Revised analysis of the Transition Joint Life Test

Energy Technology Data Exchange (ETDEWEB)

Sartory, W K

1984-07-01

The Transition Joint Life Test was performed by General Electric and the Energy Technology Engineering Center and was analyzed earlier by General Electric. Because of later developments in analysis techniques and in our understanding of the stress behavior near a dissimilar metal weldment, agreement was reached between General Electric and Oak Ridge National Laboratory`s High-Temperature Structural Design program that a more up-to-date analysis was needed. This report presents results of a new analysis incorporating modified mechanical properties, revised constitutive equations, and a more refined finite element grid. The structural life prediction of the present report is quite conservative (approximately 3 cycles of predicted life compared to 12 to 25 cycles of measured life), whereas the earlier General Electric analysis was underconservative by a similar factor.

Revision report about the in-situ tests of 1000 MW unit 5 Kozloduy (Bulgaria)

International Nuclear Information System (INIS)

Muzzi, F.

1995-01-01

This report refers to the technical revision performed on the technical report about the in-situ tests performed on 1000 Unit 5 nuclear power station of Kozloduy (Bulgaria), within the frame of the IAEA benchmark study for the seismic analysis and testing of an existing Nuclear Power Plant. After a foreword to define the aims of the job and the identification of the scope of the work, a brief description of the plant is made. A brief description of the theory about the modal parameter determination and the soil-structure interaction analysis by experimental tests is made. The following chapters collect some comments about the tests carried out in Kozloduy, with special reference to the general correctness of testing procedure and to data special requirements for the seismic safety margin assessment procedures to be applied on the existing power station

Deciding to adopt revised and new psychological and neuropsychological tests: an inter-organizational position paper.

Science.gov (United States)

Bush, Shane S; Sweet, Jerry J; Bianchini, Kevin J; Johnson-Greene, Doug; Dean, Pamela M; Schoenberg, Mike R

2018-04-01

Neuropsychological tests undergo periodic revision intended to improve psychometric properties, normative data, relevance of stimuli, and ease of administration. In addition, new tests are developed to evaluate psychological and neuropsychological constructs, often purporting to improve evaluation effectiveness. However, there is limited professional guidance to neuropsychologists concerning the decision to adopt a revised version of a test and/or replace an older test with a new test purporting to measure the same or overlapping constructs. This paper describes ethical and professional issues related to the selection and use of older versus newer psychological and neuropsychological tests, with the goal of promoting appropriate test selection and evidence-based decision making. Ethical and professional issues were reviewed and considered. The availability of a newer version of a test does not necessarily render obsolete prior versions of the test for purposes that are empirically supported, nor should continued empirically supported use of a prior version of a test be considered unethical practice. Until a revised or new test has published evidence of improved ability to help clinicians to make diagnostic determinations, facilitate treatment, and/or assess change over time, the choice to delay adoption of revised or new tests may be viewed as reasonable and appropriate. Recommendations are offered to facilitate decisions about the adoption of revised and new tests. Ultimately, it is the responsibility of individual neuropsychologists to determine which tests best meet their patients' needs, and to be able to support their decisions with empirical evidence and sound clinical judgment.

Testing Math or Testing Language? The Construct Validity of the KeyMath-Revised for Children With Intellectual Disability and Language Difficulties.

Science.gov (United States)

Rhodes, Katherine T; Branum-Martin, Lee; Morris, Robin D; Romski, MaryAnn; Sevcik, Rose A

2015-11-01

Although it is often assumed that mathematics ability alone predicts mathematics test performance, linguistic demands may also predict achievement. This study examined the role of language in mathematics assessment performance for children with intellectual disability (ID) at less severe levels, on the KeyMath-Revised Inventory (KM-R) with a sample of 264 children, in grades 2-5. Using confirmatory factor analysis, the hypothesis that the KM-R would demonstrate discriminant validity with measures of language abilities in a two-factor model was compared to two plausible alternative models. Results indicated that KM-R did not have discriminant validity with measures of children's language abilities and was a multidimensional test of both mathematics and language abilities for this population of test users. Implications are considered for test development, interpretation, and intervention.

Concurrent validity of the Snijders-Oomen Nonverbal Intelligence Test 2 1/2-7-Revised with the Wechsler Preschool and Primary Scale of Intelligence - Revised

NARCIS (Netherlands)

Moore, C; O'Keefe, SL; Lawhon, D; Tellegen, P

This study examined the concurrent validity of the Snijders-Oomen Nonverbal Intelligence Test-Revised compared to the Wechsler Preschool and Primary Scale of Intelligence-Revised Subjects were 25 4-yr.-olds of lower, lower-middle, and middle socioeconomic status from both urban and rural areas of

Test plan for evaluating the performance of the in-tank fluidic sampling system

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

The PHMC will provide Low Activity Wastes (LAW) tank wastes for final treatment by a privatization contractor from double-shell feed tanks, 241-AP-102 and 241-AP-104, Concerns about the inability of the baseline ''grab'' sampling to provide large volume samples within time constraints has led to the development of a conceptual sampling system that would be deployed in a feed tank riser, This sampling system will provide large volume, representative samples without the environmental, radiation exposure, and sample volume impacts of the current base-line ''grab'' sampling method. This test plan identifies ''proof-of-principle'' cold tests for the conceptual sampling system using simulant materials. The need for additional testing was identified as a result of completing tests described in the revision test plan document, Revision 1 outlines tests that will evaluate the performance and ability to provide samples that are representative of a tanks' content within a 95 percent confidence interval, to recovery from plugging, to sample supernatant wastes with over 25 wt% solids content, and to evaluate the impact of sampling at different heights within the feed tank. The test plan also identifies operating parameters that will optimize the performance of the sampling system

Performance Test of CCTV in a Test Field

Energy Technology Data Exchange (ETDEWEB)

Seo, Hyung Min [Korea Institute of Nuclear Nonproliferation and Control, Daejeon (Korea, Republic of)

2011-10-15

On April 12-13, 2010, US President Obama hosted a Nuclear Security Summit in Washington, DC, to enhance international cooperation to prevent nuclear terrorism, an issue which he has identified as the most immediate and extreme threat to global security. The Summit focused on the security of nuclear materials, nonproliferation, disarmament, and peaceful nuclear energy. At the summit, the Republic of Korea was chosen as the host of the next Summit in 2012. This series of events reflects the growing global interest on 'Nuclear Security' and as the host country of the next Nuclear Summit it is the time for Korea to strengthen the physical protection regime for nuclear facilities as a first step of securing its nuclear security capability. KINAC has been operating Test field as a mean of preparing solid backup data for reviewing and revising DBT (Design Basis Threat) and to test components of the conventional physical protection system. CCTV is a key component which is used worldwide for the assessment measure of alarms. In terms of performance test of CCTV, there are several elements such as image quality, coverage and mechanical features (speed of zoom-in-out, capture, angle shift etc.). Speaking of image quality acquired by the CCTV, the quality is subject to resolution, monitor specification, camera housing, camera mounting and lightening. Thus it is clear that performance tests on image quality should consider those factors and vary the factors respectively in order to verify the influence and the interaction among those. Nevertheless due to the restrictions of the current Test field, this paper focuses on the image quality through resolution test under the various lightening conditions

Revision and psychometric testing of the City of Hope Quality of Life-Ostomy Questionnaire.

Science.gov (United States)

Grant, Marcia; Ferrell, Betty; Dean, Grace; Uman, Gwen; Chu, David; Krouse, Robert

2004-10-01

Ostomies may be performed for bowel or urinary diversion, and occur in both cancer and non-cancer patients. Impact on physical, psychological, social and spiritual well-being is not unexpected, but has been minimally described in the literature. The City of Hope Quality of Life (COH-QOL)-Ostomy Questionnaire is an adult patient self-report instrument designed to assess quality of life. This report focuses on the revision and psychometric testing of this questionnaire. The revised COH-QOL-Ostomy Questionnaire involved in-depth patient interviews and expert panel review. The format consisted of a 13-item disease and demographic section, a 34-item forced-choice section, and a 41-item linear analogue scaled section. A mailed survey to California members of the United Ostomy Association resulted in a 62% response rate (n = 1513). Factor analysis was conducted to refine the instrument. Construct validity involved testing a number of hypotheses identifying contrasting groups. Factor analysis confirmed the conceptual framework. Reliability of subscales ranged from 0.77 to 0.90. The questionnaire discriminated between subpopulations with specific concerns. Overall, the analyses provide evidence for the validity and reliability of the COH-QOL-Ostomy Questionnaire as a comprehensive, multidimensional self-report questionnaire for measuring quality of life in patients with intestinal ostomies.

Underground Test Area Quality Assurance Project Plan Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Irene Farnham

2011-05-01

This Quality Assurance Project Plan (QAPP) provides the overall quality assurance (QA) program requirements and general quality practices to be applied to the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Underground Test Area (UGTA) Sub-Project (hereafter the Sub-Project) activities. The requirements in this QAPP are consistent with DOE Order 414.1C, Quality Assurance (DOE, 2005); U.S. Environmental Protection Agency (EPA) Guidance for Quality Assurance Project Plans for Modeling (EPA, 2002); and EPA Guidance on the Development, Evaluation, and Application of Environmental Models (EPA, 2009). The QAPP Revision 0 supersedes DOE--341, Underground Test Area Quality Assurance Project Plan, Nevada Test Site, Nevada, Revision 4.

78 FR 71676 - NUREG-1482, Revision 2, “Guidelines for Inservice Testing at Nuclear Power Plants, Final Report”

Science.gov (United States)

2013-11-29

... Testing at Nuclear Power Plants, Final Report'' AGENCY: Nuclear Regulatory Commission. ACTION: Notice of... entitled: NUREG-1482, Revision 2, ``Guidelines for Inservice Testing at Nuclear Power Plants,'' and... Restraints (Snubbers) at Nuclear Power Plants.'' In the previous Revisions 0 and 1 of NUREG-1482, the NRC...

Safety Evaluation Report on Tennessee Valley Authority: Revised Corporate Nuclear Performance Plan

International Nuclear Information System (INIS)

1987-07-01

The TVA Corporate Nuclear Performance Plan addresses those corporate concerns identified by the NRC staff. Because much of the TVA corporate plan is programmatic, its effectiveness depends on its implementation, and the NRC staff plans to closely monitor this implementation. The NRC staff will address site-specific concerns in subsequent SERs on each volume of the Nuclear Performance Plan. On the basis of its review, the NRC staff finds TVA's revised Corporate Nuclear Performance Plan (Revision 4) acceptable. The NRC staff concludes that the organization and staffing of TVA's Office of Nuclear Power and the programmatic improvements in place or under way are sufficient, if implemented properly, to resolve the problems at the corporate level that led to issuance of the 10 CFR 50.54(f) letter dated September 17, 1985, and to support continuing TVA nuclear activities, including plant operations. 19 refs., 3 figs

Microbiological diagnosis in revision of infected knee arthroplasties in Denmark

DEFF Research Database (Denmark)

Lindberg-Larsen, Martin; Pitter, Frederik Taylor; Voldstedlund, Marianne

2017-01-01

. METHODS: One hundred and two partial revisions (open debridement and exchange of tibial insert) and 213 two-stage procedures performed due to infection in 275 patients from 1 July 2011 to 30 June 2013 were included and analysed by linkage to data from a nationwide registry on microbiological test results....... RESULTS: 78 (24.8%) revisions were culture negative, 192 (60.9%) showed monomicrobial growth and 43 (14.3%) polymicrobial growth. Staphylococcus aureus was the most frequent isolate in mono-culture in 70 (22.2%) revisions and in polymicrobial culture in 15 revisions with a total frequency of 27.0%. Only...... one case (1.4%) of methicillin-resistance was registered. Coagulase-negative staphylococci (CoNS) were frequent, sole pathogen in 65 revisions and in polymicrobial cultures in 28 revisions with a total frequency of 29.5%. A pre-operative knee aspiration was performed in 50% and preoperative blood...

Personal dosimetry performance testing in the United States

International Nuclear Information System (INIS)

Soares, C.G.

2005-01-01

Full text: The basis for personal dosimetry performance testing in the United States is ANSI/HPS N13.11 (2002). Now in its third edition, this standard has been in place since 1983. Testing under this standard is administered by the National Voluntary Accreditation Program (NVLAP), and accreditation of dosimetry processors under this program is required by US Nuclear Regulatory Commission (NRC) regulations. The US Department of Energy (DOE) also maintains a testing program for its laboratories and contractors, administered by the Department of Energy Laboratory Accreditation Program (DOELAP). A focus in recent years has been the modification of ANSI/HPS N13.11 to allow acceptance by both testing programs in order to bring harmonization to US personal dosimeter processing testing. The testing philosophy of ANSI N13.11 has always combined elements of type testing and routine performance testing and is thus different from the testing philosophy used in the rest of the world. This unique philosophy is explored in detail in this presentation, along with trends in the development of the document to its present state. In addition, a look will be taken at what the future holds for the next revision of the document, scheduled to begin in 2005. (author)

What Is the Role and Importance of the Revised AERA, APA, NCME "Standards for Educational and Psychological Testing"?

Science.gov (United States)

Plake, Barbara S.; Wise, Lauress L.

2014-01-01

With the 2014 publication of the 5th revision of the "Standards for Educational and Psychological Testing," the cochairs of the Joint Committee for the revision process were asked to consider the role and importance of the "Standards" for the educational testing community, and in particular for members of the National Council…

European wind turbine testing procedure developments. Task 1: Measurement method to verify wind turbine performance characteristics

DEFF Research Database (Denmark)

Hunter, R.; Friis Pedersen, Troels; Dunbabin, P.

2001-01-01

There is currently significant standardisation work ongoing in the context of wind farm energy yield warranty assessment and wind turbine power performance testing. A standards maintenance team is revising the current IEC (EN) 61400-12 Ed 1 standard forwind turbine power performance testing....... The standard is being divided into four documents. Two of them are drafted for evaluation and verification of complete wind farms and of individual wind turbines within wind farms. This document, and the project itdescribes, has been designed to help provide a solid technical foundation for this revised...... standard. The work was wide ranging and addressed 'grey' areas of knowledge, regarding existing methodologies or to carry out basic research in support offundamentally new procedures. The work has given rise to recommendations in all areas of the work, including site calibration procedures, nacelle...

Revised data taking schedule with ion beams

CERN Document Server

Gazdzicki, Marek; Aduszkiewicz, A; Andrieu, B; Anticic, T; Antoniou, N; Argyriades, J; Asryan, A G; Baatar, B; Blondel, A; Blumer, J; Boldizsar, L; Bravar, A; Brzychczyk, J; Bubak, A; Bunyatov, S A; Choi, K U; Christakoglou, P; Chung, P; Cleymans, J; Derkach, D A; Diakonos, F; Dominik, W; Dumarchez, J; Engel, R; Ereditato, A; Feofilov, G A; Fodor, Z; Ferrero, A; Gazdzicki, M; Golubeva, M; Grebieszkow, K; Grzeszczuk, A; Guber, F; Hasegawa, T; Haungs, A; Igolkin, S; Ivanov, A S; Ivashkin, A; Kadija, K; Katrynska, N; Kielczewska, D; Kikola, D; Kisiel, J; Kobayashi, T; Kolesnikov, V I; Kolev, D; Kolevatov, R S; Kondratiev, V P; Kowalski, S; Kurepin, A; Lacey, R; Laszlo, A; Lyubushkin, V V; Majka, Z; I Malakhov, A; Marchionni, A; Marcinek, A; Maris, I; Matveev, V; Melkumov, G L; Meregaglia, A; Messina, M; Mijakowski, P; Mitrovski, M; Montaruli, T; Mrówczynski, St; Murphy, S; Nakadaira, T; Naumenko, P A; Nikolic, V; Nishikawa, K; Palczewski, T; Pálla, G; Panagiotou, A D; Peryt, W; Planeta, R; Pluta, J; Popov, B A; Posiadala, M; Przewlocki, P; Rauch, W; Ravonel, M; Renfordt, R; Röhrich, D; Rondio, E; Rossi, B; Roth, M; Rubbia, A; Rybczynski, M; Sadovskii, A; Sakashita, K; Schuster, T; Sekiguchi, T; Seyboth, P; Shibata, M; Sissakian, A N; Skrzypczak, E; Slodkowski, M; Sorin, A S; Staszel, P; Stefanek, G; Stepaniak, J; Strabel, C; Ströbele, H; Susa, T; Szentpétery, I; Szuba, M; Tada, M; Taranenko, A; Tsenov, R; Ulrich, R; Unger, M; Vassiliou, M; Vechernin, V V; Vesztergombi, G; Wlodarczyk, Z; Wojtaszek, A; Zipper, W; CERN. Geneva. SPS and PS Experiments Committee; SPSC

2009-01-01

This document presents the revised data taking schedule of NA61 with ion beams. The revision takes into account limitations due to the new LHC schedule as well as final results concerning the physics performance with secondary ion beams. It is proposed to take data with primary Ar and Xe beams in 2012 and 2014, respectively, and to test and use for physics a secondary B beam from primary Pb beam fragmentation in 2010, 2011 and 2013.

Nevada Test Site waste acceptance criteria [Revision 1

Energy Technology Data Exchange (ETDEWEB)

None

1997-08-01

Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document.

Nevada Test Site waste acceptance criteria [Revision 1

International Nuclear Information System (INIS)

None

1997-01-01

Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

Adaption and Standardization of the Test of Visual-Motor Skills Revised

Directory of Open Access Journals (Sweden)

Mozhgan Farahbod

2004-06-01

Full Text Available Objective: This research has been carried out with the aim of adaptation, standardization and finding the validity and reliability of Visual-Motor Skills-revised Test for children. Materials & Methods: A multi-stage sampling from the children of the city of Tehran resulted in a sample of 1281 subjects, ages 2,11 through 13,11.the test consisted of 23 geometric designs and each of the designs was assessed through a definite criteria and was scored as errors(weakness and accuracies(strength.For adaptation and standardization of this test, at first step the examiner`s manual and the test items were translated into Farsi. The final form of the test was obtained after performing the pre-tryout and tryout stages, and doing the data analysis by classic model of reliability. Internal consistency coefficients of the subtests were obtained by Cronbach`s Alpha time consistency of the subtests and compound scores were obtained by test-retest. Alpha coefficients for the compound scores were obtained by Guilford formula, which is designed for estimating the compound scores. To obtain the content validity, criterion-related validity and construct validity of the subtests and compound scores, appropriate methods were used. Results: The results obtained ensure the applicability of this test for the evaluation of visual-motor skills of children of Tehran. Conclusion: According to the findings, this test can be used for the disorders in eye-hand coordination, the identification of children with disorders in visual – motor skills. It can also be used for the documentation of the development of fine – motor skills specially in visual – motor skills in 3-14 years – old children.

Interim status report on the revision of ASME PTC 12.1 -- closed feedwater heaters

International Nuclear Information System (INIS)

Stellern, J.L.; Hoobler, J.V.; Milton, J.W.; Welch, T.; Kona, C.; Thompson, H.N.; Tsou, J.L.

1993-01-01

The ASME Performance Test Code (PTC) 12.1-1978 for the performance testing of feedwater heaters is being revised extensively and updated. The committee anticipates that the final draft of the proposed Code will be ready for industry review in 1993. This Code revision will greatly enhance the usefulness and cost effectiveness of feedwater heater performance testing. This paper has been prepared to report on the progress of the committee and to disseminate information on the nature of the revision. Included in this paper are some of the notable changes intended for the Code. The most extensive change is the calculation method, which is described in step-by-step detail. An approach is also described for using ultrasonic flow techniques to test individual or split-string feedwater heaters, when flow nozzles are not available. Additionally some educational information on the use and limitations of ultrasonic measurement instrumentation is included. Discussion is also included on the required uncertainty analysis. 3 refs., 2 figs., 2 tabs

History of personal dosimetry performance testing in the United States

International Nuclear Information System (INIS)

Soares, C. G.

2007-01-01

The basis for personal dosimetry performance testing in the United States is ANSI/HPS N13.11 (2001). Now in its third edition, this standard has been in place since 1983. Testing under this standard is administered by the National Voluntary Accreditation Program (NVLAP), and accreditation of dosimetry processors under this program is required by US Nuclear Regulatory Commission (NRC) regulations. The US Dept. of Energy (DOE) also maintains a testing program for its laboratories and contractors, administered by the Dept. of Energy Laboratory Accreditation Program (DOELAP). A focus in recent years has been the modification of ANSI/HPS N13.11 to allow acceptance by both testing programs in order to bring harmonisation to US personal dosemeter processing testing. Since there is no type testing program in the US for personal dosemeters, the testing philosophy of ANSI N13.11 has always combined elements of type testing and routine performance testing. This philosophy is explored in detail in this presentation, along with trends in the development of the document to its present state. In addition, a look will be taken at what the future holds for the next revision of the document, scheduled to begin in 2005. (authors)

The Bulimia Test--Revised: Validation with "DSM-IV" Criteria for Bulimia Nervosa.

Science.gov (United States)

Thelen, Mark H.; And Others

1996-01-01

The Bulimia Test--Revised (BULIT-R) was given to 23 female subjects who met the criteria for bulimia in the "Diagnostic and Statistical Manual of Mental Disorders" (DSM-IV) and 124 female controls. The BULIT-R appears to be a valid instruction for identifying individuals who meet DSM-IV criteria for bulimia. (SLD)

Safety assessment for the 118-B-1 Burial Ground excavation treatability tests. Revision 2

International Nuclear Information System (INIS)

Zimmer, J.J.; Frain, J.M.

1994-12-01

This revision of the Safety Assessment provides an auditable safety analysis of the hazards for the proposed treatability test activities per DOE-EM-STD-5502-94, DOE Limited Standard, Hazard Baseline Documentation (DOE 1994). The proposed activities are classified as radiological activities and as such, no longer require Operational Safety Limits (OSLs). The OSLS, Prudent Actions, and Institutional and Organization Controls have been removed from this revision and replaced with ''Administrative Actions Important to Safety,'' as determined by the hazards analysis. Those Administrative Actions Important to Safety are summarized in Section 1.1, ''Assessment Summary.''

How explicit and implicit test instructions in an implicit learning task affect performance.

Directory of Open Access Journals (Sweden)

Arnaud Witt

Full Text Available Typically developing children aged 5 to 8 years were exposed to artificial grammar learning. Following an implicit exposure phase, half of the participants received neutral instructions at test while the other half received instructions making a direct, explicit reference to the training phase. We first aimed to assess whether implicit learning operated in the two test conditions. We then evaluated the differential impact of age on learning performances as a function of test instructions. The results showed that performance did not vary as a function of age in the implicit instructions condition, while age effects emerged when explicit instructions were employed at test. However, performance was affected differently by age and the instructions given at test, depending on whether the implicit learning of short or long units was assessed. These results suggest that the claim that the implicit learning process is independent of age needs to be revised.

European wind turbine testing procedure developments. Task 1: Measurement method to verify wind turbine performance characteristics

Energy Technology Data Exchange (ETDEWEB)

Hunter, R.; Friis Pedersen, T.; Dunbabin, P.; Antoniou, I.; Frandsen, S.; Klug, H.; Albers, A.; Lee, W.K.

2001-01-01

There is currently significant standardisation work ongoing in the context of wind farm energy yield warranty assessment and wind turbine power performance testing. A standards maintenance team is revising the current IEC (EN) 61400-12 Ed 1 standard for wind turbine power performance testing. The standard is being divided into four documents. Two of them are drafted for evaluation and verification of complete wind farms and of individual wind turbines within wind farms. This document, and the project it describes, has been designed to help provide a solid technical foundation for this revised standard. The work was wide ranging and addressed 'grey' areas of knowledge, regarding existing methodologies or to carry out basic research in support of fundamentally new procedures. The work has given rise to recommendations in all areas of the work, including site calibration procedures, nacelle anemometry, multi-variate regression analysis and density normalisation. (au)

Comparison of the Reading Subtests of the Wechsler Individual Achievement Test-Third Edition and the Peabody Individual Achievement Test-Revised/Normative Update

Science.gov (United States)

Ott, Lauren M.

2010-01-01

This study compared the reading subtests of the Wechsler Individual Achievement Test-Third Edition and the Peabody Individual Achievement Test-Revised/Normative Update. Scores were compared on these two tests in a group of 28 students ages 7 through 12 who were referred or reevaluated for suspected learning problems. The data were collected…

A Confirmatory Factor Analysis of the Life Orientation Test-Revised with Competitive Athletes

Science.gov (United States)

Appaneal, Renee N.

2012-01-01

Current reviews outside of sport indicate that the Life Orientation Test-Revised (LOT-R) items load on two separate factors (optimism and pessimism) and, therefore, should be treated as independent constructs. However, researchers in the sport sciences continue to use the single composite score reflecting a unidimensional definition of optimism.…

Reliability and validity of the revised Gibson Test of Cognitive Skills, a computer-based test battery for assessing cognition across the lifespan.

Science.gov (United States)

Moore, Amy Lawson; Miller, Terissa M

2018-01-01

The purpose of the current study is to evaluate the validity and reliability of the revised Gibson Test of Cognitive Skills, a computer-based battery of tests measuring short-term memory, long-term memory, processing speed, logic and reasoning, visual processing, as well as auditory processing and word attack skills. This study included 2,737 participants aged 5-85 years. A series of studies was conducted to examine the validity and reliability using the test performance of the entire norming group and several subgroups. The evaluation of the technical properties of the test battery included content validation by subject matter experts, item analysis and coefficient alpha, test-retest reliability, split-half reliability, and analysis of concurrent validity with the Woodcock Johnson III Tests of Cognitive Abilities and Tests of Achievement. Results indicated strong sources of evidence of validity and reliability for the test, including internal consistency reliability coefficients ranging from 0.87 to 0.98, test-retest reliability coefficients ranging from 0.69 to 0.91, split-half reliability coefficients ranging from 0.87 to 0.91, and concurrent validity coefficients ranging from 0.53 to 0.93. The Gibson Test of Cognitive Skills-2 is a reliable and valid tool for assessing cognition in the general population across the lifespan.

Can trained lay providers perform HIV testing services? A review of national HIV testing policies.

Science.gov (United States)

Flynn, David E; Johnson, Cheryl; Sands, Anita; Wong, Vincent; Figueroa, Carmen; Baggaley, Rachel

2017-01-04

Only an estimated 54% of people living with HIV are aware of their status. Despite progress scaling up HIV testing services (HTS), a testing gap remains. Delivery of HTS by lay providers may help close this testing gap, while also increasing uptake and acceptability of HIV testing among key populations and other priority groups. 50 National HIV testing policies were collated from WHO country intelligence databases, contacts and testing program websites. Data regarding lay provider use for HTS was extracted and collated. Our search had no geographical or language restrictions. This data was then compared with reported data from the Global AIDS Response Progress Reporting (GARPR) from July 2015. Forty-two percent of countries permit lay providers to perform HIV testing and 56% permit lay providers to administer pre-and post-test counseling. Comparative analysis with GARPR found that less than half (46%) of reported data from countries were consistent with their corresponding national HIV testing policy. Given the low uptake of lay provider use globally and their proven use in increasing HIV testing, countries should consider revising policies to support lay provider testing using rapid diagnostic tests.

Detailed analysis of the Japanese version of the Rapid Dementia Screening Test, revised version.

Science.gov (United States)

Moriyama, Yasushi; Yoshino, Aihide; Muramatsu, Taro; Mimura, Masaru

2017-11-01

The number-transcoding task on the Japanese version of the Rapid Dementia Screening Test (RDST-J) requires mutual conversion between Arabic and Chinese numerals (209 to , 4054 to , to 681, to 2027). In this task, question and answer styles of Chinese numerals are written horizontally. We investigated the impact of changing the task so that Chinese numerals are written vertically. Subjects were 211 patients with very mild to severe Alzheimer's disease and 42 normal controls. Mini-Mental State Examination scores ranged from 26 to 12, and Clinical Dementia Rating scores ranged from 0.5 to 3. Scores of all four subtasks of the transcoding task significantly improved in the revised version compared with the original version. The sensitivity and specificity of total scores ≥9 on the RDST-J original and revised versions for discriminating between controls and subjects with Clinical Dementia Rating scores of 0.5 were 63.8% and 76.6% on the original and 60.1% and 85.8% on revised version. The revised RDST-J total score had low sensitivity and high specificity compared with the original RDST-J for discriminating subjects with Clinical Dementia Rating scores of 0.5 from controls. © 2017 Japanese Psychogeriatric Society.

Pending revisions to ANS 56.8-81 containment systems leakage testing requirements

International Nuclear Information System (INIS)

Brown, T.M.

1986-01-01

The US Nuclear Regulatory Commission is currently processing a revision to Appendix J of Part 50, Title 10 of the Code of Federal Regulations. The revised Appendix J will not reference any ANSI standard. Processed concurrently with the revised Appendix J is a draft Regulatory Guide which does endorse ANS Standard 56.8. The draft Regulatory Guide currently takes many exceptions to the Standard. Many of the exceptions are changes the Working Group had in process and the exceptions are to bring the draft Regulatory Guide in line with the future Standard. The Working Group has completed their revisions to the Standard and its appendices. These revisions have been submitted to the Nuclear Power Plants Standards Committee (NUPPSCO). The NUPPSCO comments have recently been addressed by the Working Group and the Working Group response has been sent to the NUPPSCO commentators. This paper will discuss the revisions made to the Standard, the significance of the revisions and future tasks or Standard revisions which the ANS 56.8 Working Group may address

Circumcision revision in male children

Directory of Open Access Journals (Sweden)

Mohammed A. Al-Ghazo

2006-08-01

Full Text Available OBJECTIVE: To determine indications for circumcision revision and to identify the specialty of the person who performed unsatisfactory primary circumcision. MATERIALS AND METHODS: The authors reviewed medical records of 52 cases that underwent circumcision revision over a 6-year period (1998 to 2004. Sleeve surgical technique was used for revision in patients with redundant foreskin or concealed penis, penoplasty for partial or complete degloving of the penis and meatotomy for external meatal stenosis. The mean age of children was 32 months (range 6 months to 9 years. RESULTS: Most of unsatisfactory primary circumcisions (86.7% were performed by laymen. All patients who underwent circumcision revision had good to excellent cosmetic results. CONCLUSION: Primary circumcision performed by laymen carry a high complication rate and serious complications may occur. A period of training and direct supervision by physicians is required before allowing laymen to perform circumcision independently.

Revision of the SNPforID 34-plex forensic ancestry test: Assay enhancements, standard reference sample genotypes and extended population studies.

Science.gov (United States)

Fondevila, M; Phillips, C; Santos, C; Freire Aradas, A; Vallone, P M; Butler, J M; Lareu, M V; Carracedo, A

2013-01-01

A revision of an established 34 SNP forensic ancestry test has been made by swapping the under-performing rs727811 component SNP with the highly informative rs3827760 that shows a near-fixed East Asian specific allele. We collated SNP variability data for the revised SNP set in 66 reference populations from 1000 Genomes and HGDP-CEPH panels and used this as reference data to analyse four U.S. populations showing a range of admixture patterns. The U.S. Hispanics sample in particular displayed heterogeneous values of co-ancestry between European, Native American and African contributors, likely to reflect in part, the way this disparate group is defined using cultural as well as population genetic parameters. The genotyping of over 700 U.S. population samples also provided the opportunity to thoroughly gauge peak mobility variation and peak height ratios observed from routine use of the single base extension chemistry of the 34-plex test. Finally, the genotyping of the widely used DNA profiling Standard Reference Material samples plus other control DNAs completes the audit of the 34-plex assay to allow forensic practitioners to apply this test more readily in their own laboratories. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Periodical test program in depth revision

International Nuclear Information System (INIS)

Feltin, C.; Zermizoglou, R.

1987-11-01

Inspection visits made to different sites during 1980 and 1981 evidenced the need to extend and define more precisely the periodical tests performed on safety related systems; thus Electricite de France was requested by the Safety Authorities to re-examine the periodical test program for all safety related systems. This paper presents the methodology adopted by Electricite de France in order to perform an exhaustive analysis of the periodical test program for the 900 and 1300 MWe plants, and the organization set up at the IPSN at one hand and Electricite de France on the other hand for the purpose of elaborating a periodical test program which would be ratified by the Safety Authorities

The mechanical effect of the existing cement mantle on the in-cement femoral revision.

Science.gov (United States)

Keeling, Parnell; Lennon, Alexander B; Kenny, Patrick J; O'Reilly, Peter; Prendergast, Patrick J

2012-08-01

Cement-in-cement revision hip arthroplasty is an increasingly popular technique to replace a loose femoral stem which retains much of the original cement mantle. However, some concern exists regarding the retention of the existing fatigued and aged cement in such cement-in-cement revisions. This study investigates whether leaving an existing fatigued and aged cement mantle degrades the mechanical performance of a cement-in-cement revision construct. Primary cement mantles were formed by cementing a polished stem into sections of tubular steel. If in the test group, the mantle underwent conditioning in saline to simulate ageing and was subject to a fatigue of 1 million cycles. If in the control group no such conditioning or fatigue was carried out. The cement-in-cement procedure was then undertaken. Both groups underwent a fatigue of 1 million cycles subsequent to the revision procedure. Application of a Mann-Whitney test on the recorded subsidence (means: 0.51, 0.46, n=10+10, P=0.496) and inducible displacement (means: 0.38, 0.36, P=0.96) revealed that there was no statistical difference between the groups. This study represents further biomechanical investigation of the mechanical behaviour of cement-in-cement revision constructs. Results suggest that pre-revision fatigue and ageing of the cement may not be deleterious to the mechanical performance of the revision construct. Thus, this study provides biomechanical evidence to back-up recent successes with this useful revision technique. Copyright © 2012 Elsevier Ltd. All rights reserved.

Impact of the Revised Malaysian Code on Corporate Governance on Audit Committee Attributes and Firm Performance

OpenAIRE

KALLAMU, Basiru Salisu

2016-01-01

Abstract. Using a sample of 37 finance companies listed under the finance segment of Bursa Malaysia, we examined the impact of the revision to Malaysian code on corporate governance on audit committee attributes and firm performance. Our result suggests that audit committee attributes significantly improved after the Code was revised. In addition, the coefficient for audit committee and risk committee interlock has a significant negative relationship with Tobin’s Q in the period before the re...

One-stage Revision ACL reconstruction with hamstring autograft results in satisfactory outcome

Science.gov (United States)

Kejriwal, Ritwik; Buelow, Jens

2017-01-01

Objectives: Revision anterior cruciate ligament (ACL) reconstruction is associated with poorer outcomes and higher rerupture rates when compared to primary ACL reconstruction. There is also a significant heterogeneity in surgical technique, number of stages, and graft options. We report a large single surgeon case series with hamstring autograft as a graft option. Methods: Observational series of revision ACL reconstructions performed by the senior author between 2005 and 2015 was carried out. Chart reviews and clinic follow-ups were performed with the following recorded – re-rupture rate, radiographic grading of osteoarthritis, KT-1000 arthrometer test, IKDC outcome scores and knee range of motion. All patients underwent single bundle four-strand hamstring autograft performed in one stage with use of new tunnels in majority of the cases. Results: 66 patients underwent hamstring autograft one-stage revision ACL reconstruction by Dr Jens Buelow. Chart review was carried out on all patients, and 26 (39%) were followed up in clinic and/or by phone with a mean follow up of 4.7 years. Outcomes included re-rupture rate of 4.5%, reoperation rate of 12%, mean visual analogue scale score of 7.6, mean side-to-side difference of 2.6 mm for KT-1000 arthrometer test, and mean IKDC score of 79. Of the 17 patients with radiographs, 40% had moderate osteoarthritis (grade 2 or 3) at follow-up. Conclusion: Revision ACL reconstruction can result in a satisfactory outcome when performed with a hamstring autograft in one stage.

Test Standard Revision Update: JESD57, "Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation"

Science.gov (United States)

Lauenstein, Jean-Marie

2015-01-01

The JEDEC JESD57 test standard, Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation, is undergoing its first revision since 1996. In this talk, we place this test standard into context with other relevant radiation test standards to show its importance for single-event effect radiation testing for space applications. We show the range of industry, government, and end-user party involvement in the revision. Finally, we highlight some of the key changes being made and discuss the trade-space in which setting standards must be made to be both useful and broadly adopted.

75 FR 47592 - Final Test Guideline; Product Performance of Skin-applied Insect Repellents of Insect and Other...

Science.gov (United States)

2010-08-06

.... Crystal Dr., Arlington, VA. The hours of operation of this Docket Facility are from 8:30 a.m. to 4 p.m... has been working to revise this Product Performance Test Guideline since it was published as a... further strengthening the scientific and ethical conduct of this kind of research; these have been...

Nursing Faculty Decision Making about Best Practices in Test Construction, Item Analysis, and Revision

Science.gov (United States)

Killingsworth, Erin Elizabeth

2013-01-01

With the widespread use of classroom exams in nursing education there is a great need for research on current practices in nursing education regarding this form of assessment. The purpose of this study was to explore how nursing faculty members make decisions about using best practices in classroom test construction, item analysis, and revision in…

Project W-320, operational test procedure OTP-320-003 test report

International Nuclear Information System (INIS)

Bevins, R.R.

1998-01-01

This report documents and summarizes the results of OTP-320-003 Project W-320 Operational Testing of the WRSS Supernate Transfer System. Project W-320 Operational Test OTP-320-003 was performed to verify components of the Waste Retrieval Sluicing System (WRSS) supernate transfer system functioned as designed following construction completion and turnover to operations. All equipment operation was performed by Tank Farms Operations personnel following the operational test procedure and referenced operating procedures. Supernate Transfer line Flushing System Testing was completed over the course of approximately 4 weeks as tank farm conditions and configuration, equipment availability, and operations resources allowed. All testing was performed with the 702-AZ ventilation system and the 296-P-16 ventilation systems in operation. Test procedure OTP-320-003 required two revisions during testing to incorporate Procedure Changes Authorizations (PCAs) necessary to facilitate testing. Various sections of testing are documented on each procedure revision. The completed test procedure is included as Attachment A. Exception Reports generated during the course of testing are included as Attachment B

Revision of ISO 15859 Aerospace Fluid Standards

Science.gov (United States)

Greene, Benjamin; McClure, Mark B.

2012-01-01

A detailed review of ISO 15859 "Space Systems - Fluid Characteristics, Sampling and Test Methods" was performed An approach to revising Parts 1-9 and 11-13 was developed and concurred by the NASA Technical Standards Program Office. The approach was to align them with the highest level source documents, and not to program-specific requirements. The updated documents were prepared and presented.

Relationship between self-reported cognitive difficulties, objective neuropsychological test performance and psychological distress in chronic pain.

Science.gov (United States)

Baker, K S; Gibson, S J; Georgiou-Karistianis, N; Giummarra, M J

2018-03-01

Persons with chronic pain often report problems with cognitive abilities, such as memory or attention. There is limited understanding of whether objective performance is consistent with subjective reports, and how psychological factors contribute. We aimed to investigate these relationships in a group of patients expressing cognitive concerns, and evaluate the utility of self-report tools for pain management settings. Participants with chronic pain (n = 41) completed standardized neuropsychological tests, and self-report measures of cognitive functioning, pain, mood and sleep, as part of a broader study investigating cognitive performance in pain. Average neuropsychological test performance was subtly below normative means (within one standard deviation). Twenty-five percent of the sample scored substantially below age-adjusted norms on one or more objective tests. There were moderate-to-large associations between objective performance (e.g. Trail-Making B) and subjective cognitive complaints (e.g. Everyday Memory Questionnaire - Revised), controlling for age and education level. This was moderated by anxiety, such that subjective-objective relationships were particularly strong in those with higher anxiety. Poorer test performance was associated with higher pain intensity and catastrophizing. Subjective-objective cognition relationships remained after controlling for catastrophizing. Patients' self-reported cognitive concerns concurred with objectively measured performance, independent of age, education and catastrophizing. Moreover, those with severe anxiety were more accurate in predicting their cognitive performance. The findings highlight some interesting cognition-mood relationships, and suggest that easy-to-administer questionnaires, such as the Everyday Memory Questionnaire - Revised and the Behavior Rating Inventory of Executive Function - Adult Version, may be useful to capture cognitive concerns in clinical settings. Cognitive concerns in chronic pain

Saudi normative data for the Wisconsin Card Sorting test, Stroop test, Test of Non-verbal Intelligence-3, Picture Completion and Vocabulary (subtest of the Wechsler Adult Intelligence Scale-Revised).

Science.gov (United States)

Al-Ghatani, Ali M; Obonsawin, Marc C; Binshaig, Basmah A; Al-Moutaery, Khalaf R

2011-01-01

There are 2 aims for this study: first, to collect normative data for the Wisconsin Card Sorting Test (WCST), Stroop test, Test of Non-verbal Intelligence (TONI-3), Picture Completion (PC) and Vocabulary (VOC) sub-test of the Wechsler Adult Intelligence Scale-Revised for use in a Saudi Arabian culture, and second, to use the normative data provided to generate the regression equations. To collect the normative data and generate the regression equations, 198 healthy individuals were selected to provide a representative distribution for age, gender, years of education, and socioeconomic class. The WCST, Stroop test, TONI-3, PC, and VOC were administrated to the healthy individuals. This study was carried out at the Department of Clinical Neurosciences, Riyadh Military Hospital, Riyadh, Kingdom of Saudi Arabia from January 2000 to July 2002. Normative data were obtained for all tests, and tables were constructed to interpret scores for different age groups. Regression equations to predict performance on the 3 tests of frontal function from scores on tests of fluid (TONI-3) and premorbid intelligence were generated from the data from the healthy individuals. The data collected in this study provide normative tables for 3 tests of frontal lobe function and for tests of general intellectual ability for use in Saudi Arabia. The data also provide a method to estimate pre-injury ability without the use of verbally based tests.

Reliability and validity of the revised Gibson Test of Cognitive Skills, a computer-based test battery for assessing cognition across the lifespan

Directory of Open Access Journals (Sweden)

Moore AL

2018-02-01

Full Text Available Amy Lawson Moore, Terissa M Miller Gibson Institute of Cognitive Research, Colorado Springs, CO, USA Purpose: The purpose of the current study is to evaluate the validity and reliability of the revised Gibson Test of Cognitive Skills, a computer-based battery of tests measuring short-term memory, long-term memory, processing speed, logic and reasoning, visual processing, as well as auditory processing and word attack skills.Methods: This study included 2,737 participants aged 5–85 years. A series of studies was conducted to examine the validity and reliability using the test performance of the entire norming group and several subgroups. The evaluation of the technical properties of the test battery included content validation by subject matter experts, item analysis and coefficient alpha, test–retest reliability, split-half reliability, and analysis of concurrent validity with the Woodcock Johnson III Tests of Cognitive Abilities and Tests of Achievement.Results: Results indicated strong sources of evidence of validity and reliability for the test, including internal consistency reliability coefficients ranging from 0.87 to 0.98, test–retest reliability coefficients ranging from 0.69 to 0.91, split-half reliability coefficients ranging from 0.87 to 0.91, and concurrent validity coefficients ranging from 0.53 to 0.93.Conclusion: The Gibson Test of Cognitive Skills-2 is a reliable and valid tool for assessing cognition in the general population across the lifespan. Keywords: testing, cognitive skills, memory, processing speed, visual processing, auditory processing

A test of Hartnett's revisions to the pubic symphysis and fourth rib methods on a modern sample.

Science.gov (United States)

Merritt, Catherine E

2014-05-01

Estimating age at death is one of the most important aspects of creating a biological profile. Most adult age estimation methods were developed on North American skeletal collections from the early to mid-20th century, and their applicability to modern populations has been questioned. In 2010, Hartnett used a modern skeletal collection from the Maricopia County Forensic Science Centre to revise the Suchey-Brooks pubic symphysis method and the İşcan et al. fourth rib methods. The current study tests Hartnett's revised methods as well as the original Suchey-Brooks and İşcan et al. methods on a modern sample from the William Bass Skeletal Collection (N = 313, mean age = 58.5, range 19-92). Results show that the Suchey-Brooks and İşcan et al. methods assign individuals to the correct phase 70.8% and 57.5% of the time compared with Hartnett's revised methods at 58.1% and 29.7%, respectively, with correctness scores based on one standard deviation of the mean rather than the entire age range. Accuracy and bias scores are significantly improved for Hartnett's revised pubic symphysis method and marginally better for Hartnett's revised fourth rib method, suggesting that the revised mean ages at death of Hartnett's phases better reflect this modern population. Overall, both Hartnett's revised methods are reliable age estimation methods. For the pubic symphysis, there are significant improvements in accuracy and bias scores, especially for older individuals; however, for the fourth rib, the results are comparable to the original İşcan et al. methods, with some improvement for older individuals. © 2014 American Academy of Forensic Sciences.

Revision total hip arthoplasty: factors associated with re-revision surgery.

Science.gov (United States)

Khatod, Monti; Cafri, Guy; Inacio, Maria C S; Schepps, Alan L; Paxton, Elizabeth W; Bini, Stefano A

2015-03-04

The survivorship of implants after revision total hip arthroplasty and risk factors associated with re-revision are not well defined. We evaluated the re-revision rate with use of the institutional total joint replacement registry. The purpose of this study was to determine patient, implant, and surgeon factors associated with re-revision total hip arthroplasty. A retrospective cohort study was conducted. The total joint replacement registry was used to identify patients who had undergone revision total hip arthroplasty for aseptic reasons from April 1, 2001, to December 31, 2010. The end point of interest was re-revision total hip arthroplasty. Risk factors evaluated for re-revision total hip arthroplasty included: patient risk factors (age, sex, body mass index, race, and general health status), implant risk factors (fixation type, bearing surface, femoral head size, and component replacement), and surgeon risk factors (volume and experience). A multivariable Cox proportional hazards model was used. Six hundred and twenty-nine revision total hip arthroplasties with sixty-three (10%) re-revisions were evaluated. The mean cohort age (and standard deviation) was 57.0 ± 12.4 years, the mean body mass index (and standard deviation) was 29.5 ± 6.1 kg/m(2), and most of the patients were women (64.5%) and white (81.9%) and had an American Society of Anesthesiologists score of associated with the risk of re-revision. For every ten-year increase in patient age, the hazard ratio for re-revision decreases by a factor of 0.72 (95% confidence interval, 0.58 to 0.90). For every five revision surgical procedures performed by a surgeon, the risk of revision decreases by a factor of 0.93 (95% confidence interval, 0.86 to 0.99). At the time of revision, a new or retained cemented femoral implant or all-cemented hip implant increases the risk of revision by a factor of 3.19 (95% confidence interval, 1.22 to 8.38) relative to a retained or new uncemented hip implant. A ceramic on a

The revised Generalized Expectancy for Success Scale: a validity and reliability study.

Science.gov (United States)

Hale, W D; Fiedler, L R; Cochran, C D

1992-07-01

The Generalized Expectancy for Success Scale (GESS; Fibel & Hale, 1978) was revised and assessed for reliability and validity. The revised version was administered to 199 college students along with other conceptually related measures, including the Rosenberg Self-Esteem Scale, the Life Orientation Test, and Rotter's Internal-External Locus of Control Scale. One subsample of students also completed the Eysenck Personality Inventory, while another subsample performed a criterion-related task that involved risk taking. Item analysis yielded 25 items with correlations of .45 or higher with the total score. Results indicated high internal consistency and test-retest reliability.

Revised Rules for Concrete Bridges

DEFF Research Database (Denmark)

Thoft-Christensen, Palle; Jensen, F. M.; Middleton, C.

This paper is based on research performed for the Highway Agency, London, UK under the project DPU/9/44 "Revision of Bridge Assessment Rules Based on Whole Life Performance: Concrete Bridges" It contains details of a methodology which can be used to generate Whole Life (WL) reliability profiles....... These WL reliability profiles may be used to establish revised rules for Concrete Bridges....

Test plan for determining breathing rates in single shell tanks using tracer gases. Revision 1

International Nuclear Information System (INIS)

Andersen, J.A.

1997-01-01

This test plan specifies the requirements and conditions for the injection of tracer gas (Helium (He)) into single shell tanks to determine breathing rates using periodic sampling. The eight tanks which have been selected at the time this Test Plan was developed are A-101, AX-102, AX-103, BY-105, C-107, U-103 (U-103 is counted twice, once during the winter months and once during the summer), and U-105. Other tanks to be sampled will be assigned by Pacific Northwest National Laboratory (PNNL) at a later date in the study process as resources allow, the document shall be revised as required. The sampling of headspace for each of these tanks shall be performed using available risers or the Standard Hydrogen Monitoring System (SHMS) cabinet as available. The tank farm vapor cognizant engineer shall assign the injection and sample testing point for each tank and document the point in the field work package. SUMMA TMI canisters, equipped in-line with dual particulate air filters and two silica gel sorbent traps will be used to collect the gas samples. The purpose of dual particulate air filters is to ensure no radioactive particulates are transferred to the SUMMA TMI canisters. The silica gel sorbent traps will effectively eliminate any tritiated water vapor that may be present in the sample gas stream. PNNL shall supply the tracer gases injection system and shall perform the analysis on the headspace samples. TWRS Characterization project shall inject the tracer gas and perform the sampling. Refer to Engineering Task Plan HNF-SD-TWR-ETP-002 for a detailed description of the responsibilities for this task

Comparison of Individual Performance in Intelligence Tests WAIS III and RPM (Raven's Progressive Matrices)

OpenAIRE

Petrů, Vít

2017-01-01

This thesis deals with replacement of performative scale of Wechsler Adult Intelligence Scale (3rd revision) through Raven's Standard Progressive Matrices and Advanced Progressive Matrices. In the theoretical part introduces the concepts of intelligence, approaches to its exploration and intelligence tests. The theoretical part is also devoted to the description of the used methods and presents an overview of the research on a similar theme as this work. In the empirical part of the thesis is...

Understanding protocol performance: impact of test performance.

Science.gov (United States)

Turner, Robert G

2013-01-01

This is the second of two articles that examine the factors that determine protocol performance. The objective of these articles is to provide a general understanding of protocol performance that can be used to estimate performance, establish limits on performance, decide if a protocol is justified, and ultimately select a protocol. The first article was concerned with protocol criterion and test correlation. It demonstrated the advantages and disadvantages of different criterion when all tests had the same performance. It also examined the impact of increasing test correlation on protocol performance and the characteristics of the different criteria. To examine the impact on protocol performance when individual tests in a protocol have different performance. This is evaluated for different criteria and test correlations. The results of the two articles are combined and summarized. A mathematical model is used to calculate protocol performance for different protocol criteria and test correlations when there are small to large variations in the performance of individual tests in the protocol. The performance of the individual tests that make up a protocol has a significant impact on the performance of the protocol. As expected, the better the performance of the individual tests, the better the performance of the protocol. Many of the characteristics of the different criteria are relatively independent of the variation in the performance of the individual tests. However, increasing test variation degrades some criteria advantages and causes a new disadvantage to appear. This negative impact increases as test variation increases and as more tests are added to the protocol. Best protocol performance is obtained when individual tests are uncorrelated and have the same performance. In general, the greater the variation in the performance of tests in the protocol, the more detrimental this variation is to protocol performance. Since this negative impact is increased as

Validation of the Snijders-Oomen Nonverbal Intelligence Test-Revised 2 1/2-7 for Australian children with disabilities

NARCIS (Netherlands)

Jenkinson, J; Roberts, S; Dennehy, S; Tellegen, P.J.

One hundred and fifty-five preschool children (59 with hearing impairment, 37 with developmental delay, and 59 nondisabled children) were tested with the Snijders-Oomen Nonverbal Intelligence Test - Revised (2 1/2 - 7) (SON-R 2 1/2 - 7) and the Wechsler Preschool and Primary Scale of Intelligence -

Underground Test Area Fiscal Year 2012 Annual Quality Assurance Report Nevada National Security Site, Nevada, Revision 0

Energy Technology Data Exchange (ETDEWEB)

Farnham, Irene [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States); Marutzky, Sam [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

2013-01-01

This report is mandated by the Underground Test Area (UGTA) Quality Assurance Project Plan (QAPP) and identifies the UGTA quality assurance (QA) activities for fiscal year (FY) 2012. All UGTA organizations—U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO); Desert Research Institute (DRI); Lawrence Livermore National Laboratory (LLNL); Los Alamos National Laboratory (LANL); Navarro-Intera, LLC (N-I); National Security Technologies, LLC (NSTec); and the U.S. Geological Survey (USGS)—conducted QA activities in FY 2012. The activities included conducting assessments, identifying findings and completing corrective actions, evaluating laboratory performance, revising the QAPP, and publishing documents. In addition, processes and procedures were developed to address deficiencies identified in the FY 2011 QAPP gap analysis.

easyCBM CCSS Math Item Scaling and Test Form Revision (2012-2013): Grades 6-8. Technical Report #1313

Science.gov (United States)

Anderson, Daniel; Alonzo, Julie; Tindal, Gerald

2012-01-01

The purpose of this technical report is to document the piloting and scaling of new easyCBM mathematics test items aligned with the Common Core State Standards (CCSS) and to describe the process used to revise and supplement the 2012 research version easyCBM CCSS math tests in Grades 6-8. For all operational 2012 research version test forms (10…

Expedited technology demonstration project (Revised mixed waste management facility project) Project baseline revision 4.0 and FY98 plan

International Nuclear Information System (INIS)

Adamson, M. G.

1997-01-01

The re-baseline of the Expedited Technology Demonstration Project (Revised Mixed Waste Facility Project) is designated as Project Baseline Revision 4.0. The last approved baseline was identified as Project Baseline Revision 3.0 and was issued in October 1996. Project Baseline Revision 4.0 does not depart from the formal DOE guidance followed by, and contained in, Revision 3.0. This revised baseline document describes the MSO and Final Forms testing activities that will occur during FY98, the final year of the ETD Project. The cost estimate for work during FY98 continues to be $2.OM as published in Revision 3.0. However, the funds will be all CENRTC rather than the OPEX/CENTRC split previously anticipated. LLNL has waived overhead charges on ETD Project CENRTC funds since the beginning of project activities. By requesting the $2.OM as all CENTRC a more aggressive approach to staffing and testing can be taken. Due to a cost under- run condition during FY97 procurements were made and work was accomplished, with the knowledge of DOE, in the Feed Preparation and Final Forms areas that were not in the scope of Revision 3.0. Feed preparation activities for FY98 have been expanded to include the drum opening station/enclosure previously deleted

Comparison of revision strategies for failed C2-posterior cervical pedicle screws: a biomechanical study.

Science.gov (United States)

Mayer, Michael; Zenner, Juliane; Bogner, Robert; Hitzl, Wolfgang; Figl, Markus; von Keudell, Arvind; Stephan, Daniel; Penzkofer, Rainer; Augat, Peter; Korn, Gundobert; Resch, Herbert; Koller, Heiko

2013-01-01

With increasing usage within challenging biomechanical constructs, failures of C2 posterior cervical pedicle screws (C2-pCPSs) will occur. The purpose of the study was therefore to investigate the biomechanical characteristics of two revision techniques after the failure of C2-pCPSs. Twelve human C2 vertebrae were tested in vitro in a biomechanical study to compare two strategies for revision screws after failure of C2-pCPSs. C2 pedicles were instrumented using unicortical 3.5-mm CPS bilaterally (Synapse/Synthes, Switzerland). Insertion accuracy was verified by fluoroscopy. C2 vertebrae were potted and fixed in an electromechanical testing machine with the screw axis coaxial to the pullout direction. Pullout testing was conducted with load and displacement data taken continuously. The peak load to failure was measured in newtons (N) and is reported as the pullout resistance (POR). After pullout, two revision strategies were tested in each vertebra. In Group-1, revision was performed with 4.0-mm C2-pCPSs. In Group-2, revision was performed with C2-pedicle bone-plastic combined with the use of a 4-mm C2-pCPSs. For the statistical analysis, the POR between screws was compared using absolute values (N) and the POR of the revision techniques normalized to that of the primary procedures (%). The POR of primary 3.5-mm CPSs was 1,140.5 ± 539.6 N for Group-1 and 1,007.7 ± 362.5 N for Group-2; the difference was not significant. In the revision setting, the POR in Group-1 was 705.8 ± 449.1 N, representing a reduction of 38.1 ± 32.9 % compared with that of primary screw fixation. For Group-2, the POR was 875.3 ± 367.9 N, representing a reduction of 13.1 ± 23.4 %. A statistical analysis showed a significantly higher POR for Group-2 compared with Group-1 (p = 0.02). Although the statistics showed a significantly reduced POR for both revision strategies compared with primary fixation (p plastic, the POR can be significantly increased compared with the use of only an

Diet History Questionnaire: Database Revision History

Science.gov (United States)

The following details all additions and revisions made to the DHQ nutrient and food database. This revision history is provided as a reference for investigators who may have performed analyses with a previous release of the database.

Validation of the Turkish Version of the Cognitive Test Anxiety Scale–Revised

Directory of Open Access Journals (Sweden)

Sati Bozkurt

2017-01-01

Full Text Available The current study explored the psychometric properties of the newly designed Turkish version of the Cognitive Test Anxiety Scale–Revised (CTAR. Results of an exploratory factor analysis revealed an unidimensional structure consistent with the conceptualized nature of cognitive test anxiety and previous examinations of the English version of the CTAR. Examination of the factor loadings revealed two items that were weakly related to the test anxiety construct and as such were prime candidates for removal. Confirmatory factor analyses were conducted to compare model fit for the 25- and 23-item version of the measure. Results indicated that the 23-item version of the measure provided a better fit to the data which support the removal of the problematic items in the Turkish version of the CTAR. Additional analyses demonstrated the internal consistency, test–retest reliability, concurrent validity, and gender equivalence for responses offered on the Turkish version of the measure. Results of the analysis revealed a 23-item Turkish version of the T-CTAR is a valid and reliable measure of cognitive test anxiety for use among Turkish students.

Development of turbopump cavitation performance test facility and the test of inducer performance

International Nuclear Information System (INIS)

Sohn, Dong Kee; Kim, Chun Tak; Yoon, Min Soo; Cha, Bong Jun; Kim, Jin Han; Yang, Soo Seok

2001-01-01

A performance test facility for turbopump inducer cavitation was developed and the inducer cavitation performance tests were performed. Major components of the performance test facility are driving unit, test section, piping, water tank, and data acquisition and control system. The maximum of testing capability of this facility are as follows: flow rate - 30kg/s; pressure - 13 bar, rotational speed - 10,000rpm. This cavitation test facility is characterized by the booster pump installed at the outlet of the pump that extends the flow rate range, and by the pressure control system that makes the line pressure down to vapor pressure. The vacuum pump is used for removing the dissolved air in the water as well as the line pressure. Performance tests were carried out and preliminary data of test model inducer were obtained. The cavitation performance test and cavitation bubble flow visualization were also made. This facility is originally designed for turbopump inducer performance test and cavitation test. However it can be applied to the pump impeller performance test in the future with little modification

Clinical relevance of the proposed sexual addiction diagnostic criteria: relation to the Sexual Addiction Screening Test-Revised.

Science.gov (United States)

Carnes, Patrick J; Hopkins, Tiffany A; Green, Bradley A

2014-01-01

The present article examines and compares the various diagnostic rubrics proposed to codify symptoms of sexual addiction, and then briefly summarizes the ongoing controversy on whether sexual addiction is a valid construct. Using the diagnostic criteria proposed by , the prevalence rate of each criterion is examined in terms of scores on the Sexual Addiction Screening Test-Revised scales (). Differences in diagnostic criteria endorsement associated with sex, sexual orientation, and setting were also explored. Results from a clinical sample of men and women seeking treatment for sexual addiction demonstrated clinical relevance of the criteria, in that all but 3 criteria are endorsed at more than 50% of participants screening positive for sexual addiction on the Sexual Addiction Screening Test-Revised. Sex differences were also noted for endorsement rates of several of the criteria. Finally, several proposed criteria may pose a higher clinical threshold and thus be utilized by clinicians to identify patients with increased pathology. Results are discussed in the context of existing diagnostic frameworks across etiological perspectives.

Performance of low-educated elders with depression on Addenbrooke's Cognitive Examination-Revised (ace-r) test

OpenAIRE

Beckert,Michele; Loureiro,Fernanda; Menta,Caroline; Mello,Elisa Fasolin; Nogueira,Eduardo L.; Gunten,Armin von; Gomes,Irênio

2016-01-01

ABSTRACT Along with cognitive disorders, depression has been a concern for mental health services due to its highly debilitating effect on the functioning and quality of life of the elderly. However, there is still little understanding of the cognitive alterations resulting from depression or of the difficult differential diagnosis with mild cognitive impairment (MCI). It is known that performance on cognitive tests is strongly influenced by education but few studies have been conducted invol...

A reliability analysis of the revised competitiveness index.

Science.gov (United States)

Harris, Paul B; Houston, John M

2010-06-01

This study examined the reliability of the Revised Competitiveness Index by investigating the test-retest reliability, interitem reliability, and factor structure of the measure based on a sample of 280 undergraduates (200 women, 80 men) ranging in age from 18 to 28 years (M = 20.1, SD = 2.1). The findings indicate that the Revised Competitiveness Index has high test-retest reliability, high inter-item reliability, and a stable factor structure. The results support the assertion that the Revised Competitiveness Index assesses competitiveness as a stable trait rather than a dynamic state.

Cochlear implant revision surgeries in children.

Science.gov (United States)

Amaral, Maria Stella Arantes do; Reis, Ana Cláudia Mirândola B; Massuda, Eduardo T; Hyppolito, Miguel Angelo

2018-02-16

The surgery during which the cochlear implant internal device is implanted is not entirely free of risks and may produce problems that will require revision surgeries. To verify the indications for cochlear implantation revision surgery for the cochlear implant internal device, its effectiveness and its correlation with certain variables related to language and hearing. A retrospective study of patients under 18 years submitted to cochlear implant Surgery from 2004 to 2015 in a public hospital in Brazil. Data collected were: age at the time of implantation, gender, etiology of the hearing loss, audiological and oral language characteristics of each patient before and after Cochlear Implant surgery and any need for surgical revision and the reason for it. Two hundred and sixty-five surgeries were performed in 236 patients. Eight patients received a bilateral cochlear implant and 10 patients required revision surgery. Thirty-two surgeries were necessary for these 10 children (1 bilateral cochlear implant), of which 21 were revision surgeries. In 2 children, cochlear implant removal was necessary, without reimplantation, one with cochlear malformation due to incomplete partition type I and another due to trauma. With respect to the cause for revision surgery, of the 8 children who were successfully reimplanted, four had cochlear calcification following meningitis, one followed trauma, one exhibited a facial nerve malformation, one experienced a failure of the cochlear implant internal device and one revision surgery was necessary because the electrode was twisted. The incidence of the cochlear implant revision surgery was 4.23%. The period following the revision surgeries revealed an improvement in the subject's hearing and language performance, indicating that these surgeries are valid in most cases. Copyright © 2018 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

Performance-based containment leakage testing

International Nuclear Information System (INIS)

Cybulskis, P.

1995-01-01

The U.S. Nuclear Regulatory Commission (NRC) is reviewing regulatory requirements in an effort to revise those that are marginal to safety but impose significant burdens on licensees. Identification of requirements marginal to safety and development and evaluation of alternatives utilize the NRC safety goals and insights from probabilistic risk assessments (PRAs). Since earlier studies found design-basis containment leakage to be a minor contributor to reactor accident risk, containment leakage testing has been selected as a candidate for change in regulations. This paper summarizes the technical analyses supporting the NRC proposal to amend Appendix J of 10 CFR Part 50 as its first effort to decrease unnecessary regulatory burdens on licensees

Appraising and applying evidence about a diagnostic test during a performance-based assessment

Directory of Open Access Journals (Sweden)

Franklin Ellen

2004-10-01

Full Text Available Abstract Background The practice of Evidence-based Medicine requires that clinicians assess the validity of published research and then apply the results to patient care. We wanted to assess whether our soon-to-graduate medical students could appraise and apply research about a diagnostic test within a clinical context and to compare our students with peers trained at other institutions. Methods 4th year medical students who previously had demonstrated competency at probability revision and just starting first-year Internal Medicine residents were used for this research. Following an encounter with a simulated patient, subjects critically appraised a paper about an applicable diagnostic test and revised the patient's pretest probability given the test result. Results The medical students and residents demonstrated similar skills at critical appraisal, correctly answering 4.7 and 4.9, respectively, of 6 questions (p = 0.67. Only one out of 28 (3% medical students and none of the 15 residents were able to correctly complete the probability revision task (p = 1.00. Conclusions This study found that most students completing medical school are able to appraise an article about a diagnostic test but few are able to apply the information from the article to a patient. These findings raise questions about the clinical usefulness of the EBM skills possessed by graduating medical students within the area of diagnostic testing.

Revised inspection program for nuclear power plants

International Nuclear Information System (INIS)

1978-01-01

The United States Nuclear Regulatory Commission (NRC) regulates nuclear power plants to assure adequate protection of the public and the environment from the dangers associated with nuclear materials. NRC fulfills this responsibility through comprehensive safety reviews of nuclear facilities, licensing of organizations that use nuclear materials, and continuing inspection. The NRC inspection program is currently conducted from the five regional offices in or near Philadelphia, Atlanta, Chicago, Dallas and San Francisco. Inspectors travel from the regional offices to nuclear power plants in various phases of construction, test and operation in order to conduct inspections. However, in June 1977 the Commission approved a revision to the inspection program that will include stationing inspectors at selected plants under construction and at all plants in operation. In addition, the revised program provides for appraising the performance of licensees on a national basis and involves more direct measurement and observation by NRC inspectors of work and tests in progress. The program also includes enhanced career management consisting of improved training and career development for inspectors and other professionals. The report was requested in the Conference Report on the NRC Authorization for Appropriations for Fiscal Year 1978. The report provides a discussion of the basis for both the current and revised inspection programs, describes these programs, and shows how the NRC inspection force will be trained and utilized. In addition, the report includes a discussion of the actions that will be taken to assure the objectivity of inspectors

The economic impact of revision otologic surgery.

Science.gov (United States)

Nadimi, Sahar; Leonetti, John P; Pontikis, George

2016-03-01

Revision otologic surgery places a significant economic burden on patients and the healthcare system. We conducted a retrospective chart analysis to estimate the economic impact of revision canal-wall-down (CWD) mastoidectomy. We reviewed the medical records of all 189 adults who had undergone CWD mastoidectomy performed by the senior author between June 2006 and August 2011 at Loyola University Medical Center in Maywood, Ill. Institutional charges and collections for all patients were extrapolated to estimate the overall healthcare cost of revision surgery in Illinois and at the national level. Of the 189 CWD mastoidectomies, 89 were primary and 100 were revision procedures. The total charge for the revision cases was $2,783,700, and the net reimbursement (collections) was $846,289 (30.4%). Using Illinois Hospital Association data, we estimated that reimbursement for 387 revision CWD mastoidectomies that had been performed in fiscal year 2011 was nearly $3.3 million. By extrapolating our data to the national level, we estimated that 9,214 patients underwent revision CWD mastoidectomy in the United States during 2011, which cost the national healthcare system roughly $76 million, not including lost wages and productivity. Known causes of failed CWD mastoidectomies that often result in revision surgery include an inadequate meatoplasty, a facial ridge that is too high, residual diseased air cells, and recurrent cholesteatoma. A better understanding of these factors can reduce the need for revision surgery, which could have a positive impact on the economic strain related to this procedure at the local, state, and national levels.

TMACS test procedure TP003: Graphics. Revision 5

International Nuclear Information System (INIS)

Scanlan, P.K.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the graphics requirements of the TMACS. The features to be tested are the data display graphics and the graphic elements that provide for operator control and selection of displays

TMACS test procedure TP003: Graphics. Revision 6

International Nuclear Information System (INIS)

Scanlan, P.K.; Washburn, S.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the graphics requirements of the TMACS. The features to be tested are the data display graphics and the graphic elements that provide for operator control and selection of displays

An internally validated prognostic model for success in revision stapes surgery for otosclerosis.

Science.gov (United States)

Wegner, Inge; Vincent, Robert; Derks, Laura S M; Rauh, Simone P; Heymans, Martijn W; Stegeman, Inge; Grolman, Wilko

2018-03-09

To develop a prediction model that can accurately predict the chance of success following revision stapes surgery in patients with recurrent or persistent otosclerosis at 2- to 6-months follow-up and to validate this model internally. A retrospective cohort study of prospectively gathered data in a tertiary referral center. The associations of 11 prognostic factors with treatment success were tested in 705 cases using multivariable logistic regression analysis with backward selection. Success was defined as a mean air-bone gap closure to 10 dB or less. The most relevant predictors were used to derive a clinical prediction rule to determine the probability of success. Internal validation by means of bootstrapping was performed. Model performance indices, including the Hosmer-Lemeshow test, the area under the receiver operating characteristics curve (AUC), and the explained variance were calculated. Success was achieved in 57.7% of cases at 2- to 6-months follow-up. Certain previous surgical techniques, primary causes of failure leading up to revision stapes surgery, and positions of the prosthesis placed during revision surgery were associated with higher success percentages. The clinical prediction rule performed moderately well in the original dataset (Hosmer-Lemeshow P = .78; AUC = 0.73; explained variance = 22%), which slightly decreased following internal validation by means of bootstrapping (AUC = 0.69; explained variance = 13%). Our study established the importance of previous surgical technique, primary cause of failure, and type of the prosthesis placed during the revision surgery in predicting the probability of success following stapes surgery at 2- to 6-months follow-up. 2b. Laryngoscope, 2018. © 2018 The American Laryngological, Rhinological and Otological Society, Inc.

Atypical performance patterns on Delis-Kaplan Executive Functioning System Color-Word Interference Test: Cognitive switching and learning ability in older adults.

Science.gov (United States)

Berg, Jody-Lynn; Swan, Natasha M; Banks, Sarah J; Miller, Justin B

2016-09-01

Cognitive set shifting requires flexible application of lower level processes. The Delis-Kaplan Executive Functioning System (DKEFS) Color-Word Interference Test (CWIT) is commonly used to clinically assess cognitive set shifting. An atypical pattern of performance has been observed on the CWIT; a subset of individuals perform faster, with equal or fewer errors, on the more difficult inhibition/switching than the inhibition trial. This study seeks to explore the cognitive underpinnings of this atypical pattern. It is hypothesized that atypical patterns on CWIT will be associated with better performance on underlying cognitive measures of attention, working memory, and learning when compared to typical CWIT patterns. Records from 239 clinical referrals (age: M = 68.09 years, SD = 10.62; education: M = 14.87 years, SD = 2.73) seen for a neuropsychological evaluation as part of diagnostic work up in an outpatient dementia and movement disorders clinic were sampled. The standard battery of tests included measures of attention, learning, fluency, executive functioning, and working memory. Analyses of variance (ANOVAs) were conducted to compare the cognitive performance of those with typical versus atypical CWIT patterns. An atypical pattern of performance was confirmed in 23% of our sample. Analyses revealed a significant group difference in acquisition of information on both nonverbal (Brief Visuospatial Memory Test-Revised, BVMT-R total recall), F(1, 213) = 16.61, p < .001, and verbal (Hopkins Verbal Learning Test-Revised, HVLT-R total recall) learning tasks, F(1, 181) = 6.43, p < .01, and semantic fluency (Animal Naming), F(1, 232) = 7.57, p = .006, with the atypical group performing better on each task. Effect sizes were larger for nonverbal (Cohen's d = 0.66) than verbal learning (Cohen's d = 0.47) and semantic fluency (Cohen's d = 0.43). Individuals demonstrating an atypical pattern of performance on the CWIT inhibition/switching trial also demonstrated relative

Textiles Performance Testing Facilities

Data.gov (United States)

Federal Laboratory Consortium — The Textiles Performance Testing Facilities has the capabilities to perform all physical wet and dry performance testing, and visual and instrumental color analysis...

TMACS Test Procedure TP008: SACS Interface. Revision 5

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure tests the TMACS SACS Interface functions

Operator performance in non-destructive testing: A study of operator performance in a performance test

Energy Technology Data Exchange (ETDEWEB)

Enkvist, J.; Edland, A.; Svenson, Ola [Stockholm Univ. (Sweden). Dept. of Psychology

2000-05-15

In the process industries there is a need of inspecting the integrity of critical components without disrupting the process. Such in-service inspections are typically performed with non-destructive testing (NDT). In NDT the task of the operator is to (based on diagnostic information) decide if the component can remain in service or not. The present study looks at the performance in NDT. The aim is to improve performance, in the long run, by exploring the operators' decision strategies and other underlying factors and to this way find out what makes some operators more successful than others. Sixteen operators performed manual ultrasonic inspections of four test pieces with the aim to detect (implanted) cracks. In addition to these performance demonstration tests (PDT), the operators performed independent ability tests and filled out questionnaires. The results show that operators who trust their gut feeling more than the procedure (when the two come to different results) and that at the same time have a positive attitude towards the procedure have a higher PDT performance. These results indicate the need for operators to be motivated and confident when performing NDT. It was also found that the operators who performed better rated more decision criteria higher in the detection phase than the operators who performed worse. For characterizing it was the other way around. Also, the operators who performed better used more time, both detecting and characterizing, than the operators who performed worse.

Operator performance in non-destructive testing: A study of operator performance in a performance test

International Nuclear Information System (INIS)

Enkvist, J.; Edland, A.; Svenson, Ola

2000-05-01

In the process industries there is a need of inspecting the integrity of critical components without disrupting the process. Such in-service inspections are typically performed with non-destructive testing (NDT). In NDT the task of the operator is to (based on diagnostic information) decide if the component can remain in service or not. The present study looks at the performance in NDT. The aim is to improve performance, in the long run, by exploring the operators' decision strategies and other underlying factors and to this way find out what makes some operators more successful than others. Sixteen operators performed manual ultrasonic inspections of four test pieces with the aim to detect (implanted) cracks. In addition to these performance demonstration tests (PDT), the operators performed independent ability tests and filled out questionnaires. The results show that operators who trust their gut feeling more than the procedure (when the two come to different results) and that at the same time have a positive attitude towards the procedure have a higher PDT performance. These results indicate the need for operators to be motivated and confident when performing NDT. It was also found that the operators who performed better rated more decision criteria higher in the detection phase than the operators who performed worse. For characterizing it was the other way around. Also, the operators who performed better used more time, both detecting and characterizing, than the operators who performed worse

Psychometric Evaluation of the Revised Michigan Diabetes Knowledge Test (V.2016) in Arabic: Translation and Validation

OpenAIRE

Alhaiti, Ali Hassan; Alotaibi, Alanod Raffa; Jones, Linda Katherine; DaCosta, Cliff; Lenon, George Binh

2016-01-01

Objective. To translate the revised Michigan Diabetes Knowledge Test into the Arabic language and examine its psychometric properties. Setting. Of the 139 participants recruited through King Fahad Medical City in Riyadh, Saudi Arabia, 34 agreed to the second-round sample for retesting purposes. Methods. The translation process followed the World Health Organization’s guidelines for the translation and adaptation of instruments. All translations were examined for their validity and reliability...

Test specification for decant pump and winch assembly. Revision 2

International Nuclear Information System (INIS)

Staehr, T.W.

1995-01-01

This specification provides the requirements for testing of the vertical turbine decant pump including the floating suction with load sensing winch control, instrumentation and the associated PLC/PC control system. All assembly necessary for testing including piping, temporary wiring, etc., shall be performed by the Seller. All referenced figures are at the back of this document. The testing consists of performance testing, winch testing and calibration, instrumentation verification testing and run-in testing of the pump. Testing shall be done in the presence and under the direction of the Buyer in accordance with this procedure

Fixation of Hydroxyapatite-Coated Revision Implants Is Improved by the Surgical Technique of Cracking the Sclerotic Bone Rim

Science.gov (United States)

Elmengaard, Brian; Bechtold, Joan E.; Chen, Xinqian; Søballe, Kjeld

2013-01-01

Revision joint replacement has poorer outcomes that have been associated with poorer mechanical fixation. We investigate a new bone-sparing surgical technique that locally cracks the sclerotic bone rim formed during aseptic loosening. We inserted 16 hydroxyapatite-coated implants bilaterally in the distal femur of eight dogs, using a controlled weight-bearing experimental model that replicates important features of a typical revision setting. At 8 weeks, a control revision procedure and a crack revision procedure were performed on contralateral implants. The crack procedure used a splined tool to perform a systematic local perforation of the sclerotic bone rim of the revision cavity. After 4 weeks, the hydroxyapatite-coated implants were evaluated for mechanical fixation by a push-out test and for tissue distribution by histomorphometry. The cracking revision procedure resulted in significantly improved mechanical fixation, significantly more bone ongrowth and bone volume in the gap, and reduced fibrous tissue compared to the control revision procedure. The study demonstrates that the sclerotic bone rim prevents bone ingrowth and promotes fixation by fibrous tissue. The effect of the cracking technique may be due to improved access to the vascular compartment of the bone. The cracking technique is a simple surgical method that potentially can improve the fixation of revision implants in sclerotic regions important for obtaining the fixation critical for overall implant stability. PMID:19148940

Evaluation of Basel III revision of quantitative standards for implementation of internal models for market risk

Directory of Open Access Journals (Sweden)

Meera Sharma

2012-12-01

Full Text Available This paper studies revisions under Basel III for market risk which allow conservative combination of short and long period Value-at-Risks (VaRs. This is the first study that examines this issue. The performance of the combination method is evaluated through regulatory back tests, unconditional and conditional coverage tests. The combination improves performance in regulatory back tests and tests of unconditional coverage. A common trend is the superior performance of long (1000/750 day in combination with short (190/125 days VaR methods. The combination does not enhance conditional coverage performance. This is the first study on this topic.

TMACS Test Procedure TP010: Integration summary. Revision 5

International Nuclear Information System (INIS)

Spurling, D.G.

1994-01-01

The TMACS Soft Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes

Current Epidemiology of Revision Total Knee Arthroplasty in the United States.

Science.gov (United States)

Delanois, Ronald E; Mistry, Jaydev B; Gwam, Chukwuweike U; Mohamed, Nequesha S; Choksi, Ujval S; Mont, Michael A

2017-09-01

Revision surgery for failed total knee arthroplasty (TKA) continues to pose a substantial burden for the United States healthcare system. The predominant etiology of TKA failure has changed over time and may vary between studies. This report aims to update the current literature on this topic by using a large national database. Specifically, we analyzed: (1) etiologies for revision TKA; (2) frequencies of revision TKA procedures; (3) various demographics including payer type and region; and (4) the length of stay (LOS) and total charges based on type of revision TKA procedure. The Healthcare Cost and Utilization Project (HCUP) National Inpatient Sample (NIS) database was used to identify all revision TKA procedures performed between 2009 and 2013. Clinical, economic, and demographic data were collected and analyzed for 337,597 procedures. Patients were stratified according to etiology of failure, age, sex, race, US census region, and primary payor class. The mean LOS and total charges were also calculated. Infection was the most common etiology for revision TKA (20.4%), closely followed by mechanical loosening (20.3%). The most common revision TKA procedure performed was all component revision (31.3%). Medicare was the primary payor for the greatest proportion of revisions (57.7%). The South census region performed the most revision TKAs (33.2%). The overall mean LOS was 4.5 days, with arthrotomy for removal of prosthesis without replacement procedures accounting for the longest stays (7.8 days). The mean total charge for revision TKAs was $75,028.07. Without appropriate measures in place, the burden of revision TKAs may become overwhelming and pose a strain on providers and institutions. Continued insight into the etiology and epidemiology of revision TKAs may be the principle step towards improving outcomes and mitigating the need for future revisions. Copyright © 2017 Elsevier Inc. All rights reserved.

Reliability and Validity of the Computerized Revised Token Test: Comparison of Reading and Listening Versions in Persons with and without Aphasia

Science.gov (United States)

McNeil, Malcolm R.; Pratt, Sheila R.; Szuminsky, Neil; Sung, Jee Eun; Fossett, Tepanta R. D.; Fassbinder, Wiltrud; Lim, Kyoung Yuel

2015-01-01

Purpose: This study assessed the reliability and validity of intermodality associations and differences in persons with aphasia (PWA) and healthy controls (HC) on a computerized listening and 3 reading versions of the Revised Token Test (RTT; McNeil & Prescott, 1978). Method: Thirty PWA and 30 HC completed the test versions, including a…

Building America Performance Analysis Procedures: Revision 1

Energy Technology Data Exchange (ETDEWEB)

None

2004-06-01

To measure progress toward multi-year research goals, cost and performance trade-offs are evaluated through a series of controlled field and laboratory experiments supported by energy analysis techniques using test data to calibrate simulation models.

The Addenbrooke's Cognitive Examination Revised (ACE-R): a brief cognitive test battery for dementia screening.

Science.gov (United States)

Mioshi, Eneida; Dawson, Kate; Mitchell, Joanna; Arnold, Robert; Hodges, John R

2006-11-01

There is a clear need for brief, but sensitive and specific, cognitive screening instruments as evidenced by the popularity of the Addenbrooke's Cognitive Examination (ACE). We aimed to validate an improved revision (the ACE-R) which incorporates five sub-domain scores (orientation/attention, memory, verbal fluency, language and visuo-spatial). Standard tests for evaluating dementia screening tests were applied. A total of 241 subjects participated in this study (Alzheimer's disease=67, frontotemporal dementia=55, dementia of Lewy Bodies=20; mild cognitive impairment-MCI=36; controls=63). Reliability of the ACE-R was very good (alpha coefficient=0.8). Correlation with the Clinical Dementia Scale was significant (r=-0.321, pcognitive dysfunction. Copyright (c) 2006 John Wiley & Sons, Ltd.

Do screencasts help to revise prerequisite mathematics? An investigation of student performance and perception

Science.gov (United States)

Loch, Birgit; Jordan, Camilla R.; Lowe, Tim W.; Mestel, Ben D.

2014-02-01

Basic calculus skills that are prerequisites for advanced mathematical studies continue to be a problem for a significant proportion of higher education students. While there are many types of revision material that could be offered to students, in this paper we investigate whether short, narrated video recordings of mathematical explanations (screencasts) are a useful tool to enhance student learning when revisiting prerequisite topics. We report on the outcomes of a study that was designed to both measure change in student performance before and after watching screencasts, and to capture students' perception of the usefulness of screencasts in their learning. Volunteers were recruited from students enrolled on an entry module for the Mathematics Master of Science programme at the Open University to watch two screencasts sandwiched between two online calculus quizzes. A statistical analysis of student responses to the quizzes shows that screencasts can have a positive effect on student performance. Further analysis of student feedback shows that student confidence was increased by watching the screencasts. Student views on the value of screencasts for their learning indicated that they appreciated being able to watch a problem being solved and explained by an experienced mathematician; hear the motivation for a particular problem-solving approach; engage more readily with the material being presented, thereby retaining it more easily. The positive student views and impact on student scores indicate that short screencasts could play a useful role in revising prerequisite mathematics.

TMACS test procedure TP009: Acromag driver. Revision 5

International Nuclear Information System (INIS)

Bass, R.B.; Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the testing of the functionality of the TMACS Acromag driver software in conjunction with a new bridge for the Panalarm Annunciator system

Closing the feedback loop: engaging students in large first-year mathematics test revision sessions using pen-enabled screens

Science.gov (United States)

Donovan, Diane; Loch, Birgit

2013-01-01

How can active learning, peer learning and prompt feedback be achieved in large first-year mathematics classes? Further, what technologies may support these aims? In this article, we assert that test revision sessions in first-year mathematics held in a technology-enhanced lecture theatre can be highly interactive with students solving problems, learning from each other and receiving immediate feedback. This is facilitated by pen-enabled screens and synchronization software. We argue that the educational benefits achievable through the technology do outweigh the technological distractions, and that these benefits can be achieved by focused, targeted one-off sessions and not only by a semester-long, regular approach. Repeat mid-semester test revision sessions were offered on a non-compulsory basis using pen-enabled screens for all students. Students worked practice test questions and marked solutions to mathematical problems on the screens. Students' work was then displayed anonymously for their peers to see. Answers were discussed with the whole class. We discuss outcomes from two offerings of these sessions using student feedback and lecturer reflections and show the impact of participation on self-reported student confidence. Pedagogical approaches that the technology allowed for the first time in a large class are highlighted. Students responded uniformly positively.

RCBI-II: The Second Revision of the Revised Cyber Bullying Inventory

Science.gov (United States)

Topcu, Çigdem; Erdur-Baker, Özgür

2018-01-01

The aim of this study is to update the Turkish version of the Revised Cyber Bullying Inventory (RCBI) and eliminate specific technology names. Validity and reliability tests were carried out with 1,803 high school students. The updated version of the RCBI yields valid and reliable scores measuring cyberbullying and victimization.

The Effects of Bloom’s Revised Taxonomy on Measurement and Evaluation in Education

Directory of Open Access Journals (Sweden)

İrfan Yurdabakan

2012-12-01

Full Text Available The aim of this study is to discuss the revision of the original version of Bloom’s taxonomy of educational objectives under the leadership of Krathwohl and Anderson and its reflections on testing and assessment in education. Fort his purpose, international database was scanned to analyze the publications on “Bloom’s revised taxonomy and relationships between the revised taxonomy and testing and assessment”. The reasons for revision, the results that emerged following the revision and the reflections of those results on measurement and evaluation in education are described within the scope of those publications obtained

TMACS test procedure TP010: Integration summary. Revision 6

International Nuclear Information System (INIS)

Spurling, D.G.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure verifies that Test Procedures 1, 2, 3, 5 and 9 (WHC-SD-WM-TRP-105, 106, 107, 109 and 113) of TMACS Software Release 4.1 have been successfully completed

The Addenbrooke's Cognitive Examination Revised as a potential screening test for elderly drivers.

Science.gov (United States)

Ferreira, Inês S; Simões, Mário R; Marôco, João

2012-11-01

Considerable research has shown that neuropsychological tests are predictive of real-world driving ability. The Mini-Mental State Examination (MMSE) is a brief cognitive test that has been commonly used in the assessment of older drivers. However, this test has inherent problems that limit its validity to evaluate cognitive abilities related to driving and to screen for driving impairments in non-demented people. Therefore, it is useful to test new screening instruments that may predict potential unsafe drivers who require an in-depth neuropsychological assessment in a specialised centre. To date, the utility of the Addenbrooke's Cognitive Examination Revised (ACE-R) as an indicator of driving ability has not been established. In the current study, fifty older drivers (mean age=73.1 years) who were referred for a psychological assessment, the protocol of which included the ACE-R, underwent an on-road driving test. Using linear discriminant analyses, the results highlighted the higher classification accuracy of the ACE-R compared to the MMSE score, particularly for detecting unsafe drivers. Measures of visuospatial and executive functions, which are not incorporated in the MMSE score, had an incremental value in the prediction of driving ability. This emerging brief cognitive test may warrant additional study for use in the fitness to drive assessment of older adults. Copyright © 2012 Elsevier Ltd. All rights reserved.

A study on scar revision

Directory of Open Access Journals (Sweden)

Ashutosh Talwar

2016-04-01

Full Text Available Introduction: Scars are psychologically distressing for the patients and have an impact on the quality of life and self esteem of the patients. Scar revision is an aesthetic skill which is mastered by plastic surgeons and encroached now by dermatosurgeons. Scars on the face are aesthetically unacceptable and various techniques have been improvised for making a scar aesthetically acceptable. Various types of techniques are used for scar revision like W plasty, Z plasty and VY plasty. Aims: To see the efficacy of various scar revision techniques including Z plasty, VY plasty and W plasty in 30 patients with disfiguring scars. Methods: We selected twenty patients of disfiguring scars for the study. The scars from various causes including trauma and burns were included in our study. Various techniques of scar revision include Z plasty, W plasty and VY plasty were performed according to the type and site of scar. Results: Male: female was 1.5: 1. The scar revision surgery yielded excellent results with minimal complications including haematoma formation, secondary infection and delayed healing seen in 5% patients each. Regarding the efficacy of scar revision, excellent improvement was seen in 60% patients, moderate improvement was seen in 30% patients and mild improvement was seen in 10% patients. Conclusions: Dermatologists can employ a number of surgical scar revision techniques. While some are better suited to treat specific types of scars, they can be used in combination with each other or with adjunctive therapies to achieve optimal results.

Containment Emergency Sump Performance. Technical findings related to Unresolved Safety Issue A-43. Revision 1

International Nuclear Information System (INIS)

1985-10-01

This report summarizes key technical findings related to Unresolved Safety Issue (USI) A-43, Containment Emergency Sump Performance. Both BWRs and PWRs are considered in this report. Emergency core cooling systems require a clean, reliable water source to maintain long-term recirculation following a loss-of-coolant accident (LOCA). PWRs rely on the containment emergency sump to provide such a water supply to residual heat removal pumps and containment spray pumps. BWRs rely on pump suction intakes in the suppression pool or wet well to provide water to residual heat removal and core spray systems. Thus, the technical findings in this report provide information on post-LOCA recirculation. These findings have been derived from extensive experimental studies, generic plant studies, and assessments of sumps used for long-term cooling. Results of hydraulic tests have shown that the potential for air ingestion is less severe than previously hypothesized. The effects of debris blockage on NPSH margin must be dealt with on a plant-specific basis. These findings have been used to develop revisions to Regulatory Guide 1.82 and Standard Review Plan Section 6.2.2 (NUREG-0800)

Underground Test Area Activity Quality Assurance Plan Nevada National Security Site, Nevada. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Farnham, Irene [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States); Krenzien, Susan [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

2012-10-01

This Quality Assurance Plan (QAP) provides the overall quality assurance (QA) requirements and general quality practices to be applied to the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Underground Test Area (UGTA) activities. The requirements in this QAP are consistent with DOE Order 414.1C, Quality Assurance (DOE, 2005); U.S. Environmental Protection Agency (EPA) Guidance for Quality Assurance Project Plans for Modeling (EPA, 2002); and EPA Guidance on the Development, Evaluation, and Application of Environmental Models (EPA, 2009). NNSA/NSO, or designee, must review this QAP every two years. Changes that do not affect the overall scope or requirements will not require an immediate QAP revision but will be incorporated into the next revision cycle after identification. Section 1.0 describes UGTA objectives, participant responsibilities, and administrative and management quality requirements (i.e., training, records, procurement). Section 1.0 also details data management and computer software requirements. Section 2.0 establishes the requirements to ensure newly collected data are valid, existing data uses are appropriate, and environmental-modeling methods are reliable. Section 3.0 provides feedback loops through assessments and reports to management. Section 4.0 provides the framework for corrective actions. Section 5.0 provides references for this document.

Revision of infected knee arthroplasties in Denmark

DEFF Research Database (Denmark)

Lindberg-Larsen, Martin; Jørgensen, Christoffer C; Bagger, Jens

2016-01-01

Background and purpose - The surgical treatment of periprosthetic knee infection is generally either a partial revision procedure (open debridement and exchange of the tibial insert) or a 2-stage exchange arthroplasty procedure. We describe the failure rates of these procedures on a nationwide...... basis. Patients and methods - 105 partial revisions (100 patients) and 215 potential 2-stage revision procedures (205 patients) performed due to infection from July 1, 2011 to June 30, 2013 were identified from the Danish Knee Arthroplasty Register (DKR). Failure was defined as surgically related death...

Revised Bethesda Guidelines for Hereditary Nonpolyposis Colorectal Cancer (Lynch Syndrome) and Microsatellite Instability

Science.gov (United States)

Umar, Asad; Boland, C. Richard; Terdiman, Jonathan P.; Syngal, Sapna; de la Chapelle, Albert; Rüschoff, Josef; Fishel, Richard; Lindor, Noralane M.; Burgart, Lawrence J.; Hamelin, Richard; Hamilton, Stanley R.; Hiatt, Robert A.; Jass, Jeremy; Lindblom, Annika; Lynch, Henry T.; Peltomaki, Païvi; Ramsey, Scott D.; Rodriguez-Bigas, Miguel A.; Vasen, Hans F. A.; Hawk, Ernest T.; Barrett, J. Carl; Freedman, Andrew N.; Srivastava, Sudhir

2010-01-01

Hereditary nonpolyposis colorectal cancer (HNPCC), also known as Lynch syndrome, is a common autosomal dominant syndrome characterized by early age at onset, neoplastic lesions, and microsatellite instability (MSI). Because cancers with MSI account for approximately 15% of all colorectal cancers and because of the need for a better understanding of the clinical and histologic manifestations of HNPCC, the National Cancer Institute hosted an international workshop on HNPCC in 1996, which led to the development of the Bethesda Guidelines for the identification of individuals with HNPCC who should be tested for MSI. To consider revision and improvement of the Bethesda Guidelines, another HNPCC workshop was held at the National Cancer Institute in Bethesda, MD, in 2002. In this commentary, we summarize the Workshop presentations on HNPCC and MSI testing; present the issues relating to the performance, sensitivity, and specificity of the Bethesda Guidelines; outline the revised Bethesda Guidelines for identifying individuals at risk for HNPCC; and recommend criteria for MSI testing. PMID:14970275

Bulletin 2005-12 : revised Alberta pipeline regulation issued

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-05-31

A revised Pipeline Regulation has been issued and is currently available on the Alberta Energy and Utilities Board (EUB) website. Changes to the regulation reflect bothchanges in EUB regulatory policy and processes and technological improvements. Goals of the revision include improvements in overall pipeline performance, and the implementation of recommendations derived from the Public Safety and Sour Gas Committee concerning sour gas pipeline safety. The regulation was re-organized for greater clarity, and structured into 11 parts. Issues concerning the transition to the revised regulation were presented. The summary of notable administrative changes included clarifications of when a pipeline application is not required; when ABSA approval is required for steam lines; situations for which low-pressure natural gas lines must be licensed; and emergency response requirements. Technical clarifications include requirements for pipeline operations and maintenance manuals; composite materials; limitations on amounts of H{sub 2}S in polymeric pipe; pressure mismatches; approval for testing with gaseous media; venting of small volumes of raw gas; right-of-way surveillance; inspection of surface construction activities; annual corrosion evaluations; registering of pipelines and excavators in controlled areas with Alberta One-Call; ground disturbance training; restoration and signage maintenance on abandoned pipelines; sour service steel pipelines; unused pipelines and abandoned pipelines; and remediation of stub ends in operating pipelines.

Revising Translations

DEFF Research Database (Denmark)

Rasmussen, Kirsten Wølch; Schjoldager, Anne

2011-01-01

The paper explains the theoretical background and findings of an empirical study of revision policies, using Denmark as a case in point. After an overview of important definitions, types and parameters, the paper explains the methods and data gathered from a questionnaire survey and an interview...... survey. Results clearly show that most translation companies regard both unilingual and comparative revisions as essential components of professional quality assurance. Data indicate that revision is rarely fully comparative, as the preferred procedure seems to be a unilingual revision followed by a more...... or less comparative rereading. Though questionnaire data seem to indicate that translation companies use linguistic correctness and presentation as the only revision parameters, interview data reveal that textual and communicative aspects are also considered. Generally speaking, revision is not carried...

Revised Reading the Mind in the Eyes Test (RMET - Brazilian version

Directory of Open Access Journals (Sweden)

Breno Sanvicente-Vieira

2014-03-01

Full Text Available Objective: To translate and adapt to Brazilian Portuguese the Revised Reading the Mind in the Eyes Test (RMET, in both paper-and-pencil and computerized versions. The RMET is a well-accepted instrument for assessment of Theory of Mind (ToM, an important component of social cognition. Methods: Following a guideline for translation of material for clinical populations, this study had three main phases: 1 formal translation and semantic adaptation to Brazilian Portuguese; 2 an acceptability trial with health professionals as judges evaluating picture-word matching; and 3 a trial using the paper-and-pencil and computerized versions (experiments built in E-Prime 2.0.10 software with healthy participants to test whether the instrument has similar outputs to those expected in versions in other languages. Results: RMET was adequately adapted to Brazilian Portuguese. This version showed acceptability and outputs similar to versions of the instrument in other languages, including the original one. We kept the same number of images as the original English version. Conclusions: Considering the scarcity of cognitive assessment instruments adequately adapted to Portuguese and the importance of social cognition in many psychiatric disorders, this work adds an important resource to Brazilian research and is administrable in both paper-and-pencil and computerized versions.

TMACS test procedure TP001: Alarm management. Revision 6

International Nuclear Information System (INIS)

Scanlan, P.K.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the Alarm Management requirements of the TMACS. The features to be tested are: real-time alarming on high and low level and discrete alarms, equipment alarms, dead-band filtering, alarm display color coding, alarm acknowledgement, and alarm logging

NEEDLE REVISION WITH MITOMYCIN-C IN ENCAPSULATED BLEBS

Directory of Open Access Journals (Sweden)

R Zarei

2008-08-01

Full Text Available "nThe most common cause of failure during the first trimester after trabeculectomy is encapsulated bleb and needling bleb revision is a less invasive method in the management of refractory cases. The purpose of this study is to determine the efficacy and safety of mitomycin-C (MMC augmented bleb revision of failed filtration surgery. This study is a before-after (paired observation. 33 patients with failed trabeculectomy because of bleb encapsulation, whose intraocular pressure (IOP was not reduced under 21 mmHg despite of medications and digital massage , underwent needling bleb revision and subconjunctival injection of 0.1 ml MMC (0.4 mg/ml.The mean follow-up time was 9.24 ± 5.27 months (1-20 months. Statistical analysis of the data included the paired two-tailed Student's t test for preoperative and postoperative IOP and number of medications. 36 needling procedures (mean, 1.09 ± 0.21 revisions per eye were performed on 33 eyes. Patients were between 10-80 years old (mean, 45.67 ± 22.41 years and mean follow-up was 9.24 ± 5.27 months. IOP decreased from 29.06 ± 5.03 mmHg to 18.21 ± 6.76 mmHg at last follow-up (P= 0.000. Antiglaucoma medications decreased from 2.18 ± 0.58 to 1.36 ± 0.29 at last follow-up (P= 0.000.Overall, 6 (18.2% of 33 cases achieved a complete success and 20 (60.6% of cases achieved a qualified success. The complications of this procedure were subconjunctival hemorrhage (17 cases, hyphema (5 cases and conjunctival button hole (2 cases. Needling bleb revision with mitomycin-C appears to be an effective and relatively safe way to revive failed filtration surgery.

Ventriculoperitoneal shunt complications needing shunt revision in children: A review of 5 years of experience with 48 revisions

Directory of Open Access Journals (Sweden)

Rajendra K Ghritlaharey

2012-01-01

Full Text Available Background: The aim of this study was to review the management of ventriculoperitoneal (VP shunt complications in children. Patients and Methods: During the last 5 years (January 1, 2006 to December 31, 2010, 236 VP shunt operations were performed in children under 12 years of age; of these, 40 (16.94% developed shunt complications and those who underwent VP shunt revisions were studied. Results: This prospective study included 40 (28 boys and 12 girls children and required 48 shunt revisions. Complications following VP shunts that required shunt revisions were peritoneal catheter/peritoneal end malfunction (18, shunt/shunt tract infections (7, extrusion of peritoneal catheter through anus (5, ventricular catheter malfunction (4, cerebrospinal fluid (CSF leak from abdominal wound (4, shunt system failure (2, ventricular end/shunt displacement (2, CSF pseudocysts peritoneal cavity (2, extrusion of peritoneal catheter from neck, chest, abdominal scar and through umbilicus, one each. Four-fifth of these shunt complications occurred within 6 months of previous surgery. Surgical procedures done during shunt revisions in order of frequency were revision of peritoneal part of shunt (27, 56.25%, revision of entire shunt system (6, 12.5%, extra ventricular drainage and delayed re-shunt (5, 10.41%, shunt removal and delayed re-shunt (5, 10.41%, opposite side shunting (2, 4.16%, cysts excision and revision of peritoneal catheter (2, 4.16% and revision of ventricular catheter (1, 2.08%. The mortalities following VP shunt operations were 44 (18.64% and following shunt revisions were 4 (10%. Conclusions: VP shunt done for hydrocephalus in children is not only prone for complications and need for revision surgery but also associated with considerable mortality.

Pump testing - Comparison of factory vs. field test of centrifugal pumps

International Nuclear Information System (INIS)

Fehlau, R.

1992-01-01

Testing of pumps in situ, i.e., as installed in a system, will typically yield somewhat different performance results from the original manufacturer's factory test. This paper discusses some of the reasons for these variations. It shows that the factory test curves can be used for evaluation of initial acceptance tests but not for reference in normal inservice testing (IST). This is the basis for reference values used in American Society of Mechanical Engineers (ASME) Section 11 specifications and the revised ASME Code 1990

Revised associative inference paradigm confirms relational memory impairment in schizophrenia.

Science.gov (United States)

Armstrong, Kristan; Williams, Lisa E; Heckers, Stephan

2012-07-01

Patients with schizophrenia have widespread cognitive impairments, with selective deficits in relational memory. We previously reported a differential relational memory deficit in schizophrenia using the Associative Inference Paradigm (AIP), a task suggested by the Cognitive Neuroscience Treatment Research to Improve Cognition in Schizophrenia (CNTRICS) initiative to examine relational memory. However, the AIP had limited feasibility for testing in schizophrenia because of high attrition of schizophrenia patients during training. Here we developed and tested a revised version of the AIP to improve feasibility. 30 healthy control and 37 schizophrenia subjects received 3 study-test sessions on 3 sets of paired associates: H-F1 (house paired with face), H-F2 (same house paired with new face), and F3-F4 (two novel faces). After training, subjects were tested on the trained, noninferential Face-Face pairs (F3-F4) and novel, inferential Face-Face pairs (F1-F2), constructed from the faces of the trained House-Face pairs. Schizophrenia patients were significantly more impaired on the inferential F1-F2 pairs than the noninferential F3-F4 pairs, providing evidence for a differential relational memory deficit. Only 8% of schizophrenia patients were excluded from testing because of poor training performance. The revised AIP confirmed the previous finding of a relational memory deficit in a larger and more representative sample of schizophrenia patients.

A revised Thai Multi-Dimensional Scale of Perceived Social Support.

Science.gov (United States)

Wongpakaran, Nahathai; Wongpakaran, Tinakon

2012-11-01

In order to ensure the construct validity of the three-factor model of the Multi-dimensional Scale of Perceived Social Support (MSPSS), and based on the assumption that it helps users differentiate between sources of social support, in this study a revised version was created and tested. The aim was to compare the level of model fit of the original version of the MSPSS against the revised version--which contains a minor change from the original. The study was conducted on 486 medical students who completed the original and revised versions of the MSPSS, as well as the Rosenberg Self-Esteem Scale (Rosenberg, 1965) and Beck Depression Inventory II (Beck, Steer, & Brown, 1996). Confirmatory factor analysis was performed to compare the results, showing that the revised version of MSPSS demonstrated a good internal consistency--with a Cronbach's alpha of .92 for the MSPSS questionnaire, and a significant correlation with the other scales, as predicted. The revised version provided better internal consistency, increasing the Cronbach's alpha for the Significant Others sub-scale from 0.86 to 0.92. Confirmatory factor analysis revealed an acceptable model fit: chi2 128.11, df 51, p < .001; TLI 0.94; CFI 0.95; GFI 0.90; PNFI 0.71; AGFI 0.85; RMSEA 0.093 (0.073-0.113) and SRMR 0.042, which is better than the original version. The tendency of the new version was to display a better level of fit with a larger sample size. The limitations of the study are discussed, as well as recommendations for further study.

Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems

Energy Technology Data Exchange (ETDEWEB)

Conover, David R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crawford, Aladsair J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fuller, Jason C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gourisetti, Sri Nikhil Gup [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Viswanathan, Vilayanur V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ferreira, Summer [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schoenwald, David [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rosewater, David [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-04-01

The Protocol for Uniformly Measuring and Expressing the Performance of Energy Storage Systems (PNNL-22010) was first issued in November 2012 as a first step toward providing a foundational basis for developing an initial standard for the uniform measurement and expression of energy storage system (ESS) performance. Based on experiences with the application and use of that document, and to include additional ESS applications and associated duty cycles, test procedures and performance metrics, a first revision of the November 2012 Protocol was issued in June 2014 (PNNL 22010 Rev. 1). As an update of the 2014 revision 1 to the Protocol, this document (the March 2016 revision 2 to the Protocol) is intended to supersede the June 2014 revision 1 to the Protocol and provide a more user-friendly yet more robust and comprehensive basis for measuring and expressing ESS performance.

The performance testing

International Nuclear Information System (INIS)

Mayr, A.

1975-01-01

Concerning the time-schedule of reactor performance tests they normally begin when suppliers or constructors have finished construction and made all necessary construction and coordinated tests. If the last-mentioned tests are conducted profoundly, they contribute substantially to a quick and simple carrying-out of the last performance tests and to the general quality of components and systems. At this stage all components of a system should be properly fixed, machinery, instruments and electrical components adjusted and calibrated, all set-points tested, electrical and other supply units in operation or ready to operate and all functions pretested. Just at this stage of the work most of the existing defects and failures of systems can be found. Remembering the fact that the difficulty of operation of complex systems results from detail problems, it is extremely useful to remove all things of this kind as soon as possible, at the latest at this time where it is done easily and normally quickly without influencing start-up-procedures of other systems or even of the total plant. (orig./TK) [de

Usability Results from Human Performance Feedback and Development (HPFD) and ePerformance System Users: Technical Report #1

National Research Council Canada - National Science Library

Dean, Elizabeth; Aspinwall, Kimberly R; Schwerin, Michael J; Kendrick, Douglas E

2006-01-01

...) and ePerformance system. This second and final iteration of usability testing was designed to verify the functionality of system revisions made as a result of recommendations offered in Schwerin et al. (2004...

The association between metal allergy, total knee arthroplasty, and revision

DEFF Research Database (Denmark)

Münch, Henrik J; Jakobsen, Stig Storgaard; Olesen, Jens T

2015-01-01

BACKGROUND AND PURPOSE: It is unclear whether delayed-type hypersensitivity reactions against implanted metals play a role in the etiopathogenesis of malfunctioning total knee arthroplasties. We therefore evaluated the association between metal allergy, defined as a positive patch test reaction...... to common metal allergens, and revision surgery in patients who underwent knee arthroplasty. PATIENTS AND METHODS: The nationwide Danish Knee Arthroplasty Register, including all knee-implanted patients and revisions in Denmark after 1997 (n = 46,407), was crosslinked with a contact allergy patch test......, the prevalence of cobalt and chromium allergy was markedly higher. Metal allergy that was diagnosed before implant surgery appeared not to increase the risk of implant failure and revision surgery. INTERPRETATION: While we could not confirm that a positive patch test reaction to common metals is associated...

Underground Test Area Activity Quality Assurance Plan Nevada National Security Site, Nevada. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Krenzien, Susan [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States); Farnham, Irene [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

2015-06-01

This Quality Assurance Plan (QAP) provides the overall quality assurance (QA) requirements and general quality practices to be applied to the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) Underground Test Area (UGTA) activities. The requirements in this QAP are consistent with DOE Order 414.1D, Change 1, Quality Assurance (DOE, 2013a); U.S. Environmental Protection Agency (EPA) Guidance for Quality Assurance Project Plans for Modeling (EPA, 2002); and EPA Guidance on the Development, Evaluation, and Application of Environmental Models (EPA, 2009). If a participant’s requirement document differs from this QAP, the stricter requirement will take precedence. NNSA/NFO, or designee, must review this QAP every two years. Changes that do not affect the overall scope or requirements will not require an immediate QAP revision but will be incorporated into the next revision cycle after identification. Section 1.0 describes UGTA objectives, participant responsibilities, and administrative and management quality requirements (i.e., training, records, procurement). Section 1.0 also details data management and computer software requirements. Section 2.0 establishes the requirements to ensure newly collected data are valid, existing data uses are appropriate, and environmental-modeling methods are reliable. Section 3.0 provides feedback loops through assessments and reports to management. Section 4.0 provides the framework for corrective actions. Section 5.0 provides references for this document.

Revised results for geomechanical testing of MRIG-9 core for the potential SPR siting at the Richton Salt Dome.

Energy Technology Data Exchange (ETDEWEB)

Broome, Scott Thomas; Bauer, Stephen J.

2010-02-01

This report is a revision of SAND2009-0852. SAND2009-0852 was revised because it was discovered that a gage used in the original testing was mis-calibrated. Following the recalibration, all affected raw data were recalculated and re-presented. Most revised data is similar to, but slightly different than, the original data. Following the data re-analysis, none of the inferences or conclusions about the data or site relative to the SAND2009-0852 data have been changed. A laboratory testing program was developed to examine the mechanical behavior of salt from the Richton salt dome. The resulting information is intended for use in design and evaluation of a proposed Strategic Petroleum Reserve storage facility in that dome. Core obtained from the drill hole MRIG-9 was obtained from the Texas Bureau of Economic Geology. Mechanical properties testing included: (1) acoustic velocity wave measurements; (2) indirect tensile strength tests; (3) unconfined compressive strength tests; (4) ambient temperature quasi-static triaxial compression tests to evaluate dilational stress states at confining pressures of 725, 1450, 2175, and 2900 psi; and (5) confined triaxial creep experiments to evaluate the time-dependent behavior of the salt at axial stress differences of 4000 psi, 3500 psi, 3000 psi, 2175 psi and 2000 psi at 55 C and 4000 psi at 35 C, all at a constant confining pressure of 4000 psi. All comments, inferences, discussions of the Richton characterization and analysis are caveated by the small number of tests. Additional core and testing from a deeper well located at the proposed site is planned. The Richton rock salt is generally inhomogeneous as expressed by the density and velocity measurements with depth. In fact, we treated the salt as two populations, one clean and relatively pure (> 98% halite), the other salt with abundant (at times) anhydrite. The density has been related to the insoluble content. The limited mechanical testing completed has allowed us to

40 CFR 60.8 - Performance tests.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Performance tests. 60.8 Section 60.8... PERFORMANCE FOR NEW STATIONARY SOURCES General Provisions § 60.8 Performance tests. (a) Except as specified in... conduct performance test(s) and furnish the Administrator a written report of the results of such...

Performance specifications for health physics instrumentation: portable instrumentation for use in normal work environments. Part 2. Test results

International Nuclear Information System (INIS)

Kenoyer, J.L.; Swinth, K.L.; Stoetzel, G.A.; Selby, J.M.

1986-09-01

The Pacific Northwest Laboratory evaluated a draft American National Standards Institute Standard N42.17 (ANSI N42.17) on performance specifications for health physics instrumentation through a project jointly funded by the US Department of Energy and the US Nuclear Regulatory Commission. The evaluation involved testing a representative cross section of instruments against criteria in the standard. This report presents results of the testing program. A brief history of the project is included in the introduction. The instrumentation tested is described in general terms (i.e., types, ranges); however, no direct relationship between the results and a specific instrument model is made in this report. Testing requirements in ANSI N42.17D4, Revision 1 (May 1985) are summarized and the methods by which the tests are performed are discussed. Brief descriptions of the testing equipment are included in the methods section of the report. More detailed information about the draft standard, testing requirements and procedures, and the test equipment is included in ''Performance Specifications for Health Physics Instrumentation - Portable Instrumentation for Use in Normal Work Environments, Part 1: Manual of Testing Procedures.'' Results of testing are given in two formats: test-by-test and instrument-by-instrument. Discussion is included on significant and interesting findings, on comparisons of results from the same type of instruments from same and different manufacturers, and on data grouped by manufacturer. Conclusions are made on the applicability and practicality of the proposed standard and on instrument performance. Changes that have been made to the proposed standard based on findings of the testing program are listed and discussed. 22 refs., 11 figs., 77 tabs

Recurrent instability after revision anterior shoulder stabilization surgery.

Science.gov (United States)

Friedman, Lisa Genevra Mandeville; Griesser, Michael J; Miniaci, Anthony A; Jones, Morgan H

2014-03-01

The purpose of this study was to perform a systematic review of the literature to compare outcomes of revision anterior stabilization surgeries based on technique. This study also sought to compare the impact of bone defects on outcomes. A systematic review of the electronic databases PubMed, Cochrane Central Register of Controlled Trials, and Scopus was performed in July 2012 and March 2013. Of 345 articles identified in the search, 17 studies with Level I to IV Evidence satisfied the inclusion criteria and were analyzed according to PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines. Recurrent instability was defined as redislocation, resubluxation, or a positive apprehensive test after revision surgery. Procedures were categorized as arthroscopic Bankart repair, open Bankart repair, Bristow-Latarjet procedure, and other open procedures. In total, 388 shoulders were studied. Male patients comprised 74.1% of patients, 66.7% of cases involved the dominant shoulder, the mean age was 28.2 years, and the mean follow-up period was 44.2 months. The surgical procedures classified as "other open procedures" had the highest rate of recurrent instability (42.7%), followed by arthroscopic Bankart repair (14.7%), the Bristow-Latarjet procedure (14.3%), and open Bankart repair (5.5%). Inconsistent reporting of bone defects precluded drawing significant conclusions. A number of different procedures are used to address recurrent instability after a primary operation for anterior shoulder instability has failed. There is significant variability in the rate of recurrent instability after revision anterior shoulder stabilization surgery. Level IV, systematic review of Level I to IV studies. Copyright © 2014 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

HEDR modeling approach: Revision 1

International Nuclear Information System (INIS)

Shipler, D.B.; Napier, B.A.

1994-05-01

This report is a revision of the previous Hanford Environmental Dose Reconstruction (HEDR) Project modeling approach report. This revised report describes the methods used in performing scoping studies and estimating final radiation doses to real and representative individuals who lived in the vicinity of the Hanford Site. The scoping studies and dose estimates pertain to various environmental pathways during various periods of time. The original report discussed the concepts under consideration in 1991. The methods for estimating dose have been refined as understanding of existing data, the scope of pathways, and the magnitudes of dose estimates were evaluated through scoping studies

Engineering work plan for container venting system drill press assembly troubleshooting. Revision 1

International Nuclear Information System (INIS)

Prather, M.C.

1994-11-01

This work plan is for troubleshooting the current CVS drill press to ensure that the drill bit assembly doesn't bind in the press plate. A drill press assembly has been fabricated for the Container Venting System (CVS). The drill bit assembly has bound in the press plate in previous revisions of this design. Initial troubleshooting of the drill press per Rev. 0 of this work plan was performed at the 200W Kaiser Machine Shop under Work Package 2H9401670F, Internal Work Order E20027. The drill press operated without jamming. Then, during the pre-operational test on 11/14/17 and the operational test on 11/17/94, two drum lids were drilled. Immediately after the test on 11/17/94, the drill was again operated, and it jammed. An inspection found shavings at the bottom of the drill bit assembly, between the drill bit sleeve and the press plate bore. This revised work plan provides direction for the machine shop to diagnose and correct this recent problem

Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version 2

International Nuclear Information System (INIS)

Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

2002-10-01

Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institut, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make specification documents for the fuel pellet, the sphere-pac fuel particles, the vipac fuel fragments, and the fuel segment fabrication. JNC should make the fabrication drawings for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Holland). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Holland). The fabrication drawings have been made under the design assignment with PSI, and consist of the drawings of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications was discussed and agreed among all partners. According to this agreement, the fabrication drawings were revised in January 2002. After the earlier revision, the shape of particle retainer to be made by PSI was modified from its drawing beforehand delivered. In this report, the fabrication drawings revised again will be shown, and the fabrication procedure (welding Qualification Tests) will be modified in accordance with the result of discussion on the 3rd technical meeting held in September 2002. These design works have been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center under the commission of Plutonium Fuel

Revision Total Hip Arthoplasty: Factors Associated with Re-Revision Surgery

OpenAIRE

Khatod, M; Cafri, G; Inacio, MCS; Schepps, AL; Paxton, EW; Bini, SA

2015-01-01

The survivorship of implants after revision total hip arthroplasty and risk factors associated with re-revision are not well defined. We evaluated the re-revision rate with use of the institutional total joint replacement registry. The purpose of this study was to determine patient, implant, and surgeon factors associated with re-revision total hip arthroplasty.A retrospective cohort study was conducted. The total joint replacement registry was used to identify patients who had undergone revi...

Clinical and Economic Burden of Revision Knee Arthroplasty

Directory of Open Access Journals (Sweden)

Mohit Bhandari

2012-01-01

Full Text Available Surgery is indicated for symptomatic knee osteoarthritis (OA when conservative measures are unsuccessful. High tibial osteotomy (HTO, unicompartmental knee arthroplasty (UKA, and total knee arthroplasty (TKA are surgical options intended to relieve knee OA pain and dysfunction. The choice of surgical intervention is dependent on several factors such as disease location, patient age, comorbidities, and activity levels. Regardless of surgical treatment, complications such as infection, loosening or lysis, periprosthetic fracture, and postoperative pain are known risks and are indications for revision surgery. The clinical and economic implications for revision surgery are underappreciated. Over 55,000 revision surgeries were performed in 2010 in the US, with 48% of these revisions in patients under 65 years. Total costs associated with each revision TKA surgery have been estimated to be in excess of $49,000. The current annual economic burden of revision knee OA surgery is $2.7 billion for hospital charges alone. By 2030, assuming a 5-fold increase in the number of revision procedures, this economic burden will exceed $13 billion annually. It is appealing to envision a therapy that could delay or obviate the need for arthroplasty. From an actuarial standpoint, this would have the theoretical downstream effect of substantially reducing the number of revision procedures. Although no known therapies currently meet these criteria, such a breakthrough would have a tremendous impact in lessening the clinical and economic burden of knee OA revision surgery.

Revision Hip Arthroscopy: A Systematic Review of Diagnoses, Operative Findings, and Outcomes.

Science.gov (United States)

Cvetanovich, Gregory L; Harris, Joshua D; Erickson, Brandon J; Bach, Bernard R; Bush-Joseph, Charles A; Nho, Shane J

2015-07-01

To determine indications for, operative findings of, and outcomes of revision hip arthroscopy. A systematic review was registered with PROSPERO and performed based on PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines. Therapeutic clinical outcome studies reporting the indications for, operative findings of, and outcomes of revision hip arthroscopy were eligible for inclusion. All study-, patient-, and hip-specific data were extracted and analyzed. The Modified Coleman Methodology Score was used to assess study quality. Five studies were included (348 revision hip arthroscopies; 333 patients; mean age, 31.4 ± 4.2 years; 60% female patients). All 5 studies were either Level III or IV evidence. The surgeon performing revision hip arthroscopy was the same as the primary hip surgeon in only 25% of cases. The mean time between primary and revision hip arthroscopy was 27.8 ± 7.0 months (range, 2 to 193 months). Residual femoroacetabular impingement was the most common indication for and operative finding of revision hip arthroscopy (81% of cases). The most commonly reported revision procedures were femoral osteochondroplasty (24%) and acetabuloplasty (18%). The modified Harris Hip Score was used in all 5 analyzed studies, with significant (P arthroscopy, subsequent reported operations were hip arthroplasty in 11 patients and re-revision hip arthroscopy in 8 patients (5% total reoperation rate). Revision hip arthroscopy is most commonly performed for residual femoroacetabular impingement, with statistically significant and clinically relevant improvements shown in multiple patient-reported clinical outcome scores at short-term follow-up. The reoperation rate after revision hip arthroscopy is 5% within 2 years, including further arthroscopy or conversion to hip arthroplasty. Level IV, systematic review of Level III and IV studies. Copyright © 2015 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

C-018H LERF filtration test plan. Revision 1

International Nuclear Information System (INIS)

Moberg, T.P.; King, C.V.

1994-01-01

The following outlines the plan to test the polymeric backwash filtration system at the LERF. These tests will determine if the ETF filter design is adequate. If the tests show that the design is adequate, the task will be complete. If the tests show that the technology is inadequate, it may be necessary to perform further tests to qualify other candidate filtration technologies (e.g., polymeric tubular ultrafiltration, centrifugal ultrafiltration). The criteria to determine the success or failure of the backwash filter will be based on the system's ability to remove the bacteria and inorganic contaminants from the evaporator process condensate. The tests are designed to qualify the design basis of the filtration technology that will be used in the ETF

C-018H LERF filtration test plan. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Moberg, T.P.; King, C.V.

1994-08-26

The following outlines the plan to test the polymeric backwash filtration system at the LERF. These tests will determine if the ETF filter design is adequate. If the tests show that the design is adequate, the task will be complete. If the tests show that the technology is inadequate, it may be necessary to perform further tests to qualify other candidate filtration technologies (e.g., polymeric tubular ultrafiltration, centrifugal ultrafiltration). The criteria to determine the success or failure of the backwash filter will be based on the system`s ability to remove the bacteria and inorganic contaminants from the evaporator process condensate. The tests are designed to qualify the design basis of the filtration technology that will be used in the ETF.

High proximal migration in cemented acetabular revisions operated with bone impaction grafting; 47 revision cups followed with RSA for 17 years.

Science.gov (United States)

Mohaddes, Maziar; Herberts, Peter; Malchau, Henrik; Johanson, Per-Erik; Kärrholm, Johan

2017-05-12

Bone impaction grafting is a biologically and mechanically appealing option in acetabular revision surgery, allowing restitution of the bone stock and restoration of the biomechanics. We analysed differences in proximal migration of the revision acetabular components when bone impaction grafting is used together with a cemented or an uncemented cup. 43 patients (47 hips), revised due to acetabular loosening and judged to have less than 50% host bone-implant contact were included. The hips were randomised to either an uncemented (n = 20) or a cemented (n = 27) revision cup. Radiostereometry and radiography was performed postoperatively, at 3 and 6 months, 1, 2, 3, 5, 7, 10 and 13 and 17 years postoperatively. Clinical follow-up was performed at 1, 2 and 5 years postoperatively and thereafter at the same interval as in the radiographic follow-up. There were no differences in the base line demographic data between the 2 groups. At the last follow-up (17 years) 14 hips (10 cemented, 4 uncemented) had been re-revised due to loosening. 3 additional cups (1 uncemented and 2 cemented) were radiographically loose. There was a higher early proximal migration in the cemented cups. Cups operated on with cement showed a higher early migration measured with RSA and also a higher number of late revisions. The reason for this is not known, but factors such as inclusion of cases with severe bone defects, use of smaller bone chips and issues related to the impaction technique might have had various degrees of influence.

Inspection system performance test procedure

International Nuclear Information System (INIS)

Jensen, C.E.

1995-01-01

This procedure establishes requirements to administer a performance demonstration test. The test is to demonstrate that the double-shell tank inspection system (DSTIS) supplied by the contractor performs in accordance with the WHC-S-4108, Double-Shell Tank Ultrasonic Inspection Performance Specification, Rev. 2-A, January, 1995. The inspection system is intended to provide ultrasonic (UT) and visual data to determine integrity of the Westinghouse Hanford Company (WHC) site underground waste tanks. The robotic inspection system consists of the following major sub-systems (modules) and components: Mobile control center; Deployment module; Cable management assembly; Robot mechanism; Ultrasonic testing system; Visual testing system; Pneumatic system; Electrical system; and Control system

Revised

DEFF Research Database (Denmark)

Johannsen, Vivian Kvist; Nord-Larsen, Thomas; Riis-Nielsen, Torben

This report is a revised analysis of the Danish data on CO2 emissions from forest, afforestation and deforestation for the period 1990 - 2008 and a prognosis for the period until 2020. Revision have included measurements from 2009 in the estimations. The report is funded by the Ministry of Climate...

Double-shell tank integrity assessments ultrasonic test equipment performance test

Energy Technology Data Exchange (ETDEWEB)

Pfluger, D.C.

1996-09-26

A double-shell tank (DST) inspection (DSTI) system was performance tested over three months until August 1995 at Pittsburgh, Pennsylvania, completing a contract initiated in February 1993 to design, fabricate, and test an ultrasonic inspection system intended to provide ultrasonic test (UT) and visual data to determine the integrity of 28 DSTs at Hanford. The DSTs are approximately one-million-gallon underground radioactive-waste storage tanks. The test was performed in accordance with a procedure (Jensen 1995) that included requirements described in the contract specification (Pfluger 1995). This report documents the results of tests conducted to evaluate the performance of the DSTI system against the requirements of the contract specification. The test of the DSTI system also reflects the performance of qualified personnel and operating procedures.

Sex Differences in Performance over 7 Years on the Wechsler Intelligence Scale for Children Revised among Adults with Intellectual Disability

Science.gov (United States)

Kittler, P.; Krinsky-McHale, S. J.; Devenny, D. A.

2004-01-01

The aim of this study was to explore changes related to sex differences on the Wechsler Intelligence Scale for Children Revised (WISC-R) subtest performance over a 7-year interval in middle-aged adults with intellectual disability (ID). Cognitive sex differences have been extensively studied in the general population, but there are few reports…

Selection of a computer code for Hanford low-level waste engineered-system performance assessment. Revision 1

International Nuclear Information System (INIS)

McGrail, B.P.; Bacon, D.H.

1998-02-01

Planned performance assessments for the proposed disposal of low-activity waste (LAW) glass produced from remediation of wastes stored in underground tanks at Hanford, Washington will require calculations of radionuclide release rates from the subsurface disposal facility. These calculations will be done with the aid of computer codes. The available computer codes with suitable capabilities at the time Revision 0 of this document was prepared were ranked in terms of the feature sets implemented in the code that match a set of physical, chemical, numerical, and functional capabilities needed to assess release rates from the engineered system. The needed capabilities were identified from an analysis of the important physical and chemical processes expected to affect LAW glass corrosion and the mobility of radionuclides. This analysis was repeated in this report but updated to include additional processes that have been found to be important since Revision 0 was issued and to include additional codes that have been released. The highest ranked computer code was found to be the STORM code developed at PNNL for the US Department of Energy for evaluation of arid land disposal sites

Fire testing and analysis of TRUPACT-I Thermal Test Article

International Nuclear Information System (INIS)

Romesberg, L.E.; Longenbaugh, R.S.; Joseph, B.J.

1989-02-01

This report documents the fabrication and thermal test of a full-scale prototype of the revised TRUPACT-I design. The fire test demonstrated that the response of the Test Article to a jet-fueled pool fire, subsequent to the impact and puncture tests, meets the impact, puncture, and thermal performance requirements of the regulations governing transport of radioactive materials. The Test Article was a replica of the front half (closure end) of the revised TRUPACT-I design. To simulate the cumulative effect of the regulatory hypothetical accident sequence, the Test Article included the structural damage found in TRUPACT-I, Unit 0 after regulatory drop and puncture testing. The Test Article was totally engulfed in a pool fire fueled by JP-4 jet fuel for 46 minutes. The maximum temperature reached at the inner door seals was 149/degree/C (300/degree/F) and the maximum temperature at the inner door filters was 171/degree/C (340/degree/F). Both temperatures are within the normal working range for these components. Post-test leak rate measurements of 0.0041 atm-cm 3 /s (ANSI standard air) between the innermost pair of door seals and 0.0046 atm-cm 3 /s (ANSI standard air) between the outermost pair of door seals verified that the performance of the silicone seals met the design requirements. Since no detectable leakage was measured to a sensitivity of 1.0E-7 atm-cm 3 /s for the filter installation seal or quick-connect valve seal post-test, the total leak rate for the containment system was less than the maximum allowable 0.01 atm-cm 3 /s (ANSI standard air). 10 refs., 52 figs., 5 tabs

Changes in chemistry and biochemistry education: creative responses to medical college admissions test revisions in the age of the genome.

Science.gov (United States)

Brenner, Charles

2013-01-01

Approximately two million students matriculate into American colleges and universities per year. Almost 20% of these students begin taking a series of courses specified by advisers of health preprofessionals. The single most important influence on health profession advisers and on course selection for this huge population of learners is the Medical College Admissions Test (MCAT), which was last revised in 1991, 10 years before publication of the first draft human genome sequence. In preparation for the 2015 MCAT, there is a broad discussion among stakeholders of how best to revise undergraduate and medical education in the molecular sciences to prepare researchers and doctors to acquire, analyze and use individual genomic and metabolomic data in the coming decades. Getting these changes right is among the most important educational problems of our era. Copyright © 2012 International Union of Biochemistry and Molecular Biology, Inc.

Revision Vodcast Influence on Assessment Scores and Study Processes in Secondary Physics

Science.gov (United States)

Marencik, Joseph J.

A quasi-experimental switching replications design with matched participants was employed to determine the influence of revision vodcasts, or video podcasts, on students' assessment scores and study processes in secondary physics. This study satisfied a need for quantitative results in the area of vodcast influence on students' learning processes. Thirty-eight physics students in an urban Ohio public high school participated in the study. The students in one Physics class were paired with students in another Physics class through the matching characteristics of current student cumulative test score mean and baseline study process as measured by the Study Process Questionnaire (SPQ). Students in both classes were given identical pedagogic treatment and access to traditional revision tools except for the supplemental revision vodcasts given to the experimental group. After students in the experimental group viewed the revision vodcast for a particular topic, the assessment scores of the students in the experimental group were compared to the assessment scores of the control group through the direct-difference, D, test to determine any difference between the assessment score means of each group. The SPQ was given at the beginning of the experiment and after each physics assessment. The direct-difference method was again used to determine any difference between the SPQ deep approach scores of each group. The SPQ was also used to determine any correlative effects between study process and revision vodcast use on students' assessment scores through descriptive statistics and an analysis of variance (ANOVA) test. Analysis indicated that revision vodcast use significantly increased students' assessment scores (p.05). There were no significant correlative effects of revision vodcast use and study processes on students' assessment scores (p>.05). This study offers educators the empirical support to devote the necessary effort, time, and resources into developing successful

LFK, FORTRAN Application Performance Test

International Nuclear Information System (INIS)

McMahon, F.H.

1991-01-01

1 - Description of program or function: LFK, the Livermore FORTRAN Kernels, is a computer performance test that measures a realistic floating-point performance range for FORTRAN applications. Informally known as the Livermore Loops test, the LFK test may be used as a computer performance test, as a test of compiler accuracy (via checksums) and efficiency, or as a hardware endurance test. The LFK test, which focuses on FORTRAN as used in computational physics, measures the joint performance of the computer CPU, the compiler, and the computational structures in units of Mega-flops/sec or Mflops. A C language version of subroutine KERNEL is also included which executes 24 samples of C numerical computation. The 24 kernels are a hydrodynamics code fragment, a fragment from an incomplete Cholesky conjugate gradient code, the standard inner product function of linear algebra, a fragment from a banded linear equations routine, a segment of a tridiagonal elimination routine, an example of a general linear recurrence equation, an equation of state fragment, part of an alternating direction implicit integration code, an integrate predictor code, a difference predictor code, a first sum, a first difference, a fragment from a two-dimensional particle-in-cell code, a part of a one-dimensional particle-in-cell code, an example of how casually FORTRAN can be written, a Monte Carlo search loop, an example of an implicit conditional computation, a fragment of a two-dimensional explicit hydrodynamics code, a general linear recurrence equation, part of a discrete ordinates transport program, a simple matrix calculation, a segment of a Planck distribution procedure, a two-dimensional implicit hydrodynamics fragment, and determination of the location of the first minimum in an array. 2 - Method of solution: CPU performance rates depend strongly on the maturity of FORTRAN compiler machine code optimization. The LFK test-bed executes the set of 24 kernels three times, resetting the DO

Operational test report for LERF Basin 242AL-44 integrity test

International Nuclear Information System (INIS)

Galioto, T.M.

1994-01-01

This operational test report documents the results of LERF operational testing per operational test procedure (OTP) TFPE-WP-0231, ''LERF Basin Integrity Testing.'' The primary purpose of the OTP was to resolve test exceptions generated as a result of TFPE-WP-0184. The TOP was prepared and performed in accordance with WHC-SD-534-OTP-002, ''Operational Test Plan for the 242-A Evaporator Upgrades and the Liquid Effluent Retention Facility.'' WHC-S-086, ''Specification for Operational Testing of the Liquid Effluent Retention Facility, Basin Integrity Testing,'' identified the test requirements and acceptance criteria. The completed, signed-off test procedure is contained in Appendix A. The test log is contained in Appendix B. Section 2.1 describes all the test exceptions written during performance of the Operational Test Procedure. The test revisions generated during the testing are discussed in Section 2.2. The dispositioned test exception forms are contained in Appendix C

Test planning and performance

International Nuclear Information System (INIS)

Zola, Maurizio

2001-01-01

Testing plan should include Safety guide Q4 - Inspection and testing - A testing plan should be prepared including following information: General information (facility name, item or system reference, procurement document reference, document reference number and status, associated procedures and drawings); A sequential listing of all testing activities; Procedure, work instruction, specification or standard to be followed in respect of each operation and test; Acceptance criteria; Identification of who is performing tests; Identification of hold points; Type of records to be prepared for each test; Persons and organizations having authority for final acceptance. Proposed activities sequence is: visual, electrical and mechanical checks; environmental tests (thermal aging, vibrations aging, radioactive aging); performance evaluation in extreme conditions; dynamic tests with functional checks; final electrical and mechanical checks The planning of the tests should always be performed taking into account an interpretative model: a very tight cooperation is advisable between experimental people and numerical people dealing with the analysis of more or less complex models for the seismic assessment of structures and components. Preparatory phase should include the choice of the following items should be agreed upon with the final user of the tests: Excitation points, Excitation types, Excitation amplitude with respect to frequency, Measuring points. Data acquisition, recording and storage, should take into account the characteristics of the successive data processing: to much data can be cumbersome to be processed, but to few data can make unusable the experimental results. The parameters for time history acquisition should be chosen taking into account data processing: for Shock Response Spectrum calculation some special requirements should be met: frequency bounded signal, high frequency sampling, shock noise. For stationary random-like excitation, the sample length

Radioactive material packaging performance testing

International Nuclear Information System (INIS)

Romano, T.; Cruse, J.M.

1991-02-01

To provide uniform packaging of hazardous materials on an international level, the United Nations has developed packaging recommendations that have been implemented worldwide. The United Nations packaging recommendations are performance oriented, allowing for a wide variety of package materials and systems. As a result of this international standard, efforts in the United States are being directed toward use of performance-oriented packaging and elimination of specification (designed) packaging. This presentation will focus on trends, design evaluation, and performance testing of radioactive material packaging. The impacts of US Department of Transportation Dockets HM-181 and HM-169A on specification and low-specific activity radioactive material packaging requirements are briefly discussed. The US Department of Energy's program for evaluating radioactive material packings per US Department of Transportation Specification 7A Type A requirements, is used as the basis for discussing low-activity packaging performance test requirements. High-activity package testing requirements are presented with examples of testing performed at the Hanford Site that is operated by Westinghouse Hanford Company for the US Department of Energy. 5 refs., 2 tabs

REVISION ANKLE SYNDESMOSIS FIXATION - FUNCTIONAL OUTCOME AFTER TIGHTROPE ® FIXATION

Directory of Open Access Journals (Sweden)

Sendhilvelan Rajagopalan

2016-07-01

Full Text Available BACKGROUND Syndesmotic disruptions are often seen in ankle fractures. Malreduction of these fractures can result in arthritis and instability. A proportion of these patients with malreduction require revision fixation. This study presents the results of revision fixation in such patients, using the Ankle TightRope ® (Arthrex system. METHODS Between January 2000 to December 2009, 124 patients who underwent ankle fracture fixations with syndesmotic stabilisation were analysed. Out of 124 patients, 8 patients were diagnosed with failure of primary stabilisation (based on radiological and clinical criteria and subjected to revision fixation using the Ankle TightRope ® (Arthrex system. Followup was done at periodic time intervals of 3, 6 and 12 months. Both clinical and radiological assessment was performed. Complications and duration of hospital stay was recorded. Functional evaluation was performed using the American Orthopaedic Foot and Ankle Society (AOFAS scoring system. RESULTS Five patients had good results, one satisfactory and two had poor outcomes. CONCLUSIONS Ankle TightRope ® fixation is an alternative method of stabilisation in patients who require revision syndesmosis fixation. Further studies are required to evaluate this method of revision stabilisation as compared to screws.

L2 Writing in Test and Non-test Situations: Process and Product

Directory of Open Access Journals (Sweden)

Baraa Khuder

2015-02-01

Full Text Available Test writers sometimes complain they cannot perform to their true abilities because of time constraints. We therefore examined differences in terms of process and product between texts produced under test and non-test conditions. Ten L2 postgraduates wrote two argumentative essays, one under test conditions, with only forty minutes being allowed and without recourse to resources, and one under non-test conditions, with unlimited time as well as access to the Internet. Keystroke logging, screen capture software, and stimulated recall protocols were used, participants explaining and commenting on their writing processes. Sixteen writing process types were identified. Higher proportions of the processes of translation and surface revision were recorded in the test situation, while meaningful revision and evaluation were both higher in the non-test situation. There was a statistically significant difference between time allocation for different processes at different stages. Experienced teachers awarded the non-test texts a mean score of almost one point (0.8 higher. A correlational analysis examining the relationship between writing process and product quality showed that while the distribution of writing processes can have an impact on text quality in the test situation, it had no effect on the product in the non-test situation.

Uniform peanut performance test 2017

Science.gov (United States)

The Uniform Peanut Performance Tests (UPPT) are designed to evaluate the commercial potential of advanced breeding peanut lines not formally released. The tests are performed in ten locations across the peanut production belt. In this study, 2 controls and 14 entries were evaluated at 8 locations....

ORCWM test and evaluaton master plan. Revision 00

International Nuclear Information System (INIS)

1995-08-01

The Office of Civilian Radioactive Waste Management (OCRWM) Test and Evaluation Master Plan (TEMP) describes the program Test and Evaluation (T ampersand E) policy, objectives, requirements, general methodology (test flow and description of each T ampersand E phase), responsibilities, and scheduling of test phases for the Civilian Radioactive Waste Management System (CRWMS). This TEMP is a program-level management planning document for al CRWMS T ampersand E activities and will be used in conjunction with Section 11 of the Quality Assurance Requirements and Description (QARD), as appropriate, as a guide for the projects in developing their T ampersand E plans. In the OCRWM document hierarchy, that is described in the OCRWM Systems Engineering Management Plan (SEMP), the TEMP is subordinate to the program SEMP. To ensure CRWMS operates as an integrated system, the plans for verifying the performance and evaluating the operational suitability and effectiveness of the overall system are also described. Test and evaluation is an integral part of the systems engineering process. Key aspects of the systems engineering process, more fully described in the OCRWM SEMP, are discussed in this TEMP to illustrate how T ampersand E supports the overall systems engineering process

Test Blanket Working Group's recent activities

International Nuclear Information System (INIS)

Vetter, J.E.

2001-01-01

The ITER Test Blanket Working Group (TBWG) has continued its activities during the period of extension of the EDA with a revised charter on the co-ordination of the development work performed by the Parties and by the JCT leading to a co-ordinated test programme on ITER for a DEMO-relevant tritium breeding blanket. This follows earlier work carried out until July 1998, which formed part of the ITER Final Design Report (FDR), completed in 1998. Whilst the machine parameters for ITER-FEAT have been significantly revised compared to the FDR, testing of breeding blanket modules remains a main objective of the test programme and the development of a reactor-relevant breeding blanket to ensure tritium fuel self-sufficiency is recognized a key issue for fusion. Design work and R and D on breeding blanket concepts, including co-operation with the other Contacting Parties of the ITER-EDA for testing these concepts in ITER, are included in the work plans of the Parties

200 area liquid effluent facility quality assurance program plan. Revision 1

International Nuclear Information System (INIS)

Sullivan, N.J.

1995-01-01

Direct revision of Supporting Document WHC-SD-LEF-QAPP-001, Rev. 0. 200 Area Liquid Effluent Facilities Quality Assurance Program Plan. Incorporates changes to references in tables. Revises test to incorporate WHC-SD-LEF-CSCM-001, Computer Software Configuration Management Plan for 200 East/West Liquid Effluent Facilities

The Morse taper junction in modular revision hip replacement--a biomechanical and retrieval analysis.

Science.gov (United States)

Schramm, M; Wirtz, D C; Holzwarth, U; Pitto, R P

2000-04-01

All biomaterials used for total joint surgery are subjected to wear mechanisms. Morse taper junctions of modular hip revision implants are predilection sites for both fretting and crevice corrosion, dissociation and breakage of the components. The aim of this study is to quantify wear and study metallurgical changes of Morse taper junctions of in-vitro and in-vivo loaded modular revision stems. Three modular revision stems (MRP-Titan, Peter Brehm GmbH, Germany) were loaded by a servohydraulic testing machine. The loads and conditions used exceeded by far the values required by ISO-standard 7206. The tests were performed with maximum axial loads of 3,500 N to 4,000 N over 10-12 x 10(6) cycles at 2 Hz. Additionally, the female part of the taper junctions were coated with blood and bone debris. The free length of the implant was set to 200 mm. One other MRP stem was investigated after retrieval following 5.5 years of in-vivo use. All contact surfaces of the modular elements were assessed by visual inspection, optical microscopy and scanning electron microscopy (SEM). The degree of plastic deformation of the male part of the morse taper junction was determined by contouroscopy. None of the morse taper junctions broke or failed mechanically. Corrosion and wear affected all tapers, especially at the medial side. The retrieved implant showed no cracks and the amount of debris measured only one third of that for the stems tested in-vitro. The present retrieval and laboratory investigations have proven, that the morse taper junctions of the MRP-titanium stem are stable and resistant to relevant wear mechanisms. The longevity of the junctions for clinical use is given. If an optimal taper design is selected, the advantages of modular femoral components in total hip revision arthroplasty will outweigh the possible risks.

Integral test of JENDL-3.3 on fast reactors

International Nuclear Information System (INIS)

Chiba, Gou; Hazama, Taira

2003-05-01

An integral test has been carried out to evaluate a performance of evaluated nuclear data library JENDL-3.3, which was newly released, in a view of applying neutronics analyses of fast reactors. Japan Nuclear Cycle Development Institute has a large amount of data of critical assembly experiments (ZPPR, BFS, MOZART and FCA) and power reactor tests (JOYO). The database was utilized in this test. In plutonium loaded cores, an improvement was observed about 0.3% ε k in criticality and 5% in the non-leakage term of sodium void reactivity by a revision form JENDL-3.2 to -3.3. These results shoed that the revision is valid in plutonium loaded cores. In uranium loaded cores, dependence of C/E values on control rod position became smaller in control rod worth in ZPPR cores. On the other hand, C/E values became worse both in criticality (0.6%εk) and in sodium void reactivity (30%) in BFS cores. The main cause was a revision of uranium-235 capture cross section, and it could not be concluded whether the revision is valid or not in uranium loaded cores. It is necessary to carry out a validation test at other independent critical experiments in which uranium fuel is used. (author)

Revising superior planning performance in chess players: the impact of time restriction and motivation aspects.

Science.gov (United States)

Unterrainer, Josef Martin; Kaller, Christoph Philipp; Leonhart, Rainer; Rahm, Benjamin

2011-01-01

In a previous study (Unterrainer, Kaller, Halsband, & Rahm, 2006), chess players outperformed non-chess players in the Tower of London planning task but exhibited disproportionately longer processing times. This pattern of results raises the question of whether chess players' planning capabilities are superior or whether the results reflect differences in the speed-accuracy trade-off between the groups, possibly attributable to sports motivation. The present study was designed to disambiguate these alternative suggestions by implementing various constraints on planning time and by assessing self-reported motivation. In contrast to the previous study, chess players' performance was not superior, independently of whether problems had to be solved with (Experiment 1) or without (Experiment 2) time limits. As expected, chess players reported higher overall trait and state motivation scores across both experiments. These findings revise the notion of superior planning performance in chess players. In consequence, they do not conform with the assumption of a general transfer of chess-related planning expertise to other cognitive domains, instead suggesting that superior performance may be possible only under specific circumstances such as receiving competitive instructions.

Revision of nuclear power plants safety systems' routine testing assigned periodicity during the design extension period

International Nuclear Information System (INIS)

Skalozubov, V.I.; Kozlov, Yi.L.; Chulkyin, O.O.

2017-01-01

When nuclear power plants safety systems thermal equipment operation extending, a necessary requirement shall rely on revising the scheduled equipment tests frequency to optimize those tests schedule taking into account the equipment remained lifespan. On the one hand, there exists a need for tests frequency increase to detect ''hidden'' failures, and on the another, frequent tests cause a premature wear of the equipment. Proposed is an original method for optimizing the frequency of NPPs safety systems thermal engineering equipment testing. Essential in the proposed method is the optimization criterion chosen: index of security system failure probability non-exceedance during the beyond-design operating period as referred to the failure probability expected considering the equipment residual resource during the design operating period. The developed method implementation when applied to NPPs safety systems operated beyond the design service life at nuclear power plants with WWER-1000 series reactors, allowed to establish that the optimal tests frequency makes half the designed one when the equipment service life is extended by five years and three times less that the designed frequency when subject lifespan extended by 10 years.

40 CFR 63.344 - Performance test requirements and test methods.

Science.gov (United States)

2010-07-01

... electroplating tanks or chromium anodizing tanks. The sampling time and sample volume for each run of Methods 306... Chromium Anodizing Tanks § 63.344 Performance test requirements and test methods. (a) Performance test... Emissions From Decorative and Hard Chromium Electroplating and Anodizing Operations,” appendix A of this...

The Effects of the Revised CPPNM on Legislative Framework

International Nuclear Information System (INIS)

Kwak, Sung-Woo; Yoo, Ho-Sik; Shim, Hye-Won; Chang, Sun-Young; Lee, Jong-Uk

2006-01-01

A Diplomatic Conference was held last July at Vienna of Austria and adopted an important Convention in physical protection field. The Convention is the revised Convention on Physical Protection of Nuclear Material. A State Party to the revised CPPNM has obligation to meet the Convention. Since the Amendment to CPPNM is expected to enter into force in near future, there is an urgent need to prepare for implementing the international obligation. Thus, it is important to assess the effect of the revised Convention on national legislative and regulatory framework to govern physical protection of domestic nuclear material and facilities. The objective of this paper is to perform comparative assessment between new provisions of the revised Convention and national law in order to prepare for the implementation of the international norm

Psychometric Evaluation of the Revised Michigan Diabetes Knowledge Test (V.2016) in Arabic: Translation and Validation

Science.gov (United States)

Alhaiti, Ali Hassan; Alotaibi, Alanod Raffa; Jones, Linda Katherine; DaCosta, Cliff

2016-01-01

Objective. To translate the revised Michigan Diabetes Knowledge Test into the Arabic language and examine its psychometric properties. Setting. Of the 139 participants recruited through King Fahad Medical City in Riyadh, Saudi Arabia, 34 agreed to the second-round sample for retesting purposes. Methods. The translation process followed the World Health Organization's guidelines for the translation and adaptation of instruments. All translations were examined for their validity and reliability. Results. The translation process revealed excellent results throughout all stages. The Arabic version received 0.75 for internal consistency via Cronbach's alpha test and excellent outcomes in terms of the test-retest reliability of the instrument with a mean of 0.90 infraclass correlation coefficient. It also received positive content validity index scores. The item-level content validity index for all instrument scales fell between 0.83 and 1 with a mean scale-level index of 0.96. Conclusion. The Arabic version is proven to be a reliable and valid measure of patient's knowledge that is ready to be used in clinical practices. PMID:27995149

Impact of revised 10 CFR 20 on existing performance assessment computer codes used for LLW disposal facilities

International Nuclear Information System (INIS)

Leonard, P.R.; Seitz, R.R.

1992-04-01

The US Nuclear Regulatory Commission (NRC) recently announced a revision to Chapter 10 of the Code of Federal Regulations, Part 20 (10 CFR 20) ''Standards for Protection Against Radiation,'' which incorporates recommendations contained in Publications 26 and 30 of the International Commission on Radiological Protection (ICRP), issued in 1977 and 1979, respectively. The revision to 10 CFR 20 was also developed in parallel with Presidential Guidance on occupational radiation protection published in the Federal Register. Thus, this study concludes that the issuance of the revised 10 CFR 20 will not affect calculations using the computer codes considered in this report. In general, the computer codes and EPA and DOE guidance on which computer codes are based were developed in a manner consistent with the guidance provided in ICRP 26/30, well before the revision of 10 CFR 20

Revision for prosthetic joint infection following hip arthroplasty: Evidence from the National Joint Registry.

Science.gov (United States)

Lenguerrand, E; Whitehouse, M R; Beswick, A D; Jones, S A; Porter, M L; Blom, A W

2017-06-01

We used the National Joint Registry for England, Wales, Northern Ireland and the Isle of Man (NJR) to investigate the risk of revision due to prosthetic joint infection (PJI) for patients undergoing primary and revision hip arthroplasty, the changes in risk over time, and the overall burden created by PJI. We analysed revision total hip arthroplasties (THAs) performed due to a diagnosis of PJI and the linked index procedures recorded in the NJR between 2003 and 2014. The cohort analysed consisted of 623 253 index primary hip arthroplasties, 63 222 index revision hip arthroplasties and 7585 revision THAs performed due to a diagnosis of PJI. The prevalence, cumulative incidence functions and the burden of PJI (total procedures) were calculated. Overall linear trends were investigated with log-linear regression. We demonstrated a prevalence of revision THA due to prosthetic joint infection of 0.4/100 procedures following primary and 1.6/100 procedures following revision hip arthroplasty. The prevalence of revision due to PJI in the three months following primary hip arthroplasty has risen 2.3-fold (95% confidence interval (CI) 1.3 to 4.1) between 2005 and 2013, and 3.0-fold (95% CI 1.1 to 8.5) following revision hip arthroplasty. Over 1000 procedures are performed annually as a consequence of hip PJI, an increase of 2.6-fold between 2005 and 2013. Although the risk of revision due to PJI following hip arthroplasty is low, it is rising and, coupled with the established and further predicted increased incidence of both primary and revision hip arthroplasty, this represents a growing and substantial treatment burden. Cite this article : E. Lenguerrand, M. R. Whitehouse, A. D. Beswick, S. A. Jones, M. L. Porter, A. W. Blom. Revision for prosthetic joint infection following hip arthroplasty: Evidence from the National Joint Registry. Bone Joint Res 2017;6:391-398. DOI: 10.1302/2046-3758.66.BJR-2017-0003.R1. © 2017 Lenguerrand et al.

Summary report of the experimental fast reactor JOYO MK-III performance test

International Nuclear Information System (INIS)

Maeda, Yukimoto; Aoyama, Takafumi; Yoshida, Akihiro

2004-03-01

An upgrading project (MK-III project) was started to improve the irradiation capability of the experimental fast reactor JOYO. In this project, core replacement and increase of the reactor thermal power by the factor 1.4 were necessary for increasing the maximum fast neutron flux by the factor 1.3 and doubling the capacity for irradiation rigs. The modification of the cooling system that included the replacement of the main intermediate heat exchangers and the dump heat exchangers was completed in September 2000. After a series of system function tests, the performance test, of which objective is to fully characterize the upgraded core and heat transfer system, was started in June 2003. Twenty eight tests were selected and carried out as performance test, in order to confirm that the whole plant satisfy the design criteria and have sufficient characteristics (data necessary for safe and steady operation, core management, reactor control and monitoring) as an irradiation bed. After attaining the initial criticality of the core on 2nd July 2003, core characteristics (the excess reactivity, the isotherm temperature reactivity coefficient, the power reactivity coefficient and so on), plant characteristics (the plant heat balance, the adjustment of the temperature control system, the plant behavior at transient), shielding characteristics (dose rate distribution). As the result, it was confirmed that all the criteria regulated was satisfied and the core and plant have sufficient margins for full power operation, which was increased by the factor 1.4. Especially, nuclear analysis accuracy was verified by comparing the calculation with measured core characteristics of the initial core which consists of fifty five fresh fuel subassemblies. The operational data which is supposed to be useful for developing in-core anomaly detection system were also obtained. The operation manual and training simulator and design of next reactor development were revised based on the results

EPRI PWR primary water chemistry guidelines revision

International Nuclear Information System (INIS)

McElrath, Joel; Fruzzetti, Keith

2014-01-01

EPRI periodically updates the PWR Primary Water Chemistry Guidelines as new information becomes available and as required by NEI 97-06 (Steam Generator Program Guidelines) and NEI 03-08 (Guideline for the Management of Materials Issues). The last revision of the PWR water chemistry guidelines identified an optimum primary water chemistry program based on then-current understanding of research and field information. This new revision provides further details with regard to primary water stress corrosion cracking (PWSCC), fuel integrity, and shutdown dose rates. A committee of industry experts, including utility specialists, nuclear steam supply system (NSSS) and fuel vendor representatives, Institute of Nuclear Power Operations (INPO) representatives, consultants, and EPRI staff collaborated in reviewing the available data on primary water chemistry, reactor water coolant system materials issues, fuel integrity and performance issues, and radiation dose rate issues. From the data, the committee updated the water chemistry guidelines that all PWR nuclear plants should adopt. The committee revised guidance with regard to optimization to reflect industry experience gained since the publication of Revision 6. Among the changes, the technical information regarding the impact of zinc injection on PWSCC initiation and dose rate reduction has been updated to reflect the current level of knowledge within the industry. Similarly, industry experience with elevated lithium concentrations with regard to fuel performance and radiation dose rates has been updated to reflect data collected to date. Recognizing that each nuclear plant owner has a unique set of design, operating, and corporate concerns, the guidelines committee has retained a method for plant-specific optimization. Revision 7 of the Pressurized Water Reactor Primary Water Chemistry Guidelines provides guidance for PWR primary systems of all manufacture and design. The guidelines continue to emphasize plant

Stereotype Threat, Test Anxiety, and Mathematics Performance

Science.gov (United States)

Tempel, Tobias; Neumann, Roland

2014-01-01

We investigated the combined effects of stereotype threat and trait test anxiety on mathematics test performance. Stereotype threat and test anxiety interacted with each other in affecting performance. Trait test anxiety predicted performance only in a diagnostic condition that prevented stereotype threat by stereotype denial. A state measure of…

Establishing placement test fit and performance: Serving local needs

Directory of Open Access Journals (Sweden)

Gerriet Janssens

2013-07-01

Full Text Available Accountability in language education is often associated with top-down national policies unresponsive—or even hostile to—local needs; however, when accountability is driven by local stakeholders seeking to better understand and enhance their programs, it can foster productive cycles of action research and curriculum development. This paper reports on one such internally-motivated accountability effort, in which program insiders sought to determine the efficacy of a reading test being administered to a new population of students at one Colombian university. Descriptive statistics, reliability estimates, and item facility and discrimination measures were used to determine whether this test was sufficiently reliable and appropriately matched to test takers’ ability in order to warrant its use as part of a high-stakes English-language placement exam. A detailed analysis of this test is used not only to propose specific recommendations for revision but also to illustrate a useful set of statistical tools appropriate for test analysis in other language programs. Moreover, we conclude that the involvement of local instructors as part of an iterative, self-reflective, test development process provides opportunities for professional development and deeper engagement in accountability projects.

Comparing the functional performance of children and youths with autism, developmental disabilities, and no disability using the revised pediatric evaluation of disability inventory item banks.

Science.gov (United States)

Kao, Ying-Chia; Kramer, Jessica M; Liljenquist, Kendra; Tian, Feng; Coster, Wendy J

2012-01-01

OBJECTIVE. We compared the functional performance of children with autism spectrum disorders (ASD), intellectual and developmental disabilities (IDD), and without disabilities using the revised Pediatric Evaluation of Disability Inventory-Computer Adaptive Test (PEDI-CAT) Social/Cognitive, Daily Activities, and Responsibility domains. METHOD. A nationally representative sample of parents of children ages 0-21 without disabilities (n = 2,205), with ASD (n = 108), or with IDD (n = 150) completed an online survey. We obtained predicted PEDI-CAT scaled scores for three reference ages (5, 10, 15) from a modified analysis of covariance model and compared each group's scores using contrasts of the regression parameters. RESULTS. We found no significant differences between the ASD and IDD groups. The group with ASD demonstrated significantly lower performance than the group without disabilities across the three domains at ages 10 and 15. CONCLUSION. Scores on the PEDI-CAT differentiated the group with ASD from the group without disabilities. Children with ASD and IDD did not demonstrate different performance profiles. Copyright © 2012 by the American Occupational Therapy Association, Inc.

Large shaft development test plan

International Nuclear Information System (INIS)

Krug, A.D.

1984-03-01

This test plan proposes the conduct of a large shaft development test at the Hanford site in support of the repository development program. The purpose and objective of the test plan is to obtain the information necessary to establish feasibility and to predict the performance of the drilling system used to drill large diameter shafts. The test plan is based upon drilling a 20 ft diameter shaft to a depth of 1,000 feet. The test plan specifies series of tests to evaluate the performance of the downhole assembly, the performance of the rig, and the ability of the system to cope with geologic hazards. The quality of the hole produced will also be determined. This test plan is considered to be preliminary in that it was prepared as input for the decision to determine if development testing is required in this area. Should the decision be made to proceed with development testing, this test plan shall be updated and revised. 6 refs., 2 figs., 3 tabs

Perioperative transfusion threshold and ambulation after hip revision surgery

DEFF Research Database (Denmark)

Nielsen, Kamilla; Johansson, Pär I; Dahl, Benny

2014-01-01

BACKGROUND: Transfusion with red blood cells (RBC) may be needed during hip revision surgery but the appropriate haemoglobin concentration (Hb) threshold for transfusion has not been well established. We hypothesized that a higher transfusion threshold would improve ambulation after hip revision...... surgery. METHODS: The trial was registered at Clinicaltrials.gov ( NCT00906295). Sixty-six patients aged 18 years or older undergoing hip revision surgery were randomized to receive RBC at a Hb threshold of either 7.3 g/dL (restrictive group) or 8.9 g/dL (liberal group). Postoperative ambulation...... received RBC. CONCLUSIONS: A Hb transfusion threshold of 8.9 g/dL was associated with a statistically significantly faster TUG after hip revision surgery compared to a threshold of 7.3 g/dL but the clinical importance is questionable and the groups did not differ in Hb at the time of testing....

EPRI BWR Water Chemistry Guidelines Revision

International Nuclear Information System (INIS)

Garcia, Susan E.; Giannelli, Joseph F.

2014-01-01

BWRVIP-190: BWR Water Chemistry Guidelines – 2008 Revision has been revised. The revision committee consisted of U.S. and non-U.S. utilities (members of the BWR Vessel and Internals Protection (BWRVIP) Mitigation Committee), reactor system manufacturers, fuel suppliers, and EPRI and industry experts. The revised document, BWRVIP-190 Revision 1, was completely reformatted into two volumes, with a simplified presentation of water chemistry control, diagnostic and good practice parameters in Volume 1 and the technical bases in Volume 2, to facilitate use. The revision was developed in parallel and in coordination with preparation of the Fuel Reliability Guidelines Revision 1: BWR Fuel Cladding Crud and Corrosion. Guidance is included for plants operating under normal water chemistry (NWC), moderate hydrogen water chemistry (HWC-M), and noble metal application (GE-Hitachi NobleChem™) plus hydrogen injection. Volume 1 includes significant changes to BWR feedwater and reactor water chemistry control parameters to provide increased assurance of intergranular stress corrosion cracking (IGSCC) mitigation of reactor materials and fuel reliability during all plant conditions, including cold shutdown (≤200°F (93°C)), startup/hot standby (>200°F (93°C) and ≤ 10%) and power operation (>10% power). Action Level values for chloride and sulfate have been tightened to minimize environmentally assisted cracking (EAC) of all wetted surfaces, including those not protected by hydrogen injection, with or without noble metals. Chemistry control guidance has been enhanced to minimize shutdown radiation fields by clarifying targets for depleted zinc oxide (DZO) injection while meeting requirements for fuel reliability. Improved tabular presentations of parameter values explicitly indicate levels at which actions are to be taken and required sampling frequencies. Volume 2 provides the technical bases for BWR water chemistry control for control of EAC, flow accelerated corrosion

Air and radon pathways screenings methodologies for the next revision of the E-area PA

Energy Technology Data Exchange (ETDEWEB)

Dyer, J. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-10-31

The strategic plan for the next E-Area Low-Level Waste Facility Performance Assessment includes recommended changes to the screening criteria used to reduce the number of radioisotopes that are to be considered in the air and radon pathways incorporated into the GoldSim® atmospheric release model (ARM). For the air pathway, a revised screening methodology was developed based on refinement of previous E-Area PA screening approaches and consideration of the strategic plan recommendations. The revised methodology has three sequential screening steps for each radioisotope: (1) volatility test using the Periodic Table of the Elements, (2) stability test based on half-life, and (3) stability test based on volatility as measured by the Henry’s Law constant for the assumed dominant gaseous species or vapor pressure in the case of tritiated water. Of the 1252 radioisotopes listed in the International Commission on Radiological Protection Publication 107, only the 10 that satisfied all three steps of the revised screening methodology will be included in the ARM. They are: Ar-37, Ar-39, Ar-42, C-14, H-3, Hg-194, Hg-203, Kr-81, Kr-85, and Xe-127. For the radon pathway, a revised screening methodology was developed that also has three sequential steps: (1) identify all decay chains that terminate at Rn-222, (2) screen out parents that decay through U-238 because of its 4.5-billion-year primordial half-life, and (3) eliminate remaining parents whose half-life is shorter than one day. Of the 86 possible decay chains leading to Rn-222, six decay chains consist of 15 unique radioisotopes that will be incorporated into the ARM. The 15 radioisotopes are: U-238, Th-234, Pa-234m, Pu-238, U-234, Th-230, Ra-226, Cf-246, Cm-242, Am-242m, Am-242, Np-238, Np-234, Pa-230, and Rn-222.

Effort, symptom validity testing, performance validity testing and traumatic brain injury.

Science.gov (United States)

Bigler, Erin D

2014-01-01

To understand the neurocognitive effects of brain injury, valid neuropsychological test findings are paramount. This review examines the research on what has been referred to a symptom validity testing (SVT). Above a designated cut-score signifies a 'passing' SVT performance which is likely the best indicator of valid neuropsychological test findings. Likewise, substantially below cut-point performance that nears chance or is at chance signifies invalid test performance. Significantly below chance is the sine qua non neuropsychological indicator for malingering. However, the interpretative problems with SVT performance below the cut-point yet far above chance are substantial, as pointed out in this review. This intermediate, border-zone performance on SVT measures is where substantial interpretative challenges exist. Case studies are used to highlight the many areas where additional research is needed. Historical perspectives are reviewed along with the neurobiology of effort. Reasons why performance validity testing (PVT) may be better than the SVT term are reviewed. Advances in neuroimaging techniques may be key in better understanding the meaning of border zone SVT failure. The review demonstrates the problems with rigidity in interpretation with established cut-scores. A better understanding of how certain types of neurological, neuropsychiatric and/or even test conditions may affect SVT performance is needed.

Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

International Nuclear Information System (INIS)

WANDLING, R.R.

1999-01-01

The purpose of this document is to describe tests performed to validate Revision 11.2 of the TMACS Monitor and Control System (TMCACS) and verify that the software functions as intended by design. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be talking to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab

Pain and Function Following Revision Cubital Tunnel Surgery.

Science.gov (United States)

Davidge, Kristen M; Ebersole, Gregory C; Mackinnon, Susan E

2017-11-01

The purpose of this study was to determine pain and functional outcomes following revision cubital tunnel surgery and to identify predictors of poor postoperative outcome. A retrospective cohort study was conducted of all patients undergoing revision cubital tunnel surgery over a 5-year period at a high-volume peripheral nerve center. Intraoperative findings, demographic and injury factors, and outcomes were reviewed. Average pain, worst pain, and impact of pain on self-perceived quality of life were each measured using a 10-cm visual analog scale (VAS). Function was evaluated using pinch and grip strength, as well as the Disabilities of the Arm, Shoulder and Hand (DASH) questionnaire. Differences in preoperative and postoperative pain, strength, and DASH were analyzed using nonparametric tests. Predictors of postoperative average pain were evaluated using odds ratios and linear regression analyses. The final cohort consisted of 50 patients (mean age: 46.3 ± 12.5 years; 29 [68%] male) undergoing 52 revision ulnar nerve transpositions (UNTs). Pain VAS scores decreased significantly following revision UNT. Strength and DASH scores demonstrated nonsignificant improvements postoperatively. Worse preoperative pain and greater than 1 prior cubital tunnel procedure were significant predictors of worse postoperative average pain VAS scores. Patients can and do improve following revision cubital tunnel surgery, particularly as it relates to pain. Intraoperative findings during the revision procedure suggest that adherence to specific principles in the primary operation is key to prevention of secondary cubital tunnel syndrome.

Spent fuel metal storage cask performance testing and future spent fuel concrete module performance testing

International Nuclear Information System (INIS)

McKinnon, M.A.; Creer, J.M.

1988-10-01

REA-2023 Gesellshaft fur Nuklear Service (GNS) CASTOR-V/21, Transnuclear TN-24P, and Westinghouse MC-10 metal storage casks, have been performance tested under the guidance of the Pacific Northwest Laboratory to determine their thermal and shielding performance. The REA-2023 cask was tested under Department of Energy (DOE) sponsorship at General Electric's facilities in Morris, Illinois, using BWR spent fuel from the Cooper Reactor. The other three casks were tested under a cooperative agreement between Virginia Power Company and DOE at the Idaho National Engineering Laboratory (INEL) by EGandG Idaho, Inc., using intact spent PWR fuel from the Surry reactors. The Electric Power Research Institute (EPRI) made contributions to both programs. A summary of the various cask designs and the results of the performance tests is presented. The cask designs include: solid and liquid neutron shields; lead, steel, and nodular cast iron gamma shields; stainless steel, aluminum, and copper baskets; and borated materials for criticality control. 4 refs., 8 figs., 6 tabs

Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

Energy Technology Data Exchange (ETDEWEB)

BARNES, D.A.

2000-06-01

The purpose of this document is to describe tests performed to validate Revision 12.0 of the TMACS Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be communicating to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab.

Tank Monitoring and Control System (TMACS) Acceptance Test Procedure

International Nuclear Information System (INIS)

BARNES, D.A.

2000-01-01

The purpose of this document is to describe tests performed to validate Revision 12.0 of the TMACS Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be communicating to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab

[Incorporation of an organic MAGIC (Model of Acidification of Groundwater in Catchments) and testing of the revised model using independent data sources]. [MAGIC Model

Energy Technology Data Exchange (ETDEWEB)

Sullivan, T.J.

1992-09-01

A project was initiated in March, 1992 to (1) incorporate a rigorous organic acid representation, based on empirical data and geochemical considerations, into the MAGIC model of acidification response, and (2) test the revised model using three sets of independent data. After six months of performance, the project is on schedule and the majority of the tasks outlined for Year 1 have been successfully completed. Major accomplishments to data include development of the organic acid modeling approach, using data from the Adirondack Lakes Survey Corporation (ALSC), and coupling the organic acid model with MAGIC for chemical hindcast comparisons. The incorporation of an organic acid representation into MAGIC can account for much of the discrepancy earlier observed between MAGIC hindcasts and paleolimnological reconstructions of preindustrial pH and alkalinity for 33 statistically-selected Adirondack lakes. Additional work is on-going for model calibration and testing with data from two whole-catchment artificial acidification projects. Results obtained thus far are being prepared as manuscripts for submission to the peer-reviewed scientific literature.

An in-vitro biomechanical study of different fixation techniques for the extended trochanteric osteotomy in revision THA.

Science.gov (United States)

Zhu, Zhonglin; Ding, Hui; Shao, Hongyi; Zhou, Yixin; Wang, Guangzhi

2013-04-09

The wire fixation and the cable grip fixation have been developed for the extended trochanteric osteotomy (ETO) in the revision of total hip arthroplasty (THA). Many studies reported the postoperative performance of the patients, but with little quantitative biomechanical comparison of the two fixation systems. An in-vitro testing approach was designed to record the loosening between the femoral bed and the greater trochanter after fixations. Ten cadaveric femurs were chosen in this study. Each femur underwent the THA, revision by ETO and fixations. The tension to the greater trochanter was from 0 to 500N in vertical and lateral direction, respectively. The translation and rotation of the greater trochanter with respect to the bony bed were captured by an optical tracking system. In the vertical tension tests, the overall translation of the greater trochanter was observed 0.4 mm in the cable fixations and 7.0 mm in the wire fixations. In the lateral tension tests, the overall motion of the greater trochanter was 2.0 mm and 1.2° in the cable fixations, while it was 6.2 mm and 5.3° in the wire fixations. The result was significantly different between the two fixation systems. The stability of the proximal femur after ETO using different fixations in the revision THA was investigated. The cable grip fixation was significantly more stable than the wire fixation.

Building America Performance Analysis Procedures: Revision 1

Energy Technology Data Exchange (ETDEWEB)

Hendron, R.; Anderson, R.; Judkoff, R.; Christensen, C.; Eastment, M.; Norton, P.; Reeves, P.; Hancock, E.

2004-06-01

To measure progress toward multi-year Building America research goals, cost and performance trade-offs are evaluated through a series of controlled field and laboratory experiments supported by energy analysis techniques that use test data to''calibrate'' energy simulation models. This report summarizes the guidelines for reporting such analytical results using the Building America Research Benchmark (Version 3.1) in studies that also include consideration of current Regional and Builder Standard Practice. Version 3.1 of the Benchmark is generally consistent with the 1999 Home Energy Rating System (HERS) Reference Home, with additions that allow evaluation of all home energy uses.

Midterm Clinical and Radiographic Results of Mobile-Bearing Revision Total Knee Arthroplasty.

Science.gov (United States)

Kim, Raymond H; Martin, J Ryan; Dennis, Douglas A; Yang, Charlie C; Jennings, Jason M; Lee, Gwo-Chin

2017-06-01

Constrained implants are frequently required in revision total knee arthroplasty (TKA) and are associated with an increase in aseptic component loosening and damage or wear to the constraining mechanisms, compared with primary TKA. The purpose of the following study was to evaluate the midterm clinical and radiographic results including the incidence of bearing complications in a group of patients undergoing revision TKA using mobile-bearing revision TKA implants. We retrospectively reviewed 316 consecutive mobile-bearing revision TKAs performed at 2 centers between 2006 and 2010. There were 183 women and 133 men with a mean age of 66 years. The patients were evaluated clinically using the Knee Society scores. A radiographic analysis was performed. Bearing specific complications (ie, instability or dislocation) were recorded. Patients were followed-up for a minimum of 24 months and a median of 59.88 months (range 24-121.2). The average Knee Society knee score and function scores increased from 40.8 and 47.9 points preoperatively to 80 points and 70.3 points, respectively (P bearing complications were observed. Revision TKA using mobile-bearing revision components demonstrated favorable midterm clinical and radiographic results with no occurrence of bearing instability or dislocation. Longer follow-up is required to evaluate for potential advantages of mobile-bearings over fixed-bearing revision components in terms of polyethylene wear reduction, reduced stress transmission across fixation interfaces, and reduced stress on the polyethylene post. Copyright © 2017 Elsevier Inc. All rights reserved.

Revising and editing for translators

CERN Document Server

Mossop, Brian

2014-01-01

Revising and Editing for Translators provides guidance and learning materials for translation students learning to edit texts written by others, and professional translators wishing to improve their self-revision ability or learning to revise the work of others. Editing is understood as making corrections and improvements to texts, with particular attention to tailoring them to the given readership. Revising is this same task applied to draft translations. The linguistic work of editors and revisers is related to the professional situations in which they work. Mossop offers in-depth coverage of a wide range of topics, including copyediting, style editing, structural editing, checking for consistency, revising procedures and principles, and translation quality assessment. This third edition provides extended coverage of computer aids for revisers, and of the different degrees of revision suited to different texts. The inclusion of suggested activities and exercises, numerous real-world examples, a proposed gra...

UAS Integration in the NAS Project: Integrated Test and Evaluation (IT&E) Flight Test 3. Revision E

Science.gov (United States)

Marston, Michael

2015-01-01

The desire and ability to fly Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) is of increasing urgency. The application of unmanned aircraft to perform national security, defense, scientific, and emergency management are driving the critical need for less restrictive access by UAS to the NAS. UAS represent a new capability that will provide a variety of services in the government (public) and commercial (civil) aviation sectors. The growth of this potential industry has not yet been realized due to the lack of a common understanding of what is required to safely operate UAS in the NAS. NASA's UAS Integration into the NAS Project is conducting research in the areas of Separation Assurance/Sense and Avoid Interoperability, Human Systems Integration (HSI), and Communication to support reducing the barriers of UAS access to the NAS. This research is broken into two research themes namely, UAS Integration and Test Infrastructure. UAS Integration focuses on airspace integration procedures and performance standards to enable UAS integration in the air transportation system, covering Sense and Avoid (SAA) performance standards, command and control performance standards, and human systems integration. The focus of Test Infrastructure is to enable development and validation of airspace integration procedures and performance standards, including the integrated test and evaluation. In support of the integrated test and evaluation efforts, the Project will develop an adaptable, scalable, and schedulable relevant test environment capable of evaluating concepts and technologies for unmanned aircraft systems to safely operate in the NAS. To accomplish this task, the Project will conduct a series of Human-in-the-Loop and Flight Test activities that integrate key concepts, technologies and/or procedures in a relevant air traffic environment. Each of the integrated events will build on the technical achievements, fidelity and complexity of the previous tests and

10 CFR 26.168 - Blind performance testing.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Blind performance testing. 26.168 Section 26.168 Energy... and Human Services § 26.168 Blind performance testing. (a) Each licensee and other entity shall submit blind performance test samples to the HHS-certified laboratory. (1) During the initial 90-day period of...

Smoking is associated with earlier time to revision of total knee arthroplasty.

Science.gov (United States)

Lim, Chin Tat; Goodman, Stuart B; Huddleston, James I; Harris, Alex H S; Bhowmick, Subhrojyoti; Maloney, William J; Amanatullah, Derek F

2017-10-01

Smoking is associated with early postoperative complications, increased length of hospital stay, and an increased risk of revision after total knee arthroplasty (TKA). However, the effect of smoking on time to revision TKA is unknown. A total of 619 primary TKAs referred to an academic tertiary center for revision TKA were retrospectively stratified according to the patient smoking status. Smoking status was then analyzed for associations with time to revision TKA using a Chi square test. The association was also analyzed according to the indication for revision TKA. Smokers (37/41, 90%) have an increased risk of earlier revision for any reason compared to non-smokers (274/357, 77%, p=0.031). Smokers (37/41, 90%) have an increased risk of earlier revision for any reason compared to ex-smokers (168/221, 76%, p=0.028). Subgroup analysis did not reveal a difference in indication for revision TKA (p>0.05). Smokers are at increased risk of earlier revision TKA when compared to non-smokers and ex-smokers. The risk for ex-smokers was similar to that of non-smokers. Smoking appears to have an all-or-none effect on earlier revision TKA as patients who smoked more did not have higher risk of early revision TKA. These results highlight the need for clinicians to urge patients not to begin smoking and encourage smokers to quit smoking prior to primary TKA. Copyright © 2017 Elsevier B.V. All rights reserved.

Loosening After Acetabular Revision

DEFF Research Database (Denmark)

Beckmann, Nicholas A.; Weiss, Stefan; Klotz, Matthias C.M.

2014-01-01

The best method of revision acetabular arthroplasty remains unclear. Consequently, we reviewed the literature on the treatment of revision acetabular arthroplasty using revision rings (1541 cases; mean follow-up (FU) 5.7 years) and Trabecular Metal, or TM, implants (1959 cases; mean FU 3.7 years...

Underground test area subproject waste management plan. Revision No. 1

International Nuclear Information System (INIS)

1996-08-01

The Nevada Test Site (NTS), located in southern Nevada, was the site of 928 underground nuclear tests conducted between 1951 and 1992. The tests were performed as part of the Atomic Energy Commission and U.S. Department of Energy (DOE) nuclear weapons testing program. The NTS is managed by the DOE Nevada Operations Office (DOE/NV). Of the 928 tests conducted below ground surface at the NTS, approximately 200 were detonated below the water table. As an unavoidable consequence of these testing activities, radionuclides have been introduced into the subsurface environment, impacting groundwater. In the few instances of groundwater sampling, radionuclides have been detected in the groundwater; however, only a very limited investigation of the underground test sites and associated shot cavities has been conducted to date. The Underground Test Area (UGTA) Subproject was established to fill this void and to characterize the risk posed to human health and the environment as a result of underground nuclear testing activities at the NTS. One of its primary objectives is to gather data to characterize the deep aquifer underlying the NTS

Revision hip preservation surgery with hip arthroscopy: clinical outcomes.

Science.gov (United States)

Domb, Benjamin G; Stake, Christine E; Lindner, Dror; El-Bitar, Youseff; Jackson, Timothy J

2014-05-01

To analyze and report the clinical outcomes of a cohort of patients who underwent revision hip preservation with arthroscopy and determine predictors of positive and negative outcomes. During the study period from April 2008 to December 2010, all patients who underwent revision hip preservation with arthroscopy were included. This included patients who had previous open surgery and underwent revision with arthroscopy. Patient-reported outcome (PRO) scores were obtained preoperatively and at 3-month, 1-year, 2-year, and 3-year follow-up time points. Any revision surgeries and conversions to total hip arthroplasty were noted. A multiple regression analysis was performed to look for positive and negative predictive factors for improvement in PROs after revision hip arthroscopy. Forty-seven hips in 43 patients had completed 2 years' follow-up or needed total hip arthroplasty. The mean length of follow-up was 29 months (range, 24 to 47 months). Of the hips, 31 (66%) had either unaddressed or incompletely treated femoroacetabular impingement. There was a significant improvement in all PRO scores at a mean of 29 months after revision (P arthroscopy can achieve moderately successful outcomes and remains a viable treatment strategy after failed primary hip preservation surgery. Preoperative predictors of success after revision hip arthroscopy include segmental labral defects, unaddressed or incompletely addressed femoroacetabular impingement, heterotopic ossification, and previous open surgery. Level IV, therapeutic case series. Copyright © 2014 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Performance Testing of Cutting Fluids

DEFF Research Database (Denmark)

Belluco, Walter

The importance of cutting fluid performance testing has increased with documentation requirements of new cutting fluid formulations based on more sustainable products, as well as cutting with minimum quantity of lubrication and dry cutting. Two sub-problems have to be solved: i) which machining...... tests feature repeatability, reproducibility and sensitivity to cutting fluids, and ii) to what extent results of one test ensure relevance to a wider set of machining situations. The present work is aimed at assessing the range of validity of the different testing methods, investigating correlation...... within the whole range of operations, materials, cutting fluids, operating conditions, etc. Cutting fluid performance was evaluated in turning, drilling, reaming and tapping, and with respect to tool life, cutting forces, chip formation and product quality (dimensional accuracy and surface integrity...

Revised Reynolds Stress and Triple Product Models

Science.gov (United States)

Olsen, Michael E.; Lillard, Randolph P.

2017-01-01

Revised versions of Lag methodology Reynolds-stress and triple product models are applied to accepted test cases to assess the improvement, or lack thereof, in the prediction capability of the models. The Bachalo-Johnson bump flow is shown as an example for this abstract submission.

Trends in Revision Elbow Ulnar Collateral Ligament Reconstruction in Professional Baseball Pitchers.

Science.gov (United States)

Wilson, Alexander T; Pidgeon, Tyler S; Morrell, Nathan T; DaSilva, Manuel F

2015-11-01

To determine the frequency of revision elbow ulnar collateral ligament (UCL) reconstruction in professional baseball pitchers. Data were collected on 271 professional baseball pitchers who underwent primary UCL reconstruction. Each player was evaluated retrospectively for occurrence of revision UCL reconstructive surgery to treat failed primary reconstruction. Data on players who underwent revision UCL reconstruction were compiled to determine total surgical revision incidence and revision rate by year. The incidence of early revision was analyzed for trends. Average career length after primary UCL reconstruction was calculated and compared with that of players who underwent revision surgery. Logistic regression analysis was performed to assess risk factors for revision including handedness, pitching role, and age at the time of primary reconstruction. Between 1974 and 2014, the annual incidence of primary UCL reconstructions among professional pitchers increased, while the proportion of cases being revised per year decreased. Of the 271 pitchers included in the study, 40 (15%) required at least 1 revision procedure during their playing career. Three cases required a second UCL revision reconstruction. The average time from primary surgery to revision was 5.2 ± 3.2 years (range, 1-13 years). The average length of career following primary reconstruction for all players was 4.9 ± 4.3 years (range, 0-22 years). The average length of career following revision UCL reconstruction was 2.5 ± 2.4 years (range, 0-8 years). No risk factors for needing revision UCL reconstruction were identified. The incidence of primary UCL reconstructions among professional pitchers is increasing; however, the rate of primary reconstructions requiring revision is decreasing. Explanations for the decreased revision rate may include improved surgical technique and improved rehabilitation protocols. Therapeutic IV. Copyright © 2015 American Society for Surgery of the Hand. Published by

REVISED STREAM CODE AND WASP5 BENCHMARK

International Nuclear Information System (INIS)

Chen, K

2005-01-01

STREAM is an emergency response code that predicts downstream pollutant concentrations for releases from the SRS area to the Savannah River. The STREAM code uses an algebraic equation to approximate the solution of the one dimensional advective transport differential equation. This approach generates spurious oscillations in the concentration profile when modeling long duration releases. To improve the capability of the STREAM code to model long-term releases, its calculation module was replaced by the WASP5 code. WASP5 is a US EPA water quality analysis program that simulates one-dimensional pollutant transport through surface water. Test cases were performed to compare the revised version of STREAM with the existing version. For continuous releases, results predicted by the revised STREAM code agree with physical expectations. The WASP5 code was benchmarked with the US EPA 1990 and 1991 dye tracer studies, in which the transport of the dye was measured from its release at the New Savannah Bluff Lock and Dam downstream to Savannah. The peak concentrations predicted by the WASP5 agreed with the measurements within ±20.0%. The transport times of the dye concentration peak predicted by the WASP5 agreed with the measurements within ±3.6%. These benchmarking results demonstrate that STREAM should be capable of accurately modeling releases from SRS outfalls

The threshold force required for femoral impaction grafting in revision hip surgery.

LENUS (Irish Health Repository)

Flannery, Olivia M

2010-06-01

BACKGROUND AND PURPOSE: Femoral impaction grafting requires vigorous impaction to obtain adequate stability without risk of fracture, but the force of impaction has not been determined. We determined this threshold force in a preliminary study using animal femurs. METHODS: Adult sow femurs were used because of their morphological similarity to human femurs in revision hip arthroplasty. 35 sow femurs were impacted with morselized bone chips and an increasing force was applied until the femur fractured. This allowed a threshold force to be established. 5 other femurs were impacted to this force and an Exeter stem was cemented into the neomedullary canal. A 28-mm Exeter head was attached and loaded by direct contact with a hydraulic testing machine. Axial cyclic loading was performed and the position sensor of the hydraulic testing machine measured the prosthetic head subsidence. RESULTS: 29 tests were completed successfully. The threshold force was found to be 4 kN. There was no statistically significant correlation between the load at fracture and the cortex-to-canal ratio or the bone mineral density. Following impaction with a maximum force of 4 kN, the average axial subsidence was 0.28 mm. INTERPRETATION: We achieved a stable construct without fracture. Further studies using human cadaveric femurs should be done to determine the threshold force required for femoral impaction grafting in revision hip surgery.

The Revised Animal Preference Test: An Implicit Probe of Tendencies Toward Psychopathy.

Science.gov (United States)

Penzel, Ian B; Bair, Jessica; Liu, Tianwei; Robinson, Michael D

2018-05-01

At least some forms of interpersonal violence could follow from a vision of the self as a fierce, dominant creature. This should be particularly true when psychopathic (more proactive, less reactive) tendencies are involved. Possible relations of this type were examined in two studies (total N = 278) in which college student samples were presented with a new, structured version of an old projective test typically used in psychotherapy contexts. Participants were presented with predator-prey animal pairs (e.g., lion-zebra) that were not explicitly labeled as such. For each pair, the person was asked to choose the animal that they would more prefer to be. Participants who desired to be predator animals more often, on this Revised Animal Preference Test (RAPT), tended toward psychopathy to a greater extent. In Study 1, such relations were manifest in terms of correlations with psychopathic traits and with an interpersonal style marked by hostile dominance. Further analyses, though, revealed that predator self-identifications were more strongly related to primary psychopathy than secondary psychopathy. Study 2 replicated the interpersonal style correlates of the RAPT. In addition, photographs were taken of the participants in the second study and these photographs were rated for apparent hostility and dominance. As hypothesized, participants who wanted to be predator animals to a greater extent also appeared more hostile and dominant in their nonverbal behaviors. These studies suggest that projective preferences can be assessed in a reliable manner through the use of standardizing procedures. Furthermore, the studies point to some of the motivational factors that may contribute to psychopathy and interpersonal violence.

Improving Hearing Aid Self-Efficacy and Utility Through Revising a Hearing Aid User Guide: A Pilot Study.

Science.gov (United States)

McMullan, Alexandra; Kelly-Campbell, Rebecca J; Wise, Kim

2018-03-08

This pilot study aimed to investigate whether revising a hearing aid user guide (HAUG) is associated with improved hearing aid self-efficacy and utility performance. In Part 1, an HAUG was evaluated using the Suitability Assessment of Material (SAM) and readability formulas (Flesch Reading Ease [Flesch, 1943], Flesch-Kincaid Readability Formula [Kincaid, Fishburne, Rogers, & Chissom, 1957], and Simple Measure of Gobbledygook [McLaughlin, 1969]). The HAUG was revised using results from the SAM and best practice guidelines. The revision included generating a video. In Part 2, 30 adults with hearing impairment were randomly assigned to use either the original guide (N = 15) or the revised guide and video (N = 15) to perform a utility task. Participants' self-efficacy was measured using the Basic and Advanced Handling subscales of the Measure of Audiologic Rehabilitation Self-Efficacy for Hearing Aids questionnaire. SAM and readability were compared between the original and revised guides (Doak, Doak, & Root, 1996). SAM and readability were improved following the revision. Participants in the revised guide group performed significantly better on the utility task and on the Measure of Audiologic Rehabilitation Self-Efficacy for Hearing Aids subscales than participants in the original guide group. These results are encouraging as they indicate that there is scope to influence self-efficacy and utility performance through the use of appropriate HAUGs.

Containment leakage rate testing requirements

International Nuclear Information System (INIS)

Arndt, E.G.

1992-01-01

This report presents the status of several documents under revision or development that provide requirements and guidance for testing nuclear power plant containment systems for leakage rates. These documents include the general revision to 10 CFR Part 50, Appendix J; the regulatory guide affiliated with the revision to Appendix J; the national standard that the regulatory guide endorses, ANSI/ANS-56.8, 'Containment System Leakage Rate Testing Requirements'; and the draft industry Licensing Topical Report, 'Standardized Program for Primary Containment Integrity Testing'. The actual or potential relationships between these documents are also explored

Descriptive epidemiology of the Multicenter ACL Revision Study (MARS) cohort.

Science.gov (United States)

Wright, Rick W; Huston, Laura J; Spindler, Kurt P; Dunn, Warren R; Haas, Amanda K; Allen, Christina R; Cooper, Daniel E; DeBerardino, Thomas M; Lantz, Brett Brick A; Mann, Barton J; Stuart, Michael J

2010-10-01

Revision anterior cruciate ligament (ACL) reconstruction has worse outcomes than primary reconstructions. Predictors for these worse outcomes are not known. The Multicenter ACL Revision Study (MARS) Group was developed to perform a multisurgeon, multicenter prospective longitudinal study to obtain sufficient subjects to allow multivariable analysis to determine predictors of clinical outcome. To describe the formation of MARS and provide descriptive analysis of patient demographics and clinical features for the initial 460 enrolled patients to date in this prospective cohort. Cross-sectional study; Level of evidence, 2. After training and institutional review board approval, surgeons began enrolling patients undergoing revision ACL reconstruction, recording patient demographics, previous ACL reconstruction methods, intra-articular injuries, and current revision techniques. Enrolled subjects completed a questionnaire consisting of validated patient-based outcome measures. As of April 1, 2009, 87 surgeons have enrolled a total of 460 patients (57% men; median age, 26 years). For 89%, the reconstruction was the first revision. Mode of failure as deemed by the revising surgeon was traumatic (32%), technical (24%), biologic (7%), combination (37%), infection (MARS Group has been able to quickly accumulate the largest revision ACL reconstruction cohort reported to date. Traumatic reinjury is deemed by surgeons to be the most common single mode of failure, but a combination of factors represents the most common mode of failure. Allograft graft choice is more common in the revision setting than autograft. Concomitant knee injury is extremely common in this population.

Composite Reliability and Standard Errors of Measurement for a Seven-Subtest Short Form of the Wechsler Adult Intelligence Scale-Revised.

Science.gov (United States)

Schretlen, David; And Others

1994-01-01

Composite reliability and standard errors of measurement were computed for prorated Verbal, Performance, and Full-Scale intelligence quotient (IQ) scores from a seven-subtest short form of the Wechsler Adult Intelligence Scale-Revised. Results with 1,880 adults (standardization sample) indicate that this form is as reliable as the complete test.…

Heater test planning for the near surface test facility at the Hanford reservation

International Nuclear Information System (INIS)

DuBois, A.; Binnall, E.; Chan, T.; McEvoy, M.; Nelson, P.; Remer, J.

1979-03-01

The underground test facility NSTF being constructed at Gable Mountain, is the site for a group of experiments designed to evaluate the thermo-mechanical suitability of a deep basalt stratum as a permanent repository for nuclear waste. Thermo-mechanical modeling was performed to help design the instrumentation arrays for the three proposed heater tests (two full scale tests and one time scale test) and predict the thermal environment of the heaters and instruments. The modeling does not reflect recent RHO revisions to the in situ heater experiment plan. Heaters, instrumentation, and data acquisition system designs and recommendations were adapted from those used in Sweden

Testing of Type A and B packages in accordance with IAEA transport regulations

International Nuclear Information System (INIS)

Nitsche, F.; Runge, K.; Birkigt, W.; Mueller, E.

1984-01-01

Revised and extended version of a paper presented during the Interregional Training Course on the Safe Transport of Radioactive Materials, organized by the IAEA, Harwell, May 1982, dealing with the test conditions for Type A and Type B packages as well as possible test methods, the performance of testing, and the assessmnt of test results

Test Scatter on the WISC-R in Learning Disabled Children.

Science.gov (United States)

Tabachnick, Barbara Gerson

Scatter on the revised Wechsler Intelligence Scale for children (WISC-R) was evaluated for 105 learning disabled (LD) children. Scatter was defined as range of scaled scores on: (1) five regular verbal tests; (2) five regular performance tests; and (3) all 10 regular subtests. Pairwise combinations of 11 subtests were also evaluated for deviations…

Revision washout decreases implant capsule tissue culture positivity: a multicenter study.

Science.gov (United States)

Henry, Gerard D; Carson, Culley C; Wilson, Steven K; Wiygul, Jeremy; Tornehl, Chris; Cleves, Mario A; Simmons, Caroline J; Donatucci, Craig F

2008-01-01

Positive cultures, visible biofilm and confocal micrography confirm bacterial presence on clinically uninfected inflatable penile prostheses at revision surgery. Salvage irrigation has been proved to rescue patients with clinically infected inflatable penile prostheses. Similar washout at revision for noninfectious reasons significantly lowers subsequent infection rates. We investigated a larger series of patients for positive culture rates and evaluated implant capsule tissue culture rates before and after revision washout. At 4 institutions a total of 148 patients with inflatable penile prostheses underwent revision surgery for noninfectious reasons between June 2001 and September 2005. Swab cultures of the fluid around the pump and visible biofilm were obtained. Also, in 65 patients a wedge of tissue from the capsule that forms around the pump was cultured. After implant removal revision washout of the implant spaces was performed and a second wedge of tissue was cultured. Of the 148 patients 97 (66%) had positive bacterial swab cultures of the fluid around the pump or biofilm. A total of 124 isolates were cultured. Of the 65 implant capsule tissue cultures obtained before washout 28 (43%) were positive for bacteria, while 16 (25%) obtained after revision washout were positive. Positive cultures and visible bacterial biofilm are present on clinically uninfected inflatable penile prostheses at revision surgery in most patients. Revision washout appears to decrease the bacterial load on implant capsule tissue at revision surgery of inflatable penile prostheses for noninfectious reasons.

Item response theory analysis of the life orientation test-revised: age and gender differential item functioning analyses.

Science.gov (United States)

Steca, Patrizia; Monzani, Dario; Greco, Andrea; Chiesi, Francesca; Primi, Caterina

2015-06-01

This study is aimed at testing the measurement properties of the Life Orientation Test-Revised (LOT-R) for the assessment of dispositional optimism by employing item response theory (IRT) analyses. The LOT-R was administered to a large sample of 2,862 Italian adults. First, confirmatory factor analyses demonstrated the theoretical conceptualization of the construct measured by the LOT-R as a single bipolar dimension. Subsequently, IRT analyses for polytomous, ordered response category data were applied to investigate the items' properties. The equivalence of the items across gender and age was assessed by analyzing differential item functioning. Discrimination and severity parameters indicated that all items were able to distinguish people with different levels of optimism and adequately covered the spectrum of the latent trait. Additionally, the LOT-R appears to be gender invariant and, with minor exceptions, age invariant. Results provided evidence that the LOT-R is a reliable and valid measure of dispositional optimism. © The Author(s) 2014.

Test plan for Tank 241-AW-101 solubility screening tests

International Nuclear Information System (INIS)

Person, J.C.

1998-01-01

Tank 241-AW-101 (101-AW) has been identified as one of the early tanks to be for retrieved for low level waste pretreatment and immobilization and retrieval of the tank waste may require dilution. This test is to determine the effects of dilution on the mass of solids and their composition. This test plan gives test instructions, example data sheets, a waste compatibility review, and a waste stream fact sheet. This test Plan is similar to tests on tanks 241-AN-102 (Person 1998a) and 241-AN-107 (Person 1998 b). The 101-AW tests will be done with composites of liquid and solids from grab samples that were taken in 1998 (Benar 1998). Future revisions of the Tank Sampling and Analysis Plan (Benar 1998) may change the details of the work performed under this test plan

Impact of applying the more stringent validation criteria of the revised European Society of Hypertension International Protocol 2010 on earlier validation studies.

Science.gov (United States)

Stergiou, George S; Karpettas, Nikos; Atkins, Neil; O'Brien, Eoin

2011-04-01

Since 2002 when the European Society of Hypertension International Protocol (ESH-IP) was published it has become the preferred protocol for validating blood pressure monitors worldwide. In 2010, a revised version of the ESH-IP with more stringent criteria was published. This study assesses the impact of applying the revised ESH-IP criteria. A systematic literature review of ESH-IP studies reported between 2002 and 2010 was conducted. The impact of applying the ESH-IP 2010 criteria retrospectively on the data reported in these studies was investigated. The performance of the oscillometric devices in the last decade was also investigated on the basis of the ESH-IP criteria. Among 119 published studies, 112 with sufficient data were analyzed. According to ESH-IP 2002, the test device failed in 19 studies, whereas by applying the ESH-IP 2010 criteria in 28 additional studies increased the failure rate from 17 to 42%. Of these 28 studies, in 20 (71%) the test device failed at part 1 (accuracy per measurement) and in 22 (79%) at part 2 (accuracy per subject). Most of the failures involved the '5 mmHg or less' criterion. In the last decade there has been a consistent trend toward improved performance of oscillometric devices assessed on the basis of the ESH-IP criteria. This retrospective analysis shows that the stricter revised ESH-IP 2010 criteria will noticeably increase the failure rate of devices being validated. Oscillometric devices are becoming more accurate, and the revised ESH-IP by acknowledging this trend will allow more accurate devices to enter the market.

Nuclear material control and accountancy planning and performance testing

International Nuclear Information System (INIS)

Mike Enhinger; Dennis Wilkey; Rod Martin; Ken Byers; Brian Smith

1999-01-01

An overview of performance testing as used at U.S. Department of Energy facilities is provided. Performance tests are performed on specific aspects of the regulations or site policy. The key issues in establishing a performance testing program are: identifying what needs to be tested; determining how to test; establishing criteria to evaluate test results. The program elements of performance testing program consist of: planning; coordination; conduct; evaluation. A performance test may be conducted of personnel or equipment. The DOE orders for nuclear material control and accountancy are divided into three functional areas: program administration, material accounting, and material control. Examples performance tests may be conducted on program administration, accounting, measurement and measurement control, inventory, and containment [ru

Memory-for-Designs, Bender-Gestalt, Trail Making Test, and WISC-R Performance of Retarded and Adequate Readers

Science.gov (United States)

McManis, Donald L.; And Others

1978-01-01

Twelve reading-disabled and 12 nondisabled boys, of average intellectual ability, in Grades 3 to 6 were compared on the Memory-For-Designs, Bender-Gestalt, Trail Making Test, and the 11 subtests of the Wechsler Intelligence Scale for Children--Revised (WISC-R). (Author)

Test Plan Addendum No. 1: Waste Isolation Pilot Plant bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.; Lappin, A.R.

1990-12-01

This document is the first major revision to the Test Plan: WIPP Bin-Scale CH TRU Waste Tests. Factors that make this revision necessary are described and justified in Section 1, and elaborated upon in Section 4. This addendum contains recommended estimates of, and details for: (1) The total separation of waste leaching/solubility tests from bin-scale gas tests, including preliminary details and quantities of leaching tests required for testing of Levels 1, 2, and 3 WIPP CH TRU wastes; (2) An initial description and quantification of bin-scale gas test Phase 0, added to provide a crucial tie to pretest waste characterization representatives and overall test statistical validation; (3) A revision to the number of test bins required for Phases 1 and 2 of the bin gas test program, and specification of the numbers of additional bin tests required for incorporating gas testing of Level 2 wastes into test Phase 3. Contingencies are stated for the total number of test bins required, both positive and negative, including the supporting assumptions, logic, and decision points. (4) Several other general test detail updates occurring since the Test Plan was approved and published in January, 1990. Possible impacts of recommended revisions included in this Addendum on WIPP site operations are called out and described. 56 refs., 12 tabs

Revising Lecture Notes: How Revision, Pauses, and Partners Affect Note Taking and Achievement

Science.gov (United States)

Luo, Linlin; Kiewra, Kenneth A.; Samuelson, Lydia

2016-01-01

Note taking has been categorized as a two-stage process: the recording of notes and the review of notes. We contend that note taking might best involve a three-stage process where the missing stage is revision. This study investigated the benefits of revising lecture notes and addressed two questions: First, is revision more effective than…

Difference in clinical outcome between total shoulder arthroplasty and reverse shoulder arthroplasty used in hemiarthroplasty revision surgery

NARCIS (Netherlands)

Hartel, B.P.; Alta, T.D.; Sewnath, M.E.; Willems, W.J.H.

2015-01-01

INTRODUCTION: The increase of shoulder replacements will lead to a higher revision rate of shoulder arthroplasties. The aim of this study is to evaluate the clinical results of revision surgery performed in our hospital, distinguish the differences in clinical outcome according to revision

Methods for implementing revisions to emergency operating procedures. Final report

International Nuclear Information System (INIS)

Myers, L.B.; Bell, A.J.

1984-05-01

In response to the Three Mile Island (TMI) accident, the US Nuclear Regulatory Commission (NRC) has published the TMI Action Plan. The TMI Action Plan Item I.C.1 called for the upgrading of Emergency Operating Procedures (EOPs) at nuclear power plants. The program developed from this Action Plan item has resulted in utility efforts to: (1) revise EOPs; (2) train personnel in the use of the EOPs; and (3) implement the revised EOPs. The NRC supported the study presented in this report to identify factors which influence the effectiveness of training and implementation of revised EOPs. The NRC's major concern was the possible effects of negative transfer of training. The report includes a summary of existing methods for implementing revisions to procedures based on interviews of plant personnel, a review of the training literature applicable to the effect of previously learned procedures on the learning of and performance with revised procedures (i.e., negative transfer) and recommendations of methods and schedules for implementing revised EOPs. While the study found that the concern over negative transfer of training was not as great as anticipated, several recommendations were made. These include: (1) overtraining of operators to reduce the effect of observed negative transfer; and (2) implementation of the revised EOPs as soon as possible after training to minimize the time operators must rely upon the old EOPs after having been trained on the revised EOPs. The results of the study should be useful both to the utilities and the NRC in the development and review of EOP implementation programs

The Impacts of Implementation Accounting Standard PSAK No. 24 (Revision 2004 on Post Employment Benefit Towards Company’s Performance

Directory of Open Access Journals (Sweden)

Elfrida Yanti

2011-11-01

Full Text Available Financial analysis is useful for all company to measure their performance and expected to show improvement result in order to determine the company’s condition. . Financial ratios are tools to help anticipate the future conditions and to predict some actions or strategies that will useful in improving the company’s future performance, which is from evaluating the previous financial statement. Using financial ratios this research tries to impose one indicator, post employment benefit and how it would impact company financial performance. PT. ABC Will be the object case which implementation the post employment benefit based on particular regulation PSAK No. 24 (revision 2004. The researcher would like to focuses on the profitability ratios by Return on Asset ratio (ROA, liquidity ratio by Current Ratio (CR and the leverage ratio by Debt-Equity ratio. 

Common Variance Among Three Measures of Nonverbal Cognitive Ability: WISC-R Performance Scale, WJPB-TCA Reasoning Cluster, and Halstead Category Test.

Science.gov (United States)

Telzrow, Cathy F.; Harr, Gale A.

1987-01-01

Examined the relationships among two psychometric measures of nonverbal cognitive ability - The Wechsler Intelligence Scale for Children-Revised (WISC-R) and the Woodcock-Johnson Psychoeducational Battery-Tests of Cognitive Ability (WJPB-TCA) and a neuropsychological test of abstract reasoning and concept formation (Halstead Category Test) in 25…

MITG post-test analysis and design improvements

International Nuclear Information System (INIS)

Schock, A.

1983-01-01

The design, performance analysis, and key attributes of the Modular Isotopic Thermoelectric Generator (MITG) were described in a 1981 IECEC paper; and the design, fabrication, and testing of prototypical MITG test assemblies were described in preceding papers in these proceedings. Each test assembly simulated a typical modular slice of the flight generator. The present paper describes a detailed thermal-stress analysis, which identified the causes of stress-related problems observed during the tests. It then describes how additional analyses were used to evaluate design changes to alleviate those problems. Additional design improvements are discussed in the next paper in these proceedings, which also describes revised fabrication procedures and updated performance estimates for the generator

Postoperative pain outcomes after transvaginal mesh revision.

Science.gov (United States)

Danford, Jill M; Osborn, David J; Reynolds, W Stuart; Biller, Daniel H; Dmochowski, Roger R

2015-01-01

Although the current literature discusses mesh complications including pain, as well as suggesting different techniques for removing mesh, there is little literature regarding pain outcomes after surgical removal or revision. The purpose of this study is to determine if surgical removal or revision of vaginal mesh improves patient's subjective complaints of pelvic pain associated with original placement of mesh. After obtaining approval from the Vanderbilt University Medical Center Institutional Review Board, a retrospective review of female patients with pain secondary to previous mesh placement who underwent excision or revision of vaginal mesh from January 2000 to August 2012 was performed. Patient age, relevant medical history including menopause status, previous hysterectomy, smoking status, and presence of diabetes, fibromyalgia, interstitial cystitis, and chronic pelvic pain, was obtained. Patients' postoperative pain complaints were assessed. Of the 481 patients who underwent surgery for mesh revision, removal or urethrolysis, 233 patients met our inclusion criteria. One hundred and sixty-nine patients (73 %) reported that their pain improved, 19 (8 %) reported that their pain worsened, and 45 (19 %) reported that their pain remained unchanged after surgery. Prior history of chronic pelvic pain was associated with increased risk of failure of the procedure to relieve pain (OR 0.28, 95 % CI 0.12-0.64, p = 0.003). Excision or revision of vaginal mesh appears to be effective in improving patients' pain symptoms most of the time. Patients with a history of chronic pelvic pain are at an increased risk of no improvement or of worsening pain.

INDIRECT WRITTEN CORRECTIVE FEEDBACK, REVISION, AND LEARNING

Directory of Open Access Journals (Sweden)

Fatemeh Poorebrahim

2017-01-01

Full Text Available Corrective feedback, the necessity of providing it, and how it should be provided has been one of the hot topics in the area of ELT. Amid continuing controversies over whether providing feedback helps L2 learners improve their writing accuracy, many research studies have been undertaken to compare the relative effectiveness of different types of feedback. However, the difference between two types of indirect corrective feedback, namely indication and indication plus location, have not been properly examined yet. Motivated to narrow this gap, this study is designed to compare two groups of Iranian learners, each revising their papers based on one of the aforementioned options. For data analysis, a series of independent samples t tests were employed. The results revealed that the difference between the two groups in their reduction of errors from the original draft to the revision of each task followed a growing trend and became significant. Nonetheless, the difference in accuracy of new pieces of writing fell short of significance. Finally, it was found that error reduction in revision stage cannot be considered as learning. The results of the study, discussed in relation to that of others, implicate that the purpose for which feedback is provided is essential in determining the type of feedback; more explicit feedback is better for revising purposes while more implicit feedback is good for learning purposes.

Working Memory and the Revision of Syntactic and Discourse Ambiguities

Science.gov (United States)

Evans, William S.; Caplan, David; Ostrowski, Adam; Michaud, Jennifer; Guarino, Anthony; Waters, Gloria

2015-01-01

Two hundred participants, 50 in each of four age ranges (19 – 29; 30 – 49, 50 – 69, 70 – 90) were tested for short term working memory, speed of processing and on-line processing of three types of sentences in which an initially assigned syntactic structure and/or semantic interpretation had to be revised. Self-paced reading times were longer for the segments which signaled the need for revision, and there were interactions of age and sentence type and of speed of processing and sentence type, but not of working memory and sentence type, on reading times for these segments. The results provide evidence that working memory does not support the processes that revise the structure and interpretation of sentences and discourse. PMID:25485458

Validation testing of safety-critical software

International Nuclear Information System (INIS)

Kim, Hang Bae; Han, Jae Bok

1995-01-01

A software engineering process has been developed for the design of safety critical software for Wolsung 2/3/4 project to satisfy the requirements of the regulatory body. Among the process, this paper described the detail process of validation testing performed to ensure that the software with its hardware, developed by the design group, satisfies the requirements of the functional specification prepared by the independent functional group. To perform the tests, test facility and test software were developed and actual safety system computer was connected. Three kinds of test cases, i.e., functional test, performance test and self-check test, were programmed and run to verify each functional specifications. Test failures were feedback to the design group to revise the software and test results were analyzed and documented in the report to submit to the regulatory body. The test methodology and procedure were very efficient and satisfactory to perform the systematic and automatic test. The test results were also acceptable and successful to verify the software acts as specified in the program functional specification. This methodology can be applied to the validation of other safety-critical software. 2 figs., 2 tabs., 14 refs. (Author)

The mechanical effect of the existing cement mantle on the in-cement femoral revision.

LENUS (Irish Health Repository)

Keeling, Parnell

2012-08-01

Cement-in-cement revision hip arthroplasty is an increasingly popular technique to replace a loose femoral stem which retains much of the original cement mantle. However, some concern exists regarding the retention of the existing fatigued and aged cement in such cement-in-cement revisions. This study investigates whether leaving an existing fatigued and aged cement mantle degrades the mechanical performance of a cement-in-cement revision construct.

NRC valve performance test program - check valve testing

International Nuclear Information System (INIS)

Jeanmougin, N.M.

1987-01-01

The Valve Performance Test Program addresses the current requirements for testing of pressure isolation valves (PIVs) in light water reactors. Leak rate monitoring is the current method used by operating commercial power plants to survey the condition of their PIVs. ETEC testing of three check valves (4-inch, 6-inch, and 12-inch nominal diameters) indicates that leak rate testing is not a reliable method for detecting impending valve failure. Acoustic emission monitoring of check valves shows promise as a method of detecting loosened internals damage. Future efforts will focus on evaluation of acoustic emission monitoring as a technique for determining check valve condition. Three gate valves also will be tested to evaluate whether the check valve results are applicable to gate type PIVs

Acetabular Cup Revision.

Science.gov (United States)

Kim, Young-Ho

2017-09-01

The use of acetabular cup revision arthroplasty is on the rise as demands for total hip arthroplasty, improved life expectancies, and the need for individual activity increase. For an acetabular cup revision to be successful, the cup should gain stable fixation within the remaining supportive bone of the acetabulum. Since the patient's remaining supportive acetabular bone stock plays an important role in the success of revision, accurate classification of the degree of acetabular bone defect is necessary. The Paprosky classification system is most commonly used when determining the location and degree of acetabular bone loss. Common treatment options include: acetabular liner exchange, high hip center, oblong cup, trabecular metal cup with augment, bipolar cup, bulk structural graft, cemented cup, uncemented cup including jumbo cup, acetabular reinforcement device (cage), trabecular metal cup cage. The optimal treatment option is dependent upon the degree of the discontinuity, the amount of available bone stock and the likelihood of achieving stable fixation upon supportive host bone. To achieve successful acetabular cup revision, accurate evaluation of bone defect preoperatively and intraoperatively, proper choice of method of acetabular revision according to the evaluation of acetabular bone deficiency, proper technique to get primary stability of implant such as precise grafting technique, and stable fixation of implant are mandatory.

Revised design for the Tokamak experimental power reactor

International Nuclear Information System (INIS)

Stacey, W.M. Jr.; Abdou, M.A.; Brooks, J.N.

1977-03-01

A new, preliminary design has been identified for the tokamak experimental power reactor (EPR). The revised EPR design is simpler, more compact, less expensive and has somewhat better performance characteristics than the previous design, yet retains many of the previously developed design concepts. This report summarizes the principle features of the new EPR design, including performance and cost

Wind turbine power performance verification in complex terrain and wind farms

DEFF Research Database (Denmark)

Friis Pedersen, Troels; Gjerding, S.; Enevoldsen, P.

2002-01-01

is a power performance verification procedure for individual wind turbines. The third is a power performance measurement procedure of whole wind farms, and the fourth is a power performance measurement procedurefor non-grid (small) wind turbines. This report presents work that was made to support the basis......The IEC/EN 61400-12 Ed 1 standard for wind turbine power performance testing is being revised. The standard will be divided into four documents. The first one of these is more or less a revision of the existing document on power performance measurementson individual wind turbines. The second one...... then been investigated in more detail. The work has given rise to a range of conclusionsand recommendations regarding: guaranties on power curves in complex terrain; investors and bankers experience with verification of power curves; power performance in relation to regional correction curves for Denmark...

Evaluations of 1990 PRISM design revisions

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Slovik, G.C.; Chan, B.C.; Aronson, A.L.; Kennett, R.J.

1992-03-01

Analyses of the 1990 version of the PRISM Advanced Liquid Metal Reactor (ALMR) design are presented and discussed. Most of the calculations were performed using BNL computer codes, particularly SSC and MINET. In many cases, independent BNL calculations were compared against analyses presented by General Electric when they submitted the PRISM design revisions for evaluation by the Nuclear Regulatory Commission (NRC). The current PRISM design utilizes the metallic fuel developed by Argonne National Laboratory (ANL) which facilitates the passive/''inherent'' shutdown mechanism that acts to shut down reactor power production whenever the system overheats. There are a few vulnerabilities in the passive shutdown, with the most worrisome being the positive feedback from sodium density decreases or sodium voiding. Various postulated unscrammed events were examined by GE and/or BNL, and much of the analysis discussed in this report is focused on this category of events. For the most part, the BNL evaluations confirm the information submitted by General Electric. The principal areas of concern are related to the performance of the ternary metal fuel, and may be resolved as ANL continues with its fuel development and testing program

Vitrification Facility integrated system performance testing report

International Nuclear Information System (INIS)

Elliott, D.

1997-01-01

This report provides a summary of component and system performance testing associated with the Vitrification Facility (VF) following construction turnover. The VF at the West Valley Demonstration Project (WVDP) was designed to convert stored radioactive waste into a stable glass form for eventual disposal in a federal repository. Following an initial Functional and Checkout Testing of Systems (FACTS) Program and subsequent conversion of test stand equipment into the final VF, a testing program was executed to demonstrate successful performance of the components, subsystems, and systems that make up the vitrification process. Systems were started up and brought on line as construction was completed, until integrated system operation could be demonstrated to produce borosilicate glass using nonradioactive waste simulant. Integrated system testing and operation culminated with a successful Operational Readiness Review (ORR) and Department of Energy (DOE) approval to initiate vitrification of high-level waste (HLW) on June 19, 1996. Performance and integrated operational test runs conducted during the test program provided a means for critical examination, observation, and evaluation of the vitrification system. Test data taken for each Test Instruction Procedure (TIP) was used to evaluate component performance against system design and acceptance criteria, while test observations were used to correct, modify, or improve system operation. This process was critical in establishing operating conditions for the entire vitrification process

Severe fuel-damage scoping test performance

International Nuclear Information System (INIS)

Gruen, G.E.; Buescher, B.J.

1983-01-01

As a result of the Three Mile Island Unit-2 (TMI-2) accident, the Nuclear Regulatory Commission has initiated a severe fuel damage test program to evaluate fuel rod and core response during severe accidents similar to TMI-2. The first test of Phase I of this series has been successfully completed in the Power Burst Facility at the Idaho National Engineering Laboratory. Following the first test, calculations were performed using the TRAC-BD1 computer code with actual experimental boundary conditions. This paper discusses the test conduct and performance and presents the calculated and measured test bundle results. The test resulted in a slow heatup to 2000 K over about 4 h, with an accelerated reaction of the zirconium cladding at temperatures above 1600 K in the lower part or the bundle and 2000 K in the upper portion of the bundle

Failure of aseptic revision total knee arthroplasties.

Science.gov (United States)

Leta, Tesfaye H; Lygre, Stein Håkon L; Skredderstuen, Arne; Hallan, Geir; Furnes, Ove

2015-02-01

In Norway, the proportion of revision knee arthroplasties increased from 6.9% in 1994 to 8.5% in 2011. However, there is limited information on the epidemiology and causes of subsequent failure of revision knee arthroplasty. We therefore studied survival rate and determined the modes of failure of aseptic revision total knee arthroplasties. This study was based on 1,016 aseptic revision total knee arthroplasties reported to the Norwegian Arthroplasty Register between 1994 and 2011. Revisions done for infections were not included. Kaplan-Meier and Cox regression analyses were used to assess the survival rate and the relative risk of re-revision with all causes of re-revision as endpoint. 145 knees failed after revision total knee arthroplasty. Deep infection was the most frequent cause of re-revision (28%), followed by instability (26%), loose tibial component (17%), and pain (10%). The cumulative survival rate for revision total knee arthroplasties was 85% at 5 years, 78% at 10 years, and 71% at 15 years. Revision total knee arthroplasties with exchange of the femoral or tibial component exclusively had a higher risk of re-revision (RR = 1.7) than those with exchange of the whole prosthesis. The risk of re-revision was higher for men (RR = 2.0) and for patients aged less than 60 years (RR = 1.6). In terms of implant survival, revision of the whole implant was better than revision of 1 component only. Young age and male sex were risk factors for re-revision. Deep infection was the most frequent cause of failure of revision of aseptic total knee arthroplasties.

RELATIONSHIPS BETWEEN FUNCTIONAL MOVEMENT TESTS AND PERFORMANCE TESTS IN YOUNG ELITE MALE BASKETBALL PLAYERS.

Science.gov (United States)

Gonzalo-Skok, Oliver; Serna, Jorge; Rhea, Matthew R; Marín, Pedro J

2015-10-01

Sprinting and jumping are two common and important components of high-level sport performance. The weight-bearing dorsiflexion test (WB-DF) and Star Excursion Balance Test (SEBT) are tools developed to identify athletes at risk for lower extremity injury and may be related to running and jumping performance among athletes. The purposes of the present study were: 1) to identify any relationships between functional movement tests (WB-DF and SEBT) and performance tests (jumping, sprinting and changing direction); 2) to examine any relationships between asymmetries in functional movements and performance tests. Descriptive cohort study. Fifteen elite male basketball players (age: 15.4 ± 0.9 years) were assessed during a three-week period to determine the reliability of functional screening tools and performance tests and to examine the relationships between these tests. Relative (intraclass correlation coefficient) and absolute (coefficient of variation) reliability were used to assess the reproducibility of the tests. Significant correlations were detected between certain functional movement tests and performance tests. Both left and right excursion composite scores related to slower performance times in sprint testing, demonstrating that greater dynamic reach relates to decreased quickness and acceleration among these elite basketball athletes. The various relationships between dynamic functional movement testing, speed, and jump performance provide guidance for the strength and conditioning professional when conducting and evaluating data in an effort to improve performance and reduce risk of injury. The results of the present study suggest that these functional and performance tests do not measure the same components of human movement, and could be paired as outcome measures for the clinical and sport assessment of lower extremity function. 2b.

Respiratory protection standard: comments on OSHA's proposed revision.

Science.gov (United States)

Decker, M D

1995-06-01

On November 15, 1994, the Occupational Safety and Health Administration (OSHA) published in the Federal Register (59:58884-58956) the draft of a proposed revision of the Respiratory Protection Standard. One of OSHA's oldest standards, the Respiratory Protection Standard defines the conduct of the employer (eg, hospital) with respect to respirator training, fit testing, medical examinations, use, storage, and so on. The proposed revision appears to have been drafted with no consideration for its effect on healthcare workers or the healthcare industry. SHEA has prepared the following comments to OSHA, which have been submitted to the docket and will be presented at public hearings later this month.

Using an interlaboratory study to revise methods for conducting 10-d to 42-d water or sediment toxicity tests with Hyalella azteca

Science.gov (United States)

Ivey, Chris D.; Ingersoll, Christopher G.; Brumbaugh, William G.; Hammer, Edward J.; Mount, David R.; Hockett, J. Russell; Norberg-King, Teresa J.; Soucek, Dave; Taylor, Lisa

2016-01-01

Studies have been conducted to refine US Environmental Protection Agency, ASTM International, and Environment Canada standard methods for conducting 42-d reproduction tests with Hyalella azteca in water or in sediment. Modifications to the H. azteca method include better-defined ionic composition requirements for exposure water (i.e., >15 mg/L of chloride and >0.02 mg/L of bromide) and improved survival, growth, and reproduction with alternate diets provided as increased rations over time in water-only or whole-sediment toxicity tests. A total of 24 laboratories volunteered to participate in the present interlaboratory study evaluating the performance of H. azteca in 42-d studies in control sand or control sediment using the refined methods. Improved growth and reproduction of H. azteca was observed with 2 alternate diets of 1) ramped diatoms (Thalassiosira weissflogii) + ramped Tetramin or 2) yeast–cerophyll–trout chow (YCT) + ramped Tetramin, especially when compared with results from the traditional diet of 1.8 mg YCT/d. Laboratories were able to meet proposed test acceptability criteria and in most cases had lower variation in growth or reproduction compared with previous interlaboratory studies using the traditional YCT diet. Laboratory success in conducting 42-d H. azteca exposures benefited from adherence to several key requirements of the detailed testing, culturing, and handling methods. Results from the present interlaboratory study are being used to help revise standard methods for conducting 10-d to 42-d water or sediment toxicity exposures with H. azteca.

Improving ESL Placement Tests Using Two Perspectives.

Science.gov (United States)

Brown, James Dean

1989-01-01

Criterion-referenced testing was used to complement norm-referenced procedures in a revision of a university's English-as-a-Second-Language placement test for reading. Test validation results indicated that the revised test better matched the university's program and included more items related to the content and skills that students were…

Optimizing the performance of Hyalella azteca in chronic toxicity tests: Results of feeding studies with various foods and feeding regimes

Science.gov (United States)

The freshwater amphipod Hyalella azteca is a common organism used for sediment toxicity testing in the United States and elsewhere. Standard methods for 10-d and 42-d toxicity tests with H. azteca were last revised and published by USEPA/ASTM in 2000. Under the methods in the man...

Chemical oil-spill dispersants: evaluation of three laboratory procedures for estimating performance

International Nuclear Information System (INIS)

Clayton, J.R.; Marsden, P.

1992-09-01

The report presents data from studies designed to evaluate characteristics of selected bench-scale test methods for estimating performance of chemical agents for dispersing oil from surface slicks into an underlying water column. In order to mitigate the effect of surface slicks with chemical dispersant agents, however, an on-scene coordinator must have information and an understanding of performance characteristics for available dispersant agents. Performance of candidate dispersant agents can be estimated on the basis of laboratory testing procedures that are designed to evaluate performance of different agents. Data presented in the report assist in the evaluation of candidate test methods for estimating performance of candidate dispersant agents. Three test methods were selected for evaluating performance: the currently accepted Revised Standard EPA test, Environmental Canada's Swirling Flask test, and the IFP-Dilution test

Performance Testing of Download Services of COSMC

Directory of Open Access Journals (Sweden)

Jiří Horák

2013-11-01

Full Text Available The paper presents results of performance tests of download services of Czech Office of Surveying, Mapping and Cadastre according to INSPIRE  requirements. Methodology of testing is explained, including monitoring performance  of reference servers. 26 millions of random requests were generated for each monitored operation, layer and coordinate system. The temporal development of performance indicators are analyzed and discussed. Results of performance tests approve the compliance with INSPIRE qualitative requirements for download services. All monitored services satisfy requirements of latency, capacity and availability. The latency and availability requirements are fulfilled with an abundant reserve. No problems in structure and content of responses were detected.

System Performance and Testing

NARCIS (Netherlands)

Frei, U.; Oversloot, H.

2004-01-01

This chapter compares and contrasts the system performance of two widely used solar thermal systems using testing and simulation programs. Solar thermal systems are used in many countries for heating domestically used water. In addition to the simple thermosiphon systems, better designed pumped

Validation of a clinical critical thinking skills test in nursing.

Science.gov (United States)

Shin, Sujin; Jung, Dukyoo; Kim, Sungeun

2015-01-27

The purpose of this study was to develop a revised version of the clinical critical thinking skills test (CCTS) and to subsequently validate its performance. This study is a secondary analysis of the CCTS. Data were obtained from a convenience sample of 284 college students in June 2011. Thirty items were analyzed using item response theory and test reliability was assessed. Test-retest reliability was measured using the results of 20 nursing college and graduate school students in July 2013. The content validity of the revised items was analyzed by calculating the degree of agreement between instrument developer intention in item development and the judgments of six experts. To analyze response process validity, qualitative data related to the response processes of nine nursing college students obtained through cognitive interviews were analyzed. Out of initial 30 items, 11 items were excluded after the analysis of difficulty and discrimination parameter. When the 19 items of the revised version of the CCTS were analyzed, levels of item difficulty were found to be relatively low and levels of discrimination were found to be appropriate or high. The degree of agreement between item developer intention and expert judgments equaled or exceeded 50%. From above results, evidence of the response process validity was demonstrated, indicating that subjects respondeds as intended by the test developer. The revised 19-item CCTS was found to have sufficient reliability and validity and will therefore represents a more convenient measurement of critical thinking ability.

Total hip arthroplasty revision due to infection: a cost analysis approach.

Science.gov (United States)

Klouche, S; Sariali, E; Mamoudy, P

2010-04-01

The treatment of total hip arthroplasty (THA) infections is long and costly. However,the number of studies in the literature analysing the real cost of THA revision in relation to their etiology, including infection, is limited. The aim of this retrospective study was to determine the cost of revision of infected THA and to compare these costs to those of primary THA and revision of non-infected THA. We performed a retrospective cost analysis for the year 2006 using an identical analytic accounting system in each hospital department (according to internal criteria) based on allotment of direct costs and receipts for each department. From January to December 2006, 424 primary THA, 57 non-infected THA revisions and 40 THA revisions due to infection were performed. The different cost areas of the patient's treatment were identified.This included preoperative medical work-up, medicosurgical management during hospital stay,a second stay in an orthopedic rehabilitation hospital (ORH) and post-hospitalisation antibiotic therapy after revision due to infection, as well as home-based hospitalisation (HH) costs, if this was the selected alternative option. We used the national health insurance fee schedule found in the "Common classification of medical procedures" and the "General nomenclature of professional procedures" applicable in France since September 1, 2005. Hospital costs included direct costs (hospital overhead costs) and indirect costs, (medical, surgical, technical settings and net general service expenses). The calculation of HH costs and ORH costs were based on the average daily charge of these departments. The cost of primary THA was used as the reference.We then compared our surgical costs with those found for the corresponding comparable hospital stay groups (Groupes homogènes de séjour). The average hospital stay (AHS) was 7.5 +/- 1.8 days for primary THA, 8.9 +/- 2.2 days for non-infected revisions and 30.6 +/- 14.9 days for revisions due to infection

The 1st VIPEX Software Testing Report (Version 3.1)

International Nuclear Information System (INIS)

Choi, Sun Yeong; Jung, Woo Sik; Seo, Jae Seung

2009-09-01

The purposes of this report are (1) to perform a Verification and Validation (V and V) test for the VIPEX(Vital-area Identification Package EXpert) software and (2) to improve a software quality through the V and V test. The VIPEX was developed in Korea Atomic Energy Research Institute (KAERI) for the Vital Area Identification (VAI) of nuclear power plants. The version of the VIPEX which was distributed is 3.1. The VIPEX was revised based on the first V and V test and the second V and V test will be performed. We have performed the following tasks for the first V and V test on Windows XP and VISTA operating systems: - Testing basic function including fault tree editing - Writing formal reports

Cascade Distiller System Performance Testing Interim Results

Science.gov (United States)

Callahan, Michael R.; Pensinger, Stuart; Sargusingh, Miriam J.

2014-01-01

The Cascade Distillation System (CDS) is a rotary distillation system with potential for greater reliability and lower energy costs than existing distillation systems. Based upon the results of the 2009 distillation comparison test (DCT) and recommendations of the expert panel, the Advanced Exploration Systems (AES) Water Recovery Project (WRP) project advanced the technology by increasing reliability of the system through redesign of bearing assemblies and improved rotor dynamics. In addition, the project improved the CDS power efficiency by optimizing the thermoelectric heat pump (TeHP) and heat exchanger design. Testing at the NASA-JSC Advanced Exploration System Water Laboratory (AES Water Lab) using a prototype Cascade Distillation Subsystem (CDS) wastewater processor (Honeywell d International, Torrance, Calif.) with test support equipment and control system developed by Johnson Space Center was performed to evaluate performance of the system with the upgrades as compared to previous system performance. The system was challenged with Solution 1 from the NASA Exploration Life Support (ELS) distillation comparison testing performed in 2009. Solution 1 consisted of a mixed stream containing human-generated urine and humidity condensate. A secondary objective of this testing is to evaluate the performance of the CDS as compared to the state of the art Distillation Assembly (DA) used in the ISS Urine Processor Assembly (UPA). This was done by challenging the system with ISS analog waste streams. This paper details the results of the AES WRP CDS performance testing.

Analysis of failed rotator cuff repair – Retrospective survey of revisions after open rotator cuff repair

Directory of Open Access Journals (Sweden)

Rupert Schupfner

2017-07-01

Full Text Available Background Rotator cuff defects are frequently occurring shoulder pathologies associated with pain and movement impairment. Aims The aim of the study was to analyse the pathologies that lead to operative revisions after primary open rotator cuff repair. Methods In 216 patients who underwent primary rotator cuff repair and later required operative revision between 1996 to 2005, pathologies found intraoperatively during the primary operation and during revision surgery were collected, analysed and compared. Results The average age at the time of revision surgery was 54.3 years. The right shoulder (61.6 per cent was more often affected than the left, males (63.4 per cent more often than females. At primary operation – apart from rotator cuff repair – there were the following surgical procedures performed: 190 acromioplasty, 86 Acromiclavicular joint resections, 68 tenodesis, 40 adhesiolysis and 1 tenotomy. If an ACJ-resection had been performed in the primary operation, ACJ-problems were rare in revision surgery (p<0.01. Primary gleno-humeral adhesions were associated with a significant rise in re-tearing rate (p=0.049. Primary absence of adhesions went along with a significant lower rate of adhesions found at revision (p=0.018. Primary performed acromioplasty had no influence on re-tearing rate (p=0.408 or on the rate of subacromial impingement at revision surgery (p=0.709. Conclusion To avoid operative revision after rotator cuff repair relevant copathologies of the shoulder have to be identified before or during operation and treated accordingly. Therefore, even during open rotator cuff repair, the surgeon should initially start with arthroscopy of the shoulder joint and subacromial space to recognise co-pathologies.

Risk factors for revision of primary total hip arthroplasty: a systematic review

Directory of Open Access Journals (Sweden)

Prokopetz Julian JZ

2012-12-01

Full Text Available Abstract Background Numerous papers have been published examining risk factors for revision of primary total hip arthroplasty (THA, but there have been no comprehensive systematic literature reviews that summarize the most recent findings across a broad range of potential predictors. Methods We performed a PubMed search for papers published between January, 2000 and November, 2010 that provided data on risk factors for revision of primary THA. We collected data on revision for any reason, as well as on revision for aseptic loosening, infection, or dislocation. For each risk factor that was examined in at least three papers, we summarize the number and direction of statistically significant associations reported. Results Eighty-six papers were included in our review. Factors found to be associated with revision included younger age, greater comorbidity, a diagnosis of avascular necrosis (AVN as compared to osteoarthritis (OA, low surgeon volume, and larger femoral head size. Male sex was associated with revision due to aseptic loosening and infection. Longer operating time was associated with revision due to infection. Smaller femoral head size was associated with revision due to dislocation. Conclusions This systematic review of literature published between 2000 and 2010 identified a range of demographic, clinical, surgical, implant, and provider variables associated with the risk of revision following primary THA. These findings can inform discussions between surgeons and patients relating to the risks and benefits of undergoing total hip arthroplasty.

Test anxiety, perfectionism, goal orientation, and academic performance.

Science.gov (United States)

Eum, KoUn; Rice, Kenneth G

2011-03-01

Dimensions of perfectionism and goal orientation have been reported to have differential relationships with test anxiety. However, the degree of inter-relationship between different dimensions of perfectionism, the 2 × 2 model of goal orientations proposed by Elliot and McGregor, cognitive test anxiety, and academic performance indicators is not known. Based on data from 134 university students, we conducted correlation and regression analyses to test associations between adaptive and maladaptive perfectionism, four types of goal orientations, cognitive test anxiety, and two indicators of academic performance: proximal cognitive performance on a word list recall test and distal academic performance in terms of grade point average. Cognitive test anxiety was inversely associated with both performance indicators, and positively associated with maladaptive perfectionism and avoidance goal orientations. Adaptive and maladaptive perfectionism accounted for significant variance in cognitive test anxiety after controlling for approach and avoidance goal orientations. Overall, nearly 50% of the variance in cognitive test anxiety could be attributed to gender, goal orientations, and perfectionism. Results suggested that students who are highly test anxious are likely to be women who endorse avoidance goal orientations and are maladaptively perfectionistic.

A Translation and Validation Study of the Life Orientation Test Revised in the Greek Speaking Population of Nurses among Three Hospitals in Athens and Ioannina

Science.gov (United States)

Lyrakos, George N.; Damigos, Dimitrios; Mavreas, Venetsanos; Georgia, Kostopanagiotou; Dimoliatis, Ioannis D. K.

2010-01-01

The life orientation test-revised (LOT-R) (Scheier et al. in "Journal of Personality and Social Psychology" 67:1063-1078, 1994) is a brief measure for assessing dispositional optimism. The aim of this study was to develop a Greek language version of the LOT-R and to assess the instrument's psychometric properties. The LOT-R was…

Performance testing With JMeter 29

CERN Document Server

Erinle, Bayo

2013-01-01

Performance Testing With JMeter 2.9 is a standard tutorial that will help you polish your fundamentals, guide you through various advanced topics, and along the process help you learn new tools and skills.This book is for developers, quality assurance engineers, testers, and test managers new to Apache JMeter, or those who are looking to get a good grounding in how to effectively use and become proficient with it. No prior testing experience is required.

Addendum to ''Test Plan: Small-Scale Seal Performance Tests (SSSPT)''

International Nuclear Information System (INIS)

Finley, R.E.

1992-01-01

This document describes activities that are intended to update the data base of fluid flow measurements made on expansive salt concrete (ESC) seals as part of the Small-Scale Seal Performance Tests (SSSPT). The original plans for the SSSPT experiments are described by Stormont (1985a and 1985b). These seals have previously been tested with brine and gas during the early stages (less than 450 days) after emplacement. The purpose of this Test Plan Addendum is to detail the activities necessary to, update the gas and brine measurements previously performed on the SSSPT Series A and Series B seals and to identify the key personnel responsible for implementing these activities. This addendum describes a limited undertaking and does NOT change the scope of the original test plan

Bibliocable. Revised Edition.

Science.gov (United States)

Cable Television Information Center, Washington, DC.

This selective, annotated bibliography is a revision of the original published in 1972 (ED 071 402). Some 104 books, articles, and reports included here deal with access, applications, franchising, regulation, technology, and other aspects of cable television. The listings are of two types in each category. First are revisions of the original…

Tank Monitor and Control System (TMACS) Rev 11.0 Acceptance Test Review

Energy Technology Data Exchange (ETDEWEB)

HOLM, M.J.

1999-08-25

The purpose of this document is to describe tests performed to validate Revision 11 of the TMACS Monitor and Control System (TMACS) and verify that the software functions as intended by design. This document is intended to test the software portion of TMACS. The tests will be performed on the development system. The software to be tested is the TMACS knowledge bases (KB) and the I/O driver/services. The development system will not be talking to field equipment; instead, the field equipment is simulated using emulators or multiplexers in the lab.

Drop performance test and evaluation for HANARO shutoff units

International Nuclear Information System (INIS)

Jung, Y. H.; Cho, Y. K.; Lee, J. H.; Choi, Y. S.; Woo, J. S.

2004-01-01

The function of the shutoff units of the HANARO is to rapidly insert the shutoff rod into the reactor core for safe shutdown of reactor. This paper describes drop performance test and evaluation for a shutoff unit for the technical verification of lifetime extension and localization of the HANARO shutoff units. We have performed preliminary drop performance tests for a shutoff unit at 1/2-core test loop and analyzed through the comparison with the test results performed during design verification test and the results of the periodic performance test in HANARO. It shows that the results of the local fabrication, installation and alignment for the shutoff unit meet the basic performance requirements, Furthermore, the performance evaluation method of the periodic drop test of the HANARO shutoff units is a conservative method comparing with the real drop time

Current Status and Performance Tests of Korea Heat Load Test Facility KoHLT-EB

Energy Technology Data Exchange (ETDEWEB)

Kim, Sukkwon; Jin, Hyunggon; Shin, Kyuin; Choi, Boguen; Lee, Eohwak; Yoon, Jaesung; Lee, Dongwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Duckhoi; Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

2013-05-15

A commissioning test has been scheduled to establish the installation and preliminary performance experiments of the copper hypervapotron mockups. And a qualification test will be performed to evaluate the CuCrZr duct liner in the ITER neutral beam injection facility and the ITER first wall small-scale mockups of the semi-prototype, at up to 1.5 and 5 MW/m{sup 2} high heat flux. Also, this system will be used to test other PFCs for ITER and materials for tokamak reactors. Korean high heat flux test facility(KoHLT-EB; Korea Heat Load Test facility - Electron Beam) by using an electron beam system has been constructed in KAERI to perform the qualification test for ITER blanket FW semi-prototype mockups, hypervapotron cooling devices in fusion devices, and other ITER plasma facing components. The commissioning and performance tests with the supplier of e-gun system have been performed on November 2012. The high heat flux test for hypervapotron cooling device and calorimetry were performed to measure the surface heat flux, the temperature profile and cooling performance. Korean high heat flux test facility for the plasma facing components of nuclear fusion machines will be constructed to evaluate the performance of each component. This facility for the plasma facing materials will be equipped with an electron beam system with a 60 kV acceleration gun.

The Epidemiology of Revision Anterior Cruciate Ligament Reconstruction in Adults from Ontario, Canada

Science.gov (United States)

Leroux, Timothy; Wasserstein, David; Dwyer, Tim; Ogilvie-Harris, Darrell; Marks, Paul H.; Bach, Bernard R.; Townley, John; Mahomed, Nizar; Chahal, Jaskarndip

2015-01-01

Objectives: The morbidity associated with revision anterior cruciate ligament reconstruction (ACLR) is largely unknown. The objective of this study was to determine the rate of and risk factors for re-revision, re-operation, and re-admission following revision ACLR in the general population. Methods: All patients who underwent first revision ACLR in Ontario, Canada from January 2004 to December 2010 were identified and followed to December 2012. Exclusions included age (<16 years), previous osteotomy, or multi-ligament knee reconstruction. The main outcome was re-revision ACLR. Secondary outcomes included re-operation [irrigation and debridement (I&D), meniscectomy, manipulation under anesthesia (MUA), contralateral ACLR, and total knee arthroplasty (TKA)], and re-admission within 90 days of surgery. Survival to re-revision was determined using the Kaplan-Meier (KM) approach. A Cox proportional hazards model or logistic regression were used to determine the influence of patient factors (age, sex, neighborhood income quintile, and comorbidity), surgical factors (graft choice, concurrent meniscal procedure, and fixation method), and provider factors (surgeon volume, surgeon years in practice, and hospital status) on outcomes. A post-hoc analysis was performed to determine the influence of the aforementioned factors on overall post-operative infection risk, including both operative and non-operative cases. Results: Overall, 827 patients were included (median age: 30 years; 58.8% males). Single stage revisions comprised 92.9% of cases, and a meniscal procedure (repair or debridement) was performed in 45.3% of cases. The re-revision rate at a mean follow-up of 4.8±2.2 years was 4.4%, and the five-year survival rate was 95.4% (Figure 1). The rates of I&D, meniscectomy, contralateral ACLR, and re-admission were 0.8%, 3.1%, 3.4%, and 4.1%, respectively. MUA and TKA were rare. Young age significantly increased contralateral ACLR risk (risk decreased by 5.1% with each year

Cost Implications of Primary Versus Revision Surgery in Adult Spinal Deformity.

Science.gov (United States)

Qureshi, Rabia; Puvanesarajah, Varun; Jain, Amit; Kebaish, Khaled; Shimer, Adam; Shen, Francis; Hassanzadeh, Hamid

2017-08-01

Adult spinal deformity (ASD) is an important problem to consider in the elderly. Although studies have examined the complications of ASD surgery and have compared functional and radiographic results of primary surgery versus revision, no studies have compared the costs of primary procedures with revisions. We assessed the in-hospital costs of these 2 surgery types in patients with ASD. The PearlDiver Database, a database of Medicare records, was used in this study. Mutually exclusive groups of patients undergoing primary or revision surgery were identified. Patients in each group were queried for age, sex, and comorbidities. Thirty-day readmission rates, 30-day and 90-day complication rates, and postoperative costs of care were assessed with multivariate analysis. For analyses, significance was set at P average reimbursement of the primary surgery cohort was $57,078 ± $30,767. Reimbursement of revision surgery cohort was $52,999 ± $27,658. The adjusted difference in average costs between the 2 groups is $4773 ± $1069 (P day and 90-day adjusted difference in cost of care when sustaining any of the major medical complications in primary surgery versus revision surgery was insignificant. Patients undergoing primary and revision corrective procedures for ASD have similar readmission rates, lengths of stays, and complication rates. Our data showed a higher cost of primary surgery compared with revision surgery, although costs of sustaining postoperative complications were similar. This finding supports the decision to perform revision procedures in patients with ASD when indicated because neither outcomes nor costs are a hindrance to correction. Copyright © 2017 Elsevier Inc. All rights reserved.

A revised radiation package of G-packed McICA and two-stream approximation: Performance evaluation in a global weather forecasting model

Science.gov (United States)

Baek, Sunghye

2017-07-01

For more efficient and accurate computation of radiative flux, improvements have been achieved in two aspects, integration of the radiative transfer equation over space and angle. First, the treatment of the Monte Carlo-independent column approximation (MCICA) is modified focusing on efficiency using a reduced number of random samples ("G-packed") within a reconstructed and unified radiation package. The original McICA takes 20% of CPU time of radiation in the Global/Regional Integrated Model systems (GRIMs). The CPU time consumption of McICA is reduced by 70% without compromising accuracy. Second, parameterizations of shortwave two-stream approximations are revised to reduce errors with respect to the 16-stream discrete ordinate method. Delta-scaled two-stream approximation (TSA) is almost unanimously used in Global Circulation Model (GCM) but contains systematic errors which overestimate forward peak scattering as solar elevation decreases. These errors are alleviated by adjusting the parameterizations of each scattering element—aerosol, liquid, ice and snow cloud particles. Parameterizations are determined with 20,129 atmospheric columns of the GRIMs data and tested with 13,422 independent data columns. The result shows that the root-mean-square error (RMSE) over the all atmospheric layers is decreased by 39% on average without significant increase in computational time. Revised TSA developed and validated with a separate one-dimensional model is mounted on GRIMs for mid-term numerical weather forecasting. Monthly averaged global forecast skill scores are unchanged with revised TSA but the temperature at lower levels of the atmosphere (pressure ≥ 700 hPa) is slightly increased (< 0.5 K) with corrected atmospheric absorption.

Psychometric Validation of the Revised Family Affluence Scale

DEFF Research Database (Denmark)

Torsheim, Torbjorn; Cavallo, Franco; Levin, Kate Ann

2016-01-01

The aim was to develop and test a brief revised version of the family affluence scale. A total of 7120 students from Denmark, Greenland, Italy, Norway, Poland, Romania, Scotland and Slovakia reported on a list of 16 potential indicators of affluence. Responses were subject to item screening and t...

Recommended procedures for performance testing of radiobioassay laboratories: Volume 3, In vivo test phantoms

International Nuclear Information System (INIS)

MacLellan, J.A.; Traub, R.J.

1988-11-01

Draft American National Standards Institute (ANSI) Standard N13.30 (Performance Criteria for Radiobioassay) was developed for the US Department of Energy and the US Nuclear Regulatory Commission to help ensure that bioassay laboratories provide accurate and consistent results. The draft standard describes the procedures necessary to establish a bioassay performance-testing laboratory and program. The bioassay performance-testing laboratory will conduct tests to evaluate the performance of service laboratories. Pacific Northwest Laboratory helped develop testing procedures as part of an effort to evaluate the draft ANSI N13.30 performance criteria by testing the existing measurement capabilities of various bioassay laboratories. This report recommends guidelines for the preparation, handling, storage, distribution, shipping, and documentation of test phantoms used for calibration of measurement systems for direct bioassay. The data base and recommended records system for documenting radiobioassay performance at the service laboratories are also presented

Load responsive multilayer insulation performance testing

Energy Technology Data Exchange (ETDEWEB)

Dye, S.; Kopelove, A. [Quest Thermal Group, 6452 Fig Street Suite A, Arvada, CO 80004 (United States); Mills, G. L. [Ball Aerospace and Technologies Corp, 1600 Commerce Street, Boulder, CO 80301 (United States)

2014-01-29

Cryogenic insulation designed to operate at various pressures from one atmosphere to vacuum, with high thermal performance and light weight, is needed for cryogenically fueled space launch vehicles and aircraft. Multilayer insulation (MLI) performs well in a high vacuum, but the required vacuum shell for use in the atmosphere is heavy. Spray-on foam insulation (SOFI) is often used in these systems because of its light weight, but can have a higher heat flux than desired. We report on the continued development of Load Responsive Multilayer Insulation (LRMLI), an advanced thermal insulation system that uses dynamic beam discrete spacers that provide high thermal performance both in atmosphere and vacuum. LRMLI consists of layers of thermal radiation barriers separated and supported by micromolded polymer spacers. The spacers have low thermal conductance, and self-support a thin, lightweight vacuum shell that provides internal high vacuum in the insulation. The dynamic load responsive spacers compress to support the external load of a vacuum shell in one atmosphere, and decompress under reduced atmospheric pressure for lower heat leak. Structural load testing was performed on the spacers with various configurations. LRMLI was installed on a 400 liter tank and boil off testing with liquid nitrogen performed at various chamber pressures from one atmosphere to high vacuum. Testing was also performed with an MLI blanket on the outside of the LRMLI.

Load responsive multilayer insulation performance testing

International Nuclear Information System (INIS)

Dye, S.; Kopelove, A.; Mills, G. L.

2014-01-01

Cryogenic insulation designed to operate at various pressures from one atmosphere to vacuum, with high thermal performance and light weight, is needed for cryogenically fueled space launch vehicles and aircraft. Multilayer insulation (MLI) performs well in a high vacuum, but the required vacuum shell for use in the atmosphere is heavy. Spray-on foam insulation (SOFI) is often used in these systems because of its light weight, but can have a higher heat flux than desired. We report on the continued development of Load Responsive Multilayer Insulation (LRMLI), an advanced thermal insulation system that uses dynamic beam discrete spacers that provide high thermal performance both in atmosphere and vacuum. LRMLI consists of layers of thermal radiation barriers separated and supported by micromolded polymer spacers. The spacers have low thermal conductance, and self-support a thin, lightweight vacuum shell that provides internal high vacuum in the insulation. The dynamic load responsive spacers compress to support the external load of a vacuum shell in one atmosphere, and decompress under reduced atmospheric pressure for lower heat leak. Structural load testing was performed on the spacers with various configurations. LRMLI was installed on a 400 liter tank and boil off testing with liquid nitrogen performed at various chamber pressures from one atmosphere to high vacuum. Testing was also performed with an MLI blanket on the outside of the LRMLI

Do medical student stress, health, or quality of life foretell step 1 scores? A comparison of students in traditional and revised preclinical curricula.

Science.gov (United States)

Tucker, Phebe; Jeon-Slaughter, Haekyung; Sener, Ugur; Arvidson, Megan; Khalafian, Andrey

2015-01-01

We explored the theory that measures of medical students' well-being and stress from different types of preclinical curricula are linked with performance on standardized assessment. Self-reported stress and quality of life among sophomore medical students having different types of preclinical curricula will vary in their relationships to USMLE Step 1 scores. Voluntary surveys in 2010 and 2011 compared self-reported stress, physical and mental health, and quality of life with Step 1 scores for beginning sophomore students in the final year of a traditional, discipline-based curriculum and the 1st year of a revised, systems-based curriculum with changed grading system. Wilcoxon rank sum tests and Spearman rank correlations were used to analyze data, significant at p students reported worse physical health, subjective feelings, leisure activities, social relationships and morale, and more depressive symptoms and life stress than traditional curriculum students. However, among curriculum-related stressors, few differences emerged; revised curriculum sophomores reported less stress working with real and standardized patients than traditional students. There were no class differences in respondents' Step 1 scores. Among emotional and physical health measures, only feelings of morale correlated negatively with Step 1 performance. Revised curriculum students' Step 1 scores correlated negatively with stress from difficulty of coursework. Although revised curriculum students reported worse quality of life, general stress, and health and less stress from patient interactions than traditional students, few measures were associated with performance differences on Step 1. Moreover, curriculum type did not appear to either hinder or help students' Step 1 performance. To identify and help students at risk for academic problems, future assessments of correlates of Step 1 performance should be repeated after the new curriculum is well established, relating them also to performance

Relationships Between Anaerobic Performance, Field Tests and Game Performance of Sitting Volleyball Players

Directory of Open Access Journals (Sweden)

Marszalek Jolanta

2015-12-01

Full Text Available The aim of this study was to evaluate relationships between anaerobic performance, field tests, game performance and anthropometric variables of sitting volleyball players. Twenty elite Polish sitting volleyball players were tested using the 30 s Wingate Anaerobic Test for arm crank ergometer and participated in six physical field tests. Heights in position to block and to spike, as well as arm reach were measured. Players were observed during the game on the court in terms of effectiveness of the serve, block, attack, receive and defense. Pearson analysis and the Spearman's rank correlation coefficient were used. The strongest correlations were found between the chest pass test and mean power and peak power (r=.846; p=.001 and r=.708; p=.0005, respectively, and also between the T-test and peak power (r= −.718; p=.001. Mean power correlated with the 3 m test (r= −.540; p=.014, the 5 m test (r= −.592; p=.006, and the T-test (r= −.582; p=.007. Peak power correlated with the 3 m test (r= −.632; p=.003, the 5 m test (r= −.613; p=.004, speed & agility (r= −.552; p=.012 and speed & endurance (r=−.546; p=.013. Significant correlations were observed between anthropometric parameters and anaerobic performance variables (p≤.001, and also between anthropometric parameters and field tests (p≤.05. Game performance and physical fitness of sitting volleyball players depended on their anthropometric variables: reach of arms, the position to block and to spike. The chest pass test could be used as a non-laboratory field test of anaerobic performance of sitting volleyball players.

Revisioning Theoretical Framework of Electronic Performance Support Systems (EPSS within the Software Application Examples

Directory of Open Access Journals (Sweden)

Dr. Servet BAYRAM,

2004-04-01

Full Text Available Revisioning Theoretical Framework of Electronic Performance Support Systems (EPSS within the Software Application Examples Assoc. Prof. Dr. Servet BAYRAM Computer Education & Instructional Technologies Marmara University , TURKEY ABSTRACT EPSS provides electronic support to learners in achieving a performance objective; a feature which makes it universally and consistently available on demand any time, any place, regardless of situation, without unnecessary intermediaries involved in the process. The aim of this review is to develop a set of theoretical construct that provide descriptive power for explanation of EPSS and its roots and features within the software application examples (i.e., Microsoft SharePoint Server”v2.0” Beta 2, IBM Lotus Notes 6 & Domino 6, Oracle 9i Collaboration Suite, and Mac OS X v10.2. From the educational and training point of view, the paper visualizes a pentagon model for the interrelated domains of the theoretical framework of EPSS. These domains are: learning theories, information processing theories, developmental theories, instructional theories, and acceptance theories. This descriptive framework explains a set of descriptions as to which outcomes occur under given theoretical conditions for a given EPSS model within software examples. It summarizes some of the theoretical concepts supporting to the EPSS’ related features and explains how such concepts sharing same features with the example software programs in education and job training.

IN SITU FIELD TESTING OF PROCESSES

International Nuclear Information System (INIS)

YANG, J.S.Y.

2004-01-01

The purpose of this scientific analysis report is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts and surface-based boreholes through unsaturated zone (UZ) tuff rock units. In situ testing, monitoring, and associated laboratory studies are conducted to directly assess and evaluate the waste emplacement environment and the natural barriers to radionuclide transport at Yucca Mountain. This scientific analysis report supports and provides data to UZ flow and transport model reports, which in turn contribute to the Total System Performance Assessment (TSPA) of Yucca Mountain, an important document for the license application (LA). The objectives of ambient field-testing activities are described in Section 1.1. This report is the third revision (REV 03), which supercedes2. The scientific analysis of data for inputs to model calibration and validation as documented in2 were developed in accordance with the Technical Work Plan (TWP) ''Technical Work Plan for: Performance Assessment Unsaturated Zone'' (BSC 2004 [DIRS 167969]). This revision was developed in accordance with the ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654], Section 1.2.4) for better integrated, consistent, transparent, traceable, and more complete documentation in this scientific analysis report and associated UZ flow and transport model reports. No additional testing or analyses were performed as part of this revision. The list of relevant acceptance criteria is provided by ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654]), Table 3-1. Additional deviations from the TWP regarding the features, events, and processes (FEPs) list are discussed in Section 1.3. Documentation in this report includes descriptions of how, and under what conditions, the tests were conducted. The descriptions and analyses

Guidance document for revision of DOE Order 5820.2A, Radioactive Waste Technical Support Program. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Kudera, D.E.; McMurtrey, C.D.; Meagher, B.G.

1993-04-01

This document provides guidance for the revision of DOE Order 5820.2A, ``Radioactive Waste Management.`` Technical Working Groups have been established and are responsible for writing the revised order. The Technical Working Groups will use this document as a reference for polices and procedures that have been established for the revision process. The overall intent of this guidance is to outline how the order will be revised and how the revision process will be managed. In addition, this document outlines technical issues considered for inclusion by a Department of Energy Steering Committee.

Testing Game-Based Performance in Team-Handball.

Science.gov (United States)

Wagner, Herbert; Orwat, Matthias; Hinz, Matthias; Pfusterschmied, Jürgen; Bacharach, David W; von Duvillard, Serge P; Müller, Erich

2016-10-01

Wagner, H, Orwat, M, Hinz, M, Pfusterschmied, J, Bacharach, DW, von Duvillard, SP, and Müller, E. Testing game-based performance in team-handball. J Strength Cond Res 30(10): 2794-2801, 2016-Team-handball is a fast paced game of defensive and offensive action that includes specific movements of jumping, passing, throwing, checking, and screening. To date and to the best of our knowledge, a game-based performance test (GBPT) for team-handball does not exist. Therefore, the aim of this study was to develop and validate such a test. Seventeen experienced team-handball players performed 2 GBPTs separated by 7 days between each test, an incremental treadmill running test, and a team-handball test game (TG) (2 × 20 minutes). Peak oxygen uptake (V[Combining Dot Above]O2peak), blood lactate concentration (BLC), heart rate (HR), sprinting time, time of offensive and defensive actions as well as running intensities, ball velocity, and jump height were measured in the game-based test. Reliability of the tests was calculated using an intraclass correlation coefficient (ICC). Additionally, we measured V[Combining Dot Above]O2peak in the incremental treadmill running test and BLC, HR, and running intensities in the team-handball TG to determine the validity of the GBPT. For the test-retest reliability, we found an ICC >0.70 for the peak BLC and HR, mean offense and defense time, as well as ball velocity that yielded an ICC >0.90 for the V[Combining Dot Above]O2peak in the GBPT. Percent walking and standing constituted 73% of total time. Moderate (18%) and high (9%) intensity running in the GBPT was similar to the team-handball TG. Our results indicated that the GBPT is a valid and reliable test to analyze team-handball performance (physiological and biomechanical variables) under conditions similar to competition.

Where Lab Tests Are Performed

Science.gov (United States)

... example, there may be sections that focus on microbiology, hematology, chemistry, and blood banking . Other units may perform highly specialized tests using electron microscopy and immunohistochemistry, and still others ...

Active sites environmental monitoring Program - Program Plan: Revision 2

International Nuclear Information System (INIS)

Morrissey, C.M.; Hicks, D.S.; Ashwood, T.L.; Cunningham, G.R.

1994-05-01

The Active Sites Environmental Monitoring Program (ASEMP), initiated in 1989, provides early detection and performance monitoring of active low-level-waste (LLW) and transuranic (TRU) waste facilities at Oak Ridge National Laboratory (ORNL). Several changes have recently occurred in regard to the sites that are currently used for waste storage and disposal. These changes require a second set of revisions to the ASEMP program plan. This document incorporates those revisions. This program plan presents the organization and procedures for monitoring the active sites. The program plan also provides internal reporting levels to guide the evaluation of monitoring results

Performance test for a solar water heater

Science.gov (United States)

1979-01-01

Two reports describe procedures and results of performance tests on domestic solar powered hot water system. Performance tests determine amount of energy collected by system, amount of energy delivered to solar source, power required to operate system and maintain proper tank temperature, overall system efficiency, and temperature distribution in tank.

GEM: Performance and aging tests

International Nuclear Information System (INIS)

Cho, H.S.; Kadyk, J.; Han, S.H.; Hong, W.S.; Perez-Mendez, V.; Wenzel, W.; Pitts, K.; Martin, M.D.; Hutchins, J.B.

1999-01-01

Performance and aging tests have been done to characterize Gas Electron Multipliers (GEMs), including further design improvements such as a thicker GEM and a closed GEM. Since the effective GEM gain is typically smaller than the absolute GEM gain, due to trapping of avalanche electrons at the bottom GEM electrode, the authors performed field simulations and measurements for better understanding, and discuss methods to eliminate this effect. Other performance parameters of the GEMs are also presented, including absolute GEM gain, short-term and long-term gain stabilities

Maintenance Plan for the Performance Assessments and Composite Analyses for the Area 3 and Area 5 Radioactive Waste Management Sites at the Nevada Test Site

International Nuclear Information System (INIS)

V. Yucel

2002-01-01

U.S. Department of Energy (DOE) Order 435.1 requires that performance assessments (PAs) and composite analyses (CAs) for low-level waste (LLW) disposal facilities be maintained by the field offices. This plan describes the activities to be performed in maintaining the Performance Assessment (PA) and Composite Analysis (CA) for the Area 3 and Area 5 Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site (NTS). The Disposal Authorization Statement (DAS) for the continuing operations of a LLW facility at the DOE complex specifies the conditions for operations based on approval of a PA and CA, and requires the facility to implement a maintenance program to assure that these conditions will remain protective of the public health and the environment in the future. The goal of the maintenance program is to provide that assurance. The maintenance process is an iterative one in which changing conditions may result in a revision of PA and CA; the revised PA and CA may impose a different set of conditions for facility operation, closure, and postclosure. The maintenance process includes managing uncertainty, performing annual reviews, submitting annual summary reports to DOE Headquarters (DOE/HQ), carrying out special analyses, and revising the PAs and CAs, if necessary. Management of uncertainty is an essential component of the maintenance program because results of the original PAs and CAs are understood to be based on uncertain assumptions about the conceptual models; the mathematical models and parameters; and the future state of the lands, disposal facilities, and human activities. The annual reviews for the PAs include consideration of waste receipts, facility specific factors, results of monitoring, and results of research and development (R and D) activities. Likewise, results of ongoing R and D, changes in land-use planning, new information on known sources of residual radioactive materials, and identification of new sources may warrant an evaluation to

Performance testing framework for smart grid communication network

International Nuclear Information System (INIS)

Quang, D N; See, O H; Chee, L L; Xuen, C Y; Karuppiah, S

2013-01-01

Smart grid communication network is comprised of different communication mediums and technologies. Performance evaluation is one of the main concerns in smart grid communication system. In any smart grid communication implementation, to determine the performance factor of the network, a testing of an end-to-end process flow is required. Therefore, an effective and coordinated testing procedure plays a crucial role in evaluating the performance of smart grid communications. In this paper, a testing framework is proposed as a guideline to analyze and assess the performance of smart grid communication network.

Phase II Transport Model of Corrective Action Unit 98: Frenchman Flat, Nevada Test Site, Nye County, Nevada, Revision 1

Energy Technology Data Exchange (ETDEWEB)

Gregg Ruskuaff

2010-01-01

This document, the Phase II Frenchman Flat transport report, presents the results of radionuclide transport simulations that incorporate groundwater radionuclide transport model statistical and structural uncertainty, and lead to forecasts of the contaminant boundary (CB) for a set of representative models from an ensemble of possible models. This work, as described in the Federal Facility Agreement and Consent Order (FFACO) Underground Test Area (UGTA) strategy (FFACO, 1996; amended 2010), forms an essential part of the technical basis for subsequent negotiation of the compliance boundary of the Frenchman Flat corrective action unit (CAU) by Nevada Division of Environmental Protection (NDEP) and National Nuclear Security Administration Nevada Site Office (NNSA/NSO). Underground nuclear testing via deep vertical shafts was conducted at the Nevada Test Site (NTS) from 1951 until 1992. The Frenchman Flat area, the subject of this report, was used for seven years, with 10 underground nuclear tests being conducted. The U.S. Department of Energy (DOE), NNSA/NSO initiated the UGTA Project to assess and evaluate the effects of underground nuclear tests on groundwater at the NTS and vicinity through the FFACO (1996, amended 2010). The processes that will be used to complete UGTA corrective actions are described in the “Corrective Action Strategy” in the FFACO Appendix VI, Revision No. 2 (February 20, 2008).

The influence of shyness on children's test performance.

Science.gov (United States)

Crozier, W Ray; Hostettler, Kirsten

2003-09-01

Research has shown that shy children differ from their peers not only in their use of language in routine social encounters but also in formal assessments of their language development, including psychometric tests of vocabulary. There has been little examination of factors contributing to these individual differences. To investigate cognitive-competence and social anxiety interpretations of differences in children's performance on tests of vocabulary. To examine the performance of shy and less shy children under different conditions of test administration, individually with an examiner or among their peers within the familiar classroom setting. The sample consisted of 240 Year 5 pupils (122 male, 118 female) from 24 primary schools. Shy and less shy children, identified by teacher nomination and checklist ratings, completed vocabulary and mental arithmetic tests in one of three conditions, in a between-subjects design. The conditions varied individual and group administration, and oral and written responses. The conditions of test administration influenced the vocabulary test performance of shy children. They performed significantly more poorly than their peers in the two face-to-face conditions but not in the group test condition. A comparable trend for the arithmetic test was not statistically significant. Across the sample as a whole, shyness correlated significantly with test scores. Shyness does influence children's cognitive test performance and its impact is larger when children are tested face-to-face rather than in a more anonymous group setting. The results are of significance for theories of shyness and have implications for the assessment of schoolchildren.

Validation of a clinical critical thinking skills test in nursing

Directory of Open Access Journals (Sweden)

Sujin Shin

2015-01-01

Full Text Available Purpose: The purpose of this study was to develop a revised version of the clinical critical thinking skills test (CCTS and to subsequently validate its performance. Methods: This study is a secondary analysis of the CCTS. Data were obtained from a convenience sample of 284 college students in June 2011. Thirty items were analyzed using item response theory and test reliability was assessed. Test-retest reliability was measured using the results of 20 nursing college and graduate school students in July 2013. The content validity of the revised items was analyzed by calculating the degree of agreement between instrument developer intention in item development and the judgments of six experts. To analyze response process validity, qualitative data related to the response processes of nine nursing college students obtained through cognitive interviews were analyzed. Results: Out of initial 30 items, 11 items were excluded after the analysis of difficulty and discrimination parameter. When the 19 items of the revised version of the CCTS were analyzed, levels of item difficulty were found to be relatively low and levels of discrimination were found to be appropriate or high. The degree of agreement between item developer intention and expert judgments equaled or exceeded 50%. Conclusion: From above results, evidence of the response process validity was demonstrated, indicating that subjects respondeds as intended by the test developer. The revised 19-item CCTS was found to have sufficient reliability and validity and will therefore represents a more convenient measurement of critical thinking ability.

In Situ Field Testing of Processes

International Nuclear Information System (INIS)

Wang, J.

2001-01-01

The purpose of this Analysis/Model Report (AMR) is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts of the Yucca Mountain Site Characterization Project (YMP). This revision updates data and analyses presented in the initial issue of this AMR. This AMR was developed in accordance with the ''Technical Work Plan for Unsaturated Zone (UZ) Flow and Transport Process Model Report'' and ''Technical Work Plan for UZ Flow, Transport, and Coupled Processes Process Model Report. These activities were performed to investigate in situ flow and transport processes. The evaluations provide the necessary framework to: (1) refine and confirm the conceptual model of matrix and fracture processes in the unsaturated zone (UZ) and (2) analyze the impact of excavation (including use of construction water and effect of ventilation) on the UZ flow and transport processes. This AMR is intended to support revisions to ''Conceptual and Numerical Models for UZ Flow and Transport'' and ''Unsaturated Zone Flow and Transport Model Process Model Report''. In general, the results discussed in this AMR are from studies conducted using a combination or a subset of the following three approaches: (1) air-injection tests, (2) liquid-release tests, and (3) moisture monitoring using in-drift sensors or in-borehole sensors, to evaluate the impact of excavation, ventilation, and construction-water usage on the surrounding rocks. The liquid-release tests and air-injection tests provide an evaluation of in situ fracture flow and the competing processes of matrix imbibition. Only the findings from testing and data not covered in the ''Seepage Calibration Model and Seepage Testing Data'' are analyzed in detail in the AMR

Are revised models better models? A skill score assessment of regional interannual variability

Science.gov (United States)

Sperber, Kenneth R.; Participating AMIP Modelling Groups

1999-05-01

Various skill scores are used to assess the performance of revised models relative to their original configurations. The interannual variability of all-India, Sahel and Nordeste rainfall and summer monsoon windshear is examined in integrations performed under the experimental design of the Atmospheric Model Intercomparison Project. For the indices considered, the revised models exhibit greater fidelity at simulating the observed interannual variability. Interannual variability of all-India rainfall is better simulated by models that have a more realistic rainfall climatology in the vicinity of India, indicating the beneficial effect of reducing systematic model error.

Preliminary test conditions for KNGR SBLOCA DVI ECCS performance test

International Nuclear Information System (INIS)

Bae, Kyoo Whan; Song, Jin Ho; Chung, Young Jong; Sim, Suk Ku; Park, Jong Kyun

1999-03-01

The Korean Next Generation Reactor (KNGR) adopts 4-train Direct Vessel Injection (DVI) configuration and injects the safety injection water directly into the downcomer through the 8.5'' DVI nozzle. Thus, the thermal hydraulic phenomena such as ECCS mixing and bypass are expected to be different from those observed in the cold leg injection. In order to investigate the realistic injection phenomena and modify the analysis code developed in the basis of cold leg injection, thermal hydraulic test with the performance evaluation is required. Preliminarily, the sequence of events and major thermal hydraulic phenomena during the small break LOCA for KNGR are identified from the analysis results calculated by the CEFLASH-4AS/REM. It is shown from the analysis results that the major transient behaviors including the core mixture level are largely affected by the downcomer modeling. Therefore, to investigate the proper thermal hydraulic phenomena occurring in the downcomer with limited budget and time, the separate effects test focusing on this region is considered to be effective and the conceptual test facility based on this recommended. For this test facility the test initial and boundary conditions are developed using the CEFLASH-4AS/REM analysis results that will be used as input for the preliminary test requirements. The final test requirements will be developed through the further discussions with the test performance group. (Author). 10 refs., 18 tabs., 4 figs

Mechanical Design of a Performance Test Rig for the Turbine Air-Flow Task (TAFT)

Science.gov (United States)

Forbes, John C.; Xenofos, George D.; Farrow, John L.; Tyler, Tom; Williams, Robert; Sargent, Scott; Moharos, Jozsef

2004-01-01

To support development of the Boeing-Rocketdyne RS84 rocket engine, a full-flow, reaction turbine geometry was integrated into the NASA-MSFC turbine air-flow test facility. A mechanical design was generated which minimized the amount of new hardware while incorporating all test and instrumentation requirements. This paper provides details of the mechanical design for this Turbine Air-Flow Task (TAFT) test rig. The mechanical design process utilized for this task included the following basic stages: Conceptual Design. Preliminary Design. Detailed Design. Baseline of Design (including Configuration Control and Drawing Revision). Fabrication. Assembly. During the design process, many lessons were learned that should benefit future test rig design projects. Of primary importance are well-defined requirements early in the design process, a thorough detailed design package, and effective communication with both the customer and the fabrication contractors.

Tests Performed on Hydraulic Turbines at Commissioning or after Capital Repairs. Part II. Tests Performed on a 6.5 MW Kaplan Turbine

Directory of Open Access Journals (Sweden)

Adrian Cuzmoş

2015-07-01

Full Text Available The paper presents the tests performed on a hydraulic turbine on commissioning, the devices, test methods and the results obtained from the respective tests, as well as the conclusions and recommendations resulted from these tests. This kind of tests can be performed for the verification of guarantees.

Performance testing of extremity dosimeters, Study 2

International Nuclear Information System (INIS)

Harty, R.; Reece, W.D.; Hooker, C.D.

1990-04-01

The Health Physics Society Standards Committee (HPSSC) Working Group on Performance Testing of Extremity Dosimeters has issued a draft of a proposed standard for extremity dosimeters. The draft standard proposes methods to be used for testing dosimetry systems that determine occupational radiation dose to the extremities and the performance criterion used to determine compliance with the standard. Pacific Northwest Laboratory (PNL) has conducted two separate evaluations of the performance of extremity dosimeter processors to determine the appropriateness of the draft standard, as well as to obtain information regarding the performance of extremity dosimeters. Based on the information obtained during the facility visits and the results obtained from the performance testing, it was recommended that changes be made to ensure that the draft standard is appropriate for extremity dosimeters. The changes include: subdividing the mixture category and the beta particle category; eliminating the neutron category until appropriate flux-to-dose equivalent conversion factors are derived; and changing the tolerance level for the performance criterion to provide consistency with the performance criterion for whole body dosimeters, and to avoid making the draft standard overly difficult for processors of extremity dosimeters to pass. 20 refs., 10 figs., 6 tabs

The Effects of Humor on Test Anxiety and Test Performance

Science.gov (United States)

Tali, Glenda

2017-01-01

Testing in an academic setting provokes anxiety in all students in higher education, particularly nursing students. When students experience high levels of anxiety, the resulting decline in test performance often does not represent an accurate assessment of students' academic achievement. This quantitative, experimental study examined the effects…

Compressible Fluid Suspension Performance Testing

National Research Council Canada - National Science Library

Hoogterp, Francis

2003-01-01

... compressible fluid suspension system that was designed and installed on the vehicle by DTI. The purpose of the tests was to evaluate the possible performance benefits of the compressible fluid suspension system...

A financial analysis of revision hip arthroplasty: the economic burden in relation to the national tariff.

Science.gov (United States)

Vanhegan, I S; Malik, A K; Jayakumar, P; Ul Islam, S; Haddad, F S

2012-05-01

Revision arthroplasty of the hip is expensive owing to the increased cost of pre-operative investigations, surgical implants and instrumentation, protracted hospital stay and drugs. We compared the costs of performing this surgery for aseptic loosening, dislocation, deep infection and peri-prosthetic fracture. Clinical, demographic and economic data were obtained for 305 consecutive revision total hip replacements in 286 patients performed at a tertiary referral centre between 1999 and 2008. The mean total costs for revision surgery in aseptic cases (n = 194) were £11 897 (sd 4629), for septic revision (n = 76) £21 937 (sd 10 965), for peri-prosthetic fracture (n = 24) £18 185 (sd 9124), and for dislocation (n = 11) £10 893 (sd 5476). Surgery for deep infection and peri-prosthetic fracture was associated with longer operating times, increased blood loss and an increase in complications compared to revisions for aseptic loosening. Total inpatient stay was also significantly longer on average (p < 0.001). Financial costs vary significantly by indication, which is not reflected in current National Health Service tariffs.

Work zone performance measures pilot test.

Science.gov (United States)

2011-04-01

Currently, a well-defined and validated set of metrics to use in monitoring work zone performance do not : exist. This pilot test was conducted to assist state DOTs in identifying what work zone performance : measures can and should be targeted, what...

Optimizing the performance of the amphipod, Hyalella azteca, in chronic toxicity tests: Results of feeding studies with various foods and feeding regimes

Science.gov (United States)

The freshwater amphipod, Hyalella azteca, is a common organism used for sediment toxicity testing. Standard methods for 10-d and 42-d sediment toxicity tests with H. azteca were last revised and published by USEPA/ASTM in 2000. While Hyalella azteca methods exist for sediment tox...

Validation of a clinical critical thinking skills test in nursing

OpenAIRE

Shin, Sujin; Jung, Dukyoo; Kim, Sungeun

2015-01-01

Purpose: The purpose of this study was to develop a revised version of the clinical critical thinking skills test (CCTS) and to subsequently validate its performance. Methods: This study is a secondary analysis of the CCTS. Data were obtained from a convenience sample of 284 college students in June 2011. Thirty items were analyzed using item response theory and test reliability was assessed. Test-retest reliability was measured using the results of 20 nursing college and graduate school stud...

Dimensionality Analyses of the "GRE"® revised General Test Verbal and Quantitative Measures. ETS GRE® Board Research Report. ETS GRE®-16-02. ETS Research Report. RR-16-20

Science.gov (United States)

Robin, Frédéric; Bejar, Isaac; Liang, Longjuan; Rijmen, Frank

2016-01-01

Exploratory and confirmatory factor analyses of domestic data from the" GRE"® revised General Test, introduced in 2011, were conducted separately for the verbal (VBL) and quantitative (QNT) reasoning measures to evaluate the unidimensionality and local independence assumptions required by item response theory (IRT). Results based on data…

Description of the rates, trends and surgical burden associated with revision for prosthetic joint infection following primary and revision knee replacements in England and Wales: an analysis of the National Joint Registry for England, Wales, Northern Ireland and the Isle of Man.

Science.gov (United States)

Lenguerrand, Erik; Whitehouse, Michael R; Beswick, Andrew D; Toms, Andrew D; Porter, Martyn L; Blom, Ashley W

2017-07-10

To describe the prevalence rates of revision surgery for the treatment of prosthetic joint infection (PJI) for patients undergoing knee replacement, their time trends, the cumulative incidence function of revision for PJI and estimate the burden of PJI at health service level. We analysed revision knee replacements performed due to a diagnosis of PJI and the linked index procedures recorded in the National Joint Registry from 2003 to 2014 for England and Wales. The cohort analysed consisted of 679 010 index primary knee replacements, 33 920 index revision knee replacements and 8247 revision total knee replacements performed due to a diagnosis of PJI. The prevalence rates, their time trends investigated by time from index surgery to revision for PJI, cumulative incidence functions and the burden of PJI (total procedures) were calculated. Overall linear trends were investigated with log-linear regression. The incidence of revision total knee replacement due to PJI at 2 years was 3.2/1000 following primary and 14.4/1000 following revision knee replacement, respectively. The prevalence of revision due to PJI in the 3 months following primary knee replacement has risen by 2.5-fold (95% CI 1.2 to 5.3) from 2005 to 2013 and 7.5-fold (95% CI 1.0 to 56.1) following revision knee replacement. Over 1000 procedures per year are performed as a consequence of knee PJI, an increase of 2.8 from 2005 to 2013. Overall, 75% of revisions were two-stage with an increase in use of single-stage from 7.9% in 2005 to 18.8% in 2014. Although the risk of revision due to PJI following knee replacement is low, it is rising, and coupled with the established and further predicted increased incidence of both primary and revision knee replacements, this represents an increasing and substantial treatment burden for orthopaedic service delivery in England and Wales. This has implications for future service design and the funding of individual and specialist centres. © Article author

Performance Prediction of Centrifugal Compressor for Drop-In Testing Using Low Global Warming Potential Alternative Refrigerants and Performance Test Codes

Directory of Open Access Journals (Sweden)

Joo Hoon Park

2017-12-01

Full Text Available As environmental regulations to stall global warming are strengthened around the world, studies using newly developed low global warming potential (GWP alternative refrigerants are increasing. In this study, substitute refrigerants, R-1234ze (E and R-1233zd (E, were used in the centrifugal compressor of an R-134a 2-stage centrifugal chiller with a fixed rotational speed. Performance predictions and thermodynamic analyses of the centrifugal compressor for drop-in testing were performed. A performance prediction method based on the existing ASME PTC-10 performance test code was proposed. The proposed method yielded the expected operating area and operating point of the centrifugal compressor with alternative refrigerants. The thermodynamic performance of the first and second stages of the centrifugal compressor was calculated as the polytropic state. To verify the suitability of the proposed method, the drop-in test results of the two alternative refrigerants were compared. The predicted operating range based on the permissible deviation of ASME PTC-10 confirmed that the temperature difference was very small at the same efficiency. Because the drop-in test of R-1234ze (E was performed within the expected operating range, the centrifugal compressor using R-1234ze (E is considered well predicted. However, the predictions of the operating point and operating range of R-1233zd (E were lower than those of the drop-in test. The proposed performance prediction method will assist in understanding thermodynamic performance at the expected operating point and operating area of a centrifugal compressor using alternative gases based on limited design and structure information.

TMACS test procedure TP005: Sensor configuration, logging, and data conversion. Revision 4

International Nuclear Information System (INIS)

Washburn, S.J.

1994-01-01

The TMACS Software Project Test Procedures translate the project's acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the sensor configuration, conversion and logging requirements of the TMACS. The features to be tested are as follows: sensor configuration data; conversion of continuous sensor data to engineering units; conversion of digital data to discrete states; discrete sensor data logging; and continuous sensor data logging

User`s guide for the irradiation of experiments in the FTR. Revision 3

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-07-01

This document provides Revision 3 updates the FTR Users Guide. Revision 3 updates Appendix 1 (FFTF Technical Specifications) to include the following: Documentation of the acceptability of handling metal fuel assemblies in the Closed Loop Ex-Vessel Handling Machine (CLEM) and storing them in the Interim Decay Storage (IDS) vessel. Reactivity limit version (utilizing existing FSAR analysis bounds) to allow for the larger beta-effective associated with the addition of enriched uranium metal and oxide experiments to the core. Operational temperature limits for Open Test Assemblies (OTAs) have been expanded to differentiate between 40-foot experiment test articles, 28-foot Post Irradiation Open Test Assemblies (PIOTAs) and the 28-foot Loose Parts Monitor Assemblies (LMPAs) operating under FFTF core Engineering cognizance.

Extended Leach Testing of Simulated LAW Cast Stone Monoliths

Energy Technology Data Exchange (ETDEWEB)

Serne, R. Jeffrey [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lanigan, David C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Westsik, Joseph H. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Williams, Benjamin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jung, H. B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Guohui [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-08-12

This revision to the original report adds two longer term leach sets of data to the report and provides more discussion and graphics on how to interpret the results from long-term laboratory leach tests. The leach tests were performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate the release of key constituents from monoliths of Cast Stone prepared with four simulated low-activity waste (LAW) liquid waste streams.

Economic analysis of two-stage septic revision after total hip arthroplasty: What are the relevant costs for the hospital's orthopedic department?

Science.gov (United States)

Kasch, R; Assmann, G; Merk, S; Barz, T; Melloh, M; Hofer, A; Merk, H; Flessa, S

2016-03-01

The number of septic total hip arthroplasty (THA) revisions is increasing continuously, placing a growing financial burden on hospitals. Orthopedic departments performing septic THA revisions have no basis for decision making regarding resource allocation as the costs of this procedure for the departments are unknown. It is widely assumed that septic THA procedures can only be performed at a loss for the department. Therefore, the purpose of this study was to investigate whether this assumption is true by performing a detailed analysis of the costs and revenues for two-stage septic THA revision. Patients who underwent revision THA for septic loosening in two sessions from January 2009 through March 2012 were included in this retrospective, consecutive cost study from the orthopedic department's point of view. We analyzed variable and case-fixed costs for septic revision THA with special regard to implantation and explantation stay. By using marginal costing approach we neglected hospital-fixed costs. Outcome measures include reimbursement and daily contribution margins. The average direct costs (reimbursement) incurred for septic two-stage revision THA was €10,828 (€24,201). The difference in cost and contribution margins per day was significant (p cost for septic revision THA performed in two sessions. Disregarding hospital-fixed costs the included variable and case fixed-costs were covered by revenues. This study provides cost data, which will be guidance for health care decision makers.

Nuclear Regulatory Commission Human Factors Program Plan. Revision 2

International Nuclear Information System (INIS)

1986-04-01

This document is the Second Annual Revision to the NRC Human Factors Program Plan. The first edition was published in August 1983. Revision 1 was published in July of 1984. Purpose of the NRC Human Factors Program is to ensure that proper consideration is given to human factors in the design and operation of nuclear power plants. This document describes the plans of the Office of Nuclear Reactor Regulation to address high priority human factors concerns of importance to reactor safety in FY 1986 and FY 1987. Revision 2 of the plan incorporates recent Commission decisions and policies bearing on the human factors aspects of reactor safety regulation. With a few exceptions, the principal changes from prior editions reflect a shift from developing new requirements to staff evaluation of industry progress in resolving human factors issues. The plan addresses seven major program elements: (1) Training, (2) Licensing Examinations, (3) Procedures, (4) Man-Machine Interface, (5) Staffing and Qualifications, (6) Management and Organization, and (7) Human Performance

Maintenance Plan for the Performance Assessments and Composite Analyses of the Area 3 and Area 5 Radioactive Waste Management Sites at the Nevada Test Site

International Nuclear Information System (INIS)

Vefa Yucel

2007-01-01

U.S. Department of Energy (DOE) Manual M 435.1-1 requires that performance assessments (PAs) and composite analyses (CAs) for low-level waste (LLW) disposal facilities be maintained by the field offices. This plan describes the activities performed to maintain the PA and the CA for the Area 3 and Area 5 Radioactive Waste Management Sites (RWMSs) at the Nevada Test Site (NTS). This plan supersedes the Maintenance Plan for the Performance Assessments and Composite Analyses for the Area 3 and Area 5 Radioactive Waste Management Sites at the Nevada Test Site (DOE/NV/11718--491-REV 1, dated September 2002). The plan is based on U.S. Department of Energy (DOE) Order 435.1 (DOE, 1999a), DOE Manual M 435.1-1 (DOE, 1999b), the DOE M 435.1-1 Implementation Guide DOE G 435.1-1 (DOE, 1999c), and the Maintenance Guide for PAs and CAs (DOE, 1999d). The plan includes a current update on PA/CA documentation, a revised schedule, and a section on Quality Assurance

Correlation Between Screening Mammography Interpretive Performance on a Test Set and Performance in Clinical Practice.

Science.gov (United States)

Miglioretti, Diana L; Ichikawa, Laura; Smith, Robert A; Buist, Diana S M; Carney, Patricia A; Geller, Berta; Monsees, Barbara; Onega, Tracy; Rosenberg, Robert; Sickles, Edward A; Yankaskas, Bonnie C; Kerlikowske, Karla

2017-10-01

Evidence is inconsistent about whether radiologists' interpretive performance on a screening mammography test set reflects their performance in clinical practice. This study aimed to estimate the correlation between test set and clinical performance and determine if the correlation is influenced by cancer prevalence or lesion difficulty in the test set. This institutional review board-approved study randomized 83 radiologists from six Breast Cancer Surveillance Consortium registries to assess one of four test sets of 109 screening mammograms each; 48 radiologists completed a fifth test set of 110 mammograms 2 years later. Test sets differed in number of cancer cases and difficulty of lesion detection. Test set sensitivity and specificity were estimated using woman-level and breast-level recall with cancer status and expert opinion as gold standards. Clinical performance was estimated using women-level recall with cancer status as the gold standard. Spearman rank correlations between test set and clinical performance with 95% confidence intervals (CI) were estimated. For test sets with fewer cancers (N = 15) that were more difficult to detect, correlations were weak to moderate for sensitivity (woman level = 0.46, 95% CI = 0.16, 0.69; breast level = 0.35, 95% CI = 0.03, 0.61) and weak for specificity (0.24, 95% CI = 0.01, 0.45) relative to expert recall. Correlations for test sets with more cancers (N = 30) were close to 0 and not statistically significant. Correlations between screening performance on a test set and performance in clinical practice are not strong. Test set performance more accurately reflects performance in clinical practice if cancer prevalence is low and lesions are challenging to detect. Copyright © 2017 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

48 CFR 15.307 - Proposal revisions.

Science.gov (United States)

2010-10-01

... AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 15.307 Proposal revisions. (a) If an... allow proposal revisions to clarify and document understandings reached during negotiations. At the... submit a final proposal revision. The contracting officer is required to establish a common cut-off date...

Revision and psychometric testing of the Incivility in Nursing Education (INE) survey: introducing the INE-R.

Science.gov (United States)

Clark, Cynthia M; Barbosa-Leiker, Celestina; Gill, Larecia Money; Nguyen, Danh

2015-06-01

Academic incivility is a serious challenge for nursing education, which needs to be empirically measured and fully addressed. A convenience sample of nursing faculty and students from 20 schools of nursing in the United States participated in a mixed-methods study to test the psychometric properties of the Incivility in Nursing Education-Revised (INE-R) Survey. A factor analysis and other reliability analyses support the use of the INE-R as a valid and reliable measurement of student and faculty perceptions of incivility in nursing education. The INE-R is a psychometrically sound instrument to measure faculty and student perceptions of incivility; to examine differences regarding levels of nursing education, program type, gender, age, and ethnicity; to compare perceptions of incivility between and among adjunct, clinical, teaching, and research faculty; and to conduct pre- and postassessments of the perceived levels of faculty and student incivility in nursing programs to inform evidence-based interventions. Copyright 2015, SLACK Incorporated.

Motivational deficits and cognitive test performance in schizophrenia.

Science.gov (United States)

Fervaha, Gagan; Zakzanis, Konstantine K; Foussias, George; Graff-Guerrero, Ariel; Agid, Ofer; Remington, Gary

2014-09-01

Motivational and cognitive deficits are core features of schizophrenia, both closely linked with functional outcomes. Although poor effort and decreased motivation are known to affect performance on cognitive tests, the extent of this relationship is unclear in patients with schizophrenia. To evaluate the association between intrinsic motivation and cognitive test performance in patients with schizophrenia. Cross-sectional and 6-month prospective follow-up study performed at 57 sites in the United States, including academic and community medical treatment centers, participating in the Clinical Antipsychotic Trials of Intervention Effectiveness study. The primary sample included 431 stable patients with a DSM-IV diagnosis of schizophrenia currently receiving a stable medication regimen. Cognitive performance and intrinsic motivation were evaluated using a comprehensive neuropsychological test battery and a derived measure from the Heinrichs-Carpenter Quality of Life Scale, respectively. Symptom severity and functional status were also assessed. The primary outcome variable was global neurocognition. Individual domains of cognition were also evaluated for their association with motivation. Level of intrinsic motivation was significantly and positively correlated with global cognitive test performance, a relationship that held for each domain of cognition evaluated (correlation range, 0.20-0.34; P motivation and cognitive performance also remained significant after controlling for antipsychotic dose (P motivation during the 6-month follow-up was also found to be significantly related to improvement in global cognitive performance (P motivation and cognitive performance and suggest that test performance is not purely a measure of ability. Future studies assessing cognition in patients with schizophrenia should consider potential moderating variables such as effort and motivation. Implications for the assessment and interpretation of cognitive impairment based on

Performance of smokeless gasoline fire test facility

International Nuclear Information System (INIS)

Griffin, J.F.; Watkins, R.A.

1978-01-01

Packaging for radioactive materials must perform satisfactorily when subjected to temperatures simulating an accident involving a fire. The new thermal test facility has proved to be a reliable method for satisfactorily performing the required test. The flame provides sufficient heat to assure that the test is valid, and the temperature can be controlled satisfactorily. Also, the air and water mist systems virtually eliminate any smoke and thereby exceed the local EPA requirements. The combination of the two systems provides an inexpensive, low maintenance technique for elimination of the smoke plume

Expectancy of an open-book test decreases performance on a delayed closed-book test.

Science.gov (United States)

Agarwal, Pooja K; Roediger, Henry L

2011-11-01

Two experiments examined the influence of practice with, and the expectancy of, open-book tests (students viewed studied material while taking the test) versus closed-book tests (students completed the test without viewing the studied material) on delayed retention and transfer. Using GRE materials specifically designed for open-book testing, participants studied passages and then took initial open- or closed-book tests. Open-book testing led to better initial performance than closed-book testing, but on a delayed criterial (closed-book) test both types of testing produced similar retention after a two-day delay in Experiment 1. In Experiment 2 participants were informed in advance about the type of delayed criterial test to expect (open- or closed-book). Expecting an open-book test (relative to a closed-book test) decreased participants' time spent studying and their delayed test performance on closed-book comprehension and transfer tests, demonstrating that test expectancy can influence long-term learning. Expectancy of open-book tests may impair long-term retention and transfer compared to closed-book tests, despite superior initial performance on open-book tests and students' preference for open-book tests.

Crianças com fissura isolada de palato: desempenho nos testes de processamento auditivo Cleft palate children: performance in auditory processing tests

Directory of Open Access Journals (Sweden)

Mirela Boscariol

2009-04-01

Full Text Available Muitas crianças com transtorno de processamento auditivo têm uma prevalência alta de otite média, alteração na orelha média de grande ocorrência na população com fissura labiopalatina. OBJETIVO: Verificar o desempenho de crianças com fissura isolada de palato (FP em testes do processamento auditivo. Estudo prospectivo. MATERIAL E MÉTODO: Vinte crianças (7 a 11 anos com FP foram submetidas aos testes de localização sonora (LS, memória para sons verbais (MSSV e não-verbais em seqüência (MSSNV, Fusão Auditiva-Revisado (AFT-R, Teste Pediátrico de Inteligibilidade de Fala/Sentenças Sintéticas (PSI/SSI, Dissílabos alternados (SSW e Dicótico de dígitos (DD. O desempenho das crianças nos testes foi classificado em ruim e bom. RESULTADOS: Não houve diferença estatística entre os gêneros e orelhas. Os valores médios obtidos foram 2,16, 2,42, 4,37, 60,50ms, de 40,71 a 67,33%, 96,25 a 99,38%, 73,55 a 73,88% e 58,38 a 65,47%, respectivamente, para os testes MSSNV, MSSV, LS, AFT-R, PSI/SSI com mensagem competitiva ipsilateral (PSI/SSIMCI e contralateral (PSI/SSI/MCC, DD e SSW. CONCLUSÃO: Uma alta porcentagem de crianças demonstrou seus piores desempenhos nos testes AFT-R, DD, SSW e no teste PSI/SSIMCI. Os melhores desempenhos ocorreram nos testes de localização sonora, memória seqüencial para sons não verbais e verbais e para PSI/SSIMCC.Many children with auditory processing disorders have a high prevalence of otitis media, a middle ear alterations greatly prevalent in children with palatine and lip clefts. AIM: to check the performance of children with palate cleft alone (PC in auditory processing tests. Prospective study. MATERIALS AND METHODS: twenty children (7 to 11 years with CP were submitted to sound location tests (SL, memory for verbal sounds (MSSV and non verbal sounds in sequence (MSSNV, Revised auditory fusion (AFT-R, Pediatric test of speech intelligibility/synthetic sentences (PSI/SSI, alternate

Preliminary Study on the Revision of Nuclear Safety Policy Statement

International Nuclear Information System (INIS)

Lee, Y. E.; Lee, S. H.; Chang, H. S.; Choi, K. S.; Jung, S. J.

2011-01-01

Nuclear safety policy in Korea is currently declared in the Nuclear Safety Charter as the highest tier document and safety principles and directions are announced in the Nuclear Safety Policy Statement. As the circumstances affecting on the nuclear safety policy change, it needs to revise the Statement. This study aims to develop the revised Nuclear Safety Policy Statement to declare that securing safety is a prerequisite to the utilization of nuclear energy, and that all workers in nuclear industry and regulatory body must adhere to the principle of priority to safety. As a result, two different types of revision are being prepared as of August. One is based on the spirit of Nuclear Safety Charter as well as the direction of future-oriented safety policies including the changes in the environment after declaration of the Statement. The other is to declare the fundamental safety objective and safety principles as the top philosophy of national nuclear safety policy by adopting the '10 Safety Principles in IAEA Safety Fundamental' instead of the current Charter. Both versions of revision are subject to further in-depth discussion. However once the revision is finalized and declared, it would be useful to accomplish effectively the organizational responsibilities and to enhance the public confidence in nuclear safety by performing the regulatory activities in a planned and systematic manner and promulgating the government's dedication to priority to safety

Enhancement on Wingate Anaerobic Test Performance With Hyperventilation.

Science.gov (United States)

Leithäuser, Renate M; Böning, Dieter; Hütler, Matthias; Beneke, Ralph

2016-07-01

Relatively long-lasting metabolic alkalizing procedures such as bicarbonate ingestion have potential for improving performance in long-sprint to middle-distance events. Within a few minutes, hyperventilation can induce respiratory alkalosis. However, corresponding performance effects are missing or equivocal at best. To test a potential performance-enhancing effect of respiratory alkalosis in a 30-s Wingate Anaerobic Test (WAnT). 10 men (mean ± SD age 26.6 ± 4.9 y, height 184.4 ± 6.1 cm, body-mass test 1 80.7 ± 7.7 kg, body-mass test 2 80.4 ± 7.2 kg, peak oxygen uptake 3.95 ± 0.43 L/min) performed 2 WAnTs, 1 with and 1 without a standardized 15-min hyperventilation program pre-WAnT in randomized order separated by 1 wk. Compared with the control condition, hyperventilation reduced (all P respiratory alkalosis can enhance WAnT cycling sprint performance well in the magnitude of what is seen after successful bicarbonate ingestion.

7 CFR 3015.115 - Budget revisions.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Budget revisions. 3015.115 Section 3015.115..., DEPARTMENT OF AGRICULTURE UNIFORM FEDERAL ASSISTANCE REGULATIONS Programmatic Changes and Budget Revisions § 3015.115 Budget revisions. (a) Nonconstruction projects. (1) Except as provided in paragraph (a)(2) of...

Performance and treatment outcome of tuberculosis among patients on Revised National Tuberculosis Control Programme in Urban and Tribal areas of a district in Maharashtra

Directory of Open Access Journals (Sweden)

Shivshakti Dattatray Pawar

2017-01-01

Full Text Available Background: Revised National Tuberculosis Control Programme (RNTCP was introduced in the country as a pilot project since 1993 in a phased manner and expanded throughout the country by the year 2005. Although studies have shown the success of RNTCP, data pertaining to the indicators of programme performance in urban and tribal set up are rare. Objectives: The objective of this study was to assess and compare the RNTCP in urban and tribal areas of Maharashtra through the indicators of performance and outcome of the patients. Patients and Methods: A retrospective comparative record-based study was conducted in selected urban and tribal areas' tuberculosis (TB units. Records of patients enrolled newly for TB treatment and those already undergoing treatment under RNTCP from April 2015 to September 2015 (6 months were considered for analysis. Chi-square test and Z-test (test of significance are applied where required by using Epi Info 7 and Microsoft Excel 2010.Results: Sputum smear collection was significantly higher in urban areas (P = 0.001. In urban areas, new TB case detection was 35%, while in tribal areas, it was 42% as per the RNTCP norms. Sputum positivity was marginally more in tribal (5.87% than urban (3.28% areas. Cure rate was more in urban areas than tribal (P = 0.001 areas. There were statistically significantly high default cases in tribal areas. Conclusions: Sputum collection and sputum positivity rate were low in urban and tribal areas, but TB screening, especially in tribal areas, was significantly low. Sputum positivity was significantly higher in tribal areas. Significantly low cure rate and high default rate in tribal area warrant the need for strengthening of RNTCP activities in tribal areas.

Motivation and Test Anxiety in Test Performance across Three Testing Contexts: The CAEL, CET, and GEPT

Science.gov (United States)

Cheng, Liying; Klinger, Don; Fox, Janna; Doe, Christine; Jin, Yan; Wu, Jessica

2014-01-01

This study examined test-takers' motivation, test anxiety, and test performance across a range of social and educational contexts in three high-stakes language tests: the Canadian Academic English Language (CAEL) Assessment in Canada, the College English Test (CET) in the People's Republic of China, and the General English Proficiency Test (GEPT)…

Summary of functional and performance test procedures

DEFF Research Database (Denmark)

Mitzel, Jens; Gülzow, Erich; Friedrich, K. Andreas

Different Test Modules (TM) are defined for the functional and performance characterization of a PEMFC stack. The master document TM2.00 defines requirements and methodology for parameter variation, stability and data acquisition.......Different Test Modules (TM) are defined for the functional and performance characterization of a PEMFC stack. The master document TM2.00 defines requirements and methodology for parameter variation, stability and data acquisition....

Applying computerized adaptive testing to the Negative Acts Questionnaire-Revised: Rasch analysis of workplace bullying.

Science.gov (United States)

Ma, Shu-Ching; Chien, Tsair-Wei; Wang, Hsiu-Hung; Li, Yu-Chi; Yui, Mei-Shu

2014-02-17

Workplace bullying is a prevalent problem in contemporary work places that has adverse effects on both the victims of bullying and organizations. With the rapid development of computer technology in recent years, there is an urgent need to prove whether item response theory-based computerized adaptive testing (CAT) can be applied to measure exposure to workplace bullying. The purpose of this study was to evaluate the relative efficiency and measurement precision of a CAT-based test for hospital nurses compared to traditional nonadaptive testing (NAT). Under the preliminary conditions of a single domain derived from the scale, a CAT module bullying scale model with polytomously scored items is provided as an example for evaluation purposes. A total of 300 nurses were recruited and responded to the 22-item Negative Acts Questionnaire-Revised (NAQ-R). All NAT (or CAT-selected) items were calibrated with the Rasch rating scale model and all respondents were randomly selected for a comparison of the advantages of CAT and NAT in efficiency and precision by paired t tests and the area under the receiver operating characteristic curve (AUROC). The NAQ-R is a unidimensional construct that can be applied to measure exposure to workplace bullying through CAT-based administration. Nursing measures derived from both tests (CAT and NAT) were highly correlated (r=.97) and their measurement precisions were not statistically different (P=.49) as expected. CAT required fewer items than NAT (an efficiency gain of 32%), suggesting a reduced burden for respondents. There were significant differences in work tenure between the 2 groups (bullied and nonbullied) at a cutoff point of 6 years at 1 worksite. An AUROC of 0.75 (95% CI 0.68-0.79) with logits greater than -4.2 (or >30 in summation) was defined as being highly likely bullied in a workplace. With CAT-based administration of the NAQ-R for nurses, their burden was substantially reduced without compromising measurement precision.

Belief revision and delusions: how do patients with schizophrenia take advice?

Science.gov (United States)

Kaliuzhna, Mariia; Chambon, Valérian; Franck, Nicolas; Testud, Bérangère; Van der Henst, Jean-Baptiste

2012-01-01

The dominant cognitive model that accounts for the persistence of delusional beliefs in schizophrenia postulates that patients suffer from a general deficit in belief revision. It is generally assumed that this deficit is a consequence of impaired reasoning skills. However, the possibility that such inflexibility affects the entire system of a patient's beliefs has rarely been empirically tested. Using delusion-neutral material in a well-documented advice-taking task, the present study reports that patients with schizophrenia: 1) revise their beliefs, 2) take into account socially provided information to do so, 3) are not overconfident about their judgments, and 4) show less egocentric advice-discounting than controls. This study thus shows that delusional patients' difficulty in revising beliefs is more selective than had been previously assumed. The specificities of the task and the implications for a theory of delusion formation are discussed.

Irradiation test and performance evaluation of DUPIC fuel

International Nuclear Information System (INIS)

Yang, Myung Seung; Song, K. C.; Moon, J. S.

2002-05-01

The objective of the project is to establish the performance evaluation system of DUPIC fuel during the Phase II R and D. In order to fulfil this objectives, irradiation test of DUPIC fuel was carried out in HANARO using the non-instrumented and SPND-instrumented rig. Also, the analysis on the in-reactor behavior analysis of DUPIC fuel, out-pile test using simulated DUPIC fuel as well as performance and integrity assessment in a commercial reactor were performed during this Phase. The R and D results of the Phase II are summarized as follows : - Performance evaluation of DUPIC fuel via irradiation test in HANARO - Post irradiation examination of irradiated fuel and performance analysis - Development of DUPIC fuel performance code (modified ELESTRES) considering material properties of DUPIC fuel - Irradiation behavior and integrity assessment under the design power envelope of DUPIC fuel - Foundamental technology development of thermal/mechanical performance evaluation using ANSYS (FEM package)

High School Students' Performance on Vandenberg's Mental Rotations Test: Art Ability, Gender, Activities, Academic Performance, Strategies, and Ease of Taking the Test.

Science.gov (United States)

Gurny, Helen Graham

This study tested whether mental rotation performance of 186 high school students (80 males and 106 females) in grades 9 through 12 in art and nonart classes on Vandenbergs Mental Rotations test (S. Vandenberg and Kuse, 1978) was affected by gender, visual-spatial activities, strategies used while performing the test, and the ease of test taking.…

Revised experimental program on the nuclear ship 'Mutsu'

International Nuclear Information System (INIS)

Mori, Yuichi

1985-01-01

The experimental program on the nuclear ship ''Mutsu'' has been revised by the Government. And, the responsible organization for n. s. Mutsu was turned to Japan Atomic Energy Research Institute (JAERI) from Japan Nuclear-ship Development Agency. The revised, new experimental program is as follows. (1) Experimental navigation of n. s. Mutsu is made with the already loaded 1st reactor core for about one year. (2) The mooring port for n. s. Mutsu is in a minimum scale. (3) Upon termination of the experimental navigation, n. s. Mutsu is immediately decommissioned. (4) Power-up test and experimental navigation of n. s. Mutsu are made in fiscal 1989 to 1990. The policy of research and development with n. s. Mutsu and the works assigned to JAERI with n. s. Mutsu are described. (Mori, K.)

A randomized controlled pilot trial comparing the impact of access to clinical endocrinology video demonstrations with access to usual revision resources on medical student performance of clinical endocrinology skills.

Science.gov (United States)

Hibbert, Emily J; Lambert, Tim; Carter, John N; Learoyd, Diana L; Twigg, Stephen; Clarke, Stephen

2013-10-03

Demonstrating competence in clinical skills is key to course completion for medical students. Methods of providing clinical instruction that foster immediate learning and potentially serve as longer-term repositories for on-demand revision, such as online videos demonstrating competent performance of clinical skills, are increasingly being used. However, their impact on learning has been little studied. The aim of this study was to determine the value of adjunctive on-demand video-based training for clinical skills acquisition by medical students in endocrinology. Following an endocrinology clinical tutorial program, 2nd year medical students in the pre-assessment revision period were recruited and randomized to either a set of bespoke on-line clinical skills training videos (TV), or to revision as usual (RAU). The skills demonstrated on video were history taking in diabetes mellitus (DMH), examination for diabetes lower limb complications (LLE), and examination for signs of thyroid disease (TE). Students were assessed on these clinical skills in an observed structured clinical examination two weeks after randomization. Assessors were blinded to student randomization status. For both diabetes related clinical skills assessment tasks, students in the TV group performed significantly better than those in the RAU group. There were no between group differences in thyroid examination performance. For the LLE, 91.7% (n = 11/12) of students randomized to the video were rated globally as competent at the skill compared with 40% (n = 4/10) of students not randomized to the video (p = 0.024). For the DMH, 83.3% (n = 10/12) of students randomized to the video were rated globally as competent at the skill compared with 20% (n = 2/10) of students not randomized to the video (p = 0.007). Exposure to high quality videos demonstrating clinical skills can significantly improve medical student skill performance in an observed structured clinical examination of these skills, when

NNWSI waste form performance test development

International Nuclear Information System (INIS)

Bates, J.K.; Gerding, T.J.

1984-01-01

A test method has been developed to measure the release of radionuclides from the waste package under simulated NNWSI repository conditions, and to provide information concerning materials interactions that may occur in the repository. Data from 13 weeks of unsaturated testing are discussed and compared to that from a 13-week analog test. The data indicate that the waste form test is capable of producing consistent, reproducible results that will be useful in evaluating the role of the waste in the long-term performance of the repository. 6 references, 3 figures

Single-stage Acetabular Revision During Two-stage THA Revision for Infection is Effective in Selected Patients.

Science.gov (United States)

Fink, Bernd; Schlumberger, Michael; Oremek, Damian

2017-08-01

The treatment of periprosthetic infections of hip arthroplasties typically involves use of either a single- or two-stage (with implantation of a temporary spacer) revision surgery. In patients with severe acetabular bone deficiencies, either already present or after component removal, spacers cannot be safely implanted. In such hips where it is impossible to use spacers and yet a two-stage revision of the prosthetic stem is recommended, we have combined a two-stage revision of the stem with a single revision of the cup. To our knowledge, this approach has not been reported before. (1) What proportion of patients treated with single-stage acetabular reconstruction as part of a two-stage revision for an infected THA remain free from infection at 2 or more years? (2) What are the Harris hip scores after the first stage and at 2 years or more after the definitive reimplantation? Between June 2009 and June 2014, we treated all patients undergoing surgical treatment for an infected THA using a single-stage acetabular revision as part of a two-stage THA exchange if the acetabular defect classification was Paprosky Types 2B, 2C, 3A, 3B, or pelvic discontinuity and a two-stage procedure was preferred for the femur. The procedure included removal of all components, joint débridement, definitive acetabular reconstruction (with a cage to bridge the defect, and a cemented socket), and a temporary cemented femoral component at the first stage; the second stage consisted of repeat joint and femoral débridement and exchange of the femoral component to a cementless device. During the period noted, 35 patients met those definitions and were treated with this approach. No patients were lost to followup before 2 years; mean followup was 42 months (range, 24-84 months). The clinical evaluation was performed with the Harris hip scores and resolution of infection was assessed by the absence of clinical signs of infection and a C-reactive protein level less than 10 mg/L. All

In Situ Field Testing of Processes

Energy Technology Data Exchange (ETDEWEB)

J. Wang

2001-12-14

The purpose of this Analysis/Model Report (AMR) is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts of the Yucca Mountain Site Characterization Project (YMP). This revision updates data and analyses presented in the initial issue of this AMR. This AMR was developed in accordance with the ''Technical Work Plan for Unsaturated Zone (UZ) Flow and Transport Process Model Report'' and ''Technical Work Plan for UZ Flow, Transport, and Coupled Processes Process Model Report. These activities were performed to investigate in situ flow and transport processes. The evaluations provide the necessary framework to: (1) refine and confirm the conceptual model of matrix and fracture processes in the unsaturated zone (UZ) and (2) analyze the impact of excavation (including use of construction water and effect of ventilation) on the UZ flow and transport processes. This AMR is intended to support revisions to ''Conceptual and Numerical Models for UZ Flow and Transport'' and ''Unsaturated Zone Flow and Transport Model Process Model Report''. In general, the results discussed in this AMR are from studies conducted using a combination or a subset of the following three approaches: (1) air-injection tests, (2) liquid-release tests, and (3) moisture monitoring using in-drift sensors or in-borehole sensors, to evaluate the impact of excavation, ventilation, and construction-water usage on the surrounding rocks. The liquid-release tests and air-injection tests provide an evaluation of in situ fracture flow and the competing processes of matrix imbibition. Only the findings from testing and data not covered in the ''Seepage Calibration Model and Seepage Testing Data'' are analyzed in detail in the AMR.

IN SITU FIELD TESTING OF PROCESSES

Energy Technology Data Exchange (ETDEWEB)

J.S.Y. YANG

2004-11-08

The purpose of this scientific analysis report is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts and surface-based boreholes through unsaturated zone (UZ) tuff rock units. In situ testing, monitoring, and associated laboratory studies are conducted to directly assess and evaluate the waste emplacement environment and the natural barriers to radionuclide transport at Yucca Mountain. This scientific analysis report supports and provides data to UZ flow and transport model reports, which in turn contribute to the Total System Performance Assessment (TSPA) of Yucca Mountain, an important document for the license application (LA). The objectives of ambient field-testing activities are described in Section 1.1. This report is the third revision (REV 03), which supercedes REV 02. The scientific analysis of data for inputs to model calibration and validation as documented in REV 02 were developed in accordance with the Technical Work Plan (TWP) ''Technical Work Plan for: Performance Assessment Unsaturated Zone'' (BSC 2004 [DIRS 167969]). This revision was developed in accordance with the ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654], Section 1.2.4) for better integrated, consistent, transparent, traceable, and more complete documentation in this scientific analysis report and associated UZ flow and transport model reports. No additional testing or analyses were performed as part of this revision. The list of relevant acceptance criteria is provided by ''Technical Work Plan for: Unsaturated Zone Flow Analysis and Model Report Integration'' (BSC 2004 [DIRS 169654]), Table 3-1. Additional deviations from the TWP regarding the features, events, and processes (FEPs) list are discussed in Section 1.3. Documentation in this report includes descriptions of how, and under what

Evaluation of the revised training program for senior control room staff: science fundamentals and equipment principles

International Nuclear Information System (INIS)

Jervis, R.E.; Evans, G.J.

1996-10-01

Canadian nuclear utilities have formed an Inter-Utility Working Group to revise their program for training nuclear generating station senior control room staff, namely Control Room Operators and Shift Supervisors, in Science Fundamentals and Equipment Principles. This report documents the findings of an external review of this revision process, addressing, amongst other topics, the process of revision undertaken by the Working Group, their outline of topics to be included, and, the pertinence and comprehensiveness of the detailed training objectives identified for two of the courses. The approach to revising the program being followed by the Working Group appears to be reasonable insomuch that some training needs have been identified and used to construct detailed sets of training objectives. However, as assessed by the consultants without full documentation being available, some important steps appear to have been missed. Specifically, much of the basis of the revision process has not been documented, neither has the approach selected for the revision process, nor has any justification for not performing a CANDU specific job and task analysis been offered. Furthermore, the Working Group has not yet proposed any criteria for evaluation of the program or provided any test items. As a result, the consultants have had to develop criteria for evaluation of the overall program and of individual courses. These criteria were applied in a more detailed review of the training objectives for two particular courses: Plant Chemistry, and Nuclear Physics and Reactor Theory. Many of the training objectives for these courses were found to be too qualitative or ones that require trainees to memorize blocks of information rather than develop in them an ability to arrive at conclusions about scientific phenomena using principles and reasoning. This assessment indicates that the training objectives are designed to achieve too low a level of cognition, inconsistent with developing an

Factors affecting the auction price of Veldram performance tested ...

African Journals Online (AJOL)

The popularity of these auctions for performance tested rams (89.4 % of rams sold) indicate that Veld tested rams were sought after by buyers. The sale price of 296 Veld tested Dorper rams sold between 1994 and 2001, covering seven different tests, were compared with their measured and observed performances.

Phase I Hydrologic Data for the Groundwater Flow and Contaminant Transport Model of Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nye County, Nevada, Revision 0

International Nuclear Information System (INIS)

John McCord

2007-01-01

This document, which makes changes to Phase I Hydrologic Data for the Groundwater Flow and Contaminant Transport Model of Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nye County, Nevada, S-N/99205--077, Revision 0 (June 2006), was prepared to address review comments on this final document provided by the Nevada Division of Environmental Protection (NDEP) in a letter dated August 4, 2006. The document includes revised pages that address NDEP review comments and comments from other document users. Change bars are included on these pages to identify where the text was revised. In addition to the revised pages, the following clarifications are made for the two plates inserted in the back of the document: Plate 4: Disregard the repeat of legend text 'Drill Hole Name' and 'Drill Hole Location' in the lower left corner of the map. Plate 6: The symbol at the ER-16-1 location (white dot on the lower left side of the map) is not color-coded because no water level has been determined. The well location is included for reference. Plate 6: The symbol at the ER-12-1 location (upper left corner of the map), a yellow dot, represents the lower water level elevation. The higher water level elevation, represented by a red dot, was overprinted

24 CFR 968.225 - Budget revisions.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Budget revisions. 968.225 Section... Fewer Than 250 Units) § 968.225 Budget revisions. (a) A PHA shall not incur any modernization cost in excess of the total HUD-approved CIAP budget. A PHA shall submit a budget revision, in a form prescribed...

Beam test performance of the SKIROC2 ASIC

CERN Document Server

Frisson, T; Anduze, M; Augustin, J.E; Bonis, J; Boudry, V; Bourgeois, C; Brient, J.C; Callier, S; Cerutti, M; Chen, S; Cornat, R; Cornebise, P; Cuisy, D; David, J; De la Taille, C; Dulucq, F; Frotin, M; Gastaldi, F; Ghislain, P; Giraud, J; Gonnin, A; Grondin, D; Guliyev, E; Hostachy, J.Y; Jeans, D; Kamiya, Y; Kawagoe, K; Kozakai, C; Lacour, D; Lavergne, L; Lee, S.H; Magniette, F; Ono, H; Poeschl, R; Rouëné, J; Seguin-Moreau, N; Song, H.S; Sudo, Y; Thiebault, A; Tran, H; Ueno, H; Van der Kolk, N; Yoshioka, T

2015-01-01

Beam tests of the first layers of CALICE silicon tungsten ECAL technological prototype were performed in April and July 2012 using 1–6 GeV electron beam at DESY. This paper presents an analysis of the SKIROC2 readout ASIC performance under test beam conditions.

40 CFR 63.309 - Performance tests and procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Performance tests and procedures. 63.309 Section 63.309 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise...

Towards Smart Buildings Performance Testing as a Service

DEFF Research Database (Denmark)

Markoska, Elena; Lazarova-Molnar, Sanja

2018-01-01

to buildings’ energy consumption. In this paper we propose a methodology for continuous performance testing of smart buildings as a service. We discuss the automatic discovery and instantiation of performance tests, as well as usage of results for discovery of potential faults and ways to improve buldings...

Cognitive Fatigue Influences Students’ Performance on Standardized Tests

DEFF Research Database (Denmark)

Sievertsen, Hans Henrik; Gino, Francesca; Piovesan, Marco

2016-01-01

We identify one potential source of bias that influences children’s performance on standardized tests and that is predictable based on psychological theory: the time at which students take the test. Using test data for all children attending Danish public schools between school years 2009....../10 and 2012/13, we find that, for every hour later in the day, test scores decrease by 0.9% of an SD. In addition, a 20- to 30-minute break improves average test scores. Time of day affects students’ test performance because, over the course of a regular day, students’ mental resources get taxed. Thus......, as the day wears on, students become increasingly fatigued and consequently more likely to underperform on a standardized test....

Post-test analysis for the APR1400 LBLOCA DVI performance test using MARS

International Nuclear Information System (INIS)

Bae, Kyoo Hwan; Lee, Y. J.; Kim, H. C.; Bae, Y. Y.; Park, J. K.; Lee, W.

2002-03-01

Post-test analyses using a multi-dimensional best-estimate analysis code, MARS, are performed for the APR1400 LBLOCA DVI (Direct Vessel Injection) performance tests. This report describes the code evaluation results for the test data of various void height tests and direct bypass tests that have been performed at MIDAS test facility. MIDAS is a scaled test facility of APR1400 with the objective of identifying multi-dimensional thermal-hydraulic phenomena in the downcomer during the reflood conditions of a large break LOCA. A modified linear scale ratio was applied in its construction and test conditions. The major thermal-hydraulic parameters such as ECC bypass fraction, steam condensation fraction, and temperature distributions in downcomer are compared and evaluated. The evaluation results of MARS code for the various test cases show that: (a) MARS code has an advanced modeling capability of well predicting major multi-dimensional thermal-hydraulic phenomena occurring in the downcomer, (b) MARS code under-predicts the steam condensation rates, which in turn causes to over-predict the ECC bypass rates. However, the trend of decrease in steam condensation rate and increase in ECC bypass rate in accordance with the increase in steam flow rate, and the calculation results of the ECC bypass rates under the EM analysis conditions generally agree with the test data

Exploration of task performance tests in a physics laboratory

Science.gov (United States)

Liu, Dan; El Turkey, Houssein

2017-11-01

In this article, we investigate the implementation of task performance tests in an undergraduate physics laboratory. Two performance tests were carried out over two semesters using the task of building a DC circuit. The first implementation in Spring 2014 had certain concerns such as the privacy of students’ testing and their ‘trial and error’ attempts. These concerns were addressed in Fall 2015 through implementing a second performance test. The second implementation was administered differently but the content of the two tests was the same. We discuss the validity of both implementations and present the correlation (or lack of) between the time that students needed to complete the tests and their grades from a paper-based laboratory assessment method.

Measuring Attending Behavior and Short-Term Memory with Knox's Cube Test.

Science.gov (United States)

Stone, Mark H.; Wright, Benjamin D.

1983-01-01

A new revision was developed using Rasch psychometric techniques to build a Knox's Cube Test (KCT) variable and item bank using the tapping series from all previous editions. The report forms developed give a clear picture of the subject's performance set in a context that is both normative and criterion. (Author/BW)

Belief revision and delusions: how do patients with schizophrenia take advice?

Directory of Open Access Journals (Sweden)

Mariia Kaliuzhna

Full Text Available The dominant cognitive model that accounts for the persistence of delusional beliefs in schizophrenia postulates that patients suffer from a general deficit in belief revision. It is generally assumed that this deficit is a consequence of impaired reasoning skills. However, the possibility that such inflexibility affects the entire system of a patient's beliefs has rarely been empirically tested. Using delusion-neutral material in a well-documented advice-taking task, the present study reports that patients with schizophrenia: 1 revise their beliefs, 2 take into account socially provided information to do so, 3 are not overconfident about their judgments, and 4 show less egocentric advice-discounting than controls. This study thus shows that delusional patients' difficulty in revising beliefs is more selective than had been previously assumed. The specificities of the task and the implications for a theory of delusion formation are discussed.

Developing the Observatory Test of Capacity, Performance, and Developmental Disregard (OTCPDD for Children with Cerebral Palsy.

Directory of Open Access Journals (Sweden)

Kuan-Chun Liu

Full Text Available The purpose of this study was to develop a reliable and valid instrument, named the Observatory Test of Capacity, Performance, and Developmental Disregard (OTCPDD, for measuring the amount and quality of use of affected upper limb functions in the daily routines of children with CP.Forty-eight participants (24 children with CP and 24 matched typically developing children were recruited. The OTCPDD was administered twice (the spontaneous use condition first, followed by the forced use condition on children with CP. Their parents were asked to complete the Pediatric Motor Activity Log-Revised (PMAL-R. The internal consistency, the intrarater and interrater reliabilities, and the convergent and discriminate validities were measured.The internal consistency (Cronbach's alpha and the intrarater and interrater reliabilities were higher than 0.9 for all of the OTCPDD scores. The convergent validity was confirmed by significant correlations between the OTCPDD and the PMAL-R. For the discriminant validity, significant differences (p<0.05 were found between children with CP and typically developing children.The results support that the OTCPDD is a reliable and valid observation-based assessment. The OTCPDD, which uses bimanual daily living activities, is able to represent the children's general affected hand functions (including capacity, performance, and developmental disregard in their daily routines.

Appraising Pre-service EFL Teachers' Assessment in Language Testing Course Using Revised Bloom's Taxonomy

Directory of Open Access Journals (Sweden)

Elham Mohammadi

2015-07-01

Full Text Available The teachers need to be conceived as a “change agent” and not as a mere transmitter of knowledge and culture. In developing countries like Iran, one of the most significant concerns in the field of teachers’ education is efficiency of pre-service programs. To this aim, the current descriptive-evaluative study intended to describe the state of pre-service teachers' assessment in the field of language testing by (a examining the exam questions to find out whether they are aligned with curriculum objectives and syllabus (content validity, (b exploring whether they take care of higher order cognitive processes and (c finding what combinations of cognitive process levels and knowledge types in Revised Bloom's Taxonomy are prevalent in the questions. The results exhibited an unbalanced coverage of content in exams. Also the questions were found to be inadequate in terms of measuring complex cognitive skills (Analyze and Evaluate; Remember and Understand domains take up 91.6 % of all questions and no item was found for Create. Three combinations of cognitive process level and knowledge type was dominant in the data set: (1 Remember Factual Knowledge, (2 Understand Conceptual Knowledge, and (3 Apply Procedural Knowledge. These associations confirm the Anderson and Krathwohl's (2001 proposition.

40 CFR 63.2354 - What performance tests, design evaluations, and performance evaluations must I conduct?

Science.gov (United States)

2010-07-01

... evaluations, and performance evaluations must I conduct? 63.2354 Section 63.2354 Protection of Environment... tests, design evaluations, and performance evaluations must I conduct? (a)(1) For each performance test... procedures specified in subpart SS of this part. (3) For each performance evaluation of a continuous emission...

Model tests on dynamic performance of RC shear walls

International Nuclear Information System (INIS)

Nagashima, Toshio; Shibata, Akenori; Inoue, Norio; Muroi, Kazuo.

1991-01-01

For the inelastic dynamic response analysis of a reactor building subjected to earthquakes, it is essentially important to properly evaluate its restoring force characteristics under dynamic loading condition and its damping performance. Reinforced concrete shear walls are the main structural members of a reactor building, and dominate its seismic behavior. In order to obtain the basic information on the dynamic restoring force characteristics and damping performance of shear walls, the dynamic test using a large shaking table, static displacement control test and the pseudo-dynamic test on the models of a shear wall were conducted. In the dynamic test, four specimens were tested on a large shaking table. In the static test, four specimens were tested, and in the pseudo-dynamic test, three specimens were tested. These tests are outlined. The results of these tests were compared, placing emphasis on the restoring force characteristics and damping performance of the RC wall models. The strength was higher in the dynamic test models than in the static test models mainly due to the effect of loading rate. (K.I.)

Recommended aquifer grid resolution for E-Area PA revision transport simulations

Energy Technology Data Exchange (ETDEWEB)

Flach, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2018-01-03

This memorandum addresses portions of Section 3.5.2 of SRNL (2016) by recommending horizontal and vertical grid resolution for aquifer transport, in preparation for the next E-Area Performance Assessment (WSRC 2008) revision.

Tradução e adaptação para a cultura brasileira do "Nursing Work Index - Revised" Traducción y adaptación a la cultura brasileña del "Nursing Work Index - Revised" Translation and cross-cultural adaptation of the "Nursing Work Index - Revised" into Brazilian Portuguese

Directory of Open Access Journals (Sweden)

Renata Cristina Gasparino

2009-06-01

Full Text Available OBJETIVO: Traduzir e adaptar o "Nursing Work Index - Revised", para a cultura brasileira. MÉTODOS: Para o procedimento metodológico seguiram-se as etapas recomendadas internacionalmente: tradução; retro-tradução; avaliação por um grupo de juízes e pré-teste. RESULTADOS: As etapas de tradução e retro-tradução foram realizadas satisfatoriamente e a avaliação da versão síntese pelo comitê de juízes resultou em alteração na maioria dos itens assegurando as equivalências entre as versões original e traduzida. Durante o pré-teste, verificou-se a necessidade de reformulações de alguns itens tornando-os mais claros e de fácil compreensão. CONCLUSÃO: Destaca-se que apesar da complexidade do instrumento, o processo de tradução e adaptação cultural do Nursing Work Index - Revised, para a cultura brasileira, foi concluído com sucesso.OBJETIVO: Traducir y adaptar el "Nursing Work Index - Revised", a la cultura brasileña. MÉTODOS: Para el procedimiento metodológico se siguieron las etapas recomendadas internacionalmente: traducción; retrotraducción; evaluación por un grupo de jueces y pre-test. RESULTADOS: Las etapas de traducción y retrotraducción fueron realizadas satisfactoriamente, la evaluación de la versión síntesis por el comité de jueces resultó en alteración en la mayoría de los ítems, garantizando las equivalencias entre las versiones original y traducida. Durante el pre-test, se verificó la necesidad de reformulaciones de algunos ítems, tornándolos más claros y de fácil comprensión. CONCLUSION: Se destaca que, a pesar de la complejidad del instrumento, el proceso de traducción y adaptación cultural del Nursing Work Index - Revised, a la cultura brasileña fue concluido con êxito.OBJECTIVE: To translate and establish the cross-cultural validation of the "Nursing Work Index - Revised" into Brazilian Portuguese. METHODS: Internationally recommended methodological procedures were followed

Blended Approach to Occupational Performance (BAOP: Guidelines Enabling Children with Autism

Directory of Open Access Journals (Sweden)

Jordan M. Skowronski

2017-01-01

Full Text Available The performance of daily activities is impacted by motor impairments in children with autism spectrum disorders (ASD. Research has recently demonstrated the prevalence and specificity of motor impairments in people with ASD. The motor learning of individuals with ASD is partially intact, and evidence suggests that a method to alter skill learning and repeated practice of motor sequences might be beneficial. Aiming to use this knowledge to guide occupational therapy interventions, initial guidelines for children with ASD blended Cognitive Orientation to daily Occupational Performance (CO-OP with virtual reality (VR were created. An expert panel reviewed the initial guidelines. The results from the semi-structured expert panel discussion were to (a increase the number of sessions, (b provide more visuals to children, and (c use VR as a reinforcer. Guidelines were revised accordingly. The revised guidelines, called Blended Approach to Occupational Performance (BAOP, are ready for further testing.

Addenbrooke's Cognitive Examination-Revised for mild cognitive impairment in Parkinson's disease.

Science.gov (United States)

McColgan, Peter; Evans, Jonathan R; Breen, David P; Mason, Sarah L; Barker, Roger A; Williams-Gray, Caroline H

2012-08-01

Cognitive impairment is common in Parkinson's disease (PD), even in the early stages, and appropriate screening tools are needed. We investigated the utility of the Addenbrooke's Cognitive Examination-Revised for detecting mild cognitive impairment (MCI) in PD in an incident population-representative cohort (n = 132) and investigated the relationship between performance on this instrument and behavior and quality of life (n = 219). Twenty-two percent met criteria for MCI. Receiver operating curve analysis revealed an area under the curve of 0.81. A cutoff Cognitive Rating Scale, and there were significant correlations with the Cambridge Behavioral Inventory-Revised and Parkinson's Disease Questionnaire 39. This instrument is a useful screening tool for PD-MCI, and poor performance is significantly related to impaired behavior and quality of life. Copyright © 2012 Movement Disorder Society.

Modified performance test of vented lead acid batteries for stationary applications

International Nuclear Information System (INIS)

Uhlir, K.W.; Fletcher, R.J.

1995-01-01

The concept of a modified performance test for vented lead acid batteries in stationary applications has been developed by the IEEE Battery Working Group. The modified performance test is defined as a test in the ''as found'' condition of the battery capacity and its ability to provide a high rate, short duration load (usually the highest rate of the duty cycle) that will confirm the battery's ability to meet the critical period of the load duty cycle, in addition to determining its percentage of rated capacity. This paper will begin by reviewing performance and service test requirements and concerns associated with both types of tests. The paper will then discuss the rationale for developing a modified performance test along with the benefits that can be derived from performing a modified performance test in lieu of a capacity test and/or a service test. The paper will conclude with an example on how to apply a modified performance test and test acceptance criteria

Revised National Pressure Ulcer Advisory Panel Pressure Injury Staging System: Revised Pressure Injury Staging System.

Science.gov (United States)

Edsberg, Laura E; Black, Joyce M; Goldberg, Margaret; McNichol, Laurie; Moore, Lynn; Sieggreen, Mary

Our understanding of pressure injury etiology and development has grown in recent years through research, clinical expertise, and global interdisciplinary expert collaboration. Therefore, the National Pressure Ulcer Advisory Panel (NPUAP) has revised the definition and stages of pressure injury. The revision was undertaken to incorporate the current understanding of the etiology of pressure injuries, as well as to clarify the anatomical features present or absent in each stage of injury. An NPUAP-appointed Task Force reviewed the literature and created drafts of definitions, which were then reviewed by stakeholders and the public, including clinicians, educators, and researchers around the world. Using a consensus-building methodology, these revised definitions were the focus of a multidisciplinary consensus conference held in April 2016. As a result of stakeholder and public input, along with the consensus conference, important changes were made and incorporated into the new staging definitions. The revised staging system uses the term injury instead of ulcer and denotes stages using Arabic numerals rather than Roman numerals. The revised definition of a pressure injury now describes the injuries as usually occurring over a bony prominence or under a medical or other device. The revised definition of a Stage 2 pressure injury seeks to clarify the difference between moisture-associated skin damage and injury caused by pressure and/or shear. The term suspected has been removed from the Deep Tissue Pressure Injury diagnostic label. Each definition now describes the extent of tissue loss present and the anatomical features that may or may not be present in the stage of injury. These important revisions reflect the methodical and collaborative approach used to examine the available evidence and incorporate current interdisciplinary clinical expertise into better defining the important phenomenon of pressure injury etiology and development.

Microcomputers and the Improvement of Revision Skills.

Science.gov (United States)

Balajthy, Ernest; And Others

1987-01-01

Discusses use of word processing software as an effective tool in writing and revision instruction, and describes the role of the teacher. Examples of exercises that encourage revision and of software designed to teach effective revision skills are reviewed. (MBR)

Individual questions of financial control and revision

Directory of Open Access Journals (Sweden)

В. М. Глібко

2015-05-01

Full Text Available Problem setting. In modern conditions at investigation and gathering of proofs in criminal proceedings according to item 93 CPC of Ukraine collecting of proofs which is carried out by the criminal proceedings parties, victim is important, the representative of the legal person, in which relation carries out manufacture, including a way истребования and receptions from public authorities, local governments, the enterprises, establishments and organisations, official and physical persons of things, documents, data, conclusions of experts, conclusions of revisions and certificates of checks. Recent research and publications analisis. In scientific sources questions of carrying out of revisions S. B.Zhivko, V.V.Akimov, G.Demjanchuk, J.Buzdugan is considered. Paper objective. Article purpose is studying and definition of a place of revision among forms of inspection of the state control and use of results of revision in criminal proceedings. Paper main body. Off-schedule exit revision that is revision which is not provided in plans of work of body of the state financial control is considered and is spent at presence at least one of the circumstances listed in item 11 of the Law of Ukraine «About main principles of realisation of the state financial control in Ukraine». If revision is carried out on request of investigating bodies it is spent on the basis of the petition of the inspector and accepted by the results of consideration of this petition of the decision of the investigatory judge. The primary goal of revision on request of investigating bodies or on the basis of court definition is reception of proofs on business. Therefore the revision certificate admits the written proof as on the basis of its conclusion of the inspector, the public prosecutor receives the information on a perfect crime, abusing, and also on the persons who have committed a crime, on the period of commission of crime and an amount of damage. In criminal

Outcome, revision rate and indication for revision following resurfacing hemiarthroplasty for osteoarthritis of the shoulder

DEFF Research Database (Denmark)

Rasmussen, J V; Polk, A; Sorensen, A K

2014-01-01

In this study, we evaluated patient-reported outcomes, the rate of revision and the indications for revision following resurfacing hemiarthroplasty of the shoulder in patients with osteoarthritis. All patients with osteoarthritis who underwent primary resurfacing hemiarthroplasty and reported...... to the Danish Shoulder Arthroplasty Registry (DSR), between January 2006 and December 2010 were included. There were 772 patients (837 arthroplasties) in the study. The Western Ontario Osteoarthritis of the Shoulder (WOOS) index was used to evaluate patient-reported outcome 12 months (10 to 14) post......-operatively. The rates of revision were calculated from the revisions reported to the DSR up to December 2011 and by checking deaths with the Danish National Register of Persons. A complete questionnaire was returned by 688 patients (82.2%). The mean WOOS was 67 (0 to 100). A total of 63 hemiarthroplasties (7...

[Incorporation of an organic MAGIC (Model of Acidification of Groundwater in Catchments) and testing of the revised model using independent data sources]. Progress report, March 16, 1992--September 15, 1992

Energy Technology Data Exchange (ETDEWEB)

Sullivan, T.J.

1992-09-01

A project was initiated in March, 1992 to (1) incorporate a rigorous organic acid representation, based on empirical data and geochemical considerations, into the MAGIC model of acidification response, and (2) test the revised model using three sets of independent data. After six months of performance, the project is on schedule and the majority of the tasks outlined for Year 1 have been successfully completed. Major accomplishments to data include development of the organic acid modeling approach, using data from the Adirondack Lakes Survey Corporation (ALSC), and coupling the organic acid model with MAGIC for chemical hindcast comparisons. The incorporation of an organic acid representation into MAGIC can account for much of the discrepancy earlier observed between MAGIC hindcasts and paleolimnological reconstructions of preindustrial pH and alkalinity for 33 statistically-selected Adirondack lakes. Additional work is on-going for model calibration and testing with data from two whole-catchment artificial acidification projects. Results obtained thus far are being prepared as manuscripts for submission to the peer-reviewed scientific literature.

Performance test of solar-assisted ejector cooling system

KAUST Repository

Huang, Bin-Juine

2014-03-01

A solar-assisted ejector cooling/heating system (SACH-2k) is built and test result is reported. The solar-driven ejector cooling system (ECS) is connected in series with an inverter-type air conditioner (IAC). Several advanced technologies are developed in SACH-k2, including generator liquid level control in ECS, the ECS evaporator temperature control, and optimal control of fan power in cooling tower of ECS. From the field test results, the generator liquid level control performs quite well and keeps stable performance of ejector. The ECS evaporator temperature control also performs satisfactorily to keep ejector performance normally under low or fluctuating solar radiation. The fan power control system cooling tower performs stably and reduces the power consumption dramatically without affecting the ECS performance. The test results show that the overall system COPo including power consumptions of peripheral increases from 2.94-3.3 (IAC alone) to 4.06-4.5 (SACH-k2), about 33-43%. The highest COPo is 4.5. © 2013 Elsevier Ltd and IIR. All rights reserved.

The Performance test of Mechanical Sodium Pump with Water Environment

International Nuclear Information System (INIS)

Cho, Chungho; Kim, Jong-Man; Ko, Yung Joo; Jeong, Ji-Young; Kim, Jong-Bum; Ko, Bock Seong; Park, Sang Jun; Lee, Yoon Sang

2015-01-01

As contrasted with PWR(Pressurized light Water Reactor) using water as a coolant, sodium is used as a coolant in SFR because of its low melting temperature, high thermal conductivity, the high boiling temperature allowing the reactors to operate at ambient pressure, and low neutron absorption cross section which is required to achieve a high neutron flux. But, sodium is violently reactive with water or oxygen like the other alkali metal. So Very strict requirements are demanded to design and fabricate of sodium experimental facilities. Furthermore, performance testing in high temperature sodium environments is more expensive and time consuming and need an extra precautions because operating and maintaining of sodium experimental facilities are very difficult. The present paper describes performance test results of mechanical sodium pump with water which has been performed with some design changes using water test facility in SAM JIN Industrial Co. To compare the hydraulic characteristic of model pump with water and sodium, the performance test of model pump were performed using vender's experimental facility for mechanical sodium pump. To accommodate non-uniform thermal expansion and to secure the operability and the safety, the gap size of some parts of original model pump was modified. Performance tests of modified mechanical sodium pump with water were successfully performed. Water is therefore often selected as a surrogate test fluid because it is not only cheap, easily available and easy to handle but also its important hydraulic properties (density and kinematic viscosity) are very similar to that of the sodium. Normal practice to thoroughly test a design or component before applied or installed in reactor is important to ensure the safety and operability in the sodium-cooled fast reactor (SFR). So, in order to estimate the hydraulic behavior of the PHTS pump of DSFR (600 MWe Demonstraion SFR), the performance tests of the model pump such as performance

Carbohydrate ingestion improves performance of a new reliable test of soccer performance.

Science.gov (United States)

Currell, Kevin; Conway, Steve; Jeukendrup, Asker E

2009-02-01

The aim of the study was to investigate the reliability of a new test of soccer performance and evaluate the effect of carbohydrate (CHO) on soccer performance. Eleven university footballers were recruited and underwent 3 trials in a randomized order. Two of the trials involved ingesting a placebo beverage, and the other, a 7.5% maltodextrin solution. The protocol comprised a series of ten 6-min exercise blocks on an outdoor Astroturf pitch, separated by the performance of 2 of the 4 soccer-specific tests, making the protocol 90 min in duration. The intensity of the exercise was designed to be similar to the typical activity pattern during soccer match play. Participants performed skill tests of dribbling, agility, heading, and shooting throughout the protocol. The coefficients of variation for dribbling, agility, heading, and shooting were 2.2%, 1.2%, 7.0%, and 2.8%, respectively. The mean combined placebo scores were 42.4 +/- 2.7 s, 43.1 +/- 3.7 s, 210 +/- 34 cm, and 212 +/- 17 points for agility, dribbling, heading, and kicking, respectively. CHO ingestion led to a combined agility time of 41.5 +/- 0.8 s, for dribbling 41.7 +/- 3.5 s, 213 +/- 11 cm for heading, and 220 +/- 5 points for kicking accuracy. There was a significant improvement in performance for dribbling, agility, and shooting (p soccer performance, and ingesting CHO leads to an improvement in soccer performance.

High voltage test techniques

CERN Document Server

Kind, Dieter

2001-01-01

The second edition of High Voltage Test Techniques has been completely revised. The present revision takes into account the latest international developments in High Voltage and Measurement technology, making it an essential reference for engineers in the testing field.High Voltage Technology belongs to the traditional area of Electrical Engineering. However, this is not to say that the area has stood still. New insulating materials, computing methods and voltage levels repeatedly pose new problems or open up methods of solution; electromagnetic compatibility (EMC) or components and systems al

Gallium-cladding compatibility testing plan: Phase 3: Test plan for centrally heated surrogate rodlet test. Revision 2

International Nuclear Information System (INIS)

Morris, R.N.; Baldwin, C.A.; Wilson, D.F.

1998-07-01

The Fissile Materials Disposition Program (FMDP) is investigating the use of weapons grade plutonium in mixed oxide (MOX) fuel for light-water reactors (LWR). Commercial MOX fuel has been successfully used in overseas reactors for many years; however, weapons derived fuel may differ from the previous commercial fuels because of small amounts of gallium impurities. A concern presently exists that the gallium may migrate out of the fuel, react with and weaken the clad, and thereby promote loss of fuel pin integrity. Phases 1 and 2 of the gallium task are presently underway to investigate the types of reactions that occur between gallium and clad materials. This is a Level-2 document as defined in the Fissile Materials Disposition Program Light-Water Reactor Mixed-Oxide Fuel Irradiation Test Project Plan. This Plan summarizes the projected Phase 3 Gallium-Cladding compatibility heating test and the follow-on post test examination (PTE). This work will be performed using centrally-heated surrogate pellets, to avoid unnecessary complexities and costs associated with working with plutonium and an irradiation environment. Two sets of rodlets containing pellets prepared by two different methods will be heated. Both sets will have an initial bulk gallium content of approximately 10 ppm. The major emphasis of the PTE task will be to examine the material interactions, particularly indications of gallium transport from the pellets to the clad

Psychometric Properties of the Revised Teachers' Attitude toward Inclusion Scale

Science.gov (United States)

Monsen, Jeremy J.; Ewing, Donna L.; Boyle, James

2015-01-01

This paper presents the psychometric properties of a questionnaire measure that updates and extends Larrivee and Cook's (1979) Opinions Relative to Mainstreaming Scale in terms of structure, terminology, and language. The revised scale was tested using a sample of 106 teachers based in inclusive mainstream schools. Using Principal Component…

DEVELOPING an ENGLISH PERFORMANCE TEST for INCOMING INDONESIAN COLLEGE STUDENTS

Directory of Open Access Journals (Sweden)

Bill Glenny Wullur

2011-07-01

Full Text Available Abstracts This study constructed, developed and validated an English Performance test as a complementary to an existing placement test in Universitas Klabat, Manado, Indonesia.  It is designed to provide a valid criterion-based measurement within the placement programs of the said university. The study aimed to answer the following questions: (1 What test tasks and items are needed in a performance test based on current language testing theory? (2 Is the performance test valid? (3 Is the scoring of the performance test reliable? (4 Is the performance test practical and predictive? And (5 What are the ratings of the resultant performance test? The steps in developing a performance test involved conducting needs analysis, establishing attributes of good performance test, and constructing test specification based on current language testing theory.  The speech event chosen which would generate language use was applying for financial assistance.  From this speech event, four activities were elicited: (1 writing a letter of inquiry, (2 completing an application form, (3 making an appointment for interview, (4 giving an oral presentation/interview.  These activities represent the four authentic tasks in which the desirable modes/channel of communication, language functions and skills, genre, and topic are integrated. The developed test is divided into four sections corresponding with the elicited tasks: (1 Formal letter, (2 Application form, (3 Making Appointment, and (4 Oral Presentation. The test was validated in several ways: (1 face validation compared the scores of Indonesian studying in the Philippines and in Indonesia, and found that the scores are highly correlated at Spearman ρ = .85.  (2 The content validation relied on the evaluation of expert informants.  The finding shows that the content coverage and relevance of the test is highly satisfactory. (3 The concurrent validation was conducted to the existing placement test and found

Performance tests for integral reactor nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Sohn, Dong-Seong; Yim, Jeong-Sik; Lee, Chong-Tak; Kim, Han-Soo; Koo, Yang-Hyun; Lee, Byung-Ho; Cheon, Jin-Sik; Oh, Je-Yong

2006-02-15

An integral type reactor SMART plans to utilize metallic Zr-U fuel which is Zr-based alloy with 34{approx}38 wt% U. In order to verify the technologies for the design and manufacturing of the fuel and get a license, performance tests were carried out. Experimental Fuel Assembly (EFA) manufactured in KAERI is being successfully irradiated in the MIR reactor of RIAR from September 4 2004, and it has achieved burnup of 0.21 g/cc as of January 25 2006. Thermal properties of irradiated Zr-U fuel were measured. Up to the phase transformation temperature, thermal diffusivity increased linearly in proportion to temperature. However its dependence on the burnup was not significant. RIA tests with 4 unirradiated Zr-U fuel rods were performed in Kurchatov Institute to establish a safety criterion. In the case of the un-irradiated Zr-U fuel, the energy deposition during the control rod ejection accident should be less than 172 cal/g to prevent the failure accompanying fuel fragmentation and dispersal. Finally the irradiation tests of fuel rods have been performed at HANARO. The HITE-2 test was successfully completed up to a burnup of 0.31 g/cc. The HITE-3 test began in February 2004 and will be continued up to a target burnup of 0.6 g/cc.

Modulatory effects of psychopathy on Wisconsin Card Sorting Test performance in male offenders with Antisocial Personality Disorder.

Science.gov (United States)

Pera-Guardiola, Vanessa; Batalla, Iolanda; Bosque, Javier; Kosson, David; Pifarré, Josep; Hernández-Ribas, Rosa; Goldberg, Ximena; Contreras-Rodríguez, Oren; Menchón, José M; Soriano-Mas, Carles; Cardoner, Narcís

2016-01-30

Neuropsychological deficits in executive functions (EF) have been linked to antisocial behavior and considered to be cardinal to the onset and persistence of severe antisocial and aggressive behavior. However, when psychopathy is present, prior evidence suggests that the dorsolateral prefrontal cortex is unaffected leading to intact EF. Ninety-one male offenders with Antisocial Personality Disorder (ASPD) and 24 controls completed the Wisconsin Card Sorting Test (WCST). ASPD individuals were grouped in three categories according to Psychopathy Checklist-Revised (PCL-R) scores (low, medium and high). We hypothesized that ASPD offenders with high PCL-R scores will not differ from healthy controls in EF and will show better EF performance in comparison with subjects with low PCL-R scores. Results showed that ASPD offenders with low PCL-R scores committed more perseverative errors and responses than controls and offenders with high PCL-R scores, which did not differ from healthy controls. Moreover, scores on Factor 1 and the interpersonal facet of the PCL-R were predictors of better WCST performance. Our results suggest a modulatory role of psychopathy in the cognitive performance of ASPD offenders, and provide further evidence supporting that offenders with ASPD and psychopathy are characterized by a cognitive profile different from those with ASPD without psychopathy. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Test Driven Development: Performing Art

Science.gov (United States)

Bache, Emily

The art of Test Driven Development (TDD) is a skill that needs to be learnt, and which needs time and practice to master. In this workshop a select number of conference participants with considerable skill and experience are invited to perform code katas [1]. The aim is for them to demonstrate excellence and the use of Test Driven Development, and result in some high quality code. This would be for the benefit of the many programmers attending the conference, who could come along and witness high quality code being written using TDD, and get a chance to ask questions and provide feedback.

Recent trends on Software Verification and Validation Testing

International Nuclear Information System (INIS)

Kim, Hyungtae; Jeong, Choongheui

2013-01-01

Verification and Validation (V and V) include the analysis, evaluation, review, inspection, assessment, and testing of products. Especially testing is an important method to verify and validate software. Software V and V testing covers test planning to execution. IEEE Std. 1012 is a standard on the software V and V. Recently, IEEE Std. 1012-2012 was published. This standard is a major revision to IEEE Std. 1012-2004 which defines only software V and V. It expands the scope of the V and V processes to include system and hardware as well as software. This standard describes the scope of V and V testing according to integrity level. In addition, independent V and V requirement related to software V and V testing in IEEE 7-4.3.2-2010 have been revised. This paper provides a recent trend of software V and V testing by reviewing of IEEE Std. 1012-2012 and IEEE 7-4.3.2-2010. There are no major changes of software V and V testing activities and tasks in IEEE 1012-2012 compared with IEEE 1012-2004. But the positions on the responsibility to perform software V and V testing are changed. In addition IEEE 7-4.3.2-2010 newly describes the positions on responsibility to perform Software V and V Testing. However, the positions of these standards on the V and V testing are different. For integrity level 3 and 4, IEEE 1012-2012 basically requires that V and V organization shall conduct all of V and V testing tasks such as test plan, test design, test case, and test procedure except test execution. If V and V testing is conducted by not V and V but another organization, the results of that testing shall be analyzed by the V and V organization. For safety-related software, IEEE 7-4.3.2-2010 requires that test procedures and reports shall be independently verified by the alternate organization regardless of who writes the procedures and/or conducts the tests

Structural, Item, and Test Generalizability of the Psychopathy Checklist-Revised to Offenders with Intellectual Disabilities

Science.gov (United States)

Morrissey, Catrin; Cooke, David; Michie, Christine; Hollin, Clive; Hogue, Todd; Lindsay, William R.; Taylor, John L.

2010-01-01

The Psychopathy Checklist-Revised (PCL-R) is the most widely used measure of psychopathy in forensic clinical practice, but the generalizability of the measure to offenders with intellectual disabilities (ID) has not been clearly established. This study examined the structural equivalence and scalar equivalence of the PCL-R in a sample of 185 male…

Development of a grinding-specific performance test set-up.

Science.gov (United States)

Olesen, C G; Larsen, B H; Andresen, E L; de Zee, M

2015-01-01

The aim of this study was to develop a performance test set-up for America's Cup grinders. The test set-up had to mimic the on-boat grinding activity and be capable of collecting data for analysis and evaluation of grinding performance. This study included a literature-based analysis of grinding demands and a test protocol developed to accommodate the necessary physiological loads. This study resulted in a test protocol consisting of 10 intervals of 20 revolutions each interspersed with active resting periods of 50 s. The 20 revolutions are a combination of both forward and backward grinding and an exponentially rising resistance. A custom-made grinding ergometer was developed with computer-controlled resistance and capable of collecting data during the test. The data collected can be used to find measures of grinding performance such as peak power, time to complete and the decline in repeated grinding performance.

A short version of the revised 'experience of close relationships questionnaire': investigating non-clinical and clinical samples.

Science.gov (United States)

Wongpakaran, Tinakon; Wongpakaran, Nahathai

2012-01-01

This study seeks to investigate the psychometric properties of the short version of the revised 'Experience of Close Relationships' questionnaire, comparing non-clinical and clinical samples. In total 702 subjects participated in this study, of whom 531 were non-clinical participants and 171 were psychiatric patients. They completed the short version of the revised 'Experience of Close Relationships' questionnaire (ECR-R-18), the Perceived Stress Scale-10(PSS-10), the Rosenberg Self-Esteem Scale (RSES) and the UCLA Loneliness scale. A retest of the ECR-R-18 was then performed at four-week intervals. Then, confirmatory factor analyses were performed to test the validity of the new scale. The ECR-R-18 showed a fair to good internal consistency (α 0.77 to 0.87) for both samples, and the test-retest reliability was found to be satisfactory (ICC = 0.75). The anxiety sub-scale demonstrated concurrent validity with PSS-10 and RSES, while the avoidance sub-scale showed concurrent validity with the UCLA Loneliness Scale. Confirmatory factor analysis using method factors yielded two factors with an acceptable model fit for both groups. An invariance test revealed that the ECR-R-18 when used on the clinical group differed from when used with the non-clinical group. The ECR-R-18 questionnaire revealed an overall better level of fit than the original 36 item questionnaire, indicating its suitability for use with a broader group of samples, including clinical samples. The reliability of the ECR-R- 18 might be increased if a modified scoring system is used and if our suggestions with regard to future studies are followed up.

Reliability performance testing of totally encapsulating chemical protective suits

International Nuclear Information System (INIS)

Johnson, J.S.; Swearengen, P.M.

1991-01-01

The need to assure a high degree of reliability for totally encapsulating chemical protective (TECP) suits has been recognized by Lawrence Livermore National Laboratory's (LLNL) Hazards Control Department for some time. The following four tests were proposed as necessary to provide complete evaluation of TECP suit performance: 1. Quantitative leak test (ASTM draft), 2. Worst-case chemical exposure test (conceptual), 3. Pressure leak-rate test (complete, ASTM F1057-87), and 4. Chemical leak-rate test (ASTM draft). This paper reports on these tests which should be applied to measuring TECP suit performance in two stages: design qualification tests and field use tests. Test 1, 2, and 3 are used as design qualification tests, and tests 3 and 4 are used as field use tests

Using a Bedside Video-assisted Test Tube Test to Assess Stoma Viability: A Report of 4 Cases.

Science.gov (United States)

Ahmad, Sarwat; Turner, Keli; Shah, Paulesh; Diaz, Jose

2016-07-01

Mucosal discoloration of an intestinal stoma may indicate self-limited venous congestion or necrosis necessitating operative revision. A common bedside technique to assess stoma viability is the "test tube test". A clear tube is inserted into the stoma and a hand-held light is used to assess the color of the stoma. A technique (video-assisted test tube test [VATTT]) developed by the authors utilizes a standard video bronchoscope inserted into a clear plastic blood collection tube to visually inspect and assess the mucosa. This technique was evaluated in 4 patients (age range 49-72 years, all critically ill) with a discolored stoma after emergency surgery. In each case, physical exam revealed ischemic mucosa at the surface either immediately after surgery or after worsening hypotension weeks later. Serial test tube test assessments were ambiguous when trying to assess deeper mucosa. The VATTT assessment showed viable pink mucosa beneath the surface and until the fascia was revealed in 3 patients. One (1) patient had mucosal ischemia down to the fascia, which prompted operative revision of the stoma. The new stoma was assessed with a VATTT and was viable for the entire length of the stoma. VATTT provided an enhanced, magnified, and clearer way to visually assess stoma viability in the postoperative period that can be performed at the bedside with no adverse events. It may prevent unnecessary relaparotomy or enable earlier diagnosis of deep ostomy necrosis. Validity and reliability studies are warranted.

Performance demonstration tests for eddy current inspection of steam generator tubing

International Nuclear Information System (INIS)

Kurtz, R.J.; Heasler, P.G.; Anderson, C.M.

1996-05-01

This report describes the methodology and results for development of performance demonstration tests for eddy current (ET) inspection of steam generator tubes. Statistical test design principles were used to develop the performance demonstration tests. Thresholds on ET system inspection performance were selected to ensure that field inspection systems would have a high probability of detecting and and correctly sizing tube degradation. The technical basis for the ET system performance thresholds is presented in detail. Statistical test design calculations for probability of detection and flaw sizing tests are described. A recommended performance demonstration test based on the design calculations is presented. A computer program for grading the probability of detection portion of the performance demonstration test is given

Performance demonstration tests for eddy current inspection of steam generator tubing

Energy Technology Data Exchange (ETDEWEB)

Kurtz, R.J.; Heasler, P.G.; Anderson, C.M.

1996-05-01

This report describes the methodology and results for development of performance demonstration tests for eddy current (ET) inspection of steam generator tubes. Statistical test design principles were used to develop the performance demonstration tests. Thresholds on ET system inspection performance were selected to ensure that field inspection systems would have a high probability of detecting and and correctly sizing tube degradation. The technical basis for the ET system performance thresholds is presented in detail. Statistical test design calculations for probability of detection and flaw sizing tests are described. A recommended performance demonstration test based on the design calculations is presented. A computer program for grading the probability of detection portion of the performance demonstration test is given.

Test anxiety and academic performance in chiropractic students.

Science.gov (United States)

Zhang, Niu; Henderson, Charles N R

2014-01-01

Objective : We assessed the level of students' test anxiety, and the relationship between test anxiety and academic performance. Methods : We recruited 166 third-quarter students. The Test Anxiety Inventory (TAI) was administered to all participants. Total scores from written examinations and objective structured clinical examinations (OSCEs) were used as response variables. Results : Multiple regression analysis shows that there was a modest, but statistically significant negative correlation between TAI scores and written exam scores, but not OSCE scores. Worry and emotionality were the best predictive models for written exam scores. Mean total anxiety and emotionality scores for females were significantly higher than those for males, but not worry scores. Conclusion : Moderate-to-high test anxiety was observed in 85% of the chiropractic students examined. However, total test anxiety, as measured by the TAI score, was a very weak predictive model for written exam performance. Multiple regression analysis demonstrated that replacing total anxiety (TAI) with worry and emotionality (TAI subscales) produces a much more effective predictive model of written exam performance. Sex, age, highest current academic degree, and ethnicity contributed little additional predictive power in either regression model. Moreover, TAI scores were not found to be statistically significant predictors of physical exam skill performance, as measured by OSCEs.

How to Revise, and Revise Really Well, for Premier Academic Journals

DEFF Research Database (Denmark)

LaPlaca, Peter J.; Lindgreen, Adam; Vanhamme, Joelle

2018-01-01

Most of the premier academic journals in all fields routinely have rejection rates of 80%, 95%, or higher. All journals prefer articles that make significant contributions to the field. Revising a manuscript and responding properly to the comments of reviewers and editors often is challenging....... This article discusses how to revise effectively a manuscript according to the (minor or major) comments of reviewers and editors for premier academic journals. We provide a series of tips for helping the authors in their endeavor, making the process less arduous and improving the possibility of a positive...

Drop Performance Test of CRDMs for JRTR

Energy Technology Data Exchange (ETDEWEB)

Choi, Myoung-Hwan; Cho, Yeong-Garp; Chung, Jong-Ha [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Jung-Hyun [POSCO Plandtec Co. Ltd, Ulsan (Korea, Republic of); Lee, Kwan-Hee [RIST, Pohang (Korea, Republic of)

2015-10-15

The drop test results of CRDMs with AC-type electromagnet show that the initial delay times are not satisfied with the requirement, 0.15 seconds. After the replacement of the electromagnet from AC-type to DCtype, the drop times of CARs and accelerations due to the impact of moving parts are satisfied with all requirements. As a result, it is found that four CRDMs to be installed at site have a good drop performance, and meet all performance requirements. A control rod drive mechanism (CRDM) is a device to control the position of a control absorber rod (CAR) in the core by using a stepping motor which is commanded by the reactor regulating system (RRS) to control the reactivity during the normal operation of the reactor. The top-mounted CRDM driven by the stepping motor for Jordan Research and Training Reactor (JRTR) has been developed in KAERI. The CRDM for JRTR has been optimized by the design improvement based on that of the HANARO. It is necessary to verify the performances such as the stepping, drop, endurance, vibration, seismic and structural integrity for active components. Especially, the CAR drop curves are important data for the safety analysis. This paper describes the test results to demonstrate the drop performances of a prototype and 4 CRDMs to be installed at site. The tests are carried out at a test rig simulating the actual reactor's conditions.

A taxonomic revision of the genus Podocarpus

NARCIS (Netherlands)

Laubenfels, de D.J.

1985-01-01

In connection with the forthcoming revision of the Coniferae for the Flora Malesiana, the author thought it necessary to revise the genus Podocarpus. Although this genus has a substantial representation in Malesia (30 species), the revision is too involved to be appropriate with the Flora Malesiana

An Examination and Revision of the Love Attitude Scale in Serbia

Directory of Open Access Journals (Sweden)

Bojan Todosijević

2009-06-01

Full Text Available The research reports on results of an initial application of the Love Attitude Scale (Hendrick & Hendrick, 1986 in Serbia. The study was conducted on the sample of 127 respondents, mainly of adolescent age, from Subotica, Serbia. We explored the factor structure of the Love Attitude Scale, analyzed relationships between its subscales, and examined relevant correlates of its dimensions. We also performed extensive item analysis of the scale, and proposed several new items for the use in the revised Love Attitude Scale for Serbia. Correlates of the revised subscales correspond to those obtained with the original scale and in other countries. The results confirm cross-cultural stability of the six-dimensional structure of the Love Attitude Scale. It was concluded that the Serbian adaptation was successful, and that the translated and slightly revised scale can be used as a valid instrument for the assessment of the six love styles.

(Re)visions to a Secondary Teacher Education Course: Trials and Triumphs in Attempting to Disrupt Hegemonic Understandings and Performances of Education

Science.gov (United States)

Bullock, Patricia L.; Freedman, Debra M.

2006-01-01

The purpose of this paper is to explore curricular (re)visions made over the span of two semesters to a required secondary teacher education course. Specifically, we focus on our trials and triumphs in implementing the revised curricula. Our work is guided by the following question: in what ways do preservice teachers deem the diversity-focused…

New test methods for BIPV. Results from IP performance

International Nuclear Information System (INIS)

Jol, J.C.; Van Kampen, B.J.M.; De Boer, B.J.; Reil, F.; Geyer, D.

2009-11-01

Within the Performance project new test procedures for PV building products and the building performance as a whole when PV is applied in buildings have been drafted. It has resulted in a first draft of new test procedures for PV building products and proposals for tests for novel BIPV technology like thin film. The test proposed are a module breakage test for BIPV products, a fire safety test for BIPV products and a dynamic load test for BIPV products. Furthermore first proposals of how flexible PV modules could be tested in an appropriate way to ensure long time quality and safety of these new products are presented.

Corrosion performance tests for reinforcing steel in concrete : test procedures.

Science.gov (United States)

2009-09-01

The existing test method to assess the corrosion performance of reinforcing steel embedded in concrete, mainly : ASTM G109, is labor intensive, time consuming, slow to provide comparative results, and often expensive. : However, corrosion of reinforc...

W-087 Operational test report. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Joshi, A.W.

1997-06-10

This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks. The equipment to be tested includes the following: a. Leak detection system operation and controls. b. Electrical interlocks.- C. Transfer pump oper ation. d. Vacuum breaker system interlocks.

Complications Following Primary and Revision Transsphenoidal Surgeries for Pituitary Tumors

Science.gov (United States)

Krings, James G.; Kallogjeri, Dorina; Wineland, Andre; Nepple, Kenneth G.; Piccirillo, Jay F.; Getz, Anne E.

2014-01-01

Objective This study aimed to determine the incidence of major complications following both primary and revision transsphenoidal pituitary surgery. Major complications included endocrinopathic, skull base, orbital, hemorrhagic and thromboembolic complications, respiratory failure, and death. Secondarily, this study aimed to examine factors associated with the occurrence of complications. Study Design Retrospective cohort analysis of California and Florida all-payer databases from 2005-2008. Methods The major complication rate following both primary and revision transsphenoidal pituitary surgery was calculated. Bivariate analyses were performed to investigate the relationship of patient characteristics with complication occurrence, and a multivariate model was constructed to determine risk factors associated with these complications. Results 5,277 primary cases and 192 revision cases met inclusion criteria. There was a non-significant absolute difference of 3.09% (95% CI −11.00 to 16.14) between the rate of complications following primary (n=443; 8.39%) and revision (n=22; 11.46%) surgeries. Multivariate analyses showed that patients with Medicare (OR=1.74; 95% CI 1.17 to 2.61), Medicaid (OR=2.13; 95% CI 1.59 to 2.86), or a malignant neoplasm (OR=3.10; 95% CI 1.62 to 5.93) were more likely to have complications. Conclusions The rate of major complications following transsphenoidal pituitary surgery is lower than earlier retrospective reports. The overall complication rate following revision surgery was not significantly different from primary surgery. Insurance status and a diagnosis of a malignant neoplasm were associated with a higher rate of complications. PMID:25263939

Impact of Educational Level on Performance on Auditory Processing Tests.

Science.gov (United States)

Murphy, Cristina F B; Rabelo, Camila M; Silagi, Marcela L; Mansur, Letícia L; Schochat, Eliane

2016-01-01

Research has demonstrated that a higher level of education is associated with better performance on cognitive tests among middle-aged and elderly people. However, the effects of education on auditory processing skills have not yet been evaluated. Previous demonstrations of sensory-cognitive interactions in the aging process indicate the potential importance of this topic. Therefore, the primary purpose of this study was to investigate the performance of middle-aged and elderly people with different levels of formal education on auditory processing tests. A total of 177 adults with no evidence of cognitive, psychological or neurological conditions took part in the research. The participants completed a series of auditory assessments, including dichotic digit, frequency pattern and speech-in-noise tests. A working memory test was also performed to investigate the extent to which auditory processing and cognitive performance were associated. The results demonstrated positive but weak correlations between years of schooling and performance on all of the tests applied. The factor "years of schooling" was also one of the best predictors of frequency pattern and speech-in-noise test performance. Additionally, performance on the working memory, frequency pattern and dichotic digit tests was also correlated, suggesting that the influence of educational level on auditory processing performance might be associated with the cognitive demand of the auditory processing tests rather than auditory sensory aspects itself. Longitudinal research is required to investigate the causal relationship between educational level and auditory processing skills.

MFTF test coil construction and performance

International Nuclear Information System (INIS)

Cornish, D.N.; Zbasnik, J.P.; Leber, R.L.; Hirzel, D.G.; Johnston, J.E.; Rosdahl, A.R.

1978-01-01

A solenoid coil, 105 cm inside the 167 cm outside diameter, has been constructed and tested to study the performance of the stabilized Nb--Ti conductor to be used in the Mirror Fusion Test Facility (MFTF) being built at Lawrence Livermore Laboratory. The insulation system of the test coil is identical to that envisioned for MFTF. Cold-weld joints were made in the conductor at the start and finish of each layer; heaters were fitted to some of these joints and also to the conductor at various locations in the winding. This paper gives details of the construction of the coil and the results of the tests carried out to determine its propagation and recovery characteristics

Effect of graft choice on the outcome of revision anterior cruciate ligament reconstruction in the Multicenter ACL Revision Study (MARS) Cohort

Science.gov (United States)

Wright, Rick W.; Huston, Laura J.; Haas, Amanda K.; Spindler, Kurt P.; Nwosu, Sam K.; Allen, Christina R.; Anderson, Allen F.; Cooper, Daniel E.; DeBerardino, Thomas M.; Dunn, Warren R.; Lantz, Brett (Brick) A.; Stuart, Michael J.; Garofoli, Elizabeth A.; Albright, John P.; Amendola, Annunziato (Ned); Andrish, Jack T.; Annunziata, Christopher C.; Arciero, Robert A.; Bach, Bernard R.; Baker, Champ L.; Bartolozzi, Arthur R.; Baumgarten, Keith M.; Bechler, Jeffery R.; Berg, Jeffrey H.; Bernas, Geoffrey A.; Brockmeier, Stephen F.; Brophy, Robert H.; Bush-Joseph, Charles A.; Butler, J. Brad; Campbell, John D.; Carey, James L.; Carpenter, James E.; Cole, Brian J.; Cooper, Jonathan M.; Cox, Charles L.; Creighton, R. Alexander; Dahm, Diane L.; David, Tal S.; Flanigan, David C.; Frederick, Robert W.; Ganley, Theodore J.; Gatt, Charles J.; Gecha, Steven R.; Giffin, James Robert; Hame, Sharon L.; Hannafin, Jo A.; Harner, Christopher D.; Harris, Norman Lindsay; Hechtman, Keith S.; Hershman, Elliott B.; Hoellrich, Rudolf G.; Hosea, Timothy M.; Johnson, David C.; Johnson, Timothy S.; Jones, Morgan H.; Kaeding, Christopher C.; Kamath, Ganesh V.; Klootwyk, Thomas E.; Levy, Bruce A.; Ma, C. Benjamin; Maiers, G. Peter; Marx, Robert G.; Matava, Matthew J.; Mathien, Gregory M.; McAllister, David R.; McCarty, Eric C.; McCormack, Robert G.; Miller, Bruce S.; Nissen, Carl W.; O'Neill, Daniel F.; Owens, Brett D.; Parker, Richard D.; Purnell, Mark L.; Ramappa, Arun J.; Rauh, Michael A.; Rettig, Arthur C.; Sekiya, Jon K.; Shea, Kevin G.; Sherman, Orrin H.; Slauterbeck, James R.; Smith, Matthew V.; Spang, Jeffrey T.; Svoboda, Steven J.; Taft, Timothy N.; Tenuta, Joachim J.; Tingstad, Edwin M.; Vidal, Armando F.; Viskontas, Darius G.; White, Richard A.; Williams, James S.; Wolcott, Michelle L.; Wolf, Brian R.; York, James J.

2015-01-01

Background Most surgeons believe that graft choice for ACL reconstruction is an important factor related to outcome. Although graft choice may be limited in the revision setting based on previously used grafts, it is still felt to be important. Hypothesis The purpose of this study was to determine if revision ACL graft choice predicts outcomes related to sports function, activity level, OA symptoms, graft re-rupture, and reoperation at two years following revision reconstruction. We hypothesized that autograft use would result in increased sports function, increased activity level, and decreased OA symptoms (as measured by validated patient reported outcome instruments). Additionally, we hypothesized that autograft use would result in decreased graft failure and reoperation rate 2 years following revision ACL reconstruction. Study Design Prospective cohort study; Level of evidence, 2. Methods Revision ACL reconstruction patients were identified and prospectively enrolled by 83 surgeons over 52 sites. Data collected included baseline demographics, surgical technique and pathology, and a series of validated patient reported outcome instruments (IKDC, KOOS, WOMAC, and Marx activity rating score). Patients were followed up at 2 years, and asked to complete the identical set of outcome instruments. Incidence of additional surgery and reoperation due to graft failure were also recorded. Multivariate regression models were used to determine the predictors (risk factors) of IKDC, KOOS, WOMAC, Marx scores, graft re-rupture, and reoperation rate at 2 years following revision surgery. Results 1205 patients were successfully enrolled with 697 (58%) males. Median age was 26. In 88% this was their first revision. 341 (28%) were undergoing revision by the surgeon that had performed the previous reconstruction. 583 (48%) underwent revision reconstruction utilizing an autograft, 590 (49%) allograft, and 32 (3%) both autograft and allograft. Median time since their last ACL

What Is the Rerevision Rate After Revising a Hip Resurfacing Arthroplasty? Analysis From the AOANJRR.

Science.gov (United States)

Wong, James Min-Leong; Liu, Yen-Liang; Graves, Stephen; de Steiger, Richard

2015-11-01

More than 15,000 primary hip resurfacing arthroplasties have been recorded by the Australian Orthopaedic Association National Joint Replacement Registry (AOANJRR) with 884 primary procedures requiring revision for reasons other than infection, a cumulative percent revision rate at 12 years of 11%. However, few studies have reported the survivorship of these revision procedures. (1) What is the cumulative percent rerevision rate for revision procedures for failed hip resurfacings? (2) Is there a difference in rerevision rate among different types of revision or bearing surfaces? The AOANJRR collects data on all primary and revision hip joint arthroplasties performed in Australia and after verification against health department data, checking of unmatched procedures, and subsequent retrieval of unreported procedures is able to obtain an almost complete data set relating to hip arthroplasty in Australia. Revision procedures are linked to the known primary hip arthroplasty. There were 15,360 primary resurfacing hip arthroplasties recorded of which 884 had undergone revision and this was the cohort available to study. The types of revisions were acetabular only, femoral only, or revision of both acetabular and femoral components. With the exception of the acetabular-only revisions, all revisions converted hip resurfacing arthroplasties to conventional (stemmed) total hip arthroplasties (THAs). All initial revisions for infection were excluded. The survivorship of the different types of revisions and that of the different bearing surfaces used were estimated using the Kaplan-Meier method and compared using Cox proportional hazard models. Cumulative percent revision was calculated by determining the complement of the Kaplan-Meier survivorship function at that time multiplied by 100. Of the 884 revisions recorded, 102 underwent further revision, a cumulative percent rerevision at 10 years of 26% (95% confidence interval, 19.6-33.5). There was no difference in the rate of

40 CFR 60.2155 - May I conduct performance testing less often?

Science.gov (United States)

2010-07-01

... performance test. (c) If a performance test shows a deviation from an emission limitation for particulate... 40 Protection of Environment 6 2010-07-01 2010-07-01 false May I conduct performance testing less... PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for...

Tools to Ensure Safe Medicines: New Monograph Tests in USP-NF

Directory of Open Access Journals (Sweden)

Catherine Sheehan

2010-06-01

Full Text Available This paper describes USP-NF compendial updates to six ‘high-priority” excipient monographs: Glycerin, Propylene Glycol, Sorbitol Solution, Sorbitol Sorbitan Solution, Noncrystallizing Sorbitol Solution and Maltitol Solution. The USP-NF revisions arose from the Food and Drug Administration’s (FDA’s requests to include, as part of each monograph’s Identification test, a limit test to detect the presence of Diethylene Glycol (DEG, a toxic adulterant. These revisions align with the 2007 FDA Guidance for Industry: Testing of Glycerin for Diethylene Glycol (1, that drug product manufacturers perform a specific identity test for DEG on all containers of all lots of glycerin before glycerin is used in the manufacture and preparation of drug products. This paper describes several risk factors due to a complex global excipient supply chain, nonspecific specifications, inadequate supply chain qualification, and poor understanding of regulations. Strengthening and conformance to compendial specifications is one of the tools necessary to mitigate risk and help prevent the next DEG adulteration that is part of USP’s efforts to ensure safe medicines.

Performance testing SPECT systems: Recent developments

International Nuclear Information System (INIS)

Todd-Pokropek, A.

1985-01-01

A protocol is used to test as many currently available systems as possible, including both rotating gamma camera systems from GE, Siemens, Toshiba, Technicare, Elscint, Philips, Picker, etc, and single/multi slice system such as the Medimatic. This paper indicates changes that have occurred with respect to preliminary results previously published. Reconstructions were performed in a standard manner, using a Ramp filter and without attenuation correction, in order to reduce the effect of differences in software. The Jaszczak phantom was used to assess overall image quality. Tests were performed using the different collimators available. Image quality improved with better spatial resolution, even at the expense of sensitivity. Non-circular orbits, where available, were tested, and resolution was comparing for various positions and directions. With double headed systems, the results obtained were compared to those using a single head alone. Some gain in image quality seems to have been achieved by better uniformity resulting from improved correction circuitry, by the use of non-circular orbits, and from scatter correction. Potential still exists to improve collimator design

Short-term survival of the trabecular metal cup is similar to that of standard cups used in acetabular revision surgery.

Science.gov (United States)

Mohaddes, Maziar; Rolfson, Ola; Kärrholm, Johan

2015-02-01

The use of trabecular metal (TM) cups in revision surgery has increased worldwide during the last decade. Since the introduction of the TM cup in Sweden in 2006, this design has gradually replaced other uncemented designs used in Sweden. According to data from the Swedish Hip Arthroplasty Register (SHAR) in 2012, one-third of all uncemented first-time cup revisions were performed using a TM cup. We compared the risk of reoperation and re-revision for TM cups and the 2 other most frequently used cup designs in acetabular revisions reported to the SHAR. The hypothesis was that the performance of TM cups is as good as that of established designs in the short term. The study population consisted of 2,384 patients who underwent 2,460 revisions during the period 2006 through 2012. The most commonly used cup designs were the press-fit porous-coated cup (n = 870), the trabecular metal cup (n = 805), and the cemented all-polyethylene cup (n = 785). 54% of the patients were female, and the median age at index revision was 72 (19-95) years. Reoperation was defined as a second surgical intervention, and re-revision-meaning exchange or removal of the cup-was used as endpoint. The mean follow-up time was 3.3 (0-7) years. There were 215 reoperations, 132 of which were re-revisions. The unadjusted and adjusted risk of reoperation or re-revision was not significantly different for the TM cup and the other 2 cup designs. Our data support continued use of TM cups in acetabular revisions. Further follow-up is necessary to determine whether trabecular metal cups can reduce the re-revision rate in the long term, compared to the less costly porous press-fit and cemented designs.

Individual differences in infant fearfulness and cognitive performance: a testing, performance, or competence effect?

Science.gov (United States)

Rieser-Danner, Loretta A

2003-02-01

The author conducted 2 studies to examine the relations between infant fear and cognitive testing performance in 12-month-old infants. In Study 1, fear was assessed by using 2 standard temperament questionnaires and a laboratory-based, standardized stranger approach. Individual differences in cognitive development were assessed using the Object Permanence Scale of the Infant Psychological Development Scales (I. C. Uzgiris & J. M. Hunt, 1975). All 3 assessments of fear significantly predicted object permanence performance, with correlations ranging from -.32 to -.35. In Study 2, fear was assessed via a maternal report questionnaire, and habituation performance was assessed via a basic-level categorization task. Familiarity with the examiner and with the testing environment was manipulated to test for a familiarity influence on performance. Testing revealed individual differences in both fear and habituation. Results suggest that highly fearful infants required more trials to habituate and were less likely to meet the habituation criterion than infants who were less fearful. Methodological and conceptual implications of these results are discussed.

Increased risk of revision for infection in rheumatoid arthritis patients with total hip replacements

DEFF Research Database (Denmark)

Schrama, Johannes Cornelis; Fenstad, Anne M; Dale, Håvard

2015-01-01

Background and purpose-Medical treatment of rheumatoid arthritis (RA) has changed dramatically over the last 15 years, including immune modulation. We investigated the risk of revision for infection after primary total hip replacement (THR) in patients with rheumatoid arthritis over a 16-year...... period, and compared it with that in THR patients with osteoarthritis (OA).Patients and methods-We identified 13,384 THRs in RA patients and 377,287 THRs in OA patients from 1995 through 2010 in a dataset from the Nordic Arthroplasty Register Association (NARA). Kaplan-Meier survival curves......, with revision for infection as the endpoint, were constructed. Cox regression analyses were performed to calculate the relative risk (RR) of revision for infection adjusted for age, sex, fixation technique, and year of primary surgery.Results-RA patients had a 1.3 times (95% CI 1.0-1.6) higher risk of revision...

Impact of Fibromyalgia in the Sit-to-Stand-to-Sit Performance Compared With Healthy Controls.

Science.gov (United States)

Collado-Mateo, Daniel; Adsuar, Jose C; Dominguez-Muñoz, Francisco J; Olivares, Pedro R; Gusi, Narcis

2017-06-01

Fibromyalgia is associated with a reduction in the ability to perform activities of daily living. Sit-to-stand-to-sit performance is one of the most common activities of daily living and often is evaluated by counting the number of repetitions of the 30-second chair-stand test. No study, however, has examined the performance over the 30 seconds of this test of female patients with fibromyalgia on a phase-by-phase basis. To evaluate the impact of fibromyalgia on performance of the 30-second chair-stand test and to analyze how the kinematic performance changed over the 30-second test period. A cross-sectional study. Local association of fibromyalgia. Fifteen females with fibromyalgia and nine healthy female controls. Participants performed the 30-second chair-stand test while wearing a motion capture device. Duration of each sit-to-stand-to-sit phase within the 30-second time limit was compared between groups using repeated measures analysis of variance. The association between duration of phases and scores from the revised version of the Fibromyalgia Impact Questionnaire was tested using bivariate correlations. The duration of impulse and sit-to-stand phases were gradually increased over the 30 seconds of the chair-stand test for women with fibromyalgia compared with healthy controls (P = .04 and P = .02, respectively). The mean duration of these 2 phases was associated with symptom duration and the function domain of the revised version of the Fibromyalgia Impact Questionnaire (P fibromyalgia and healthy controls. Since sit-to-stand from a chair is a common daily activity, women with fibromyalgia may require specific exercises to improve performance of this task. Not applicable. Copyright © 2017 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

Artificial urinary sphincter revision for urethral atrophy: comparing single cuff downsizing and tandem cuff placement

Directory of Open Access Journals (Sweden)

Brian J. Linder

Full Text Available ABSTRACT Objective To compare outcomes for single urethral cuff downsizing versus tandem cuff placement during artificial urinary sphincter (AUS revision for urethral atrophy. Materials and Methods We identified 1778 AUS surgeries performed at our institution from 1990-2014. Of these, 406 were first AUS revisions, including 69 revisions for urethral atrophy. Multiple clinical and surgical variables were evaluated for potential association with device outcomes following revision, including surgical revision strategy (downsizing a single urethral cuff versus placing tandem urethral cuffs. Results Of the 69 revision surgeries for urethral atrophy at our institution, 56 (82% were tandem cuff placements, 12 (18% were single cuff downsizings and one was relocation of a single cuff. When comparing tandem cuff placements and single cuff downsizings, the cohorts were similar with regard to age (p=0.98, body-mass index (p=0.95, prior pelvic radiation exposure (p=0.73 and length of follow-up (p=0.12. Notably, there was no difference in 3-year overall device survival compared between single cuff and tandem cuff revisions (60% versus 76%, p=0.94. Likewise, no significant difference was identified for tandem cuff placement (ref. single cuff when evaluating the risk of any tertiary surgery (HR 0.95, 95% CI 0.32-4.12, p=0.94 or urethral erosion/device infection following revision (HR 0.79, 95% CI 0.20-5.22, p=0.77. Conclusions There was no significant difference in overall device survival in patients undergoing single cuff downsizing or tandem cuff placement during AUS revision for urethral atrophy.

[Osteosynthesis and cup revision in periprosthetic acetabulum fractures using a Kocher-Langenbeck approach].

Science.gov (United States)

Schwabe, P; Märdian, S; Perka, C; Schaser, K-D

2016-04-01

Reconstruction/stable fixation of the acetabular columns to create an adequate periacetabular requirement for the implantation of a revision cup. Displaced/nondisplaced fractures with involvement of the posterior column. Resulting instability of the cup in an adequate bone stock situation. Periprosthetic acetabulum fractures with inadequate bone stock. Extended periacetabular defects with loss of anchorage options. Isolated periprosthetic fractures of the anterior column. Septic loosening. Dorsal approach. Dislocation of hip. Mechanical testing of inlaying acetabular cup. With unstable cup situation explantation of the cup, fracture fixation of acetabulum with dorsal double plate osteosynthesis along the posterior column. Cup revision. Hip joint reposition. Early mobilization; partial weight bearing for 12 weeks. Thrombosis prophylaxis. Clinical and radiological follow-ups. Periprosthetic acetabular fracture in 17 patients with 9 fractures after primary total hip replacement (THR), 8 after revision THR. Fractures: 12 due to trauma, 5 spontaneously; 7 anterior column fractures, 5 transverse fractures, 4 posterior column fractures, 1 two column fracture after hemiendoprosthesis. 5 type 1 fractures and 12 type 2 fractures. Operatively treated cases (10/17) received 3 reinforcement ring, 2 pedestal cup, 1 standard revision cup, cup-1 cage construct, 1 ventral plate osteosynthesis, 1 dorsal plate osteosynthesis, and 1 dorsal plate osteosynthesis plus cup revision (10-month Harris Hip Score 78 points). Radiological follow-up for 10 patients: consolidation of fractures without dislocation and a fixed acetabular cup. No revision surgeries during follow-up; 2 hip dislocations, 1 transient sciatic nerve palsy.

[An overview on the collation and revision of medical books by the Bureau for Revising Medical Books in the Northern Song Dynasty].

Science.gov (United States)

Meng, Yongliang; Liang, Yongxuan

2014-07-01

The Bureau for Revising Medical Books was a temporary agency established by the government of the Northern Song Dynasty in 1057, the 2nd year of Jiayou of Emperor Renzong, exclusively for the edition, revision and publishing of ancient medical books. 11 medical books were revised and edited by 13 Bureau members in a period of 12 years until 1069, the 2nd year of Xining of Emperor ShenZong, which eventually became the final versions until today. 8 medical books were initially planned for the revision, but 11 were actually completed in the end. The time for completing a revision varied from over 10 years at most to less than 1 year at least. Instead of working in the office, the officers of the Bureau for Revising Medical Books did their works at home. The members of the said Bureau came from the Tiju officer of the Bureau for Revising Medical Books and the officials of revising medical books, consisting of both Confucian ministers and medical officers. Confucian ministers played an important role in revising medical books. The Bureau had a strict workflow in electing revising officials, making the project, and the determination of the principles and arrangements of the tasks of editing and proofreading.

Revision of Krsko NPP Quality Assurance Plan

International Nuclear Information System (INIS)

Biscan, R.; Fifnja, I.; Kavsek, D.

2012-01-01

International standards from nuclear power plant operation area are being frequently upgraded and revised in accordance with the continuous improvement philosophy. This philosophy applies also to the area of Quality Assurance, which has also undergone significant improvement since the early 1950s. Besides just nuclear industry, there are also other international quality standards that are being continuously developed and revised, bringing needs for upgrades also in the nuclear application. Since the beginning of Krsko NPP construction, the overall Quality Assurance program and its applicable procedures were in place to assure that all planned and systematic actions necessary to provide adequate confidence that an item or service will satisfy given requirements to quality, are in place. The overall requirements for quality as one of the major objectives for Krsko NPP operation are also set forth in the Updated Safety Analyses Report, the document that serves as a base for operating license. During more than 30 years of Krsko NPP operation, the quality requirements and related documents were revised and upgraded in several attempts. The latest revision 6 of QD-1, Quality Assurance Plan was issued during the year 2011. The bases for the revision were: Changes of the Slovenian regulatory requirements (ZVISJV, JV5, JV9?), Changes of Krsko NPP licensing documents (USAR section 13?), SNSA inspection requirements, Changes of international standards (IAEA, ISO?), Conclusions of first PSR, Implementation of ISO standards in Krsko NPP (ISO14001, ISO17025), Changes of plant procedures, etc. One of the most obvious changes was the enlargement of the QA Plan scope to cover interdisciplinary areas defined in the plant management program MD-1, such as Safety culture, Self-assessment, Human performance, Industrial Safety etc. The attachment of the QA Plan defining relationships between certain standards was also updated to provide matrix for better correlation of requirements of

DPM PERFORMANCE TESTING USING RASPBERRY PIS

CERN Document Server

Regala, M

2013-01-01

This is the final report from attending CERN’s Summer Student Programme. The project goal was to do performance testing on the Disk Pool Manager (DPM), a lightweight, reliable, grid-aware storage software used to store and retrieve data produced by CERN’s LHC experiments using the small, low-end ARM powered devices named Raspberry Pis. The idea behind it was to reason if it’s possible to use a cluster of lower-end, under-capable devices to run DPM, and to conclude if it would be more energy efficient than running it on oversized machines, with the same or comparable performance. If this hypothesis was true, the power-hungry machines could be ditched in favour of these small devices, leading to an enormous saving in overall power consumption and hence, overall cost. In this report, I describe what was the initial project goal and intended outcomes, proceeding to explain the underlying technologies used. Afterwards, I’ll explain the setup used, the tests performed, and the conclusions reached. iii

A revised mineral nutrient supplement increases biomass and growth rate in Chlamydomonas reinhardtii.

Science.gov (United States)

Kropat, Janette; Hong-Hermesdorf, Anne; Casero, David; Ent, Petr; Castruita, Madeli; Pellegrini, Matteo; Merchant, Sabeeha S; Malasarn, Davin

2011-06-01

Interest in exploiting algae as a biofuel source and the role of inorganic nutrient deficiency in inducing triacylglyceride (TAG) accumulation in cells necessitates a strategy to efficiently formulate species-specific culture media that can easily be manipulated. Using the reference organism Chlamydomonas reinhardtii, we tested the hypothesis that modeling trace element supplements after the cellular ionome would result in optimized cell growth. We determined the trace metal content of several commonly used Chlamydomonas strains in various culture conditions and developed a revised trace element solution to parallel these measurements. Comparison of cells growing in the revised supplement versus a traditional trace element solution revealed faster growth rates and higher maximum cell densities with the revised recipe. RNA-seq analysis of cultures growing in the traditional versus revised medium suggest that the variation in transcriptomes was smaller than that found between different wild-type strains grown in traditional Hutner's supplement. Visual observation did not reveal defects in cell motility or mating efficiency in the new supplement. Ni²⁺-inducible expression from the CYC6 promoter remained a useful tool, albeit with an increased requirement for Ni²⁺ because of the introduction of an EDTA buffer system in the revised medium. Other advantages include more facile preparation of trace element stock solutions, a reduction in total chemical use, a more consistent batch-to-batch formulation and long-term stability (tested up to 5 years). Under the new growth regime, we analyzed cells growing under different macro- and micronutrient deficiencies. TAG accumulation in N deficiency is comparable in the new medium. Fe and Zn deficiency also induced TAG accumulation, as suggested by Nile Red staining. This approach can be used to efficiently optimize culture conditions for other algal species to improve growth and to assay cell physiology. © 2011 The Authors

Test objects for evaluating the performance of radiological imaging systems. Leeds radiological test objects

International Nuclear Information System (INIS)

Cowen, A.R.; Clarke, O.F.; Haywood, J.M.; Parker, R.P.

1985-01-01

A range of test objects has been developed to assess the imaging performance of conventional and digital radiological imaging systems. These test objects have arisen as a result of involvement in both the laboratory evaluation of radiological imaging systems and the routine maintenance of such equipment in a large diagnostic radiology department. The philosophy behind the design and application of the test objects is briefly described. Particular attention is paid to the advantages of using the threshold-contrast detail-detectability technique to assess overall imaging performance. The great importance of ensuring optimum imaging performance prior to clinical acceptance is stressed. A strategy for implementing the test objects in a clinical department is present. The diagnostic information content of the clinical images which result measures the success of the quality control procedure adopted. (author)

Extraction, Scrub, and Strip Test Results for the Salt Waste Processing Facility Caustic Side Solvent Extraction Solvent Sample

Energy Technology Data Exchange (ETDEWEB)

Peters, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-10-06

An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D(_Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D(_Cs) measured 12.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges. This revision was created to correct an error. The previous revision used an incorrect set of temperature correction coefficients which resulted in slight deviations from the correct D(_Cs) results.