Conflict, location, and politics: Siting a nuclear waste repository

International Nuclear Information System (INIS)

Jacob, G.R.

1988-01-01

Nuclear power and the management of high-level radioactive waste is examined with the goal of explaining the forces driving the formulation of the 1982 Nuclear Waste Policy Act and a subsequent decision to site a nuclear waste repository at Yucca Mountain, Nevada. The study draws upon geographic, political, economic, and organizational factors to examine the commitment to dispose of spent fuel in a geologic repository located in Nevada or in Utah, Texas, Mississippi, Louisiana, or at Hanford Washington. Special attention is given to the impact of location, science and technology on the definition of the nuclear waste problem and political agendas, public participation, and the power of the nuclear establishment. The study finds that the choice of a Yucca Mountain Nevada as the preferred site for a repository was based more on technological precedent and political-economic expediency than on the demonstrated superiority of that site's geology. Conflict over a repository location is interpreted as a symptom of more fundamental conflicts concerning: the credibility of nuclear science, the legitimacy of federal authority and administration, and the priorities of environmental protection and a nuclear economy

Analysis on one underground nuclear waste repository rock mass in USA

International Nuclear Information System (INIS)

Ha Qiuling; Zhang Tiantian

2012-01-01

When analyzing the rock mass of a underground nuclear waste repository, the current studies are all based on the loading mechanical condition, and the unloading damage of rock mass is unconsidered. According to the different mechanical condition of actual engineering rock mass of loading and unloading, this paper implements a comprehensive analysis on the rock mass deformation of underground nuclear waste repository through the combination of present loading and unloading rock mass mechanics. It is found that the results of comprehensive analysis and actual measured data on the rock mass deformation of underground nuclear waste repository are basically the same, which provide supporting data for the underground nuclear waste repository. (authors)

Global nuclear waste repository proposal highlights Australia's nuclear energy vacuum

International Nuclear Information System (INIS)

Anon.

1999-01-01

The Pangea proposal is disscused and considered relevant to Australia. A five-year research program by the company has identified Australia and Argentina as having the appropriate geological, economic and democratic credentials for such a deep repository, with Australia being favoured. A deep repository would be located where the geology has been stable for several hundred million years, so that there need not be total reliance on a robust engineered barrier system to keep the waste securely isolated for thousands of years. It would be a commercial undertaking and would have dedicated port and rail infrastructure. It would take spent fuel and other wastes from commercial reactors, and possibly also waste from weapons disposal programs. Clearly, while the primary ethical and legal principle is that each country is entirely responsible for its own waste, including nuclear waste (polluter pays etc), the big question is whether the concept of an international waste repository is acceptable ethically. Political and economic questions are secondary to this. By taking a fresh look at the reasons for the difficulties which have faced most national repository programs, and discarding the preconception that each country must develop its own disposal facilities, it is possible to define a class of simple, superior high isolation sites which may provide a multi-national basis for solving the nuclear waste disposal problem. The relatively small volumes of high-level wastes or spent fuel which arise from nuclear power production make shared repositories a feasible proposition. For small countries, the economies of scale which can be achieved make the concept attractive. For all countries, objective consideration of the relative merits of national and multi-national solutions is a prudent part of planning the management of long-lived radioactive wastes

International high-level radioactive waste repositories

International Nuclear Information System (INIS)

Lin, W.

1996-01-01

Although nuclear technologies benefit everyone, the associated nuclear wastes are a widespread and rapidly growing problem. Nuclear power plants are in operation in 25 countries, and are under construction in others. Developing countries are hungry for electricity to promote economic growth; industrialized countries are eager to export nuclear technologies and equipment. These two ingredients, combined with the rapid shrinkage of worldwide fossil fuel reserves, will increase the utilization of nuclear power. All countries utilizing nuclear power produce at least a few tens of tons of spent fuel per year. That spent fuel (and reprocessing products, if any) constitutes high-level nuclear waste. Toxicity, long half-life, and immunity to chemical degradation make such waste an almost permanent threat to human beings. This report discusses the advantages of utilizing repositories for disposal of nuclear wastes

A conceptual subsurface facility design for a high-level nuclear waste repository at Yucca Mountain

International Nuclear Information System (INIS)

McKenzie, D.G., III; Bhattacharyya, K.K.; Segrest, A.M.

1996-01-01

The US Department of Energy is responsible for the design, construction, operation and closure of a repository in which to permanently dispose of the nation's high level nuclear waste. In addition to the objective of safely isolating the waste inventory, the repository must provide a safe working environment for its workforce, and protect the public. The conceptual design for this facility is currently being developed. Tunnel Boring Machine will be used to excavate 228 kilometers of tunneling to construct the facility over a 30 year period. The excavation operations will be physically separated from the waste emplacement operations, and each operation will have its own dedicated ventilation system. The facility is being designed to remain open for 150 years

Nuclear waste in a repository: amount as a factor in risk duration

International Nuclear Information System (INIS)

Zen, E.

1980-01-01

The relationship between the amount of nuclear waste in a nuclear repository and the safety of the repository is examined. It is shown that the amount of a given hazardous nuclide that is potentially leachable depends on the initial amount of waste in the repository and the time that has elapsed since the repository was put into operation. Nuclear repository safety can be enhanced if repositories are designed as modular units with leach-resistant watertight compartments

Preliminary concepts: materials management in an internationally safeguarded nuclear-waste geologic repository

International Nuclear Information System (INIS)

Ostenak, C.A.; Whitty, W.J.; Dietz, R.J.

1979-11-01

Preliminary concepts of materials accountability are presented for an internationally safeguarded nuclear-waste geologic repository. A hypothetical reference repository that receives nuclear waste for emplacement in a geologic medium serves to illustrate specific safeguards concepts. Nuclear wastes received at the reference repository derive from prior fuel-cycle operations. Alternative safeguards techniques ranging from item accounting to nondestructive assay and waste characteristics that affect the necessary level of safeguards are examined. Downgrading of safeguards prior to shipment to the repository is recommended whenever possible. The point in the waste cycle where international safeguards may be terminate depends on the fissile content, feasibility of separation, and practicable recoverability of the waste: termination may not be possible if spent fuels are declared as waste

Global nuclear waste repository proposal highlights Australia`s nuclear energy vacuum

Energy Technology Data Exchange (ETDEWEB)

Anon.

1999-06-01

The Pangea proposal is disscused and considered relevant to Australia. A five-year research program by the company has identified Australia and Argentina as having the appropriate geological, economic and democratic credentials for such a deep repository, with Australia being favoured. A deep repository would be located where the geology has been stable for several hundred million years, so that there need not be total reliance on a robust engineered barrier system to keep the waste securely isolated for thousands of years. It would be a commercial undertaking and would have dedicated port and rail infrastructure. It would take spent fuel and other wastes from commercial reactors, and possibly also waste from weapons disposal programs. Clearly, while the primary ethical and legal principle is that each country is entirely responsible for its own waste, including nuclear waste (polluter pays etc), the big question is whether the concept of an international waste repository is acceptable ethically. Political and economic questions are secondary to this. By taking a fresh look at the reasons for the difficulties which have faced most national repository programs, and discarding the preconception that each country must develop its own disposal facilities, it is possible to define a class of simple, superior high isolation sites which may provide a multi-national basis for solving the nuclear waste disposal problem. The relatively small volumes of high-level wastes or spent fuel which arise from nuclear power production make shared repositories a feasible proposition. For small countries, the economies of scale which can be achieved make the concept attractive. For all countries, objective consideration of the relative merits of national and multi-national solutions is a prudent part of planning the management of long-lived radioactive wastes

Citizen participation in nuclear waste repository siting

International Nuclear Information System (INIS)

Howell, R.E.; Olsen, D.

1982-12-01

The following study presents a proposed strategy for citizen participation during the planning stages of nuclear waste repository siting. It discusses the issue from the general perspective of citizen participation in controversial issues and in community development. Second, rural institutions and attitudes toward energy development as the context for developing a citizen participation program are examined. Third, major citizen participation techniques and the advantages and disadvantages of each approach for resolving public policy issues are evaluated. Fourth, principles of successful citizen participation are presented. Finally, a proposal for stimulating and sustaining effective responsible citizen participation in nuclear waste repository siting and management is developed

Commercial nuclear waste repository in basalt

International Nuclear Information System (INIS)

Hardy, M.P.; Patricio, J.G.; Heley, W.H.

1980-06-01

The Basalt Waste Isolation Project (BWIP) is an ongoing research and engineering effort being conducted by Rockwell Hanford Operations (Rockwell), which is under contract to the US Department of Energy. The objectives of this program are to assess the feasibility of and to provide the technology needed to design and construct a licensed commercial nuclear waste repository in the deep basalt formations underlying the Hanford Site. An extensive preconceptual design effort was undertaken during 1979 to develop a feasible concept that could serve as a reference design for both surface and underground facilities. The preconceptual design utilized existing technology to the greatest extent possible to offer a system design that could be utilized in establishing schedule and cost baseline data, recommend alternatives that require additional study, and develop basic design requirements that would allow evolution of the design process prior to the existence of legislated criteria. This paper provides a description of the concept developed for the subsurface aspects of this nuclear waste repository

Safe disposal of radioactive waste. Post-closure safety assessment of permanent repository in Novi han

International Nuclear Information System (INIS)

Mateeva, M.

2007-01-01

A presented material is the third part of the monograph with title 'Safe disposal of radioactive waste. Post-closure safety assessment of the permanent repository in Novi Han'. This part deals with review of the scenario selection procedure. The process system of permanent repository for radioactive waste is describing in details for different levels. Preliminary screening process of features, events and processes is presented here. Interaction matrixes for basic disposal system components are constructed. Final selection and grouping between the included features, events and processes is done. Selected and defined scenarios for post-closure safety assessment are presented too. Key words: post-closure safety assessment, scenario generation procedure, process system, process influence diagram, and interaction matrix

Supply-side approach to nuclear waste repositories

International Nuclear Information System (INIS)

Harmon, L.H.

1985-01-01

The Nuclear Waste Policy Act of 1982 (NWPA) was signed into law on January 7, 1983. Its purpose was to provide for the development of repositories for the disposal of high-level radioactive waste and spent nuclear fuel, to establish a program of research, development, and demonstration regarding the disposal of high-level radioactive waste and spent nuclear fuel, and for other purposes. Its goal is to have the first waste repository operational by 1998. It is believed by many that this goal cannot possibly be met. The Act is exceedingly complex with something in it for everybody. There are serious impediments to the program - not the least of which is legislation itself. The process will cost tens of billions of dollars and, even if it does succeed, will take many years to accomplish. This paper proposes a method for getting there in 7 years while saving billions of dollars. It is a summary of a more extensive research effort by the author while attending the Industrial College of the Armed Forces

Modeling by GASP-IV simulation of high-level nuclear waste disposal

International Nuclear Information System (INIS)

Kurstedt, H.A. Jr.; DePorter, E.L.; Turek, J.L.; Funk, S.K.; Rasbach, C.E.

1981-01-01

High-level nuclear waste generated by defense-oriented and commercial nuclear energy activities are to be stored ultimately in underground repositories. Research continues on the waste-form and waste-form processing. DOE managers must coordinate the results of this research, the capacities and availability times of the permanent geologic storage repositories, and the capacities and availability times of interim storage facilities (pending availability of permanent repositories). Comprehensive and active DOE program-management information systems contain predicted generation of nuclear wastes from defense and commercial activities; milestones on research on waste-forms; and milestones on research and development, design, acquisition, and construction of facilities and repositories. A GASP IV simulation model is presented which interfaces all of these data. The model accepts alternate management decisions; relates all critical milestones, all research and development data, and the generation of waste nuclear materials; simulates the passage of time; then, predicts the impact of those alternate decisions on the availability of storage capacity for waste nuclear materials. 3 references, 3 figures

Permanent Disposal of Nuclear Waste in Salt

Science.gov (United States)

Hansen, F. D.

2016-12-01

Salt formations hold promise for eternal removal of nuclear waste from our biosphere. Germany and the United States have ample salt formations for this purpose, ranging from flat-bedded formations to geologically mature dome structures. Both nations are revisiting nuclear waste disposal options, accompanied by extensive collaboration on applied salt repository research, design, and operation. Salt formations provide isolation while geotechnical barriers reestablish impermeability after waste is placed in the geology. Between excavation and closure, physical, mechanical, thermal, chemical, and hydrological processes ensue. Salt response over a range of stress and temperature has been characterized for decades. Research practices employ refined test techniques and controls, which improve parameter assessment for features of the constitutive models. Extraordinary computational capabilities require exacting understanding of laboratory measurements and objective interpretation of modeling results. A repository for heat-generative nuclear waste provides an engineering challenge beyond common experience. Long-term evolution of the underground setting is precluded from direct observation or measurement. Therefore, analogues and modeling predictions are necessary to establish enduring safety functions. A strong case for granular salt reconsolidation and a focused research agenda support salt repository concepts that include safety-by-design. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. Author: F. D. Hansen, Sandia National Laboratories

Nuclear waste issue

International Nuclear Information System (INIS)

Ryhanen, V.

2000-01-01

A prerequisite for future use of nuclear energy in electricity production is safe management of the radioactive wastes generated by nuclear power industry. A number of facilities have been constructed for different stages of nuclear waste management around the world, for example for conditioning of different kind of process wastes and for intermediate storage of spent nuclear fuel. Difficulties have often been encountered particularly when trying to advance plans for final stage of waste management, which is permanent disposal in stable geological formations. The main problems have not been technical, but poor public acceptance and lack of necessary political decisions have delayed the progress in many countries. However, final disposal facilities are already in operation for low- and medium-level nuclear wastes. The most challenging task is the development of final disposal solutions for long-lived high-level wastes (spent fuel or high-level reprocessing waste). The implementation of deep geological repositories for these wastes requires persistent programmes for technology development, siting and safety assessments, as well as for building public confidence in long-term safety of the planned repositories. Now, a few countries are proceeding towards siting of these facilities, and the first high-level waste repositories are expected to be commissioned in the years 2010 - 2020. (author)

Nuclear waste management and implication for geological disposals in South Korea

Energy Technology Data Exchange (ETDEWEB)

Woo, Tae Ho; Chang, Kyung Bae [The Cyber Univ. of Korea, Seoul (Korea, Republic of). Dept. of Mechanical and Control Engineering

2017-10-15

The master plan of permanent nuclear waste repository had been published in South Korea. The high-level nuclear waste repository should be available in 2053. In this study, six possible nuclear waste forms are simulated by Helium ions. The geological repository is comparative easy and cheap considering the international nuclear act of the nuclear nonproliferation treaty (NPT). How ever, there could be some new technologies of the nuclear waste treatment like the pyroprocessing. Transmutation is another option, which is very expensive with current technology.

Buoyancy flow in fractures intersecting a nuclear waste repository

International Nuclear Information System (INIS)

Wang, J.S.Y.; Tsang, C.F.

1980-07-01

The thermally induced buoyancy flow in fractured rocks around a nuclear waste repository is of major concern in the evaluation of the regional, long-term impact of nuclear waste disposal in geological formation. In this study, buoyancy flow and the development of convective cells are calculated in vertical fractures passing through or positioned near a repository. Interaction between buoyancy flow and regional hydraulic gradient is studied as a function of time, and the interference of intersecting fractures with each other is also discussed

A Single Global Small-User Nuclear Repository

International Nuclear Information System (INIS)

Conca, J.L.; Wright, J.

2009-01-01

Global energy partnerships in nuclear power, proposed by France, Russia, U.S. and England, seek to address the proliferation issue by controlling fuel production and nuclear materials, removing the need for each country to develop enrichment, fabrication, recycling or disposal capabilities. Several of the large generator countries such as France, the U.S., Japan, S. Korea, Russia, the U.K., China and India, all have plans for deep geologic repositories because they anticipate sufficient waste over the next century to justify the expense of a repository. However, countries having, or planning, less than five reactors, such as Egypt, Iran, Indonesia, Brazil and about 30 other countries, will not have sufficient waste generation, or a favorable geologic site, to justify the economic and environmental issues of developing their own repository. The Salado salt formation in New Mexico, set aside for nuclear waste disposal within the 16 square-mile area by the Land Withdrawal Act of 1992, is the most optimal geologic formation for the permanent disposal of any nuclear waste and is easily able to host all of the commercial nuclear waste that will be generated in the next thousand years. The U.S. commercial nuclear waste needs presently surpass all others, and will for the foreseeable future. Hosting the relatively small amount of waste from these small-user nations will add little to U.S. waste stream while the cost/benefit analysis from the standpoint of operations, safety, geology, cost and proliferation is overwhelmingly positive for developing such a global repository. Oceanic and overland transportation, high-level disposal logistics and costs from several programs, including WIPP, have demonstrated that the operation would pay for itself from international user fees with no U.S. taxpayer dollars required and still save the world about $400 billion over 100 years. The ethical considerations alone are compelling. (authors)

Nuclear waste repository transparency technology test bed demonstrations at WIPP

International Nuclear Information System (INIS)

Betsill J, David; Elkins, Ned Z.; Wu, Chuan-Fu; Mewhinney, James D.; Aamodt, Paul

2000-01-01

Secretary of Energy, Bill Richardson, has stated that one of the nuclear waste legacy issues is ''The challenge of managing the fuel cycle's back end and assuring the safe use of nuclear power.'' Waste management (i.e., the back end) is a domestic and international issue that must be addressed. A key tool in gaining acceptance of nuclear waste repository technologies is transparency. Transparency provides information to outside parties for independent assessment of safety, security, and legitimate use of materials. Transparency is a combination of technologies and processes that apply to all elements of the development, operation, and closure of a repository system. A test bed for nuclear repository transparency technologies has been proposed to develop a broad-based set of concepts and strategies for transparency monitoring of nuclear materials at the back end of the fuel/weapons cycle. WIPP is the world's first complete geologic repository system for nuclear materials at the back end of the cycle. While it is understood that WIPP does not currently require this type of transparency, this repository has been proposed as realistic demonstration site to generate and test ideas, methods, and technologies about what transparency may entail at the back end of the nuclear materials cycle, and which could be applicable to other international repository developments. An integrated set of transparency demonstrations was developed and deployed during the summer, and fall of 1999 as a proof-of-concept of the repository transparency technology concept. These demonstrations also provided valuable experience and insight into the implementation of future transparency technology development and application. These demonstrations included: Container Monitoring Rocky Flats to WIPP; Underground Container Monitoring; Real-Time Radiation and Environmental Monitoring; Integrated level of confidence in the system and information provided. As the world's only operating deep geologic

Geologic environments for nuclear waste repositories

Directory of Open Access Journals (Sweden)

Paleologos Evan K.

2017-01-01

Full Text Available High-level radioactive waste (HLW results from spent reactor fuel and reprocessed nuclear material. Since 1957 the scientific consensus is that deep geologic disposal constitutes the safest means for isolating HLW for long timescales. Nuclear power is becoming significant for the Arab Gulf countries as a way to diversify energy sources and drive economic developments. Hence, it is of interest to the UAE to examine the geologic environments currently considered internationally to guide site selection. Sweden and Finland are proceeding with deep underground repositories mined in bedrock at depths of 500m, and 400m, respectively. Equally, Canada’s proposals are deep burial in the plutonic rock masses of the Canadian Shield. Denmark and Switzerland are considering disposal of their relative small quantities of HLW into crystalline basement rocks through boreholes at depths of 5,000m. In USA, the potential repository at Yucca Mountain, Nevada lies at a depth of 300m in unsaturated layers of welded volcanic tuffs. Disposal of low and intermediate-level radioactive wastes, as well as the German HLW repository favour structurally-sound layered salt stata and domes. Our article provides a comprehensive review of the current concepts regarding HLW disposal together with some preliminary analysis of potentially appropriate geologic environments in the UAE.

Study of nuclear waste storage capacity at Yucca mountain repository

International Nuclear Information System (INIS)

Zhou Wei; Apted, M.; Kessler, J.H.

2008-01-01

The Yucca Mountain repository is applying license for storing 70000 MTHM nuclear waste including commercial spent nuclear fuel (CSNF) and defense high-level radioactive waste (HLW). The 70000 MTHM is a legal not the technical limit. To study the technical limit, the Electric Power Research Institute (EPRI) carried out a systematic study to explore the potential impact if the repository will accept more waste. This paper describes the model and results for evaluating the spent-fuel disposal capacity for a repository at Yucca Mountain from the thermal and hydrological point of view. Two proposed alternative repository designs are analyzed, both of which would fit into the currently well-characterized site and, therefore, not necessitating any additional site characterization at Yucca Mountain. The two- and three-dimensional models for coupled thermo-hydrological analysis extends from the surface to the water table, covering all the major and subgroup rock layers of the planned repository, as well as formations above and below the repository horizon. A dual-porosity and dual-permeability approach is used to model coupled heat and mass transfer through fracture formations. The waste package heating and ventilation are all assumed to follow those of the current design. The results show that the repository is able to accommodate three times the amount of spent fuel compared to the current design, without extra spatial expansion or exceeding current thermal and hydrological constraints. (authors)

Nuclear waste repository research at the micro- to nanoscale

Science.gov (United States)

Schäfer, T.; Denecke, M. A.

2010-04-01

Micro- and nano-focused synchrotron radiation techniques to investigate determinant processes in contaminant transport in geological media are becoming especially an increasingly used tool in nuclear waste disposal research. There are a number of reasons for this but primarily they are driven by the need to characterize actinide speciation localized in components of heterogeneous natural systems. We summarize some of the recent research conducted by researchers of the Institute of Nuclear Waste Disposal (INE) at the Karlsruhe Institute of Technology using micro- and nano-focused X-ray beams for characterization of colloids and their interaction with minerals and of elemental and phase distributions in potential repository host rocks and actinide speciation in a repository natural analogues sample. Such investigations are prerequisite to ensuring reliable assessment of the long term radiological safety for proposed nuclear waste disposal sites.

Constructibility issues associated with a nuclear waste repository in basalt

International Nuclear Information System (INIS)

Turner, D.A.

1981-01-01

This report contains the text and slide reproductions of a speech on nuclear waste disposal in basalt. The presentation addresses the layout of repository access shafts and subsurface facilities resulting from the conceptual design of a nuclear repository in basalt. The constructibility issues that must be resolved prior to construction are described

Retrieval effects on ventilation and cooling requirements for a nuclear waste repository

International Nuclear Information System (INIS)

Hambley, D.F.

1985-01-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) and the regulations promulgated in Title 10, Part 60 of the Code of Federal Regulations (10CFR60) by the US Nuclear Regulatory Commission (NRC) for an underground repository for spent fuel and high level nuclear waste (HLW) require that it is possible to retrieve waste, for whatever reason, from such a facility for a period of 50 years from initial storage or until the completion of the performance confirmation period, whichever comes first. This paper considers the effects that the retrievability option mandates on ventilation and cooling systems required for normal repository operations. An example is given for a hypothetical repository in salt. 18 refs., 1 tab

Nuclear waste repository in basalt: a design description

International Nuclear Information System (INIS)

Ritchie, J.S.; Schmidt, B.

1982-01-01

The conceptual design of a nuclear waste repository in basalt is described. Nuclear waste packages are placed in holes drilled into the floor of tunnels at a depth of 3700 ft. About 100 miles of tunnels are required to receive 35,000 packages. Five shafts bring waste packages, ventilation air, excavated rock, personnel, material, and services to and from the subsurface. The most important surface facility is the waste handling building, located over the waste handling shaft, where waste is received and packaged for storage. Two independent ventilation systems are provided to avoid potential contamination of spaces that do not contain nuclear waste. Because of the high temperatures at depth, an elaborate air chilling system is provided. Because the waste packages deliver a considerable amount of heat energy to the rock mass, particular attention is paid to heat transfer and thermal stress studies. 3 references, 31 figures, 3 tables

Selection of candidate canister materials for high-level nuclear waste containment in a tuff repository

International Nuclear Information System (INIS)

McCright, R.D.; Weiss, H.; Juhas, M.C.; Logan, R.W.

1983-11-01

A repository located at Yucca Mountain at the Nevada Test Site is a potential site for permanent geological disposal of high-level nuclear waste. The repository can be located in a horizon in welded tuff, a volcanic rock, which is above the static water level at this site. The environmental conditions in this unsaturated zone are expected to be air and water vapor dominated for much of the containment period. Type 304L stainless steel is the reference material for fabricating canisters to contain the solid high-level wastes. Alternative stainless alloys are considered because of possible susceptibility of 304L to localized and stress forms of corrosion. For the reprocessed glass wastes, the canisters serve as the recipient for pouring the glass with the result that a sensitized microstructure may develop because of the times at elevated temperatures. Corrosion testing of the reference and alternative materials has begun in tuff-conditioned water and steam environments. 21 references, 8 figures, 8 tables

Climate Considerations in Long-Term Safety Assessments for Nuclear Waste Repositories

Energy Technology Data Exchange (ETDEWEB)

Naeslund, Jens-Ove; Brandefelt, Jenny; Claesson Liljedahl, Lillemor [Svensk Kaernbraenslehantering AB, Stockholm (Sweden)], E-mail: jens-ove.naslund@skb.se

2013-05-15

For a deep geological repository for spent nuclear fuel planned in Sweden, the safety assessment covers up to 1 million years. Climate scenarios range from high-end global warming for the coming 100 000 years, through deep permafrost, to large ice sheets during glacial conditions. In contrast, in an existing repository for short-lived waste the activity decays to low levels within a few tens of thousands of years. The shorter assessment period, 100 000 years, requires more focus on climate development over the coming tens of thousands of years, including the earliest possibility for permafrost growth and freezing of the engineered system. The handling of climate and climate change in safety assessments must be tailor-made for each repository concept and waste type. However, due to the uncertain future climate development on these vast time scales, all safety assessments for nuclear waste repositories require a range of possible climate scenarios.

Climate considerations in long-term safety assessments for nuclear waste repositories.

Science.gov (United States)

Näslund, Jens-Ove; Brandefelt, Jenny; Liljedahl, Lillemor Claesson

2013-05-01

For a deep geological repository for spent nuclear fuel planned in Sweden, the safety assessment covers up to 1 million years. Climate scenarios range from high-end global warming for the coming 100 000 years, through deep permafrost, to large ice sheets during glacial conditions. In contrast, in an existing repository for short-lived waste the activity decays to low levels within a few tens of thousands of years. The shorter assessment period, 100 000 years, requires more focus on climate development over the coming tens of thousands of years, including the earliest possibility for permafrost growth and freezing of the engineered system. The handling of climate and climate change in safety assessments must be tailor-made for each repository concept and waste type. However, due to the uncertain future climate development on these vast time scales, all safety assessments for nuclear waste repositories require a range of possible climate scenarios.

Nuclear waste repository siting and locational conflict analysis: A contextual approach

International Nuclear Information System (INIS)

Murauskas, G.T.

1989-01-01

This study develops and evaluates an alternative framework that is based on contextual variables. The premise is that differences in attitudes and perceptions regarding the local siting of nuclear wastes and differences in attitudes regarding siting decision-making procedures are influenced by local political, economic, and cultural variables. This framework articulates the nature of conflict in terms of the incongruence between the use-value individuals ascribe to their present situation and the anticipated exchange-value individuals associate with the local siting of a nuclear waste repository. In order to evaluate this conceptual framework a survey was conducted of residents in four communities representing distinct societal contexts: Richton, Mississippi; Peterborough, New Hampshire; Richland, Washington; and Antigo/Waupaca, Wisconsin. Data analyses indicate substantial differences in economic expectations associated with the local siting of a high-level nuclear waste repository and in perception regarding the impacts such a repository might have on the environment, local agriculture, personal health and safety, and the quality of life

Engineered barrier development for a nuclear waste repository in basalt

International Nuclear Information System (INIS)

Smith, M.J.

1980-05-01

The BWIP Engineered Barrier Program has been developed to provide an integrated approach to the development of site-specific Engineered Barrier assemblages for a repository located in basalt. The goal of this program is to specify engineered and natural barriers which will ensure that nuclear and non-radioactive hazardous materials emplaced in a repository in basalt do not exceed acceptable rates of release to the biosphere. A wide range of analytical and experimental activities related to the basalt repository environment, waste package environment, waste/barrier/rock interactions, and barrier performance assessment provide the basis for selection of systems capable of meeting licensing requirements. Work has concentrated on specifying and testing natural and man-made materials which can be used to plug boreholes in basalt and which can be used as multiple barriers to surround nuclear waste forms and containers. The Engineered Barriers Program is divided into two major activities: multiple barrier studies and borehole plugging. 8 figures, 4 tables

Stabilities of nuclear waste forms and their geochemical interactions in repositories

International Nuclear Information System (INIS)

White, W.B.

1980-01-01

The stabilities of high-level nuclear waste forms in a repository environment are briefly discussed. The advantages and disadvantages of such waste forms as borosilicate glass, supercalcine ceramics, and synthetic minerals are presented in context with the different rock types which have been proposed as possible host rocks for repositories. It is concluded that the growing geochemical evidence favors the use of a silicate rock repository because of the effectiveness of aluminosilicate rocks as chemical barriers for most radionuclides

Nye County, Nevada 1992 nuclear waste repository program: Program overview. Final report

International Nuclear Information System (INIS)

1998-01-01

The purpose of this document is to provide an overview of the Nye County FY92 Nuclear Waste Repository Program (Program). Funds to pay for Program costs will come from the Federal Nuclear Waste Fund, which was established under the Nuclear Waste Policy Act of 1982 (NWPA). In early 1983, the Yucca Mountain was identified as a potentially suitable site for the nation's first geologic repository for spent reactor fuel and high-level radioactive waste. Later that year, the Nye County Board of County Commissioners (Board) established the capability to monitor the Federal effort to implement the NWPA and evaluate the potential impacts of repository-related activities on Nye County. Over the last eight years, the County's program has grown in complexity and cost in order to address DOE's evolving site characterization studies, and prepare for the potential for facility construction and operation. Changes were necessary as well, in response to Congress's redirection of the repository program specified in the amendments, to the NWPA approved in 1987. In early FY 1991, the County formally established a project office to plan and implement its program of work. The Repository Project Office's (RPO) mission and functions are provided in Section 2.0. The RPO organization structure is described in Section 3.0

Optimized application of systems engineering to nuclear waste repository projects

International Nuclear Information System (INIS)

Miskimin, P.A.; Shepard, M.

1986-01-01

The purpose of this presentation is to describe a fully optimized application of systems engineering methods and philosophy to the management of a large nuclear waste repository project. Knowledge gained from actual experience with the use of the systems approach on two repository projects is incorporated in the material presented. The projects are currently evaluating the isolation performance of different geologic settings and are in different phases of maturity. Systems engineering methods were applied by the principal author at the Waste Isolation Pilot Plant (WIPP) in the form of a functional analysis. At the Basalt Waste Isolation Project (BWIP), the authors assisted the intergrating contractor with the development and application of systems engineering methods. Based on this experience and that acquired from other waste management projects, an optimized plan for applying systems engineering techniques was developed. The plan encompasses the following aspects: project organization, developing and defining requirements, assigning work responsibilities, evaluating system performance, quality assurance, controlling changes, enhancing licensability, optimizing project performance, and addressing regulatory issues. This information is presented in the form of a roadmap for the practical application of system engineering principles to a nuclear waste repository project

Performance Assessments of Generic Nuclear Waste Repositories in Shale

Science.gov (United States)

Stein, E. R.; Sevougian, S. D.; Mariner, P. E.; Hammond, G. E.; Frederick, J.

2017-12-01

Simulations of deep geologic disposal of nuclear waste in a generic shale formation showcase Geologic Disposal Safety Assessment (GDSA) Framework, a toolkit for repository performance assessment (PA) whose capabilities include domain discretization (Cubit), multiphysics simulations (PFLOTRAN), uncertainty and sensitivity analysis (Dakota), and visualization (Paraview). GDSA Framework is used to conduct PAs of two generic repositories in shale. The first considers the disposal of 22,000 metric tons heavy metal of commercial spent nuclear fuel. The second considers disposal of defense-related spent nuclear fuel and high level waste. Each PA accounts for the thermal load and radionuclide inventory of applicable waste types, components of the engineered barrier system, and components of the natural barrier system including the host rock shale and underlying and overlying stratigraphic units. Model domains are half-symmetry, gridded with Cubit, and contain between 7 and 22 million grid cells. Grid refinement captures the detail of individual waste packages, emplacement drifts, access drifts, and shafts. Simulations are run in a high performance computing environment on as many as 2048 processes. Equations describing coupled heat and fluid flow and reactive transport are solved with PFLOTRAN, an open-source, massively parallel multiphase flow and reactive transport code. Additional simulated processes include waste package degradation, waste form dissolution, radioactive decay and ingrowth, sorption, solubility, advection, dispersion, and diffusion. Simulations are run to 106 y, and radionuclide concentrations are observed within aquifers at a point approximately 5 km downgradient of the repository. Dakota is used to sample likely ranges of input parameters including waste form and waste package degradation rates and properties of engineered and natural materials to quantify uncertainty in predicted concentrations and sensitivity to input parameters. Sandia National

Microbial corrosion of metallic materials in a deep nuclear-waste repository

Directory of Open Access Journals (Sweden)

Stoulil J.

2016-06-01

Full Text Available The study summarises current knowledge on microbial corrosion in a deep nuclear-waste repository. The first part evaluates the general impact of microbial activity on corrosion mechanisms. Especially, the impact of microbial metabolism on the environment and the impact of biofilms on the surface of structure materials were evaluated. The next part focuses on microbial corrosion in a deep nuclear-waste repository. The study aims to suggest the development of the repository environment and in that respect the viability of bacteria, depending on the probable conditions of the environment, such as humidity of bentonite, pressure in compact bentonite, the impact of ionizing radiation, etc. The last part is aimed at possible techniques for microbial corrosion mechanism monitoring in the conditions of a deep repository. Namely, electrochemical and microscopic techniques were discussed.

Safety analysis of the proposed Canadian geologic nuclear waste repository

International Nuclear Information System (INIS)

Prowse, D.R.

1977-01-01

The Canadian program for development and qualification of a geologic repository for emplacement of high-level and long-lived, alpha-emitting waste from irradiated nuclear fuel has been inititiated and is in its initial development stage. Fieldwork programs to locate candidate sites with suitable geological characteristics have begun. Laboratory studies and development of models for use in safety analysis of the emplaced nuclear waste have been initiated. The immediate objective is to complete a simplified safety analysis of a model geologic repository by mid-1978. This analysis will be progressively updated and will form part of an environmental Assessment Report of a Model Fuel Center which will be issued in mid-1979. The long-term objectives are to develop advanced safety assessment models of a geologic repository which will be available by 1980

Fair rules for siting a high-level nuclear waste repository

International Nuclear Information System (INIS)

Easterling, D.

1992-01-01

Geologic repositories are designed to resolve the ever-growing problem of high-level nuclear waste, but these facilities invite intense local opposition due to the perceived severity of the risks and the possibility of stigma effects. This analysis examines whether the perceived fairness of the siting process affects local residents' support for hosting a repository. In particular, a survey of 1,001 Nevada residents is used to test the hypothesis that an individual's willingness to accept a local repository will increase if he or she is convinced that this is the safest disposal option available. A logistic analysis indicates that beliefs regarding relative suitability have an independent effect on the acceptability of a local repository (i.e., Yucca Mountain). The article then considers the question of how to implement an optimizing strategy for siting facilities, comparing an idealized strategy against the original Nuclear Waste Policy Act (NWPA) of 1982 and the Amendments Act of 1987. Although choosing the safest site seems as if it could enhance public acceptance of the repository program, there is currently little prospect of identifying the best option to the high-level waste problem and, as a results, little chance of gaining the public support that is necessary to promote a successful siting outcome. 81 refs., 1 fig., 5 tabs

Expected brine movement at potential nuclear waste repository salt sites

International Nuclear Information System (INIS)

McCauley, V.S.; Raines, G.E.

1987-08-01

The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m 3 brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs

Extreme scenarios for nuclear waste repositories

Energy Technology Data Exchange (ETDEWEB)

Brown, M J [Harvard Univ., Cambridge, MA (USA). Div. of Applied Sciences; Crouch, E [Harvard Univ., Cambridge, MA (USA). Energy and Environmental Policy Center

1982-09-01

Two extreme scenarios for release of radioactive waste have been constructed. In the first, a volcanic eruption releases 1 km/sup 2/ of an underground nuclear waste repository, while in the second, waste enters the drinking water reservoir of a major city. With pessimistic assumptions, upper bounds on the number of cancers due to radiation are calculated. In the volcano scenario, the effects of the waste are smaller than the effects of natural radioactivity in the volcanic dust if the delay between emplacement and eruption exceeds 2000 yr. The consequences of the waste in drinking water depend on the survival time of the canisters and the rate of leaching of the nuclides from the waste matrix. For a canister life of 400 yr and a leach time of 6300 yr the cancer rate in the affected area would increase by 25%.

Technical conservatism in the design and analysis of a nuclear-waste repository in basalt

International Nuclear Information System (INIS)

Jones, K.A.

1982-01-01

The US Department of Energy's National Waste Terminal Storage Program has adopted a policy of technical conservatism to guide the design and analysis of geologic disposal systems for commercial high-level radioactive waste. Technical conservatism serves as the programmatic philosophy for managing uncertainty in the performance of the disposal system. The implementation of technical conservatism as applied to a nuclear waste repository in basalt is discussed. Preliminary assessments of the performance of the waste package, repository, and site subsystems are compared to key proposed regulatory criteria. The comparison shows that there are substantial safety margins in the predicted performance of the nuclear waste repository in basalt

Symposium on the development of nuclear waste policy: Siting the high-level nuclear waste repository

International Nuclear Information System (INIS)

Pijawka, K.D.; Mushkatel, A.H.

1991-01-01

The Nuclear Waste Policy Act of 1982 (NWPA) attempted to formulate a viable national policy for managing the disposal of high-level nuclear wastes. The NWPA authorized the selection of two repository sites: the first to be constructed in the West and a second site developed in the eastern United States. A detailed process for site selection was outlined in the NWPA. In addition, the NWPA authorized open-quotes the development of a waste transportation system; required the Department of Energy (DOE) to submit a proposal to construct a facility for monitored retrievable storage (MRS) after conducting a study of the need for, and feasibility of such a facility; and required the President to evaluate the use of the repositories ... for the disposal of high-level waste resulting from defense activitiesclose quotes (DOE, 1988, p. 1). A series of provisions granting oversight participation to states and Indian tribes, as well as a compensation package for the ultimate host state were also included. Responsibility for implementing the NWPA was assigned to DOE

Fabrication and closure development of nuclear waste containers for storage at the Yucca Mountain, Nevada repository

International Nuclear Information System (INIS)

Russell, E.W.; Nelson, T.A.; Domian, H.A.; LaCount, D.F.; Robitz, E.S.; Stein, K.O.

1989-04-01

US Congress and the President have determined that the Yucca Mountain site in Nevada is to be characterized to determine its suitability for construction of the first US high-level nuclear waste repository. Work in connection with this site is carried out within the Yucca Mountain Project (YMP). Lawrence Livermore National Laboratory (LLNL) has the responsibility for designing, developing, and projecting the performance of the waste package for the permanent storage of high-level nuclear waste. Babcock ampersand Wilcox (B ampersand W) is involved with the YMP as a subcontractor to LLNL. B ampersand W's role is to recommend and demonstrate a method for fabricating the metallic waste container and a method for performing the final closure of the container after it has been filled with waste. Various fabrication and closure methods are under consideration for the production of containers. This paper presents progress to date in identifying and evaluating the candidate manufacturing processes. 2 refs., 1 fig., 7 tabs

Nuclear Waste Disposal: Alternatives to Yucca Mountain

National Research Council Canada - National Science Library

Holt, Mark

2009-01-01

Congress designated Yucca Mountain, NV, as the nation's sole candidate site for a permanent high-level nuclear waste repository in 1987, following years of controversy over the site-selection process...

Instrument reliability for high-level nuclear-waste-repository applications

International Nuclear Information System (INIS)

Rogue, F.; Binnall, E.P.; Armantrout, G.A.

1983-01-01

Reliable instrumentation will be needed to evaluate the characteristics of proposed high-level nuclear-wasted-repository sites and to monitor the performance of selected sites during the operational period and into repository closure. A study has been done to assess the reliability of instruments used in Department of Energy (DOE) waste repository related experiments and in other similar geological applications. The study included experiences with geotechnical, hydrological, geochemical, environmental, and radiological instrumentation and associated data acquisition equipment. Though this paper includes some findings on the reliability of instruments in each of these categories, the emphasis is on experiences with geotechnical instrumentation in hostile repository-type environments. We review the failure modes, rates, and mechanisms, along with manufacturers modifications and design changes to enhance and improve instrument performance; and include recommendations on areas where further improvements are needed

Selection of Corrosion Resistant Materials for Nuclear Waste Repositories

International Nuclear Information System (INIS)

R.B. Rebak

2006-01-01

Several countries are considering geological repositories to dispose of nuclear waste. The environment of most of the currently considered repositories will be reducing in nature, except for the repository in the US, which is going to be oxidizing. For the reducing repositories, alloys such as carbon steel, stainless steels and titanium are being evaluated. For the repository in the US, some of the most corrosion resistant commercially available alloys are being investigated. This paper presents a summary of the behavior of the different materials under consideration for the repositories and the current understanding of the degradation modes of the proposed alloys in ground water environments from the point of view of general corrosion, localized corrosion and environmentally assisted cracking

Rock mechanics for hard rock nuclear waste repositories

International Nuclear Information System (INIS)

Heuze, F.E.

1981-09-01

The mined geologic burial of high level nuclear waste is now the favored option for disposal. The US National Waste Terminal Storage Program designed to achieve this disposal includes an extensive rock mechanics component related to the design of the wastes repositories. The plan currently considers five candidate rock types. This paper deals with the three hard rocks among them: basalt, granite, and tuff. Their behavior is governed by geological discontinuities. Salt and shale, which exhibit behavior closer to that of a continuum, are not considered here. This paper discusses both the generic rock mechanics R and D, which are required for repository design, as well as examples of projects related to hard rock waste storage. The examples include programs in basalt (Hanford/Washington), in granitic rocks (Climax/Nevada Test Site, Idaho Springs/Colorado, Pinawa/Canada, Oracle/Arizona, and Stripa/Sweden), and in tuff

Extreme scenarios for nuclear waste repositories

Energy Technology Data Exchange (ETDEWEB)

Brown, M J; Crouch, E

1982-09-01

Two extreme scenarios for release of radioactive waste have been constructed. In the first, a volcanic eruption releases 1 km2 of an underground nuclear waste repository, while in the second, waste enters the drinking water reservoir of a major city. With pessimistic assumptions, upper bounds on the number of cancers due to radiation are calculated. In the volcano scenario, the effects of the water are smaller than the effects of natural radioactivity in the volcanic dust if the delay between emplacement and eruption exceeds 2000 yr. The consequences of the waste in drinking water depend on the survival time of the canisters and the rate of leaching of the nuclides from the waste matrix. For a canister life of 400 yr and a leach time of 6300 yr the cancer rate in the affected area would increase by 25%.

Nuclear waste

International Nuclear Information System (INIS)

1992-05-01

The Nuclear Waste Policy Act of 1982, as amended in 1987, directed the Secretary of Energy to, among other things, investigate Yucca Mountain, Nevada, as a potential site for permanently disposing of highly radioactive wastes in an underground repository. In April 1991, the authors testified on Yucca Mountain project expenditures before your Subcommittee. Because of the significance of the authors findings regrading DOE's program management and expenditures, you asked the authors to continue reviewing program expenditures in depth. As agreed with your office, the authors reviewed the expenditures of project funds made available to the Department of Energy's (DOE) Lawrence Livermore National Laboratory, which is the lead project contractor for developing a nuclear waste package that wold be used for disposing of nuclear waste at Yucca Mountain. This report discusses the laboratory's use of nuclear waste funds to support independent research projects and to manage Yucca Mountain project activities. It also discusses the laboratory's project contracting practices

The technical challenge of mechanized excavation for nuclear waste repositories

International Nuclear Information System (INIS)

Smith, A.I.

1991-01-01

This paper presents the historical background of the tunnel boring machine and discusses its integration into the design of a nuclear waste repository. It is essential that the designers of a project utilize the productivity of the system to their advantage. An example would be the construction of a pair of small tunnels instead of a single large diameter access ramp. The pair of tunnels would be more effective in use and less expensive to bore than the single all-purpose tunnel. The designers of an underground nuclear waste repository must recognize the capabilities of the Tunnel Boring Machine system and tailor their design to employ the technological advantages which have been made in recent years

Groundwater-stream-simulation experiments for the evaluation of the safety of proposed nuclear waste repositories

International Nuclear Information System (INIS)

Seitz, M.G.

1981-01-01

A bench-scale experimental design which integrates repository components to simulate a groundwater stream infiltrating a breached repository is described in this paper. An experiment performed with a nuclear waste solid and one rock core is briefly summarized. The nuclear waste solid consists of borosilicate glass containing formulated nuclear waste and is the source of the leached radionuclides. The rock core used is of granite and serves as the adsorption medium for the leached radionuclides

Repository-analog experiments of nuclear waste leaching and migration

International Nuclear Information System (INIS)

Seitz, M.G.

1982-01-01

The potential for radionuclide migration from a breached nuclear-waste repository depends on the leaching and subsequent interaction of the leached radionuclides with materials in the groundwater flow path. An attempt is made to consider all interactions using experiments that integrate repository materials. Results of a repository-analog experiment using borosilicate glass, fissured granite, and flowing water suggest: (1) plutonium was immobile possibly because of its low solubility; (2) caesium migrated down slowly because of sorption; and (3) neptunium remained oxidized even in water of low oxidation potential. By summing the effects of all interactions, not just sorption, the repository-analog experiment produced radionuclide migration that could be expected from a breached repository. (author)

Thermal Analysis of a Nuclear Waste Repository in Argillite Host Rock

Science.gov (United States)

Hadgu, T.; Gomez, S. P.; Matteo, E. N.

2017-12-01

Disposal of high-level nuclear waste in a geological repository requires analysis of heat distribution as a result of decay heat. Such an analysis supports design of repository layout to define repository footprint as well as provide information of importance to overall design. The analysis is also used in the study of potential migration of radionuclides to the accessible environment. In this study, thermal analysis for high-level waste and spent nuclear fuel in a generic repository in argillite host rock is presented. The thermal analysis utilized both semi-analytical and numerical modeling in the near field of a repository. The semi-analytical method looks at heat transport by conduction in the repository and surroundings. The results of the simulation method are temperature histories at selected radial distances from the waste package. A 3-D thermal-hydrologic numerical model was also conducted to study fluid and heat distribution in the near field. The thermal analysis assumed a generic geological repository at 500 m depth. For the semi-analytical method, a backfilled closed repository was assumed with basic design and material properties. For the thermal-hydrologic numerical method, a repository layout with disposal in horizontal boreholes was assumed. The 3-D modeling domain covers a limited portion of the repository footprint to enable a detailed thermal analysis. A highly refined unstructured mesh was used with increased discretization near heat sources and at intersections of different materials. All simulations considered different parameter values for properties of components of the engineered barrier system (i.e. buffer, disturbed rock zone and the host rock), and different surface storage times. Results of the different modeling cases are presented and include temperature and fluid flow profiles in the near field at different simulation times. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and

Nuclear waste repository simulation experiments

International Nuclear Information System (INIS)

Rothfuchs, T.; Wieczorek, K.; Feddersen, H.K.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

1986-12-01

This document is the third joint annual report on the Cooperative German-American 'Brine Migration Tests' that are in progress at the Asse salt mine in the Federal Republic of Germany (FRG). This Government supported mine serves as an underground test facility for research and development (R and D)-work in the field of nuclear waste repository research and simulation experiments. The tests are designed to simulate a nuclear waste repository to measure the effects of heat and gamma radiation on brine migration, salt decrepitation, disassociation of brine, and gases collected. The thermal mechanical behavior of salt, such as room closure, stresses and changes of the properties of salt are measured and compared with predicted behavior. This document covers the following sections: Issues and test objectives: This section presents issues that are investigated by the Brine Migration Test, and the test objectives derived from these issues; test site: This section describes the test site location and geology in the Asse mine; test description: A description of the test configuration, procedures, equipment, and instrumentation is given in this section; actual test chronology: The actual history of the test, in terms of the dates at which major activities occured, is presented in this section. Test results: This section presents the test results observed to data and the planned future work that is needed to complete the test; conclusions and recommendations: This section summarizes the conclusions derived to date regarding the Brine Migration Test. Additional work that would be useful to resolve the issues is discussed. (orig.)

Fabrication and closure development of corrosion resistant containers for Nevada's Yucca Mountain high-level nuclear waste repository

International Nuclear Information System (INIS)

Russell, E.W.; Nelson, T.A.; Domian, H.A.; LaCount, D.F.; Robitz, E.S.; Stein, K.O.

1989-11-01

US Congress and the President have determined that the Yucca Mountain site in Nevada is to be characterized to determine its suitability for construction of the first US high-level nuclear waste repository. Work in connection with this site is carried out within the Yucca Mountain Project (YMP). Lawrence Livermore National Laboratory (LLNL) has the responsibility for designing, developing, and projecting the performance of the waste package for the permanent storage of high-level nuclear waste. Babcock ampersand Wilcox (B ampersand W) is involved with the YMP as a subcontractor to LLNL. B ampersand W's role is to recommend and demonstrate a method for fabricating the metallic waste container and a method for performing the final closure of the container after it has been filled with waste. Various fabrication and closure methods are under consideration for the production of containers. This paper presents progress to date in identifying and evaluating the candidate manufacturing processes. 2 refs., 2 figs., 4 tabs

Selection criteria for container materials at the proposed Yucca Mountain high level nuclear waste repository

International Nuclear Information System (INIS)

Halsey, W.G.

1989-11-01

A geological repository has been proposed for the permanent disposal of the nation's high level nuclear waste at Yucca Mountain in the Nevada desert. The containers for this waste must remain intact for the unprecedented service lifetime of 1000 years. A combination of engineering, regulatory, and licensing requirements complicate the container material selection. In parallel to gathering information regarding the Yucca Mountain service environment and material performance data, a set of selection criteria have been established which compare candidate materials to the performance requirements, and allow a quantitative comparison of candidates. These criteria assign relative weighting to varied topic areas such as mechanical properties, corrosion resistance, fabricability, and cost. Considering the long service life of the waste containers, it is not surprising that the corrosion behavior of the material is a dominant factor. 7 refs

Tunnel Boring Machine for nuclear waste repository research project

International Nuclear Information System (INIS)

Janzon, H.A.

1994-01-01

A description is presented of a Tunnel Boring Machine and its intended use on a research project underway in Sweden for demonstrating and testing methods for rock investigation at a suitable depth for a deep repository for nuclear waste

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the second part of a report of a preliminary study for AECL. It considers the requirements for an underground waste repository for the disposal of wastes produced by the Canadian Nuclear Fuel Program. The following topics are discussed with reference to the repository: 1) geotechnical assessment, 2) hydrogeology and waste containment, 3) thermal loading and 4) rock mechanics. (author)

Nuclear safety requirements for upgrading the National Repository for Radioactive Wastes-Baita Bihor

International Nuclear Information System (INIS)

Vladescu, Gabriela; Necula, Daniela

2000-01-01

The upgrading project of National Repository for Radioactive Wastes-Baita Bihor is based on the integrated concept of nuclear safety. Its ingredients are the following: A. The principles of nuclear safety regarding the management of radioactive wastes and radioprotection; B. Safety objectives for final disposal of low- and intermediate-level radioactive wastes; C. Safety criteria for final disposal of low- and intermediate-level radioactive wastes; D. Assessment of safety criteria fulfillment for final disposal of low- and intermediate-level radioactive wastes. Concerning the nuclear safety in radioactive waste management the following issues are considered: population health protection, preventing transfrontier contamination, future generation radiation protection, national legislation, control of radioactive waste production, interplay between radioactive waste production and management, radioactive waste repository safety. The safety criteria of final disposal of low- and intermediate-level radioactive wastes are discussed by taking into account the geological and hydrogeological configuration, the physico-chemical and geochemical characteristics, the tectonics and seismicity conditions, extreme climatic potential events at the mine location. Concerning the requirements upon the repository, the following aspects are analyzed: the impact on environment, the safety system reliability, the criticality control, the filling composition to prevent radioactive leakage, the repository final sealing, the surveillance. Concerning the radioactive waste, specific criteria taken into account are the radionuclide content, the chemical composition and stability, waste material endurance to heat and radiation. The waste packaging criteria discussed are the mechanical endurance, materials toughness and types as related to deterioration caused by handling, transportation, storing or accidents. Fulfillment of safety criteria is assessed by scenarios analyses and analyses of

Mapping and monitoring nuclear waste repositories with subsurface electrical resistivity arrays

International Nuclear Information System (INIS)

Asch, T.; Morrison, H.F.

1987-01-01

The siting and future integrity of nuclear waste repositories is critically dependent on the local ground water regime. Electrical methods seem particularly promising in mapping and monitoring this regime since the electrical conductivity of rocks depends almost entirely on the fluid saturation, salinity and distribution. The most important recent developments in resistivity include the use of numerical modeling and resistivity mapping using subsurface electrodes. The latter yields far greater accuracy and resolution than can be obtained with surface arrays. To illustrate the power of subsurface-surface arrays the authors studied an idealized two dimensional model of a nuclear repository. Since they are interested in emphasizing the anomaly caused by the repository, or subsequent changes over time in its vicinity, the authors discovered that it is very useful to express the apparent resistivity results as percentage differences from either the background (for surface arrays) or from the apparent resistivities observed at a particular depth of the current source (for subsurface arrays). Percent differencing with respect to data at the repository depth dramatically reduce near-surface and topographic effects that usually confound quantitative interpretation of surface surveys. Thus, dc resistivity appears to have great potential for nuclear waste repository mapping and monitoring

Equity and nuclear waste disposal

International Nuclear Information System (INIS)

Shrader-Frechette, K.

1994-01-01

Following the recommendations of the US National Academy of Sciences and the mandates of the 1987 Nuclear Waste Policy Amendments Act, the US Department of Energy has proposed Yucca Mountain, Nevada as the site of the world's first permanent repository for high-level nuclear waste. The main justification for permanent disposal (as opposed to above-ground storage) is that it guarantees safety by means of waste isolation. This essay argues, however, that considerations of equity (safer for whom?) undercut the safety rationale. The article surveys some prima facie arguments for equity in the distribution of radwaste risks and then evaluates four objections that are based, respectively, on practicality, compensation for risks, scepticism about duties to future generations, and the uranium criterion. The conclusion is that, at least under existing regulations and policies, permanent waste disposal is highly questionable, in part, because it fails to distribute risk equitably or to compensate, in full, for this inequity

The function of packing materials in a high-level nuclear waste repository and some candidate materials: Salt Repository Project

International Nuclear Information System (INIS)

Bunnell, L.R.; Shade, J.W.

1987-03-01

Packing materials should be included in waste package design for a high-level nuclear waste repository in salt. A packing material barrier would increase confidence in the waste package by alleviating possible shortcomings in the present design and prolonging confinement capabilities. Packing materials have been studied for uses in other geologic repositories; appropriately chosen, they would enhance the confinement capabilities of salt repository waste packages in several ways. Benefits of packing materials include retarding or chemically modifying brines to reduce corrosion of the waste package, providing good thermal conductivity between the waste package and host rock, retarding or absorbing radionuclides, and reducing the massiveness of the waste package. These benefits are available at low percentage of total repository cost, if the packing material is properly chosen and used. Several candidate materials are being considered, including oxides, hydroxides, silicates, cement-based mixtures, and clay mixtures. 18 refs

Geochemical modeling of the nuclear-waste repository system. A status report

International Nuclear Information System (INIS)

Deutsch, W.J.

1980-12-01

The primary objective of the geochemical modeling task is to develop an understanding of the waste-repository geochemical system and provide a valuable tool for estimating future states of that system. There currently exists a variety of computer codes which can be used in geochemical modeling studies. Some available codes contain the framework for simulating a natural chemical system and estimating, within limits, the response of that system to environmental changes. By data-base enhancement and code development, this modeling technique can be even more usefully applied to a nuclear-waste repository. In particular, thermodynamic data on elements not presently in the data base but identified as being of particular hazard in the waste-repository system, need to be incorporated into the code to estimate the near-field as well as the far-field reactions during a hypothetical breach. A reaction-path-simulation code, which estimates the products of specific rock/water reactions, has been tested using basalt and ground water. Results show that the mass-transfer capabilities of the code will be useful in chemical-evolution studies and scenario analyses. The purpose of this report is to explain the status of geochemical modeling as it currently applies to the chemical system of a hypothetical nuclear-waste repository in basalt and to present the plan proposed for further developmet and application

Attitudes and opposition in siting a high level nuclear waste repository

International Nuclear Information System (INIS)

Sjoeberg, L.; Viklund, M.; Truedsson, J.

1998-09-01

In Sweden, the Swedish Nuclear Fuel and Waste Management Company (SKB) handles all issues concerning nuclear waste, including the siting process, in which the final outcome is intended to be a repository for high level nuclear waste placed deep down in bedrock. The main objective of the siting process is to find a host community fulfilling two important conditions: the safety demands have been met and agreements with the municipality can be accomplished. Only in such municipalities, so-called feasibility studies will be conducted. After conducting general studies in the whole country, SKB, in October 1992, sent letters with information about the intended feasibility studies to all Swedish municipalities. As a result, feasibility studies are or have been considered - and in some cases also been conducted - in eleven Swedish municipalities up until 1998. These are the municipalities where the attitudes and opposition towards a feasibility study, and possibly a final repository, are studied. The discussion can be divided into three main parts: Management of the siting process; Inherent 'chaotic' processes and/or factors and risk perception. It is argued that two important problems could have been avoided at least partly: The citizens in many municipalities were uncertain of the relationship between a feasibility study and a final repository, and in many municipalities the citizens were afraid that the Government could overrule the municipal veto. Because of these fears, a common argument among the opponents of a feasibility study was: 'to be sure of not receiving a final repository, we say no to a feasibility study'. Some inherent factors, more or less prevalent in the municipalities as well as in society in general, may also partly explain the outcome of the siting process. The municipalities in which the debate has been heated, and where public support has been more difficult to reach, share some common characteristics. Esp. in the municipalities in the north of

Attitudes and opposition in siting a high level nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Sjoeberg, L.; Viklund, M.; Truedsson, J

1998-09-01

In Sweden, the Swedish Nuclear Fuel and Waste Management Company (SKB) handles all issues concerning nuclear waste, including the siting process, in which the final outcome is intended to be a repository for high level nuclear waste placed deep down in bedrock. The main objective of the siting process is to find a host community fulfilling two important conditions: the safety demands have been met and agreements with the municipality can be accomplished. Only in such municipalities, so-called feasibility studies will be conducted. After conducting general studies in the whole country, SKB, in October 1992, sent letters with information about the intended feasibility studies to all Swedish municipalities. As a result, feasibility studies are or have been considered - and in some cases also been conducted - in eleven Swedish municipalities up until 1998. These are the municipalities where the attitudes and opposition towards a feasibility study, and possibly a final repository, are studied. The discussion can be divided into three main parts: Management of the siting process; Inherent `chaotic` processes and/or factors and risk perception. It is argued that two important problems could have been avoided at least partly: The citizens in many municipalities were uncertain of the relationship between a feasibility study and a final repository, and in many municipalities the citizens were afraid that the Government could overrule the municipal veto. Because of these fears, a common argument among the opponents of a feasibility study was: `to be sure of not receiving a final repository, we say no to a feasibility study`. Some inherent factors, more or less prevalent in the municipalities as well as in society in general, may also partly explain the outcome of the siting process. The municipalities in which the debate has been heated, and where public support has been more difficult to reach, share some common characteristics. Esp. in the municipalities in the north of

Identification of key radionuclides in a nuclear waste repository in basalt

International Nuclear Information System (INIS)

Barney, G.S.; Wood, B.J.

1980-05-01

Radionuclides were identified which appear to pose the greatest potential hazard to man during long-term storage of nuclear waste in a repository mined in the Columbia Plateau basalt formation. The criteria used to select key radionuclides were as follows: quantity of radionuclide in stored waste; biological toxicity; leach rate of the wastes into groundwater; and transport rate via groundwater flow. The waste forms were assumed to be either unreprocessed spent fuel or borosilicate glass containing reprocessed high-level waste. The nuclear waste composition was assumed to be that from a light water reactor. Radionuclides were ranked according to quantity, toxicity, and release rate from the repository. These rankings were combined to obtain a single list of key radionuclides. The ten most important radionuclides in order of decreasing hazard are: 99 Tc, 129 I, 237 Np, 226 Ra, 107 Pd, 230 Th, 210 Pb, 126 Sn, 79 Se, and 242 Pu. Safety assessment studies and the design of engineered barriers should concentrate on containment of radionuclides in this list

Double Diffusive Natural Convection in a Nuclear Waste Repository

International Nuclear Information System (INIS)

Y. Hao; J. Nitao; T.A. Buscheck; Y. Sun

2006-01-01

In this study, we conduct a two-dimensional numerical analysis of double diffusive natural convection in an emplacement drift for a nuclear waste repository. In-drift heat and moisture transport is driven by combined thermal- and compositional-induced buoyancy forces. Numerical results demonstrate buoyancy-driven convective flow patterns and configurations during both repository heat-up and cool-down phases. It is also shown that boundary conditions, particularly on the drip-shield surface, have strong impacts on the in-drift convective flow and transport

Workshop on Potentially Disruptive Phenomena for Nuclear Waste Repositories, July 27-28, 1977

International Nuclear Information System (INIS)

Jacobson, J.J.

1977-01-01

The workshop on Potentially Disruptive Phenomena for Nuclear Waste Repositories brought together experts in the geosciences to identify and evaluate potentially disruptive events and processes and to contribute ideas on how to extrapolate data from the past into the next one million years. The analysis is to be used to model a repository in geologic media for long-term safety assessments of nuclear waste storage. The workshop included invited presentations on the following items: an overview of the Waste Isolation Safety Assessment Program (WISAP), simulation techniques, subjective probabilities and methodology of obtaining data, similar modeling efforts at Lawrence Livermore and Sandia Laboratories, and geologic processes or events

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the first part of a report of a preliminary study for Atomic Energy of Canada Limited. It considers the requirements for an underground waste repository for the disposal of wastes produced by the Canadian Nuclear Fuel Program. The following topics are discussed with reference to the repository: 1) underground layout, 2) cost estimates, 3) waste handling, 4) retrievability, decommissioning, sealing and monitoring, and 5) research and design engineering requirements. (author)

Preliminary drift design analyses for nuclear waste repository in tuff

International Nuclear Information System (INIS)

Hardy, M.P.; Brechtel, C.E.; Goodrich, R.R.; Bauer, S.J.

1990-01-01

The Yucca Mountain Project (YMP) is examining the feasibility of siting a repository for high-level nuclear waste at Yucca Mountain, on and adjacent to the Nevada Test Site (NTS). The proposed repository will be excavated in the Topopah Spring Member, which is a moderately fractured, unsaturated, welded tuff. Excavation stability will be required during construction, waste emplacement, retrieval (if required), and closure to ensure worker safety. The subsurface excavations will be subject to stress changes resulting from thermal expansion of the rock mass and seismic events associated with regional tectonic activity and underground nuclear explosions (UNEs). Analyses of drift stability are required to assess the acceptable waste emplacement density, to design the drift shapes and ground support systems, and to establish schedules and cost of construction. This paper outlines the proposed methodology to assess drift stability and then focuses on an example of its application to the YMP repository drifts based on preliminary site data. Because site characterization activities have not begun, the database currently lacks the extensive site-specific field and laboratory data needed to form conclusions as to the final ground support requirements. This drift design methodology will be applied and refined as more site-specific data are generated and as analytical techniques and methodologies are verified during the site characterization process

Mathematical modelling of heat production in deep geological repository of high-level nuclear waste

International Nuclear Information System (INIS)

Kovanda, O.

2017-01-01

Waste produced by nuclear industry requires special handling. Currently, there is a research taking place, focused at possibilities of nuclear waste storage in deep geological repositories, hosted in stable geological environment. The high-level nuclear waste produces significant amount of heat for a long time, which can affect either environment outside of or within the repository in a negative way. Therefore to reduce risks, it is desirable to know the principles of such heat production, which can be achieved using mathematical modeling. This thesis comes up with a general model of heat production-time dependency, dependable on initial composition of the waste. To be able to model real situations, output of this thesis needs to be utilized in an IT solution. (authors)

Nuclear Waste Policy Act of 1982; proposed general guidelines for recommendation of sites for nuclear waste repositories

International Nuclear Information System (INIS)

Anon.

1983-01-01

In accordance with the requirements of the Nuclear Waste Policy Act of 1982 (Pub. L. 97-425), hereinafter referred to as the Act, the Department of Energy is proposing general guidelines for the recommendation of sites for repositories for disposal of high-level radioactive waste and spent nuclear fuel in geologic formations. These guidelines are based on the criteria that the Department has used in its National Waste Terminal Storage program, the criteria proposed by the Nuclear Regulatory Commission (NRC), and the environmental standards proposed by the Environmental Protection Agency. These guidelines establish the performance requirements for a geologic repository system, specify how the Department will implement its site-selection program, and define the technical qualifications that candidate sites must meet in the various steps of the site-selection process mandated by the Act. After considering comments from the public; consulting with the Council on Environmental Quality, the Administrator of the Environmental Protection Agency, the Director of the Geological Survey, and interested Governors; and obtaining NRC concurrence, the Department will issue these guidelines in final form as a new Part 960 to Title 10 of the Code of Federal Regulations (10 CFR Part 960)

The Finnish Experience with the Construction of Onkalo. Licensing of a repository for nuclear waste in Finland

International Nuclear Information System (INIS)

Avolahti, Jaana

2014-01-01

Pursuant to the Nuclear Energy Act (990/1987), a license holder whose operations result, or have resulted, in the generation of nuclear waste must perform all measures included in the management of nuclear waste and preparation thereof and bear all the costs of nuclear waste management. Under law, spent nuclear fuel is regarded as nuclear waste. According to the amendment made to the Nuclear Energy Act in 1994, nuclear waste generated in Finland must be handled, stored and permanently disposed of in Finland. Nuclear waste generated elsewhere may not be handled, stored and permanently disposed of in Finland. The Finnish nuclear legislation defines spent fuel as nuclear waste and requires that it has to be disposed of in the Finnish bedrock. Over 30 years of systematic R and D has been carried out to develop the repository concept, site selection, technologies, safety assessment and the regulatory approach. Activities are based on the Finnish Government's long term strategies since 1983. The stepwise development and future plans for disposal are presented in Table 1. The licensing procedure for a disposal facility has several steps that are similar to all nuclear facilities in Finland and are defined in Nuclear Energy Act (990/1987) and Decree (161/1988). These licensing steps are: - Decision in Principle (DiP); - Construction License; - Operational License. An Environmental Impact Assessment (EIA) shall be conducted prior to the first authorization step of a major nuclear waste facility. The EIA procedure for the final disposal of spent nuclear fuel from three units of the Olkiluoto nuclear power plant and two units of the Loviisa nuclear power plant was carried out in 1998-1999 and extended to one more unit at Olkiluoto in 2008- 2009. Pursuant to the Nuclear Energy Act, before making the DiP the Government shall ascertain whether the municipality planned as the location of the nuclear facility is in favour of the facility, and ensure that no facts indicating a

Characterization of Discharge Areas of Radionuclides Originating From Nuclear Waste Repositories

Science.gov (United States)

Marklund, L.; Xu, S.; Worman, A.

2009-05-01

If leakages in nuclear waste repositories located in crystalline bedrock arise, radionuclides will reach the biosphere and cause a risk of radiological impact. The extent of the radiological impact depends on in which landscape elements the radionuclides emerge. In this study, we investigate if there are certain landscape elements that generally will act as discharge areas for radionuclides leaking from subsurface deposits. We also characterize the typical properties that distinguish these areas from others. In humid regions, landscape topography is the most important driving force for groundwater flow. Because groundwater is the main transporting agent for migrating radionuclides, the topography will determine the flowpaths of leaking radionuclides. How topography and heterogeneities in the subsurface affect the discharge distribution of the radionuclides is therefore an important scope of this study. To address these issues, we developed a 3-D transport model. Our analyses are based on site-specific data from two different areas in Sweden, Forsmark, Uppland, and Oskarshamn, Småland. The Swedish Nuclear Waste Management Company (SKB) has selected these two areas as candidate areas for a deep repository of nuclear waste and the areas are currently subject to site investigations. Our results suggest that there are hot-spots in the landscape i.e. areas with high probability of receiving large amounts of radionuclides from a leaking repository of nuclear waste. The hot-spots concentrate in the sea, streams, lakes and wetlands. All these elements are found at lower elevations in the landscape. This pattern is mostly determined by the landscape topography and the locations of fracture zones. There is a relationship between fracture zones and topography, and therefore the importance of the topography for the discharge area distribution is not contradicted by the heterogeneity in the bedrock. The varieties of landscape elements which have potential for receiving

Environmental program overview for a high-level radioactive waste repository at Yucca Mountain

International Nuclear Information System (INIS)

1988-12-01

The United States plans to begin operating the first repository for the permanent disposal of high-level nuclear waste early in the next century. In February 1983, the US Department of Energy (DOE) identified Yucca Mountain, in Nevada, as one of nine potentially acceptable sites for a repository. To determine its suitability, the DOE evaluated the Yucca Mountain site, along with eight other potentially acceptable sites, in accordance with the DOE's General Guidelines for the Recommendation of Sites for the Nuclear Waste Repositories. The purpose of the Environmental Program Overview (EPO) for the Yucca Mountain site is to provide an overview of the overall, comprehensive approach being used to satisfy the environmental requirements applicable to sitting a repository at Yucca Mountain. The EPO states how the DOE will address the following environmental areas: aesthetics, air quality, cultural resources (archaeological and Native American components), noise, radiological studies, soils, terrestrial ecosystems, and water resources. This EPO describes the environmental program being developed for the sitting of a repository at Yucca Mountain. 1 fig., 3 tabs

Materials Degradation Issues in the U.S. High-Level Nuclear Waste Repository

Energy Technology Data Exchange (ETDEWEB)

K.G. Mon; F. Hua

2005-04-12

This paper reviews the state-of-the-art understanding of the degradation processes by the Yucca Mountain Project (YMP) with focus on interaction between the in-drift environmental conditions and long-term materials degradation of waste packages and drip shields within the repository system during the first 10,000-years after repository closure. This paper provides an overview of the degradation of the waste packages and drip shields in the repository after permanent closure of the facility. The degradation modes discussed in this paper include aging and phase instability, dry oxidation, general and localized corrosion, stress corrosion cracking, and hydrogen induced cracking of Alloy 22 and titanium alloys. The effects of microbial activity and radiation on the degradation of Alloy 22 and titanium alloys are also discussed. Further, for titanium alloys, the effects of fluorides, bromides, and galvanic coupling to less noble metals are considered. It is concluded that the materials and design adopted will provide sufficient safety margins for at least 10,000-years after repository closure.

Materials Degradation Issues in the U.S. High-Level Nuclear Waste Repository

International Nuclear Information System (INIS)

Mon, K.G.; Hua, F.

2005-01-01

This paper reviews the state-of-the-art understanding of the degradation processes by the Yucca Mountain Project (YMP) with focus on interaction between the in-drift environmental conditions and long-term materials degradation of waste packages and drip shields within the repository system during the first 10,000-years after repository closure. This paper provides an overview of the degradation of the waste packages and drip shields in the repository after permanent closure of the facility. The degradation modes discussed in this paper include aging and phase instability, dry oxidation, general and localized corrosion, stress corrosion cracking, and hydrogen induced cracking of Alloy 22 and titanium alloys. The effects of microbial activity and radiation on the degradation of Alloy 22 and titanium alloys are also discussed. Further, for titanium alloys, the effects of fluorides, bromides, and galvanic coupling to less noble metals are considered. It is concluded that the materials and design adopted will provide sufficient safety margins for at least 10,000-years after repository closure

An analysis of repository waste-handling operations

International Nuclear Information System (INIS)

Dennis, A.W.

1990-09-01

This report has been prepared to document the operational analysis of waste-handling facilities at a geologic repository for high-level nuclear waste. The site currently under investigation for the geologic repository is located at Yucca Mountain, Nye County, Nevada. The repository waste-handling operations have been identified and analyzed for the year 2011, a steady-state year during which the repository receives spent nuclear fuel containing the equivalent of 3000 metric tons of uranium (MTU) and defense high-level waste containing the equivalent of 400 MTU. As a result of this analysis, it has been determined that the waste-handling facilities are adequate to receive, prepare, store, and emplace the projected quantity of waste on an annual basis. In addition, several areas have been identified where additional work is required. The recommendations for future work have been divided into three categories: items that affect the total waste management system, operations within the repository boundary, and the methodology used to perform operational analyses for repository designs. 7 refs., 48 figs., 11 tabs

Congressional-executive interaction and the nuclear waste repository site selection process

International Nuclear Information System (INIS)

Thurber, J.A.; Evanson, T.C.

1993-01-01

The Nuclear Waste Policy Act of 1982 (NWPA) (P.L. 97-425) and the Nuclear Waste Policy Amendments Act of 1987 (NWPAA) (Title V of P.L. 100-203) provide the framework for the DOE Office of Civilian Radioactive Waste Management (OCRWM) to find a permanent means for disposing of high-level nuclear waste in the US. The focus of this study is the congressional decision-making process associated with passage of the Nuclear Waste Policy Amendments Act of 1987. The passage of NWPAA was a direct result of the failure of the policy adopted in the Nuclear Waste Policy Act of 1982. This study analyzes the nature of congressional nuclear waste policy-making through the lens of subsystems theory. The data analysis is primarily based on confidential interviews with over fifty key actors in the nuclear waste policy subsystem as well as an analysis of primary source documents

Kriging analysis for a candidate nuclear waste repository

International Nuclear Information System (INIS)

Devary, J.L.

1983-08-01

An important aspect of ensuring the safety of a geologic nuclear waste repository involves the study of ground-water flow at the proposed site. Geohydrologic site characterization involves the evaluation of potentiometric (head) data from confined aquifers. Geostatistical techniques (kriging) are applied to head measurements from the Permian System, a geologic formation being considered by the Department of Energy for nuclear waste disposal. The kriging analysis investigates the adequacy of the data base, provides methods for data screening, and determines optimal locations for additional data collection. This presentation illustrates the development of a generalized covariance and the production of potentiometric contour maps and error maps. The advantages of kriging over traditional least squares regression analysis are also discussed. 17 references

The application of nuclear geophysics method to evaluate the geological environment of nuclear waste repository

International Nuclear Information System (INIS)

Fang, Fang; Xiaoqin, Wang; Kuanliang, Li; Xinsheng, Hou; Jingliang, Zhu; Binxin, Hu

2002-01-01

'Cleanly land should be given back ground.' This is a task while nuclear engineering have to be retired. We applied the nuclear geophysics methods and combined with geology, hydrology, geochemistry, and other methods, to evaluate the environment of nuclear waste repository. It is the important work to renovate environment and prepare technology before ex-service of the nuclear engineering

Natural scientific strategy for nuclear wastes: Philosophy of Dr. Rodney C. Ewing at Stanford

Energy Technology Data Exchange (ETDEWEB)

Woo, T. H. [The Cyber University of Korea, Seoul (Korea, Republic of)

2016-10-15

In the geological study, the naturally adapted region was discovered in Oklo, a central African area of Gabon seen in Fig. 1. Currently, this naturally operated nuclear fission site has been stabilized where the artificial shielding structure was not equipped. So, it has been studied to be an exemplified high-level nuclear waste repository. This could give a lesson that one should make the nuclear repository construction. The simplified configuration of the Oklo natural nuclear reactor site is described. The important mentions of Dr. Ewing reflected his philosophy in geological repository and there is a biography. It is necessary to understand the very big difference between human’s cognitive timescale and geological timescale where it could be nearly impossible to construct the long-term or even permanent nuclear waste repository. It is important to understand the opposite opinions of the nuclear waste repository. The government made the milestone of the South Korean repository policy in which the final repository completion was decided as 2053, about 40 years later. Until the time, there is enough time to rethink for the long-term waste repository. It is certain the policy-maker of this nuclear waste policy will be out of the nuclear community before 2053. This means the politician will not take any responsibility of the result of this policy.

Natural scientific strategy for nuclear wastes: Philosophy of Dr. Rodney C. Ewing at Stanford

International Nuclear Information System (INIS)

Woo, T. H.

2016-01-01

In the geological study, the naturally adapted region was discovered in Oklo, a central African area of Gabon seen in Fig. 1. Currently, this naturally operated nuclear fission site has been stabilized where the artificial shielding structure was not equipped. So, it has been studied to be an exemplified high-level nuclear waste repository. This could give a lesson that one should make the nuclear repository construction. The simplified configuration of the Oklo natural nuclear reactor site is described. The important mentions of Dr. Ewing reflected his philosophy in geological repository and there is a biography. It is necessary to understand the very big difference between human’s cognitive timescale and geological timescale where it could be nearly impossible to construct the long-term or even permanent nuclear waste repository. It is important to understand the opposite opinions of the nuclear waste repository. The government made the milestone of the South Korean repository policy in which the final repository completion was decided as 2053, about 40 years later. Until the time, there is enough time to rethink for the long-term waste repository. It is certain the policy-maker of this nuclear waste policy will be out of the nuclear community before 2053. This means the politician will not take any responsibility of the result of this policy

Should high-level nuclear waste be disposed of at geographically dispersed sites?

International Nuclear Information System (INIS)

Bassett, G.W. Jr.

1992-01-01

Consideration of the technical feasibility of Yucca Mountain in Nevada as the site for a high-level nuclear waste repository has led to an intense debate regarding the economic, social, and political impacts of the repository. Impediments to the siting process mean that the nuclear waste problem is being resolved by adhering to the status quo, in which nuclear waste is stored at scattered sites near major population centers. To assess the merits of alternative siting strategies--including both the permanent repository and the status quo- we consider the variables that would be included in a model designed to select (1) the optimal number of disposal facilities, (2) the types of facilities (e.g., permanent repository or monitored retrievable facility), and (3) the geographic location of storage sites. The objective function in the model is an all-inclusive measure of social cost. The intent of the exercise is not to demonstrate the superiority of any single disposal strategy; uncertainties preclude a conclusive proof of optimality for any of the disposal options. Instead, we want to assess the sensitivity of a variety of proposed solutions to variations in the physical, economic, political, and social variables that influence a siting strategy

Geoscience data base handbook for modeling a nuclear waste repository. Volume 1

International Nuclear Information System (INIS)

Isherwood, D.

1979-12-01

This handbook contains reference information on parameters that should be considered in analyzing or modeling a proposed nuclear waste repository site. Only those parameters and values that best represent the natural environment are included. Rare extremes are avoided. Where laboratory and field data are inadequate, theoretical treatments and informed engineering judgements are presented. Volume 1 contains a data base on salt as a repository medium. Chapters on the geology of bedded and dome salt, the geomechanics of salt, hydrology, geochemistry, natural and man-made features, and seismology provide compiled data and related information useful for studying a proposed repository in salt. These and other data will be needed to derive generic deep geologic modeling parameters and will also serve as background for the verification of source data that may be presented in licensing applications for nuclear waste repositories. Volume 2 is the result of a scoping study for a data base on the geology, geomechanics, and hydrology of shale, granite, and basalt as alternative repository media. Except for the geomechanics of shale, most of the sections contain relatively complete compilations of the available data, as well as discussions of the properties that are unique to each rock type

Rock mass modification around a nuclear waste repository in welded tuff

International Nuclear Information System (INIS)

Mack, M.G.; Brandshaug, T.; Brady, B.H.

1989-08-01

This report presents the results of numerical analyses to estimate the extent of rock mass modification resulting from the presence of a High Level Waste (HLW) repository. Changes in rock mass considered are stresses and joint deformations resulting from disposal room excavation and thermal efffects induced by the heat generated by nuclear waste. rock properties and site conditions are taken from the Site Characterization Plan Conceptual Design Report for the potential repository site at Yucca Mountain, Nevada. Analyses were conducted using boundary element and distinct element methods. Room-scale models and repository-scale models were investigated for up to 500 years after waste emplacement. Results of room-scale analyses based on the thermoelastic boundary element model indicate that a zone of modified rock develops around the disposal rooms for both vertical and horizontal waste emplacement. This zone is estimated to extend a distance of roughly two room diameters from the room surface. Results from the repository-scale model, which are based on the thermoelastic boundary element model and the distinct element model, indicate a zone with modified rock mass properties starting approximately 100 m above and below the repository, with a thickness of approximately 200 m above and 150 m below the repository. Slip-prone subhorizontal features are shown to have a substantial effect on rock mass response. The estimates of rock mass modification reflect uncertainties and simplifying assumptions in the models. 32 refs., 57 figs., 1 tab

Nuclear waste management: a challenge to Federalism

International Nuclear Information System (INIS)

Lucas, P.

1979-01-01

The controversy over state/Federal authority over waste disposal has already had a significant effect regardless of the choice Congress ultimately makes between an informal deference to state will and a statutory authorization of state control over Federal repositories. The highly emotional issue of local disposal of nuclear waste and the assertions of state control over waste disposal have made the nation and the Federal bureaucracy more aware of the status of the waste management program. State resistance to Federal siting efforts and the passage of state waste disposal legislation has compelled the Federal government to provide the states with a larger role in waste management. State power to exclude Federal repositories would give states additional political leverage. Ideally, public attention and effective state veto power will contribute to a more successful program, without impeding progress toward the immediate goal of siting and developing permanent repositories

Some concepts of model uncertainty for performance assessments of nuclear waste repositories

International Nuclear Information System (INIS)

Eisenberg, N.A.; Sagar, B.; Wittmeyer, G.W.

1994-01-01

Models of the performance of nuclear waste repositories will be central to making regulatory decisions regarding the safety of such facilities. The conceptual model of repository performance is represented by mathematical relationships, which are usually implemented as one or more computer codes. A geologic system may allow many conceptual models, which are consistent with the observations. These conceptual models may or may not have the same mathematical representation. Experiences in modeling the performance of a waste repository representation. Experiences in modeling the performance of a waste repository (which is, in part, a geologic system), show that this non-uniqueness of conceptual models is a significant source of model uncertainty. At the same time, each conceptual model has its own set of parameters and usually, it is not be possible to completely separate model uncertainty from parameter uncertainty for the repository system. Issues related to the origin of model uncertainty, its relation to parameter uncertainty, and its incorporation in safety assessments are discussed from a broad regulatory perspective. An extended example in which these issues are explored numerically is also provided

Learning from nuclear waste repository design: the ground-control plan

International Nuclear Information System (INIS)

Schmidt, B.

1988-01-01

At present, under a U.S. Department of Energy program, three repositories for commercial spent fuel-in salt, tuff and basalt-are in the phase of site characterization and conceptual design, and one pilot project for defense waste in salt is under development. Because of strict quality assurance requirements throughout design and construction, and the need to predict and ascertain in advance the satisfactory performance of the underground openings, underground openings in the unusual circumstances of the repository environment have been analysed. This will lead to an improved understanding of rock behavior and improved methods of underground analysis and design. A formalized ground control plan was developed, the principles of which may be applied to other types of projects. This paper summarizes the status of underground design and construction for nuclear waste repositories and presents some details of the ground control plan and its individual elements. (author)

Natural geochemical analogues of the near field of high-level nuclear waste repositories

International Nuclear Information System (INIS)

Apps, J.A.

1995-01-01

United States practice has been to design high-level nuclear waste (HLW) geological repositories with waste densities sufficiently high that repository temperatures surrounding the waste will exceed 100 degrees C and could reach 250 degrees C. Basalt and devitrified vitroclastic tuff are among the host rocks considered for waste emplacement. Near-field repository thermal behavior and chemical alteration in such rocks is expected to be similar to that observed in many geothermal systems. Therefore, the predictive modeling required for performance assessment studies of the near field could be validated and calibrated using geothermal systems as natural analogues. Examples are given which demonstrate the need for refinement of the thermodynamic databases used in geochemical modeling of near-field natural analogues and the extent to which present models can predict conditions in geothermal fields

Can nuclear waste be stored safely at Yucca mountain?

International Nuclear Information System (INIS)

Whipple, C.G.

1996-01-01

In 1987 the federal government narrowed to one its long-term options for disposing of nuclear waste: storing it permanently in a series of caverns excavated out of the rock deep below Yucca mountain in southern Nevada. Whether it makes sense at this time to dispose permanently of spent fuel and radioactive waste in a deep geologic repository is hotly disputed. But the Nuclear Waste Policy Act amendements of 1987 decree that waste be consolidated in Yucca Mountain if the mountain is found suitable. Meanwhile the spent fuel continues to pile up across the country, and 1998 looms, adding urgency to the question: What can science tell us about the ability of the mountain to store nuclear waste safely? This paper discusses this issue and describes how studies of the mountain's history and geology can contribute useful insights but not unequivocal conclusions

Siting the nation's first high-level nuclear waste repository: Social impacts for Utah

International Nuclear Information System (INIS)

Olshansky, S.J.

1986-01-01

The siting of a high-level nuclear waste repository in the United States has been an issue of great controversy, particulary for the states under consideration. In addition to concerns expressed about the geological stability of the proposed sites, numerous social issues have been raised by the general public--most of which have been addressed by the draft environmental impact statements. Among the social impacts raised by the Department of Engery and the general public, those receiving the greatest attention were the potential influence of the repository on local economics, tourism, and the health status of the local residents. The major issues of interest in the present study include 1) the effects of respondent knowledge of nuclear waste disposal issues on opinions of health effects and tourism, particularly as they are affected by visitation patterns, and 2) the effects of occupation and education (in particular) on knowledge of nuclear waste disposal issues and opinions on technical and non-technical aspects of siting the repository. Preliminary results indicate that only about 40 percent of the respondents have visited the national parks in southeastern Utah, but over 70 percent feel they are informed about the issues associated with siting the repository. Over 60 percent of the respondents were very concerned about the possible negative effect the repository could have on jobs, tourism, health effects, and environmental quality. Cross-tabulations indicate that the respondents self rating on knowledge of nuclear disposal issues has a statistically significant influence on responses to socioeconomic issues, yet the same self rating scale is significantly influenced by the frequency with which respondents have visited the national parks in southeastern Utah

International perspective on repositories for low level waste

International Nuclear Information System (INIS)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva

2011-12-01

Nuclear energy production gives rise to different types of radioactive waste. The use of nuclear isotopes within the research, industry and medical sectors also generates radioactive waste. To protect man and the environment from radiation the waste is isolated and contained by deposition in repositories. These repositories may have various designs regarding location, barriers etc depending on the potential danger of the waste. In Sweden, low- and intermediate level waste (LILW) is disposed of in the SFR repository in Forsmark. The repository is located 60 metres down into the bedrock under the bottom of the sea and covered by 6 metres of water. It is planned to extend SFR to accommodate decommissioning waste from the dismantling of the Swedish nuclear power facilities and also for the additional operation waste caused by the planned prolonged operation time. When planning the extension consultations will be carried out with the host municipality, authorities, organisations and general public. In planning the extension, SKB has performed a worldwide compilation of how other countries have, or plan to, handle the final disposal of similar wastes. The aim of this report is to give a brief description of LILW repositories worldwide; including general brief descriptions of many facilities, descriptions of the waste and the barriers as well as safety assessments for a few chosen repositories which represent different designs. The latter is performed, where possible, to compare certain features against the Swedish SFR. To provide a background and context to this study, international organisations and conventions are also presented along with internationally accepted principles regarding the management of radioactive waste. Similar to SFR, suitable locations for the repositories have, in many countries, been found at sites that already have, or used to have nuclear activities, such as reactor sites. Abandoned and disused mines, such as the salt mines in Germany, also

International perspective on repositories for low level waste

Energy Technology Data Exchange (ETDEWEB)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva (SKB International AB (Sweden))

2011-12-15

Nuclear energy production gives rise to different types of radioactive waste. The use of nuclear isotopes within the research, industry and medical sectors also generates radioactive waste. To protect man and the environment from radiation the waste is isolated and contained by deposition in repositories. These repositories may have various designs regarding location, barriers etc depending on the potential danger of the waste. In Sweden, low- and intermediate level waste (LILW) is disposed of in the SFR repository in Forsmark. The repository is located 60 metres down into the bedrock under the bottom of the sea and covered by 6 metres of water. It is planned to extend SFR to accommodate decommissioning waste from the dismantling of the Swedish nuclear power facilities and also for the additional operation waste caused by the planned prolonged operation time. When planning the extension consultations will be carried out with the host municipality, authorities, organisations and general public. In planning the extension, SKB has performed a worldwide compilation of how other countries have, or plan to, handle the final disposal of similar wastes. The aim of this report is to give a brief description of LILW repositories worldwide; including general brief descriptions of many facilities, descriptions of the waste and the barriers as well as safety assessments for a few chosen repositories which represent different designs. The latter is performed, where possible, to compare certain features against the Swedish SFR. To provide a background and context to this study, international organisations and conventions are also presented along with internationally accepted principles regarding the management of radioactive waste. Similar to SFR, suitable locations for the repositories have, in many countries, been found at sites that already have, or used to have nuclear activities, such as reactor sites. Abandoned and disused mines, such as the salt mines in Germany, also

Nuclear waste package fabricated from concrete

International Nuclear Information System (INIS)

Pfeiffer, P.A.; Kennedy, J.M.

1987-03-01

After the United States enacted the Nuclear Waste Policy Act in 1983, the Department of Energy must design, site, build and operate permanent geologic repositories for high-level nuclear waste. The Department of Energy has recently selected three sites, one being the Hanford Site in the state of Washington. At this particular site, the repository will be located in basalt at a depth of approximately 3000 feet deep. The main concern of this site, is contamination of the groundwater by release of radionuclides from the waste package. The waste package basically has three components: the containment barrier (metal or concrete container, in this study concrete will be considered), the waste form, and other materials (such as packing material, emplacement hole liners, etc.). The containment barriers are the primary waste container structural materials and are intended to provide containment of the nuclear waste up to a thousand years after emplacement. After the containment barriers are breached by groundwater, the packing material (expanding sodium bentonite clay) is expected to provide the primary control of release of radionuclide into the immediate repository environment. The loading conditions on the concrete container (from emplacement to approximately 1000 years), will be twofold; (1) internal heat of the high-level waste which could be up to 400 0 C; (2) external hydrostatic pressure up to 1300 psi after the seepage of groundwater has occurred in the emplacement tunnel. A suggested container is a hollow plain concrete cylinder with both ends capped. 7 refs

Nuclear waste: How the issue falls out

International Nuclear Information System (INIS)

Garner, W.L.

1995-01-01

Unless Congress takes some action, utilities will be forced to provide onsite storage of spent fuel from civilian nuclera reactors much longer than they ever imagined. Congress's failure to authorize the Department of Energy (DOE) to begin planning a centralized, interim storage facility and, equally important, to accelerate development of a permanent repository, means that spent nuclear fuel will remain in limbo at 73 reactor sites in 34 states. Today's 30,000 metric tons of spent fuel from civilian nuclear plants will grow to 85,000 metric tons by 2033, according to DOE. The agency also must find a home for a future 70,000 tons of defense waste. There is a growing sense of urgency in Congress this year that something must be done about the nation's nuclear waste problem. By 1998, 26 civilian nuclear units will have exhausted their storage capacity. By 2010 - the earliest DOE says it could open a permanent repository at Yucca Mountain in Nevada, provided the site proves feasible - 80 nuclear units will be out of storage space. At least half a dozen bills have been introduced so far in the 104th Congress, by both propoents and opponents of nuclear power. Recent events in Washington suggest this will be a hard-fought battle

Management of radioactive waste at Novi Han Repository

International Nuclear Information System (INIS)

Stefanova, I.G.; Mateeva, M.D.; Milanov, M.V.

2002-01-01

The Novi Han Repository is the only existing repository in Bulgaria for the disposal of radioactive waste from nuclear applications in industry, medicine and research. The repository was constructed in the early sixties according to the existing requirements. It was operated by the Institute for Nuclear Research and Nuclear Energy for more than thirty years without any accident or release of radioactivity to the environment, but without any investment for upgrading. As a consequence, the Bulgarian Nuclear Safety Authority temporarily stopped the operation of the repository in 1994. The measures for upgrading the Novi Han Repository, supported by the IAEA under TC Project BUL/4/005 'Increasing Safety of Novi Han Repository', are presented in this paper. They comprise: assessment of radionuclide inventory and future waste arisings, characterisation of disposal vaults, characterisation of the site, safety assessment, upgrading of the monitoring system, option study for the selection of treatment and conditioning processes and the development of a conceptual design for low and intermediate level waste processing and storage facility, immediate measures for improvement of the existing disposal vaults and infrastructure, construction of above-ground temporary storage structures, and resuming the operation of the Novi Han Repository. The necessary activities for re-licensing of the Novi Han Repository, construction of a waste processing and storage facility and a disposal facility for spent sealed sources are discussed. (author)

Retrievability of high-level nuclear waste from geologic repositories - Regulatory and rock mechanics/design considerations

International Nuclear Information System (INIS)

Tanious, N.S.; Nataraja, M.S.; Daemen, J.J.K.

1987-01-01

Retrievability of nuclear waste from high-level geologic repositories is one of the performance objectives identified in 10CFR60 (Code of Federal Regulations, 1985). 10CFR60.111 states that the geologic repository operations area shall be designed to preserve the option of waste retrieval. In designing the repository operations area, rock mechanics considerations play a major role especially in evaluating the feasibility of retrieval operations. This paper discusses generic considerations affecting retrievability as they relate to repository design, construction, and operation, with emphasis on regulatory and rock mechanics aspects

Public opposition to the siting of the high-level nuclear waste repository: The importance of trust

International Nuclear Information System (INIS)

Pijawka, K.D.; Mushkatel, A.H.

1991-01-01

This paper examines several dimensions of public opposition to the proposed siting of the high-level nuclear waste repository at Yucca Mountain. In order to provide a context for the public's views of the repository in metropolitan Clark County, both governmental studies of the repository siting process are analyzed, as well as elements of the Nuclear Waste Policy Act. This analysis suggests that one potentially key component of the public's opposition to the siting, as well as their perceptions of risk of the facility, may be the result of a lack of trust in the Department of Energy. Empirical analysis of survey data collected in Nevada in 1988 confirms the strong relationship between political trust and repository risk perceptions

Siting of repositories for high level nuclear waste geological and institutional issues

International Nuclear Information System (INIS)

Ahagen, H.

1993-01-01

Two studies have been conducted in Sweden under contract from SKN-National Board for Spent Nuclear Fuel. The responsibilities of SKN has been transferred to SKI as of July 1, 1992. The first study is related to a compilation of experience and lessons learned from siting of nuclear waste repositories and other controversial facilities in seven countries. The second study is aimed at compiling examples of the state of knowledge related to the regional geological information with relevance to siting of a repository in Sweden. This paper is drawing the general combined conclusions from both these studies. The first study reviewed programs for siting of nuclear and hazardous waste disposal facilities in Canada, Finland, France, Sweden, Switzerland, United Kingdom and USA. The main topics reviewed are related to a/ The use of technical screening, b/ Legal framework and local veto, c/ Public involvement, d/ Interim storage and schedule flexibility, e/ Sequential vs. parallel characterization. The second study focused on the regional geological information available for Sweden and if this information allows for a ''grouping'' of tectonic regions in Sweden with significant differences in history and characteristics. Factors studied as potentially important for siting are bedrock properties, mineralizations, ground water conditions and available volume for a repository. The experience gained from these studies is aimed to be used as background information in the review of the program conducted for the Swedish nuclear utilities by SKB. SKB will according to current plans initiate siting for a repository for spent nuclear fuel in Sweden during 1993. (author). 2 refs

A compound power-law model for volcanic eruptions: Implications for risk assessment of volcanism at the proposed nuclear waste repository at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Ho, Chih-Hsiang

1994-01-01

Much of the ongoing debate on the use of nuclear power plants in U.S.A. centers on the safe disposal of the radioactive waste. Congress, aware of the importance of the waste issue, passed the Nuclear Waste Policy Act of 1982, requiring the federal government to develop a geologic repository for the permanent disposal of high level radioactive wastes from civilian nuclear power plants. The Department of Energy (DOE) established the Office of Civilian Radioactive Waste Management (OCRWM) in 1983 to identify potential sites. When OCRWM had selected three potential sites to study, Congress enacted the Nuclear Waste Policy Amendments Act of 1987, which directed the DOE to characterize only one of those sites, Yucca Mountain, in southern Nevada. For a site to be acceptable, theses studies must demonstrate that the site could comply with regulations and guidelines established by the federal agencies that will be responsible for licensing, regulating, and managing the waste facility. Advocates and critics disagree on the significance and interpretation of critical geological features which bear on the safety and suitability of Yucca Mountain as a site for the construction of a high-level radioactive waste repository. Recent volcanism in the vicinity of Yucca Mountain is readily recognized as an important factor in determining future public and environmental safety because of the possibility of direct disruption of a repository site by volcanism. In particular, basaltic volcanism is regarded as direct and unequivocal evidence of deep-seated geologic instability. In this paper, statistical analysis of volcanic hazard assessment at the Yucca Mountain site is discussed, taking into account some significant geological factors raised by experts. Three types of models are considered in the data analysis. The first model assumes that both past and future volcanic activities follow a homogeneous Poisson process (HPP)

Design criteria development for the structural stability of nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Yun, C H [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Yu, T S [Daewoo Engineering Company, Sungnam (Korea, Republic of); Ko, H M [Seoul National Univ., Seoul (Korea, Republic of)

1990-11-15

The objective of the present project is to develop design criteria for the structural stability of rock cavity for the underground repository are defined, according to which detailed descriptions for design methodologies, design stages and stability analysis of the cavity are made. The proposed criteria can be used as a guide for the preparation of design codes which are to be established as the site condition and technical emplacement procedure are fixed. The present report first reviews basic safety requirements and criteria of the underground disposal of nuclear wastes for the establishment of design concepts and stability analysis of the rock cavity. Important factors for the design are also described by considering characteristics of the wastes and underground facilities. The present project has investigated technical aspects on the design of underground structures based on the currently established underground construction technologies, and presented a proposal for design criteria for the structural stability of the nuclear waste repository. The proposed criteria consist of general provisions, geological exploration, rock classification, design process and methods, supporting system, analyses and instrumentation.

Long-Term Waste Package Degradation Studies at the Yucca Mountain Potential High-Level Nuclear Waste Repository

International Nuclear Information System (INIS)

Mon, K. G.; Bullard, B. E.; Longsine, D. E.; Mehta, S.; Lee, J. H.; Monib, A. M.

2002-01-01

The Site Recommendation (SR) process for the potential repository for spent nuclear fuel (SNF) and high-level nuclear waste (HLW) at Yucca Mountain, Nevada is underway. Fulfillment of the requirements for substantially complete containment of the radioactive waste emplaced in the potential repository and subsequent slow release of radionuclides from the Engineered Barrier System (EBS) into the geosphere will rely on a robust waste container design, among other EBS components. Part of the SR process involves sensitivity studies aimed at elucidating which model parameters contribute most to the drip shield and waste package degradation characteristics. The model parameters identified included (a) general corrosion rate model parameters (temperature-dependence and uncertainty treatment), and (b) stress corrosion cracking (SCC) model parameters (uncertainty treatment of stress and stress intensity factor profiles in the Alloy 22 waste package outer barrier closure weld regions, the SCC initiation stress threshold, and the fraction of manufacturing flaws oriented favorably for through-wall penetration by SCC). These model parameters were reevaluated and new distributions were generated. Also, early waste package failures due to improper heat treatment were added to the waste package degradation model. The results of these investigations indicate that the waste package failure profiles are governed by the manufacturing flaw orientation model parameters and models used

NWTS program criteria for mined geologic disposal of nuclear waste: repository performance and development criteria. Public draft

Energy Technology Data Exchange (ETDEWEB)

None

1982-07-01

This document, DOE/NWTS-33(3) is one of a series of documents to establish the National Waste Terminal Storage (NWTS) program criteria for mined geologic disposal of high-level radioactive waste. For both repository performance and repository development it delineates the criteria for design performance, radiological safety, mining safety, long-term containment and isolation, operations, and decommissioning. The US Department of Energy will use these criteria to guide the development of repositories to assist in achieving performance and will reevaluate their use when the US Nuclear Regulatory Commission issues radioactive waste repository rules.

NWTS program criteria for mined geologic disposal of nuclear waste: repository performance and development criteria. Public draft

International Nuclear Information System (INIS)

1982-07-01

This document, DOE/NWTS-33(3) is one of a series of documents to establish the National Waste Terminal Storage (NWTS) program criteria for mined geologic disposal of high-level radioactive waste. For both repository performance and repository development it delineates the criteria for design performance, radiological safety, mining safety, long-term containment and isolation, operations, and decommissioning. The US Department of Energy will use these criteria to guide the development of repositories to assist in achieving performance and will reevaluate their use when the US Nuclear Regulatory Commission issues radioactive waste repository rules

Processing of nuclear waste

International Nuclear Information System (INIS)

Hennelly, E.J.

1981-01-01

The processing of nuclear waste to transform the liquid waste from fuel reprocessing activities is well defined. Most solid waste forms, if they are cooled and contain diluted waste, are compatible with many permanent storage environments. The public acceptance of methods for disposal is being delayed in the US because of the alternatives studies of waste forms and repositories now under way that give the impression of indecision and difficulty for the disposal of HLW. Conservative programs that dilute and cool solid waste are under way in France and Sweden and demonstrate that a solution to the problem is available now. Research and development should be directed toward improving selected methods rather than seeking a best method, which at best, may always be illusory

The status of radioactive waste repository development in the United States - December 2011

International Nuclear Information System (INIS)

Hill, David R.

2012-01-01

The current state of affairs concerning development in the United States of a permanent repository for disposal of spent nuclear fuel (SNF) and high-level radioactive waste (HLW) is, in a word, uncertain. The President of the United States has asserted that he believes licensing and development of the Yucca Mountain repository should be abandoned, while other important parties believe licensing and development should continue. And not surprisingly, there is a disagreement as to what the law requires and whether the licensing process for the Yucca Mountain repository can be terminated at this point, even if the President would like for that to happen. The future of Yucca Mountain, and the future of radioactive waste disposal in the United States generally, currently are pending before the US Court of Appeals for the District of Columbia Circuit, and eventually the Supreme Court of the United States may decide some of the important legal issues concerning Yucca Mountain's future. The November 2012 US elections also likely will have a significant impact on future radioactive waste repository development

The evolving image and role of the regulator for implementing repositories for nuclear waste and spent nuclear fuel

International Nuclear Information System (INIS)

Melin, J.

2005-01-01

A country introducing nuclear power in their energy strategy has a life long obligation. The obligation is not mainly a question of energy production. It is an obligation to maintain safety during the phase of construction, energy production and decommissioning as well as to take care of all the waste streams from nuclear installations. I believe that one of the most controversial siting projects in the society is a waste repository for spent nuclear fuel. Competence, available funds and a clear responsibility between the stakeholders as well as the trust of the public is indispensable to obtain a good result. The Swedish programme for managing nuclear waste and spent nuclear fuel has been in progress for more than 25 years. The pre-licensing process of a repository for spent nuclear fuel is much alike a pre-licensing process for the first nuclear power plant in a country. You need a clear political will, you have to involve the nuclear regulator without jeopardizing his integrity and you need the money to perform research and make the investments. The enthusiasm of politicians and industry may however differ between these two projects. (author)

Dispute resolution in the nuclear waste repository program

International Nuclear Information System (INIS)

Creighton, J.L.; Shorett, A.J.

1988-01-01

During 1987 a seven-person team addressed just that question for the State of Washington, as part of the studies of the socioeconomic impacts of a possible nuclear waste repository site at the Hanford site. The authors were, respectively, the Mitigation/Compensation team leader and the conflict resolution specialist within the team. While the studies were terminated when Congress selected the Nevada site, the conclusions may still have value for the State of Nevada, or for other controversial federal projects

A global nuclear waste repository

Science.gov (United States)

Lin, Wunan

As a concerned scientist, I think that having a global nuclear waste repository is a reachable goal for human beings. Maybe through this common goal, mankind can begin to treat each other as brothers and sisters. So far, most human activities are framed by national boundaries, which are purely arbitrary. Breaking through these national boundaries will be very beneficial to human beings.Formation of the International Geosphere-Biosphere Program in 1986 indicates a growing awareness on the part of scientists regarding Earth as a system. The Apollo missions gave us a chance to look back at Earth from space. That perspective emphasized that our Earth is just one system: our only home. It is in deed a lonely boat in the high sea of dark space. We must take good care of our “boat.”

Waste inventory, waste characteristics and waste repositories in Japan

International Nuclear Information System (INIS)

Shimooka, K.

1997-01-01

There are two types of repositories for the low level radioactive wastes in Japan. One is a trench type repository only for concrete debris generated from the dismantling of the research reactor. According to the safety assurance system, Japan Atomic Energy Research Institute (JAERI) has disposed of the concrete debris arose from the dismantling of the Japan Power Demonstration Reactor (JPDR). The other type is the concreted pit with engineered barriers. Rokkasho Low Level Radioactive Waste Disposal Center has this type of repository mainly for the power plant wastes. Japan Nuclear Fuel Ltd. (JNFL) established by electric power companies is the operator of the LLW disposal project. JNFL began the storage operation in 1992 and buried approximately 60,000 drums there. Two hundred thousand drums of uniformly solidified, waste may be buried ultimately. 4 refs, 3 tabs

The role of weapons production and military waste in the repository selection process

International Nuclear Information System (INIS)

Nelson, D.; Hope, J.; Power, W.; Hunter, T.

1987-01-01

The decision to commingle defense waste with commercial waste in the nuclear waste repository program has many impacts on that program. There will be more waste to place in the two repositories authorized under the Nuclear Waste Policy Act, more transport miles to get the waste to a repository, and more costs associated with environmental and socio-economic impact mitigation. This paper explores the links between weapons production and military waste, and the repository selection process. The paper first describes the importance of state, tribe and public participation to the acceptance of a repository site selection. The paper then examines the various estimates of amounts of existing and future military nuclear wastes, and how these estimates affect repository siting decisions. The final section addresses the public policy questions which surround this issue. Repository siting may be jeopardized unless there is open public discussion about existing radioactive contamination at military production sites and about future nuclear weapons production. Cost-sharing is considered within this context

Informing future societies about nuclear waste repositories

International Nuclear Information System (INIS)

Jensen, M.

1994-01-01

In 1990 a working group of the NKS (the Nordic nuclear safety program) was formed and give the task of established a basis for a common Nordic view of the need for information conservation for nuclear waste repositories. The Group investigated what tipy of information should be conserved; in what form the information should be kept; the quality of the information; and the problems of future retrieval of information, including retrieval after very long periods of time. Topics covered include the following: scientific aspects including social context of scientific solutions; information management; systems for conservation and retrieval of information including the problems of prediction; archives, markers, archives vs. markers, and continuing processes in society; Archive media including paper documents, microfilm, digital media, media lifetimes; and finally conclusions and recommendations

Performance Assessment of a Generic Repository in Bedded Salt for DOE-Managed Nuclear Waste

Science.gov (United States)

Stein, E. R.; Sevougian, S. D.; Hammond, G. E.; Frederick, J. M.; Mariner, P. E.

2016-12-01

A mined repository in salt is one of the concepts under consideration for disposal of DOE-managed defense-related spent nuclear fuel (SNF) and high level waste (HLW). Bedded salt is a favorable medium for disposal of nuclear waste due to its low permeability, high thermal conductivity, and ability to self-heal. Sandia's Generic Disposal System Analysis framework is used to assess the ability of a generic repository in bedded salt to isolate radionuclides from the biosphere. The performance assessment considers multiple waste types of varying thermal load and radionuclide inventory, the engineered barrier system comprising the waste packages, backfill, and emplacement drifts, and the natural barrier system formed by a bedded salt deposit and the overlying sedimentary sequence (including an aquifer). The model simulates disposal of nearly the entire inventory of DOE-managed, defense-related SNF (excluding Naval SNF) and HLW in a half-symmetry domain containing approximately 6 million grid cells. Grid refinement captures the detail of 25,200 individual waste packages in 180 disposal panels, associated access halls, and 4 shafts connecting the land surface to the repository. Equations describing coupled heat and fluid flow and reactive transport are solved numerically with PFLOTRAN, a massively parallel flow and transport code. Simulated processes include heat conduction and convection, waste package failure, waste form dissolution, radioactive decay and ingrowth, sorption, solubility limits, advection, dispersion, and diffusion. Simulations are run to 1 million years, and radionuclide concentrations are observed within an aquifer at a point approximately 4 kilometers downgradient of the repository. The software package DAKOTA is used to sample likely ranges of input parameters including waste form dissolution rates and properties of engineered and natural materials in order to quantify uncertainty in predicted concentrations and sensitivity to input parameters. Sandia

Anticipated Degradation Modes of Metallic Engineered Barriers for High-Level Nuclear Waste Repositories

Science.gov (United States)

Rodríguez, Martín A.

2014-03-01

Metallic engineered barriers must provide a period of absolute containment to high-level radioactive waste in geological repositories. Candidate materials include copper alloys, carbon steels, stainless steels, nickel alloys, and titanium alloys. The national programs of nuclear waste management have to identify and assess the anticipated degradation modes of the selected materials in the corresponding repository environment, which evolves in time. Commonly assessed degradation modes include general corrosion, localized corrosion, stress-corrosion cracking, hydrogen-assisted cracking, and microbiologically influenced corrosion. Laboratory testing and modeling in metallurgical and environmental conditions of similar and higher aggressiveness than those expected in service conditions are used to evaluate the corrosion resistance of the materials. This review focuses on the anticipated degradation modes of the selected or reference materials as corrosion-resistant barriers in nuclear repositories. These degradation modes depend not only on the selected alloy but also on the near-field environment. The evolution of the near-field environment varies for saturated and unsaturated repositories considering backfilled and unbackfilled conditions. In saturated repositories, localized corrosion and stress-corrosion cracking may occur in the initial aerobic stage, while general corrosion and hydrogen-assisted cracking are the main degradation modes in the anaerobic stage. Unsaturated repositories would provide an oxidizing environment during the entire repository lifetime. Microbiologically influenced corrosion may be avoided or minimized by selecting an appropriate backfill material. Radiation effects are negligible provided that a thick-walled container or an inner shielding container is used.

Hydrological and thermal issues concerning a nuclear waste repository in fractured rocks

International Nuclear Information System (INIS)

Wang, J.S.Y.

1991-12-01

The characterization of the ambient conditions of a potential site and the assessment of the perturbations induced by a nuclear waste repository require hydrological and thermal investigations of the geological formations at different spatial and temporal scales. For high-level wastes, the near-field impacts depend on the heat power of waste packages and the far-field long-term perturbations depend on the cumulative heat released by the emplaced wastes. Surface interim storage of wastes for several decades could lower the near-field impacts but would have relatively small long-term effects if spent fuels were the waste forms for the repository. One major uncertainty in the assessment of repository impacts is from the variation of hydrological properties in heterogeneous media, including the effects of fractures as high-permeability flow paths for containment migration. Under stress, a natural fracture cannot be represented by the parallel plate model. The rock surface roughness, the contact area, and the saturation state in the rock matrix could significantly change the fracture flow. In recent years, the concern of fast flow through fractures in saturated media has extended to the unsaturated zones. The interactions at different scales between fractures and matrix, between fractured matrix unites and porous units, and between formations and faults are discussed

The value and need for long term conservation of information regarding nuclear waste repositories

Energy Technology Data Exchange (ETDEWEB)

Eng, T. [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Jensen, M. [Swedish Radiation Protection Inst., Stockholm (Sweden)

1993-12-31

An important question in safety assessment of all repositories where toxic waste is disposed is how long should information be available to society about the repository and its content? Future societies right to knowledge must be considered and actions must already today be taken to ensure that proper information conservation, transfer and retrieval are provided. Collection of relevant information must be planned for at the research, construction and the operational phase of a repository. One of the main areas for information conservation and transfer is to mitigate future human intrusion. A system for best possible mitigation of human intrusion should with the present knowledge comprise the following parts: (a) development of planning procedures for long-term conservation of gathered information (present and future national and international archives, markers etc.); (b) continuous follow up of the state-of-the-art of information media; (c) preparations for national rules and regulations on nuclear waste information; (d) participation in international cooperation on issues concerning nuclear waste information keeping, transfer and retrieval.

Transient boundary conditions in the frame of THM-processes at nuclear waste repositories

Directory of Open Access Journals (Sweden)

Schanz Tom

2016-01-01

Full Text Available In nuclear waste repositories, initially unsaturated buffer is subjected to constant heat emitted by waste canister in conjunction with peripheral hydration through water from host rock. The transient hydration process can be potraied as transformation of initial heterogeneity towards homogeneity as final stage. In this context, this paper addresses the key issue of hydro mechanical behaviour of compacted buffer in context of clay microstructure and its evolution under repository relevant loading paths and material heterogeneity. This paper also introduces a unique column experiment facility available at Ruhr Universität Bochum, Germany. The facility has been designed as a forerunner of field scale testing program to simulate the transient hydration process of compacted buffer as per German reference disposal concept. The device is unique in terms of having proficiency to capture the transient material response under various possible repository relevant loading paths with higher precision level by monitor the key parameters like temperature, total suction, water content and axial & radial swelling pressure at three different sections along the length of compacted soil sample. In general, a larger spectrum of loading paths/scenarios, which may arise in the nuclear repository, can be covered precisely with existing device.

OPG's deep geologic repository for low and intermediate level waste - recent progress

International Nuclear Information System (INIS)

King, F.K.

2006-01-01

This paper provides a status report on Canada's first project to build a permanent repository for the long-term management of radioactive waste. Ontario Power Generation has initiated a project to construct a deep geologic repository for low- and intermediate-level waste at the Bruce Nuclear Site, at a depth in the range of 600 to 800 m in an Ordovician-age argillaceous limestone formation. The project is currently undergoing an Environmental Assessment and consulting companies in the areas of environmental assessment, geoscientific site characterization, engineering and safety assessment have been hired and technical studies are underway. Seismic surveys and borehole drilling will be initiated in the fall of 2006. The next major milestone for the project is the submission of the Environmental Assessment report, currently scheduled for December 2008. (author)

Uranium, thorium and trace elements in geologic occurrences as analogues of nuclear waste repository conditions

International Nuclear Information System (INIS)

Wollenberg, H.A.; Brookins, D.G.; Cohen, L.H.; Flexser, S.; Abashian, M.; Murphy, M.; Williams, A.E.

1984-01-01

Contact zones between intrusive rocks and tuff, basalt, salt and granitic rock were investigated as possible analogues of nuclear waste repository conditions. Results of detailed studies of contacts between quartz monzonite of Laramide age, intrusive into Precambrian gneiss, and a Tertiary monzonite-tuff contact zone indicate that uranium, thorium and other trace elements have not migrated significantly from the more radioactive instrusives into the country rock. Similar observations resulted from preliminary investigations of a rhyodacite dike cutting basalt of the Columbia River plateau and a kimberlitic dike cutting bedded salt of the Salina basin. This lack of radionuclide migration occurred in hydrologic and thermal conditions comparable to, or more severe than those expected in nuclear waste repository environments and over time periods of the order of concern for waste repositories. Attention is now directed to investigation of active hydrothermal systems in candidate repository rock types, and in this regard a preliminary set of samples has been obtained from a core hole intersecting basalt underlying the Newberry caldera, Oregon, where temperatures presently range from 100 to 265 0 C. Results of mineralogical and geochemical investigations of this core should indicate the alteration mineralogy and behavior of radioelements in conditions analogous to those in the near field of a repository in basalt

An initial study of the behaviour under repository conditions of inactive components of nuclear wastes

International Nuclear Information System (INIS)

Biddle, P.; Rees, J.H.

1988-02-01

This review extends the appreciation of repository behaviour to include the inactive components of wastes and their degradation products. These materials include a wide range of metals and organics, sludges and decommissioning wastes. The effect of degradation products on the solubility of long-lived radionuclides and any active daughters and their sorption on surfaces of the repository are assessed. Research requirements are identified that may help to improve significantly the assessment of the effects of inactive materials. Data required to improve the quality of inventory data on nuclear wastes are listed. (author)

The Pangea concept for an international radioactive waste repository

International Nuclear Information System (INIS)

Kurzeme, M.

1999-01-01

Pangea Resources Australia Pty. Ltd. is engaged in a study to investigate the feasibility of constructing and operating an international radioactive waste repository in Australia. Western Australia in particular has a unique combination of geology, topography and climate which makes it eminently suitable for a deep geological repository for the safe and permanent disposal of radioactive waste. Australia also has the political, social, legal and financial systems, together with the technical capability to make it acceptable as a host nation for an international repository. This paper reviews the origins of the Pangea concept, describes the high isolation approach to site selection, the Pangea integrated waste management system, together with its potential economic impact on Australia

Nuclear Waste Fund fee adequacy: An assessment

International Nuclear Information System (INIS)

1990-11-01

The purpose of this report is to present the Department of Energy's (the Department) analysis of the adequacy of the 1.00 mill per kilowatt-hour (kWh) fee being paid by the utilities generating nuclear power for the permanent disposal of their spent nuclear fuel (SNF). In accordance with the Nuclear Waste Policy Act (NWPA), the SNF would be disposed of in a geologic repository to be developed by the Department. An annual analysis of the fee's adequacy is required by the NWPA

Preliminary assessment of nuclear waste transportation cost and risk for operation of the first repository at candidate sites

International Nuclear Information System (INIS)

Peterson, R.W.; McSweeney, T.I.; Varadarajan, R.V.; Wilmot, E.L.; Cashwell, J.W.; Joy, D.S.

1983-01-01

To support the selection of the first commercial nuclear waste repository site in 1987, environmental analyses of five candidate site locations are currently being performed. The five locations are in the Gulf Interior Region, the Permian Basin, the Paradox Basin, Yucca Mountain and the Hanford reservation. Costs and operational risks associated with the transportation of nuclear wastes to a single repository located in these regions have been calculated for a life-cycle of 26 years

Mining and engineering aspects and variants for the underground construction of a deep geological repository for radioactive waste and spent nuclear fuel

International Nuclear Information System (INIS)

Milchev, M.; Michailov, B.; Nanovska, E.; Harizanov, A.

2003-01-01

The aim of the present report is to investigate and to describe systematically the foreign experience, scientific and technical achievements and stages of development concerning the mining and engineering aspects and variants for underground construction of a deep geological repository for radioactive waste (RAW) and spent nuclear fuel (SNF). The ideal solution in managing the problems with harmful wastes seems to be either to remove them permanently from Earth (which is related with high risks and high costs) or to transform long-lived radionuclides to short-lived radionuclides using nuclear transmutation processes in a reactor or a particle accelerator. The latter is also a complex and immensely costly process and it can only reduce the quantities of some long-lived radionuclides, which can be then disposed in a geological repository. At present, the deep geological disposal remains the only solution for solving the problem with the hazard of storing radioactive wastes. The report submits a brief description and systematization of the performed investigations, accompanied by analysis of the scientific and technical level on world scale. The analysis is related with the particular geological conditions and the existing scientific studies available so far in Bulgaria. The main conclusions are that the complex scientific-technical and engineering problems related with the construction of a deep geological repository for RAW and SNF require long-term scientific investigations and preliminary complex works and it is high time to launch them in Bulgaria. (authors)

Forced cooling of a nuclear waste repository mine drift - a scoping analysis

Energy Technology Data Exchange (ETDEWEB)

Boyd, R D [Sandia National Labs., Albuquerque, NM (USA)

1982-12-01

Nuclear waste repositories, with decay heat generation beneath the mine drift floors, are force-cooled with air so that re-entrance is possible many years after the waste has been buried. A numerical model has been developed which uses heat transfer coefficients as input. It has been demonstrated that mixed (forced and free) convective and surface roughness effects are significant and must be included in future experiments if reliable predictions are to be made of the time required to cool the repository. For example, when repository mine drifts in volcanic tuff are force-cooled, with forced convection being the only energy transport mechanism, it takes approx.= 0.1 year to cool the mine surface to a safe temperature. However, when mixed convection is the primary transport mechanism it takes approx.= 1.0 year to cool the mine. In addition to mixed convection, other effects are delineated.

Mathematical simulation for safety assessment of nuclear waste repositories

International Nuclear Information System (INIS)

Brandstetter, A.; Raymond, J.R.; Benson, G.L.

1979-01-01

Mathematical models are being developed as part of the Waste Isolation Safety Assessment Program (WISAP) for assessing the post-closure safety of nuclear waste storage in geologic formations. The objective of this program is to develop the methods and data necessary to determine potential events that might disrupt the integrity of a waste repository and provide pathways for radionuclides to reach the bioshpere, primarily through groundwater transport. Four categories of mathematical models are being developed to assist in the analysis of potential release scenarios and consequences: (1) release scenario analysis models; (2) groundwater flow models; (3) contaminant transport models; and (4) radiation dose models. The development of the release scenario models is in a preliminary stage; the last three categories of models are fully operational. The release scenario models determine the bounds of potential future hydrogeologic changes, including potentially disruptive events. The groundwater flow and contaminant transport models compute the flowpaths, travel times, and concentrations of radionuclides that might migrate from a repository in the event of a breach and potentially reach the biosphere. The dose models compute the radiation doses to future populations. Reference site analyses are in progress to test the models for application to different geologies, including salt domes, bedded salt, and basalt

Repository waste-handling operations, 1998

International Nuclear Information System (INIS)

Cottam, A.E.; Connell, L.

1986-04-01

The Civilian Radioactive Waste Management Program Mission Plan and the Generic Requirements for a Mined Geologic Disposal System state that beginning in 1998, commercial spent fuel not exceeding 70,000 metric tons of heavy metal, or a quantity of solidified high-level radioactive waste resulting from the reprocessing of such a quantity of spent fuel, will be shipped to a deep geologic repository for permanent storage. The development of a waste-handling system that can process 3000 metric tons of heavy metal annually will require the adoption of a fully automated approach. The safety and minimum exposure of personnel will be the prime goals of the repository waste handling system. A man-out-of-the-loop approach will be used in all operations including the receipt of spent fuel in shipping casks, the inspection and unloading of the spent fuel into automated hot-cell facilities, the disassembly of spent fuel assemblies, the consolidation of fuel rods, and the packaging of fuel rods into heavy-walled site-specific containers. These containers are designed to contain the radionuclides for up to 1000 years. The ability of a repository to handle more than 6000 pressurized water reactor spent-fuel rods per day on a production basis for approximately a 23-year period will require that a systems approach be adopted that combines space-age technology, robotics, and sophisticated automated computerized equipment. New advanced inspection techniques, maintenance by robots, and safety will be key factors in the design, construction, and licensing of a repository waste-handling facility for 1998

Can shale safely host US nuclear waste?

Science.gov (United States)

Neuzil, C.E.

2013-01-01

"Even as cleanup efforts after Japan’s Fukushima disaster offer a stark reminder of the spent nuclear fuel (SNF) stored at nuclear plants worldwide, the decision in 2009 to scrap Yucca Mountain as a permanent disposal site has dimmed hope for a repository for SNF and other high-level nuclear waste (HLW) in the United States anytime soon. About 70,000 metric tons of SNF are now in pool or dry cask storage at 75 sites across the United States [Government Accountability Office, 2012], and uncertainty about its fate is hobbling future development of nuclear power, increasing costs for utilities, and creating a liability for American taxpayers [Blue Ribbon Commission on America’s Nuclear Future, 2012].However, abandoning Yucca Mountain could also result in broadening geologic options for hosting America’s nuclear waste. Shales and other argillaceous formations (mudrocks, clays, and similar clay-rich media) have been absent from the U.S. repository program. In contrast, France, Switzerland, and Belgium are now planning repositories in argillaceous formations after extensive research in underground laboratories on the safety and feasibility of such an approach [Blue Ribbon Commission on America’s Nuclear Future, 2012; Nationale Genossenschaft für die Lagerung radioaktiver Abfälle (NAGRA), 2010; Organisme national des déchets radioactifs et des matières fissiles enrichies, 2011]. Other nations, notably Japan, Canada, and the United Kingdom, are studying argillaceous formations or may consider them in their siting programs [Japan Atomic Energy Agency, 2012; Nuclear Waste Management Organization (NWMO), (2011a); Powell et al., 2010]."

Survey of near-field flow calculations for nuclear waste repositories NMA L21

International Nuclear Information System (INIS)

Wilson, R.N.; Holland, D.H.

1979-11-01

A survey of methods and codes which describe the flow of groundwater and the migration of radioactive waste in and about nuclear repositories was performed. A number of laboratories engaged in studies of waste migration and groundwater flow were visited in order to discuss the general problem and obtain reports of work being performed. The results of this survey are discussed

The influence of geological loading on the structural integrity of an underground nuclear waste repository

International Nuclear Information System (INIS)

Jakeman, N.

1985-08-01

Stresses are developed in underground nuclear waste repositories as a result of applied loads from geological movements caused by the encroachment of ice sheets or seismic activity for example. These stresses may induce fracturing of the waste matrix, repository vault and nearfield host geology. This fracturing will enhance the advective flow and allow more-rapid transfer of radionuclides from their encapsulation through the repository barriers and nearfield host rock. Geological loads may be applied either gradually as in crustal folding or encroachment of ice sheets, or rapidly as in the case of seismic movements. The analysis outlined in this report is conducted with a view to including the effects of geological loading in a probabilistic repository site assessment computer code such as SYVAC. (author)

Radioactive waste isolation in salt: peer review of the Office of Nuclear Waste Isolation's report on Functional Design Criteria for a Repository for High-Level Radioactive Waste

International Nuclear Information System (INIS)

Hambley, D.F.; Russell, J.E.; Busch, J.S.; Harrison, W.; Edgar, D.E.; Tisue, M.W.

1984-08-01

This report summarizes Argonne's review of the Office of Nuclear Waste Isolation's (ONWI's) draft report entitled Functional Design Criteria for High-Level Nuclear Waste Repository in Salt, dated January 23, 1984. Recommendations are given for improving the ONWI draft report

Damage-plasticity model of the host rock in a nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Koudelka, Tomáš; Kruis, Jaroslav, E-mail: kruis@fsv.cvut.cz [Department of Mechanics, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Prague (Czech Republic)

2016-06-08

The paper describes damage-plasticity model for the modelling of the host rock environment of a nuclear waste repository. Radioactive Waste Repository Authority in Czech Republic assumes the repository to be in a granite rock mass which exhibit anisotropic behaviour where the strength in tension is lower than in compression. In order to describe this phenomenon, the damage-plasticity model is formulated with the help of the Drucker-Prager yield criterion which can be set to capture the compression behaviour while the tensile stress states is described with the help of scalar isotropic damage model. The concept of damage-plasticity model was implemented in the SIFEL finite element code and consequently, the code was used for the simulation of the Äspö Pillar Stability Experiment (APSE) which was performed in order to determine yielding strength under various conditions in similar granite rocks as in Czech Republic. The results from the performed analysis are presented and discussed in the paper.

Time to rethink nuclear waste storage

International Nuclear Information System (INIS)

Flynn, J.; Kasperson, R.; Kunreuther, H.; Slovic, P.

1992-01-01

The authors feel that given the levels of public opposition and distrust, congress should scrap the current nuclear waste storage program and reconsider the options. They observe that no compelling reason currently exists for siting a permanent repository at an early date. Technology developed in the past decade, especially dry-cask storage, provides assurance that wastes from commercial reactors can be stored safely for a lengthy period at current sites. In the longer term, reprocessing may reduce the volume of high-level wastes; storage elsewhere than in a geological repository may prove attractive; and experimental techniques such as transmutation - aimed at radically reducing the amount of time that wastes remain highly radioactive - could help solve the problem. In the meantime, the authors suggest that the US must begin a long-term effort to engage the public in a process of active collaboration. In doing so, the US has much to learn from other countries, where innovative approaches and techniques have began to establish public confidence

Sealing a nuclear waste repository in Columbia river basalt: preliminary results

International Nuclear Information System (INIS)

Hodges, F.N.

1980-01-01

The long containment time required of repositories for nuclear waste (10 4 to 10 6 years) requires that materials used for repository seals be stable in the geologic environment of the repository and of proven longevity. A list of candidate materials for sealing a repository in Columbia River Basalts has been prepared and refined through laboratory testing. The most feasible techniques for emplacing preferred plug materials have been identified and the resultant plugs have been evaluated on the basis of design functions. Preconceptual designs for tunnel, shaft, and borehole seals consist of multiple zone plugs with each zone fulfilling one or more design functions. Zones of disturbed rock around tunnels and shafts, resulting from excavation and subsequent stress release, are zones of higher permeability and of possible fluid migration. In preliminary designs the disturbed zones are blocked by cut-off collars filled with low permeability materials

Radioactive Waste Repositories Administration - SURAO

International Nuclear Information System (INIS)

Kucerka, M.

1998-01-01

The Atomic Act specifies, among other things, responsibilities of the government in the field of safe disposal of radioactive wastes. To satisfy this responsibility, the Ministry of Industry and Trade has established the Radioactive Waste Repositories Administration (SURAO). SURAO's major responsibilities include: (a) the preparation, construction, commissioning, operation, and decommissioning of radioactive waste repositories and the monitoring of their environmental impacts; (b) radioactive waste management; (c) spent or irradiated nuclear fuel processing into a form suitable for storage/disposal or reuse; (d) record-keeping of received radioactive wastes and their producers; (e) administration of fund transfers as stipulated by the Atomic Act, Article 27; (f) development of proposals for specification of fees to be paid to the Nuclear Account; (g) responsibility for and coordination of research and development in the field of radioactive waste handling and management; (h) supervision of licensees' margin earmarked for the decommissioning of their facilities; (i) providing services in radioactive waste handling and management; (j) handling and management of radioactive wastes that have been transferred to the Czech Republic from abroad and cannot be sent back; (k) interim administration of radioactive wastes that have become state property. The Statute of the Administration is reproduced in full. (P.A.)

Repository sealing concepts for the Nevada nuclear waste storage Investigations Project

International Nuclear Information System (INIS)

Fernandez, J.A.; Freshley, M.D.

1984-08-01

This report describes concepts for sealing a nuclear waste repository in an unsaturated tuff environment. The repository site under consideration is Yucca Mountain, which is on and adjacent to the Nevada Test Site. The hydrogeology of Yucca Mountain, preliminary repository concepts, functional requirements and performance criteria for sealing, federal and state regulations, and hydrological calculations are considered in developing the sealing concepts. Water flow through the unsaturated zone is expected to be small and generally vertically downward with some potential to occur through discrete fault and fracture zones. These assumptions are used in developing sealing concepts for shafts, ramps, and boreholes. Sealing of discrete, water-producing faults and fracture zones encountered in horizontal emplacement holes and in access and emplacement drifts is also described. 49 references, 21 figures, 6 tables

Uncertainties in sealing a nuclear waste repository in partially saturated tuff

International Nuclear Information System (INIS)

Tillerson, J.R.; Fernandez, J.A.; Hinkebein, T.E.

1989-01-01

Sealing a nuclear waste repository in partially saturated tuff presents unique challenges to assuring performance of sealing components. Design and performance of components for sealing shafts, ramps, drifts, and exploratory boreholes depend on specific features of both the repository design and the site; of particular importance is the hydrologic environment in the unsaturated zone, including the role of fracture flow. Repository design features important to sealing of a repository include the size and location of shaft and ramp accesses, excavation methods, and the underground layout features such as grade (drainage direction) and location relative to geologic structure. Uncertainties about seal components relate to the postclosure environment for the seals, the emplacement methods, the material properties, and the potential performance of the components. An approach has been developed to reduce uncertainties and to increase confidence in seal performance; it includes gathering extensive site characterization data, establishing conservative design requirements, testing seal components in laboratory and field environments, and refining designs of both the seals and the repository before seals are installed. 9 refs., 5 figs., 2 tabs

Technology overview of mined repositories

International Nuclear Information System (INIS)

Gimera, R.; Thirumalai, K.

1982-01-01

Mined repositories present an environmentally viable option for permanent disposal of nuclear waste. This paper reviews the state-of-the-art mining technologies and identifies technological issues and developments necessary to mine a repository in basalt. The thermal loading, isolation, and retrieval requirements of a repository present unique technological challenges unknown to conventional mining practice. The technology issues and developments required in the areas of excavation, roof and ground support, equipment development, instrumentation development, and sealing are presented. Performance assessment methods must be developed to evaluate the adequacies of technologies developed to design, construct, operate, and decommission a repository. A stepwise test-and-development approach is used in the Basalt Waste Isolation Project to develop cost-effective technologies for a repository

Potential host media for a high-level waste repository

Energy Technology Data Exchange (ETDEWEB)

Hustrulid, W

1982-01-01

Earlier studies of burial of radioactive wastes in geologic repositories had concentrated on salt formations for well-publicized reasons. However, under the Carter administration, significant changes were made in the US nuclear waste management program. Changes which were made were: (1) expansion of the number of rock types under consideration; (2) adoption of the multiple-barrier approach to waste containment; (3) additional requirements for waste retrieval; and (4) new criteria proposed by the Nuclear Regulatory Commission for the isolation of high-level waste in geologic repositories. Results of the studies of different types of rocks as repository sites are summarized herein. It is concluded that each generic rock type has certain advantages and disadvantages when considered from various aspects of the waste disposal problem and that characteristics of rocks are so varied that a most favorable or least favorable rock type cannot be easily identified. This lack of definitive characteristics of rocks makes site selection and good engineering barriers very important for containment of the wastes. (BLM)

Some Materials Degradation Issues in the U.S. High-Level Nuclear Waste Repository Study (The Yucca Mountain Project)

Energy Technology Data Exchange (ETDEWEB)

F. Hua; P. Pasupathi; N. Brown; K. Mon

2005-09-19

The safe disposal of radioactive waste requires that the waste be isolated from the environment until radioactive decay has reduced its toxicity to innocuous levels for plants, animals, and humans. All of the countries currently studying the options for disposing of high-level nuclear waste (HLW) have selected deep geologic formations to be the primary barrier for accomplishing this isolation. In U.S.A., the Nuclear Waste Policy Act of 1982 (as amended in 1987) designated Yucca Mountain in Nevada as the potential site to be characterized for high-level nuclear waste (HLW) disposal. Long-term containment of waste and subsequent slow release of radionuclides into the geosphere will rely on a system of natural and engineered barriers including a robust waste containment design. The waste package design consists of a highly corrosion resistant Ni-based Alloy 22 cylindrical barrier surrounding a Type 316 stainless steel inner structural vessel. The waste package is covered by a mailbox-shaped drip shield composed primarily of Ti Grade 7 with Ti Grade 24 structural support members. The U.S. Yucca Mountain Project has been studying and modeling the degradation issues of the relevant materials for some 20 years. This paper reviews the state-of-the-art understanding of the degradation processes based on the past 20 years studies on Yucca Mountain Project (YMP) materials degradation issues with focus on interaction between the in-drift environmental conditions and long-term materials degradation of waste packages and drip shields within the repository system during the 10,000 years regulatory period. This paper provides an overview of the current understanding of the likely degradation behavior of the waste package and drip shield in the repository after the permanent closure of the facility. The degradation scenario discussed in this paper include aging and phase instability, dry oxidation, general and localized corrosion, stress corrosion cracking and hydrogen induced

Some Materials Degradation Issues in the U.S. High-Level Nuclear Waste Repository Study (The Yucca Mountain Project)

International Nuclear Information System (INIS)

Hua, F.; Pasupathi, P.; Brown, N.; Mon, K.

2005-01-01

The safe disposal of radioactive waste requires that the waste be isolated from the environment until radioactive decay has reduced its toxicity to innocuous levels for plants, animals, and humans. All of the countries currently studying the options for disposing of high-level nuclear waste (HLW) have selected deep geologic formations to be the primary barrier for accomplishing this isolation. In U.S.A., the Nuclear Waste Policy Act of 1982 (as amended in 1987) designated Yucca Mountain in Nevada as the potential site to be characterized for high-level nuclear waste (HLW) disposal. Long-term containment of waste and subsequent slow release of radionuclides into the geosphere will rely on a system of natural and engineered barriers including a robust waste containment design. The waste package design consists of a highly corrosion resistant Ni-based Alloy 22 cylindrical barrier surrounding a Type 316 stainless steel inner structural vessel. The waste package is covered by a mailbox-shaped drip shield composed primarily of Ti Grade 7 with Ti Grade 24 structural support members. The U.S. Yucca Mountain Project has been studying and modeling the degradation issues of the relevant materials for some 20 years. This paper reviews the state-of-the-art understanding of the degradation processes based on the past 20 years studies on Yucca Mountain Project (YMP) materials degradation issues with focus on interaction between the in-drift environmental conditions and long-term materials degradation of waste packages and drip shields within the repository system during the 10,000 years regulatory period. This paper provides an overview of the current understanding of the likely degradation behavior of the waste package and drip shield in the repository after the permanent closure of the facility. The degradation scenario discussed in this paper include aging and phase instability, dry oxidation, general and localized corrosion, stress corrosion cracking and hydrogen induced

Gabbro as a host rock for a nuclear waste repository

International Nuclear Information System (INIS)

Ahlbom, K.; Leijon, B.; Smellie, J.; Liedholm, M.

1992-09-01

As an alternative to granitic rocks, gabbro and other basic rock types have been investigated with respect to their suitability to host a nuclear waste repository. The present report summarizes and examines existing geoscientific knowledge of relevance in assessing the potential merits of gabbro as a repository host rock. Implications in terms of site selection, repository construction and post-closure repository performance are also discussed. The objective of the study is to provide a basis for decisions as regards future consideration of the gabbro alternative. It is found that there are rather few gabbro bodies in Sweden, that are potentially of sufficient size to host a repository. Thus, gabbro offers little latitude as regards site selection. In comparison to siting a repository in granitic rocks, this is a major disadvantage, and it may in fact remove gabbro from further consideration. The potential advantages of gabbro refer to repository performance, and include low hydraulic conductivity and a chemical environment promoting efficient radionuclide retardation. However, results from field investigations show that groundwater flow in gabbro bodies is largely controlled by intersecting heterogeneities, in particular granitic dykes, that are significantly more conductive to water than the gabbro. In the far-field scale significant to repository performance, this may reduce or eliminate the potential effects of favourable hydraulic and chemical characteristics of the gabbro itself. In conclusion, there are apparent difficulties associated with siting a repository in gabbro, due to lack of sufficiently large gabbro bodies. On the basis of the present state of knowledge, no decisive differences can be demonstrated when comparing gabbro with granitic rocks, neither with respects to repository construction, nor as regards repository performance. (au)

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the third part of a report of a preliminary study for AECL. It summarizes the topics considered in reports AECL-6188-1 and AECL-6188-2 as requirements for an undergpound repository for disposal of wastes produced by the Canadian Nuclear Fuel Program. (author)

Disposal of high level nuclear wastes: Thermodynamic equilibrium and environment ethics

Institute of Scientific and Technical Information of China (English)

RANA Mukhtar Ahmed

2009-01-01

Contamination of soil, water or air, due to a failure of containment or disposal of high level nuclear wastes, can potentially cause serious hazards to the environment or human health. Essential elements of the environment and radioactivity dangers to it are illustrated. Issues of high level nuclear waste disposal are discussed with a focus on thermodynamic equilibrium and environment ethics. Major aspects of the issues are analyzed and described briefly to build a perception of risks involved and ethical implications. Nuclear waste containment repository should be as close as possible to thermodynamic equilibrium. A clear demonstration about safety aspects of nuclear waste management is required in gaining public and political confidence in any possible scheme of permanent disposal. Disposal of high level nuclear waste offers a spectrum of environment connected challenges and a long term future of nuclear power depends on the environment friendly solution of the problem of nuclear wastes.

Annular air space effects on nuclear waste canister temperatures in a deep geologic waste repository

International Nuclear Information System (INIS)

Lowry, W.E.; Cheung, H.; Davis, B.W.

1980-01-01

Air spaces in a deep geologic repository for nuclear high level waste will have an important effect on the long-term performance of the waste package. The important temperature effects of an annular air gap surrounding a high level waste canister are determined through 3-D numerical modeling. Air gap properties and parameters specifically analyzed and presented are the air gap size, surfaces emissivity, presence of a sleeve, and initial thermal power generation rate; particular emphasis was placed on determining the effect of these variables have on the canister surface temperature. Finally a discussion based on modeling results is presented which specifically relates the results to NRC regulatory considerations

A geologic scenario for catastrophic failure of the Yucca Mountain Nuclear Waste Repository, Nevada

International Nuclear Information System (INIS)

McMackin, M.R.

1993-01-01

A plausible combination of geologic factors leading to failure can be hypothesized for the Yucca Mountain Nuclear Waste Repository. The scenarios is constructed using elementary fault mechanics combined with geologic observations of exhumed faults and published information describing the repository site. The proposed repository site is located in the Basin and Range Province, a region of active crustal deformation demonstrated by widespread seismicity. The Yucca Mountain area has been characterized as tectonically quiet, which in the context of active crustal deformation may indicate the accumulation of the stresses approaching the levels required for fault slip, essentially stick-slip faulting. Simultaneously, dissolution of carbonate rocks in underlying karst aquifers is lowering the bulk strength of the rock that supports the repository site. Rising levels of hydrostatic stress concurrent with a climatically-driven rise in the water table could trigger faulting by decreasing the effective normal stress that currently retards fault slip. Water expelled from collapsing caverns in the underlying carbonate aquifer could migrate upward with sufficient pressure to open existing fractures or create new fractures by hydrofracturing. Water migrating through fractures could reach the repository in sufficient volume to react with heated rock and waste perhaps creating steam explosions that would further enhance fracture permeability. Closure of conduits in the underlying carbonate aquifer could lead to the elevation of the saturated zone above the level of the repository resulting in sustained saturation of radioactive waste in the repository and contamination of through-flowing groundwater

Hydrogeologic effects of natural disruptive events on nuclear waste repositories

International Nuclear Information System (INIS)

Davis, S.N.

1980-06-01

Some possible hydrogeologic effects of disruptive events that may affect repositories for nuclear waste are described. A very large number of combinations of natural events can be imagined, but only those events which are judged to be most probable are covered. Waste-induced effects are not considered. The disruptive events discussed above are placed into four geologic settings. Although the geology is not specific to given repository sites that have been considered by other agencies, the geology has been generalized from actual field data and is, therefore, considered to be physically reasonable. The geologic settings considered are: (1) interior salt domes of the Gulf Coast, (2) bedded salt of southeastern New Mexico, (3) argillaceous rocks of southern Nevanda, and (4) granitic stocks of the Basin and Range Province. Log-normal distributions of permeabilities of rock units are given for each region. Chapters are devoted to: poresity and permeability of natural materials, regional flow patterns, disruptive events (faulting, dissolution of rock forming minerals, fracturing from various causes, rapid changes of hydraulic regimen); possible hydrologic effects of disruptive events; and hydraulic fracturing

Future extension of the Swedish repository for low and intermediate level waste (SFR)

International Nuclear Information System (INIS)

Carlsson, Jan

2006-01-01

The existing Swedish repository for low and intermediate level waste (SFR) is licensed for disposal of short-lived waste originated from operation and maintenance of Swedish nuclear power plants. The repository is foreseen to be extended to accommodate short-lived waste from the future decommissioning of the Nuclear Power Plants. Long-lived waste from operation, maintenance and eventually decommissioning will be stored some years before disposal in a geological repository. This repository can be build either as a further extension of the SFR facility or as a separate repository. This paper discusses the strategy of a step-wise extended repository where the extensions are performed during operation of the existing parts of the repository. It describes the process for licensing new parts of the repository (and re-license of the existing parts). (author)

Investigation on design of repository for radioactive waste

International Nuclear Information System (INIS)

Zhang Boming; Zhang Ruixue; Wang Fengying

2010-01-01

The scheme design of the repository for radioactive waste is introduced according to the traits of radioactive waste in Jiangsu province, such as the style of the repository, lifting facilities, the step for preventing or controlling flood, the aseismatic measure, the pollution prevention and so on. This ensured the radioactive waste and the waste radioactive sources to be stored in security, the area environment not to be polluted. It can improve the use of nuclear technology in Jiangsu province. (authors)

Screening methodology for site selection of a nuclear waste repository in shale formations in Germany

International Nuclear Information System (INIS)

Hoth, P.; Krull, P.; Wirth, H.

2004-01-01

The radioactive waste disposal policy in the Federal Republic of Germany is based on the principle that all types of radioactive waste must be disposed of in deep geological formations. Because of the favourable properties of rock salt and the existence of thick rock salt formations in Germany, so far most of the research in the field of radioactive waste disposal sites was focused on the study of the use of rock salt. In addition, German research organisations have also conducted generic research and development projects in alternative geological formations (Wanner and Brauer, 2001), but a comprehensive evaluation of their utilisation has been only done for parts of the crystalline rocks in Germany. Research projects on argillaceous rocks started relatively late, so that German experience is mainly connected to German research work with the corresponding European Underground Research Laboratories and the exploration of the former Konrad iron mine as a potential repository site for radioactive waste with negligible heat generation. The German Federal Government has signed in 2001 an agreement with national utility companies to end electricity generation by nuclear power. This decision affected the entire German radioactive waste isolation strategy and especially the repository projects. The utility companies agreed upon standstill of exploration at the Gorleben site and the Federal Ministry for the Environment tries to establish a new comprehensive procedure for the selection of a repository site, built upon well-founded criteria incorporating public participation. Step 3 of the planning includes the examination of further sites in Germany and the comparison with existing sites and concepts. Under these circumstances, argillaceous rock (clay and shale) formations are now a special area of interest in Germany and the development of a screening methodology was required for the evaluation of shales as host and barrier rocks for nuclear waste repositories. (author)

Environmental issues of repository licensing: an evaluation of a hypothetical high-level radioactive waste repository

International Nuclear Information System (INIS)

Owen, J.L.; McGinnis, J.T.; Harper, C.M.; Battelle Columbus Labs., OH)

1982-01-01

This paper presents results of an environmental assessment conducted under the direction of the Office of Nuclear Waste Isolation as part of the National Waste Terminal Storage program. The study defined a range of potential environmental effects of constructing, operating, decommissioning, and long-term isolation of a nuclear waste repository. The analytical methodology used to determine potential environmental effects required definition of a hypothetical environmental setting and repository. Potentially applicable regulatory requirements were identified and were used as guidelines to evaluate permitting feasibility. The environmental effects of repository development were analyzed for the two major time periods of concern: short term (the period of construction, operation, and decommissioning) and long term (the isolation period after decommissioning). As a result of this analysis, major environmental uncertainties and issues were identified. 11 references, 5 figures

Planning the rad waste repository - Croatian case

International Nuclear Information System (INIS)

Kucar Dragicevic, S.; Subasic, D.; Lokner, V.

1996-01-01

Radioactive waste is generated in Croatia from various nuclear applications as well as from the Krsko NPP (Slovenian and Croatian joint venture facility). The national programme on radioactive waste management is aimed at straightening existing infrastructure, establishing new (more transparent) system of responsibilities and development of new legislation. The siting of LL/ILW repository is important segments of the whole radioactive waste management cycle. The status and efficiency of the rad waste management infrastructure in the country have the significant influence on all the activities related to the project of repository construction - from the very first phases of preliminary planning and background preparations to advanced phases of the project development. The present status of the Croatian national radioactive waste infrastructure and its influence on the repository project are presented. The role of national legislation and institutional framework are specially discussed. (author)

FFSM, Long-Term Nuclear Waste Repository Site Simulation by Monte-Carlo

International Nuclear Information System (INIS)

Hadlock, L.R.; Hellstrom, D.I.; Mikulis, M.J.B.; Little, A.D.; Golis, M.J.

1988-01-01

1 - Description of program or function: FFSM (Far Field State Model) predicts the approximate geologic and climatic state of a site for a nuclear waste repository over relatively long periods of time. The purpose of FFSM is to represent quantitatively certain events and processes that could alter the effectiveness of one or more natural barriers in a waste isolation system. The barriers treated by the model are primarily components of the geologic environment surrounding the repository, although biosphere components (e.g. climate parameters) that could affect the impact of radionuclide releases are also considered. These components are treated outside the realm of wastes or repository-induced effects, which is indicated by use of the term f ar field . The model treats both natural and man-induced changes in these barriers within a probabilistic framework, and it accounts for cumulative and interactive effects of multiple phenomena. 2 - Method of solution: Fifteen submodels are included in FFSM to account for phenomena that may be of importance individually or in combination in evaluating sites for repositories. These submodels include: undetected features, climate, worldwide glaciation, local glaciation, folding, salt dispersion, magmatic events, faulting, biosphere state, regional deformation, geomorphic processes, dissolution fronts, localized dissolution (breccia pipes), solution mining, and drilling. FFSM can be used in both a deterministic mode, to evaluate interactions or to calculate point values, and a probabilistic mode, to make statistical estimates of future changes. In the probabilistic mode, Monte Carlo simulation is used to generate output probabilities, based on user-supplied input, largely in the form of probability density functions for variable or uncertain parameters

Characterisation of discharge areas of radionuclides originating from nuclear waste repositories

International Nuclear Information System (INIS)

Marklund, L.; Woerman, A.

2008-01-01

In this study, we investigate if there are certain landscape elements that will generally act as discharge areas for radio-nuclides leaking from a subsurface deposit of nuclear waste. We also characterize the typical properties that distinguish these areas from others. Understanding the processes controlling the clustering of discharge to certain areas is an additional topic of study. Landscape topography is the most important driving force for groundwater flow. Because groundwater is the main transporting agent for migrating radio-nuclides, the topography will determine the flow paths of leaking radionuclides. How topography and heterogeneities in the subsurface affect the discharge distribution of the radionuclides is the main scope of this study. An analytical and a numerical model are used. Conclusions are: Our results suggest that the varieties of landscape elements which have potential for receiving significant amounts of radio-nuclides are limited. To save recourses, the surficial radiological assessments should therefore be focused in these areas. Furthermore, the discharge areas of groundwater from repository depth have defining characteristics that distinguish them from discharge areas of shallower groundwater flow cells. Due to the similarities within deep groundwater discharge areas, one can make site-specific analyses of those areas, which have a broad applicability for migration of radio-nuclides originating from a nuclear waste repository (author)(tk)

Review of important rock mechanics studies required for underground high level nuclear waste repository program

Energy Technology Data Exchange (ETDEWEB)

Kwon, S.; Cho, W. J

2007-01-15

Disposal concept adapting room and pillar method, which is a confirmed technique in mining and tunnel construction for long time, has advantages at cost, safety, technical feasibility, flexibility, and international cooperation point of views. Then the important rock mechanics principals and in situ and laboratory tests for understanding the behavior of rock, buffer, and backfill as well as their interactions will be reviewed. The accurate understanding of them is important for developing a safe disposal concept and successful operation of underground repository for permanent disposal of radioactive wastes. First of all, In this study, current status of rock mechanics studies for HLW disposal in foreign countries such as Sweden, USA, Canada, Finland, Japan, and France were reviewed. After then the in situ and laboratory tests for site characterization were summarized. Furthermore, rock mechanics studies required during the whole procedure for the disposal project from repository design to the final closure will be reviewed systematically. This study will help for developing a disposal system including site selection, repository design, operation, maintenance, and closure of a repository in deep underground rock. By introducing the required rock mechanics tests at different stages, it would be helpful from the planning stage to the operation stage of a radioactive waste disposal project.

Review of important rock mechanics studies required for underground high level nuclear waste repository program

International Nuclear Information System (INIS)

Kwon, S.; Cho, W. J.

2007-01-01

Disposal concept adapting room and pillar method, which is a confirmed technique in mining and tunnel construction for long time, has advantages at cost, safety, technical feasibility, flexibility, and international cooperation point of views. Then the important rock mechanics principals and in situ and laboratory tests for understanding the behavior of rock, buffer, and backfill as well as their interactions will be reviewed. The accurate understanding of them is important for developing a safe disposal concept and successful operation of underground repository for permanent disposal of radioactive wastes. First of all, In this study, current status of rock mechanics studies for HLW disposal in foreign countries such as Sweden, USA, Canada, Finland, Japan, and France were reviewed. After then the in situ and laboratory tests for site characterization were summarized. Furthermore, rock mechanics studies required during the whole procedure for the disposal project from repository design to the final closure will be reviewed systematically. This study will help for developing a disposal system including site selection, repository design, operation, maintenance, and closure of a repository in deep underground rock. By introducing the required rock mechanics tests at different stages, it would be helpful from the planning stage to the operation stage of a radioactive waste disposal project

Politics and technology in repository siting: military versus commercial nuclear wastes at WIPP 1972-1985

International Nuclear Information System (INIS)

Downey, G.L.

1985-01-01

During the 1970s, attempts by the federal government to develop a comprehensive system for disposing of nuclear wastes in geologic repositories were plagued by two related political problems; (1) whether or not military and commercial wastes should be buried together in the same repository, and (2) how to define the host state's role in the repository siting mechanism. This article explains why these two problems were connected by showing how they proved to be of decisive importance in the development of the Waste Isolation Pilot Plant (WIPP) project in Carlsbad, New Mexico. Although WIPP was initially conceived as a wholly military facility, The Department of Energy triggered a three-year dispute over the project's scope by proposing in 1978 to include commercial wastes in the repository. The key issue in the dispute concerned the political legitimacy of decision-making mechanisms for repository siting, which depend upon the extent to which they both adequately represent the interests of affected groups and meet an indistinct technical/political criterion of acceptable safety. DOE's ill-fated proposal to mix military and commercial disposal at WIPP demonstrated that the two rely on somewhat different conditions for their legitimacy. The agency overlapped the legitimate authorities of the federal and state governments and gave itself the hopeless task of negotiating a new boundary between them. 50 references, 3 figures

Some political logistics of nuclear waste

International Nuclear Information System (INIS)

Pulsipher, A.G.

1991-01-01

The need for a centralized, federal, interim storage facility for nuclear waste, or MRS, alledgedly has become more urgent because the date for the opening of the permanent repository has been slipped from 2003 to 2010 at the earliest. However, a MRS constrained by the linkages in the Nuclear Waste Policy Act would make little sense and has no support. DOE wants to change the NWPAA linkages but unless the size of the MRS is constrained to approximately that now permitted, DOE's proposal would be so directly antithetical to the strategic vision and political aspirations of opponents of interim storage that it would seriously retard the development of the badly needed political consensus on national nuclear waste disposal policy. A new linkage, an acceptance rate limitation, is analyzed and the argument advanced that it would yield most of the benefits attributed to an MRS by DOE without aggravating the political concerns of MRS opponents

Disposal of high level nuclear wastes: thermodynamic equilibrium and environment ethics

International Nuclear Information System (INIS)

Rana, M.A.

2009-01-01

Contamination of soil, water or air, due to a failure of containment or disposal of high level nuclear wastes, can potentially cause serious hazards to the environment or human health. Essential elements of the environment and radioactivity dangers to it are illustrated. Issues of high level nuclear waste disposal are discussed with a focus on thermodynamic equilibrium and environment ethics. Major aspects of the issues are analyzed and described briefly to build a perception of risks involved and ethical implications. Nuclear waste containment repository should be as close as possible to thermodynamic equilibrium. A clear demonstration about safety aspects of nuclear waste management is required in gaining public and political confidence in any possible scheme of permanent disposal. Disposal of high level nuclear waste offers a spectrum of environment connected challenges and a long term future of nuclear power depends on the environment friendly solution of the problem of nuclear wastes. (authors)

Influence of convective-energy transfer on calculated temperature distributions in proposed hard-rock nuclear waste repositories

Energy Technology Data Exchange (ETDEWEB)

Eaton, R R; Reda, D C [Sandia National Labs., Albuquerque, NM (USA)

1982-06-01

This study assesses the relative influence of convective-energy transfer on predicted temperature distributions for a nuclear-waste repository located in water-saturated rock. Using results for energy transfer by conduction only (no water motion) as a basis of comparison, it is shown that a considerable amount of energy can be removed from the repository by pumping out water that migrates into the drift from regions adjacent to the buried waste canisters. Furthermore, the results show that the influence of convective-energy transfer on mine drift cooling requirements can be significant for cases where the in-situ permeability of the rock is greater than one millidarcy (a regime potentially encountered in repository scenarios).

Geotechnical instrumentation for repository shafts

International Nuclear Information System (INIS)

Lentell, R.L.; Byrne, J.

1993-01-01

The US Congress passed the Nuclear Waste Policy Act in 1980, which required that three distinctly different geologic media be investigated as potential candidate sites for the permanent disposal of high-level nuclear waste. The three media that were selected for study were basalt (WA), salt (TX, LA, MS, UT), and tuff (NV). Preliminary Exploratory Shaft Facilities (ESF) designs were prepared for seven candidate salt sites, including bedded and domal salt environments. A bedded-salt site was selected in Deaf Smith County, TX for detailed site characterization studies and ESF Final Design. Although Congress terminated the Salt Repository Program in 1988, Final Design for the Deaf Smith ESF was completed, and much of the design rationale can be applied to subsequent deep repository shafts. This paper presents the rationale for the geotechnical instrumentation that was designed for construction and operational performance monitoring of the deep shafts of the in-situ test facility. The instrumentation design described herein can be used as a general framework in designing subsequent instrumentation programs for future high-level nuclear waste repository shafts

GIS for the needs of the Radioactive Waste Repository Authority

Directory of Open Access Journals (Sweden)

Jitka Mikšová

2007-06-01

Full Text Available The Radioactive Waste Repository Authority (RAWRA is a state organisation responsible for the management of activities related to the disposal of all existing and future radioactive waste and spent nuclear fuel classed as a waste in Czech Republic. Worldwide, a deep geological repository is considered the highest degree of safety for a nuclear waste disposal. Such a repository has to be built in a stable geological environment ensuring the isolation of the stored radioactive waste from the surrounding environment for a long period of time. The selection of suitable site for the deep geological repository construction is a complicated and long term process. Considering this fact and also in respect to an assumed volume of varied datasets the GIS RAWRA was established to ensure convenient management and availability of data containing spatial information.The system is based on ESRI (ArcInfo including extensions, ArcSDE, ArcIMS, Leica Geosystems (Image Analysis and Microsoft software (MS SQL Server. Resulting datasets from six recommended potentially suitable sites for the location of a geological repository have been incorporated into the geodatabase to date. The necessary analysis was made using ESRI software tools and, in addition, custom applications were developed including the metadata editor, etc. This analysis was carried out with respect to existing geological and non-geological criteria defined for a nuclear waste repository. Finally, all six investigated sites with a total area of 240 km2 were reduced in area, each of them resulting in an area of approximately 10km2 for further detailed characterisation.

Summary of four release consequence analyses for hypothetical nuclear waste repositories in salt and granite

International Nuclear Information System (INIS)

Cole, C.R.; Bond, F.W.

1980-12-01

Release consequence methology developed under the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) program has now been applied to four hypothetical repository sites. This paper summarizes the results of these four studies in order to demonstrate that the far-field methodology developed under the AEGIS program offers a practical approach to the post-closure safety assessment of nuclear waste repositories sited in deep continental geologic formations. The four studies are briefly described and compared according to the following general categories: physical description of the repository (size, inventory, emplacement depth); geologic and hydrologic description of the site and the conceptual hydrologic model for the site; description of release scenario; hydrologic model implementation and results; engineered barriers and leach rate modeling; transport model implementation and results; and dose model implementation and results. These studies indicate the following: numerical modeling is a practical approach to post-closure safety assessment analysis for nuclear waste repositories; near-field modeling capability needs improvement to permit assessment of the consequences of human intrusion and pumping well scenarios; engineered barrier systems can be useful in mitigating consequences for postulated release scenarios that short-circuit the geohydrologic system; geohydrologic systems separating a repository from the natural biosphere discharge sites act to mitigate the consequences of postulated breaches in containment; and engineered barriers of types other than the containment or absorptive type may be useful

Geologic software for nuclear waste repository studies: A quality assurance program

International Nuclear Information System (INIS)

Figuli, S.; English, S.L.

1987-04-01

This paper discusses a Quality Assurance (QA) program that Kent State University (KSU) has implemented for the development of geologic software. The software being developed at KSU will be used in the site characterization of nuclear waste repositories and must meet the requirements of federal regulations. This QA program addresses the development of models that will be used in the evaluation of the long-term climatic stability of three sites in the western US

Nevada Nuclear-Waste-Storage Investigations. Quarterly report, April-June 1982

Energy Technology Data Exchange (ETDEWEB)

None

1982-09-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) are studying the Nevada Test Site (NTS) area to establish whether it would qualify as a licensable location for a commercial nuclear waste repository; determining whether specific underground rock masses in the NTS area are technically acceptable for permanently disposing of highly radioactive solid wastes; and developing and demonstrating the capability to safely handle and store commercial spent reactor fuel and high-level waste. Progress reports for the following eight tasks are presented: systems; waste package; site; repository; regulatory and institutional; test facilities; land acquisition; and program management. Some of the highlights are: A code library was established to provide a central location for documentation of repository performance assessment codes. A two-dimensional finite element code, SAGUARO, was developed for modeling saturated/unsaturated groundwater flow. The results of an initial experiment to determine canister penetration rates due to corrosion indicate the expected strong effect of toxic environmental conditions on the corrosion rate of carbon steel in tuff-conditioned water. Wells USW-H3 and USW-H4 at Yucca Mountain have been sampled for groundwater analysis. A summary characterizing and relating the mineralogy and petrology of Yucca Mountain tuffs was compiled from the findings of studies of core samples from five drill holes.

Managing nuclear waste from power plants

International Nuclear Information System (INIS)

Keeney, R.L.; Winterfeldt, D. von

1994-01-01

National strategies to manage nuclear waste from commercial nuclear power plants are analyzed and compared. The current strategy is to try to operate a repository at Yucca Mountain, Nevada, to dispose storage at a centralized facility or next to nuclear power plants. If either of these is pursued now, the analysis assumes that a repository will be built in 2100 for waste not subsequently put to use. The analysis treats various uncertainties: whether a repository at Yucca Mountain would be licensed, possible theft and misuse of the waste, innovations in repository design and waste management, the potential availability of a cancer cure by 2100, and possible future uses of nuclear waste. The objectives used to compare alternatives include concerns for health and safety, environmental and socioeconomic impacts, and direct economic costs, as well as equity concerns (geographical, intergenerational, and procedural), indirect economic costs, as well as equity concerns (geographical, intergenerational, and procedural), indirect economic costs to electricity ratepayers, federal government responsibility to manage nuclear waste, and implications of theft and misuse of nuclear waste. The analysis shows that currently building an underground repository at Yucca Mountain is inferior to other available strategies by the equivalent of $10,000 million to $50,000 million. This strongly suggests that this policy should be reconsidered. A more detailed analysis using the framework presented would help to define a new national policy to manage nuclear waste. 36 refs., 3 figs., 17 tabs

Salt repository project: Technical progress report for the quarter 1 April--30 June 1987

International Nuclear Information System (INIS)

1987-01-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of Energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation

Salt Repository Project technical progress report for the quarter 1 January--31 March 1987

International Nuclear Information System (INIS)

1988-03-01

This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation. 23 refs., 1 fig

Interaction of nuclear waste panels with shafts and access ramps for a potential repository at Yucca Mountain: Nevada Nuclear Waste Storage Investigations Project

International Nuclear Information System (INIS)

St John, C.M.

1987-09-01

A series of two-dimensional and three-dimensional analyses of a potential nuclear waste repository at Yucca Mountain were performed to estimate the thermal stresses that would be experienced at the possible locations of shafts or ramps providing access to the repository horizon. Two alternative assumptions were made for the initial state of stress, and calculations were performed to investigate behavior at repository scale. The computed states of stress were also used as boundary conditions for a series of analyses of the access ramps and vertical shafts. The results of the repository scale analyses indicated that there is a region above the repository horizon where the horizontal stresses are reduced as a consequence of the thermal loads imposed by waste emplacement. If the initial state of stress is relatively low then the total horizontal stresses near the ground surface above the repository may be tensile. An evaluation of the total stress state relative to the strength of the rock matrix and vertical and near vertical joints indicates that there is no potential for development of new fractures in the matrix, but joints near the surface could be activated if the initial stress state is low. 13 refs., 24 figs., 4 tabs

Postclosure risks of alternative SRP nuclear waste forms in geologic repositories

International Nuclear Information System (INIS)

Cheung, H.; Edwards, L.; Harvey, T.; Revelli, M.

1982-05-01

The postclosure risk of REFERENCE and ALTERNATIVE waste forms for the defense high-level waste at the Savannah River Plant (SRP) were compared by analyses with a computer code, MISER, written to study the effects of repository features in a probabilistic framework. MISER traces radionuclide flows through a network of stream tubes from the repository to risk-sensitive points. Uncertainties in waste form, package properties, and geotechnical data are accounted for with Monte Carlo techniques. Our results show: (1) for generic layered-salt and basalt repositories, the difference in performance between the two waste forms is insignificant; (2) where the doses are sensitive to uncertainties in leaching rates, the doses are orders of magnitude below background; (3) disruptive events contribute only slightly to the risk of a layered-salt repository; (4) simple design alterations have strong effects on near field doses; (5) great care should be exercised in selecting the location at which repository risks are to be measured, calculated, or regulated

Application of systems engineering to determine performance requirements for repository waste packages

International Nuclear Information System (INIS)

Aitken, E.A.; Stimmell, G.L.

1987-01-01

The waste package for a nuclear waste repository in salt must contribute substantially to the performance objectives defined by the Salt Repository Project (SRP) general requirements document governing disposal of high-level waste. The waste package is one of the engineered barriers providing containment. In establishing the performance requirements for a project focused on design and fabrication of the waste package, the systems engineering methodology has been used to translate the hierarchy requirements for the repository system to specific performance requirements for design and fabrication of the waste package, a subsystem of the repository. This activity is ongoing and requires a methodology that provides traceability and is capable of iteration as baseline requirements are refined or changed. The purpose of this summary is to describe the methodology being used and the way it can be applied to similar activities in the nuclear industry

Draft environmental assessment: reference repository location, Hanford Site, Washington. Nuclear Waste Policy Act (Section 112)

International Nuclear Information System (INIS)

1984-12-01

In February 1983, the US Department of Energy (DOE) identified a reference repository location at the Hanford Site in Washington as one of nine potentially acceptable sites for a mined geologic repository for spent nuclear fuel and high-level radioactive waste. To determine their suitability, the reference repository location at the Hanford Site and the eight other potentially acceptable sites have been evaluated in accordance with the DOE's General Guidelines for the Recommendation of Sites for Nuclear Waste Repositories. These evaluations are reported in this draft environmental assessment (EA), which is being issued for public review and comment. The DOE findings and determinations that are based on these evaluations are preliminary and subject to public review and comment. A final EA will be prepared after considering the comments received on the draft EA. The reference repository location at Hanford is located in the Columbia Plateau, one of five distinct geohydrologic settings that are being considered for the first repository. On the basis of the evaluations reported in this draft EA, the DOE has found that the reference repository location at Hanford is not disqualified under the guidelines. The DOE has also found that it is suitable for site characterization because the evidence does not support a conclusion that the site will not be able to meet each of the qualifying conditions specified in the guidelines. On the basis of these findings, the DOE is proposing to nominate the reference repository location at Hanford as one of five sites suitable for characterization. Furthermore, having performed a comparative evaluation of the five sites proposed for nomination, the DOE has determined that the reference repository location at Hanford is one of three sites preferred for site characterization

Information base for waste repository design. Volume 3. Waste/rock interactions

International Nuclear Information System (INIS)

Koplick, C.M.; Pentz, D.L.; Oston, S.G.; Talbot, R.

1979-01-01

This report describes the important effects resulting from interaction between radioactive waste and the rock in a nuclear waste repository. The state of the art in predicting waste/rock interactions is summarized. Where possible, independent numerical calculations have been performed. Recommendations are made pointing out areas which require additional research

Geology and hydrogeology of the proposed nuclear waste repository at Yucca Mountain, Nevada and the surrounding area

International Nuclear Information System (INIS)

Mattson, S.R.; Broxton, D.E.; Buono, A.; Crowe, B.M.; Orkild, P.P.

1989-01-01

In late 1987 Congress issued an amendment to the Nuclear Waste Policy Act of 1982 which directed the characterization of Yucca Mountain, Nevada as the only remaining potential site for the Nation's first underground high-level radioactive waste repository. The evaluation of a potential underground repository is guided and regulated by policy established by the Department of Energy (DOE), Nuclear Regulatory Commission (NRC), Environmental Protection Agency (EPA), Department of Transportation (DOT), and the US Congress. The Yucca Mountain Project is the responsibility of the DOE. The purpose of this field trip is to introduce the present state of geologic and hydrologic knowledge concerning this site. This report describes the field trip. 108 refs., 6 figs., 1 tab

Schwarz methods for discrete elliptic and parabolic problems with an application to nuclear waste repository modellingSchwarz methods for discrete elliptic and parabolic problems with an application to nuclear waste repository modelling

Czech Academy of Sciences Publication Activity Database

Blaheta, Radim; Kohut, Roman; Neytcheva, M.; Starý, Jiří

2007-01-01

Roč. 76, 1-3 (2007), s. 18-27 ISSN 0378-4754 R&D Projects: GA AV ČR 1ET400300415 Institutional research plan: CEZ:AV0Z30860518 Keywords : Overlapping domain decomposition * Schwarz methods * Nuclear waste repository Subject RIV: BA - General Mathematics Impact factor: 0.738, year: 2007

Coupled thermo-hydro-mechanical processes associated with a radioactive waste repository

International Nuclear Information System (INIS)

Tsang, C.F.

1988-01-01

The performance assessment of a nuclear waste geologic repository presents a scientific and technical problem of a scope far beyond the evaluation of most civil and geologic constructions. First performance prediction must be made for tens of thousands of years, and a secondly, in calculating potential leakage rates from a repository to the biosphere the authors must determine not only the mean or average travel time but also the shorter travel times of low concentrations. These two criteria demand an understanding of all significant physical and chemical processes likely to occur around a nuclear waste repository. In particular, processes coupling thermal transfer fluid flow, mechanical deformation and chemical reactors, which may be slow in a laboratory time scale, may become very important. This paper gives a general survey on the subject, with specific examples of a number of relevant coupled thermo-hydro-mechanical processes associated with nuclear waste repository

Politics of nuclear waste

Energy Technology Data Exchange (ETDEWEB)

Colglazier, E.W. Jr. (eds.)

1982-01-01

In November of 1979, the Program in Science, Technology and Humanism and the Energy Committee of the Aspen Institute organized a conference on resolving the social, political, and institutional conflicts over the permanent siting of radioactive wastes. This book was written as a result of this conference. The chapters provide a comprehensive and up-to-date overview of the governance issues connected with radioactive waste management as well as a sampling of the diverse views of the interested parties. Chapter 1 looks in depth of radioactive waste management in the United States, with special emphasis on the events of the Carter Administration as well as on the issues with which the Reagen administration must deal. Chapter 2 compares waste management policies and programs among the industralized countries. Chapter 3 examines the factional controversies in the last administration and Congress over nuclear waste issues. Chapter 4 examines the complex legal questions involved in the federal-state conflicts over nuclear waste management. Chapter 5 examines the concept of consultation and concurrence from the perspectives of a host state that is a candidate for a repository and an interested state that has special concerns regarding the demonstration of nuclear waste disposal technology. Chapter 6 examines US and European perspectives concerning public participation in nuclear waste management. Chapter 7 discusses propaganda in the issues. The epilogue attempts to assess the prospects for consensus in the United States on national policies for radioactive waste management. All of the chapter in this book should be interpreted as personal assessments. (DP)

Politics of nuclear waste

International Nuclear Information System (INIS)

Colglazier, E.W. Jr.

1982-01-01

In November of 1979, the Program in Science, Technology and Humanism and the Energy Committee of the Aspen Institute organized a conference on resolving the social, political, and institutional conflicts over the permanent siting of radioactive wastes. This book was written as a result of this conference. The chapters provide a comprehensive and up-to-date overview of the governance issues connected with radioactive waste management as well as a sampling of the diverse views of the interested parties. Chapter 1 looks in depth of radioactive waste management in the United States, with special emphasis on the events of the Carter Administration as well as on the issues with which the Reagen administration must deal. Chapter 2 compares waste management policies and programs among the industralized countries. Chapter 3 examines the factional controversies in the last administration and Congress over nuclear waste issues. Chapter 4 examines the complex legal questions involved in the federal-state conflicts over nuclear waste management. Chapter 5 examines the concept of consultation and concurrence from the perspectives of a host state that is a candidate for a repository and an interested state that has special concerns regarding the demonstration of nuclear waste disposal technology. Chapter 6 examines US and European perspectives concerning public participation in nuclear waste management. Chapter 7 discusses propaganda in the issues. The epilogue attempts to assess the prospects for consensus in the United States on national policies for radioactive waste management. All of the chapter in this book should be interpreted as personal assessments

Molecular hydrogen: An abundant energy source for bacterial activity in nuclear waste repositories

International Nuclear Information System (INIS)

Libert, M.; Bildstein, O.; Esnault, L.; Jullien, M.; Sellier, R.

2011-01-01

A thorough understanding of the energy sources used by microbial systems in the deep terrestrial subsurface is essential since the extreme conditions for life in deep biospheres may serve as a model for possible life in a nuclear waste repository. In this respect, H 2 is known as one of the most energetic substrates for deep terrestrial subsurface environments. This hydrogen is produced from abiotic and biotic processes but its concentration in natural systems is usually maintained at very low levels due to hydrogen-consuming bacteria. A significant amount of H 2 gas will be produced within deep nuclear waste repositories, essentially from the corrosion of metallic components. This will consequently improve the conditions for microbial activity in this specific environment. This paper discusses different study cases with experimental results to illustrate the fact that microorganisms are able to use hydrogen for redox processes (reduction of O 2 , NO 3- , Fe III) in several waste disposal conditions. Consequences of microbial activity include: alteration of groundwater chemistry and shift in geochemical equilibria, gas production or consumption, bio-corrosion, and potential modifications of confinement properties. In order to quantify the impact of hydrogen bacteria, the next step will be to determine the kinetic rate of the reactions in realistic conditions. (authors)

Molecular hydrogen: An abundant energy source for bacterial activity in nuclear waste repositories

Science.gov (United States)

Libert, M.; Bildstein, O.; Esnault, L.; Jullien, M.; Sellier, R.

A thorough understanding of the energy sources used by microbial systems in the deep terrestrial subsurface is essential since the extreme conditions for life in deep biospheres may serve as a model for possible life in a nuclear waste repository. In this respect, H 2 is known as one of the most energetic substrates for deep terrestrial subsurface environments. This hydrogen is produced from abiotic and biotic processes but its concentration in natural systems is usually maintained at very low levels due to hydrogen-consuming bacteria. A significant amount of H 2 gas will be produced within deep nuclear waste repositories, essentially from the corrosion of metallic components. This will consequently improve the conditions for microbial activity in this specific environment. This paper discusses different study cases with experimental results to illustrate the fact that microorganisms are able to use hydrogen for redox processes (reduction of O 2, NO3-, Fe III) in several waste disposal conditions. Consequences of microbial activity include: alteration of groundwater chemistry and shift in geochemical equilibria, gas production or consumption, biocorrosion, and potential modifications of confinement properties. In order to quantify the impact of hydrogen bacteria, the next step will be to determine the kinetic rate of the reactions in realistic conditions.

Impact of transporting defense high-level waste to a geologic repository

International Nuclear Information System (INIS)

Joy, D.S.; Shappert, L.B.; Boyle, J.W.

1984-12-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) provides for the development of repositories for the disposal of high-level radioactive waste and spent nuclear fuel and requires the Secretary of Energy to evaluate five potential repository sites. One factor that is to be examined is transportation of radioactive materials to such a repository and whether transportation might be affected by shipments to a defense-only repository, or to one that accepts both defense and commercial waste. In response to this requirement, The Department of Energy has undertaken an evaluation of the cost and risk associated with the potential shipments. Two waste-flow scenarios are considered which are related to the total quantity of defense high-level waste which will be placed in a repository. The low-flow case is based on a total of 6700 canisters being transported from one site, while the high-flow case assumes that a total of 20,000 canisters will be transported from three sites. For the scenarios considered, the estimated shipping costs range from $105 million to $257 million depending upon the mode of transport and the repository location. The total risks associated with shipping defense high-level waste to a repository are estimated to be significantly smaller than predicted for other transportation activities. In addition, the cost of shipping defense high-level waste to a repository does not depend on whether the site is a defense-only or a commercial repository. Therefore, the transportation considerations are not a basis for the selection of one of the two disposal options

PIME '98, proposal for opening contribution: Nuclear waste

International Nuclear Information System (INIS)

Raurnolin, Heikki

1998-01-01

Full text: Would a debate about an international nuclear waste repository help us win greater public acceptance for our disposal plans? My opening points will be: - International nuclear waste repositories can be accepted by the public only after the acceptance of national repositories. If there are no accepted national plans or existing national repositories, nobody is accepting any international repository in his or her own country; - The focus of gaining public acceptance should therefore be on the national programmes and on the technology itself, i.e. 'Deep disposal is a safe solution independent on the type of rock formations, crystalline, salt, clay etc.'; - The Finnish situation is quite clear. Our people are rather confident on the stability of our old crystalline granite bedrock. Finnish politicians and ordinary people are very much against accepting high-level waste or spent nuclear fuel of foreign origin to be disposed of in Finland. This was one of the reasons why the Finnish Nuclear Act was amended before Finland joined to EU, so that the import and export of nuclear waste are forbidden; - Our site selection programme in Finland is in a very sensitive phase. The Government has just confirmed the target, site selection at the end of year 2000, and the statutory Environmental Impact Assesment process has just been initiated in four candidate sites. Certain opponents try to frighten people by claiming that accepting the site and the deep disposal of our domestic waste means also definitely accepting the same for foreign waste, in any case for any nuclear waste from other EU countries; - So, all news on discussion about international nuclear waste repositories will create more suspicions against the Finnish nuclear authorities, waste company and utilities. Summary: The answer is no, the debate about international nuclear waste repository does not help us to win greater public acceptance for our disposal plans. (author)

Engineered barrier development for a nuclear waste repository in basalt: an integration of current knowledge

Energy Technology Data Exchange (ETDEWEB)

Smith, M.J.

1980-05-01

This document represents a compilation of data and interpretive studies conducted as part of the engineered barriers program of the Basalt Waste Isolation Project. The overall objective of these studies is to provide information on barrier system designs, emplacement and isolation techniques, and chemical reactions expected in a nuclear waste repository located in the basalts underlying the Hanford Site within the state of Washington. Backfills, waste-basalt interactions, sorption, borehole plugging, etc., are among the topics discussed.

Engineered barrier development for a nuclear waste repository in basalt: an integration of current knowledge

International Nuclear Information System (INIS)

Smith, M.J.

1980-05-01

This document represents a compilation of data and interpretive studies conducted as part of the engineered barriers program of the Basalt Waste Isolation Project. The overall objective of these studies is to provide information on barrier system designs, emplacement and isolation techniques, and chemical reactions expected in a nuclear waste repository located in the basalts underlying the Hanford Site within the state of Washington. Backfills, waste-basalt interactions, sorption, borehole plugging, etc., are among the topics discussed

Repository documentation rethought. A comprehensive approach from untreated waste to waste packages for final disposal

Energy Technology Data Exchange (ETDEWEB)

Anthofer, Anton Philipp; Schubert, Johannes [VPC GmbH, Dresden (Germany)

2017-11-15

The German Act on Reorganization of Responsibility for Nuclear Disposal (Entsorgungsuebergangsgesetz (EntsorgUebG)) adopted in June 2017 provides the energy utilities with the new option of transferring responsibility for their waste packages to the Federal Government. This is conditional on the waste packages being approved for delivery to the Konrad final repository. A comprehensive approach starts with the dismantling of nuclear facilities and extends from waste disposal and packaging planning to final repository documentation. Waste package quality control measures are planned and implemented as early as in the process qualification stage so that the production of waste packages that are suitable for final deposition can be ensured. Optimization of cask and loading configuration can save container and repository volume. Workflow planning also saves time, expenditure and exposure time for personnel at the facilities. VPC has evaluated this experience and developed it into a comprehensive approach.

Hydrothermal conditions around a radioactive waste repository

International Nuclear Information System (INIS)

Thunvik, R.; Braester, C.

1981-12-01

Numerical solutions for the hydrothermal conditions around a hard rock repository for nuclear fuel waste are presented. The objective of the present investigation is to illustrate in principle the effect of heat released from a hypothetical radioactive waste repository with regard to anisotropy in the rock permeability. Permeability and porosity are assumed to be constant or to decrease exponentially with depth. The hypothetical repository is situated below a horizontal ground surface or below the crest of a hill, and it is assumed that the water table follows the topography. Major interest in the analysis is directed towards the influence of anisotropy in the permeability on the flow patterns and travel times for water particles, being traced from the repository to the ground surface. The presented results show that anisotropy in the permeability may have a significant influence on the flow conditions around the repository and subsequently also on the travel times from the repository. (Authors)

Radiation effects on materials in the near-field of nuclear waste repository. 1998 annual progress report

International Nuclear Information System (INIS)

Ewing, R.C.; Wang, L.M.

1998-01-01

'Site restoration activities at DOE facilities and the permanent disposal of nuclear waste generated at DOE facilities involve working with and within various types and levels of radiation fields. Once the nuclear waste is incorporated into a final form, radioactive decay will decrease the radiation field over geologic time scales, but the alpha-decay dose for these solids will still reach values as high as 10 18 alpha-decay events/gm in periods as short as 1,000 years. This dose is well within the range for which important chemical (e.g., increased leach rate) and physical (e.g., volume expansion) changes may occur in crystalline ceramics. Release and sorption of long-lived actinides (e.g., 237 Np) can provide a radiation exposure to backfill materials, and changes in important properties (e.g., cation exchange capacity) may occur. The objective of this research program is to evaluate the long term radiation effects in the materials in the near-field of a nuclear waste repository with accelerated experiments in the laboratory using energetic particles (electrons, ions and neutrons). Experiments on the microstructural evolution during irradiation of two important groups of materials, sheet silicates (e.g., clays) and zeolites (analcime), have been conducted; and studies of radiation-induced changes in chemical properties (e.g. cation exchange capacity) are underway. As of the mid-2nd year of the 3-year project, experiments on the microstructural evolution during irradiation of two important group of materials, sheet silicates (mica) and zeolites (analcime), have been conducted; and studies of radiation-induced changes in chemical properties (e.g., cation exchange capacity) are underway.'

A geotechnical evaluation of potentially acceptable sites for a high-level nuclear waste repository near the Red Lake Indian Reservation

International Nuclear Information System (INIS)

1986-01-01

The scope and work which served as the basis for this report included the following major activities; (1) A review and summary of the screening methodologies utilized by DOE for the selection of proposed nuclear waste repository sites, including a description of the inherent weakness in those methodologies. (2) A description of the geologic and hydrologic features of the rock bodies selected by DOE and an identification of those features which could result in hazardous conditions as a result of the location of a high-level nuclear waste repository. (3) An assessment of potential environmental impacts of the repository and discussion of endanged species in the proposed repository project areas. This report is organized in three major sections in relationship to the scope of work. A list of references is also included at the end of this report. 37 refs., 2 figs

Nuclear waste. DOE has terminated research evaluating crystalline rock for a repository

International Nuclear Information System (INIS)

Fultz, Keith O.; Sprague, John W.; Weigel, Dwayne E.; Price, Vincent P.

1989-05-01

We found that DOE terminated funding of research projects specifically designed to evaluate the suitability of crystalline rock for a repository. DOE continued other research efforts involving crystalline rock because they will provide information that it considers useful for evaluating the suitability of Yucca Mountain, Nevada, for a potential repository. Such research activities are not prohibited by the amendments. In January 1988, DOE began evaluating both its domestic and international research programs to ensure their compliance with the 1987 amendments. Several DOE offices and contractors were involved in the evaluation. DOE officials believe that the evaluation effectively brought the Office of Civilian Radioactive Waste Management activities into compliance with the amendments while maintaining useful international relations of continuing benefit to the nuclear waste program in general and to DOE's investigation of the Yucca Mountain site in particular. (The 1987 amendments designated Yucca Mountain as the only site that DOE is to investigate for a potential repository.) The approach and results of DOE's evaluation are discussed. Our review of DOE documents indicates that, by June 22, 1988, DOE completed its evaluation of ongoing crystalline rock research projects to ensure compliance with the 1987 amendments, terminated those research activities it identified as being specifically designed to evaluate the suitability of crystalline rock for a repository, continued some research activities involving crystalline rock because these activities would benefit the investigation and development of the Yucca Mountain repository site, and redirected some research activities so that they would contribute to investigating and developing the Yucca Mountain site

Albedo Neutron Dosimetry in a Deep Geological Disposal Repository for High-Level Nuclear Waste.

Science.gov (United States)

Pang, Bo; Becker, Frank

2017-04-28

Albedo neutron dosemeter is the German official personal neutron dosemeter in mixed radiation fields where neutrons contribute to personal dose. In deep geological repositories for high-level nuclear waste, where neutrons can dominate the radiation field, it is of interest to investigate the performance of albedo neutron dosemeter in such facilities. In this study, the deep geological repository is represented by a shielding cask loaded with spent nuclear fuel placed inside a rock salt emplacement drift. Due to the backscattering of neutrons in the drift, issues concerning calibration of the dosemeter arise. Field-specific calibration of the albedo neutron dosemeter was hence performed with Monte Carlo simulations. In order to assess the applicability of the albedo neutron dosemeter in a deep geological repository over a long time scale, spent nuclear fuel with different ages of 50, 100 and 500 years were investigated. It was found out, that the neutron radiation field in a deep geological repository can be assigned to the application area 'N1' of the albedo neutron dosemeter, which is typical in reactors and accelerators with heavy shielding. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Importance of creep failure of hard rock in the near field of a nuclear-waste repository

International Nuclear Information System (INIS)

Blacic, J.D.

1981-01-01

Potential damage resulting from slow creep deformation intuitively seems unlikely for a high-level nuclear waste repository excavated in hard rock. However, recent experimental and modeling results indicate that the processes of time-dependent microcracking and water-induced stress corrosion can lead to significant reductions in strength and alteration of other key rock properties in the near-field region of a repository. We review the small data base supporting these conclusions and stress the need for an extensive laboratory program to obtain the new data that will be required for design of a repository

Importance of creep failure of hard rock in the near field of a nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Blacic, J D [Los Alamos National Laboratory, NM, (USA)

1982-12-31

Potential damage resulting from slow creep deformation intuitively seems unlikely for a high-level nuclear waste repository excavated in hard rock. However, recent experimental and modeling results indicate that the processes of time-dependent microcracking and water-induced stress corrosion can lead to significant reductions in strength and alteration of other key rock properties in the near-field region of a repository. We review the small data base supporting these conclusions and stress the need for an extensive laboratory program to obtain the new data that will be required for design of a repository.

Reversing nuclear opposition: evolving public acceptance of a permanent nuclear waste disposal facility.

Science.gov (United States)

Jenkins-Smith, Hank C; Silva, Carol L; Nowlin, Matthew C; deLozier, Grant

2011-04-01

Nuclear facilities have long been seen as the top of the list of locally unwanted land uses (LULUs), with nuclear waste repositories generating the greatest opposition. Focusing on the case of the Waste Isolation Pilot Plant (WIPP) in southern New Mexico, we test competing hypotheses concerning the sources of opposition and support for siting the facility, including demographics, proximity, political ideology, and partisanship, and the unfolding policy process over time. This study tracks the changes of risk perception and acceptance of WIPP over a decade, using measures taken from 35 statewide surveys of New Mexico citizens spanning an 11-year period from fall 1990 to summer 2001. This time span includes periods before and after WIPP became operational. We find that acceptance of WIPP is greater among those whose residences are closest to the WIPP facility. Surprisingly, and contrary to expectations drawn from the broader literature, acceptance is also greater among those who live closest to the nuclear waste transportation route. We also find that ideology, partisanship, government approval, and broader environmental concerns influence support for WIPP acceptance. Finally, the sequence of procedural steps taken toward formal approval of WIPP by government agencies proved to be important to gaining public acceptance, the most significant being the opening of the WIPP facility itself. © 2010 Society for Risk Analysis.

Salt repository project closeout status report

International Nuclear Information System (INIS)

1988-06-01

This report provides an overview of the scope and status of the US Department of Energy (DOE's) Salt Repository Project (SRP) at the time when the project was terminated by the Nuclear Waste Policy Amendments Act of 1987. The report reviews the 10-year program of siting a geologic repository for high-level nuclear waste in rock salt formations. Its purpose is to aid persons interested in the information developed during the course of this effort. Each area is briefly described and the major items of information are noted. This report, the three salt Environmental Assessments, and the Site Characterization Plan are the suggested starting points for any search of the literature and information developed by the program participants. Prior to termination, DOE was preparing to characterize three candidate sites for the first mined geologic repository for the permanent disposal of high-level nuclear waste. The sites were in Nevada, a site in volcanic tuff; Texas, a site in bedded salt (halite); and Washington, a site in basalt. These sites, identified by the screening process described in Chapter 3, were selected from the nine potentially acceptable sites shown on Figure I-1. These sites were identified in accordance with provisions of the Nuclear Waste Policy Act of 1982. 196 refs., 21 figs., 11 tabs

The importance of counting cows: Social and economic effects of a high-level nuclear waste repository in Texas

International Nuclear Information System (INIS)

Fleishman, J.; Brody, J.; Galavotti, C.

1987-01-01

Impact assessments that rely on existing records and extrapolation from broad geographic areas provide inadequate information about social and economic conditions important in siting a high-level nuclear waste repository. Texas has used an alternative approach, involving systematic surveys of representative samples of local residents, farm operators and businesses in the proposed site counties and comparison areas. Results show that this technique is useful in describing current economic conditions, including characteristics of key sectors of the economy, changes related to the siting process, and expectations that may influence investment. In addition, the surveys are useful in assessing the degree of consensus in local communities and in identifying possible differential effects of a repository on particular groups. They also provide a baseline for long-term monitoring of repository effects and contribute to their understanding of the underlying processes that shape public response to the nuclear waste program

Managing the nation's nuclear waste. Site descriptions: Cypress Creek, Davis Canyon, Deaf Smith, Hanford Reference, Lavender Canyon, Richton Dome, Swisher, Vacherie Dome, and Yucca Mountain

International Nuclear Information System (INIS)

1985-01-01

In 1982, the Congress enacted the Nuclear Waste Policy Act (Public Law 97-425), which established a comprehensive national program directed toward siting, constructing, and operating geologic repositories for the permanent disposal of high-level radioactive waste. In February 1983, the United States Department of Energy (DOE) identified the nine referenced repository locations as potentially acceptable sites for a mined geologic repository. These sites have been evaluated in accordance with the DOE's General Guidelines for the Recommendation of Sites for Nuclear Waste Repositories. The DOE findings and determinations are based on the evaluations contained in the draft Environmental Assessments (EA). A final EA will be prepared after considering the comments received on the draft EA. The purpose of this document is to provide the public with specific site information on each potential repository location

Aerosol particle transport modeling for preclosure safety studies of nuclear waste repositories

International Nuclear Information System (INIS)

Gelbard, F.

1989-01-01

An important concern for preclosure safety analysis of a nuclear waste repository is the potential release to the environment of respirable aerosol particles. Such particles, less than 10 μm in aerodynamic diameter, may have significant adverse health effects if inhaled. To assess the potential health effects of these particles, it is not sufficient to determine the mass fraction of respirable aerosol. The chemical composition of the particles is also of importance since different radionuclides may pose vastly different health hazards. Thus, models are needed to determine under normal and accident conditions the particle size and the chemical composition distributions of aerosol particles as a function of time and of position in the repository. In this work a multicomponent sectional aerosol model is used to determine the aerosol particle size and composition distributions in the repository. A range of aerosol mass releases with varying mean particle sizes and chemical compositions is used to demonstrate the sensitivities and uncertainties of the model. Decontamination factors for some locations in the repository are presented. 8 refs., 1 tab

Hydrothermal modeling for the efficient design of thermal loading in a nuclear waste repository

International Nuclear Information System (INIS)

Cho, Won-Jin; Kim, Jin-Seop; Choi, Heui-Joo

2014-01-01

Highlights: • Three-dimensional hydrothermal modeling for HLW repository is performed. • The model reduces the peak temperature in the repository by about 10 °C. • Decreasing the tunnel distance is more efficient to improve the disposal density. • The EDZ surrounding the deposition hole increases the peak temperature. • The peak temperature for the double-layer repository remains below the limit. - Abstract: The thermal analysis of a geological repository for nuclear waste using the three-dimensional hydrothermal model is performed. The hydrothermal model reduces the maximum peak temperature in the repository by about 10 °C compared to the heat conduction model with constant thermal conductivities. Decreasing the tunnel distance is more efficient than decreasing the deposition hole spacing to improve the disposal density for a given thermal load. The annular excavation damaged zone surrounding the deposition hole has a considerable effect on the peak temperature. The possibility of double-layer repository is analyzed from the viewpoint of the thermal constraints of the repository. The maximum peak temperature for the double-layer repository is slightly higher than that for the single-layer repository, but remains below the temperature limit

Calculation of financial compensation due of municipalities hosting nuclear waste deposit

International Nuclear Information System (INIS)

Silva, Renata A. da; Simoes, Francisco Fernando L.; Martins, Vivian B.

2011-01-01

The present work evaluates the math from monthly financial transfers to municipalities with technical viability for building of initial or intermediate repository for storing of radioactivity nuclear waste: gloves, sneakers, mask, resins and filters came from thermonuclear facilities. Several aspects have been considered as the geological factors of the site as presence of capable faults, groundwater vulnerability, infiltration of seawater. Also, it was take into account socioeconomic factors: population density, costs for construction, maintenance and operation of repository; size and activity of waste; among others. Hereafter, we have presented the key features of low and average activity repository and high activity repository even as initial, intermediate and final repository and the possible environment impact. The methodology for calculation of financial compensation of municipalities was established by CNEN will be applied for a specific assumed municipality. The analysis of financial compensation due to the specific nuclear waste deposit and the possible guidelines for the use of that compensation by the municipality will be analyzed. In addiction, it will be compared the model for compensation used for nuclear wastes with other plants receiving permanent wastes from cemeteries and sanitary landfills, where the land should not be allowed for the human activities the same as: crops, livestock and buildings. Also, comparison with royalties and indemnities were paid by facilities of energy production as hydroelectric dams as well as petroleum and gas exploration plants. The destination of financial compensation transfer to the municipality is in charge of the city administration. The compensation could be applied of investments in education and culture, health, sanitation works, improvement of public transport, environment, among others. It will be discussed the cost-benefit relation for the assumed municipality. (author)

Calculation of financial compensation due of municipalities hosting nuclear waste deposit

Energy Technology Data Exchange (ETDEWEB)

Silva, Renata A. da, E-mail: renata.amaral@ufrj.b [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Simoes, Francisco Fernando L.; Martins, Vivian B., E-mail: flamego@ien.gov.b [Instituto de Engenharia Nuclear (LIMA/IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Lab. Impactos Ambientais

2011-07-01

The present work evaluates the math from monthly financial transfers to municipalities with technical viability for building of initial or intermediate repository for storing of radioactivity nuclear waste: gloves, sneakers, mask, resins and filters came from thermonuclear facilities. Several aspects have been considered as the geological factors of the site as presence of capable faults, groundwater vulnerability, infiltration of seawater. Also, it was take into account socioeconomic factors: population density, costs for construction, maintenance and operation of repository; size and activity of waste; among others. Hereafter, we have presented the key features of low and average activity repository and high activity repository even as initial, intermediate and final repository and the possible environment impact. The methodology for calculation of financial compensation of municipalities was established by CNEN will be applied for a specific assumed municipality. The analysis of financial compensation due to the specific nuclear waste deposit and the possible guidelines for the use of that compensation by the municipality will be analyzed. In addiction, it will be compared the model for compensation used for nuclear wastes with other plants receiving permanent wastes from cemeteries and sanitary landfills, where the land should not be allowed for the human activities the same as: crops, livestock and buildings. Also, comparison with royalties and indemnities were paid by facilities of energy production as hydroelectric dams as well as petroleum and gas exploration plants. The destination of financial compensation transfer to the municipality is in charge of the city administration. The compensation could be applied of investments in education and culture, health, sanitation works, improvement of public transport, environment, among others. It will be discussed the cost-benefit relation for the assumed municipality. (author)

Nuclear waste: our radioactive hot potato

International Nuclear Information System (INIS)

Conselman, F.B.

1984-01-01

Nuclear industry inevitably produces nuclear waste, whose prudent, prompt and economic disposal is important to the national welfare. Technological problems of containment and isolation have apparently been solved. Underground or geologic disposal sites have the potential form permanent isolation, with salt, basalt, granite, shale, and tuff currently receiving principal attention as repository host rocks. Bedded salt deposits may offer the principal mechanical advantages, but in the northwestern United States the abundance of basalt at existing test sites has made it the subject of experimentation. However, psychological, political, and allegedly environmental obstructionism have stalled the process and virtually immobilized current construction. A program is suggested with the purpose of satisfying technical requirements for public protection while allaying the exaggerated fears of anti-nuclear factions

Overall review strategy for the Nuclear Regulatory Commission's High-Level Waste Repository Program

International Nuclear Information System (INIS)

Johnson, R.L.

1994-11-01

The Overall Review Strategy gives general guidance to the Nuclear Regulatory Commission staff for conducting it's license application and pre-license application reviews. These reviews are in support of the Commission's construction authorization decision for a geologic repository for the disposal of high-level radioactive waste. Objectives and strategies are defined that focus the staff's reviews on determining compliance with requirements of 10 CFR Part 60. These strategies define how the staff prioritizes its reviews on those key technical uncertainties considered to be most important to repository performance. Strategies also give guidance for developing, in an integrated way, the License Application Review Plan together with supporting performance assessments, analyses, and research

Scenario Analysis for the Safety Assessment of Nuclear Waste Repositories: A Critical Review.

Science.gov (United States)

Tosoni, Edoardo; Salo, Ahti; Zio, Enrico

2018-04-01

A major challenge in scenario analysis for the safety assessment of nuclear waste repositories pertains to the comprehensiveness of the set of scenarios selected for assessing the safety of the repository. Motivated by this challenge, we discuss the aspects of scenario analysis relevant to comprehensiveness. Specifically, we note that (1) it is necessary to make it clear why scenarios usually focus on a restricted set of features, events, and processes; (2) there is not yet consensus on the interpretation of comprehensiveness for guiding the generation of scenarios; and (3) there is a need for sound approaches to the treatment of epistemic uncertainties. © 2017 Society for Risk Analysis.

Use of virtual reality for the development of a nuclear waste repository for training

International Nuclear Information System (INIS)

Avellar, Ricardo Fernandes de; Mól, Antônio Carlos A.; Machado, Daniel Mol; Santo, André Cotelli do E.; Legey, Ana Paula

2017-01-01

In Brazil the highest amount of waste generated is low and medium level of radiation. Its management and final destination is important for society and the solution, proposed by the government, involves the construction of a National Repository for Radioactive Waste. Using Virtual Reality (VR), this article aims to develop an interactive virtual model of the repository to assist in the study, evaluation, training of personnel and planning of the installation to be implemented. The method was divided into four steps. The first, called 'Requirements Specification and Survey', aimed at acquiring information about the terrain and future buildings of the installation in the real world. The next step, known as 'Modeling the Environment' is the construction of the virtual environment itself according to the specifications of the previous method. The third, called 'Functionality Implementation' consists of inserting functionalities into the system, such as performing some tasks present in the repository. Finally, the last step is the interactive virtual model of the national repository for radioactive waste, with this tool users can study, evaluate and train conditions/situations of the installation. In conclusion, the results have shown that the tool presented in this work is a possible application of the VR for dissemination and training in nuclear installations. Using this tool, users can visualize and plan strategies to be carried out in a repository, without interrupting the operation of the installation. It can be used for training and operations simulations, aiming to improve the processes without exposing the operators to the radiation. (author)

Use of virtual reality for the development of a nuclear waste repository for training

Energy Technology Data Exchange (ETDEWEB)

Avellar, Ricardo Fernandes de; Mól, Antônio Carlos A.; Machado, Daniel Mol, E-mail: ricardo.arq2017@gmail.com, E-mail: mol@ien.gov.br, E-mail: machado.mol@gmail.com [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Santo, André Cotelli do E.; Legey, Ana Paula, E-mail: cotelli.andre@gmail.com [Centro Universitário Carioca (UniCarioca), Rio de Janeiro, RJ (Brazil)

2017-07-01

In Brazil the highest amount of waste generated is low and medium level of radiation. Its management and final destination is important for society and the solution, proposed by the government, involves the construction of a National Repository for Radioactive Waste. Using Virtual Reality (VR), this article aims to develop an interactive virtual model of the repository to assist in the study, evaluation, training of personnel and planning of the installation to be implemented. The method was divided into four steps. The first, called 'Requirements Specification and Survey', aimed at acquiring information about the terrain and future buildings of the installation in the real world. The next step, known as 'Modeling the Environment' is the construction of the virtual environment itself according to the specifications of the previous method. The third, called 'Functionality Implementation' consists of inserting functionalities into the system, such as performing some tasks present in the repository. Finally, the last step is the interactive virtual model of the national repository for radioactive waste, with this tool users can study, evaluate and train conditions/situations of the installation. In conclusion, the results have shown that the tool presented in this work is a possible application of the VR for dissemination and training in nuclear installations. Using this tool, users can visualize and plan strategies to be carried out in a repository, without interrupting the operation of the installation. It can be used for training and operations simulations, aiming to improve the processes without exposing the operators to the radiation. (author)

Recommended new criteria for the selection of nuclear waste repository sites in Columbia River basalt and US Gulf Coast domed salt

International Nuclear Information System (INIS)

Steinborn, T.L.; Wagoner, J.L.; Qualheim, B.; Fitts, C.R.; Stetkar, R.E.; Turnbull, R.W.

1980-01-01

Screening criteria and specifications are recommended to aid in the evaluation of sites proposed for nuclear waste disposal in basalt and domed salt. The recommended new criteria proposed in this report are intended to supplement existing repository-related criteria for nuclear waste disposal. The existing criteria are contained in 10 CFR 60 sections which define siting criteria of the Nuclear Regulatory Commission (NRC), and ONWI 33(2) which defines siting criteria of the Office of Nuclear Waste Isolation (ONWI) for the Department of Energy. The specifications are conditions or parameter values that the authors recommend be applied in site acceptance evaluations. The siting concerns covered in this report include repository depth, host rock extent, seismic setting, structural and tectonic conditions, groundwater and rock geochemistry, volcanism, surface and subsurface hydrology, and socioeconomic issues, such as natural resources, land use, and population distribution

Literature survey on solid and aqueous species of importance for nuclear waste repositories: The elements uranium, neptunium and cesium

International Nuclear Information System (INIS)

Bucher, J.J.

1987-01-01

This document contains extensive tables listing all possible chemical compounds of species that might occur in a proposed nuclear waste repository. Most are listed as unlikely to occur under conditions predicted for the repository. Extensive data tables and reference sources are provided for those compounds that might occur on form

Migration of radionuclides through backfill in a nuclear waste repository

International Nuclear Information System (INIS)

Lung, H.

1986-01-01

Four models are analyzed to predict the performance of a backfill layer as part of the waste package emplacement in a nuclear waste repository. The corresponding computer code for each model is also developed. The time-dependent mass transfer analysis on a spherical waste-backfill geometry indicates that the radioactive decay effect can enhance the mass transfer rate from the backfill instead of reducing it. The analysis yields the breakthrough time of the backfill layer, which in turn characterizes the backfill performance. A non-linear (Langmuir) sorption isotherm is used to describe the sorption saturation in the backfill. The steady state mass transport analysis through a prolate spheroidal waste-backfill geometry shows that a simple formula can be used to calculate the individual resistances to mass transport in backfill and in host rock. A general, non-recursive analytical solution is derived for a radioactive decay chain of arbitrary length in either a finite or a semi-infinite medium. Numerical examples are given for different boundary conditions and for different decay chains. The results justify that for a backfill layer made of low permeability material, a zero water velocity can be used in the backfill analysis. It is also shown that under normal repository conditions, the mass transfer rate from the backfill is quite small. For the daughter member with a smaller retardation coefficient than that of the mother nuclide, such as 226 Ra in the 234 U → 230 Th → 226 Ra chain, an interior maximum in the concentration profile appears in the backfill. This phenomenon can be seen only in a chain calculation

Operational procedures for receiving, packaging, emplacing, and retrieving high-level and transuranic waste in a geologic repository in TUFF

International Nuclear Information System (INIS)

Dennis, A.W.; Mulkin, R.

1984-01-01

The Nevada Nuclear Waste Storage Investigations Project, directed by the Nevada Operations Office of the Department of Energy, is currently developing conceptual designs for a commercial nuclear waste repository. In this paper, the preliminary repository operating plans are identified and the proposed repository waste inventory is discussed. The receipt rates for truck and rail car shipments of waste are determined as are the required repository waste emplacement rates

Waste acceptance product specifications for vitrified high-level waste forms

International Nuclear Information System (INIS)

Applewhite-Ramsey, A.; Sproull, J.F.

1993-01-01

The Nuclear Waste Policy Act of 1982 mandated that all high-level waste (HLW) be sent to a federal geologic repository for permanent disposal. DOE published the Environmental Assessment in 1982 which identified borosilicate glass as the chosen HLW form. 1 In 1985 the Department of Energy instituted a Waste Acceptance Process to assure that DWPF glass waste forms would be acceptable to such a repository. This assurance was important since production of waste forms will precede repository construction and licensing. As part of this Waste Acceptance Process, the DOE Office of Civilian Radioactive Waste Management (RW) formed the Waste Acceptance Committee (WAC). The WAC included representatives from the candidate repository sites, the waste producing sites and DOE. The WAC was responsible for developing the Waste Acceptance Preliminary Specifications (WAPS) which defined the requirements the waste forms must meet to be compatible with the candidate repository geologies

Alternative methods of salt disposal at the seven salt sites for a nuclear waste repository

International Nuclear Information System (INIS)

1987-02-01

This study discusses the various alternative salt management techniques for the disposal of excess mined salt at seven potentially acceptable nuclear waste repository sites: Deaf Smith and Swisher Counties, Texas; Richton and Cypress Creek Domes, Mississippi; Vacherie Dome, Louisiana; and Davis and Lavender Canyons, Utah. Because the repository development involves the underground excavation of corridors and waste emplacement rooms, in either bedded or domed salt formations, excess salt will be mined and must be disposed of offsite. The salt disposal alternatives examined for all the sites include commercial use, ocean disposal, deep well injection, landfill disposal, and underground mine disposal. These alternatives (and other site-specific disposal methods) are reviewed, using estimated amounts of excavated, backfilled, and excess salt. Methods of transporting the excess salt are discussed, along with possible impacts of each disposal method and potential regulatory requirements. A preferred method of disposal is recommended for each potentially acceptable repository site. 14 refs., 5 tabs

Civil engineering challenge with nuclear waste

International Nuclear Information System (INIS)

Day, D.

1985-01-01

The civil engineer can help to solve the problems in disposing of nuclear waste in a deep geologic formation. The site for a nuclear waste repository must be carefully selected so that the geology provides the natural barrier between the waste and the accessible environment specified by the NRC and the EPA. This engineer is familiar with the needed structure and conditions of the host and surrounding rocks, and also the hydraulic mechanisms for limiting the migration of water in the rocks. To dispose of the nuclear waste underground requires stable and long-lasting shafts and tunnels such as civil engineers have designed and constructed for many other uses. The planning, design and construction of the ground surface facilities for a nuclear waste repository involves civil engineering in many ways. The transporation of heavy, metal shielded casks requires special attention to the system of highways and railroads accessing the repository. Structures for handling the shipping casks and transferring the waste onsite and into the deep geologic formation need special considerations. The structures must provide the NRC required containment, including hot cells for remote handling. Therefore, structural design strives for buildings, ventilation structures, shaft headframes, etc., to be earthquake and tornado-proof. These important design bases and considerations for the civil engineer working on a nuclear waste repository are discussed in this paper

Deep geological isolation of nuclear waste: numerical modeling of repository scale hydrology

International Nuclear Information System (INIS)

Dettinger, M.D.

1980-04-01

The Scope of Work undertaken covers three main tasks, described as follows: (Task 1) CDM provided consulting services to the University on modeling aspects of the study having to do with transport processes involving the local groundwater system near the repository and the flow of fluids and vapors through the various porous media making up the repository system. (Task 2) CDM reviewed literature related to repository design, concentrating on effects of the repository geometry, location and other design factors on the flow of fluids within the repository boundaries, drainage from the repository structure, and the eventual transport of radionucldies away from the repository site. (Task 3) CDM, in a joint effort with LLL personnel, identified generic boundary and initial conditions, identified processes to be modeled, and recommended a modeling approach with suggestions for appropriate simplifications and approximations to the problem and identifiying important parameters necessary to model the processes. This report consists of two chapters and an appendix. The first chapter (Chapter III of the LLL report) presents a detailed description and discussion of the modeling approach developed in this project, its merits and weaknesses, and a brief review of the difficulties anticipated in implementing the approach. The second chapter (Chapter IV of the LLL report) presents a summary of a survey of researchers in the field of repository performance analysis and a discussion of that survey in light of the proposed modeling approach. The appendix is a review of the important physical processes involved in the potential hydrologic transport of radionuclides through, around and away from deep geologic nuclear waste repositories

BIODOSE: a code for predicting the dose to man from radionuclides released from underground nuclear waste repositories

International Nuclear Information System (INIS)

Bonner, N.A.; Ng, Y.C.

1980-03-01

The BIODOSE computer program simulates the environmental transport of radionuclides released to surface water and predicts the resulting dosage to humans. This report describes the program and discusses its use in the evaluation of nuclear waste repositories. The methods used to estimate dose are examined critically, and the most important parameters in each stage of the calculations are identified as an aid in planning for measurements in the field. Dose predictions from releases of nuclear waste to a large northwestern river (the baseline river) are presented to point out the nuclides, compartments and pathways that contribute most to the hazard as a function of waste storage time. Predictions for five other water systems are presented to identify the most important system parameters that determine the concentrations of individual nuclides in compartments and the resultant dose. The uncertainties in the biological parameters for dose prediction are identified, and changes in current values are suggested. Various ways of reporting dose estimates for radiological safety assessments are discussed. Additional work needed to improve the dose predictions from BIODOSE and specific areas and steps to improve our capabilities to assess the environmental transport of nuclides released from nuclear waste repositories and the resultant dose to man are suggested

Tergiversating the price of nuclear waste storage

International Nuclear Information System (INIS)

Mills, R.L.

1984-01-01

Tergiversation, the evasion of straightforward action of clearcut statement of position, was a characteristic of high-level nuclear waste disposal until the US Congress passed the Nuclear Waste Policy Act of 1982. How the price of waste storage is administered will affect the design requirements of monitored retrievable storage (MRS) facilities as well as repositories. Those decisions, in part, are internal to the Department of Energy. From the utility's viewpoint, the options are few but clearer. Reprocessing, as performed in Europe, is not a perfect substitute for MRS. The European reprocess-repository sequence will not yield the same nuclear resource base as the American MRS-repository scheme. For the future price of the energy resource represented by nuclear waste, the author notes that tergiversation continues. 3 references

Preliminary post-closure safety assessment of repository concepts for low level radioactive waste at the Bruce Site, Ontario

International Nuclear Information System (INIS)

Little, R.H.; Penfold, J.S.S.; Egan, M.J.; Leung, H.

2005-01-01

The preliminary post-closure safety assessment of permanent repository concepts for low-level radioactive waste (LLW) at the Ontario Power Generation (OPG) Bruce Site is described. The study considered the disposal of both short and long-lived LLW. Four geotechnically feasible repository concepts were considered (two near-surface and two deep repositories). An approach consistent with best international practice was used to provide a reasoned and comprehensive analysis of post-closure impacts of the repository concepts. The results demonstrated that the deep repository concepts in shale and in limestone, and the surface repository concept on sand should meet radiological protection criteria. For the surface repository concept on glacial till, it appears that increased engineering such as grouting of waste and voids should be considered to meet the relevant dose constraint. Should the project to develop a permanent repository for LLW proceed, it is expected that this preliminary safety assessment would need to be updated to take account of future site-specific investigations and design updates. (author)

Third report, development of site suitability and design performance data base for a high level nuclear waste repository

International Nuclear Information System (INIS)

1978-05-01

This report presents the results of mining and geotechnical studies provided as support for the development of a technical data base suitable for the generation of a regulatory framework governing high-level nuclear waste disposal: flow path models for basalts, salt domes, and crystalline rocks; simplistic model evaluations; loss of administrative control; repository conceptual designs; repository design considerations; and design performance criteria

DECOVALEX III PROJECT. Mathematical Models of Coupled Thermal-Hydro-Mechanical Processes for Nuclear Waste Repositories. Executive Summary

Energy Technology Data Exchange (ETDEWEB)

Jing, L.; Stephansson, O. [Royal Inst. of Technology, Stockholm (Sweden). Engineering Geology; Tsang, C.F. [Lawrence Berkely National Laboratory, Berkeley, CA (United States). Earth Science Div.; Mayor, J.C. [ENRESA, Madrid (Spain); Kautzky, F. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)] (eds.)

2005-02-15

DECOVALEX is an international consortium of governmental agencies associated with the disposal of high-level nuclear waste in a number of countries. The consortium's mission is the DEvelopment of COupled models and their VALidation against EXperiments. Hence the acronym/name DECOVALEX. Currently, agencies from Canada, Finland, France, Germany, Japan, Spain, Switzerland, Sweden, United Kingdom, and the United States are in DECOVALEX. Emplacement of nuclear waste in a repository in geologic media causes a number of physical processes to be intensified in the surrounding rock mass due to the decay heat from the waste. The four main processes of concern are thermal, hydrological, mechanical and chemical. Interactions or coupling between these heat-driven processes must be taken into account in modeling the performance of the repository for such modeling to be meaningful and reliable. DECOVALEX III is organized around four tasks. The FEBEX (Full-scale Engineered Barriers EXperiment) in situ experiment being conducted at the Grimsel site in Switzerland is to be simulated and analyzed in Task 1. Task 2, centered around the Drift Scale Test (DST) at Yucca Mountain in Nevada, USA, has several sub-tasks (Task 2A, Task 2B, Task 2C and Task 2D) to investigate a number of the coupled processes in the DST. Task 3 studies three benchmark problems: a) the effects of thermal-hydrologic-mechanical (THM) coupling on the performance of the near-field of a nuclear waste repository (BMT1); b) the effect of upscaling THM processes on the results of performance assessment (BMT2); and c) the effect of glaciation on rock mass behavior (BMT3). Task 4 is on the direct application of THM coupled process modeling in the performance assessment of nuclear waste repositories in geologic media. This executive summary presents the motivation, structure, objectives, approaches, and the highlights of the main achievements and outstanding issues of the tasks studied in the DECOVALEX III project

DECOVALEX III PROJECT. Mathematical Models of Coupled Thermal-Hydro-Mechanical Processes for Nuclear Waste Repositories. Executive Summary

International Nuclear Information System (INIS)

Jing, L.; Stephansson, O.; Kautzky, F.

2005-02-01

DECOVALEX is an international consortium of governmental agencies associated with the disposal of high-level nuclear waste in a number of countries. The consortium's mission is the DEvelopment of COupled models and their VALidation against EXperiments. Hence the acronym/name DECOVALEX. Currently, agencies from Canada, Finland, France, Germany, Japan, Spain, Switzerland, Sweden, United Kingdom, and the United States are in DECOVALEX. Emplacement of nuclear waste in a repository in geologic media causes a number of physical processes to be intensified in the surrounding rock mass due to the decay heat from the waste. The four main processes of concern are thermal, hydrological, mechanical and chemical. Interactions or coupling between these heat-driven processes must be taken into account in modeling the performance of the repository for such modeling to be meaningful and reliable. DECOVALEX III is organized around four tasks. The FEBEX (Full-scale Engineered Barriers EXperiment) in situ experiment being conducted at the Grimsel site in Switzerland is to be simulated and analyzed in Task 1. Task 2, centered around the Drift Scale Test (DST) at Yucca Mountain in Nevada, USA, has several sub-tasks (Task 2A, Task 2B, Task 2C and Task 2D) to investigate a number of the coupled processes in the DST. Task 3 studies three benchmark problems: a) the effects of thermal-hydrologic-mechanical (THM) coupling on the performance of the near-field of a nuclear waste repository (BMT1); b) the effect of upscaling THM processes on the results of performance assessment (BMT2); and c) the effect of glaciation on rock mass behavior (BMT3). Task 4 is on the direct application of THM coupled process modeling in the performance assessment of nuclear waste repositories in geologic media. This executive summary presents the motivation, structure, objectives, approaches, and the highlights of the main achievements and outstanding issues of the tasks studied in the DECOVALEX III project. The

A literature review of coupled thermal-hydrologic-mechanical-chemical processes pertinent to the proposed high-level nuclear waste repository at Yucca Mountain

International Nuclear Information System (INIS)

Manteufel, R.D.; Ahola, M.P.; Turner, D.R.; Chowdhury, A.H.

1993-07-01

A literature review has been conducted to determine the state of knowledge available in the modeling of coupled thermal (T), hydrologic (H), mechanical (M), and chemical (C) processes relevant to the design and/or performance of the proposed high-level waste (HLW) repository at Yucca Mountain, Nevada. The review focuses on identifying coupling mechanisms between individual processes and assessing their importance (i.e., if the coupling is either important, potentially important, or negligible). The significance of considering THMC-coupled processes lies in whether or not the processes impact the design and/or performance objectives of the repository. A review, such as reported here, is useful in identifying which coupled effects will be important, hence which coupled effects will need to be investigated by the US Nuclear Regulatory Commission in order to assess the assumptions, data, analyses, and conclusions in the design and performance assessment of a geologic reposit''. Although this work stems from regulatory interest in the design of the geologic repository, it should be emphasized that the repository design implicitly considers all of the repository performance objectives, including those associated with the time after permanent closure. The scope of this review is considered beyond previous assessments in that it attempts with the current state-of-knowledge) to determine which couplings are important, and identify which computer codes are currently available to model coupled processes

A literature review of coupled thermal-hydrologic-mechanical-chemical processes pertinent to the proposed high-level nuclear waste repository at Yucca Mountain

Energy Technology Data Exchange (ETDEWEB)

Manteufel, R.D.; Ahola, M.P.; Turner, D.R.; Chowdhury, A.H. [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

1993-07-01

A literature review has been conducted to determine the state of knowledge available in the modeling of coupled thermal (T), hydrologic (H), mechanical (M), and chemical (C) processes relevant to the design and/or performance of the proposed high-level waste (HLW) repository at Yucca Mountain, Nevada. The review focuses on identifying coupling mechanisms between individual processes and assessing their importance (i.e., if the coupling is either important, potentially important, or negligible). The significance of considering THMC-coupled processes lies in whether or not the processes impact the design and/or performance objectives of the repository. A review, such as reported here, is useful in identifying which coupled effects will be important, hence which coupled effects will need to be investigated by the US Nuclear Regulatory Commission in order to assess the assumptions, data, analyses, and conclusions in the design and performance assessment of a geologic reposit``. Although this work stems from regulatory interest in the design of the geologic repository, it should be emphasized that the repository design implicitly considers all of the repository performance objectives, including those associated with the time after permanent closure. The scope of this review is considered beyond previous assessments in that it attempts with the current state-of-knowledge) to determine which couplings are important, and identify which computer codes are currently available to model coupled processes.

Evolution of waste-package design at the potential U.S. geologic repository

International Nuclear Information System (INIS)

Benton, H.; Harkins, B.

2000-01-01

This paper describes the evolution of the waste-package design at the potential geologic repository for spent nuclear fuel and high-level waste at Yucca Mountain in Nevada. Because the potential repository is the first of its kind, the design of its components must be flexible and capable of evolving in response to continuing scientific study, development efforts, and changes to performance criteria. The team of scientists and engineers at the Yucca Mountain Project has utilized a systematic, scientific approach to design the potential geologic nuclear-waste repository. As a result of continuing development efforts, the design has incorporated a growing base of scientific and engineering information to ensure that regulatory and performance requirements are met. (authors)

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 1

International Nuclear Information System (INIS)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packing, and other surface facility operations are described. Operations in the shafts underground are described, including waste hoisting, transfer, and vertical emplacement. This report specifically addresses the vertical emplacement mode, the reference design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 1

Energy Technology Data Exchange (ETDEWEB)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packing, and other surface facility operations are described. Operations in the shafts underground are described, including waste hoisting, transfer, and vertical emplacement. This report specifically addresses the vertical emplacement mode, the reference design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs.

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, horizontal emplacment mode: Volume 1

International Nuclear Information System (INIS)

1987-12-01

This Conceptual Design Report describes the conceptual design of a high-level nuclear waste repository in salt at a proposed site in Deaf Smith County, Texas. Waste receipt, processing, packaging, and other surface facility operations are described. Operations in the shafts and underground are described, including waste hoisting, transfer, and horizontal emplacement. This report specifically addresses the horizontal emplacement mode, the passive alternate design for the repository. Waste retrieval capability is described. The report includes a description of the layout of the surface, shafts, and underground. Major equipment items are identified. The report includes plans for decommissioning and sealing of the facility. The report discusses how the repository will satisfy performance objectives. Chapters are included on basis for design, design analyses, and data requirements for completion of future design efforts. 105 figs., 52 tabs

A Careful Blasting Technique During Construction of underground Openings for Nuclear Waste Repository

International Nuclear Information System (INIS)

Ester, Z.; Vrkljan, D.

1998-01-01

Underground nuclear waste repositories are constructed in natural rock formations, with heterogenous compound and structure, and should be accommodated in design and construction according to rock conditions. The quality insurance of underground repository, during and after construction, is most demanding in view of contour and category of excavation. the technology of drilling and blasting, regarding the mechanical excavation, is accommodated in sense of response to cross section magnitude of underground openings, the rock conditions and category, the support performance and other design demands. The high level rock damage around underground openings, that is in opposition with reaching quality insurance. Conventional construction technology can be successful by implementation of controlled blasting technique avoiding extensive rock weakness. (author)

Computer enhanced release scenario analysis for a nuclear waste repository

International Nuclear Information System (INIS)

Stottlemyre, J.A.; Petrie, G.M.; Mullen, M.F.

1979-01-01

An interactive (user-oriented) computer tool is being developed at PNL to assist in the analysis of release scenarios for long-term safety assessment of a continental geologic nuclear waste repository. Emphasis is on characterizing the various ways the geologic and hydrologic system surrounding a repository might vary over the 10 6 to 10 7 years subsequent to final closure of the cavern. The potential disruptive phenomena are categorized as natural geologic and man-caused and tend to be synergistic in nature. The computer tool is designed to permit simulation of the system response as a function of the ongoing disruptive phenomena and time. It is designed to be operated in a determinatic manner, i.e., user selection of the desired scenarios and associated rate, magnitude, and lag time data; or in a stochastic mode. The stochastic mode involves establishing distributions for individual phenomena occurrence probabilities, rates, magnitudes, and phase relationships. A Monte-Carlo technique is then employed to generate a multitude of disruptive event scenarios, scan for breaches of the repository isolation, and develop input to the release consequence analysis task. To date, only a simplified one-dimensional version of the code has been completed. Significant modification and development is required to expand its dimensionality and apply the tool to any specific site

Reinforced concrete in the intermediable-level nuclear waste repository

International Nuclear Information System (INIS)

Duffo, Gustavo

2009-01-01

The National Atomic Energy Commission (CNEA) is responsible for developing the nuclear waste disposal management programme. This programme contemplates the design and construction of a facility for the final disposal of intermediate-level radioactive wastes. The proposed model is a near-surface monolithic repository similar to those in operation in El Cabril, Spain. The design of this type of repository is based on the use of multiple, independent and redundant barriers and the model foresees a period of 300 years of institutional post-closure control. Since the vault and cover are major components of the engineered barriers, the durability of these concrete structures is an important aspect for the facility integrity. This work presents laboratory investigations performed on the corrosion susceptibility of steel rebars embedded in two different types of high performance reinforced concretes, recently developed by the National Institute of Industrial Technology (Argentine). Concretes were made with cement with Blast Furnace Slag (CAH) and Silica Fume cement (CAH + SF). The aim of this work is to predict the service life of the intermediate level radioactive waste disposal vaults from data obtained from electrochemical techniques. Besides, the diffusion coefficients of aggressive species, such as chloride and carbon dioxide, were also determined. On the other hand, data obtained with corrosion sensors embedded in a vault prototype is also included. These sensors allow on-line measurements of several parameters related to the corrosion process such as rebar corrosion potential and corrosion current density; incoming oxygen flow that reaches the metal surface; concrete electrical resistivity; chloride concentration and internal concrete temperature. All the information obtained from both, laboratory tests and sensors will be used for the final design of the container in order to achieve a service life more or equal than the foreseen durability for this type of

Social impacts of hazardous and nuclear facilities and events: Implications for Nevada and the Yucca Mountain high-level nuclear waste repository

International Nuclear Information System (INIS)

Freudenburg, W.R.; Carter, L.F.; Willard, W.; Lodwick, D.G.; Hardert, R.A.; Levine, A.G.; Couch, S.R.; Edelstein, M.R.

1992-05-01

Social impacts of a nuclear waste repository are described. Various case studies are cited such as Rocky Flats Plant, the Feed Materials Production Center, and Love Canal. The social impacts of toxic contamination, mitigating environmental stigma and loss of trust are also discussed

Deep repositories for waste central to uranium debate

International Nuclear Information System (INIS)

Kannegieter, T.

1991-01-01

While no deep repositories for high level wastes (HLW) have yet been constructed it is shown that technology to safely entomb the wastes for tens of thousands of years already exists. The borosilicate glass (vitrification) developed in France has been accepted by all countries who are reprocessing. Meanwhile, the Australian Synroc has not yet been put into service. Synroc developers at the Australian Nuclear Science and Technology Organization believe it will be the second generation waste form. The advantages and disadvantages of both technologies are briefly discussed as well as some of the regulatory, political, legal and technical conflicts surrounding the issue of HLW repositories. 1 tab., ills

Effect of boundary conditions on thermohydraulic behavior of clay buffer used in nuclear waste repository

International Nuclear Information System (INIS)

Arul Peter, A.; Murugesan, K.; Mamidi, Ganesh; Sharma, Umesh Kumar; Sharma, D. Akanshu; Arora, Puneet

2010-01-01

The use of nuclear energy is increasing dramatically in the world due to the fast depletion of fossil fuels, and hence the nuclear waste disposal and its short and long-term effects are of considerable importance. One of the options considered for nuclear waste disposal is underground nuclear waste repository facility. In this underground nuclear waste disposal system the waste filled canisters are placed in the rock surrounded by an engineered clay barrier and the whole system is buried in the geological formation, which serves as the natural or geological barrier. The important characteristic of the clay barrier is that it should not open up for radiation though it is continuously subjected to heat loading from the canisters. The heat and moisture transport mechanisms through the clay barrier plays an important role in deciding its mechanical strength. Clay behaves as an unsaturated porous material when it is used as a buffer material in nuclear waste facility. The governing equations for heat and moisture transfer through unsaturated porous media are coupled and nonlinear and hence they have to be solved using numerical solution technique. This paper reports the results of a numerical study on heat and moisture transport through a buffer layer made of clay as used in nuclear waste repository. Galerkin's weighted residual finite element method has been employed for the solution of the non-linear coupled governing equations used to represent the heat and moisture transport through unsaturated clay material. A detailed computational procedure has been established for the solution of the non-linear governing equations using Newton-Raphson technique. Initially the code has been validated with available experimental results. Then numerical simulation results were obtained for heat and moisture variations within the buffer material for Dirichlet temperature boundary conditions in the range, 50 deg C 2 2 , with an aim to simulate the boundary conditions which the clay

Peer review for high-level nuclear waste repositories: Generic technical position

International Nuclear Information System (INIS)

Altman, W.D.; Donnelly, J.P.; Kennedy, J.E.

1988-02-01

This document provides guidance on the use of the peer review process in the high-level nuclear waste repository program. The applicant must demonstrate in the license application that the applicable health, safety, and environmental regulations in 10 CFR Part 60 have been met. Confidence in the data used to support the license application is obtained through a quality assurance (AQ) program. Peer reviews may be used as part of the QA actions necessary to provide adequate confidence in the work being reviewed. Because of several unique conditions inherent to the geologic repository program, expert judgment will need to be utilized in assessing the adequacy of work. Peer reviews are a mechanism by which these judgments may be made. This document provides guidance on areas where a peer review is appropriate, the acceptability of peers, and the conduct and documentation of a peer review

Seismic design of low-level nuclear waste repositories and toxic waste management facilities

International Nuclear Information System (INIS)

Chung, D.H.; Bernreuter, D.L.

1984-01-01

Identification of the elements of typical hazardous waste facilities (HFWs) that are the major contributors to the risk are focussed on as the elements which require additional considerations in the design and construction of low-level nuclear waste management repositories and HWFs. From a recent study of six typical HWFs it was determined that the factors that contribute most to the human and environmental risk fall into four basic categories: geologic and seismological conditions at each HWF; engineered structures at each HWF; environmental conditions at each HWF; and nature of the material being released. In selecting and carrying out the six case studies, three groups of hazardous waste facilities were examined: generator industries which treat or temporarily store their own wastes; generator facilities which dispose of their own hazardous wastes on site; and industries in the waste treatment and disposal business. The case studies have a diversity of geologic setting, nearby settlement patterns, and environments. Two sites are above a regional aquifer, two are near a bay important to regional fishing, one is in rural hills, and one is in a desert, although not isolated from nearby towns and a groundwater/surface-water system. From the results developed in the study, it was concluded that the effect of seismic activity on hazardous facilities poses a significant risk to the population. Fifteen reasons are given for this conclusion

Nuclear waste

International Nuclear Information System (INIS)

Anon.

1996-01-01

The NEA Nuclear Waste Bulletin has been prepared by the Radiation Protection and Waste Management Division of the OECD Nuclear Energy Agency to provide a means of communication amongst the various technical and policy groups within the waste management community. In particular, it is intended to provide timely and concise information on radioactive waste management activities, policies and programmes in Member countries and at the NEA. It is also intended that the Bulletin assists in the communication of recent developments in a variety of areas contributing to the development of acceptable technology for the management and disposal of nuclear waste (e.g., performance assessment, in-situ investigations, repository engineering, scientific data bases, regulatory developments, etc)

Role of mine ventilation in site selection for a nuclear waste repository

International Nuclear Information System (INIS)

McPherson, M.J.

1984-01-01

The application of mine ventilation practice and theory to the measurement of groundwater flow for the purpose of the selection of sites for underground storage of nuclear spent fuel is described. The discipline of mine ventilation has an important part to play not only in the design and operation of an underground nuclear waste repository but also during the early stages of potential site characterization. One of the most vital factors in the selection of a suitable site is the rate at which groundwater can flow through the native rock. The effects of repository heat on groundwater migration are highlighted and a description of a major experiment in an underground test site is included. Detailed monitoring of airflow and its psychrometric properties enabled quantification of very low rates of water seepage into an isolated heading. The results indicated the relationship between permeability of a fractured rock and temperature. The transient phenomena that govern evaporation of water from fissured rock surfaces in the test chamber are also examined. (author)

A Rock Mechanics and Coupled Hydro mechanical Analysis of Geological Repository of High Level Nuclear Waste in Fractured Rocks

International Nuclear Information System (INIS)

Min, Kibok

2011-01-01

This paper introduces a few case studies on fractured hard rock based on geological data from Sweden, Korea is one of a few countries where crystalline rock is the most promising rock formation as a candidate site of geological repository of high level nuclear waste. Despite the progress made in the area of rock mechanics and coupled hydro mechanics, extensive site specific study on multiple candidate sites is essential in order to choose the optimal site. For many countries concerned about the safe isolation of nuclear wastes from the biosphere, disposal in a deep geological formation is considered an attractive option. In geological repository, thermal loading continuously disturbs the repository system in addition to disturbances a recent development in rock mechanics and coupled hydro mechanical study using DFN(Discrete Fracture Network) - DEM(Discrete Element Method) approach mainly applied in hard, crystalline rock containing numerous fracture which are main sources of deformation and groundwater flow

Nuclear Waste State of the Art Report 2010 - challenges for the final repository programme

International Nuclear Information System (INIS)

2010-01-01

In this year's report the Council calls for that SKB makes more studies of how the copper corrosion affects the long-term safety. SKB is criticized for not sufficiently set clear requirements for the bentonite clay, which should surround the copper canisters. Internationally possibility to take back spent fuel from the repository is one highly topical issue. Retrieval of waste for transmutation and future reuse of spent nuclear fuel should be discussed also in Sweden. It is estimated that SKB submit an application within one year to dispose of spent nuclear fuel in the 500 meter deep repository in the bedrock at Oesthammar. The mountain is the natural barrier between the nuclear fuel and the environment, and in addition to this, spent fuel is surrounded by two technical barriers: copper canisters and bentonite clay. The corrosion resistance of the copper canisters has recently been challenged by research from the Royal Institute of Technology, and this has created uncertainty over copper canister as a suitable barrier. The Council believes that SKB should actively contribute to investigate the issue of corrosion of copper in pure, oxygen-free water in a scientifically unassailable way, and that its potential effect is determined. Bentonite clay is the subject of intensive development work in SKB's new bentonite-laboratory, but the Council believes that SKB must set clearer requirements for bentonite clay quality, particularly with regard to thresholds for the contaminants that may occur. The question of what is possible and desirable in order retrieve the spent fuel from the repository is international discussed. Retrievability before closure is part of the safety requirements and is not controversial. Retrievability after sealing on the other hand, is both a controversial and complex issue, especially from a civil law perspective. New technology can make high-level waste as an interesting energy source, or use of the Partitioning and Transmutation can make the

Thermal analyses for a nuclear-waste repository in tuff using USW-G1 borehole data

International Nuclear Information System (INIS)

Johnson, R.L.

1982-10-01

Thermal calculations using properties of tuffs obtained from the USW-G1 borehole, located near the SW margin of the Nevada Test Site (NTS), have been completed for a nuclear waste repository sited in welded tuff below the water table. The analyses considered two wasteforms, high level waste and spent fuel, emplaced at two different, gross thermal loadings, 50 and 75 kW/Acre (20.24 and 30.36 kW/ha). Calculations were made assuming that no boiling of the groundwater occurs; i.e., that the hydrostatic head potential was reestablished soon after waste emplacement. 23 figures, 2 tables

Future Shock in Nuclear Waste Disposal

Energy Technology Data Exchange (ETDEWEB)

Frishman, Steve [Nevada Agency for Nuclear Projects, Carson City, NV (United States)

2006-09-15

The United States Environmental Protection Agency (EPA) astonished many in the high-level nuclear waste management community when it proposed, in August 2005, new Public Health and Environmental Radiation Protection Standards for Yucca Mountain, Nevada. The new standards set a compliance period of one million years for a Yucca Mountain high-level nuclear waste repository. The first 10,000 years after repository closure would be governed by a health-based individual dose limit of 15 millirems per year (0.15 mSv/year), with the remaining time period subject to a background-based individual dose limit of 350 millirems per year (3.5 mSv/year). EPA's proposed standards for a Yucca Mountain nuclear waste repository represent an astonishing break with principles embedded in regulatory policies for protection of the public from radiation effects imposed by activities such as generation of electricity from nuclear power reactors and storage and disposal of radioactive wastes.

For Sale: Nuclear Waste Sites--Anyone Buying?

Science.gov (United States)

Hancock, Don

1992-01-01

Explores why the United States Nuclear Waste Program has been unable to find a volunteer state to host either a nuclear waste repository or monitored retrieval storage facility. Discusses the Department of Energy's plans for Nevada's Yucca Mountain as a repository and state and tribal responses to the plan. (21 references) (MCO)

Creep in crystalline rock with application to high level nuclear waste repository

International Nuclear Information System (INIS)

Eloranta, P.; Simonen, A.

1992-06-01

The time-dependent strength and deformation properties of hard crystalline rock are studied. Theoretical models defining the phenomena which can effect these properties are reviewed. The time- dependent deformation of the openings in the proposed nuclear waste repository is analysed. The most important factors affecting the subcritical crack growth in crystalline rock are the stress state, the chemical environment, temperature and microstructure of the rock. There are several theoretical models for the analysis of creep and cyclic fatigue: deformation diagrams, rheological models thermodynamic models, reaction rate models, stochastic models, damage models and time-dependent safety factor model. They are defective in describing the three-axial stress condition and strength criteria. In addition, the required parameters are often too difficult to determine with adequate accuracy. Therefore these models are seldom applied in practice. The effect of microcrack- driven creep on the stability of the work shaft, the emplacement tunnel and the capsulation hole of a proposed nuclear waste repository was studied using a numerical model developed by Atomic Energy of Canada Ltd. According to the model, the microcrack driven creep progresses very slowly in good quality rock. Poor rock quality may accelerate the creep rate. The model is very sensitive to the properties of the rock and secondary stress state. The results show that creep causes no stability problems on excavations in good rock. The results overestimate the effect of the creep, because the analysis omitted the effect of support structures and backfilling

Applying system engineering methods to site characterization research for nuclear waste repositories

International Nuclear Information System (INIS)

Woods, T.W.

1985-01-01

Nuclear research and engineering projects can benefit from the use of system engineering methods. This paper is brief overview illustrating how system engineering methods could be applied in structuring a site characterization effort for a candidate nuclear waste repository. System engineering is simply an orderly process that has been widely used to transform a recognized need into a fully defined system. Such a system may be physical or abstract, natural or man-made, hardware or procedural, as is appropriate to the system's need or objective. It is a way of mentally visualizing all the constituent elements and their relationships necessary to fulfill a need, and doing so compliant with all constraining requirements attendant to that need. Such a system approach provides completeness, order, clarity, and direction. Admittedly, system engineering can be burdensome and inappropriate for those project objectives having simple and familiar solutions that are easily held and controlled mentally. However, some type of documented and structured approach is needed for those objectives that dictate extensive, unique, or complex programs, and/or creation of state-of-the-art machines and facilities. System engineering methods have been used extensively and successfully in these cases. The scientific methods has served well in ordering countless technical undertakings that address a specific question. Similarly, conventional construction and engineering job methods will continue to be quite adequate to organize routine building projects. Nuclear waste repository site characterization projects involve multiple complex research questions and regulatory requirements that interface with each other and with advanced engineering and subsurface construction techniques. There is little doubt that system engineering is an appropriate orchestrating process to structure such diverse elements into a cohesive, well defied project

Methodology Used for Total System Performance Assessment of the Potential Nuclear Waste Repository at Yucca Mountain (USA)

International Nuclear Information System (INIS)

E. Devibec; S.D. Sevougian; P.D. Mattie; J.A. McNeish; S. Mishra

2001-01-01

The U.S. Department of Energy and its contractors are currently evaluating a site in Nevada (Yucca Mountain) for disposal of high-level radioactive waste from U.S. commercial nuclear plants and U.S. government-owned facilities. The suitability of the potential geologic repository is assessed, based on its performance in isolating the nuclear waste from the environment. Experimental data and models representing the natural and engineered barriers are combined into a Total System Performance Assessment (TSPA) model [1]. Process models included in the TSPA model are unsaturated zone flow and transport, thermal hydrology, in-drift geochemistry, waste package degradation, waste form degradation, engineered barrier system transport, saturated zone flow and transport, and biosphere transport. Because of the uncertainty in the current data and in the future evolution of the total system, simulations follow a probabilistic approach. Multiple realization simulations using Monte Carlo analysis are conducted over time periods of up to one million years, which estimates a range of possible behaviors of the repository. The environmental impact is measured primarily by the annual dose received by an average member of a critical population group residing 20 km down-gradient of the potential repository. In addition to the nominal scenario, other exposure scenarios include the possibility of disruptive events such as volcanic eruption or intrusion, or accidental human intrusion. Sensitivity to key uncertain processes is analyzed. The influence of stochastic variables on the TSPA model output is assessed by ''uncertainty importance analysis'', e.g., regression analysis and classification tree analysis. Further investigation of the impact of parameters and assumptions is conducted through ''one-off analysis'', which consists in fixing a parameter at a particular value, using an alternative conceptual model, or in making a different assumption. Finally, robustness analysis evaluates

Radioactive waste isolation in salt: special advisory report on the status of the Office of Nuclear Waste Isolation's plans for repository performance assessment

International Nuclear Information System (INIS)

Ditmars, J.D.; Walbridge, E.W.; Rote, D.M.; Harrison, W.; Herzenberg, C.L.

1983-10-01

Repository performance assessment is analysis that identifies events and processes that might affect a repository system for isolation of radioactive waste, examines their effects on barriers to waste migration, and estimates the probabilities of their occurrence and their consequences. In 1983 Battelle Memorial Institute's Office of Nuclear Waste Isolation (ONWI) prepared two plans - one for performance assessment for a waste repository in salt and one for verification and validation of performance assessment technology. At the request of the US Department of Energy's Salt Repository Project Office (SRPO), Argonne National Laboratory reviewed those plans and prepared this report to advise SRPO of specific areas where ONWI's plans for performance assessment might be improved. This report presents a framework for repository performance assessment that clearly identifies the relationships among the disposal problems, the processes underlying the problems, the tools for assessment (computer codes), and the data. In particular, the relationships among important processes and 26 model codes available to ONWI are indicated. A common suggestion for computer code verification and validation is the need for specific and unambiguous documentation of the results of performance assessment activities. A major portion of this report consists of status summaries of 27 model codes indicated as potentially useful by ONWI. The code summaries focus on three main areas: (1) the code's purpose, capabilities, and limitations; (2) status of the elements of documentation and review essential for code verification and validation; and (3) proposed application of the code for performance assessment of salt repository systems. 15 references, 6 figures, 4 tables

Multi criteria decision analysis on a waste repository in Mol

International Nuclear Information System (INIS)

Carle, B.

2005-01-01

In Belgium, the management of radioactive waste is taken care of by ONDRAF/NIRAS, the Belgian Agency for Radioactive Waste and Enriched Fissile Materials. Local partnerships with stakeholders from municipalities in existing nuclear zones were setup to facilitate the dialogue between the repository designers and the local community. Since the establishment of the partnership in Mol, MONA in February 2000, all aspects of a possible near-surface or a deep geological repository are discussed in 4 working groups by around 50 volunteer members. The outcome of the discussions in the partnership can be a shared project, supported by both local stakeholders and ONDRAF/NIRAS, in which the specifications and the conditions needed for establishing a repository in Mol are elaborated. MONA asked the Decision Strategy Research Department of SCK-CEN to organise a Multi Criteria Analysis (MCA) in the context of the deciding between a surface and a deep repository for low level radioactive waste. The objective of the multi criteria analysis is to support a number of representatives of the various working groups within MONA in their selection between two acceptable options for a repository of low level radioactive waste on the territory of Mol. The options are the surface repository developed by the working groups of MONA, and a deep repository in the clay layers underneath the nuclear site of Mol. This study should facilitate the selection between both options, or in case this appears to be difficult, at least to get a well-structured overview of all factors (criteria) of importance to the judgement, and to get insight into the degree in which the various criteria contribute to the selection

Preliminary analysis of the cost and risk of transporting nuclear waste to potential candidate commercial repository sites

International Nuclear Information System (INIS)

Wilmot, E.L.; Madsen, M.M.; Cashwell, J.W.; Joy, D.S.

1983-06-01

This report documents preliminary cost and risk analyses that were performed in support of the Nuclear Waste Terminal Storage (NWTS) program. The analyses compare the costs and hazards of transporting wastes to each of five regions that contain potential candidate nuclear waste repository sites being considered by the NWTS program. These regions are: the Gulf Interior Region, the Permian Basin, the Paradox Basin, Yucca Mountain, and Hanford. Two fuel-cycle scenarios were analyzed: once-through and reprocessing. Transportation was assumed to be either entirely by truck or entirely by rail for each of the scenarios. The results from the risk analyses include those attributable to nonradiological causes and those attributable to the radioactive character of the wastes being transported. 17 references

United States regulations for institutional controls at high-level waste repositories

International Nuclear Information System (INIS)

Piccone, Josephine

2015-01-01

The United States regulations for disposal of spent nuclear fuel and high-level radioactive waste are found at Title 10 of the Code of Federal Regulations (10 CFR) Parts 60 and 63, which cover deep geologic disposal at a generic site and at Yucca Mountain, Nevada, respectively. As an independent regulator, the US Nuclear Regulatory Commission (NRC) is responsible for licensing and oversight of a high-level waste repository in the United States. The licensing approach for disposal has discreet decisions, made by the NRC, that include approval of construction authorisation, approval to receive and possess high-level radioactive waste, and approval for permanent closure. For construction authorisation approval, the applicant must provide a description of the programme to be used to maintain the records. The NRC will have an active oversight role during the construction and operation period, which can be on the order of 100 years for the facility before permanent closure. The oversight activities are part of the active institutional controls, and serve as a means of conveying knowledge for that initial period, given that this will likely involve multiple generations of workers for both the implementer and the regulator. Additionally, the NRC provides requirements for the physical protection of stored spent nuclear fuel and high-level radioactive waste at 10 CFR Chap. 73.51. For permanent closure approval, the applicant must provide a detailed description of the measures to be employed-such as land use controls, construction of monuments, and preservation of records. The NRC's regulatory role in any licensing action is to apply the applicable regulations and guidance, and to review applications for proposed actions to determine if compliance with regulations has been achieved. The burden of proof is on the applicant or licensee to show that the proposed action is safe, to demonstrate that regulations are met, and to ensure continued compliance with the regulations

Results From an International Simulation Study on Coupled Thermal, Hydrological, and Mechanical (THM) Processes Near Geological Nuclear Waste Repositories

International Nuclear Information System (INIS)

J. Rutqvist; D. Barr; J.T. Birkholzer; M. Chijimatsu; O. Kolditz; Q. Liu; Y. Oda; W. Wang; C. Zhang

2006-01-01

As part of the ongoing international DECOVALEX project, four research teams used five different models to simulate coupled thermal, hydrological, and mechanical (THM) processes near waste emplacement drifts of geological nuclear waste repositories. The simulations were conducted for two generic repository types, one with open and the other with back-filled repository drifts, under higher and lower postclosure temperatures, respectively. In the completed first model inception phase of the project, a good agreement was achieved between the research teams in calculating THM responses for both repository types, although some disagreement in hydrological responses is currently being resolved. In particular, good agreement in the basic thermal-mechanical responses was achieved for both repository types, even though some teams used relatively simplified thermal-elastic heat-conduction models that neglected complex near-field thermal-hydrological processes. The good agreement between the complex and simplified process models indicates that the basic thermal-mechanical responses can be predicted with a relatively high confidence level

Salt Repository Project Waste Package Program Plan: Draft

International Nuclear Information System (INIS)

Carr, J.A.; Cunnane, J.C.

1986-01-01

Under the direction of the Office of Civilian Radioactive Waste Management (OCRWM) created within the DOE by direction of the Nuclear Waste Policy Act of 1982 (NWPA), the mission of the Salt Repository Project (SRP) is to provide for the development of a candidate salt repository for disposal of high-level radioactive waste (HLW) and spent reactor fuel in a manner that fully protects the health and safety of the public and the quality of the environment. In consideration of the program needs and requirements discussed above, the SRP has decided to develop and issue this SRP Waste Package Program Plan. This document is intended to outline how the SRP plans to develop the waste package design and to show, with reasonable assurance, that the developed design will satisfy applicable requirements/performance objectives. 44 refs., 16 figs., 16 tabs

America's nuclear waste backlog

International Nuclear Information System (INIS)

Benenson, R.

1981-01-01

This report discusses three topics: concern and controversy relating to nuclear waste; high-level waste storage and politics of waste disposal. The most pressing waste disposal problem concerns spent fuel assemblies from commercial nuclear power plants. It was expected that commercial spent fuel would be sent to commercial reprocessing plants. The feasibility of commercial reprocessing in the United States is contingent on the expansion of the nuclear power industry. The current high-level liquid waste inventory is about 77 million gallons. These are stored at Richland, Washington; Aiken, South Carolina; and Idaho Falls, Idaho. The only commercial high-level wastes ever produced are stored at the defunct reprocessing facility at West Valley, New York. A high-level waste repository must be capable of isolating wastes that will remain dangerous for thousands of years. Salt has long been considered the most suitable medium for high-level and transuranic waste disposal. The timetable for opening a deep geological repository is one of the issues that will have to be dealt with by Congress. The 97th Congress appears ready to act on high-level nuclear waste legislation. Even opponents of nuclear expansion admit the necessity of legislation. Even if Congress gets its act together, it does not mean that the nuclear waste issue is gone. There are still unknowns - future of reprocessing, the needs and demands of the military; the health of the nuclear power industry; the objections of residents in potential site areas; the possibility of a state veto, and the unsolved technological problems in geologic site selection

Performance analysis of a repository for low and intermediate level reactor waste

International Nuclear Information System (INIS)

Vieno, T.; Nordman, H.; Vuori, S.; Peltonen, E.

1987-01-01

In Finland, utilities producing nuclear energy are responsible for the management of the radioactive waste, including final disposal. As regards low and intermediate level waste, the approach has been adopted to employ the power plant sites for locations of repositories. The repositories will be excavated at the depth of about 50 to 125 m in the bedrock of the two Finnish nuclear power plant sites, Loviisa and Olkiluoto. The performance analysis presented in this paper has been carried out for the Preliminary Safety Analysis Report (PSAR) of the Olkiluoto repository. A flexible model has been developed to estimate the release of radionuclides from waste packages and their subsequent transport through the engineered barriers in the repository. Gradual degradation of the engineered barriers is accounted for by altering parameters at fixed time points. Safety margins of the disposal concept have been evaluated by including disturbed evolution scenarios in the analysis. 13 references, 10 figures, 2 tables

Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Rechard, R.P.

1993-12-01

This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste, as mandated by the Nuclear Waste Policy Act of 1982. The waste forms comprised about 700 metric tons of initial heavy metal (or equivalent units) stored at the INEL: graphite spent fuel, experimental low enriched and highly enriched spent fuel, and high-level waste generated during reprocessing of some spent fuel. Five different waste treatment options were studied; in the analysis, the options and resulting waste forms were analyzed separately and in combination as five waste disposal groups. When the waste forms were studied in combination, the repository was assumed to also contain vitrified high-level waste from three DOE sites for a common basis of comparison and to simulate the impact of the INEL waste forms on a moderate-sized repository, The performance of the waste form was assessed within the context of a whole disposal system, using the U.S. Environmental Protection Agency's Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes, 40 CFR 191, promulgated in 1985. Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories

Dynamic use of geoscience information to develop scientific understanding for a nuclear waste repository

International Nuclear Information System (INIS)

Cook, N.G.W.; Tsang, C.F.

1990-01-01

The development and safety evaluation of a nuclear waste geologic repository require a proper scientific understanding of the site response. Such scientific understanding depends on information from a number of geoscience disciplines, including geology, geophysics, geochemistry, geomechanics and hydrogeology. The information comes in four stages: (1) general regional survey data base, (2) surface-based testing, (3) exploratory shaft testing, and (4) repository construction and evaluation. A discussion is given on the dynamic use of the information through the different stages. We point out the need for abstracting, deriving and updating a quantitative spatial and process model (QSPM) to develop a scientific understanding of site responses as a crucial element in the dynamic procedure. 2 figs

Socioeconomic impacts of large-scale developments: implications for high-level nuclear waste repositories

International Nuclear Information System (INIS)

Murdock, S.H.; Leistritz, F.L.; Hamm, R.R.

1983-01-01

High-level nuclear waste repositories will likely be located in sparsely settled rural areas in the US. These projects will significantly affect the economic, demographic, public service, fiscal, and social (the socioeconomic) dimensions of those rural areas. The impacts and means of mitigating them thus require careful analysis. This paper examines some of the potential socioeconomic impacts likely to occur in rural areas as a result of repository siting and development, and it describes some of the characteristics of mitigation programs that are likely to be necessary, if the impacts are to be addressed. Both (1) standard impacts, those resulting from the fact that, like many other large-scale developments, repositories will involve a substantial number of new workers and residents (relative to the size of existing communities), and (2) special impacts, those resulting from the fact that repositories store radioactive materials, are examined. The discussion indicates that economic, demographic, public service, fiscal, and social impacts (standard and special) of these repositories will be substantial and problematic in many cases. Unless the impacts are effectively addressed with carefully planned and well financed mitigation efforts that insure that high-quality planning information is provided to local residents, and that local residents are involved in impact planning and management throughout the siting and development process, repository siting is unlikely to be effectively and equitably achieved. 44 references

Stability of underground excavations in a repository system

International Nuclear Information System (INIS)

Calash, A.Y.; Greer, J.C.; Andrea, S.J.; Chowdhury, A.H.; Nguyen, V.V.

1988-01-01

The DOE is investigating the feasibility of constructing a deep geologic repository at the Hanford Site, Washington, for the permanent disposal of nuclear waste. The underground openings associated with the repository design include shafts, tunnels, emplacement rooms and boreholes. The stability of these underground openings, the extent and characteristics of the disturbed zones due to excavation, and their effects on groundwater flow path and travel time have a primary influence on the performance assessment of the Hanford Site as a nuclear waste repository. This study is being done in accordance with the requirements of the NRC. Results of structural analyses of shafts and tunnels under in situ stresses and/or medium weight are presented in this paper. Four different analyses were carried out to analyze the shaft: a plane strain model, axisymmetric model, 3-D model of a single material medium, and 3-D model of a three material medium

Evaluation of commercial repository capacity for the disposal of defense high-level waste. Comments and responses for DOE/DP--0020

International Nuclear Information System (INIS)

1985-12-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) requires that the President evaluate the use of disposal capacity at one or more repositories to be developed for permanent disposal of civilian spent nuclear fuel and high-level radioactive waste for the disposal of defense high-level radioactive waste. The Department of Energy prepared a report titled ''An Evaluation of Commercial Repository Capacity for the Disposal of Defense High-Level Waste,'' DOE/DP-0020, to provide input for the President's evaluation. The report constituted the Department's input and recommendation to be considered by the President in making his evaluation. Although not required by the Act, the Department made the July 1984 draft of the report available to the general public for review and comment in order to increase public awareness, and develop a public record on the issue of disposal of defense high-level waste. Over 400 copies of the draft report were distributed. Thirty comment letters containing over 400 comments were received from representatives of states, localities, and Indian tribes, federal agencies, organizations representing utilities, public interest groups, individual utilities, and private citizens. All letters were reviewed and considered. Where appropriate, changes were made in the final report reflecting the comments received

Deep Geologic Nuclear Waste Disposal - No New Taxes - 12469

Energy Technology Data Exchange (ETDEWEB)

Conca, James [RJLee Group, Inc., Pasco WA 509.205.7541 (United States); Wright, Judith [UFA Ventures, Inc., Richland, WA (United States)

2012-07-01

To some, the perceived inability of the United States to dispose of high-level nuclear waste justifies a moratorium on expansion of nuclear power in this country. Instead, it is more an example of how science yields to social pressure, even on a subject as technical as nuclear waste. Most of the problems, however, stem from confusion on the part of the public and their elected officials, not from a lack of scientific knowledge. We know where to put nuclear waste, how to put it there, how much it will cost, and how well it will work. And it's all about the geology. The President's Blue Ribbon Commission on America's Nuclear Future has drafted a number of recommendations addressing nuclear energy and waste issues (BRC 2011) and three recommendations, in particular, have set the stage for a new strategy to dispose of high-level nuclear waste and to manage spent nuclear fuel in the United States: 1) interim storage for spent nuclear fuel, 2) resumption of the site selection process for a second repository, and 3) a quasi-government entity to execute the program and take control of the Nuclear Waste Fund in order to do so. The first two recommendations allow removal and storage of spent fuel from reactor sites to be used in the future, and allows permanent disposal of actual waste, while the third controls cost and administration. The Nuclear Waste Policy Act of 1982 (NPWA 1982) provides the second repository different waste criteria, retrievability, and schedule, so massive salt returns as the candidate formation of choice. The cost (in 2007 dollars) of disposing of 83,000 metric tons of heavy metal (MTHM) high-level waste (HLW) is about $ 83 billion (b) in volcanic tuff, $ 29 b in massive salt, and $ 77 b in crystalline rock. Only in salt is the annual revenue stream from the Nuclear Waste Fund more than sufficient to accomplish this program without additional taxes or rate hikes. The cost is determined primarily by the suitability of the geologic

Safety assessment of geologic repositories for nuclear waste

International Nuclear Information System (INIS)

Bartlett, J.W.; Burkholder, H.C.; Winegardner, W.K.

1977-01-01

Consideration of geologic isolation for final disposition of radioactive wastes has led to the need for evaluation of the safety of the concept. Such evaluations require consideration of factors not encountered in conventional risk analysis: consequences at times and places far removed from the repository site; indirect, complex, and alternative pathways between the waste and the point of potential consequences; a highly limited data base; and limited opportunity for experimental verification of results. R and D programs to provide technical safety evaluations are under way. Three methods are being considered for the probabilistic aspects of the evaluations: fault tree analysis, repository simulation analysis, and system stability analysis. Nuclide transport models, currently in a relatively advanced state of development, are used to evaluate consequences of postulated loss of geologic isolation. This paper outlines the safety assessment methods, unique features of the assessment problem that affect selection of methods and reliability of results, and available results. It also discusses potential directions for future work

Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Rechard, R.P.

1993-12-01

This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste. Although numerous caveats must be placed on the results, the general findings were as follows: Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories

Nuclear Waste Facing the Test of Time: The Case of the French Deep Geological Repository Project.

Science.gov (United States)

Poirot-Delpech, Sophie; Raineau, Laurence

2016-12-01

The purpose of this article is to consider the socio-anthropological issues raised by the deep geological repository project for high-level, long-lived nuclear waste. It is based on fieldwork at a candidate site for a deep storage project in eastern France, where an underground laboratory has been studying the feasibility of the project since 1999. A project of this nature, based on the possibility of very long containment (hundreds of thousands of years, if not longer), involves a singular form of time. By linking project performance to geology's very long timescale, the project attempts "jump" in time, focusing on a far distant future, without understanding it in terms of generations. But these future generations remain measurements of time on the surface, where the issue of remembering or forgetting the repository comes to the fore. The nuclear waste geological storage project raises questions that neither politicians nor scientists, nor civil society, have ever confronted before. This project attempts to address a problem that exists on a very long timescale, which involves our responsibility toward generations in the far future.

Status of Proposed Repository for Latin-American Spent Fuel

Energy Technology Data Exchange (ETDEWEB)

Ferrada, J.J.

2004-10-04

This report compiles preliminary information that supports the premise that a repository is needed in Latin America and analyzes the nuclear situation (mainly in Argentina and Brazil) in terms of nuclear capabilities, inventories, and regional spent-fuel repositories. The report is based on several sources and summarizes (1) the nuclear capabilities in Latin America and establishes the framework for the need of a permanent repository, (2) the International Atomic Energy Agency (IAEA) approach for a regional spent-fuel repository and describes the support that international institutions are lending to this issue, (3) the current situation in Argentina in order to analyze the Argentinean willingness to find a location for a deep geological repository, and (4) the issues involved in selecting a location for the repository and identifies a potential location. This report then draws conclusions based on an analysis of this information. The focus of this report is mainly on spent fuel and does not elaborate on other radiological waste sources.

Coupling of Nuclear Waste Form Corrosion and Radionuclide Transports in Presence of Relevant Repository Sediments

International Nuclear Information System (INIS)

Wall, Nathalie A.; Neeway, James J.; Qafoku, Nikolla P.; Ryan, Joseph V.

2015-01-01

Assessments of waste form and disposal options start with the degradation of the waste forms and consequent mobilization of radionuclides. Long-term static tests, single-pass flow-through tests, and the pressurized unsaturated flow test are often employed to study the durability of potential waste forms and to help create models that predict their durability throughout the lifespan of the disposal site. These tests involve the corrosion of the material in the presence of various leachants, with different experimental designs yielding desired information about the behavior of the material. Though these tests have proved instrumental in elucidating various mechanisms responsible for material corrosion, the chemical environment to which the material is subject is often not representative of a potential radioactive waste repository where factors such as pH and leachant composition will be controlled by the near-field environment. Near-field materials include, but are not limited to, the original engineered barriers, their resulting corrosion products, backfill materials, and the natural host rock. For an accurate performance assessment of a nuclear waste repository, realistic waste corrosion experimental data ought to be modeled to allow for a better understanding of waste form corrosion mechanisms and the effect of immediate geochemical environment on these mechanisms. Additionally, the migration of radionuclides in the resulting chemical environment during and after waste form corrosion must be quantified and mechanisms responsible for migrations understood. The goal of this research was to understand the mechanisms responsible for waste form corrosion in the presence of relevant repository sediments to allow for accurate radionuclide migration quantifications. The rationale for this work is that a better understanding of waste form corrosion in relevant systems will enable increased reliance on waste form performance in repository environments and potentially

Coupling of Nuclear Waste Form Corrosion and Radionuclide Transports in Presence of Relevant Repository Sediments

Energy Technology Data Exchange (ETDEWEB)

Wall, Nathalie A. [Washington State Univ., Pullman, WA (United States); Neeway, James J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, Nikolla P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ryan, Joseph V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-09-30

Assessments of waste form and disposal options start with the degradation of the waste forms and consequent mobilization of radionuclides. Long-term static tests, single-pass flow-through tests, and the pressurized unsaturated flow test are often employed to study the durability of potential waste forms and to help create models that predict their durability throughout the lifespan of the disposal site. These tests involve the corrosion of the material in the presence of various leachants, with different experimental designs yielding desired information about the behavior of the material. Though these tests have proved instrumental in elucidating various mechanisms responsible for material corrosion, the chemical environment to which the material is subject is often not representative of a potential radioactive waste repository where factors such as pH and leachant composition will be controlled by the near-field environment. Near-field materials include, but are not limited to, the original engineered barriers, their resulting corrosion products, backfill materials, and the natural host rock. For an accurate performance assessment of a nuclear waste repository, realistic waste corrosion experimental data ought to be modeled to allow for a better understanding of waste form corrosion mechanisms and the effect of immediate geochemical environment on these mechanisms. Additionally, the migration of radionuclides in the resulting chemical environment during and after waste form corrosion must be quantified and mechanisms responsible for migrations understood. The goal of this research was to understand the mechanisms responsible for waste form corrosion in the presence of relevant repository sediments to allow for accurate radionuclide migration quantifications. The rationale for this work is that a better understanding of waste form corrosion in relevant systems will enable increased reliance on waste form performance in repository environments and potentially

Low and intermediate level waste repositories: public involvement aspects

International Nuclear Information System (INIS)

Ferreira, Vinicius V.M.; Mourao, Rogerio P.; Fleming, Peter M.; Soares, Wellington A.; Braga, Leticia T.P.; Santos, Rosana A.M.

2009-01-01

The nuclear energy acceptance creates several problems, and one of the most important is the disposal of the radioactive waste. International experiences show that not only environmental, radiological and technical questions have to be analyzed, but the public opinion about the project must be considered. The objective of this article is to summarize some public involvement aspects associated with low and intermediate level waste repositories. Experiences from USA, Canada, South Africa, Ukraine and other countries are studied and show the importance of the population in the site selection process for a repository. (author)

Nevada Nuclear Waste Storage Investigations: Exploratory Shaft Facility fluids and materials evaluation

Energy Technology Data Exchange (ETDEWEB)

West, K.A.

1988-11-01

The objective of this study was to determine if any fluids or materials used in the Exploratory Shaft Facility (ESF) of Yucca Mountain will make the mountain unsuitable for future construction of a nuclear waste repository. Yucca Mountain, an area on and adjacent to the Nevada Test Site in southern Nevada, USA, is a candidate site for permanent disposal of high-level radioactive waste from commercial nuclear power and defense nuclear activities. To properly characterize Yucca Mountain, it will be necessary to construct an underground test facility, in which in situ site characterization tests can be conducted. The candidate repository horizon at Yucca Mountain, however, could potentially be compromised by fluids and materials used in the site characterization tests. To minimize this possibility, Los Alamos National Laboratory was directed to evaluate the kinds of fluids and materials that will be used and their potential impacts on the site. A secondary objective was to identify fluids and materials, if any, that should be prohibited from, or controlled in, the underground. 56 refs., 19 figs., 11 tabs.

Nevada Nuclear Waste Storage Investigations: Exploratory Shaft Facility fluids and materials evaluation

International Nuclear Information System (INIS)

West, K.A.

1988-11-01

The objective of this study was to determine if any fluids or materials used in the Exploratory Shaft Facility (ESF) of Yucca Mountain will make the mountain unsuitable for future construction of a nuclear waste repository. Yucca Mountain, an area on and adjacent to the Nevada Test Site in southern Nevada, USA, is a candidate site for permanent disposal of high-level radioactive waste from commercial nuclear power and defense nuclear activities. To properly characterize Yucca Mountain, it will be necessary to construct an underground test facility, in which in situ site characterization tests can be conducted. The candidate repository horizon at Yucca Mountain, however, could potentially be compromised by fluids and materials used in the site characterization tests. To minimize this possibility, Los Alamos National Laboratory was directed to evaluate the kinds of fluids and materials that will be used and their potential impacts on the site. A secondary objective was to identify fluids and materials, if any, that should be prohibited from, or controlled in, the underground. 56 refs., 19 figs., 11 tabs

Role of natural analogs in performance assessment of nuclear waste repositories

International Nuclear Information System (INIS)

Sagar, B.; Wittmeyer, G.W.

1995-01-01

Mathematical models of the flow of water and transport of radionuclides in porous media will be used to assess the ability of deep geologic repositories to safely contain nuclear waste. These models must, in some sense, be validated to ensure that they adequately describe the physical processes occurring within the repository and its geologic setting. Inasmuch as the spatial and temporal scales over which these models must be applied in performance assessment are very large, validation of these models against laboratory and small-scale field experiments may be considered inadequate. Natural analogs may provide validation data that are representative of physico-chemical processes that occur over spatial and temporal scales as large or larger than those relevant to repository design. The authors discuss the manner in which natural analog data may be used to increase confidence in performance assessment models and conclude that, while these data may be suitable for testing the basic laws governing flow and transport, there is insufficient control of boundary and initial conditions and forcing functions to permit quantitative validation of complex, spatially distributed flow and transport models. The authors also express their opinion that, for collecting adequate data from natural analogs, resources will have to be devoted to them that are much larger than are devoted to them at present

The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

International Nuclear Information System (INIS)

Swanson, Juliet S.; Cherkouk, Andrea; Arnold, Thuro; Meleshyn, Artur; Reed, Donald T.

2016-01-01

This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and ''repository microbiology'' related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that will most likely underscore the conservative value of that case.

The Microbiology of Subsurface, Salt-Based Nuclear Waste Repositories: Using Microbial Ecology, Bioenergetics, and Projected Conditions to Help Predict Microbial Effects on Repository Performance

Energy Technology Data Exchange (ETDEWEB)

Swanson, Juliet S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cherkouk, Andrea [Helmholtz-Zentrum Dresden-Rossendorf, Rossendorf (Germany); Arnold, Thuro [Helmholtz-Zentrum Dresden-Rossendorf, Rossendorf (Germany); Meleshyn, Artur [Gesellschaft fur Anlagen und Reaktorsicherheit, Braunschweig (Germany); Reed, Donald T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-11-17

This report summarizes the potential role of microorganisms in salt-based nuclear waste repositories using available information on the microbial ecology of hypersaline environments, the bioenergetics of survival under high ionic strength conditions, and “repository microbiology” related studies. In areas where microbial activity is in question, there may be a need to shift the research focus toward feasibility studies rather than studies that generate actual input for performance assessments. In areas where activity is not necessary to affect performance (e.g., biocolloid transport), repository-relevant data should be generated. Both approaches will lend a realistic perspective to a safety case/performance scenario that will most likely underscore the conservative value of that case.

Limitations to the use of two-dimensional thermal modeling of a nuclear waste repository

International Nuclear Information System (INIS)

Davis, B.W.

1979-01-01

Thermal modeling of a nuclear waste repository is basic to most waste management predictive models. It is important that the modeling techniques accurately determine the time-dependent temperature distribution of the waste emplacement media. Recent modeling studies show that the time-dependent temperature distribution can be accurately modeled in the far-field using a 2-dimensional (2-D) planar numerical model; however, the near-field cannot be modeled accurately enough by either 2-D axisymmetric or 2-D planar numerical models for repositories in salt. The accuracy limits of 2-D modeling were defined by comparing results from 3-dimensional (3-D) TRUMP modeling with results from both 2-D axisymmetric and 2-D planar. Both TRUMP and ADINAT were employed as modeling tools. Two-dimensional results from the finite element code, ADINAT were compared with 2-D results from the finite difference code, TRUMP; they showed almost perfect correspondence in the far-field. This result adds substantially to confidence in future use of ADINAT and its companion stress code ADINA for thermal stress analysis. ADINAT was found to be somewhat sensitive to time step and mesh aspect ratio. 13 figures, 4 tables

The German quality system for waste repositories

International Nuclear Information System (INIS)

Beckmerhagen, I.; Berg, H.P.; Brennecke, P.

1993-01-01

The Bundesamt fuer Strahlenschutz (BfS)--Federal Office for Radiation protection--has to guarantee that the requirements resulting from different regulations concerning planning, design, construction, operation and decommissioning of a waste repository are fulfilled. In addition, the results of the safety assessments lead to nuclear-specific requirements on the design of the plant as well as to requirements on the radioactive waste packages intended to be disposed of. Therefore, the implementation of a quality assurance (QA) and quality control (QC) system is an essential task in order to ensure that the designed quality is achieved so that the necessary precaution against damage is taken. In this paper, a detailed description of QA and QC to be applied to the planned Konrad repository as well as the basic principles and the present status of the waste package QC are indicated and discussed

The conceptual design of waste repository for radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity

International Nuclear Information System (INIS)

Yamamoto, Masayuki; Hashimoto, Naro

2002-02-01

Advisory Committee on Nuclear Fuel Cycle Backend Policy reported the basic approach to the RI and Institute etc. wastes on March 2002. According to it, radioactive waste form medical, industrial and research facilities should be classified by their radioactivity properties and physical and chemical properties, and should be disposed in the appropriate types of repository with that classification. For the radioactive waste containing comparatively high radioactivity generated from reactors, NSC has established the Concentration limit for disposal. NSC is now discussing about the limit for the radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity. Japan Nuclear Cycle Development Institute (JNC) preliminary studied about the repository for radioactive waste from medical, industrial and research facilities and discussed about the problems for design on H12. This study was started to consider those problems, and to develop the conceptual design of the repository for radioactive waste from medical, industrial and research facilities. Safety assessment for that repository is also performed. The result of this study showed that radioactive waste from medical, industrial and research facilities of high activity should be disposed in the repository that has higher performance of barrier system comparing with the vault type near surface facility. If the conditions of the natural barrier and the engineering barrier are clearer, optimization of the design will be possible. (author)

Developing multinational radioactive waste repositories: Infrastructural framework and scenarios of cooperation

International Nuclear Information System (INIS)

2004-10-01

Currently the management of radioactive wastes centres on national strategies for collection, treatment, interim storage and disposal. This tendency to focus exclusively on national strategies reflects the fact that radioactive waste is a sensitive political issue, making cooperation among countries difficult. It is consistent with the accepted principle that a country that enjoys the benefit of nuclear energy, or the utilization of nuclear technology, should also take full responsibility for managing the generated radioactive waste. However, there are countries whose radioactive waste volumes do not easily justify a national repository, and/or countries that do not have the resources or favourable natural conditions for waste disposal to dedicate to a national repository project or would prefer to collaborate in shared initiatives because of their economic advantages. In such cases it may be appropriate for these countries to engage in a multinational collaborative effort to ensure that they have access to a common repository, in order that they can fulfil their responsibilities for their managing wastes safely. In response to requests from several Member States expressing an interest in multinational disposal options, the IAEA produced in 1998 a TECDOC outlining the important factors to be taken into account in the process of realizing such options. These factors include for example, technical (safety), institutional (legal, safeguards), economic (financial) socio-political (public acceptance) and ethical considerations. The present report reviews the work done in the previous study, taking into account developments since its publication as well as current activities in the field of multinational repositories. The report attempts to define the concepts involved in the creation of multinational repositories, to explore the likely scenarios, to examine the conditions for successful implementation, and to point out the benefits and challenges inherent to

General guidelines for recommendation of sites for nuclear waste repositories

International Nuclear Information System (INIS)

1983-01-01

These guidelines were developed in accordance with the requirements of Section 112(a) of the Nuclear Waste Policy Act of 1982 for use by the Secretary of Energy in evaluating the suitability of sites for the development of repositories. The guidelines will be used for suitability evaluations and determinations made pursuant to Section 112(b) and any preliminary suitability determinations required by Section 114(f). The guidelines set forth in this Part are intended to complement the requirements set forth in the Act, 10 CFR Part 60, and 40 CFR Part 191. In applying these guidelines, the DOE will resolve any inconsistencies between these guidelines and the above documents in a manner determined by the DOE to most closely agree with the intent of the Act

Applicability of risk-informed criticality methodology to spent fuel repositories

International Nuclear Information System (INIS)

Mays, C.; Thomas, D.A.; Favet, D.

2000-01-01

An important objective of geologic disposal is keeping the fissionable material in a condition so that a self-sustaining nuclear chain reaction (criticality) is highly unlikely. This objective supports the overall performance objective of any repository, which is to protect the health and safety of the public by limiting radiological exposure. This paper describes a risk-informed, performance-based methodology, which combines deterministic and probabilistic approaches for evaluating the criticality potential of high-level waste and spent nuclear fuel after the repository is sealed and permanently closed (postclosure). (authors)

Nuclear waste management. Pioneering solutions from Finland

International Nuclear Information System (INIS)

Rasilainen, Kari

2016-01-01

Presentation outline: Background: Nuclear energy in Finland; Nuclear Waste Management (NWM) Experiences; Low and Intermediate Level Waste (LILW); High Level Waste - Deep Geological Repository (DGR); NWM cost estimate in Finland; Conclusions: World-leading expert services

Panel report on coupled thermo-mechanical-hydro-chemical processes associated with a nuclear waste repository

International Nuclear Information System (INIS)

Tsang, C.F.; Mangold, D.C.

1984-07-01

Four basic physical processes, thermal, hydrological, mechanical and chemical, are likely to occur in 11 different types of coupling during the service life of an underground nuclear waste repository. A great number of coupled processes with various degrees of importance for geological repositories were identified and arranged into these 11 types. A qualitative description of these processes and a tentative evaluation of their significance and the degree of uncertainty in prediction is given. Suggestions for methods of investigation generally include, besides theoretical work, laboratory and large scale field testing. Great efforts of a multidisciplinary nature are needed to elucidate details of several coupled processes under different temperature conditions in different geological formations. It was suggested that by limiting the maximum temperature to 100 0 C in the backfill and in the host rock during the whole service life of the repository the uncertainties in prediction of long-term repository behavior might be considerably reduced

Panel report on coupled thermo-mechanical-hydro-chemical processes associated with a nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Tsang, C.F.; Mangold, D.C. (eds.)

1984-07-01

Four basic physical processes, thermal, hydrological, mechanical and chemical, are likely to occur in 11 different types of coupling during the service life of an underground nuclear waste repository. A great number of coupled processes with various degrees of importance for geological repositories were identified and arranged into these 11 types. A qualitative description of these processes and a tentative evaluation of their significance and the degree of uncertainty in prediction is given. Suggestions for methods of investigation generally include, besides theoretical work, laboratory and large scale field testing. Great efforts of a multidisciplinary nature are needed to elucidate details of several coupled processes under different temperature conditions in different geological formations. It was suggested that by limiting the maximum temperature to 100{sup 0}C in the backfill and in the host rock during the whole service life of the repository the uncertainties in prediction of long-term repository behavior might be considerably reduced.

Social impacts of hazardous and nuclear facilities and events: Implications for Nevada and the Yucca Mountain high-level nuclear waste repository; [Final report

Energy Technology Data Exchange (ETDEWEB)

Freudenburg, W.R. [Wisconsin Univ., Madison, WI (United States); Carter, L.F.; Willard, W. [Washington State Univ., Pullman, WA (United States); Lodwick, D.G. [Miami Univ., Oxford, OH (United States); Hardert, R.A. [Arizona State Univ., Tempe, AZ (United States); Levine, A.G. [State Univ. of New York, Buffalo, NY (United States). Dept. of Sociology; Kroll-Smith, S. [New Orleans Univ., LA (United States); Couch, S.R. [Pennsylvania State Univ., University Park, PA (United States); Edelstein, M.R. [Ramapo College, Mahwah, NJ (United States)

1992-05-01

Social impacts of a nuclear waste repository are described. Various case studies are cited such as Rocky Flats Plant, the Feed Materials Production Center, and Love Canal. The social impacts of toxic contamination, mitigating environmental stigma and loss of trust are also discussed.

Researching radioactive waste disposal. [Underground repository

Energy Technology Data Exchange (ETDEWEB)

Feates, F; Keen, N [UKAEA Research Group, Harwell. Atomic Energy Research Establishment

1976-02-16

At present it is planned to use the vitrification process to convert highly radioactive liquid wastes, arising from nuclear power programme, into glass which will be contained in steel cylinders for storage. The UKAEA in collaboration with other European countries is currently assessing the relative suitability of various natural geological structures as final repositories for the vitrified material. The Institute of Geological Sciences has been commissioned to specify the geological criteria that should be met by a rock structure if it is to be used for the construction of a repository though at this stage disposal sites are not being sought. The current research programme aims to obtain basic geological data about the structure of the rocks well below the surface and is expected to continue for at least three years. The results in all the European countries will then be considered so that the United Kingdom can choose a preferred method for isolating their wastes. It is only at that stage that a firm commitment may be made to select a site for a potential repository, when a far more detailed scientific research study will be instituted. Heat transfer problems and chemical effects which may occur within and around repositories are being investigated and a conceptual design study for an underground repository is being prepared.

Development and application of a quality assurance system for waste repositories

International Nuclear Information System (INIS)

Beckmerhagen, I.; Berg, H.P.

1996-01-01

A large set of requirements are developed for the structures, systems and components of a waste repository. These requirements cover different regulations concerning planning, design, construction, operation and decommissioning of a waste repository as well as nuclear-specific requirements on the design of the plant. The implementation of a quality assurance (QA) system is an essential task in order to ensure that the requirements are fulfilled by systematic means. The QA system for the German repositories for radioactive waste is built up as a hierarchic system and described in more detail in particular covering aspects like maintenance of QA relevant systems, structures and components as well as the procedure in case of changes. For the operational phase of a repository a separate site-specific manual had to be developed. Such a manual has been elaborated for the operation of the Morsleben repository; main topics of this manual are presented

Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 22. Nuclear considerations for repository design

International Nuclear Information System (INIS)

1978-04-01

This volume, Y/OWI/TM-36/22, ''Nuclear Considerations for Repository Design,'' is one of a 23-volume series, ''Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-36, which supplements the ''Contribution to Draft Generic Environmental Impact Statement on Commercial Waste Management: Radioactive Waste Isolation in Geologic Formations,'' Y/OWI/TM-44. The series provides a more complete technical basis for the preconceptual designs, resource requirements, and environmental source terms associated with isolating commercial LWR wastes in underground repositories in salt, granite, shale and basalt. Wastes are considered from three fuel cycles: uranium and plutonium recycling, no recycling of spent fuel and uranium-only recycling. Included in this volume are baseline design considerations such as characteristics of canisters, drums, casks, overpacks, and shipping containers; maximum allowable and actual decay-heat levels; and canister radiation levels. Other topics include safeguard and protection considerations; occupational radiation exposure including ALARA programs; shielding of canisters, transporters and forklift trucks; monitoring considerations; mine water treatment; canister integrity; and criticality calculations

Experience from developed and licensing an underground repository for low and intermediate level radioactive wastes

International Nuclear Information System (INIS)

Ebel, K.; Richter, D.

1988-01-01

In the German Democratic Republic an abandoned salt mine was selected and reconstructed to serve as a central repository for low and intermediate level wastes from nuclear power plants and radioisotope production and application from all over the country. The decision to establish such a repository was based on safety and technical-economic studies performed in the 1960s. The repository is owned by the main waste producer, the nuclear plant utility. It was designed, constructed and commissioned during 1972-1978. The licensing steps included a site licence (1972), a construction licence (1974), a comissioning licence and a continuous operation licence (1979). The paper reviews the overall choice of the disposal option, the responsibilities in radioactive waste management, the licensing and surveillance activities, the methods for transport and disposal, and the waste acceptance criteria established for the repository. (author)

Environmental release of carbon-14 gas from a hypothetical nuclear waste repository

International Nuclear Information System (INIS)

Lehto, M.A.; Merrell, G.B.

1994-01-01

Radioisotopes may form gases in a spent nuclear fuel waste package due to elevated temperatures or degradation of the fuel rods. Radioactive carbon-14, as gaseous carbon dioxide, is one of the gaseous radioisotopes of concern at an underground disposal facility for spent nuclear fuel and high-level radioactive waste. Carbon-14 dioxide may accumulate inside an intact waste container. Upon breach of the container, a potentially large pulse of carbon-14 dioxide gas may be released to the surrounding environment, followed by a lower, long-term continuous release. If the waste were disposed of in an unsaturated geologic environment, the carbon-14 gas would begin to move through the unsaturated zone to the accessible environment. This study investigates the transport of radioactive carbon-14 gas in geologic porous media using a one-dimensional analytical solution. Spent nuclear fuel emplaced in a deep geologic repository located at a generic unsaturated tuff site is analyzed. The source term for the carbon-14 gas and geologic parameters was obtained from previously published materials. The one-dimensional analytical solution includes diffusion, advection, radionuclide retardation, and radioactive decay terms. Two hypothetical sites are analyzed. One is dominated by advective transport, and the other is dominated by diffusive transport. The dominant transport mechanism at an actual site depends on the site characteristics. Results from the simulations include carbon-14 dioxide travel times to the accessible environment and the total release to the environment over a 10,000-year period. The results are compared to regulatory criteria

Disruptive event uncertainties in a perturbation approach to nuclear waste repository risk analysis

Energy Technology Data Exchange (ETDEWEB)

Harvey, T.F.

1980-09-01

A methodology is developed for incorporating a full range of the principal forecasting uncertainties into a risk analysis of a nuclear waste repository. The result of this methodology is a set of risk curves similar to those used by Rasmussen in WASH-1400. The set of curves is partially derived from a perturbation approach to analyze potential disruptive event sequences. Such a scheme could be useful in truncating the number of disruptive event scenarios and providing guidance to those establishing data-base development priorities.

Overweight truck shipments to nuclear waste repositories: legal, political, administrative and operational considerations

International Nuclear Information System (INIS)

1986-03-01

This report, prepared for the Chicago Operations Office and the Office of Civilian Radioactive Waste Management (OCRWM) of the US Department of Energy (DOE), identifies and analyzes legal, political, administrative, and operational issues that could affect an OCRWM decision to develop an overweight truck cask fleet for the commercial nuclear waste repository program. It also provides information required by DOE on vehicle size-and-weight administration and regulation, pertinent to nuclear waste shipments. Current legal-weight truck casks have a payload of one pressurized-water reactor spent fuel element or two boiling-water reactor spent fuel elements (1 PWR/2 BWR). For the requirements of the 1960s and 1970s, casks were designed with massive shielding to accommodate 6-month-old spent fuel; the gross vehicle weight was limited to 73,280 pounds. Spent fuel to be moved in the 1990s will have aged five years or more. Gross vehicle weight limitation for the Interstate highway system has been increased to 80,000 pounds. These changes allow the design of 25-ton legal-weight truck casks with payloads of 2 PWR/5 BWR. These changes may also allow the development of a 40-ton overweight truck cask with a payload of 4 PWR/10 BWR. Such overweight casks will result in significantly fewer highway shipments compared with legal-weight casks, with potential reductions in transport-related repository risks and costs. These advantages must be weighed against a number of institutional issues surrounding such overweight shipments before a substantial commitment is made to develop an overweight truck cask fleet. This report discusses these issues in detail and provides recommended actions to DOE

Continuing Science and Technology at the Proposed Yucca Mountain Repository

International Nuclear Information System (INIS)

Finch, R.J.

2005-01-01

Yucca Mountain, Nevada, was designated in 2002 to be the site for the nation's first permanent geological repository for spent nuclear fuel and high-level radioactive waste. The process of selecting a site for the repository began nearly 25 years ago with passage of the Nuclear Waste Policy Act in 1982. The Department of Energy (DOE) is responsible for submitting a license application to the Nuclear Regulatory Commission for constructing and operating the repository, and DOE's Office of Civilian Radioactive Waste Management (OCRWM) is charged with carrying out this action. The use of multiple natural and engineered barriers in the current repository design are considered by OCRWM to be sufficiently robust to warrant license approval; however, potential design enhancements and increased understanding of both natural and engineered barriers, especially over the long time frames during which the waste is to remain isolated from human contact continue to be examined. The Office of Science and Technology and International (OST andI) was created within OCRWM to help explore novel technologies that might lower overall costs and to develop a greater understanding of processes relevant to the long-term performance of the repository. A brief overview of Yucca Mountain, and the role that OST andI has in identifying technological or scientific advances that could make repository operations more efficient or performance more robust, will be presented. It is important to note, however, that adopting any of OST andI's technological or scientific developments will be at the discretion of OCRWM's Office of Repository Development (ORD)

Shifting strategies and precarious progress: Nuclear waste management in Canada

International Nuclear Information System (INIS)

Ramana, M.V.

2013-01-01

Canada has a lengthy history of trying to find a path for dealing with radioactive spent fuel and nuclear waste from its nuclear reactors. In the last decade, it has taken major strides towards this goal by evolving a process through which a site for a geological repository to sequester nuclear waste is to be selected. The Canadian Nuclear Waste Management Organization (NWMO) is in the early stages of the process of finding a community that is willing to host such a repository. Differences between the broad principles underlying siting and the processes for actually selecting the site have emerged as the NWMO proceeds with engaging local governments and specific communities. These differences and other conflicts, especially over new nuclear reactor construction, might pose hurdles in the path of successfully setting up a repository. - Highlights: • Canada has set up a process for siting a geological repository for nuclear waste. • The current challenge is to find a community willing to host such a repository. • Authorities are luring communities with the promise of jobs and local investment. • Potential new nuclear reactor construction might become a locus of conflict. • Success in actually setting up a repository is by no means guaranteed

Nuclear waste: Quarterly report on DOE's Nuclear Waste Program as of March 31, 1987

International Nuclear Information System (INIS)

1987-01-01

The Nuclear Waste Policy Act established a national program and policy for safely storing, transporting, and disposing of nuclear waste. This fact sheet provides the status of the Department of Energy's program activities. They include (1) the release of a draft amendment to the mission plan in which DOE extends by 5 years its target date for beginning first repository operations and information on DOE's decision to postpone site-specific activities for the second repository; (2) a monitored retrievable storage proposal and related documents; (3) receipts of comments from utilities, state regulators, and others on its Notice of Inquiry on proposals for the calculation of fees for defense waste disposal; and (4) information on the Nuclear Waste Fund collection of over /135.4 million in fees and investment income and obligations of $139 million for program activities. The fund balance as of March 31, 1987, was about $1.5 billion

Modelling of the degradation of cement in a nuclear waste repository

International Nuclear Information System (INIS)

Haworth, A.; Sharland, S.M.; Tweed, C.J.

1989-01-01

The current UK concept for a low- or intermediate-level nuclear waste repository includes a largely cementitious backfill. The cement provides a high pH environment in which the general corrosion rate of the metal canisters is reduced and the solubilities of many nuclides low. It has previously been assumed that this high pH will exist for a period of 10 7 years, however cement will degrade due to leaching of the solid components and attack from aqueous species in groundwater. In this paper the authors describe the preliminary stages of a model of the degradation of cement in a repository. The modelling involves the incorporation of a thermodynamic description of cement into the static code PHREEQE. This is then used in a coupled chemistry-transport model of simple leaching of cement using the code CHEQMATE. This preliminary modelling also provides a useful verification of CHEQMATE as a direct comparison with a THCCDM (a coupled code based on CHEMTRN) model is possible. Results from this preliminary model suggest that the fall in pH due to leaching is slow

Dynamic use of geoscience information to develop scientific understanding for a nuclear waste repository

International Nuclear Information System (INIS)

Cook, N.G.W.; Tsang, C.F.

1990-01-01

This paper discusses the development and safety evaluation of a nuclear waste geologic repository. Scientific understanding dependent upon information from a number of geoscience disciplines is described. A discussion is given on the dynamic use of the information through the different stages. The authors point out the need for abstracting, deriving and updating a quantitative spatial and process model (QSPM) to develop a scientific understanding of site responses as a crucial element in the dynamic procedure

Modelling of the THM-evolution of Olkiluoto nuclear waste repository

International Nuclear Information System (INIS)

Toprak, Erdem; Olivella, Sebastia; Mokni, Nadia; Pintado, Xavier

2012-01-01

Document available in extended abstract form only. This paper presents preliminary analyses of coupled Thermo-Hydro-Mechanical (THM) processes in the future nuclear waste repository in Olkiluoto (www.posiva.fi). A finite element program Code-Bright is used to perform modeling calculations of disposal tunnels in an underground repository for spent nuclear fuel. The repository will consist of a series of deposition holes in the bedrock. Bentonite buffer rings will surround the copper canisters containing spent fuel. As a protecting and isolating barrier between the waste canisters and the surrounding host rock, MX80 bentonite will be used as buffer material. Friedland clay is considered one of the best candidates to be used as drift backfill material to meet the long-term performance requirements set for backfilling of a disposal tunnel in the repository. Figure 1 shows a cross section of the spent nuclear final disposal facility. The time required for reaching full saturation, maximum temperature reached in canister, deformations in the buffer-backfill interface and stress-deformation balance in this interaction and also modeling of gap between canister and buffer ring are the main issued addressed of this study. A fundamental issue in modeling was to determine relevant thermal boundary conditions so that the details of THM-behavior could be captured by defining proper near-field thermal boundaries. In this study, it has been shown that temperature on the considered close boundaries depends on initial canister power, fuel power decay characteristic and rock thermal properties. The thermal boundary conditions fixed at the THM modeling have been calculated solving the thermal problem for the entire repository with the analytical solution (Ikonen, 2005). With regard to the hydraulic analyses, the time required for full saturation is sensitive to vapor diffusion, hydraulic conductivity and water retention curve of the buffer and the hydraulic conductivity of the rock. A

Groundwater recharge and discharge scenarios for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

Carpenter, D.W.; Steinborn, T.L.; Thorson, L.D.

1979-01-01

Twelve potential scenarios have been identified whereby groundwater may enter or exit a nuclear waste repository in bedded salt. The 12 scenarios may be grouped into 4 categories or failure modes: dissolution, fracturing, voids, and penetration. Dissolution modes include breccia pipe and breccia blanket formation, and dissolution around boreholes. Fracture modes include flow through preexisting or new fractures and the effects of facies changes. Voids include interstitial voids (pores) and fluid inclusions. Penetration modes include shaft and borehole sealing failures, undetected boreholes, and new mines or wells constructed after repository decommissioning. The potential importance of thermal effects on groundwater flow patterns and on the recharge-discharge process is discussed. The appropriate levels of modeling effort, and the interaction between the adequacy of the geohydrologic data base and the warranted degree of model complexity are also discussed

Status of United States civilian waste management program

International Nuclear Information System (INIS)

Lawrence, M.J.

1984-01-01

The Nuclear Waste Policy Act of 1982 confirms the Federal responsibility for nuclear waste management and provides for unprecedented involvement by States, Indian tribes and the public. The Act provides a comprehensive framework for disposing of spent nuclear fuel and high-level radioactive wastes of domestic origin generated by civilian nuclear power reactors. It establishes detailed schedules and procedures for selecting and developing geologic repositories; provides a mechanism for financing the cost of disposal; and sets forth other provisions relating to nuclear waste disposal. The other provisions of the Act include provision for a user-financed federal interim storage facility with time and quantity limitations, as well as strict Nuclear Regulatory Commission-prescribed eligibility criteria; a proposal for a Federally-owned and operated monitored retrievable storage (MRS) facility for the interim period prior to operation of a permanent repository; and provision for a Test and Evaluation Facility (TEF). This paper centers on the schedule and current status and siting of the first two geologic repositories

Towards a Swedish repository for spent fuel

International Nuclear Information System (INIS)

Ahlstroem, P.-E.

1997-01-01

Nuclear power is producing electricity for the benefit of society but is also leaving radioactive residues behind. It is our responsibility to handle these residues in a safe and proper manner. The development of a system for handling spent fuel from nuclear power plants has proceeded in steps. The same is true for the actual construction of facilities and will continue to be the case for the final repository for spent fuel and other types of long-lived wastes. The primary objective in constructing the repository will be to isolate and contain the radioactive waste. In case the isolation fails for some reason the multibarrier system should retain and retard the radionuclides that might come into contact with the groundwater. A repository is now planned to be built in two steps where the first step will include deposition of about 400 canisters with spent fuel. This first step should be finished in about 20 years from now and be followed by an extensive evaluation of the results from not only this particular step but also from the development of alternative routes before deciding on how to proceed. A special facility to encapsulate the spent fuel is also required. Such an encapsulation plant is proposed to be constructed as an extension of the existing interim storage CLAB. Finding a site for the repository is a critical issue in the implementation of any repository. The siting process started a few years ago and made some progress but is by no means yet completed. It will go on at least into the early part of the next decade. When the present nuclear power plants begin to be due for retirement there should also be some facilities in place to take permanent care of the long-lived radioactive residues. Progress in siting will be a prerequisite for success in our responsibility to make progress towards a safe permanent solution of the waste issue. (orig.)

Functions of an engineered barrier system for a nuclear waste repository in basalt

International Nuclear Information System (INIS)

Coons, W.E.; Moore, E.L.; Smith, M.J.; Kaser, J.D.

1980-01-01

Defined in this document are the functions of components selected for an engineered barrier system for a nuclear waste repository in basalt. The definitions provide a focal point for barrier material research and development by delineating the purpose and operative lifetime of each component of the engineered system. A five-component system (comprised of waste form, canister, buffer, overpack, and tailored backfill) is discussed in terms of effective operation throughout the course of repository history, recognizing that the emplacement environment changes with time. While components of the system are mutually supporting, redundancy is provided by subsystems of physical and chemical barriers which act in concert with the geology to provide a formidable barrier to transport of hazardous materials to the biosphere. The operating philosophy of the conceptual engineered barrier system is clarified by examples pertinent to storage in basalt, and a technical approach to barrier design and material selection is proposed. A method for system validation and qualification is also included which considers performance criteria proposed by external agencies in conjunction with site-specific models and risk assessment to define acceptable levels of system performance

Nuclear waste: Status of DOE's nuclear waste site characterization activities

International Nuclear Information System (INIS)

1987-01-01

Three potential nuclear waste repository sites have been selected to carry out characterization activities-the detailed geological testing to determine the suitability of each site as a repository. The sites are Hanford in south-central Washington State, Yucca Mountain in southern Nevada, and Deaf Smith in the Texas Panhandle. Two key issues affecting the total program are the estimations of the site characterization completion data and costs and DOE's relationship with the Nuclear Regulatory Commission which has been limited and its relations with affected states and Indian tribes which continue to be difficult

Use of swelling clays to reduce permeability and its potential application to nuclear waste repository sealing

International Nuclear Information System (INIS)

Moore, D.E.; Morrow, C.A.; Byerlee, J.D.

1982-01-01

The injection of swelling-clay slurries into joints or faults at a deep-burial nuclear waste disposal site may result in signficant permeability reductions for the effective containment of radioactive wastes. In an experiment conducted to illustrate the permeability change accompanying clay swelling, a coarse stone with interconnected pore spaces was injected with a clay-electrolyte slurry, modelling the pressure-grouting of a fractured repository rock. Subsequently, solutions with lower electroylte concentrations were driven through the clay-filled stone, corresponding to migration of lower salinity ground-waters through the clay-grouted fracture. The initial injection procedure reduced the permeability of the stone from 1--10 darcies to 700 nanodarcies; the changes in solution composition decreased permeability by more than 2 additional orders of magnitude to 3 nanodarcies. For application at a nuclear waste repository, the electrolyte concentration of the injected clay slurry should be made higher than that of the ground-water in the host rock. Subesquent interaction of the ground-water with the clays would initiate swelling and create the additional, post-injection permeability reductions that may be important in preventing the escape of buried radioactive wastes. The measured permeability of the clay filling is considerably lower than that of cement tested for borehole plugging. Clays also have the advantage over cement and chemical grouts in that they are geologically stable at relatively low temperatures and have a high capacity for radionuclide adsorption

JYT - Publicly financed nuclear waste management research programme

International Nuclear Information System (INIS)

Vuori, S.

1992-07-01

The nuclear waste management research in Finland is funded both by the state and the utilities (represented in cooperation by the Nuclear Waste Commission of the Finnish power companies). A coordinated research programme (JYT) comprising the publicly financed waste management studies was started in 1989 and continues until 1993. The utilities continue to carry out a parallel research programme according to their main financial and operational responsibility for nuclear waste management. The research programme covers the following main topic areas: (1) Bedrock characteristics, groundwater and repository, (2) Release and transport of radionuclides, (3) Performance and safety assessment of repositories, and (4) Waste management technology and costs

JYT - Publicly financed nuclear waste management research programme

International Nuclear Information System (INIS)

Vuori, S.

1993-06-01

The nuclear waste management research in Finland is funded both by the state and the utilities (represented in cooperation by the Nuclear Waste Commission of the Finnish power companies). A coordinated research programme (JYT) comprising the publicly financed waste management studies was started in 1989 and continues until 1993. The utilities continue to carry out a parallel research programme according to their main financial and operational responsibility for nuclear waste management. The research programme covers the following main topic areas: (1) Bedrock characteristics, groundwater and repository, (2) Release and transport of radionuclides, (3) Performance and safety assessment of repositories, and (4) Waste management technology and costs

JYT - Publicly financed nuclear waste management research programme

International Nuclear Information System (INIS)

Vuori, S.

1991-07-01

The nuclear waste management research in Finland is funded both by the state and the utilities (represented in cooperation by the Nuclear Waste Commission of the Finnish power companies). A coordinated research programme (JYT) comprising the publicly financed waste management studies was started in 1989 and continues until 1993. The utilities continue to carry out a parallel research programme according to their main financial and operational responsibility for nuclear waste management. The research programme covers the following main topic areas: (1) Bedrock characteristics, groundwater and repository, (2) Release and transport of radionuclides, (3) Performance and safety assessment of repositories, and (4) Waste management technology and costs

Potential role of ABC-assisted repositories in U.S. plutonium and high-level waste disposition

Energy Technology Data Exchange (ETDEWEB)

Berwald, D.; Favale, A.; Myers, T. [Grumman Aerospace Corporation, Bethpage, NY (United States)] [and others

1995-10-01

This paper characterizes the issues involving deep geologic disposal of LWR spent fuel rods, then presents results of an investigation to quantify the potential role of Accelerator-Based Conversion (ABC) in an integrated national nuclear materials and high level waste disposition strategy. The investigation used the deep geological repository envisioned for Yucca Mt., Nevada as a baseline and considered complementary roles for integrated ABC transmutation systems. The results indicate that although a U.S. geologic waste repository will continue to be required, waste partitioning and accelerator transmutation of plutonium, the minor actinides, and selected long-lived fission products can result in the following substantial benefits: plutonium burndown to near zero levels, a dramatic reduction of the long term hazard associated with geologic repositories, an ability to place several-fold more high level nuclear waste in a single repository, electricity sales to compensate for capital and operating costs.

Natural analogues, paradigm for manmade repositories for radioactive wastes

International Nuclear Information System (INIS)

Pavelescu, M.; Pavelescu, A.

2004-01-01

Natural analogues are given by nature. They show the results of natural processes which have lasted thousands or millions of years. They provide an excellent example of what could happen in an underground site, offering in the same time the opportunity to test by observation and measurement, many of the geochemical processes that are expected to influence in a realistic and appropriate way, the predicted reliability of the radioactive waste repository over long periods of geological time. The natural analogue studies attempt to understand the multiprocessing complexity of the natural system, which contrasts with the limitations of the laboratory experiments and bring arguments to overcome the difficult time scale issue. By this the natural analogues are a useful paradigm for manmade repository for radioactive wastes. The paper discusses the implicit link in the public mind between natural analogues and manmade waste repository with an accent of the positive impact on public acceptance. It is also discussed the decisive qualities of the natural analogues concerning providing valid long term data and increasing the confidence of the public for manmade repositories. The debate is conducting in terms of sustainable development, having at base high-level principles in order to protect humans and their environment, both now and in the future, from potential hazards arising from such wastes. Safe radwaste management involves the application of technology and resources in a regulated manner so that the public, workers and the environment are protected in accordance with the accepted national and international standards. There are at least seven high-level principles which are mentioned in the paper. It is presented the general concept of the deep geological repository, very important for an acceptable solution for the management of nuclear waste, what is a prerequisite for a renewal of nuclear power. Further are introduced natural and archaeological (manufactured) analogue

High level nuclear waste repository in salt: Sealing systems status and planning report: Draft report

International Nuclear Information System (INIS)

1985-09-01

This report documents the initial conceptual design studies for a repository sealing system for a high-level nuclear waste repository in salt. The first step in the initial design studies was to review the current design level, termed schematic designs. This review identified practicality of construction and development of a design methodology as two key issues for the conceptual design. These two issues were then investigated during the initial design studies for seal system materials, seal placement, backfill emplacement, and a testing and monitoring plan. The results of these studies have been used to develop a program plan for completion of the sealing system conceptual design. 60 refs., 26 figs., 18 tabs

Perceived risk, stigma, and potential economic impacts of a high-level nuclear waste repository in Nevada

International Nuclear Information System (INIS)

Slovic, P.; Layman, M.; Kraus, N.; Flynn, J.; Chalmers, J.; Gesell, G.

1991-01-01

This study investigates the potential impacts of the proposed nuclear waste repository at Yucca Mountain, Nevada, upon tourism, retirement and job-related migration, and business development in Las Vegas and the state. Adverse impacts may be expected to result from perceptions of risk, stigmatization, and socially amplified reactions to 'unfortunate events' associated with the repository (major and minor accidents, discoveries of radiation releases, evidence of mismanagement, attempts to sabotage or disrupt the facility, etc.). The conceptual underpinnings of risk perception, stigmatization, and social amplification are discussed and empirical data are presented to demonstrate how nuclear images associated with Las Vegas and the State of Nevada might trigger adverse economic effects. The possibility that intense negative imagery associated with the repository may cause significant harm to Nevada's economy can no longer be ignored by serious attempts to assess the risks and impacts of this unique facility. The behavioral processes described here appear relevant as well to the social impact assessment of any proposed facility that produces, uses, transports, or disposes of hazardous materials

Perceived risk, stigma, and potential economic impacts of a high-level nuclear waste repository in Nevada.

Science.gov (United States)

Slovic, P; Layman, M; Kraus, N; Flynn, J; Chalmers, J; Gesell, G

1991-12-01

This study investigates the potential impacts of the proposed nuclear waste repository at Yucca Mountain, Nevada, upon tourism, retirement and job-related migration, and business development in Las Vegas and the state. Adverse impacts may be expected to result from perceptions of risk, stigmatization, and socially amplified reactions to "unfortunate events" associated with the repository (major and minor accidents, discoveries of radiation releases, evidence of mismanagement, attempts to sabotage or disrupt the facility, etc.). The conceptual underpinnings of risk perception, stigmatization, and social amplification are discussed and empirical data are presented to demonstrate how nuclear images associated with Las Vegas and the State of Nevada might trigger adverse economic effects. The possibility that intense negative imagery associated with the repository may cause significant harm to Nevada's economy can no longer be ignored by serious attempts to assess the risks and impacts of this unique facility. The behavioral processes described here appear relevant as well to the social impact assessment of any proposed facility that produces, uses, transports, or disposes of hazardous materials.

A preliminary analysis of the risk of transporting nuclear waste to potential candidate commercial repository sites

International Nuclear Information System (INIS)

Madsen, M.M.

1984-01-01

In accordance with the provisions of the Nuclear Waste Policy Act of 1982, environmental assessments for potential candidate sites are required to provide a basis for selection of the first site for disposal of commercial radioactive waste in deep geologic repositories. A preliminary analysis of the impacts of transportation for each of the five potential sites will be described. Transportation was assumed to be entirely by truck or entirely by rail in order to obtain bounding impacts. This paper presents both radiological and nonradiological risks for the once-through fuel cycle

The new Wallula CO2 project may revive the old Columbia River Basalt (western USA) nuclear-waste repository project

Science.gov (United States)

Schwartz, Michael O.

2018-02-01

A novel CO2 sequestration project at Wallula, Washington, USA, makes ample use of the geoscientific data collection of the old nuclear waste repository project at the Hanford Site nearby. Both projects target the Columbia River Basalt (CRB). The new publicity for the old project comes at a time when the approach to high-level nuclear waste disposal has undergone fundamental changes. The emphasis now is on a technical barrier that is chemically compatible with the host rock. In the ideal case, the waste container is in thermodynamic equilibrium with the host-rock groundwater regime. The CRB groundwater has what it takes to represent the ideal case.

Nuclear waste disposal technology for Pacific Basin countries

International Nuclear Information System (INIS)

Langley, R.A. Jr.; Brothers, G.W.

1981-01-01

Safe long-term disposal of nuclear wastes is technically feasible. Further technological development offers the promise of reduced costs through elimination of unnecessary conservatism and redundance in waste disposal systems. The principal deterrents to waste disposal are social and political. The issues of nuclear waste storage and disposal are being confronted by many nuclear power countries including some of the Pacific Basin nuclear countries. Both mined geologic and subseabed disposal schemes are being developed actively. The countries of the Pacific Basin, because of their geographic proximity, could benefit by jointly planning their waste disposal activities. A single repository, of a design currently being considered, could hold all the estimated reprocessing waste from all the Pacific Basin countries past the year 2010. As a start, multinational review of alterntive disposal schemes would be beneficial. This review should include the subseabed disposal of radwastes. A multinational review of radwaste packaging is also suggested. Packages destined for a common repository, even though they may come from several countries, should be standardized to maximize repository efficiency and minimize operator exposure. Since package designs may be developed before finalization of a repository scheme and design, the packages should not have characteristics that would preclude or adversely affect operation of desirable repository options. The sociopolitical problems of waste disposal are a major deterrent to a multinational approach to waste disposal. The elected representatives of a given political entity have generally been reluctant to accept the waste from another political entity. Initial studies would, nevertheless, be beneficial either to a common solution to the problem, or to aid in separate solutions

Long-Term Information Management (LTIM) of Safeguards Data at Geological Repositories

International Nuclear Information System (INIS)

Haddal, R.; Finch, R.; Baldwin, G.

2016-01-01

Full text: The International Atomic Energy Agency (IAEA) has noted that long-term information management (LTIM) of safeguards data at geological repositories will be a significant challenge in the future as information and records management systems evolve and permanent disposal of nuclear materials becomes a high-priority in many countries. Identifying approaches to how information on buried high-level nuclear waste will be managed, handled, organized, archived, read, interpreted, and secured for the long-term (1000 years after repository closure and beyond) will be key to safeguards at repositories). The purpose of this study is to explore various long-term information management systems and how they may or may not be adapted for geological repositories for high-level waste. The study will also examine what types of safeguards-related data should be included in such a system. The study will also consider hypotheses about future needs and analyze the pros and cons of very long-term information management. (author

Federalist strategy for nuclear waste management

International Nuclear Information System (INIS)

Lee, K.N.

1980-01-01

The federal government plans to rely on a policy of consultation and concurrence with state governments in developing nuclear waste repositories. The weaknesses of the concurrence approach are analyzed, and an alternative institutional framework for locating a waste repository is proposed: a siting jury that provides representation for state and local interests, while maintaining a high level of technical review. The proposal could be tested in the siting of away-from-reactor storage facilities for spent nuclear fuel. 1 table

Designing shafts for handling high-level radioactive wastes in mined geologic repositories

International Nuclear Information System (INIS)

Hambley, D.F.; Morris, J.R.

1988-01-01

Waste package conceptual designs developed in the United States by the U.S. Department of Energy's Office of Civilian Radioactive Waste Management are the basis for specifying the dimensions and weights of the waste package and transfer cask combinations to be hoisted in the waste handling shafts in mined geologic repositories for high-level radioactive waste. The hoist, conveyance, counterweight, and hoist ropes are then sized. Also taken into consideration are overwind and underwind arrestors and safety features required by the U.S. Nuclear Regulatory Commission. Other design features such as braking systems, chairing system design, and hoisting speed are considered in specifying waste hoisting system parameters for example repository sites

Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory. Volume 2: Appendices

Energy Technology Data Exchange (ETDEWEB)

Rechard, R.P. [ed.

1993-12-01

This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste, as mandated by the Nuclear Waste Policy Act of 1982. The waste forms comprised about 700 metric tons of initial heavy metal (or equivalent units) stored at the INEL: graphite spent fuel, experimental low enriched and highly enriched spent fuel, and high-level waste generated during reprocessing of some spent fuel. Five different waste treatment options were studied; in the analysis, the options and resulting waste forms were analyzed separately and in combination as five waste disposal groups. When the waste forms were studied in combination, the repository was assumed to also contain vitrified high-level waste from three DOE sites for a common basis of comparison and to simulate the impact of the INEL waste forms on a moderate-sized repository, The performance of the waste form was assessed within the context of a whole disposal system, using the U.S. Environmental Protection Agency`s Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes, 40 CFR 191, promulgated in 1985. Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories.

The Analytical Repository Source-Term (AREST) model: Analysis of spent fuel as a nuclear waste form

International Nuclear Information System (INIS)

Apted, M.J.; Liebetrau, A.M.; Engel, D.W.

1989-02-01

The purpose of this report is to assess the performance of spent fuel as a final waste form. The release of radionuclides from spent nuclear fuel has been simulated for the three repository sites that were nominated for site characterization in accordance with the Nuclear Waste Policy Act of 1982. The simulation is based on waste package designs that were presented in the environmental assessments prepared for each site. Five distinct distributions for containment failure have been considered, and the release for nuclides from the UO 2 matrix, gap (including grain boundary), crud/surface layer, and cladding has been calculated with the Analytic Repository Source-Term (AREST) code. Separate scenarios involving incongruent and congruent release from the UO 2 matrix have also been examined using the AREST code. Congruent release is defined here as the condition in which the relative mass release rates of a given nuclide and uranium from the UO 2 matrix are equal to their mass ratios in the matrix. Incongruent release refers to release of a given nuclide from the UO 2 matrix controlled by its own solubility-limiting solid phase. Release of nuclides from other sources within the spent fuel (e.g., cladding, fuel/cladding gap) is evaluated separately from either incongruent or congruent matrix release. 51 refs., 200 figs., 9 tabs

A Deterministic Safety Assessment of a Pyro-processed Waste Repository

International Nuclear Information System (INIS)

Lee, Youn Myoung; Jeong, Jong Tae; Choi, Jong Won

2012-01-01

A GoldSim template program for a safety assessment of a hybrid-typed repository system, called 'A-KRS', in which two kinds of pyro-processed radioactive wastes, low-level metal wastes and ceramic high-level wastes that arise from the pyro-processing of PWR nuclear spent fuels are disposed of, has been developed. This program is ready both for a deterministic and probabilistic total system performance assessment which is able to evaluate nuclide release from the repository and farther transport into the geosphere and biosphere under various normal, disruptive natural and manmade events, and scenarios. The A-KRS has been deterministically assessed with 5 various normal and abnormal scenarios associated with nuclide release and transport in and around the repository. Dose exposure rates to the farming exposure group have been evaluated in accordance with all the scenarios and then compared among other.

Environmental program planning for the proposed high-level nuclear waste repository at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

1987-08-01

This report was prepared to illustrate the policy and actions that the State of Nevada believe are required to assure that the quality of the environment is adequately considered during the course of the DOE work at the proposed high-level nuclear waste repository at Yucca Mountain. The report describes the DOE environmental program and the studies planned by NWPO to reflect the State's position toward environmental protection. 41 refs., 2 figs., 11 tabs

Cost analysis of spent nuclear fuel management

International Nuclear Information System (INIS)

Robertson, D.L.M.; Ford, L.M.

1993-01-01

The Department of Energy Civilian Radioactive Waste Management System (CRWMS) is chartered to develop a waste management system for the safe disposal of spent nuclear fuel (SNF) from the 131 nuclear power reactors in the United States and a certain amount of high level waste (HLW) from reprocessing operations. The current schedule is to begin accepting SNF in 1998 for storage at a Monitored Retrievable Storage (MRS) facility. Subsequently, beginning in 2010, the system is scheduled to begin accepting SNF at a permanent geologic repository in 2010 and HLW in 2015. At this time, a MRS site has not been selected. Yucca Mountain, Nevada is currently being evaluated as the candidate site for the repository for permanent geologic disposal of SNF. All SNF, with the possible exception of the SNF from the western reactors, is currently planned to be shipped to or through the MRS site en route to the repository. The repository will operate in an acceptance and performance confirmation phase for a 50 year period beginning in 2010 with an additional nine year closure and five year decontamination and decommissioning period. The MRS has a statutory maximum capacity of 15,000 Metric Tons Uranium (MTU), with a further restriction that it may not store more than 10,000 MTU until the repository begins accepting waste. The repository is currently scheduled to store 63,000 MTU of SNF and an additional 7,000 MTU equivalent of HLW for a total capacity of 70,000 MTU. The amended act specified the MRS storage limits and identified Yucca Mountain as the only site to be characterized. Also, an Office of the Nuclear Waste Negotiator was established to secure a voluntary host site for the MRS. The MRS, the repository, and all waste containers/casks will go through a Nuclear Regulatory Commission licensing process much like the licensing process for a nuclear power plant. Environmental assessments and impact statements will be prepared for both the MRS and repository

Economic and fiscal impacts of large-scale development projects: implications for nuclear waste repositories

International Nuclear Information System (INIS)

Leistritz, F.L.; Murdock, S.H.; Texas A and M Univ., College Station)

1982-01-01

This paper deals with the local economic and fiscal implications of siting high-level nuclear waste repositories in rural areas. The economic and fiscal effects of repository development fall into two categories: (1) standard impacts similar to those that would be associated with developing any large-scale industrial facility in an isolated area; (2) special impacts that result from the hazardous nature of the nuclear materials stored and from federal ownership of the facility. Standard economic and fiscal impacts include employment effects (direct and secondary), local income changes, alterations in community price structures, effects on community services, and changes in revenues and costs for local jurisdictions. Special impacts include the possibility of diminished activity in other basic economic sectors, negative effects on the area's long-term growth prospects and a consequent dampening of investment in the local trade an service sectors, additional costs for local jurisdictions (e.g., for preparing evacuation plans), and limited local tax revenues resulting from the tax-exempt status of the facility. These special effects are difficult to quantify and require additional analysis. 47 references, 1 figure, 4 tables

Evaluation of alternative spent fuel waste package concepts for a repository in Basalt

International Nuclear Information System (INIS)

Hall, G.V.B.; Nair, B.R.

1986-01-01

The United States government has established a program for the disposal of spent nuclear fuel and high-level radioactive waste. The Nuclear Waste Policy Act (NWPA) of 1982 requires the first nuclear waste repository to begin receiving high-level radioactive waste in 1998. One of the potentially acceptable sites currently being evaluated is the Hanford Site in the Pasco Basin in the state of Washington where the host rock is basalt. Under the direction of the United States Department of Energy (DOE), Rockwell International's Rockwell Hanford Operations (RHO) has initiated the Basalt Waste Isolation Project (BWIP). The BWIP must design waste packages for emplacement in the repository. As part of the BWIP waste package development program, several alternative designs were considered for the disposal of spent nuclear fuel. This paper describes the concepts that were evaluated, the criteria that was developed for judging their relative merits, and the methodology that was employed. The results of the evaluation show that a Pipe-In-Tunnel design, which uses a long carbon steel pipe for the containment barrier for multiple packages of consolidated spent fuel, has the highest rating. Other designs which had high ratings are also discussed

Some reflections on human intrusion into a nuclear waste repository

International Nuclear Information System (INIS)

Westerlind, M.

2002-01-01

This paper summarises some of the Swedish nuclear regulators' requirements and views related to intrusion into a repository for spent nuclear fuel, in the post-closure phase. The focus is however on experiences from the interaction with various stakeholders in the Swedish process for siting a repository. It is recognised that intrusion is not a major concern but that it is regularly raised in the debate, often in connection with issues related to retrievability. It is pointed out that more attention should be paid to the repository performance after an intrusion event, both in safety assessments and in communication with stakeholders, and not only address the immediate impacts to intruders. It is believed that international co-operation would be useful for developing methodologies for defining intrusion scenarios. (author)

Will America's nuclear waste be laid to rest

Energy Technology Data Exchange (ETDEWEB)

Charles, D

1991-12-14

The Waste Isolation Pilot Plant (WIPP) in New Mexico, was designed to store waste from the United States (U.S.) nuclear weapons production in deep repositories under the naturally occurring salt beds. However no waste can be put into the repository until safety checks, designed as nuclear reactor safety standards, have been satisfactorily completed to the U.S. congress's satisfaction. While political controversy reigns the WIPP structure stands empty and steel drums of radioactive waste remain at the U.S. nuclear weapons factories. Proponents say costly capital investment is being wasted, opponents that people and the environment would be at risk of contamination if safety standards were not understood and adhered to. (UK).

Total system performance predictions (TSPA-1995) for the potential high-level waste repository at Yucca Mountain

International Nuclear Information System (INIS)

Sevougian, S.D.; Andrews, R.W.; McNeish, J.A.

1996-01-01

The management and operating contractor for the potential high-level nuclear waste repository at Yucca Mountain, Nevada, has been recently completed a new performance assessment of the ability of the repository to isolate and contain nuclear waste for long time periods (up to 1,000,000 years). Sensitivity analyses determine the most important physical parameters and processes, using the most current information and models

Assessment of crushed salt consolidation and fracture healing processes in a nuclear waste repository in salt

International Nuclear Information System (INIS)

1984-11-01

For a nuclear waste repository in salt, two aspects of salt behavior are expected to contribute to favorable conditions for waste isolation. First, consolidation of crushed salt backfill due to creep closure of the underground openings may result in a backfill barrier with low permeability. Second, fractures created in the salt by excavation may heal under the influence of stress and temperature following sealing. This report reviews the status of knowledge regarding crushed salt consolidation and fracture healing, provides analyses which predict the rates at which the processes will occur under repository conditions, and develops requirements for future study. Analyses of the rate at which crushed salt will consolidate are found to be uncertain because of unexplained wide variation in the creep properties of crushed salt obtained from laboratory testing, and because of uncertainties in predictions of long term closure rates of openings in salt. This uncertainty could be resolved to a large degree by additional laboratory testing of crushed salt. Similarly, additional testing of fracture healing processes is required to confirm that healing will be effective under repository conditions. Extensive references, 27 figures, 5 tables