Comparison Between 2D and 3D Simulations of Rate Dependent Friction Using DEM

Science.gov (United States)

Wang, C.; Elsworth, D.

2017-12-01

Rate-state dependent constitutive laws of frictional evolution have been successful in representing many of the first- and second- order components of earthquake rupture. Although this constitutive law has been successfully applied in numerical models, difficulty remains in efficient implementation of this constitutive law in computationally-expensive granular mechanics simulations using discrete element methods (DEM). This study introduces a novel approach in implementing a rate-dependent constitutive relation of contact friction into DEM. This is essentially an implementation of a slip-weakening constitutive law onto local particle contacts without sacrificing computational efficiency. This implementation allows the analysis of slip stability of simulated fault gouge materials. Velocity-stepping experiments are reported on both uniform and textured distributions of quartz and talc as 3D analogs of gouge mixtures. Distinct local slip stability parameters (a-b) are assigned to the quartz and talc, respectively. We separately vary talc content from 0 to 100% in the uniform mixtures and talc layer thickness from 1 to 20 particles in the textured mixtures. Applied shear displacements are cycled through velocities of 1μm/s and 10μm/s. Frictional evolution data are collected and compared to 2D simulation results. We show that dimensionality significantly impacts the evolution of friction. 3D simulation results are more representative of laboratory observed behavior and numerical noise is shown at a magnitude of 0.01 in terms of friction coefficient. Stability parameters (a-b) can be straightforwardly obtained from analyzing velocity steps, and are different from locally assigned (a-b) values. Sensitivity studies on normal stress, shear velocity, particle size, local (a-b) values, and characteristic slip distance (Dc) show that the implementation is sensitive to local (a-b) values and relations between (Dc) and particle size.

Study of the adaptive refinement on an open source 2D shallow-water flow solver using quadtree grid for flash flood simulations.

Science.gov (United States)

Kirstetter, G.; Popinet, S.; Fullana, J. M.; Lagrée, P. Y.; Josserand, C.

2015-12-01

The full resolution of shallow-water equations for modeling flash floods may have a high computational cost, so that majority of flood simulation softwares used for flood forecasting uses a simplification of this model : 1D approximations, diffusive or kinematic wave approximations or exotic models using non-physical free parameters. These kind of approximations permit to save a lot of computational time by sacrificing in an unquantified way the precision of simulations. To reduce drastically the cost of such 2D simulations by quantifying the lost of precision, we propose a 2D shallow-water flow solver built with the open source code Basilisk1, which is using adaptive refinement on a quadtree grid. This solver uses a well-balanced central-upwind scheme, which is at second order in time and space, and treats the friction and rain terms implicitly in finite volume approach. We demonstrate the validity of our simulation on the case of the flood of Tewkesbury (UK) occurred in July 2007, as shown on Fig. 1. On this case, a systematic study of the impact of the chosen criterium for adaptive refinement is performed. The criterium which has the best computational time / precision ratio is proposed. Finally, we present the power law giving the computational time in respect to the maximum resolution and we show that this law for our 2D simulation is close to the one of 1D simulation, thanks to the fractal dimension of the topography. [1] http://basilisk.fr/

Watershed-based point sources permitting strategy and dynamic permit-trading analysis.

Science.gov (United States)

Ning, Shu-Kuang; Chang, Ni-Bin

2007-09-01

Permit-trading policy in a total maximum daily load (TMDL) program may provide an additional avenue to produce environmental benefit, which closely approximates what would be achieved through a command and control approach, with relatively lower costs. One of the important considerations that might affect the effective trading mechanism is to determine the dynamic transaction prices and trading ratios in response to seasonal changes of assimilative capacity in the river. Advanced studies associated with multi-temporal spatially varied trading ratios among point sources to manage water pollution hold considerable potential for industries and policy makers alike. This paper aims to present an integrated simulation and optimization analysis for generating spatially varied trading ratios and evaluating seasonal transaction prices accordingly. It is designed to configure a permit-trading structure basin-wide and provide decision makers with a wealth of cost-effective, technology-oriented, risk-informed, and community-based management strategies. The case study, seamlessly integrating a QUAL2E simulation model with an optimal waste load allocation (WLA) scheme in a designated TMDL study area, helps understand the complexity of varying environmental resources values over space and time. The pollutants of concern in this region, which are eligible for trading, mainly include both biochemical oxygen demand (BOD) and ammonia-nitrogen (NH3-N). The problem solution, as a consequence, suggests an array of waste load reduction targets in a well-defined WLA scheme and exhibits a dynamic permit-trading framework among different sub-watersheds in the study area. Research findings gained in this paper may extend to any transferable dynamic-discharge permit (TDDP) program worldwide.

An economic analysis of tradeable emission permits for sulphur dioxide emissions in Europe

International Nuclear Information System (INIS)

Kruitwagen, S.

1996-01-01

The central theme of this thesis is the analysis of the applicability of tradeable emission permits for cost-effective SO2 reduction in Europe. First, an economic theoretical background is presented based on a literature study. Second, integrated assessment models are presented and compared. One of these models is selected for simulation. Third, a new permit trading systems is developed and analysed by detailed simulations of trading schemes, including their economic and environmental implications. Chapter 2 discusses some general economic aspects of pollution control. Attention is paid to the cost effectiveness of pollution control, to the international dimension of acid rain policy and to the need for cooperation. Some general game theoretic concepts are reviewed. Also attention is paid to the alternative policy instruments for emission control, focusing on tradeable emission permits. The theory of tradeable emission permits is elaborated in Chapter 3. Permit trading for pollutants that are non-uniformly mixing is thoroughly discussed and illustrated by some empirical studies. After discussing both emission permit and deposition permit trading systems, alternative systems of tradeable permits for this kind of pollutants are examined. Two main aspects in examining permit trading systems concern (1) the kind of trading process assumed, involving the distinction between simultaneous multilateral permit trading versus bilateral sequential permit trading, and (2) the initial distribution of emission permits. The thorough discussion on tradeable permits contributes to a better understanding of this policy instrument and sheds light on the implications of permit trading for non-uniformly mixing pollutants. The findings of this chapter indicate that a new permit trading system has to be developed. Chapter 4 describes and compares integrated assessment models for simulation of acid rain control. First, three integrated assessment models for the European acid rain problem

Assessing the impact of aerosol-atmosphere interactions in convection-permitting regional climate simulations: the Rolf medicane in 2011

Science.gov (United States)

José Gómez-Navarro, Juan; María López-Romero, José; Palacios-Peña, Laura; Montávez, Juan Pedro; Jiménez-Guerrero, Pedro

2017-04-01

A critical challenge for assessing regional climate change projections relies on improving the estimate of atmospheric aerosol impact on clouds and reducing the uncertainty associated with the use of parameterizations. In this sense, the horizontal grid spacing implemented in state-of-the-art regional climate simulations is typically 10-25 kilometers, meaning that very important processes such as convective precipitation are smaller than a grid box, and therefore need to be parameterized. This causes large uncertainties, as closure assumptions and a number of parameters have to be established by model tuning. Convection is a physical process that may be strongly conditioned by atmospheric aerosols, although the solution of aerosol-cloud interactions in warm convective clouds remains nowadays a very important scientific challenge, rendering parametrization of these complex processes an important bottleneck that is responsible from a great part of the uncertainty in current climate change projections. Therefore, the explicit simulation of convective processes might improve the quality and reliability of the simulations of the aerosol-cloud interactions in a wide range of atmospheric phenomena. Particularly over the Mediterranean, the role of aerosol particles is very important, being this a crossroad that fuels the mixing of particles from different sources (sea-salt, biomass burning, anthropogenic, Saharan dust, etc). Still, the role of aerosols in extreme events in this area such as medicanes has been barely addressed. This work aims at assessing the role of aerosol-atmosphere interaction in medicanes with the help of the regional chemistry/climate on-line coupled model WRF-CHEM run at a convection-permitting resolution. The analysis is exemplary based on the "Rolf" medicane (6-8 November 2011). Using this case study as reference, four sets of simulations are run with two spatial resolutions: one at a convection-permitting configuration of 4 km, and other at the

20th Joint Workshop on Sustained Simulation Performance

CERN Document Server

Bez, Wolfgang; Focht, Erich; Patel, Nisarg; Kobayashi, Hiroaki

2016-01-01

The book presents the state of the art in high-performance computing and simulation on modern supercomputer architectures. It explores general trends in hardware and software development, and then focuses specifically on the future of high-performance systems and heterogeneous architectures. It also covers applications such as computational fluid dynamics, material science, medical applications and climate research and discusses innovative fields like coupled multi-physics or multi-scale simulations. The papers included were selected from the presentations given at the 20th Workshop on Sustained Simulation Performance at the HLRS, University of Stuttgart, Germany in December 2015, and the subsequent Workshop on Sustained Simulation Performance at Tohoku University in February 2016.

Progress towards 3D black hole merger simulations

International Nuclear Information System (INIS)

Seidel, E.

2001-01-01

I review recent progress in 3D numerical relativity, focused on simulations involving black holes evolved with singularity avoiding slicings, but also touching on recent results in advanced techniques like black hole excision. After a long series of axisymmetric and perturbative studies of distorted black holes and black hole collisions, similar studies were carried out with full 3D codes. The results showed that such black hole simulations can be carried out extremely accurately, although instabilities plague the simulation at uncomfortably early times. However, new formulations of Einstein's equations allow much more stable 3D evolutions than ever before, enabling the first studies of 3D gravitational collapse to a black hole. With these new formulations, for example, it has been possible to perform the first detailed simulations of 3D grazing collisions of black holes with unequal mass, spin, and with orbital angular momentum. I discuss the 3D black hole physics that can now be studied, and prospects for the future, which look increasingly bright due to recent progress in formulations, black hole excision, new gauge conditions, and larger computers. Simulations may soon be able to provide information about the final plunge of two black holes, of relevance for gravitational wave astronomy. (author)

27 CFR 20.44 - Disapproval of application.

Science.gov (United States)

2010-04-01

... and Users Application for Permit, Form 5150.22 § 20.44 Disapproval of application. The appropriate TTB..., a partner) is, by reason of their business experience, financial standing, or trade connections, not... statement as to any material fact, in connection with the application; or (d) The premises at which the...

40 CFR 71.6 - Permit content.

Science.gov (United States)

2010-07-01

... § 71.5(d). (B) Prompt reporting of deviations from permit requirements, including those attributable to... prompt or otherwise specifies a time frame for reporting deviations, that definition or time frame shall... and air pollution control equipment), practices, or operations regulated or required under the permit...

D1+ Simulator: A cost and risk optimized approach to nuclear power plant simulator modernization

International Nuclear Information System (INIS)

Wischert, W.

2006-01-01

D1-Simulator is operated by Kraftwerks-Simulator-Gesellschaft (KSG) and Gesellschaft f?r Simulatorschulung (GfS) at the Simulator Centre in Essen since 1977. The full-scope control room training simulator, used for Kernkraftwerk Biblis (KWB) is based on a PDP-11 hardware platform and is mainly programmed in ASSEMBLER language. The Simulator has reached a continuous high availability of operation throughout the years due to specialized hardware and software support from KSG maintenance team. Nevertheless, D1-Simulator largely reveals limitations with respect to computer capacity and spares and suffers progressively from the non-availability of hardware replacement materials. In order to ensure long term maintainability within the framework of the consensus on nuclear energy, a 2-years refurbishing program has been launched by KWB focusing on quality and budgetary aspects. The so-called D1+ Simulator project is based on the re-use of validated data from existing simulators. Allowing for flexible project management methods, the project outlines a cost and risk optimized approach to Nuclear Power Plant (NPP) Simulator modernization. D1+ Simulator is being built by KSG/GfS in close collaboration with KWB and the simulator vendor THALES by re-using a modern hardware and software development environment from D56-Simulator, used by Kernkraftwerk Obrigheim (KWO) before its decommissioning in 2005. The Simulator project, launched in 2004, is expected to be completed by end of 2006. (author)

2-d Simulations of Test Methods

DEFF Research Database (Denmark)

Thrane, Lars Nyholm

2004-01-01

One of the main obstacles for the further development of self-compacting concrete is to relate the fresh concrete properties to the form filling ability. Therefore, simulation of the form filling ability will provide a powerful tool in obtaining this goal. In this paper, a continuum mechanical...... approach is presented by showing initial results from 2-d simulations of the empirical test methods slump flow and L-box. This method assumes a homogeneous material, which is expected to correspond to particle suspensions e.g. concrete, when it remains stable. The simulations have been carried out when...... using both a Newton and Bingham model for characterisation of the rheological properties of the concrete. From the results, it is expected that both the slump flow and L-box can be simulated quite accurately when the model is extended to 3-d and the concrete is characterised according to the Bingham...

Exact deconstruction of the 6D (2,0) theory

Science.gov (United States)

Hayling, J.; Papageorgakis, C.; Pomoni, E.; Rodríguez-Gómez, D.

2017-06-01

The dimensional-deconstruction prescription of Arkani-Hamed, Cohen, Kaplan, Karch and Motl provides a mechanism for recovering the A-type (2,0) theories on T 2, starting from a four-dimensional N=2 circular-quiver theory. We put this conjecture to the test using two exact-counting arguments: in the decompactification limit, we compare the Higgs-branch Hilbert series of the 4D N=2 quiver to the "half-BPS" limit of the (2,0) superconformal index. We also compare the full partition function for the 4D quiver on S 4 to the (2,0) partition function on S 4 × T 2. In both cases we find exact agreement. The partition function calculation sets up a dictionary between exact results in 4D and 6D.

Exact deconstruction of the 6D (2,0) theory

International Nuclear Information System (INIS)

Hayling, J.; Papageorgakis, C.; Pomoni, E.; Rodriguez-Gomez, D.

2017-06-01

The dimensional-deconstruction prescription of Arkani-Hamed, Cohen, Kaplan, Karch and Motl provides a mechanism for recovering the A-type (2,0) theories on T 2 , starting from a four-dimensional N=2 circular-quiver theory. We put this conjecture to the test using two exact-counting arguments: In the decompactification limit, we compare the Higgs-branch Hilbert series of the 4D N=2 quiver to the ''half-BPS'' limit of the (2,0) superconformal index. We also compare the full partition function for the 4D quiver on S 4 to the (2,0) partition function on S 4 x T 2 . In both cases we find exact agreement. The partition function calculation sets up a dictionary between exact results in 4D and 6D.

Numerical simulation of Ge solar cells using D-AMPS-1D code

Energy Technology Data Exchange (ETDEWEB)

Barrera, Marcela, E-mail: barrera@tandar.cnea.gov.ar [Comision Nacional de Energia Atomica, Avenida General Paz 1499, San Martin 1650, Buenos Aires (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina); Rubinelli, Francisco [Instituto de Desarrollo Tecnologico para la Industria Quimica (INTEC)-CONICET, Gueemes 3450, Santa Fe 3000 (Argentina); Rey-Stolle, Ignacio [Instituto de Energia Solar, Universidad Politecnica de Madrid, Avenida Complutense 30, Madrid 28040 (Spain); Pla, Juan [Comision Nacional de Energia Atomica, Avenida General Paz 1499, San Martin 1650, Buenos Aires (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina)

2012-08-15

A solar cell is a solid state device that converts the energy of sunlight directly into electricity by the photovoltaic effect. When light with photon energies greater than the band gap is absorbed by a semiconductor material, free electrons and free holes are generated by optical excitation in the material. The main characteristic of a photovoltaic device is the presence of internal electric field able to separate the free electrons and holes so they can pass out of the material to the external circuit before they recombine. Numerical simulation of photovoltaic devices plays a crucial role in their design, performance prediction, and comprehension of the fundamental phenomena ruling their operation. The electrical transport and the optical behavior of the solar cells discussed in this work were studied with the simulation code D-AMPS-1D. This software is an updated version of the one-dimensional (1D) simulation program Analysis of Microelectronic and Photonic Devices (AMPS) that was initially developed at The Penn State University, USA. Structures such as homojunctions, heterojunctions, multijunctions, etc., resulting from stacking layers of different materials can be studied by appropriately selecting characteristic parameters. In this work, examples of cells simulation made with D-AMPS-1D are shown. Particularly, results of Ge photovoltaic devices are presented. The role of the InGaP buffer on the device was studied. Moreover, a comparison of the simulated electrical parameters with experimental results was performed.

Numerical simulation of Ge solar cells using D-AMPS-1D code

International Nuclear Information System (INIS)

Barrera, Marcela; Rubinelli, Francisco; Rey-Stolle, Ignacio; Plá, Juan

2012-01-01

A solar cell is a solid state device that converts the energy of sunlight directly into electricity by the photovoltaic effect. When light with photon energies greater than the band gap is absorbed by a semiconductor material, free electrons and free holes are generated by optical excitation in the material. The main characteristic of a photovoltaic device is the presence of internal electric field able to separate the free electrons and holes so they can pass out of the material to the external circuit before they recombine. Numerical simulation of photovoltaic devices plays a crucial role in their design, performance prediction, and comprehension of the fundamental phenomena ruling their operation. The electrical transport and the optical behavior of the solar cells discussed in this work were studied with the simulation code D-AMPS-1D. This software is an updated version of the one-dimensional (1D) simulation program Analysis of Microelectronic and Photonic Devices (AMPS) that was initially developed at The Penn State University, USA. Structures such as homojunctions, heterojunctions, multijunctions, etc., resulting from stacking layers of different materials can be studied by appropriately selecting characteristic parameters. In this work, examples of cells simulation made with D-AMPS-1D are shown. Particularly, results of Ge photovoltaic devices are presented. The role of the InGaP buffer on the device was studied. Moreover, a comparison of the simulated electrical parameters with experimental results was performed.

3D-printed tracheoesophageal puncture and prosthesis placement simulator.

Science.gov (United States)

Barber, Samuel R; Kozin, Elliott D; Naunheim, Matthew R; Sethi, Rosh; Remenschneider, Aaron K; Deschler, Daniel G

A tracheoesophageal prosthesis (TEP) allows for speech after total laryngectomy. However, TEP placement is technically challenging, requiring a coordinated series of steps. Surgical simulators improve technical skills and reduce operative time. We hypothesize that a reusable 3-dimensional (3D)-printed TEP simulator will facilitate comprehension and rehearsal prior to actual procedures. The simulator was designed using Fusion360 (Autodesk, San Rafael, CA). Components were 3D-printed in-house using an Ultimaker 2+ (Ultimaker, Netherlands). Squid simulated the common tracheoesophageal wall. A Blom-Singer TEP (InHealth Technologies, Carpinteria, CA) replicated placement. Subjects watched an instructional video and completed pre- and post-simulation surveys. The simulator comprised 3D-printed parts: the esophageal lumen and superficial stoma. Squid was placed between components. Ten trainees participated. Significant differences existed between junior and senior residents with surveys regarding anatomy knowledge(p<0.05), technical details(p<0.01), and equipment setup(p<0.01). Subjects agreed that simulation felt accurate, and rehearsal raised confidence in future procedures. A 3D-printed TEP simulator is feasible for surgical training. Simulation involving multiple steps may accelerate technical skills and improve education. Copyright © 2017 Elsevier Inc. All rights reserved.

Realistic and efficient 2D crack simulation

Science.gov (United States)

Yadegar, Jacob; Liu, Xiaoqing; Singh, Abhishek

2010-04-01

Although numerical algorithms for 2D crack simulation have been studied in Modeling and Simulation (M&S) and computer graphics for decades, realism and computational efficiency are still major challenges. In this paper, we introduce a high-fidelity, scalable, adaptive and efficient/runtime 2D crack/fracture simulation system by applying the mathematically elegant Peano-Cesaro triangular meshing/remeshing technique to model the generation of shards/fragments. The recursive fractal sweep associated with the Peano-Cesaro triangulation provides efficient local multi-resolution refinement to any level-of-detail. The generated binary decomposition tree also provides efficient neighbor retrieval mechanism used for mesh element splitting and merging with minimal memory requirements essential for realistic 2D fragment formation. Upon load impact/contact/penetration, a number of factors including impact angle, impact energy, and material properties are all taken into account to produce the criteria of crack initialization, propagation, and termination leading to realistic fractal-like rubble/fragments formation. The aforementioned parameters are used as variables of probabilistic models of cracks/shards formation, making the proposed solution highly adaptive by allowing machine learning mechanisms learn the optimal values for the variables/parameters based on prior benchmark data generated by off-line physics based simulation solutions that produce accurate fractures/shards though at highly non-real time paste. Crack/fracture simulation has been conducted on various load impacts with different initial locations at various impulse scales. The simulation results demonstrate that the proposed system has the capability to realistically and efficiently simulate 2D crack phenomena (such as window shattering and shards generation) with diverse potentials in military and civil M&S applications such as training and mission planning.

Landsat-D thematic mapper simulator

Science.gov (United States)

Flanagan, G. F.; Tilton, E. L., III

The design and testing program for the airborne Landsat-D thematic-mapper simulator (TMS) is summarized. The TMS is intended to provide data similar enough to those expected from Landsat-D to facilitate the development of data-processing software. The design process comprised mainly modifications on the existing MSS-simulator fiber optics, dichroics, and detectors to provide 7-channel coverage of the 0.45-12.3-micron range at 60-deg angle of view, corresponding to a 418-element, 13.8-km-wide ground swath. The TMS is carried on a Lear 23 aircraft operating at 750 km/h and 12-m altitude and equipped with a 15.2-cm aerial mapping camera and a ground-updated inertial navigational system. Agricultural, forestry, and geological trial applications are reviewed, and some sample results are given. The significant improvements predicted for the Landsat-D thematic mapper (relative to the Landsat MSS) are seen as confirmed, with the possible exception of the 120-m-resolution version of channel 7.

Experiment for Integrating Dutch 3d Spatial Planning and Bim for Checking Building Permits

Science.gov (United States)

van Berlo, L.; Dijkmans, T.; Stoter, J.

2013-09-01

This paper presents a research project in The Netherlands in which several SMEs collaborated to create a 3D model of the National spatial planning information. This 2D information system described in the IMRO data standard holds implicit 3D information that can be used to generate an explicit 3D model. The project realized a proof of concept to generate a 3D spatial planning model. The team used the model to integrate it with several 3D Building Information Models (BIMs) described in the open data standard Industry Foundation Classes (IFC). Goal of the project was (1) to generate a 3D BIM model from spatial planning information to be used by the architect during the early design phase, and (2) allow 3D checking of building permits. The team used several technologies like CityGML, BIM clash detection and GeoBIM to explore the potential of this innovation. Within the project a showcase was created with a part of the spatial plan from the city of The Hague. Several BIM models were integrated in the 3D spatial plan of this area. A workflow has been described that demonstrates the benefits of collaboration between the spatial domain and the AEC industry in 3D. The research results in a showcase with conclusions and considerations for both national and international practice.

75 FR 2560 - Issuance of Permits

Science.gov (United States)

2010-01-15

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R9-IA-2010-N006] [96300-1671-0000-P5] Issuance of Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of issuance of permits..., 2009 PH.D, Department of 16, 2009. Cardiology Children's Hospital. Dated: January 8, 2010. Brenda Tapia...

Exact deconstruction of the 6D (2,0) theory

Energy Technology Data Exchange (ETDEWEB)

Hayling, J.; Papageorgakis, C. [Queen Mary Univ. of London (United Kingdom). CRST and School of Physics and Astronomy; Pomoni, E. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany). Theory Group; Rodriguez-Gomez, D. [Oviedo Univ. (Spain). Dept. of Physics

2017-06-15

The dimensional-deconstruction prescription of Arkani-Hamed, Cohen, Kaplan, Karch and Motl provides a mechanism for recovering the A-type (2,0) theories on T{sup 2}, starting from a four-dimensional N=2 circular-quiver theory. We put this conjecture to the test using two exact-counting arguments: In the decompactification limit, we compare the Higgs-branch Hilbert series of the 4D N=2 quiver to the ''half-BPS'' limit of the (2,0) superconformal index. We also compare the full partition function for the 4D quiver on S{sup 4} to the (2,0) partition function on S{sup 4} x T{sup 2}. In both cases we find exact agreement. The partition function calculation sets up a dictionary between exact results in 4D and 6D.

40 CFR 96.323 - CAIR permit contents and term.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false CAIR permit contents and term. 96.323 Section 96.323 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... the permitting authority, as necessary to facilitate coordination of the renewal of the CAIR permit...

New C4D Sensor with a Simulated Inductor

Directory of Open Access Journals (Sweden)

Yingchao Lyu

2016-01-01

Full Text Available A new capacitively coupled contactless conductivity detection (C4D sensor with an improved simulated inductor is developed in this work. The improved simulated inductor is designed on the basis of the Riordan-type floating simulated inductor. With the improved simulated inductor, the negative influence of the coupling capacitances is overcome and the conductivity measurement is implemented by the series resonance principle. The conductivity measurement experiments are carried out in three pipes with different inner diameters of 3.0 mm, 4.6 mm and 6.4 mm, respectively. The experimental results show that the designs of the new C4D sensor and the improved simulated inductor are successful. The maximum relative error of the conductivity measurement is less than 5%. Compared with the C4D sensors using practical inductors, the measurement accuracy of the new C4D sensor is comparable. The research results also indicate that the adjustability of a simulated inductor can reduce the requirement for the AC source and guarantee the interchangeableness. Meanwhile, it is recommended that making the potential of one terminal of a simulated inductor stable is beneficial to the running stability. Furthermore, this work indirectly verifies the possibility and feasibility of the miniaturization of the C4D sensor by using the simulated inductor technique and lays a good foundation for future research work.

RCRA permit modifications and the functional equivalency demonstration: A case study

International Nuclear Information System (INIS)

Kinker, J.; Lyon, W.; Carnes, R.; Loehr, C.; Elsberry, K.; Garcia, P.

1996-01-01

Hazardous waste operating permits issued under the Resource Conservation and Recovery Act (RCRA) often impose requirements, typically by reference to the original permit application, that specific components and equipment be used. Consequently, changing these items, even for the purpose of routine maintenance, may first require that the owner/operator request a potentially time-consuming and costly permit modification. However, the owner/operator may demonstrate that a modification is not required because the planned changes are functionally equivalent, as defined by RCRA, to the original specifications embodied by the permit. The Controlled-Air Incinerator at Los Alamos National Laboratory is scheduled for maintenance and improvements that involve replacement of components. The incinerator's carbon adsorption unit/high efficiency particulate air filtration system, in particular, was redesigned to improve reliability and minimize maintenance. A study was performed to determine whether the redesigned unit would qualify as functionally equivalent to the original component. in performing this study, the following steps were taken: (a) the key performance factors were identified; (b) performance data describing the existing unit were obtained; (c) performance of both the existing and redesigned units was simulated; and (d) the performance data were compared to ascertain whether the components could qualify as functionally equivalent

Rise time of proton cut-off energy in 2D and 3D PIC simulations

Science.gov (United States)

Babaei, J.; Gizzi, L. A.; Londrillo, P.; Mirzanejad, S.; Rovelli, T.; Sinigardi, S.; Turchetti, G.

2017-04-01

The Target Normal Sheath Acceleration regime for proton acceleration by laser pulses is experimentally consolidated and fairly well understood. However, uncertainties remain in the analysis of particle-in-cell simulation results. The energy spectrum is exponential with a cut-off, but the maximum energy depends on the simulation time, following different laws in two and three dimensional (2D, 3D) PIC simulations so that the determination of an asymptotic value has some arbitrariness. We propose two empirical laws for the rise time of the cut-off energy in 2D and 3D PIC simulations, suggested by a model in which the proton acceleration is due to a surface charge distribution on the target rear side. The kinetic energy of the protons that we obtain follows two distinct laws, which appear to be nicely satisfied by PIC simulations, for a model target given by a uniform foil plus a contaminant layer that is hydrogen-rich. The laws depend on two parameters: the scaling time, at which the energy starts to rise, and the asymptotic cut-off energy. The values of the cut-off energy, obtained by fitting 2D and 3D simulations for the same target and laser pulse configuration, are comparable. This suggests that parametric scans can be performed with 2D simulations since 3D ones are computationally very expensive, delegating their role only to a correspondence check. In this paper, the simulations are carried out with the PIC code ALaDyn by changing the target thickness L and the incidence angle α, with a fixed a0 = 3. A monotonic dependence, on L for normal incidence and on α for fixed L, is found, as in the experimental results for high temporal contrast pulses.

The simulation of 3D microcalcification clusters in 2D digital mammography and breast tomosynthesis

International Nuclear Information System (INIS)

Shaheen, Eman; Van Ongeval, Chantal; Zanca, Federica; Cockmartin, Lesley; Marshall, Nicholas; Jacobs, Jurgen; Young, Kenneth C.; Dance, David R.; Bosmans, Hilde

2011-01-01

Purpose: This work proposes a new method of building 3D models of microcalcification clusters and describes the validation of their realistic appearance when simulated into 2D digital mammograms and into breast tomosynthesis images. Methods: A micro-CT unit was used to scan 23 breast biopsy specimens of microcalcification clusters with malignant and benign characteristics and their 3D reconstructed datasets were segmented to obtain 3D models of microcalcification clusters. These models were then adjusted for the x-ray spectrum used and for the system resolution and simulated into 2D projection images to obtain mammograms after image processing and into tomographic sequences of projection images, which were then reconstructed to form 3D tomosynthesis datasets. Six radiologists were asked to distinguish between 40 real and 40 simulated clusters of microcalcifications in two separate studies on 2D mammography and tomosynthesis datasets. Receiver operating characteristic (ROC) analysis was used to test the ability of each observer to distinguish between simulated and real microcalcification clusters. The kappa statistic was applied to assess how often the individual simulated and real microcalcification clusters had received similar scores (''agreement'') on their realistic appearance in both modalities. This analysis was performed for all readers and for the real and the simulated group of microcalcification clusters separately. ''Poor'' agreement would reflect radiologists' confusion between simulated and real clusters, i.e., lesions not systematically evaluated in both modalities as either simulated or real, and would therefore be interpreted as a success of the present models. Results: The area under the ROC curve, averaged over the observers, was 0.55 (95% confidence interval [0.44, 0.66]) for the 2D study, and 0.46 (95% confidence interval [0.29, 0.64]) for the tomosynthesis study, indicating no statistically significant difference between real and simulated

Collaboration system for simulation using commercial Web3D

International Nuclear Information System (INIS)

Okamoto, Koji; Ohkubo, Kohei

2004-01-01

The Web-3D system has been widely used in the internet. It can show the 3D environment easily and friendly. In order to develop the network collaboration system, the Web-3D system is used as the front end of the visualization tool. The 3D geometries have been transferred from the server using HTTP with the viewpoint, one of the commercialized Web-3D. The simulation results are directly transferred to the client using the TCP/IP socket with JAVA. The viewpoint can be controlled by the JAVA, so the transferred simulation data are displayed on the web, in real-time. The multi-client system enables the visualization of the real-time simulation results with remote site. The same results are shown on the remote web site, simultaneously. This means the remote collaboration can be achievable for the real-time simulation. Also, the system has the feedback system, which control the simulation parameter remotely. In this prototype system, the key feature of the collaboration system are discussed using the viewpoint as the frontend. (author)

The European Union's potential for strategic emissions trading through permit sales contracts

International Nuclear Information System (INIS)

Eyckmans, Johan; Hagem, Cathrine

2011-01-01

Strategic market behavior by permit sellers will harm the European Union (EU) as it is expected to become a large net buyer of permits in a follow-up agreement to the Kyoto Protocol. In this paper, we explore how the EU could benefit from making permit trade agreements with non-EU countries. These trade agreements involve permit sales requirement, complemented by a financial transfer from the EU to the other contract party. Such agreements would enable the EU to act strategically in the permit market on behalf of its member states, although each member state is assumed to behave as a price taker in the permit market. Using a stylized numerical simulation model, we show that an appropriately designed permit trade agreement between the EU and China could significantly cut the EU's total compliance cost. This result is robust for a wide range of parameterizations of the simulation model. (author)

78 FR 27249 - Endangered Species Recovery Permit Applications

Science.gov (United States)

2013-05-09

... purpose of enhancing the species' survival. Permit No. TE-99477A Applicant: Benjamin S. Wallace, Fairfield...-99473A Applicant: Joseph D. Henry, San Diego, California The applicant requests a permit to take (capture...

Cdc20 mediates D-box-dependent degradation of Sp100

International Nuclear Information System (INIS)

Wang, Ran; Li, Ke-min; Zhou, Cai-hong; Xue, Jing-lun; Ji, Chao-neng; Chen, Jin-zhong

2011-01-01

Highlights: ► Cdc20 is a co-activator of APC/C complex. ► Cdc20 recruits Sp100 and mediates its degradation. ► The D-box of Sp100 is required for Cdc20-mediated degradation. ► Sp100 expresses consistently at both the mRNA and protein levels in cell cycle. -- Abstract: Cdc20 is a co-activator of the anaphase-promoting complex/cyclosome (APC/C complex), which recruits substrates at particular phases of the cell cycle and mediates their degradation. Sp100 is a PML-NB scaffold protein, which localizes to nuclear particles during interphase and disperses from them during mitosis, participates in viral resistance, transcriptional regulation, and apoptosis. However, its metabolism during the cell cycle has not yet been fully characterized. We found a putative D-box in Sp100 using the Eukaryotic Linear Motif (ELM) predictor database. The putative D-box of Sp100 was verified by mutational analysis. Overexpression of Cdc20 resulted in decreased levels of both endogenous Sp100 protein and overexpressed Sp100 mRNA in HEK 293 cells. Only an overexpressed D-box deletion mutant of Sp100 accumulated in HEK293 cells that also overexpressed Cdc20. Cdc20 knockdown by cdc20 specific siRNA resulted in increased Sp100 protein levels in cells. Furthermore, we discovered that the Cdc20 mediated degradation of Sp100 is diminished by the proteasome inhibitor MG132, which suggests that the ubiquitination pathway is involved in this process. However, unlike the other Cdc20 substrates, which display oscillating protein levels, the level of Sp100 protein remains constant throughout the cell cycle. Additionally, both overexpression and knockdown of endogenous Sp100 had no effect on the cell cycle. Our results suggested that sp100 is a novel substrate of Cdc20 and it is degraded by the ubiquitination pathway. The intact D-box of Sp100 was necessary for this process. These findings expand our knowledge of both Sp100 and Cdc20 as well as their role in ubiquitination.

Simulation of DIII-D Flat q Discharges

International Nuclear Information System (INIS)

Kessel, C.E.; Garofalo, A.; Terpstra, T.

2004-01-01

The Advanced Tokamak plasma configuration has significant potential for the economical production of fusion power. Research on various tokamak experiments are pursuing these plasmas to establish high β, high bootstrap current fraction, 100% noninductive current, and good energy confinement, in a quasi-stationary state. One candidate is the flat q discharge produced in DIII-D, where the safety factor varies from 2.0 on axis, to slightly below 2.0 at the minimum, and then rises to about 3.5 at the 95% surface. This plasma is prototypical of those studied for power plants in the ARIES tokamak studies. The plasma is produced by ramping up the plasma current and ramping down the toroidal field throughout the discharge. The plasma current reaches 1.65 MA, and the toroidal field goes from 2.25 to 1.6 T. The q min remains high and at large radius, ρ ∼ 0.6. The plasma establishes an internal transport barrier in the ion channel, and transitions to H-mode. The free-boundary Tokamak Simulation Code (TSC) is being used to model the discharge and project the impact of changes in the plasma current, toroidal field, and injected power programming

Analysis of convection-permitting simulations for capturing heavy rainfall events over Myanmar Region

Science.gov (United States)

Acierto, R. A. E.; Kawasaki, A.

2017-12-01

Perennial flooding due to heavy rainfall events causes strong impacts on the society and economy. With increasing pressures of rapid development and potential for climate change impacts, Myanmar experiences a rapid increase in disaster risk. Heavy rainfall hazard assessment is key on quantifying such disaster risk in both current and future conditions. Downscaling using Regional Climate Models (RCM) such as Weather Research and Forecast model have been used extensively for assessing such heavy rainfall events. However, usage of convective parameterizations can introduce large errors in simulating rainfall. Convective-permitting simulations have been used to deal with this problem by increasing the resolution of RCMs to 4km. This study focuses on the heavy rainfall events during the six-year (2010-2015) wet period season from May to September in Myanmar. The investigation primarily utilizes rain gauge observation for comparing downscaled heavy rainfall events in 4km resolution using ERA-Interim as boundary conditions using 12km-4km one-way nesting method. The study aims to provide basis for production of high-resolution climate projections over Myanmar in order to contribute for flood hazard and risk assessment.

Front instabilities and invasiveness of simulated 3D avascular tumors.

Directory of Open Access Journals (Sweden)

Nikodem J Poplawski

2010-05-01

Full Text Available We use the Glazier-Graner-Hogeweg model to simulate three-dimensional (3D, single-phenotype, avascular tumors growing in an homogeneous tissue matrix (TM supplying a single limiting nutrient. We study the effects of two parameters on tumor morphology: a diffusion-limitation parameter defined as the ratio of the tumor-substrate consumption rate to the substrate-transport rate, and the tumor-TM surface tension. This initial model omits necrosis and oxidative/hypoxic metabolism effects, which can further influence tumor morphology, but our simplified model still shows significant parameter dependencies. The diffusion-limitation parameter determines whether the growing solid tumor develops a smooth (noninvasive or fingered (invasive interface, as in our earlier two-dimensional (2D simulations. The sensitivity of 3D tumor morphology to tumor-TM surface tension increases with the size of the diffusion-limitation parameter, as in 2D. The 3D results are unexpectedly close to those in 2D. Our results therefore may justify using simpler 2D simulations of tumor growth, instead of more realistic but more computationally expensive 3D simulations. While geometrical artifacts mean that 2D sections of connected 3D tumors may be disconnected, the morphologies of 3D simulated tumors nevertheless correlate with the morphologies of their 2D sections, especially for low-surface-tension tumors, allowing the use of 2D sections to partially reconstruct medically-important 3D-tumor structures.

77 FR 10183 - Reissuance of Nationwide Permits

Science.gov (United States)

2012-02-21

... Civil Works Program (Engineer Circular 1165- 2-211). The current Engineer Circular applies to Corps..., Corps of Engineers Reissuance of Nationwide Permits; Notice #0;#0;Federal Register / Vol. 77 , No. 34..., Corps of Engineers RIN 0710-AA71 Reissuance of Nationwide Permits AGENCY: Army Corps of Engineers, DoD...

EEG simulation by 2D interconnected chaotic oscillators

Energy Technology Data Exchange (ETDEWEB)

Kubany, Adam, E-mail: adamku@bgu.ac.i [Department of Industrial Engineering and Management, Ben-Gurion University of the Negev, P.O. Box 653, Beer-Sheva 84105 (Israel); Mhabary, Ziv; Gontar, Vladimir [Department of Industrial Engineering and Management, Ben-Gurion University of the Negev, P.O. Box 653, Beer-Sheva 84105 (Israel)

2011-01-15

Research highlights: ANN of 2D interconnected chaotic oscillators is explored for EEG simulation. An inverse problem solution (PRCGA) is proposed. Good matching between the simulated and experimental EEG signals has been achieved. - Abstract: An artificial neuronal network composed by 2D interconnected chaotic oscillators is explored for brain waves (EEG) simulation. For the inverse problem solution a parallel real-coded genetic algorithm (PRCGA) is proposed. In order to conduct thorough comparison between the simulated and target signal characteristics, a spectrum analysis of the signals is undertaken. A good matching between the theoretical and experimental EEG signals has been achieved. Numerical results of calculations are presented and discussed.

EEG simulation by 2D interconnected chaotic oscillators

International Nuclear Information System (INIS)

Kubany, Adam; Mhabary, Ziv; Gontar, Vladimir

2011-01-01

Research highlights: → ANN of 2D interconnected chaotic oscillators is explored for EEG simulation. → An inverse problem solution (PRCGA) is proposed. → Good matching between the simulated and experimental EEG signals has been achieved. - Abstract: An artificial neuronal network composed by 2D interconnected chaotic oscillators is explored for brain waves (EEG) simulation. For the inverse problem solution a parallel real-coded genetic algorithm (PRCGA) is proposed. In order to conduct thorough comparison between the simulated and target signal characteristics, a spectrum analysis of the signals is undertaken. A good matching between the theoretical and experimental EEG signals has been achieved. Numerical results of calculations are presented and discussed.

Cdc20 mediates D-box-dependent degradation of Sp100

Energy Technology Data Exchange (ETDEWEB)

Wang, Ran; Li, Ke-min; Zhou, Cai-hong; Xue, Jing-lun [State Key Laboratory of Genetic Engineering, Institute of Genetics, School of Life Science, Fudan University, Shanghai (China); Ji, Chao-neng, E-mail: Chnji@fudan.edu.cn [State Key Laboratory of Genetic Engineering, Institute of Genetics, School of Life Science, Fudan University, Shanghai (China); Chen, Jin-zhong, E-mail: kingbellchen@fudan.edu.cn [State Key Laboratory of Genetic Engineering, Institute of Genetics, School of Life Science, Fudan University, Shanghai (China)

2011-12-02

Highlights: Black-Right-Pointing-Pointer Cdc20 is a co-activator of APC/C complex. Black-Right-Pointing-Pointer Cdc20 recruits Sp100 and mediates its degradation. Black-Right-Pointing-Pointer The D-box of Sp100 is required for Cdc20-mediated degradation. Black-Right-Pointing-Pointer Sp100 expresses consistently at both the mRNA and protein levels in cell cycle. -- Abstract: Cdc20 is a co-activator of the anaphase-promoting complex/cyclosome (APC/C complex), which recruits substrates at particular phases of the cell cycle and mediates their degradation. Sp100 is a PML-NB scaffold protein, which localizes to nuclear particles during interphase and disperses from them during mitosis, participates in viral resistance, transcriptional regulation, and apoptosis. However, its metabolism during the cell cycle has not yet been fully characterized. We found a putative D-box in Sp100 using the Eukaryotic Linear Motif (ELM) predictor database. The putative D-box of Sp100 was verified by mutational analysis. Overexpression of Cdc20 resulted in decreased levels of both endogenous Sp100 protein and overexpressed Sp100 mRNA in HEK 293 cells. Only an overexpressed D-box deletion mutant of Sp100 accumulated in HEK293 cells that also overexpressed Cdc20. Cdc20 knockdown by cdc20 specific siRNA resulted in increased Sp100 protein levels in cells. Furthermore, we discovered that the Cdc20 mediated degradation of Sp100 is diminished by the proteasome inhibitor MG132, which suggests that the ubiquitination pathway is involved in this process. However, unlike the other Cdc20 substrates, which display oscillating protein levels, the level of Sp100 protein remains constant throughout the cell cycle. Additionally, both overexpression and knockdown of endogenous Sp100 had no effect on the cell cycle. Our results suggested that sp100 is a novel substrate of Cdc20 and it is degraded by the ubiquitination pathway. The intact D-box of Sp100 was necessary for this process. These findings expand

17 CFR 240.15d-20 - Plain English presentation of specified information.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Plain English presentation of specified information. 240.15d-20 Section 240.15d-20 Commodity and Securities Exchanges SECURITIES AND... Regulations Under the Securities Exchange Act of 1934 Other Reports § 240.15d-20 Plain English presentation of...

A translator and simulator for the Burroughs D machine

Science.gov (United States)

Roberts, J.

1972-01-01

The D Machine is described as a small user microprogrammable computer designed to be a versatile building block for such diverse functions as: disk file controllers, I/O controllers, and emulators. TRANSLANG is an ALGOL-like language, which allows D Machine users to write microprograms in an English-like format as opposed to creating binary bit pattern maps. The TRANSLANG translator parses TRANSLANG programs into D Machine microinstruction bit patterns which can be executed on the D Machine simulator. In addition to simulation and translation, the two programs also offer several debugging tools, such as: a full set of diagnostic error messages, register dumps, simulated memory dumps, traces on instructions and groups of instructions, and breakpoints.

3D Model Optimization of Four-Facet Drill for 3D Drilling Simulation

Directory of Open Access Journals (Sweden)

Buranský Ivan

2016-09-01

Full Text Available The article is focused on optimization of four-facet drill for 3D drilling numerical modelling. For optimization, the process of reverse engineering by PowerShape software was used. The design of four-facet drill was created in NumrotoPlus software. The modified 3D model of the drill was used in the numerical analysis of cutting forces. Verification of the accuracy of 3D models for reverse engineering was implemented using the colour deviation maps. The CAD model was in the STEP format. For simulation software, 3D model in the STEP format is ideal. STEP is a solid model. Simulation software automatically splits the 3D model into finite elements. The STEP model was therefore more suitable than the STL model.

Radiocompetitive estimation of 25-hydroxyvitamin D human serum

International Nuclear Information System (INIS)

Guillemant, S.; Kremer, R.

1978-01-01

A radiocompetitive estimation of 25-hydroxyvitamin D in human serum is described. After extraction, a stage of purification by chromatography on a Sephadex LH 20 column permits separation of 25-hydroxyvitamin D from Vitamin D and other metabolites. The reaction of radiocompetition uses as tracer tritialed 25-hydroxycholecalciferol and as source of binding protein, rat renal cytosol. The characteristics of the binding protein and the presence in human plasma of significant quantities of 24,25-dihydroxyvitamin D render necesssary the chromatographic stage. This technic permits one to measure simply and specifically 25-hydroxyvitamin D in the human serum, of which normal levels (average + - standard deviation) are 12.88 + - 5.42 μg/l (3.2.10 -8 + - 1.35.10 -8 mol/l) [fr

4D dose simulation in volumetric arc therapy: Accuracy and affecting parameters

Science.gov (United States)

Werner, René

2017-01-01

Radiotherapy of lung and liver lesions has changed from normofractioned 3D-CRT to stereotactic treatment in a single or few fractions, often employing volumetric arc therapy (VMAT)-based techniques. Potential unintended interference of respiratory target motion and dynamically changing beam parameters during VMAT dose delivery motivates establishing 4D quality assurance (4D QA) procedures to assess appropriateness of generated VMAT treatment plans when taking into account patient-specific motion characteristics. Current approaches are motion phantom-based 4D QA and image-based 4D VMAT dose simulation. Whereas phantom-based 4D QA is usually restricted to a small number of measurements, the computational approaches allow simulating many motion scenarios. However, 4D VMAT dose simulation depends on various input parameters, influencing estimated doses along with mitigating simulation reliability. Thus, aiming at routine use of simulation-based 4D VMAT QA, the impact of such parameters as well as the overall accuracy of the 4D VMAT dose simulation has to be studied in detail–which is the topic of the present work. In detail, we introduce the principles of 4D VMAT dose simulation, identify influencing parameters and assess their impact on 4D dose simulation accuracy by comparison of simulated motion-affected dose distributions to corresponding dosimetric motion phantom measurements. Exploiting an ITV-based treatment planning approach, VMAT treatment plans were generated for a motion phantom and different motion scenarios (sinusoidal motion of different period/direction; regular/irregular motion). 4D VMAT dose simulation results and dose measurements were compared by local 3% / 3 mm γ-evaluation, with the measured dose distributions serving as ground truth. Overall γ-passing rates of simulations and dynamic measurements ranged from 97% to 100% (mean across all motion scenarios: 98% ± 1%); corresponding values for comparison of different day repeat measurements were

Program for simulation of reduction of effluents

NARCIS (Netherlands)

Grenier, P.; Vilette, P.; Mignonac, J.M.; Leclercq, P.A.; Gayda, A.; Cosson, J.L.; Moletta, R.; Racault, Y.

1994-01-01

Food industry and wineries in particular are responsible for a significant part of the org. industrial pollution in France. This pollution has been characterized at the Caves du Sieur d'Arques winery. Dynamic simulation of waste rejection should permit to est. the variability of inputs at the waste

Fast 2D Fluid-Analytical Simulation of IEDs and Plasma Uniformity in Multi-frequency CCPs

Science.gov (United States)

Kawamura, E.; Lieberman, M. A.; Graves, D. B.

2014-10-01

A fast 2D axisymmetric fluid-analytical model using the finite elements tool COMSOL is interfaced with a 1D particle-in-cell (PIC) code to study ion energy distributions (IEDs) in multi-frequency argon capacitively coupled plasmas (CCPs). A bulk fluid plasma model which solves the time-dependent plasma fluid equations is coupled with an analytical sheath model which solves for the sheath parameters. The fluid-analytical results are used as input to a PIC simulation of the sheath region of the discharge to obtain the IEDs at the wafer electrode. Each fluid-analytical-PIC simulation on a moderate 2.2 GHz CPU workstation with 8 GB of memory took about 15-20 minutes. The 2D multi-frequency fluid-analytical model was compared to 1D PIC simulations of a symmetric parallel plate discharge, showing good agreement. Fluid-analytical simulations of a 2/60/162 MHz argon CCP with a typical asymmetric reactor geometry were also conducted. The low 2 MHz frequency controlled the sheath width and voltage while the higher frequencies controlled the plasma production. A standing wave was observable at the highest frequency of 162 MHz. Adding 2 MHz power to a 60 MHz discharge or 162 MHz to a dual frequency 2 MHz/60 MHz discharge enhanced the plasma uniformity. This work was supported by the Department of Energy Office of Fusion Energy Science Contract DE-SC000193, and in part by gifts from Lam Research Corporation and Micron Corporation.

Visual-Simulation-Based Personalized Garment Block Design Method for Physically Disabled People with Scoliosis (PDPS

Directory of Open Access Journals (Sweden)

Hong Yan

2018-03-01

Full Text Available This research presented a novel method using 3D simulation methods to design customized garments for physically disabled people with scoliosis (PDPS. The proposed method is based on the virtual human model created from 3D scanning, permitting to simulate the consumer’s morphological shape with atypical physical deformations. Next, customized 2D and 3D virtual garment prototyping tools will be used to create products through interactions. The proposed 3D garment design method is based on the concept of knowledge-based design, using the design knowledge and process already applied to normal body shapes successfully. The characters of the PDPS and the relationship between human body and garment are considered in the prototyping process. As a visualized collaborative design process, the communication between designer and consumer is ensured, permitting to adapt the finished product to disabled people afflicted with severe scoliosis.

Simulation Of Seawater Intrusion With 2D And 3D Models: Nauru Island Case Study

Science.gov (United States)

Ghassemi, F.; Jakeman, A. J.; Jacobson, G.; Howard, K. W. F.

1996-03-01

With the advent of large computing capacities during the past few decades, sophisticated models have been developed for the simulation of seawater intrusion in coastal and island aquifers. Currently, several models are commercially available for the simulation of this problem. This paper describes the mathematical basis and application of the SUTRA and HST3D models to simulate seawater intrusion in Nauru Island, in the central Pacific Ocean. A comparison of the performance and limitations of these two models in simulating a real problem indicates that three-dimensional simulation of seawater intrusion with the HST3D model has the major advantage of being able to specify natural boundary conditions as well as pumping stresses. However, HST3D requires a small grid size and short time steps in order to maintain numerical stability and accuracy. These requirements lead to solution of a large set of linear equations that requires the availability of powerful computing facilities in terms of memory and computing speed. Combined results of the two simulation models indicate a safe pumping rate of 400 m3/d for the aquifer on Nauru Island, where additional fresh water is presently needed for the rehabilitation of mined-out land.

40 CFR 96.85 - NOX Budget opt-in permit contents.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false NOX Budget opt-in permit contents. 96... (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS Individual Unit Opt-ins § 96.85 NOX Budget opt-in permit contents. (a) Each NOX Budget opt-in permit...

40 CFR 97.85 - NOX Budget opt-in permit contents.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false NOX Budget opt-in permit contents. 97... (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS Individual Unit Opt-ins. § 97.85 NOX Budget opt-in permit contents. (a) Each NOX Budget opt-in permit will contain all elements...

SimVascular 2.0: an Integrated Open Source Pipeline for Image-Based Cardiovascular Modeling and Simulation

Science.gov (United States)

Lan, Hongzhi; Merkow, Jameson; Updegrove, Adam; Schiavazzi, Daniele; Wilson, Nathan; Shadden, Shawn; Marsden, Alison

2015-11-01

SimVascular (www.simvascular.org) is currently the only fully open source software package that provides a complete pipeline from medical image based modeling to patient specific blood flow simulation and analysis. It was initially released in 2007 and has contributed to numerous advances in fundamental hemodynamics research, surgical planning, and medical device design. However, early versions had several major barriers preventing wider adoption by new users, large-scale application in clinical and research studies, and educational access. In the past years, SimVascular 2.0 has made significant progress by integrating open source alternatives for the expensive commercial libraries previously required for anatomic modeling, mesh generation and the linear solver. In addition, it simplified the across-platform compilation process, improved the graphical user interface and launched a comprehensive documentation website. Many enhancements and new features have been incorporated for the whole pipeline, such as 3-D segmentation, Boolean operation for discrete triangulated surfaces, and multi-scale coupling for closed loop boundary conditions. In this presentation we will briefly overview the modeling/simulation pipeline and advances of the new SimVascular 2.0.

3D Surgical Simulation

OpenAIRE

Cevidanes, Lucia; Tucker, Scott; Styner, Martin; Kim, Hyungmin; Chapuis, Jonas; Reyes, Mauricio; Proffit, William; Turvey, Timothy; Jaskolka, Michael

2010-01-01

This paper discusses the development of methods for computer-aided jaw surgery. Computer-aided jaw surgery allows us to incorporate the high level of precision necessary for transferring virtual plans into the operating room. We also present a complete computer-aided surgery (CAS) system developed in close collaboration with surgeons. Surgery planning and simulation include construction of 3D surface models from Cone-beam CT (CBCT), dynamic cephalometry, semi-automatic mirroring, interactive ...

Molecular dynamics simulations of radiation damage in D019 Ti3Al intermetallic compound

International Nuclear Information System (INIS)

Voskoboinikov, Roman E.

2013-01-01

Molecular dynamics (MD) has been applied to simulate the radiation damage created in displacement cascades in D0 19 Ti 3 Al structural intermetallics. Collision cascades formed by the recoil of either Al or Ti primary knock-on atoms (PKA) with energy E PKA = 5, 10, 15 or 20 keV were considered in Ti 3 Al single crystals at T = 100, 300, 600 and 900 K. At least 24 different cascades for each (E PKA , T, PKA type) set were simulated. A comprehensive treatment of the modelling results has been carried out. We have evaluated the number of Frenkel pairs, fraction of Al and Ti vacancies, self-interstitial atoms and anti-sites as a function of (E PKA ,T, PKA type). Preferred formation of both Al vacancies and self-interstitial atoms in D0 19 Ti 3 Al exposed to irradiation has been detected

Microbial Enhanced Oil Recovery: 3D Simulation with Gravity Effects

DEFF Research Database (Denmark)

Nielsen, Sidsel Marie; Jessen, K.; Shapiro, Alexander

2010-01-01

Microbial enhanced oil recovery (MEOR) utilizes the activity of microorganisms, where microorganisms simultaneously grow in a reservoir and convert substrate into recovery enhancing products (usually, surfactants). In order to predict the performance of a MEOR process, a simulation tool is required...... using an operator splitting technique. To the best of our knowledge, this has resulted in the first full 3D MEOR streamline simulator. For verification purposes, we compare results from our streamline MEOR simulator to those of a conventional finite difference approach for 1D and 2D displacement...

40 CFR 96.223 - CAIR permit contents and term.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false CAIR permit contents and term. 96.223 Section 96.223 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... necessary to facilitate coordination of the renewal of the CAIR permit with issuance, revision, or renewal...

40 CFR 96.123 - CAIR permit contents and term.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false CAIR permit contents and term. 96.123 Section 96.123 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... necessary to facilitate coordination of the renewal of the CAIR permit with issuance, revision, or renewal...

40 CFR 97.323 - CAIR permit contents and term.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false CAIR permit contents and term. 97.323 Section 97.323 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... authority, as necessary to facilitate coordination of the renewal of the CAIR permit with issuance, revision...

An Evaluative Review of Simulated Dynamic Smart 3d Objects

Science.gov (United States)

Romeijn, H.; Sheth, F.; Pettit, C. J.

2012-07-01

Three-dimensional (3D) modelling of plants can be an asset for creating agricultural based visualisation products. The continuum of 3D plants models ranges from static to dynamic objects, also known as smart 3D objects. There is an increasing requirement for smarter simulated 3D objects that are attributed mathematically and/or from biological inputs. A systematic approach to plant simulation offers significant advantages to applications in agricultural research, particularly in simulating plant behaviour and the influences of external environmental factors. This approach of 3D plant object visualisation is primarily evident from the visualisation of plants using photographed billboarded images, to more advanced procedural models that come closer to simulating realistic virtual plants. However, few programs model physical reactions of plants to external factors and even fewer are able to grow plants based on mathematical and/or biological parameters. In this paper, we undertake an evaluation of plant-based object simulation programs currently available, with a focus upon the components and techniques involved in producing these objects. Through an analytical review process we consider the strengths and weaknesses of several program packages, the features and use of these programs and the possible opportunities in deploying these for creating smart 3D plant-based objects to support agricultural research and natural resource management. In creating smart 3D objects the model needs to be informed by both plant physiology and phenology. Expert knowledge will frame the parameters and procedures that will attribute the object and allow the simulation of dynamic virtual plants. Ultimately, biologically smart 3D virtual plants that react to changes within an environment could be an effective medium to visually represent landscapes and communicate land management scenarios and practices to planners and decision-makers.

Simulating 3D deformation using connected polygons

Science.gov (United States)

Tarigan, J. T.; Jaya, I.; Hardi, S. M.; Zamzami, E. M.

2018-03-01

In modern 3D application, interaction between user and the virtual world is one of an important factor to increase the realism. This interaction can be visualized in many forms; one of them is object deformation. There are many ways to simulate object deformation in virtual 3D world; each comes with different level of realism and performance. Our objective is to present a new method to simulate object deformation by using a graph-connected polygon. In this solution, each object contains multiple level of polygons in different level of volume. The proposed solution focusses on performance rather while maintaining the acceptable level of realism. In this paper, we present the design and implementation of our solution and show that this solution is usable in performance sensitive 3D application such as games and virtual reality.

Time-Domain Simulation of RF Couplers

International Nuclear Information System (INIS)

Smithe, David; Carlsson, Johan; Austin, Travis

2009-01-01

We have developed a finite-difference time-domain (FDTD) fluid-like approach to integrated plasma-and-coupler simulation [1], and show how it can be used to model LH and ICRF couplers in the MST and larger tokamaks.[2] This approach permits very accurate 3-D representation of coupler geometry, and easily includes non-axi-symmetry in vessel wall, magnetic equilibrium, and plasma density. The plasma is integrated with the FDTD Maxwell solver in an implicit solve that steps over electron time-scales, and permits tenuous plasma in the coupler itself, without any need to distinguish or interface between different regions of vacuum and/or plasma. The FDTD algorithm is also generalized to incorporate a time-domain sheath potential [3] on metal structures within the simulation, to look for situations where the sheath potential might generate local sputtering opportunities. Benchmarking of the time-domain sheath algorithm has been reported in the references. Finally, the time-domain software [4] permits the use of particles, either as field diagnostic (test particles) or to self-consistently compute plasma current from the applied RF power.

Design of 3D simulation engine for oilfield safety training

Science.gov (United States)

Li, Hua-Ming; Kang, Bao-Sheng

2015-03-01

Aiming at the demand for rapid custom development of 3D simulation system for oilfield safety training, this paper designs and implements a 3D simulation engine based on script-driven method, multi-layer structure, pre-defined entity objects and high-level tools such as scene editor, script editor, program loader. A scripting language been defined to control the system's progress, events and operating results. Training teacher can use this engine to edit 3D virtual scenes, set the properties of entity objects, define the logic script of task, and produce a 3D simulation training system without any skills of programming. Through expanding entity class, this engine can be quickly applied to other virtual training areas.

Application of computer virtual simulation technology in 3D animation production

Science.gov (United States)

Mo, Can

2017-11-01

In the continuous development of computer technology, the application system of virtual simulation technology has been further optimized and improved. It also has been widely used in various fields of social development, such as city construction, interior design, industrial simulation and tourism teaching etc. This paper mainly introduces the virtual simulation technology used in 3D animation. Based on analyzing the characteristics of virtual simulation technology, the application ways and means of this technology in 3D animation are researched. The purpose is to provide certain reference for the 3D effect promotion days after.

3D Simulations of NIF Wetted Foam Experiments to Understand the Transition from 2D to 3D Implosion Behavior

Science.gov (United States)

Haines, Brian; Olson, Richard; Yi, Austin; Zylstra, Alex; Peterson, Robert; Bradley, Paul; Shah, Rahul; Wilson, Doug; Kline, John; Leeper, Ramon; Batha, Steve

2017-10-01

The high convergence ratio (CR) of layered Inertial Confinement Fusion capsule implosions contribute to high performance in 1D simulations yet make them more susceptible to hydrodynamic instabilities, contributing to the development of 3D flows. The wetted foam platform is an approach to hot spot ignition to achieve low-to-moderate convergence ratios in layered implosions on the NIF unobtainable using an ice layer. Detailed high-resolution modeling of these experiments in 2D and 3D, including all known asymmetries, demonstrates that 2D hydrodynamics explain capsule performance at CR 12 but become less suitable as the CR increases. Mechanisms for this behavior and detailed comparisons of simulations to experiments on NIF will be presented. To evaluate the tradeoff between increased instability and improved 1D performance, we present a full-scale wetted foam capsule design with 17 Simulations predict that, given currently achievable levels of asymmetry, their effects negate all advantages of increased CR.

40 CFR 97.123 - CAIR permit contents and term.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false CAIR permit contents and term. 97.123 Section 97.123 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... facilitate coordination of the renewal of the CAIR permit with issuance, revision, or renewal of the CAIR NOX...

fdtd Semiconductor Microlaser Simulator v. 2.0

Energy Technology Data Exchange (ETDEWEB)

2009-01-29

This software simulates the transient optical response of a system of in-plane semiconductor lasers/waveguides of almost arbitrary 2D complexity using the effective index approximation. Gain is calculated by solving a 3D transport equation from an arbitrary contact geometry and epi structure to get an input current density to the active region, followed by a diffusion equation for carriers in that layer. The gain is saturable and frequency dependent so that output powers and frequency spectrum/longitudinal modes are predicted. Solution is by the finite-difference time-domain method on a 2D triangular grid, so that propagation in any direction along the epi plan is allowed, and arbitrary laser/waveguide shapes can be modeled, including rings. Runtime considerations, however, limit the practical solution region to approximately 500 microns**2 so that the applicability of this code is primarily limited to micro-resinators. Modeling of standard-edge-emitting semiconductor lasers is better accomplished using algorithms based on bi-directional beam propagation.

40 CFR 96.24 - Effective date of initial NOX Budget permit.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Effective date of initial NOX Budget... PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS Permits § 96.24 Effective date of initial NOX Budget permit. The initial NOX Budget permit...

3D printing to simulate laparoscopic choledochal surgery.

Science.gov (United States)

Burdall, Oliver C; Makin, Erica; Davenport, Mark; Ade-Ajayi, Niyi

2016-05-01

Laparoscopic simulation has transformed skills acquisition for many procedures. However, realistic nonbiological simulators for complex reconstructive surgery are rare. Life-like tactile feedback is particularly difficult to reproduce. Technological innovations may contribute novel solutions to these shortages. We describe a hybrid model, harnessing 3D technology to simulate laparoscopic choledochal surgery for the first time. Digital hepatic anatomy images and standard laparoscopic trainer dimensions were employed to create an entry level laparoscopic choledochal surgery model. The information was fed into a 3D systems project 660pro with visijet pxl core powder to create a free standing liver mold. This included a cuboid portal in which to slot disposable hybrid components representing hepatic and pancreatic ducts and choledochal cyst. The mold was used to create soft silicone replicas with T28 resin and T5 fast catalyst. The model was assessed at a national pediatric surgery training day. The 10 delegates that trialed the simulation felt that the tactile likeness was good (5.6/10±1.71, 10=like the real thing), was not too complex (6.2/10±1.35; where 1=too simple, 10=too complicated), and generally very useful (7.36/10±1.57, 10=invaluable). 100% stated that they felt they could reproduce this in their own centers, and 100% would recommend this simulation to colleagues. Though this first phase choledochal cyst excision simulation requires further development, 3D printing provides a useful means of creating specific and detailed simulations for rare and complex operations with huge potential for development. Copyright © 2016. Published by Elsevier Inc.

3D-printed pediatric endoscopic ear surgery simulator for surgical training.

Science.gov (United States)

Barber, Samuel R; Kozin, Elliott D; Dedmon, Matthew; Lin, Brian M; Lee, Kyuwon; Sinha, Sumi; Black, Nicole; Remenschneider, Aaron K; Lee, Daniel J

2016-11-01

Surgical simulators are designed to improve operative skills and patient safety. Transcanal Endoscopic Ear Surgery (TEES) is a relatively new surgical approach with a slow learning curve due to one-handed dissection. A reusable and customizable 3-dimensional (3D)-printed endoscopic ear surgery simulator may facilitate the development of surgical skills with high fidelity and low cost. Herein, we aim to design, fabricate, and test a low-cost and reusable 3D-printed TEES simulator. The TEES simulator was designed in computer-aided design (CAD) software using anatomic measurements taken from anthropometric studies. Cross sections from external auditory canal samples were traced as vectors and serially combined into a mesh construct. A modified tympanic cavity with a modular testing platform for simulator tasks was incorporated. Components were fabricated using calcium sulfate hemihydrate powder and multiple colored infiltrants via a commercial inkjet 3D-printing service. All components of a left-sided ear were printed to scale. Six right-handed trainees completed three trials each. Mean trial time (n = 3) ranged from 23.03 to 62.77 s using the dominant hand for all dissection. Statistically significant differences between first and last completion time with the dominant hand (p 3D-printed simulator is feasible for TEES simulation. Otolaryngology training programs with access to a 3D printer may readily fabricate a TEES simulator, resulting in inexpensive yet high-fidelity surgical simulation. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

40 CFR 97.223 - CAIR permit contents and term.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false CAIR permit contents and term. 97.223 Section 97.223 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... facilitate coordination of the renewal of the CAIR permit with issuance, revision, or renewal of the CAIR SO2...

File list: NoD.Gon.20.AllAg.Spermatocytes [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Gon.20.AllAg.Spermatocytes mm9 No description Gonad Spermatocytes SRX336649,SRX...336650 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Gon.20.AllAg.Spermatocytes.bed ...

Stability and accuracy of 3D neutron transport simulations using the 2D/1D method in MPACT

International Nuclear Information System (INIS)

Collins, Benjamin; Stimpson, Shane; Kelley, Blake W.; Young, Mitchell T.H.; Kochunas, Brendan; Graham, Aaron; Larsen, Edward W.; Downar, Thomas; Godfrey, Andrew

2016-01-01

A consistent “2D/1D” neutron transport method is derived from the 3D Boltzmann transport equation, to calculate fuel-pin-resolved neutron fluxes for realistic full-core Pressurized Water Reactor (PWR) problems. The 2D/1D method employs the Method of Characteristics to discretize the radial variables and a lower order transport solution to discretize the axial variable. This paper describes the theory of the 2D/1D method and its implementation in the MPACT code, which has become the whole-core deterministic neutron transport solver for the Consortium for Advanced Simulations of Light Water Reactors (CASL) core simulator VERA-CS. Several applications have been performed on both leadership-class and industry-class computing clusters. Results are presented for whole-core solutions of the Watts Bar Nuclear Power Station Unit 1 and compared to both continuous-energy Monte Carlo results and plant data.

Stability and accuracy of 3D neutron transport simulations using the 2D/1D method in MPACT

Energy Technology Data Exchange (ETDEWEB)

Collins, Benjamin, E-mail: collinsbs@ornl.gov [Oak Ridge National Laboratory, One Bethel Valley Rd., Oak Ridge, TN 37831 (United States); Stimpson, Shane, E-mail: stimpsonsg@ornl.gov [Oak Ridge National Laboratory, One Bethel Valley Rd., Oak Ridge, TN 37831 (United States); Kelley, Blake W., E-mail: kelleybl@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Young, Mitchell T.H., E-mail: youngmit@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Kochunas, Brendan, E-mail: bkochuna@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Graham, Aaron, E-mail: aarograh@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Larsen, Edward W., E-mail: edlarsen@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Downar, Thomas, E-mail: downar@umich.edu [Department of Nuclear Engineering and Radiological Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Godfrey, Andrew, E-mail: godfreyat@ornl.gov [Oak Ridge National Laboratory, One Bethel Valley Rd., Oak Ridge, TN 37831 (United States)

2016-12-01

A consistent “2D/1D” neutron transport method is derived from the 3D Boltzmann transport equation, to calculate fuel-pin-resolved neutron fluxes for realistic full-core Pressurized Water Reactor (PWR) problems. The 2D/1D method employs the Method of Characteristics to discretize the radial variables and a lower order transport solution to discretize the axial variable. This paper describes the theory of the 2D/1D method and its implementation in the MPACT code, which has become the whole-core deterministic neutron transport solver for the Consortium for Advanced Simulations of Light Water Reactors (CASL) core simulator VERA-CS. Several applications have been performed on both leadership-class and industry-class computing clusters. Results are presented for whole-core solutions of the Watts Bar Nuclear Power Station Unit 1 and compared to both continuous-energy Monte Carlo results and plant data.

Parallelizing an electron transport Monte Carlo simulator (MOCASIN 2.0)

International Nuclear Information System (INIS)

Schwetman, H.; Burdick, S.

1988-01-01

Electron transport simulators are tools for studying electrical properties of semiconducting materials and devices. As demands for modeling more complex devices and new materials have emerged, so have demands for more processing power. This paper documents a project to convert an electron transport simulator (MOCASIN 2.0) to a parallel processing environment. In addition to describing the conversion, the paper presents PPL, a parallel programming version of C running on a Sequent multiprocessor system. In timing tests, models that simulated the movement of 2,000 particles for 100 time steps were executed on ten processors, with a parallel efficiency of over 97%

Simulating the convective precipitation diurnal cycle in a North American scale convection-permitting model

Science.gov (United States)

Scaff, L.; Li, Y.; Prein, A. F.; Liu, C.; Rasmussen, R.; Ikeda, K.

2017-12-01

A better representation of the diurnal cycle of convective precipitation is essential for the analysis of the energy balance and the water budget components such as runoff, evaporation and infiltration. Convection-permitting regional climate modeling (CPM) has been shown to improve the models' performance of summer precipitation, allowing to: (1) simulate the mesoscale processes in more detail and (2) to provide more insights in future changes in convective precipitation under climate change. In this work we investigate the skill of the Weather Research and Forecast model (WRF) in simulating the summer precipitation diurnal cycle over most of North America. We use 4 km horizontal grid spacing in a 13-years long current and future period. The future scenario is assuming no significant changes in large-scale weather patterns and aims to answer how the weather of the current climate would change if it would reoccur at the end of the century under a high-end emission scenario (Pseudo Global Warming). We emphasize on a region centered on the lee side of the Canadian Rocky Mountains, where the summer precipitation amount shows a regional maximum. The historical simulations are capable to correctly represent the diurnal cycle. At the lee-side of the Canadian Rockies the increase in the convective available potential energy as well as pronounced low-level moisture flux from the southeast Prairies explains the local maximum in summer precipitation. The PGW scenario shows an increase in summer precipitation amount and intensity in this region, consistently with a stronger source of moisture and convective energy.

3D numerical simulations of multiphase continental rifting

Science.gov (United States)

Naliboff, J.; Glerum, A.; Brune, S.

2017-12-01

Observations of rifted margin architecture suggest continental breakup occurs through multiple phases of extension with distinct styles of deformation. The initial rifting stages are often characterized by slow extension rates and distributed normal faulting in the upper crust decoupled from deformation in the lower crust and mantle lithosphere. Further rifting marks a transition to higher extension rates and coupling between the crust and mantle lithosphere, with deformation typically focused along large-scale detachment faults. Significantly, recent detailed reconstructions and high-resolution 2D numerical simulations suggest that rather than remaining focused on a single long-lived detachment fault, deformation in this phase may progress toward lithospheric breakup through a complex process of fault interaction and development. The numerical simulations also suggest that an initial phase of distributed normal faulting can play a key role in the development of these complex fault networks and the resulting finite deformation patterns. Motivated by these findings, we will present 3D numerical simulations of continental rifting that examine the role of temporal increases in extension velocity on rifted margin structure. The numerical simulations are developed with the massively parallel finite-element code ASPECT. While originally designed to model mantle convection using advanced solvers and adaptive mesh refinement techniques, ASPECT has been extended to model visco-plastic deformation that combines a Drucker Prager yield criterion with non-linear dislocation and diffusion creep. To promote deformation localization, the internal friction angle and cohesion weaken as a function of accumulated plastic strain. Rather than prescribing a single zone of weakness to initiate deformation, an initial random perturbation of the plastic strain field combined with rapid strain weakening produces distributed normal faulting at relatively slow rates of extension in both 2D and

File list: NoD.Pan.20.AllAg.Pancreas [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Pan.20.AllAg.Pancreas mm9 No description Pancreas Pancreas ERX651337,ERX651340,...ERX651341,ERX651342 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Pan.20.AllAg.Pancreas.bed ...

File list: NoD.Liv.20.AllAg.Hepatocytes [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Liv.20.AllAg.Hepatocytes hg19 No description Liver Hepatocytes SRX815538,SRX477...08749,ERX025732,ERX008736 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Liv.20.AllAg.Hepatocytes.bed ...

File list: NoD.Kid.20.AllAg.Kidney [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Kid.20.AllAg.Kidney mm9 No description Kidney Kidney ERX221027,ERX096865,ERX096...850,ERX221031 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Kid.20.AllAg.Kidney.bed ...

Simulations of drift waves in 3D magnetic configurations

International Nuclear Information System (INIS)

Jost, G.

2000-06-01

Drift waves are commonly held responsible for anomalous transport in tokamak configurations and in particular for the anomalously high heat loss. The next generation of stellarators on the other hand are hoped to be characterized by a much smaller neo-classical transport and by particle confinement close to that of tokamaks. There is nevertheless a strong interest in the stellarator community to study the properties of drift waves in 3D magnetic configurations. To serve this interest we have developed the first global gyrokinetic code, EUTERPE, aimed at the investigation of linear drift wave stability in general toroidal geometry. The physical model assumes electrostatic waves and adiabatic electrons. EUTERPE is a particle-in-cell (PIC) code in which the gyrokinetic Poisson equation is discretized with the finite element method defined in the PEST -1 system of magnetic coordinates. The magnetic geometry is provided by the magnetohydrodynamic (MHD) equilibrium code VMEC. The complete 3D model has been successfully validated in toroidal axisymmetric and straight helical geometries and has permitted the first simulation of unstable global ITG driven modes in non-axisymmetric toroidal configurations. As a first application, two configurations have been studied, the Quasi-Axially symmetric Stellarator with three fields periods (QAS3) currently one system under consideration at the Princeton Plasma Physics Laboratory and the Helically Symmetric experiment (HSX) which has recently started operation at the University of Wisconsin. QAS3 is characterized by a tokamak-Iike field in the outer part of the torus. In this structure the drift waves are mainly affected by the magnetic shear and barely by the shape of the plasma. Also, the results are very close to those obtained for a tokamak. On the other hand, results for the HSX configuration, which is characterized by a dominant helical magnetic field, show a clear 3D effect, namely a strong toroidal variation of the drift wave

File list: NoD.Neu.20.AllAg.Midbrain [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Midbrain mm9 No description Neural Midbrain ERX102458,ERX102459,ER...X102460,ERX102461,SRX002662 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Neu.20.AllAg.Midbrain.bed ...

File list: NoD.Liv.20.AllAg.Hepatocytes [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Liv.20.AllAg.Hepatocytes mm9 No description Liver Hepatocytes ERX113003,SRX1038...,ERX113014,ERX008746,ERX113010,ERX008753 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Liv.20.AllAg.Hepatocytes.bed ...

Statistical 3D damage accumulation model for ion implant simulators

CERN Document Server

Hernandez-Mangas, J M; Enriquez, L E; Bailon, L; Barbolla, J; Jaraiz, M

2003-01-01

A statistical 3D damage accumulation model, based on the modified Kinchin-Pease formula, for ion implant simulation has been included in our physically based ion implantation code. It has only one fitting parameter for electronic stopping and uses 3D electron density distributions for different types of targets including compound semiconductors. Also, a statistical noise reduction mechanism based on the dose division is used. The model has been adapted to be run under parallel execution in order to speed up the calculation in 3D structures. Sequential ion implantation has been modelled including previous damage profiles. It can also simulate the implantation of molecular and cluster projectiles. Comparisons of simulated doping profiles with experimental SIMS profiles are presented. Also comparisons between simulated amorphization and experimental RBS profiles are shown. An analysis of sequential versus parallel processing is provided.

Statistical 3D damage accumulation model for ion implant simulators

International Nuclear Information System (INIS)

Hernandez-Mangas, J.M.; Lazaro, J.; Enriquez, L.; Bailon, L.; Barbolla, J.; Jaraiz, M.

2003-01-01

A statistical 3D damage accumulation model, based on the modified Kinchin-Pease formula, for ion implant simulation has been included in our physically based ion implantation code. It has only one fitting parameter for electronic stopping and uses 3D electron density distributions for different types of targets including compound semiconductors. Also, a statistical noise reduction mechanism based on the dose division is used. The model has been adapted to be run under parallel execution in order to speed up the calculation in 3D structures. Sequential ion implantation has been modelled including previous damage profiles. It can also simulate the implantation of molecular and cluster projectiles. Comparisons of simulated doping profiles with experimental SIMS profiles are presented. Also comparisons between simulated amorphization and experimental RBS profiles are shown. An analysis of sequential versus parallel processing is provided

Towards deconstruction of the type D(2,0) theory

International Nuclear Information System (INIS)

Bourget, Antoine; Rodriguez-Gomez, Diego; Pini, Alessandro

2017-10-01

We propose a four-dimensional supersymmetric theory that deconstructs, in a particular limit, the six-dimensional (2,0) theory of type D k . This 4d theory is defined by a necklace quiver with alternating gauge nodes O(2k) and Sp(k). We test this proposal by comparing the 6d half-BPS index to the Higgs branch Hilbert series of the 4d theory. In the process, we overcome several technical difficulties, such as Hilbert series calculations for non-complete intersections, and the choice of O versus SO gauge groups. Consistently, the result matches the Coulomb branch formula for the mirror theory upon reduction to 3d.

Development of a Closed Loop Simulator for Poloidal Field Control in DIII-D

International Nuclear Information System (INIS)

J.A. Leuer; M.L. Walker; D.A. Humphreys; J.R. Ferron; A. Nerem; B.G. Penaflor

1999-01-01

The design of a model-based simulator of the DIII-D poloidal field system is presented. The simulator is automatically configured to match a particular DIII-D discharge circuit. The simulator can be run in a data input mode, in which prior acquired DIII-D shot data is input to the simulator, or in a stand-alone predictive mode, in which the model operates in closed loop with the plasma control system. The simulator is used to design and validate a multi-input-multi-output controller which has been implemented on DIII-D to control plasma shape. Preliminary experimental controller results are presented

Development of a CT simulator and its current clinical status

International Nuclear Information System (INIS)

Nagata, Yasushi; Hiraoka, Masahiro; Nishidai, Takehiro

2000-01-01

A computed tomography (CT) simulator is defined as a radiotherapy treatment planning (RTP) system which consists of an X-ray CT scanner, a treatment planning computer, and a marking projector. The developmental process from the introduction of an X-ray CT to a CT simulator is described in this article. After the development of the first CT simulator, several new developments in CT scanners, marking projector, and data transfer networks were introduced. CT simulator systems have recently become more widely available and are produced by more than 8 commercial companies. The advantages of a CT simulator are a shortening of overall RTP time, increased accuracy of RTP, and the possibility of 3-D conformal therapy. Clinical experience with CT simulators has accumulated over the past 10 years. Site-specific trials have been undertaken, and the clinical usefulness of CT simulators for breast cancer, maxillary cancer, nasopharyngeal cancer, orbital tumor, lung cancer and other tumors has been demonstrated. The use of CT simulators has resulted in a decrease in the complications of radiotherapy. It also appears to be an essential tool for dose escalation studies, which may permit increased local control of certain tumors. In Japan, CT simulators were in use at more than 134 (20%) of 682 radiotherapy institutions as of the end of 1998. In the USA, CT simulators were present in more than 12% of 1,542 radiotherapy centers in 1994. The CT simulator is now an essential RTP system for advanced radiotherapy. (author)

Simulated radiographic bone and joint modeling from 3D ankle MRI: feasibility and comparison with radiographs and 2D MRI

Energy Technology Data Exchange (ETDEWEB)

Nordeck, Shaun M. [University of Texas Southwestern Medical College, Dallas, TX (United States); University of Texas Southwestern Medical Center, Musculoskeletal Radiology, Dallas, TX (United States); Koerper, Conrad E.; Adler, Aaron [University of Texas Southwestern Medical College, Dallas, TX (United States); Malhotra, Vidur; Xi, Yin [University of Texas Southwestern Medical Center, Musculoskeletal Radiology, Dallas, TX (United States); Liu, George T. [University of Texas Southwestern Medical Center, Orthopaedic Surgery, Dallas, TX (United States); Chhabra, Avneesh [University of Texas Southwestern Medical Center, Musculoskeletal Radiology, Dallas, TX (United States); University of Texas Southwestern Medical Center, Orthopaedic Surgery, Dallas, TX (United States)

2017-05-15

The purpose of this work is to simulate radiographs from isotropic 3D MRI data, compare relationship of angle and joint space measurements on simulated radiographs with corresponding 2D MRIs and real radiographs (XR), and compare measurement times among the three modalities. Twenty-four consecutive ankles were included, eight males and 16 females, with a mean age of 46 years. Segmented joint models simulating radiographs were created from 3D MRI data sets. Three readers independently performed blinded angle and joint space measurements on the models, corresponding 2D MRIs, and XRs at two time points. Linear mixed models and the intraclass correlation coefficient (ICC) was ascertained, with p values less than 0.05 considered significant. Simulated radiograph models were successfully created in all cases. Good agreement (ICC > 0.65) was noted among all readers across all modalities and among most measurements. Absolute measurement values differed between modalities. Measurement time was significantly greater (p < 0.05) on 2D versus simulated radiographs for most measurements and on XR versus simulated radiographs (p < 0.05) for nearly half the measurements. Simulated radiographs can be successfully generated from 3D MRI data; however, measurements differ. Good inter-reader and moderate-to-good intra-reader reliability was observed and measurements obtained on simulated radiograph models took significantly less time compared to measurements with 2D and generally less time than XR. (orig.)

Simulating coronal condensation dynamics in 3D

Science.gov (United States)

Moschou, S. P.; Keppens, R.; Xia, C.; Fang, X.

2015-12-01

We present numerical simulations in 3D settings where coronal rain phenomena take place in a magnetic configuration of a quadrupolar arcade system. Our simulation is a magnetohydrodynamic simulation including anisotropic thermal conduction, optically thin radiative losses, and parametrised heating as main thermodynamical features to construct a realistic arcade configuration from chromospheric to coronal heights. The plasma evaporation from chromospheric and transition region heights eventually causes localised runaway condensation events and we witness the formation of plasma blobs due to thermal instability, that evolve dynamically in the heated arcade part and move gradually downwards due to interchange type dynamics. Unlike earlier 2.5D simulations, in this case there is no large scale prominence formation observed, but a continuous coronal rain develops which shows clear indications of Rayleigh-Taylor or interchange instability, that causes the denser plasma located above the transition region to fall down, as the system moves towards a more stable state. Linear stability analysis is used in the non-linear regime for gaining insight and giving a prediction of the system's evolution. After the plasma blobs descend through interchange, they follow the magnetic field topology more closely in the lower coronal regions, where they are guided by the magnetic dips.

Two-year concurrent observation of isoprene at 20 sites over China: comparison with MEGAN-REAM model simulation

Science.gov (United States)

Zhang, Y.; Yang, W.; Zhang, R.; Zhang, Z.; Lyu, S.; Yu, J.; Wang, Y.; Wang, G.; Wang, X.

2017-12-01

Isoprene, the most abundant non-methane hydrocarbon emitted from plants, directly and indirectly affects atmospheric photochemistry and radiative forcing, yet narrowing its emission uncertainties is a continuous challenge. Comparison of observed and modelled isoprene on large spatiotemporal scales would help recognize factors that control isoprene variability, systematic field observation data are however quite lacking. Here we collected ambient air samples with 1 L silonite-treated stainless steel canisters simultaneously at 20 sites over China on every Wednesday at approximately 14:00 pm Beijing time from 2012 to 2014, and analyzed isoprene mixing ratios by preconcentrator-GC-MSD/FID. Observed isoprene mixing ratios were also compared with that simulated by coupling MEGAN 2.0 (Guenther et al., 2006) with a 3-D Regional chEmical trAnsport Model (REAM) (Zhang et al., 2017). Similar seasonal variations between observation and model simulation were obtained for most of sampling sites, but overall the average isoprene mixing ratios during growing months (May to October) was 0.37 ± 0.08 ppbv from model simulation, about 32% lower than that of 0.54 ± 0.20 ppbv based on ground-based observation, and this discrepancy was particularly significant in north China during wintertime. Further investigation demonstrated that emission of biogenic isoprene in northwest China might be underestimated and non-biogenic emission, such burning biomass/biofuel, might contribute to the elevated levels of isoprene during winter time. The observation-based empirical formulas for changing isoprene emission with solar radiation and temperature were also derived for different regions of China.

Simulation of decay heat removal by natural convection in a pool type fast reactor model-ramona-with coupled 1D/2D thermal hydraulic code system

Energy Technology Data Exchange (ETDEWEB)

Kasinathan, N.; Rajakumar, A.; Vaidyanathan, G.; Chetal, S.C. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

1995-09-01

Post shutdown decay heat removal is an important safety requirement in any nuclear system. In order to improve the reliability of this function, Liquid metal (sodium) cooled fast breeder reactors (LMFBR) are equipped with redundant hot pool dipped immersion coolers connected to natural draught air cooled heat exchangers through intermediate sodium circuits. During decay heat removal, flow through the core, immersion cooler primary side and in the intermediate sodium circuits are also through natural convection. In order to establish the viability and validate computer codes used in making predictions, a 1:20 scale experimental model called RAMONA with water as coolant has been built and experimental simulation of decay heat removal situation has been performed at KfK Karlsruhe. Results of two such experiments have been compiled and published as benchmarks. This paper brings out the results of the numerical simulation of one of the benchmark case through a 1D/2D coupled code system, DHDYN-1D/THYC-2D and the salient features of the comparisons. Brief description of the formulations of the codes are also included.

File list: NoD.Neu.20.AllAg.Brain [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Brain mm9 No description Neural Brain ERX161927,ERX161921,ERX16193...284,ERX402259,ERX402286,ERX402292,ERX402281 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Neu.20.AllAg.Brain.bed ...

File list: NoD.Gon.20.AllAg.Testis [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Gon.20.AllAg.Testis hg19 No description Gonad Testis ERX096851,ERX161924,ERX096...849,ERX096874,ERX096842,ERX096870,ERX096875 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Gon.20.AllAg.Testis.bed ...

20th and 21st Joint Workshop on Sustained Simulation Performance

CERN Document Server

Bez, Wolfgang; Focht, Erich; Kobayashi, Hiroaki; Qi, Jiaxing; Roller, Sabine

2015-01-01

The book presents the state of the art in high-performance computing and simulation on modern supercomputer architectures. It covers trends in hardware and software development in general, and the future of high-performance systems and heterogeneous architectures specifically. The application contributions cover computational fluid dynamics, material science, medical applications and climate research. Innovative fields like coupled multi-physics or multi-scale simulations are also discussed. All papers were chosen from presentations given at the 20th Workshop on Sustained Simulation Performance in December 2014 at the HLRS, University of Stuttgart, Germany, and the subsequent Workshop on Sustained Simulation Performance at Tohoku University in February 2015.  .

APROS 3-D core models for simulators and plant analyzers

International Nuclear Information System (INIS)

Puska, E.K.

1999-01-01

The 3-D core models of APROS simulation environment can be used in simulator and plant analyzer applications, as well as in safety analysis. The key feature of APROS models is that the same physical models can be used in all applications. For three-dimensional reactor cores the APROS models cover both quadratic BWR and PWR cores and the hexagonal lattice VVER-type cores. In APROS environment the user can select the number of flow channels in the core and either five- or six-equation thermal hydraulic model for these channels. The thermal hydraulic model and the channel description have a decisive effect on the calculation time of the 3-D core model and thus just these selection make at present the major difference between a safety analysis model and a training simulator model. The paper presents examples of various types of 3-D LWR-type core descriptions for simulator and plant analyzer use and discusses the differences of calculation speed and physical results between a typical safety analysis model description and a real-time simulator model description in transients. (author)

Numerically robust and efficient nonlocal electron transport in 2D DRACO simulations

Science.gov (United States)

Cao, Duc; Chenhall, Jeff; Moses, Greg; Delettrez, Jacques; Collins, Tim

2013-10-01

An improved implicit algorithm based on Schurtz, Nicolai and Busquet (SNB) algorithm for nonlocal electron transport is presented. Validation with direct drive shock timing experiments and verification with the Goncharov nonlocal model in 1D LILAC simulations demonstrate the viability of this efficient algorithm for producing 2D lagrangian radiation hydrodynamics direct drive simulations. Additionally, simulations provide strong incentive to further modify key parameters within the SNB theory, namely the ``mean free path.'' An example 2D polar drive simulation to study 2D effects of the nonlocal flux as well as mean free path modifications will also be presented. This research was supported by the University of Rochester Laboratory for Laser Energetics.

File list: NoD.Kid.20.AllAg.Kidney [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Kid.20.AllAg.Kidney hg19 No description Kidney Kidney ERX324201,ERX324184,ERX32...4224,ERX096872,ERX324208,ERX221030,ERX096877,ERX221035 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Kid.20.AllAg.Kidney.bed ...

Magnetic flux pumping in 3D nonlinear magnetohydrodynamic simulations

Science.gov (United States)

Krebs, I.; Jardin, S. C.; Günter, S.; Lackner, K.; Hoelzl, M.; Strumberger, E.; Ferraro, N.

2017-10-01

A self-regulating magnetic flux pumping mechanism in tokamaks that maintains the core safety factor at q ≈1 , thus preventing sawteeth, is analyzed in nonlinear 3D magnetohydrodynamic simulations using the M3D-C1 code. In these simulations, the most important mechanism responsible for the flux pumping is that a saturated (m =1 ,n =1 ) quasi-interchange instability generates an effective negative loop voltage in the plasma center via a dynamo effect. It is shown that sawtoothing is prevented in the simulations if β is sufficiently high to provide the necessary drive for the (m =1 ,n =1 ) instability that generates the dynamo loop voltage. The necessary amount of dynamo loop voltage is determined by the tendency of the current density profile to centrally peak which, in our simulations, is controlled by the peakedness of the applied heat source profile.

Implementation of virtual models from sheet metal forming simulation into physical 3D colour models using 3D printing

Science.gov (United States)

Junk, S.

2016-08-01

Today the methods of numerical simulation of sheet metal forming offer a great diversity of possibilities for optimization in product development and in process design. However, the results from simulation are only available as virtual models. Because there are any forming tools available during the early stages of product development, physical models that could serve to represent the virtual results are therefore lacking. Physical 3D-models can be created using 3D-printing and serve as an illustration and present a better understanding of the simulation results. In this way, the results from the simulation can be made more “comprehensible” within a development team. This paper presents the possibilities of 3D-colour printing with particular consideration of the requirements regarding the implementation of sheet metal forming simulation. Using concrete examples of sheet metal forming, the manufacturing of 3D colour models will be expounded upon on the basis of simulation results.

File list: NoD.Dig.20.AllAg.Intestines [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Dig.20.AllAg.Intestines mm9 No description Digestive tract Intestines ERX421334...,ERX421319,ERX421323,ERX421333,ERX421324,ERX421320,ERX421321,ERX421336,ERX421330 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Dig.20.AllAg.Intestines.bed ...

Numerical Simulation of 3D Solid-Liquid Turbulent Flow in a Low Specific Speed Centrifugal Pump: Flow Field Analysis

Directory of Open Access Journals (Sweden)

Baocheng Shi

2014-06-01

Full Text Available For numerically simulating 3D solid-liquid turbulent flow in low specific speed centrifugal pumps, the iteration convergence problem caused by complex internal structure and high rotational speed of pump is always a problem for numeral simulation researchers. To solve this problem, the combination of three measures of dynamic underrelaxation factor adjustment, step method, and rotational velocity control means according to residual curves trends of operating parameters was used to improve the numerical convergence. Numeral simulation of 3D turbulent flow in a low specific speed solid-liquid centrifugal pump was performed, and the results showed that the improved solution strategy is greatly helpful to the numerical convergence. Moreover, the 3D turbulent flow fields in pumps have been simulated for the bottom ash-particles with the volume fraction of 10%, 20%, and 30% at the same particle diameter of 0.1 mm. The two-phase calculation results are compared with those of single-phase clean water flow. The calculated results gave the main region of the abrasion of the impeller and volute casing and improve the hydraulic design of the impeller in order to decrease the abrasion and increase the service life of the pump.

3D Simulation of External Flooding Events for the RISMC Pathway

International Nuclear Information System (INIS)

Prescott, Steven; Mandelli, Diego; Sampath, Ramprasad; Smith, Curtis; Lin, Linyu

2015-01-01

Incorporating 3D simulations as part of the Risk-Informed Safety Margins Characterization (RISMIC) Toolkit allows analysts to obtain a more complete picture of complex system behavior for events including external plant hazards. External events such as flooding have become more important recently – however these can be analyzed with existing and validated simulated physics toolkits. In this report, we describe these approaches specific to flooding-based analysis using an approach called Smoothed Particle Hydrodynamics. The theory, validation, and example applications of the 3D flooding simulation are described. Integrating these 3D simulation methods into computational risk analysis provides a spatial/visual aspect to the design, improves the realism of results, and can prove visual understanding to validate the analysis of flooding.

3D Simulation of External Flooding Events for the RISMC Pathway

Energy Technology Data Exchange (ETDEWEB)

Prescott, Steven [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mandelli, Diego [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sampath, Ramprasad [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis [Idaho National Lab. (INL), Idaho Falls, ID (United States); Lin, Linyu [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-01

Incorporating 3D simulations as part of the Risk-Informed Safety Margins Characterization (RISMIC) Toolkit allows analysts to obtain a more complete picture of complex system behavior for events including external plant hazards. External events such as flooding have become more important recently – however these can be analyzed with existing and validated simulated physics toolkits. In this report, we describe these approaches specific to flooding-based analysis using an approach called Smoothed Particle Hydrodynamics. The theory, validation, and example applications of the 3D flooding simulation are described. Integrating these 3D simulation methods into computational risk analysis provides a spatial/visual aspect to the design, improves the realism of results, and can prove visual understanding to validate the analysis of flooding.

High-resolution 3D simulations of NIF ignition targets performed on Sequoia with HYDRA

Science.gov (United States)

Marinak, M. M.; Clark, D. S.; Jones, O. S.; Kerbel, G. D.; Sepke, S.; Patel, M. V.; Koning, J. M.; Schroeder, C. R.

2015-11-01

Developments in the multiphysics ICF code HYDRA enable it to perform large-scale simulations on the Sequoia machine at LLNL. With an aggregate computing power of 20 Petaflops, Sequoia offers an unprecedented capability to resolve the physical processes in NIF ignition targets for a more complete, consistent treatment of the sources of asymmetry. We describe modifications to HYDRA that enable it to scale to over one million processes on Sequoia. These include new options for replicating parts of the mesh over a subset of the processes, to avoid strong scaling limits. We consider results from a 3D full ignition capsule-only simulation performed using over one billion zones run on 262,000 processors which resolves surface perturbations through modes l = 200. We also report progress towards a high-resolution 3D integrated hohlraum simulation performed using 262,000 processors which resolves surface perturbations on the ignition capsule through modes l = 70. These aim for the most complete calculations yet of the interactions and overall impact of the various sources of asymmetry for NIF ignition targets. This work was performed under the auspices of the Lawrence Livermore National Security, LLC, (LLNS) under Contract No. DE-AC52-07NA27344.

File list: NoD.Oth.20.AllAg.Olfactory_epithelium [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Oth.20.AllAg.Olfactory_epithelium mm9 No description Others Olfactory epithelium... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Oth.20.AllAg.Olfactory_epithelium.bed ...

File list: NoD.Adl.20.AllAg.Octopaminergic_neurons [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Adl.20.AllAg.Octopaminergic_neurons dm3 No description Adult Octopaminergic neurons... http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/NoD.Adl.20.AllAg.Octopaminergic_neurons.bed ...

File list: NoD.CDV.20.AllAg.Atrioventicular_canals [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.CDV.20.AllAg.Atrioventicular_canals mm9 No description Cardiovascular Atrioventicular canals... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.CDV.20.AllAg.Atrioventicular_canals.bed ...

The efficiency and equity of marketable permits for CO2 emissions

International Nuclear Information System (INIS)

Rose, A.; Stevens, B.

1993-01-01

This paper examines the efficiency and equity implications of alternative assignments of marketable permits for carbon dioxide. A non-linear programming model is used to estimate the net welfare changes of permit allocations based on Sovereignty and Rawlsian equity criteria for 8 countries/regions covering the spectrum of economic development levels. The net welfare gains associated with an overall 20% reduction in CO 2 emissions are estimated to be nearly 20 billion dollars, an increase of several billion dollars over a system of inflexible emission quotas requiring 20% abatement in each country. Also, although the welfare changes implied by alternative permit assignments may vary greatly between countries before trading, the trading process significantly reduces the disparities. This result stems from the Coase Theorem, which implies a uniquely efficient outcome. That is, individual country abatement levels and, hence, costs, are the same under all permit assignments after trading, and net welfare for a given nation differs only by the amount of permit revenues/expenditures associated with the application of alternative equity criteria. Foremost among the paper's policy implications is that although equity criteria may differ significantly in principle, their welfare implications in practice may be very similar for various subsets of these criteria. This should reduce tensions at the bargaining table and facilitate the negotiation of greenhouse gas agreements. 52 refs., 3 figs., 8 tabs

Efficient performance simulation of class D amplifier output stages

DEFF Research Database (Denmark)

Nyboe, Flemming; Risbo, Lars; Andreani, Pietro

2005-01-01

Straightforward simulation of amplifier distortion involves transient simulation of operation on a sine wave input signal, and a subsequent FFT of the output voltage. This approach is very slow on class D amplifiers, since the switching behavior forces simulation time steps that are many orders...... of magnitude smaller than the duration of one period of an audio sine wave. This work presents a method of simulating the amplifier transfer characteristic using a minimum amount of simulation time, and then deriving THD from the results....

File list: NoD.Kid.20.AllAg.Nephrectomy_sample [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Kid.20.AllAg.Nephrectomy_sample hg19 No description Kidney Nephrectomy sample h...ttp://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Kid.20.AllAg.Nephrectomy_sample.bed ...

File list: NoD.CDV.20.AllAg.Carotid_Arteries [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.CDV.20.AllAg.Carotid_Arteries hg19 No description Cardiovascular Carotid Arteri...es http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.CDV.20.AllAg.Carotid_Arteries.bed ...

File list: NoD.Emb.20.AllAg.Embryonic_pancreas [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Emb.20.AllAg.Embryonic_pancreas mm9 No description Embryo Embryonic pancreas ht...tp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Emb.20.AllAg.Embryonic_pancreas.bed ...

Structure Prediction, Molecular Dynamics Simulation and Docking Studies of D-Specific Dehalogenase from Rhizobium sp. RC1

Directory of Open Access Journals (Sweden)

Ismaila Yada Sudi

2012-11-01

Full Text Available Currently, there is no three-dimensional structure of D-specific dehalogenase (DehD in the protein database. We modeled DehD using ab initio technique, performed molecular dynamics (MD simulation and docking of D-2-chloropropionate (D-2CP, D-2-bromopropionate (D-2BP, monochloroacetate (MCA, monobromoacetate (MBA, 2,2-dichloropropionate (2,2-DCP, d,l-2,3-dichloropropionate (d,l-2,3-DCP, and 3-chloropropionate (3-CP into the DehD active site. The sequences of DehD and D-2-haloacid dehalogenase (HadD from Pseudomonas putida AJ1 have 15% sequence similarity. The model had 80% of the amino acid residues in the most favored region when compared to the crystal structure of DehI from Pseudomonas putida PP3. Docking analysis revealed that Arg107, Arg134 and Tyr135 interacted with D-2CP, and Glu20 activated the water molecule for hydrolytic dehalogenation. Single residue substitutions at 25–30 °C showed that polar residues of DehD were stable when substituted with nonpolar residues and showed a decrease in activity within the same temperature range. The molecular dynamics simulation of DehD and its variants showed that in R134A variant, Arg107 interacted with D-2CP, while in Y135A, Gln221 and Arg231 interacted with D-2CP. It is our emphatic belief that the new model will be useful for the rational design of DehDs with enhanced potentials.

File list: NoD.Dig.20.AllAg.Intestinal_crypt [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Dig.20.AllAg.Intestinal_crypt mm9 No description Digestive tract Intestinal cry...pt http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Dig.20.AllAg.Intestinal_crypt.bed ...

DEVELOPMENT OF A VIRTUAL 3D-SIMULATOR OF THE FEED PELLETING TECHNOLOGICAL PROCESS

Directory of Open Access Journals (Sweden)

N. Shcherbakov

2017-08-01

Full Text Available The process of developing a virtual 3D simulator of the process of granulation of mixed fodders is considered. The consequences of errors in the operation of press granulator operators are considered. The difficulties associated with the training of high-tech and expensive equipment operators are described. The necessity and described difficulties of acquiring practical skills of working with such equipment at the training stage are substantiated. It is argued the need to introduce computer simulators in educational institutions in order to improve the quality of the acquired knowledge, form a complex decision-making skill for future operators of technological processes. The results of a survey on improving the efficiency of management of technological processes after the introduction of simulators at enterprises are considered. The data of the simulator market and its forecasts for 2017 by regions and types of the interface used are presented. The conclusion is drawn about the growing popularity of simulators based on the 3D interface. The advantage of using the 3D interface with respect to the 2D interface is substantiated. The types of immersion in the learning environment in various simulator interfaces are considered. The vulnerabilities of the 3D simulator are noted. The goal is to develop a 3D simulator for a press granulator operator. A solution of a set of tasks is proposed to achieve this goal. The plan for creating a simulator was developed. A detailed consideration of the development stages of the simulator is given. The possibilities of using the simulator being developed are considered. The possibility of developing a simulator of emergency situations is described. The relevance of this development is justified.

Amyotrophic Lateral Sclerosis Type 20 - In Silico Analysis and Molecular Dynamics Simulation of hnRNPA1.

Directory of Open Access Journals (Sweden)

Bruna Baumgarten Krebs

Full Text Available Amyotrophic Lateral Sclerosis (ALS is a fatal neurodegenerative disease that affects the upper and lower motor neurons. 5-10% of cases are genetically inherited, including ALS type 20, which is caused by mutations in the hnRNPA1 gene. The goals of this work are to analyze the effects of non-synonymous single nucleotide polymorphisms (nsSNPs on hnRNPA1 protein function, to model the complete tridimensional structure of the protein using computational methods and to assess structural and functional differences between the wild type and its variants through Molecular Dynamics simulations. nsSNP, PhD-SNP, Polyphen2, SIFT, SNAP, SNPs&GO, SNPeffect and PROVEAN were used to predict the functional effects of nsSNPs. Ab initio modeling of hnRNPA1 was made using Rosetta and refined using KoBaMIN. The structure was validated by PROCHECK, Rampage, ERRAT, Verify3D, ProSA and Qmean. TM-align was used for the structural alignment. FoldIndex, DICHOT, ELM, D2P2, Disopred and DisEMBL were used to predict disordered regions within the protein. Amino acid conservation analysis was assessed by Consurf, and the molecular dynamics simulations were performed using GROMACS. Mutations D314V and D314N were predicted to increase amyloid propensity, and predicted as deleterious by at least three algorithms, while mutation N73S was predicted as neutral by all the algorithms. D314N and D314V occur in a highly conserved amino acid. The Molecular Dynamics results indicate that all mutations increase protein stability when compared to the wild type. Mutants D314N and N319S showed higher overall dimensions and accessible surface when compared to the wild type. The flexibility level of the C-terminal residues of hnRNPA1 is affected by all mutations, which may affect protein function, especially regarding the protein ability to interact with other proteins.

File list: NoD.Bld.20.AllAg.PBMC [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Bld.20.AllAg.PBMC hg19 No description Blood PBMC SRX833337,SRX833329,SRX833330,...SRX833332,SRX833333,SRX833331,SRX833334,SRX833335,SRX833336,SRX833340,SRX833339,SRX833338 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Bld.20.AllAg.PBMC.bed ...

File list: Oth.NoD.20.Epitope_tags.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.NoD.20.Epitope_tags.AllCell hg19 TFs and others Epitope tags No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Oth.NoD.20.Epitope_tags.AllCell.bed ...

File list: NoD.PSC.20.AllAg.Embryoid_Bodies [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.Embryoid_Bodies mm9 No description Pluripotent stem cell Embryoid Bodie...s http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.PSC.20.AllAg.Embryoid_Bodies.bed ...

File list: NoD.CDV.20.AllAg.Endocardial_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.CDV.20.AllAg.Endocardial_cells hg19 No description Cardiovascular Endocardial c...ells DRX014674 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.CDV.20.AllAg.Endocardial_cells.bed ...

File list: NoD.Adp.20.AllAg.Adipose_Tissue [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Adp.20.AllAg.Adipose_Tissue hg19 No description Adipocyte Adipose Tissue SRX134...732 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Adp.20.AllAg.Adipose_Tissue.bed ...

76 FR 8374 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2011-02-14

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2011-N021; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

76 FR 33334 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2011-06-08

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2011-N112; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

75 FR 52012 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2010-08-24

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2010-N181; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

75 FR 5101 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2010-02-01

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2010-N010; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

76 FR 18576 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2011-04-04

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2011-N056; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

76 FR 10063 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2011-02-23

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2011-N026; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

75 FR 27361 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2010-05-14

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2010-N095; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of applications to...

File list: Oth.NoD.20.Epitope_tags.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.NoD.20.Epitope_tags.AllCell sacCer3 TFs and others Epitope tags No description ...http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/Oth.NoD.20.Epitope_tags.AllCell.bed ...

File list: NoD.Myo.20.AllAg.Fetal_muscle [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Myo.20.AllAg.Fetal_muscle hg19 No description Muscle Fetal muscle SRX300958,SRX...RX213502 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Myo.20.AllAg.Fetal_muscle.bed ...

File list: NoD.Neu.20.AllAg.Adult_brains [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Adult_brains hg19 No description Neural Adult brains ERX161917,SRX...019404 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Neu.20.AllAg.Adult_brains.bed ...

File list: NoD.Emb.20.AllAg.Embryonic_trunk [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Emb.20.AllAg.Embryonic_trunk mm9 No description Embryo Embryonic trunk ERX40226...7,ERX402264 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Emb.20.AllAg.Embryonic_trunk.bed ...

3D simulation of CANDU reactor regulating system

International Nuclear Information System (INIS)

Venescu, B.; Zevedei, D.; Jurian, M.

2013-01-01

Present paper shows the evaluation of the performance of the 3-D modal synthesis based reactor kinetic model in a closed-loop environment in a MATLAB/SIMULINK based Reactor Regulating System (RRS) simulation platform. A notable advantage of the 3-D model is the level of details that it can reveal as compared to the coupled point kinetic model. Using the developed RRS simulation platform, the reactor internal behaviours can be revealed during load-following tests. The test results are also benchmarked against measurements from an existing (CANDU) power plant. It can be concluded that the 3-D reactor model produces more realistic view of the core neutron flux distribution, which is closer to the real plant measurements than that from a coupled point kinetic model. It is also shown that, through a vectorization process, the computational load of the 3-D model is comparable with that of the 14-zone coupled point kinetic model. Furthermore, the developed Graphical User Interface (GUI) software package for RRS implementation represents a user friendly and independent application environment for education training and industrial utilizations. (authors)

Investigation of tropical diurnal convection biases in a climate model using TWP-ICE observations and convection-permitting simulations

Science.gov (United States)

Lin, W.; Xie, S.; Jackson, R. C.; Endo, S.; Vogelmann, A. M.; Collis, S. M.; Golaz, J. C.

2017-12-01

Climate models are known to have difficulty in simulating tropical diurnal convections that exhibit distinct characteristics over land and open ocean. While the causes are rooted in deficiencies in convective parameterization in general, lack of representations of mesoscale dynamics in terms of land-sea breeze, convective organization, and propagation of convection-induced gravity waves also play critical roles. In this study, the problem is investigated at the process-level with the U.S. Department of Energy Accelerated Climate Modeling for Energy (ACME) model in short-term hindcast mode using the Cloud Associated Parameterization Testbed (CAPT) framework. Convective-scale radar retrievals and observation-driven convection-permitting simulations for the Tropical Warm Pool-International Cloud Experiment (TWP-ICE) cases are used to guide the analysis of the underlying processes. The emphasis will be on linking deficiencies in representation of detailed process elements to the model biases in diurnal convective properties and their contrast among inland, coastal and open ocean conditions.

Development of computational science in JAEA. R and D of simulation

International Nuclear Information System (INIS)

Nakajima, Norihiro; Araya, Fumimasa; Hirayama, Toshio

2006-01-01

R and D of computational science in JAEA (Japan Atomic Energy Agency) is described. Environment of computer, R and D system in CCSE (Center for Computational Science and e-Systems), joint computational science researches in Japan and world, development of computer technologies, the some examples of simulation researches, 3-dimensional image vibrational platform system, simulation researches of FBR cycle techniques, simulation of large scale thermal stress for development of steam generator, simulation research of fusion energy techniques, development of grid computing technology, simulation research of quantum beam techniques and biological molecule simulation researches are explained. Organization of JAEA, development of computational science in JAEA, network of JAEA, international collaboration of computational science, and environment of ITBL (Information-Technology Based Laboratory) project are illustrated. (S.Y.)

Comparison of 3D Echocardiogram-Derived 3D Printed Valve Models to Molded Models for Simulated Repair of Pediatric Atrioventricular Valves.

Science.gov (United States)

Scanlan, Adam B; Nguyen, Alex V; Ilina, Anna; Lasso, Andras; Cripe, Linnea; Jegatheeswaran, Anusha; Silvestro, Elizabeth; McGowan, Francis X; Mascio, Christopher E; Fuller, Stephanie; Spray, Thomas L; Cohen, Meryl S; Fichtinger, Gabor; Jolley, Matthew A

2018-03-01

Mastering the technical skills required to perform pediatric cardiac valve surgery is challenging in part due to limited opportunity for practice. Transformation of 3D echocardiographic (echo) images of congenitally abnormal heart valves to realistic physical models could allow patient-specific simulation of surgical valve repair. We compared materials, processes, and costs for 3D printing and molding of patient-specific models for visualization and surgical simulation of congenitally abnormal heart valves. Pediatric atrioventricular valves (mitral, tricuspid, and common atrioventricular valve) were modeled from transthoracic 3D echo images using semi-automated methods implemented as custom modules in 3D Slicer. Valve models were then both 3D printed in soft materials and molded in silicone using 3D printed "negative" molds. Using pre-defined assessment criteria, valve models were evaluated by congenital cardiac surgeons to determine suitability for simulation. Surgeon assessment indicated that the molded valves had superior material properties for the purposes of simulation compared to directly printed valves (p 3D echo-derived molded valves are a step toward realistic simulation of complex valve repairs but require more time and labor to create than directly printed models. Patient-specific simulation of valve repair in children using such models may be useful for surgical training and simulation of complex congenital cases.

Bias-Exchange Metadynamics Simulation of Membrane Permeation of 20 Amino Acids.

Science.gov (United States)

Cao, Zanxia; Bian, Yunqiang; Hu, Guodong; Zhao, Liling; Kong, Zhenzhen; Yang, Yuedong; Wang, Jihua; Zhou, Yaoqi

2018-03-16

Thermodynamics of the permeation of amino acids from water to lipid bilayers is an important first step for understanding the mechanism of cell-permeating peptides and the thermodynamics of membrane protein structure and stability. In this work, we employed bias-exchange metadynamics simulations to simulate the membrane permeation of all 20 amino acids from water to the center of a dipalmitoylphosphatidylcholine (DPPC) membrane (consists of 256 lipids) by using both directional and torsion angles for conformational sampling. The overall accuracy for the free energy profiles obtained is supported by significant correlation coefficients (correlation coefficient at 0.5-0.6) between our results and previous experimental or computational studies. The free energy profiles indicated that (1) polar amino acids have larger free energy barriers than nonpolar amino acids; (2) negatively charged amino acids are the most difficult to enter into the membrane; and (3) conformational transitions for many amino acids during membrane crossing is the key for reduced free energy barriers. These results represent the first set of simulated free energy profiles of membrane crossing for all 20 amino acids.

Bias-Exchange Metadynamics Simulation of Membrane Permeation of 20 Amino Acids

Directory of Open Access Journals (Sweden)

Zanxia Cao

2018-03-01

Full Text Available Thermodynamics of the permeation of amino acids from water to lipid bilayers is an important first step for understanding the mechanism of cell-permeating peptides and the thermodynamics of membrane protein structure and stability. In this work, we employed bias-exchange metadynamics simulations to simulate the membrane permeation of all 20 amino acids from water to the center of a dipalmitoylphosphatidylcholine (DPPC membrane (consists of 256 lipids by using both directional and torsion angles for conformational sampling. The overall accuracy for the free energy profiles obtained is supported by significant correlation coefficients (correlation coefficient at 0.5–0.6 between our results and previous experimental or computational studies. The free energy profiles indicated that (1 polar amino acids have larger free energy barriers than nonpolar amino acids; (2 negatively charged amino acids are the most difficult to enter into the membrane; and (3 conformational transitions for many amino acids during membrane crossing is the key for reduced free energy barriers. These results represent the first set of simulated free energy profiles of membrane crossing for all 20 amino acids.

File list: NoD.Emb.20.AllAg.Embryonic_heart [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Emb.20.AllAg.Embryonic_heart mm9 No description Embryo Embryonic heart SRX11004...02,SRX1100404,SRX1100405 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Emb.20.AllAg.Embryonic_heart.bed ...

4D Simulation for Nuclear Power Plant Construction

International Nuclear Information System (INIS)

Jeong, Seo G.; Suh, Kune Y.

2006-01-01

For the timely and competitive response to rapidly changing energy environment at the turn of millennium, there is a desperate need to build the nuclear power plant (NPP) in the virtual reality of digital engineering prior to commissioning. To construct a NPP is a highly integrated, voluminous project. Verification of design and initial planning is prerequisite to construction to confirm optimal fabrication and high productivity. This paper presents the design feasibility by simulating the initial construction plan of NPP using four-dimensional (4D) simulation. The virtual reality method, using three dimensional (3D) computer-aided design (CAD) model, enables various designs in the project launching stage to be promptly and exactly previewed

75 FR 45650 - Endangered and Threatened Wildlife and Plants; Permits

Science.gov (United States)

2010-08-03

... DEPARTMENT OF THE INTERIOR Fish and Wildlife Service [FWS-R6-ES-2010-N149; 60120-1113-0000-D2] Endangered and Threatened Wildlife and Plants; Permits AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of receipt of applications for permits. SUMMARY: We announce our receipt of an application to...

Simulation of mirror surfaces for virtual estimation of visibility lines for 3D motor vehicle collision reconstruction.

Science.gov (United States)

Leipner, Anja; Dobler, Erika; Braun, Marcel; Sieberth, Till; Ebert, Lars

2017-10-01

3D reconstructions of motor vehicle collisions are used to identify the causes of these events and to identify potential violations of traffic regulations. Thus far, the reconstruction of mirrors has been a problem since they are often based on approximations or inaccurate data. Our aim with this paper was to confirm that structured light scans of a mirror improve the accuracy of simulating the field of view of mirrors. We analyzed the performances of virtual mirror surfaces based on structured light scans using real mirror surfaces and their reflections as references. We used an ATOS GOM III scanner to scan the mirrors and processed the 3D data using Geomagic Wrap. For scene reconstruction and to generate virtual images, we used 3ds Max. We compared the simulated virtual images and photographs of real scenes using Adobe Photoshop. Our results showed that we achieved clear and even mirror results and that the mirrors behaved as expected. The greatest measured deviation between an original photo and the corresponding virtual image was 20 pixels in the transverse direction for an image width of 4256 pixels. We discussed the influences of data processing and alignment of the 3D models on the results. The study was limited to a distance of 1.6m, and the method was not able to simulate an interior mirror. In conclusion, structured light scans of mirror surfaces can be used to simulate virtual mirror surfaces with regard to 3D motor vehicle collision reconstruction. Copyright © 2017 Elsevier B.V. All rights reserved.

77 FR 23803 - Office of Hazardous Materials Safety; Actions on Special Permit Applications

Science.gov (United States)

2012-04-20

...-M......... Conference of 49 CFR To modify the Radiation 172.203(d); special permit add Control Part............ Conference of 49 CFR Part To modify the Radiation 172, Subparts, special permit add Control C, D, E, F, G, 49...; additional mode of Berlin 173.345; transportation Packaging 173.346; (cargo vessel). (Former 173.359; Grantee...

[Non-biological 3D printed simulator for training in percutaneous nephro- lithotripsy].

Science.gov (United States)

Alyaev, Yu G; Sirota, E S; Bezrukov, E A; Ali, S Kh; Bukatov, M D; Letunovskiy, A V; Byadretdinov, I Sh

2018-03-01

To develop a non-biological 3D printed simulator for training and preoperative planning in percutaneous nephrolithotripsy (PCNL), which allows doctors to master and perform all stages of the operation under ultrasound and fluoroscopy guidance. The 3D model was constructed using multislice spiral computed tomography (MSCT) images of a patient with staghorn urolithiasis. The MSCT data were processed and used to print the model. The simulator consisted of two parts: a non-biological 3D printed soft model of a kidney with reproduced intra-renal vascular and collecting systems and a printed 3D model of a human body. Using this 3D printed simulator, PCNL was performed in the interventional radiology operating room under ultrasound and fluoroscopy guidance. The designed 3D printed model of the kidney completely reproduces the individual features of the intra-renal structures of the particular patient. During the training, all the main stages of PCNL were performed successfully: the puncture, dilation of the nephrostomy tract, endoscopic examination, intra-renal lithotripsy. Our proprietary 3D-printed simulator is a promising development in the field of endourologic training and preoperative planning in the treatment of complicated forms of urolithiasis.

File list: NoD.Bld.20.AllAg.Polymorphonuclear_leukocytes [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Bld.20.AllAg.Polymorphonuclear_leukocytes hg19 No description Blood Polymorphonuclear... leukocytes SRX1016682,SRX1016679,SRX1016680,SRX1016681 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Bld.20.AllAg.Polymorphonuclear_leukocytes.bed ...

3D simulation studies of tokamak plasmas using MHD and extended-MHD models

International Nuclear Information System (INIS)

Park, W.; Chang, Z.; Fredrickson, E.; Fu, G.Y.

1996-01-01

The M3D (Multi-level 3D) tokamak simulation project aims at the simulation of tokamak plasmas using a multi-level tokamak code package. Several current applications using MHD and Extended-MHD models are presented; high-β disruption studies in reversed shear plasmas using the MHD level MH3D code, ω *i stabilization and nonlinear island saturation of TAE mode using the hybrid particle/MHD level MH3D-K code, and unstructured mesh MH3D ++ code studies. In particular, three internal mode disruption mechanisms are identified from simulation results which agree which agree well with experimental data

Quantum simulation of 2D topological physics in a 1D array of optical cavities.

Science.gov (United States)

Luo, Xi-Wang; Zhou, Xingxiang; Li, Chuan-Feng; Xu, Jin-Shi; Guo, Guang-Can; Zhou, Zheng-Wei

2015-07-06

Orbital angular momentum of light is a fundamental optical degree of freedom characterized by unlimited number of available angular momentum states. Although this unique property has proved invaluable in diverse recent studies ranging from optical communication to quantum information, it has not been considered useful or even relevant for simulating nontrivial physics problems such as topological phenomena. Contrary to this misconception, we demonstrate the incredible value of orbital angular momentum of light for quantum simulation by showing theoretically how it allows to study a variety of important 2D topological physics in a 1D array of optical cavities. This application for orbital angular momentum of light not only reduces required physical resources but also increases feasible scale of simulation, and thus makes it possible to investigate important topics such as edge-state transport and topological phase transition in a small simulator ready for immediate experimental exploration.

3D hydrodynamic simulations of carbon burning in massive stars

Science.gov (United States)

Cristini, A.; Meakin, C.; Hirschi, R.; Arnett, D.; Georgy, C.; Viallet, M.; Walkington, I.

2017-10-01

We present the first detailed 3D hydrodynamic implicit large eddy simulations of turbulent convection of carbon burning in massive stars. Simulations begin with radial profiles mapped from a carbon-burning shell within a 15 M⊙ 1D stellar evolution model. We consider models with 1283, 2563, 5123, and 10243 zones. The turbulent flow properties of these carbon-burning simulations are very similar to the oxygen-burning case. We performed a mean field analysis of the kinetic energy budgets within the Reynolds-averaged Navier-Stokes framework. For the upper convective boundary region, we find that the numerical dissipation is insensitive to resolution for linear mesh resolutions above 512 grid points. For the stiffer, more stratified lower boundary, our highest resolution model still shows signs of decreasing sub-grid dissipation suggesting it is not yet numerically converged. We find that the widths of the upper and lower boundaries are roughly 30 per cent and 10 per cent of the local pressure scaleheights, respectively. The shape of the boundaries is significantly different from those used in stellar evolution models. As in past oxygen-shell-burning simulations, we observe entrainment at both boundaries in our carbon-shell-burning simulations. In the large Péclet number regime found in the advanced phases, the entrainment rate is roughly inversely proportional to the bulk Richardson number, RiB (∝RiB-α, 0.5 ≲ α ≲ 1.0). We thus suggest the use of RiB as a means to take into account the results of 3D hydrodynamics simulations in new 1D prescriptions of convective boundary mixing.

Fast 2D fluid-analytical simulation of ion energy distributions and electromagnetic effects in multi-frequency capacitive discharges

Science.gov (United States)

Kawamura, E.; Lieberman, M. A.; Graves, D. B.

2014-12-01

A fast 2D axisymmetric fluid-analytical plasma reactor model using the finite elements simulation tool COMSOL is interfaced with a 1D particle-in-cell (PIC) code to study ion energy distributions (IEDs) in multi-frequency capacitive argon discharges. A bulk fluid plasma model, which solves the time-dependent plasma fluid equations for the ion continuity and electron energy balance, is coupled with an analytical sheath model, which solves for the sheath parameters. The time-independent Helmholtz equation is used to solve for the fields and a gas flow model solves for the steady-state pressure, temperature and velocity of the neutrals. The results of the fluid-analytical model are used as inputs to a PIC simulation of the sheath region of the discharge to obtain the IEDs at the target electrode. Each 2D fluid-analytical-PIC simulation on a moderate 2.2 GHz CPU workstation with 8 GB of memory took about 15-20 min. The multi-frequency 2D fluid-analytical model was compared to 1D PIC simulations of a symmetric parallel-plate discharge, showing good agreement. We also conducted fluid-analytical simulations of a multi-frequency argon capacitively coupled plasma (CCP) with a typical asymmetric reactor geometry at 2/60/162 MHz. The low frequency 2 MHz power controlled the sheath width and sheath voltage while the high frequencies controlled the plasma production. A standing wave was observable at the highest frequency of 162 MHz. We noticed that adding 2 MHz power to a 60 MHz discharge or 162 MHz to a dual frequency 2 MHz/60 MHz discharge can enhance the plasma uniformity. We found that multiple frequencies were not only useful for controlling IEDs but also plasma uniformity in CCP reactors.

A global simulation of ICRF heating in a 3D magnetic configuration

International Nuclear Information System (INIS)

Murakami, S.; Fukuyama, A.; Akutsu, T.

2005-01-01

A global simulation code for the ICRF heating analysis in a three-dimensional (3D) magnetic configuration is developed combining two global simulation codes; a drift kinetic equation solver, GNET, and a wave field solver, TASK/WM. Both codes take into account 3D geometry using the numerically obtained 3D MHD equilibrium. The developed simulation code is applied to the LHD configuration as an example. Characteristics of energetic ion distributions in the phase space are clarified in LHD. The simulation results are also compared with experimental results by evaluating the count number of the neutral particle analyzer using the obtained energetic ion distribution, and a relatively good agreement is obtained. (author)

Earthquake cycle simulations with rate-and-state friction and power-law viscoelasticity

Science.gov (United States)

Allison, Kali L.; Dunham, Eric M.

2018-05-01

We simulate earthquake cycles with rate-and-state fault friction and off-fault power-law viscoelasticity for the classic 2D antiplane shear problem of a vertical, strike-slip plate boundary fault. We investigate the interaction between fault slip and bulk viscous flow with experimentally-based flow laws for quartz-diorite and olivine for the crust and mantle, respectively. Simulations using three linear geotherms (dT/dz = 20, 25, and 30 K/km) produce different deformation styles at depth, ranging from significant interseismic fault creep to purely bulk viscous flow. However, they have almost identical earthquake recurrence interval, nucleation depth, and down-dip coseismic slip limit. Despite these similarities, variations in the predicted surface deformation might permit discrimination of the deformation mechanism using geodetic observations. Additionally, in the 25 and 30 K/km simulations, the crust drags the mantle; the 20 K/km simulation also predicts this, except within 10 km of the fault where the reverse occurs. However, basal tractions play a minor role in the overall force balance of the lithosphere, at least for the flow laws used in our study. Therefore, the depth-integrated stress on the fault is balanced primarily by shear stress on vertical, fault-parallel planes. Because strain rates are higher directly below the fault than far from it, stresses are also higher. Thus, the upper crust far from the fault bears a substantial part of the tectonic load, resulting in unrealistically high stresses. In the real Earth, this might lead to distributed plastic deformation or formation of subparallel faults. Alternatively, fault pore pressures in excess of hydrostatic and/or weakening mechanisms such as grain size reduction and thermo-mechanical coupling could lower the strength of the ductile fault root in the lower crust and, concomitantly, off-fault upper crustal stresses.

THREE-DIMENSIONAL CORE-COLLAPSE SUPERNOVA SIMULATED USING A 15 M{sub ⊙} PROGENITOR

Energy Technology Data Exchange (ETDEWEB)

Lentz, Eric J.; Mezzacappa, Anthony; Harris, J. Austin; Yakunin, Konstantin N. [Department of Physics and Astronomy, University of Tennessee, Knoxville, TN 37996-1200 (United States); Bruenn, Stephen W. [Department of Physics, Florida Atlantic University, 777 Glades Road, Boca Raton, FL 33431-0991 (United States); Hix, W. Raphael [Physics Division, Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6354 (United States); Messer, O. E. Bronson [National Center for Computational Sciences, Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6164 (United States); Endeve, Eirik [Computer Science and Mathematics Division, Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6164 (United States); Blondin, John M. [Department of Physics, North Carolina State University, Raleigh, NC 27695-8202 (United States); Marronetti, Pedro, E-mail: elentz@utk.edu [Physics Division, National Science Foundation, Arlington, VA 22207 (United States)

2015-07-10

We have performed ab initio neutrino radiation hydrodynamics simulations in three and two spatial dimensions (3D and 2D) of core-collapse supernovae from the same 15 M{sub ☉} progenitor through 440 ms after core bounce. Both 3D and 2D models achieve explosions; however, the onset of explosion (shock revival) is delayed by ∼100 ms in 3D relative to the 2D counterpart and the growth of the diagnostic explosion energy is slower. This is consistent with previously reported 3D simulations utilizing iron-core progenitors with dense mantles. In the ∼100 ms before the onset of explosion, diagnostics of neutrino heating and turbulent kinetic energy favor earlier explosion in 2D. During the delay, the angular scale of convective plumes reaching the shock surface grows and explosion in 3D is ultimately lead by a single, large-angle plume, giving the expanding shock a directional orientation not dissimilar from those imposed by axial symmetry in 2D simulations. We posit that shock revival and explosion in the 3D simulation may be delayed until sufficiently large plumes form, whereas such plumes form more rapidly in 2D, permitting earlier explosions.

Differences in 3D vs. 2D analysis in lumbar spinal fusion simulations.

Science.gov (United States)

Hsu, Hung-Wei; Bashkuev, Maxim; Pumberger, Matthias; Schmidt, Hendrik

2018-04-27

Lumbar interbody fusion is currently the gold standard in treating patients with disc degeneration or segmental instability. Despite it having been used for several decades, the non-union rate remains high. A failed fusion is frequently attributed to an inadequate mechanical environment after instrumentation. Finite element (FE) models can provide insights into the mechanics of the fusion process. Previous fusion simulations using FE models showed that the geometries and material of the cage can greatly influence the fusion outcome. However, these studies used axisymmetric models which lacked realistic spinal geometries. Therefore, different modeling approaches were evaluated to understand the bone-formation process. Three FE models of the lumbar motion segment (L4-L5) were developed: 2D, Sym-3D and Nonsym-3D. The fusion process based on existing mechano-regulation algorithms using the FE simulations to evaluate the mechanical environment was then integrated into these models. In addition, the influence of different lordotic angles (5, 10 and 15°) was investigated. The volume of newly formed bone, the axial stiffness of the whole segment and bone distribution inside and surrounding the cage were evaluated. In contrast to the Nonsym-3D, the 2D and Sym-3D models predicted excessive bone formation prior to bridging (peak values with 36 and 9% higher than in equilibrium, respectively). The 3D models predicted a more uniform bone distribution compared to the 2D model. The current results demonstrate the crucial role of the realistic 3D geometry of the lumbar motion segment in predicting bone formation after lumbar spinal fusion. Copyright © 2018 Elsevier Ltd. All rights reserved.

3D simulation studies of tokamak plasmas using MHD and extended-MHD models

International Nuclear Information System (INIS)

Park, W.; Chang, Z.; Fredrickson, E.; Fu, G.Y.; Pomphrey, N.; Sugiyama, L.E.

1997-01-01

The M3D (Multi-level 3D) tokamak simulation project aims at the simulation of tokamak plasmas using a multi-level tokamak code package. Several current applications using MHD and Extended-MHD models are presented; high-β disruption studies in reversed shear plasmas using the MHD level MH3D code, ω *i stabilization and nonlinear island rotation studies using the two-fluid level MH3D-T code, studies of nonlinear saturation of TAE modes using the hybrid particle/MHD level MH3D-K code, and unstructured mesh MH3D ++ code studies. In particular, three internal mode disruption mechanisms are identified from simulation results which agree well with experimental data

SU-D-BRF-06: A Brachytherapy Simulator with Realistic Haptic Force Feedback and Real-Time Ultrasounds Image Simulation for Training and Teaching

International Nuclear Information System (INIS)

Beaulieu, L; Carette, A; Comtois, S; Lavigueur, M; Cardou, P; Laurendeau, D

2014-01-01

Purpose: Surgical procedures require dexterity, expertise and repetition to reach optimal patient outcomes. However, efficient training opportunities are usually limited. This work presents a simulator system with realistic haptic force-feedback and full, real-time ultrasounds image simulation. Methods: The simulator is composed of a custom-made Linear-DELTA force-feedback robotic platform. The needle tip is mounted on a force gauge at the end effector of the robot, which responds to needle insertion by providing reaction forces. 3D geometry of the tissue is using a tetrahedral finite element mesh (FEM) mimicking tissue properties. As the needle is inserted/retracted, tissue deformation is computed using a mass-tensor nonlinear visco-elastic FEM. The real-time deformation is fed to the L-DELTA to take into account the force imparted to the needle, providing feedback to the end-user when crossing tissue boundaries or needle bending. Real-time 2D US image is also generated synchronously showing anatomy, needle insertion and tissue deformation. The simulator is running on an Intel I7 6- core CPU at 3.26 MHz. 3D tissue rendering and ultrasound display are performed on a Windows 7 computer; the FEM computation and L-DELTA control are executed on a similar PC using the Neutrino real-time OS. Both machines communicate through an Ethernet link. Results: The system runs at 500 Hz for a 8333-tetrahedron tissue mesh and a 100-node angular spring needle model. This frame rate ensures a relatively smooth displacement of the needle when pushed or retracted (±20 N in all directions at speeds of up to 2 m/s). Unlike commercially-available haptic platforms, the oblong workspace of the L-DELTA robot complies with that required for brachytherapy needle displacements of 0.1m by 0.1m by 0.25m. Conclusion: We have demonstrated a real-life, realistic brachytherapy simulator developed for prostate implants (LDR/HDR). The platform could be adapted to other sites or training for other

The application of modern electric systems to T and D infrastructures to achieve EU 20/20/20 climate and energy targets

International Nuclear Information System (INIS)

Bonfiglio, A.; Delfino, F.; Denegri, G.B.; Invernizzi, M.; Procopio, R.; Pampararo, F.; Amann, G.; Bessede, J. L.; Luxa, A.; Monizza, G.

2011-03-01

This paper is the outcome of a collaboration between T and D Europe - The European Association of the Electricity Transmission and Distribution Equipment and Services Industry and the Power Systems Research Team at the University of Genoa. It presents a scientific analysis of how much modern products and systems from the electric industry contribute to the European Union's (EU) efforts to mitigate climate change (EU's Climate and Energy Policy 20/20/20 [1]). A methodology is proposed in order to quantify the possible environmental benefits in terms of efficiency increase, CO 2 reduction and a wider employ of renewable energy resources as well as of power quality improvement provided by a renewal of the European T and D infrastructures. Such methodology is based both on the identification of suitable technical KPIs (Key Performance Indicators) to be used to rank the benefits brought by the different grid upgrading measures and on the definition of suitable 'test networks', which can be employed as benchmarks to perform the numerical evaluation of the introduced KPIs. (authors)

The application of modern electric systems to T and D infrastructures to achieve EU 20/20/20 climate and energy targets

Energy Technology Data Exchange (ETDEWEB)

Bonfiglio, A.; Delfino, F.; Denegri, G.B.; Invernizzi, M.; Procopio, R.; Pampararo, F. [Department of Electrical Engineering, University of Genoa, via Opera Pia, 11 a, I-16145 Genova (Italy); Amann, G.; Bessede, J. L.; Luxa, A.; Monizza, G. [T and D Europe - The European Association of the Electricity Transmission and Distribution Equipment and Services Industry, Diamant Building, Boulevard A. Reyers 80, B 1030 Brussels (Belgium)

2011-03-15

This paper is the outcome of a collaboration between T and D Europe - The European Association of the Electricity Transmission and Distribution Equipment and Services Industry and the Power Systems Research Team at the University of Genoa. It presents a scientific analysis of how much modern products and systems from the electric industry contribute to the European Union's (EU) efforts to mitigate climate change (EU's Climate and Energy Policy 20/20/20 [1]). A methodology is proposed in order to quantify the possible environmental benefits in terms of efficiency increase, CO{sub 2} reduction and a wider employ of renewable energy resources as well as of power quality improvement provided by a renewal of the European T and D infrastructures. Such methodology is based both on the identification of suitable technical KPIs (Key Performance Indicators) to be used to rank the benefits brought by the different grid upgrading measures and on the definition of suitable 'test networks', which can be employed as benchmarks to perform the numerical evaluation of the introduced KPIs. (authors)

Massively-parallel FDTD simulations to address mask electromagnetic effects in hyper-NA immersion lithography

Science.gov (United States)

Tirapu Azpiroz, Jaione; Burr, Geoffrey W.; Rosenbluth, Alan E.; Hibbs, Michael

2008-03-01

In the Hyper-NA immersion lithography regime, the electromagnetic response of the reticle is known to deviate in a complicated manner from the idealized Thin-Mask-like behavior. Already, this is driving certain RET choices, such as the use of polarized illumination and the customization of reticle film stacks. Unfortunately, full 3-D electromagnetic mask simulations are computationally intensive. And while OPC-compatible mask electromagnetic field (EMF) models can offer a reasonable tradeoff between speed and accuracy for full-chip OPC applications, full understanding of these complex physical effects demands higher accuracy. Our paper describes recent advances in leveraging High Performance Computing as a critical step towards lithographic modeling of the full manufacturing process. In this paper, highly accurate full 3-D electromagnetic simulation of very large mask layouts are conducted in parallel with reasonable turnaround time, using a Blue- Gene/L supercomputer and a Finite-Difference Time-Domain (FDTD) code developed internally within IBM. A 3-D simulation of a large 2-D layout spanning 5μm×5μm at the wafer plane (and thus (20μm×20μm×0.5μm at the mask) results in a simulation with roughly 12.5GB of memory (grid size of 10nm at the mask, single-precision computation, about 30 bytes/grid point). FDTD is flexible and easily parallelizable to enable full simulations of such large layout in approximately an hour using one BlueGene/L "midplane" containing 512 dual-processor nodes with 256MB of memory per processor. Our scaling studies on BlueGene/L demonstrate that simulations up to 100μm × 100μm at the mask can be computed in a few hours. Finally, we will show that the use of a subcell technique permits accurate simulation of features smaller than the grid discretization, thus improving on the tradeoff between computational complexity and simulation accuracy. We demonstrate the correlation of the real and quadrature components that comprise the

File list: NoD.Bld.20.AllAg.Peripheral_blood [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Bld.20.AllAg.Peripheral_blood hg19 No description Blood Peripheral blood SRX100...034080,SRX1034076,SRX1034079,SRX1034072,SRX1034078,SRX848890,SRX1034067 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Bld.20.AllAg.Peripheral_blood.bed ...

Simulation and test of 3D silicon radiation detectors

International Nuclear Information System (INIS)

Fleta, C.; Pennicard, D.; Bates, R.; Parkes, C.; Pellegrini, G.; Lozano, M.; Wright, V.; Boscardin, M.; Dalla Betta, G.-F.; Piemonte, C.; Pozza, A.; Ronchin, S.; Zorzi, N.

2007-01-01

The work presented here is the result of the collaborative effort between the University of Glasgow, ITC-IRST (Trento) and IMB-CNM (Barcelona) in the framework of the CERN-RD50 Collaboration to produce 3D silicon radiation detectors and study their performance. This paper reports on two sets of 3D devices. IRST and CNM have fabricated a set of single-type column 3D detectors, which have columnar electrodes of the same doping type and an ohmic contact located at the backplane. Simulations of the device behaviour and electrical test results are presented. In particular, current-voltage, capacitance-voltage and charge collection efficiency measurements are reported. Other types of structures called double-sided 3D detectors are currently being fabricated at CNM. In these detectors the sets of n and p columns are made on opposite sides of the device. Electrical and technological simulations and first processing results are presented

2D PIM Simulation Based on COMSOL

DEFF Research Database (Denmark)

Wang, Xinbo; Cui, Wanzhao; Wang, Jingyu

2011-01-01

Passive intermodulation (PIM) is a problematic type of nonlinear distortion en- countered in many communication systems. To analyze the PIM distortion resulting from ma- terial nonlinearity, a 2D PIM simulation method based on COMSOL is proposed in this paper. As an example, a rectangular wavegui...

3D Simulation of Nano-Imprint Lithography

DEFF Research Database (Denmark)

Román Marín, José Manuel; Rasmussen, Henrik K.; Hassager, Ole

2010-01-01

A proof of concept study of the feasibility of fully three-dimensional (3D) time-dependent simulation of nano-imprint lithography of polymer melt, where the polymer is treated as a structured liquid, has been presented. Considering the flow physics of the polymer as a structured liquid, we have...

40 CFR 96.83 - Applying for NOX Budget opt-in permit.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Applying for NOX Budget opt-in permit... PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS Individual Unit Opt-ins § 96.83 Applying for NOX Budget opt-in permit. (a) Applying for...

[3D Virtual Reality Laparoscopic Simulation in Surgical Education - Results of a Pilot Study].

Science.gov (United States)

Kneist, W; Huber, T; Paschold, M; Lang, H

2016-06-01

The use of three-dimensional imaging in laparoscopy is a growing issue and has led to 3D systems in laparoscopic simulation. Studies on box trainers have shown differing results concerning the benefit of 3D imaging. There are currently no studies analysing 3D imaging in virtual reality laparoscopy (VRL). Five surgical fellows, 10 surgical residents and 29 undergraduate medical students performed abstract and procedural tasks on a VRL simulator using conventional 2D and 3D imaging in a randomised order. No significant differences between the two imaging systems were shown for students or medical professionals. Participants who preferred three-dimensional imaging showed significantly better results in 2D as wells as in 3D imaging. First results on three-dimensional imaging on box trainers showed different results. Some studies resulted in an advantage of 3D imaging for laparoscopic novices. This study did not confirm the superiority of 3D imaging over conventional 2D imaging in a VRL simulator. In the present study on 3D imaging on a VRL simulator there was no significant advantage for 3D imaging compared to conventional 2D imaging. Georg Thieme Verlag KG Stuttgart · New York.

The simulation of 3D mass models in 2D digital mammography and breast tomosynthesis

Energy Technology Data Exchange (ETDEWEB)

Shaheen, Eman, E-mail: eman.shaheen@uzleuven.be; De Keyzer, Frederik; Bosmans, Hilde; Ongeval, Chantal Van [Department of Radiology, University Hospitals Leuven, Herestraat 49, 3000 Leuven (Belgium); Dance, David R.; Young, Kenneth C. [National Coordinating Centre for the Physics of Mammography, Royal Surrey County Hospital, Guildford GU2 7XX, United Kingdom and Department of Physics, Faculty of Engineering and Physical Sciences, University of Surrey, Guildford GU2 7XH (United Kingdom)

2014-08-15

Purpose: This work proposes a new method of building 3D breast mass models with different morphological shapes and describes the validation of the realism of their appearance after simulation into 2D digital mammograms and breast tomosynthesis images. Methods: Twenty-five contrast enhanced MRI breast lesions were collected and each mass was manually segmented in the three orthogonal views: sagittal, coronal, and transversal. The segmented models were combined, resampled to have isotropic voxel sizes, triangularly meshed, and scaled to different sizes. These masses were referred to as nonspiculated masses and were then used as nuclei onto which spicules were grown with an iterative branching algorithm forming a total of 30 spiculated masses. These 55 mass models were projected into 2D projection images to obtain mammograms after image processing and into tomographic sequences of projection images, which were then reconstructed to form 3D tomosynthesis datasets. The realism of the appearance of these mass models was assessed by five radiologists via receiver operating characteristic (ROC) analysis when compared to 54 real masses. All lesions were also given a breast imaging reporting and data system (BIRADS) score. The data sets of 2D mammography and tomosynthesis were read separately. The Kendall's coefficient of concordance was used for the interrater observer agreement assessment for the BIRADS scores per modality. Further paired analysis, using the Wilcoxon signed rank test, of the BIRADS assessment between 2D and tomosynthesis was separately performed for the real masses and for the simulated masses. Results: The area under the ROC curves, averaged over all observers, was 0.54 (95% confidence interval [0.50, 0.66]) for the 2D study, and 0.67 (95% confidence interval [0.55, 0.79]) for the tomosynthesis study. According to the BIRADS scores, the nonspiculated and the spiculated masses varied in their degrees of malignancy from normal (BIRADS 1) to highly

The simulation of 3D mass models in 2D digital mammography and breast tomosynthesis

International Nuclear Information System (INIS)

Shaheen, Eman; De Keyzer, Frederik; Bosmans, Hilde; Ongeval, Chantal Van; Dance, David R.; Young, Kenneth C.

2014-01-01

Purpose: This work proposes a new method of building 3D breast mass models with different morphological shapes and describes the validation of the realism of their appearance after simulation into 2D digital mammograms and breast tomosynthesis images. Methods: Twenty-five contrast enhanced MRI breast lesions were collected and each mass was manually segmented in the three orthogonal views: sagittal, coronal, and transversal. The segmented models were combined, resampled to have isotropic voxel sizes, triangularly meshed, and scaled to different sizes. These masses were referred to as nonspiculated masses and were then used as nuclei onto which spicules were grown with an iterative branching algorithm forming a total of 30 spiculated masses. These 55 mass models were projected into 2D projection images to obtain mammograms after image processing and into tomographic sequences of projection images, which were then reconstructed to form 3D tomosynthesis datasets. The realism of the appearance of these mass models was assessed by five radiologists via receiver operating characteristic (ROC) analysis when compared to 54 real masses. All lesions were also given a breast imaging reporting and data system (BIRADS) score. The data sets of 2D mammography and tomosynthesis were read separately. The Kendall's coefficient of concordance was used for the interrater observer agreement assessment for the BIRADS scores per modality. Further paired analysis, using the Wilcoxon signed rank test, of the BIRADS assessment between 2D and tomosynthesis was separately performed for the real masses and for the simulated masses. Results: The area under the ROC curves, averaged over all observers, was 0.54 (95% confidence interval [0.50, 0.66]) for the 2D study, and 0.67 (95% confidence interval [0.55, 0.79]) for the tomosynthesis study. According to the BIRADS scores, the nonspiculated and the spiculated masses varied in their degrees of malignancy from normal (BIRADS 1) to highly

The simulation of 3D mass models in 2D digital mammography and breast tomosynthesis.

Science.gov (United States)

Shaheen, Eman; De Keyzer, Frederik; Bosmans, Hilde; Dance, David R; Young, Kenneth C; Van Ongeval, Chantal

2014-08-01

This work proposes a new method of building 3D breast mass models with different morphological shapes and describes the validation of the realism of their appearance after simulation into 2D digital mammograms and breast tomosynthesis images. Twenty-five contrast enhanced MRI breast lesions were collected and each mass was manually segmented in the three orthogonal views: sagittal, coronal, and transversal. The segmented models were combined, resampled to have isotropic voxel sizes, triangularly meshed, and scaled to different sizes. These masses were referred to as nonspiculated masses and were then used as nuclei onto which spicules were grown with an iterative branching algorithm forming a total of 30 spiculated masses. These 55 mass models were projected into 2D projection images to obtain mammograms after image processing and into tomographic sequences of projection images, which were then reconstructed to form 3D tomosynthesis datasets. The realism of the appearance of these mass models was assessed by five radiologists via receiver operating characteristic (ROC) analysis when compared to 54 real masses. All lesions were also given a breast imaging reporting and data system (BIRADS) score. The data sets of 2D mammography and tomosynthesis were read separately. The Kendall's coefficient of concordance was used for the interrater observer agreement assessment for the BIRADS scores per modality. Further paired analysis, using the Wilcoxon signed rank test, of the BIRADS assessment between 2D and tomosynthesis was separately performed for the real masses and for the simulated masses. The area under the ROC curves, averaged over all observers, was 0.54 (95% confidence interval [0.50, 0.66]) for the 2D study, and 0.67 (95% confidence interval [0.55, 0.79]) for the tomosynthesis study. According to the BIRADS scores, the nonspiculated and the spiculated masses varied in their degrees of malignancy from normal (BIRADS 1) to highly suggestive for malignancy (BIRADS 5

Optimization of FIBMOS Through 2D Silvaco ATLAS and 2D Monte Carlo Particle-based Device Simulations

OpenAIRE

Kang, J.; He, X.; Vasileska, D.; Schroder, D. K.

2001-01-01

Focused Ion Beam MOSFETs (FIBMOS) demonstrate large enhancements in core device performance areas such as output resistance, hot electron reliability and voltage stability upon channel length or drain voltage variation. In this work, we describe an optimization technique for FIBMOS threshold voltage characterization using the 2D Silvaco ATLAS simulator. Both ATLAS and 2D Monte Carlo particle-based simulations were used to show that FIBMOS devices exhibit enhanced current drive ...

File list: NoD.Neu.20.AllAg.Superior_Cervical_Ganglion [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Superior_Cervical_Ganglion mm9 No description Neural Superior Cervical Ganglion... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Neu.20.AllAg.Superior_Cervical_Ganglion.bed ...

File list: NoD.Adp.20.AllAg.Adipose_Tissue,_White [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Adp.20.AllAg.Adipose_Tissue,_White hg19 No description Adipocyte Adipose Tissue..., White http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Adp.20.AllAg.Adipose_Tissue,_White.bed ...

File list: NoD.Neu.20.AllAg.Induced_neural_progenitors [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Induced_neural_progenitors mm9 No description Neural Induced neural... progenitors http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Neu.20.AllAg.Induced_neural_progenitors.bed ...

File list: NoD.Neu.20.AllAg.Cerebellar_granule_neurons [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Cerebellar_granule_neurons mm9 No description Neural Cerebellar granule neurons... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Neu.20.AllAg.Cerebellar_granule_neurons.bed ...

Grout Treatment Facility dangerous waste permit application

International Nuclear Information System (INIS)

1992-07-01

The Grout Treatment Facility (GTF) is an existing treatment, storage, and/or disposal (TSD) unit located in the 200 East Area and the adjacent 600 Area of the Hanford Site. The GTF mixes dry cementitious solids with liquid mixed waste (containing both dangerous and radioactive constituents) produced by Hanford Site operations. The GTF consists of the following: The 241-AP-02D and 241-AP-04D waste pump pits and transfer piping; Dry Materials Facility (DMF); Grout Disposal Facility (GDF), consisting of the disposal vault and support and monitoring equipment; and Grout Processing Facility (GPF) and Westinghouse Hanford Company on the draft Hanford Facility Dangerous Waste Permit and may not be read to conflict with those comments. The Grout Treatment Facility Dangerous Waste Permit Application consists of both a Part A and a Part B permit application. An explanation of the Part A revisions associated with this TSD unit, including the current revision, is provided at the beginning of the Part A section. The Part B consists of 15 chapters addressing the organization and content of the Part B checklist prepared by the Washington State Department of Ecology (Ecology 1987). For ease of reference, the checklist section numbers, in brackets, follow chapter headings and subheadings

Etude par simulation hil des performances d'un statcom pour la ...

African Journals Online (AJOL)

Ce travail présente l'étude par simulation Hardware In the Loop (HIL) des performances d'un STATCOM pour la stabilisation de la tension délivrée par une génératrice asynchrone triphasée auto excitée dans un réseau autonome. Nous avons combiné l'utilisation du logiciel de simulation LABVIEW et la carte ARDUINO ...

The simulation methods based on 1D/3D collaborative computing for the vehicle integrated thermal management

International Nuclear Information System (INIS)

Lu, Pengyu; Gao, Qing; Wang, Yan

2016-01-01

Highlights: • A 1D/3D collaborative computing simulation method for vehicle thermal management. • Analyzing the influence of the thermodynamic systems and the engine compartment geometry on the vehicle performance. • Providing the basis for the matching energy consumptions of thermodynamic systems in the underhood. - Abstract: The vehicle integrated thermal management containing the engine cooling circuit, the air conditioning circuit, the turbocharged inter-cooled circuit, the engine lubrication circuit etc. is the important means of enhancing power performance, promoting economy, saving energy and reducing emission. In this study, a 1D/3D collaborative simulation method is proposed with the engine cooling circuit and air conditioning circuit being the research object. The mathematical characterizations of the multiple thermodynamic systems are achieved by 1D calculation and the underhood structure is described by 3D simulation. Through analyzing the engine compartment integrated heat transfer process, the model of the integrated thermal management system is formed after coupling the cooling circuit and air conditioning circuit. This collaborative simulation method establishes structured correlation of engine-cooling and air conditioning thermal dissipation in the engine compartment, comprehensively analyzing the engine working process and air condition operational process in order to research the interaction effect of them. In the calculation examples, to achieve the integrated optimization of multiple thermal systems design and performance prediction, by describing the influence of system thermomechanical parameters and operating duty to underhood heat transfer process, performance evaluation of the engine cooling circuit and the air conditioning circuit are realized.

File list: NoD.PSC.20.AllAg.STAP_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.STAP_cells mm9 No description Pluripotent stem cell STAP cells SRX...472660,SRX472654,SRX472663,SRX472661,SRX472656,SRX472665,SRX472662,SRX472655,SRX472664 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.PSC.20.AllAg.STAP_cells.bed ...

Comparison between a coupled 1D-2D model and a fully 2D model for supercritical flow simulation in crossroads

KAUST Repository

Ghostine, Rabih

2014-12-01

In open channel networks, flow is usually approximated by the one-dimensional (1D) Saint-Venant equations coupled with an empirical junction model. In this work, a comparison in terms of accuracy and computational cost between a coupled 1D-2D shallow water model and a fully two-dimensional (2D) model is presented. The paper explores the ability of a coupled model to simulate the flow processes during supercritical flows in crossroads. This combination leads to a significant reduction in the computational time, as a 1D approach is used in branches and a 2D approach is employed in selected areas only where detailed flow information is essential. Overall, the numerical results suggest that the coupled model is able to accurately simulate the main flow processes. In particular, hydraulic jumps, recirculation zones, and discharge distribution are reasonably well reproduced and clearly identified. Overall, the proposed model leads to a 30% reduction in run times. © 2014 International Association for Hydro-Environment Engineering and Research.

Simulation, modélisation et décision en pratique

CERN Document Server

Rennard, Jean-Philippe; Duymedjian, Raffi

2009-01-01

Avec l'explosion de la puissance informatique, le grand public dispose désormais d'outils aptes à résoudre des problèmes complexes, auparavant hors de portée des non-spécialistes. Le tableur notamment est particulièrement adapté à la modélisation et à la simulation de nombre de problèmes quotidiens de décision. En parallèle, le décideur est confronté à un environnement en évolution rapide, où la décision éclairée est une condition de succès. Face à une avalanche de données, il est le plus souvent amené à sélection intuitivement celles qui sont susceptibles de l'aide à anticiper les conséquences de ses décisions. Cet ouvrage se propose de présenter les principale méthodes d'aide à la décision et d'en montrer la mise en oeuvre avec le tableur. D'une difficulté progressive, l'ouvrage introduit à la modélisation e à la simulation pour la décision avant de présenter les outils dédiés à différents types de problèmes (prévision, optimisation, théorie des jeux, arbres d...

File list: NoD.Oth.20.AllAg.Pancreas_and_brain [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Oth.20.AllAg.Pancreas_and_brain mm9 No description Others Pancreas and brain ht...tp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Oth.20.AllAg.Pancreas_and_brain.bed ...

File list: NoD.PSC.20.AllAg.iPSC_intermediates [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.iPSC_intermediates mm9 No description Pluripotent stem cell iPSC intermediates... http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.PSC.20.AllAg.iPSC_intermediates.bed ...

File list: NoD.Dig.20.AllAg.Intestinal_stem_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Dig.20.AllAg.Intestinal_stem_cells mm9 No description Digestive tract Intestina...l stem cells http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Dig.20.AllAg.Intestinal_stem_cells.bed ...

File list: NoD.Emb.20.AllAg.Pre-somitic_mesoderm [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Emb.20.AllAg.Pre-somitic_mesoderm mm9 No description Embryo Pre-somitic mesoder...m http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Emb.20.AllAg.Pre-somitic_mesoderm.bed ...

File list: NoD.Adp.20.AllAg.Adipose_progenitor_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Adp.20.AllAg.Adipose_progenitor_cells mm9 No description Adipocyte Adipose progeni...tor cells http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Adp.20.AllAg.Adipose_progenitor_cells.bed ...

File list: NoD.Gon.20.AllAg.Testicular_somatic_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Gon.20.AllAg.Testicular_somatic_cells mm9 No description Gonad Testicular somat...ic cells http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Gon.20.AllAg.Testicular_somatic_cells.bed ...

File list: InP.NoD.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.20.Input_control.AllCell dm3 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/InP.NoD.20.Input_control.AllCell.bed ...

File list: Pol.NoD.20.RNA_polymerase_III.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Pol.NoD.20.RNA_polymerase_III.AllCell hg19 RNA polymerase RNA polymerase III No des...cription http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Pol.NoD.20.RNA_polymerase_III.AllCell.bed ...

File list: Pol.NoD.20.RNA_polymerase_II.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Pol.NoD.20.RNA_polymerase_II.AllCell hg19 RNA polymerase RNA polymerase II No descr...iption http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/Pol.NoD.20.RNA_polymerase_II.AllCell.bed ...

File list: NoD.Utr.20.AllAg.Endometrial_stromal_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Utr.20.AllAg.Endometrial_stromal_cells hg19 No description Uterus Endometrial s...tromal cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Utr.20.AllAg.Endometrial_stromal_cells.bed ...

File list: InP.NoD.20.Input_control.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available InP.NoD.20.Input_control.AllCell mm9 Input control Input control No description htt...p://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.NoD.20.Input_control.AllCell.bed ...

File list: NoD.Adl.20.AllAg.Adult_male_fatbody [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Adl.20.AllAg.Adult_male_fatbody dm3 No description Adult Adult male fatbody htt...p://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/NoD.Adl.20.AllAg.Adult_male_fatbody.bed ...

Charge collection characterization of a 3D silicon radiation detector by using 3D simulations

CERN Document Server

Kalliopuska, J; Orava, R

2007-01-01

In 3D detectors, the electrodes are processed within the bulk of the sensor material. Therefore, the signal charge is collected independently of the wafer thickness and the collection process is faster due to shorter distances between the charge collection electrodes as compared to a planar detector structure. In this paper, 3D simulations are used to assess the performance of a 3D detector structure in terms of charge sharing, efficiency and speed of charge collection, surface charge, location of the primary interaction and the bias voltage. The measured current pulse is proposed to be delayed due to the resistance–capacitance (RC) product induced by the variation of the serial resistance of the pixel electrode depending on the depth of the primary interaction. Extensive simulations are carried out to characterize the 3D detector structures and to verify the proposed explanation for the delay of the current pulse. A method for testing the hypothesis experimentally is suggested.

40 CFR 97.83 - Applying for NOX Budget opt-in permit.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Applying for NOX Budget opt-in permit... PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS Individual Unit Opt-ins. § 97.83 Applying for NOX Budget opt-in permit. (a) Applying for initial NO X Budget opt...

3D Printed Surgical Instruments Evaluated by a Simulated Crew of a Mars Mission.

Science.gov (United States)

Wong, Julielynn Y; Pfahnl, Andreas C

2016-09-01

The first space-based fused deposition modeling (FDM) 3D printer became operational in 2014. This study evaluated whether Mars simulation crewmembers of the Hawai'i Space Exploration Analog and Simulation (HI-SEAS) II mission with no prior surgical experience could utilize acrylonitrile butadiene styrene (ABS) thermoplastic surgical instruments FDM 3D printed on Earth to complete simulated surgical tasks. This study sought to examine the feasibility of using 3D printed surgical tools when the primary crew medical officer is incapacitated and the back-up crew medical officer must conduct a surgical procedure during a simulated extended space mission. During a 4 mo duration ground-based analog mission, five simulation crewmembers with no prior surgical experience completed 16 timed sets of simulated prepping, draping, incising, and suturing tasks to evaluate the relative speed of using four ABS thermoplastic instruments printed on Earth compared to conventional instruments. All four simulated surgical tasks were successfully performed using 3D printed instruments by Mars simulation crewmembers with no prior surgical experience. There was no substantial difference in time to completion of simulated tasks with control vs. 3D printed sponge stick, towel clamp, scalpel handle, and toothed forceps. These limited findings support further investigation into the creation of an onboard digital catalog of validated 3D printable surgical instrument design files to support autonomous, crew-administered healthcare on Mars missions. Future work could include addressing sterility, biocompatibility, and having astronaut crew medical officers test a wider range of surgical instruments printed in microgravity during actual surgical procedures. Wong JY, Pfahnl AC. 3D printed surgical instruments evaluated by a simulated crew of a Mars mission. Aerosp Med Hum Perform. 2016; 87(9):806-810.

3D printed 20/30-GHz dual-band offset stepped-reflector antenna

DEFF Research Database (Denmark)

Menendez, Laura G.; Kim, Oleksiy S.; Persson, Frank

2015-01-01

with a peak directivity of 36.7 dB and 40.4 dB at 20 and 30 GHz, respectively; this corresponds to an aperture efficiency of 61 % and 64 %, respectively. These results demonstrate that 3D printing is a viable manufacturing technology for medium-sized high-frequency antennas....

3D Core Model for simulation of nuclear power plants: Simulation requirements, model features, and validation

International Nuclear Information System (INIS)

Zerbino, H.

1999-01-01

In 1994-1996, Thomson Training and Simulation (TT and S) earned out the D50 Project, which involved the design and construction of optimized replica simulators for one Dutch and three German Nuclear Power Plants. It was recognized early on that the faithful reproduction of the Siemens reactor control and protection systems would impose extremely stringent demands on the simulation models, particularly the Core physics and the RCS thermohydraulics. The quality of the models, and their thorough validation, were thus essential. The present paper describes the main features of the fully 3D Core model implemented by TT and S, and its extensive validation campaign, which was defined in extremely positive collaboration with the Customer and the Core Data suppliers. (author)

File list: NoD.Neu.20.AllAg.Neural_progenitor_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Neural_progenitor_cells mm9 No description Neural Neural progenito...SRX346675,SRX346817 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Neu.20.AllAg.Neural_progenitor_cells.bed ...

File list: NoD.CDV.20.AllAg.Brachiocephalic_endothelial_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.CDV.20.AllAg.Brachiocephalic_endothelial_cells hg19 No description Cardiovascular Brachiocephal...ic endothelial cells DRX014747 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.CDV.20.AllAg.Brachiocephalic_endothelial_cells.bed ...

File list: NoD.PSC.20.AllAg.mESCs,_differentiated [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.mESCs,_differentiated mm9 No description Pluripotent stem cell mESCs, differentia...ted http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.PSC.20.AllAg.mESCs,_differentiated.bed ...

File list: Pol.NoD.20.RNA_polymerase_II.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Pol.NoD.20.RNA_polymerase_II.AllCell sacCer3 RNA polymerase RNA polymerase II No de...scription http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/Pol.NoD.20.RNA_polymerase_II.AllCell.bed ...

12 CFR 563.146 - Will the OTS permit my capital distribution?

Science.gov (United States)

2010-01-01

... under 12 U.S.C. 1831o(d)(1)(B). (b) Your proposed capital distribution raises safety or soundness... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Will the OTS permit my capital distribution... SAVINGS ASSOCIATIONS-OPERATIONS Capital Distributions § 563.146 Will the OTS permit my capital...

Multi-physic simulations of irradiation experiments in a technological irradiation reactor; Modelisation pluridisciplinaire d'experiences d'irradiation dans un reacteur d'irradiation technologique

Energy Technology Data Exchange (ETDEWEB)

Bonaccorsi, Th

2007-09-15

A Material Testing Reactor (MTR) makes it possible to irradiate material samples under intense neutron and photonic fluxes. These experiments are carried out in experimental devices localised in the reactor core or in periphery (reflector). Available physics simulation tools only treat, most of the time, one physics field in a very precise way. Multi-physic simulations of irradiation experiments therefore require a sequential use of several calculation codes and data exchanges between these codes: this corresponds to problems coupling. In order to facilitate multi-physic simulations, this thesis sets up a data model based on data-processing objects, called Technological Entities. This data model is common to all of the physics fields. It permits defining the geometry of an irradiation device in a parametric way and to associate information about materials to it. Numerical simulations are encapsulated into interfaces providing the ability to call specific functionalities with the same command (to initialize data, to launch calculations, to post-treat, to get results,... ). Thus, once encapsulated, numerical simulations can be re-used for various studies. This data model is developed in a SALOME platform component. The first application case made it possible to perform neutronic simulations (OSIRIS reactor and RJH) coupled with fuel behavior simulations. In a next step, thermal hydraulics could also be taken into account. In addition to the improvement of the calculation accuracy due to the physical phenomena coupling, the time spent in the development phase of the simulation is largely reduced and the possibilities of uncertainty treatment are under consideration. (author)

Intramuscular depot formulations of leuprolide acetate suppress testosterone levels below a 20 ng/dL threshold: a retrospective analysis of two Phase III studies

Directory of Open Access Journals (Sweden)

Spitz A

2016-08-01

Full Text Available Aaron Spitz,1 Marc Gittelman,2 Lawrence I Karsh,3 Sanja Dragnic,4 Ahmed M Soliman,5 Aditya Lele,6 Damian Gruca,7 Michael Norton4 1Orange County Urology Associates, Laguna Beach, CA, 221st Century Oncology/UroMedix-Aventura Division, Aventura, FL, 3The Urology Center of Colorado, Denver, CO, 4US Medical Affairs, 5Health Economics and Outcomes Research, 6Data and Statistical Sciences, AbbVie Inc., North Chicago, IL, USA; 7Global Medical Affairs, AbbVie Deutschland, Ludwigshafen, Germany Introduction: Androgen deprivation therapy (ADT with gonadotropin-releasing hormone (GnRH analogs is a standard treatment for advanced prostate cancer. GnRH analog therapy can reduce testosterone to “castrate” levels, historically defined as <50 ng/dL. With the advent of newer assays, a lower threshold of <20 ng/dL has recently been proposed. We report the results of a retrospective analysis of two Phase III trials of 4- and 6-month depot microsphere formulations of leuprolide acetate (LA, a GnRH agonist that has previously demonstrated efficacy in testosterone suppression to <50 ng/dL in patients on ADT. This analysis investigates the ability of these LA formulations to suppress to ≤20 ng/dL levels.Methods: In two of five AbbVie/Abbott clinical trials of microsphere formulations of LA for ADT, analytic technology permitting testosterone detection as low as 3 ng/dL was used and thus was selected for this analysis. Both trials were open-label, fixed-dose studies in prostate cancer patients, naïve to ADT. Patients received either 30 mg (4-month formulation; n=49 or 45 mg (6-month formulation; n=151 depot injections of LA microspheres. Treatment duration was up to 32 weeks for the 4-month formulation and 48 weeks for the 6-month formulation. The proportion of patients achieving the 20 ng/dL threshold was determined every 4 weeks.Results: Pooled analysis showed that 152 of 193 (79% of patients achieved serum testosterone levels of ≤20 ng/dL at 4 weeks, and

File list: Oth.NoD.20.DNA-RNA_hybrids.AllCell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available Oth.NoD.20.DNA-RNA_hybrids.AllCell sacCer3 TFs and others DNA-RNA hybrids No descri...ption http://dbarchive.biosciencedbc.jp/kyushu-u/sacCer3/assembled/Oth.NoD.20.DNA-RNA_hybrids.AllCell.bed ...

IRFK2D: a computer program for simulating intrinsic random functions of order k

Science.gov (United States)

Pardo-Igúzquiza, Eulogio; Dowd, Peter A.

2003-07-01

IRFK2D is an ANSI Fortran-77 program that generates realizations of an intrinsic function of order k (with k equal to 0, 1 or 2) with a permissible polynomial generalized covariance model. The realizations may be non-conditional or conditioned to the experimental data. The turning bands method is used to generate realizations in 2D and 3D from simulations of an intrinsic random function of order k along lines that span the 2D or 3D space. The program generates two output files, the first containing the simulated values and the second containing the theoretical generalized variogram for different directions together with the theoretical model. The experimental variogram is calculated from the simulated values while the theoretical variogram is the specified generalized covariance model. The generalized variogram is used to assess the quality of the simulation as measured by the extent to which the generalized covariance is reproduced by the simulation. The examples given in this paper indicate that IRFK2D is an efficient implementation of the methodology.

Lattice simulation of 2d Gross-Neveu-type models

International Nuclear Information System (INIS)

Limmer, M.; Gattringer, C.; Hermann, V.

2006-01-01

Full text: We discuss a Monte Carlo simulation of 2d Gross-Neveu-type models on the lattice. The four-Fermi interaction is written as a Gaussian integral with an auxiliary field and the fermion determinant is included by reweighting. We present results for bulk quantities and correlators and compare them to a simulation using a fermion-loop representation. (author)

Hanford facility dangerous waste permit application, low-level burial grounds

International Nuclear Information System (INIS)

Engelmann, R.H.

1997-01-01

The Hanford Facility Dangerous Plaste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, 'operating' treatment, storage, and/or disposal units, such as the Low-Level Burial Grounds (this document, DOE/RL-88-20)

Hanford facility dangerous waste permit application, low-level burial grounds

Energy Technology Data Exchange (ETDEWEB)

Engelmann, R.H.

1997-08-12

The Hanford Facility Dangerous Plaste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, `operating` treatment, storage, and/or disposal units, such as the Low-Level Burial Grounds (this document, DOE/RL-88-20).

A STUDY ON USING 3D VISUALIZATION AND SIMULATION PROGRAM (OPTITEX 3D ON LEATHER APPAREL

Directory of Open Access Journals (Sweden)

Ork Nilay

2016-05-01

Full Text Available Leather is a luxury garment. Design, material, labor, fitting and time costs are very effective on the production cost of the consumer leather good. 3D visualization and simulation programs which are getting popular in textile industry can be used for material, labor and time saving in leather apparel. However these programs have a very limited use in leather industry because leather material databases are not sufficient as in textile industry. In this research, firstly material properties of leather and textile fabric were determined by using both textile and leather physical test methods, and interpreted and introduced in the program. Detailed measures of an experimental human body were measured from a 3D body scanner. An avatar was designed according to these measurements. Then a prototype dress was made by using Computer Aided Design-CAD program for designing the patterns. After the pattern making, OptiTex 3D visualization and simulation program was used to visualize and simulate the dresses. Additionally the leather and cotton fabric dresses were sewn in real life. Then the visual and real life dresses were compared and discussed. 3D virtual prototyping seems a promising potential in future manufacturing technologies by evaluating the fitting of garments in a simple and quick way, filling the gap between 3D pattern design and manufacturing, providing virtual demonstrations to customers.

3D and 4D Simulations for Landscape Reconstruction and Damage Scenarios: GIS Pilot Applications

Science.gov (United States)

Pesaresi, Cristano; Van Der Schee, Joop; Pavia, Davide

2017-01-01

The project "3D and 4D Simulations for Landscape Reconstruction and Damage Scenarios: GIS Pilot Applications" has been devised with the intention to deal with the demand for research, innovation and applicative methodology on the part of the international programme, requiring concrete results to increase the capacity to know, anticipate…

A Novel Temporal Bone Simulation Model Using 3D Printing Techniques.

Science.gov (United States)

Mowry, Sarah E; Jammal, Hachem; Myer, Charles; Solares, Clementino Arturo; Weinberger, Paul

2015-09-01

An inexpensive temporal bone model for use in a temporal bone dissection laboratory setting can be made using a commercially available, consumer-grade 3D printer. Several models for a simulated temporal bone have been described but use commercial-grade printers and materials to produce these models. The goal of this project was to produce a plastic simulated temporal bone on an inexpensive 3D printer that recreates the visual and haptic experience associated with drilling a human temporal bone. Images from a high-resolution CT of a normal temporal bone were converted into stereolithography files via commercially available software, with image conversion and print settings adjusted to achieve optimal print quality. The temporal bone model was printed using acrylonitrile butadiene styrene (ABS) plastic filament on a MakerBot 2x 3D printer. Simulated temporal bones were drilled by seven expert temporal bone surgeons, assessing the fidelity of the model as compared with a human cadaveric temporal bone. Using a four-point scale, the simulated bones were assessed for haptic experience and recreation of the temporal bone anatomy. The created model was felt to be an accurate representation of a human temporal bone. All raters felt strongly this would be a good training model for junior residents or to simulate difficult surgical anatomy. Material cost for each model was $1.92. A realistic, inexpensive, and easily reproducible temporal bone model can be created on a consumer-grade desktop 3D printer.

Differential anatomical expression of ganglioside GM1 species containing d18:1 or d20:1 sphingosine detected by MALDI Imaging Mass Spectrometry in mature rat brain

Directory of Open Access Journals (Sweden)

Nina eWeishaupt

2015-12-01

Full Text Available GM1 ganglioside plays a role in essential neuronal processes, including differentiation, survival and signaling. Yet, little is known about GM1 species with different sphingosine bases, such as the most abundant species containing 18 carbon atoms in the sphingosine chain (GM1d18:1, and the less abundant containing 20 carbon atoms (GM1d20:1. While absent in the early fetal brain, GM1d20:1 continues to increase throughout pre- and postnatal development and into old age, raising questions about the functional relevance of the GM1d18:1 to GM1d20:1 ratio. Matrix-assisted laser desorption/ionization (MALDI Imaging Mass Spectrometry is a novel technology that allows differentiation between these two GM1 species and quantification of their expression within an anatomical context. Using this technology, we find GM1d18:1/d20:1 expression ratios are highly specific to defined anatomical brain regions in adult rats. Thus, the ratio was significantly different among different thalamic nuclei and between the corpus callosum and internal capsule. Differential GM1d18:1/GM1d20:1 ratios measured in hippocampal subregions in rat brain complement previous studies conducted in mice. Across layers of the sensory cortex, opposing expression gradients were found for GM1d18:1 and GM1d20:1. Superficial layers demonstrated lower GM1d18:1 and higher GM1d20:1 signal than other layers, while in deep layers GM1d18:1 expression was relatively high and GM1d20:1 expression low. By far the highest GM1d18:1/d20:1 ratio was found in the amygdala. Differential expression of GM1 with d18:1- or d20:1-sphingosine bases in the adult rat brain suggests tight regulation of expression and points toward a distinct functional relevance for each of these GM1 species in neuronal processes.

i3Drive, a 3D interactive driving simulator.

Science.gov (United States)

Ambroz, Miha; Prebil, Ivan

2010-01-01

i3Drive, a wheeled-vehicle simulator, can accurately simulate vehicles of various configurations with up to eight wheels in real time on a desktop PC. It presents the vehicle dynamics as an interactive animation in a virtual 3D environment. The application is fully GUI-controlled, giving users an easy overview of the simulation parameters and letting them adjust those parameters interactively. It models all relevant vehicle systems, including the mechanical models of the suspension, power train, and braking and steering systems. The simulation results generally correspond well with actual measurements, making the system useful for studying vehicle performance in various driving scenarios. i3Drive is thus a worthy complement to other, more complex tools for vehicle-dynamics simulation and analysis.

PHISICS/RELAP5-3D Adaptive Time-Step Method Demonstrated for the HTTR LOFC#1 Simulation

Energy Technology Data Exchange (ETDEWEB)

Baker, Robin Ivey [Idaho National Lab. (INL), Idaho Falls, ID (United States); Balestra, Paolo [Univ. of Rome (Italy); Strydom, Gerhard [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-05-01

A collaborative effort between Japan Atomic Energy Agency (JAEA) and Idaho National Laboratory (INL) as part of the Civil Nuclear Energy Working Group is underway to model the high temperature engineering test reactor (HTTR) loss of forced cooling (LOFC) transient that was performed in December 2010. The coupled version of RELAP5-3D, a thermal fluids code, and PHISICS, a neutronics code, were used to model the transient. The focus of this report is to summarize the changes made to the PHISICS-RELAP5-3D code for implementing an adaptive time step methodology into the code for the first time, and to test it using the full HTTR PHISICS/RELAP5-3D model developed by JAEA and INL and the LOFC simulation. Various adaptive schemes are available based on flux or power convergence criteria that allow significantly larger time steps to be taken by the neutronics module. The report includes a description of the HTTR and the associated PHISICS/RELAP5-3D model test results as well as the University of Rome sub-contractor report documenting the adaptive time step theory and methodology implemented in PHISICS/RELAP5-3D. Two versions of the HTTR model were tested using 8 and 26 energy groups. It was found that most of the new adaptive methods lead to significant improvements in the LOFC simulation time required without significant accuracy penalties in the prediction of the fission power and the fuel temperature. In the best performing 8 group model scenarios, a LOFC simulation of 20 hours could be completed in real-time, or even less than real-time, compared with the previous version of the code that completed the same transient 3-8 times slower than real-time. A few of the user choice combinations between the methodologies available and the tolerance settings did however result in unacceptably high errors or insignificant gains in simulation time. The study is concluded with recommendations on which methods to use for this HTTR model. An important caveat is that these findings

Numerical simulation of the SLAC X-100 klystron using RKTW2D

International Nuclear Information System (INIS)

Ryne, R.D.; Vlieks, A.E.

1991-05-01

We have performed numerical simulations of the X-100 klystron being developed at Stanford Linear Accelerator Center. The X-100 is being developed as a possible source for the next generation of linear collider, and will be required to produce ∼100 MW of power for a duration of ∼800 ns. Our simulations were performed using the simulation programs RKTW1D and RKTW2D, developed at Lawrence Livermore National Laboratory. The codes were used to investigate the operation of the klystron over a wide range of operating conditions. We will present comparisons of the simulation results with experimental results. 3 refs., 5 figs

Flow MRI simulation in complex 3D geometries: Application to the cerebral venous network.

Science.gov (United States)

Fortin, Alexandre; Salmon, Stéphanie; Baruthio, Joseph; Delbany, Maya; Durand, Emmanuel

2018-02-05

Develop and evaluate a complete tool to include 3D fluid flows in MRI simulation, leveraging from existing software. Simulation of MR spin flow motion is of high interest in the study of flow artifacts and angiography. However, at present, only a few simulators include this option and most are restricted to static tissue imaging. An extension of JEMRIS, one of the most advanced high performance open-source simulation platforms to date, was developed. The implementation of a Lagrangian description of the flow allows simulating any MR experiment, including both static tissues and complex flow data from computational fluid dynamics. Simulations of simple flow models are compared with real experiments on a physical flow phantom. A realistic simulation of 3D flow MRI on the cerebral venous network is also carried out. Simulations and real experiments are in good agreement. The generality of the framework is illustrated in 2D and 3D with some common flow artifacts (misregistration and inflow enhancement) and with the three main angiographic techniques: phase contrast velocimetry (PC), time-of-flight, and contrast-enhanced imaging MRA. The framework provides a versatile and reusable tool for the simulation of any MRI experiment including physiological fluids and arbitrarily complex flow motion. © 2018 International Society for Magnetic Resonance in Medicine.

The computer simulation of 3d gas dynamics in a gas centrifuge

Science.gov (United States)

Borman, V. D.; Bogovalov, S. V.; Borisevich, V. D.; Tronin, I. V.; Tronin, V. N.

2016-09-01

We argue on the basis of the results of 2D analysis of the gas flow in gas centrifuges that a reliable calculation of the circulation of the gas and gas content in the gas centrifuge is possible only in frameworks of 3D numerical simulation of gas dynamics in the gas centrifuge (hereafter GC). The group from National research nuclear university, MEPhI, has created a computer code for 3D simulation of the gas flow in GC. The results of the computer simulations of the gas flows in GC are presented. A model Iguassu centrifuge is explored for the simulations. A nonaxisymmetric gas flow is produced due to interaction of the hypersonic rotating flow with the scoops for extraction of the product and waste flows from the GC. The scoops produce shock waves penetrating into a working camera of the GC and form spiral waves there.

The computer simulation of 3d gas dynamics in a gas centrifuge

International Nuclear Information System (INIS)

Borman, V D; Bogovalov, S V; Borisevich, V D; Tronin, I V; Tronin, V N

2016-01-01

We argue on the basis of the results of 2D analysis of the gas flow in gas centrifuges that a reliable calculation of the circulation of the gas and gas content in the gas centrifuge is possible only in frameworks of 3D numerical simulation of gas dynamics in the gas centrifuge (hereafter GC). The group from National research nuclear university, MEPhI, has created a computer code for 3D simulation of the gas flow in GC. The results of the computer simulations of the gas flows in GC are presented. A model Iguassu centrifuge is explored for the simulations. A nonaxisymmetric gas flow is produced due to interaction of the hypersonic rotating flow with the scoops for extraction of the product and waste flows from the GC. The scoops produce shock waves penetrating into a working camera of the GC and form spiral waves there. (paper)

GYRO Simulations of Core Momentum Transport in DIII-D and JET Plasmas

International Nuclear Information System (INIS)

Budny, R.V.; Candy, J.; Waltz, R.E.

2005-01-01

Momentum, energy, and particle transport in DIII-D and JET ELMy H-mode plasmas is simulated with GYRO and compared with measurements analyzed using TRANSP. The simulated transport depends sensitively on the nabla(T(sub)i) turbulence drive and the nabla(E(sub)r) turbulence suppression inputs. With their nominal values indicated by measurements, the simulations over-predict the momentum and energy transport in the DIII-D plasmas, and under-predict in the JET plasmas. Reducing |nabla(T(sub)i)| and increasing |nabla(E(sub)r)| by up to 15% leads to approximate agreement (within a factor of two) for the DIII-D cases. For the JET cases, increasing |nabla(T(sub)i)| or reducing |nabla(E(sub)r)| results in approximate agreement for the energy flow, but the ratio of the simulated energy and momentum flows remains higher than measurements by a factor of 2-4

Study of one-nucleon transfer reactions with polarized deuterons of 20 MeV

International Nuclear Information System (INIS)

Seichert, N.

1983-01-01

In this thesis the results of the study of (d vector,p), (d vector,t), and (d vector, 3 He) reactions at Esub(d)approx.=20 MeV on the target nuclei 16 O, 18 O, 28 Si, 36 Ar, 40 Ca, 48 Ca, 54 Cr, 65 Cu, 90 Zr, 144 Sm, and 208 Pb in the framework of a DWBA analysis are presented. The collection of the results of the analysis over this wide mass range shall permit a survey, how well the conventional DWBA describes the measured angular distributions of dsigma/dΩ(theta) and iT 11 (theta). Furthermore in justified cases the contribution of higher order processes (inelastic transfer) are studied by means of a CCBA analysis. The spectroscopical possibilities given by the measurement of the analyzing power iT 11 (theta) are presented in detail on the example of the reaction 144 Sm (d vector,p) 145 Sm. The analysis of the tensor analyzing power T 21 (theta) in the framework of a finite range DWBA in the last part of the thesis permits quantitative statements about the D state amplitude in the relative wave function of the deuteron, the triton, and of 3 He. (orig./HSI) [de

X-CSIT: a toolkit for simulating 2D pixel detectors

Science.gov (United States)

Joy, A.; Wing, M.; Hauf, S.; Kuster, M.; Rüter, T.

2015-04-01

A new, modular toolkit for creating simulations of 2D X-ray pixel detectors, X-CSIT (X-ray Camera SImulation Toolkit), is being developed. The toolkit uses three sequential simulations of detector processes which model photon interactions, electron charge cloud spreading with a high charge density plasma model and common electronic components used in detector readout. In addition, because of the wide variety in pixel detector design, X-CSIT has been designed as a modular platform so that existing functions can be modified or additional functionality added if the specific design of a detector demands it. X-CSIT will be used to create simulations of the detectors at the European XFEL, including three bespoke 2D detectors: the Adaptive Gain Integrating Pixel Detector (AGIPD), Large Pixel Detector (LPD) and DePFET Sensor with Signal Compression (DSSC). These simulations will be used by the detector group at the European XFEL for detector characterisation and calibration. For this purpose, X-CSIT has been integrated into the European XFEL's software framework, Karabo. This will further make it available to users to aid with the planning of experiments and analysis of data. In addition, X-CSIT will be released as a standalone, open source version for other users, collaborations and groups intending to create simulations of their own detectors.

Detection of anatomical changes in lung cancer patients with 2D time-integrated, 2D time-resolved and 3D time-integrated portal dosimetry: a simulation study

Science.gov (United States)

Wolfs, Cecile J. A.; Brás, Mariana G.; Schyns, Lotte E. J. R.; Nijsten, Sebastiaan M. J. J. G.; van Elmpt, Wouter; Scheib, Stefan G.; Baltes, Christof; Podesta, Mark; Verhaegen, Frank

2017-08-01

The aim of this work is to assess the performance of 2D time-integrated (2D-TI), 2D time-resolved (2D-TR) and 3D time-integrated (3D-TI) portal dosimetry in detecting dose discrepancies between the planned and (simulated) delivered dose caused by simulated changes in the anatomy of lung cancer patients. For six lung cancer patients, tumor shift, tumor regression and pleural effusion are simulated by modifying their CT images. Based on the modified CT images, time-integrated (TI) and time-resolved (TR) portal dose images (PDIs) are simulated and 3D-TI doses are calculated. The modified and original PDIs and 3D doses are compared by a gamma analysis with various gamma criteria. Furthermore, the difference in the D 95% (ΔD 95%) of the GTV is calculated and used as a gold standard. The correlation between the gamma fail rate and the ΔD 95% is investigated, as well the sensitivity and specificity of all combinations of portal dosimetry method, gamma criteria and gamma fail rate threshold. On the individual patient level, there is a correlation between the gamma fail rate and the ΔD 95%, which cannot be found at the group level. The sensitivity and specificity analysis showed that there is not one combination of portal dosimetry method, gamma criteria and gamma fail rate threshold that can detect all simulated anatomical changes. This work shows that it will be more beneficial to relate portal dosimetry and DVH analysis on the patient level, rather than trying to quantify a relationship for a group of patients. With regards to optimizing sensitivity and specificity, different combinations of portal dosimetry method, gamma criteria and gamma fail rate should be used to optimally detect certain types of anatomical changes.

Detection of anatomical changes in lung cancer patients with 2D time-integrated, 2D time-resolved and 3D time-integrated portal dosimetry: a simulation study.

Science.gov (United States)

Wolfs, Cecile J A; Brás, Mariana G; Schyns, Lotte E J R; Nijsten, Sebastiaan M J J G; van Elmpt, Wouter; Scheib, Stefan G; Baltes, Christof; Podesta, Mark; Verhaegen, Frank

2017-07-12

The aim of this work is to assess the performance of 2D time-integrated (2D-TI), 2D time-resolved (2D-TR) and 3D time-integrated (3D-TI) portal dosimetry in detecting dose discrepancies between the planned and (simulated) delivered dose caused by simulated changes in the anatomy of lung cancer patients. For six lung cancer patients, tumor shift, tumor regression and pleural effusion are simulated by modifying their CT images. Based on the modified CT images, time-integrated (TI) and time-resolved (TR) portal dose images (PDIs) are simulated and 3D-TI doses are calculated. The modified and original PDIs and 3D doses are compared by a gamma analysis with various gamma criteria. Furthermore, the difference in the D 95% (ΔD 95% ) of the GTV is calculated and used as a gold standard. The correlation between the gamma fail rate and the ΔD 95% is investigated, as well the sensitivity and specificity of all combinations of portal dosimetry method, gamma criteria and gamma fail rate threshold. On the individual patient level, there is a correlation between the gamma fail rate and the ΔD 95% , which cannot be found at the group level. The sensitivity and specificity analysis showed that there is not one combination of portal dosimetry method, gamma criteria and gamma fail rate threshold that can detect all simulated anatomical changes. This work shows that it will be more beneficial to relate portal dosimetry and DVH analysis on the patient level, rather than trying to quantify a relationship for a group of patients. With regards to optimizing sensitivity and specificity, different combinations of portal dosimetry method, gamma criteria and gamma fail rate should be used to optimally detect certain types of anatomical changes.

Resource Conservation and Recovery Act permit modifications and the functional equivalency demonstration: a case study

International Nuclear Information System (INIS)

Elsberry, K.; Garcia, P.; Carnes, R.; Kinker, J.; Loehr, C.; Lyon, W.

1996-01-01

Hazardous waste operating permits issued under the Resource Conservation and Recovery Act (RCRA) often impose requirements that specific components and equipment be used. Consequently, changing these items, may first require that the owner/operator request a potentially time-consuming and costly permit modification. However, the owner/operator may demonstrate that a modification is not required because the planned changes are ''functionally equivalent.'' The Controlled-Air Incinerator at Los Alamos National Laboratory is scheduled for maintenance and improvements. The incinerator's carbon adsorption unit/high efficiency particulate air filtration system, was redesigned to improve reliability and minimize maintenance. A study was performed to determine whether the redesigned unit would qualify as functionally equivalent to the original component. In performing this study, the following steps were taken: (a) the key performance factors were identified; (b) performance data describing the existing unit were obtained; (c) performance of both the existing and redesigned units was simulated; and (d) the performance data were compared to ascertain whether the components could qualify as functionally equivalent. In this case, the key performance data included gas residence time and distribution of flow over the activated carbon. Because both units were custom designed and fabricated, a simple comparison of manufacturers' specifications was impossible. Therefore, numerical simulation of each unit design was performed using the TEMPEST thermal-hydraulic computer code to model isothermal hydrodynamic performance under steady-state conditions. The results of residence time calculations from the model were coupled with flow proportion and sampled using a Monte Carlo-style simulation to derive distributions that describe the predicted residence times

Multi-material 3D Models for Temporal Bone Surgical Simulation.

Science.gov (United States)

Rose, Austin S; Kimbell, Julia S; Webster, Caroline E; Harrysson, Ola L A; Formeister, Eric J; Buchman, Craig A

2015-07-01

A simulated, multicolor, multi-material temporal bone model can be created using 3-dimensional (3D) printing that will prove both safe and beneficial in training for actual temporal bone surgical cases. As the process of additive manufacturing, or 3D printing, has become more practical and affordable, a number of applications for the technology in the field of Otolaryngology-Head and Neck Surgery have been considered. One area of promise is temporal bone surgical simulation. Three-dimensional representations of human temporal bones were created from temporal bone computed tomography (CT) scans using biomedical image processing software. Multi-material models were then printed and dissected in a temporal bone laboratory by attending and resident otolaryngologists. A 5-point Likert scale was used to grade the models for their anatomical accuracy and suitability as a simulation of cadaveric and operative temporal bone drilling. The models produced for this study demonstrate significant anatomic detail and a likeness to human cadaver specimens for drilling and dissection. Simulated temporal bones created by this process have potential benefit in surgical training, preoperative simulation for challenging otologic cases, and the standardized testing of temporal bone surgical skills. © The Author(s) 2015.

75 FR 53220 - Adequacy of New Hampshire Municipal Solid Waste Landfill Permit Program

Science.gov (United States)

2010-08-31

...] Adequacy of New Hampshire Municipal Solid Waste Landfill Permit Program AGENCY: Environmental Protection... approved municipal solid waste landfill (MSWLF) program. The approved modification allows the State to..., and demonstration (RD&D) permits to be issued to certain municipal solid waste landfills by approved...

2D and 3D thermal simulations for storage systems with internal natural convection for canistered spent fuel

International Nuclear Information System (INIS)

Yaksh, M.; Wang, C.

2004-01-01

accuracy of the simulation internal to the canister. The actual design of a canistered system inside a concrete cask requires additional modelling effort, since the flow along the external surface of the canister must be included. The target design, however, employs a nonuniform heating of the PWR fuel assemblies, which permits the heat load of an individual PWR assembly to range from.88 kW to 1.35 kW in a zoned configuration. As nonuniform loading adds more complication to the 2D model, an additional confirmation of the 2D modelling methodology may be obtained by performing a three-dimensional (3D) simulation of a simplified version of the target design

Lipid oxidation and vitamin D3 degradation in simulated whole milk powder as influenced by processing and storage.

Science.gov (United States)

Mahmoodani, Fatemeh; Perera, Conrad O; Abernethy, Grant; Fedrizzi, Bruno; Chen, Hong

2018-09-30

Vitamin D3 levels are known to sometimes decline in fortified products, which could be due to its degradation, although the exact mechanism is unknown. In this study, the influence of processing and storage conditions on lipid oxidation and vitamin D3 degradation were studied. Simulated whole milk powders with and without heat treatment were stored for 12 months at two different storage temperatures (20 °C and 40 °C). Stored samples without heat treatment showed higher lipid oxidation products analyzed by PV and TBARS values compared to those with heat treatment. Higher storage temperature also resulted in higher levels of lipid oxidation products. The concentration of vitamin D3 was also analyzed using UHPLC-MS/MS after PTAD derivatization in stored samples. An inverse relationship was observed between lipid oxidation products and vitamin D3 content. Finally, previtamin D3 and vitamin D3 oxidation products were quantified in stored samples using MRM analysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

D Hydrodynamics Simulation of Amazonian Seasonally Flooded Wetlands

Science.gov (United States)

Pinel, S. S.; Bonnet, M. P.; Da Silva, J. S.; Cavalcanti, R., Sr.; Calmant, S.

2016-12-01

In the low Amazonian basin, interactions between floodplains and river channels are important in terms of water exchanges, sediments, or nutrients. These wetlands are considered as hotspot of biodiversity and are among the most productive in the world. However, they are threatened by climatic changes and anthropic activities. Hence, considering the implications for predicting inundation status of floodplain habitats, the strong interactions between water circulation, energy fluxes, biogeochemical and ecological processes, detailed analyses of flooding dynamics are useful and needed. Numerical inundation models offer means to study the interactions among different water sources. Modeling floods events in this area is challenging because flows respond to dynamic hydraulic controls coming from several water sources, complex geomorphology, and vegetation. In addition, due to the difficulty of access, there is a lack of existing hydrological data. In this context, the use of monitoring systems by remote sensing is a good option. In this study, we simulated filling and drainage processes of an Amazon floodplain (Janauacá Lake, AM, Brazil) over a 6 years period (2006-2012). Common approaches of flow modeling in the Amazon region consist of coupling a 1D simulation of the main channel flood wave to a 2D simulation of the inundation of the floodplain. Here, our approach differs as the floodplain is fully simulated. Model used is the 3D model IPH-ECO, which consists of a three-dimensional hydrodynamic module coupled with an ecosystem module. The IPH-ECO hydrodynamic module solves the Reynolds-Averaged Navier-Stokes equations using a semi-implicit discretization. After having calibrated the simulation against roughness coefficients, we validated the model in terms of vertical accuracy against water levels (daily in situ and altimetrics data), in terms of flood extent against inundation maps deduced from available remote-sensed product imagery (ALOS-1/PALSAR.), and in terms

Three-dimensional (3D) printed endovascular simulation models: a feasibility study.

Science.gov (United States)

Mafeld, Sebastian; Nesbitt, Craig; McCaslin, James; Bagnall, Alan; Davey, Philip; Bose, Pentop; Williams, Rob

2017-02-01

Three-dimensional (3D) printing is a manufacturing process in which an object is created by specialist printers designed to print in additive layers to create a 3D object. Whilst there are initial promising medical applications of 3D printing, a lack of evidence to support its use remains a barrier for larger scale adoption into clinical practice. Endovascular virtual reality (VR) simulation plays an important role in the safe training of future endovascular practitioners, but existing VR models have disadvantages including cost and accessibility which could be addressed with 3D printing. This study sought to evaluate the feasibility of 3D printing an anatomically accurate human aorta for the purposes of endovascular training. A 3D printed model was successfully designed and printed and used for endovascular simulation. The stages of development and practical applications are described. Feedback from 96 physicians who answered a series of questions using a 5 point Likert scale is presented. Initial data supports the value of 3D printed endovascular models although further educational validation is required.

The CO_2 emission permits market simulation using Continuous Double Auction

International Nuclear Information System (INIS)

Bartoszczuk, Pawel; Stanczak, Jaroslaw

2016-01-01

In this paper we consider the buying and selling prices of carbon dioxide (CO_2) emission permits in trading models with uncertainty. Permission prices, although usually omitted from standard models, may significantly influence the trading market. We thus construct a more realistic trade model. To do this, we introduced several important changes to the standard model, mainly we added The Continuous Double Action.

Precipitation Processes Developed During ARM (1997), TOGA COARE (1992), GATE (1974), SCSMEX (1998), and KWAJEX (1999): Consistent 2D, Semi-3D and 3D Cloud Resolving Model Simulations

Science.gov (United States)

Tao, W-K.

2003-01-01

Real clouds and cloud systems are inherently three-dimensional (3D). Because of the limitations in computer resources, however, most cloud-resolving models (CRMs) today are still two-dimensional (2D). A few 3D CRMs have been used to study the response of clouds to large-scale forcing. In these 3D simulations, the model domain was small, and the integration time was 6 hours. Only recently have 3D experiments been performed for multi-day periods for tropical cloud systems with large horizontal domains at the National Center for Atmospheric Research (NACAR) and at NASA Goddard Space Flight Center . At Goddard, a 3D Goddard Cumulus Ensemble (GCE) model was used to simulate periods during TOGA COARE, SCSMEX and KWAJEX using 512 by 512 km domain (with 2 km resolution). The results indicate that surface precipitation and latent heating profiles are very similar between the 2D and 3D GCE model simulations. The reason for the strong similarity between the 2D and 3D CRM simulations is that the same observed large-scale advective tendencies of potential temperature, water vapor mixing ratio, and horizontal momentum were used as the main focusing in both the 2D and 3D models. Interestingly, the 2D and 3D versions of the CRM used at CSU showed significant differences in the rainfall and cloud statistics for three ARM cases. The major objectives of this paper are: (1) to assess the performance of the super-parameterization technique, (2) calculate and examine the surface energy (especially radiation) and water budgets, and (3) identify the differences and similarities in the organization and entrainment rates of convection between simulated 2D and 3D cloud systems.

File list: NoD.Adl.20.AllAg.Germline_containing_young_adult [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Adl.20.AllAg.Germline_containing_young_adult ce10 No description Adult Germline containing young adult... http://dbarchive.biosciencedbc.jp/kyushu-u/ce10/assembled/NoD.Adl.20.AllAg.Germline_containing_young_adult.bed ...

File list: NoD.Bld.20.AllAg.Follicular_helper_T_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Bld.20.AllAg.Follicular_helper_T_cells mm9 No description Blood Follicular help...er T cells http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.Bld.20.AllAg.Follicular_helper_T_cells.bed ...

File list: NoD.Emb.20.AllAg.Mitotic_cycle_7-9 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Emb.20.AllAg.Mitotic_cycle_7-9 dm3 No description Embryo Mitotic cycle 7-9 http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/NoD.Emb.20.AllAg.Mitotic_cycle_7-9.bed ...

File list: NoD.Bld.20.AllAg.Peripheral_blood_stem_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Bld.20.AllAg.Peripheral_blood_stem_cells hg19 No description Blood Peripheral b...lood stem cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Bld.20.AllAg.Peripheral_blood_stem_cells.bed ...

File list: NoD.Neu.20.AllAg.Fetal_neural_progenitor_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Neu.20.AllAg.Fetal_neural_progenitor_cells hg19 No description Neural Fetal neural... progenitor cells http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Neu.20.AllAg.Fetal_neural_progenitor_cells.bed ...

3d visualization of atomistic simulations on every desktop

Science.gov (United States)

Peled, Dan; Silverman, Amihai; Adler, Joan

2013-08-01

Once upon a time, after making simulations, one had to go to a visualization center with fancy SGI machines to run a GL visualization and make a movie. More recently, OpenGL and its mesa clone have let us create 3D on simple desktops (or laptops), whether or not a Z-buffer card is present. Today, 3D a la Avatar is a commodity technique, presented in cinemas and sold for home TV. However, only a few special research centers have systems large enough for entire classes to view 3D, or special immersive facilities like visualization CAVEs or walls, and not everyone finds 3D immersion easy to view. For maximum physics with minimum effort a 3D system must come to each researcher and student. So how do we create 3D visualization cheaply on every desktop for atomistic simulations? After several months of attempts to select commodity equipment for a whole room system, we selected an approach that goes back a long time, even predating GL. The old concept of anaglyphic stereo relies on two images, slightly displaced, and viewed through colored glasses, or two squares of cellophane from a regular screen/projector or poster. We have added this capability to our AViz atomistic visualization code in its new, 6.1 version, which is RedHat, CentOS and Ubuntu compatible. Examples using data from our own research and that of other groups will be given.

3d visualization of atomistic simulations on every desktop

International Nuclear Information System (INIS)

Peled, Dan; Silverman, Amihai; Adler, Joan

2013-01-01

Once upon a time, after making simulations, one had to go to a visualization center with fancy SGI machines to run a GL visualization and make a movie. More recently, OpenGL and its mesa clone have let us create 3D on simple desktops (or laptops), whether or not a Z-buffer card is present. Today, 3D a la Avatar is a commodity technique, presented in cinemas and sold for home TV. However, only a few special research centers have systems large enough for entire classes to view 3D, or special immersive facilities like visualization CAVEs or walls, and not everyone finds 3D immersion easy to view. For maximum physics with minimum effort a 3D system must come to each researcher and student. So how do we create 3D visualization cheaply on every desktop for atomistic simulations? After several months of attempts to select commodity equipment for a whole room system, we selected an approach that goes back a long time, even predating GL. The old concept of anaglyphic stereo relies on two images, slightly displaced, and viewed through colored glasses, or two squares of cellophane from a regular screen/projector or poster. We have added this capability to our AViz atomistic visualization code in its new, 6.1 version, which is RedHat, CentOS and Ubuntu compatible. Examples using data from our own research and that of other groups will be given

Single-sided sheet-to-tube spot welding investigated by 3D numerical simulations

DEFF Research Database (Denmark)

Nielsen, Chris Valentin; Chergui, Azeddine; Zhang, Wenqi

The single-sided resistance spot welding process is analyzed by a 3D numerical study of sheet-to-tube joining. Finite element simulations are carried out in SORPAS® 3D. Two levels of electrode force and five levels of welding current are simulated. The overall effects of changing current and force...

3D Modeling and Simulation for Electromagnetic Non-Destructive Testing- Problems and Limitations

International Nuclear Information System (INIS)

Ilham Mukriz Zainal Abidin; Nurul Ain Ahmad Latif

2011-01-01

Non-Destructive Testing (NDT) plays a critical role in nuclear power plants (NPPs) for life cycle management; such testing requires specialists with various NDT related expertise with specific equipment. This paper will discuss the importance of 3D modeling and simulation for electromagnetic NDT for critical and complex components in terms of engineering reasoning and physical trials. Results from simulation are presented which show the link established between the measurements and information relating to defects, such as 3D shape, size and location, which facilitates not only forward problem but also inverse modeling involving experimental system specification and configuration; and pattern recognition for 3D defect information. Subsequently, the problems and limitations pertinent to 3D modeling and simulation are then highlighted and areas of improvement are discussed. (author)

Solar radio emissions: 2D full PIC simulations

Science.gov (United States)

Pierre, H.; Sgattoni, A.; Briand, C.; Amiranoff, F.; Riconda, C.

2016-12-01

Solar radio emissions are electromagnetic waves observed at the local plasma frequency and/or at twice the plasma frequency. To describe their origin a multi-stage model has been proposed by Ginzburg & Zhelezniakov (1958) and further developed by several authors, which consider a succession of non-linear three-wave interaction processes. Electron beams accelerated by solar flares travel in the interplanetary plasma and provide the free energy for the development of plasma instabilities. The model describes how part of the free energy of these beams can be transformed in a succession of plasma waves and eventually into electromagnetic waves. Following the work of Thurgood & Tsiklauri (2015) we performed several 2D Particle In Cell simulations. The simulations follow the entire set of processes from the electron beam propagation in the background plasma to the generation of the electromagnetic waves in particular the 2ωp emission, including the excitation of the low frequency waves. As suggested by Thurgood & Tsiklauri (2015) it is possible to identify regimes where the radiation emission can be directly linked to the electron beams. Our attention was devoted to estimate the conversion efficiency from electron kinetic energy to the em energy, and the growth rate of the several processes which can be identified. We studied the emission angles of the 2ωpradiation and compared them with the theoretical predictions of Willes et. al. (1995). We also show the role played by some numerical parameters i.e. the size and shape of the simulation box. This work is the first step to prepare laser-plasma experiments. V. L. Ginzburg, V. V. Zhelezniakov On the Possible Mechanisms of Sporadic Solar Radio Emission (Radiation in an Isotropic Plasma) Soviet Astronomy, Vol. 2, p.653 (1958) J. O. Thurgood and D. Tsiklauri Self-consistent particle-in-cell simulations of funda- mental and harmonic plasma radio emission mechanisms. Astronomy & Astrophysics 584, A83 (2015). A. Willes, P

Comparison Between 2-D and 3-D Stiffness Matrix Model Simulation of Sasw Inversion for Pavement Structure

Directory of Open Access Journals (Sweden)

Sri Atmaja P. Rosidi

2007-01-01

Full Text Available The Spectral Analysis of Surface Wave (SASW method is a non-destructive in situ seismic technique used to assess and evaluate the material stiffness (dynamic elastic modulus and thickness of pavement layers at low strains. These values can be used analytically to calculate load capacities in order to predict the performance of pavement system. The SASW method is based on the dispersion phenomena of Rayleigh waves in layered media. In order to get the actual shear wave velocities, 2-D and 3-D models are used in the simulation of the inversion process for best fitting between theoretical and empirical dispersion curves. The objective of this study is to simulate and compare the 2-D and 3-D model of SASW analysis in the construction of the theoretical dispersion curve for pavement structure evaluation. The result showed that the dispersion curve from the 3-D model was similar with the dispersion curve of the actual pavement profile compared to the 2-D model. The wave velocity profiles also showed that the 3-D model used in the SASW analysis is able to detect all the distinct layers of flexible pavement units.

Coniferous Canopy BRF Simulation Based on 3-D Realistic Scene

Science.gov (United States)

Wang, Xin-yun; Guo, Zhi-feng; Qin, Wen-han; Sun, Guo-qing

2011-01-01

It is difficulties for the computer simulation method to study radiation regime at large-scale. Simplified coniferous model was investigate d in the present study. It makes the computer simulation methods such as L-systems and radiosity-graphics combined method (RGM) more powerf ul in remote sensing of heterogeneous coniferous forests over a large -scale region. L-systems is applied to render 3-D coniferous forest scenarios: and RGM model was used to calculate BRF (bidirectional refle ctance factor) in visible and near-infrared regions. Results in this study show that in most cases both agreed well. Meanwhiie at a tree and forest level. the results are also good.

Mechanical characterization and numerical modeling of a rotary X-ray anode; Caracterisation mecanique et simulation numerique d'une anode tournante de rayons X

Energy Technology Data Exchange (ETDEWEB)

Lemarchand, G

2003-04-15

This works deals with the design of light rotary anodes used for the generation of X-rays in medical scanners. Such anodes are made of graphite coated with tungsten by low pressure plasma sputtering. The mechanical behaviour of these materials during intense thermo-mechanical solicitation has been studied. In a first step, the in-service conditions of solicitation are defined in terms of excitation frequency, temperature, deformation and deformation velocity. The analysis of used anodes has permitted to define the main modes of in-service damage. Tests were performed on small size samples over the complete temperature range between ambient temperature and 1800 deg. C. Carbon has shown a fragile elastic behaviour while tungsten has shown a more complex behaviour: elastic-fragile up to 400 deg. C, then plastic, and becoming creep sensible above 1200 deg. C. Original load paths have permitted to show the existence of an internal back-stress and a coupling between plastic and viscous deformations. The definition of an original phenomenological law of behaviour with a double inelastic, plastic and visco-plastic deformation and with an interaction term between both flow mechanisms has been necessary to describe the mechanical behaviour of tungsten. The cold-drawing generated by each flow is translated into kinematic variables. The numerical identification of the parameters has been performed using an optimizer coupled to a finite element code which simulates the flexural test. The obtained law has been validated by the experimental observation of paths for complex loads. This behaviour law has been finally used to simulate the conditions of use of a real anode. An axisymmetrical 2-D mesh has permitted to calculate the constraints generated by the post-annealing cooling, by one and several series of radiographies and finally by a complete cooling after use. The repetition of radiographies rapidly leads to stabilized cycles. The calculated stress levels are realistic and

M3D project for simulation studies of plasmas

International Nuclear Information System (INIS)

Park, W.; Belova, E.V.; Fu, G.Y.; Sugiyama, L.E.

1998-01-01

The M3D (Multi-level 3D) project carries out simulation studies of plasmas of various regimes using multi-levels of physics, geometry, and mesh schemes in one code package. This paper and papers by Strauss, Sugiyama, and Belova in this workshop describe the project, and present examples of current applications. The currently available physics models of the M3D project are MHD, two-fluids, gyrokinetic hot particle/MHD hybrid, and gyrokinetic particle ion/two-fluid hybrid models. The code can be run with both structured and unstructured meshes

Analysis of microsatellite markers D18S70 and d20S116 in DNA isolated from dentin: Use in forensic medicine

Directory of Open Access Journals (Sweden)

Puzović Dragana

2009-01-01

Full Text Available Introduction. Short tandem repeats and more specifically microsatellites represent a powerful tool in forensic medicine. In the past years, they have been extensively used in human identification and paternity testing. Objective The aim of the present study was to analyze two microsatellite markers in the Serbian population, i.e. to determine the number of alleles and the relevant forensic parameters. Methods. DNA was isolated from teeth samples using standard proteinase K digestion and phenol/chloroform alcohol extraction. PCR products were analyzed on polyacrilamide gels and visualized by AgNO3 staining. Forensic parameters were calculated using the Cervus software. Results. The loci D18S70 and D20S116 were analyzed on a sample of 70 unrelated, healthy adult individuals from Serbia. The number of alleles was determined and Hardy Weinberg equilibrium was confirmed for both loci. D18S70 and D20S116 demonstrated 6 and 8 alleles, respectively. The power of discrimination (PD and the power of exclusion (PE for the tested STR loci, D18S70 and D20S116 were 0.92 (PD, 0.41 (PE and 0.95 (PD, 0.480 (PE, respectively. Conclusion. According to the presented data, D18S70 and D20S116 are most informative markers. Based on allelic frequencies and statistical parameters for forensic testing, it may be suggested that these two microsatellites represent useful markers for individual identification and parentage analysis in the Serbian population.

Computer simulation of displacement cascade structures in D-T neutron-irradiated Au, Ag, Cu, Ni and Al with the MARLOWE code

International Nuclear Information System (INIS)

Watanabe, N.; Nishiguchi, R.; Shimomura, Y.

1991-01-01

Spatial distribution of point defects in displacement damage cascades at the early stage of their formation was simulated with the MARLOWE code for primary knock-on atoms which is relevant to D-T neutron irradiation. Calculations were carried out for Au, Ag, Cu, Ni and Al. Computer-simulated results were analyzed with complement of TEM observations of D-T neutron-irradiated metals at low temperature. The spatial configuration of displacement cascades, the size of small vacancy aggregates and the size of displacement damage cascade were examined. Results suggest that most of vacancy clusters which were formed in damage cascades may be as small as below 20 vacancies. The remarkable difference in defect yield of cascade damage in Ni and Cu is due to interstitial cluster formation and main contribution of cascade energy overlapping observed in cryotransfer TEM of D-T neutron-irradiated Au is due to ejected interstitials from cascade cores. (orig.)

Nonsequential double ionization of D2 molecules with intense 20-fs pulses

DEFF Research Database (Denmark)

Sakai, H.; Larsen, J.J.; Wendt-Larsen, I.

2003-01-01

The kinetic-energy distribution of D+ fragments obtained from the ionization of D2 molecules with intense 20-fs pulses includes a high-energy component extending up to ˜10 eV. These fragments are only present for linearly, or slightly elliptically, polarized light. Both the maximum kinetic...

Simulation of ultra-high energy photon propagation with PRESHOWER 2.0

Science.gov (United States)

Homola, P.; Engel, R.; Pysz, A.; Wilczyński, H.

2013-05-01

In this paper we describe a new release of the PRESHOWER program, a tool for Monte Carlo simulation of propagation of ultra-high energy photons in the magnetic field of the Earth. The PRESHOWER program is designed to calculate magnetic pair production and bremsstrahlung and should be used together with other programs to simulate extensive air showers induced by photons. The main new features of the PRESHOWER code include a much faster algorithm applied in the procedures of simulating the processes of gamma conversion and bremsstrahlung, update of the geomagnetic field model, and a minor correction. The new simulation procedure increases the flexibility of the code so that it can also be applied to other magnetic field configurations such as, for example, encountered in the vicinity of the sun or neutron stars. Program summaryProgram title: PRESHOWER 2.0 Catalog identifier: ADWG_v2_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADWG_v2_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 3968 No. of bytes in distributed program, including test data, etc.: 37198 Distribution format: tar.gz Programming language: C, FORTRAN 77. Computer: Intel-Pentium based PC. Operating system: Linux or Unix. RAM:probability of the process expected to occur. The new algorithm reduces significantly the number of tracking steps and speeds up the execution of the program. The geomagnetic field model has been updated to IGRF-11, allowing for interpolations up to the year 2015. Numerical Recipes procedures to calculate modified Bessel functions have been replaced with an open source CERN routine DBSKA. One minor bug has been fixed. Restrictions: Gamma conversion into particles other than an electron pair is not considered. Spatial structure of the cascade is neglected. Additional comments

2-D Clinostat for Simulated Microgravity Experiments with Arabidopsis Seedlings

Science.gov (United States)

Wang, Hui; Li, Xugang; Krause, Lars; Görög, Mark; Schüler, Oliver; Hauslage, Jens; Hemmersbach, Ruth; Kircher, Stefan; Lasok, Hanna; Haser, Thomas; Rapp, Katja; Schmidt, Jürgen; Yu, Xin; Pasternak, Taras; Aubry-Hivet, Dorothée; Tietz, Olaf; Dovzhenko, Alexander; Palme, Klaus; Ditengou, Franck Anicet

2016-04-01

Ground-based simulators of microgravity such as fast rotating 2-D clinostats are valuable tools to study gravity related processes. We describe here a versatile g-value-adjustable 2-D clinostat that is suitable for plant analysis. To avoid seedling adaptation to 1 g after clinorotation, we designed chambers that allow rapid fixation. A detailed protocol for fixation, RNA isolation and the analysis of selected genes is described. Using this clinostat we show that mRNA levels of LONG HYPOCOTYL 5 (HY5), MIZU-KUSSEI 1 (MIZ1) and microRNA MIR163 are down-regulated in 5-day-old Arabidopsis thaliana roots after 3 min and 6 min of clinorotation using a maximal reduced g-force of 0.02 g, hence demonstrating that this 2-D clinostat enables the characterization of early transcriptomic events during root response to microgravity. We further show that this 2-D clinostat is able to compensate the action of gravitational force as both gravitropic-dependent statolith sedimentation and subsequent auxin redistribution (monitoring D R5 r e v :: G F P reporter) are abolished when plants are clinorotated. Our results demonstrate that 2-D clinostats equipped with interchangeable growth chambers and tunable rotation velocity are suitable for studying how plants perceive and respond to simulated microgravity.

Comparison of CT-based 3D treatment planning with simulator planning of pelvic irradiation of primary cervical carcinoma

International Nuclear Information System (INIS)

Knocke, T.H.; Pokrajac, B.; Fellner, C.; Poetter, R.

1999-01-01

In a prospective study on 20 subsequent patients with primary cervical carcinoma in Stages I to III simulator planning of a 4-field box-technique was performed. After defining the planning target volume (PTV) in the 3D planning system the field configuration of the simulator planning was transmitted. The resulting plan was compared to a second one based on the defined PTV and evaluated regarding a possible geographical miss and encompassment of the PTV by the treated volume (ICRU). Volumes of open and shaped portals were calculated for both techniques. Planning by simulation resulted in 1 geographical miss and in 10 more cases the encompassment of the PTV by the treated volume was inadequate. For a PTV of mean 1 729 cm 3 the mean volume defined by simulation was 3 120 cm 3 for the open portals and 2 702 cm 3 for the shaped portals. The volume reduction by blocks was 13,4% (mean). With CT-based 3D treatment planning the volume of the open portals was 3,3% (mean) enlarged to 3 224 cm 3 . The resulting mean volume of the shaped portals was 2 458 ccm. The reduction compared to the open portals was 23,8% (mean). The treated volumes were 244 cm 3 or 9% (mean) smaller compared to simulator planning. The 'treated volume/planning target volume ratio' was decreased from 1.59 to 1.42. (orig.) [de

Comparison of 2D simulations of detached divertor plasmas with divertor Thomson measurements in the DIII-D tokamak

Directory of Open Access Journals (Sweden)

T.D. Rognlien

2017-08-01

Full Text Available A modeling study is reported using new 2D data from DIII-D tokamak divertor plasmas and improved 2D transport model that includes large cross-field drifts for the numerically difficult low anomalous transport regime associated with the H-mode. The data set, which spans a range of plasma densities for both forward and reverse toroidal magnetic field (Bt, is provided by divertor Thomson scattering (DTS. Measurements utilizing X-point sweeping give corresponding 2D profiles of electron temperature (Te and density (ne across both divertor legs for individual discharges. The simulations focus on the open magnetic field-line regions, though they also include a small region of closed field lines. The calculations show the same features of in/out divertor plasma asymmetries as measured in the experiment, with the normal Bt direction (ion ∇B drift toward the X-point having higher ne and lower Te in the inner divertor leg than outer. Corresponding emission data for total radiated power shows a strong inner-divertor/outer-divertor asymmetry that is reproduced by the simulations. These 2D UEDGE transport simulations are enabled for steep-gradient H-mode conditions by newly implemented algorithms to control isolated grid-scale irregularities.

Offshore Wind Energy Permitting: A Survey of U.S. Project Developers

Energy Technology Data Exchange (ETDEWEB)

Van Cleve, Frances B.; Copping, Andrea E.

2010-11-30

The U.S. Department of Energy (DOE) has adopted a goal to generate 20% of the nation’s electricity from wind power by 2030. Achieving this “20% Wind Scenario” in 2030 requires acceleration of the current rate of wind project development. Offshore wind resources contribute substantially to the nation’s wind resource, yet to date no offshore wind turbines have been installed in the U.S. Progress developing offshore wind projects has been slowed by technological challenges, uncertainties about impacts to the marine environment, siting and permitting challenges, and viewshed concerns. To address challenges associated with siting and permitting, Pacific Northwest National Laboratory (PNNL) surveyed offshore wind project developers about siting and project development processes, their experience with the environmental permitting process, and the role of coastal and marine spatial planning (CMSP) in development of the offshore wind industry. Based on the responses to survey questions, we identify several priority recommendations to support offshore wind development. Recommendations also include considerations for developing supporting industries in the U.S. and how to use Coastal and Marine Spatial Planning (CMSP) to appropriately consider ocean energy among existing ocean uses. In this report, we summarize findings, discuss the implications, and suggest actions to improve the permitting and siting process.

The Polarization Signature of Photospheric Magnetic Fields in 3D MHD Simulations and Observations at Disk Center

Energy Technology Data Exchange (ETDEWEB)

Beck, C. [National Solar Observatory, 3665 Discovery Drive, Boulder, CO 80303 (United States); Fabbian, D. [Max-Planck-Institut für Sonnensytemforschung, Justus-von-Liebig-Weg 3, D-37077 Göttingen (Germany); Rezaei, R. [Instituto de Astrofísica de Canarias, C/Vía Láctea S/N, E-38205 La Laguna, Tenerife (Spain); Puschmann, K. G., E-mail: cbeck@nso.edu [Alzenau (Germany)

2017-06-10

Before using three-dimensional (3D) magnetohydrodynamical (MHD) simulations of the solar photosphere in the determination of elemental abundances, one has to ensure that the correct amount of magnetic flux is present in the simulations. The presence of magnetic flux modifies the thermal structure of the solar photosphere, which affects abundance determinations and the solar spectral irradiance. The amount of magnetic flux in the solar photosphere also constrains any possible heating in the outer solar atmosphere through magnetic reconnection. We compare the polarization signals in disk-center observations of the solar photosphere in quiet-Sun regions with those in Stokes spectra computed on the basis of 3D MHD simulations having average magnetic flux densities of about 20, 56, 112, and 224 G. This approach allows us to find the simulation run that best matches the observations. The observations were taken with the Hinode SpectroPolarimeter (SP), the Tenerife Infrared Polarimeter (TIP), the Polarimetric Littrow Spectrograph (POLIS), and the GREGOR Fabry–Pèrot Interferometer (GFPI), respectively. We determine characteristic quantities of full Stokes profiles in a few photospheric spectral lines in the visible (630 nm) and near-infrared (1083 and 1565 nm). We find that the appearance of abnormal granulation in intensity maps of degraded simulations can be traced back to an initially regular granulation pattern with numerous bright points in the intergranular lanes before the spatial degradation. The linear polarization signals in the simulations are almost exclusively related to canopies of strong magnetic flux concentrations and not to transient events of magnetic flux emergence. We find that the average vertical magnetic flux density in the simulation should be less than 50 G to reproduce the observed polarization signals in the quiet-Sun internetwork. A value of about 35 G gives the best match across the SP, TIP, POLIS, and GFPI observations.

Caractérisation et simulation des mouvements d'atteinte par un opérateur humain en position assise en vue d'applications ergonomiques

OpenAIRE

CHEVALOT, N

2006-01-01

La simulation de mouvements d'atteinte effectués par un opérateur assis est particulièrement utile pour les constructeurs d'automobiles. Elle permet d'améliorer l'ergonomie de l'habitacle et des commandes, le plus en amont possible dans la conception. Elle consiste à simuler un mouvement et à prédire son inconfort. Cependant, ce type de simulation se heurte à des problèmes pratiques et théoriques. Pour la partie pratique, une méthode de simulation générique et stable pour tout type de mouveme...

Investigation the performance of 0-D and 3-d combustion simulation softwares for modelling HCCI engine with high air excess ratios

Directory of Open Access Journals (Sweden)

Gökhan Coşkun

2017-10-01

Full Text Available In this study, performance of zero and three dimensional simulations codes that used for simulate a homogenous charge compression ignition (HCCI engine fueled with Primary Reference Fuel PRF (85% iso-octane and 15% n-heptane were investigated. 0-D code, called as SRM Suite (Stochastic Reactor Model which can simulate engine combustion by using stochastic reactor model technique were used. Ansys-Fluent which can simulate computational fluid dynamics (CFD was used for 3-D engine combustion simulations. Simulations were evaluated for both commercial codes in terms of combustion, heat transfer and emissions in a HCCI engine. Chemical kinetic mechanisms which developed by Tsurushima including 33 species and 38 reactions for surrogate PRF fuel were used for combustion simulations. Analysis showed that both codes have advantages over each other.

Modelling and Manufacturing of a 3D Printed Trachea for Cricothyroidotomy Simulation.

Science.gov (United States)

Doucet, Gregory; Ryan, Stephen; Bartellas, Michael; Parsons, Michael; Dubrowski, Adam; Renouf, Tia

2017-08-18

Cricothyroidotomy is a life-saving medical procedure that allows for tracheal intubation. Most current cricothyroidotomy simulation models are either expensive or not anatomically accurate and provide the learner with an unrealistic simulation experience. The goal of this project is to improve current simulation techniques by utilizing rapid prototyping using 3D printing technology and expert opinions to develop inexpensive and anatomically accurate trachea simulators. In doing so, emergency cricothyroidotomy simulation can be made accessible, accurate, cost-effective and reproducible. Three-dimensional modelling software was used in conjunction with a desktop three-dimensional (3D) printer to design and manufacture an anatomically accurate model of the cartilage within the trachea (thyroid cartilage, cricoid cartilage, and the tracheal rings). The initial design was based on dimensions found in studies of tracheal anatomical configuration. This ensured that the landmarking necessary for emergency cricothyroidotomies was designed appropriately. Several revisions of the original model were made based on informal opinion from medical professionals to establish appropriate anatomical accuracy of the model for use in rural/remote cricothyroidotomy simulation. Using an entry-level desktop 3D printer, a low cost tracheal model was successfully designed that can be printed in less than three hours for only $1.70 Canadian dollars (CAD). Due to its anatomical accuracy, flexibility and durability, this model is great for use in emergency medicine simulation training. Additionally, the model can be assembled in conjunction with a membrane to simulate tracheal ligaments. Skin has been simulated as well to enhance the realism of the model. The result is an accurate simulation that will provide users with an anatomically correct model to practice important skills used in emergency airway surgery, specifically landmarking, incision and intubation. This design is a novel and easy

Benchmarking the mesoscale variability in global ocean eddy-permitting numerical systems

Science.gov (United States)

Cipollone, Andrea; Masina, Simona; Storto, Andrea; Iovino, Doroteaciro

2017-10-01

The role of data assimilation procedures on representing ocean mesoscale variability is assessed by applying eddy statistics to a state-of-the-art global ocean reanalysis (C-GLORS), a free global ocean simulation (performed with the NEMO system) and an observation-based dataset (ARMOR3D) used as an independent benchmark. Numerical results are computed on a 1/4 ∘ horizontal grid (ORCA025) and share the same resolution with ARMOR3D dataset. This "eddy-permitting" resolution is sufficient to allow ocean eddies to form. Further to assessing the eddy statistics from three different datasets, a global three-dimensional eddy detection system is implemented in order to bypass the need of regional-dependent definition of thresholds, typical of commonly adopted eddy detection algorithms. It thus provides full three-dimensional eddy statistics segmenting vertical profiles from local rotational velocities. This criterion is crucial for discerning real eddies from transient surface noise that inevitably affects any two-dimensional algorithm. Data assimilation enhances and corrects mesoscale variability on a wide range of features that cannot be well reproduced otherwise. The free simulation fairly reproduces eddies emerging from western boundary currents and deep baroclinic instabilities, while underestimates shallower vortexes that populate the full basin. The ocean reanalysis recovers most of the missing turbulence, shown by satellite products , that is not generated by the model itself and consistently projects surface variability deep into the water column. The comparison with the statistically reconstructed vertical profiles from ARMOR3D show that ocean data assimilation is able to embed variability into the model dynamics, constraining eddies with in situ and altimetry observation and generating them consistently with local environment.

3D Surgical Simulation

Science.gov (United States)

Cevidanes, Lucia; Tucker, Scott; Styner, Martin; Kim, Hyungmin; Chapuis, Jonas; Reyes, Mauricio; Proffit, William; Turvey, Timothy; Jaskolka, Michael

2009-01-01

This paper discusses the development of methods for computer-aided jaw surgery. Computer-aided jaw surgery allows us to incorporate the high level of precision necessary for transferring virtual plans into the operating room. We also present a complete computer-aided surgery (CAS) system developed in close collaboration with surgeons. Surgery planning and simulation include construction of 3D surface models from Cone-beam CT (CBCT), dynamic cephalometry, semi-automatic mirroring, interactive cutting of bone and bony segment repositioning. A virtual setup can be used to manufacture positioning splints for intra-operative guidance. The system provides further intra-operative assistance with the help of a computer display showing jaw positions and 3D positioning guides updated in real-time during the surgical procedure. The CAS system aids in dealing with complex cases with benefits for the patient, with surgical practice, and for orthodontic finishing. Advanced software tools for diagnosis and treatment planning allow preparation of detailed operative plans, osteotomy repositioning, bone reconstructions, surgical resident training and assessing the difficulties of the surgical procedures prior to the surgery. CAS has the potential to make the elaboration of the surgical plan a more flexible process, increase the level of detail and accuracy of the plan, yield higher operative precision and control, and enhance documentation of cases. Supported by NIDCR DE017727, and DE018962 PMID:20816308

A 3D virtual reality simulator for training of minimally invasive surgery.

Science.gov (United States)

Mi, Shao-Hua; Hou, Zeng-Gunag; Yang, Fan; Xie, Xiao-Liang; Bian, Gui-Bin

2014-01-01

For the last decade, remarkable progress has been made in the field of cardiovascular disease treatment. However, these complex medical procedures require a combination of rich experience and technical skills. In this paper, a 3D virtual reality simulator for core skills training in minimally invasive surgery is presented. The system can generate realistic 3D vascular models segmented from patient datasets, including a beating heart, and provide a real-time computation of force and force feedback module for surgical simulation. Instruments, such as a catheter or guide wire, are represented by a multi-body mass-spring model. In addition, a realistic user interface with multiple windows and real-time 3D views are developed. Moreover, the simulator is also provided with a human-machine interaction module that gives doctors the sense of touch during the surgery training, enables them to control the motion of a virtual catheter/guide wire inside a complex vascular model. Experimental results show that the simulator is suitable for minimally invasive surgery training.

Precipitation Processes Developed During ARM (1997), TOGA COARE (1992) GATE (1974), SCSMEX (1998), and KWAJEX (1999): Consistent 3D, Semi-3D and 3D Cloud Resolving Model Simulations

Science.gov (United States)

Tao, W.-K.; Hou, A.; Atlas, R.; Starr, D.; Sud, Y.

2003-01-01

Real clouds and cloud systems are inherently three-dimensional (3D). Because of the limitations in computer resources, however, most cloud-resolving models (CRMs) today are still two-dimensional (2D) have been used to study the response of clouds to large-scale forcing. IN these 3D simulators, the model domain was small, and the integration time was 6 hours. Only recently have 3D experiments been performed for multi-day periods for tropical clouds systems with large horizontal domains at the National Center of Atmospheric Research (NCAR) and at NASA Goddard Space Center. At Goddard, a 3D cumulus Ensemble (GCE) model was used to simulate periods during TOGA COARE, GATE, SCSMEX, ARM, and KWAJEX using a 512 by 512 km domain (with 2-km resolution). The result indicate that surface precipitation and latent heating profiles are very similar between the 2D and 3D GCE model simulation. The major objective of this paper are: (1) to assess the performance of the super-parametrization technique, (2) calculate and examine the surface energy (especially radiation) and water budget, and (3) identify the differences and similarities in the organization and entrainment rates of convection between simulated 2D and 3D cloud systems.

Analysis of PKP scattering using mantle mixing simulations and axisymmetric 3D waveforms

Science.gov (United States)

Haugland, Samuel M.; Ritsema, Jeroen; van Keken, Peter E.; Nissen-Meyer, Tarje

2018-03-01

The scattering of PKP waves in the lower mantle produces isolated signals before the PKIKP phase. We explore whether these so-called PKIKP precursors can be related to wave scattering off mid ocean ridge basalt (MORB) fragments that have been advected in the deep mantle throughout geologic time. We construct seismic models of small-scale (>20 km) heterogeneity in the lower mantle informed by mantle mixing simulations from Brandenburg et al. (2008) and generate PKIKP precursors using 3D, axisymmetric waveform simulations up to 0.75 Hz. We consider two end-member geodynamic models with fundamentally different distributions of MORB in the lower mantle. Our results suggest that the accumulation of MORB at the base of the mantle is a viable hypothesis for the origin of PKP scattering. We find that the strength of the PKIKP precursor amplitudes is consistent with P wave speed heterogeneity of 0.1-0.2%, as reported previously. The radial distribution of MORB has a profound effect on the strength of PKIKP precursors. Simulation of PKIKP precursors for models with an increasing MORB concentration in the lowermost 500 km of the mantle appears to reproduce most accurately the strength of PKIKP precursors in Global Seismic Network waveforms. These models assume that MORB has an excess density of at least 7%. Additional simulations of more complex geodynamic models will better constrain the geodynamic conditions to explain the significant variability of PKP scattering strength.

GPU accelerated simulations of 3D deterministic particle transport using discrete ordinates method

International Nuclear Information System (INIS)

Gong Chunye; Liu Jie; Chi Lihua; Huang Haowei; Fang Jingyue; Gong Zhenghu

2011-01-01

Graphics Processing Unit (GPU), originally developed for real-time, high-definition 3D graphics in computer games, now provides great faculty in solving scientific applications. The basis of particle transport simulation is the time-dependent, multi-group, inhomogeneous Boltzmann transport equation. The numerical solution to the Boltzmann equation involves the discrete ordinates (S n ) method and the procedure of source iteration. In this paper, we present a GPU accelerated simulation of one energy group time-independent deterministic discrete ordinates particle transport in 3D Cartesian geometry (Sweep3D). The performance of the GPU simulations are reported with the simulations of vacuum boundary condition. The discussion of the relative advantages and disadvantages of the GPU implementation, the simulation on multi GPUs, the programming effort and code portability are also reported. The results show that the overall performance speedup of one NVIDIA Tesla M2050 GPU ranges from 2.56 compared with one Intel Xeon X5670 chip to 8.14 compared with one Intel Core Q6600 chip for no flux fixup. The simulation with flux fixup on one M2050 is 1.23 times faster than on one X5670.

GPU accelerated simulations of 3D deterministic particle transport using discrete ordinates method

Science.gov (United States)

Gong, Chunye; Liu, Jie; Chi, Lihua; Huang, Haowei; Fang, Jingyue; Gong, Zhenghu

2011-07-01

Graphics Processing Unit (GPU), originally developed for real-time, high-definition 3D graphics in computer games, now provides great faculty in solving scientific applications. The basis of particle transport simulation is the time-dependent, multi-group, inhomogeneous Boltzmann transport equation. The numerical solution to the Boltzmann equation involves the discrete ordinates ( Sn) method and the procedure of source iteration. In this paper, we present a GPU accelerated simulation of one energy group time-independent deterministic discrete ordinates particle transport in 3D Cartesian geometry (Sweep3D). The performance of the GPU simulations are reported with the simulations of vacuum boundary condition. The discussion of the relative advantages and disadvantages of the GPU implementation, the simulation on multi GPUs, the programming effort and code portability are also reported. The results show that the overall performance speedup of one NVIDIA Tesla M2050 GPU ranges from 2.56 compared with one Intel Xeon X5670 chip to 8.14 compared with one Intel Core Q6600 chip for no flux fixup. The simulation with flux fixup on one M2050 is 1.23 times faster than on one X5670.

Monte Carlo Simulation on Compensated Neutron Porosity Logging in LWD With D-T Pulsed Neutron Generator

International Nuclear Information System (INIS)

Zhang Feng; Hou Shuang; Jin Xiuyun

2010-01-01

The process of neutron interaction induced by D-T pulsed neutron generator and 241 Am-Be source was simulated by using Monte Carlo method. It is concluded that the thermal neutron count descend exponentially as the spacing increasing. The smaller porosity was, the smaller the differences between the two sources were. When the porosity reached 40%, the ratio of thermal neutron count generated by D-T pulsed neutron source was much larger than that generated by 241 Am-Be neutron source, and its distribution range was wider. The near spacing selected was 20-30 cm, and that of far spacing was about 60-70 cm. The detection depth by using D-T pulsed neutron source was almost unchanged under condition of the same sapcing, and the sensitivity of measurement to the formation porosity decreases. The results showed that it can not only guarantee the statistic of count, but also improve detection sensitivity and depth at the same time of increasing spacing. Therefore, 241 Am-Be neutron source can be replaced by D-T neutron tube in LWD tool. (authors)

Numerical Simulation of 3-D Wave Crests

Institute of Scientific and Technical Information of China (English)

YU Dingyong; ZHANG Hanyuan

2003-01-01

A clear definition of 3-D wave crest and a description of the procedures to detect the boundary of wave crest are presented in the paper. By using random wave theory and directional wave spectrum, a MATLAB-platformed program is designed to simulate random wave crests for various directional spectral conditions in deep water. Statistics of wave crests with different directional spreading parameters and different directional functions are obtained and discussed.

Survival of Lactobacillus delbrueckii UFV H2b20 in fermented milk under simulated gastric and intestinal conditions.

Science.gov (United States)

da Conceição, L L; Leandro, E S; Freitas, F S; de Oliveira, M N V; Ferreira-Machado, A B; Borges, A C; de Moraes, C A

2013-09-01

The survival of Lactobacillus delbrueckii UFV H2b20 was assessed in fermented milk, both during the storage period and after exposure to simulated gastric and intestinal juices, as well the detection of the gene fbpA involved in adherence to human gastrointestinal tract. L. delbrueckii UFV H2b20 remained stable and viable for 28 days under refrigerated storage conditions. After one day of storage, that strain exhibited a one-log population reduction following exposure in tandem to simulated gastric and intestinal juices. After 14 days of storage, a two-log reduction was observed following 90 min of exposure to the simulated gastric conditions. However, the strain did not survive following exposure to the simulated intestinal juice. The observed tolerance to storage conditions and resistance to the simulated gastric and intestinal conditions confirm the potential use of L. delbrueckii UFV H2b20 as a probiotic, which is further reinforced by the detection of fbpA in this strain.

RTS amplitudes in decananometer MOSFETs: 3-D simulation study

OpenAIRE

Asenov, A.; Balasubramaniam, R.; Brown, A.R.; Davies, J.H.

2003-01-01

In this paper we study the amplitudes of random telegraph signals (RTS) associated with the trapping of a single electron in defect states at the Si/SiO/sub 2/ interface of sub-100-nm (decananometer) MOSFETs employing three-dimensional (3-D) "atomistic" simulations. Both continuous doping charge and random discrete dopants in the active region of the MOSFETs are considered in the simulations. The dependence of the RTS amplitudes on the position of the trapped charge in the channel and on devi...

Simple 3-D stimulus for motion parallax and its simulation.

Science.gov (United States)

Ono, Hiroshi; Chornenkyy, Yevgen; D'Amour, Sarah

2013-01-01

Simulation of a given stimulus situation should produce the same perception as the original. Rogers et al (2009 Perception 38 907-911) simulated Wheeler's (1982, PhD thesis, Rutgers University, NJ) motion parallax stimulus and obtained quite different perceptions. Wheeler's observers were unable to reliably report the correct direction of depth, whereas Rogers's were. With three experiments we explored the possible reasons for the discrepancy. Our results suggest that Rogers was able to see depth from the simulation partly due to his experience seeing depth with random dot surfaces.

Mechanical characterization and numerical modeling of a rotary X-ray anode; Caracterisation mecanique et simulation numerique d'une anode tournante de rayons X

Energy Technology Data Exchange (ETDEWEB)

Lemarchand, G

2003-04-15

This works deals with the design of light rotary anodes used for the generation of X-rays in medical scanners. Such anodes are made of graphite coated with tungsten by low pressure plasma sputtering. The mechanical behaviour of these materials during intense thermo-mechanical solicitation has been studied. In a first step, the in-service conditions of solicitation are defined in terms of excitation frequency, temperature, deformation and deformation velocity. The analysis of used anodes has permitted to define the main modes of in-service damage. Tests were performed on small size samples over the complete temperature range between ambient temperature and 1800 deg. C. Carbon has shown a fragile elastic behaviour while tungsten has shown a more complex behaviour: elastic-fragile up to 400 deg. C, then plastic, and becoming creep sensible above 1200 deg. C. Original load paths have permitted to show the existence of an internal back-stress and a coupling between plastic and viscous deformations. The definition of an original phenomenological law of behaviour with a double inelastic, plastic and visco-plastic deformation and with an interaction term between both flow mechanisms has been necessary to describe the mechanical behaviour of tungsten. The cold-drawing generated by each flow is translated into kinematic variables. The numerical identification of the parameters has been performed using an optimizer coupled to a finite element code which simulates the flexural test. The obtained law has been validated by the experimental observation of paths for complex loads. This behaviour law has been finally used to simulate the conditions of use of a real anode. An axisymmetrical 2-D mesh has permitted to calculate the constraints generated by the post-annealing cooling, by one and several series of radiographies and finally by a complete cooling after use. The repetition of radiographies rapidly leads to stabilized cycles. The calculated stress levels are realistic and

Rigid body motion in stereo 3D simulation

International Nuclear Information System (INIS)

Zabunov, Svetoslav

2010-01-01

This paper addresses the difficulties experienced by first-grade students studying rigid body motion at Sofia University. Most quantities describing the rigid body are in relations that the students find hard to visualize and understand. They also lose the notion of cause-result relations between vector quantities, such as the relation between torque and angular momentum. Consequently, the understanding of physical laws and conservation principles in free rigid body motion is hampered. This paper presents the capabilities of a 3D simulation, which aims to clarify these questions to the students, who are taught mechanics in the general physics course. The rigid body motion simulations may be observed at http://ialms.net/sim/, and are intended to complement traditional learning practices, not replace them, as the author shares the opinion that no simulation may fully resemble reality.

Parameterization experiments performed via synthetic mass movements prototypes generated by 3D slope stability simulator

Science.gov (United States)

Colangelo, Antonio C.

2010-05-01

The central purpose of this work is to perform a reverse procedure in the mass movement conventional parameterization approach. The idea is to generate a number of synthetic mass movements by means of the "slope stability simulator" (Colangelo, 2007), and compeer their morphological and physical properties with "real" conditions of effective mass movements. This device is an integrated part of "relief unity emulator" (rue), that permits generate synthetic mass movements in a synthetic slope environment. The "rue" was build upon fundamental geomorphological concepts. These devices operate with an integrated set of mechanical, geomorphic and hydrological models. The "slope stability simulator" device (sss) permits to perform a detailed slope stability analysis in a theoretical three dimensional space, by means of evaluation the spatial behavior of critical depths, gradients and saturation levels in the "potential rupture surfaces" inferred along a set of slope profiles, that compounds a synthetic slope unity. It's a meta-stable 4-dimensional object generated by means of "rue", that represents a sequence evolution of a generator profile applied here, was adapted the infinite slope model for slope. Any slope profiles were sliced by means of finite element solution like in Bishop method. For the synthetic slope systems generated, we assume that the potential rupture surface occurs at soil-regolith or soil-rock boundary in slope material. Sixteen variables were included in the "rue-sss" device that operates in an integrated manner. For each cell, the factor of safety was calculated considering the value of shear strength (cohesion and friction) of material, soil-regolith boundary depth, soil moisture level content, potential rupture surface gradient, slope surface gradient, top of subsurface flow gradient, apparent soil bulk density and vegetation surcharge. The slope soil was considered as cohesive material. The 16 variables incorporated in the models were analyzed for

Simulation of Flow, Sediment Transport, and Sediment Mobility of the Lower Coeur d'Alene River, Idaho

Science.gov (United States)

Berenbrock, Charles; Tranmer, Andrew W.

2008-01-01

A one-dimensional sediment-transport model and a multi-dimensional hydraulic and bed shear stress model were developed to investigate the hydraulic, sediment transport, and sediment mobility characteristics of the lower Coeur d?Alene River in northern Idaho. This report documents the development and calibration of those models, as well as the results of model simulations. The one-dimensional sediment-transport model (HEC-6) was developed, calibrated, and used to simulate flow hydraulics and erosion, deposition, and transport of sediment in the lower Coeur d?Alene River. The HEC-6 modeled reach, comprised of 234 cross sections, extends from Enaville, Idaho, on the North Fork of the Coeur d?Alene River and near Pinehurst, Idaho, on the South Fork of the river to near Harrison, Idaho, on the main stem of the river. Bed-sediment samples collected by previous investigators and samples collected for this study in 2005 were used in the model. Sediment discharge curves from a previous study were updated using suspended-sediment samples collected at three sites since April 2000. The HEC-6 was calibrated using river discharge and water-surface elevations measured at five U.S. Geological Survey gaging stations. The calibrated HEC-6 model allowed simulation of management alternatives to assess erosion and deposition from proposed dredging of contaminated streambed sediments in the Dudley reach. Four management alternatives were simulated with HEC-6. Before the start of simulation for these alternatives, seven cross sections in the reach near Dudley, Idaho, were deepened 20 feet?removing about 296,000 cubic yards of sediments?to simulate dredging. Management alternative 1 simulated stage-discharge conditions from 2000, and alternative 2 simulated conditions from 1997. Results from alternatives 1 and 2 indicated that about 6,500 and 12,300 cubic yards, respectively, were deposited in the dredged reach. These figures represent 2 and 4 percent, respectively, of the total volume of

Prototype Development Capabilities of 3D Spatial Interactions and Failures During Scenario Simulation

Energy Technology Data Exchange (ETDEWEB)

Steven Prescott; Ramprasad Sampath; Curtis Smith; Tony Koonce

2014-09-01

Computers have been used for 3D modeling and simulation, but only recently have computational resources been able to give realistic results in a reasonable time frame for large complex models. This report addressed the methods, techniques, and resources used to develop a prototype for using 3D modeling and simulation engine to improve risk analysis and evaluate reactor structures and components for a given scenario. The simulations done for this evaluation were focused on external events, specifically tsunami floods, for a hypothetical nuclear power facility on a coastline.

Multi-physic simulations of irradiation experiments in a technological irradiation reactor; Modelisation pluridisciplinaire d'experiences d'irradiation dans un reacteur d'irradiation technologique

Energy Technology Data Exchange (ETDEWEB)

Bonaccorsi, Th

2007-09-15

A Material Testing Reactor (MTR) makes it possible to irradiate material samples under intense neutron and photonic fluxes. These experiments are carried out in experimental devices localised in the reactor core or in periphery (reflector). Available physics simulation tools only treat, most of the time, one physics field in a very precise way. Multi-physic simulations of irradiation experiments therefore require a sequential use of several calculation codes and data exchanges between these codes: this corresponds to problems coupling. In order to facilitate multi-physic simulations, this thesis sets up a data model based on data-processing objects, called Technological Entities. This data model is common to all of the physics fields. It permits defining the geometry of an irradiation device in a parametric way and to associate information about materials to it. Numerical simulations are encapsulated into interfaces providing the ability to call specific functionalities with the same command (to initialize data, to launch calculations, to post-treat, to get results,... ). Thus, once encapsulated, numerical simulations can be re-used for various studies. This data model is developed in a SALOME platform component. The first application case made it possible to perform neutronic simulations (OSIRIS reactor and RJH) coupled with fuel behavior simulations. In a next step, thermal hydraulics could also be taken into account. In addition to the improvement of the calculation accuracy due to the physical phenomena coupling, the time spent in the development phase of the simulation is largely reduced and the possibilities of uncertainty treatment are under consideration. (author)

Isotachophoresis of proteins in a networked microfluidic chip: experiment and 2-D simulation.

Science.gov (United States)

Cui, Huanchun; Dutta, Prashanta; Ivory, Cornelius F

2007-04-01

This paper reports both the experimental application and 2-D simulation of ITP of proteins in a networked microfluidic chip. Experiments demonstrate that a mixture of three fluorescent proteins can be concentrated and stacked into adjacent zones of pure protein under a constant voltage of 100 V over a 2 cm long microchannel. Measurements of the isotachophoretic velocity of the moving zones demonstrates that, during ITP under a constant voltage, the zone velocity decreases as more of the channel is occupied by the terminating electrolyte. A 2-D ITP model based on the Nernst-Planck equations illustrates the stacking and separation features of ITP using simulations of three virtual proteins. The self-sharpening behavior of ITP zones dispersed by a T-junction is clearly demonstrated both by experiment and by simulation. Comparison of 2-D simulations of ITP and zone electrophoresis (ZE) confirms that ZE lacks the ability to resharpen protein zones after they pass through a T-junction.

An Object-Oriented Simulator for 3D Digital Breast Tomosynthesis Imaging System

Directory of Open Access Journals (Sweden)

Saeed Seyyedi

2013-01-01

Full Text Available Digital breast tomosynthesis (DBT is an innovative imaging modality that provides 3D reconstructed images of breast to detect the breast cancer. Projections obtained with an X-ray source moving in a limited angle interval are used to reconstruct 3D image of breast. Several reconstruction algorithms are available for DBT imaging. Filtered back projection algorithm has traditionally been used to reconstruct images from projections. Iterative reconstruction algorithms such as algebraic reconstruction technique (ART were later developed. Recently, compressed sensing based methods have been proposed in tomosynthesis imaging problem. We have developed an object-oriented simulator for 3D digital breast tomosynthesis (DBT imaging system using C++ programming language. The simulator is capable of implementing different iterative and compressed sensing based reconstruction methods on 3D digital tomosynthesis data sets and phantom models. A user friendly graphical user interface (GUI helps users to select and run the desired methods on the designed phantom models or real data sets. The simulator has been tested on a phantom study that simulates breast tomosynthesis imaging problem. Results obtained with various methods including algebraic reconstruction technique (ART and total variation regularized reconstruction techniques (ART+TV are presented. Reconstruction results of the methods are compared both visually and quantitatively by evaluating performances of the methods using mean structural similarity (MSSIM values.

An object-oriented simulator for 3D digital breast tomosynthesis imaging system.

Science.gov (United States)

Seyyedi, Saeed; Cengiz, Kubra; Kamasak, Mustafa; Yildirim, Isa

2013-01-01

Digital breast tomosynthesis (DBT) is an innovative imaging modality that provides 3D reconstructed images of breast to detect the breast cancer. Projections obtained with an X-ray source moving in a limited angle interval are used to reconstruct 3D image of breast. Several reconstruction algorithms are available for DBT imaging. Filtered back projection algorithm has traditionally been used to reconstruct images from projections. Iterative reconstruction algorithms such as algebraic reconstruction technique (ART) were later developed. Recently, compressed sensing based methods have been proposed in tomosynthesis imaging problem. We have developed an object-oriented simulator for 3D digital breast tomosynthesis (DBT) imaging system using C++ programming language. The simulator is capable of implementing different iterative and compressed sensing based reconstruction methods on 3D digital tomosynthesis data sets and phantom models. A user friendly graphical user interface (GUI) helps users to select and run the desired methods on the designed phantom models or real data sets. The simulator has been tested on a phantom study that simulates breast tomosynthesis imaging problem. Results obtained with various methods including algebraic reconstruction technique (ART) and total variation regularized reconstruction techniques (ART+TV) are presented. Reconstruction results of the methods are compared both visually and quantitatively by evaluating performances of the methods using mean structural similarity (MSSIM) values.

3D Integration of MEMS and IC: Design, technology and simulations

OpenAIRE

Schjølberg-Henriksen, Kari

2009-01-01

* 3D integration: Opportunities and trends* e-CUBES: Tire pressure monitoring system (TPMS)* Package design including thermo-mechanical modeling* Technology development* Sensor packaging concept* Gold stud bump bonding* Device characterization and testing* Summary and outlook 3D Integration of MEMS and IC: Design, technology and simulations

Hierarchical Statistical 3D ' Atomistic' Simulation of Decanano MOSFETs: Drift-Diffusion, Hydrodynamic and Quantum Mechanical Approaches

Science.gov (United States)

Asenov, Asen; Brown, A. R.; Slavcheva, G.; Davies, J. H.

2000-01-01

When MOSFETs are scaled to deep submicron dimensions the discreteness and randomness of the dopant charges in the channel region introduces significant fluctuations in the device characteristics. This effect, predicted 20 year ago, has been confirmed experimentally and in simulation studies. The impact of the fluctuations on the functionality, yield, and reliability of the corresponding systems shifts the paradigm of the numerical device simulation. It becomes insufficient to simulate only one device representing one macroscopical design in a continuous charge approximation. An ensemble of macroscopically identical but microscopically different devices has to be characterized by simulation of statistically significant samples. The aims of the numerical simulations shift from predicting the characteristics of a single device with continuous doping towards estimating the mean values and the standard deviations of basic design parameters such as threshold voltage, subthreshold slope, transconductance, drive current, etc. for the whole ensemble of 'atomistically' different devices in the system. It has to be pointed out that even the mean values obtained from 'atomistic' simulations are not identical to the values obtained from continuous doping simulations. In this paper we present a hierarchical approach to the 'atomistic' simulation of aggressively scaled decanano MOSFETs. A full scale 3D drift-diffusion'atomostic' simulation approach is first described and used for verification of the more economical, but also more restricted, options. To reduce the processor time and memory requirements at high drain voltage we have developed a self-consistent option based on a thin slab solution of the current continuity equation only in the channel region. This is coupled to the Poisson's equation solution in the whole simulation domain in the Gummel iteration cycles. The accuracy of this approach is investigated in comparison with the full self-consistent solution. At low drain

Three-dimensional numerical simulation of the 20 June 1991, Orlando microburst

Science.gov (United States)

Proctor, Fred H.

1992-01-01

On 20 June 1991, NASA's Boeing 737, equipped with in-situ and look-ahead wind-shear detection systems, made direct low-level penetrations (300-350 m AGL) through a microburst during several stages of its evolution. This microburst was located roughly 20 km northeast of Orlando International Airport and was monitored by a Terminal Doppler Weather Radar (TDWR) located about 10 km south of the airport. The first NASA encounter with this microburst (Event 142), at approximately 2041 UTC, was during its intensification phase. At flight level, in-situ measurements indicated a peak 1-km (averaged) F-factor of approximately 0.1. The second NASA encounter (Event 143) occurred at approximately 2046 UTC, about the time of microburst peak intensity. It was during this penetration that a peak 1-km F-factor of approximately 17 was encountered, which was the largest in-situ measurement of the 1991 summer deployment. By the third encounter (Event 144), at approximately 2051 UTC, the microburst had expanded into a macroburst. During this phase of evolution, an in-situ 1-km F-factor of 0.08 was measured. The focus of this paper is to examine this microburst via numerical simulation from an unsteady, three-dimensional meteorological cloud model. The simulated high-resolution data fields of wind, temperature, radar reflectivity factor, and precipitation are closely examined so as to derive information not readily available from 'observations' and to enhance our understanding of the actual event. Characteristics of the simulated microburst evolution are compared with TDWR and in-situ measurements.

Enhancing Pre-Service Teachers' Awareness to Pupils' Test-Anxiety with 3D Immersive Simulation

Science.gov (United States)

Passig, David; Moshe, Ronit

2008-01-01

This study investigated whether participating in a 3D immersive virtual reality world simulating the experience of test-anxiety would affect preservice teachers' awareness to the phenomenon. Ninety subjects participated in this study, and were divided into three groups. The experimental group experienced a 3D immersive simulation which made…

Changes in the convective population and thermodynamic environments in convection-permitting regional climate simulations over the United States

Science.gov (United States)

Rasmussen, K. L.; Prein, A. F.; Rasmussen, R. M.; Ikeda, K.; Liu, C.

2017-11-01

Novel high-resolution convection-permitting regional climate simulations over the US employing the pseudo-global warming approach are used to investigate changes in the convective population and thermodynamic environments in a future climate. Two continuous 13-year simulations were conducted using (1) ERA-Interim reanalysis and (2) ERA-Interim reanalysis plus a climate perturbation for the RCP8.5 scenario. The simulations adequately reproduce the observed precipitation diurnal cycle, indicating that they capture organized and propagating convection that most climate models cannot adequately represent. This study shows that weak to moderate convection will decrease and strong convection will increase in frequency in a future climate. Analysis of the thermodynamic environments supporting convection shows that both convective available potential energy (CAPE) and convective inhibition (CIN) increase downstream of the Rockies in a future climate. Previous studies suggest that CAPE will increase in a warming climate, however a corresponding increase in CIN acts as a balancing force to shift the convective population by suppressing weak to moderate convection and provides an environment where CAPE can build to extreme levels that may result in more frequent severe convection. An idealized investigation of fundamental changes in the thermodynamic environment was conducted by shifting a standard atmospheric profile by ± 5 °C. When temperature is increased, both CAPE and CIN increase in magnitude, while the opposite is true for decreased temperatures. Thus, even in the absence of synoptic and mesoscale variations, a warmer climate will provide more CAPE and CIN that will shift the convective population, likely impacting water and energy budgets on Earth.

Calculation of residual stresses by means of a 3D numerical weld simulation

International Nuclear Information System (INIS)

Nicak, Tomas; Huemmer, Matthias

2008-01-01

The numerical weld simulation has developed very fast in recent years. The problem complexity has increased from simple 2D models to full 3D models, which can describe the entire welding process more realistically. As recent research projects indicate, a quantitative assessment of the residual stresses by means of a 3D analysis is possible. The structure integrity can be assessed based on the weld simulation results superimposed with the operating load. Moreover, to support the qualification of welded components parametric studies for optimization of the residual stress distribution in the weld region can be performed. In this paper a full 3D numerical weld simulation for a man-hole drainage nozzle in a steam generator will be presented. The residual stresses are calculated by means of an uncoupled transient thermal and mechanical FE analysis. The paper will present a robust procedure allowing reasonable predictions of the residual stresses for complex structures in industrial practice. (authors)

2D Numerical Simulation and Sensitive Analysis of H-Darrieus Wind Turbine

Directory of Open Access Journals (Sweden)

Seyed Mohammad E. Saryazdi

2018-02-01

Full Text Available Recently, a lot of attention has been devoted to the use of Darrieus wind turbines in urban areas. The aerodynamics of a Darrieus turbine are very complex due to dynamic stall and changing forces on the turbine triggered by changing horizontal angles. In this study, the aerodynamics of H-rotor vertical axis wind turbine (VAWT has been studied using computational fluid dynamics via two different turbulence models. Shear stress transport (SST k-ω turbulence model was used to simulate a 2D unsteady model of the H-Darrieus turbine. In order to complete this simulation, sensitivity analysis of the effective turbine parameters such as solidity factor, airfoil shape, wind velocity and shaft diameter were done. To simulate the flow through the turbine, a 2D simplified computational domain has been generated. Then fine mesh for each case consisting of different turbulence models and dimensions has been generated. Each mesh in this simulation dependent on effective parameters consisted of domain size, mesh quality, time step and total revolution. The sliding mesh method was applied to evaluate the unsteady interaction between the stationary and rotating components. Previous works just simulated turbine, while in our study sensitivity analysis of effective parameters was done. The simulation results closely match the experimental data, providing an efficient and reliable foundation to study wind turbine aerodynamics. This also demonstrates computing the best value of the effective parameter. The sensitivity analysis revealed best value of the effective parameter that could be used in the process of designing turbine. This work provides the first step in developing an accurate 3D aerodynamic modeling of Darrieus wind turbines. Article History: Received :August 19th 2017; Received: December 15th 2017; Accepted: Januari 14th 2018; Available online How to Cite This Article: Saryazdi, S. M. E. and Boroushaki, M. (2018 2D Numerical Simulation and Sensitive

A 4D digital phantom for patient-specific simulation of brain CT perfusion protocols.

Science.gov (United States)

van den Boom, Rieneke; Manniesing, Rashindra; Oei, Marcel T H; van der Woude, Willem-Jan; Smit, Ewoud J; Laue, Hendrik O A; van Ginneken, Bram; Prokop, Mathias

2014-07-01

Optimizing CT brain perfusion protocols is a challenge because of the complex interaction between image acquisition, calculation of perfusion data, and patient hemodynamics. Several digital phantoms have been developed to avoid unnecessary patient exposure or suboptimum choice of parameters. The authors expand this idea by using realistic noise patterns and measured tissue attenuation curves representing patient-specific hemodynamics. The purpose of this work is to validate that this approach can realistically simulate mean perfusion values and noise on perfusion data for individual patients. The proposed 4D digital phantom consists of three major components: (1) a definition of the spatial structure of various brain tissues within the phantom, (2) measured tissue attenuation curves, and (3) measured noise patterns. Tissue attenuation curves were measured in patient data using regions of interest in gray matter and white matter. By assigning the tissue attenuation curves to the corresponding tissue curves within the phantom, patient-specific CTP acquisitions were retrospectively simulated. Noise patterns were acquired by repeatedly scanning an anthropomorphic skull phantom at various exposure settings. The authors selected 20 consecutive patients that were scanned for suspected ischemic stroke and constructed patient-specific 4D digital phantoms using the individual patients' hemodynamics. The perfusion maps of the patient data were compared with the digital phantom data. Agreement between phantom- and patient-derived data was determined for mean perfusion values and for standard deviation in de perfusion data using intraclass correlation coefficients (ICCs) and a linear fit. ICCs ranged between 0.92 and 0.99 for mean perfusion values. ICCs for the standard deviation in perfusion maps were between 0.86 and 0.93. Linear fitting yielded slope values between 0.90 and 1.06. A patient-specific 4D digital phantom allows for realistic simulation of mean values and

Transient simulations in WWER-1000-comparison between DYN3D-ATHLET and DYN3D-RELAP5

International Nuclear Information System (INIS)

Grundmann, U.; Kliem, S.; Kozmenkov, Y.; Mittag, S.; Rohde, U.; Weiss, F.P.

2003-01-01

Simulations of a real transient of an operating WWER-1000 power plant have been performed using DYN3D-ATHLET (Gru95) and DYN3D-RELAP5 (Koy01) code systems in the frame of activities aimed at a validation of the neutronic / thermal-hydraulic coupled codes. The transient initiated by a main coolant pump switching off, when three of the four main coolant pumps of the plant are in operation (scenario of the VALCO project) is chosen for the simulation. The same models of the plant (except the core nodalization) but two different libraries of macroscopic cross-sections have been used in compared calculations. Additionally, the compared code systems are based on the different / external and internal / coupling techniques. This paper contains a brief description of the coupled codes and the plant model as well as a comparison between the results from simulations (Authors)

Bus.py: A GridLAB-D Communication Interface for Smart Distribution Grid Simulations

Energy Technology Data Exchange (ETDEWEB)

Hansen, Timothy M.; Palmintier, Bryan; Suryanarayanan, Siddharth; Maciejewski, Anthony A.; Siegel, Howard Jay

2015-07-03

As more Smart Grid technologies (e.g., distributed photovoltaic, spatially distributed electric vehicle charging) are integrated into distribution grids, static distribution simulations are no longer sufficient for performing modeling and analysis. GridLAB-D is an agent-based distribution system simulation environment that allows fine-grained end-user models, including geospatial and network topology detail. A problem exists in that, without outside intervention, once the GridLAB-D simulation begins execution, it will run to completion without allowing the real-time interaction of Smart Grid controls, such as home energy management systems and aggregator control. We address this lack of runtime interaction by designing a flexible communication interface, Bus.py (pronounced bus-dot-pie), that uses Python to pass messages between one or more GridLAB-D instances and a Smart Grid simulator. This work describes the design and implementation of Bus.py, discusses its usefulness in terms of some Smart Grid scenarios, and provides an example of an aggregator-based residential demand response system interacting with GridLAB-D through Bus.py. The small scale example demonstrates the validity of the interface and shows that an aggregator using said interface is able to control residential loads in GridLAB-D during runtime to cause a reduction in the peak load on the distribution system in (a) peak reduction and (b) time-of-use pricing cases.

Monte Carlo simulation of explosive detection system based on a Deuterium-Deuterium (D-D) neutron generator.

Science.gov (United States)

Bergaoui, K; Reguigui, N; Gary, C K; Brown, C; Cremer, J T; Vainionpaa, J H; Piestrup, M A

2014-12-01

An explosive detection system based on a Deuterium-Deuterium (D-D) neutron generator has been simulated using the Monte Carlo N-Particle Transport Code (MCNP5). Nuclear-based explosive detection methods can detect explosives by identifying their elemental components, especially nitrogen. Thermal neutron capture reactions have been used for detecting prompt gamma emission (10.82MeV) following radiative neutron capture by (14)N nuclei. The explosive detection system was built based on a fully high-voltage-shielded, axial D-D neutron generator with a radio frequency (RF) driven ion source and nominal yield of about 10(10) fast neutrons per second (E=2.5MeV). Polyethylene and paraffin were used as moderators with borated polyethylene and lead as neutron and gamma ray shielding, respectively. The shape and the thickness of the moderators and shields are optimized to produce the highest thermal neutron flux at the position of the explosive and the minimum total dose at the outer surfaces of the explosive detection system walls. In addition, simulation of the response functions of NaI, BGO, and LaBr3-based γ-ray detectors to different explosives is described. Copyright © 2014 Elsevier Ltd. All rights reserved.

Sismonaute. Un système pour la détection et l'interprétation des fronts d'onde en simulation sismique Sismonaute. A System for Detecting and Interpreting Wave Fronts in Seismic Simulations

Directory of Open Access Journals (Sweden)

Junker U.

2006-11-01

Full Text Available Nous développons un système, dénommé SISMONAUTE, d'aide aux géophysiciens pour l'étude de la propagation des ondes dans un modèle postulé de sous-sol. Le système suit les fronts d'onde dans une série d'instantanés 2D produits par un simulateur numérique. De plus, il rétablit l'historique de l'onde, c'est-à-dire la séquence des réflexions, transmissions et diffractions qui représente des transformations qualitatives de l'onde. Cet historique est essentiel pour la comparaison des sismogrammes simulés et observés. Nous utilisons pour interpréter les données de simulation un système dirigé par les connaissances qui applique le raisonnement causal pour prédire, à chaque stade, de nouveaux fronts d'onde. Ces fronts prédits permettent une détection guidée des fronts d'onde sur les instantanés. We are developing a system, called SISMONAUTE, that supports a geophysicist in studying the propagation of waves in a postulated model of the subsoil. The system tracks the wave fronts in a sequence of 2D-snapshots produced by a numerical simulator. Furthermore, it recovers the history of a wave, i. e. the sequence of reflections, transmissions, and diffractions which represents qualitative changes of the wave. This history is essential for comparing simulated and observed seismograms. We use a knowledge-driven approach to interpret the simulated data. Using causal reasoning, the system predicts new wave fronts in each step. These predicted fronts enable a guided detection of wave fronts in the snapshots.

Simulation de la désactivation d'un catalyseur d'hydrodémétallisation à géométrie ouverte Simulation of the Deactivation of a Hydrodemetallization Catalyst with an Open Geometry

Directory of Open Access Journals (Sweden)

Tanoubi I.

2006-11-01

Full Text Available On propose un outil de simulation prédictif de la désactivation au cours du temps d'un catalyseur d'hydrodémétallisation. Il repose sur un modèle de la géométrie du catalyseur, associé à une loi de diffusion des réactifs prenant en compte l'évolution texturale du catalyseur en cours de réaction. L'évolution de la texture est due au dépôt solide d'un des produits de la réaction dans les pores catalytiques. Le dépôt catalyse également la réaction mais de manière moins efficace que le catalyseur propre. La désactivation est liée à la diminution de la surface spécifique, et au bouchage progressif des pores. La géométrie prise en compte reflète la texture originale dite en bogue de châtaigne , qui caractérise les nouveaux catalyseurs d'hydrotraitement des résidus récemment développés à l'Institut Français du Pétrole (IFP. La simulation montre que cette géométrie particulière induit une meilleure stabilité du catalyseur vis à vis des facteurs de désactivation. Le modèle envisage d'abord une cinétique simple, tenant compte uniquement de la réaction de démétallisation. Par ailleurs, il est en mesure d'introduire une réaction compétitive pour justifier les observations expérimentales en milieu contaminé par des asphaltènes, à savoir l'occurrence des concentrations maximales en dépôt solide à l'intérieur des grains de catalyseurs, et non à leur périphérie immédiate. La simulation prédit l'évolution au cours du temps des profils le long du grain, de la surface spécifique, de la fraction de vide, de la concentration en réactif dans les pores, et de la masse de métaux déposés. Elle détermine également à chaque instant le flux du réactif à la surface du grain, ainsi que le facteur de Tamm et le taux de captation en métaux. Le modèle rend compte de manière satisfaisante des principales observations expérimentales, et constitue en outre un outil qualitatif très utile pour le d

Quantifying the added value of convection-permitting climate simulations in complex terrain: a systematic evaluation of WRF over the Himalayas

Science.gov (United States)

Karki, Ramchandra; Hasson, Shabeh ul; Gerlitz, Lars; Schickhoff, Udo; Scholten, Thomas; Böhner, Jürgen

2017-07-01

Mesoscale dynamical refinements of global climate models or atmospheric reanalysis have shown their potential to resolve intricate atmospheric processes, their land surface interactions, and subsequently, realistic distribution of climatic fields in complex terrains. Given that such potential is yet to be explored within the central Himalayan region of Nepal, we investigate the skill of the Weather Research and Forecasting (WRF) model with different spatial resolutions in reproducing the spatial, seasonal, and diurnal characteristics of the near-surface air temperature and precipitation as well as the spatial shifts in the diurnal monsoonal precipitation peak over the Khumbu (Everest), Rolwaling, and adjacent southern areas. Therefore, the ERA-Interim (0.75°) reanalysis has been dynamically refined to 25, 5, and 1 km (D1, D2, and D3) for one complete hydrological year (October 2014-September 2015), using the one-way nested WRF model run with mild nudging and parameterized convection for the outer but explicitly resolved convection for the inner domains. Our results suggest that D3 realistically reproduces the monsoonal precipitation, as compared to its underestimation by D1 but overestimation by D2. All three resolutions, however, overestimate precipitation from the westerly disturbances, owing to simulating anomalously higher intensity of few intermittent events. Temperatures are generally reproduced well by all resolutions; however, winter and pre-monsoon seasons feature a high cold bias for high elevations while lower elevations show a simultaneous warm bias. Unlike higher resolutions, D1 fails to realistically reproduce the regional-scale nocturnal monsoonal peak precipitation observed in the Himalayan foothills and its diurnal shift towards high elevations, whereas D2 resolves these characteristics but exhibits a limited skill in reproducing such a peak on the river valley scale due to the limited representation of the narrow valleys at 5 km resolution

Quantifying the added value of convection-permitting climate simulations in complex terrain: a systematic evaluation of WRF over the Himalayas

Directory of Open Access Journals (Sweden)

R. Karki

2017-07-01

Full Text Available Mesoscale dynamical refinements of global climate models or atmospheric reanalysis have shown their potential to resolve intricate atmospheric processes, their land surface interactions, and subsequently, realistic distribution of climatic fields in complex terrains. Given that such potential is yet to be explored within the central Himalayan region of Nepal, we investigate the skill of the Weather Research and Forecasting (WRF model with different spatial resolutions in reproducing the spatial, seasonal, and diurnal characteristics of the near-surface air temperature and precipitation as well as the spatial shifts in the diurnal monsoonal precipitation peak over the Khumbu (Everest, Rolwaling, and adjacent southern areas. Therefore, the ERA-Interim (0.75° reanalysis has been dynamically refined to 25, 5, and 1 km (D1, D2, and D3 for one complete hydrological year (October 2014–September 2015, using the one-way nested WRF model run with mild nudging and parameterized convection for the outer but explicitly resolved convection for the inner domains. Our results suggest that D3 realistically reproduces the monsoonal precipitation, as compared to its underestimation by D1 but overestimation by D2. All three resolutions, however, overestimate precipitation from the westerly disturbances, owing to simulating anomalously higher intensity of few intermittent events. Temperatures are generally reproduced well by all resolutions; however, winter and pre-monsoon seasons feature a high cold bias for high elevations while lower elevations show a simultaneous warm bias. Unlike higher resolutions, D1 fails to realistically reproduce the regional-scale nocturnal monsoonal peak precipitation observed in the Himalayan foothills and its diurnal shift towards high elevations, whereas D2 resolves these characteristics but exhibits a limited skill in reproducing such a peak on the river valley scale due to the limited representation of the narrow valleys at 5

File list: NoD.PSC.20.AllAg.hESC_derived_neural_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.hESC_derived_neural_cells hg19 No description Pluripotent stem cell hESC derived neural...edbc.jp/kyushu-u/hg19/assembled/NoD.PSC.20.AllAg.hESC_derived_neural_cells.bed ...

Sciences et éthique | conférence d'Axel Kahn | 20 novembre

CERN Multimedia

2012-01-01

Mardi 20 novembre 2012 à 20h30 Globe de la science et de l'innovation Route de Meyrin, 1211 Genève En français Tout public - entrée libre Nombre de places limité - réservation indispensable Réservation au +41 22 767 76 76 Parce que « le savoir est pouvoir pour l'homme de se rendre comme maître et possesseur de la nature », nous sommes collectivement de plus en plus savant et de plus en plus puissant. Reste à ce que notre sagesse nous conduise à utiliser nos pouvoirs au profit des personnes, et non à leur détriment, en d'autres termes, à ce que le progrès scientifique constitue une chance et non une menace. Pour qu'il en soit ainsi, il importe de non seulement développer les sciences et les techniques mais aussi de leur assigner des objectifs au centre desquels résident l'...

The Application of the Technology of 3D Satellite Cloud Imaging in Virtual Reality Simulation

Directory of Open Access Journals (Sweden)

Xiao-fang Xie

2007-05-01

Full Text Available Using satellite cloud images to simulate clouds is one of the new visual simulation technologies in Virtual Reality (VR. Taking the original data of satellite cloud images as the source, this paper depicts specifically the technology of 3D satellite cloud imaging through the transforming of coordinates and projection, creating a DEM (Digital Elevation Model of cloud imaging and 3D simulation. A Mercator projection was introduced to create a cloud image DEM, while solutions for geodetic problems were introduced to calculate distances, and the outer-trajectory science of rockets was introduced to obtain the elevation of clouds. For demonstration, we report on a computer program to simulate the 3D satellite cloud images.

Monte Carlo simulation of the response of a pixellated 3D photo-detector in silicon

CERN Document Server

Dubaric, E; Froejdh, C; Norlin, B

2002-01-01

The charge transport and X-ray photon absorption in three-dimensional (3D) X-ray pixel detectors have been studied using numerical simulations. The charge transport has been modelled using the drift-diffusion simulator MEDICI, while photon absorption has been studied using MCNP. The response of the entire pixel detector system in terms of charge sharing, line spread function and modulation transfer function, has been simulated using a system level Monte Carlo simulation approach. A major part of the study is devoted to the effect of charge sharing on the energy resolution in 3D-pixel detectors. The 3D configuration was found to suppress charge sharing much better than conventional planar detectors.

Conjunction of 2D and 3D modified flow solvers for simulating spatio-temporal wind induced hydrodynamics in the Caspian Sea

Science.gov (United States)

Zounemat-Kermani, Mohammad; Sabbagh-Yazdi, Saeed-Reza

2010-06-01

The main objective of this study is the simulation of flow dynamics in the deep parts of the Caspian Sea, in which the southern and middle deep regions are surrounded by considerable areas of shallow zones. To simulate spatio-temporal wind induced hydrodynamics in deep waters, a conjunctive numerical model consisting of a 2D depth average model and a 3D pseudo compressible model is proposed. The 2D model is applied to determine time dependent free surface oscillations as well as the surface velocity patterns and is conjunct to the 3D flow solver for computing three-dimensional velocity and pressure fields which coverage to steady state for the top boundary condition. The modified 2D and 3D sets of equations are conjunct considering interface shear stresses. Both sets of 2D and 3D equations are solved on unstructured triangular and tetrahedral meshes using the Galerkin Finite Volume Method. The conjunctive model is utilized to investigate the deep currents affected by wind, Coriolis forces and the river inflow conditions of the Caspian Sea. In this study, the simulation of flow field due to major winds as well as transient winds in the Caspian Sea during a period of 6 hours in the winter season has been conducted and the numerical results for water surface level are then compared to the 2D numerical results.

Three-dimensional simulation and auto-stereoscopic 3D display of the battlefield environment based on the particle system algorithm

Science.gov (United States)

Ning, Jiwei; Sang, Xinzhu; Xing, Shujun; Cui, Huilong; Yan, Binbin; Yu, Chongxiu; Dou, Wenhua; Xiao, Liquan

2016-10-01

The army's combat training is very important now, and the simulation of the real battlefield environment is of great significance. Two-dimensional information has been unable to meet the demand at present. With the development of virtual reality technology, three-dimensional (3D) simulation of the battlefield environment is possible. In the simulation of 3D battlefield environment, in addition to the terrain, combat personnel and the combat tool ,the simulation of explosions, fire, smoke and other effects is also very important, since these effects can enhance senses of realism and immersion of the 3D scene. However, these special effects are irregular objects, which make it difficult to simulate with the general geometry. Therefore, the simulation of irregular objects is always a hot and difficult research topic in computer graphics. Here, the particle system algorithm is used for simulating irregular objects. We design the simulation of the explosion, fire, smoke based on the particle system and applied it to the battlefield 3D scene. Besides, the battlefield 3D scene simulation with the glasses-free 3D display is carried out with an algorithm based on GPU 4K super-multiview 3D video real-time transformation method. At the same time, with the human-computer interaction function, we ultimately realized glasses-free 3D display of the simulated more realistic and immersed 3D battlefield environment.

Interactive virtual simulation using a 3D computer graphics model for microvascular decompression surgery.

Science.gov (United States)

Oishi, Makoto; Fukuda, Masafumi; Hiraishi, Tetsuya; Yajima, Naoki; Sato, Yosuke; Fujii, Yukihiko

2012-09-01

The purpose of this paper is to report on the authors' advanced presurgical interactive virtual simulation technique using a 3D computer graphics model for microvascular decompression (MVD) surgery. The authors performed interactive virtual simulation prior to surgery in 26 patients with trigeminal neuralgia or hemifacial spasm. The 3D computer graphics models for interactive virtual simulation were composed of the brainstem, cerebellum, cranial nerves, vessels, and skull individually created by the image analysis, including segmentation, surface rendering, and data fusion for data collected by 3-T MRI and 64-row multidetector CT systems. Interactive virtual simulation was performed by employing novel computer-aided design software with manipulation of a haptic device to imitate the surgical procedures of bone drilling and retraction of the cerebellum. The findings were compared with intraoperative findings. In all patients, interactive virtual simulation provided detailed and realistic surgical perspectives, of sufficient quality, representing the lateral suboccipital route. The causes of trigeminal neuralgia or hemifacial spasm determined by observing 3D computer graphics models were concordant with those identified intraoperatively in 25 (96%) of 26 patients, which was a significantly higher rate than the 73% concordance rate (concordance in 19 of 26 patients) obtained by review of 2D images only (p computer graphics model provided a realistic environment for performing virtual simulations prior to MVD surgery and enabled us to ascertain complex microsurgical anatomy.

Tomo3D 2.0--exploitation of advanced vector extensions (AVX) for 3D reconstruction.

Science.gov (United States)

Agulleiro, Jose-Ignacio; Fernandez, Jose-Jesus

2015-02-01

Tomo3D is a program for fast tomographic reconstruction on multicore computers. Its high speed stems from code optimization, vectorization with Streaming SIMD Extensions (SSE), multithreading and optimization of disk access. Recently, Advanced Vector eXtensions (AVX) have been introduced in the x86 processor architecture. Compared to SSE, AVX double the number of simultaneous operations, thus pointing to a potential twofold gain in speed. However, in practice, achieving this potential is extremely difficult. Here, we provide a technical description and an assessment of the optimizations included in Tomo3D to take advantage of AVX instructions. Tomo3D 2.0 allows huge reconstructions to be calculated in standard computers in a matter of minutes. Thus, it will be a valuable tool for electron tomography studies with increasing resolution needs. Copyright © 2014 Elsevier Inc. All rights reserved.

ARC+(Registered Trademark) and ARC PC Welding Simulators: Teach Welders with Virtual Interactive 3D Technologies

Science.gov (United States)

Choquet, Claude

2011-01-01

123 Certification Inc., a Montreal based company, has developed an innovative hands-on welding simulator solution to help build the welding workforce in the most simple way. The solution lies in virtual reality technology, which has been fully tested since the early 90's. President and founder of 123 Certification Inc., Mr. Claude Choquet Ing. Msc. IWE. acts as a bridge between the welding and the programming world. Working in these fields for more than 20 years. he has filed 12 patents world-wide for a gesture control platform with leading edge hardware related to simulation. In the summer of 2006. Mr Choquet was proud to be invited to the annual IIW International Weld ing Congress in Quebec City to launch the ARC+ welding simulator. A 100% virtual reality system and web based training center was developed to simulate multi process. multi-materiaL multi-position and multi pass welding. The simulator is intended to train welding students and apprentices in schools or industries. The welding simulator is composed of a real welding e[eetrode holder (SMAW-GTAW) and gun (GMAW-FCAW). a head mounted display (HMD), a 6 degrees of freedom tracking system for interaction between the user's hands and head. as well as external audio speakers. Both guns and HMD are interacting online and simultaneously. The welding simulation is based on the law of physics and empirical results from detailed analysis of a series of welding tests based on industrial applications tested over the last 20 years. The simulation runs in real-time, using a local logic network to determine the quality and shape of the created weld. These results are based on the orientation distance. and speed of the welding torch and depth of penetration. The welding process and resulting weld bc.1d are displayed in a virtual environment with screenplay interactive training modules. For review. weld quality and recorded process values can be displayed and diagnosed after welding. To help in the le.tming process, a

Nouvelle procédure pour l'augmentation du temps d'usinage simulé en coupe orthogonale

OpenAIRE

Guediche , Mayssa; Mabrouki , Tarek; Donnet , Christophe; Bergheau , Jean-Michel; Hamdi , Hedi

2015-01-01

International audience; Cette étude présente une nouvelle méthodologie visant à augmenter le temps d'usinage simulé en coupe orthogonale .Le but est d'étudier ultérieurement l'évolution de l'usure des outils de coupe dans le cas de l'usinage de l'acier 42CD4. Un modèle lagrangien est donc développé sous le code de calcul ABAQUS simulant la formation du copeau. Une approche baptisée de « modélisation verticale » est développée dans le but d'augmenter le temps de coupe simulé tout en gardant un...

File list: NoD.Utr.20.AllAg.Fallopian_tube_secretory_epithelial_cell [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.Utr.20.AllAg.Fallopian_tube_secretory_epithelial_cell hg19 No description Uterus Fallopian tube secret...ory epithelial cell http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.Utr.20.AllAg.Fallopian_tube_secretory_epithelial_cell.bed ...

File list: NoD.PSC.20.AllAg.hESC_derived_neural_crests [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.hESC_derived_neural_crests hg19 No description Pluripotent stem cell hESC derived neural... crests http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/NoD.PSC.20.AllAg.hESC_derived_neural_crests.bed ...

Simulation of Missing Pellet Surface thermal behavior with 3D dynamic gap element

International Nuclear Information System (INIS)

Kim, Hyo Chan; Yang, Yong Sik; Koo, Yang Hyun; Kang, Chang Hak; Lee Sung Uk; Yang, Dong Yol

2014-01-01

Most of the fuel performance codes that are able to simulate a multidimensional analysis are used to calculate the radial temperature distribution and perform a multidimensional mechanical analysis based on a one-dimensional (1D) temperature result. The FRAPCON-FRAPTRAN code system incorporates a 1D thermal module and two-dimensional (2D) mechanical module when FEM option is activated. In this method, the multidimensional gap conductance model is not required because one-dimensional thermal analysis is carried out. On the other hand, a gap conductance model for a multi-dimension should be developed in the code to perform a multidimensional thermal analysis. ALCYONE developed by CEA introduces an equivalent heat convection coefficient that represents the multidimensional gap conductance. However, the code does not employ dynamic gap conductance which is a function of gap thickness and gap characteristics in direct. The BISON code, which has been developed by INL (Idaho National Laboratory), employed a thermo-mechanical contact method that is specifically designed for tightly-coupled implicit solutions that employ Jacobian-free solution methods. Owing to tightly-coupled implicit solutions, the BISON code solves gap conductance and gap thickness simultaneously with given boundary conditions. In this paper, 3D dynamic gap element has been proposed to resolve convergence issue and nonlinear characteristic of multidimensional gap conductance. To evaluate 3D dynamic gap element module, 3D thermomechanical module using FORTRAN77 has been implemented incorporating 3D dynamic gap element. To demonstrate effect of 3D dynamic gap element, thermal behavior of missing pellet surface (MPS) has been simulated by the developed module. LWR fuel performance codes should incorporate thermo-mechanical loop to solve gap conductance problem, iteratively. However, gap conductance in multidimensional model is difficult issue owing to its nonlinearity and convergence characteristics. In

3D numerical simulation of transient processes in hydraulic turbines

International Nuclear Information System (INIS)

Cherny, S; Chirkov, D; Lapin, V; Eshkunova, I; Bannikov, D; Avdushenko, A; Skorospelov, V

2010-01-01

An approach for numerical simulation of 3D hydraulic turbine flows in transient operating regimes is presented. The method is based on a coupled solution of incompressible RANS equations, runner rotation equation, and water hammer equations. The issue of setting appropriate boundary conditions is considered in detail. As an illustration, the simulation results for runaway process are presented. The evolution of vortex structure and its effect on computed runaway traces are analyzed.

3D numerical simulation of transient processes in hydraulic turbines

Science.gov (United States)

Cherny, S.; Chirkov, D.; Bannikov, D.; Lapin, V.; Skorospelov, V.; Eshkunova, I.; Avdushenko, A.

2010-08-01

An approach for numerical simulation of 3D hydraulic turbine flows in transient operating regimes is presented. The method is based on a coupled solution of incompressible RANS equations, runner rotation equation, and water hammer equations. The issue of setting appropriate boundary conditions is considered in detail. As an illustration, the simulation results for runaway process are presented. The evolution of vortex structure and its effect on computed runaway traces are analyzed.

77 FR 22267 - Eagle Permits; Changes in the Regulations Governing Eagle Permitting

Science.gov (United States)

2012-04-13

... with rotating wind turbines. Permit Duration and Transferability In February 2011, we published draft... permit applicants, because of the known risk to eagles from collisions with wind turbines and electric... change does not affect the tenure of any other migratory bird or eagle permit type. DATES: Electronic...

Simulator sickness analysis of 3D video viewing on passive 3D TV

Science.gov (United States)

Brunnström, K.; Wang, K.; Andrén, B.

2013-03-01

The MPEG 3DV project is working on the next generation video encoding standard and in this process a call for proposal of encoding algorithms was issued. To evaluate these algorithm a large scale subjective test was performed involving Laboratories all over the world. For the participating Labs it was optional to administer a slightly modified Simulator Sickness Questionnaire (SSQ) from Kennedy et al (1993) before and after the test. Here we report the results from one Lab (Acreo) located in Sweden. The videos were shown on a 46 inch film pattern retarder 3D TV, where the viewers were using polarized passive eye-glasses to view the stereoscopic 3D video content. There were 68 viewers participating in this investigation in ages ranges from 16 to 72, with one third females. The questionnaire was filled in before and after the test, with a viewing time ranging between 30 min to about one and half hour, which is comparable to a feature length movie. The SSQ consists of 16 different symptoms that have been identified as important for indicating simulator sickness. When analyzing the individual symptoms it was found that Fatigue, Eye-strain, Difficulty Focusing and Difficulty Concentrating were significantly worse after than before. SSQ was also analyzed according to the model suggested by Kennedy et al (1993). All in all this investigation shows a statistically significant increase in symptoms after viewing 3D video especially related to visual or Oculomotor system.

Development of a 3D consistent 1D neutronics model for reactor core simulation

International Nuclear Information System (INIS)

Lee, Ki Bog; Joo, Han Gyu; Cho, Byung Oh; Zee, Sung Quun

2001-02-01

In this report a 3D consistent 1D model based on nonlinear analytic nodal method is developed to reproduce the 3D results. During the derivation, the current conservation factor (CCF) is introduced which guarantees the same axial neutron currents obtained from the 1D equation as the 3D reference values. Furthermore in order to properly use 1D group constants, a new 1D group constants representation scheme employing tables for the fuel temperature, moderator density and boron concentration is developed and functionalized for the control rod tip position. To test the 1D kinetics model with CCF, several steady state and transient calculations were performed and compared with 3D reference values. The errors of K-eff values were reduced about one tenth when using CCF without significant computational overhead. And the errors of power distribution were decreased to the range of one fifth or tenth at steady state calculation. The 1D kinetics model with CCF and the 1D group constant functionalization employing tables as a function of control rod tip position can provide preciser results at the steady state and transient calculation. Thus it is expected that the 1D kinetics model derived in this report can be used in the safety analysis, reactor real time simulation coupled with system analysis code, operator support system etc.

File list: NoD.PSC.20.AllAg.mESC_derived_pancreatic_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.mESC_derived_pancreatic_cells mm9 No description Pluripotent stem cell mESC derived panc...reatic cells http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.PSC.20.AllAg.mESC_derived_pancreatic_cells.bed ...

2.5D Simulation of basin-edge effects on the ground motion ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

The effects of basin-edge and soil velocity on the ground motion characteristics have been simulated ... Figure 1. 3-D and 2.5-D radial, transverse and vertical components of the radiation for .... sedimentary basin deserve a particular attention.

Semantic World Modelling and Data Management in a 4d Forest Simulation and Information System

Science.gov (United States)

Roßmann, J.; Hoppen, M.; Bücken, A.

2013-08-01

Various types of 3D simulation applications benefit from realistic forest models. They range from flight simulators for entertainment to harvester simulators for training and tree growth simulations for research and planning. Our 4D forest simulation and information system integrates the necessary methods for data extraction, modelling and management. Using modern methods of semantic world modelling, tree data can efficiently be extracted from remote sensing data. The derived forest models contain position, height, crown volume, type and diameter of each tree. This data is modelled using GML-based data models to assure compatibility and exchangeability. A flexible approach for database synchronization is used to manage the data and provide caching, persistence, a central communication hub for change distribution, and a versioning mechanism. Combining various simulation techniques and data versioning, the 4D forest simulation and information system can provide applications with "both directions" of the fourth dimension. Our paper outlines the current state, new developments, and integration of tree extraction, data modelling, and data management. It also shows several applications realized with the system.

Numerical simulation of 3D backward facing step flows at various Reynolds numbers

Directory of Open Access Journals (Sweden)

Louda Petr

2015-01-01

Full Text Available The work deals with the numerical simulation of 3D turbulent flow over backward facing step in a narrow channel. The mathematical model is based on the RANS equations with an explicit algebraic Reynolds stress model (EARSM. The numerical method uses implicit finite volume upwind discretization. While the eddy viscosity models fail in predicting complex 3D flows, the EARSM model is shown to provide results which agree well with experimental PIV data. The reference experimental data provide the 3D flow field. The simulations are compared with experiment for 3 values of Reynolds number.

specsim: A Fortran-77 program for conditional spectral simulation in 3D

Science.gov (United States)

Yao, Tingting

1998-12-01

A Fortran 77 program, specsim, is presented for conditional spectral simulation in 3D domains. The traditional Fourier integral method allows generating random fields with a given covariance spectrum. Conditioning to local data is achieved by an iterative identification of the conditional phase information. A flowchart of the program is given to illustrate the implementation procedures of the program. A 3D case study is presented to demonstrate application of the program. A comparison with the traditional sequential Gaussian simulation algorithm emphasizes the advantages and drawbacks of the proposed algorithm.

Tradeable carbon permits

International Nuclear Information System (INIS)

Koutstaal, P.R.

1995-01-01

The research project on tradeable carbon permits has focused on three elements. First of all, the practical implications of designing a system of tradeable emission permits for reducing CO2 has been studied. In the second part, the consequences of introducing a system of tradeable carbon permits for entry barriers have been considered. Finally, the institutional requirements and welfare effects of coordination of CO2 abatement in a second-best world have been examined

A decision aid tool for equity issues analysis in emission permit allocations

International Nuclear Information System (INIS)

Vaillancourt, K.; Waaub, J.P.

2004-01-01

The general intention of global climate agreements is to stabilize greenhouse gases (GHG) concentrations in the atmosphere which contribute to climate change. Climate models indicate that the global average temperature will increase by about 1.4 to 5.8 degrees C by 2100 compared to the 1990 level. This study assumed the participation of all countries, including developing countries, to achieve a global GHG stabilization target. It examined international cooperation mechanisms such as permit trading to achieve global economic efficiency. The study proposed a decision aid tool that provides relevant information on various equitable permit allocation schemes. A dynamic multicriterion model was presented to share the global quantity of permits among 15 regions. Multiple definitions of equity were considered. A realistic simulation of the World-MARKAL energy model was conducted to demonstrate the potential application of the scheme in international negotiations. The goal was to propose a range of permit allocations for each country in order to restrict the number of possibilities and guide negotiations. A model of the global reduction scenario makes it possible to determine cost effective solutions and to calculate reduction costs. Equity issues related to permit allocations were also addressed along with permit allocations and net reduction costs for each region. 45 refs., 5 tabs., 2 figs., 1 appendix

Simulation of 2D Granular Hopper Flow

Science.gov (United States)

Li, Zhusong; Shattuck, Mark

2012-02-01

Jamming and intermittent granular flow are big problems in industry, and the vertical hopper is a canonical example of these difficulties. We simulate gravity driven flow and jamming of 2D disks in a vertical hopper and compare with identical companion experiments presented in this session. We measure and compare the flow rate and probability for jamming as a function of particle properties and geometry. We evaluate the ability of standard Hertz-Mindlin contact mode to quantitatively predict the experimental flow.

Computer simulation of a 20-kHz power system for advanced launch systems

Science.gov (United States)

Sudhoff, S. D.; Wasynczuk, O.; Krause, P. C.; Kenny, B. H.

1993-01-01

The performance of two 20-kHz actuator power systems being built for an advanced launch system are evaluated for typical launch senario using an end-to-end system simulation. Aspects of system performance ranging from the switching of the power electronic devices to the vehicle aerodynamics are represented in the simulation. It is shown that both systems adequately stabilize the vehicle against a wind gust during launch. However, it is also shown that in both cases there are bus voltage and current fluctuations which make system power quality a concern.

77 FR 29450 - Actions on Special Permit Applications

Science.gov (United States)

2012-05-17

............ Conference of 49 CFR To modify the Radiation 172.203(d); special permit add Control Part 172, 49 CFR Part 172..., KY. the list of regulations exempted in paragraph 4. 11406-M......... Conference of 49 CFR Part To... mode of Berlin 173.345; transportation Packaging 173.346; (cargo vessel.) (Former 173.359; Grantee All...

Magneto-Hydrodynamic Simulations of a Magnetic Flux Compression Generator Using ALE3D

Science.gov (United States)

2017-07-01

3 Fig. 3 Half- plane view of the geometry used in ALE3D simulation showing the materials...to LLNL’s SESAME data.8 Fig. 3 Half- plane view of the geometry used in ALE3D simulation showing the materials There are 2 broad approaches to...of mesh can be time- consuming . Since MFCGs have a cylindrical geometry, a high-resolution mesh is not required; one can use a conformal mesh and

File list: NoD.PSC.20.AllAg.mESC_derived_neural_cells [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available NoD.PSC.20.AllAg.mESC_derived_neural_cells mm9 No description Pluripotent stem cell mESC derived neural... cells SRX440731,SRX440736 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/NoD.PSC.20.AllAg.mESC_derived_neural_cells.bed ...

State Licenses & Permits

Data.gov (United States)

Small Business Administration — Starting a business? Confused about whether you need a business license or permit? Virtually every business needs some form of license or permit to operate legally....

The CO{sub 2} emission permits market simulation using Continuous Double Auction

Energy Technology Data Exchange (ETDEWEB)

Bartoszczuk, Pawel [Warsaw School of Economics (Poland); Stanczak, Jaroslaw

2016-07-01

In this paper we consider the buying and selling prices of carbon dioxide (CO{sub 2}) emission permits in trading models with uncertainty. Permission prices, although usually omitted from standard models, may significantly influence the trading market. We thus construct a more realistic trade model. To do this, we introduced several important changes to the standard model, mainly we added The Continuous Double Action.

Application of a Detailed Emission Model for Heavy Duty Diesel Engine Simulations Application d'un modèle détaillé d'émissions pour la simulation de gros moteurs diesel

Directory of Open Access Journals (Sweden)

Magnusson I.

2006-12-01

Full Text Available A detailed chemical model describing the formation of soot and NO is applied to simulate emission formation in a heavy duty diesel engine. Cylinder flow and spray development is simulated using an engine CFD code - Speedstar. Combustion is described using a simple eddy break-up model. Modeling of the emission-chemistry/turbulent-flow interaction is based on a flamelet approach. Contrary to a typical flamelet concept, transport equations are solved for mass fractions of soot and NO. The reason being that these major emission constituencies are assumed to change slowly in comparison to typical time scales for chemical processes or transport processes important for combustion. Chemical reactions leading to production and destruction of soot and NO are, however, assumed to be fast. Soot and NO source terms are therefore evaluated from a flamelet library using a presumed probability density function and integrating over mixture fraction space. Results from simulations are compared to engine measurements inform of exhaust emission data and cylinder pressure. Un modèle avec chimie détaillée décrivant la formation des suies et du NO est appliqué à la simulation de la formation des polluants dans un gros moteur Diesel. L'écoulement et le spray sont modélisés avec le code de calcul Speedstar. La combustion est représentée par le modèle eddy break-up . La modélisation de l'interaction entre l'écoulement turbulent et la chimie des polluants est basée sur une approche de type flamelet . Cependant, à la différence d'autres travaux, des équations de transport pour les fractions massiques de suies et de NO sont résolues. Cela est justifié par la supposition que les temps caractéristiques de formation de ces composés sont longs comparés à ceux associés aux phénomènes de transport et aux réactions chimiques associées à la combustion. Cependant, les vitesses de réaction se rapportant aux suies et au NO sont supposées rapides. Cela

SU-D-9A-03: STAMP: Simulator for Texture Analysis in MRI/PET

Energy Technology Data Exchange (ETDEWEB)

Laberge, S; Vallieres, M; Levesque, I R.; El Naqa, I [McGill University, Montreal, QC (Canada)

2014-06-01

Purpose: To develop a convenient simulation platform to facilitate PET/MR image analysis with the prospect of gaining a better understanding of the influence of acquisition parameters on PET/MRI textural features. The simulation platform is demonstrated by showing textural variations of a representative case study using different image acquisition parameters. Methods: The simulation platform is composed of MRI simulators JEMRIS and SIMRI to achieve simulations of customized MRI sequences on sample tumor models. The PET simulator GATE is used to get 2D and 3D Monte Carlo acquisitions of voxelized PET sources using a phantom geometry and a customized scanner architecture. The platform incorporates a series of graphical user interfaces written in Matlab. Two GUIs are used to facilitate communication with the simulation executables installed on a computer cluster. A third GUI is used to collect and display the clinical and simulated images, as well as fused PET/MRI images, and perform computation of textural features.To illustrate the capabilities of this platform, one FDG-PET and T1-weighted (T1w) digitized tumor models were generated from clinical images of a soft-tissue sarcoma patient. Numerically simulated MR images were produced using 3 different echo times (TE) and 5 different repetition times (TR). PET 2D images were simulated using an OSEM algorithm with 1 to 32 iterations and a post-reconstruction Gaussian filter of 0, 2, 4 or 6 mm width. Results: STAMP was successfully used to produce numerically simulated FDG-PET and MRI images, and to calculate their corresponding textures. Three typical textures (GLCM-Contrast, GLSZM-ZSV and NGTDM-Coarseness) were found to vary by a range of 45% on average compared to reference scanning conditions in the case of FDG-PET, and by a range of 40% in the case of T1w MRI. Conclusion: We have successfully developed a Matlab-based simulation platform to facilitate PET/MRI texture image analysis for outcome prediction.

Water flow prediction for Membranes using 3D simulations with detailed morphology

KAUST Repository

Shi, Meixia

2015-04-01

The membrane morphology significantly influences membrane performance. For osmotically driven membrane processes, the morphology strongly affects the internal concentration polarization. Different membrane morphologies were generated by simulation and their influence on membrane performance was studied, using a 3D model. The simulation results were experimentally validated for two classical phase-inversion membrane morphologies: sponge- and finger-like structures. Membrane porosity and scanning electron microscopy image information were used as model input. The permeance results from the simulation fit well the experimentally measured permeances. Water permeances were predicted for different kinds of finger-like cavity membranes with different finger-like cavity lengths and various finger-like cavity sets, as well as for membranes with cylindrical cavities. The results provide realistic information on how to increase water permeance, and also illustrate that membrane’s complete morphology is important for the accurate water permeance evaluation. Evaluations only based on porosity might be misleading, and the new 3D simulation approach gives a more realistic representation.

Water flow prediction for Membranes using 3D simulations with detailed morphology

KAUST Repository

Shi, Meixia; Printsypar, Galina; Iliev, Oleg; Calo, Victor M.; Amy, Gary L.; Nunes, Suzana Pereira

2015-01-01

The membrane morphology significantly influences membrane performance. For osmotically driven membrane processes, the morphology strongly affects the internal concentration polarization. Different membrane morphologies were generated by simulation and their influence on membrane performance was studied, using a 3D model. The simulation results were experimentally validated for two classical phase-inversion membrane morphologies: sponge- and finger-like structures. Membrane porosity and scanning electron microscopy image information were used as model input. The permeance results from the simulation fit well the experimentally measured permeances. Water permeances were predicted for different kinds of finger-like cavity membranes with different finger-like cavity lengths and various finger-like cavity sets, as well as for membranes with cylindrical cavities. The results provide realistic information on how to increase water permeance, and also illustrate that membrane’s complete morphology is important for the accurate water permeance evaluation. Evaluations only based on porosity might be misleading, and the new 3D simulation approach gives a more realistic representation.

Development of 3D dynamic gap element for simulation of asymmetric fuel behavior

International Nuclear Information System (INIS)

Kim, Hyochan; Yang, Yongsik; Koo, Yanghyun; Kang, Changhak; Lee, Sunguk; Yang, Dongyol

2014-01-01

The accurate modeling of heat transfer across the gap between fuel pellets and the protective cladding is essential to understanding the fuel performance, including cladding stress and behavior under irradiated conditions. To establish a heat transfer model through a gap in the fuel performance code, the gap conductance based on the Ross and Stoute model was employed in most previous works. In this model, the gap conductance that determines the temperature gradient within the gap is a function of gap thickness, which is dependent on mechanical behavior. Recently, many researchers have been developing fuel performance codes based on the finite element method (FE) to calculate the temperature, stress, and strain in 2D or 3D. The gap conductance model for FE can be a challenging issue in terms of convergence and nonlinearity because the elements that are positioned in a gap have a different gap conductance, and the boundary conditions of the gap vary at each iteration step. In this paper, the specified 3D dynamic gap element has been proposed and implemented to simulate asymmetric thermo-mechanical fuel behavior. A thermo-mechanical 3D finite element module incorporating a gap element has been implemented using FORTRAN77. To evaluate the proposed 3D gap element, the missing pellet surface (MPS), which results in an asymmetric heat transfer in the pellet and cladding, was simulated. As a result, the maximum temperature of a pellet for the MPS problem calculated with the specified 3D gap element is much higher than the temperature calculated with a uniform gap conductance model that a multidimensional fuel performance code employs. The results demonstrate that a 3D simulation is essential to evaluate the temperature and stress of the pellet and cladding for an asymmetric geometry simulation. (author)

CABS-flex 2.0: a web server for fast simulations of flexibility of protein structures.

Science.gov (United States)

Kuriata, Aleksander; Gierut, Aleksandra Maria; Oleniecki, Tymoteusz; Ciemny, Maciej Pawel; Kolinski, Andrzej; Kurcinski, Mateusz; Kmiecik, Sebastian

2018-05-14

Classical simulations of protein flexibility remain computationally expensive, especially for large proteins. A few years ago, we developed a fast method for predicting protein structure fluctuations that uses a single protein model as the input. The method has been made available as the CABS-flex web server and applied in numerous studies of protein structure-function relationships. Here, we present a major update of the CABS-flex web server to version 2.0. The new features include: extension of the method to significantly larger and multimeric proteins, customizable distance restraints and simulation parameters, contact maps and a new, enhanced web server interface. CABS-flex 2.0 is freely available at http://biocomp.chem.uw.edu.pl/CABSflex2.

16 CFR Appendix D to Part 436 - Sample Item 20(3) Table-Status of Franchise Outlets

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Sample Item 20(3) Table-Status of Franchise Outlets D Appendix D to Part 436 Commercial Practices FEDERAL TRADE COMMISSION TRADE REGULATION RULES... Item 20(3) Table—Status of Franchise Outlets Status of Franchise Outlets For years 2004 to 2006 Column...

3D-finite element impact simulation on concrete structures

Energy Technology Data Exchange (ETDEWEB)

Heider, N.

1989-12-15

The analysis of impact processes is an interesting application of full 3D Finite Element calculations. This work presents a simulation of the penetration process of a Kinetic Energy projectile into a concrete target. Such a calculation requires an adequate FE model, especially a proper description of the crack opening process in front of the projectile. The aim is the prediction of the structural survival of the penetrator case with the help of an appropriate failure criterion. Also, the computer simulation allows a detailed analysis of the physical phenomena during impact. (orig.) With 4 refs., 14 figs.

Permit.LOA table

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This table includes the effective dates by vessel and permit number for each issued letter of authorization (LOA) by the Permit Office (APSD)

D-VASim: A Software Tool to Simulate and Analyze Genetic Logic Circuits

DEFF Research Database (Denmark)

Baig, Hasan; Madsen, Jan

2016-01-01

-stage researchers with limited experience in the field of biology. The Solution: Using LabVIEW to develop a user-friendly simulation tool named Dynamic Virtual Analyzer and Simulator (D-VASim), which is the first software tool in the domain of synthetic biology that provides a virtual laboratory environment...

Federal Fisheries Permit (FFP)/ Federal Processor Permit (FPP) Permit Program

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Federal Fisheries Permit (FFP) is required for vessels of the United States which are used to fish for groundfish in the Gulf of Alaska or Bering Sea and...

Precipitation Processes developed during ARM (1997), TOGA COARE (1992), GATE (1974), SCSMEX (1998), and KWAJEX (1999), Consistent 2D, semi-3D and 3D Cloud Resolving Model Simulations

Science.gov (United States)

Tao, Wei-Kuo; Hou, A.; Atlas, R.; Starr, D.; Sud, Y.

2003-01-01

Real clouds and cloud systems are inherently three-dimensional (3D). Because of the limitations in computer resources, however, most cloud-resolving models (CRMs) today are still two-dimensional (2D). A few 3D CRMs have been used to study the response of clouds to large-scale forcing. In these 3D simulations, the model domain was small, and the integration time was 6 hours. The major objectives of this paper are: (1) to assess the performance of the super-parameterization technique (i.e. is 2D or semi-3D CRM appropriate for the super-parameterization?); (2) calculate and examine the surface energy (especially radiation) and water budgets; (3) identify the differences and similarities in the organization and entrainment rates of convection between simulated 2D and 3D cloud systems.

3D thermal modeling of TRISO fuel coupled with neutronic simulation

Energy Technology Data Exchange (ETDEWEB)

Hu, Jianwei [Los Alamos National Laboratory; Uddin, Rizwan [UNIV OF ILLINIOS

2010-01-01

The Very High Temperature Gas Reactor (VHTR) is widely considered as one of the top candidates identified in the Next Generation Nuclear Power-plant (NGNP) Technology Roadmap under the U.S . Depanment of Energy's Generation IV program. TRlSO particle is a common element among different VHTR designs and its performance is critical to the safety and reliability of the whole reactor. A TRISO particle experiences complex thermo-mechanical changes during reactor operation in high temperature and high burnup conditions. TRISO fuel performance analysis requires evaluation of these changes on micro scale. Since most of these changes are temperature dependent, 3D thermal modeling of TRISO fuel is a crucial step of the whole analysis package. In this paper, a 3D numerical thermal model was developed to calculate temperature distribution inside TRISO and pebble under different scenarios. 3D simulation is required because pebbles or TRISOs are always subjected to asymmetric thermal conditions since they are randomly packed together. The numerical model was developed using finite difference method and it was benchmarked against ID analytical results and also results reported from literature. Monte-Carlo models were set up to calculate radial power density profile. Complex convective boundary condition was applied on the pebble outer surface. Three reactors were simulated using this model to calculate temperature distribution under different power levels. Two asymmetric boundary conditions were applied to the pebble to test the 3D capabilities. A gas bubble was hypothesized inside the TRISO kernel and 3D simulation was also carried out under this scenario. Intuition-coherent results were obtained and reported in this paper.

Simulating streamer discharges in 3D with the parallel adaptive Afivo framework

NARCIS (Netherlands)

H.J. Teunissen (Jannis); U. M. Ebert (Ute)

2017-01-01

htmlabstractWe present an open-source plasma fluid code for 2D, cylindrical and 3D simulations of streamer discharges, based on the Afivo framework that features adaptive mesh refinement, geometric multigrid methods for Poisson's equation, and OpenMP parallelism. We describe the numerical

Production and use of Li(d,n) neutrons for simulation of radiation effects in fusion reactors

International Nuclear Information System (INIS)

Goland, A.N.; Gurinsky, D.H.; Hendrie, J.; Kukkonen, J.; Sheehan, T.; Snead, C.L. Jr.

1975-01-01

In the Brookhaven Accelerator-Based Neutron Generator 1.5-cm thick x 12-cm wide films of lithium flowing at the velocity of approximately 10 m sec -1 will be the targets for 30-MeV D + and D - beams 1-cm high and 10-cm wide. At this energy a beam of energetic neutrons is emitted mainly in the forward direction (theta less than or equal to 20 0 ) as a result of the Li(d,n) breakup reaction. Measurements of the neutron flux and spectrum as a function of incident deuteron energy and emission angle theta(theta less than or equal to 20 0 ) indicate that the yield increases approximately linearly with increasing deuteron energy from 25 MeV to at least 35 MeV, and that the mean energy of the neutrons (theta = 0 0 ) is about 0.4 of the incident deuteron energies between 25 and 35 MeV. The most probable neutron energy in the forward-directed (theta = 0 0 ) spectrum is also about 0.4 of the deuteron energy over this range. For a 30-MeV beam, the full width at half maximum of the neutron spectrum is 11.8 MeV (theta = 0 0 ), and the mean neutron energy is 13 MeV. Pertinent radiation-damage parameters were calculated for various materials exposed to this neutron spectrum. In Nb, for example, the helium production rate and the displacement rate simulate the values anticipated in a D-T fusion reactor spectrum of comparable flux. Furthermore, the primary-recoil-atom energy distributions produced by Li(d,n) neutrons in Al, Nb, and Au are similar to those produced by 14-MeV neutrons. (U.S.)

From 4D Medical Images (CT, MRI, and Ultrasound to 4D Structured Mesh Models of the Left Ventricular Endocardium for Patient-Specific Simulations

Directory of Open Access Journals (Sweden)

Federico Canè

2018-01-01

Full Text Available With cardiovascular disease (CVD remaining the primary cause of death worldwide, early detection of CVDs becomes essential. The intracardiac flow is an important component of ventricular function, motion kinetics, wash-out of ventricular chambers, and ventricular energetics. Coupling between Computational Fluid Dynamics (CFD simulations and medical images can play a fundamental role in terms of patient-specific diagnostic tools. From a technical perspective, CFD simulations with moving boundaries could easily lead to negative volumes errors and the sudden failure of the simulation. The generation of high-quality 4D meshes (3D in space + time with 1-to-1 vertex becomes essential to perform a CFD simulation with moving boundaries. In this context, we developed a semiautomatic morphing tool able to create 4D high-quality structured meshes starting from a segmented 4D dataset. To prove the versatility and efficiency, the method was tested on three different 4D datasets (Ultrasound, MRI, and CT by evaluating the quality and accuracy of the resulting 4D meshes. Furthermore, an estimation of some physiological quantities is accomplished for the 4D CT reconstruction. Future research will aim at extending the region of interest, further automation of the meshing algorithm, and generating structured hexahedral mesh models both for the blood and myocardial volume.

[Accuracy of morphological simulation for orthognatic surgery. Assessment of a 3D image fusion software.

Science.gov (United States)

Terzic, A; Schouman, T; Scolozzi, P

2013-08-06

The CT/CBCT data allows for 3D reconstruction of skeletal and untextured soft tissue volume. 3D stereophotogrammetry technology has strongly improved the quality of facial soft tissue surface texture. The combination of these two technologies allows for an accurate and complete reconstruction. The 3D virtual head may be used for orthognatic surgical planning, virtual surgery, and morphological simulation obtained with a software dedicated to the fusion of 3D photogrammetric and radiological images. The imaging material include: a multi-slice CT scan or broad field CBCT scan, a 3D photogrammetric camera. The operative image processing protocol includes the following steps: 1) pre- and postoperative CT/CBCT scan and 3D photogrammetric image acquisition; 2) 3D image segmentation and fusion of untextured CT/CBCT skin with the preoperative textured facial soft tissue surface of the 3D photogrammetric scan; 3) image fusion of the pre- and postoperative CT/CBCT data set virtual osteotomies, and 3D photogrammetric soft tissue virtual simulation; 4) fusion of virtual simulated 3D photogrammetric and real postoperative images, and assessment of accuracy using a color-coded scale to measure the differences between the two surfaces. Copyright © 2013. Published by Elsevier Masson SAS.

OpenQ∗D simulation code for QCD+QED

DEFF Research Database (Denmark)

Campos, Isabel; Fritzsch, Patrick; Hansen, Martin

2018-01-01

The openQ∗D code for the simulation of QCD+QED with C∗ boundary conditions is presented. This code is based on openQCD-1.6, from which it inherits the core features that ensure its efficiency: the locally-deflated SAP-preconditioned GCR solver, the twisted-mass frequency splitting of the fermion....... An alpha version of this code is publicly available and can be downloaded from http://rcstar.web.cern.ch/....

Gear Mesh Loss-of-Lubrication Experiments and Analytical Simulation

Science.gov (United States)

Handschuh, Robert F.; Polly, Joseph; Morales, Wilfredo

2011-01-01

An experimental program to determine the loss-of-lubrication (LOL) characteristics of spur gears in an aerospace simulation test facility has been completed. Tests were conducted using two different emergency lubricant types: (1) an oil mist system (two different misted lubricants) and (2) a grease injection system (two different grease types). Tests were conducted using a NASA Glenn test facility normally used for conducting contact fatigue. Tests were run at rotational speeds up to 10000 rpm using two different gear designs and two different gear materials. For the tests conducted using an air-oil misting system, a minimum lubricant injection rate was determined to permit the gear mesh to operate without failure for at least 1 hr. The tests allowed an elevated steady state temperature to be established. A basic 2-D heat transfer simulation has been developed to investigate temperatures of a simulated gear as a function of frictional behavior. The friction (heat generation source) between the meshing surfaces is related to the position in the meshing cycle, the load applied, and the amount of lubricant in the contact. Experimental conditions will be compared to those from the 2-D simulation.

Renal Tumor Cryoablation Planning. The Efficiency of Simulation on Reconstructed 3D CT Scan

Directory of Open Access Journals (Sweden)

Ciprian Valerian LUCAN

2010-12-01

Full Text Available Introduction & Objective: Nephron-sparing surgical techniques risks are related to tumor relationships with adjacent anatomic structures. Complexity of the renal anatomy drives the interest to develop tools for 3D reconstruction and surgery simulation. The aim of the article was to assess the simulation on reconstructed 3D CT scan used for planning the cryoablation. Material & Method: A prospective randomized study was performed between Jan. 2007 and July 2009 on 27 patients who underwent retroperitoneoscopic T1a renal tumors cryoablation (RC. All patients were assessed preoperatively by CT scan, also used for 3D volume rendering. In the Gr.A, the patients underwent surgery planning by simulation on 3D CT scan. In the Gr.B., patients underwent standard RC. The two groups were compared in terms of surgical time, bleeding, postoperative drainage, analgesics requirement, hospital stay, time to socio-professional reintegration. Results: Fourteen patients underwent preoperative cryoablation planning (Gr.A and 13 patients underwent standard CR (Gr.B. All parameters analyzed were shorter in the Gr.A. On multivariate logistic regression, only shortens of the surgical time (138.79±5.51 min. in Gr.A. vs. 140.92±5.54 min in Gr.B. and bleeding (164.29±60.22 mL in Gr.A. vs. 215.38±100.80 mL in Gr.B. achieved statistical significance (p<0.05. The number of cryoneedles assessed by simulation had a 92.52% accuracy when compared with those effectively used. Conclusions: Simulation of the cryoablation using reconstructed 3D CT scan improves the surgical results. The application used for simulation was able to accurately assess the number of cryoneedles required for tumor ablation, their direction and approach.

Titan2D simulations of dome-collapse pyroclastic flows for crisis assessments on Montserrat

Science.gov (United States)

Widiwijayanti, C.; Voight, B.; Hidayat, D.; Patra, A.; Pitman, E.

2010-12-01

The Soufriere Hills Volcano (SHV), Montserrat, has experienced numerous episodes of lava dome collapses since 1995. Collapse volumes range from small rockfalls to major dome collapses (as much as ~200 M m3). Problems arise in hazards mitigation, particularly in zoning for populated areas. Determining the likely extent of flowage deposits in various scenarios is important for hazards zonation, provision of advice by scientists, and decision making by public officials. Towards resolution of this issue we have tested the TITAN2D code, calibrated parameters for an SHV database, and using updated topography have provided flowage maps for various scenarios and volume classes from SHV, for use in hazards assessments. TITAN2D is a map plane (depth averaged) simulator of granular flow and yields mass distributions over a DEM. Two Coulomb frictional parameters (basal and internal frictions) and initial source conditions (volume, source location, and source geometry) of single or multiple pulses in a dome-collapse type event control behavior of the flow. Flow kinematics are captured, so that the dynamics of flow can be examined spatially from frame to frame, or as a movie. Our hazard maps include not only the final deposit, but also areas inundated by moving debris prior to deposition. Simulations from TITAN2D were important for analysis of crises in the period 2007-2010. They showed that any very large mass released on the north slope would be strongly partitioned by local topography, and thus it was doubtful that flows of very large size (>20 M m3) could be generated in the Belham River drainage. This partitioning effect limited runout toward populated areas. These effects were interpreted to greatly reduce the down-valley risk of ash-cloud surges.

Pre-operative simulation of pediatric mastoid surgery with 3D-printed temporal bone models.

Science.gov (United States)

Rose, Austin S; Webster, Caroline E; Harrysson, Ola L A; Formeister, Eric J; Rawal, Rounak B; Iseli, Claire E

2015-05-01

As the process of additive manufacturing, or three-dimensional (3D) printing, has become more practical and affordable, a number of applications for the technology in the field of pediatric otolaryngology have been considered. One area of promise is temporal bone surgical simulation. Having previously developed a model for temporal bone surgical training using 3D printing, we sought to produce a patient-specific model for pre-operative simulation in pediatric otologic surgery. Our hypothesis was that the creation and pre-operative dissection of such a model was possible, and would demonstrate potential benefits in cases of abnormal temporal bone anatomy. In the case presented, an 11-year-old boy underwent a planned canal-wall-down (CWD) tympano-mastoidectomy for recurrent cholesteatoma preceded by a pre-operative surgical simulation using 3D-printed models of the temporal bone. The models were based on the child's pre-operative clinical CT scan and printed using multiple materials to simulate both bone and soft tissue structures. To help confirm the models as accurate representations of the child's anatomy, distances between various anatomic landmarks were measured and compared to the temporal bone CT scan and the 3D model. The simulation allowed the surgical team to appreciate the child's unusual temporal bone anatomy as well as any challenges that might arise in the safety of the temporal bone laboratory, prior to actual surgery in the operating room (OR). There was minimal variability, in terms of absolute distance (mm) and relative distance (%), in measurements between anatomic landmarks obtained from the patient intra-operatively, the pre-operative CT scan and the 3D-printed models. Accurate 3D temporal bone models can be rapidly produced based on clinical CT scans for pre-operative simulation of specific challenging otologic cases in children, potentially reducing medical errors and improving patient safety. Copyright © 2015 Elsevier Ireland Ltd. All rights

3-D FDTD simulation of shear waves for evaluation of complex modulus imaging.

Science.gov (United States)

Orescanin, Marko; Wang, Yue; Insana, Michael

2011-02-01

The Navier equation describing shear wave propagation in 3-D viscoelastic media is solved numerically with a finite differences time domain (FDTD) method. Solutions are formed in terms of transverse scatterer velocity waves and then verified via comparison to measured wave fields in heterogeneous hydrogel phantoms. The numerical algorithm is used as a tool to study the effects on complex shear modulus estimation from wave propagation in heterogeneous viscoelastic media. We used an algebraic Helmholtz inversion (AHI) technique to solve for the complex shear modulus from simulated and experimental velocity data acquired in 2-D and 3-D. Although 3-D velocity estimates are required in general, there are object geometries for which 2-D inversions provide accurate estimations of the material properties. Through simulations and experiments, we explored artifacts generated in elastic and dynamic-viscous shear modulus images related to the shear wavelength and average viscosity.

Simulação 3D de movimento ortodôntico 3D simulation of orthodontic tooth movement

Directory of Open Access Journals (Sweden)

Norman Duque Penedo

2010-10-01

Full Text Available OBJETIVO: desenvolver e validar, através do Método dos Elementos Finitos (MEF, um modelo numérico tridimensional (3D de um incisivo central superior para simular o movimento dentário. MÉTODOS: esse modelo contempla a unidade dentária, o osso alveolar e o ligamento periodontal. Permite a simulação dos diferentes movimentos dentários e a determinação dos centros de rotação e de resistência. Limita o movimento ao espaço periodontal, registrando a direção, quantificando o deslocamento dentário e as tensões iniciais no ligamento periodontal. RESULTADOS: a análise dos deslocamentos dentários e das áreas que recebem tensões iniciais possibilita determinar os tipos de movimentos dentários. Com base nas forças ortodônticas, é possível quantificar a intensidade das tensões em cada região do dente, do ligamento periodontal ou do osso alveolar. Com base nas tensões axiais ao longo do ligamento periodontal e da tensão capilar, é possível predizer, teoricamente, as regiões em que deve ocorrer a remodelação óssea. CONCLUSÃO: o modelo foi validado pela determinação do módulo de elasticidade do ligamento periodontal de forma compatível com dados experimentais existentes na literatura. Os métodos utilizados na construção do modelo permitiram a criação de um modelo completo para uma arcada dentária, o qual possibilita realizar variadas simulações que envolvem a mecânica ortodôntica.OBJECTIVE: To develop and validate a three-dimensional (3D numerical model of a maxillary central incisor to simulate tooth movement using the Finite Element Method (FEM. METHODS: This model encompasses the tooth, alveolar bone and periodontal ligament. It allows the simulation of different tooth movements and the establishment of centers of rotation and resistance. It limits the movement into the periodontal space, recording the direction, quantifying tooth displacement and initial stress in the periodontal ligament. RESULTS: By

A computational model to generate simulated three-dimensional breast masses

Energy Technology Data Exchange (ETDEWEB)

Sisternes, Luis de; Brankov, Jovan G.; Zysk, Adam M.; Wernick, Miles N., E-mail: wernick@iit.edu [Medical Imaging Research Center, Department of Electrical and Computer Engineering, Illinois Institute of Technology, Chicago, Illinois 60616 (United States); Schmidt, Robert A. [Kurt Rossmann Laboratories for Radiologic Image Research, Department of Radiology, The University of Chicago, Chicago, Illinois 60637 (United States); Nishikawa, Robert M. [Department of Radiology, University of Pittsburgh, Pittsburgh, Pennsylvania 15213 (United States)

2015-02-15

Purpose: To develop algorithms for creating realistic three-dimensional (3D) simulated breast masses and embedding them within actual clinical mammograms. The proposed techniques yield high-resolution simulated breast masses having randomized shapes, with user-defined mass type, size, location, and shape characteristics. Methods: The authors describe a method of producing 3D digital simulations of breast masses and a technique for embedding these simulated masses within actual digitized mammograms. Simulated 3D breast masses were generated by using a modified stochastic Gaussian random sphere model to generate a central tumor mass, and an iterative fractal branching algorithm to add complex spicule structures. The simulated masses were embedded within actual digitized mammograms. The authors evaluated the realism of the resulting hybrid phantoms by generating corresponding left- and right-breast image pairs, consisting of one breast image containing a real mass, and the opposite breast image of the same patient containing a similar simulated mass. The authors then used computer-aided diagnosis (CAD) methods and expert radiologist readers to determine whether significant differences can be observed between the real and hybrid images. Results: The authors found no statistically significant difference between the CAD features obtained from the real and simulated images of masses with either spiculated or nonspiculated margins. Likewise, the authors found that expert human readers performed very poorly in discriminating their hybrid images from real mammograms. Conclusions: The authors’ proposed method permits the realistic simulation of 3D breast masses having user-defined characteristics, enabling the creation of a large set of hybrid breast images containing a well-characterized mass, embedded within real breast background. The computational nature of the model makes it suitable for detectability studies, evaluation of computer aided diagnosis algorithms, and

A computational model to generate simulated three-dimensional breast masses

International Nuclear Information System (INIS)

Sisternes, Luis de; Brankov, Jovan G.; Zysk, Adam M.; Wernick, Miles N.; Schmidt, Robert A.; Nishikawa, Robert M.

2015-01-01

Purpose: To develop algorithms for creating realistic three-dimensional (3D) simulated breast masses and embedding them within actual clinical mammograms. The proposed techniques yield high-resolution simulated breast masses having randomized shapes, with user-defined mass type, size, location, and shape characteristics. Methods: The authors describe a method of producing 3D digital simulations of breast masses and a technique for embedding these simulated masses within actual digitized mammograms. Simulated 3D breast masses were generated by using a modified stochastic Gaussian random sphere model to generate a central tumor mass, and an iterative fractal branching algorithm to add complex spicule structures. The simulated masses were embedded within actual digitized mammograms. The authors evaluated the realism of the resulting hybrid phantoms by generating corresponding left- and right-breast image pairs, consisting of one breast image containing a real mass, and the opposite breast image of the same patient containing a similar simulated mass. The authors then used computer-aided diagnosis (CAD) methods and expert radiologist readers to determine whether significant differences can be observed between the real and hybrid images. Results: The authors found no statistically significant difference between the CAD features obtained from the real and simulated images of masses with either spiculated or nonspiculated margins. Likewise, the authors found that expert human readers performed very poorly in discriminating their hybrid images from real mammograms. Conclusions: The authors’ proposed method permits the realistic simulation of 3D breast masses having user-defined characteristics, enabling the creation of a large set of hybrid breast images containing a well-characterized mass, embedded within real breast background. The computational nature of the model makes it suitable for detectability studies, evaluation of computer aided diagnosis algorithms, and

Analysis of neutronic parameters of AP1000 core for 18 month and 16/20 month cycle schemes using CASMO4E and SIMULATE-3 codes

International Nuclear Information System (INIS)

Nawaz Amjad; Yoshikawa, Hidekazu; Ming Yang

2015-01-01

AP1000 reactor is designed for 18 month of operating cycle. The core can also be used for 16/20 months of operating cycle. This study is performed to analyze and compare the neutronic parameters of typical AP1000 reactor core for 18 month and 16/20 month alternate cycle lengths. CASMO4E and SIMULATE-3 code package is used for the analysis of initial and equilibrium cores. The key reactor physics safety parameters were analyzed including power peaking factors, core radial and axial power distribution and core reactivity feedback coefficients. Moreover, the analysis of fuel depletion, fission product buildup and burnable poison behaviour with burnup is also analyzed. Full 2-D fuel assembly model in CASMO4E and full 3-D core model in SIMULATE-3 is employed to examine core performance and safety parameters. In order to evaluate the equilibrium core neutronic parameters, the equilibrium core model is attained by performing burnup analysis from initial to equilibrium cycle, where optimized transition core design is obtained so that the power peaking factors remain within designed limits. The MTC for higher concentration of critical boron concentrations is slightly positive at lower moderator temperatures. However, it remains negative at operating temperature ranges. The radial core relative power distribution indicates that low leakage capability of initial and equilibrium cores is reduced at EOC. (author)

Simulations of Aperture Synthesis Imaging Radar for the EISCAT_3D Project

Science.gov (United States)

La Hoz, C.; Belyey, V.

2012-12-01

EISCAT_3D is a project to build the next generation of incoherent scatter radars endowed with multiple 3-dimensional capabilities that will replace the current EISCAT radars in Northern Scandinavia. Aperture Synthesis Imaging Radar (ASIR) is one of the technologies adopted by the EISCAT_3D project to endow it with imaging capabilities in 3-dimensions that includes sub-beam resolution. Complemented by pulse compression, it will provide 3-dimensional images of certain types of incoherent scatter radar targets resolved to about 100 metres at 100 km range, depending on the signal-to-noise ratio. This ability will open new research opportunities to map small structures associated with non-homogeneous, unstable processes such as aurora, summer and winter polar radar echoes (PMSE and PMWE), Natural Enhanced Ion Acoustic Lines (NEIALs), structures excited by HF ionospheric heating, meteors, space debris, and others. To demonstrate the feasibility of the antenna configurations and the imaging inversion algorithms a simulation of synthetic incoherent scattering data has been performed. The simulation algorithm incorporates the ability to control the background plasma parameters with non-homogeneous, non-stationary components over an extended 3-dimensional space. Control over the positions of a number of separated receiving antennas, their signal-to-noise-ratios and arriving phases allows realistic simulation of a multi-baseline interferometric imaging radar system. The resulting simulated data is fed into various inversion algorithms. This simulation package is a powerful tool to evaluate various antenna configurations and inversion algorithms. Results applied to realistic design alternatives of EISCAT_3D will be described.

Simulating condensation on microstructured surfaces using Lattice Boltzmann Method

Science.gov (United States)

Alexeev, Alexander; Vasyliv, Yaroslav

2017-11-01

We simulate a single component fluid condensing on 2D structured surfaces with different wettability. To simulate the two phase fluid, we use the athermal Lattice Boltzmann Method (LBM) driven by a pseudopotential force. The pseudopotential force results in a non-ideal equation of state (EOS) which permits liquid-vapor phase change. To account for thermal effects, the athermal LBM is coupled to a finite volume discretization of the temperature evolution equation obtained using a thermal energy rate balance for the specific internal energy. We use the developed model to probe the effect of surface structure and surface wettability on the condensation rate in order to identify microstructure topographies promoting condensation. Financial support is acknowledged from Kimberly-Clark.

Neutron spectrum determination of d(20)+Be source reaction by the dosimetry foils method

Science.gov (United States)

Stefanik, Milan; Bem, Pavel; Majerle, Mitja; Novak, Jan; Simeckova, Eva

2017-11-01

The cyclotron-based fast neutron generator with the thick beryllium target operated at the NPI Rez Fast Neutron Facility is primarily designed for the fast neutron production in the p+Be source reaction at 35 MeV. Besides the proton beam, the isochronous cyclotron U-120M at the NPI provides the deuterons in the energy range of 10-20 MeV. The experiments for neutron field investigation from the deuteron bombardment of thick beryllium target at 20 MeV were performed just recently. For the neutron spectrum measurement of the d(20)+Be source reaction, the dosimetry foils activation method was utilized. Neutron spectrum reconstruction from resulting reaction rates was performed using the SAND-II unfolding code and neutron cross-sections from the EAF-2010 nuclear data library. Obtained high-flux white neutron field from the d(20)+Be source is useful for the intensive irradiation experiments and cross-section data validation.

NECTAR: Simulation and Visualization in a 3D Collaborative Environment

NARCIS (Netherlands)

Law, Y.W.; Chan, K.Y.

For simulation and visualization in a 3D collaborative environment, an architecture called the Nanyang Experimental CollaboraTive ARchitecture (NECTAR) has been developed. The objective is to support multi-user collaboration in a virtual environment with an emphasis on cost-effectiveness and

MCNP SIMULATION OF THE HP(10) ENERGY RESPONSE OF A BRAZILIAN TLD ALBEDO NEUTRON INDIVIDUAL DOSEMETER, FROM THERMAL TO 20 MeV.

Science.gov (United States)

Freitas, B M; Martins, M M; Pereira, W W; da Silva, A X; Mauricio, C L P

2016-09-01

The Brazilian Instituto de Radioproteção e Dosimetria (IRD) runs a neutron individual monitoring system with a home-made TLD albedo dosemeter. It has already been characterised and calibrated in some reference fields. However, the complete energy response of this dosemeter is not known, and the calibration factors for all monitored workplace neutron fields are difficult to be obtained experimentally. Therefore, to overcome such difficulties, Monte Carlo simulations have been used. This paper describes the simulation of the HP(10) neutron response of the IRD TLD albedo dosemeter using the MCNPX transport code, for energies from thermal to 20 MeV. The validation of the MCNPX modelling is done comparing the simulated results with the experimental measurements for ISO standard neutron fields of (241)Am-Be, (252)Cf, (241)Am-B and (252)Cf(D2O) and also for (241)Am-Be source moderated with paraffin and silicone. Bare (252)Cf are used for normalisation. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The Vajont disaster: a 3D numerical simulation for the slide and the waves

Science.gov (United States)

Rubino, Angelo; Androsov, Alexey; Vacondio, Renato; Zanchettin, Davide; Voltzinger, Naum

2016-04-01

A very high resolution O(5 m), 3D hydrostatic nonlinear numerical model was used to simulate the dynamics of both the slide and the surface waves produced during the Vajont disaster (north Italy, 1963), one of the major landslide-induced tsunamis ever documented. Different simulated wave phenomena like, e.g., maximum run-up on the opposite shore, maximum height, and water velocity were analyzed and compared with data available in literature, including the results of a fully 3D simulation obtained with a Smoothed Particle Hydrodynamic code. The difference between measured and simulated after-slide bathymetries was calculated and used in an attempt to quantify the relative magnitude and extension of rigid and fluid motion components during the event.

Numerical simulation of rock cutting using 2D AUTODYN

International Nuclear Information System (INIS)

Woldemichael, D E; Rani, A M Abdul; Lemma, T A; Altaf, K

2015-01-01

In a drilling process for oil and gas exploration, understanding of the interaction between the cutting tool and the rock is important for optimization of the drilling process using polycrystalline diamond compact (PDC) cutters. In this study the finite element method in ANSYS AUTODYN-2D is used to simulate the dynamics of cutter rock interaction, rock failure, and fragmentation. A two-dimensional single PDC cutter and rock model were used to simulate the orthogonal cutting process and to investigate the effect of different parameters such as depth of cut, and back rake angle on two types of rocks (sandstone and limestone). In the simulation, the cutting tool was dragged against stationary rock at predetermined linear velocity and the depth of cut (1,2, and 3 mm) and the back rake angles(-10°, 0°, and +10°) were varied. The simulation result shows that the +10° back rake angle results in higher rate of penetration (ROP). Increasing depth of cut leads to higher ROP at the cost of higher cutting force. (paper)

50 CFR 660.25 - Permits.

Science.gov (United States)

2010-10-01

... change and the reasons for the request. If the permit requested to be changed to the base permit is..., vessel owner, or permit owner for any reason. The sablefish at-sea processing exemption will expire upon... ownership. (G) For a request to change a permit's ownership that is necessitated by divorce, the individual...

openQ*D simulation code for QCD+QED

Science.gov (United States)

Campos, Isabel; Fritzsch, Patrick; Hansen, Martin; Krstić Marinković, Marina; Patella, Agostino; Ramos, Alberto; Tantalo, Nazario

2018-03-01

The openQ*D code for the simulation of QCD+QED with C* boundary conditions is presented. This code is based on openQCD-1.6, from which it inherits the core features that ensure its efficiency: the locally-deflated SAP-preconditioned GCR solver, the twisted-mass frequency splitting of the fermion action, the multilevel integrator, the 4th order OMF integrator, the SSE/AVX intrinsics, etc. The photon field is treated as fully dynamical and C* boundary conditions can be chosen in the spatial directions. We discuss the main features of openQ*D, and we show basic test results and performance analysis. An alpha version of this code is publicly available and can be downloaded from http://rcstar.web.cern.ch/.

Simulation of stevedoring work in the Klaipėda oil terminal

Directory of Open Access Journals (Sweden)

D. Makackas

2002-10-01

Full Text Available The paper presents the approach of developing simulation models of stevedoring work in oil terminal using aggregate approach and simulation system ARENA. Aggregate approach permits to develop formal specification of simulated systems. Aggregate specification of the system is presented as a set of interacting piece-linear aggregates. Controlling sequences are used for formal description of each piece-linear aggregate. Transformation of aggregate formal specification to ARENA system operators permits to develop a simulation model. The developed model permits to evaluate characteristics of the Klaipėda oil terminal which are used both in queuing theory and analysing timing properties of real-time systems.

41 CFR 102-74.500 - Can Federal agencies disapprove permit applications or cancel issued permits?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Can Federal agencies disapprove permit applications or cancel issued permits? 102-74.500 Section 102-74.500 Public Contracts and... cancel issued permits? Yes, Federal agencies may disapprove any permit application or cancel an issued...

Generating classes of 3D virtual mandibles for AR-based medical simulation.

Science.gov (United States)

Hippalgaonkar, Neha R; Sider, Alexa D; Hamza-Lup, Felix G; Santhanam, Anand P; Jaganathan, Bala; Imielinska, Celina; Rolland, Jannick P

2008-01-01

Simulation and modeling represent promising tools for several application domains from engineering to forensic science and medicine. Advances in 3D imaging technology convey paradigms such as augmented reality (AR) and mixed reality inside promising simulation tools for the training industry. Motivated by the requirement for superimposing anatomically correct 3D models on a human patient simulator (HPS) and visualizing them in an AR environment, the purpose of this research effort was to develop and validate a method for scaling a source human mandible to a target human mandible within a 2 mm root mean square (RMS) error. Results show that, given a distance between 2 same landmarks on 2 different mandibles, a relative scaling factor may be computed. Using this scaling factor, results show that a 3D virtual mandible model can be made morphometrically equivalent to a real target-specific mandible within a 1.30 mm RMS error. The virtual mandible may be further used as a reference target for registering other anatomic models, such as the lungs, on the HPS. Such registration will be made possible by physical constraints among the mandible and the spinal column in the horizontal normal rest position.

Simulation of substrate degradation in composting of sewage sludge

International Nuclear Information System (INIS)

Zhang Jun; Gao Ding; Chen Tongbin; Zheng Guodi; Chen Jun; Ma Chuang; Guo Songlin; Du Wei

2010-01-01

To simulate the substrate degradation kinetics of the composting process, this paper develops a mathematical model with a first-order reaction assumption and heat/mass balance equations. A pilot-scale composting test with a mixture of sewage sludge and wheat straw was conducted in an insulated reactor. The BVS (biodegradable volatile solids) degradation process, matrix mass, MC (moisture content), DM (dry matter) and VS (volatile solid) were simulated numerically by the model and experimental data. The numerical simulation offered a method for simulating k (the first-order rate constant) and estimating k 20 (the first-order rate constant at 20 o C). After comparison with experimental values, the relative error of the simulation value of the mass of the compost at maturity was 0.22%, MC 2.9%, DM 4.9% and VS 5.2%, which mean that the simulation is a good fit. The k of sewage sludge was simulated, and k 20 , k 20s (first-order rate coefficient of slow fraction of BVS at 20 o C) of the sewage sludge were estimated as 0.082 and 0.015 d -1 , respectively.

Simulating the 3-D Structure of Titan's Upper Atmosphere

Science.gov (United States)

Bell, J. M.; Waite, H.; Westlake, J.; Magee, B.

2009-05-01

We present results from the 3-D Titan Global Ionosphere-Thermosphere Model (Bell et al [2009], PSS, in review). We show comparisons between simulated N2, CH4, and H2 density fields and the in-situ data from the Cassini Ion Neutral Mass Spectrometer (INMS). We describe the temperature and wind fields consistent with these density calculations. Variations with local time, longitude, and latitude will be addressed. Potential plasma heating sources can be estimated using the 1-D model of De La Haye et al [2007, 2008] and the impacts on the thermosphere of Titan can be assessed in a global sense in Titan-GITM. Lastly, we will place these findings within the context of recent work in modeling the 2-D structure of Titan's upper atmosphere (Mueller-Wodarg et al [2008]).

Using 3D Printing (Additive Manufacturing) to Produce Low-Cost Simulation Models for Medical Training.

Science.gov (United States)

Lichtenberger, John P; Tatum, Peter S; Gada, Satyen; Wyn, Mark; Ho, Vincent B; Liacouras, Peter

2018-03-01

This work describes customized, task-specific simulation models derived from 3D printing in clinical settings and medical professional training programs. Simulation models/task trainers have an array of purposes and desired achievements for the trainee, defining that these are the first step in the production process. After this purpose is defined, computer-aided design and 3D printing (additive manufacturing) are used to create a customized anatomical model. Simulation models then undergo initial in-house testing by medical specialists followed by a larger scale beta testing. Feedback is acquired, via surveys, to validate effectiveness and to guide or determine if any future modifications and/or improvements are necessary. Numerous custom simulation models have been successfully completed with resulting task trainers designed for procedures, including removal of ocular foreign bodies, ultrasound-guided joint injections, nerve block injections, and various suturing and reconstruction procedures. These task trainers have been frequently utilized in the delivery of simulation-based training with increasing demand. 3D printing has been integral to the production of limited-quantity, low-cost simulation models across a variety of medical specialties. In general, production cost is a small fraction of a commercial, generic simulation model, if available. These simulation and training models are customized to the educational need and serve an integral role in the education of our military health professionals.

3D Simulation of Multiple Simultaneous Hydraulic Fractures with Different Initial Lengths in Rock

Science.gov (United States)

Tang, X.; Rayudu, N. M.; Singh, G.

2017-12-01

Hydraulic fracturing is widely used technique for extracting shale gas. During this process, fractures with various initial lengths are induced in rock mass with hydraulic pressure. Understanding the mechanism of propagation and interaction between these induced hydraulic cracks is critical for optimizing the fracking process. In this work, numerical results are presented for investigating the effect of in-situ parameters and fluid properties on growth and interaction of multi simultaneous hydraulic fractures. A fully coupled 3D fracture simulator, TOUGH- GFEM is used for simulating the effect of different vital parameters, including in-situ stress, initial fracture length, fracture spacing, fluid viscosity and flow rate on induced hydraulic fractures growth. This TOUGH-GFEM simulator is based on 3D finite volume method (FVM) and partition of unity element method (PUM). Displacement correlation method (DCM) is used for calculating multi - mode (Mode I, II, III) stress intensity factors. Maximum principal stress criteria is used for crack propagation. Key words: hydraulic fracturing, TOUGH, partition of unity element method , displacement correlation method, 3D fracturing simulator

Electro-thermal analysis and optimisation of edge termination of power diode supported by 2-D/3-D numerical modelling and simulation

International Nuclear Information System (INIS)

Príbytný, P; Donoval, D; Chvála, A; Marek, J; Molnár, M

2014-01-01

Numerical modelling and simulation provide an efficient tool for analysis and optimization of device structure design. In this paper we present the analysis and the geometry optimization of the power module with high power pin diode structure supported by the advanced 2-D/3-D mixed-mode electro-thermal device simulation. The structure under investigation is P + NN + power diode device designed for high reverse voltages and very high forward currents, with a maximum forward surge current up to 2.7 kA.

Title V Permitting Statistics Inventory

Data.gov (United States)

U.S. Environmental Protection Agency — The Title V Permitting Statistics Inventory contains measured and estimated nationwide statistical data, consisting of counts of permitted sources, types of permits...

MATLAB simulation software used for the PhD thesis "Acquisition of Multi-Band Signals via Compressed Sensing

DEFF Research Database (Denmark)

2014-01-01

MATLAB simulation software used for the PhD thesis "Acquisition of Multi-Band Signals via Compressed Sensing......MATLAB simulation software used for the PhD thesis "Acquisition of Multi-Band Signals via Compressed Sensing...

Cerebral Aneurysm Clipping Surgery Simulation Using Patient-Specific 3D Printing and Silicone Casting.

Science.gov (United States)

Ryan, Justin R; Almefty, Kaith K; Nakaji, Peter; Frakes, David H

2016-04-01

Neurosurgery simulator development is growing as practitioners recognize the need for improved instructional and rehearsal platforms to improve procedural skills and patient care. In addition, changes in practice patterns have decreased the volume of specific cases, such as aneurysm clippings, which reduces the opportunity for operating room experience. The authors developed a hands-on, dimensionally accurate model for aneurysm clipping using patient-derived anatomic data and three-dimensional (3D) printing. Design of the model focused on reproducibility as well as adaptability to new patient geometry. A modular, reproducible, and patient-derived medical simulacrum was developed for medical learners to practice aneurysmal clipping procedures. Various forms of 3D printing were used to develop a geometrically accurate cranium and vascular tree featuring 9 patient-derived aneurysms. 3D printing in conjunction with elastomeric casting was leveraged to achieve a patient-derived brain model with tactile properties not yet available from commercial 3D printing technology. An educational pilot study was performed to gauge simulation efficacy. Through the novel manufacturing process, a patient-derived simulacrum was developed for neurovascular surgical simulation. A follow-up qualitative study suggests potential to enhance current educational programs; assessments support the efficacy of the simulacrum. The proposed aneurysm clipping simulator has the potential to improve learning experiences in surgical environment. 3D printing and elastomeric casting can produce patient-derived models for a dynamic learning environment that add value to surgical training and preparation. Copyright © 2016 Elsevier Inc. All rights reserved.

Guidance for writing permits for the use or disposal of sewage sludge. Draft report

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

Section 405(d) of the Clean Water Act (CWA) directs the U.S. Environmental Protection Agency (EPA) to develop regulations containing guidelines for the use and disposal of sewage sludge. On February 19th, 1993, EPA published final regulations at 40 Code of Federal Regulations (CFR) Part 503 as the culmination of a major effort to develop technical standards in response to Section 405(d). These regulations govern three sewage sludge use and disposal practices: land application, surface disposal, and incineration. A key element in EPA's implementation of the Part 503 regulations is educating Agency and State personnel about these new requirements. Although the regulations are generally directly enforceable against all persons involved in the use and disposal of sewage sludge, they will also be implemented through permits issued to treatment works treating domestic sewage as defined in 40 CFR 122.22. Thus, the primary focus of the manual is to assist permit writers in incorporating the Part 503 requirements into permits; it serves as an update to the Guidance for Writing Case-by-Case Permit Conditions for Municipal Sewage Sludge (PB91-145508/HDM).

Developing R&D portfolio business validity simulation model and system.

Science.gov (United States)

Yeo, Hyun Jin; Im, Kwang Hyuk

2015-01-01

The R&D has been recognized as critical method to take competitiveness by not only companies but also nations with its value creation such as patent value and new product. Therefore, R&D has been a decision maker's burden in that it is hard to decide how much money to invest, how long time one should spend, and what technology to develop which means it accompanies resources such as budget, time, and manpower. Although there are diverse researches about R&D evaluation, business factors are not concerned enough because almost all previous studies are technology oriented evaluation with one R&D technology based. In that, we early proposed R&D business aspect evaluation model which consists of nine business model components. In this research, we develop a simulation model and system evaluating a company or industry's R&D portfolio with business model point of view and clarify default and control parameters to facilitate evaluator's business validity work in each evaluation module by integrate to one screen.

2D full-wave simulation of waves in space and tokamak plasmas

Directory of Open Access Journals (Sweden)

Kim Eun-Hwa

2017-01-01

Full Text Available Simulation results using a 2D full-wave code (FW2D for space and NSTX fusion plasmas are presented. The FW2D code solves the cold plasma wave equations using the finite element method. The wave code has been successfully applied to describe low frequency waves in planetary magnetospheres (i.e., dipole geometry and the results include generation and propagation of externally driven ultra-low frequency waves via mode conversion at Mercury and mode coupling, refraction and reflection of internally driven field-aligned propagating left-handed electromagnetic ion cyclotron (EMIC waves at Earth. In this paper, global structure of linearly polarized EMIC waves is examined and the result shows such resonant wave modes can be localized near the equatorial plane. We also adopt the FW2D code to tokamak geometry and examine radio frequency (RF waves in the scape-off layer (SOL of tokamaks. By adopting the rectangular and limiter boundary, we compare the results with existing AORSA simulations. The FW2D code results for the high harmonic fast wave heating case on NSTX with a rectangular vessel boundary shows excellent agreement with the AORSA code.

2D full-wave simulation of waves in space and tokamak plasmas

Science.gov (United States)

Kim, Eun-Hwa; Bertelli, Nicola; Johnson, Jay; Valeo, Ernest; Hosea, Joel

2017-10-01

Simulation results using a 2D full-wave code (FW2D) for space and NSTX fusion plasmas are presented. The FW2D code solves the cold plasma wave equations using the finite element method. The wave code has been successfully applied to describe low frequency waves in planetary magnetospheres (i.e., dipole geometry) and the results include generation and propagation of externally driven ultra-low frequency waves via mode conversion at Mercury and mode coupling, refraction and reflection of internally driven field-aligned propagating left-handed electromagnetic ion cyclotron (EMIC) waves at Earth. In this paper, global structure of linearly polarized EMIC waves is examined and the result shows such resonant wave modes can be localized near the equatorial plane. We also adopt the FW2D code to tokamak geometry and examine radio frequency (RF) waves in the scape-off layer (SOL) of tokamaks. By adopting the rectangular and limiter boundary, we compare the results with existing AORSA simulations. The FW2D code results for the high harmonic fast wave heating case on NSTX with a rectangular vessel boundary shows excellent agreement with the AORSA code.

3D finite element simulation of optical modes in VCSELs

OpenAIRE

Rozova, M.; Pomplun, J.; Zschiedrich, L.; Schmidt, F.; Burger, S.

2011-01-01

We present a finite element method (FEM) solver for computation of optical resonance modes in VCSELs. We perform a convergence study and demonstrate that high accuracies for 3D setups can be attained on standard computers. We also demonstrate simulations of thermo-optical effects in VCSELs.

MuSim, a Graphical User Interface for Multiple Simulation Programs

Energy Technology Data Exchange (ETDEWEB)

Roberts, Thomas [MUONS Inc., Batavia; Cummings, Mary Anne [MUONS Inc., Batavia; Johnson, Rolland [MUONS Inc., Batavia; Neuffer, David [Fermilab

2016-06-01

MuSim is a new user-friendly program designed to interface to many different particle simulation codes, regardless of their data formats or geometry descriptions. It presents the user with a compelling graphical user interface that includes a flexible 3-D view of the simulated world plus powerful editing and drag-and-drop capabilities. All aspects of the design can be parametrized so that parameter scans and optimizations are easy. It is simple to create plots and display events in the 3-D viewer (with a slider to vary the transparency of solids), allowing for an effortless comparison of different simulation codes. Simulation codes: G4beamline, MAD-X, and MCNP; more coming. Many accelerator design tools and beam optics codes were written long ago, with primitive user interfaces by today's standards. MuSim is specifically designed to make it easy to interface to such codes, providing a common user experience for all, and permitting the construction and exploration of models with very little overhead. For today's technology-driven students, graphical interfaces meet their expectations far better than text-based tools, and education in accelerator physics is one of our primary goals.

50 CFR 18.31 - Scientific research permits and public display permits.

Science.gov (United States)

2010-10-01

... the population stock and the marine ecosystem. In determining whether to issue a public display permit... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Scientific research permits and public..., DEPARTMENT OF THE INTERIOR (CONTINUED) TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER...

Thermal large Eddy simulations and experiments in the framework of non-isothermal blowing; Simulations des grandes echelles thermiques et experiences dans le cadre d'effusion anisotherme

Energy Technology Data Exchange (ETDEWEB)

Brillant, G

2004-06-15

The aim of this work is to study thermal large-eddy simulations and to determine the nonisothermal blowing impact on a turbulent boundary layer. An experimental study is also carried out in order to complete and validate simulation results. In a first time, we developed a turbulent inlet condition for the velocity and the temperature, which is necessary for the blowing simulations.We studied the asymptotic behavior of the velocity, the temperature and the thermal turbulent fluxes in a large-eddy simulation point of view. We then considered dynamics models for the eddy-diffusivity and we simulated a turbulent channel flow with imposed temperature, imposed flux and adiabatic walls. The numerical and experimental study of blowing permitted to obtain to the modifications of a thermal turbulent boundary layer with the blowing rate. We observed the consequences of the blowing on mean and rms profiles of velocity and temperature but also on velocity-velocity and velocity-temperature correlations. Moreover, we noticed an increase of the turbulent structures in the boundary layer with blowing. (author)

3D segmentation of scintigraphic images with validation on realistic GATE simulations

International Nuclear Information System (INIS)

Burg, Samuel

2011-01-01

The objective of this thesis was to propose a new 3D segmentation method for scintigraphic imaging. The first part of the work was to simulate 3D volumes with known ground truth in order to validate a segmentation method over other. Monte-Carlo simulations were performed using the GATE software (Geant4 Application for Emission Tomography). For this, we characterized and modeled the gamma camera 'γ Imager' Biospace"T"M by comparing each measurement from a simulated acquisition to his real equivalent. The 'low level' segmentation tool that we have developed is based on a modeling of the levels of the image by probabilistic mixtures. Parameters estimation is done by an SEM algorithm (Stochastic Expectation Maximization). The 3D volume segmentation is achieved by an ICM algorithm (Iterative Conditional Mode). We compared the segmentation based on Gaussian and Poisson mixtures to segmentation by thresholding on the simulated volumes. This showed the relevance of the segmentations obtained using probabilistic mixtures, especially those obtained with Poisson mixtures. Those one has been used to segment real "1"8FDG PET images of the brain and to compute descriptive statistics of the different tissues. In order to obtain a 'high level' segmentation method and find anatomical structures (necrotic part or active part of a tumor, for example), we proposed a process based on the point processes formalism. A feasibility study has yielded very encouraging results. (author) [fr

3D TCAD Simulation for Semiconductor Processes, Devices and Optoelectronics

CERN Document Server

Li, Simon

2012-01-01

Technology computer-aided design, or TCAD, is critical to today’s semiconductor technology and anybody working in this industry needs to know something about TCAD.  This book is about how to use computer software to manufacture and test virtually semiconductor devices in 3D.  It brings to life the topic of semiconductor device physics, with a hands-on, tutorial approach that de-emphasizes abstract physics and equations and emphasizes real practice and extensive illustrations.  Coverage includes a comprehensive library of devices, representing the state of the art technology, such as SuperJunction LDMOS, GaN LED devices, etc. Provides a vivid, internal view of semiconductor devices, through 3D TCAD simulation; Includes comprehensive coverage of  TCAD simulations for both optic and electronic devices, from nano-scale to high-voltage high-power devices; Presents material in a hands-on, tutorial fashion so that industry practitioners will find maximum utility; Includes a comprehensive library of devices, re...

Hanford Facility RCRA permit handbook

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Purpose of this Hanford Facility (HF) RCRA Permit Handbook is to provide, in one document, information to be used for clarification of permit conditions and guidance for implementing the HF RCRA Permit.

Numerical simulation of 3D boundary-driven acoustic streaming in microfluidic devices.

Science.gov (United States)

Lei, Junjun; Hill, Martyn; Glynne-Jones, Peter

2014-02-07

This article discusses three-dimensional (3D) boundary-driven streaming in acoustofluidic devices. Firstly, the 3D Rayleigh streaming pattern in a microchannel is simulated and its effect on the movement of microparticles of various sizes is demonstrated. The results obtained from this model show good comparisons with 3D experimental visualisations and demonstrate the fully 3D nature of the acoustic streaming field and the associated acoustophoretic motion of microparticles in acoustofluidic devices. This method is then applied to another acoustofluidic device in order to gain insights into an unusual in-plane streaming pattern. The origin of this streaming has not been fully described and its characteristics cannot be explained from the classical theory of Rayleigh streaming. The simulated in-plane streaming pattern was in good agreement with the experimental visualisation. The mechanism behind it is shown to be related to the active sound intensity field, which supports our previous findings on the mechanism of the in-plane acoustic streaming pattern visualised and modelled in a thin-layered capillary device.

Correspondence model-based 4D VMAT dose simulation for analysis of local metastasis recurrence after extracranial SBRT

Science.gov (United States)

Sothmann, T.; Gauer, T.; Wilms, M.; Werner, R.

2017-12-01

The purpose of this study is to introduce a novel approach to incorporate patient-specific breathing variability information into 4D dose simulation of volumetric arc therapy (VMAT)-based stereotactic body radiotherapy (SBRT) of extracranial metastases. Feasibility of the approach is illustrated by application to treatment planning and motion data of lung and liver metastasis patients. The novel 4D dose simulation approach makes use of a regression-based correspondence model that allows representing patient motion variability by breathing signal-steered interpolation and extrapolation of deformable image registration motion fields. To predict the internal patient motion during treatment with only external breathing signal measurements being available, the patients’ internal motion information and external breathing signals acquired during 4D CT imaging were correlated. Combining the correspondence model, patient-specific breathing signal measurements during treatment and time-resolved information about dose delivery, reconstruction of a motion variability-affected dose becomes possible. As a proof of concept, the proposed approach is illustrated by a retrospective 4D simulation of VMAT-based SBRT treatment of ten patients with 15 treated lung and liver metastases and known clinical endpoints for the individual metastases (local metastasis recurrence yes/no). Resulting 4D-simulated dose distributions were compared to motion-affected dose distributions estimated by standard 4D CT-only dose accumulation and the originally (i.e. statically) planned dose distributions by means of GTV D98 indices (dose to 98% of the GTV volume). A potential linkage of metastasis-specific endpoints to differences between GTV D98 indices of planned and 4D-simulated dose distributions was analyzed.

Computational steering of GEM based detector simulations

Science.gov (United States)

Sheharyar, Ali; Bouhali, Othmane

2017-10-01

Gas based detector R&D relies heavily on full simulation of detectors and their optimization before final prototypes can be built and tested. These simulations in particular those with complex scenarios such as those involving high detector voltages or gas with larger gains are computationally intensive may take several days or weeks to complete. These long-running simulations usually run on the high-performance computers in batch mode. If the results lead to unexpected behavior, then the simulation might be rerun with different parameters. However, the simulations (or jobs) may have to wait in a queue until they get a chance to run again because the supercomputer is a shared resource that maintains a queue of other user programs as well and executes them as time and priorities permit. It may result in inefficient resource utilization and increase in the turnaround time for the scientific experiment. To overcome this issue, the monitoring of the behavior of a simulation, while it is running (or live), is essential. In this work, we employ the computational steering technique by coupling the detector simulations with a visualization package named VisIt to enable the exploration of the live data as it is produced by the simulation.

The Effects of 3D Computer Simulation on Biology Students' Achievement and Memory Retention