WorldWideScience

Sample records for permanent behavior based

  1. Crystallization and atomic diffusion behavior of high coercive Ta/Nd-Fe-B/Ta-based permanent magnetic thin film

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Na; Zhang, Xiao; You, Caiyin; Fu, Huarui [Xi' an University of Technology, School of Materials Science and Engineering, Xi' an (China); Shen, Qianlong [Logistics University of People' s Armed Police Force, Tianjin (China)

    2017-06-15

    A high coercivity of about 20.4 kOe was obtained through post-annealing the sputtered Ta/Nd-Fe-B/Ta-based permanent magnetic thin films. Transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) analyses were performed to investigate the crystallization and atomic diffusion behaviors during post-annealing. The results show that the buffer and capping Ta layers prefered to intermix with Fe and B atoms, and Nd tends to be combined with O atoms. The preferred atomic combination caused the appearance of the soft magnetic phase of Fe-Ta-B, resulting in a kink of the second quadratic magnetic hysteresis loop. The preferred atomic diffusion and phase formation of the thin films were well explained in terms of the formation enthalpy of the various compounds. (orig.)

  2. Permanent magnet-based MRI

    Science.gov (United States)

    Cole, David Mitchell

    1997-10-01

    The principal goal of this project is to design and build a low-cost, imaging quality permanent magnet, together with the requisite shim, gradient, and radiofrequency coils, and to integrate the magnet with an existing imaging station. There are commercial products presently available that are very similar to this imager, but information about these products is proprietary. We present here all of the details concerning the design and the manufacturing process for constructing the permanent magnet, and include suggestions for improvement. Specifically, the prototype has a mass of about 150 kilograms and is therefore portable. It's C-type geometry allows maximum access to the imaging region, which is an oblate sphere about 0.5 inches in diameter centered in a 4.7 inch air gap between two seven-inch diameter polefaces. It is hoped that this imaging magnet will serve as the prototype for a series of larger versions that will be clinically useful and affordable to physicians in developing nations. To this end, scientists in the United States and Mexico have begun to collaborate with the intention to create an MRI institute in Mexico that will train new students in this discipline, and fabricate improved imagers. The prototype resulting from this work will seed the creation of this institute, and is intended to entice students into the study of MRI by enabling hands-on interaction with an otherwise prohibitively expensive instrument.

  3. Indentation Behavior of Permanently Densified Oxide Glasses

    DEFF Research Database (Denmark)

    Bechgaard, Tobias Kjær; Januchta, Kacper; Kapoor, Saurabh

    -induced changes in density, structure, and indentation behavior of a range of oxide glasses, including silicates, borates, and phosphates. The effect of compression on the structure is analyzed through both Raman and NMR spectroscopy, while the mechanical properties are investigated using Vickers micro......Hot isostatic compression can be used as a post treatment method to tune the properties of glass materials as well as to obtain improved understanding of the pressure-induced structural changes and densification mechanisms, e.g., during sharp contact loading. Here, we review the pressure......-indentation. The magnitude of the changes in all macroscopic properties (e.g., density, hardness, and crack resistance) is found to correlate well with the magnitude and type of structural change induced by hot compression. We show that the structural changes depend largely on the type of network former, the coordination...

  4. Permanent magnetic ferrite based power-tunable metamaterials

    Science.gov (United States)

    Zhang, Guanqiao; Lan, Chuwen; Gao, Rui; Zhou, Ji

    2017-08-01

    Power-tunable metamaterials based on barium permanent magnetic ferrite have been proposed and fabricated in this research. Scattering parameter measurements confirm a shift in resonant frequency in correlation to changes in incident electromagnetic power within microwave frequency band. The tunable phenomenon represented by a blue-shift in transmission spectra in the metamaterials array can be attributed to a decrease in saturation magnetization resulting from FMR-induced temperature elevation upon resonant conditions. This power-dependent behavior offers a simple and practical route towards dynamically fine-tunable ferrite metamaterials.

  5. Permanent magnet based dipole magnets for next generation light sources

    Directory of Open Access Journals (Sweden)

    Takahiro Watanabe

    2017-07-01

    Full Text Available We have developed permanent magnet based dipole magnets for the next generation light sources. Permanent magnets are advantageous over electromagnets in that they consume less power, are physically more compact, and there is a less risk of power supply failure. However, experience with electromagnets and permanent magnets in the field of accelerators shows that there are still challenges to replacing main magnets of accelerators for light sources with permanent magnets. These include the adjustability of the magnetic field, the temperature dependence of permanent magnets, and the issue of demagnetization. In this paper, we present a design for magnets for future light sources, supported by experimental and numerical results.

  6. Magnetic spring based on two permanent magnets

    International Nuclear Information System (INIS)

    Tsivilitsin, V.Yu.; Mil'man, Yu.V.; Goncharuk, V.A.; Bondar, I.B.

    2011-01-01

    A new type of the magnetic spring construction 'two permanent magnets' has been considered. A mathematical expression for the estimation of a pulling-in force has been offered. This expression is verified experimentally on the produced operating magnetic spring. The theoretical and experimental data are in good accordance. A number of advantages of the magnetic spring over the construction 'permanent magnet - magnetic circuit' such as an insignificant friction force between two magnets and a higher pulling force are discussed.

  7. Permanent magnetic ferrite based power-tunable metamaterials

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guanqiao; Lan, Chuwen [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Gao, Rui [High Temperature Thermochemistry Laboratory, Department of Mining and Materials Engineering, McGill University, Montreal, Quebec H3A 0C5 (Canada); Zhou, Ji, E-mail: zhouji@tsinghua.edu.cn [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2017-08-15

    Highlights: • Power-tunable metamaterials based on barium permanent magnetic ferrite have been proposed and fabricated. • It is observed that resonant frequency of the array shifts upon altering the output power. • This kind of power-tunable behavior is due to the temperature rise as a result of FMR-induced heat buildup. • This work offers a practical idea to tune ferrite metamaterials besides magneto-tunability and thermal-tunability. - Abstract: Power-tunable metamaterials based on barium permanent magnetic ferrite have been proposed and fabricated in this research. Scattering parameter measurements confirm a shift in resonant frequency in correlation to changes in incident electromagnetic power within microwave frequency band. The tunable phenomenon represented by a blue-shift in transmission spectra in the metamaterials array can be attributed to a decrease in saturation magnetization resulting from FMR-induced temperature elevation upon resonant conditions. This power-dependent behavior offers a simple and practical route towards dynamically fine-tunable ferrite metamaterials.

  8. Permanent deformation behavior of naturally occurring bituminous sands

    CSIR Research Space (South Africa)

    Anochie-Boateng, Joseph

    2008-01-01

    Full Text Available and mining equipment at two different load pulse durations or loading frequencies (related to field-trafficking speeds). Both the test data and axial permanent strain models developed in the form of power functions of the number of repeated load applications...

  9. Grain Refinement of Permanent Mold Cast Copper Base Alloys

    Energy Technology Data Exchange (ETDEWEB)

    M.Sadayappan; J.P.Thomson; M.Elboujdaini; G.Ping Gu; M. Sahoo

    2005-04-01

    Grain refinement is a well established process for many cast and wrought alloys. The mechanical properties of various alloys could be enhanced by reducing the grain size. Refinement is also known to improve casting characteristics such as fluidity and hot tearing. Grain refinement of copper-base alloys is not widely used, especially in sand casting process. However, in permanent mold casting of copper alloys it is now common to use grain refinement to counteract the problem of severe hot tearing which also improves the pressure tightness of plumbing components. The mechanism of grain refinement in copper-base alloys is not well understood. The issues to be studied include the effect of minor alloy additions on the microstructure, their interaction with the grain refiner, effect of cooling rate, and loss of grain refinement (fading). In this investigation, efforts were made to explore and understand grain refinement of copper alloys, especially in permanent mold casting conditions.

  10. A rotary permanent magnet magnetic refrigerator based on AMR cycle

    International Nuclear Information System (INIS)

    Aprea, C.; Cardillo, G.; Greco, A.; Maiorino, A.; Masselli, C.

    2016-01-01

    Magnetic refrigeration is an emerging, environment-friendly technology based on a magnetic solid that acts as a refrigerant by magneto-caloric effect (MCE). The reference cycle for magnetic refrigeration is AMR (Active Magnetic Regenerative refrigeration). In order to demonstrate the potential of magnetic refrigeration to provide useful cooling in the near room temperature range, a novel Rotary Permanent Magnet Magnetic Refrigerator (RPMMR) is described in this paper. Gadolinium has been selected as magnetic refrigerant and demineralized water has been employed as regenerating fluid. The total mass of gadolinium (1.20 kg), shaped as packed bed spheres, is housed in 8 regenerators. A magnetic system, based on a double U configuration of permanent magnets, provides a magnetic flux density of 1.25 T with an air gap of 43 mm. A rotary vane pump forces the regenerating fluid through the regenerators. The operational principle of the magnetic refrigerator and initial experimental results are reported and analyzed.

  11. Study of Magnetic Properties on the Corrosion Behavior and Influence of Temperature in Permanent Magnet (Nd-Fe-B) Used in PMSM

    OpenAIRE

    N. Yogal; C. Lehrmann

    2014-01-01

    The use of permanent magnets (PM) is increasing in permanent magnet synchronous machines (PMSM) to fulfill the requirements of high efficiency machines in modern industry. PMSM are widely used in industrial applications, wind power plants and the automotive industry. Since PMSM are used in different environmental conditions, the long-term effect of NdFeB-based magnets at high temperatures and their corrosion behavior have to be studied due to the irreversible loss of magn...

  12. The dynamic behavior of magnetic fluid adsorbed to small permanent magnet in alternating magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Sudo, Seiichi, E-mail: sudo@akita-pu.ac.j [Faculty of Systems Science and Technology, Akita Prefectural University, Ebinokuchi 84-4, Yurihonjo 015-0055 (Japan); Asano, Daisaku [Faculty of Systems Science and Technology, Akita Prefectural University, Ebinokuchi 84-4, Yurihonjo 015-0055 (Japan); Takana, Hidemasa; Nishiyama, Hideya [Institute of Fluid Science, Tohoku University, Katahira 2-1-1, Aobaku, Sendai 980-8577 (Japan)

    2011-05-15

    The dynamic behavior of a magnetic fluid adsorbed to a small NdFeB permanent magnet subjected to an alternating magnetic field was studied with a high speed video camera system. The directions of alternating magnetic field are parallel and opposite to that of the permanent magnet. It was found that the surface of magnetic fluid responds to the external alternating magnetic field in elongation and contraction with a lot of spikes. Generation of a capillary magnetic fluid jet was observed in the neighbourhood of a specific frequency of alternating field. The effect of gravitational force on surface phenomena of magnetic fluid adsorbed to the permanent magnet was revealed. - Research Highlights: Magnetic fluid of the system responds to alternating magnetic field with higher frequencies. Large-amplitude surface motions of magnetic fluid occur at the specific frequencies of the external field. Capillary jets of magnetic fluid are generated at the natural frequency of the system.

  13. The electromagnetic design of a permanent magnet based separator

    International Nuclear Information System (INIS)

    Nedelcu, S.

    2002-08-01

    The aim of this work was to design a permanent magnet based device that can selectively transport paramagnetic particles. Using specialised electromagnetic design software various arrangements of permanent magnets have been investigated. Each test geometry had to be constructively simple and able to produce highly non-uniform magnetic fields before being considered further in any more detail. The main parameter to indicate that the test geometry might be a suitable device has been ascribed to the ratio η between the highest (ON) and lowest (OFF) magnetic fields that were measured. A linear arrangement of permanent magnets has been considered first. This device produced a ratio η ∼ 2. Further, the cylindrical and the tubular arrangements may be considered as substantial improvements over the first geometry. The OFF magnetic fields have been substantially reduced by the method of magnetic shielding. Intensive research and modelling has been spent on addressing the problem of finding the optimal geometry for such arrangements. An experimental system has been also built, and the experimental values were compared against the theory. However, the results produced evidence that the manufacturing of any improved geometry (an estimated η ∼ 100) in this direction might be very difficult, for the tolerances involved were very strict. The disk arrangement was the latest device to be investigated. Particularly, a magnetic dipole model developed earlier for the ring arrangement suggested the way in which to arrange the magnets in the ON position. Moreover, the use of the magnetic symmetry of the device forced the OFF magnetic fields to negligible values. Detailed computer simulations of the dynamics of the particles in the applied magnetic field of the tubular and disk arrangements have been earned out. The adopted models could show realistic phenomena, e.g. particle clustering, chaining, block movement, etc. The separation efficiency proved to be nearly 100%. For the

  14. New developments in NdFeB-based permanent magnets

    International Nuclear Information System (INIS)

    Liu, Z.W.

    2011-01-01

    NdFeB based alloys have been used as permanent magnets for almost thirty years. The recent researches aim at optimizing the composition, microstructure and properties, reducing cost, and developing new processes. The demand for sintered magnet is increasing. Efforts are directed towards improving properties by controlling grain boundary diffusion, minimizing the rare earth (RE) content and also improving production yield. As for bonded magnets, to enhance remanence and energy product, nanocrystalline powders are employed. High thermal stability has been realized by mixing NdFeB with hard ferrite powders. For nanocrystalline and nano composite NdFeB based alloys, both compositional modification and microstructural optimization have been carried out. New approaches have also been proposed to prepare NdFeB magnets with idea structure. Surfactant assisted ball milling is a good top-down method to obtain nano sized hard magnetic particles and anisotropic nano flakes. Synthesis of NdFeB nanoparticles and NdFeB/Fe (Co) nano composite powders by bottom-up techniques, such as chemical reduction process and co-precipitation, has been successful very recently. To assemble nanocrystalline NdFeB powders or nanoparticles into bulk magnets, various novel consolidation processes including spark plasma sintering and high velocity press have been employed. Hot deformation can be selected as the process to achieve anisotropy in nanocrystalline magnets. (author)

  15. Rate-based structural health monitoring using permanently installed sensors

    Science.gov (United States)

    Corcoran, Joseph

    2017-09-01

    Permanently installed sensors are becoming increasingly ubiquitous, facilitating very frequent in situ measurements and consequently improved monitoring of `trends' in the observed system behaviour. It is proposed that this newly available data may be used to provide prior warning and forecasting of critical events, particularly system failure. Numerous damage mechanisms are examples of positive feedback; they are `self-accelerating' with an increasing rate of damage towards failure. The positive feedback leads to a common time-response behaviour which may be described by an empirical relation allowing prediction of the time to criticality. This study focuses on Structural Health Monitoring of engineering components; failure times are projected well in advance of failure for fatigue, creep crack growth and volumetric creep damage experiments. The proposed methodology provides a widely applicable framework for using newly available near-continuous data from permanently installed sensors to predict time until failure in a range of application areas including engineering, geophysics and medicine.

  16. Impact of the Superpave hot mix asphalt properties on its permanent deformation behavior

    Directory of Open Access Journals (Sweden)

    Qasim Zahra

    2018-01-01

    Full Text Available In Iraq, the severity of rutting has increased in asphalt pavements possibly due to the increase in truck axle loads, tyre pressure, and high pavement temperature in summer. As of late, Superpave has been accounted as an enhanced system for performance based design, analysis of asphalt pavement performance prediction for asphalt concrete mixes. In this research the development of permanent deformation in asphalt concrete under repeated loadings was investigated, Wheel-Tracking apparatus has been used in a factorial testing program during which 44 slab samples were tested to simulate actual pavement. The objectives of the present research include; investigating the main factors affecting rutting in asphalt concrete mixture, quantifying the effect of SBS polymer and steel reinforcement on asphalt concrete mixtures in addition to studying the effect of variables on the asphalt concrete mixes against moisture sensitivity. It has been determined that that increasing of compaction temperature from 110 to 150°C will decrease the permanent deformation by 20.5 and 15.6 percent for coarse and fine gradation control asphalt mixtures, respectively. While the permanent deformation decreases by 21.3 percent when the compaction temperature is increased from 110 to 150°C for coarse gradation SBS modified asphalt mixtures.

  17. DSP Based Direct Torque Control of Permanent Magnet Synchronous Motor (PMSM) using Space Vector Modulation (DTC-SVM)

    DEFF Research Database (Denmark)

    Swierczynski, Dariusz; Kazmierkowski, Marian P.; Blaabjerg, Frede

    2002-01-01

    DSP Based Direct Torque Control of Permanent Magnet Synchronous Motor (PMSM) using Space Vector Modulation (DTC-SVM)......DSP Based Direct Torque Control of Permanent Magnet Synchronous Motor (PMSM) using Space Vector Modulation (DTC-SVM)...

  18. ACCUMULATED DEFORMATION MODELING OF PERMANENT WAY BASED ON ENTROPY SYSTEM

    Directory of Open Access Journals (Sweden)

    D. M. Kurhan

    2015-07-01

    Full Text Available Purpose. The work provides a theoretical research about the possibility of using methods that determine the lifetime of a railway track not only in terms of total stresses, and accounting its structure and dynamic characteristics. The aim of these studies is creation the model of deformations accumulation for assessment of service life of a railway track taking into account these features. Methodology. To simulate a gradual change state during the operation (accumulation of deformations the railway track is presented as a system that consists of many particles of different materials collected in a coherent design. It is appropriate to speak not about the appearance of deformations of a certain size in a certain section of the track, and the probability of such event on the site. If to operate the probability of occurrence of deviations, comfortable state of the system is characterized by the number of breaks of the conditional internal connections. The same state of the system may correspond to different combinations of breaks. The more breaks, the more the number of options changes in the structure of the system appropriate to its current state. Such a process can be represented as a gradual transition from an ordered state to a chaotic one. To describe the characteristics of the system used the numerical value of the entropy. Findings. Its entropy is constantly increasing at system aging. The growth of entropy is expressed by changes in the internal energy of the system, which can be determined using mechanical work forces, which leads to deformation. This gives the opportunity to show quantitative indication of breaking the bonds in the system as a consequence of performing mechanical work. According to the results of theoretical research methods for estimation of the timing of life cycles of railway operation considering such factors as the structure of the flow of trains, construction of the permanent way, the movement of trains at high

  19. Modeling of hysteretic behavior of the levitation force between superconductor and permanent magnet

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Xing-da, E-mail: shuxdw@gmail.com [School of Information Engineering, Guangdong Medical College, No. 2, Eastern Wenming Road, Zhanjiang 524023 (China); Xu, Ke-Xi, E-mail: kxxu@staff.shu.edu.cn [Department of Physics, Shanghai University, Shanghai 200444 (China); Cao, Yue; Hu, Shun-bo; Zuo, Peng-xiang; Li, Guan-dong [Department of Physics, Shanghai University, Shanghai 200444 (China)

    2013-03-15

    Highlights: ► Experimental results on hysteretic behavior of the levitaion force are presented. ► Hysteresis loop for the first descent/ascent cycle of magnet is largest. ► Hysteresis loop for the second and subsequent cycles almost overlap each other. ► Yang’s frozen-image model cannot describe this characteristic of levitation force. ► An updated frozen-image model is developed to describe these experimental results. -- Abstract: The hysteretic behavior of the levitation force between a permanent magnet and a melt-textured-growth YBCO bulk has been investigated under both zero-field cooling (ZFC) and field cooling (FC) processes. It is found that both in ZFC and FC measurements, the hysteresis loop for the first descent/ascent cycle of magnet is relatively larger than that for the second or third cycle, and the hysteresis loops for Cycle 2–4 have the same area. These results can be qualitatively understood in terms of the critical state model. To describe these experimental results, we develop an updated frozen-image model, which is obtained by modifying the change rules of the vertical movement image in the advanced frozen-image model proposed by Yang et al. Comparing with the advanced frozen-image model proposed by Yang et al., our model cannot only give the hysteretic characteristic in the first descent–ascent cycle of magnet, but also show the hysteresis loops with the same area for the second and subsequent cycles.

  20. COMPARATIVE ANALYSIS OF THE BEHAVIOR OF COAXIAL AND FRONTAL COUPLINGS – WITH PERMANENT MAGNETS – IN HIGH TEMPERATURE ENVIRONMENTS

    Directory of Open Access Journals (Sweden)

    Marcel Oanca

    2004-12-01

    Full Text Available This paper presents a comparative analysis of the behavior of coaxial and frontal couplings – with permanent magnets – in high temperature environments specific to iron and steel industry. The comparative analysis is made at the level of the specific forces developed in the most difficult environments. The maximum temperature was limited for reasons of thermal stability of the Nd-Fe-B permanent magnets. In this context it was studied, by the help of the PDE-ase soft that uses the finite element method, the way magnetic induction modifies, the specific forces developed and the distribution of temperature within the coaxial and frontal couplers with permanent magnets, for variations of the distance between the magnets (air gap within the limits 2-20 mm.

  1. Evaluation of parameter sensitivities for flux-switching permanent magnet machines based on simplified equivalent magnetic circuit

    Directory of Open Access Journals (Sweden)

    Gan Zhang

    2017-05-01

    Full Text Available Most of the published papers regarding the design of flux-switching permanent magnet machines are focused on the analysis and optimization of electromagnetic or mechanical behaviors, however, the evaluate of the parameter sensitivities have not been covered, which contrarily, is the main contribution of this paper. Based on the finite element analysis (FEA and simplified equivalent magnetic circuit, the method proposed in this paper enables the influences of parameters on the electromagnetic performances, i.e. the parameter sensitivities, to be given by equations. The FEA results are also validated by experimental measurements.

  2. An accurate interference refractometer based on a permanent vacuum chamber : development and results

    NARCIS (Netherlands)

    Renkens, M.J.M.; Schellekens, P.H.J.

    1993-01-01

    A new accurate interference refractometer, without pumping device, has been developed. The refractometer is based on a commercially available laser measurement system and uses a prismatic measuring cell, containing a permanent vacuum chamber. Measurements of the refractive index of air can be

  3. Grain refinement of permanent mold cast copper base alloys. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M.

    2004-04-29

    Grain refinement behavior of copper alloys cast in permanent molds was investigated. This is one of the least studied subjects in copper alloy castings. Grain refinement is not widely practiced for leaded copper alloys cast in sand molds. Aluminum bronzes and high strength yellow brasses, cast in sand and permanent molds, were usually fine grained due to the presence of more than 2% iron. Grain refinement of the most common permanent mold casting alloys, leaded yellow brass and its lead-free replacement EnviroBrass III, is not universally accepted due to the perceived problem of hard spots in finished castings and for the same reason these alloys contain very low amounts of iron. The yellow brasses and Cu-Si alloys are gaining popularity in North America due to their low lead content and amenability for permanent mold casting. These alloys are prone to hot tearing in permanent mold casting. Grain refinement is one of the solutions for reducing this problem. However, to use this technique it is necessary to understand the mechanism of grain refinement and other issues involved in the process. The following issues were studied during this three year project funded by the US Department of Energy and the copper casting industry: (1) Effect of alloying additions on the grain size of Cu-Zn alloys and their interaction with grain refiners; (2) Effect of two grain refining elements, boron and zirconium, on the grain size of four copper alloys, yellow brass, EnviroBrass II, silicon brass and silicon bronze and the duration of their effect (fading); (3) Prediction of grain refinement using cooling curve analysis and use of this method as an on-line quality control tool; (4) Hard spot formation in yellow brass and EnviroBrass due to grain refinement; (5) Corrosion resistance of the grain refined alloys; (6) Transfer the technology to permanent mold casting foundries; It was found that alloying elements such as tin and zinc do not change the grain size of Cu-Zn alloys

  4. The TGT Estimation of the Social Behavior Characteristics for Permanent Resident around NPPs in KOREA

    International Nuclear Information System (INIS)

    Bang, Sun-Young; Lee, Gab-Bock; Chung, Yang-Geun

    2006-01-01

    The most strong protection method of radiation emergency preparedness is the evacuation when a great deal of radionuclide materials is released to environment. NRC(Nuclear Regulation Committee) made the evacuation time estimation to be necessary condition of emergency plan as the basis technology through the NUREG-0654 and has performed the research of the evacuation using traffic analysis continuously. In KOREA, The Notice 2004-11 of Ministry of Science and Technology nuclear enterprise must estimate evacuation time through the consultation with local autonomous entities and the result of the consultation must be appended in emergency plan. But evacuation estimation method in KOREA was based on simple assumption which did not consider evacuation characteristics and traffic analysis; therefore it could not reflect actual accident adequately. Besides technical aspect, the characteristics of personal and social behavior must be considered in evaluation of the evacuation time. These characteristics of behavior emerged in the research of natural and human disaster rather than nuclear accident which has little experience. So, the characteristics of personal and social behavior must be considered in evacuation time estimation

  5. Lawful Permanent Residents Fiscal Year 2015 Core Based Statistical Area (CBSA) of Residence

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  6. Lawful Permanent Residents Fiscal Year 2011 Core Based Statistical Area (CBSA) of Residence

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  7. Lawful Permanent Residents Fiscal Year 2014 Core Based Statistical Area (CBSA) of Residence

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  8. Repeated Load Permanent Deformation Behavior of Mixes With and Wihtout Modified Bituments

    Directory of Open Access Journals (Sweden)

    Imran Hafeez

    2011-01-01

    Full Text Available Premature rutting in flexible pavement structure is being observed on most of the road network of Pakistan. It initiates primarily due to uncontrolled axle loading and high ambient temperatures. NHA (National Highway Authority, Pakistan has continuously been modifying aggregate gradations and penetration grade of bitumen, without any prior investigation of the mix behaviour under the prevailing axle load and environmental conditions of the country. A comprehensive laboratory investigation was carried out on six mixes ranging from finer to coarser. Specimens were subjected to cyclic loading on UTM-5P (Universal Testing Machine to study the resistance against permanent deformation of the mixes at 25, 40 and 550C. At low temperatures and stress levels, both coarse and fine graded mixes showed less accumulated strain, whereas at higher temperatures and stress levels, coarse graded mix with PMB (Polymer Modified Bitumen showed good resistance to permanent deformation.

  9. Search behavior in various breeds of adult dogs (Canis familiaris): object permanence and olfactory cues.

    Science.gov (United States)

    Gagnon, S; Doré, F Y

    1992-03-01

    Human analog tests of object permanence were administered to various breeds of adult dogs (Canis familiaris). Experiment 1 showed that the performance of terriers, sporting, and working dogs did not differ. Dogs succeeded in solving invisible displacement problems, but performance was lower than in visible displacement tests. Familiarity with the task had some influence because invisible displacement tests were more successful if they were preceded by visible displacement tests. In Experiment 2, odor cues from the target object and the hiding screens were available or were masked. Results confirmed that success was lower in invisible than in visible displacement tests and that these problems were solved on the basis of representation of visual information rather than on the basis of olfactory cues or of local rule learning. Dogs are compared with other species that display Stage 6 object permanence.

  10. A current controlled matrix converter for wind energy conversion systems based on permanent magnet synchronous generator

    OpenAIRE

    Naggar H. Saad; Ahmed A. El-Sattar; Mohamed I. Marei

    2016-01-01

    The main challenges of wind energy conversion systems (WECS) are to maximize the energy capture from the wind and injecting reactive power during the fault. This paper presents a current controlled matrix converter to interface Permanent Magnet Synchronous Generators (PMSG) based WECS with the grid. To achieve fast dynamic response with reduced current ripples, a hysteresis current control is utilized. The proposed control system decouples the active and reactive components of the PMSG curren...

  11. Analysis and design of permanent magnet biased magnetic bearing based on hybrid factor

    Directory of Open Access Journals (Sweden)

    Jinji Sun

    2016-03-01

    Full Text Available In this article, hybrid factor is proposed for hybrid magnetic bearing. The hybrid factor is defined as the ratio of the force produced by the permanent magnet and the forces produced by the permanent magnet and current in hybrid magnetic bearing. It is deduced from a certain radial hybrid magnetic bearing using its important parameters such as the current stiffness and displacement stiffness at first and then the dynamic model of magnetically suspended rotor system is established. The relationship between structural parameters and control system parameters is analyzed based on the hybrid factor. Some influencing factors of hybrid factor in hybrid magnetic bearing, such as the size of the permanent magnet, length of air gap, and area of the stator poles, are analyzed in this article. It can be concluded that larger hybrid factor can be caused by the smaller power loss according to the definition of hybrid factor mentioned above. Meanwhile, the hybrid factor has a maximum value, which is related to control system parameters such as proportional factor expect for structural parameters. Finally, the design steps of parameters of hybrid magnetic bearing can be concluded.

  12. Design and development of permanent magnet based focusing lens for J-Band Klystron

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Kumud; Itteera, Janvin; Ukarde, Priti; Malhotra, Sanjay; Taly, Y.K., E-mail: kumuds@barc.gov.in [Control Instrumentation Division, Bhabha Atomic Research Centre, Mumbai (India); Bandyopadhay, Ayan; Meena, Rakesh; Rawat, Vikram; Joshi, L.M [Microwave Tubes Division, Central Electronics Engineering Research Institute, Pilani (India)

    2014-07-01

    Applying permanent magnet technology to beam focusing in klystrons can reduce their power consumption and increase their reliability of operation. Electromagnetic design of the beam focusing elements, for high frequency travelling wave tubes, is very critical. The magnitude and profile of the magnetic field need to match the optics requirement from beam dynamics studies. The rise of the field from cathode gun region to the uniform field region (RF section) is important as the desired transition from zero to peak axial field must occur over a short axial distance. Confined flow regime is an optimum choice to minimize beam scalloping but demands an axial magnetic field greater than 2 - 3 times the Brillouin flow field. This necessitates optimization in the magnet design achieve high magnetic field within given spatial constraints. Electromagnetic design and simulations were done using 3D Finite element method (FEM) analysis software. A permanent magnet based focusing lens for a miniature J-Band klystron has been designed and developed at Control Instrumentation Division, BARC. This paper presents the design, simulation studies, beam transmission and RF tests results for J Band klystron with permanent magnet focusing lens. (author)

  13. A chiral-based magnetic memory device without a permanent magnet.

    Science.gov (United States)

    Ben Dor, Oren; Yochelis, Shira; Mathew, Shinto P; Naaman, Ron; Paltiel, Yossi

    2013-01-01

    Several technologies are currently in use for computer memory devices. However, there is a need for a universal memory device that has high density, high speed and low power requirements. To this end, various types of magnetic-based technologies with a permanent magnet have been proposed. Recent charge-transfer studies indicate that chiral molecules act as an efficient spin filter. Here we utilize this effect to achieve a proof of concept for a new type of chiral-based magnetic-based Si-compatible universal memory device without a permanent magnet. More specifically, we use spin-selective charge transfer through a self-assembled monolayer of polyalanine to magnetize a Ni layer. This magnitude of magnetization corresponds to applying an external magnetic field of 0.4 T to the Ni layer. The readout is achieved using low currents. The presented technology has the potential to overcome the limitations of other magnetic-based memory technologies to allow fabricating inexpensive, high-density universal memory-on-chip devices.

  14. Sliding observer-based demagnetisation fault-tolerant control in permanent magnet synchronous motors

    Directory of Open Access Journals (Sweden)

    Changfan Zhang

    2017-04-01

    Full Text Available This study proposes a fault-tolerant control method for permanent magnet synchronous motors (PMSMs based on the active flux linkage concept, which addresses permanent magnet (PM demagnetisation faults in PMSMs. First, a mathematical model for a PMSM is established based on active flux linkage, and then the effect of PM demagnetisation on the PMSM is analysed. Second, the stator current in the static coordinate is set as the state variable, an observer is designed based on a sliding-mode variable structure, and an equation for active flux linkage is established for dynamic estimation based on the equivalent control principle of sliding-mode variable structure. Finally, the active flux linkage for the next moment is predicted according to the operating conditions of the motor and the observed values of the current active flux linkage. The deadbeat control strategy is applied to eliminate errors in the active flux linkage and realise the objective of fault-tolerant control. A timely and effective control for demagnetisation faults is achieved using the proposed method, which validity and feasibility are verified by the simulation and experiment results.

  15. Controlling chaos in permanent magnet synchronous motor based on finite-time stability theory

    International Nuclear Information System (INIS)

    Du-Qu, Wei; Bo, Zhang

    2009-01-01

    This paper reports that the performance of permanent magnet synchronous motor (PMSM) degrades due to chaos when its systemic parameters fall into a certain area. To control the undesirable chaos in PMSM, a nonlinear controller, which is simple and easy to be constructed, is presented to achieve finite-time chaos control based on the finite-time stability theory. Computer simulation results show that the proposed controller is very effective. The obtained results may help to maintain the industrial servo driven system's security operation. (general)

  16. Taking good care of myself: a qualitative study on self-care behavior among Chinese persons with a permanent colostomy.

    Science.gov (United States)

    Tao, Hui; Songwathana, Praneed; Isaramalai, Sang-arun; Wang, Qingxi

    2014-12-01

    In Chinese culture, as a possible consequence of Confucianism, caring for the sick is considered a moral obligation of family members, while self-care is only the basis of fulfilling filial piety. This qualitative study aims to explore the self-care behavior among persons with a permanent colostomy in a Chinese cultural context of emphasizing the role of family caregiving. Data from in-depth interviews with seven Chinese adults at a university hospital in southwest China were analyzed using content analysis. Informants' self-care behavior was characterized by "taking good care of myself," which underlined individuals' efforts to manage colostomy-related impacts involving: (i) taking care of my colostomy with a proper degree of independence; (ii) taking care of my life by dealing with limitations; (iii) taking care of my mood in a positive way. Findings revealed that informants' self-care behavior was linked to their Confucian beliefs in family obligations, and also influenced by a happy-go-lucky outlook of life, a likely product of Taoism. The information is useful for nurses to design a culturally appropriate care plan to improve self-care behavior and proper family caregiving. © 2014 Wiley Publishing Asia Pty Ltd.

  17. Lawful Permanent Residents Fiscal Year 2016 Core Based Statistical Area (CBSA) of Residence

    Data.gov (United States)

    Department of Homeland Security — Lawful permanet residents (LPRs) are foreign nationals who have been gratned the right to reside permanently in the United States. LPRs are also known as 'permanent...

  18. Behavioral based safety approaches

    International Nuclear Information System (INIS)

    Maria Michael Raj, I.

    2009-01-01

    Approach towards the establishment of positive safety culture at Heavy Water Plant, Tuticorin includes the adoption of several important methodologies focused on human behavior and culminates with achievement of Total Safety Culture where Quality and Productivity are integrated with Safety

  19. Nonlinear vibration behaviors of high-Tc superconducting bulks in an applied permanent magnetic array field

    Science.gov (United States)

    Li, Jipeng; Li, Haitao; Zheng, Jun; Zheng, Botian; Huang, Huan; Deng, Zigang

    2017-06-01

    The nonlinear vibration of high temperature superconducting (HTS) bulks in an applied permanent magnetic array (Halbach array) field, as a precondition for commercial application to HTS maglev train and HTS bearing, is systematically investigated. This article reports the actual vibration rules of HTS bulks from three aspects. First, we propose a new numerical model to simplify the calculation of levitation force. This model could provide precise simulations, especially the estimation of eigenfrequency. Second, an approximate analytic solution of the vibration of the HTS bulks is obtained by using the method of harmonic balance. Finally, to verify the results mentioned above, we measure the vertical vibration acceleration signals of an HTS maglev model, consisting of eight YBaCuO bulks, oscillating freely above a Halbach array with large displacement excitation. Higher order harmonic components, which indicate the nonlinear vibration phenomenon, are detected in the responses. All the three results are compared and agreed well with each other. This study combines the experimental and theoretical analyses and provides a deep understanding of the physical phenomenon of the nonlinear vibration and is meaningful for the vibration control of the relevant applications.

  20. Adaptive PIF control for permanent magnet synchronous motors based on GPC.

    Science.gov (United States)

    Lu, Shaowu; Tang, Xiaoqi; Song, Bao

    2012-12-24

    To enhance the control performance of permanent magnet synchronous motors (PMSMs), a generalized predictive control (GPC)-based proportional integral feedforward (PIF) controller is proposed for the speed control system. In this new approach, firstly, based on the online identification of controlled model parameters, a simplified GPC law supplies the PIF controller with suitable control parameters according to the uncertainties in the operating conditions. Secondly, the speed reference curve for PMSMs is usually required to be continuous and continuously differentiable according to the general servo system design requirements, so the adaptation of the speed reference is discussed in details in this paper. Hence, the performance of the speed control system using a GPC-based PIF controller is improved for tracking some specified signals. The main motivation of this paper is the extension of GPC law to replace the traditional PI or PIF controllers in industrial applications. The efficacy and usefulness of the proposed controller are verified through experimental results.

  1. Histone deacetylation during brain development is essential for permanent masculinization of sexual behavior.

    Science.gov (United States)

    Matsuda, Ken Ichi; Mori, Hiroko; Nugent, Bridget M; Pfaff, Donald W; McCarthy, Margaret M; Kawata, Mitsuhiro

    2011-07-01

    Epigenetic histone modifications are emerging as important mechanisms for conveyance of and maintenance of effects of the hormonal milieu to the developing brain. We hypothesized that alteration of histone acetylation status early in development by sex steroid hormones is important for sexual differentiation of the brain. It was found that during the critical period for sexual differentiation, histones associated with promoters of essential genes in masculinization of the brain (estrogen receptor α and aromatase) in the medial preoptic area, an area necessary for male sexual behavior, were differentially acetylated between the sexes. Consistent with these findings, binding of histone deacetylase (HDAC) 2 and 4 to the promoters was higher in males than in females. To examine the involvement of histone deacetylation on masculinization of the brain at the behavioral level, we inhibited HDAC in vivo by intracerebroventricular infusion of the HDAC inhibitor trichostatin A or antisense oligodeoxynucleotide directed against the mRNA for HDAC2 and -4 in newborn male rats. Aspects of male sexual behavior in adulthood were significantly reduced by administration of either trichostatin A or antisense oligodeoxynucleotide. These results demonstrate that HDAC activity during the early postnatal period plays a crucial role in the masculinization of the brain via modifications of histone acetylation status.

  2. Current error vector based prediction control of the section winding permanent magnet linear synchronous motor

    Energy Technology Data Exchange (ETDEWEB)

    Hong Junjie, E-mail: hongjjie@mail.sysu.edu.cn [School of Engineering, Sun Yat-Sen University, Guangzhou 510006 (China); Li Liyi, E-mail: liliyi@hit.edu.cn [Dept. Electrical Engineering, Harbin Institute of Technology, Harbin 150000 (China); Zong Zhijian; Liu Zhongtu [School of Engineering, Sun Yat-Sen University, Guangzhou 510006 (China)

    2011-10-15

    Highlights: {yields} The structure of the permanent magnet linear synchronous motor (SW-PMLSM) is new. {yields} A new current control method CEVPC is employed in this motor. {yields} The sectional power supply method is different to the others and effective. {yields} The performance gets worse with voltage and current limitations. - Abstract: To include features such as greater thrust density, higher efficiency without reducing the thrust stability, this paper proposes a section winding permanent magnet linear synchronous motor (SW-PMLSM), whose iron core is continuous, whereas winding is divided. The discrete system model of the motor is derived. With the definition of the current error vector and selection of the value function, the theory of the current error vector based prediction control (CEVPC) for the motor currents is explained clearly. According to the winding section feature, the motion region of the mover is divided into five zones, in which the implementation of the current predictive control method is proposed. Finally, the experimental platform is constructed and experiments are carried out. The results show: the current control effect has good dynamic response, and the thrust on the mover remains constant basically.

  3. Magnetic Field Equivalent Current Analysis-Based Radial Force Control for Bearingless Permanent Magnet Synchronous Motors

    Directory of Open Access Journals (Sweden)

    Huangqiu Zhu

    2015-05-01

    Full Text Available Bearingless permanent magnet synchronous motors (BPMSMs, with all advantages of permanent magnet motors (PMSMs and magnetic bearings, have become an important research direction in the bearingless motor field. To realize a stable suspension for the BPMSM, accurate decoupling control between the electromagnetic torque and radial suspension force is indispensable. In this paper, a concise and reliable analysis method based on a magnetic field equivalent current is presented. By this analysis method, the operation principle is analyzed theoretically, and the necessary conditions to produce a stable radial suspension force are confirmed. In addition, mathematical models of the torque and radial suspension force are established which is verified by the finite element analysis (FEA software ANSYS. Finally, an experimental prototype of a 2-4 poles surface-mounted BPMSM is tested with the customized control strategy. The simulation and experimental results have shown that the motor has good rotation and suspension performance, and validated the accuracy of the proposed analysis method and the feasibility of the control strategy.

  4. On the role of the grain size in the magnetic behavior of sintered permanent magnets

    Science.gov (United States)

    Efthimiadis, K. G.; Ntallis, N.

    2018-02-01

    In this work the finite elements method is used to simulate, by micromagnetic modeling, the magnetic behavior of sintered anisotropic magnets. Hysteresis loops were simulated for different grain sizes in an oriented multigrain sample. By keeping out other parameters that contribute to the magnetic microstructure, such as the sample size, the grain morphology and the grain boundaries mismatch, it has been found that the grain size affects the magnetic properties only if the grains are exchange-decoupled. In this case, as the grain size decreases, a decrease in the nucleation field of a reverse magnetic domain is observed and an increase in the coercive field due to the pinning of the magnetic domain walls at the grain boundaries.

  5. Neural network-based adaptive dynamic surface control for permanent magnet synchronous motors.

    Science.gov (United States)

    Yu, Jinpeng; Shi, Peng; Dong, Wenjie; Chen, Bing; Lin, Chong

    2015-03-01

    This brief considers the problem of neural networks (NNs)-based adaptive dynamic surface control (DSC) for permanent magnet synchronous motors (PMSMs) with parameter uncertainties and load torque disturbance. First, NNs are used to approximate the unknown and nonlinear functions of PMSM drive system and a novel adaptive DSC is constructed to avoid the explosion of complexity in the backstepping design. Next, under the proposed adaptive neural DSC, the number of adaptive parameters required is reduced to only one, and the designed neural controllers structure is much simpler than some existing results in literature, which can guarantee that the tracking error converges to a small neighborhood of the origin. Then, simulations are given to illustrate the effectiveness and potential of the new design technique.

  6. Approximation-Based Discrete-Time Adaptive Position Tracking Control for Interior Permanent Magnet Synchronous Motors.

    Science.gov (United States)

    Yu, Jinpeng; Shi, Peng; Yu, Haisheng; Chen, Bing; Lin, Chong

    2015-07-01

    This paper considers the problem of discrete-time adaptive position tracking control for a interior permanent magnet synchronous motor (IPMSM) based on fuzzy-approximation. Fuzzy logic systems are used to approximate the nonlinearities of the discrete-time IPMSM drive system which is derived by direct discretization using Euler method, and a discrete-time fuzzy position tracking controller is designed via backstepping approach. In contrast to existing results, the advantage of the scheme is that the number of the adjustable parameters is reduced to two only and the problem of coupling nonlinearity can be overcome. It is shown that the proposed discrete-time fuzzy controller can guarantee the tracking error converges to a small neighborhood of the origin and all the signals are bounded. Simulation results illustrate the effectiveness and the potentials of the theoretic results obtained.

  7. A current controlled matrix converter for wind energy conversion systems based on permanent magnet synchronous generator

    Directory of Open Access Journals (Sweden)

    Naggar H. Saad

    2016-05-01

    Full Text Available The main challenges of wind energy conversion systems (WECS are to maximize the energy capture from the wind and injecting reactive power during the fault. This paper presents a current controlled matrix converter to interface Permanent Magnet Synchronous Generators (PMSG based WECS with the grid. To achieve fast dynamic response with reduced current ripples, a hysteresis current control is utilized. The proposed control system decouples the active and reactive components of the PMSG current to extract the maximum power from the wind at a given wind velocity and to inject reactive power to the grid. Reactive power injection during the fault satisfying the grid-codes requirement. The proposed WECS has been modeled and simulated using PSCAD/EMTDC software package.

  8. Robust Sliding Mode Control of Permanent Magnet Synchronous Generator-Based Wind Energy Conversion Systems

    Directory of Open Access Journals (Sweden)

    Guangping Zhuo

    2016-12-01

    Full Text Available The subject of this paper pertains to sliding mode control and its application in nonlinear electrical power systems as seen in wind energy conversion systems. Due to the robustness in dealing with unmodeled system dynamics, sliding mode control has been widely used in electrical power system applications. This paper presents first and high order sliding mode control schemes for permanent magnet synchronous generator-based wind energy conversion systems. The application of these methods for control using dynamic models of the d-axis and q-axis currents, as well as those of the high speed shaft rotational speed show a high level of efficiency in power extraction from a varying wind resource. Computer simulation results have shown the efficacy of the proposed sliding mode control approaches.

  9. A low-cost viscometer based on a permanent magnet dc motor

    International Nuclear Information System (INIS)

    Rabani, Amir; Challis, Richard

    2013-01-01

    This paper proposes a pragmatic approach to, and a feasibility study of, a very low cost instrument for on-line and in situ viscosity measurement for engineering applications. It is a simple rotational instrument based on the mixer technique. It utilizes a permanent magnet dc (PMDC) motor which drives a propeller immersed in the test fluid. The viscosity is derived from the motor current when the motor is connected to a fixed supply voltage. The theory which relates PMDC motor current to the resistance to the rotational movement of a body due to the viscosity of the liquid under the test is developed. It is believed that the system provides the basis for a new generation of inexpensive viscometers for process and storage environments. (paper)

  10. A nonlinear controller design for permanent magnet motors using a synchronization-based technique inspired from the Lorenz system.

    Science.gov (United States)

    Zaher, Ashraf A

    2008-03-01

    The dynamic behavior of a permanent magnet synchronous machine (PMSM) is analyzed. Nominal and special operating conditions are explored to show that the PMSM can experience chaos. A nonlinear controller is introduced to control these unwanted chaotic oscillations and to bring the PMSM to a stable steady state. The designed controller uses a pole-placement approach to force the closed-loop system to follow the performance of a simple first-order linear system with zero steady-state error to a desired set point. The similarity between the mathematical model of the PMSM and the famous chaotic Lorenz system is utilized to design a synchronization-based state observer using only the angular speed for feedback. Simulation results verify the effectiveness of the proposed controller in eliminating the chaotic oscillations while using a single feedback signal. The superiority of the proposed controller is further demonstrated by comparing it with a conventional PID controller. Finally, a laboratory-based experiment was conducted using the MCK2812 C Pro-MS(BL) motion control kit to confirm the theoretical results and to verify both the causality and versatility of the proposed controller.

  11. Sensorless control for permanent magnet synchronous motor using a neural network based adaptive estimator

    Science.gov (United States)

    Kwon, Chung-Jin; Kim, Sung-Joong; Han, Woo-Young; Min, Won-Kyoung

    2005-12-01

    The rotor position and speed estimation of permanent-magnet synchronous motor(PMSM) was dealt with. By measuring the phase voltages and currents of the PMSM drive, two diagonally recurrent neural network(DRNN) based observers, a neural current observer and a neural velocity observer were developed. DRNN which has self-feedback of the hidden neurons ensures that the outputs of DRNN contain the whole past information of the system even if the inputs of DRNN are only the present states and inputs of the system. Thus the structure of DRNN may be simpler than that of feedforward and fully recurrent neural networks. If the backpropagation method was used for the training of the DRNN the problem of slow convergence arise. In order to reduce this problem, recursive prediction error(RPE) based learning method for the DRNN was presented. The simulation results show that the proposed approach gives a good estimation of rotor speed and position, and RPE based training has requires a shorter computation time compared to backpropagation based training.

  12. A population-based study of rectal cancer: permanent colostomy as an outcome

    International Nuclear Information System (INIS)

    Paszat, Lawrence F.; Brundage, Michael D.; Groome, Patti A.; Schulze, Karleen; Mackillop, William J.

    1999-01-01

    Purpose: The objectives of this study are to describe the utilization of surgery and of radiotherapy in the treatment of newly diagnosed rectal cancer in Ontario between 1982 and 1994, and to describe the probability of permanent colostomy at any time after the diagnosis of rectal cancer, as an outcome of the treatment of newly diagnosed rectal cancer. Methods and Materials: Electronic records of rectal cancer (International Classification of Diseases code 154) from the Ontario Cancer Registry (n = 18,695, excluding squamous, basaloid, cloacogenic, and carcinoid histology) were linked to surgical records from all Ontario hospitals, and radiotherapy (RT) records from Ontario cancer centers. Procedures occurring within 4 months of diagnosis, or within 4 months of another procedure for rectal cancer, were considered part of initial treatment. Multivariate analyses controlled for age, sex, and year of diagnosis. Results: Resection plus permanent colostomy was performed in 33.1% of cases, whereas local excision or resection without permanent colostomy was performed in 38.2%. Multivariate logistic regression demonstrated higher odds ratios (OR) for resection plus permanent colostomy in all regions of Ontario relative to Toronto. The OR for postoperative RT following local excision or resection without permanent colostomy varied among the regions relative to Toronto (e.g., OR Ottawa = 0.59, OR Hamilton 0.76, OR London = 1.25). The relative risk (RR) of colostomy conditional upon survival within 5 years from diagnosis varied among regions relative to Toronto (e.g., RR Ottawa = 1.21, RR Hamilton = 1.20). Conclusions: There is regional variation in the utilization of resection with permanent colostomy, and in the utilization of postoperative RT among cases not undergoing permanent colostomy. Regions with higher initial rates of resection plus permanent colostomy continue to experience higher probability of permanent colostomy 5 years after diagnosis of rectal cancer. Higher

  13. Adaptive PIF Control for Permanent Magnet Synchronous Motors Based on GPC

    Directory of Open Access Journals (Sweden)

    Shaowu Lu

    2012-12-01

    Full Text Available To enhance the control performance of permanent magnet synchronous motors (PMSMs, a generalized predictive control (GPC-based proportional integral feedforward (PIF controller is proposed for the speed control system. In this new approach, firstly, based on the online identification of controlled model parameters, a simplified GPC law supplies the PIF controller with suitable control parameters according to the uncertainties in the operating conditions. Secondly, the speed reference curve for PMSMs is usually required to be continuous and continuously differentiable according to the general servo system design requirements, so the adaptation of the speed reference is discussed in details in this paper. Hence, the performance of the speed control system using a GPC-based PIF controller is improved for tracking some specified signals. The main motivation of this paper is the extension of GPC law to replace the traditional PI or PIF controllers in industrial applications. The efficacy and usefulness of the proposed controller are verified through experimental results.

  14. Behavior based safety

    International Nuclear Information System (INIS)

    Sudhikumaran, T.V.; Mehta, S.C.; Goyal, D.K.

    2009-01-01

    Behaviour Based Safety (popularly known as BBS) is a new methodology for achieving injury free work place and total Safety Culture. BBS is successfully being implemented and is being practiced as a work methodology for achieving a loss and injury free work environment and work practice. Through BBS, it was brought out that the root causes of all Industrial accidents some how originate from the 'at risk' behaviour of some individual or group of individuals at some level. The policy of NPCIL is to excel in the field of Industrial and Fire Safety in comparison to international standards. This article indents to bring out the various parameters helping in installing BBS programme at any plant. (author)

  15. Stable adaptive PI control for permanent magnet synchronous motor drive based on improved JITL technique.

    Science.gov (United States)

    Zheng, Shiqi; Tang, Xiaoqi; Song, Bao; Lu, Shaowu; Ye, Bosheng

    2013-07-01

    In this paper, a stable adaptive PI control strategy based on the improved just-in-time learning (IJITL) technique is proposed for permanent magnet synchronous motor (PMSM) drive. Firstly, the traditional JITL technique is improved. The new IJITL technique has less computational burden and is more suitable for online identification of the PMSM drive system which is highly real-time compared to traditional JITL. In this way, the PMSM drive system is identified by IJITL technique, which provides information to an adaptive PI controller. Secondly, the adaptive PI controller is designed in discrete time domain which is composed of a PI controller and a supervisory controller. The PI controller is capable of automatically online tuning the control gains based on the gradient descent method and the supervisory controller is developed to eliminate the effect of the approximation error introduced by the PI controller upon the system stability in the Lyapunov sense. Finally, experimental results on the PMSM drive system show accurate identification and favorable tracking performance. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

  16. Biosphere 2: a prototype project for a permanent and evolving life system for Mars base.

    Science.gov (United States)

    Nelson, M; Allen, J P; Dempster, W F

    1992-01-01

    As part of the ground-based preparation for creating long-term life systems needed for space habitation and settlement, Space Biospheres Ventures (SBV) is undertaking the Biosphere 2 project near Oracle, Arizona. Biosphere 2, currently under construction, is scheduled to commence its operations in 1991 with a two-year closure period with a crew of eight people. Biosphere 2 is a facility which will be essentialy materially-closed to exchange with the outside environment. It is open to information and energy flow. Biosphere 2 is designed to achieve a complex life-support system by the integration of seven areas or "biomes"--rainforest, savannah, desert, marsh, ocean, intensive agriculture and human habitat. Unique bioregenerative technologies, such as soil bed reactors for air purification, aquatic waste processing systems, real-time analytic systems and complex computer monitoring and control systems are being developed for the Biosphere 2 project. Its operation should afford valuable insight into the functioning of complex life systems necessary for long-term habitation in space. It will serve as an experimental ground-based prototype and testbed for the stable, permanent life systems needed for human exploration of Mars.

  17. Biosphere 2: A prototype project for a permanent and evolving life system for Mars base

    Science.gov (United States)

    Nelson, Mark; Allen, John P.; Dempster, William F.

    As part of the ground-based preparation for creating long-term life systems needed for space habitation and settlement, Space Biopsheres Ventures (SBV) is undertaking the Biosphere 2 project near Oracle, Arizona. Biosphere 2, currently under construction, is scheduled to commence its operations in 1991 with a two-year closure period with a crew of eight people. Biosphere 2 is a facility which will be essentially materially-closed to exchange with the outside environment. It is open to information and energy flow. Biosphere 2 is designed to achieve a complex life-support system by the integration of seven areas or ``biomes'' - rainforest, savannah, desert, marsh, ocean, intensive agriculture and human habitat. Unique bioregenerative technologies, such as soil bed reactors for air purification, aquatic waste processing systems, real-time analytic systems and complex computer monitoring and control systems are being developed for the Biosphere 2 project. Its operation should afford valuable insight into the functioning of complex life systems necessary for long-term habitation in space. It will serve as an experimental ground-based prototype and testbed for the stable, permanent life systems needed for human exploration of Mars.

  18. Phase-Inductance-Based Position Estimation Method for Interior Permanent Magnet Synchronous Motors

    Directory of Open Access Journals (Sweden)

    Xin Qiu

    2017-12-01

    Full Text Available This paper presents a phase-inductance-based position estimation method for interior permanent magnet synchronous motors (IPMSMs. According to the characteristics of phase induction of IPMSMs, the corresponding relationship of the rotor position and the phase inductance is obtained. In order to eliminate the effect of the zero-sequence component of phase inductance and reduce the rotor position estimation error, the phase inductance difference is employed. With the iterative computation of inductance vectors, the position plane is further subdivided, and the rotor position is extracted by comparing the amplitudes of inductance vectors. To decrease the consumption of computer resources and increase the practicability, a simplified implementation is also investigated. In this method, the rotor position information is achieved easily, with several basic math operations and logical comparisons of phase inductances, without any coordinate transformation or trigonometric function calculation. Based on this position estimation method, the field orientated control (FOC strategy is established, and the detailed implementation is also provided. A series of experiment results from a prototype demonstrate the correctness and feasibility of the proposed method.

  19. Permanent health education based on research with professionals of a multidisciplinary residency program: case study

    Directory of Open Access Journals (Sweden)

    Cristiane Trivisiol da Silva

    Full Text Available This research aims to identify the perception of professional members of a multi-professional residency program on Permanent Health Education. It is a case study research using a qualitative approach, with sixteen members of a multi-professional residency program. The data were collected from January to May 2012, through semi-structured interviews, document analysis and systematic observation, and analyzed according to Thematic Content Analysis. Two categories were identified: Permanent Health Education establishing collective spaces of reflection of practices and Permanent Health Education that promotes integration between disciplines. The members of the multiprofessional residency team were found to be aware that permanent education permeates their training and enables reflection on their clinical practices and multidisciplinary action as producers of health actions.

  20. The research and development of inclination angle magnetic fluid detector with a movable sensing element based on permanent magnets

    Energy Technology Data Exchange (ETDEWEB)

    Lagutkina, D.Yu., E-mail: Lagutkina_D@mail.ru; Saikin, M.S., E-mail: saikinms@mail.ru

    2017-06-01

    The article presents an account on some new designs, which have been developed for the magnetic fluid sensor with a movable sensor based on permanent magnets with the support of Ivanovo State Power Engineering University. The research carried out is aimed at elucidating the influence of the detector sensing element on its operating performance. - Highlights: • In order to conduct a careful research of IAMFD designs operating performance the algorithm was applied to look into the SE suspension force dependencies on its spatial position. • According to this algorithm, the value of the sensitive element suspension force is obtained with use of the MF attraction force of the to the permanent magnet.

  1. Effect of Environmental Education Based on Transformational Learning Theory on Perceptions towards Environmental Problems and Permanency of Learning

    Science.gov (United States)

    Uyanik, Gökhan

    2016-01-01

    The aim of the study is to determine effect of environmental education based on transformational learning theory on primary school teacher candidates' perceptions towards environmental problems and permanency of learning. Pretest-posttest quasi-experimental design have been used in this study. The study group consists of 66 teacher candidates who…

  2. System frequency support of permanent magnet synchronous generator-based wind power plant

    Science.gov (United States)

    Wu, Ziping

    With ever-increasing penetration of wind power into modern electric grids all over the world, a trending replacement of conventional synchronous generators by large wind power plants will likely result in the poor overall frequency regulation performance. On the other hand, permanent magnet synchronous generator wind Turbine System (PMSG-WTG) with full power back to back converters tends to become one of the most promising wind turbine technologies thanks to various advantages. It possesses a significant amount of kinetic energy stored in the rotating mass of turbine blades, which can be utilized to enhance the total inertia of power system. Additionally, the deloaded operation and decoupled control of active and reactive power make it possible for PMSG-WTG to provide a fast frequency regulation through full-power converter. First of all, a comprehensive and in-depth survey is conducted to analyze the motivations for incorporating the inertial response and frequency regulation of VSWT into the system frequency regulation. Besides, control classifications, fundamental control concepts and advanced control schemes implemented for auxiliary frequency support of individual WT or wind power plant are elaborated along with a comparison of the potential frequency regulation capabilities of four major types of WTs. Secondly, a Controls Advanced Research Turbine2-Permanent Magnet Synchronous Generator wind turbine (CART2-PMSG) integrated model representing the typical configuration and operation characteristics of PMSG-WT is established in Matlab/Simulink,. Meanwhile, two different rotor-side converter control schemes, including rotor speed-based control and active power-based control, are integrated into this CART2-PMSG integrated model to perform Maximum Power Point Tracking (MPPT) operation over a wide range of wind speeds, respectively. Thirdly, a novel comprehensive frequency regulation (CFR) control scheme is developed and implemented into the CART2-PMSG model based

  3. Performance evaluation of a permanent ring magnet based helicon plasma source for negative ion source research

    Science.gov (United States)

    Pandey, Arun; Bandyopadhyay, M.; Sudhir, Dass; Chakraborty, A.

    2017-10-01

    Helicon wave heated plasmas are much more efficient in terms of ionization per unit power consumed. A permanent magnet based compact helicon wave heated plasma source is developed in the Institute for Plasma Research, after carefully optimizing the geometry, the frequency of the RF power, and the magnetic field conditions. The HELicon Experiment for Negative ion-I source is the single driver helicon plasma source that is being studied for the development of a large sized, multi-driver negative hydrogen ion source. In this paper, the details about the single driver machine and the results from the characterization of the device are presented. A parametric study at different pressures and magnetic field values using a 13.56 MHz RF source has been carried out in argon plasma, as an initial step towards source characterization. A theoretical model is also presented for the particle and power balance in the plasma. The ambipolar diffusion process taking place in a magnetized helicon plasma is also discussed.

  4. On Position Sensorless Control for Permanent Magnet Synchronous Motor Based on a New Sliding Mode Observer

    Directory of Open Access Journals (Sweden)

    Qixin Zhu

    2014-10-01

    Full Text Available For the problems of buffeting and phase delay in traditional rotor detection in sensorless vector control of permanent magnet synchronous motor (PMSM, the Sigmoid function is proposed to replace sign function and the approach of piecewise linearization is proposed to compensate phase delay. To the problem that the output of traditional low pass filter contains high- order harmonic, two-stage filter including traditional low-pass filter and Kalman filter is proposed in this paper. Based on the output of traditional first-order low-pass filter, the Kalman filter is used to get modified back-EMF. The phase-locked loop control of rotor position is adopted to estimate motor position and speed. A Matlab/Simulink simulation model of PMSM position servo control system is established. The simulation analysis of the new sliding mode observer’s back-EMF detection, position and speed estimation, load disturbance and dynamic process are carried out respectively. Simulation results verify feasibility of the new sliding mode observer algorithm.

  5. Risk behavior and access to HIV/AIDS prevention services in a community sample of homeless persons entering permanent supportive housing.

    Science.gov (United States)

    Wenzel, Suzanne L; Rhoades, Harmony; Harris, Taylor; Winetrobe, Hailey; Rice, Eric; Henwood, Ben

    2017-05-01

    Homeless persons suffer disproportionately high rates of HIV infection, and moving into permanent supportive housing (PSH) can provide a stable base from which to access needed prevention services. However, little is known about HIV risk or prevention behavior during this critical time of transition. The current study investigated STI and HIV risk and prevention behavior and recent use of prevention and treatment services (i.e., education, testing, medication) among homeless persons preparing to move into PSH. Data come from interviews with 421 homeless adults before they moved into PSH. Thirty-seven percent of the respondents were sexually active; of those, 75.7% reported unprotected sex. Nearly two-thirds (64%) reported past year HIV testing and 40% reported testing for another STI. Fewer than one-third (31%) of respondents reported receiving posttest counseling at their last HIV test. HIV seropositivity was self-reported by 10%. Among those persons who were HIV-positive, 57.1% reported less than 100% antiretroviral (ARV) adherence. Among HIV-negative respondents, less than 1% had been prescribed preexposure prophylaxis (PrEP). Less than half (46.4%) of the sample reported any HIV prevention education in the past year. This population of homeless adults about to move into PSH report high rates of HIV risk behavior, but low rates of HIV prevention education and very little PrEP utilization. Further, low rates of ARV adherence among HIV-positive respondents indicate significant risk for HIV transmission and acquisition. Entering PSH is a period of transition for homeless persons when integrated care is critically important to ensure positive health outcomes, but these data suggest that PrEP and other HIV prevention services are poorly accessed among this population. As such, multipronged services that integrate PrEP and other HIV prevention services are needed to prevent transmission and acquisition of HIV in this high-risk, vulnerable population and ensure the

  6. PCR-based identification of selected pathogens associated with endodontic infections in deciduous and permanent teeth.

    Science.gov (United States)

    Cogulu, Dilsah; Uzel, Atac; Oncag, Ozant; Eronat, Cemal

    2008-09-01

    The aim of the present study was to evaluate the presence of the selected pathogens in samples from deciduous and permanent tooth root canals by using PCR method and to determine the association of these organisms with clinical symptoms. A total of 145 children, 5 to 13 years old, were involved in this study. The presence of selected pathogens (Actinomyces israelii, Candida albicans, Enterococcus faecalis, Fusobacterium nucleatum, Porphyromonas endodontalis, Porphyromonas gingivalis, Prevotella intermedia, Streptococcus intermedius, Treponema denticola, Parvimonas micra, Tannerella forsythensis, Enterococcus faecium, Prevotella melaninogenica) in infected root canals was studied using PCR. T. denticola (P = .012, .02) and E. faecalis (P = .012, .04) were highly associated with periapical radiolucency and previous pain, while P. gingivalis was associated with tenderness to percussion in both deciduous and permanent teeth (P = .01, .015). The results of the present study confirm that certain species of microorganisms are associated with clinical signs and symptoms of endodontic disease in both deciduous and permanent teeth.

  7. Comparison of stator-mounted permanent-magnet machines based on a general power equation

    DEFF Research Database (Denmark)

    Chen, Zhe; Hua, Wei; Cheng, Ming

    2009-01-01

    The stator-mounted permanent-magnet (SMPM) machines have some advantages compared with its counterparts, such as simple rotor, short winding terminals, and good thermal dissipation conditions for magnets. In this paper, a general power equation for three types of SMPM machine is introduced first...

  8. Permanence and asymptotic behaviors of stochastic predator-prey system with Markovian switching and Lévy noise

    Science.gov (United States)

    Wang, Sheng; Wang, Linshan; Wei, Tengda

    2018-04-01

    This paper concerns the dynamics of a stochastic predator-prey system with Markovian switching and Lévy noise. First, the existence and uniqueness of global positive solution to the system is proved. Then, by combining stochastic analytical techniques with M-matrix analysis, sufficient conditions of stochastic permanence and extinction are obtained. Furthermore, for the stochastic permanence case, by means of four constants related to the stationary probability distribution of the Markov chain and the parameters of the subsystems, both the superior limit and the inferior limit of the average in time of the sample path of the solution are estimated. Finally, our conclusions are illustrated through an example.

  9. Behavior-based evacuation planning

    KAUST Repository

    Rodriguez, Samuel

    2010-05-01

    In this work, we present a formulation of an evacuation planning problem that is inspired by motion planning and describe an integrated behavioral agent-based and roadmap-based motion planning approach to solve it. Our formulation allows users to test the effect on evacuation of a number of different environmental factors. One of our main focuses is to provide a mechanism to investigate how the interaction between agents influences the resulting evacuation plans. Specifically, we explore how various types of control provided by a set of directing agents effects the overall evacuation planning strategies of the evacuating agents. ©2010 IEEE.

  10. Behavior-based evacuation planning

    KAUST Repository

    Rodriguez, Samuel; Amato, Nancy M

    2010-01-01

    In this work, we present a formulation of an evacuation planning problem that is inspired by motion planning and describe an integrated behavioral agent-based and roadmap-based motion planning approach to solve it. Our formulation allows users to test the effect on evacuation of a number of different environmental factors. One of our main focuses is to provide a mechanism to investigate how the interaction between agents influences the resulting evacuation plans. Specifically, we explore how various types of control provided by a set of directing agents effects the overall evacuation planning strategies of the evacuating agents. ©2010 IEEE.

  11. Diagnosis of Short-Circuit Fault in Large-Scale Permanent-Magnet Wind Power Generator Based on CMAC

    Directory of Open Access Journals (Sweden)

    Chin-Tsung Hsieh

    2013-01-01

    Full Text Available This study proposes a method based on the cerebellar model arithmetic controller (CMAC for fault diagnosis of large-scale permanent-magnet wind power generators and compares the results with Error Back Propagation (EBP. The diagnosis is based on the short-circuit faults in permanent-magnet wind power generators, magnetic field change, and temperature change. Since CMAC is characterized by inductive ability, associative ability, quick response, and similar input signals exciting similar memories, it has an excellent effect as an intelligent fault diagnosis implement. The experimental results suggest that faults can be diagnosed effectively after only training CMAC 10 times. In comparison to training 151 times for EBP, CMAC is better than EBP in terms of training speed.

  12. Research on Strategies and Methods Suppressing Permanent Magnet Demagnetization in Permanent Magnet Synchronous Motors Based on a Multi-Physical Field and Rotor Multi-Topology Structure

    Directory of Open Access Journals (Sweden)

    Lin Li

    2017-12-01

    Full Text Available In this paper, a permanent magnet synchronous motor (PMSM with sleeves on the rotor outer surface is investigated. The purpose of sleeves is to fix the permanent magnets and protect them from being destroyed by the large centrifugal force. However, the sleeve material characteristics have a great influence on the PMSM, and therewith, most of the rotor eddy-current losses are generated in the rotor sleeve, which could increase the device temperature and even cause thermal demagnetization of the magnets. Thus, a sleeve scheme design with low eddy-current losses is necessary, and a method suppressing the local temperature peak of permanent magnets is presented. The 3-D electromagnetic finite element model of a 12.5 kW, 2000 r/min PMSM with a segmented sleeve is established, and the electromagnetic field is calculated by using the finite element method. The results show the effectiveness of the presented method in reducing the eddy current losses in the rotor. Using the thermal method, it can be found that the maximum temperature position and zone of permanent magnet will change. Thus, some strategies are comparatively analyzed in order to obtain the change rule of the position and zone. The obtained conclusions may provide a useful reference for the design and research of PMSMs.

  13. Research on magnetorheological damper suspension with permanent magnet and magnetic valve based on developed FOA-optimal control algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Ping; Gao, Hong [Anhui Polytechnic University, Wuhu (China); Niu, Limin [Anhui University of Technology, Maanshan (China)

    2017-07-15

    Due to the fail safe problem, it was difficult for the existing Magnetorheological damper (MD) to be widely applied in automotive suspensions. Therefore, permanent magnets and magnetic valves were introduced to existing MDs so that fail safe problem could be solved by the magnets and damping force could be adjusted easily by the magnetic valve. Thus, a new Magnetorheological damper with permanent magnet and magnetic valve (MDPMMV) was developed and MDPMMV suspension was studied. First of all, mechanical structure of existing magnetorheological damper applied in automobile suspensions was redesigned, comprising a permanent magnet and a magnetic valve. In addition, prediction model of damping force was built based on electromagnetics theory and Bingham model. Experimental research was onducted on the newly designed damper and goodness of fit between experiment results and simulated ones by models was high. On this basis, a quarter suspension model was built. Then, fruit Fly optimization algorithm (FOA)-optimal control algorithm suitable for automobile suspension was designed based on developing normal FOA. Finally, simulation experiments and bench tests with input surface of pulse road and B road were carried out and the results indicated that working erformance of MDPMMV suspension based on FOA-optimal control algorithm was good.

  14. Modeling and simulation of permanent magnet synchronous motor based on neural network control strategy

    Science.gov (United States)

    Luo, Bingyang; Chi, Shangjie; Fang, Man; Li, Mengchao

    2017-03-01

    Permanent magnet synchronous motor is used widely in industry, the performance requirements wouldn't be met by adopting traditional PID control in some of the occasions with high requirements. In this paper, a hybrid control strategy - nonlinear neural network PID and traditional PID parallel control are adopted. The high stability and reliability of traditional PID was combined with the strong adaptive ability and robustness of neural network. The permanent magnet synchronous motor will get better control performance when switch different working modes according to different controlled object conditions. As the results showed, the speed response adopting the composite control strategy in this paper was faster than the single control strategy. And in the case of sudden disturbance, the recovery time adopting the composite control strategy designed in this paper was shorter, the recovery ability and the robustness were stronger.

  15. Hot-tearing of multicomponent Al-Cu alloys based on casting load measurements in a constrained permanent mold

    Energy Technology Data Exchange (ETDEWEB)

    Sabau, Adrian S [ORNL; Mirmiran, Seyed [Fiat Chrysler Automobiles North America; Glaspie, Christopher [Fiat Chrysler Automobiles North America; Li, Shimin [Worcester Polytechnic Institute (WPI), MA; Apelian, Diran [Worcester Polytechnic Institute (WPI), MA; Shyam, Amit [ORNL; Haynes, James A [ORNL; Rodriguez, Andres [Nemak, Garza Garcia, N.L., Mexico

    2017-01-01

    Hot-tearing is a major casting defect that is often difficult to characterize, especially for multicomponent Al alloys used for cylinder head castings. The susceptibility of multicomponent Al-Cu alloys to hot-tearing during permanent mold casting was investigated using a constrained permanent mold in which the load and displacement was measured. The experimental results for hot tearing susceptibility are compared with those obtained from a hot-tearing criterion based temperature range evaluated at fraction solids of 0.87 and 0.94. The Cu composition was varied from approximately 5 to 8 pct. (weight). Casting experiments were conducted without grain refining. The measured load during casting can be used to indicate the severity of hot tearing. However, when small hot-tears are present, the load variation cannot be used to detect and assess hot-tearing susceptibility.

  16. Predictive control strategies for wind turbine system based on permanent magnet synchronous generator.

    Science.gov (United States)

    Maaoui-Ben Hassine, Ikram; Naouar, Mohamed Wissem; Mrabet-Bellaaj, Najiba

    2016-05-01

    In this paper, Model Predictive Control and Dead-beat predictive control strategies are proposed for the control of a PMSG based wind energy system. The proposed MPC considers the model of the converter-based system to forecast the possible future behavior of the controlled variables. It allows selecting the voltage vector to be applied that leads to a minimum error by minimizing a predefined cost function. The main features of the MPC are low current THD and robustness against parameters variations. The Dead-beat predictive control is based on the system model to compute the optimum voltage vector that ensures zero-steady state error. The optimum voltage vector is then applied through Space Vector Modulation (SVM) technique. The main advantages of the Dead-beat predictive control are low current THD and constant switching frequency. The proposed control techniques are presented and detailed for the control of back-to-back converter in a wind turbine system based on PMSG. Simulation results (under Matlab-Simulink software environment tool) and experimental results (under developed prototyping platform) are presented in order to show the performances of the considered control strategies. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

  17. Permanent education

    International Nuclear Information System (INIS)

    Gardien, S.; Kirsch, R.

    1998-01-01

    The permanent education of the IPN-Lyon inscribes itself completely in the priorities of the tri-annual plan of education of CNRS. These priorities contribute to evolution of research, evaluation of the professions, integration during the professional carriers of the personnel and form the frame for new management practice implementation

  18. Comparison Study of Electromagnet and Permanent Magnet Systems for an Accelerator Using Cost-Based Failure Modes and Effects Analysis

    International Nuclear Information System (INIS)

    Spencer, C

    2004-01-01

    The next generation of particle accelerators will be one-of-a-kind facilities, and to meet their luminosity goals they must have guaranteed availability over their several decade lifetimes. The Next Linear Collider (NLC) is one viable option for a 1 TeV electron-positron linear collider, it has an 85% overall availability goal. We previously showed how a traditional Failure Modes and Effects Analysis (FMEA) of a SLAC electromagnet leads to reliability-enhancing design changes. Traditional FMEA identifies failure modes with high risk but does not consider the consequences in terms of cost, which could lead to unnecessarily expensive components. We have used a new methodology, ''Life Cost-Based FMEA'', which measures risk of failure in terms of cost, in order to evaluate and compare two different technologies that might be used for the 8653 NLC magnets: electromagnets or permanent magnets. The availabilities for the two different types of magnet systems have been estimated using empirical data from SLAC's accelerator failure database plus expert opinion on permanent magnet failure modes and industry standard failure data. Labor and material costs to repair magnet failures are predicted using a Monte Carlo simulation of all possible magnet failures over a 30-year lifetime. Our goal is to maximize up-time of the NLC through magnet design improvements and the optimal combination of electromagnets and permanent magnets, while reducing magnet system lifecycle costs

  19. Direct current force sensing device based on compressive spring, permanent magnet, and coil-wound magnetostrictive/piezoelectric laminate.

    Science.gov (United States)

    Leung, Chung Ming; Or, Siu Wing; Ho, S L

    2013-12-01

    A force sensing device capable of sensing dc (or static) compressive forces is developed based on a NAS106N stainless steel compressive spring, a sintered NdFeB permanent magnet, and a coil-wound Tb(0.3)Dy(0.7)Fe(1.92)/Pb(Zr, Ti)O3 magnetostrictive∕piezoelectric laminate. The dc compressive force sensing in the device is evaluated theoretically and experimentally and is found to originate from a unique force-induced, position-dependent, current-driven dc magnetoelectric effect. The sensitivity of the device can be increased by increasing the spring constant of the compressive spring, the size of the permanent magnet, and/or the driving current for the coil-wound laminate. Devices of low-force (20 N) and high-force (200 N) types, showing high output voltages of 262 and 128 mV peak, respectively, are demonstrated at a low driving current of 100 mA peak by using different combinations of compressive spring and permanent magnet.

  20. Initial position estimation method for permanent magnet synchronous motor based on improved pulse voltage injection

    DEFF Research Database (Denmark)

    Wang, Z.; Lu, K.; Ye, Y.

    2011-01-01

    According to saliency of permanent magnet synchronous motor (PMSM), the information of rotor position is implied in performance of stator inductances due to the magnetic saturation effect. Researches focused on the initial rotor position estimation of PMSM by injecting modulated pulse voltage...... vectors. The relationship between the inductance variations and voltage vector positions was studied. The inductance variation effect on estimation accuracy was studied as well. An improved five-pulses injection method was proposed, to improve the estimation accuracy by choosing optimaized voltage vectors...

  1. Deformation of the Japanese Islands and seismic coupling: an interpretation based on GSI permanent GPS observations

    Science.gov (United States)

    Le Pichon, Xavier; Mazzotti, Stéphane; Henry, Pierre; Hashimoto, Manabu

    1998-08-01

    The entire area of the Japanese Islands has been covered by the permanent GPS observation network of the Geographical Survey Institute since 1994. In this paper we use a solution for the vectors of motion during 1995 for a selection of 116 stations to discuss the origin of the observed deformation field. We refer the displacement field to Eurasia using the VLBI-determined motion of Kashima and demonstrate that other choices such as the Okhotsk or North American plates for north Japan are not compatible with the data. 1 yr GPS velocities are much higher than geological constraints would allow because these short-term measurements include transient elastic deformation. However, the good qualitative agreement between the observed geodetic deformation tensors and those inferred from active faults and earthquakes suggests that the Quaternary permanent deformation is essentially the result of the transfer of part of the subduction-induced elastic deformation into permanent plastic deformation. We then compute the elastic deformation of the Japanese Islands caused by interseismic loading of the Pacific and Philippine subduction planes. The geometry of the coupled zone and its downward extension are determined from the distribution of earthquakes for the Pacific slab. For the Philippine slab we use the geometry proposed by Hyndman et al. (1995). These elastic models account for most of the observed velocity field if the subduction movement of the Philippine Sea Plate is 100 per cent locked and if that of the Pacific Plate is 75-85 per cent locked. We note that the boundaries of the areas where significant elastic deformation is predicted (more than 10 mm yr-1 of motion with respect to Eurasia) coincide with the main zones of permanent deformation: the Eastern Japan Sea deformation zone for the Pacific subduction elastic deformation field and the Setouchi/MTL deformation zone for the Nankai field. Each zone probably accommodates 10-15 mm yr-1 of motion in the long term

  2. Power Control of Permanent Magnet Generator Based Variable Speed Wind Turbines

    DEFF Research Database (Denmark)

    Deng, Fujin; Chen, Zhe

    2009-01-01

    When the wind power accounts for a large portion of the grid, it will be required to regulate the active power and reactive power. This paper investigates a MWlevel variable speed wind turbine with a permanent magnet synchronous generator (PMSG). The power control capabilities of two kinds...... of control schemes conducted respectively on this wind turbine under two conditions, including rapid wind speed change and grids faults, are compared. The simulation study of the wind turbine system is conducted using PSCAD/EMTDC, and the results show the different power control capabilities of the two...

  3. Permanent quadrupole magnets

    International Nuclear Information System (INIS)

    Bush, E.D. Jr.

    1976-01-01

    A family of quadrupole magnets using a soft iron return yoke and circular cross-section permanent magnet poles were fabricated to investigate the feasibility for use in ion or electron beam focusing applications in accelerators and transport lines. Magnetic field measurements yielded promising results. In fixed-field applications, permanent magnets with sufficient gradients would be a low cost substitute for conventional electromagnets, eliminating the need for power supplies, associated wiring, and cooling. Based on preliminary tests, it was seen that permanent quadrupole magnets can offer a low cost, reliable solution in applications requiring small, fixed-field focusing devices for use in ion or electron-beam transport systems. Permanent magnets do require special considerations in design, fabrication, handling, and service that are different than encountered in conventional quadrupole magnets. If these basic conditions are satisfied, the resulting beam-focusing device would be stable, maintenance free, with virtually an indefinite lifetime

  4. Anomalous magneto-structural behavior of MnBi explained: A path towards an improved permanent magnet

    Energy Technology Data Exchange (ETDEWEB)

    Zarkevich, N. A., E-mail: zarkev@ameslab.gov; Wang, L.-L. [The Ames Laboratory, U.S. Department of Energy, Ames, Iowa 50011 (United States); Johnson, D. D. [The Ames Laboratory, U.S. Department of Energy, Ames, Iowa 50011 (United States); Materials Science and Engineering, Iowa State University, Ames, Iowa 50011 (United States)

    2014-03-01

    Low-temperature MnBi (hexagonal NiAs phase) exhibits anomalies in the lattice constants (a, c) and bulk elastic modulus (B) below 100 K, spin reorientation and magnetic susceptibility maximum near 90 K, and, importantly for high-temperature magnetic applications, an increasing coercivity (unique to MnBi) above 180  K. We calculate the total energy and magneto-anisotropy energy (MAE) versus (a, c) using DFT+U methods. We reproduce and explain all the above anomalies. We predict that coercivity and MAE increase due to increasing a, suggesting means to improve MnBi permanent magnets.

  5. Anomalous magneto-structural behavior of MnBi explained: A path towards an improved permanent magnet

    Energy Technology Data Exchange (ETDEWEB)

    Zarkevich, NA; Wang, LL; Johnson, DD

    2014-03-01

    Low-temperature MnBi (hexagonal NiAs phase) exhibits anomalies in the lattice constants (a, c) and bulk elastic modulus (B) below 100 K, spin reorientation and magnetic susceptibility maximum near 90 K, and, importantly for high-temperature magnetic applications, an increasing coercivity (unique to MnBi) above 180 K. We calculate the total energy and magneto-anisotropy energy (MAE) versus (a, c) using DFT+U methods. We reproduce and explain all the above anomalies. We predict that coercivity and MAE increase due to increasing a, suggesting means to improve MnBi permanent magnets. (C) 2014 Author(s).

  6. Permanent Magnet Synchronous Generator Driven Wind Energy Conversion System Based on Parallel Active Power Filter

    Directory of Open Access Journals (Sweden)

    FERDI Brahim

    2014-05-01

    Full Text Available This paper proposes a novel application of the instantaneous P-Q theory in a wind energy conversion system (WECS. The proposed WECS is formed by permanent magnet synchronous generator (PMSG wind turbine system connected to the grid through parallel active power filter (PAPF. PAPF uses the generated wind energy to feed loads connected at the point of common coupling (PPC, compensates current harmonics and injects the excess of this energy into the grid using P-Q theory as control method. To demonstrate the feasibility and the performance of the proposed control scheme, simulation of this wind system has been realized using MATLAB/SIMULINK software. Simulation results show the accuracy and validity of the proposed control scheme for the PMSGPAPF system.

  7. Design of permanent magnet synchronous motor speed loop controller based on sliding mode control algorithm

    Science.gov (United States)

    Qiang, Jiang; Meng-wei, Liao; Ming-jie, Luo

    2018-03-01

    Abstract.The control performance of Permanent Magnet Synchronous Motor will be affected by the fluctuation or changes of mechanical parameters when PMSM is applied as driving motor in actual electric vehicle,and external disturbance would influence control robustness.To improve control dynamic quality and robustness of PMSM speed control system, a new second order integral sliding mode control algorithm is introduced into PMSM vector control.The simulation results show that, compared with the traditional PID control,the modified control scheme optimized has better control precision and dynamic response ability and perform better with a stronger robustness facing external disturbance,it can effectively solve the traditional sliding mode variable structure control chattering problems as well.

  8. Permanent magnet synchronous motor servo system control based on μC/OS

    Science.gov (United States)

    Shi, Chongyang; Chen, Kele; Chen, Xinglong

    2015-10-01

    When Opto-Electronic Tracking system operates in complex environments, every subsystem must operate efficiently and stably. As a important part of Opto-Electronic Tracking system, the performance of PMSM(Permanent Magnet Synchronous Motor) servo system affects the Opto-Electronic Tracking system's accuracy and speed greatly[1][2]. This paper applied embedded real-time operating system μC/OS to the control of PMSM servo system, implemented SVPWM(Space Vector Pulse Width Modulation) algorithm in PMSM servo system, optimized the stability of PMSM servo system. Pointing on the characteristics of the Opto-Electronic Tracking system, this paper expanded μC/OS with software redundancy processes, remote debugging and upgrading. As a result, the Opto- Electronic Tracking system performs efficiently and stably.

  9. Demographic, socioeconomic, and behavioral factors affecting patterns of tooth decay in the permanent dentition: principal components and factor analyses.

    Science.gov (United States)

    Shaffer, John R; Polk, Deborah E; Feingold, Eleanor; Wang, Xiaojing; Cuenco, Karen T; Weeks, Daniel E; DeSensi, Rebecca S; Weyant, Robert J; Crout, Richard; McNeil, Daniel W; Marazita, Mary L

    2013-08-01

    Dental caries of the permanent dentition is a multifactorial disease resulting from the complex interplay of endogenous and environmental risk factors. The disease is not easily quantitated due to the innumerable possible combinations of carious lesions across individual tooth surfaces of the permanent dentition. Global measures of decay, such as the DMFS index (which was developed for surveillance applications), may not be optimal for studying the epidemiology of dental caries because they ignore the distinct patterns of decay across the dentition. We hypothesize that specific risk factors may manifest their effects on specific tooth surfaces leading to patterns of decay that can be identified and studied. In this study, we utilized two statistical methods of extracting patterns of decay from surface-level caries data to create novel phenotypes with which to study the risk factors affecting dental caries. Intra-oral dental examinations were performed on 1068 participants aged 18-75 years to assess dental caries. The 128 tooth surfaces of the permanent dentition were scored as carious or not and used as input for principal components analysis (PCA) and factor analysis (FA), two methods of identifying underlying patterns without a priori knowledge of the patterns. Demographic (age, sex, birth year, race/ethnicity, and educational attainment), anthropometric (height, body mass index, waist circumference), endogenous (saliva flow), and environmental (tooth brushing frequency, home water source, and home water fluoride) risk factors were tested for association with the caries patterns identified by PCA and FA, as well as DMFS, for comparison. The ten strongest patterns (i.e. those that explain the most variation in the data set) extracted by PCA and FA were considered. The three strongest patterns identified by PCA reflected (i) global extent of decay (i.e. comparable to DMFS index), (ii) pit and fissure surface caries and (iii) smooth surface caries, respectively. The

  10. Evidence-Based Behavioral Interventions for Repetitive Behaviors in Autism

    Science.gov (United States)

    Boyd, Brian A.; McDonough, Stephen G.; Bodfish, James W.

    2012-01-01

    Restricted and repetitive behaviors (RRBs) are a core symptom of autism spectrum disorders (ASD). There has been an increased research emphasis on repetitive behaviors; however, this research primarily has focused on phenomenology and mechanisms. Thus, the knowledge base on interventions is lagging behind other areas of research. The literature…

  11. Timing of computed tomography-based postimplant assessment following permanent transperineal prostate brachytherapy

    International Nuclear Information System (INIS)

    Prestidge, Bradley R.; Bice, William S.; Kiefer, Eric J.; Prete, James J.

    1998-01-01

    Purpose: To establish the rate of resolution of prostatic edema following transperineal interstitial permanent prostate brachytherapy, and to determine the results and impact of timing of the postimplant assessment on the dose-volume relationship. Methods and Materials: A series of 19 consecutive patients with early-stage adenocarcinoma of the prostate receiving transperineal interstitial permanent prostate brachytherapy, were enrolled in this study. Twelve received 125 I and seven received 103 Pd. Postoperative assessment included a computed tomographic (CT) scan on postoperative days 1, 8, 30, 90, and 180. On each occasion, CT scans were performed on a GE helical unit at 3-mm abutting slices, 15-cm field of view. Prostate volumes were outlined on CT scans by a single clinician. Following digitization of the volumes and radioactive sources, volumes and dose-volume histograms were calculated. The prostate volume encompassed by the 80% and 100% reference isodose volumes was calculated. Results: Preimplant transrectal ultrasound determined volumes varied from 17.5 to 38.6 cc (median 27.9 cc). Prostate volumes previously defined on 40 randomly selected postimplant CT scans were compared in a blinded fashion to a second CT-derived volume and ranged from -32% to +24%. The Pearson correlation coefficient for prostate CT volume reproducibility was 0.77 (p < 0.03). CT scan-determined volume performed on postoperative day 1 was an average of 41.4% greater than the volume determined by preimplant ultrasound. Significant decreases in average volume were seen during the first month postoperatively. Average volume decreased 14% from day 1 to day 8, 10% from day 8 to day 30, 3% from day 30 to day 90, and 2% thereafter. Coverage of the prostate volume by the 80% isodose volume increased from 85.6% on postoperative day 1 to 92.2% on postoperative day 180. The corresponding increase in the 100% reference dose coverage of the prostate volume ranged from 73.1% to 83.3% between

  12. Prediction of pavement remaining service life based on repetition of load and permanent deformation

    Science.gov (United States)

    Usman, R. S.; Setyawan, A.; Suprapto, M.

    2018-03-01

    One of the methods which was applied in the assessment of flexible pavement performance was mechanistic method assuming structures of road pavement to become multi-layer structure for flexible pavement, that the vehicle load working on the pavement layer under repetition with power failure worth 1 (one) unit which was assumed as evenly distributed static load, and therefore the pavement material would provide response in the form of stress, strain, and deflection. This is closely related in order to assess the structure of flexible pavement and to predict the remaining service life on the roads of Pulau Indah sta 0 + 000 to sta. 0 + 845 in Kota Kupang, Nusa Tenggara Timur. The performance appraisal indicator which was used was fatigue cracking happening bottom of the asphalt layer and permanent deformation (rutting) on the surface of subgrade. The strain estimate on the flexible pavement layer structure needs carefulness and high accuracy and therefore a software like KENPAVE which produces horizontal tensile strain of 8,802E-05 and vertical compressive strain of 2,642E-04 was used. By applying equation of The Asphalt Instituteit was obtained repetition of permit load when reaching fatigue cracking (Nf) was 16.071.516 ESAL and permanent deformation (rutting) was 14.703.867 ESAL and also it was predicted the remaining service life of pavement applied the equation of AASTHO 1993 by considering Traffic Multiplier factor (TM 1.8, TM 1.9 and TM 2.0) obtained the remaining life service due to fatigue of 5.51% in the year of 13th (TM 1.8), 7.95% in the year of12th (TM 1.9) and 3.11% (TM 2.0) in the year of 12th, also the remaining service life due to rutting of 4.69% in the year of 12th(TM 1.8), 7.79% in the year of 11th (TM 1.9), and 2.94 in the year of 11th (TM 2.0).

  13. A Vertical Flux-Switching Permanent Magnet Based Oscillating Wave Power Generator with Energy Storage

    Directory of Open Access Journals (Sweden)

    Yu Zou

    2017-06-01

    Full Text Available In this paper, an effective low-speed oscillating wave power generator and its energy storage system have been proposed. A vertical flux-switching permanent magnet (PM machine is designed as the generator while supercapacitors and batteries are used to store the energy. First, the overall power generation system is established and principles of the machine are introduced. Second, three modes are proposed for the energy storage system and sliding mode control (SMC is employed to regulate the voltage of the direct current (DC bus, observe the mechanical input, and feedback the status of the storage system. Finally, experiments with load and sinusoidal mechanical inputs are carried out to validate the effectiveness and stability of power generation for wave energy. The results show that the proposed power generation system can be employed in low-speed environment around 1 m/s to absorb random wave power, achieving over 60% power efficiency. The power generation approach can be used to capture wave energy in the future.

  14. A Steel Wire Stress Measuring Sensor Based on the Static Magnetization by Permanent Magnets

    Directory of Open Access Journals (Sweden)

    Dongge Deng

    2016-10-01

    Full Text Available A new stress measuring sensor is proposed to evaluate the axial stress in steel wires. Without using excitation and induction coils, the sensor mainly consists of a static magnetization unit made of permanent magnets and a magnetic field measurement unit containing Hall element arrays. Firstly, the principle is illustrated in detail. Under the excitation of the magnetization unit, a spatially varying magnetized region in the steel wire is utilized as the measurement region. Radial and axial magnetic flux densities at different lift-offs in this region are measured by the measurement unit to calculate the differential permeability curve and magnetization curve. Feature parameters extracted from the curves are used to evaluate the axial stress. Secondly, the special stress sensor for Φ5 and Φ7 steel wires is developed accordingly. At last, the performance of the sensor is tested experimentally. Experimental results show that the sensor can measure the magnetization curve accurately with the error in the range of ±6%. Furthermore, the obtained differential permeability at working points 1200 A/m and 10000 A/m change almost linearly with the stress in steel wires, the goodness of linear fits are all higher than 0.987. Thus, the proposed steel wire stress measuring sensor is feasible.

  15. Biologically based treatment of immature permanent teeth with pulpal necrosis: a case series.

    Science.gov (United States)

    Jung, Il-Young; Lee, Seung-Jong; Hargreaves, Kenneth M

    2012-06-01

    This case series reports the outcomes of 8 patients (ages 9-4 years) who presented with 9 immature permanent teeth with pulpal necrosis and apical periodontitis. During treatment, 5 of the teeth were found to have at least some residual vital tissue remaining in the root canal systems. After NaOCI irrigation and medication with ciprofloxacin, metronidazole, and minocycline, these teeth were sealed with mineral trioxide aggregate and restored. The other group of 4 teeth had no evidence of any residual vital pulp tissue. This second group of teeth was treated with NaOCl irrigation and medicated with ciprofloxacin, metronidazole, and minocycline followed by a revascularization procedure adopted from the trauma literature (bleeding evoked to form an intracanal blood clot). In both groups of patients, there was evidence of satisfactory postoperative clinical outcomes (1-5 years); the patients were asymptomatic, no sinus tracts were evident, apical periodontitis was resolved, and there was radiographic evidence of continuing thickness of dentinal walls, apical closure, or increased root length.

  16. Adjustable, short focal length permanent-magnet quadrupole based electron beam final focus system

    Directory of Open Access Journals (Sweden)

    J. K. Lim

    2005-07-01

    Full Text Available Advanced high-brightness beam applications such as inverse-Compton scattering (ICS depend on achieving of ultrasmall spot sizes in high current beams. Modern injectors and compressors enable the production of high-brightness beams having needed short bunch lengths and small emittances. Along with these beam properties comes the need to produce tighter foci, using stronger, shorter focal length optics. An approach to creating such strong focusing systems using high-field, small-bore permanent-magnet quadrupoles (PMQs is reported here. A final-focus system employing three PMQs, each composed of 16 neodymium iron boride sectors in a Halbach geometry has been installed in the PLEIADES ICS experiment. The field gradient in these PMQs is 560   T/m, the highest ever reported in a magnetic optics system. As the magnets are of a fixed field strength, the focusing system is tuned by adjusting the position of the three magnets along the beam line axis, in analogy to familiar camera optics. This paper discusses the details of the focusing system, simulation, design, fabrication, and experimental procedure in creating ultrasmall beams at PLEIADES.

  17. Research on analytical model and design formulas of permanent magnetic bearings based on Halbach array with arbitrary segmented magnetized angle

    International Nuclear Information System (INIS)

    Wang, Nianxian; Wang, Dongxiong; Chen, Kuisheng; Wu, Huachun

    2016-01-01

    The bearing capacity of permanent magnetic bearings can be improved efficiently by using the Halbach array magnetization. However, the research on analytical model of Halbach array PMBs with arbitrary segmented magnetized angle has not been developed. The application of Halbach array PMBs has been limited by the absence of the analytical model and design formulas. In this research, the Halbach array PMBs with arbitrary segmented magnetized angle has been studied. The magnetization model of bearings is established. The magnetic field distribution model of the permanent magnet array is established by using the scalar magnetic potential model. On the basis of this, the bearing force model and the bearing stiffness model of the PMBs are established based on the virtual displacement method. The influence of the pair of magnetic rings in one cycle and the structure parameters of PMBs on the maximal bearing capacity and support stiffness characteristics are studied. The reference factors for the design process of PMBs have been given. Finally, the theoretical model and the conclusions are verified by the finite element analysis.

  18. Accurate torque-sensorless control approach for interior permanent-magnet synchronous machine based on cascaded sliding mode observer

    Directory of Open Access Journals (Sweden)

    Kai-Hui Zhao

    2017-06-01

    Full Text Available To improve the accuracy of torque control for vector control of interior permanent-magnet synchronous machine (IPMSM, this study proposes a torque-sensorless control method based on cascaded sliding mode observer (SMO. First, the active flux model is discussed, which converts the model of IPMSM into the equivalent model of surface-mounted permanent-magnet synchronous machine. Second, to reduce chattering caused by system parameters variations and external disturbances, the cascaded observer is designed, which is composed of a variable gain adaptive SMO and an active flux SMO. The variable gain adaptive SMO is designed to estimate the speed, rotor position and stator resistance in the d–q reference frame. The active flux SMO is designed to estimate the active flux and torque in the α–β reference frame. Global asymptotic stability of the observers is guaranteed by the Lyapunov stability analysis. Finally, simulations and experiments are carried out to verify the effectiveness of the proposed control scheme.

  19. Tetragonal Ce-based Ce-Sm(Fe, Co, Ti){sub 12} alloys for permanent magnets

    Energy Technology Data Exchange (ETDEWEB)

    Martin-Cid, Andres; Salazar, Daniel [BCMaterials, Bizkaia Science and Tecnology Park, 48160 Derio (Spain); Gabay, Aleksandr M.; Hadjipanayis, George C. [Department of Physics and Astronomy, University of Delaware, Newark, DE, 19716 (United States); Barandiaran, Jose Manuel [BCMaterials, Bizkaia Science and Tecnology Park, 48160 Derio (Spain); Department of Electricity and Electronics, University Basque Country (UPV/EHU), 48080 Bilbao (Spain)

    2016-12-15

    Abundance and relatively low cost of Ce provide a great incentive for its use in rare-earth permanent magnets. It has been recently reported that the tetragonal Ce(Fe,Co,Ti)12 compounds may exhibit application-worthy intrinsic magnetic properties. In this work the effect of the α-Fe phase formation due to the evaporation of Sm during alloy fabrication has been studied, as a previous step in the attempt to convert the intrinsic magnetic properties into functional properties of a permanent magnet. Ce{sub 0.5}Sm{sub 0.5}Fe{sub 9}Co{sub 2}Ti alloys based on the ThMn12-type crystal structure have been synthesized via melt-spinning with different Sm content. Coercive fields between 2.8 and 1.4 kOe have been found for α-Fe phase contents between 8 and 46% in volume, showing the influence of the α-Fe phase on the coercivity and exchange coupling between the hard and soft phase. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Cross-sectional Internet-based survey of Japanese permanent daytime workers' sleep and daily rest periods.

    Science.gov (United States)

    Ikeda, Hiroki; Kubo, Tomohide; Sasaki, Takeshi; Liu, Xinxin; Matsuo, Tomoaki; So, Rina; Matsumoto, Shun; Yamauchi, Takashi; Takahashi, Masaya

    2018-05-25

    This study aimed to describe the sleep quantity, sleep quality, and daily rest periods (DRPs) of Japanese permanent daytime workers. Information about the usual DRP, sleep quantity, and sleep quality (Japanese version of the Pittsburgh Sleep Quality Index: PSQI-J) of 3,867 permanent daytime workers in Japan was gathered through an Internet-based survey. This information was analyzed and divided into the following eight DRP groups: <10, 10, 11, 12, 13, 14, 15, and ≥16 h. The sleep durations for workers in the <10, 10, 11, 12, 13, 14, 15, and ≥16 h DRP groups were found to be 5.3, 5.9, 6.1, 6.3, 6.5, 6.7, 6.7, and 6.9 h, respectively. The trend analysis revealed a significant linear trend as the shorter the DRP, the shorter was the sleep duration. The PSQI-J scores for the <10, 10, 11, 12, 13, 14, 15, and ≥16 h DRP groups were 7.1, 6.7, 6.7, 6.3, 6.0 (5.999), 5.6, 5.2, and 5.2, respectively. The trend analysis revealed a significant linear trend as the shorter the DRP, the lower was the sleep quality. This study described sleep quantity, sleep quality, and DRP in Japanese daytime workers. It was found that a shorter DRP was associated with poorer sleep quantity as well as quality.

  1. Model reference adaptive control (MRAC)-based parameter identification applied to surface-mounted permanent magnet synchronous motor

    Science.gov (United States)

    Zhong, Chongquan; Lin, Yaoyao

    2017-11-01

    In this work, a model reference adaptive control-based estimated algorithm is proposed for online multi-parameter identification of surface-mounted permanent magnet synchronous machines. By taking the dq-axis equations of a practical motor as the reference model and the dq-axis estimation equations as the adjustable model, a standard model-reference-adaptive-system-based estimator was established. Additionally, the Popov hyperstability principle was used in the design of the adaptive law to guarantee accurate convergence. In order to reduce the oscillation of identification result, this work introduces a first-order low-pass digital filter to improve precision regarding the parameter estimation. The proposed scheme was then applied to an SPM synchronous motor control system without any additional circuits and implemented using a DSP TMS320LF2812. For analysis, the experimental results reveal the effectiveness of the proposed method.

  2. Fractional order sliding-mode control based on parameters auto-tuning for velocity control of permanent magnet synchronous motor.

    Science.gov (United States)

    Zhang, BiTao; Pi, YouGuo; Luo, Ying

    2012-09-01

    A fractional order sliding mode control (FROSMC) scheme based on parameters auto-tuning for the velocity control of permanent magnet synchronous motor (PMSM) is proposed in this paper. The control law of the proposed F(R)OSMC scheme is designed according to Lyapunov stability theorem. Based on the property of transferring energy with adjustable type in F(R)OSMC, this paper analyzes the chattering phenomenon in classic sliding mode control (SMC) is attenuated with F(R)OSMC system. A fuzzy logic inference scheme (FLIS) is utilized to obtain the gain of switching control. Simulations and experiments demonstrate that the proposed FROSMC not only achieve better control performance with smaller chatting than that with integer order sliding mode control, but also is robust to external load disturbance and parameter variations. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

  3. Definition of medical event is to be based on the total source strength for evaluation of permanent prostate brachytherapy: A report from the American Society for Radiation Oncology.

    Science.gov (United States)

    Nag, Subir; Demanes, D Jeffrey; Hagan, Michael; Rivard, Mark J; Thomadsen, Bruce R; Welsh, James S; Williamson, Jeffrey F

    2011-10-01

    The Nuclear Regulatory Commission deems it to be a medical event (ME) if the total dose delivered differs from the prescribed dose by 20% or more. A dose-based definition of ME is not appropriate for permanent prostate brachytherapy as it generates too many spurious MEs and thereby creates unnecessary apprehension in patients, and ties up regulatory bodies and the licensees in unnecessary and burdensome investigations. A more suitable definition of ME is required for permanent prostate brachytherapy. The American Society for Radiation Oncology (ASTRO) formed a working group of experienced clinicians to review the literature, assess the validity of current regulations, and make specific recommendations about the definition of an ME in permanent prostate brachytherapy. The working group found that the current definition of ME in §35.3045 as "the total dose delivered differs from the prescribed dose by 20 percent or more" was not suitable for permanent prostate brachytherapy since the prostate volume (and hence the resultant calculated prostate dose) is dependent on the timing of the imaging, the imaging modality used, the observer variability in prostate contouring, the planning margins used, inadequacies of brachytherapy treatment planning systems to calculate tissue doses, and seed migration within and outside the prostate. If a dose-based definition for permanent implants is applied strictly, many properly executed implants would be improperly classified as an ME leading to a detrimental effect on brachytherapy. The working group found that a source strength-based criterion, of >20% of source strength prescribed in the post-procedure written directive being implanted outside the planning target volume is more appropriate for defining ME in permanent prostate brachytherapy. ASTRO recommends that the definition of ME for permanent prostate brachytherapy should not be dose based but should be based upon the source strength (air-kerma strength) administered.

  4. Basing assessment and treatment of problem behavior on behavioral momentum theory: Analyses of behavioral persistence.

    Science.gov (United States)

    Schieltz, Kelly M; Wacker, David P; Ringdahl, Joel E; Berg, Wendy K

    2017-08-01

    The connection, or bridge, between applied and basic behavior analysis has been long-established (Hake, 1982; Mace & Critchfield, 2010). In this article, we describe how clinical decisions can be based more directly on behavioral processes and how basing clinical procedures on behavioral processes can lead to improved clinical outcomes. As a case in point, we describe how applied behavior analyses of maintenance, and specifically the long-term maintenance of treatment effects related to problem behavior, can be adjusted and potentially enhanced by basing treatment on Behavioral Momentum Theory. We provide a brief review of the literature including descriptions of two translational studies that proposed changes in how differential reinforcement of alternative behavior treatments are conducted based on Behavioral Momentum Theory. We then describe current clinical examples of how these translations are continuing to impact the definitions, designs, analyses, and treatment procedures used in our clinical practice. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Nonlinear Dynamic Surface Control of Chaos in Permanent Magnet Synchronous Motor Based on the Minimum Weights of RBF Neural Network

    Directory of Open Access Journals (Sweden)

    Shaohua Luo

    2014-01-01

    Full Text Available This paper is concerned with the problem of the nonlinear dynamic surface control (DSC of chaos based on the minimum weights of RBF neural network for the permanent magnet synchronous motor system (PMSM wherein the unknown parameters, disturbances, and chaos are presented. RBF neural network is used to approximate the nonlinearities and an adaptive law is employed to estimate unknown parameters. Then, a simple and effective controller is designed by introducing dynamic surface control technique on the basis of first-order filters. Asymptotically tracking stability in the sense of uniformly ultimate boundedness is achieved in a short time. Finally, the performance of the proposed controller is testified through simulation results.

  6. Sensorless control of ship propulsion interior permanent magnet synchronous motor based on a new sliding mode observer.

    Science.gov (United States)

    Ren, Jun-Jie; Liu, Yan-Cheng; Wang, Ning; Liu, Si-Yuan

    2015-01-01

    This paper proposes a sensorless speed control strategy for ship propulsion interior permanent magnet synchronous motor (IPMSM) based on a new sliding-mode observer (SMO). In the SMO the low-pass filter and the method of arc-tangent calculation of extended electromotive force (EMF) or phase-locked loop (PLL) technique are not used. The calculation of the rotor speed is deduced from the Lyapunov function stability analysis. In order to reduce system chattering, sigmoid functions with switching gains being adaptively updated by fuzzy logic systems are innovatively incorporated into the SMO. Finally, simulation results for a 4.088 MW ship propulsion IPMSM and experimental results from a 7.5 kW IPMSM drive are provided to verify the effectiveness of the proposed SMO method. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

  7. Dynamic modeling of wind turbine based axial flux permanent magnetic synchronous generator connected to the grid with switch reduced converter

    Directory of Open Access Journals (Sweden)

    Ali Reza Dehghanzadeh

    2018-03-01

    Full Text Available This paper studies the power electronic converters for grid connection of axial flux permanent magnetic synchronous generators (AFPMSG based variable speed wind turbine. In this paper, a new variable speed wind turbine with AFPMSG and Z-source inverter is proposed to improve number of switches and topology reliability. Besides, dynamic modeling of AFPMSG is presented to analyze grid connection of the proposed topology. The Z-source inverter controls maximum power point tracking (MPPT and delivering power to the grid. Therefore other DC–DC chopper is not required to control the rectified output voltage of generator in view of MPPT. As a result, the proposed topology requires less power electronic switches and the suggested system is more reliable against short circuit. The ability of proposed energy conversion system with AFPMSG is validated with simulation results and experimental results using PCI-1716 data acquisition system.

  8. Brachytherapy optimization using radiobiological-based planning for high dose rate and permanent implants for prostate cancer treatment

    Science.gov (United States)

    Seeley, Kaelyn; Cunha, J. Adam; Hong, Tae Min

    2017-01-01

    We discuss an improvement in brachytherapy--a prostate cancer treatment method that directly places radioactive seeds inside target cancerous regions--by optimizing the current standard for delivering dose. Currently, the seeds' spatiotemporal placement is determined by optimizing the dose based on a set of physical, user-defined constraints. One particular approach is the ``inverse planning'' algorithms that allow for tightly fit isodose lines around the target volumes in order to reduce dose to the patient's organs at risk. However, these dose distributions are typically computed assuming the same biological response to radiation for different types of tissues. In our work, we consider radiobiological parameters to account for the differences in the individual sensitivities and responses to radiation for tissues surrounding the target. Among the benefits are a more accurate toxicity rate and more coverage to target regions for planning high-dose-rate treatments as well as permanent implants.

  9. Eddy current loss analysis of open-slot fault-tolerant permanent-magnet machines based on conformal mapping method

    Science.gov (United States)

    Ji, Jinghua; Luo, Jianhua; Lei, Qian; Bian, Fangfang

    2017-05-01

    This paper proposed an analytical method, based on conformal mapping (CM) method, for the accurate evaluation of magnetic field and eddy current (EC) loss in fault-tolerant permanent-magnet (FTPM) machines. The aim of modulation function, applied in CM method, is to change the open-slot structure into fully closed-slot structure, whose air-gap flux density is easy to calculate analytically. Therefore, with the help of Matlab Schwarz-Christoffel (SC) Toolbox, both the magnetic flux density and EC density of FTPM machine are obtained accurately. Finally, time-stepped transient finite-element method (FEM) is used to verify the theoretical analysis, showing that the proposed method is able to predict the magnetic flux density and EC loss precisely.

  10. Condition monitoring approach for permanent magnet synchronous motor drives based on the INFORM method

    OpenAIRE

    Arellano-Padilla, J.; Sumner, M.; Gerada, C.

    2016-01-01

    This paper proposes a monitoring scheme based on saliency tracking to assess the health condition of PMSM drives operating under non stationary conditions. The evaluated scheme is based on the INFORM methodology, which is associated to the accurate sensorless control of PM drives without zero speed limitation. The result is a monitoring scheme that is able to detect faults that would be very difficult to evaluate under nonstationary conditions. A relevant aspect of the proposed scheme is that...

  11. Fault tolerant control with torque limitation based on fault mode for ten-phase permanent magnet synchronous motor

    Directory of Open Access Journals (Sweden)

    Guo Hong

    2015-10-01

    Full Text Available This paper proposes a novel fault tolerant control with torque limitation based on the fault mode for the ten-phase permanent magnet synchronous motor (PMSM under various open-circuit and short-circuit fault conditions, which includes the optimal torque control and the torque limitation control based on the fault mode. The optimal torque control is adopted to guarantee the ripple-free electromagnetic torque operation for the ten-phase motor system under the post-fault condition. Furthermore, we systematically analyze the load capacity of the ten-phase motor system under different fault modes. And a torque limitation control approach based on the fault mode is proposed, which was not available earlier. This approach is able to ensure the safety operation of the faulted motor system in long operating time without causing the overheat fault. The simulation result confirms that the proposed fault tolerant control for the ten-phase motor system is able to guarantee the ripple-free electromagnetic torque and the safety operation in long operating time under the normal and fault conditions.

  12. Essure Permanent Birth Control

    Science.gov (United States)

    ... Prosthetics Essure Permanent Birth Control Essure Permanent Birth Control Share Tweet Linkedin Pin it More sharing options ... Print Essure is a a permanently implanted birth control device for women (female sterilization). Implantation of Essure ...

  13. Force measurements on a shielded coreless linear permanent magnet motor

    NARCIS (Netherlands)

    Pluk, K.J.W.; Jansen, J.W.; Lomonova, E.A.

    2014-01-01

    This paper compares force measurements on a shielded coreless linear permanent magnet motor with 2-D models. A 2-D semianalytical modeling method is applied, which is based on Fourier modeling and includes force calculations. The semianalytical modeling correctly predicts the behavior found in the

  14. Phase composition and magnetic properties in nanocrystalline permanent magnets based on misch-metal

    Science.gov (United States)

    Ma, Q.; Wang, J.; Zhang, Z. Y.; Zhang, X. F.; Liu, F.; Liu, Y. L.; Jv, X. M.; Li, Y. F.; Wang, G. F.

    2017-09-01

    The magnetic properties and phase composition of magnets based on misch-metal (MM) with nominal composition of MM13+xFe84-xB6.5 with x = 0.5, 1, 1.5, 2 and 2.5 using melt-spinning method were investigated. For x = 1.5, it could exhibit best magnetic properties (Hcj = 753.02 kA m-1, (BH)max = 70.77 kJ m-3). X-ray diffraction and energy dispersive spectroscopy show that the multi hard magnetic phase of RE2Fe14B (RE = La, Ce, Pr, Nd) existed in the magnets. The domain wall pinning effect and the exchange coupling interaction between grains are dependent on the abnormal RE-rich phase composition. Optimizing the phase constitution is necessary to improve magnetic properties in MM-Fe-B magnets for utilizing the rare earth resource in a balanced manner.

  15. Modeling and simulation of grid connected permanent magnet generator based small wind energy conversion systems

    Energy Technology Data Exchange (ETDEWEB)

    Arifujjaman, Md.

    2011-07-01

    In order to recover the maximum energy from small scale wind turbine systems many parameters have to be controlled. The aim of this paper is to propose a control strategy for the grid connected PMG-based small wind turbine systems. A mathematical model of small wind turbine systems was developed and the system simulated. Results show demonstrated that the control strategy is highly efficient. Sure enough it reduces the dependence on system variables, diminishes the system complexity, its furling and maximum power point controllers are efficient and it provides a stable operation for multiple wind speeds. This study developed a modeling and control strategy which was proved to be feasible by simulation results.

  16. An orientation measurement method based on Hall-effect sensors for permanent magnet spherical actuators with 3D magnet array.

    Science.gov (United States)

    Yan, Liang; Zhu, Bo; Jiao, Zongxia; Chen, Chin-Yin; Chen, I-Ming

    2014-10-24

    An orientation measurement method based on Hall-effect sensors is proposed for permanent magnet (PM) spherical actuators with three-dimensional (3D) magnet array. As there is no contact between the measurement system and the rotor, this method could effectively avoid friction torque and additional inertial moment existing in conventional approaches. Curved surface fitting method based on exponential approximation is proposed to formulate the magnetic field distribution in 3D space. The comparison with conventional modeling method shows that it helps to improve the model accuracy. The Hall-effect sensors are distributed around the rotor with PM poles to detect the flux density at different points, and thus the rotor orientation can be computed from the measured results and analytical models. Experiments have been conducted on the developed research prototype of the spherical actuator to validate the accuracy of the analytical equations relating the rotor orientation and the value of magnetic flux density. The experimental results show that the proposed method can measure the rotor orientation precisely, and the measurement accuracy could be improved by the novel 3D magnet array. The study result could be used for real-time motion control of PM spherical actuators.

  17. Classification Method to Define Synchronization Capability Limits of Line-Start Permanent-Magnet Motor Using Mesh-Based Magnetic Equivalent Circuit Computation Results

    Directory of Open Access Journals (Sweden)

    Bart Wymeersch

    2018-04-01

    Full Text Available Line start permanent magnet synchronous motors (LS-PMSM are energy-efficient synchronous motors that can start asynchronously due to a squirrel cage in the rotor. The drawback, however, with this motor type is the chance of failure to synchronize after start-up. To identify the problem, and the stable operation limits, the synchronization at various parameter combinations is investigated. For accurate knowledge of the operation limits to assure synchronization with the utility grid, an accurate classification of parameter combinations is needed. As for this, many simulations have to be executed, a rapid evaluation method is indispensable. To simulate the dynamic behavior in the time domain, several modeling methods exist. In this paper, a discussion is held with respect to different modeling methods. In order to include spatial factors and magnetic nonlinearities, on the one hand, and to restrict the computation time on the other hand, a magnetic equivalent circuit (MEC modeling method is developed. In order to accelerate numerical convergence, a mesh-based analysis method is applied. The novelty in this paper is the implementation of support vector machine (SVM to classify the results of simulations at various parameter combinations into successful or unsuccessful synchronization, in order to define the synchronization capability limits. It is explained how these techniques can benefit the simulation time and the evaluation process. The results of the MEC modeling correspond to those obtained with finite element analysis (FEA, despite the reduced computation time. In addition, simulation results obtained with MEC modeling are experimentally validated.

  18. Automated classification of Permanent Scatterers time-series based on statistical characterization tests

    Science.gov (United States)

    Berti, Matteo; Corsini, Alessandro; Franceschini, Silvia; Iannacone, Jean Pascal

    2013-04-01

    The application of space borne synthetic aperture radar interferometry has progressed, over the last two decades, from the pioneer use of single interferograms for analyzing changes on the earth's surface to the development of advanced multi-interferogram techniques to analyze any sort of natural phenomena which involves movements of the ground. The success of multi-interferograms techniques in the analysis of natural hazards such as landslides and subsidence is widely documented in the scientific literature and demonstrated by the consensus among the end-users. Despite the great potential of this technique, radar interpretation of slope movements is generally based on the sole analysis of average displacement velocities, while the information embraced in multi interferogram time series is often overlooked if not completely neglected. The underuse of PS time series is probably due to the detrimental effect of residual atmospheric errors, which make the PS time series characterized by erratic, irregular fluctuations often difficult to interpret, and also to the difficulty of performing a visual, supervised analysis of the time series for a large dataset. In this work is we present a procedure for automatic classification of PS time series based on a series of statistical characterization tests. The procedure allows to classify the time series into six distinctive target trends (0=uncorrelated; 1=linear; 2=quadratic; 3=bilinear; 4=discontinuous without constant velocity; 5=discontinuous with change in velocity) and retrieve for each trend a series of descriptive parameters which can be efficiently used to characterize the temporal changes of ground motion. The classification algorithms were developed and tested using an ENVISAT datasets available in the frame of EPRS-E project (Extraordinary Plan of Environmental Remote Sensing) of the Italian Ministry of Environment (track "Modena", Northern Apennines). This dataset was generated using standard processing, then the

  19. An Optimal Integrated Control Scheme for Permanent Magnet Synchronous Generator-Based Wind Turbines under Asymmetrical Grid Fault Conditions

    Directory of Open Access Journals (Sweden)

    Dan Wang

    2016-04-01

    Full Text Available In recent years, the increasing penetration level of wind energy into power systems has brought new issues and challenges. One of the main concerns is the issue of dynamic response capability during outer disturbance conditions, especially the fault-tolerance capability during asymmetrical faults. In order to improve the fault-tolerance and dynamic response capability under asymmetrical grid fault conditions, an optimal integrated control scheme for the grid-side voltage-source converter (VSC of direct-driven permanent magnet synchronous generator (PMSG-based wind turbine systems is proposed in this paper. The optimal control strategy includes a main controller and an additional controller. In the main controller, a double-loop controller based on differential flatness-based theory is designed for grid-side VSC. Two parts are involved in the design process of the flatness-based controller: the reference trajectories generation of flatness output and the implementation of the controller. In the additional control aspect, an auxiliary second harmonic compensation control loop based on an improved calculation method for grid-side instantaneous transmission power is designed by the quasi proportional resonant (Quasi-PR control principle, which is able to simultaneously restrain the second harmonic components in active power and reactive power injected into the grid without the respective calculation for current control references. Moreover, to reduce the DC-link overvoltage during grid faults, the mathematical model of DC-link voltage is analyzed and a feedforward modified control factor is added to the traditional DC voltage control loop in grid-side VSC. The effectiveness of the optimal control scheme is verified in PSCAD/EMTDC simulation software.

  20. Behavioral interventions for office-based care: behavior change.

    Science.gov (United States)

    Delfino, Matthew; Larzelere, Michele McCarthy

    2014-03-01

    Family physicians play an important role in identifying and treating the behavioral etiologies of morbidity and mortality. Changing behavior is a challenging process that begins with identifying a patient's readiness to change. Interventions, such as motivational interviewing, are used to increase a patient's desire to change, and cognitive behavioral therapy can be initiated to increase a patient's likelihood of change, particularly if barriers are identified. After patients embark on change, family physicians are uniquely positioned to connect them to self-help programs, more intensive psychotherapy, and newer technology-based support programs, and to provide repeated, brief, positive reinforcement. Specific behavioral interventions that can be effective include computerized smoking cessation programs; electronic reminders and support delivered by family physicians or other clinicians for weight loss; linkage to community-based programs for seniors; increased length and demands of in-school programs to support exercise participation by children; and access reduction education to prevent firearm injury. Written permission from the American Academy of Family Physicians is required for reproduction of this material in whole or in part in any form or medium.

  1. Construction of permanently inducible miRNA-based expression vectors using site-specific recombinases

    Directory of Open Access Journals (Sweden)

    Garwick-Coppens Sara E

    2011-11-01

    Full Text Available Abstract Background RNA interference (RNAi is a conserved gene silencing mechanism mediated by small inhibitory microRNAs (miRNAs. Promoter-driven miRNA expression vectors have emerged as important tools for delivering natural or artificially designed miRNAs to eukaryotic cells and organisms. Such systems can be used to query the normal or pathogenic functions of natural miRNAs or messenger RNAs, or to therapeutically silence disease genes. Results As with any molecular cloning procedure, building miRNA-based expression constructs requires a time investment and some molecular biology skills. To improve efficiency and accelerate the construction process, we developed a method to rapidly generate miRNA expression vectors using recombinases instead of more traditional cut-and-paste molecular cloning techniques. In addition to streamlining the construction process, our cloning strategy provides vectors with added versatility. In our system, miRNAs can be constitutively expressed from the U6 promoter, or inducibly expressed by Cre recombinase. We also engineered a built-in mechanism to destroy the vector with Flp recombinase, if desired. Finally, to further simplify the construction process, we developed a software package that automates the prediction and design of optimal miRNA sequences using our system. Conclusions We designed and tested a modular system to rapidly clone miRNA expression cassettes. Our strategy reduces the hands-on time required to successfully generate effective constructs, and can be implemented in labs with minimal molecular cloning expertise. This versatile system provides options that permit constitutive or inducible miRNA expression, depending upon the needs of the end user. As such, it has utility for basic or translational applications.

  2. Supporting smartphone-based behavioral activation

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Rohani, Darius A.; Tuxen, Nanna

    2017-01-01

    Behavioral activation has shown to be a simple yet efective therapy for depressive patients. The method relies on extensive collection of patient reported activity data on an hourly basis. We are currently in the process of designing a smartphone-based behavioral activation system for depressive...... disorders. However, it is an open question to what degree patients would use this approach given the high demand for user input. In order to investigate this question, we collected paper-based behavioral activation forms from 5 patients, covering in total 18 weeks, 115 days, and 1,614 hours of self......-reported activity data. In this paper we present an analysis of this data and discuss the implications for the design of a smartphone-based system for behavioral activation....

  3. THE INFLUENCE OF PERCEIVED ORGANIZATIONAL SUPPORT, JOB SATISFACTION AND ORGANIZATIONAL COMMITMENT TOWARD ORGANIZATIONAL CITIZENSHIP BEHAVIOR (A Study of the Permanent Lecturers at University of Lambung Mangkurat, Banjarmasin

    Directory of Open Access Journals (Sweden)

    Meiske Claudia

    2018-01-01

    Full Text Available The population in this research is all of the permanent lecturers employed at University of Lambung Mangkurat (ULM. The respondents are taken from 4 academic ranks, which are represented by Asisten Ahli (Instructor, Lektor (Assistant Professor, Lektor Kepala (Associate Professor, and Guru Besar (Professor. One hundred and thirty samples were collected by using a proportional-stratified random sampling method. A Partial Least Square (PLS method was used to analyze the data. The results showed that lecturers with a positive perception of the organizational support available to them feel more satisfied with their job, which in turn encourages the creation of a high organizational commitment and results in the emergence of positive organizational citizenship behavior (OCB. These study’s results showed us the application of social exchange theory and organizational support theory in a higher educational institution. The findings of this study are considered to be important, as they provide additional empirical evidence regarding the importance of organizational support as a basis for improving the ULM lecturers' job satisfaction, organizational commitment, and OCB. The implications and further research are also discussed.

  4. Control strategy of wind turbine based on permanent magnet synchronous generator and energy storage for stand-alone systems

    DEFF Research Database (Denmark)

    Deng, Fujin; Liu, Dong; Chen, Zhe

    2017-01-01

    This paper investigates a variable speed wind turbine based on permanent magnet synchronous generator and a full-scale power converter in a stand-alone system. An energy storage system(ESS) including battery and fuel cell-electrolyzer combination is connected to the DC link of the full-scale power...... converter through the power electronics interface. Wind is the primary power source of the system, the battery and FC-electrolyzer combination is used as a backup and a long-term storage system to provide or absorb power in the stand-alone system, respectively. In this paper, a control strategy is proposed...... for the operation of this variable speed wind turbine in a stand-alone system, where the generator-side converter and the ESS operate together to meet the demand of the loads. This control strategy is competent for supporting the variation of the loads or wind speed and limiting the DC-link voltage of the full...

  5. A New Power-Factor-Based Vector Control Method for Sensorless Drive of Permanent-Magnet Synchronous Motors

    Science.gov (United States)

    Shinnaka, Shinji

    As a simple vector control method for sensorless drives of permanent-magnet synchronous motors, the so-called “Power-Factor-Based (PFB) Vector Control Method” has been proposed. The conventional PFB method directly estimates the phase of the quasi-optimal stator current through a control of the power factor phase, instead of the estimation of the rotor phase. The stator current is controlled in the current reference frame whose secondary axis phase is the same as the stator current phase. This paper proposes a new PEB method where the stator current is controlled in the voltage reference frame whose secondary axis phase is the same as the voltage phase rather than the current phase. It is shown that the similar quasi-optimal stator current control can be attained through the current control with appropriate current commands taking the power factor phase into account. This paper also shows a practical method for generating the current commands and a practical guideline for the design parameters of the new PFB method.

  6. Comparison of prostate contours between conventional stepping transverse imaging and Twister-based sagittal imaging in permanent interstitial prostate brachytherapy.

    Science.gov (United States)

    Kawakami, Shogo; Ishiyama, Hiromichi; Satoh, Takefumi; Tsumura, Hideyasu; Sekiguchi, Akane; Takenaka, Kouji; Tabata, Ken-Ichi; Iwamura, Masatsugu; Hayakawa, Kazushige

    2017-08-01

    To compare prostate contours on conventional stepping transverse image acquisitions with those on twister-based sagittal image acquisitions. Twenty prostate cancer patients who were planned to have permanent interstitial prostate brachytherapy were prospectively accrued. A transrectal ultrasonography probe was inserted, with the patient in lithotomy position. Transverse images were obtained with stepping movement of the transverse transducer. In the same patient, sagittal images were also obtained through rotation of the sagittal transducer using the "Twister" mode. The differences of prostate size among the two types of image acquisitions were compared. The relationships among the difference of the two types of image acquisitions, dose-volume histogram (DVH) parameters on the post-implant computed tomography (CT) analysis, as well as other factors were analyzed. The sagittal image acquisitions showed a larger prostate size compared to the transverse image acquisitions especially in the anterior-posterior (AP) direction ( p transverse image acquisitions was correlated to DVH parameters such as D 90 ( R = 0.518, p = 0.019), and V 100 ( R = 0.598, p = 0.005). There were small but significant differences in the prostate contours between the transverse and the sagittal planning image acquisitions. Furthermore, our study suggested that the differences between the two types of image acquisitions might correlated to dosimetric results on CT analysis.

  7. Adaptive two-degree-of-freedom PI for speed control of permanent magnet synchronous motor based on fractional order GPC.

    Science.gov (United States)

    Qiao, Wenjun; Tang, Xiaoqi; Zheng, Shiqi; Xie, Yuanlong; Song, Bao

    2016-09-01

    In this paper, an adaptive two-degree-of-freedom (2Dof) proportional-integral (PI) controller is proposed for the speed control of permanent magnet synchronous motor (PMSM). Firstly, an enhanced just-in-time learning technique consisting of two novel searching engines is presented to identify the model of the speed control system in a real-time manner. Secondly, a general formula is given to predict the future speed reference which is unavailable at the interval of two bus-communication cycles. Thirdly, the fractional order generalized predictive control (FOGPC) is introduced to improve the control performance of the servo drive system. Based on the identified model parameters and predicted speed reference, the optimal control law of FOGPC is derived. Finally, the designed 2Dof PI controller is auto-tuned by matching with the optimal control law. Simulations and real-time experimental results on the servo drive system of PMSM are provided to illustrate the effectiveness of the proposed strategy. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

  8. High performance permanent magnet materials

    International Nuclear Information System (INIS)

    Sankar, S.G.; Herbst, J.F.; Koon, N.C.

    1987-01-01

    This book contains 25 selections. Some of the titles are: Initial magnetization behavior of rapidly quenched neodymium-iron-boron magnets; Optimization of liquid dynamic compaction for Fe-Nd-B magnet alloys; Misch-metal and/or aluminum substitutions in Nd-Fe-B permanent magnets; and NdFeB magnets with improved temperature characteristics

  9. Superconducting permanent magnets

    International Nuclear Information System (INIS)

    Wipf, S.L.; Laquer, H.L.

    1989-01-01

    The concept of superconducting permanent magnets with fields trapped in shells or cylinders of Type II superconductors is an old one. Unfortunately, the low values of 0.5 to 1T for the first flux jump field, which is independent of the actual current density, have frustrated its implementation with classical Type II superconductors. The fact that the flux jump fields for high temperature superconductors should be an order of magnitude larger at liquid nitrogen temperatures allows us to reconsider these options. Analysis of the hysteresis patterns, based on the critical state model, shows that, if the dimensions are chosen so that the sample is penetrated at a field B/sub p/, which is equal to or just less than the first flux jump field, B/sub fj/, a temporarily applied field of 2B/sub fj/ will trap 0.5 B/sub fj/. Thus for a 90 K superconductor with a B/sub fj/ of 6T, a permanent field of 3 T should be trapped, with an energy product of 1.8 MJ/m/sup 3/ (225 MG . Oe). This is five times as large as for the best permanent magnet materials. The authors discuss means to verify the analysis and the limitations imposed by the low critical current densities in presently available high temperature superconductors

  10. Permanent resident

    Directory of Open Access Journals (Sweden)

    John F. Fisher

    2016-05-01

    Full Text Available The training of physicians in the past century was based primarily on responsibility and the chain-of-command. Those with the bulk of that responsibility in the fields of pediatrics and internal medicine were residents. Residents trained the medical students and supervised them carefully in caring for patients. Most attending physicians supervised their teams at arm's length, primarily serving as teachers of the finer points of diagnosis and treatment during set periods of the day or week with a perfunctory signature on write-ups or progress notes. Residents endeavored to protect the attending physician from being heavily involved unless they were unsure about a clinical problem. Before contacting the attending physician, a more senior resident would be called. Responsibility was the ultimate teacher. The introduction of diagnosis-related groups by the federal government dramatically changed the health care delivery system, placing greater emphasis on attending physician visibility in the medical record, ultimately resulting in more attending physician involvement in day-to-day care of patients in academic institutions. Without specified content in attending notes, hospital revenues would decline. Although always in charge technically, attending physicians increasingly have assumed the role once dominated by the resident. Using biographical experiences of more than 40 years, the author acknowledges and praises the educational role of responsibility in his own training and laments its declining role in today's students and house staff.

  11. Design of spoke type motor and magnetizer for improving efficiency based rare-earth-free permanent-magnet motor

    Science.gov (United States)

    Kim, Young Hyun; Cheon, Byung Chul; Lee, Jung Ho

    2018-05-01

    This study proposes criteria for both optimal-shape and magnetizer-system designs to be used for a high-output spoke-type motor. The study also examines methods of reducing high-cogging torque and torque ripple, to prevent noise and vibration. The optimal design of the stator and rotor can be enhanced using both a response surface method and finite element method. In addition, a magnetizer system is optimally designed for the magnetization of permanent magnets for use in the motor. Finally, this study verifies that the proposed motor can efficiently replace interior permanent magnet synchronous motor in many industries.

  12. Design of spoke type motor and magnetizer for improving efficiency based rare-earth-free permanent-magnet motor

    Directory of Open Access Journals (Sweden)

    Young Hyun Kim

    2018-05-01

    Full Text Available This study proposes criteria for both optimal-shape and magnetizer-system designs to be used for a high-output spoke-type motor. The study also examines methods of reducing high-cogging torque and torque ripple, to prevent noise and vibration. The optimal design of the stator and rotor can be enhanced using both a response surface method and finite element method. In addition, a magnetizer system is optimally designed for the magnetization of permanent magnets for use in the motor. Finally, this study verifies that the proposed motor can efficiently replace interior permanent magnet synchronous motor in many industries.

  13. Cold-Based Glaciation on Mercury: Accumulation and Flow of Ice in Permanently-Shadowed Circum-Polar Crater Interiors

    Science.gov (United States)

    Fastook, J. L.; Head, J. W.

    2018-05-01

    Examining the potential for dynamic flow of ice deposits in permanently-shadowed craters, it is determined that the cold environment of the polar craters yields very small velocities and deformation is minimal on a time scale of millions of years.

  14. Promoting work participation of non-permanent workers with psychological problems: An evidence-based approach to occupational health care

    NARCIS (Netherlands)

    Audhoe, S.S.

    2016-01-01

    Unemployed and temporary agency workers and workers with expired fixed-term contracts are a particularly vulnerable group, at risk for sickness absence and prolonged work disability due to psychological problems. These workers who are without an employment contract, are also known as non-permanent

  15. Fault ride-through and grid support of permanent magnet synchronous generator-based wind farms with HVAC and VSC-HVDC transmission systems

    DEFF Research Database (Denmark)

    Liu, Hongzhi; Chen, Zhe

    2012-01-01

    This paper describes fault ride-through and grid support of offshore wind farms based on permanent magnet synchronous generator (PMSG) wind turbines connected to the onshore AC network through two alternative transmission systems: high voltage AC (HVAC) or high voltage DC (HVDC) based on voltage...... source converters (VSC). The proposed configurations of the PMSG-based offshore wind farm and VSC-based HVDC are given as well as their control strategies under both steady state and fault state. The PMSG-based offshore wind farm is integrated into a test power transmission system via either HVAC or VSC...

  16. Experimental and micromagnetic first-order reversal curves analysis in NdFeB-based bulk 'exchange spring'-type permanent magnets

    Energy Technology Data Exchange (ETDEWEB)

    Chiriac, Horia [National Institute of Research and Development for Technical Physics, 47 Mangeron Boulevard, 700050, Iasi (Romania); Lupu, Nicoleta [National Institute of Research and Development for Technical Physics, 47 Mangeron Boulevard, 700050, Iasi (Romania); Stoleriu, Laurentiu [Al. I. Cuza University, Department of Solid State and Theoretical Physics, Blvd. Carol I, 11, 700506, Iasi (Romania)]. E-mail: lstoler@uaic.ro; Postolache, Petronel [Al. I. Cuza University, Department of Solid State and Theoretical Physics, Blvd. Carol I, 11, 700506, Iasi (Romania); Stancu, Alexandru [Al. I. Cuza University, Department of Solid State and Theoretical Physics, Blvd. Carol I, 11, 700506, Iasi (Romania)

    2007-09-15

    In this paper we present the results of applying the first-order reversal curves (FORC) diagram experimental method to the analysis of the magnetization processes of NdFeB-based permanents magnets. The FORC diagrams for this kind of exchange spring magnets show the existence of two magnetic phases-a soft magnetic phase and a hard magnetic one. Micromagnetic modeling is used for validating the hypotheses regarding the origin of the different features of the experimental FORC diagrams.

  17. Marxism as permanent revolution

    NARCIS (Netherlands)

    van Ree, E.

    2013-01-01

    This article argues that the 'permanent revolution' represented the dominant element in Karl Marx and Friedrich Engels' political discourse, and that it tended to overrule considerations encapsulated in 'historical materialism'. In Marx and Engels's understanding, permanent revolution did not

  18. Novel mechanisms for solid-state processing and grain growth with microstructure alignment in alnico-8 based permanent magnets

    Science.gov (United States)

    Kassen, Aaron G.; White, Emma M. H.; Hu, Liangfa; Tang, Wei; Zhou, Lin; Kramer, Matthew J.; Anderson, Iver E.

    2018-05-01

    An estimated 750,000 new hybrid electric and plug-in battery vehicles, most with permanent magnet synchronous alternating current (PMAC) drive motors, took to the road in 2016 alone. Accompanied by 40% year over year growth in the EV market significant challenges exist in producing large quantities of permanent magnets (on the order of tens of millions) for reliable, low-cost traction motors [IE Agency, Energy Technology Perspectives (2017)]. Since the rare earth permanent magnet (REPM) market is essentially 100% net import reliant in the United States and has proven to have an unstable cost and supply structure in recent years, a replacement RE-free PM material must be designed or selected, fully developed, and implemented. Alnico, with its high saturation magnetization and excellent thermal stability, appears to be uniquely suited for this task. Further, while alnico typically has been considered a relatively low coercivity hard magnet, strides have been made to increase the coercivity to levels suitable for traction drive motors [W Tang, IEEE Trans. Magn., 51 (2015)]. If a simple non-cast approach for achieving near [001] easy axis grain aligned permanent magnets can be found, this would allow mass-produced final-shape anisotropic high energy product magnets suitable for usage in compact high RPM rotor designs. Therefore, a powder metallurgical approach is being explored that uses classic compression molding with "de-bind and sinter" methods, where a novel applied uniaxial loading, and an applied magnetic field may create final-shape magnets with highly textured resulting microstructures by two different mechanisms. Results indicate a positive correlation between applied uniaxial load and resulting texture (Fig. 1), along with benefits from using an applied magnetic field for improved texture, as well. The apparent mechanisms and resulting properties will be described using closed loop hysteresisgraph measurements, EBSD orientation mapping, and high

  19. Agent-based modeling of sustainable behaviors

    CERN Document Server

    Sánchez-Maroño, Noelia; Fontenla-Romero, Oscar; Polhill, J; Craig, Tony; Bajo, Javier; Corchado, Juan

    2017-01-01

    Using the O.D.D. (Overview, Design concepts, Detail) protocol, this title explores the role of agent-based modeling in predicting the feasibility of various approaches to sustainability. The chapters incorporated in this volume consist of real case studies to illustrate the utility of agent-based modeling and complexity theory in discovering a path to more efficient and sustainable lifestyles. The topics covered within include: households' attitudes toward recycling, designing decision trees for representing sustainable behaviors, negotiation-based parking allocation, auction-based traffic signal control, and others. This selection of papers will be of interest to social scientists who wish to learn more about agent-based modeling as well as experts in the field of agent-based modeling.

  20. Recommendation advertising method based on behavior retargeting

    Science.gov (United States)

    Zhao, Yao; YIN, Xin-Chun; CHEN, Zhi-Min

    2011-10-01

    Online advertising has become an important business in e-commerce. Ad recommended algorithms are the most critical part in recommendation systems. We propose a recommendation advertising method based on behavior retargeting which can avoid leakage click of advertising due to objective reasons and can observe the changes of the user's interest in time. Experiments show that our new method can have a significant effect and can be further to apply to online system.

  1. Research on software behavior trust based on hierarchy evaluation

    Science.gov (United States)

    Long, Ke; Xu, Haishui

    2017-08-01

    In view of the correlation software behavior, we evaluate software behavior credibility from two levels of control flow and data flow. In control flow level, method of the software behavior of trace based on support vector machine (SVM) is proposed. In data flow level, behavioral evidence evaluation based on fuzzy decision analysis method is put forward.

  2. Behavior-Based Assists for Telerobotic Manipulation

    International Nuclear Information System (INIS)

    Noakes, Mark W.; Hamel, Dr. William R.

    2008-01-01

    Teleoperated manipulation has been a critical tool in hazardous operations where the presence of humans has been precluded since the early days of nuclear material handling. Performance levels and limitations were understood and accepted. However, in the current era of decontamination and decommissioning (D and D) of facilities owned by the U.S. Department of Energy, there has been criticism that traditional remote systems are too expensive, too slow, and too difficult to use by cost-driven demolition companies. Previous research in telerobotics has attempted to alleviate some of these issues; however, it has been difficult to get capabilities generated in the research lab into the field. One major difficulty is the severely unstructured environments found in real D and D type environments. Behavior-based robotics (BBR) is based on concepts specifically designed to permit autonomous robots to function in unstructured environments. BBR schemes use sensor data to interact with the world directly rather than to generate models that are manipulated. Because the robot is immersed in its environment and since sensors are mounted on the robot, sensing and motion are inherently calibrated with respect to the robot. This paper presents a behavior-based approach and architecture for executing telerobotic D and D type tooling tasks

  3. The permanent process

    DEFF Research Database (Denmark)

    Møller, Jesper; McCullagh, Peter

    We extend the boson process first to a large class of Cox processes and second an even larger class of infinitely divisible point processes. Density and moment results are studied in detail. These results are obtained in closed form as weighted permanents, so the extension is called a permanent...... process. Temporal extensions and a particularly tractable case of the permanent process are also studied. Extensions of the ferminon process along similar lines, leading to so-called determinant processes, are discussed at the end. While the permanent process is attractive, the determinant process...

  4. A novel safety device with metal counter meshing gears discriminator directly driven by axial flux permanent magnet micromotors based on MEMS technology

    Science.gov (United States)

    Zhang, Weiping; Chen, Wenyuan; Zhao, Xiaolin; Li, Shengyong; Jiang, Yong

    2005-08-01

    In a novel safety device based on MEMS technology for high consequence systems, the discriminator consists of two groups of metal counter meshing gears and two pawl/ratchet wheel mechanisms. Each group of counter meshing gears is onepiece and driven directly by an axial flux permanent magnet micromotor respectively. The energy-coupling element is an optical shutter with two collimators and a coupler wheel. The safety device's probability is less than 1/106. It is fabricated by combination of an LiGA-like process and precision mechanical engineering. The device has simple structure, few dynamic problems, high strength and strong reliability.

  5. Very low speed performance of active flux based sensorless control: interior permanent magnet synchronous motor vector control versus direct torque and flux control

    DEFF Research Database (Denmark)

    Paicu, M. C.; Boldea, I.; Andreescu, G. D.

    2009-01-01

    This study is focused on very low speed performance comparison between two sensorless control systems based on the novel ‘active flux' concept, that is, the current/voltage vector control versus direct torque and flux control (DTFC) for interior permanent magnet synchronous motor (IPMSM) drives...... with space vector modulation (SVM), without signal injection. The active flux, defined as the flux that multiplies iq current in the dq-model torque expression of all ac machines, is easily obtained from the stator-flux vector and has the rotor position orientation. Therefore notable simplification...

  6. Analytical Calculation of D- and Q-axis Inductance for Interior Permanent Magnet Motors Based on Winding Function Theory

    Directory of Open Access Journals (Sweden)

    Peixin Liang

    2016-07-01

    Full Text Available Interior permanent magnet (IPM motors are widely used in electric vehicles (EVs, benefiting from the excellent advantages of a more rational use of energy. For further improvement of energy utilization, this paper presents an analytical method of d- and q-axis inductance calculation for IPM motors with V-shaped rotor in no-load condition. A lumped parameter magnetic circuit model (LPMCM is adopted to investigate the saturation and nonlinearity of the bridge. Taking into account the influence of magnetic field distribution on inductance, the winding function theory (WFT is employed to accurately calculate the armature reaction airgap magnetic field and d- and q-axis inductances. The validity of the analytical technique is verified by the finite element method (FEM.

  7. A display to support knowledge based behavior

    International Nuclear Information System (INIS)

    Lindsay, R.W.

    1990-01-01

    A computerized display has been created for the Experimental Breeder Reactor II (EBR-II) that incorporates information from plant sensors in a thermodynamic model display. The display is designed to provide an operator with an overall view of the plant process as a heat engine. The thermodynamics of the plant are depicted through the use of ionic figures, animated by plant signals, that are related to the major plant components and systems such as the reactor, intermediate heat exchanger, secondary system, evaporators, superheaters, steam system, steam drum, and turbine-generator. This display supports knowledge based reasoning for the operator as well as providing the traditional rule and skill based behavior, and includes side benefits such a inherent signal validation

  8. A display to support knowledge based behavior

    International Nuclear Information System (INIS)

    Lindsay, R.W.

    1990-01-01

    This paper reports on a computerized display that has been created for the Experimental Breeder Reactor II that incorporates information from plant sensors in a thermodynamic model display. The display is designed to provide an operator with an overall view of the plant process as a heat engine. The thermodynamics of the plant are depicted through the use of iconic figures, animated by plant signals, that are related to the major plant components and systems such as the reactor, intermediate heat exchanger, secondary system, evaporators, superheaters, steam system, steam drum, and turbine-generator. This display supports knowledge based reasoning for the operator as well as providing data for the traditional rule and skill based behavior, and includes side benefits such as inherent signal validation

  9. Conceptual design of a permanent ring magnet based helicon plasma source module intended to be used in a large size fusion grade ion source

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, Arun; Sudhir, Dass; Bandyopadhyay, M., E-mail: mainak@iter-india.org; Chakraborty, A.

    2016-02-15

    A conceptual design of a permanent magnet based single driver helicon plasma source module along with its design approach is described in this paper. The module unit is intended to be used in a large size ion source. The conceptual design of the helicon source module has been carried out using a computer code, HELIC. The magnetic field topology for the ring magnet is simulated with another code, BFieldM and the magnetic field values obtained from the calculation are further used as input in HELIC calculation for the conceptual design. The module is conceptualized based on a cylindrical glass vessel to produce plasma of diameter ∼50 mm, height ∼50 mm. The inner diameter of the permanent ring magnets is also of the same dimension with thickness ∼10 mm each, placed slightly above the backplate to maintain the required magnetic field. The simulated results show that for hydrogen gas, expected plasma density can be achieved as high as ∼10{sup 12}–10{sup 13} cm{sup −3} in the proposed helicon source configuration using 1 kW 13.56 MHz RF generator. An experimental setup to characterize a Helicon source module unit, consisting of a cylindrical glass (plasma) chamber along with the vacuum system, RF power supplies, probes and data acquisition system is being installed.

  10. Development and operation of a Pr_{2}Fe_{14}B based cryogenic permanent magnet undulator for a high spatial resolution x-ray beam line

    Directory of Open Access Journals (Sweden)

    C. Benabderrahmane

    2017-03-01

    Full Text Available Short period, high field undulators are used to produce hard x-rays on synchrotron radiation based storage ring facilities of intermediate energy and enable short wavelength free electron laser. Cryogenic permanent magnet undulators take benefit from improved magnetic properties of RE_{2}Fe_{14}B (Rare Earth based magnets at low temperatures for achieving short period, high magnetic field and high coercivity. Using Pr_{2}Fe_{14}B instead of Nd_{2}Fe_{14}B, which is generally employed for undulators, avoids the limitation caused by the spin reorientation transition phenomenon, and simplifies the cooling system by allowing the working temperature of the undulator to be directly at the liquid nitrogen one (77 K. We describe here the development of a full scale (2 m, 18 mm period Pr_{2}Fe_{14}B cryogenic permanent magnet undulator (U18. The design, construction and optimization, as well as magnetic measurements and shimming at low temperature are presented. The commissioning and operation of the undulator with the electron beam and spectrum measurement using the Nanoscopmium beamline at SOLEIL are also reported.

  11. The colostomy impact score: development and validation of a patient reported outcome measure for rectal cancer patients with a permanent colostomy. A population-based study.

    Science.gov (United States)

    Thyø, A; Emmertsen, K J; Pinkney, T D; Christensen, P; Laurberg, S

    2017-01-01

    The aim was to develop and validate a simple scoring system evaluating the impact of colostomy dysfunction on quality of life (QOL) in patients with a permanent stoma after rectal cancer treatment. In this population-based study, 610 patients with a permanent colostomy after previous rectal cancer treatment during the period 2001-2007 completed two questionnaires: (i) the basic stoma questionnaire consisting of 22 items about stoma function with one anchor question addressing the overall stoma impact on QOL and (ii) the European Organization for Research and Treatment of Cancer Quality of Life Questionnaire (EORTC QLQ) C30. Answers from half of the cohort were used to develop the score and subsequently validated on the remaining half. Logistic regression analyses identified and selected items for the score and multivariate analysis established the score value allocated to each item. The colostomy impact score includes seven items with a total range from 0 to 38 points. A score of ≥ 10 indicates major colostomy impact (Major CI). The score has a sensitivity of 85.7% for detecting patients with significant stoma impact on QOL. Using the EORTC QLQ scales, patients with Major CI experienced significant impairment in their QOL compared to the Minor CI group. This new scoring system appears valid for the assessment of the impact on QOL from having a permanent colostomy in a Danish rectal cancer population. It requires validation in non-Danish populations prior to its acceptance as a valuable patient-reported outcome measure for patients internationally. Colorectal Disease © 2016 The Association of Coloproctology of Great Britain and Ireland.

  12. Comparison of Combined X-Ray Radiography and Magnetic Resonance (XMR) Imaging-Versus Computed Tomography-Based Dosimetry for the Evaluation of Permanent Prostate Brachytherapy Implants

    International Nuclear Information System (INIS)

    Acher, Peter; Rhode, Kawal; Morris, Stephen; Gaya, Andrew; Miquel, Marc; Popert, Rick; Tham, Ivan; Nichol, Janette; McLeish, Kate; Deehan, Charles; Dasgupta, Prokar; Beaney, Ronald; Keevil, Stephen F.

    2008-01-01

    Purpose: To present a method for the dosimetric analysis of permanent prostate brachytherapy implants using a combination of stereoscopic X-ray radiography and magnetic resonance (MR) imaging (XMR) in an XMR facility, and to compare the clinical results between XMR- and computed tomography (CT)-based dosimetry. Methods and Materials: Patients who had received nonstranded iodine-125 permanent prostate brachytherapy implants underwent XMR and CT imaging 4 weeks later. Four observers outlined the prostate gland on both sets of images. Dose-volume histograms (DVHs) were derived, and agreement was compared among the observers and between the modalities. Results: A total of 30 patients were evaluated. Inherent XMR registration based on prior calibration and optical tracking required a further automatic seed registration step that revealed a median root mean square registration error of 4.2 mm (range, 1.6-11.4). The observers agreed significantly more closely on prostate base and apex positions as well as outlining contours on the MR images than on those from CT. Coefficients of variation were significantly higher for observed prostate volumes, D90, and V100 parameters on CT-based dosimetry as opposed to XMR. The XMR-based dosimetry showed little agreement with that from CT for all observers, with D90 95% limits of agreement ranges of 65, 118, 79, and 73 Gy for Observers 1, 2, 3, and 4, respectively. Conclusions: The study results showed that XMR-based dosimetry offers an alternative to other imaging modalities and registration methods with the advantages of MR-based prostate delineation and confident three-dimensional reconstruction of the implant. The XMR-derived dose-volume histograms differ from the CT-derived values and demonstrate less interobserver variability

  13. Family farming and areas of permanent preservation: an analysis based on the colonos’ social representations in Botuverá/SC.

    Directory of Open Access Journals (Sweden)

    Cíntia Uller-Gómez

    2009-07-01

    Full Text Available The purpose of this study is to analyse the colonos’ social representations in Botuverá (SC, concerning the use of the margins of the water courses and the meanings of exotic forestry species planting (eucalyptus, above all in their rural establishments. Examining the heart of peasantry values in general and, in particular, the values expressed by the colonos, we found that the margins of water courses are considered as productive areas for the family. On the other hand, the planting of exotic forestry species appears with more intensity in the rural establishments where the above-mentioned peasant values do not greatly influence the decision-making process, as well as in those establishments that do not exclusively depend on the use of the land. We have concluded that the strategies for environmental preservation should take into account the family farmer’s practical needs and symbolic aspects, creating joint alternatives of conservative use, valuing the fact that there was a greater interest in preserving the biodiversity in the establishments where the peasant categories were more evident. Key-words: Family farming; Riparian vegetation; Permanent preservation areas.

  14. Fracture behavior of W based materials

    International Nuclear Information System (INIS)

    Hack, J.E.

    1991-01-01

    This report describes the results of a program to investigate the fracture properties of tungsten based materials. In particular, the role of crack velocity on crack instability was determined in a W-Fe-Ni-Co ''heavy alloy'' and pure polycrystalline tungsten. A considerable effort was expended on the development of an appropriate crack velocity gage for use on these materials. Having succeeded in that, the gage technology was employed to determine the crack velocity response to the applied level of stress intensity factor at the onset of crack instability in pre-cracked specimens. The results were also correlated to the failure mode observed in two material systems of interest. Major results include: (1) unstable crack velocity measurements on metallic specimens which require high spatial resolution require the use of brittle, insulating substrates, as opposed to the ductile, polymer based substrates employed in low spatial resolution measurements; and (2) brittle failure modes, such as cleavage, are characterized by relatively slow unstable crack velocities while evidence of high degrees of deformation are associated with failures which proceed at high unstable crack velocities. This latter behavior is consistent with the predictions of the modeling of Hack et al and may have a significant impact on the interpretation of fractographs in general

  15. Root canal configuration of human permanent mandibular first molars of an indo-dravidian population based in Southern India: An In vitro study

    Directory of Open Access Journals (Sweden)

    J V Karunakaran

    2017-01-01

    Full Text Available Aim: This study aims to analyze root canal configuration of human permanent mandibular first molars of an indo-Dravidian population based in southern India. Materials and Methods: A total of 1147 mandibular first permanent molars were collected, cleansed, and stored. The number of roots was recorded, access preparations made, pattern of orifices recorded after pulpal floor debridement, dye injected into the canals using apical negative pressure and subjected to a clearing technique. They were then analyzed using a stereo microscope and the canal configurations recorded (Vertucci. The number of roots, the pattern of orifices and canal configuration were recorded. Results: The pattern of orifices was triangular (87.9%, rectangular (8.5%, C-shaped (3.0%, and two orifice pattern (0.6%. About 95.6% of teeth had two roots, and 4.4% had three roots. The most common canal system configuration in mesial root was Vertucci type IV (52.3%, followed by type II (35%. Root canal configuration of the distal root revealed type I configuration in 62.7%, followed by types II (14.5% and IV (12.4%. The distolingual root had a type I configuration. Conclusion: Awareness of canal configuration, adequate clinical skills, use of specialized techniques of diagnosis, debridement and obturation will pave the way for successful treatment outcomes.

  16. Root Canal Configuration of Human Permanent Mandibular First Molars of an Indo-Dravidian Population Based in Southern India: An In vitro Study.

    Science.gov (United States)

    Karunakaran, J V; Samuel, Leo Sujith; Rishal, Yousef; Joseph, M Derick; Suresh, K Rahul; Varghese, Sam T

    2017-11-01

    This study aims to analyze root canal configuration of human permanent mandibular first molars of an indo-Dravidian population based in southern India. A total of 1147 mandibular first permanent molars were collected, cleansed, and stored. The number of roots was recorded, access preparations made, pattern of orifices recorded after pulpal floor debridement, dye injected into the canals using apical negative pressure and subjected to a clearing technique. They were then analyzed using a stereo microscope and the canal configurations recorded (Vertucci). The number of roots, the pattern of orifices and canal configuration were recorded. The pattern of orifices was triangular (87.9%), rectangular (8.5%), C-shaped (3.0%), and two orifice pattern (0.6%). About 95.6% of teeth had two roots, and 4.4% had three roots. The most common canal system configuration in mesial root was Vertucci type IV (52.3%), followed by type II (35%). Root canal configuration of the distal root revealed type I configuration in 62.7%, followed by types II (14.5%) and IV (12.4%). The distolingual root had a type I configuration. Awareness of canal configuration, adequate clinical skills, use of specialized techniques of diagnosis, debridement and obturation will pave the way for successful treatment outcomes.

  17. Functional-Based Assessment of Social Behavior: Introduction and Overview.

    Science.gov (United States)

    Lewis, Timothy J.; Sugai, George

    1994-01-01

    This introduction to and overview of a special issue on social behavior assessment within schools discusses the impact of function-based methodologies on assessment and intervention practices in identification and remediation of challenging social behaviors. (JDD)

  18. AIDS, behavior, and culture: understanding evidence-based prevention

    National Research Council Canada - National Science Library

    Green, Edward C; Ruark, Allison Herling

    2011-01-01

    .... Arguing for a behavior-based approach, the authors make the case that the most effective programs are those that encourage fundamental behavioral changes such as faithfulness, avoidance of concurrent...

  19. Environmentally responsible behavior of nature-based tourists: A review

    Directory of Open Access Journals (Sweden)

    Lee, T.H.

    2013-03-01

    Full Text Available This study assesses the conceptualization of environmentally responsible behavior and methods for measuring such behavior based on a review of previous studies. Four major scales for the extent to which an individual’s behavior is responsible behavior are discussed. Various theoretical backgrounds and cultures provide diverse conceptualizations of environmentally responsible behavior. Both general and site-specific environmentally responsible behavior has been identified in the past studies. This study also discusses the precedents of environmentally responsible behavior and with a general overview; it provides insight into improving future research on this subject.

  20. Permanences GAG-EPA

    CERN Document Server

    GAC-EPA

    2015-01-01

    Le GAC organise chaque mois des permanences avec entretiens individuels. La prochaine permanence se tiendra le : Mardi 5 mai de 13 h 30 à 16 h 00 Salle de réunion de l’Association du personnel Les permanences suivantes auront lieu les mardis 2 juin, 1er septembre, 6 octobre, 3 novembre et 1er décembre 2015. Les permanences du Groupement des Anciens sont ouvertes aux bénéficiaires de la Caisse de pensions (y compris les conjoints survivants) et à tous ceux qui approchent de la retraite. Nous invitons vivement ces derniers à s’associer à notre groupement en se procurant, auprès de l’Association du personnel, les documents nécessaires.

  1. Permanent quadrupole magnets

    International Nuclear Information System (INIS)

    Bush, E.D. Jr.

    1976-01-01

    A family of quadrupole magnets using a soft iron return yoke and circular cross-section permanent magnet poles were fabricated to investigate the feasibility for use in ion or electron beam focusing applications in accelerators and transport lines. Magnetic field measurements yielded promising results. In fixed-field applications, permanent magnets with sufficient gradients would be a low cost substitute for conventional electromagnets, eliminating the need for power supplies, associated wiring, and cooling. (author)

  2. Marxism as permanent revolution

    OpenAIRE

    van Ree, E.

    2013-01-01

    This article argues that the 'permanent revolution' represented the dominant element in Karl Marx and Friedrich Engels' political discourse, and that it tended to overrule considerations encapsulated in 'historical materialism'. In Marx and Engels's understanding, permanent revolution did not represent a historical shortcut under exceptional circumstances, but the course revolutions in the modern era would normally take. Marx and Engels traced back the pattern to the sixteenth century. It is ...

  3. Behavior based safety approach towards fire

    International Nuclear Information System (INIS)

    Suresh Kumar, R.

    2009-01-01

    The behavior of the individual who notice fire first is very important because it affect the safety of all occupants of the area. Human behavior on fire depends on variables of the buildings in which fire occurs and by the appearance of the fire when it is detected. Altruistic behavior of human being will help to handle the critical conditions due to fire emergencies. NPCIL have developed a culture of systematic approach to safeguard men and materials from fire by training and awareness. In our Nuclear Power Plants, we have an effective plan and system to test the plans. In each emergency exercises, the behavior of individuals will be monitored and recorded

  4. Determinants of oral hygiene behavior : a study based on the theory of planned behavior

    NARCIS (Netherlands)

    Buunk-Werkhoven, Y.A.; Dijkstra, Arie; van der Schans, C.P.

    Objective: The aim of this study was to develop an index for oral hygiene behavior (OHB) and to examine potential predictors of this actual behavior based on the theory of planned behavior (TPB). Measures of oral health knowledge (OHK) and the expected effect of having healthy teeth on social

  5. The cycloid Permanent Magnetic Gear

    DEFF Research Database (Denmark)

    Rasmussen, Peter Omand; Andersen, Torben Ole; Jørgensen, Frank T.

    2008-01-01

    This paper presents a new permanent-magnet gear based on the cycloid gearing principle. which normally is characterized by an extreme torque density and a very high gearing ratio. An initial design of the proposed magnetic gear was designed, analyzed, and optimized with an analytical model...... regarding torque density. The results were promising as compared to other high-performance magnetic-gear designs. A test model was constructed to verify the analytical model....

  6. The Study of Fuzzy Proportional Integral Controllers Based on Improved Particle Swarm Optimization for Permanent Magnet Direct Drive Wind Turbine Converters

    Directory of Open Access Journals (Sweden)

    Yancai Xiao

    2016-05-01

    Full Text Available In order to meet the requirements of high precision and fast response of permanent magnet direct drive (PMDD wind turbines, this paper proposes a fuzzy proportional integral (PI controller associated with a new control strategy for wind turbine converters. The purpose of the control strategy is to achieve the global optimization for the quantization factors, ke and kec, and scale factors, kup and kui, of the fuzzy PI controller by an improved particle swarm optimization (PSO method. Thus the advantages of the rapidity of the improved PSO and the robustness of the fuzzy controller can be fully applied in the control process. By conducting simulations for 2 MW PMDD wind turbines with Matlab/Simulink, the performance of the fuzzy PI controller based on the improved PSO is demonstrated to be obviously better than that of the PI controller or the fuzzy PI controller without using the improved PSO under the situation when the wind speed changes suddenly.

  7. Nonlinear chaos control in a permanent magnet reluctance machine

    International Nuclear Information System (INIS)

    Harb, Ahmad M.

    2004-01-01

    The dynamics of a permanent magnet synchronous machine (PMSM) is analyzed. The study shows that under certain conditions the PMSM is experiencing chaotic behavior. To control these unwanted chaotic oscillations, a nonlinear controller based on the backstepping nonlinear control theory is designed. The objective of the designed control is to stabilize the output chaotic trajectory by forcing it to the nearest constant solution in the basin of attraction. The result is compared with a nonlinear sliding mode controller. The designed controller that based on backstepping nonlinear control was able to eliminate the chaotic oscillations. Also the study shows that the designed controller is mush better than the sliding mode control

  8. Permanently calibrated interpolating time counter

    International Nuclear Information System (INIS)

    Jachna, Z; Szplet, R; Kwiatkowski, P; Różyc, K

    2015-01-01

    We propose a new architecture of an integrated time interval counter that provides its permanent calibration in the background. Time interval measurement and the calibration procedure are based on the use of a two-stage interpolation method and parallel processing of measurement and calibration data. The parallel processing is achieved by a doubling of two-stage interpolators in measurement channels of the counter, and by an appropriate extension of control logic. Such modification allows the updating of transfer characteristics of interpolators without the need to break a theoretically infinite measurement session. We describe the principle of permanent calibration, its implementation and influence on the quality of the counter. The precision of the presented counter is kept at a constant level (below 20 ps) despite significant changes in the ambient temperature (from −10 to 60 °C), which can cause a sevenfold decrease in the precision of the counter with a traditional calibration procedure. (paper)

  9. Hot-Tearing Assessment of Multicomponent Nongrain-Refined Al-Cu Alloys for Permanent Mold Castings Based on Load Measurements in a Constrained Mold

    Science.gov (United States)

    Sabau, Adrian S.; Mirmiran, Seyed; Glaspie, Christopher; Li, Shimin; Apelian, Diran; Shyam, Amit; Allen Haynes, J.; Rodriguez, Andres F.

    2018-06-01

    The hot-tearing resistance of multicomponent Al-Cu alloys during permanent mold casting was investigated using a constrained permanent mold in which the load and temperature were measured. The nominal Cu composition was varied from 5 to 8 wt pct. Casting experiments were conducted without adding any grain-refining inoculants. The following variables, which were obtained from the measured load data during casting, were considered to assess the hot-tearing resistance of the Al-Cu multicomponent alloys: "V"-like signature in the load rate variation, load at solidus point, and load rate average over the freezing range. In addition, a hot-tearing criterion based on the variation of the fraction of solid in the late stages of solidification was used. It was found that all criteria considered can accurately predict the alloys with the lowest and highest hot-tear resistance, respectively. It was found that the rate of measured load during casting could be used to indicate substantial hot tearing. However, the load rate variation could not be used to detect when small hot tears were present. Among all the criteria considered, the load at the solidus point shows an excellent agreement with experimentally observed hot-tearing resistance for all but one alloy. The poorly resistant hot-tearing alloys exhibited mainly coarse columnar grains while the most hot-tearing resistant alloys exhibited a much more refined grain microstructure. This is the first study in which good hot-tear resistance is demonstrated for multicomponent Al-Cu alloys with nominal Cu content greater than 7 wt pct.

  10. Updating biological bases of social behavior.

    Science.gov (United States)

    O'Connor, Thomas G

    2014-09-01

    This month's collation of papers deals with social behaviors that operationalize key constructs in fields covered by the journal, including attachment theory and parenting; emotional regulation; psychopathology of several forms; general and specific cognitive abilities. Notably, many examples are offered of how these social behaviors link with biology. That is an obvious and important direction for clinical research insofar as it helps to erase a perceptual chasm and artificial duality between 'behavior' and 'biology'. But, although it must be the case that social behavior has biological connections of one sort or other, identifying reliable connections with practical application has proved to be a non-trivial challenge. In particular, the challenge seems to be in measuring social behavior meaningfully enough that it could be expected to have a biological pulse, and in measuring biological markers systematically enough that emergent-downstream effects would surface. Associations are not especially uncommon, but it has been a frustrating task in constructing a practically broad model from a bricolage of scattered and disconnected parts and findings in the literature. Several reports in this issue offer contrasts that may help move along this line of study. © 2014 Association for Child and Adolescent Mental Health.

  11. Introduction to permanent magnets

    International Nuclear Information System (INIS)

    Zijlstra, H.

    1985-01-01

    Some general considerations concerning the application of permanent magnets are developed. The relevant magnet properties are discussed, with particular reference to Nd-Fe-B alloy. The author comes to the following conclusions; the air gap field B should be high, for high electrical efficiency; the magnet should face the air gap, for efficient use of the magnet material; the magnet material should therefore have a high remanence; and the new Nd-Fe-B magnet fits in nicely, having (potentially) the highest remanence ever reported in permanent magnets, combined with sufficient coercivity to sustain it

  12. Trojan detection model based on network behavior analysis

    International Nuclear Information System (INIS)

    Liu Junrong; Liu Baoxu; Wang Wenjin

    2012-01-01

    Based on the analysis of existing Trojan detection technology, this paper presents a Trojan detection model based on network behavior analysis. First of all, we abstract description of the Trojan network behavior, then according to certain rules to establish the characteristic behavior library, and then use the support vector machine algorithm to determine whether a Trojan invasion. Finally, through the intrusion detection experiments, shows that this model can effectively detect Trojans. (authors)

  13. Effects of Nonverbal Behavior on Perceptions of Power Bases.

    Science.gov (United States)

    Aguinis, Herman; Simonsen, Melissa M.; Pierce, Charles A.

    1998-01-01

    Manipulates three types of nonverbal behaviors and examines their effects on perceptions of power bases. Reports that a relaxed facial expression increased the ratings for five of the selected power bases; furthermore, direct eye contact yielded higher credibility ratings. Provides evidence that various nonverbal behaviors have only additive…

  14. Behavioral Activation Is an Evidence-Based Treatment for Depression

    Science.gov (United States)

    Sturmey, Peter

    2009-01-01

    Recent reviews of evidence-based treatment for depression did not identify behavioral activation as an evidence-based practice. Therefore, this article conducted a systematic review of behavioral activation treatment of depression, which identified three meta-analyses, one recent randomized controlled trial and one recent follow-up of an earlier…

  15. M.I.N.G., Mars Investment for a New Generation: Robotic construction of a permanently manned Mars base

    Science.gov (United States)

    Amos, Jeff; Beeman, Randy; Brown, Susan; Calhoun, John; Hill, John; Howorth, Lark; Mcfaden, Clay; Nguyen, Paul; Reid, Philip; Rexrode, Stuart

    1989-01-01

    A basic procedure for robotically constructing a manned Mars base is outlined. The research procedure was divided into three areas: environment, robotics, and habitat. The base as designed will consist of these components: two power plants, communication facilities, a habitat complex, and a hangar, a garage, recreation and manufacturing facilities. The power plants will be self-contained nuclear fission reactors placed approx. 1 km from the base for safety considerations. The base communication system will use a combination of orbiting satellites and surface relay stations. This system is necessary for robotic contact with Phobos and any future communication requirements. The habitat complex will consist of six self-contained modules: core, biosphere, science, living quarters, galley/storage, and a sick bay which will be brought from Phobos. The complex will be set into an excavated hole and covered with approximately 0.5 m of sandbags to provide radiation protection for the astronauts. The recreation, hangar, garage, and manufacturing facilities will each be transformed from the four one-way landers. The complete complex will be built by autonomous, artificially intelligent robots. Robots incorporated into the design are as follows: Large Modular Construction Robots with detachable arms capable of large scale construction activities; Small Maneuverable Robotic Servicers capable of performing delicate tasks normally requiring a suited astronaut; and a trailer vehicle with modular type attachments to complete specific tasks; and finally, Mobile Autonomous Rechargeable Transporters capable of transferring air and water from the manufacturing facility to the habitat complex.

  16. M.I.N.G., Mars Investment for a New Generation: Robotic construction of a permanently manned Mars base

    Science.gov (United States)

    Amos, Jeff; Beeman, Randy; Brown, Susan; Calhoun, John; Hill, John; Howorth, Lark; McFaden, Clay; Nguyen, Paul; Reid, Philip; Rexrode, Stuart

    1989-05-01

    A basic procedure for robotically constructing a manned Mars base is outlined. The research procedure was divided into three areas: environment, robotics, and habitat. The base as designed will consist of these components: two power plants, communication facilities, a habitat complex, and a hanger, a garage, recreation and manufacturing facilities. The power plants will be self-contained nuclear fission reactors placed approx. 1 km from the base for safety considerations. The base communication system will use a combination of orbiting satellites and surface relay stations. This system is necessary for robotic contact with Phobos and any future communication requirements. The habitat complex will consist of six self-contained modules: core, biosphere, science, living quarters, galley/storage, and a sick bay which will be brought from Phobos. The complex will be set into an excavated hole and covered with approximately 0.5 m of sandbags to provide radiation protection for the astronauts. The recreation, hangar, garage, and manufacturing facilities will each be transformed from the four one-way landers. The complete complex will be built by autonomous, artificially intelligent robots. Robots incorporated into the design are as follows: Large Modular Construction Robots with detachable arms capable of large scale construction activities; Small Maneuverable Robotic Servicers capable of performing delicate tasks normally requiring a suited astronaut; and a trailer vehicle with modular type attachments to complete specific tasks; and finally, Mobile Autonomous Rechargeable Transporters capable of transferring air and water from the manufacturing facility to the habitat complex.

  17. Enhanced robust fractional order proportional-plus-integral controller based on neural network for velocity control of permanent magnet synchronous motor.

    Science.gov (United States)

    Zhang, Bitao; Pi, YouGuo

    2013-07-01

    The traditional integer order proportional-integral-differential (IO-PID) controller is sensitive to the parameter variation or/and external load disturbance of permanent magnet synchronous motor (PMSM). And the fractional order proportional-integral-differential (FO-PID) control scheme based on robustness tuning method is proposed to enhance the robustness. But the robustness focuses on the open-loop gain variation of controlled plant. In this paper, an enhanced robust fractional order proportional-plus-integral (ERFOPI) controller based on neural network is proposed. The control law of the ERFOPI controller is acted on a fractional order implement function (FOIF) of tracking error but not tracking error directly, which, according to theory analysis, can enhance the robust performance of system. Tuning rules and approaches, based on phase margin, crossover frequency specification and robustness rejecting gain variation, are introduced to obtain the parameters of ERFOPI controller. And the neural network algorithm is used to adjust the parameter of FOIF. Simulation and experimental results show that the method proposed in this paper not only achieve favorable tracking performance, but also is robust with regard to external load disturbance and parameter variation. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

  18. Object permanence in lemurs.

    Science.gov (United States)

    Deppe, Anja M; Wright, Patricia C; Szelistowski, William A

    2009-03-01

    Object permanence, the ability to mentally represent objects that have disappeared from view, should be advantageous to animals in their interaction with the natural world. The objective of this study was to examine whether lemurs possess object permanence. Thirteen adult subjects representing four species of diurnal lemur (Eulemur fulvus rufus, Eulemur mongoz, Lemur catta and Hapalemur griseus) were presented with seven standard Piagetian visible and invisible object displacement tests, plus one single visible test where the subject had to wait predetermined times before allowed to search, and two invisible tests where each hiding place was made visually unique. In all visible tests lemurs were able to find an object that had been in clear view before being hidden. However, when lemurs were not allowed to search for up to 25-s, performance declined with increasing time-delay. Subjects did not outperform chance on any invisible displacements regardless of whether hiding places were visually uniform or unique, therefore the upper limit of object permanence observed was Stage 5b. Lemur species in this study eat stationary foods and are not subject to stalking predators, thus Stage 5 object permanence is probably sufficient to solve most problems encountered in the wild.

  19. Permanent Magnet Dipole for DIRAC Design Report

    CERN Document Server

    Vorozhtsov, Alexey

    2012-01-01

    Two dipole magnets including one spare unit are needed for the for the DIRAC experiment. The proposed design is a permanent magnet dipole. The design based on Sm2Co17 blocks assembled together with soft ferromagnetic pole tips. The magnet provides integrated field strength of 24.6 10-3 T×m inside the aperture of 60 mm. This Design Report summarizes the main magnetic and mechanic design parameters of the permanent dipole magnets.

  20. Perspectives for high-performance permanent magnets: applications, coercivity, and new materials

    Science.gov (United States)

    Hirosawa, Satoshi; Nishino, Masamichi; Miyashita, Seiji

    2017-03-01

    High-performance permanent magnets are indispensable in the production of high-efficiency motors and generators and ultimately for sustaining the green earth. The central issue of modern permanent magnetism is to realize high coercivity near and above room temperature on marginally hard magnetic materials without relying upon the critical elements such as heavy rare earths by means of nanostructure engineering. Recent investigations based on advanced nanostructure analysis and large-scale first principles calculations have led to significant paradigm shifts in the understandings of coercivity mechanism in Nd-Fe-B permanent magnets, which includes the discovery of the ferromagnetism of the thin (2 nm) intergranular phase surrounding the Nd2Fe14B grains, the occurrence of negative (in-plane) magnetocrystalline anisotropy of Nd ions and some Fe atoms at the interface which degrades coercivity, and visualization of the stochastic behaviors of magnetization in the magnetization reversal process at high temperatures. A major change may occur also in the motor topologies, which is currently overwhelmed by the magnetic flux weakening interior permanent magnet motor type, to other types with variable flux permanent magnet type in some applications to open up a niche for new permanent magnet materials. Keynote talk at 8th International Workshop on Advanced Materials Science and Nanotechnology (IWAMSN2016), 8-12 November 2016, Ha Long City, Vietnam.

  1. A Steady-State Analysis Method for Modular Multilevel Converters Connected to Permanent Magnet Synchronous Generator-Based Wind Energy Conversion Systems

    Directory of Open Access Journals (Sweden)

    Zhijie Liu

    2018-02-01

    Full Text Available Modular multilevel converters (MMCs have shown great potential in the area of multi-megawatt wind energy conversion system (WECS based on permanent magnet synchronous generators (PMSGs. However, the studies in this area are few, and most of them refer to the MMC used in high-voltage direct current (HVDC systems, and hence the characteristics of the PMSG are not considered. This paper proposes a steady-state analysis method for MMCs connected to a PMSG-based WECS. In the proposed method, only the wind speed (operating condition is required as input, and all the electrical quantities in the MMC, including the amplitudes, phase angles and their harmonics, can be calculated step by step. The analysis method is built on the proposed d-q frame mathematical model. Interactions of electrical quantities between the MMC and PMSG are comprehensively considered. Moreover, a new way to calculate the average switching functions are adopted in order to improve the accuracy of the analysis method. Applications of the proposed method are also presented, which includes the characteristic analysis of capacitor voltage ripples and the capacitor sizing. Finally, the accuracy of the method and the correctness of the analysis are verified by simulations and experiments.

  2. Implementation of a sliding-mode-based position sensorless drive for high-speed micro permanent-magnet synchronous motors.

    Science.gov (United States)

    Chi, Wen-Chun; Cheng, Ming-Yang

    2014-03-01

    Due to issues such as limited space, it is difficult if it is not impossible to employ a position sensor in the drive control of high-speed micro PMSMs. In order to alleviate this problem, this paper analyzes and implements a simple and robust position sensorless field-oriented control method of high-speed micro PMSMs based on the sliding-mode observer. In particular, the angular position and velocity of the rotor of the high-speed micro PMSM are estimated using the sliding-mode observer. This observer is able to accurately estimate rotor position in the low speed region and guarantee fast convergence of the observer in the high speed region. The proposed position sensorless control method is suitable for electric dental handpiece motor drives where a wide speed range operation is essential. The proposed sensorless FOC method is implemented using a cost-effective 16-bit microcontroller and tested in a prototype electric dental handpiece motor. Several experiments are performed to verify the effectiveness of the proposed method. © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

  3. Regenerative endodontics--biologically-based treatment for immature permanent teeth: a case report and review of the literature.

    Science.gov (United States)

    Thomson, A; Kahler, B

    2010-12-01

    A paradigm shift in the treatment of immature, necrotic teeth has occurred with biologically-based principles and regenerative endodontic protocols replacing traditional 'apexification' procedures. Preliminary research suggests that stem and progenitor cells from the pulp and/or periodontium contribute to continued root development when regenerative procedures are followed. A mandibular premolar tooth with a chronic periapical abscess was irrigated with sodium hypochlorite with minimal instrumentation and then dressed with tri-antibiotic paste consisting of ciprofloxacin, metronidazole and amoxicillin. At a subsequent visit a blood clot was evoked in the canal by irritating periapical tissues and the canal sealed with mineral trioxide aggregate, glass ionomer cement and composite resin. Resolution of apical periodontitis and the draining sinus, continued root maturation and apical closure occurred over an 18-month period. The tooth became responsive to pulp sensibility testing. It is important that dentists recognize the potential of regenerative endodontics in the treatment of necrotic, immature teeth. Initial management should involve irrigation with sodium hypochlorite only. Intra-canal medicaments, such as calcium hydroxide, are contraindicated as they inhibit further root growth. This report uses a variation of the tri-antibiotic paste currently recommended for regenerative procedures that avoided the discolouration of the crown associated with current protocols. Regenerative endodontics with continued root growth may reduce the risk of fracture and premature tooth loss associated with traditional 'apexification' procedures where the root remains thin and weak. © 2010 Australian Dental Association.

  4. Nd2Fe14C-based magnet with better permanent magnetic properties prepared by a simple mechanochemical method

    Science.gov (United States)

    Geng, Hongmin; Ji, Yuan; Zhang, Jingjing; Gao, Yuchao; Yan, Yu; Wang, Wenquan; Su, Feng; Du, Xiaobo

    2017-11-01

    Nd2Fe14C-based magnet is prepared by a mechanochemical method, namely high-energy ball-milling Nd2Fe11Bx (x = 0-0.15) alloy in heptane (C7H16), followed by annealing to 850 °C in vacuum. Under the action of high-energy ball-milling, Nd2Fe11Bx react with heptane to form NdH2+δ, Fe-(CB), C, etc. H2 is released and Nd2Fe17, Nd2Fe17Cx (x = 0-3), Nd2Fe14C, Nd carbides and α-Fe are formed in the subsequent annealing. C amount depends on ball-milling time t. Long time ball milling or high C content suppresses the formation of 2:17 phase and favors the formation of 2:14:1 phase in the final products. Excessive ball-milling results in the quick increase of α-Fe. The maximum of magnetically hard Nd2Fe14C is obtained at t = 4 h. For Nd2Fe11 samples, there exists considerable quantity of Nd carbides and α-Fe phase appears earlier and increases rapidly with extending the ball-milling time t. The addition of B element shortens the ball-milling time of the formation of maximum Nd2Fe14C and prominently suppresses the formation of Nd carbide and α-Fe. The optimum magnetic properties, coercivity iHc of 1193.7 kA/m, remanence Mr of 580.9 kA/m, maximum magnetic energy product (BH)max of 91.7 kJ/m3 is approaching to its theoretic value of 99.2 kJ/m3 for isotropic Nd2Fe14C magnet, are obtained in Nd2Fe11B0.06 alloy ball milled for 3.5 h.

  5. The Question of Decalage Between Object Permanence and Person Permanence

    Science.gov (United States)

    And Others; Jackson, Elaine

    1978-01-01

    Presents a study of decalage between object permanence and person permanence. Decalage was influenced by environmental as well as stimulus factors with infants tested between 6- and 81/4-months/of-age. (BD)

  6. Management of REM sleep behavior disorder: An evidence based review

    OpenAIRE

    Preeti Devnani; Racheal Fernandes

    2015-01-01

    Rapid eye movement (REM) sleep behavior disorder (RBD) is characterized by dream enactment behavior resulting from a loss of REM skeletal muscle atonia. The neurobiology of REM sleep and the characteristic features of REM atonia have an important basis for understanding the aggravating etiologies the proposed pharmacological interventions in its management. This review outlines the evidence for behavioral and therapeutic measures along with evidence-based guidelines for their implementation, ...

  7. Effect of Cognitive-Behavioral-Theory-Based Skill Training on Academic Procrastination Behaviors of University Students

    Science.gov (United States)

    Toker, Betül; Avci, Rasit

    2015-01-01

    This study examined the effectiveness of a cognitive-behavioral theory (CBT) psycho-educational group program on the academic procrastination behaviors of university students and the persistence of any training effect. This was a quasi-experimental research based on an experimental and control group pretest, posttest, and followup test model.…

  8. Study of the influence of zirconium and gallium on the magnetic properties and microstructures of praseodymium-based permanent magnets

    International Nuclear Information System (INIS)

    Fusco, Alexandre Giardini

    2006-01-01

    In this work was studied the influence of the addition of 0.5 at. % of zirconium and gallium on praseodymium-based HD sintered magnets obtained using a mixture of alloys. The alloys used in this study were: Pr 12.6 Fe 68.3 Co 11.6 B 6 Zr 0.5 Ga 1 , Pr 16 Fe 75.5 B 8 Zr 0.5 , Pr 13 Fe 80.5 B 6 Zr 0.5 . The investigation started by measuring the magnetic properties and observing the microstructure of the magnets. After that, the magnets were annealed at 1000 deg C for 2 hours followed by rapid cooling, in a total of 10 hours. This heat treatment was followed by 5 hours at the same temperature up to a total of 35 hours. Changes in the microstructure were compared to the change in the magnetic properties aiming at a proper understanding of the role of each added element in relation to the magnetically hard phase (phase Φ). It has been shown that gallium and zirconium act as grain refiners of the matrix phase Φ. Gallium acts in the grain and favoring of the shape stability and improvement of the magnetic properties. For the Pr 14.3 Fe 71.9 Co 5.8 B 7 Zr 0.5 Ga 0.5 sintered magnet the evolution of the magnetic properties after 15 hours heat treatment was: remanence from (1.25±0.02) T to (1.30±0.02) T, intrinsic coercivity from (1.11±0.02) T to (0.87±0.02) T, squareness factor from (0.68±0.02) to (0.82±0.02) and energy product from (285±5) kJ/m 3 to (317±5) kJ/m 3 . Zirconium has two effects on the sintered magnets. Firstly, avoiding random grain growth and enhancing anisotropy. However, by concentrating on the grain boundaries, yield reverse domains and is detrimental to the intrinsic coercivity. For the sintered Pr 14.5 Fe 78 B 7 Zr 0.5 magnet the evolution of the magnetic properties achieved after a heat treatment of 15 hours was: remanence from (1.19±0.02) T to (1.25±0.02) T, coercivity from (0.74±0.02) T to (0.94±0.02) T, squareness factor from (0.88±0.02) to (0,85±0.02) and energy product from (258±5) kJ/m 3 to (291±5) kJ/m 3 . For the Pr 16 Fe 75

  9. Variable Permanent Magnet Quadrupole

    International Nuclear Information System (INIS)

    Mihara, T.; Iwashita, Y.; Kyoto U.; Kumada, M.; NIRS, Chiba; Spencer, C.M.; SLAC

    2007-01-01

    A permanent magnet quadrupole (PMQ) is one of the candidates for the final focus lens in a linear collider. An over 120 T/m strong variable permanent magnet quadrupole is achieved by the introduction of saturated iron and a 'double ring structure'. A fabricated PMQ achieved 24 T integrated gradient with 20 mm bore diameter, 100 mm magnet diameter and 20 cm pole length. The strength of the PMQ is adjustable in 1.4 T steps, due to its 'double ring structure': the PMQ is split into two nested rings; the outer ring is sliced along the beam line into four parts and is rotated to change the strength. This paper describes the variable PMQ from fabrication to recent adjustments

  10. Static devices with new permanent magnets

    International Nuclear Information System (INIS)

    Chavanne, J.; Laforest, J.; Pauthenet, R.

    1987-01-01

    The high remanence and coercivity of the new permanent magnet materials are of special interest in the static applications. High ordering temperature and are uniaxial anisotropy at the origin of their good permanent magnet properties are obtained in rare earth-transition metal compounds. Binary SmCo/sub 5/ and Sm/sub 2/Co/sub 17/ and ternary Nd/sub 2/Fe/sub 14/B compounds are the basis materials of the best permanent magnets. new concepts of calculations of static devices with these magnets can be applied: the magnetization can be considered as ridig, the density of the surface Amperian current is constant, the relative permeability is approximately 1 and the induction calculations are linear. Examples of hexapoles with Sm-Co and NdFeB magnets are described and the performances are compared. The problems of temperature behavior and corrosion resistance are underlined

  11. Modeling, analysis and comparison of TSR and OTC methods for MPPT and power smoothing in permanent magnet synchronous generator-based wind turbines

    International Nuclear Information System (INIS)

    Nasiri, M.; Milimonfared, J.; Fathi, S.H.

    2014-01-01

    Highlights: • Small signal modeling of PMSG wind turbine with two controllers are introduced. • Poles and zeroes analyzing of OTC and TSR methods is performed. • Generator output power with varying wind speed in PMSG wind turbine is studied. • MPPT capability of OTC and TSR methods to wind speed variations are compared. • Power smoothing capability and reducing mechanical stress of both methods are studied. - Abstract: This paper presents a small signal modeling of a direct-driven permanent magnet synchronous generator (PMSG) based on wind turbine which is connected to the grid via back-to-back converters. The proposed small signal model includes two maximum power point tracking (MPPT) controllers: tip speed ratio (TSR) control and optimal torque control (OTC). These methods are analytically compared to illustrate MPPT and power smoothing capability. Then, to compare the MPPT and power smoothing operation of the mentioned methods, simulations are performed in MATLAB/Simulink software. From the simulation results, OTC is highly efficient in power smoothing enhancement and has clearly good performance to extract maximum power from wind; however, TSR control has definitely fast responses to wind speed variations with the expense of higher fluctuations due to its non-minimum phase characteristic

  12. Instantaneous power control of a high speed permanent magnet synchronous generator based on a sliding mode observer and a phase locked loop

    Science.gov (United States)

    Duan, Jiandong; Fan, Shaogui; Wu, Fengjiang; Sun, Li; Wang, Guanglin

    2018-06-01

    This paper proposes an instantaneous power control method for high speed permanent magnet synchronous generators (PMSG), to realize the decoupled control of active power and reactive power, through vector control based on a sliding mode observer (SMO), and a phase locked loop (PLL). Consequently, the high speed PMSG has a high internal power factor, to ensure efficient operation. Vector control and accurate estimation of the instantaneous power require an accurate estimate of the rotor position. The SMO is able to estimate the back electromotive force (EMF). The rotor position and speed can be obtained using a combination of the PLL technique and the phase compensation method. This method has the advantages of robust operation, and being resistant to noise when estimating the position of the rotor. Using instantaneous power theory, the relationship between the output active power, reactive power, and stator current of the PMSG is deduced, and the power constraint condition is analysed for operation at the unit internal power factor. Finally, the accuracy of the rotor position detection, the instantaneous power detection, and the control methods are verified using simulations and experiments.

  13. Maximum Power Point Tracking in Variable Speed Wind Turbine Based on Permanent Magnet Synchronous Generator Using Maximum Torque Sliding Mode Control Strategy

    Institute of Scientific and Technical Information of China (English)

    Esmaeil Ghaderi; Hossein Tohidi; Behnam Khosrozadeh

    2017-01-01

    The present study was carried out in order to track the maximum power point in a variable speed turbine by minimizing electromechanical torque changes using a sliding mode control strategy.In this strategy,fhst,the rotor speed is set at an optimal point for different wind speeds.As a result of which,the tip speed ratio reaches an optimal point,mechanical power coefficient is maximized,and wind turbine produces its maximum power and mechanical torque.Then,the maximum mechanical torque is tracked using electromechanical torque.In this technique,tracking error integral of maximum mechanical torque,the error,and the derivative of error are used as state variables.During changes in wind speed,sliding mode control is designed to absorb the maximum energy from the wind and minimize the response time of maximum power point tracking (MPPT).In this method,the actual control input signal is formed from a second order integral operation of the original sliding mode control input signal.The result of the second order integral in this model includes control signal integrity,full chattering attenuation,and prevention from large fluctuations in the power generator output.The simulation results,calculated by using MATLAB/m-file software,have shown the effectiveness of the proposed control strategy for wind energy systems based on the permanent magnet synchronous generator (PMSG).

  14. A Novel Method to Magnetic Flux Linkage Optimization of Direct-Driven Surface-Mounted Permanent Magnet Synchronous Generator Based on Nonlinear Dynamic Analysis

    Directory of Open Access Journals (Sweden)

    Qian Xie

    2016-07-01

    Full Text Available This paper pays attention to magnetic flux linkage optimization of a direct-driven surface-mounted permanent magnet synchronous generator (D-SPMSG. A new compact representation of the D-SPMSG nonlinear dynamic differential equations to reduce system parameters is established. Furthermore, the nonlinear dynamic characteristics of new D-SPMSG equations in the process of varying magnetic flux linkage are considered, which are illustrated by Lyapunov exponent spectrums, phase orbits, Poincaré maps, time waveforms and bifurcation diagrams, and the magnetic flux linkage stable region of D-SPMSG is acquired concurrently. Based on the above modeling and analyses, a novel method of magnetic flux linkage optimization is presented. In addition, a 2 MW D-SPMSG 2D/3D model is designed by ANSYS software according to the practical design requirements. Finally, five cases of D-SPMSG models with different magnetic flux linkages are simulated by using the finite element analysis (FEA method. The nephograms of magnetic flux density are agreement with theoretical analysis, which both confirm the correctness and effectiveness of the proposed approach.

  15. Lawful Permanent Residents - Annual Report

    Data.gov (United States)

    Department of Homeland Security — A lawful permanent resident (LPR) or 'green card' recipient is defined by immigration law as a person who has been granted lawful permanent residence in the United...

  16. [Permanent education in health: a review].

    Science.gov (United States)

    Miccas, Fernanda Luppino; Batista, Sylvia Helena Souza da Silva

    2014-02-01

    To undertake a meta-synthesis of the literature on the main concepts and practices related to permanent education in health. A bibliographical search was conducted for original articles in the PubMed, Web of Science, LILACS, IBECS and SciELO databases, using the following search terms: "public health professional education", "permanent education", "continuing education", "permanent education health". Of the 590 articles identified, after applying inclusion and exclusion criteria, 48 were selected for further analysis, grouped according to the criteria of key elements, and then underwent meta-synthesis. The 48 original publications were classified according to four thematic units of key elements: 1) concepts, 2) strategies and difficulties, 3) public policies and 4) educational institutions. Three main conceptions of permanent education in health were found: problem-focused and team work, directly related to continuing education and education that takes place throughout life. The main strategies for executing permanent education in health are discussion, maintaining an open space for permanent education , and permanent education clusters. The most limiting factor is mainly related to directly or indirect management. Another highlight is the requirement for implementation and maintenance of public policies, and the availability of financial and human resources. The educational institutions need to combine education and service aiming to form critical-reflexive graduates. The coordination between health and education is based as much on the actions of health services as on management and educational institutions. Thus, it becomes a challenge to implement the teaching-learning processes that are supported by critical-reflexive actions. It is necessary to carry out proposals for permanent education in health involving the participation of health professionals, teachers and educational institutions. To undertake a meta-synthesis of the literature on the main concepts and

  17. Individual-Based Compulsive Sexual Behavior Scale: Its Development and Importance in Examining Compulsive Sexual Behavior.

    Science.gov (United States)

    Efrati, Yaniv; Mikulincer, Mario

    2018-04-03

    Compulsive sexual behavior comprises individual-based (e.g., sexual fantasies, compulsive sexual thoughts, masturbation) and partnered (e.g., interpersonal sexual conquests, repeated infidelity) facets. Most instruments for assessing compulsive sexual behavior, however, focus less on the individual-based facet and specifically on fantasies and compulsive thoughts. In the current research, we developed and validated an individual-based compulsive sexual behavior scale (I-CSB). In Study 1 (N = 492), the factorial structure of the I-CSB was examined. In Study 2 (N = 406), we assessed I-CSB's convergent validity. In Study 3 (N = 112), we examined whether the I-CSB differentiates between individuals who suffer from compulsive sexual behavior and those who do not. Results revealed a four-factor structure for individual-based compulsive sexual behavior that is associated with an intense inner conflict regarding sexuality (high arousal contrasting with high sexual anxiety), and that accounts for approximately 75% of the differences between people with compulsive sexual behavior and controls. Results are discussed in light of the need for a broader understanding of compulsive sexual behavior.

  18. Workplace bullying a risk for permanent employees.

    Science.gov (United States)

    Keuskamp, Dominic; Ziersch, Anna M; Baum, Fran E; Lamontagne, Anthony D

    2012-04-01

    We tested the hypothesis that the risk of experiencing workplace bullying was greater for those employed on casual contracts compared to permanent or ongoing employees. A cross-sectional population-based telephone survey was conducted in South Australia in 2009. Employment arrangements were classified by self-report into four categories: permanent, casual, fixed-term and self-employed. Self-report of workplace bullying was modelled using multiple logistic regression in relation to employment arrangement, controlling for sex, age, working hours, years in job, occupational skill level, marital status and a proxy for socioeconomic status. Workplace bullying was reported by 174 respondents (15.2%). Risk of workplace bullying was higher for being in a professional occupation, having a university education and being separated, divorced or widowed, but did not vary significantly by sex, age or job tenure. In adjusted multivariate logistic regression models, casual workers were significantly less likely than workers on permanent or fixed-term contracts to report bullying. Those separated, divorced or widowed had higher odds of reporting bullying than married, de facto or never-married workers. Contrary to expectation, workplace bullying was more often reported by permanent than casual employees. It may represent an exposure pathway not previously linked with the more idealised permanent employment arrangement. A finer understanding of psycho-social hazards across all employment arrangements is needed, with equal attention to the hazards associated with permanent as well as casual employment. © 2012 The Authors. ANZJPH © 2012 Public Health Association of Australia.

  19. Augmenting effectiveness of control loops of a PMSG (permanent magnet synchronous generator) based wind energy conversion system by a virtually adaptive PI (proportional integral) controller

    International Nuclear Information System (INIS)

    Alizadeh, Mojtaba; Kojori, Shokrollah Shokri

    2015-01-01

    Offering substantial features, PMSG (permanent magnet synchronous generator) based WECS (wind energy conversion system) is definitely one of the most reliable and efficient ways of extracting electrical power from the wind. Like other WECSs, PMSG-based WECS (PMSG WECS) encompasses two main control loops, each equipped with PI (proportional integral) controller, to control speed and currents of the system. This work develops a virtually adaptive PI controller to enhance the performance of both main control loops of a PMSG WECS. A WNN (wavelet neural network) is proposed to be added to each closed control loop in series with PI controller. Due to having a cascade connection, the transfer function of the WNN, which is a pure gain in each time step, is multiplied by PI gains. Therefore, the value of transfer function of the WNN, and consequently, both parameters of PI controller can be changed in each time step by online training of the WNN, resulting in a virtually adaptive PI controller. The performance of the proposed controller in improving efficacy of both current and speed control loops is evaluated by simulation studies and is also compared to that of PI controller, WNNC (wavelet neural network controller), and QNNC (quantum neural network controller). - Highlights: • To propose a virtually adaptive PI controller to be used in a PMSG WECS. • Both parameters of PI controller can be changed in each time step. • The proposed controller can be used as both current or speed controller. • The plant data is not required for offline training of proposed current controller.

  20. Effects of Selected Object Characteristics on Object Permanence Test Performance.

    Science.gov (United States)

    Lingle, Kathleen M.; Lingle, John H.

    A study was conducted to investigate the degree to which both object familiarity and motivational factors influence infants' search behavior in an object permanence test. Infants' search behavior for an unfamiliar test object was compared with search behavior for (a) an experientially familiar object that each infant had played with daily for a…

  1. Model and Behavior-Based Robotic Goalkeeper

    DEFF Research Database (Denmark)

    Lausen, H.; Nielsen, J.; Nielsen, M.

    2003-01-01

    This paper describes the design, implementation and test of a goalkeeper robot for the Middle-Size League of RoboCub. The goalkeeper task is implemented by a set of primitive tasks and behaviours coordinated by a 2-level hierarchical state machine. The primitive tasks concerning complex motion...... control are implemented by a non-linear control algorithm, adapted to the different task goals (e.g., follow the ball or the robot posture from local features extracted from images acquired by a catadioptric omni-directional vision system. Most robot parameters were designed based on simulations carried...

  2. Mining Behavior Based Safety Data to Predict Safety Performance

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey C. Joe

    2010-06-01

    The Idaho National Laboratory (INL) operates a behavior based safety program called Safety Observations Achieve Results (SOAR). This peer-to-peer observation program encourages employees to perform in-field observations of each other's work practices and habits (i.e., behaviors). The underlying premise of conducting these observations is that more serious accidents are prevented from occurring because lower level “at risk” behaviors are identified and corrected before they can propagate into culturally accepted “unsafe” behaviors that result in injuries or fatalities. Although the approach increases employee involvement in safety, the premise of the program has not been subject to sufficient empirical evaluation. The INL now has a significant amount of SOAR data on these lower level “at risk” behaviors. This paper describes the use of data mining techniques to analyze these data to determine whether they can predict if and when a more serious accident will occur.

  3. Ontology and modeling patterns for state-based behavior representation

    Science.gov (United States)

    Castet, Jean-Francois; Rozek, Matthew L.; Ingham, Michel D.; Rouquette, Nicolas F.; Chung, Seung H.; Kerzhner, Aleksandr A.; Donahue, Kenneth M.; Jenkins, J. Steven; Wagner, David A.; Dvorak, Daniel L.; hide

    2015-01-01

    This paper provides an approach to capture state-based behavior of elements, that is, the specification of their state evolution in time, and the interactions amongst them. Elements can be components (e.g., sensors, actuators) or environments, and are characterized by state variables that vary with time. The behaviors of these elements, as well as interactions among them are represented through constraints on state variables. This paper discusses the concepts and relationships introduced in this behavior ontology, and the modeling patterns associated with it. Two example cases are provided to illustrate their usage, as well as to demonstrate the flexibility and scalability of the behavior ontology: a simple flashlight electrical model and a more complex spacecraft model involving instruments, power and data behaviors. Finally, an implementation in a SysML profile is provided.

  4. New permanent magnets

    Science.gov (United States)

    Müller, K.-H.; Krabbes, G.; Fink, J.; Gruß, S.; Kirchner, A.; Fuchs, G.; Schultz, L.

    2001-05-01

    Permanent magnets play an important role and are widely spread in daily-life applications. Due to their very low costs, large availability of the row materials and their high chemical stability, hard ferrites are still dominant in the permanent magnet market although their relatively poor magnetic properties are a distinct disadvantage. Today's high-performance magnets are mostly made from Nd 2Fe 14B. The aim of research is to combine the large spontaneous magnetization of 3d metals with strong anisotropy fields known from rare-earth transition-metal compounds and, at the same time, to maintain a high value of the Curie temperature. However, the number of iron-rich rare-earth intermetallics is very limited and, consequently, not much success can be noted in this field for the last 10 years. One alternative concept is to use magnetic fields trapped in type II superconductors where much higher fields can be achieved compared to conventional rare-earth magnets. Very recently, we obtained a trapped field as high as 14.4 T in a melt-textured YBCO bulk sample of a few centimeters in diameter. This is the highest value ever achieved in a bulk superconductor. The trapped field of a superconductor is not governed by the Laplace equation and, therefore, levitation works without any additional (active) stabilization. The disadvantage of these magnets is their low working temperature (of liquid nitrogen and below).

  5. Cryogenic Permanent Magnet Undulators

    International Nuclear Information System (INIS)

    Chavanne, J.; Lebec, G.; Penel, C.; Revol, F.; Kitegi, C.

    2010-01-01

    For an in-vacuum undulator operated at small gaps the permanent magnet material needs to be highly resistant to possible electron beam exposure. At room temperature, one generally uses Sm 2 Co 17 or high coercivity NdFeB magnets at the expense of a limited field performance. In a cryogenic permanent magnet undulator (CPMU), at a temperature of around 150 K, any NdFeB grade reveals a coercivity large enough to be radiation resistant. In particular, very high remanence NdFeB material can be used to build undulators with enhanced field and X-ray brilliance at high photon energy provided that the pre-baking of the undulator above 100 deg. C can be eliminated. The ESRF has developed a full scale 2 m long CPMU with a period of 18 mm. This prototype has been in operation on the ID6 test beamline since January 2008. A significant effort was put into the characterization of NdFeB material at low temperature, the development of dedicated magnetic measurement systems and cooling methods. The measured heat budget with beam is found to be larger than expected without compromising the smooth operation of the device. Leading on from this first experience, new CPMUs are currently being considered for the upgrade of the ESRF.

  6. Autistic children and the object permanence task.

    Science.gov (United States)

    Adrien, J L; Tanguay, P; Barthélémy, C; Martineaú, J; Perrot, A; Hameury, L; Sauvage, D

    1993-01-01

    Many mentally retarded autistic children can understand the concept of object permanence, but, in comparison to developmental-age matched normal children, the behavioral strategies they employ in carrying out the Casati-Lezine Object Permanence Test are deficient and lead to failure. These deficiencies appear unrelated to interference of stereotypic or other bizarre behavior in task performance. Similar problem-solving deficiencies can be found in mentally retarded children who are not autistic, suggesting that the deficiencies themselves are less related to the social-communication deficits of autistic children, but more to the general problem-solving difficulties found in children with a lower developmental quotient. Nevertheless, the qualitative analysis of results shows a tendency in autistic children, despite their better developmental level, to use less coordinated and regular sequences to solve the task than normal or mentally retarded children.

  7. A prototype of behavior selection mechanism based on emotion

    Science.gov (United States)

    Zhang, Guofeng; Li, Zushu

    2007-12-01

    In bionic methodology rather than in design methodology more familiar with, summarizing the psychological researches of emotion, we propose the biologic mechanism of emotion, emotion selection role in creature evolution and a anima framework including emotion similar to the classical control structure; and consulting Prospect Theory, build an Emotion Characteristic Functions(ECF) that computer emotion; two more emotion theories are added to them that higher emotion is preferred and middle emotion makes brain run more efficiently, emotional behavior mechanism comes into being. A simulation of proposed mechanism are designed and carried out on Alife Swarm software platform. In this simulation, a virtual grassland ecosystem is achieved where there are two kinds of artificial animals: herbivore and preyer. These artificial animals execute four types of behavior: wandering, escaping, finding food, finding sex partner in their lives. According the theories of animal ethnology, escaping from preyer is prior to other behaviors for its existence, finding food is secondly important behavior, rating is third one and wandering is last behavior. In keeping this behavior order, based on our behavior characteristic function theory, the specific functions of emotion computing are built of artificial autonomous animals. The result of simulation confirms the behavior selection mechanism.

  8. Advance and permanent public information

    International Nuclear Information System (INIS)

    d'Oleon, C.

    1990-01-01

    The accident at CHERNOBYL highlighted one of the major problems facing the nuclear industry at present and during the years to come: the need to provide information. There are two aspects to this requirement: information at a time of crisis issued when an accident such as that at CHERNOBYL takes place, but which has to be based on a procedure set up before the crisis, and advance and permanent information which prepares the ground for information at a time of crisis. The requirement for information is of particular importance in France, given the preponderance of nuclear energy in the electricity generating industry. The procedure covers the principles which were forcefully asserted by the French public authorities during the CHERNOBYL crisis, the resources strengthened or established at that time, and finally, the introduction of a policy of wider-ranging communication which is based on the idea that one can never compromise with safety

  9. Direct behavior rating as a school-based behavior screener for elementary and middle grades.

    Science.gov (United States)

    Chafouleas, Sandra M; Kilgus, Stephen P; Jaffery, Rose; Riley-Tillman, T Chris; Welsh, Megan; Christ, Theodore J

    2013-06-01

    The purpose of this study was to investigate how Direct Behavior Rating Single Item Scales (DBR-SIS) involving targets of academically engaged, disruptive, and respectful behaviors function in school-based screening assessment. Participants included 831 students in kindergarten through eighth grades who attended schools in the northeastern United States. Teachers provided behavior ratings for a sample of students in their classrooms on the DBR-SIS, the Behavioral and Emotional Screening System (Kamphaus & Reynolds, 2007), and the Student Risk Screening Scale (Drummond, 1994). Given variations in rating procedures to accommodate scheduling differences across grades, analysis was conducted separately for elementary school and middle school grade levels. Results suggested that the recommended cut scores, the combination of behavior targets, and the resulting conditional probability indices varied depending on grade level grouping (lower elementary, upper elementary, middle). For example, for the lower elementary grade level grouping, a combination of disruptive behavior (cut score=2) and academically engaged behavior (cut score=8) was considered to offer the best balance among indices of diagnostic accuracy, whereas a cut score of 1 for disruptive behavior and 8 for academically engaged behavior were recommended for the upper elementary school grade level grouping and cut scores of 1 and 9, respectively, were suggested for middle school grade level grouping. Generally, DBR-SIS cut scores considered optimal for screening using single or combined targets including academically engaged behavior and disruptive behavior by offering a reasonable balance of indices for sensitivity (.51-.90), specificity (.47-.83), negative predictive power (.94-.98), and positive predictive power (.14-.41). The single target of respectful behavior performed poorly across all grade level groups, and performance of DBR-SIS targets was relatively better in the elementary school than middle

  10. The effect of community-acquired bacteraemia on return to workforce, risk of sick leave, permanent disability pension and death: a Danish population-based cohort study.

    Science.gov (United States)

    Dalager-Pedersen, Michael; Koch, Kristoffer; Thomsen, Reimar Wernich; Schønheyder, Henrik Carl; Nielsen, Henrik

    2014-01-29

    Little is known about the prognosis of community-acquired bacteraemia (CAB) in workforce adults. We assessed return to workforce, risk for sick leave, disability pension and mortality within 1 year after CAB in workforce adults compared with blood culture-negative controls and population controls. Population-based cohort study. North Denmark, 1996-2011. We used population-based healthcare registries to identify all patients aged 20-58 years who had first-time blood cultures obtained within 48 h of medical hospital admission, and who were part of the workforce (450 bacteraemia exposed patients and 6936 culture-negative control patients). For each bacteraemia patient, we included up to 10 matched population controls. Return to workforce, risk of sick leave, permanent disability pension and mortality within 1 year after bacteraemia. Regression analyses were used to compute adjusted relative risks (RRs) with 95% CIs. One year after admission, 78% of patients with CAB, 85.7% of culture-negative controls and 96.8% of population controls were alive and in the workforce, and free from sick leave or disability pension. Compared with culture-negative controls, bacteraemia was associated with an increased risk for long-term sick leave (4-week duration, 40.2% vs 23.9%, adjusted RR, 1.51; CI 1.34 to 1.70) and an increased risk for mortality (30-day mortality, 4% vs 1.4%, adjusted RR, 2.34, CI 1.22 to 4.50; 1-year mortality, 8% vs 3.9%, adjusted RR, 1.73; CI 1.18 to 2.55). Bacteraemia patients had a risk for disability pension similar to culture-negative controls (2.7% vs 2.6%, adjusted RR, 0.99, CI 0.48 to 2.02) but greater than population controls (adjusted RR, 5.20; 95% CI 2.16 to 12.50). CAB is associated with long duration of sick leave and considerable mortality in working-age adults when compared with blood culture-negative controls, and an increased 1-year risk for disability pension when compared with population controls.

  11. How Traumatic Violence Permanently Changes Shopping Behavior.

    Science.gov (United States)

    Sigirci, Ozge; Rockmore, Marc; Wansink, Brian

    2016-01-01

    Traumatic experiences - such as combat, living in a conflict country or war-torn nation, or experiencing a violent crime or natural disaster - change social relationships and may also influence a life-time of consumer relationships with brands and shopping. Our focus on this previously overlooked area is centered on an analysis of the long-term shopping habits of 355 combat veterans. We show that those who experienced heavy trauma (e.g., heavy combat) exhibited similar disconnection from brands as others have experienced in social relationships. They became more transactional in that they were more open to switching brands, to trying new products, and buying the least expensive alternative (p buying brands even when they cost more (p < 0.00). Trauma, such as combat, may change one's decision horizon. Functionality and price become more important, which is consistent with the idea that they are more focused on the present moment than on building on the past or saving for the future.

  12. How Traumatic Violence Permanently Changes Shopping Behavior

    Directory of Open Access Journals (Sweden)

    Ozge Sigirci

    2016-09-01

    Full Text Available Traumatic experiences – such as combat, living in a conflict country or war-torn nation, or experiencing a violent crime or natural disaster – change social relationships and may also influence a life-time of consumer relationships with brands and shopping. Our focus on this previously overlooked area is centered on an analysis of the long-term shopping habits of 355 combat veterans. We show that those who experienced heavy trauma (e.g., heavy combat exhibited similar disconnection from brands as others have experienced in social relationships. They became more transactional in that they were more open to switching brands, to trying new products, and buying the least expensive alternative (p < 0.01. In contrast, those who had experienced a light trauma were more influenced by ads and more open to buying brands even when they cost more (p < 0.00. Trauma, such as combat, may change one’s decision horizon. Functionality and price become more important, which is consistent with the idea that they are more focused on the present moment than on building on the past or saving for the future.

  13. Behavioral Modeling Based on Probabilistic Finite Automata: An Empirical Study.

    Science.gov (United States)

    Tîrnăucă, Cristina; Montaña, José L; Ontañón, Santiago; González, Avelino J; Pardo, Luis M

    2016-06-24

    Imagine an agent that performs tasks according to different strategies. The goal of Behavioral Recognition (BR) is to identify which of the available strategies is the one being used by the agent, by simply observing the agent's actions and the environmental conditions during a certain period of time. The goal of Behavioral Cloning (BC) is more ambitious. In this last case, the learner must be able to build a model of the behavior of the agent. In both settings, the only assumption is that the learner has access to a training set that contains instances of observed behavioral traces for each available strategy. This paper studies a machine learning approach based on Probabilistic Finite Automata (PFAs), capable of achieving both the recognition and cloning tasks. We evaluate the performance of PFAs in the context of a simulated learning environment (in this case, a virtual Roomba vacuum cleaner robot), and compare it with a collection of other machine learning approaches.

  14. Magnetic guns with cylindrical permanent magnets

    DEFF Research Database (Denmark)

    Vokoun, David; Beleggia, Marco; Heller, Luděk

    2012-01-01

    The motion of a cylindrical permanent magnet (projectile) inside a tubular permanent magnet, with both magnets magnetized axially, illustrates nicely the physical principles behind the operation of magnetic guns. The force acting upon the projectile is expressed semi-analytically as derivative...... of the magnetostatic interaction energy. For comparison, the forces involved are also calculated numerically using finite elements methods. Based on the conservation of the magnetostatic and kinetic energies, the exit and asymptotic velocities are determined. The derived formulas can be used to optimize the generated...... forces and motion of the inner cylindrical magnet....

  15. 3D false color computed tomography for diagnosis and follow-up of permanent denervated human muscles submitted to home-based Functional Electrical Stimulation

    Directory of Open Access Journals (Sweden)

    Ugo Carraro

    2015-03-01

    Full Text Available This report outlines the use of a customized false-color 3D computed tomography (CT protocol for the imaging of the rectus femoris of spinal cord injury (SCI patients suffering from complete and permanent denervation, as characterized by complete Conus and Cauda Equina syndrome. This muscle imaging method elicits the progression of the syndrome from initial atrophy to eventual degeneration, as well as the extent to which patients' quadriceps could be recovered during four years of home-based functional electrical stimulation (h-b FES. Patients were pre-selected from several European hospitals and functionally tested by, and enrolled in the EU Commission Shared Cost Project RISE (Contract n. QLG5-CT-2001-02191 at the Department of Physical Medicine, Wilhelminenspital, Vienna, Austria. Denervated muscles were electrically stimulated using a custom-designed stimulator, large surface electrodes, and customized progressive stimulation settings. Spiral CT images and specialized computational tools were used to isolate the rectus femoris muscle and produce 3D and 2D reconstructions of the denervated muscles. The cross sections of the muscles were determined by 2D Color CT, while muscle volumes were reconstructed by 3D Color CT. Shape, volume, and density changes were measured over the entirety of each rectus femoris muscle. Changes in tissue composition within the muscle were visualized by associating different colors to specified Hounsfield unit (HU values for fat, (yellow: [-200; -10], loose connective tissue or atrophic muscle, (cyan: [-9; 40], and normal muscle, fascia and tendons included, (red: [41; 200]. The results from this analysis are presented as the average HU values within the rectus femoris muscle reconstruction, as well as the percentage of these tissues with respect to the total muscle volume. Results from this study demonstrate that h-b FES induces a compliance-dependent recovery of muscle volume and size of muscle fibers, as

  16. 3D False Color Computed Tomography for Diagnosis and Follow-Up of Permanent Denervated Human Muscles Submitted to Home-Based Functional Electrical Stimulation.

    Science.gov (United States)

    Carraro, Ugo; Edmunds, Kyle J; Gargiulo, Paolo

    2015-03-11

    This report outlines the use of a customized false-color 3D computed tomography (CT) protocol for the imaging of the rectus femoris of spinal cord injury (SCI) patients suffering from complete and permanent denervation, as characterized by complete Conus and Cauda Equina syndrome. This muscle imaging method elicits the progression of the syndrome from initial atrophy to eventual degeneration, as well as the extent to which patients' quadriceps could be recovered during four years of home-based functional electrical stimulation (h-b FES). Patients were pre-selected from several European hospitals and functionally tested by, and enrolled in the EU Commission Shared Cost Project RISE (Contract n. QLG5-CT-2001-02191) at the Department of Physical Medicine, Wilhelminenspital, Vienna, Austria. Denervated muscles were electrically stimulated using a custom-designed stimulator, large surface electrodes, and customized progressive stimulation settings. Spiral CT images and specialized computational tools were used to isolate the rectus femoris muscle and produce 3D and 2D reconstructions of the denervated muscles. The cross sections of the muscles were determined by 2D Color CT, while muscle volumes were reconstructed by 3D Color CT. Shape, volume, and density changes were measured over the entirety of each rectus femoris muscle. Changes in tissue composition within the muscle were visualized by associating different colors to specified Hounsfield unit (HU) values for fat, (yellow: [-200; -10]), loose connective tissue or atrophic muscle, (cyan: [-9; 40]), and normal muscle, fascia and tendons included, (red: [41; 200]). The results from this analysis are presented as the average HU values within the rectus femoris muscle reconstruction, as well as the percentage of these tissues with respect to the total muscle volume. Results from this study demonstrate that h-b FES induces a compliance-dependent recovery of muscle volume and size of muscle fibers, as evidenced by the

  17. Multispace Behavioral Model for Face-Based Affective Social Agents

    Directory of Open Access Journals (Sweden)

    DiPaola Steve

    2007-01-01

    Full Text Available This paper describes a behavioral model for affective social agents based on three independent but interacting parameter spaces: knowledge, personality, and mood. These spaces control a lower-level geometry space that provides parameters at the facial feature level. Personality and mood use findings in behavioral psychology to relate the perception of personality types and emotional states to the facial actions and expressions through two-dimensional models for personality and emotion. Knowledge encapsulates the tasks to be performed and the decision-making process using a specially designed XML-based language. While the geometry space provides an MPEG-4 compatible set of parameters for low-level control, the behavioral extensions available through the triple spaces provide flexible means of designing complicated personality types, facial expression, and dynamic interactive scenarios.

  18. Multispace Behavioral Model for Face-Based Affective Social Agents

    Directory of Open Access Journals (Sweden)

    Ali Arya

    2007-03-01

    Full Text Available This paper describes a behavioral model for affective social agents based on three independent but interacting parameter spaces: knowledge, personality, and mood. These spaces control a lower-level geometry space that provides parameters at the facial feature level. Personality and mood use findings in behavioral psychology to relate the perception of personality types and emotional states to the facial actions and expressions through two-dimensional models for personality and emotion. Knowledge encapsulates the tasks to be performed and the decision-making process using a specially designed XML-based language. While the geometry space provides an MPEG-4 compatible set of parameters for low-level control, the behavioral extensions available through the triple spaces provide flexible means of designing complicated personality types, facial expression, and dynamic interactive scenarios.

  19. Acceptance-based behavior therapy to promote HIV medication adherence.

    Science.gov (United States)

    Moitra, Ethan; Herbert, James D; Forman, Evan M

    2011-12-01

    A significant number of adults with HIV in the USA do not maintain adherence to highly active antiretroviral therapy (HAART) at adequate levels. Although traditional cognitive behavioral interventions have shown promise in promoting HAART adherence, acceptance-based behavior therapy (ABBT) may be particularly useful in this population. ABBT has the potential to overcome common avoidance-based barriers associated with poor adherence, including denial of various illness-related factors and avoidance of stigmatization. We describe the rationale for promoting psychological and behavioral acceptance in HIV-positive populations; outline an ABBT to promote HAART adherence targeting primary care patients from urban, minority, low socioeconomic backgrounds; and report preliminary qualitative observations of treatment feasibility and acceptability.

  20. A Reward-Based Behavioral Platform to Measure Neural Activity during Head-Fixed Behavior

    Directory of Open Access Journals (Sweden)

    Andrew H. Micallef

    2017-05-01

    Full Text Available Understanding the neural computations that contribute to behavior requires recording from neurons while an animal is behaving. This is not an easy task as most subcellular recording techniques require absolute head stability. The Go/No-Go sensory task is a powerful decision-driven task that enables an animal to report a binary decision during head-fixation. Here we discuss how to set up an Ardunio and Python based platform system to control a Go/No-Go sensory behavior paradigm. Using an Arduino micro-controller and Python-based custom written program, a reward can be delivered to the animal depending on the decision reported. We discuss the various components required to build the behavioral apparatus that can control and report such a sensory stimulus paradigm. This system enables the end user to control the behavioral testing in real-time and therefore it provides a strong custom-made platform for probing the neural basis of behavior.

  1. [Acceptance and mindfulness-based cognitive-behavioral therapies].

    Science.gov (United States)

    Ngô, Thanh-Lan

    2013-01-01

    Cognitive behavioral therapy (CBT) is one of the main approaches in psychotherapy. It teaches the patient to examine the link between dysfunctional thoughts and maladaptive behaviors and to re- evaluate the cognitive biases involved in the maintenance of symptoms by using strategies such as guided discovery. CBT is constantly evolving in part to improve its' effectiveness and accessibility. Thus in the last decade, increasingly popular approaches based on mindfulness and acceptance have emerged. These therapies do not attempt to modify cognitions even when they are biased and dysfunctional but rather seek a change in the relationship between the individual and the symptoms. This article aims to present the historical context that has allowed the emergence of this trend, the points of convergence and divergence with traditional CBT as well as a brief presentation of the different therapies based on mindfulness meditation and acceptance. Hayes (2004) described three successive waves in behavior therapy, each characterized by "dominant assumptions, methods and goals": traditional behavior therapy, cognitive therapy and therapies based on mindfulness meditation and acceptance. The latter consider that human suffering occurs when the individual lives a restricted life in order avoid pain and immediate discomfort to the detriment of his global wellbeing. These therapies combine mindfulness, experiential, acceptance strategies with traditional behavior principles in order to attain lasting results. There are significant points of convergence between traditional CBT and therapies based on mindfulness meditation and acceptance. They are both empirically validated, based upon a theoretical model postulating that avoidance is key in the maintenance of psychopathology and they recommend an approach strategy in order to overcome the identified problem. They both use behavioral techniques in the context of a collaborative relationship in order to identify precise problems and to

  2. Dealing with defaulting suppliers using behavioral based governance methods

    DEFF Research Database (Denmark)

    Prosman, Ernst Johannes; Scholten, Kirstin; Power, Damien

    2016-01-01

    Purpose: The aim of this paper is to explore factors influencing the effectiveness of buyer initiated Behavioral Based Governance Methods (BBGMs). The ability of BBGMs to improve supplier performance is assessed considering power imbalances and the resource intensiveness of the BBGM. Agency Theory...

  3. Biodegradable xylitol-based elastomers: In vivo behavior and biocompatibility

    NARCIS (Netherlands)

    J.P. Bruggeman (Joost); C.J. Bettinger (Christopher); R.S. Langer (Robert)

    2010-01-01

    textabstractBiodegradable elastomers based on polycondensation reactions of xylitol with sebacic acid, referred to as poly(xylitol sebacate) (PXS) elastomers have recently been developed. We describe the in vivo behavior of PXS elastomers. Four PXS elastomers were synthesized, characterized, and

  4. Behavioral, neurophysiological, and descriptive changes after occupation-based intervention.

    Science.gov (United States)

    Skubik-Peplaski, Camille; Carrico, Cheryl; Nichols, Laurel; Chelette, Kenneth; Sawaki, Lumy

    2012-01-01

    We evaluated the effects of occupation-based intervention on poststroke upper-extremity (UE) motor recovery, neuroplastic change, and occupational performance in 1 research participant. A 55-yr-old man with chronic stroke and moderately impaired UE motor function participated in 15 sessions of occupation-based intervention in a hospital setting designed to simulate a home environment. We tested behavioral motor function (Fugl-Meyer Assessment, Stroke Impact Scale, Canadian Occupational Performance Measure) and neuroplasticity (transcranial magnetic stimulation [TMS]) at baseline and at completion of intervention. We collected descriptive data on occupational participation throughout the study. All behavioral outcomes indicated clinically relevant improvement. TMS revealed bihemispheric corticomotor reorganization. Descriptive data revealed enhanced occupational performance. Occupation-based intervention delivered in a hospital-based, homelike environment can lead to poststroke neuroplastic change, increased functional use of the affected UE, and improved occupational performance. Copyright © 2012 by the American Occupational Therapy Association, Inc.

  5. Creating adaptive web recommendation system based on user behavior

    Science.gov (United States)

    Walek, Bogdan

    2018-01-01

    The paper proposes adaptive web recommendation system based on user behavior. The proposed system uses expert system to evaluating and recommending suitable items of content. Relevant items are subsequently evaluated and filtered based on history of visited items and user´s preferred categories of items. Main parts of the proposed system are presented and described. The proposed recommendation system is verified on specific example.

  6. Rethinking infant knowledge: toward an adaptive process account of successes and failures in object permanence tasks.

    Science.gov (United States)

    Munakata, Y; McClelland, J L; Johnson, M H; Siegler, R S

    1997-10-01

    Infants seem sensitive to hidden objects in habituation tasks at 3.5 months but fail to retrieve hidden objects until 8 months. The authors first consider principle-based accounts of these successes and failures, in which early successes imply knowledge of principles and failures are attributed to ancillary deficits. One account is that infants younger than 8 months have the object permanence principle but lack means-ends abilities. To test this, 7-month-olds were trained on means-ends behaviors and were tested on retrieval of visible and occluded toys. Means-ends demands were the same, yet infants made more toy-guided retrievals in the visible case. The authors offer an adaptive process account in which knowledge is graded and embedded in specific behavioral processes. Simulation models that learn gradually to represent occluded objects show how this approach can account for success and failure in object permanence tasks without assuming principles and ancillary deficits.

  7. [The Object Permanence Fallacy.] Commentary.

    Science.gov (United States)

    Bradley, Ben S.

    1996-01-01

    Suggests that Greenberg's challenge to the centrality of object permanence in developmental thinking reveals that developmentalists' theories about childhood speak about their own self-images. Notes that developmentalists have been guilty of not only the object permanence fallacy but also the genetic fallacy, or the mistaken belief that describing…

  8. Implementation of Permanent Magnet Motors in Electric Vehicles

    OpenAIRE

    Elvestad, Eirik

    2008-01-01

    This thesis has studied permanent magnet motors in electric vehicles (EVs) under the assumption that they are tractable due to a low weight and high compactness. The implementation has been investigated through a case study, which resulted in an EV simulation model. The model contains a maximal torque per ampere and a closed-loop field weakening controller. Abstract Faults are a special concern in permanent magnet motors. Fault sources and faulted behavior are addressed separately. The EV mo...

  9. A neural substrate for object permanence in monkey inferotemporal cortex

    OpenAIRE

    Puneeth, NC; Arun, SP

    2016-01-01

    We take it for granted that objects continue to exist after being occluded. This knowledge ? known as object permanence ? is present even in childhood, but its neural basis is not fully understood. Here, we show that monkey inferior temporal (IT) neurons carry potential signals of object permanence even in animals that received no explicit behavioral training. We compared two conditions with identical visual stimulation: the same object emerged from behind an occluder as expected following it...

  10. Method and apparatus for assembling a permanent magnet pole assembly

    Science.gov (United States)

    Carl, Jr., Ralph James; Bagepalli, Bharat Sampathkumaran [Niskayuna, NY; Jansen, Patrick Lee [Scotia, NY; Dawson, Richard Nils [Voorheesville, NY; Qu, Ronghai [Clifton Park, NY; Avanesov, Mikhail Avramovich [Moscow, RU

    2009-08-11

    A pole assembly for a rotor, the pole assembly includes a permanent magnet pole including at least one permanent magnet block, a plurality of laminations including a pole cap mechanically coupled to the pole, and a plurality of laminations including a base plate mechanically coupled to the pole.

  11. Energy based model for temperature dependent behavior of ferromagnetic materials

    International Nuclear Information System (INIS)

    Sah, Sanjay; Atulasimha, Jayasimha

    2017-01-01

    An energy based model for temperature dependent anhysteretic magnetization curves of ferromagnetic materials is proposed and benchmarked against experimental data. This is based on the calculation of macroscopic magnetic properties by performing an energy weighted average over all possible orientations of the magnetization vector. Most prior approaches that employ this method are unable to independently account for the effect of both inhomogeneity and temperature in performing the averaging necessary to model experimental data. Here we propose a way to account for both effects simultaneously and benchmark the model against experimental data from ~5 K to ~300 K for two different materials in both annealed (fewer inhomogeneities) and deformed (more inhomogeneities) samples. This demonstrates that this framework is well suited to simulate temperature dependent experimental magnetic behavior. - Highlights: • Energy based model for temperature dependent ferromagnetic behavior. • Simultaneously accounts for effect of temperature and inhomogeneities. • Benchmarked against experimental data from 5 K to 300 K.

  12. Behavior-based cleaning for unreliable RFID data sets.

    Science.gov (United States)

    Fan, Hua; Wu, Quanyuan; Lin, Yisong

    2012-01-01

    Radio Frequency IDentification (RFID) technology promises to revolutionize the way we track items and assets, but in RFID systems, missreading is a common phenomenon and it poses an enormous challenge to RFID data management, so accurate data cleaning becomes an essential task for the successful deployment of systems. In this paper, we present the design and development of a RFID data cleaning system, the first declarative, behavior-based unreliable RFID data smoothing system. We take advantage of kinematic characteristics of tags to assist in RFID data cleaning. In order to establish the conversion relationship between RFID data and kinematic parameters of the tags, we propose a movement behavior detection model. Moreover, a Reverse Order Filling Mechanism is proposed to ensure a more complete access to get the movement behavior characteristics of tag. Finally, we validate our solution with a common RFID application and demonstrate the advantages of our approach through extensive simulations.

  13. Behavior Identification Based on Geotagged Photo Data Set

    Directory of Open Access Journals (Sweden)

    Guo-qi Liu

    2014-01-01

    Full Text Available The popularity of mobile devices has produced a set of image data with geographic information, time information, and text description information, which is called geotagged photo data set. The division of this kind of data by its behavior and the location not only can identify the user’s important location and daily behavior, but also helps users to sort the huge image data. This paper proposes a method to build an index based on multiple classification result, which can divide the data set multiple times and distribute labels to the data to build index according to the estimated probability of classification results in order to accomplish the identification of users’ important location and daily behaviors. This paper collects 1400 discrete sets of data as experimental data to verify the method proposed in this paper. The result of the experiment shows that the index and actual tagging results have a high inosculation.

  14. Promoting Behavior-Based Energy Efficiency in Military Housing

    Energy Technology Data Exchange (ETDEWEB)

    AH McMakin; EL Malone; RE Lundgren

    1999-09-07

    The U.S. Department of Energy's Federal Energy Management Program (FEMP) helps agencies reduce the cost of doing business through energy efficiency, water conservation, and the use of solar and other renewable energy. As a large energy user, the U.S. military has been one of the government sectors of focus. Several military installations have shown substantial energy savings in past years. Most of these efficiency projects, however, have focused primarily on physical upgrades, technologies, and purchasing habits. Furthermost projects have focused on administrative and operational areas of energy use. Military residential housing, in particular, has received little formal attention for energy efficiency involving behaviors of the residents themselves. Behavior-based change is a challenging, but potentially fruitful area for energy conservation programs. However, behavioral change involves links with values, social networks and organizations, and new ways of thinking about living patterns. This handbook attempts to fill a gap by offering guidance for promoting such efforts.

  15. An Ontology-Based Framework for Modeling User Behavior

    DEFF Research Database (Denmark)

    Razmerita, Liana

    2011-01-01

    and classifies its users according to their behavior. The user ontology is the backbone of OntobUMf and has been designed according to the Information Management System Learning Information Package (IMS LIP). The user ontology includes a Behavior concept that extends IMS LIP specification and defines...... characteristics of the users interacting with the system. Concrete examples of how OntobUMf is used in the context of a Knowledge Management (KM) System are provided. This paper discusses some of the implications of ontology-based user modeling for semantically enhanced KM and, in particular, for personal KM....... The results of this research may contribute to the development of other frameworks for modeling user behavior, other semantically enhanced user modeling frameworks, or other semantically enhanced information systems....

  16. BARTER: Behavior Profile Exchange for Behavior-Based Admission and Access Control in MANETs

    Science.gov (United States)

    Frias-Martinez, Vanessa; Stolfo, Salvatore J.; Keromytis, Angelos D.

    Mobile Ad-hoc Networks (MANETs) are very dynamic networks with devices continuously entering and leaving the group. The highly dynamic nature of MANETs renders the manual creation and update of policies associated with the initial incorporation of devices to the MANET (admission control) as well as with anomaly detection during communications among members (access control) a very difficult task. In this paper, we present BARTER, a mechanism that automatically creates and updates admission and access control policies for MANETs based on behavior profiles. BARTER is an adaptation for fully distributed environments of our previously introduced BB-NAC mechanism for NAC technologies. Rather than relying on a centralized NAC enforcer, MANET members initially exchange their behavior profiles and compute individual local definitions of normal network behavior. During admission or access control, each member issues an individual decision based on its definition of normalcy. Individual decisions are then aggregated via a threshold cryptographic infrastructure that requires an agreement among a fixed amount of MANET members to change the status of the network. We present experimental results using content and volumetric behavior profiles computed from the ENRON dataset. In particular, we show that the mechanism achieves true rejection rates of 95% with false rejection rates of 9%.

  17. Bubble behavior characteristics based on virtual binocular stereo vision

    Science.gov (United States)

    Xue, Ting; Xu, Ling-shuang; Zhang, Shang-zhen

    2018-01-01

    The three-dimensional (3D) behavior characteristics of bubble rising in gas-liquid two-phase flow are of great importance to study bubbly flow mechanism and guide engineering practice. Based on the dual-perspective imaging of virtual binocular stereo vision, the 3D behavior characteristics of bubbles in gas-liquid two-phase flow are studied in detail, which effectively increases the projection information of bubbles to acquire more accurate behavior features. In this paper, the variations of bubble equivalent diameter, volume, velocity and trajectory in the rising process are estimated, and the factors affecting bubble behavior characteristics are analyzed. It is shown that the method is real-time and valid, the equivalent diameter of the rising bubble in the stagnant water is periodically changed, and the crests and troughs in the equivalent diameter curve appear alternately. The bubble behavior characteristics as well as the spiral amplitude are affected by the orifice diameter and the gas volume flow.

  18. The Effect of Training on Adopting Behaviors Preventing from Knee Osteoarthritis Based on Planned Behavior Theory

    Directory of Open Access Journals (Sweden)

    S

    2015-05-01

    Full Text Available Introduction: the arthritis is believed to be among common diseases which prevail in the developed and developing countries, including Iran. In demographic studies, the prevalence of knee arthritis which stands at %15/3 in the population above 15-years old was shown. Owing to the fact that societies are about to be aged than before, the issue has become a growing significance in the subject matter of public health. The present study is conducted with an aim to investigate into the effect of training based on the planned behavior model on preventing the teachers of preliminary schools from getting knee arthritis. Methods: the study as an intervention research is of quasi-experimental kind. The population in question included 114 individuals among female teachers of preliminary schools who were brought to the study randomly and divided into two groups intervention and non-intervention. Based on the primary results, the educational contents were designed and submitted in the intervention group. After two months of executing the training program, the post test was carried out. The data was analyzed by SPSS version 18. Due to the loss of normality in data distribution, non- parametric tests were used. Results: the study demonstrated that the components of the planned behavior theory (i.e. the attitudes, subjective norms and the control of perceived behavior could altogether estimate %37 of intention and %43 of behavior. Meanwhile, the role of subjective norms (β =56/0 in predicting intention was overriding, In this study,after the educational program, control of perceived behavior scores increased of 32/50 ± 4/05 to 34/82 ± 5/66. indicating that the major obstacles in adopting behaviors preventing from knee arthritis are the lack of regular physical activity (%72/4 and failure to use western-style toilet (%57. Conclusion: In this Study the effect theory of planned behavior support in predicting exercise intentions and behavior in the prevention of

  19. Management of REM sleep behavior disorder: An evidence based review.

    Science.gov (United States)

    Devnani, Preeti; Fernandes, Racheal

    2015-01-01

    Rapid eye movement (REM) sleep behavior disorder (RBD) is characterized by dream enactment behavior resulting from a loss of REM skeletal muscle atonia. The neurobiology of REM sleep and the characteristic features of REM atonia have an important basis for understanding the aggravating etiologies the proposed pharmacological interventions in its management. This review outlines the evidence for behavioral and therapeutic measures along with evidence-based guidelines for their implementation, impact on falls, and effect on polysomnography (PSG) while highlighting the non-motor, autonomic, and cognitive impact of this entity. PubMed databases were reviewed upto May 2013 in peer-reviewed scientific literature regarding the pathophysiology and management of RBD in adults. The literature was graded according to the Oxford centre of evidence-based Medicine Levels. An early intervention that helps prevent consequences such as falls and provides a base for intervention with neuroprotective mechanisms and allocates a unique platform that RBD portrays with its high risk of disease conversion with a sufficiently long latency. RBD provides a unique platform with its high risk of disease conversion with a sufficiently long latency, providing an opportunity for early intervention both to prevent consequences such as falls and provide a base for intervention with neuroprotective mechanisms.

  20. Management of REM sleep behavior disorder: An evidence based review

    Directory of Open Access Journals (Sweden)

    Preeti Devnani

    2015-01-01

    Full Text Available Rapid eye movement (REM sleep behavior disorder (RBD is characterized by dream enactment behavior resulting from a loss of REM skeletal muscle atonia. The neurobiology of REM sleep and the characteristic features of REM atonia have an important basis for understanding the aggravating etiologies the proposed pharmacological interventions in its management. This review outlines the evidence for behavioral and therapeutic measures along with evidence-based guidelines for their implementation, impact on falls, and effect on polysomnography (PSG while highlighting the non-motor, autonomic, and cognitive impact of this entity. PubMed databases were reviewed upto May 2013 in peer-reviewed scientific literature regarding the pathophysiology and management of RBD in adults. The literature was graded according to the Oxford centre of evidence-based Medicine Levels. An early intervention that helps prevent consequences such as falls and provides a base for intervention with neuroprotective mechanisms and allocates a unique platform that RBD portrays with its high risk of disease conversion with a sufficiently long latency. RBD provides a unique platform with its high risk of disease conversion with a sufficiently long latency, providing an opportunity for early intervention both to prevent consequences such as falls and provide a base for intervention with neuroprotective mechanisms.

  1. Hydration behaviors of calcium silicate-based biomaterials.

    Science.gov (United States)

    Lee, Yuan-Ling; Wang, Wen-Hsi; Lin, Feng-Huie; Lin, Chun-Pin

    2017-06-01

    Calcium silicate (CS)-based biomaterials, such as mineral trioxide aggregate (MTA), have become the most popular and convincing material used in restorative endodontic treatments. However, the commercially available CS-based biomaterials all contain different minor additives, which may affect their hydration behaviors and material properties. The purpose of this study was to evaluate the hydration behavior of CS-based biomaterials with/without minor additives. A novel CS-based biomaterial with a simplified composition, without mineral oxides as minor additives, was produced. The characteristics of this biomaterial during hydration were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR) spectrometry. The hydration behaviors of commercially available gray and white MTAs with mineral oxide as minor additives were also evaluated for reference. For all three test materials, the XRD analysis revealed similar diffraction patterns after hydration, but MTAs presented a significant decrease in the intensities of Bi 2 O 3 -related peaks. SEM results demonstrated similar porous microstructures with some hexagonal and facetted crystals on the outer surfaces. In addition, compared to CS with a simplified composition, the FTIR plot indicated that hydrated MTAs with mineral oxides were better for the polymerization of calcium silicate hydrate (CSH), presenting Si-O band shifting to higher wave numbers, and contained more water crystals within CSH, presenting sharper bands for O-H bending. Mineral oxides might not result in significant changes in the crystal phases or microstructures during the hydration of CS-based biomaterials, but these compounds affected the hydration behavior at the molecular level. Copyright © 2016. Published by Elsevier B.V.

  2. Topology optimized permanent magnet systems

    Science.gov (United States)

    Bjørk, R.; Bahl, C. R. H.; Insinga, A. R.

    2017-09-01

    Topology optimization of permanent magnet systems consisting of permanent magnets, high permeability iron and air is presented. An implementation of topology optimization for magnetostatics is discussed and three examples are considered. The Halbach cylinder is topology optimized with iron and an increase of 15% in magnetic efficiency is shown. A topology optimized structure to concentrate a homogeneous field is shown to increase the magnitude of the field by 111%. Finally, a permanent magnet with alternating high and low field regions is topology optimized and a Λcool figure of merit of 0.472 is reached, which is an increase of 100% compared to a previous optimized design.

  3. Topology optimized permanent magnet systems

    DEFF Research Database (Denmark)

    Bjørk, Rasmus; Bahl, Christian; Insinga, Andrea Roberto

    2017-01-01

    Topology optimization of permanent magnet systems consisting of permanent magnets, high permeability iron and air is presented. An implementation of topology optimization for magnetostatics is discussed and three examples are considered. The Halbach cylinder is topology optimized with iron...... and an increase of 15% in magnetic efficiency is shown. A topology optimized structure to concentrate a homogeneous field is shown to increase the magnitude of the field by 111%. Finally, a permanent magnet with alternating high and low field regions is topology optimized and a ΛcoolΛcool figure of merit of 0...

  4. Periodic permanent magnet focused klystron

    Science.gov (United States)

    Ferguson, Patrick; Read, Michael; Ives, R Lawrence

    2015-04-21

    A periodic permanent magnet (PPM) klystron has beam transport structures and RF cavity structures, each of which has permanent magnets placed substantially equidistant from a beam tunnel formed about the central axis, and which are also outside the extent of a cooling chamber. The RF cavity sections also have permanent magnets which are placed substantially equidistant from the beam tunnel, but which include an RF cavity coupling to the beam tunnel for enhancement of RF carried by an electron beam in the beam tunnel.

  5. The Evidence-Based Practice of Applied Behavior Analysis.

    Science.gov (United States)

    Slocum, Timothy A; Detrich, Ronnie; Wilczynski, Susan M; Spencer, Trina D; Lewis, Teri; Wolfe, Katie

    2014-05-01

    Evidence-based practice (EBP) is a model of professional decision-making in which practitioners integrate the best available evidence with client values/context and clinical expertise in order to provide services for their clients. This framework provides behavior analysts with a structure for pervasive use of the best available evidence in the complex settings in which they work. This structure recognizes the need for clear and explicit understanding of the strength of evidence supporting intervention options, the important contextual factors including client values that contribute to decision making, and the key role of clinical expertise in the conceptualization, intervention, and evaluation of cases. Opening the discussion of EBP in this journal, Smith (The Behavior Analyst, 36, 7-33, 2013) raised several key issues related to EBP and applied behavior analysis (ABA). The purpose of this paper is to respond to Smith's arguments and extend the discussion of the relevant issues. Although we support many of Smith's (The Behavior Analyst, 36, 7-33, 2013) points, we contend that Smith's definition of EBP is significantly narrower than definitions that are used in professions with long histories of EBP and that this narrowness conflicts with the principles that drive applied behavior analytic practice. We offer a definition and framework for EBP that aligns with the foundations of ABA and is consistent with well-established definitions of EBP in medicine, psychology, and other professions. In addition to supporting the systematic use of research evidence in behavior analytic decision making, this definition can promote clear communication about treatment decisions across disciplines and with important outside institutions such as insurance companies and granting agencies.

  6. "Psychological Boarding" and Community-Based Behavioral Health Crisis Stabilization.

    Science.gov (United States)

    Mukherjee, Dhrubodhi; Saxon, Verletta

    2018-01-27

    This exploratory paper presents a case study where a community based mental health organization forging a partnership with a local hospital system to establish a crisis stabilization unit (CSU) to address behavioral health emergency care. The study takes a mixed methods case study approach to address two research questions; (a) did this approach reduce the overall length of stay in the hospital emergency departments? (b) What challenges did the taskforce face in implementing this CSU model? The paper shares recommendation from the findings.

  7. Enhanced Control for a Direct-driven Permanent Synchronous Generator Wind-power Generation System with Flywheel Energy Storage Unit Under Unbalanced Grid Fault

    DEFF Research Database (Denmark)

    Yao, Jun; Zhou, Te; Hu, Weihao

    2015-01-01

    This article presents an enhanced control strategy for a direct-driven permanent synchronous generator based wind-power generation system with a flywheel energy storage unit. The behaviors of the direct-driven permanent magnet synchronous generator system with a flywheel energy storage unit under......, the DC-link voltage oscillations can be effectively suppressed during the unbalanced grid fault by controlling the flywheel energy storage unit. Furthermore, a proportional–integral-resonant controller is designed for the flywheel motor to eliminate the oscillations in the DC-link voltage. Finally......, the proposed coordinated control strategy for the direct-driven permanent magnet synchronous generator system with a flywheel energy storage unit has been validated by the simulation results of a 1-MW direct-driven permanent magnet synchronous generator wind power generation system with a flywheel energy...

  8. Extending Theory-Based Quantitative Predictions to New Health Behaviors.

    Science.gov (United States)

    Brick, Leslie Ann D; Velicer, Wayne F; Redding, Colleen A; Rossi, Joseph S; Prochaska, James O

    2016-04-01

    Traditional null hypothesis significance testing suffers many limitations and is poorly adapted to theory testing. A proposed alternative approach, called Testing Theory-based Quantitative Predictions, uses effect size estimates and confidence intervals to directly test predictions based on theory. This paper replicates findings from previous smoking studies and extends the approach to diet and sun protection behaviors using baseline data from a Transtheoretical Model behavioral intervention (N = 5407). Effect size predictions were developed using two methods: (1) applying refined effect size estimates from previous smoking research or (2) using predictions developed by an expert panel. Thirteen of 15 predictions were confirmed for smoking. For diet, 7 of 14 predictions were confirmed using smoking predictions and 6 of 16 using expert panel predictions. For sun protection, 3 of 11 predictions were confirmed using smoking predictions and 5 of 19 using expert panel predictions. Expert panel predictions and smoking-based predictions poorly predicted effect sizes for diet and sun protection constructs. Future studies should aim to use previous empirical data to generate predictions whenever possible. The best results occur when there have been several iterations of predictions for a behavior, such as with smoking, demonstrating that expected values begin to converge on the population effect size. Overall, the study supports necessity in strengthening and revising theory with empirical data.

  9. Lawful Permanent Residents Fiscal Year 2014 Country

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  10. Lawful Permanent Residents Fiscal Year 2011 State

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  11. Lawful Permanent Residents Fiscal Year 2015 Country

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  12. Lawful Permanent Residents Fiscal Year 2016 State

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  13. Lawful Permanent Residents Fiscal Year 2014 State

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  14. Lawful Permanent Residents Fiscal Year 2015 State

    Data.gov (United States)

    Department of Homeland Security — Lawful permanent residents (LPRs) are foreign nationals who have been granted the right to reside permanently in the United States. LPRs are also known as 'permanent...

  15. Behavior-based safety on construction sites: a case study.

    Science.gov (United States)

    Choudhry, Rafiq M

    2014-09-01

    This work presents the results of a case study and describes an important area within the field of construction safety management, namely behavior-based safety (BBS). This paper adopts and develops a management approach for safety improvements in construction site environments. A rigorous behavioral safety system and its intervention program was implemented and deployed on target construction sites. After taking a few weeks of safety behavior measurements, the project management team implemented the designed intervention and measurements were taken. Goal-setting sessions were arranged on-site with workers' participation to set realistic and attainable targets of performance. Safety performance measurements continued and the levels of performance and the targets were presented on feedback charts. Supervisors were asked to give workers recognition and praise when they acted safely or improved critical behaviors. Observers were requested to have discussions with workers, visit the site, distribute training materials to workers, and provide feedback to crews and display charts. They were required to talk to operatives in the presence of line managers. It was necessary to develop awareness and understanding of what was being measured. In the process, operatives learned how to act safely when conducting site tasks using the designed checklists. Current weekly scores were discussed in the weekly safety meetings and other operational site meetings with emphasis on how to achieve set targets. The reliability of the safety performance measures taken by the company's observers was monitored. A clear increase in safety performance level was achieved across all categories: personal protective equipment; housekeeping; access to heights; plant and equipment, and scaffolding. The research reveals that scores of safety performance at one project improved from 86% (at the end of 3rd week) to 92.9% during the 9th week. The results of intervention demonstrated large decreases in

  16. Thermal behaviors of liquid La-based bulk metallic glasses

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, D. W.; Wang, X. D., E-mail: wangxd@zju.edu.cn, E-mail: jiangjz@zju.edu.cn; Lou, H. B.; Cao, Q. P.; Jiang, J. Z., E-mail: wangxd@zju.edu.cn, E-mail: jiangjz@zju.edu.cn [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Wang, L. W. [Institute of Materials Science and Engineering, Lanzhou University, Lanzhou 730000 (China); Zhang, D. X. [State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou 310027 (China)

    2014-12-14

    Thermal behaviors of liquid La-based bulk metallic glasses have been measured by using the dilatometer with a self-sealed sample cell. It is demonstrated that the strong glass forming liquid not only has the small thermal expansion coefficient but also shows the slow variation rate. Moreover, the strong glass former has relatively dense atomic packing and also small density change in the liquid state. The results suggest that the high glass forming ability of La-based metallic glasses would be closely related to the slow atomic rearrangements in liquid melts.

  17. High temperature oxidation behavior of TiAl-based intermetallics

    International Nuclear Information System (INIS)

    Stroosnijder, M.F.; Sunderkoetter, J.D.; Haanappel, V.A.C.

    1996-01-01

    TiAl-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 C. In the present contribution some general aspects of high temperature oxidation of TiAl-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behavior of such materials

  18. Creep Behavior of Poly(lactic acid Based Biocomposites

    Directory of Open Access Journals (Sweden)

    Marco Morreale

    2017-04-01

    Full Text Available Polymer composites containing natural fibers are receiving growing attention as possible alternatives for composites containing synthetic fibers. The use of biodegradable matrices obtained from renewable sources in replacement for synthetic ones is also increasing. However, only limited information is available about the creep behavior of the obtained composites. In this work, the tensile creep behavior of PLA based composites, containing flax and jute twill weave woven fabrics, produced through compression molding, was investigated. Tensile creep tests were performed at different temperatures (i.e., 40 and 60 °C. The results showed that the creep behavior of the composites is strongly influenced by the temperature and the woven fabrics used. As preliminary characterization, quasi-static tensile tests and dynamic mechanical tests were carried out on the composites. Furthermore, fabrics (both flax and jute were tested as received by means of quasi-static tests and creep tests to evaluate the influence of fabrics mechanical behavior on the mechanical response of the resulting composites. The morphological analysis of the fracture surface of the tensile samples showed the better fiber-matrix adhesion between PLA and jute fabric.

  19. APF-Based Car Following Behavior Considering Lateral Distance

    Directory of Open Access Journals (Sweden)

    Zhao-Sheng Yang

    2013-01-01

    Full Text Available Considering the influence of lateral distance on consecutive vehicles, this paper proposes a new car following model based on the artificial potential field theory (APF. Traditional car following behaviors all assume that the vehicles are driving along the middle of a lane. Different from the traditional car following principles, this incorporation of APF offers a potential breakthrough in the fields of car following theory. The individual vehicle can be represented as a unit point charge in electric field, and the interaction of the attractive potential energy and the repellent potential energy between vehicles simplifies the various influence factors on the target vehicle in actual following behavior. Consequently, it can make a better analysis of the following behavior under the lateral separation. Then, the proposed model has been demonstrated in simulation environment, through which the space-time trajectories and the potential energy change regulation are obtained. Simulations verify that the following vehicle's behavior is vulnerable to be affected by lateral distance, where the attractive potential energy tends to become repellent potential energy as the longitudinal distance decreases. The search results prove that the proposed model quantifies the relations between headway and potential energy and better reflects the following process in real-world situation.

  20. Creep Behavior of Poly(lactic acid) Based Biocomposites.

    Science.gov (United States)

    Morreale, Marco; Mistretta, Maria Chiara; Fiore, Vincenzo

    2017-04-08

    Polymer composites containing natural fibers are receiving growing attention as possible alternatives for composites containing synthetic fibers. The use of biodegradable matrices obtained from renewable sources in replacement for synthetic ones is also increasing. However, only limited information is available about the creep behavior of the obtained composites. In this work, the tensile creep behavior of PLA based composites, containing flax and jute twill weave woven fabrics, produced through compression molding, was investigated. Tensile creep tests were performed at different temperatures (i.e., 40 and 60 °C). The results showed that the creep behavior of the composites is strongly influenced by the temperature and the woven fabrics used. As preliminary characterization, quasi-static tensile tests and dynamic mechanical tests were carried out on the composites. Furthermore, fabrics (both flax and jute) were tested as received by means of quasi-static tests and creep tests to evaluate the influence of fabrics mechanical behavior on the mechanical response of the resulting composites. The morphological analysis of the fracture surface of the tensile samples showed the better fiber-matrix adhesion between PLA and jute fabric.

  1. Translational behavioral medicine for population and individual health: gaps, opportunities, and vision for practice-based translational behavior change research.

    Science.gov (United States)

    Ma, Jun; Lewis, Megan A; Smyth, Joshua M

    2018-04-12

    In this commentary, we propose a vision for "practice-based translational behavior change research," which we define as clinical and public health practice-embedded research on the implementation, optimization, and fundamental mechanisms of behavioral interventions. This vision intends to be inclusive of important research elements for behavioral intervention development, testing, and implementation. We discuss important research gaps and conceptual and methodological advances in three key areas along the discovery (development) to delivery (implementation) continuum of evidence-based interventions to improve behavior and health that could help achieve our vision of practice-based translational behavior change research. We expect our proposed vision to be refined and evolve over time. Through highlighting critical gaps that can be addressed by integrating modern theoretical and methodological approaches across disciplines in behavioral medicine, we hope to inspire the development and funding of innovative research on more potent and implementable behavior change interventions for optimal population and individual health.

  2. Tuning permanent magnets with adjustable field clamps

    International Nuclear Information System (INIS)

    Schermer, R.I.

    1987-01-01

    The effective length of a permanent-magnet assembly can be varied by adjusting the geometrical parameters of a field clamp. This paper presents measurements on a representative dipole and quadrupole as the field clamp is withdrawn axially or radially. The detailed behavior depends upon the magnet multipolarity and geometry. As a rule-of-thumb, a 3-mm-thick iron plate placed at one end plane of the magnet will shorten the length by one-third of the magnet bore radius

  3. Automated Clinical Assessment from Smart home-based Behavior Data

    Science.gov (United States)

    Dawadi, Prafulla Nath; Cook, Diane Joyce; Schmitter-Edgecombe, Maureen

    2016-01-01

    Smart home technologies offer potential benefits for assisting clinicians by automating health monitoring and well-being assessment. In this paper, we examine the actual benefits of smart home-based analysis by monitoring daily behaviour in the home and predicting standard clinical assessment scores of the residents. To accomplish this goal, we propose a Clinical Assessment using Activity Behavior (CAAB) approach to model a smart home resident’s daily behavior and predict the corresponding standard clinical assessment scores. CAAB uses statistical features that describe characteristics of a resident’s daily activity performance to train machine learning algorithms that predict the clinical assessment scores. We evaluate the performance of CAAB utilizing smart home sensor data collected from 18 smart homes over two years using prediction and classification-based experiments. In the prediction-based experiments, we obtain a statistically significant correlation (r = 0.72) between CAAB-predicted and clinician-provided cognitive assessment scores and a statistically significant correlation (r = 0.45) between CAAB-predicted and clinician-provided mobility scores. Similarly, for the classification-based experiments, we find CAAB has a classification accuracy of 72% while classifying cognitive assessment scores and 76% while classifying mobility scores. These prediction and classification results suggest that it is feasible to predict standard clinical scores using smart home sensor data and learning-based data analysis. PMID:26292348

  4. The effect of education based on the Theory of Planned Behavior in smoking

    Directory of Open Access Journals (Sweden)

    Mahmoud Barfi

    2018-03-01

    Conclusion: According to the results, Education based on the theory of planned behavior has a positive impact on smoking behavior, Therefore, it is recommended that the above educational model is used to modify the behavior of smokers.

  5. Analysis and Speed Ripple Mitigation of a Space Vector Pulse Width Modulation-Based Permanent Magnet Synchronous Motor with a Particle Swarm Optimization Algorithm

    Directory of Open Access Journals (Sweden)

    Xing Liu

    2016-11-01

    Full Text Available A method is proposed for reducing speed ripple of permanent magnet synchronous motors (PMSMs controlled by space vector pulse width modulation (SVPWM. A flux graph and mathematics are used to analyze the speed ripple characteristics of the PMSM. Analysis indicates that the 6P (P refers to pole pairs of the PMSM time harmonic of rotor mechanical speed is the main harmonic component in the SVPWM control PMSM system. To reduce PMSM speed ripple, harmonics are superposed on a SVPWM reference signal. A particle swarm optimization (PSO algorithm is proposed to determine the optimal phase and multiplier coefficient of the superposed harmonics. The results of a Fourier decomposition and an optimized simulation model verified the accuracy of the analysis as well as the effectiveness of the speed ripple reduction methods, respectively.

  6. BEHAVIOR BASED CREDIT CARD FRAUD DETECTION USING SUPPORT VECTOR MACHINES

    Directory of Open Access Journals (Sweden)

    V. Dheepa

    2012-07-01

    Full Text Available Along with the great increase of internet and e-commerce, the use of credit card is an unavoidable one. Due to the increase of credit card usage, the frauds associated with this have also increased. There are a lot of approaches used to detect the frauds. In this paper, behavior based classification approach using Support Vector Machines are employed and efficient feature extraction method also adopted. If any discrepancies occur in the behaviors transaction pattern then it is predicted as suspicious and taken for further consideration to find the frauds. Generally credit card fraud detection problem suffers from a large amount of data, which is rectified by the proposed method. Achieving finest accuracy, high fraud catching rate and low false alarms are the main tasks of this approach.

  7. Permanent Magnet Eddy Current Loss Analysis of a Novel Motor Integrated Permanent Magnet Gear

    DEFF Research Database (Denmark)

    Zhang, Yuqiu; Lu, Kaiyuan; Ye, Yunyue

    2012-01-01

    In this paper, a new motor integrated permanent magnet gear (MIPMG) is discussed. The focus is on eddy current loss analysis associated to permanent magnets (PMs). A convenient model of MIPMG is provided based on 2-D field-motion coupled time-stepping finite element method for transient eddy...... current analysis. The model takes the eddy current effect of PMs into account in determination of the magnetic field in the air-gap and in the magnet regions. The eddy current losses generated in the magnets are properly interpreted. Design improvements for reducing the eddy current losses are suggested...

  8. Intervention Strategies Based on Information-Motivation-Behavioral Skills Model for Health Behavior Change: A Systematic Review

    OpenAIRE

    Chang, Sun Ju; Choi, Suyoung; Kim, Se-An; Song, Misoon

    2014-01-01

    Purpose: This study systematically reviewed research on behavioral interventions based on the information-motivation-behavioral skills (IMB) model to investigate specific intervention strategies that focus on information, motivation, and behavioral skills and to evaluate their effectiveness for people with chronic diseases. Methods: A systematic review was conducted in accordance with the guidelines of both the National Evidence-based Healthcare Collaborating Agency and Im and Chang. A lit...

  9. A computational study of nodal-based tetrahedral element behavior.

    Energy Technology Data Exchange (ETDEWEB)

    Gullerud, Arne S.

    2010-09-01

    This report explores the behavior of nodal-based tetrahedral elements on six sample problems, and compares their solution to that of a corresponding hexahedral mesh. The problems demonstrate that while certain aspects of the solution field for the nodal-based tetrahedrons provide good quality results, the pressure field tends to be of poor quality. Results appear to be strongly affected by the connectivity of the tetrahedral elements. Simulations that rely on the pressure field, such as those which use material models that are dependent on the pressure (e.g. equation-of-state models), can generate erroneous results. Remeshing can also be strongly affected by these issues. The nodal-based test elements as they currently stand need to be used with caution to ensure that their numerical deficiencies do not adversely affect critical values of interest.

  10. Rule-Based vs. Behavior-Based Self-Deployment for Mobile Wireless Sensor Networks.

    Science.gov (United States)

    Urdiales, Cristina; Aguilera, Francisco; González-Parada, Eva; Cano-García, Jose; Sandoval, Francisco

    2016-07-07

    In mobile wireless sensor networks (MWSN), nodes are allowed to move autonomously for deployment. This process is meant: (i) to achieve good coverage; and (ii) to distribute the communication load as homogeneously as possible. Rather than optimizing deployment, reactive algorithms are based on a set of rules or behaviors, so nodes can determine when to move. This paper presents an experimental evaluation of both reactive deployment approaches: rule-based and behavior-based ones. Specifically, we compare a backbone dispersion algorithm with a social potential fields algorithm. Most tests are done under simulation for a large number of nodes in environments with and without obstacles. Results are validated using a small robot network in the real world. Our results show that behavior-based deployment tends to provide better coverage and communication balance, especially for a large number of nodes in areas with obstacles.

  11. Motor Integrated Permanent Magnet Gear with a Wide Torque-Speed Range

    DEFF Research Database (Denmark)

    Rasmussen, Peter Omand; Matzen, Torben N.; Jahns, T. M.

    2009-01-01

    This paper present a new motor integrated permanent magnet gear with a wide torque-speed range. In the paper a 35 kW permanent magnet motor with a base speed of 4000 rpm and a top speed of 14000 rpm is integrated into a permanent magnetic gear with a gearing ratio of 8.67. The design process...

  12. Rare earth permanent magnets

    International Nuclear Information System (INIS)

    Higuchi, Akira

    1992-01-01

    This paper is a review of the new technologies for Nd-Fe-B magnets, their markets and future perspectives. This type of magnet is a product approaching the ideal magnet, and is based upon the development history of two previous generations of Sm-Co alloy systems and the recent progress on physical and metallurgical research. (orig.)

  13. Sensorless Control of Permanent Magnet Synchronous Machines

    DEFF Research Database (Denmark)

    Matzen, Torben N.

    Permanent magnet machines, with either surface mounted or embedded magnets on the rotor, are becoming more common due to the key advantages of higher energy conversion efficiency and higher torque density compared to the classical induction machine. Besides energy efficiency the permanent magnet...... the synchronous machine requires knowledge of the rotor shaft position due to the synchronous and undamped nature of the machine. The rotor position may be measured using a mechanical sensor, but the sensor reduces reliability and adds cost to the system and for this reason sensorless control methods started...... are dependent on the phase currents and rotor position. Based on the flux linkages the differential inductances are determined and used to establish the inductance saliency in terms of ratio and orientation. The orientation and its dependence on the current and rotor position are used to analyse the behaviour...

  14. Rotor Speed Control of a Direct-Driven Permanent Magnet Synchronous Generator-Based Wind Turbine Using Phase-Lag Compensators to Optimize Wind Power Extraction

    Directory of Open Access Journals (Sweden)

    Ester Hamatwi

    2017-01-01

    Full Text Available Due to the intermittent nature of wind, the wind power output tends to be inconsistent, and hence maximum power point tracking (MPPT is usually employed to optimize the power extracted from the wind resource at a wide range of wind speeds. This paper deals with the rotor speed control of a 2 MW direct-driven permanent magnet synchronous generator (PMSG to achieve MPPT. The proportional-integral (PI, proportional-derivative (PD, and proportional-integral-derivative (PID controllers have widely been employed in MPPT studies owing to their simple structure and simple design procedure. However, there are a number of shortcomings associated with these controllers; the trial-and-error design procedure used to determine the P, I, and D gains presents a possibility for poorly tuned controller gains, which reduces the accuracy and the dynamic performance of the entire control system. Moreover, these controllers’ linear nature, constricted operating range, and their sensitivity to changes in machine parameters make them ineffective when applied to nonlinear and uncertain systems. On the other hand, phase-lag compensators are associated with a design procedure that is well defined from fundamental principles as opposed to the aforementioned trial-and-error design procedure. This makes the latter controller type more accurate, although it is not well developed yet, and hence it is the focus of this paper. The simulation results demonstrated the effectiveness of the proposed MPPT controller.

  15. An imputation/copula-based stochastic individual tree growth model for mixed species Acadian forests: a case study using the Nova Scotia permanent sample plot network

    Directory of Open Access Journals (Sweden)

    John A. KershawJr

    2017-09-01

    Full Text Available Background A novel approach to modelling individual tree growth dynamics is proposed. The approach combines multiple imputation and copula sampling to produce a stochastic individual tree growth and yield projection system. Methods The Nova Scotia, Canada permanent sample plot network is used as a case study to develop and test the modelling approach. Predictions from this model are compared to predictions from the Acadian variant of the Forest Vegetation Simulator, a widely used statistical individual tree growth and yield model. Results Diameter and height growth rates were predicted with error rates consistent with those produced using statistical models. Mortality and ingrowth error rates were higher than those observed for diameter and height, but also were within the bounds produced by traditional approaches for predicting these rates. Ingrowth species composition was very poorly predicted. The model was capable of reproducing a wide range of stand dynamic trajectories and in some cases reproduced trajectories that the statistical model was incapable of reproducing. Conclusions The model has potential to be used as a benchmarking tool for evaluating statistical and process models and may provide a mechanism to separate signal from noise and improve our ability to analyze and learn from large regional datasets that often have underlying flaws in sample design.

  16. Geometry of behavioral spaces: A computational approach to analysis and understanding of agent based models and agent behaviors

    Science.gov (United States)

    Cenek, Martin; Dahl, Spencer K.

    2016-11-01

    Systems with non-linear dynamics frequently exhibit emergent system behavior, which is important to find and specify rigorously to understand the nature of the modeled phenomena. Through this analysis, it is possible to characterize phenomena such as how systems assemble or dissipate and what behaviors lead to specific final system configurations. Agent Based Modeling (ABM) is one of the modeling techniques used to study the interaction dynamics between a system's agents and its environment. Although the methodology of ABM construction is well understood and practiced, there are no computational, statistically rigorous, comprehensive tools to evaluate an ABM's execution. Often, a human has to observe an ABM's execution in order to analyze how the ABM functions, identify the emergent processes in the agent's behavior, or study a parameter's effect on the system-wide behavior. This paper introduces a new statistically based framework to automatically analyze agents' behavior, identify common system-wide patterns, and record the probability of agents changing their behavior from one pattern of behavior to another. We use network based techniques to analyze the landscape of common behaviors in an ABM's execution. Finally, we test the proposed framework with a series of experiments featuring increasingly emergent behavior. The proposed framework will allow computational comparison of ABM executions, exploration of a model's parameter configuration space, and identification of the behavioral building blocks in a model's dynamics.

  17. Transient or permanent fisheye views

    DEFF Research Database (Denmark)

    Jakobsen, Mikkel Rønne; Hornbæk, Kasper

    2012-01-01

    Transient use of information visualization may support specific tasks without permanently changing the user interface. Transient visualizations provide immediate and transient use of information visualization close to and in the context of the user’s focus of attention. Little is known, however......, about the benefits and limitations of transient visualizations. We describe an experiment that compares the usability of a fisheye view that participants could call up temporarily, a permanent fisheye view, and a linear view: all interfaces gave access to source code in the editor of a widespread...... programming environment. Fourteen participants performed varied tasks involving navigation and understanding of source code. Participants used the three interfaces for between four and six hours in all. Time and accuracy measures were inconclusive, but subjective data showed a preference for the permanent...

  18. Information spreading in Delay Tolerant Networks based on nodes' behaviors

    Science.gov (United States)

    Wu, Yahui; Deng, Su; Huang, Hongbin

    2014-07-01

    Information spreading in DTNs (Delay Tolerant Networks) adopts a store-carry-forward method, and nodes receive the message from others directly. However, it is hard to judge whether the information is safe in this communication mode. In this case, a node may observe other nodes' behaviors. At present, there is no theoretical model to describe the varying rule of the nodes' trusting level. In addition, due to the uncertainty of the connectivity in DTN, a node is hard to get the global state of the network. Therefore, a rational model about the node's trusting level should be a function of the node's own observing result. For example, if a node finds k nodes carrying a message, it may trust the information with probability p(k). This paper does not explore the real distribution of p(k), but instead presents a unifying theoretical framework to evaluate the performance of the information spreading in above case. This framework is an extension of the traditional SI (susceptible-infected) model, and is useful when p(k) conforms to any distribution. Simulations based on both synthetic and real motion traces show the accuracy of the framework. Finally, we explore the impact of the nodes' behaviors based on certain special distributions through numerical results.

  19. Authoritative knowledge, evidence-based medicine, and behavioral pediatrics.

    Science.gov (United States)

    Kennell, J H

    1999-12-01

    Evidence-based medicine is the conscientious and judicious use of current best knowledge in making decisions about the care of individual patients, often from well-designed, randomized, controlled trials. Authoritative medicine is the traditional approach to learning and practicing medicine, but no one authority has comprehensive scientific knowledge. Archie Cochrane proposed that every medical specialty should compile a list of all of the randomized, controlled trials within its field to be available for those who wish to know what treatments are effective. This was done first for obstetrics by a group collecting and critically analyzing all of the randomized trials and then indicating procedures every mother should have and those that no mother should have. Support during labor was used as an example. Similar groups are now active in almost all specialties, with information available on the Internet in the Cochrane Database of Systematic Reviews. Developmental-behavioral pediatrics should be part of this movement to evidence-based medicine.

  20. Indentation creep behaviors of amorphous Cu-based composite alloys

    Science.gov (United States)

    Song, Defeng; Ma, Xiangdong; Qian, Linfang

    2018-04-01

    This work reports the indentation creep behaviors of two Si2Zr3/amorphous Cu-based composite alloys utilizing nanoindentation technique. By analysis with Kelvin model, the retardation spectra of alloys at different positions, detached and attached regions to the intermetallics, were deduced. For the indentation of detached regions to Si2Zr3 intermetallics in both alloys, very similarity in creep displacement can be observed and retardation spectra show a distinct disparity in the second retardation peak. For the indentation of detached regions, the second retardation spectra also display distinct disparity. At both positions, the retardation spectra suggest that Si elements may lead to the relatively dense structure in the amorphous matrix and to form excessive Si2Zr3 intermetallics which may deteriorate the plastic deformation of current Cu-based composite alloys.

  1. Permanent magnets and its production by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Enrique Herraiz Lalana

    2018-06-01

    Full Text Available In this work, the historical relationship between permanent magnets and powder metallurgy is reviewed. Powder metallurgy is a manufacturing technique based on the compaction of powders that are sintered to create a solid product. This technique was used in the production of permanent magnets for the first time in the 18th century and, nowadays, most permanent magnetic materials are manufacturing by this mean. Magnetic properties are highly dependent on the microstructure of the final product, the magnetic alignment of domains and presence of porosity, to mention a few, and powder metallurgy enables fine control of these factors.

  2. Connecting Temporary and Permanent Organizing

    DEFF Research Database (Denmark)

    Stjerne, Iben Sandal; Velikova, Silviya Svejenova

    2016-01-01

    This paper investigates the relationship between a permanent organization and a series of temporary organizations. It draws on an in-depth study of the process through which a Danish film production company, seeking to balance innovation and persistence in a troubled industry, struggles to realize...... a novel children’s film and its sequels. The study reveals tensions at different levels as well as boundary work and boundary roles that address them, bringing in shadows of past and future projects. The study extends the understanding of the dialectic between temporary and permanent organizing...

  3. Children without Permanent Parents: Research, Practice, and Policy

    Science.gov (United States)

    Bakermans-Kranenburg, Marian J.; Bos, Karen; Bunkers, Kelley McCreery; Dobrova-Krol, Natasha A.; Engle, Patrice L.; Fox, Nathan A.; Gamer, Gary N.; Goldman, Philip; Groark, Christina J.; Greenberg, Aaron; Grotevant, Harold D.; Groza, Victor K.; Gunnar, Megan R.; Johnson, Dana E.; Juffer, Femmie; Kreppner, Jana M.; Le Mare, Lucy; McCall, Robert B.; Muhamedrahimov, Rifkat J.; Nelson, Charles A., III; Palacios, Jesus; Sonuga-Barke, Edmund J. S.; Steele, Howard; Steele, Miriam; Tieman, Wendy; van IJzendoorn, Marinus H.; Verhulst, Frank C.; Vorria, Panayiota; Zeanah, Charles H.

    2011-01-01

    This monograph reviews literature pertaining to children without permanent parents. Chapters review (1) the development of children while institutional residents; (2) the development of postinstitutionalized children transitioned to family environments (i.e., adoption); the effects of institutionalization on (3) attachment behaviors, (4) physical…

  4. Identifying and Assessing Community-Based Social Behavior of Adolescents and Young Adults with EBD.

    Science.gov (United States)

    Bullis, Michael; And Others

    1994-01-01

    A battery of three measures for assessing the community-based social behavior of adolescents and young adults with emotional and behavioral disorders is described. The measures, in male and female forms, are "Test of Community-Based Social Skill Knowledge,""Scale of Community-Based Social Skill Performance," and "Behaviors That Are Undesirable for…

  5. Evidence-Based School Behavior Assessment of Externalizing Behavior in Young Children.

    Science.gov (United States)

    Bagner, Daniel M; Boggs, Stephen R; Eyberg, Sheila M

    2010-02-01

    This study examined the psychometric properties of the Revised Edition of the School Observation Coding System (REDSOCS). Participants were 68 children ages 3 to 6 who completed parent-child interaction therapy for Oppositional Defiant Disorder as part of a larger efficacy trial. Interobserver reliability on REDSOCS categories was moderate to high, with percent agreement ranging from 47% to 90% (M = 67%) and Cohen's kappa coefficients ranging from .69 to .95 (M = .82). Convergent validity of the REDSOCS categories was supported by significant correlations with the Intensity Scale of the Sutter-Eyberg Student Behavior Inventory-Revised and related subscales of the Conners' Teacher Rating Scale-Revised: Long Version (CTRS-R: L). Divergent validity was indicated by nonsignificant correlations between REDSOCS categories and scales on the CTRS-R: L expected not to relate to disruptive classroom behavior. Treatment sensitivity was demonstrated for two of the three primary REDSOCS categories by significant pre to posttreatment changes. This study provides psychometric support for the designation of REDSOCS as an evidence-based assessment procedure for young children.

  6. Team-based assessment of professional behavior in medical students.

    Science.gov (United States)

    Raee, Hojat; Amini, Mitra; Momen Nasab, Ameneh; Malek Pour, Abdolrasoul; Jafari, Mohammad Morad

    2014-07-01

    Self and peer assessment provides important information about the individual's performance and behavior in all aspects of their professional environment work. The aim of this study is to evaluate the professional behavior and performance in medical students in the form of team based assessment. In a cross-sectional study, 100 medical students in the 7(th) year of education were randomly selected and enrolled; for each student five questionnaires were filled out, including one self-assessment, two peer assessments and two residents assessment. The scoring system of the questionnaires was based on seven point Likert scale.  After filling out the questions in the questionnaire, numerical data and written comments provided to the students were collected, analyzed and discussed. Internal consistency (Cronbach's alpha) of the questionnaires was assessed. A p<0.05 was considered as significant level. Internal consistency was acceptable (Cronbach's alpha 0.83). Interviews revealed that the majority of students and assessors interviewed found the method acceptable. The range of scores was 1-6 (Mean±SD=4.39±0.57) for the residents' assessment, 2-6 (Mean±SD= 4.49±0.53) for peer assessment, and 3-7 (Mean±SD=5.04±0.32) for self-assessment. There was a significant difference between self assessment and other methods of assessment. This study demonstrates that a team-based assessment is an acceptable and feasible method for peer and self-assessment of medical students' learning in a clinical clerkship, and has some advantages over traditional assessment methods. Further studies are needed to focus on the strengths and weaknesses.

  7. Team-based assessment of professional behavior in medical students

    Directory of Open Access Journals (Sweden)

    HOJAT RAEE

    2004-07-01

    Full Text Available Introducrion: Self and peer assessment provides important information about the individual’s performance and behavior in all aspects of their professional environment work. The aim of this study is to evaluate the professional behavior and performance in medical students in the form of team based assessment. Methods: In a cross-sectional study, 100 medical students in the 7th year of education were randomly selected and enrolled; for each student five questionnaires were filled out, including one self-assessment, two peer assessments and two residents assessment. The scoring system of the questionnaires was based on seven point Likert scale. After filling out the questions in the questionnaire, numerical data and written comments provided to the students were collected, analyzed and discussed. Internal consistency (Cronbach’s alpha of the questionnaires was assessed. A p<0.05 was considered as significant. Results: Internal consistency was acceptable (Cronbach’s alpha 0.83. Interviews revealed that the majority of students and assessors interviewed found the method acceptable. The range of scores was 1-6 (Mean±SD=4.39±0.57 for the residents' assessment, 2-6 (Mean±SD=4.49±0.53 for peer assessment, and 3-7 (Mean±SD=5.04±0.32 for self-assessment. There was a significant difference between self assessment and other methods of assessment. Conclusions: This study demonstrates that a team-based assessment is an acceptable and feasible method for peer and self-assessment of medical students’ learning in a clinical clerkship, and has some advantages over traditional assessment methods. Further studies are needed to focus on the strengths and weaknesses.

  8. OAS :: Member States : Permanent Representatives

    Science.gov (United States)

    Rights Actions against Corruption C Children Civil Registry Civil Society Contact Us Culture Cyber Barbados Belize Bolivia Brazil Canada Chile Colombia Costa Rica Cuba 1 Dominica (Commonwealth of) Dominican Gutierez Ambassador, Permanent Representative of Belize Diego Pary Rodríguez Bolivia Diego Pary Rodríguez

  9. Teacher Implementation of Trial-Based Functional Analysis and Differential Reinforcement of Alternative Behavior for Students with Challenging Behavior

    Science.gov (United States)

    Flynn, Susan D.; Lo, Ya-yu

    2016-01-01

    The purpose of this study was to examine the effects of a training package on three middle school special education teachers' accurate implementation of trial-based functional analysis (TBFA) and differential reinforcement of alternative behavior (DRA) with their students with autism spectrum disorders or emotional and behavioral disorders in the…

  10. Using Stimulus Equivalence-Based Instruction to Teach Graduate Students in Applied Behavior Analysis to Interpret Operant Functions of Behavior

    Science.gov (United States)

    Albright, Leif; Schnell, Lauren; Reeve, Kenneth F.; Sidener, Tina M.

    2016-01-01

    Stimulus equivalence-based instruction (EBI) was used to teach four, 4-member classes representing functions of behavior to ten graduate students. The classes represented behavior maintained by attention (Class 1), escape (Class 2), access to tangibles (Class 3), and automatic reinforcement (Class 4). Stimuli within each class consisted of a…

  11. Experimental oligopolies modeling: A dynamic approach based on heterogeneous behaviors

    Science.gov (United States)

    Cerboni Baiardi, Lorenzo; Naimzada, Ahmad K.

    2018-05-01

    In the rank of behavioral rules, imitation-based heuristics has received special attention in economics (see [14] and [12]). In particular, imitative behavior is considered in order to understand the evidences arising in experimental oligopolies which reveal that the Cournot-Nash equilibrium does not emerge as unique outcome and show that an important component of the production at the competitive level is observed (see e.g.[1,3,9] or [7,10]). By considering the pioneering groundbreaking approach of [2], we build a dynamical model of linear oligopolies where heterogeneous decision mechanisms of players are made explicit. In particular, we consider two different types of quantity setting players characterized by different decision mechanisms that coexist and operate simultaneously: agents that adaptively adjust their choices towards the direction that increases their profit are embedded with imitator agents. The latter ones use a particular form of proportional imitation rule that considers the awareness about the presence of strategic interactions. It is noteworthy that the Cournot-Nash outcome is a stationary state of our models. Our thesis is that the chaotic dynamics arousing from a dynamical model, where heterogeneous players are considered, are capable to qualitatively reproduce the outcomes of experimental oligopolies.

  12. Permanent magnet quadrupoles for the CLIC Drive Beam decelerator

    CERN Document Server

    Shepherd, Ben; Collomb, Norbert

    2012-01-01

    STFC in collaboration with CERN has developed a new type of adjustable permanent magnet based quadrupole for the CLIC Drive Beam Decelerator. It uses vertical movement of the permanent magnets to achieve an integrated gradient range of 3.6-14.6T, which will allow it to be used for the first 60% of the decelerator line. Construction of a prototype of this magnet has begun; following this, it will be measured magnetically at CERN and Daresbury Laboratory.

  13. PENGUKURAN PERMANENT EARNINGS PADA HUBUNGAN DENGAN KEBIJAKAN DIVIDEND PERUSAHAAN : REVIEW PENELITIAN

    Directory of Open Access Journals (Sweden)

    Wahyu Manuhara Putra

    2016-02-01

    Full Text Available Corporate earnings divided into a permanent component of earnings and transitory earnings will be very useful in estimating the future value of the company, that will be useful in decision making stock return. Be more relevant for investors and financial analysts in analyzing the earnings based on the permanent and transitory earnings. On permanent earnings will be more focused to get the gain from investments. One focus of research is based on this component is to test the relationship with the earnings dividend payment policy. Based on several studies obtained different results concerning the relationship with the permanent earnings dividend policy. Research that focuses on permanent earnings using two approaches to determine the accuracy of the proxy of permanent earnings. Determination of permanent earnings through the stock price and the latter by using the accounting profit.

  14. Faculty Members' Ethical Behaviors: "A Survey Based on Students' Perceptions at Universities in Turkey"

    Science.gov (United States)

    Ozcan, Kenan; Balyer, Aydin; Servi, Tayfun

    2013-01-01

    As members of academic team, faculty behaviors have vital influence on students' lives at universities. This study purposes to discover students' perceptions about faculty behaviors concerning their professional responsibilities, dating/sexual harassment, behaviors inside and behaviors outside the classroom and relationship based on self-interest.…

  15. Nitriding behavior of Ni and Ni-based binary alloys

    Energy Technology Data Exchange (ETDEWEB)

    Fonovic, Matej

    2015-01-15

    Gaseous nitriding is a prominent thermochemical surface treatment process which can improve various properties of metallic materials such as mechanical, tribological and/or corrosion properties. This process is predominantly performed by applying NH{sub 3}+H{sub 2} containing gas atmospheres serving as the nitrogen donating medium at temperatures between 673 K and 873 K (400 C and 600 C). NH{sub 3} decomposes at the surface of the metallic specimen and nitrogen diffuses into the surface adjacent region of the specimen whereas hydrogen remains in the gas atmosphere. One of the most important parameters characterizing a gaseous nitriding process is the so-called nitriding potential (r{sub N}) which determines the chemical potential of nitrogen provided by the gas phase. The nitriding potential is defined as r{sub N} = p{sub NH{sub 3}}/p{sub H{sub 2}{sup 3/2}} where p{sub NH{sub 3}} and p{sub H{sub 2}} are the partial pressures of the NH{sub 3} and H{sub 2} in the nitriding atmosphere. In contrast with nitriding of α-Fe where the nitriding potential is usually in the range between 0.01 and 1 atm{sup -1/2}, nitriding of Ni and Ni-based alloys requires employing nitriding potentials higher than 100 atm{sup -1/2} and even up to ∞ (nitriding in pure NH{sub 3} atmosphere). This behavior is compatible with decreased thermodynamic stability of the 3d-metal nitrides with increasing atomic number. Depending on the nitriding conditions (temperature, nitriding potential and treatment time), different phases are formed at the surface of the Ni-based alloys. By applying very high nitriding potential, formation of hexagonal Ni{sub 3}N at the surface of the specimen (known as external nitriding) leads to the development of a compound layer, which may improve tribological properties. Underneath the Ni{sub 3}N compound layer, two possibilities exist: (i) alloying element precipitation within the nitrided zone (known as internal nitriding) and/or (ii) development of metastable and

  16. A Behavior-Based Circuit Model of How Outcome Expectations Organize Learned Behavior in Larval "Drosophila"

    Science.gov (United States)

    Schleyer, Michael; Saumweber, Timo; Nahrendorf, Wiebke; Fischer, Benjamin; von Alpen, Desiree; Pauls, Dennis; Thum, Andreas; Gerber, Bertram

    2011-01-01

    Drosophila larvae combine a numerically simple brain, a correspondingly moderate behavioral complexity, and the availability of a rich toolbox for transgenic manipulation. This makes them attractive as a study case when trying to achieve a circuit-level understanding of behavior organization. From a series of behavioral experiments, we suggest a…

  17. Can aviation-based team training elicit sustainable behavioral change?

    Science.gov (United States)

    Sax, Harry C; Browne, Patrick; Mayewski, Raymond J; Panzer, Robert J; Hittner, Kathleen C; Burke, Rebecca L; Coletta, Sandra

    2009-12-01

    To quantify effects of aviation-based crew resource management training on patient safety-related behaviors and perceived personal empowerment. Prospective study of checklist use, error self-reporting, and a 10-point safety empowerment survey after participation in a crew resource management training intervention. Seven hundred twenty-two-bed university hospital; 247-bed affiliated community hospital. There were 857 participants, the majority of whom were nurses (50%), followed by ancillary personnel (28%) and physicians (22%). Preoperative checklist use over time; number and type of entries on a Web-based incident reporting system; and measurement of degree of empowerment (1-5 scale) on a 10-point survey of safety attitudes and actions given prior to, immediately after, and a minimum of 2 months after training. Since 2003, 10 courses trained 857 participants in multiple disciplines. Preoperative checklist use rose (75% in 2003, 86% in 2004, 94% in 2005, 98% in 2006, and 100% in 2007). Self-initiated reports increased from 709 per quarter in 2002 to 1481 per quarter in 2008. The percentage of reports related to environment as opposed to actual events increased from 15.9% prior to training to 20.3% subsequently (P culture of safety, rose by an average of 0.5 point in all 10 realms immediately posttraining (mean [SD] rating, 3.0 [0.07] vs 3.5 [0.05]; P .05). Crew resource management programs can influence personal behaviors and empowerment. Effects may take years to be ingrained into the culture.

  18. Radioecological sensitivity of permanent grasslands

    International Nuclear Information System (INIS)

    Besson, Benoit

    2009-01-01

    The project 'SENSIB' of the Institute for Radiological Protection and Nuclear Safety (IRSN) aims at characterizing and classifying parameters with significant impact on the transfer of radioactive contaminants in the environment. This thesis is focused on permanent grassland areas. Its objectives are the analysis of the activity variations of two artificial radionuclides ( 137 Cs and 90 Sr) in the chain from soil to dairy products as well as the categorization of ecological and anthropogenic parameters, which determine the sensitivity of the studied area. For this study, in situ sampling is carried out in 15 farms in 3 different French regions (Charente, Puy-de-Dome and Jura). The sampling sites are chosen according to their natural variations (geology, altitude and climate) and the soil types. Additionally to the radiologic measurements, geographic, soil and vegetation data as well as data concerning cattle-rearing and cheese manufacturing processes are gathered. From the soil to the grass vegetation, 137 Cs transfer factors vary between 3 x 10-3 and 148 x 10-3 Bq kg-1 (dry weight) per Bq kg-1 (dry weight) (N = 73). Theses transfer factors are significantly higher in the Puy-de-Dome region than in the Jura region. The 137 Cs transfer factor from cattle feed to milk varies from 5.9 x 10-3 to 258 x 10-3 Bq kg-1 (fresh weight) per Bq kg-1 (dry weight) (N = 28). Statistically, it is higher in the Charente region. Finally, the 90 Sr transfer factor from milk to cheese ranges from 3.9 to 12.1. The studied site with the highest factor is the Jura (N = 25). The link between milk and dairy products is the stage with the most 137 Cs and 90 Sr transfers. A nonlinear approach based on a discretization method of the transfer factor with multiple comparison tests admits a classification of the sensitivity factors from soil to grass vegetation. We can determine 20 factors interfering in the 137 Cs transfer into the vegetation, for instance, the clay rate of the soils or a marker

  19. Intervention Strategies Based on Information-Motivation-Behavioral Skills Model for Health Behavior Change: A Systematic Review

    Directory of Open Access Journals (Sweden)

    Sun Ju Chang, RN, PhD

    2014-09-01

    Conclusion: This review indicates the potential strength of the IMB model as a theoretical framework to develop behavioral interventions. The specific integration strategies delineated for each construct of the model can be utilized to design model-based interventions.

  20. The eHealth Behavior Management Model: a stage-based approach to behavior change and management.

    Science.gov (United States)

    Bensley, Robert J; Mercer, Nelda; Brusk, John J; Underhile, Ric; Rivas, Jason; Anderson, Judith; Kelleher, Deanne; Lupella, Melissa; de Jager, André C

    2004-10-01

    Although the Internet has become an important avenue for disseminating health information, theory-driven strategies for aiding individuals in changing or managing health behaviors are lacking. The eHealth Behavior Management Model combines the Transtheoretical Model, the behavioral intent aspect of the Theory of Planned Behavior, and persuasive communication to assist individuals in negotiating the Web toward stage-specific information. It is here - at the point of stage-specific information - that behavioral intent in moving toward more active stages of change occurs. The eHealth Behavior Management Model is applied in three demonstration projects that focus on behavior management issues: parent-child nutrition education among participants in the U.S. Department of Agriculture Special Supplemental Nutrition Program for Women, Infants and Children; asthma management among university staff and students; and human immunodeficiency virus prevention among South African women. Preliminary results have found the eHealth Behavior Management Model to be promising as a model for Internet-based behavior change programming. Further application and evaluation among other behavior and disease management issues are needed.

  1. Forgetting Bad Behavior: Memory Management for Case-Based Navigation

    National Research Council Canada - National Science Library

    Kira, Zsolt; Arkin, Ronald C

    2006-01-01

    ...) system applied to autonomous robot navigation. This extends previous work that involved a CBR architecture that indexes cases by the spatio-temporal characteristics of the sensor data, and outputs or selects parameters of behaviors in a behavior...

  2. Controlling chaos in the permanent magnet synchronous motor

    International Nuclear Information System (INIS)

    Zribi, Mohamed; Oteafy, Ahmed; Smaoui, Nejib

    2009-01-01

    The Permanent Magnet Synchronous Motor (PMSM) is known to exhibit chaotic behavior under certain conditions. This paper proposes to use an instantaneous Lyapunov exponent control algorithm to control the PMSM. One of the objectives of the control approach is to bring order to the PMSM and to drive it to any user-defined desired state. Simulation results under different operating conditions indicate that the proposed control scheme works well. Moreover, the proposed Lyapunov exponent control scheme is able to induce chaos on the permanent magnet synchronous motor. Simulation results show the effectiveness of the proposed control scheme in chaotifing the response of the motor.

  3. Behavior Assessment in Children Following Hospital-Based General Anesthesia versus Office-Based General Anesthesia

    Directory of Open Access Journals (Sweden)

    LaQuia A. Vinson

    2016-08-01

    Full Text Available The purpose of this study was to determine if differences in behavior exist following dental treatment under hospital-based general anesthesia (HBGA or office-based general anesthesia (OBGA in the percentage of patients exhibiting positive behavior and in the mean Frankl scores at recall visits. This retrospective study examined records of a pediatric dental office over a 4 year period. Patients presenting before 48 months of age for an initial exam who were diagnosed with early childhood caries were included in the study. Following an initial exam, patients were treated under HBGA or OBGA. Patients were followed to determine their behavior at 6-, 12- and 18-month recall appointments. Fifty-four patients received treatment under HBGA and 26 were treated under OBGA. OBGA patients were significantly more likely to exhibit positive behavior at the 6- and 12-month recall visits p = 0.038 & p = 0.029. Clinicians should consider future behavior when determining general anesthesia treatment modalities in children with early childhood caries presenting to their office.

  4. Fast Food Consumption Behaviors in High-School Students based on the Theory of Planned Behavior (TPB)

    OpenAIRE

    Kamal Mirkarimi; Morteza Mansourian; Mohammad Javad Kabir; Rahman Berdi Ozouni- Davaji; Maryam Eri; Seyed Ghadir Hosseini; Mostafa Qorbani; Omid Safari; Babak Rastgari Mehr; Mehdi Noroozi; Abdurrahman Charkazi; Hossein Shahnazi

    2016-01-01

    Background: Studies report inappropriate snack and junk food consumption patterns in children and young adults in Iran. The current survey was aimed to explore fast food consumption behaviors in high-school students based on the Theory of Planned Behavior. Materials and Methods: A cross-sectional study was done among 500 high-school students. Samples were selected based on cluster sampling method at first and simple random at second. Data were collected using a researcher-made questionnaire. ...

  5. Comparing superconducting and permanent magnets for magnetic refrigeration

    DEFF Research Database (Denmark)

    Bjørk, Rasmus; Nielsen, Kaspar Kirstein; Bahl, C. R. H.

    2016-01-01

    We compare the cost of a high temperature superconducting (SC) tape-based solenoidwith a permanent magnet (PM) Halbach cylinder for magnetic refrigeration.Assuming a five liter active magnetic regenerator volume, the price of each type ofmagnet is determined as a function of aspect ratio...... of the regenerator and desiredinternal magnetic field. It is shown that to produce a 1 T internal field in theregenerator a permanent magnet of hundreds of kilograms is needed or an area ofsuperconducting tape of tens of square meters. The cost of cooling the SC solenoidis shown to be a small fraction of the cost...... of the SC tape. Assuming a cost ofthe SC tape of 6000 $/m2 and a price of the permanent magnet of 100 $/kg, thesuperconducting solenoid is shown to be a factor of 0.3-3 times more expensive thanthe permanent magnet, for a desired field from 0.5-1.75 T and the geometrical aspectratio of the regenerator...

  6. Overview on the permanent magnets technology of rare earth based on Nd-Fe-B; Panorama general sobre tecnologia de imanes permanentes de tierras raras a base de Nd-Fe-B

    Energy Technology Data Exchange (ETDEWEB)

    Rosales Vazquez, Maria Ines [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1990-12-31

    In this paper the technological development in the area of permanent magnetic materials, is shown, from the 1930`s when the first aluminum-nickel-cobalt (Al-Ni-Co) magnets appeared. As a result of the continuous worldwide research in this field, it was made known, during the 1980`s decade of a new type of magnets based on Neodymium (Nd). In accordance with the outstanding magnetic properties of these magnets, at the Instituto de Investigaciones Electricas (IIE), their development was initiated, focussed on the stages and parameters definition of their manufacturing process. Up to now, the research has been oriented to the preparation of magnets of the isotropic agglutinated type and the manufacturing process encompasses the following stages: a) Alloy preparation; b) Microcrystals obtainment; c) Magnet preparation. The preliminary results that have been obtained in the magnetic characterization show that the quality of the prepared magnets is comparable to the quality of the imported magnets and/or to the ones other research groups report. [Espanol] En este trabajo se muestra el desarrollo tecnologico del area de materiales magneticos permanentes a partir de los anos treinta en que surgieron los primeros imanes de aluminio-niquel-cobalto (Al-Ni-Co). Como resultado de la constante investigacion a nivel mundial en ese campo, durante el decenio de los ochenta se informo en torno a un nuevo tipo de imanes a base de neodimio (Nd). Atendiendo a las propiedades magneticas sobresalientes de estos imanes, en el Instituto de Investigaciones Electricas (IIE), se inicio el desarrollo de los mismos, enfocandolo a la definicion de las etapas y parametros del proceso de fabricacion. Hasta ahora, la investigacion se ha orientado a la preparacion de imanes de tipo isotropico aglutinado y el proceso de fabricacion comprende las etapas: a) preparacion de la aleacion; b) obtencion de microcristales, y c) preparacion de los imanes. Los resultados preliminares que se han obtenido en la

  7. Overview on the permanent magnets technology of rare earth based on Nd-Fe-B; Panorama general sobre tecnologia de imanes permanentes de tierras raras a base de Nd-Fe-B

    Energy Technology Data Exchange (ETDEWEB)

    Rosales Vazquez, Maria Ines [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1991-12-31

    In this paper the technological development in the area of permanent magnetic materials, is shown, from the 1930`s when the first aluminum-nickel-cobalt (Al-Ni-Co) magnets appeared. As a result of the continuous worldwide research in this field, it was made known, during the 1980`s decade of a new type of magnets based on Neodymium (Nd). In accordance with the outstanding magnetic properties of these magnets, at the Instituto de Investigaciones Electricas (IIE), their development was initiated, focussed on the stages and parameters definition of their manufacturing process. Up to now, the research has been oriented to the preparation of magnets of the isotropic agglutinated type and the manufacturing process encompasses the following stages: a) Alloy preparation; b) Microcrystals obtainment; c) Magnet preparation. The preliminary results that have been obtained in the magnetic characterization show that the quality of the prepared magnets is comparable to the quality of the imported magnets and/or to the ones other research groups report. [Espanol] En este trabajo se muestra el desarrollo tecnologico del area de materiales magneticos permanentes a partir de los anos treinta en que surgieron los primeros imanes de aluminio-niquel-cobalto (Al-Ni-Co). Como resultado de la constante investigacion a nivel mundial en ese campo, durante el decenio de los ochenta se informo en torno a un nuevo tipo de imanes a base de neodimio (Nd). Atendiendo a las propiedades magneticas sobresalientes de estos imanes, en el Instituto de Investigaciones Electricas (IIE), se inicio el desarrollo de los mismos, enfocandolo a la definicion de las etapas y parametros del proceso de fabricacion. Hasta ahora, la investigacion se ha orientado a la preparacion de imanes de tipo isotropico aglutinado y el proceso de fabricacion comprende las etapas: a) preparacion de la aleacion; b) obtencion de microcristales, y c) preparacion de los imanes. Los resultados preliminares que se han obtenido en la

  8. Individual Travel Behavior Modeling of Public Transport Passenger Based on Graph Construction

    OpenAIRE

    Quan Liang; Jiancheng Weng; Wei Zhou; Selene Baez Santamaria; Jianming Ma; Jian Rong

    2018-01-01

    This paper presents a novel method for mining the individual travel behavior regularity of different public transport passengers through constructing travel behavior graph based model. The individual travel behavior graph is developed to represent spatial positions, time distributions, and travel routes and further forecasts the public transport passenger’s behavior choice. The proposed travel behavior graph is composed of macronodes, arcs, and transfer probability. Each macronode corresponds...

  9. Microstructures and oxidation behavior of some Molybdenum based alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ray, Pratik Kumar [Iowa State Univ., Ames, IA (United States)

    2011-01-01

    The advent of Ni based superalloys revolutionized the high temperature alloy industry. These materials are capable of operating in extremely harsh environments, comprising of temperatures around 1050 C, under oxidative conditions. Demands for increased fuel efficiency, however, has highlighted the need for materials that can be used under oxidative conditions at temperatures in excess of 1200 C. The Ni based superalloys are restricted to lower temperatures due to the presence of a number of low melting phases that melt in the 1250 - 1450 C, resulting in softening of the alloys above 1000 C. Therefore, recent research directions have been skewed towards exploring and developing newer alloy systems. This thesis comprises a part of such an effort. Techniques for rapid thermodynamic assessments were developed and applied to two different systems - Mo-Si alloys with transition metal substitutions (and this forms the first part of the thesis) and Ni-Al alloys with added components for providing high temperature strength and ductility. A hierarchical approach towards alloy design indicated the Mo-Ni-Al system as a prospective candidate for high temperature applications. Investigations on microstructures and oxidation behavior, under both isothermal and cyclic conditions, of these alloys constitute the second part of this thesis. It was seen that refractory metal systems show a marked microstructure dependence of oxidation.

  10. Automated phenotyping of permanent crops

    Science.gov (United States)

    McPeek, K. Thomas; Steddom, Karl; Zamudio, Joseph; Pant, Paras; Mullenbach, Tyler

    2017-05-01

    AGERpoint is defining a new technology space for the growers' industry by introducing novel applications for sensor technology and data analysis to growers of permanent crops. Serving data to a state-of-the-art analytics engine from a cutting edge sensor platform, a new paradigm in precision agriculture is being developed that allows growers to understand the unique needs of each tree, bush or vine in their operation. Autonomous aerial and terrestrial vehicles equipped with multiple varieties of remote sensing technologies give AGERpoint the ability to measure key morphological and spectral features of permanent crops. This work demonstrates how such phenotypic measurements combined with machine learning algorithms can be used to determine the variety of crops (e.g., almond and pecan trees). This phenotypic and varietal information represents the first step in enabling growers with the ability to tailor their management practices to individual plants and maximize their economic productivity.

  11. Friction behavior of cobalt base and nickel base hardfacing materials in high temperature sodium

    International Nuclear Information System (INIS)

    Mizobuchi, Syotaro; Kano, Shigeki; Nakayama, Kohichi; Atsumo, Hideo

    1980-01-01

    A friction behavior of the hardfacing materials such as cobalt base alloy ''Stellite'' and nickel base alloy ''Colmonoy'' used in the sliding components of a sodium cooled fast breeder reactor was investigated in various sodium environments. Also, friction tests on these materials were carried out in argon environment. And they were compared with those in sodium environment. The results obtained are as follows: (1) In argon, the cobalt base hardfacing alloy showed better friction behavior than the nickel base hardfacing alloy. In sodium, the latter was observed to have the better friction behavior being independent of the sodium temperature. (2) The friction coefficient of each material tends to become lower by pre-exposure in sodium. Particularly, this tendency was remarkable for the nickel base hardfacing alloy. (3) The friction coefficient between SUS 316 and one of these hardfacing materials was higher than that between latter materials. Also, some elements of hardfacing alloys were recognized to transfer on the friction surface of SUS 316 material. (4) It was observed that each tested material has a greater friction coefficient with a decrease of the oxygen content in sodium. (author)

  12. A neural substrate for object permanence in monkey inferotemporal cortex.

    Science.gov (United States)

    Puneeth, N C; Arun, S P

    2016-08-03

    We take it for granted that objects continue to exist after being occluded. This knowledge - known as object permanence - is present even in childhood, but its neural basis is not fully understood. Here, we show that monkey inferior temporal (IT) neurons carry potential signals of object permanence even in animals that received no explicit behavioral training. We compared two conditions with identical visual stimulation: the same object emerged from behind an occluder as expected following its occlusion, or unexpectedly after occlusion of a different object. Some neurons produced a larger (surprise) signal when the object emerged unexpectedly, whereas other neurons produced a larger (match) signal when the object reappeared as expected. Neurons carrying match signals also reinstated selective delay period activity just before the object emerged. Thus, signals related to object permanence are present in IT neurons and may arise through an interplay of memory and match computations.

  13. Tunable high-gradient permanent magnet quadrupoles

    CERN Document Server

    Shepherd, B J A; Marks, N; Collomb, N A; Stokes, D G; Modena, M; Struik, M; Bartalesi, A

    2014-01-01

    A novel type of highly tunable permanent magnet (PM) based quadrupole has been designed by the ZEPTO collaboration. A prototype of the design (ZEPTO-Q1), intended to match the specification for the CLIC Drive Beam Decelerator, was built and magnetically measured at Daresbury Laboratory and CERN. The prototype utilises two pairs of PMs which move in opposite directions along a single vertical axis to produce a quadrupole gradient variable between 15 and 60 T/m. The prototype meets CLIC's challenging specification in terms of the strength and tunability of the magnet.

  14. Behavior-based network management: a unique model-based approach to implementing cyber superiority

    Science.gov (United States)

    Seng, Jocelyn M.

    2016-05-01

    Behavior-Based Network Management (BBNM) is a technological and strategic approach to mastering the identification and assessment of network behavior, whether human-driven or machine-generated. Recognizing that all five U.S. Air Force (USAF) mission areas rely on the cyber domain to support, enhance and execute their tasks, BBNM is designed to elevate awareness and improve the ability to better understand the degree of reliance placed upon a digital capability and the operational risk.2 Thus, the objective of BBNM is to provide a holistic view of the digital battle space to better assess the effects of security, monitoring, provisioning, utilization management, allocation to support mission sustainment and change control. Leveraging advances in conceptual modeling made possible by a novel advancement in software design and implementation known as Vector Relational Data Modeling (VRDM™), the BBNM approach entails creating a network simulation in which meaning can be inferred and used to manage network behavior according to policy, such as quickly detecting and countering malicious behavior. Initial research configurations have yielded executable BBNM models as combinations of conceptualized behavior within a network management simulation that includes only concepts of threats and definitions of "good" behavior. A proof of concept assessment called "Lab Rat," was designed to demonstrate the simplicity of network modeling and the ability to perform adaptation. The model was tested on real world threat data and demonstrated adaptive and inferential learning behavior. Preliminary results indicate this is a viable approach towards achieving cyber superiority in today's volatile, uncertain, complex and ambiguous (VUCA) environment.

  15. Permanency analysis on human electroencephalogram signals for pervasive Brain-Computer Interface systems.

    Science.gov (United States)

    Sadeghi, Koosha; Junghyo Lee; Banerjee, Ayan; Sohankar, Javad; Gupta, Sandeep K S

    2017-07-01

    Brain-Computer Interface (BCI) systems use some permanent features of brain signals to recognize their corresponding cognitive states with high accuracy. However, these features are not perfectly permanent, and BCI system should be continuously trained over time, which is tedious and time consuming. Thus, analyzing the permanency of signal features is essential in determining how often to repeat training. In this paper, we monitor electroencephalogram (EEG) signals, and analyze their behavior through continuous and relatively long period of time. In our experiment, we record EEG signals corresponding to rest state (eyes open and closed) from one subject everyday, for three and a half months. The results show that signal features such as auto-regression coefficients remain permanent through time, while others such as power spectral density specifically in 5-7 Hz frequency band are not permanent. In addition, eyes open EEG data shows more permanency than eyes closed data.

  16. In vitro and in vivo ocular safety and eye surface permanence determination by direct and Magnetic Resonance Imaging of ion-sensitive hydrogels based on gellan gum and kappa-carrageenan.

    Science.gov (United States)

    Fernández-Ferreiro, Anxo; González Barcia, Miguel; Gil-Martínez, María; Vieites-Prado, Alba; Lema, Isabel; Argibay, Barbara; Blanco Méndez, José; Lamas, Maria Jesus; Otero-Espinar, Francisco Javier

    2015-08-01

    Gellan gum, kappa-carrageenan and alginates are natural polysaccharides able to interact with different cations that can be used to elaborate ion-activated in situ gelling systems for different uses. The interaction between fluid solutions of these polysaccharides and cations presents into the tear made these biopolymers very interesting to elaborate ophthalmic drug delivery systems. The main purpose of this study is to evaluate the ability of mixtures of these polymers to obtain ion-activated ophthalmic in situ gelling systems with optimal properties for ocular use. To achieve this purpose different proportion of the biopolymers were analyzed using a mixture experimental design evaluating their transparency, mechanical properties and bioadhesion in the absence and presence of simulated tear fluid. Tear induces a rapid sol-to-gel phase transition in the mixtures forming a consistent hydrogel. The solution composed by 80% of gellan gum and 20% kappa-carrageenan showed the best mechanical and mucoadhesive properties. This mixture was evaluated for rheological behavior, microstructure, cytotoxicity, acute corneal irritancy, ex-vivo and in vivo ocular toxicity and in vivo corneal contact time using Magnetic Resonance Images (MRI) techniques. Result indicates that the system is safe at ophthalmic level and produces an extensive ocular permanence higher than 6h. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Lawful Permanent Residents Fiscal Year 2011 Country

    Data.gov (United States)

    Department of Homeland Security — Lawful permanet residents (LPRs) are foreign nationals who have been gratned the right to reside permanently in the United States. LPRs are also known as 'permanent...

  18. Behavioral Intention to Use Public Transport Based on Theory of Planned Behavior

    Directory of Open Access Journals (Sweden)

    Ambak Kamarudin

    2016-01-01

    Full Text Available An increase in population generates increasing in travel demand. In Malaysia, public transport become an important modes of transport that connection people. This paper presents behavioural intention to use public transport especially public bus based on Theory of Planned Behaviour (TPB. A questionnaire survey was conducted to identify factors that contribute and influence users to use public bus and to determine factor that most dominant using TPB model. A total of 282 questionnaires were distributed in selected area of Batu Pahat and Kluang. Correlation and regression analysis were used for this study. Results show that the Attitude toward public transport is the most dominant factor compared with Subjective Norm and Perceived Behavior Control that influencing users to use public bus. Majority respondents were agreed that they prefer to use public bus because it is cheap to travel and no other choices of other transfer modes. As for the recommendation, this study can be extended in future as part of strategic sustainable transportation system in Batu Pahat and Kluang areas.

  19. Teaching Object Permanence: An Action Research Study

    Science.gov (United States)

    Bruce, Susan M.; Vargas, Claudia

    2013-01-01

    "Object permanence," also known as "object concept" in the field of visual impairment, is one of the most important early developmental milestones. The achievement of object permanence is associated with the onset of representational thought and language. Object permanence is important to orientation, including the recognition of landmarks.…

  20. 21 CFR 886.4445 - Permanent magnet.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Permanent magnet. 886.4445 Section 886.4445 Food... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4445 Permanent magnet. (a) Identification. A permanent magnet is a nonelectric device that generates a magnetic field intended to find and remove metallic...

  1. The effect of abstract versus concrete framing on judgments of biological and psychological bases of behavior.

    Science.gov (United States)

    Kim, Nancy S; Johnson, Samuel G B; Ahn, Woo-Kyoung; Knobe, Joshua

    2017-01-01

    Human behavior is frequently described both in abstract, general terms and in concrete, specific terms. We asked whether these two ways of framing equivalent behaviors shift the inferences people make about the biological and psychological bases of those behaviors. In five experiments, we manipulated whether behaviors are presented concretely (i.e. with reference to a specific person, instantiated in the particular context of that person's life) or abstractly (i.e. with reference to a category of people or behaviors across generalized contexts). People judged concretely framed behaviors to be less biologically based and, on some dimensions, more psychologically based than the same behaviors framed in the abstract. These findings held true for both mental disorders (Experiments 1 and 2) and everyday behaviors (Experiments 4 and 5), and yielded downstream consequences for the perceived efficacy of disorder treatments (Experiment 3). Implications for science educators, students of science, and members of the lay public are discussed.

  2. Optimal Scheduling of Doctors Outpatient Departments Based on Patients’ Behavior

    Directory of Open Access Journals (Sweden)

    Zongwei Ren

    2016-01-01

    Full Text Available The low operational efficiency in the field of medical and health care has become a serious problem in China; the long time that the patients have to wait for is the main phenomenon of difficult medical service. Medical industry is service-oriented and its main purpose is to make profits, so the benefits and competitiveness of a hospital depend on patient satisfaction. This paper makes a survey on a large hospital in Harbin of China and collects relevant data and then uses the prospect theory to analyze patients’ and doctors’ behavioral characteristics and the model of patient satisfaction is established based on fuzzy theory with a triplet α/β/γ. The optimal scheduling of clinic is described as a problem with the rule of first come, first served which maximizes patient satisfaction for the main goal and minimizes operating costs for the secondary goal. And the corresponding mathematical model is established. Finally, a solution method named plant growth simulation algorithm (PGSA is presented. Then, by means of calculating of the example and comparing with genetic algorithm, the results show that the optimum can be reached; meanwhile the efficiency of the presented algorithm is better than the genetic algorithm.

  3. Method for forming permanent magnets with different polarities for use in microelectromechanical devices

    Science.gov (United States)

    Roesler, Alexander W [Tijeras, NM; Christenson, Todd R [Albuquerque, NM

    2007-04-24

    Methods are provided for forming a plurality of permanent magnets with two different north-south magnetic pole alignments for use in microelectromechanical (MEM) devices. These methods are based on initially magnetizing the permanent magnets all in the same direction, and then utilizing a combination of heating and a magnetic field to switch the polarity of a portion of the permanent magnets while not switching the remaining permanent magnets. The permanent magnets, in some instances, can all have the same rare-earth composition (e.g. NdFeB) or can be formed of two different rare-earth materials (e.g. NdFeB and SmCo). The methods can be used to form a plurality of permanent magnets side-by-side on or within a substrate with an alternating polarity, or to form a two-dimensional array of permanent magnets in which the polarity of every other row of the array is alternated.

  4. A Novel GMM-Based Behavioral Modeling Approach for Smartwatch-Based Driver Authentication.

    Science.gov (United States)

    Yang, Ching-Han; Chang, Chin-Chun; Liang, Deron

    2018-03-28

    All drivers have their own distinct driving habits, and usually hold and operate the steering wheel differently in different driving scenarios. In this study, we proposed a novel Gaussian mixture model (GMM)-based method that can improve the traditional GMM in modeling driving behavior. This new method can be applied to build a better driver authentication system based on the accelerometer and orientation sensor of a smartwatch. To demonstrate the feasibility of the proposed method, we created an experimental system that analyzes driving behavior using the built-in sensors of a smartwatch. The experimental results for driver authentication-an equal error rate (EER) of 4.62% in the simulated environment and an EER of 7.86% in the real-traffic environment-confirm the feasibility of this approach.

  5. The Improvement of Low Salt Diet Behavior based on Theory of Planned Behavior on Elderly with Hypertension

    Directory of Open Access Journals (Sweden)

    Lembunai Tat Alberta

    2016-09-01

    Full Text Available Introduction: Hypertension in elderly is triggered by the thickening and stiffness of arterial wall due to ageing processes. One attempt to prevent the complications of hypertension is by change their lifestyle, such as perform a low-salt diet. The implementation of a low-salt diet on elderly should be adjusted with their behavior and habits. TPB is one of theoretical attempt to identify the relationship between elderly’s attitude and their behavior, and to emphasize the importancy of intention as determinant of behavior, focused on cognitif and rational decission making process. This study was aimed to analyze the improvement of low salt diet behavior based on TPB on elderly with hypertension. Method: This research was used descriptive design with observational analytic method. Population were elderly with hypertension recorded at Puskesmas Pucang, Kota Surabaya. Samples were 32 respondents, taken randomly. Data were collected by using questionnaires and direct interview. Data were then analyzed by using Partial Least Square (PLS. Result: The results had showed that intention to implement a low-salt diet was built by attitudes toward behavior, subjective norms, and perceived behavioral control (PBC on elderly with hypertension. A low-salt diet behavior was built by intention to implement a low-salt diet on elderly with hypertension. Discussion: These results can be used as a model to improve low salt diet behavior on elderly with hypertension. Keywords: low-salt diet, hypertension, elderly, TPB

  6. Surface acid-base behaviors of Chinese loess.

    Science.gov (United States)

    Chu, Zhaosheng; Liu, Wenxin; Tang, Hongxiao; Qian, Tianwei; Li, Shushen; Li, Zhentang; Wu, Guibin

    2002-08-15

    Acid-base titration was applied to investigate the surface acid-base properties of a Chinese loess sample at different ionic strengths. The acidimetric supernatant was regarded as the system blank of titration to correct the influence of particle dissolution on the estimation of proton consumption. The titration behavior of the system blank could be described by the hydrolysis of Al3+ and Si(OH)4 in aqueous solution as well as the production of hydroxyaluminosilicates. The formation of Al-Si species on homogeneous surface sites by hydrous aluminum and silicic acid, released from solid substrate during the acidic titration, was considered in the model description of the back-titration procedure. A surface reaction model was suggested as follows: >SOHSO(-)+H+, pK(a)(int)=3.48-3.98;>SOH+Al(3+)+H4SiO4SOAl(OSi(OH)3(+)+2H+, pK(SC)=3.48-4.04. Two simple surface complexation models accounted for the interfacial structure, i.e., the constant capacitance model (CCM) and the diffuse layer model (DLM), and gave a satisfactory description of the experimental data. Considering the effect of ionic strength on the electrostatic profile at the solid-aqueous interface, the DLM was appropriate at the low concentrations (0.01 and 0.005 mol/L) of background electrolyte (NaNO3 in this study), while the CCM was preferable in the case of high ionic strength (0.1 mol/L).

  7. Visualization of Sedentary Behavior Using an Event-Based Approach

    Science.gov (United States)

    Loudon, David; Granat, Malcolm H.

    2015-01-01

    Visualization is commonly used in the interpretation of physical behavior (PB) data, either in conjunction with or as precursor to formal analysis. Effective representations of the data can enable the identification of patterns of behavior, and how they relate to the temporal context in a single day, or across multiple days. An understanding of…

  8. Scanpath Based N-Gram Models for Predicting Reading Behavior

    DEFF Research Database (Denmark)

    Mishra, Abhijit; Bhattacharyya, Pushpak; Carl, Michael

    2013-01-01

    Predicting reading behavior is a difficult task. Reading behavior depends on various linguistic factors (e.g. sentence length, structural complexity etc.) and other factors (e.g individual's reading style, age etc.). Ideally, a reading model should be similar to a language model where the model i...

  9. The Effect of Multiple Intelligences Theory (MIT)-based Instruction on Attitudes towards the Course, Academic Success, and Permanence of Teaching on the Topic of "Respiratory Systems"

    Science.gov (United States)

    Koksal, Mustafa Serdar; Yel, Mustafa

    2007-01-01

    Studies on the effective teaching of biology have been continuously increasing since the 1800s. New teaching approaches have been purposed and tried out along the way. The multiple intelligences theory (MIT)-based approaches which give more importance to individual in educational settings can provide alternatives for meeting this requirement. An…

  10. Investigation of the Precipitation Behavior in Aluminum Based Alloys

    KAUST Repository

    Khushaim, Muna S.

    2015-11-30

    The transportation industries are constantly striving to achieve minimum weight to cut fuel consumption and improve overall performance. Different innovative design strategies have been placed and directed toward weight saving combined with good mechanical behavior. Among different materials, aluminum-based alloys play a key role in modern engineering and are widely used in construction components because of their light weight and superior mechanical properties. Introduction of different nano-structure features can improve the service and the physical properties of such alloys. For intelligent microstructure design in the complex Al-based alloy, it is important to gain a deep physical understanding of the correlation between the microstructure and macroscopic properties, and thus atom probe tomography with its exceptional capabilities of spatially resolution and quantitative chemical analyses is presented as a sophisticated analytical tool to elucidate the underlying process of precipitation phenomena in aluminum alloys. A complete study examining the influence of common industrial heat treatment on the precipitation kinetics and phase transformations of complex aluminum alloy is performed. The qualitative evaluation results of the precipitation kinetics and phase transformation as functions of the heat treatment conditions are translated to engineer a complex aluminum alloy. The study demonstrates the ability to construct a robust microstructure with an excellent hardness behavior by applying a low-energy-consumption, cost-effective method. The proposed strategy to engineer complex aluminum alloys is based on both mechanical strategy and intelligent microstructural design. An intelligent microstructural design requires an investigation of the different strengthen phases, such as T1 (Al2CuLi), θ′(Al2Cu), β′(Al3Zr) and δ′(Al3Li). Therefore, the early stage of phase decomposition is examined in different binary Al-Li and Al-Cu alloys together with different

  11. Variable high gradient permanent magnet quadrupole (QUAPEVA)

    Science.gov (United States)

    Marteau, F.; Ghaith, A.; N'Gotta, P.; Benabderrahmane, C.; Valléau, M.; Kitegi, C.; Loulergue, A.; Vétéran, J.; Sebdaoui, M.; André, T.; Le Bec, G.; Chavanne, J.; Vallerand, C.; Oumbarek, D.; Cosson, O.; Forest, F.; Jivkov, P.; Lancelot, J. L.; Couprie, M. E.

    2017-12-01

    Different applications such as laser plasma acceleration, colliders, and diffraction limited light sources require high gradient quadrupoles, with strength that can reach up to 200 T/m for a typical 10 mm bore diameter. We present here a permanent magnet based quadrupole (so-called QUAPEVA) composed of a Halbach ring and surrounded by four permanent magnet cylinders. Its design including magnetic simulation modeling enabling us to reach 201 T/m with a gradient variability of 45% and mechanical issues are reported. Magnetic measurements of seven systems of different lengths are presented and confirmed the theoretical expectations. The variation of the magnetic center while changing the gradient strength is ±10 μm. A triplet of QUAPEVA magnets is used to efficiently focus a beam with large energy spread and high divergence that is generated by a Laser Plasma Acceleration source for a free electron laser demonstration and has enabled us to perform beam based alignment and control the dispersion of the beam.

  12. Sealing Occlusal Dentin Caries in Permanent Molars

    DEFF Research Database (Denmark)

    Qvist, Vibeke; Borum, Mette Kit; Møller, Kirsten Dynes

    2017-01-01

    The purpose of this study was to investigate the possibility of postponing restorative intervention of manifest occlusal caries in young, permanent dentition by non-invasive sealing. This RCT-designed study included 521 occlusal lesions in 521 patients aged 6 to 17 y. Based on clinical and radiog......The purpose of this study was to investigate the possibility of postponing restorative intervention of manifest occlusal caries in young, permanent dentition by non-invasive sealing. This RCT-designed study included 521 occlusal lesions in 521 patients aged 6 to 17 y. Based on clinical...... longevity of sealings and restorations until retreatments, and 3) compare effectiveness of sealings and restorations to halt caries progression in sealed lesions and beneath restorations. Furthermore, we aimed to identify factors influencing longevity and the effectiveness of sealings and restorations.......001). The median survival time for sealings not replaced by restorations was 7.3 y (CI, 6.4 y to NA). Survival of sealings was increased in patients with low caries risk and/or excellent oral hygiene, second molars compared with first molars, and lesions not extending the middle one-third of the dentin. Survival...

  13. Permanent magnets including undulators and wigglers

    CERN Document Server

    Bahrdt, J

    2010-01-01

    After a few historic remarks on magnetic materials we introduce the basic definitions related to permanent magnets. The magnetic properties of the most common materials are reviewed and the production processes are described. Measurement techniques for the characterization of macroscopic and microscopic properties of permanent magnets are presented. Field simulation techniques for permanent magnet devices are discussed. Today, permanent magnets are used in many fields. This article concentrates on the applications of permanent magnets in accelerators starting from dipoles and quadrupoles on to wigglers and undulators.

  14. Web-Based Instruction, Learning Effectiveness and Learning Behavior: The Impact of Relatedness

    Science.gov (United States)

    Shieh, Chich-Jen; Liao, Ying; Hu, Ridong

    2013-01-01

    This study aims to discuss the effects of Web-based Instruction and Learning Behavior on Learning Effectiveness. Web-based Instruction contains the dimensions of Active Learning, Simulation-based Learning, Interactive Learning, and Accumulative Learning; and, Learning Behavior covers Learning Approach, Learning Habit, and Learning Attitude. The…

  15. Insertion of a single-molecule magnet inside a ferromagnetic lattice based on a 3D bimetallic oxalate network: towards molecular analogues of permanent magnets.

    Science.gov (United States)

    Clemente-León, Miguel; Coronado, Eugenio; Gómez-García, Carlos J; López-Jordà, Maurici; Camón, Agustín; Repollés, Ana; Luis, Fernando

    2014-02-03

    The insertion of the single-molecule magnet (SMM) [Mn(III)(salen)(H2O)]2(2+) (salen(2-) = N,N'-ethylenebis-(salicylideneiminate)) into a ferromagnetic bimetallic oxalate network affords the hybrid compound [Mn(III)(salen)(H2O)]2[Mn(II)Cr(III)(ox)3]2⋅(CH3OH)⋅(CH3CN)2 (1). This cationic Mn2 cluster templates the growth of crystals formed by an unusual achiral 3D oxalate network. The magnetic properties of this hybrid magnet are compared with those of the analogous compounds [Mn(III)(salen)(H2O)]2[Zn(II)Cr(III)(ox)3]2⋅(CH3OH)⋅(CH3CN)2 (2) and [In(III)(sal2-trien)][Mn(II)Cr(III)(ox)3]⋅(H2O)0.25⋅(CH3OH)0.25⋅(CH3CN)0.25 (3), which are used as reference compounds. In 2 it has been shown that the magnetic isolation of the Mn2 clusters provided by their insertion into a paramagnetic oxalate network of Cr(III) affords a SMM behavior, albeit with blocking temperatures well below 500 mK even for frequencies as high as 160 kHz. In 3 the onset of ferromagnetism in the bimetallic Mn(II) Cr(III) network is observed at Tc = 5 K. Finally, in the hybrid compound 1 the interaction between the two magnetic networks leads to the antiparallel arrangement of their respective magnetizations, that is, to a ferrimagnetic phase. This coupling induces also important changes on the magnetic properties of 1 with respect to those of the reference compounds 2 and 3. In particular, compound 1 shows a large magnetization hysteresis below 1 K, which is in sharp contrast with the near-reversible magnetizations that the SMMs and the oxalate ferromagnetic lattice show under the same conditions. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Predicting Factors of Worker Behavior for Proper Working Posture Based on Planed Behavior Theory

    Directory of Open Access Journals (Sweden)

    E Mohammadi Zeydi

    2008-12-01

    Introduction & Objective: Injuries resulting from ignoring proper working posture especially in employees who sitting at workplace for more than of working hours are costly, and create significant pain and discomfort. Decreasing of these injuries is most effectively accomplished through the application of ergonomic design principles. Sometimes, however, barriers (technical and economic preclude ergonomic improvement and, consequently, some organizations rely on the use of proper sitting techniques and maintaining proper working posture as a major control strategy during workday. The problem, however, is that these process performing is inconsistent and managers have a difficult time motivating use of these techniques. The main aim of this study was to understand the factors driving proper working posture among employees. Materials & Methods: This study used the theory of planned behavior to predict upright working posture maintenance among 222 of assembling, machinery and printing line’s employees at a Qazvin Alborz industrial town manufacturing organization. Structural equation modeling, explanatory and confirmatory factor analysis were employed to analyze relationships among constructs. Results: Results revealed that attitude (p< 0.05, β= 0.53 and intention (p< 0.05, β= 0.46 were the strongest predictors of proper working posture maintenance behavior. Perceived behavior control, to a lesser degree, were also important influences on intention (p< 0.05, β= 0.34 and behavior (p< 0.05, β= 0.28. Subjective norms did not surface as effective direct predictors of upright working posture maintenance, but did affect behavior and intent via mediating factors (attitudes subjective norms and perceived behavioral control. Finally, the TPB was supported as an effective model explaining upright working posture maintenance, and had potential application for many other safety-related behaviors. Conclusion: results of this study emphasis on considering factors such as

  17. A Self-Administered Parent Training Program Based upon the Principles of Applied Behavior Analysis

    Science.gov (United States)

    Maguire, Heather M.

    2012-01-01

    Parents often respond to challenging behavior exhibited by their children in such a way that unintentionally strengthens it. Applied behavior analysis (ABA) is a research-based science that has been proven effective in remediating challenging behavior in children. Although many parents could benefit from using strategies from the field of ABA with…

  18. Behavior-based environmental attitude : development of an instrument for adolescents

    NARCIS (Netherlands)

    Kaiser, F.G.; Oerke, B.; Bogner, F.X.

    2007-01-01

    Due to the omnipresent attitude–behavior gap, conservation psychologists have ceased to believe that attitudes are traceable from people's behavioral records. In contrast to this conventional wisdom and to the current state of the art in attitude measurement, we developed a behavior-based attitude

  19. Optimally segmented permanent magnet structures

    DEFF Research Database (Denmark)

    Insinga, Andrea Roberto; Bjørk, Rasmus; Smith, Anders

    2016-01-01

    We present an optimization approach which can be employed to calculate the globally optimal segmentation of a two-dimensional magnetic system into uniformly magnetized pieces. For each segment the algorithm calculates the optimal shape and the optimal direction of the remanent flux density vector......, with respect to a linear objective functional. We illustrate the approach with results for magnet design problems from different areas, such as a permanent magnet electric motor, a beam focusing quadrupole magnet for particle accelerators and a rotary device for magnetic refrigeration....

  20. Behaviorism

    Science.gov (United States)

    Moore, J.

    2011-01-01

    Early forms of psychology assumed that mental life was the appropriate subject matter for psychology, and introspection was an appropriate method to engage that subject matter. In 1913, John B. Watson proposed an alternative: classical S-R behaviorism. According to Watson, behavior was a subject matter in its own right, to be studied by the…

  1. Simulation Study of Swarm Intelligence Based on Life Evolution Behavior

    OpenAIRE

    Yanmin Liu; Ying Bi; Changling Sui; Yuanfeng Luo; Zhuanzhou Zhang; Rui Liu

    2015-01-01

    Swarm intelligence (SI) is a new evolutionary computation technology, and its performance efficacy is usually affected by each individual behavior in the swarm. According to the genetic and sociological theory, the life evolution behavior process is influenced by the external and internal factors, so the mechanisms of external and internal environment change must be analyzed and explored. Therefore, in this paper, we used the thought of the famous American genetic biologist Morgan, “life = DN...

  2. Permanent burying method for product

    International Nuclear Information System (INIS)

    Sakai, Goro; Sakata, Noboru; Hironaka, Yoshikazu; Shigematsu, Kazuo; Yurugi, Masahiro; Minami, Masayoshi; Yoshisaki, Masato.

    1995-01-01

    In a method of permanently burying an object by filling and solidifying a cement mortar in gaps between each of objects to be buried underground, cement mortar is filled into gaps, which comprises water at a unit amount determined as from 200 to 250kg/m 3 , a cement at low water/cement ratio (%) of from 70 to 400%, and contains fine powder having an average grain size of not greater than 100μm (not containing cement) of 50 to 800kg/m 3 , fine aggregates of 800 to 1200kg/m 3 , UERAN gum (a bio-gum powder produced by aerobic fermentation of alcaligenes-bacteria) of 20g/m 3 to 1.3kg/m 3 , a dispersing agent of 0 to 40kg/m 3 , a swelling agent of 0 to 40kg/m 3 . Then if the mortar blended with the UERAN gum is injected, any gaps can be filled tightly, no breeding is caused and since the amount of cement is small, it does not suffer from temperature cracking. Therefore, the state of filling is kept permanently, and environmental pollution caused by radioactive wastes can be prevented. (N.H.)

  3. Object permanence and working memory in cats (Felis catus).

    Science.gov (United States)

    Goulet, S; Doré, F Y; Rousseau, R

    1994-10-01

    Cats (Felis catus) find an object when it is visibly moved behind a succession of screens. However, when the object is moved behind a container and is invisibly transferred from the container to the back of a screen, cats try to find the object at or near the container rather than at the true hiding place. Four experiments were conducted to study search behavior and working memory in visible and invisible displacement tests of object permanence. Experiment 1 compared performance in single and in double visible displacement trials. Experiment 2 analyzed search behavior in invisible displacement tests and in analogs using a transparent container. Experiments 3 and 4 tested predictions made from Experiment 1 and 2 in a new situation of object permanence. Results showed that only the position changes that cats have directly perceived are encoded and activated in working memory, because they are unable to represent or infer invisible movements.

  4. Improving intercultural competency in global IT projects through recognition of culture-based behaviors

    Directory of Open Access Journals (Sweden)

    Richard Amster

    2016-01-01

    Full Text Available The success of global IT projects is highly influenced by culture-based behaviors. Issues between individuals arise when behaviors are (mis-perceived, (mis-interpreted, and (mis-judged by using the perceiver’s expectations, beliefs, and values. Misperception results when the behavior is not anticipated because it would not occur in ones own culture. As a result, behavior should be the starting point for cross-cultural research. But, studies have primarily focused on belief and value systems which are more abstract and less specific than behaviors. This paper presents a study that analyzed cultural behavioral differences between Indian project managers and their counterparts in other countries. The conducted qualitative, semi-structured interviews revealed insights into cross-cultural challenges and shed light on the complex ways that culture-based behaviors impact IT projects. The study identified 127 behaviors that significantly affected project success and cross-cultural cooperation between Indian managers and managers from all over the world. These behaviors were grouped into 19 behavior clusters. Understanding these behavior clusters, and correlating these behaviors to values and beliefs, will improve project collaboration, and inform cross-cultural training strategies. In addition, existing cultural dimensions were reduced in scope, additional dimensions were defined for clarity, and new business-related dimensions were identified. Finally, based on the study’s results, the paper suggests four important components that should be added to cross-cultural training programs for international project managers.

  5. Effect of Theory of Planned Behavior-based Educational Intervention on Breastfeeding Behavior in Pregnant Women in Fasa City, Iran

    Directory of Open Access Journals (Sweden)

    Seyedeh Marjan Arshad

    2017-09-01

    Full Text Available Background and Objective: Breastfeeding is a matter of significant importance. Given the role of such factors as attitude and subjective norms on the behavior of mothers and the low level of exclusive breastfeeding, the present study aimed to determine the effect of educational program based on the theory of planned behavior on breastfeeding behavior among the pregnant women in Fasa, Iran. Materials and Methods: This quasi-experimental study was conducted on 100 pregnant women with the gestational age of 30-35 weeks who referred to the health care centers of Fasa, Iran, in 2017. The study population was selected using random sampling technique, and then assigned into two groups of control (n=50 and intervention (n=50. The data were collected using a demographic form, components of the theory of planned behavior questionnaire, and a breastfeeding checklist. The intervention group received three 55-to-60-minute training sessions. The mothers' breastfeeding behavior was evaluated before the training sessions and 40 days post-delivery in both groups. The data were analyzed in SPSS software, version 22, using Chi-square test, independent t-test, and paired sample t-test. Results: According to the results, there was no significant difference between the two groups in terms of the components of the theory of planned behavior before the educational intervention (P=0.208. However, after the training sessions, the intervention group showed a significant improvement in all components of the theory of planned behavior, including intention and breastfeeding behavior, compared to the control group (P=0.001. Conclusion: Based on the findings of this study, appropriate training programs, social network support, and suitable conditions for breastfeeding in the community are among the effective factors that can change the mothers’ attitudes towards lactation and result in successful breastfeeding in the first three months after childbirth.

  6. SU-F-19A-07: Is a Day30 Scan Necessary to Evaluate Activity-Based Regulatory Compliance in Permanent Interstitial Brachytherapy for Prostate Cancer?

    Energy Technology Data Exchange (ETDEWEB)

    Kapur, P; Ford, J; Moghanaki, D; Datsang, R; Chang, M; Rosu, M [Virginia Commonwealth University, Richmond, Virginia (United States); Veterans Affairs Medical Center, Richmond, VA (United States); Hagan, M; Palta, J [Virginia Commonwealth University, Richmond, Virginia (United States); Veterans Affairs Medical Center, Richmond, VA (United States); National Radiation Oncology Program, Richmond, VA (United States)

    2014-06-15

    Purpose: To evaluate the Medical Event (ME) criteria for I-125 prostate implants based on the assessment of post implant dosimetry on “Day0”/“Day30” imaging. The new ME criteria do not mandate a timeframe for this assessment. The compliance criteria are: more than 80% of the activity from the written directive for treatment site (TS) must be implanted inside TS, and doses to 1cc of either uninvolved rectum (D1-UR) or uninvolved bladder (D1-UB), or 2cc of other non-specified tissue (D2-UT) must be less than 150% of the planned dose. Methods: “Day0”/“Day30” post-implant analyses for 25 patients were evaluated. Treatment plans had a peripheral loading pattern with 2 core needles placed at least 10 mm away from urethra, with several seeds planned outside of the prostate for adequate target coverage. TS were a uniform 5 mm expansion of the prostate, except posteriorly (no expansion). Results: “Day0”/“Day30”analyses found no MEs. The relative changes for D1-UR, D1-UB, and D2-UT were (ranges): [−37.0, 38.2]%, [−96.5, 74.7]%, and [−41.2, 37.7]%. Furthermore, changes did not correlate with prostate volume changes of −18.7% [σ:16.0%, range:−60.5%, +6.4%]. These unfavorable changes did not lead to ME at “Day30” because these values were generally well below 150% at “Day0”. However, D2-UT dose values exceeded those for D1-UR and D1-UB at both “Day0”/“Day30”. Conclusion: The total activity was relatively insensitive to changes in target volume from “Day0” to ”Day30”. The dose metrics of interest, albeit susceptible to large, often unfavorable changes, remained less than the 150% threshold. Data from this study suggest that “Day0” can be used for the regulatory compliance evaluation. However, further evaluation at “Day30” is advisable if D2-UT is 110% or above (based on the largest D2-UT increase of 37.7% observed in this patient population). Future rigorous statistical analysis of a larger cohort will afford a

  7. Automatic design of permanent magnet coupling

    International Nuclear Information System (INIS)

    Yonnet, J.-P.; Pandele, P.; Coutel, C.; Wurtz, F.

    1998-01-01

    Up to now, two main methods have been used to design permanent magnet couplings : finite element calculation, and analytical expressions of the forces between the magnets. The two methods use the same starting point, the permanent magnet coupling dimensions. The calculated parameters are the forces and the torques. The optimization of the couplings shape is generally done by using different curves describing torque variations as a function of the different geometrical parameters. We have developed a very new approach solving the reverse problem. Choosing the value of the torque, the airgap and an optimization criterium, the new method automatically calculates the size of the magnets and the ideal number of poles. It is based on a software, PASCOSMA, using an analytical model of the coupling which can be eventually corrected by a finite element method like FLUX2D. The coupling optimization is automatically made, keeping the parameters between predefined values. For a given application, it is very easy to obtain the best design, for example with the minimum magnet volume. (orig.)

  8. Samarium-cobalt type rare earth permanent magnets

    International Nuclear Information System (INIS)

    Kamat, S.V.

    2014-01-01

    Permanent magnets are one of the oldest and largest applications of magnetic materials and form an integral part of our modern industrial society. They belong to a special class of functional materials and are characterized for remanence (flux output from the magnet), coercivity (resistance to demagnetization) and energy product (material energy density) from the second quadrant of the magnetic hysteresis loop. The reliability, stability, size, weight, cost and performance of many electro-technical devices depend mainly on the properties of permanent magnets used in them. There are three important families of permanent magnets viz., Ferrites, Alnicos and Rare Earth Permanent Magnets (REPMs) with energy product values ranging from 3 to 50 MGOe and among the front ranking high performance REPMs, SmCo 5 , Sm 2 Co 17 type and NdFeB alloys are technologically the most important materials. They are used in a wide range of applications ranging from consumer products to very specialized areas of tele-communications, microelectronics, defence, space, avionics etc. While NdFeB has the highest energy product, Sm-Co based magnets are preferred for most critical applications where temperature stability of magnetic properties is essential because of their significantly higher Curie temperatures. In this presentation some of the key challenges associated with these Sm-Co based rare earth permanent magnets will be highlighted. (author)

  9. Behavior Therapy for Tic Disorders: An Evidenced-based Review and New Directions for Treatment Research

    OpenAIRE

    McGuire, Joseph F.; Ricketts, Emily J.; Piacentini, John; Murphy, Tanya K.; Storch, Eric A.; Lewin, Adam B.

    2015-01-01

    Behavior therapy is an evidenced-based intervention with moderate-to-large treatment effects in reducing tic symptom severity among individuals with Persistent Tic Disorders (PTDs) and Tourette’s Disorder (TD). This review describes the behavioral treatment model for tics, delineates components of evidence-based behavior therapy for tics, and reviews the empirical support among randomized controlled trials for individuals with PTDs or TD. Additionally, this review discusses several challenges...

  10. Gesture-based mobile training of intercultural behavior

    DEFF Research Database (Denmark)

    Rehm, Matthias; Leichtenstern, Karin

    2012-01-01

    Cultural heuristics determine acceptable verbal and non-verbal behavior in interpersonal encounters and are often the main reason for problems in intercultural communication. In this article, we present an approach to intercultural training of non-verbal behaviors that makes use of enculturated...... virtual agents, i.e. interactive systems that take cultural heuristics for interpreting and generating behavior into account. Because current trends in intercultural training highlight the importance of a coaching approach, i.e. the ability to offer training units anytime and anywhere, the system...... of the application itself, emphasizing the importance of situated role-plays. Two evaluation studies are presented next that analyze the usability of the approach as well as the more important question of whether training with the system gives better results than traditional methods....

  11. How Family Socioeconomic Status, Peer Behaviors, and School-Based Intervention on Healthy Habits Influence Adolescent Eating Behaviors

    Science.gov (United States)

    Moreno-Maldonado, Concepción; Ramos, Pilar; Moreno, Carmen; Rivera, Francisco

    2018-01-01

    Psychologists in schools can play an important role in developing policies and programs to promote healthy eating habits. This study analyses the contributions of family socioeconomic status, peer influence (schoolmates' food consumption), and school-based nutrition interventions to explain adolescent eating behaviors. Data were obtained from the…

  12. Effects of Interventions Based in Behavior Analysis on Motor Skill Acquisition: A Meta-Analysis

    Science.gov (United States)

    Alstot, Andrew E.; Kang, Minsoo; Alstot, Crystal D.

    2013-01-01

    Techniques based in applied behavior analysis (ABA) have been shown to be useful across a variety of settings to improve numerous behaviors. Specifically within physical activity settings, several studies have examined the effect of interventions based in ABA on a variety of motor skills, but the overall effects of these interventions are unknown.…

  13. Individual Travel Behavior Modeling of Public Transport Passenger Based on Graph Construction

    Directory of Open Access Journals (Sweden)

    Quan Liang

    2018-01-01

    Full Text Available This paper presents a novel method for mining the individual travel behavior regularity of different public transport passengers through constructing travel behavior graph based model. The individual travel behavior graph is developed to represent spatial positions, time distributions, and travel routes and further forecasts the public transport passenger’s behavior choice. The proposed travel behavior graph is composed of macronodes, arcs, and transfer probability. Each macronode corresponds to a travel association map and represents a travel behavior. A travel association map also contains its own nodes. The nodes of a travel association map are created when the processed travel chain data shows significant change. Thus, each node of three layers represents a significant change of spatial travel positions, travel time, and routes, respectively. Since a travel association map represents a travel behavior, the graph can be considered a sequence of travel behaviors. Through integrating travel association map and calculating the probabilities of the arcs, it is possible to construct a unique travel behavior graph for each passenger. The data used in this study are multimode data matched by certain rules based on the data of public transport smart card transactions and network features. The case study results show that graph based method to model the individual travel behavior of public transport passengers is effective and feasible. Travel behavior graphs support customized public transport travel characteristics analysis and demand prediction.

  14. Fast Food Consumption Behaviors in High-School Students based on the Theory of Planned Behavior (TPB

    Directory of Open Access Journals (Sweden)

    Kamal Mirkarimi

    2016-07-01

    Full Text Available Background: Studies report inappropriate snack and junk food consumption patterns in children and young adults in Iran. The current survey was aimed to explore fast food consumption behaviors in high-school students based on the Theory of Planned Behavior. Materials and Methods: A cross-sectional study was done among 500 high-school students. Samples were selected based on cluster sampling method at first and simple random at second. Data were collected using a researcher-made questionnaire. To analyze, SPSS-16 and tests, including t-test, Chi-square, correlation coefficient and multiple regressions were used. Results: The monthly frequency of fast food consumption was 4.01. The TPB explained fast food use behaviors with R2 of 0.6, effectively. Results also represented that frequency of fast food consumption was meaningfully in line with behavioral intention (β = 0.60, P < 0.05 and subjective norms (β = 0.17, P < 0.05. Conclusion: It seems likely beneficial to consider important subjective norms (especially friends that may strongly effect on high-school student intention to use fast food. Also students perceived behavioral control must be increased.

  15. CHALLENGES OF PERMANENT TEACHER TRAINING

    Directory of Open Access Journals (Sweden)

    María Manuela Valles-Ornelas

    2015-07-01

    Full Text Available The new challenges for teachers and managers require to assume permanent formation as a tool for responding effectively and efficiently to them, different perspective to strengthen from the initial teacher education programs. The research was done in a primary school in the state of Chihuahua. The method used was research action, the question was: How can we encourage the lifelong learning and training of the staff of this school, with the purpose to assist them in these processes to improve the service that the school provides to students. The school group is the center of the process, the cooperative and collaborative work accompanied by educational leadership and persuasive provide better results, and all accompanied by the professional selfinvitation.

  16. Magnet pole shape design for reduction of thrust ripple of slotless permanent magnet linear synchronous motor with arc-shaped magnets considering end-effect based on analytical method

    Directory of Open Access Journals (Sweden)

    Kyung-Hun Shin

    2017-05-01

    Full Text Available The shape of the magnet is essential to the performance of a slotless permanent magnet linear synchronous machine (PMLSM because it is directly related to desirable machine performance. This paper presents a reduction in the thrust ripple of a PMLSM through the use of arc-shaped magnets based on electromagnetic field theory. The magnetic field solutions were obtained by considering end effect using a magnetic vector potential and two-dimensional Cartesian coordinate system. The analytical solution of each subdomain (PM, air-gap, coil, and end region is derived, and the field solution is obtained by applying the boundary and interface conditions between the subdomains. In particular, an analytical method was derived for the instantaneous thrust and thrust ripple reduction of a PMLSM with arc-shaped magnets. In order to demonstrate the validity of the analytical results, the back electromotive force results of a finite element analysis and experiment on the manufactured prototype model were compared. The optimal point for thrust ripple minimization is suggested.

  17. A Kinect-based system for automatic recording of some pigeon behaviors.

    Science.gov (United States)

    Lyons, Damian M; MacDonall, James S; Cunningham, Kelly M

    2015-12-01

    Contact switches and touch screens are the state of the art for recording pigeons' pecking behavior. Recording other behavior, however, requires a different sensor for each behavior, and some behaviors cannot easily be recorded. We present a flexible and inexpensive image-based approach to detecting and counting pigeon behaviors that is based on the Kinect sensor from Microsoft. Although the system is as easy to set up and use as the standard approaches, it is more flexible because it can record behaviors in addition to key pecking. In this article, we show how both the fast, fine motion of key pecking and the gross body activity of feeding can be measured. Five pigeons were trained to peck at a lighted contact switch, a pigeon key, to obtain food reward. The timing of the pecks and the food reward signals were recorded in a log file using standard equipment. The Kinect-based system, called BehaviorWatch, also measured the pecking and feeding behavior and generated a different log file. For key pecking, BehaviorWatch had an average sensitivity of 95% and a precision of 91%, which were very similar to the pecking measurements from the standard equipment. For detecting feeding activity, BehaviorWatch had a sensitivity of 95% and a precision of 97%. These results allow us to demonstrate that an advantage of the Kinect-based approach is that it can also be reliably used to measure activity other than key pecking.

  18. Behavior-Based Budget Management Using Predictive Analytics

    Energy Technology Data Exchange (ETDEWEB)

    Troy Hiltbrand

    2013-03-01

    Historically, the mechanisms to perform forecasting have primarily used two common factors as a basis for future predictions: time and money. While time and money are very important aspects of determining future budgetary spend patterns, organizations represent a complex system of unique individuals with a myriad of associated behaviors and all of these behaviors have bearing on how budget is utilized. When looking to forecasted budgets, it becomes a guessing game about how budget managers will behave under a given set of conditions. This becomes relatively messy when human nature is introduced, as different managers will react very differently under similar circumstances. While one manager becomes ultra conservative during periods of financial austerity, another might be un-phased and continue to spend as they have in the past. Both might revert into a state of budgetary protectionism masking what is truly happening at a budget holder level, in order to keep as much budget and influence as possible while at the same time sacrificing the greater good of the organization. To more accurately predict future outcomes, the models should consider both time and money and other behavioral patterns that have been observed across the organization. The field of predictive analytics is poised to provide the tools and methodologies needed for organizations to do just this: capture and leverage behaviors of the past to predict the future.

  19. Behavioral Finance and Agent-Based Artificial Markets

    NARCIS (Netherlands)

    M. Lovric (Milan)

    2011-01-01

    textabstractStudying the behavior of market participants is important due to its potential impact on asset prices and the dynamics of financial markets. The idea of individual investors who are prone to biases in judgment and who use various heuristics, which might lead to anomalies on the market

  20. Oxide characterization and hydrogen behaviors of Zr-based alloys

    International Nuclear Information System (INIS)

    Kim, Y. S.; Kim, D. J.; Kwon, S. H.; Lee, H. S.; Oh, S. J.; Yim, B. J.; Son, S. B.; Yun, S. P.

    2006-03-01

    The work scope and contents of the research are as follows : basic properties of zirconium alloys, hydrogen pick-up mechanism of zirconium alloy, effects of hydride on the corrosion behaviors of zirconium alloys, estimation on stress of oxide layer in the zirconium alloy, microstructure and characteristic of oxide in pre-hydrided zirconium alloys

  1. Experience with the behavior-basedRobot development

    DEFF Research Database (Denmark)

    Marian, Nicolae; Bilberg, Arne

    with children, assists elderly or approaches people in air-ports for helping them on their way, must watch human movements, interpret what their intentions are and act accordingly. The paper gives an introduction of various BBR and their relation with sensors, presents a technique for representing behaviors...

  2. Characterization of the Tribological Behavior of Graphene-Based Additives

    Energy Technology Data Exchange (ETDEWEB)

    Erck, Robert

    2014-09-01

    XG-supplied nanocrystalline additives were extensively tested for friction and wear behavior. A technique for investigating the stability of additives was developed, and a report covered filtration and centrifugation methods for settling and filterable content. Friction and wear trends in partially and fully formulated oils were reported. Particle size analysis was performed and reported.

  3. Modern permanent magnetic materials - preparation and properties

    International Nuclear Information System (INIS)

    Rodewald, W.

    1989-01-01

    First of all, the basic properties of the classical (steel, AlNiCo) permanent magnetic materials and the modern rare-earth (RE) permanent magnetic materials are compared. Since the properties of RE permanent magnets depend on the particular production process, the fundamentals of the main industrial processes (powder metallurgy, rapid-solidification technique) are described and the typical properties are explained. Furthermore the production processes in development such as mechanical alloying, melt spinning technique and extrusion upsetting are briefly outlined. For applying the permanent magnets, they have to be completely magnetized. The magnetization behaviour of the various RE permanent magnets is discussed by means of the internal demagnetization curve. Finally the various influences on the temperature stability of RE permanent magnets are compiled. (orig./MM) [de

  4. Contributory Factors Related to Permanent Deformation of Hot Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Alaa Husein Abd

    2017-03-01

    Full Text Available Permanent deformation (Rutting of asphalt pavements which appears in many roads in Iraq, have caused a major impact on pavement performance by reducing the useful service life of pavement and creating services hazards for highway users. The main objective of this research is investigating the effect of some contributory factors related to permanent deformation of asphalt concrete mixture. To meet the objectives of this research, available local materials are used including asphalt binder, aggregates, mineral filler and modified asphalt binder. The Superpave mix design system was adopted with varying volumetric compositions. The Superpave Gyratory Compactor was used to compact 24 asphalt concrete cylindrical specimens. To collect the required data and investigate the development of permanent deformation in asphalt concrete under repeated loadings, Wheel-Tracking apparatus has been used in a factorial testing program during which 44 slab samples; with dimensions of 400×300×50 mm; were tested to simulate . actual pavement. Based on wheel-tracking test results, it has been concluded that increasing the compaction temperature from 110 to 150ºC caused a decreasing in permanent deformation by 20.5 and 15.6 percent for coarse and fine gradation control asphalt mixtures respectively. While the permanent deformation decreased about 21.3 percent when the compaction temperature is increased from 110 to 150ºC for coarse gradation asphalt mixtures modified with styrene butadiene styrene SBS with 3 percent by asphalt binder weight.

  5. Intrusive luxation of 60 permanent incisors

    DEFF Research Database (Denmark)

    Tsilingaridis, Georgios; Malmgren, Barbro; Andreasen, Jens O

    2012-01-01

      Intrusive luxation in the permanent dentition is an uncommon injury but it is considered one of the most severe types of dental trauma because of the risk for damage to the periodontal ligament, pulp and alveolar bone. Management of intrusive luxation in the permanent dentition is controversial....... The purpose of this study was to evaluate pulp survival and periodontal healing in intrusive luxated permanent teeth in relation to treatment alternatives, degree of intrusion and root development....

  6. A comparative analysis of the morphology and evolution of permanent sperm depletion in spiders.

    Directory of Open Access Journals (Sweden)

    Peter Michalik

    2011-01-01

    Full Text Available Once thought to be energetically cheap and easy to produce, empirical work has shown that sperm is a costly and limited resource for males. In some spider species, there is behavioral evidence that sperm are permanently depleted after a single mating. This extreme degree of mating investment appears to co-occur with other reproductive strategies common to spiders, e.g. genital mutilation and sexual cannibalism. Here we corroborate that sperm depletion in the golden orb-web spider Nephila clavipes is permanent by uncovering its mechanistic basis using light and electron microscopy. In addition, we use a phylogeny-based statistical analysis to test the evolutionary relationships between permanent sperm depletion (PSD and other reproductive strategies in spiders. Male testes do not produce sperm during adulthood, which is unusual in spiders. Instead, spermatogenesis is nearly synchronous and ends before the maturation molt. Testis size decreases as males approach their maturation molt and reaches its lowest point after sperm is transferred into the male copulatory organs (pedipalps. As a consequence, the amount of sperm available to males for mating is limited to the sperm contained in the pedipalps, and once it is used, males lose their ability to fertilize eggs. Our data suggest that PSD has evolved independently at least three times within web-building spiders and is significantly correlated with the evolution of other mating strategies that limit males to monogamy, including genital mutilation and sexual cannibalism. We conclude that PSD may be an energy-saving adaptation in species where males are limited to monogamy. This could be particularly important in web-building spiders where extreme sexual size dimorphism results in large, sedentary females and small, searching males who rarely feed as adults and are vulnerable to starvation. Future work will explore possible energetic benefits and the evolutionary lability of PSD relative to other

  7. Experimental Comparison of the Behavior between Base Oil and Grease Starvation Based on Inlet Film Thickness

    Directory of Open Access Journals (Sweden)

    D. Kostal

    2017-03-01

    Full Text Available This paper deals with the experimental study of an elastohydrodynamic contact under conditions of insufficient lubricant supply. Starvation level of this type of the contact may be experimentally determined based on the position of the meniscus, but this way can't determine all levels of starvation. Consequent development in the field of tribology achieved theoretical model that can determine all levels of starvation by dependency on the thickness of the lubricant film entering the contact, but it is difficult for experimental verification. The main goal of this work is an experimental study and description of the behavior of the elastohydrodynamic contact with controlled thickness of the lubricant film at the contact input. Contact was lubricated by the base oil and the grease and compared. Results were surprising because the only differences between oil and grease were observed for more viscous lubricants at thicker film layer entering to the contact.

  8. Forces between permanent magnets: experiments and model

    International Nuclear Information System (INIS)

    González, Manuel I

    2017-01-01

    This work describes a very simple, low-cost experimental setup designed for measuring the force between permanent magnets. The experiment consists of placing one of the magnets on a balance, attaching the other magnet to a vertical height gauge, aligning carefully both magnets and measuring the load on the balance as a function of the gauge reading. A theoretical model is proposed to compute the force, assuming uniform magnetisation and based on laws and techniques accessible to undergraduate students. A comparison between the model and the experimental results is made, and good agreement is found at all distances investigated. In particular, it is also found that the force behaves as r −4 at large distances, as expected. (paper)

  9. Predictors of Tobacco Smoking in Male Adolescents in Hamadan Based on the Theory of Planned Behavior

    Directory of Open Access Journals (Sweden)

    Majid Barati

    2014-12-01

    Full Text Available Background and Objectives: The cognitive determinants of social behaviors play an important role in adolescents' decision-making for starting smoking. The present study was therefore conducted to determine the predictors of tobacco smoking in male adolescents in Hamadan, Iran, based on the Theory of Planned Behavior (TPB. Materials and Methods: The present descriptive-analytical study was conducted on 810 male high school students in Hamadan selected through the multistage sampling method. Data were collected using a self-report questionnaire with a section on participants' demographic information and another section based on the TPB constructs. Data were then analyzed in SPSS-18 and AMOS-18 using the Pearson correlation test and the indices of model fit. Results: Overall, 17.2% of the male adolescents reported to have smoked cigarettes in the past. Perceived behavioral control, subjective norms and attitude were the best predictors of behavioral intention for tobacco smoking, in the order of importance (P<0.001. Perceived behavioral control (&beta=-0.59 P<0.001 was a better predictor of the studied behavior than behavioral intention (&beta=0.11 P<0.001. In the structural equation model, TPB constructs accounted for 32% of behavioral intention variances and 50% of behavior variances. Conclusion: The results demonstrated the poor role of behavioral intention in reporting smoking behaviors in male adolescents. Other psychological factors that affect adolescents' decision-making regarding tobacco smoking should also be scrutinized.

  10. Redox-Based Regulation of Bacterial Development and Behavior.

    Science.gov (United States)

    Sporer, Abigail J; Kahl, Lisa J; Price-Whelan, Alexa; Dietrich, Lars E P

    2017-06-20

    Severe changes in the environmental redox potential, and resulting alterations in the oxidation states of intracellular metabolites and enzymes, have historically been considered negative stressors, requiring responses that are strictly defensive. However, recent work in diverse organisms has revealed that more subtle changes in the intracellular redox state can act as signals, eliciting responses with benefits beyond defense and detoxification. Changes in redox state have been shown to influence or trigger chromosome segregation, sporulation, aerotaxis, and social behaviors, including luminescence as well as biofilm establishment and dispersal. Connections between redox state and complex behavior allow bacteria to link developmental choices with metabolic state and coordinate appropriate responses. Promising future directions for this area of study include metabolomic analysis of species- and condition-dependent changes in metabolite oxidation states and elucidation of the mechanisms whereby the redox state influences circadian regulation.

  11. Identifying Method of Drunk Driving Based on Driving Behavior

    Directory of Open Access Journals (Sweden)

    Xiaohua Zhao

    2011-05-01

    Full Text Available Drunk driving is one of the leading causes contributing to traffic crashes. There are numerous issues that need to be resolved with the current method of identifying drunk driving. Driving behavior, with the characteristic of real-time, was extensively researched to identify impaired driving behaviors. In this paper, the drives with BACs above 0.05% were defined as drunk driving state. A detailed comparison was made between normal driving and drunk driving. The experiment in driving simulator was designed to collect the driving performance data of the groups. According to the characteristics analysis for the effect of alcohol on driving performance, seven significant indicators were extracted and the drunk driving was identified by the Fisher Discriminant Method. The discriminant function demonstrated a high accuracy of classification. The optimal critical score to differentiate normal from drinking state was found to be 0. The evaluation result verifies the accuracy of classification method.

  12. Analysis and optimization of hybrid excitation permanent magnet synchronous generator for stand-alone power system

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Huijun, E-mail: huijun024@gmail.com [School of Instrumentation Science and Opto-electronics Engineering, Beihang University (China); Qu, Zheng; Tang, Shaofei; Pang, Mingqi [School of Instrumentation Science and Opto-electronics Engineering, Beihang University (China); Zhang, Mingju [Shanghai Aerospace Control Technology Institute, Shanghai (China)

    2017-08-15

    Highlights: • One novel permanent magnet generator structure has been proposed to reduce voltage regulation ratio. • Finite element method and equivalent circuit methods are both employed to realize rapid generator design. • Design of experiment (DOE) method is used to optimize permanent magnet shape for reduce voltage waveform distortion. • The obtained analysis and experiment results verify the proposed design methods. - Abstract: In this paper, electromagnetic design and permanent magnet shape optimization for permanent magnet synchronous generator with hybrid excitation are investigated. Based on generator structure and principle, design outline is presented for obtaining high efficiency and low voltage fluctuation. In order to realize rapid design, equivalent magnetic circuits for permanent magnet and iron poles are developed. At the same time, finite element analysis is employed. Furthermore, by means of design of experiment (DOE) method, permanent magnet is optimized to reduce voltage waveform distortion. Finally, the validity of proposed design methods is validated by the analytical and experimental results.

  13. Analysis and optimization of hybrid excitation permanent magnet synchronous generator for stand-alone power system

    International Nuclear Information System (INIS)

    Wang, Huijun; Qu, Zheng; Tang, Shaofei; Pang, Mingqi; Zhang, Mingju

    2017-01-01

    Highlights: • One novel permanent magnet generator structure has been proposed to reduce voltage regulation ratio. • Finite element method and equivalent circuit methods are both employed to realize rapid generator design. • Design of experiment (DOE) method is used to optimize permanent magnet shape for reduce voltage waveform distortion. • The obtained analysis and experiment results verify the proposed design methods. - Abstract: In this paper, electromagnetic design and permanent magnet shape optimization for permanent magnet synchronous generator with hybrid excitation are investigated. Based on generator structure and principle, design outline is presented for obtaining high efficiency and low voltage fluctuation. In order to realize rapid design, equivalent magnetic circuits for permanent magnet and iron poles are developed. At the same time, finite element analysis is employed. Furthermore, by means of design of experiment (DOE) method, permanent magnet is optimized to reduce voltage waveform distortion. Finally, the validity of proposed design methods is validated by the analytical and experimental results.

  14. Prevalence and factors affecting use of long acting and permanent ...

    African Journals Online (AJOL)

    Introduction: In Ethiopia, knowledge of contraceptive methods is high though there is low contraceptive prevalence rate. This study was aimed to assess prevalence and associated factors of long acting and permanent contraceptive methods in Jinka town, southern Ethiopia. Methods: Community based cross sectional ...

  15. Comparative analysis of various methods for modelling permanent magnet machines

    NARCIS (Netherlands)

    Ramakrishnan, K.; Curti, M.; Zarko, D.; Mastinu, G.; Paulides, J.J.H.; Lomonova, E.A.

    2017-01-01

    In this paper, six different modelling methods for permanent magnet (PM) electric machines are compared in terms of their computational complexity and accuracy. The methods are based primarily on conformal mapping, mode matching, and harmonic modelling. In the case of conformal mapping, slotted air

  16. Fixed-Time Stability Analysis of Permanent Magnet Synchronous Motors with Novel Adaptive Control

    Directory of Open Access Journals (Sweden)

    Maoxing Liu

    2017-01-01

    Full Text Available We firstly investigate the fixed-time stability analysis of uncertain permanent magnet synchronous motors with novel control. Compared with finite-time stability where the convergence rate relies on the initial permanent magnet synchronous motors state, the settling time of fixed-time stability can be adjusted to desired values regardless of initial conditions. Novel adaptive stability control strategy for the permanent magnet synchronous motors is proposed, with which we can stabilize permanent magnet synchronous motors within fixed time based on the Lyapunov stability theory. Finally, some simulation and comparison results are given to illustrate the validity of the theoretical results.

  17. Analysis and optimization of hybrid excitation permanent magnet synchronous generator for stand-alone power system

    Science.gov (United States)

    Wang, Huijun; Qu, Zheng; Tang, Shaofei; Pang, Mingqi; Zhang, Mingju

    2017-08-01

    In this paper, electromagnetic design and permanent magnet shape optimization for permanent magnet synchronous generator with hybrid excitation are investigated. Based on generator structure and principle, design outline is presented for obtaining high efficiency and low voltage fluctuation. In order to realize rapid design, equivalent magnetic circuits for permanent magnet and iron poles are developed. At the same time, finite element analysis is employed. Furthermore, by means of design of experiment (DOE) method, permanent magnet is optimized to reduce voltage waveform distortion. Finally, the validity of proposed design methods is validated by the analytical and experimental results.

  18. PRUB: A Privacy Protection Friend Recommendation System Based on User Behavior

    Directory of Open Access Journals (Sweden)

    Wei Jiang

    2016-01-01

    Full Text Available The fast developing social network is a double-edged sword. It remains a serious problem to provide users with excellent mobile social network services as well as protecting privacy data. Most popular social applications utilize behavior of users to build connection with people having similar behavior, thus improving user experience. However, many users do not want to share their certain behavioral information to the recommendation system. In this paper, we aim to design a secure friend recommendation system based on the user behavior, called PRUB. The system proposed aims at achieving fine-grained recommendation to friends who share some same characteristics without exposing the actual user behavior. We utilized the anonymous data from a Chinese ISP, which records the user browsing behavior, for 3 months to test our system. The experiment result shows that our system can achieve a remarkable recommendation goal and, at the same time, protect the privacy of the user behavior information.

  19. Permanent scatterer InSAR processing: Forsmark

    International Nuclear Information System (INIS)

    Dehls, John F.

    2006-04-01

    It has been speculated that slow, aseismic movement may be occurring along some of the fracture zones crosscutting the Forsmark area. The purpose of this study is to determine if it is possible to measure such movement using dInSAR. Differential SAR Interferometry (DInSAR) is a technique that compares the phases of multiple radar images of an area to measure surface change. The method has the potential to detect millimetric surface deformation along the sensor - target line-of-sight. Differences in phase between two images are easily viewed by combining, or interfering, the two phase-images. In the resulting image, the waves will either reinforce or cancel one another, depending upon the relative phases. The resulting image is called an interferogram and contains concentric bands of colour, or fringes, that are related to topography and/or surface deformation. New algorithms use many images acquired over a long time period to determine the movement history of individual objects, referred to as permanent scatterers. In the current project, standard PSInSAR processing was performed on 40 ERS-1 and ERS-2 scenes. The total area processed is approximately 1,500 km 2 . Slightly less than 20,000 permanent scatterers were identified.The highest densities were obtained along the coast and on the islands, where natural outcrops are more abundant. Two main classes of objects act as permanent scatterers in this area. The first are natural reflectors, such as rocks. The second are man-made reflectors, such as parts of buildings. Numerous local movements were found in the study area, relating to building subsidence, or compaction of anthropogenic fill. The dataset was divided into three groups for analysis, based upon the location of regional lineaments provided by SKB. Both statistical and geostatistical techniques were used. The median velocity of the three blocks did not differ by more than 0.2 mm/yr. This is not considered significant, given the possible magnitude of errors

  20. Permanent scatterer InSAR processing: Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Dehls, John F [Geological Survey of Norway, Trondheim (Norway)

    2006-04-15

    It has been speculated that slow, aseismic movement may be occurring along some of the fracture zones crosscutting the Forsmark area. The purpose of this study is to determine if it is possible to measure such movement using dInSAR. Differential SAR Interferometry (DInSAR) is a technique that compares the phases of multiple radar images of an area to measure surface change. The method has the potential to detect millimetric surface deformation along the sensor - target line-of-sight. Differences in phase between two images are easily viewed by combining, or interfering, the two phase-images. In the resulting image, the waves will either reinforce or cancel one another, depending upon the relative phases. The resulting image is called an interferogram and contains concentric bands of colour, or fringes, that are related to topography and/or surface deformation. New algorithms use many images acquired over a long time period to determine the movement history of individual objects, referred to as permanent scatterers. In the current project, standard PSInSAR processing was performed on 40 ERS-1 and ERS-2 scenes. The total area processed is approximately 1,500 km{sup 2}. Slightly less than 20,000 permanent scatterers were identified.The highest densities were obtained along the coast and on the islands, where natural outcrops are more abundant. Two main classes of objects act as permanent scatterers in this area. The first are natural reflectors, such as rocks. The second are man-made reflectors, such as parts of buildings. Numerous local movements were found in the study area, relating to building subsidence, or compaction of anthropogenic fill. The dataset was divided into three groups for analysis, based upon the location of regional lineaments provided by SKB. Both statistical and geostatistical techniques were used. The median velocity of the three blocks did not differ by more than 0.2 mm/yr. This is not considered significant, given the possible magnitude of

  1. 3-D analysis of eddy current in permanent magnet of interior permanent magnet motors

    International Nuclear Information System (INIS)

    Kawase, Yoshihiro; Yamaguchi, Tadashi; Fukanaga, Hiromu; Ito, Shokichi

    2002-01-01

    Interior permanent magnet motors are widely used in various fields. However, in high-speed operations, it is important to decrease the eddy current loss in the permanent magnet. In order to decrease the eddy current loss, we propose to divide the permanent magnet. In this paper, we clarified the effect of division of permanent magnet on the eddy current loss using the 3-D finite element method. (Author)

  2. An Introduction of Behavior-Based Safety Program in Nuclear Power Plants

    International Nuclear Information System (INIS)

    Lee, Yong Hee; Lim, Hyeon Kyo

    2011-01-01

    There are many methods and approaches for a human error assessment that is valuable for investigating the causes of undesirable events and counter-plans to prevent their recurrence in the nuclear power plants (NPPs). There is behavior-based safety refers to the process of using a proactive approach to safety and health management. It either focuses on risk of behaviors that can lead to an injury, or on safe behaviors that can contribute to injury prevention. Early applications of behavior based safety included the construction and manufacturing industries, but today behavior based safety is applied to a wide variety of industries and service lines. This behavior based safety program can offer a set of significant human error countermeasures to be considered for human error in NPPs as well as other fields of industry. The current methods for the human error prevention in NPPs are several techniques such as Self-Check, Peer Check, Concurrent Verification, 3-way Communication, etc. However, it is not enough to grasp the whole human error problems in operations because the things are needed in fields are a behavior technique not a simple knowledge. Therefore, we applied a behavior based safety program on the current methods

  3. Elastic Moduli of Permanently Densified Silica Glasses

    Science.gov (United States)

    Deschamps, T.; Margueritat, J.; Martinet, C.; Mermet, A.; Champagnon, B.

    2014-01-01

    Modelling the mechanical response of silica glass is still challenging, due to the lack of knowledge concerning the elastic properties of intermediate states of densification. An extensive Brillouin Light Scattering study on permanently densified silica glasses after cold compression in diamond anvil cell has been carried out, in order to deduce the elastic properties of such glasses and to provide new insights concerning the densification process. From sound velocity measurements, we derive phenomenological laws linking the elastic moduli of silica glass as a function of its densification ratio. The found elastic moduli are in excellent agreement with the sparse data extracted from literature, and we show that they do not depend on the thermodynamic path taken during densification (room temperature or heating). We also demonstrate that the longitudinal sound velocity exhibits an anomalous behavior, displaying a minimum for a densification ratio of 5%, and highlight the fact that this anomaly has to be distinguished from the compressibility anomaly of a-SiO2 in the elastic domain. PMID:25431218

  4. Individual differences in object permanence performance at 8 months: locomotor experience and brain electrical activity.

    Science.gov (United States)

    Bell, M A; Fox, N A

    1997-12-01

    This work was designed to investigate individual differences in hands-and-knees crawling and frontal brain electrical activity with respect to object permanence performance in 76 eight-month-old infants. Four groups of infants (one prelocomotor and 3 with varying lengths of hands-and-knees crawling experience) were tested on an object permanence scale in a research design similar to that used by Kermoian and Campos (1988). In addition, baseline EEG was recorded and used as an indicator of brain development, as in the Bell and Fox (1992) longitudinal study. Individual differences in frontal and occipital EEG power and in locomotor experience were associated with performance on the object permanence task. Infants successful at A-not-B exhibited greater frontal EEG power and greater occipital EEG power than unsuccessful infants. In contrast to Kermoian and Campos (1988), who noted that long-term crawling experience was associated with higher performance on an object permanence scale, infants in this study with any amount of hands and knees crawling experience performed at a higher level on the object permanence scale than prelocomotor infants. There was no interaction among brain electrical activity, locomotor experience, and object permanence performance. These data highlight the value of electrophysiological research and the need for a brain-behavior model of object permanence performance that incorporates both electrophysiological and behavioral factors.

  5. Web User Profiling Based on Browsing Behavior Analysis

    OpenAIRE

    Fan , Xiao-Xi; Chow , Kam-Pui; Xu , Fei

    2014-01-01

    Part 1: Internet Crime Investigations; International audience; Determining the source of criminal activity requires a reliable means to estimate a criminal’s identity. One way to do this is to use web browsing history to build a profile of an anonymous user. Since an individual’s web use is unique, matching the web use profile to known samples provides a means to identify an unknown user. This paper describes a model for web user profiling and identification. Two aspects of browsing behavior ...

  6. Improving Organizational Citizenship Behavior based on Flow Experience

    Directory of Open Access Journals (Sweden)

    Alecxandrina Deaconu

    2016-07-01

    Full Text Available Building on previous research on Organizational Citizenship Behavior (OCB and its influence on the performance of SMEs, this article intends to expand the investigation area to the concept of Flow and its relationship with OCB. In this paper we performed an analysis of the two theoretical constructs, we highlighted similarities and complementarities and we formulated arguments supporting the need to implement strategies that promote a state of flow. Our study points out that through these strategies, employees are encouraged to perform an extra role, beyond their formal duties, which generates an increase of OCB and favorable conditions for sustainable development.

  7. The health indicators associated with screen-based sedentary behavior among adolescent girls: a systematic review.

    Science.gov (United States)

    Costigan, Sarah A; Barnett, Lisa; Plotnikoff, Ronald C; Lubans, David R

    2013-04-01

    Evidence suggests sitting time is independently associated with a range of health issues in adults, yet the relationship between sedentary behavior and health indicators in young people is less clear. Age-related increases in sedentary behavior are well-documented; the behavioral patterns of adolescent girls are of particular concern. More than one third of adolescent girls' sedentary behavior time is accumulated through use of recreational screen-based behaviors. The objective of this review was to investigate the association between recreational screen-based sedentary behavior and the physical, behavioral, and psychosocial health indicators for adolescent girls. A secondary objective was to identify studies that have adjusted sedentary behavior indicators for physical activity. A structured electronic search of all publication years (through December 2011) was conducted to identify studies in: CINAHL, Communications and Mass Media Complete, ERIC, MEDLINE with Full Text, PsycINFO, and SPORTDiscus with Full Text. Included publications were observational and interventional studies involving adolescent girls (12-18 years) that examined associations between screen-based, sedentary behavior and health indicators (physical, psychosocial, and/or behavioral). The search identified 33 studies that evaluated health indicators of screen-based sedentary behaviors among adolescent girls. Strong evidence for a positive association between screen-based sedentary behavior and weight status was found. A positive association was observed between screen-time and sleep problems, musculoskeletal pain and depression. Negative associations were identified between screen time and physical activity/fitness, screen time and psychological well-being, and screen time and social support. The relationship between screen-based sedentary behavior and diet quality was inconclusive. Less than half of the studies adjusted sedentary behavior indicators for physical activity. Screen-based sedentary

  8. Frontal lobe activation during object permanence: data from near-infrared spectroscopy.

    Science.gov (United States)

    Baird, Abigail A; Kagan, Jerome; Gaudette, Thomas; Walz, Kathryn A; Hershlag, Natalie; Boas, David A

    2002-08-01

    The ability to create and hold a mental schema of an object is one of the milestones in cognitive development. Developmental scientists have named the behavioral manifestation of this competence object permanence. Convergent evidence indicates that frontal lobe maturation plays a critical role in the display of object permanence, but methodological and ethical constrains have made it difficult to collect neurophysiological evidence from awake, behaving infants. Near-infrared spectroscopy provides a noninvasive assessment of changes in oxy- and deoxyhemoglobin and total hemoglobin concentration within a prescribed region. The evidence described in this report reveals that the emergence of object permanence is related to an increase in hemoglobin concentration in frontal cortex.

  9. Diagnostics Systems for Permanent Hall Thrusters Development

    Science.gov (United States)

    Ferreira, Jose Leonardo; Soares Ferreira, Ivan; Santos, Jean; Miranda, Rodrigo; Possa, M. Gabriela

    This work describes the development of Permanent Magnet Hall Effect Plasma Thruster (PHALL) and its diagnostic systems at The Plasma Physics Laboratory of University of Brasilia. The project consists on the construction and characterization of plasma propulsion engines based on the Hall Effect. Electric thrusters have been employed in over 220 successful space missions. Two types stand out: the Hall-Effect Thruster (HET) and the Gridded Ion Engine (GIE). The first, which we deal with in this project, has the advantage of greater simplicity of operation, a smaller weight for the propulsion subsystem and a longer shelf life. It can operate in two configurations: magnetic layer and anode layer, the difference between the two lying in the positioning of the anode inside the plasma channel. A Hall-Effect Thruster-HET is a type of plasma thruster in which the propellant gas is ionized and accelerated by a magneto hydrodynamic effect combined with electrostatic ion acceleration. So the essential operating principle of the HET is that it uses a J x B force and an electrostatic potential to accelerate ions up to high speeds. In a HET, the attractive negative charge is provided by electrons at the open end of the Thruster instead of a grid, as in the case of the electrostatic ion thrusters. A strong radial magnetic field is used to hold the electrons in place, with the combination of the magnetic field and the electrostatic potential force generating a fast circulating electron current, the Hall current, around the axis of the Thruster, mainly composed by drifting electrons in an ion plasma background. Only a slow axial drift towards the anode occurs. The main attractive features of the Hall-Effect Thruster are its simple design and operating principles. Most of the Hall-Effect Thrusters use electromagnet coils to produce the main magnetic field responsible for plasma generation and acceleration. In this paper we present a different new concept, a Permanent Magnet Hall

  10. Corporate Policies with Permanent and Transitory Shocks

    NARCIS (Netherlands)

    J-P. Decamps (Jean-Paul); S. Gryglewicz (Sebastian); E. Morellec (Erwan); S. Villeneuve (Stephane)

    2016-01-01

    textabstractWe model the financing, cash holdings, and hedging policies of a firm facing financing frictions and subject to permanent and transitory cash flow shocks. We show that permanent and transitory shocks generate distinct, sometimes opposite, effects on corporate policies and use the model

  11. OAS :: Authorities : Permanent Representatives to the OAS

    Science.gov (United States)

    Rights Actions against Corruption C Children Civil Registry Civil Society Contact Us Culture Cyber Representative of Belize Diego Pary Rodríguez Bolivia Diego Pary Rodríguez Ambassador, Permanent Representative of Bolivia José Luiz Machado Brazil José Luiz Machado e Costa Ambassador, Permanent Representative

  12. Leadership in a (permanent) crisis.

    Science.gov (United States)

    Heifetz, Ronald; Grashow, Alexander; Linsky, Marty

    2009-01-01

    The current economic crisis is not just another rough spell. Today's mix of urgency, high stakes, and uncertainty will continue even after the recession ends. The immediate crisis--which we will get through with policy makers' expert technical adjustments--sets the stage for a sustained, or even permanent, crisis, a relentless series of challenges no one has encountered before. Instead of hunkering down and relying on their familiar expertise to deal with the sustained crisis, people in positions of authority--whether they are CEOs or managers heading up a company initiative--must practice what the authors call adaptive leadership. They must, of course, tackle the underlying causes of the crisis, but they must also simultaneously make the changes that will allow their organizations to thrive in turbulent environments. Adaptive leadership is an improvisational and experimental art, requiring some new practices. Like Julie Gilbert, who overcame internal resistance to reorient Best Buy toward female purchasers, adaptive leaders get things done to meet today's challenges and then modify those things to thrive in tomorrow's world. They also embrace disequilibrium, using turbulence as an opportunity to build crucial new capacities, as Paul Levy did to rescue Beth Israel Deaconess Medical Center from a profound financial crisis. Finally, adaptive leaders, such as Egon Zehnder, the founder of an executive search firm, draw out the leadership skills that reside deep in the organization, recognizing the interdependence of all employees and mobilizing everyone to generate solutions.

  13. Guidelines for removing permanent makeup

    Directory of Open Access Journals (Sweden)

    C.Bettina Rümmelein

    2016-09-01

    Full Text Available Permanent makeup (PMU is a frequently implemented cosmetic procedure performed by beauticians. From a technical point, PMU is considered a facial tattoo. Failed procedures or a change of mind can lead to the desire for removal. The purpose of this retrospective evaluation of patients who came to the clinic with the desire to remove PMU between 2011 and 2015 was to explore the problems, side effects, and results in order to define treatment guidelines for other doctors. We evaluated 87 individual cases in total. In treatable cases, i.e. 52 out of the 87 cases, laser treatments were performed using a nanosecond Q-switched neodymium-doped yttrium aluminium garnet (Nd:YAG laser. It takes between 1-12 treatments to remove the PMU. In three cases, the colour of the PMU could not be removed by laser and remained after the treatment. In two cases, laser treatment had to be terminated due to colour changes towards the green-blue spectrum. Before PMU removal, laser test shots are urgently recommended as unforeseeable colour changes can cause severe aesthetically unpleasant results. Covered up PMU (skin colour is particularly susceptible to changes in colour. Heat-induced shrinking of the eye area can cause an ectropium. Surgical solutions also have to be taken into consideration. The use of proper eye protection with intraocular eye shields is mandatory. This article is an attempt to set up some guidelines for the treatment of PMU removal.

  14. Behavior of gadolinium-based diagnostics in water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Cyris, Maike

    2013-04-25

    determined, however, it is strongly assumed that the anthropogenic gadolinium fraction is present as chelate. Adsorption characteristics were evaluated by bottle point isotherm experiments on different activated carbon types and activated polymer based sorbents. The Freundlich coefficients vary between 0.013 and 2.83 (μmol kg{sup -1})(L μmol{sup -1}){sup 1/n} for Gd-BT-DO3A, on Chemviron RD 90 {sup registered} and on the best synthetic adsorbent, respectively. Lab scale experiments with small adsorber columns in a drinking water matrix gave insight in the behavior during fixed-bed adsorption processes. The breakthrough was described successfully by the Linear Driving Force model. Modeling has shown that a description of experimental results is only possible by including dissolved organic carbon isotherm results from drinking water in the model, to describe an additional competitive adsorption effect within the fixed-bed adsorber, different from direct competition. First investigations in a wastewater treatment plant proved a poor adsorption of gadolinium similar to iodinated X-ray contrast media such as iopamidole. Therefore, gadolinium will hardly be removed from wastewater by implementation of a further adsorptive treatment step. However, gadolinium may be utilized as indicator substance for breakthrough. Rate constants of the chelates with ozone and hydroxyl radicals have been determined under pseudo-first-order conditions. Rate constants for the ozone reaction were determined to be < 50 M{sup -1}s{sup -1} for all tested chelates. Hence, the chelates may be considered ozone refractory. For determination of hydroxyl radical rate constants different methods were applied. Radicals were generated either by pulse radiolysis, in this case rate constant were determined directly and by competition with thiocyanate, or by the peroxone process, where only competition kinetics were applied (para-chlorobenzoic acid and tert-butanol as competitors). From pulse radiolysis

  15. Behavior of gadolinium-based diagnostics in water treatment

    International Nuclear Information System (INIS)

    Cyris, Maike

    2013-01-01

    , however, it is strongly assumed that the anthropogenic gadolinium fraction is present as chelate. Adsorption characteristics were evaluated by bottle point isotherm experiments on different activated carbon types and activated polymer based sorbents. The Freundlich coefficients vary between 0.013 and 2.83 (μmol kg -1 )(L μmol -1 ) 1/n for Gd-BT-DO3A, on Chemviron RD 90 registered and on the best synthetic adsorbent, respectively. Lab scale experiments with small adsorber columns in a drinking water matrix gave insight in the behavior during fixed-bed adsorption processes. The breakthrough was described successfully by the Linear Driving Force model. Modeling has shown that a description of experimental results is only possible by including dissolved organic carbon isotherm results from drinking water in the model, to describe an additional competitive adsorption effect within the fixed-bed adsorber, different from direct competition. First investigations in a wastewater treatment plant proved a poor adsorption of gadolinium similar to iodinated X-ray contrast media such as iopamidole. Therefore, gadolinium will hardly be removed from wastewater by implementation of a further adsorptive treatment step. However, gadolinium may be utilized as indicator substance for breakthrough. Rate constants of the chelates with ozone and hydroxyl radicals have been determined under pseudo-first-order conditions. Rate constants for the ozone reaction were determined to be < 50 M -1 s -1 for all tested chelates. Hence, the chelates may be considered ozone refractory. For determination of hydroxyl radical rate constants different methods were applied. Radicals were generated either by pulse radiolysis, in this case rate constant were determined directly and by competition with thiocyanate, or by the peroxone process, where only competition kinetics were applied (para-chlorobenzoic acid and tert-butanol as competitors). From pulse radiolysis determinations (rate constants > 10 9 M -1 s -1

  16. A Model-Based Approach to Engineering Behavior of Complex Aerospace Systems

    Science.gov (United States)

    Ingham, Michel; Day, John; Donahue, Kenneth; Kadesch, Alex; Kennedy, Andrew; Khan, Mohammed Omair; Post, Ethan; Standley, Shaun

    2012-01-01

    One of the most challenging yet poorly defined aspects of engineering a complex aerospace system is behavior engineering, including definition, specification, design, implementation, and verification and validation of the system's behaviors. This is especially true for behaviors of highly autonomous and intelligent systems. Behavior engineering is more of an art than a science. As a process it is generally ad-hoc, poorly specified, and inconsistently applied from one project to the next. It uses largely informal representations, and results in system behavior being documented in a wide variety of disparate documents. To address this problem, JPL has undertaken a pilot project to apply its institutional capabilities in Model-Based Systems Engineering to the challenge of specifying complex spacecraft system behavior. This paper describes the results of the work in progress on this project. In particular, we discuss our approach to modeling spacecraft behavior including 1) requirements and design flowdown from system-level to subsystem-level, 2) patterns for behavior decomposition, 3) allocation of behaviors to physical elements in the system, and 4) patterns for capturing V&V activities associated with behavioral requirements. We provide examples of interesting behavior specification patterns, and discuss findings from the pilot project.

  17. Approaches based on behavioral economics could help nudge patients and providers toward lower health spending growth.

    Science.gov (United States)

    King, Dominic; Greaves, Felix; Vlaev, Ivo; Darzi, Ara

    2013-04-01

    Policies that change the environment or context in which decisions are made and "nudge" people toward particular choices have been relatively ignored in health care. This article examines the role that approaches based on behavioral economics could play in "nudging" providers and patients in ways that could slow health care spending growth. The basic insight of behavioral economics is that behavior is guided by the very fallible human brain and greatly influenced by the environment or context in which choices are made. In policy arenas such as pensions and personal savings, approaches based on behavioral economics have provided notable results. In health care, such approaches have been used successfully but in limited ways, as in the use of surgical checklists that have increased patient safety and reduced costs. With health care spending climbing at unsustainable rates, we review the role that approaches based on behavioral economics could play in offering policy makers a potential set of new tools to slow spending growth.

  18. A Dynamic Object Behavior Model and Implementation Based on Computational Reflection

    Institute of Scientific and Technical Information of China (English)

    HE Cheng-wan; HE Fei; HE Ke-qing

    2005-01-01

    A dynamic object behavior model based on computational reflection is proposed. This model consists of function level and meta level, the meta objects in meta level manage the base objects and behaviors in function level, including dynamic binding and unbinding of base object and behavior.We implement this model with RoleJava Language, which is our self linguistic extension of the Java Language. Meta Objects are generated automatically at compile-time, this makes the reflecton mechanism transparent to programmers. Finally an example applying this model to a banking system is presented.

  19. Simulation Study of Swarm Intelligence Based on Life Evolution Behavior

    Directory of Open Access Journals (Sweden)

    Yanmin Liu

    2015-01-01

    Full Text Available Swarm intelligence (SI is a new evolutionary computation technology, and its performance efficacy is usually affected by each individual behavior in the swarm. According to the genetic and sociological theory, the life evolution behavior process is influenced by the external and internal factors, so the mechanisms of external and internal environment change must be analyzed and explored. Therefore, in this paper, we used the thought of the famous American genetic biologist Morgan, “life = DNA + environment + interaction of environment + gene,” to propose the mutation and crossover operation of DNA fragments by the environmental change to improve the performance efficiency of intelligence algorithms. Additionally, PSO is a random swarm intelligence algorithm with the genetic and sociological property, so we embed the improved mutation and crossover operation to particle swarm optimization (PSO and designed DNA-PSO algorithm to optimize single and multiobjective optimization problems. Simulation experiments in single and multiobjective optimization problems show that the proposed strategies can effectively improve the performance of swarm intelligence.

  20. Thermal Behavior of Tacca leontopetaloides Starch-Based Biopolymer

    Directory of Open Access Journals (Sweden)

    Nurul Shuhada Mohd Makhtar

    2013-01-01

    Full Text Available Starch is used whenever there is a need for natural elastic properties combined with low cost of production. However, the hydrophilic properties in structural starch will decrease the thermal performance of formulated starch polymer. Therefore, the effect of glycerol, palm olein, and crude palm oil (CPO, as plasticizers, on the thermal behavior of Tacca leontopetaloides starch incorporated with natural rubber in biopolymer production was investigated in this paper. Four different formulations were performed and represented by TPE1, TPE2, TPE3, and TPE4. The compositions were produced by using two-roll mill compounding. The sheets obtained were cut into small sizes prior to thermal testing. The addition of glycerol shows higher enthalpy of diffusion in which made the material easily can be degraded, leaving to an amount of 6.6% of residue. Blending of CPO with starch (TPE3 had a higher thermal resistance towards high temperature up to 310°C and the thermal behavior of TPE2 only gave a moderate performance compared with other TPEs.

  1. Measuring Permanent Responses to Capital-Gains Tax Changes in Panel Data.

    OpenAIRE

    Burman, Leonard E; Randolph, William C

    1994-01-01

    The authors use panel data and information about differences in state tax rates to separate the effects of transitory and permanent tax rate changes on capital-gains realizations behavior. The estimated effect of permanent change is substantially smaller than the effect of transitory change. The difference is even larger than differences between estimates from past micro data studies, which have primarily measured the transitory effect, and time-series studies, which have primarily measured t...

  2. The Effect of Emotional Feedback on Behavioral Intention to Use Computer Based Assessment

    Science.gov (United States)

    Terzis, Vasileios; Moridis, Christos N.; Economides, Anastasios A.

    2012-01-01

    This study introduces emotional feedback as a construct in an acceptance model. It explores the effect of emotional feedback on behavioral intention to use Computer Based Assessment (CBA). A female Embodied Conversational Agent (ECA) with empathetic encouragement behavior was displayed as emotional feedback. More specifically, this research aims…

  3. Evaluating a School-Based Day Treatment Program for Students with Challenging Behaviors

    Science.gov (United States)

    Hickman, Antoine Lewis

    2014-01-01

    Jade County Public Schools has provided school-based therapeutic day treatment in its public schools for more than 10 years. This program was adopted by the school system to provide an intervention in the school and classroom to address the challenging behaviors of students with emotional and behavioral disorders. Currently, three human services…

  4. Responsible Adult Culture (RAC): Cognitive and Behavioral Changes at a Community-Based Correctional Facility

    Science.gov (United States)

    Devlin, Renee S.; Gibbs, John C.

    2010-01-01

    This article examined cognitive and behavioral changes among participants in Responsible Adult Culture (RAC), a cognitive-behavioral (especially, cognitive restructuring) treatment program in use at the Franklin County Community-Based Correctional Facility (CBCF). Participants were adult felony offenders (approximately three-fourths male). A…

  5. Young Adolescents' Gender-, Ethnicity-, and Popularity-Based Social Schemas of Aggressive Behavior

    Science.gov (United States)

    Clemans, Katherine H.; Graber, Julia A.

    2016-01-01

    Social schemas can influence the perception and recollection of others' behavior and may create biases in the reporting of social events. This study investigated young adolescents' (N = 317) gender-, ethnicity-, and popularity-based social schemas of overtly and relationally aggressive behavior. Results indicated that participants associated overt…

  6. Teachers' Reported Knowledge and Implementation of Research-Based Classroom and Behavior Management Strategies

    Science.gov (United States)

    Moore, Tara C.; Wehby, Joseph H.; Oliver, Regina M.; Chow, Jason C.; Gordon, Jason R.; Mahany, Laura A.

    2017-01-01

    Teachers' reported knowledge about and implementation of research-based classroom and behavior management strategies were examined. A total of 160 elementary teachers from two districts in different regions of the same state completed the researcher-developed "Survey of Classroom and Behavior Management." On average, teachers reported to…

  7. Early Career Teacher Professional Development: Bridging Simulation Technology with Evidence-Based Behavior Management

    Science.gov (United States)

    Shernoff, Elisa; Frazier, Stacy; Lisetti, Christine; Buche, Cedric; Lunn, Stephanie; Brown, Claire; Delmarre, Alban; Chou, Tommy; Gabbard, Joseph; Morgan, Emily

    2018-01-01

    Early career teachers working in high poverty schools face of overwhelming challenges navigating disruptive behaviors with studies highlighting behavior problems as one of the strongest predictors of turnover (Ingersoll & Smith, 2003). Simulation-based technology leverages important pedagogical strengths (e.g., realistic training context,…

  8. The Effects of a School-Based Functional Analysis on Subsequent Classroom Behavior

    Science.gov (United States)

    Davis, Tonya N.; Durand, Shannon; Fuentes, Lisa; Dacus, Sharon; Blenden, Kara

    2014-01-01

    In this study we analyzed the effects of conducting a school-based functional analysis on subsequent classroom behavior. Each participant was observed in the classroom during activities that were reported by teachers to result in high levels of challenging behavior. Participants were observed during (a) baseline, prior to the administration of a…

  9. Training Head Start Teachers to Conduct Trial-Based Functional Analysis of Challenging Behavior

    Science.gov (United States)

    Rispoli, Mandy; Burke, Mack D.; Hatton, Heather; Ninci, Jennifer; Zaini, Samar; Sanchez, Lisa

    2015-01-01

    Trial-based functional analysis (TBFA) is a procedure for experimentally identifying the function of challenging behavior within applied settings. The purpose of this study was to examine the effects of a TBFA teacher-training package in the context of two Head Start centers implementing programwide positive behavior support (PWPBS). Four Head…

  10. Predicting Study Abroad Intentions Based on the Theory of Planned Behavior

    Science.gov (United States)

    Schnusenberg, Oliver; de Jong, Pieter; Goel, Lakshmi

    2012-01-01

    The emphasis on study abroad programs is growing in the academic context as U.S. based universities seek to incorporate a global perspective in education. Using a model that has underpinnings in the theory of planned behavior (TPB), we predict students' intention to participate in short-term study abroad program. We use TPB to identify behavioral,…

  11. Gender-Based Behavioral Analysis for End-User Development and the "RULES" Attributes

    Science.gov (United States)

    Tzafilkou, Katerina; Protogeros, Nicolaos; Karagiannidis, Charalampos; Koumpis, Adamantios

    2017-01-01

    This paper addresses the role of gender in End-User Development (EUD) environments and examines whether there are gender differences in performance and in correlations between performance and a set of behavioral attributes. Based on a review of the most prominent EUD-related behavioral Human Computer Interaction (HCI) theories, and the influence…

  12. Effects of Interventions Based on Health Behavior Models on Breast Cancer Screening Behaviors of Migrant Women in Turkey.

    Science.gov (United States)

    Tuzcu, Ayla; Bahar, Zuhal; Gözüm, Sebahat

    2016-01-01

    Antalya is a city receiving internal and external migration in Turkey, including migrant women in need of developing breast cancer screening behaviors. The aim of this study was to develop breast cancer screening behaviors of migrant women through nursing interventions based on the Health Belief Model and the Health Promotion Model. This quasi-experimental study was conducted with 200 women (100 women in the intervention group, 100 women in the control group) in Antalya. The intervention group received training, consultancy service, and reminders and was followed up at 3 and 6 months after interventions. The rates of breast self-examination, clinical breast examination and mammography were higher at months 3 and 6 in women in the intervention group compared with the women in the control group. In the intervention group, perceptions of susceptibility and barriers decreased after the interventions, and benefit, health motivation, and self-efficacy perceptions increased. According to month 6 data, in the intervention group, the decrease of each unit in perception of barriers increased the rate of breast self-examination 0.8 times and the rate of mammography 0.7 times. An increase of each unit in health motivation increased the rate of clinical breast examination 1.3 times and the rate of mammography 1.5 times. Interventions based on health behavior models positively affected breast cancer screening behaviors of migrant women. Health motivations and perceptions of barriers are determinants in performing the screening behaviors. Migrant women should be supported more by healthcare professionals regarding recognition of breast health and disease and in transportation to screening centers in their new location.

  13. Concepts and Models Regarding the Behavior of Antiseismic Devices for the Base Isolation System

    Directory of Open Access Journals (Sweden)

    Polidor BRATU

    2013-07-01

    Full Text Available The paper presents the main antiseismic devices, as component elements of the base isolation systems, in such a manner that the functional and constructive parameters are correlated with the inertial and stiffness characteristics of the dynamic isolated building. Also, each device will be characterized through a rheological model, which conditions the eigenvalues and eigenvectors spectrum, as well as the dynamic response to an exterior excitation of a seismic nature. In this context, antiseismic devices defined and characterized by the European Standard EN 15129 will be presented. Based on the requirements formulated in the norm, the devices can be identified and their laws of evolution established and checked as follows: antiseismic devices with permanent rigid connection; antiseismic devices with rigid connections with respect to the instantaneous displacement and antiseismic devices dependent on the velocity and on the velocity variation in time.

  14. Antecedents of employee electricity saving behavior in organizations: An empirical study based on norm activation model

    International Nuclear Information System (INIS)

    Zhang, Yixiang; Wang, Zhaohua; Zhou, Guanghui

    2013-01-01

    China is one of the major energy-consuming countries, and is under great pressure to promote energy saving and reduce domestic energy consumption. Employees constitute an important target group for energy saving. However, only a few research efforts have been paid to study what drives employee energy saving behavior in organizations. To fill this gap, drawing on norm activation model (NAM), we built a research model to study antecedents of employee electricity saving behavior in organizations. The model was empirically tested using survey data collected from office workers in Beijing, China. Results show that personal norm positively influences employee electricity saving behavior. Organizational electricity saving climate negatively moderates the effect of personal norm on electricity saving behavior. Awareness of consequences, ascription of responsibility, and organizational electricity saving climate positively influence personal norm. Furthermore, awareness of consequences positively influences ascription of responsibility. This paper contributes to the energy saving behavior literature by building a theoretical model of employee electricity saving behavior which is understudied in the current literature. Based on the empirical results, implications on how to promote employee electricity saving are discussed. - Highlights: • We studied employee electricity saving behavior based on norm activation model. • The model was tested using survey data collected from office workers in China. • Personal norm positively influences employee′s electricity saving behavior. • Electricity saving climate negatively moderates personal norm′s effect. • This research enhances our understanding of employee electricity saving behavior

  15. A medical assistant-based program to promote healthy behaviors in primary care.

    Science.gov (United States)

    Ferrer, Robert L; Mody-Bailey, Priti; Jaén, Carlos Roberto; Gott, Sherrie; Araujo, Sara

    2009-01-01

    Most primary care patients have at least 1 major behavioral risk: smoking, risky drinking, low physical activity, or unhealthy diet. We studied the effectiveness of a medical assistant-based program to identify and refer patients with risk behaviors to appropriate interventions. We undertook a randomized control trial in a practice-based research network. The trial included 864 adult patients from 6 primary care practices. Medical assistants screened patients for 4 risk behaviors and applied behavior-specific algorithms to link patients with interventions. Primary outcomes were improved risk behaviors on standardized assessments. Secondary outcomes included participation in a behavioral intervention and the program's effect on the medical assistants' workflow and job satisfaction. Follow-up data were available for 55% of participants at a mean of 12 months. The medical assistant referral arm referred a greater proportion of patients than did usual care (67.4 vs 21.8%; P effects on program adoption. Engaging more primary care team members to address risk behaviors improved referral rates. More extensive medical assistant training, changes in practice culture, and sustained behavioral interventions will be necessary to improve risk behavior outcomes.

  16. Behavioral competence as a positive youth development construct: conceptual bases and implications for curriculum development.

    Science.gov (United States)

    Ma, Hing Keung

    2006-01-01

    Behavioral competence refers to the ability to use non-verbal and verbal strategies to perform socially acceptable and normative behavior in social interactions. The main objective is to teach our children to be courteous, graceful, and fair so that they behave with respect and responsibility in social interactions with others. The importance of behavioral competence is discussed and it is emphasized that the competence to behave or act effectively must be based on a positive or prosocial motivation or disposition. The behavioral program units cover the following three types of behaviors: applause, criticism, and apology. The general goal is to foster the development of socially acceptable character, manner, and normative behavior. This paper is part of the development of the positive youth development program in Hong Kong.

  17. Design and Implementation of Behavior Recognition System Based on Convolutional Neural Network

    Directory of Open Access Journals (Sweden)

    Yu Bo

    2017-01-01

    Full Text Available We build a set of human behavior recognition system based on the convolution neural network constructed for the specific human behavior in public places. Firstly, video of human behavior data set will be segmented into images, then we process the images by the method of background subtraction to extract moving foreground characters of body. Secondly, the training data sets are trained into the designed convolution neural network, and the depth learning network is constructed by stochastic gradient descent. Finally, the various behaviors of samples are classified and identified with the obtained network model, and the recognition results are compared with the current mainstream methods. The result show that the convolution neural network can study human behavior model automatically and identify human’s behaviors without any manually annotated trainings.

  18. Model-based Small Area Estimates of Cancer Risk Factors and Screening Behaviors - Small Area Estimates

    Science.gov (United States)

    These model-based estimates use two surveys, the Behavioral Risk Factor Surveillance System (BRFSS) and the National Health Interview Survey (NHIS). The two surveys are combined using novel statistical methodology.

  19. Evolving dynamics of trading behavior based on coordination game in complex networks

    Science.gov (United States)

    Bian, Yue-tang; Xu, Lu; Li, Jin-sheng

    2016-05-01

    This work concerns the modeling of evolvement of trading behavior in stock markets. Based on the assumption of the investors' limited rationality, the evolution mechanism of trading behavior is modeled according to the investment strategy of coordination game in network, that investors are prone to imitate their neighbors' activity through comprehensive analysis on the risk dominance degree of certain investment behavior, the network topology of their relationship and its heterogeneity. We investigate by mean-field analysis and extensive simulations the evolution of investors' trading behavior in various typical networks under different risk dominance degree of investment behavior. Our results indicate that the evolution of investors' behavior is affected by the network structure of stock market and the effect of risk dominance degree of investment behavior; the stability of equilibrium states of investors' behavior dynamics is directly related with the risk dominance degree of some behavior; connectivity and heterogeneity of the network plays an important role in the evolution of the investment behavior in stock market.

  20. Multi-robot Cooperation Behavior Decision Based on Psychological Values

    Directory of Open Access Journals (Sweden)

    Jian JIANG

    2014-01-01

    Full Text Available The method based on psychology concept has been proved to be a successful tool used for human-robot interaction. But its related research in multi-robot cooperation has remained scarce until recent studies. To solve the problem, a decision-making mechanism based on psychological values is presented to be regarded as the basis of the multi-robot cooperation. Robots give birth to psychological values based on the estimations of environment, teammates and themselves. The mapping relationship between psychological values and cooperation tendency threshold values is set up with artificial neural network. Robots can make decision on the bases of these threshold values in cooperation scenes. Experiments show that the multi-robot cooperation method presented in the paper not only can ensure the rationality of robots’ decision-making, but also can ensure the speediness of robots’ decision-making.

  1. Polyaniline–lead sulfate based cell with supercapattery behavior

    Directory of Open Access Journals (Sweden)

    Alsadek A. Alguail

    2017-07-01

    Full Text Available The electrochemically synthesized polyaniline and lead sulfate are investigated as a possible active material of the aqueous based hybrid asymmetric supercapacitors. The electrochemical characteristics of polyaniline (doping-dedoping reactions, as well as electrical characteristics (specific capacitance, capacity, energy, and power of the PbSO4|PANI cell, are determined. Based on the estimated specific energy and power, it is suggested that investigated cell could be classified as “supercapattery” type of electrochemical power sources.

  2. Health behavior change in advance care planning: an agent-based model

    Directory of Open Access Journals (Sweden)

    Natalie C. Ernecoff

    2016-02-01

    Full Text Available Abstract Background A practical and ethical challenge in advance care planning research is controlling and intervening on human behavior. Additionally, observing dynamic changes in advance care planning (ACP behavior proves difficult, though tracking changes over time is important for intervention development. Agent-based modeling (ABM allows researchers to integrate complex behavioral data about advance care planning behaviors and thought processes into a controlled environment that is more easily alterable and observable. Literature to date has not addressed how best to motivate individuals, increase facilitators and reduce barriers associated with ACP. We aimed to build an ABM that applies the Transtheoretical Model of behavior change to ACP as a health behavior and accurately reflects: 1 the rates at which individuals complete the process, 2 how individuals respond to barriers, facilitators, and behavioral variables, and 3 the interactions between these variables. Methods We developed a dynamic ABM of the ACP decision making process based on the stages of change posited by the Transtheoretical Model. We integrated barriers, facilitators, and other behavioral variables that agents encounter as they move through the process. Results We successfully incorporated ACP barriers, facilitators, and other behavioral variables into our ABM, forming a plausible representation of ACP behavior and decision-making. The resulting distributions across the stages of change replicated those found in the literature, with approximately half of participants in the action-maintenance stage in both the model and the literature. Conclusions Our ABM is a useful method for representing dynamic social and experiential influences on the ACP decision making process. This model suggests structural interventions, e.g. increasing access to ACP materials in primary care clinics, in addition to improved methods of data collection for behavioral studies, e.g. incorporating

  3. Health behavior change in advance care planning: an agent-based model.

    Science.gov (United States)

    Ernecoff, Natalie C; Keane, Christopher R; Albert, Steven M

    2016-02-29

    A practical and ethical challenge in advance care planning research is controlling and intervening on human behavior. Additionally, observing dynamic changes in advance care planning (ACP) behavior proves difficult, though tracking changes over time is important for intervention development. Agent-based modeling (ABM) allows researchers to integrate complex behavioral data about advance care planning behaviors and thought processes into a controlled environment that is more easily alterable and observable. Literature to date has not addressed how best to motivate individuals, increase facilitators and reduce barriers associated with ACP. We aimed to build an ABM that applies the Transtheoretical Model of behavior change to ACP as a health behavior and accurately reflects: 1) the rates at which individuals complete the process, 2) how individuals respond to barriers, facilitators, and behavioral variables, and 3) the interactions between these variables. We developed a dynamic ABM of the ACP decision making process based on the stages of change posited by the Transtheoretical Model. We integrated barriers, facilitators, and other behavioral variables that agents encounter as they move through the process. We successfully incorporated ACP barriers, facilitators, and other behavioral variables into our ABM, forming a plausible representation of ACP behavior and decision-making. The resulting distributions across the stages of change replicated those found in the literature, with approximately half of participants in the action-maintenance stage in both the model and the literature. Our ABM is a useful method for representing dynamic social and experiential influences on the ACP decision making process. This model suggests structural interventions, e.g. increasing access to ACP materials in primary care clinics, in addition to improved methods of data collection for behavioral studies, e.g. incorporating longitudinal data to capture behavioral dynamics.

  4. Social and Behavioral Aspects of a Tag-Based Recommender System

    DEFF Research Database (Denmark)

    Durao, Frederico; Dolog, Peter

    2009-01-01

    Collaborative tagging has emerged as a useful means to organize and share resources on the Web. Recommender systems have been utilized tags for identifying similar resources and generate personalized recommendations. In this paper, we analyze social and behavioral aspects of a tag-based recommender...... system which suggests similar Web pages based on the similarity of their tags. Tagging behavior and language anomalies in tagging activities are some aspects examined from an experiment involving 38 people from 12 countries....

  5. Sensory-Based Intervention for Children with Behavioral Problems: A Systematic Review

    Science.gov (United States)

    Wan Yunus, Farahiyah; Liu, Karen P.; Bissett, Michelle; Penkala, Stefania

    2015-01-01

    Sensory-based intervention is a common approach used to address behavioral problems in children. Types of sensory-based intervention for children and details of the intervention effectiveness have not been systematically examined. This review examined the effectiveness and ideal types of sensory-based interventions for children with behavioral…

  6. Laptop energy-saving opportunities based on user behaviors

    Energy Technology Data Exchange (ETDEWEB)

    Jones, M.E. Jr; Hung, D.L. [College of Engineering, San Jose State University, One Washington Square, San Jose, CA 95192 (United States); Wei, B.W.Y. [Academic Affairs Division, Chico State University, Kendall Hall 106, Chico, CA 95929 (United States)

    2013-05-15

    In order to improve the energy efficiency of laptop use and design, it is important to gain knowledge of how laptops are being used in real-world settings. However, the current workload studies have focused on computer-usage patterns of business users, but not those of consumer users. As part of the Green project at ABC University, a pilot study was undertaken to develop and test software tools and methods for monitoring the laptop computer usage of 13 college students for a period of 1 month. This paper describes such tools and methods for monitoring and collecting laptop usage data. It also illustrates how the collected data can be analyzed to obtain high-impact energy usage patterns, which include long idle periods, excessive use of the AC power source, and high backlight levels. These identified high-impact usage patterns, if confirmed by our subsequent study, offer valuable user behavioral insights to advance more energy-efficient laptop use and design.

  7. Discriminating bot accounts based solely on temporal features of microblog behavior

    Science.gov (United States)

    Pan, Junshan; Liu, Ying; Liu, Xiang; Hu, Hanping

    2016-05-01

    As the largest microblog service in China, Sina Weibo has attracted numerous automated applications (known as bots) due to its popularity and open architecture. We classify the active users from Sina Weibo into human, bot-based and hybrid groups based solely on the study of temporal features of their posting behavior. The anomalous burstiness parameter and time-interval entropy value are exploited to characterize automation. We also reveal different behavior patterns among the three types of users regarding their reposting ratio, daily rhythm and active days. Our findings may help Sina Weibo manage a better community and should be considered for dynamic models of microblog behaviors.

  8. Developing a Behavioral Model for Mobile Phone-Based Diabetes Interventions

    Science.gov (United States)

    Nundy, Shantanu; Dick, Jonathan J.; Solomon, Marla C.; Peek, Monica E.

    2013-01-01

    Objectives Behavioral models for mobile phone-based diabetes interventions are lacking. This study explores the potential mechanisms by which a text message-based diabetes program affected self-management among African-Americans. Methods We conducted in-depth, individual interviews among 18 African-American patients with type 2 diabetes who completed a 4-week text message-based diabetes program. Each interview was audio- taped, transcribed verbatim, and imported into Atlas.ti software. Coding was done iteratively. Emergent themes were mapped onto existing behavioral constructs and then used to develop a novel behavioral model for mobile phone-based diabetes self-management programs. Results The effects of the text message-based program went beyond automated reminders. The constant, daily communications reduced denial of diabetes and reinforced the importance of self-management (Rosenstock Health Belief Model). Responding positively to questions about self-management increased mastery experience (Bandura Self-Efficacy). Most surprisingly, participants perceived the automated program as a “friend” and “support group” that monitored and supported their self-management behaviors (Barrera Social Support). Conclusions A mobile phone-based diabetes program affected self-management through multiple behavioral constructs including health beliefs, self-efficacy, and social support. Practice implications: Disease management programs that utilize mobile technologies should be designed to leverage existing models of behavior change and can address barriers to self-management associated with health disparities. PMID:23063349

  9. Log-linear model based behavior selection method for artificial fish swarm algorithm.

    Science.gov (United States)

    Huang, Zhehuang; Chen, Yidong

    2015-01-01

    Artificial fish swarm algorithm (AFSA) is a population based optimization technique inspired by social behavior of fishes. In past several years, AFSA has been successfully applied in many research and application areas. The behavior of fishes has a crucial impact on the performance of AFSA, such as global exploration ability and convergence speed. How to construct and select behaviors of fishes are an important task. To solve these problems, an improved artificial fish swarm algorithm based on log-linear model is proposed and implemented in this paper. There are three main works. Firstly, we proposed a new behavior selection algorithm based on log-linear model which can enhance decision making ability of behavior selection. Secondly, adaptive movement behavior based on adaptive weight is presented, which can dynamically adjust according to the diversity of fishes. Finally, some new behaviors are defined and introduced into artificial fish swarm algorithm at the first time to improve global optimization capability. The experiments on high dimensional function optimization showed that the improved algorithm has more powerful global exploration ability and reasonable convergence speed compared with the standard artificial fish swarm algorithm.

  10. Log-Linear Model Based Behavior Selection Method for Artificial Fish Swarm Algorithm

    Directory of Open Access Journals (Sweden)

    Zhehuang Huang

    2015-01-01

    Full Text Available Artificial fish swarm algorithm (AFSA is a population based optimization technique inspired by social behavior of fishes. In past several years, AFSA has been successfully applied in many research and application areas. The behavior of fishes has a crucial impact on the performance of AFSA, such as global exploration ability and convergence speed. How to construct and select behaviors of fishes are an important task. To solve these problems, an improved artificial fish swarm algorithm based on log-linear model is proposed and implemented in this paper. There are three main works. Firstly, we proposed a new behavior selection algorithm based on log-linear model which can enhance decision making ability of behavior selection. Secondly, adaptive movement behavior based on adaptive weight is presented, which can dynamically adjust according to the diversity of fishes. Finally, some new behaviors are defined and introduced into artificial fish swarm algorithm at the first time to improve global optimization capability. The experiments on high dimensional function optimization showed that the improved algorithm has more powerful global exploration ability and reasonable convergence speed compared with the standard artificial fish swarm algorithm.

  11. Mindfulness-Based Interventions for Obesity-Related Eating Behaviors: A Literature Review

    Science.gov (United States)

    O’Reilly, Gillian A.; Cook, Lauren; Spruijt-Metz, Donna; Black, David S.

    2014-01-01

    Mindfulness-based interventions (MBIs) targeting eating behaviors have gained popularity in recent years. A literature review was conducted to determine the effectiveness of MBIs for treating obesity-related eating behaviors, such as binge eating, emotional eating, and external eating. A search protocol was conducted using the online databases Google Scholar, PubMed, PsycINFO, and Ovid Healthstar. Articles were required to meet the following criteria to be included in this review: (1) describe a MBI or the use of mindfulness exercises as part of an intervention, (2) include at least one obesity-related eating behavior as an outcome, (3) include quantitative outcomes, and (4) be published in English in a peer-reviewed journal. A total of N=21 articles were included in this review. Interventions used a variety of approaches to implement mindfulness training, including combined mindfulness and cognitive behavioral therapies, mindfulness-based stress reduction, acceptance-based therapies, mindful eating programs, and combinations of mindfulness exercises. Targeted eating behavior outcomes included binge eating, emotional eating, external eating, and dietary intake. Eighteen (86%) of the reviewed studies reported improvements in the targeted eating behaviors. Overall, the results of this first review on the topic support the efficacy of mindfulness-based interventions for changing obesity-related eating behaviors, specifically binge eating, emotional eating, and external eating. PMID:24636206

  12. Pullout behavior of steel fibers from cement-based composites

    DEFF Research Database (Denmark)

    Shannag, M. Jamal; Brincker, Rune; Hansen, Will

    1997-01-01

    A comprehensive experimental program on pullout tests of steel fibers from cement based matrices is described. A specially designed single fiber pullout apparatus was used to provide a quantitative determination of interfacial properties that are relevant to toughening brittle materials through...... fiber reinforcement. The parameters investigated included a specially designed high strength cement based matrix called Densified Small Particles system (DSP), a conventional mortar matrix, fiber embeddment length, and the fiber volume fraction. The mediums from which the fiber was pulled included...... fraction in the cement matrix increase the peak pullout load and the pullout work. (3) The major bond mechanism in both systems is frictional sliding. ...

  13. Permanent multipole magnets with adjustable strength

    International Nuclear Information System (INIS)

    Halbach, K.

    1983-01-01

    Preceded by a short discussion of the motives for using permanent magnets in accelerators, a new type of permanent magnet for use in accelerators is presented. The basic design and most important properties of a quadrople will be described that uses both steel and permanent magnet material. The field gradient produced by this magnet can be adjusted without changing any other aspect of the field produced by this quadrupole. The generalization of this concept to produce other multipole fields, or combination of multipole fields, will also be presented

  14. Nanocrystalline permanent magnets with enhanced properties

    International Nuclear Information System (INIS)

    Leonowicz, M.

    2002-01-01

    Parameters of permanent magnets result from the combination of intrinsic properties such as saturation magnetization, magnetic exchange, and magnetocrystalline energy, as well as microstructural parameters such as phase structure, grain size, and orientation. Reduction of grain size into nanocrystalline regime (∼ 50 nm) leads to the enhanced remanence which derives from ferromagnetic exchange coupling between highly refined grains. In this study the fundamental phenomena, quantities, and structure parameters, which define nanophase permanent magnets are presented and discussed. The theoretical considerations are confronted with experimental data for nanocrystalline Sm-Fe-N type permanent magnets. (author)

  15. Permanent molars: Delayed development and eruption

    Directory of Open Access Journals (Sweden)

    Arathi R

    2006-05-01

    Full Text Available Delayed development and eruption of all the permanent molars is a rare phenomenon, which can cause disturbance in the developing occlusion. The eruption of permanent first and second molars is very important for the coordination of facial growth and for providing sufficient occlusal support for undisturbed mastication. In the case described, the first permanent molars were delayed in their development and were seen erupting at the age of nine and a half years. Severe disparity between the left and the right side of the dentition with respect to the rate of development of molars were also present.

  16. Reactor safety review of permanent changes

    International Nuclear Information System (INIS)

    Lam, K.F.

    1997-01-01

    Operational compliance engineers review all changes as part of a change control process. Each change, permanent or temporary, is required to undergo an intricate review process to ensure that the benefits associated with the change outweigh the risk. For permanent changes, it is necessary to ensure that the proposed design meets the nuclear safety requirements, conforms to the licensing requirements and complies with regulatory requirements. In addition, during installation of the permanent change and prior to in-service, a configuration management process is in place to align the change with operating and maintenance documents. (author)

  17. Permanent multipole magnets with adjustable strength

    International Nuclear Information System (INIS)

    Halbach, K.

    1983-03-01

    Preceded by a short discussion of the motives for using permanent magnets in accelerators, a new type of permanent magnet for use in accelerators is presented. The basic design and most important properties of a quadrupole will be described that uses both steel and permanent magnet material. The field gradient produced by this magnet can be adjusted without changing any other aspect of the field produced by this quadrupole. The generalization of this concept to produce other multipole fields, or combination of multipole fields, will also be presented

  18. Exploring the Effects of Cultural Variables in the Implementation of Behavior-Based Safety in Two Organizations

    Science.gov (United States)

    Bumstead, Alaina; Boyce, Thomas E.

    2005-01-01

    The present case study examines how culture can influence behavior-based safety in different organizational settings and how behavior-based safety can impact different organizational cultures. Behavior-based safety processes implemented in two culturally diverse work settings are described. Specifically, despite identical implementation plans,…

  19. Micromagnetics of rare-earth efficient permanent magnets

    Science.gov (United States)

    Fischbacher, Johann; Kovacs, Alexander; Gusenbauer, Markus; Oezelt, Harald; Exl, Lukas; Bance, Simon; Schrefl, Thomas

    2018-05-01

    The development of permanent magnets containing less or no rare-earth elements is linked to profound knowledge of the coercivity mechanism. Prerequisites for a promising permanent magnet material are a high spontaneous magnetization and a sufficiently high magnetic anisotropy. In addition to the intrinsic magnetic properties the microstructure of the magnet plays a significant role in establishing coercivity. The influence of the microstructure on coercivity, remanence, and energy density product can be understood by using micromagnetic simulations. With advances in computer hardware and numerical methods, hysteresis curves of magnets can be computed quickly so that the simulations can readily provide guidance for the development of permanent magnets. The potential of rare-earth reduced and rare-earth free permanent magnets is investigated using micromagnetic simulations. The results show excellent hard magnetic properties can be achieved in grain boundary engineered NdFeB, rare-earth magnets with a ThMn12 structure, Co-based nano-wires, and L10-FeNi provided that the magnet’s microstructure is optimized.

  20. Object permanence development in infants with motor handicaps.

    Science.gov (United States)

    Fetters, L

    1981-03-01

    This study was an investigation of the effects of a motor handicap on the development of object permanence in the young child. Motor abilities were evaluated for 12 infants aged 13 to 29 months. Based on this evaluation, the children were described as manipulators or nonmanipulators in reference to their upper extremity skills. Their stage of object permanence was assessed using traditional and nontraditional assessments. Heart rate and visual tracking were recorded during the nontraditional assessment. Heart rate did not significantly relate to visual fixation or search response. There was, however, a significant difference (p less than .02) between stage achievement with traditional testing and age-appropriate levels. There was no significant difference between the nontraditional assessment and the age-appropriate levels. In addition, there was no significant difference in the development of object permanence between infants described as manipulators and those described as nonmanipulators. The last two findings suggest that infants with motor handicaps may develop object permanence at the expected ages, according to a nontraditional assessment.

  1. Comparing superconducting and permanent magnets for magnetic refrigeration

    Directory of Open Access Journals (Sweden)

    R. Bjørk

    2016-05-01

    Full Text Available We compare the cost of a high temperature superconducting (SC tape-based solenoid with a permanent magnet (PM Halbach cylinder for magnetic refrigeration. Assuming a five liter active magnetic regenerator volume, the price of each type of magnet is determined as a function of aspect ratio of the regenerator and desired internal magnetic field. It is shown that to produce a 1 T internal field in the regenerator a permanent magnet of hundreds of kilograms is needed or an area of superconducting tape of tens of square meters. The cost of cooling the SC solenoid is shown to be a small fraction of the cost of the SC tape. Assuming a cost of the SC tape of 6000 $/m2 and a price of the permanent magnet of 100 $/kg, the superconducting solenoid is shown to be a factor of 0.3-3 times more expensive than the permanent magnet, for a desired field from 0.5-1.75 T and the geometrical aspect ratio of the regenerator. This factor decreases for increasing field strength, indicating that the superconducting solenoid could be suitable for high field, large cooling power applications.

  2. Permanent Magnetic System Design for the Wall-Climbing Robot

    Directory of Open Access Journals (Sweden)

    W. Shen

    2006-01-01

    Full Text Available This paper presents the design and analysis of the permanent magnetic system for a wall-climbing robot with permanent magnetic tracks. Based on the behaviour of gecko lizards, the architecture of the robot was designed and built, including the structure of the adhesion mechanism, the mechanical architecture and the anti-toppling mechanism. The permanent magnetic adhesion mechanism and the tracked locomotion mechanism were employed in this kind of wall-climbing robot. Through static and dynamic force analysis of the robot under different situations, design requirements for the adhesion mechanism were derived. Two different types of structures were put forward for the permanent magnetic units and are further discussed in this paper. These two types of structures are also analysed in detail. In addition, a finite-element method was used to verify the results of magnetic units. Finally, two wall-climbing robots, equipped with different magnetic systems described previously, are explained and their applications are discussed in this paper.

  3. Detection Model for Seepage Behavior of Earth Dams Based on Data Mining

    Directory of Open Access Journals (Sweden)

    Zhenxiang Jiang

    2018-01-01

    Full Text Available Seepage behavior detecting is an important tool for ensuring the safety of earth dams. However, traditional seepage behavior detection methods have used insufficient monitoring data and have mainly focused on single-point measures and local seepage behavior. The seepage behavior of dams is not quantitatively detected based on the monitoring data with multiple measuring points. Therefore, this study uses data mining techniques to analyze the monitoring data and overcome the above-mentioned shortcomings. The massive seepage monitoring data with multiple points are used as the research object. The key information on seepage behavior is extracted using principal component analysis. The correlation between seepage behavior and upstream water level is described as mutual information. A detection model for overall seepage behavior is established. Result shows that the model can completely extract the seepage monitoring data with multiple points and quantitatively detect the overall seepage behavior of earth dams. The proposed method can provide a new and reasonable means of quantitatively detecting the overall seepage behavior of earth dams.

  4. Corrosion Behavior of Titanium Based Ceramic Coatings Deposited on Steels

    OpenAIRE

    Ali, Rania

    2016-01-01

    Titanium based ceramic films are increasingly used as coating materials because of their high hardness, excellent wear resistance and superior corrosion resistance. Using electrochemical and spectroscopic techniques, the electrochemical properties of different coatings deposited on different steels under different conditions were examined in this study. Thin films of titanium nitride (TiN), titanium diboride (TiB2), and titanium boronitride with different boron concentrations (TiBN-1&2) w...

  5. Intelligent Online Store: User Behavior Analysis based Recommender System

    Directory of Open Access Journals (Sweden)

    Mohamadreza Karimi Alavije

    2015-06-01

    Full Text Available Recommender systems provide personalised recommendations to users, helping them find their ideal items, also play a key role in encouraging users to make their purchases through websites thus leading to the success of online stores. The collaborative filtering method is one of the most successful techniques utilized in these systems facilitating the provision of recommendations close to that of the customer's taste and need. However the proliferation of both customers and products on offer, the technique faces some issues such as "cold start" and scalability. As such in this paper a new method has been introduced in which user-based collaborative filtering is used at a base method along with a weighted clustering of users based upon demographics in order to improve the results obtained from the system. The implementation of the results of the algorithms demonstrate that the presented approach has a lower RMSE, which means that the system offers improved performance and accuracy and that the resulting recommendations are closer to the taste and preferences of the users.

  6. Radiation induced defect flux behaviors at zirconium based component

    International Nuclear Information System (INIS)

    Choi, Sang Il; Kim, Ji Hyun; Kwon, Jun Hyun; Lee, Gyeong Geun

    2013-01-01

    In commercial reactor core, structure materials are located in high temperature and high pressure environment. Therefore, main concern of structure materials is corrosion and mechanical properties change than radiation effects on materials. However, radiation effects on materials become more important phenomena because research reactor condition is different from commercial reactor. The temperature is lower than 100 .deg. C and radiation dose is much higher than that of commercial reactor. Among the radiation effect on zirconium based metal, radiation induced growth (RIG), known as volume conservative distortion, is one of the most important phenomena. Recently, theoretical RIG modeling based on radiation damage theory (RDT) and balance equation are developed. However, these growth modeling have limited framework of single crystal and high temperature. To model theoretical RIG in research reactor, qualitative mechanism must be set up. Therefore, this paper intent is establishing defect flux mechanism of zirconium base metal in research reactor for RIG modeling. After than theoretical RIG work will be expanded to research reactor condition

  7. A Big-Data-based platform of workers' behavior: Observations from the field.

    Science.gov (United States)

    Guo, S Y; Ding, L Y; Luo, H B; Jiang, X Y

    2016-08-01

    Behavior-Based Safety (BBS) has been used in construction to observe, analyze and modify workers' behavior. However, studies have identified that BBS has several limitations, which have hindered its effective implementation. To mitigate the negative impact of BBS, this paper uses a case study approach to develop a Big-Data-based platform to classify, collect and store data about workers' unsafe behavior that is derived from a metro construction project. In developing the platform, three processes were undertaken: (1) a behavioral risk knowledge base was established; (2) images reflecting workers' unsafe behavior were collected from intelligent video surveillance and mobile application; and (3) images with semantic information were stored via a Hadoop Distributed File System (HDFS). The platform was implemented during the construction of the metro-system and it is demonstrated that it can effectively analyze semantic information contained in images, automatically extract workers' unsafe behavior and quickly retrieve on HDFS as well. The research presented in this paper can enable construction organizations with the ability to visualize unsafe acts in real-time and further identify patterns of behavior that can jeopardize safety outcomes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Case Study: Evidence-Based Interventions Enhancing Diabetic Foot Care Behaviors among Hospitalized DM Patients

    Directory of Open Access Journals (Sweden)

    Titis Kurniawan

    2011-01-01

    Full Text Available Background: Improving diabetic patients’ foot care behaviors is one of the most effective strategies in minimizing diabetic foot ulceration and its further negative impacts, either in diabetic hospitalized patients or outpatients.Purpose: To describe foot care knowledge and behaviors among hospitalized diabetic patients, to apply selected foot care knowledge and behaviors improvement evidence, and to evaluate its effectiveness.Method: Four diabetic patients who were under our care for at least three days and could communicate in Thai language were selected from a surgical ward in a university hospital. The authors applied educational program based on patients’ learning needs, provided diabetic foot care leaflet, and assisted patients to set their goal and action plans. In the third day of treatment, we evaluated patients’ foot care knowledge and their goal and action plan statements in improving foot care behaviors.Result: Based on the data collected among four hospitalized diabetic patients, it was shown that all patients needed foot care behaviors improvement and the educational program improved hospitalized patients’ foot care knowledge and their perceived foot care behaviors. The educational program that combined with goal setting and action plans method was easy, safe, and seemed feasibly applicable for diabetic hospitalized patients.Conclusion: The results of this study provide valuable information for improvement of hospitalized diabetic patients’ foot care knowledge and behaviors. The authors recommend nurses to use this evidence-based practice to contribute in improving the quality of diabetic care.Keywords: Intervention, diabetic foot care, hospitalized diabetic patients

  9. Smoking Policy Change Within Permanent Supportive Housing.

    Science.gov (United States)

    Petersen, Anne Berit; Stewart, Holly C; Walters, Jon; Vijayaraghavan, Maya

    2018-04-01

    Smoke-free policies effectively reduce secondhand smoke (SHS) exposure among non-smokers, and reduce consumption, encourage quit attempts, and minimize relapse to smoking among smokers. Such policies are uncommon in permanent supportive housing (PSH) for formerly homeless individuals. In this study, we collaborated with a PSH provider in San Diego, California to assess a smoke-free policy that restricted indoor smoking. Between August and November 2015, residents completed a pre-policy questionnaire on attitudes toward smoke-free policies and exposure to secondhand smoke, and then 7-9 months after policy implementation residents were re-surveyed. At follow-up, there was a 59.7% reduction in indoor smoking. The proportion of residents who identified as current smokers reduced by 13% (95% CI: -38, 10.2). The proportion of residents who reported never smelling SHS indoors (apartment 24.2%, 95% CI: 4.2, 44.1; shared areas 17.2%, 95% CI: 1.7, 32.7); in outdoor areas next to the living unit (porches or patio 56.7%, 95% CI: 40.7, 72.8); and in other outdoor areas (parking lot 28.6%, 95% CI: 8.3, 48.9) was lower post-policy compared with pre-policy. Overall, resident support increased by 18.7%; however, the greatest increase in support occurred among current smokers (from 14.8 to 37.5%). Fewer current smokers reported that the policy would enable cessation at post-policy compared to pre-policy. Our findings demonstrate the feasibility of implementing smoke-free policies in PSH for formerly homeless adults. However, policy alone appears insufficient to trigger change in smoking behavior, highlighting the need for additional cessation resources to facilitate quitting.

  10. Nonuniform radiation damage in permanent magnet quadrupoles.

    Science.gov (United States)

    Danly, C R; Merrill, F E; Barlow, D; Mariam, F G

    2014-08-01

    We present data that indicate nonuniform magnetization loss due to radiation damage in neodymium-iron-boron Halbach-style permanent magnet quadrupoles. The proton radiography (pRad) facility at Los Alamos uses permanent-magnet quadrupoles for magnifying lenses, and a system recently commissioned at GSI-Darmsdadt uses permanent magnets for its primary lenses. Large fluences of spallation neutrons can be produced in close proximity to these magnets when the proton beam is, intentionally or unintentionally, directed into the tungsten beam collimators; imaging experiments at LANL's pRad have shown image degradation with these magnetic lenses at proton beam doses lower than those expected to cause damage through radiation-induced reduction of the quadrupole strength alone. We have observed preferential degradation in portions of the permanent magnet quadrupole where the field intensity is highest, resulting in increased high-order multipole components.

  11. Macroscopic simulation of isotropic permanent magnets

    International Nuclear Information System (INIS)

    Bruckner, Florian; Abert, Claas; Vogler, Christoph; Heinrichs, Frank; Satz, Armin; Ausserlechner, Udo; Binder, Gernot; Koeck, Helmut; Suess, Dieter

    2016-01-01

    Accurate simulations of isotropic permanent magnets require to take the magnetization process into account and consider the anisotropic, nonlinear, and hysteretic material behaviour near the saturation configuration. An efficient method for the solution of the magnetostatic Maxwell equations including the description of isotropic permanent magnets is presented. The algorithm can easily be implemented on top of existing finite element methods and does not require a full characterization of the hysteresis of the magnetic material. Strayfield measurements of an isotropic permanent magnet and simulation results are in good agreement and highlight the importance of a proper description of the isotropic material. - Highlights: • Simulations of isotropic permanent magnets. • Accurate calculation of remanence magnetization and strayfield. • Comparison with strayfield measurements and anisotropic magnet simulations. • Efficient 3D FEM–BEM coupling for solution of Maxwell equations.

  12. Nonuniform radiation damage in permanent magnet quadrupoles

    International Nuclear Information System (INIS)

    Danly, C. R.; Merrill, F. E.; Barlow, D.; Mariam, F. G.

    2014-01-01

    We present data that indicate nonuniform magnetization loss due to radiation damage in neodymium-iron-boron Halbach-style permanent magnet quadrupoles. The proton radiography (pRad) facility at Los Alamos uses permanent-magnet quadrupoles for magnifying lenses, and a system recently commissioned at GSI-Darmsdadt uses permanent magnets for its primary lenses. Large fluences of spallation neutrons can be produced in close proximity to these magnets when the proton beam is, intentionally or unintentionally, directed into the tungsten beam collimators; imaging experiments at LANL’s pRad have shown image degradation with these magnetic lenses at proton beam doses lower than those expected to cause damage through radiation-induced reduction of the quadrupole strength alone. We have observed preferential degradation in portions of the permanent magnet quadrupole where the field intensity is highest, resulting in increased high-order multipole components

  13. Nonuniform radiation damage in permanent magnet quadrupoles

    Energy Technology Data Exchange (ETDEWEB)

    Danly, C. R.; Merrill, F. E.; Barlow, D.; Mariam, F. G. [Los Alamos National Laboratory, Los Alamos, New Mexico 87544 (United States)

    2014-08-15

    We present data that indicate nonuniform magnetization loss due to radiation damage in neodymium-iron-boron Halbach-style permanent magnet quadrupoles. The proton radiography (pRad) facility at Los Alamos uses permanent-magnet quadrupoles for magnifying lenses, and a system recently commissioned at GSI-Darmsdadt uses permanent magnets for its primary lenses. Large fluences of spallation neutrons can be produced in close proximity to these magnets when the proton beam is, intentionally or unintentionally, directed into the tungsten beam collimators; imaging experiments at LANL’s pRad have shown image degradation with these magnetic lenses at proton beam doses lower than those expected to cause damage through radiation-induced reduction of the quadrupole strength alone. We have observed preferential degradation in portions of the permanent magnet quadrupole where the field intensity is highest, resulting in increased high-order multipole components.

  14. Genetics Home Reference: permanent neonatal diabetes mellitus

    Science.gov (United States)

    ... AL. Update on mutations in glucokinase (GCK), which cause maturity-onset diabetes of the young, permanent neonatal diabetes, and hyperinsulinemic hypoglycemia. Hum Mutat. 2009 Nov;30(11):1512-26. ...

  15. Radioelement gauges. Appliances intended for permanent installation

    International Nuclear Information System (INIS)

    1975-08-01

    The present norm defines for radioelement gauges intended for permanent installation: a classification of instruments and beam shutter devices; recommended construction techniques which satisfy health physics requirements; monitoring and test methods; information which must appear on the instruments [fr

  16. Canadian Eskimo permanent tooth emergence timing.

    Science.gov (United States)

    Mayhall, J T; Belier, P L; Mayhall, M F

    1978-08-01

    To identify the times of emergence of the permanent teeth of Canadian Eskimos (Inuit), 368 children and adolescents were examined. The presence or absence of all permanent teeth except the third molars was recorded and these data subjected to probit analysis. Female emergence times were advanced over males. Generally, the Inuit of both sexes showed statistically significant earlier emergence times than Montreal children, except for the incisors. The present results do not support hypotheses indicating that premature extraction of the deciduous teeth advances the emergence of their succedaneous counterparts. There is some indication the controls of deciduous tooth emergence continue to play some part in emergence of the permanent dentition, especially the first permanent teeth that emerge.

  17. Multiple Unerupted Permanent Teeth Associated with Noonan ...

    African Journals Online (AJOL)

    [2] Oral findings in patients with NS include a high arched palate ... the atypical dental anomalies such as multiple unerupted permanent ... clinical features in a child with NS. .... Disabilities, Centers for Disease Control and Prevention (CDC).

  18. Risky music listening, permanent tinnitus and depression, anxiety, thoughts about suicide and adverse general health.

    Science.gov (United States)

    Vogel, Ineke; van de Looij-Jansen, Petra M; Mieloo, Cathelijne L; Burdorf, Alex; de Waart, Frouwkje

    2014-01-01

    To estimate the extent to which exposure to music through earphones or headphones with MP3 players or at discotheques and pop/rock concerts exceeded current occupational safety standards for noise exposure, to examine the extent to which temporary and permanent hearing-related symptoms were reported, and to examine whether the experience of permanent symptoms was associated with adverse perceived general and mental health, symptoms of depression, and thoughts about suicide. A total of 943 students in Dutch inner-city senior-secondary vocational schools completed questionnaires about their sociodemographics, music listening behaviors and health. Multiple logistic regression analyses were used to examine associations. About 60% exceeded safety standards for occupational noise exposure; about one third as a result of listening to MP3 players. About 10% of the participants experienced permanent hearing-related symptoms. Temporary hearing symptoms that occurred after using an MP3 player or going to a discotheque or pop/rock concert were associated with exposure to high-volume music. However, compared to participants not experiencing permanent hearing-related symptoms, those experiencing permanent symptoms were less often exposed to high volume music. Furthermore, they reported at least two times more often symptoms of depression, thoughts about suicide and adverse self-assessed general and mental health. Risky music-listening behaviors continue up to at least the age of 25 years. Permanent hearing-related symptoms are associated with people's health and wellbeing. Participants experiencing such symptoms appeared to have changed their behavior to be less risky. In order to induce behavior change before permanent and irreversible hearing-related symptoms occur, preventive measurements concerning hearing health are needed.

  19. Risky music listening, permanent tinnitus and depression, anxiety, thoughts about suicide and adverse general health.

    Directory of Open Access Journals (Sweden)

    Ineke Vogel

    Full Text Available OBJECTIVE: To estimate the extent to which exposure to music through earphones or headphones with MP3 players or at discotheques and pop/rock concerts exceeded current occupational safety standards for noise exposure, to examine the extent to which temporary and permanent hearing-related symptoms were reported, and to examine whether the experience of permanent symptoms was associated with adverse perceived general and mental health, symptoms of depression, and thoughts about suicide. METHODS: A total of 943 students in Dutch inner-city senior-secondary vocational schools completed questionnaires about their sociodemographics, music listening behaviors and health. Multiple logistic regression analyses were used to examine associations. RESULTS: About 60% exceeded safety standards for occupational noise exposure; about one third as a result of listening to MP3 players. About 10% of the participants experienced permanent hearing-related symptoms. Temporary hearing symptoms that occurred after using an MP3 player or going to a discotheque or pop/rock concert were associated with exposure to high-volume music. However, compared to participants not experiencing permanent hearing-related symptoms, those experiencing permanent symptoms were less often exposed to high volume music. Furthermore, they reported at least two times more often symptoms of depression, thoughts about suicide and adverse self-assessed general and mental health. CONCLUSIONS: Risky music-listening behaviors continue up to at least the age of 25 years. Permanent hearing-related symptoms are associated with people's health and wellbeing. Participants experiencing such symptoms appeared to have changed their behavior to be less risky. In order to induce behavior change before permanent and irreversible hearing-related symptoms occur, preventive measurements concerning hearing health are needed.

  20. Sourcing Team Behavior in Project-Based MNE's

    DEFF Research Database (Denmark)

    Hansen, Anders Peder Lysholm

    2014-01-01

    across the three cases was characterized by conflict between departments represented in the category teams. This resulted in unfortunate sourcing team behaviour and unaligned performance management, which in turn had a number of adverse effects. Further research on how to create a holistic and balanced......This paper presents and discusses a multiple case study of three cross-functional category teams responsible for sourcing critical components within multi-national, project-based enterprises. The study focused on behaviour and management of the sourcing teams and found that the sourcing process...... team perspective in the sourcing teams is suggested....

  1. Behavior of W-based materials in hot helium gas

    Directory of Open Access Journals (Sweden)

    J. Matějíček

    2016-12-01

    A number of W-based materials (pure tungsten and some of its alloys prepared by powder metallurgy techniques was exposed to He atmosphere at 720ºC and 500kPa for 500h. Morphological surface changes were observed by SEM, chemical and phase composition was analyzed by EDS and XRD, respectively. The internal microstructure was observed by a combination of SEM, FIB and TEM techniques. Mechanical properties were determined by instrumented indentation. Some alloys developed a thin oxide layer, in some cases new morphological features were observed, while some samples remained mostly intact. The observed changes are correlated with specific compositions and microstructures.

  2. A Case Study of Positive Behavior Supports-Based Interventions in a Seventh-Grade Urban Classroom

    Science.gov (United States)

    Hollingshead, Aleksandra; Kroeger, Stephen D.; Altus, Jillian; Trytten, Joyce Brubaker

    2016-01-01

    Struggling with frequent off-task behavior, a teacher in a midwestern inner-city high school requested assistance in her social studies classroom. A study was designed to investigate if a combination of positive behavior supports-based interventions such as behavior-specific praise and reduced teacher reprimands might improve on-task behavior. A…

  3. Mechanical alignment of particles for use in fabricating superconducting and permanent magnetic materials

    International Nuclear Information System (INIS)

    Nellis, W.J.; Maple, M.B.

    1992-01-01

    This patent describes a method of fabricating oriented compacts of superconducting and/or permanent magnetic material. It comprises: providing a base layer of support material, mechanically orienting aligned superconducting or permanently magnetic particles into the desired orientation on the base layer, without mixing the particles with a liquid, optionally covering the particles with a support material, fabricating the base layer and oriented particles assemblage into a desired construct and recovering the resulting fabricated material

  4. Behavioral similarity measurement based on image processing for robots that use imitative learning

    Science.gov (United States)

    Sterpin B., Dante G.; Martinez S., Fernando; Jacinto G., Edwar

    2017-02-01

    In the field of the artificial societies, particularly those are based on memetics, imitative behavior is essential for the development of cultural evolution. Applying this concept for robotics, through imitative learning, a robot can acquire behavioral patterns from another robot. Assuming that the learning process must have an instructor and, at least, an apprentice, the fact to obtain a quantitative measurement for their behavioral similarity, would be potentially useful, especially in artificial social systems focused on cultural evolution. In this paper the motor behavior of both kinds of robots, for two simple tasks, is represented by 2D binary images, which are processed in order to measure their behavioral similarity. The results shown here were obtained comparing some similarity measurement methods for binary images.

  5. Extended child and caregiver benefits of behavior-based child contingency learning games.

    Science.gov (United States)

    Dunst, Carl J; Raab, Melinda; Trivette, Carol M; Wilson, Linda L; Hamby, Deborah W; Parkey, Cindy

    2010-08-01

    Findings from 2 studies of the relationship between response-contingent child behavior and child, caregiver-child, and caregiver behavior not directly associated with child contingency learning are described. The participants were 19 children with significant developmental delays and their mothers in 1 study and 22 children with significant developmental delays and their teachers in the second study. Caregivers engaged the children in learning games characterized by behavior-based contingencies for 15 weeks. Research staff observed the children and their caregivers in everyday routines and activities and rated child and caregiver behavior while the children and caregivers were not playing the games. Results from both studies showed that the degree of response-contingent responding during the games was related to child and caregiver behavior, not the focus of the contingency learning opportunities afforded the children. Implications for practice are described.

  6. Developing and implementing a positive behavioral reinforcement intervention in prison-based drug treatment: Project BRITE.

    Science.gov (United States)

    Burdon, William M; St De Lore, Jef; Prendergast, Michael L

    2011-09-01

    Within prison settings, the reliance on punishment for controlling inappropriate or noncompliant behavior is self-evident. What is not so evident is the similarity between this reliance on punishment and the use of positive reinforcements to increase desired behaviors. However, seldom do inmates receive positive reinforcement for engaging in prosocial behaviors or, for inmates receiving drug treatment, behaviors that are consistent with or support their recovery. This study provides an overview of the development and implementation of a positive behavioral reinforcement intervention in male and female prison-based drug treatment programs. The active involvement of institutional staff, treatment staff, and inmates enrolled in the treatment programs in the development of the intervention along with the successful branding of the intervention were effective at promoting support and participation. However, these factors may also have ultimately impacted the ability of the randomized design to reliably demonstrate the effectiveness of the intervention.

  7. School-based obesity policy, social capital, and gender differences in weight control behaviors.

    Science.gov (United States)

    Zhu, Ling; Thomas, Breanca

    2013-06-01

    We examined the associations among school-based obesity policies, social capital, and adolescents' self-reported weight control behaviors, focusing on how the collective roles of community and adopted policies affect gender groups differently. We estimated state-level ecologic models using 1-way random effects seemingly unrelated regressions derived from panel data for 43 states from 1991 to 2009, which we obtained from the Centers for Disease Control and Prevention's Youth Risk Behavior Surveillance System. We used multiplicative interaction terms to assess how social capital moderates the effects of school-based obesity policies. School-based obesity policies in active communities were mixed in improving weight control behaviors. They increased both healthy and unhealthy weight control behaviors among boys but did not increase healthy weight control behaviors among girls. Social capital is an important contextual factor that conditions policy effectiveness in large contexts. Heterogeneous behavioral responses are associated with both school-based obesity policies and social capital. Building social capital and developing policy programs to balance outcomes for both gender groups may be challenging in managing childhood obesity.

  8. EDITORIAL: Permanent revolution - or evolution?

    Science.gov (United States)

    Dobson, Ken

    1998-03-01

    Honorary Editor It was that temporary Bolshevik Leon Trotsky who developed the principle of `permanent revolution', a principle that perhaps characterizes the recent history of education in (south) Britain more than does, say, principles traditionally associated with the Conservative or Labour parties. As this editorial is being written, changes are being made to primary school education, and the long-awaited details of the post-Dearing reorganizing of post-16 education are yet to hit the overful bookshelves and filing cabinets of school heads and examination board officials. But something unique has happened recently which might have surprised even Trotsky. The Secretary of State for Education has set up targets for primary school pupils' attainment and threatened (or promised) to resign if they are not met within the lifetime of our newly elected parliament. Of course, if Mr Blunkett is still in a position to resign at that stage he will have been the longest serving Secretary of State since time immemorial. But we should not carp: this is truly a revolutionary idea. Not the promise to resign - although this idea is not so fashionable now as it once was. The revolutionary idea is that a major change to an educational process is actually being made that carries with it a predicted and testable outcome. By contrast, when school physics was refreshed a generation ago by the introduction of Nuffield courses at both pre- and post-16 stages, no `targets' were set. I and many other physics teachers certainly preferred teaching these to teaching their predecessor syllabuses, and might even dare to assert that the pupils liked them too. But we still don't really know whether or not they learned more - or even better - physics. Very little happened as far as the outside world was concerned: the usual fraction of students gave up physics at the usual ages, and those who were examined didn't really get a better reward for their more up-to-date and more enjoyably learned

  9. Long term strain behavior of PMMA based polymer optical fibers

    DEFF Research Database (Denmark)

    Bundalo, Ivan-Lazar; Nielsen, Kristian; Woyessa, Getinet

    2015-01-01

    We are reporting on the viscoelasticity of PMMA based Fiber Bragg Grating (FBG) strain sensors when exposed to repeated sequences of long term strain and relaxation with various duty-cycles. In terms of the FBG wavelength and how it follows the strain cycle, we have shown that in the small strain...... regime (up to 1%) an elastic-dominated fast relaxing range, which is followed by a mainly viscous relaxation, depends both on the strain level and on the strain duration. For a small ratio of the strain-relax durations, this fast relaxation range stays almost the same. However, with increasing strain...... duration, for the same relaxation time, this range will be shortened, which might influence the sensing capabilities of the fiber sensor....

  10. Statistics-based email communication security behavior recognition

    Science.gov (United States)

    Yi, Junkai; Su, Yueyang; Zhao, Xianghui

    2017-08-01

    With the development of information technology, e-mail has become a popular communication medium. It has great significant to determine the relationship between the two sides of the communication. Firstly, this paper analysed and processed the content and attachment of e-mail using the skill of steganalysis and malware analysis. And it also conducts the following feature extracting and behaviour model establishing which based on Naive Bayesian theory. Then a behaviour analysis method was employed to calculate and evaluate the communication security. Finally, some experiments about the accuracy of the behavioural relationship of communication identifying has been carried out. The result shows that this method has a great effects and correctness as eighty-four percent.

  11. Developments in the processing and properties of NdFeb-type permanent magnets

    International Nuclear Information System (INIS)

    Brown, David; Ma, B.-M.; Chen Zhongmin

    2002-01-01

    The composition, microstructure and processing of NdFeB-type permanent magnets are all critical factors for the successful production of high performance magnet components. Three common fabrication routes can be used to categorize these NdFeB-based bulk magnets: sintering, polymer bonding and hot deformation. Generally, the former type of magnet has a high-energy product (30-50 MGOe), full density and a relatively simple shape. Bonded magnets have intermediate energy products (10-18 MGOe), lower density and can be formed into intricate net-shapes. Hot deformed magnets possess full density, intermediate to high-energy products (15-46 MGOe), isotropic or anisotropic properties and have the potential to be formed into net shapes. This article discusses the critical issues of improved magnetic performance, environmental stability, net-shape formability and magnetization behavior for the main categories of NdFeB magnets

  12. Fabrication and electrochemical behavior of single-walled carbon nanotube/graphite-based electrode

    International Nuclear Information System (INIS)

    Moghaddam, Abdolmajid Bayandori; Ganjali, Mohammad Reza; Dinarvand, Rassoul; Razavi, Taherehsadat; Riahi, Siavash; Rezaei-Zarchi, Saeed; Norouzi, Parviz

    2009-01-01

    An electrochemical method for determining the dihydroxybenzene derivatives on glassy carbon (GC) has been developed. In this method, the performance of a single-walled carbon nanotube (SWCNT)/graphite-based electrode, prepared by mixing SWCNTs and graphite powder, was described. The resulting electrode shows an excellent behavior for redox of 3,4-dihydroxybenzoic acid (DBA). SWCNT/graphite-based electrode presents a significant decrease in the overvoltage for DBA oxidation as well as a dramatic improvement in the reversibility of DBA redox behavior in comparison with graphite-based and glassy carbon (GC) electrodes. In addition, scanning electron microscopy (SEM) and atomic force microscopy (AFM) procedures performed for used SWCNTs

  13. Efficacy of a brief image-based multiple-behavior intervention for college students.

    Science.gov (United States)

    Werch, Chudley E; Moore, Michele J; Bian, Hui; DiClemente, Carlo C; Ames, Steven C; Weiler, Robert M; Thombs, Dennis; Pokorny, Steven B; Huang, I-Chan

    2008-10-01

    Epidemiologic data indicate most adolescents and adults experience multiple, simultaneous risk behaviors. The purpose of this study is to examine the efficacy of a brief image-based multiple-behavior intervention (MBI) for college students. A total of 303 college students were randomly assigned to: (1) a brief MBI or (2) a standard care control, with a 3-month postintervention follow-up. Omnibus treatment by time multivariate analysis of variance interactions were significant for three of six behavior groupings, with improvements for college students receiving the brief MBI on alcohol consumption behaviors, F(6, 261) = 2.73, p = 0.01, marijuana-use behaviors, F(4, 278) = 3.18, p = 0.01, and health-related quality of life, F(5, 277) = 2.80, p = 0.02, but not cigarette use, exercise, and nutrition behaviors. Participants receiving the brief MBI also got more sleep, F(1, 281) = 9.49, p = 0.00, than those in the standard care control. A brief image-based multiple-behavior intervention may be useful in influencing a number of critical health habits and health-related quality-of-life indicators of college students.

  14. Taxonomy-based content analysis of sedentary behavior questionnaires: A systematic review

    Science.gov (United States)

    Rivière, Fabien; Aubert, Salomé; Omorou, Abdou Yacoubou; Ainsworth, Barbara E.

    2018-01-01

    Background Health effects of sedentary behaviors (SB) may vary depending on their characteristics such as type, purpose, duration, and intensity of the behavior. While a growing number of questionnaires assess sedentary behaviors, it is unclear which characteristics of SB are measured. The aim of this review was to examine the content of self-report SB questionnaires. Methods Three databases were searched for sedentary behavior questionnaires published before January 1st, 2016. Based on the inclusion criteria, 82 articles out of 1369 were retrieved for a total of 60 questionnaires. For each questionnaire, the sedentary behavior characteristics identified were reported and analyzed. Results Most of the questionnaires assessed the time (n = 60), posture (n = 54), purpose (n = 46) and the types (n = 45) of SB performed. Fewer questionnaires assessed the environment (n = 20) social context (n = 11), status (n = 2), and associated behaviors (n = 2) related to sedentary behaviors. All the questionnaires except two assessed time spent in SB with 17 assessing frequency and 6 assessing breaks in SB. The most frequent characteristics identified in the questionnaires were the categories of sitting (90%), a day (95%), watching television (65%) and using a computer (55%). Many characteristics of SB were not measured. Conclusions By knowing the breadth of SB included in questionnaires, this review provides support to shape the design of new questionnaires designed to reduce the gaps in measuring sedentary behaviors. PMID:29509791

  15. FUZZY FAULT DETECTION FOR PERMANENT MAGNET SYNCHRONOUS GENERATOR

    Directory of Open Access Journals (Sweden)

    N. Selvaganesan

    2011-07-01

    Full Text Available Faults in engineering systems are difficult to avoid and may result in serious consequences. Effective fault detection and diagnosis can improve system reliability and avoid expensive maintenance. In this paper fuzzy system based fault detection scheme for permanent magnet synchronous generator is proposed. The sequence current components like positive and negative sequence currents are used as fault indicators and given as inputs to fuzzy fault detector. Also, the fuzzy inference system is created and rule base is evaluated, relating the sequence current component to the type of faults. These rules are fired for specific changes in sequence current component and the faults are detected. The feasibility of the proposed scheme for permanent magnet synchronous generator is demonstrated for different types of fault under various operating conditions using MATLAB/Simulink.

  16. Electrochemical behavior of amorphous metal-silicon-carbon nanocomposites based on titanium or tungsten nanophase

    International Nuclear Information System (INIS)

    Pleskov, Yu.V.; Krotova, M.D.; Shupegin, M.L.; Bozhko, A.D.

    2009-01-01

    Electrode behavior of nanocomposite films containing titanium- or tungsten-based conducting nanophase embedded in dielectric silicon-carbon matrix, deposited onto glassceramics substrate, is studied by cyclic voltammetry and electrochemical impedance spectroscopy. As the films' resistivity decreases, their electrochemical behavior gradually changes from that of 'poor conductor' to the nearly metal-like behavior. In particular, the differential capacitance increases, the charge transfer in a model redox system [Fe(CN) 6 ] 3-/4- accelerates, which may be explained by the increasing number of metal-containing clusters at the film/electrolyte solution interface

  17. A Model to Assess the Behavioral Impacts of Consultative Knowledge Based Systems.

    Science.gov (United States)

    Mak, Brenda; Lyytinen, Kalle

    1997-01-01

    This research model studies the behavioral impacts of consultative knowledge based systems (KBS). A study of graduate students explored to what extent their decisions were affected by user participation in updating the knowledge base; ambiguity of decision setting; routinization of usage; and source credibility of the expertise embedded in the…

  18. Magnetic Performance of a Nanocomposite Permanent Material

    International Nuclear Information System (INIS)

    Liu Min; Han Guang-Bing; Gao Ru-Wei

    2011-01-01

    We build a sandwiched structure model in which the intergranular phase (IP) is homogeneously distributed between soft and hard magnetic grains, and gives a continuously anisotropic expression of the coupling part under the assumption that the IP weakens the intergrain exchange-coupling interaction. Based on the idea that the hardening mechanism is of the pinning type, we calculate the effect of the IP's thickness d and its anisotropy constant K 1 (0) on the intrinsic coercivity of a nanocomposite permanent material. The calculated results indicate that the domain wall goes twice through irreversible domain wall displacement during the process of moving from soft to hard magnetic grains, and the intrinsic coercivity increases with increasing d, but decreases with increasing K 1 (0). When d and K 1 (0) take 2 nm and 0.7K h , respectively, with K h being the anisotropy constant in the inner part of the hard magnetic grain, the calculated intrinsic coercivity is in good agreement with the experimental data. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  19. Rare earth elements and permanent magnets (invited)

    Science.gov (United States)

    Dent, Peter C.

    2012-04-01

    Rare earth (RE) magnets have become virtually indispensible in a wide variety of industries such as aerospace, automotive, electronics, medical, and military. RE elements are essential ingredients in these high performance magnets based on intermetallic compounds RECo5, RE2TM17 (TM: transition metal), and RE2TM14B. Rare earth magnets are known for their superior magnetic properties—high induction, and coercive force. These properties arise due to the extremely high magnetocrystalline anisotropy made possible by unique 3d-4f interactions between transition metals and rare earths. For more than 40 years, these magnets remain the number one choice in applications that require high magnetic fields in extreme operating conditions—high demagnetization forces and high temperature. EEC produces and specializes in RECo5 and RE2TM17 type sintered magnets. Samarium and gadolinium are key RE ingredients in the powder metallurgical magnet production processes which include melting, crushing, jet milling, pressing, sintering, and heat treating. The magnetic properties and applications of these magnets will be discussed. We will also briefly discuss the past, current, and future of the permanent magnet business. Currently, over 95% of all pure rare earth oxides are sourced from China, which currently controls the market. We will provide insights regarding current and potential new magnet technologies and designer choices, which may mitigate rare earth supply chain issues now and into the future.

  20. The optical behavior of amorphous microribbons for hydroxy-naphthol based Schiff bases

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Ping; Liu, Chunlin; Yang, Wei; Liu, Xuan; Du, Jinya [College of Biological and Pharmaceutical Science, China Three Gorges University, Yichang 443002 (China); Liu, Yi [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan 430072 (China); Yang, Changying, E-mail: changying.yang@ctgu.edu.cn [College of Biological and Pharmaceutical Science, China Three Gorges University, Yichang 443002 (China)

    2017-05-15

    The optical behaviors of three hydroxy-naphthol based Schiff bases, L1, L2 and L3, in aggregated states in 1,4-dioxane (Diox) – H{sub 2}O mixture, were investigated. The intermolecular hydrogen bond between luminogen and water resulted in the twisting of benzothiazole group, which is favorable for the assembly of organic molecules into J-aggregates. And also a bathochromic shift in absorption and enhancement of the fluorescence emission (aggregation-induced enhanced emission, AIEE) can be observed. L1 and L2 in Diox-H{sub 2}O mixture with water volume fractions (f{sub w}) 95% assembled into microribbons with 40–50 nm thickness, twisted together to make amorphous supramolecular organogels. Whereas L3 assembled into needle-like nanorods with the thickness up to ~200 nm, consistence with its lower emission intensity compared to L1, L2 aggregates. Moreover, a drastic blue-shift and an enhancement of emission efficiency of L1-L3 were also observed in solid states with the morphology change from the crystalline to the amorphous state by grinding. It was found that L1 aggregates showed fluorescence switch-off sensing towards Cu{sup 2+}, with higher selectivity and sensitivity compared to L1 in Diox solution. - Graphical abstract: Three Schiff bases derivatives, L1, L2 and L3, consisting of hydroxy-naphthol and thiazole group, exhibited AIEE effect in Diox-H{sub 2}O mixture with f{sub w} 95% (for L1 and L2) or 99% (for L3). The formation of amorphous nanoparticles is advantageous for emission enhancement. The drastic blue-shift and an enhancement of emission efficiency were also observed in L1-L3 with the morphology change from the crystalline to the amorphous state in solid by grinding. It was found that L1 AIEE system could be constructed as a chemoprobe towards Cu{sup 2+} fluorescence recognition, with higher selectivity and sensitivity compared to L1 in Diox solution.

  1. Mobility Behavior of the Elderly: an attitude-based segmentation approach for a heterogeneous target group

    DEFF Research Database (Denmark)

    Haustein, Sonja

    2012-01-01

    The western population is ageing. Based on the assumption that the elderly are a quite heterogeneous population group with an increasing impact on the transport system, mobility types of the elderly were identified. By means of 1,500 standardized telephone interviews, mobility behavior and possib...... of the diverse lifestyles, attitudes, travel behavior and needs of the elderly. Furthermore, it identifies starting points for the reduction of car use....

  2. Thermal behavior for a nanoscale two ferromagnetic phase system based on random anisotropy model

    International Nuclear Information System (INIS)

    Muraca, D.; Sanchez, F.H.; Pampillo, L.G.; Saccone, F.D.

    2010-01-01

    Advances in theory that explain the magnetic behavior as function of temperature for two phase nanocrystalline soft magnetic materials are presented. The theory developed is based on the well known random anisotropy model, which includes the crystalline exchange stiffness and anisotropy energies in both amorphous and crystalline phases. The phenomenological behavior of the coercivity was obtained in the temperature range between the amorphous phase Curie temperature and the crystalline phase one.

  3. An Explanation to Individual Knowledge and Behavior Based on Empirical Substrates

    OpenAIRE

    Zhao, Liang; Zhu, Xian Chen

    2008-01-01

    Using recent findings from modern empirical disciplines and mainly building on F.A.Hayek’s thoughts, the paper gives a definition of knowledge in accord with the Austrian School’s tradition, and basing on the definition, it sums up three behavior assumptions and a framework on explaining individual behavior and expounds ideas on hierarchical knowledge and its change in real situations. By this way, the paper believes that the Austrian School can be greatly advanced with the help of modern emp...

  4. Modeling and Recognizing Driver Behavior Based on Driving Data: A Survey

    OpenAIRE

    Wang, Wenshuo; Xi, Junqiang; Chen, Huiyan

    2014-01-01

    In recent years, modeling and recognizing driver behavior have become crucial to understanding intelligence transport systems, human-vehicle systems, and intelligent vehicle systems. A wide range of both mathematical identification methods and modeling methods of driver behavior are presented from the control point of view in this paper based on the driving data, such as the brake/throttle pedal position and the steering wheel angle, among others. Subsequently, the driver’s characteristics de...

  5. Complex Behavior in an Integrate-and-Fire Neuron Model Based on Small World Networks

    International Nuclear Information System (INIS)

    Lin Min; Chen Tianlun

    2005-01-01

    Based on our previously pulse-coupled integrate-and-fire neuron model in small world networks, we investigate the complex behavior of electroencephalographic (EEG)-like activities produced by such a model. We find EEG-like activities have obvious chaotic characteristics. We also analyze the complex behaviors of EEG-like signals, such as spectral analysis, reconstruction of the phase space, the correlation dimension, and so on.

  6. Contextualization and standardization of the supportive leadership behavior questionnaire based on socio- cognitive theory in Iran

    OpenAIRE

    Shirazi, Mandana; Emami, Amir Hosein; Mirmoosavi, ,Seyed Jamal; Alavinia, Seyed Mohammad; Zamanian, Hadi; Fathollahbeigi, Faezeh; Masiello, Italo

    2014-01-01

    Background: Effective leadership is of prime importance in any organization and it goes through changes based on accepted health promotion and behavior change theory. Although there are many leadership styles, transformational leadership, which emphasizes supportive leadership behaviors, seems to be an appropriate style in many settings particularly in the health care and educational sectors which are pressured by high turnover and safety demands. Iran has been moving rapidly forward and its ...

  7. Improving Chronic Disease in the Caribbean through Evidence-based Behavioral and Social In

    Science.gov (United States)

    The Office for Behavioral and Social Sciences Research and the NCI’s Center for Global Health held a workshop entitled “Improving Chronic Disease in the Caribbean through Evidence-based Behavioral and Social Interventions”, which took place in Bridgetown, Barbados from July 21 to 24, 2015. The objectives of the workshop were to encourage the generation of research to more rapidly accelerate chronic disease prevention and management.

  8. Mindfulness-Based Interventions for Obesity-Related Eating Behaviors: A Literature Review

    OpenAIRE

    O’Reilly, Gillian A.; Cook, Lauren; Spruijt-Metz, Donna; Black, David S.

    2014-01-01

    Mindfulness-based interventions (MBIs) targeting eating behaviors have gained popularity in recent years. A literature review was conducted to determine the effectiveness of MBIs for treating obesity-related eating behaviors, such as binge eating, emotional eating, and external eating. A search protocol was conducted using the online databases Google Scholar, PubMed, PsycINFO, and Ovid Healthstar. Articles were required to meet the following criteria to be included in this review: (1) describ...

  9. A STUDY ON THE SHAREHOLDERS’ BEHAVIOR OF LISTED COMPANIES BASED ON SYMBIOSIS THEORY: A RESEARCH FRAMEWORK

    OpenAIRE

    YANG Songling; LIU Tingli; CHEN Fang

    2014-01-01

    Research on shareholder’s behavior is a hot topic in recent years. Most researches are based on the theory of agency, which proposal that equity decentralization is the major way to solve the conflict problem between large shareholders and minority stockholders. Actually, major shareholder will never be eliminated. This paper introduces the symbiosis theory-ecology theory-to explain the motives and consequences of the behavior of different type shareholders in China’s from a new perspective. ...

  10. Effect of Attachment-Based Therapy on Behavioral Disorders in Girls with Attachment Problems

    Directory of Open Access Journals (Sweden)

    Marzieh Jahanbakhsh

    2014-09-01

    Full Text Available Background: Multidimensional and complex nature of children`s behavioral disorders requires assessment and usage of modern treatments. The present study investigated the effects of attachment-based therapy on behavioral disorders (depression, over anxiety and oppositional defiant in girl students of primary school who had attachment problems. Materials and Methods: This study is an empirical plan with pretest-posttest and control group. The target samples were 34 individuals of 388 second and fourth grade students of primary school that had highest scores on attachment problems and behavioral disorders (depression, over anxiety and oppositional defiant. Evaluation implemented using Randolph attachment disorder questionnaire (RADQ and Ontario mental health test. Mothers were presented in 10 group sessions of attachment-based intervention and its effects investigated in their girl`s behavioral disorders (depression, over anxiety and oppositional defiant. Results: Reduction rate of behavioral disorders general scores (depression, over anxiety and oppositional defiant of experimental group compared with control group showed significant decreases in posttest and three months follow up. Conclusion: The attachment based therapy offered for mothers of the girls with attachment problems was effective to reduction of behavioral disorders (depression, over anxiety and oppositional defiant symptoms in their children and the mother`s continues attention to interventional methods showed more improvement in follow up evaluation.

  11. The Use of a Functional Behavioral Assessment-Based Self Management Intervention for Students with Emotional/Behavioral Disorders

    Science.gov (United States)

    Rasheed, Saleem A.; Fore, Cecil, III; Jones, Arthur; Smith, Latisha

    2012-01-01

    The research literature on the use of Functional Behavioral Assessments (FBA) to develop Behavior Intervention Plans (BIP) for students with emotional/behavioral disorders, who present problem classroom behaviors for use in the schools, is well documented. There are school-wide, district-wide, and state-wide plans that are currently being…

  12. Causes of permanent childhood hearing impairment.

    Science.gov (United States)

    Korver, Anna M H; Admiraal, Ronald J C; Kant, Sarina G; Dekker, Friedo W; Wever, Capi C; Kunst, Henricus P M; Frijns, Johan H M; Oudesluys-Murphy, Anne Marie

    2011-02-01

    The causes of Permanent Childhood Hearing Impairment (PCHI) are often quoted as being hereditary in 50%, acquired in 25%, and unknown in 25% of cases. Interest in the causes of PCHI has grown recently due to increasing diagnostic possibilities. We investigated the evidence for the reported distribution of these causes. Population-based study and a systematic review. Inclusion criteria for population-based study: children born between 2003 and 2005, resident in The Netherlands at birth, known at an Audiology Center with PCHI at the age of 3-5 years. The causes of PCHI were determined prospectively by detection of congenital cytomegalovirus on dried blood spots and/or genetic diagnostic investigations in addition to reviewing data from medical records. A systematic review was carried out using three terms (hearing loss, infant, and etiology) and limited to articles published between January 1997 and July 2009. Main outcome measures were: the (weighted) proportions of the various causes of PCHI following diagnostic investigations. In the study-population (n = 185) a hereditary cause was found in 38.9%, acquired cause in 29.7%, miscellaneous cause in 7.1%, and the cause remained unknown in 24.3%. The systematic review of the literature (n = 9 articles) resulted in a weighted mean of 30.4% hereditary, 19.2% acquired, and 48.3% unknown causes of PCHI. The systematic review and the results of the population-based study provided little support for the generally accepted distribution of causes of PCHI. Copyright © 2010 The American Laryngological, Rhinological, and Otological Society, Inc.

  13. An entropy-based analysis of lane changing behavior: An interactive approach.

    Science.gov (United States)

    Kosun, Caglar; Ozdemir, Serhan

    2017-05-19

    As a novelty, this article proposes the nonadditive entropy framework for the description of driver behaviors during lane changing. The authors also state that this entropy framework governs the lane changing behavior in traffic flow in accordance with the long-range vehicular interactions and traffic safety. The nonadditive entropy framework is the new generalized theory of thermostatistical mechanics. Vehicular interactions during lane changing are considered within this framework. The interactive approach for the lane changing behavior of the drivers is presented in the traffic flow scenarios presented in the article. According to the traffic flow scenarios, 4 categories of traffic flow and driver behaviors are obtained. Through the scenarios, comparative analyses of nonadditive and additive entropy domains are also provided. Two quadrants of the categories belong to the nonadditive entropy; the rest are involved in the additive entropy domain. Driving behaviors are extracted and the scenarios depict that nonadditivity matches safe driving well, whereas additivity corresponds to unsafe driving. Furthermore, the cooperative traffic system is considered in nonadditivity where the long-range interactions are present. However, the uncooperative traffic system falls into the additivity domain. The analyses also state that there would be possible traffic flow transitions among the quadrants. This article shows that lane changing behavior could be generalized as nonadditive, with additivity as a special case, based on the given traffic conditions. The nearest and close neighbor models are well within the conventional additive entropy framework. In this article, both the long-range vehicular interactions and safe driving behavior in traffic are handled in the nonadditive entropy domain. It is also inferred that the Tsallis entropy region would correspond to mandatory lane changing behavior, whereas additive and either the extensive or nonextensive entropy region would

  14. Teleconsultation in school settings: linking classroom teachers and behavior analysts through web-based technology.

    Science.gov (United States)

    Frieder, Jessica E; Peterson, Stephanie M; Woodward, Judy; Crane, Jaelee; Garner, Marlane

    2009-01-01

    This paper describes a technically driven, collaborative approach to assessing the function of problem behavior using web-based technology. A case example is provided to illustrate the process used in this pilot project. A school team conducted a functional analysis with a child who demonstrated challenging behaviors in a preschool setting. Behavior analysts at a university setting provided the school team with initial workshop trainings, on-site visits, e-mail and phone communication, as well as live web-based feedback on functional analysis sessions. The school personnel implemented the functional analysis with high fidelity and scored the data reliably. Outcomes of the project suggest that there is great potential for collaboration via the use of web-based technologies for ongoing assessment and development of effective interventions. However, an empirical evaluation of this model should be conducted before wide-scale adoption is recommended.

  15. Discrepancy-based and anticipated emotions in behavioral self-regulation.

    Science.gov (United States)

    Brown, Christina M; McConnell, Allen R

    2011-10-01

    Discrepancies between one's current and desired states evoke negative emotions, which presumably guide self-regulation. In the current work we evaluated the function of discrepancy-based emotions in behavioral self-regulation. Contrary to classic theories of self-regulation, discrepancy-based emotions did not predict the degree to which people engaged in self-regulatory behavior. Instead, expectations about how future self-discrepancies would make one feel (i.e., anticipated emotions) predicted self-regulation. However, anticipated emotions were influenced by previous discrepancy-based emotional experiences, suggesting that the latter do not directly motivate self-regulation but rather guide expectations. These findings are consistent with the perspective that emotions do not necessarily direct immediate behavior, but rather have an indirect effect by guiding expectations, which in turn predict goal-directed action.

  16. Using findings in multimedia learning to inform technology-based behavioral health interventions.

    Science.gov (United States)

    Aronson, Ian David; Marsch, Lisa A; Acosta, Michelle C

    2013-09-01

    Clinicians and researchers are increasingly using technology-based behavioral health interventions to improve intervention effectiveness and to reach underserved populations. However, these interventions are rarely informed by evidence-based findings of how technology can be optimized to promote acquisition of key skills and information. At the same time, experts in multimedia learning generally do not apply their findings to health education or conduct research in clinical contexts. This paper presents an overview of some key aspects of multimedia learning research that may allow those developing health interventions to apply informational technology with the same rigor as behavioral science content. We synthesized empirical multimedia learning literature from 1992 to 2011. We identified key findings and suggested a framework for integrating technology with educational and behavioral science theory. A scientific, evidence-driven approach to developing technology-based interventions can yield greater effectiveness, improved fidelity, increased outcomes, and better client service.

  17. Data Sources for the Model-based Small Area Estimates of Cancer Risk Factors and Screening Behaviors - Small Area Estimates

    Science.gov (United States)

    The model-based estimates of important cancer risk factors and screening behaviors are obtained by combining the responses to the Behavioral Risk Factor Surveillance System (BRFSS) and the National Health Interview Survey (NHIS).

  18. Factors associated with communication-based sedentary behaviors among youth: are talking on the phone, texting, and instant messaging new sedentary behaviors to be concerned about?

    Science.gov (United States)

    Leatherdale, Scott T

    2010-09-01

    Sedentary behavior research typically only examines screen time activities and not communication time activities, such as talking on the phone, texting, or instant messaging. Data from 2,449 grade 5 to 8 students were used to examine factors associated with the time youth spent in communication-based sedentary behaviors. Screen time, physical activity, grade, and gender were associated with moderate and high communication time. Future research on sedentary behavior should include measures of communication time.

  19. JACOS: AI-based simulation system for man-machine system behavior in NPP

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Kazuo; Yokobayashi, Masao; Tanabe, Fumiya [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kawase, Katsumi [CSK Corp., Tokyo (Japan); Komiya, Akitoshi [Computer Associated Laboratory, Inc., Hitachinaka, Ibaraki (Japan)

    2001-08-01

    A prototype of a computer simulation system named JACOS (JAERI COgnitive Simulation system) has been developed at JAERI (Japan Atomic Energy Research Institute) to simulate the man-machine system behavior in which both the cognitive behavior of a human operator and the plant behavior affect each other. The objectives of this system development is to provide man-machine system analysts with detailed information on the cognitive process of an operator and the plant behavior affected by operator's actions in accidental situations of a nuclear power plant. The simulation system consists of an operator model and a plant model which are coupled dynamically. The operator model simulates an operator's cognitive behavior in accidental situations based on the decision ladder model of Rasmussen, and is implemented using the AI-techniques of the distributed cooperative inference method with the so-called blackboard architecture. Rule-based behavior is simulated using knowledge representation with If-Then type of rules. Knowledge-based behavior is simulated using knowledge representation with MFM (Multilevel Flow Modeling) and qualitative reasoning method. Cognitive characteristics of attentional narrowing, limitation of short-term memory, and knowledge recalling from long-term memory are also taken into account. The plant model of a 3-loop PWR is also developed using a best estimate thermal-hydraulic analysis code RELAP5/MOD2. This report is prepared as User's Manual for JACOS. The first chapter of this report describes both operator and plant models in detail. The second chapter includes instructive descriptions for program installation, building of a knowledge base for operator model, execution of simulation and analysis of simulation results. The examples of simulation with JACOS are shown in the third chapter. (author)

  20. JACOS: AI-based simulation system for man-machine system behavior in NPP

    International Nuclear Information System (INIS)

    Yoshida, Kazuo; Yokobayashi, Masao; Tanabe, Fumiya; Komiya, Akitoshi

    2001-08-01

    A prototype of a computer simulation system named JACOS (JAERI COgnitive Simulation system) has been developed at JAERI (Japan Atomic Energy Research Institute) to simulate the man-machine system behavior in which both the cognitive behavior of a human operator and the plant behavior affect each other. The objectives of this system development is to provide man-machine system analysts with detailed information on the cognitive process of an operator and the plant behavior affected by operator's actions in accidental situations of a nuclear power plant. The simulation system consists of an operator model and a plant model which are coupled dynamically. The operator model simulates an operator's cognitive behavior in accidental situations based on the decision ladder model of Rasmussen, and is implemented using the AI-techniques of the distributed cooperative inference method with the so-called blackboard architecture. Rule-based behavior is simulated using knowledge representation with If-Then type of rules. Knowledge-based behavior is simulated using knowledge representation with MFM (Multilevel Flow Modeling) and qualitative reasoning method. Cognitive characteristics of attentional narrowing, limitation of short-term memory, and knowledge recalling from long-term memory are also taken into account. The plant model of a 3-loop PWR is also developed using a best estimate thermal-hydraulic analysis code RELAP5/MOD2. This report is prepared as User's Manual for JACOS. The first chapter of this report describes both operator and plant models in detail. The second chapter includes instructive descriptions for program installation, building of a knowledge base for operator model, execution of simulation and analysis of simulation results. The examples of simulation with JACOS are shown in the third chapter. (author)