available for experiments. In addition VME interfaces available for many of these workstations make it possible to use them in experiment frontends for filtering and compressing data. Such a second stage trigger has been implemented at LAMPF using a commercially available workstation and VME interface. The implementation is described and measurements of data transfer speeds are presented in this paper

Computers in nuclear medicine

International Nuclear Information System (INIS)

Giannone, Carlos A.

1999-01-01

This chapter determines: capture and observation of images in computers; hardware and software used, personal computers, networks and workstations. The use of special filters determine the quality image

A comparison between digital images viewed on a picture archiving and communication system diagnostic workstation and on a PC-based remote viewing system by emergency physicians.

Science.gov (United States)

Parasyn, A; Hanson, R M; Peat, J K; De Silva, M

1998-02-01

Picture Archiving and Communication Systems (PACS) make possible the viewing of radiographic images on computer workstations located where clinical care is delivered. By the nature of their work this feature is particularly useful for emergency physicians who view radiographic studies for information and use them to explain results to patients and their families. However, the high cost of PACS diagnostic workstations with fuller functionality places limits on the number of and therefore the accessibility to workstations in the emergency department. This study was undertaken to establish how well less expensive personal computer-based workstations would work to support these needs of emergency physicians. The study compared the outcome of observations by 5 emergency physicians on a series of radiographic studies containing subtle abnormalities displayed on both a PACS diagnostic workstation and on a PC-based workstation. The 73 digitized radiographic studies were randomly arranged on both types of workstation over four separate viewing sessions for each emergency physician. There was no statistical difference between a PACS diagnostic workstation and a PC-based workstation in this trial. The mean correct ratings were 59% on the PACS diagnostic workstations and 61% on the PC-based workstations. These findings also emphasize the need for prompt reporting by a radiologist.

Differences in ergonomic and workstation factors between computer office workers with and without reported musculoskeletal pain.

Science.gov (United States)

Rodrigues, Mirela Sant'Ana; Leite, Raquel Descie Veraldi; Lelis, Cheila Maira; Chaves, Thaís Cristina

2017-01-01

Some studies have suggested a causal relationship between computer work and the development of musculoskeletal disorders. However, studies considering the use of specific tools to assess workplace ergonomics and psychosocial factors in computer office workers with and without reported musculoskeletal pain are scarce. The aim of this study was to compare the ergonomic, physical, and psychosocial factors in computer office workers with and without reported musculoskeletal pain (MSP). Thirty-five computer office workers (aged 18-55 years) participated in the study. The following evaluations were completed: Rapid Upper Limb Assessment (RULA), Rapid Office Strain Assessment (ROSA), and Maastricht Upper Extremity Questionnaire revised Brazilian Portuguese version (MUEQ-Br revised). Student t-tests were used to make comparisons between groups. The computer office workers were divided into two groups: workers with reported MSP (WMSP, n = 17) and workers without positive report (WOMSP, n = 18). Those in the WMSP group showed significantly greater mean values in the total ROSA score (WMSP: 6.71 [CI95% :6.20-7.21] and WOMSP: 5.88 [CI95% :5.37-6.39], p = 0.01). The WMSP group also showed higher scores in the chair section of the ROSA, workstation of MUEQ-Br revised, and in the upper limb RULA score. The chair height and armrest sections from ROSA showed the higher mean values in workers WMSP compared to workers WOMSP. A positive moderate correlation was observed between ROSA and RULA total scores (R = 0.63, p ergonomics indexes for chair workstation and worse physical risk related to upper limb (RULA upper limb section) than workers without pain. However, there were no observed differences in workers with and without MSP regarding work-related psychosocial factors. The results suggest that inadequate workstation conditions, specifically the chair height, arm and back rest, are linked to improper upper limb postures and that these factors are contributing to

CALIPSO: an interactive image analysis software package for desktop PACS workstations

Science.gov (United States)

Ratib, Osman M.; Huang, H. K.

1990-07-01

The purpose of this project is to develop a low cost workstation for quantitative analysis of multimodality images using a Macintosh II personal computer. In the current configuration the Macintosh operates as a stand alone workstation where images are imported either from a central PACS server through a standard Ethernet network or recorded through video digitizer board. The CALIPSO software developed contains a large variety ofbasic image display and manipulation tools. We focused our effort however on the design and implementation ofquantitative analysis methods that can be applied to images from different imaging modalities. Analysis modules currently implemented include geometric and densitometric volumes and ejection fraction calculation from radionuclide and cine-angiograms Fourier analysis ofcardiac wall motion vascular stenosis measurement color coded parametric display of regional flow distribution from dynamic coronary angiograms automatic analysis ofmyocardial distribution ofradiolabelled tracers from tomoscintigraphic images. Several of these analysis tools were selected because they use similar color coded andparametric display methods to communicate quantitative data extracted from the images. 1. Rationale and objectives of the project Developments of Picture Archiving and Communication Systems (PACS) in clinical environment allow physicians and radiologists to assess radiographic images directly through imaging workstations (''). This convenient access to the images is often limited by the number of workstations available due in part to their high cost. There is also an increasing need for quantitative analysis ofthe images. During thepast decade

Out-of-core nuclear fuel cycle optimization utilizing an engineering workstation

International Nuclear Information System (INIS)

Turinsky, P.J.; Comes, S.A.

1986-01-01

Within the past several years, rapid advances in computer technology have resulted in substantial increases in their performance. The net effect is that problems that could previously only be executed on mainframe computers can now be executed on micro- and minicomputers. The authors are interested in developing an engineering workstation for nuclear fuel management applications. An engineering workstation is defined as a microcomputer with enhanced graphics and communication capabilities. Current fuel management applications range from using workstations as front-end/back-end processors for mainframe computers to completing fuel management scoping calculations. More recently, interest in using workstations for final in-core design calculations has appeared. The authors have used the VAX 11/750 minicomputer, which is not truly an engineering workstation but has comparable performance, to complete both in-core and out-of-core fuel management scoping studies. In this paper, the authors concentrate on our out-of-core research. While much previous work in this area has dealt with decisions concerned with equilibrium cycles, the current project addresses the more realistic situation of nonequilibrium cycles

Workstations studies and radiation protection; Etudes de postes et radioprotection

Energy Technology Data Exchange (ETDEWEB)

Lahaye, T. [Direction des relations du travail, 75 - Paris (France); Donadille, L.; Rehel, J.L.; Paquet, F. [Institut de Radioprotection et de Surete Nucleaire, 92 - Fontenay-aux-Roses (France); Beneli, C. [Paris-5 Univ., 75 (France); Cordoliani, Y.S. [Societe Francaise de Radioprotection, 92 - Fontenay-aux-Roses (France); Vrigneaud, J.M. [Assistance Publique - Hopitaux de Paris, 75 (France); Gauron, C. [Institut National de Recherche et de Securite, 75 - Paris (France); Petrequin, A.; Frison, D. [Association des Medecins du Travail des Salaries du Nucleaire (France); Jeannin, B. [Electricite de France (EDF), 75 - Paris (France); Charles, D. [Polinorsud (France); Carballeda, G. [cabinet Indigo Ergonomie, 33 - Merignac (France); Crouail, P. [Centre d' Etude sur l' Evaluation de la Protection dans le Domaine Nucleaire, 92 - Fontenay-aux-Roses (France); Valot, C. [IMASSA, 91 - Bretigny-sur-Orge (France)

2006-07-01

This day on the workstations studies for the workers follow-up, was organised by the research and health section. Devoted to the company doctors, for the competent persons in radiation protection, for the engineers of safety, it presented examples of methodologies and applications in the medical, industrial domain and the research, so contributing to a better understanding and an application of regulatory measures. The analysis of the workstation has to allow a reduction of the exposures and the risks and lead to the optimization of the medical follow-up. The agenda of this day included the different subjects as follow: evolution of the regulation in matter of demarcation of the regulated zones where the measures of workers protection are strengthened; presentation of the I.R.S.N. guide of help to the realization of a workstation study; implementation of a workstation study: case of radiology; the workstation studies in the research area; Is it necessary to impose the operational dosimetry in the services of radiodiagnostic? The experience feedback of a competent person in radiation protection (P.C.R.) in a hospital environment; radiation protection: elaboration of a good practices guide in medical field; the activities file in nuclear power plant: an evaluation tool of risks for the prevention. Methodological presentation and examples; insulated workstation study; the experience feedback of a provider; Contribution of the ergonomics to the determiners characterization in the ionizing radiation exposure situations;The workstations studies for the internal contamination in the fuel cycle facilities and the consideration of the results in the medical follow-up; R.E.L.I.R. necessity of workstation studies; the consideration of the human factor. (N.C.)

The transition of GTDS to the Unix workstation environment

Science.gov (United States)

Carter, D.; Metzinger, R.; Proulx, R.; Cefola, P.

1995-01-01

Future Flight Dynamics systems should take advantage of the possibilities provided by current and future generations of low-cost, high performance workstation computing environments with Graphical User Interface. The port of the existing mainframe Flight Dynamics systems to the workstation environment offers an economic approach for combining the tremendous engineering heritage that has been encapsulated in these systems with the advantages of the new computing environments. This paper will describe the successful transition of the Draper Laboratory R&D version of GTDS (Goddard Trajectory Determination System) from the IBM Mainframe to the Unix workstation environment. The approach will be a mix of historical timeline notes, descriptions of the technical problems overcome, and descriptions of associated SQA (software quality assurance) issues.

Fast 2D FWI on a multi and many-cores workstation.

Science.gov (United States)

Thierry, Philippe; Donno, Daniela; Noble, Mark

2014-05-01

Following the introduction of x86 co-processors (Xeon Phi) and the performance increase of standard 2-socket workstations using the latest 12 cores E5-v2 x86-64 CPU, we present here a MPI + OpenMP implementation of an acoustic 2D FWI (full waveform inversion) code which simultaneously runs on the CPUs and on the co-processors installed in a workstation. The main advantage of running a 2D FWI on a workstation is to be able to quickly evaluate new features such as more complicated wave equations, new cost functions, finite-difference stencils or boundary conditions. Since the co-processor is made of 61 in-order x86 cores, each of them having up to 4 threads, this many-core can be seen as a shared memory SMP (symmetric multiprocessing) machine with its own IP address. Depending on the vendor, a single workstation can handle several co-processors making the workstation as a personal cluster under the desk. The original Fortran 90 CPU version of the 2D FWI code is just recompiled to get a Xeon Phi x86 binary. This multi and many-core configuration uses standard compilers and associated MPI as well as math libraries under Linux; therefore, the cost of code development remains constant, while improving computation time. We choose to implement the code with the so-called symmetric mode to fully use the capacity of the workstation, but we also evaluate the scalability of the code in native mode (i.e running only on the co-processor) thanks to the Linux ssh and NFS capabilities. Usual care of optimization and SIMD vectorization is used to ensure optimal performances, and to analyze the application performances and bottlenecks on both platforms. The 2D FWI implementation uses finite-difference time-domain forward modeling and a quasi-Newton (with L-BFGS algorithm) optimization scheme for the model parameters update. Parallelization is achieved through standard MPI shot gathers distribution and OpenMP for domain decomposition within the co-processor. Taking advantage of the 16

Experiences with installing and benchmarking SCALE 4.0 on workstations

International Nuclear Information System (INIS)

Montierth, L.M.; Briggs, J.B.

1992-01-01

The advent of economical, high-speed workstations has placed on the criticality engineer's desktop the means to perform computational analysis that was previously possible only on mainframe computers. With this capability comes the need to modify and maintain criticality codes for use on a variety of different workstations. Due to the use of nonstandard coding, compiler differences [in lieu of American National Standards Institute (ANSI) standards], and other machine idiosyncrasies, there is a definite need to systematically test and benchmark all codes ported to workstations. Once benchmarked, a user environment must be maintained to ensure that user code does not become corrupted. The goal in creating a workstation version of the criticality safety analysis sequence (CSAS) codes in SCALE 4.0 was to start with the Cray versions and change as little source code as possible yet produce as generic a code as possible. To date, this code has been ported to the IBM RISC 6000, Data General AViiON 400, Silicon Graphics 4D-35 (all using the same source code), and to the Hewlett Packard Series 700 workstations. The code is maintained under a configuration control procedure. In this paper, the authors address considerations that pertain to the installation and benchmarking of CSAS

Ergonomic guidelines for using notebook personal computers. Technical Committee on Human-Computer Interaction, International Ergonomics Association.

Science.gov (United States)

Saito, S; Piccoli, B; Smith, M J; Sotoyama, M; Sweitzer, G; Villanueva, M B; Yoshitake, R

2000-10-01

In the 1980's, the visual display terminal (VDT) was introduced in workplaces of many countries. Soon thereafter, an upsurge in reported cases of related health problems, such as musculoskeletal disorders and eyestrain, was seen. Recently, the flat panel display or notebook personal computer (PC) became the most remarkable feature in modern workplaces with VDTs and even in homes. A proactive approach must be taken to avert foreseeable ergonomic and occupational health problems from the use of this new technology. Because of its distinct physical and optical characteristics, the ergonomic requirements for notebook PCs in terms of machine layout, workstation design, lighting conditions, among others, should be different from the CRT-based computers. The Japan Ergonomics Society (JES) technical committee came up with a set of guidelines for notebook PC use following exploratory discussions that dwelt on its ergonomic aspects. To keep in stride with this development, the Technical Committee on Human-Computer Interaction under the auspices of the International Ergonomics Association worked towards the international issuance of the guidelines. This paper unveils the result of this collaborative effort.

The image-interpretation-workstation of the future: lessons learned

Science.gov (United States)

Maier, S.; van de Camp, F.; Hafermann, J.; Wagner, B.; Peinsipp-Byma, E.; Beyerer, J.

2017-05-01

In recent years, professionally used workstations got increasingly complex and multi-monitor systems are more and more common. Novel interaction techniques like gesture recognition were developed but used mostly for entertainment and gaming purposes. These human computer interfaces are not yet widely used in professional environments where they could greatly improve the user experience. To approach this problem, we combined existing tools in our imageinterpretation-workstation of the future, a multi-monitor workplace comprised of four screens. Each screen is dedicated to a special task in the image interpreting process: a geo-information system to geo-reference the images and provide a spatial reference for the user, an interactive recognition support tool, an annotation tool and a reporting tool. To further support the complex task of image interpreting, self-developed interaction systems for head-pose estimation and hand tracking were used in addition to more common technologies like touchscreens, face identification and speech recognition. A set of experiments were conducted to evaluate the usability of the different interaction systems. Two typical extensive tasks of image interpreting were devised and approved by military personal. They were then tested with a current setup of an image interpreting workstation using only keyboard and mouse against our image-interpretationworkstation of the future. To get a more detailed look at the usefulness of the interaction techniques in a multi-monitorsetup, the hand tracking, head pose estimation and the face recognition were further evaluated using tests inspired by everyday tasks. The results of the evaluation and the discussion are presented in this paper.

Physics and detector simulation facility Type O workstation specifications

International Nuclear Information System (INIS)

Chartrand, G.; Cormell, L.R.; Hahn, R.; Jacobson, D.; Johnstad, H.; Leibold, P.; Marquez, M.; Ramsey, B.; Roberts, L.; Scipioni, B.; Yost, G.P.

1990-11-01

This document specifies the requirements for the front-end network of workstations of a distributed computing facility. This facility will be needed to perform the physics and detector simulations for the design of Superconducting Super Collider (SSC) detectors, and other computations in support of physics and detector needs. A detailed description of the computer simulation facility is given in the overall system specification document. This document provides revised subsystem specifications for the network of monitor-less Type 0 workstations. The requirements specified in this document supersede the requirements given. In Section 2 a brief functional description of the facility and its use are provided. The list of detailed specifications (vendor requirements) is given in Section 3 and the qualifying requirements (benchmarks) are described in Section 4

The microcomputer workstation - An alternate hardware architecture for remotely sensed image analysis

Science.gov (United States)

Erickson, W. K.; Hofman, L. B.; Donovan, W. E.

1984-01-01

Difficulties regarding the digital image analysis of remotely sensed imagery can arise in connection with the extensive calculations required. In the past, an expensive large to medium mainframe computer system was needed for performing these calculations. For image-processing applications smaller minicomputer-based systems are now used by many organizations. The costs for such systems are still in the range from $100K to $300K. Recently, as a result of new developments, the use of low-cost microcomputers for image processing and display systems appeared to have become feasible. These developments are related to the advent of the 16-bit microprocessor and the concept of the microcomputer workstation. Earlier 8-bit microcomputer-based image processing systems are briefly examined, and a computer workstation architecture is discussed. Attention is given to a microcomputer workstation developed by Stanford University, and the design and implementation of a workstation network.

Computer-aided diagnosis workstation and database system for chest diagnosis based on multi-helical CT images

Science.gov (United States)

Satoh, Hitoshi; Niki, Noboru; Mori, Kiyoshi; Eguchi, Kenji; Kaneko, Masahiro; Kakinuma, Ryutarou; Moriyama, Noriyuki; Ohmatsu, Hironobu; Masuda, Hideo; Machida, Suguru; Sasagawa, Michizou

2006-03-01

Multi-helical CT scanner advanced remarkably at the speed at which the chest CT images were acquired for mass screening. Mass screening based on multi-helical CT images requires a considerable number of images to be read. It is this time-consuming step that makes the use of helical CT for mass screening impractical at present. To overcome this problem, we have provided diagnostic assistance methods to medical screening specialists by developing a lung cancer screening algorithm that automatically detects suspected lung cancers in helical CT images and a coronary artery calcification screening algorithm that automatically detects suspected coronary artery calcification. We also have developed electronic medical recording system and prototype internet system for the community health in two or more regions by using the Virtual Private Network router and Biometric fingerprint authentication system and Biometric face authentication system for safety of medical information. Based on these diagnostic assistance methods, we have now developed a new computer-aided workstation and database that can display suspected lesions three-dimensionally in a short time. This paper describes basic studies that have been conducted to evaluate this new system. The results of this study indicate that our computer-aided diagnosis workstation and network system can increase diagnostic speed, diagnostic accuracy and safety of medical information.

System engineering workstations - critical tool in addressing waste storage, transportation, or disposal

International Nuclear Information System (INIS)

Mar, B.W.

1987-01-01

The ability to create, evaluate, operate, and manage waste storage, transportation, and disposal systems (WSTDSs) is greatly enhanced when automated tools are available to support the generation of the voluminous mass of documents and data associated with the system engineering of the program. A system engineering workstation is an optimized set of hardware and software that provides such automated tools to those performing system engineering functions. This paper explores the functions that need to be performed by a WSTDS system engineering workstation. While the latter stages of a major WSTDS may require a mainframe computer and specialized software systems, most of the required system engineering functions can be supported by a system engineering workstation consisting of a personnel computer and commercial software. These findings suggest system engineering workstations for WSTDS applications will cost less than $5000 per unit, and the payback on the investment can be realized in a few months. In most cases the major cost element is not the capital costs of hardware or software, but the cost to train or retrain the system engineers in the use of the workstation and to ensure that the system engineering functions are properly conducted

Supervisory Control Technique For An Assembly Workstation As A Dynamic Discrete Event System

Directory of Open Access Journals (Sweden)

Daniela Cristina CERNEGA

2001-12-01

Full Text Available This paper proposes a control problem statement in the framework of supervisory control technique for the assembly workstations. A desired behaviour of an assembly workstation is analysed. The behaviour of such a workstation is cyclic and some linguistic properties are established. In this paper, it is proposed an algorithm for the computation of the supremal controllable language of the closed system desired language. Copyright © 2001 IFAC.

VMware workstation

CERN Document Server

van Vugt, Sander

2013-01-01

This book is a practical, step-by-step guide to creating and managing virtual machines using VMware Workstation.VMware Workstation: No Experience Necessary is for developers as well as system administrators who want to efficiently set up a test environment .You should have basic networking knowledge, and prior experience with Virtual Machines and VMware Player would be beneficial

How users organize electronic files on their workstations in the office environment: a preliminary study of personal information organization behaviour

Directory of Open Access Journals (Sweden)

Christopher S.G. Khoo

2007-01-01

Full Text Available An ongoing study of how people organize their computer files and folders on the hard disk of their office workstations. A questionnaire was used to collect information on the subjects, their work responsibilities and characteristics of their workstations. Data on file and folder names and file structure were extracted from the hard disk using a computer program STG FolderPrint Plus, DOS command and screen capture. A semi-structured interview collected information on subjects' strategies in naming and organizing files and folders, and in locating and retrieving files. The data were analysed mainly through qualitative analysis and content analysis. The subjects organized their folders in a variety of structures, from broad and shallow to narrow and deep hierarchies. One to three levels of folders is common. The labels for first level folders tended to be task-based or project-based. Most subjects located files by browsing the folder structure, with searching used as a last resort. The most common types of folder names were document type, organizational function or structure, and miscellaneous or temporary. The frequency of folders of different types appear related to the type of occupation.

Computer ray tracing speeds.

Science.gov (United States)

Robb, P; Pawlowski, B

1990-05-01

The results of measuring the ray trace speed and compilation speed of thirty-nine computers in fifty-seven configurations, ranging from personal computers to super computers, are described. A correlation of ray trace speed has been made with the LINPACK benchmark which allows the ray trace speed to be estimated using LINPACK performance data. The results indicate that the latest generation of workstations, using CPUs based on RISC (Reduced Instruction Set Computer) technology, are as fast or faster than mainframe computers in compute-bound situations.

NET remote workstation

International Nuclear Information System (INIS)

Leinemann, K.

1990-10-01

The goal of this NET study was to define the functionality of a remote handling workstation and its hardware and software architecture. The remote handling workstation has to fulfill two basic functions: (1) to provide the man-machine interface (MMI), that means the interface to the control system of the maintenance equipment and to the working environment (telepresence) and (2) to provide high level (task level) supporting functions (software tools) during the maintenance work and in the preparation phase. Concerning the man-machine interface, an important module of the remote handling workstation besides the standard components of man-machine interfacing is a module for graphical scene presentation supplementing viewing by TV. The technique of integrated viewing is well known from JET BOOM and TARM control using the GBsim and KISMET software. For integration of equipment dependent MMI functions the remote handling workstation provides a special software module interface. Task level support of the operator is based on (1) spatial (geometric/kinematic) models, (2) remote handling procedure models, and (3) functional models of the equipment. These models and the related simulation modules are used for planning, programming, execution monitoring, and training. The workstation provides an intelligent handbook guiding the operator through planned procedures illustrated by animated graphical sequences. For unplanned situations decision aids are available. A central point of the architectural design was to guarantee a high flexibility with respect to hardware and software. Therefore the remote handling workstation is designed as an open system based on widely accepted standards allowing the stepwise integration of the various modules starting with the basic MMI and the spatial simulation as standard components. (orig./HP) [de

Impact of workstations on criticality analyses at ABB combustion engineering

International Nuclear Information System (INIS)

Tarko, L.B.; Freeman, R.S.; O'Donnell, P.F.

1993-01-01

During 1991, ABB Combustion Engineering (ABB C-E) made the transition from a CDC Cyber 990 mainframe for nuclear criticality safety analyses to Hewlett Packard (HP)/Apollo workstations. The primary motivation for this change was improved economics of the workstation and maintaining state-of-the-art technology. The Cyber 990 utilized the NOS operating system with a 60-bit word size. The CPU memory size was limited to 131 100 words of directly addressable memory with an extended 250000 words available. The Apollo workstation environment at ABB consists of HP/Apollo-9000/400 series desktop units used by most application engineers, networked with HP/Apollo DN10000 platforms that use 32-bit word size and function as the computer servers and network administrative CPUS, providing a virtual memory system

Criticality codes migration to workstations at the Hanford site

International Nuclear Information System (INIS)

Miller, E.M.

1993-01-01

Westinghouse Hanford Company, Hanford Site Operations contractor, Richland, Washington, currently runs criticality codes on the Cray X-MP EA/232 computer but has recommended that US Department of Energy DOE-Richland replace the Cray with more economical workstations

Engineering workstation: Sensor modeling

Science.gov (United States)

Pavel, M; Sweet, B.

1993-01-01

The purpose of the engineering workstation is to provide an environment for rapid prototyping and evaluation of fusion and image processing algorithms. Ideally, the algorithms are designed to optimize the extraction of information that is useful to a pilot for all phases of flight operations. Successful design of effective fusion algorithms depends on the ability to characterize both the information available from the sensors and the information useful to a pilot. The workstation is comprised of subsystems for simulation of sensor-generated images, image processing, image enhancement, and fusion algorithms. As such, the workstation can be used to implement and evaluate both short-term solutions and long-term solutions. The short-term solutions are being developed to enhance a pilot's situational awareness by providing information in addition to his direct vision. The long term solutions are aimed at the development of complete synthetic vision systems. One of the important functions of the engineering workstation is to simulate the images that would be generated by the sensors. The simulation system is designed to use the graphics modeling and rendering capabilities of various workstations manufactured by Silicon Graphics Inc. The workstation simulates various aspects of the sensor-generated images arising from phenomenology of the sensors. In addition, the workstation can be used to simulate a variety of impairments due to mechanical limitations of the sensor placement and due to the motion of the airplane. Although the simulation is currently not performed in real-time, sequences of individual frames can be processed, stored, and recorded in a video format. In that way, it is possible to examine the appearance of different dynamic sensor-generated and fused images.

Selecting Personal Computers.

Science.gov (United States)

Djang, Philipp A.

1993-01-01

Describes a Multiple Criteria Decision Analysis Approach for the selection of personal computers that combines the capabilities of Analytic Hierarchy Process and Integer Goal Programing. An example of how decision makers can use this approach to determine what kind of personal computers and how many of each type to purchase is given. (nine…

Users Guide to VSMOKE-GIS for Workstations

Science.gov (United States)

Mary F. Harms; Leonidas G. Lavdas

1997-01-01

VSMOKE-GIS was developed to help prescribed burners in the national forests of the Southeastern United States visualize smoke dispersion and to plan prescribed burns. Developed for use on workstations, this decision-support system consists of a graphical user interface, written in Arc/Info Arc Macro Language, and is linked to a FORTRAN computer program. VSMOKE-GIS...

Initial experience with a nuclear medicine viewing workstation

Science.gov (United States)

Witt, Robert M.; Burt, Robert W.

1992-07-01

Graphical User Interfaced (GUI) workstations are now available from commercial vendors. We recently installed a GUI workstation in our nuclear medicine reading room for exclusive use of staff and resident physicians. The system is built upon a Macintosh platform and has been available as a DELTAmanager from MedImage and more recently as an ICON V from Siemens Medical Systems. The workstation provides only display functions and connects to our existing nuclear medicine imaging system via ethernet. The system has some processing capabilities to create oblique, sagittal and coronal views from transverse tomographic views. Hard copy output is via a screen save device and a thermal color printer. The DELTAmanager replaced a MicroDELTA workstation which had both process and view functions. The mouse activated GUI has made remarkable changes to physicians'' use of the nuclear medicine viewing system. Training time to view and review studies has been reduced from hours to about 30-minutes. Generation of oblique views and display of brain and heart tomographic studies has been reduced from about 30-minutes of technician''s time to about 5-minutes of physician''s time. Overall operator functionality has been increased so that resident physicians with little prior computer experience can access all images on the image server and display pertinent patient images when consulting with other staff.

The integrated workstation: A common, consistent link between nuclear plant personnel and plant information and computerized resources

International Nuclear Information System (INIS)

Wood, R.T.; Knee, H.E.; Mullens, J.A.; Munro, J.K. Jr.; Swail, B.K.; Tapp, P.A.

1993-01-01

The increasing use of computer technology in the US nuclear power industry has greatly expanded the capability to obtain, analyze, and present data about the plant to station personnel. Data concerning a power plant's design, configuration, operational and maintenance histories, and current status, and the information that can be derived from them, provide the link between the plant and plant staff. It is through this information bridge that operations, maintenance and engineering personnel understand and manage plant performance. However, it is necessary to transform the vast quantity of data available from various computer systems and across communications networks into clear, concise, and coherent information. In addition, it is important to organize this information into a consolidated, structured form within an integrated environment so that various users throughout the plant have ready access at their local station to knowledge necessary for their tasks. Thus, integrated workstations are needed to provide the inquired information and proper software tools, in a manner that can be easily understood and used, to the proper users throughout the plant. An effort is underway at the Oak Ridge National Laboratory to address this need by developing Integrated Workstation functional requirements and implementing a limited-scale prototype demonstration. The integrated Workstation requirements will define a flexible, expandable computer environment that permits a tailored implementation of workstation capabilities and facilitates future upgrades to add enhanced applications. The functionality to be supported by the integrated workstation and inherent capabilities to be provided by the workstation environment win be described. In addition, general technology areas which are to be addressed in the Integrated Workstation functional requirements will be discussed

Nuclear plant analyzer desktop workstation

International Nuclear Information System (INIS)

Beelman, R.J.

1990-01-01

In 1983 the U.S. Nuclear Regulatory Commission (USNRC) commissioned the Idaho National Engineering Laboratory (INEL) to develop a Nuclear Plant Analyzer (NPA). The NPA was envisioned as a graphical aid to assist reactor safety analysts in comprehending the results of thermal-hydraulic code calculations. The development was to proceed in three distinct phases culminating in a desktop reactor safety workstation. The desktop NPA is now complete. The desktop NPA is a microcomputer based reactor transient simulation, visualization and analysis tool developed at INEL to assist an analyst in evaluating the transient behavior of nuclear power plants by means of graphic displays. The NPA desktop workstation integrates advanced reactor simulation codes with online computer graphics allowing reactor plant transient simulation and graphical presentation of results. The graphics software, written exclusively in ANSI standard C and FORTRAN 77 and implemented over the UNIX/X-windows operating environment, is modular and is designed to interface to the NRC's suite of advanced thermal-hydraulic codes to the extent allowed by that code. Currently, full, interactive, desktop NPA capabilities are realized only with RELAP5

Computer modeling and design of diagnostic workstations and radiology reading rooms

Science.gov (United States)

Ratib, Osman M.; Amato, Carlos L.; Balbona, Joseph A.; Boots, Kevin; Valentino, Daniel J.

2000-05-01

We used 3D modeling techniques to design and evaluate the ergonomics of diagnostic workstation and radiology reading room in the planning phase of building a new hospital at UCLA. Given serious space limitations, the challenge was to provide more optimal working environment for radiologists in a crowded and busy environment. A particular attention was given to flexibility, lighting condition and noise reduction in rooms shared by multiple users performing diagnostic tasks as well as regular clinical conferences. Re-engineering workspace ergonomics rely on the integration of new technologies, custom designed cabinets, indirect lighting, sound-absorbent partitioning and geometric arrangement of workstations to allow better privacy while optimizing space occupation. Innovations included adjustable flat monitors, integration of videoconferencing and voice recognition, control monitor and retractable keyboard for optimal space utilization. An overhead compartment protecting the monitors from ambient light is also used as accessory lightbox and rear-view projection screen for conferences.

Concurrent use of data base and graphics computer workstations to provide graphic access to large, complex data bases for robotics control of nuclear surveillance and maintenance

International Nuclear Information System (INIS)

Dalton, G.R.; Tulenko, J.S.; Zhou, X.

1990-01-01

The University of Florida is part of a multiuniversity research effort, sponsored by the US Department of Energy which is under way to develop and deploy an advanced semi-autonomous robotic system for use in nuclear power stations. This paper reports on the development of the computer tools necessary to gain convenient graphic access to the intelligence implicit in a large complex data base such as that in a nuclear reactor plant. This program is integrated as a man/machine interface within the larger context of the total computerized robotic planning and control system. The portion of the project described here addresses the connection between the three-dimensional displays on an interactive graphic workstation and a data-base computer running a large data-base server program. Programming the two computers to work together to accept graphic queries and return answers on the graphic workstation is a key part of the interactive capability developed

Computer based workstation for development of software for high energy physics experiments

International Nuclear Information System (INIS)

Ivanchenko, I.M.; Sedykh, Yu.V.

1987-01-01

Methodical principles and results of a successful attempt to create on the base of IBM-PC/AT personal computer of effective means for development of programs for high energy physics experiments are analysed. The obtained results permit to combine the best properties and a positive materialized experience accumulated on the existing time sharing collective systems with a high quality of data representation, reliability and convenience of personal computer applications

Generalization of Posture Training to Computer Workstations in an Applied Setting

Science.gov (United States)

Sigurdsson, Sigurdur O.; Ring, Brandon M.; Needham, Mick; Boscoe, James H.; Silverman, Kenneth

2011-01-01

Improving employees' posture may decrease the risk of musculoskeletal disorders. The current paper is a systematic replication and extension of Sigurdsson and Austin (2008), who found that an intervention consisting of information, real-time feedback, and self-monitoring improved participant posture at mock workstations. In the current study,…

Piping stress analysis with personal computers

International Nuclear Information System (INIS)

Revesz, Z.

1987-01-01

The growing market of the personal computers is providing an increasing number of professionals with unprecedented and surprisingly inexpensive computing capacity, which if using with powerful software, can enhance immensely the engineers capabilities. This paper focuses on the possibilities which opened in piping stress analysis by the widespread distribution of personal computers, on the necessary changes in the software and on the limitations of using personal computers for engineering design and analysis. Reliability and quality assurance aspects of using personal computers for nuclear applications are also mentioned. The paper resumes with personal views of the author and experiences gained during interactive graphic piping software development for personal computers. (orig./GL)

Real-time monitoring/emergency response modeling workstation for a tritium facility

International Nuclear Information System (INIS)

Lawver, B.S.; Sims, J.M.; Baskett, R.L.

1993-01-01

At Lawrence Livermore National Laboratory (LLNL) we have developed a real-time system to monitor two stacks on our tritium handling facility. The monitors transmit the stack data to a workstation, which computes a three-dimensional numerical model of atmospheric dispersion. The workstation also collects surface and upper air data from meteorological towers and a sodar. The complex meteorological and terrain setting in the Livermore Valley demands more sophisticated resolution of the three-dimensional structure of the atmosphere to reliably calculate plume dispersion than afforded by Gaussian models. We experience both mountain valley and sea breeze flows. To address these complexities, we have implemented the three-dimensional diagnostic MATHEW mass-adjusted wind field and ADPIC particle-in-cell dispersion models on the workstation for use in real-time emergency response modeling. Both MATHEW and ADPIC have shown their utility in a variety of complex settings over the last 15 yr within the U.S. Department of Energy's Atmospheric Release Advisory Capability (ARAC) project. Faster workstations and real-time instruments allow utilization of more complex three-dimensional models, which provides a foundation for building a real-time monitoring and emergency response workstation for a tritium facility. The stack monitors are two ion chambers per stack

A methodology to emulate and evaluate a productive virtual workstation

Science.gov (United States)

Krubsack, David; Haberman, David

1992-01-01

The Advanced Display and Computer Augmented Control (ADCACS) Program at ACT is sponsored by NASA Ames to investigate the broad field of technologies which must be combined to design a 'virtual' workstation for the Space Station Freedom. This program is progressing in several areas and resulted in the definition of requirements for a workstation. A unique combination of technologies at the ACT Laboratory have been networked to effectively create an experimental environment. This experimental environment allows the integration of nonconventional input devices with a high power graphics engine within the framework of an expert system shell which coordinates the heterogeneous inputs with the 'virtual' presentation. The flexibility of the workstation is evolved as experiments are designed and conducted to evaluate the condition descriptions and rule sets of the expert system shell and its effectiveness in driving the graphics engine. Workstation productivity has been defined by the achievable performance in the emulator of the calibrated 'sensitivity' of input devices, the graphics presentation, the possible optical enhancements to achieve a wide field of view color image and the flexibility of conditional descriptions in the expert system shell in adapting to prototype problems.

On the Use of Computers for Teaching Fluid Mechanics

Science.gov (United States)

Benson, Thomas J.

1994-01-01

Several approaches for improving the teaching of basic fluid mechanics using computers are presented. There are two objectives to these approaches: to increase the involvement of the student in the learning process and to present information to the student in a variety of forms. Items discussed include: the preparation of educational videos using the results of computational fluid dynamics (CFD) calculations, the analysis of CFD flow solutions using workstation based post-processing graphics packages, and the development of workstation or personal computer based simulators which behave like desk top wind tunnels. Examples of these approaches are presented along with observations from working with undergraduate co-ops. Possible problems in the implementation of these approaches as well as solutions to these problems are also discussed.

Computer-aided diagnosis workstation and data base system for chest diagnosis based on multihelical CT images

International Nuclear Information System (INIS)

Satoh, H.; Niki, N.; Eguchi, K.; Masuda, H.; Machida, S.; Moriyama, N.

2006-01-01

We have provided diagnostic assistance methods to medical screening specialists by developing a lung cancer screening algorithm that automatically detects suspected lung cancers in helical CT images and a coronary artery calcification screening algorithm that automatically detects suspected coronary artery calcification. We also have developed electronic medical recording system and prototype internet system for the community health in two or more regions by using the Virtual Private Network router, Biometric fingerprint authentication system and Biometric face authentication system for safety of medical information. The results of this study indicate that our computer-aided diagnosis workstation and network system can increase diagnostic speed, diagnostic accuracy and safety of medical information. (author)

A PC [personal computer]-based version of KENO V.a

International Nuclear Information System (INIS)

Nigg, D.A.; Atkinson, C.A.; Briggs, J.B.; Taylor, J.T.

1990-01-01

The use of personal computers (PCs) and engineering workstations for complex scientific computations has expanded rapidly in the last few years. This trend is expected to continue in the future with the introduction of increasingly sophisticated microprocessors and microcomputer systems. For a number of reasons, including security, economy, user convenience, and productivity, an integrated system of neutronics and radiation transport software suitable for operation in an IBM PC-class environment has been under development at the Idaho National Engineering Laboratory (INEL) for the past 3 yr. Nuclear cross-section data and resonance parameters are preprocessed from the Evaluated Nuclear Data Files Version 5 (ENDF/B-V) and supplied in a form suitable for use in a PC-based spectrum calculation and multigroup cross-section generation module. This module produces application-specific data libraries that can then be used in various neutron transport and diffusion theory code modules. This paper discusses several details of the Monte Carlo criticality module, which is based on the well-known highly-sophisticated KENO V.a package developed at Oak Ridge National Laboratory and previously released in mainframe form by the Radiation Shielding Information Center (RSIC). The conversion process and a variety of benchmarking results are described

Graphics metafile interface to ARAC emergency response models for remote workstation study

International Nuclear Information System (INIS)

Lawver, B.S.

1985-01-01

The Department of Energy's Atmospheric Response Advisory Capability models are executed on computers at a central computer center with the output distributed to accident advisors in the field. The output of these atmospheric diffusion models are generated as contoured isopleths of concentrations. When these isopleths are overlayed with local geography, they become a useful tool to the accident site advisor. ARAC has developed a workstation that is located at potential accident sites. The workstation allows the accident advisor to view color plots of the model results, scale those plots and print black and white hardcopy of the model results. The graphics metafile, also known as Virtual Device Metafile (VDM) allows the models to generate a single device independent output file that is partitioned into geography, isoopleths and labeling information. The metafile is a very compact data storage technique that is output device independent. The metafile frees the model from either generating output for all known graphic devices or requiring the model to be rerun for additional graphic devices. With the partitioned metafile ARAC can transmit to the remote workstation the isopleths and labeling for each model. The geography database may not change and can be transmitted only when needed. This paper describes the important features of the remote workstation and how these features are supported by the device independent graphics metafile

Treadmill workstations: the effects of walking while working on physical activity and work performance.

Directory of Open Access Journals (Sweden)

Avner Ben-Ner

Full Text Available We conducted a 12-month-long experiment in a financial services company to study how the availability of treadmill workstations affects employees' physical activity and work performance. We enlisted sedentary volunteers, half of whom received treadmill workstations during the first two months of the study and the rest in the seventh month of the study. Participants could operate the treadmills at speeds of 0-2 mph and could use a standard chair-desk arrangement at will. (a Weekly online performance surveys were administered to participants and their supervisors, as well as to all other sedentary employees and their supervisors. Using within-person statistical analyses, we find that overall work performance, quality and quantity of performance, and interactions with coworkers improved as a result of adoption of treadmill workstations. (b Participants were outfitted with accelerometers at the start of the study. We find that daily total physical activity increased as a result of the adoption of treadmill workstations.

Treadmill workstations: the effects of walking while working on physical activity and work performance.

Science.gov (United States)

Ben-Ner, Avner; Hamann, Darla J; Koepp, Gabriel; Manohar, Chimnay U; Levine, James

2014-01-01

We conducted a 12-month-long experiment in a financial services company to study how the availability of treadmill workstations affects employees' physical activity and work performance. We enlisted sedentary volunteers, half of whom received treadmill workstations during the first two months of the study and the rest in the seventh month of the study. Participants could operate the treadmills at speeds of 0-2 mph and could use a standard chair-desk arrangement at will. (a) Weekly online performance surveys were administered to participants and their supervisors, as well as to all other sedentary employees and their supervisors. Using within-person statistical analyses, we find that overall work performance, quality and quantity of performance, and interactions with coworkers improved as a result of adoption of treadmill workstations. (b) Participants were outfitted with accelerometers at the start of the study. We find that daily total physical activity increased as a result of the adoption of treadmill workstations.

Using Computers in Fluids Engineering Education

Science.gov (United States)

Benson, Thomas J.

1998-01-01

Three approaches for using computers to improve basic fluids engineering education are presented. The use of computational fluid dynamics solutions to fundamental flow problems is discussed. The use of interactive, highly graphical software which operates on either a modern workstation or personal computer is highlighted. And finally, the development of 'textbooks' and teaching aids which are used and distributed on the World Wide Web is described. Arguments for and against this technology as applied to undergraduate education are also discussed.

Ruling Out Brain CT Contraindications prior to Intravenous Thrombolysis: Diagnostic Equivalence between a Primary Interpretation Workstation and a Mobile Tablet Computer

Directory of Open Access Journals (Sweden)

Antonio J. Salazar

2017-01-01

Full Text Available Objective. The aim of this study was to evaluate the equivalence of brain CT interpretations performed using a diagnostic workstation and a mobile tablet computer, in a telestroke service. Materials and Methods. The ethics committee of our institution approved this retrospective study. A factorial design with 1452 interpretations was used. The assessed variables were the type of stroke classification, the presence of contraindications to the tPA administration, the presence of a hyperdense intracranial artery sign (HMCA, and the Alberta Stroke Program Early CT Score (ASPECTS score. These variables were evaluated to determine the effect that the reading system had on their magnitudes. Results. The achieved distribution of observed lesions using both the reading systems was not statistically different. The differences between the two reading systems to claim equivalence were 1.6% for hemorrhagic lesions, 4.5% for cases without lesion, and 5.2 for overall ischemic lesion. Equivalence was achieved at 2.1% for ASPECTS ≤ 6, 6.5% for the presence of imaging contraindication to the tPA administration, and 7.2% for the presence of HMCA. Conclusion. The diagnostic performance for detecting acute stroke is likely equivalent whether a tablet computer or a diagnostic workstation is used or not.

Experience in using workstations as hosts in an accelerator control environment

International Nuclear Information System (INIS)

Abola, A.; Casella, R.; Clifford, T.; Hoff, L.; Katz, R.; Kennell, S.; Mandell, S.; McBreen, E.; Weygand, D.P.

1987-03-01

A new control system has been used for light ion acceleration at the Alternating Gradient Synchrotron (AGS). The control system uses Apollo workstations in the dual role of console hardware computer and controls system host. It has been found that having a powerful dedicated CPU with a demand paging virtual memory OS featuring strong interprocess communication, mapped memory shared files, shared code, and multi-window capabilities, allows us to provide an efficient operation environment in which users may view and manage several control processes simultaneously. The same features which make workstations good console computers also provide an outstanding platform for code development. The software for the system, consisting of about 30K lines of ''C'' code, was developed on schedule, ready for light ion commissioning. System development is continuing with work being done on applications programs

Experience in using workstations as hosts in an accelerator control environment

International Nuclear Information System (INIS)

Abola, A.; Casella, R.; Clifford, T.; Hoff, L.; Katz, R.; Kennell, S.; Mandell, S.; McBreen, E.; Weygand, D.P.

1987-01-01

A new control system has been used for light ion acceleration at the Alternating Gradient Synchrotron (AGS). The control system uses Apollo workstations in the dual role of console hardware computer and controls system host. It has been found that having a powerful dedicated CPU with a demand paging virtual memory OS featuring strong interprocess communication, mapped memory shared files, shared code, and multi-window capabilities, allows us to provide an efficient operation environment in which users may view and manage several control processes simultaneously. The same features which make workstations good console computers also provide an outstanding platform for code development. The software for the system, consisting of about 30K lines of ''C'' code, was developed on schedule, ready for light ion commissioning. System development is continuing with work being done on applications programs

Clinical impact and value of workstation single sign-on.

Science.gov (United States)

Gellert, George A; Crouch, John F; Gibson, Lynn A; Conklin, George S; Webster, S Luke; Gillean, John A

2017-05-01

CHRISTUS Health began implementation of computer workstation single sign-on (SSO) in 2015. SSO technology utilizes a badge reader placed at each workstation where clinicians swipe or "tap" their identification badges. To assess the impact of SSO implementation in reducing clinician time logging in to various clinical software programs, and in financial savings from migrating to a thin client that enabled replacement of traditional hard drive computer workstations. Following implementation of SSO, a total of 65,202 logins were sampled systematically during a 7day period among 2256 active clinical end users for time saved in 6 facilities when compared to pre-implementation. Dollar values were assigned to the time saved by 3 groups of clinical end users: physicians, nurses and ancillary service providers. The reduction of total clinician login time over the 7day period showed a net gain of 168.3h per week of clinician time - 28.1h (2.3 shifts) per facility per week. Annualized, 1461.2h of mixed physician and nursing time is liberated per facility per annum (121.8 shifts of 12h per year). The annual dollar cost savings of this reduction of time expended logging in is $92,146 per hospital per annum and $1,658,745 per annum in the first phase implementation of 18 hospitals. Computer hardware equipment savings due to desktop virtualization increases annual savings to $2,333,745. Qualitative value contributions to clinician satisfaction, reduction in staff turnover, facilitation of adoption of EHR applications, and other benefits of SSO are discussed. SSO had a positive impact on clinician efficiency and productivity in the 6 hospitals evaluated, and is an effective and cost-effective method to liberate clinician time from repetitive and time consuming logins to clinical software applications. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

A worldwide flock of Condors : load sharing among workstation clusters

NARCIS (Netherlands)

Epema, D.H.J.; Livny, M.; Dantzig, van R.; Evers, X.; Pruyne, J.

1996-01-01

Condor is a distributed batch system for sharing the workload of compute-intensive jobs in a pool of unix workstations connected by a network. In such a Condor pool, idle machines are spotted by Condor and allocated to queued jobs, thus putting otherwise unutilized capacity to efficient use. When

Advanced Satellite Workstation - An integrated workstation environment for operational support of satellite system planning and analysis

Science.gov (United States)

Hamilton, Marvin J.; Sutton, Stewart A.

A prototype integrated environment, the Advanced Satellite Workstation (ASW), which was developed and delivered for evaluation and operator feedback in an operational satellite control center, is described. The current ASW hardware consists of a Sun Workstation and Macintosh II Workstation connected via an ethernet Network Hardware and Software, Laser Disk System, Optical Storage System, and Telemetry Data File Interface. The central objective of ASW is to provide an intelligent decision support and training environment for operator/analysis of complex systems such as satellites. Compared to the many recent workstation implementations that incorporate graphical telemetry displays and expert systems, ASW provides a considerably broader look at intelligent, integrated environments for decision support, based on the premise that the central features of such an environment are intelligent data access and integrated toolsets.

VAX Professional Workstation goes graphic

International Nuclear Information System (INIS)

Downward, J.G.

1984-01-01

The VAX Professional Workstation (VPW) is a collection of programs and procedures designed to provide an integrated work-station environment for the staff at KMS Fusion's research laboratories. During the past year numerous capabilities have been added to VPW, including support for VT125/VT240/4014 graphic workstations, editing windows, and additional desk utilities. Graphics workstation support allows users to create, edit, and modify graph data files, enter the data via a graphic tablet, create simple plots with DATATRIEVE or DECgraph on ReGIS terminals, or elaborate plots with TEKGRAPH on ReGIS or Tektronix terminals. Users may assign display error bars to the data and interactively plot it in a variety of ways. Users also can create and display viewgraphs. Hard copy output for a large network of office terminals is obtained by multiplexing each terminal's video output into a recently developed video multiplexer front ending a single channel video hard copy unit

User interface on networked workstations for MFTF plasma diagnostic instruments

International Nuclear Information System (INIS)

Renbarger, V.L.; Balch, T.R.

1985-01-01

A network of Sun-2/170 workstations is used to provide an interface to the MFTF-B Plasma Diagnostics System at Lawrence Livermore National Laboratory. The Plasma Diagnostics System (PDS) is responsible for control of MFTF-B plasma diagnostic instrumentation. An EtherNet Local Area Network links the workstations to a central multiprocessing system which furnishes data processing, data storage and control services for PDS. These workstations permit a physicist to command data acquisition, data processing, instrument control, and display of results. The interface is implemented as a metaphorical desktop, which helps the operator form a mental model of how the system works. As on a real desktop, functions are provided by sheets of paper (windows on a CRT screen) called worksheets. The worksheets may be invoked by pop-up menus and may be manipulated with a mouse. These worksheets are actually tasks that communicate with other tasks running in the central computer system. By making entries in the appropriate worksheet, a physicist may specify data acquisition or processing, control a diagnostic, or view a result

Personal Computers.

Science.gov (United States)

Toong, Hoo-min D.; Gupta, Amar

1982-01-01

Describes the hardware, software, applications, and current proliferation of personal computers (microcomputers). Includes discussions of microprocessors, memory, output (including printers), application programs, the microcomputer industry, and major microcomputer manufacturers (Apple, Radio Shack, Commodore, and IBM). (JN)

Integrating UNIX workstation into existing online data acquisition systems for Fermilab experiments

International Nuclear Information System (INIS)

Oleynik, G.

1991-03-01

With the availability of cost effective computing prior from multiple vendors of UNIX workstations, experiments at Fermilab are adding such computers to their VMS based online data acquisition systems. In anticipation of this trend, we have extended the software products available in our widely used VAXONLINE and PANDA data acquisition software systems, to provide support for integrating these workstations into existing distributed online systems. The software packages we are providing pave the way for the smooth migration of applications from the current Data Acquisition Host and Monitoring computers running the VMS operating systems, to UNIX based computers of various flavors. We report on software for Online Event Distribution from VAXONLINE and PANDA, integration of Message Reporting Facilities, and a framework under UNIX for experiments to monitor and view the raw event data produced at any level in their DA system. We have developed software that allows host UNIX computers to communicate with intelligent front-end embedded read-out controllers and processor boards running the pSOS operating system. Both RS-232 and Ethernet control paths are supported. This enables calibration and hardware monitoring applications to be migrated to these platforms. 6 refs., 5 figs

Ensemble computing for the petroleum industry

International Nuclear Information System (INIS)

Annaratone, M.; Dossa, D.

1995-01-01

Computer downsizing is one of the most often used buzzwords in today's competitive business, and the petroleum industry is at the forefront of this revolution. Ensemble computing provides the key for computer downsizing with its first incarnation, i.e., workstation farms. This paper concerns the importance of increasing the productivity cycle and not just the execution time of a job. The authors introduce the concept of ensemble computing and workstation farms. The they discuss how different computing paradigms can be addressed by workstation farms

Use of the stereoscopic virtual reality display system for the detection and characterization of intracranial aneurysms: A Icomparison with conventional computed tomography workstation and 3D rotational angiography.

Science.gov (United States)

Liu, Xiujuan; Tao, Haiquan; Xiao, Xigang; Guo, Binbin; Xu, Shangcai; Sun, Na; Li, Maotong; Xie, Li; Wu, Changjun

2018-07-01

This study aimed to compare the diagnostic performance of the stereoscopic virtual reality display system with the conventional computed tomography (CT) workstation and three-dimensional rotational angiography (3DRA) for intracranial aneurysm detection and characterization, with a focus on small aneurysms and those near the bone. First, 42 patients with suspected intracranial aneurysms underwent both 256-row CT angiography (CTA) and 3DRA. Volume rendering (VR) images were captured using the conventional CT workstation. Next, VR images were transferred to the stereoscopic virtual reality display system. Two radiologists independently assessed the results that were obtained using the conventional CT workstation and stereoscopic virtual reality display system. The 3DRA results were considered as the ultimate reference standard. Based on 3DRA images, 38 aneurysms were confirmed in 42 patients. Two cases were misdiagnosed and 1 was missed when the traditional CT workstation was used. The sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV), and accuracy of the conventional CT workstation were 94.7%, 85.7%, 97.3%, 75%, and99.3%, respectively, on a per-aneurysm basis. The stereoscopic virtual reality display system missed a case. The sensitivity, specificity, PPV, NPV, and accuracy of the stereoscopic virtual reality display system were 100%, 85.7%, 97.4%, 100%, and 97.8%, respectively. No difference was observed in the accuracy of the traditional CT workstation, stereoscopic virtual reality display system, and 3DRA in detecting aneurysms. The stereoscopic virtual reality display system has some advantages in detecting small aneurysms and those near the bone. The virtual reality stereoscopic vision obtained through the system was found as a useful tool in intracranial aneurysm diagnosis and pre-operative 3D imaging. Copyright © 2018 Elsevier B.V. All rights reserved.

A real-time monitoring/emergency response modeling workstation for a tritium facility

International Nuclear Information System (INIS)

Lawver, B.S.; Sims, J.M.; Baskett, R.L.

1993-07-01

At Lawrence Livermore National Laboratory (LLNL) we developed a real-time system to monitor two stacks on our tritium handling facility. The monitors transmit the stack data to a workstation which computes a 3D numerical model of atmospheric dispersion. The workstation also collects surface and upper air data from meteorological towers and a sodar. The complex meteorological and terrain setting in the Livermore Valley demands more sophisticated resolution of the three-dimensional structure of the atmosphere to reliably calculate plume dispersion than afforded by Gaussian models. We experience both mountain valley and sea breeze flows. To address these complexities, we have implemented the three-dimensional diagnostic MATHEW mass-adjusted wind field and ADPIC particle-in-cell dispersion models on the workstation for use in real-time emergency response modeling. Both MATHEW and ADPIC have shown their utility in a variety of complex settings over the last 15 years within the Department of Energy's Atmospheric Release Advisory Capability (ARAC[1,2]) project

Out of Hours Emergency Computed Tomography Brain Studies: Comparison of Standard 3 Megapixel Diagnostic Workstation Monitors With the iPad 2.

Science.gov (United States)

Salati, Umer; Leong, Sum; Donnellan, John; Kok, Hong Kuan; Buckley, Orla; Torreggiani, William

2015-11-01

The purpose was to compare performance of diagnostic workstation monitors and the Apple iPad 2 (Cupertino, CA) in interpretation of emergency computed tomography (CT) brain studies. Two experienced radiologists interpreted 100 random emergency CT brain studies on both on-site diagnostic workstation monitors and the iPad 2 via remote access. The radiologists were blinded to patient clinical details and to each other's interpretation and the study list was randomized between interpretations on different modalities. Interobserver agreement between radiologists and intraobserver agreement between modalities was determined and Cohen kappa coefficients calculated for each. Performance with regards to urgent and nonurgent abnormalities was assessed separately. There was substantial intraobserver agreement of both radiologists between the modalities with overall calculated kappa values of 0.959 and 0.940 in detecting acute abnormalities and perfect agreement with regards to hemorrhage. Intraobserver agreement kappa values were 0.939 and 0.860 for nonurgent abnormalities. Interobserver agreement between the 2 radiologists for both diagnostic monitors and the iPad 2 was also substantial ranging from 0.821-0.860. The iPad 2 is a reliable modality in the interpretation of CT brain studies in them emergency setting and for the detection of acute and chronic abnormalities, with comparable performance to standard diagnostic workstation monitors. Copyright © 2015 Canadian Association of Radiologists. Published by Elsevier Inc. All rights reserved.

Performance assessment of advanced engineering workstations for fuel management applications

International Nuclear Information System (INIS)

Turinsky, P.J.

1989-07-01

The purpose of this project was to assess the performance of an advanced engineering workstation [AEW] with regard to applications to incore fuel management for LWRs. The attributes of most interest to us that define an AEW are parallel computational hardware and graphics capabilities. The AEWs employed were super microcomputers manufactured by MASSCOMP, Inc. These computers utilize a 32-bit architecture, graphics co-processor, multi-CPUs [up to six] attached to common memory and multi-vector accelerators. 7 refs., 33 figs., 4 tabs

Processing computed tomography images by using personal computer

International Nuclear Information System (INIS)

Seto, Kazuhiko; Fujishiro, Kazuo; Seki, Hirofumi; Yamamoto, Tetsuo.

1994-01-01

Processing of CT images was attempted by using a popular personal computer. The program for image-processing was made with C compiler. The original images, acquired with CT scanner (TCT-60A, Toshiba), were transferred to the computer by 8-inch flexible diskette. Many fundamental image-processing, such as displaying image to the monitor, calculating CT value and drawing the profile curve. The result showed that a popular personal computer had ability to process CT images. It seemed that 8-inch flexible diskette was still useful medium of transferring image data. (author)

PERSONALITY AND COMPUTER ADDICTION

Directory of Open Access Journals (Sweden)

Grażyna Jurczyńska

2010-12-01

Full Text Available Background: The aim of this work is to prove the relation between the personality traits and computer addicting. The research was carried out from 2006 to 2008 among the students of High School of Information Technology in Katowice. Material and methods: Research methods: Scale of Emotional Intelligens at Work, Social Competences Questionnaire, State-Trait Anxiety Inventory – STAI, Kimberly S. Young Test, Questionnaire to Assess the Level of Crises of Values, Directivity Scale and a questionnaire of 23 questions prepared for the research purposes. Results: 12.70% of the examined population met the criteria for computer addiction. In the own view, 76.34% considered themselves addicted to this medium. Conclusions: Personality traits such as emotional intelligence at work, inclination to authoritative behaviors as well as the value system may have influence on the addicting to a computer. No such relation was proven with reference to self – efficacy and anxious personality.

Computer-aided diagnosis workstation and teleradiology network system for chest diagnosis using the web medical image conference system with a new information security solution

Science.gov (United States)

Satoh, Hitoshi; Niki, Noboru; Eguchi, Kenji; Ohmatsu, Hironobu; Kaneko, Masahiro; Kakinuma, Ryutaro; Moriyama, Noriyuki

2010-03-01

Diagnostic MDCT imaging requires a considerable number of images to be read. Moreover, the doctor who diagnoses a medical image is insufficient in Japan. Because of such a background, we have provided diagnostic assistance methods to medical screening specialists by developing a lung cancer screening algorithm that automatically detects suspected lung cancers in helical CT images, a coronary artery calcification screening algorithm that automatically detects suspected coronary artery calcification and a vertebra body analysis algorithm for quantitative evaluation of osteoporosis. We also have developed the teleradiology network system by using web medical image conference system. In the teleradiology network system, the security of information network is very important subjects. Our teleradiology network system can perform Web medical image conference in the medical institutions of a remote place using the web medical image conference system. We completed the basic proof experiment of the web medical image conference system with information security solution. We can share the screen of web medical image conference system from two or more web conference terminals at the same time. An opinion can be exchanged mutually by using a camera and a microphone that are connected with the workstation that builds in some diagnostic assistance methods. Biometric face authentication used on site of teleradiology makes "Encryption of file" and "Success in login" effective. Our Privacy and information security technology of information security solution ensures compliance with Japanese regulations. As a result, patients' private information is protected. Based on these diagnostic assistance methods, we have developed a new computer-aided workstation and a new teleradiology network that can display suspected lesions three-dimensionally in a short time. The results of this study indicate that our radiological information system without film by using computer-aided diagnosis

Know Your Personal Computer Introduction to Computers

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 1; Issue 1. Know Your Personal Computer Introduction to Computers. Siddhartha Kumar Ghoshal. Series Article Volume 1 Issue 1 January 1996 pp 48-55. Fulltext. Click here to view fulltext PDF. Permanent link:

Integrated telemedicine workstation for intercontinental grand rounds

Science.gov (United States)

Willis, Charles E.; Leckie, Robert G.; Brink, Linda; Goeringer, Fred

1995-04-01

The Telemedicine Spacebridge to Moscow was a series of intercontinental sessions sponsored jointly by NASA and the Moscow Academy of Medicine. To improve the quality of medical images presented, the MDIS Project developed a workstation for acquisition, storage, and interactive display of radiology and pathology images. The workstation was based on a Macintosh IIfx platform with a laser digitizer for radiographs and video capture capability for microscope images. Images were transmitted via the Russian Lyoutch Satellite which had only a single video channel available and no high speed data channels. Two workstations were configured -- one for use at the Uniformed Services University of Health Sciences in Bethesda, MD. and the other for use at the Hospital of the Interior in Moscow, Russia. The two workstations were used may times during 16 sessions. As clinicians used the systems, we modified the original configuration to improve interactive use. This project demonstrated that numerous acquisition and output devices could be brought together in a single interactive workstation. The video images were satisfactory for remote consultation in a grand rounds format.

SunFast: A sun workstation based, fuel analysis scoping tool for pressurized water reactors

International Nuclear Information System (INIS)

Bohnhoff, W.J.

1991-05-01

The objective of this research was to develop a fuel cycle scoping program for light water reactors and implement the program on a workstation class computer. Nuclear fuel management problems are quite formidable due to the many fuel arrangement options available. Therefore, an engineer must perform multigroup diffusion calculations for a variety of different strategies in order to determine an optimum core reload. Standard fine mesh finite difference codes result in a considerable computational cost. A better approach is to build upon the proven reliability of currently available mainframe computer programs, and improve the engineering efficiency by taking advantage of the most useful characteristic of workstations: enhanced man/machine interaction. This dissertation contains a description of the methods and a user's guide for the interactive fuel cycle scoping program, SunFast. SunFast provides computational speed and accuracy of solution along with a synergetic coupling between the user and the machine. It should prove to be a valuable tool when extensive sets of similar calculations must be done at a low cost as is the case for assessing fuel management strategies. 40 refs

Personalized Empathic Computing (PEC)

NARCIS (Netherlands)

van Beusekom, W.; van den Broek, Egon; van der Heijden, M.; Janssen, J.H.; Spaak, E.

2006-01-01

Until a decade ago, computers were only used by experts, for professional purposes solely. Nowadays, the personal computer (PC) is standard equipment in most western housekeepings and is used to gather information, play games, communicate, etc. In parallel, users' expectations increase and,

A workstation based spectrometry application for ECR ion source [Paper No.: G5

International Nuclear Information System (INIS)

Suresh Babu, R.M.; . PS Div.)

1993-01-01

A program for an Electron Cyclotron Resonance (ECR) Ion Source beam diagnostics application in a X-Windows/Motif based workstation environment is discussed. The application program controls the hardware and acquires data via a front end computer across a local area network. The data is subsequently processed for displaying on the workstation console. The timing for data acquisition and control is determined by the particle source timing. The user interface has been implemented using the Motif widget set and the actions have been implemented through call back routines. The equipment interface is through a set of database driven calls across the network. (author). 7 refs., 1 fig

A user interface on networked workstations for MFTF-B plasma diagnostic instruments

International Nuclear Information System (INIS)

Balch, T.R.; Renbarger, V.L.

1986-01-01

A network of Sun-2/170 workstations is used to provide an interface to the MFTF-B Plasma Diagnostics System at Lawrence Livermore National Laboratory. The Plasma Diagnostics System (PDS) is responsible for control of MFTF-B plasma diagnostic instrumentation. An EtherNet Local Area Network links the workstations to a central multiprocessing system which furnishes data processing, data storage and control services for PDS. These workstations permit a physicist to command data acquisition, data processing, instrument control, and display of results. The interface is implemented as a metaphorical desktop, which helps the operator form a mental model of how the system works. As on a real desktop, functions are provided by sheets of paper (windows on a CRT screen) called worksheets. The worksheets may be invoked by pop-up menus and may be manipulated with a mouse. These worksheets are actually tasks that communicate with other tasks running in the central computer system. By making entries in the appropriate worksheet, a physicist may specify data acquisition or processing, control a diagnostic, or view a result

Sensitivity Analysis of Personal Exposure Assessment Using a Computer Simulated Person

DEFF Research Database (Denmark)

Brohus, Henrik; Jensen, H. K.

2009-01-01

The paper considers uncertainties related to personal exposure assessment using a computer simulated person. CFD is used to simulate a uniform flow field around a human being to determine the personal exposure to a contaminant source. For various vertical locations of a point contaminant source...... three additional factors are varied, namely the velocity, details of the computer simulated person, and the CFD model of the wind channel. The personal exposure is found to be highly dependent on the relative source location. Variation in the range of two orders of magnitude is found. The exposure...

Montecarlo Simulations for a Lep Experiment with Unix Workstation Clusters

Science.gov (United States)

Bonesini, M.; Calegari, A.; Rossi, P.; Rossi, V.

Modular systems of RISC CPU based computers have been implemented for large productions of Montecarlo simulated events for the DELPHI experiment at CERN. From a pilot system based on DEC 5000 CPU’s, a full size system based on a CONVEX C3820 UNIX supercomputer and a cluster of HP 735 workstations has been put into operation as a joint effort between INFN Milano and CILEA.

Zoning and workstation analysis in interventional cardiology

International Nuclear Information System (INIS)

Degrange, J.P.

2009-01-01

As interventional cardiology can induce high doses not only for patients but also for the personnel, the delimitation of regulated areas (or zoning) and workstation analysis (dosimetry) are very important in terms of radioprotection. This paper briefly recalls methods and tools for the different steps to perform zoning and workstation analysis. It outlines the peculiarities of interventional cardiology, presents methods and tools adapted to interventional cardiology, and then discusses the same issues but for workstation analysis. It also outlines specific problems which can be met, and their possible adapted solutions

CAD on personal computers

International Nuclear Information System (INIS)

Lee, Seong U; Cho, Cheol Ho; Ko, Il Du

1990-02-01

This book contains four studies of CAD on personal computers. The first thing is computer graphics in computer-aided design by Seong U Lee. The second thing is graphics primer and programming with Fortran by Seong U Lee. The third thing is application of Auto cad by Il Do Ko. The last thing is application of CAD in building construction design by Cheol Ho Cho.

Personal computers in high energy physics

International Nuclear Information System (INIS)

Quarrie, D.R.

1987-01-01

The role of personal computers within HEP is expanding as their capabilities increase and their cost decreases. Already they offer greater flexibility than many low-cost graphics terminals for a comparable cost and in addition they can significantly increase the productivity of physicists and programmers. This talk will discuss existing uses for personal computers and explore possible future directions for their integration into the overall computing environment. (orig.)

Implementation of a high-resolution workstation for primary diagnosis of projection radiography images

Science.gov (United States)

Good, Walter F.; Herron, John M.; Maitz, Glenn S.; Gur, David; Miller, Stephen L.; Straub, William H.; Fuhrman, Carl R.

1990-08-01

We designed and implemented a high-resolution video workstation as the central hardware component in a comprehensive multi-project program comparing the use of digital and film modalities. The workstation utilizes a 1.8 GByte real-time disk (RCI) capable of storing 400 full-resolution images and two Tektronix (GMA251) display controllers with 19" monitors (GMA2O2). The display is configured in a portrait format with a resolution of 1536 x 2048 x 8 bit, and operates at 75 Hz in a noninterlaced mode. Transmission of data through a 12 to 8 bit lookup table into the display controllers occurs at 20 MBytes/second (.35 seconds per image). The workstation allows easy use of brightness (level) and contrast (window) to be manipulated with a trackball, and various processing options can be selected using push buttons. Display of any of the 400 images is also performed at 20MBytes/sec (.35 sec/image). A separate text display provides for the automatic display of patient history data and for a scoring form through which readers can interact with the system by means of a computer mouse. In addition, the workstation provides for the randomization of cases and for the immediate entry of diagnostic responses into a master database. Over the past year this workstation has been used for over 10,000 readings in diagnostic studies related to 1) image resolution; 2) film vs. soft display; 3) incorporation of patient history data into the reading process; and 4) usefulness of image processing.

Personal computers in accelerator control

International Nuclear Information System (INIS)

Anderssen, P.S.

1988-01-01

The advent of the personal computer has created a popular movement which has also made a strong impact on science and engineering. Flexible software environments combined with good computational performance and large storage capacities are becoming available at steadily decreasing costs. Of equal importance, however, is the quality of the user interface offered on many of these products. Graphics and screen interaction is available in ways that were only possible on specialized systems before. Accelerator engineers were quick to pick up the new technology. The first applications were probably for controllers and data gatherers for beam measurement equipment. Others followed, and today it is conceivable to make personal computer a standard component of an accelerator control system. This paper reviews the experience gained at CERN so far and describes the approach taken in the design of the common control center for the SPS and the future LEP accelerators. The design goal has been to be able to integrate personal computers into the accelerator control system and to build the operator's workplace around it. (orig.)

Control by personal computer and Interface 1

International Nuclear Information System (INIS)

Kim, Eung Mug; Park, Sun Ho

1989-03-01

This book consists of three chapters. The first chapter deals with basic knowledge of micro computer control which are computer system, micro computer system, control of the micro computer and control system for calculator. The second chapter describes Interface about basic knowledge such as 8255 parallel interface, 6821 parallel interface, parallel interface of personal computer, reading BCD code in parallel interface, IEEE-488 interface, RS-232C interface and transmit data in personal computer and a measuring instrument. The third chapter includes control experiment by micro computer, experiment by eight bit computer and control experiment by machine code and BASIC.

Control of a pulse height analyzer using an RDX workstation

International Nuclear Information System (INIS)

Montelongo, S.; Hunt, D.N.

1984-12-01

The Nuclear Chemistry Division of Lawrence Livermore National laboratory is in the midst of upgrading its radiation counting facilities to automate data acquisition and quality control. This upgrade requires control of a pulse height analyzer (PHA) from an interactive LSI-11/23 workstation running RSX-11M. The PHA is a micro-computer based multichannel analyzer system providing data acquisition, storage, display, manipulation and input/output from up to four independent acquisition interfaces. Control of the analyzer includes reading and writing energy spectra, issuing commands, and servicing device interrupts. The analyzer communicates to the host system over a 9600-baud serial line using the Digital Data Communications link level Protocol (DDCMP). We relieved the RSX workstation CPU from the DDCMP overhead by implementing a DEC compatible in-house designed DMA serial line board (the ISL-11) to communicate with the analyzer. An RSX I/O device driver was written to complete the path between the analyzer and the RSX system by providing the link between the communication board and an application task. The I/O driver is written to handle several ISL-11 cards all operating in parallel thus providing support for control of multiple analyzers from a single workstation. The RSX device driver, its design and use by application code controlling the analyzer, and its operating environment will be discussed

The role of the mainframe terminated : mainframe versus workstation

CERN Document Server

Williams, D O

1991-01-01

I. What mainframes? - The surgeon-general has determined that you shall treat all costs with care ( continental effects, discounts assumed, next month's or last month's prices, optimism of the reporter. II. Typical mainframe hardware III. Typical mainframe software IV. What workstations? VI. Typical workstation hardware VII. Typical workstation software VIII. Titan vs PDP-7s XIX.Historic answer X. Amdahl's Law....

Development of PSA workstation KIRAP

Energy Technology Data Exchange (ETDEWEB)

Kim, Tae Un; Han, Sang Hoon; Kim, Kil You; Yang, Jun Eon; Jeong, Won Dae; Chang, Seung Cheol; Sung, Tae Yong; Kang, Dae Il; Park, Jin Hee; Lee, Yoon Hwan; Hwang, Mi Jeong

1997-01-01

Advanced Research Group of Korea Atomic Energy Research Institute has been developing the Probabilistic Safety Assessment(PSA) workstation KIRAP from 1992. This report describes the recent development activities of PSA workstation KIRAP. The first is to develop and improve the methodologies for PSA quantification, that are the incorporation of fault tree modularization technique, the improvement of cut set generation method, the development of rule-based recovery, the development of methodology to solve a fault tree which has the logical loops and to handle a fault tree which has several initiators. These methodologies are incorporated in the PSA quantification software KIRAP-CUT. The second is to convert PSA modeling softwares for Windows, which have been used on the DOS environment since 1987. The developed softwares are the fault tree editor KWTREE, the event tree editor CONPAS, and Data manager KWDBMAN for event data and common cause failure (CCF) data. With the development of PSA workstation, it makes PSA modeling and PSA quantification and automation easier and faster. (author). 8 refs.

Development of PSA workstation KIRAP

International Nuclear Information System (INIS)

Kim, Tae Un; Han, Sang Hoon; Kim, Kil You; Yang, Jun Eon; Jeong, Won Dae; Chang, Seung Cheol; Sung, Tae Yong; Kang, Dae Il; Park, Jin Hee; Lee, Yoon Hwan; Hwang, Mi Jeong.

1997-01-01

Advanced Research Group of Korea Atomic Energy Research Institute has been developing the Probabilistic Safety Assessment(PSA) workstation KIRAP from 1992. This report describes the recent development activities of PSA workstation KIRAP. The first is to develop and improve the methodologies for PSA quantification, that are the incorporation of fault tree modularization technique, the improvement of cut set generation method, the development of rule-based recovery, the development of methodology to solve a fault tree which has the logical loops and to handle a fault tree which has several initiators. These methodologies are incorporated in the PSA quantification software KIRAP-CUT. The second is to convert PSA modeling softwares for Windows, which have been used on the DOS environment since 1987. The developed softwares are the fault tree editor KWTREE, the event tree editor CONPAS, and Data manager KWDBMAN for event data and common cause failure (CCF) data. With the development of PSA workstation, it makes PSA modeling and PSA quantification and automation easier and faster. (author). 8 refs

Implementation of Active Workstations in University Libraries—A Comparison of Portable Pedal Exercise Machines and Standing Desks

Directory of Open Access Journals (Sweden)

Camille Bastien Tardif

2018-06-01

Full Text Available Sedentary behaviors are an important issue worldwide, as prolonged sitting time has been associated with health problems. Recently, active workstations have been developed as a strategy to counteract sedentary behaviors. The present study examined the rationale and perceptions of university students’ and staff following their first use of an active workstation in library settings. Ninety-nine volunteers completed a self-administered questionnaire after using a portable pedal exercise machine (PPEM or a standing desk (SD. Computer tasks were performed on the SD (p = 0.001 and paperwork tasks on a PPEM (p = 0.037 to a larger extent. Men preferred the SD and women chose the PPEM (p = 0.037. The appreciation of the PPEM was revealed to be higher than for the SD, due to its higher scores for effective, useful, functional, convenient, and comfortable dimensions. Younger participants (<25 years of age found the active workstation more pleasant to use than older participants, and participants who spent between 4 to 8 h per day in a seated position found active workstations were more effective and convenient than participants sitting fewer than 4 h per day. The results of this study are a preliminary step to better understanding the feasibility and acceptability of active workstations on university campuses.

A Next Generation BioPhotonics Workstation

DEFF Research Database (Denmark)

Glückstad, Jesper; Palima, Darwin; Tauro, Sandeep

2011-01-01

We are developing a Next Generation BioPhotonics Workstation to be applied in research on regulated microbial cell growth including their underlying physiological mechanisms, in vivo characterization of cell constituents and manufacturing of nanostructures and meta-materials.......We are developing a Next Generation BioPhotonics Workstation to be applied in research on regulated microbial cell growth including their underlying physiological mechanisms, in vivo characterization of cell constituents and manufacturing of nanostructures and meta-materials....

Contamination control in HVAC systems for aseptic processing area. Part I: Case study of the airflow velocity in a unidirectional airflow workstation with computational fluid dynamics.

Science.gov (United States)

Ogawa, M

2000-01-01

A unidirectional airflow workstation for processing a sterile pharmaceutical product is required to be "Grade A," according to EU-GMP and WHO-GMP. These regulations have employed the wording of "laminar airflow" for unidirectional airflow, with an unclear definition given. This seems to have allowed many reports to describe discussion of airflow velocity only. The guidance values as to the velocity are expressed in various words of 90 ft/min, 0.45 m/sec, 0.3 m/sec, +/- 20%, or "homogeneous air speed." It has been also little clarified how variation in airflow velocity gives influences on contamination control of a workstation working with varying key characteristics, such as ceiling height, internal heat load, internal particle generation, etc. The present author has revealed following points from a case study using Computational Fluid Dynamics: the airflow characteristic in Grade A area shows no significant changes with varying the velocity of supplied airflow, and the particles generated from the operator will be exhausted outside Grade A area without contamination.

Radiology workstation for mammography: preliminary observations, eyetracker studies, and design

Science.gov (United States)

Beard, David V.; Johnston, Richard E.; Pisano, Etta D.; Hemminger, Bradley M.; Pizer, Stephen M.

1991-07-01

For the last four years, the UNC FilmPlane project has focused on constructing a radiology workstation facilitating CT interpretations equivalent to those with film and viewbox. Interpretation of multiple CT studies was originally chosen because handling such large numbers of images was considered to be one of the most difficult tasks that could be performed with a workstation. The authors extend the FilmPlane design to address mammography. The high resolution and contrast demands coupled with the number of images often cross- compared make mammography a difficult challenge for the workstation designer. This paper presents the results of preliminary work with workstation interpretation of mammography. Background material is presented to justify why the authors believe electronic mammographic workstations could improve health care delivery. The results of several observation sessions and a preliminary eyetracker study of multiple-study mammography interpretations are described. Finally, tentative conclusions of what a mammographic workstation might look like and how it would meet clinical demand to be effective are presented.

The Impact of Ergonomically Designed Workstations on Shoulder EMG Activity during Carpet Weaving

Directory of Open Access Journals (Sweden)

Majid Motamedzade

2014-12-01

Full Text Available Background: The present study aimed to evaluate the biomechanical exposure to the trapezius muscle activity in female weavers for a prolonged period in the workstation A (suggested by previous studies and workstation B (proposed by the present study. Methods: Electromyography data were collected from nine females during four hours for each ergonomically designed workstation at the Ergonomics Laboratory, Hamadan, Iran. The design criteria for ergonomically designed workstations were: 1 weaving height (20 and 3 cm above elbow height for workstations A and B, respectively, and 2 seat type (10° and 0° forwardsloping seat for workstations A and B, respectively. Results: The amplitude probability distribution function (APDF analysis showed that the left and right upper trapezius muscle activity was almost similar at each workstation. Trapezius muscle activity in the workstation A was significantly greater than workstations B (P<0.001. Conclusion: In general, use of workstation B leads to significantly reduced muscle activity levels in the upper trapezius as compared to workstation A in weavers. Despite the positive impact of workstation B in reducing trapezius muscle activity, it seems that constrained postures of the upper arm during weaving may be associated with musculoskeletal symptoms.

[From data entry to data presentation at a clinical workstation--experiences with Anesthesia Information Management Systems (AIMS)].

Science.gov (United States)

Benson, M; Junger, A; Quinzio, L; Michel, A; Sciuk, G; Fuchs, C; Marquardt, K; Hempelmannn, G

2000-09-01

Anesthesia Information Management Systems (AIMS) are required to supply large amounts of data for various purposes such as performance recording, quality assurance, training, operating room management and research. It was our objective to establish an AIMS that enables every member of the department to independently access queries at his/her work station and at the same time allows the presentation of data in a suitable manner in order to increase the transfer of different information to the clinical workstation. Apple Macintosh Clients (Apple Computer, Inc. Cupertino, California) and the file- and database servers were installed into the already partially existing hospital network. The most important components installed on each computer are the anesthesia documenting software NarkoData (ProLogic GmbH, Erkrath), HIS client software and a HTML browser. More than 250 queries for easy evaluation were formulated with the software Voyant (Brossco Systems, Espoo, Finland). Together with the documentation they are the evaluation module of the AIMS. Today, more than 20,000 anesthesia procedures are recorded each year at 112 decentralised workstations with the AIMS. In 1998, 90.8% of the 20,383 performed anesthetic procedures were recorded online and 9.2% entered postopeatively into the system. With a corresponding user access it is possible to receive all available patient data at each single anesthesiological workstation via HIS (diagnoses, laboratory results) anytime. The available information includes previous anesthesia records, statistics and all data available from the hospitals intranet. This additional information is of great advantage in comparison to previous working conditions. The implementation of an AIMS allowed to greatly enhance the quota but also the quality of documentation and an increased flow of information at the anesthesia workstation. The circuit between data entry and the presentation and evaluation of data, statistics and results directly

Performance of radiant cooling ceiling combined with personalized ventilation in an office room: identification of thermal conditions

DEFF Research Database (Denmark)

Lipczynska, Aleksandra; Kaczmarczyk, Jan; Melikov, Arsen Krikor

2014-01-01

were performed in a test room arranged as an office with 2 workstations and 2 seating occupants resembled by thermal manikins. Heat gain of 66-72 W/m2 was simulated in the room (occupants, computers, lighting, solar gain). The air temperature in the chamber was maintained at 26°C and 28°C. Personalized...

Transient analysis capabilities at ABB-CE

International Nuclear Information System (INIS)

Kling, C.L.

1992-01-01

The transient capabilities at ABB-Combustion Engineering (ABB-CE) Nuclear Power are a function of the computer hardware and related network used, the computer software that has evolved over the years, and the commercial technical exchange agreements with other related organizations and customers. ABB-CEA is changing from a mainframe/personal computer network to a distributed workstation/personal computer local area network. The paper discusses computer hardware, mainframe computing, personal computers, mainframe/personal computer networks, workstations, transient analysis computer software, design/operation transient analysis codes, safety (licensed) analysis codes, cooperation with ABB-Atom, and customer support

The use of personal computers in reactor physics

International Nuclear Information System (INIS)

Cullen, D.E.

1988-01-01

This paper points out that personal computers are now powerful enough (in terms of core size and speed) to allow them to be used for serious reactor physics applications. In addition the low cost of personal computers means that even small institutes can now have access to a significant amount of computer power. At the present time distribution centers, such as RSIC, are beginning to distribute reactor physics codes for use on personal computers; hopefully in the near future more and more of these codes will become available through distribution centers, such as RSIC

Post-deployment usability evaluation of a radiology workstation

NARCIS (Netherlands)

Jorritsma, Wiard; Cnossen, Fokie; Dierckx, Rudi A.; Oudkerk, Matthijs; Van Ooijen, Peter M. A.

Objectives: To determine the number, nature and severity of usability issues radiologists encounter while using a commercially available radiology workstation in clinical practice, and to assess how well the results of a pre-deployment usability evaluation of this workstation generalize to clinical

IUE Data Analysis Software for Personal Computers

Science.gov (United States)

Thompson, R.; Caplinger, J.; Taylor, L.; Lawton , P.

1996-01-01

This report summarizes the work performed for the program titled, "IUE Data Analysis Software for Personal Computers" awarded under Astrophysics Data Program NRA 92-OSSA-15. The work performed was completed over a 2-year period starting in April 1994. As a result of the project, 450 IDL routines and eight database tables are now available for distribution for Power Macintosh computers and Personal Computers running Windows 3.1.

Development of a low-cost virtual reality workstation for training and education

Science.gov (United States)

Phillips, James A.

1996-01-01

Virtual Reality (VR) is a set of breakthrough technologies that allow a human being to enter and fully experience a 3-dimensional, computer simulated environment. A true virtual reality experience meets three criteria: (1) it involves 3-dimensional computer graphics; (2) it includes real-time feedback and response to user actions; and (3) it must provide a sense of immersion. Good examples of a virtual reality simulator are the flight simulators used by all branches of the military to train pilots for combat in high performance jet fighters. The fidelity of such simulators is extremely high -- but so is the price tag, typically millions of dollars. Virtual reality teaching and training methods are manifestly effective, but the high cost of VR technology has limited its practical application to fields with big budgets, such as military combat simulation, commercial pilot training, and certain projects within the space program. However, in the last year there has been a revolution in the cost of VR technology. The speed of inexpensive personal computers has increased dramatically, especially with the introduction of the Pentium processor and the PCI bus for IBM-compatibles, and the cost of high-quality virtual reality peripherals has plummeted. The result is that many public schools, colleges, and universities can afford a PC-based workstation capable of running immersive virtual reality applications. My goal this summer was to assemble and evaluate such a system.

Optimizing the pathology workstation "cockpit": Challenges and solutions

Directory of Open Access Journals (Sweden)

Elizabeth A Krupinski

2010-01-01

Full Text Available The 21 st century has brought numerous changes to the clinical reading (i.e., image or virtual pathology slide interpretation environment of pathologists and it will continue to change even more dramatically as information and communication technologies (ICTs become more widespread in the integrated healthcare enterprise. The extent to which these changes impact the practicing pathologist differ as a function of the technology under consideration, but digital "virtual slides" and the viewing of images on computer monitors instead of glass slides through a microscope clearly represents a significant change in the way that pathologists extract information from these images and render diagnostic decisions. One of the major challenges facing pathologists in this new era is how to best optimize the pathology workstation, the reading environment and the new and varied types of information available in order to ensure efficient and accurate processing of this information. Although workstations can be stand-alone units with images imported via external storage devices, this scenario is becoming less common as pathology departments connect to information highways within their hospitals and to external sites. Picture Archiving and Communications systems are no longer confined to radiology departments but are serving the entire integrated healthcare enterprise, including pathology. In radiology, the workstation is often referred to as the "cockpit" with a "digital dashboard" and the reading room as the "control room." Although pathology has yet to "go digital" to the extent that radiology has, lessons derived from radiology reading "cockpits" can be quite valuable in setting up the digital pathology reading room. In this article, we describe the concept of the digital dashboard and provide some recent examples of informatics-based applications that have been shown to improve the workflow and quality in digital reading environments.

Human Response to Personalized Ventilation Combined with Chilled Ceiling

DEFF Research Database (Denmark)

Lipczynska, Aleksandra; Kaczmarczyk, Jan; Marcol, Bartosz

2014-01-01

Personalized ventilation (PV) improves inhaled air quality, because it provides fresh air to each workstation and directly to occupant’s breathing zone. Previous research was focused on combining PV with additional total volume air distribution, i.e. mixing ventilation or displacement ventilation......, the use of radiant ceiling cooling will provide operative temperature lower than the air temperature and will improve further occupants’ thermal comfort at warm environment. Therefore combining PV with chilled ceiling may be an effective way to provide thermal comfort in rooms at temperature higher than...... temperature for chilled ceiling was 15,5/16,8°C at room air temperature of 26°C and 19,5/20,6°C at 28°C. During the experiment the subjects were performing typical office tasks at workstations with computers. Exposure included also increased activity level office work for a period of 25 min...

[Design and development of the DSA digital subtraction workstation].

Science.gov (United States)

Peng, Wen-Xian; Peng, Tian-Zhou; Xia, Shun-Ren; Jin, Guang-Bo

2008-05-01

According to the patient examination criterion and the demands of all related departments, the DSA digital subtraction workstation has been successfully designed and is introduced in this paper by analyzing the characteristic of video source of DSA which was manufactured by GE Company and has no DICOM standard interface. The workstation includes images-capturing gateway and post-processing software. With the developed workstation, all images from this early DSA equipment are transformed into DICOM format and then are shared in different machines.

Know Your Personal Computer

Indian Academy of Sciences (India)

easily developed. A device that does not plug ... them and this is what we will study in this article and the ones to follow. Personal computers .... General, Control Data, Texas Instruments and Cray Research attempted downsizing their popular ...

Prospective pilot study of a tablet computer in an Emergency Department.

Science.gov (United States)

Horng, Steven; Goss, Foster R; Chen, Richard S; Nathanson, Larry A

2012-05-01

The recent availability of low-cost tablet computers can facilitate bedside information retrieval by clinicians. To evaluate the effect of physician tablet use in the Emergency Department. Prospective cohort study comparing physician workstation usage with and without a tablet. 55,000 visits/year Level 1 Emergency Department at a tertiary academic teaching hospital. 13 emergency physicians (7 Attendings, 4 EM3s, and 2 EM1s) worked a total of 168 scheduled shifts (130 without and 38 with tablets) during the study period. Physician use of a tablet computer while delivering direct patient care in the Emergency Department. The primary outcome measure was the time spent using the Emergency Department Information System (EDIS) at a computer workstation per shift. The secondary outcome measure was the number of EDIS logins at a computer workstation per shift. Clinician use of a tablet was associated with a 38min (17-59) decrease in time spent per shift using the EDIS at a computer workstation (pcomputer was associated with a reduction in the number of times physicians logged into a computer workstation and a reduction in the amount of time they spent there using the EDIS. The presumed benefit is that decreasing time at a computer workstation increases physician availability at the bedside. However, this association will require further investigation. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

An Imaging And Graphics Workstation For Image Sequence Analysis

Science.gov (United States)

Mostafavi, Hassan

1990-01-01

This paper describes an application-specific engineering workstation designed and developed to analyze imagery sequences from a variety of sources. The system combines the software and hardware environment of the modern graphic-oriented workstations with the digital image acquisition, processing and display techniques. The objective is to achieve automation and high throughput for many data reduction tasks involving metric studies of image sequences. The applications of such an automated data reduction tool include analysis of the trajectory and attitude of aircraft, missile, stores and other flying objects in various flight regimes including launch and separation as well as regular flight maneuvers. The workstation can also be used in an on-line or off-line mode to study three-dimensional motion of aircraft models in simulated flight conditions such as wind tunnels. The system's key features are: 1) Acquisition and storage of image sequences by digitizing real-time video or frames from a film strip; 2) computer-controlled movie loop playback, slow motion and freeze frame display combined with digital image sharpening, noise reduction, contrast enhancement and interactive image magnification; 3) multiple leading edge tracking in addition to object centroids at up to 60 fields per second from both live input video or a stored image sequence; 4) automatic and manual field-of-view and spatial calibration; 5) image sequence data base generation and management, including the measurement data products; 6) off-line analysis software for trajectory plotting and statistical analysis; 7) model-based estimation and tracking of object attitude angles; and 8) interface to a variety of video players and film transport sub-systems.

The Temple Translator's Workstation Project

National Research Council Canada - National Science Library

Vanni, Michelle; Zajac, Remi

1996-01-01

.... The Temple Translator's Workstation is incorporated into a Tipster document management architecture and it allows both translator/analysts and monolingual analysts to use the machine- translation...

An advanced tube wear and fatigue workstation to predict flow induced vibrations of steam generator tubes

International Nuclear Information System (INIS)

Gay, N.; Baratte, C.; Flesch, B.

1997-01-01

Flow induced tube vibration damage is a major concern for designers and operators of nuclear power plant steam generators (SG). The operating flow-induced vibrational behaviour has to be estimated accurately to allow a precise evaluation of the new safety margins in order to optimize the maintenance policy. For this purpose, an industrial 'Tube Wear and Fatigue Workstation', called 'GEVIBUS Workstation' and based on an advanced methodology for predictive analysis of flow-induced vibration of tube bundles subject to cross-flow has been developed at Electricite de France. The GEVIBUS Workstation is an interactive processor linking modules as: thermalhydraulic computation, parametric finite element builder, interface between finite element model, thermalhydraulic code and vibratory response computations, refining modelling of fluid-elastic and random forces, linear and non-linear dynamic response and the coupled fluid-structure system, evaluation of tube damage due to fatigue and wear, graphical outputs. Two practical applications are also presented in the paper; the first simulation refers to an experimental set-up consisting of a straight tube bundle subject to water cross-flow, while the second one deals with an industrial configuration which has been observed in some operating steam generators i.e., top tube support plate degradation. In the first case the GEVIBUS predictions in terms of tube displacement time histories and phase planes have been found in very good agreement with experiment. In the second application the GEVIBUS computation showed that a tube with localized degradation is much more stable than a tube located in an extended degradation zone. Important conclusions are also drawn concerning maintenance. (author)

Know Your Personal Computer

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 1; Issue 11. Know Your Personal Computer 5. The CPU Base Instruction Set and Assembly Language Programming. Siddhartha Kumar Ghoshal ... Supercomputer Education and Research Centre, Indian Institute of Science, Bangalore 560 012, India ...

Know Your Personal Computer

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 11. Know Your Personal Computer - You and Your PC. Siddhartha Kumar Ghoshal. Series Article Volume 2 Issue 11 November 1997 pp 14-22. Fulltext. Click here to view fulltext PDF. Permanent link:

Know Your Personal Computer

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 9. Know Your Personal Computer High-Level Operating Systems. Siddhartha Kumar Ghoshal. Series Article Volume 2 Issue 9 September 1997 pp 11-17. Fulltext. Click here to view fulltext PDF. Permanent link:

ASTEC: Controls analysis for personal computers

Science.gov (United States)

Downing, John P.; Bauer, Frank H.; Thorpe, Christopher J.

1989-01-01

The ASTEC (Analysis and Simulation Tools for Engineering Controls) software is under development at Goddard Space Flight Center (GSFC). The design goal is to provide a wide selection of controls analysis tools at the personal computer level, as well as the capability to upload compute-intensive jobs to a mainframe or supercomputer. The project is a follow-on to the INCA (INteractive Controls Analysis) program that has been developed at GSFC over the past five years. While ASTEC makes use of the algorithms and expertise developed for the INCA program, the user interface was redesigned to take advantage of the capabilities of the personal computer. The design philosophy and the current capabilities of the ASTEC software are described.

The Fermilab central computing facility architectural model

International Nuclear Information System (INIS)

Nicholls, J.

1989-01-01

The goal of the current Central Computing Upgrade at Fermilab is to create a computing environment that maximizes total productivity, particularly for high energy physics analysis. The Computing Department and the Next Computer Acquisition Committee decided upon a model which includes five components: an interactive front-end, a Large-Scale Scientific Computer (LSSC, a mainframe computing engine), a microprocessor farm system, a file server, and workstations. With the exception of the file server, all segments of this model are currently in production: a VAX/VMS cluster interactive front-end, an Amdahl VM Computing engine, ACP farms, and (primarily) VMS workstations. This paper will discuss the implementation of the Fermilab Central Computing Facility Architectural Model. Implications for Code Management in such a heterogeneous environment, including issues such as modularity and centrality, will be considered. Special emphasis will be placed on connectivity and communications between the front-end, LSSC, and workstations, as practiced at Fermilab. (orig.)

The Fermilab Central Computing Facility architectural model

International Nuclear Information System (INIS)

Nicholls, J.

1989-05-01

The goal of the current Central Computing Upgrade at Fermilab is to create a computing environment that maximizes total productivity, particularly for high energy physics analysis. The Computing Department and the Next Computer Acquisition Committee decided upon a model which includes five components: an interactive front end, a Large-Scale Scientific Computer (LSSC, a mainframe computing engine), a microprocessor farm system, a file server, and workstations. With the exception of the file server, all segments of this model are currently in production: a VAX/VMS Cluster interactive front end, an Amdahl VM computing engine, ACP farms, and (primarily) VMS workstations. This presentation will discuss the implementation of the Fermilab Central Computing Facility Architectural Model. Implications for Code Management in such a heterogeneous environment, including issues such as modularity and centrality, will be considered. Special emphasis will be placed on connectivity and communications between the front-end, LSSC, and workstations, as practiced at Fermilab. 2 figs

High-performance mass storage system for workstations

Science.gov (United States)

Chiang, T.; Tang, Y.; Gupta, L.; Cooperman, S.

1993-01-01

Reduced Instruction Set Computer (RISC) workstations and Personnel Computers (PC) are very popular tools for office automation, command and control, scientific analysis, database management, and many other applications. However, when using Input/Output (I/O) intensive applications, the RISC workstations and PC's are often overburdened with the tasks of collecting, staging, storing, and distributing data. Also, by using standard high-performance peripherals and storage devices, the I/O function can still be a common bottleneck process. Therefore, the high-performance mass storage system, developed by Loral AeroSys' Independent Research and Development (IR&D) engineers, can offload a RISC workstation of I/O related functions and provide high-performance I/O functions and external interfaces. The high-performance mass storage system has the capabilities to ingest high-speed real-time data, perform signal or image processing, and stage, archive, and distribute the data. This mass storage system uses a hierarchical storage structure, thus reducing the total data storage cost, while maintaining high-I/O performance. The high-performance mass storage system is a network of low-cost parallel processors and storage devices. The nodes in the network have special I/O functions such as: SCSI controller, Ethernet controller, gateway controller, RS232 controller, IEEE488 controller, and digital/analog converter. The nodes are interconnected through high-speed direct memory access links to form a network. The topology of the network is easily reconfigurable to maximize system throughput for various applications. This high-performance mass storage system takes advantage of a 'busless' architecture for maximum expandability. The mass storage system consists of magnetic disks, a WORM optical disk jukebox, and an 8mm helical scan tape to form a hierarchical storage structure. Commonly used files are kept in the magnetic disk for fast retrieval. The optical disks are used as archive

EPRI root cause advisory workstation 'ERCAWS'

International Nuclear Information System (INIS)

Singh, A.; Chiu, C.; Hackman, R.B.

1993-01-01

EPRI and its contractor FPI International are developing Personal Computer (PC), Microsoft Windows based software to assist power plant engineers and maintenance personnel to diagnose and correct root causes of power plant equipment failures. The EPRI Root Cause Advisory Workstation (ERCAWS) is easy to use and able to handle knowledge bases and diagnostic tools for an unlimited number of equipment types. Knowledge base data is based on power industry experience and root cause analysis from many sources - Utilities, EPRI, US government, FPI, and International sources. The approach used in the knowledge base handling portion of the software is case-study oriented with the engineer selecting the equipment type and symptom identification using a combination of text, photographs, and animation, displaying dynamic physical phenomena involved. Root causes, means for confirmation, and corrective actions are then suggested in a simple, user friendly format. The first knowledge base being released with ERCAWS is the Valve Diagnostic Advisor module; covering six common valve types and some motor operator and air operator items. More modules are under development with Heat Exchanger, Bolt, and Piping modules currently in the beta testing stage. A wide variety of diagnostic tools are easily incorporated into ERCAWS and accessed through the main screen interface. ERCAWS is designed to fulfill the industry need for user-friendly tools to perform power plant equipment failure root cause analysis, and training for engineering, operations and maintenance personnel on how components can fail and how to reduce failure rates or prevent failure from occurring. In addition, ERCAWS serves as a vehicle to capture lessons learned from industry wide experience. (author)

The biomechanical and physiological effect of two dynamic workstations

NARCIS (Netherlands)

Botter, J.; Burford, E.M.; Commissaris, D.; Könemann, R.; Mastrigt, S.H.V.; Ellegast, R.P.

2013-01-01

The aim of this research paper was to investigate the effect, both biomechanically and physiologically, of two dynamic workstations currently available on the commercial market. The dynamic workstations tested, namely the Treadmill Desk by LifeSpan and the LifeBalance Station by RightAngle, were

The development of a Flight Test Engineer's Workstation for the Automated Flight Test Management System

Science.gov (United States)

Tartt, David M.; Hewett, Marle D.; Duke, Eugene L.; Cooper, James A.; Brumbaugh, Randal W.

1989-01-01

The Automated Flight Test Management System (ATMS) is being developed as part of the NASA Aircraft Automation Program. This program focuses on the application of interdisciplinary state-of-the-art technology in artificial intelligence, control theory, and systems methodology to problems of operating and flight testing high-performance aircraft. The development of a Flight Test Engineer's Workstation (FTEWS) is presented, with a detailed description of the system, technical details, and future planned developments. The goal of the FTEWS is to provide flight test engineers and project officers with an automated computer environment for planning, scheduling, and performing flight test programs. The FTEWS system is an outgrowth of the development of ATMS and is an implementation of a component of ATMS on SUN workstations.

Design of a tritium decontamination workstation based on plasma cleaning

International Nuclear Information System (INIS)

Antoniazzi, A.B.; Shmayda, W.T.; Fishbien, B.F.

1993-01-01

A design for a tritium decontamination workstation based on plasma cleaning is presented. The activity of tritiated surfaces are significantly reduced through plasma-surface interactions within the workstation. Such a workstation in a tritium environment can routinely be used to decontaminate tritiated tools and components. The main advantage of such a station is the lack of low level tritiated liquid waste. Gaseous tritiated species are the waste products with can with present technology be separated and contained

Viewport: an object-oriented approach to integrate workstation software for tile and stack mode display.

Science.gov (United States)

Ghosh, S; Andriole, K P; Avrin, D E

1997-08-01

Diagnostic workstation design has migrated towards display presentation in one of two modes: tiled images or stacked images. It is our impression that the workstation setup or configuration in each of these two modes is rather distinct. We sought to establish a commonality to simplify software design, and to enable a single descriptor method to facilitate folder manager development of "hanging" protocols. All current workstation designs use a combination of "off-screen" and "on-screen" memory whether or not they use a dedicated display subsystem, or merely a video board. Most diagnostic workstations also have two or more monitors. Our central concept is that of a "logical" viewport that can be smaller than, the same size as, or larger than a single monitor. Each port "views" an image data sequence loaded into offscreen memory. Each viewport can display one or more images in sequence in a one-on-one or traditionally tiled presentation. Viewports can be assigned to the available monitor "real estate" in any manner that fits. For example, a single sequence computed tomography (CT) study could be displayed across all monitors in a tiled appearance by assigning a single large viewport to the monitors. At the other extreme, a multisequence magnetic resonance (MR) study could be compared with a similar previous study by assigning four viewports to each monitor, single image display per viewport, and assigning four of the sequences of the current study to the left monitor viewports, and four of the earlier study to the right monitor viewports. Ergonomic controls activate scrolling through the off-screen image sequence data. Workstation folder manager hanging protocols could then specify viewports, number of images per viewport, and the automatic assignment of appropriately named sequences of current and previous studies to the viewports on a radiologist-specific basis. Furthermore, software development is simplified by common base objects and methods of the tile and stack

Functional requirements document for the Earth Observing System Data and Information System (EOSDIS) Scientific Computing Facilities (SCF) of the NASA/MSFC Earth Science and Applications Division, 1992

Science.gov (United States)

Botts, Michael E.; Phillips, Ron J.; Parker, John V.; Wright, Patrick D.

1992-01-01

Five scientists at MSFC/ESAD have EOS SCF investigator status. Each SCF has unique tasks which require the establishment of a computing facility dedicated to accomplishing those tasks. A SCF Working Group was established at ESAD with the charter of defining the computing requirements of the individual SCFs and recommending options for meeting these requirements. The primary goal of the working group was to determine which computing needs can be satisfied using either shared resources or separate but compatible resources, and which needs require unique individual resources. The requirements investigated included CPU-intensive vector and scalar processing, visualization, data storage, connectivity, and I/O peripherals. A review of computer industry directions and a market survey of computing hardware provided information regarding important industry standards and candidate computing platforms. It was determined that the total SCF computing requirements might be most effectively met using a hierarchy consisting of shared and individual resources. This hierarchy is composed of five major system types: (1) a supercomputer class vector processor; (2) a high-end scalar multiprocessor workstation; (3) a file server; (4) a few medium- to high-end visualization workstations; and (5) several low- to medium-range personal graphics workstations. Specific recommendations for meeting the needs of each of these types are presented.

The scheme and implementing of workstation configuration for medical imaging information system

International Nuclear Information System (INIS)

Tao Yonghao; Miao Jingtao

2002-01-01

Objective: To discuss the scheme and implementing for workstation configuration of medical imaging information system which would be adapted to the practice situation of China. Methods: The workstations were logically divided into PACS workstations and RIS workstations, the former applied to three kinds of diagnostic practice: the small matrix images, large matrix images, and high resolution gray scale display application, and the latter consisted of many different models which depended upon the usage and function process. Results: A dual screen configuration for image diagnostic workstation integrated the image viewing and reporting procedure physically, while the small matrix images as CT or MR were operated on 17 in (1 in = 2.54 cm) color monitors, the conventional X-ray diagnostic procedure was implemented based on 21 in color monitors or portrait format gray scale 2 K by 2.5 K monitors. All other RIS workstations not involved in image process were set up with a common PC configuration. Conclusion: The essential principle for designing a workstation scheme of medical imaging information system should satisfy the basic requirements of medical image diagnosis and fit into the available investment situation

Modelling of Energy Expenditure at Welding Workstations: Effect of ...

African Journals Online (AJOL)

The welding workstation usually generates intense heat during operations, which may affect the welder's health if not properly controlled, and can also affect the performance of the welder at work. Consequently, effort to control the conditions of the welding workstation is essential, and is therefore pursued in this paper.

Workout at work: laboratory test of psychological and performance outcomes of active workstations.

Science.gov (United States)

Sliter, Michael; Yuan, Zhenyu

2015-04-01

With growing concerns over the obesity epidemic in the United States and other developed countries, many organizations have taken steps to incorporate healthy workplace practices. However, most workers are still sedentary throughout the day--a major contributor to individual weight gain. The current study sought to gather preliminary evidence of the efficacy of active workstations, which are a possible intervention that could increase employees' physical activity while they are working. We conducted an experimental study, in which boredom, task satisfaction, stress, arousal, and performance were evaluated and compared across 4 randomly assigned conditions: seated workstation, standing workstation, cycling workstation, and walking workstation. Additionally, body mass index (BMI) and exercise habits were examined as moderators to determine whether differences in these variables would relate to increased benefits in active conditions. The results (n = 180) showed general support for the benefits of walking workstations, whereby participants in the walking condition had higher satisfaction and arousal and experienced less boredom and stress than those in the passive conditions. Cycling workstations, on the other hand, tended to relate to reduced satisfaction and performance when compared with other conditions. The moderators did not impact these relationships, indicating that walking workstations might have psychological benefits to individuals, regardless of BMI and exercise habits. The results of this study are a preliminary step in understanding the work implications of active workstations. (c) 2015 APA, all rights reserved).

RI management by personal computer

International Nuclear Information System (INIS)

Ono, Isamu; Hiyoshi, Katsunori; Ono, Kazuhiko; Morimitsu, Wataru

1983-01-01

For RI-handling facilities up to medium scale, it has been studied whether a personal computer is applicable to the practical management of radioisotopes. In the present system, the number of writing in mini floppy disks is 1280 articles per diskette, which is the sufficient capacity for a storage medium for one year in variety of books. The correction of radioactivity decay as well as various totalizations can be made easily, so that the state of RI storage and use for the whole RI-handling facility can be grasped. Further, by the improvement of the output formats, the transfer to the books as obligated to write is possible. From the above reason, a personal computer is practically applicable with the management system and also leads to labor saving in RI management personnel. (Mori, K.)

Applying human factors to the design of control centre and workstation of a nuclear reactor

Energy Technology Data Exchange (ETDEWEB)

Santos, Isaac J.A. Luquetti dos; Carvalho, Paulo V.R.; Goncalves, Gabriel de L., E-mail: luquetti@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Souza, Tamara D.M.F.; Falcao, Mariana A. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Dept. de Desenho Industrial

2013-07-01

Human factors is a body of scientific factors about human characteristics, covering biomedical, psychological and psychosocial considerations, including principles and applications in the personnel selection areas, training, job performance aid tools and human performance evaluation. Control Centre is a combination of control rooms, control suites and local control stations which are functionally related and all on the same site. Digital control room includes an arrangement of systems, equipment such as computers and communication terminals and workstations at which control and monitoring functions are conducted by operators. Inadequate integration between control room and operators reduces safety, increases the operation complexity, complicates operator training and increases the likelihood of human errors occurrence. The objective of this paper is to present a specific approach for the conceptual and basic design of the control centre and workstation of a nuclear reactor used to produce radioisotope. The approach is based on human factors standards, guidelines and the participation of a multidisciplinary team in the conceptual and basic phases of the design. Using the information gathered from standards and from the multidisciplinary team, an initial sketch 3D of the control centre and workstation are being developed. (author)

Applying human factors to the design of control centre and workstation of a nuclear reactor

International Nuclear Information System (INIS)

Santos, Isaac J.A. Luquetti dos; Carvalho, Paulo V.R.; Goncalves, Gabriel de L.; Souza, Tamara D.M.F.; Falcao, Mariana A.

2013-01-01

Human factors is a body of scientific factors about human characteristics, covering biomedical, psychological and psychosocial considerations, including principles and applications in the personnel selection areas, training, job performance aid tools and human performance evaluation. Control Centre is a combination of control rooms, control suites and local control stations which are functionally related and all on the same site. Digital control room includes an arrangement of systems, equipment such as computers and communication terminals and workstations at which control and monitoring functions are conducted by operators. Inadequate integration between control room and operators reduces safety, increases the operation complexity, complicates operator training and increases the likelihood of human errors occurrence. The objective of this paper is to present a specific approach for the conceptual and basic design of the control centre and workstation of a nuclear reactor used to produce radioisotope. The approach is based on human factors standards, guidelines and the participation of a multidisciplinary team in the conceptual and basic phases of the design. Using the information gathered from standards and from the multidisciplinary team, an initial sketch 3D of the control centre and workstation are being developed. (author)

Design of the HANARO operator workstation having the enhanced usability and data handling capability

International Nuclear Information System (INIS)

Kim, M. J.; Kim, Y. K.; Jung, H. S.; Choi, Y. S.; Woo, J. S.; Jeon, B. J.

2003-01-01

As a first step to the upgrade plan of the HANARO reactor control computer system, we furnished IBM workstation class PC to replace the existing operator workstation, the dedicated HMI console. Also designed is the new human-machine interface by using the commercial HMI development software that is operating on the MS-Windows. We expect that we would not have any more difficulties in preparing replacement parts and providing maintenance of hardware. In this paper, we introduce the features of new interface, which adopted the virtue of the existing design and enabled the safe and efficient reactor operation by correcting the demerits. Also described are the functionality of historian server that provides the simpler storage, retrieval and search operation and the design of trend display screen that replaces the existing chart recorder by using the dual monitor feature of PC graphic card

Nuclear power plant simulation using advanced simulation codes through a state-of-the-art workstation

International Nuclear Information System (INIS)

Laats, E.T.; Hagen, R.N.

1985-01-01

The Nuclear Plant Analyzer (NPA) currently resides in a Control Data Corporation 176 mainframe computer at the Idaho National Engineering Laboratory (INEL). The NPA user community is expanding to include worldwide users who cannot consistently access the INEL mainframe computer from their own facilities. Thus, an alternate mechanism is needed to enable their use of the NPA. Therefore, a feasibility study was undertaken by EG and G Idaho to evaluate the possibility of developing a standalone workstation dedicated to the NPA

The Impact of Active Workstations on Workplace Productivity and Performance: A Systematic Review.

Science.gov (United States)

Ojo, Samson O; Bailey, Daniel P; Chater, Angel M; Hewson, David J

2018-02-27

Active workstations have been recommended for reducing sedentary behavior in the workplace. It is important to understand if the use of these workstations has an impact on worker productivity. The aim of this systematic review was to examine the effect of active workstations on workplace productivity and performance. A total of 3303 articles were initially identified by a systematic search and seven articles met eligibility criteria for inclusion. A quality appraisal was conducted to assess risk of bias, confounding, internal and external validity, and reporting. Most of the studies reported cognitive performance as opposed to productivity. Five studies assessed cognitive performance during use of an active workstation, usually in a single session. Sit-stand desks had no detrimental effect on performance, however, some studies with treadmill and cycling workstations identified potential decreases in performance. Many of the studies lacked the power required to achieve statistical significance. Three studies assessed workplace productivity after prolonged use of an active workstation for between 12 and 52 weeks. These studies reported no significant effect on productivity. Active workstations do not appear to decrease workplace performance.

Functional magnetic resonance maps obtained by personal computer

International Nuclear Information System (INIS)

Gomez, F. j.; Manjon, J. V.; Robles, M.; Marti-Bonmati, L.; Dosda, R.; Molla, E.

2001-01-01

Functional magnetic resonance (fMR) is of special relevance in the analysis of certain types of brain activation. The present report describes the development of a simple software program for use with personal computers (PCs) that analyzes these images and provides functional activation maps. Activation maps are based on the temporal differences in oxyhemoglobin in tomographic images. To detect these differences, intensities registered repeatedly during brain control and activation are compared. The experiments were performed with a 1.5-Tesla MR unit. To verify the reliability of the program fMR studies were carried out in 4 healthy individuals (12 contiguous slices, 80 images per slice every 3.1 seconds for a total of 960 images). All the images were transferred to a PC and were processed pixel by pixel within each sequence to obtain an intensity/time curve. The statistical study of the results (Student's test and cross correlation analysis) made it possible to establish the activation of each pixel. The images were prepared using spatial filtering, temporal filtering, baseline correction, normalization and segmentation of the parenchyma. The postprocessing of the results involved the elimination of single pixels, superposition of an anatomical image of greater spatial resolution and anti-aliasing. The application (Xfun 1.0, Valencia, Spain) was developed in Microsoft Visual C++5.0 Developer Studio for Windows NT Workstation. As a representative example, the program took 8.2 seconds to calculate and present the results of the entire study (12 functional maps). In the motor and visual activation experiments, the activation corresponding to regions proximal to the central sulcus of the hemisphere contralateral to the hand that moved and in the occipital cortex were observed. While programs that calculate activation maps are available, the development of software for PCs running Microsoft Windows ensures several key features for its use on a daily basis: it is easy

Accessible high performance computing solutions for near real-time image processing for time critical applications

Science.gov (United States)

Bielski, Conrad; Lemoine, Guido; Syryczynski, Jacek

2009-09-01

High Performance Computing (HPC) hardware solutions such as grid computing and General Processing on a Graphics Processing Unit (GPGPU) are now accessible to users with general computing needs. Grid computing infrastructures in the form of computing clusters or blades are becoming common place and GPGPU solutions that leverage the processing power of the video card are quickly being integrated into personal workstations. Our interest in these HPC technologies stems from the need to produce near real-time maps from a combination of pre- and post-event satellite imagery in support of post-disaster management. Faster processing provides a twofold gain in this situation: 1. critical information can be provided faster and 2. more elaborate automated processing can be performed prior to providing the critical information. In our particular case, we test the use of the PANTEX index which is based on analysis of image textural measures extracted using anisotropic, rotation-invariant GLCM statistics. The use of this index, applied in a moving window, has been shown to successfully identify built-up areas in remotely sensed imagery. Built-up index image masks are important input to the structuring of damage assessment interpretation because they help optimise the workload. The performance of computing the PANTEX workflow is compared on two different HPC hardware architectures: (1) a blade server with 4 blades, each having dual quad-core CPUs and (2) a CUDA enabled GPU workstation. The reference platform is a dual CPU-quad core workstation and the PANTEX workflow total computing time is measured. Furthermore, as part of a qualitative evaluation, the differences in setting up and configuring various hardware solutions and the related software coding effort is presented.

SCWEB, Scientific Workstation Evaluation Benchmark

Energy Technology Data Exchange (ETDEWEB)

Raffenetti, R C [Computing Services-Support Services Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States)

1988-06-16

1 - Description of program or function: The SCWEB (Scientific Workstation Evaluation Benchmark) software includes 16 programs which are executed in a well-defined scenario to measure the following performance capabilities of a scientific workstation: implementation of FORTRAN77, processor speed, memory management, disk I/O, monitor (or display) output, scheduling of processing (multiprocessing), and scheduling of print tasks (spooling). 2 - Method of solution: The benchmark programs are: DK1, DK2, and DK3, which do Fourier series fitting based on spline techniques; JC1, which checks the FORTRAN function routines which produce numerical results; JD1 and JD2, which solve dense systems of linear equations in double- and single-precision, respectively; JD3 and JD4, which perform matrix multiplication in single- and double-precision, respectively; RB1, RB2, and RB3, which perform substantial amounts of I/O processing on files other than the input and output files; RR1, which does intense single-precision floating-point multiplication in a tight loop, RR2, which initializes a 512x512 integer matrix in a manner which skips around in the address space rather than initializing each consecutive memory cell in turn; RR3, which writes alternating text buffers to the output file; RR4, which evaluates the timer routines and demonstrates that they conform to the specification; and RR5, which determines whether the workstation is capable of executing a 4-megabyte program

Computer-based personality judgments are more accurate than those made by humans.

Science.gov (United States)

Youyou, Wu; Kosinski, Michal; Stillwell, David

2015-01-27

Judging others' personalities is an essential skill in successful social living, as personality is a key driver behind people's interactions, behaviors, and emotions. Although accurate personality judgments stem from social-cognitive skills, developments in machine learning show that computer models can also make valid judgments. This study compares the accuracy of human and computer-based personality judgments, using a sample of 86,220 volunteers who completed a 100-item personality questionnaire. We show that (i) computer predictions based on a generic digital footprint (Facebook Likes) are more accurate (r = 0.56) than those made by the participants' Facebook friends using a personality questionnaire (r = 0.49); (ii) computer models show higher interjudge agreement; and (iii) computer personality judgments have higher external validity when predicting life outcomes such as substance use, political attitudes, and physical health; for some outcomes, they even outperform the self-rated personality scores. Computers outpacing humans in personality judgment presents significant opportunities and challenges in the areas of psychological assessment, marketing, and privacy.

ARCIMBOLDO_LITE: single-workstation implementation and use.

Science.gov (United States)

Sammito, Massimo; Millán, Claudia; Frieske, Dawid; Rodríguez-Freire, Eloy; Borges, Rafael J; Usón, Isabel

2015-09-01

ARCIMBOLDO solves the phase problem at resolutions of around 2 Å or better through massive combination of small fragments and density modification. For complex structures, this imposes a need for a powerful grid where calculations can be distributed, but for structures with up to 200 amino acids in the asymmetric unit a single workstation may suffice. The use and performance of the single-workstation implementation, ARCIMBOLDO_LITE, on a pool of test structures with 40-120 amino acids and resolutions between 0.54 and 2.2 Å is described. Inbuilt polyalanine helices and iron cofactors are used as search fragments. ARCIMBOLDO_BORGES can also run on a single workstation to solve structures in this test set using precomputed libraries of local folds. The results of this study have been incorporated into an automated, resolution- and hardware-dependent parameterization. ARCIMBOLDO has been thoroughly rewritten and three binaries are now available: ARCIMBOLDO_LITE, ARCIMBOLDO_SHREDDER and ARCIMBOLDO_BORGES. The programs and libraries can be downloaded from http://chango.ibmb.csic.es/ARCIMBOLDO_LITE.

The Impact of Active Workstations on Workplace Productivity and Performance: A Systematic Review

Directory of Open Access Journals (Sweden)

Samson O. Ojo

2018-02-01

Full Text Available Active workstations have been recommended for reducing sedentary behavior in the workplace. It is important to understand if the use of these workstations has an impact on worker productivity. The aim of this systematic review was to examine the effect of active workstations on workplace productivity and performance. A total of 3303 articles were initially identified by a systematic search and seven articles met eligibility criteria for inclusion. A quality appraisal was conducted to assess risk of bias, confounding, internal and external validity, and reporting. Most of the studies reported cognitive performance as opposed to productivity. Five studies assessed cognitive performance during use of an active workstation, usually in a single session. Sit-stand desks had no detrimental effect on performance, however, some studies with treadmill and cycling workstations identified potential decreases in performance. Many of the studies lacked the power required to achieve statistical significance. Three studies assessed workplace productivity after prolonged use of an active workstation for between 12 and 52 weeks. These studies reported no significant effect on productivity. Active workstations do not appear to decrease workplace performance.

Image sequence analysis workstation for multipoint motion analysis

Science.gov (United States)

Mostafavi, Hassan

1990-08-01

This paper describes an application-specific engineering workstation designed and developed to analyze motion of objects from video sequences. The system combines the software and hardware environment of a modem graphic-oriented workstation with the digital image acquisition, processing and display techniques. In addition to automation and Increase In throughput of data reduction tasks, the objective of the system Is to provide less invasive methods of measurement by offering the ability to track objects that are more complex than reflective markers. Grey level Image processing and spatial/temporal adaptation of the processing parameters is used for location and tracking of more complex features of objects under uncontrolled lighting and background conditions. The applications of such an automated and noninvasive measurement tool include analysis of the trajectory and attitude of rigid bodies such as human limbs, robots, aircraft in flight, etc. The system's key features are: 1) Acquisition and storage of Image sequences by digitizing and storing real-time video; 2) computer-controlled movie loop playback, freeze frame display, and digital Image enhancement; 3) multiple leading edge tracking in addition to object centroids at up to 60 fields per second from both live input video or a stored Image sequence; 4) model-based estimation and tracking of the six degrees of freedom of a rigid body: 5) field-of-view and spatial calibration: 6) Image sequence and measurement data base management; and 7) offline analysis software for trajectory plotting and statistical analysis.

Can We Afford These Affordances? GarageBand and the Double-Edged Sword of the Digital Audio Workstation

Science.gov (United States)

Bell, Adam Patrick

2015-01-01

The proliferation of computers, tablets, and smartphones has resulted in digital audio workstations (DAWs) such as GarageBand in being some of the most widely distributed musical instruments. Positing that software designers are dictating the music education of DAW-dependent music-makers, I examine the fallacy that music-making applications such…

Methodological Aspects of Modelling and Simulation of Robotized Workstations

Directory of Open Access Journals (Sweden)

Naqib Daneshjo

2018-05-01

Full Text Available From the point of view of development of application and program products, key directions that need to be respected in computer support for project activities are quite clearly specified. User interfaces with a high degree of graphical interactive convenience, two-dimensional and three-dimensional computer graphics contribute greatly to streamlining project methodologies and procedures in particular. This is mainly due to the fact that a high number of solved tasks is clearly graphic in the modern design of robotic systems. Automation of graphical character tasks is therefore a significant development direction for the subject area. The authors present results of their research in the area of automation and computer-aided design of robotized systems. A new methodical approach to modelling robotic workstations, consisting of ten steps incorporated into the four phases of the logistics process of creating and implementing a robotic workplace, is presented. The emphasis is placed on the modelling and simulation phase with verification of elaborated methodologies on specific projects or elements of the robotized welding plant in automotive production.

Intraoperative non-record-keeping usage of anesthesia information management system workstations and associated hemodynamic variability and aberrancies.

Science.gov (United States)

Wax, David B; Lin, Hung-Mo; Reich, David L

2012-12-01

Anesthesia information management system workstations in the anesthesia workspace that allow usage of non-record-keeping applications could lead to distraction from patient care. We evaluated whether non-record-keeping usage of the computer workstation was associated with hemodynamic variability and aberrancies. Auditing data were collected on eight anesthesia information management system workstations and linked to their corresponding electronic anesthesia records to identify which application was active at any given time during the case. For each case, the periods spent using the anesthesia information management system record-keeping module were separated from those spent using non-record-keeping applications. The variability of heart rate and blood pressure were also calculated, as were the incidence of hypotension, hypertension, and tachycardia. Analysis was performed to identify whether non-record-keeping activity was a significant predictor of these hemodynamic outcomes. Data were analyzed for 1,061 cases performed by 171 clinicians. Median (interquartile range) non-record-keeping activity time was 14 (1, 38) min, representing 16 (3, 33)% of a median 80 (39, 143) min of procedure time. Variables associated with greater non-record-keeping activity included attending anesthesiologists working unassisted, longer case duration, lower American Society of Anesthesiologists status, and general anesthesia. Overall, there was no independent association between non-record-keeping workstation use and hemodynamic variability or aberrancies during anesthesia either between cases or within cases. Anesthesia providers spent sizable portions of case time performing non-record-keeping applications on anesthesia information management system workstations. This use, however, was not independently associated with greater hemodynamic variability or aberrancies in patients during maintenance of general anesthesia for predominantly general surgical and gynecologic procedures.

Computer-based personality judgments are more accurate than those made by humans

Science.gov (United States)

Youyou, Wu; Kosinski, Michal; Stillwell, David

2015-01-01

Judging others’ personalities is an essential skill in successful social living, as personality is a key driver behind people’s interactions, behaviors, and emotions. Although accurate personality judgments stem from social-cognitive skills, developments in machine learning show that computer models can also make valid judgments. This study compares the accuracy of human and computer-based personality judgments, using a sample of 86,220 volunteers who completed a 100-item personality questionnaire. We show that (i) computer predictions based on a generic digital footprint (Facebook Likes) are more accurate (r = 0.56) than those made by the participants’ Facebook friends using a personality questionnaire (r = 0.49); (ii) computer models show higher interjudge agreement; and (iii) computer personality judgments have higher external validity when predicting life outcomes such as substance use, political attitudes, and physical health; for some outcomes, they even outperform the self-rated personality scores. Computers outpacing humans in personality judgment presents significant opportunities and challenges in the areas of psychological assessment, marketing, and privacy. PMID:25583507

A new workstation based man/machine interface system for the JT-60 Upgrade

International Nuclear Information System (INIS)

Yonekawa, I.; Shimono, M.; Totsuka, T.; Yamagishi, K.

1992-01-01

Development of a new man/machine interface system was stimulated by the requirements of making the JT-60 operator interface more 'friendly' on the basis of the past five-year operational experience. Eleven Sun/3 workstations and their supervisory mini-computer HIDIC V90/45 are connected through the standard network; Ethernet. The network is also connected to the existing 'ZENKEI' mini-computer system through the shared memory on the HIDIC V90/45 mini-computer. Improved software, such as automatic setting of the discharge conditions, consistency check among the related parameters and easy operation for discharge result data display, offered the 'user-friendly' environments. This new man/machine interface system leads to the efficient operation of the JT-60. (author)

MEDUSA - An overset grid flow solver for network-based parallel computer systems

Science.gov (United States)

Smith, Merritt H.; Pallis, Jani M.

1993-01-01

Continuing improvement in processing speed has made it feasible to solve the Reynolds-Averaged Navier-Stokes equations for simple three-dimensional flows on advanced workstations. Combining multiple workstations into a network-based heterogeneous parallel computer allows the application of programming principles learned on MIMD (Multiple Instruction Multiple Data) distributed memory parallel computers to the solution of larger problems. An overset-grid flow solution code has been developed which uses a cluster of workstations as a network-based parallel computer. Inter-process communication is provided by the Parallel Virtual Machine (PVM) software. Solution speed equivalent to one-third of a Cray-YMP processor has been achieved from a cluster of nine commonly used engineering workstation processors. Load imbalance and communication overhead are the principal impediments to parallel efficiency in this application.

The advanced software development workstation project

Science.gov (United States)

Fridge, Ernest M., III; Pitman, Charles L.

1991-01-01

The Advanced Software Development Workstation (ASDW) task is researching and developing the technologies required to support Computer Aided Software Engineering (CASE) with the emphasis on those advanced methods, tools, and processes that will be of benefit to support all NASA programs. Immediate goals are to provide research and prototype tools that will increase productivity, in the near term, in projects such as the Software Support Environment (SSE), the Space Station Control Center (SSCC), and the Flight Analysis and Design System (FADS) which will be used to support the Space Shuttle and Space Station Freedom. Goals also include providing technology for development, evolution, maintenance, and operations. The technologies under research and development in the ASDW project are targeted to provide productivity enhancements during the software life cycle phase of enterprise and information system modeling, requirements generation and analysis, system design and coding, and system use and maintenance. On-line user's guides will assist users in operating the developed information system with knowledge base expert assistance.

Parallelising a molecular dynamics algorithm on a multi-processor workstation

Science.gov (United States)

Müller-Plathe, Florian

1990-12-01

The Verlet neighbour-list algorithm is parallelised for a multi-processor Hewlett-Packard/Apollo DN10000 workstation. The implementation makes use of memory shared between the processors. It is a genuine master-slave approach by which most of the computational tasks are kept in the master process and the slaves are only called to do part of the nonbonded forces calculation. The implementation features elements of both fine-grain and coarse-grain parallelism. Apart from three calls to library routines, two of which are standard UNIX calls, and two machine-specific language extensions, the whole code is written in standard Fortran 77. Hence, it may be expected that this parallelisation concept can be transfered in parts or as a whole to other multi-processor shared-memory computers. The parallel code is routinely used in production work.

How to Protect Patients Digital Images/Thermograms Stored on a Local Workstation

Directory of Open Access Journals (Sweden)

J. Živčák

2010-01-01

Full Text Available To ensure the security and privacy of patient electronic medical information stored on local workstations in doctors’ offices, clinic centers, etc., it is necessary to implement a secure and reliable method for logging on and accessing this information. Biometrically-based identification technologies use measurable personal properties (physiological or behavioral such as a fingerprint in order to identify or verify a person’s identity, and provide the foundation for highly secure personal identification, verification and/or authentication solutions. The use of biometric devices (fingerprint readers is an easy and secure way to log on to the system. We have provided practical tests on HP notebooks that have the fingerprint reader integrated. Successful/failed logons have been monitored and analyzed, and calculations have been made. This paper presents the false rejection rates, false acceptance rates and failure to acquire rates.

Archetype-Based Modeling of Persona for Comprehensive Personality Computing from Personal Big Data

Science.gov (United States)

Ma, Jianhua

2018-01-01

A model describing the wide variety of human behaviours called personality, is becoming increasingly popular among researchers due to the widespread availability of personal big data generated from the use of prevalent digital devices, e.g., smartphones and wearables. Such an approach can be used to model an individual and even digitally clone a person, e.g., a Cyber-I (cyber individual). This work is aimed at establishing a unique and comprehensive description for an individual to mesh with various personalized services and applications. An extensive research literature on or related to psychological modelling exists, i.e., into automatic personality computing. However, the integrity and accuracy of the results from current automatic personality computing is insufficient for the elaborate modeling in Cyber-I due to an insufficient number of data sources. To reach a comprehensive psychological description of a person, it is critical to bring in heterogeneous data sources that could provide plenty of personal data, i.e., the physiological data, and the Internet data. In addition, instead of calculating personality traits from personal data directly, an approach to a personality model derived from the theories of Carl Gustav Jung is used to measure a human subject’s persona. Therefore, this research is focused on designing an archetype-based modeling of persona covering an individual’s facets in different situations to approach a comprehensive personality model. Using personal big data to measure a specific persona in a certain scenario, our research is designed to ensure the accuracy and integrity of the generated personality model. PMID:29495343

Archetype-Based Modeling of Persona for Comprehensive Personality Computing from Personal Big Data

Directory of Open Access Journals (Sweden)

Ao Guo

2018-02-01

Full Text Available A model describing the wide variety of human behaviours called personality, is becoming increasingly popular among researchers due to the widespread availability of personal big data generated from the use of prevalent digital devices, e.g., smartphones and wearables. Such an approach can be used to model an individual and even digitally clone a person, e.g., a Cyber-I (cyber individual. This work is aimed at establishing a unique and comprehensive description for an individual to mesh with various personalized services and applications. An extensive research literature on or related to psychological modelling exists, i.e., into automatic personality computing. However, the integrity and accuracy of the results from current automatic personality computing is insufficient for the elaborate modeling in Cyber-I due to an insufficient number of data sources. To reach a comprehensive psychological description of a person, it is critical to bring in heterogeneous data sources that could provide plenty of personal data, i.e., the physiological data, and the Internet data. In addition, instead of calculating personality traits from personal data directly, an approach to a personality model derived from the theories of Carl Gustav Jung is used to measure a human subject’s persona. Therefore, this research is focused on designing an archetype-based modeling of persona covering an individual’s facets in different situations to approach a comprehensive personality model. Using personal big data to measure a specific persona in a certain scenario, our research is designed to ensure the accuracy and integrity of the generated personality model.

Archetype-Based Modeling of Persona for Comprehensive Personality Computing from Personal Big Data.

Science.gov (United States)

Guo, Ao; Ma, Jianhua

2018-02-25

A model describing the wide variety of human behaviours called personality, is becoming increasingly popular among researchers due to the widespread availability of personal big data generated from the use of prevalent digital devices, e.g., smartphones and wearables. Such an approach can be used to model an individual and even digitally clone a person, e.g., a Cyber-I (cyber individual). This work is aimed at establishing a unique and comprehensive description for an individual to mesh with various personalized services and applications. An extensive research literature on or related to psychological modelling exists, i.e., into automatic personality computing. However, the integrity and accuracy of the results from current automatic personality computing is insufficient for the elaborate modeling in Cyber-I due to an insufficient number of data sources. To reach a comprehensive psychological description of a person, it is critical to bring in heterogeneous data sources that could provide plenty of personal data, i.e., the physiological data, and the Internet data. In addition, instead of calculating personality traits from personal data directly, an approach to a personality model derived from the theories of Carl Gustav Jung is used to measure a human subject's persona. Therefore, this research is focused on designing an archetype-based modeling of persona covering an individual's facets in different situations to approach a comprehensive personality model. Using personal big data to measure a specific persona in a certain scenario, our research is designed to ensure the accuracy and integrity of the generated personality model.

Client-server computer architecture saves costs and eliminates bottlenecks

International Nuclear Information System (INIS)

Darukhanavala, P.P.; Davidson, M.C.; Tyler, T.N.; Blaskovich, F.T.; Smith, C.

1992-01-01

This paper reports that workstation, client-server architecture saved costs and eliminated bottlenecks that BP Exploration (Alaska) Inc. experienced with mainframe computer systems. In 1991, BP embarked on an ambitious project to change technical computing for its Prudhoe Bay, Endicott, and Kuparuk operations on Alaska's North Slope. This project promised substantial rewards, but also involved considerable risk. The project plan called for reservoir simulations (which historically had run on a Cray Research Inc. X-MP supercomputer in the company's Houston data center) to be run on small computer workstations. Additionally, large Prudhoe Bay, Endicott, and Kuparuk production and reservoir engineering data bases and related applications also would be moved to workstations, replacing a Digital Equipment Corp. VAX cluster in Anchorage

Using a Cray Y-MP as an array processor for a RISC Workstation

Science.gov (United States)

Lamaster, Hugh; Rogallo, Sarah J.

1992-01-01

As microprocessors increase in power, the economics of centralized computing has changed dramatically. At the beginning of the 1980's, mainframes and super computers were often considered to be cost-effective machines for scalar computing. Today, microprocessor-based RISC (reduced-instruction-set computer) systems have displaced many uses of mainframes and supercomputers. Supercomputers are still cost competitive when processing jobs that require both large memory size and high memory bandwidth. One such application is array processing. Certain numerical operations are appropriate to use in a Remote Procedure Call (RPC)-based environment. Matrix multiplication is an example of an operation that can have a sufficient number of arithmetic operations to amortize the cost of an RPC call. An experiment which demonstrates that matrix multiplication can be executed remotely on a large system to speed the execution over that experienced on a workstation is described.

Real-time on a standard UNIX workstation?

International Nuclear Information System (INIS)

Glanzman, T.

1992-09-01

This is a report of an ongoing R ampersand D project which is investigating the use of standard UNIX workstations for the real-time data acquisition from a major new experimental initiative, the SLAC B Factory (PEP II). For this work an IBM RS/6000 workstation running the AIX operating system is used. Real-time extensions to the UNIX operating system are explored and performance measured. These extensions comprise a set of AIX-specific and POSIX-compliant system services. Benchmark comparisons are made with embedded processor technologies. Results are presented for a simple prototype on-line system for laboratory-testing of a new prototype drift chamber

The algebraic manipulation program DIRAC on IBM personal computers

International Nuclear Information System (INIS)

Grozin, A.G.; Perlt, H.

1989-01-01

The version DIRAC (2.2) for IBM compatible personal computers is described. It is designed to manipulate algebraically with polynomials and tensors. After a short introduction concerning implementation and usage on personal computers an example program is given. It contains a detailed user's guide to DIRAC (2.2) and, additionally some useful applications. 4 refs

The Relationship between Personality and Computer Deviance

Science.gov (United States)

Burns, Cardra E.

2013-01-01

Computer deviance by employees, defined as malicious and nonmalicious computer use behaviors, has contributed to billions of dollars of monetary and productivity losses for public and private sector organizations. The purpose of this correlational study was to examine the relationship between personality characteristics and employees' computer…

The safety monitor and RCM workstation as complementary tools in risk based maintenance optimization

International Nuclear Information System (INIS)

Rawson, P.D.

2000-01-01

Reliability Centred Maintenance (RCM) represents a proven technique for rendering maintenance activities safer, more effective, and less expensive, in terms of systems unavailability and resource management. However, it is believed that RCM can be enhanced by the additional consideration of operational plant risk. This paper discusses how two computer-based tools, i.e., the RCM Workstation and the Safety Monitor, can complement each other in helping to create a living preventive maintenance strategy. (author)

Computed Tomography (CT) -- Head

Medline Plus

Full Text Available ... images. These images can be viewed on a computer monitor, printed on film or transferred to a ... other in a ring, called a gantry. The computer workstation that processes the imaging information is located ...

Computed Tomography (CT) -- Sinuses

Medline Plus

Full Text Available ... images. These images can be viewed on a computer monitor, printed on film or transferred to a ... other in a ring, called a gantry. The computer workstation that processes the imaging information is located ...

Computed Tomography (CT) -- Sinuses

Medline Plus

Full Text Available ... ring, called a gantry. The computer workstation that processes the imaging information is located in a separate ... follows a spiral path. A special computer program processes this large volume of data to create two- ...

Computed Tomography (CT) -- Head

Medline Plus

Full Text Available ... ring, called a gantry. The computer workstation that processes the imaging information is located in a separate ... follows a spiral path. A special computer program processes this large volume of data to create two- ...

Computed Tomography (CT) -- Sinuses

Medline Plus

Full Text Available ... other in a ring, called a gantry. The computer workstation that processes the imaging information is located ... ray beam follows a spiral path. A special computer program processes this large volume of data to ...

Progress of data processing system in JT-60 utilizing the UNIX-based workstations

International Nuclear Information System (INIS)

Sakata, Shinya; Kiyono, Kimihiro; Oshima, Takayuki; Sato, Minoru; Ozeki, Takahisa

2007-07-01

JT-60 data processing system (DPS) possesses three-level hierarchy. At the top level of hierarchy is JT-60 inter-shot processor (MSP-ISP), which is a mainframe computer, provides communication with the JT-60 supervisory control system and supervises the internal communication inside the DPS. The middle level of hierarchy has minicomputers and the bottom level of hierarchy has individual diagnostic subsystems, which consist of the CAMAC and VME modules. To meet the demand for advanced diagnostics, the DPS has been progressed in stages from a three-level hierarchy system, which was dependent on the processing power of the MSP-ISP, to a two-level hierarchy system, which is decentralized data processing system (New-DPS) by utilizing the UNIX-based workstations and network technology. This replacement had been accomplished, and the New-DPS has been started to operate in October 2005. In this report, we describe the development and improvement of the New-DPS, whose functions were decentralized from the MSP-ISP to the UNIX-based workstations. (author)

The use of bicycle workstations to increase physical activity in secondary classrooms

Directory of Open Access Journals (Sweden)

Alicia Fedewa

2017-11-01

Full Text Available Background To date, the majority of interventions have implemented classroom-based physical activity (PA at the elementary level; however, there is both the potential and need to explore student outcomes at high-school level as well, given that very few studies have incorporated classroom-based PA interventions for adolescents. One exception has been the use of bicycle workstations within secondary classrooms. Using bicycle workstations in lieu of traditional chairs in a high school setting shows promise for enhancing adolescents’ physical activity during the school day. Participants and procedure The present study explored the effects of integrating bicycle workstations into a secondary classroom setting for four months in a sample of 115 adolescents using an A-B-A-B withdrawal design. The study took place in one Advanced Placement English classroom across five groups of students. Physical activity outcomes included average heart rate, and caloric expenditure. Behavioural outcomes included percentage of on-task/off-task behaviour and number of teacher prompts in redirecting off-task behaviour. Feasibility and acceptability data of using the bicycle workstations were also collected. Results Findings showed significant improvements in physical activity as measured by heart rate and caloric expenditure, although heart rate percentage remained in the low intensity range when students were on the bicycle workstations. No effects were found on students’ on-task behaviour when using the bicycle workstations. Overall, students found the bikes acceptable to use but noted disadvantages of them as well. Conclusions Using bicycle workstations in high-school settings appears promising for enhancing low-intensity physical activity among adolescents. The limitations of the present study and implications for physical activity interventions in secondary schools are discussed.

Communication System Simulation Workstation

Science.gov (United States)

1990-01-30

SIMULATION WORKSTATION Grant # AFOSR-89-0117 Submitted to: DEPARTMENT OF AIR FORCE AIR FORCE OFFICE OF SCIENTIFIC RESEARCH BOLLING AIR FORCE BASE , DC...CORRESPONOENCiA. PAGUETES. CONIIUCE. r ACTUHA. Y CONOCIMIENTO DE EMBAROUES. THIS PURCHASE ORDER [,rccion Cablegralica .1,1 Addrv~s NO MUST APPEAR ON ALL...sub-band decomposition was developed, PKX, based on the modulation of a single prototype filter. This technicde was introduced first by Nassbauner and

Computational strategies for three-dimensional flow simulations on distributed computer systems

Science.gov (United States)

Sankar, Lakshmi N.; Weed, Richard A.

1995-08-01

This research effort is directed towards an examination of issues involved in porting large computational fluid dynamics codes in use within the industry to a distributed computing environment. This effort addresses strategies for implementing the distributed computing in a device independent fashion and load balancing. A flow solver called TEAM presently in use at Lockheed Aeronautical Systems Company was acquired to start this effort. The following tasks were completed: (1) The TEAM code was ported to a number of distributed computing platforms including a cluster of HP workstations located in the School of Aerospace Engineering at Georgia Tech; a cluster of DEC Alpha Workstations in the Graphics visualization lab located at Georgia Tech; a cluster of SGI workstations located at NASA Ames Research Center; and an IBM SP-2 system located at NASA ARC. (2) A number of communication strategies were implemented. Specifically, the manager-worker strategy and the worker-worker strategy were tested. (3) A variety of load balancing strategies were investigated. Specifically, the static load balancing, task queue balancing and the Crutchfield algorithm were coded and evaluated. (4) The classical explicit Runge-Kutta scheme in the TEAM solver was replaced with an LU implicit scheme. And (5) the implicit TEAM-PVM solver was extensively validated through studies of unsteady transonic flow over an F-5 wing, undergoing combined bending and torsional motion. These investigations are documented in extensive detail in the dissertation, 'Computational Strategies for Three-Dimensional Flow Simulations on Distributed Computing Systems', enclosed as an appendix.

Computational strategies for three-dimensional flow simulations on distributed computer systems

Science.gov (United States)

Sankar, Lakshmi N.; Weed, Richard A.

1995-01-01

This research effort is directed towards an examination of issues involved in porting large computational fluid dynamics codes in use within the industry to a distributed computing environment. This effort addresses strategies for implementing the distributed computing in a device independent fashion and load balancing. A flow solver called TEAM presently in use at Lockheed Aeronautical Systems Company was acquired to start this effort. The following tasks were completed: (1) The TEAM code was ported to a number of distributed computing platforms including a cluster of HP workstations located in the School of Aerospace Engineering at Georgia Tech; a cluster of DEC Alpha Workstations in the Graphics visualization lab located at Georgia Tech; a cluster of SGI workstations located at NASA Ames Research Center; and an IBM SP-2 system located at NASA ARC. (2) A number of communication strategies were implemented. Specifically, the manager-worker strategy and the worker-worker strategy were tested. (3) A variety of load balancing strategies were investigated. Specifically, the static load balancing, task queue balancing and the Crutchfield algorithm were coded and evaluated. (4) The classical explicit Runge-Kutta scheme in the TEAM solver was replaced with an LU implicit scheme. And (5) the implicit TEAM-PVM solver was extensively validated through studies of unsteady transonic flow over an F-5 wing, undergoing combined bending and torsional motion. These investigations are documented in extensive detail in the dissertation, 'Computational Strategies for Three-Dimensional Flow Simulations on Distributed Computing Systems', enclosed as an appendix.

Design and analysis of wudu’ (ablution) workstation for elderly in Malaysia

Science.gov (United States)

Aman, A.; Dawal, S. Z. M.; Rahman, N. I. A.

2017-06-01

Wudu’ (Ablution) workstation is one of the facilities used by most Muslims in all categories. At present, there are numbers of design guidelines for praying facilities but still lacking on wudu’ (ablution) area specification especially or elderly. Thus, It is timely to develop an ergonomic wudu’ workstation for elderly to perform ablution independently and confidently. This study was conducted to design an ergonomic ablution unit for the Muslim’s elderly in Malaysia. An ablution workstation was designed based on elderly anthropometric dimensions and was then analyse using CATIA V5R21 for posture investigation using RULAs. The results of the study has identified significant anthropometric dimensions in designing wudu’ (ablution) workstation for elderly people. This study can be considered as preliminary study for the development of an ergonomic ablution design for elderly. This effort will become one of the significant social contributions to our elderly population in developing our nation holistically.

A real-time data-acquisition and analysis system with distributed UNIX workstations

International Nuclear Information System (INIS)

Yamashita, H.; Miyamoto, K.; Maruyama, K.; Hirosawa, H.; Nakayoshi, K.; Emura, T.; Sumi, Y.

1996-01-01

A compact data-acquisition system using three RISC/UNIX TM workstations (SUN TM /SPARCstation TM ) with real-time capabilities of monitoring and analysis has been developed for the study of photonuclear reactions with the large-acceptance spectrometer TAGX. One workstation acquires data from memory modules in the front-end electronics (CAMAC and TKO) with a maximum speed of 300 Kbytes/s, where data size times instantaneous rate is 1 Kbyte x 300 Hz. Another workstation, which has real-time capability for run monitoring, gets the data with a buffer manager called NOVA. The third workstation analyzes the data and reconstructs the event. In addition to a general hardware and software description, priority settings and run control by shell scripts are described. This system has recently been used successfully in a two month long experiment. (orig.)

Computer Activities for Persons With Dementia.

Science.gov (United States)

Tak, Sunghee H; Zhang, Hongmei; Patel, Hetal; Hong, Song Hee

2015-06-01

The study examined participant's experience and individual characteristics during a 7-week computer activity program for persons with dementia. The descriptive study with mixed methods design collected 612 observational logs of computer sessions from 27 study participants, including individual interviews before and after the program. Quantitative data analysis included descriptive statistics, correlational coefficients, t-test, and chi-square. Content analysis was used to analyze qualitative data. Each participant averaged 23 sessions and 591min for 7 weeks. Computer activities included slide shows with music, games, internet use, and emailing. On average, they had a high score of intensity in engagement per session. Women attended significantly more sessions than men. Higher education level was associated with a higher number of different activities used per session and more time spent on online games. Older participants felt more tired. Feeling tired was significantly correlated with a higher number of weeks with only one session attendance per week. More anticholinergic medications taken by participants were significantly associated with a higher percentage of sessions with disengagement. The findings were significant at p < .05. Qualitative content analysis indicated tailoring computer activities appropriate to individual's needs and functioning is critical. All participants needed technical assistance. A framework for tailoring computer activities may provide guidance on developing and maintaining treatment fidelity of tailored computer activity interventions among persons with dementia. Practice guidelines and education protocols may assist caregivers and service providers to integrate computer activities into homes and aging services settings. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Evaluation of total workstation CT interpretation quality: a single-screen pilot study

Science.gov (United States)

Beard, David V.; Perry, John R.; Muller, Keith E.; Misra, Ram B.; Brown, P.; Hemminger, Bradley M.; Johnston, Richard E.; Mauro, J. Matthew; Jaques, P. F.; Schiebler, M.

1991-07-01

An interpretation report, generated with an electronic viewbox, is affected by two factors: image quality, which encompasses what can be seen on the display, and computer human interaction (CHI), which accounts for the cognitive load effect of locating, moving, and manipulating images with the workstation controls. While a number of subject experiments have considered image quality, only recently has the affect of CHI on total interpretation quality been measured. This paper presents the results of a pilot study conducted to evaluate the total interpretation quality of the FilmPlane2.2 radiology workstation for patient folders containing single forty-slice CT studies. First, radiologists interpreted cases and dictated reports using FilmPlane2.2. Requisition forms were provided. Film interpretation was provided by the original clinical report and interpretation forms generated from a previous experiment. Second, an evaluator developed a list of findings for each case based on those listed in all the reports for each case and then evaluated each report for its response on each finding. Third, the reports were compared to determine how well they agreed with one another. Interpretation speed and observation data was also gathered.

Pc-Based Floating Point Imaging Workstation

Science.gov (United States)

Guzak, Chris J.; Pier, Richard M.; Chinn, Patty; Kim, Yongmin

1989-07-01

The medical, military, scientific and industrial communities have come to rely on imaging and computer graphics for solutions to many types of problems. Systems based on imaging technology are used to acquire and process images, and analyze and extract data from images that would otherwise be of little use. Images can be transformed and enhanced to reveal detail and meaning that would go undetected without imaging techniques. The success of imaging has increased the demand for faster and less expensive imaging systems and as these systems become available, more and more applications are discovered and more demands are made. From the designer's perspective the challenge to meet these demands forces him to attack the problem of imaging from a different perspective. The computing demands of imaging algorithms must be balanced against the desire for affordability and flexibility. Systems must be flexible and easy to use, ready for current applications but at the same time anticipating new, unthought of uses. Here at the University of Washington Image Processing Systems Lab (IPSL) we are focusing our attention on imaging and graphics systems that implement imaging algorithms for use in an interactive environment. We have developed a PC-based imaging workstation with the goal to provide powerful and flexible, floating point processing capabilities, along with graphics functions in an affordable package suitable for diverse environments and many applications.

ESCRIME: testing bench for advanced operator workstations in future plants

International Nuclear Information System (INIS)

Poujol, A.; Papin, B.

1994-01-01

The problem of optimal task allocation between man and computer for the operation of nuclear power plants is of major concern for the design of future plants. As the increased level of automation induces the modification of the tasks actually devoted to the operator in the control room, it is very important to anticipate these consequences at the plant design stage. The improvement of man machine cooperation is expected to play a major role in minimizing the impact of human errors on plant safety. The CEA has launched a research program concerning the evolution of the plant operation in order to optimize the efficiency of the human/computer systems for a better safety. The objective of this program is to evaluate different modalities of man-machine share of tasks, in a representative context. It relies strongly upon the development of a specific testing facility, the ESCRIME work bench, which is presented in this paper. It consists of an EDF 1300MWe PWR plant simulator connected to an operator workstation. The plant simulator model presents at a significant level of details the instrumentation and control of the plant and the main connected circuits. The operator interface is based on the generalization of the use of interactive graphic displays, and is intended to be consistent to the tasks to be performed by the operator. The functional architecture of the workstation is modular, so that different cooperation mechanisms can be implemented within the same framework. It is based on a thorough analysis and structuration of plant control tasks, in normal as well as in accident situations. The software architecture design follows the distributed artificial intelligence approach. Cognitive agents cooperate in order to operate the process. The paper presents the basic principles and the functional architecture of the test bed and describes the steps and the present status of the program. (author)

Systems for neutronic, thermohydraulic and shielding calculation in personal computers

International Nuclear Information System (INIS)

Villarino, E.A.; Abbate, P.; Lovotti, O.; Santini, M.

1990-01-01

The MTR-PC (Materials Testing Reactors-Personal Computers) system has been developed by the Nuclear Engineering Division of INVAP S.E. with the aim of providing working conditions integrated with personal computers for design and neutronic, thermohydraulic and shielding analysis for reactors employing plate type fuel. (Author) [es

A personal computer-based nuclear magnetic resonance spectrometer

Science.gov (United States)

Job, Constantin; Pearson, Robert M.; Brown, Michael F.

1994-11-01

Nuclear magnetic resonance (NMR) spectroscopy using personal computer-based hardware has the potential of enabling the application of NMR methods to fields where conventional state of the art equipment is either impractical or too costly. With such a strategy for data acquisition and processing, disciplines including civil engineering, agriculture, geology, archaeology, and others have the possibility of utilizing magnetic resonance techniques within the laboratory or conducting applications directly in the field. Another aspect is the possibility of utilizing existing NMR magnets which may be in good condition but unused because of outdated or nonrepairable electronics. Moreover, NMR applications based on personal computer technology may open up teaching possibilities at the college or even secondary school level. The goal of developing such a personal computer (PC)-based NMR standard is facilitated by existing technologies including logic cell arrays, direct digital frequency synthesis, use of PC-based electrical engineering software tools to fabricate electronic circuits, and the use of permanent magnets based on neodymium-iron-boron alloy. Utilizing such an approach, we have been able to place essentially an entire NMR spectrometer console on two printed circuit boards, with the exception of the receiver and radio frequency power amplifier. Future upgrades to include the deuterium lock and the decoupler unit are readily envisioned. The continued development of such PC-based NMR spectrometers is expected to benefit from the fast growing, practical, and low cost personal computer market.

Personal computer as a part of radiometric gauges

International Nuclear Information System (INIS)

Machaj, B.

1992-01-01

Following the world tendency in the application of microcomputers in measuring instrumentation, standard personal computer, compatible with IBM PC/XT, was employed in the isotope gauges developed lately in the Institute. The are: beta backscatter coating thickness gauge, X-ray fluorescence multilayer coating thickness gauge with X-ray tube as radiation source, and automatic airborne dust pollution gauge. A simple interface containing: address decoder, programmable pulse counter, some buffers and latches was sufficient to connect the computer to the measuring head of the gauges. Thanks to the possibility of programming in higher level language (turbo Pascal), the gauges were developed in much shorter time than required for classical electronics. The experience gained during development of the gauges shows, that even in case of a simple instrument such as the beta backscatter coating thickness gauge, it is more economical to employ ready-made personal computer than to elaborate specific electronics for it, unless the gauge is produced in large numbers. The use of personal computer is particularly advantageous, when processing of the signal or control of the measuring cycle is more sophisticated, as in the case of the two other gauges. Block diagrams of the gauges and their interfaces are presented in the paper. In case of the airborne dust pollution gauge, flow chart of the computer program is also given. (author). 3 refs, 4 figs

Some neutronics and thermal-hydraulics codes for reactor analysis using personal computers

International Nuclear Information System (INIS)

Woodruff, W.L.

1990-01-01

Some neutronics and thermal-hydraulics codes formerly available only for main frame computers may now be run on personal computers. Brief descriptions of the codes are provided. Running times for some of the codes are compared for an assortment of personal and main frame computers. With some limitations in detail, personal computer versions of the codes can be used to solve many problems of interest in reactor analyses at very modest costs. 11 refs., 4 tabs

Evaluation of PC-based diagnostic radiology workstations

International Nuclear Information System (INIS)

Pollack, T.; Brueggenwerth, G.; Kaulfuss, K.; Niederlag, W.

2000-01-01

Material and Methods: During February 1999 and September 1999 medical users at the hospital Dresden-Friedrichstadt Germany had tested 7 types of radiology diagnostic workstations. Two types of test methods were used: In test type 1 ergonomic and handling functions were evaluated impartial according to 78 selected user requirements. In test type 2 radiologists and radiographers (3+4) performed 23 work flow steps with a subjectively evaluation. Results: By using a progressive rating no product could fully meet the user requirements. As a result of the summary evaluation for test 1 and test 2 the following compliance rating was calculated for the different products: Rad Works (66%), Magic View (63%), ID-Report (58%), Impax 3000 (53%), Medical Workstation (52%), Pathspeed (46%) and Autorad (39%). (orig.) [de

Files for workstations with ionizing radiation risks: variation in the use of gamma densitometers

International Nuclear Information System (INIS)

Tournadre, A.

2008-01-01

After a brief presentation of the different gamma-densitometers proposed by MLPC to measure roadway density, and having outlined the support role of the provider, the author describes the form and content of workstation files for workstations exhibiting a risk related to ionizing radiation. He gives an analytical overview of dose calculation: analysis of instrument use phases, exposure duration, dose rates and way of introducing these dose rates in the workstation file. He formulates how different procedures are to be followed by the radiation protection expert within the company. He outlines that workstation files are very useful as information feedback tool

From LESSEPS to the workstation for reliability engineers

International Nuclear Information System (INIS)

Ancelin, C.; Bouissou, M.; Collet, J.; Gallois, M.; Magne, L.; Villatte, N.; Yedid, C.; Mulet-Marquis, D.

1994-01-01

Three Mile Island and Chernobyl in the nuclear industry, Challenger, in the space industry, Seveso and Bhopal in the chemical industry - all these accidents show how difficult it is to forecast all likely accident scenarios that may occur in complex systems. This was, however, the objective of the probabilistic safety assessment (PSA) performed by EDF at the Paluel nuclear power plant. The full computerization of this study led to the LESSEPS project, aimed at automating three different steps: generation of reliability models -based on the use of expert systems, qualitative and quantitative processing of these models using computer codes, and overall management of PSA studies. This paper presents the results obtained and the gradual transformation of this first generation of tools into a workstation aimed at integrating reliability studies at all stages of an industrial process. (author)

A versatile nondestructive evaluation imaging workstation

Science.gov (United States)

Chern, E. James; Butler, David W.

1994-01-01

Ultrasonic C-scan and eddy current imaging systems are of the pointwise type evaluation systems that rely on a mechanical scanner to physically maneuver a probe relative to the specimen point by point in order to acquire data and generate images. Since the ultrasonic C-scan and eddy current imaging systems are based on the same mechanical scanning mechanisms, the two systems can be combined using the same PC platform with a common mechanical manipulation subsystem and integrated data acquisition software. Based on this concept, we have developed an IBM PC-based combined ultrasonic C-scan and eddy current imaging system. The system is modularized and provides capacity for future hardware and software expansions. Advantages associated with the combined system are: (1) eliminated duplication of the computer and mechanical hardware, (2) unified data acquisition, processing and storage software, (3) reduced setup time for repetitious ultrasonic and eddy current scans, and (4) improved system efficiency. The concept can be adapted to many engineering systems by integrating related PC-based instruments into one multipurpose workstation such as dispensing, machining, packaging, sorting, and other industrial applications.

Performance of personalized ventilation combined with chilled ceiling in an office room: inhaled air quality and contaminant distribution

DEFF Research Database (Denmark)

Lipczynska, Aleksandra; Kaczmarczyk, Jan; Melikov, Arsen Krikor

2014-01-01

people (exhaled air, bioeffluents) and building materials (wall painting). Personalized ventilation combined with chilled ceiling ensured highest air quality at the workstation under all conditions. Pollutant concentration in the occupied zone away from the workstations did not differ substantially...... between the tested systems. Chilled ceiling combined with personalized ventilation working as the only air supplying system may be optimal solution in many buildings.......In a simulated two persons’ office room inhaled air quality and contaminant distribution provided with personalized ventilation combined with chilled ceiling, mixing ventilation only, chilled ceiling with mixing ventilation and chilled ceiling with mixing and personalized ventilation was studied...

X-ray spectrometer instrumentation with a personal computer

International Nuclear Information System (INIS)

Skaarup, P.; Vogeley, E.

1989-01-01

A description is given of an instrumentation for control of an X-ray spectrometer used in solid state physics experiments. The instrumentation includes a personal computer (PC) and a European Computer Bus (ECB) interface system. Details are given of the operating software. (author)

Coping with distributed computing

International Nuclear Information System (INIS)

Cormell, L.

1992-09-01

The rapid increase in the availability of high performance, cost-effective RISC/UNIX workstations has been both a blessing and a curse. The blessing of having extremely powerful computing engines available on the desk top is well-known to many users. The user has tremendous freedom, flexibility, and control of his environment. That freedom can, however, become the curse of distributed computing. The user must become a system manager to some extent, he must worry about backups, maintenance, upgrades, etc. Traditionally these activities have been the responsibility of a central computing group. The central computing group, however, may find that it can no longer provide all of the traditional services. With the plethora of workstations now found on so many desktops throughout the entire campus or lab, the central computing group may be swamped by support requests. This talk will address several of these computer support and management issues by providing some examples of the approaches taken at various HEP institutions. In addition, a brief review of commercial directions or products for distributed computing and management will be given

Fab the coming revolution on your desktop : from personal computers to personal fabrication

CERN Document Server

Gershenfeld, Neil

2005-01-01

What if you could someday put the manufacturing power of an automobile plant on your desktop? According to Neil Gershenfeld, the renowned MIT scientist and inventor, the next big thing is personal fabrication-the ability to design and produce your own products, in your own home, with a machine that combines consumer electronics and industrial tools. Personal fabricators are about to revolutionize the world just as personal computers did a generation ago, and Fab shows us how.

Argo workstation: a key component of operational oceanography

Science.gov (United States)

Dong, Mingmei; Xu, Shanshan; Miao, Qingsheng; Yue, Xinyang; Lu, Jiawei; Yang, Yang

2018-02-01

Operational oceanography requires the quantity, quality, and availability of data set and the timeliness and effectiveness of data products. Without steady and strong operational system supporting, operational oceanography will never be proceeded far. In this paper we describe an integrated platform named Argo Workstation. It operates as a data processing and management system, capable of data collection, automatic data quality control, visualized data check, statistical data search and data service. After it is set up, Argo workstation provides global high quality Argo data to users every day timely and effectively. It has not only played a key role in operational oceanography but also set up an example for operational system.

Migration of nuclear criticality safety software from a mainframe to a workstation environment

International Nuclear Information System (INIS)

Bowie, L.J.; Robinson, R.C.; Cain, V.R.

1993-01-01

The Nuclear Criticality Safety Department (NCSD), Oak Ridge Y-12 Plant has undergone the transition of executing the Martin Marietta Energy Systems Nuclear Criticality Safety Software (NCSS) on IBM mainframes to a Hewlett-Packard (HP) 9000/730 workstation (NCSSHP). NCSSHP contains the following configuration controlled modules and cross-section libraries: BONAMI, CSAS, GEOMCHY, ICE, KENO IV, KENO Va, MODIIFY, NITAWL SCALE, SLTBLIB, XSDRN, UNIXLIB, albedos library, weights library, 16-Group HANSEN-ROACH master library, 27-Group ENDF/B-IV master library, and standard composition library. This paper will discuss the method used to choose the workstation, the hardware setup of the chosen workstation, an overview of Y-12 software quality assurance and configuration control methodology, code validation, difficulties encountered in migrating the codes, and advantages to migrating to a workstation environment

Application of ubiquitous computing in personal health monitoring systems.

Science.gov (United States)

Kunze, C; Grossmann, U; Stork, W; Müller-Glaser, K D

2002-01-01

A possibility to significantly reduce the costs of public health systems is to increasingly use information technology. The Laboratory for Information Processing Technology (ITIV) at the University of Karlsruhe is developing a personal health monitoring system, which should improve health care and at the same time reduce costs by combining micro-technological smart sensors with personalized, mobile computing systems. In this paper we present how ubiquitous computing theory can be applied in the health-care domain.

Computer Self-Efficacy, Computer Anxiety, Performance and Personal Outcomes of Turkish Physical Education Teachers

Science.gov (United States)

Aktag, Isil

2015-01-01

The purpose of this study is to determine the computer self-efficacy, performance outcome, personal outcome, and affect and anxiety level of physical education teachers. Influence of teaching experience, computer usage and participation of seminars or in-service programs on computer self-efficacy level were determined. The subjects of this study…

Feasibility of an Integrated Expert Video Authoring Workstation for Low-Cost Teacher Produced CBI. SBIR Phase I: Final Report.

Science.gov (United States)

IntelliSys, Inc., Syracuse, NY.

This was Phase I of a three-phased project. This phase of the project investigated the feasibility of a computer-based instruction (CBI) workstation, designed for use by teachers of handicapped students within a school structure. This station is to have as a major feature the ability to produce in-house full-motion video using one of the…

Control and stimulation tools (cat) for the PC modelers

International Nuclear Information System (INIS)

Chan, K.S.; Lea, K.C.

1990-01-01

For the last couple of years, the personal computer technology has received a steady stream of improvement in CPU processing power, fast floating coprocessor, super graphics to a very large and fast hard drive. Since Intel began shipping its 80386 version of CPU, it became practical to develop or execute a substantial amount of power plant software on a personal computer. With the introduction of the RISC type personal workstation, complete simulators based on these new generation of computers will soon become a reality. As of today, although almost anybody can afford a personal computer, simulation supporting software is still rare or non-existent at all. The CAST has been designed to support those users who want to develop or debug large power plant simulation programs on a personal computer or workstation. Another separate paper will also be presented to demonstrate the real world development and debugging tools offered by CAST

Data entry system for INIS input using a personal computer

International Nuclear Information System (INIS)

Ishikawa, Masashi

1990-01-01

Input preparation for the INIS (International Nuclear Information System) has been performed by Japan Atomic Energy Research Institute since 1970. Instead of the input data preparation done by worksheets make out with the typewriters, new method with which data can be directly inputted into a diskette using personal computers is introduced. According to the popularization of personal computers and word processors, this system is easily applied to other system, so the outline and the future development on it are described. A shortcoming of this system is that spell-checking and data entry using authority files are hardly performed because of the limitation of hardware resources, and that data code conversion is needed because applied code systems between personal computer and main frame computer are quite different from each other. On the other hand, improving the timelyness of data entry is expected without duplication of keying. (author)

Internationalization of healthcare applications: a generic approach for PACS workstations.

Science.gov (United States)

Hussein, R; Engelmann, U; Schroeter, A; Meinzer, H P

2004-01-01

Along with the revolution of information technology and the increasing use of computers world-wide, software providers recognize the emerging need for internationalized, or global, software applications. The importance of internationalization comes from its benefits such as addressing a broader audience, making the software applications more accessible, easier to use, more flexible to support and providing users with more consistent information. In addition, some governmental agencies, e.g., in Spain, accept only fully localized software. Although the healthcare communication standards, namely, Digital Imaging and Communication in Medicine (DICOM) and Health Level Seven (HL7) support wide areas of internationalization, most of the implementers are still protective about supporting the complex languages. This paper describes a generic internationalization approach for Picture Archiving and Communication System (PACS) workstations. The Unicode standard is used to internationalize the application user interface. An encoding converter was developed to encode and decode the data between the rendering module (in Unicode encoding) and the DICOM data (in ISO 8859 encoding). An integration gateway was required to integrate the internationalized PACS components with the different PACS installations. To introduce a pragmatic example, the described approach was applied to the CHILI PACS workstation. The approach has enabled the application to handle the different internationalization aspects transparently, such as supporting complex languages, switching between different languages at runtime, and supporting multilingual clinical reports. In the healthcare enterprises, internationalized applications play an essential role in supporting a seamless flow of information between the heterogeneous multivendor information systems.

Workstations as consoles for the CERN-PS complex, setting-up the environment

International Nuclear Information System (INIS)

Antonsanti, P.; Arruat, M.; Bouche, J.M.; Cons, L.; Deloose, Y.; Di Maio, F.

1992-01-01

Within the framework of the rejuvenation project of the CERN control systems, commercial workstations have to replace existing home-designed operator consoles. RISC-based workstations with UNIX, X-window TM and OSF/Motif TM have been introduced for the control of the PS complex. The first versions of general functionalities like synoptic display, program selection and control panels have been implemented and the first large scale application has been realized. This paper describes the different components of the workstation environment for the implementation of the applications. The focus is on the set of tools which have been used, developed or integrated, and on how we plan to make them evolve. (author)

XCOM: Photon cross sections on a personal computer

International Nuclear Information System (INIS)

Berger, M.J.; Hubbell, J.H.

1987-07-01

A computer program and data base are presented which can be used to calculate, with a personal computer, photon cross sections for scattering, photoelectric absorption and pair production, as well as total attenuation coefficients, in any element, compound or mixture, at energies from 1 keV to 100 GeV

Non-contact methods for NDT of aeronautical structures : An image processing workstation for thermography

OpenAIRE

Azzarelli, Luciano; Chimenti, Massimo; Salvetti, Ovidio

1992-01-01

The main goals of the Istituto di Elaborazione della Informazione in Task 4., Subtasks 4.3.1 (Image Processing) and 4.3.2 (Workstation Architecture) were the study of thermograms features, the design of the architecture of a customized workstation and the project of specialized algorithms for thermal image analysis. Thermograms features pertain to data acquisition, data archiving and data processing; following general study some basic requirements for the workstation were defined. "Data acqui...

Shoulder girdle muscle activity and fatigue in traditional and improved design carpet weaving workstations.

Science.gov (United States)

Allahyari, Teimour; Mortazavi, Narges; Khalkhali, Hamid Reza; Sanjari, Mohammad Ali

2016-01-01

Work-related musculoskeletal disorders in the neck and shoulder regions are common among carpet weavers. Working for prolonged hours in a static and awkward posture could result in an increased muscle activity and may lead to musculoskeletal disorders. Ergonomic workstation improvements can reduce muscle fatigue and the risk of musculoskeletal disorders. The aim of this study is to assess and to compare upper trapezius and middle deltoid muscle activity in 2 traditional and improved design carpet weaving workstations. These 2 workstations were simulated in a laboratory and 12 women carpet weavers worked for 3 h. Electromyography (EMG) signals were recorded during work in bilateral upper trapezius and bilateral middle deltoid. The root mean square (RMS) and median frequency (MF) values were calculated and used to assess muscle load and fatigue. Repeated measure ANOVA was performed to assess the effect of independent variables on muscular activity and fatigue. The participants were asked to report shoulder region fatigue on the Borg's Category-Ratio scale (Borg CR-10). Root mean square values in workstation A are significantly higher than in workstation B. Furthermore, EMG amplitude was higher in bilateral trapezius than in bilateral deltoid. However, muscle fatigue was not observed in any of the workstations. The results of the study revealed that muscle load in a traditional workstation was high, but fatigue was not observed. Further studies investigating other muscles involved in carpet weaving tasks are recommended. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Chemical emission rates from personal computers

DEFF Research Database (Denmark)

Nakagawa, T.; Wargocki, Pawel; Tanabe, S.

2003-01-01

Chemical emission measurements from different brands of personal computers (PCs) were conducted in a 1 m3 glass chamber. Eight PCs were tested individually. Each consisted of the same brand of PC tower and one of the 4 different brands of PC monitors. Within each brand both cathode-ray tube (CRT...

Energy-efficiency based classification of the manufacturing workstation

Science.gov (United States)

Frumuşanu, G.; Afteni, C.; Badea, N.; Epureanu, A.

2017-08-01

EU Directive 92/75/EC established for the first time an energy consumption labelling scheme, further implemented by several other directives. As consequence, nowadays many products (e.g. home appliances, tyres, light bulbs, houses) have an EU Energy Label when offered for sale or rent. Several energy consumption models of manufacturing equipments have been also developed. This paper proposes an energy efficiency - based classification of the manufacturing workstation, aiming to characterize its energetic behaviour. The concept of energy efficiency of the manufacturing workstation is defined. On this base, a classification methodology has been developed. It refers to specific criteria and their evaluation modalities, together to the definition & delimitation of energy efficiency classes. The energy class position is defined after the amount of energy needed by the workstation in the middle point of its operating domain, while its extension is determined by the value of the first coefficient from the Taylor series that approximates the dependence between the energy consume and the chosen parameter of the working regime. The main domain of interest for this classification looks to be the optimization of the manufacturing activities planning and programming. A case-study regarding an actual lathe classification from energy efficiency point of view, based on two different approaches (analytical and numerical) is also included.

Portable Computer Technology (PCT) Research and Development Program Phase 2

Science.gov (United States)

Castillo, Michael; McGuire, Kenyon; Sorgi, Alan

1995-01-01

The subject of this project report, focused on: (1) Design and development of two Advanced Portable Workstation 2 (APW 2) units. These units incorporate advanced technology features such as a low power Pentium processor, a high resolution color display, National Television Standards Committee (NTSC) video handling capabilities, a Personal Computer Memory Card International Association (PCMCIA) interface, and Small Computer System Interface (SCSI) and ethernet interfaces. (2) Use these units to integrate and demonstrate advanced wireless network and portable video capabilities. (3) Qualification of the APW 2 systems for use in specific experiments aboard the Mir Space Station. A major objective of the PCT Phase 2 program was to help guide future choices in computing platforms and techniques for meeting National Aeronautics and Space Administration (NASA) mission objectives. The focus being on the development of optimal configurations of computing hardware, software applications, and network technologies for use on NASA missions.

40 CFR 86.1312-2007 - Filter stabilization and microbalance workstation environmental conditions, microbalance...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Filter stabilization and microbalance workstation environmental conditions, microbalance specifications, and particulate matter filter handling and... Particulate Exhaust Test Procedures § 86.1312-2007 Filter stabilization and microbalance workstation...

Personal computer control system for small size tandem accelerator

Energy Technology Data Exchange (ETDEWEB)

Takayama, Hiroshi; Kawano, Kazuhiro; Shinozaki, Masataka [Nissin - High Voltage Co. Ltd., Kyoto (Japan)

1996-12-01

As the analysis apparatus using tandem accelerator has a lot of control parameter, numbers of control parts set on control panel are so many to make the panel more complex and its operativity worse. In order to improve these faults, development and design of a control system using personal computer for the control panel mainly constituted by conventional hardware parts were tried. Their predominant characteristics are shown as follows: (1) To make the control panel construction simpler and more compact, because the hardware device on the panel surface becomes the smallest limit as required by using a personal computer for man-machine interface. (2) To make control speed more rapid, because sequence control is closed within each block by driving accelerator system to each block and installing local station of the sequencer network at each block. (3) To make expandability larger, because of few improvement of the present hardware by interrupting the sequencer local station into the net and correcting image of the computer when increasing a new beamline. And, (4) to make control system cheaper, because of cheaper investment and easier programming by using the personal computer. (G.K.)

Computer assisted visualization of digital mammography images

International Nuclear Information System (INIS)

Funke, M.; Breiter, N.; Grabbe, E.; Netsch, T.; Biehl, M.; Peitgen, H.O.

1999-01-01

Purpose: In a clinical study, the feasibility of using a mammography workstation for the display and interpretation of digital mammography images was evaluated and the results were compared with the corresponding laser film hard copies. Materials and Methods: Digital phosphorous plate radiographs of the entire breast were obtained in 30 patients using a direct magnification mammography system. The images were displayed for interpretation on the computer monitor of a dedicated mammography workstation and also presented as laser film hard copies on a film view box for comparison. The images were evaluted with respect to the image handling, the image quality and the visualization of relevant structures by 3 readers. Results: Handling and contrast of the monitor displayed images were found to be superior compared with the film hard copies. Image noise was found in some cases but did not compromise the interpretation of the monitor images. The visualization of relevant structures was equal with both modalities. Altogether, image interpretation with the mammography workstation was considered to be easy, quick and confident. Conclusions: Computer-assisted visualization and interpretation of digital mammography images using a dedicated workstation can be performed with sufficiently high diagnostic accuracy. (orig.) [de

Distributed computing at the SSCL

International Nuclear Information System (INIS)

Cormell, L.; White, R.

1993-05-01

The rapid increase in the availability of high performance, cost- effective RISC/UNIX workstations has been both a blessing and a curse. The blessing of having extremely powerful computing engines available on the desk top is well-known to many users. The user has tremendous freedom, flexibility, and control of his environment. That freedom can, however, become the curse of distributed computing. The user must become a system manager to some extent, he must worry about backups, maintenance, upgrades, etc. Traditionally these activities have been the responsibility of a central computing group. The central computing group, however, may find that it can no linger provide all of the traditional services. With the plethora of workstations now found on so many desktops throughout the entire campus or lab, the central computing group may be swamped by support requests. This talk will address several of these computer support and management issues by discussing the approach taken at the Superconducting Super Collider Laboratory. In addition, a brief review of the future directions of commercial products for distributed computing and management will be given

Distributed computing at the SSCL

International Nuclear Information System (INIS)

Cormell, L.R.; White, R.C.

1994-01-01

The rapid increase in the availability of high performance, cost-effective RISC/UNIX workstations has been both a blessing and a curse. The blessing of having extremely powerful computing engines available on the desk top is well-known to many users. The user has tremendous freedom, flexibility, and control of his environment. That freedom can, however, become the curse of distributed computing. The user must become a system manager to some extent, he must worry about backups, maintenance, upgrades, etc. Traditionally these activities have been the responsibility of central computing group. The central computing group, however, may find that it can no longer provide all of the traditional services. With the plethora of workstations now found on so many desktops throughout the entire campus or lab, the central computing group may be swamped by support requests. This talk will address several of these computer support and management issues by discussing the approach taken at the Superconducting Super Collider Laboratory (SSCL). In addition, a brief review of the future directions of commercial products for distributed computing and management will be given

BioPhotonics Workstation: 3D interactive manipulation, observation and characterization

DEFF Research Database (Denmark)

Glückstad, Jesper

2011-01-01

In ppo.dk we have invented the BioPhotonics Workstation to be applied in 3D research on regulated microbial cell growth including their underlying physiological mechanisms, in vivo characterization of cell constituents and manufacturing of nanostructures and new materials.......In ppo.dk we have invented the BioPhotonics Workstation to be applied in 3D research on regulated microbial cell growth including their underlying physiological mechanisms, in vivo characterization of cell constituents and manufacturing of nanostructures and new materials....

Visualization of unsteady computational fluid dynamics

Science.gov (United States)

Haimes, Robert

1994-11-01

A brief summary of the computer environment used for calculating three dimensional unsteady Computational Fluid Dynamic (CFD) results is presented. This environment requires a super computer as well as massively parallel processors (MPP's) and clusters of workstations acting as a single MPP (by concurrently working on the same task) provide the required computational bandwidth for CFD calculations of transient problems. The cluster of reduced instruction set computers (RISC) is a recent advent based on the low cost and high performance that workstation vendors provide. The cluster, with the proper software can act as a multiple instruction/multiple data (MIMD) machine. A new set of software tools is being designed specifically to address visualizing 3D unsteady CFD results in these environments. Three user's manuals for the parallel version of Visual3, pV3, revision 1.00 make up the bulk of this report.

The impact of sit-stand office workstations on worker discomfort and productivity: a review.

Science.gov (United States)

Karakolis, Thomas; Callaghan, Jack P

2014-05-01

This review examines the effectiveness of sit-stand workstations at reducing worker discomfort without causing a decrease in productivity. Four databases were searched for studies on sit-stand workstations, and five selection criteria were used to identify appropriate articles. Fourteen articles were identified that met at least three of the five selection criteria. Seven of the identified studies reported either local, whole body or both local and whole body subjective discomfort scores. Six of these studies indicated implementing sit-stand workstations in an office environment led to lower levels of reported subjective discomfort (three of which were statistically significant). Therefore, this review concluded that sit-stand workstations are likely effective in reducing perceived discomfort. Eight of the identified studies reported a productivity outcome. Three of these studies reported an increase in productivity during sit-stand work, four reported no affect on productivity, and one reported mixed productivity results. Therefore, this review concluded that sit-stand workstations do not cause a decrease in productivity. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Workstation environment supports for startup of YGN 3 and 4 nuclear unit

International Nuclear Information System (INIS)

Lee, Won Jae; Kim, Won Bong; Lee, Byung Chae

1995-07-01

Light water reactor fuel development division of Korea Atomic Energy Research Institute participated in the installation of the plant computer system and software, and the user support activities of Asea Brown Boveri/Combustion Engineering for the Plant Monitoring System during the startup phase of YGN-3 nuclear unit. The main purpose of the participation is to have the self-reliant plant- computer technology for the independent design and startup of next nuclear units. This report describes the activities performed by KAERI with ABB/CE at the plant site. In addition, it describes the direct transfer of data files between PMS and workstation which was independently carried out by KAERI. Since KAERI should support the site in setting-up the plant computer environment independent of ABB-CE from the next nuclear units, the review was performed for the technical details of activities provided to the site in order to provide the better computer environment in the next nuclear units. In conclusion, this report is expected to provide the technical background for the supporting of plant computing environment and the scope of support work at plant site during Yonggwang 3, 4 startup in the area of plant computer for the next nuclear units. 6 refs. (Author) .new

Workstation environment supports for startup of YGN 3 and 4 nuclear unit

Energy Technology Data Exchange (ETDEWEB)

Lee, Won Jae; Kim, Won Bong; Lee, Byung Chae [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

Light water reactor fuel development division of Korea Atomic Energy Research Institute participated in the installation of the plant computer system and software, and the user support activities of Asea Brown Boveri/Combustion Engineering for the Plant Monitoring System during the startup phase of YGN-3 nuclear unit. The main purpose of the participation is to have the self-reliant plant- computer technology for the independent design and startup of next nuclear units. This report describes the activities performed by KAERI with ABB/CE at the plant site. In addition, it describes the direct transfer of data files between PMS and workstation which was independently carried out by KAERI. Since KAERI should support the site in setting-up the plant computer environment independent of ABB-CE from the next nuclear units, the review was performed for the technical details of activities provided to the site in order to provide the better computer environment in the next nuclear units. In conclusion, this report is expected to provide the technical background for the supporting of plant computing environment and the scope of support work at plant site during Yonggwang 3, 4 startup in the area of plant computer for the next nuclear units. 6 refs. (Author) .new.

Controlling Laboratory Processes From A Personal Computer

Science.gov (United States)

Will, H.; Mackin, M. A.

1991-01-01

Computer program provides natural-language process control from IBM PC or compatible computer. Sets up process-control system that either runs without operator or run by workers who have limited programming skills. Includes three smaller programs. Two of them, written in FORTRAN 77, record data and control research processes. Third program, written in Pascal, generates FORTRAN subroutines used by other two programs to identify user commands with device-driving routines written by user. Also includes set of input data allowing user to define user commands to be executed by computer. Requires personal computer operating under MS-DOS with suitable hardware interfaces to all controlled devices. Also requires FORTRAN 77 compiler and device drivers written by user.

ISDN communication: Its workstation technology and application system

Energy Technology Data Exchange (ETDEWEB)

Sugimura, T; Ogiwara, Y; Saito, T [Hitachi, Ltd., Tokyo (Japan)

1991-07-01

This report describes technology for integrated services digital network (ISDN) which allows workstations to process multimedia data and application systems of advanced group teleworking which use such technology. Hitachi has developed workstations which are more powerful, have more functions, and have larger memory capacities. These factors allowed media which require high-speed processing of large quantities of voice and image data to be integrated into the world of conventional text data processing and communications. In addition, the application of group teleworking system has a large impact through the improvements in the office environment, the changes in the style of office work, and the appearance of new businesses. A prototype of this system was exhibited and demonstrated at TELECOM91. 1 ref., 4 figs., 2 tabs.

Computing farms

International Nuclear Information System (INIS)

Yeh, G.P.

2000-01-01

High-energy physics, nuclear physics, space sciences, and many other fields have large challenges in computing. In recent years, PCs have achieved performance comparable to the high-end UNIX workstations, at a small fraction of the price. We review the development and broad applications of commodity PCs as the solution to CPU needs, and look forward to the important and exciting future of large-scale PC computing

Virtual interface environment workstations

Science.gov (United States)

Fisher, S. S.; Wenzel, E. M.; Coler, C.; Mcgreevy, M. W.

1988-01-01

A head-mounted, wide-angle, stereoscopic display system controlled by operator position, voice and gesture has been developed at NASA's Ames Research Center for use as a multipurpose interface environment. This Virtual Interface Environment Workstation (VIEW) system provides a multisensory, interactive display environment in which a user can virtually explore a 360-degree synthesized or remotely sensed environment and can viscerally interact with its components. Primary applications of the system are in telerobotics, management of large-scale integrated information systems, and human factors research. System configuration, research scenarios, and research directions are described.

[Use of personal computers by diplomats of anesthesiology in Japan].

Science.gov (United States)

Yamamoto, K; Ohmura, S; Tsubokawa, T; Kita, M; Kushida, Y; Kobayashi, T

1999-04-01

Use of personal computers by diplomats of the Japanese Board of Anesthesiology working in Japanese university hospitals was investigated. Unsigned questionnaires were returned from 232 diplomats of 18 anesthesia departments. The age of responders ranged from twenties to sixties. Personal computer systems are used by 223 diplomats (96.1%), while nine (3.9%) do not use them. The computer systems used are: Apple Macintosh 77%, IBM compatible PC 21% and UNIX 2%. Although 197 diplomats have e-mail addresses, only 162 of them actually send and receive e-mails. Diplomats in fifties use e-mail most actively and those in sixties come second.

Test-retest reliability and concurrent validity of a web-based questionnaire measuring workstation and individual correlates of work postures during computer work

NARCIS (Netherlands)

IJmker, S.; Mikkers, J.; Blatter, B.M.; Beek, A.J. van der; Mechelen, W. van; Bongers, P.M.

2008-01-01

Introduction: "Ergonomic" questionnaires are widely used in epidemiological field studies to study the association between workstation characteristics, work posture and musculoskeletal disorders among office workers. Findings have been inconsistent regarding the putative adverse effect of work

Effect of One Carpet Weaving Workstation on Upper Trapezius Fatigue

Directory of Open Access Journals (Sweden)

Neda Mahdavi

2016-03-01

Full Text Available Introduction: This study aimed to investigate the effect of carpet weaving at a proposed workstation on Upper Trapezius (UTr fatigue during a task cycle. Fatigue in the shoulder is one of the most important precursors for upper limb musculoskeletal disorders. One of the most prevalent musculoskeletal disorders between carpet weavers is disorder of the shoulder region. Methods: This cross-sectional study, included eight females and three males. During an 80-minute cycle of carpet weaving, Electromyography (EMG signals of right and left UTr were recorded by the surface EMG, continuously. After raw signals were processed, MPF and RMS were considered as EMG amplitude and frequency parameters. Time series model and JASA methods were used to assess and classify the EMG parameter changes during the working time. Results: According to the JASA method, 58%, 16%, 8% and 8% of the participants experienced fatigue, force increase, force decrease and recovery, respectively in the right UTr. Also, 50%, 25%, 8% and 16% of the participants experienced fatigue, force increase, force decrease and recovery, respectively in the left UTr. Conclusions: For the major portion of the weavers, dominant status in Left and right UTr was fatigue, at the proposed workstation during a carpet weaving task cycle. The results of the study provide detailed information for optimal design of workstations. Further studies should focus on fatigue in various muscles and time periods for designing an appropriate and ergonomics carpet weaving workstation

Personalization and perceived personal relevance in computer-tailored persuasion in smoking cessation.

Science.gov (United States)

Dijkstra, Arie; Ballast, Karien

2012-02-01

In most computer-tailored interventions, the recipient's name is used to personalize the information. This is done to increase the process of persuasion but few empirical data exist that support this notion. An experimental laboratory study was conducted to test the effects of mentioning the participants name and to study whether it was related to the depth of processing in a 2 (personalization/standard) × 2 (weak/strong arguments) design. Over 120 student smokers were randomly assigned to one of the four experimental conditions in which they read smoking cessation messages offering (pre-tested) strong or weak arguments. Personalization was applied by mentioning the recipient's first name three times in the text. The intention to quit smoking was the dependent variable. Personalization increased persuasion when perceived personal relevance was high, but it decreased persuasion when perceived personal relevance was low. The effects on persuasion were only present in the case of strong arguments. Personalization is not always effective, and it may even lead to less persuasion. Therefore, this often used way to tailor messages must be applied with care. ©2011 The British Psychological Society.

Transforming creativity: Personalized manufacturing meets embodied computing

Directory of Open Access Journals (Sweden)

Alan B. Craig

2012-06-01

Full Text Available This paper discusses aspects of a collaborative investigation of embodied computing and personal manufacturing. We describe the NeuroMaker 1.0, an artwork that playfully implements the concept of “translating of the designer’s ideas into a product”. Visitors to the installation were invited to use their own EEG to fabricate personalized physical objects. While primarily intended to provoke thought about the process of creativity, we also demonstrated that, with the right team, radical new interfaces are well within the reach.

A pilot study of change in cerebral activity during personality rating by questionnaire and personal computer.

Science.gov (United States)

Sato, Emi; Matsuda, Kouhei

2018-06-11

The purpose of this study was to examine cerebral blood flow in the frontal cortex area during personality self-rating tasks. Our two hypotheses were (1) cerebral blood flow varies based on personality rating condition and (2) cerebral blood flow varies based on the personality traits. This experiment measured cerebral blood flow under 3 personal computer rating conditions and 2 questionnaire conditions. Comparing the rating conditions, the results of the t-test indicated that cerebral blood flow was higher in the questionnaire condition than it was in the personal computer condition. With respect to the Big Five, the result of the correlation coefficient, that is, cerebral blood flow during a personality rating task, changed according to the trait for agreeableness. The results of the analysis of the 5-cluster on individual differences indicated that certain personality traits were related to the factors that increased or decreased cerebral blood flow. An analysis of variance indicated that openness to experience and Behavioural Activation System-drive was significant given that participants with high intellectual curiosity were motivated in this experiment, thus, their cerebral blood flow may have increased. The significance of this experiment was that by employing certain performance measures we could examine differences in physical changes based on personality traits. © 2018 International Union of Psychological Science.

The Influence of Personal Characteristics, Interaction: (Computer/Individual), Computer Self-efficacy, Personal Innovativeness in Information Technology to Computer Anxiety in use of Mind your Own Business Accounting Software

OpenAIRE

Mayasari, Mega; ., Gudono

2015-01-01

The purpose of this study was to identify the factors that cause computer anxiety in the use of Mind Your Own Business (MYOB) accounting software, i.e., to assess if there are any influence of age, gender, amount of training, ownership (usage of accounting software on a regular basis), computer self-efficacy, personal innovativeness in Information Technology (IT) to computer anxiety. The study also examined whether there is a relationship trait anxiety and negative affect to computer self-eff...

76 FR 10403 - Hewlett Packard (HP), Global Product Development, Engineering Workstation Refresh Team, Working...

Science.gov (United States)

2011-02-24

...), Global Product Development, Engineering Workstation Refresh Team, Working On-Site at General Motors..., Non-Information Technology Business Development Team and Engineering Application Support Team, working... Hewlett Packard, Global Product Development, Engineering Workstation Refresh Team, working on-site at...

Computer systems in the operation, maintenance and technical support of Loviisa NPS

International Nuclear Information System (INIS)

Tiitinen, M.

1993-01-01

A description is given of how the Loviisa nuclear power plant has utilized computers in many ways in the operation, maintenance, technical support and in other functions at the plant. The evolution of the computer system can be divided into the following phases: plant commissioning (1975-80), maintenance systems development (1981-84), second generation systems take-over (1985-90) and workstation client/server systems and PC's proliferation (1991->). A short description is given of the main systems at the Loviisa plant using computers, i.e. process computer systems, the plant information system, training simulator, vibration monitoring, laboratory computer systems, PC and workstation applications. (Z.S.) 4 refs

MULTI - multifunctional interface of the IBM XT and AT type personal computers

International Nuclear Information System (INIS)

Gross, T.; Kalavski, D.; Rubin, D.; Tulaev, A.B.; Tumanov, A.V.

1988-01-01

MULTI multifunctional interface which enables to solve problems of personal computer connestion with physical equipment without application of intermediate buses is described. Parallel 32-digit bidirectional 1/10 register and buffered bus of personal computer represent MULTI base. Ways of MULTI application are described

A nuclear power plant system engineering workstation

International Nuclear Information System (INIS)

Mason, J.H.; Crosby, J.W.

1989-01-01

System engineers offer an approach for effective technical support for operation and maintenance of nuclear power plants. System engineer groups are being set up by most utilities in the United States. Institute of Nuclear Power operations (INPO) and U.S. Nuclear Regulatory Commission (NRC) have endorsed the concept. The INPO Good Practice and a survey of system engineer programs in the southeastern United States provide descriptions of system engineering programs. The purpose of this paper is to describe a process for developing a design for a department-level information network of workstations for system engineering groups. The process includes the following: (1) application of a formal information engineering methodology, (2) analysis of system engineer functions and activities; (3) use of Electric Power Research Institute (EPRI) Plant Information Network (PIN) data; (4) application of the Information Engineering Workbench. The resulting design for this system engineer workstation can provide a reference for design of plant-specific systems

[Three dimensional CT reconstruction system on a personal computer].

Science.gov (United States)

Watanabe, E; Ide, T; Teramoto, A; Mayanagi, Y

1991-03-01

A new computer system to produce three dimensional surface image from CT scan has been invented. Although many similar systems have been already developed and reported, they are too expensive to be set up in routine clinical services because most of these systems are based on high power mini-computer systems. According to the opinion that a practical 3D-CT system should be used in daily clinical activities using only a personal computer, we have transplanted the 3D program into a personal computer working in MS-DOS (16-bit, 12 MHz). We added to the program a routine which simulates surgical dissection on the surface image. The time required to produce the surface image ranges from 40 to 90 seconds. To facilitate the simulation, we connected a 3D system with the neuronavigator. The navigator gives the position of the surgical simulation when the surgeon places the navigator tip on the patient's head thus simulating the surgical excision before the real dissection.

Diagnostic image workstations ofr PACS

International Nuclear Information System (INIS)

Meyer-Ebrecht, D.; Fasel, B.; Dahm, M.; Kaupp, A.; Schilling, R.

1990-01-01

Image workstations will be the 'window' to the complex infrastructure of PACS with its intertwined image modalities (image sources, image data bases and image processing devices) and data processing modalities (patient data bases, departmental and hospital information systems). They will serve for user-to-system dialogues, image display and local processing of data as well as images. Their hardware and software structures have to be optimized towards an efficient throughput and processing of image data. (author). 10 refs

Next Genertation BioPhotonics Workstation

DEFF Research Database (Denmark)

Bañas, Andrew Rafael; Palima, Darwin; Tauro, Sandeep

We will outline the specs of our Biophotonics Workstation that can generate up to 100 reconfigurable laser-traps making 3D real-time optical manipulation of advanced structures, cells or tiny particles possible with the use of joysticks or gaming devices. Optically actuated nanoneedles may...... be functionalized or directly used to perforate targeted cells at specific locations or force the complete separation of dividing cells, among other functions that can be very useful for microbiologists or biomedical researchers....

Assessment of a cooperative workstation.

OpenAIRE

Beuscart, R. J.; Molenda, S.; Souf, N.; Foucher, C.; Beuscart-Zephir, M. C.

1996-01-01

Groupware and new Information Technologies have now made it possible for people in different places to work together in synchronous cooperation. Very often, designers of this new type of software are not provided with a model of the common workspace, which is prejudicial to software development and its acceptance by potential users. The authors take the example of a task of medical co-diagnosis, using a multi-media communication workstation. Synchronous cooperative work is made possible by us...

Viewport: An object-oriented approach to integrate workstation software for tile and stack mode display

OpenAIRE

Ghosh, Srinka; Andriole, Katherine P.; Avrin, David E.

1997-01-01

Diagnostic workstation design has migrated towards display presentation in one of two modes: tiled images or stacked images. It is our impression that the workstation setup or configuration in each of these two modes is rather distinct. We sought to establish a commonality to simplify software design, and to enable a single descriptor method to facilitate folder manager development of “hanging” protocols. All current workstation designs use a combination of “off-screen” and “on-screen” memory...

Applications of the parallel computing system using network

International Nuclear Information System (INIS)

Ido, Shunji; Hasebe, Hiroki

1994-01-01

Parallel programming is applied to multiple processors connected in Ethernet. Data exchanges between tasks located in each processing element are realized by two ways. One is socket which is standard library on recent UNIX operating systems. Another is a network connecting software, named as Parallel Virtual Machine (PVM) which is a free software developed by ORNL, to use many workstations connected to network as a parallel computer. This paper discusses the availability of parallel computing using network and UNIX workstations and comparison between specialized parallel systems (Transputer and iPSC/860) in a Monte Carlo simulation which generally shows high parallelization ratio. (author)

Personalization and perceived personal relevance in computer-tailored persuasion in smoking cessation

NARCIS (Netherlands)

Dijkstra, Arie; Ballast, Karien

Objectives. In most computer-tailored interventions, the recipient's name is used to personalize the information. This is done to increase the process of persuasion but few empirical data exist that support this notion. yDesign. An experimental laboratory study was conducted to test the effects of

Geometric data perturbation-based personal health record transactions in cloud computing.

Science.gov (United States)

Balasubramaniam, S; Kavitha, V

2015-01-01

Cloud computing is a new delivery model for information technology services and it typically involves the provision of dynamically scalable and often virtualized resources over the Internet. However, cloud computing raises concerns on how cloud service providers, user organizations, and governments should handle such information and interactions. Personal health records represent an emerging patient-centric model for health information exchange, and they are outsourced for storage by third parties, such as cloud providers. With these records, it is necessary for each patient to encrypt their own personal health data before uploading them to cloud servers. Current techniques for encryption primarily rely on conventional cryptographic approaches. However, key management issues remain largely unsolved with these cryptographic-based encryption techniques. We propose that personal health record transactions be managed using geometric data perturbation in cloud computing. In our proposed scheme, the personal health record database is perturbed using geometric data perturbation and outsourced to the Amazon EC2 cloud.

Geometric Data Perturbation-Based Personal Health Record Transactions in Cloud Computing

Science.gov (United States)

Balasubramaniam, S.; Kavitha, V.

2015-01-01

Cloud computing is a new delivery model for information technology services and it typically involves the provision of dynamically scalable and often virtualized resources over the Internet. However, cloud computing raises concerns on how cloud service providers, user organizations, and governments should handle such information and interactions. Personal health records represent an emerging patient-centric model for health information exchange, and they are outsourced for storage by third parties, such as cloud providers. With these records, it is necessary for each patient to encrypt their own personal health data before uploading them to cloud servers. Current techniques for encryption primarily rely on conventional cryptographic approaches. However, key management issues remain largely unsolved with these cryptographic-based encryption techniques. We propose that personal health record transactions be managed using geometric data perturbation in cloud computing. In our proposed scheme, the personal health record database is perturbed using geometric data perturbation and outsourced to the Amazon EC2 cloud. PMID:25767826

Geometric Data Perturbation-Based Personal Health Record Transactions in Cloud Computing

Directory of Open Access Journals (Sweden)

S. Balasubramaniam

2015-01-01

Full Text Available Cloud computing is a new delivery model for information technology services and it typically involves the provision of dynamically scalable and often virtualized resources over the Internet. However, cloud computing raises concerns on how cloud service providers, user organizations, and governments should handle such information and interactions. Personal health records represent an emerging patient-centric model for health information exchange, and they are outsourced for storage by third parties, such as cloud providers. With these records, it is necessary for each patient to encrypt their own personal health data before uploading them to cloud servers. Current techniques for encryption primarily rely on conventional cryptographic approaches. However, key management issues remain largely unsolved with these cryptographic-based encryption techniques. We propose that personal health record transactions be managed using geometric data perturbation in cloud computing. In our proposed scheme, the personal health record database is perturbed using geometric data perturbation and outsourced to the Amazon EC2 cloud.

Physics analysis workstation

International Nuclear Information System (INIS)

Johnstad, H.

1989-06-01

The Physics Analysis Workstation (PAW) is a high-level program providing data presentation and statistical or mathematical analysis. PAW has been developed at CERN as an instrument to assist physicists in the analysis and presentation of their data. The program is interfaced to a high level graphics package, based on basic underlying graphics. 3-D graphics capabilities are being implemented. The major objects in PAW are 1 or 2 dimensional binned event data with fixed number of entries per event, vectors, functions, graphics pictures, and macros. Command input is handled by an integrated user interface package, which allows for a variety of choices for input, either with typed commands, or in a tree structure menu driven mode. 6 refs., 1 fig

An open architecture for medical image workstation

Science.gov (United States)

Liang, Liang; Hu, Zhiqiang; Wang, Xiangyun

2005-04-01

Dealing with the difficulties of integrating various medical image viewing and processing technologies with a variety of clinical and departmental information systems and, in the meantime, overcoming the performance constraints in transferring and processing large-scale and ever-increasing image data in healthcare enterprise, we design and implement a flexible, usable and high-performance architecture for medical image workstations. This architecture is not developed for radiology only, but for any workstations in any application environments that may need medical image retrieving, viewing, and post-processing. This architecture contains an infrastructure named Memory PACS and different kinds of image applications built on it. The Memory PACS is in charge of image data caching, pre-fetching and management. It provides image applications with a high speed image data access and a very reliable DICOM network I/O. In dealing with the image applications, we use dynamic component technology to separate the performance-constrained modules from the flexibility-constrained modules so that different image viewing or processing technologies can be developed and maintained independently. We also develop a weakly coupled collaboration service, through which these image applications can communicate with each other or with third party applications. We applied this architecture in developing our product line and it works well. In our clinical sites, this architecture is applied not only in Radiology Department, but also in Ultrasonic, Surgery, Clinics, and Consultation Center. Giving that each concerned department has its particular requirements and business routines along with the facts that they all have different image processing technologies and image display devices, our workstations are still able to maintain high performance and high usability.

Speed up of MCACE, a Monte Carlo code for evaluation of shielding safety, by parallel computer, (3)

International Nuclear Information System (INIS)

Takano, Makoto; Masukawa, Fumihiro; Naito, Yoshitaka; Onodera, Emi; Imawaka, Tsuneyuki; Yoda, Yoshihisa.

1993-07-01

The parallel computing of the MCACE code has been studied on two platforms; 1) Shared Memory Type Vector-Parallel Computer Monte-4 and 2) Networked Several Workstations. On the Monte-4, a disk-file has been allocated to collect all results computed by 4 CPUs in parallel, executing the copy of the MCACE code on each CPU. On the workstations under network environment, two parallel models have been evaluated; 1) a host-node model and 2) the model used on the Monte-4 where no software for parallelization has been employed but only standard FORTRAN language. The measurement of computing times has showed that speed up of about 3 times has been achieved by using 4 CPUs of the Monte-4. Further, connecting 4 workstations by network, the computing speed by parallelization has achieved faster than our scalar main frame computer, FACOM M-780. (author)

Computed Tomography (CT) -- Sinuses

Medline Plus

Full Text Available ... diagnose sinusitis . evaluate sinuses that are filled with fluid or thickened sinus membranes . detect the presence of ... other in a ring, called a gantry. The computer workstation that processes the imaging information is located ...

Distributed computing feasibility in a non-dedicated homogeneous distributed system

Science.gov (United States)

Leutenegger, Scott T.; Sun, Xian-He

1993-01-01

The low cost and availability of clusters of workstations have lead researchers to re-explore distributed computing using independent workstations. This approach may provide better cost/performance than tightly coupled multiprocessors. In practice, this approach often utilizes wasted cycles to run parallel jobs. The feasibility of such a non-dedicated parallel processing environment assuming workstation processes have preemptive priority over parallel tasks is addressed. An analytical model is developed to predict parallel job response times. Our model provides insight into how significantly workstation owner interference degrades parallel program performance. A new term task ratio, which relates the parallel task demand to the mean service demand of nonparallel workstation processes, is introduced. It was proposed that task ratio is a useful metric for determining how large the demand of a parallel applications must be in order to make efficient use of a non-dedicated distributed system.

Parallel computing for event reconstruction in high-energy physics

International Nuclear Information System (INIS)

Wolbers, S.

1993-01-01

Parallel computing has been recognized as a solution to large computing problems. In High Energy Physics offline event reconstruction of detector data is a very large computing problem that has been solved with parallel computing techniques. A review of the parallel programming package CPS (Cooperative Processes Software) developed and used at Fermilab for offline reconstruction of Terabytes of data requiring the delivery of hundreds of Vax-Years per experiment is given. The Fermilab UNIX farms, consisting of 180 Silicon Graphics workstations and 144 IBM RS6000 workstations, are used to provide the computing power for the experiments. Fermilab has had a long history of providing production parallel computing starting with the ACP (Advanced Computer Project) Farms in 1986. The Fermilab UNIX Farms have been in production for over 2 years with 24 hour/day service to experimental user groups. Additional tools for management, control and monitoring these large systems will be described. Possible future directions for parallel computing in High Energy Physics will be given

Finite elements as an integrated part of Computer-Aided-Engineering (CAE)

International Nuclear Information System (INIS)

Groth, P.; Kammerer, R.

1986-01-01

The prerequisites for software will be demonstrated using a standard interface for embedding FEM in a CAE system. The realization of a powerful system concept with workstations and personal computers tied to host computers will be presented together with colour graphic terminals for result display. As a standard interface the usage of IGES for the transfer of geometrical data from the CAD system to the FEM preprocessor will be discussed along with the possibilities of usage for new designs and variations for 2D and 3D tasks. In the sectors of pre- and postprocessors a proposal for standardizing the interfaces Pre/FEM, FEM/Post as well as FEM/FEM will be presented (working title FEDIS). The entire problematics will be illustrated by practical examples from mechanical industry and plant design. (orig.)

76 FR 71980 - SEDASYS Computer-Assisted Personalized Sedation System; Ethicon Endo-Surgery, Incorporated's...

Science.gov (United States)

2011-11-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-P-0176] SEDASYS Computer-Assisted Personalized Sedation System; Ethicon Endo-Surgery, Incorporated's Petition for... SEDASYS computer-assisted personalized sedation system (SEDASYS) submitted by Ethicon Endo-Surgery Inc...

Heat exchanger performance analysis programs for the personal computer

International Nuclear Information System (INIS)

Putman, R.E.

1992-01-01

Numerous utility industry heat exchange calculations are repetitive and thus lend themselves to being performed on a Personal Computer. These programs may be regarded as engineering tools which, when put together, can form a Toolbox. However, the practicing Results Engineer in the utility industry desires not only programs that are robust as well as easy to use but can also be used both on desktop and laptop PC's. The latter also offer the opportunity to take the computer into the plant or control room, and use it there to process test or operating data right on the spot. Most programs evolve through the needs which arise in the course of day-to-day work. This paper describes several of the more useful programs of this type and outlines some of the guidelines to be followed when designing personal computer programs for use by the practicing Results Engineer

Personal computer wallpaper user segmentation based on Sasang typology.

Science.gov (United States)

Lee, Joung-Youn

2015-03-01

As human-computer interaction (HCI) is becoming a significant part of all human life, the user's emotional satisfaction is an important factor to consider. These changes have been pointed out by several researchers who claim that a user's personality may become the most important factor in the design. The objective of this study is to examine Sasang typology as a user segmentation method in the area of HCI design. To test HCI usage patterns in terms of the user's personality and temperament, this study focuses on personal computer (PC) or lap-top wallpaper settings. One hundred and four Facebook friends completed a QSCC II survey assessing Sasang typology type and sent a captured image of their personal PC or lap-top wallpaper. To classify the computer usage pattern, folder organization and wallpaper setting were investigated. The research showed that So-Yang type organized folders and icons in an orderly manner, whereas So-Eum type did not organize folders and icons at all. With regard to wallpaper settings, So-Yang type used the default wallpaper provided by the PC but So-Eum type used landscape images. Because So-Yang type was reported to be emotionally stable and extrovert, they tended to be highly concerned with online privacy compared with So-Eum type. So-Eum type use a lot of images of landscapes as the background image, which demonstrates So-Eum's low emotional stability, anxiety, and the desire to obtain analogy throughout the computer screen. Also, So-Yang's wallpapers display family or peripheral figures and this is due to the sociability that extrovert So-Yang types possess. By proposing the Sasang typology as a factor in influencing an HCI usage pattern in this study, it can be used to predict the user's HCI experience, or suggest a native design methodology that can actively cope with the user's psychological environment.

BioPhotonics Workstation: a university tech transfer challenge

DEFF Research Database (Denmark)

Glückstad, Jesper; Bañas, Andrew Rafael; Tauro, Sandeep

2011-01-01

Conventional optical trapping or tweezing is often limited in the achievable trapping range because of high numerical aperture and imaging requirements. To circumvent this, we are developing a next generation BioPhotonics Workstation platform that supports extension modules through a long working...

Iterative solution of general sparse linear systems on clusters of workstations

Energy Technology Data Exchange (ETDEWEB)

Lo, Gen-Ching; Saad, Y. [Univ. of Minnesota, Minneapolis, MN (United States)

1996-12-31

Solving sparse irregularly structured linear systems on parallel platforms poses several challenges. First, sparsity makes it difficult to exploit data locality, whether in a distributed or shared memory environment. A second, perhaps more serious challenge, is to find efficient ways to precondition the system. Preconditioning techniques which have a large degree of parallelism, such as multicolor SSOR, often have a slower rate of convergence than their sequential counterparts. Finally, a number of other computational kernels such as inner products could ruin any gains gained from parallel speed-ups, and this is especially true on workstation clusters where start-up times may be high. In this paper we discuss these issues and report on our experience with PSPARSLIB, an on-going project for building a library of parallel iterative sparse matrix solvers.

Computer-based, personalized cognitive training versus classical computer games: a randomized double-blind prospective trial of cognitive stimulation.

Science.gov (United States)

Peretz, Chava; Korczyn, Amos D; Shatil, Evelyn; Aharonson, Vered; Birnboim, Smadar; Giladi, Nir

2011-01-01

Many studies have suggested that cognitive training can result in cognitive gains in healthy older adults. We investigated whether personalized computerized cognitive training provides greater benefits than those obtained by playing conventional computer games. This was a randomized double-blind interventional study. Self-referred healthy older adults (n = 155, 68 ± 7 years old) were assigned to either a personalized, computerized cognitive training or to a computer games group. Cognitive performance was assessed at baseline and after 3 months by a neuropsychological assessment battery. Differences in cognitive performance scores between and within groups were evaluated using mixed effects models in 2 approaches: adherence only (AO; n = 121) and intention to treat (ITT; n = 155). Both groups improved in cognitive performance. The improvement in the personalized cognitive training group was significant (p computer games group it was significant (p games in improving visuospatial working memory (p = 0.0001), visuospatial learning (p = 0.0012) and focused attention (p = 0.0019). Personalized, computerized cognitive training appears to be more effective than computer games in improving cognitive performance in healthy older adults. Further studies are needed to evaluate the ecological validity of these findings. Copyright © 2011 S. Karger AG, Basel.

Personal computer based home automation system

OpenAIRE

Hellmuth, George F.

1993-01-01

The systems engineering process is applied in the development of the preliminary design of a home automation communication protocol. The objective of the communication protocol is to provide a means for a personal computer to communicate with adapted appliances in the home. A needs analysis is used to ascertain that a need exist for a home automation system. Numerous design alternatives are suggested and evaluated to determine the best possible protocol design. Coaxial cable...

Post-deployment usability evaluation of a radiology workstation

NARCIS (Netherlands)

Jorritsma, Wiard; Cnossen, Fokie; Dierckx, Rudi; Oudkerk, Matthijs; van Ooijen, Peter

2015-01-01

Objective To evaluate the usability of a radiology workstation after deployment in a hospital. Significance In radiology, it is difficult to perform valid pre-deployment usability evaluations due to the heterogeneity of the user group, the complexity of the radiological workflow, and the complexity

Interpretation of digital breast tomosynthesis: preliminary study on comparison with picture archiving and communication system (PACS) and dedicated workstation.

Science.gov (United States)

Kim, Young Seon; Chang, Jung Min; Yi, Ann; Shin, Sung Ui; Lee, Myung Eun; Kim, Won Hwa; Cho, Nariya; Moon, Woo Kyung

2017-08-01

To compare the diagnostic accuracy and efficiency in the interpretation of digital breast tomosynthesis (DBT) images using a picture archiving and communication system (PACS) and a dedicated workstation. 97 DBT images obtained for screening or diagnostic purposes were stored in both a workstation and a PACS and evaluated in combination with digital mammography by three independent radiologists retrospectively. Breast Imaging-Reporting and Data System final assessments and likelihood of malignancy (%) were assigned and the interpretation time when using the workstation and PACS was recorded. Receiver operating characteristic curve analysis, sensitivities and specificities were compared with histopathological examination and follow-up data as a reference standard. Area under the receiver operating characteristic curve values for cancer detection (0.839 vs 0.815, p = 0.6375) and sensitivity (81.8% vs 75.8%, p = 0.2188) showed no statistically significant differences between the workstation and PACS. However, specificity was significantly higher when analysing on the workstation than when using PACS (83.7% vs 76.9%, p = 0.009). When evaluating DBT images using PACS, only one case was deemed necessary to be reanalysed using the workstation. The mean time to interpret DBT images on PACS (1.68 min/case) was significantly longer than that to interpret on the workstation (1.35 min/case) (p < 0.0001). Interpretation of DBT images using PACS showed comparable diagnostic performance to a dedicated workstation, even though it required a longer reading time. Advances in knowledge: Interpretation of DBT images using PACS is an alternative to evaluate the images when a dedicated workstation is not available.

Co-occurrence of addictive behaviours: personality factors related to substance use, gambling and computer gaming.

Science.gov (United States)

Walther, Birte; Morgenstern, Matthis; Hanewinkel, Reiner

2012-01-01

To investigate co-occurrence and shared personality characteristics of problematic computer gaming, problematic gambling and substance use. Cross-sectional survey data were collected from 2,553 German students aged 12-25 years. Self-report measures of substance use (alcohol, tobacco and cannabis), problematic gambling (South Oaks Gambling Screen - Revised for Adolescents, SOGS-RA), problematic computer gaming (Video Game Dependency Scale, KFN-CSAS-II), and of twelve different personality characteristics were obtained. Analyses revealed positive correlations between tobacco, alcohol and cannabis use and a smaller positive correlation between problematic gambling and problematic computer gaming. Problematic computer gaming co-occurred only with cannabis use, whereas problematic gambling was associated with all three types of substance use. Multivariate multilevel analyses showed differential patterns of personality characteristics. High impulsivity was the only personality characteristic associated with all five addictive behaviours. Depression and extraversion were specific to substance users. Four personality characteristics were specifically associated with problematic computer gaming: irritability/aggression, social anxiety, ADHD, and low self-esteem. Problematic gamblers seem to be more similar to substance users than problematic computer gamers. From a personality perspective, results correspond to the inclusion of gambling in the same DSM-V category as substance use and question a one-to-one proceeding for computer gaming. Copyright © 2012 S. Karger AG, Basel.

Workplace sitting and height-adjustable workstations: a randomized controlled trial.

Science.gov (United States)

Neuhaus, Maike; Healy, Genevieve N; Dunstan, David W; Owen, Neville; Eakin, Elizabeth G

2014-01-01

Desk-based office employees sit for most of their working day. To address excessive sitting as a newly identified health risk, best practice frameworks suggest a multi-component approach. However, these approaches are resource intensive and knowledge about their impact is limited. To compare the efficacy of a multi-component intervention to reduce workplace sitting time, to a height-adjustable workstations-only intervention, and to a comparison group (usual practice). Three-arm quasi-randomized controlled trial in three separate administrative units of the University of Queensland, Brisbane, Australia. Data were collected between January and June 2012 and analyzed the same year. Desk-based office workers aged 20-65 (multi-component intervention, n=16; workstations-only, n=14; comparison, n=14). The multi-component intervention comprised installation of height-adjustable workstations and organizational-level (management consultation, staff education, manager e-mails to staff) and individual-level (face-to-face coaching, telephone support) elements. Workplace sitting time (minutes/8-hour workday) assessed objectively via activPAL3 devices worn for 7 days at baseline and 3 months (end-of-intervention). At baseline, the mean proportion of workplace sitting time was approximately 77% across all groups (multi-component group 366 minutes/8 hours [SD=49]; workstations-only group 373 minutes/8 hours [SD=36], comparison 365 minutes/8 hours [SD=54]). Following intervention and relative to the comparison group, workplace sitting time in the multi-component group was reduced by 89 minutes/8-hour workday (95% CI=-130, -47 minutes; pworkplace sitting. These findings may have important practical and financial implications for workplaces targeting sitting time reductions. Australian New Zealand Clinical Trials Registry 00363297. © 2013 American Journal of Preventive Medicine Published by American Journal of Preventive Medicine All rights reserved.

A scalable approach to modeling groundwater flow on massively parallel computers

International Nuclear Information System (INIS)

Ashby, S.F.; Falgout, R.D.; Tompson, A.F.B.

1995-12-01

We describe a fully scalable approach to the simulation of groundwater flow on a hierarchy of computing platforms, ranging from workstations to massively parallel computers. Specifically, we advocate the use of scalable conceptual models in which the subsurface model is defined independently of the computational grid on which the simulation takes place. We also describe a scalable multigrid algorithm for computing the groundwater flow velocities. We axe thus able to leverage both the engineer's time spent developing the conceptual model and the computing resources used in the numerical simulation. We have successfully employed this approach at the LLNL site, where we have run simulations ranging in size from just a few thousand spatial zones (on workstations) to more than eight million spatial zones (on the CRAY T3D)-all using the same conceptual model

Personal computer local networks report

CERN Document Server

1991-01-01

Please note this is a Short Discount publication. Since the first microcomputer local networks of the late 1970's and early 80's, personal computer LANs have expanded in popularity, especially since the introduction of IBMs first PC in 1981. The late 1980s has seen a maturing in the industry with only a few vendors maintaining a large share of the market. This report is intended to give the reader a thorough understanding of the technology used to build these systems ... from cable to chips ... to ... protocols to servers. The report also fully defines PC LANs and the marketplace, with in-

[Musculoskeletal disorders among university student computer users].

Science.gov (United States)

Lorusso, A; Bruno, S; L'Abbate, N

2009-01-01

Musculoskeletal disorders are a common problem among computer users. Many epidemiological studies have shown that ergonomic factors and aspects of work organization play an important role in the development of these disorders. We carried out a cross-sectional survey to estimate the prevalence of musculoskeletal symptoms among university students using personal computers and to investigate the features of occupational exposure and the prevalence of symptoms throughout the study course. Another objective was to assess the students' level of knowledge of computer ergonomics and the relevant health risks. A questionnaire was distributed to 183 students attending the lectures for second and fourth year courses of the Faculty of Architecture. Data concerning personal characteristics, ergonomic and organizational aspects of computer use, and the presence of musculoskeletal symptoms in the neck and upper limbs were collected. Exposure to risk factors such as daily duration of computer use, time spent at the computer without breaks, duration of mouse use and poor workstation ergonomics was significantly higher among students of the fourth year course. Neck pain was the most commonly reported symptom (69%), followed by hand/wrist (53%), shoulder (49%) and arm (8%) pain. The prevalence of symptoms in the neck and hand/wrist area was signifcantly higher in the students of the fourth year course. In our survey we found high prevalence of musculoskeletal symptoms among university students using computers for long time periods on a daily basis. Exposure to computer-related ergonomic and organizational risk factors, and the prevalence ofmusculoskeletal symptoms both seem to increase significantly throughout the study course. Furthermore, we found that the level of perception of computer-related health risks among the students was low. Our findings suggest the need for preventive intervention consisting of education in computer ergonomics.

Personalized Computer-Assisted Mathematics Problem-Solving Program and Its Impact on Taiwanese Students

Science.gov (United States)

Chen, Chiu-Jung; Liu, Pei-Lin

2007-01-01

This study evaluated the effects of a personalized computer-assisted mathematics problem-solving program on the performance and attitude of Taiwanese fourth grade students. The purpose of this study was to determine whether the personalized computer-assisted program improved student performance and attitude over the nonpersonalized program.…

Computing for magnetic fusion energy research: An updated vision

International Nuclear Information System (INIS)

Henline, P.; Giarrusso, J.; Davis, S.; Casper, T.

1993-01-01

This Fusion Computing Council perspective is written to present the primary of the fusion computing community at the time of publication of the report necessarily as a summary of the information contained in the individual sections. These concerns reflect FCC discussions during final review of contributions from the various working groups and portray our latest information. This report itself should be considered as dynamic, requiring periodic updating in an attempt to track rapid evolution of the computer industry relevant to requirements for magnetic fusion research. The most significant common concern among the Fusion Computing Council working groups is networking capability. All groups see an increasing need for network services due to the use of workstations, distributed computing environments, increased use of graphic services, X-window usage, remote experimental collaborations, remote data access for specific projects and other collaborations. Other areas of concern include support for workstations, enhanced infrastructure to support collaborations, the User Service Centers, NERSC and future massively parallel computers, and FCC sponsored workshops

The use of personal computers for self-teaching

International Nuclear Information System (INIS)

Levrat, B.

1983-01-01

The number of personal computers is growing at a phenomenal rate. Their capabilities in man-machine interaction makes them useful in teaching a variety of subjects. They can offer a stimulating presentation of the material to be learned, varied drill and practice exercices and simulations. Testing, evaluation and progress monitoring are also possible. Key issues about quality and content should not be left to businessmen alone. At CERN, Computer Aided Learning could be useful in connexion with large experiments. (orig.)

Efficacy of a telerehabilitation intervention programme using biofeedback among computer operators.

Science.gov (United States)

Golebowicz, Merav; Levanon, Yafa; Palti, Ram; Ratzon, Navah Z

2015-01-01

Computer operators spend long periods of time sitting in a static posture at computer workstations and therefore have an increased exposure to work-related musculoskeletal disorders (WRMSD). The present study is aimed at investigating the feasibility and effectiveness of a tele-biofeedback ergonomic intervention programme among computer operators suffering from WRMSD. Twelve subjects with WRMSD were assigned an ergonomic intervention accompanied by remote tele-biofeedback training, which was practised at their workstations. Evaluations of pain symptoms and locations, body posture and psychosocial characteristics were carried out before and after the intervention in the workplace. The hypothesis was partially verified as it showed improved body position at the workstation and decreased pain in some body parts. Tele-biofeedback, as part of an intervention, appears to be feasible and efficient for computer operators who suffer from WRMSD. This study encourages further research on tele-health within the scope of occupational therapy practice. Practitioner summary: Research concerning tele-health using biofeedback is scarce. The present study analyses the feasibility and partial effectiveness of a tele-biofeedback ergonomic intervention programme for computer operators suffering from WRMSD. The uniqueness and singularity of this study is the usage of remote communication between participants and practitioners through the Internet.

COMPUTATION FORMAT computer codes X4TOC4 and PLOTC4. Implementing and Testing on a Personal Computer

International Nuclear Information System (INIS)

McLaughlin, P.K.

1987-05-01

This document describes the contents of the diskette containing the COMPUTATION FORMAT codes X4TOC4 and PLOTC4 by D.E. Cullen, and example data for use in implementing and testing these codes on a Personal Computer of the type IBM-PC/AT. Upon request the codes are available from the IAEA Nuclear Data Section, free of charge, on a single diskette. (author)

Human-computer interface incorporating personal and application domains

Science.gov (United States)

Anderson, Thomas G [Albuquerque, NM

2011-03-29

The present invention provides a human-computer interface. The interface includes provision of an application domain, for example corresponding to a three-dimensional application. The user is allowed to navigate and interact with the application domain. The interface also includes a personal domain, offering the user controls and interaction distinct from the application domain. The separation into two domains allows the most suitable interface methods in each: for example, three-dimensional navigation in the application domain, and two- or three-dimensional controls in the personal domain. Transitions between the application domain and the personal domain are under control of the user, and the transition method is substantially independent of the navigation in the application domain. For example, the user can fly through a three-dimensional application domain, and always move to the personal domain by moving a cursor near one extreme of the display.

Use of a personal computer for instrumentation testing at the FFTF

International Nuclear Information System (INIS)

Clark, D.A.

1985-01-01

The FFTF uses computers to assist in performance of instrumentation calibration checks for Technical Specification compliance. When the computers used for these checks are not available, back-up methods must be used. A method of using a personal computer to serve as a back-up is discussed, and the hardware used is described

Experimental data processing techniques by a personal computer

International Nuclear Information System (INIS)

Matsuura, Kiyokata; Tsuda, Kenzo; Abe, Yoshihiko; Kojima, Tsuyoshi; Nishikawa, Akira; Shimura, Hitoshi; Hyodo, Hiromi; Yamagishi, Shigeru.

1989-01-01

A personal computer (16-bit, about 1 MB memory) can be used at a low cost in the experimental data processing. This report surveys the important techniques on A/D and D/A conversion, display, store and transfer of the experimental data. It is also discussed the items to be considered in the software. Practical softwares programed BASIC and Assembler language are given as examples. Here, we present some techniques to get faster process in BASIC language and show that the system composed of BASIC and Assembler is useful in a practical experiment. The system performance such as processing speed and flexibility in setting operation condition will depend strongly on programming language. We have made test for processing speed by some typical programming languages; BASIC(interpreter), C, FORTRAN and Assembler. As for the calculation, FORTRAN has the best performance which is comparable to or better than Assembler even in the personal computer. (author)

Workstation Table Engineering Model Design, Development, Fabrication, and Testing

Science.gov (United States)

2012-05-01

This research effort is focused on providing a workstation table design that will reduce the risk of occupant injuries due to secondary impacts and to compartmentalize the occupants to prevent impacts with other objects and/or passengers seated acros...

Studies on radio-diagnosis workstations

International Nuclear Information System (INIS)

Niguet, A.

2008-01-01

Radio-diagnosis ranges from mammography to interventional radiology, and represents a great majority of medical examinations, and is therefore the main source of exposure for the population. The author gives an overview of methods for workstation assessment, mainly based on the dose-area product. She indicates the factors affecting the radiation quantity, and evokes the influence of the type of examination. Measurements enable workers to be classified, an adapted dosimetry follow-on to be implemented, working areas to be delimited, collective and individual protections to be implemented, and recommendations to be drafted. Results obtained on a cardiologist are presented

Interaction techniques for radiology workstations: impact on users' productivity

Science.gov (United States)

Moise, Adrian; Atkins, M. Stella

2004-04-01

As radiologists progress from reading images presented on film to modern computer systems with images presented on high-resolution displays, many new problems arise. Although the digital medium has many advantages, the radiologist"s job becomes cluttered with many new tasks related to image manipulation. This paper presents our solution for supporting radiologists" interpretation of digital images by automating image presentation during sequential interpretation steps. Our method supports scenario based interpretation, which group data temporally, according to the mental paradigm of the physician. We extended current hanging protocols with support for "stages". A stage reflects the presentation of digital information required to complete a single step within a complex task. We demonstrated the benefits of staging in a user study with 20 lay subjects involved in a visual conjunctive search for targets, similar to a radiology task of identifying anatomical abnormalities. We designed a task and a set of stimuli which allowed us to simulate the interpretation workflow from a typical radiology scenario - reading a chest computed radiography exam when a prior study is also available. The simulation was possible by abstracting the radiologist"s task and the basic workstation navigation functionality. We introduced "Stages," an interaction technique attuned to the radiologist"s interpretation task. Compared to the traditional user interface, Stages generated a 14% reduction in the average interpretation.

Cluster computing for lattice QCD simulations

International Nuclear Information System (INIS)

Coddington, P.D.; Williams, A.G.

2000-01-01

Full text: Simulations of lattice quantum chromodynamics (QCD) require enormous amounts of compute power. In the past, this has usually involved sharing time on large, expensive machines at supercomputing centres. Over the past few years, clusters of networked computers have become very popular as a low-cost alternative to traditional supercomputers. The dramatic improvements in performance (and more importantly, the ratio of price/performance) of commodity PCs, workstations, and networks have made clusters of off-the-shelf computers an attractive option for low-cost, high-performance computing. A major advantage of clusters is that since they can have any number of processors, they can be purchased using any sized budget, allowing research groups to install a cluster for their own dedicated use, and to scale up to more processors if additional funds become available. Clusters are now being built for high-energy physics simulations. Wuppertal has recently installed ALiCE, a cluster of 128 Alpha workstations running Linux, with a peak performance of 158 G flops. The Jefferson Laboratory in the US has a 16 node Alpha cluster and plans to upgrade to a 256 processor machine. In Australia, several large clusters have recently been installed. Swinburne University of Technology has a cluster of 64 Compaq Alpha workstations used for astrophysics simulations. Early this year our DHPC group constructed a cluster of 116 dual Pentium PCs (i.e. 232 processors) connected by a Fast Ethernet network, which is used by chemists at Adelaide University and Flinders University to run computational chemistry codes. The Australian National University has recently installed a similar PC cluster with 192 processors. The Centre for the Subatomic Structure of Matter (CSSM) undertakes large-scale high-energy physics calculations, mainly lattice QCD simulations. The choice of the computer and network hardware for a cluster depends on the particular applications to be run on the machine. Our

The driver workstation in commercial vehicles; Ergonomie und Design von Fahrerarbeitsplaetzen in Nutzfahrzeugen

Energy Technology Data Exchange (ETDEWEB)

Kraus, W. [HAW-Hamburg (Germany)

2003-07-01

Nowadays, ergonomics and design are quality factors and indispensable elements of commercial vehicle design and development. Whereas a vehicle's appearance, i.e. its outside design, produces fascination and image, the design of its passenger cell focuses entirely on drivers and their tasks. Today, passenger-cell design and the ergonomics of driver workstations in commercial vehicles are clearly becoming more and more important. This article concentrates above all on defining commercial vehicle drivers, which, within the scope of research projects on coach-driver workstations, has provided new insight into the design of driver workstations. In light of the deficits determined, the research project mainly focused on designing driver workstations which were in line with the latest findings in ergonomics and human engineering. References to the methodology of driver-workstation optimization seems important in this context. The afore-mentioned innovations in the passenger cells of commercial vehicles will be explained and described by means of topical and practical examples. (orig.) [German] Ergonomie und Design sind heute Qualitaetsfaktoren und unverzichtbarer Bestandteil bei der Entwicklung von Nutzfahrzeugen. Erzeugt das Erscheinungsbild, die Aussengestaltung des Fahrzeugs, die Faszination und das Image, so ist die Innengestaltung weitgehend ganz auf die Bedienpersonen und ihre Arbeitsaufgaben bezogen. Die Innenraumgestaltung und die Ergonomie von Fahrerarbeitsplaetzen in Nutzfahrzeugen sind heute in einer Phase der deutlichen Aufwertung zu sehen. Im Beitrag wird besonders auf die Definition der Bedienpersonen fuer Nutzfahrzeuge eingegangen, die im Rahmen des Forschungsprojekts Fahrerarbeitsplatz im Reisebus zu neuen Erkenntnissen bei der Auslegung von Arbeitsplaetzen fuehrte. Gemaess der ermittelten Defizite konzentriert sich die Studie im Kern auf das Gestaltungskonzept des Fahrerarbeitsplatzes nach ergonomischen und arbeitswissenschaftlichen Erkenntnissen

Making the PACS workstation a browser of image processing software: a feasibility study using inter-process communication techniques.

Science.gov (United States)

Wang, Chunliang; Ritter, Felix; Smedby, Orjan

2010-07-01

To enhance the functional expandability of a picture archiving and communication systems (PACS) workstation and to facilitate the integration of third-part image-processing modules, we propose a browser-server style method. In the proposed solution, the PACS workstation shows the front-end user interface defined in an XML file while the image processing software is running in the background as a server. Inter-process communication (IPC) techniques allow an efficient exchange of image data, parameters, and user input between the PACS workstation and stand-alone image-processing software. Using a predefined communication protocol, the PACS workstation developer or image processing software developer does not need detailed information about the other system, but will still be able to achieve seamless integration between the two systems and the IPC procedure is totally transparent to the final user. A browser-server style solution was built between OsiriX (PACS workstation software) and MeVisLab (Image-Processing Software). Ten example image-processing modules were easily added to OsiriX by converting existing MeVisLab image processing networks. Image data transfer using shared memory added communication based on IPC techniques is an appealing method that allows PACS workstation developers and image processing software developers to cooperate while focusing on different interests.

Development of a new discharge control system utilizing UNIX workstations and VME-bus systems for JT-60

Energy Technology Data Exchange (ETDEWEB)

Akasaka, Hiromi; Sueoka, Michiharu; Takano, Shoji; Totsuka, Toshiyuki; Yonekawa, Izuru; Kurihara, Kenichi; Kimura, Toyoaki [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

2002-01-01

The JT-60 discharge control system, which had used HIDIC-80E 16 bit mini-computers and CAMAC systems since the start of JT-60 experiment in 1985, was renewed in March, 2001. The new system consists of a UNIX workstation and a VME-bus system, and features a distributed control system. The workstation performs message communication with a VME-bus system and controllers of JT-60 sub-systems and processing for discharge control because of its flexibility to construction of a new network and modifications of software. The VME-bus system performs discharge sequence control because it is suitable for fast real time control and flexible to the hardware extension. The replacement has improved the control function and reliability of the discharge control system and also has provided sufficient performance necessary for future modifications of JT-60. The new system has been running successfully since April 2001. The data acquisition speed was confirmed to be twice faster than the previous one. This report describes major functions of the discharge control system, technical ideas for developing the system and results of the initial operation in detail. (author)

High-performance computing — an overview

Science.gov (United States)

Marksteiner, Peter

1996-08-01

An overview of high-performance computing (HPC) is given. Different types of computer architectures used in HPC are discussed: vector supercomputers, high-performance RISC processors, various parallel computers like symmetric multiprocessors, workstation clusters, massively parallel processors. Software tools and programming techniques used in HPC are reviewed: vectorizing compilers, optimization and vector tuning, optimization for RISC processors; parallel programming techniques like shared-memory parallelism, message passing and data parallelism; and numerical libraries.

Instrument workstation for the EGSE of the Near Infrared Spectro-Photometer instrument (NISP) of the EUCLID mission

Science.gov (United States)

Trifoglio, M.; Gianotti, F.; Conforti, V.; Franceschi, E.; Stephen, J. B.; Bulgarelli, A.; Fioretti, V.; Maiorano, E.; Nicastro, L.; Valenziano, L.; Zoli, A.; Auricchio, N.; Balestra, A.; Bonino, D.; Bonoli, C.; Bortoletto, F.; Capobianco, V.; Chiarusi, T.; Corcione, L.; Debei, S.; De Rosa, A.; Dusini, S.; Fornari, F.; Giacomini, F.; Guizzo, G. P.; Ligori, S.; Margiotta, A.; Mauri, N.; Medinaceli, E.; Morgante, G.; Patrizii, L.; Sirignano, C.; Sirri, G.; Sortino, F.; Stanco, L.; Tenti, M.

2016-07-01

The NISP instrument on board the Euclid ESA mission will be developed and tested at different levels of integration using various test equipment which shall be designed and procured through a collaborative and coordinated effort. The NISP Instrument Workstation (NI-IWS) will be part of the EGSE configuration that will support the NISP AIV/AIT activities from the NISP Warm Electronics level up to the launch of Euclid. One workstation is required for the NISP EQM/AVM, and a second one for the NISP FM. Each workstation will follow the respective NISP model after delivery to ESA for Payload and Satellite AIV/AIT and launch. At these levels the NI-IWS shall be configured as part of the Payload EGSE, the System EGSE, and the Launch EGSE, respectively. After launch, the NI-IWS will be also re-used in the Euclid Ground Segment in order to support the Commissioning and Performance Verification (CPV) phase, and for troubleshooting purposes during the operational phase. The NI-IWS is mainly aimed at the local storage in a suitable format of the NISP instrument data and metadata, at local retrieval, processing and display of the stored data for on-line instrument assessment, and at the remote retrieval of the stored data for off-line analysis on other computers. We describe the design of the IWS software that will create a suitable interface to the external systems in each of the various configurations envisaged at the different levels, and provide the capabilities required to monitor and verify the instrument functionalities and performance throughout all phases of the NISP lifetime.

Cloud Computing Application of Personal Information's Security in Network Sales-channels

OpenAIRE

Sun Qiong; Min Liu; Shiming Pang

2013-01-01

With the promotion of Internet sales, the security of personal information to network users have become increasingly demanding. The existing network of sales channels has personal information security risks, vulnerable to hacker attacking. Taking full advantage of cloud security management strategy, cloud computing security management model is introduced to the network sale of personal information security applications, which is to solve the problem of information leakage. Then we proposed me...

Mobile clusters of single board computers: an option for providing resources to student projects and researchers.

Science.gov (United States)

Baun, Christian

2016-01-01

Clusters usually consist of servers, workstations or personal computers as nodes. But especially for academic purposes like student projects or scientific projects, the cost for purchase and operation can be a challenge. Single board computers cannot compete with the performance or energy-efficiency of higher-value systems, but they are an option to build inexpensive cluster systems. Because of the compact design and modest energy consumption, it is possible to build clusters of single board computers in a way that they are mobile and can be easily transported by the users. This paper describes the construction of such a cluster, useful applications and the performance of the single nodes. Furthermore, the clusters' performance and energy-efficiency is analyzed by executing the High Performance Linpack benchmark with a different number of nodes and different proportion of the systems total main memory utilized.

Personality Trait and Facial Expression Filter-Based Brain-Computer Interface

Directory of Open Access Journals (Sweden)

Seongah Chin

2013-02-01

Full Text Available In this paper, we present technical approaches that bridge the gap in the research related to the use of brain-computer interfaces for entertainment and facial expressions. Such facial expressions that reflect an individual's personal traits can be used to better realize artificial facial expressions in a gaming environment based on a brain-computer interface. First, an emotion extraction filter is introduced in order to classify emotions on the basis of the users' brain signals in real time. Next, a personality trait filter is defined to classify extrovert and introvert types, which manifest as five traits: very extrovert, extrovert, medium, introvert and very introvert. In addition, facial expressions derived from expression rates are obtained by an extrovert-introvert fuzzy model through its defuzzification process. Finally, we confirm this validation via an analysis of the variance of the personality trait filter, a k-fold cross validation of the emotion extraction filter, an accuracy analysis, a user study of facial synthesis and a test case game.

A software to report and file by personal computer

International Nuclear Information System (INIS)

Di Giandomenico, E.; Filippone, A.; Esposito, A.; Bonomo, L.

1989-01-01

During the past four years the authors have been gaining experince in reporting radiological examinations by personal computer. Today they describe the project of a new software which allows the reporting and filing of roentgenograms. This program was realized by a radiologist, using a well known data base management system: dBASE III. The program was shaped to fit the radiologist's needs: it helps to report, and allows to file, radiological data, with the diagnosic codes used by the American College of Radiology. In this paper the authors describe the data base structure and indicate the software functions which make its use possible. Thus, this paper is not aimed at advertising a new reporting program, but at demonstrating how the radiologist can himself manage some aspects of his work with the help of a personal computer

Establishing a communications link between two different, incompatible, personal computers: with practical examples and illustrations and program code.

Science.gov (United States)

Davidson, R W

1985-01-01

The increasing need to communicate to exchange data can be handled by personal microcomputers. The necessity for the transference of information stored in one type of personal computer to another type of personal computer is often encountered in the process of integrating multiple sources of information stored in different and incompatible computers in Medical Research and Practice. A practical example is demonstrated with two relatively inexpensive commonly used computers, the IBM PC jr. and the Apple IIe. The basic input/output (I/O) interface chip for serial communication for each computer are joined together using a Null connector and cable to form a communications link. Using BASIC (Beginner's All-purpose Symbolic Instruction Code) Computer Language and the Disk Operating System (DOS) the communications handshaking protocol and file transfer is established between the two computers. The BASIC programming languages used are Applesoft (Apple Personal Computer) and PC BASIC (IBM Personal computer).

The Atmospheric Release Advisory Capability Site Workstation System

International Nuclear Information System (INIS)

Foster, K.T.; Sumikawa, D.A.; Foster, C.S.; Baskett, R.L.

1993-01-01

The Atmospheric Release Advisory Capability (ARAC) is a centralized emergency response service that assesses the consequences that may result from an atmospheric release of toxic material. ARAC was developed by the Lawrence Livermore National Laboratory (LLNL) for the Departments of Energy (DOE) and Defense (DOD) and responds principally to radiological accidents. ARAC provides radiological health and safety guidance to decision makers in the form of computer-generated estimates of the effects of an actual, or potential release of radioactive material into the atmosphere. Upon receipt of the release scenario, the ARAC assessment staff extracts meteorological, topographic, and geographic data from resident world-wide databases for use in complex, three-dimensional transport and diffusion models. These dispersion models generate air concentration (or dose) and ground deposition contour plots showing estimates of the contamination patterns produced as the toxic material is carried by the prevailing winds. To facilitate the ARAC response to a release from specific DOE and DOD sites and to provide these sites with a local emergency response tool, a remote Site Workstation System (SWS) is being placed at various ARAC-supported facilities across the country.. This SWS replaces the existing antiquated ARAC Site System now installed at many of these sites. The new system gives users access to complex atmospheric dispersion models that may be run either by the ARAC staff at LLNL, or (in a later phase of the system) by site personnel using the computational resources of the SWS. Supporting this primary function are a variety of SWS-resident supplemental capabilities that include meteorological data acquisition, manipulation of release-specific databases, computer-based communications, and the use of a simpler Gaussian trajectory puff model that is based on Environmental Protection Agency's INPUFF code

Office ergonomics training and a sit-stand workstation: effects on musculoskeletal and visual symptoms and performance of office workers.

Science.gov (United States)

Robertson, Michelle M; Ciriello, Vincent M; Garabet, Angela M

2013-01-01

Work Related Musculoskeletal Disorders (WMSDs) among office workers with intensive computer use is widespread and the prevalence of symptoms is growing. This randomized controlled trial investigated the effects of an office ergonomics training combined with a sit-stand workstation on musculoskeletal and visual discomfort, behaviors and performance. Participants performed a lab-based customer service job for 8 h per day, over 15 days and were assigned to: Ergonomics Trained (n = 11) or Minimally Trained (n = 11). The training consisted of: a 1.5-h interactive instruction, a sit/stand practice period, and ergonomic reminders. Ergonomics Trained participants experienced minimal musculoskeletal and visual discomfort across the 15 days, varied their postures, with significantly higher performance compared to the Minimally Trained group who had a significantly higher number of symptoms, suggesting that training plays a critical role. The ability to mitigate symptoms, change behaviors and enhance performance through training combined with a sit-stand workstation has implications for preventing discomforts in office workers. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Scientific visualization in computational aerodynamics at NASA Ames Research Center

Science.gov (United States)

Bancroft, Gordon V.; Plessel, Todd; Merritt, Fergus; Walatka, Pamela P.; Watson, Val

1989-01-01

The visualization methods used in computational fluid dynamics research at the NASA-Ames Numerical Aerodynamic Simulation facility are examined, including postprocessing, tracking, and steering methods. The visualization requirements of the facility's three-dimensional graphical workstation are outlined and the types hardware and software used to meet these requirements are discussed. The main features of the facility's current and next-generation workstations are listed. Emphasis is given to postprocessing techniques, such as dynamic interactive viewing on the workstation and recording and playback on videodisk, tape, and 16-mm film. Postprocessing software packages are described, including a three-dimensional plotter, a surface modeler, a graphical animation system, a flow analysis software toolkit, and a real-time interactive particle-tracer.

Computer assisted radiology and surgery. CARS 2010

International Nuclear Information System (INIS)

Anon.

2010-01-01

The conference proceedings include contributions to the following topics: (1) CARS Clinical Day: minimally invasive spiral surgery, interventional radiology; (2) CARS - computer assisted radiology and surgery: ophthalmology, stimulation methods, new approaches to diagnosis and therapy; (3) Computer assisted radiology 24th International congress and exhibition: computer tomography and magnetic resonance, digital angiographic imaging, digital radiography, ultrasound, computer assisted radiation therapy, medical workstations, image processing and display; (4) 14th Annual conference of the International Society for computer aided surgery; ENT-CMF head and neck surgery computer-assisted neurosurgery, cardiovascular surgery, image guided liver surgery, abdominal and laparoscopic surgery, computer-assisted orthopedic surgery, image processing and visualization, surgical robotics and instrumentation, surgical modeling, simulation and education; (5) 28th International EuroPACS meeting: image distribution and integration strategies, planning and evaluation, telemedicine and standards, workflow and data flow in radiology; (6) 11th CARS/SPIE/EuroPACS joint workshop on surgical PACS and the digital operating, management and assessment of OR systems and integration; (7) 12th International workshop on computer-aided diagnosis: special session on breast CAD, special session on thoracic CAD, special session on abdominal brain, lumbar spine CAD; (8) 16th computed Maxillofacial imaging congress: computed maxillofacial imaging in dental implantology, orthodontics and dentofacial orthopedics; approaches to 3D maxillofacial imaging; surgical navigation; (9) 2nd EuroNOTES/CARS workshop on NOTES: an interdisciplinary challenge; (10) 2nd EPMA/CARS workshop on personalized medicine and ICT.; (11)poster sessions.

Computer assisted radiology and surgery. CARS 2010

Energy Technology Data Exchange (ETDEWEB)

Anon.

2010-06-15

The conference proceedings include contributions to the following topics: (1) CARS Clinical Day: minimally invasive spiral surgery, interventional radiology; (2) CARS - computer assisted radiology and surgery: ophthalmology, stimulation methods, new approaches to diagnosis and therapy; (3) Computer assisted radiology 24th International congress and exhibition: computer tomography and magnetic resonance, digital angiographic imaging, digital radiography, ultrasound, computer assisted radiation therapy, medical workstations, image processing and display; (4) 14th Annual conference of the International Society for computer aided surgery; ENT-CMF head and neck surgery computer-assisted neurosurgery, cardiovascular surgery, image guided liver surgery, abdominal and laparoscopic surgery, computer-assisted orthopedic surgery, image processing and visualization, surgical robotics and instrumentation, surgical modeling, simulation and education; (5) 28th International EuroPACS meeting: image distribution and integration strategies, planning and evaluation, telemedicine and standards, workflow and data flow in radiology; (6) 11th CARS/SPIE/EuroPACS joint workshop on surgical PACS and the digital operating, management and assessment of OR systems and integration; (7) 12th International workshop on computer-aided diagnosis: special session on breast CAD, special session on thoracic CAD, special session on abdominal brain, lumbar spine CAD; (8) 16th computed Maxillofacial imaging congress: computed maxillofacial imaging in dental implantology, orthodontics and dentofacial orthopedics; approaches to 3D maxillofacial imaging; surgical navigation; (9) 2nd EuroNOTES/CARS workshop on NOTES: an interdisciplinary challenge; (10) 2nd EPMA/CARS workshop on personalized medicine and ICT.; (11)poster sessions.

Assessment of toxic metals in waste personal computers

International Nuclear Information System (INIS)

Kolias, Konstantinos; Hahladakis, John N.; Gidarakos, Evangelos

2014-01-01

Highlights: • Waste personal computers were collected and dismantled in their main parts. • Motherboards, monitors and plastic housing were examined in their metal content. • Concentrations measured were compared to the RoHS Directive, 2002/95/EC. • Pb in motherboards and funnel glass of devices released <2006 was above the limit. • Waste personal computers need to be recycled and environmentally sound managed. - Abstract: Considering the enormous production of waste personal computers nowadays, it is obvious that the study of their composition is necessary in order to regulate their management and prevent any environmental contamination caused by their inappropriate disposal. This study aimed at determining the toxic metals content of motherboards (printed circuit boards), monitor glass and monitor plastic housing of two Cathode Ray Tube (CRT) monitors, three Liquid Crystal Display (LCD) monitors, one LCD touch screen monitor and six motherboards, all of which were discarded. In addition, concentrations of chromium (Cr), cadmium (Cd), lead (Pb) and mercury (Hg) were compared with the respective limits set by the RoHS 2002/95/EC Directive, that was recently renewed by the 2012/19/EU recast, in order to verify manufacturers’ compliance with the regulation. The research included disassembly, pulverization, digestion and chemical analyses of all the aforementioned devices. The toxic metals content of all samples was determined using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The results demonstrated that concentrations of Pb in motherboards and funnel glass of devices with release dates before 2006, that is when the RoHS Directive came into force, exceeded the permissible limit. In general, except from Pb, higher metal concentrations were detected in motherboards in comparison with plastic housing and glass samples. Finally, the results of this work were encouraging, since concentrations of metals referred in the RoHS Directive were found in

Assessment of toxic metals in waste personal computers

Energy Technology Data Exchange (ETDEWEB)

Kolias, Konstantinos; Hahladakis, John N., E-mail: john_chach@yahoo.gr; Gidarakos, Evangelos, E-mail: gidarako@mred.tuc.gr

2014-08-15

Highlights: • Waste personal computers were collected and dismantled in their main parts. • Motherboards, monitors and plastic housing were examined in their metal content. • Concentrations measured were compared to the RoHS Directive, 2002/95/EC. • Pb in motherboards and funnel glass of devices released <2006 was above the limit. • Waste personal computers need to be recycled and environmentally sound managed. - Abstract: Considering the enormous production of waste personal computers nowadays, it is obvious that the study of their composition is necessary in order to regulate their management and prevent any environmental contamination caused by their inappropriate disposal. This study aimed at determining the toxic metals content of motherboards (printed circuit boards), monitor glass and monitor plastic housing of two Cathode Ray Tube (CRT) monitors, three Liquid Crystal Display (LCD) monitors, one LCD touch screen monitor and six motherboards, all of which were discarded. In addition, concentrations of chromium (Cr), cadmium (Cd), lead (Pb) and mercury (Hg) were compared with the respective limits set by the RoHS 2002/95/EC Directive, that was recently renewed by the 2012/19/EU recast, in order to verify manufacturers’ compliance with the regulation. The research included disassembly, pulverization, digestion and chemical analyses of all the aforementioned devices. The toxic metals content of all samples was determined using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). The results demonstrated that concentrations of Pb in motherboards and funnel glass of devices with release dates before 2006, that is when the RoHS Directive came into force, exceeded the permissible limit. In general, except from Pb, higher metal concentrations were detected in motherboards in comparison with plastic housing and glass samples. Finally, the results of this work were encouraging, since concentrations of metals referred in the RoHS Directive were found in

Utilization of a multimedia PACS workstation for surgical planning of epilepsy

Science.gov (United States)

Soo Hoo, Kent; Wong, Stephen T.; Hawkins, Randall A.; Knowlton, Robert C.; Laxer, Kenneth D.; Rowley, Howard A.

1997-05-01

Surgical treatment of temporal lobe epilepsy requires the localization of the epileptogenic zone for surgical resection. Currently, clinicians utilize electroencephalography, various neuroimaging modalities, and psychological tests together to determine the location of this zone. We investigate how a multimedia neuroimaging workstation built on top of the UCSF Picture Archiving and Communication System can be used to aid surgical planning of epilepsy and related brain diseases. This usage demonstrates the ability of the workstation to retrieve image and textural data from PACS and other image sources, register multimodality images, visualize and render 3D data sets, analyze images, generate new image and text data from the analysis, and organize all data in a relational database management system.

Use of personal computer image for processing a magnetic resonance image (MRI)

International Nuclear Information System (INIS)

Yamamoto, Tetsuo; Tanaka, Hitoshi

1988-01-01

Image processing of MR imaging was attempted by using a popular personal computer as 16-bit model. The computer processed the images on a 256 x 256 matrix and 512 x 512 matrix. The softwer languages for image-processing were those of Macro-Assembler performed by (MS-DOS). The original images, acuired with an 0.5 T superconducting machine (VISTA MR 0.5 T, Picker International) were transfered to the computer by the flexible disket. Image process are the display of image to monitor, other the contrast enhancement, the unsharped mask contrast enhancement, the various filter process, the edge detections or the color histogram was obtained in 1.6 sec to 67 sec, indicating that commercialzed personal computer had ability for routine clinical purpose in MRI-processing. (author)

A vector-product information retrieval system adapted to heterogeneous, distributed computing environments

Science.gov (United States)

Rorvig, Mark E.

1991-01-01

Vector-product information retrieval (IR) systems produce retrieval results superior to all other searching methods but presently have no commercial implementations beyond the personal computer environment. The NASA Electronic Library Systems (NELS) provides a ranked list of the most likely relevant objects in collections in response to a natural language query. Additionally, the system is constructed using standards and tools (Unix, X-Windows, Notif, and TCP/IP) that permit its operation in organizations that possess many different hosts, workstations, and platforms. There are no known commercial equivalents to this product at this time. The product has applications in all corporate management environments, particularly those that are information intensive, such as finance, manufacturing, biotechnology, and research and development.

Improving personality facet scores with multidimensional computer adaptive testing

DEFF Research Database (Denmark)

Makransky, Guido; Mortensen, Erik Lykke; Glas, Cees A W

2013-01-01

personality tests contain many highly correlated facets. This article investigates the possibility of increasing the precision of the NEO PI-R facet scores by scoring items with multidimensional item response theory and by efficiently administering and scoring items with multidimensional computer adaptive...

An approach to develop a PSA workstation in KAERI

International Nuclear Information System (INIS)

Kim, T. W.; Han, S. H.; Park, C. K.

1995-01-01

This paper describes three kinds of efforts for the development of PSA workstation in KAERI; Development of a PSA tool, KIRAP, Reliability Database Development, Living PSA tool development. Korea has 9 nuclear power plants (NPPs) in operation and 9 NPPs under design or construction. For the NPPs recently constructed or designed, the probabilistic safety assessments (PSAs) have been performed by the Government requirements. For these PSAs, the MSDOS version of KIRAP has been used. For the consistent data management and the easiness of information handling needed in PSA, APSA workstation, KIRAP-Win is under development under Windows environment. For the reliability database on component failure rate, human error rate, and common cause failure rate, data used in international PSA or reliability data handbook are collected and processed to use in Korean new plants' PSAs. Finally, an effort for the development of a living PSA tool in KAERI based on dynamic PSA concept is described

Ergonomics in the computer workstation | Karoney | East African ...

African Journals Online (AJOL)

If you would like more information about how to print, save, and work with PDFs, Highwire Press provides a helpful Frequently Asked Questions about PDFs. Alternatively, you can download the PDF file directly to your computer, from where it can be opened using a PDF reader. To download the PDF, click the Download link ...

From parallel to distributed computing for reactive scattering calculations

International Nuclear Information System (INIS)

Lagana, A.; Gervasi, O.; Baraglia, R.

1994-01-01

Some reactive scattering codes have been ported on different innovative computer architectures ranging from massively parallel machines to clustered workstations. The porting has required a drastic restructuring of the codes to single out computationally decoupled cpu intensive subsections. The suitability of different theoretical approaches for parallel and distributed computing restructuring is discussed and the efficiency of related algorithms evaluated

Thinking computers and virtual persons essays on the intentionality of machines

CERN Document Server

Dietrich, Eric

1994-01-01

Thinking Computers and Virtual Persons: Essays on the Intentionality of Machines explains how computations are meaningful and how computers can be cognitive agents like humans. This book focuses on the concept that cognition is computation.Organized into four parts encompassing 13 chapters, this book begins with an overview of the analogy between intentionality and phlogiston, the 17th-century principle of burning. This text then examines the objection to computationalism that it cannot prevent arbitrary attributions of content to the various data structures and representations involved in a c

Easy-to-use application programs for decay heat and delayed neutron calculations on personal computers

Energy Technology Data Exchange (ETDEWEB)

Oyamatsu, Kazuhiro [Nagoya Univ. (Japan)

1998-03-01

Application programs for personal computers are developed to calculate the decay heat power and delayed neutron activity from fission products. The main programs can be used in any computers from personal computers to main frames because their sources are written in Fortran. These programs have user friendly interfaces to be used easily not only for research activities but also for educational purposes. (author)

[Influence of different lighting levels at workstations with video display terminals on operators' work efficiency].

Science.gov (United States)

Janosik, Elzbieta; Grzesik, Jan

2003-01-01

The aim of this work was to evaluate the influence of different lighting levels at workstations with video display terminals (VDTs) on the course of the operators' visual work, and to determine the optimal levels of lighting at VDT workstations. For two kinds of job (entry of figures from a typescript and edition of the text displayed on the screen), the work capacity, the degree of the visual strain and the operators' subjective symptoms were determined for four lighting levels (200, 300, 500 and 750 lx). It was found that the work at VDT workstations may overload the visual system and cause eyes complaints as well as the reduction of accommodation or convergence strength. It was also noted that the edition of the text displayed on the screen is more burdening for operators than the entry of figures from a typescript. Moreover, the examination results showed that the lighting at VDT workstations should be higher than 200 lx and that 300 lx makes the work conditions most comfortable during the entry of figures from a typescript, and 500 lx during the edition of the text displayed on the screen.

Performance of the coupled thermalhydraulics/neutron kinetics code R/P/C on workstation clusters and multiprocessor systems

International Nuclear Information System (INIS)

Hammer, C.; Paffrath, M.; Boeer, R.; Finnemann, H.; Jackson, C.J.

1996-01-01

The light water reactor core simulation code PANBOX has been coupled with the transient analysis code RELAP5 for the purpose of performing plant safety analyses with a three-dimensional (3-D) neutron kinetics model. The system has been parallelized to improve the computational efficiency. The paper describes the features of this system with emphasis on performance aspects. Performance results are given for different types of parallelization, i. e. for using an automatic parallelizing compiler, using the portable PVM platform on a workstation cluster, using PVM on a shared memory multiprocessor, and for using machine dependent interfaces. (author)

SALP-PC, a computer program for fault tree analysis on personal computers

International Nuclear Information System (INIS)

Contini, S.; Poucet, A.

1987-01-01

The paper presents the main characteristics of the SALP-PC computer code for fault tree analysis. The program has been developed in Fortran 77 on an Olivetti M24 personal computer (IBM compatible) in order to reach a high degree of portability. It is composed of six processors implementing the different phases of the analysis procedure. This particular structure presents some advantages like, for instance, the restart facility and the possibility to develop an event tree analysis code. The set of allowed logical operators, i.e. AND, OR, NOT, K/N, XOR, INH, together with the possibility to define boundary conditions, make the SALP-PC code a powerful tool for risk assessment. (orig.)

Know Your Personal Computer Basic Input-Output System (BIOS)

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 7. Know Your Personal Computer Basic Input-Output System (BIOS). Siddhartha Kumar Ghoshal. Series Article Volume 2 Issue 7 July 1997 pp 48-54. Fulltext. Click here to view fulltext PDF. Permanent link:

Effect of Active Workstation on Energy Expenditure and Job Performance: A Systematic Review and Meta-analysis.

Science.gov (United States)

Cao, Chunmei; Liu, Yu; Zhu, Weimo; Ma, Jiangjun

2016-05-01

Recently developed active workstation could become a potential means for worksite physical activity and wellness promotion. The aim of this review was to quantitatively examine the effectiveness of active workstation in energy expenditure and job performance. The literature search was conducted in 6 databases (PubMed, SPORTDiscuss, Web of Science, ProQuest, ScienceDirect, and Scopuse) for articles published up to February 2014, from which a systematic review and meta-analysis was conducted. The cumulative analysis for EE showed there was significant increase in EE using active workstation [mean effect size (MES): 1.47; 95% confidence interval (CI): 1.22 to 1.72, P job performance indicated 2 findings: (1) active workstation did not affect selective attention, processing speed, speech quality, reading comprehension, interpretation and accuracy of transcription; and (2) it could decrease the efficiency of typing speed (MES: -0.55; CI: -0.88 to -0.21, P job performance were significantly lower, others were not. As a result there was little effect on real-life work productivity if we made a good arrangement of job tasks.

The graphics future in scientific applications-trends and developments in computer graphics

CERN Document Server

Enderle, G

1982-01-01

Computer graphics methods and tools are being used to a great extent in scientific research. The future development in this area will be influenced both by new hardware developments and by software advances. On the hardware sector, the development of the raster technology will lead to the increased use of colour workstations with more local processing power. Colour hardcopy devices for creating plots, slides, or movies will be available at a lower price than today. The first real 3D-workstations will appear on the marketplace. One of the main activities on the software sector is the standardization of computer graphics systems, graphical files, and device interfaces. This will lead to more portable graphical application programs and to a common base for computer graphics education.

Micromagnetics on high-performance workstation and mobile computational platforms

Science.gov (United States)

Fu, S.; Chang, R.; Couture, S.; Menarini, M.; Escobar, M. A.; Kuteifan, M.; Lubarda, M.; Gabay, D.; Lomakin, V.

2015-05-01

The feasibility of using high-performance desktop and embedded mobile computational platforms is presented, including multi-core Intel central processing unit, Nvidia desktop graphics processing units, and Nvidia Jetson TK1 Platform. FastMag finite element method-based micromagnetic simulator is used as a testbed, showing high efficiency on all the platforms. Optimization aspects of improving the performance of the mobile systems are discussed. The high performance, low cost, low power consumption, and rapid performance increase of the embedded mobile systems make them a promising candidate for micromagnetic simulations. Such architectures can be used as standalone systems or can be built as low-power computing clusters.

General specifications for the development of a USL/DBMS NASA/PC R and D distributed workstation

Science.gov (United States)

Dominick, Wayne D. (Editor); Chum, Frank Y.

1984-01-01

The general specifications for the development of a PC-based distributed workstation (PCDWS) for an information storage and retrieval systems environment are defined. This research proposes the development of a PCDWS prototype as part of the University of Southwestern Louisiana Data Base Management System (USL/DBMS) NASA/PC R and D project in the PC-based workstation environment.

Regional Platform on Personal Computer Electronic Waste in Latin ...

International Development Research Centre (IDRC) Digital Library (Canada)

Regional Platform on Personal Computer Electronic Waste in Latin America and the Caribbean. Donation of ... This project aims to identify environmentally responsible and sustainable solutions to the problem of e-waste. ... Policy in Focus publishes a special issue profiling evidence to empower women in the labour market.

The potential of computer software that supports the diagnosis of workplace ergonomics in shaping health awareness

Science.gov (United States)

Lubkowska, Wioletta

2017-11-01

The growing prevalence of health problems among computer workstation workers has become one of the biggest threats to the overall health of our population. That is why many modern scientists are looking for ways and methods to prevent and reverse these negative trends. The purpose of this article is to present the potential for practical use of computer programs to design an ergonomic workplace and postural loads. These programs help configure the computer workstation correctly and adopt the correct body position during work, which reduces the risk of health problems. Creating visually attractive programs helps encourage and inspire those who work with a computer to introduce ergonomic solutions and reject the sedentary lifestyle.

Inhaled air quality with desk incorporated personalized ventilation (PV): parametric study

DEFF Research Database (Denmark)

Bolashikov, Zhecho Dimitrov; Nagano, Hideaki; Melikov, Arsen Krikor

A workstation consisting of a desk with installed personalized ventilation (PV) and a dressed breathing thermal manikin simulating seated occupant was set in a full-scale test room. The room was conditioned by overhead ventilation at 26 oC. The PV consisted of two confluent jets incorporated along...

Improved Performance of Personalized Ventilation by Control of the Convection Flow around Occupant Body

DEFF Research Database (Denmark)

Bolashikov, Zhecho Dimitrov; Melikov, Arsen Krikor; Krenek, Miroslav

2009-01-01

This paper reports on methods of control of the free convection flow around human body aiming at improvement of inhaled air quality for occupants at workstations with personalized ventilation (PV). Two methods of control were developed and explored: passive - blocking the free convection developm......This paper reports on methods of control of the free convection flow around human body aiming at improvement of inhaled air quality for occupants at workstations with personalized ventilation (PV). Two methods of control were developed and explored: passive - blocking the free convection......-scale test room with background mixing ventilation. Thermal manikin with realistic free convection flow was used. The PV supplied air from front/above towards the face. All measurements were performed under isothermal conditions at 20 °C and 26 °C. The air in the test room was mixed with tracer gas, while...

Active Workstations Do Not Impair Executive Function in Young and Middle-Age Adults.

Science.gov (United States)

Ehmann, Peter J; Brush, Christopher J; Olson, Ryan L; Bhatt, Shivang N; Banu, Andrea H; Alderman, Brandon L

2017-05-01

This study aimed to examine the effects of self-selected low-intensity walking on an active workstation on executive functions (EF) in young and middle-age adults. Using a within-subjects design, 32 young (20.6 ± 2.0 yr) and 26 middle-age (45.6 ± 11.8 yr) adults performed low-intensity treadmill walking and seated control conditions in randomized order on separate days, while completing an EF test battery. EF was assessed using modified versions of the Stroop (inhibition), Sternberg (working memory), Wisconsin Card Sorting (cognitive flexibility), and Tower of London (global EF) cognitive tasks. Behavioral performance outcomes were assessed using composite task z-scores and traditional measures of reaction time and accuracy. Average HR and step count were also measured throughout. The expected task difficulty effects were found for reaction time and accuracy. No significant main effects or interactions as a function of treadmill walking were found for tasks assessing global EF and the three individual EF domains. Accuracy on the Tower of London task was slightly impaired during slow treadmill walking for both age-groups. Middle-age adults displayed longer planning times for more difficult conditions of the Tower of London during walking compared with sitting. A 50-min session of low-intensity treadmill walking on an active workstation resulted in accruing approximately 4500 steps. These findings suggest that executive function performance remains relatively unaffected while walking on an active workstation, further supporting the use of treadmill workstations as an effective approach to increase physical activity and reduce sedentary time in the workplace.

Online retrieval of patient information by asynchronous communication between general purpose computer and stand-alone personal computer

International Nuclear Information System (INIS)

Tsutsumi, Reiko; Takahashi, Kazuei; Sato, Toshiko; Komatani, Akio; Yamaguchi, Koichi

1988-01-01

Asynchronous communication was made between host (FACOM M-340) and personal computer (OLIBETTIE S-2250) to get patient's information required for RIA test registration. The retrieval system consists of a keyboad input of six numeric codes, patient's ID, and a real time reply containing six parameters for the patient. Their identified parameters are patient's name, sex, date of birth (include area), department, and out- or inpatient. Linking this program to RIA registration program for individual patient, then, operator can input name of RIA test requested. Our simple retrieval program made a useful data network between different types of host and stand-alone personal computers, and enabled us accurate and labor-saving registration for RIA test. (author)

The image database management system of teaching file using personal computer

International Nuclear Information System (INIS)

Shin, M. J.; Kim, G. W.; Chun, T. J.; Ahn, W. H.; Baik, S. K.; Choi, H. Y.; Kim, B. G.

1995-01-01

For the systemic management and easy using of teaching file in radiology department, the authors tried to do the setup of a database management system of teaching file using personal computer. We used a personal computer (IBM PC compatible, 486DX2) including a image capture card(Window vision, Dooin Elect, Seoul, Korea) and video camera recorder (8mm, CCD-TR105, Sony, Tokyo, Japan) for the acquisition and storage of images. We developed the database program by using Foxpro for Window 2.6(Microsoft, Seattle, USA) executed in the Window 3.1 (Microsoft, Seattle, USA). Each datum consisted of hospital number, name, sex, age, examination date, keyword, radiologic examination modalities, final diagnosis, radiologic findings, references and representative images. The images were acquired and stored as bitmap format (8 bitmap, 540 X 390 ∼ 545 X 414, 256 gray scale) and displayed on the 17 inch-flat monitor(1024 X 768, Samtron, Seoul, Korea). Without special devices, the images acquisition and storage could be done on the reading viewbox, simply. The image quality on the computer's monitor was less than the one of original film on the viewbox, but generally the characteristics of each lesions could be differentiated. Easy retrieval of data was possible for the purpose of teaching file system. Without high cost appliances, we could consummate the image database system of teaching file using personal computer with relatively inexpensive method

Experience with workstations for accelerator control at the CERN SPS

International Nuclear Information System (INIS)

Ogle, A.; Ulander, J.; Wilkie, I.

1990-01-01

The CERN super proton synchrotron (SPS) control system is currently undergoing a major long-term upgrade. This paper reviews progress on the high-level application software with particular reference to the operator interface. An important feature of the control-system upgrade is the move from consoles with a number of fixed screens and limited multitasking ability to workstations with the potential to display a large number of windows and perform a number of independent tasks simultaneously. This workstation environment thus permits the operator to run tasks in one machine for which he previously had to monopolize two or even three old consoles. However, the environment also allows the operator to cover the screen with a multitude of windows, leading to complete confusion. Initial requests to present some form of 'global status' of the console proved to be naive, and several iterations were necessary before the operators were satisfied. (orig.)

Presence and biofeedback in first-person perspective computer games

DEFF Research Database (Denmark)

Grimshaw-Aagaard, Mark Nicholas

2019-01-01

. Following the line taken by presence theorists, I differentiate between immersion, an objective measure such that computer game technology can be less or more immersive, and presence, a subjective, human response to that technology. The third section looks at current possibilities for biofeedback...... in relation to sound design for first-person perspective computer games; in line with the first section, biofeedback devices are treated as an immersive technology. I close the chapter by suggesting ways in which sound design in such games might make use of biofeedback to enhance the perception of presence...

Certification of version 1.2 of the PORFLO-3 code for the WHC scientific and engineering computational center

International Nuclear Information System (INIS)

Kline, N.W.

1994-01-01

Version 1.2 of the PORFLO-3 Code has migrated from the Hanford Cray computer to workstations in the WHC Scientific and Engineering Computational Center. The workstation-based configuration and acceptance testing are inherited from the CRAY-based configuration. The purpose of this report is to document differences in the new configuration as compared to the parent Cray configuration, and summarize some of the acceptance test results which have shown that the migrated code is functioning correctly in the new environment

Feedwater heater performance evaluation using the heat exchanger workstation

International Nuclear Information System (INIS)

Ranganathan, K.M.; Singh, G.P.; Tsou, J.L.

1995-01-01

A Heat Exchanger Workstation (HEW) has been developed to monitor the condition of heat exchanging equipment power plants. HEW enables engineers to analyze thermal performance and failure events for power plant feedwater heaters. The software provides tools for heat balance calculation and performance analysis. It also contains an expert system that enables performance enhancement. The Operation and Maintenance (O ampersand M) reference module on CD-ROM for HEW will be available by the end of 1995. Future developments of HEW would result in Condenser Expert System (CONES) and Balance of Plant Expert System (BOPES). HEW consists of five tightly integrated applications: A Database system for heat exchanger data storage, a Diagrammer system for creating plant heat exchanger schematics and data display, a Performance Analyst system for analyzing and predicting heat exchanger performance, a Performance Advisor expert system for expertise on improving heat exchanger performance and a Water Calculator system for computing properties of steam and water. In this paper an analysis of a feedwater heater which has been off-line is used to demonstrate how HEW can analyze the performance of the feedwater heater train and provide an economic justification for either replacing or repairing the feedwater heater

HIGH PERFORMANCE PHOTOGRAMMETRIC PROCESSING ON COMPUTER CLUSTERS

Directory of Open Access Journals (Sweden)

V. N. Adrov

2012-07-01

Full Text Available Most cpu consuming tasks in photogrammetric processing can be done in parallel. The algorithms take independent bits as input and produce independent bits as output. The independence of bits comes from the nature of such algorithms since images, stereopairs or small image blocks parts can be processed independently. Many photogrammetric algorithms are fully automatic and do not require human interference. Photogrammetric workstations can perform tie points measurements, DTM calculations, orthophoto construction, mosaicing and many other service operations in parallel using distributed calculations. Distributed calculations save time reducing several days calculations to several hours calculations. Modern trends in computer technology show the increase of cpu cores in workstations, speed increase in local networks, and as a result dropping the price of the supercomputers or computer clusters that can contain hundreds or even thousands of computing nodes. Common distributed processing in DPW is usually targeted for interactive work with a limited number of cpu cores and is not optimized for centralized administration. The bottleneck of common distributed computing in photogrammetry can be in the limited lan throughput and storage performance, since the processing of huge amounts of large raster images is needed.

Personal computer interface for temmperature measuring in the cutting process with turning

International Nuclear Information System (INIS)

Trajchevski, Neven; Filipovski, Velimir; Kuzinonovski, Mikolaj

2004-01-01

The computer development aided reserch systems in the investigations of the characteristics of the surface layar forms conditions for decreasing of the measuring uncertainty. Especially important is the fact that the usage of open and self made measuring systems accomplishes the demands for a total control of the research process. This paper describes an original personal computer interface which is used in the newly built computer aided reserrch system for temperatute measuring in the machining with turning. This interface consists of optically-coupled linear isolation amplifier and an analog to digital (A/D) converter. It is designed for measuring of the themo- voltage that is a generated from the natural thermocouple workpiece-cutting tool. That is achived by digitalizing the value of the thermo-voltage in data which is transmitted to the personal computer. The interface realization is a result of the research activity of the faculty of Mechanical Engineering and the Faculty of Electrical Engineering in Skopje.

PC as physics computer for LHC?

CERN Document Server

Jarp, S; Simmins, A; Yaari, R; Jarp, Sverre; Tang, Hong; Simmins, Antony; Yaari, Refael

1995-01-01

In the last five years, we have seen RISC workstations take over the computing scene that was once controlled by mainframes and supercomputers. In this paper we will argue that the same phenomenon might happen again. A project, active since March this year in the Physics Data Processing group of CERN's CN division is described where ordinary desktop PCs running Windows (NT and 3.11) have been used for creating an environment for running large LHC batch jobs (initially the DICE simulation job of Atlas). The problems encountered in porting both the CERN library and the specific Atlas codes are described together with some encouraging benchmark results when comparing to existing RISC workstations in use by the Atlas collaboration. The issues of establishing the batch environment (Batch monitor, staging software, etc.) are also covered. Finally a quick extrapolation of commodity computing power available in the future is touched upon to indicate what kind of cost envelope could be sufficient for the simulation fa...

Study on Thermal Conductivity of Personal Computer Aluminum-Magnesium Alloy Casing

Science.gov (United States)

Liao, MeiHong

With the rapid development of computer technology, micro-state atoms by simulating the movement of material to analyze the nature of the macro-state have become an important subject. Materials, especially aluminium-magnesium alloy materials, often used in personal computer case, this article puts forward heat conduction model of the material, and numerical methods of heat transfer performance of the material.

Computers and Communications. Improving the Employability of Persons with Handicaps.

Science.gov (United States)

Deitel, Harvey M.

1984-01-01

Reviews applications of computer and communications technologies for persons with visual, hearing, physical, speech, and language impairments, as well as the effects of technologies on transportation, work at home, education, and other aspects affecting the employment of the disabled. (SK)

Providing disabled persons in developing countries access to computer games through a novel gaming input device

CSIR Research Space (South Africa)

Smith, Andrew C

2011-01-01

Full Text Available A novel input device is presented for use with a personal computer by persons with physical disabilities who would otherwise not be able to enjoy computer gaming. This device is simple to manufacture and low in cost. A gaming application...

Assessment of a cooperative workstation.

Science.gov (United States)

Beuscart, R J; Molenda, S; Souf, N; Foucher, C; Beuscart-Zephir, M C

1996-01-01

Groupware and new Information Technologies have now made it possible for people in different places to work together in synchronous cooperation. Very often, designers of this new type of software are not provided with a model of the common workspace, which is prejudicial to software development and its acceptance by potential users. The authors take the example of a task of medical co-diagnosis, using a multi-media communication workstation. Synchronous cooperative work is made possible by using local ETHERNET or public ISDN Networks. A detailed ergonomic task analysis studies the cognitive functioning of the physicians involved, compares their behaviour in the normal and the mediatized situations, and leads to an interpretation of the likely causes for success or failure of CSCW tools.

The BioPhotonics Workstation: from university research to commercial prototype

DEFF Research Database (Denmark)

Glückstad, Jesper

I will outline the specifications of the compact BioPhotonics Workstation we recently have developed that utilizes high-speed spatial light modulation to generate an array of reconfigurable laser-traps making 3D real-time optical manipulation of advanced structures possible with the use of joysti...

USAGE OF STANDARD PERSONAL COMPUTER PORTS FOR DESIGNING OF THE DOUBLE REDUNDANT FAULT-TOLERANT COMPUTER CONTROL SYSTEMS

Directory of Open Access Journals (Sweden)

Rafig SAMEDOV

2005-01-01

Full Text Available In this study, for designing of the fault-tolerant control systems by using standard personal computers, the ports have been investigated, different structure versions have been designed and the method for choosing of an optimal structure has been suggested. In this scope, first of all, the ÇİFTYAK system has been defined and its work principle has been determined. Then, data transmission ports of the standard personal computers have been classified and analyzed. After that, the structure versions have been designed and evaluated according to the used data transmission methods, the numbers of ports and the criterions of reliability, performance, truth, control and cost. Finally, the method for choosing of the most optimal structure version has been suggested.

xdamp Version 3: An IDL reg-sign-based data and image manipulation program

International Nuclear Information System (INIS)

Ballard, W.P.

1998-05-01

The original DAMP (DAta Manipulation Program) was written by Mark Hedemann of Sandia National Laboratories and used the CA-DISSPLA trademark (available from Computer Associates International, Inc., Garden City, NY) graphics package as its engine. It was used to plot, modify, and otherwise manipulate the one-dimensional data waveforms (data vs. time) from a wide variety of accelerators. With the waning of CA-DISSPLA and the increasing popularity of Unix reg-sign-based workstations, a replacement was needed. This package uses the IDL reg-sign software, available from Research Systems Incorporated in Boulder, Colorado, as the engine, and creates a set of widgets to manipulate the data in a manner similar to the original DAMP and earlier versions of xdamp. IDL is currently supported on a wide variety of Unix platforms such as IBM reg-sign workstations, Hewlett Packard workstations, SUN reg-sign workstations, Microsoft reg-sign Windows trademark computers, Macintosh reg-sign computers and Digital Equipment Corporation VMS reg-sign and Alpha reg-sign systems. Thus, xdamp is portable across many platforms. The author has verified operation, albeit with some minor IDL bugs, on personal computers using Windows 95 and Windows NT; IBM Unix platforms; and DEC alpha and VMS systems; HP 9000/700 series workstations; and Macintosh computers, both regular and PowerPC trademark versions. Version 3 adds the capability to manipulate images to the original xdamp capabilities

Computer-based versus in-person interventions for preventing and reducing stress in workers.

Science.gov (United States)

Kuster, Anootnara Talkul; Dalsbø, Therese K; Luong Thanh, Bao Yen; Agarwal, Arnav; Durand-Moreau, Quentin V; Kirkehei, Ingvild

2017-08-30

Chronic exposure to stress has been linked to several negative physiological and psychological health outcomes. Among employees, stress and its associated effects can also result in productivity losses and higher healthcare costs. In-person (face-to-face) and computer-based (web- and mobile-based) stress management interventions have been shown to be effective in reducing stress in employees compared to no intervention. However, it is unclear if one form of intervention delivery is more effective than the other. It is conceivable that computer-based interventions are more accessible, convenient, and cost-effective. To compare the effects of computer-based interventions versus in-person interventions for preventing and reducing stress in workers. We searched CENTRAL, MEDLINE, PubMed, Embase, PsycINFO, NIOSHTIC, NIOSHTIC-2, HSELINE, CISDOC, and two trials registers up to February 2017. We included randomised controlled studies that compared the effectiveness of a computer-based stress management intervention (using any technique) with a face-to-face intervention that had the same content. We included studies that measured stress or burnout as an outcome, and used workers from any occupation as participants. Three authors independently screened and selected 75 unique studies for full-text review from 3431 unique reports identified from the search. We excluded 73 studies based on full-text assessment. We included two studies. Two review authors independently extracted stress outcome data from the two included studies. We contacted study authors to gather additional data. We used standardised mean differences (SMDs) with 95% confidence intervals (CIs) to report study results. We did not perform meta-analyses due to variability in the primary outcome and considerable statistical heterogeneity. We used the GRADE approach to rate the quality of the evidence. Two studies met the inclusion criteria, including a total of 159 participants in the included arms of the studies

Framework Programmable Platform for the Advanced Software Development Workstation (FPP/ASDW). Demonstration framework document. Volume 1: Concepts and activity descriptions

Science.gov (United States)

Mayer, Richard J.; Blinn, Thomas M.; Dewitte, Paul S.; Crump, John W.; Ackley, Keith A.

1992-01-01

The Framework Programmable Software Development Platform (FPP) is a project aimed at effectively combining tool and data integration mechanisms with a model of the software development process to provide an intelligent integrated software development environment. Guided by the model, this system development framework will take advantage of an integrated operating environment to automate effectively the management of the software development process so that costly mistakes during the development phase can be eliminated. The Advanced Software Development Workstation (ASDW) program is conducting research into development of advanced technologies for Computer Aided Software Engineering (CASE).

Emulating conventional operator interfaces on window-based workstations

International Nuclear Information System (INIS)

Carr, G.P.

1990-01-01

This paper explores an approach to support the LAMPF and PSR control systems on VAX/VMS workstations using DECwindows and VI Corporation Data Views as the operator interface. The PSR control system was recently turned over to MP division and the two control-system staffs were merged into one group. One of the goals of this new group is to develop a common workstation-based operator console and interface which can be used in a single control room controlling both the linac and proton storage ring. The new console operator interface will need a high-level graphics toolkit for its implementation. During the conversion to the new consoles it will also probably be necessary to write a package to emulate the current operator interfaces at the software level. This paper describes a project to evaluate the appropriateness of VI Corporation's Data Views graphics package for use in the LAMPF control-system environment by using it to write an emulation of the LAMPF touch-panel interface to a large LAMPF control-system application program. A secondary objective of this project was to explore any productivity increases that might be realized by using an object-oriented graphics package and graphics editor. (orig.)

Copyright and personal use of CERN’s computing infrastructure

CERN Multimedia

IT Department

2009-01-01

(La version française sera en ligne prochainement)The rules covering the personal use of CERN’s computing infrastructure are defined in Operational Circular No. 5 and its Subsidiary Rules (see http://cern.ch/ComputingRules). All users of CERN’s computing infrastructure must comply with these rules, whether they access CERN’s computing facilities from within the Organization’s site or at another location. In particular, OC5 clause 17 requires that proprietary rights (the rights in software, music, video, etc.) must be respected. The user is liable for damages resulting from non-compliance. Recently, there have been several violations of OC5, where copyright material was discovered on public world-readable disk space. Please ensure that all material under your responsibility (in particular in files owned by your account) respects proprietary rights, including with respect to the restriction of access by third parties. CERN Security Team

Computer assisted radiology

International Nuclear Information System (INIS)

Lemke, H.U.; Jaffe, C.C.; Felix, R.

1993-01-01

The proceedings of the CAR'93 symposium present the 126 oral papers and the 58 posters contributed to the four Technical Sessions entitled: (1) Image Management, (2) Medical Workstations, (3) Digital Image Generation - DIG, and (4) Application Systems - AS. Topics discussed in Session (1) are: picture archiving and communication systems, teleradiology, hospital information systems and radiological information systems, technology assessment and implications, standards, and data bases. Session (2) deals with computer vision, computer graphics, design and application, man computer interaction. Session (3) goes into the details of the diagnostic examination methods such as digital radiography, MRI, CT, nuclear medicine, ultrasound, digital angiography, and multimodality imaging. Session (4) is devoted to computer-assisted techniques, as there are: computer assisted radiological diagnosis, knowledge based systems, computer assisted radiation therapy and computer assisted surgical planning. (UWA). 266 figs [de

Does computer-synthesized speech manifest personality? Experimental tests of recognition, similarity-attraction, and consistency-attraction.

Science.gov (United States)

Nass, C; Lee, K M

2001-09-01

Would people exhibit similarity-attraction and consistency-attraction toward unambiguously computer-generated speech even when personality is clearly not relevant? In Experiment 1, participants (extrovert or introvert) heard a synthesized voice (extrovert or introvert) on a book-buying Web site. Participants accurately recognized personality cues in text to speech and showed similarity-attraction in their evaluation of the computer voice, the book reviews, and the reviewer. Experiment 2, in a Web auction context, added personality of the text to the previous design. The results replicated Experiment 1 and demonstrated consistency (voice and text personality)-attraction. To maximize liking and trust, designers should set parameters, for example, words per minute or frequency range, that create a personality that is consistent with the user and the content being presented.

Parallelized computation for computer simulation of electrocardiograms using personal computers with multi-core CPU and general-purpose GPU.

Science.gov (United States)

Shen, Wenfeng; Wei, Daming; Xu, Weimin; Zhu, Xin; Yuan, Shizhong

2010-10-01

Biological computations like electrocardiological modelling and simulation usually require high-performance computing environments. This paper introduces an implementation of parallel computation for computer simulation of electrocardiograms (ECGs) in a personal computer environment with an Intel CPU of Core (TM) 2 Quad Q6600 and a GPU of Geforce 8800GT, with software support by OpenMP and CUDA. It was tested in three parallelization device setups: (a) a four-core CPU without a general-purpose GPU, (b) a general-purpose GPU plus 1 core of CPU, and (c) a four-core CPU plus a general-purpose GPU. To effectively take advantage of a multi-core CPU and a general-purpose GPU, an algorithm based on load-prediction dynamic scheduling was developed and applied to setting (c). In the simulation with 1600 time steps, the speedup of the parallel computation as compared to the serial computation was 3.9 in setting (a), 16.8 in setting (b), and 20.0 in setting (c). This study demonstrates that a current PC with a multi-core CPU and a general-purpose GPU provides a good environment for parallel computations in biological modelling and simulation studies. Copyright 2010 Elsevier Ireland Ltd. All rights reserved.

In person versus computer screening for intimate partner violence among pregnant patients.

Science.gov (United States)

Chang, Judy C; Dado, Diane; Schussler, Sara; Hawker, Lynn; Holland, Cynthia L; Burke, Jessica G; Cluss, Patricia A

2012-09-01

To compare in person versus computerized screening for intimate partner violence (IPV) in a hospital-based prenatal clinic and explore women's assessment of the screening methods. We compared patient IPV disclosures on a computerized questionnaire to audio-taped first obstetric visits with an obstetric care provider and performed semi-structured interviews with patient participants who reported experiencing IPV. Two-hundred and fifty patient participants and 52 provider participants were in the study. Ninety-one (36%) patients disclosed IPV either via computer or in person. Of those who disclosed IPV, 60 (66%) disclosed via both methods, but 31 (34%) disclosed IPV via only one of the two methods. Twenty-three women returned for interviews. They recommended using both types together. While computerized screening was felt to be non-judgmental and more anonymous, in person screening allowed for tailored questioning and more emotional connection with the provider. Computerized screening allowed disclosure without fear of immediate judgment. In person screening allows more flexibility in wording of questions regarding IPV and opportunity for interpersonal rapport. Both computerized or self-completed screening and in person screening is recommended. Providers should address IPV using non-judgmental, descriptive language, include assessments for psychological IPV, and repeat screening in person, even if no patient disclosure occurs via computer. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

A data acquisition system based on a personal computer

International Nuclear Information System (INIS)

Omata, K.; Fujita, Y.; Yoshikawa, N.; Sekiguchi, M.; Shida, Y.

1991-07-01

A versatile and flexible data acquisition system KODAQ (Kakuken Online Data AcQuisition system) has been developed. The system runs with CAMAC and a most popular Japanese personal computer, PC9801 (NEC), similar to the IBM PC/AT. The system is designed to set up easily a data acquisition system for various kinds of nuclear-physics experiments. (author)

The University of Michigan's Computer-Aided Engineering Network.

Science.gov (United States)

Atkins, D. E.; Olsen, Leslie A.

1986-01-01

Presents an overview of the Computer-Aided Engineering Network (CAEN) of the University of Michigan. Describes its arrangement of workstations, communication networks, and servers. Outlines the factors considered in hardware and software decision making. Reviews the program's impact on students. (ML)

A workstation-integrated peer review quality assurance program: pilot study

International Nuclear Information System (INIS)

O’Keeffe, Margaret M; Davis, Todd M; Siminoski, Kerry

2013-01-01

The surrogate indicator of radiological excellence that has become accepted is consistency of assessments between radiologists, and the technique that has become the standard for evaluating concordance is peer review. This study describes the results of a workstation-integrated peer review program in a busy outpatient radiology practice. Workstation-based peer review was performed using the software program Intelerad Peer Review. Cases for review were randomly chosen from those being actively reported. If an appropriate prior study was available, and if the reviewing radiologist and the original interpreting radiologist had not exceeded review targets, the case was scored using the modified RADPEER system. There were 2,241 cases randomly assigned for peer review. Of selected cases, 1,705 (76%) were interpreted. Reviewing radiologists agreed with prior reports in 99.1% of assessments. Positive feedback (score 0) was given in three cases (0.2%) and concordance (scores of 0 to 2) was assigned in 99.4%, similar to reported rates of 97.0% to 99.8%. Clinically significant discrepancies (scores of 3 or 4) were identified in 10 cases (0.6%). Eighty-eight percent of reviewed radiologists found the reviews worthwhile, 79% found scores appropriate, and 65% felt feedback was appropriate. Two-thirds of radiologists found case rounds discussing significant discrepancies to be valuable. The workstation-based computerized peer review process used in this pilot project was seamlessly incorporated into the normal workday and met most criteria for an ideal peer review system. Clinically significant discrepancies were identified in 0.6% of cases, similar to published outcomes using the RADPEER system. Reviewed radiologists felt the process was worthwhile

A workstation-integrated peer review quality assurance program: pilot study

Science.gov (United States)

2013-01-01

Background The surrogate indicator of radiological excellence that has become accepted is consistency of assessments between radiologists, and the technique that has become the standard for evaluating concordance is peer review. This study describes the results of a workstation-integrated peer review program in a busy outpatient radiology practice. Methods Workstation-based peer review was performed using the software program Intelerad Peer Review. Cases for review were randomly chosen from those being actively reported. If an appropriate prior study was available, and if the reviewing radiologist and the original interpreting radiologist had not exceeded review targets, the case was scored using the modified RADPEER system. Results There were 2,241 cases randomly assigned for peer review. Of selected cases, 1,705 (76%) were interpreted. Reviewing radiologists agreed with prior reports in 99.1% of assessments. Positive feedback (score 0) was given in three cases (0.2%) and concordance (scores of 0 to 2) was assigned in 99.4%, similar to reported rates of 97.0% to 99.8%. Clinically significant discrepancies (scores of 3 or 4) were identified in 10 cases (0.6%). Eighty-eight percent of reviewed radiologists found the reviews worthwhile, 79% found scores appropriate, and 65% felt feedback was appropriate. Two-thirds of radiologists found case rounds discussing significant discrepancies to be valuable. Conclusions The workstation-based computerized peer review process used in this pilot project was seamlessly incorporated into the normal workday and met most criteria for an ideal peer review system. Clinically significant discrepancies were identified in 0.6% of cases, similar to published outcomes using the RADPEER system. Reviewed radiologists felt the process was worthwhile. PMID:23822583

Functionalized 2PP structures for the BioPhotonics Workstation

DEFF Research Database (Denmark)

Matsuoka, Tomoyo; Nishi, Masayuki; Sakakura, Masaaki

2011-01-01

In its standard version, our BioPhotonics Workstation (BWS) can generate multiple controllable counter-propagating beams to create real-time user-programmable optical traps for stable three-dimensional control and manipulation of a plurality of particles. The combination of the platform with micr...... on the BWS platform by functionalizing them with silica-based sol-gel materials inside which dyes can be entrapped....

Sixties Counterculture and the Personal Computer (What the Dormouse Said: How the Sixties Counterculture Shaped the Personal Computer Industry)

International Nuclear Information System (INIS)

Markoff, John

2006-01-01

The Internet is arguably the largest accumulation of information in one place, yet its own beginnings remain largely undocumented. In researching his recent book, John Markoff collected oral histories from many of the Stanford-area researchers whose technological inventions defined the both modern internet and personal computer. In his talk, Markoff will explore the role that the counterculture and anti war movements of the 1960s and 1970s played in the work of these researchers as they created what would later be called the 'world's largest legal accumulation of wealth.'

Habitat Demonstration Unit Medical Operations Workstation Upgrades

Science.gov (United States)

Trageser, Katherine H.

2011-01-01

This paper provides an overview of the design and fabrication associated with upgrades for the Medical Operations Workstation in the Habitat Demonstration Unit. The work spanned a ten week period. The upgrades will be used during the 2011 Desert Research and Technology Studies (Desert RATS) field campaign. Upgrades include a deployable privacy curtain system, a deployable tray table, an easily accessible biological waste container, reorganization and labeling of the medical supplies, and installation of a retractable camera. All of the items were completed within the ten week period.

Some Ideas on the Microcomputer and the Information/Knowledge Workstation.

Science.gov (United States)

Boon, J. A.; Pienaar, H.

1989-01-01

Identifies the optimal goal of knowledge workstations as the harmony of technology and human decision-making behaviors. Two types of decision-making processes are described and the application of each type to experimental and/or operational situations is discussed. Suggestions for technical solutions to machine-user interfaces are then offered.…

Parallel computers and three-dimensional computational electromagnetics

International Nuclear Information System (INIS)

Madsen, N.K.

1994-01-01

The authors have continued to enhance their ability to use new massively parallel processing computers to solve time-domain electromagnetic problems. New vectorization techniques have improved the performance of their code DSI3D by factors of 5 to 15, depending on the computer used. New radiation boundary conditions and far-field transformations now allow the computation of radar cross-section values for complex objects. A new parallel-data extraction code has been developed that allows the extraction of data subsets from large problems, which have been run on parallel computers, for subsequent post-processing on workstations with enhanced graphics capabilities. A new charged-particle-pushing version of DSI3D is under development. Finally, DSI3D has become a focal point for several new Cooperative Research and Development Agreement activities with industrial companies such as Lockheed Advanced Development Company, Varian, Hughes Electron Dynamics Division, General Atomic, and Cray

PERKAM: Personalized Knowledge Awareness Map for Computer Supported Ubiquitous Learning

Science.gov (United States)

El-Bishouty, Moushir M.; Ogata, Hiroaki; Yano, Yoneo

2007-01-01

This paper introduces a ubiquitous computing environment in order to support the learners while doing tasks; this environment is called PERKAM (PERsonalized Knowledge Awareness Map). PERKAM allows the learners to share knowledge, interact, collaborate, and exchange individual experiences. It utilizes the RFID ubiquities technology to detect the…

Task Selection, Task Switching and Multitasking during Computer-Based Independent Study

Science.gov (United States)

Judd, Terry

2015-01-01

Detailed logs of students' computer use, during independent study sessions, were captured in an open-access computer laboratory. Each log consisted of a chronological sequence of tasks representing either the application or the Internet domain displayed in the workstation's active window. Each task was classified using a three-tier schema…

Interactive computer graphics applications for compressible aerodynamics

Science.gov (United States)

Benson, Thomas J.

1994-01-01

Three computer applications have been developed to solve inviscid compressible fluids problems using interactive computer graphics. The first application is a compressible flow calculator which solves for isentropic flow, normal shocks, and oblique shocks or centered expansions produced by two dimensional ramps. The second application couples the solutions generated by the first application to a more graphical presentation of the results to produce a desk top simulator of three compressible flow problems: 1) flow past a single compression ramp; 2) flow past two ramps in series; and 3) flow past two opposed ramps. The third application extends the results of the second to produce a design tool which solves for the flow through supersonic external or mixed compression inlets. The applications were originally developed to run on SGI or IBM workstations running GL graphics. They are currently being extended to solve additional types of flow problems and modified to operate on any X-based workstation.

Improving operational safety management through probabilistic safety assessment on personal computers

International Nuclear Information System (INIS)

1988-10-01

The Technical Committee Meeting considered the current effort in the implementation and use of PSA information for day-to-day operational safety management on Personal Computers. Due to the very recent development of the necessary hardware and software for Personal Computers, the application of PSA information for day-to-day operational safety management on PCs is essentially still in a pioneering stage. There is at present only one such system for end users existing, the PRISIM (Plant Risk Status Information Management) program for which a limited practical application experience is available. Others are still in the development stage. The main aim of the Technical Committee Meeting was to discuss the present status of PSA based systems for operational safety management support on small computers, to consider practical aspects when implementing these systems into a nuclear installation and to address problems related to the further work in the area. A separate abstract was prepared for the summary of the Technical Committee Meeting and for the 8 papers presented by the participants. Refs, figs and tabs

A parallel solution to the cutting stock problem for a cluster of workstations

Energy Technology Data Exchange (ETDEWEB)

Nicklas, L.D.; Atkins, R.W.; Setia, S.V.; Wang, P.Y. [George Mason Univ., Fairfax, VA (United States)

1996-12-31

This paper describes the design and implementation of a solution to the constrained 2-D cutting stock problem on a cluster of workstations. The constrained 2-D cutting stock problem is an irregular problem with a dynamically modified global data set and irregular amounts and patterns of communication. A replicated data structure is used for the parallel solution since the ratio of reads to writes is known to be large. Mutual exclusion and consistency are maintained using a token-based lazy consistency mechanism, and a randomized protocol for dynamically balancing the distributed work queue is employed. Speedups are reported for three benchmark problems executed on a cluster of workstations interconnected by a 10 Mbps Ethernet.

Distributed computing and nuclear reactor analysis

International Nuclear Information System (INIS)

Brown, F.B.; Derstine, K.L.; Blomquist, R.N.

1994-01-01

Large-scale scientific and engineering calculations for nuclear reactor analysis can now be carried out effectively in a distributed computing environment, at costs far lower than for traditional mainframes. The distributed computing environment must include support for traditional system services, such as a queuing system for batch work, reliable filesystem backups, and parallel processing capabilities for large jobs. All ANL computer codes for reactor analysis have been adapted successfully to a distributed system based on workstations and X-terminals. Distributed parallel processing has been demonstrated to be effective for long-running Monte Carlo calculations

A bench-top automated workstation for nucleic acid isolation from clinical sample types.

Science.gov (United States)

Thakore, Nitu; Garber, Steve; Bueno, Arial; Qu, Peter; Norville, Ryan; Villanueva, Michael; Chandler, Darrell P; Holmberg, Rebecca; Cooney, Christopher G

2018-04-18

Systems that automate extraction of nucleic acid from cells or viruses in complex clinical matrices have tremendous value even in the absence of an integrated downstream detector. We describe our bench-top automated workstation that integrates our previously-reported extraction method - TruTip - with our newly-developed mechanical lysis method. This is the first report of this method for homogenizing viscous and heterogeneous samples and lysing difficult-to-disrupt cells using "MagVor": a rotating magnet that rotates a miniature stir disk amidst glass beads confined inside of a disposable tube. Using this system, we demonstrate automated nucleic acid extraction from methicillin-resistant Staphylococcus aureus (MRSA) in nasopharyngeal aspirate (NPA), influenza A in nasopharyngeal swabs (NPS), human genomic DNA from whole blood, and Mycobacterium tuberculosis in NPA. The automated workstation yields nucleic acid with comparable extraction efficiency to manual protocols, which include commercially-available Qiagen spin column kits, across each of these sample types. This work expands the scope of applications beyond previous reports of TruTip to include difficult-to-disrupt cell types and automates the process, including a method for removal of organics, inside a compact bench-top workstation. Copyright © 2018 Elsevier B.V. All rights reserved.

Binary black holes on a budget: simulations using workstations

International Nuclear Information System (INIS)

Marronetti, Pedro; Tichy, Wolfgang; Bruegmann, Bernd; Gonzalez, Jose; Hannam, Mark; Husa, Sascha; Sperhake, Ulrich

2007-01-01

Binary black hole simulations have traditionally been computationally very expensive: current simulations are performed in supercomputers involving dozens if not hundreds of processors, thus systematic studies of the parameter space of binary black hole encounters still seem prohibitive with current technology. Here we show how the multi-layered refinement level code BAM can be used on dual processor workstations to simulate certain binary black hole systems. BAM, based on the moving punctures method, provides grid structures composed of boxes of increasing resolution near the centre of the grid. In the case of binaries, the highest resolution boxes are placed around each black hole and they track them in their orbits until the final merger when a single set of levels surrounds the black hole remnant. This is particularly useful when simulating spinning black holes since the gravitational fields gradients are larger. We present simulations of binaries with equal mass black holes with spins parallel to the binary axis and intrinsic magnitude of S/m 2 = 0.75. Our results compare favourably to those of previous simulations of this particular system. We show that the moving punctures method produces stable simulations at maximum spatial resolutions up to M/160 and for durations of up to the equivalent of 20 orbital periods

Analyzing Robotic Kinematics Via Computed Simulations

Science.gov (United States)

Carnahan, Timothy M.

1992-01-01

Computing system assists in evaluation of kinematics of conceptual robot. Displays positions and motions of robotic manipulator within work cell. Also displays interactions between robotic manipulator and other objects. Results of simulation displayed on graphical computer workstation. System includes both off-the-shelf software originally developed for automotive industry and specially developed software. Simulation system also used to design human-equivalent hand, to model optical train in infrared system, and to develop graphical interface for teleoperator simulation system.

Software Engineering Techniques for Computer-Aided Learning.

Science.gov (United States)

Ibrahim, Bertrand

1989-01-01

Describes the process for developing tutorials for computer-aided learning (CAL) using a programing language rather than an authoring system. The workstation used is described, the use of graphics is discussed, the role of a local area network (LAN) is explained, and future plans are discussed. (five references) (LRW)

Stand by Me: Qualitative Insights into the Ease of Use of Adjustable Workstations.

Science.gov (United States)

Leavy, Justine; Jancey, Jonine

2016-01-01

Office workers sit for more than 80% of the work day making them an important target for work site health promotion interventions to break up prolonged sitting time. Adjustable workstations are one strategy used to reduce prolonged sitting time. This study provides both an employees' and employers' perspective into the advantages, disadvantages, practicality and convenience of adjustable workstations and how movement in the office can be further supported by organisations. This qualitative study was part of the Uprising pilot study. Employees were from the intervention arm of a two group (intervention n = 18 and control n = 18) study. Employers were the immediate line-manager of the employee. Data were collected via employee focus groups (n = 17) and employer individual interviews (n = 12). The majority of participants were female (n = 18), had healthy weight, and had a post-graduate qualification. All focus group discussions and interviews were recorded, transcribed verbatim and the data coded according to the content. Qualitative content analysis was conducted. Employee data identified four concepts: enhanced general wellbeing; workability and practicality; disadvantages of the retro-fit; and triggers to stand. Most employees (n = 12) reported enhanced general well-being, workability and practicality included less email exchange and positive interaction (n = 5), while the instability of the keyboard a commonly cited disadvantage. Triggers to stand included time and task based prompts. Employer data concepts included: general health and wellbeing; work engagement; flexibility; employee morale; and injury prevention. Over half of the employers (n = 7) emphasised back care and occupational health considerations as important, as well as increased level of staff engagement and strategies to break up prolonged periods of sitting. The focus groups highlight the perceived general health benefits from this short intervention, including opportunity to sit less and interact

Stand by Me: Qualitative Insights into the Ease of Use of Adjustable Workstations

Directory of Open Access Journals (Sweden)

Jonine Jancey

2016-08-01

Full Text Available Background: Office workers sit for more than 80% of the work day making them an important target for work site health promotion interventions to break up prolonged sitting time. Adjustable workstations are one strategy used to reduce prolonged sitting time. This study provides both an employees’ and employers’ perspective into the advantages, disadvantages, practicality and convenience of adjustable workstations and how movement in the office can be further supported by organisations. This qualitative study was part of the Uprising pilot study. Employees were from the intervention arm of a two group (intervention n = 18 and control n = 18 study. Employers were the immediate line-manager of the employee. Data were collected via employee focus groups (n = 17 and employer individual interviews (n = 12. The majority of participants were female (n = 18, had healthy weight, and had a post-graduate qualification. All focus group discussions and interviews were recorded, transcribed verbatim and the data coded according to the content. Qualitative content analysis was conducted. Results: Employee data identified four concepts: enhanced general wellbeing; workability and practicality; disadvantages of the retro-fit; and triggers to stand. Most employees (n = 12 reported enhanced general well-being, workability and practicality included less email exchange and positive interaction (n = 5, while the instability of the keyboard a commonly cited disadvantage. Triggers to stand included time and task based prompts. Employer data concepts included: general health and wellbeing; work engagement; flexibility; employee morale; and injury prevention. Over half of the employers (n = 7 emphasised back care and occupational health considerations as important, as well as increased level of staff engagement and strategies to break up prolonged periods of sitting. Discussion: The focus groups highlight the perceived general health benefits from this short

A self-taught artificial agent for multi-physics computational model personalization.

Science.gov (United States)

Neumann, Dominik; Mansi, Tommaso; Itu, Lucian; Georgescu, Bogdan; Kayvanpour, Elham; Sedaghat-Hamedani, Farbod; Amr, Ali; Haas, Jan; Katus, Hugo; Meder, Benjamin; Steidl, Stefan; Hornegger, Joachim; Comaniciu, Dorin

2016-12-01

Personalization is the process of fitting a model to patient data, a critical step towards application of multi-physics computational models in clinical practice. Designing robust personalization algorithms is often a tedious, time-consuming, model- and data-specific process. We propose to use artificial intelligence concepts to learn this task, inspired by how human experts manually perform it. The problem is reformulated in terms of reinforcement learning. In an off-line phase, Vito, our self-taught artificial agent, learns a representative decision process model through exploration of the computational model: it learns how the model behaves under change of parameters. The agent then automatically learns an optimal strategy for on-line personalization. The algorithm is model-independent; applying it to a new model requires only adjusting few hyper-parameters of the agent and defining the observations to match. The full knowledge of the model itself is not required. Vito was tested in a synthetic scenario, showing that it could learn how to optimize cost functions generically. Then Vito was applied to the inverse problem of cardiac electrophysiology and the personalization of a whole-body circulation model. The obtained results suggested that Vito could achieve equivalent, if not better goodness of fit than standard methods, while being more robust (up to 11% higher success rates) and with faster (up to seven times) convergence rate. Our artificial intelligence approach could thus make personalization algorithms generalizable and self-adaptable to any patient and any model. Copyright © 2016. Published by Elsevier B.V.

Computer Workstations: Desks

Science.gov (United States)

... Safety and Health Program Recommendations It's the Law Poster REGULATIONS Law and Regulations Standard Interpretations Training Requirements ... page requires that javascript be enabled for some elements to function correctly. Please contact the OSHA Directorate ...

Computer Workstations: Keyboards

Science.gov (United States)

... Safety and Health Program Recommendations It's the Law Poster REGULATIONS Law and Regulations Standard Interpretations Training Requirements ... page requires that javascript be enabled for some elements to function correctly. Please contact the OSHA Directorate ...

Proceedings of workshop on distributed computing and network

International Nuclear Information System (INIS)

Abe, F.; Yuasa, F.

1993-02-01

'Distributed Computing and Network' is one of hot topics in the field of computing. Recent progress in the computer technology is providing new paradigm for computing even in High Energy Physics. Particularly the workstation based computer system is opening new active field of computer application to sciences. The major topics discussed in this symposium are distributed computing and wide area research network for domestic and international link. The two days symposium provided so enough topics to foresee the next direction of our computing environment. 70 people have got together to discuss on these interesting thema as well as information exchange on the computer technologies. (J.P.N.)

A standardized non-instrumental tool for characterizing workstations concerned with exposure to engineered nanomaterials

Science.gov (United States)

Canu I, Guseva; C, Ducros; S, Ducamp; L, Delabre; S, Audignon-Durand; C, Durand; Y, Iwatsubo; D, Jezewski-Serra; Bihan O, Le; S, Malard; A, Radauceanu; M, Reynier; M, Ricaud; O, Witschger

2015-05-01

The French national epidemiological surveillance program EpiNano aims at surveying mid- and long-term health effects possibly related with occupational exposure to either carbon nanotubes or titanium dioxide nanoparticles (TiO2). EpiNano is limited to workers potentially exposed to these nanomaterials including their aggregates and agglomerates. In order to identify those workers during the in-field industrial hygiene visits, a standardized non-instrumental method is necessary especially for epidemiologists and occupational physicians unfamiliar with nanoparticle and nanomaterial exposure metrology. A working group, Quintet ExpoNano, including national experts in nanomaterial metrology and occupational hygiene reviewed available methods, resources and their practice in order to develop a standardized tool for conducting company industrial hygiene visits and collecting necessary information. This tool, entitled “Onsite technical logbook”, includes 3 parts: company, workplace, and workstation allowing a detailed description of each task, process and exposure surrounding conditions. This logbook is intended to be completed during the company industrial hygiene visit. Each visit is conducted jointly by an industrial hygienist and an epidemiologist of the program and lasts one or two days depending on the company size. When all collected information is computerized using friendly-using software, it is possible to classify workstations with respect to their potential direct and/or indirect exposure. Workers appointed to workstations classified as concerned with exposure are considered as eligible for EpiNano program and invited to participate. Since January 2014, the Onsite technical logbook has been used in ten company visits. The companies visited were mostly involved in research and development. A total of 53 workstations with potential exposure to nanomaterials were pre-selected and observed: 5 with TiO2, 16 with single-walled carbon nanotubes, 27 multiwalled

A standardized non-instrumental tool for characterizing workstations concerned with exposure to engineered nanomaterials

International Nuclear Information System (INIS)

I, Guseva Canu; S, Ducamp; L, Delabre; Y, Iwatsubo; D, Jezewski-Serra; C, Ducros; S, Audignon-Durand; C, Durand; O, Le Bihan; S, Malard; A, Radauceanu; M, Reynier; M, Ricaud; O, Witschger

2015-01-01

The French national epidemiological surveillance program EpiNano aims at surveying mid- and long-term health effects possibly related with occupational exposure to either carbon nanotubes or titanium dioxide nanoparticles (TiO 2 ). EpiNano is limited to workers potentially exposed to these nanomaterials including their aggregates and agglomerates. In order to identify those workers during the in-field industrial hygiene visits, a standardized non-instrumental method is necessary especially for epidemiologists and occupational physicians unfamiliar with nanoparticle and nanomaterial exposure metrology. A working group, Quintet ExpoNano, including national experts in nanomaterial metrology and occupational hygiene reviewed available methods, resources and their practice in order to develop a standardized tool for conducting company industrial hygiene visits and collecting necessary information. This tool, entitled “Onsite technical logbook”, includes 3 parts: company, workplace, and workstation allowing a detailed description of each task, process and exposure surrounding conditions. This logbook is intended to be completed during the company industrial hygiene visit. Each visit is conducted jointly by an industrial hygienist and an epidemiologist of the program and lasts one or two days depending on the company size. When all collected information is computerized using friendly-using software, it is possible to classify workstations with respect to their potential direct and/or indirect exposure. Workers appointed to workstations classified as concerned with exposure are considered as eligible for EpiNano program and invited to participate. Since January 2014, the Onsite technical logbook has been used in ten company visits. The companies visited were mostly involved in research and development. A total of 53 workstations with potential exposure to nanomaterials were pre-selected and observed: 5 with TiO 2 , 16 with single-walled carbon nanotubes, 27 multiwalled

Multi-objective optimization algorithms for mixed model assembly line balancing problem with parallel workstations

Directory of Open Access Journals (Sweden)

Masoud Rabbani

2016-12-01

Full Text Available This paper deals with mixed model assembly line (MMAL balancing problem of type-I. In MMALs several products are made on an assembly line while the similarity of these products is so high. As a result, it is possible to assemble several types of products simultaneously without any additional setup times. The problem has some particular features such as parallel workstations and precedence constraints in dynamic periods in which each period also effects on its next period. The research intends to reduce the number of workstations and maximize the workload smoothness between workstations. Dynamic periods are used to determine all variables in different periods to achieve efficient solutions. A non-dominated sorting genetic algorithm (NSGA-II and multi-objective particle swarm optimization (MOPSO are used to solve the problem. The proposed model is validated with GAMS software for small size problem and the performance of the foregoing algorithms is compared with each other based on some comparison metrics. The NSGA-II outperforms MOPSO with respect to some comparison metrics used in this paper, but in other metrics MOPSO is better than NSGA-II. Finally, conclusion and future research is provided.

Automatic data acquisition system of environmental radiation monitor with a personal computer

International Nuclear Information System (INIS)

Ohkubo, Tohru; Nakamura, Takashi.

1984-05-01

The automatic data acquisition system of environmental radiation monitor was developed in a low price by using a PET personal computer. The count pulses from eight monitors settled at four site boundaries were transmitted to a radiation control room by a signal transmission device and analyzed by the computer via 12 channel scaler and PET-CAMAC Interface for graphic display and printing. (author)

Functional magnetic resonance maps obtained by personal computer; Mapas de resonancia magnetica funcional obtenidos con PC

Energy Technology Data Exchange (ETDEWEB)

Gomez, F. j.; Manjon, J. V.; Robles, M. [Universidad Politecnica de Valencia (Spain); Marti-Bonmati, L.; Dosda, R. [Cinica Quiron. Valencia (Spain); Molla, E. [Universidad de Valencia (Spain)

2001-07-01

Functional magnetic resonance (fMR) is of special relevance in the analysis of certain types of brain activation. The present report describes the development of a simple software program for use with personal computers (PCs) that analyzes these images and provides functional activation maps. Activation maps are based on the temporal differences in oxyhemoglobin in tomographic images. To detect these differences, intensities registered repeatedly during brain control and activation are compared. The experiments were performed with a 1.5-Tesla MR unit. To verify the reliability of the program fMR studies were carried out in 4 healthy individuals (12 contiguous slices, 80 images per slice every 3.1 seconds for a total of 960 images). All the images were transferred to a PC and were processed pixel by pixel within each sequence to obtain an intensity/time curve. The statistical study of the results (Student's test and cross correlation analysis) made it possible to establish the activation of each pixel. The images were prepared using spatial filtering, temporal filtering, baseline correction, normalization and segmentation of the parenchyma. The postprocessing of the results involved the elimination of single pixels, superposition of an anatomical image of greater spatial resolution and anti-aliasing. The application (Xfun 1.0, Valencia, Spain) was developed in Microsoft Visual C++5.0 Developer Studio for Windows NT Workstation. As a representative example, the program took 8.2 seconds to calculate and present the results of the entire study (12 functional maps). In the motor and visual activation experiments, the activation corresponding to regions proximal to the central sulcus of the hemisphere contralateral to the hand that moved and in the occipital cortex were observed. While programs that calculate activation maps are available, the development of software for PCs running Microsoft Windows ensures several key features for its use on a daily basis: it is

Videoconferencing using workstations in the ATLAS collaboration

International Nuclear Information System (INIS)

Onions, C.; Blokzijl, K. Bos

1994-01-01

The ATLAS collaboration consists of about 1000 physicists from close to 100 institutes around the world. This number is expected to grow over the coming years. The authors realized that they needed to do something to allow people to participate in meetings held at CERN without having to travel and hence they started a pilot project in July, 1993 to look into this. Colleagues from Nikhef already had experience of international network meetings (e.g. RIPE) using standard UNIX workstations and public domain software tools using the MBONE, hence they investigated this as a first priority

Visual observation of digitalised signals by workstations

International Nuclear Information System (INIS)

Navratil, J.; Akiyama, A.; Mimashi, T.

1994-01-01

The idea to have on-line information about the behavior of betatron tune, as a first step to the future automatic control of TRISTAN accelerator tune, appeared near the end of 1991. At the same time, other suggestions concerning a rejuvenation of the existing Control System arose and therefore the newly created project ''System for monitoring betatron tune'' (SMBT) started with several goals: - to obtain new on-line information about the beam behavior during the acceleration time, - to test the way of possible extension and replacement of the existing control system of TRISTAN, - to get experience with the workstation and XWindow software

Use of personal computers in performing a linear modal analysis of a large finite-element model

International Nuclear Information System (INIS)

Wagenblast, G.R.

1991-01-01

This paper presents the use of personal computers in performing a dynamic frequency analysis of a large (2,801 degrees of freedom) finite-element model. Large model linear time history dynamic evaluations of safety related structures were previously restricted to mainframe computers using direct integration analysis methods. This restriction was a result of the limited memory and speed of personal computers. With the advances in memory capacity and speed of the personal computers, large finite-element problems now can be solved in the office in a timely and cost effective manner. Presented in three sections, this paper describes the procedure used to perform the dynamic frequency analysis of the large (2,801 degrees of freedom) finite-element model on a personal computer. Section 2.0 describes the structure and the finite-element model that was developed to represent the structure for use in the dynamic evaluation. Section 3.0 addresses the hardware and software used to perform the evaluation and the optimization of the hardware and software operating configuration to minimize the time required to perform the analysis. Section 4.0 explains the analysis techniques used to reduce the problem to a size compatible with the hardware and software memory capacity and configuration

X based interactive computer graphics applications for aerodynamic design and education

Science.gov (United States)

Benson, Thomas J.; Higgs, C. Fred, III

1995-01-01

Six computer applications packages have been developed to solve a variety of aerodynamic problems in an interactive environment on a single workstation. The packages perform classical one dimensional analysis under the control of a graphical user interface and can be used for preliminary design or educational purposes. The programs were originally developed on a Silicon Graphics workstation and used the GL version of the FORMS library as the graphical user interface. These programs have recently been converted to the XFORMS library of X based graphics widgets and have been tested on SGI, IBM, Sun, HP and PC-Lunix computers. The paper will show results from the new VU-DUCT program as a prime example. VU-DUCT has been developed as an educational package for the study of subsonic open and closed loop wind tunnels.

[Individual psychological features in patients with computer game addiction suffering and predisposed persons].

Science.gov (United States)

Kardashian, R A

2018-01-01

To study personality characteristics in adolescents with computer game addiction. The study included students of grades 7 to 10 at the age of 12-17 years (14.6±2.4 years), their parents and school teachers. The results of a study showed the following combination in patients: 'genophilic' type of DPT with schizoid personality accentuation and 'projection' type of psychological protection, and 'dignitophilic' type of DPT with labile personality accentuation and 'denial' type of PP.

PC as physics computer for LHC?

International Nuclear Information System (INIS)

Jarp, Sverre; Simmins, Antony; Tang, Hong

1996-01-01

In the last five years, we have seen RISC workstations take over the computing scene that was once controlled by mainframes and supercomputers. In this paper we will argue that the same phenomenon might happen again. A project, active since March this year in the Physics Data Processing group of CERN's CN division is described where ordinary desktop PCs running Windows (NT and 3.11) have been used for creating an environment for running large LHC batch jobs (initially the DICE simulation job of Atlas). The problems encountered in porting both the CERN library and the specific Atlas codes are described together with some encouraging benchmark results when comparing to existing to existing RISC workstation in use by the Atlas collaboration. The issues of establishing the batch environment (Batch monitor, staging software, etc) are also covered. Finally a quick extrapolation of commodity computing power available in the future is touched upon to indicate what kind of cost envelope could be sufficient for the simulation farms required by the LHC experiments. (author)

Pc as Physics Computer for Lhc ?

Science.gov (United States)

Jarp, Sverre; Simmins, Antony; Tang, Hong; Yaari, R.

In the last five years, we have seen RISC workstations take over the computing scene that was once controlled by mainframes and supercomputers. In this paper we will argue that the same phenomenon might happen again. A project, active since March this year in the Physics Data Processing group, of CERN's CN division is described where ordinary desktop PCs running Windows (NT and 3.11) have been used for creating an environment for running large LHC batch jobs (initially the DICE simulation job of Atlas). The problems encountered in porting both the CERN library and the specific Atlas codes are described together with some encouraging benchmark results when comparing to existing RISC workstations in use by the Atlas collaboration. The issues of establishing the batch environment (Batch monitor, staging software, etc.) are also covered. Finally a quick extrapolation of commodity computing power available in the future is touched upon to indicate what kind of cost envelope could be sufficient for the simulation farms required by the LHC experiments.

Field analysis: approach to the design of teleoperator workstation

International Nuclear Information System (INIS)

Saint-Jean, T.; Lescoat, D.A.

1986-04-01

Following a brief review of theoretical scope this paper will characterize a methodology to the design of teleoperation workstations. This methodology is illustrated by an example - field analysis of a telemanipulation task in a hot cell. Practical informations are given: operating strategy different from the written procedure, team work organization, different skills. Recommendations are suggested as regards the writing of procedures, the training of personnel and the work organisation

Talbot's method for the numerical inversion of Laplace transforms: an implementation for personal computers

International Nuclear Information System (INIS)

Garratt, T.J.

1989-05-01

Safety assessments of radioactive waste disposal require efficient computer models for the important processes. The present paper is based on an efficient computational technique which can be used to solve a wide variety of safety assessment models. It involves the numerical inversion of analytical solutions to the Laplace-transformed differential equations using a method proposed by Talbot. This method has been implemented on a personal computer in a user-friendly manner. The steps required to implement a particular transform and run the program are outlined. Four examples are described which illustrate the flexibility, accuracy and efficiency of the program. The improvements in computational efficiency described in this paper have application to the probabilistic safety assessment codes ESCORT and MASCOT which are currently under development. Also, it is hoped that the present work will form the basis of software for personal computers which could be used to demonstrate safety assessment procedures to a wide audience. (author)

Open source acceleration of wave optics simulations on energy efficient high-performance computing platforms

Science.gov (United States)

Beck, Jeffrey; Bos, Jeremy P.

2017-05-01

We compare several modifications to the open-source wave optics package, WavePy, intended to improve execution time. Specifically, we compare the relative performance of the Intel MKL, a CPU based OpenCV distribution, and GPU-based version. Performance is compared between distributions both on the same compute platform and between a fully-featured computing workstation and the NVIDIA Jetson TX1 platform. Comparisons are drawn in terms of both execution time and power consumption. We have found that substituting the Fast Fourier Transform operation from OpenCV provides a marked improvement on all platforms. In addition, we show that embedded platforms offer some possibility for extensive improvement in terms of efficiency compared to a fully featured workstation.

Development of a UNIX network compatible reactivity computer

International Nuclear Information System (INIS)

Sanchez, R.F.; Edwards, R.M.

1996-01-01

A state-of-the-art UNIX network compatible controller and UNIX host workstation with MATLAB/SIMULINK software were used to develop, implement, and validate a digital reactivity calculation. An objective of the development was to determine why a Macintosh-based reactivity computer reactivity output drifted intolerably

Effects of Dual Monitor Computer Work Versus Laptop Work on Cervical Muscular and Proprioceptive Characteristics of Males and Females.

Science.gov (United States)

Farias Zuniga, Amanda M; Côté, Julie N

2017-06-01

The effects of performing a 90-minute computer task with a laptop versus a dual monitor desktop workstation were investigated in healthy young male and female adults. Work-related musculoskeletal disorders are common among computer (especially female) users. Laptops have surpassed desktop computer sales, and working with multiple monitors has also become popular. However, few studies have provided objective evidence on how they affect the musculoskeletal system in both genders. Twenty-seven healthy participants (mean age = 24.6 years; 13 males) completed a 90-minute computer task while using a laptop or dual monitor (DualMon) desktop. Electromyography (EMG) from eight upper body muscles and visual strain were measured throughout the task. Neck proprioception was tested before and after the computer task using a head-repositioning test. EMG amplitude (root mean square [RMS]), variability (coefficients of variation [CV]), and normalized mutual information (NMI) were computed. Visual strain ( p computer workstation designs.

Distributed interactive graphics applications in computational fluid dynamics

International Nuclear Information System (INIS)

Rogers, S.E.; Buning, P.G.; Merritt, F.J.

1987-01-01

Implementation of two distributed graphics programs used in computational fluid dynamics is discussed. Both programs are interactive in nature. They run on a CRAY-2 supercomputer and use a Silicon Graphics Iris workstation as the front-end machine. The hardware and supporting software are from the Numerical Aerodynamic Simulation project. The supercomputer does all numerically intensive work and the workstation, as the front-end machine, allows the user to perform real-time interactive transformations on the displayed data. The first program was written as a distributed program that computes particle traces for fluid flow solutions existing on the supercomputer. The second is an older post-processing and plotting program modified to run in a distributed mode. Both programs have realized a large increase in speed over that obtained using a single machine. By using these programs, one can learn quickly about complex features of a three-dimensional flow field. Some color results are presented

A flexible image archiving system using a personal computer and optical disk

International Nuclear Information System (INIS)

Parkin, A.; Norwood, H.; Hall, A.J.

1989-01-01

The authors describe the application of a personal computer and optical disk as an image archiving device, which brings the advantages of large capacity, low cost and savings on storage space. (author)

Design and Development of an Integrated Workstation Automation Hub

Energy Technology Data Exchange (ETDEWEB)

Weber, Andrew; Ghatikar, Girish; Sartor, Dale; Lanzisera, Steven

2015-03-30

Miscellaneous Electronic Loads (MELs) account for one third of all electricity consumption in U.S. commercial buildings, and are drivers for a significant energy use in India. Many of the MEL-specific plug-load devices are concentrated at workstations in offices. The use of intelligence, and integrated controls and communications at the workstation for an Office Automation Hub – offers the opportunity to improve both energy efficiency and occupant comfort, along with services for Smart Grid operations. Software and hardware solutions are available from a wide array of vendors for the different components, but an integrated system with interoperable communications is yet to be developed and deployed. In this study, we propose system- and component-level specifications for the Office Automation Hub, their functions, and a prioritized list for the design of a proof-of-concept system. Leveraging the strength of both the U.S. and India technology sectors, this specification serves as a guide for researchers and industry in both countries to support the development, testing, and evaluation of a prototype product. Further evaluation of such integrated technologies for performance and cost is necessary to identify the potential to reduce energy consumptions in MELs and to improve occupant comfort.

Calculation of transmission and other functionals from evaluated data in ENDF format by means of personal computers

International Nuclear Information System (INIS)

Vertes, P.

1991-04-01

The FDMXPC program package was developed on the basis of the program system FEDMIX written for mainframe computers. The new program package for personal computers was developed for the interpretation of neutron transmission experiments and for producing group averaged infinite diluted and self-shielded cross sections, starting from evaluated data in ENDF format. The package was written for different FORTRAN compilers residing in personal computers under MS-DOS. (R.P.) 12 refs

Predicting cycle time distributions for integrated processing workstations : an aggregate modeling approach

NARCIS (Netherlands)

Veeger, C.P.L.; Etman, L.F.P.; Lefeber, A.A.J.; Adan, I.J.B.F.; Herk, van J.; Rooda, J.E.

2011-01-01

To predict cycle time distributions of integrated processing workstations, detailed simulation models are almost exclusively used; these models require considerable development and maintenance effort. As an alternative, we propose an aggregate model that is a lumped-parameter representation of the

Transmission of DICOM 3.0 type MR data to the personal computer in the hospital without PACS

International Nuclear Information System (INIS)

Lee, Seon Kyu; Kim, Hak Soo; Hwang, Hee Young; Kim, Ji Hye; Chung, Hyo Sun; Kim, Hyung Sik

1999-01-01

To transmit DICOM data to a personal computer in the hospital without PACS, and estimate the usefulness of digital image management and its convenience for physicians through transmitted file size, transmission time and quality of transmitted images. The raw data of three brain MRI and lumbar spine MRI were transmitted from an MR system to a personal computer via Ethernet TCP/IP connection. The file size and transmission time of transmitted images were measured according to the matrix number. Three board-certified radiologists compared the image quality of the transmitted and scanned images. The transmission of DICOM data to the personal computer was successful and the transmitted images and their header information were displayed by various personal computer-based DICOM viewing programs. The file size and transmission time of the 256 and 512 matrix images were 136 Kbyte, 2.17 seconds/slice and 520 Kbyte, 4.37 seconds/slice, respectively. All radiologists regarded the transmitted brain MRI images as superior. One radiologist considered the transmitted lumbar spine MRI images superior, while others decided that the quality of transmitted and scanned images was the same. The transmission of DICOM format image data to a personal computer through an appropriate DICOM receiving program is useful for managing digital images and convenient for physicians in the hospital without PACS

A Computer-Supported Method to Reveal and Assess Personal Professional Theories in Vocational Education

Science.gov (United States)

van den Bogaart, Antoine C. M.; Bilderbeek, Richel J. C.; Schaap, Harmen; Hummel, Hans G. K.; Kirschner, Paul A.

2016-01-01

This article introduces a dedicated, computer-supported method to construct and formatively assess open, annotated concept maps of Personal Professional Theories (PPTs). These theories are internalised, personal bodies of formal and practical knowledge, values, norms and convictions that professionals use as a reference to interpret and acquire…

Efficient Incremental Garbage Collection for Workstation/Server Database Systems

OpenAIRE

Amsaleg , Laurent; Gruber , Olivier; Franklin , Michael

1994-01-01

Projet RODIN; We describe an efficient server-based algorithm for garbage collecting object-oriented databases in a workstation/server environment. The algorithm is incremental and runs concurrently with client transactions, however, it does not hold any locks on data and does not require callbacks to clients. It is fault tolerant, but performs very little logging. The algorithm has been designed to be integrated into existing OODB systems, and therefore it works with standard implementation ...

Integrated model for line balancing with workstation inventory management

OpenAIRE

Dilip Roy; Debdip khan

2010-01-01

In this paper, we address the optimization of an integrated line balancing process with workstation inventory management. While doing so, we have studied the interconnection between line balancing and its conversion process. Almost each and every moderate to large manufacturing industry depends on a long and integrated supply chain, consisting of inbound logistic, conversion process and outbound logistic. In this sense an approach addresses a very general problem of integrated line balancing....

CUDA/GPU Technology : Parallel Programming For High Performance Scientific Computing

OpenAIRE

YUHENDRA; KUZE, Hiroaki; JOSAPHAT, Tetuko Sri Sumantyo

2009-01-01

[ABSTRACT]Graphics processing units (GP Us) originally designed for computer video cards have emerged as the most powerful chip in a high-performance workstation. In the high performance computation capabilities, graphic processing units (GPU) lead to much more powerful performance than conventional CPUs by means of parallel processing. In 2007, the birth of Compute Unified Device Architecture (CUDA) and CUDA-enabled GPUs by NVIDIA Corporation brought a revolution in the general purpose GPU a...

Evaluation of DEC`s GIGAswitch for distributed parallel computing

Energy Technology Data Exchange (ETDEWEB)

Chen, H.; Hutchins, J.; Brandt, J.

1993-10-01

One of Sandia`s research efforts is to reduce the end-to-end communication delay in a parallel-distributed computing environment. GIGAswitch is DEC`s implementation of a gigabit local area network based on switched FDDI technology. Using the GIGAswitch, the authors intend to minimize the medium access latency suffered by shared-medium FDDI technology. Experimental results show that the GIGAswitch adds 16.5 microseconds of switching and bridging delay to an end-to-end communication. Although the added latency causes a 1.8% throughput degradation and a 5% line efficiency degradation, the availability of dedicated bandwidth is much more than what is available to a workstation on a shared medium. For example, ten directly connected workstations each would have a dedicated bandwidth of 95 Mbps, but if they were sharing the FDDI bandwidth, each would have 10% of the total bandwidth, i.e., less than 10 Mbps. In addition, they have found that when there is no output port contention, the switch`s aggregate bandwidth will scale up to multiples of its port bandwidth. However, with output port contention, the throughput and latency performance suffered significantly. Their mathematical and simulation models indicate that the GIGAswitch line efficiency could be as low as 63% when there are nine input ports contending for the same output port. The data indicate that the delay introduced by contention at the server workstation is 50 times that introduced by the GIGAswitch. The authors conclude that the GIGAswitch meets the performance requirements of today`s high-end workstations and that the switched FDDI technology provides an alternative that utilizes existing workstation interfaces while increasing the aggregate bandwidth. However, because the speed of workstations is increasing by a factor of 2 every 1.5 years, the switched FDDI technology is only good as an interim solution.

Tablet computers and eBooks. Unlocking the potential for personal learning environments?

NARCIS (Netherlands)

Kalz, Marco

2012-01-01

Kalz, M. (2012, 9 May). Tablet computers and eBooks. Unlocking the potential for personal learning environments? Invited presentation during the annual conference of the European Association for Distance Learning (EADL), Noordwijkerhout, The Netherlands.

Reviews of computing technology: Software overview

Energy Technology Data Exchange (ETDEWEB)

Hartshorn, W.R.; Johnson, A.L.

1994-01-05

The Savannah River Site Computing Architecture states that the site computing environment will be standards-based, data-driven, and workstation-oriented. Larger server systems deliver needed information to users in a client-server relationship. Goals of the Architecture include utilizing computing resources effectively, maintaining a high level of data integrity, developing a robust infrastructure, and storing data in such a way as to promote accessibility and usability. This document describes the current storage environment at Savannah River Site (SRS) and presents some of the problems that will be faced and strategies that are planned over the next few years.

Ergonomic assessment of musculoskeletal disorders risk among the computer users by Rapid Upper Limb Assessment method

Directory of Open Access Journals (Sweden)

Ehsanollah Habibi

2016-01-01

Conclusion: This study result showed that frequency of musculoskeletal problems in the neck, back, elbow, and wrist was generally high among our subjects, and ergonomic interventions such as computer workstation redesign, users educate about ergonomic principles computer with work, reduced working hours in computers with work must be carried out.

Analysis on the influence of supply method on a workstation with the help of dynamic simulation

Directory of Open Access Journals (Sweden)

Gavriluță Alin

2017-01-01

Full Text Available Considering the need of flexibility in any manufacturing process, the choice of the supply method of an assembly workstation can be a decision with instead influence on its performances. Using dynamic simulation, this article wants to compare the effect on a workstation cycle time of three different supply methods: supply on stock, supply in “Strike Zone” and synchronous supply. This study is part of an extended work that has the aim of compering by 3D layout design and dynamic simulation, different supply methods on an assembly line performances.

The use of mapped network drive to enhance the availability and accessibility of patient archive in ge-elscint Xpert workstations

International Nuclear Information System (INIS)

Chau; Kam Hung

2004-01-01

Purpose: To enhance the search and retrieval of patients' past record for clinical purpose. Methods: In the past, patient data was stored by MOD (Magnetic Optical Disk - Write Many Read Many). Its capacity is 327 MByte per side (654 MByte Total). In our department, each disk take up around 10 days of study. To search for patients' past record, we need to pick up a particular disk from a pile of MODs. With the advent of high speed network and high capacity hard disk, we have developed a method to put patients' past record on line so that the search was made easier and faster. The GE-Elscint Xpert Workstation is running on OS/2 Warp Connect Version 3 with inherent TCP/IP support. The current application is Apex Xpert Version 5.13. The Central Archive Unit is a 9 Gbyte Hard Disk which limited the on-line capacity of around 6 months. The Workstation was connected to a Windows NT based PC on the network. A folder was created and shared for network access. To make resources sharing possible. We installed OS/2Warp Connect software - IBM Peer for OS/2 on the Xpert Workstation. In addition, the Xpert based system was configured to be able to initiate communication with remote TCP/IP and ApexNet nodes. On the Xpert Workstation, Ne apply drive mapping by assigning a drive letter to the remote share located on the Windows NT based PC. To map a shared folder to a drive letter, specify the drive letter and the share's name on the Net Use command. For example, net use s: //WinNTPC /DataFilesmaps the DataFiles share on the WinNTPC computer to drive S. If any folder in the share's path contains a space, you must put the entire path, including the opening double backslash (//), in quotation marks. Connections to NT resources can also be made through the OS/2 network browser, the Sharing and Connecting Graphic User Interface on the Desktop. An active user ID and password authorizes the user to browse and use shared drives. With this mapped drive, we can copy patient record to it. The

Personal computer security: part 1. Firewalls, antivirus software, and Internet security suites.

Science.gov (United States)

Caruso, Ronald D

2003-01-01

Personal computer (PC) security in the era of the Health Insurance Portability and Accountability Act of 1996 (HIPAA) involves two interrelated elements: safeguarding the basic computer system itself and protecting the information it contains and transmits, including personal files. HIPAA regulations have toughened the requirements for securing patient information, requiring every radiologist with such data to take further precautions. Security starts with physically securing the computer. Account passwords and a password-protected screen saver should also be set up. A modern antivirus program can easily be installed and configured. File scanning and updating of virus definitions are simple processes that can largely be automated and should be performed at least weekly. A software firewall is also essential for protection from outside intrusion, and an inexpensive hardware firewall can provide yet another layer of protection. An Internet security suite yields additional safety. Regular updating of the security features of installed programs is important. Obtaining a moderate degree of PC safety and security is somewhat inconvenient but is necessary and well worth the effort. Copyright RSNA, 2003

Effectiveness of computer ergonomics interventions for an engineering company: a program evaluation.

Science.gov (United States)

Goodman, Glenn; Landis, James; George, Christina; McGuire, Sheila; Shorter, Crystal; Sieminski, Michelle; Wilson, Tamika

2005-01-01

Ergonomic principles at the computer workstation may reduce the occurrence of work related injuries commonly associated with intensive computer use. A program implemented in 2001 by an occupational therapist and a physical therapist utilized these preventative measures with education about ergonomics, individualized evaluations of computer workstations, and recommendations for ergonomic and environmental changes. This study examined program outcomes and perceived effectiveness based on review of documents, interviews, and surveys of the employees and the plant manager. The program was deemed successful as shown by 59% of all therapist recommendations and 74% of ergonomic recommendations being implemented by the company, with an 85% satisfaction rate for the ergonomic interventions and an overall employee satisfaction rate of 70%. Eighty-one percent of the physical problems reported by employees were resolved to their satisfaction one year later. Successful implementation of ergonomics programs depend upon effective communication and education of the consumers, and the support, cooperation and collaboration of management and employees.

Thermal load at workstations in the underground coal mining: Results of research carried out in 6 coal mines

Directory of Open Access Journals (Sweden)

Krzysztof Słota

2016-08-01

Full Text Available Background: Statistics shows that almost half of Polish extraction in underground mines takes place at workstations where temperature exceeds 28°C. The number of employees working in such conditions is gradually increasing, therefore, the problem of safety and health protection is still growing. Material and Methods: In the present study we assessed the heat load of employees at different workstations in the mining industry, taking into account current thermal conditions and work costs. The evaluation of energy cost of work was carried out in 6 coal mines. A total of 221 miners employed at different workstations were assessed. Individual groups of miners were characterized and thermal safety of the miners was assessed relying on thermal discomfort index. Results: The results of this study indicate considerable differences in the durations of analyzed work processes at individual workstations. The highest average energy cost was noted during the work performed in the forehead. The lowest value was found in the auxiliary staff. The calculated index of discomfort clearly indicated numerous situations in which the admissible range of thermal load exceeded the parameters of thermal load safe for human health. It should be noted that the values of average labor cost fall within the upper, albeit admissible, limits of thermal load. Conclusions: The results of the study indicate that in some cases work in mining is performed in conditions of thermal discomfort. Due to high variability and complexity of work conditions it becomes necessary to verify the workers’ load at different workstations, which largely depends on the environmental conditions and work organization, as well as on the performance of workers themselves. Med Pr 2016;67(4:477–498

Digital luminescence radiography using a chest phantom

International Nuclear Information System (INIS)

Lyttkens, K.; Kehler, M.; Andersson, B.; Carlsen, S.; Ebbesen, A.; Hochbergs, P.; Stroembaeck, A.

1993-01-01

With the introduction of picture and archiving communicating systems an alternative image display for the wards might be a personal computer (PC). The intention with this study was to evaluate the diagnostic image quality of the monitor of a PC compared to that of a workstation. Eighty-five digital radiographs of a chest phantom with simulated tumors in the mediastinum and right lung were saved on optical discs. The examinations were reviewed by 4 radiologists on a monitor at a workstation and at a PC, and receiver operating characteristic (ROC) curves were constructed. No significant difference was found between performance of the PC and the workstation. (orig.)

Different perspectives on the use of personal computers for technical analyses

International Nuclear Information System (INIS)

Libby, R.A.; Doherty, A.L.

1986-01-01

Personal computers (PCs) have widespread availability and use in many technical environments. The machines may have initially been justified for use as word processors or for data base management, but many technical applications are being performed and often the computer codes used in these technical analyses have been moved from large mainframe machines. The general feeling in the user community is that the free computer time on these machines justifies moving as many applications as possible from the large computer systems. Many of these PC applications cannot be justified if the total cost of using microcomputers is considered. A Hanford-wide local area network (LAN) is being established which allows individual PCs to be used as terminals to connect to mainframe computers at high data transfer rates (9600 baud). This system allows fast, easy connection to a variety of different computers with a few keystrokes. The LAN eliminates the problem of low-speed communication with mainframe computers and makes operation on the mainframes as simple as operation on the host PC, itself

Fast Calibration of Industrial Mobile Robots to Workstations using QR Codes

DEFF Research Database (Denmark)

Andersen, Rasmus Skovgaard; Damgaard, Jens Skov; Madsen, Ole

2013-01-01

is proposed. With this QR calibration, it is possible to calibrate an AIMM to a workstation in 3D in less than 1 second, which is significantly faster than existing methods. The accuracy of the calibration is ±4 mm. The method is modular in the sense that it directly supports integration and calibration...

Obstetrical ultrasound data-base management system by using personal computer

International Nuclear Information System (INIS)

Jeon, Hae Jeong; Park, Jeong Hee; Kim, Soo Nyung

1993-01-01

A computer program which performs obstetric calculations on Clipper Language using the data from ultrasonography was developed for personal computer. It was designed for fast assessment of fetal development, prediction of gestational age, and weight from ultrasonographic measurements which included biparietal diameter, femur length, gestational sac, occipito-frontal diameter, abdominal diameter, and etc. The Obstetrical-Ultrasound Data-Base Management System was tested for its performance. The Obstetrical-Ultrasound Data-Base Management System was very useful in patient management with its convenient data filing, easy retrieval of previous report, prompt but accurate estimation of fetal growth and skeletal anomaly and production of equation and growth curve for pregnant women

FORMING SCHOOLCHILD’S PERSONALITY IN COMPUTER STUDY LESSONS AT PRIMARY SCHOOL

Directory of Open Access Journals (Sweden)

Natalia Salan

2017-04-01

Full Text Available The influence of computer on the formation of primary schoolchildren’s personality and their implementing into learning activity are considered in the article. Based on the materials of state standards and the Law of Ukraine on Higher Education the concepts “computer”, “information culture” are defined, modern understanding of the concept “basics of computer literacy” is identified. The main task of school propaedeutic course in Computer Studies is defined. Interactive methods of activity are singled out. They are didactic games, designing, research, collaboration in pairs, and group interaction, etc. The essential characteristics of didactic game technologies are distinguished, the peculiarities of their use at primary school in Computer Study lessons are analyzed. Positive and negative aspects of using these technologies in Computer Study lessons are defined. The expediency of using game technologies while organizing students’ educational and cognitive activity in Computer Studies is substantiated. The idea to create a school course “Computer Studies at primary school” is caused by the wide introduction of computer technics into the educational system. Today’s schoolchild has to be able to use a computer as freely and easily as he can use a pen, a pencil or a ruler. That’s why it is advisable to start studying basics of Computer Studies at the primary school age. This course is intended for the pupils of the 2nd-4th forms. Firstly, it provides mastering practical skills of computer work and, secondly, it anticipates the development of children’s logical and algorithmic thinking styles. At these lessons students acquire practical skills to work with information on the computer. Having mastered the computer skills at primary school, children will be able to use it successfully in their work. In senior classes they will be able to realize acquired knowledge of the methods of work with information, ways of problem solving

Processing of evaluated neutron data files in ENDF format on personal computers

International Nuclear Information System (INIS)

Vertes, P.

1991-11-01

A computer code package - FDMXPC - has been developed for processing evaluated data files in ENDF format. The earlier version of this package is supplemented with modules performing calculations using Reich-Moore and Adler-Adler resonance parameters. The processing of evaluated neutron data files by personal computers requires special programming considerations outlined in this report. The scope of the FDMXPC program system is demonstrated by means of numerical examples. (author). 5 refs, 4 figs, 4 tabs

Los Alamos radiation transport code system on desktop computing platforms

International Nuclear Information System (INIS)

Briesmeister, J.F.; Brinkley, F.W.; Clark, B.A.; West, J.T.

1990-01-01

The Los Alamos Radiation Transport Code System (LARTCS) consists of state-of-the-art Monte Carlo and discrete ordinates transport codes and data libraries. These codes were originally developed many years ago and have undergone continual improvement. With a large initial effort and continued vigilance, the codes are easily portable from one type of hardware to another. The performance of scientific work-stations (SWS) has evolved to the point that such platforms can be used routinely to perform sophisticated radiation transport calculations. As the personal computer (PC) performance approaches that of the SWS, the hardware options for desk-top radiation transport calculations expands considerably. The current status of the radiation transport codes within the LARTCS is described: MCNP, SABRINA, LAHET, ONEDANT, TWODANT, TWOHEX, and ONELD. Specifically, the authors discuss hardware systems on which the codes run and present code performance comparisons for various machines

Graphical user interface for a robotic workstation in a surgical environment.

Science.gov (United States)

Bielski, A; Lohmann, C P; Maier, M; Zapp, D; Nasseri, M A

2016-08-01

Surgery using a robotic system has proven to have significant potential but is still a highly challenging task for the surgeon. An eye surgery assistant has been developed to eliminate the problem of tremor caused by human motions endangering the outcome of ophthalmic surgery. In order to exploit the full potential of the robot and improve the workflow of the surgeon, providing the ability to change control parameters live in the system as well as the ability to connect additional ancillary systems is necessary. Additionally the surgeon should always be able to get an overview over the status of all systems with a quick glance. Therefore a workstation has been built. The contribution of this paper is the design and the implementation of an intuitive graphical user interface for this workstation. The interface has been designed with feedback from surgeons and technical staff in order to ensure its usability in a surgical environment. Furthermore, the system was designed with the intent of supporting additional systems with minimal additional effort.

Image processing with personal computer

International Nuclear Information System (INIS)

Hara, Hiroshi; Handa, Madoka; Watanabe, Yoshihiko

1990-01-01

The method of automating the judgement works using photographs in radiation nondestructive inspection with a simple type image processor on the market was examined. The software for defect extraction and making binary and the software for automatic judgement were made for trial, and by using the various photographs on which the judgement was already done as the object, the accuracy and the problematic points were tested. According to the state of the objects to be photographed and the condition of inspection, the accuracy of judgement from 100% to 45% was obtained. The criteria for judgement were in conformity with the collection of reference photographs made by Japan Cast Steel Association. In the non-destructive inspection by radiography, the number and size of the defect images in photographs are visually judged, the results are collated with the standard, and the quality is decided. Recently, the technology of image processing with personal computers advanced, therefore by utilizing this technology, the automation of the judgement of photographs was attempted to improve the accuracy, to increase the inspection efficiency and to realize labor saving. (K.I.)

Functionalizing 2PP-fabricated microtools for optical manipulation on the BioPhotonics Workstation

DEFF Research Database (Denmark)

Matsuoka, Tomoyo; Nishi, Masayuki; Sakakura, Masaaki

Functionalization of the structures fabricated by two-photon polymerization was achieved by coating them with sol-gel materials, which contain calcium indicators. The structures are expected to work potentially as nano-sensors on the BioPhotonics Workstation....

Development of an EVA systems cost model. Volume 2: Shuttle orbiter crew and equipment translation concepts and EVA workstation concept development and integration

Science.gov (United States)

1975-01-01

EVA crewman/equipment translational concepts are developed for a shuttle orbiter payload application. Also considered are EVA workstation systems to meet orbiter and payload requirements for integration of workstations into candidate orbiter payload worksites.

A personal computer code for seismic evaluations of nuclear power plants facilities

International Nuclear Information System (INIS)

Xu, J.; Philippacopoulos, A.J.; Graves, H.

1990-01-01

The program CARES (Computer Analysis for Rapid Evaluation of Structures) is an integrated computational system being developed by Brookhaven National Laboratory (BNL) for the U.S. Nuclear Regulatory Commission. It is specifically designed to be a personal computer (PC) operated package which may be used to determine the validity and accuracy of analysis methodologies used for structural safety evaluations of nuclear power plants. CARES is structured in a modular format. Each module performs a specific type of analysis i.e., static or dynamic, linear or nonlinear, etc. This paper describes the various features which have been implemented into the Seismic Module of CARES

Embedding knowledge in a workstation

Energy Technology Data Exchange (ETDEWEB)

Barber, G

1982-01-01

This paper describes an approach to supporting work in the office. Using and extending ideas from the field of artificial intelligence (AI) it describes office work as a problem solving activity. A knowledge embedding language called OMEGA is used to embed knowledge of the organization into an office worker's workstation in order to support the office worker in his or her problem solving. A particular approach to reasoning about change and contradiction is discussed. This approach uses OMEGA's viewpoint mechanism. OMEGA's viewpoint mechanism is a general contradiction handling facility. Unlike other knowledge representation systems, when a contradiction is reached the reasons for the contradiction can be analyzed by the reduction mechanism without having to resort to a backtracking mechanism. The viewpoint mechanism is the heart of the problem solving support paradigm. This paradigm is an alternative to the classical view of problem solving in AI. Office workers are supported using the problem solving support paradigm. 16 references.

Evaluation plan for a cardiological multi-media workstation (I4C project)

NARCIS (Netherlands)

Hofstede, J.W. van der; Quak, A.B.; Ginneken, A.M. van; Macfarlane, P.W.; Watson, J.; Hendriks, P.R.; Zeelenberg, C.

1997-01-01

The goal of the I4C project (Integration and Communication for the Continuity of Cardiac Care) is to build a multi-media workstation for cardiac care and to assess its impact in the clinical setting. This paper describes the technical evaluation plan for the prototype.

Dissemination of Information in Developing Countries: The Personal Computer and beyond

Science.gov (United States)

Wong, Wai-Man

2005-01-01

With the blooming of information in digital format, dissemination of information is becoming a big challenge for developing countries. It is not only due to the limited provision of personal computers--in addition, the technological infrastructure and the ability to access information are also becoming major concerns in developing countries. This…

xdamp Version 4: An IDL Based Data and Image Manipulation Program

International Nuclear Information System (INIS)

William P. Ballard

2002-01-01

The original DAMP (W t a Manipulation Program) was written by Mark Hedemann of Sandia National Laboratories and used the CA-DISSPLA(trademark) (available from Computer Associates International, Inc., Garden City, NY) graphics package as its engine. It was used to plot, modify, and otherwise manipulate the one-dimensional data waveforms (data vs. time) from a wide variety of accelerators. With the waning of CA-DISSPLA and the increasing popularity of Unix(reg s ign)-based workstations, a replacement was needed. This package uses the IDL(reg s ign) software, available from Research Systems Incorporated, a Xerox company, in Boulder, Colorado, as the engine, and creates a set of widgets to manipulate the data in a manner similar to the original DAMP and earlier versions of xdamp. IDL is currently supported on a wide variety of Unix platforms such as IBM(reg s ign) workstations, Hewlett Packard workstations, SUN(reg s ign) workstations, Microsoft(reg s ign) Windows(trademark) computers, Macintosh(reg s ign) computers and Digital Equipment Corporation VMS(reg s ign) and Alpha(reg s ign) systems. Thus, xdamp is portable across many platforms. We have verified operation, albeit with some minor IDL bugs, on personal computers using Windows 95 and Windows NT; IBM Unix platforms; DEC Alpha and VMS systems; HP 9000/700 series workstations; and Macintosh computers, both regular and PowerPC(trademark) versions. Version 4 is an update that removes some obsolete features and better supports very large arrays and Excel formatted data import

Design considerations for a neuroradiologic picture archival and image processing workstation

International Nuclear Information System (INIS)

Fishbein, D.S.

1986-01-01

The design and implementation of a small scale image archival and processing workstation for use in the study of digitized neuroradiologic images is described. The system is designed to be easily interfaced to existing equipment (presently PET, NMR and CT), function independent of a central file server, and provide for a versatile image processing environment. (Auth.)

Hepatic volumetry with PhotoShop in personal computer.

Science.gov (United States)

Lu, Yi; Wu, Zheng; Liu, Chang; Wang, Hao-Hua

2004-02-01

Convenient way to clarify liver volume or tumor volume in the liver is eagerly demanded by hepatobiliary surgeons, for so many aspects of clinical work need to know the liver volumetry. At present, some methods have been used to measure the liver volumetry, such as computed tomography (CT) scans, three-dimensional ultrasound volumetric system([1]) and 3-dimensional sonography([2,3]) et al. But enough volumetric information was failed to obtain by surgeons and a new way of measuring the liver volumetry that can be operated by themselves is exigent. Whereas we devise a new method of using PhotoShop in personal computer to measure the liver volumetry. A piece of whole CT film was transformed to a high quality digitized image by digital camera or scanner and then the digitized image was conducted as JPEG file into personal computer. The JPEG image file of CT film was opened by PhotoShop. Determining the edge of interested areas, and the data of pixel values of the interested areas divided by 1 cm2 pixel value will produce the actual area with the unit of square centimeter. If section thickness of CT scan is 1 cm, the sum of the areas of the liver or tumor in all sections naturally is the volume of the liver or tumor. Comparison of 10 hepatic volumes gained by this method and those gained by the GE Prospeed CT set showed a good relativity between the two groups. The volumes of three right lobes were calculated by this method before lobectomy and their real volumes were obtained postoperatively by a volumenometer. Their variation was limited to 5%. Hepatic volume obtained by PhotoShop is reliable. This method can be used to measure hepatic volume perfectly to meet clinical demand, and many parameters such as liver resection rate, graft volume can be achieved. The disadvantage of this method is the step of copying the pixel value from PhotoShop to Microsoft Excel.

Personal Computer-less (PC-less) Microcontroller Training Kit

Science.gov (United States)

Somantri, Y.; Wahyudin, D.; Fushilat, I.

2018-02-01

The need of microcontroller training kit is necessary for practical work of students of electrical engineering education. However, to use available training kit not only costly but also does not meet the need of laboratory requirements. An affordable and portable microcontroller kit could answer such problem. This paper explains the design and development of Personal Computer Less (PC-Less) Microcontroller Training Kit. It was developed based on Lattepanda processor and Arduino microcontroller as target. The training kit equipped with advanced input-output interfaces that adopted the concept of low cost and low power system. The preliminary usability testing proved this device can be used as a tool for microcontroller programming and industrial automation training. By adopting the concept of portability, the device could be operated in the rural area which electricity and computer infrastructure are limited. Furthermore, the training kit is suitable for student of electrical engineering student from university and vocational high school.

xdamp Version 6 : an IDL-based data and image manipulation program.

Energy Technology Data Exchange (ETDEWEB)

Ballard, William Parker

2012-04-01

The original DAMP (DAta Manipulation Program) was written by Mark Hedemann of Sandia National Laboratories and used the CA-DISSPLA{trademark} (available from Computer Associates International, Inc., Garden City, NY) graphics package as its engine. It was used to plot, modify, and otherwise manipulate the one-dimensional data waveforms (data vs. time) from a wide variety of accelerators. With the waning of CA-DISSPLA and the increasing popularity of Unix(reg sign)-based workstations, a replacement was needed. This package uses the IDL(reg sign) software, available from Research Systems Incorporated, a Xerox company, in Boulder, Colorado, as the engine, and creates a set of widgets to manipulate the data in a manner similar to the original DAMP and earlier versions of xdamp. IDL is currently supported on a wide variety of Unix platforms such as IBM(reg sign) workstations, Hewlett Packard workstations, SUN(reg sign) workstations, Microsoft(reg sign) Windows{trademark} computers, Macintosh(reg sign) computers and Digital Equipment Corporation VMS(reg sign) and Alpha(reg sign) systems. Thus, xdamp is portable across many platforms. We have verified operation, albeit with some minor IDL bugs, on personal computers using Windows 7 and Windows Vista; Unix platforms; and Macintosh computers. Version 6 is an update that uses the IDL Virtual Machine to resolve the need for licensing IDL.

xdamp Version 6.100: An IDL(reg sign)-based data and image manipulation program

International Nuclear Information System (INIS)

Ballard, William Parker

2012-01-01

The original DAMP (DAta Manipulation Program) was written by Mark Hedemann of Sandia National Laboratories and used the CA-DISSPLA(trademark) (available from Computer Associates International, Inc., Garden City, NY) graphics package as its engine. It was used to plot, modify, and otherwise manipulate the one-dimensional data waveforms (data vs. time) from a wide variety of accelerators. With the waning of CA-DISSPLA and the increasing popularity of Unix(reg sign)-based workstations, a replacement was needed. This package uses the IDL(reg sign) software, available from Research Systems Incorporated, a Xerox company, in Boulder, Colorado, as the engine, and creates a set of widgets to manipulate the data in a manner similar to the original DAMP and earlier versions of xdamp. IDL is currently supported on a wide variety of Unix platforms such as IBM(reg sign) workstations, Hewlett Packard workstations, SUN(reg sign) workstations, Microsoft(reg sign) Windows(trademark) computers, Macintosh(reg sign) computers and Digital Equipment Corporation VMS(reg sign) and Alpha(reg sign) systems. Thus, xdamp is portable across many platforms. We have verified operation, albeit with some minor IDL bugs, on personal computers using Windows 7 and Windows Vista; Unix platforms; and Macintosh computers. Version 6 is an update that uses the IDL Virtual Machine to resolve the need for licensing IDL.

Effect of immediate feedback training on observer performance on a digital radiology workstation

International Nuclear Information System (INIS)

Mc Neill, K.M.; Maloney, K.; Elam, E.A.; Hillman, B.J.; Witzke, D.B.

1990-01-01

This paper reports on testing the hypothesis that training radiologists on a digital workstation would affect their efficiency and subjective acceptance of radiologic interpretation based on images shown on a cathode ray tub (CRT). Using a digital radiology workstation, six faculty radiologists and four senior residents read seven groups of six images each. In each group, three images were ranked as easy and three were ranked as difficult. All images were abnormal posteroanterior chest radiographs. On display of each image, the observer was asked which findings were present. After the observer listed his or her findings, the experimenter listed any findings not mentioned and pointed out any incorrect findings. The time to finding was recorded for each image, along with the number of corrections and missed findings. A postexperiment questionnaire was given to obtain subjective responses from the observers

Robotic, MEMS-based Multi Utility Sample Preparation Instrument for ISS Biological Workstation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This project will develop a multi-functional, automated sample preparation instrument for biological wet-lab workstations on the ISS. The instrument is based on a...

Gamma spectrometric system based on the personal computer Pravetz-83

International Nuclear Information System (INIS)

Yanakiev, K; Grigorov, T.; Vuchkov, M.

1985-01-01

A gamma spectrometric system based on a personal microcomputer Pravets-85 is described. The analog modules are NIM standard. ADC data are stored in the memory of the computer via a DMA channel and a real-time data processing is possible. The results from a series of tests indicate that the performance of the system is comparable with that of comercially avalable computerized spectrometers Ortec and Canberra

Networking issues---Lan and Wan needs---The impact of workstations

International Nuclear Information System (INIS)

Harvey, J.

1990-01-01

This review focuses on the use of networks in the LEP experiments at CERN. The role of the extended LAN at CERN is discussed in some detail, with particular emphasis on the impact the sudden growth in the use of workstations is having. The problem of network congestion is highlighted and possible evolution to FDDI mentioned. The status and use of the wide area connections are also reported

Achieving high performance in numerical computations on RISC workstations and parallel systems

Energy Technology Data Exchange (ETDEWEB)

Goedecker, S. [Max-Planck Inst. for Solid State Research, Stuttgart (Germany); Hoisie, A. [Los Alamos National Lab., NM (United States)

1997-08-20

The nominal peak speeds of both serial and parallel computers is raising rapidly. At the same time however it is becoming increasingly difficult to get out a significant fraction of this high peak speed from modern computer architectures. In this tutorial the authors give the scientists and engineers involved in numerically demanding calculations and simulations the necessary basic knowledge to write reasonably efficient programs. The basic principles are rather simple and the possible rewards large. Writing a program by taking into account optimization techniques related to the computer architecture can significantly speedup your program, often by factors of 10--100. As such, optimizing a program can for instance be a much better solution than buying a faster computer. If a few basic optimization principles are applied during program development, the additional time needed for obtaining an efficient program is practically negligible. In-depth optimization is usually only needed for a few subroutines or kernels and the effort involved is therefore also acceptable.

[Personal computer-based computer monitoring system of the anesthesiologist (2-year experience in development and use)].

Science.gov (United States)

Buniatian, A A; Sablin, I N; Flerov, E V; Mierbekov, E M; Broĭtman, O G; Shevchenko, V V; Shitikov, I I

1995-01-01

Creation of computer monitoring systems (CMS) for operating rooms is one of the most important spheres of personal computer employment in anesthesiology. The authors developed a PC RS/AT-based CMS and effectively used it for more than 2 years. This system permits comprehensive monitoring in cardiosurgical operations by real time processing the values of arterial and central venous pressure, pressure in the pulmonary artery, bioelectrical activity of the brain, and two temperature values. Use of this CMS helped appreciably improve patients' safety during surgery. The possibility to assess brain function by computer monitoring the EEF simultaneously with central hemodynamics and body temperature permit the anesthesiologist to objectively assess the depth of anesthesia and to diagnose cerebral hypoxia. Automated anesthesiological chart issued by the CMS after surgery reliably reflects the patient's status and the measures taken by the anesthesiologist.

Factors leading to the computer vision syndrome: an issue at the contemporary workplace.

Science.gov (United States)

Izquierdo, Juan C; García, Maribel; Buxó, Carmen; Izquierdo, Natalio J

2007-01-01

Vision and eye related problems are common among computer users, and have been collectively called the Computer Vision Syndrome (CVS). An observational study in order to identify the risk factors leading to the CVS was done. Twenty-eight participants answered a validated questionnaire, and had their workstations examined. The questionnaire evaluated personal, environmental, ergonomic factors, and physiologic response of computer users. The distance from the eye to the computers' monitor (A), the computers' monitor height (B), and visual axis height (C) were measured. The difference between B and C was calculated and labeled as D. Angles of gaze to the computer monitor were calculated using the formula: angle=tan-1(D/A). Angles were divided into two groups: participants with angles of gaze ranging from 0 degree to 13.9 degrees were included in Group 1; and participants gazing at angles larger than 14 degrees were included in Group 2. Statistical analysis of the evaluated variables was made. Computer users in both groups used more tear supplements (as part of the syndrome) than expected. This association was statistically significant (p syndrome is the angle of gaze at the computer monitor. Pain in computer users is diminished when gazing downwards at angles of 14 degrees or more. The CVS remains an under estimated and poorly understood issue at the workplace. The general public, health professionals, the government, and private industries need to be educated about the CVS.

Inducing and measuring emotion through a multiplayer first-person shooter computer game

NARCIS (Netherlands)

Merkx, P.A.B.; Truong, K.P.; Neerincx, M.A.

2007-01-01

To develop an annotated database of spontaneous, multimodal, emotional expressions, recordings were made of facial and vocal expressions of emotions while participants were playing a multiplayer first-person shooter (fps) computer game. During a replay of the session, participants scored their own

Development of a computer model for polycrystalline thin-film CuInSe sub 2 and CdTe solar cells

Energy Technology Data Exchange (ETDEWEB)

Gray, J.L.; Schwartz, R.J.; Lee, Y.J. (Purdue Univ., Lafayette, IN (United States))

1992-09-01

This report describes work to develop an accurate numerical model for CuInSe{sub 2} (CIS) and CdTe-based solar cells capable of running on a personal computer. Such a model will aid researchers in designing and analyzing CIS- and CdTe-based solar cells. ADEPT (A Device Emulation Pregrain and Tool) was used as the basis for this model. An additional objective of this research was to use the models developed to analyze the performance of existing and proposed CIS- and CdTe-based solar cells. The development of accurate numerical models for CIS- and CdTe-based solar cells required the compilation of cell performance data (for use in model verification) and the compilation of measurements of material parameters. The development of the numerical models involved implementing the various physical models appropriate to CIS and CdTe, as well as some common window. A version of the model capable of running on an IBM-comparable personal computer was developed (primary code development is on a SUN workstation). A user-friendly interface with pop-up menus is continuing to be developed for release with the IBM-compatible model.

An application for multi-person task synchronization

Science.gov (United States)

Brown, Robert L.; Doyle, Dee

1990-01-01

Computer applications are studied that will enable a group of people to synchronize their actions when following a predefined task sequence. It is assumed that the people involved only have computer workstations available to them for communication. Hence, the approach is to study how the computer can be used to help a group remain synchronized. A series of applications were designed and developed that can be used as vehicles for experimentation. An example of how this technique can be used for a remote coaching capability is explained in a report describing an experiment that simulated a Life Sciences experiment on-board Space Station Freedom, with a ground based principal investigator providing the expertise by coaching the on-orbit mission specialist.

Multi channel analyzer system addible to personal computer

International Nuclear Information System (INIS)

Ramirez J, F.J.; Garcia R, R.; Ramirez N, R.; Torres B, M.A.

1996-01-01

It has been developed a Multichannel analyzer system which was added to personal computer of 4096 channels for its use, in nuclear radiations matters, such as X-ray fluorescence analysis, Neutron activation analysis, etc. in that is interesting to know the radiation energy distribution. This system has three modules; a Digital analogical converter of 12 bits, fast (total conversion time of 6 μ s) that use a successive approximation technique with linearity correction by the gliding rule method. A digital card with microprocessor that is useful as an interface with the computer for the acquisition, data storage and the process control. A computer program with extensive use of graphics, friendly with the user in order to facilitate its utilization, also with the option to find peaks, an expansion of an interesting area, information storage in compatible format with spectra analysis programs, etc. Twenty five units of this system have been constructed which all of they were distributed to the ARCAL Member countries and the other 10 units were distributed in the National Institute of Nuclear Research. On the other hand, it has been able to find other applications where the information can be converted to pulses and the interest variable is represented by the pulse amplitude. (Author)

Leveraging Social Computing for Personalized Crisis Communication using Social Media

Science.gov (United States)

Leykin, Dmitry; Aharonson-Daniel, Limor; Lahad, Mooli

2016-01-01

Introduction: The extensive use of social media in modern life redefines social interaction and communication. Communication plays an important role in mitigating, or exacerbating, the psychological and behavioral responses to critical incidents and disasters. As recent disasters demonstrated, people tend to converge to social media during and following emergencies. Authorities can then use this media and other computational methods to gain insights from the public, mainly to enhance situational awareness, but also to improve their communication with the public and public adherence to instructions. Methods: The current review presents a conceptual framework for studying psychological aspects of crisis and risk communication using the social media through social computing. Results: Advanced analytical tools can be integrated in the processes and objectives of crisis communication. The availability of the computational techniques can improve communication with the public by a process of Hyper-Targeted Crisis Communication. Discussion: The review suggests that using advanced computational tools for target-audience profiling and linguistic matching in social media, can facilitate more sensitive and personalized emergency communication. PMID:27092290

Leveraging Social Computing for Personalized Crisis Communication using Social Media.

Science.gov (United States)

Leykin, Dmitry; Aharonson-Daniel, Limor; Lahad, Mooli

2016-03-24

The extensive use of social media in modern life redefines social interaction and communication. Communication plays an important role in mitigating, or exacerbating, the psychological and behavioral responses to critical incidents and disasters. As recent disasters demonstrated, people tend to converge to social media during and following emergencies. Authorities can then use this media and other computational methods to gain insights from the public, mainly to enhance situational awareness, but also to improve their communication with the public and public adherence to instructions. The current review presents a conceptual framework for studying psychological aspects of crisis and risk communication using the social media through social computing. Advanced analytical tools can be integrated in the processes and objectives of crisis communication. The availability of the computational techniques can improve communication with the public by a process of Hyper-Targeted Crisis Communication. The review suggests that using advanced computational tools for target-audience profiling and linguistic matching in social media, can facilitate more sensitive and personalized emergency communication.

CD-based image archival and management on a hybrid radiology intranet.

Science.gov (United States)

Cox, R D; Henri, C J; Bret, P M

1997-08-01

This article describes the design and implementation of a low-cost image archival and management solution on a radiology network consisting of UNIX, IBM personal computer-compatible (IBM, Purchase, NY) and Macintosh (Apple Computer, Cupertino, CA) workstations. The picture archiving and communications system (PACS) is modular, scaleable and conforms to the Digital Imaging and Communications in Medicine (DICOM) 3.0 standard for image transfer, storage and retrieval. Image data is made available on soft-copy reporting workstations by a work-flow management scheme and on desktop computers through a World Wide Web (WWW) interface. Data archival is based on recordable compact disc (CD) technology and is automated. The project has allowed the radiology department to eliminate the use of film in magnetic resonance (MR) imaging, computed tomography (CT) and ultrasonography.

A Context-Aware Ubiquitous Learning Approach for Providing Instant Learning Support in Personal Computer Assembly Activities

Science.gov (United States)

Hsu, Ching-Kun; Hwang, Gwo-Jen

2014-01-01

Personal computer assembly courses have been recognized as being essential in helping students understand computer structure as well as the functionality of each computer component. In this study, a context-aware ubiquitous learning approach is proposed for providing instant assistance to individual students in the learning activity of a…

Biomek Cell Workstation: A Variable System for Automated Cell Cultivation.

Science.gov (United States)

Lehmann, R; Severitt, J C; Roddelkopf, T; Junginger, S; Thurow, K

2016-06-01

Automated cell cultivation is an important tool for simplifying routine laboratory work. Automated methods are independent of skill levels and daily constitution of laboratory staff in combination with a constant quality and performance of the methods. The Biomek Cell Workstation was configured as a flexible and compatible system. The modified Biomek Cell Workstation enables the cultivation of adherent and suspension cells. Until now, no commercially available systems enabled the automated handling of both types of cells in one system. In particular, the automated cultivation of suspension cells in this form has not been published. The cell counts and viabilities were nonsignificantly decreased for cells cultivated in AutoFlasks in automated handling. The proliferation of manual and automated bioscreening by the WST-1 assay showed a nonsignificant lower proliferation of automatically disseminated cells associated with a mostly lower standard error. The disseminated suspension cell lines showed different pronounced proliferations in descending order, starting with Jurkat cells followed by SEM, Molt4, and RS4 cells having the lowest proliferation. In this respect, we successfully disseminated and screened suspension cells in an automated way. The automated cultivation and dissemination of a variety of suspension cells can replace the manual method. © 2015 Society for Laboratory Automation and Screening.

Application of a personal computer in a high energy physics experiment

International Nuclear Information System (INIS)

Petta, P.

1987-04-01

UA1 is a detector block at the CERN Super Synchrotron Collider, MacVEE is Micro computer applied to the Control of VME Electronic Equipment, a software development system for the data readout system and for the implementation of the user interface of the experiment control. A commercial personal computer is used. Examples of applications are the Data Acquisition Console, the Scanner Desc equipment and the AMERICA Ram Disks codes. Further topics are the MacUA1 development system for M68K-VME codes and an outline of the future MacVEE System Supervisor. 23 refs., 10 figs., 3 tabs. (qui)

Performance of Personal Workspace Controls Final Report

Energy Technology Data Exchange (ETDEWEB)

Rubinstein, Francis; Kiliccote, Sila; Loffeld, John; Pettler,Pete; Snook, Joel

2004-12-01

One of the key deliverables for the DOE-funded controls research at LBNL for FY04 was the development of a prototype Personal Workspace Control system. The successful development of this system is a critical milestone for the LBNL Lighting Controls Research effort because this system demonstrates how IBECS can add value to today's Task Ambient lighting systems. LBNL has argued that by providing both the occupant and the facilities manager with the ability to precisely control the operation of overhead lighting and all task lighting in a coordinated manner, that task ambient lighting can optimize energy performance and occupant comfort simultaneously [Reference Task Ambient Foundation Document]. The Personal Workspace Control system is the application of IBECS to this important lighting problem. This report discusses the development of the Personal Workspace Control to date including descriptions of the different fixture types that have been converted to IBECS operation and a detailed description of the operation of PWC Scene Controller, which provides the end user with precise control of his task ambient lighting system. The objective, from the Annual Plan, is to demonstrate improvements in efficiency, lighting quality and occupant comfort realized using Personal Workspace Controls (PWC) designed to optimize the delivery of lighting to the individual's workstation regardless of which task-ambient lighting solution is chosen. The PWC will be capable of controlling floor-mounted, desk lamps, furniture-mounted and overhead lighting fixtures from a personal computer and handheld remote. The PWC will use an environmental sensor to automatically monitor illuminance, temperature and occupancy and to appropriately modulate ambient lighting according to daylight availability and to switch off task lighting according to local occupancy. [Adding occupancy control to the system would blunt the historical criticism of occupant-controlled lighting - the tendency of the

Advanced computers and simulation