Dew point of flue gas in the combustion of brown coal briquettes

Energy Technology Data Exchange (ETDEWEB)

Schinkel, W

1977-08-01

Economical operation of small steam generators can follow two courses, viz. to channel the emitted gases through the plant and reduce waste gas loss. Two possibilities exist to achieve this: firstly a steam generating process with only slight excess air; secondly a reduction of the emitted gas temperature. The lowest waste gas temperature found in sulphur-containing combustion materials is measured by finding the acid dew-point of the waste gas. The following results in the case of brown coal briquettes were found. Measurements of the dew point of flue gas in two steam generators, both of the double flue type, one having a capacity of 12.5 t/h, the other 25 t/h, one using brown coal briquettes with 1% sulphur content, the other with 3%, resulted in the fact that the dew point can be measured. It was shown that a low air ratio leads to a lowering of the dew point. However this process is unfortunately economically unviable in chain grate generators as the waste gas becomes so thin under a high air ratio that the dew point can only be minimally reduced. Further the acid dew point is only slightly influenced by partial operation of the generator and the infusion of briquette residue.

Density equation of bio-coal briquettes and quantity of maize cob in Phitsanulok, Thailand

Energy Technology Data Exchange (ETDEWEB)

Patomsok Wilaipon [Naresuan University, Phitsanulok (Thailand). Department of Mechanical Engineering

2008-07-01

One of the most important crops in Phitsanulok, a province in Northern Thailand, is maize. BaseD on the calculation, the quantity of maize cob produced in this region was approximately 220 kton year{sup -1}. The net heating value of maize cob was found to be 14.2 MJ kg{sup -1}. Therefore, the total energy over 874 TJ year-1 can be obtained from this agricultural waste. In the experiments, maize cob was utilized as the major ingredient for producing biomass-coal briquettes. The maize cob was treated with sodium hydroxide solution before mixing with coal fine. The ratios of coal:maize were 1:2 and 1:3, respectively. The range of briquetting pressures was from 4-8 MPa. The result showed that the density was strongly affected by both parameters. Finally, the relationship between biomass ratio, briquetting pressures and briquette density was developed and validated by using regression technique. 13 refs., 2 figs.

The synergistic effect in coal/biomass blend briquettes combustion on elements behavior in bottom ash using ICP-OES

Energy Technology Data Exchange (ETDEWEB)

Lazaroiu, G.; Frentiu, T.; Maescu, L.; Mihaltan, A.; Ponta, M.; Frentiu, M.; Cordos, E. [Universitatea Politehnica din Bucuresti, Bucharest (Romania)

2009-05-15

This paper focuses on the study of the synergistic effect in coal/biomass blend briquettes combustion on behavior of Al, As, Ba, Cd, Co. Cr, Cu, Fe, Ga, K, Mn, Mo, Ni, P, Pb, Si, V, W, Zn, Zr and characterization of raw materials and bottom ashes. The manufacturing of coal/biomass briquettes although not commonly used is an attractive approach, as briquettes combustion is more technologically advantageous than the fluidized bed combustion. In the same time this technology is a way to render valuable materials of low calorific power and results in diminishing polluting emission. Raw materials and briquettes from different blends of pitcoal/sawdust were subjected to combustion in a 55 kW-boiler. The total content of elements after digestion in the HNO{sub 3} - HF mixture and the content in water leachate at a solid/liquid ratio of 1:2 were determined both in raw materials and bottom ash by ICP-OES. The total content of elements was higher in pitcoal than in sawdust. The synergistic effect depends both on coal/biomass ratio in blend and element nature. The water leachable fraction of elements from ash decreased along with the increase of sawdust weight excepting macronutrients (K, P) and Si.

Demonstration of the Viability and Evaluation of Production Costs for Biomass-Infused Coal Briquettes

Energy Technology Data Exchange (ETDEWEB)

Kamshad, Kourosh [Coaltek Incorporated, Tucker, GA (United States)

2014-04-01

This project was split into four main areas, first to identify the best combination of coal and biomass, second, create and test lab quantity of preferred combinations, Third, create a sizeable quantity for larger scale handling and consuming analysis and fourth, to provide analysis for a commercial scale production capacity. Samples of coal and biomass were collected. Five coals, representing the three major coal ranks, were collected including one bituminous, two sub-bituminous, and two lignite samples. In addition, three square bales (~50 lbs/bale) each of corn Stover and switch grass were collected with one bale of each sample processed through a hammer mill to approximately -5 mesh. A third sample of sawdust was collected once experimentation began at the University of Kentucky. Multiple combinations of coal and biomass; coal, biomass, with biomass binder, were tested until a formulation was identified that could meet the requirement criteria. Based on the results of the binderless briquetting evaluations, the CS/Sub-bit combinations was selected for extended evaluation at a 10% biomass addition rate while the WS/Bitum combination was selected for extended evaluation at a 30% biomass-addition rate. With the final results of the selection process complete, the CoalTek continuous production pilot plant in Tucker GA was outfitted with the specialized blending equipment and two 1/4 ton production runs of biomass and binder subbituminous coal briquettes were completed. These briquettes were later used for a calorific test burn at the University of North Dakota. The first formulation included subbituminous coal, corn stover and a corn starch binder the second formulation included subbituminous coal, wheat stover and corn starch binder.

Utilisation of the binders prepared from coal tar pitch and phenolic resins for the production metallurgical quality briquettes from coke breeze and the study of their high temperature carbonization behaviour

Energy Technology Data Exchange (ETDEWEB)

Benk, Ayse [University of Erciyes, Faculty of Art and Science, Department of Chemistry, 38039, Kayseri (Turkey)

2010-09-15

To reduce the cost of the formed coke briquettes which can be used as a substitute fuel to the metallurgical coke for the blast furnace from the coke breeze alternative binders and their blends were used. The high temperature behavior was investigated. The binders tested were: the nitrogen blown, air blown coal tar pitch and the blend of air blown coal tar pitch with the phenolic resins blends. The phenolic resin blends were prepared by mixing equal amount of resole and novalac. From the results, nitrogen blowing resulted in the weakest briquettes. The air blowing procedure should be preferred in place of nitrogen blowing for this purpose. When the air blown coal tar pitch was used alone as a binder, the briquettes must be cured at 200 C for 2 h, then carbonized at a temperature above 670 C. Since it requires higher temperature at carbonization stage, using air blown coal tar pitch alone as a binder was not economical. Therefore, the briquettes were prepared from the blended binder, containing air blown coal tar pitch and phenolic resins blend. The optimum amount of air blown coal tar pitch was found to be 50% w/w in the blended binder. Curing the briquettes at 200 C for 2 h was found to be sufficient for producing strong briquettes with a tensile strength of 50.45 MN/m{sup 2}. When these cured briquettes were carbonized at temperatures 470 C, 670 C and 950 C, their strength were increasing continuously, reaching to 71.85 MN/m{sup 2} at the carbonization temperature of 950 C. These briquettes can be used as a substitute for the metallurgical coke after curing; the process might not require un-economical high temperature carbonization stage. (author)

Preparation of briquettes on the basis of desintegrated phyto-materials and the admixture of fine-grained coal and coke

Directory of Open Access Journals (Sweden)

Jakabský Štefan

2002-03-01

Full Text Available The contribution deals with the preparation of small-diameter briquettes on the basis of desintegrated phyto-materials and the admixture of coal and coke. The phyto-materials are classified as a dry biomass that can be, on the one hand, the wastes from wood-working industry,(sawdust, chips, bark, etc. or dried mass from the plant production and, on the other hand, the mass of quick-growing plants cultivated on special plantations. In present time this renewable energy resource attracts attention by its heating value ranging from 10 to 16 MJ.kg-1 (EkoWATT, 2001, a low ash content of 0.5 – 6.5 % and by a low sulphur content in a water free sample of 0.05 –0.12 %.As a phyto-material the spruce sawdusts having a grain size of –2 mm were used. The admixture of brown coal, hard coal and coke with a grain size of 0.040 mm was added to the sawdust and in such way prepared mixtures were subjected to briquetting with the aim to obtain small-diameter briquettes. The influence of admixtures amount on the density, and the suitable briquetting press have been studied. A saleability of briquettes on the basis of phyto-materials is conditioned by their density that must be higher than 1,000 kg.m-3. Thus, an adding of denser material with a relatively high calorific value would enable to attain the required density as well as to retain and/or to improve the main utility properties, i.e. calorific value and ash content.The adding evinces itself in an enhancement of briquetting press, but also density of obtained briquettes is often much higher that required by the market. It was showed that in the case of clear spruce sawdust the density of 1,059 kg.m-3 under the briquetting press of 250 MPa can be attained. According to other results, an admixture of brown coal is not very favourable because briquetting press exceeds the value of 300 MPa. As to hard coal adding, the presses under 250 MPa were achieved at the content of 25 – 30 %. The density of these

Report on investigations in fiscal 2000 on the projects to support introduction of environment friendly coal utilization system. Green helmet project for briquette production plant - Mae Moh coal mine, Thailand; 2000 nendo kankyo chowagata sekitan riyo system donyu shien jigyo chosa hokokusho. Briquette seizo setsubi ni kakawaru green helmet jigyo (Thai koku Mae Moh tanko)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

This Green Helmet Project is intended to suppress generation of environment polluting substances in association with coal utilization in Thailand by demonstrating and improving the proliferation infrastructure for the clean coal technology to be used widely in Thailand. The project is also intended to serve for stabilized assurance of energies for Japan. The demonstration project related to briquette manufacturing facilities executed as one of the 'Projects to support introduction of environment friendly coal utilization system' is intended to manufacture at low cost a briquette which is low in odor, free of smoke, and suppressed largely of sulfur oxide generation. The briquette is made by adding clayish minerals, sulfur, a fixing agent and a binder into brown coal being a low grade coal. The project implements proliferation of the technology to reduce environmental load associated with coal utilization in developing countries according to the situation and needs of the counterpart countries. The present project has performed the site surveys and guidance of operation and maintenance techniques as follow-up works of the demonstration project having been completed by cooperation between Japan and Thailand. It is considered that what had been intended in the beginning has been achieved sufficiently. (NEDO)

The Utilization of Bottom Ash Coal for Briquette Products by Adding Teak Leaves Charcoal, Coconut Shell Charcoal, and Rice Husk Charcoal

Directory of Open Access Journals (Sweden)

Syafrudin Syafrudin

2015-01-01

Full Text Available The limitations of the availability of energy sources especially fuel oil has become a serious threat for the society. The use of coal for energy source as the replacement of fuel oil, in one hand, is very profitable, but on the other hand, will cause problem which is the coal ash residue. This coal ash is a by-product of coal combustion. This coal ash contains bottom ash. Through this observation, the bottom ash can be processed to be charcoal if added by teak leaves, coconut shell, and rice husk. Also, this observation needs to add binder materials for further processing in order to form briquette. It can be used as alternative fuel, the utilization of bottom ash and biomass will give positive impact to the environment. This observation was conducted by using compositions such as bottom ash, teak leaves, coconut shell, and rice husk. The treatment was using comparison 100%:0% ; 80%:20% ; 60%:40% ; 50%:50% ; 40%:60% ; 20%:80% ; 0%:100%. The result that the best briquette was on the composition of 20% bottom ash : 80% coconut shell. The characteristic values from that composition were moisture content of 3.45%, ash content of 17,32%, calorific value of 7.945,72 Cal/gr, compressive strength of 2,18 kg/cm2, level of CO of 105 mg/m3, and heavy metals Cu of 29,83 µg/g and  Zn 32,99 µg/g. The characteristic value from each briquette composition treatment showed that the increasing usage proportion of biomass as added material for briquette was able to increase its moisture content and calorific value. Besides, it is also able to decrease its ash content and compressive strength

Study on Reduction Kinetics of Briquettes of Hematite Fines with Boiler Grade Coal and Coke Dust in Two Different Forms: Intermixing and Multilayered

Science.gov (United States)

Roy, Gopal Ghosh; Sarkar, Bitan Kumar; Chaudhuri, Mahua Ghosh; Mitra, Manoj Kumar; Dey, Rajib

2017-10-01

An attempt has been made to utilise hematite ore fines in the form of briquettes with two different form of mixing i.e. intermixing and multilayered by means of carbothermal reduction along with boiler grade coal and coke dust. The influence of reduction temperature (1323, 1373 and 1423 K) and reduction time (10, 20, 30, 45 and 60 min) has been investigated in detail and the reduced briquettes are characterised by XRD, SEM analyses. The reducibility of intermixing briquettes is found to be higher for multilayered briquettes. In addition, isothermal kinetic study has also been carried out for both intermixing and multilayered briquettes. The activation energy for intermixing briquettes are evaluated to be 125.88 kJ/mol for the initial stage of reaction (CG3 controlled mechanism) and 113.11 kJ/mol for the later part of reaction (D3 controlled mechanism), respectively. In case of multilayered briquettes, the corresponding activation energy is found to be 235.59 kJ/mol for reaction (CG3 controlled mechanism). These results corroborate the observed better reducibility of the intermixing briquettes over multilayered briquettes.

Boiler briquette coal versus raw coal: Part I--Stack gas emissions.

Science.gov (United States)

Ge, S; Bai, Z; Liu, W; Zhu, T; Wang, T; Qing, S; Zhang, J

2001-04-01

Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM10 and PM2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM10, 0.38 for PM2.5, 20.7 for SO2, and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM10, 0.30 for PM2.5, 7.5 for SO2, and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM10, 0.87 for PM2.5, 46.7 for SO2, and 15 for CO, while those of the BB-coal were 2.51 for PM10, 0.79 for PM2.5, 19.9 for SO2, and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/steam conversion factors, were 0.23 for PM10, 0.12 for PM2.5, 6.4 for SO2, and 2.0 for CO, while those of the BB-coal were 0.30 for PM10, 0.094 for PM2.5, 2.4 for SO2, and 1.7 for CO. PM10 and PM2.5 elemental compositions are also presented for both types of coal tested in the study.

Boiler Briquette Coal versus Raw Coal: Part I-Stack Gas Emissions.

Science.gov (United States)

Ge, Su; Bai, Zhipeng; Liu, Weili; Zhu, Tan; Wang, Tongjian; Qing, Sheng; Zhang, Junfeng

2001-04-01

Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM 10 and PM 2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM 10 , 0.38 for PM 25 , 20.7 for SO 2 , and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM 10 , 0.30 for PM 2 5 , 7.5 for SO 2 , and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM 10 , 0.87 for PM 25 , 46.7 for SO 2 , and 15 for CO, while those of the BB-coal were 2.51 for PM 10 , 0.79 for PM 2.5 , 19.9 for SO 2 , and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/ steam conversion factors, were 0.23 for PM 10 , 0.12 for PM 2.5 , 6.4 for SO 2 , and 2.0 for CO, while those of the BB-coal were 0.30 for PM 10 , 0.094 for PM 2.5 , 2.4 for SO 2 , and 1.7 for CO. PM 10 and PM 2.5 elemental compositions are also presented for both types of coal tested in the study.

Fluorine-fixing efficiency on calcium-based briquette: pilot experiment, demonstration and promotion.

Science.gov (United States)

Yang, Jiao-lan; Chen, Dong-qing; Li, Shu-min; Yue, Yin-ling; Jin, Xin; Zhao, Bing-cheng; Ying, Bo

2010-02-05

The fluorosis derived from coal burning is a very serious problem in China. By using fluorine-fixing technology during coal burning we are able to reduce the release of fluorides in coal at the source in order to reduce pollution to the surrounding environment by coal burning pollutants as well as decrease the intake and accumulating amounts of fluorine in the human body. The aim of this study was to conduct a pilot experiment on calcium-based fluorine-fixing material efficiency during coal burning to demonstrate and promote the technology based on laboratory research. A proper amount of calcium-based fluorine sorbent was added into high-fluorine coal to form briquettes so that the fluorine in high-fluorine coal can be fixed in coal slag and its release into atmosphere reduced. We determined figures on various components in briquettes and fluorine in coal slag as well as the concentrations of indoor air pollutants, including fluoride, sulfur dioxide and respirable particulate matter (RPM), and evaluated the fluorine-fixing efficiency of calcium-based fluorine sorbents and the levels of indoor air pollutants. Pilot experiments on fluorine-fixing efficiency during coal burning as well as its demonstration and promotion were carried out separately in Guiding and Longli Counties of Guizhou Province, two areas with coal burning fluorosis problems. If the calcium-based fluorine sorbent mixed coal was made into honeycomb briquettes the average fluorine-fixing ratio in the pilot experiment was 71.8%. If the burning calcium-based fluorine-fixing bitumite was made into a coalball, the average of fluorine-fixing ratio was 77.3%. The concentration of fluoride, sulfur dioxide and PM10 of indoor air were decreased significantly. There was a 10% increase in the cost of briquettes due to the addition of calcium-based fluorine sorbent. The preparation process of calcium-based fluorine-fixing briquette is simple yet highly flammable and it is applicable to regions with abundant

Coal statistics 1977

Energy Technology Data Exchange (ETDEWEB)

Statistical Office of the European Communities

1978-01-01

Presents tables of data relating to the coal market in the European Community in 1977. The tables cover hard coal production, supply and trade; briquettes; cokes; lignite, brown coal briquettes and peat; and mines and coke ovens.

PENGEMBANGAN TUNGKU BRIKET BATUBARA SKALA RUMAH TANGGA Improvement of a Coal Briquette Stove for Household Scale

Directory of Open Access Journals (Sweden)

Tamrin Tamrin

2012-05-01

Full Text Available Improving of a coal briquette stove is required in the context of energy diversification for strengthening national energy security. The policy of kerosene conversion to LPG is a short term policy and needs other source of energy alternative.  In idealized sense, all potentials should be used for household cooking, not always depending on a particular energy source. Purpose of this research was to improve a household coal briquette stove to increase stove efficiency and ease in ceasing the ember. Design criteria of the coal briquette stove were based on heat transfer from the burning coal to the heated object, ease in ceasing the ember, and facilitating the exhausting smoke from the kitchen room. Performance test to the designed stove was conducted on analyses of temperature at the bottom of a pan versus time during the firing, heat efficiency, and the time of ceasing ember. The results showed that the cooking temperature (>180 oC was reached after 35-65 minutes. The cooking temperature lasted for 4 hours, heat efficiency of 25.5 % was about optimum, and the time of ember ceasing was 19-33 minutes. ABSTRAK Pengembangan tungku briket batubara sangat diperlukan dalam diversifikasi pemakaian energi bahan bakar agar ketahanan energi nasional  menjadi kuat.  Kebijakan pengalihan bahan bakar minyak tanah ke elpiji merupakan ke- bijakan jangka pendek dan perlu energi alternatif lainnya  Idealnya  semua potensi yang ada dapat digunakan untuk memasak, tidak harus bergantung pada energi tertentu.  Tujuan penelitian ini adalah untuk mengembangkan tungku briket batubara skala rumah tangga untuk meningkatkan efiseinsi dan memudahkan pematian bara api. Tungku briket batubara dibuat didasarkan pada sistem pindah panas dari bara briket ke objek yang dipanaskan, memudahkan pe- matian bara api briket batubara dan menyalurkan asap dari ruang pembakaran keluar dari ruang dapur. Pengujian dilakukan untuk mengetahui perubahan suhu dasar panci selama pembakaran

Briquetting mechanism and waterproof performance of bio-briquette

Energy Technology Data Exchange (ETDEWEB)

Huang, G.; Chen, L.; Cao, J. [Henen Polytechnic University, Jiaozuo (China)

2008-07-15

Maize stalk and bio-briquette binder made from it were studied comparatively by FTIR and the microstructure of bio-briquette was observed and analyzed by microscopy. It was found that a large amount of unreacted biomass fibers exist in the binder. These form a multi-level network structure inside the bio-briquette and could make fine coal particles connect together. The multi-level network structure would be still present after the bio-briquettes are immersed in water for 24 hours. On the other hand, stalk materials could be partly degraded after treatment and, with other liquid ingredients in the binder, the degradation products could form a viscous fluid which would work as a bonding ingredient inside the bio-briquette and could improve the waterproofing ability of the binder after solidification. Therefore, the multi-level network structure of the biomaterial and the presence of viscous fluid are very important to the shaping and the improvement of the waterproofing ability of bio-briquettes. 11 refs., 3 figs.

Preliminary study of realizability of Karazhyra open pit coal fines briquetting

International Nuclear Information System (INIS)

Deryavko, I.I.; Perepelkin, I.G.; Chuprunov, K.V.

2001-01-01

Main properties of brown coals in Karazhyra open pit upper and lower packs are determined. Characteristics of these coals briquette-ability are evaluated. A conceptual possibility to obtain high-quality briquettes from open pit coal fines is shown. (author)

Evaluation of water hyacinth (Eichhornia crassipes) as a potential raw material source for briquette production

International Nuclear Information System (INIS)

Rezania, Shahabaldin; Md Din, Mohd Fadhil; Kamaruddin, Siti Fatimah; Taib, Shazwin Mat; Singh, Lakhveer; Yong, Ee Ling; Dahalan, Farrah Aini

2016-01-01

In the present study we investigated the fuel properties of bio-briquettes made from a combination of water hyacinth and empty fruit bunch fiber (palm oil mill residue). Water hyacinth (WH) was mixed with empty fruit bunch (EFB) fibers in a ratio of 25, 50, 75, 90, and 100% by weight and cassava starch added as binder. The experimental results showed that the addition of WH had a little effect (p < 0.05) on the physical and combustion properties of the briquettes. The proximate analysis showed that the moisture content, ash content and fixed carbon content were increased with the increase in WH amount from 25 to 100%, while the volatile matter content and calorific value decreased. Combustion test showed that the increase in the WH percentage in bio-briquette resulted in the decreased of O_2 and CO level, whereas, that of CO_2 and NO, NO_2 and SO_2 were increased. Therefore, the results conclude that the WH: EFB biomass bio-briquette could be a great potential as an alternative source to conventional coal to minimize the emission of greenhouse gases. - Highlights: • Fuel briquettes of mixtures of water hyacinth and empty fruit bunches were studied. • Various ratios of WH and EFB were analyzed, burned and the flue gas analyzed. • A ratio of WH 25% and EFB 75% was the optimum mixture. • The mixed content briquettes burn well with coal and can displace some coal.

Advanced Systems for Preprocessing and Characterizing Coal-Biomass Mixtures as Next-Generation Fuels and Feedstocks

Energy Technology Data Exchange (ETDEWEB)

Karmis, Michael [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Luttrell, Gerald [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Ripepi, Nino [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Bratton, Robert [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Dohm, Erich [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

2014-09-30

The research activities presented in this report are intended to address the most critical technical challenges pertaining to coal-biomass briquette feedstocks. Several detailed investigations were conducted using a variety of coal and biomass feedstocks on the topics of (1) coal-biomass briquette production and characterization, (2) gasification of coal-biomass mixtures and briquettes, (3) combustion of coal-biomass mixtures and briquettes, and (4) conceptual engineering design and economic feasibility of briquette production. The briquette production studies indicate that strong and durable co-firing feedstocks can be produced by co-briquetting coal and biomass resources commonly available in the United States. It is demonstrated that binderless coal-biomass briquettes produced at optimized conditions exhibit very high strength and durability, which indicates that such briquettes would remain competent in the presence of forces encountered in handling, storage and transportation. The gasification studies conducted demonstrate that coal-biomass mixtures and briquettes are exceptional gasification feedstocks, particularly with regard to the synergistic effects realized during devolatilization of the blended materials. The mixture combustion studies indicate that coal-biomass mixtures are exceptional combustion feedstocks, while the briquette combustion study indicates that the use of blended briquettes reduces NO_x, CO₂, and CO emissions, and requires the least amount of changes in the operating conditions of an existing coal-fired power plant. Similar results were obtained for the physical durability of the pilot-scale briquettes compared to the bench-scale tests. Finally, the conceptual engineering and feasibility analysis study for a commercial-scale briquetting production facility provides preliminary flowsheet and cost simulations to evaluate the various feedstocks, equipment selection and operating parameters.

Developing Engineered Fuel (Briquettes) Using Fly Ash from the Aquila Coal-Fired Power Plant in Canon City and Locally Available Biomass Waste

Energy Technology Data Exchange (ETDEWEB)

H. Carrasco; H. Sarper

2006-06-30

The objective of this research is to explore the feasibility of producing engineered fuels from a combination of renewable and non renewable energy sources. The components are flyash (containing coal fines) and locally available biomass waste. The constraints were such that no other binder additives were to be added. Listed below are the main accomplishments of the project: (1) Determination of the carbon content of the flyash sample from the Aquila plant. It was found to be around 43%. (2) Experiments were carried out using a model which simulates the press process of a wood pellet machine, i.e. a bench press machine with a close chamber, to find out the ideal ratio of wood and fly ash to be mixed to get the desired briquette. The ideal ratio was found to have 60% wood and 40% flyash. (3) The moisture content required to produce the briquettes was found to be anything below 5.8%. (4) The most suitable pressure required to extract the lignin form the wood and cause the binding of the mixture was determined to be 3000psi. At this pressure, the briquettes withstood an average of 150psi on its lateral side. (5) An energy content analysis was performed and the BTU content was determined to be approximately 8912 BTU/lb. (6) The environmental analysis was carried out and no abnormalities were noted. (7) Industrial visits were made to pellet manufacturing plants to investigate the most suitable manufacturing process for the briquettes. (8) A simulation model of extrusion process was developed to explore the possibility of using a cattle feed plant operating on extrusion process to produce briquettes. (9) Attempt to produce 2 tons of briquettes was not successful. The research team conducted a trial production run at a Feed Mill in La Junta, CO to produce two (2) tons of briquettes using the extrusion process in place. The goal was to, immediately after producing the briquettes; send them through Aquila's current system to test the ability of the briquettes to flow

Fiscal 1998 research report. Improvement project of low-grade coals in Chongqing City, China for CO{sub 2} reduction (Feasibility study on the production business of coal- biomass briquette); 1998 nendo chosa hokokusho. CO{sub 2} sakugen no tame no Chuka Jinmin Kyowakoku Jukei chokkatsushi no teihin'i sekitanshitsu no kaizen project (Bio briquette seizo jigyo no chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study was made on the effect of introduction of production technology of coal-biomass briquette (Japanese coal improvement technology) in Chongqing City on reduction of greenhouse effect gases and acid rain causative substances, and sustainable economic growth. The study result on the feasibility of this project and reduction of greenhouse effect gases was summarized. In this feasibility study, Japan-China joint field survey, and both proximate and ultimate analyses of obtained raw materials were carried out. Based on the experimental result in the pilot briquette plant in Chongqing City, study was made on the necessary of the 1 Mtons/y class pilot plant in the pilot area including Nantong coal mine in Chongqing City, and the location, investment, production cost and distribution means of the plant. Based on the evaluation result on CO{sub 2} reduction effect, economical efficiency, environment effect and social effect, its urgency and effectiveness as international cooperation project by yen credit were also confirmed. It is extremely important to promote localization of the plant in the future. (NEDO)

Fiscal 1998 research report. Improvement project of low-grade coals in Chongqing City, China for CO{sub 2} reduction (Feasibility study on the production business of coal- biomass briquette); 1998 nendo chosa hokokusho. CO{sub 2} sakugen no tame no Chuka Jinmin Kyowakoku Jukei chokkatsushi no teihin'i sekitanshitsu no kaizen project (Bio briquette seizo jigyo no chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study was made on the effect of introduction of production technology of coal-biomass briquette (Japanese coal improvement technology) in Chongqing City on reduction of greenhouse effect gases and acid rain causative substances, and sustainable economic growth. The study result on the feasibility of this project and reduction of greenhouse effect gases was summarized. In this feasibility study, Japan-China joint field survey, and both proximate and ultimate analyses of obtained raw materials were carried out. Based on the experimental result in the pilot briquette plant in Chongqing City, study was made on the necessary of the 1 Mtons/y class pilot plant in the pilot area including Nantong coal mine in Chongqing City, and the location, investment, production cost and distribution means of the plant. Based on the evaluation result on CO{sub 2} reduction effect, economical efficiency, environment effect and social effect, its urgency and effectiveness as international cooperation project by yen credit were also confirmed. It is extremely important to promote localization of the plant in the future. (NEDO)

A comparative study between the coal-biomass briquette and raw coal in SO{sub 2} pollution and adverse effects in rabbits

Energy Technology Data Exchange (ETDEWEB)

Cheng Shuqun; Zhou Yanrong; Wang Yi' nan; Wang Xun; Liu Yuanfu; Iwao Uchiyama; Wang Qiangyue; Kazuhiki Sakamoto [Chongqing University of Medical Sciences. Chongqing (China). School of Public Health

2006-12-15

This study was conducted to evaluate the adverse health effects on rabbits exposed to SO{sub 2} emitted indoors from burning coals, and compare differences between coal-biomass briquette (BB) and raw coal (RC). Thirty-six male rabbits were divided equally into three groups at random, and then exposed to burning RC, BB, and the third without burning coal (Control) for 90 days. Data showed that the average concentration of SO{sub 2} in 24 h in RC was 13.04 mg m{sup -3}, which was 5-fold greater than BB and 31-fold higher than control (0.41 mg m{sup -3}). After 45 days, the numbers of rabbits, with increased frequency of Comet cell was highest in RC. After 90 days, the % positive Comet cell was significant at 10.36% in RC, 5.42% in BB, and 1.73% in Control. There was a nonlinear dose-effect relationship between % positive Comet cell and the concentration of SO{sub 2}. The incidence of interstitial pneumonia was 6/12 in RC and 4/12 in BB showing severe squamous metaplasia with atypical hyperplasia in bronchial epithelia in RC animals. The results of study indicate that use of BB reduced the emission of SO{sub 2}; but the smoke emitted from burning coal still produced DNA damage.

Production and quality testing of fuel briquettes made from ...

Indian Academy of Sciences (India)

Santhosh Ujjinappa

2018-04-13

Apr 13, 2018 ... Thus, this work proved that the blending of PS and TS gives better quality briquettes ... parameters such as compressed density, relaxed density, relaxation ratio ... developed for coal. The test was conducted after two weeks.

Reduction Behaviors of Carbon Composite Iron Oxide Briquette Under Oxidation Atmosphere

Energy Technology Data Exchange (ETDEWEB)

Lee, Ki-Woo; Kim, Kang-Min; Kwon, Jae-Hong; Han, Jeong-Whan [Inha University, Incheon (Korea, Republic of); Son, Sang-Han [POSCO, Pohang (Korea, Republic of)

2017-01-15

The carbon composite iron oxide briquette (CCB) is considered a potential solution to the upcoming use of low grade iron resources in the ironmaking process. CCB is able to reduce raw material cost by enabling the use of low grade powdered iron ores and coal. Additionally, the fast reduction of iron oxides by direct contact with coal can be utilized. In this study, the reduction behaviors of CCB were investigated in the temperature range of 200-1200 ℃ under oxidizing atmosphere. Briquettes were prepared by mixing iron ore and coal in a weight ratio of 8:2. Then reduction experiments were carried out in a mixed gas atmosphere of N{sub 2}, O{sub 2}, and CO{sub 2}. Compressive strength tests and quantitative analysis were performed by taking samples at each target temperature. In addition, the reduction degree depending on the reaction time was evaluated by off-gas analysis during the reduction test. It was found that the compressive strength and the metallization degree of the reduced briquettes increased with increases in the reaction temperature and holding time. However, it tended to decrease when the re-oxidation phenomenon was caused by injected oxygen. The degree of reduction reached a maximum value in 26 minutes. Therefore, the re-oxidation phenomenon becomes dominant after 26 minutes.

Clean fuel-magnesia bonded coal briquetting

Energy Technology Data Exchange (ETDEWEB)

Tosun, Yildirim I. [S. Demirel University Eng., Arch. Faculty Mining Eng. Department, Isparta (Turkey)

2007-10-15

Benefaction from coal fines as solid fuel in Turkey is very much important for economical development. Beneficiation from washed coal fines in the industry using solid fuel at lump size and in the municipal areas as an household solid fuel may be only provided by hot briquetting of the coal fines. The most practical common way of that benefication from coal fines in our country have been hot binding by sulfite liquor-sulfite liquor-melas and lime mixtures. Harmful the flue content of sulfite liquor-melas may only be eliminated by lime, a type of solid additive. However, cold bonded briquettes produced from coal fines are environmentally free. Just ash contents of these briquettes increase at a certain degree and heat content of them decrease at a certain extent. By using magnesia binder showed in this study, Tuncbilek lignite fines have been briquetted by cold and hot briquetting techniques. The qualities of briquettes produced by cold binders were compared with to those produced by other hot binding methods As a result, magnesia binder showed the similar characteristics with those of the briquettes produced by only cold bonded gypsum. Use of magnesite mixture and gypsum just as only cold binder was not suitable for the requirements from the coal briquettes to be used as solid fuels, particularly from household fuels, but just only as cold additive should be used. (author)

Coal pre-feasibility assessment

International Nuclear Information System (INIS)

1994-03-01

It examines the feasibility of using coal from the Delbi-Moya reserve for domestic or institutional cooking, industrial process heating and electricity generation. It indicates as coal can be mined from the Delbi reserve at a cost of EB110/tonne, can be processed for EB400/tonne and transported to Addis Ababa for 150/tonne. The wholesale price of coal briquettes in Addis Ababa would be EB750/tonne. Domestic users can save EB475 per year by switching from charcoal to coal briquettes. And for a 50MW plant annual saving would be of the order of EB30 million per year. 11 tab. 4 figs. 6 appendex

Briquetting of Coke-Brown Coal Mixture

Directory of Open Access Journals (Sweden)

Ïurove Juraj

1998-09-01

Full Text Available The paper presents the results of the research of briquetting a coke-brown coal composite The operation consists of the feeding crushed coal and coke to moulds and pressing into briquettes which have been made in the Laboratories at the Mining Faculty of Technical University of Košice (Slovakia. In this research, all demands will be analyzed including the different aspects of the mechanical quality of briquettes, the proportion of fine pulverulent coal and coke in bricks, the requirements for briquetting the coke-brown coal materials.

Cooling of wood briquettes

Directory of Open Access Journals (Sweden)

Adžić Miroljub M.

2013-01-01

Full Text Available This paper is concerned with the experimental research of surface temperature of wood briquettes during cooling phase along the cooling line. The cooling phase is an important part of the briquette production technology. It should be performed with care, otherwise the quality of briquettes could deteriorate and possible changes of combustion characteristics of briquettes could happen. The briquette surface temperature was measured with an IR camera and a surface temperature probe at 42 sections. It was found that the temperature of briquette surface dropped from 68 to 34°C after 7 minutes spent at the cooling line. The temperature at the center of briquette, during the 6 hour storage, decreased to 38°C.

Coal briquetting at the presence of humates as the binding substance

Directory of Open Access Journals (Sweden)

Zh. Arziev

2013-09-01

Full Text Available The results of coal briquetting at the presence of humates derived from coal at the stage of its chemical preparation by the extraction method are resulted in the paper. The conditions of briquetting and strength characteristics of the received briquettes are optimized. It is demonstrated that briquettes with the durability reaching 3 MPa can be derived from a coal fines using sodium, ammonium and silicate humates as binding substance. Water solutions of ammonium, sodium and silicate humates with concentration from 0,1-2% can be recommended for practical purposes. It is recommended to expose coal briquettes on a basis of ammonium humate to the thermal treatment at temperature 200°C as necessary of long storage (more than a year. The technological scheme of briquetting and the working project of creation of briquette factory with productivity of 40 000 tons of coal per year are developed.

Curing temperature effect on mechanical strength of smokeless fuel briquettes prepared with humates

Energy Technology Data Exchange (ETDEWEB)

M.J. Blesa; J.L. Miranda; M.T. Izquierdo; R. Moliner; A. Arenillas; F. Rubiera [Instituto de Carboquimica (CSIC), Zaragoza (Spain)

2003-04-01

The effect of curing temperature on smokeless fuel briquettes has been studied by Fourier transform infrared spectroscopy (FT-IR), mass spectrometry (MS), and temperature programmed decomposition (TPD). These techniques help to predict the final properties of these briquettes which were prepared with a low-rank coal, sawdust, and olive stone as biomasses and humates as binder. The best mechanical properties are reached with both the mildest thermal curing at 95{sup o}C and the cocarbonized at 600{sup o}C of Maria coal (M2) and sawdust (S) due to the fibrous texture of sawdust. The temperature of curing causes the release of a certain amount of oxygenate structures and the decrease of the mechanical resistance. 15 refs., 7 figs., 3 tabs.

Coal industry statistics for 1977

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

In 1977 Belgian coal production reached 7,068,000 t, a drop of 170,000 t (2.3%) on the previous year. Production from the Campine coalfield had risen by 160,000 t while in the South, where two pits had been shut down during the year, there was a fall in output of 330,000 t. On 31st December 1977 the number of underground personnel totalled 17,681 as against 19,154 at the same time in 1976. Underground output continued to decline in the South while in the Campine there was an increase of 7.6%. Pit-head stocks fell by 400,000 t, to 721,000 t, 658,000 t of this being held in the Campine collieries. As regards Belgian coal disposals, the only increase (+52.0%) was in coal sent to power stations. Import figures stood at 6,592,000 t, a drop of 10.5% over the previous year. Includes figures for apparent coal consumption, a com parison of coal figures for 1976 and 1977 and the mined-coal production. Shows how coal production has evolved in the various coalfields and the number of pits in operation. Production is classified into coal types. Also covers the shutting-down of production capacities; manpower and OMS; coal briquette production; briquette output and disposals; end-of-year pit-head stocks according to coalfields, grades and types of coal. Figures for apparent consumption of coal and coal briquettes; exports and imports 1973-77 and countries of origin. Gives delivery figures for Belgian and imported coal to the domestic market. (In French)

Combustion quality analysis of briquettes from variety of agricultural waste as source of alternative fuels

Science.gov (United States)

Suryaningsih, S.; Nurhilal, O.; Yuliah, Y.; Mulyana, C.

2017-05-01

The increasing in world population and the industrial sector led to increased demand for energy sources. To do this by utilizing the agricultural waste as a fuel source of alternative energy in the form of bio briquette. The aim at this study was to obtain data onto the characteristics of a wide variety of biomass briquettes from waste agricultural industry. The basic ingredients used are biomass waste from coconut husks, sawdust, rice husks and coffee husks. Each of these biomass residues are dried, crushed, then mixed with starch adhesives. This mixture is molded and dried using sunlight. Each type of briquettes was characterized and analyzed the physical-chemical properties, including calorific value, water content, fixed carbon content and the results were compared with charcoal and coal that was used as fuel in public. The results showed that bio briquettes from coconut husks get the highest calorific value of 4,451 cal/g.

Production of high-calorie energy briquettes from bark waste, plastic and oil

Science.gov (United States)

Suwinarti, W.; Amirta, R.; Yuliansyah

2018-04-01

Bark is the waste generated from the utilization of plantation timber, while plastics and oil waste are produced from daily human activity. These waste has the potential to be used as energy briquettes raw materials, especially for fuel in power plants. It would be worth very strategic for the environment and the welfare of society, considering that at this time we are not yet fully capable of well managing all three waste types. On the other hands most of the power plants that operate today still use diesel and coal as fuel. Therefore, the best composition of mixing bark, plastic and oil will be studied as well as its influence on the physical and chemical quality of the briquettes produced. The results show that the addition of the oil waste (70%) and used plastic (30%) as additive give effect to the performance of the briquette formation with the highest calorific value of 33.56 MJ/kg.

Combustion of Coal-Mule Briquettes / Spalanie Brykietów Z Mułu Węglowego

Science.gov (United States)

Kijo-Kleczkowska, Agnieszka

2013-09-01

Combustion technologies coal-mule fuels create a number of new possibilities for organising combustion processes so that they fulfil contemporary requirements (e.g., in terms of the environment protection- related issues). The paper describes the problems of coal-mule fuel combustion that have acquired a wider significance as the quality requirements of coal combustion in power plants have been growing. Coal mines that want to fulfill expectations of power industry workers have been forced to develop and modernize plants of coal wet cleaning. It all results in the growing amount of waste arising in the process of coal wet cleaning which contains smaller and smaller coal undersizes. In this situation the concept of direct combustion of the above mentioned waste and their co-combustion with other fuels, coal and biomass, seems to be attractive. Biomass is one from the most promising sources of renewable energy. The main aim of the paper is to identify the mechanism and kinetics of combustion of coal-mule fuels and their co- -combustion with coal and biomass in the briquettes form based on extensive experimental research in air. Niekorzystny bilans paliwowy naszego kraju powoduje nadmierne obciążenie środowiska, wywołane emisją CO2, NOx, SO2 i pyłów, a także powiększeniem powierzchni koniecznych na składowanie wciąż narastających stałych odpadów paleniskowych. Górnictwo, od którego energetyka oczekuje coraz lepszego paliwa, musi stosować głębsze wzbogacanie węgla. Powoduje to ciągłą produkcję odpadów w postaci mułów poflotacyjnych. Najlepszą metodą utylizacji tych mułów jest ich spalanie w postaci zawiesin, a także ich współspalanie z innymi paliwami, węglem czy biomasą. Biomasa jest bowiem jednym z najbardziej obiecujących źródeł OZE, a jej współspalanie z paliwami węglowymi znajduje w ostatnich latach coraz szersze zastosowanie zarówno w kraju, jak i na świecie. W tej sytuacji istotne jest prowadzenie badań naukowych

Briquetting of coal fines and sawdust - effect of particle-size distribution

Energy Technology Data Exchange (ETDEWEB)

Patil, D.P.; Taulbee, D.; Parekh, B.K.; Honaker, R. [University of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

2009-07-01

The coal industry usually discards fine-size (-150 microns) coal because of its high-moisture content and handling problems. One avenue for utilization is to either pelletize or briquette this material. However, industry has not adopted this route due in large part to significant drying and binder costs. In an effort to reduce these costs, compacting and briquetting studies were conducted to determine the effect of combining a coarse (1.18x0.15mm) spiral separator product with a fine coal flotation product (-150microns), with and without adding sawdust. Maximizing the packing density of the coal and wood waste mixture could potentially reduce the binder requirement by minimizing the void space as well as reducing shipping costs. Accordingly, work reported here focused on evaluating the impact of the particle-size distribution of different blends of fine and coarse coal, with and without sawdust and/or binder. The modified Proctor density of compacted blends along with the porosity and compressive strengths of briquettes made from each blend were determined. For the coal-only blends, the packing density was maximized by a relatively high (70% to 80%) coarse coal content. However, the packing density did not correlate with the compressive strength of the briquette that instead maximized with 100% fine flotation coal and continuously decreased as higher proportions of coarse coal were added. Similar compaction and compressive-strength results were obtained with mixtures of sawdust and varying proportions of coarse and fine coal. With the addition of a binder, the highest strengths were no longer obtained with 100% fine coal but instead maximized between 20% and 50% coarse coal addition depending on how long the briquettes were cured.

Obtention of charcoal briquettes from rice husks using low compaction pressure; Obtencao de briquetes de carvao vegetal de cascas de arroz utilizando baixa pressao de compactacao

Energy Technology Data Exchange (ETDEWEB)

Morais, Marcia R.; Seye, Omar; Freitas, Katrina T. de; Rodrigues, Monica; Santos, Eyde C.S. dos; Souza, Rubem C.R. [Universidade Federal do Amazonas (CDEAM/UFAM), Manaus, AM (Brazil). Centro de Desenvolvimento Energetico Amazonico

2006-07-01

This work consists of the preparation of briquette from carbonized rice's husks in low pressure. The results demonstrate are necessary a fine granulation of the rice's husks coal to obtainment of briquettes. The ultimate analysis of the briquette did not detect the presence of nitrogen and sulfur, and that prevents the formation and emission of acid gases that can produce corrosion in the equipment and pollute the atmosphere. The performance of the briquette production was superior to 80%. The briquettes present high heating value (HHV) 17,73 MJ/kg and adequate mechanic resistance for the use in gasifier-engine system. (author)

Basic investigations to improve the refinement process of coal. Grundlagenuntersuchungen zur Erhoehung des Veredlungsverhaltens von Kohlen

Energy Technology Data Exchange (ETDEWEB)

Krug, H; Naundorf, W; Trommer, D

1985-01-01

In the four articles in this issue, variants of the process for the effective use and improved refinement of brown coal are described. There are reports on the manufacture of special briquettes from briquette coal slack and on the briquetting behaviour of dry brown coal dust and the briquetting and coking behaviour of hard foreign brown coal containing a lot of ash. The four articles are dealt with separately. With 52 figs., 10 tabs.

Pyrolysis of biomass briquettes, modelling and experimental verification

NARCIS (Netherlands)

van der Aa, B; Lammers, G; Beenackers, AACM; Kopetz, H; Weber, T; Palz, W; Chartier, P; Ferrero, GL

1998-01-01

Carbonisation of biomass briquettes was studied using a dedicated single briquette carbonisation reactor. The reactor enabled continuous measurement of the briquette mass and continuous measurement of the radial temperature profile in the briquette. Furthermore pyrolysis gas production and

Sustainable energy development of bio briquettes based on rice husk blended materials: an alternative energy source

Science.gov (United States)

Suryaningsih, S.; Nurhilal, O.

2018-05-01

Rice husk as an abundant waste of biomass up to 21 million tons/year, it is unfortunate if it is not utilized. By converting it into bio briquettes, the value of rice husk bio briquettes in some studies before obtaining a relatively low value of 3,221-3,350 cal/g. The purpose of this research is to increase the calorific value of rice husk bio briquettes by mixing with coconut shell charcoal or corncob charcoal at various composition ratios of 50:50 and 80:20, to reach the optimal value that the industrial sector needed. Carbonization process was carried out at a temperature of 250-350 °C for 1.5 hours. From the results of the proximate analysis test using selected carbonization temperature at 300 °C, it can be seen that the best briquette value is made by mixing rice husk and coconut shell charcoal at composition ratio of 50:50, resulting 47.92% fixed carbon, 8.52% moisture content, 23.40% volatile matter and 20.16% ash content. The highest calorific value of 4,886 cal/g at ratio composition of 50:50, is slightly higher than the East Kalimantan coal standard of 4,828 cal/g. Hence, this bio briquettes are suitable for small scale industry application and household community use.

Influence of Storage on Briquettes Mechanical Properties

Directory of Open Access Journals (Sweden)

Brožek M.

2014-09-01

Full Text Available The effects of the storage place, placing manner, and storage time on mechanical properties of briquettes made from birch chips were laboratorily tested. A unique methodology developed by the present author enabling a relatively easy assessment of mechanical properties of the briquettes is described. The briquettes properties were evaluated by their density and rupture force determination. From the test results it follows that if the briquettes are stored in a well closed plastic bag, neither the place nor the storage time influence significantly their life time. When stored in a net plastic bag, the briquettes get seriously damaged, namely depending on their storage place and storage time.

Fine tuning of process parameters for improving briquette production from palm kernel shell gasification waste.

Science.gov (United States)

Bazargan, Alireza; Rough, Sarah L; McKay, Gordon

2018-04-01

Palm kernel shell biochars (PKSB) ejected as residues from a gasifier have been used for solid fuel briquette production. With this approach, palm kernel shells can be used for energy production twice: first, by producing rich syngas during gasification; second, by compacting the leftover residues from gasification into high calorific value briquettes. Herein, the process parameters for the manufacture of PKSB biomass briquettes via compaction are optimized. Two possible optimum process scenarios are considered. In the first, the compaction speed is increased from 0.5 to 10 mm/s, the compaction pressure is decreased from 80 Pa to 40 MPa, the retention time is reduced from 10 s to zero, and the starch binder content of the briquette is halved from 0.1 to 0.05 kg/kg. With these adjustments, the briquette production rate increases by more than 20-fold; hence capital and operational costs can be reduced and the service life of compaction equipment can be increased. The resulting product satisfactorily passes tensile (compressive) crushing strength and impact resistance tests. The second scenario involves reducing the starch weight content to 0.03 kg/kg, while reducing the compaction pressure to a value no lower than 60 MPa. Overall, in both cases, the PKSB biomass briquettes show excellent potential as a solid fuel with calorific values on par with good-quality coal. CHNS: carbon, hydrogen, nitrogen, sulfur; FFB: fresh fruit bunch(es); HHV: higher heating value [J/kg]; LHV: lower heating value [J/kg]; PKS: palm kernel shell(s); PKSB: palm kernel shell biochar(s); POME: palm oil mill effluent; RDF: refuse-derived fuel; TGA: thermogravimetric analysis.

Australia's export coal industry: a project of the Coal Australia Promotion Program. 2. ed.

International Nuclear Information System (INIS)

1995-01-01

This booklet presents an overview of the Australian coal industry, emphasises the advantages of using Australian coal and outlines government policies, both Commonwealth and State, which impact on coal mine development, mine ownership and coal exports. It also provides information on the operations and products of each producer supplying coal and coke to export markets and gives contact details for each. The emphasis is on black coal, but information on coal briquettes and coke is also provided. Basic information on the rail networks used for the haulage of export coal and on each of the bulk coal loading terminals is also included.(Author). 3 figs., photos

Analysis of briquetting process of sewage sludge with coal to combustion process

Directory of Open Access Journals (Sweden)

Kosturkiewicz Bogdan

2016-01-01

Full Text Available Energy recovery from sewage sludge can be achieved by several thermal technologies, but before those processes sewage sludge requires special pretreatment. The paper presents the investigation of the sewage sludge with coal briquettes as a fuel for combustion process. Research is conducted at Department of Manufacturing Systems and Department of Thermal Engineering and Environmental Protection, AGH University of Science and Technology to develop a technology of briquette preparation. The obtained results showed possibility of briquetting of municipal sewage sludge with coal in roll presses, equipped with asymmetric thickening gravity feed system. The following properties were determined for the obtained briquettes: density, drop strength and compressive strength. Based on physical and chemical analysis of prepared briquettes it was confirmed that briquettes have good fuel properties to combustion process. Thermal behaviour of studied sewage sludge and prepared mixture was investigated by thermogravimetric analysis (TG. For the thermo gravimetric analysis (TG the samples were heated in an alumina crucible from an ambient temperature up to 1000 °C at a constant rates: 10 °C/min, 40 °C/min and 100 °C/min in a 40 ml/min flow of air.

Fuel briquettes from brown coals of Yakutia

Energy Technology Data Exchange (ETDEWEB)

L.A. Nikolaeva; V.G. Latyshev; O.N. Burenina [Russian Academy of Sciences, Yakutsk (Russian Federation). Institute of Oil and Gas Problems

2009-04-15

Experimental data on the development of technology for the manufacture of briquetted fuel from brown coals with the use of various petroleum binders are presented. The influence of the moisture content, the coal particle-size composition, the binder type and concentration, the compacting pressure, and heat treatment regimes on the mechanical properties of the materials was studied. The optimal compositions and optimal values of the engineering parameters for the production of graded briquetted fuel from brown coals of the Kangalassy deposit in the Republic of Sakha (Yakutia) were established.

The use of fractionated fly ash of thermal power plants as binder for production of briquettes of coke breeze and dust

Science.gov (United States)

Temnikova, E. Yu; Bogomolov, A. R.; Lapin, A. A.

2017-11-01

In this paper, we propose to use the slag and ash material of thermal power plants (TPP) operating on pulverized coal fuel. The elemental and chemical composition of fly ash of five Kuzbass thermal power plants differs insignificantly from the composition of the mineral part of coking coal because coke production uses a charge, whose composition defines the main task: obtaining coke with the required parameters for production of iron and steel. These indicators are as follows: CRI reactivity and strength of the coke residue after reaction with CO2 - CSR. The chemical composition of fly ash of thermal power plants and microsilica with bulk density of 0.3-0.6 t/m3 generated at production of ferroalloys was compared. Fly ash and microsilica are the valuable raw material for production of mineral binder in manufacturing coke breeze briquettes (fraction of 2-10 mm) and dust (0-200 μm), generated in large quantities during coking (up to 40wt%). It is shown that this binder is necessary for production of smokeless briquettes with low reactivity, high strength and cost, demanded for production of cupola iron and melting the silicate materials, basaltic rocks in low-shaft furnaces. It is determined that microsilica contains up to 90% of silicon oxide, and fly ash contains up to 60% of silicon oxide and aluminum oxide of up to 20%. On average, the rest of fly ash composition consists of basic oxides. According to calculation by the VUKHIN formula, the basicity index of briquette changes significantly, when fly ash is introduced into briquette raw material component as a binder. The technology of coke briquette production on the basis of the non-magnetic fraction of TPP fly ash in the ratio from 3.5:1 to 4.5:1 (coke breeze : coke dust) with the addition of the binder component to 10% is proposed. The produced briquettes meet the requirements by CRI and require further study on CSR requirements.

Meditation on the construction of exemplar plant for briquetted coal gasification

Energy Technology Data Exchange (ETDEWEB)

Zhou Kuiyi [China National Coal Industry Import and Export Corporation, Beijing (China)

1997-12-31

China uses a considerable amount of anthracite, but the fines from anthracite mining are not sufficiently used. This project involved the construction of a plant for the manufacture of anthracite briquettes under high pressure, for use in gasification plants. The characteristics of the coals used and the types of briquette formed are described. 2 tabs.

Developing densification technology to facilitate briquetting of coal fines

Energy Technology Data Exchange (ETDEWEB)

Shi, R. [Ministry of Metallurgy (China). Anshan Thermal Energy Research Institute

1997-01-01

This paper introduces the densification technology in coal processing and the research of increasing the caking power of coal and its application. By exploiting the inherent caking property of coal, it is hoped to advance the briquetting technology so that coal fines is converted into high quality coke or briquette. This will produce very good social, economical and environmental benefit. 3 figs., 5 tabs.

Analysis of Calorific Value of Tibarau Cane Briquette

Science.gov (United States)

Nurdin, H.; Hasanuddin, H.; Darmawi, D.; Prasetya, F.

2018-04-01

The development of product diversification through tibarau cane briquettes as an effort in obtaining alternative fuels. Tibarau cane is one of the potential materials of renewable energy sources that can be processed into briquette. So as to reduce dependence on energy fuel oil, which for the middle to lower class is the main requirement. Efforts and innovations tibarau cane briquettes in producing fuel that has quality and performance can be measured with calorific value. Prior to development of this potential required the existence of test and evaluation stages according to the order of the flow of new material product development. Through process technology of briquette product making with compaction and optimization of composition content on tapioca adhesive and mesh particles suitable to get optimum calorific value. The results obtained in this research are the development of tibarau cane briquette model which is recommended as replacement fuel. Where the calorific value of tibarau cane briquette is 11.221,72 kJ / kg at composition percentage 80: 20 and its density is 0,565 gr/cm3. The comparison of mass tibarau with tapioca, particle size, pressure force (compaction), can affect the calorific value and density of tibarau cane briquette.

Use of an Individual Plant Examination (IPE) to enhance outage management

International Nuclear Information System (INIS)

Putney, B.; Averett, M.; Riley, J.

1992-10-01

A comparative emissions study was conducted on combustion products of various solid domestic cooking fuels; the objective was to compare relative levels of organic and inorganic toxic emissions from traditional Pakistani fuels (wood, wood charcoal, and dried animal dung) with manufactured low-rank coal briquettes (Lakhra and Sor-Range coals) under conditions simulating domestic cooking. A small combustion shed 12 m 3 internal volume, air exchange rate 14 h -1 was used to simulate south Asian cooking rooms. 200-g charges of the various fueb were ignited in an Angethi stove located inside the shed, then combusted to completion; effluents from this combustion were monitored as a function of time. Measurements were made of respirable particulates, volatile and semi-volatile organics, CO, SO 2 , and No x . Overall it appears that emissions from coal briquettes containing combustion amendments (slaked lime, clay, and potassium nitrate oxidizer) are no greater than emissions Erom traditional fuels, and in some cases are significantly lower; generally, emissions are highest for afl fuels in the early stages of combustion

Effect of process variables on the quality attributes of briquettes from wheat, oat, canola and barley

Energy Technology Data Exchange (ETDEWEB)

Jaya Shankar Tumuluru

2011-08-01

Effect of process variables on the quality attributes of briquettes from wheat, oat, canola and barley straw Jaya Shankar Tumuluru*, L. G. Tabil, Y. Song, K. L. Iroba and V. Meda Biomass is a renewable energy source and environmentally friendly substitute for fossil fuels such as coal and petroleum products. Major limitation of biomass for successful energy application is its low bulk density, which makes it very difficult and costly to transport and handle. To overcome this limitation, biomass has to be densified. The commonly used technologies for densification of biomass are pelletization and briquetting. Briquetting offers many advantages at it can densify larger particles sizes of biomass at higher moisture contents. Briquetting is influenced by a number of feedstock and process variables such as moisture content, particle size distribution, and some operating variables such as temperature and densification pressure. In the present study, experiments were designed and conducted based on Box-Behnken design to produce briquettes using barley, wheat, canola and barley straws. A laboratory scale hydraulic briquette press was used for the present study. The experimental process variables and their levels used in the present study were pressure levels (7.5, 10, 12.5 MPa), three levels of temperature (90, 110, 130 C), at three moisture content levels (9, 12, 15% w.b.), and three levels of particle size (19.1, 25.04, 31.75 mm). The quality variables studied includes moisture content, initial density and final briquette density after two weeks of storage, size distribution index and durability. The raw biomass was initially chopped and size reduced using a hammer mill. The ground biomass was conditioned at different moisture contents and was further densified using laboratory hydraulic press. For each treatment combination, ten briquettes were manufactured at a residence time of about 30 s after compression pressure setpoint was achieved. After compression, the initial

Production of charcoal briquettes from biomass for community use

Science.gov (United States)

Suttibak, S.; Loengbudnark, W.

2018-01-01

This article reports of a study on the production of charcoal briquettes from biomass for community use. Manufacture of charcoal briquettes was done using a briquette machine with a screw compressor. The aim of this research was to investigate the effects of biomass type upon the properties and performance of charcoal briquettes. The biomass samples used in this work were sugarcane bagasse (SB), cassava rhizomes (CR) and water hyacinth (WH) harvested in Udon Thani, Thailand. The char from biomass samples was produced in a 200-liter biomass incinerator. The resulting charcoal briquettes were characterized by measuring their properties and performance including moisture content, volatile matter, fixed carbon and ash contents, elemental composition, heating value, density, compressive strength and extinguishing time. The results showed that the charcoal briquettes from CR had more favorable properties and performance than charcoal briquettes from either SB or WH. The lower heating values (LHV) of the charcoal briquettes from SB, CR and WH were 26.67, 26.84 and 16.76 MJ/kg, respectively. The compressive strengths of charcoal briquettes from SB, CR and WH were 54.74, 80.84 and 40.99 kg/cm2, respectively. The results of this research can contribute to the promotion and development of cost-effective uses of agricultural residues. Additionally, it can assist communities in achieving sustainable self-sufficiency, which is in line with our late King Bhumibol’s economic sufficiency philosophy.

Pyrolysis Process and Characteristics of Products from Sawdust Briquettes

Directory of Open Access Journals (Sweden)

Hua Yang

2016-01-01

Full Text Available The pyrolysis of briquettes made from biomass is an available and economic technological route for the production of briquette charcoal, but by-products (tar and gas cannot be brought into full utilization, leading to the waste of resources and the addition of environmental concerns. Temperature is the most important parameter that affects the distributions and properties of briquette charcoal. This work investigated the three kinds of products of the pyrolysis of sawdust briquette in a fixed bed across a wide temperature range (250 to 950 °C. The purpose of this experiment was to study the pyrolysis process and the properties of the resulting products (briquette charcoal, liquid, and gas of sawdust briquettes and explore the optimum operating temperature to generate good quality briquette charcoal, liquid, and gaseous products simultaneously. According to the results, the optimum pyrolysis temperature range was 450 to 650 °C, for which the briquette charcoal produced within this range had the highest calorific value (2,9.14 to 30.21 MJ/kg. Meanwhile, the liquid product is considered to be useful for liquid fuels or valuable chemical materials, and the low heating value of the gaseous product was 11.79 to 14.85 MJ/Nm3 in this temperature range.

Combustion Characteristics Of Agricultural Waste-Coal Char Blends

International Nuclear Information System (INIS)

Akpabio, I. O; Danbature W

2002-01-01

Shortage of petroleum products, depletion of huge forest reserves for fuel purposes with its attendant erosion problems and other environmental considerations have necessitated investigations into other sources of fuel. In this wise. a set of seven types of briquettes were prepared from agricultural wastes such as rice husk, maize husk and saw-dust and blends of carbonized coal char. Strong and well-formed briquettes with good combustion characteristics were obtained. The results obtained from water boiling tests show that 2 litres of water could be boiled just under 23 minutes. Moisture contents and strengths of these briquettes were also determined and are discussed. The results show that wastes could be converted into useful fuel

Characterization of Briquette Produced from Tannery Solid Waste

Directory of Open Access Journals (Sweden)

Olatunde Ajani Oyelaran

2017-06-01

Full Text Available Skin processing produces large volumes of wastes, much of which are not utilized but disposed in the landfill. This study explored the possibility of producing briquettes from tannery waste that could be used for heating purposes for cottage factories and domestic cooking. Wastes studied are buffing dust, chrome shavings, fleshing, and hair. The briquette properties tested were moisture content, volatile matter, ash content, fixed carbon content, calorific value, compressive strength, density and durability. The moisture content of the raw materials ranged between 2.04 and 8.37% while the moisture content of the produced briquettes after 19 days of drying ranges between 1.17 and 4.13%. The volatile matter also decreases while the ash content increases after briquetting. The fixed carbon content ranges 73.79 and 93.23%. The heating values of the briquettes also showed a great increased after briquetting of between 19.82 and 21.86 MJ/kg. The compressive strength ranges between 0.17 and 0.21 kN/cm2, the durability ranges between 97.83 and 99.54%. The maximum densities of the briquettes also meet the required specifications of minimum value of 600 kg/m3. The briquettes produced also possess good qualities that make tannery solid waste a materials for production of briquettes for heating and in cottage industries

Development of environmentally friendly briquettes

International Nuclear Information System (INIS)

Kleisa, K.; Lehmann, J.; Verfuss, F.; Simon, G.

1994-01-01

The DMT has developed an industrial briquette consisting of about 87% hardcoal, 7% molasses pulp and 6% hydration limestone which meets the requirements of the clean air authority as an environmentally friendly fuel for travelling grate boilers. In extensive tests in a 4.4 MW travelling grate boiler these briquettes with molasses and limestone additives proved to be particularly effective in terms of reducing sulphur dioxide emission in the flue gas. They exhibited good ignition and combustion behaviour as well as a considerable reduction in nitrogen oxide emission. In a large-scale test with 1000 t of briquettes in a 46.5 MW travelling grate furnace it proved possible to confirm the good combustion behaviour and the reduced emission of sulphur oxide and nitrogen oxide in the flue gas. (orig.) [de

Process for converting coal into liquid fuel and metallurgical coke

Science.gov (United States)

Wolfe, Richard A.; Im, Chang J.; Wright, Robert E.

1994-01-01

A method of recovering coal liquids and producing metallurgical coke utilizes low ash, low sulfur coal as a parent for a coal char formed by pyrolysis with a volatile content of less than 8%. The char is briquetted and heated in an inert gas over a prescribed heat history to yield a high strength briquette with less than 2% volatile content.

Physico-chemical characteristics and market potential of sawdust charcoal briquette

Energy Technology Data Exchange (ETDEWEB)

Akowuah, Joseph O.; Kemausuor, Francis [Kwame Nkrumah Univ. of Science and Technology, Kumasi (Ghana). Dept. of Agricultural Engineering; Mitchual, Stephen J. [Univ. of Education, Winneba, Kumasi (Ghana). Dept. of Design and Technology Education

2012-11-01

In the absence of the widespread distribution of modern cooking fuels in developing countries, efforts are being made to utilise biomass residues which abound in most of these countries. This is intended to replace portions of firewood and charcoal and thereby reduce the cutting down of forests for fuel purposes. Briquettes from agro-residues have therefore been promoted as a better replacement to firewood and charcoals for heating, cooking and other industrial applications in both urban and rural communities. This study sought to assess the physico-chemical properties of charcoal briquettes produced in Ghana and also establish demand for and willingness of potential users to substitute charcoal and firewood with a charcoal briquette. A laboratory experiment was conducted to determine the physicochemical characteristics of the briquettes. This was done prior to the distribution of the briquette to potential users to collaborate their views or otherwise on the handling and burning characteristics of the charcoal briquette. A survey was undertaken a week later using questionnaires to access the willingness of the potential users to use the briquettes. Sixty respondents were purposively selected from households and the hospitality industry for the survey. Results of the physico-chemical assessment of the briquettes were as follows: length (75 to 120 mm), moisture content (5.7% dry basis), density (1.1 g/cm{sup 3}), ash content (2.6%), fixed carbon (20.7%), volatile matter (71%) and calorific value (4,820 kcal/kg). Responses from the survey indicated that the briquette is easy to ignite, has a long burning time and has good heat output. Respondents also observed that the briquettes did not give off sparks and had less smoke and ash content as compared to the regular charcoal they often used. Finally, 93% of the respondents indicated their willingness to use the briquettes if the price was comparable to charcoal. (orig.)

Using cotton plant residue to produce briquettes

Energy Technology Data Exchange (ETDEWEB)

Coates, W. [University of Arizona, Tucson, AZ (United States). Bioresources Research Facility

2000-07-01

In Arizona, cotton (Gossypium) plant residue left in the field following harvest must be buried to prevent it from serving as an overwintering site for insects such as the pink bollworm. Most tillage operations employed to incorporate the residue into the soil are energy intensive and often degrade soil structure. Trials showed that cotton plant residue could be incorporated with pecan shells to produce commercially acceptable briquettes. Pecan shell briquettes containing cotton residue rather than waste paper were slightly less durable, when made using equivalent weight mixtures and moisture contents. Proximate and ultimate analyses showed the only difference among briquette samples to be a higher ash content in those made using cotton plant residue. Briquettes made with paper demonstrated longer flame out time, and lower ash percentage, compared to those made with cotton plant residue. (author)

Effect of starch binder on charcoal briquette properties

Science.gov (United States)

Borowski, Gabriel; Stępniewski, Witold; Wójcik-Oliveira, Katarzyna

2017-10-01

The paper shows the results of a study on the effect of starch binder on the mechanical, physical and burning properties of charcoal briquettes. Two types of binders were repeatedly used to make briquettes of native wheat starch and modified wheat starch, at 8% of the whole. Briquetting was performed in a roller press unit, and pillow-shaped briquettes were made. The moisture of the mixed material ranged from 28 to 32%. The product, whether the former or the latter, was characterized by very good mechanical properties and satisfactory physical properties. Moreover, the type of starch binder had no effect on toughness, calorific heating value, volatiles, fixed carbon content and ash content. However, the combustion test showed quite different burning properties. As briquettes should have short firing up time and lower smokiness, as well as high maximum temperature and long burning time, we have concluded that briquettes with native wheat starch as a binder are more appropriate for burning in the grill.

Potency of bio-charcoal briquette from leather cassava tubers and industrial sludge

Science.gov (United States)

Citrasari, Nita; Pinatih, Tety A.; Kuncoro, Eko P.; Soegianto, Agoes; Salamun, Irawan, Bambang

2017-06-01

The purpose of this study was to determine the quality of the bio-charcoal briquette with materials from leather cassava tubers and sludge of wastewater treatment plant. The first, bio-charcoal briquette analized stability test and compressive strength. Then, bio-charcoal briquette with best value analyzed for parameter including moisture content, ash content, calorific content, and burned test. The result briquette quality based on compressive strength for bio-charcoal briquettes carbonated water content between 3.8%-4.5% and non-carbonated bio-charcoal briquettes between 5.2%-7.6%. Bio-charcoal carbonation briquette ash content was between 5.30%-7.40% and non-carbonated bio-charcoal briquettes was between 6.86%-7.46%. Bio-charcoal carbonation levels briquettes heated between 578.2 calories/g-1837.7 calories/g and non carbonatedbio-charcoal briquettes between 858.1 calories/g-891.1 calories/g. Carbonated bio-charcoal burned test was between 48-63 minutes and non-carbonated bio-charcoal was between 22-42 minutes. Emissions resulted from the bio-charcoal briquettes for carbonated and non carbonated composition according to the government regulations ESDM No. 047 of 2006 which, at 128 mg/Nm3 and 139 mg/Nm3.

Far-infrared irradiation drying behavior of typical biomass briquettes

International Nuclear Information System (INIS)

Chen, N.N.; Chen, M.Q.; Fu, B.A.; Song, J.J.

2017-01-01

Infrared radiation drying behaviors of four typical biomass briquettes (populus tomentosa leaves, cotton stalk, spent coffee grounds and eucalyptus bark) were investigated based on a lab-scale setup. The effect of radiation source temperatures (100–200 °C) on the far-infrared drying kinetics and heat transfer of the samples was addressed. As the temperature went up from 100 °C to 200 °C, the time required for the four biomass briquettes drying decreased by about 59–66%, and the average values of temperature for the four biomass briquettes increased by about 33–39 °C, while the average radiation heat transfer fluxes increased by about 3.3 times (3.7 times only for the leaves). The specific energy consumptions were 0.622–0.849 kW h kg"−"1. The Modified Midilli model had the better representing for the moisture ratio change of the briquettes. The values of the activation energy for the briquettes in the first falling rate stage were between 20.35 and 24.83 kJ mol"−"1, while those in the second falling rate stage were between 17.89 and 21.93 kJ mol"−"1. The activation energy for the eucalyptus bark briquette in two falling rate stages was the least one, and that for the cotton stalk briquette was less than that for the rest two briquettes. - Highlights: • Far infrared drying behaviors of four typical biomass briquettes were addressed. • The effect of radiation source temperatures on IR drying kinetics was stated. • Radiation heat transfer flux between the sample and heater was evaluated. • Midilli model had the better representing for the drying process of the samples.

The Swedish market for wood briquettes - Production and market development

Energy Technology Data Exchange (ETDEWEB)

Karlhager, Johan

2008-02-15

Wood briquettes have constituted an important input to the Swedish energy system during the last two decades. However, the development of the production and markets for briquettes during the years 2000-2007 has not been studied in detail. The purpose of this study was to elucidate the state of the briquette industry. More specifically, the aims were to map the production of briquettes, describe the development of its markets, describe the production process, describe the producers and to examine the competitive situation for the producers. To collect data regarding the production and the producers, the markets, raw materials and company structures, a questionnaire was sent out to the producers during the fall in the year 2007. The results were then compiled and compared to previous studies. The description of the production process was mainly based on literature studies. The results were analyzed and related to M.E. Porter's Five force model to be able to describe the competitive environment for the briquette producers. The study was limited to production in Sweden and did not intend to cover a possible import of briquettes. Regarding the production process, the most common types of briquetting equipment were described. The results showed that the trend in the briquette industry was neutral, possibly negative. The turnover derived from briquette sales during the year 2006 was roughly a quarter of a billion SEK. The industry was very concentrated, with one producer accounting for 43 % of the aggregate production in the year 2006. Since the year 2000, the production of briquettes among the participating producers increased from some 210 000 tons (980 GWh) (2002) to some 280 000 tons (1 300 GWh) in the year 2006. The planned expansion of the production capacity was 3,8 % within the two years to come. A typical small scale briquette producer was a small saw mill, planing mill or a joinery using their by-products as raw material. 78 % of the briquettes are produced

Fuel briquettes from wood and agricultural residues

Energy Technology Data Exchange (ETDEWEB)

Natividad, R.A.

1982-01-01

A short review of the production and uses of briquettes and of machinery available for briquetting fine dry, coarse dry and coarse wet raw materials. The potential of a fuel briquette industry in the Philippines with an estimated annual production of 217 million ton of sawdust, 2.09 billion ton of rice hulls and 2.87 million ton of coconut husks is discussed. Studies at the Forest Products Research and Development Institute (FPRDI) have shown that sawdust, coir dust rice hulls briquettes with 1-2% resin binder have heating values of 6882, 5839 and 3913 cal/g respectively.

combustion properties of briquettes produced from maize cob

African Journals Online (AJOL)

joke

2014-03-01

Mar 1, 2014 ... were densified into briquettes using starch as binder. Combustion related ... Keywords: Briquette, maize cob, combustion properties, mesh sizes, binding agent ... smaller space requirement for storage (Yaman et al., 2000 and ...

Economic, environmental and social assessment of briquette fuel from agricultural residues in China – A study on flat die briquetting using corn stalk

International Nuclear Information System (INIS)

Hu, Jianjun; Lei, Tingzhou; Wang, Zhiwei; Yan, Xiaoyu; Shi, Xinguang; Li, Zaifeng; He, Xiaofeng; Zhang, Quanguo

2014-01-01

Biomass can be relatively easily stored and transported compared with other types of renewable energy sources. Crop straw can be converted into densified solid biofuel via briquette fuel technology to expand its possible applications and enhance its utilisation efficiency. However, the potential economic, environmental and social impacts of crop straw briquette fuel need to be assessed before its large-scale use. This paper provides a comprehensive evaluation of these impacts for a fully-operating 2 × 10 4 t/a corn stalk briquette fuel plant in China. The results show that with a life time of 15 years, a purchase price of 150 RMB/t for corn stalk and the current sales price of 400 RMB/t for briquette fuel, the plant has a net present value of 9.6 million RMB or 1.5 million USD, an internal rate of return of 36% and a short investment payback period of 4.4 years. The life cycle greenhouse gas emissions are found to be 323 t CO 2 ,e/year or 1 kg CO 2 ,e/GJ, much lower than that of coal. Additionally, the process reduces pollution by decreasing the amount of corn stalk that is discarded or burnt directly in the field. In terms of social impacts, the use of corn stalk briquetting fuel plant is expected to play an important role in increasing local residents' income, improving rural ecological environments, alleviating energy shortages, guaranteeing energy security, and promoting socialism new rural reconstruction. - Highlights: • A fully-operating 2 × 10 4 t/a corn stalk briquette fuel plant in China is analysed. • The plant has net present value of $1.5 million and payback period of 4.4 years. • Life cycle GHG emissions are 323 t CO 2 ,e/year or 1 kg CO 2 ,e/GJ, much lower than coal. • The plant will also have significant social benefits

Coal development potential in Pakistan

Energy Technology Data Exchange (ETDEWEB)

Khan, M N; Pelofsky, A H [eds.

1986-01-01

A total of 48 papers were presented, and covered the following topics: the current situation in Pakistan with respect to development and utilization of coal resources; the policies that have been responsible for the development and utilization of coal resources in Pakistan; coal development and utilization in other developing nations e.g. Indonesia, Greece, Philippines, China, Thailand and Haiti; and technological developments in coal exploration; extraction, handling, transport and utilization which could accelerate future development of Pakistan's coal resources. Specific subjects covered include the use of coal in the cement industry of Pakistan; the production of briquettes for domestic use, development and training of personnel for the coal industry; and sources of finance for coal development projects. Particular emphasis is given throughout the conference to the Lakhra coal mine/power plant project which aims to develop and effectively utilize the lignite reserves of Sind Province. 47 papers have been abstracted separately.

Particle density determination of pellets and briquettes

Energy Technology Data Exchange (ETDEWEB)

Rabier, Fabienne; Temmerman, Michaeel [Centre wallon de Recherches agronomiques, Departement de Genie rural, CRA-W, Chaussee de Namur, 146, B 5030 Gembloux (Belgium); Boehm, Thorsten; Hartmann, Hans [Technologie und Foerderzentrum fuer Nachwachsende Rohstoffe, TFZ, Schulgasse 18, D 94315 Straubing (Germany); Daugbjerg Jensen, Peter [Forest and Landscape, The Royal Veterinary and Agricultural University, Rolighedsvej 23, DK 1958 Frederiksberg C (Denmark); Rathbauer, Josef [Bundesanstalt fuer Landtechnik, BLT, Rottenhauer Strasse,1 A 3250 Wieselburg (Austria); Carrasco, Juan; Fernandez, Miguel [Centro de investigaciones Energeticas, Medioambientales y Tecnologicas, CIEMAT, Avenida Complutense, 22 E 28040 Madrid (Spain)

2006-11-15

Several methods and procedures for the determination of particle density of pellets and briquettes were tested and evaluated. Round robin trials were organized involving five European laboratories, which measured the particle densities of 15 pellet and five briquette types. The test included stereometric methods, methods based on liquid displacement (hydrostatic and buoyancy) applying different procedures and one method based on solid displacement. From the results for both pellets and briquettes, it became clear that the application of a method based on either liquid or solid displacement (only tested on pellet samples) leads to an improved reproducibility compared to a stereometric method. For both, pellets and briquettes, the variability of measurements strongly depends on the fuel type itself. For briquettes, the three methods tested based on liquid displacement lead to similar results. A coating of the samples with paraffin did not improve the repeatability and the reproducibility. Determinations with pellets proved to be most reliable when the buoyancy method was applied using a wetting agent to reduce surface tensions without sample coating. This method gave the best values for repeatability and reproducibility, thus less replications are required to reach a given accuracy level. For wood pellets, the method based on solid displacement gave better values of repeatability, however, this instrument was tested at only one laboratory. (author)

comparative analysis of calorific value of briquettes produced

African Journals Online (AJOL)

yanky

4.30% at 40% starch level while Daniella oliveri + Rice husk briquettes at 20% starch level had the ... transportation, handling and storage (Husan et al. 2002). .... Table 1: Combustion Properties of Briquettes at 20% Starch Level. Biomass.

The effects of moderate die pressure on banana-peel briquettes

Energy Technology Data Exchange (ETDEWEB)

Wilaipon, P. [Khon Kaen Univ., Khon Kaen (Thailand). Faculty of Engineering]|[Narasuan Univ., Phitsanulok (Thailand). Faculty of Engineering; Trirattanasirichai, K.; Tangchaichit, K. [Khon Kaen Univ., Khon Kaen (Thailand). Faculty of Engineering

2006-07-01

Bananas are one of the most important crops in Thailand, and are now being considered as a renewable energy source. This study investigated the impacts of moderate die pressure on banana peel briquettes. The pressure range in the study was set at 3-11 MPa. Water resistance characteristics were also analyzed. Four factors were considered: (1) the relaxation in length of the briquettes; (2) impact resistance; (3) relaxation in volume; and (4) water resistance. Experiments were conducted in laboratory conditions with humidity set at between 50 and 60 per cent at 27 degrees C. An impact resistance test was performed 168 hours after the briquetting process. The briquettes were immersed in water in order to conduct the water resistance test. Results of the tests demonstrated a rapid increase in the length of the briquettes. The maximum percentage of elongation occurred within 1 hour after being removed from the die. Results of the strength tests showed that the briquettes had a compaction pressure over 5 MPa. The briquettes showed significant potential as a biomass fuel. 15 refs., 1 tab., 12 figs.

Feasibility study of environmentally friendly type coal utilization systems. Feasibility study of environmentally friendly type coal utilization systems in sectors except the coal industry in China; Kankyo chowagata sekitan riyo system kanosei chosa. Chugoku no sekitan kogyo igai no bumon ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of working out a comprehensive master plan for application of the coal utilization system, the paper surveyed and studied the coal utilization system in terms of environmental measures and efficiency improvement in the utilization of coal. As a result of the discussion with NEDO and the National Planning Committee of China, Liaoning Province (the whole China) and Shenyang City were selected as a model area and a model city for the survey and study. As energy conservation measures taken in the former, desirable are intensifying/capacity-increase of boilers, kilns, etc. and adoption of new-type/high-efficient equipment. Also expected are reinforcement of combustion control and improvement of efficiency by using coal preparation, industrial use coal briquette, etc. Measures taken in the latter are the same as those taken in the whole China. As SOx reduction measures for Liaoning Province, desirable is installation of dry-type desulfurization equipment and simple desulfurization equipment. As dust prevention measures for it, desirable is installation of electrostatic precipitators or high-functional bag filters. SOx reduction measures for Shenyang City are the same as those taken in the whole China. SOx can be reduced by using coal-prepared low-sulfur coal and industrial use coal briquette added with desulfurizing agent. 88 figs., 163 tabs.

Comparative study of durability test methods for pellets and briquettes

Energy Technology Data Exchange (ETDEWEB)

Temmerman, Michaeel; Rabier, Fabienne [Centre wallon de Recherches agronomiques (CRA-W), 146, chaussee de Namur, B-5030, Gembloux (Belgium); Jensen, Peter Daugbjerg [Forest and Landscape, The Royal Veterinary and Agricultural University, Rolighedsvej 23, DK-1958 Frederiksberg C (Denmark); Hartmann, Hans; Boehm, Thorsten [Technologie- und Foerderzentrum fuer Nachwachsende Rohstoffe-TFZ, Schulgasse 18, D-94315 Straubing (Germany)

2006-11-15

Different methods for the determination of the mechanical durability (DU) of pellets and briquettes were compared by international round robin tests including different laboratories. The DUs of five briquette and 26 pellet types were determined. For briquettes, different rotation numbers of a prototype tumbler and a calculated DU index are compared. For pellets testing, the study compares two standard methods, a tumbling device according to ASAE S 269.4, the Lignotester according to ONORM M 7135 and a second tumbling method with a prototype tumbler. For the tested methods, the repeatability, the reproducibility and the required minimum number of replications to achieve given accuracy levels were calculated. Additionally, this study evaluates the relation between DU and particle density. The results show for both pellets and briquettes, that the measured DU values and their variability are influenced by the applied method. Moreover, the variability of the results depend on the biofuel itself. For briquettes of DU above 90%, five replications lead to an accuracy of 2%, while 39 replications are needed to achieve an accuracy of 10%, when briquettes of DU below 90% are tested. For pellets, the tumbling device described by the ASAE standard allows to reach acceptable accuracy levels (1%) with a limited number of replications. Finally, for the tested pellets and briquettes no relation between DU and particle density was found. (author)

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

Combustion behavior of briquettes from oil palm's empty fruit bunch

Energy Technology Data Exchange (ETDEWEB)

Pratoto, A. [Andalas Univ., Padang (Indonesia). Dept. of Mechanical Engineering

2006-07-01

Empty fruit bunch (EFB) briquettes from palm plantations are now being considered as a renewable energy source in Indonesia. This paper provided details of a study that investigated the combustion behaviour of an EFB briquette. Thermogravimetry was used to study the briquettes under dynamic conditions at 50 degrees C in a muffle furnace. Thermal decomposition rates and phases were identified, and the effect of the briquette's size on the decomposition rate was evaluated by comparing the combustion behaviour of the briquette to that of loose EFB materials. Rates of devolatilization and char oxidation were also examined. Results of the derivative thermogravimetry (DTG) analysis showed that larger briquettes did not exhibit a sharp peak on the DTG curve. Results suggested that heat transfer was predominant over the kinetic reaction during combustion. The ignition temperature of the briquettes was comparable to typical lignocellulose biomass. Peak combustion temperatures for loose EFB were only slightly lower than other types of biomass. Maximum combustion rates decreased with the size of the fuel. It was concluded that small briquettes are suitable for applications where high rates of heat are required. 16 refs., 1 tab., 6 figs.

Biomass-derived carbonaceous materials as components in wood briquettes

Energy Technology Data Exchange (ETDEWEB)

Stengl, S.; Koch, C.; Stadlbauer, E.A.; Scheer, J. [Univ. of Applied Sciences, THM Campus Giessen, Giessen (Germany); Weber, B. [Instituto de Ingenieria de la Universidad Nacional Autonoma de Mexico (UNAM), Coyoacan (Mexico); Strohal, U.; Fey, J. [Strohal Anlagenbau, Staufenberg (Germany)

2012-11-01

The present paper describes a briquette composed of a substantial amount of wooden biomass and up to 35% of carbonaceous materials derived from biogenic residues. The cellulosic component may be a mixture of any wooden residue. Suitable substrates for the carbonaceous fraction are vegetation wastes from land management or agriculture. Depending on physical and chemical nature of the substrate, Hydrothermal Carbonisation (HTC) or Low Temperature Conversion (LTC) may be used to produce the carbonaceous part of the briquette. HTC turns wet biomass at temperatures around 200 deg C in an autoclave into lignite whereas LTC treatment at 400 deg C and atmospheric pressure produces black coal. This is manifested by a molar ratio of 0.1 {<=} H/C (LTC) {<=} 0.7; 0.05{<=} O/C (LTC) {<=} 0.4 and 0.7 < H/C (HTC) <1.5 ; 0.2< O/C (HTC) < 0.5. Solid state {sup 13}C-NMR confirms these findings showing a strong absorption band for sp{sup 2}-hybridized carbon atoms at chemical shifts of 100 ppm und 165 ppm for LTC biochar. Depending on the substrate, HTC gives rise to an increase in the specific calorific value (MJ/kg) by a factor of {Psi} {approx} 1.2 - 1.4; LTC by 1.5 - 1.8. In addition ash melting points are significantly increased; in case of wheat straw by about 200 deg C. Compacted products may have a cylindrical or rectangular profile.

Converting Biomass and Waste Plastic to Solid Fuel Briquettes

Directory of Open Access Journals (Sweden)

F. Zannikos

2013-01-01

Full Text Available This work examines the production of briquettes for household use from biomass in combination with plastic materials from different sources. Additionally, the combustion characteristics of the briquettes in a common open fireplace were studied. It is clear that the geometry of the briquettes has no influence on the smoke emissions. When the briquettes have a small amount of polyethylene terephthalate (PET, the behavior in the combustion is steadier because of the increase of oxygen supply. The smoke levels are between the 3rd and 4th grades of the smoke number scale. Measuring the carbon monoxide emission, it was observed that the burning of the plastic in the mixture with biomass increases the carbon monoxide emissions from 10% to 30% as compared to carbon monoxide emission from sawdust biomass emissions which was used as a reference.

Effects of consumer subsidy on household fuel switching from coal to cleaner fuels: A case study for anthracites in Korea

International Nuclear Information System (INIS)

Park, Hojeong; Kwon, Hyucksoo

2011-01-01

The Korean coal industry is in a transition under low carbon policy through the steady reduction of coal production. Since consumer subsidy for the consumption of anthracites briquette in low-income households caused a distortion in domestic coal market, the so-called coupon program will be the first target in energy reform policy in order to induce fuel switching from anthracites to alternative clean energy. This paper tries to identify various factors that influence households' fuel switching decision. Disutility from briquette consumption is also considered as an important factor. Using the 2007 census data on briquette-consuming households, it is found that the coupon program provides an adverse effect to switching fuels to clean energy while the disutility of briquettes is positively associated with the probability of fuel switching. However, the empirical finding suggests that the policy alone attempting to remove coupon program may fail to switch fuels unless the cost of boiler changes is substantially reduced through the provision of accessible networks to alternative energy sources. It indicates that reform policy for consumer subsidy must be understood in line with more comprehensive regional energy plans to resolve energy poverty issue. - Research highlights: → Various factors are identified for low income households' fuel switching from coal to clean energy. → Coupon program and accessibility to alternative energy sources are considered; Result shows that accessible network to alternative clean energy sources is essential for low income group. → More comprehensive regional energy plans are required to resolve energy poverty issue.

Statistical summary of coal mining, coking, and briquetting plants and review of the solid fuels market in 1976

Energy Technology Data Exchange (ETDEWEB)

Medaets, J

1977-05-01

This paper reviews the activities of the Belgian coal and coke industry noting that some of the figures are still provisional. Figures are given for production and stocks of coal; personnel; productivity; working hours; salaries; and the production of coke and briquettes.

Water-Sensitivity Characteristics of Briquettes Made from High-Rank Coal

Directory of Open Access Journals (Sweden)

Geng Yunguang

2016-01-01

Full Text Available In order to study the water sensitivity characteristics of the coalbed methane (CBM reservoir in the southern Qinshui Basin, the scanning electron microscopy, mineral composition and the water sensitivity of main coalbed 3 cores were tested and analyzed. Because CBM reservoirs in this area are characterized by low porosity and low permeability, the common water sensitivity experiment of cores can’t be used, instead, the briquettes were chose for the test to analysis the water sensitivity of CBM reservoirs. Results show that: the degree of water sensitivity in the study area varies from week to moderate. The controlling factors of water sensitivity are clay mineral content and the occurrence type of clay minerals, permeability and liquid flow rate. The water sensitivity damage rate is positively correlated with clay mineral content and liquid flow rate, and is negatively correlated with core permeability. The water sensitivity of CBM reservoir exist two damage mechanisms, including static permeability decline caused by clay mineral hydration dilatation and dynamic permeability decline caused by dispersion/migration of clay minerals.

Effect of Briquetting Process Variables on Hygroscopic Property of Water Hyacinth Briquettes

Directory of Open Access Journals (Sweden)

R. M. Davies

2013-01-01

Full Text Available The knowledge of water resistance capacity of briquettes is important in order to determine how sensitive the produced briquettes are to moisture change during storage. The relative changes in length and diameter of briquettes during immersion in water for 6 hours were investigated. This was conducted to determine hygroscopic property of produced briquettes under process variables levels of binder (10, 20, 30, 40, and 50% by weight of residue, compaction pressure (3.0, 5.0, 7.0, and 9.0 MPa and particle size (0.5, 1.6, and 4 mm of dried and ground water hyacinth. Data was statistically analysed using Analysis of Variance, the Duncan Multiple Range Test, and descriptive statistics. The relative change in length of briquettes with process variables ranged significantly from % to % (binder, % to % (compaction pressure, and % to % (particle size (. Furthermore, the relative change in diameter of briquettes with binder, compaction pressure, and particle size varied significantly from % to %, % to %, and % to %, respectively (. This study suggests optimum process variables required to produce briquettes of high water resistance capacity for humid environments like the Niger Delta, Nigeria, as 50% (binder proportion, 9 MPa (compaction pressure, and 0.5 mm (particle size.

Clean coal technology challenges for China

Energy Technology Data Exchange (ETDEWEB)

Mao, J. [Tsinghua University, Beijing (China). Dept. of Thermal Engineering

2001-01-01

China is rich in coal reserves and also the largest coal producer and consumer in the world. Coal constitutes over 70% of the total energy consumption, some 86% of coal production is burned directly, which causes serious air pollution problems. However, based on China's specific energy structure, coal utilisation will remain the dominant means of energy usage and clean coal technology must be the way forward if the environmental problems are to be resolved. This article discusses China's Clean Coal Technology Program, its implementation, including the clean coal technologies being developed and introduced, with reference to the key R & D institutes for each of the coal-using sectors. The article is an edited version of the 2000 Robens Coal Science Lecture, delivered in London in October 2000. The China Coal Technology Program for the 9th Five-Year Plan (1996-2000) was approved in 1997. The technologies included in the Program considered in this article are in: coal washing and grading, coal briquette, coal water slurry; circulating fluidised bed technology; pressurised fluidised bed combined cycle; integrated gasification combined cycle; coal gasification, coal liquefaction and flue gas desulfurisation. 4 tabs.

A Novel Technique for Making Cold Briquettes for Charging in Blast Furnace

International Nuclear Information System (INIS)

Mohanty, M K; Mishra, S; Sarkar, S; Samal, S K; Mishra, B

2016-01-01

Different metallurgical wastes are generated during pyro processing of iron ore, which is used for making sponge iron or hot metal and for producing steel. Apart from these wastes, coke fines are generated during the coke making, and iron ore fines are generated during mining of iron ore. Although iron ore fines are used for making pellet after beneficiation still, it generates a huge quantity of iron ore waste during beneficiation with comparatively lower iron content. In the present study, briquettes are made by a stiff extrusion process from metallurgical waste like iron ore fines and coke fines with the addition of Portland cement as a binder and clay as a rheology modifier. Physical properties of the briquettes are evaluated, and reducibility of the briquettes is studied in comparison to lumpy iron ore. Phase analysis and microstructural analysis of the briquettes and lumpy iron ore are carried out after firing at different temperatures in the simulated blast furnace condition. Physical and mineralogical properties are correlated with the reducibility of the briquettes and lumpy iron ore. Briquettes made by a stiff extrusion process show a better mechanical strength fired at a different temperature to take the load of burden and better reducibility than lumpy iron ore. The briquettes after self-curing are charged to a 23 mt3 blast furnace which shows encouraging results. (paper)

Influence of Production Variables on Eco-Friendly Briquettes from Coconut and Bambara Nut Shells

Directory of Open Access Journals (Sweden)

O. A. Sotannde

2017-08-01

Full Text Available This study investigates the influence of production variables on the properties of molasses-induced fuel briquettes from Coconut (Cocos nucifera L. and Bambara nut (Vigna subterranea L. Verdc. shells. The milled samples of both raw materials were mixed with molasses at ratios 100:20, 100:25, 100:30 and 100:35 by weight respectively, and briquetted using a Jack press at an average pressure of 1.2KN/m2. A 3x4 factorial experiment in completely randomized design was used. The briquettes produced were subjected to both physical and combustion tests. The tests revealed that majority of the variations in briquette properties were largely influenced by the type of biomass residues used while molasses’ content also contributed significant effect atp < 0.05. Coconut shell briquettes had higher compressed density though lower in relaxed form (0.80 g·cm-3vs 0.78 g·cm-3 when compared to Bambara nut shell briquettes (0.77 g.cm-3vs0.75 g.cm-3. Both physical and combustion properties were significantly improved when both bio-residue mixtures were used. Briquettes from the mixtures had the highest average fixed carbon and heating values of 85.21% and 32.80 MJ·kg-1 respectively, though it was 83.83% and 32.12 MJ·kg-1for coconut shell briquette and 82.18% and 32.03 MJ·kg-1for Bambara nut shell briquette. Therefore, based on physical and combustion characteristics, the best Bambara nut briquettes and its mixture with coconut shell were produced when molasses content was 30%. In contrast, the best coconut shell briquette was produced when molasses content was 35%. These two level are therefore recommended for production of quality briquettes from these agro-residues.

DESIGN OF GRASS BRIQUETTE MACHINE

African Journals Online (AJOL)

user

E-mail addresses: 1 mike.ajieh@gmail.com, 2 dracigboanugo@yahoo.com, ... machine design was considered for processing biomass of grass origin. The machine operations include pulverization, compaction and extrusion of the briquettes.

Biomass Briquette Investigation from Pterocarpus Indicus Leaves Waste as an Alternative Renewable Energy

Science.gov (United States)

Anggono, Willyanto; Sutrisno; Suprianto, Fandi D.; Evander, Jovian

2017-10-01

Indonesia is a tropical country located in Southeast Asia. Indonesia has a lot of variety of plant species which are very useful for life. Pterocarpus indicus are commonly used as greening and easily found everywhere in Surabaya city because of its characteristics that they have dense leaves and rapid growth. Pterocarpus indicus leaves waste would be a problem for residents of Surabaya and disturbing the cleanliness of the Surabaya city. Therefore, the Pterocarpus indicus leaves waste would be used as biomass briquettes. This research investigated the calorific value of biomass briquettes from the Pterocarpus indicus leaves waste, the effect of tapioca as an adhesive material to the calorific value of biomass briquettes from the Pterocarpus indicus leaves waste, the optimum composition for Pterocarpus indicus leaves waste biomass briquette as an alternative renewable fuel and the property of the optimum resulted biomass briquette using ultimate analysis and proximate analysis based on the ASTM standard. The calorific value biomass briquettes from the Pterocarpus indicus leaves waste were performed using an oxygen bomb calorimeter at various composition of Pterocarpus indicus from 50% to 90% rising by 10% for each experiment. The experimental results showed that the 90% raw materials (Pterocarpus indicus leaves waste)-10% adhesive materials (tapioca) mixtures is the optimum composition for biomass briquette Pterocarpus indicus leaves waste. The lower the percentage of the mass of tapioca in the biomass briquettes, the higher calorific value generated.

Organic matter fuel briquettes as a forest conservation tool in Lake ...

African Journals Online (AJOL)

Organic matter fuel briquettes as a forest conservation tool in Lake Malawi National Park: research note. ... Open Access DOWNLOAD FULL TEXT ... towards fuel briquettes, cost is the limiting factor when people choose their fuel source.

Effect of Binder on Combustion Quality on EFB Bio-briquettes

Science.gov (United States)

Handra, Nofriady; Hafni

2017-12-01

Energy demand in various sectors in Indonesia has increased in line with the rate of population growth and the national economy. Fulfillment of energy needs can be obtained from various energy sources such as fuel oil, solar, biomass, wind, water and others. So far, energy sources used in Indonesia are still using many non-renewable energy sources, such as fuel oil. The utilization of waste from empty palm oil bunches into bio-briquettes has helped the government in overcoming the problem of EFB waste. The availability of biomass has prompted researchers to utilize biomass waste that includes Agricultural and Forestry waste, to be processed into briquettes as an alternative energy substitute for fuel oil. This research aims to improve the utilization of waste of Palm Oil Bunches through the manufacture of bio-briquette as alternative fuel and determine the appropriate binder material for briquette making so as to produce optimal combustion value. The binders used for the manufacture of briquettes are pine sap and starch flour. The test result showed that the highest value of calorific was found in the mixture of 50% EFB composition with fibre size ± 1-5 mm with 50% pine resin which is 6331,7 cal/g. Meanwhile, lowest value on EFB ± with fibre size 5-10 mm composition EFB 60% and 40% starch flour binder that is 2295,7 cal/g. The results of a flame test study of several points that are known to turn on until it emits a flame for ± 30 seconds, it takes 22,2 minutes for the burnt-out briquette (to ashes). Based on visual observations that the fire colour of bio-briquette with finer fibre on the EFB composition 50% pine gum binder produces a bluish red fire colour. It is generally assumed that pine resin glues produce better fuel value compared to starch binder. Besides that, fibre particles size also affects the combustion quality produced.

Strength of briquettes made of Cu concentrate and carbon-bearing materials

Directory of Open Access Journals (Sweden)

B. Oleksiak

2015-01-01

Full Text Available In the present paper, results of the research on application of residual fine-grained, carbon-bearing materials as coke substitutes in the shaft process of copper matter smelting are discussed. The addition was introduced into the charge as a component of concentrate-made briquettes, then, its effects on properties of the obtained briquettes were analysed for their compressive and drop strengths. The results of investigations confirmed the potential use of proposed alternative fuels (as briquette components in the process of copper matte smelting.

Peat briquette as an alternative to cooking fuel: A techno-economic viability assessment in Rwanda

International Nuclear Information System (INIS)

Hakizimana, Jean de Dieu K.; Kim, Hyung-Taek

2016-01-01

Commercialization of peat briquetting technology was analyzed to know whether the technology is economically viable or not compared to commercialization of charcoal. The investigation of economic viability was assessed from raw-peat production to briquetting technologies. The briquettes were made by naturally dried of peat from Bisika, Bahimba, Ndongozi and Nyirabirande bogs, through a rotary pulverizer and a briquette press; they were carbonized into furnace at 450 °C to reduce its health effects. The burning rate of peat briquettes made varied from 0.178 kg/hour to 0.222 kg/hour. Ash content varying between 3 and 7.2 percent was also observed. The results showed that peat briquettes can be sold at USD0.18 per unit, with a total NPV of USD17.2 million. However, as the NPV tends to be zero, the selling price would be approximately USD0.155 per briquette. Monthly charcoal expenses were about USD23.20/household compared to a per-household cost of USD16.20/month of peat briquettes consumption; the supplanting of charcoal by peat briquettes would help the average Rwandan household reduce its monthly expenses by 30 percent. Peat briquettes utilization as cooking fuel in Rwanda could save 0.05 percent of CO_2 and more than 99 percent of CH_4 emissions, compared to charcoal emissions. - Highlights: • A technical process for peat production and peat briquetting. • An efficiency test of carbonized briquettes. • Commercialization of peat briquettes is compared to commercialization of charcoal. • Opportunities for greenhouse gas emissions reduction.

Uranium briquettes for irradiation target

Energy Technology Data Exchange (ETDEWEB)

Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo, E-mail: saliba@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce {sup 99}Mo-{sup 99m}Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl{sub x} dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of {sup 235}U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

Uranium briquettes for irradiation target

International Nuclear Information System (INIS)

Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo

2011-01-01

Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce 99 Mo- 99m Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl x dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of 235 U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

Coal derivates for reduction of SO{sub 2} N0{sub x}; Derivados del Carbon para la Reduccion de SO{sub 2}-NO{sub x}

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The project was divided in two well-differentiated parts: SO{sub 2} removal and NO{sub x} reduction. In both cases, carbon materials play a unique role in the processes, either as calcium sorbent support (SO{sub 2} removal) or as catalyst support and reducing agent (NO{sub x} reduction). Removal of SO{sub 2}. This process was carried out by calcium sorbents at relatively low temperature (T<300 degree centigree), forming CaSO{sub 3} (instead of CaSO{sub 4}) that decomposes at lower temperatures, making regeneration easier. High dispersion of the active species, CaO, has been obtained using carbon materials (activated carbons, chars, etc) and other inorganic compounds as supports. The effect of oxygen, carbon dioxide and steam in the reaction atmosphere and the regeneration process have been also investigated. Thermal regeneration is possible for several cycles, however, carbon gasification also takes place. To control, and to void that effect the reaction and regeneration temperatures should be carefully controlled and carbons with low reactivity should be selected. The process was scaled (100-2000) using briquette samples obtained by physical mixture of char and Ca(OH){sub 2}. The SO{sub 2} removal levels were similar to those found in the laboratory scale. NO{sub x} reduction. The possibility of using potassium containing coal-briquettes for NO and NO{sub x} reduction has been investigated. The preparation method of briquettes presents the advantage of using a binder agent (humic acid) which contains the catalyst (potassium). The system catalyst-binder-coal stays intimately joined by a moulding stage and subsequent pyrolysis, providing proper mechanical resistance to the coal-briquettes. With the purpose to improve the briquettes activity, different variables of the preparation process have been investigated (potassium content-added with the binder and/or KOH-. rank and mineral matter content of the coal precursor, pyrolysis temperature and pressure of the

Preparation and Optimization of Vanadium Titanomagnetite Carbon Composite Hot Briquette: A New Type of Blast Furnace Burden

Science.gov (United States)

Zhao, W.; Wang, H. T.; Liu, Z. G.; Chu, M. S.; Ying, Z. W.; Tang, J.

2017-10-01

A new type of blast furnace burden, named VTM-CCB (vanadium titanomagnetite carbon composite hot briquette), is proposed and optimized in this paper. The preparation process of VTM-CCB includes two components, hot briquetting and heat treatment. The hot-briquetting and heat-treatment parameters are systematically optimized based on the Taguchi method and single-factor experiment. The optimized preparation parameters of VTM-CCB include a hot-briquetting temperature of 300°C, a coal particle size of coal-added ratio of 28.52%, a heat-treatment temperature of 500°C and a heat-treatment time of 3 h. The compressive strength of VTM-CCB, based on the optimized parameters, reaches 2450 N, which meets the requirement of blast furnace ironmaking. These integrated parameters provide a theoretical basis for the production and application of a blast furnace smelting VTM-CCB.

Fabrication and characterization of rice husk charcoal bio briquettes

Science.gov (United States)

Suryaningsih, S.; Nurhilal, O.; Yuliah, Y.; Salsabila, E.

2018-02-01

Rice husk is the outermost part of the rice seed which is a hard layer and a waste material from rice milling. Rice husk includes biomass that can be exploited for various requirements such as industrial raw materials as well as energy sources or fuel but only a small group of people use it. This research is conducted utilizing the rice husk as an alternative fuel by making it as a charcoal briquette. To make the treatment easy, firstly the rice husk biomass was converted into charcoal powder by carbonization method using two kinds of furnace which have different heating behavior. The best carbonization results are obtained from the furnace, which has a constant temperature heating behavior. The process of making briquettes is prepared by adding tapioca starch of 6% concentration by weight as charcoal adhesive and then printed with the aid of pressing tools using loads at 1,000 kg/cm2. The resulting briquette has a calorific value about 3.126 cal/g, mass density is 0.86 g/cm3 and compressive strength is about 2.02 kg/cm2, so that the bio-briquette of charcoal produced can be used as alternative energy to replace the fossil fuel for domestic or household purposes.

Thermal Properties of Green Fuel Briquettes from Residue Corncobs Materials Mixed Macadamia Shell Charcoal Powder

Science.gov (United States)

Teeta, Suminya; Nachaisin, Mali; Wanish, Suchana

2017-09-01

The objective of this research was to produce green fuel briquettes from corncobs by adding macadamia shell charcoal powder. The study was sectioned into 3 parts: 1) Quality improvement of green fuel briquettes by adding macadamia; 2) Fuel property analysis based on ASTM standards and thermal fuel efficiency; and 3) Economics appropriateness in producing green fuel briquettes. This research produced green fuel briquettes using the ratio of corncobs weight and macadamia shell charcoal powder in 100:0 90:10 80:20 70:30 60:40 and 50:50 and pressing in the cold briquette machine. Fuel property analysis showed that green fuel briquettes at the ratio 50:50 produced maximum heating values at 21.06 Megajoule per kilogram and briquette density of 725.18 kilograms per cubic meter, but the percent of moisture content, volatile matter, ash, and fixed carbon were 10.09, 83.02, 2.17 and 4.72 respectively. The thermal efficiency of green fuel briquettes averaged 20.22%. Economics appropriateness was most effective where the ratio of corncobs weight to macadamia shell charcoal powder was at 50:50 which accounted for the cost per kilogram at 5.75 Baht. The net present value was at 1,791.25 Baht. Internal rate of return was at 8.62 and durations for a payback period of investment was at 1.9 years which was suitable for investment.

Development of Briquette from Coir Dust and Rice Husk Blend: An Alternative Energy Source

Directory of Open Access Journals (Sweden)

Md. Hamidul Islam

2014-05-01

Full Text Available Biomass is one of the predominant renewable energy sources and the use of biomass for the energy generation has got much attention due to its environmental friendliness. Densification of coir dust into fuel briquette can solve waste disposal problem as well as can serve as an alternative energy source. The objective of this study was to investigate the possibility of producing briquette from coir dust and rice husk blend without binder. During this study, a briquetting experiment was conducted with different coir dust and rice husk blends (i.e. coir dust and rice husk ratio of 80:20, 60:40, 50:50, 40:60, 20:80 and 0:100. Briquetting operation was performed using a die-screw press type briquetting machine. The briquettes were tested to evaluate their density, compressive strength, calorific value, burning rate and water vaporizing capacity and it was found that mixing ratio had a significant effect on the physical, mechanical and combustion properties of the coir dust-rice husk briquettes. Density, compressive strength and calorific value and water vaporizing capacity were increased with increasing mixing ratio while burning rate was decreased. Coir dust-rice husk briquettes with mixing ratio of 20:80 had higher density (1.413 g/cm3, compressive strength (218.4 N/cm2, calorific value (4879 kcal/kg, water vaporizing capacity (0.853 l/kg and low burning rate (0.783 kg/hour followed by the mixing ratio 40:60, 50:50, 60:40 and 0:100. The results indicate that coir dust and rice husk blend briquettes were found to have better overall handling characteristics over rice husk briquette. However, production of briquettes from coir dust and rice husk at mixing ratio of 50:50 was found to be more suitable for commercial application in terms of cost effectiveness.

Forest-biological erosion control on coal-mine spoil banks in Bulgaria

International Nuclear Information System (INIS)

Haigh, M.J.; Gentcheva-Kostadinova, S.; Zheleva, E.

1995-01-01

The forest fallowing of coal-mine spoils helps re-establish the processes of natural, self-sustaining, soil formation. Environmental monitoring in Bulgaria demonstrates that forestation can moderate soil pH (from ph> 3.0 to pH 1.3 g/cm 3 in the 0-5 cm layer) in the case of coal briquette spoils at Pernik, near Sofia. Ground losses from forested, 16-17 degree slope, coal briquette-spoils at Pernik are a quarter of those from an entirely unvegetated section of the same embankment (48.5 vs 12. 1 mm in the period 1988-1994) despite the absence of ground cover beneath the trees. On lignite spoil banks, at Maritsa-Iztok, central Bulgaria, forestation increases the organic content of the soil to greater depths than revegetation with grass, and to a greater degree than conventional agricultural cultivation. On Pinus nigra forested crest sites at Pernik, and in Robinia pseudacacia forested groves on the lignite minespoil banks at Maritsa-Iztok, slopes showed ground advance rather than ground retreat. Slopes protected by mechanical means alone did not allow soil growth and, where the structure broke down, they suffered as much erosion as untreated sites. In sum, the forest fallowing of surface coal-mine disturbed land accelerates organic matter accumulation in the soil, helps improve soil structure, reduces erosion, and may transform soil loss into soil gain, even on steeply sloping sites. 17 refs., 3 figs., 1 tab

Reduction disintegration mechanism of cold briquettes from blast furnace dust and sludge

Directory of Open Access Journals (Sweden)

Leandro Rocha Lemos

2015-07-01

Full Text Available It is important to understand the reduction disintegration mechanism in ferriferous burden that is used in blast furnaces. The behavior of this burden in the granular zone of this metallurgical reactor is important for smooth operation. The objective of this work was to prepare cold self-reducing briquettes using blast furnace dust and sludge and binders and compare the reduction disintegration index (RDI of these agglomerates with conventional ferriferous burdens such as pellets, sinter and iron ore. In the present work, 25 different mixtures were prepared to produce briquettes in two geometries: pillow and cylindrical. The RDI value was determined for the briquettes that passed the tumbling test.

Survey report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Dispatch of engineers; 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (senmonka haken)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this survey is to improve the coal utilization technology and to contribute to the environmental protection. Through long-term dispatch of experts for the coal utilization technology, coal utilization facilities are surveyed at the sites, advises for coal utilization technology and environmental protection technology are given, and useful information for the cooperation with the partner country are exchanged. In this fiscal year, experts were dispatched to Thailand in addition to China, to conduct cooperative surveys, technical exchanges and seminars with both countries. Experts for desulfurization technology, circulating fluidized bed boilers, effective coal ash utilization technology, and coal preparation technology were dispatched to various places in China. Among various model projects conducted in China, examples of model projects for simplified desulfurizer introduction, circulating fluidized bed boiler introduction, and briquette production facility introduction were presented at seminars held at two cities in China. Experts for briquette production technology and circulating fluidized bed boiler technology were dispatched to Thailand, to conduct cooperative surveys and technical exchanges. 22 figs., 9 tabs.

Use of coffee (Coffea arabica pulp for the production of briquettes and pellets for heat generation

Directory of Open Access Journals (Sweden)

Robert Cubero-Abarca

2014-10-01

Full Text Available Coffee bean (Coffea arabica processing generates high amount of residues that are sources of environmental pollution. Therefore, an appropriate solution is needed. The objective of this study was to determine the potential of coffee pulp to produce briquettes and pellets. The study included pulp drying (using air, solar and hot air methods; the production of briquettes and pellets; the evaluation of their energy, physical and mechanical properties; and the evaluation of pellet quality using X-ray densitometry. The results showed that the pulp presented an initial moisture content of 90%, resulting in drying times of 699, 308 and 55 hours for air, solar and hot air drying, respectively, and the calorific values of the pellets and briquettes were 12,501 kJ kg-1 and 11,591 kJ kg-1, respectively. The ash content was 8.68% for the briquettes and 6.74% for the pellets. The density of the briquettes was 1,110 kg m-3, compared with 1,300 kg m-3 for the pellets. The apparent densities were 1,000 kg m-3 and 600 kg m-3 for the briquettes and pellets, respectively, and the water absorptions by the briquettes were 7.90% and 8.10% by the pellets. The maximum horizontal compression effort was 26.86 kg cm-2, measured in the pellets, compared with 4.52 kg cm-2 in the briquettes. The maximum horizontal load was 93.24 kg, measured in the briquettes, compared with 33.50 kg in the pellets. The value of the pellet durability test was 75.54%. X-ray densitometry showed that the pellet was uniform and a few cracks were observed on the pellet surface.

Brown coal gasification made easy

International Nuclear Information System (INIS)

Hamilton, Chris

2006-01-01

Few Victorians will be aware that gas derived from coal was first used in 1849 to provide lighting in a baker's shop in Swanston Street, long before electric lighting came to the State. The first commercial 'gas works' came on stream in 1856 and Melbourne then had street lighting run on gas. By 1892 there were 50 such gas works across the State. Virtually all were fed with black coal imported from New South Wales. Brown coal was first discovered west of Melbourne in 1857, and the Latrobe Valley deposits were identified in the early 1870s. Unfortunately, such wet brown coal did not suit the gas works. Various attempts to commercialise Victorian brown coal met with mixed success as it struggled to compete with imported New South Wales black coal. In June 1924 Yallourn A transmitted the first electric power to Melbourne, and thus began the Latrobe Valley's long association with generating electric power from brown coal. Around 1950, the Metropolitan Gas Company applied for financial assistance to build a towns gas plant using imported German gasification technology which had been originally designed for a brown coal briquette feed. The State Government promptly acquired the company and formed the Gas and Fuel Corporation. The Morwell Gasification Plant was opened on 9 December 1956 and began supplying Melbourne with medium heating value towns gas

Binderless briquetting of some selected South African prime coking, blend coking and weathered bituminous coals and the effect of coal properties on binderless briquetting

Energy Technology Data Exchange (ETDEWEB)

Mangena, S.J. [Division of Mining Technology, CSIR, PO Box 395, Pretoria, 0001 (South Africa); du Cann, V.M. [Coal and Mineral Technologies (Pty) Ltd, SABS, PO Box 73656, Lynnwood Ridge, Pretoria, 0040 (South Africa)

2007-07-02

The binderless briquetting of some selected South African prime coking and blend coking coals, as well as the effects of weathering on the binderless briquetting of some inertinite-rich bituminous coals, were investigated in the laboratory. Selected properties of these coals were determined and the coals were briquetted at various moisture contents and pressures. Based on the results obtained in this study, binderless briquetting was found to be most successful in the cases of the fresh, vitrinite-rich coking and blend coking coals and satisfactory in the fresh inertinite-rich Witbank coals. However, the bonding process seemed to be adversely affected by weathering. The negative impact on bonding could be ameliorated to some extent by the presence of a significant kaolinite content when the percentage ash reports in the order of more than 15% (air-dry basis). It should, however, be noted that kaolinite may reduce the water resistance of the briquettes. (author)

Modification of commercial briquetting machine to produce 35mm diameter briquettes suitable for gasification and combustion

Energy Technology Data Exchange (ETDEWEB)

Singh, R.N.; Bhoi, P.R.; Patel, S.R. [Thermo chemical Conversion Division, Sardar Patel Renewable Energy Research Institute (SPRERI), Vallabh Vidyanagar, 388 120 Gujarat (India)

2007-03-15

This paper describes an experience on producing 35mm dia briquettes with a modified commercial briquetting machine and the results of studies on the combustion and gasification behavior of briquettes. Study reveals that at 12% (w.b.) moisture content of groundnut shell powder (1180-150{mu}m), good quality briquettes can be made, but it reduces the production rate and increases the power requirement. Combustion as well as gasification studies revealed that biomass briquettes of 35mm diameter do not crumble or disintegrate during the conversion process, therefore these are suitable as feedstock for gasifiers. (author)

Ramie (Boehmeria nivea) decortication waste bio-briquette business model canvas with design thinking approach

Science.gov (United States)

Pahlavi, Ghifari Rezka; Purnomo, Dwi; Bunyamin, Anas; Wulandari, Asri Peni

2017-03-01

Ramie (Boehmeria nivea) is a plant that can produce fibers from its stem but in the production process, it still produces waste containing high lignin and cellulose. The high content of these substances can be used as bio-briquette raw material because they can produce carbon and can offer a business opportunity to establish bio-briquette industry. The purpose of this study is to obtain a ramie decortification waste bio-briquette business model because until now there is no bio-briquette has been made from ramie decortication waste as its raw material. This research uses descriptive analysis method with a design thinking approach. The result of this research shows that the business model canvas is designed based on consumer's experience when interacting with the product via customer journey tool in order to get the business model in accordance with customer expectations.

Compression Characteristics and Energy Requirement of Briquettes Made from a Mixture of Corn Stover and Peanut Shells

Directory of Open Access Journals (Sweden)

Chunxiao Gong

2015-07-01

Full Text Available Corn stover and peanut shells are both abundantly available biomass feedstocks in China. To determine the compression characteristics and energy requirement of briquettes, mixtures of the corn stover and peanut shells were compressed under three different pressures (30, 60, and 90 MPa with three moisture contents (9%, 14%, and 19%, wet basis and five corn stover-peanut shell mixtures (0%-100%, 25%-75%, 50%-50%, 75%-25%, and 100%-0% by mass. The results showed that applied pressure, moisture content, and the corn stover-peanut shell mixture all significantly affected briquette density and specific energy consumption. The density of the briquette ranged from 646 to 1052 kg/m3 and the specific energy consumption varied from 6.6 to 25.1 MJ/t. A moisture content of 9% was found to be better for the compression of the corn stover and peanut shells mixture. Adding peanut shells to the corn stover improved briquette density and reduced the specific energy consumption. Linear models were developed to describe the briquette density and the specific energy consumption. The briquette durability ranged from 57% to 94% and durable briquettes can be obtained when corn stover and peanut shells are compressed with the mixing ratio of 1:1 (50%-50% at moisture content of 9%.

Pengaruh Tekanan Pembriketan dan Persentase Briket Campuran Gambut dan Arang Pelepah Daun Kelapa Sawit terhadap Karakteristik Pembakaran Briket

Directory of Open Access Journals (Sweden)

Andy Nugraha

2017-05-01

Full Text Available Briquettes mixture of peat and charcoal leaf midrib palm oil is one of the alternative energy for replacing fossil fuel energy. It is environmentally friendly and abundant in Indonesia, mainly in South Kalimantan. In this study, the percentage of briquettes mixture of peat and charcoal leaf midrib of palm oil were 50%:50%, 60%:40%, 70%:30%, 80%:20% and 90%:10%, respectively. In addition, 1 gram of starch was added as an adhesive for every variation of briquettes mixture. In briquetting process, the pressures were 10 kg/cm2, 20 kg/cm2 and 30 kg/cm2. The combustion characteristics of  briquettes was tested, then it was compared by subbituminous coal briquettes. The results show, ignition delay of briquettes decrease by increasing additional percentage of peat, however extend the burning time of briquettes, consequently the burning rate decrease and the briquettes temperature becomes low. Briquetting pressure affects the combustion characteristics of briquettes. Ignition delay of briquettes decrease by the pressure. On the other hand, extend the burning time of briquettes and decrease the burning rate, however combustion temperatures of briquettes increases. The results also show a comparison of mixture briquettes peat and charcoal palm leaf midrib with subbituminus coal briquettes. The subbituminous coal briquettes produces higher combustion temperature, the longer combustion process and the lowest  combustion rate.

Implications of Charcoal Briquette Produced by Local Communities on Livelihoods and Environment in Nairobi- Kenya

Directory of Open Access Journals (Sweden)

M. Njenga

2013-02-01

Full Text Available The residents of Nairobi, Kenya, use 700 tonnes of charcoal per day, producing about88 tonnes of charcoal dust that is found in most of the charcoal retailing stalls that is disposed of inwater drainage systems or in black garbage heaps. The high costs of cooking fuel results in poorhouseholds using unhealthy materials such as plastic waste. Further, poor households are opting tocook foods that take a short time to prepare irrespective of their nutritional value. This articlepresents experiences with community self-help groups producing charcoal fuel briquettes fromcharcoal dust in poorer nieghbourhoods of Nairobi for home use and sale. Households thatproduced charcoal fuel briquettes for own use and those that bought them saved 70% and 30% ofmoney spent on cooking energy respectively. The charcoal fuel briquettes have been found to beenvironmentally beneficial since they produce less smoke and increase total cooking energy bymore than 15%, thereby saving an equivalent volume of trees that would be cut down for charcoal.Charcoal briquette production is a viable opportunity for good quality and affordable cooking fuel.Bioenergy and waste management initiatives should promote recovery of organic by-products forcharcoal briquette production.

An experimental study of the combustion characteristics of groundnut shell and waste paper admixture briquettes

Directory of Open Access Journals (Sweden)

O. A. Oyelaran

2015-12-01

Full Text Available The study was undertaken to assess the heat released of briquettes produced from waste paper and groundnut shell admixture in five mixing ratios (90:10; 80:20; 70:30; 60:40; and 50:50. The briquettes were prepared on an existing motorized briquetting machine. The suitability of briquetted fuel as domestic fuel was studied in terms of flame propagation, afterglow, calorific value, and utilized heat, after sun drying the prepared briquettes for nineteen (19 days. The results of propagation rate and afterglow obtained for all the six compositions are satisfactory they range between 0.13 to 0.14 and 365 to 380 respectively. These energy values obtained for the whole samples are sufficient enough to produce heat required for household cooking and small scale industrial cottage applications. Finally it was observed that composition variation affects the properties of the briquettes.

Carbon-based catalytic briquettes for the reduction of NO: Effect of H{sub 2}SO{sub 4} and HNO{sub 3} carbon support treatment

Energy Technology Data Exchange (ETDEWEB)

A. Boyano; M.E. Galvez; R. Moliner; M.J. Lazaro [Instituto de Carboquimica CSIC, Zaragoza (Spain)

2008-08-15

The influence of treating carbon with sulphuric and nitric acids on the activity of a carbon-based briquette catalyst for NO reduction with NH{sub 3} was examined in a fixed-bed reactor at low temperature (150{sup o}C). The briquette catalysts were prepared from a low-rank coal and a commercial tar pitch. The active phase was impregnated from a suspension of ashes of petroleum coke by means of an equilibrium adsorption method. The catalytic behaviour of NO reduction over acid treated briquettes was found to vary with the surface characteristics of the carbon support. This suggests that the number of oxygen-containing sites as well as vanadium load and dispersion affect the reaction activity. In the presence of oxygen, the SCR activity is enhanced with a nitric acid treatment, activity is promoted by the presence of acidic surface groups such as carboxyl and lactone, which can help not only to create a reservoir of reactants on the catalysts surface but also to improve the dispersion or even increase the amount of vanadium loading. Therefore, the results of this study suggest that the formation of acidic sites on the surface is an important step for NO reduction with NH{sub 3} over carbon-based catalysts. Additional techniques such as XPS and TPD to characterize the oxygen surface and those such as N{sub 2} adsorption to characterize the textural properties were also used in this study. 46 refs., 6 figs., 5 tabs.

Evaluating the bio-energy potential of groundnut shell and sugarcane bagasse waste composite

Directory of Open Access Journals (Sweden)

Olatunde Ajani Oyelaran

2015-12-01

Full Text Available An assessment has been carried out on bio-coal briquettes from coal with sugarcane bagasse and coal with groundnut shell. Proximate analyses and elemental compositions of the coal and biomasses were determined. Different samples of briquettes were produced by blending varying composition of the coal with the biomasses in the ratio of 100:0; 90:10, 80:20, 70:30, 60:40, 50:50, 40:60 and 0: 100, using calcium carbonate as a desulfurizing agent and cassava starch as a binder. A manual hydraulically operated briquetting machine was used with the pressure kept at 5MPa. The results of the properties evaluated shows that biomass increases the burning efficiency of briquettes with increase in the biomass material, increasing combustion rate, faster ignition, producing lesser ash and fewer pollutants. Results obtained shows that the calorific value of briquettes produced from coal-groundnut shells and coal-sugarcane bagasse ranges from 16.94 - 20.81 and 17.31 – 21.03 MJ/kg respectively. The ignition time ranges from 6.9 – 12.5 minutes for coal-groundnut shells briquettes while that of coal-sugarcane bagasse ranges from 6.5 – 11.1 minutes. The bio-coal blends with sugarcane bagasse were better than that of groundnut shells. However, both sugarcane bagasse and groundnut shells produce bio-coal briquettes that are very efficient, providing sufficient heat as at the time necessary, generating less smoke and gases (e.g sulphur that are harmful to environment, and generating less ash, as these have adverse effect during cooking.

INVESTIGATION ON THE QUALITY OF BRIQUETTES MADE FROM RARELY USED WOOD SPECIES, AGRO-WASTES AND FOREST BIOMASS

Directory of Open Access Journals (Sweden)

Camelia COŞEREANU

2015-03-01

Full Text Available Characteristics of briquettes made from various biomass resources (staghorn sumac wood, vineyard and apple tree pruning biomass, pine cones, corn stalk and corn cobs were investigated in the present paper. The moisture content of raw materials was first determined, before compacting them in a hydraulic briquetting machine. Briquettes with diameter of 40mm and various lengths were obtained. Five replicates of each briquette type were selected for the determination of density, compression strength and calorific value. The results were compared to those of beech and pine briquettes obtained under similar conditions. Based on the experimental results, mathematical correlations between density and compression strength and density and calorific value were investigated.

Coal characteristics from 'Priskupshtina' deposit and technological parameters for briquetting (Macedonia)

International Nuclear Information System (INIS)

Damjanovski, Dragan

1998-01-01

The use of small class coal as well as the lack of formed fuel needed for the industry and for the consumer goods has been a long lasting problem, and a challenge for the researchers of the Republic of Macedonia. For that purpose, all-inclusive analysis of the quality of the coals in Macedonia, their reserves and technical characteristics, as well as analysis of the petrographic structure were made. Classification of the deposits and the research for the possibility of making briquettes was done, too. Laboratory investigations in the coal deposit 'Priskupshtina' were carried out. The analysis of the coal briquetting show that the expected results in coordination with the required standards were not obtained. Spatially the results from the coal calorific value, its hardness and atmospheric resistance. Standard methods were used for the researches without connective means and the achieved results were mutually correlated. Technical-economic verification is necessary in the further process. (Author)

Effects of polymerization and briquetting parameters on the tensile strength of briquettes formed from coal coke and aniline-formaldehyde resin

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A.; Simsek, T. [Selcuk University, Konya (Turkey)

2006-10-15

In this work, the utilization of aniline (C{sub 6}H{sub 7}N) formaldehyde (HCHO) resins as a binding agent of coke briquetting was investigated. Aniline (AN) formaldehyde (F) resins are a family of thermoplastics synthesized by condensing AN and F in an acid solution exhibiting high dielectric strength. The tensile strength sharply increases as the ratio of F to AN from 0.5 to 1.6, and it reaches the highest values between 1.6 and 2.2 F/AN ratio; it then slightly decreases. The highest tensile strength of F-AN resin-coke briquette (23.66 MN/m{sup 2}) was obtained from the run with 1.5 of F/AN ratio by using (NH4){sub 2}S{sub 2}O{sub 8} catalyst at 310 K briquetting temperature. The tensile strength of F-AN resin-coke briquette slightly decreased with increasing the catalyst percent to 0.10%, and then it sharply decreased to zero with increasing the catalyst percent to 0.2%. The effect of pH on the tensile strength is irregular. As the pH of the mixture increases from 9.0 to 9.2, the tensile strength shows a sharp increase, and the curve reaches a plateau value between pH 9.3 and 9.9; then the tensile strength shows a slight increase after pH = 9.9.

Fine coke production from brown coal (Report on ECSC contract 6220-72/1/102)

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

The possibility of producing a dry brown coal suitable for the production of fine coke and the development of a suitable carbonization process were studied. To prepare the coal it should be screened at 1 mm with the oversize going to fine coke production and the undersize going to briquette production. To increase fine coke production it is necessary to screen the raw smalls less than 2 mm and to pelletize, dry and carbonize them with the coarser constituents. The planning and construction of a hearth oven furnace plant was begun and this is now in operation. A fluidized bed can be used to preheat the coal to improve the oven performance. (In German)

Investigation of Mechanical Properties of Briquette Product of ...

African Journals Online (AJOL)

ADOWIE PERE

with the increased in the consumption of fuel wood etc. ... depletion is one of the most crucial issues for many countries. ... emissions since nearly zero net gain CO2 can be achieved when ..... Using cotton plant residue to produce briquettes.

Potential of Tropical Fruit Waste Biomass for Production of Bio-Briquette Fuel: Using Indonesia as an Example

Directory of Open Access Journals (Sweden)

Anna Brunerová

2017-12-01

Full Text Available Within developing countries, there is an appeal to use waste biomass for energy generation in the form of bio-briquettes. This study investigated the potential use of bio-briquettes that are produced from the waste biomass of the following tropical fruits: durian (Durio zibethinus, coconut (Cocos nucifera, coffee (Coffea arabica, cacao (Theobroma cacao, banana (Musa acuminata and rambutan (Nephelium lappaceum. All fruit waste biomass samples exhibited an extremely high level of initial moisture content (78.22% in average. Fruit samples with the highest proportion of fruit waste biomass (of total unprocessed fruit mass were represented by cacao (83.82%, durian (62.56% and coconut (56.83%. Highest energy potentials (calorific value of fruit waste biomass were observed in case of coconut (18.22 MJ∙kg−1, banana (17.79 MJ∙kg−1 and durian (17.60 MJ∙kg−1 fruit samples, whereas fruit waste biomass with the lowest level of ash content originated from the rambutan (3.67%, coconut (4.52%, and durian (5.05% fruit samples. When investigating the energy demands to produce bio-briquettes from such feedstock materials, the best results (lowest amount of required deformation energy in combination with highest level of bio-briquette bulk density were achieved by the rambutan, durian and banana fruit waste biomass samples. Finally, all investigated bio-briquette samples presented satisfactory levels of bulk density (>1050 kg∙m−3. In conclusion, our results indicated the practicability and viability of such bio-briquette fuel production, as well as supporting the fact that bio-briquettes from tropical fruit waste biomass can offer a potentially attractive energy source with many benefits, especially in rural areas.

Effect of torrefaction pre-treatment on physical and combustion characteristics of biomass composite briquette from rice husk and banana residue

Directory of Open Access Journals (Sweden)

Amira Atan Nor

2018-01-01

Full Text Available Biomass is an alternative renewable energy sources that can generates energy almost same as fossil fuel. The depletion sources of fossil fuel had increase the potential use of biomass energy. In Malaysia, rice husk and banana residues are abundantly left and not treated with proper disposal method which later may contribute to environment and health problems. Thus the development of biomass composite briquette made from rice husk and banana residue is one of the potential ways to reduce the problems and hence may contribute the better way to treat the waste by recycling the waste into a form of biomass product. The biomass briquettes are used for thermal applications because it can produce a complete combustion as it has a consistent quality and high burning efficiency. However, the quality of the biomass briquette can be added by application of torrefaction pre-treatment method. Torrefaction is a thermal method that can produce more high quality of the briquette with high calorific value, high fixed carbon content, low volatile matter, and low ash content. This study was conducted to assess the physical and combustion characteristic of the biomass briquette from rice husk and banana residue which was produced through torrefaction process. The biomass briquette, were densified by using hot press machine with temperature of 180°C for about 30 minutes. The briquette produce are 150 μm in particle size with varies in mixing ratio of rice husk to banana residue which are 100:0, 80:20 and 60:40. After the briquetting process, the biomass fuel briquettes have been undergoes parameter testing and the data have been analysed. Result showed the best biomass briquette is developed from torrefied rice husk and banana residue mixed at ratio of 60:40. Moreover, SEM image reveal that torrefaction pre-treatment has shrinkage the fibres size which confirming the thermal stability of the briquette.

The Effect of Moisture of the Raw Material on the Properties Briquettes for Energy Use

Directory of Open Access Journals (Sweden)

Milan Brožek

2016-01-01

Full Text Available At logging and at the subsequent wood and wood semi-products treatment the fine grained loose waste is arising, e.g. wood dust, saw dust, shavings, chips, bark etc. One of possibilities of its meaningful utilization is the briquetting technology, which product are briquettes determined for energetic utilization (combustion. This report contains the results of tests carried out with the aim to assess the influence of moisture on the briquettes final properties. For the tests the platan tree chips of four moisture levels, namely 5.7 %, 7.7 %, 15.7 % and 23.9 % were used. The basic physical-mechanical properties were the evaluation criteria. Following properties were determined: ash amount, gross calorific value, total moisture content, density, rupture force, length, diameter, weight and mechanical durability. From the results of carried out tests it follows that the best properties were reached at briquettes made from chips of moisture 7.7 %. At higher or lower moisture the briquettes properties were sharply failing (namely rupture force and density.

Performance Evaluation of the Effect of waste paper on Groundnut Shell Briquette

Directory of Open Access Journals (Sweden)

Olatunde A Oyelaran

2015-07-01

Full Text Available Current energy shortage and environmental issues resulting from the use of fossil fuels have lead to exploitation of renewable energy resources that includes municipal waste and agricultural residues. These residues are available, indigenous and are environmental friendly but some can not be used directly in combustion process due high moisture content and low volumetric energy unless by briquetting. The study was undertaken to assess the combustion characteristic of binderless briquettes produced from waste paper and groundnut shell. Combustion characteristics investigated were ignition time, burning time, calorific values, burning rate, specific fuel consumption, fuel efficiency and water boiling time. The calorific values of the briquettes ranged from 19.51 - 19.92 MJ/kg, while the thermal efficiency ranges between 13.75 – 21.64%, other results shows that the average burning rate between 0.511 and 1.133 kg/hr and the specific fuel consumption ranges between 0.087 and 0.131 J/g. The recorded boiling time values were between 17.5 and 30.0 minutes for cold start and 15.0 and 20.0 minutes for hot start. The results shows that waste paper and groundnut shell up to 25% in composition composite briquettes were found to have good combustion characteristics which qualify them as alternative to firewood for domestic and industrial energy. However, production of briquettes from waste paper and groundnut shell at mixing ratio of 85:15 was found to comparatively better from all experiment conducted.

Use of various types of carbon-containing raw materials to produce thermal energy

Directory of Open Access Journals (Sweden)

В. Б. Кусков

2016-08-01

Full Text Available Many types of carbon-containing organic compounds and all possible carbon-containing products or wastes in low demand can be used to produce thermal energy. A technology has been developed for producing highly flammable briquettes on the basis of bituminous coal. These briquettes have a special incendiary layer. It is easily ignites from low energy heat sources (e.g. matches, and then flame spreads to the rest of briquette. Use of coal slacks and paper wastes as carbon-containing components playing the role of binders provides an opportunity to get a fuel briquette easy in terms of production and plain in composition while at the same time dispose of coal and paper wastes. Such briquettes may also have a special incendiary layer. Technology for fuel briquettes production from wood and slate wastes employed no binding agents, as wood products acted as binders. Thus technologies have been developed to produce fuel briquettes from various carbon-containing materials in low demand. The briquettes are intended for household boilers, fireplaces, different ovens in order to cook food, heat residential and utility premises, cabins, etc.

The Bricoke process for producing metallurgical coke in conventional ovens from blends containing a high percentage of non-coking coal

Energy Technology Data Exchange (ETDEWEB)

Vidal, R; Munnix, K; Dellieu, J

1980-06-01

The article discusses the following aspects:- description of the BRICOKE process; trials in pilot plant, showing the influence of the different parameters on the coke quality and delimiting the range of the suitable non-coking coals; industrial scale trials of long term with 33% of non-coking coal briquettes in the charge; influence on the coking process as well as on the blast furnace working and increase of the output of usual coke-oven by the BRICOKE process. (11 refs.)

The influence of lisping material in pelletizing and agglomeration of fine coal pieces in laboratory conditions

International Nuclear Information System (INIS)

Vrencovski, Angele; Andreevski, Borche

1998-01-01

The work presents a part of laboratory results realized in academy of Firebug, carried on pelletizing and agglomeration of waste material, fine coal from thermal power station, using different lisping materials. Specially the influence of these materials in getting solid fuel, small briquette, formed by rolling press is analyzed. Special interest is attended to their characteristics: hardness and resistance. (Author)

Material and operating variables affecting the physical quality of biomass briquettes

Energy Technology Data Exchange (ETDEWEB)

Song, Y.; Xin, M. [Shenyang Agricultural Univ., Shenyang (China). College of Engineering; Tumuluru, J.S.; Iroba, K.L.; Tabil, L.G.; Meda, V. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Agricultural and Bioresource Engineering

2010-07-01

Although biomass is an environmentally sound substitute for fossil fuels, its low bulk density makes it very difficult and costly to transport and handle. This challenge can be addressed by densifying the biomass to a high density product like briquettes. Briquetting is influenced by several material properties such as moisture content, particle size distribution, and some operating variables such as temperature and densification pressure. This paper reported on a study in which briquettes were produced with barley straw, canola straw, oat straw, and wheat straw. The chopped samples were densified using a laboratory hydraulic press briquetting machine at pressure levels of 7.5, 10, and 12.5 MPa and at temperatures of 90, 110 and 130 degrees C. Three moisture content levels and 3 levels of particle size were used. Ten briquettes were manufactured for each treatment combination. The dimensions of all the samples were measured after compression. The samples were then stored in sealed plastic bags in a controlled environment. Durability, dimensional stability, and moisture content tests were conducted after 2 weeks of storage. The study showed that moisture content plays a key role in briquetting.

Feasibility of Biomass Briquette Production from Municipal Waste Streams by Integrating the Informal Sector in the Philippines

Directory of Open Access Journals (Sweden)

Aries Roda D. Romallosa

2017-02-01

Full Text Available A technical and socio-economic feasibility study of biomass briquette production was performed in Iloilo City, Philippines, by integrating a registered group of the informal sector. The study has shown that the simulated production of biomass briquettes obtained from the municipal waste stream could lead to a feasible on-site fuel production line after determining its usability, quality and applicability to the would-be users. The technology utilized for briquetting is not complicated when operated due to its simple, yet sturdy design with suggestive results in terms of production rate, bulk density and heating value of the briquettes produced. Quality briquettes were created from mixtures of waste paper, sawdust and carbonized rice husk, making these material flows a renewable source of cost-effective fuels. An informal sector that would venture into briquette production can be considered profitable for small business enterprising, as demonstrated in the study. The informal sector from other parts of the world, having similar conditionality with that of the Uswag Calajunan Livelihood Association, Inc. (UCLA, could play a significant role in the recovery of these reusable waste materials from the waste stream and can add value to them as alternative fuels and raw materials (AFR for household energy supply using appropriate technologies.

Benazir Bhutto. Pakistani nimel vaenlasega voodisse / Triin Oppi

Index Scriptorium Estoniae

Oppi, Triin

2007-01-01

Pakistani endise peaministri Benazir Bhutto elukäigust, elust eksiilis, karjäärist, korruptsioonisüüdistustest, vastasseisust president Pervez Musharrafiga, plaanist naasta Pakistani 18. oktoobril. Vt. samas: Kahtlased võimumängud

Emission factors of polycyclic and nitro-polycyclic aromatic hydrocarbons from residential combustion of coal and crop residue pellets.

Science.gov (United States)

Yang, Xiaoyang; Liu, Shijie; Xu, Yisheng; Liu, Yu; Chen, Lijiang; Tang, Ning; Hayakawa, Kazuichi

2017-12-01

Polycyclic aromatic hydrocarbons (PAHs) and nitro-polycyclic aromatic hydrocarbons (NPAHs) are toxic pollutants mainly produced during fossil fuel combustion. Domestic coal stoves, which emit large amounts of PAHs and NPAHs, are widely used in the Chinese countryside. In this study, emission factors (Efs) for 13 PAH species and 21 NPAH species for four raw coal (three bituminous and one anthracite), one honeycomb briquette, and one crop residue pellet (peanut hulls) samples burned in a typical Chinese rural cooking stove were determined experimentally. The PAH and NPAH Efs for the six fuels were 3.15-49 mg/kg and 0.32-100 μg/kg, respectively. Peanut hulls had very high Efs for both PAHs and NPAHs, and honeycomb briquettes had the lowest Efs. 2-Nitropyrene and 2-nitrofluoranthene, which are NPAHs typically found in secondary organic aerosol, were detected in the emissions from some fuels, suggesting that chemical reactions may have occurred in the dilution tunnel between the flue gas leaving the stove and entering the sampler. The 1-nitropyrene to pyrene diagnostic ratios for coal and peanut hulls were 0.0001 ± 0.0001 and 0.0005, respectively. These were in the same order of magnitude as reference ratios for emissions during coal combustion. The 6-nitrobenzo[a]pyrene to benzo[a]pyrene ratios for the fuels were determined, and the ratios for coal and peanut hulls were 0.0010 ± 0.0001 and 0.0014, respectively. The calculated potential toxic risks indicated that peanut hull emissions were very toxic, especially in terms of NPAHs, compared with emissions from the other fuels. Copyright © 2017 Elsevier Ltd. All rights reserved.

Briquetting of coal fines and sawdust. Part 1: binder and briquetting-parameters evaluations

Energy Technology Data Exchange (ETDEWEB)

D. Taulbee; D.P. Patil; Rick Q. Honaker; B.K. Parekh [University of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

2009-01-15

Various technical and economic aspects relating to the briquetting of fine coal with sawdust have been evaluated with the results for two segments of that study presented here: binder and briquetting-parameter evaluations. Approximately 50 potential binder formulations were subjected to a series of screening evaluations to identify three formulations that were the most cost effective for briquetting fine coal with sawdust. Two of the binders, guar gum and wheat starch, were selected as most suitable for the pulverized coal market while the third formulation, lignosulfonate/lime, was targeted for the stoker market. Following binder selection, a number of briquetting parameters including binder and sawdust concentration, sawdust type, briquetting pressure and dwell time, coal and sawdust particle size, clay content, moisture content, and cure temperature and cure time were evaluated. Briquetting pressure and dwell time have the least impact while binder and sawdust concentrations, sawdust type, and curing conditions exerted the greatest influence on briquette quality. 7 refs.

Production of Solid Fuel Briquettes from Agricultural and Wood ...

African Journals Online (AJOL)

Fibrous agricultural and wood waste materials have been compressed with suitable adhesive into solid fuel briquettes in a compressing machine, which was designed and constructed for this purpose. Nine samples of fibrous waste materials were prepared into different categories:- Category A (100% saw-dust, 100% ...

Effect of carbon black on thermal properties of charcoal and salacca leafstalk briquettes

Science.gov (United States)

Thassana, Chewa; Nuleg, Witoon

2017-08-01

In this work, the effect of a carbon black (CB) on the thermal properties of briquettes produced from the charcoal and the salacca leafstalk with and without CB have been investigated. Four thermal properties of a briquettes compose of the burning time, the calorific value, the percentage moisture (PMC) and an percentage ash content (PAC) were analyzed using standard laboratory methods. Our results were indicated that the sallacca leafstalk mix a carbon black is the long burning times, high heating but a few ash content. Results shown that the burning time and the calorific value of a charcoal, a charcoal with CB, the salacca leafstalk and the salacca leafstalk with carbon black particles is about 58, 63, 76, 81 minutes, and 10.33, 12.96, 13.12, 14.63 MJ/kg, respectively. In addition, the PMC and PAC were in range of 11.6 - 8.14% and 9.33 - 5.42%. So, we can conclude that a cabon black affect on the thermal properties of a briquettes and salacca leaftstalk mixed CB has been most suited for briquetting.

Briquettes of plant remains from the greenhouses of Almeria (Spain)

Energy Technology Data Exchange (ETDEWEB)

Callejon-Ferre, A. J.; Lopez-Martinez, J. A.

2009-07-01

Since ancient times, plant biomass has been used as a primary fuel, and today, with the impending depletion of fossil fuels, these vegetal sources constitute a cleaner alternative and furthermore have a multitude of uses. The aim of the present study is to design a method of recycling and reuse of plant wastes from intensive agriculture under plastic, by manufacturing briquettes in an environmentally friendly manner. In Almeria (SE Spain), agriculture generates 769,500 t year{sup -}1 of plant remains from greenhouse-grown horticultural crops, a resource currently used for composting and for producing electricity.With the machinery and procedures of the present study, another potential use has been developed by detoxifying and eliminating the plastic wastes of the original biomass for the fabrication of briquettes for fireplaces. The results were slightly inferior to the commercial briquette from other non-horticultural plant materials (no forestry material), specifically 2512 kJ kg{sup -}1, in the least favourable case. On the contrary, the heating value with respect to the two charcoals was significantly lower, with a difference of 12,142 kJ kg{sup -}1. In conclusion; a procedure, applicable in ecological cultivation without agrochemicals or plastic cords, has been developed and tested to reuse and transform plant materials from intensive cultivation into a stable non-toxic product similar to composite logs, applicable in commercial settings or in residential fireplaces. (Author) 48 refs.

Low-grade coals: a review of some prospective upgrading technologies

Energy Technology Data Exchange (ETDEWEB)

Hassan Katalambula; Rajender Gupta [University of Alberta, Edmonton, AB (Canada). Department of Chemical and Materials Engineering

2009-07-15

There is a growing need of using low-grade coals because of higher quest for power generation. In the present carbon-constrained environment, there is a need of upgrading these coals in terms of moisture, ash, and/or other trace elements. The current paper reviews technologies used mainly categorized as drying for reducing moisture and cleaning the coal for reducing mineral content of coal and related harmful constituents, such as sulfur and mercury. The earliest upgrading of high-moisture lignite involved drying and manufacturing of briquettes. Drying technologies consist of both evaporative and non-evaporative (dewatering) types. The conventional coal cleaning used density separation in water medium. However, with water being a very important resource, conservation of water is pushing toward the development of dry cleaning of coal. There are also highly advanced coal-cleaning technologies that produce ultra-clean coals and produce coals with less than 0.1% of ash. The paper discusses some of the promising upgrading technologies aimed at improving these coals in terms of their moisture, ash, and other pollutant components. It also attempts to present the current status of the technologies in terms of development toward commercialization and highlights on problems encountered. It is obvious that still the upgrading goal has not been realized adequately. It can therefore be concluded that, because reserves for low-grade coals are quite plentiful, it is important to intensify efforts that will make these coals usable in an acceptable manner in terms of energy efficiency and environmental protection. 68 refs., 7 figs.

Heat Energy From Value-Added Sawdust Briquettes Of Albizia Zygia ...

African Journals Online (AJOL)

Choice-Academy

... physical properties between the sawdust briquettes and the solid wood of the same species were carried out. The results ... kerosene and cooking gas in Nigeria, draw attention to the .... between the physical properties of solid wood used for ...

Investigation of mechanical properties of briquette product of ...

African Journals Online (AJOL)

This research investigated the relaxed densities of biomass briquettes produced from combination of sawdust and charcoal. Cassava starch gel and orange waste were used as binder for briquetting. Five sizes; 0.2 mm, 0.4 mm, 0.6 mm, 0.8 mm and 1.0 mm and mixing ratios 50:50, 60:40, 70:30, 80:20 and 90:10 of biomass ...

EAF smelting trials of waste-carbon briquettes at Avesta Works of Outokumpu Stainless AB for recycling oily mill scale sludge from stainless steel production

Energy Technology Data Exchange (ETDEWEB)

Yang Qixing; Bjoerkman, Bo [Div. of Process Metallurgy, Lulea Univ. of Tech., Lulea (Sweden); Holmberg, Nils [Raw Materials Handling, Avesta Works, Outokumpu Stainless AB, Avesta (Sweden)

2009-06-15

The EAF steel plant of Avesta Works, Outokumpu Stainless AB, has been used to perform smelting reduction trials of briquettes consisting of oily mill scale sludge, carbon and other wastes. A total of 7 briquette smelting trials were performed. The heats were processed smoothly smelting 3 t of briquettes or 3.4 mass-% of metal charges. The quantities of FeSi powder and O{sub 2} gas injected and electric energy supplied were increased to smelt briquettes of 6 t. No impacts were found on the analyses of the crude stainless steel tapped from the EAF during the trials. The results of the briquette smelting have been evaluated by referring to the data from the reference heats and results from earlier laboratory tests. The recovery of Cr, Ni and Fe elements from the briquettes was nearly complete and was found to occur mainly through carbon reduction. The slag masses were not increased in three trials as compared with the reference heats. There were moderate increases in the slag masses in four trial heats. The increases were, nevertheless, lower by 52-69% than the slag masses generated by Si-reduction of the briquette oxides. Afterwards, by referring results from the present trials, waste-carbon briquettes amounting to 1-3 t were smelted very smoothly in many of the EAF heats at Avesta Works to recycle the oily mill scale sludge and other wastes from stainless steel production. (orig.)

Optimizaiton study of lime-upright-furnace briquette used as a substitution for coke with orthogonal experiments

Energy Technology Data Exchange (ETDEWEB)

Peng, H.; Zhou, J.; Deng, S.; Hao, X. [Central South University, Changsha (China)

2006-12-15

Test results were processed using the method of multi-factorial total probability formula evaluation. Based on range analysis and variance analysis, the optimal component of the compound binder was obtained, namely 4% magnesium-base curing agent, 1% biomass fiber, 1% activator, 0.12% calcium lignosulfonate. Key parameters of briquetting were determined, namely 20kN briquetting pressure, 17% briquetting water, 10% mixture ratio of bituminous coal. The size-composition of anthracite was: 58% less that 0.5 mm, 14% between 0.5 and 1.00 mm, 17% between 1.0 and 2.0 mm and 11% between 2.0 and 3.0 mm. The bonding mechanism of the compound binder was analyzed and the optimal parameter of briquetting determined. The results show that the lime-upright furnace briquette prepared according to the optimal scheme obtained in this experiment has an excellent cold strength, hot strength and heat stability which satisfies the requirements of the industrial production of lime-upright furnace briquets. 4 refs., 7 tabs.

Research and development to prepare and characterize robust coal/biomass mixtures for direct co-feeding into gasification systems

Energy Technology Data Exchange (ETDEWEB)

Felix, Larry [Inst. Of Gas Technology, Des Plaines, IL (United States); Farthing, William [Inst. Of Gas Technology, Des Plaines, IL (United States); Hoekman, S. Kent [Inst. Of Gas Technology, Des Plaines, IL (United States)

2014-12-31

This project was initiated on October 1, 2010 and utilizes equipment and research supported by the Department of Energy, National Energy Technology Laboratory, under Award Number DE- FE0005349. It is also based upon previous work supported by the Department of Energy, National Energy Technology Laboratory, under Award Numbers DOE-DE-FG36-01GOl1082, DE-FG36-02G012011 or DE-EE0000272. The overall goal of the work performed was to demonstrate and assess the economic viability of fast hydrothermal carbonization (HTC) for transforming lignocellulosic biomass into a densified, friable fuel to gasify like coal that can be easily blended with ground coal and coal fines and then be formed into robust, weather-resistant pellets and briquettes.

Pakistani juht sepitseb endale teist ametiaega / Heiki Suurkask

Index Scriptorium Estoniae

Suurkask, Heiki, 1972-

2007-01-01

Autori sõnul üritab Pakistani president Pervez Musharraf saavutada oma tagasivalimist lubadusega hakata tsiviilisikust presidendiks. Võimud on ähvardanud maapaost naasva endise Pakistani peaministri Benazir Bhutto vangi panna, juba on välja saadetud teine ekspeaminister Nawaz Sharif. Lisa: Kodusõja oht. Piirialad ähvardavad lahku lüüa

Effect of process variables on the calorific value and compressive strength of the briquettes made from high moisture Empty Fruit Bunches (EFB)

Science.gov (United States)

Helwani, Z.; Fatra, W.; Arifin, L.; Othman, M. R.; Syapsan

2018-04-01

In this study, the manual hydraulic press was designed to prepare the briquettes from selected biomass waste. Each biomass was sun-dried and milled into small particle sizes before mixing with crude glycerol that used as a biomass binder. The effects of applied pressure levels of 100, 110, 120 bars, the particle size of 60, 80 and 100 mesh and the binder composition on the density, compressive strength and calorific heating value of the prepared briquettes were investigated using response surface methodology (RSM). Results showed that the briquettes have an average inside diameter, average outside diameter, and height of 12, 38, and 25-30 mm, respectively. The density of the briquettes increased with increasing the applied pressure, was in the range of 623-923 kg/m3. The densest briquettes were obtained at 80 mesh of particle size, 53:47 binder composition ratio and 110 bars of pressurizing. The heating value of the briquette reached up to 28.99 MJ/kg obtained on the particle size of 80 mesh, 53:47 binder composition, and 110 bars and the best compressive strength of 6.991 kg/cm2 obtained at a particle size of 100 mesh, 60:40 binder composition, and 120 bars. Process conditions influence the calorific value significantly.

Contributions to the prompt neutron activation analysis of industrially used coals and zinc roasting products

International Nuclear Information System (INIS)

Dammermann, H.

1982-01-01

The construction of an irradiation plant for calibration measurement by means of prompt neutron activation analysis is described. A 5.84 μg and 16.3 μg Cf-252 source serve as neutron sources. Tests have shown an inner centred arrangement to offer the best solution for sources of this strength. The use of the PNAA method for determining sulphur, iron and chloride content in brown coal was tested and calibration curves drawn. The sulphur content of the coal briquettes tested was found to be 0.27% S, the iron content amounting to 0.21% Fe and chloride to 0.06%. These values correlate closely with values obtained from wet chemical industrial analysis. (WI)

PECUNIA EX MACHINA: PAKISTANI ENTREPRENEURS IN THE CITY OF BARCELONA

Directory of Open Access Journals (Sweden)

Hugo Valenzuela García

2010-12-01

Full Text Available The Pakistani migratory project is profoundly driven by economic objectives that are clearly apparent in their hard-working attitudes, their typically modest expenditure and consumption, the high rate of ethnic entrepreneurship and their remarkable commercial success. Nevertheless, the manifest economic inclination of the group involves a high social cost. This article analyses the economic and socio-cultural key issues that underlie the economic behavior of Pakistanis, as well as the social cost of the migratory enterprise. Furthermore, the paper describes the socio-cultural traits of the Pakistani community and, through a description of Pakistani settlement, it focuses on other important processes that concern the configuration of the city, such as gentrification, centrifugation and reproduction.

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

A cross-cultural comparison of British and Pakistani medical students' understanding of schizophrenia.

Science.gov (United States)

Furnham, Adrian; Raja, Nazia; Khan, Umar Ali

2008-06-30

This study aimed to compare British, British Pakistani and Native Pakistani (from Pakistan) medical students' beliefs about the manifestation, causes and cures of schizophrenia, prior to any psychiatric training. A total of 305 participants completed a questionnaire on general beliefs about people with schizophrenia, causal explanations concerning the aetiology of schizophrenia and the role of hospitals and society in treating people with schizophrenia. It was predicted that compared with the British and British Pakistanis, the Pakistanis would have more negative beliefs and attitudes, considering people with schizophrenia to be more dangerous and unpredictable; they were also expected to use more superstitious beliefs to explain the cause of schizophrenia and its symptoms; as well as believe more in seeking help from God and faith healers. There was strong evidence to suggest that Pakistanis possessed more negative beliefs and attitudes about people with schizophrenia, but there was no evidence to indicate that Pakistanis believed more in superstitious causal explanations. Pakistanis were more likely to consider seeking help from faith healers, but not God, compared with British Pakistanis and the British. Results confirm previous European-Asian difference in the understanding of the cause, manifestation and cure of schizophrenia. The impact of traditional and Western cultural influences on British Pakistanis is considered.

Evaluating the bio-energy potential of groundnut shell and sugarcane bagasse waste composite

OpenAIRE

Olatunde Ajani Oyelaran

2015-01-01

An assessment has been carried out on bio-coal briquettes from coal with sugarcane bagasse and coal with groundnut shell. Proximate analyses and elemental compositions of the coal and biomasses were determined. Different samples of briquettes were produced by blending varying composition of the coal with the biomasses in the ratio of 100:0; 90:10, 80:20, 70:30, 60:40, 50:50, 40:60 and 0: 100, using calcium carbonate as a desulfurizing agent and cassava starch as a binder. A manual hydraulical...

Sõda terroriga võib paisuda Pakistanis revolutsiooniks / Heiki Suurkask

Index Scriptorium Estoniae

Suurkask, Heiki, 1972-

2007-01-01

Sisepoliitilisest olukorrast Pakistanis. Eksiilis viibiv ekspeaminister Benazir Bhutto nõuab president Pervez Musharrafi tagasiastumist, samas pidas Musharraf temaga hiljuti läbirääkimisi. Erakorralist seisukorda Pakistanis ei kehtestatud. Lisa: Ameeriklaste asendamatu sõber Afganistani külje all

Use of grape must as a binder to obtain activated carbon briquettes

Directory of Open Access Journals (Sweden)

Deiana A. C.

2004-01-01

Full Text Available The results of studies on briquetting activated-carbon-based adsorbent materials, prepared from raw materials from the region of Cuyo, Argentina, are reported in this article. Several steps were carried out to obtain activated-carbon briquettes from Eucalyptus camaldulensis Dehn wood. These steps included carbonization of wood to obtain char; blending of char and a novel binder, i.e., grape must; formation of cylinder-like briquettes by pressure; and activation of the resulting material. The material was activated with steam under different temperatures, activation times, and activating agent flow rates. Impact resistance index, axial compressive strength, tensile strength by diametrical compression, BET area, and pore volume were measured for product characterization. Satisfactory surface areas and mechanical strengths were found in the final products.

Physical Properties of Biomass Fuel Briquette from Oil Palm ...

African Journals Online (AJOL)

ADOWIE PERE

of fuel briquettes in this study in order to supplement the energy mix of the nation. PKS was pulverized ... fossil fuel in the world market is impacting negatively ... useful products that can be applied in many sectors ... at 350 µm, 250 µm and 150 µm with Octagon digital ... formula is one of the models developed to accurately.

Briquettes of rice husk, polyethylene terephthalate (PET), and dried leaves as implementation of wastes recycling

Science.gov (United States)

Hariyanto, Sucipto; Usman, Mohammad Nurdianfajar; Citrasari, Nita

2017-06-01

This research aim is to determine the best briquettes as implementation of wastes recycle based on scoring method, main component composition, compressive strength, caloric value, water content, vollatile content, and ash content, also the suitability with SNI 01-6235-2000. Main component that used are rice husk, 2mm and 6 mm PET, and dried leaves. Composition variation in this research are marked as K1, K2, K3, K4, and K5 with 2 mm PET plastic and K1, K2, K3, K4, and K5 with 6 mm PET plastic. The total weight of the briquettes is 100 g and divided into 90% main components and 10% tapioca as binder. The compressive strength, caloric value, water content, vollatile content, and ash content were tested according to ASTM D 5865-04, ASTM D 3173-03, ASTM D 3175-02, ASTM D 3174-02. The tested results were used to determine the best briquette by scoring method, and the chosen briquettes is K2 with 6 mm PET plastic. The composition is 70% rice husk, 20% 6 mm PET plastic, and 10% dried leaves with the compressive strength, caloric value, water content, vollatile content, and ash content value is 51,55 kg/cm2; 5123 kal/g; 3,049%; 31,823%, dan 12,869%. The suitable value that meet the criteria according to SNI 01-6235-2000 is compressive strength, caloric value, water content, and ash content.

Process and device to produce fuel briquettes

Energy Technology Data Exchange (ETDEWEB)

Caroe, C J

1980-10-23

A two-stage process for the production of briquettes consisting essentially of cellulose (sawdust, peanut shells) is proposed. The fuel material (in case with additives) is molded by high pressure to pellets of the size of a few centimeters. The pellets are mixed with flammable binding agents like paraffin, wax, polyethylene etc. and molded at a lower pressure or extruded in a second step. A suited molding device is described. The wax content could be lowered with respect to known processes.

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

High-solid anaerobic digestion of corn straw for methane production and pretreatment of bio-briquette.

Science.gov (United States)

Li, Yeqing; Yan, Fang; Li, Tao; Zhou, Ying; Jiang, Hao; Qian, Mingyu; Xu, Quan

2018-02-01

In this study, an integrated process was developed to produce methane and high-quality bio-briquette (BB) using corn straw (CS) through high-solid anaerobic digestion (HS-AD). CS was anaerobic digested by using a leach bed reactor at four leachate recirculation strategies. After digesting for 28 days, highest methane yield of 179.6 mL/g-VS, which was corresponded to energy production of 5.55 MJ/kg-CS, was obtained at a higher initial recirculation rate of 32 L-leachate per day. Compared with bio-briquette manufactured from raw CS and lignite, the compressive, immersion and falling strength properties of bio-briquette made from AD-treated CS (solid digestate) and lignite were significantly improved. A preferred BB can be obtained with side compressive strength of 863.8 ± 10.8 N and calorific value of 20.21 MJ/kg-BB. The finding of this study indicated that the integrated process could be an alternative way to produce methane and high-quality BB with CS. Copyright © 2017 Elsevier Ltd. All rights reserved.

Substitutes for metallurgical coke in pyrometallurgical processes

Energy Technology Data Exchange (ETDEWEB)

Koshkarov, V.Ya.

1982-08-01

A briquetting process using sulphurous petroleum coke and a bituminous binder is described. The characteristics of briquettes made of petroleum coke, blends of coal and petroleum coke, and coal and metallurgical coke are compared. The prospect of replacing 25 to 50% of the metallurgical coke used in lime kilns with non-calcined petroleum coke briquettes is described. (4 refs.)

Traditional medicine among people of Pakistani descent in the capital region of Copenhagen.

Science.gov (United States)

Ramzan, Sara; Soelberg, Jens; Jäger, Anna K; Cantarero-Arévalo, Lourdes

2017-01-20

Studies show that ethnic minorities continue to use their cultural traditional medicines also after migration to the West. Research in this field is necessary, given that little is known about traditional medicines' impact on health-related problems. This study sheds light on the issue through a qualitative study among ethnic Pakistanis residing in Denmark. The study addresses perception, knowledge and attitudes regarding the use of medicinal plants among Pakistanis living in Copenhagen. We furthermore document and identify the medicinal plants used in households. Data were collected through in-depth, semi-structured interviews with sixteen ethnic Pakistanis aged 30-80 years. Interviews were transcribed verbatim and analysed through Emerson's two-phased analysis method. Medicinal plant products in the interviewees' households were collected, photographed, identified and deposited at Museum of Natural Medicine at University of Copenhagen. A total number of 121 Pakistani traditional medicines were identified, and found to represent both medicinal plants and foods. The average number of quoted Pakistani Traditional Medicines was 18 (N=16). Interviewees independently reported the same traditions for preparation and consumption of Pakistani traditional medicines. Factors that play a role in choosing to use Pakistani traditional medicines are frequent visits to Pakistan, belief in the healing power of totkas (homemade medicinal preparation), religious knowledge and the occurrence of recent illness within the family. Further, the upkeep of traditional use depends on the availability of Pakistani traditional medicines. The study enhanced understanding of ethnic Pakistanis' perception and continued use of traditional medicines within the household after migration to the West. In the context of Western biomedicine, little is known of the potential toxicity and side-effects of many of the Pakistani traditional medicines found to be used in households in Copenhagen. Copyright

Premium Fuel Production From Mining and Timber Waste Using Advanced Separation and Pelletizing Technologies

Energy Technology Data Exchange (ETDEWEB)

Honaker, R. Q.; Taulbee, D.; Parekh, B. K.; Tao, D.

2005-12-05

The Commonwealth of Kentucky is one of the leading states in the production of both coal and timber. As a result of mining and processing coal, an estimated 3 million tons of fine coal are disposed annually to waste-slurry impoundments with an additional 500 million tons stored at a number of disposal sites around the state due to past practices. Likewise, the Kentucky timber industry discards nearly 35,000 tons of sawdust on the production site due to unfavorable economics of transporting the material to industrial boilers for use as a fuel. With an average heating value of 6,700 Btu/lb, the monetary value of the energy disposed in the form of sawdust is approximately $490,000 annually. Since the two industries are typically in close proximity, one promising avenue is to selectively recover and dewater the fine-coal particles and then briquette them with sawdust to produce a high-value fuel. The benefits are i) a premium fuel product that is low in moisture and can be handled, transported, and utilized in existing infrastructure, thereby avoiding significant additional capital investment and ii) a reduction in the amount of fine-waste material produced by the two industries that must now be disposed at a significant financial and environmental price. As such, the goal of this project was to evaluate the feasibility of producing a premium fuel with a heating value greater than 10,000 Btu/lb from waste materials generated by the coal and timber industries. Laboratory and pilot-scale testing of the briquetting process indicated that the goal was successfully achieved. Low-ash briquettes containing 5% to 10% sawdust were produced with energy values that were well in excess of 12,000 Btu/lb. A major economic hurdle associated with commercially briquetting coal is binder cost. Approximately fifty binder formulations, both with and without lime, were subjected to an extensive laboratory evaluation to assess their relative technical and economical effectiveness as binding

Selected parameters of maize straw briquettes combustion

Directory of Open Access Journals (Sweden)

Kraszkiewicz Artur

2018-01-01

Full Text Available An analysis of the process of burning briquettes made of maize straw was performed. A number of traits have been evaluated, including physical characteristics of the fuel through parameters describing combustion kinetics as well as products and combustion efficiency. The study was conducted in a grate boiler, during which the differentiating factor was the air velocity flowing to the boiler. It was observed that the obtained values of the considered parameters were different, particularly temperature of the flue gas and the amount of CO and SO2 in the flue gas.

Determination of rust resistance genes in pakistani bread wheats

International Nuclear Information System (INIS)

Qamar, M.; Ahmad, S.D.; Rabbani, M.A.; Shinwari, Z.K.

2014-01-01

Stripe and leaf rusts are the major constraints to bread wheat production in Pakistan. Molecular markers were used to investigate the presence of leaf rust and stripe rust resistance gene cluster Lr34/Yr18 and stem rust resistance gene Sr2 in 52 Pakistani bread wheat cultivars/lines. PCR amplification of DNA fragments using DNA marker csLV-34 showed that 13 of the studied cultivars/lines, namely 03FJ26, NR 337, NR 339, NR 347, NR 350, Manthar, Margalla 99, Iqbal 2000, Saleem 2000, Wafaq 2001, Marwat 2001, Pirsabak 2004 and Fareed 2006 carry leaf rust and stripe rust resistance genes Lr34/Yr18. Stem rust resistance gene Sr2 was observed in 36 Pakistani spring wheat cultivars/lines using stm560.3tgag marker. The slow rusting gene Sr2 needs to be combined with additional stem rust resistance genes to establish durable resistance against Ug99 in modern wheat cultivars. Low frequency of Lr34/Yr18 was found in Pakistani wheats. This gene cluster needs to be incorporated into Pakistani wheats for durable rust resistance. (author)

Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

Energy Technology Data Exchange (ETDEWEB)

Bayraktur, K.N.; Lawson, G.J.

1984-09-01

Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lowerrank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy.

Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

Energy Technology Data Exchange (ETDEWEB)

Bayraktar, K.N.; Lawson, G.J.

1984-09-01

Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lower-rank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash yield and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy. 38 references.

Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (feasibility study of the environmentally friendly type coal utilization system in India); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The survey was conducted of the present situation of coal utilization and the present coal situation such as the environmental state of India which is a coal producing/consuming country next to China in Asia. The paper studied a feasibility of the introduction of the environmental friendly type coal utilization system` to be planned in India. The items for survey are the present situation of economy and energy and the future trend, environmental problems on coal utilization, the present status of the coal distribution system and study subjects, the present status of coal utilization by field and study subjects, a possibility of briquette use, a possibility of coal fluidization, electric power development plans and coal combustion technology in each industry, etc. The subjects are the obligation of coal preparation to coal thermal power plants 1000 km away from coal mines starting 2001, measures taken for effective ash use, measures taken for superannuated gas furnaces, etc. Based on the results of these site surveys and reports of the investigation under consignment from CMPDI, the paper studied/analyzed possibilities of introducing the coal utilization system having actual introduction results in Japan to India, and made an investigational report. 39 refs., 12 figs., 56 tabs.

Polymorphisms of the ABCB1 gene in the pakistani population

International Nuclear Information System (INIS)

Farhat, K.; Waheed, A.

2015-01-01

Objective: To investigate the frequency of the single nucleotide polymorphism C1236Tin exon 12 of the ABCB1 gene in Pakistani population and to compare it with published data on Asian and Caucasian populations. Study Design: Across-sectional observational study. Place and Duration of Study: Combined Military Hospital, Rawalpindi and Institute of Biomedical and Genetic Engineering (IBGE), Islamabad, from August 2012 to May 2013. Methodology: C1236T polymorphism was investigated in 426 Pakistani subjects. The frequency was compared with the published data on other Asian and Caucasian populations. Results: The frequencies of ABCB1 C1236T were 16.4% for CC, 44.1% for CT and 39.4% for TT. Pakistanis differed significantly from all the European populations compared in the distribution of the TT genotype of C1236TABCB1 (p < 0.05). The Pakistani population also differed significantly from some of the European populations in the distribution of CC and CT genotype (p < 0.05). Conclusion: There was significant difference in the genotype frequency of the ABCB1 gene compared to other populations. This study has provided a framework for future pharmacogenetic and pharmacokinetic studies on this polymorphic variant of ABCB1 gene in the Pakistani population. (author)

Coal materials for the reduction of SO{sub 2}-NO{sub x}; Derivados del carbon para la reduccion de SO{sub 2}-No{sub x}

Energy Technology Data Exchange (ETDEWEB)

1999-09-01

The project was divided in two well-differentiated parts: SO{sub 2} removal and NO{sub x} reduction. In both cases, carbon materials play a unique role in the processes, either as calcium sorbent suppor (SO{sub 2} removal) or as catalyst support and reducing agent (NO{sub x} reduction). Removal of SO{sub 2}. This process was carried out by calcium sorbents at relatively low temperature (T<300 degree centigree), forming CaSO{sub 3} (instead of CaSO{sub 4}) that decomposos at lower temperatures, making regeneration easier. High dispersion of the active species, CaO, has been obtained using carbon materials (activated carbons, chars, etc.) and other inorganic compounds as supports. The effect of oxygen, carbon dioxide and steam in the reaction atmosphere and the regeneration process have been also investigated. Thermal regeneration is possible for several cycles, however, carbon gasification also takes place. To control, and to void that effect, the reaction and regeneration temperatures should be carefully controlled and carbons with low reactivity should be selected. The process was scaled (100-2000) using briquete samples obtained by physical mixture of char and Ca(oh){sub 2}. The SO{sub 2} removal levels were similar to those found in the laboratory scale. NO{sub x} reduction. The possibility of using potassium containing coal-briquettes for NO and NO{sub x} reduction has been investigated. The preparation method of briquettes presents the advantage of using a binder agent (humic acid) which contains the catalyst (potassium). The system catalyst-binder-coal stays intimately joined by a moulding stage and subsequent pyrolysis, providing proper mechanical resistance to the coal-briquettes. With the purpose to improve the briquettesactivity, different variables of the preparation process have been investigated (potassium content-added with the binder and/or KOH-, rank and mineral matter content of the coal precursor, pyrolysis temperature and pressure of the moulding

Physical and chemical evaluation of furniture waste briquettes.

Science.gov (United States)

Moreno, Ana Isabel; Font, Rafael; Conesa, Juan A

2016-03-01

Furniture waste is mainly composed of wood and upholstery foam (mostly polyurethane foam). Both of these have a high calorific value, therefore, energy recovery would be an appropriate process to manage these wastes. Nevertheless, the drawback is that the energy content of these wastes is limited due to their low density mainly that of upholstery foam. Densification of separate foam presents difficulties due to its elastic character. The significance of this work lies in obtaining densified material by co-densification of furniture wood waste and polyurethane foam waste. Densification of furniture wood and the co-densification of furniture wood waste with polyurethane foam have been studied. On the one hand, the parameters that have an effect on the quality of the furniture waste briquettes have been analysed, i.e., moisture content, compaction pressure, presence of lignin, etc. The maximum weight percentage of polyurethane foam that can be added with furniture wood waste to obtain durable briquettes and the optimal moisture were determined. On the other hand, some parameters were analysed in order to evaluate the possible effect on the combustion. The chemical composition of waste wood was compared with untreated wood biomass; the higher nitrogen content and the concentration of some metals were the most important differences, with a significant difference of Ti content. Copyright © 2016 Elsevier Ltd. All rights reserved.

Influence of Addition of Briquettes with Dust Content into the Charge of Electric Induction Furnace on Cast Iron Quality

Directory of Open Access Journals (Sweden)

Pribulová A.

2012-09-01

Full Text Available Foundry dust from blasting and grinding of castings contain a high amount of iron, ergo it is possible its recycling in foundry process. Dust was compacted by briquetting, two kinds of briquettes were prepared (A contained 95% magnetic part of dust from casting blasting +5% bentonite and B contained 95% mixture of dust from casting grinding and magnetic part of dust from casting blasting + 5% bentonite and used as a part of charge into the electric induction furnace. It was found that addition of briquettes has had an influence of a chemical composition of cast iron above all on content of sulphur, phosphorus and silicon. It was not reflected in decrease in tensile strength and in microstructure. Yield of metal from briquettes was not lower then 70%.

Influence of Addition of Briquettes with Dust Content into the Charge of Electric Induction Furnace on Cast Iron Quality

Directory of Open Access Journals (Sweden)

A. Pribulová

2012-09-01

Full Text Available Foundry dust from blasting and grinding of castings contain a high amount of iron, ergo it is possible its recycling in foundry process.Dust was compacted by briquetting, two kinds of briquettes were prepared (A contained 95% magnetic part of dust from casting blasting+5% bentonite and B contained 95% mixture of dust from casting grinding and magnetic part of dust from casting blasting + 5%bentonite and used as a part of charge into the electric induction furnace. It was found that addition of briquettes has had an influence of a chemical composition of cast iron above all on content of sulphur, phosphorus and silicon. It was not reflected in decrease in tensile strength and in microstructure. Yield of metal from briquettes was not lower then 70%.

Metallization of Extruded Briquettes (BREX in Midrex Process

Directory of Open Access Journals (Sweden)

Aitber Bizhanov

2017-07-01

Full Text Available The results of the full-scale testing of the Extruded Briquettes (BREX as the charge components of the industrial Midrex reactor are discussed. The influence of the type of binder on the degree of metallization of BREX is analyzed. Magnesium sulfate-based binder helps to reach highest metallization degree of BREX. Mineralogical study shows the difference in the iron-silicate phase’s development as well as in the porosity change during metallization depending on the binder used.

An Investigation of Generic Structures of Pakistani Doctoral Thesis Acknowledgements

Science.gov (United States)

Rofess, Sakander; Mahmood, Muhammad Asim

2015-01-01

This paper investigates Pakistani doctoral thesis acknowledgements from genre analysis perspective. A corpus of 235 PhD thesis acknowledgements written in English was taken from Pakistani doctoral theses collected from eight different disciplines. HEC Research Repository of Pakistan was used as a data sources. The theses written by Pakistani…

Torrefaction of briquettes: technical-economic feasibility and perspective in Brazilian market; Briquetes torreficados: viabilidade tecnico-economica e perspectivas no mercado brasileiro

Energy Technology Data Exchange (ETDEWEB)

Felfli, Felix Fonseca; Luengo, Carlos Alberto [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Inst. de Fisica Gleb Wataghin. Grupo Combustiveis Alternativos; Rocha, Jose Dilcio [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Nucleo Interdisciplinar de Planejamento Energetico

2004-07-01

It is presented an study of the operational impact into a briquettes factory produced by the introduction of a torrefaction process. Through costs analysis it is shown that for a briquettes factory of 1.200 ton/year capacity, it is possible to increase Operational Profits and decrease the Break Even Point in 15.7 % when a torrefaction reactor is introduced into the manufacturing line. So, it is possible to insure that torrefaction increase the overall system efficiency without increasing yearly production since the number of 'biomass fuels' is increased enabling operation in other markets. This study also shows that torrefaction improves briquettes quality allowing access to the comparatively smaller consumer market still unreached by biomass briquets. (author)

The design of financial recording system in industrial bio-briquette of Ramie (Boehmeria nivea) decortication waste with design thinking approach

Science.gov (United States)

Irianto, R.; Purnomo, D.; Prima, S.; Wulandari, A.

2017-05-01

The production process of ramie (boehmeria nivea) fibers generates waste which contents 5.95 to 7.83% ash; 1.88 to 2.87% silicate; 30.67 to 31.08% lignin; 33.81 to 35.99% alpha cellulose; 62.95 to 63.78% holoselulosa; 17.43 to 18.14% pentosan, which can be used as raw material of bio-briquette. Those potential can be used to generate a business opportunity, such as industrial bio-briquette of ramie decortication waste. The purpose of this research is to create accounting information which could present an income statement that is easily applied on industrial bio-briquette of ramie decortication waste. This research use descriptive analysis method with design with design thinking approach to gather the information through depth observation on human being as the object to achieve the purpose. The result in this research is financial recording system of industrial bio-briquette of ramie decortication waste in a desktop application. The system is integrated with production activities according to the needs of accounting information particularly at managerial production. The existing applications creates information in the form of financial operations which can be used as a factor in decision-making.

Pattern of vitamin D among Pakistani pregnant women

International Nuclear Information System (INIS)

Nasir, J.A.; Zaidi, S.A.A.

2018-01-01

Vitamin D deficiency is an emerging health concern around the world, highly prevalent in south Asian population, despite abundant sunlight. In Pakistan, all age groups are vulnerable to Vitamin D deficiency including pregnant women. This systematic review aimed to determine the pattern of Vitamin D deficiency among Pakistani pregnant women as well as exploring the causes and possible interventions that have had a substantial effect on improving the vitamin D level. Three databases (PubMed, Pub Get and Google Scholar), for the present review up to 2016, were used for the identification of published peer reviewed original relevant studies regarding Vitamin D deficiency among Pakistani pregnant women with the keywords Vitamin D or 25-hydroxyvitamin D or 25(OH)D in combination with pregnant women. Five studies were included for the final analysis. Vitamin D deficiency was common and highly prevalent among Pakistani pregnant women and their neonates. The main reasons for this were found to be avoiding sun exposure, quality of diet, and lower intake of calcium. Maternal vitamin D supplementation was found to be a key intervention to improve the maternal and neonatal vitamin D status. These review findings can be emerging in ensuring the adequate vitamin D level for Pakistani pregnant women during pregnancy, ultimately to achieve positive maternal and neonate's health outcomes. (author)

Pakistani labour emigration: new destinations in Europe

Directory of Open Access Journals (Sweden)

Nasra M. Shah

2005-01-01

Full Text Available In the first part of this paper a historical overview is made of Pakistani labour emigration to the countries of the Persian Gulf, and to Anglo-Saxon countries in general and to the United Kingdom in particular. In the second part of the paper the new European labourmarkets which Pakistani emigrants have been increasingly discovering is analyzed. In this sense, Spain has become one of the new destinations. The author goes on to point out the specific nature of this new situation and at the same time details some of the future implications for Spain.

Pakistani president korraldas riigipöörde ülemkohtunike vastu / Heiki Suurkask

Index Scriptorium Estoniae

Suurkask, Heiki, 1972-

2007-01-01

Pakistani president Pervez Musharraf kuulutas riigis välja erakorralise seisukorra, Pakistani ajalehe hinnangul on tegemist riigipöördega ülemkohtu vastu. Peaminister Shaukat Azizi kinnitusel on arreteeritud ligi 500 inimest

Statistical experimental design approach in coal briquetting

Energy Technology Data Exchange (ETDEWEB)

B. Salopek; S. Pfaff; R. Rajic

2003-07-01

The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation. 2 refs., 2 figs., 5 tabs.

Physical Properties of Biomass Fuel Briquette from Oil Palm Residues

African Journals Online (AJOL)

Palm Kernel Shell (PKS) and Mesocarp Fibre (MF) were used for the production of fuel briquettes in this study in order to supplement the energy mix of the nation. PKS was pulverized and then sieved into different grain particles of 350 μm, 250 μm and 150 μm, before mixing with MF in the ratios: 90:10, 80:20 and 70:30 ...

Determination of Particle Size and Distribution through Image-Based Macroscopic Analysis of the Structure of Biomass Briquettes

Directory of Open Access Journals (Sweden)

Veronika Chaloupková

2018-02-01

Full Text Available Via image-based macroscopic, analysis of a briquettes’ surface structure, particle size, and distribution was determined to better understand the behavioural pattern of input material during agglomeration in the pressing chamber of a briquetting machine. The briquettes, made of miscanthus, industrial hemp and pine sawdust were produced by a hydraulic piston press. Their structure was visualized by a stereomicroscope equipped with a digital camera and software for image analysis and data measurements. In total, 90 images of surface structure were obtained and quantitatively analysed. Using Nikon Instruments Software (NIS-Elements software, the length and area of 900 particles were measured and statistically tested to compare the size of the particles at different surface locations. Results showed statistically significant differences in particles’ size distribution: larger particles were generally on the front side of briquettes and vice versa, smaller particles were on the rear side. As well, larger particles were centred in the middle of cross sections and the smaller particles were centred on the bottom of the briquette.

Effect of biomaterials and working pressure of a briquetting machine on physical characteristics and energy consumption of briquette production

Directory of Open Access Journals (Sweden)

Niedziółka Ignacy

2018-01-01

Full Text Available The paper presents an analysis of the influence of biomaterials and working pressure of a briquetting machine on physical characteristics and energy consumption of briquette production. The following types of biomaterials were used in the study: rape, oat and maize straw. Hydraulic piston briquetting machine JUNIOR manufactured by Deta Polska was used for briquetting. During the briquetting process, the working pressures of briquetting machine were 20, 26 and 32 MPa. Depending on the type of biomaterial used and the assumed working pressure of briquetting machine, produced briquettes differed in terms of both their physical characteristics and energy consumption. Based on the analysis of the obtained results, it was found that physical characteristics and energy consumption during briquette production were influenced by such factors as the type of compacted material, its fragmentation as well as granulometric composition and working pressure of the briquetting machine used.

[Emission characteristics of PM10 from coal-fired industrial boiler].

Science.gov (United States)

Li, Chao; Li, Xing-Hua; Duan, Lei; Zhao, Meng; Duan, Jing-Chun; Hao, Ji-Ming

2009-03-15

Through ELPI (electrical low-pressure impactor) based dilution sampling system, the emission characteristics of PM10 and PM2.5 was studied experimentally at the inlet and outlet of dust catchers at eight different coal-fired industrial boilers. Results showed that a peak existed at around 0.12-0.20 microm of particle size for both number size distribution and mass size distribution of PM10 emitted from most of the boilers. Chemical composition analysis indicated that PM2.5 was largely composed of organic carbon, elementary carbon, and sulfate, with mass fraction of 3.7%-21.4%, 4.2%-24.6%, and 1.5%-55.2% respectively. Emission factors of PM10 and PM2.5 measured were 0.13-0.65 kg x t(-1) and 0.08-0.49 kg x t(-1) respectively for grate boiler using raw coal, and 0.24 kg x t(-1) and 0.22 kg x t(-1) for chain-grate boiler using briquette. In comparison, the PM2.5 emission factor of fluidized bed boiler is 1.14 kg x t(-1), much her than that of grate boiler. Due to high coal consumption and low efficiency of dust separator, coal-fired industrial boiler may become the most important source of PM10, and should be preferentially controlled in China.

Comparative Analysis of the Indian and Pakistani Nuclear Energy Development Programmes

Directory of Open Access Journals (Sweden)

A. A. Boyko

2015-01-01

Full Text Available Due to the traditional competition between India and Pakistan, their strategic fields developing are interdependent. Nuclear power development programs are concerned as well. Pakistan falls behind India in this branch, however the specifics of the nuclear infrastructure let the potential of the states be relatively balanced. After Nuclear Suppliers Group granted a waiver to India in 2008 and Russia, France and USA, the new participants, broke into the market, India obtained an opportunity to make a breakthrough in the national nuclear program development, thus violating a status quo in fuel cycle technologies. Such chances stimulated China to violate the NSG guidelines and non-proliferations principles to get involved in Pakistani nuclear program development. The nuclear power Indian-Pakistani competition prospects largely depend on the Chinese position. Despite the international community suspects the Pakistani officials in nuclear black market dealing and the NSG guidelines China obviously supports the Pakistani nuclear field. This may result in preventing of escalation of tensions in the region. 

OPTIMASI PROSES PEMBUATAN BRIKET BIOMASSA MENGGUNAKAN METODE TAGUCHI GUNA MEMENUHI KEBUTUHAN BAHAN BAKAR ALTERNATIF YANG RAMAH LINGKUNGAN (Optimization of Biomass Briquettes Production Process Using Taguchi Method

Directory of Open Access Journals (Sweden)

Musabbikhah Musabbikhah

2015-03-01

Full Text Available ABSTRAK Permasalahan yang dihadapi pembuat dan pengguna briket adalah briket yang dihasilkan kualitasnya rendah ditinjau dari nilai kalor. Tujuan penelitian ini adalah menentukan kualitas briket terbaik dari limbah biomassa dalam memenuhi kebutuhan bahan bakar alternatif rumah tangga yang murah dan ramah lingkungan guna mewujudkan masyarakat mandiri energi. Metode yang digunakan untuk menentukan kualitas briket adalah metode Taguchi. Variabel bebas dalam penelitian ini adalah tekanan pengepressan, waktu penahanan, model cetakan, suhu pengeringan, lama pengeringan dan komposisi bahan, sedangkan variabel terikat adalah nilai kalor briket. Hasil penelitian menunjukkan bahwa kualitas briket terbaik ditinjau dari nilai kalor tertinggi yaitu pada setting parameter A2B1C2D2E2F1, artinya tekanan pengepressan 225 kg/cm2, waktu penahanan 5 menit, model cetakan sarang tawon (kotak, suhu pengeringan 60 °C, lama pengeringan 3 hari, perbandingan limbah jarak pagar : arang sekam : arang tempurung kelapa : perekat adalah 5 : 3: 2 : 1. Rata-rata nilai kalor biobriket yang dihasilkan sebesar 5.323 kal/g. Hal ini menunjukkan bahwa briket mempunyai nilai kalor yang tinggi dan memenuhi SNI, sehingga briket layak untuk memenuhi kebutuhan bahan bakar alternatif yang ramah lingkungan. ABSTRACT Problems that encountered on manufacturers and users of briquettes is low quality of the briquettes in terms of heat value. The aim of this research is to determine the best quality of the briquette which is made from biomass waste. The briquette is expected to be used to fulfill the need of inexpensive and environmentally friendly of alternative household fuel, by which the energy independent community could be realized.The method used to determine the quality of the briquette is Taguchi method. The independent variables involved are compressive strength, holding time, mold model, drying temperature, drying time and material composition. The dependent variable is the highest

FY 1999 report on the potential survey of the environmentally friendly type coal utilization system. Potential survey of the environmentally friendly type coal utilization system in the Philippines; 1999 nendo chosa hokokusho. Kankyo chowa gata sekitan riyo system kanosei chosa (Firipin ni okeru kankyo chowa gata system kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of contributing to working out a master plan for the introduction of the environmentally friendly type coal utilization system in the Philippines, analysis was made of the state of coal use/the state of spread by industry mostly including the electric power industry, cement industry and residential/commercial use fuel sector. In the Philippines, the amount of coal use has rapidly been increasing since coal-fired power plants started operation. For the promotion of the use of domestic coals, it is important to reform low grade coal. Moreover, the technology is required which copes with the reinforced regulation against SOx emissions. In the cement industry, coal and coal ash have not yet been effectively used. Therefore, the following measures should be taken to increase the competitive force: energy conservation measures, reinforcement of environmental measures such as dust prevention, and effective use of the fly ash emitted from power plants. In general households and small-/medium-sized industries such as tobacco drying, they still use a large amount of charcoals and firewood, which is approximately 86% of the residential/commercial use energy. There is a growing tendency for the development/spread of coal briquette as substituting energy. (NEDO)

Stories of pain and health by elderly Pakistani women in Norway.

Science.gov (United States)

Sverre, Beate Lie; Solbrække, Kari Nyheim; Eilertsen, Grethe

2014-11-01

This ethnographic study investigates the stories of elderly Pakistani women living in Norway. Migration studies indicate that elderly migrant women are passive, ill victims caught in a marginalized position due to age, ethnicity and gender, and thus have little access to opposition and agency. To broaden the picture it is necessary to develop an innovative approach to understand what is implicated in the process of migration. The importance of considering life conditions that surrounds potential health promotion behaviors of immigrants is stressed by several researchers. However, up to now limited research guided by this perspective has been done in Norway. Therefore, this study explored how elderly Pakistani women in Norway promote their health and well-being through some distinct social interactions. The intention is to bring awareness to how health, even by so-called disadvantaged social groups, may take place. These practices are important to take into consideration when developing health-promoting policies for elderly immigrants. An ethnographic study of 15 Pakistani women, aged 53-75, was carried out in a multisided fieldwork in Oslo using participant observation and ethnographic interviews. The analytical approach was inspired by the constructivist theoretical framework of narrative ethnography. The elderly Pakistani women in Norway construct stories of living in-between cultures and experiences of acculturative stress caused by being elderly, immigrants and women. However, this analysis also suggests that through distinct social relationships, primarily in the context of a voluntary organization, elderly Pakistani women do health by the way they interact and construct a repertoire of social identities. The healing practices taking place among elderly Pakistani women may counteract the negative health outcomes associated with age, migration and gender implications for immigrant health-promoting policy in Norway may be to increase the establishment and

Traditional medicine among people of Pakistani descent in the capital region of Copenhagen

DEFF Research Database (Denmark)

Ramzan, Sara; Soelberg, Jens; Jäger, Anna K

2017-01-01

ETHNOPHARMACOLOGICAL RELEVANCE: Studies show that ethnic minorities continue to use their cultural traditional medicines also after migration to the West. Research in this field is necessary, given that little is known about traditional medicines' impact on health-related problems. This study sheds...... light on the issue through a qualitative study among ethnic Pakistanis residing in Denmark. AIM OF THE STUDY: The study addresses perception, knowledge and attitudes regarding the use of medicinal plants among Pakistanis living in Copenhagen. We furthermore document and identify the medicinal plants...... Traditional Medicines was 18 (N=16). Interviewees independently reported the same traditions for preparation and consumption of Pakistani traditional medicines. Factors that play a role in choosing to use Pakistani traditional medicines are frequent visits to Pakistan, belief in the healing power of totkas...

Determination of Calorific Ability of Fuel Briquettes on the Basis of Oil and Oil Slimes

Science.gov (United States)

Fedyaeva, O. A.; Poshelyuzhnaya, E. G.; Rakhmatulina, E. M.; Zakharov, V. A.; Fisenko, T. E.

2018-01-01

Utilization and neutralization of oil slimes is one of important environmental problems of the oil-extracting, oil-processing and petrochemical industry. The easiest and economic way of utilization of oil slimes is their use as a part of the bricketed boiler fuel. In this work the highest calorific ability of crude oil, the oil slimes and fuel briquettes made on their basis is defined. A research problem was carrying out the technical analysis of oil fuels on the content in them analytical moisture, the cindery rest and volatiles. It is established that in comparison with oil slimes crude oil possesses bigger highest calorific ability, has smaller humidity and an ash-content. The highest calorific abilities of the boiler briquettes made of samples of crude oil, oil slimes and peat made 14 - 26 MJ/kg.

Optimization of the technology of fodder briquettes-licks with the use of a steam compression heat pump

Directory of Open Access Journals (Sweden)

L. I. Lytkina

2017-01-01

Full Text Available In conditions of industrial maintenance of animals, their health is noticeably weakening, in the majority of the body, profound metabolic disorders are noted, and productivity is reduced. In such conditions it is necessary to use feed additives in the form of briquettes-licks, able to compensate for the lack of micro and macro elements, vitamins and many other substances. Intensification of feed production through the use of new advanced technologies allows to improve the quality of products and reduce losses in its production. The technologies used for briquettes-licks and equipment for their production do not always allow to provide high quality products and achieve the necessary effect when fed. In addition, they are energy-intensive, do not imply the use of secondary energy carriers. Therefore, the creation of a functional product, combining a complex of substances necessary for animal feeding, and the development of an energy-efficient method for its production is topical. The proposed technology makes it possible to obtain feed briquettes with high homogeneity and a specified content of biologically active substances, to ensure a longer-term preservation of the products. The developed line provides for the maximum rapid cooling of the finished product and a reduction in the specific energy consumption for its production as a result of the heat of spent coolants. The high-quality licks produced were homogeneous in their composition, resistant to unfavorable conditions. They are characterized by a higher stability of structural and mechanical properties and stability of storage quality for a long time: after twelve months, the technological properties of the products have not changed, signs of damage associated with increased humidity of the environment have not been noted. On the surface of briquettes, signs of development of microflora were not observed. The values of microbiological quality indicators were within acceptable limits. The

FY 2000 report on the potential survey of the environmentally-friendly coal utilization system. Survey of the applicability of low grade coal reformation technology in Indonesia; 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Indonesia ni okeru teihin'itan kaishitsu gijutsu no tekiyosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Survey was made of the case of applying the low grade coal reformation technology to commercial plants in Indonesia. In the survey, supposing the UBC process as reformation technology and 5,000 t/d as size of the commercial plant, studies were made of companies to be applied, schemes on the usable fund raising/governmental supporting policy, potential diffusion/effects of diffusion, facilities which can be domestically manufactured/subjects in promoting the domestic manufacture, economic F/S, etc. Different from the first generation coal companies, the second generation coal companies own low grade coal for the most part of the coal resource. Therefore, the companies are very much interested in the reformation technology. In the financial plan, the equipment cost of a commercial plant of this size was estimated at approximately 10 billion yen. This is a large initial investment for coal companies in Indonesia. So, it is necessary to consider a system of joint venture with Japanese users, etc. As to the study of the economical efficiency, the trial calculation indicated that the reformation cost was 7.35 US$/product ton and the price of reformed coal briquette product was 19.85 US$/product ton. In this case, ROI (return on investment) of 8.40%/year was expected. (NEDO)

Relationship of Life Satisfaction and Job Satisfaction among Pakistani Army Soldiers

OpenAIRE

Summaira Naz

2015-01-01

The present study had two main objectives; first, to discover the relationships between job satisfaction and life satisfaction in Pakistani army soldiers, second, to find out the age, salary, marital status, and education differences on job satisfaction and life satisfaction in Pakistani army soldiers. In the present study two questionnaires; Job Satisfaction Scale JSS (Macdonald & Maclntyre, 1997) and Satisfaction With Life Scale (Diener, ...

Bushi lepituskatse vallandas Pakistani ja Afganistani juhi teineteise süüdistamise / Triin Oppi

Index Scriptorium Estoniae

Oppi, Triin

2006-01-01

USA, Pakistani ja Afganistani presidendid leppisid kokku luureandmete vahetamises ja tõhusamas koostöös terroristide alistamiseks. Pakistani ja Afganistani presidentide Pervez Musharrafi ja Hamid Karzai omavahelised süüdistused

Energy and Resource-Saving Sources of Energy in Small Power Engineering of Siberia

Directory of Open Access Journals (Sweden)

Baranova Marina

2017-01-01

Full Text Available The sustainable development of distant areas of Siberia is associated with the structures of energy demand and supply, the implementation and promotion of the process of environmentally safe restructuring of the energy supply system. It has been established that suspension coal fuels derived from brown coal, coal mining, coal processing wastes can be used as fuel. The results of experimental and industrial boilers on suspension water coal fuel are presented. The designs of vortex combustion chambers of various powers are developed and tested. The possibility of using coal-enrichment wastes and substandard coals for the production of manure-coal fuel briquettes was studied. It is shown that the strength and thermal power characteristics of briquettes depend on the moisture content and degree of metamorphism of the raw materials. The most effective percentage of the solid phase and manure, as a binder, was determined.

Suitsiiditerrorist tappis Pakistani tipp-poliitiku / Kaivo Kopli

Index Scriptorium Estoniae

Kopli, Kaivo

2007-01-01

Pakistanis tapeti endine peaminister Benazir Bhutto. Samuti endise peaministri Navaz Sharifi juhitav opositsioonipartei, mis kavatses valimistel osaleda, otsustas valimiste boikotiga liituda. B. Bhutto isast ja vendadest. Lisa: Lääne haridusega huntade vastu võitleja

Pakistani Students' Perceptions about Use of the Internet in Their Academic Activities

Science.gov (United States)

Ali, Zarqa S.

2014-01-01

The aim of the study is to explore Pakistani university students' use of the Internet in their studies and their perceptions of online academic life. Findings show that Internet use for academic purposes has both positive and negative aspects. There is a gender difference in Pakistani students' perceptions about the use of the Internet in their…

Kauge rahva tragöödia : Eesti Päästemeeskond Pakistanis / Mati Raidma

Index Scriptorium Estoniae

Raidma, Mati, 1965-

2006-01-01

Eesti Päästemeeskonna ehk EDRT (Estonian Disaster Relief Team) missioonist Pakistani maavärina piirkonda 11.-25. oktoobril 2005. a. Kommenteerib meeskonna juht Tauno Suurkivi. Vt. samas: Rivo Salong. Eesti Päästemeeskonna logistikameeskond Pakistanis. Kommenteerib Eesti Päästemeeskonna otsingu-päästerühma juht Gert Teder

LACK OF AWARENESS ABOUT SAFE BLOOD IN PAKISTANI POPULATION

Directory of Open Access Journals (Sweden)

Muhammad Usman

2014-12-01

Full Text Available Blood transfusion is a life saving procedure in various transfusion-dependent life threatening conditions and donation of safe blood is a prerequisite for achieving this goal. This study was designed to evaluate the awareness regarding “safe blood” in Pakistani population. This study was conducted at a large scale through a population survey. The test population was divided into two groups i.e. general population and students. The Performa was designed for a general and student population and included 20 questions related to awareness of safe blood. A total of 4900 individuals belonging to different ethnic groups were included in this population survey. Results of social survey were analyzed by using Usman and Moin awareness chart. Results of this study revealed profound unawareness about safe blood in Pakistani population. This study found lack of awareness about safe blood as a major factor that is playing a vital role in the propagation of blood borne diseases in Pakistan. To secure the recipients from blood borne complications through blood donation, it is necessary to create effective awareness about safe blood in Pakistani population.

Relationship of Life Satisfaction and Job Satisfaction among Pakistani Army Soldiers

Directory of Open Access Journals (Sweden)

Summaira Naz

2015-03-01

Full Text Available The present study had two main objectives; first, to discover the relationships between job satisfaction and life satisfaction in Pakistani army soldiers, second, to find out the age, salary, marital status, and education differences on job satisfaction and life satisfaction in Pakistani army soldiers. In the present study two questionnaires; Job Satisfaction Scale JSS (Macdonald & Maclntyre, 1997 and Satisfaction With Life Scale (Diener, et al., 1985; were administered to a sample (N=400 along with a demographic sheet. The results of the study revealed a significant positive correlation between job satisfaction and life satisfaction of Pakistani army soldiers. The findings of the study also showed a significant age, education, salary, and marital status differences in job satisfaction and life satisfaction. Age, marital status, and salary variables had positive correlation with job satisfaction and life satisfaction but education had a negative association with job satisfaction and life satisfaction

Access to Power: Governance and Development in the Pakistani Electrical Power Sector

Science.gov (United States)

Naqvi, Ijlal

This dissertation explores governance in Pakistan through a study of the state-run electrical power sector. At both the micro and macro level, the Pakistani power sector provides a lens into the heart of the Pakistani state and its governance institutions. This ethnographic and historical study offers an in-depth look at state operations in a developing country, situates the current Pakistani power crisis in a larger context of continuity through periods of dictatorship and democracy, and suggests how efforts to make state service delivery more responsive to citizens might be reconceived. A historical review of the Pakistani power sector establishes first and foremost that the current crisis is the product of longer-term processes for which the policy solutions currently being proposed (with the support of international donors and multilateral lenders) are inadequate. Depoliticized attempts at power sector reform have little to offer in light of the pervasively informal and negotiated nature of the fragmented Pakistani state. The institutions of power sector governance are mutually constituted by the formal rules and the informal---personal relationships, language, violence, money, and power. These rules of the game are as relevant to relations within and between public sector organizations as they are to the engagement of citizens with their state. The same rules apply at the margins of the state---informal squatter settlements---as at the core, though the resources brought to bear and the resultant outcomes are different. The internal incoherence of this state underscores the limitations of formal rules in determining outcomes, and the poor prospects for reform efforts that focus exclusively on the formal aspects of governance. To proactively engage with the question of political will leads away from top-down policy perspectives and counter to the depoliticizing tendencies that currently shape policy reforms. Instead, an energized and informed local participation

Perceptions of Disease State Management Among Pakistani ...

African Journals Online (AJOL)

Purpose: To explore the perceptions of disease state management among Pakistani hypertensive patients. Methods: A focus group discussion was conducted with 19 hypertensive patients in order to obtain an insight into their self-management practices. The study was conducted in Sandeman Provincial Hospital, Quetta, ...

Supporting Pakistani and Chinese families with young children: perspectives of mothers and health visitors.

Science.gov (United States)

Hogg, R; de Kok, B; Netto, G; Hanley, J; Haycock-Stuart, E

2015-05-01

In the UK, public health nurses (health visitors) provide support and advice to families with young children, including those from minority ethnic communities. While the need for cultural sensitivity is being increasingly recognized, the factors which contribute to this sensitivity are poorly understood. The Pakistani and Chinese communities constitute the two largest minority ethnic groups in Scotland. This study explored Pakistani and Chinese women's experience of motherhood and of the health visiting service and public health nurses' experiences of working with Chinese and Pakistani mothers. Semi-structured individual interviews were carried out with 16 Pakistani and 15 Chinese mothers. Eight health visitors took part in two focus groups. The study was undertaken in an urban area of Scotland. Data were analysed thematically. Chinese and Pakistani mothers negotiate complex processes in order to ensure that their children maintain their own ethnic identity while fitting in with their peers in their adopted country. Health visitors were seen as supportive, although sometimes advice and information given was culturally inappropriate, and their role was often poorly understood. Health visitors were anxious to be sensitive to families' religious and cultural beliefs. Cultural sensitivity is an important factor in providing appropriate advice and help to Pakistani and Chinese families, and involves health visitors in considering views and practices on parenting which may differ across cultures, including their own. Family characteristics need to be understood on an individual basis, rather than making assumptions about clients' cultural norms and lifestyles. This is best achieved by exploring with mothers if they understand the advice and information they are being offered and also if it is appropriate to their cultural and religious beliefs. © 2014 John Wiley & Sons Ltd.

CONSANGUINITY, GENETICS AND DEFINITIONS OF KINSHIP IN THE UK PAKISTANI POPULATION.

Science.gov (United States)

Bittles, A H; Small, N A

2016-11-01

Consanguineous marriage is a controversial topic in many Western societies, with attention mainly focused on the health of immigrant communities from Asia and Africa. In the UK consanguinity is especially prevalent in the Pakistani community, which now numbers over 1.1 million. Less attention has been paid to the influence of hereditary population stratification within Pakistani communities, in particular biraderi (literally brotherhood) membership, which denotes male lineages that largely govern marriage partner choice and hence the transmission of disease genes. The various roles played by biraderi and their relationship to other socio-occupational and kinship terms, such as caste, quom and zat, are often overlooked in health-based studies. The interchangeable use of these different kinship terms without rigorous definition can create identity uncertainty and hinders inter-study comparisons. Where feasible, standardization of terminology would be both desirable and beneficial, with biraderi the preferred default term to identify specific social and genetic relationships within the Pakistani diaspora.

Power generation from lignite coal in Bulgaria - problems and solutions

International Nuclear Information System (INIS)

Batov, S.; Gadjanov, P.; Panchev, T.

1997-01-01

The bulk of lignite coal produced in Bulgaria is used as fuel for the thermal power plants (TPP) built in Maritsa East coal field. A small part of it goes to production of briquettes and to fuel the auxiliary power plants of industrial enterprises. The total installed capacity of the power plants in the region of Maritsa East is 2490 MW, and the electric power generated by them is about 30% of the total power generated in the country. It should be noted that these power plants were subjected to a number of rehabilitations aiming to improve their technical and economic parameters. Irrespective of that, however, solution has still to be sought to a number of problems related to utilisation of the low-grade lignite coal for power generation. On the whole, they can be divided in the following groups: Those related to lignite coal mining can be referred to the first group. Lignite coal is mined in comparatively complicated mining and geological conditions characterized mainly by earth creep and deformation. The second group of problems is related to coal quality control. It is a fact of major significance that the quality indices of coal keep changing all the time in uneven steps without any definite laws to govern it. That creates hard problems in the process of coal transportation, crushing and combustion. The next group of problems concerns operation and upgrading of the power generation equipment. That applies especially to the existing boilers which bum low-grade fuel in order to improve their operation in terms of higher thermal efficiency, controllability, reliability, improved environmental indices, etc. An increasingly high importance is attached to environmental impact problems incident to lignite coal utilisation. Abatement of sulphur oxide emissions and dust pollution is a problem solution of which cannot wait. The possibilities for partial solution of the environmental problems through increasing the thermal efficiency of facilities at the thermal Power

PHOSPHORUS FERTILIZATION AND HARVEST INTERVALS INFLUENCE ENERGETIC AND PHYSICAL PROPERTIES OF BRIQUETTES AND LARGE BRANCHES OF MATE

Directory of Open Access Journals (Sweden)

Delmar Santin

Full Text Available ABSTRACT In mate crop, the commercial part consists of leaves and thin branches, while the large branches (LB are considered unused residues and left in the field, although they may have potential for use as energy. The objective of this paper was to evaluate the influence of phosphorus fertilization and harvest interval in productivity of mate large branches and in their physical and energetic properties, as well as in derived briquettes. In a seven-year-old plantation, doses of 0, 20, 40, 80, 160 and 320 kg.ha-1 of P2O5 were applied considering harvest intervals of 12, 18 and 24 months. Dry mass, average diameter, P content, and physical and energetic properties of LB were determined. With LB, after its transformation into particles and briquetting, physical and energetic properties were determined, as well as P availability in soil. The phosphorus fertilization increased LB productivity in larger harvest intervals, increasing the amount of energy produced per unit of area, but did not change basic density and gross calorific value of wood. Mate harvest intervals did not affect the apparent density and calorific value of briquettes produced by LB. LB harvested at intervals of 18 and 24 months produced wood with higher basic density and gross calorific value. LB or briquettes have adequate energetic and physical properties, being technically a plant residue with great potential for use as energy.

Feminism and Society: Solidarity Amongst Pakistani Women Still a Distant Dream

Directory of Open Access Journals (Sweden)

Dr. Farhat Jabeen

2013-06-01

Patriarchal structure of society, socio-customary practices and discrimination against women are very serious concerns/issues which need to be understood as multidimensional problem. This paper examines the role of feminism on gender development in south Asian perspective especially in Pakistan. Pakistani women seem to have been circumscribed in bounds of religious, cultural and national ideologies as envisioned by the patriarchy of Pakistan. Due to certain cultural, male domination state of affairs the solidarity amongst Pakistani women still distant dream. Current research paper would draw attention to issue mentioned above.

Inequalities in health: a comparative study between ethnic Norwegians and Pakistanis in Oslo, Norway

Directory of Open Access Journals (Sweden)

Claussen Bjorgulf

2006-06-01

Full Text Available Abstract Background The objective of the study was to observe the inequality in health from the perspective of socio-economic factors in relation to ethnic Pakistanis and ethnic Norwegians in Oslo, Norway. Method Data was collected by using an open and structured questionnaire, as a part of the Oslo Health Study 2000–2001. Accordingly 13581 ethnic Norwegians (45% of the eligible participated as against 339 ethnic Pakistanis (38% of the eligible. Results The ethnic Pakistanis reported a higher prevalence of poor self-rated health 54.7% as opposed to 22.1% (p Conclusion There is a large diversity of self-rated health, prevalence of diabetes and distress among the ethnic Pakistanis and Norwegians. Socio-economic status may partly explain the observed inequalities in health. Uncontrolled variables like genetics, lifestyle factors and psychosocial factors related to migration such as social support, community participation, discrimination, and integration may have contributed to the observed phenomenon. This may underline the importance of a multidisciplinary approach in future studies.

Catalysts for cleaner combustion of coal, wood and briquettes sulfur dioxide reduction options for low emission sources

Energy Technology Data Exchange (ETDEWEB)

Smith, P.V. [Global Environmental Solutions, Inc., Morton Grove, IL (United States)

1995-12-31

Coal fired, low emission sources are a major factor in the air quality problems facing eastern European cities. These sources include: stoker-fired boilers which feed district heating systems and also meet local industrial steam demand, hand-fired boilers which provide heat for one building or a small group of buildings, and masonary tile stoves which heat individual rooms. Global Environmental Systems is marketing through Global Environmental Systems of Polane, Inc. catalysts to improve the combustion of coal, wood or fuel oils in these combustion systems. PCCL-II Combustion Catalysts promotes more complete combustion, reduces or eliminates slag formations, soot, corrosion and some air pollution emissions and is especially effective on high sulfur-high vanadium residual oils. Glo-Klen is a semi-dry powder continuous acting catalyst that is injected directly into the furnace of boilers by operating personnel. It is a multi-purpose catalyst that is a furnace combustion catalyst that saves fuel by increasing combustion efficiency, a cleaner of heat transfer surfaces that saves additional fuel by increasing the absorption of heat, a corrosion-inhibiting catalyst that reduces costly corrosion damage and an air pollution reducing catalyst that reduces air pollution type stack emissions. The reduction of sulfur dioxides from coal or oil-fired boilers of the hand fired stoker design and larger, can be controlled by the induction of the Glo-Klen combustion catalyst and either hydrated lime or pulverized limestone.

British-Pakistani women's perspectives of diabetes self-management: the role of identity.

Science.gov (United States)

Majeed-Ariss, Rabiya; Jackson, Cath; Knapp, Peter; Cheater, Francine M

2015-09-01

To explore the effects of type 2 diabetes on British-Pakistani women's identity and its relationship with self-management. Type 2 diabetes is more prevalent and has worse outcomes among some ethnic minority groups. This may be due to poorer self-management and an inadequate match of health services to patient needs. The influence that type 2 diabetes has on British-Pakistani women's identity and subsequent self-management has received limited attention. An explorative qualitative study. Face-to-face semi-structured English and Urdu language interviews were conducted with a purposively selected heterogeneous sample of 15 British-Pakistani women with type 2 diabetes. Transcripts were analysed thematically. Four themes emerged: Perceived change in self emphasised how British-Pakistani women underwent a conscious adaptation of identity following diagnosis; Familiarity with ill health reflected women's adjustment to their changed identity over time; Diagnosis improves social support enabled women to accept changes within themselves and Supporting family is a barrier to self-management demonstrated how family roles were an aspect of women's identities that was resilient to change. The over-arching theme Role re-alignment enables successful self-management encapsulated how self-management was a continuous process where achievements needed to be sustained. Inter-generational differences were also noted: first generation women talked about challenges associated with ageing and co-morbidities; second generation women talked about familial and work roles competing with self-management. The complex nature of British-Pakistani women's self-identification requires consideration when planning and delivering healthcare. Culturally competent practice should recognise how generational status influences self-identity and diabetes self-management in ethnically diverse women. Health professionals should remain mindful of effective self-management occurring alongside, and being

Suicidal ideation in Pakistani college students.

Science.gov (United States)

Khokher, Sehar; Khan, Murad M

2005-01-01

Suicidal behavior includes ideation, attempts and completed suicides. Information on suicidal behavior from Pakistan, a conservative South Asian Islamic country, is lacking. To address the issue, a pilot study was carried out to assess the prevalence of suicidal ideation in Pakistani college students. Suicidal ideation was assessed on the basis of responses to four questions contained in the depression subscale of the General Health Questionnaire-28. Of the total 217 completed questionnaires, the overall rate of suicidal ideation was 31.4%. While there was no significant difference between genders, more females (33%) than males (29.2%) responded positively. Respondents belonging to single parent families and those living at home, compared to those using hostel facilities, reported higher rates. The reported rate in our sample is higher than similar studies conducted elsewhere. There is the need for more information in this important area of suicidal behavior, including studying such feelings in school going children as well as in a larger community sample. The findings of such studies can contribute to our understanding of the suicidal process in the Pakistani population and to address it at various levels.

Pakistani and Bangladeshi Young Men: Re-Racialization, Class and Masculinity within the Neo-Liberal School

Science.gov (United States)

Mac an Ghaill, Mairtin; Haywood, Chris

2014-01-01

This article explores Pakistani and Bangladeshi young men's experiences of schooling to examine what inclusion/exclusion means to them. Qualitative research was undertaken with 48 Pakistani and Bangladeshi young men living in areas of the West Midlands, England. The young men highlighted three key areas: the emergence of a schooling regime…

Content of arsenic, selenium, mercury in the coal, food, clay and drinking water on the Zhaotong fluorosis area, eastern Yunnan Province

Energy Technology Data Exchange (ETDEWEB)

Luo Kun-li; Li Hui-jie; Chen Tong-bin (and others) [Chinese Academy of Sciences, Beijing (China). Institute of Geographic Sciences and Natural Resources Research

2008-03-15

About 160 samples of coal, corn, capsicum and drinking water were collected from the endemic fluorosis area of Zhenxiong and Weixin County, Zhaotong City of Yunnan Province, to determine the arsenic (As), selenium (Se) and mercury (Hg) content by AAF-800. The study found that the As content in the main coal seam from the Late Permian coal mines in Zhaotong City is 8.84 mg/kg and some civil coal can reach 89.09 mg/kg. The Se and Hg in the coal samples of Late Permian is lower, but Se and Hg are more concentrated in the pyritic coal balls and the pyritic gangue of the coal seam. The As content in corn and capsicum dried by coal-burning is more than 0.7 mg/kg, the natural standard amount of arsenic content permitted in food by China. The Se and Hg content in corn dried by coal-burning is lower than the natural standard of Se and Hg content in food in China but the Se and Hg content of capsicum dried by coal-burning exceeds the amount permitted by the natural standard for food in China. Clay, used as an additive for the coal-burning process and as a binder in making briquettes, contains a high content of As, generally more than 16 mg/kg. However, the Se and Hg content of clay itself are low. The As, Se and Hg content of drinking water are lower than the natural standard of As, Se and Hg content in the drinking water. So, there is high-As content coal and high-As content dried corn and capsicum in the endemic fluorosis area of Zhaotong City of Yunnan Province. The high As content of the dried corn and capsicum might have originated from the high arsenic content of burnt coal and clay. 30 refs., 4 tabs.

Family, Socialization and Migration in Norwegian-Pakistani Families: A Study of the First and the Second Generation

OpenAIRE

Shakari, Yasmine

2013-01-01

Summary Author s name: Yasmine Shakari Title: Family, Socialization and Migration in Norwegian-Pakistani Families: A Study of the First and the Second Generation Supervisor: Øystein Gullvåg Holter Co-supervisor: Thomas Walle Aim of study: This thesis seeks to obtain knowledge about 1) how the first generation of Norwegian-Pakistanis were raised in Pakistan in terms of socialization of gender roles, 2) how the second generation of Norwegian-Pakistanis have been raised here in Norway, and 3) if...

Factors causing stress among Pakistani working women

Directory of Open Access Journals (Sweden)

Ahmed Arif

2017-09-01

Full Text Available Women are traditionally considered to be confined within the four walls of their houses in the developing countries. They are still unable to play an active role in the development of society. They are striving to make their identity as an integral part of the society. Being a member of conservative developing society, women are still facing many hindrances, causing stressful situation for them, which prohibits them to participate actively in the economic development. This paper attempts to explore the critical factors creating stress among Pakistani working women. Based on literature review, the key stressors were identified to be as work life balance, gender discrimination, peers behaviour, lack of promotional opportunities and sexual harassment. These factors were found to be creating physiological, behavioural and psychological problems. The target of this study was the women working in secretarial and administrative positions in Pakistani organisations. Regression analysis was conducted to find out the impact of these stressors on working women. The results revealed that sexual harassment, peers behaviour and lack of promotional opportunities were the most dominant stressors.

Fundamental study on carbon composite iron ore hot briquette used as blast furnace burden

Energy Technology Data Exchange (ETDEWEB)

Chu, Man-sheng; Liu, Zheng-gen; Wang, Zhao-cai [Institute of Ferrous Metallurgy, Northeastern University, Shenyang (China); Yagi, Jun-ichiro [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University (Japan)

2011-05-15

Carbon composite iron ore hot briquette (CCB) is the product of fine iron ore and fine coal by hot briquetting process, which attracts more and more attention as a new type of ironmaking raw materials aiming to improve the operation efficiency and reduce the coke consumption of blast furnace. This paper is devoted to experimental study on metallurgical properties of CCB and numerical simulation of the BF operation with CCB charging. At first, the metallurgical properties of CCB, including cold crushing strength, RDI, RSI, reducibility, high temperature strength, and softening and dripping are experimentally tested and compared with the common burdens, which revealed that the CCB possesses the required metallurgical properties and is suitable to use as the blast furnace burden. Then, the effects of charging CCB on the dripping properties of comprehensive burdens are elucidated based on the experiments under simulated blast furnace conditions. The results showed that the maximum charging ratio of CCB in the iron burdens is 40%-50% for achieving appropriate dripping properties of the mixed burdens. Finally, a multi-fluid blast furnace model is used to simulate BF operation with CCB charging. According to model simulations, charging CCB will cause the temperature level to decreases in the furnace and the location of the cohesive zone shifts downward. On the other hand, the productivity tends to increase while coke rate and total reducing agent rate decrease, the heat efficiency improves remarkably and the operation performance of BF is effectively enhanced. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Fuel for domestic and metallurgical uses

Energy Technology Data Exchange (ETDEWEB)

Basu, D.; Chakrabarti, R.K.

1981-02-01

To meet the energy requirements in the domestic and metallurgical sectors CMPDI have taken in hand some developmental projects using coal as a feedback. 4 projects are described - mechanized conversion of coal to domestic coke, formed coke making by Didier-Keihan-Sumitomo process, domestic briquette making based on non-copking coal resources, and smokeless coal blocks utilising inferior grade raw coal and washery by-products.

Genetic analysis of a consanguineous Pakistani family with Leber ...

Indian Academy of Sciences (India)

2014-08-01

Aug 1, 2014 ... RESEARCH NOTE. Genetic analysis of a consanguineous Pakistani family with Leber .... representation of the deleterious mutation at genomic and protein level. ... In the last couple of years, numerous mutations in. GUCY2D ...

The Effects of Immigration and Media Influence on Body Image Among Pakistani Men

OpenAIRE

Saghir, Sheeba; Hyland, Lynda

2017-01-01

This study examined the role of media influence and immigration on body image among Pakistani men. Attitudes toward the body were compared between those living in Pakistan (n = 56) and those who had immigrated to the United Arab Emirates (n = 58). Results of a factorial analysis of variance demonstrated a significant main effect of immigrant status. Pakistani men living in the United Arab Emirates displayed poorer body image than those in the Pakistan sample. Results also indicated a second m...

Cerebral Palsy in Pakistani Children: A Hospital Based Survey

Directory of Open Access Journals (Sweden)

Atif Ahmed Khan

2014-08-01

Conclusion:Spastic quadriplegia or spastic diplegia are the commonest presentations in Pakistani children diagnosed with CP. The frequent etiological factors in CP development are birth asphyxia, prematurity, meningoencephalitis and kernicterus. [Cukurova Med J 2014; 39(4.000: 705-711

Domestic fuel consumption in Estonia (The first half of 1993)

International Nuclear Information System (INIS)

Veski, Rein

1993-01-01

According to the data of the Estonian Statistics Department the consumption of fuels in Estonia over the period of January-June 1993 was a follows: coal 77,053 t, oil shale 7,981,840 t, fuel peat 127,376 t, peat briquette 42,041 t, firewood 154,511 solid metres, wood chip 55,648 solid metres. The consumption of fuel peat (chiefly for producing briquette) was more considerable in the town of Kohtla-Jaerve and in the districts of Paernu and Tartu where Estonia's major peat-briquette plants are located. The share of peat in the other industries has been less significant. (author)

PAKISTANIS IN ITALY: THE DISENCHANTMENTS OF “LIVING TRANSNATIONALLY”

Directory of Open Access Journals (Sweden)

Ali Nobil Ahmad

2010-12-01

Full Text Available This article begins with a constructive critique of theories on immigration and highlights the problems implicit in the suppositions of the social network/capital theory and in research on ethnic economies and “transnationalism”. From these theories, the author adopts the postulates that he considers to be most useful for applying to the analysis of the Pakistani diaspora in Italy, demystifying the old theories and calling for greater focus on the economic policy of the networks of emigrants that actually exist. He believes that diasporas act as organisms that are linked in space and time, and which progressively mutate. He goes on to observe how the relatively weak links that today’s emigrants maintain with their country of origin contrast with the undoubtedly stronger links that previous generations of Pakistani emigrants maintained in the United Kingdom; thus he suggests that we should break the reductionist chain of association that automatically attributes greater levels of transnationalism to the new emigration. In this respect, Nobil Ahmad notes that political and economic factors are sometimes more important than technology when it comes to shaping the intensity of the connections sustained between the issuing and welcoming societies in the migration process. Pakistanis in Italy have spent most of their energy working or standing up for their political rights in Europe rather than travelling or sending money home. Likewise, he notes that it is not always true that social networks necessarily carry out the function of mediation of emigration and reducing its costs; on the contrary, in the Mediterranean, the prominence of agenti in emigration networks suggests that we should be sensitive to the importance of mercantilised networks and to the commercial transactions between emigrants and autochthonous citizens. Finally, he calls attention to the individual experience of immigrants who have thrived businesswise, and whose experiences

HLA Dr beta 1 alleles in Pakistani patients with rheumatoid arthritis

International Nuclear Information System (INIS)

Naqi, N.; Ahmed, T.A.; Bashir, M.M.

2011-01-01

Objective: To determine frequencies of HLA DR beta 1 alleles in rheumatoid arthritis in Pakistani patients. Study Design: Cross sectional / analytical study. Place and Duration of Study: Department of Immunology, Armed Forces Institute of Pathology, Rawalpindi in collaboration with Rheumatology departments of Military Hospital, Rawalpindi and Fauji Foundation Hospital, Rawalpindi, from January 2009 to January 2010. Methodology: HLA DR beta 1 genotyping of one hundred Pakistani patients, diagnosed as having RA as per American College of Rheumatology revised criteria 1987, was done. HLA DR beta 1 genotyping was carried out at allele group level (DR beta 1*01-DR beta 1*16) by sequence specific primers in RA patients. Comparison of HLA DR beta 1 allele frequencies between patients and control groups was made using Pearson's chi-square test to find possible association of HLA DR?1 alleles with RA in Pakistani rheumatoid patients. Results: HLA DR beta 1*04 was expressed with significantly increased frequency in patients with rheumatoid arthritis (p <0.05). HLA DR?1*11 was expressed statistically significantly more in control group as compared to rheumatoid patients indicating a possible protective effect. There was no statistically significant difference observed in frequencies of HLA DR beta 1 allele *01, DR beta 1 allele *03, DR beta 1 allele *07, DR beta 1 allele *08, DR beta 1 allele *09, DR beta 1 allele *10, DR beta 1 allele *12, DR beta 1 allele *13, DR beta 1 allele *14, DR?1 allele *15 and DR beta 1 allele *16 between patients and control groups. Conclusion: The identification of susceptible HLA DR beta 1 alleles in Pakistani RA patients may help physicians to make early decisions regarding initiation of early intensive therapy with disease modifying anti rheumatic medicines and biological agents decreasing disability in RA patients. (author)

Genetic diversity of Pakistani maize genotypes using chromosome ...

African Journals Online (AJOL)

For improvement of maize crop presence of genetic diversity in the germplasm is very important. This study was conducted to determine genetic diversity among 17 Pakistani maize genotypes using 10 simple sequence repeat (SSR) primer sets. All the amplification products were in the range of <250-750 bp. To estimate the ...

Testing the Week Form Efficiency of Pakistani Stock Market (2000-2010

Directory of Open Access Journals (Sweden)

Abdul Haque

2011-01-01

Full Text Available This empirical paper tests out the weak form efficiency of Pakistani stock market by examining the weekly index over the period . Return series has a leptokurtic and negatively skewed distribution, which is away from normal distribution as reflected by significant Jarque-Bera statistic. Estimated results of ADF (1979, PP (1988 and KPSS (1992 tests, Ljung-Box Q-Statistic of autocorrelations and runs test of randomness reject the Random Walk Hypothesis (RWH for the returns series. Moreover the results of variance ratio test (Lo and MacKinlay (1988 also reject the RWH and prove the robustness of other estimated results. The rejection of RWH reveals that the Pakistani stock prices are not Weak Form Efficient.

Variables of briquetting process and quality of forestry biomass briquettes Variáveis do processo de briquetagem e qualidade de briquetes de biomassa florestal

Directory of Open Access Journals (Sweden)

Thielly Schmidt Furtado

2010-10-01

Full Text Available

In the quest for recovery of waste generated from forest production to the process of industrial transformation of the biomass it was developed the process of briquetting. The cluster of wood particles facilitates the operations of handling of combustible material in addition to concentrating the available energy in terms of volume. The purpose of this study was to evaluate whether the raw material affects the quality of the briquette and verify the effect of pressure applied during the mechanical and energy  characteristics of the final product, and to evaluate the behavior of the material mix (MIX compared to pure materials. The briquettes were produced in a pilot  briquetter, hydraulic piston, 120 °C with a constant pressure of 50 bar for eight minutes and 65, 95 or
130 bar for two minutes. Six briquettes were used for each treatment. The characteristics evaluated were calorific value (GCV, bulk density and compressive strength. The raw material has a greater influence on the quality of briquettes than the compaction pressure. The low pressure is the most suitable for Pinus sp forest biomass briquettes. In this, MIX submitted satisfactory quality of briquettes with PCS 4,773 kcal kg-1, density 1220 kg m-³ and compressive strength of 167 kgf cm-2.

doi: 10.4336/2010.pfb.30.62.101

Inhalation Exposure to PM-Bound Polycyclic Aromatic Hydrocarbons Released from Barbecue Grills Powered by Gas, Lump Charcoal, and Charcoal Briquettes.

Science.gov (United States)

Badyda, Artur J; Widziewicz, Kamila; Rogula-Kozłowska, Wioletta; Majewski, Grzegorz; Jureczko, Izabela

2018-01-01

The present study seeks to define the possible cancer risk arising from the inhalation exposure to particle (PM)-bound polycyclic aromatic hydrocarbons (PAHs) present in barbecue emission gases and to compare the risk depending on the type of fuel used for grill powering. Three types of fuel were compared: liquid propane gas, lump charcoal, and charcoal briquettes. PM 2.5 and PM 2.5-100 were collected during grilling. Subsequently, 16 PAHs congeners were extracted from the PM samples and measured quantitatively using gas chromatography. The content of PM-bound PAHs was used to calculate PAHs deposition in the respiratory tract using the multiple path particle dosimetry model. Finally, a probabilistic risk model was developed to assess the incremental lifetime cancer risk (ILCR) faced by people exposed to PAHs. We found a distinctly greater PAHs formation in case of grills powered by charcoal briquettes. The summary concentration of PAHs (Σ16PAH) ranged from inhale barbecue particles for 5 h a day, 40 days a year exceeds the acceptable level set by the U.S. Environmental Protection Agency. We conclude that the type of heat source used for grilling influences the PM-bound PAHs formation. The greatest concentration of PAHs is generated when grilling over charcoal briquettes. Loading grills with food generates conspicuously more PAHs emissions. Traditional grilling poses cancer risk much above the acceptable limit, as opposed to much less risk involving gas powered grills.

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

International Nuclear Information System (INIS)

Gug, JeongIn; Cacciola, David; Sobkowicz, Margaret J.

2015-01-01

Highlights: • Briquetting was used to produce solid fuels from municipal solid waste and recycled plastics. • Optimal drying, processing temperature and pressure were found to produce stable briquettes. • Addition of waste plastics yielded heating values comparable with typical coal feedstocks. • This processing method improves utilization of paper and plastic diverted from landfills. - Abstract: Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

Energy Technology Data Exchange (ETDEWEB)

Gug, JeongIn, E-mail: Jeongin_gug@student.uml.edu; Cacciola, David, E-mail: david_cacciola@student.uml.edu; Sobkowicz, Margaret J., E-mail: Margaret_sobkowiczkline@uml.edu

2015-01-15

Highlights: • Briquetting was used to produce solid fuels from municipal solid waste and recycled plastics. • Optimal drying, processing temperature and pressure were found to produce stable briquettes. • Addition of waste plastics yielded heating values comparable with typical coal feedstocks. • This processing method improves utilization of paper and plastic diverted from landfills. - Abstract: Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in

Entrepreneurial Attributes among Postgraduate Students of a Pakistani University

Science.gov (United States)

Ali, Akhtar; Topping, Keith J.; Tariq, Riaz H.

2010-01-01

This paper explores entrepreneurial attributes among the students of The Islamia University of Bahawalpur, a public sector Pakistani university. Multistage sampling was employed to maximize the representation. Five hundred and twenty one master's level students from thirty departments returned completed questionnaires. Three factors emerged: self…

Different sex ratios of children born to Indian and Pakistani immigrants in Norway

Directory of Open Access Journals (Sweden)

Brekke Torkel

2010-08-01

Full Text Available Abstract Background A low female-to-male ratio has been observed in different Asian countries, but this phenomenon has not been well studied among immigrants living in Western societies. In this study, we investigated whether a low female-to-male ratio exists among Indian and Pakistani immigrants living in Norway. In particular, we investigated whether the determination of sex via ultrasound examination, a common obstetric procedure that has been used in Norway since the early 1980 s, has influenced the female-to-male ratio among children born to parents of Indian or Pakistani origin. Methods We performed a retrospective cohort study of live births in mothers of Indian (n = 1597 and Pakistani (n = 5617 origin. Data were obtained from "Statistics Norway" and the female-to-male (F/M sex ratio was evaluated among 21,325 children born, in increasing birth order, during three stratified periods (i.e., 1969-1986, 1987-1996, and 1997-2005. Results A significant low female-to-male sex ratio was observed among children in the third and fourth birth order (sex ratio 65; 95% CI 51-80 from mothers of Indian origin who gave birth after 1987. Sex ratios did not deviate from the expected natural variation in the Indian cohort from 1969 to 1986, and remained stable in the Pakistani cohort during the entire study period. However, the female-to-male sex ratio seemed less skewed in recent years (i.e., 1997-2005. Conclusion Significant differences were observed in the sex ratio of children born to mothers of Indian origin compared with children born to mothers of Pakistani origin. A skewed number of female births among higher birth orders (i.e., third or later may partly reflect an increase in sex-selective abortion among mothers of Indian origin, although the numbers are too small to draw firm conclusions. Further research is needed to explain the observed differences in the female-to-male ratio among members of these ethnic groups who reside in Norway.

Optimization of binder addition and particle size for densification of coffee husks briquettes using response surface methodology

Science.gov (United States)

Raudah; Zulkifli

2018-03-01

The present research focuses on establishing the optimum conditions in converting coffee husk into a densified biomass fuel using starch as a binding agent. A Response Surface Methodology (RSM) approach using Box-Behnken experimental design with three levels (-1, 0, and +1) was employed to obtain the optimum level for each parameter. The briquettes wereproduced by compressing the mixture of coffee husk-starch in a piston and die assembly with the pressure of 2000 psi. Furthermore, starch percentage, pyrolysis time, and particle size were the input parameters for the algorithm. Bomb calorimeter was used to determine the heating value (HHV) of the solid fuel. The result of the study indicated that a combination of 34.71 mesh particle size, 110.93 min pyrolysis time, and 8% starch concentration werethe optimum variables.The HHV and density of the fuel were up to 5644.66 calgr-1 and 0.7069 grcm-3,respectively. The study showed that further research should be conducted to improve the briquette density therefore the coffee husk could be convert into commercialsolid fuel to replace the dependent on fossil fuel.

Pakistani women's use of mental health services and the role of social networks: a systematic review of quantitative and qualitative research.

Science.gov (United States)

Kapadia, Dharmi; Brooks, Helen Louise; Nazroo, James; Tranmer, Mark

2017-07-01

Pakistani women in the UK are an at-risk group with high levels of mental health problems, but low levels of mental health service use. However, the rates of service use for Pakistani women are unclear, partly because research with South Asian women has been incorrectly generalised to Pakistani women. Further, this research has been largely undertaken within an individualistic paradigm, with little consideration of patients' social networks, and how these may drive decisions to seek help. This systematic review aimed to clarify usage rates, and describe the nature of Pakistani women's social networks and how they may influence mental health service use. Ten journal databases (ASSIA, CINAHL Plus, EMBASE, HMIC, IBSS, MEDLINE, PsycINFO, Social Sciences Abstracts, Social Science Citation Index and Sociological Abstracts) and six sources of grey literature were searched for studies published between 1960 and the end of March 2014. Twenty-one studies met inclusion criteria. Ten studies (quantitative) reported on inpatient or outpatient service use between ethnic groups. Seven studies (four quantitative, three qualitative) investigated the nature of social networks, and four studies (qualitative) commented on how social networks were involved in accessing mental health services. Pakistani women were less likely than white (British) women to use most specialist mental health services. No difference was found between Pakistani and white women for the consultation of general practitioners for mental health problems. Pakistani women's networks displayed high levels of stigmatising attitudes towards mental health problems and mental health services, which acted as a deterrent to seeking help. No studies were found which compared stigma in networks between Pakistani women and women of other ethnic groups. Pakistani women are at a considerable disadvantage in gaining access to and using statutory mental health services, compared with white women; this, in part, is due to

A prospective study of social difficulties, acculturation and persistent depression in Pakistani women living in the UK.

Science.gov (United States)

Chaudhry, N; Husain, N; Tomenson, B; Creed, F

2012-06-01

The reasons for the high prevalence of depressive disorders in women of Pakistani origin living in the UK are not clear. The aim of this study was to determine the relative importance of life events, chronic social difficulties and acculturation in a population-based sample of British Pakistani women. A cross-sectional and prospective cohort study of 18- to 65-year-old Pakistani women in UK was carried out. The Schedule for Clinical Assessment in Neuropsychiatry for diagnosis, the Life Events and Difficulties Schedule for social stress and an acculturation questionnaire were used. Depressive disorder at baseline was associated with older age, social isolation and marked difficulties involving health and close relationships. Depressive disorder at follow-up was associated with severity of depression at baseline, difficulties in close relationships and two aspects of acculturation, especially less acculturation in relation to use of the English language. Lack of acculturation, especially less familiarity with the English language, is an independent predictor of persistence of depression in Pakistani women in UK. This needs to be taken into consideration when planning treatment, which also needs to address the personal difficulties associated with persistent depression. The implication of this work is that women of Pakistani origin with depression should be encouraged to receive help in the use of English as one part of treatment that may prevent relapse.

Proceedings, volume 20, The Institute for Briquetting and Agglomeration, September 1987

Energy Technology Data Exchange (ETDEWEB)

Roth, D.L. (ed.)

1988-01-01

32 papers are presented covering aspects of briquetting, pelletizing and agglomeration of various materials, including coal, plastics, flue gas gypsum and fertilizers. Papers on coal included the start-up of the Petrofina coal briquetting plant (UK), coal and refuse agglomeration by extrusion, coal dust reduction, agglomeration of Brazilian coal fines, use of coal and briquetting in ancient Chinese metallurgy, cooking briquettes from lignites in developing nations, use of coal-dolomite pellets to eliminate sulphur emissions, extruded coal capsule flow characteristics, and oil agglomeration as a catalyst loading method in coal liquefaction.

GENDER ROLES IN PAKISTANI-URDU WEDDING SONGS

OpenAIRE

Syeda Bushra Zaidi

2016-01-01

This qualitative study of Pakistani-Urdu wedding songs allows a closer look at the gender situation, and towards the understanding of the process of construction and perpetuation of gender-based stereotypes. However, the major concern of this study is to understand the portrayal of each gender along with the question that does such portrayal underlines the traditional gender roles and gender inequality. Taking a discourse analysis perspective, this study analyzes textu...

Survival outcome of malignant minor salivary tumors in Pakistani population

Directory of Open Access Journals (Sweden)

Hassan Iqbal

2014-01-01

Full Text Available Objective: Malignant tumors of minor salivary glands (MSG are rare. Survival outcome in Pakistani population with malignant MSG tumors remains to be defined. The objective of this study was to report the clinical presentation, treatment modalities, and survival outcome of radically treated malignant tumors of MSG in Pakistani population. Materials and Methods: Between April 2003 and March 2011, 45 patients with malignant tumors of MSG were treated at Shaukat Khanum Cancer Hospital and included in the study. Patient characteristics and treatment modalities were assessed and local, regional, and distant failures determined. Relapse-free (RFS and overall survival (OS was calculated using Kaplan-Meier curves, and log-rank test was used to determine significance. Results: Median age was 40 (17-83 years. Male to female ratio was 1.25:1. Most common site was hard palate in 31 (69% patients. Adenoid cystic carcinoma (51% was the most common histological diagnosis. Nine patients (20% underwent surgery as the only treatment modality, six patients received (13% radiotherapy alone, and 30 patients (67% had surgery followed by adjuvant radiotherapy. Eight patients developed recurrence (four local, two regional, one locoregional, and one distant. The 5-year actuarial overall OS and RFS was 77 and 66%, respectively. Age, T-stage, and treatment modality were significant for RFS, whereas T-stage and treatment modality were significant factors for OS. Conclusion: Surgery as single modality or combined with radiation therapy resulted in acceptable survival in Pakistani population with malignant minor salivary tumors.

Pakistanis käib võitlus islamiriigi nimel / Karin Volmer

Index Scriptorium Estoniae

Volmer, Karin

2007-01-01

Pakistani pealinna Islamabadi Punase mošee ümber kestva, vähemalt 16 ohvrit nõudnud vastasseisu taga on islamiäärmuslaste soov kangutada ametist Ameerika-meelne president Pervez Musharraf. Vt. samas: Sündmused; Pakistan: kaart

Pakistanis living in Oslo have lower serum 1,25-dihydroxyvitamin D levels but higher serum ionized calcium levels compared with ethnic Norwegians. The Oslo Health Study

Science.gov (United States)

Holvik, Kristin; Meyer, Haakon E; Søgaard, Anne Johanne; Haug, Egil; Falch, Jan A

2007-01-01

Background Persons of Pakistani origin living in Oslo have a much higher prevalence of vitamin D deficiency and secondary hyperparathyroidism but similar bone mineral density compared with ethnic Norwegians. Our objective was to investigate whether Pakistani immigrants living in Oslo have an altered vitamin D metabolism by means of compensatory higher serum levels of 1,25-dihydroxyvitamin D (s-1,25(OH)2D) compared with ethnic Norwegians; and whether serum levels of ionized calcium (s-Ca2+) differ between Pakistanis and Norwegians. Methods In a cross-sectional, population-based study venous serum samples were drawn from 94 Pakistani men and 67 Pakistani women aged 30–60 years, and 290 Norwegian men and 270 Norwegian women aged 45–60 years; in total 721 subjects. Results Pakistanis had lower s-1,25(OH)2D compared with Norwegians (p Oslo with low vitamin D status and secondary hyperparathyroidism have lower s-1,25(OH)2D compared with ethnic Norwegians. However, the Pakistanis have higher s-Ca2+. The cause of the higher s-Ca2+ in Pakistanis in spite of their higher iPTH remains unclear. PMID:17945003

Assessment of Heavy Metal Content of Branded Pakistani Herbal ...

African Journals Online (AJOL)

Purpose: To investigate the heavy metals present in branded Pakistani herbal medicines used in the management of various human ailments. Method: The herbal dosage forms assessed were tablets, capsules and syrups. The samples were prepared for analysis by wet digestion method using nitric acid and perchloric acid ...

Waste Water Treatment-Bed of Coal Fly Ash for Dyes and Pigments Industry

Directory of Open Access Journals (Sweden)

Syed Farman Ali Shah

2015-12-01

Full Text Available The highly porous power plant waste ashes have been utilized to treat toxic effluent of a dyes manufacturing plant. An attempt has been made for the first time in Pakistan, to generate an effective and economically sound treatment facility for the toxic effluent of a dyes manufacturing plant. This is an indigenous bed which could replace expensive treatment facilities, such as reverse osmosis (RO, granulated activated carbon (GAC bed, etc. The treatment efficiency was improved by coupling coagulants with fly ash adsorbent bed. The ash was collected from coal fired boilers of power plant at Lakhra Power Generation Company, Jamshoro, Pakistan. The use of this ash resolved the disposal and environmental issues by treating wastewater of chemical, dyes and pigment industry. The treatment bed comprised of briquettes of coal fly ash coupled with commercial coagulant ferrous sulfate-lime reduced COD, color, turbidity and TSS of effluent remarkably. An adsorption capacity and chemical behavior of fly ash bed was also studied. In coagulation treatment, coagulant FeSO4-lime influenced reduction of COD, color, turbidity and TSS by 32%, 48%, 50% and 51%, respectively. The CFAB coupled with coagulant, resulted an excessive removal of color, TSS, COD, and turbidity by 88%, 92%, 67% and89%, respectively.

Waste Water Treatment-Bed of Coal Fly Ash for Dyes and Pigments Industry

International Nuclear Information System (INIS)

Shah, S.F.A.; Aftab, A.; Soomro, N.; Nawaz, M.S.; Vafai, K.

2015-01-01

The highly porous power plant waste ashes have been utilized to treat toxic effluent of a dyes manufacturing plant. An attempt has been made for the first time in Pakistan, to generate an effective and economically sound treatment facility for the toxic effluent of a dyes manufacturing plant. This is an indigenous bed which could replace expensive treatment facilities, such as reverse osmosis (RO), granulated activated carbon (GAC) bed, etc. The treatment efficiency was improved by coupling coagulants with fly ash adsorbent bed. The ash was collected from coal fired boilers of power plant at Lakhra Power Generation Company, Jamshoro, Pakistan. The use of this ash resolved the disposal and environmental issues by treating wastewater of chemical, dyes and pigment industry. The treatment bed comprised of briquettes of coal fly ash coupled with commercial coagulant ferrous sulfate-lime reduced COD, color, turbidity and TSS of effluent remarkably. An adsorption capacity and chemical behavior of fly ash bed was also studied. In coagulation treatment, coagulant FeSO/sun 4/-lime influenced reduction of COD, color, turbidity and TSS by 32 percentage, 48 percentage, 50 percentage and 51 percentage, respectively. The CFAB coupled with coagulant, resulted an excessive removal of color, TSS, COD, and turbidity by 88 percentage, 92 percentage, 67 percentage and 89 percentage, respectively. (author)

A Quantitative Study of Empathy in Pakistani Medical Students: A Multicentered Approach.

Science.gov (United States)

Tariq, Nabia; Rasheed, Tariq; Tavakol, Mohsen

2017-10-01

To examine the empathy level of undergraduate medical students in Pakistan. Three hypotheses are developed based on the literature review. (1) Female medical students have a higher level of empathy than do male students. (2) Empathy scores vary during the medical school years in Pakistani students. (3) Medical students interested in people-oriented specialties would score higher than the students interested in technology-oriented specialties. This is a quantitative inquiry approach using a cross-sectional design of 1453 students from 8 Pakistani medical schools, both private and state. The sample consists of 41.1% (n = 597) male students and 58.9% (n = 856) female students. Empirical data are collected using the Jefferson Scale of Physician Empathy (JSPE), a well-validated self-administered questionnaire. The mean empathy score among students is 4.77 with a standard deviation of 0.72. The results show that there is no statistically significant association between the empathy scores and gender, t(1342.36) = -0.053, P = .95). There is a statistically significant difference between the empathy scores and the years of medical school, F(14, 1448) = 4.95, P = .01. Concerning the specialty interests, there is no statistically significant difference between the empathy score and specialty interests. The findings of this study showed that in Western countries, medical students performed better than Pakistani medical students on the empathy scale. This finding has important implications for Pakistani medical educators to improve the interpersonal skills of medical students in the context of patient care. Inconsistent with our expectations and experiences, our findings do not support that female medical students scored better than their male counterparts on the empathy scale. Because of the nature of a cross-sectional study, it is impossible to argue the decline of empathy during medical school training.

Effects of reduction temperature to Ni and Fe content and the morphology of agglomerate of reduced laterite limonitic nickel ore by coal-bed method

Science.gov (United States)

Abdul, Fakhreza; Pintowantoro, Sungging; Kawigraha, Adji; Nursidiq, Ahlidin

2018-04-01

As the current drop of nickel sulfide ore on earth, the attention to nickel laterite ore processing was inscreased in order to fulfill the future nickel demand needs. This research aims to optimized the process of nickel laterite ore extraction using coal bed method. This research was conducted by reducing low grade nickel laterite ore (limonitic) with nickel content of 1.25 %. The reduction process was carried out using CO gas which formed by the reaction of coal and dolomite. The Briquette of nickel ore, coal, Na2SO4 mixtures incorporated in the crucible with bed, then reduced for 6 hours at the temperature of 1200 °C. 1400 °C, and 1400 °C. The result of the research shown that the highest increase of Ni content and Ni recovery value was in the reduction temperature of 1400 °C with the increase of 3.44 %, and the recovery value of Ni equal to 86.75 %. While the highest increase of Fe content and Fe recovery value, respectively, was in the reduction temperature of 1300 °C with the increase of 22.67 % and 1200 °C with Fe recovery value of 89.41 %.

Genetic heterogeneity in Pakistani microcephaly families

DEFF Research Database (Denmark)

Sajid Hussain, M; Bakhtiar, Syeda Marriam; Farooq, Muhammad

2013-01-01

Autosomal recessive primary microcephaly (MCPH) is caused by mutations in at least eight different genes involved either in cell division or DNA repair. Most mutations are identified in consanguine families from Pakistan, Iran and India. To further assess their genetic heterogeneity and mutational...... mutation. One third of the families were linked to ASPM followed by WDR62 confirming previous data. We identified three novel ASPM mutations, four novel WDR62 mutations, one novel MCPH1 mutation and two novel CEP152 mutations. CEP152 mutations have not been described before in the Pakistani population....

Production and characterization of self-reducing briquettes to be used as metallic charge at Companhia Siderurgica de Tubarao; Producao e caracterizacao de briquetes auto-redutores a serem utilizados como carga metalica na Companhia Siderurgica de Tubarao

Energy Technology Data Exchange (ETDEWEB)

Gama Bentes, Marcos A. da [Companhia Siderurgica de Tubarao (CST), Serra, ES (Brazil); Resende, Caio S.; D`Abreu, Jose C. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Ciencia dos Materiais e Metalurgia

1996-12-31

The present work investigates the initial steps for characterization and production of self-reducing briquettes to be manufactured from a mixture of residues, which are generated in the various industrial processes at Companhia Siderurgica de Tubarao. The main development consists of three main stages, encompassing the development and production of self-reducing briquette and the investigation of its reduction in both solid and liquid phases. The produced briquette can be used as an alternative metallic and recarburizing raw material to be charged in the converters, or substituting the cooling scrap added in the steel ladles. Furthermore, this material can be eventually be applied to the new developed technologies for iron and steel production. The results of briquetting agglomeration studies of various mixtures containing iron and carbon rich materials are presented, as well the metallization rates, which were obtained in the gas-solid reduction furnaces for the briquettes of different residue compositions. Finally, the liquid phase experiments to be carried out in a vacuum induction furnace are discussed. (author) 9 refs., 15 figs., 3 tabs.

Brand equity in the Pakistani hotel industry

OpenAIRE

Ishaq, Muhammad Ishtiaq; Hussain, Nazia; Asim, Ali Ijaz; Cheema, Luqman J.

2014-01-01

Brand equity is considered as the most important aspect of branding, which is a set of brands' assets and liabilities, its symbol or name that subtracts from or adds the value provided by a product or service to a firm and customers. The current research endeavor was to identify the interrelationship of customer-based brand equity dimensions (brand awareness, brand loyalty, brand image, and service quality) in Pakistani hotel industry. Data was collected from 821 consumers who experienced the...

Identities in the third space? Solidity, elasticity and resilience amongst young British Pakistani Muslims.

Science.gov (United States)

Mythen, Gabe

2012-09-01

Over the last decade the issue of identity has been prevalent in discussions about British Muslims, with the events of 9/11 serving as a touchstone for media debates about religious, national and cultural affiliations. The 7/7 terrorist attacks in the UK led to young British Pakistanis being subjected to intense public and institutional scrutiny and wider political concerns being expressed about the failure of multiculturalism. Young British Pakistanis have thus had to negotiate and maintain their identities in an environment in which they have been defined as a threat to national security whilst simultaneously being pressurized to align with 'core British values'. Within this context, we convey the findings of a qualitative study involving British Pakistanis living in the North-west of England. In presenting the experiences and perspectives of participants, three interconnected processes salient to the maintenance of identity are delineated: solidity, elasticity and resilience. Having unpacked these processes, we draw upon Bhabha's third space thesis to explore the political potentiality of and the limits to hybridic identities. © London School of Economics and Political Science 2012.

A comparison of antenatal classifications of 'overweight' and 'obesity' prevalence between white British, Indian, Pakistani and Bangladeshi pregnant women in England; analysis of retrospective data.

Science.gov (United States)

Garcia, Rebecca; Ali, Nasreen; Guppy, Andy; Griffiths, Malcolm; Randhawa, Gurch

2017-04-11

Maternal obesity increases women's risk of poor birth outcomes, and statistics show that Pakistani and Bangladeshi women (who are born or settled) in the UK experience higher rates of perinatal mortality and congenital anomalies than white British or white Other women. This study compares the prevalence of maternal obesity in Indian, Pakistani, Bangladeshi and white British women using standard and Asian-specific BMI metrics. Retrospective cross-sectional analysis using routinely recorded secondary data in Ciconia Maternity information System (CMiS), between 2008 and 2013. Mothers (n = 15,205) whose ethnicity was recorded as white British, Bangladeshi, Pakistani or Indian. Adjusted standardised residuals and Pearson Chi-square. Percentage of mothers stratified by ethnicity (Indian, Pakistani, Bangladeshi and white British) who are classified as overweight or obese using standard and revised World Health Organisation BMI thresholds. Compared to standard BMI thresholds, using the revised BMI threshold resulted in a higher prevalence of obesity: 22.8% of Indian and 24.3% of Bangladeshi and 32.3% of Pakistani women. Pearson Chi-square confirmed that significantly more Pakistani women were classified as 'obese' compared with white British, Indian or Bangladeshi women (χ 2  = 499,88 df = 9, p women stratified by maternal ethnicity of white British, Indian, Pakistani and Bangladeshi. Using revised anthropometric measures in Indian, Pakistani and Bangladeshi women has clinical implications for identifying risks associated with obesity and increased complications in pregnancy.

Breast cancer histology and receptor status characterization in Asian Indian and Pakistani women in the U.S. - a SEER analysis

International Nuclear Information System (INIS)

Kakarala, Madhuri; Rozek, Laura; Cote, Michele; Liyanage, Samadhi; Brenner, Dean E

2010-01-01

Recent reports suggest increase in estrogen receptor (ER), progesterone receptor (PR) negative breast cancer yet little is known about histology or receptor status of breast cancer in Indian/Pakistani women.in the U.S. We examined the United States National Cancer Institute's Surveillance Epidemiology and End Results (SEER) Cancer program to assess: a) frequency of breast cancer by age, b) histologic subtypes, c) receptor status of breast cancer and, d) survival in Indians/Pakistanis compared to Caucasians. There were 360,933 breast cancer cases diagnosed 1988-2006. Chi-Square analyses and Cox proportional hazards models, to estimate relative risks for breast cancer mortality after adjusting for confounders, were performed using Statistical Analysis Software 9.2. Among Asian Indian/Pakistani breast cancer patients, 16.2% were < 40 yrs. old compared to 6.23% in Caucasians (p < 0.0001). Asian Indian women had more invasive ductal carcinoma (69.1 vs. 65.7%, p < 0.0001), inflammatory cancer (1.4% vs. 0.8, p < 0.0001) and less invasive lobular carcinoma (4.2% vs. 8.1%, p < 0.0001) than Caucasians. Asian Indian/Pakistani women had more ER/PR negative breast cancer (30.6% vs. 21.8%, p = 0.0095) than Caucasians. Adjusting for stage at diagnosis, age, tumor grade, nodal status, and histology, Asian Indian/Pakistani women's survival was similar to Caucasians, while African Americans' was worse. Asian Indian/Pakistani women have higher frequency of breast cancer (particularly in age < 40), ER/PR negative invasive ductal and inflammatory cancer than Caucasians

Moringa oleifera: a promising agricultural crop and of social inclusion for Brazil and semi-arid regions for the production of energetic biomass (biodiesel and briquettes

Directory of Open Access Journals (Sweden)

Pereira Francisco Sávio Gomes

2018-01-01

Full Text Available This study describes properties of biomasses of Moringa oleifera Lamarck for energetic applications of production of biodiesel and briquettes. The seeds collected of the mature pods were the initial biomasses used of this plant. The seeds were separated into husks and oilseed grains, from which the oils were extracted by mechanical pressing and by solvent extraction. The crude oil mixed (of pressing and by solvent was degummed, neutralized, washed, dried and characterized. The purified oil was converted into methyl biodiesel in homogeneous alkaline transesterification, which was purified and characterized. The residual peels and pies had their calorific powers measured and compared with classic agricultural residues: firewood, sugarcane bagasse and coconut husks. Moringa culture was compared to soybeans in agricultural and biodiesel production perspectives. The analytical results show that the biomasses of the moringa are favorable as renewable biofuels like biodiesel or briquettes due to the good calorific power and simple and accessible productive technology. The production of briquettes starting from the biomasses of the moringa would be recommended with the uses of the pod husks, seed peels and pies (cakes of extraction of the oil. The agricultural management and the simple productive technologies applied to the moringa are favorable for social inclusion by enabling family agriculture.

Psychosocial factors and distress: a comparison between ethnic Norwegians and ethnic Pakistanis in Oslo, Norway.

Science.gov (United States)

Syed, Hammad Raza; Dalgard, Odd Steffen; Dalen, Ingvild; Claussen, Bjørgulf; Hussain, Akthar; Selmer, Randi; Ahlberg, Nora

2006-07-10

In the Norwegian context, higher mental distress has been reported for the non-Western immigrants compared to the ethnic Norwegians and Western immigrants. This high level of distress is often related to different socio-economic conditions in this group. No efforts have been made earlier to observe the impact of changed psychosocial conditions on the state of mental distress of these immigrant communities due to the migration process. Therefore, the objective of the study was to investigate the association between psychological distress and psychosocial factors among Pakistani immigrants and ethnic Norwegians in Oslo, and to investigate to what extent differences in mental health could be explained by psychosocial and socioeconomic conditions. Data was collected from questionnaires as a part of the Oslo Health Study 2000-2001. 13581 Norwegian born (attendance rate 46%) and 339 ethnic Pakistanis (attendance rate 38%) in the selected age groups participated. A 10-item version of Hopkins Symptom Checklist (HSCL) was used as a measure of psychological distress. Pakistanis reported less education and lower employment rate than Norwegians (p < 0.005). The Pakistani immigrants also reported higher distress, mean HSCL score 1.53(1.48-1.59), compared to the ethnic Norwegians, HSCL score 1.30(1.29-1.30). The groups differed significantly (p < 0.005) with respect to social support and feeling of powerlessness, the Pakistanis reporting less support and more powerlessness. The expected difference in mean distress was reduced from 0.23 (0.19-0.29) to 0.07 (0.01-0.12) and 0.12 (0.07-0.18) when adjusted for socioeconomic and social support variables respectively. Adjusting for all these variables simultaneously, the difference in the distress level between the two groups was eliminated Poor social support and economic conditions are important mediators of mental health among immigrants. The public health recommendations/interventions should deal with both the economic conditions

Alternative coke production from unconventional feedstocks

Energy Technology Data Exchange (ETDEWEB)

Smoot, D.; Eatough, C.N.; Heaton, J.S.; Eatough, S.R.; Miller, A.B. [Combustion Resources, Provo, UT (US)

2004-07-01

This presentation reports on US Department of Energy and company sponsored research and development to develop a technology and process for making metallurgical-quality coke from alternate feedstocks, including by-product and waste carbonaceous materials. The basic patent-pending process blends and presses these carbon-containing materials into briquettes of specified size. This product is referred to as CR Clean Coke because pollutant emission levels are carefully controlled to low levels with little or no vagrant emissions during processing. A wide range of feedstock materials has been investigated in over 600 tests for run-of-mine and waste coal fines of various rank with blends of coal tars and pitches, coal and biomass chars, met-coke breeze or petroleum coke. For various coal/pet-coke/tar feedstocks, CR has produced uniform-sized briquettes in commercial-scale briquettes in three nominal sizes: one inch, two inch, and three inch. These products have been successfully qualified according to stringent requirements for conventional met-coke use in a blast furnace. Several formulation have met and frequently exceeded these established met-coke specifications. One specific product containing coal, tar and pet-coke was selected as a base formulation for which preliminary process design and cost estimates have been completed for construction and operation of a demonstration plant capable of producing 120,000 tons per year of CR Clean Coke. Plant design elements and blast furnace test plans are presented. Tailoring of CR Clean Coke products to other prospective end users including foundry, sugar, soda ash, and ferrometals industries presents additional opportunities. The text is accompanied by 30 slides/overheads. 14 refs., 3 figs., 9 tabs.

Pyrolysis of corn stalk biomass briquettes in a scaled-up microwave technology.

Science.gov (United States)

Salema, Arshad Adam; Afzal, Muhammad T; Bennamoun, Lyes

2017-06-01

Pyrolysis of corn stalk biomass briquettes was carried out in a developed microwave (MW) reactor supplied with 2.45GHz frequency using 3kW power generator. MW power and biomass loading were the key parameters investigated in this study. Highest bio-oil, biochar, and gas yield of 19.6%, 41.1%, and 54.0% was achieved at different process condition. In terms of quality, biochar exhibited good heating value (32MJ/kg) than bio-oil (2.47MJ/kg). Bio-oil was also characterised chemically using FTIR and GC-MS method. This work may open new dimension towards development of large-scale MW pyrolysis technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of Organic Binders on The Quality of Manganese Ore Sinter Fines Briquettes

International Nuclear Information System (INIS)

Mohamed, F. M.; Ahmed, Y.M.Z.; Shalabi, M. E. H.

2004-01-01

Sinai Manganese Company imports the manganese ore sinter from abroad for ferromanganese alloy production. Large quantities of manganese ore sinter fines are produced in this process. These fines must be agglomerated to a suitable size in order to be reused for charging the electric arc furnace. The aim of this work is studying the briquetting ability of these fines using organic binders such as starch and bitumen. The results showed that, the suitable briquettes were produced with the addition of 5 % of starch and 20% H 2 O under pressure 3 ton/cm 2 or 8 % bitumen under pressure 4 ton/cm 2 and 3 days curing time

When I raised my head again : feminism and the female body in Bapsi Sidhwa’s novels The Pakistani bride and Cracking India

OpenAIRE

Marwah, Ane Frislid Sveinhaug

2008-01-01

This thesis sets out to do close readings of the Pakistani author Bapsi Sidhwa’s novels The Pakistani Bride and Cracking India. It sheds light on the ways in which the image of the female body is used in the two novels and in what ways this image represents the novels’ feminist message. The close readings reveal many similarities between the novels’ treatment of the female body, but also interesting developments that take place in Sidhwa’s feminism from The Pakistani Bride of the 1970s to Cra...

Evolution of Systemic Hypertension in Pakistani Population

International Nuclear Information System (INIS)

Aziz, K. U.

2015-01-01

The prevalence of essential hypertension is alarmingly increasing in Pakistani population inspite of the demographics being of lower BMI and nutrition. In this review, the possible factors responsible for this increase are identified by reviewing the population studies conducted in Pakistan. The prevalence rate is about 3 - 4% in childhood and steeply rises near the middle age. The factors peculiar to Pakistan were increased genetic susceptibility, environmental factors such as gender, females gender, urbanization, obesity and sedentary life styles particularly in middle age, cultural practices promoting sedentary life style in female. (author)

Social and cultural construction of obesity among Pakistani Muslim women in North West England.

Science.gov (United States)

Ludwig, Alison F; Cox, Peter; Ellahi, Basma

2011-10-01

The present qualitative study explored health perceptions, diet and the social construction of obesity and how this relates to the initiation and maintenance of a healthier diet in UK Pakistani women. Pakistani women in Greater Manchester participated in focus group and one-to-one discussions. Semi-structured interviews employing fictional vignettes and body shape images were used to explore the participants' beliefs and practices regarding diet, overweight/obesity and the risk of type 2 diabetes. Transcripts were analysed using phenomenological and sociological approaches. Interviews took place either in local community and Pakistani resource centres or in private homes. First- and second-generation women who were both active in the community and housebound. The women spoke English and/or Urdu. The fifty-five participants lacked the motivation to address weight gain and were unsure how to do so. There was a limited awareness of the link between weight gain and type 2 diabetes. Other barriers included the influence of Islam, culture and familial expectations on home cooking, perceptions that weight gain is inevitable (owing to ageing, childbirth or divine predestination) and the prioritisation of family concerns over individual lifestyle changes. As the findings of the present research did not correspond to existing educational and behaviour change models, a new Health Action Transition conceptual model is proposed. Health education programmes that aim to address obesity and its associated risks in the South Asian community must take into account the complex beliefs and practices and the multiple dimensions of religion, ethnic and social identity within this population. The present study provides further insight into these factors and proposes a novel model for use in designing and implementing education interventions for British Pakistani women.

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics.

Science.gov (United States)

Gug, JeongIn; Cacciola, David; Sobkowicz, Margaret J

2015-01-01

Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in higher heating value. Analysis of the post-processing water uptake and compressive strength showed a correlation between density and stability to both mechanical stress and humid environment. Proximate analysis indicated heating values comparable to coal. The results showed that mechanical and moisture uptake stability were improved when the moisture and air contents were optimized. Moreover, the briquette

Produção e avaliação de briquetes de resíduos lignocelulósicos Production and evaluation of lignocellulosic residue briquettes

Directory of Open Access Journals (Sweden)

Luana Elis de Ramos e Paula

2011-06-01

Full Text Available

O objetivo deste trabalho foi produzir e avaliar briquetes de resíduos de biomassa vegetal e testar diferentes tempos e temperaturas de briquetagem para alguns deles. O material utilizado foi resíduos do processamento da madeira (maravalha e serragem; pergaminho do grão e caule do cafeeiro; caule e vagem do feijão; caule e vagem da soja; casca de arroz; folha, caule, palha e sabugo de milho e palha e bagaço de cana-de-açúcar. A briquetagem foi realizada à pressão de 150 Bar. Foram testados diferentes tempos de briquetagem para a serragem da madeira e diferentes temperaturas para a casca do arroz e para o pergaminho do café. Na avaliação da qualidade dos briquetes, determinaram-se a densidade relativa aparente, a resistência à compressão e o índice de combustão. Os resultados indicaram que o tempo e a temperatura de briquetagem interferiram na resistência mecânica dos briquetes. O melhor tempo de prensagem foi de 8 minutos e a temperatura de 125 °C. Os briquetes da casca de arroz apresentaram maior densidade e alta resistência mecânica. O maior índice de combustão foi encontrado para os briquetes da vagem do feijão.

doi: 10.4336/2011.pfb.31.66.103

This study aimed to produce and evaluating the briquettes made from residues of plant biomass and test different times and temperatures. The material utilized was composed of wood processing residues (wood shaving and sawdust, coffee bean parchment and coffee tree stem, beam stem and pod, soybean stem and pod, rice husk, corn leaf, stem, straw and cob and sugar cane straw and bagasse. Briquetting was performed at a pressure of 150 Bar. Different times were tested for briquetting sawdust from wood and different temperatures for rice husk and parchment coffee. For evaluation of the briquettes quality, the apparent relative density, compression resistance and combustion index were determined. The results

A comparison of antenatal classifications of ‘overweight’ and ‘obesity’ prevalence between white British, Indian, Pakistani and Bangladeshi pregnant women in England; analysis of retrospective data

Directory of Open Access Journals (Sweden)

Rebecca Garcia

2017-04-01

Full Text Available Abstract Background Maternal obesity increases women’s risk of poor birth outcomes, and statistics show that Pakistani and Bangladeshi women (who are born or settled in the UK experience higher rates of perinatal mortality and congenital anomalies than white British or white Other women. This study compares the prevalence of maternal obesity in Indian, Pakistani, Bangladeshi and white British women using standard and Asian-specific BMI metrics. Method Retrospective cross-sectional analysis using routinely recorded secondary data in Ciconia Maternity information System (CMiS, between 2008 and 2013. Mothers (n = 15,205 whose ethnicity was recorded as white British, Bangladeshi, Pakistani or Indian. Adjusted standardised residuals and Pearson Chi-square. Main outcome measures: Percentage of mothers stratified by ethnicity (Indian, Pakistani, Bangladeshi and white British who are classified as overweight or obese using standard and revised World Health Organisation BMI thresholds. Results Compared to standard BMI thresholds, using the revised BMI threshold resulted in a higher prevalence of obesity: 22.8% of Indian and 24.3% of Bangladeshi and 32.3% of Pakistani women. Pearson Chi-square confirmed that significantly more Pakistani women were classified as ‘obese’ compared with white British, Indian or Bangladeshi women (χ 2  = 499,88 df = 9, p < 0.001. Conclusions There are differences in the prevalence of obese and overweight women stratified by maternal ethnicity of white British, Indian, Pakistani and Bangladeshi. Using revised anthropometric measures in Indian, Pakistani and Bangladeshi women has clinical implications for identifying risks associated with obesity and increased complications in pregnancy.

Continuing Bonds in Bereaved Pakistani Muslims: Effects of Culture and Religion

Science.gov (United States)

Suhail, Kausar; Jamil, Naila; Oyebode, Jan; Ajmal, Mohammad Asir

2011-01-01

This study explores the bereavement process and continuing bond in Pakistani Muslims with the focus on how culture and religion influence these processes. Ten participants were interviewed and their transcribed interviews were analyzed using a grounded theory approach. Three main domains were identified from the narratives expressed by the…

Comparison of general health status, myocardial infarction, obesity, diabetes, and fruit and vegetable intake between immigrant Pakistani population in the Netherlands and the local Amsterdam population.

Science.gov (United States)

Raza, Qaisar; Nicolaou, Mary; Dijkshoorn, Henriëtte; Seidell, Jacob C

2017-12-01

South Asians living in Western countries have shown higher prevalence of cardiovascular disease and related non-communicable diseases as compared to the local populations. The aim of this study was to compare the general health status and prevalence of myocardial infarction (MI), diabetes, high blood pressure, overweight, obesity, and fruit and vegetable intake between Pakistani immigrants in the Netherlands and local Amsterdam population. A health survey was conducted in 2012-2013 among Pakistanis in the Netherlands. Results were compared with a health survey conducted among inhabitants of Amsterdam in 2012. One hundred and fifty-four Pakistanis from four big cities of the Netherlands and 7218 inhabitants of Amsterdam participated. The data for Amsterdam population were weighed on the basis of age, gender, city district, marital status, ethnicity and income level while the data for Pakistanis were weighed on the basis of age and gender to make both data-sets representative of their general population. Pakistanis reported a high prevalence of MI (3.3%), diabetes (11.4%), high blood pressure (14.4%), overweight (35.5%) and obesity (18.5%) while Amsterdam population reported the prevalence as 2.5% for MI, 6.8% for diabetes, 15.3% for high blood pressure, 28.1% for overweight and 11.1% for obesity. Pakistanis had a significantly higher level of MI (OR = 2.71; 95% CI: 1.19-6.14), diabetes (OR = 4.41; 95% CI: 2.66-7.33) and obesity (OR = 2.51; 95% CI: 1.53-4.12) after controlling for age, sex and educational level with Amsterdam population as the reference group. Pakistanis showed a higher intake of fruit and fruit juice as compared to Amsterdam population though the latter showed a higher intake of cooked vegetables. Higher prevalence of MI, diabetes and obesity among Pakistanis than Amsterdam population indicates the need for health scientists and policy-makers to develop interventions for tackling non-communicable diseases and its determinants among

Evaluation of the potential energy briquettes made with corn stubble (Zea mays) and soybean residue (Glycine max (L.)) combined with waste wood; Avaliacao do potencial energetico de briquetes confeccionados com residuo de milho (Zea mays) e residuo de soja (Glycine max (L.)) combinado com residuo de madeira

Energy Technology Data Exchange (ETDEWEB)

Travessini, Rosana; Schutz, Fabiana Costa de Araujo; Oyama, Paulo; Possan, Edna; Bittencourt, Paulo R.S. [Universidade Tecnologica Federal do Parana (UTFPR), Medianeira, PR (Brazil)], emails: rosana_travessini@yahoo.com.br, fabianaschutz@utfpr.edu.br, oyama_pt@hotmail.com, epossan@gmail.com, paulob@utfpr.edu.br

2011-07-01

The agriculture industry produces a large amount of biomass whose use constitutes an economically viable alternative energy through the compression of the lignocellulosic portion, replacing the wood with an equivalent product. This is possible through the briquette, which is a very efficient way to concentrate the available energy in biomass. This study aimed to evaluate the efficiency of burning briquettes. The making of briquettes was performed in the laboratory of Electro mechanics and burning at the Laboratory of Environmental UTFPR Campus Medianeira / PR. For the analysis, the energy balance of the combinations we used a bomb calorimeter IKA C5000, Laboratory of Biomass Energy (LEB), Federal University of Parana - UFPR. From the results we can conclude that in all aspects of the briquettes made from soybean residues are more efficient and still points to the need for studies to the development of more efficient equipment for these specific applications. (author)

PROSPECTS FOR COKE BREEZE RECOVERY

Directory of Open Access Journals (Sweden)

D. N. Mihnovets

2012-01-01

Full Text Available Researches give grounds to believe in the possibility of receiving briquettes from coke waste mixed with peat dry coal and their use for smelting iron in the cupola or as a household fuel.

Gender Discrimination in Death Reportage: Reconnoitering Disparities through a Comparative Analysis of Male and Female Paid Obituaries of Pakistani English Newspapers

Science.gov (United States)

Chaudhry, Sajid M.; Christopher, Anne A.; Krishnasamy, Hariharan A/L N.

2014-01-01

The study examines the issue of gender discrimination in the post death scenario of obituarial discourse. It aims to identify the way Pakistani newspaper obituaries recognize and project males and females after their deaths. A total of 601 paid obituaries published in a year's time span in Pakistani English newspapers were evaluated for the…

Energy from briquettes produced from remains of urban solid residues and wood of Eucalyptus grandis; Energia de briquetes produzidos com rejeitos de residuos solidos urbanos e madeira de Eucalyptus grandis

Energy Technology Data Exchange (ETDEWEB)

Goncalves, Jose E.; Leao, Alcides L. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Botucatu, SP (Brazil). Dept. de Ciencias Ambientais], emails: evaristo@fca.unesp.br, alcidesleao@fca.unesp.br; Sartori, Maria M.P. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Bauru, SP (Brazil). Dept. de Engenharia de Producao], email: msartori@btu.flash.tv.br

2009-07-01

The incentive for consumption and production in large quantity in modern society generates enormous amounts of urban solid residues in the form of municipal solid waste (MSW). With the intention of reducing these residues of the municipal waste tips and to generate energy, briquettes with mixtures of MSW and residues of Eucalyptus grandis were produced. The briquettes were manufactured with 0, 5, 10, 15, 20 and 25% of MSW in the mixture with wood waste and 12% of moisture content. The analyzed parameters used to choose the best treatments were combustion analysis versus ash content, mechanical strength and energy content. The briquettes up to 10% of MSW showed low resistance, and above 15% showed large increase in ash content. Therefore, the treatment that fulfilled the requirements for combustion versus ash content and mechanical resistance was of at least 15% of MSW, since the source of the ash is unidentified. Considering the net energy content, the best treatment was 25% of MSW, with 17,175 kJ kg{sup -1}. Nevertheless, it is strongly advised that further studies related to gas emissions are necessary. (author)

Molecular and Clinical Studies of X-linked Deafness Among Pakistani Families

Science.gov (United States)

Waryah, Ali M.; Ahmed, Zubair M.; Choo, Daniel I.; Sisk, Robert A.; Binder, Munir A.; Shahzad, Mohsin; Khan, Shaheen N.; Friedman, Thomas B.; Riazuddin, Sheikh; Riazuddin, Saima

2011-01-01

There are 68 sex-linked syndromes that include hearing loss as one feature and five sex-linked nonsyndromic deafness loci listed in the OMIM database. The possibility of additional such sex-linked loci was explored by ascertaining three unrelated Pakistani families (PKDF536, PKDF1132, PKDF740) segregating X-linked recessive deafness. Sequence analysis of POU3F4 (DFN3) in affected members of families PKDF536 and PKDF1132 revealed two novel nonsense mutations, p.Q136X and p.W114X, respectively. Family PKDF740 is segregating congenital blindness, mild to profound progressive hearing loss that is characteristic of Norrie disease (MIM#310600). Sequence analysis of NDP among affected members of this family revealed a novel single nucleotide deletion c.49delG causing a frameshift and premature truncation (p.V17fsX1) of the encoded protein. These mutations were not found in 150 normal DNA samples. Identification of pathogenic alleles causing X-linked recessive deafness will improve molecular diagnosis, genetic counseling, and molecular epidemiology of hearing loss among Pakistanis. PMID:21633365

Molecular and clinical studies of X-linked deafness among Pakistani families.

Science.gov (United States)

Waryah, Ali M; Ahmed, Zubair M; Bhinder, Munir A; Binder, Munir A; Choo, Daniel I; Sisk, Robert A; Shahzad, Mohsin; Khan, Shaheen N; Friedman, Thomas B; Riazuddin, Sheikh; Riazuddin, Saima

2011-07-01

There are 68 sex-linked syndromes that include hearing loss as one feature and five sex-linked nonsyndromic deafness loci listed in the OMIM database. The possibility of additional such sex-linked loci was explored by ascertaining three unrelated Pakistani families (PKDF536, PKDF1132 and PKDF740) segregating X-linked recessive deafness. Sequence analysis of POU3F4 (DFN3) in affected members of families PKDF536 and PKDF1132 revealed two novel nonsense mutations, p.Q136X and p.W114X, respectively. Family PKDF740 is segregating congenital blindness, mild-to-profound progressive hearing loss that is characteristic of Norrie disease (MIM#310600). Sequence analysis of NDP among affected members of this family revealed a novel single nucleotide deletion c.49delG causing a frameshift and premature truncation (p.V17fsX1) of the encoded protein. These mutations were not found in 150 normal DNA samples. Identification of pathogenic alleles causing X-linked recessive deafness will improve molecular diagnosis, genetic counseling and molecular epidemiology of hearing loss among Pakistanis.

Fiscal 2000 survey report on rationalization project for international energy conservation. Preparation of master plan for rational energy consumption (Shanxi Province, China); 2000 nendo kokuasi energy shiyo gorika kiban seibi jigyo chosa hokokusho. Goriteki energy shiyo no tame no master plan sakusei (Chugoku Shanxi sho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A comprehensive master plan for Shanxi Province was prepared jointly with China for the purpose of promoting rational use of energy and realizing an environmentally harmonious demand/supply structure of energy. This paper describes the fiscal 2000 results. The first phase refers to the surmounting of environmental problems incident to the use of coal and the restoration of regional economy. As countermeasures against air pollution in Taiyuan City, environmental measures were propagated such as simplified flue-gas desulfurization in thermal power plants, energy conservation in coke dry quenching, etc., and desulfurization of coke oven gas. Bio-briquette effective against smoke and soot pollution was carried out, as was general rubbish treatment (e.g., compost and coal/rubbish mixed combustion power generation). Promoted, by the opening of a clean coal center, were sulfur content reduction, coal briquette method, market expansion for CWM, etc. Producing city gas out of coal mine methane gas was also among the ideas considered. With the aim of attaining a Shanxi Province zero emission program, incentives are essential and, for this purpose, support by the national government is desirable including subsidies for investment, low-interest loans, tax deductions/exemptions, and yen-denominated loans from Japan. The second phase is intended for harmony with culture/science/nature, control of global warming and advanced utilization of coal. (NEDO)

Social gradients in health for Pakistani and White British women and infants in two UK birth cohorts.

Science.gov (United States)

Uphoff, Eleonora P; Pickett, Kate E; Wright, John

2016-10-01

This study aims to examine social gradients in low birth weight (LBW), preterm birth, smoking during pregnancy and maternal health for women and infants of Pakistani origin and White British women and infants in the UK. The sample included women and singleton infants from the Born in Bradford (BiB) study (n = 8181) and the first sweep of the Millennium Cohort Study (MCS) (n = 8980). Social gradients in health for four measures of socioeconomic status (SES): maternal education, means-tested benefits, financial situation, and occupation of the father were analysed in multivariate regression models adjusting for maternal age and parity. For White British mothers and infants in the MCS sample, social gradients in health were observed for at least three out of four measures of SES for each health outcome (p for trend social gradient in health for Pakistani women was demonstrated with the self-reported measure of financial situation, in relation to mental health (p for trend social gradients in health for Pakistani women and infants and discusses potential explanations for this finding.

Coal background paper. Coal demand

International Nuclear Information System (INIS)

1997-01-01

Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

Reducibility study of Rossetta ilmenite ore briquettes and powder with coke breeze at 800-1100°C

Directory of Open Access Journals (Sweden)

Abd el Gawad Hala H.

2013-01-01

Full Text Available Ilmenite ore fine and coke breeze as reduced material were briquetted with different amounts of organic materials such as molasses or pitch were studied in this investigation. The produced briquettes at reasonable condition were reduced in nitrogen atmosphere at temperature range 800 - 1100oC to determine the factors controlling the reduction and to determine the controlling mechanism. Also ilmenite ore fine with coke breeze were reduced at the same temperature range in nitrogen atmosphere without briquetting process, for the sake of comparison.

In silico analysis of a disease-causing mutation in PCDH15 gene in a consanguineous Pakistani family with Usher phenotype

OpenAIRE

Shamim Saleha; Muhammad Ajmal; Muhammad Jamil

2016-01-01

AIM: To map Usher phenotype in a consanguineous Pakistani family and identify disease-associated mutation in a causative gene to establish phenotype-genotype correlation. METHODS: A consanguineous Pakistani family in which Usher phenotype was segregating as an autosomal recessive trait was ascertained. On the basis of results of clinical investigations of affected members of this family disease was diagnosed as Usher syndrome (USH). To identify the locus responsible for the Usher phenotype...

Identification of rust resistance genes Lr10 and Sr9a in Pakistani ...

African Journals Online (AJOL)

Identification of rust resistance genes Lr10 and Sr9a in Pakistani wheat germplasm using PCR based molecular markers. M Babar, AF Mashhadi, A Mehvish, AN Zahra, R Waheed, A Hasnain, S ur-Rahman, N Hussain, M Ali, I Khaliq, A Aziz ...

Epidemiology, major risk factors and genetic predisposition for breast cancer in the Pakistani population.

Science.gov (United States)

Shaukat, Uzma; Ismail, Muhammad; Mehmood, Nasir

2013-01-01

Occurrence of breast cancer is related to genetic as well as cultural, environmental and life-style factors. Variations in diversity of these factors among different ethnic groups and geographical areas emphasize the immense need for studies in all racial-ethnic populations. The incidence of breast cancer in Pakistan is highest in Asians after Jews in Israel and 2.5 times higher than that in neighboring countries like Iran and India, accounting for 34.6% of female cancers. The Pakistani population is deficient in information regarding breast cancer etiology and epidemiology, but efforts done so far had suggested consanguinity as a major risk factor for frequent mutations leading to breast cancer and has also shed light on genetic origins in different ethnic groups within Pakistan. World-wide research efforts on different ethnicities have enhanced our understanding of genetic predisposition to breast cancer but despite these discoveries, 75% of the familial risk of breast cancer remains unexplained, highlighting the fact that the majority of breast cancer susceptibility genes remain unidentified. For this purpose Pakistani population provides a strong genetic pool to elucidate the genetic etiology of breast cancer because of cousin marriages. In this review, we describe the known breast cancer predisposition factors found in the local Pakistani population and the epidemiological research work done to emphasize the importance of exploring factors/variants contributing to breast cance, in order to prevent, cure and decrease its incidence in our country.

Psychosocial factors and distress: a comparison between ethnic Norwegians and ethnic Pakistanis in Oslo, Norway

Directory of Open Access Journals (Sweden)

Hussain Akthar

2006-07-01

Full Text Available Abstract Background In the Norwegian context, higher mental distress has been reported for the non-Western immigrants compared to the ethnic Norwegians and Western immigrants. This high level of distress is often related to different socio-economic conditions in this group. No efforts have been made earlier to observe the impact of changed psychosocial conditions on the state of mental distress of these immigrant communities due to the migration process. Therefore, the objective of the study was to investigate the association between psychological distress and psychosocial factors among Pakistani immigrants and ethnic Norwegians in Oslo, and to investigate to what extent differences in mental health could be explained by psychosocial and socioeconomic conditions. Method Data was collected from questionnaires as a part of the Oslo Health Study 2000–2001. 13581 Norwegian born (attendance rate 46% and 339 ethnic Pakistanis (attendance rate 38% in the selected age groups participated. A 10-item version of Hopkins Symptom Checklist (HSCL was used as a measure of psychological distress. Results Pakistanis reported less education and lower employment rate than Norwegians (p Conclusion Poor social support and economic conditions are important mediators of mental health among immigrants. The public health recommendations/interventions should deal with both the economic conditions and social support system of immigrant communities simultaneously.

Pakistani English Newspaper Paid Obituary Announcements: A Descriptive Analysis of the Transliterated Vocabulary

Science.gov (United States)

Chaudhry, Sajid M.; Christopher, Anne A.; Krishnasamy, Hariharan A/L N.

2016-01-01

The study, qualitative and descriptive in nature, examines the use of transliteration in the paid Pakistani obituary announcements authored in the English language. Primarily, it identifies the frequently used transliterated vocabulary in these linguistic messages and reconnoiters the functional relationship that emerges in and between the textual…

Understanding the Influence of the Pakistani Government in South Asia

Science.gov (United States)

2010-11-01

boundaries . The earliest events confronting the newly formed Pakistani government emerged from the migration of Muslims into Pakistan. According...between the provinces in the East and West. This decision by the central government led to violence in Dhaka in East Pakistan, where the death of...sic] plan to murder the hostages by suicide explosion if any attempt was made to rescue them. In Mecca, Saudi Arabia, the holiest city in the Islamic

Factors Affecting job satisfaction of employees in Pakistani banking sector

OpenAIRE

Ahmed Imran, Hunjra; Muhammad Irfan, Chani; Sher, Aslam; Muhammad, Azam; Kashif-Ur, Rehman

2010-01-01

The job satisfaction has got tremendous attention in organizational research. The focus of this study is to determine the impact of various human resource management practices like job autonomy, team work environment and leadership behavior on job satisfaction. It also investigates the major determinants of job satisfaction in Pakistani banking sector. This study further evaluates the level of difference in job satisfaction among male and female employees. The sample of the study consisted of...

Feminism and Society: Solidarity Amongst Pakistani Women Still a Distant Dream

Directory of Open Access Journals (Sweden)

Dr. Farhat Jabeen

2013-06-01

Full Text Available This paper envisages feminism in a south Asian gender development particularly in Pakistan. Law is the manifestation of principles of justice, equity and good conscience. As’ Gender’ has been taken up in development policy and practices, have been created that have emphasized some aspects of feminist agendas, and pushed others out of the frame. Research paper gives an overview of women in Pakistan are victimized of gender biases begin from the very first institution home. They are facing challenges in claiming their rights of inheritance owing to customary practices, lacunae in the prevailing legal framework and procedure. Patriarchal structure of society, socio-customary practices and discrimination against women are very serious concerns/issues which need to be understood as multidimensional problem. This paper examines the role of feminism on gender development in south Asian perspective especially in Pakistan. Pakistani women seem to have been circumscribed in bounds of religious, cultural and national ideologies as envisioned by the patriarchy of Pakistan. Due to certain cultural, male domination state of affairs the solidarity amongst Pakistani women still distant dream. Current research paper would draw attention to issue mentioned above.

The Effects of Immigration and Media Influence on Body Image Among Pakistani Men.

Science.gov (United States)

Saghir, Sheeba; Hyland, Lynda

2017-07-01

This study examined the role of media influence and immigration on body image among Pakistani men. Attitudes toward the body were compared between those living in Pakistan ( n = 56) and those who had immigrated to the United Arab Emirates ( n = 58). Results of a factorial analysis of variance demonstrated a significant main effect of immigrant status. Pakistani men living in the United Arab Emirates displayed poorer body image than those in the Pakistan sample. Results also indicated a second main effect of media influence.Those highly influenced by the media displayed poorer body image. No interaction effect was observed between immigrant status and media influence on body image. These findings suggest that media influence and immigration are among important risk factors for the development of negative body image among non-Western men. Interventions designed to address the negative effects of the media and immigration may be effective at reducing body image disorders and other related health problems in this population.

Health-Related Quality of Life, Subjective Health Complaints, Psychological Distress and Coping in Pakistani Immigrant Women With and Without the Metabolic Syndrome : The InnvaDiab-DEPLAN Study on Pakistani Immigrant Women Living in Oslo, Norway.

Science.gov (United States)

Hjellset, Victoria Telle; Ihlebæk, Camilla M; Bjørge, Benedikte; Eriksen, Hege R; Høstmark, Arne T

2011-08-01

The increasingly high number of immigrants from South-East Asia with The Metabolic Syndrome (MetS) is an important challenge for the public health sector. Impaired glucose is essential in MetS. The blood glucose concentration is not only governed by diet and physical activity, but also by psychological distress which could contribute to the development of MetS. The aim of this study is to describe health-related quality of life, subjective health complaints (SHC), psychological distress, and coping in Pakistani immigrant women, with and without MetS. As a part of an randomized controlled intervention study in Oslo, Norway, female Pakistani immigrants (n = 198) answered questionnaires regarding health related quality of life, SHC, psychological distress, and coping. Blood variables were determined and a standardized oral glucose tolerance test was performed. The participants had a high score on SHC and psychological distress. About 40% of the participants had MetS, and this group showed significantly lower general health, lower physical function, and more bodily pain, than those without MetS. Those with MetS also had more SHC, depressive symptoms, higher levels of somatisation, and scored significantly lower on the coping strategy of active problem solving. Pakistani immigrant women seem to have a high prevalence of SHC and psychological distress, especially those with MetS.

Vitamin D Receptor Gene Polymorphisms Influence T1D Susceptibility among Pakistanis

Directory of Open Access Journals (Sweden)

Maryam Mukhtar

2017-01-01

Full Text Available Background. The vitamin D receptor (VDR gene regulates insulin secretion from the pancreas and acts as a mediator of the immune response through vitamin D. Polymorphism in VDR causes alterations in the functioning of vitamin D, leading to type 1 diabetes (T1D predisposition. The aim of the present study was to determine VDR gene polymorphism in association with T1D in Pakistanis. Methods. The association was evaluated by selecting rs2228570 (FokΙ, rs7975232 (ApaΙ, and rs731236 (TaqΙ polymorphic sites in 102 patients and 100 controls. Genotypes were identified by DNA sequencing and PCR-RFLP. Results. The allelic and genotypic frequencies of FokΙ and ApaI were significantly associated with T1D (p0.05. CCGC, CCGG, CCTC, and CCTG haplotypes were significantly associated with disease development (p<0.05. However, CTGG haplotype was protective towards T1D (p<0.01. Conclusion. VDR polymorphisms were identified as susceptible regions for T1D development in the Pakistani population.

Molecular genetic studies and delineation of the oculocutaneous albinism phenotype in the Pakistani population

Directory of Open Access Journals (Sweden)

Jaworek Thomas J

2012-06-01

Full Text Available Abstract Background Oculocutaneous albinism (OCA is caused by a group of genetically heterogeneous inherited defects that result in the loss of pigmentation in the eyes, skin and hair. Mutations in the TYR, OCA2, TYRP1 and SLC45A2 genes have been shown to cause isolated OCA. No comprehensive analysis has been conducted to study the spectrum of OCA alleles prevailing in Pakistani albino populations. Methods We enrolled 40 large Pakistani families and screened them for OCA genes and a candidate gene, SLC24A5. Protein function effects were evaluated using in silico prediction algorithms and ex vivo studies in human melanocytes. The effects of splice-site mutations were determined using an exon-trapping assay. Results Screening of the TYR gene revealed four known (p.Arg299His, p.Pro406Leu, p.Gly419Arg, p.Arg278* and three novel mutations (p.Pro21Leu, p.Cys35Arg, p.Tyr411His in ten families. Ex vivo studies revealed the retention of an EGFP-tagged mutant (p.Pro21Leu, p.Cys35Arg or p.Tyr411His tyrosinase in the endoplasmic reticulum (ER at 37°C, but a significant fraction of p.Cys35Arg and p.Tyr411His left the ER in cells grown at a permissive temperature (31°C. Three novel (p.Asp486Tyr, p.Leu527Arg, c.1045-15 T > G and two known mutations (p.Pro743Leu, p.Ala787Thr of OCA2 were found in fourteen families. Exon-trapping assays with a construct containing a novel c.1045-15 T > G mutation revealed an error in splicing. No mutation in TYRP1, SLC45A2, and SLC24A5 was found in the remaining 16 families. Clinical evaluation of the families segregating either TYR or OCA2 mutations showed nystagmus, photophobia, and loss of pigmentation in the skin or hair follicles. Most of the affected individuals had grayish-blue colored eyes. Conclusions Our results show that ten and fourteen families harbored mutations in the TYR and OCA2 genes, respectively. Our findings, along with the results of previous studies, indicate that the p.Cys35Arg, p.Arg278

The conditions for use of reed canary grass briquettes and chopped reed canary grass in small heating plants; Foerutsaettningar foer anvaendning av roerflensbriketter och hackad roerflen i mindre vaermecentraler

Energy Technology Data Exchange (ETDEWEB)

Paulrud, Susanne; Davidsson, Kent; Holmgren, Magnus A. (Swedish National Testing and Research Inst., Boraas (Sweden)); Hedman, Henry; Oehman, Rikard; Leffler, Joel (ETC, Piteaa (Sweden))

2010-09-15

The aim of this study was to test fuel blends of briquettes and chopped reed canary grass in three existing heating plants (50 kW - 500 kW) and elucidate the requirements for good performance and low emissions. In addition, the study investigated production of reed canary grass briquettes using a Polish screw press developed for straw. Some tests with a bale shredder were also undertaken. The screw press technique is of interest for reed canary grass because it is a simple technique, easy to handle, developed for small scale production, and for straw. The test with reed canary grass in this study showed that the technique worked well but that further adjustments and a longer test period are needed in order to achieve higher bulk density and mechanical strength. The test with chopped reed canary grass shows that a system with a forage harvester is slightly more effective than baling and cutting in a bale shredder. The study concluded that few existing heating plants of size 50 kW-1 MW that currently use wood fuels will be able to use reed canary grass without adjustment, conversion or replacement of the combustion equipment. Reed canary grass has 15-20 times higher ash content than wood briquettes and 2-3 times higher ash content than forest residue; the combustion equipment must be able to handle these properties. The boiler must be equipped with a continuously operating ashing system and it must be possible to move the ash bed mechanically. There is a risk of high content of unburned matter if the residence time in the boiler is too short, due to the structure and low bulk density of the reed canary grass ash. Using a blend of wood briquettes and reed canary briquettes results in lower ash content, but also affects the ash chemistry and tends to lower the initial ash fusion temperature compared to using 100 % reed canary grass. Blending chopped reed canary grass and wood chips in an existing small scale heating plant also requires measures to achieve an even fuel

Wall thickness of major coronary arteries in Pakistani population

International Nuclear Information System (INIS)

Ullah, Q.W.; Qamar, K.; Butt, S.A.; Butt, S.A.

2012-01-01

To measure the wall thickness of major coronary arteries in Pakistani population, through micrometry. Study design: An observational study. Place and duration of study: Combined Military Hospital Rawalpindi, Khyber Medical College Peshawar and District Headquarter Hospital, Rawalpindi, in collaboration with Departments of Anatomy and Pathology, Army Medical College Rawalpindi. The duration of study was six months with effect from September 2009 to March 2010. Material and methods: After incising pericardium, 1 mm long segments of major coronary arteries i.e. right coronary artery (RCA), left anterior descending artery (LAD) and left circumflex artery (LCX) were taken 1cm distal to their origin, from adult male cadavers of up to 40 years age. After processing for paraffin embedding, 5 mu m thick sections were prepared, mounted on glass slides and subsequently stained with Hematoxylin and Eosin (H and E) for routine histological study. Verhoeff's elastic stain was used to make the elastic lamina more prominent. Wall thickness for each section was measured through micrometry, circumferentially at eight different places along the planes at 45 deg. to each other and then their mean taken as a reading for the respective artery. Results: The total wall thickness of major coronary arteries and of the individual tunicae was less in Pakistani population. The mean thickness of RCA was 0.61 +- 0.05 mm; LAD had mean thickness of 0.55 +- 0.06 mm whereas that of LCX was 0.66 +- 0.13 mm. The mean thickness of tunica intima of RCA was noted to be 0.230 +- 0.044 mm; tunica media measured 0.205 +- 0.031 mm whereas tunica adventitia was 0.172 +- 0.023 mm thick. The mean thickness of tunica intima of LAD measured 0.156 +- 0.032 mm; tunica media was observed to be 0.224 +- 0.026 mm thick whereas the tunica adventitia was 0.170 +- 0.032 mm thick. The mean thickness of tunica intima of LCX was observed to be 0.203 +- 0.059 mm; tunica media to be 0.282 +- 0.097 mm whereas that of tunica

FY 1999 report on the potential survey of the environmentally friendly type coal utilization system - Dispatch of engineers. A. Project for supporting the introduction of the environmentally friendly type coal utilization system (model project)/pre-survey for the potential survey; 1999 nendo kankyo chowa gata sekitan riyo system kanosei chosa. Senmomka haken A. kankyo chowa gata sekitan riyo system donyu shien jigyo (model jigyo) - Kanosei chosa no jizen chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of the improvement of coal utilization technology and environmental preservation, the paper conducted the pre-survey of the introduction of coke oven gas desulfurization facilities in China and pre-survey of potentiality of the environmentally friendly type coal utilization system in India. The pre-survey in China was made for Anyang Steel Group Co. Ltd. and Laiwu Steel Group Co. Ltd. to judge their adaptability as site for the demonstrative project on the introduction of coke oven gas desulfurization facilities. As a result, it was confirmed that the former satisfied the conditions on Japan side such as the space for installation and prospect for fund raising. However, the amount of COG treatment was larger than that planned at Japan side, and it was found that as to the recovered sulfur, the company wanted the solid sulfur different from the fused sulfur planned at Japan side. In the survey in India, explanations were made to India of CFBC and the fluidized bed cement sintering system, bio-briquette production facilities, facilities for environmental measures, coal reforming technology, etc. At the same time, the site survey was made to examine/analyze possibilities of spread/development of Japan's CCT. (NEDO)

Economic statistics for the mining and metallurgical industries - 1978 and 1979

Energy Technology Data Exchange (ETDEWEB)

Medaets, J.

1982-04-01

The statistics are compiled in 5 sections : 1) The mining industries (coal, metallurgy, quarries and associated industries); 2) The manufacture of coke and briquettes; 3) Iron and steel; 4) Hydrology; and 5) The extraction of sand on Belgium's 'continental shelf'.

Is Pakistani Equity Market Integrated to the Equity Markets of Group of Eight (G8 Countries? An Empirical Analysis of Karachi Stock Exchange

Directory of Open Access Journals (Sweden)

Syed Muhammad Aamir Shah

2012-09-01

Full Text Available This study looks at the dynamic relationship between the Pakistani equity market and equity markets of Group of Eight countries (G8 which includes Canada, France, Germany, Italy, Japan, Russia, UK and USA by using weekly time series data starting from June 2004 to May 2009. Multivariate Co-integration approach by Johnson and Julius (1990 shows there exists no long-term relationship between the G8 and Pakistani equity market. Vector error correction (VECM model suggests that 100% of the lag periods disequilibrium has been corrected in the current period. Pairwise Granger Causality test shows that there exist a unidirectional causality between the equity market of Pakistan and the markets of France, Germany, Italy, Japan and United Kingdom. Impulse response analysis and variance decomposition analysis reveal that most of the shocks in Pakistani equity market are due to its own innovation and behave like exogenous. However, the markets of France, Japan, Germany and United Kingdom are exerting a little pressure on Pakistani equity markets. Therefore, by investing in Karachi Stock Exchange (KSE the fund manager of G8 countries especially Canada, Italy, Russia and USA is capable of getting the advantage of portfolio diversification.

Between Preferences: Marriage and Mobility among Danish Pakistani Youth

DEFF Research Database (Denmark)

Rytter, Mikkel

2012-01-01

and an increasing number of local love marriages have changed the overall picture. This article discusses how the new marriage preferences affect common notions of family relatedness, and suggest that young couples' decision to engage in a love marriage constitutes an act of symbolic mobility. Ultimately Danish...... Pakistanis are split between the marriage preferences set up by their families, the Danish nation-state and themselves. In this respect marriage is not only about entering adulthood and deciding one's future, but also constitutes a process where notions of identity and belonging are negotiated within local...

International Coal Report's coal year 1991

Energy Technology Data Exchange (ETDEWEB)

McCloskey, G [ed.

1991-05-31

Following introductory articles on factors affecting trade in coal and developments in the freight market, tables are given for coal exports and coal imports for major countries worldwide for 1989 and 1990. Figures are also included for coal consumption in Canada and the Eastern bloc,, power station consumption in Japan, coal supply and demand in the UK, electric utility coal consumption and stocks in the USA, coal production in Australia, Canada and USA by state, and world hard coal production. A final section gives electricity production and hard coal deliveries in the EEC, sales of imported and local coal and world production of pig iron and steel.

Clinical Presentation of Ulcerative Colitis in Pakistani Adults.

Science.gov (United States)

Qureshi, Mustafa; Abbas, Zaigham

2015-01-01

The aim of this study was to determine the clinical presentation and severity of ulcerative colitis (UC) in Pakistani adult patients. An observational study. Data were obtained by reviewing the medical records of patients who visited a gastroenterology clinic between 2008 and 2012. There were 54 patients diagnosed as UC. The male to female ratio was 1:1. Mean age at diagnosis of UC was 38.7 ± 11.8 years (median 36.5, range 18-64). The predominant presenting symptoms were mucus diarrhea in 49 (90.7%), gross blood in stools in 42 (77.8%), abdominal pain or cramps in 40 (74.1%) and weight loss in 15 (27.7%). Left-sided colitis was present in 23 (42.6%), pancolitis in 15 (27.8%), extensive colitis in 11 (20.4%), and proctitis in five (9.2%). The severity of UC as judged by the Mayo scoring system showed that 68.5% were suffering from moderate to severe disease while 31.5% had mild disease. The extra-intestinal manifestation were found only in seven patients; arthritis in five patients and anterior uveitis in two patients. The arthritis was unilateral and the sites were knee joint in three patients and sacroiliac joint in two patients. Ulcerative colitis presents in our adult patients may present at any age with no gender preponderance. The disease severity is moderate to severe in the majority of patients and more than half of them have left-sided colitis or pancolitis at the time of presentation. Extraintestinal manifestations were not common. Qureshi M, Abbas Z. Clinical Presentation of Ulcerative Colitis in Pakistani Adults. Euroasian J Hepato-Gastroenterol 2015;5(2):127-130.

Development of Growth Charts of Pakistani Children Aged 4-15 Years Using Quantile Regression: A Cross-sectional Study.

Science.gov (United States)

Iftikhar, Sundus; Khan, Nazeer; Siddiqui, Junaid S; Baig-Ansari, Naila

2018-02-02

Background Growth charts are essential tools used by pediatricians as well as public health researchers in assessing and monitoring the well-being of pediatric populations. Development of these growth charts, especially for children above five years of age, is challenging and requires current anthropometric data and advanced statistical analysis. These growth charts are generally presented as a series of smooth centile curves. A number of modeling approaches are available for generating growth charts and applying these on national datasets is important for generating country-specific reference growth charts. Objective To demonstrate that quantile regression (QR) as a viable statistical approach to construct growth reference charts and to assess the applicability of the World Health Organization (WHO) 2007 growth standards to a large Pakistani population of school-going children. Methodology This is a secondary data analysis using anthropometric data of 9,515 students from a Pakistani survey conducted between 2007 and 2014 in four cities of Pakistan. Growth reference charts were created using QR as well as the LMS (Box-Cox transformation (L), the median (M), and the generalized coefficient of variation (S)) method and then compared with WHO 2007 growth standards. Results Centile values estimated by the LMS method and QR procedure had few differences. The centile values attained from QR procedure of BMI-for-age, weight-for-age, and height-for-age of Pakistani children were lower than the standard WHO 2007 centile. Conclusion QR should be considered as an alternative method to develop growth charts for its simplicity and lack of necessity to transform data. WHO 2007 standards are not suitable for Pakistani children.

Assessment of Gender Dimorphism on Sagittal Cephalometry in Pakistani Population

International Nuclear Information System (INIS)

Qamruddin, I.; Shahid, F.; Tanveer, S.; Mukhtiar, M.; Asim, Z.; Alam, M. K.

2016-01-01

Objective: To determine and compare the cephalometric values among Pakistani males and females using commonly used sagittal skeletal measurements (ANB, Wits appraisal, Beta-angle) and newly developed cephalometric analyses (Yen-angle and W-angle). Study Design: Observational, cross-sectional study. Place and Duration of Study: Orthodontic Department of Baqai Medical University, Karachi, Pakistan, from August to October 2013. Methodology: A total of 209 pre-treatment lateral cephalometric radiographs of orthodontic patients were selected from departmental records, comprised of 92 males and 117 females. Radiographs were traced for measurements of ANB, Wits appraisal, Beta-angle, W-angle and Yen-angle. Patients were categorized into skeletal classes I, II, and III on the basis of performed measurements, incisor classification, and profile recorded from their records. Descriptive analysis was used to obtain median interquartile range in both the genders and Mann-Whitney U-test was used to observe gender dimorphism. Result: Skeletal class II was the most prevalent type of malocclusion. There were no difference in the obtained measurements between males and females except the Wits appraisal and Beta-angle in class II patients, which showed significant difference in values (p < 0.05). Conclusion: Pakistani population has no significant different difference in the craniofacial morphology of males and females, with the exception of Wits-appraisal and Beta-angle in class II cases. (author)

Spectrum of K ras mutations in Pakistani colorectal cancer patients

International Nuclear Information System (INIS)

Murtaza, B.N.; Bibi, A.; Rashid, M.U.; Khan, Y.I.; Chaudri, M.S.; Shakoori, A.R.

2013-01-01

The incidence of colorectal cancer (CRC) is increasing daily worldwide. Although different aspects of CRC have been studied in other parts of the world, relatively little or almost no information is available in Pakistan about different aspects of this disease at the molecular level. The present study was aimed at determining the frequency and prevalence of K ras gene mutations in Pakistani CRC patients. Tissue and blood samples of 150 CRC patients (64% male and 36% female) were used for PCR amplification of K ras and detection of mutations by denaturing gradient gel electrophoresis, restriction fragment length polymorphism analysis, and nucleotide sequencing. The K ras mutation frequency was found to be 13%, and the most prevalent mutations were found at codons 12 and 13. A novel mutation was also found at codon 31. The dominant mutation observed was a G to A transition. Female patients were more susceptible to K ras mutations, and these mutations were predominant in patients with a nonmetastatic stage of CRC. No significant differences in the prevalence of K ras mutations were observed for patient age, gender, or tumor type. It can be inferred from this study that Pakistani CRC patients have a lower frequency of K ras mutations compared to those observed in other parts of the world, and that K ras mutations seemed to be significantly associated with female patients

Spectrum of K ras mutations in Pakistani colorectal cancer patients

Energy Technology Data Exchange (ETDEWEB)

Murtaza, B.N.; Bibi, A. [School of Biological Sciences, University of the Punjab, Quaid-i-Azam Campus, Lahore (Pakistan); Rashid, M.U.; Khan, Y.I. [Shaukat Khanum Memorial Cancer Hospital and Research Centre, Johar Town, Lahore (Pakistan); Chaudri, M.S. [Services Institute of Medical Sciences, Lahore (Pakistan); Shakoori, A.R. [School of Biological Sciences, University of the Punjab, Quaid-i-Azam Campus, Lahore (Pakistan)

2013-11-29

The incidence of colorectal cancer (CRC) is increasing daily worldwide. Although different aspects of CRC have been studied in other parts of the world, relatively little or almost no information is available in Pakistan about different aspects of this disease at the molecular level. The present study was aimed at determining the frequency and prevalence of K ras gene mutations in Pakistani CRC patients. Tissue and blood samples of 150 CRC patients (64% male and 36% female) were used for PCR amplification of K ras and detection of mutations by denaturing gradient gel electrophoresis, restriction fragment length polymorphism analysis, and nucleotide sequencing. The K ras mutation frequency was found to be 13%, and the most prevalent mutations were found at codons 12 and 13. A novel mutation was also found at codon 31. The dominant mutation observed was a G to A transition. Female patients were more susceptible to K ras mutations, and these mutations were predominant in patients with a nonmetastatic stage of CRC. No significant differences in the prevalence of K ras mutations were observed for patient age, gender, or tumor type. It can be inferred from this study that Pakistani CRC patients have a lower frequency of K ras mutations compared to those observed in other parts of the world, and that K ras mutations seemed to be significantly associated with female patients.

Experiences of outreach workers in promoting smoking cessation to Bangladeshi and Pakistani men: longitudinal qualitative evaluation

Directory of Open Access Journals (Sweden)

Barton Pelham M

2011-06-01

Full Text Available Abstract Background Despite having high smoking rates, there have been few tailored cessation programmes for male Bangladeshi and Pakistani smokers in the UK. We report on a qualitative evaluation of a community-based, outreach worker delivered, intervention that aimed to increase uptake of NHS smoking cessation services and tailor services to meet the needs of Bangladeshi and Pakistani men. Methods This was a longitudinal, qualitative study, nested within a phase II cluster randomised controlled trial of a complex intervention. We explored the perspectives and experiences of five outreach workers, two stop smoking service managers and a specialist stop smoking advisor. Data were collected through focus group discussions, weekly diaries, observations of management meetings, shadowing of outreach workers, and one-to-one interviews with outreach workers and their managers. Analysis was undertaken using a modified Framework approach. Results Outreach workers promoted cessation services by word of mouth on the streets, in health service premises, in local businesses and at a wide range of community events. They emphasised the reasons for cessation, especially health effects, financial implications, and the impact of smoking on the family. Many smokers agreed to be referred to cessation services, but few attended, this in part being explained by concerns about the relative inflexibility of existing service provision. Although outreach workers successfully expanded service reach, they faced the challenges of perceived lack of awareness of the health risks associated with smoking in older smokers and apathy in younger smokers. These were compounded by perceptions of "lip service" being given to their role by community organisations and tensions both amongst the outreach workers and with the wider management team. Conclusions Outreach workers expanded reach of the service through taking it to diverse locations of relevance to Pakistani and Bangladeshi

Production of biomass in wet peatlands (paludiculture). The EU-AID project 'Wetland energy' in Belarus. Solutions for the substitution of fossil fuels (peat briquettes) by biomass from wet peatlands

Energy Technology Data Exchange (ETDEWEB)

Wichtmann, Wendelin [Michael Succow Stiftung fuer den Schutz der Natur, Greifswald (Germany); Haberl, Andreas; Tanneberger, Franziska

2012-07-01

In Belarus, a pilot project demonstrating site adapted management of wet peatlands for biomass production have started recently. In cooperation with local stakeholders, the currently environmentally unfriendly peat extraction for energy will be converted into a sustainable land use system. By replacing the peat briquettes with locally produced briquettes using biomass from rewetted peatlands the income situation of remote and rural areas will be improved. In various combustion trials of peatland biomass in Germany and Belarus the suitability of the material for energy production has been demonstrated. The EU-Aid funded project in Belarus is realized by the Michael Succow Foundation in cooperation with the International Sacharov Environmental University (ISEU) and the Institute for Nature Management of the National Academy of Sciences (IfNM). Applied, site-specific management concepts, employing site adapted machinery for reed and sedge vegetation on wet peatlands will not only result in avoidance of environmentally harmful peat extraction, but also in benefits for distinctive biodiversity. This site adapted peatlands management (paludiculture) comprises the reduction of greenhousegas (GHG) emissions by rewetting of drained peatlands and by the replacement of fossil fuels by biomass from these sites. Under favourable conditions additionally CO{sub 2} sequestration by new peat formation reestablished. The biomass will be harvested with site adapted machinery and processed to fuel briquettes. (orig.)

Working of Ideology in the TV Commercials of Cold Drinks in Pakistani Media

Science.gov (United States)

Ahmad, Madiha; Ahmad, Sofia; Ijaz, Nida; Batool, Sumera; Abid, Maratab

2015-01-01

The article aims at the analysis of the TV commercials of three carbonated cold drinks from Pakistani media. The analysis will be carried out using the three dimensional framework presented by Fairclough. Through the analysis, the ideological framing of the commercials will be brought to light. To achieve this purpose different techniques used by…

Developing a Research Instrument to Document Awareness, Knowledge, and Attitudes Regarding Breast Cancer and Early Detection Techniques for Pakistani Women: The Breast Cancer Inventory (BCI).

Science.gov (United States)

Naqvi, Atta Abbas; Zehra, Fatima; Ahmad, Rizwan; Ahmad, Niyaz

2016-12-09

There is a general hesitation in participation among Pakistani women when it comes to giving their responses in surveys related to breast cancer which may be due to the associated stigma and conservatism in society. We felt that no research instrument was able to extract information from the respondents to the extent it was needed for the successful execution of our study. The need to develop a research instrument tailored for Pakistani women was based upon the fact that most Pakistani women come from a conservative background and sometimes view this topic as provocative and believe discussing publicly about it as inappropriate. Existing research instruments exhibited a number of weaknesses during literature review. Therefore, using them may not be able to extract information concretely. A research instrument was, thus, developed exclusively. It was coined as, "breast cancer inventory (BCI)" by a panel of experts for executing a study aimed at documenting awareness, knowledge, and attitudes of Pakistani women regarding breast cancer and early detection techniques. The study is still in the data collection phase. The statistical analysis involved the Kaiser-Meyer-Olkin (KMO) measure and Bartlett's test for sampling adequacy. In addition, reliability analysis and exploratory factor analysis (EFA) were, also employed. This concept paper focuses on the development, piloting and validation of the BCI. It is the first research instrument which has high acceptability among Pakistani women and is able to extract adequate information from the respondents without causing embarrassment or unease.

Oligohydramnios in a pregnant Pakistani woman with Plasmodium vivax malaria

OpenAIRE

Binello, Nicolò; Brunetti, Enrico; Cattaneo, Federico; Lissandrin, Raffaella; Malfitano, Antonello

2014-01-01

In the Western world, the diagnosis and management of Plasmodium vivax malaria in pregnant women can be challenging, and the pathogenesis of adverse outcomes for both the mother and the foetus is still poorly known. The authors describe the case of a 29-year-old Pakistani woman at the 29th week of her second pregnancy, who was admitted to the Hospital following the abrupt onset of fever. At the time of admission, she had been living in Italy without travelling to any malaria-endemic areas for...

BRCA1 status in Pakistani breast cancer patients with moderate family history

International Nuclear Information System (INIS)

Moatter, T.; Pervez, S.; Khan, S.; Azam, I.

2011-01-01

Objective: To determine BRCA1 status in breast carcinoma patients of Pakistani origin. Study Design: Observational study. Place and Duration of Study: The Oncology Clinics of the Aga Khan University Hospital, Karachi, between May 2005 and December 2009. Methodology: Fifty three breast cancer patients based on clinical and laboratory diagnosis were recruited for this study. Moderate family history was defined as having a close relative (mother, daughter, sister) diagnosed with breast cancer under 45 years. Peripheral blood samples were collected from each patient in a 5 ml tube containing EDTA as anticoagulant. Subsequent to DNA extraction, mutational analysis of BRCA1 exons 2, 5, 6, 16, 20 and 22 was carried out using single strand conformation polymorphism (SSCP) assay while protein truncation test (PTT) was used to examine mutations in exon 11. All BRCA1 sequence variants were confirmed by DNA sequencing. Results: Twenty-three patients were diagnosed with early onset breast cancer, 30 patients had moderate family history. At the time of diagnosis, the median age of enrolled patients was 39 years (range 24-65 years). Out of 53 patients, analyzed by SSCP assay, mobility shift was detected in exon 6, 16 and 20 of three patients, whereas one patient was tested positive for mutation in exon 11 by PTT assays. All patients with BRCA1 mutations were further confirmed by DNA sequencing analysis. In exon 16 c.4837A > G was confirmed, which is a common polymorphism reported in several populations including Asians. Moreover, mutations in exon 6 (c.271T > G), exon 20 (c.5231 del G) and exon 11 (c.1123 T > G) were reported first time in the Pakistani population. Several BRCA1 mutations were observed in Pakistani breast cancer patients with moderate family history. Therefore, mutation-based genetic counselling for patients with moderate family history can facilitate management, if one first or second degree relative or early onset disease is apparent. (author)

Nanometre-sized pores in coal: Variations between coal basins and coal origin

Science.gov (United States)

Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

2018-01-01

We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

Promoting smoking cessation in Pakistani and Bangladeshi men in the UK: pilot cluster randomised controlled trial of trained community outreach workers

Directory of Open Access Journals (Sweden)

Barton Pelham

2011-08-01

Full Text Available Abstract Background Smoking prevalence is high among Pakistani and Bangladeshi men in the UK, but there are few tailored smoking cessation programmes for Pakistani and Bangladeshi communities. The aim of this study was to pilot a cluster randomised controlled trial comparing the effectiveness of Pakistani and Bangladeshi smoking cessation outreach workers with standard care to improve access to and the success of English smoking cessation services. Methods A pilot cluster randomised controlled trial was conducted in Birmingham, UK. Geographical lower layer super output areas were used to identify natural communities where more than 10% of the population were of Pakistani and Bangladeshi origin. 16 agglomerations of super output areas were randomised to normal care controls vs. outreach intervention. The number of people setting quit dates using NHS services, validated abstinence from smoking at four weeks, and stated abstinence at three and six months were assessed. The impact of the intervention on choice and adherence to treatments, attendance at clinic appointments and patient satisfaction were also assessed. Results We were able to randomise geographical areas and deliver the outreach worker-based services. More Pakistani and Bangladeshi men made quit attempts with NHS services in intervention areas compared with control areas, rate ratio (RR 1.32 (95%CI: 1.03-1.69. There was a small increase in the number of 4-week abstinent smokers in intervention areas (RR 1.30, 95%CI: 0.82-2.06. The proportion of service users attending weekly appointments was lower in intervention areas than control areas. No difference was found between intervention and control areas in choice and adherence to treatments or patient satisfaction with the service. The total cost of the intervention was £124,000; an estimated cost per quality-adjusted life year (QALY gained of £8,500. Conclusions The intervention proved feasible and acceptable. Outreach workers expanded

Developing a Research Instrument to Document Awareness, Knowledge, and Attitudes Regarding Breast Cancer and Early Detection Techniques for Pakistani Women: The Breast Cancer Inventory (BCI

Directory of Open Access Journals (Sweden)

Atta Abbas Naqvi

2016-12-01

Full Text Available There is a general hesitation in participation among Pakistani women when it comes to giving their responses in surveys related to breast cancer which may be due to the associated stigma and conservatism in society. We felt that no research instrument was able to extract information from the respondents to the extent it was needed for the successful execution of our study. The need to develop a research instrument tailored for Pakistani women was based upon the fact that most Pakistani women come from a conservative background and sometimes view this topic as provocative and believe discussing publicly about it as inappropriate. Existing research instruments exhibited a number of weaknesses during literature review. Therefore, using them may not be able to extract information concretely. A research instrument was, thus, developed exclusively. It was coined as, “breast cancer inventory (BCI” by a panel of experts for executing a study aimed at documenting awareness, knowledge, and attitudes of Pakistani women regarding breast cancer and early detection techniques. The study is still in the data collection phase. The statistical analysis involved the Kaiser-Meyer-Olkin (KMO measure and Bartlett’s test for sampling adequacy. In addition, reliability analysis and exploratory factor analysis (EFA were, also employed. This concept paper focuses on the development, piloting and validation of the BCI. It is the first research instrument which has high acceptability among Pakistani women and is able to extract adequate information from the respondents without causing embarrassment or unease.

Pakistani childrens’ views of TV advertising

Directory of Open Access Journals (Sweden)

Muhammad Kashif

2012-12-01

Full Text Available This qualitative study explores Pakistani children’s views regarding TV advertising and outlines the factors impacting their choice of snack brands. Thirty-six children from three schools were selected purposefully and qualitative data was collected through focus group sessions held in schools. Findings suggest that children understand the intended message of snack brand advertisers. Different variants of brands focusing on some product- and non-product related elements are considered imperative, contributing towards purchase. Children identify brands through jingles and cartoon characters and are well-aware of the logic behind TV advertising. This study highlighted children as knowledgeable, straightforward, fun-loving and rational consumers, all of which have some important implications for food marketers. The research is an original contribution to the work in the field of consumer socialization; it is intended to help the readers understand children’s attitude with regard to TV advertising, and identify some of the elements contributing to the choice of snack brands among children.

[A social history of carbon monoxide poisoning in Korea in 1960s: from an accident due to carelessness to a social disease].

Science.gov (United States)

Kim, Ock-Joo; Park, Se Hong

2012-08-31

This paper deals with social history of carbon monoxide poisoning in Korea in 1960s. From the mid 1950s, Korean society began to use coal briquettes (Yeontan) for fuel for cooking and heating in the winter, especially in urban area. As the use of coal briquettes replaced fire woods which had been used as fuel in traditional Korean society for centuries, incidence and deaths from carbon monoxide poisoning increased dramatically during the 1960s. The coal briquettes were used to heat the living rooms through "Ondol" arrangement. The coal briquettes at the kitchen place make the heated air and smoke, which pass through the horizontal space under a stone floor of the room and escape through chimney at the opposite site of the kitchen. This Ondol system could make leakage of carbon monoxide easily and thereby kill people who sleep in the room. In the 1960s, carbon monoxide poisoning by briquettes gas was a serious health problem to kill more people than all of the infectious diseases. It was a unique and very serious health hazard in 1960s Korea. No other place in the world has experienced such a high mortality and incidence from the briquettes gas as in Korea. Employing newspaper articles and epidemiological papers, this paper analyzes how the Korean society experienced and perceived carbon monoxide poisoning (CO poisoning) in 1960s. It also follows how the perception changed over time and how the changes affected social responses to CO poisoning. In the early 1960s, the CO poisoning was perceived as an accident due to carelessness of the people who did not fix the leakages of the Ondol system or that of the people who built the Ondol improperly. Mostly CO poisoning was the casualty caused by carelessness and ignorance of the poor class. The prevention measure was mainly education which would enlighten the ignorant so that they care about CO poisoning and their lives. It was the victims who were to be blamed, for they caused the their poisoning with their own

Validation Study of the Mini-Mental State Examination in Urdu Language for Pakistani Population.

Science.gov (United States)

Awan, Safia; Shahbaz, Naila; Akhtar, Syed Wasim; Ahmad, Arsalan; Iqbal, Sadaf; Ahmed, Sellal; Naqvi, Haider; Wasay, Mohammad

2015-01-01

Validation study of the Mini-Mental State Examination in Urdu language for Pakistani population. This study was conducted primarily to validate and determine the optimal cutoff score in the diagnosis of dementia among Pakistani's and study the effects of gender and education on the MMSE performance in our population. Four hundred participants took part in the study. Patient with dementia recruited from five major hospitals from Pakistan. The MMSE was translated into Urdu. There were 61 men and 39 women in dementia group and 225 men and 75 women in the control group. The mean score of Urdu MMSE were lower in patients with dementia 18.5 ± 5.6 (range 0-30) as compared to the controls 26.8 ± 2.6 (range 7-30). This difference between groups was statistically significant (p<0.001). Educational based MMSE score below 15 yielded perfect sensitivity and specificity for the diagnosis of dementia. These finding confirm the influence of level of education on MMSE score and education stratified cutoff scores should be used while screening for cognitive impairment in this population.

Anatomy of British Business School Brands: Attributes Affecting Choice Among Pakistani Postgraduate Students

Directory of Open Access Journals (Sweden)

Usman Ahmad

2014-06-01

Full Text Available The research studies that investigate business school brands from an Asian consumer perspective are scarce. Current study aims at discovering the branding attributes of UK Business Schools that influence Pakistani business students to apply for admission in higher degrees. Following a naturalistic tradition, data has been collected through semi-structured interviews from a sample of 25 students who were planning to study in United Kingdom. The respondents were identified through personal sources and were later selected using the purposive sampling technique. Thematic analysis was performed to generate themes from the collected data. The data analysis generated four dominant themes that influence the choice of a business school in United Kingdom. These are “financial assistance”, “employability”, “brand reputation” and “rankings”. The study is a pioneer work in the field of university branding from a developing country perspective of Pakistan. The research will be useful to British higher education marketers in devising student-centered branding initiatives. It will also benefit the Pakistani academia, as the country can develop business school brands as well by imparting these attributes to better compete with business schools in UK.

Obesity and Minority--Changing Meanings of Big Bodies among Young Pakistani Obesity Patients in Norway

Science.gov (United States)

Wathne, Kjetil; Mburu, Christina Brux; Middelthon, Anne-Lise

2015-01-01

Globally, paediatric obesity causes widespread concern, and the role of ethnicity is an important focus. Investigating how culture can mediate health-related behaviour through ideas about bodies, food and physical activity, while addressing a notion that the Pakistani community in Norway is particularly conservative and slow to change, this…

Briquette fuel production from wastewater sludge of beer industry and biodiesel production wastes

Science.gov (United States)

Nusong, P.; Puajindanetr, S.

2018-04-01

The production of industrial wastes is increasing each year. Current methods of waste disposal are severely impacting the environment. Utilization of industrial wastes as an alternative material for fuel is gaining interest due to its environmental friendliness. Thus, the objective of this research was to study the optimum condition for fuel briquettes produced from wastewater sludge of the beer industry and biodiesel production wastes. This research is divided into two parts. Part I will study the effects of carbonization of brewery wastewater sludge for high fixed carbon. Part II will study the ratio between brewery wastewater sludge and bleaching earth for its high heating value. The results show that the maximum fixed carbon of 10.01% by weight was obtained at a temperature of 350 °C for 30 minutes. The appropriate ratio of brewery wastewater sludge and bleaching earth by weight was 95:5. This condition provided the highest heating value of approximately 3548.10 kcal/kg.

A Controversial Role Model for Pakistani Women

Directory of Open Access Journals (Sweden)

Faiza Mushtaq

2012-03-01

Full Text Available Al-Huda is a movement of Islamic education and reform with a dedicated female following in Pakistani cities. Its founder and leader is a woman, Dr. Farhat Hashmi, who has become a well-known public figure in Pakistan. This paper explores how Hashmi derives her authority, displays it, and defends it against challenges. Women who become active participants in her classes claim she transforms their understanding of Islam and inspires them to change their lives. However she is criticized by the secular-liberal elites of the country and by the traditional male leadership of Islamic institutions, who question her religious expertise and are uncomfortable with the role of both gender and class in this movement. This analysis highlights the collective interactions and organizational innovations through which Hashmi’s teachings acquire an authoritative status for selected women.

Coal geopolitics

International Nuclear Information System (INIS)

Giraud, P.N.; Suissa, A.; Coiffard, J.; Cretin, D.

1991-01-01

This book divided into seven chapters, describes coal economic cycle. Chapter one: coals definition; the principle characteristics and properties (origin, calorific power, international classification...) Chapter two: the international coal cycle: coal mining, exploration, coal reserves estimation, coal handling coal industry and environmental impacts. Chapter three: the world coal reserves. Chapter four: the consumptions, productions and trade. Chapter five: the international coal market (exporting mining companies; importing companies; distributors and spot market operators) chapter six: the international coal trade chapter seven: the coal price formation. 234 refs.; 94 figs. and tabs [fr

Molecular and Clinical Studies of X-linked Deafness Among Pakistani Families

OpenAIRE

Waryah, Ali M.; Ahmed, Zubair M.; Choo, Daniel I.; Sisk, Robert A.; Binder, Munir A.; Shahzad, Mohsin; Khan, Shaheen N.; Friedman, Thomas B.; Riazuddin, Sheikh; Riazuddin, Saima

2011-01-01

There are 68 sex-linked syndromes that include hearing loss as one feature and five sex-linked nonsyndromic deafness loci listed in the OMIM database. The possibility of additional such sex-linked loci was explored by ascertaining three unrelated Pakistani families (PKDF536, PKDF1132, PKDF740) segregating X-linked recessive deafness. Sequence analysis of POU3F4 (DFN3) in affected members of families PKDF536 and PKDF1132 revealed two novel nonsense mutations, p.Q136X and p.W114X, respectively....

Relation of Home Chaos to Cognitive Performance and Behavioral Adjustment of Pakistani Primary School Children

Science.gov (United States)

Shamama-tus-Sabah, Syeda; Gilani, Nighat; Wachs, Theodore D.

2011-01-01

Recent findings from Western developed countries have linked home chaos to children's cognitive performance and behavioral problems. In the present paper we test whether the same pattern of associations can be replicated in a non-Western developing country. Our sample was 203 Pakistani primary school children. To assess home chaos the Confusion,…

In silico analysis of a disease-causing mutation in PCDH15 gene in a consanguineous Pakistani family with Usher phenotype

Directory of Open Access Journals (Sweden)

Shamim Saleha

2016-05-01

Full Text Available AIM: To map Usher phenotype in a consanguineous Pakistani family and identify disease-associated mutation in a causative gene to establish phenotype-genotype correlation. METHODS: A consanguineous Pakistani family in which Usher phenotype was segregating as an autosomal recessive trait was ascertained. On the basis of results of clinical investigations of affected members of this family disease was diagnosed as Usher syndrome (USH. To identify the locus responsible for the Usher phenotype in this family, genomic DNA from blood sample of each individual was genotyped using microsatellite Short Tandem Repeat (STR markers for the known Usher syndrome loci. Then direct sequencing was performed to find out disease associated mutations in the candidate gene. RESULTS: By genetic linkage analysis, the USH phenotype of this family was mapped to PCDH15 locus on chromosome 10q21.1. Three different point mutations in exon 11 of PCDH15 were identified and one of them, c.1304A>C was found to be segregating with the disease phenotype in Pakistani family with Usher phenotype. This, c.1304A>C transversion mutation predicts an amino-acid substitution of aspartic acid with an alanine at residue number 435 (p.D435A of its protein product. Moreover, in silico analysis revealed conservation of aspartic acid at position 435 and predicated this change as pathogenic. CONCLUSION: The identification of c.1304A>C pathogenic mutation in PCDH15 gene and its association with Usher syndrome in a consanguineous Pakistani family is the first example of a missense mutation of PCDH15 causing USH1 phenotype. In previous reports, it was hypothesized that severe mutations such as truncated protein of PCDH15 led to the Usher I phenotype and that missense variants are mainly responsible for non-syndromic hearing impairment.

In silico analysis of a disease-causing mutation in PCDH15 gene in a consanguineous Pakistani family with Usher phenotype.

Science.gov (United States)

Saleha, Shamim; Ajmal, Muhammad; Jamil, Muhammad; Nasir, Muhammad; Hameed, Abdul

2016-01-01

To map Usher phenotype in a consanguineous Pakistani family and identify disease-associated mutation in a causative gene to establish phenotype-genotype correlation. A consanguineous Pakistani family in which Usher phenotype was segregating as an autosomal recessive trait was ascertained. On the basis of results of clinical investigations of affected members of this family disease was diagnosed as Usher syndrome (USH). To identify the locus responsible for the Usher phenotype in this family, genomic DNA from blood sample of each individual was genotyped using microsatellite Short Tandem Repeat (STR) markers for the known Usher syndrome loci. Then direct sequencing was performed to find out disease associated mutations in the candidate gene. By genetic linkage analysis, the USH phenotype of this family was mapped to PCDH15 locus on chromosome 10q21.1. Three different point mutations in exon 11 of PCDH15 were identified and one of them, c.1304A>C was found to be segregating with the disease phenotype in Pakistani family with Usher phenotype. This, c.1304A>C transversion mutation predicts an amino-acid substitution of aspartic acid with an alanine at residue number 435 (p.D435A) of its protein product. Moreover, in silico analysis revealed conservation of aspartic acid at position 435 and predicated this change as pathogenic. The identification of c.1304A>C pathogenic mutation in PCDH15 gene and its association with Usher syndrome in a consanguineous Pakistani family is the first example of a missense mutation of PCDH15 causing USH1 phenotype. In previous reports, it was hypothesized that severe mutations such as truncated protein of PCDH15 led to the Usher I phenotype and that missense variants are mainly responsible for non-syndromic hearing impairment.

The Development of a Curriculum for Renewable Energy: A Case Study of Charcoal Briquettes from Agricultural Residues for Environmental Literacy of Secondary School Students at Samaki Wittaya Municipality School

Science.gov (United States)

Klakayan, Jagree; Singseewo, Adisak

2016-01-01

This research aimed to (1) design a curriculum on Production of Charcoal Briquettes from Agricultural Residues, (2) implement the designed curriculum, and (3) study and compare the learning achievements of Matthayomsuksa 3 students at Samakee Wittaya Municipality School in terms of knowledge, learning skills, and participation in the production of…

Coal 1992

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

ACR's Coal 1992, the successor to the ACR Coal Marketing Manual, contains a comprehensive set of data on many aspects of the Australian coal industry for several years leading up to 1992. Tables and text give details of coal production and consumption in New South Wales, Queensland and other states. Statistics of the Australian export industry are complemented by those of South Africa, USA, New Zealand, Canada, Indonesia, China, Colombia, Poland and ex-USSR. Also listed are prices of Australian coking and non-coking coal, Australian coal stocks (and those of other major countries), loading port capacities, freight rates and coal quality requirements (analysis of coals by brand and supplier). A listing of Australian coal exporting companies is provided. A description of the spot Coal Screen Dealing System is given. World hard coal imports are listed by country and coal imports by major Asian countries tabulated. A forecast of demand by coal type and country up to the year 2000 is included.

Characterization of Coal Porosity for Naturally Tectonically Stressed Coals in Huaibei Coal Field, China

Science.gov (United States)

Li, Xiaoshi; Hou, Quanlin; Li, Zhuo; Wei, Mingming

2014-01-01

The enrichment of coalbed methane (CBM) and the outburst of gas in a coal mine are closely related to the nanopore structure of coal. The evolutionary characteristics of 12 coal nanopore structures under different natural deformational mechanisms (brittle and ductile deformation) are studied using a scanning electron microscope (SEM) and low-temperature nitrogen adsorption. The results indicate that there are mainly submicropores (2~5 nm) and supermicropores (coal and mesopores (10~100 nm) and micropores (5~10 nm) in brittle deformed coal. The cumulative pore volume (V) and surface area (S) in brittle deformed coal are smaller than those in ductile deformed coal which indicates more adsorption space for gas. The coal with the smaller pores exhibits a large surface area, and coal with the larger pores exhibits a large volume for a given pore volume. We also found that the relationship between S and V turns from a positive correlation to a negative correlation when S > 4 m2/g, with pore sizes coal. The nanopore structure (coal. PMID:25126601

Justification of rational parameters of briquetting using mechanic activation techniques

Science.gov (United States)

Nikolaeva, L. A.; Burenina, O. N.

2017-12-01

The paper illustrates results of development of technology and compositions of briquetting substandard lignite waste with the use of tar as a binder, modified with mechanically activated organic-mineral fillers. The influence of highly disperse additives and technological briquetting regimes on the structure formation and the qualitative characteristics of fuel brown coal briquettes is considered.

Analysis of toxic metals in branded Pakistani herbal products

International Nuclear Information System (INIS)

Saeed, M.; Muhammad, N.; Khan, H.

2010-01-01

The present study was designed to estimate the concentration of heavy toxic metals in Pakistani herbal products frequently used for the treatment of various ailments. For this purpose, twenty five herbal products of well reputed herbal manufacturers were selected. The results of our investigation revealed that the concentrations of lead, cadmium, nickel and chromium were far beyond the permissible limits proposed by the International Regulatory Authorities for herbal drugs. Therefore, this study conveys a strong message to the ministry of health to establish proper rules and regulations for the validation of herbal products on scientific grounds in order to protect the general public from the harmful effects of these heavy metals in herbal products. (author)

Study of technical and economic feasibility of a manufacturing briquettes for energy generation; Estudo da viabilidade tecnico-economica de uma fabrica de briquetes para fins de geracao energetica

Energy Technology Data Exchange (ETDEWEB)

Silva, Claudinei Augusto da; Simoes, Andre Felipe [Universidade Estadual de Campinas (FEM/UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica], Emails: claudinei@fem.unicamp.br, afsimoes@fem.unicamp.br; Felfli, Felix Fonseca; Mesa Perez, Juan Miguel [Bioware Tecnologia, Campinas SP (Brazil); Rocha, Jose Dilcio [Universidade Estadual de Campinas (NIPE/UNICAMP), SP (Brazil). Nucleo Interdisciplinar de Planejamento Energetico

2006-07-01

Current scenario indicates that renewable energy sources are expected to play an increasingly important role in the world energy matrix, mainly due to a potential reduction of fossil fuel reserves and environment issues. In this context, the use of alternative energy sources, specifically biomass briquettes, shows up as a great opportunity. However, it is known that an economic feasibility assessment for the project depends on decision-making factors such as equipment, labor and material implementation. All costs and investments were calculated. A company headquartered in the city of Tiete, Sao Paulo State, analyzed the total costs of implementing a high density briquette factory. Tow scenarios were considered. In scenario 1, with tax exemption, the Net Present Value (NPV) is positive and the Intern Rate of Return is 16,9%, is an economic feasible scenario. Scenario 2, with no tax exemption, is not economically feasible, the NPV is negative and the Intern Rate Return is 13,9%, lower than 15.0% of the minimum rate of investor attractiveness. (author)

Coal upgrading

Energy Technology Data Exchange (ETDEWEB)

Nunes, S. [IEA Clean Coal Centre, London (United Kingdom)

2009-10-15

This report examines current technologies and those likely to be used to produce cleaner coal and coal products, principally for use in power generation and metallurgical applications. Consideration is also given to coal production in the leading coal producing countries, both with developed and developing industries. A range of technologies are considered. These include the coal-based liquid fuel called coal water mixture (CWM) that may compete with diesel, the production of ultra-clean coal (UCC) and coal liquefaction which competes with oil and its products. Technologies for upgrading coal are considered, especially for low rank coals (LRC), since these have the potential to fill the gap generated by the increasing demand for coal that cannot be met by higher quality coals. Potential advantages and downsides of coal upgrading are outlined. Taking into account the environmental benefits of reduced pollution achieved through cleaner coal and reduced transport costs, as well as other positive aspects such as a predictable product leading to better boiler design, the advantages appear to be significant. The drying of low rank coals improves the energy productively released during combustion and may also be used as an adjunct or as part of other coal processing procedures. Coal washing technologies vary in different countries and the implications of this are outlined. Dry separation technologies, such as dry jigging and electrostatic separation, are also described. The demonstration of new technologies is key to their further development and demonstrations of various clean coal technologies are considered. A number of approaches to briquetting and pelletising are available and their use varies from country to country. Finally, developments in upgrading low rank coals are described in the leading coal producing countries. This is an area that is developing rapidly and in which there are significant corporate and state players. 81 refs., 32 figs., 3 tabs.

Identification of a novel FBN1 gene mutation in a large Pakistani family with Marfan syndrome

NARCIS (Netherlands)

Micheal, S.; Khan, M.I.; Akhtar, F.; Weiss, M.M.; Islam, F.; Ali, M.; Qamar, R.; Maugeri, A.; Hollander, A.I. den

2012-01-01

PURPOSE: To describe a novel mutation in the fibrillin-1 (FBN1) gene in a large Pakistani family with autosomal dominant Marfan syndrome (MFS). METHODS: Blood samples were collected of 11 family members affected with Marfan syndrome, and DNA was isolated by phenol-extraction. The coding exons of

Coal

International Nuclear Information System (INIS)

Teissie, J.; Bourgogne, D. de; Bautin, F.

2001-12-01

Coal world production represents 3.5 billions of tons, plus 900 millions of tons of lignite. 50% of coal is used for power generation, 16% by steel making industry, 5% by cement plants, and 29% for space heating and by other industries like carbo-chemistry. Coal reserves are enormous, about 1000 billions of tons (i.e. 250 years of consumption with the present day rate) but their exploitation will be in competition with less costly and less polluting energy sources. This documents treats of all aspects of coal: origin, composition, calorific value, classification, resources, reserves, production, international trade, sectoral consumption, cost, retail price, safety aspects of coal mining, environmental impacts (solid and gaseous effluents), different technologies of coal-fired power plants and their relative efficiency, alternative solutions for the recovery of coal energy (fuel cells, liquefaction). (J.S.)

CoalVal-A coal resource valuation program

Science.gov (United States)

Rohrbacher, Timothy J.; McIntosh, Gary E.

2010-01-01

CoalVal is a menu-driven Windows program that produces cost-of-mining analyses of mine-modeled coal resources. Geological modeling of the coal beds and some degree of mine planning, from basic prefeasibility to advanced, must already have been performed before this program can be used. United States Geological Survey mine planning is done from a very basic, prefeasibility standpoint, but the accuracy of CoalVal's output is a reflection of the accuracy of the data entered, both for mine costs and mine planning. The mining cost analysis is done by using mine cost models designed for the commonly employed, surface and underground mining methods utilized in the United States. CoalVal requires a Microsoft Windows? 98 or Windows? XP operating system and a minimum of 1 gigabyte of random access memory to perform operations. It will not operate on Microsoft Vista?, Windows? 7, or Macintosh? operating systems. The program will summarize the evaluation of an unlimited number of coal seams, haulage zones, tax entities, or other area delineations for a given coal property, coalfield, or basin. When the reader opens the CoalVal publication from the USGS website, options are provided to download the CoalVal publication manual and the CoalVal Program. The CoalVal report is divided into five specific areas relevant to the development and use of the CoalVal program: 1. Introduction to CoalVal Assumptions and Concepts. 2. Mine Model Assumption Details (appendix A). 3. CoalVal Project Tutorial (appendix B). 4. Program Description (appendix C). 5. Mine Model and Discounted Cash Flow Formulas (appendix D). The tutorial explains how to enter coal resource and quality data by mining method; program default values for production, operating, and cost variables; and ones own operating and cost variables into the program. Generated summary reports list the volume of resource in short tons available for mining, recoverable short tons by mining method; the seam or property being mined

Coking coal outlook from a coal producer's perspective

International Nuclear Information System (INIS)

Thrasher, E.

2008-01-01

Australian mine production is recovering from massive flooding while Canadian coal shipments are limited by mine and rail capacity. Polish, Czech, and Russian coking coal shipments have been reduced and United States coking coal shipments are reaching their maximum capacity. On the demand side, the Chinese government has increased export taxes on metallurgical coal, coking coal, and thermal coal. Customers seem to be purchasing in waves and steel prices are declining. This presentation addressed the global outlook for coal as well as the challenges ahead in terms of supply and demand. Supply challenges include regulatory uncertainty; environmental permitting; labor; and geology of remaining reserves. Demand challenges include global economic uncertainty; foreign exchange values; the effect of customers making direct investments in mining operations; and freight rates. Consolidation of the coal industry continued and several examples were provided. The presentation also discussed other topics such as coking coal production issues; delayed mining permits and environmental issues; coking coal contract negotiations; and stock values of coking coal producers in the United States. It was concluded that consolidation will continue throughout the natural resource sector. tabs., figs

Effects of malnutrition on the erythrocyte fatty acid composition and plasma vitamin E levels of Pakistani children

NARCIS (Netherlands)

Smit, EN; Dijkstra, JM; Schnater, TA; Seerat, E; Muskiet, FAJ; Boersma, ER

Erythrocyte fatty acids and plasma vitamin E concentrations were determined in 47 grade 2, and 21 grade 3 malnourished Pakistani children (ages 4-56 months). Data were compared with those of 26 age- and sex-matched apparently healthy controls. Evaluation with three statistical approaches revealed

Coal contract cost reduction through resale of coal

International Nuclear Information System (INIS)

Simon, R.

1990-01-01

The weak coal market of the 1980's has enabled utilities and other users of coal to enjoy stable or falling prices for coal supplies. Falling prices for coal stimulated the renegotiation of numerous coal contracts in recent years, as buyers look to take advantage of lower fuel prices available in the marketplace. This paper examines the use of coal resale transactions as a means of reducing fuel costs, and analyzes the benefits and risks associated with such transactions

Changes in food habits and motivation for healthy eating among Pakistani women living in Norway: results from the InnvaDiab-DEPLAN study.

Science.gov (United States)

Johansen, Karianne S; Bjørge, Benedikte; Hjellset, Victoria Telle; Holmboe-Ottesen, Gerd; Råberg, Marte; Wandel, Margareta

2010-06-01

Pakistani women in Oslo have high risk of overweight and type 2 diabetes. The objective is to present the effect of an intervention study on Pakistani women's intentions to change dietary behaviour and changes made in dietary intake. The intervention group received culturally adapted lifestyle education, including diet and physical activity. The questionnaire, applied before and after the 7-month intervention, included FFQ and questions on intentions to change. Oslo, Norway. A total of 198 Pakistani women, aged 25-63 years, randomised into control and intervention groups. There was a shift in distribution of intentions to change the intake of selected foods in the intervention group after the intervention, resulting in significant differences between the groups. The daily intake of vegetables, fruits and fruit juice had increased (P = 0.043), and the intake of red meats (P = 0.001), full fat milk/yoghurt (P = 0.027) and sugar-rich drinks (P Pakistani women;s intentions to make their diet healthier, and also to induce some beneficial, however modest, self-reported changes in diet.

Mechanical Evaluation for the Quality Control of Biomass Pellets and Briquettes

Energy Technology Data Exchange (ETDEWEB)

Freitas Seabra da Rocha, Saulo Henrique [RWTH Aachen Univ. (Germany). KoBrA - Coking, Briquetting and Thermal Waste Treatment Group

2006-07-15

Biomass densification through compression machine leads to numerous benefits, such as decreased dust emission, transportation, and maintenance costs. However, if the mechanical strength of the Pellets and briquettes is not high enough, breaks and abrasion lead to low efficiency. Quality evaluation before pelleting or briquetting can avoid these problems. The most common mechanical strength evaluation methods are simple and fast, but their accuracy and precision are limited. In this paper three methods for mechanical strength evaluation are reviewed, tested and statistically compared. Compacted bodies in different dimensions of typical materials, like sawdust, bark and lignite, were produced, and tested with the mentioned methods to get different values of mechanical strength. The correlation coefficient was used to compare the accuracy and precision of those methods. The Point Load Strength method showed a linear variation error and a poor correlation coefficient value (R2 = 0.71-0.78). The Brazilian Test had a reasonably constant result, but the relative standard deviation was 22%, insufficient for a practical process optimization. The best results were produced from the Extended Planar Strength, with an excellent correlation coefficient value (R2 = 0.98). This technique will help to increase efficiency and save energy in the production process.

GENDER ROLES IN PAKISTANI-URDU WEDDING SONGS

Directory of Open Access Journals (Sweden)

Syeda Bushra Zaidi

2016-05-01

Full Text Available This qualitative study of Pakistani-Urdu wedding songs allows a closer look at the gender situation, and towards the understanding of the process of construction and perpetuation of gender-based stereotypes. However, the major concern of this study is to understand the portrayal of each gender along with the question that does such portrayal underlines the traditional gender roles and gender inequality. Taking a discourse analysis perspective, this study analyzes textual data from the lyrics of the seventeen wedding songs. The song selection was based on purposive sampling technique. The data were collected through transcription and recording of the audios of the songs. As a result of thematic analysis thirteen themes emerged, ten portraying the female gender and four portraying the male gender. These themes reveal important findings that support and reinforce the gender-based stereotypes and also reflect gender hierarchy, normative heterosexual relationships, kinship norms and gender subversions.

Acceptability of GM foods among Pakistani consumers

Science.gov (United States)

Ali, Akhter; Rahut, Dil Bahadur; Imtiaz, Muhammad

2016-01-01

ABSTRACT In Pakistan majority of the consumers do not have information about genetically modified (GM) foods. In developing countries particularly in Pakistan few studies have focused on consumers' acceptability about GM foods. Using comprehensive primary dataset collected from 320 consumers in 2013 from Pakistan, this study analyzes the determinants of consumers' acceptability of GM foods. The data was analyzed by employing the bivariate probit model and censored least absolute deviation (CLAD) models. The empirical results indicated that urban consumers are more aware of GM foods compared to rural consumers. The acceptance of GM foods was more among females' consumers as compared to male consumers. In addition, the older consumers were more willing to accept GM food compared to young consumers. The acceptability of GM foods was also higher among wealthier households. Low price is the key factor leading to the acceptability of GM foods. The acceptability of the GM foods also reduces the risks among Pakistani consumers. PMID:27494790

Acceptability of GM foods among Pakistani consumers.

Science.gov (United States)

Ali, Akhter; Rahut, Dil Bahadur; Imtiaz, Muhammad

2016-04-02

In Pakistan majority of the consumers do not have information about genetically modified (GM) foods. In developing countries particularly in Pakistan few studies have focused on consumers' acceptability about GM foods. Using comprehensive primary dataset collected from 320 consumers in 2013 from Pakistan, this study analyzes the determinants of consumers' acceptability of GM foods. The data was analyzed by employing the bivariate probit model and censored least absolute deviation (CLAD) models. The empirical results indicated that urban consumers are more aware of GM foods compared to rural consumers. The acceptance of GM foods was more among females' consumers as compared to male consumers. In addition, the older consumers were more willing to accept GM food compared to young consumers. The acceptability of GM foods was also higher among wealthier households. Low price is the key factor leading to the acceptability of GM foods. The acceptability of the GM foods also reduces the risks among Pakistani consumers.

Maintenance of changes in food intake and motivation for healthy eating among Norwegian-Pakistani women participating in a culturally adapted intervention.

Science.gov (United States)

Helland-Kigen, Kaja Marie; Råberg Kjøllesdal, Marte Karoline; Hjellset, Victoria Telle; Bjørge, Benedikte; Holmboe-Ottesen, Gerd; Wandel, Margareta

2013-01-01

To investigate maintenance of changes in food intake and motivation for healthy eating at follow-up 2 data collection after a lifestyle intervention among Pakistani immigrant women. A culturally adapted lifestyle intervention, aiming at reducing the risk of type 2 diabetes mellitus. Data collection including FFQ and questions on intentions to change dietary behaviour was completed at baseline, right after the 7 ± 1 month intervention (follow-up 1) and 2-3 years after baseline (follow-up 2). Oslo, Norway. Pakistani women (n =198), aged 25-60 years, randomized into control and intervention groups. From follow-up 1 to follow-up 2 there was a shift from action to maintenance stages for intention to reduce fat intake (P diet.

Australian Coal Company Risk Factors: Coal and Oil Prices

OpenAIRE

M. Zahid Hasan; Ronald A. Ratti

2014-01-01

Examination of panel data on listed coal companies on the Australian exchange over January 1999 to February 2010 suggests that market return, interest rate premium, foreign exchange rate risk, and coal price returns are statistically significant in determining the excess return on coal companies’ stock. Coal price return and oil price return increases have statistically significant positive effects on coal company stock returns. A one per cent rise in coal price raises coal company returns ...

Coal Tar and Coal-Tar Pitch

Science.gov (United States)

Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

Coal summit II

Energy Technology Data Exchange (ETDEWEB)

1983-01-01

Various papers were presented on world coal trade. Papers include: Poland as a producer and exporter of coal; the dynamics of world coal trade; Cerrejon coal production perspectives; present state of the Australian coal industry; present state of the EC coal market and future prospects; prospects of US coal exports to Europe; forecast of Italian coal supply and demand through 1990; statistics from coal transportation outlook; status of world coal ports.

Barriers and facilitators to cervical cancer screening among Pakistani and Somali immigrant women in Oslo: a qualitative study

Directory of Open Access Journals (Sweden)

Gele AA

2017-07-01

Full Text Available Abdi A Gele,1,2 Samera A Qureshi,1 Prabhjot Kour,1 Bernadette Kumar,1 Esperanza Diaz1,3 1Norwegian Center for Minority Health Research, 2Department of Health, Institute of Nursing and Health Promotion, Oslo and Akershus University College, Oslo; 3Department of Global Public Health and Primary Care, University of Bergen, Bergen, Norway Abstract: Norway has a low incidence and mortality rate of cervical cancer, which is mainly due to the high participation rate of women in cervical cancer screening. However, the attendance of cervical cancer screening was reported to be low among immigrant women. For this reason, we conducted a qualitative study to obtain better insight into perceived barriers and challenges to cervical cancer screening among Somali and Pakistani women in the Oslo region. A convenient sample of 35 (18 Pakistani, 17 Somali women were recruited for the study in collaboration with Somali and Pakistani community partners. Focus group discussions were used to explore barriers and facilitators to cervical cancer screening, whereas the Ecological Model was used as the framework for the study. The study found three levels of barriers to cervical cancer screening. The individual level included a lack of understanding of the benefits of the screening. The sociocultural level included the stigma attached to the disease and the belief that women who are unmarried are sexually inactive. The system-related level included a lack of trust toward the health care system. Based on the study results, and using a common denominator approach for the immigrant groups included, the study recommends three communication strategies with the potential to improve women’s participation in cervical cancer screening: 1 in-person communication and information material at health centers; 2 verbal communication with women through seminars and workshops to educate them about their risk of cancer and the importance of screening and 3 the initiation of better recall

Perceptions of risk factors for diabetes among Norwegian-Pakistani women participating in a culturally adapted intervention.

Science.gov (United States)

Råberg Kjøllesdal, Marte K; Hjellset, Victoria T; Bjørge, Benedikte; Holmboe-Ottesen, Gerd; Wandel, Margareta

2011-06-01

To explore perceptions of diabetes risk factors among Pakistani immigrant women, as part of their explanatory model of the disease, and the changes in these perceptions after a culturally adapted intervention. Intervention study, carried out in Oslo, Norway, comprising 198 women. At baseline, about 75% of the women perceived sugar to be a risk factor for diabetes, about 30% mentioned physical inactivity and stress and close to 20% mentioned overweight. Twelve per cent could not identify any risk factors. When asked about foods to include in a diet to prevent diabetes, vegetables were mentioned by 45%, while 33% did not know any foods to include. Among those attending ≥60% of the educational sessions, the proportions mentioning little physical activity (pfood to include was reduced to 10% (p=0.004). Except for little physical activity, similar changes in responses were not registered in the control group. There is a need for improved knowledge about diabetes prevention among Pakistani immigrant women, and a culturally adapted intervention may contribute to this.

Biomass of clone of Eucalyptus grandis x urophylla for producing briquettes; Biomassa de clone de Eucalyptus grandis x Eucalyptus urophylla para producao de briquetes

Energy Technology Data Exchange (ETDEWEB)

Garcia, Eder Aparecido; Oguri, Guilherme [Universidade Estadual Paulista Julio de Mesquita Filho (FCA/UNESP), Botucatu, SP (Brazil). Fac. de Ciencias Agronomicas], e-mail: os_garcias@fca.unesp.br; Lancas, Kleber Pereira [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Botucatu, SP (Brazil). Fac. de Ciencias Agronomicas. Dept. de Engenharia Rural; Guerra, Saulo Philipe Sebastiao [Universidade Estadual Paulista Julio de Mesquita Filho (FCA/UNESP), Botucatu, SP (Brazil). Fac. de Ciencias Agronomicas. Dept. de Gestao e Tecnologia Agroindustrial

2011-07-01

The aim of this work was conducted to address forest biomass energy for briquette producing. In an area of dystrophic soil, seedlings of clones of Eucalyptus grandis x E. urophylla were planted in 2008, considering factors spacing and fertilization. The first dosage of fertilizer was 70 g/plant of NPK 6-30-6 and total coverage of 110 g/plant of NPK 20-0-20 with B and Zn. The spacing was 2.8x0.5 m, 2.8x1.0 m, 2.8x1.5 m, 2.8x2.0 m and 2.8x2.5 m. At 18 months, tree samples were collected to evaluate the basic density of wood (BDW), dry biomass of stem, branches and leaves. An assessment of the economic viability of each treatment was based on the sale of briquettes. BDW spacing of 2.8x1.0 m was 0.464 kg/m{sup 3}. The largest biomass of the stem occurred in 2.8x0.5 m spacing, with dosage 3, but economically unviable. The dry biomass of branches was only affected by dosage, reaching 17.68 t/ha in the third dose. Only fertilization was significant for leaf biomass. The highest income in the spacing was 2.8 x1.5 m with dosage 2. (author)

Estimating the risk of cardio vascular diseases among pakistani diabetics using uk pds risk engine

International Nuclear Information System (INIS)

Moazzam, A.; Amer, J.

2015-01-01

The concept of risk estimation of Coronary Heart Disease (CHD) is helpful for clinician to identifying high risk populations for their effective treatment. Latest studies recommended only initiating cardio-protective treatment in diabetic patients based on personalized CHD risk estimates so as to reduce undue harm from overly aggressive risk factor modification. The United Kingdom Prospective Diabetes Study (UK PDS) Risk Engine is a widely used tool to assess the risk of Cardio Vascular diseases (CVD) in diabetics. The literature search so far did not reveal any study of risk assessment among Pakistani Diabetics. Methods: This descriptive study is based on the data of 470 type-2 diabetics seen in Department of Endocrinology and Metabolism, Services Institute of Medical Sciences, Lahore during 2011. The data of these 470 patients was analyzed through UKPDS Risk Engine. CHD risk was calculated. Results: The 10 years risk of CHD, fatal CHD, stroke and fatal stroke was 9.4%, 4.4%, 1.7% and 0.2% respectively. Conclusions: The present study show a lower risk of CVD occurring among Pakistani diabetics as compared to studies from western countries. (author)

Molecular genetic analysis of consanguineous Pakistani families with autosomal recessive hypohidrotic ectodermal dysplasia.

Science.gov (United States)

Bibi, Nosheen; Ahmad, Saeed; Ahmad, Wasim; Naeem, Muhammad

2011-02-01

Hypohidrotic ectodermal dysplasia is an inherited disorder characterized by defective development of teeth, hairs and sweat glands. X-linked hypohidrotic ectodermal dysplasia is caused by mutations in the EDA gene, and autosomal forms of hypohidrotic ectodermal dysplasia are caused by mutations in either the EDAR or the EDARADD genes. To study the molecular genetic cause of autosomal recessive hypohidrotic ectodermal dysplasia in three consanguineous Pakistani families (A, B and C), genotyping of 13 individuals was carried out by using polymorphic microsatellite markers that are closely linked to the EDAR gene on chromosome 2q11-q13 and the EDARADD gene on chromosome 1q42.2-q43. The results revealed linkage in the three families to the EDAR locus. Sequence analysis of the coding exons and splice junctions of the EDAR gene revealed two mutations: a novel non-sense mutation (p.E124X) in the probands of families A and B and a missense mutation (p.G382S) in the proband of family C. In addition, two synonymous single-nucleotide polymorphisms were also identified. The finding of mutations in Pakistani families extends the body of evidence that supports the importance of EDAR for the development of hypohidrotic ectodermal dysplasia. © 2010 The Authors. Australasian Journal of Dermatology © 2010 The Australasian College of Dermatologists.

Coal-92

International Nuclear Information System (INIS)

Hillring, B.; Sparre, C.

1992-11-01

Swedish consumption of coal and coke during 1991 and trends in technology, environment and market aspects of coal use are reported. Steam coal use in the heating sector was unchanged from 1991, 1.2 Mtons. Reduced consumption in smaller district heating units (due to conversion to biofuels and gas) was compensated by increased use for power generation in cogeneration plants. Coal consumption in industry fell 0.10 Mton to 0.84 Mton due to lower production in one industry branch. Import of steam coal was 1.1 Mton (down 0.5 Mton from 1990) since new rules for strategic reserves allowed a reduction of stocks. During the last five years stocks have been reduced by 2 Mtons. Import of metallurgical coal was 1.6 Mton, unchanged from 1990. The report also gives statistics for the coal using plants in Sweden, on coal R and D, and on emission laws for coal firing. (9 tabs., 2 figs.)

A canonical splice site mutation in GIPC3 causes sensorineural hearing loss in a large Pakistani family

NARCIS (Netherlands)

Siddiqi, S.; Ismail, M.; Oostrik, J.; Munawar, S.; Mansoor, A.; Kremer, H.; Qamar, R.; Schraders, M.

2014-01-01

With homozygosity mapping we have identified two large homozygous regions on chromosome 3q13.11-q13.31 and chromosome 19p13.3-q31.32 in a large Pakistani family suffering from autosomal recessive nonsyndromic hearing impairment (arNSHI). The region on chromosome 19 overlaps with the previously

A newer concept of setting up coal refineries in coal utilising industries through environmentally sound clean coal technology of organosuper refining of coals

International Nuclear Information System (INIS)

Sharma, D.K.

1994-01-01

In order to reduce the losses of premium organic matter of coal and its immense potential energy which is present in the form of stronger interatomic and intramolecular bonding energies, a newer and convenient technique of recovering the premium organic matter from low grade coals by organosuper-refining technique which operates under ambient pressure conditions has been developed. The residual coal obtained can be used as environmentally clean fuel or as a feedstock for the industries based on carbonization and gasification. It is suggested that a beginning be made by setting up coal refineries in coal utilizing industries on the basis of the presently developed new technology of organosuper-refining of coals to recover premium grade organic chemical feed stocks from coals before utilizing coal by techniques such as bubble bed or recirculatory fluidized bed or pulverized coal combustion in thermal power stations, carbonization in steel plants or other carbonization units, gasification in fertilizer industries or in integrated coal gasification combined cycle power generation. Thus, coal refineries may produce value added aromatic chemical feed stocks, formed coke or coke manufacturing; and carbon fillers for polymers. (author). 100 refs., 1 fig

Adoption of Social Networking Sites among Pakistani University Students: A Case of Face-Book

OpenAIRE

Raja Irfan Sabir; Wasim Ahmad; Nabila Noor; Asad-ur-Rehman

2013-01-01

Since birth of Social Networking Sites (SNSs), these attracted millions of users from all around the world. The SNSs have changed the communication ways of people from more traditional to modern approaches. This study aims to examine diffusion and adoption of Facebook.com among Pakistani university students using Technology Acceptance Model (TAM) and Theory of Reasoned Action (TRA) with an extension of Theory of Planned Behavior (TPB). The study used stratified random & pre-tested questionnai...

Predicted coal production trends in Kentucky: The results of available coal resources, coal quality demands, and regulatory factors

International Nuclear Information System (INIS)

Watson, W.D.

1993-01-01

Many factors affect the viability of regional coal production markets including (1) coal quality and recoverable tonnage, (2) coal mining cost, (3) the regional and time varying patterns of coal demand growth, (4) regulations and other institutional constraints that affect coal demand and utilization, and (5) the regional array of coal transport modes and rates. This analysis integrates these factors into an assessment of coal production prospects (separately) for eastern and western Kentucky coal producing counties for the decade of the 90's. The integration indicates that eastern Kentucky coal production will peak and begin to decline by the end of the decade whereas western Kentucky coal production will continue to grow. No single factor explains these trends. There is plenty of available minable coal. The combination of changes in environmental regulations, some increase in coal mining costs, and the mining-out of low sulfur reserves are the main factors that account for the production trends

Utilizing Rice Husk Briquettes in Firing Crucible Furnace for Low Temperature Melting Metals in Nigeria

Directory of Open Access Journals (Sweden)

N. A. Musa

2012-08-01

Full Text Available The search for alternative fuels for firing crucible furnace for low temperature melting metals has become mandatory, as a result of the pollution problem associated with the use of fossil fuels, the expense of electricity and also deforestation as a result of the use of charcoal. An agricultural waste, rice husk, in briquette form was used as an alternative fuel to fire crucible furnace to melt lead, zinc and aluminium. Results showed that lead and zinc melted and reached their pouring temperatures of 3840C and 5300C in 70 minutes and 75 minutes respectively. Aluminium was raised to a maximum temperature of 5200C in 75 and 100 minutes.The average concentration of the pollutants (CO, SO2and NOX were found to be below the tolerance limit and that of TSP (Total Suspended Particulates was found to be within the tolerance limit stipulated by Federal Environmental Protection Agency (FEPA in Nigeria.

"Narrow-Minded and Oppressive" or a "Superior Culture"? Implications of Divergent Representations of Islam for Pakistani-American Youth

Science.gov (United States)

Ghaffar-Kucher, Ameena

2015-01-01

Drawing on ethnographic data, this article examines the complex terrain that working-class Pakistani-American youth must negotiate in their daily lives. Specifically, the article illustrates how particular views of Islam and Americanization manifest in particular sites and within educational discourses, and the resulting dissonance that youth…

A Transnational Community of Pakistani Muslim Women: Narratives of Rights, Honor, and Wisdom in a Women's Education Project

Science.gov (United States)

Khurshid, Ayesha

2012-01-01

Using ethnographic data, this article explores how Muslim women teachers from low-income Pakistani communities employ the notion of "wisdom" to construct and perform their educated subjectivity in a transnational women's education project. Through Butler's performativity framework, I demonstrate how local and global discourses overlap to…

Variability of Mercury Content in Coal Matter From Coal Seams of The Upper Silesia Coal Basin

Science.gov (United States)

Wierzchowski, Krzysztof; Chećko, Jarosław; Pyka, Ireneusz

2017-12-01

The process of identifying and documenting the quality parameters of coal, as well as the conditions of coal deposition in the seam, is multi-stage and extremely expensive. The taking and analyzing of seam samples is the method of assessment of the quality and quantity parameters of coals in deep mines. Depending on the method of sampling, it offers quite precise assessment of the quality parameters of potential commercial coals. The main kind of seam samples under consideration are so-called "documentary seam samples", which exclude dirt bands and other seam contaminants. Mercury content in coal matter from the currently accessible and exploited coal seams of the Upper Silesian Coal Basin (USCB) was assessed. It was noted that the mercury content in coal seams decreases with the age of the seam and, to a lesser extent, seam deposition depth. Maps of the variation of mercury content in selected lithostratigraphic units (layers) of the Upper Silesian Coal Basin have been created.

Firing a sub-bituminous coal in pulverized coal boilers configured for bituminous coals

Energy Technology Data Exchange (ETDEWEB)

N. Spitz; R. Saveliev; M. Perelman; E. Korytni; B. Chudnovsky; A. Talanker; E. Bar-Ziv [Ben-Gurion University of the Negev, Beer-Sheva (Israel)

2008-07-15

It is important to adapt utility boilers to sub-bituminous coals to take advantage of their environmental benefits while limiting operation risks. We discuss the performance impact that Adaro, an Indonesian sub-bituminous coal with high moisture content, has on opposite-wall and tangentially-fired utility boilers which were designed for bituminous coals. Numerical simulations were made with GLACIER, a computational-fluid-dynamic code, to depict combustion behavior. The predictions were verified with full-scale test results. For analysis of the operational parameters for firing Adaro coal in both boilers, we used EXPERT system, an on-line supervision system developed by Israel Electric Corporation. It was concluded that firing Adaro coal, compared to a typical bituminous coal, lowers NOx and SO{sub 2} emissions, lowers LOI content and improves fouling behavior but can cause load limitation which impacts flexible operation. 21 refs., 7 figs., 3 tabs.

Geochemistry of coals, coal ashes and combustion wastes from coal-fired power stations

International Nuclear Information System (INIS)

Vassilev, S.V.; Vassileva, C.G.

1997-01-01

Contents, concentration trends, and modes of occurrence of 67 elements in coals, coal ashes, and combustion wastes at eleven Bulgarian thermoelectric power stations (TPS) were studied. A number of trace elements in coal and coal ash have concentrations greater than their respective worldwide average contents (Clarke values). Trace elements are concentrated mainly in the heavy accessory minerals and organic matter in coal. In decreasing order of significance, the trace elements in coal may occur as: element-organic compounds; impurities in the mineral matter; major components in the mineral matter; major and impurity components in the inorganic amorphous matter; and elements in the fluid constituent. A number of trace elements in the waste products, similar to coal ashes, exceed known Clarke contents. Trace elements are mainly enriched in non-magnetic, heavy and fine-grained fractions of fly ash. They are commonly present as impurities in the glass phases, and are included in the crystalline components. Their accessory crystalline phases, element-organic compounds, liquid and gas forms, are of subordinate importance. Some elements from the chalcophile, lithophile and siderophile groups may release into the atmosphere during coal burning. For others, the combustion process appears to be a powerful factor causing their relative enrichment in the fly ash and rarely in the bottom ash and slag. 65 refs., 1 fig., 11 tabs

Differences in the pregnancy gestation period and mean birth weights in infants born to Indian, Pakistani, Bangladeshi and white British mothers in Luton, UK: a retrospective analysis of routinely collected data.

Science.gov (United States)

Garcia, Rebecca; Ali, Nasreen; Guppy, Andy; Griffiths, Malcolm; Randhawa, Gurch

2017-08-11

To compare mean birth weights and gestational age at delivery of infants born to Indian, Pakistani, Bangladeshi and white British mothers in Luton, UK. Retrospective analysis using routinely recorded secondary data in Ciconia Maternity information System, between 2008 and 2013. Luton, UK. Mothers whose ethnicity was recorded as white British, Bangladeshi, Pakistani or Indian and living in Luton, aged over 16, who had a live singleton birth over 24 weeks of gestation were included in the analysis (n=14 871). Primary outcome measures were mean birth weight and gestational age at delivery. After controlling for maternal age, smoking, diabetes, gestation age, parity and maternal height and body mass index at booking, a significant difference in infants' mean birth weight was found between white British and Indian, Pakistani and Bangladeshi infants, F(3, 12 287)=300.32, pmothers, compared with Indian mothers (Wald=8.192, df 1, pmothers and preterm delivery, when compared with Pakistani, Bangladeshi and white British women. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

New coal

Energy Technology Data Exchange (ETDEWEB)

1979-07-01

Specially dedicated to coal, this edition comprises a series of articles of general interest dealing with the position of the French coalmining industry (interview with M.P. Gardent), the coal market in France, the work of CERCHAR, etc. New techniques, in-situ gasification of deep coal, gasification of coal by nuclear methods, the conversion of coal into petrol, the Emile Huchet power plant of Houilleres du Bassin de Lorraine, etc., are dealt with.

Industrial use of coal and clean coal technology

Energy Technology Data Exchange (ETDEWEB)

Leibson, I; Plante, J J.M.

1990-06-01

This report builds upon two reports published in 1988, namely {ital The use of Coal in the Industrial, Commercial, Residential and Transportation Sectors} and {ital Innovative Clean Coal Technology Deployment}, and provides more specific recommendations pertaining to coal use in the US industrial sector. The first chapter addresses industrial boilers which are common to many industrial users. The subsequent nine chapters cover the following: coke, iron and steel industries; aluminium and other metals; glass, brick, ceramic, and gypsum industries; cement and lime industries; pulp and paper industry; food and kindred products; durable goods industry; textile industry; refining and chemical industry. In addition, appendices supporting the contents of the study are provided. Each chapter covers the following topics as applicable: energy overview of the industry sector being discussed; basic processes; foreign experience; impediments to coal use; incentives that could make coal a fuel of choice; current and projected use of clean coal technology; identification of coal technology needs; conclusions; recommendations.

Association of tumor necrosis factor alpha gene polymorphism G-308A with pseudoexfoliative glaucoma in the Pakistani population.

NARCIS (Netherlands)

Khan, M.I.; Micheal, S.; Rana, N.; Akhtar, F.; Hollander, A.I. den; Ahmed, A.; Qamar, R.

2009-01-01

PURPOSE: The purpose of the present study was to determine the role of the tumor necrosis factor alpha (TNF-alpha) gene polymorphism G-308A and total serum immunoglobulin E (TsIgE) levels in the onset of pseudoexfoliation glaucoma (PEXG) in Pakistani patients. METHODS: The TNF-alpha polymorphism

Behaviour Of Saline Irrigation Water Components In Pakistani Barley And Calcareous Soil Under Scheduling Irrigation Using Neutron Scattering Technique

International Nuclear Information System (INIS)

RIZK, M.A.

2010-01-01

This study aims to investigate the behaviour of cation uptake by Pakistani barley (genotype PK-30163) as affected by saline irrigation water, as well as cation distribution within the soil profile. This experiment was carried out at Soil and Water Research Department, Nuclear Research Centre, Atomic Energy Authority, Inshas, Egypt. The soil was transferred from Wadi Sudr (South Sinai, Egypt). It is salted affected soil (calcareous soil, EC = 4.3 dS/m) and was irrigated using ground water irrigation (12.5 dS/m). Nine used lysimeters were irrigated with three artificial saline water (0.3, 4 and 8 dS/m) using drip irrigation system. The irrigation schedule was carried out using neutron scattering technique according to the hydro physical properties of the soil. Pakistani barley (halophytic plant) was used to remove salts from the soil especially sodium cations. The cation uptake and cation distribution (Na, K, Ca, Mg) within the soil profile were studied.The data indicated that roots of barley collected within 0-15 cm layer showed high cation uptake that made the salt concentrations in this layer low. Sodium uptake ratio was 43, 37 and 47% from total cation uptake by using fresh water (0.3 dS/m), 4 and 8 dS/m, respectively. The maximum uptake for Na, K, Ca and Mg was 20.51, 19.13, 3.98 and 12.81 g/lys at 5.69, 3.05, 6.56 and 4.15 dS/m, respectively. It was found that Pakistani barley preferred Mg uptake rather than Ca uptake.

Use of Information Technology in Business Processes In Pakistani and Multinational Pharmaceutical Companies in Korangi.

Directory of Open Access Journals (Sweden)

IRFAN UL HASAN

Full Text Available This study presents an analysis of IT use and Business Processes (BP in Korangi pharmas. Information system usage and manufacturing performance are moderately associated within the sample. There is little difference in the utilization of IT between the multinational and Pakistani firms. The main deficiency of utilization are in decision support systems and external integration functions. Suggestions are presented for increasing effectiveness of IT use in business process

Frequency of metabolic syndrome and its components in 300 Pakistani obese patients

International Nuclear Information System (INIS)

Khattak, I.; Ishaq, T.; Fida, Z.; Rehman, F.U.

2017-01-01

To assess the frequency of metabolic syndrome (MS) and its constituents in a sample of Pakistani obese patients. Methodology: In this descriptive and cross-sectional study, we used a sample of 300 patients from Khyber Teaching Hospital, Peshawar, Pakistan from April 2016 to November 2016. They were randomly selected and their mean age was between 15 and 25 years. The variables obtained included BMI, both systolic and diastolic blood pressure, cholesterol, fasting blood glucose, triglyceride levels, LDL- cholesterol, HDL-cholesterol, waist to hip ratio, waist circumference and insulin resistance. Results: Of the 300 patients, the frequency of MS was 20%. There were no significant differences in the frequency of developing MS between the genders. The order of frequency of the components as observed was as follows; abdominal obesity was 88%, high triglyceride level was 85%, males were 40%, 40% of the sampled population resided in the urban area. Meanwhile, 35% of the patients had hypertension while only 5% had hyperglycemia. The frequency of developing MS was 70 times higher in patients with high triglyceride levels in their when compared to those with normal levels. Conclusion: The frequency of MS and its components in Pakistani adolescent patients is high. The high levels of triglyceride and a sedentary lifestyle profoundly contributed to MS. Moreover, the findings signify the importance of early treatment and prevention of obesity in working toward reducing the rate of diabetes mellitus type 2; as glucose intolerance had a strong relationship with the components of MS, and cardiovascular diseases such coronary artery disease. (author)

The world behind electricity from coal. The dubious origin of coal for Dutch coal-fired power plants

International Nuclear Information System (INIS)

2008-01-01

Five energy companies in the Netherlands want to build additional coal-fired power plants: Essent and Nuon, the German company RWE and E.ON and the Belgian company Electrabel. Coal-fired power plants emit 70 percent more CO2 than gas-fired power plants. Especially because of the threat to the climate Greenpeace believes that no more coal-fired power plants should be built. In this publication Greenpeace explores the pollution, the working conditions and human rights with regard to the exploitation of coal. That has been elaborated for the three countries from which Dutch energy companies import coal: South Africa, Colombia and Indonesia. In addition to information about the origin of coal also insight is given into the coal market (stocks and use), the enormous coal transport and the world trade [nl

Food perceptions in terms of health among Norwegian-Pakistani women participating in a culturally adapted intervention.

Science.gov (United States)

Råberg Kjøllesdal, Marte Karoline; Hjellset, Victoria Telle; Bjørge, Benedikte; Holmboe-Ottesen, Gerd; Wandel, Margareta

2011-10-01

To explore food perceptions in terms of health among Pakistani immigrant women, and if such perceptions could be altered through a culturally adapted intervention. The study is a culturally adapted lifestyle intervention aiming at reducing diabetes risk among Pakistani women, Oslo, Norway. There were 198 participants (25-62 years) recruited through a multi-recruitment strategy and randomly assigned into intervention and control groups. Data were collected through interviews with the help of a structured questionnaire with open-ended questions. Baseline data showed that many women emphasised vegetables (87%) and fish (52%) as important in a healthy diet, and perceived that the consumption of sugar (66%), oil (60%) and hard fat (39%) should be limited. After intervention, there was an increased proportion of women in the intervention group who perceived that consumption of sugar (p = 0.021) and white flour (p = 0.010) should be limited, in line with the emphasis of the intervention. Food perceptions in terms of health were generally in line with public dietary advice, however, with large variation among the women. A culturally adapted intervention had the potential to alter such perceptions.

Content and distribution of fluorine in rock, clay and water in fluorosis area Zhaotong, Yunnan Province

Energy Technology Data Exchange (ETDEWEB)

Luo, K.; Li, H.; Feng, F. (and others) [Chinese Academy of Sciences, Beijing (China)

2007-04-15

About 160 samples of coal, pyritic coal balls, coal seam gangue, clay, corn, capsicum and drinking water were collected from the endemic fluorosis area of Zhenxiong and Weixin county, China to determine the fluorine content, distribution pattern and source in this fluorosis area. The study shows that the average fluorine content in the coal samples collected from 3 coal mines of the Late Permian coals in Zhenxiong and Weixin county, Zhaotong City, which are the main mining coals there, is 77.13 mg/kg. The average fluorine content coals collected form thee typical fluorosis villages in 72.56 mg/kg. Both of them are close to the world average and little low than the Chinese average. The fluorine content of drinking water is lower than 0.35 mg/L, the clay used as an additive for coal-burning and as a binfer in briquette-making by local residents has a high content of fluorine, ranging from 367-2,435 mg/kg, with the majority higher than 600 mg/kg and an average of 1,084.2 mg/kg. 29 refs., 5 tabs.

Important TQM Implementation Contributors in Pakistani Petrochemical Sector

Directory of Open Access Journals (Sweden)

Yasir Latif

2014-10-01

Full Text Available This study discusses quality practices in Pakistani Petrochemical sector to understand TQM practices and their implementation in Pakistan. It helps to understand the role of leadership, vision & plan statement, employee participation and education & training as important constructs of TQM. It shows how these constructs help to speed up the TQM implementation in petrochemical sector like other constructs of TQM and finally company moves towards quality approach. The responses of executives, managerial staff and workers were received using questionnaire and online surveys which are sent through Google Drive. Data of 106 respondents was taken in this study and analyzed by SPSS18. Study shows that Total Quality Management culture is less understood by employees, thus less adopted and implemented in Pakistan. Petrochemical companies fail to adopt the TQM philosophy and processes, hence reducing productivity and profits. This research paper is very helpful for executives for TQM implementation in petrochemical sector.

Barriers to healthy eating among Norwegian-Pakistani women participating in a culturally adapted intervention.

Science.gov (United States)

Råberg Kjøllesdal, Marte K; Telle Hjellset, Victoria; Bjørge, Benedikte; Holmboe-Ottesen, Gerd; Wandel, Margareta

2010-11-01

To explore barriers to healthy dietary changes experienced by Pakistani immigrant women participating in a culturally adapted intervention, and whether these barriers were associated with intentions to change dietary behaviours. Participants were randomly assigned to control and intervention group. The 7-month intervention consisted of six educational group sessions on diet and physical activity, based on knowledge about Pakistani lifestyle and focusing on blood glucose control. Data on barriers for and intentions to healthy dietary changes were collected through an interview with help of a questionnaire. The article is based on data from follow-up assessments in the intervention group, comprising 82 women, aged 28-62 years, without a history of type 2 diabetes. The most important barriers to healthy dietary changes were preferences of children and other family members and perceived expectations during social gatherings. The perceived pressure from other family members was especially strong when the women were trying to change to more vegetables, lentils, and fish and to use less oil in food preparation. The barriers were inversely related to intentions to change. The women encountered various types of barriers when trying to change to healthier food habits, the most prominent being those related to the social dimensions of food consumption, as well as to awareness of the amount of oil used for cooking.

Coal information 1995

International Nuclear Information System (INIS)

1996-01-01

This volume is a comprehensive reference book on current world coal market trends and long-term prospects to 2010. It contains an in-depth analysis of the 1995 international coal market covering prices, demand, trade, supply and production capacity as well as over 450 pages of country specific statistics on OECD and key non-OECD coal producing and consuming countries. The book also includes a summary of environmental policies on climate change and on coal-related air quality issues as well as essential facts on coal-fired power stations in coal-importing regions, on coal ports world-wide and on emission standards for coal-fired boilers in OECD countries. Coal Information is one of a series of annual IEA statistical publications on major energy sources; other reports are Oil and Gas Information and Electricity Information. Coal Information 1995 is published in July 1996. (author)

The clean coal technologies for lignitic coal power generation in Pakistan

International Nuclear Information System (INIS)

Mir, S.; Raza, Z.; Aziz-ur-Rehman, A.

1995-01-01

Pakistan contains huge reserves of lignitic coals. These are high sulphur, high ash coals. In spite of this unfortunate situation, the heavy demand for energy production, requires the development utilization of these indigenous coal reserves to enhance energy production. The central of the environmental pollution caused by the combustion of these coals has been a major hindrance in their utilization. Recently a substantial reduction in coal combustion emissions have been achieved through the development of clean coal technologies. Pakistan through the transfer and adaptation of the advanced clean coal technologies can utilize incurring the high sulphur coals for energy production without incurring the environmental effects that the developed countries have experienced in the past. The author discusses the recently developed clean coal utilization technologies, their applications economies and feasibility of utilization with specific reference to Pakistan''s coal. (author)

Coal information 1996

International Nuclear Information System (INIS)

1997-01-01

Coal Information (1997 edition) is the latest edition of a publication that has been produced annually by the IEA since 1983. The report is intended to provide both Member countries of the OECD and those employed in all sectors of the coal industry with information on current world coal market trends and long-term prospects. It includes information on coal prices, demand, trade, supply, production capacity, transport, environmental issues (including emission standards for coal-fired boilers), coal ports, coal-fired power stations and coal used in non -OECD countries. Part I of the publication contains a wide ranging review of world coal market developments in 1996 and current prospects to 2010. The review is based on historical data of OECD energy supply and demand, data on other world regions, projections of OECD coal supply, demand and trade and information provided by the CIAB. Part II provides, in tabular and graphical form, a more detailed and comprehensive statistical picture of coal developments and future prospects for coal in the OECD, by region and for individual Member countries. Readers interested in projections are strongly advised to read the notes for individual countries in Principles and Definitions in Part II. Coal statistics for non-OECD countries are presented in Part III of the book. Summary data are available on hard coal supply and end-use statistics for about 40 countries and regions world-wide. Data are based on official national submissions to the United Nations in Geneva and New York, national energy publications, information provided to the IEA Secretariat by national statistical offices as well as other unofficial Secretariat sources. Further information on coal used in non-OECD countries is published annually by the IEA in Energy Statistics and Balances of Non-OECD Countries. Also included in Part III are the Survey of Coal Ports world-wide and the Survey of Coal-fired Power Stations in coal-importing countries

Analysis of the economic viability of the briquette production in the Brazilian market; Analise da viabilidade economica da producao de briquetes no mercado brasileiro

Energy Technology Data Exchange (ETDEWEB)

Almeida, Silvio Carlos Anibal de [Universidade Federal do Rio de Janeiro (DEM/EP/UFRJ), RJ (Brazil). Escola Politecnica. Dept. de Engenharia Mecanica], E-mail: silvioa@gmail.com; Barbosa, Bruno de Luca Lima; Souza, Julia do Rego Mello Fernandes de; Monteiro, Paulo Victor da Conceicao; Gomes, Thiago de Carvalho [Universidade Federal do Rio de Janeiro (DEI/CT/UFRJ), RJ (Brazil). Dept. de Engenharia Industrial], E-mail: brunodeluca@poli.ufrj.br

2010-07-01

This paper presents a study of economic viability of a 3 ton/hour briquette industry. For establish of study, premises such as costs, investments, prices at Brazilian and european markets and growing of sector forecast were established according to criteria defined by the authors. Two scenarios were considered: investors which hold all the capital necessary for the business and investors which need of a financing for realization of the enterprise. For the second scenery considering a certain interest rate and a mode of financing. Both scenery revealed profitable for the investor.

Coal industry annual 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

Coal industry annual 1997

International Nuclear Information System (INIS)

1998-12-01

Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs

Phyto-bioconversion of hard coal in the Cynodon dactylon/coal rhizosphere.

Science.gov (United States)

Igbinigie, Eric E; Mutambanengwe, Cecil C Z; Rose, Peter D

2010-03-01

Fundamental processes involved in the microbial degradation of coal and its derivatives have been well documented. A mutualistic interaction between plant roots and certain microorganisms to aid growth of plants such as Cynodon dactylon (Bermuda grass) on hard coal dumps has recently been suggested. In the present study coal bioconversion activity of nonmycorrhizal fungi was investigated in the C. dactylon/coal rhizosphere. Fungal growth on 2% Duff-agar, gutation formation on nitric acid treated coal and submerged culture activity in nitrogen-rich and -deficient broth formed part of the screening and selection of the fungi. The selected fungal isolates were confirmed to be found in pristine C. dactylon/coal rhizosphere. To simulate bioconversion, a fungal aliquot of this rhizosphere was used as inoculum for a Perfusate fixed bed bioreactor, packed with coal. The results demonstrate an enhanced coal bioconversion facilitated by low molecular weight organics and the bioconversion of coal may be initiated by an introduction of nitrogen moieties to the coal substrate. These findings suggest a phyto-bioconversion of hard coal involving plant and microbes occurring in the rhizosphere to promote the growth of C. dactylon. An understanding of this relationship can serve as a benchmark for coal dumps rehabilitation as well as for the industrial scale bioprocessing of hard coal.

Slagging behavior of upgraded brown coal and bituminous coal in 145 MW practical coal combustion boiler

Energy Technology Data Exchange (ETDEWEB)

Akiyama, Katsuya; Pak, Haeyang; Takubo, Yoji [Kobe Steel, Ltd, Kobe (Japan). Mechanical Engineering Research Lab.; Tada, Toshiya [Kobe Steel, Ltd, Takasago (Japan). Coal and Energy Technology Dept.; Ueki, Yasuaki [Nagoya Univ. (Japan). Energy Science Div.; Yoshiie, Ryo; Naruse, Ichiro [Nagoya Univ. (Japan). Dept. of Mechanical Science and Engineering

2013-07-01

The purpose of this study is to quantitatively evaluate behaviors of ash deposition during combustion of Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. A blended coal consisting 20 wt% of the UBC and 80 wt% of the bituminous coal was burned for the combustion tests. Before the actual ash deposition tests, the molten slag fractions of ash calculated by chemical equilibrium calculations under the combustion condition was adopted as one of the indices to estimate the tendency of ash deposition. The calculation results showed that the molten slag fraction for UBC ash reached approximately 90% at 1,523 K. However, that for the blended coal ash became about 50%. These calculation results mean that blending the UBC with a bituminous coal played a role in decreasing the molten slag fraction. Next, the ash deposition tests were conducted, using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at 1,523 K in the boiler to measure the amount of ash deposits. The results showed that the mass of deposited ash for the blended coal increased and shape of the deposited ash particles on the tube became large and spherical. This is because the molten slag fraction in ash for the blended coal at 1,523 K increased and the surface of deposited ash became sticky. However, the mass of the deposited ash for the blended coal did not greatly increase and no slagging problems occurred for 8 days of boiler operation under the present blending conditions. Therefore, appropriate blending of the UBC with a bituminous coal enables the UBC to be used with a low ash melting point without any ash deposition problems in a practical boiler.

Modernism and Postmodernism: A Study of the Islamic Teachings with Special Reference to the Related Issues of Pakistani Society

Directory of Open Access Journals (Sweden)

Dr. Abdul Muhaimin

2017-02-01

Full Text Available Abstract This study elaborates the difference and connection between modernism and postmodernism eras while highlighting their backgrounds. The research highlights the teachings of Islam in terms of modernism and postmodernism. The research brings to light the influence of modernism and postmodernism on Muslim societies. What are the far reaching impacts of the modernism and postmodernism eras of Muslim societies and how well a common Muslim is equipped to address the issues related to postmodernism. The study primarily focuses on the related issues in Pakistani society and explains the role and the influence of religious scholars of their understanding of the terms modernism and postmodernism. The study focuses on the awareness of the ’Ulamā in addressing these global challenges and subsequently the future of Pakistani society. The study has an element of quantitative research and it indicates towards the on ground realities on the issue with the help of a latest survey on modernism and postmodernism.

Coal yearbook 1993

International Nuclear Information System (INIS)

Anon.

1993-01-01

This book is the first coal yearbook published by ATIC (France). In a first chapter, economical context of coal worldwide market is analyzed: comparative evaluations on coal exports and imports, coal industry, prices, production in USA, Australia, South Africa, China, former USSR, Poland, Colombia, Venezuela and Indonesia are given. The second chapter describes the french energy context: national coal production, imports, sectorial analysis, maritime transport. The third chapter describes briefly the technologies of clean coal and energy saving developed by Charbonnages de France: fossil-fuel power plants with combined cycles and cogeneration, fluidized beds for the recovery of coal residues, recycling of agricultural wastes (sugar cane wastes) in thermal power plant, coal desulfurization for air pollution abatement. In the last chapter, statistical data on coal, natural gas and crude oil are offered: world production, world imports, world exports, french imports, deliveries to France, coal balance, french consumption of primary energy, power generation by fuel type

First COSTECH scientific and technological conference: Science and technology for growth and poverty reduction in Tanzania

International Nuclear Information System (INIS)

Mushi, S.J.S.; Raphael, L.M.

2006-01-01

Due to high rate of deforestation and environmental degradation caused by felling of trees for fuel, it is imperative that alternative energy resources be sought and exploited. This country, is rich in coal reserves estimated at 1.2 -1.9 billion tonnes, enough to serve the country for many years to come, but coal usage for domestic purposes i.e, cooking and crop drying is still not common in this country and therefore efforts are needed to promote its utilization. The paper discusses the problem of fuel wood use in Tanzania and the efforts made so far to develop the capacity for coal utilization as an alternative fuel to fuel wood. In addition, the paper highlights the experiences of formulating entrepreneurship in developing coal- biomass briquettes as a technology transfer model. The production and tests carried out on coal-biomass utilization technology, has shown that there is a breakthrough and potential for coal biomass utilization at domestic and institutional levels in Tanzania.(author)

CO2 Problems and waste recycling. Research at the Institute of ferrous metallurgy

International Nuclear Information System (INIS)

Gudenau, H. W.; Senk, D.; Babich, A.; Frohling, C.; Kweon, O. S.; Wang, S.; Wieting, T.

2005-01-01

In a short introduction tests and calculations about CO 2 -ice-blocs in the deep sea,use of CO 2 for underground-coal-gasifications and tertiary processes to increase oil-production by CO 2 -flooding are shown. New activities are presented e. g. CO 2 -injection into EAF combined with injection of coal, coke or direct reduction-fines. After research of injection of coals, fine ores or dust into blast furnaces and other shaft furnaces activities are compared with injection of hot reducing gas generated by coal or waste gasification or top gas recycling combined with injection of fine solid fuels. Results of injection of prepared plastics (Duales System Deutschland), shredder-light-fraction from car-recycling and unburned carbon of power-station-ashes are discussed. Beside production of direct-reduced-iron by H 2 fluidized reactor results of the reduction behaviour ore/coal or dust/coal pellets or briquettes for the use in rotary hearth or modern shaft furnaces are shown. (Author) 76 refs

Prospects for coal and clean coal technology in the Philippines

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-03-15

This report examines the current energy outlook for the Philippines in regard not only to coal but also other energy resources. The history of the power sector, current state of play and future plans to meet the increasing energy demand from a growing population are discussed. There is also analysis of the trends for coal demand and production, imports and exports of coal and the types of coal-fired power stations that have been built. This includes examination of the legislation involving coal and the promotion of clean coal technologies.

Rosebud SynCoal Partnership, SynCoal{reg_sign} demonstration technology update

Energy Technology Data Exchange (ETDEWEB)

Sheldon, R.W. [Rosebud SynCoal Partnership, Billings, MT (United States)

1997-12-31

An Advanced Coal Conversion Process (ACCP) technology being demonstrated in eastern Montana (USA) at the heart of one of the world`s largest coal deposits is providing evidence that the molecular structure of low-rank coals can be altered successfully to produce a unique product for a variety of utility and industrial applications. The product is called SynCoal{reg_sign} and the process has been developed by the Rosebud SynCoal Partnership (RSCP) through the US Department of Energy`s multi-million dollar Clean Coal Technology Program. The ACCP demonstration process uses low-pressure, superheated gases to process coal in vibrating fluidized beds. Two vibratory fluidized processing stages are used to heat and convert the coal. This is followed by a water spray quench and a vibratory fluidized stage to cool the coal. Pneumatic separators remove the solid impurities from the dried coal. There are three major steps to the SynCoal{reg_sign} process: (1) thermal treatment of the coal in an inert atmosphere, (2) inert gas cooling of the hot coal, and (3) removal of ash minerals. When operated continuously, the demonstration plant produces over 1,000 tons per day (up to 300,000 tons per year) of SynCoal{reg_sign} with a 2% moisture content, approximately 11,800b Btu/lb and less than 1.0 pound of SO{sub 2} per million Btu. This product is obtained from Rosebud Mine sub-bituminous coal which starts with 25% moisture, 8,600 Btu/lb and approximately 1.6 pounds of SO{sub 2} per million Btu.

Genome-Wide Supported Risk Variants in MIR137, CACNA1C, CSMD1, DRD2, and GRM3 Contribute to Schizophrenia Susceptibility in Pakistani Population.

Science.gov (United States)

Fatima, Ambrin; Farooq, Muhammad; Abdullah, Uzma; Tariq, Muhammad; Mustafa, Tanveer; Iqbal, Muhammad; Tommerup, Niels; Mahmood Baig, Shahid

2017-09-01

Schizophrenia is a chronic neuropsychiatric disease afflicting around 1.1% of the population worldwide. Recently, MIR137 , CACNA1C , CSMD1 , DRD2 , and GRM3 have been reported as the most robustly emerging candidates involved in the etiology of schizophrenia. In this case control study, we performed an association analysis of rs1625579 ( MIR137 ), rs1006737, rs4765905 ( CACNA1C ), rs10503253 ( CSMD1 ), rs1076560 ( DRD2 ), rs12704290, rs6465084, and rs148754219 ( GRM3 ) in Pakistani population. Schizophrenia was diagnosed on the basis of the Diagnostic and Statistical Manual of Mental Disorders 4th ed (DSM-IV). Detailed clinical information, family history of all patients and healthy controls were collected. RFLP based case control association study was performed in a Pakistani cohort of 508 schizophrenia patients and 300 healthy control subjects. Alleles and genotype frequencies were calculated using SPSS. A significant difference in the genotype and allele frequencies for rs4765905, rs1076560 and rs6465084 were found between the patients and controls (p=0.000). This study provides substantial evidence supporting the role of CACNA1C , GRM3 and DRD2 as schizophrenia susceptibility genes in Pakistani population.

Self-scrubbing coal

International Nuclear Information System (INIS)

Kindig, J.K.

1992-01-01

More than 502 million tons - 65 percent of all coal shipped to utilities in 1990 - were above 1.2 pounds of sulfur dioxide per million Btu. Most of the coal, even though cleaned in conventional coal preparation plants, still does not meet the emission limitation the Clean Air Act Amendments mandate for the year 2000. To cope with this fact, most utilities plan to switch to low sulfur (western U.S. or Central Appalachian) coal or install scrubbers. Both solutions have serous drawbacks. Switching puts local miners out of work and weakens the economy in the utility's service territory. Scrubbing requires a major capital expenditure by the utility. Scrubbers also increase the operating complexity and costs of the generating station and produce yet another environmental problem, scrubber sludge. Employing three new cost-effective technologies developed by Customer Coals International (CCl), most non-compliance coals east of the Mississippi River can be brought into year-2000 compliance. The compliance approach employed, depends upon the characteristics of the raw coal. Three types of raw coal are differentiated, based upon the amount of organic sulfur in the coals and the ease (or difficultly) of liberating the pyrite. They are: Low organic sulfur content and pyrite that liberates easily. Moderate organic sulfur content and pyrite that liberates easily. High organic sulfur content or the pyrite liberates with difficulty. In this paper examples of each type of raw coal are presented below, and the compliance approach employed for each is described. The names of the beneficiated coal products produced from each type of raw coal give above are: Carefree Coal, Self-Scrubbing Coal and Dry-Scrubbing Coal

The application of the coal grain analysis method to coal liberation studies

Energy Technology Data Exchange (ETDEWEB)

O' Brien, G.; Firth, B.; Adair, B. [CSIRO Earth Science & Resource Engineering Brisbane, Qld. (Australia)

2011-07-01

Emerging coal markets such as the use of coal for conversion to liquid fuels and its use in fuels cells and as coal water slurries in diesel engines require coal products with different coal quality specifications than those applicable to traditional coal markets of coke making and conventional power generation. As well as quantifying coals in terms of their chemical and physical properties, detailed knowledge of the mineral inclusions within the coal particles is required to identify coals that are suited to economically produce the low-ash value coals required for these markets. After mining and processing, some particles can consist of essentially pure components of a single maceral or mineral phase whilst others are composite particles that are comprised of varying amounts of macerals and minerals. The proportion of particles that are present as pure components or as composites will be a function of the characteristics of the coal and the particle size. In general, it is considered that size reduction will result in liberation and hence increased yield. The amount of liberation that occurs during crushing or grinding a coal is however coal specific. Particle characterization information provided by an optical microscopic-imaging method, Coal Grain Analysis, was used to identify coals that might benefit from additional crushing to improve recovery of clean coal by new density separation techniques and by flotation. As expected, the results of these studies suggest that the degree of liberation that is obtained is coal specific, and, hence, yield improvements are also coal specific. Hence a quantitative method of investigating this issue is required.

Third symposium on coal preparation. NCA/BCR coal conference and Expo IV

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-01

The third Symposium on Coal preparation, sponsored by the National Coal Association and Bituminous Coal Research, Inc., was held at the Kentucky Fair and Exposition Center, Louisville, Kentucky, October 18-20, 1977. Fourteen papers from the proceedings have been entered individually into EDB and ERA; five additional papers had been entered previously from other sources. Topics covered involved chemical comminution and chemical desulfurization of coal (aimed at reducing sulfur sufficiently with some coals to meet air quality standards without flue gas desulfurization), coal cleaning concepts, removing coal fines and recycling wash water, comparative evaluation of coal preparation methods, coal refuse disposal without polluting the environment, spoil bank reprocessing, noise control in coal preparation plants, etc. (LTN)

Coal industry annual 1993

Energy Technology Data Exchange (ETDEWEB)

1994-12-06

Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993.

Coal industry annual 1993

International Nuclear Information System (INIS)

1994-01-01

Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993

Alcohol and marijuana use while driving--an unexpected crash risk in Pakistani commercial drivers: a cross-sectional survey.

Science.gov (United States)

Mir, Mohammed Umer; Khan, Imran; Ahmed, Bilal; Abdul Razzak, Junaid

2012-02-27

A significant proportion of road traffic crashes are attributable to alcohol and marijuana use while driving globally. Sale and use of both substances is illegal in Pakistan and is not considered a threat for road traffic injuries. However literature hints that this may not be the case. We did this study to assess usage of alcohol and marijuana in Pakistani commercial drivers. A sample of 857 commercial bus and truck drivers was interviewed in October 2008 at the largest commercial vehicle station in Rawalpindi and Islamabad, Pakistan. Time location cluster sampling was used to select the subjects and a structured questionnaire was used to assess the basic demographic profile, substance abuse habits of the drivers while on the road, and reasons for usage of illicit substances while driving were recorded. Self reported information was collected after obtaining informed consent. Chi square and fisher exact tests were used to assess differences between groups and logistic regression was used to identify significant associations between driver characteristics and alcohol and marijuana use. Almost 10% of truck drivers use alcohol while driving on Pakistani roads. Marijuana use is almost 30% in some groups. Statistically different patterns of usage are seen between population subgroups based on age, ethnicity, education, and marital status. Regression analysis shows association of alcohol and marijuana use with road rage and error behaviours, and also with an increased risk of being involved in road crashes. The reported reasons for using alcohol or marijuana show a general lack of awareness of the hazardous nature of this practice among the commercial driver population. Alcohol and marijuana use is highly prevalent in Pakistani commercial drivers. The issue needs to be recognized by concerned authorities and methods such as random breath tests and sobriety check points need to be employed for proper law enforcement.

Barriers and facilitators to cervical cancer screening among Pakistani and Somali immigrant women in Oslo: a qualitative study.

Science.gov (United States)

Gele, Abdi A; Qureshi, Samera A; Kour, Prabhjot; Kumar, Bernadette; Diaz, Esperanza

2017-01-01

Norway has a low incidence and mortality rate of cervical cancer, which is mainly due to the high participation rate of women in cervical cancer screening. However, the attendance of cervical cancer screening was reported to be low among immigrant women. For this reason, we conducted a qualitative study to obtain better insight into perceived barriers and challenges to cervical cancer screening among Somali and Pakistani women in the Oslo region. A convenient sample of 35 (18 Pakistani, 17 Somali) women were recruited for the study in collaboration with Somali and Pakistani community partners. Focus group discussions were used to explore barriers and facilitators to cervical cancer screening, whereas the Ecological Model was used as the framework for the study. The study found three levels of barriers to cervical cancer screening. The individual level included a lack of understanding of the benefits of the screening. The sociocultural level included the stigma attached to the disease and the belief that women who are unmarried are sexually inactive. The system-related level included a lack of trust toward the health care system. Based on the study results, and using a common denominator approach for the immigrant groups included, the study recommends three communication strategies with the potential to improve women's participation in cervical cancer screening: 1) in-person communication and information material at health centers; 2) verbal communication with women through seminars and workshops to educate them about their risk of cancer and the importance of screening and 3) the initiation of better recall through SMS and letters written in native languages. Finally, an intervention study that compares the aforementioned strategies and proves their effectiveness in increasing immigrant women's participation in cervical cancer screening is recommended.

Alcohol and marijuana use while driving--an unexpected crash risk in Pakistani commercial drivers: a cross-sectional survey

Directory of Open Access Journals (Sweden)

Mir Mohammed

2012-02-01

Full Text Available Abstract Background A significant proportion of road traffic crashes are attributable to alcohol and marijuana use while driving globally. Sale and use of both substances is illegal in Pakistan and is not considered a threat for road traffic injuries. However literature hints that this may not be the case. We did this study to assess usage of alcohol and marijuana in Pakistani commercial drivers. Methods A sample of 857 commercial bus and truck drivers was interviewed in October 2008 at the largest commercial vehicle station in Rawalpindi and Islamabad, Pakistan. Time location cluster sampling was used to select the subjects and a structured questionnaire was used to assess the basic demographic profile, substance abuse habits of the drivers while on the road, and reasons for usage of illicit substances while driving were recorded. Self reported information was collected after obtaining informed consent. Chi square and fisher exact tests were used to assess differences between groups and logistic regression was used to identify significant associations between driver characteristics and alcohol and marijuana use. Results Almost 10% of truck drivers use alcohol while driving on Pakistani roads. Marijuana use is almost 30% in some groups. Statistically different patterns of usage are seen between population subgroups based on age, ethnicity, education, and marital status. Regression analysis shows association of alcohol and marijuana use with road rage and error behaviours, and also with an increased risk of being involved in road crashes. The reported reasons for using alcohol or marijuana show a general lack of awareness of the hazardous nature of this practice among the commercial driver population. Conclusion Alcohol and marijuana use is highly prevalent in Pakistani commercial drivers. The issue needs to be recognized by concerned authorities and methods such as random breath tests and sobriety check points need to be employed for proper law

The midwife-woman relationship in a South Wales community: Experiences of midwives and migrant Pakistani women in early pregnancy.

Science.gov (United States)

Goodwin, Laura; Hunter, Billie; Jones, Aled

2018-02-01

In 2015, 27.5% of births in England and Wales were to mothers born outside of the UK. Compared to their White British peers, minority ethnic and migrant women are at a significantly higher risk of maternal and perinatal mortality, along with lower maternity care satisfaction. Existing literature highlights the importance of midwife-woman relationships in care satisfaction and pregnancy outcomes; however, little research has explored midwife-woman relationships for migrant and minority ethnic women in the UK. A focused ethnography was conducted in South Wales, UK, including semi-structured interviews with 9 migrant Pakistani participants and 11 practising midwives, fieldwork in the local migrant Pakistani community and local maternity services, observations of antenatal appointments, and reviews of relevant media. Thematic data analysis was undertaken concurrently with data collection. The midwife-woman relationship was important for participants' experiences of care. Numerous social and ecological factors influenced this relationship, including family relationships, culture and religion, differing health-care systems, authoritative knowledge and communication of information. Marked differences were seen between midwives and women in the perceived importance of these factors. Findings provide new theoretical insights into the complex factors contributing to the health-care expectations of pregnant migrant Pakistani women in the UK. These findings may be used to create meaningful dialogue between women and midwives, encourage women's involvement in decisions about their health care and facilitate future midwifery education and research. Conclusions are relevant to a broad international audience, as achieving better outcomes for migrant and ethnic minority communities is of global concern. © 2017 The Authors Health Expectations Published by John Wiley & Sons Ltd.

Coal and Energy.

Science.gov (United States)

Bryant, Reba; And Others

This teaching unit explores coal as an energy resource. Goals, student objectives, background information, and activity options are presented for each major section. The sections are: (1) an introduction to coal (which describes how and where coal was formed and explains the types of coal); (2) the mining of coal (including the methods and ways of…

Cooperative Monitoring Center Occasional Paper/6: Pakistani Perceptions and Prospects of Reducing the Nuclear Danger in South Asia

Energy Technology Data Exchange (ETDEWEB)

Kamal, N.

1999-01-01

The Indian and Pakistani nuclear tests in May 1998 triggered a full-blown nuclear debate. For the first time, hard-liners, moderates, and pacifists engaged in an extensive public discussion that helped to make the people of Pakistan more sensitive to the dangers of nuclear competition. Pakistan's concerns about its conventional military inferiority, both in the present and future, and the belief that nuclear capability would deter India from exerting its superior military strength, constituted the bedrock of its perception on the nuclear issue. Ofilcial Pakistani statements, both immediately after the nuclear tests and later, have advocated restraint on the issue of nuclearization, indicating cognizance of the importance of avoiding a regional nuclear arms competition, both for security and economic reasons. This paper suggests a variety of nonweaponization and nondeployment options that would serve the security interests of India and Pakistan. Besides preventing a hair-trigger situation, these options could reduce the financial and logistical burden of ensuring the safety and security of nuclear weapons as well as lower strategic threat-perceptions.

Asia's coal and clean coal technology market potential

International Nuclear Information System (INIS)

Johnson, C.J.; Binsheng Li

1992-01-01

The Asian region is unique in the world in having the highest economic growth rate, the highest share of coal in total primary energy consumption and the highest growth rate in electricity generation capacity. The outlook for the next two decades is for accelerated efforts to control coal related emissions of particulates and SO 2 and to a lessor extent NO x and CO 2 . Only Japan has widespread use of Clean Coal Technologies (CCTs) however a number of economies have plans to install CCTs in future power plants. Only CCTs for electricity generation are discussed, and are defined for the purpose of this paper as technologies that substantially reduce SO 2 and/or NO x emissions from coal-fired power plants. The main theses of this paper are that major increases in coal consumption will occur over the 1990-2010 period, and this will be caccompanied by major increases in coal related pollution in some Asian economies. Coal fired electricity generation is projected to grow at a high rate of about 6.9 percent per year over the 1990-2010 period. CCTs are projected to account for about 150 GW of new coal-fired capacity over the 1990-2010 period of about one-third of all new coal-fired capacity. A speculative conclusion is that China will account for the largest share of CCT additions over the 1990-2010 period. Both the US and Japan have comparative advantages that might be combined through cooperation and joint ventures to gain a larger share of the evolving CCT market in Asia. 5 refs., 7 figs., 4 tabs

Coal - 96

International Nuclear Information System (INIS)

Sparre, C.

1996-09-01

The report deals mainly with coal consumption, but also gives some information about technology, environmental aspects and markets. Data have been collected by questionnaires or via telephone. The use of steam coal for heating was 0.8 Mtons (down 20% from 1994). Cogeneration plants were the main users. Taxes and environmental reasons cause a reduction of the coal use that will probably continue the next years. Use of steam coal in industry has been constant at a level of 0.7 Mtons. The import of metallurgical coal rests constant at a level of 1.6 Mtons. 1.2 Mtons of coke was produced, and 0.3 Mtons imported. The PFBC-plant at Vaertan, Stockholm used 0.13 Mtons of coal, while some coal fired power plants have been converted to peat and wood fuels. The average price of steam coal imported to Sweden in 1995 was 333 SEK/ton, 6% higher than in 1994. The contract prices for delivery 1996 are about the same as at the end of 1995. All cogeneration plants have some sort of SO 2 removal system, mostly wet-dry. The largest plant, at Vaesteraas, has recently invested in a SCR system for NO x removal. Most other plants are using low NO x burners or SNCR systems, based on ammonia or urea, which reduce the emissions 50 - 70%. Some statistic about the world coal market is also given in the report

Swelling behavior of several bituminous coals and their thermally treated coals

Energy Technology Data Exchange (ETDEWEB)

Shui, Heng-fu; Cao, Mei-xia; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry & Chemical Engineering

2007-07-01

The swelling behavior in different solvents of 4 bituminous coals with different ranks and their residues from extraction by CS{sub 2}/NMP mixed solvent (l:1 in volume) were measured. The change in swelling property of the four coals thermally treated at different temperature was observed. The results show that the swelling ratio decreases with increasing rank of coal. For lower rank bituminous coals the swelling ratios in polar solvent are higher than those in non-polar solvent, and this difference decreases with increasing rank. The cross-linking densities of the four residues decrease, and the swelling ratios increase compared with those of raw coals. The swelling ratios of the four thermally treated coals under 150{sup o}C in CS{sub 2} increase, suggesting the decrease in crosslinking density of them. When the thermal treatment temperature increases to 240{sup o}C, the swelling rations of the other three coals in NMP and CS{sub 2} increase again except gas coal, demonstrating the further decrease in crosslinking density. This result is coincident with the extraction yield change in the mixed solvent of the thermally treated coal. For example, the extraction yield of lean coal treated at 240{sup o}C increases from 6.9% to 17.3%. FT-IR results show the removal of oxygen group of the thermally treated coals. This may explain the increase in swelling ratio and extraction yield in the mixed solvent of coal after thermal treatment. The cross-linking density of the thermally treated coal decreases because of the break of hydrogen bonds due to removal of C = 0 and -OH oxygen groups during the thermal treatment, resulting in the increases of swelling ratio and extraction yield in the mixed solvent of thermally treated coal compared with those of raw coal. 15 refs., 3 figs., 6 tabs.

Proceedings of the sixth APEC Coal Flow Seminar. Coal in the new millennium

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

The 6th APEC Coal Flow Seminar titled on 'The coal in the new millennium' was held in Korea from March 14 to March 16, 2000, and the proceedings were summed up. In this seminar, as to economies of coal consumption countries and coal supply countries in the APEC region, discussions were made on coal supply/demand, coal price, environmental problems and others. The keynote address was 'Twenty first century coal in the APEC region and Republic of Korea' given by Mr. Gam Yeol Lee from Korea. The main theme of the seminar was 'The status quo for the coal market,' and lectures titled on the following were given from Japan: 'The status quo of coal purchase by the Japanese electric company and its outlook' and 'A perspective of coal fired IPP under environmental constraints and deregulation of electricity.' Lectures from Australia: 'Responding to coal market growth in APEC regions by the Australian coal industry' and 'The coal price impact on coal supply and demand.' Further discussions were made on 'The long-term outlook for coal supply/demand' and 'Economies report on the outlook for coal supply/demand.' (NEDO)

Coal industry annual 1996

International Nuclear Information System (INIS)

1997-11-01

This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs

Coal industry annual 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs.

Coal Industry Annual 1995

International Nuclear Information System (INIS)

1996-10-01

This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995

Coal Industry Annual 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-01

This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995.

South Blackwater Coal`s maintenance program

Energy Technology Data Exchange (ETDEWEB)

Nash, J. [South Blackwater Coal Limited, Blackwater, Qld. (Australia)

1998-09-01

The South Blackwater operation consists of two opencut mining areas and two underground mines (Laleham and Kenmure) near Blackwater in central Queensland, all of which supply coal to a central coal preparation plant. South Blackwater Coal Ltd. recently developed a maintenance improvement programme, described in this article. The programme involved implementation systems of key performance indicators (KPIs), benchmaking, condition monitoring, work planning and control, failure analysis and maintenance audit. Some improvements became almost immediately apparent, others were quite gradual. Major results included: improved availability (and reliability) of all opencast fleets, improvements in rear dump availability; reduced maintenance man-hours for opencast fleets; and increased availability of the coal handling and preparation plant. The paper is an edited version of that presented at the `Maintenance in mining conference` 16-19 March 1998, held in Bali, Indonesia. 4 figs., 2 photos.

Hard coal; Steinkohle

Energy Technology Data Exchange (ETDEWEB)

Loo, Kai van de; Sitte, Andreas-Peter [Gesamtverband Steinkohle e.V., Herne (Germany)

2013-04-01

The year 2012 benefited from a growth of the consumption of hard coal at the national level as well as at the international level. Worldwide, the hard coal still is the number one energy source for power generation. This leads to an increasing demand for power plant coal. In this year, the conversion of hard coal into electricity also increases in this year. In contrast to this, the demand for coking coal as well as for coke of the steel industry is still declining depending on the market conditions. The enhanced utilization of coal for the domestic power generation is due to the reduction of the nuclear power from a relatively bad year for wind power as well as reduced import prices and low CO{sub 2} prices. Both justify a significant price advantage for coal in comparison to the utilisation of natural gas in power plants. This was mainly due to the price erosion of the inexpensive US coal which partly was replaced by the expansion of shale gas on the domestic market. As a result of this, the inexpensive US coal looked for an outlet for sales in Europe. The domestic hard coal has continued the process of adaptation and phase-out as scheduled. Two further hard coal mines were decommissioned in the year 2012. RAG Aktiengesellschaft (Herne, Federal Republic of Germany) running the hard coal mining in this country begins with the preparations for the activities after the time of mining.

Coal prices rise

International Nuclear Information System (INIS)

McLean, A.

2001-01-01

Coking and semi hard coking coal price agreements had been reached, but, strangely enough, the reaching of common ground on semi soft coking coal, ultra low volatile coal and thermal coal seemed some way off. More of this phenomenon later, but suffice to say that, traditionally, the semi soft and thermal coal prices have fallen into place as soon as the hard, or prime, coking coal prices have been determined. The rise and rise of the popularity of the ultra low volatile coals has seen demand for this type of coal grow almost exponentially. Perhaps one of the most interesting facets of the coking coal settlements announced to date is that the deals appear almost to have been preordained. The extraordinary thing is that the preordination has been at the prescience of the sellers. Traditionally, coking coal price fixing has been the prerogative of the Japanese Steel Mills (JSM) cartel (Nippon, NKK, Kawasaki, Kobe and Sumitomo) who presented a united front to a somewhat disorganised force of predominantly Australian and Canadian sellers. However, by the time JFY 2001 had come round, the rules of the game had changed

Health impacts of coal and coal use: Possible solutions

Science.gov (United States)

Finkelman, R.B.; Orem, W.; Castranova, V.; Tatu, C.A.; Belkin, H.E.; Zheng, B.; Lerch, H.E.; Maharaj, S.V.; Bates, A.L.

2002-01-01

Coal will be a dominant energy source in both developed and developing countries for at least the first half of the 21st century. Environmental problems associated with coal, before mining, during mining, in storage, during combustion, and postcombustion waste products are well known and are being addressed by ongoing research. The connection between potential environmental problems with human health is a fairly new field and requires the cooperation of both the geoscience and medical disciplines. Three research programs that illustrate this collaboration are described and used to present a range of human health problems that are potentially caused by coal. Domestic combustion of coal in China has, in some cases, severely affected human health. Both on a local and regional scale, human health has been adversely affected by coals containing arsenic, fluorine, selenium, and possibly, mercury. Balkan endemic nephropathy (BEN), an irreversible kidney disease of unknown origin, has been related to the proximity of Pliocene lignite deposits. The working hypothesis is that groundwater is leaching toxic organic compounds as it passes through the lignites and that these organics are then ingested by the local population contributing to this health problem. Human disease associated with coal mining mainly results from inhalation of particulate matter during the mining process. The disease is Coal Worker's Pneumoconiosis characterized by coal dust-induced lesions in the gas exchange regions of the lung; the coal worker's "black lung disease". ?? 2002 Elsevier Science B.V. All rights reserved.

Oxidation and carbonisation of coals: a case study of coal fire affected coals from the Wuda coalfield, Inner Mongolia, China

Science.gov (United States)

Kus, Jolanta; Meyer, Uwe; Ma, Jianwei; Chen-Brauchler, Dai

2010-05-01

At the coalfield of Wuda (Inner Mongolia, PR China) extensive underground coal fires cause widespread thermal and oxidative effects in coal seams. Within phase B of the Coal Fire Research Project of the Sino-German Initiative, methods for innovative fire-extinguishing technologies were investigated in multifaceted research approaches. Extensive investigations of oxidative and thermally affected coal seams in coal fire zone 18 were conducted in 2008 prior to application of new fire-extinguishing methods. We present results from the outcrop of coal seam No. 4 in the fire zone 18. The coal of seam No. 4 is of Early Permian age and belongs stratigraphically to the Shanxi Formation. The unaffected coal displays a high volatile bituminous A rank with a background value of random vitrinite reflectance ranging from 0.90 to 0.96 % Rr. Coal channel samples were coallected at actively extracted coal faces along multiple profiles with surface temperatures ranging from about 50° to 600°C. Microscopic examinations revealed a variety of products of coal exposure to the fire. Within coal samples, a marked rise in vitrinite reflectance from background values to 5.55% Rr (6.00 % Rmax) is encountered. In addition, a number of coal samples showed suppressed vitrinite reflectances ranging between 0.82 to 0.88% Rr. Further, seemingly heat unaffected coal samples display intensive development of oxidations rims at coal grain edges and cracks as well as shrinkage cracks and formation of iron oxides/hydroxides. Instead, thermally affected coal samples with higher coalification grade are further characterised by development of macropores (devolatilisation pores) in vitrinitic streaks, transformation of liptinite to meta-liptinite and micrinite as well as by natural coke particles of mostly porous nature and fine to coarse grained anisotropic mosaic. Coal petrographic investigations confirmed a hypothesis that both, oxidations as well as low temperature carbonisation govern the thermal

Proceedings of the sixth APEC Coal Flow Seminar. Coal in the new millennium

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

The 6th APEC Coal Flow Seminar titled on 'The coal in the new millennium' was held in Korea from March 14 to March 16, 2000, and the proceedings were summed up. In this seminar, as to economies of coal consumption countries and coal supply countries in the APEC region, discussions were made on coal supply/demand, coal price, environmental problems and others. The keynote address was 'Twenty first century coal in the APEC region and Republic of Korea' given by Mr. Gam Yeol Lee from Korea. The main theme of the seminar was 'The status quo for the coal market,' and lectures titled on the following were given from Japan: 'The status quo of coal purchase by the Japanese electric company and its outlook' and 'A perspective of coal fired IPP under environmental constraints and deregulation of electricity.' Lectures from Australia: 'Responding to coal market growth in APEC regions by the Australian coal industry' and 'The coal price impact on coal supply and demand.' Further discussions were made on 'The long-term outlook for coal supply/demand' and 'Economies report on the outlook for coal supply/demand.' (NEDO)

Coal -98

International Nuclear Information System (INIS)

Sparre, C.

1998-01-01

The following report deals with the use of coal and coke during 1997. Some information about technic, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from SCB have also been used. The use of steam coal for heating purposes during 1997 was 730 000 tons and about 500 000 tons lower than in 1996. The extremely high figures of 1996 were due to twice the production of electricity because of lack of hydro power. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generating plants. Some foreign analysts, however, estimate a doubled use of coal for energy use after 2020 because of the plans to phase out the nuclear power. During the top year 1987 coal was used in 18 hot water plants and 11 co-generation plants. 1997 these figures are 2 and 8. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1997 was 1.6 mill tons like the year before. 1.2 mill tons coke were produced. The coke consumption in the industry was 1.5 Mill tons. 0.3 mill tons of coke were imported. Several other plants have plans to replace the coal with forest fuels, waste fuels and NG. Even the biggest plant, Vaesteraas, has plans to build a block for bio fuels. Helsingborg has started to use wood pellets. The pellets replace most of the coal for the heat production in the co-generation plant. Norrkoeping Kraft AB has taken a fluid bed boiler for different fuels in operation, leading to more than half the coal consumption compared with previous years. They have also rebuilt one of their travelling grates for bio fuels. Stockholm

Coal marketing manual 1987

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

This manual provides information on the international coal market in tabulated format. Statistics are presented for the Australian coal industry, exports, currency movements, world coal production, coal and coke imports and exports. Detailed information is provided on the Australian coal industry including mine specific summaries. Pricing summaries for thermal and coking coal in 1987, coal quality standards and specifications, trends in coal prices and stocks. Imports and exports for World coal and coke, details of shipping, international ports and iron and steel production. An exporters index of Australian and overseas companies with industry and government contacts is included. 15 figs., 67 tabs.

Workability of coal seams in the Upper Silesian Coal Basin

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Fels, M; Soltysik, K

1978-04-01

This paper presents results of an investigation on workability of coal seams of stratigraphic groups from 100 to 700 in the: Upper Silesian Coal Basin. Analyzed are 2900 petrographic logs taken in the longwall workings and in narrow openings as well as about 9000 individual samples. Workability of coal seams, floors and partings is determined. Workability is described by the indicator f, (according to the Protodyakonov shatter method) and the indicator U, (compression strength of the unshaped test samples). The mean percentage content of indivi dual petrographic groups of coal as well as the mean workability indicator, f, of coals in the stratigraphic groups of coal seams in Upper Silesia are also determined.

Evaluation of Pakistani wheat germplasm for bread quality based on allelic variation in HMW glutenin subunits

Energy Technology Data Exchange (ETDEWEB)

Tabasum, A; Iqbal, N; Hameed, A; Arshad, R [Nuclear Institute for Agriculture and Biology, Faisalabad (Pakistan)

2011-06-15

Seventy six Pakistani wheat genotypes including land races were investigated for Bread quality (BQ) based on allelic variation in HMW glutenin subunits at the Glu-1 loci through SDS- polyacrylamide gel electropherosis. Twenty five different allelic combinations were detected with a total of 14 Glu-1 loci. Highest polymorphism was revealed by Glu-B locus and some single/ rare sub units were also screened out. The frequencies of dominant subunits were 50% for 2*, 42.11% for subunit pair 17+18 and 48.68% for 5+10 and 2+12 respectively. The quality scores displayed a range from 4 to 10, however generally good quality score of eight was more frequent (39. 47%). The highest quality scores of 10 and 9 were observed in 22.36% and 19.74% of genotypes respectively. The UPGMA analysis grouped genotypes into three major with two additional sub clusters for each. The cluster 'a' 'b' and 'C' were separated at 73% genetic distance which was further differentiated at a genetic distance of 50% into their sub clusters. Pakistani wheat varieties/land races exhibited large variation in term of HMW-GS. The generated information will lead to the pyrimiding of sub units for high BQ through mission oriented marker assisted breeding programmes for quality improvement of wheat. (author)

Evaluation of Pakistani wheat germplasm for bread quality based on allelic variation in HMW glutenin subunits

International Nuclear Information System (INIS)

Tabasum, A.; Iqbal, N.; Hameed, A.; Arshad, R.

2011-01-01

Seventy six Pakistani wheat genotypes including land races were investigated for Bread quality (BQ) based on allelic variation in HMW glutenin subunits at the Glu-1 loci through SDS- polyacrylamide gel electropherosis. Twenty five different allelic combinations were detected with a total of 14 Glu-1 loci. Highest polymorphism was revealed by Glu-B locus and some single/ rare sub units were also screened out. The frequencies of dominant subunits were 50% for 2*, 42.11% for subunit pair 17+18 and 48.68% for 5+10 and 2+12 respectively. The quality scores displayed a range from 4 to 10, however generally good quality score of eight was more frequent (39. 47%). The highest quality scores of 10 and 9 were observed in 22.36% and 19.74% of genotypes respectively. The UPGMA analysis grouped genotypes into three major with two additional sub clusters for each. The cluster 'a' 'b' and 'C' were separated at 73% genetic distance which was further differentiated at a genetic distance of 50% into their sub clusters. Pakistani wheat varieties/land races exhibited large variation in term of HMW-GS. The generated information will lead to the pyrimiding of sub units for high BQ through mission oriented marker assisted breeding programmes for quality improvement of wheat. (author)

Assessing coal burnout

Energy Technology Data Exchange (ETDEWEB)

Lowe, A. [Pacific Power, Sydney, NSW (Australia)

1999-11-01

Recent research has allowed a quantitative description of the basic process of burnout for pulverized coals to be made. The Cooperative Research Centre for Black Coal Utilization has built on this work to develop a coal combustion model which will allow plant engineers and coal company representatives to assess their coals for combustion performance. The paper describes the model and its validation and outlines how it is run. 2 figs.

Provision of Human Capital by Business Schools of Pakistan: A Need for the Sustainability of the Pakistani Banking Sector

Science.gov (United States)

Nauman, Sarwat; Hussain, Nasreen

2017-01-01

Economic growth of Pakistan through the banking sector relies heavily on the human capital dispensed to them by the Pakistani business schools. A conceptual model of the continuous improvement cycle for building human capital is developed through a literature review, with the aim of helping to generate human capital. Six semistructured interviews…

Ultravitrinite coals from Chukotka

Energy Technology Data Exchange (ETDEWEB)

Lapo, A.V.; Letushova, I.A.

1979-03-01

Chemical and petrographic analysis was conducted on coals from the Anadyrya and Bukhti Ugol'noi deposits. Characteristics of the most prevalent type of vitrinite coals in both regions are presented here. Anadyrya coals belong to a transitional phase between brown coal and long flame. Ultravitrinite coals predominate. Gas coals from Bukti Ugol'noi have a higher carbon content than Anadyrya coals. They also have a higher hydrogen content and yield of initial resin. In several cases there was also a higher yield of volatile substances. Chukotka coals are characterized by a 10 percent higher initial resin yield than equally coalified Donetsk coals, other indicators were equal to those of Donetsk coals. Because of this, Chukotka coals are suitable for fuel in power plants and as raw materials in the chemical industry. (15 refs.) (In Russian)

Coal surface control for advanced physical fine coal cleaning technologies

Energy Technology Data Exchange (ETDEWEB)

Morsi, B.I.; Chiang, S.H.; Sharkey, A.; Blachere, J.; Klinzing, G.; Araujo, G.; Cheng, Y.S.; Gray, R.; Streeter, R.; Bi, H.; Campbell, P.; Chiarlli, P.; Ciocco, M.; Hittle, L.; Kim, S.; Kim, Y.; Perez, L.; Venkatadri, R.

1992-01-01

This final report presents the research work carried out on the Coal Surface Control for Advanced Physical Fine Coal Cleaning Technologies project, sponsored by the US Department of Energy, Pittsburgh Energy Technology Center (DOE/PETC). The project was to support the engineering development of the selective agglomeration technology in order to reduce the sulfur content of US coals for controlling SO[sub 2] emissions (i.e., acid rain precursors). The overall effort was a part of the DOE/PETCs Acid Rain Control Initiative (ARCI). The overall objective of the project is to develop techniques for coal surface control prior to the advanced physical fine coal cleaning process of selective agglomeration in order to achieve 85% pyrite sulfur rejection at an energy recovery greater than 85% based on run-of-mine coal. The surface control is meant to encompass surface modification during grinding and laboratory beneficiation testing. The project includes the following tasks: Project planning; methods for analysis of samples; development of standard beneficiation test; grinding studies; modification of particle surface; and exploratory R D and support. The coal samples used in this project include three base coals, Upper Freeport - Indiana County, PA, Pittsburgh NO. 8 - Belmont County, OH, and Illinois No. 6 - Randolph County, IL, and three additional coals, Upper Freeport - Grant County- WV, Kentucky No. 9 Hopkins County, KY, and Wyodak - Campbell County, WY. A total of 149 drums of coal were received.

Computer-aided planning of brown coal seam mining in regard to coal quality

Energy Technology Data Exchange (ETDEWEB)

Ciesielski, R.; Lehmann, A.; Rabe, H.; Richter, S.

1988-09-01

Discusses features of the geologic SORVER software developed at the Freiberg Fuel Institute, GDR. The program processes geologic data from exploratory wells, petrographic characteristics of a coal seam model, technological mining parameters and coal quality requirements of consumers. Brown coal reserves of coking coal, gasification coal, briquetting coal and steam coal are calculated. Vertical seam profiles and maps of seam horizon isolines can be plotted using the program. Coal quality reserves along the surface of mine benches, mining block widths and lengths for excavators, maximum possible production of individual coal qualities by selective mining, and coal quality losses due to mining procedures are determined. The program is regarded as a means of utilizing deposit reserves more efficiently. 5 refs.

COAL Conference Poster

OpenAIRE

Brown, Taylor Alexander; McGibbney, Lewis John

2017-01-01

COAL Conference Poster This archive contains the COAL conference poster for the AGU Fall Meeting 2017 by Taylor Alexander Brown. The Inkscape SVG source is available at https://github.com/capstone-coal/coal-conference-poster/ under the Creative Commons Attribution-ShareAlike 4.0 International license.

Economic statistics for the mining and metallurgical industries: 1990. Statistique economique des industries extractives et metallurgiques annee 1990

Energy Technology Data Exchange (ETDEWEB)

Rzonzef, L.

1991-01-01

Provides economic statistics for the Belgian mining and metallurgical industries in 1990. The review is divided into 4 parts: the extractive industries (including an analysis of the coal market and mines, quarries and associated industries); coke and briquette making; metallurgy (i.e. blast furnaces, steel making, rolling mills and manpower and materials consumption in the steel industry); and the extraction of sand from the Belgian continental shelf. 17 tabs.

The association of glutathione S-transferase GSTT1 and GSTM1 gene polymorphism with pseudoexfoliative glaucoma in a Pakistani population.

NARCIS (Netherlands)

Khan, M.I.; Micheal, S.; Akhtar, F.; Ahmed, W.; Ijaz, B.; Ahmed, A.; Qamar, R.

2010-01-01

PURPOSE: The aim of the present study was to investigate the association of glutathione S-transferase GSTT1 and GSTM1 genotypes with pseudoexfoliative glaucoma (PEXG) in a group of Pakistani patients. METHODS: Multiplex polymerase chain reaction was used to study the GSTT1 and GSTM1 polymorphisms in

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

Economical and Energy Efficiency of Iron and Steel Industry Reindustrialisation in Russia Based on Implementation of Breakthrough Energy-Saving Technologies

Science.gov (United States)

Shevelev, L. N.

2017-12-01

Estimates were given of economical and energy efficiency of breakthrough energy-saving technologies, which increase competitive advantages and provide energy efficiency of production while reducing negative impact on the environment through reduction of emissions of harmful substances and greenhouse gases in the atmosphere. Among these technologies, preference is given to the following: pulverized coal fuel, blast-furnace gas recycling, gasification of non-coking coal in bubble-type gas-generators, iron-ore concentrate briquetting with steam coal with further use of ore-coal briquettes in electric furnace steel making. Implementation of these technologies at iron and steel works will significantly reduce the energy intensity of production through reduction of expensive coking coal consumption by means of their substitution by less expensive non-coking (steam) coal, and natural gas substitution by own secondary energy resource, which is the reducing gas. As the result, plants will get an opportunity to become self-sufficient in energy-resources and free themselves entirely from expensive purchased energy resources (natural gas, electric power, and partially coking coals), and cross over to low-carbon development.

Genetic characterization of different pakistani date palm varieties

International Nuclear Information System (INIS)

Akhtar, W.; Rashid, A.; Mahmood, T.

2014-01-01

Date palm (Phoenix dactylifera L.) is the oldest cultivated fruit tree and it has a great socioeconomic and nutritional value. Breeding programs and conservation rely on genetic characterization and diversity in gene pool. Its genetic diversity has not been focused more in Pakistan yet, therefore the present study aimed at the evaluation of genetic relationship based on chloroplast ribosomal protein gene (rps14). Rps14 gene was amplified and sequenced from selected varieties. Phylogram illustrated over all genetic distance of 0.001 representing close genetic relationship of selected P. dactylifera varieties. Pairwise distance was calculated for rps14 gene and very low genetic diversity values were observed ranging 0.003-0.017. Estimates of average evolutionary divergence of overall sequence pairs and nucleotide diversity were again found very low with 0.008 and 0.007 respectively. Sequences were analyzed by MEGA6, which revealed Pathri, Dhaddy, Makhi and Khudrawi as recent varieties. On the basis of rps14 genetic makeup, it can be suggested that Pakistani date palm varieties show very high degree of similarity. (author)

Height, weight and BMI percentiles and nutritional status relative to the international growth references among Pakistani school-aged children

Directory of Open Access Journals (Sweden)

Mushtaq Muhammad Umair

2012-03-01

Full Text Available Abstract Background Child growth is internationally recognized as an important indicator of nutritional status and health in populations. This study was aimed to compare age- and gender-specific height, weight and BMI percentiles and nutritional status relative to the international growth references among Pakistani school-aged children. Methods A population-based study was conducted with a multistage cluster sample of 1860 children aged five to twelve years in Lahore, Pakistan. Smoothed height, weight and BMI percentile curves were obtained and comparison was made with the World Health Organization 2007 (WHO and United States' Centers for Disease Control and Prevention 2000 (USCDC references. Over- and under-nutrition were defined according to the WHO and USCDC references, and the International Obesity Task Force (IOTF cut-offs. Simple descriptive statistics were used and statistical significance was considered at P Results Height, weight and BMI percentiles increased with age among both boys and girls, and both had approximately the same height and a lower weight and BMI as compared to the WHO and USCDC references. Mean differences from zero for height-, weight- and BMI-for-age z score values relative to the WHO and USCDC references were significant (P Conclusion Pakistani school-aged children significantly differed from the WHO and USCDC references. However, z score means relative to the WHO reference were closer to zero and the present study as compared to the USCDC reference. Overweight and obesity were significantly higher while underweight and thinness/wasting were significantly lower relative to the WHO reference as compared to the USCDC reference and the IOTF cut-offs. New growth charts for Pakistani children based on a nationally representative sample should be developed. Nevertheless, shifting to use of the 2007 WHO child growth reference might have important implications for child health programs and primary care pediatric clinics.

Coal at the crossroads

International Nuclear Information System (INIS)

Scaroni, A.W.; Davis, A.; Schobert, H.; Gordon, R.L.; Ramani, R.V.; Frantz, R.L.

1992-01-01

Worldwide coal reserves are very large but coal suffers from an image of being an environmentally unfriendly and inconvenient fuel. Aspects discussed in the article include: coal's poor image; techniques for coal analysis, in particular instrumented techniques; developments in clean coal technology e.g. coal liquefaction, fluidized bed combustion, co-generation and fuel slurries; the environmental impact of mining and land reclamation; and health aspects. It is considered that coal's future depends on overcoming its poor image. 6 photos

Promotive study on preparation of basis for foreign coal import. Study on coal renaissance

Energy Technology Data Exchange (ETDEWEB)

Muraoka, Yoji [Japan Economic Research Institute, Tokyo

1988-09-16

This is an interim report on the coal renaissance study carried out in 1987 as a part of the Promotive Study on Preparation of Basis for Foreign Coal Import. The background and ideology of coal renaissance, future aspect of demand for coal, problems pertaining to the expansion of application, and a proposal for the expansion of coal usage are described in order. The role of coal expected as an alternate fuel for petroleum, development of new application fields for coal, conversion to coal, contribution of Japan to the stablization of international coal supply are outlined. Coal renaissance aims, based on technology, at stimulation of coal demand, change in the image of coal, and the utilization of the accumulated abundant knowhow. The aspect of coal demand in 2000, solution and current status of various restricting factors relating to the use of coal in general industry, and the remaining problems are discussed. 6 figures, 10 tables.

Development of a method for determination of metallic iron content within hot briquette iron (HBI for steelmaking

Directory of Open Access Journals (Sweden)

Morcali M.H.

2016-01-01

Full Text Available The growing use of metallic iron in metallurgy and industrial chemical applications requires a fast, easy and cheap method for the determination of metallic iron, not merely in recyclable materials, such as iron pellets, reduced iron mill scale dust, electric arc furnace dust and pig iron, but from hot briquette iron (HBI as well. This study investigates a new method for determination of metallic iron within HBI used for steel-making materials. The effects of reaction time, temperature, and stirring rate were studied. The concentration of iron was determined via Atomic Absorption Spectroscopy (AAS. After the optimization study, high-purity metallic iron powder (Sigma-Aldrich, PubChem Substance ID 24855469 was used to compare efficiencies and identify the optimum conditions; The present study was matched with international standard methods (BS ISO 5416:2006, IS 15774:2007. Results were consistent with certified values and metallic iron content could be determined within the 95% confidence level. The purposed method is easy, straightforward, and cheap.

ACR coal 1992

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

This publication is a comprehensive reference document on production, exports, prices and demand of coal in world markets. A forecast of demand by coal type and country up to the year 2000 is provided. Statistics of the Australian export industry are complemented by those of South Africa, USA, Canada, Indonesia, China, C.I.S. and Colombia. A very comprehensive coal quality specification for nearly all the coal brands exported from Australia, as well as leading non-Australian coal brands, is included.

Statistical Analysis of Pakistani Currency Regime before and after Floatation

Directory of Open Access Journals (Sweden)

Shahid ALI

2011-05-01

Full Text Available In this paper the trends of exchange rates for the foreign currency are studied yearly for Pakistan rupee. In 2000 State bank of Pakistan officially floated the rupee. In this studies the trends of the exchange rate before floating and after floating and then checks its impact on the GDP per capita of the country. Here we consider the daily data of exchange rates of Pakistani currency from 1995 to 2009. Data was analyzed from 1995 to 2000 in the first step. In the second step data from 2001 to 2009 was analyzed. The result shows that if one wants to fl oat currency he must keep in mind that the political condition or stable and that the economy is also stable so that the system of fl oat can perform its functions completely.

Coal; Le charbon

Energy Technology Data Exchange (ETDEWEB)

Teissie, J.; Bourgogne, D. de; Bautin, F. [TotalFinaElf, La Defense, 92 - Courbevoie (France)

2001-12-15

Coal world production represents 3.5 billions of tons, plus 900 millions of tons of lignite. 50% of coal is used for power generation, 16% by steel making industry, 5% by cement plants, and 29% for space heating and by other industries like carbo-chemistry. Coal reserves are enormous, about 1000 billions of tons (i.e. 250 years of consumption with the present day rate) but their exploitation will be in competition with less costly and less polluting energy sources. This documents treats of all aspects of coal: origin, composition, calorific value, classification, resources, reserves, production, international trade, sectoral consumption, cost, retail price, safety aspects of coal mining, environmental impacts (solid and gaseous effluents), different technologies of coal-fired power plants and their relative efficiency, alternative solutions for the recovery of coal energy (fuel cells, liquefaction). (J.S.)

Coal Mines Security System

OpenAIRE

Ankita Guhe; Shruti Deshmukh; Bhagyashree Borekar; Apoorva Kailaswar; Milind E.Rane

2012-01-01

Geological circumstances of mine seem to be extremely complicated and there are many hidden troubles. Coal is wrongly lifted by the musclemen from coal stocks, coal washeries, coal transfer and loading points and also in the transport routes by malfunctioning the weighing of trucks. CIL —Coal India Ltd is under the control of mafia and a large number of irregularities can be contributed to coal mafia. An Intelligent Coal Mine Security System using data acquisition method utilizes sensor, auto...

Inorganic Constituents in Coal

Directory of Open Access Journals (Sweden)

Rađenović A.

2006-02-01

Full Text Available Coal contains not only organic matter but also small amounts of inorganic constituents. More thanone hundred different minerals and virtually every element in the periodic table have been foundin coal. Commonly found group minerals in coal are: major (quartz, pyrite, clays and carbonates,minor, and trace minerals. Coal includes a lot of elements of low mass fraction of the orderof w=0.01 or 0.001 %. They are trace elements connected with organic matter or minerals comprisedin coal. The fractions of trace elements usually decrease when the rank of coal increases.Fractions of the inorganic elements are different, depending on the coal bed and basin. A varietyof analytical methods and techniques can be used to determine the mass fractions, mode ofoccurrence, and distribution of organic constituents in coal. There are many different instrumentalmethods for analysis of coal and coal products but atomic absorption spectroscopy – AAS is theone most commonly used. Fraction and mode of occurrence are one of the main factors that haveinfluence on transformation and separation of inorganic constituents during coal conversion.Coal, as an important world energy source and component for non-fuels usage, will be continuouslyand widely used in the future due to its relatively abundant reserves. However, there is aconflict between the requirements for increased use of coal on the one hand and less pollution onthe other. It’s known that the environmental impacts, due to either coal mining or coal usage, canbe: air, water and land pollution. Although, minor components, inorganic constituents can exert asignificant influence on the economic value, utilization, and environmental impact of the coal.

Scholars' Satisfaction with Digital Library Collection and Gaps in the Provision of Effective Information Resources and Services: A Pakistani Perspective

Science.gov (United States)

Khan, Amjid; Ahmed, Shamshad; Masrek, Mohamad Noorman

2014-01-01

The study aims to explore the researchers' satisfaction with digital library resources and services and how they improved the research culture in Pakistani universities. A descriptive survey method was employed to achieve objectives of this study. Using stratified random sampling, for this survey we selected 14 public sector universities of Khyber…

Professorial Views of the Use of Diversity Experiences to Develop Students' Critical Thinking Skills in the Pakistani College Context

Science.gov (United States)

Tahir, Khazima

2017-01-01

This study explored the interplay of diversity experiences and critical thinking of Pakistani college students and determined how the classroom experience supported and exposed students to diversity and critical thinking. The researcher conducted teachers' interviews to gather data in a college in Pakistan. Teachers were asked to respond to a…

Coal-to-liquid

Energy Technology Data Exchange (ETDEWEB)

Cox, A.W.

2006-03-15

With crude oil prices rocketing, many of the oil poor, but coal rich countries are looking at coal-to-liquid as an alternative fuel stock. The article outlines the two main types of coal liquefaction technology: direct coal liquefaction and indirect coal liquefaction. The latter may form part of a co-production (or 'poly-generation') project, being developed in conjunction with IGCC generation projects, plus the production of other chemical feedstocks and hydrogen. The main part of the article, based on a 'survey by Energy Intelligence and Marketing Research' reviews coal-to-liquids projects in progress in the following countries: Australia, China, India, New Zealand, the Philippines, Qatar and the US. 2 photos.

Estimation of Moisture Content in Coal in Coal Mills

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, B.

the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...

Estimation of Moisture Content in Coal in Coal Mills

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2006-01-01

the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...

Material balance in coal. 2. Oxygen determination and stoichiometry of 33 coals

International Nuclear Information System (INIS)