An emissions audit of a biomass combustor burning treated wood waste

International Nuclear Information System (INIS)

Jackson, P.M.; Jones, H.H.; King, P.G.

1993-01-01

This report describes the Emissions Audit carried out on a Biomass Combustor burning treated wood waste at the premises of a furniture manufacturer. The Biomass Combustor was tested in two firing modes; continuous fire and modulating fire. Combustion chamber temperatures and gas residence times were not measured. Boiler efficiencies were very good at greater than 75% in both tests. However, analysis of the flue gases indicated that improved efficiencies are possible. The average concentrations of CO (512mgm -3 ) and THC (34mgm -3 ) for Test 1 were high, indicating that combustion was poor. The combustor clearly does not meet the requirements of the Guidance Note for the Combustion of Wood Waste. CO 2 and O 2 concentrations were quite variable showing that combustion conditions were fairly unstable. Improved control of combustion should lead to acceptable emission concentrations. (Author)

Inventory of contaminants in waste wood; Inventering av foeroreningar i returtrae

Energy Technology Data Exchange (ETDEWEB)

Jermer, Joeran; Ekvall, Annika; Tullin, Claes [Swedish National Testing and Research Inst., Boraas (Sweden)

2001-03-01

Waste wood is increasingly used as fuel in Sweden. It is of Swedish origin as well as imported, mainly from Germany and the Netherlands. The waste wood is contaminated by e.g. paint and wood preservatives and objects of metal, glass, plastics etc. The contaminants may cause technical problems such as deposits and corrosion as well as plugging of air openings. The present study has focussed on potential contaminants in waste wood that could cause problems of technical as well as environmental nature. The major chemical contaminants are surface treatments (paints etc) and wood preservatives. The surface treatments contribute in particular to contaminants of zinc and lead. In some cases zinc has been found to cause severe deposits in the furnaces. Surface treatments also contribute to increased levels of sodium, chlorine, sulphur and nitrogen. Preservative-treated wood is the most important source of increased levels of copper, chromium and arsenic in the waste wood. Waste wood imported from Germany contains less arsenic but the same amount of copper and chromium as Swedish waste wood. The contents of mercury in German waste wood can be expected to be higher than in waste wood of Swedish origin. The fraction consisting of wood-based panels is comparably free from contaminants but as a result of the high contents of adhesives wood-based panels contribute to a higher proportion of nitrogen in waste wood than in forest residues. A great number of non-wood compounds (such as plastics and metals) do also contaminate waste wood. By careful and selective demolition and various sorting procedures most non-wood compounds will be separated from the waste wood. Waste sorting analyses carried out indicate that the waste wood contains approximately 1% non-wood compounds, mainly plastic and metal compounds, glass, dirt, concrete, bricks and gypsum. This may seem to be a small proportion, but if large amounts of waste wood are incinerated the non-wood compounds will inevitably cause

Absorption study of pentachlorophenol in persons working with wood preservatives

Energy Technology Data Exchange (ETDEWEB)

Jones, R.D.; Winter, D.P.; Cooper, A.J.

1986-05-01

Plasma and urinary pentachlorophenol (PCP) was measured in 209 workers who had occupational exposure to wood preservatives containing this compound and 101 workers not exposed occupationally to PCP. Workers were examined for chloracne and blood concentrations of bilirubin, gamma-glutamyltransferase (GGT), cholesterol and high-density lipoproteins (HDL) were determined. All the occupationally exposed groups showed evidence of PCP absorption; highest mean concentrations were found in remedial timber-treatment operatives (6.0 mmol/l for plasma and 274 nmol/mmol of creatinine for urine). Timber-yard workers also showed substantial evidence of absorption (mean plasma concentration 4.8 mmol/l). Persons formulating PCP-containing wood preservatives had the lowest concentrations of any exposed group sampled (mean plasma concentration 1.3 mmol/l, mean urinary concentration 39.6 nmol/mmol of creatinine). The occupational groups studied were not standardized for factors known to affect bilirubin, GGT, cholesterol and HDL. The inference that can be drawn from the results of these measurements is therefore limited. There was, however, no evidence of any disadvantageous effect of PCP on health as measured by these parameters. No overt case of chloracne was found.

Counter-current acid leaching process for copper azole treated wood waste.

Science.gov (United States)

Janin, Amélie; Riche, Pauline; Blais, Jean-François; Mercier, Guy; Cooper, Paul; Morris, Paul

2012-09-01

This study explores the performance of a counter-current leaching process (CCLP) for copper extraction from copper azole treated wood waste for recycling of wood and copper. The leaching process uses three acid leaching steps with 0.1 M H2SO4 at 75degrees C and 15% slurry density followed by three rinses with water. Copper is recovered from the leachate using electrodeposition at 5 amperes (A) for 75 min. Ten counter-current remediation cycles were completed achieving > or = 94% copper extraction from the wood during the 10 cycles; 80-90% of the copper was recovered from the extract solution by electrodeposition. The counter-current leaching process reduced acid consumption by 86% and effluent discharge volume was 12 times lower compared with the same process without use of counter-current leaching. However, the reuse of leachates from one leaching step to another released dissolved organic carbon and caused its build-up in the early cycles.

State-of-the-art of the European regulation on wood wastes and wood ashes valorization. Synthesis

International Nuclear Information System (INIS)

Mousseau, S.

2007-01-01

This study has the objective of comparing the regulations of 10 European countries with that of France, in relation to the classification and recycling of wood waste, in particular lightly treated wood, as well as recycling of wood ash. The first part relating to wood waste presents a detailed analysis by country as well as a summary, on the one hand, of the various sectors for recycling waste wood and, on the other, the emission limits for their energy recovery. Generally, there is a distinction between waste covered by the incineration directive, and the others, without any particular category for lightly treated wood. However, recommendations emerge from this that are based essentially on the regulations or guidelines observed in Germany, Austria and the United Kingdom. The second part relating to wood ash also a presents a detailed analysis by country as well as a summary of the various sectors of recycling and limit values for spreading. Ash is generally considered as waste, and is recycled on a case-by case basis. Only Germany and Austria have clearly integrated wood ash in their regulatory framework. Overall this study shows the need for uniform regulation at European level, establishing environment requirements for recycling wood waste and wood ash, in order to encourage development of the use of biomass

Bond quality of phenol-based adhesives containing liquefied creosote-treated wood

Science.gov (United States)

Chung-Yun Hse; Feng Fu; Hui Pan

2009-01-01

Liquefaction of spent creosote-treated wood was studied to determine the technological practicability of its application in converting treated wood waste into resin adhesives. A total of 144 plywood panels were fabricated with experimental variables included 2 phenol to wood (P/W) ratios in liquefaction, 6 resin formulations (3 formaldehyde/liquefied wood (F/...

Emissions of toxic pollutants from co-combustion of demolition and construction wood and household waste fuel blends.

Science.gov (United States)

Edo, Mar; Ortuño, Núria; Persson, Per-Erik; Conesa, Juan A; Jansson, Stina

2018-07-01

Four different types of fuel blends containing demolition and construction wood and household waste were combusted in a small-scale experimental set-up to study the effect of fuel composition on the emissions of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), biphenyls (PCBs), chlorobenzenes (PCBzs), chlorophenols (PCPhs) and polycyclic aromatic hydrocarbons (PAHs). Two woody materials, commercial stemwood (ST) and demolition and construction wood (DC) were selected because of the differences in their persistent organic pollutants (POPs), ash and metals content. For household waste, we used a municipal solid waste (MSW) and a refuse-derived fuel (RDF) from MSW with 5-20 wt% and up to 5 wt% food waste content respectively. No clear effect on the formation of pollutants was observed with different food waste content in the fuel blends tested. Combustion of ST-based fuels was very inefficient which led to high PAH emissions (32 ± 3.8 mg/kg fuel ). The use of DC clearly increased the total PCDD and PCDF emissions (71 ± 26 μg/kg fuel ) and had a clear effect on the formation of toxic congeners (210 ± 87 ng WHO 2005 -TEQ/kg fuel ). The high PCDD and PCDF emissions from DC-based fuels can be attributed to the presence of material contaminants such as small pieces of metals or plastics as well as timber treated with chromated copper arsenate preservatives and pentachlorophenol in the DC source. Copyright © 2018 Elsevier Ltd. All rights reserved.

IN SITU BIOREMEDIATION STRATEGIES FOR ORGANIC WOOD PRESERVATIVES

Science.gov (United States)

Laboratory biotreatability studies evaluated the use of bioventing and biosparging plus groundwater circulation (UVB technology) for their potential abililty to treat soil and groundwater containing creosote and pentachlorophenol. Soils from two former wood-treatment facilities w...

Life cycle environmental impacts of different construction wood waste and wood packaging waste processing methods

OpenAIRE

Manninen, Kaisa; Judl, Jáchym; Myllymaa, Tuuli

2016-01-01

This study compared the life cycle environmental impacts of different wood waste processing methods in three impact categories: climate impact, acidification impacts and eutrophication impacts. The wood waste recovery methods examined were the use of wood waste in terrace boards made out of wood composite which replace impregnated terrace boards, incineration of wood waste in a multi-fuel boiler instead of peat and the use of wood waste in the production of particleboard in either Finland or ...

Urban Wood Waste Resource Assessment

Energy Technology Data Exchange (ETDEWEB)

Wiltsee, G.

1998-11-20

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

Exposure assessment of residents living near a wood treatment plant

International Nuclear Information System (INIS)

Dahlgren, James; Warshaw, Raphael; Horsak, Randy D.; Parker, Frank M. III; Takhar, Harpreet

2003-01-01

We report the results of environmental sampling and modeling in a neighborhood adjacent to a wood processing plant. This plant used creosote and pentachlorophenol (PCP) to treat wood for over 70 years. Between 1999 and 2001, environmental samples were obtained to quantify the level of environmental contamination from the wood processing plant. Blood from 10 residents was measured for chlorinated dioxins and dibenzofurans. Soil sediment samples from drainage ditches and attic/dust samples from nearby residents' homes were tested for polychlorinated dioxins, furans, and polycyclic aromatic hydrocarbons (PAH). The dioxin congeners analysis of the 10 residents revealed elevated valued for octachlorodibenzo-p-dioxin and heptachlorodibenzo-p-dioxin compatible with PCP as the source. The levels of carcinogenic PAHs were higher than background levels and were similar to soil contamination on wood preserving sites. Wipe sampling in the kitchens of 11 homes revealed that 20 of the 33 samples were positive for octachlorinated dioxins with a mean value of 10.27 ng/m 2 . The soil, ditch samples, and positive wipe samples from the homes indicate a possible ongoing route of exposure to the contaminants in the homes of these residents. Modeled air exposure estimated for the wood processing waste chemicals indicate some air exposure to combustion products. The estimated air levels for benzo(a)pyrene and tetrachlorodibenzodiozin in this neighborhood exceeded the recommended levels for these compounds in some states. The quantitative data presented suggest a significant contamination of a neighborhood by wood processing waste chemicals. These findings suggest the need for more stringent regulations on waste discharges from wood treatment plants

Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

DEFF Research Database (Denmark)

Pedersen, Anne Juul; Ottosen, Lisbeth M.

2006-01-01

Element distribution in a combined fly ash and bottom ash from combustion of copper chromate arsenate (CCA) treated wood waste was investigated by scanning electron microscopy (SEM/EDX) before and after electrodialytic extraction. The untreated ash contained various particles, including pieces...... of incompletely combusted wood rich in Cr and Ca, and irregular particles rich in Si, Al and K. Cr was also found incorporated in silica-based matrix particles. As was associated with Ca in porous (char) particles, indicating that Ca-arsenates had been formed during combustion. Cu was associated with Cr...... in the incompletely combusted wood pieces and was also found in almost pure form in a surface layer of some matrix particles – indicating surface condensation of volatile Cu species. In treated ash, Ca and As were no longer found together, indicating that Ca-arsenates had been dissolved due to the electrodialytic...

Chemical degradation of pentachlorophenol

International Nuclear Information System (INIS)

Shukla, S.S.; Shukla, A.; Chandrasekharaiah, M.S.

1992-01-01

Industry produces a large volume of hazardous wastes containing pentachlorophenol, a U.S. EPA priority hazardous organic material. The environmentally safe disposal of these PCP-contaminated wastes is a serious problem for the waste management authorities as the current treatment processes are unsatisfactory. In this paper, the results of a feasibility study of chemical degradation and/or solidification methods for PCP-containing wastes. The photochemical decomposition of the PCP in a microemulsion or in micellar media obtained with the help of SDS or CTAB show the greatest promise

Wood wastes: Uses

International Nuclear Information System (INIS)

Cipro, A.

1993-01-01

The 1,500 industrial firms manufacturing furniture in the Italian Province of Treviso can generate up to 190,000 tonnes of wood wastes annually. In line with the energy conservation-environmental protection measures contained in Italian Law No. 475/88, this paper indicates convenient uses for these wood wastes - as a raw material for fibreboards or as a fuel to be used in the furniture manufacturing plants themselves and in kilns producing lime. Reference is made to the wood wastes gasification/power generation system being developed by ENEA (the Italian Agency for New Technology, Energy and the Environment)

Sustainable wood waste management in Nigeria

Directory of Open Access Journals (Sweden)

Owoyemi Jacob Mayowa

2016-09-01

Full Text Available Wood industries produce large volumes of residues which must be utilized, marketed or properly disposed of. Heaps of wood residues are common features in wood industries throughout the year. In Nigeria, this residue is generally regarded as waste and this has led to open burning practices, dumping in water bodies or dumping in an open area which constitutes environmental pollution. Sawmills in Nigeria generated over 1,000,000 m3 of wood waste in 2010 while about 5000 m3 of waste was generated in plywood mills. Nigeria generates about 1.8 million tons of sawdust annually and 5.2 million tons of wood wastes. The impact of improper disposal of waste wood on the environment affects both the aquatic and terrestrial ecosystems. Also burning of waste wood releases greenhouse gases into the atmosphere causing various health issues. Reuse/recycling of these wood residues in Nigeria will reduce the pressure on our ever decreasing forests, reduce environmental pollution, create wealth and employment. The literature available on this subject was reviewed and this article, therefore, focuses on the various methods of wood waste disposal and its utilization in Nigerian wood industries, the effects of wood waste on the environment as well as on human health and the benefits of proper wood waste management practices.

Urban Wood Waste Resource Assessment; TOPICAL

International Nuclear Information System (INIS)

Wiltsee, G.

1998-01-01

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris

A Study on the Effect of Plasma Treatment for Waste Wood Biocomposites

Directory of Open Access Journals (Sweden)

MiMi Kim

2013-01-01

Full Text Available The surface modification of wood powder by atmospheric pressure plasma treatment was investigated. The composites were manufactured using wood powder and polypropylene (wood powder: polypropylene = 55 wt% : 45 wt%. Atmospheric pressure plasma treatment was applied under the condition of 3 KV, 17±1 KHz, 2 g/min. Helium was used as the carrier gas and hexamethyl-disiloxane (HMDSO as the monomer to modify the surface property of the waste wood biocomposites by plasma polymerization. The tensile strengths of untreated waste wood powder (W3 and single species wood powder (S3 were about 18.5 MPa and 21.5 MPa while those of plasma treated waste wood powder (PW3 and plasma treated single species wood powder (PS3 were about 21.2 MPa and 23.4 MPa, respectively. Tensile strengths of W3 and S3 were improved by 14.6% and 8.8%, respectively. From the analyses of mechanical properties and morphology, we conclude that the interfacial bonding of polypropylene and wood powder can be improved by atmospheric pressure plasma treatment.

Assessment of the wood waste resource and its position in the wood / wood-energy sector - Synthesis

International Nuclear Information System (INIS)

Guinard, Ludovic; Deroubaix, Gerard; Roux, Marie-Lise; Levet, Anne-Laure; Quint, Vincent

2015-04-01

The first objective of this study is to obtain a better knowledge of the 'wood wastes' issue, to propose a photography of the wood waste sector (productions, trades, consumptions), and then to elaborate different prospective scenarios on the use of wood waste volumes while taking into account possible evolutions on the medium or short term of the regulation and market of the wood/wood energy sector. The considered wastes come from industrial production, from the use of wood-based products, and from the end of life of products potentially containing wood. The authors present bibliographical sources and the adopted methodology, briefly describe the 'wood waste' system with its actors, and then report their assessment of wood wastes. They propose a global assessment as well as detailed assessments with respect to waste origins: wood trade and distribution, industries, craft, households and communities, building sector, public and private tertiary sector, packaging. They also address the collection and management of wood wastes by public services, and present the different types of valorisation (panel fabrication, energy, and others). They discuss exports, and then present different scenarios: a trend-based scenario, and two prospective scenarios with a priority to energetic valorisation or to material valorisation of wood wastes. These scenarios are compared

Formation of metal agglomerates during carbonisation of chromated copper arsenate (CCA) treated wood waste: Comparison between a lab scale and an industrial plant

Energy Technology Data Exchange (ETDEWEB)

Helsen, Lieve [Katholieke Universiteit Leuven, Department of Mechanical Engineering, Division of Applied Mechanics and Energy Conversion, Celestijnenlaan 300A, B-3001 Leuven (Heverlee) (Belgium)]. E-mail: lieve.helsen@mech.kuleuven.be; Hacala, Amelie [Company Thermya, 1 rue Nicolas Appert, 33140 Villenave d' Ornon (France)]. E-mail: hacala@thermya.com

2006-10-11

This paper compares the results obtained by scanning electron microscopy coupled to X-ray analysis (SEM-EDXA) of the solid product after carbonisation of treated wood waste in a lab scale and in an industrial installation. These setups (lab scale and industrial) are characterized by different operating conditions of the carbonisation process. Moreover, the wood waste input to the processes differs significantly. From this study, it is clear that some similarities but also some differences exist between the lab scale study and the study with the industrial Chartherm plant. In both reactors, a metal (and mineral) agglomeration process takes place, even in the case of untreated wood. The agglomerates initially present in the wood input may serve as a seed for the metal agglomeration process during 'chartherisation'. The industrial setup leads to a broader range of agglomerates' size (0.1-50 {mu}m) and composition (all possible combinations of Cu, Cr, As and wood minerals). Some agglomerates contain the three metals but the major part is a combination of wood minerals and one or two of the three preservative metals, while all agglomerates analysed in the lab scale product contain the three metals. The separate influence of wood input characteristics and process conditions cannot be derived from these experiments, but the observations suggest that the higher the CCA retention in the wood input is, the easier is the metal agglomeration process during chartherisation of CCA treated wood waste. From the analyses performed in this study it seems that copper behaves differently in the sense that it agglomerates easily, but the resulting particles are small (<1 {mu}m)

Formation of metal agglomerates during carbonisation of chromated copper arsenate (CCA) treated wood waste: Comparison between a lab scale and an industrial plant

International Nuclear Information System (INIS)

Helsen, Lieve; Hacala, Amelie

2006-01-01

This paper compares the results obtained by scanning electron microscopy coupled to X-ray analysis (SEM-EDXA) of the solid product after carbonisation of treated wood waste in a lab scale and in an industrial installation. These setups (lab scale and industrial) are characterized by different operating conditions of the carbonisation process. Moreover, the wood waste input to the processes differs significantly. From this study, it is clear that some similarities but also some differences exist between the lab scale study and the study with the industrial Chartherm plant. In both reactors, a metal (and mineral) agglomeration process takes place, even in the case of untreated wood. The agglomerates initially present in the wood input may serve as a seed for the metal agglomeration process during 'chartherisation'. The industrial setup leads to a broader range of agglomerates' size (0.1-50 μm) and composition (all possible combinations of Cu, Cr, As and wood minerals). Some agglomerates contain the three metals but the major part is a combination of wood minerals and one or two of the three preservative metals, while all agglomerates analysed in the lab scale product contain the three metals. The separate influence of wood input characteristics and process conditions cannot be derived from these experiments, but the observations suggest that the higher the CCA retention in the wood input is, the easier is the metal agglomeration process during chartherisation of CCA treated wood waste. From the analyses performed in this study it seems that copper behaves differently in the sense that it agglomerates easily, but the resulting particles are small (<1 μm)

Swedish recovered wood waste: linking regulation and contamination.

Science.gov (United States)

Krook, J; Mårtensson, A; Eklund, M; Libiseller, C

2008-01-01

In Sweden, large amounts of wood waste are generated annually from construction and demolition activities, but also from other discarded products such as packaging and furniture. A large share of this waste is today recovered and used for heat production. However, previous research has found that recovered wood waste (RWW) contains hazardous substances, which has significant implications for the environmental performance of recycling. Improved sorting is often suggested as a proper strategy to decrease such implications. In this study, we aim to analyse the impacts of waste regulation on the contamination of RWW. The occurrence of industrial preservative-treated wood, which contains several hazardous substances, was used as an indicator for contamination. First the management of RWW during 1995-2004 was studied through interviews with involved actors. We then determined the occurrence of industrial preservative-treated wood in RWW for that time period for each supplier (actor). From the results, it can be concluded that a substantially less contaminated RWW today relies on extensive source separation. The good news is that some actors, despite several obstacles for such upstream efforts, have already today proved capable of achieving relatively efficient separation. In most cases, however, the existing waste regulation has not succeeded in establishing strong enough incentives for less contaminated waste in general, nor for extensive source separation in particular. One important factor for this outcome is that the current market forces encourage involved actors to practice weak quality requirements and to rely on end-of-pipe solutions, rather than put pressure for improvements on upstream actors. Another important reason is that there is a lack of communication and oversight of existing waste regulations. Without such steering mechanisms, the inherent pressure from regulations becomes neutralized.

Online sorting of recovered wood waste by automated XRF-technology: part II. Sorting efficiencies.

Science.gov (United States)

Hasan, A Rasem; Solo-Gabriele, Helena; Townsend, Timothy

2011-04-01

Sorting of waste wood is an important process practiced at recycling facilities in order to detect and divert contaminants from recycled wood products. Contaminants of concern include arsenic, chromium and copper found in chemically preserved wood. The objective of this research was to evaluate the sorting efficiencies of both treated and untreated parts of the wood waste stream, and metal (As, Cr and Cu) mass recoveries by the use of automated X-ray fluorescence (XRF) systems. A full-scale system was used for experimentation. This unit consisted of an XRF-detection chamber mounted on the top of a conveyor and a pneumatic slide-way diverter which sorted wood into presumed treated and presumed untreated piles. A randomized block design was used to evaluate the operational conveyance parameters of the system, including wood feed rate and conveyor belt speed. Results indicated that online sorting efficiencies of waste wood by XRF technology were high based on number and weight of pieces (70-87% and 75-92% for treated wood and 66-97% and 68-96% for untreated wood, respectively). These sorting efficiencies achieved mass recovery for metals of 81-99% for As, 75-95% for Cu and 82-99% of Cr. The incorrect sorting of wood was attributed almost equally to deficiencies in the detection and conveyance/diversion systems. Even with its deficiencies, the system was capable of producing a recyclable portion that met residential soil quality levels established for Florida, for an infeed that contained 5% of treated wood. Copyright © 2010 Elsevier Ltd. All rights reserved.

Comparative study on liquefaction of creosote and chromated copper arsenate (CCA)-treated wood and untreated southern pine wood: effects of acid catalyst content, liquefaction time, temperature, and phenol to wood ratio

Science.gov (United States)

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Creosote- and chromated copper arsenate (CCA)-treated wood waste and untreated southern pine wood were liquefied with phenol and sulfuric acid. The effects of sulfuric acid content, liquefaction time, liquefaction temperature, and phenol to wood ratio on liquefaction rate (i.e., wood residue content) were investigated and analyzed by analysis of variance (...

Power generation from waste wood

Energy Technology Data Exchange (ETDEWEB)

Nitsche, H

1980-04-18

Since the energy crisis, power generation from waste wood has become increasingly important. The most profitable way to use waste wood in woodworking plants with an annual production of 100 to 150,000 m/sup 3/ solid measure of wood chips and bark is by combustion and thermal energy recovery. In plants with an annual production of 10,000 m/sup 3/ solid measure of wood chips and bark, electric power generation is a suitable application.

Quantities of arsenic-treated wood in demolition debris generated by Hurricane Katrina.

Science.gov (United States)

Dubey, Brajesh; Solo-Gabriele, Helena M; Townsendt, Timothy G

2007-03-01

The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood.

Waste-wood resource supply assessment. Final report

International Nuclear Information System (INIS)

1991-08-01

The report documents and analyzes the availability and supply of wood waste in New York State to determine the type and amount currently generated to estimate its potential future use as a fuel. Detailed, current information is included on the availability, quantity and price of wood waste. Topics include wood waste markets; the harvesting and supply infrastructure; current and project prices; competing markets; environmental impacts of harvesting, processing and burning wood waste for fuel; and factors affecting long-term availability and supply. New York State's waste wood resource was evaluated to complete the Energy Authority's recent investigation of the potential role of wood in producing electric power. In 1989 approximately 11.8 million tons of wood waste were generated in New York State. More than 8 million tons or 68 percent, were disposed of by municipal solid waste and construction and demolition debris facilities. Just under 3.8 million tons or 32 percent, were reused and/or recycled. More than 25.7 million tons of wood waste could be available annually for fuel. Of the amount, more than 17.2 million tons per year, or 67 percent, could be produced by silvicultural activities that improve the health and productivity of forests

The use of wood waste for energy production

International Nuclear Information System (INIS)

Karlopoulos, E.; Pavloudakis, F.

1999-01-01

The paper presents some technical aspects and management issues of wood waste reuse end disposal. It refers to the Greek and European legislation which determines the framework for rational and environmental friendly practices for woos waste management. It refers also to the wood waste classification systems and the currently applied methods of wood waste disposal and reuse. Emphasis is given to the wood waste-to-energy conversion system, particularly to the pretreatment requirements, the combustion techniques, and the environmental constrains. Finally, the decision making process for the investments in the wood waste firing thermal units is discussed

Influence of corn steep liquor and glucose on colonization of control and CCB (Cu/Cr/B)-treated wood by brown rot fungi

International Nuclear Information System (INIS)

Humar, Miha; Amartey, Sam A.; Pohleven, Franc

2006-01-01

There are increasing problems with regard to the disposal of treated wood waste. Due to heavy metals or arsenic in impregnated wood waste, burning and landfill disposal options are not considered to be environmentally friendly solutions for dealing with this problem. Extraction of the heavy metals and recycling of the preservatives from the wood waste is a much more promising and environmentally friendly solution. In order to study the scale up of this process, copper/chromium/boron-treated wood specimens were exposed to copper tolerant (Antrodia vaillantii and Leucogyrophana pinastri) and copper sensitive wood decay fungi (Gloeophyllum trabeum and Poria monticola). Afterwards, the ability of fungal hyphae to penetrate and overgrow the wood specimens was investigated. The fungal growths were stimulated by immersing the specimens into aqueous solution of glucose or corn steep liquor prior to exposure to the fungi. The fastest colonization of the impregnated wood was by the copper tolerant A. vaillantii. Addition of glucose onto the surface of the wood specimens increased the fungi colonization of the specimens; however, immersion of the specimens into the solution of corn steep liquor did not have the same positive influence. These results are important in elucidating copper toxicity in wood decay fungi and for using these fungi for bioremediation of treated wood wastes

Wood waste: A disposal problem or an opportunity?

International Nuclear Information System (INIS)

Vajda, P.

1989-01-01

The utilization of wood wastes in North America is reviewed, with a focus on the wood products industry and markets. On the whole, wood mill residues in North America have always been utilized except for a period from the 1940s to the 1970s oil crisis. In the latter period, low cost electric power and hydrocarbon fuels rendered uneconomical the use of wood wastes as fuel. As a response to the problem of disposing these wastes, a number of innovations occurred in that period, including the use of wood chips for manufacturing pulp and particleboard, and the use of sawdust and shavings for manufacturing hardboard and medium density fiberboard. Uses for bark, except as fuel, have not been successfully developed. Since the 1970s, wood waste in the USA is essentially all used for composite board products and fuel. This is also true in eastern Canada, which is close to the wood products markets and which has fairly high oil and gas costs. However, in western Canada, low energy costs and small internal markets have led to a serious wood waste disposal problem. A survey of wood waste supply and demand shows large surpluses in mill residues in western Canada and some remote locations in northern Ontario and Quebec. The Pacific Rim countries are identified as a potential market for western Canadian composite board production. The use of other sources of wood waste (forestry or logging residues, which are costly to collect, and municipal construction waste) is briefly discussed

An assessment of management practices of wood and wood-related wastes in the urban environment

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

Forest biomass and wood waste resources

Science.gov (United States)

K. Skog; P. Lebow; D.. Dykstra; P.. Miles; B.J. Stokes; R.D. Perlack; M. Buford; J. Barbour; D. McKeever

2011-01-01

This chapter provides estimates of forest biomass and wood waste quantities, as well as roadside costs (i.e., supply curves) for each county in the contiguous United States. Roadside price is the price a buyer pays for wood chips at a roadside in the forest, at a processing mill location in the case of mill residue, or at a landfill for urban wood wastes prior to any...

Application of near-infrared spectroscopy to preservative-treated wood

Science.gov (United States)

Chi-Leung So; Stan T. Lebow; Thomas L. Eberhardt; Leslie H. Groom; Todd F. Shupe

2009-01-01

Near infrared (NIR) spectroscopy is now a widely-used technique in the field of forest products, especially for physical and mechanical property determinations. This technique is also ideal for the chemical analysis of wood. There has been a growing need to find a rapid, inexpensive and reliable method to distinguish between preservative-treated and untreated waste...

Leaching of chromated copper arsenate (CCA)-treated wood in a simulated monofill and its potential impacts to landfill leachate

Energy Technology Data Exchange (ETDEWEB)

Jambeck, Jenna R. [Department of Environmental Engineering Sciences, University of Florida, Gainesville, FL 32611-6450 (United States); Townsend, Timothy [Department of Environmental Engineering Sciences, University of Florida, Gainesville, FL 32611-6450 (United States)]. E-mail: ttown@ufl.edu; Solo-Gabriele, Helena [Department of Civil, Architectural, and Environmental Engineering, University of Miami, Coral Gables, FL 33146-0630 (United States)

2006-07-31

The proper end-of-life management of chromated copper arsenate (CCA)-treated wood, which contains arsenic, copper, and chromium, is a concern to the solid waste management community. Landfills are often the final repository of this waste stream, and the impacts of CCA preservative metals on leachate quality are not well understood. Monofills are a type of landfill designed and operated to dispose a single waste type, such as ash, tires, mining waste, or wood. The feasibility of managing CCA-treated wood in monofills was examined using a simulated landfill (a leaching lysimeter) that contained a mix of new and weathered CCA-treated wood. The liquid to solid ratio (LS) reached in the experiment was 0.63:1. Arsenic, chromium, and copper leached from the lysimeter at average concentrations of 42 mg/L for arsenic, 9.4 mg/L for chromium, and 2.4 mg/L for copper. Complementary batch leaching studies using deionized water were performed on similar CCA-treated wood samples at LS of 5:1 and 10:1. When results from the lysimeter were compared to the batch test results, copper and chromium leachability appeared to be reduced in the lysimeter disposal environment. Of the three metals, arsenic leached to the greatest extent and was found to have the best correlation between the batch and the lysimeter experiments.

Combustion of Waste Wood. Second phase of the collaboration project on waste wood combustion

International Nuclear Information System (INIS)

Andersson, Annika; Andersson, Christer; Eriksson, Jan; Hemstroem, Bengt; Jungstedt, Jenny; Kling, Aasa; Bahr, Bo von; Ekvall, Annika; Eskilsson, David; Tullin, Claes; Harnevie, Henrik; Sieurin, Jan; Keihaes, Juha; Mueller, Christian; Berg, Magnus; Wikman, Karin

2003-08-01

Combustion of waste wood has during the last decade increased dramatically and this has resulted in a number of Swedish plants using this fuel, e.g. Handeloe P11 (Norrkoeping) and ldbaecken P3 (Nykoeping), and yet other plants that are under construction (e.g. Nynaeshamn). The experience from these plants are that waste wood combustion results in a number of operational problems. To some extent these problems are different compared with the problems related to combustion of other biofuels but the situation is not directly comparable to waste incinerators. The problems are mainly related to slagging and fouling of heat exchanger surfaces and accelerated corrosion at relatively low temperature compared to the situation for ordinary biofuels. In some cases an increase in the emissions of specific substances can also result in difficulties to fulfil the EC-directive on waste combustion. Within previous projects the main problems related to combustion of waste wood have been identified and to some extent the cause of these problems has been clarified. One result of this reported investigation is a deeper understanding of the actual causes of these problems. However, the most important result is a number of recommendations for different measures on how to achieve disturbance-free combustion of waste wood. These recommendations actually summarises the most important possible solutions on how to achieve a disturbance-free operation and a lower maintenance cost for boilers combusting waste wood and can thereby be regarded as a short summery of the whole project: 1) Improving fuel quality by Improved sorting at the source and Sieving of the fuel -> Reducing the amount of metals and chlorine and Separation of fines and thereby reducing the amount of metals. 2) Combustion modifications by Avoiding reducing conditions at the heat exchanger surfaces -> Minimising slagging, fouling and corrosion. 3) Additives or co-combustion by Addition of sulphur with the fuel; Injection of

USE OF CANDEIA’S (Eremanthus erythropappus WASTE WOOD

Directory of Open Access Journals (Sweden)

Rosimeire Cavalcante dos Santos

2008-09-01

Full Text Available The candeia (Eremanthus erythropappus is a native forest species with multiple uses and specially utilized as essential oils source. The use of the candeia´s waste wood after oil extraction for particle panels production becomes a viable alternative, avoiding environmental problems and increasing the availability of these products in the consuming market. This work verified the viability of producing wood-cement panels using waste wood generated after the extraction of candeia’s oil, in association with pinus and eucalipto woods. The experiment was installed according to a completely randomized design with three repetitions. The treatments were arranged according to a factorial 2 x 3 scheme (two wooden species and three replacement percentages of the woods by candeia’s waste. The results of the physical and mechanical property tests showed high potentiality of candeia waste wood, after oil extraction, in association with pinus and eucalipto wood for manufacturing wood-cement panels.

Furniture wood wastes: Experimental property characterisation and burning tests

International Nuclear Information System (INIS)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna; Pretelli, Silvia; Tombari, Lucia; Mangani, Filippo

2009-01-01

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg -1 for HHV, and from 3304 to 4634 kcal kg -1 for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM 1 fraction during incomplete industrial wood burning.

The use of urban wood waste as an energy resource

Science.gov (United States)

Khudyakova, G. I.; Danilova, D. A.; Khasanov, R. R.

2017-06-01

The capabilities use of wood waste in the Ekaterinburg city, generated during the felling of trees and sanitation in the care of green plantations in the streets, parks, squares, forest parks was investigated in this study. In the cities at the moment, all the wood, that is removed from city streets turns into waste completely. Wood waste is brought to the landfill of solid household waste, and moreover sorting and evaluation of the quantitative composition of wood waste is not carried out. Several technical solutions that are used in different countries have been proposed for the energy use of wood waste: heat and electrical energy generation, liquid and solid biofuel production. An estimation of the energy potential of the city wood waste was made, for total and for produced heat and electrical energy based on modern engineering developments. According to our estimates total energy potential of wood waste in the city measure up more 340 thousand GJ per year.

Pretreatment Characteristics of Waste Oak Wood by Ammonia Percolation

Science.gov (United States)

Kim, Jun-Seok; Kim, Hyunjoon; Lee, Jin-Suk; Lee, Joon-Pyo; Park, Soon-Chul

A log of waste oak wood collected from a Korean mushroom farm has been tested for ammonia percolation pretreatment. The waste log has different physical characteristics from that of virgin oak wood. The density of the waste wood was 30% lower than that of virgin oak wood. However, there is little difference in the chemical compositions between the woods. Due to the difference in physical characteristics, the optimal pretreatment conditions were also quite different. While for waste oak the optimum temperature was determined to be 130°C, for virgin oak wood the optimum pretreatment was only achieved at 170°C. Presoaking for 12 h with ammonia solution before pretreatment was helpful to increase the delignification efficiency.

Kraft pulping of industrial wood waste

Science.gov (United States)

Aziz. Ahmed; Masood. Akhtar; Gary C. Myers; Gary M. Scott

1998-01-01

Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

Scarcity on the market for wood wastes

International Nuclear Information System (INIS)

De Boer, A.

2004-01-01

An overview is given of the market for wood wastes in the Netherlands and how this affects the targets to use biomass. Several types of biomass must be imported, not only wood wastes, but also e.g. olive stones and cacao shells [nl

Characterization and potential recycling of home building wood waste

Science.gov (United States)

Philip A. Araman; D.P. Hindman; M.F. Winn

2010-01-01

Construction waste represents a significant portion of landfill waste, estimated as 17% of the total waste stream. Wood construction waste of a 2000 square foot single family home we found to be 1500-3700 lbs of solid-sawn wood, and 1000-1800 lbs of engineered wood products (EWP). Much of the solid-sawn lumber and EWPs could be recycled into several products. Through a...

Arsenic, chromium, and copper leaching from CCA-treated wood and their potential impacts on landfill leachate in a tropical country.

Science.gov (United States)

Kamchanawong, S; Veerakajohnsak, C

2010-04-01

This study looks into the potential risks of arsenic, chromium, and copper leaching from disposed hardwoods treated with chromated copper arsenate (CCA) in a tropical climate. The Toxicity Characteristic Leaching Procedure (TCLP) and the Waste Extraction Test (WET) were employed to examine new CCA-treated Burseraceae and Keruing woods, weathered CCA-treated teak wood, and ash from new CCA-treated Burseraceae wood. In addition, a total of six lysimeters, measuring 2 m high and 203 mm in diameter were prepared to compare the leachate generated from the wood monofills, construction and demolition (C&D) debris landfills and municipal solid waste (MSW) landfills, containing CCA-treated Burseraceae wood. The TCLP and WET results showed that the CCA-treated Burseraceae wood leached higher metal concentrations (i.e. 9.19-17.70 mg/L, 1.14-5.89 mg/L and 4.83-23.89 mg/L for arsenic, chromium, and copper, respectively) than the CCA-treated Keruing wood (i.e. 1.74-11.34 mg/L, 0.26-3.57 mg/L and 0.82-13.64 mg/L for arsenic, chromium and copper, respectively). Ash from the CCA-treated Burseraceae wood leached significantly higher metal concentrations (i.e. 108.5-116.9 mg/L, 1522-3862 mg/L and 84.03-114.4 mg/L for arsenic, chromium and copper, respectively), making this type of ash of high concern. The lysimeter study results showed that the MSW lysimeter exhibited higher reducing conditions, more biological activities and more dissolved ions in their leachates than the wood monofill and C&D debris lysimeters. All leachates generated from the lysimeters containing the CCA-treated Burseraceae wood contained significantly higher concentrations of arsenic in comparison to those of the untreated wood: in the range of 0.53-15.7 mg/L. It can be concluded that the disposal of CCA-treated Burseraceae wood in an unlined C&D landfill or a MSW landfill has the potential to contaminate groundwater.

Nigerian Wood Waste: A Potential Resource for Economic ...

African Journals Online (AJOL)

ADOWIE PERE

methods these vast amount of wood residues are often discarded ... contradict sustainable solid waste management which entails various .... waste through the production of steam in boiler super-heater .... Wood Fuels Handbook. AIEL: Italian.

Extant contents of chromium, copper and arsenic in waste CCA-treated timber

International Nuclear Information System (INIS)

Chiba, Keiko; Uchida, Shinpei; Honma, Yoshinori; Sera, Koichiro; Saitoh, Katsumi

2009-01-01

The segregation and disposal of chromated copper arsenate (CCA)-treated wood waste when recycling building waste materials is a serious issue. We examined the contents of CCA preserved cedar timber by PIXE analysis. CCA preserved timber contained large amounts of these metals both on the surface and core of the wood. The ratio of chromium, copper and arsenic contained on the surface was 1:2:1, and in contrast, the ratio in the core was 1:1:2. In other words, the arsenic content was highest in the core. Moreover, the chemical form of arsenic in both parts of the wood was only inorganic arsenic; the same form of arsenic in preservative components known as carcinogenic substances. These findings mean that the complete separation of waste CCA preserved timber from construction and demolition wood is needed. (author)

Waste wood incineration: long-lasting, environment-friendly and CO2-neutral

International Nuclear Information System (INIS)

Bouma, J.W.J.

1993-01-01

The economic aspects of energy production from waste wood are evaluated. Heating systems based on the incineration of wood have been considerably improved recently. Several aspects of the incineration of waste wood are reviewed: the implications with regard to the greenhouse effect, the calorific value of wood, the incineration process, and the cost price calculation of energy production by waste wood incineration. In conclusion is stated that energy production by waste wood incineration is a valuable economic alternative for heat production by oil products, especially in view of the current anti-pollution taxes in Belgium. (A.S.)

Demonstration of the efficiency and robustness of an acid leaching process to remove metals from various CCA-treated wood samples.

Science.gov (United States)

Coudert, Lucie; Blais, Jean-François; Mercier, Guy; Cooper, Paul; Janin, Amélie; Gastonguay, Louis

2014-01-01

In recent years, an efficient and economically attractive leaching process has been developed to remove metals from copper-based treated wood wastes. This study explored the applicability of this leaching process using chromated copper arsenate (CCA) treated wood samples with different initial metal loading and elapsed time between wood preservation treatment and remediation. The sulfuric acid leaching process resulted in the solubilization of more than 87% of the As, 70% of the Cr, and 76% of the Cu from CCA-chips and in the solubilization of more than 96% of the As, 78% of the Cr and 91% of the Cu from CCA-sawdust. The results showed that the performance of this leaching process might be influenced by the initial metal loading of the treated wood wastes and the elapsed time between preservation treatment and remediation. The effluents generated during the leaching steps were treated by precipitation-coagulation to satisfy the regulations for effluent discharge in municipal sewers. Precipitation using ferric chloride and sodium hydroxide was highly efficient, removing more than 99% of the As, Cr, and Cu. It appears that this leaching process can be successfully applied to remove metals from different CCA-treated wood samples and then from the effluents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Coal and wood fuel for electricity production: An environmentally sound solution for waste and demolition wood

Energy Technology Data Exchange (ETDEWEB)

Penninks, F.W.M. [EPON, Zwolle (Netherlands)

1997-12-31

Waste wood from primary wood processing and demolition presents both a problem and a potential. If disposed in landfills, it consumes large volumes and decays, producing CH{sub 4}, CO{sub 2} and other greenhouse gases. As an energy source used in a coal fired power plant it reduces the consumption of fossil fuels reducing the greenhouse effect significantly. Additional advantages are a reduction of the ash volume and the SO{sub 2} and NO{sub x} emissions. The waste wood requires collection, storage, processing and burning. This paper describes a unique project which is carried out in the Netherlands at EPON`s Gelderland Power Plant (635 MW{sub e}) where 60 000 tonnes of waste and demolition wood will be used annually. Special emphasis is given to the processing of the powdered wood fuel. Therefore, most waste and demolition wood can be converted from an environmental liability to an environmental and economic asset. (author)

Coal and wood fuel for electricity production: An environmentally sound solution for waste and demolition wood

Energy Technology Data Exchange (ETDEWEB)

Penninks, F W.M. [EPON, Zwolle (Netherlands)

1998-12-31

Waste wood from primary wood processing and demolition presents both a problem and a potential. If disposed in landfills, it consumes large volumes and decays, producing CH{sub 4}, CO{sub 2} and other greenhouse gases. As an energy source used in a coal fired power plant it reduces the consumption of fossil fuels reducing the greenhouse effect significantly. Additional advantages are a reduction of the ash volume and the SO{sub 2} and NO{sub x} emissions. The waste wood requires collection, storage, processing and burning. This paper describes a unique project which is carried out in the Netherlands at EPON`s Gelderland Power Plant (635 MW{sub e}) where 60 000 tonnes of waste and demolition wood will be used annually. Special emphasis is given to the processing of the powdered wood fuel. Therefore, most waste and demolition wood can be converted from an environmental liability to an environmental and economic asset. (author)

Sources of heavy metal contamination in Swedish wood waste used for combustion

International Nuclear Information System (INIS)

Krook, J.; Martensson, A.; Eklund, M.

2006-01-01

In this paper, wood waste (RWW) recovered for heat production in Sweden was studied. Previous research has concluded that RWW contains elevated amounts of heavy metals, causing environmental problems during waste management. This study extends previous work on RWW by analysing which pollution sources cause this contamination. Using existing data on the metal contents in various materials, and the amounts of these materials in RWW, the share of the elevated amounts of metals in RWW that these materials explain was quantified. Six different materials occurring in RWW were studied and the results show that they explain from 70% to 100% of the amounts of arsenic, chromium, lead, copper and zinc in RWW. The most important materials contributing to contamination of RWW are surface-treated wood, industrial preservative-treated wood, plastic and galvanised fastening systems. These findings enable the development and evaluation of strategies aiming to decrease pollution and resource loss from handling RWW. It is argued that source separation and measures taken further downstream from the generation site, such as treatment, need to be combined to substantially decrease the amount of heavy metals in RWW

PRESERVATIVE LEACHING FROM WEATHERED CCA-TREATED WOOD

Science.gov (United States)

Disposal of discarded CCA-treated wood in landfills raises concerns with respect to leaching of preservative compounds. When unweathered CCA-treated wood is leached using the toxicity characteristic leaching procedure (TCLP), arsenic concentrations exceed the toxicity characteris...

PROTECTIVE TREATMENT OF WOOD IMPREGNATING COMPOSITION OF PETROCHEMICAL WASTE

Directory of Open Access Journals (Sweden)

T. V. Maslakova

2015-01-01

Full Text Available The paper presents results of experimental and theoretical studies aimed at expanding the applications of the copolymers on the basis of the waste styrene production. One of the areas is used as impregnating compositions of wood materials, selection of optimal conditions modification on samples of the most widely used in the industry of wood, such as birch, aspen and other. Studies were conducted to obtain and use an impregnating compositions based on copolymers synthesized from waste products of styrene and the cubic remainder rectification of ethylbenzene (CRRE for the protective treatment of birch wood. Identified physic-chemical characteristics of physical mixtures of copolymers «CORS», «STAM», CRRE at different ratios. Studied the process of modification birch using the method of experiment planning greco-latin square of the fourth order, and the influence of such factors as the temperature of the impregnating composition, the duration of the impregnation, the temperature and duration of thermal treatment on the performance moisture resistance of wood. Were established optimal conditions modification birch wood treated impregnating compositions on the basis of physical mixtures of copolymer «CORS» with CRRE and copolymer «STAM» with CRRE is the mixing ratio 2:1, the duration and temperature of the impregnation 7 h and 95 0C, time and temperature of heat treatment 7 h and 170 0C, respectively. A sealing composition containing CRRE with copolymer «STAM» 1:2 is more preferable, as in the structure of the copolymer «STAM» contains carboxyl and anhydrite group. Thus was justified use for the modification of natural wood impregnating compositions on the basis of physical mixtures of CRRE with copolymers «CORS» and «STAM», which improve the properties of wood, increase moisture and weather resistance more than twice.

Chemi-thermomechanical pulping of para rubber waste wood

Energy Technology Data Exchange (ETDEWEB)

Kubo, T.; Hosokawa, J.; Kobayashi, T.; Kobayashi, Y.

1981-01-01

The addition of NaOH to Na/sub 2/SO/sub 3/-treated waste wood chips (Hevea brasiliensis) increased long fiber fraction, Klason lignin content and bulk density, improved breaking length and tear factor, and decreased energy consumption in refining and brightness of resulting chemithermomechanical pulp. Lowering in brightness by alkali treatment was recovered by H/sub 2/O/sub 2/ bleaching, and bleaching with 8% H/sub 2/O/sub 2/ on pulp gave pulp with 61.3% brightness.

Waste-wood-derived fillers for plastics

Science.gov (United States)

Brent English; Craig M. Clemons; Nicole Stark; James P. Schneider

1996-01-01

Filled thermoplastic composites are stiffer, stronger, and more dimensionally stable than their unfilled counterparts. Such thermoplastics are usually provided to the end-user as a precompounded, pelletized feedstock. Typical reinforcing fillers are inorganic materials like talc or fiberglass, but materials derived from waste wood, such as wood flour and recycled paper...

Consideration of the energetic use of waste wood versus re-use of materials

International Nuclear Information System (INIS)

Bergsma, G.C.; Sas, H.

1997-01-01

Recycling of wood wastes to chipboard is compared with the combustion of waste wood in combination with high-efficient energy recovery. Both options show much better environmental effects than the disposal of wood wastes. The differences between the environmental effects of the first two options can be neglected. The reprocessing of wood wastes to chipboard results in a decrease of the production of gypsum board. That benefit is equal to the benefit of cocombustion of wood wastes in a coal-fired power plant, i.e. saving coal. 18 refs

Surface properties of thermally treated composite wood panels

Science.gov (United States)

Croitoru, Catalin; Spirchez, Cosmin; Lunguleasa, Aurel; Cristea, Daniel; Roata, Ionut Claudiu; Pop, Mihai Alin; Bedo, Tibor; Stanciu, Elena Manuela; Pascu, Alexandru

2018-04-01

Composite finger-jointed spruce and oak wood panels have been thermally treated under standard pressure and oxygen content conditions at two different temperatures, 180 °C and respectively 200 °C for short time periods (3 and 5 h). Due to the thermally-aided chemical restructuration of the wood components, a decrease in water uptake and volumetric swelling values with up to 45% for spruce and 35% for oak have been registered, comparing to the reference samples. In relation to water resistance, a 15% increase of the dispersive component of the surface energy has been registered for the thermal-treated spruce panels, which impedes water spreading on the surface. The thermal-treated wood presents superior resistance to accelerated UV exposure and subsequently, with up to 10% higher Brinell hardness values than reference wood. The proposed thermal treatment improves the durability of the finger-jointed wood through a more economically and environmental friendly method than traditional impregnation, with minimal degradative impact on the structural components of wood.

CFD modeling and experience of waste-to-energy plant burning waste wood

DEFF Research Database (Denmark)

Rajh, B.; Yin, Chungen; Samec, N.

2013-01-01

Computational Fluid Dynamics (CFD) is being increasingly used in industry for in-depth understanding of the fundamental mixing, combustion, heat transfer and pollutant formation in combustion processes and for design and optimization of Waste-to-Energy (WtE) plants. In this paper, CFD modeling...... the conversion of the waste wood in the fuel bed on the grate, which provides the appropriate inlet boundary condition for the freeboard 3D CFD simulation. The CFD analysis reveals the detailed mixing and combustion characteristics in the waste wood-fired furnace, pinpointing how to improve the design...

Corrosion of Fasteners in Wood Treated with Newer Wood Preservatives

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

This document compiles recent research findings related to corrosion of metals in preservative treated wood into a single report on corrosion of metals in wood. The research was conducted as part of the Research, Technology and Education portion of the National Historic Covered Bridge Preservation (NHCBP) Program administered by the Federal Highway Administration. The...

Factors affecting sodium hypochlorite extraction of CCA from treated wood.

Science.gov (United States)

Gezer, E D; Cooper, P A

2009-12-01

Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 degrees C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.

Wood waste in Europe

Energy Technology Data Exchange (ETDEWEB)

Matos, O; Ribeiro, R [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

1998-12-31

The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

Wood waste in Europe

Energy Technology Data Exchange (ETDEWEB)

Matos, O.; Ribeiro, R. [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

1997-12-31

The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

Wood products in the waste stream: Characterization and combustion emissions. Volume 1. Final report

International Nuclear Information System (INIS)

1992-11-01

Waste wood is wood separated from the solid-waste stream and processed into a uniform-sized product that is reused for other purposes such as fuel. As an alternative to the combustion of fossil fuels, it has raised concerns that if it is 'contaminated' with paints, resins, preservatives, etc., unacceptable environmental impacts may be generated during combustion. Given the difficulty of separating contaminated materials from waste wood and the large energy potential existing in the resource, it is important to identify possible problems associated with contaminated waste wood combustion. The study describes research about technical, public policy, and regulatory issues that affect the processing and combustion of waste wood for fuel. The project's purpose was to provide environmental regulators, project developers, and others with data to make informed decisions on the use of waste wood materials as a combustion resource. Potential environmental problems and solutions were identified. A specific project result was the identification of combustion system operation parameters and air pollution control technologies that can minimize emissions of identified air and solid waste contaminants from combustion of wood waste

Finishability of CCA pressure-treated wood

Science.gov (United States)

Alan Ross; Richard Carlson; William Feist; Steven Bussjaeger

2000-01-01

Thus, a need arose for the development of surface finishes for CCA-treated wood that could address the special requirements of this substrate and provide protection against the ravages of water, sunlight, mildew, and other aspects of weathering and wear. Initially, this need was not addressed, most wood preserving companies had little expertise in surface finishes and...

Variability in evaluating environmental impacts of treated wood.

Science.gov (United States)

Stan T. Lebow; Paul Cooper; Patricia K. Lebow

2004-01-01

Preservative-treated wood contains components that may be toxic to non-target organisms if released into the environment in sufficient quantities. Numerous studies have been conducted to determine the rate of preservative release from treated wood and/or the extent of their subsequent accumulation in the environment. These studies have produced a wide range of results...

Modification of polypropylene with radiation-treated wood fiber

International Nuclear Information System (INIS)

Czvikovszky, T.; Tapolcai, I.

1983-01-01

The dispersed wood material is used not only as filler for thermosetting polymers but also as a new type of fibrous additive for thermoplastics e.g. polypropylene. Benefit of this additive (filler or reinforcement) is determined by the coupling between the wood and the synthetic resin. Fibrous, dispersed wood material was preirradiated in air, treated with vinyl monomer containing polyester resin and then mixed in polypropylene. Processability of such thermoplastic blends as well as reactivity of the mixed components were followed by measuring energy, absorbed during the kneading of the melt. The vinylmonomer vinylmonomer - polyester additive, activated at higher temperature by the radiation-formed peroxy groups on the wood fiber, results in good processability of the thermoplastic blend, and gives interesting mechanical properties. Calandering, extrusion, pressmoulding and mechanical testing demonstrated good workability and practical value of the polypropylene composite material containing radiation-treated wood fiber. (author)

Gasification of Wood and Non-wood Waste of Timber Production as Perspectives for Development of Bioenergy

Science.gov (United States)

Kislukhina, Irina A.; Rybakova, Olga G.

2018-03-01

The article deals with biomass gasification technology using the gasification plant running on wood chips and pellets, produced from essential oils waste (waste of coniferous boughs). During the study, the authors solved the process task of improving the quality of the product gas derived from non-wood waste of timber production (coniferous boughs) due to the extraction of essential oils and the subsequent thermal processing of spent coniferous boughs at a temperature of 250-300°C degrees without oxygen immediately before pelleting. The paper provides the improved biomass gasification process scheme including the grinding of coniferous boughs, essential oil distillation and thermal treatment of coniferous boughs waste and pelletizing.

Pollution-free combustion of waste wood in Swiss joineries

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

The exploitation of scrap wood for heat generation in the wood processing industry makes sense not only in the context of energy conservation but also on environmental grounds. Existing energy requirements can be provided by renewable energy sources, relieving the burden on the public waste disposal facility. The wood-fired heating plant for a joinery in Pratteln, Switzerland consumes 150 to 180 tonnes of waste wood per year, enabling approximately 80 tonnes of heating oil to be saved. The heat produced is used in a local scheme to heat the joinery and adjacent housing. A new fibrous filter system for the retention of fine particles was installed, enabling the particle concentration in the exhaust to be reduced from 292 mg/m{sup 3} to 24 mg/m{sup 3}. (UK)

Corrosão de parafusos fixados à madeira tratada com soluções de creosoto vegetal Corrosion of screws fixed into wood treated with wood tar creosote solutions

Directory of Open Access Journals (Sweden)

Juarez Benigno Paes

2002-05-01

Full Text Available O objetivo desta pesquisa foi avaliar a corrosão de parafusos auto-rosqueáveis fixados à madeira tratada com soluções preservativas preparadas com creosoto vegetal, em condições de campo. Obteve-se o creosoto vegetal bruto por meio da destilação à temperatura de 110 - 255ºC do alcatrão vegetal. Uma fração dos destilados foi lavada com solução a 9% de bicarbonato de sódio, obtendo-se o creosoto vegetal purificado. Ambas as frações foram enriquecidas com 3% de naftenato de cobre; 3% de naftenato de zinco; 3% naftenato de cobalto; 2% de TBTO; 2% de tribromofenato de tubutil-estanho; 2% de pentaclorofenol; ou 0,4% de trióxido de arsênico. Foram preparadas 16 soluções, sendo 14 enriquecidas, além do creosoto vegetal bruto e do creosoto vegetal purificado. Estacas confeccionadas com madeira de alburno de Eucalyptus grandis foram tratadas pelo processo de célula- cheia (processo Bethell. Após o tratamento, parafusos auto-rosquéaveis de ferro zincado foram fixados às estacas. O ensaio foi instalado em três localidades da Zona da Mata de Minas Gerais (Viçosa, Ponte Nova e Leopoldina. A corrosividade das soluções de creosoto vegetal foi comparada à causada pelo creosoto mineral. As soluções preparadas com creosoto vegetal purificado foram menos corrosivas que suas similares preparadas com creosoto vegetal bruto, assemelhando-se ao creosoto mineral.The objective of this research was to evaluate the corrosion of screws fixed into wood treated with preservative solutions of wood tar creosote. The crude wood tar creosote was obtained through distillation of wood tar at 110 - 255ºC. A fraction of this product was washed with a solution of sodium bicarbonate at 9%, resulting in purified wood tar creosote. Both fractions were enriched with 3% of copper naphtenate, 3% of zinc naphtenate, 3% of cobalt naphtenate, 2% of TBTO, 2% of tributhyl-tin tribromophenate, 2% of pentachlorophenol, or with 0.4% of arsenic trioxide. A total

State-of-the-art of waste wood supply chain in Germany and selected European countries.

Science.gov (United States)

Garcia, Carlos A; Hora, Guido

2017-12-01

According to the statistic office of the European Union (Eurostat), Germany is the main producer of waste wood in Europe followed by France, United Kingdom, Italy and Finland. Based on the characteristics of the waste wood, it can be classified in four (4) categories: A I, A II, A III and A IV. This paper focuses in the A I waste wood since is the only category able to be used directly for both material and energy purposes without a previously pre-treatment. Currently, most of this waste wood is used for direct energy production due to the previous government legislation that promoted its use directly in incineration facilities. However, the newest Renewable Energy Act (EEG 2017) may promote the cascade-use of A I waste wood prior to be intended for energy purposes. Nonetheless, the government incentives to the energy sector is not the only bottleneck that the use of A I waste wood as raw material in the wood-based industry has to overcome. The peak availability, collection logistics (collection centers and transportation) and recycling facility location are some of the parameters that must be considered in order to design the "best" supply chain network for A I waste wood. This work presents a detailed description of the effect of the hierarchical strategic decision in the proper design of the waste wood supply chain. Additionally, the global picture of waste wood recycling in different European countries (UK, Italy and Finland) is briefly presented. Copyright © 2017. Published by Elsevier Ltd.

Microdistribution of copper-carbonate and iron oxide nanoparticles in treated wood

Energy Technology Data Exchange (ETDEWEB)

Matsunaga, Hiroshi, E-mail: mhiroshi@ffpri.affrc.go.jp; Kiguchi, Makoto [Forestry and Forest Products Research Institute (Japan); Evans, Philip D. [University of British Columbia, Centre for Advanced Wood Processing (Canada)

2009-07-15

Aqueous dispersions of copper-carbonate nanoparticles and microparticles have just begun to be exploited commercially for the preservative treatment of wood. The success of the new systems will depend, in part, on the uniform distribution of the preservative in wood and the ability of copper to penetrate cell walls. We examined the distribution of copper in wood treated with a nano-Cu preservative. Copper particles are not uniformly distributed in treated wood, but they accumulate in voids that act as the flow paths for liquids in wood. Particles are deposited on, but not within cell walls. Nevertheless, elemental copper is present within cell walls, but at a lower level than that in wood treated with a conventional wood preservative. These findings suggest that nano-Cu preservatives are able to deliver bioactive components into wood cell walls even though the majority of copper particles are too large to penetrate the cell wall's nanocapillary network.

The fungal composition of natural biofinishes on oil-treated wood

NARCIS (Netherlands)

van Nieuwenhuijzen, Elke J.; Houbraken, Jos A. M. P.; Punt, Peter J; Roeselers, Guus; Adan, Olaf C G; Samson, Robert A.

2017-01-01

Biofinished wood is considered to be a decorative and protective material for outdoor constructions, showing advantages compared to traditional treated wood in terms of sustainability and self-repair. Natural dark wood staining fungi are essential to biofinish formation on wood. Although all sorts

The fungal composition of natural biofinishes on oil-treated wood

NARCIS (Netherlands)

van Nieuwenhuijzen, E.J.; Houbraken, J.A.M.P.; Punt, P.J.; Roeselers, G.; Adan, O.C.G.; Samson, R.A.

2017-01-01

Background Biofinished wood is considered to be a decorative and protective material for outdoor constructions, showing advantages compared to traditional treated wood in terms of sustainability and self-repair. Natural dark wood staining fungi are essential to biofinish formation on wood. Although

Weathering methods for preservative treated wood and their applicability for fire retarded wood

NARCIS (Netherlands)

Voss, A.

1999-01-01

preservative treated wood. The aim of the presentation is to inform you about current testing methods and to discuss their applicability to test fire retarded wood in outdoor use. Assuming that fire retardants will only be used in out of ground contact, only those methods are mentioned, which fit

Waste to Energy : The Waste Incineration Directive and its Implementation in the Netherlands

NARCIS (Netherlands)

Duman, Murat; Boels, Luciaan

2007-01-01

Essent operates a coal-fired power plant, called AC-9, in Geertruidenberg. A gasifier connected to AC-9 thermally treats waste wood through gasification. The waste wood Essent used is demolition and construction wood, the so-called B-wood. The gas produced through gasification is fed into the

FIELD-SCALE LEACHING OF ARSENIC, CHROMIUM AND COPPER FROM WEATHERED TREATED WOOD

Science.gov (United States)

Hasan, A. Rasem; Hu, Ligang; Solo-Gabriele, Helena M.; Fieber, Lynne; Cai, Yong; Townsend, Timothy G.

2010-01-01

Earlier studies documented the loss of wood preservatives from new wood. The objective of this study was to evaluate losses from weathered treated wood under field conditions by collecting rainfall leachate from 5 different wood types, all with a surface area of 0.21 m2. Wood samples included weathered chromate copper arsenate (CCA) treated wood at low (2.7 kg/m3), medium (4.8 kg/m3) and high (35.4 kg/m3) retention levels, new alkaline copper quat (ACQ) treated wood (1.1 kg/m3 as CuO) and new untreated wood. Arsenic was found to leach at a higher rate (100 mg in 1 year for low retention) than chromium and copper (leached at the highest rate from the ACQ sample (670 mg). Overall results suggest that metals’ leaching is a continuous process driven by rainfall, and that the mechanism of release from the wood matrix changes as wood weathers. PMID:20053493

Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in Wood-Plastic Composites.

Science.gov (United States)

Sommerhuber, Philipp F; Welling, Johannes; Krause, Andreas

2015-12-01

The market share of Wood-Plastic Composites (WPC) is small but expected to grow sharply in Europe. This raises some concerns about suitable wood particles needed in the wood-based panels industry in Europe. Concerns are stimulated by the competition between the promotion of wooden products through the European Bioeconomy Strategy and wood as an energy carrier through the Renewable Energy Directive. Cascade use of resources and valorisation of waste are potential strategies to overcome resource scarcity. Under experimental design conditions, WPC made from post-consumer recycled wood and plastic (HDPE) were compared to WPC made from virgin resources. Wood content in the polymer matrix was raised in two steps from 0% to 30% and 60%. Mechanical and physical properties and colour differences were characterized. The feasibility of using cascaded resources for WPC is discussed. Results indicate the technical and economic feasibility of using recycled HDPE from packaging waste for WPC. Based on technical properties, 30% recycled wood content for WPC is feasible, but economic and political barriers of efficient cascading of biomass need to be overcome. Copyright © 2015 Elsevier Ltd. All rights reserved.

A new way of treating french radioactive waste

International Nuclear Information System (INIS)

Bernard Rottner; Fabrice Jannot; Lena Bergstroem

2006-01-01

STUDSVIK and ONECTRA have built a partnership in order to offer the French market new radwaste treatment services, by putting together their specific knowledge about radioactive waste treatment by combining and completing each other's specific knowledge. STUDSVIK provides services related to incineration, melting and recycling of waste originating from the nuclear industry and fuel fabrication plants. ONECTRA is a well known specialist about nuclear dismantling studies or operations driving, nuclear tools design, environmental engineering, chemical or radiological remediation, and nuclear project management. The goal of this partnership is to propose new solutions to treat radwaste, such as to: lower the global waste management price, Offer solutions for 'exotic' waste, provide recycling operations French nuclear Industry. The overall objectives with STUDSVIK's metal scrap treatment are to reduce the amount of waste having to be disposed of and to recycle valuable metals. The residual weight after treatment is normally between 2% and 7% of the incoming weight, depending on the activity content and combination of metals. Moreover, ONECTRA's specific developments for decontamination processes can lead to treat parts with higher levels of activity than what was done by STUDSVIK before. Experience from volume reduction has made it possible to develop a new approach for treatment of used steam generators. During the second half of 2005 this new method is used for treating a steam generator from a Swedish PWR. FREE RELEASE is a current operation in Europe, following the RP 89 European commission's recommendations, table 3-1. STUDSVIK is free-releasing metals since more than 15 years, with a long time partnership with the Steel Industry( ex: metallic waste from UK, Germany, Sweden, Switzerland, Belgium, a.s.o.). The waste owner gives an acceptance guarantee for return of secondary waste (like filter dust, material sorted out, slags, a.s.o), and ingots that can not be

Chemical yields from low-temperature pyrolysis of CCA-treated wood

Science.gov (United States)

Qirong Fu; Dimitris Argyropolous; Lucian Lucia; David Tilotta; Stan Lebow

2009-01-01

Low-temperature pyrolysis offers a feasible option for wood-waste management and the recovery of a variety of useful chemicals. The effect of chromated copper arsenate (CCA) wood preservative on the yield and composition of various pyrolysis products was investigated in the present research. A novel quantitative 31P nuclear magnetic resonance (...

Biocide leaching from CBA treated wood — A mechanistic interpretation

International Nuclear Information System (INIS)

Lupsea, Maria; Mathies, Helena; Schoknecht, Ute; Tiruta-Barna, Ligia; Schiopu, Nicoleta

2013-01-01

Treated wood is frequently used for construction. However, there is a need to ensure that biocides used for the treatment are not a threat for people or environment. The paper focused on Pinus sylvestris treated with copper–boron–azole (CBA), containing tebuconazole as organic biocide and monoethanolamine (Mea). This study investigates chemical mechanisms of fixation and mobilisation involved in the leaching process of the used inorganic and organic biocides in CBA. A pH dependent leaching test was performed, followed by a set of complementary analysis methods in order to identify and quantify the species released from wood. The main findings of this study are: -Organic compounds are released from untreated and treated wood; the quantity of released total organic carbon, carboxylic and phenolic functions increasing with the pH. -Nitrogen containing compounds, i.e. mainly Mea and its reaction products with extractives, are released in important quantities from CBA treated wood, especially at low pH. -The release of copper is the result of competitive reactions: fixation via complexation reactions and complexation with extractives in the liquid phase. The specific pH dependency of Cu leaching is explained by the competition of ligands for protonation and complexation. -Tebuconazole is released to a lesser extent relative to its initial content. Its fixation on solid wood structure seems to be influenced by pH, suggesting interactions with -OH groups on wood. Boron release appears to be pH independent and very high. This confirms its weak fixation on wood and also no or weak interaction with the extractives. - Highlights: ► A pH dependent leaching mechanism for CBA treated wood is described. ► The fixation and mobilisation of inorganic and organic biocides was investigated. ► Extractives' quantity and nature depend on pH. ► Competition of ligands for protonation and complexation explains Cu behaviour. ► Tebuconazole seems to interact with -OH groups on

Biocide leaching from CBA treated wood — A mechanistic interpretation

Energy Technology Data Exchange (ETDEWEB)

Lupsea, Maria [University of Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F-31077 Toulouse (France); INRA, UMR 792, F-31400 Toulouse (France); CNRS, UMR 5504, F-31400 Toulouse (France); Paris-Est University, CSTB — Scientific and Technical Centre for the Building Industry, ESE/Environment, 24 rue Joseph Fourier, F-38400 Saint Martin d' Hères (France); Mathies, Helena; Schoknecht, Ute [BAM — Federal Institute for Materials Research and Testing, Division 4.1, Unter den Eichen 87, 12205 Berlin (Germany); Tiruta-Barna, Ligia, E-mail: ligia.barna@insa-toulouse.fr [University of Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F-31077 Toulouse (France); INRA, UMR 792, F-31400 Toulouse (France); CNRS, UMR 5504, F-31400 Toulouse (France); Schiopu, Nicoleta [Paris-Est University, CSTB — Scientific and Technical Centre for the Building Industry, ESE/Environment, 24 rue Joseph Fourier, F-38400 Saint Martin d' Hères (France)

2013-02-01

Treated wood is frequently used for construction. However, there is a need to ensure that biocides used for the treatment are not a threat for people or environment. The paper focused on Pinus sylvestris treated with copper–boron–azole (CBA), containing tebuconazole as organic biocide and monoethanolamine (Mea). This study investigates chemical mechanisms of fixation and mobilisation involved in the leaching process of the used inorganic and organic biocides in CBA. A pH dependent leaching test was performed, followed by a set of complementary analysis methods in order to identify and quantify the species released from wood. The main findings of this study are: -Organic compounds are released from untreated and treated wood; the quantity of released total organic carbon, carboxylic and phenolic functions increasing with the pH. -Nitrogen containing compounds, i.e. mainly Mea and its reaction products with extractives, are released in important quantities from CBA treated wood, especially at low pH. -The release of copper is the result of competitive reactions: fixation via complexation reactions and complexation with extractives in the liquid phase. The specific pH dependency of Cu leaching is explained by the competition of ligands for protonation and complexation. -Tebuconazole is released to a lesser extent relative to its initial content. Its fixation on solid wood structure seems to be influenced by pH, suggesting interactions with -OH groups on wood. Boron release appears to be pH independent and very high. This confirms its weak fixation on wood and also no or weak interaction with the extractives. - Highlights: ► A pH dependent leaching mechanism for CBA treated wood is described. ► The fixation and mobilisation of inorganic and organic biocides was investigated. ► Extractives' quantity and nature depend on pH. ► Competition of ligands for protonation and complexation explains Cu behaviour. ► Tebuconazole seems to interact with -OH groups

Marine exposure of preservative-treated small wood panels

Science.gov (United States)

B. R. Johnson; D. I. Gutzmer

1984-01-01

Small wood panels treated with many different chemicals have been exposed to limnorian and teredine marine borers in the sea at Key West, Florida. These preservatives and treatments include creosotes with and without modification, waterborne salts, salt-creosote dual treatments, chemical modifications of wood, and modified polymers. In spite of the accelerated nature...

Modelling inorganic biocide emission from treated wood in water

Energy Technology Data Exchange (ETDEWEB)

Tiruta-Barna, Ligia, E-mail: Ligia.barna@insa-toulouse.fr [Universite de Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F-31077 Toulouse (France); INRA, UMR792, Laboratoire d' Ingenierie des Systemes Biologiques et des Procedes, F-31400 Toulouse (France); CNRS, UMR5504, F-31400 Toulouse (France); Schiopu, Nicoleta [Universite Paris-Est, CSTB- Scientific and Technical Centre for the Building Industry, ESE/Environment, 24, rue Joseph Fourier, 38400 Saint Martin d' Heres (France)

2011-09-15

Highlights: {center_dot} We developed a mechanistic model for biocide metals fixation/mobilisation in wood. {center_dot} This is the first chemical model explaining the biocide leaching from treated wood. {center_dot} The main fixation mechanism is the surface complexation with wood polymers. {center_dot} The biocide mobilization is due to metal-DOC complexation and pH effect. - Abstract: The objective of this work is to develop a chemical model for explaining the leaching behaviour of inorganic biocides from treated wood. The standard leaching test XP CEN/TS14429 was applied to a commercial construction material made of treated Pinus sylvestris (Copper Boron Azole preservative). The experimental results were used for developing a chemical model under PHREEQC (a geochemical software, with LLNL, MINTEQ data bases) by considering the released species detected in the eluates: main biocides Cu and B, other trace biocides (Cr and Zn), other elements like Ca, K, Cl, SO{sub 4}{sup -2}, dissolved organic matter (DOC). The model is based on chemical phenomena at liquid/solid interfaces (complexation, ion exchange and hydrolysis) and is satisfactory for the leaching behaviour representation. The simulation results confronted with the experiments confirmed the hypotheses of: (1) biocide fixation by surface complexation reactions with wood specific sites (carboxyl and phenol for Cu, Zn, Cr(III), aliphatic hydroxyl for B, ion exchange to a lesser extent) and (2) biocide mobilisation by extractives (DOC) coming from the wood. The maximum of Cu, Cr(III) and Zn fixation occurred at neutral pH (including the natural pH of wood), while B fixation was favoured at alkaline pH.

Aureobasidium melanogenum: a native of dark biofinishes on oil treated wood.

Science.gov (United States)

van Nieuwenhuijzen, Elke J; Houbraken, Jos A M P; Meijer, Martin; Adan, Olaf C G; Samson, Robert A

2016-05-01

The genus Aureobasidium, which is known as a wood staining mould, has been detected on oil treated woods in the specific stain formation called biofinish. This biofinish is used to develop a new protective, self-healing and decorative biotreatment for wood. In order to understand and control biofinish formation on oil treated wood, the occurrence of different Aureobasidium species on various wood surfaces was studied. Phenotypic variability within Aureobasidium strains presented limitations of morphological identification of Aureobasidium species. PCR amplification and Sanger sequencing of ITS and RPB2 were used to identify the culturable Aureobasidium species composition in mould stained wood surfaces with and without a biofinish. The analysed isolates showed that several Aureobasidium species were present and that Aureobasidium melanogenum was predominantly detected, regardless of the presence of a biofinish and the type of substrate. A. melanogenum was detected on wood samples exposed in the Netherlands, Cameroon, South Africa, Australia and Norway. ITS-specific PCR amplification, cloning and sequencing of DNA extracted from biofinish samples confirmed results of the culturing based method: A. melanogenum is predominant within the Aureobasidium population of biofinishes on pine sapwood treated with raw linseed oil and the outdoor placement in the Netherlands.

North American Wood Waste Forum: Summary of Group Feedback, 2-3, 2012

Science.gov (United States)

Bob Falk

2012-01-01

This report summarizes the feedback and recommendations of the North American Wood Recovery Group. This report summarizes the barriers and opportunities in wood recovery, reuse, and recycling as identified by this group of stakeholders from the wood industry, waste industry, and relevant government agencies.

Second-generation bioethanol from industrial wood waste of South American species

Directory of Open Access Journals (Sweden)

María E. Vallejos

2017-09-01

Full Text Available There is a global interest in replacing fossil fuels with renewable sources of energy. The present review evaluates the significance of South-American wood industrial wastes for bioethanol production. Four countries have been chosen for this review, i.e., Argentina, Brazil, Chile, and Uruguay, based on their current or potential forestry industry. It should be noted that although Brazil has a global bioethanol market share of 25%, its production is mainly first-generation bioethanol from sugarcane. The situation in the other countries is even worse, in spite of the fact that they have regulatory frameworks in place already allowing the substitution of a percentage of gasoline by ethanol. Pines and eucalyptus are the usually forested plants in these countries, and their industrial wastes, as chips and sawdust, could serve as promising raw materials to produce second-generation bioethanol in the context of a forest biorefinery. The process to convert woody biomass involves three stages: pretreatment, enzymatic saccharification, and fermentation. The operational conditions of the pretreatment method used are generally defined according to the physical and chemical characteristics of the raw materials and subsequently determine the characteristics of the treated substrates. This article also reviews and discusses the available pretreatment technologies for eucalyptus and pines applicable to South-American industrial wood wastes, their enzymatic hydrolysis yields, and the feasibility of implementing such processes in the mentioned countries in the frame of a biorefinery.

Technological and Thermal Properties of Thermoplastic Composites Filled with Heat-treated Alder Wood

Directory of Open Access Journals (Sweden)

Mürşit Tufan

2016-02-01

Full Text Available This study investigated the effect of heat-treated wood content on the water absorption, mechanical, and thermal properties of wood plastic composites (WPCs. The WPCs were produced from various loadings (30, 40, and 50 wt% of heat-treated and untreated alder wood flours (Alnus glutinosa L. using high-density polyethylene (HDPE with 3 wt% maleated polyethylene (MAPE coupling agent. All WPC formulations were compression molded into a hot press for 3 min at 170 ºC. The WPCs were evaluated using mechanical testing, Fourier transform infrared spectroscopy (FTIR, thermogravimetric analysis (TGA, and differential scanning calorimetry (DSC. The mechanical property values of the WPC specimens decreased with increasing amounts of the heat-treated wood flour, except for the tensile modulus values. The heat treatment of alder wood slightly increased the thermal stability of the WPCs compared with the reference WPCs. The crystallization degree (Xc and the enthalpy of crystallization of the WPCs slightly decreased with increasing content of the heat-treated wood flour. However, all WPCs containing the heat-treated alder wood flour showed a higher crystallinity degree than that of the virgin HDPE.

40 CFR 60.2971 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Science.gov (United States)

2010-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.2971 Section 60... Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.2971 What are the emission limitations for air curtain incinerators that burn only wood waste, clean lumber, and yard waste? (a) Within...

Carcinogenic risk of chromium, copper and arsenic in CCA-treated wood

International Nuclear Information System (INIS)

Ohgami, Nobutaka; Yamanoshita, Osamu; Thang, Nguyen Dinh; Yajima, Ichiro; Nakano, Chihiro; Wenting, Wu; Ohnuma, Shoko

2015-01-01

We showed that 2.1% of 233 pieces of lumber debris after the Great East Japan Earthquake was chromated copper arsenate (CCA)-treated wood. Since hexavalent chromium (Cr), copper (Cu) and pentavalent arsenic (As) in the debris may be diffused in the air via incineration, we exposed human lung normal (BEAS-2B) and carcinoma (A549) cells to Cr, Cu and As at the molar ratio in a representative CCA-treated wood. Co-exposure to 0.10 μM Cr and 0.06 μM As, which solely had no effect on colony formation, synergistically promoted colony formation in BEAS-2B cells, but not A549 cells, with activation of the PI3K/AKT pathway. Sole exposure and co-exposure to Cu showed limited effects. Since previous reports showed Cr and As concentrations to which human lungs might be exposed, our results suggest the importance to avoid diffusion of Cr and As in the air via incineration of debris including CCA-treated wood after the disaster. - Highlights: • CCA-treated wood was found in debris after the Great East Japan Earthquake in 2011. • Carcinogenic risk of CCA-treated woods was evaluated with human lung cell lines. • Co-exposure to Cr and As synergistically promoted colony formation. • Co-exposure to Cr and As synergistically activated the PI3/AKT pathway. • Effects of sole exposure and co-exposure to Cu on colony formation were limited. - Co-exposure to Cr and As, but not Cu, in CCA-treated wood debris from the Great East Japan Earthquake showed carcinogenicity in vitro.

Environmental impact of preservative-treated wood in a wetland boardwalk.

Science.gov (United States)

Stan T. Lebow; Patricia K. Lebow; Daniel O. Foster; Kenneth M. Brooks

Forest Service, Bureau of Land Management, and industry partners are cooperating in a study of the leaching and environmental effects of a wetland boardwalk. The construction project is considered bworst casec because the site has high rainfall and large volumes of treated wood were used. Separate boardwalk test sections were constructed using untreated wood or wood...

Classification of waste wood treated with chromated copper arsenate and boron/fluorine preservatives; Classificacao de residuos de madeira tratada com preservativos a base de arseniato de cobre cromatado e de boro/fluor

Energy Technology Data Exchange (ETDEWEB)

Ferrarini, Suzana Frighetto; Santos, Heldiane Souza dos; Miranda, Luciana Gampert; Azevedo, Carla M.N.; Pires, Marcal J.R., E-mail: suzana.ferrarini@gmail.com [Faculdade de Quimica, Pontificia Universidade Catolica do Rio Grande do Sul, Porto Alegre, RS (Brazil); Maia, Sandra Maria [Instituto de Quimica, Universidade Federal do Rio Grande do Sul, Porto Alegre, RS (Brazil)

2012-07-01

Classification of waste wood treated with chromated copper arsenate (CCA) and boron/fluorine preservatives, according to NBR 10004, was investigated. The leaching test (ABNT NBR 10005) for As and Cr, and solubilization test (ABNT NBR 10006) for F, were applied to out-of-service wooden poles. Concentrations of As and Cr in leachates were determined by ICP-MS and of F by ESI. Values for As were higher than 1 mg L{sup -1} classifying the waste as hazardous material (Class I) whereas values for F (> 1.5 mg L{sup -1}) were non-hazardous but indicated non-inert material (Class IIA). (author)

REMOVAL COPPER, CHROMIUM, ARSENIC FROM OUT-OF- SERVICE CCA-TREATED WOOD MATERIALS

Directory of Open Access Journals (Sweden)

Engin Derya Gezer

2004-11-01

Full Text Available Remediation can be defined as removing copper, chromium and arsenic from out-of-service CCA treated wood products. There are some various remediation methods that can be applied to remove copper, chromium and arsenic from out-of service CCA treated wood products in order to re-use that wooden materials and minimize adverse impacts of those out-of service CCA treated wood to environment, human health, animals and other living organisms. In this study, those applied various remediation methods to remove copper, chromium and arsenic were summarized.

Evaluation of Mechanisms of Alteration and Humification of PAHs for Water Quality Management

OpenAIRE

Sims, Ronald C.; Abbott, Carolyn K.

1992-01-01

Introduction: Creosote-pentachlorophenol (PCP) is a mixture commonly used as a wood preservative in the U.S. (1). A 1988 survey (2) indicated that 1,397 wood preserving waste contaminated sites exist in the United States consisting of 555 active wood treatment plants and 842 inactive plants. Stinson (3) indentifed 58 wood preserving sites on the National Priorities List, of which 51 have PCP and/or creosote or po...

Movement of pentachlorophenol in unsaturated soil by electrokinetics

Energy Technology Data Exchange (ETDEWEB)

Harbottle, M.; Sills, G. [Dept. of Engineering Science, Oxford (United Kingdom); Jackman, S. [Dept. of Engineering Science, Oxford (United Kingdom)]|[NERC Centre for Ecology and Hydrology, Oxford (United Kingdom); Thompson, I. [NERC Centre for Ecology and Hydrology, Oxford (United Kingdom)

2001-07-01

Electrokinetic experiments have been performed on unsaturated natural soil specimens artificially contaminated with pentachlorophenol. Movement of pentachlorophenol within the soil mass has been demonstrated, but no contaminant was discovered in any effluent fluids. The results indicate that it may be possible to improve the bioavailability of the pollutant to degradative microorganisms using electrokinetics, by moving the chemical and microbes relative to each others. (orig.)

Amount of leachant and water absorption levels of wood treated with borates and water repellents.

Science.gov (United States)

Baysal, Ergun; Sonmez, Abdullah; Colak, Mehmet; Toker, Hilmi

2006-12-01

Wood protection efficacy of borates against biological agents, flame retardancy, and suitability to the environment is well known. Since borates can be applied to timber as water based solutions, they are preferred economically as well. Even though they are highly mobile in wood, boron compounds are widely used in timber preservation. Borates migrate in liquid and increase the hygroscopicity of wood in damp conditions. This study deals with the physical restriction of water access in wood by impregnating water repellent agents into wood to limit amount of leachant and water absorption levels of wood after boron treatment. Borates were incorporated with polyethylene glycol-400 (PEG-400) their bulking effect in wood was considered. Results indicated that the amount of leachates from wood treated with borates in PEG-400 was remarkably higher compared to those of wood treated with the aqueous solutions of borates. Water absorption (WA) levels of wood treated with aqueous solutions of borates were higher than those of their treated samples with the solutions in PEG-400. Secondary treatments of wood with the water repellent (WR) chemicals following borate impregnation reduced the leaching of chemicals from wood in water and also WA of the specimens were less than those of the wood treated with only borates from aqueous and PEG solutions. Styrene (St) was the most effective monomer among the other agents used in terms of immobility effect on borates and WA.

Effect of different extracting solutions on the electrodialytic remediation of CCA-treated wood waste Part I. - Behaviour of Cu and Cr

DEFF Research Database (Denmark)

Velizarova, E.; Ribeiro, A. B.; Mateus, E.

2004-01-01

Removal of Cu and Cr from chromated copper arsenate (CCA)-treated wood waste under batch electrodialytic conditions was studied. The effect of different types of extracting solutions, such as deionised water or aqueous solutions of NaCl, formic acid, oxalic acid, and EDTA, on the magnitude...... and direction of the fluxes of Cu- and Cr-containing species in the electrodialytic cell was investigated. Oxalic acid was found to have the best performance if simultaneous removal of the two elements is required (removal efficiencies of 80.5% for Cu and 87.4% for Cr, respectively). A mixture of oxalic acid...... and formic acid also led to similar removal efficiencies. In these experiments, the target elements were accumulated in both the anode and cathode compartments of the electrodialytic cell due to the formation of negatively charged complexes with the organic acids used besides the free cationic forms...

Health assessment for Southern Maryland Wood Treating (SMWT) National Priorities List (NPL) Site, Hollywood, St. Mary's County, Maryland, Region 3. CERCLIS No. MDD980704852. Final report

Energy Technology Data Exchange (ETDEWEB)

1989-04-10

The Southern Maryland Wood Treating National Priorities List site is located in Hollywood, St. Mary's County, Maryland. Approximately 12,000 gallons of dioxin-contaminated wastes and 2,000 gallons of wastes contaminated with volatile organic compounds or polynuclear aromatic hydrocarbons, or both, remain in on-site tanks used during wood treatment operations. Until remediation of the site is completed there is a potential public health concern from dermal absorption, ingestion, or inhalation of contaminants from groundwater, surface water, sediments, soil, and contaminated on-site structures.

Creosote movement from treated wood immersed in fresh water

Science.gov (United States)

Sung-Mo Kang; Jeffrey J. Morrell; John Simonsen; Stan Lebow

2005-01-01

Creosote has a long history of successful use as a wood preservative, but polycyclic aromatic hydrocarbons in this preservative have raised environmental concerns, particularly when creosote-treated wood is used in aquatic environments. A number of models have been developed to predict the risk of creosote use in aquatic environments, but one limitation of these models...

Fluidized-Bed Gasification of Plastic Waste, Wood, and Their Blends with Coal

Directory of Open Access Journals (Sweden)

Lucio Zaccariello

2015-08-01

Full Text Available The effect of fuel composition on gasification process performance was investigated by performing mass and energy balances on a pre-pilot scale bubbling fluidized bed reactor fed with mixtures of plastic waste, wood, and coal. The fuels containing plastic waste produced less H2, CO, and CO2 and more light hydrocarbons than the fuels including biomass. The lower heating value (LHV progressively increased from 5.1 to 7.9 MJ/Nm3 when the plastic waste fraction was moved from 0% to 100%. Higher carbonaceous fines production was associated with the fuel containing a large fraction of coal (60%, producing 87.5 g/kgFuel compared to only 1.0 g/kgFuel obtained during the gasification test with just plastic waste. Conversely, plastic waste gasification produced the highest tar yield, 161.9 g/kgFuel, while woody biomass generated only 13.4 g/kgFuel. Wood gasification showed a carbon conversion efficiency (CCE of 0.93, while the tests with two fuels containing coal showed lowest CCE values (0.78 and 0.70, respectively. Plastic waste and wood gasification presented similar cold gas efficiency (CGE values (0.75 and 0.76, respectively, while that obtained during the co-gasification tests varied from 0.53 to 0.73.

Environmental issues: New techniques for managing and using wood fuel ash

Energy Technology Data Exchange (ETDEWEB)

Fehrs, J.E.; Donovan, C.T. [C.T. Donovan Associates, Inc., Burlington, VT (United States)

1993-12-31

Continued research and development of environmentally-acceptable and cost-effective end uses for wood ash is having a significant affect on the ability to use wood and wood waste for fuel. This is particularly true for ash resulting from treated wood combustion. Concerns about the contents of ash from wood containing paint, stain, preservatives, or other chemicals is one of the largest regulatory barriers to its use as fuel. The purpose of this paper is to: (1) Identify the physical and chemical characteristics of ashes produced from the combustion of untreated and treated wood; (2) Explain the types of {open_quotes}clean, untreated{close_quotes} and {open_quotes}treated{close_quotes} wood that are likely to produce ash that can beneficially used; (3) Describe existing and potential products and end uses for untreated and treated wood ash.

Life-cycle assessment for power generation from wood fuels and wood wastes; Oekobilanz fuer die Stromerzeugung aus Holzbrennstoffen und Altholz

Energy Technology Data Exchange (ETDEWEB)

Jungbluth, N.; Frischknecht, R.; Faist, M.

2002-07-01

This reworked final report for the Swiss Federal Office of Energy (SFOE) presents the results of life-cycle assessments made of four wood-fired systems with the goal of analysing the possibilities of labelling such plants with the Swiss eco-label 'Naturemade Star'. In addition to these case studies, three standard technologies were modelled, whereby in two of the models different waste gas filtering methods were considered. In the third model, electricity is produced from waste wood and features an advanced waste gas treatment system. The report describes the various plants and draws up eco-balances for them. Pollution emissions, such as dust, oxides of nitrogen and sulphur dioxide, are discussed and plant operation and assessment are looked at. Certification to 'Naturemade Star' standards is checked out for the case-study plant examples and for the standard plant proposed. A further eco-balance is drawn up for wood-fired power generation with impact allocated to heat and power generation based on exergy content. An appendix provides details on the physical parameters of wood and on the methods used for impact assessment.

Drying wood waste with a pulse combustion dryer

Energy Technology Data Exchange (ETDEWEB)

Buchkowski, A.G. [Spectrum Engineering Corp., Ltd., Peterborough, Ontario (Canada); Kitchen, J.A. [John A. Kitchen, Ltd., Hastings, Ontario (Canada)

1993-12-31

There is a vast amount of wood waste available to be used as an alternate fuel if its moisture could be reduced efficiently. Tests have been conducted to assess an industrial dryer using pulse combustion as a heating source for drying wood waste; specifically sawdust and pulverized wet hog fuel. Pulse combustion offers the advantage of high heat transfer, efficient combustion, and low NO{sub x} emissions. The material is injected into the exhaust gases in the tailpipe of the combustor which uses natural gas or propane as a fuel. The turbulence created by the pulsations enhance the drying process by reducing the boundary layer thicknesses. The materials is further dried in a rotary drum. The material has been dried without scorching or burning in tests where the inlet moisture content has been as high as 60% on a wet basis. The outlet moisture contents achieved have typically been 10%. Analysis of the test data and cost estimates of the equipment indicate that the pulse combustion drying system is at least comparable to existing systems in terms of operating costs, and offers very significant savings in capital costs. Testing with various other materials such as wood pulp, sludges and peat is continuing to further assess the equipment`s performance.

Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

Directory of Open Access Journals (Sweden)

Teng-Chun Yang

2017-03-01

Full Text Available This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP, and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature.

Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

Science.gov (United States)

Yang, Teng-Chun; Chien, Yi-Chi; Wu, Tung-Lin; Hung, Ke-Chang; Wu, Jyh-Horng

2017-01-01

This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP), and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR) of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature. PMID:28772726

Role of construction debris in release of copper, chromium, and arsenic from treated wood structures

Science.gov (United States)

Stan T. Lebow; Steven A. Halverson; Jeffrey J. Morrell; John. Simonsen

Recent research on the release of wood preservatives from treated wood used in sensitive environments has not considered the potential contribution from construction residues. This study sought to develop leaching rate data for small construction debris and compare those to the release rate from treated wood itself. Western hemlock boards were pressure treated with...

Exposure testing of fasteners in preservative treated wood : gravimetric corrosion rates and corrosion product analyses

Science.gov (United States)

Samuel L. Zelinka; Rebecca J. Sichel; Donald S. Stone

2010-01-01

Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27oC at 100% relative humidity for 1 year. The...

Co-combustion of gasified contaminated waste wood in a coal fired power plant

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This project demonstrates the technical and economical feasibility of the producing and cofiring of product gas from demolition waste wood. For this purpose LCV product gas is generated in an atmospheric circulating fluidized bed (CFB) gasification plant, cooled and cleaned and transported to the boiler of a 600 MWe pulverized coal fired power plant. Gas cooling and cleaning takes place in a waste heat boiler and a multi stage wet gas cleaning train. Steam raised in the waste heat boiler is exported to the power plant. On an annual basis 70,000 tons of steam coal are substituted by 150,000 tons of contaminated demolition waste wood (50,000 tons oil equivalent), resulting in a net CO2 emission reduction of 170,000 tons per year, while concurrently generating 205 GWh of electrical power. The wood gasification plant was built by NV EPZ (now incorporated in Essent Energi BV) for Amergas BV, now a 100% subsidiary of Essent Energie BV. The gasification plant is located at the Amer Power Station of NV EPZ Production (now Essent Generation) at Geertruidenberg, The Netherlands. Demonstrating several important design features in wood gasification, the plant started hot service in the Spring of 2000, with first gasification accomplished in the Summer of 2000 and is currently being optimized. (au)

Resistance of treated rubber wood ( Hevea brasiliensis ) to termite ...

African Journals Online (AJOL)

Spent rubber trees from a 25 year old plantation were cut, sawn and treated with Copper Chromium Arsenate (CCA) and Cashew Nut Shell Liquid (CNSL). Two sets of wood samples were treated with CCA and CNSL respectively while the third set was not treated to serve as control. The three sets were exposed to termite ...

Physical and mechanical properties of flakeboard produced from recycled CCA-treated wood

Science.gov (United States)

W. Li; T.F. Shupe; Chung-Yun Hse

2004-01-01

Chromated copper arsenate (CCA) treated wood has been most widely used in North America since the 1970s for many exterior applications such as decks, fences, playground equipment, utility poles, and others. A large volume of CCA-treated wood is currently coming out of service. Traditional disposal methods such as landfilling and incineration are not without adverse...

Chemical remediation of wood treated with micronised, nano or soluble copper preservatives

Science.gov (United States)

Saip Nami Kartal; Evren Terzi; Bessie Woodward; Carol A. Clausen; Stan T. Lebow

2013-01-01

The potential for extraction of copper from wood treated with micronised, nano or soluble forms of copper has been evaluated in view of chemical remediation. In focus were EDTA, oxalic acid, bioxalate, and D-gluconic acid for extraction of Cu from treated wood. Bioxalate extractions for 24 h resulted in Cu removal over 95% for all tested...

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

Energy Technology Data Exchange (ETDEWEB)

Das, Oisik [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Bhattacharyya, Debes [Department of Mechanical Engineering, Center for Advanced Composite Materials, University of Auckland, Auckland 1142 (New Zealand)

2015-04-15

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted by manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications.

A novel approach in organic waste utilization through biochar addition in wood/polypropylene composites

International Nuclear Information System (INIS)

Das, Oisik; Sarmah, Ajit K.; Bhattacharyya, Debes

2015-01-01

Highlights: • Biochar made from waste wood was added with wood polypropylene composites. • 24% biochar gave the best mechanical properties. • 6% biochar had no effect on physico-mechanical properties of composites. • Coupling agent remained unreacted in composites having higher amount of biochar. - Abstract: In an attempt to concurrently address the issues related to landfill gas emission and utilization of organic wastes, a relatively novel idea is introduced to develop biocomposites where biochar made from pyrolysis of waste wood (Pinus radiata) is added with the same wood, plastic/polymer (polypropylene) and maleated anhydride polypropylene (MAPP). Experiments were conducted by manufacturing wood and polypropylene composites (WPCs) mixed with 6 wt%, 12 wt%, 18 wt%, 24 wt%, and 30 wt% biochar. Though 6 wt% addition had similar properties to that of the control (composite without biochar), increasing biochar content to 24 wt% improved the composite’s tensile/flexural strengths and moduli. The biochar, having high surface area due to fine particles and being highly carbonised, acted as reinforcing filler in the biocomposite. Composites having 12 wt% and 18 wt% of biochar were found to be the most ductile and thermally stable, respectively. This study demonstrates that, WPCs added with biochar has good potential to mitigate wastes while simultaneously producing biocomposites having properties that might be suited for various end applications

40 CFR 60.3066 - What are the emission limitations for air curtain incinerators that burn only wood waste, clean...

Science.gov (United States)

2010-07-01

... air curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3066 Section 60... Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3066 What are the...

76 FR 13616 - Picayune Wood Treating Site Picayune, Pearl River County, MS; Notice of Settlement

Science.gov (United States)

2011-03-14

... ENVIRONMENTAL PROTECTION AGENCY [Docket EPA-RO4-SFUND-2011-0201, FRL-9280-3] Picayune Wood... entered into a settlement for reimbursement of past response costs concerning the Picayune Wood Treating... No. EPA-RO4- SFUND-2011-0201 or Site name Picayune Wood Treating Superfund Site by one of the...

Catalytic photooxidation of pentachlorophenol using semiconductor nanoclusters

Energy Technology Data Exchange (ETDEWEB)

WILCOXON,JESS P.

2000-04-17

Pentachlorophenol (PCP) is a toxic chlorinated aromatic molecule widely used as fungicide, a bactericide and a wood preservation, and thus ubiquitous in the environment. The authors report photo-oxidation of PCP using a variety of nanosize semiconductor metal oxides and sulfides in both aqueous and polar organic solvents and compare the photo-oxidation kinetics of these nanoclusters to widely studied bulk powders like Degussa P-25 TiO{sub 2} and CdS. They study both the light intensity dependence of PCP photooxidation for nanosize SnO{sub 2} and the size dependence of PCP photooxidation for both nanosize SnO{sub 2} and MoS{sub 2}. They find an extremely strong size dependence for the latter which they attribute to its size-dependent band gap and the associated change in redox potentials due to quantum confinement of the hole-electron pair. The authors show that nanosize MoS{sub 2} with a diameter of d=3.0 nm and an absorbance edge of {approximately}450 nm is a very effective photooxidation catalyst for complete PCP mineralization, even when using only visible light irradiation.

Corrosion of metals in treated wood examined by synchrotron based xanes and XFM

Science.gov (United States)

Samuel L. Zelinka; Joseph E. Jakes; Grant T. Kirker; Leandro Passarini; Barry Lai

2016-01-01

Copper based waterborne wood preservatives are frequently used to extend the service life of wood products used in outdoor environments. While these copper based treatments protect the wood from fungal decay and insect attack, they increase the corrosion of metals embedded or in contact with the treated wood. Over the past ten years, several studies have looked at the...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Science.gov (United States)

2010-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Requirements for Commercial and Industrial Solid Waste Incineration Units That Commenced Construction On or Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or...

Mycoremediation of wood and soil from an old sawmill area contaminated for decades

Energy Technology Data Exchange (ETDEWEB)

Valentín, Lara; Oesch-Kuisma, Hanna; Steffen, Kari T.; Kähkönen, Mika A.; Hatakka, Annele; Tuomela, Marja, E-mail: marja.tuomela@helsinki.fi

2013-09-15

Highlights: • We performed experiments with non-sterile soil and wood with aged contamination. • We isolated fungal strains from a saw mill site with chlorophenols contamination. •Fungal strains were screened for tolerance to native microbes and contamination. • The best fungi degraded chlorophenols and chlorinated dibenzo-p-dioxins and -furans. -- Abstract: We investigated the potential of white-rot and litter-decomposing fungi for the treatment of soil and wood from a sawmill area contaminated with aged chlorinated phenols, dibenzo-p-dioxins and furans (PCDD/F). Eight screening assays with emphasis on application of non-sterile conditions were carried out in order to select the strains with capability to withstand indigenous microbes and contamination. Nine fungi were then selected for degrading pentachlorophenol (PCP), and 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP) and mineralizing radiolabelled pentachlorophenol ({sup 14}C-PCP) in non-sterile soil or wood during 15 weeks of incubation. Soil indigenous microbes and fungal inoculated soil (fungal inoculum + indigenous microbes) achieved similar degradation of PCP and 2,3,4,6-TeCP and mineralization of {sup 14}C-PCP. However, the mineralization rate of {sup 14}C-PCP by indigenous microbes was much slower than that boosted by fungal inoculum. The litter-decomposing fungus (LDF) Stropharia rugosoannulata proved to be a suitable fungus for soil treatment. This fungus mineralized 26% of {sup 14}C-PCP and degraded 43% of 2,3,4,6-TeCP and 73% of PCP. Furthermore, S. rugosoannulata attained 13% degradation of PCDD/F (expressed as WHO-Toxic Equivalent). In wood, white-rot fungi grew and degraded chlorophenols better than LDF. No efficient indigenous degraders were present in wood. Interestingly, production of toxic chlorinated organic metabolites (anisoles and veratroles) by LDF in wood was negligible.

Mycoremediation of wood and soil from an old sawmill area contaminated for decades

International Nuclear Information System (INIS)

Valentín, Lara; Oesch-Kuisma, Hanna; Steffen, Kari T.; Kähkönen, Mika A.; Hatakka, Annele; Tuomela, Marja

2013-01-01

Highlights: • We performed experiments with non-sterile soil and wood with aged contamination. • We isolated fungal strains from a saw mill site with chlorophenols contamination. •Fungal strains were screened for tolerance to native microbes and contamination. • The best fungi degraded chlorophenols and chlorinated dibenzo-p-dioxins and -furans. -- Abstract: We investigated the potential of white-rot and litter-decomposing fungi for the treatment of soil and wood from a sawmill area contaminated with aged chlorinated phenols, dibenzo-p-dioxins and furans (PCDD/F). Eight screening assays with emphasis on application of non-sterile conditions were carried out in order to select the strains with capability to withstand indigenous microbes and contamination. Nine fungi were then selected for degrading pentachlorophenol (PCP), and 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP) and mineralizing radiolabelled pentachlorophenol ( 14 C-PCP) in non-sterile soil or wood during 15 weeks of incubation. Soil indigenous microbes and fungal inoculated soil (fungal inoculum + indigenous microbes) achieved similar degradation of PCP and 2,3,4,6-TeCP and mineralization of 14 C-PCP. However, the mineralization rate of 14 C-PCP by indigenous microbes was much slower than that boosted by fungal inoculum. The litter-decomposing fungus (LDF) Stropharia rugosoannulata proved to be a suitable fungus for soil treatment. This fungus mineralized 26% of 14 C-PCP and degraded 43% of 2,3,4,6-TeCP and 73% of PCP. Furthermore, S. rugosoannulata attained 13% degradation of PCDD/F (expressed as WHO-Toxic Equivalent). In wood, white-rot fungi grew and degraded chlorophenols better than LDF. No efficient indigenous degraders were present in wood. Interestingly, production of toxic chlorinated organic metabolites (anisoles and veratroles) by LDF in wood was negligible

Effects of Treated Wood Flour on Physico-Mechanical Properties of ...

African Journals Online (AJOL)

Wood flour was crushed in to particle size and given two surface treatments each with alkali and 3-chloro-2 hydroxylpropyltrimethylammoniumchloride. The raw, alkali-treated and bonding agent treated fibers were used as natural rubber composites. The samples were used to produce fiber-reinforced natural rubber ...

40 CFR 62.14820 - How must I monitor opacity for air curtain incinerators that burn 100 percent wood wastes, clean...

Science.gov (United States)

2010-07-01

... curtain incinerators that burn 100 percent wood wastes, clean lumber, and/or yard waste? 62.14820 Section... Requirements for Commercial and Industrial Solid Waste Incineration Units That Commenced Construction On or Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or...

CCA retention and its effects on the bonding performance of decommissioned treated wood: a preliminary study

Science.gov (United States)

Cheng Piao; Todd F. Shupe; Mark Gibson; Chung Y. Hse

2009-01-01

Chromated copper arsenate (CCA) continues to be widely used as a wood preservative for industrial uses in the U.S. Disposal of treated wood is a potential long-term environmental liability. Current practices for disposing of decommissioned preservative-treated wood include landfilling and incineration, which are increasingly impractical due to environmental...

40 CFR 60.3067 - How must I monitor opacity for air curtain incinerators that burn only wood waste, clean lumber...

Science.gov (United States)

2010-07-01

... curtain incinerators that burn only wood waste, clean lumber, and yard waste? 60.3067 Section 60.3067... Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3067 How must I monitor opacity for...

Fractionation of heavy metals in liquefied chromated copper arsenate (CCA)-treated wood sludge using a modified BCR-sequential extraction procedure

Science.gov (United States)

Hui Pan; Chung-Yun Hse; Robert Gambrell; Todd F. Shupe

2009-01-01

Chromated copper arsenate (CCA)-treated wood was liquefied with polyethylene glycol/glycerin and sulfuric acid. After liquefaction, most CCA metals (98% As, 92% Cr, and 83% Cu) were removed from liquefied CCA-treated wood by precipitation with calcium hydroxide. The original CCA-treated wood and liquefied CCA-treated wood sludge were fractionated by a modified...

Leachability of boron from wood treated with natural and semi-synthetic polymers and calcium precipitating agent

Science.gov (United States)

S. N. Kartal; F. Green

2003-01-01

Several fixation systems to limit or decrease boron leachability from treated wood have been developed. Some attempts have relied on limiting of water penetration of treated wood using water repellents, monomer and polymer systems. On the other hand, non-toxic polymers such as proteins were tried to reduce amount of boron leached from wood (Thevenon et al. 1997, 1998...

Uptake, translocation, and transformation of pentachlorophenol in soybean and spinach plants

International Nuclear Information System (INIS)

Casterline, J.L. Jr.; Barnett, N.M.; Ku, Y.

1985-01-01

Soybean plants were grown for 90 days and spinach plants for 64 days in a mixture of sterilized greenhouse soil and sand containing 10 ppm pentachlorophenol. All plant parts and soil samples were extracted and separated into nonpolar and polar fractions. Major nonpolar and polar metabolites were identified by gas-liquid chromatography and mass spectrometry. Nonpolar fractions from both soybean and spinach plants were found to contain pentachlorophenol and its metabolites, 2,3,4,6-tetrachlorophenol, methoxytetrachlorophenol, 2,3,4,6-tetrachloroanisole, and pentachloroanisole. Cleavage of polar metabolites from the soybean plants by acid hydrolysis yielded organic solvent-extractable products. These products were identified as pentachlorophenol, 2,3,4,6-tetrachlorophenol, and methoxytetrachlorophenol. Cleavage of polar materials from spinach plants yielded only pentachlorophenol. The polar metabolites from the soybean plants were also subjected to enzymatic cleavage by beta-glucosidase. The conjugates consisted mostly of O-glucosides of the same metabolites released by acid hydrolysis. Failure of hydrolysis by aryl sulfatase indicated that very little or no sulfates were present. The metabolites found in the plants were not detected in soil samples obtained from pots immediately after the plants were harvested

Wood ash to treat sewage sludge for agricultural use

Energy Technology Data Exchange (ETDEWEB)

White, R.K. [Clemson Univ., SC (United States)

1993-12-31

About 90% of the three million tons of wood ash generated in the United States from wood burning facilities is being landfilled. Many landfills are initiated tipping fees and/or restrictions on the disposal of special wastes such as ash. The purpose of this work was to evaluate (1) the feasibility of using wood ash to stabilize sewage sludge and (2) the fertilizer and liming value of the sludge/ash mixture on plant response and soil pH. Research showed that wood ash, when mixed with sludge, will produce a pH above 12.0, which meets US EPA criteria for pathogen reduction for land application on non-direct food chain crops. Different ratios of wood ash to sludge mixtures were tested and the 1:1 ratio (by weight) was found to be optimal. Five replications of wood ash from four sources were tested for moisture content, pH and fertilizer nutrients. The pH of the ash/sludge mixture (1:1) on day one ranged from 12.4 to 13.2. In most cases the pH remained the same over a 21 day test or only dropped 0.1 to 0.3 units. Analyses of the mixtures showed that heavy metal concentrations (As, B, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, S, Se, Zn) were low. The 1:1 ash/sludge mixture had a calcium carbonate equivalency of 17%. Green house pot studies using tall fescue grass were loadings of 300 to 750 pounds per acre of TKN-N than for 500 lb/acre of 10-10-10 commercial fertilizer. Plant tissue analysis showed N, P, K, Ca, and Mg levels to be within the sufficiency range for tall fescue.

Long-term soil accumulation of chromium, copper, and arsenic adjacent to preservative-treated wood.

Science.gov (United States)

S. Lebow; D. Foster; J. Evans

2004-01-01

Chromated copper arsenate (CCA) treated wood has been used extensively in outdoor applications. The Environmental Protection Agency (EPA) and CCA producers recently reached an agreement to limit future use of CCA for some types of applications. One area of concern is the long-term accumulation of leached CCA in soil adjacent to treated wood structures. Interpreting...

Exposure testing of fasteners in preservative treated wood: Gravimetric corrosion rates and corrosion product analyses

Energy Technology Data Exchange (ETDEWEB)

Zelinka, Samuel L., E-mail: szelinka@fs.fed.u [USDA Forest Products Laboratory, One Gifford Pinchot Drive, Madison, WI 53726 (United States); Sichel, Rebecca J. [College of Engineering, University of Wisconsin, Madison, WI 53706 (United States); Stone, Donald S. [Department of Materials Science and Engineering, College of Engineering, University of Wisconsin, Madison, WI 53706 (United States)

2010-12-15

Research highlights: {yields} The composition of the corrosion products was similar for the nail head and shank. {yields} Reduced copper was not detected on any of the fasteners. {yields} Measured corrosion rates were between 1 and 35 {mu}m year{sup -1}. - Abstract: Research was conducted to determine the corrosion rates of metals in preservative treated wood and also understand the mechanism of metal corrosion in treated wood. Steel and hot-dip galvanized steel fasteners were embedded in wood treated with one of six preservative treatments and exposed to 27 {sup o}C at 100% relative humidity for 1 year. The corrosion rate was determined gravimetrically and the corrosion products were analyzed with scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. Although the accepted mechanism of corrosion in treated wood involves the reduction of cupric ions from the wood preservative, no reduced copper was found on the corrosion surfaces. The galvanized corrosion products contained sulfates, whereas the steel corrosion products consisted of iron oxides and hydroxides. The possible implications and limitations of this research on fasteners used in building applications are discussed.

40 CFR 60.3064 - What must I do if I close my air curtain incinerator that burns only wood waste, clean lumber...

Science.gov (United States)

2010-07-01

... curtain incinerator that burns only wood waste, clean lumber, and yard waste and then restart it? 60.3064... Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3064 What...

40 CFR 60.3063 - When must I comply if my air curtain incinerator burns only wood waste, clean lumber, and yard...

Science.gov (United States)

2010-07-01

... incinerator burns only wood waste, clean lumber, and yard waste? 60.3063 Section 60.3063 Protection of... Units That Commenced Construction On or Before December 9, 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60.3063 When must I comply if my air curtain...

Assessment of the environmental effects associated with wooden bridges preserved with creosote, pentachlorophenol, or chromated copper arsenate

Science.gov (United States)

Kenneth M. Brooks

Timber bridges provide an economical alternative to concrete and steel structures, particularly in rural areas with light to moderate vehicle traffic. Wooden components of these bridges are treated with chromated copper arsenate type C (CCA), pentachlorophenol, or creosote to prolong the life of the structure from a few years to many decades. This results in reduced...

Scarcity on the market for wood wastes; Krapte op de markt voor afvalhout

Energy Technology Data Exchange (ETDEWEB)

De Boer, A. (ed.)

2004-05-01

An overview is given of the market for wood wastes in the Netherlands and how this affects the targets to use biomass. Several types of biomass must be imported, not only wood wastes, but also e.g. olive stones and cacao shells. [Dutch] Er dreigt in Nederland een krapte te ontstaan op de markt voor afvalhout, want de vraag vanuit de buitenlandse vezelplaatindustrie blijft constant, terwijl er vanuit de energiesector een groeiende vraag is. Om de beleidsdoelstellingen voor biomassa te kunnen halen zal er biomassa geimporteerd moeten worden. Daarbij kan het gaan om resthout of afvalhout, maar ook om andere biomassastromen zoals olijfpitten en cacaodoppen.

CORROSION AND CHEMICAL WASTE IN SAWBLADES STEEL USED IN WOOD

Directory of Open Access Journals (Sweden)

Paulo Fernando Trugilho

2002-01-01

Full Text Available The objective this work was to evaluate the chemical waste provoked by the wood on the sheets of steel used in the making of the mountains and cut tools. It was certain the correlationbetween the chemical waste and the extractive soluble in cold water, hot water and in the sequencetoluene and ethanol content. Two types of steel and twenty-seven species different from wood wereused. The corrosive agent, constituted of 50 g of fresh sawdust (moist mixed to 50 ml of distilledwater, it was prepared and placed inside of the plastic box, hermetically closed, on the samples ofsteel, which were totally immersed. The box was placed in a water bath pre-heated to 75°C, that themedium temperature of reaction is considered, that affects the sheet of the sawblade in operation. Thisgroup was operated to 80 rotations per minute (rpm. The time of reaction was of four hours. Afterthat time the corrosive agent was discarded and the samples were washed, dried and weighed. At theend, each sample was processed by a total period of forty hours. The chemical waste was evaluated by the weight difference suffered from beginning at the end of the experiment. For theresults it was observed that the Eucalyptus tradryphloia and the Eucalyptus phaeotricha the speciesthat provoked were, respectively, the largest and smaller chemical waste for the two types of steelappraised. Great variation exists in the chemical waste due to the effect of the species. The corrosionand chemical waste are especially related with the quality of the material solved in ethanol. The 1070steel were more attached than the 6170 steel.

ASSESSING CHILDREN'S EXPOSURES TO THE WOOD PRESERVATIVE CCA (CHROMATED COPPER ARSENATE) ON TREATED PLAYSETS AND DECKS

Science.gov (United States)

Concerns have been raised regarding the safety of young children contacting arsenic and chromium residues while playing on and around Chromated Copper Arsenate (CCA) treated wood playground structures and decks. Although CCA registrants voluntarily canceled treated wood for re...

Chapter 14: Evaluating the Leaching of Biocides from Preservative-Treated Wood Products

Science.gov (United States)

Stan T. Lebow

2014-01-01

Leaching of biocides is an important consideration in the long term durability and any potential for environmental impact of treated wood products. This chapter discusses factors affecting biocide leaching, as well as methods of evaluating rate and quantity of biocide released. The extent of leaching is a function of preservative formulation, treatment methods, wood...

Guide for minimizing the effect of preservative-treated wood on sensitive environments

Science.gov (United States)

Stan T. Lebow; Michael Tippie

2001-01-01

Preservative-treated wood is often used for construction of highway and foot bridges, wetland boardwalks, and other structures in or over water or sensitive environments. In these applications it is important that release of preservative from the wood into the environment is minimized. This publication addresses this concern by describing the various types of pressure-...

Subterranean Termite Resistance of Polystyrene-Treated Wood from Three Tropical Wood Species

Directory of Open Access Journals (Sweden)

Yusuf Sudo Hadi

2016-07-01

Full Text Available The objective of this work was to investigate the resistance of three Indonesian wood species to termite attack. Samples from sengon (Falcataria moluccana, mangium (Acacia mangium, and pine (Pinus merkusii were treated with polystyrene at loading levels of 26.0%, 8.6%, and 7.7%, respectively. Treated and untreated samples were exposed to environmental conditions in the field for 3 months. Untreated specimens of sengon, mangium, and pine had resistance ratings of 3.0, 4.6, and 2.4, respectively, based on a 10-point scale from 0 (no resistance to 10 (complete or near-complete resistance. Corresponding resistance values of 7.8, 7.2, and 8.2 were determined for specimens treated with polystyrene. Overall weight loss values of 50.3%, 23.3%, and 66.4% were found for untreated sengon, mangium, and pine samples, respectively; for treated samples, the values were 7.6%, 14.4%, and 5.1%, respectively. Based on the findings in this study, overall resistance to termite attack was higher for treated samples compared to untreated samples.

Accelerated weathering of fire-retardant-treated wood for fire testing

Science.gov (United States)

Robert H. White

2009-01-01

Fire-retardant-treated products for exterior applications must be subjected to actual or accelerated weathering prior to fire testing. For fire-retardant-treated wood, the two accelerated weathering methods have been Method A and B of ASTM D 2898. The rain test is Method A of ASTM D 2898. Method B includes exposures to ultraviolet (UV) sunlamps in addition to water...

A non-destructive approach for assessing decay in preservative treated wood

NARCIS (Netherlands)

Machek, L.; Edlund, M.L.; Sierra-Alvarez, R.; Militz, H.

2004-01-01

This study investigated the suitability of the non-destructive vibration-impulse excitation technique to assess the attack of preservative-treated wood in contact with the ground. Small stakes (10×5×100 mm3) of treated and untreated Scots pine sapwood were exposed to decay in laboratory-scale

LOW COST SOLIDIFICATION/STABILIZATION TREATMENT FOR SOILS CONTAMINATED WITH DIOXIN, PCP AND CREOSOTE

Science.gov (United States)

The USEPA's NRMRL conducted successful treatability tests of innovative solidification/stabilization (S/S) formulations to treat soils contaminated with dioxins, pentachlorophenol (PCP), and creosote from four wood preserving sites. Formulations developed during these studies wer...

Formation of dioxins and furans during combustion of treated wood

Energy Technology Data Exchange (ETDEWEB)

Tame, Nigel W.; Dlugogorski, Bogdan Z.; Kennedy, Eric M. [Process Safety and Environment Protection Research Group, School of Engineering, The University of Newcastle, Callaghan, NSW 2308 (Australia)

2007-08-15

Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F, dioxin) are produced in combustion of wood treated with copper-based preservatives. This review summarises and analyses the pertinent literature on the role of preservatives in the formation of dioxin in the low-temperature, vitiated environment that exists in the domestic combustion of wood, and in large-scale fires. Until recently, the role of preservatives was not thoroughly examined in the literature with respect to fires, as incineration attracted most of the research focus. However, latest studies have demonstrated that some current and emerging wood preservatives significantly increase dioxin formation during combustion in domestic stoves and in fires. The following pathways are identified: (i) copper, a common biocide that is chemically bound to the wood, is an important dioxin catalyst, (ii) preservative metals promote smouldering of wood char following cessation of flaming, providing the required temperature environment for dioxin formation, and (iii) chlorinated organics added as secondary preservative components yield dioxin precursors upon thermal decomposition. These conclusions indicate that it remains hazardous to dispose of preservative impregnated timber via domestic combustion even if arsenic is not present. (author)

Impact of chromated copper arsenate (CCA) in wood mulch.

Science.gov (United States)

Townsend, Timothy G; Solo-Gabriele, Helena; Tolaymat, Thabet; Stook, Kristin

2003-06-20

The production of landscape mulch is a major market for the recycling of yard trash and waste wood. When wood recovered from construction and demolition (C&D) debris is used as mulch, it sometimes contains chromated copper arsenate (CCA)-treated wood. The presence of CCA-treated wood may cause some potential environmental problems as a result of the chromium, copper, and arsenic present. Research was performed to examine the leachability of the three metals from a variety of processed wood mixtures in Florida. The mixtures tested included mixed wood from C&D debris recycling facilities and mulch purchased from retail outlets. The synthetic precipitation leaching procedure (SPLP) was performed to examine the leaching of chromium, copper and arsenic. Results were compared to Florida's groundwater cleanup target levels (GWCTLs). Eighteen of the 22 samples collected from C&D debris processing facilities leached arsenic at concentrations greater than Florida's GWCTL of 50 microg/l. The mean leachable arsenic concentration for the C&D debris samples was 153 microg/l with a maximum of 558 microg/l. One of the colored mulch samples purchased from a retail outlet leached arsenic above 50 microg/l, while purchased mulch samples derived from virgin materials did not leach detectable arsenic (<5 microg/l). A mass balance approach was used to compute the potential metal concentrations (mg/kg) that would result from CCA-treated wood being present in wood mulch. Less than 0.1% CCA-treated wood would cause a mulch to exceed Florida's residential clean soil guideline for arsenic (0.8 mg/kg).

The challenge of bonding treated wood

Science.gov (United States)

Charles R. Frihart

2004-01-01

Wood products are quite durable if exposure to moisture is minimized; however, most uses of wood involve considerable exposure to moisture. To preserve the wood, chemicals are used to minimize moisture pickup, to prevent insect attack, and/or to resist microbial growth. The chemicals used as preservatives can interfere with adhesive bonds to wood. Given the many...

Sodium alginate adhesives as binders in wood fibers/textile waste fibers biocomposites for building insulation.

Science.gov (United States)

Lacoste, Clément; El Hage, Roland; Bergeret, Anne; Corn, Stéphane; Lacroix, Patrick

2018-03-15

Alginate derived from seaweed is a natural polysaccharide able to form stable gel through carbohydrate functional groups largely used in the food and pharmaceutical industry. This article deals with the use of sodium alginate as an adhesive binder for wood fibres/textile waste fibres biocomposites. Several aldehyde-based crosslinking agents (glyoxal, glutaraldehyde) were compared for various wood/textile waste ratios (100/0, 50/50, 60/40, 70/30 and 0/100 in weight). The fully biomass derived composites whose properties are herewith described satisfy most of the appropriate requirements for building materials. They are insulating with a thermal conductivity in the range 0.078-0.089 W/m/K for an average density in the range 308-333 kg/m3 according to the biocomposite considered. They are semi-rigid with a maximal mechanical strength of 0.84 MPa under bending and 0.44 MPa under compression for 60/40 w/w wood/textile waste biocomposites with a glutaraldehyde crosslinking agent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Superfund Record of Decision (EPA Region 3): Southern Maryland Wood Treating Site, Hollywood, Maryland (first remedial action) June 1988. Final report

Energy Technology Data Exchange (ETDEWEB)

1988-06-29

The Southern Maryland Wood Treating (SMWT) site is located in Hollywood, St. Mary's County, Maryland. The site is situated within a wetland area in a drainage divide such that runoff from the site discharges into Brooks Run and McIntosh Run tributaries, which flow into the Potomac River. The area surrounding the site is predominantly used for agricultural and residential purposes. Currently, part of the site is being used as a retail outlet for pretreated lumber and crab traps. The waste generated at the site included retort and cylinder sludges, process wastes, and material spillage. These wastes were in six onsite unlined lagoons. The primary contaminants of concern affecting the onsite ground water, soil, surface water, sediments, and debris include: VOCs, PNA, and base/neutral acid extractables. The selected remedial action for the site is included.

Wood preservatives and pressure-treated wood: considerations for historic-preservation projects

Science.gov (United States)

Ronald W. Anthony; Stan T. Lebow

2015-01-01

Wood, an abundant resource throughout most of the world, has been used as a building material for thousands of years. Many historic buildings have been built primarily of wood, and masonry and stone buildings generally have wood elements, both structural and architectural. As a biological material, wood is both remarkably complex and yet quite durable if well...

Electrodialytic removal of Cu, Cr, and As from chromated copper arsenate-treated timber waste

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, A.B.; Mateus, E.P.; Ottosen, L.M.; Bech-Nielsen, G.

2000-03-01

Waste of wood treated with chromated copper arsenate (CCA) is expected to increase in volume over the next decades. Alternative disposal options to landfilling are becoming more attractive to study, especially those that promote reuse. The authors have studied the electrodialytic removal of Cu, Cr, and As from CCA-treated timber wastes. The method uses a low-level direct current as the cleaning agent, combining the electrokinetic movement of ions in the matrix with the principle of electrodialysis. The technique was tested in four experiments using a laboratory cell on sawdust of an out-of-service CCA-treated Pinus pinaster Ait. pole. The duration of all the experiments was 30 days, and the current density was kept constant at 0.2 mA/cm{sup 2}. The experiments differ because in one the sawdust was saturated with water (experiment 1) and in the rest it was saturated with oxalic acid, 2.5, 5, and 7.5% (w/w), respectively, in experiments 2--4. The highest removal rates obtained were 93% of Cu, 95% of Cr, and 99% of As in experiment 2. Other experimental conditions might possibly optimize the removal rates.

Rapid microwave-assisted acid extraction of metals from chromated copper arsenate (CCA)-treated southern pine wood

Science.gov (United States)

Bin Yu; Chung Y. Hse; Todd F. Shupe

2009-01-01

The effects of acid concentration, reaction time, and temperature in a microwave reactor on recovery of CCA-treated wood were evaluated. Extraction of copper, chromium, and arsenic metals from chromated copper arsenate (CCA)-treated southern pine wood samples with three different acids (i.e., acetic acid, oxalic acid, and phosphoric acid) was investigated using in...

Special Analysis: Updated Analysis of the Effect of Wood Products on Trench Disposal Limits at the E-Area Low-Level Waste Facility

International Nuclear Information System (INIS)

Cook, J.R.

2001-01-01

This Special Analysis (SA) develops revised radionuclide inventory limits for trench disposal of low-level radioactive waste in the presence of wood products in the E-Area Low-Level Waste Facility. These limits should be used to modify the Waste Acceptance Criteria (WAC) for trench disposal. Because the work on which this SA is based employed data from tests using 100 percent wood products, the 40 percent limitation on wood products for trench (i.e., slit or engineered trench) disposal is not needed in the modified WAC

POLYMER COMPOSITES MODIFIED BY WASTE MATERIALS CONTAINING WOOD FIBRES

Directory of Open Access Journals (Sweden)

Bernardeta Dębska

2016-11-01

Full Text Available In recent years, the idea of sustainable development has become one of the most important require-ments of civilization. Development of sustainable construction involves the need for the introduction of innovative technologies and solutions that will combine beneficial economic effects with taking care of the health and comfort of users, reducing the negative impact of the materials on the environment. Composites obtained from the use of waste materials are part of these assumptions. These include modified epoxy mortar containing waste wood fibres, described in this article. The modification consists in the substitution of sand by crushed waste boards, previously used as underlays for panels, in quantities of 0%, 10%, 20%, 35% and 50% by weight, respectively. Composites containing up to 20% of the modifier which were characterized by low water absorption, and good mechanical properties, also retained them after the process of cyclic freezing and thawing.

Wood Flour Moulding Technology: Implications for Technical ...

African Journals Online (AJOL)

The intent of this article is to demonstrate how wood waste called sawdust or wood flour can be transformed by plastic moulding machine into items of economic value. Wood flour is wood reduced to very fine particle form. It can be waste product from saw mills, wood working plants or produced from selected dry wood by ...

Increasing Effort in Using the Waste of Mangrove Wood for Natural Dyes

International Nuclear Information System (INIS)

Kuntari-Sasas; Sri-Sunaryati; G, Isminingsih; Santosa; Mirtha

2000-01-01

The general function of mangrove forest is mainly for protecting thesustain ability of sea shore against the wave toss, however, the fishermenhas often used the mangrove wood to produce their ships, building and otherthings. Among others, this wood also contains of chromophore, tannine,furfurol and phtalic that has the possibility to serve as textile dyes,however its fixation ability to silk fiber in this dyes does not have strongfixation ability to silk fiber. In other to improve its color fastness it wasnecessary to do after treatment with mordant. In this study the waste fromthe mangrove in the form of shredded wood, wood bark or twig and small branchwere used as the raw material of the natural dyes. This materials werechopped as small as possible (into saw form) and being extracted in order toobtain the dyes as much as possible. As the result of this study wasaddressed to the small and medium scale industries, the extraction processwas carried out in a simple way using water as medium with various ratios inthe respected order 1:10; 1:20; 1:30; 1:40; and 1 :50. To obtain theextracted yields, the mangrove waste was extracted until it reached the ratioof 1/5 to the medium, the extracted sample was taken out to be extractedagain in fresh water as medium in the same ratio variation. This process wasrepeated until no more wood color to be extracted (± 9 repeats). Theextracted liquid was then put into evaporation, drying and grinded into dyespowder. The highest extracted yields was obtained by the ratio to medium(1:40 to 1:50) with 9.40% -9.48% extracted yields. The following experimentwas dyeing process to silk fabrics by using dyes powder or dyes liquidextracted from medium with ratio 1:40 mixture from first extraction up toforth extraction. The dyeing process was carried out without mordanting,pre-mordanting and post-mordanting, by means of Tawas (Al 2 K 2 (SO 4 ) 3 ) orTunjung (FeSO 4 . 7 H 2 O) as mordanting material. The dyed silk fabrics werethen tested for

LEATHER WASTE VALORISATION THROUGH MATERIAL INNOVATION: SOME PROPERTIES OF LEATHER WOOD FIBREBOARD

Directory of Open Access Journals (Sweden)

Axel M. RINDLER

2015-12-01

Full Text Available Due to the ever-increasing scarcity of resources and raw materials in the wood panels industry, it is imperative to look for suitable alternatives to the established resources. Therefore a combination of the traditionally used and newly explored sources may reveal highly innovative ways. The objective of this study is to provide an insight into the behavior of the material and possible new applications of those fiber/particle wood and waste leather composites. For this reason exclusively fibers of spruce were used for the trials. Wet white (WW leather particles and wet blue (WB leather particles were mixed with the wooden materials for the production of high density fibreboards. Besides the mechanical properties such as the internal bond (IB the bending strength (MOR and modulus of elasticity (MOE was analyzed. Further physical property as thickness swelling after 24h watering was investigated. To analyze how the density influences the behavior under thermal conditions, fiberboards with the densities 500, 700 and 900 kg/m³ were tested. The results of the material properties were influenced by the leather content of the panels. The results for the UF-bonded HDF boards show enhancement of the transverse IB with increasing wet blue leather content, whereas the other mechanical properties decline meanwhile. The thickness swelling showed higher values compared to the wood fibreboard. The results of this study underline the usefulness of integrating leather shavings to HDF and give an overview of their influence in wood fiber materials. The combination of the natural resource wood fiber and the leather waste products (Wet Blue and Wet White gives a very interesting new material, its mechanical properties allow a variety of possible application in future applications.

Recycling of wood products. Final report of the preliminary study project partly financed by the Finnish Wood Research Oy; Puutuotteiden kierraetys. Finnish Wood Research Oy:n osarahoittaman esiselvityshankkeen loppuraportti

Energy Technology Data Exchange (ETDEWEB)

Pirhonen, I.; Heraejaervi, H.; Saukkola, P.; Raety, T.; Verkasalo, E., Email: henrik.herajarvi@metla.fi

2011-07-01

The objective of this preliminary study was to clarify the present state of recycling of wood in Finland and Europe. In the work the control measures of recycling were examined. In Finland there will be a total amount of 850 000 tons of waste wood per year. Of this amount 670 000 tons is from construction and demolishing of buildings. Burning the wood to energy is technically and economically the most reasonable use of waste wood in Finland and in several other European countries where there is a long heating season. A lot of work has been done to find new ways of utilization. The objective of the European Union to increase the use of renewable natural resources in the energy production creates an additional demand to all kinds of wood, including waste wood. The waste legislation of Finland and EU is directing to recycling, not restricting it. Furthermore, the systems to try to create markets for products containing recycled materials are under development. In the future it is expected that the legislation is tightening and the burning of waste wood is no longer calculated as acceptable recycling. Other ways to utilize wood waste should then already be developed. Furthermore, the development and introduction of new recycling methods are of important significance also when marketing wood and wood products. The recycling should be taken into consideration already at the planning stage of the building

Understanding decay resistance, dimensional stability and strength changes in heat treated and acetylated wood

Science.gov (United States)

Roger M. Rowell; Rebecca E. Ibach; James McSweeny; Thomas Nilsson

2009-01-01

Reductions in hygroscopicity, increased dimensional stability and decay resistance of heat-treated wood depend on decomposition of a large portion of the hemicelluloses in the wood cell wall. In theory, these hemicelluloses are converted to small organic molecules, water and volatile furan-type intermediates that can polymerize in the cell wall. Reductions in...

Copper naphthenate: a proven solution for new wood preservative problems

Energy Technology Data Exchange (ETDEWEB)

McNair, W.S. [Merichem Chemicals and Refinery Services LLC, Houston, TX (United States); Loecner, P. [Pacific Gas and Electric, Davis, CA (United States)

2002-08-01

Today's engineers have the responsibility of considering cost, availability and climbability, as well as the environmental alternatives available to the traditional wood preservatives used in the production of utility poles: creosote, pentachlorophenol (PCP) and chromated copper arsenate (CCA). The leading alternative now emerging for utilities in this field is copper naphthenate. The authors present a case study that clearly demonstrates copper naphthenate as one of the most environmentally sensitive and effective wood preservative. When first introduced, copper naphthenate seemed to frequently result in early failure of the poles treated with this preservative. It was discovered that it was a phenomenon that had been largely exaggerated, and the failure rate was less than one per cent. A recent review has concluded that premature failures have basically disappeared. Several reasons can explain premature failures, such as pretreatment decay, improper sterilization/conditioning/drying, inadequate copper penetration and retention, and others. The long term effectiveness and performance of copper naphthenate has been documented in a number of field trials. The ultimate disposal of the product must be considered by the specifying engineer, and it is possible to dispose of copper naphthenate poles in a sanitary landfill. Due in part to recent manufacturing economies, the cost of copper naphthenate is similar to other oil-borne treatments. The case study of Pacific Gas and Electric was discussed. 7 refs., 2 figs.

Pentachlorophenol reduction in raw Cauca river water through activated carbon adsorption in water purification

Directory of Open Access Journals (Sweden)

Camilo Hernán Cruz Vélez

2008-09-01

Full Text Available Reducing chemical risk in raw water from the River Cauca (caused by the presence of pentachlorophenol and organic matter (real color, UV254 absorbance was evaluated at bench scale by using three treatment sequences: adsorption with powdered ac-tivated coal (PAC; adsorption – coagulation; and, adsorption – disinfection – coagulation. The results showed that although PAC is appropriate for pentachlorophenol removal, and its use together with the coagulant (aluminium sulphate significantly impro-ved phenolic compound and organic matter removal (promoting enhanced coagulation, the most efficient treatment sequence was adsorption – disinfection - coagulation, achieving minor pentachlorophenol levels than detection (1.56 μg/l and WHO li-mits (9μg/l due to the effect of chloride on PAC.

78 FR 67371 - Draft Report on Carcinogens Monographs for ortho-Toluidine and Pentachlorophenol and By-products...

Science.gov (United States)

2013-11-12

... Monographs for ortho-Toluidine and Pentachlorophenol and By-products of Its Synthesis; Availability of... peer review the Draft Report on Carcinogens (RoC) Monographs for ortho-Toluidine and Pentachlorophenol... monographs are available at http://ntp.niehs.nih.gov/go/38853 . Public Comments Submissions: Deadline is...

The economics of particulate pollution abatement technologies for wood-waste-fired combustors

International Nuclear Information System (INIS)

Ismail, A.; Stevenson, D.H.

1991-07-01

A study was conducted to quantify the impact of new and improved particulate abatement equipment (PAE) on the economics of new and existing wood waste combustion systems. The operating characteristics of current PAE technology are summarized and the basis for cost estimates is established. The technologies include multicyclone collectors, wet scrubbers, fabric filter baghouses, electrostatic precipitators, and new versus retrofit installations. Capital costs were determined for 4 generic types of PAE and 4 cases for each PAE type according to GJ/h in steam enthalpy. Cost information was developed for wood waste energy systems with and without PAE. In the cost analysis, a hypothetical steam selling price is determined which will give a 25% return on pretax cash flow over a 20-year period. Additional costs of the PAE are applied to the energy system cash flows and the impact on average annual return is calculated. Results indicate reductions in internal rate of return of 3-6% for most PAE systems. 54 refs., 2 figs., 12 tabs

Complete knock down (CKD) house made of wood from waste biomass and plastic for disaster struck areas

International Nuclear Information System (INIS)

Foong, Winson

2010-01-01

Despite global efforts and all good intentions to save our forests and eco systems, Mother Earth has witnessed the destruction of some 160,000 square kilometers of forest cover every year from the 1960s right up to the 1990s. The insatiable appetite and unrelenting demand for this fast diminishing commodity by both Mankind and Industry have created vast demand and supply imbalances and with pressures mounting even in the new millennium with global wood consumption reaching 3.8 billion cubic metres by 2010. Thus the quest for alternate materials continues. However, to be successful as a viable alternate to the traditional wood industry, the intending material must be able to build and expand on the current properties and advantages of wood. It should ideally be designed and engineered to yield performance properties superior to that of traditional wood. Fibersit is a high performance fiber composite derived from a revolutionary green technology. The proprietary Fibersit technology involves a method of refining, blending and compounding natural fibers from cellulose waste streams to form a high strength fibre composite material in a polymer matrix. The designated waste or base raw materials used in this instance are those of waste thermoplastics and various categories of cellulose waste including wood. Fibersit has all the structural qualities of wood, handles like wood but is yet stronger and more durable than wood. It can be nailed, screwed, drilled, sawn, milled, processed and finished just like wood. This extended product performance offers unbeatable value for money and broad, flexible on site options. In modern times, many natural disasters have occurred near or in urban areas destroying vast areas of houses and buildings. The need to rebuild society is essential and needs to be carried out in a sustainable manner. This cost often goes into billions and is needed very quickly in order to provide the bare minimum to the victims. In many instances, we have seen

78 FR 51733 - Draft Report on Carcinogens Monographs for ortho-Toluidine and Pentachlorophenol and By-Products...

Science.gov (United States)

2013-08-21

... Monographs for ortho-Toluidine and Pentachlorophenol and By-Products of Its Synthesis; Availability of... the Draft Report on Carcinogens (RoC) Monographs for ortho-Toluidine and Pentachlorophenol and By..., approximately 11:30 a.m. Document Availability: Draft monographs will be available by August 28, 2013, at http...

Mechanical properties of wood from Pinus sylvestris L. treated with Light Organic Solvent Preservative and with waterborne Copper Azole

Energy Technology Data Exchange (ETDEWEB)

Villasante, A.; Laina, R.; Rojas, J. A. M.; Rojas, I. M.; Vignote, S.

2013-07-01

Aim of study: To determine the effect on wood from Pinus sylvestris of treatment with preservatives on mechanical properties and to establish the relation between the penetration and compression strenght. Area of study: Spain. Material and methods: 40 samples of defect-free wood from Pinus sylvestris L. were treated with Light Organic Solvent Preservative (Vacsol Azure WR 2601) and 50 with waterborne Copper Azole (Tanalith E 3492). 40 control samples were not treated (water or preservative). Mechanical resistance to static bending, modulus of elasticity and compression strength parallel to the grain were compared with untreated wood. Regression analysis between the penetration and compression strength parallel was done with the samples treated with waterborne preservative. Main results: The results indicate that the treated wood (with either product) presents a statistically significant increase in mechanical resistance in all three mechanical characteristics. The results obtained differ from earlier studies carried out by other authors. There was no correlation between parallel compression strength and the degree of impregnation of the wood with waterborne Copper Azole. The most probable explanation for these results concerns changes in pressure during treatment. The use of untreated control samples instead of samples treated only with water is more likely to produce significant results in the mechanical resistance studies. Research highlights: Treated wood presents a statistically significant increase in MOE, modulus of rupture to static bending and parallel compression strength. There was no correlation between parallel compression strength and the degree of impregnation with waterborne preservative. (Author)

Statistical analysis of influence of soil source on leaching of arsenic and copper from CCA-C treated wood

Science.gov (United States)

Patricia Lebow; Richard Ziobro; Linda Sites; Tor Schultz; David Pettry; Darrel Nicholas; Stan Lebow; Pascal Kamdem; Roger Fox; Douglas Crawford

2006-01-01

Leaching of wood preservatives affects the long-term efficacy and environmental impact of treated wood. Soil properties and wood characteristicscan affectleaching of woad preservatives, but these effects are not well understood. This paper reports a statistical analysis of the effects of soil and wood properties on leaching of arsenic (As) and copper (Cu) from southern...

Mechanical properties of wood from Pinus sylvestris L. treated with Light Organic Solvent Preservative and with waterborne Copper Azole

Directory of Open Access Journals (Sweden)

A.M. Villasante

2013-12-01

Full Text Available Aim of study: To determine the effect on wood from Pinus sylvestris of treatment with preservatives on mechanical properties and to establish the relation between the penetration and compression strength.Area of study: SpainMaterial and Methods: 40 samples of defect-free wood from Pinus sylvestris L. were treated with Light Organic Solvent Preservative (Vacsol Azure WR 2601 and 50 with waterborne Copper Azole (Tanalith E 3492. 40 control samples were not treated (water or preservative. Mechanical resistance to static bending, modulus of elasticity and compression strength parallel to the grain were compared with untreated wood. Regression analysis between the penetration and compression strength parallel was done with the samples treated with waterborne preservative.Main results: The results indicate that the treated wood (with either product presents a statistically significant increase in mechanical resistance in all three mechanical characteristics. The results obtained differ from earlier studies carried out by other authors.There was no correlation between parallel compression strength and the degree of impregnation of the wood with waterborne Copper Azole . The most probable explanation for these results concerns changes in pressure during treatment.The use of untreated control samples instead of samples treated only with water is more likely to produce significant results in the mechanical resistance studies.Research highlights: Treated wood presents a statistically significant increase in MOE, modulus of rupture to static bending  and parallel compression strength.There was no correlation between parallel compression strength and the degree of impregnation with waterborne preservative.Keywords: Light Organic Solvent Preservative; MOE; parallel compression; static bending; waterborne Copper Azole; wood technology.

Assessment of the radiation field from radioactive elements in a wood-ash-treated coniferous forest in southwest Sweden

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

1996-01-01

The distribution of natural and antrophogenic radioactive elements in soil and wood was investigated in a 30-year-old forest stand of Norway spruce. Forest plots treated with a single dose of granulated wood ash in 1989 were compared with untreated control plots. It was observed that the retention of radiocesium and radiostrontium by the forest soil is rather strong in spite of the high annual precipitation (1100 mm a -1 ) and the relatively acidic conditions of the soil. Most of the deposited nuclear weapon fall-out of radiocesium and radiostrontium is still residing in the forest soil. Radiostrontium, but not radiocesium, was found in the intrasoil water collected with lysimeters at soil depths of 20 and 50 cm. Wood xylem radial distributions of radiostrontium indicated a decreased bioavailability with time after deposition of nuclear weapons fall-out, and no major differences could be observed on comparison of wood from ash-treated plots with wood from untreated plots. The activity concentration of radiocesium in tree rings formed prior to 1986 and grown at the ash-treated plot was about two to three times that found in wood from the untreated control plot. (author)

Preparation of TiO2 photocatalyst with the matrix of palm wood ( Arenga pinnata ) waste in the photodegradation of batik wastewater

International Nuclear Information System (INIS)

Kresnadipayana, Dian; Wahyuni, Endang Tri; Santosa, Sri Juari; Mudasir

2017-01-01

The study aimed to the preparation of TiO 2 photocatalyst with the matrix from palm wood waste whose has lignin and cellulose content. TiO 2 photocatalyst with the matrix from the wastewater of palm wood waste (TiO 2 /pww) was used as photocatalyst in photodegradation of batik wastewater. TiO 2 solid was dissolved in ethanol and aquadest, added with the powder of wood palm waste and stirred with a magnetic stirrer for 16 hours. Then separation was carried out using buchner and filtrate and residue were obtained. The filtrate was disposed and the residue was calcined with various temperatures for 3 hours. The temperatures in this research were 100 °C (TiO 2 /pww-100); 200°C (TiO 2 /pww-200); 300°C (TiO 2 /pww-300). Analysis and characterization of TiO 2 /wwp were conducted using X-ray diffraction (XRD) and spectrophotometer Fourier Transform Infra Red (FTIR) methods. Photocalalytic TiO 2 /wwp use the batch system in a reactor with UV light 40 watts, 220 volts and length wave 360 nm the plate magnetic stirrer. Liquid waste batik adds TiO 2 /wwp with time variation. At XRD analysis showed that the preparation of TiO 2 /pww could be done on the heating TiO 2 /pww temperature of 100°C and 200°C. At the temperature of 300°C, it was indicated that the lignocelluloses in palm wood waste were burned, meaning that few lignocelluloses remained. The result of FTIR analysis showed clearly that at the temperature of 300°C, a few spectrum of lignocelluloses remained in palm wood waste, while at a temperature of 100°C and 200°C, spectra of lignocelluloses of palm wood waste remained. The result of photocatalysis test indicated that TiO 2 /pww could reduce 40%, 72%, 81% and 64% COD for TiO 2 (control), TiO 2 /pww-100, TiO 2 /pww-200 and TiO 2 /pww-300, respectively. (paper)

Immobilization of pentachlorophenol in soil using carbonaceous material amendments

Energy Technology Data Exchange (ETDEWEB)

Wen Bei [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China)], E-mail: bwen@rcees.ac.cn; Li Ruijuan; Zhang Shuzhen [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China); Shan Xiaoquan [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China)], E-mail: xiaoquan@rcees.ac.cn; Fang Jing; Xiao Ke [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Shuangqing Road, Haidian District, Beijing 100085 (China); Khan, Shahamat U. [Department of Chemistry and Biochemistry, MSN 3E2, George Mason University, 4400 University Drive, Fairfax, VA 22030-4444 (United States)

2009-03-15

In this study, three pentachlorophenol (PCP) laboratory-spiked and one field-contaminated soil were amended with 2.0% char, humic acid (HA) and peat, respectively. The amended soils were aged for either 7 or 250 days. After amendment, CaCl{sub 2} extractability of PCP was significantly decreased. Desorption kinetics indicated that the proposed amendment could lead to a strong binding and slow desorption of PCP in soils. Amendment with char reduced the bioaccumulation factor (BAF) of PCP most significantly for earthworms (Eisenia fetida) in all soils studied. The results of both physicochemical and biological tests suggested that amendment reduced PCP bioavailability quickly and enduringly, implying that carbonaceous material amendment, especially char amendment, was a potentially attractive in situ remediation method for sequestration of PCP in contaminated soil. - Carbonaceous material amendment was a potential in situ remediation method for pentachlorophenol contaminated soil.

Effect of natural ageing on volume stability of MSW and wood waste incineration residues

International Nuclear Information System (INIS)

Gori, Manuela; Bergfeldt, Britta; Reichelt, Jürgen; Sirini, Piero

2013-01-01

Highlights: ► Natural weathering on BA from MSW and wood waste incineration was evaluated. ► Type of mineral phases, pH and volume stability were considered. ► Weathering reactions effect in improved stability of the materials. - Abstract: This paper presents the results of a study on the effect of natural weathering on volume stability of bottom ash (BA) from municipal solid waste (MSW) and wood waste incineration. BA samples were taken at different steps of treatment (fresh, 4 weeks and 12 weeks aged) and then characterised for their chemical and mineralogical composition and for volume stability by means of the mineralogical test method (M HMVA-StB), which is part of the German quality control system for using aggregates in road construction (TL Gestein-StB 04). Changes of mineralogical composition with the proceeding of the weathering treatment were also monitored by leaching tests. At the end of the 12 weeks of treatment, almost all the considered samples resulted to be usable without restrictions in road construction with reference to the test parameter volume stability

Pentachlorophenol reduction in raw Cauca river water through activated carbon adsorption in water purification

OpenAIRE

Camilo Hernán Cruz Vélez; Magally González; Héctor Mario Gutiérrez; Luz Edith Barba; Juan Carlos Escobar; Luis Germán Delgado; Patricia Torres

2008-01-01

Reducing chemical risk in raw water from the River Cauca (caused by the presence of pentachlorophenol and organic matter (real color, UV254 absorbance)) was evaluated at bench scale by using three treatment sequences: adsorption with powdered ac-tivated coal (PAC); adsorption – coagulation; and, adsorption – disinfection – coagulation. The results showed that although PAC is appropriate for pentachlorophenol removal, and its use together with the coagulant (aluminium sulphate) significantly i...

Regulatory Promotion of Waste Wood Reused as an Energy Source and the Environmental Concerns about Ash Residue in the Industrial Sector of Taiwan

Directory of Open Access Journals (Sweden)

Wen-Tien Tsai

2012-11-01

Full Text Available The objective of this paper was to provide a preliminary analysis of the utilization of energy derived from waste wood in Taiwan, a highly industrialized country with a high dependence (over 99% on imported energy. The discussion focuses on the status of waste wood generation and its management over the past decade. Findings show that the quantities of biomass waste collected for reuse purposes in the industrial sectors of Taiwan has exhibited an increasing trend, from about 4000 tons in 2001 to over 52,000 tons in 2010. Although waste wood can be reused as a fuel and raw material for a variety of applications based on regulatory promotion, the most commonly used end use is to directly utilize it as an auxiliary fuel in industrial utilities (e.g., boilers, heaters and furnaces for the purpose of co-firing with coal/fuel oil. The most progressive measure for promoting biomass-to-power is to introduce the feed-in tariff (FIT mechanism according to the Renewable Energy Development Act passed in June 2009. The financial support for biomass power generation has been increasing over the years from 0.070 US$/kWh in 2010 to 0.094 US$/kWh in 2012. On the other hand, the environmental regulations in Taiwan regarding the hazard identification of wood-combusted ash (especially in filter fly-ash and its options for disposal and utilization are further discussed in the paper, suggesting that waste wood impregnated with chromated copper arsenate (CCA and other copper-based preservatives should be excluded from the wood-to-energy system. Finally, some recommendations for promoting wood-to-energy in the near future of Taiwan are addressed.

Pentachlorophenol measurements in body fluids of people in log homes and workplaces

Energy Technology Data Exchange (ETDEWEB)

Cline, R.E.; Hill, R.H. Jr.; Phillips, D.L.; Needham, L.L.

1989-07-01

Human exposure to pentachlorophenol (PCP) was evaluated in the normal population (controls), residents of PCP-treated log homes, and persons exposed primarily in the workplace. Blood and urine samples were analyzed by gas chromatography after extraction and acetylation. For 34 controls, serum PCP values ranged from 15-75 ppb with a mean of 40 ppb. For 123 residents of log homes, serum levels ranged from 69-1,340 ppb with a mean of 420 ppb. In such homes, serum levels for children were significantly higher than those for parents, averaging 1.8 times greater. Serum and urine values for workers varied widely, depending on the workplace, with serum levels ranging from 26 to 84,900 ppb of PCP. Urinary concentrations when corrected for creatinine values correlated well (r = 0.92) with serum concentrations. Coating PCP-treated logs of home interiors with a sealant reduced serum PCP levels in the residents.

Effect of simulated rainfall and weathering on release of preservative elements from CCA treated wood

Science.gov (United States)

Stan Lebow; R. Sam Williams; Patricia Lebow

2003-01-01

The release of arsenic from wood pressure-treated with chromated copper arsenate (CCA) can be decreased by application of wood finishes, but little is known about the types of finishes that are best suited for this purpose. This study evaluated the effects of finish water repellent content and ultraviolet (UV) radiation on the release of arsenic, copper, and chromium...

Synchrotron based x-ray fluorescence microscopy confirms copper in the corrosion products of metals in contact with treated wood

Science.gov (United States)

Samuel L. Zelinka; Joseph E. Jakes; Grant T. Kirker; David Vine; Stefan Vogt

2017-01-01

Copper based waterborne wood preservatives are frequently used to extend the service life of wood products when subjected to frequent moisture exposure. While these copper based treatments protect the wood from fungal decay and insect attack, they increase the corrosion of metals embedded or in contact with the treated wood. Previous research has shown the most...

Biotechnology for in vitro growing of edible and medicinal mushrooms on wood wastes

Directory of Open Access Journals (Sweden)

Marian Petre

2009-11-01

Full Text Available The aim of this work was focused on finding out the best way to convert the wood wastes into useful food supplements, such as mushroom fruit bodies, by using them as growing sources for the edible and medicinal mushrooms. According to this purpose, three fungal species from Basidiomycetes, namely Ganoderma lucidum (Curt.:Fr. P. Karst, Lentinus edodes (Berkeley Pegler and Pleurotus ostreatus (Jacquin ex Fries Kummer were tested to determine their biological potential to grow on substrates made of wood wastes (sawdusts as well as shavings which could be used in this way as main ingredients for preparation of natural culture composts.The experiments were achieved by in vitro growing of all these fungal species in special rooms, where the main culture parameters were kept at optimal levels in order to get the highest production of mushroom fruit bodies. The effects of culture compost composition (carbon, nitrogen and mineral sources as well as other physical and chemical factors (such as: temperature, inoculum amount, pH level and incubation time, etc. on mycelial net formation and especially on fruit body induction, were investigated. From all these fungal species tested in our experiments, P. ostreatus was registered as the fastest mushroom culture, then L. edodes and finally, G. lucidum asthe longest mushroom culture. During the experiments, different logs of the same species were used as control samples for each culture compost variants. Applying such biotechnology, the environmental problems generated by the plant wastes accumulation in wood industry could be solved only by using biological means for theirvalorising, simultaneously with food supplements producing having high nutritive values as well as healing effects by increasing the consumers` health.

Biotechnology for in vitro growing of edible and medicinal mushrooms on wood wastes

Directory of Open Access Journals (Sweden)

Marian Petre

2009-12-01

Full Text Available The aim of this work was focused on finding out the best way to convert the wood wastes into useful food supplements, such as mushroom fruit bodies, by using them as growing sources for the edible and medicinal mushrooms. According to this purpose, three fungal species from Basidiomycetes, namely Ganoderma lucidum (Curt.:Fr. P. Karst, Lentinus edodes (Berkeley Pegler and Pleurotus ostreatus (Jacquin ex Fries Kummer were tested to determine their biological potential to grow on substrates made of wood wastes (sawdusts as well as shavings which could be used in this way as main ingredients for preparation of natural culture composts. The experiments were achieved by in vitro growing of all these fungal species in special rooms, where the main culture parameters were kept at optimal levels in order to get the highest production of mushroom fruit bodies. The effects of culture compost composition (carbon, nitrogen and mineral sources as well as other physical and chemical factors (such as: temperature, inoculum amount, pH level and incubation time, etc. on mycelial net formation and especially on fruit body induction, were investigated. From all these fungal species tested in our experiments, P. ostreatus was registered as the fastest mushroom culture, then L. edodes and finally, G. lucidum as the longest mushroom culture. During the experiments, different logs of the same species were used as control samples for each culture compost variants. Applying such biotechnology, the environmental problems generated by the plant wastes accumulation in wood industry could be solved only by using biological means for their valorising, simultaneously with food supplements producing having high nutritive values as well as healing effects by increasing the consumers` health.

Copper Leaching from Copper-ethanolamine Treated Wood: Comparison of Field Test Studies and Laboratory Standard Procedures

OpenAIRE

Nejc Thaler; Miha Humar

2014-01-01

Copper-based compounds are some of the most important biocides for the protection of wood in heavy duty applications. In the past, copper was combined with chromium compounds to reduce copper leaching, but a recent generation of copper-based preservatives uses ethanolamine as a fixative. To elucidate the leaching of copper biocides from wood, Norway spruce (Picea abies) wood was treated with a commercial copper-ethanolamine solution with two different copper concentrations (cCu = 0.125% and 0...

Phytoremediation potential of maize (Zea mays L.) in co-contaminated soils with pentachlorophenol and cadmium.

Science.gov (United States)

Hechmi, Nejla; Ben Aissa, Nadhira; Abdennaceur, Hassen; Jedidi, Naceur

2013-01-01

The ubiquitous coexistence of heavy metals and organic contaminants was increased in the polluted soil and phytoremediation as a remedial technology and management option is recommended to solve the problems of co-contamination. Growth of Zea mays L and pollutant removal ability may be influenced by interactions among mixed pollutants. Pot-culture experiments were conduced to investigate the single and interactive effect of cadmium (Cd) and pentachlorophenol (PCP) on growth of Zea mays L, PCP, and Cd removal from soil. Growth response of Zea mays L is considerably influenced by interaction of Cd and PCP, significantly declining with either Cd or PCP additions. The dissipation of PCP in soils was notably affected by interactions of Cd, PCP, and plant presence or absence. At the Pentachlorophenol in both planted and non-planted soil was greatly decreased at the end of the 10-week culture, accounting for 16-20% of initial extractable concentrations in non-planted soil and 9-14% in planted soil. With the increment of Cd level, residual pentachlorophenol in the planted soil tended to increase. The pentachlorophenol residual in the presence of high concentration of Cd was even higher in the planted soil than that in the non-planted soil.

Switzerland's largest wood-pellet factory in Balsthal

International Nuclear Information System (INIS)

Stohler, F.

2004-01-01

This article describes how a small Swiss electricity utility has broken out of its traditional role in power generation and the distribution of electricity and gone into the production of wood pellets. The pellets, which are made from waste wood (sawdust) available from wood processing companies, are produced on a large scale in one of Europe's largest pellets production facilities. The boom in the use of wood pellets for heating purposes is discussed. The article discusses this unusual approach for a Swiss power utility, which also operates a wood-fired power station and is even involved in an incineration plant for household wastes. The markets being aimed for in Switzerland and in Europe are described, including modern low-energy-consumption housing projects. A further project is described that is to use waste wood available from a large wood processing facility planned in the utility's own region

Potassium methyl siliconate-treated pulp fibers and their effects on wood plastic composites: Water sorption and dimensional stability

Science.gov (United States)

Cheng Piao; Zhiyong Cai; Nicole M. Stark; Charles J. Monlezun

2013-01-01

Potassium methyl siliconate (PMS) was investigated as a new nano modifier of wood fiber and wood flour to improve the compatibility between the fiber/flour and the plastic matrix in fiber reinforced plastic composites. Before injection molding, bleached and brown pulp fibers and mixed species wood flour were pretreated in PMS solutions. The morphology of the treated...

In vitro bioaccessibility of copper azole following simulated dermal transfer from pressure-treated wood

Data.gov (United States)

U.S. Environmental Protection Agency — In vitro bioaccessibility of copper azole following simulated dermal transfer from pressure-treated wood. This dataset is associated with the following publication:...

Nondestructive methods of evaluating quality of wood in preservative-treated piles

Science.gov (United States)

Xiping. Wang; Robert J. Ross; John R. Erickson; John W. Forsman; Gary D. McGinnis; Rodney C. De Groot

2000-01-01

Stress-wave-based nondestructive evaluation methods were used to evaluate the potential quality and modulus of elasticity (MOE) of wood in used preservative-treated Douglas-fir and southern pine piles. Stress wave measurements were conducted on each pile section. Stress wave propagation speeds in the piles were then obtained to estimate their MOE. This was followed by...

Waste treatment of ships. Change in understanding of wastes and trend of waste treatment systems; Senjo no haikibutsu shori. 1. Haikibutsu ni taisuru ninshiki no henka to shori hoshiki no doko

Energy Technology Data Exchange (ETDEWEB)

Inatomi, M. [Hitachi Zosen Corp., Osaka (Japan)

1996-07-25

This paper explains treatment of wastes produced in ships. Wastes produced in ships should be essentially treated on ships. Since storage and transport of difficult-to-treat wastes to harbor for land treatment is expensive, wastes produced in ships are treated on ships as much as possible. Combustibles such as waste oil, plastics, paper and wood fiber waste are treated by incinerator. Food waste is dumped into the sea after crushing by disposer. Excrement and urine are dumped into the sea through a waste water treatment plant. Oil content in oily bilge is burned after heating and vapor separation. Food waste is temporarily stored in ships because its dumping along the coast and into harbor is impossible. Kitchen refuse decomposer utilizing bacteria was proposed for ships. Press for used cans and crushing/thermal compaction/storage equipment for plastics were also put on the market. The primary regulation on diesel engine exhaust gas may be cleared by improvement of engine bodies. 1 ref., 1 fig., 1 tab.

Soil quality in a cropland soil treated with wood ash containing charcoal

Science.gov (United States)

Omil, Beatriz; Balboa, Miguel A.; Fonturbel, M. Teresa; Gartzia-Bengoetxea, Nahia; Arias-González, Ander; Vega, Jose A.; Merino, Agustin

2014-05-01

The strategy of the European Union "Europe 2020" states that by 2020, 20% of final energy consumption must come from renewables. In this scenario, there is an increasing use of biomass utilization for energy production. Indeed, it is expected that the production of wood-ash will increase in coming years. Wood ash, a mixture of ash and charcoal, generated as a by-product of biomass combustion in power plants, can be applied to soil to improve the soil quality and crop production. Since the residue contains significant content of charcoal, the application of mixed wood ash may also improve the SOM content and soil quality in the long term, in soils degraded as a consequence of intensive management. The objective of this study was asses the changes in SOM quality and soil properties in a degraded soils treated with wood ash containing charcoal. The study was carried out in a field devoted to cereal crops during the last decades. The soil was acidic (pH 4.5) with a low SOC content (3 %) and fine texture. The experiment was based on a randomised block design with four replicates. Each block included the following four treatments: Control, 16 Mg fly wood ash ha-1, 16 Mg mixed wood ash ha-1 (16 Mg) and 32 Mg mixed wood ash ha-1 (32 Mg). The application was carried out once. The ash used in the study was obtained from a thermal power plant and was mainly derived from the combustion of Pinus radiata bark and branches. The wood ash is highly alkaline (pH= 10), contains 10 % of highly condensed black carbon (atomic H/C ratio solid state 13C CPMAS NMR and Differential Scanning Calorimetry (DSC). These techniques were applied in bulk samples and aggregates of different sizes. The changes in microbial activity were studied by analysis of microbial biomass C and basal respiration. The soil bacterial community was studied by the Biolog method. Several physical properties, such soil aggregate distribution, hydraulic conductivity and available water contente were also determined

Modelling inorganic and organic biocide leaching from CBA-amine (Copper–Boron–Azole) treated wood based on characterisation leaching tests

Energy Technology Data Exchange (ETDEWEB)

Lupsea, Maria [University of Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F–31077 Toulouse (France); INRA, UMR 792, F-31400 Toulouse (France); CNRS, UMR 5504, F-31400 Toulouse (France); Paris-Est University, CSTB — Scientific and Technical Centre for the Building Industry, DEE/Environment and Life Cycle Engineering Team, 24 Rue Joseph Fourier, F-38400 Saint Martin d' Hères (France); Tiruta-Barna, Ligia, E-mail: ligia.barna@insa-toulouse.fr [University of Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F–31077 Toulouse (France); INRA, UMR 792, F-31400 Toulouse (France); CNRS, UMR 5504, F-31400 Toulouse (France); Schiopu, Nicoleta [Paris-Est University, CSTB — Scientific and Technical Centre for the Building Industry, DEE/Environment and Life Cycle Engineering Team, 24 Rue Joseph Fourier, F-38400 Saint Martin d' Hères (France); Schoknecht, Ute [BAM — Federal Institute for Materials Research and Testing, Division 4.1, Unter den Eichen 87, 12205 Berlin (Germany)

2013-09-01

Numerical simulation of the leaching behaviour of treated wood is the most pertinent and less expensive method for the prediction of biocides' release in water. Few studies based on mechanistic leaching models have been carried out so far. In this work, a coupled chemistry-mass transport model is developed for simulating the leaching behaviour of inorganic (Cu, B) and organic (Tebuconazole) biocides from CBA-amine treated wood. The model is based on experimental investigations (lab-scale leaching tests coupled with chemical and structural analysis). It considers biocides' interactions with wood solid components and with extractives (literature confirmed reactions), as well as transport mechanisms (diffusion, convection) in different compartments. Simulation results helped at identifying the main fixation mechanisms, like (i) direct complexation of Cu by wood-phenolic and -carboxylic sites (and not via monoethanolamine; complex) on lignin and hemicellulose and strong dependence on extractives' nature, (ii) pH dependent binding of tebuconazole on polarized -OH moieties on wood. The role of monoethanolamine is to provide a pore-solution pH of about 7.5, when copper solubility is found to be weakest. The capability of the developed model to simulate the chemical and transport behaviour is the main result of this study. Moreover, it proved that characterization leaching tests (pH dependency and dynamic tests), combined with appropriate analytical methods are useful experimental tools. Due to its flexibility for representing and simulating various leaching conditions, chemical-transport model developed could be used to further simulate the leaching behaviour of CBA treated wood at larger scales. - Highlights: • Biocide and extractives leaching from ammonia-CBA treated wood were modelled. • The chemical-transport model identifies the main fixation/solubilisation mechanisms. • The model describes well the results of equilibrium and dynamic leaching

Design and testing of wood containers for radioactive waste

International Nuclear Information System (INIS)

Roberts, R.S.; Barry, P.E.

1981-01-01

A wood container for shipping and storing radioactive waste was designed to eliminate the problems caused by the weight, cost, and shape of the steel containers previously used. Tests specified by federal regulations (compression, free-drop, penetration, and vibration) were conducted on two of the containers, one loaded to 2500 lb and one loaded to 5000 lb. The 5000-lb container failed the free-drop test, but the 2500-lb container easily passed the tests and therefore qualifies as a Type A container. Its simplicity of design, low weight, and ease in handling have proved to be time-saving and cost-effective

Improving the two-step remediation process for CCA-treated wood. Part I, Evaluating oxalic acid extraction

Science.gov (United States)

Carol Clausen

2004-01-01

In this study, three possible improvements to a remediation process for chromated-copper-arsenate (CCA) treated wood were evaluated. The process involves two steps: oxalic acid extraction of wood fiber followed by bacterial culture with Bacillus licheniformis CC01. The three potential improvements to the oxalic acid extraction step were (1) reusing oxalic acid for...

Effect of precipitation pattern on leaching of preservative from treated wood and implications for accelerated testing

Science.gov (United States)

Stan Lebow

2014-01-01

There is a need to develop improved accelerated test methods for evaluating the leaching of wood preservatives from treated wood exposed to precipitation. In this study the effects of rate of rainfall and length of intervals between rainfall events on leaching was evaluated by exposing specimens to varying patterns of simulated rainfall under controlled laboratory...

Use of handheld X-ray fluorescence spectrometry units for identification of arsenic in treated wood

Energy Technology Data Exchange (ETDEWEB)

Block, Colleen N. [University of Miami, Department of Civil, Architectural, and Environmental Engineering, P.O. Box 248294, McArthur Building, Coral Gables, FL 33124-0630 (United States); Shibata, Tomoyuki [University of Miami, Department of Civil, Architectural, and Environmental Engineering, P.O. Box 248294, McArthur Building, Coral Gables, FL 33124-0630 (United States); Solo-Gabriele, Helena M. [University of Miami, Department of Civil, Architectural, and Environmental Engineering, P.O. Box 248294, McArthur Building, Coral Gables, FL 33124-0630 (United States)]. E-mail: hmsolo@miami.edu; Townsend, Timothy G. [University of Florida, Department of Environmental Engineering Sciences, Gainesville, FL 32611-6450 (United States)

2007-07-15

The objective of this study was to evaluate the performance of handheld XRF analyzers on wood that has been treated with a preservative containing arsenic. Experiments were designed to evaluate precision, detection limit, effective depth of analysis, and accuracy of the XRF arsenic readings. Results showed that the precision of the XRF improved with increased sample concentration and longer analysis times. Reported detection limits decreased with longer analysis times to values of less than 1 mg/kg or 18 mg/kg, depending on the model used. The effective depth of analysis was within the top 1.2 cm and 2.0 cm of sample for wood containing natural gradients of chemical preservative and concentration extremes, respectively. XRF results were found to be 1.5-2.3 times higher than measurements from traditional laboratory analysis. Equations can be developed to convert XRF values to results which are consistent with traditional laboratory testing. - Handheld XRF analyzers provided quantitative results for the amount of arsenic within preservative-treated wood.

Climate protection potential in the waste management sector. Examples: municipal waste and waste wood; Klimaschutzpotenziale der Abfallwirtschaft. Am Beispiel von Siedlungsabfaellen und Altholz

Energy Technology Data Exchange (ETDEWEB)

Dehoust, Guenter; Schueler, Doris [Oeko-Institut e.V. Institut fuer angewandte Oekologie, Darmstadt (Germany); Vogt, Regine; Giegrich, Juergen [IFEU Institut fuer Energie- und Umweltforschung Heidelberg GmbH (Germany)

2010-03-15

In the National Inventory Reports only the direct greenhouse gas emissions of the waste management sector are taken into account. The overall efforts of the waste management sector in terms of reducing greenhouse gas emissions in accordance with the Kyoto Protocol are not, therefore, represented. In particular the efforts related to the separate collection of recyclables from waste and the re-use or energetic use of such recyclables or residue are shown as the savings of other sectors of the production industry and energy industry. This research project has used the methodology of eco-balancing to examine the efforts of the municipal waste management sector - including the use of waste wood - in Germany, the 27 Member States as well as in Turkey, Tunisia and Mexico. The balances referred to the actual balance in 2006 and different optimisation scenarios for 2020. The expenditure resulting from collection, transport, treatment and recycling of waste after it has become available was compared to the savings arising from the secondary products and energy realised from waste. Since the landfilling of untreated municipal waste has been discontinued in Germany, the key potentials of the country have already been fully tapped. Indeed, the contribution of municipal waste management to the reduction of total greenhouse gas emissions amounted to approx. 18 million t CO{sub 2}-eq per annum in 2006 in Germany. In particular, these emission reductions have been brought about by improving treatment techniques (emission reductions in the biological processes and greater energy efficiency in the thermal processes) and by increases in the separate collection and use of recyclable materials stemming from municipal waste and waste wood. If both strategies are combined, there is still an optimisation potential for reducing greenhouse gas emissions of 10 million t CO{sub 2}-eq per annum. Compared to 1990 data taken from previous assessments, the overall reduction amounts to approx. 56

Online Sorting of Wood Treated with Chromated Copper Arsenate Using Laser Induced Breakdown Spectroscopy

National Research Council Canada - National Science Library

Moskal, Thomas

2001-01-01

.... While CCA treated wood has several benefits, with perhaps the most important being the saving of an estimated 225 million trees annually due to its longer service life, there are growing concerns...

FIRE RESISTANCE OF DOUGLAS FIR [Pseudotsuga menziesii (Mirb. Franco] WOOD TREATED WITH SOME CHEMICALS

Directory of Open Access Journals (Sweden)

M. Kemal YALINKILIÇ

1998-02-01

Full Text Available Combustible properties of treated douglas wood specimens and fire-retardancy of some preservatives were tested in this study. Crib test of ASTM E 160-150 was followed. Results indicated that, aqueous solutions of boric acid (BA, borax (Bx (Na2BO7 10H2O or BA + Bx mixture (7: 3, w: w had fire retardant efficacy (FRE over untreated wood and reduced the combustibility of vinil monomers (Styrene and methylmetacrylate which were applied as secondary treatment.

Effect of weathering on chromated copper arsenate (CCA) treated wood : leaching of metal salts and change in water repellency

Science.gov (United States)

R. Sam Williams; Stan Lebow; Patricia Lebow

2003-01-01

Wood pressure-treated with chromated copper arsenate (CCA) wood preservative is commonly used for outdoor construction. Oxides of arsenic, copper, and chromium are bound in the wood by a complex series of chemical reactions, but a small percentage of these compounds are gradually released by leaching and weathering. Recent studies suggest that the release of these...

The classification of wood chips parameters by crushing of waste cane from different varieties of grapevine

Directory of Open Access Journals (Sweden)

Patrik Burg

2008-01-01

Full Text Available This work deales with exploitatives parameters monitoring of wood shreder PEZZOLATO 110 Mb by crushing of waste cane of six varieties. The results shows that the wood shreders efficiency, fuel consumption and the wood chips elements size can be influenced by varieties characters of cane. The va­lued machines efficiency was 230–470 kg . h−1 by average volume 40.70 % water in wood. The hig­hest values by cane crushing had the variety Saint Laurent (0.47 t . h−1 and the lowest variety ­Blauer Portugieser (0.23 t . h−1. The specific consumption of petrol Natural 95 was 4.52.10−3–8.12.10−3 l . kg−1. The average middle elements lenght was 6.64 mm by crushed varieties.

A wood-waste fuelled, indirectly-fired gas turbine cogeneration plant for sawmill application. Phase 1. Preliminary engineering design and financial evaluation

Energy Technology Data Exchange (ETDEWEB)

1986-02-01

Most sawmills generate more than enough wood waste to be potentially self-sufficient in both dry-kiln heat and electricity requirements. It is not generally economically viable to use conventional steam/electricty cogeneration systems at the sawmill scale of operation. As a result, Canadian sawmills are still large consumers of purchased fuels and electricity. The overall objective of this project was to develop a cost-effective wood waste-fired power generation and lumber drying system for sawmill applications. The system proposed and evaluated in this project is a wood waste-fuelled, indirectly-fired gas turbine cogeneration plant. Research, design, and development of the system has been planned to take place in a number of phases. Phase 1 consists of a preliminary engineering design and financial evaluation of the system, the subjects of this report. The results indicate that the proposed indirectly-fired gas turbine cogeneration system is both technically and financially feasible under a variety of conditions. 8 figs., 8 tabs.

Corrosivity of hot flue gases in the fluidized bed combustion of recovered waste wood

Energy Technology Data Exchange (ETDEWEB)

Enestam, S.

2011-07-01

In recent years, recovered waste wood has become a fuel of interest due to its green energy benefits and low price compared to virgin wood-based fuels. However, waste wood is often contaminated with paint, plastic, and metal components, producing concentrations of heavy metals such as zinc and lead, chlorine, sodium, and sometimes sulphur that are elevated relative to those in virgin wood. In several cases, boilers burning waste wood have experienced increased fouling and corrosion of furnace walls, superheaters, and economizers, problems associated with chlorine, zinc, lead, and alkali metals in the deposits. The location of the deposits and the corrosion as well as the composition of the deposits vary with the fuel composition, boiler design, combustion parameters, flue gas temperature, and material temperature. Experience gained from the operation of biofuel and waste boilers shows that corrosion damage can be reduced, or even avoided, by the selection of optimum materials or for heat exchanger surfaces, by the use of fuel mixtures or additives that decrease the corrosivity of the combustion environment, by the placement of superheaters in a less corrosive environment, and by adjusting the steam parameters. Finding the right solutions for boilers burning RWW requires a thorough understanding of the whole process, including the fuel fed into the boiler, the combustion atmosphere, the corrosivity of the flue gas and the deposits, and the corrosion resistance of different boiler materials under the prevailing conditions. The objective of this work was to shed more light on the combustion environment in bubbling fluidized bed boilers burning RWW and thus increase knowledge about the corrosivity of zinc- and lead-rich deposits formed during the combustion of RWW, with the final goal of developing a corrosion prediction tool for use in the design of boilers for RWW combustion. With such a tool, it would be possible to optimize boiler design and material selection with

Morphology, composition, and mixing state of primary particles from combustion sources ? crop residue, wood, and solid waste

OpenAIRE

Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A. P.; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye

2017-01-01

Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combusti...

New Approach to Remove Metals from Chromated Copper Arsenate (CCA)-Treated Wood

Science.gov (United States)

Todd F. Shupe; Chung Y. Hse; Hui Pan

2012-01-01

Recovery of metals from chromated copper arsenate (CCA)-treated southern pine wood particles was investigated using binary acid solutions consisting of acetic, oxalic, and phosphoric acids in a microwave reactor. Formation of an insoluble copper oxalate complex in the binary solution containing oxalic acid was the major factor for low copper removal. Furthermore, the...

Pentachlorophenol from an old henhouse as a dioxin source in eggs and related human exposure

International Nuclear Information System (INIS)

Piskorska-Pliszczynska, Jadwiga; Strucinski, Pawel; Mikolajczyk, Szczepan; Maszewski, Sebastian; Rachubik, Jaroslaw; Pajurek, Marek

2016-01-01

High levels of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were detected in free-range eggs, and these levels reached a concentration of 29.84 ± 7.45 pg of WHO-TEQ/g of fat. This value exceeded the EU maximum permitted level of 2.5 pg of WHO-TEQ/g of fat for PCDD/F congeners by twelve-fold. A chemical analysis (HRGC-HRMS) revealed elevated amounts of OCDD, OCDF, HxCDD, HpCDD and HpCDF. During the investigation, samples of feed, soil, wall scrapings, wooden ceiling of the henhouse and tissues from laying hens were examined for dioxin contents (30 samples altogether). The long and complicated investigation found that the source of dioxins in the poultry farm was pentachlorophenol-treated wood, which was used as structural components in the 40-year-old farm building adapted to a henhouse. The wooden building material contained PCDD/Fs at a concentration of 3922.60 ± 560.93 pg of WHO-TEQ/g and 11.0 ± 2.8 μg/kg of PCP. The potential risk associated with dioxin intake was characterized by comparing the theoretically calculated weekly and monthly intakes with the toxicological reference values (TRVs), namely the Tolerable Weekly Intake (TWI) and Provisional Tolerable Monthly Intake (PTMI) values of 14 pg of WHO-TEQ/kg of bw and 70 pg of WHO-TEQ/kg of bw, respectively. The intake of dioxins estimated for high egg consumers (approximately 5–6 eggs/week) exceeded the TWI and PTMI values, which may pose a risk of delayed adverse health effects. The estimated dose of PCDD/Fs and DL-PCBs for children consuming 5 eggs per week exceeded the TWI by as much as 450% because of their nearly 5-fold-lower body weight. Although the dioxin intake estimated for the average consumption of eggs in the general population did not exceed any of the TRVs applied (58.7% TWI and 51.1% PTMI), such a situation should be considered unacceptable from a public health perspective because eggs are not the only source of these contaminants

Inventories of woody residues and solid wood waste in the United States, 2002

Science.gov (United States)

David B. McKeever

2004-01-01

Large amounts of woody residues and wood waste are generated annually in the United States. In 2002, an estimated 240 million metric tons was generated during the extraction of timber from the Nation’s forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in...

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

Energy Technology Data Exchange (ETDEWEB)

Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

2014-12-15

Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine

Chemically treated carbon black waste and its potential applications

Energy Technology Data Exchange (ETDEWEB)

Dong, Pengwei; Maneerung, Thawatchai; Ng, Wei Cheng; Zhen, Xu [NUS Environmental Research Institute, National University of Singapore, 1 Create Way, Create Tower #15-02, 138602 (Singapore); Dai, Yanjun [School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Tong, Yen Wah [NUS Environmental Research Institute, National University of Singapore, 1 Create Way, Create Tower #15-02, 138602 (Singapore); Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Ting, Yen-Peng [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Koh, Shin Nuo [Sembcorp Industries Ltd., 30 Hill Street #05-04, 179360 (Singapore); Wang, Chi-Hwa, E-mail: chewch@nus.edu.sg [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore); Neoh, Koon Gee, E-mail: chenkg@nus.edu.sg [Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585 (Singapore)

2017-01-05

Highlights: • Hazardous impurities separated from carbon black waste with little damage to solid. • Heavy metals were effectively removed from carbon black waste by HNO{sub 3} leaching. • Treated carbon black waste has high adsorption capacity (∼356.4 mg{sub dye}/g). • Carbon black waste was also found to show high electrical conductivity (10 S/cm). - Abstract: In this work, carbon black waste – a hazardous solid residue generated from gasification of crude oil bottom in refineries – was successfully used for making an absorbent material. However, since the carbon black waste also contains significant amounts of heavy metals (especially nickel and vanadium), chemical leaching was first used to remove these hazardous impurities from the carbon black waste. Acid leaching with nitric acid was found to be a very effective method for removal of both nickel and vanadium from the carbon black waste (i.e. up to 95% nickel and 98% vanadium were removed via treatment with 2 M nitric acid for 1 h at 20 °C), whereas alkali leaching by using NaOH under the same condition was not effective for removal of nickel (less than 10% nickel was removed). Human lung cells (MRC-5) were then used to investigate the toxicity of the carbon black waste before and after leaching. Cell viability analysis showed that the leachate from the original carbon black waste has very high toxicity, whereas the leachate from the treated samples has no significant toxicity. Finally, the efficacy of the carbon black waste treated with HNO{sub 3} as an absorbent for dye removal was investigated. This treated carbon black waste has high adsorption capacity (∼361.2 mg {sub dye}/g {sub carbonblack}), which can be attributed to its high specific surface area (∼559 m{sup 2}/g). The treated carbon black waste with its high adsorption capacity and lack of cytotoxicity is a promising adsorbent material. Moreover, the carbon black waste was found to show high electrical conductivity (ca. 10 S

Corrosion rates of fasteners in treated wood exposed to 100% relative humidity

Science.gov (United States)

Samuel L. Zelinka; Douglas R. Rammer

2009-01-01

In the past, gravimetric corrosion data for fasteners exposed to treated wood has been reported as a percent weight loss. Although percent weight loss is a valid measure of corrosion for comparing identical fasteners, it can distort the corrosion performance of fasteners with different geometries and densities. This report reevaluates a key report on the corrosiveness...

Treating water-reactive wastes

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Some compounds and elements, such as lithium hydride, magnesium, sodium, and calcium react violently with water to generate much heat and produce hydrogen. The hydrogen can ignite or even form an explosive mixture with air. Other metals may react rapidly only if they are finely divided. Some of the waste produced at Los Alamos National Laboratory includes these metals that are contaminated with radioactivity. By far the greatest volume of water-reactive waste is lithium hydride contaminated with depleted uranium. Reactivity of the water-reactive wastes is neutralized with an atmosphere of humid nitrogen, which prevents the formation of an explosive mixture of hydrogen and air. When we adjust the temperature of the nitrogen and the humidifier, the nitrogen can be more or less humid, and the rate of reaction can be adjusted and controlled. Los Alamos has investigated the rates of reaction of lithium hydride as a function of the temperature and humidity, and, as anticipated, they in with in temperature and humidity. Los Alamos will investigate other variables. For example, the nitrogen flow will be optimized to conserve nitrogen and yet keep the reaction rates high. Reaction rates will be determined for various forms of lithium waste, from small chips to powder. Bench work will lead to the design of a skid-mounted process for treating wastes. Other water-reactive wastes will also be investigated

Overview of established and emerging treatment technologies for polycyclic aromatic hydrocarbons at wood preserving facilities

International Nuclear Information System (INIS)

Shearon, M.D.

1992-01-01

The contamination of soil and groundwater by polycyclic aromatic hydrocarbons (PAHs) is common to wood preserving facilities and manufactured gas plants. Since the inception of RCRA and CERCLA, much attention has been focused upon the remediation of both active and defunct wood preserving facilities. The experiences gleaned from the use of proven technologies, and more importantly, the lessons being learned in the trials of emerging technologies on creosote-derived PAH clean-ups at wood preserving sites, should have direct bearing on the clean-up of similar contaminants at MGP sites. In this paper, a review of several remedial actions using waste removal/disposal, on-site incineration, and bioremediation will be presented. Additionally, emerging technologies for the treatment of PAH-contaminated soil and water will be reviewed. Lastly, recent information on risk assessment results for creosote sites and treated PAH waste will be discussed

Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

Energy Technology Data Exchange (ETDEWEB)

Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

2007-03-15

At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

Extraction of Pentachlorophenol from Soils using Environmentally Benign Lactic Acid Solutions

Science.gov (United States)

Soil contamination with pentachlorophenol (PCP) is widespread across the globe. Soil washing/extraction is a common technique to remove this compound. Several soil washing/extraction solutions have been used but a majority of them have the problem of persistence in the environmen...

Woody residues and solid waste wood available for recovery in the United States, 2002

Science.gov (United States)

David B. McKeever; Robert H. Falk

2004-01-01

Large amounts of woody residues and solid wood waste are generated annually in the United States from the extraction of timber from forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in the construction and demolition of buildings and structures, and in the...

SOLID-PHASE TREATMENT OF A PENTACHLOROPHENOL- CONTAMINATED SOIL USING LIGNIN-DEGRADING FUNGI

Science.gov (United States)

The abilities of three lignin-degrading fungi, Phanerochaete chrysosporium, Phanerochaete sordida, and Trametes hirsuta, to deplete pentachlorophenol (PCP) from soil contaminated with PCP and creosote were evaluated. A total of seven fungal and three control treatments ...

Recognized and new problems of power generation from waste wood according to the new EEG of 2004; Alte und neue Probleme der Altholzverstromung nach der EEG-Novelle 2004

Energy Technology Data Exchange (ETDEWEB)

Anger, C. [Avocado Rechtsanwaelte, Koeln (Germany)

2005-10-01

Power generation from waste wood according to the EEG (Renewables Act), even in the modified version of 2004, raises complex legal problems under EU law. The contribution discusses these problems and presents important information on the legal boundary conditions of power generation from waste wood. (orig.)

Wood chemistry symposium: from muka to lignin

Energy Technology Data Exchange (ETDEWEB)

MacLeod, M.

1979-01-01

The Canadian Wood Chemistry Symposium held during September, 1979, is reviewed. The chemical and physical explanations of delignification were debated. Problems of mechanical pulping include insufficient brightness, yellowing, and low strength relative to energy consumption. A session on chemicals, energy, and food from wood began with criteria for a viable project, which included adequate return on investment, modest capital investment requirements, identified pre-existing markets, and favorable thermodynamic balances. The pulp and paper industry should improve its methods of using bark and wood waste in direct combustion (by pre-drying wastes and improving furnace efficiency) rather than supporting oil-from-wood projects, since using a waste for fuel will free fossil fuels for uses in synthetic fibers and thermoplastics. In the area of food, there are modest successes with cellulose fiber additives to bread and snack food and single cell protein (which, though made from wastes, cannot compete with soy protein). However, making monomeric sugars from wood polysaccharides is not an efficient process, and muka, animal feed supplement from foliage, is successful only in Russia. In Canada it cannot compete with agricultural products. Alpha cellulose is a major wood chemical product. Promising uses include cellulose derived thermoplastics and lignosulphonates for secondary oil recovery. Instead of breaking wood polysaccharides and lignin into monomers and then repolymerizing them, it is possible to use the pre-built polymers; such an approach is illustrated by use of lignin in polyurethane foams, adhesives, and coatings.

Environmentally friendly wood preservatives formulated with enzymatic-hydrolyzed okara, copper and/or boron salts

International Nuclear Information System (INIS)

Ahn, Sye Hee; Oh, Sei Chang; Choi, In-gyu; Han, Gyu-seong; Jeong, Han-seob; Kim, Ki-woo; Yoon, Young-ho; Yang, In

2010-01-01

Novel biocides, such as copper azole (CuAz) and ammoniacal copper quaternary (ACQ), are extensively used as substitutes for chromate copper arsenate (CCA) in wood preservation. However, the expense of these biocides has necessitated the development of cost-effective and environmentally friendly wood preservatives. This study was conducted to investigate the effectiveness against decaying fungi of the preservatives formulated with enzymatic-hydrolyzed okara (OK), which is an organic waste produced from the manufacture of tofu, CuCl 2 (CC) and/or Na 2 B 4 O 7 .10H 2 O (B). With the addition of NH 4 OH as a dissociating agent, the addition of OK facilitated the target retention of most of the OK/CC and OK/CC/B preservative formulations in wood blocks. The OK-based wood preservatives (OK-WPs) were stable against hot-water leaching. When compared with control and CC-treated wood blocks, the leached wood blocks treated with OK/CC and OK/CC/B formulations showed excellent decay resistance against both Postia placenta and Gloeophyllum trabeum, especially when OK was hydrolyzed by Celluclast at a loading level of 0.1 ml/g. Scanning electron microscopy (SEM) and SEM-energy dispersive X-ray (SEM-EDX) spectrometry analyses demonstrated that preservative complexes, such as OK-CC and OK-CC-B, existed in the wood blocks treated with OK/CC and OK/CC/B formulations. This study results support the potential application of OK-WPs as environmentally friendly wood preservatives capable of replacing CuAz and ACQ.

Environmentally friendly wood preservatives formulated with enzymatic-hydrolyzed okara, copper and/or boron salts

Energy Technology Data Exchange (ETDEWEB)

Ahn, Sye Hee; Oh, Sei Chang [Department of Forest Resources, Daegu University, Gyeongsan 712-714 (Korea, Republic of); Choi, In-gyu [Department of Forest Sciences, Seoul National University, Seoul 151-921 (Korea, Republic of); Han, Gyu-seong [Department of Wood and Paper Sciences, Chungbuk National University, Cheongju 361-763 (Korea, Republic of); Jeong, Han-seob [Department of Forest Sciences, Seoul National University, Seoul 151-921 (Korea, Republic of); Kim, Ki-woo [National Instrumentation Center for Environmental Management, Seoul National University, Seoul 151-921 (Korea, Republic of); Yoon, Young-ho [KCI Co. Ltd., Seosan, Chungcheongnam-do 356-874 (Korea, Republic of); Yang, In, E-mail: dahadad2000@yahoo.com [Research Institute for Agriculture and Life Sciences, Seoul National University, San 56-1 Sillim-Dong, Kwanak-gu, Seoul 151-921 (Korea, Republic of)

2010-06-15

Novel biocides, such as copper azole (CuAz) and ammoniacal copper quaternary (ACQ), are extensively used as substitutes for chromate copper arsenate (CCA) in wood preservation. However, the expense of these biocides has necessitated the development of cost-effective and environmentally friendly wood preservatives. This study was conducted to investigate the effectiveness against decaying fungi of the preservatives formulated with enzymatic-hydrolyzed okara (OK), which is an organic waste produced from the manufacture of tofu, CuCl{sub 2} (CC) and/or Na{sub 2}B{sub 4}O{sub 7}.10H{sub 2}O (B). With the addition of NH{sub 4}OH as a dissociating agent, the addition of OK facilitated the target retention of most of the OK/CC and OK/CC/B preservative formulations in wood blocks. The OK-based wood preservatives (OK-WPs) were stable against hot-water leaching. When compared with control and CC-treated wood blocks, the leached wood blocks treated with OK/CC and OK/CC/B formulations showed excellent decay resistance against both Postia placenta and Gloeophyllum trabeum, especially when OK was hydrolyzed by Celluclast at a loading level of 0.1 ml/g. Scanning electron microscopy (SEM) and SEM-energy dispersive X-ray (SEM-EDX) spectrometry analyses demonstrated that preservative complexes, such as OK-CC and OK-CC-B, existed in the wood blocks treated with OK/CC and OK/CC/B formulations. This study results support the potential application of OK-WPs as environmentally friendly wood preservatives capable of replacing CuAz and ACQ.

Arsenic levels in wipe samples collected from play structures constructed with CCA-treated wood: Impact on exposure estimates

Energy Technology Data Exchange (ETDEWEB)

Barraj, Leila M. [Chemical Regulation and Food Safety, Exponent, Inc., Suite 1100, 1150 Connecticut Ave., NW, Washington, DC 20036 (United States)], E-mail: lbarraj@exponent.com; Scrafford, Carolyn G. [Chemical Regulation and Food Safety, Exponent, Inc., Suite 1100, 1150 Connecticut Ave., NW, Washington, DC 20036 (United States); Eaton, W. Cary [RTI International, 3040 Cornwallis Road, Research Triangle Park, NC 27709 (United States); Rogers, Robert E.; Jeng, Chwen-Jyh [Toxcon Health Sciences Research Centre Inc., 9607 - 41 Avenue, Edmonton, Alberta, T6E 5X7 (Canada)

2009-04-01

Lumber treated with chromated copper arsenate (CCA) has been used in residential outdoor wood structures and playgrounds. The U.S. EPA has conducted a probabilistic assessment of children's exposure to arsenic from CCA-treated structures using the Stochastic Human Exposure and Dose Simulation model for the wood preservative scenario (SHEDS-Wood). The EPA assessment relied on data from an experimental study using adult volunteers and designed to measure arsenic in maximum hand and wipe loadings. Analyses using arsenic handloading data from a study of children playing on CCA-treated play structures in Edmonton, Canada, indicate that the maximum handloading values significantly overestimate the exposure that occurs during actual play. The objective of our paper is to assess whether the dislodgeable arsenic residues from structures in the Edmonton study are comparable to those observed in other studies and whether they support the conclusion that the values derived by EPA using modeled maximum loading values overestimate hand exposures. We compared dislodgeable arsenic residue data from structures in the playgrounds in the Edmonton study to levels observed in studies used in EPA's assessment. Our analysis showed that the dislodgeable arsenic levels in the Edmonton playground structures are similar to those in the studies used by EPA. Hence, the exposure estimates derived using the handloading data from children playing on CCA-treated structures are more representative of children's actual exposures than the overestimates derived by EPA using modeled maximum values. Handloading data from children playing on CCA-treated structures should be used to reduce the uncertainty of modeled estimates derived using the SHEDS-Wood model.

Wood

DEFF Research Database (Denmark)

Unterrainer, Walter

2014-01-01

come from? How is it harvested? How is it manufactured and treated ? How are the buildings detailed and protected against weather during construction to keep them dry and make them long-life ? In a period of climate change, forests are the last lungs of the planet to sequestrate CO2. Their global size......Wood – a sustainable building material ? For thousands of years and all over the planet, wood has been used as a building material and exciting architecture has been created in wood. The fantastic structural, physical and aesthetic properties of the material as well as the fact that wood...

Effect of pH and inoculum size on pentachlorophenol degradation ...

African Journals Online (AJOL)

The success of this depends on finding strains able to degrade PCP in a changeable environment. The aim of this work was to study the influence of pH of the medium and the effect of inoculum size on pentachlorophenol degradation by Pseudomonas sp. A study of PCP degradation kinetics was performed to assess such ...

Analysis of preservative-treated wood by multivariate analysis of laser-induced breakdown spectroscopy spectra

International Nuclear Information System (INIS)

Martin, Madhavi Z.; Labbe, Nicole; Rials, Timothy G.; Wullschleger, Stan D.

2005-01-01

In this work, multivariate statistical analysis (MVA) techniques are coupled with laser-induced breakdown spectroscopy (LIBS) to identify preservative types (chromated copper arsenate, ammoniacal copper zinc or alkaline copper quat), and to predict elemental content in preservative-treated wood. The elemental composition of the samples was measured with a standard laboratory method of digestion followed by atomic absorption spectroscopy analysis. The elemental composition was then correlated with the LIBS spectra using projection to latent structures (PLS) models. The correlations for the different elements introduced by different treatments were very strong, with the correlation coefficients generally above 0.9. Additionally, principal component analysis (PCA) was used to differentiate the samples treated with different preservative formulations. The research has focused not only on demonstrating the application of LIBS as a tool for use in the forest products industry, but also considered sampling errors, limits of detection, reproducibility, and accuracy of measurements as they relate to multivariate analysis of this complex wood substrate

Analysis of preservative-treated wood by multivariate analysis of laser-induced breakdown spectroscopy spectra

Energy Technology Data Exchange (ETDEWEB)

Martin, Madhavi Z. [Environmental Sciences Division Oak Ridge National Laboratory, P.O. Box 2008 MS 6422, Oak Ridge TN 37831-6422 (United States); Labbe, Nicole [Forest Products Center, University of Tennessee, 2506 Jacob Drive, Knoxville, TN 37996-4570 (United States)]. E-mail: nlabbe@utk.edu; Rials, Timothy G. [Forest Products Center, University of Tennessee, 2506 Jacob Drive, Knoxville, TN 37996-4570 (United States); Wullschleger, Stan D. [Environmental Sciences Division Oak Ridge National Laboratory, P.O. Box 2008 MS 6422, Oak Ridge TN 37831-6422 (United States)

2005-08-31

In this work, multivariate statistical analysis (MVA) techniques are coupled with laser-induced breakdown spectroscopy (LIBS) to identify preservative types (chromated copper arsenate, ammoniacal copper zinc or alkaline copper quat), and to predict elemental content in preservative-treated wood. The elemental composition of the samples was measured with a standard laboratory method of digestion followed by atomic absorption spectroscopy analysis. The elemental composition was then correlated with the LIBS spectra using projection to latent structures (PLS) models. The correlations for the different elements introduced by different treatments were very strong, with the correlation coefficients generally above 0.9. Additionally, principal component analysis (PCA) was used to differentiate the samples treated with different preservative formulations. The research has focused not only on demonstrating the application of LIBS as a tool for use in the forest products industry, but also considered sampling errors, limits of detection, reproducibility, and accuracy of measurements as they relate to multivariate analysis of this complex wood substrate.

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

Science.gov (United States)

Saqib, Naeem; Bäckström, Mattias

2014-12-01

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

Coupling effect of waste automotive engine oil in the preparation of wood reinforced LDPE plastic composites for panels

Directory of Open Access Journals (Sweden)

Maame Adwoa Bentumah Animpong

2017-12-01

Full Text Available We demonstrated the formulation of wood plastic composite (WPC materials with flexural strength of 13.69 ± 0.09 MPa for applications in outdoor fencing using municipal waste precursors like low density polyethylene (LDPE plastics (54.0 wt. %, sawn wood dust with particle size between 64 and 500 μm derived from variable hardwood species (36.0 wt. % and used automotive engine oil (10 wt. %. The WPC panels were prepared by pre-compounding, extruding at a screw auger torque of 79.8 Nm and pressing through a rectangular mould of dimension 132 mm × 37 mm × 5 mm at temperature 150 °C. The efficacy of black waste oil, as a coupling agent, was demonstrated by the absence of voids and pull-outs on microscopic examination using scanning electron microscopy. No hazardous substances were exhaled during thermo-gravimetric mass spectrometry analysis. The percentage crystallinity of the LDPE in the as-prepared material determined by differential scanning calorimetry was 11.3%. Keywords: Wood plastic composites, Low density polyethylene, Wood dust, Physical, Thermal and mechanical properties

Process for treating waste water having low concentrations of metallic contaminants

Science.gov (United States)

Looney, Brian B; Millings, Margaret R; Nichols, Ralph L; Payne, William L

2014-12-16

A process for treating waste water having a low level of metallic contaminants by reducing the toxicity level of metallic contaminants to an acceptable level and subsequently discharging the treated waste water into the environment without removing the treated contaminants.

Technologies for the commercial energetic utilisation of waste wood and used wood; Technologien zur energetischen Nutzung von Holzabfaellen und Gebrauchsholz im gewerblichen Bereich

Energy Technology Data Exchange (ETDEWEB)

Marutzky, R.

1998-12-31

Due to the frequent contamination of wood with wood preservatives, coatings, adhesives, paints and other non-wood materials the conversion of production residues and various types of used wood to energy appears to be fraught with problems. However, extensive studies conducted during the past years have shown that most problems regarding combustion residues and emissions have been overestimated. Thanks to new technologies it is now possible to avoid or at least reduce the formation of pollutants during combustion of even complexly contaminated waste wood. Environmentally acceptable combustion of wood presupposes complete combustion, effective dedusting, and primary measures for nitrogen oxide control. Depending on the type of feedstock and the relevant emission limit values one may optionally include secondary nitric oxides removal measures and control techniques for partially volatile heavy metals and halocarbons. Moreover, firing plants must be so conditioned as to keep the new synthesis of dioxins at a low level. [Deutsch] Die energetische Verwertung von Produktionsabfaellen und Gebrauchtholzsortimenten scheint wegen der haeufig vorhandenen Belastung der Hoelzer mit Holzschutzmitteln, Oberflaechenbeschichtungen, Klebstoffen, Farbanstrichen und andere holzfremden Bestandteilen schwierig zu sein. Tatsaechlich sind - wie umfangreiche Untersuchungen der letzten Jahre gezeigt haben - die meisten Probleme in Hinblick auf Ausbrand und Emissionen ueberschaetzt worden. Durch Weiterentwicklung von Anlagen- und Regelungstechnik ist es heute moeglich, die Schadstoffbildung bei der Verbrennung auch komplex belasteter Holzabfaelle zu vermeiden oder zu vermindern. Voraussetzungen einer umweltvertraeglichen Verbrennung von Holz sind - ein guter Ausbrand, - eine effektive Entstaubung, - und primaere Massnahmen der Stickstoffoxidminderung. Optional kommen je nach Brennstoff und Emissionsgrenzwert noch sekundaere Entstickungsmassnahmen und Minderungstechniken fuer partiell

Wood wastes and residues generated along the Colorado Front Range as a potential fuel source

Science.gov (United States)

Julie E. Ward; Kurt H. Mackes; Dennis L. Lynch

2004-01-01

Throughout the United States there is interest in utilizing renewable fuel sources as an alternative to coal and nat-ural gas. This project was initiated to determine the availability of wood wastes and residues for use as fuel in ce-ment kilns and power plants located along the Colorado Front Range. Research was conducted through literature searches, phone surveys,...

Waste Management: DOD Has Generally Addressed Legislative Requirements on the Use of Burn Pits but Needs to Fully Assess Health Effects

Science.gov (United States)

2016-09-01

such as tires , treated wood, and batteries) in burn pits during contingency operations. GAO found that DOD’s report fully addressed four of the seven...regulations prohibiting the disposal of covered waste (including certain types of hazardous waste, medical waste, and items such as tires , treated...required contractors to segregate non-hazardous, hazardous, and recyclable materials; establish recycling systems; and maintain all solid waste operations

Environmental assessment of the atlas bio-energy waste wood fluidized bed gasification power plant. Final report

Energy Technology Data Exchange (ETDEWEB)

Holzman, M.I.

1995-08-01

The Atlas Bio-Energy Corporation is proposing to develop and operate a 3 MW power plant in Brooklyn, New York that will produce electricity by gasification of waste wood and combustion of the produced low-Btu gas in a conventional package steam boiler coupled to a steam-electric generator. The objectives of this project were to assist Atlas in addressing the environmental permit requirements for the proposed power plant and to evaluate the environmental and economic impacts of the project compared to more conventional small power plants. The project`s goal was to help promote the commercialization of biomass gasification as an environmentally acceptable and economically attractive alternative to conventional wood combustion. The specific components of this research included: (1) Development of a permitting strategy plan; (2) Characterization of New York City waste wood; (3) Characterization of fluidized bed gasifier/boiler emissions; (4) Performance of an environmental impact analysis; (5) Preparation of an economic evaluation; and (6) Discussion of operational and maintenance concerns. The project is being performed in two phases. Phase I, which is the subject of this report, involves the environmental permitting and environmental/economic assessment of the project. Pending NYSERDA participation, Phase II will include development and implementation of a demonstration program to evaluate the environmental and economic impacts of the full-scale gasification project.

Wood fuel and the environment

International Nuclear Information System (INIS)

Foster, C.A.

1992-01-01

The purpose of this paper is to try and demonstrate the role that the use of Wood as a Fuel can play in our environment. The term ''Wood Fuel'', for the purposes of these proceedings, refers to the use of wood obtained from the forest or the farm. It does not refer to waste wood from for example buildings. The role of wood fuel in the environment can be assessed at many different levels. In this paper three different scales of ''Environment'' and the role of wood fuel in each, will be considered. These three scales are namely the global environment, the local environment, and the National (community) environment. (Author)

Mechanics of Wood Machining

CERN Document Server

Csanády, Etele

2013-01-01

Wood is one of the most valuable materials for mankind, and since our earliest days wood materials have been widely used. Today we have modern woodworking machine and tools; however, the raw wood materials available are continuously declining. Therefore we are forced to use this precious material more economically, reducing waste wherever possible. This new textbook on the “Mechanics of Wood Machining” combines the quantitative, mathematical analysis of the mechanisms of wood processing with practical recommendations and solutions. Bringing together materials from many sources, the book contains new theoretical and experimental approaches and offers a clear and systematic overview of the theory of wood cutting, thermal loading in wood-cutting tools, dynamic behaviour of tool and work piece, optimum choice of operational parameters and energy consumption, the wear process of the tools, and the general regularities of wood surface roughness. Diagrams are provided for the quick estimation of various process ...

Phosphate removal by refined aspen wood fiber treated with carboxymethyl cellulose and ferrous chloride

Science.gov (United States)

Thomas L. Eberhardt; Soo-Hong Min; James S. Han

2006-01-01

Biomass-based filtration media are of interest as an economical means to remove pollutants and nutrients found in stormwater runoff. Refined aspen wood fiber samples treated with iron salt solutions demonstrated limited capacities to remove (ortho)phosphate from test solutions. To provide additional sites for iron complex formation, and thereby impart a greater...

Determination of Cu, Cr, and As in preserved wood (Eucalyptus sp.) using x-ray fluorescent spectrometry techniques

International Nuclear Information System (INIS)

Sergio Matias Pereira Junior; Vera Akiko Maihara; Edson Goncalves Moreira; Vera Lucia Ribeiro Salvador; Ivone Mulako Sato

2016-01-01

Energy dispersive (EDXRF) and Portable (PXRF) X-ray fluorescence techniques are proposed for wood treatment control process and wood waste assortment. In this study, different retentions of chromated copper arsenate preservative were applied to Eucalyptus sp. sapwood samples. Cu, Cr and As were determined by XRF techniques in treated sapwood massive blocks and treated sapwood sawdust samples were analyzed by FAAS spectrometry (Flame Atomic Absorption) and INAA (Instrumental Neutron Activation Analysis). Cu, Cr and As mean values, obtained by FAASS and INAA, showed to be statically equal; however, XRF analysis showed considerable deviations, presenting the absorption and the enhancement effects in analytical lines. (author)

Wood preservative testing

Science.gov (United States)

Rebecca Ibach; Stan T. Lebow

2012-01-01

Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

Pine Wood Treated with a Citric Acid and Glycerol Mixture: Biomaterial Performance Improved by a Bio-byproduct

Directory of Open Access Journals (Sweden)

Gatien Geraud Essoua Essoua

2016-02-01

Full Text Available Wood material is a good reservoir for biogenic carbon storage. The use of wood material for outdoor products such as siding in the building construction sector presents limits. These limits are bound to the nature of wood material (hygroscopic property and anatomical structure. They are responsible for the dimensional variation associated with moisture content variations. Fungal attacks and coating layers adhesion on wood surface, are other problems. This research investigated the feasibility of impregnation with environmentally friendly chemicals, i.e., a citric acid-glycerol mixture (CA-G. The anti-swelling efficiency (ASE, hardness, biodegradation, and coating adhesion tests were performed on softwood specimens. ASE results were up to 53%. The equilibrium moisture content of the treated specimens was less than half of the untreated ones. FTIR spectroscopy showed bands at 1720 to 1750 cm-1, indicating the presence of ester bonds, and scanning electron microscopy images confirmed the polymerization and condensation of treatment solution inside the wood structure. Hardness and decay resistance were increased; however, treatment reduces coating adhesion. In conclusion, CA-G represents a promising eco-responsible solution for improving the technical performance of outdoor wood products.

Controlled composting of waste wood contaminated with PAH; Untersuchungen zur gesteuerten Rotte von mit polyzyklischen aromatischen Kohlenwasserstoffen (PAK) kontaminiertem Altholz

Energy Technology Data Exchange (ETDEWEB)

Ulbricht, H.

2002-07-01

The author investigated the potential and limits of microbial pollutant degradation in PAH-polluted waste wood by composting. The conditions in which autochthonic micro-organisms are able to decomposite the PAH contained in wood by solid phase fermentation were investigated. The focus was on phenanthrene, anthracene and pyrene, all of which are used as protective materials (disinfestants) for wood. The results were verified on contaminated waste wood, including an analytical investigations of decomposition of PAH of the EPA catalogue. Boundary conditions for achieving high rates of PAH decomposition were investigated. [German] Generelles Ziel der Arbeit war die Untersuchung der Moeglichkeiten und Grenzen des mikrobiellen Schadstoffabbaus in PAK-belastetem Altholz durch Kompostierung und die Pruefung auf Anwendbarkeit der Erkenntnisse in technischen Verfahren. In der vorliegenden Arbeit wurde untersucht, unter welchen Bedingungen die autochthonen Mikroorganismen in der Lage sind, an das Holz gebundene PAK durch Feststofffermentation abzubauen. Als Schwerpunkt wurde zunaechst der Abbau der im zum Holzschutz verwendetem Teeroel vorkommenden PAK Phenanthren, Anthracen und Pyren untersucht. Eine Verifizierung der Ergebnisse erfolgte mit real kontaminiertem Altholz, dabei wurde der Abbau der PAK der EPA-Liste analytisch verfolgt. Es sollten geeignete Randbedingungen gefunden werden, um im Festphasensystem hohe Abbauraten der PAK zu erreichen. (orig.)

A process for treating radioactive water-reactive wastes

International Nuclear Information System (INIS)

Dziewinski, J.; Lussiez, G.; Munger, D.

1995-01-01

Los Alamos National Laboratory and other locations in the complex of experimental and production facilities operated by the United States Department of Energy (DOE) have generated an appreciable quantity of hazardous and radioactive wastes. The Resource Conservation and Recovery Act (RCRA) enacted by the United States Congress in 1976 and subsequently amended in 1984, 1986, and 1988 requires that every hazardous waste must be rendered nonhazardous before disposal. Many of the wastes generated by the DOE complex are both hazardous and radioactive. These wastes, called mixed wastes, require applying appropriate regulations for radioactive waste disposal and the regulations under RCRA. Mixed wastes must be treated to remove the hazardous waste component before they are disposed as radioactive waste. This paper discusses the development of a treatment process for mixed wastes that exhibit the reactive hazardous characteristic. Specifically, these wastes react readily and violently with water. Wastes such as lithium hydride (LiH), sodium metal, and potassium metal are the primary wastes in this category

Mechanical and natural durability properties of wood treated with a novel organic preservative/consolidant product

International Nuclear Information System (INIS)

Lionetto, Francesca; Frigione, Mariaenrica

2009-01-01

An organic preservative/consolidant of new formulation was selected in order to evaluate its effect on the mechanical properties of worm-eaten walnut wood. Walnut wood is widely used for the realization of artistic handworks (e.g. statues, altars, etc.) furniture and flooring. The flexural strength and modulus of elasticity, the toughness and the hardness were determined on both treated and untreated samples. The experimental results showed that the product increased significantly the flexural strength while the other mechanical properties were not appreciably affected by the chemical treatment. The microstructure of the samples tested was observed using scanning electron microscopy. The preserving character against insects of the investigated product was assessed by both visual inspection and measurements of weight loss on the treated specimens after their exposure to living insects. The samples on which the product was applied, exposed to Oligomerus ptilinoides for one year, were more resistant to decay than the corresponding untreated samples.

Experiments on torrefied wood pellet: study by gasification and characterization for waste biomass to energy applications.

Science.gov (United States)

Rollinson, Andrew N; Williams, Orla

2016-05-01

Samples of torrefied wood pellet produced by low-temperature microwave pyrolysis were tested through a series of experiments relevant to present and near future waste to energy conversion technologies. Operational performance was assessed using a modern small-scale downdraft gasifier. Owing to the pellet's shape and surface hardness, excellent flow characteristics were observed. The torrefied pellet had a high energy density, and although a beneficial property, this highlighted the present inflexibility of downdraft gasifiers in respect of feedstock tolerance due to the inability to contain very high temperatures inside the reactor during operation. Analyses indicated that the torrefaction process had not significantly altered inherent kinetic properties to a great extent; however, both activation energy and pre-exponential factor were slightly higher than virgin biomass from which the pellet was derived. Thermogravimetric analysis-derived reaction kinetics (CO2 gasification), bomb calorimetry, proximate and ultimate analyses, and the Bond Work Index grindability test provided a more comprehensive characterization of the torrefied pellet's suitability as a fuel for gasification and also other combustion applications. It exhibited significant improvements in grindability energy demand and particle size control compared to other non-treated and thermally treated biomass pellets, along with a high calorific value, and excellent resistance to water.

Combustion Characteristics of Impregnated and Surface-treated Chestnut (Castanea sativa Mill. Wood Left Outdoors for One Year

Directory of Open Access Journals (Sweden)

Muhammed Said Fidan

2016-01-01

Full Text Available Treating wood with impregnating materials in order to improve resistance to burning is a commonly employed safety measure. In this study, chestnut (Castanea sativa Mill. wood samples were impregnated using either Tanalith-E or Wolmanit-CB according to ASTM-D 1413-76 and surface-treated using water-based or synthetic varnish according to ASTM-D 3023. These samples were used to investigate the combustion characteristics of samples left outdoors for one year as detailed in ASTM-E 160-50. The combustion temperatures of the samples left outdoors were similar upon impregnation with either Tanalith-E or Wolmanit-CB. However, the combustion temperature of the samples treated with synthetic varnish was lower than those that were treated with water-based varnish. The time to collapse and the total duration of combustion of the samples left outdoors were shorter for those impregnated with Wolmanit-CB. Weight loss of the samples left outdoors was higher for those that were impregnated with Tanalith-E and treated with water-based varnish. Gas analysis of the samples that were left outdoors indicated that the O2 content of flue gas from samples that were impregnated with Wolmanit-CB and treated with synthetic varnish was high and the CO content of flue gas from the same samples was low.

Proposed methods for treating high-level pyrochemical process wastes

International Nuclear Information System (INIS)

Johnson, T.R.; Miller, W.E.; Steunenberg, R.K.

1985-01-01

This survey illustrates the large variety and number of possible techniques available for treating pyrochemical wastes; there are undoubtedly other process types and many variations. The choice of a suitable process is complicated by the uncertainty as to what will be an acceptable waste form in the future for both TRU and non-TRU wastes

Controversy. The wood war

International Nuclear Information System (INIS)

James, O.

2010-01-01

The author comments the conflict emerging in France between industries exploiting wood for construction and those exploiting it as a heating material for power generation. The first ones accuse the others to steal their raw material, to pull the prices up, and to destabilize the sector. This conflict takes place notably around sawmill wastes which are used either by wood panel fabricators or by wood pellets producers. Both sectors are claiming they are creating more jobs than the other. The French forest indeed offers good opportunities for both sectors, but other countries which are lacking forest surfaces, are buying wood in France. Several issues are matter of discussion: burning wood seems to go against the reduction of greenhouse gas emissions, subsidies awarded to big heater projects. The situation of the wood sector in Austria, Finland and Poland is briefly presented

Robust and Low-Cost Flame-Treated Wood for High-Performance Solar Steam Generation.

Science.gov (United States)

Xue, Guobin; Liu, Kang; Chen, Qian; Yang, Peihua; Li, Jia; Ding, Tianpeng; Duan, Jiangjiang; Qi, Bei; Zhou, Jun

2017-05-03

Solar-enabled steam generation has attracted increasing interest in recent years because of its potential applications in power generation, desalination, and wastewater treatment, among others. Recent studies have reported many strategies for promoting the efficiency of steam generation by employing absorbers based on carbon materials or plasmonic metal nanoparticles with well-defined pores. In this work, we report that natural wood can be utilized as an ideal solar absorber after a simple flame treatment. With ultrahigh solar absorbance (∼99%), low thermal conductivity (0.33 W m -1 K -1 ), and good hydrophilicity, the flame-treated wood can localize the solar heating at the evaporation surface and enable a solar-thermal efficiency of ∼72% under a solar intensity of 1 kW m -2 , and it thus represents a renewable, scalable, low-cost, and robust material for solar steam applications.

Landfill disposal of CCA-treated wood with construction and demolition (C&D) debris: arsenic, chromium, and copper concentrations in leachate.

Science.gov (United States)

Jambeck, Jenna R; Townsend, Timothy G; Solo-Gabriele, Helena M

2008-08-01

Although phased out of many residential uses in the United States, the disposal of CCA-treated wood remains a concern because significant quantities have yet to be taken out of service, and it is commonly disposed in landfills. Catastrophic events have also led to the concentrated disposal of CCA-treated wood, often in unlined landfills. The goal of this research was to simulate the complex chemical and biological activity of a construction and demolition (C&D) debris landfill containing a realistic quantity of CCA-treated wood (10% by mass), produce leachate, and then evaluate the arsenic, copper, and chromium concentrations in the leachate as an indication of what may occur in a landfill setting. Copper concentrations were not significantly elevated in the control or experimental simulated landfill setting (alpha = 0.05). However, the concentrations of arsenic and chromium were significantly higher in the experimental simulated landfill leachate compared to the control simulated landfill leachate (alpha = 0.05, p debris can impact leachate quality which, in turn could affect leachate management practices or aquifers below unlined landfills.

Equipment for biomass. Wood burners; Materiels pour la biomasse, les chaudieres bois

Energy Technology Data Exchange (ETDEWEB)

Chieze, B. [SA Compte R., 63 - Arlanc (France)

1997-12-31

A review of the French classification of biomass wastes (and more especially wood and wood wastes) concerning classified burning equipment, is presented: special authorization is thus needed for burning residues from wood second transformation processes. Limits for combustion product emission levels are detailed and their impact on wood burning and process equipment is examined: feeder, combustion chamber, exchanger, fume treatment device, residue disposal. Means for reducing pollutant emissions are reviewed

The incorporation of wood waste ash as a partial cement replacement material for making structural grade concrete: An overview

Directory of Open Access Journals (Sweden)

Swaptik Chowdhury

2015-06-01

Full Text Available With increasing industrialization, the industrial byproducts (wastes are being accumulated to a large extent, leading to environmental and economic concerns related to their disposal (land filling. Wood ash is the residue produced from the incineration of wood and its products (chips, saw dust, bark for power generation or other uses. Cement is an energy extensive industrial commodity and leads to the emission of a vast amount of greenhouse gases, forcing researchers to look for an alternative, such as a sustainable building practice. This paper presents an overview of the work and studies done on the incorporation of wood ash as partial replacement of cement in concrete from the year 1991 to 2012. The aspects of wood ash such as its physical, chemical, mineralogical and elemental characteristics as well as the influence of wood ash on properties such as workability, water absorption, compressive strength, flexural rigidity test, split tensile test, bulk density, chloride permeability, freeze thaw and acid resistance of concrete have been discussed in detail.

Wood Flour Moulding Technology: Implications for Technical ...

African Journals Online (AJOL)

User

2011-04-19

Apr 19, 2011 ... be waste product from saw mills, wood working plants or produced from selected dry wood by .... Stop watch-used to indicate the exact time the mould has remained in the press before wood .... There is abundance of saw dust the source of which is the ... Madison, Wisconsin: Wiley Interscience. Usoro, H. S. ...

Bio-Oil Production from Fast Pyrolysis of Corn Wastes and Eucalyptus Wood in a Fluidized Bed Reactor

Directory of Open Access Journals (Sweden)

M.A Ebrahimi-Nik

2014-09-01

Full Text Available Fast pyrolysis is an attractive technology for biomass conversion, from which bio-oil is the preferred product with a great potential for use in industry and transport. Corn wastes (cob and stover and eucalyptus wood are widely being produced throughout the world. In this study, fast pyrolysis of these two materials were examined under the temperature of 500 °C; career gas flow rate of 660 l h-1; particle size of 1-2 mm; 80 and 110 g h-1 of feed rate. The experiments were carried out in a continuous fluidized bed reactor. Pyrolysis vapor was condensed in 3 cooling traps (15, 0 and -40 °C plus an electrostatic one. Eucalyptus wood was pyrolyised to 12.4, 61.4, and 26.2 percent of bio-char, bio-oil and gas, respectively while these figures were as 20.15, 49.9, and 29.95 for corn wastes. In all experiments, the bio-oil obtained from electrostatic trap was a dark brown and highly viscose liquid.

Process for treating waste water containing hydrazine from power stations

International Nuclear Information System (INIS)

Hoffmann, W.

1982-01-01

A process for treating waste water containing hydrazine from nuclear power stations is proposed, characterized by the fact that the water is taken continuously through a water decomposition cell. If the water does not have sufficient conductivity itself, a substance raising the electrical conductivity is added to the water to be treated. The electrolysis is situated in the waste water tank. (orig./RB) [de

SOLID FUEL OF HYDROCARBON, WOOD AND AGRICULTURAL WASTE FOR LOCAL HEAT SUPPLY SYSTEMS

Directory of Open Access Journals (Sweden)

B. M. Khroustalev

2017-01-01

Full Text Available In Belarus oil refining and oil producing industries are paid close attention. On the background of the active maintaining the level of oil processing and volume of oil extraction in our country and in the countries of the Eurasian Economic Union there is a steady formation of hydrocarbon-containing waste; therefore recycling of the latter is an urgent task to improve the competitiveness of production. The most cost-effective way of using hydrocarbon waste is the conversion of it into power resources. In this case it is possible to obtain significant power-saving and economic effect of the combined use of a hydrocarbon, wood, agricultural and other combustible waste, meanwhile improving the ecological situation at the sites of waste storage and creating a solid fuel with the necessary energy and specified physical-and-chemical properties. A comprehensive solution of a recycling problem makes it possible to use as energy resources a lot of waste that has not found application in other technologies, to produce alternative multi-component fuel which structure meets environmental and energy requirement for local heating systems. In addition, the implementation of such technology will make it possible to reduce power consumption of enterprises of various kinds that consume fuel and will also increase the share of local fuels in the energy balance of a particular region.

Resistance of borax–copper treated wood in aboveground exposure to attack by Formosan subterranean termites

Science.gov (United States)

Stan Lebow; Bessie Woodward; Douglas Crawford; William Abbott

2005-01-01

The spread of Formosan subterranean termites (FSTs) in the southern United States has increased public interest in finding a preservative treatment to protect framing lumber from termite attack. This study evaluated the use of a borax-based preservative to protect wood from FST attack. Southern Pine and Douglas-fir specimens were pressure-treated with three...

Experimental and modelling studies on a laboratory scale anaerobic bioreactor treating mechanically biologically treated municipal solid waste.

Science.gov (United States)

Lakshmikanthan, P; Sughosh, P; White, James; Sivakumar Babu, G L

2017-07-01

The performance of an anaerobic bioreactor in treating mechanically biologically treated municipal solid waste was investigated using experimental and modelling techniques. The key parameters measured during the experimental test period included the gas yield, leachate generation and settlement under applied load. Modelling of the anaerobic bioreactor was carried out using the University of Southampton landfill degradation and transport model. The model was used to simulate the actual gas production and settlement. A sensitivity analysis showed that the most influential model parameters are the monod growth rate and moisture. In this case, pH had no effect on the total gas production and waste settlement, and only a small variation in the gas production was observed when the heat transfer coefficient of waste was varied from 20 to 100 kJ/(m d K) -1 . The anaerobic bioreactor contained 1.9 kg (dry) of mechanically biologically treated waste producing 10 L of landfill gas over 125 days.

Gamma radiation treatment of pentachlorophenol, 2,4-dichlorophenol and 2-chlorophenol in water

International Nuclear Information System (INIS)

He Yongke; Liu Jun; Wu Jilan

2001-01-01

The aim of this work was to investigate γ radiation treatment of pentachlorophenol (PCP), 2,4- dichlorophenol (DCP) and o-chlorophenol (o-CP) in water. The dechlorination of PCP, DCP and o-CP has been studied using γ radiation as well as ozonization. G(CI-) is always much higher than the corresponding G(-PCP),this means that some primary radiolytic products are unstable during post irradiation. PCP is much easier to be decomposed under irradiation than that of simple chlorophenol. Some stable radiolytic intermediates were be detected. Primary analysis reveals some quinones among the final products with toxicity that remains unclear. In the pulse radiolytic experiment, it was determined that about 53% of radicals undergo electrotransfer and others undergo addition when OH radicals react with PCP. The values of COD(Mn) after irradiating PCP in dosage were determined. It is recommended to bubble ozone simultaneously when radiation (or electron beam) treat CPs contaminating water. (author)

CREEP BEHAVIOR OF BORATE-TREATED STRANDBOARD: EFFECT OF ZINC BORATE RETENTION, WOOD SPECIES, AND LOAD LEVEL

OpenAIRE

Wu,Qinglin; Lee,Ong N; Cai,Zhiyong; Zhou,Dingguo

2009-01-01

Creep performance of zinc borate-treated strandboard from southern pine (Pinus taeda L.) and red oak (Quercus falcata) was investigated at 25(0)C temperature and 65% relative humidity. It was shown that the borate treatment had some significant effect on creep deflection of the test panels, and the effect varied with wood species. There was no significant effect of creep loading on residual bending properties of treated strandboard under the stress levels used. The four element spring-dashpot...

Suitability of green solvent in pre treating agricultural waste

International Nuclear Information System (INIS)

Yoon, Li Wan; Ngoh, Gek Cheng; Chua, Adeline Seak May

2010-01-01

Full text: Agricultural wastes such as palm oil residue, rice husk and sugarcane bagasse have been found to occupy the largest fraction in the total biomass generated in Malaysia. These residues are normally lacking of commercial values and have limited alternative uses. Since they are being generated substantially every year, their disposal has caused a serious problem to the society and the environment. Hence, it is essential to discover the potentials of converting these wastes into wealth. One of the major drawbacks which hinder their effective utilization is due to their recalcitrant nature. Thus, pretreatment is necessary in order to disrupt the complex carbohydrate structures in the substrate and improves its digestibility. The present study showed the efficiencies of various mediums namely ionic liquid, acid, alkali and water in pre treating sugarcane bagasse. The performances of these pretreatment mediums were evaluated by the reducing sugar generated after enzymatically hydrolysed the treated substrate. The results obtained were compared with the untreated sugarcane bagasse. In this study, substrate treated by ionic liquid has yielded the highest amount of reducing sugar followed by alkali treated substrate. The performance of untreated bagasse is found to be better than acid and water treated bagasse. These results showed that ionic liquid which has been identified as the green solvent can be an effective medium in pre treating the sugarcane bagasse. This finding has given a new prospect in the production of value added products from agricultural wastes. (author)

Effect of waste rubber powder as filler for plywood application

Directory of Open Access Journals (Sweden)

Ong Huei Ruey

2015-03-01

Full Text Available The study investigated the suitability of waste rubber powder (WRP use as filler in adhesive formulation for plywood application. Melamine Urea Formaldehyde (MUF was employed as resin for formulating the wood adhesive. To improve chemical properties and bonding quality of adhesive, WRP was treated by different chemicals like 20% nitric acid, 30% hydrogen peroxide and acetone solution. The treated WRP were analysed by XRD and it showed that inorganic compounds were removed and carbon was remained as major component under the treatment of 20% HNO3. The treatment improved the mechanical properties like shear strength and formaldehyde emission of plywood (high shear strength and low formaldehyde emission. The physico-chemical interaction between the wood, resin and filler was investigated using fourier transform infrared spectroscopic (FTIR technique and the interactions among N-H of MUF and C=O of wood and WRP were identified. The morphology of wood-adhesive interface was studied by field emission scanning electron microscope (FESEM and light microscope (LM. It showed that the penetration of adhesives and fillers through the wood pores was responsible for mechanical interlocking. Therefore, chemically treated WRP proved its potential use as filler in MUF based adhesive for making plywood.

Method of treating radioactive waste material

International Nuclear Information System (INIS)

Allison, W.

1980-01-01

A method of treating radioactive waste material, particularly a radioactive sludge, is described comprising separating solid material from liquid material, compressing the solid material and encapsulating the solid material in a hardenable composition such as cement, bitumen or a synthetic resin. The separation and compaction stages are conveniently effected in a tube press. (author)

Fast pyrolysis of creosote treated wood ties in a fluidized bed reactor and analytical characterization of product fractions

International Nuclear Information System (INIS)

Jung, Su-Hwa; Koo, Won-Mo; Kim, Joo-Sik

2013-01-01

A fraction of creosote treated wood ties was pyrolyzed in a pyrolysis plant equipped with a fluidized bed reactor and char-separation system at different temperatures. Analyses of each pyrolysis product, especially the oil, were carried out using a variety of analytical tools. The maximum oil yield was obtained at 458 °C with a value of 69.3 wt%. Oils obtained were easily separated into two phases, a creosote-derived fraction (CDF) and a wood-derived fraction (WDF). Major compounds of the WDF were acetic acid, furfural and levoglucosan, while the CDF was mainly composed of polycyclic aromatic hydrocarbons (PAHs), such as 1-methylnaphthalene, biphenyl, acenaphthene, dibenzofuran, fluorene, phenanthrene, anthracene, fluoranthene and pyrene. HPLC analysis showed that the concentration of PAHs of the CDF obtained at 458 °C constituted about 22.5 wt% of the oil. - Highlights: • Creosote treated wood ties was stably pyrolyzed in a fluidized bed reactor. • Pyrolysis oil contained extremely low metal content due to the char removal system. • Bio-oil components was quantitatively analyzed by relative response factor. • Creosote-derived pyrolysis oil fraction was composed of PHAs and has a high caloric value (39 MJ/kg)

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

Science.gov (United States)

Ribera, Javier; Fink, Siegfried; Bas, Maria Del Carmen; Schwarze, Francis W M R

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

Directory of Open Access Journals (Sweden)

Javier Ribera

Full Text Available The production of new generation of wood preservatives (without addition of a co-biocide in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720 was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium. T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%. Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens

Removal of Pentachlorophenol Using Microwave Assisted Persulfate from Synthetic Wastewater

Directory of Open Access Journals (Sweden)

Ghorban Asgari

2014-07-01

Full Text Available Pentachlorophenol (PCP is an important class of environmental pollutants which is excessively used in industry in spite of strong evidence about its hazards. Therefore, the removal of PCP from aqua solution is recommended due to its toxicity and health risks. In the present study, the removal of PCP using a modified domestic microwave (MW oven alone and in combination with persulfate (MW/PS was investigated. The effects of operational parameters such as pH of solution, the power of microwave radiations and the amount of persulfate concentration were studied. A spectrophotometer was used for determining of the concentration of pentachlorophenol. The experimental results showed that the removal of PCP was influenced by many factors, such as the pH value, the amount of persulfate and microwave power. The optimum conditions for the best removal rate were obtained at pH=11, a persulfate concentration of 0.02mol/L and microwave irradiation power of about 600W for MW/PS system at constant PCP concentration.  Also, the direct degradation results showed that the removal of PCP was 2% in MW system without PS after 30 min of MW irradiation. The removal of PCP by MW/PS and MW alone were follow first order rate decay kinetics and the rate constants were 0.093 and 0.00066 min-1, respectively.

Some Exploitation Properties of Wood Plastic Hybrid Composites Based on Polypropylene and Plywood Production Waste

Science.gov (United States)

Kajaks, Janis; Kalnins, Karlis; Uzulis, Sandris; Matvejs, Juris

2015-12-01

During the last 20-30 years many researchers have paid attention to the studies of properties of thewood polymer composites (WPC). A lot of works are closely related to investigations of exploitation properties of wood fibres or wood flour containing polyolefine composites [1, 2]. The most useful from wide selection of polyolefines are polypropylenes, but timber industry waste materials comprising lignocellulose fibres are often used as reinforcement of WPC [3-12]. Plywood industry is not an exception - part of waste materials (by-products) are used for heat energy, i.e. burned. In this work we have approbated reinforcing of polypropylene (PP) with one of the plywood industry by-products, such as birch plywood sawdust (PSWD),which containswood fibre fractions with different length [13]. The main fraction (50%) includes fibres with length l = 0.5 - 1 mm. Our previous study [13] has confirmed that PSWD is a promising filler for PP reinforcing. Addition of PSWD up to 40-50 wt.% has increased WPC tensile and flexural modulus, but decreased deformation ability of PP matrix, impact strength, water resistance and fluidity of composite melts. It was shown [13] that modification of the composites with interfacial modifier - coupling agent maleated polypropylene (MAPP content up to 5-7 wt.%) considerably improved all the abovementioned properties. SEM investigations also confirmed positive action of coupling agent on strengthening of adhesion interaction between components wood and PP matrix. Another way how to make better properties of the WPC is to form hybridcomposites [1, 14-24]. Very popular WPC modifiers are nanoparticle additions like organonanoclays, which increase WPC physical-mechanical properties - microhardness, water resistance and diminish barrier properties and combustibility [1, 2, 14-17, 19, 20]. The goal of this study was to investigate organonanoclays influence on plywood production industry by-product birch plywood sawdust (PSWD) containing

Limited oxygen index levels of impregnated Scots pine wood

International Nuclear Information System (INIS)

Tomak, Eylem Dizman; Cavdar, Ayfer Donmez

2013-01-01

Highlights: • Scots pine samples were treated with 4 wood preservatives with various concentrations. • Limited oxygen index level was evaluated both for leached and un-leached samples. • All treatments improved fire retardance of samples despite some chemicals leached out. • Samples treated with fireproof agent showed the best results. • LOI of samples treated with boron powder and silicon oil was not changed by leaching. - Abstract: In this study, effect of various concentrations of boron powder, mixture of boric acid and borax, fireproof agent based on liquid blend of limestone, and silicon oil on limited oxygen index levels (LOI) of S. pine wood was investigated. Wood samples were first vacuum treated with the preservatives, and then were subjected to leaching procedure. Samples treated with fireproof agent showed the best results for improving the fire retardancy of wood, furthermore, samples treated with 25%, 50% and 100% of the solution did not burn. Leaching did not considerably change the LOI of wood samples treated with boron powder and silicon oil; however, LOI levels of samples treated with the mixture of boric acid and borax and fireproof agent were affected by leaching procedure probably arising those preservatives did not chemically bond to main wood components. All treatments improved fire retardancy of samples despite some amount of preservatives leached out from wood

Limited oxygen index levels of impregnated Scots pine wood

Energy Technology Data Exchange (ETDEWEB)

Tomak, Eylem Dizman, E-mail: eylemdizman@yahoo.com [Forest Industry Engineering Department, Faculty of Forestry, Bursa Technical University, 16200 Bursa (Turkey); Cavdar, Ayfer Donmez [Interior Architecture Department, Faculty of Architecture, Karadeniz Technical University, 61080 Trabzon (Turkey)

2013-12-10

Highlights: • Scots pine samples were treated with 4 wood preservatives with various concentrations. • Limited oxygen index level was evaluated both for leached and un-leached samples. • All treatments improved fire retardance of samples despite some chemicals leached out. • Samples treated with fireproof agent showed the best results. • LOI of samples treated with boron powder and silicon oil was not changed by leaching. - Abstract: In this study, effect of various concentrations of boron powder, mixture of boric acid and borax, fireproof agent based on liquid blend of limestone, and silicon oil on limited oxygen index levels (LOI) of S. pine wood was investigated. Wood samples were first vacuum treated with the preservatives, and then were subjected to leaching procedure. Samples treated with fireproof agent showed the best results for improving the fire retardancy of wood, furthermore, samples treated with 25%, 50% and 100% of the solution did not burn. Leaching did not considerably change the LOI of wood samples treated with boron powder and silicon oil; however, LOI levels of samples treated with the mixture of boric acid and borax and fireproof agent were affected by leaching procedure probably arising those preservatives did not chemically bond to main wood components. All treatments improved fire retardancy of samples despite some amount of preservatives leached out from wood.

Chemical changes and increased degradability of wheat straw and oak wood chips treated with the white rot fungi Ceriporiopsis subvermispora and Lentinula edodes

NARCIS (Netherlands)

Kuijk, van Sandra J.A.; Sonnenberg, Anton S.M.; Baars, Johan J.P.; Hendriks, Wouter H.; Río, del José C.; Rencoret, Jorge; Gutiérrez, Ana; Ruijter, de Norbert C.A.; Cone, John W.

2017-01-01

Wheat straw and oak wood chips were incubated with Ceriporiopsis subvermispora and Lentinula edodes for 8 weeks. Samples from the fungal treated substrates were collected every week for chemical characterization. L. edodes continuously grew during the 8 weeks on both wheat straw and oak wood chips,

Physical and chemical evaluation of furniture waste briquettes.

Science.gov (United States)

Moreno, Ana Isabel; Font, Rafael; Conesa, Juan A

2016-03-01

Furniture waste is mainly composed of wood and upholstery foam (mostly polyurethane foam). Both of these have a high calorific value, therefore, energy recovery would be an appropriate process to manage these wastes. Nevertheless, the drawback is that the energy content of these wastes is limited due to their low density mainly that of upholstery foam. Densification of separate foam presents difficulties due to its elastic character. The significance of this work lies in obtaining densified material by co-densification of furniture wood waste and polyurethane foam waste. Densification of furniture wood and the co-densification of furniture wood waste with polyurethane foam have been studied. On the one hand, the parameters that have an effect on the quality of the furniture waste briquettes have been analysed, i.e., moisture content, compaction pressure, presence of lignin, etc. The maximum weight percentage of polyurethane foam that can be added with furniture wood waste to obtain durable briquettes and the optimal moisture were determined. On the other hand, some parameters were analysed in order to evaluate the possible effect on the combustion. The chemical composition of waste wood was compared with untreated wood biomass; the higher nitrogen content and the concentration of some metals were the most important differences, with a significant difference of Ti content. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of Dielectric Barrier Discharge Plasma Treatment on Pentachlorophenol Removal of Granular Activated Carbon

International Nuclear Information System (INIS)

Ji Puhui; Qu Guangzhou; Li Jie

2013-01-01

The pentachlorophenol (PCP) adsorbed granular activated carbon (GAC) was treated by dielectric barrier discharge (DBD) plasma. The effects of DBD plasma on the structure of GAC and PCP decomposition were analyzed by N 2 adsorption, thermogravimetric, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and gas chromatography mass spectrometry (GC-MS). The experimental data of adsorption kinetics and thermodynamics of PCP on GAC were fitted with different kinetics and isotherm models, respectively. The results indicate that the types of N 2 adsorption isotherm of GAC are not changed by DBD plasma, while the specific surface area and pore volume increase after DBD plasma treatment. It is found that the weight loss of the saturated GAC is the highest, on the contrary, the weight loss of DBD treated GAC is the least because of reduced PCP residue on the GAC. The XPS spectra and SEM image suggest that some PCP on the GAC is removed by DBD plasma, and the surface of GAC treated by DBD plasma presents irregular and heterogeneous morphology. The GC-MS identification of by-products shows that two main dechlorination intermediate products, tetrachlorophenol and trichlorophenol, are distinguished. The fitting results of experimental data of adsorption kinetics and thermodynamics indicate that the pseudo-first-order and pseudo-second order models can be used for the prediction of the kinetics of virgin GAC and DBD treated GAC for PCP adsorption, and the Langmuir isotherm model fits better with the data of adsorption isotherm than the Freundlich isotherm in the adsorption of PCP on virgin GAC and DBD treated GAC

Effects of treated waste water irrigation on some qualitative charcterstics of forage sorghum, corn and millet

Directory of Open Access Journals (Sweden)

alireza emami

2009-06-01

Full Text Available In order to study the effects of irrigation with different levels of urban treated waste water on feeding value of forage sorghum (Var. Speed feed and Sugar graze, maize (Var. SC 704 and millet (Var. Nutrifeed an experiment was conducted at Experimental Station No.1, Astan Qods Razavi Mashhad, and Animal Nutrition Laboratory, College of Agriculture, Ferdowsi University of Mashhad. Four varieties of forage plants with five levels of treated waste water: %0, %25, %50, %75 and %100 were compared in a split-plot experiment based on Randomized Complete Block Design with four replications per treatment. Feeding values of forage plants such as Crude Protein content (CP, Neutral Detergent Fiber content (NDF, in vitro Dry Matter Digestibility (DMD, Organic Matter Digestibility (OMD and D-Value were measured. Results showed that treated waste water irrigation had a significant effect on crude protein content. The highest crude protein content was shown at % 100 treated waste water ( %13.76 and the lowest was shown at % treated waste water (%9.54. There were no significant differences between %0 and %25, and also %75 and %100 treated waste water in terms of crude protein content, but there were significant differences between %50 and other treated waste water treatments (except 75% treatments. There were no significant difference between irrigation with different levels of treated waste water in terms of NDF, in vitro DMD, OMD, and D-Value. There were significant differences between forage plants in all studied characteristics, but there were no significant differences on interactions between forage plants and different levels of treated waste water treatments. Forage maize had the highest in vitro DMD at %75 treated waste water and forage sorghum (var. Speed feed had the lowest in vitro DMD at %0 treated waste water treatments with averages of %77.57 and %61.6, respectively. The results indicated that treated waste water increased the percentage of crude

Wood frame systems for wood homes

Directory of Open Access Journals (Sweden)

Julio Cesar Molina

2010-12-01

Full Text Available The use of constructive systems that combine strength, speed, with competitive differential techniques and mainly, compromising with the environment, is becoming more popular in Brazil. The constructive system in wood frame for houses of up to five stories is very interesting, because it is a light system, structured in reforested treated wood which allows the combination of several materials, besides allowing speed in the construction and total control of the expenses already in the project phase for being industrialized. The structural behavior of the wood frame is superior to the structural masonry in strength, thermal and acoustic comfort. However, in Brazil, the wood frame is still little known and used, due to lack of technical knowledge about the system, prejudice associated the bad use of the wood as construction material, or still, in some cases, lack of normalization. The aim of this manuscript consists of presenting the main technical characteristics and advantages of the constructive system in wood frame homes, approaching the main stages of the constructive process through examples, showing the materials used in the construction, in addition the main international normative recommendations of the project. Thus, this manuscript also hopes to contribute to the popularization of the wood frame system in Brazil, since it is a competitive, fast and ecologically correct system. Moreover, nowadays, an enormous effort of the technical, commercial and industrial section has been accomplished for the development of this system in the country.

Morphology, composition, and mixing state of primary particles from combustion sources - crop residue, wood, and solid waste.

Science.gov (United States)

Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A P; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye; Li, Weijun

2017-07-11

Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combustion released OM and S-rich particles. Interestingly, particles from hardwood (pear wood and bamboo) and softwood (cypress and pine wood) combustion were mainly soot and OM in the flaming phase, respectively. The combustion of foam boxes, rubber tires, and plastic bottles/bags in the flaming phase released large amounts of soot internally mixed with a small amount of OM, whereas the combustion of printed circuit boards and copper-core cables emitted large amounts of OM with Br-rich inclusions. In addition, the printed circuit board combustion released toxic metals containing Pb, Zn, Sn, and Sb. The results are important to document properties of primary particles from combustion sources, which can be used to trace the sources of ambient particles and to know their potential impacts in human health and radiative forcing in the air.

A HEALTH SURVEY OF WORKERS IN THE PENTACHLOROPHENOL SECTION OF A CHEMICAL MANUFACTURING PLANT

NARCIS (Netherlands)

CHENG, WN; COENRAADS, PJ; HAO, ZH; LIU, GF

During 1968 to 1985, 109 workers who had been engaged in the production of pentachlorophenol, using non-gamma isomers of hexachloroclohexane (BHC) as the raw material, were surveyed. Endemic chloracne among them had been noted since 1974. The prevalence of chloracne was 73.4% (80/109) in total and

5000 sustainable workplaces - Wood energy provides work

International Nuclear Information System (INIS)

Keel, A.

2009-01-01

This article presents the results of a study made by the Swiss Wood Energy Association on the regional and national added value resulting from large wood-fired installations in Switzerland. The number of workplaces created by these installations is also noted. Wood energy is quoted as not only being a way of using forest wastes but also as being a creator of employment. Large wood-fired heating installations are commented on and efforts to promote this type of energy supply even further are discussed. The study indicates which professions benefit from the use of wood energy and quantifies the number of workplaces per megawatt of installed power that result.

Construction of Hydrophobic Wood Surface and Mechanical Property of Wood Cell Wall on Nanoscale Modified by Dimethyldichlorosilane

Science.gov (United States)

Yang, Rui; Wang, Siqun; Zhou, Dingguo; Zhang, Jie; Lan, Ping; Jia, Chong

2018-01-01

Dimethyldichlorosilane was used to improve the hydrophobicity of wood surface. The water contact angle of the treated wood surface increased from 85° to 143°, which indicated increased hydrophobicity. The nanomechanical properties of the wood cell wall were evaluated using a nanoindentation test to analyse the hydrophobic mechanism on the nano scale. The elastic modulus of the cell wall was significantly affected by the concentration but the influence of treatment time is insignificant. The hardness of the cell wall for treated samples was significantly affected by both treatment time and concentration. The interaction between treatment time and concentration was extremely significant for the elastic modulus of the wood cell wall.

STOCHASTIC HUMAN EXPOSURE AND DOSE SIMULATION MODEL FOR THE WOOD PRESERVATIVE SCENARIO (SHEDS-WOOD), VERSION 2 MODEL SAS CODE

Science.gov (United States)

Concerns have been raised regarding the safety of young children contacting arsenic and chromium residues while playing on and around Chromated Copper Arsenate (CCA) treated wood playground structures and decks. Although CCA registrants voluntarily canceled treated wood for resi...

Handling wood shavings

Energy Technology Data Exchange (ETDEWEB)

1974-09-18

Details of bulk handling equipment suitable for collection and compressing wood waste from commercial joinery works are discussed. The Redler Bin Discharger ensures free flow of chips from storage silo discharge prior to compression into briquettes for use as fuel or processing into chipboard.

The effect of some wood preservatives on the thermal degradation of Scots pine

International Nuclear Information System (INIS)

Tomak, Eylem D.; Baysal, Ergun; Peker, Huseyin

2012-01-01

Highlights: ► Scots pine samples were impregnated with 10 commercial wood preservatives. ► Thermal degradation of wood was evaluated by TG, DTG and DTA. ► The thermal behavior of treated wood differed from that of untreated wood. ► Boron containing wood preservatives yielded more charcoal than other preservatives. ► Boric oxide and metal compounds in the formulations may affect char weight. - Abstract: Wood has been a structural material for many years; however, its ability to burn has limited its use in some applications. This study aims to evaluate the effect of commercial wood preservatives having concentration of 4% on the thermal behavior of Scots pine wood, and compare the fire retardant effectiveness of these preservatives with that of boron compounds. Thermal degradation of treated and untreated wood samples was evaluated by thermogravimetry (TG), differential thermogravimetry (DTG) and differential thermal analysis (DTA). Thermal behavior of treated wood differed from thermal behavior of untreated wood in terms of a high char yield. Results showed that weight loss of wood reduced while char yield increased in the charring phase of the pyrolysis in the boron containing preservative treated wood accompanying with pyrolysis temperature lowered. The highest char yield was obtained from the samples treated with disodium octaborate tetrahydrate in the all treated groups.

Waste fatty acid addition to black liquor to decrease tall oil soap solubility and increase skimming efficiency in kraft mills pulping mountain pine beetle-infested wood

Energy Technology Data Exchange (ETDEWEB)

Uloth, V.; Guy, E. [FPInnovations, Prince George, BC (Canada). PAPRICAN Div.; Shewchuk, D. [Cariboo Pulp and Paper, Quesnel, BC (Canada); Van Heek, R. [Aker Kvaerner, Vancouver, BC (Canada)

2009-07-01

This paper presented the results of tests conducted to determine if the addition of waste fatty acids from vegetable oil processing might decrease tall oil soap solubility in pine-beetle impacted wood from British Columbia (BC). The soap recovery and tall oil production at BC mills has fallen by 30 to 40 percent in recent years due to the pulping of high proportions of grey-stage beetle-impacted wood. Full-scale mill tests were conducted over a 4-day period. The study showed that the addition of tall oil fatty acids or waste fatty acids from vegetable oil processing could decrease tall oil soap solubility and increase the soup skimming efficiency in mills pulping a large percentage of grey stage beetle-infested wood. The addition of fatty acids increased tall oil soap skimming efficiency from 50.2 percent in the baseline tests to 71.8 percent based on the total soap available, and from 76.7 percent in the baseline tests to 87.5 percent based on insoluble soap only. The economic analyses indicated that waste fatty acid addition could be economical when natural gas and oil prices are high. 4 tabs., 9 figs.

Advances in corrosion testing of metals in contact with treated wood

Science.gov (United States)

Samuel Zelinka; D.S. Stone

2010-01-01

A January 2004 change in the regulation of wood preservatives used in the U.S.has increased the use of newer wood preservatives, such as alkaline copper quaternary (ACQ) and copper azole (CuAz). These preservatives contain high amounts of cupric ions, which may be reduced to copper metal at the expense of less noble steel and galvanized fasteners in the wood....

Method of treating radioactive sludge waste

International Nuclear Information System (INIS)

Shoji, Yuichi; Matsuura, Hiroyuki; Ichihashi, Toshio

1989-01-01

For removing water content from sludge wastes, filtration or steam condensation may be considered, but none of them can sufficiently reduce the water content since filtration may cause clogging and steam treatment has a limit in the condensation. In view of the above, radioactive sludge wastes are dehydrated by an electroosmotic process in a vessel and then dehydrated solid contents are solidified in the vessel. Since the sludge wastes are mainly composed o fion exchange resins and iron oxides deposited to the resins, when a DC voltage is applied to the sludges containing such solid contents, a force tending to premeate them through the fine pores in the filter is exerted to water. As a result, only water is removed while the solids are being held on the filters. Since the moving direction of water is different depending on the property of the sludges, the polarity of the electrodes may be changed depending on the nature of the sludges. Thus, volume reduction can be improved and treating conditions can be controlled easily by a simple device. (N.H.)

Pentachlorophenol exposure causes Warburg-like effects in zebrafish embryos at gastrulation stage

International Nuclear Information System (INIS)

Xu, Ting; Zhao, Jing; Hu, Ping; Dong, Zhangji; Li, Jingyun; Zhang, Hongchang; Yin, Daqiang; Zhao, Qingshun

2014-01-01

Pentachlorophenol (PCP) is a prevalent pollutant in the environment and has been demonstrated to be a serious toxicant to humans and animals. However, little is known regarding the molecular mechanism underlying its toxic effects on vertebrate early development. To explore the impacts and underlying mechanisms of PCP on early development, zebrafish (Danio rerio) embryos were exposed to PCP at concentrations of 0, 20 and 50 μg/L, and microscopic observation and cDNA microarray analysis were subsequently conducted at gastrulation stage. The morphological observations revealed that PCP caused a developmental delay of zebrafish embryos in a concentration-dependent manner. Transcriptomic data showed that 50 μg/L PCP treatment resulted in significant changes in gene expression level, and the genes involved in energy metabolism and cell behavior were identified based on gene functional enrichment analysis. The energy production of embryos was influenced by PCP via the activation of glycolysis along with the inhibition of oxidative phosphorylation (OXPHOS). The results suggested that PCP acts as an inhibitor of OXPHOS at 8 hpf (hours postfertilization). Consistent with the activated glycolysis, the cell cycle activity of PCP-treated embryos was higher than the controls. These characteristics are similar to the Warburg effect, which occurs in human tumors. The microinjection of exogenous ATP confirmed that an additional energy supply could rescue PCP-treated embryos from the developmental delay due to the energy deficit. Taken together, our results demonstrated that PCP causes a Warburg-like effect on zebrafish embryos during gastrulation, and the affected embryos had the phenotype of developmental delay. - Highlights: • We treat zebrafish embryos with PCP at gastrula stage. • PCP acts as an oxidative phosphorylation inhibitor, not an uncoupler, in gastrulation. • Exogenous ATP injection will rescue the development of effected embryos. • The transcriptome of PCP-treated

Pentachlorophenol exposure causes Warburg-like effects in zebrafish embryos at gastrulation stage

Energy Technology Data Exchange (ETDEWEB)

Xu, Ting; Zhao, Jing [Key Laboratory of Yangtze River Water Environment, Ministry of Education, College of Environmental Science and Technology, Tongji University, Shanghai 200092 (China); Hu, Ping [Key Laboratory of Model Animal for Disease Study, Ministry of Education, Model Animal Research Center, Nanjing University, Nanjing 210061 (China); State Key Laboratory of Reproductive Medicine, Department of Prenatal Diagnosis, Nanjing Maternity and Child Health Care Hospital Affiliated to Nanjing Medical University, Nanjing 210029 (China); Dong, Zhangji; Li, Jingyun [Key Laboratory of Model Animal for Disease Study, Ministry of Education, Model Animal Research Center, Nanjing University, Nanjing 210061 (China); Zhang, Hongchang [Key Laboratory of Yangtze River Water Environment, Ministry of Education, College of Environmental Science and Technology, Tongji University, Shanghai 200092 (China); Yin, Daqiang, E-mail: yindq@tongji.edu.cn [Key Laboratory of Yangtze River Water Environment, Ministry of Education, College of Environmental Science and Technology, Tongji University, Shanghai 200092 (China); Zhao, Qingshun, E-mail: qingshun@nju.edu.cn [Key Laboratory of Model Animal for Disease Study, Ministry of Education, Model Animal Research Center, Nanjing University, Nanjing 210061 (China)

2014-06-01

Pentachlorophenol (PCP) is a prevalent pollutant in the environment and has been demonstrated to be a serious toxicant to humans and animals. However, little is known regarding the molecular mechanism underlying its toxic effects on vertebrate early development. To explore the impacts and underlying mechanisms of PCP on early development, zebrafish (Danio rerio) embryos were exposed to PCP at concentrations of 0, 20 and 50 μg/L, and microscopic observation and cDNA microarray analysis were subsequently conducted at gastrulation stage. The morphological observations revealed that PCP caused a developmental delay of zebrafish embryos in a concentration-dependent manner. Transcriptomic data showed that 50 μg/L PCP treatment resulted in significant changes in gene expression level, and the genes involved in energy metabolism and cell behavior were identified based on gene functional enrichment analysis. The energy production of embryos was influenced by PCP via the activation of glycolysis along with the inhibition of oxidative phosphorylation (OXPHOS). The results suggested that PCP acts as an inhibitor of OXPHOS at 8 hpf (hours postfertilization). Consistent with the activated glycolysis, the cell cycle activity of PCP-treated embryos was higher than the controls. These characteristics are similar to the Warburg effect, which occurs in human tumors. The microinjection of exogenous ATP confirmed that an additional energy supply could rescue PCP-treated embryos from the developmental delay due to the energy deficit. Taken together, our results demonstrated that PCP causes a Warburg-like effect on zebrafish embryos during gastrulation, and the affected embryos had the phenotype of developmental delay. - Highlights: • We treat zebrafish embryos with PCP at gastrula stage. • PCP acts as an oxidative phosphorylation inhibitor, not an uncoupler, in gastrulation. • Exogenous ATP injection will rescue the development of effected embryos. • The transcriptome of PCP-treated

The effect of some wood preservatives on the thermal degradation of Scots pine

Energy Technology Data Exchange (ETDEWEB)

Tomak, Eylem D., E-mail: eylemdizman@yahoo.com [Karadeniz Technical University, Faculty of Forestry, Forest Industrial Engineering Department, 61080 Trabzon (Turkey); Baysal, Ergun, E-mail: bergun@mu.edu.tr [Mugla University, Faculty of Technology, Department of Wood Science and Technology, Kotekli, 48000 Mugla (Turkey); Peker, Huseyin, E-mail: peker100@hotmail.com [Artvin Coruh University, Faculty of Forestry, Forest Industrial Engineering Department, 06100 Artvin (Turkey)

2012-11-10

Highlights: Black-Right-Pointing-Pointer Scots pine samples were impregnated with 10 commercial wood preservatives. Black-Right-Pointing-Pointer Thermal degradation of wood was evaluated by TG, DTG and DTA. Black-Right-Pointing-Pointer The thermal behavior of treated wood differed from that of untreated wood. Black-Right-Pointing-Pointer Boron containing wood preservatives yielded more charcoal than other preservatives. Black-Right-Pointing-Pointer Boric oxide and metal compounds in the formulations may affect char weight. - Abstract: Wood has been a structural material for many years; however, its ability to burn has limited its use in some applications. This study aims to evaluate the effect of commercial wood preservatives having concentration of 4% on the thermal behavior of Scots pine wood, and compare the fire retardant effectiveness of these preservatives with that of boron compounds. Thermal degradation of treated and untreated wood samples was evaluated by thermogravimetry (TG), differential thermogravimetry (DTG) and differential thermal analysis (DTA). Thermal behavior of treated wood differed from thermal behavior of untreated wood in terms of a high char yield. Results showed that weight loss of wood reduced while char yield increased in the charring phase of the pyrolysis in the boron containing preservative treated wood accompanying with pyrolysis temperature lowered. The highest char yield was obtained from the samples treated with disodium octaborate tetrahydrate in the all treated groups.

physico-chemical properties and energy potential of wood wastes

African Journals Online (AJOL)

user

were performed to assess the energy characteristics of the collected wood .... Methods. Wood processing activities were physically observed for. 6 days/wk at the sawmills for 15weeks. ..... [10] Oladeji, J T “Fuel characterization of briquettes.

Fertilization effects of organic waste resources and bottom wood ash: results from a pot experiment

Directory of Open Access Journals (Sweden)

Eva Brod

2012-12-01

Full Text Available We conducted a pot experiment to study the fertilization effects of four N- and P-rich organic waste resources alone and in combination with K-rich bottom wood ash at two application rates (150 kg N ha–1 + 120 kg K ha–1, 300 kg N ha-1 + 240 kg K ha–1. Plant-available N was the growth-limiting factor. 48–73% of N applied with meat and bone meal (MBM and composted fish sludge (CFS was taken up in aboveground biomass, resulting in mineral fertilizer equivalents (MFE% of 53–81% for N uptake and 61–104% for yield. MFE% of MBM and CFS decreased for increasing application rates. Two industrial composts had weak N fertilization effects and are to be considered soil conditioners rather than fertilizers. Possible P and K fertilization effects of waste resources were masked by the soil’s ability to supply plant-available P and K, but effects on plant-available P and K contents in soil suggest that the waste resources may have positive effects under more nutrient-deficient conditions.

Creation of Wood Dust during Wood Processing: Size Analysis, Dust Separation, and Occupational Health

Directory of Open Access Journals (Sweden)

Eva Mračková

2015-11-01

Full Text Available Mechanical separators and fabric filters are being used to remove airborne fine particles generated during the processing and handling of wood. Such particles might have a harmful effect on employee health, not only in small- but also in large-scale wood processing facilities. The amount of wood dust and its dispersion conditions vary according to geometric boundary conditions. Thus, the dispersion conditions could be changed by changing the linear size of the particles. Moreover, the smaller the particles are, the more harmful they can be. It is necessary to become familiar with properties, from a health point of view, of wood dust generated from processing. Wood dust has to be sucked away from the processing area. The fractional separation efficiency of wood dust can be improved using exhaust and filtering devices. Filtration efficiency depends on moisture content, particle size, and device performance. Because of the carcinogenicity of wood dust, the concentration of wood dust in air has to be monitored regularly. Based on the results hereof, a conclusion can be made that both mechanical separators of types SEA and SEB as well as the fabric filters with FINET PES 1 textile are suitable for the separation of wet saw dust from all types of wooden waste produced within the process.

Physical utilisation and conversion to energy of wastes arising in the wood industry; Stoffliche und energetische Abfallverwertung in der Holz- und Papierindustrie

Energy Technology Data Exchange (ETDEWEB)

Leithner, R. [Technische Univ. Braunschweig (Germany). Inst. fuer Waerme- und Brennstofftechnik; Marutzky, R. [Fraunhofer-Institut fuer Holzforschung, Wilhelm-Klauditz-Institut (WKI), Braunschweig (Germany)

1998-09-01

The present paper describes material streams in the paper and wood industry. It also points out possibilities for the physical utilisation and conversion to energy of wood waste and discusses the problems they involve. The authors give a brief overview of the of the plants used for this purpose along with illustrating examples. [Deutsch] Es werden Stoffstroeme in der Papier- und Holzindustrie aufgezeigt. Ferner werden stoffliche und energetische Verwertungsmoeglichkeiten von Holzabfaellen und Probleme dieser Verwertung beschrieben. Auch die Anlagen zu dieser Verwertung und einige Beispiele werden kurz zusammengefasst vorgestellt. (orig.)

Advanced air/flue gas staging based on CFD modelling for enhanced combustion and burnout in a waste-wood fired boiler

DEFF Research Database (Denmark)

Rajh, Boštjan; Yin, Chungen; Samec, Niko

2017-01-01

The paper presents the impacts of the jet momentum, position and orientation of air and Recycled Flue Gas (RFG) streams on the performance of a grate-fired boiler burning waste wood via a comprehensive CFD-based parametric study. It is found that the air and RFG jets can be optimized to enhance m...

Process and system for treating waste water

Science.gov (United States)

Olesen, Douglas E.; Shuckrow, Alan J.

1978-01-01

A process of treating raw or primary waste water using a powdered, activated carbon/aerated biological treatment system is disclosed. Effluent turbidities less than 2 JTU (Jackson turbidity units), zero TOC (total organic carbon) and in the range of 10 mg/l COD (chemical oxygen demand) can be obtained. An influent stream of raw or primary waste water is contacted with an acidified, powdered, activated carbon/alum mixture. Lime is then added to the slurry to raise the pH to about 7.0. A polyelectrolyte flocculant is added to the slurry followed by a flocculation period -- then sedimentation and filtration. The separated solids (sludge) are aerated in a stabilization sludge basin and a portion thereof recycled to an aerated contact basin for mixing with the influent waste water stream prior to or after contact of the influent stream with the powdered, activated carbon/alum mixture.

Acute toxicity of sodium chloride, pentachlorophenol, Guthion, and hexavalent chromium to fathead minnows (Pimephales promelas) and goldfish (Carassius auratus)

Energy Technology Data Exchange (ETDEWEB)

Adelman, I.R.; Smith, L.L. Jr.; Siesennop, G.D.

1976-02-01

The 96-h LC50's for sodium chloride were 7650 and 7341 mg/liter, for pentachlorophenol 0.21 and 0.22 mg/liter, for Guthion 1.9 and 2.4 mg/liter, and for hexavalent chromium 48 and 120 mg/liter, for fathead minnows (Pimephales promelas) and goldfish (Carassius auratus), respectively. Threshold LC50's were reached in 6 days for sodium chloride (7650 and 7322 mg/liter for fathead minnows and goldfish, respectively), and pentachlorophenol (0.21 and 0.21 mg/liter), but were not attained in 11 days (termination of testing) with Guthion (0.76 and 0.80 mg/liter) and hexavalent chromium (18 and 33 mg/liter). With pentachlorophenol and Guthion goldfish were initially more resistant, but by termination there was no significant difference in LC50's between the two species. With hexavalent chromium the goldfish were more resistant throughout the 11-day test, and with sodium chloride goldfish were initially more resistant but at attainment of a threshold LC50 were less resistant. Use of toxicity curves for assessment of acute mortality permits interpretation not possible in 96-h tests where LC50's are computed at 24-h intervals.

Determination of pentachlorophenol in water and aquifer sediments by high-performance liquid chromatography

Science.gov (United States)

Goerlitz, D.F.

1981-01-01

Methods for the determination of pentachlorophenol (PCP) in water and aquifer sediments are presented. Reverse-phase high-performance liquid chromotography employing ion suppression and gradient elution is used. PCP can be determined directly in water at a lower limit of detection Of 0.2 micrograms per liter. For extracts of sediment, PCP can be determined to a lower limit of 1.0 micrograms per kilogram.

Commercial Demonstration of Wood Recovery, Recycling, and Value Adding Technologies

Energy Technology Data Exchange (ETDEWEB)

Auburn Machinery, Inc.

2004-07-15

This commercial demonstration project demonstrated the technical feasibility of converting low-value, underutilized and waste stream solid wood fiber material into higher valued products. With a growing need to increase product/production yield and reduce waste in most sawmills, few recovery operations and practically no data existed to support the viability of recovery operations. Prior to our efforts, most all in the forest products industry believed that recovery was difficult, extremely labor intensive, not cost effective, and that recovered products had low value and were difficult to sell. This project provided an opportunity for many within the industry to see through demonstration that converting waste stream material into higher valued products does in fact offer a solution. Our work, supported by the U.S. Department of Energy, throughout the project aimed to demonstrate a reasonable approach to reducing the millions of recoverable solid wood fiber tons that are annually treated as and converted into low value chips, mulch and fuel. Consequently sawmills continue to suffer from reduced availability of forest resources, higher raw material costs, growing waste disposal problems, increased global competition, and more pressure to operate in an Environmentally Friendly manner. It is our belief (based upon the experience of this project) that the successful mainstreaming of the recovery concept would assist in alleviating this burden as well as provide for a realistically achievable economic benefit to those who would seriously pursue the concept and tap into the rapidly growing ''GREEN'' building marketplace. Ultimately, with participation and aggressive pursuit of the recovery concept, the public would benefit in that: (1) Landfill/disposal waste volume could be reduced adding greater life to existing municipal landfill sites thereby minimizing the need to prematurely license and open added facilities. Also, there would be a cost

Environmental Degradation of Fiber-Reinforced Polymer Fasteners in Wood

Science.gov (United States)

Samuel L. Zelinka; Douglas R. Rammer

2013-01-01

This paper examines the durability of fiber-reinforced polymer (FRP) nails in treated wood. The FRP nails were exposed to four conditions: (1) accelerated weathering, consisting of exposure to ultraviolet light and condensation; (2) 100% relative humidity (RH); (3) being driven into untreated wood and exposed to 100% RH; and (4) being driven into wood treated with...

Towards controlling dioxins emissions from power boilers fuelled with salt-laden wood waste

International Nuclear Information System (INIS)

Luthe, C.; Karidio, I.; Uloth, V.

1997-01-01

An evaluation of the dioxins emissions from a power boiler fuelled with salt-laden wood waste has provided insights on potential control technologies. Whereas a reduction in stack particulate levels does not preclude a corresponding reduction in dioxins emissions, good combustion conditions, in combination with an efficient secondary collection device for particulate removal, were found to offer effective control (stack emissions of 0.064 to 0.086 ng TEQ/m 3 ). Regarding minimization of dioxins formation at source, a preliminary assessment of the possible beneficial effect of an attenuated chlorine:sulphur ratio was encouraging. A more accurate assessment requires additional trials, preferably longer in duration, to eliminate any possible memory effects. (author)

Wood-waste fuelled indirectly-fired gas turbine cogeneration plant for sawmill applications. Phase 2. Site-specific preliminary engineering and financial analysis

Energy Technology Data Exchange (ETDEWEB)

1988-03-01

The use of conventional steam/electricity cogeneration systems is not generally economical at the sawmill scale of operation. This paper describes an evaluation of a wood-waste fueled and, indirectly, gas fired turbine cogeneration plant aimed at developing a cost-effective wood-waste fired power generation and dry kiln heating system for sawmill applications. A preliminary engineering design and financial analysis of the system was prepared for a demonstration site in British Columbia. A number of alternative system configurations were identified and preliminary engineering designs prepared for each. In the first option , wood wastes combusted in a wet cell hot gas generator powered a 600 kW turbine, and produced 7,000 kW for the drying kilns. The second option provided the same electrical and heat output but used a down-fired suspension burner unit fuelled by clean, dried sawdust, together with an integral air heater heat exchanger. The third option represented a commercial-scale configuration with an electrical output of 1,800 kW, and sufficient heat output for the dry kilns. A financial analyis based on a computerized feasibility model was carried out on the last two options. Low electricity rates in British Columbia combined with the small scale of a demonstration project provide an inadequate rate of return at the site without substantial outside support. At a commercial scale of operation and with the higher electricity prices that exist outside of British Columbia the financial analysis indicates that the incremental investment in the electric generation portion of the system provides very attractive rates of return for the 3 options. 11 figs., 10 tabs.

A General Evaluation for Recycling Process of Impregnated Wood Removed From the Service

Directory of Open Access Journals (Sweden)

Cihat Taşçıoğlu

2011-03-01

Full Text Available Wood presevatives such as creosote, pentaclorophenol (PCP and chromated copper arsenate (CCA have been widely used over the years in order to extend wood products’ service life. CCA was known as most widely used wood preservative chemical in residendial and commercial applications world wide until 2004 volanteered phase out of the chemical from residential use bye the major manufacturers. Over the years CCA treated wood acuumulated in service reaching millions of cubic meters. But there is growing concern about the environmental impacts and increasing difficulty in disposing of treated wood products in many countries. Since disposal of CCA treated wood material poses greater problems than the other treated wood products due to heavy and toxic metal componets of CCA such as chromium and arsenic Traditional disposal methods like landfillig or incineration, both have negative environmental consequences. For that reason the increasing volume of CCA-treated wood products coming out of service requires alternative disposal methods and recycling techniques never tried before. The main purpose of this study, except for traditional methods like landfilling and incineration, is to evaluate the current alternative disposal and recycling methods for CCA treated wood removed from service.

Weathering properties of treated southern yellow pine wood examined by X-ray photoelectron spectroscopy, scanning electron microscopy and physical characterization

Energy Technology Data Exchange (ETDEWEB)

Salaita, Ghaleb N.; Ma, Frank M.S.; Parker, Trudy C. [Dow Chemical Company, Technical Center, 3200 Kanawha Turnpike, South Charleston, WV 25303 (United States); Hoflund, Gar B. [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611 (United States)], E-mail: garho@hotmail.com

2008-04-30

In this study the weathering behavior of southern yellow pine (SYP) wood samples pretreated in different solutions has been examined using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and various types of physical characterization regarding material loss and discoloration. The treatment solutions include water as a control, a commercially available water repellent (WR) wood treating additive and polyethylene glycol (PEG) products including PEG PLUS{sup TM}, PEG 8000 solutions and Compound 20M in varying concentrations. All contained the wood preservative chromated copper arsenate (CCA). One sample was treated with a CCA solution only. The treatments were carried out at 20 deg. C and 150 psig for 1/2 h after exposure to vacuum (28 mmHg) for 15 min. Simulated weathering was achieved in an Atlas 65-W Weather-Ometer for 2000 h with both light and dark periods and rain. The temperature ranged from 23 deg. C during the dark cycle to 35 deg. C during the light cycle. With weathering the XPS O/C ratios increase due to oxidation of the surface. Exposure to UV light results in bond breakage and reaction with oxygen in the presence of air to form organic functional groups such as , , C=O and/or O-C-O. These oxidized products can protect the underlying wood from deterioration if they are insoluble in water and remain on the surface as a protective coating. If soluble, rain washes the compounds away and assists in the degradation. Correlated changes are observed in the XPS O/C ratios, the high-resolution XPS C 1s spectra, the SEM micrographs and physical measurements including thickness alteration, weight loss, and discoloration by yellowing or whitening of the weathered wood. The PEG treatments are effective in protecting wood with the 2% PEG PLUS treatment providing the best weathering behavior similar to that of the CCA treatment. The WR and water treatments yield the poorest weathering properties.

Weathering properties of treated southern yellow pine wood examined by X-ray photoelectron spectroscopy, scanning electron microscopy and physical characterization

International Nuclear Information System (INIS)

Salaita, Ghaleb N.; Ma, Frank M.S.; Parker, Trudy C.; Hoflund, Gar B.

2008-01-01

In this study the weathering behavior of southern yellow pine (SYP) wood samples pretreated in different solutions has been examined using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and various types of physical characterization regarding material loss and discoloration. The treatment solutions include water as a control, a commercially available water repellent (WR) wood treating additive and polyethylene glycol (PEG) products including PEG PLUS TM , PEG 8000 solutions and Compound 20M in varying concentrations. All contained the wood preservative chromated copper arsenate (CCA). One sample was treated with a CCA solution only. The treatments were carried out at 20 deg. C and 150 psig for 1/2 h after exposure to vacuum (28 mmHg) for 15 min. Simulated weathering was achieved in an Atlas 65-W Weather-Ometer for 2000 h with both light and dark periods and rain. The temperature ranged from 23 deg. C during the dark cycle to 35 deg. C during the light cycle. With weathering the XPS O/C ratios increase due to oxidation of the surface. Exposure to UV light results in bond breakage and reaction with oxygen in the presence of air to form organic functional groups such as , , C=O and/or O-C-O. These oxidized products can protect the underlying wood from deterioration if they are insoluble in water and remain on the surface as a protective coating. If soluble, rain washes the compounds away and assists in the degradation. Correlated changes are observed in the XPS O/C ratios, the high-resolution XPS C 1s spectra, the SEM micrographs and physical measurements including thickness alteration, weight loss, and discoloration by yellowing or whitening of the weathered wood. The PEG treatments are effective in protecting wood with the 2% PEG PLUS treatment providing the best weathering behavior similar to that of the CCA treatment. The WR and water treatments yield the poorest weathering properties

Effect of boron compounds on the thermal and combustion properties of wood-plastic composites

OpenAIRE

Altuntaş, Ertuğrul; Karaoğul, Eyyup; Alma, Mehmet Hakkı

2017-01-01

In this study, the thermal properties and fire resistancesof the wood plastic composites produced with waste lignocellulosic materialswere investigated. For this purpose, lignocellulosic waste, high densitypolyethylene, (HDPE) sodium borate (borax) and boric acid was used to producethe wood-plastic composites. A twin-screw extruder was used during theproduction of the wood plastic composites. The produced composite granule waspressed at 175 °C hot press. The effects of boric acid and borax ad...

Evaluation of energy efficient techniques in the wood working and wood processing industry. Final report THERMIE - Action no. DIS-0059-95-DE

Energy Technology Data Exchange (ETDEWEB)

Eichhammer, W.; Digutsch, O.; Frey, G. v. [and others

1997-05-01

With the entrance of Austria, Finland and Sweden in the European Union beginning of 1995 the pattern of industrial energy consumption has changed considerably in some branches which are large energy consumers in the Northern countries. The wood working and wood processing industry is one of those branches. It comprises the preparation of wood from primary processing in sawmills up to the production of finished products, and is highly energy-intensive although to a somewhat smaller extent than the large energy consumers such as the iron and steel production or glass manufacturing. It can further be assumed that official statistics underestimate the real importance of the energy consumption in the wood sector because most official statistics do not indicate waste wood as a fuel. Waste wood is a renewable fuel and has as such not the same impact in terms of CO{sub 2}-emissions as fossil fuels. Nevertheless, renewable energy sources should be also used efficiently because they can replace fossil fuels for other purposes. The objective of this study on the wood sector were to analyse and summarise the present status of energy consumption in the fifteen countries of the EU and the two EFTA countries Norway and Switzerland, to evaluate present day energy technology in the wood industry, and to investigate existing application barriers to these techniques in order to inform, support and to motivate small and medium-sized companies in particular, thus simulating the wide spread use of such techniques. (orig./SR)

Effect of drying on leaching testing of treated municipal solid waste incineration APC-residues

DEFF Research Database (Denmark)

Hu, Y.; Hyks, Jiri; Astrup, Thomas

2008-01-01

Air-pollution-control (APC) residues from waste incinerators are hazardous waste according to European legislation and must be treated prior to landfilling. Batch and column leaching data determine which type of landfill can receive the treated APC-residues. CEN standards are prescribed...

Thermogravimetric analysis of combustible waste components

DEFF Research Database (Denmark)

Munther, Anette; Wu, Hao; Glarborg, Peter

In order to gain fundamental knowledge about the co-combustion of coal and waste derived fuels, the pyrolytic behaviors of coal, four typical waste components and their mixtures have been studied by a simultaneous thermal analyzer (STA). The investigated waste components were wood, paper, polypro......In order to gain fundamental knowledge about the co-combustion of coal and waste derived fuels, the pyrolytic behaviors of coal, four typical waste components and their mixtures have been studied by a simultaneous thermal analyzer (STA). The investigated waste components were wood, paper...

Chromatography Of Metal Ions On Wood Cellulose Impregnated ...

African Journals Online (AJOL)

Adsorption chromatography of some heavy metal ions on wood cellulose of saw dust (wood waste dust) modified with hydrochloric acid, urea and thiourea was studied. Atomic absorption spectrophotometry (AAS) was used to determine the initial concentration of solutions of Zn2+, Cu2+, Ni2+, Pb2+, and Fe3+ metal ions.

Electrochemical impedance spectroscopy (EIS) as a tool for measuring corrosion of polymer-coated fasteners used in treated wood

Science.gov (United States)

Samuel L. Zelinka; Lorraine Ortiz-Candelaria; Donald S. Stone; Douglas R. Rammer

2009-01-01

Currently, many of the polymer-coated fasteners on the market are designed for improved corrosion performance in treated wood; yet, there is no way to evaluate their corrosion performance. In this study, a common technique for measuring the corrosion performance of polymer-coated metals, electrochemical impedance spectroscopy (EIS), was used to evaluate commercial...

Corrosion of metals in wood : comparing the results of a rapid test method with long-term exposure tests across six wood treatments

Science.gov (United States)

Samuel L. Zelinka; Donald S. Stone

2011-01-01

This paper compares two methods of measuring the corrosion of steel and galvanized steel in wood: a long-term exposure test in solid wood and a rapid test method where fasteners are electrochemically polarized in extracts of wood treated with six different treatments. For traditional wood preservatives, the electrochemical extract method correlates with solid wood...

Evaluation of Trichoderma harzanium treated cassava waste on the ...

African Journals Online (AJOL)

SERVER

2007-09-19

Sep 19, 2007 ... Microbial Biotechnology and Dairy Science Laboratory, Department of Animal ... Trichoderma treated cassava waste was beneficial to lactating West African dwarf goats. .... Animals that did not show any signs of heat were.

A wood-waste fuelled indirectly-fired gas turbine cogeneration plant for sawmill application. Preliminay engineering and financial evaluation. Phase 1

Energy Technology Data Exchange (ETDEWEB)

1986-02-01

The overall objective of this project is to develop a cost-effective wood waste-fired power generation and lumber drying system for Canadian sawmill applications. The system proposed and evaluated in this project is a wood waste-fuelled, indirectly-fired gas turbine cogeneration plant. Research, design and development of the system has been planned to take place in a number of phases. The first phase consists of a preliminary engineering design and financial evaluation of the system and is the subject of this report. This analysis focuses on British Columbia since it is the largest potential market for the sawmill cogeneration system. In order to provide design parameters for the cogeneration system, operational characteristics were compiled for a typical sawmill in the interior of British Columbia. A number of alternative design concepts were reviewed before arriving at the indirect-fired turbine concept selected for development in this project. The general concept involves the use of an open Brayton-cycle gas turbine as the prime mover to generate electrical power, while process heat for the dry-kiln is obtained by waste heat recovery from the turbine exhaust gas. The proposed system has many advantages over a conventional steam based cogeneration system and economic analysis indicates that the system generates very attractive financial returns over a variety of conditions. 7 refs., 8 figs., 8 tabs.

Assessment of chemical and material contamination in waste wood fuels--A case study ranging over nine years.

Science.gov (United States)

Edo, Mar; Björn, Erik; Persson, Per-Erik; Jansson, Stina

2016-03-01

The increased demand for waste wood (WW) as fuel in Swedish co-combustion facilities during the last years has increased the import of this material. Each country has different laws governing the use of chemicals and therefore the composition of the fuel will likely change when combining WW from different origins. To cope with this, enhanced knowledge is needed on WW composition and the performance of pre-treatment techniques for reduction of its contaminants. In this study, the chemical and physical characteristics of 500 WW samples collected at a co-combustion facility in Sweden between 2004 and 2013 were investigated to determine the variation of contaminant content over time. Multivariate data analysis was used for the interpretation of the data. The concentrations of all the studied contaminants varied widely between sampling occasions, demonstrating the highly variable composition of WW fuels. The efficiency of sieving as a pre-treatment measure to reduce the levels of contaminants was not sufficient, revealing that sieving should be used in combination with other pre-treatment methods. The results from this case study provide knowledge on waste wood composition that may benefit its management. This knowledge can be applied for selection of the most suitable pre-treatments to obtain high quality sustainable WW fuels. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Symposium on extending the use of wood residue

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

A symposium on extending the use of wood residues was held in Geneva, Switzerland in June, 1977. These meetings were sponsored by the UN Economic Commission for Europe, Timber Committee for the purpose of sharing information and ideas on recycling wood wastes. Eight separate papers were abstracted for inclusion in the Energy Data Base.

Hydroxyl-radical induced dechlorination of pentachlorophenol in water

International Nuclear Information System (INIS)

He Yongke; Wu Jilan; Fang Xingwang; Sonntag, C. von

1998-01-01

The hydroxyl-radical induced dechlorination of pentachlorophenol (PCP) in water has been investigated pulse radiolytically. Hydroxyl radicals react with PCP by both electron transfer and addition. The former process results in pentachlorophenoxyl radicals (PCP-O), the latter process followed by rapid HCl elimination gives birth to deprotonated hydroxytetrachlorophenoxyl radicals ( - O-TCP-O). These phenoxyl radicals exhibit maximum absorption around 452 nm, which hinders the proper estimation of the ratio of the two processes. However, these two processes cause different changes in conductivity. In basic solution, the electron transfer causes a conductivity increase due to the formation of OH - whereas an addition followed by HCl elimination results in a conductivity decrease. The concurrence of these two processes reduces the relative variation in conductivity, from which about 53% electron transfer is deduced

Pentachlorophenol from an old henhouse as a dioxin source in eggs and related human exposure.

Science.gov (United States)

Piskorska-Pliszczynska, Jadwiga; Strucinski, Pawel; Mikolajczyk, Szczepan; Maszewski, Sebastian; Rachubik, Jaroslaw; Pajurek, Marek

2016-01-01

High levels of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were detected in free-range eggs, and these levels reached a concentration of 29.84 ± 7.45 pg of WHO-TEQ/g of fat. This value exceeded the EU maximum permitted level of 2.5 pg of WHO-TEQ/g of fat for PCDD/F congeners by twelve-fold. A chemical analysis (HRGC-HRMS) revealed elevated amounts of OCDD, OCDF, HxCDD, HpCDD and HpCDF. During the investigation, samples of feed, soil, wall scrapings, wooden ceiling of the henhouse and tissues from laying hens were examined for dioxin contents (30 samples altogether). The long and complicated investigation found that the source of dioxins in the poultry farm was pentachlorophenol-treated wood, which was used as structural components in the 40-year-old farm building adapted to a henhouse. The wooden building material contained PCDD/Fs at a concentration of 3922.60 ± 560.93 pg of WHO-TEQ/g and 11.0 ± 2.8 μg/kg of PCP. The potential risk associated with dioxin intake was characterized by comparing the theoretically calculated weekly and monthly intakes with the toxicological reference values (TRVs), namely the Tolerable Weekly Intake (TWI) and Provisional Tolerable Monthly Intake (PTMI) values of 14 pg of WHO-TEQ/kg of bw and 70 pg of WHO-TEQ/kg of bw, respectively. The intake of dioxins estimated for high egg consumers (approximately 5-6 eggs/week) exceeded the TWI and PTMI values, which may pose a risk of delayed adverse health effects. The estimated dose of PCDD/Fs and DL-PCBs for children consuming 5 eggs per week exceeded the TWI by as much as 450% because of their nearly 5-fold-lower body weight. Although the dioxin intake estimated for the average consumption of eggs in the general population did not exceed any of the TRVs applied (58.7% TWI and 51.1% PTMI), such a situation should be considered unacceptable from a public health perspective because eggs are not the only source of these contaminants. Copyright © 2015

A Review of Wood Plastic Composites effect on the Environment

Directory of Open Access Journals (Sweden)

Ahmed Taifor Azeez

2017-05-01

Full Text Available Wood Plastic Composites (WPCs are environmentally friend materials with a wide range of applications in the field of constructions, comprising high mechanical and physical properties with low cost raw materials as plastic wastes and different carpentry process wood reminder. The effects of wood, plastic waste and additives on various properties of the material such as mechanical (modulus of elasticity and modulus of rupture, physical (moisture absorption and fire retardancy have been investigated in order to push the output functions of the products to the limits of work conditions requirements. This study, overviews the importance of Wood Plastic Composites in conserving the environment by depletion post consume plastics from landfills, and the impact of these composites in developing the economic via opening new flourished markets for modern products. Both the ecological and economical requirements oblige the Iraqi government to replace the negatively healthy effects formaldehyde wood composites (medium density fiberboard MDF which are widely consumed in Iraqi markets with Wood Plastic Composites. a long-term strategy plan in which the researchers and the capitals meet under supervision of the government is very necessary and recommended in this paper to establish and develop WPCs industry in Iraq.

Development of a database system for the management of non-treated radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Pinto, Antônio Juscelino; Freire, Carolina Braccini; Cuccia, Valeria; Santos, Paulo de Oliveira; Seles, Sandro Rogério Novaes; Haucz, Maria Judite Afonso, E-mail: ajp@cdtn.br, E-mail: cbf@cdtn.br, E-mail: vc@cdtn.br, E-mail: pos@cdtn.br, E-mail: seless@cdtn.br, E-mail: hauczmj@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The radioactive waste produced by the research laboratories at CDTN/CNEN, Belo Horizonte, is stored in the Non-Treated Radwaste Storage (DRNT) until the treatment is performed. The information about the waste is registered and the data about the waste must to be easily retrievable and useful for all the staff involved. Nevertheless, it has been kept in an old Paradox database, which is now becoming outdated. Thus, to achieve this goal, a new Database System for the Non-treated Waste will be developed using Access® platform, improving the control and management of solid and liquid radioactive wastes stored in CDTN. The Database System consists of relational tables, forms and reports, preserving all available information. It must to ensure the control of the waste records and inventory. In addition, it will be possible to carry out queries and reports to facilitate the retrievement of the waste history and localization and the contents of the waste packages. The database will also be useful for grouping the waste with similar characteristics to identify the best type of treatment. The routine problems that may occur due to change of operators will be avoided. (author)

Development of a database system for the management of non-treated radioactive waste

International Nuclear Information System (INIS)

Pinto, Antônio Juscelino; Freire, Carolina Braccini; Cuccia, Valeria; Santos, Paulo de Oliveira; Seles, Sandro Rogério Novaes; Haucz, Maria Judite Afonso

2017-01-01

The radioactive waste produced by the research laboratories at CDTN/CNEN, Belo Horizonte, is stored in the Non-Treated Radwaste Storage (DRNT) until the treatment is performed. The information about the waste is registered and the data about the waste must to be easily retrievable and useful for all the staff involved. Nevertheless, it has been kept in an old Paradox database, which is now becoming outdated. Thus, to achieve this goal, a new Database System for the Non-treated Waste will be developed using Access® platform, improving the control and management of solid and liquid radioactive wastes stored in CDTN. The Database System consists of relational tables, forms and reports, preserving all available information. It must to ensure the control of the waste records and inventory. In addition, it will be possible to carry out queries and reports to facilitate the retrievement of the waste history and localization and the contents of the waste packages. The database will also be useful for grouping the waste with similar characteristics to identify the best type of treatment. The routine problems that may occur due to change of operators will be avoided. (author)

INFLUENCE OF SOLVENT AND SORBENT CHARACTERISTICS ON DISTRIBUTION OF PENTACHLOROPHENOL IN OCTANOL-WATER AND SOIL-WATER SYSTEMS

Science.gov (United States)

Sorbent and solvent characteristics influencing sorption of pentachlorophenol (PCP) were investigated. Analysis of aqueous sorption data for several sorbents over a broad pH range suggested hydrophobic sorption of neutral PCP predominates at pH 7. At pH > 7, sorption of the penta...

Thermal Properties of Wood-Plastic Composites Prepared from Hemicellulose-extracted Wood Flour

Directory of Open Access Journals (Sweden)

A.A. Enayati

2013-01-01

Full Text Available Hemicellulose of Southern Yellow Pine wood spices was extracted by pressurized hot water at three different temperatures: 140°C, 155°C and 170°C. Compounding with PP (polypropylene was performed by extrusion after preparing wood flour and sieving to determine its mesh size. The ratio of wood to polymer was 50:50 based on oven-dry weight of wood flour. All extraction treatments and control samples were compounded under two sets of conditions, without and with 2% MAPP as coupling agent. Injection molding was used to make tensile test samples (dogbone from the pellets made by extrusion. Thermal properties of wood-plastic composites were studied by TGA and DSC while the thermal stability of pretreated wood flours, PP and MAPP were studied by TGA as well. The greater weight loss of wood materials was an indication that higher treatment temperature increases the extractability of hemicellulose. The removal of hemicellulose by extraction improves thermal stability of wood flour, especially for extraction at 170°C. Wood-plastic composites made from extracted fibers at 170°C showed the highest thermal stability. Coupling agent did not have a significant effect on thermal stability but it improved the degree of crystallinity of the composites.Surface roughness of wood fiber increased after treatment. Extraction of hemicellulose increased the degree of crystallinity but it was not significant except for samples from treated wood flour at 170°C and with MAPP.

Preparation Of Charcoal Using Agricultural Wastes | Bogale ...

African Journals Online (AJOL)

Conclusion: As compared to wood charcoal the charcoal briquette produced from agricultural wastes are economical, environmentally friendly, healthy (no smoke at all) and reduce impact of deforestation. Key words: Pollution, deforestation, extruder, carbonizer, wood charcoal, briquette charcoal, agricultural wastes, ...

Cytochemical localization of cellulases in decayed and nondecayed wood

Energy Technology Data Exchange (ETDEWEB)

Murmanis, L.; Highley, T.L.; Palmer, J.G.

1987-01-01

Sawdust from undecayed western hemlock wood and from wood previously decayed by the brown-rot fungus Poria placenta or by the white-rot fungus Ganoderma applanatum was incubated with commercial cellulase from Trichoderma viride. Samples were treated cytochemically to locate cellulase activity and examined by TEM. Results showed that cellulase degraded undecayed wood extensively, with the attack starting on the outer border of a cell wall and progressing inside. Wood decayed by P. placenta, with or without cellulase incubation, and treated by the cytochemical test showed uniform distribution of electron dense particles throughout the cell walls. In wood decayed by G. applanatum, cellulase degradation was similar to that in undecayed wood. From measurements of particle diameter it is suggested that electron dense particles are cellulase. It is concluded that brown-rot and white-rot fungi have different effects on the microstructure of wood. The brown-rot fungus appears to open the wood microstructure so that cellulase can diffuse throughout the degraded tracheid wall.

Fracture analysis of cement treated demolition waste using a lattice model

NARCIS (Netherlands)

Xuan, D.; Schlangen, H.E.J.G.; Molenaar, A.A.A.; Houben, L.J.M.

2013-01-01

Fracture properties of cement treated demolition waste were investigated using a lattice model. In practice the investigated material is applied as a cement treated road base/subbase course. The granular aggregates used in this material were crushed recycled concrete and masonry. This results in six

Measurements of emissions during waste wood combustion to identify refurbishment needs; Maetning av emissioner vid foerbraenning av RT-flis foer att identifiera eventuella ombyggnadsaatgaerder

Energy Technology Data Exchange (ETDEWEB)

Lindau, Leif

2003-01-01

The background to this project is the new EU directive 2000/76/EG regarding incineration of waste. This directive may have an effect on emission limits for Swedish plants firing waste wood. It may lead to needs of refurbishment in e.g. the area of flue gas cleaning equipment. In order to produce a basis to evaluate the need for such upgrading, measurement of metals, HCI, SO{sub 2} , CO, TOC and dioxin have been carried out on three plants firing wood waste: a grate boiler (Handeloeverket P11), one circulating fluid bed boiler (Aaterbruket in Lomma), and a bubbling fluidised bed boiler (Johannes in Gaevle, firing 50% waste wood). The measurements have mainly been carried out after boiler, equivalent to upstream flue gas cleaning. The results are that the demands of the EU directive on most points can be managed with existing equipment if this consists of electrostatic precipitator or bag filter with good performance and flue gas condensor. Without flue gas condensor, there is a need for other measures for 1-10 and for grate boilers, SO{sub 2} as well. The requirements in the directive for TOC is weaker than the demand on CO, and correspondingly, the demand on CO is driving. The level of dioxin from the boiler (upstream filter) exceeds allowed emission, and is in the range of 0,1-2 ng TE/Nm{sup 3} tg, 6 % O{sub 2} . Existing equipment will meet the emission limit for the lower levels (0,1-0,3) , but not safely for the higher levels (1,5-2). Correspondingly, there may be a need for equipment upgrading, e.g. in the form of activated carbon injection upstream flue gas filter.

A comparative study on Cu, Cr and As removal from CCA-treated wood waste by dialytic and electrodialytic processes

DEFF Research Database (Denmark)

Velizarova, Emiliya; Ribeiro, Alexandra B.; Ottosen, Lisbeth M.

2002-01-01

with the performance of a pure dialytic experiment (without an external power supply) in order to reveal transport of charged particles induced solely by internal electrochemical potential differences in the system. Oxalic acid proved to be a more suitable pre-treatment solution than deionised water for wood chips...

A New Technology for Treating Pulp Waste with Plasma

International Nuclear Information System (INIS)

Feng Xiaozhen; Tian Zhongyu

2009-01-01

New methods for both the treatment of pulp waste liquor called black liquor (BL) and the recovery of chemicals by using plasma, and the concentration of BL with the freezing technique were developed. The new methods aiming at the pilot plant scale are described and the experiments in a small-scale research facility for demonstration and test are presented. The energy consumption for treating waste liquid is 1 kg/kWh. Plasma processing can reduce the costs for treatment and eliminate pollution. (plasma technology)

Waste minimization methods for treating analytical instrumentation effluents at the source

International Nuclear Information System (INIS)

Ritter, J.A.; Barnhart, C.

1995-01-01

The primary goal of this project was to reduce the amount of hazardous waste being generated by the Savannah River Siste Defense Waste Processing Technology-analytical Laboratory (DWPT-AL). A detailed characterization study was performed on 12 of the liquid effluent streams generated within the DWPT-AL. Two of the streams were not hazardous, and are now being collected separately from the 10 hazardous streams. A secondary goal of the project was to develop in-line methods using primarily adsorption/ion exchange columns to treat liquid effluent as it emerges from the analytical instrument as a slow, dripping flow. Samples from the 10 hazardous streams were treated by adsorption in an experimental apparatus that resembled an in-line or at source column apparatus. The layered adsorbent bed contained activated carbon and ion exchange resin. The column technique did not work on the first three samples of the spectroscopy waste stream, but worked well on the next three samples which were treated in a different column. It was determined that an unusual form of mercury was present in the first three samples. Similarly, two samples of a combined waste stream were rendered nonhazardous, but the last two samples contained acetylnitrile that prevented analysis. The characteristics of these streams changed from the initial characterization study; therefore, continual, in-deptch stream characterization is the key to making this project successful

Proceedings of the 7. biennial residue-to-revenue residual wood conference 2007

International Nuclear Information System (INIS)

Raulin, J.

2007-01-01

This conference provided information on the highest and best use of residual wood, which is quickly becoming a valuable commodity. Issues concerning forest residues, sawmill wastes, agricultural residues and urban organic materials were discussed along with trends in Canadian surplus mill waste production. The evolving nature and technologies of the biomass business were highlighted with particular focus on how to generate energy and save money through the use of residual wood. Residual wood energy projects and developments in Canada, North America and Europe were outlined along with biomass development in relation to forest fires and insect disturbances. Cogeneration technologies using wood wastes for thermal heat, steam and electricity were also presented, along with transportation fuel technologies for the production of ethanol. It was noted that with the rising cost of energy, the forest industry is seeking energy solutions based on the use of residual wood. The range of economically practical residual wood solutions continues to grow as energy prices increase. The conference was attended by more than 200 delegates from the forest industry, suppliers and government representatives, to discuss policies and procedures currently in place. Industry investment is being stimulated by the potential for biofuels and biochemicals, as well as the co-operation between the forest and energy sectors. The conference featured 23 presentations, of which 12 have been catalogued separately for inclusion in this database. refs., tabs., figs

Efeitos da purificação e do enriquecimento do creosoto vegetal na preservação da madeira de Eucalyptus grandis, após 48 meses de instalação do ensaio de campo Effects of the purification and enrichment of wood tar creosote on preservation of Eucalyptus grandis wood, after 48 months of field testing

Directory of Open Access Journals (Sweden)

Juarez Benigno Paes

2002-08-01

recovered at a temperature of 110-255 °C. A fraction of the distilled was washed with a solution of sodium bicarbonate at 9%, resulting in purified wood tar creosote (creosote 2. Creosotes 1 and 2 were enriched with 3% copper naphtenate; 3% zinc naphtenate; 3% of cobalt naphtenate; 2% TBTO; 2% tributil-tin tribromophenate; 2% pentachlorophenol; or 0.4% arsenic trioxide. Stakes of Eucalyptus grandis sapwood were treated by following the full cell process. The efficiency of wood tar creosote solutions was compared with that of coal tar creosote. The essay was established in three locations (Viçosa, Ponte Nova and Leopoldina -Minas Gerais, Brazil. The results showed that creosote 2 + pentaclorofenol was superior to creosotes 1 and 2 + TBTO, to creosotes 1 and 2 + zinc naftenato and to pure creosote 1, being similar to coal tar creosote. Creosote 2 was superior to creosote 1, only in Leopoldina. In general, the average life of untreated wood was between 12 and 24 months. The average life of wood treated with creosote 1 + TBTO was between 24 and 37 months, while that ofwood treated with creosote 1 + zinc naftenato, between 37 and 48 months and that of wood treated with creosote 1 + cobalt naftenato, pure creosote 2, creosote 2 + zinc naftenato or + TBTO was 48 months. At this stage of research it is not possible to estimate the treated wood average life, as compared with the other tested preservative solutions, it since 60% of the stakes did not break.

Vitrification technology for treating low-level waste from nuclear facilities

International Nuclear Information System (INIS)

Oniki, Toshiro; Nabemoto, Toyonobu; Fukui, Toshiki

2016-01-01

The development of technologies for treating nuclear waste generated by nuclear power plants and reprocessing plants during their operation or decommissioning is underway both in Japan and abroad. Of the many types of treatment technologies that have been developed, vitrification technology is attracting attention as being the most promising technology for converting such waste into a stable state. As a brief review of technical developments aimed at reducing nuclear waste and finding a solution to the final disposal issue, this paper describes approaches to completing the development of vitrification technology in Japan, including IHI's activities. (author)

Physical and chemical characterization of waste wood derived biochars.

Science.gov (United States)

Yargicoglu, Erin N; Sadasivam, Bala Yamini; Reddy, Krishna R; Spokas, Kurt

2015-02-01

Biochar, a solid byproduct generated during waste biomass pyrolysis or gasification in the absence (or near-absence) of oxygen, has recently garnered interest for both agricultural and environmental management purposes owing to its unique physicochemical properties. Favorable properties of biochar include its high surface area and porosity, and ability to adsorb a variety of compounds, including nutrients, organic contaminants, and some gases. Physical and chemical properties of biochars are dictated by the feedstock and production processes (pyrolysis or gasification temperature, conversion technology and pre- and post-treatment processes, if any), which vary widely across commercially produced biochars. In this study, several commercially available biochars derived from waste wood are characterized for physical and chemical properties that can signify their relevant environmental applications. Parameters characterized include: physical properties (particle size distribution, specific gravity, density, porosity, surface area), hydraulic properties (hydraulic conductivity and water holding capacity), and chemical and electrochemical properties (organic matter and organic carbon contents, pH, oxidation-reduction potential and electrical conductivity, zeta potential, carbon, nitrogen and hydrogen (CHN) elemental composition, polycyclic aromatic hydrocarbons (PAHs), heavy metals, and leachable PAHs and heavy metals). A wide range of fixed carbon (0-47.8%), volatile matter (28-74.1%), and ash contents (1.5-65.7%) were observed among tested biochars. A high variability in surface area (0.1-155.1g/m(2)) and PAH and heavy metal contents of the solid phase among commercially available biochars was also observed (0.7-83 mg kg(-1)), underscoring the importance of pre-screening biochars prior to application. Production conditions appear to dictate PAH content--with the highest PAHs observed in biochar produced via fast pyrolysis and lowest among the gasification

Development of a standardized reproduction toxicity test with the earthworm species Eisenia fetida andrei using copper, pentachlorophenol and 2,4-dichloroaniline

Energy Technology Data Exchange (ETDEWEB)

van Gestel, C.A.; van Dis, W.A.; van Breemen, E.M.; Sparenburg, P.M. (National Institute of Public Health and Environmental Protection, BA Bilthoven (Netherland))

1989-12-01

This article describes a standardized test method for determining the effect of chemical substances on the reproduction of the earthworm Eisenia fetida andrei. It is based on the existing guidelines for acute toxicity testing with earthworms, and for reasons of standardization the same artificial soil substrate and earthworm species were chosen as prescribed by these guidelines. After being preconditioned for one week in untreated soil, earthworms are exposed to the chemical substances for 3 weeks. The number of cocoons produced is determined, and cocoons are incubated in untreated artificial soil for 5 weeks to assess hatchability. Results are presented from toxicity experiments with pentachlorophenol, copper, and 2,4-dichloroaniline. For these compounds no-effect levels (NEL) for cocoon production were 32, 60-120, and 56 mg.kg-1 dry soil, respectively. Hatching of cocoons was influenced by pentachlorophenol (NEL, 10 mg.kg-1), but not by copper and dichloroaniline. Following exposure, earthworms were incubated in clean soil again to study the possibility of recovery of cocoon production. For copper and dichloroaniline earthworms did recover cocoon production to a level as high as the control level or even higher; in case of pentachlorophenol, cocoon production was still reduced after 3 weeks in clean soil.

Advances and challenges of wood polymer composites

Science.gov (United States)

Roger M. Rowell

2006-01-01

Wood flour and fiber have been blended with thermoplastic such as polyethylene, polypropylene, polylactic acid and polyvinyl chloride to form wood plastic composites (WPC). WPCs have seen a large growth in the United States in recent years mainly in the residential decking market with the removal of CCA treated wood decking from residential markets. While there are...

Specifications in the application form for environmental assessment of wood preservatives

Energy Technology Data Exchange (ETDEWEB)

Lucks, U J [ed.

2000-09-01

In 1990 the former Federal Health Office (Bundesgesundheitsamt) and the Federal Environmental Agency (Umweltbundesamt) jointly elaborated a catalogue of test requirements necessary for assessing the impact of wood preservatives on man and environment. Based on several years of experience, a revision was deemed necessary. Complying with the provisions of the Directive 98/8/EC of the European Parliament and the Council of 16 February 1998 concerning the placing of biocidal products on the market, which have to be transposed into national laws, the regulatory bodies BAM, BgVV and UBA, in cooperation with industry and academia (IUCT), developed an amended application form for wood preservatives. The provisions laid down there include different sets of data for wood preservatives, depending on the intended uses/hazard classes, e.g. physico-chemical and ecotoxicological properties, data on exposure, fate and behaviour in the environment and on waste management. The tests should be conducted according to standardized test protocols. Next to the list of data requirements explanations and justifications are given on why the data are needed and how they contribute to the risk assessment. Furthermore, recommendations are given on which test guidelines should preferably be followed to generate the data. In addition, annex I includes a proposal for a test guideline on how to screen leachates from preservative-treated wood surfaces for their ecotoxic potential to aquatic organisms. (orig.)

Superfund record of decision (EPA Region 3): Southern Maryland Wood Treating Site, Hollywood, MD, September 8, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The decision document presents the selected remedial action for the Southern Maryland Wood Treating Site (`the Site`), in Hollywood, Maryland. This is the second and final phase of remedial action for the Site. This phase addresses soil and sediment contamination and non-aqueous phase liquids (`NAPLs`) which are the principal threats remaining at the Site and are a source of contamination to the ground water and surface water.

40 CFR 60.3065 - What must I do if I plan to permanently close my air curtain incinerator that burns only wood...

Science.gov (United States)

2010-07-01

... close my air curtain incinerator that burns only wood waste, clean lumber, and yard waste and not... Compliance Times for Other Solid Waste Incineration Units That Commenced Construction On or Before December 9, 2004 Model Rule-Air Curtain Incinerators That Burn Only Wood Waste, Clean Lumber, and Yard Waste § 60...

Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler.

Science.gov (United States)

Samaras, P; Skodras, G; Sakellaropoulos, G P; Blumenstock, M; Schramm, K W; Kettrup, A

2001-01-01

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.

Selected mechanical properties of modified beech wood

Directory of Open Access Journals (Sweden)

Jiří Holan

2008-01-01

Full Text Available This thesis deals with an examination of mechanical properties of ammonia treated beach wood with a trademark Lignamon. For determination mechanical properties were used procedures especially based on ČSN. From the results is noticeable increased density of wood by 22% in comparison with untreated beach wood, which makes considerable increase of the most mechanical wood properties. Considering failure strength was raised by 32% and modulus of elasticity was raised at average about 46%.

What Next for Wood Construction/Demolition Debris?

OpenAIRE

Martin A. Hubbe

2014-01-01

Residents in localities throughout the world voluntarily participate in the routine recycling of household wastes, such as paper, metals, and plastics containers. But when a house in their neighborhood gets built or torn down, most of the debris – including wood waste – gets landfilled. Such a waste of material suggests that there are opportunities to add value to these under-utilized resources. The great variability, as well as contamination, pose major challenges. It is recommended that rec...

Treating nuclear waste

International Nuclear Information System (INIS)

Marriott, R.; Henyey, F.S.; Hochstim, A.R.

1984-01-01

A method of decreasing the amount of relatively long-lived fission products in radioactive waste materials comprises the steps of: separating relatively short-lived radioactive nuclides and stable nuclides from the waste material and storing at least some of them, exposing the remaining waste to a neutron flux in order to induce transmutations, separating the relatively short-lived radioactive nuclides and stable nuclides from the exposed materials and storing at least some of them, and repeating the exposure and separation steps

Urban wood: Fuel from landscapers and land fills

International Nuclear Information System (INIS)

Miles, T.R.; Miles, T.R. Jr.

1991-01-01

Wood recovered from urban landscaping, construction and building demolition has become an important fuel for several new power plants. Sources, composition, and requirements for fuel preparation, handling, firing and emissions control are described from experience at several plants. Urban wood waste fuels are suitable for steam and power generation if precautions are taken to process the fuel and provide uniform flow to the boiler

Control and treating technique of the nuclear wastes

International Nuclear Information System (INIS)

Ohira, Shigeru; Hayashi, Takumi

1997-01-01

In the large scale tritium treating and producing facilities such as ITER and others, they are presumed by absorbing, solving and diffusing tritium to various materials to be polluted instruments and equipments to become wastes by their partial or whole exchanges, recoveries, modifications, dismantlements and so forth. From a viewpoint of safety for the tritium, the following operations seem to be important among changing a part or whole of the objective instruments and equipments to wastes with finally disposable forms: to reduce the tritium remained volume as much as possible before the operations of exchange, dismantlement and so on, from viewpoint of risk reduction of the tritium emission into operation environment and outer environment; to reduce the tritium emission into the operation environment and circumference environment at operations of exchange, dismantlement and so on; to reduce the tritium leakage from the waste in storage and transportation before treatment; to protect the tritium pollution expansion at mechanical treatment processes such as cutting, pressing and so forth; and to reduce sufficiently the tritium concentration in the wastes to be disposed by proper treatment on a base of spirit of ALARA. (G.K.)

Comparative study of Nd:YAG laser-induced breakdown spectroscopy and transversely excited atmospheric CO2 laser-induced gas plasma spectroscopy on chromated copper arsenate preservative-treated wood.

Science.gov (United States)

Khumaeni, Ali; Lie, Zener Sukra; Niki, Hideaki; Lee, Yong Inn; Kurihara, Kazuyoshi; Wakasugi, Motoomi; Takahashi, Touru; Kagawa, Kiichiro

2012-03-01

Taking advantage of the specific characteristics of a transversely excited atmospheric (TEA) CO(2) laser, a sophisticated technique for the analysis of chromated copper arsenate (CCA) in wood samples has been developed. In this study, a CCA-treated wood sample with a dimension of 20 mm × 20 mm and a thickness of 2 mm was attached in contact to a nickel plate (20 mm × 20 mm × 0.15 mm), which functions as a subtarget. When the TEA CO(2) laser was successively irradiated onto the wood surface, a hole with a diameter of approximately 2.5 mm was produced inside the sample and the laser beam was directly impinged onto the metal subtarget. Strong and stable gas plasma with a very large diameter of approximately 10 mm was induced once the laser beam had directly struck the metal subtarget. This gas plasma then interacted with the fine particles of the sample inside the hole and finally the particles were effectively dissociated and excited in the gas plasma region. By using this technique, high precision and sensitive analysis of CCA-treated wood sample was realized. A linear calibration curve of Cr was successfully made using the CCA-treated wood sample. The detection limits of Cr, Cu, and As were estimated to be approximately 1, 2, and 15 mg/kg, respectively. In the case of standard LIBS using the Nd:YAG laser, the analytical intensities fluctuate and the detection limit was much lower at approximately one-tenth that of TEA CO(2) laser. © 2012 Optical Society of America

Production of Solid Fuel Briquettes from Agricultural and Wood ...

African Journals Online (AJOL)

Fibrous agricultural and wood waste materials have been compressed with suitable adhesive into solid fuel briquettes in a compressing machine, which was designed and constructed for this purpose. Nine samples of fibrous waste materials were prepared into different categories:- Category A (100% saw-dust, 100% ...

Recycling of wood for particle board production: accounting of greenhouse gases and global warming contributions

DEFF Research Database (Denmark)

Merrild, Hanna Kristina; Christensen, Thomas Højlund

2009-01-01

of virgin wood does not change the results radically (—665 to —125 kg CO2-equivalents tonne— 1 wood waste). However, if in addition it is assumed that the GHG emissions from combustion of wood has no global warming potential (GWP) and that the energy produced from excess wood due to recycling substitutes...

Wood biomass gasification in the world today

International Nuclear Information System (INIS)

Nikolikj, Ognjen; Perishikj, Radovan; Mikulikj, Jurica

1999-01-01

Today gasification technology of different kinds represents a more and more interesting option of the production of energy forms. The article describes a biomass gasification plant (waste wood) Sydkraft, Vernamo from Sweden. (Author)

Wood-energy - The sector get worried

International Nuclear Information System (INIS)

Mary, Olivier; Signoret, Stephane; Bohlinger, Philippe; Guilhem, Jean; De Santis, Audrey; Sredojevic, Alexandre; Defaye, Serge; Maindrault, Marc

2017-01-01

Wood energy is, today and certainly also tomorrow, one of the most important renewable energies in France. However, the wood-energy sector seems to slow down as hydrocarbon prices stay extremely low. This document presents 8 articles, describing the context and the characteristics of this evolution, plus some examples of developments in France. The themes of the articles are: the activity of the wood-energy sector should be reinforced to meet the objectives of the French energy multi-year plan; The 2035 prospective of the wood yield in the French forest will meet the future demand, however this evaluation does not take into consideration the effects of the climatic change; the conversion to biomass of the 'Fort de l'Est' (near Paris) heating system (equipped with a boiling fluidized bed boiler) has enabled the heat network to beat the 50 pc share of renewable energy; wood-energy professionals use the 'quality' lever to challenge their fossil fuel competitors; the city of Orleans is now equipped with an innovative biomass cogeneration plant; the example of wood waste valorization in a French sawmill; the French ONF (Forest Administration) Wood-Energy actor has just inaugurated its largest biomass dryer, in order to develop the domestic market for wood as a fuel; analysis of the technical and economical feasibility of using wood to generate electric power or replacing electric space heating by heat network

Hot water extracted wood fiber for production of wood plastic composites (WPCs)

Science.gov (United States)

Manuel Raul Pelaez-Samaniego; Vikram Yadama; Eini Lowell; Thomas E. Amidon; Timothy L. Chaffee

2013-01-01

Undebarked ponderosa pine chips were treated by hot water extraction to modify the chemical composition. In the treated pine (TP) , the mass was reduced by approximately 20%, and the extract was composed mainly of degradation products of hemicelluloses. Wood flour produced from TP and unextracted chips (untreated pine, UP) was blended with high-density polyethylene (...

Exploring the role of wood waste landfills in early detection of non-native alien wood-boring beetles

Science.gov (United States)

Davide Rassati; Massimo Faccoli; Lorenzo Marini; Robert A. Haack; Andrea Battisti; Edoardo. Petrucco Toffolo

2015-01-01

Non-native wood-boring beetles (Coleoptera) represent one of the most commonly intercepted groups of insects at ports worldwide. The development of early detection methods is a crucial step when implementing rapid response programs so that non-native wood-boring beetles can be quickly detected and a timely action plan can be produced. However, due to the limited...

Controversy. The wood war; Polemique - la guerre du bois

Energy Technology Data Exchange (ETDEWEB)

James, O.

2010-12-15

The author comments the conflict emerging in France between industries exploiting wood for construction and those exploiting it as a heating material for power generation. The first ones accuse the others to steal their raw material, to pull the prices up, and to destabilize the sector. This conflict takes place notably around sawmill wastes which are used either by wood panel fabricators or by wood pellets producers. Both sectors are claiming they are creating more jobs than the other. The French forest indeed offers good opportunities for both sectors, but other countries which are lacking forest surfaces, are buying wood in France. Several issues are matter of discussion: burning wood seems to go against the reduction of greenhouse gas emissions, subsidies awarded to big heater projects. The situation of the wood sector in Austria, Finland and Poland is briefly presented

Utilization of poplar wood sawdust for heavy metals removal from model solutions

Directory of Open Access Journals (Sweden)

Demcak Stefan

2017-06-01

Full Text Available Some kinds of natural organic materials have a potential for removal of heavy metal ions from wastewater. It is well known that cellulosic waste materials or by-products can be used as cheap adsorbents in chemical treatment process. In this paper, poplar wood sawdust were used for removal of Cu(II, Zn(II and Fe(II ions from model solutions with using the static and dynamic adsorption experiments. Infrared spectrometry of poplar wood sawdust confirmed the presence of the functional groups which correspond with hemicelluloses, cellulose and lignin. At static adsorption was achieved approximately of 80 % efficiency for all treated model solutions. Similar efficiency of the adsorption processes was reached after 5 min at dynamic condition. The highest efficiency of Cu(II removal (98 % was observed after 30 min of dynamic adsorption. Changes of pH values confirmed a mechanism of ion exchange on the beginning of the adsorption process.

EFFECT OF ARTIFICIAL WEATHERING ON WOOD LAMINATES COLOR TREATED WITH TWO FINISHING PRODUCTS

Directory of Open Access Journals (Sweden)

Thais Jacob Mendes

2016-03-01

Full Text Available Weathering is one of the main reasons for the degradation of wood, especially its color. The application of finishes minimizes these effects. This study aimed to monitor the effect of artificial weathering on wood veneer of the species cumaru (Dipteryx odorata and pau marfim (Balfourodendron riedelianum with two finishes, the marine varnish and Cetol, with monitoring using a spectrophotometer. The samples were subjected to cycles of exposure to weathering for 20, 40, 52, 76, 124, 226, 430, 838 and 960 hours. The colorimetric parameters (L*, a*, b*, C and h* were measured before treatment, after application of the products and during the weathering time intervals. The application of finishes darkened veneer of cumaru wood and pau marfim in nature. However, in higher weathering times, both species returned to a lighter color, and even became lighter than the natural wood. The use of Cetol was more efficient, giving greater stability in the conservation of wood color of the species studied.

Hexadecyl ammonium chloride amylose inclusion complex to emulsify cedarwood oil and treat wood against termites and wood-decay fungi

Science.gov (United States)

F.J. Eller; W.T. Hay; G.T. Kirker; M.E. Mankowski; G.W. Sellling

2018-01-01

Cedarwood oil (CWO) has a wide range of bioactivities, including insect repellency and toxicity, as well as conferring resistance against termites and wood-decay fungi. In previous work examining pressure treatment of wood, ethanol was used as the diluent/carrier for CWO. However, it is preferable to use a water-based carrier for environmental, safety and cost...

Quaternized wood as sorbent for hexavalent chromium.

Science.gov (United States)

Low, K S; Lee, C K; Lee, C Y

2001-01-01

The potential of quaternized wood (QW) chips in removing hexavalent chromium from synthetic solution and chrome waste under both batch and continuous-flow conditions was investigated. Sorption was found to be dependent on pH, metal concentration, and temperature. QW chips provide higher sorption capacity and wider pH range compared with untreated wood chips. The equilibrium data could be fitted into the Langmuir isotherm model, and maximum sorption capacities were calculated to be 27.03 and 25.77 mg/g in synthetic chromate solution and chrome waste, respectively. The presence of sulfate in high concentration appeared to suppress the uptake of chromium by QW chips. Column studies showed that bed depth influenced the breakthrough time greatly whereas flow rate of influent had little effect on its sorption on the column.

Harvested wood products : basis for future methodological development

Science.gov (United States)

Kenneth E. Skog

2003-01-01

The IPCC Guidelines (IPCC 1997) provide an outline of how harvested wood could be treated in national greenhouse gas (GHG) inventories. This section shows the relation of that outline to the approaches and estimation methods to be presented in this Appendix. Wood and paper products are referred to as harvested wood products (HWP). It does not include carbon in...

Chapter 23: Corrosion of Metals in Wood Products

Science.gov (United States)

Samuel L. Zelinka

2014-01-01

The corrosion of metals in contact with wood has been studied for over 80 years, and in most situations wood is not corrosive [1]. Recently, however, the durability of fasteners in preservative--treated wood has become a concern. Changes in legislation and certification in the United States, the European Union, and Australasia have restricted the use of chromated...

In Situ Gamma Irradiation and Thermal Treatment Effects on the Static Bending Properties of Particle boards Based on Waste Materials and Different Adhesives

International Nuclear Information System (INIS)

Khafaga, M.R.; El-Naggar, A.M.; Zahran, A.H.; Kandeel, K.A.

2000-01-01

Particle boards based on different waste materials and different polymers as adhesives have been prepared by compression molding in a hot press at 120 degree and constant pressure. The used waste materials were cotton stalks, flax stalks and wood saw-dust whereas urea formaldehyde (UF), polystyrene (PS) and the epoxy resins 103 (E 103) and 150 (E 150) were used as adhesives. The thermally treated particleboard woods were subsequently exposed to gamma radiation. The static bending parameters of the different factors that may affect the mechanical properties such as irradiation dose, time of thermal treatment and adhesive content were also investigated. In general it was found that the highest mechanical properties of the unirradiated woods were obtained when the preparation was carried out under hot press for 20 min and the adhesive content was 20 wt.% (based on weight of waste material). The obtained results showed that the mechanical properties were greatly increased with increasing irradiation dose from 3 to 5 Mrad. Meanwhile, particleboard based on cotton or flax stalks and the epoxy resins 103 and 150 displayed higher mechanical properties than these based on wood saw-dust and the same adhesives

Development of METHANE de-NOX Reburn Process for Wood Waste and Biomass Fired Stoker Boilers - Final Report - METHANE de-NOX Reburn Technology Manual

Energy Technology Data Exchange (ETDEWEB)

J. Rabovitser; B. Bryan; S. Wohadlo; S. Nester; J. Vaught; M. Tartan (Gas Technology Institute); R. Glickert (ESA Environmental Solutions)

2007-12-31

The overall objective of this project was to demonstrate the effectiveness of the METHANE de-NOX® (MdN) Reburn process in the Forest Products Industry (FPI) to provide more efficient use of wood and sludge waste (biosolids) combustion for both energy generation and emissions reduction (specifically from nitrogen oxides (NOx)) and to promote the transfer of the technology to the wide range of wood waste-fired stoker boilers populating the FPI. This document, MdN Reburn Commercial Technology Manual, was prepared to be a resource to promote technology transfer and commercialization activities of MdN in the industry and to assist potential users understand its application and installation requirements. The Manual includes a compilation of MdN commercial design data from four different stoker boiler designs that were baseline tested as part of the development effort. Design information in the Manual include boiler CFD model studies, process design protocols, engineering data sheets and commercial installation drawings. Each design package is unique and implemented in a manner to meet specific mill requirements.

Eucalyptus grandis AND Eucalyptus dunnii USE FOR WOOD-CEMENT PANELS MANUFACTURING

Directory of Open Access Journals (Sweden)

Setsuo Iwakiri

2008-03-01

Full Text Available This research evaluated the potential use of Eucalyptus grandis and Eucalyptus dunnii wood for wood-cement panelsmanufacturing. The boards were manufactured at the density of 1,20 g/cm³, using portland cement as mineral bonding and woodfurnish without treatment, treated in cold water and hot water. The wood furnish of Pinus taeda was used as control. The resultsindicated that it is not necessary to treat E. grandis and E. dunni wood for wood-cement board manufacturing. In relation to woodspecies, the board manufactured with E. dunnii showed lower values of mechanical properties. However, boards manufactured of E.grandis wood showed satisfactory results in comparison to boards of P. taeda and the referenced values of BISON process and otherproducts cited in the pertnent literature, indicating the high potential for wood-cement board manufacture of this tree species.

Elastic and Strength Properties of Heat-Treated Beech and Birch Wood

Directory of Open Access Journals (Sweden)

Vlastimil Borůvka

2018-04-01

Full Text Available This paper deals with the impact of heat treatment on the elastic and strength properties of two diffuse porous hardwoods, namely Fagus sylvatica and Betula pendula. Two degrees of the heat treatment were used at temperatures of 165 °C and 210 °C. The dynamic and static elasticity modulus, bending strength, impact toughness, hardness, and density were tested. It is already known that an increase in treatment temperature decreases the mechanical properties and, on the other hand, leads to a better shape and dimensional stability. Higher temperatures of the heat treatment correlated with lower elastic and strength properties. In the case of higher temperature treatments, the decline of tested properties was noticeable as a result of serious changes in the chemical composition of wood. It was confirmed that at higher temperature stages of treatment, there was a more pronounced decrease in beech properties compared to those of the birch, which was the most evident in their bending strength and hardness. Our research confirmed that there is no reason to consider birch wood to be of a lesser quality, although it is regarded by foresters as an inferior tree species. After the heat treatment, the wood properties are almost the same as in the case of beech wood.

Potential availability of urban wood biomass in Michigan: Implications for energy production, carbon sequestration and sustainable forest management in the U.S.A

International Nuclear Information System (INIS)

MacFarlane, David W.

2009-01-01

Tree and wood biomass from urban areas is a potentially large, underutilized resource viewed in the broader social context of biomass production and utilization. Here, data and analysis from a regional study in a 13-county area of Michigan, U.S.A. are combined with data and analysis from several other studies to examine this potential. The results suggest that urban trees and wood waste offer a modest amount of biomass that could contribute significantly more to regional and national bio-economies than it does at present. Better utilization of biomass from urban trees and wood waste could offer new sources of locally generated wood products and bio-based fuels for power and heat generation, reduce fossil fuel consumption, reduce waste disposal costs and reduce pressure on forests. Although wood biomass generally constitutes a 'carbon-neutral' fuel, burning rather than burying urban wood waste may not have a net positive effect on reducing atmospheric CO 2 levels, because it may reduce a significant long term carbon storage pool. Using urban wood residues for wood products may provide the best balance of economic and environmental values for utilization

Plant uptake of pentachlorophenol from sludge-amended soils

International Nuclear Information System (INIS)

Bellin, C.A.; O'Connor, G.A.

1990-01-01

A greenhouse study was conducted to determine the effects of sludge on plant uptake of 14 C-pentachlorophenol (PCP). Plants included tall fescue (Festuca arundinacea Schreb.), lettuce (Latuca sativa L.), carrot (Daucus carota L.), and chile pepper (Capsicum annum L.). Minimal intact PCP was detected in the fescue and lettuce by gas chromatography/mass spectrometry (GC/MS) analysis. No intact PCP was detected in the carrot tissue extracts. Chile pepper was not analyzed for intact PCP because methylene chloride extracts contained minimal 14 C. The GC/MS analysis of soil extracts at harvest suggests a half-life of PCP of about 10 d independent of sludge rate or PCP loading rate. Rapid degradation of PCP in the soil apparently limited PCP availability to the plant. Bioconcentration factors (dry plant wt./initial soil PCP concentration) based on intact PCP were < 0.01 for all crops, suggesting little PCP uptake. Thus, food-chain crop PCP uptake in these alkaline soils should not limit land application of sludge

Sawmill "Waste"

Science.gov (United States)

Fred C. Simmons; Adna R. Bond

1955-01-01

Sawmills have the reputation of being very wasteful in converting logs and bolts into lumber and timbers. Almost everyone has seen the great heaps of sawdust and slabs that collect at sawmills. Frequently the question is asked, "Why doesn't somebody do something about this terrible waste of wood?"

Report of the Task Force on Sawmill Wood Residue Management

International Nuclear Information System (INIS)

1993-11-01

The Sawmill Wood Residue Task Force was established in 1993 to seek solutions to managing wood residue at sawmills, shingle mills, and log sort yards in British Columbia without burning or landfilling. In particular, the Task Force was formed to address the phaseout of beehive-type wood waste burners by January 1, 1996. The Task Force was formed at the forest product industry's request and included representatives from industry associations and government. It reviewed existing information on the quantities of mill residues and the options available for reducing, reusing, and recycling the residues. Nearly half of all the province's residues of 5 million bone dry tonnes/y is disposed of by burning with no energy recovery, or by landfilling. It was recognized that the total volume of wood residue cannot be handled by any one method suitable for all sources but that in the near term, electricity generation could deal with a significant percentage of wood currently being burned. The most immediate technically viable opportnity by industry in this area may be in cogeneration of electricity for load displacement at pulp mills. Other opportunities exist such as conversion of wood residue to liquid fuels but these require greater commitments to research and development. The need to handle bark and sawdust was identified as a critical requirement for alternate uses. Small niche uses for wood residue must be examined on a case by case basis for each company or group of companies in a region. The provincial government can also promote better use of wood wastes through policies such as social costing of power generation options and sales tax exemption for ethanol fuel. 1 tab

Monitoring losses of copper based wood preservatives in the Thames estuary

International Nuclear Information System (INIS)

Hingston, J.A.; Murphy, R.J.; Lester, J.N.

2006-01-01

Field trials were conducted at two sites in the Thames estuary to monitor losses of copper, chromium and arsenic from wood preservative treated timbers of varying sizes and treatment regimes. Results indicated that leaching tests conducted under standard laboratory conditions might overestimate losses compared to losses resulting from real environmental exposures. Amine copper treated wood was noted to leach higher levels of copper compared to chromated copper arsenate treated wood, and was therefore considered an inappropriate replacement biocide for fresh and marine construction purposes on this basis. Increases in copper concentrations in the outer sections of amine copper treated posts may have represented re-distribution of this component in this timber. No accumulation of metals was found in sediments surrounding field trial posts. - Wood preservative field trials in the UK indicate that standard laboratory tests overestimate losses compared to those resulting from real environmental exposures

Monitoring losses of copper based wood preservatives in the Thames estuary

Energy Technology Data Exchange (ETDEWEB)

Hingston, J.A. [Environmental Processes and Water Technology Research Group, Department of Environmental Science and Technology, Faculty of Life Sciences, Imperial College, London SW7 2AZ (United Kingdom)]. E-mail: james.hingston@psd.defra.gsi.gov.uk; Murphy, R.J. [Department of Biology, Imperial College, London SW7 2AZ (United Kingdom); Lester, J.N. [School of Water Sciences, Cranfield University, Cranfield, Bedfordshire, MK43 0AL (United Kingdom)

2006-09-15

Field trials were conducted at two sites in the Thames estuary to monitor losses of copper, chromium and arsenic from wood preservative treated timbers of varying sizes and treatment regimes. Results indicated that leaching tests conducted under standard laboratory conditions might overestimate losses compared to losses resulting from real environmental exposures. Amine copper treated wood was noted to leach higher levels of copper compared to chromated copper arsenate treated wood, and was therefore considered an inappropriate replacement biocide for fresh and marine construction purposes on this basis. Increases in copper concentrations in the outer sections of amine copper treated posts may have represented re-distribution of this component in this timber. No accumulation of metals was found in sediments surrounding field trial posts. - Wood preservative field trials in the UK indicate that standard laboratory tests overestimate losses compared to those resulting from real environmental exposures.

Other Special Waste

DEFF Research Database (Denmark)

Brogaard, Line Kai-Sørensen; Christensen, Thomas Højlund

2011-01-01

In addition to the main types of special waste related to municipal solid waste (MSW) mentioned in the previous chapters (health care risk waste, WEEE, impregnated wood, hazardous waste) a range of other fractions of waste have in some countries been defined as special waste that must be handled...... separately from MSW. Some of these other special wastes are briefly described in this chapter with respect to their definition, quantity and composition, and management options. The special wastes mentioned here are batteries, tires, polyvinylchloride (PVC) and food waste....

Effects of compost and phosphate on plant arsenic accumulation from soils near pressure-treated wood

International Nuclear Information System (INIS)

Cao Xinde; Ma, Lena Q.

2004-01-01

Leaching of arsenic (As) from chromated copper arsenate (CCA)-treated wood may elevate soil arsenic levels. Thus, an environmental concern arises regarding accumulation of As in vegetables grown in these soils. In this study, a greenhouse experiment was conducted to evaluate As accumulation by vegetables from the soils adjacent to the CCA-treated utility poles and fences and examine the effects of soil amendments on plant As accumulation. Carrot (Daucus carota L.) and lettuce (Lactuca sativa L.) were grown for ten weeks in the soil with or without compost and phosphate amendments. As expected, elevated As concentrations were observed in the pole soil (43 mg kg -1 ) and in the fence soil (27 mg kg -1 ), resulting in enhanced As accumulation of 44 mg kg -1 in carrot and 32 mg kg -1 in lettuce. Addition of phosphate to soils increased As accumulation by 4.56-9.3 times for carrot and 2.45-10.1 for lettuce due to increased soil water-soluble As via replacement of arsenate by phosphate in soil. However, biosolid compost application significantly reduced plant As uptake by 79-86%, relative to the untreated soils. This suppression is possibly because of As adsorbed by biosolid organic mater, which reduced As phytoavailability. Fractionation analysis showed that biosolid decreased As in soil water-soluble, exchangeable, and carbonate fraction by 45%, whereas phosphate increased it up to 2.61 times, compared to the untreated soils. Our results indicate that growing vegetables in soils near CCA-treated wood may pose a risk of As exposure for humans. Compost amendment can reduce such a risk by reducing As accumulation by vegetables and can be an important strategy for remediating CCA-contaminated soils. Caution should be taken for phosphate application since it enhances As accumulation. - Capsule: Compost amendment can reduce As exposure risk for humans by reducing As accumulation by vegetables and can be an important strategy for remediating CCA-contaminated soils

Effects of compost and phosphate on plant arsenic accumulation from soils near pressure-treated wood

Energy Technology Data Exchange (ETDEWEB)

Cao Xinde [Soil and Water Science Department, University of Florida, Gainesville, FL (United States)]. E-mail: xcao@stevens.edu; Ma, Lena Q. [Soil and Water Science Department, University of Florida, Gainesville, FL (United States)

2004-12-01

Leaching of arsenic (As) from chromated copper arsenate (CCA)-treated wood may elevate soil arsenic levels. Thus, an environmental concern arises regarding accumulation of As in vegetables grown in these soils. In this study, a greenhouse experiment was conducted to evaluate As accumulation by vegetables from the soils adjacent to the CCA-treated utility poles and fences and examine the effects of soil amendments on plant As accumulation. Carrot (Daucus carota L.) and lettuce (Lactuca sativa L.) were grown for ten weeks in the soil with or without compost and phosphate amendments. As expected, elevated As concentrations were observed in the pole soil (43 mg kg{sup -1}) and in the fence soil (27 mg kg{sup -1}), resulting in enhanced As accumulation of 44 mg kg{sup -1} in carrot and 32 mg kg{sup -1} in lettuce. Addition of phosphate to soils increased As accumulation by 4.56-9.3 times for carrot and 2.45-10.1 for lettuce due to increased soil water-soluble As via replacement of arsenate by phosphate in soil. However, biosolid compost application significantly reduced plant As uptake by 79-86%, relative to the untreated soils. This suppression is possibly because of As adsorbed by biosolid organic mater, which reduced As phytoavailability. Fractionation analysis showed that biosolid decreased As in soil water-soluble, exchangeable, and carbonate fraction by 45%, whereas phosphate increased it up to 2.61 times, compared to the untreated soils. Our results indicate that growing vegetables in soils near CCA-treated wood may pose a risk of As exposure for humans. Compost amendment can reduce such a risk by reducing As accumulation by vegetables and can be an important strategy for remediating CCA-contaminated soils. Caution should be taken for phosphate application since it enhances As accumulation. - Capsule: Compost amendment can reduce As exposure risk for humans by reducing As accumulation by vegetables and can be an important strategy for remediating CCA

Federal tax incentives and disincentives for the adoption of wood-fuel electric-generating technologies

International Nuclear Information System (INIS)

Hill, L.J.; Hadley, S.W.

1995-01-01

In this paper, we estimate the effects of current federal tax policy on the financial criteria that investor-owned electric utilities (IOUs) and non-utility electricity generators (NUGs) use to evaluate wood-fuel electric-generating technologies, distinguishing between dedicated-plantation and wood-waste fuels. Accelerated tax depreciation, the 1.5 cent/kWh production tax credit for the dedicated-plantation technology, and the alternative minimum tax are the most important tax provisions. The results indicate that federal tax laws have significantly different effects on the evaluation criteria, depending on the plant's ownership (IOU vs NUG) and type of fuel (dedicated-plantation vs wood-waste). (Author)

Environmental education on wood preservatives and preservative ...

African Journals Online (AJOL)

The development and use of wood preservatives in Nigeria should address not only the cost and demand functions but also the potential hazards in environmental equations. Forest products specialists are often asked about the perceived risks and environmental costs of treated wood products. Evidently, the civil society is ...

Methods for Mitigating the Environmental Risks Associated with Wood Preservatives

Science.gov (United States)

Dennis Hayward; Stan T. Lebow; Kenneth M. Brooks

2011-01-01

As noted in earlier chapters, the treatment of wood is both art and science. Wood is a variable material; treatment results tend to vary with the preservative and wood species and even within boards of the same species. This means that treated wood often contains a range of preservative retentions. Some pieces will have less than the desired retention, while others may...

THERMAL DEGRADATION AND MORPHOLOGICAL ASPECTS OF FOUR WOOD SPECIES USED IN LUMBER INDUSTRY

Directory of Open Access Journals (Sweden)

Matheus Poletto

Full Text Available ABSTRACT The aim of this work was characterize four wood waste samples from lumber industry in order to obtain previous information about structure and properties of wood before use it as a biofuel or as reinforcement in composite formulations. The influence of wood components on the thermal degradation stability of different wood species has been investigated using thermogravimetry, differential scanning calorimetry and scanning electron microscopy. Four wood species, Eucalyptus grandis (EUG, Pinus elliottii (PIE, Dipteryx odorata (DIP and Mezilaurus itauba (ITA, were used in this study. The results showed that higher extractives contents may form a thin film on the wood fiber surface which can accelerate the degradation process and reduce the wood thermal stability

Degradation of pentachlorophenol by the white rot fungus Phanerochaete chrysosporium grown in ammonium lignosulphonate media.

Science.gov (United States)

Aiken, B S; Logan, B E

1996-06-01

Removal and degradation of pentachlorophenol (PCP) by Phanerochaete chrysosporium in static flask cultures was studied using ammonium lignosulphonates (LS), a waste product of the papermill industry, as a carbon and nitrogen source. After 3 days, cultures of P. chrysosporium grown in either a 2% LS (nitrogen-sufficient) medium or a 0.23% LS and 2% glucose (nitrogen-deficient) medium removed 72 to 75% of PCP, slightly less than the 95% removal seen using nitrogen-deficient glucose and ammonia medium. PCP dehalogenation occurred despite the fact that extracellular enzyme (LiP) activity, measured by a veratryl alcohol oxidation assay and by PCP disappearance in cell-free extracts, was inhibited by LS. This inactivation of LiP likely contributed to the lower percent of PCP dehalogenation observed using the LS media. In order to better understand the relationship between PCP disappearance and dehalogenation, we measured the fate of the chlorine in PCP. After 13 days, only 1.8% of the initial PCP added was recoverable as PCP. The remainder of the PCP was either mineralized or transformed to breakdown intermediates collectively identified as organic halides. The largest fraction of the original chlorine (58%) was recovered as organic (non-PCP) halide, most of which (73%) was associated with the cell mass. Of the remaining chlorine, 40% was released as chloride ion, indicating a level of dehalogenation in agreement with previously reported values.

Jackfruit (Artocarpus heterophyllus lamk) wood waste as a textile natural dye by micowave-assisted extraction method

Science.gov (United States)

Qadariyah, Lailatul; Gala, Selfina; Widoretno, Dhaniar Rulandri; Kunhermanti, Delita; Bhuana, Donny S.; Sumarno, Mahfud, Mahfud

2017-05-01

The development of technology causes most of textile industries in Indonesia prefer to use synthetic dyes in the fabric dyeing process. In fact, synthetic dyes is able to have negative effect since it is is toxic to the health of workers and environment. To resolve this issues, one way to do is to use natural dyes. One of untapped potential in Indonesia is wood waste of jackfruit from furniture industry. Jackfruit wood itself containing dyestuffs which gives yellow color pigment so that it can be used as an alternative source of natural dyes. The purpose of this research is to study the effect of extraction time, mass to solvent volume ratio, and microwave power to yield of dyes. The extract of dye analyzed by UV-Visible Spectrophotometer and GC-MS, along the coloring and endurance tests of natural dyes on fabric and compare it with synthetic dyes. In this research, material is going to be extracted is the wood of jackfruit (Artocarpus heterophyllus lamk) with material size between 35 mesh - 60 mesh. The extraction process is done by using ethanol 96%. Extraction using MAE is carried out at the ratio of materials to solvent of 0,02-0,1 g/mL, the microwave power of 100-800 Watt, and the extraction time of 10-90 minutes. The conclusion is at microwave power of 400 Watt, material to solvent ratio of the 0,02 g/mL, the yield is 3,39% while at microwave power of 600 Watt, material to solvent ratio of the 0,02 g/mL, the yield is 3,67% with extraction time of 30 minutes. The highest recovery from ethanol 96% solvent is 60,41%. The result of UV-Vis Spectrophotometry and GC-MS test show that there is a chromophore compound in the extract of natural dye. The test results show the natural dyes of jackfruit wood can be used to coloring on the textile because it can gives staining result permanently.

Online elemental analysis of process gases with ICP-OES: A case study on waste wood combustion

International Nuclear Information System (INIS)

Wellinger, Marco; Wochele, Joerg; Biollaz, Serge M.A.; Ludwig, Christian

2012-01-01

Highlights: ► Simultaneous measurements of 23 elements in process gases of a waste wood combustor. ► Mobile ICP spectrometer allows measurements of high quality at industrial plants. ► Continuous online measurements with high temporal resolution. ► Linear correlations among element concentrations in the raw flue gas were detected. ► Novel sampling and calibration methods for ICP-OES analysis of process gases. - Abstract: A mobile sampling and measurement system for the analysis of gaseous and liquid samples in the field was developed. An inductively coupled plasma optical emission spectrometer (ICP-OES), which is built into a van, was used as detector. The analytical system was calibrated with liquid and/or gaseous standards. It was shown that identical mass flows of either gaseous or liquid standards resulted in identical ICP-OES signal intensities. In a field measurement campaign trace and minor elements in the raw flue gas of a waste wood combustor were monitored. Sampling was performed with a highly transport efficient liquid quench system, which allowed to observe temporal variations in the elemental process gas composition. After a change in feedstock an immediate change of the element concentrations in the flue gas was detected. A comparison of the average element concentrations during the combustion of the two feedstocks showed a high reproducibility for matrix elements that are expected to be present in similar concentrations. On the other hand elements that showed strong differences in their concentration in the feedstock were also represented by a higher concentration in the flue gas. Following the temporal variations of different elements revealed strong correlations between a number of elements, such as chlorine with sodium, potassium and zinc, as well as arsenic with lead, and calcium with strontium.

Cellulose Nanocomposites by Melt Compounding of TEMPO-Treated Wood Fibers in Thermoplastic Starch Matrix

Directory of Open Access Journals (Sweden)

Aline Cobut

2014-04-01

Full Text Available To facilitate melt compounding of cellulose nanofibrils (CNF based composites, wood pulp fibers were subjected to a chemical treatment whereby the fibers were oxidized using 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO. This treatment introduced negatively charged carboxylate groups to the fibers. TEMPO-treated fibers (TempoF were added to a mixture of amylopectin starch, glycerol, and water. Granules were prepared from this mixture and processed into CNF composites by extrusion. TempoF were easier to process into composites as compared with non-treated pulp fibers (PF. SEM revealed partial disintegration of TempoF during melt processing. Consequently, TempoF gave composites with much better mechanical properties than those of conventional composites prepared from pulp fibers and TPS. Particularly, at 20 wt% TempoF content in the composite, the modulus and strength were much improved. Such a continuous melt processing route, as an alternative to laboratory solvent casting techniques, may promote large-scale production of CNF-based composites as an environmentally friendly alternative to synthetic plastics/composites.

Radiation processing of wood-plastic composites

International Nuclear Information System (INIS)

Czvikovszky, T.

1992-01-01

There are three main types of radiation-processed composite material derived from plastics and fibrous natural polymers. The first are the monomer-impregnated, radiation-treated wood-plastic composites (WPC). They became a commercial success in the early 1970s. More recently, work has focused on improving the WPCs by creating in them interpenetrating network (IPN) systems by the use of appropriate multifunctional oligomers and monomers. The main kinetic features of radiation-initiated chain polymerization remain applicable even in impregnated wood. The second type are the plastics filled or reinforced with dispersed wood fiber or other cellulosics (WFRP). In their case, radiation processing offers a new opportunity to apply radiation-reactive adhesion promoters between wood or cellulosic fibers and the thermoplastic matrices. The third type are the laminar composites made by electron beam coating of wood-based agglomerate sheets and boards. This chapter reviews the industrial applications and the radiation processing of the three types of the wood-plastic composites and indicates future trends. (orig.)

Discover the benefits of residential wood heating

International Nuclear Information System (INIS)

2003-01-01

This publication described how residential wood-heating systems are being used to reduce energy costs and increase home comfort. Biomass energy refers to all forms are renewable energy that is derived from plant materials. The source of fuel may include sawmills, woodworking shops, forest operations and farms. The combustion of biomass is also considered to be carbon dioxide neutral, and is not considered to be a major producer of greenhouse gases (GHG) linked to global climate change. Wood burning does, however, release air pollutants, particularly if they are incompletely burned. Incomplete combustion of wood results in dense smoke consisting of toxic gases. Natural Resources Canada helped create new safety standards and the development of the Wood Energy Technical Training Program to ensure that all types of wood-burning appliances are installed correctly and safely to reduce the risk of fire and for effective wood heating. In Canada, more than 3 million families heat with wood as a primary or secondary heating source in homes and cottages. Wood heating offers security from energy price fluctuations and electrical power failures. This paper described the benefits of fireplace inserts that can transform old fireplaces into modern heating systems. It also demonstrated how an add-on wood furnace can be installed next to oil furnaces to convert an oil-only heating system to a wood-oil combination system, thereby saving thousands of dollars in heating costs. Wood pellet stoves are another wood burning option. The fuel for the stoves is produced from dried, finely ground wood waste that is compressed into hard pellets that are loaded into a hopper. The stove can run automatically for up to 24 hours. New high-efficiency advanced fireplaces also offer an alternative heating system that can reduce heating costs while preserving Canada's limited supply of fossil fuels such as oil and gas. 13 figs

Wood energy and air quality. Synthetic report

International Nuclear Information System (INIS)

2009-07-01

This report presents and comments some reference data about the current and prospective (2010, 2020) pollutant emissions through wood combustion as a source of energy. It indicates and compares greenhouse gas emissions by the different sources for household, collective and industrial heating (fuel, gas, electricity, pellets, logs, grinds, wood wastes), gives an overview of atmospheric emissions due to biomass combustion. It compares emissions due to wood combustion with respect to the activity sectors and to combustion equipment. It highlights the challenges of the development of the household sector in terms of improvement and renewal of the quality of the burning equipment. It comments the implemented policies which notably aim at reducing the emission of particles, and at defining quality labels

Enhanced selection of micro-aerobic pentachlorophenol degrading granular sludge

Energy Technology Data Exchange (ETDEWEB)

Lv, Yuancai, E-mail: donkey1204@hotmail.com [State Key Laboratory of Pulp and Paper Engineering, College of Light Industry and Food Science, South China University of Technology, Guangzhou 510640 (China); Chen, Yuancai, E-mail: chenyc@scut.edu.cn [State Key Laboratory of Pulp and Paper Engineering, College of Light Industry and Food Science, South China University of Technology, Guangzhou 510640 (China); Ministry of Education Key Laboratory of Pollution Control and Ecological Remediation for Industrial Agglomeration Area, College of Environment and Energy, South China University of Technology, Guangzhou 510006 (China); Song, Wenzhe, E-mail: songwenzhe007@126.com [Ministry of Education Key Laboratory of Pollution Control and Ecological Remediation for Industrial Agglomeration Area, College of Environment and Energy, South China University of Technology, Guangzhou 510006 (China); Hu, Yongyou, E-mail: ppyyhu@scut.edu.cn [State Key Laboratory of Pulp and Paper Engineering, College of Light Industry and Food Science, South China University of Technology, Guangzhou 510640 (China); Ministry of Education Key Laboratory of Pollution Control and Ecological Remediation for Industrial Agglomeration Area, College of Environment and Energy, South China University of Technology, Guangzhou 510006 (China)

2014-09-15

Graphical abstract: In this work, an aerobic column reactor was placed before the USB to maintain micro-oxygen condition in the reactor and the micro-aerobic pentachlorophenol (PCP) degrading granular sludge under oxygen-limited conditions (0.1–0.2 mg L{sup −1}) was successfully obtained. PCP degradation by the micro-aerobic system was studied and the variance of microbial community was also discussed by using PCR-DGGE analysis. - Highlights: • Micro-aerobic granular sludge was cultivated in column-type combined reactors. • PCP biodegradation, VFA accumulation and biogas production were studied. • The function of Methanogenic archaeon in the system was investigated. • Fluctuation and diversity of microbial community were discussed by DGGE analysis. • The dominated microorganisms were identified by 16S rDNA sequences. - Abstract: Column-type combined reactors were designed to cultivate micro-aerobic pentachlorophenol (PCP) degrading granular sludge under oxygen-limited conditions (0.1–0.2 mg L{sup −1}) over 39-day experimental period. Micro-aerobic granular had both anaerobic activity (SMA: 2.34 mMCH{sub 4}/h g VSS) and aerobic activity (SOUR: 2.21 mMO{sub 2}/h g VSS). Metabolite analysis results revealed that PCP was sequentially dechlorinated to TCP, DCP, and eventually to MCP. Methanogens were not directly involved in the dechlorination of PCP, but might played a vital role in stabilizing the overall structure of the granule sludge. For Eubacteria, the Shannon Index (2.09 in inoculated granular sludge) increased both in micro-aerobic granular sludge (2.61) and PCP-degradation granular sludge (2.55). However, for Archaea, it decreased from 2.53 to 1.85 and 1.84, respectively. Although the Shannon Index demonstrated slight difference between micro-aerobic granular sludge and PCP-degradation granular sludge, the Principal Component Analysis (PCA) indicated obvious variance of the microbial composition, revealing significant effect of micro

Enhanced selection of micro-aerobic pentachlorophenol degrading granular sludge

International Nuclear Information System (INIS)

Lv, Yuancai; Chen, Yuancai; Song, Wenzhe; Hu, Yongyou

2014-01-01

Graphical abstract: In this work, an aerobic column reactor was placed before the USB to maintain micro-oxygen condition in the reactor and the micro-aerobic pentachlorophenol (PCP) degrading granular sludge under oxygen-limited conditions (0.1–0.2 mg L −1 ) was successfully obtained. PCP degradation by the micro-aerobic system was studied and the variance of microbial community was also discussed by using PCR-DGGE analysis. - Highlights: • Micro-aerobic granular sludge was cultivated in column-type combined reactors. • PCP biodegradation, VFA accumulation and biogas production were studied. • The function of Methanogenic archaeon in the system was investigated. • Fluctuation and diversity of microbial community were discussed by DGGE analysis. • The dominated microorganisms were identified by 16S rDNA sequences. - Abstract: Column-type combined reactors were designed to cultivate micro-aerobic pentachlorophenol (PCP) degrading granular sludge under oxygen-limited conditions (0.1–0.2 mg L −1 ) over 39-day experimental period. Micro-aerobic granular had both anaerobic activity (SMA: 2.34 mMCH 4 /h g VSS) and aerobic activity (SOUR: 2.21 mMO 2 /h g VSS). Metabolite analysis results revealed that PCP was sequentially dechlorinated to TCP, DCP, and eventually to MCP. Methanogens were not directly involved in the dechlorination of PCP, but might played a vital role in stabilizing the overall structure of the granule sludge. For Eubacteria, the Shannon Index (2.09 in inoculated granular sludge) increased both in micro-aerobic granular sludge (2.61) and PCP-degradation granular sludge (2.55). However, for Archaea, it decreased from 2.53 to 1.85 and 1.84, respectively. Although the Shannon Index demonstrated slight difference between micro-aerobic granular sludge and PCP-degradation granular sludge, the Principal Component Analysis (PCA) indicated obvious variance of the microbial composition, revealing significant effect of micro-aerobic condition and

Sustainable wood use, decarbonisation of energetic metabolism and forest development

DEFF Research Database (Denmark)

Czeskleba-Dupont, Rolf

2009-01-01

Air pollution from wood stoves with PAH, primary particles and chlorinated dioxins (reported according to national estimates of  Danish NERI) is presented as an insoluble problem because of dioxin de-novo-synthesis in chimneys, as it is known from municipal waste incinerators. A trade-off of this......Air pollution from wood stoves with PAH, primary particles and chlorinated dioxins (reported according to national estimates of  Danish NERI) is presented as an insoluble problem because of dioxin de-novo-synthesis in chimneys, as it is known from municipal waste incinerators. A trade......-off of this local pollution against alleged positive impacts of wood (as all biomass) combustion on global climate change because of 'zero carbon dioxide emissions' is rejected, although this resetting to zero is part of the Danish Law on CO2-quota of 2004. These emissions are, on the contrary, aggravated pr. unit...... of energy, when substituting for fossil fuels, whereas compensatory binding of carbon dioxide by tree growth over many decades is referred to an insecure future under global warming. Harvested wood products should rather not be used in atmospheric burners, but in product form. Otherwise an accelerated...

EFFECT OF EXTRACTIVES AND CARBONIZATION TEMPERATURE ON ENERGY CHARACTERISTICS OF WOOD WASTE IN AMAZON RAINFOREST

Directory of Open Access Journals (Sweden)

Jordão Cabral Moulin

2017-06-01

Full Text Available The objective of this study was to evaluate the effect of extractives soluble in hot water, besides final carbonization temperatures, on the gravimetric yield and properties of charcoal for waste of three native forest species from the Amazon region. Waste cuttings of Ipé, Grapia and Maçaranduba species, from the machine processing for joinery of a company in the State of Pará, were used. Carbonization was carried out in an adapted electric furnace with a heating rate of 1.67°C min-1 and final temperatures of 500, 600 and 700°C. The waste was carbonized fresh after extraction in hot water to remove extractives. Gravimetric yields were analyzed, as well as chemical features and high heating value. In the evaluation of the experiment, arranged in a factorial scheme with three factors (species x temperature x material with and without extraction, and Principal Component Analysis used too. The presence of extractives (soluble in hot water from wood waste had little influence on the gravimetric yield and immediate chemical composition of charcoal; however, it showed a greater high heating value and lower contents of hydrogen and nitrogen. The increase in the final carbonization temperature reduced the gravimetric yield in charcoal, the content of volatile materials and hydrogen, with a higher content of fixed carbon, carbon and high heating value. The treatments with the best energy characteristics were obtained from Ipé and Maçaranduba charcoals with extractives produced at 600°C, in addition to Ipê and Maçaranduba charcoals with and without extractives obtained at 700°C.

Selion offers a unique system for treating liquid nuclear waste

Energy Technology Data Exchange (ETDEWEB)

Tusa, E.; Kurki, H. [ed.

1998-07-01

Studies on the treatment of liquid nuclear waste have been conducted actively in the IVO Group since the early 1980s. And the work has borne fruit: the CsTreat and SrTreat ion exchange products, developed by the IVO Group, were launched three years ago. The ion exchangers have already been in full use at a number of sites throughout the world. In addition, they are currently being tested at many nuclear research institutes and power plants in the USA, Japan and Europe

Chemical characteristics and methane potentials of source-separated and pre-treated organic municipal solid waste

DEFF Research Database (Denmark)

Hansen, Trine Lund; Svärd, Å; Angelidaki, Irini

2003-01-01

A research project has investigated the biogas potential of pre-screened source-separated organic waste. Wastes from five Danish cities have been pre-treated by three methods: screw press; disc screen; and shredder and magnet. This paper outlines the sampling procedure used, the chemical...... composition of the wastes and the estimated methane potentials....

Wood quality changes caused by mineral fertilization

Directory of Open Access Journals (Sweden)

Carlos Roberto Sette Jr

2014-06-01

Full Text Available The diverse and important use of wood from fast growth eucalyptus plantations requires the analysis of the effect of mineral fertilizers on wood quality. The objective of this study was to evaluate the anatomical characteristics and wood density from Eucalyptus grandis trees (3 m x 2 m spacing fertilized with potassium and sodium (at planting, 6 th and 12th month. Fifteen (15 6 years old eucalyptus trees were selected (5 trees/treatment, cut and wood samples at DBH (1,3 m were taken for anatomical characteristics (fiber and vessels and wood density analysis. Results showed that eucalyptus trees treated with mineral fertilizers did not show significant alteration in average wood density, with radial profile model common to all three treatments, characterized by a values increase in the region next to the pith, toward to bark. Mineral fertilization influenced wood anatomical characteristics: treatment with sodium was characterized by thinner walls and lumen larger diameter; in treatment with potassium, larger vessels were detected.

USARCENT AOR Contingency Base Waste Stream Analysis: An Analysis of Solid Waste Streams at Five Bases in the U. S. Army Central (USARCENT) Area of Responsibility

Science.gov (United States)

2013-03-31

and Plastics Waste in As Bench Scale Combustor. University of Technology, Malaysia . http://eprints.utm.my/2854/1/75186.pdf. ASTM – ASTM...prevalent types of solid waste are food (19.1% by average sample weight), wood (18.9%), and plastics (16.0%) based on analysis of bases in...within the interval shown. Food and wood wastes are the largest components of the average waste stream (both at ~19% by weight), followed by plastic

Long-term persistence of polychlorinated dibenzo-p-dioxins and dibenzofurans in air, soil and sediment around an abandoned pentachlorophenol factory in China

International Nuclear Information System (INIS)

Li Cheng; Zheng, Minghui; Zhang Bing; Gao Lirong; Liu Lidan; Zhou Xin; Ma Xiaodong; Xiao Ke

2012-01-01

Air, soils and sediments surrounding an abandoned pentachlorophenol (PCP) factory were sampled to determine the levels of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), unintentionally formed during PCP production. The mean concentration of PCDD/Fs in ambient air was one order of magnitude higher than that of the reference site. A trend of decreasing concentrations with increasing distance from the factory was observed, suggesting this site has a significant influence on the regional ambient air. As for soil samples collected within 3 km from the factory and sediment samples from the adjacent rivers, high levels of contamination were found with WHO-TEQ concentrations of 193 ± 211 pg/g and 667 ± 978 pg/g, respectively. The PCDD/F homologue profiles of all samples were consistent with those found in the technical product of PCP, with OCDD as the dominant congener. These results indicate PCDD/Fs in the historical contaminated site pose a long-term impact on surrounding environment. - Highlights: ► PCDD/Fs were investigated in various environmental compartments surrounding an abandoned pentachlorophenol (PCP) factory. ► High levels of PCDD/F contamination were found in ambient air, soils and the sediments around this factory. ► PCDD/F homologue profiles were consistent with PCDD/Fs in technical product of PCP. ► PCDD/Fs in this historical contaminated site pose a long-term impact on surrounding environment. - PCDD/Fs around an abandoned pentachlorophenol factory pose a long-term impact on surrounding environment.

Modification of the original color of the Eucalyptus grandis wood by heat treatments

Directory of Open Access Journals (Sweden)

Rosilei Aparecida Garcia

2014-09-01

Full Text Available The objective of this study was to determine the modification of original color of Eucalyptus grandis Hill ex. Maiden wood after heat-treatment. Wood samples were heat-treated under different temperatures (180, 200, 215 and 230ºC and time conditions (15 minutes, 2 and 4 hours. Color analysis were performed on the CIE L*a*b* system by using a Color Eye XTH-X-Rite 200d spectrophotometer. All heat treatments promoted an alteration of the original color of wood. Heat-treated woods presented lower L* (lightness values than untreated wood (control, characterizing the wood darkness, mainly for more severe conditions of temperature and time. Chromatic coordinates (a* and b* showed different behaviors depending on the temperature-time combination. The modification of the original color of the wood allowed the creation of new color patterns, which can add greater value to the studied wood.

Influence of temperature, mixing and time of residue on the degradation of organic trace materials during thermal treatment of waste wood; Einfluss von Temperatur, Durchmischung und Verweilzeit auf den Abbau organischer Spurenstoffe bei der thermischen Behandlung von Abfallholz

Energy Technology Data Exchange (ETDEWEB)

Beckmann, M [Clausthaler Umwelttechnik-Institut GmbH (CUTEC), Clausthal-Zellerfeld (Germany); Griebel, H [Fels-Werke GmbH, Goslar (Germany); Scholz, R [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. fuer Energieverfahrenstechnik und Brennstofftechnik

1998-09-01

Waste wood, e.g. window frames or sleepers treated with coal tar pitch, are usually incinerated after crushing and removal of foreign materials (glass, metal etc.). Organic trace elements, e.g. PAH, PCB, chlorobenzenes, PCDD and PCDF must be removed after combustion. (orig./SR) [Deutsch] Abfallhoelzer, wie z.B. Fensterrahmen oder mit Steinkohlenteerpech behandelte Eisenbahnschwellen, werden nach Zerkleinerung und Abtrennung von Wert- und Stoerstoffen (Glas, Metalle usw.) haeufig in Rostsystemen thermisch behandelt. Bei der Diskussion der Prozessbedingungen liegt ein besonderer Schwerpunkt in der Fragestellung nach geeigneten Abbaubedingungen fuer organische Spurenstoffe wie polyaromatische Kohlenwasserstoffe (PAK), polychlorierte Biphenyle (PCB), Chlorbenzole, polychlorierte Dibenzodioxine (PCDD) und polychlorierte Dibenzofurane (PCDF) im Nachverbrennungsprozess. (orig./SR)

Study of shrimp shell derivatives for treating of low-level radioactive liquid wastes

Energy Technology Data Exchange (ETDEWEB)

Hayeripour, S. [Tonkabon Islamic Azad Univ., Tonkabon (Iran, Islamic Republic of). College of the Environment; Malmasi, S. [North Tehran Islamic Azad Univ., Tehran (Iran, Islamic Republic of). College of the Environment

2006-07-01

Chitin derivatives can be used to treat liquid wastes that include heavy metals of radionuclides. In this study, 4 types of chitin derivatives from shrimp shell waste were investigated for their potential in decontaminating and treating low-level radioactive liquid waste (LLW). The adsorption of caesium (Cs); cobalt (Co); and manganese (Mn) isotopes on chitin derivatives were investigated using a batch and column system with variations in diameter, pH, and length of treatment. Chitin derivatives included shrimp shells; de-mineralized shrimp shells; chitin extracted from shrimp shells; and chitosan extracted from shrimp shell waste. Three types of simulated solutions were prepared to study and compare adsorption performance: (1) a mono cationic solution consisting of stable isotopes; (2) a solution containing 3 stable cations; and (3) a simulated radioactive waste containing Cs-137, Co-60, and Mn-54. Results of the experiments showed that all 4 chitin derivatives were capable of adsorbing the isotopes. Despite its low pH, chitosan showed the highest adsorption efficiency. It was concluded that shrimps shells provided unreliable results under different operating conditions. The demineralized shells were suitable for removing Co from solutions. Row shells were not recommended as a suitable adsorbent for radionuclides removal. 14 refs., 2 tabs., 6 figs.

CHARACTERIZATION OF EMISSIONS OF THERMALLY MODIFIED WOOD AND THEIR REDUCTION BY CHEMICAL TREATMENT

Directory of Open Access Journals (Sweden)

Jana Peters

2008-05-01

Full Text Available Thermal treatment is a suitable method for improving the quality of wood types like spruce, beech or poplar, and thus to open up new fields of application that used to be limited to tropical woods or woods treated with timber preservatives. These thermally treated woods are characterized by a typical odor caused by degradation products of miscellaneous wood components. The characterization and removal of those odorous substances were investigated using chromatographic and spectroscopic methods. Headspace gas chromatography (GC in combination with solid-phase microextraction (SPME was used for a qualitative analysis of volatile wood emissions, and the detectable volatiles were compared before and after solvent extraction. Wood solvent extractives were investigated by means of gas chromatography/mass spectrometry and then evaluated in terms of changes in composition caused by the thermal treatment process.

Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

Directory of Open Access Journals (Sweden)

Gbemileke A. Ogunranti

2016-09-01

Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic