Effect of heat treatment changes on swelling treatment of coal; Sekitan no bojun shori sayo ni oyobosu netsushori henka no eikyo

Energy Technology Data Exchange (ETDEWEB)

Satsuka, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

1996-10-28

Discussions were given on effects of heat treatment at relatively low temperatures as a pretreatment for coal liquefaction on coal swelling and hydrogenolysis reaction. Taiheiyo coal was heated to 200{degree}C for one hour as a pretreatment. The attempted heating methods consisted of four steps of rapid heating (6.7{degree}C/min)quenching (20{degree}C/min), rapid heating/natural cooling (0.7{degree}C/min), heating (1.0{degree}C/min)/quenching, and heating/natural cooling. The swelling treatment was composed of adding methanol benzene into heat treated coal, and leaving it at room temperature for 24 hours. The hydrogenolysis was carried out by using a tetralin solvent and at an initial hydrogen pressure of 20 kg/cm{sup 2} and a temperature of 350{degree}C and for a time of one hour. Hydrogenolysis conversion in the heat treated coal was found lower than that of the original coal because of generation of liquefaction inactive components due to thermal polymerization. When the heat treated coal is swollen by using the solvent, gas yield from the hydrogenolysis reaction decreased due to gas suppression effect, and the conversion was lower than that of the original coal. Heat treatment suggests densification of the coal structure. Swollen coal shows no conspicuous difference in the heat treatment methods against the hydrogenolysis due to the swelling effect. 3 refs., 5 figs., 1 tab.

Effects of gasoline properties on exhaust emission and photochemical reactivity; Gasoline seijo ga haiki gas sosei, kokagaku hannosei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kumagai, R; Usui, K; Moriya, A; Sato, M; Nomura, T; Sue, H [Petroleum Energy Center, Advanced Technology and Research Institute, Tokyo (Japan)

1997-10-01

In order to investigate the effects of fuel properties on emissions, four passenger cars were tested under Japanese 11 and 10-15 modes using two series gasoline fuels. The test results suggest that the distillation property (T90) affects A/F ratio which in turn influences exhaust emissions. The results of regression analysis show that both ozone forming potential and air toxics are highly corrected with the composition of aromatic hydrocarbons in gasoline. 3 refs., 10 figs., 6 tabs.

Effects of MTBE blended diesel fuel on diesel combustion and emissions; MTBE kongo keiyu ga diesel nensho haiki ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Shundo, S; Yokota, H; Kakegawa, T [Hino Motors, Ltd., Tokyo (Japan)

1997-10-01

The effects of MTBE (Methyl-t-butyl ether) blended diesel fuel on diesel combustion and emissions were studied. In conventional diesel combustion, the testing mode was carried out in conformity with the Japanese 13 mode. Furthermore, this fuel was applied to a new combustion system (Homogeneous Charge Intelligent Multiple Injection). MTBE blended diesel fuel is more effective in the case of new combustion system and very low NOx, PM capability is suggested. 6 refs., 6 figs., 2 tabs.

Effect of oxygenated fuel on premixed lean diesel combustion; Kihaku yokongo diesel nensho ni oyobosu gansanso nenryo kongo keiyu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

1998-05-01

Because injection timing in diesel engines is early in a premixed lean diesel combustion system using early fuel injection, ignition timing is determined by ignitability of the fuel used. The conventional diesel fuel, which has good ignitability, causes excessively early ignition, thus aggravating fuel consumption. In order to reduce cylinder temperature with an aim of delaying ignition timing to improve the fuel consumption, attempts are being made on using low cetane fuels to reduce CO2 gas supply or compression ratio, and to vary ignitability of the fuels. The present study investigated ignition timing control and properties of exhausts by mixing different types of oxygenated fuels into light oil. Mixing the oxygenated fuels into light oil proved that the ignition timing can be controlled, and mixing such low cetane fuels as ethanol and MTBE achieved improvement in fuel consumption. Trial use of the oxygenated fuels aggravated CO concentration, which is caused because the cylinder temperature was reduced. Numerical calculations suggest that use of fuels with faster evaporation speed and lower cetane number is effective in improving the fuel consumption and the exhausts. 12 refs., 9 figs., 2 tabs.

Effect of synthetic detergent and soap on the waste-water treatment. Gosei senzai oyobi sekken no haisui shori ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Inamori, Y. (national Institute for Environmental Studies, Tsukuba (Japan)); Takamatsu, Y. (University of Tsukuba, Tsukuba (Japan))

1993-05-01

This paper describes the effect of surfactants on purification capability and living life phases in the living life membrane method and the activated sludge method as biological waste water treatment methods. As a result of treating artificial waste water in an immersion hearth process of the living life membrane method, it was found that LAS added concentration at 50 mg/l or higher would not affect noticeably the quality of water treated under a steady-state operation, but that at 100 mg/l has aggravated the treated water quality by increasing COD. In the case of soaps, the COD in the treated water has aggravated when the added concentration is 70 mg/l or higher. The result of discussing the activated sludge process using urban sewage water indicated that COD in the treated water shows higher value for synthetic detergents than for soaps at the detergent added concentration of 140 mg/l or higher, having affected adversely the treated water quality. An activated sludge treatment process was operated to identify the effects of synthetic detergents and soaps on living life phases in the activated sludge and living life membranes. The result suggests that either the LAS added system or the soap added system presents no problems in a long-time aeration, while activated sludge aerated for the standard period of time has a possibility of abnormally proliferating filamentous microorganisms that can cause bulking in the soap system. 14 refs., 3 tabs.

Influence of smectites on resistivity of rocks and soils; Smectite nendo kobutsu ga ganseki dojo no hi teiko ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Takakura, S; Nishizawa, O; Aoki, M [Geological Survey of Japan, Tsukuba (Japan); Kozake, K [University of Tsukuba, Ibaraki (Japan)

1996-10-01

This paper illustrates the measurement results of resistivity for specimens including smectite clay minerals artificially synthesized, and also discusses the influence of smectites on resistivity. Three kinds of bentonites, i.e., KN-1, Kawasaki ore, and Kawasaki Sanhaku, were used for preparing smectites. The KN-1 is Na type smectite, the Kawasaki ore is Ca type smectite, and the Kawasaki Sanhaku is acid clay. It is well known that smectites lower the resistivity of rocks. However, the experimental results suggested that the degree of decreasing the resistivity depends on the kind of smectites. The effect of decreasing the resistivity by the KN-1 was much superior to the other smectites. For the KN-1, a thick electrical double layer was formed by Na ions in the interlayers, which resulted in the larger effect of decreasing the resistivity. Swelling capacity and cation exchange capacity (CEC) of the KN-1 were large, which agreed with the above mentioned consideration. Reversely, it was considered that smectites having larger effect of decreasing the resistivity exhibited larger swelling capacity and CEC. 4 refs., 3 figs.

Change in surface characteristics of coal in upgrading of low-rank coals; Teihin`itan kaishitsu process ni okeru sekitan hyomen seijo no henka

Energy Technology Data Exchange (ETDEWEB)

Oki, A.; Xie, X.; Nakajima, T.; Maeda, S. [Kagoshima University, Kagoshima (Japan). Faculty of Engineering

1996-10-28

With an objective to learn mechanisms in low-rank coal reformation processes, change of properties on coal surface was discussed. Difficulty in handling low-rank coal is attributed to large intrinsic water content. Since it contains highly volatile components, it has a danger of spontaneous ignition. The hot water drying (HWD) method was used for reformation. Coal which has been dry-pulverized to a grain size of 1 mm or smaller was mixed with water to make slurry, heated in an autoclave, cooled, filtered, and dried in vacuum. The HWD applied to Loy Yang and Yallourn coals resulted in rapid rise in pressure starting from about 250{degree}C. Water content (ANA value) absorbed into the coal has decreased largely, with the surface made hydrophobic effectively due to high temperature and pressure. Hydroxyl group and carbonyl group contents in the coal have decreased largely with rising reformation treatment temperature (according to FT-IR measurement). Specific surface area of the original coal of the Loy Yang coal was 138 m{sup 2}/g, while it has decreased largely to 73 m{sup 2}/g when the reformation temperature was raised to 350{degree}C. This is because of volatile components dissolving from the coal as tar and blocking the surface pores. 2 refs., 4 figs.

Characteristics of radiation temperature and radiosity coefficient by means of infrared radiometer. Sekigai hoshakei ni yoru zairyo hyomen no hosha tokusei ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Okamoto, Y; Kaminaga, F [Ibaraki University, Ibaraki (Japan). Faculty of Engineering; Ishii, T; Sato, K [Ibaraki University, Ibaraki (Japan); Kurokawa, T [NEC San-ei Instrumentsu Ltd., Tokyo (Japan)

1991-12-25

A radiation thermometer was applied to the measurement and analysis of radiation temperature of the material surface. In this paper, the characteristics of the radiation temperature and the radiosity coefficient of gray body materials are investigatied. An infrared radiometer was used, which detects radiation energy in the region between 8 and 13{mu}m of wavelength. This infared radiometer has a Hg-Cd-Te photon radiation sensor. The variation of emissivity was measured for the four kinds of non-metalic materials, i.e., graphite, carbon fiber composite, Si-SiC ceramic, and black paint spread on an aluminum plate. As a result, the relationship between material temperature and radiation energy was made clear. Furthermore, the space-dependent variation of the radiation temperature and the radiosity coefficient was derived from the two-dimensional CRT image of the infrared radiometer. Consequently, the emmisivity variation gave a maximum for the carbon fiber composite surface rich in irregularity, and decreased in the order of graphite, Si-SiC, and black paint. 7 refs., 15 figs.

Change of wettability of PTFE surface by sputter etching and excimer laser. Sputter etching oyobi excimer laser ni yoru PTFE hyomen no shinsuika

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, S. (Nitto Denko Corp., Osaka (Japan)); Kubo, U. (Kinki University, Osaka (Japan))

1994-06-20

The wettability of PTFE (polytetrafluoroethylene) surfaces was improved by sputter etching and excimer laser irradiation. In sputter etching, the PTFE surface was treated by reactive sputter etching with H2O gas to give active groups on the surface. In laser irradiation, the surface was irradiated in pure water by high-energy KrF excimer laser. As the surface wettability was evaluated with a contact angle to water, the contact angle decreased remarkably in both treatments resulting in a good improvement effect. In sputter etching, various new chemical bonds such as F-C=O, F2C-FC-O, F2C-C-O and C-O were observed because of a decrease in F and incorporation of oxygen. Such chemical bonds could be eliminated by ultraviolet ray irradiation, and the treated surface condition approached the initial condition after irradiation of 200 hours. In laser irradiation, it was suggested that C-F bonds were broken, and OH groups were added to the surface by dissociation of H2O to H and OH. 7 refs., 8 figs., 1 tab.

Influence of molybdenum on hardenability of destabilized high chromium cast irons. Ko kuromu chutetsu no netsushori tokusei ni oyobosu moribuden no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kuwano, M. (Ube, Collete of Technology, Yamaguchi (Japan)); Ogi, K. (Kyushu University, Fukuoka (Japan). Faculty of Engineering); Sawamoto, A. (Yamaguchi University, Yamaguchi (Japan))

1991-07-25

Alloy elements are added to compensate for reduction in hardenability of high chromium cast iron as a result of destabilization heat treatment. With the purpose of investigating the influence of the added elements, this paper describes investigations made on effects of Mo and destabilization heat treatment conditions on martensite transformation , eutectoid transformation and base hardness, using Fe-Cr-C-based alloy containing C at 1.6-3.6%, and Cr at 6.6-26%. The main results obtained are as follows: Mo and Cr had the distribution coefficient for initial crystal austenite is smaller than one and were microscopically segregated in the dendrite base; the solute element distribution in the base is homogenized as a result of the long-time destabilization heat treatment while the Cr and C concentrations reduce largely, and the Mo concentration increases slightly; Mo has little influence on the Ms point, and reduces with the smaller the Cr/C ratio and the higher the retention temperature; and the base hardness corresponds well to a CCT diagram. 14 refs., 11 figs., 1 tab.

Environmental assessment of surfactant using aquatic microcosm system; Konuma no suiken seitaikei ni oyobosu kaimen kasseizai no microcosm system wo mochiita hyoka

Energy Technology Data Exchange (ETDEWEB)

Takamatsu, Y.; Matsumura, M. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering

1995-10-10

Microcosm system was applied to assess effect of surfactants on aquatic ecosystem. Surfactants such as LAS and Soap were added to an aquatic flask-size microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer. In the system, NOEC (no observed effect concentration) of LAS was below 1.5mg{center_dot}l{sup -1}, whereas soap was below 30mg{center_dot}l{sup -1}. Microcosm test is a pertinent tool to assess the effect of surfactant on ecosystem because microcosm test makes it possible to evaluate the effect of surfactant from a viewpoint of the interaction of microorganisms, material cycle and energy flow. With these respects, microcosm test is useful environmental assessment method which can reflect aquatic ecosystem. 10 refs., 6 figs., 1 tab.

Effects of ferrous ions on the metabolism of sulfate-reducing bacteria; Ryusan`en kangenkin no taisha ni oyobosu tetsu ion no eikyo

Energy Technology Data Exchange (ETDEWEB)

Baba, F.; Suzuki, T. [Ajinomoto Co. Inc., Tokyo (Japan). Technology and Engineering Lab.]: Seo, M. [Hokkaido Univ., Sapporo (Japan). Graduate School

1995-11-15

The grave damages due to microorganisms occur occasionally to the ironic piping and the like when river water is used as industrial water. In the present researches, the effects of Fe{sup 2+} on the amount and activity of sulfate-reducing bacteria in the culture medium with the concentration of Fe{sup 2+} changed by stages from 3.6{times}10{sup -4} M to 0.7M are examined. Further, the relations between the activity of the bacteria and the amount of FeS generated in the medium are investigated as an in-site means to observe the activity of the bacteria in the medium wherein the produced S{sup 2-} is converted into FeS once it is generated. The following conclusions are drawn therefrom. In the initial medium with the Fe{sup 2+} concentration from 3.6{times}10{sup -4} M to 0.7M, the growth of the bacteria is maximum at the concentration of 1.0{times}10{sup -2}. Over this concentration the growth is weakened due to the osmotic pressure, lowering of nutriment and the deposit of waste, and the bacteria are extirpated due to the direct effect of osmotic press when the concentration is 0.7M. The total amount of FeS produced due to the bacteria is in conformity with the tendency of growth of bacteria till 30 hours of culture. 18 refs., 6 figs., 2 tabs.

Study of effects of engine oil additives on the properties of fluorelastomers; Fusso gomu ni oyobosu engine yu tenkazai no eikyo chosa

Energy Technology Data Exchange (ETDEWEB)

Kurono, K; Owaki, M; Suzuki, Y; Akiyama, K; Shionoya, M [Toyota Motor Corp., Aichi (Japan)

1997-10-01

Fluoroelastmers are well known for their resistance to heat and fluids and have become major material for crankcase oil sealers. On the other hand new additive formulations are developed for engine lubricants used for fuel economic gasoline engines. In this paper the effects of those additives on properties of fluoroelastmers are investigated. The results of the immersion tests of both test plaques and oil sealer products indicates that dithiocarbamates friction modifier have hardening effects on fluoroelastomers. The fluoroelastmer deterioration mechanism is presumed by analysis of elastmer samples after immersion in oil. 6 refs., 9 figs., 3 tabs.

Effect of ATF on frictional property of wet-type clutch; Shisshiki crutch (hasshin clutch) no masatsu tokusei ni oyobosu ATF no eikyosei

Energy Technology Data Exchange (ETDEWEB)

Yoshida, J; Nagashima, T; Yamane, T; Kawauchi, s; Hirao, Y [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

As a starting device for continuously variable transmission, wet-type multiple disc clutch installed to the driven side (Starting clutch system) is suitable system. Starting clutch system is feared to occur the judder phenomenon, because it is used at low slipping velocity like a lock up clutch. In this report, we studied to prevent the judder phenomenon about the effect of automatic transmission fluid on frictional property of the wet-type clutch. 6 refs., 7 figs., 2 tabs.

Surface modification method of rare earth-nickel hydrogen storage alloy for a battery; Denchiyo kidorui-nikkeru kei suiso kyuzo gokin no hyomen kaishitsu shoriho

Energy Technology Data Exchange (ETDEWEB)

Higashiyama, N.; Kimoto, M.; Matsuura, Y.; Kuroda, Y.; Nogami, M.; Nishio, K.; Saito, T.

1996-07-16

The characteristics of an alkaline battery with hydrogen storage alloy depend significantly on the activity of the used rare earth-nickel hydrogen storage alloy and require an activation process in its manufacturing. However, the previous manufacturing method was found to have a defect that surface modification cannot be uniformly conducted due to a rapid increase of pH of the processing solution during the processing. This invention aims to present a surface modification method to enable to produce uniform surface of the alloy particles with a high activity. In this invention, the rare earth-nickel hydrogen storage alloy is immersed in a buffer solution of pH 1 to 3.6 for a fixed period followed by washing with water or an alkaline solution. The rapid change of pH can be avoided by the use of the buffer solution and the surface of the alloy particles is modified uniformly. The use of the obtained alloy suppresses the increase of the internal pressure in the battery during charging and affords an alkaline battery with a long cycle life and a high performance. 1 fig., 3 tabs.

Effects of mechanical stimulating treatment on self-organization phenomena of materials; Kikaiteki reiki shori. Zairyo no jiko soshikia gensho ni oyobosu sono koka

Energy Technology Data Exchange (ETDEWEB)

Hida, M. [Okayama University, Okayama (Japan). Faculty of Mechanical Engineering

1999-03-31

The atoms and atom clusters around dislocation cores in crystals or surface layer deformed by mechanical energy are locally excited so as to give rise some chemical reactions and to self-organize their products into a kind of Spatial-Temporal Pattern Formation as a dissipative structure. A famous coupling phenomenon between mechanical and chemical process in solid materials must have been mechanical alloing. This report explains that various mechano-chemical treatments are powerfull method for entraining the solid system into non-equilibrium states and interesting phenomena stimulated by the mechanical self-catalysis reaction causing self-organization. (author)

Effect of oil around the pin boss bearing on bearing friction force; Piston pin jikuukebu kinbo no junkatsuyu ga masatsuryoku ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Takiguchi, M; Suhara, T; Ato, S; Someya, T [Musashi Institute of Technology, Tokyo (Japan)

1997-10-01

Piston pin bearings are engine parts placed under severe lubricating condition because of the high unit load and temperature and the low sliding speeds. Therefore, they are vulnerable to many lubrication problems such as abnormal wear, scuffs and seizures. In our recent study, the bearing friction were measured using a original measuring device and it was found out that the lubricating conditions of piston pin boss bearings are non-fluid lubrication due to the oil starvation. In this study, we have also measured the lubricating oil behavior around the pin boss bearing using a special cylinder with glass window, and analyzed the relationship between the friction force and the oil behavior at the pin boss bearings in a actual operating gasoline engine. 2 refs., 9 figs., 1 tab.

Effect of activated carbon on biodegradation of organic micropollutants in water; Suichu biryo yuki busshitsu no biseibutsu bunkai ni oyobosu kasseitan no koka

Energy Technology Data Exchange (ETDEWEB)

Fukuhara, T.; Nakano, S. [Osaka Municipal Technical Research Institute, Osaka (Japan)

1997-01-10

The effect of activated carbon (AC) on biodegradation of organic micropollutants in water was investigated, using fenitrothion, phenol and aniline as the model compounds, activated sludges cultured in a mixed solution of glucose, peptone and aniline, and Rhodotorula glutinis isolated as the phenol-degradation bacterium. The following conclusions are obtained by analyzing the corrected degradation curves derived from the adsorption equilibrium relationships, oxygen consumption characteristics and observed degradation curves. Biodegradation of each compound is accelerated in the presence of AC. Non-biological degradation of fenitrothion is also accelerated in the presence of AC, its effect being more noted in biodegradation and increasing as AC quantity increases. Phenol is biodegraded by different mechanisms, depending on its initial concentration. The maximum oxygen consumption rate during the biodegradation of phenol increases in the presence of AC, conceivably resulting from enhanced bacterial activities. 5 refs., 6 figs., 4 tabs.

Effect of Water Environment on Subcritical Crack Growth of Machinable Ceramics; Kaisakusei seramikkusu no kiretsu shinten tokusei ni oyobosu mizu kankyo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ikeda, K.; Kaizu, K.; Inotani, T. [Miyazaki Univ., Miyazaki (Japan); Yoshikawa, A.; Adachi, K.; Igaki, H. [Osaka Sangyo Univ., Osaka (Japan)

1997-06-15

The fatigue behavior of ceramics has been discussed on the basis of the relation between stress intensity facter (KI) and crack velocity (V). In this paper, the effect of environment on the relation between KI and V was studied on machinable ceramics (mica glass ceramics) and two kinds of glass ceramics with different grain sizes. The double torsion (DT) technique was used for the determination of the KI-V characteristics under different environments of air and ion-exchanged water. The characteristics of acoustic emission (AE) during stress corrosion cracking of mica glass ceramics was also examined. In water environment, the region II in the KI-V curve, in which crack velocity varies slowly with KI, disappeared. From this experimental fact, it was considered that at high KI, the crack velocity is encouraged by diffusion of the corrosive species to the crack and thus depended on the amount of water. SEM farc tography revealed that mica single crystals in the material caused crack arrest and deflection to occur. It is also found that AE event rate is quantitatively related to the crack velocity. AE measurement can be used in studying the crack propagation behavior of mica glass ceramics. 11 refs., 12 figs., 3 tabs.

Effects of electrical stimulation on fruit of lentinus edodes; Shiitake jinko kindoko ni taisuru denki shigeki ga kojittai hassei kosu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Mitobe, K.; Sato, T.; Yoshimura, N. [Akita Univ. (Japan)] Suzuki, T. [Tohoku Electric Power Co. Ltd., Sendai (Japan)

1997-11-30

So far, the cultivation of Lentinus edodes is cultivated from material wood mainly, however, recently, artificial bed-blocks method has been used widely. The advantage of bed-block cultivation is to a short growing period and be possible to cultivate by a large scale facilities. Hereafter, it is thought that this growing method is used mainly. Before now, based on the experimental fact that abnormal fruiting of Lentinus edodes occurs due to lightening, the study on the effects of electrical stimulation was reported, however, the investigation on the effects of electrical stimulation on the artificial bed-bocks which is thought to come into wide use in future does not carry out until now. The purpose of this study is to investigate an increased yield of the Lentinus fruit-bodies grown on artificial bed-blocks that electrical stimuli were applied. Nineteen artificial bed-blocks were provided for each applied voltage condition; Control, 200V, 400V, 600V, for the AC. As a result of experiment, in the 600V condition, the total number of fruiting of Lentinus edodes was significantly increased as compared with other conditions. Especially, in the artificial bed-blocks that peak current was over 300 mA, the total number of fruiting was increased. 6 refs., 6figs.

Effects of lithium iodide doping on devolatilization characteristics of brown coals; Yoka lithium no tenka ga kattan no kanetsu henka katei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Muraoka, J.; Kumagai, H.; Hayashi, J.; Chiba, T. [Hokkaido University, Sapporo (Japan)

1996-10-28

In order to discuss effects of lithium iodide (LiI) doping on condensation structure of brown coals during heating, spectral changes were measured by using an in-situ FT-IR. It was found that the LiI doping accelerates weight reduction due to heating, and the doping effect is affected by coal structure. Both of Loy Yang (LY) coal and its LiI doped coal (DLY) had absorption intensity of the FT-IR spectra decreased with rising temperature, and the absorption center belonging to an OH group shows different shifts between the LY and DLY coals. This indicates that the LiI doping has affected the change in hydrogen bonding patterns associated with heating. Both of South Banko (SB) and LY coals had the absorption spectral intensity in the OH group decreased as the weight reduction (conversion) rate increased. Reduction in the OH groups associated with heating is caused by volatilization and condensation reaction in light-gravity fraction. However, in the case of equal conversion rate, the LiI doped coal shows higher spectral intensity than the original coal, with the LiI doping suppressing reduction in the OH groups. It appears that the doping suppresses the condensation reaction between the OH groups. 2 refs., 6 figs., 1 tab.

Influence of frequency spectra to annoyance caused by road traffic noise; Doro kotsu soon no urusasa ni oyobosu shuhasu supekutoru no eikyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Ishiyama, T [Japan Automobile Research Institute Inc., Tsukuba (Japan); Hashimoto, T [Seikei University, Tokyo (Japan)

1997-10-01

This paper describes a study of annoyance to road traffic noise in laboratories. To measure the annoyance to road traffic noise, subjective evaluation test was carried out using 48 road traffic noise recorded at various points in the city. Among the frequency spectra of these noise, the differences on the SPL of high frequency component were significant. As a result, we found that: (1) annoyance was different while A-weighted SPLs were the same, (2) fluctuation strength had the highest correlation with annoyance, (3) besides A-weighted SPL, roughness and sharpness contributed to annoyance -simultaneously, (4) contribution of high frequency noise was significant to annoyance. 2 refs., 11 figs., 1 tab.

Effect of low oxygen partial pressure to the bumblebee respiration; Naruhanabachi ni okeru taikichu sanso bun'atsu henka no kokyu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Komai, Y. [Japan Science and Technology Corp., Tokyo (Japan)

1999-06-25

Insects augment oxygen supply using convective transport during flight in two ways: with deforming tracheae by surrounding muscles movement (muscle pumping) and with contracting air sacs by exoskeleton movement (abdominal or thoracic pumping). However, because induced flow inside tracheae is difficult to measure, it is not known how the convective transport actually contributes. By comparison between direct measurement of oxygen partial pressure in a flight muscle based on electrochemical method and flight/ventilation activities in a bumblebee, Bumbus hypocrita hypocruta, a method was developed for estimating gas transport efficiency. Oxygen partial pressure, P{sub 02}, in the bee periodically fluctuated with discontinuous abdominal movement in normal air. While the P{sub 02} strongly varied among individuals in normal air, the P{sub 02} took a unique value in oxygen poor air ({<=}8%). By enhancing ventilation, the bee could respire in an oxygen poor atmosphere up to 2%. Furthermore, the bee could fly in an atmosphere of 6%, in which the P{sub 02} decreased to 0.7%. Estimated efficiency of the gas transport increases with atmospheric oxygen concentration decreases. (author)

Improvement of In2O3-based CO sensor by using surface modifiers; Hyomen shushokuzai ni yoru sanka injiumukei soshi no CO kenchi tokusei no kaizen

Energy Technology Data Exchange (ETDEWEB)

Yamaura, H.; Miura, N.; Amaze, N. [Kyushu University, Fukuoka (Japan); Tamaki, J. [Ritsumeikan University, Kyoto (Japan); Moriya, K. [Osaka Gas Co. Ltd., Tokyo (Japan)

1998-02-01

Aiming at developing a semiconductor CO sensor applicable to the safety control of gas appliances, we carried out an extensive material search for promoters to In2O3-based elements. Among the elements added (0.5 wt%) with each of 12 transition metal oxides, the Co3O4-added one was outstanding in sensitivity and selectivity to CO at 200degC. Remarkably the sensing properties of this element could be improved further by the addition of Au (0.04 wt%). The doubly promoted element, Au(0.04 wt%)-Co(0.5 wt%)-In2O3, gave excellent characteristics in sensitivity to CO, selectivity to CO over H2 and other selected gases, and response rates at 250degC. The promoting effects of the additives were shown to originate from the proper enhancement of catalytic activity for CO oxidation. 11 refs., 9 figs.

Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, H; Sona, S; Koike, H; Hori, H; Negishi, N; Kohara, H; Ibusuki, A [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A; Borovkov, V [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

1997-02-01

Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

Effect of fuel composition on poly aromatic hydrocarbons in particulate matter from DI diesel engine; Particulate chu no PAH ni oyobosu nenryo sosei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Tanaka, S; Tatani, T; Yoshida, H; Takizawa, H; Miyoshi, K; Ikebe, H [COSMO Research Institute, Tokyo (Japan)

1997-10-01

The effect of fuel composition on poly aromatic hydrocarbons (PAH) in particulate matter from DI diesel engine was investigated by using deeply desulfurized fuel and model fuel which properties are not interrelated. It was found that the deeply desulfurized fuel have effect on reducing PAH emissions. Furthermore, it was suggested that poly aromatics in the fuel affect PAH emissions and the influence of tri-aromatics in the fuel was promoted by the coexistence of mono-aromatics or naphthene. PAH formation scheme from each fuel component was proposed by chemical thermodynamic data. 4 refs., 8 figs., 3 tabs.

Improvement in visual target detections and reaction time by auditory stimulation; Shikaku shigeki ga shikaku mokuhyo no kenshutsu to hanno jikan ni oyobosu kaizen koka

Energy Technology Data Exchange (ETDEWEB)

Mitobe, K.; Akiyama, T.; Yoshimura, N. [Akita University, Akita (Japan); Takahashi, M. [Hokkaido University, Sapporo (Japan)

1998-03-01

The purpose of this study was to investigate a traffic environment that can reduce traffic accidents of elder walker. We focused on the relationship between traffic accidents and elder person`s spatial attention. In this paper, an adolescent subject`s and an elder subject`s pointing movement to a visual target was measured in three conditions. Condition 1: Only target was presented. Condition 2: Auditory stimulation was added at a location the same distance from the center as that of the targets but in the opposite direction. Condition 3: Auditory stimulation was added at the same location as the target. The targets were placed in extra working space with the distance of 1.5 meter from a subject to the targets. In adolescent subjects, results showed that in Condition 3, latency was shorter and the error rate of pointing movements was lower than in the other conditions. In elder subjects, results showed that in all Conditions, ignore ratio to peripheral targets is higher than adolescent subjects. Nevertheless, in condition 3, ignore ratio was lower than in the other conditions. These results suggest that, it is possible to draw elder walker`s spatial attention and to control spatial attention by auditory stimulation. 13 refs., 6 figs., 1 tab.

Influence of hydrogen-ion concentration exponent on undrained shear behaviour of bentonites; Bentonaito no hihaisui sendan kyodo ni oyobosu suiso ion nodo shisu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kamei, T [Kiso Jiban Consultants Co. Ltd., Tokyo (Japan); Tokida, M [Nagano National College of Technology, Nagano (Japan)

1994-12-21

Because there is a report example that the yield stress of a landslide clay increases along with a decrease of a hydrogen-ion concentration exponent, it is thought that a shear strength of the landslide clay depends on the hydrogen-ion concentration exponent. Furthermore, when the soil stabilization method by lime is applied to the soft ground and high organic earth, it is pointed out that the hydrogen-ion concentration exponent will become one of the harmful factors. Accordingly, it is understood that revealing an influence of a hydrogen-ion concentration exponent affects on the characteristics of an earth is one of the important factors, to evaluate a strength, deformation and so forth of the viscous ground. In this study, in order to examine an influence of a hydrogen-ion concentration exponent affecting on an undrained shear behavior of the bentonites, for the artificially adjusted bentonite specimens with 5 kinds of different pH, the isotropic consolidated undrained triaxial compression tests were performed, and consequently an influence of pH affecting on the engineering characteristics of the bentonites was made clear quantitatively. 28 refs., 16 figs., 5 tabs.

Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

Energy Technology Data Exchange (ETDEWEB)

Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

1996-10-28

An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

Research and development of photovoltaic power system. Research on surface passivation for high-efficiency silicon solar cells; Taiyoko hatsuden system no kenkyu kaihatsu. Hyomen passivation no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Saito, T [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on surface passivation of high-efficiency silicon solar cells. In research on carrier recombination on SiO2/doped silicon interface, measurements were carried out on minority carrier life with respect to p-type silicon substrates with which phosphorus with high and low concentrations are diffused uniformly on the surface and non-uniformly on the back and then oxidized. The measurements were performed for the purpose of evaluating the carrier recombination at p-n junctions. Effective life time of oxidized test samples increased longer than that of prior to the oxidization as a result of effect of surface passivation contributing remarkably. In research on reduction in carrier recombination on SiO2/Si interface by using H radical annealing, experiments were conducted by using a method that uses more active H-atoms. As a result, it was revealed that the reduction effect is recognized at as low temperature as 200{degree}C, and photo-bias effect is also noticeable. Other research activities included analytic research on minority carrier recombination on micro crystalline silicon/crystalline silicon interface, and experimental research on evaluation of minority carrier life of poly-crystalline silicon wafers. 6 figs.

Engine performances and exhaust gas characteristics of methanol-fueled two-cycle engines. Kogata ni cycle ter dot methanol kikan no seino ni oyobosu shoinshi no eikyo

Energy Technology Data Exchange (ETDEWEB)

Sawa, N.; Kajitani, S. (Ibaraki Univ., Ibaraki (Japan). Faculty of Engineerineering); Hayashi, S.; Kubota, Y. (Muroran Inst. of Technology, Muroran (Japan))

1990-10-25

Regarding crank case compressed two cycle engine, feasibility of methanol-fueled engine was investigated by studying effective factors on properties of power, combustion, and exhaust gas. For the experiment, air-cooling single cylinder engine was used of which specification was shown by table. As for the experiment, quantities of in-taken air, fuel consumption, torque, and composition of exhaust gas were measured under various conditions. As the consideration of experimental results, those were obtained that less exhaust gas with high performance operation of tow-cycle engie was achieved, too, by using diluted mixture gas of methanol, and that problems were found to be studied for the realization of high compression ratio. 12 refs., 13 figs., 1 tab.

Ecological effects assessment of anionic surfactant on aquatic ecosystem using microcosm system; Microcosm wo mochiita in ion kaimen kasseizai no suiken seitaikei ni oyobosu eikyo hyoka

Energy Technology Data Exchange (ETDEWEB)

Takamatsu, Y. [University of Tsukuba, Tsukuba (Japan); Inamori, Y. [National Institute for Environmental Studies, Tsukuba (Japan); Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Kurihara, Y. [Ou Univ., Fukushima (Japan). Faculty of Engineering; Matsumura, M. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

1997-11-10

Microcosm system was applied to assess effect of anionic surfactant (LAS) on aquatic ecosystem. Anionic surfactant such as LAS was added to an flask microcosm consisting of four species of bacteria as decomposer, one species of ciliate protozoa (Cyclidium glaucoma), two rotifers (Philodina sp. and Lepadella sp.) and one aquatic oligochaete (Aeolosoma hemprichi) as predator, and a green alga (Chlorella sp.) and a filamentous blue-green alga (Tolypothrix sp.) as producer, comparing with that of an natural lake model ecosystem derived from natural lake water. In the flask microcosm system and the natural lake model ecosystem, biodegradation rates of LAS were almost same and NOECs (no observed effect concentration) of LAS were also below 1.5 mg{center_dot} l{sup -1}. It was found that flask microcosm test could provide precise ecological effect assessment of LAS on number of microorganisms because the system showed higher reproducibility and stability than natural take model ecosystem. It was suggested that flask microcosm test was useful ecological effect assessment method which can reflect natural aquatic ecosystem. 10 refs., 4 figs., 2 tabs.

Influence of strain hardening and thickness changes occurring in press forming process; Seikeiji no kako koka/itaatsu henka no buzai akkai tokusei ni oyobosu eikyo bunseki

Energy Technology Data Exchange (ETDEWEB)

Ueno, M; Hirota, K [Mazda Motor Corp., Hiroshima (Japan); Nakazawa, Y [Sumitomo Metal Industries Ltd., Osaka (Japan)

1997-10-01

Most components of the body structure are produced by press forming. This process make a uniform metal sheet into a component that have various material characteristics and thickness. This paper describes the estimation method of material characteristics and thickness changes based on the measured Vickers hardness, and the influence of these changes on the crush performance by using FE analysis. 4 refs., 12 figs., 2 tabs.

Effect of laser heat treatment on intergranular corrosion of austenitic stainless steel; Austenite kei stainless ko no ryukai fushoku kanjusei ni oyobosu laser netsushori no eikyo

Energy Technology Data Exchange (ETDEWEB)

Osawa, M.; Yoneyama, T. [Tokyo Denki University, Tokyo (Japan). Faculty of Engineering; Isshiki, Y. [Tokyo Metropolitan Industrial Technology Center, Tokyo (Japan)

1995-03-15

The laser heat treatment of SUS304 steel was studied to lower the intergranular corrosion sensitivity of austenitic stainless steel. By the short-time heating around 923K, the SUS304 steel is sensitized to the intergranular corrosion with the deposition of Cr carbide into the granular field of crystals. To recover it, it is necessary to solidly dissolve, and simultaneously, quickly cool the Cr carbide above 1273K. For such solution heat treatment, CO2 laser beams were used with the treatment condition that the power and beam diameter were 800 to 1200W and 0.3 to 0.64cm, respectively. Regardless of both power density and beam diameter, the desensitization was observed at heating temperatures above 1323K. As a result of calculation by simulation, the solid dissolution of Cr carbide and recovery of Cr`s depletion zone in the granular field of crystals took place in a very short time at heating temperatures above 1323K. It agreed well with the experimental result. The laser beams are effective in the solution heat treatment of stainless steel. 14 refs., 15 figs., 1 tab.

Effect of fish on water quality and nutrients cycle from an outdoor pond experiment; Sakana no suishitsu, busshitsu junkan ni oyobosu eikyo ni kansuru jikkenteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Fukushima, T.; Matsushige, K.; Aizaki, M. [National Inst. for Environmental Studies, Tsukuba (Japan); Park, J.; Goma, R. [Tokyo University of Fisheries, Tokyo (Japan); Kong, D. [Korea National Institute of Environmental Research, Seoul (Korea, Republic of)

1995-11-10

The influences of fish (goldfish) on water quality and nutrients cycle (carbon, nitrogen, phosphorus) were investigated during 39 days in the summer of 1993, using six outdoor experimental ponds (36 m{sup 3}) with the same water residence times and nutrient inputs. Blue-been algae dominated the ponds with fish. Compared with ponds without fish, the ponds with high densities of fish had standing stocks of zooplankton and macrozoobenthos nearly one order of magnitude lower, about twice the concentrations of chlorophyll a and twice the rate of primary production. Settling rates of particulate substances in the high density ponds were nearly half those observed in ponds with no fish. The processes of sedimentation and exchange with air played important roles in the nutrient budgets as well as the in- and outflows and the changes in nutrient standing stocks. The high concentrations of chlorophyll a in the fish ponds were attributed in part to the lower zooplankton grazing pressure and in part to the higher nutrient concentrations due to lower settling rates and rapid nutrient recycling between biomass and dissolved components. 28 refs., 8 figs., 6 tabs.

Effect of grain size on amplitude-dependent internal friction in polycrystalline copper. Do takessho no naibu masatsu no shinpuku izon sei ni oyobosu kessho ryukei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Goto, H.; Nishino, Y.; Asano, S. (Nagoya Inst. of Technology, Nagoya (Japan))

1991-08-20

In this research, amplitude-dependency of internal friction was measured on various polycrystalline copper of varying grain size. Furthermore, the measurement data of amplitude-dependency of internal friction were analyzed from the phenomenological standpoint and microplastic strain was calculated as a function of stress. The obtained correlation between microplastic strain and stress corresponded to the stress-strain curve obtainable from normal tensile tests. Hence, comparing with the Hall-Petch relation, the relationship between flow stress and grain size in the microplastiic zone was discussed. The obtained results are summarized as follows: When grains were refined, amplitude dependency of internal friction was inhibited. As a result of the analysis of the data obtained, it was found that the flow stress in the microplastic zone increased following refining of grains. This agreed qualitatively with the macro deformation obtained from normal tensile tests. The grain size dependency of flow stress in the microplastic zone did not follow the normal Hall-Pitch relation, but the plastic strain increased, the dependency moved towards it. 16 refs., 4 figs.

Effect of separation and drainage of condensate on dehumidification in a refrigerated dryer; Reito joshitsuki ni okeru gyoshukusui bunri/haishutsu noryoku no joshitsu seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Goto, H.; Ichinose, T. [SMC Corp., Tokyo (Japan); Tanzawa, Y.; Hashizume, T. [Waseda Univ., Tokyo (Japan). Science and Engineering Research Lab.

1995-11-15

The representative refrigerated dryer as the compressed air dryers is one in which air was cooled at rather low temperature by working medium of refrigerators, and the dew point was decreased with increase of pressure, and air with low relative humility called as the dried air was obtained again by heating. In this paper, for clarifying effect of separation and drainage of condensate on dehumidification in a refrigerated dryer in relation to shape of a main cooler and a precool-reheater and air temperature of each part, calculation and experimental investigation were conducted. In a refrigerated dryer, condensate happened in the precool part of a precool-reheater and a main cooler, and this would give rise to reduce of separation and drainage of condensate and increase of thermal loads of each heat exchange, and would made dehumidification low. For a fact that decrease of separation and drainage of condensate in a main cooler would bring out heat conduction with phase change in the reheating part of a precool-reheater, it has a profitable side, but it is not desirable for ability of dryers. 6 refs., 9 figs., 1 tab.

1998 Annual Study Report. Standardization of corrosion resistance testing/evaluation methods for coated steel sheets; 1998 nendo seika hokokusho. Hyomen shori koban no taishokusei shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to develop the evaluation methods for reappearing corrosion characteristics of coated steel sheets in a short time, acid rain composition and artificial acid rain composition for the accelerated test were studied, and the cyclic corrosion tests were conducted. The literature survey shows that the main ionic species present in acid rain are Ca{sup 2+}, Mg{sup 2+}, Na{sup +}, K{sup +}, NH{sub 4}{sup +}, SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, and Cl{sup -}, of which the acid rain components are SO{sub 4}{sup 2-} and NO{sub 3}{sup -}, their equivalent ratio (NO{sub 3}{sup -}/ SO{sub 4}{sup 2-}) in the Far Eastern area being 0.2 to 0.3. Therefore, the solution specified by ASTM 1141 is diluted 30 times with water to prepare the base solution for the accelerated tests, where its acidity is adjusted with a mixed acid of NO{sub 3}{sup -}/ SO{sub 4}{sup 2-} = 0.2 to 0.3 (pH: 3.0 to 4.0). Two sets of preliminary cyclic corrosion tests were conducted, one involving acid rain spraying, drying and humidification in this order, and the other acid rain spraying, humidification and drying. Analysis of the test data indicates that difference between these test cycles in corrosion rate is within a deviation range caused by different testing tools. Therefore, the former condition is adopted as the basis for the accelerated tests, because of its smaller deviation caused by different testing tools. (NEDO)

Relationship between surface structure of silicon containing steel and adhesion of hot dip galvanized coating; Si gan'yu koban no hyomen kozo to yoyu aen mekki micchakuseino kankei

Energy Technology Data Exchange (ETDEWEB)

Tsuchiya, Y.; Hashimoto, S.; Ishibashi, Y. [Kokan Keisoku K.K., Kawasaki (Japan); Inagaki, J. [NKK Corp., Tokyo (Japan); Fukuda, Y. [Shuibuoka University, Shizuoka (Japan)

2000-06-01

The surface of the annealed steel and the exfoliated interface of the coating for the hot dip galvanized Si containing steel sheets was characterized by using SEM (Scanning Electron Microscope), AES (Auger Electron Spectroscopy) and TEM (Transmission Electron Microscopy). The adhesion of the coatings have depended on the Si content of the steel. It have been found that MnSiO{sub 3} particles are formed at the surface of the annealed steels having high Si content and that two types of grain having different distribution of the oxide exist in the steels. Large oxide particles have been formed in one type of grain and small particles are formed in the other type of grain. The different type of Fe-Zn alloy are formed on two types of grains. It have been observed that the oxide particles exist at the interface of exfoliated coatings after the adhesion test for the steels with high Si content. The distribution of the oxide particles observed at the bottom of the exfoliated coating is quite similar to that of the surface oxide of the annealed steel. From these results, the exfoliation of the coating has initiated at the oxide particles of the steel surface that has been not reduced during the hot dip galvanizing. (author)

Improvement of sensitizatiuon in weld metals of austenitic stainless steels by laser surface melting treatment. Report 3. Study on low temperature sensitization in weldments of austenitic stainless steels ans its improvement by laser surface melting treatment; Reza hyomen yoyu shori ni yoru sutenresu ko yosetsu kinzoku no enbinka kaizen. 3. Osutenaito kei sutenresu ko yosetsubu no teion enbinka to reza hyomen yoyu shori ni yoru sono kaizen

Energy Technology Data Exchange (ETDEWEB)

Nishimoto, K. [Osaka Univ., Osaka (Japan). Faculty of Engineering; Mori, H. [Osaka Univ., Osaka (Japan). Graduate School; Yamamura, T. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

1997-05-05

Laser surface melting treatment used for the improvement of intergranular corrosion resistance of sensitized austenitic stainless steel weld metal was studied. As a result, it was revealed that as compared to untreated material, sensitization was improved widely and intergranular corrosion resistance was improved to a level of base metal when laser surface melting treatment of sensitized weld metal was carried out. Further, sensitization effect at a condition of laser traveling velocity of 0.00167m/s was slightly insufficient compared to that of laser traveling velocity above 0.00833m/s. This phenomena was caused due to the existence of {delta} ferrite that accelerates the precipitation of Cr carbides inside the laser treatment portion and together with this, the Cr carbides are precipitated in {delta}/{gamma} grain boundary due to the effect of laser heat cycle with insufficient cooling velocity and this has caused desensitization. 16 refs., 13 figs., 3 tabs.

Assessment of a Mega-Float on water quality and ecosystem in Tokyo bay; Choogata futaishiki kaiyo kozobutsu ga Tokyowan no suishitsu to seitaikei ni oyobosu eikyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kyozuka, Y.; Hu, C.; Hasemi, H. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hikai, A.

1997-08-01

The effect on the marine environment in the bay when a Mega-Float is installed in a bay was investigated. The physical process such as a residual flow (including tidal currents, water temperature, salt, density, and density currents), and the ecosystem model for which floating organic matter and plankton are handled were incorporated to develop a program for water quality calculation in a bay. The program was used for Tokyo Bay and compared with the conventional calculation result and the oceanograhpic observation result. Simultaneously, the effect on the Mega-Float was considered. On the flow in Tokyo Bay in summer, the calculation result that comparatively coincided with the observation value in a residual flow level was obtained. The horizontal distribution of COD comparatively coincides with the existing observation result. The influence that the Mega-Float exerts on the flow, water temperature, water quality, and ecosystem in the ambient sea area was little and local in the calculation scale (L {times} B {times} d = 6 km {times} 3 km {times} 2 m) of this time. However, the difference occurring due to the design position must also be investigated in future. 12 refs., 8 figs., 5 tabs.

FY1995 studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; 1995 nendo handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Development of the semiconductor photocatalyst such as titanium dioxide is important for photo-energy conversion and purification of the environment. We make clear that the mechanism of the photocatalysis using a spectroscopic or physico-chemical methods, and we developed the new photocatalyst with the control of the surface area, porosity, infinitesimal content, and surface modification of the catalyst surface. Titanium dioxide thin film photocatalysts were prepared by the dip coating method. Surface structure of the thin film was formed by the aggregated TiO{sub 2} anatase particle, its size was around 5 nm. This thin films effectively oxidazed NO, its photocatalytic activity is higher than that of commercial photocatalyst. Metal oxide anchored TiO{sub 2} photocatalysts (RuO{sub 2}/TiO{sub 2}) were prepared by the co-precipitation method. Effective charge separation of the RuO{sub 2}/TiO{sub 2} were confirmed by the measurement of ESR. The RuO{sub 2}/TiO{sub 2} photocatalyst successfully reduced CO{sub 2} and preserved its activity for much longer period than metal loaded catalyst. Hybrid photofunctionalized material was prepared by anchoring porphyrin moieties on the titanium dioxide surface. The relative quantum yield of electron transfer from porphyrin to the titanium dioxide conduction band has been markedly increased by water treatment of quanternized porphyrin-titanium dioxide covalently linked systems owing to removal of adsorbed porphyrin domains. (NEDO)

Influence of fragmentation of substrate on synergistic effect in hydrolysis of crystalline cellulose with cellulases; Seruraze niyoru kessho serurosu bunkaikatei deno sojokoka ni oyobosu kishitsu no danpenka no eikyo

Energy Technology Data Exchange (ETDEWEB)

Tanaka, M.; Morita, M.; Mitsui, R. [Okayama University of Science, Okayama (Japan). Dept. of Biochemistry

2000-05-10

The expression mechanism of synergistic effect is investigated by using two cellulase components obtained from Meicelase CEP-6000 by purification. Purified cellulose components are classified into two types. One, tentatively named CMCase-type (FIE and FIIIE), has relatively low values of the ratio of MCC hydrolysis to CMC hydrolysis, and considerably high values of the ratio of K{sub m} for MCC and CMC. The other, tentatively named MCCase-type (FIIE and FIVE), has largely different values about those properties. In the case of MCC hydrolysis with FIVE alone, the particle diameter of MCC decreases (fragmentation) and the particle number of MCC increased rapidly in the early stage of reaction, and both decrease gradually in the late stage of reaction. In the case of a mixture of the above two components is for an increase in amounts of reaction site in the substrate for FIIIE, dependent on fragmentation of MCC by FIVE, and the activity of FIVE is stimulated by FIIIE. In the case of the mixture of FIE and FIIIE, the synergistic effect is not expressed. This finding suggests that these two components do not have the activity of fragmentation of MCC. (author)

Effect of heat transfer in cylinder on air quantity of 4-stroke cycle gasoline engine; 4 Stroke gasoline engine no kyunyu shinkiryo ni oyobosu cylinder nai dennetsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yoshida, M.; Oguri, Y.; Suzuki, T. [Sophia University, Tokyo (Japan). Faculty of Science and Technology

2000-01-25

Many papers concerning air quantity of 4-stroke cycle gasoline engine have been published. It has been reported in these papers that heat transfer in surface of cylinder and inlet port gives big influence to the air quantity. But it has not been clear which influence of heat transfer in cylinder and inlet port is strong. So the authors derived a function of the air quantity thermodynamically considering heat transfer, and examined which of influence of heat transfer was strong. The results show ; (1) The influence of heat transfer in cylinder is small (about 1%) at full load, and is also small (about 5%) at light load. (2) Heat transfer in cylinder almost increases the air quantity. (3) The influence of heat transfer in inlet port decreases the air quantity with around 30% greatly. (author)

Effects of short fiber reinforcement and mean stress on tensile fatigue strength characteristics of polyethersulfone; Tansen`i kyoka porieterusaruhon no hippari hiro tokusei ni oyobosu heikin oryoku no eikyo

Energy Technology Data Exchange (ETDEWEB)

Furue, H.; Nonaka, K. [Mechanical Engineering Lab., Tsukuba, Ibaraki (Japan)

1996-01-15

Thermoplastics are often reinforced with short fibers with aims of improvement of their strengths, rigidities and hardness or maintenance of their dimensional stabilities. Such short fiber reinforced plastic materials have more expectation for high performance plastics. Authors already examined of some effects of reinforced fiber and of orientation in injection molding on flexural fatigue characteristics of the injection-molded high performance thermoplastic materials. However, the examination of short fiber reinforced effects on fatigue strength characteristics was not always sufficient. In this study, in order to obtain a guiding principle for fatigue resistant design of the short fiber reinforced injection molding materials, polyethersulfones (PES) was examined on its tensile fatigue strength and an effect of short fiber reinforcement for improvement of its fundamental dynamic properties on its fatigue characteristics. Especially, its fatigue life characteristics was elucidated mainly on relationship of mean stress, stress amplitude and number of repeating fracture in tensile fatigue behavior. 10 refs., 15 figs., 2 tabs.

Effect of metal ion species on mechanical relaxation of ethylene-co-methacrylic acid based ionomers; Ethylene-metakuriru san ionomer no rikigaku kanwa ni oyobosu kinzoku ion shu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Zeng, X; Araki, O; Takigawa, T; Masuda, T [Kyoto University, Kyoto (Japan); Takahashi, M [Kyoto Institute of Technology, Kyoto (Japan)

1996-12-15

Dynamic viscoelasticity of ethylene-co-methacrylic acid (EMAA) based ionomers containing Zn or Na as well as EMAA was investigated. The film samples used for viscoelasticity measurements were molded at 195{degree}C. Two kinds of specimens, quenched and slowly cooled samples after molding, were prepared for each polymer specimen. For the quenched samples, the effect of aging on dynamic viscoelasticity was also examined. The temperature dispersion curves of dynamic storage modulus (E{prime}) of the ionomers obtained by quenching showed a large decrease around 35{degree}C due to the glass transition of EMAA ionomers. The ionomers prepared by slow cooling showed a high value of E{prime} in the high temperature region, compared with the quenched samples. This may be due to the difference in the degree of ionic cluster formation in the ionomers. The values of E{prime} at low temperatures increased with aging time for the quenched samples, which originates from the equilibration of the glassy state by aging. 14 refs., 7 figs., 1 tab.

Fiscal 1998 development report on the high-accuracy quantitative analysis technique of catalyst surfaces by electron spectroscopy; 1998 nendo denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This project aims at development of the high-accuracy quantitative analysis technique by electron spectroscopy for surface analysis of catalysts and semiconductors. Since conventional analysis technique using an energy-fixed X-ray excitation source is inadequate to obtain satisfactory surface sensitivity and quantitative accuracy for catalysts, for development of the titled technique, this project makes experiment using energy-variable synchrotron radiation to modify the parameter on motion of low-speed electrons in solids which is obtained by Monte Carlo calculation. For establishment of the high-accuracy quantitative analysis technique of surface compositions of materials such as catalyst of which performance is dominated by utmost surface, the project studies the attenuation length of electrons in solids by electron spectroscopy using soft X-rays from synchrotron radiation. In this fiscal year, the project established the equipment and technique for high-accuracy quantitative analysis of the thickness and electron attenuation length of silicon oxide films on silicon wafers by electron spectroscopy. (NEDO)

Effect of insolation forecasting error on reduction of electricity charges for solar hot water system; Taiyonetsu kyuto system no denki ryokin sakugen koka ni oyobosu nissharyo yosoku gosa no eikyo

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan)

1996-10-27

A solar hot water system can be economically operated if inexpensive midnight power is purchased to cover the shortage of solar energy predicted for the following day. Investigations were conducted because error in insolation prediction affects the system operation and electric charge reduction effect. The target temperature of the heat accumulation tank at every predetermined time point is calculated on the previous evening in consideration of predicted insolation so that the water will be as hot as prescribed at the feeding time on the following day. Midnight power is used for uniform heating to attain the target temperature for 7 o`clock on the following morning. The uniform heating continues from 8 o`clock to the feeding time, this time using solar energy and daytime power to attain the target temperature. Accordingly, the division between the midnight power and daytime power is determined in view of the target temperature for 7 o`clock on the following morning, which target temperature is so set that the charge will be the minimum by optimizing the allocation of the above-said two. When the insolation prediction error rate is beyond 30%, the electric charge grows higher as the rate rises. But, when the rate is not higher than 30%, the charge is little affected by a rise in the rate. 5 refs., 10 figs., 1 tab.

Surface treatment method for hydrogen adsorbing alloy powder and alkali secondary battery fabricated by applying the method; Suiso kyuzo gokin funmatsu no hyomen shori hoho to sorewo tekiyoshite eraeta arukari niji denchi

Energy Technology Data Exchange (ETDEWEB)

Nishimura, K. [Furukawa Electric Co. Ltd., Tokyo (Japan); Sawa, H. [The Furukawa Battery Co. Ltd., Yokohama (Japan)

1997-03-07

Corrosion of alloy proceeds in the conventional hydrogen absorbing alloy because the composing hydrogen absorbing alloy powder contacts with high concentration alkali electrolyte in the battery. Immersion into alkali aqueous solution and pulverization by metal fluoride compound of the electrode have been practiced to solve the problem, but internal resistance of the battery increases and the charge and discharge properties of the battery are deteriorated. This invention relates to a method in which hydrogen absorbing alloy electrode powder or the hydrogen alloy electrode whose main content is the said powder is contacted with alkali aqueous solution to increase the specific surface area of the hydrogen absorbing alloy powder, followed by its contact with pH3-6 acidic aqueous solution containing fluorine ions. As a result, corrosion resistance of the surface of hydrogen absorbing alloy powder after the treatment against high concentration alkali electrolyte is improved to elongate the cycle life. Salts of LiF, NaF, KF, RbF, and CsF or their hydrogen salts can be used as the supply source of fluorine ions. 3 tabs.

Effect of heat generation from bone cement on bone tissue in total knee arthroplasty; Jinko kansetsu okikaeji no one cement no hatsunetsu ga seitai soshiki ni oyobosu eikyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Matsuda, M.; Uchida, T. [Kobe University, Kobe (Japan); Iwatsubo, T. [Kobe University, Kobe (Japan). Faculty of Engineering; Kurosawa, M.; Hashimoto, Y. [Kobe University, Kobe (Japan). Faculty of Medicine; Fukushima, H.

1998-01-25

Bone cement is often applied to fix the components in a surgical operation, such as TKA (total knee arthroplasty). In this paper, we consider the effect of heat generation from bone cement on bone tissue in TKA by using numerical simulation. First, we applied an axisymmetric model of tibia to finite element method and analyzed heat generation of bone cement. To confirm the results of analysis by experiment, we measured the temperature determined by 6 points i.e., 2 points each in component-cement interface, cement and bone-cement interface. As a result, the temperature determined by analysis agrees with that determined by experiment. Next, we proposed the evaluation formula of the bone necrosis. We constructed a bone necrosis map from the simulation. From the map, we found that the bone necrosis region was about 2 mm from the bone-cement interface. In addition, the bone necrosis is severe at the base of the tibial component. 7 refs., 15 figs., 3 tabs.

Estimation of real ship propelling performance by the surface velocity lattice method using model ship flow field data; Mokeisen ryujo data wo mochiita hyomen uzu koshiho ni yoru jissen suishin seino no suitei

Energy Technology Data Exchange (ETDEWEB)

Kai, H; Ikehata, M; Sakai, S [Yokohama National University, Yokohama (Japan). Faculty of Engineering

1997-10-01

This is basically a technique wherein the wing element method is replaced by a surface vortex lattice method. A horseshoe vortex of unknown intensity and source surface of known intensity are distributed on the wing surface and, under conditions that the fluid will not cross the boundary, the intensity of horseshoe vortex circulation is calculated for the solution of the fluid field. For the simulation of a real ship in navigation, the required propeller revolution thrust is determined using the real ship resistance value and real ship thrust reduction factor estimated from a model ship resistance test by extrapolation. The calculation of propeller performance is conducted in the quasi-steady condition using the force of fluid working on one wing for each wing angle (with the wing rotated at the increment of 6 degrees), and the thrust and torque are determined using the averages of values obtained in one cycle. It is found that the torque value is overestimated in a considerable degree in the wing element theory. In the surface vortex lattice method, both thrust and torque values agree with experimental values mostly, and this method is found to be accurate enough as a navigation element calculation tool when many panels are considered. 4 refs., 5 figs., 1 tab.

Report of the expert committee on the biological clean technology. No. 1. subcommittee. ; Measurement method of aerofungi and surface pollution fungi. Baiorojikaru kurin gijutsutaikei chosa senmon iinkai hokoku. 1. ; Kuchukin/hyomen osenkin sokuteiho

Energy Technology Data Exchange (ETDEWEB)

1994-03-31

The measurement of the aerofungi and surface pollution fungi is different in the collection, culture, count, evaluation method and so forth, and therefore a method to be able to correspond to all cases is not yet established. At present, it is required for performing a measurement that it is well adapted to a limit and characteristics of the individual measurement instrument. The aerofungi and surface pollution fungi handled in this paper should be the bacteria and true fungi, and moreover a case to measure them as the bacteria particle and true fungi should be an object. In case of measurement, for all of the culture medium adjustment, transportation sampling and culture, the aseptic manipulation is indispensable. In case of to measure them as the particle of the microorganisms, a process of the culture and count of the colony coming into view is passed through. When the various samplers are used, it is required for confirming beforehand that the flow rate complied with the regulations is aspirated. A measurement of a concentration of the aerial floating microorganisms is greatly influenced by the meteorological condition, personnel, its activity state and so forth, and consequently it shows generally a violent fluctuation. 2 figs., 2 tabs.

Report on the evaluation of the development of the catalyst surface high accuracy quantitative analysis technology using electron spectroscopy; Denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki gijutsu no kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

An objective evaluation from a third party was conducted on the purpose, plan, execution method, achievement, etc. of a project 'The devilment of the catalyst surface high accuracy quantitative analysis technology using electron spectroscopy.' The purpose of the project is to make the relationing possible between the analytical results of the catalyst surface and the catalyst performance which has been so far difficult by heightening the accuracy of the catalyst quantitative surface analytical accuracy using the electron spectroscopy. The purpose and significance are judged to be worth a lot. This project is an industry/university/government joint project between the two countries. The project is excellent both in connection among research institutes and leadership of chief researchers, and it is judged that the joint research system fully functioned. The term of the project was shortened from 3 years in the first plan to 2 years, and therefore, the study was finished only on silicon oxide and organic thin films. However, it was determined that the study results are to be run in the magazine 'Surface and Interface Analysis,' which indicates that the achievement was judged to be very worth in the academic viewpoint. (NEDO)

Effect of Al content on critical CTOD properties in heat affected zone of C-Mn microalloyed steel. Teitanso teigokin koyosetsu netsu eikyobu no genkai CTOD tokusei ni oyobosu Al ganyuryo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Fukada, Y.; Komizo, Y. (Sumitomo Metal Industries Ltd., Osaka (Japan))

1992-08-05

Two types of molten alloys specimen with a base of 0.10%C-0.20%Si-1.40%Mn-0.01%Ti system and varied Al content, were studied. The critical crack tip opening displacement(CTOD) properties in heat effected zone(HAZ) of extreme low Al content steel was stable at. extremely low temperature and there was no formation of M-A. Fine ferrite has a texture of [alpha] main body and it has been thought that the the change in the CTOD properties with the variation in Al content has been due to the difference in the texture. In case of Al content steel plate, the interfacial energy has been decreased due to excessive carbon concentration at [gamma] /[alpha] interface, M-A formation has been easier by the suppression of [alpha] transformation. In case of extremely low Al content steel plate, [alpha] transformation has been promoted and cementite deposition has been estimated from a small amount. of left [gamma] of extremely high carbon concentration. As for SH-CCT diagram of extremely low Al content steel plate, compare to Al content steel plate, [alpha] noze has shifted toward shorter time and formation of [alpha] has been easier within the normal welding cooling rate, and microstructures of [alpha] texture have formed in HAZ. 21 refs., 12 figs., 1 tab.

Study on the performances of handling and stability influenced by the differential terms in the state variables; Soansei ni okeru jotai hensunai no bibun yoso ga seino ni oyobosu eikyo no kento

Energy Technology Data Exchange (ETDEWEB)

Sugasawa, F [Tamagawa University, Tokyo (Japan); Mori, H [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

The analysis method using the system matrix for state variables can not be applied to the analysis for the system has Complex Cornering Stiffness. The reason is there are differential terms in the state variables. It is found that the differential terms m the state variables can be changed to the constant terms in another state variables. 4 refs., 9 figs.

Surface flaw detection by means of infrared radiometer. Part 3. ; Detection limit influenced by an environment temperature. Sekigai hoshakei ni yoru hyomen kekkan no kenshutsu. 3. ; Shuhen ondo ni yoru kenshutsu genkai no eikyo

Energy Technology Data Exchange (ETDEWEB)

Okamoto, U; Kaminaga, F [Ibaraki University, Ibaraki (Japan). Faculty of Engineering; Ishii, T [Ibaraki University, Ibaraki (Japan); Eto, M; Ooka, N; Kanaya, K; Eto, Y [Japan Atomic Energy Research Institute, Ibaraki (Japan); Kurokawa, T [Nippon Denki Sanei Ltd. Co., Tokyo (Japan)

1990-12-20

Measuring a radiation energy distribution around surface flaw by means of a infrared rediometer can detect fine flaw on the surface. The characteristics were examined using a light quantum type radiation thermometer consisted of Hg-Cd-Te as a sensor. A surrounding wall consisted of a black body wall was installed between the sensor and test piece, and by thus maintaining the surrounding wall temperature constant, reflection energy from the test piece surface was maintained constant for stabilized measurement. The measurement values are the sum of energies from emission and reflection, or the so-called radiosity values. To avoid effects from the reflection to reduce variance in the emissivity, it is necessary to keep the surrounding wall temperatures lower by more than 20 {degree}C than the test piece radiation temperatures. Emissivity can be calculated from the rediositivity (sum of the radiation and the reflection), the surrounding wall temperatures, and the test piece radiation temperatures. If the surface is rough, variance in the measurements increases. The larger the difference in the test piece and surrounding wall temperatures, the thermo image of the defects on the test piece surface becomes more distinctive, thus the detection limit can be enhanced. 7 refs., 13 figs.

Development of hydriding alloys with multi-functionally-graded properties and their applications to energy conversion devices; Keishagata fukugo kino wo hyomen ni motsu suiso kyuzo gokin no kaihatsu to energy henkan gijutsu eno oyo

Energy Technology Data Exchange (ETDEWEB)

Suda, S; Kadoma, H; Nagamoto, H; Okura, T [Kogakuin University, Tokyo (Japan)

1997-02-01

This paper describes the formation of fluoride layer on the surface of hydriding alloys. The fluoride formation reaction consists of a reduction removal process of surface oxide and a fluorination process. Specific surface area of alloy grains can be increased by the hydrogenation reaction in the surface layer accompanied with the removal of surface oxide, which results in easier permeation of molecular hydrogen into fluoride layer. During the fluorination process, a large amount of Ni in the alloy components is eluted, which results in the reduction of Ni distribution immediately under the fluoride layer in the alloy. Consequently, collector sites near the surface are reduced, and conductivity among alloy grains is degraded. To enhance the hydrogen collector sites, specific surface area of alloy grains can be increased by controlling the pH value of fluorination treatment solution in a given range. Moreover, performance of fluoride layer can be advanced by electrochemically dispersing metal Ni in the fluoride layer using Ni complex ion mixed in the treatment solution. 2 refs., 3 figs.

Effects of sand compaction pile (SCP) driving on the strength of clay outside the improved area; Sand compaction pile no dasetsu ga jiban kairyo ikigai no nendo jiban no kyodo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Matsuda, H. [Yamaguchi University, Yamaguchi (Japan); Takahashi, S. [Ministry of Transport, Tokyo (Japan); Fujiwara, K. [Penta-Ocean Construction Co. Ltd., Tokyo (Japan); Kitayama, N. [Fukken Co. Ltd., Hiroshima (Japan)

1998-06-21

This paper describes effects of the disturbance by the sand compaction pile (SCP) driving operations on the shear strength of clay outside the improved area and the border of region affected by the SCP driving. About 1,400 soil specimens were taken before and after the SCP driving inside and outside the improved area during the foundation improvement at Tokuyama-Shimomatsu Port in Yamaguchi Prefecture. Soil test data of the specimens and strength characteristics of disturbed clay specimens were investigated through the laboratory experiments. The results obtained are as follows. According to the multi-directional simple shear test results, the shear strength immediately after the cyclic shear decreased in 10 to 30% compared with that before the cyclic shear. When recompaction was conducted before the cyclic shear, however, it increased in 50% compared with that before the cyclic shear. The strength of clay decreased by the SCP driving even outside the improved area. When the internal frictional angle of clay, friction coefficient of the improved boundary and driving depth of SCP were determined, it was possible to estimate an area affected by the SCP driving using a combined sliding plane. 21 refs., 18 figs.

Effect of aluminum on the growth and nutrient uptake in cryptomeria japonica D.Don and Chamaecyparis obtusa Sieb. et Zucc.; Sugi oyobi hinoki no ikusei to yobun kyushu ni oyobosu aluminium no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kono, Y; Matsumura, H; Kobayashi, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1995-09-10

Two-year-old seedlings of Sugi (Japanese cedar: Cryptomeria japonica D. Don) and Hinoki (Japanese cypress: Chamaecyparis obtusa Sieb. et Zucc.) were grown for 4 months in 1/5 Hoagland`s No.2 nutrient culture solution containing aluminum chloride in the concentration range of 0.5 to 20 mM within the pH range of 3.5 to 4.0. Aluminium supplied at or below 1 mM of Al had no effect on the mortality of these species. However, the increase Al concentration higher than 2 mM increased the mortality. While they showed significant growth reduction at or higher Al concentration of 5 mM, there were no difference in growth response to Al between the two species in this experiment. While Al contents in leaf and root significantly increased with increasing Al concentration in the solution, contents of Ca, Mg and P in leaf decreased. Roof p content in Sugi increased with the increase of Al concentration in the solution, while no such change was observed in Hinoki root. This result suggests that Al might make phosphate immobile or inviolable form in Sugi root and this might lead to the reduced translocation of P into the leaf. In contrast, Al did not interfere with the uptake of phosphate in the root, however, it might interrupt phosphate transport into leaf from root system in Hinoki. The Al concentration such as 5 mM in the root sphere induced growth reductions in Sugi and Hinoki, with no significant difference in the response between the two species. This concentration was much higher than those reported in the field crops, vegetables and/or herbs. Thus, if soil acidification will be induced by acidic deposition in future, these herbaceous plants will be influenced faster than the conifer trees. This also means that ground vegetation change will be observed earlier than the conifer decline by the soil acidification stress. 23 refs., 5 figs., 3 tabs.

Effects of types of work and visual environemnt on human pschology and behavior in an office space. Shikankyo ga shitsumusha no shinriter dot kodo ni oyobosu eikyo sagyo naiyo no chigai ni yoruhyoka

Energy Technology Data Exchange (ETDEWEB)

Sato, M [The Tokyo Electric Power Co. Inc., Tokyo (Japan); Inui, M., Nakamura, Y. (Tokyo Institute of technology, Tokyo (Japan))

1991-10-30

In this paper, was investigared an effect of work and visual environment types on the psychology and behavior of workers in office spaces in terms of subjective appraisal, work performance, behavior pattern, etc. In order to make a such effect of visual environment clear, a series of factorial experiments were conducted. Window and interior decoration of pot plants and paintings were adopted as factors of the visual environment. A Krepelin addition, a Krepelin addition-subtraction and multiplication, a Krepelin machiene, a hand-written manoscript, a word-processed manuscript, and a mirror tracing were adopted as work types. The number of sobjects was five for each work type. Consequently, a significance of the effect of the window and interior decoration on workers was verified. It was also found that the presence of the window and interior decoration improved the work performance for the major types of perfomance test. Furthermore, it was revealed that the presence of the window ans interior decoration the behavior of subjects active. 11 refs., 11 figs., 9 tabs.

Fiscal 1999 international cooperation project report. Development of high-precision quantitative analysis technology for catalyst surfaces by electron spectroscopy; 1999 nendo denshi bunkoho ni yoru shokubai hyomen koseido teiryo bunseki bijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project targets to make analysis of surface chemical phenomena of solid catalysts possible, and establish the basis of intelligent design for catalytic materials, through development of an advanced electron spectroscopy for surface analysis. In fiscal 1999, the research was promoted by using the diffraction grating and driving mechanism introduced in fiscal 1998, and by developing the measurement result on silicon oxide films by radiation beam photoelectron spectroscopy. The measurement technique was established by the optimized measurement process which can treat variable parameters as constant. The analysis result of measurement data in fiscal 1999 showed the dependence of an electron damping length in silicon oxide films on radiation photon energy. The energy dependence well agreed with a theoretically obtained inelastic mean free path of electrons qualitatively, while was smaller by nearly 30% than the latter quantitatively. Measurement was made on the damping length in oxidation-active Gd and Nd oxide films. In both cases of Si and Si oxide film substrates, oxidation of substrates or formation of silicate was observed. (NEDO)

Study on the change of aspect ratios of small surface cracks emanated from a toe of corner boxing; Mawashi yosetsudome tanbu kara hassei denpasuru bishi bisho hyomen kiretsu no aspect hi henka ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Toyosada, M; Yamaguchi, K; Takeda, K; Watanabe, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1997-10-01

The fatigue test of specimens with a stiffener was carried out to examine the change in aspect ratio (crack depth/length) of fatigue cracks in a stress concentration field and residual stress field. The aspect ratio of surface cracks just after generation can be represented with the single virtual surface crack with the same value as K value at the deepest point considering an interference effect from near cracks. No discontinuous change in K value is found at the deepest point even during growth and combination of cracks on a surface. The change in K value at the deepest point is thus the criterion to represent growth and combination of surface cracks considering the interference effect. The change in aspect ratio of the typical single virtual surface crack linearly decreases with an increase in crack depth. The shape of surface cracks generating and growing in a residual stress field is more flat than that in no residual stress field. In addition, in a residual stress field, surface cracks are longer at the same crack depth, and fatigue lives are shorter. 7 refs., 12 figs.

Fiscal 2000 survey report. Development of autonomous surface reforming technology by use of multi-energy laser (MEL); 2000 nendo taju ihacho laser (MEL) ho ni yoru chokoshitsumaku no jiko hyomen kaishitsu gijutsu no kaihatsu chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An experiment was conducted using a MEL (multi-energy laser) method in which multiple laser devices were operated for the formation of an ultra-hard surface reformed layer. At the first step of the research, a carbon-based material was irradiated with various laser beams in an CO2 gas atmosphere, and the hardness, Raman spectrum, etc., of the surface structure were evaluated. As the result, it was found that the formation of diamond like carbon (DLC) texture advances faster when the excited wavelength is longer from ArF laser toward SHG-YAG laser. At the second step, an effort was made to grow DLC out of tungsten carbide. When a normal pulse YAG laser beam was projected on a WC-Co substrate, W was dissociated on the surface for the precipitation of graphite. Next, XeCl excimer laser was projected on the precipitated graphite, and then the graphite was reformed into DLC. In this experiment, transition from graphite to DLC was controlled by changing the delay time lengths of the two laser beams. (NEDO)

NAL-Tokyo Institute of Technology: Oxygen concentration on the surface of the solid, C[sub 6]0 are used, and it succeeds in the measurement. Kotai hyomen no sanso nodo, C[sub 60] mochii sokuteini seiko

Energy Technology Data Exchange (ETDEWEB)

1998-12-31

NAL succeeded in oxygen concentration measurement on the surface of the solid which fralen (C[sub 6]0) which was the same base body in cooperation with Tokyo Institute of Technology, biotechnology course as to carbon was used for fralen absorbs light, and materiality to be returned in the condition (base bottom condition) of the place by this activated condition's reacting for the activated condition with oxygen is used. The condition that became of this fralen was used, and oxygen pressure (concentration) developed how to measure it. Oxygen pressure on the surface of the irradiation is measured the light with applying fralen on the surface of the measurement solid and spraying oxygen gas on the application side. So far, 100 points and more of holes were made on the surface of the model, and a pressure sensor was installed, and pressure measurement was being done, and it was as it were the measurement of the meeting body of the point in the aircraft and the wind experiment of the rocket model. The application of fralen, light only irradiates it, and oxygen pressure can be measured easily in the way of measuring it this time. Moreover, it is the measurement of the non-contact and non-destruction side. The illuminant, which makes fralen activated condition again, is sufficient with the visible light, and it is said that it doesn't need to use purple outside light about it. If light can irradiate it again, the surface pressure of which part can be measured, too. (translated by NEDO)

NAL-Tokyo Institute of Technology: Oxygen concentration on the surface of the solid, C{sub 6}0 are used, and it succeeds in the measurement; Kotai hyomen no sanso nodo, C{sub 60} mochii sokuteini seiko

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

NAL succeeded in oxygen concentration measurement on the surface of the solid which fralen (C{sub 6}0) which was the same base body in cooperation with Tokyo Institute of Technology, biotechnology course as to carbon was used for fralen absorbs light, and materiality to be returned in the condition (base bottom condition) of the place by this activated condition`s reacting for the activated condition with oxygen is used. The condition that became of this fralen was used, and oxygen pressure (concentration) developed how to measure it. Oxygen pressure on the surface of the irradiation is measured the light with applying fralen on the surface of the measurement solid and spraying oxygen gas on the application side. So far, 100 points and more of holes were made on the surface of the model, and a pressure sensor was installed, and pressure measurement was being done, and it was as it were the measurement of the meeting body of the point in the aircraft and the wind experiment of the rocket model. The application of fralen, light only irradiates it, and oxygen pressure can be measured easily in the way of measuring it this time. Moreover, it is the measurement of the non-contact and non-destruction side. The illuminant, which makes fralen activated condition again, is sufficient with the visible light, and it is said that it doesn`t need to use purple outside light about it. If light can irradiate it again, the surface pressure of which part can be measured, too. (translated by NEDO)

Effect of pore water pressure on P-wave velocity in water-filled sands with partial air saturation; Fukanzen howa jotai no suna shiryo wo denpasuru P ha sokudo ni oyobosu kangeki suiatsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kanema, T [Chishitsu-Keisoku Co. Ltd., Tokyo (Japan)

1997-10-22

With an objective to elucidate change in velocity of elastic waves in association with water pressure increase in a sand bed below the groundwater level in a shallow portion of the ground, a measurement experiment was carried out on P-wave velocity in sand samples with partial air saturation. The experiment has used fine sand having an equivalent coefficient of 2.40, a soil particle density of 2.68 g/cm {sup 3} or 60%, and a grain size of 0.36 mm. Inside the water-filled sand sample, two accelerometers were embedded 20 cm apart from each other as vibration receivers. An electromagnetic hammer for P-wave was used as the vibration source. In the experiment, measurement was carried out on the P-wave velocity in association with increase in pore water pressure by applying water pressure afresh to the water-filled sample. As a result of the experiment, the following matters were disclosed: the P-wave velocity increases as the pore water pressure was increased, and a phenomenon was recognized that the dominant frequency changes into high frequency; the degree of increase in the P-wave velocity varies depending on initial saturation of the sample; and bubbles in the pore fluid have their volume decreased due to compression resulted from increased pore water pressure and dissolution of air into the pore water. 6 refs., 11 figs.

Effects on annual cost of solar/air-heat utilization system of carbon tax and interest rate for a residential house; Jutakuyo taiyo/taikinetsu riyo system no nenkan keihi ni oyobosu tansozei kinri no eikyo

Energy Technology Data Exchange (ETDEWEB)

Shen, Q; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan). Faculty of Engineering

1996-10-27

In recent years, a system has been proposed that utilizes river heat, air-heat, exhaust heat from a cooler, etc., in addition to natural energy for the heat pump. With the introduction of such system, the amount of energy used and that of CO2 exhaust will be greatly reduced, but annual expenses will be increased as it stands. In order to improve the cost efficiency of the system, a proposal has been made for the introduction of an economic policy such as the carbon tax and a low interest financing system. With these matters in the background, the subject study predicts the production of solar cells in the future and, on the basis of this production, determines the price, conversion efficiency and equipment energy of solar cells in the future. Using these values and taking into consideration the introduction of the carbon tax and the low interest financing system, the optimum area was determined for solar cells and heat concentrators in a future residential solar/air-heat energy system. The carbon tax, being imposed on all CO2 discharges, had a large effect. Moreover, as the tax increased, annual expenses decreased for the solar/air-heat system. 3 refs., 6 figs.

Degradation and stabilization of coal derived liquid. (IV). ; Effect of alcohol on coloration of coal derived light oil. Sekitan ekikayu no anteika. (IV). ; Sekitan ekikayu no chakushoku yokusei ni oyobosu alcohol no tenka koka

Energy Technology Data Exchange (ETDEWEB)

Ukegawa, K.; Matsumura, A.; Kondo, T. (National Research Institute for Pollution and Resources, Tsukuba (Japan)); TAhara, N. (Nitto Denko Corp., Osaka (Japan)); Nakamura, E. (New Energy and Industrial Technology Development Organization, Tokyo (Japan)); Niki, E. (The University of Tokyo, Tokyo (Japan). Research Center for ADvanced Science and Technology)

1990-01-20

In order to improve the color stability of a coal derived light oil, the effect of hydrotreating and various additives has been studied. The color stability has been evaluated through measuring changes in absorbance by flow-cell spectrophotometer. Following results have been obtained: The color stabilities of hydrotreated coal derived light oils were improved remarkably with increasing hydrotreating temperature and pressure. Mild hydrotreating made the color stability of the coal derived light oil much better than the fuel oil, even though the nitrogen removal was very small. Phenolic compounds additives could not improve the color stability of the coal derived light oil. Alcohol, especially methanol, made the coloration rate of the coal derived light oil small to a great extent, on account of hydrogen bonding between methanol and nitrogen compounds in the fuel oil. 4 refs., 4 figs., 3 tabs.

Reproductive and offspring developmental effects following maternal inhalation exposure to methanol in nonhuman prinates; Methanol no kyunyu bakiuro ga hi hito reichoryi no bosei no seisho ku to kodomo no seicho ni oyobosu eiky

Energy Technology Data Exchange (ETDEWEB)

Suzuki, T [Japan Automobile Research Institute Inc., Tsukuba (Japan)

2000-04-01

The paper summarizes the results of the experimental study on effects of the long-term exposure to methanol on the metabolism and reproduction of grown-up female Macaca and effects of monkeys exposed to methanol in a period of the unborn baby on the development. In this study, grown-up female monkeys (11-12 in each group) were exposed to methanol vapor of concentration 4 (0, 200, 600, 1800ppm) for 2.5 hours/day, for 7 days, and in each period of pre-breeding/in-breeding/in-pregnancy. The concentration of methanol and folic acid in blood was measured, and changes caused by repeated methanol exposures were evaluated which relate to internal dynamic states (inhalation, dispersion, metabolism and excretion) and pregnancy. Also evaluated were the development in the first 9 months after birth of infant monkeys (8-9 in each group) at high concentration and the nervous action development. As a result, there were found no evidences of giving marked effects such as effects of the methanol concentration in blood, formate concentration, folic acid concentration, and internal dynamic states of the pregnant animal, and effects of the methanol exposure before birth on nervous actions of children of nonhuman primates. (NEDO)

Effect of temperature on degradation of musty odour compound producing by cyanobacteria, Phormidium tenue by microflagellate, Monas guttula; Benmochu Monas guttula ni yoru kabishu sansei sorui Phormidium tenue no bunkai ni oyobosu ondo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Lee, B.; Sudo, R. [Tohoku University, Sendai (Japan). Faculty of Engineering; Sugiura, N. [Ibaraki Prefectural Waterworks, Ibaraki (Japan); Inamori, Y.; Nishimura, O. [National Inst. for Environmental Studies, Tsukuba (Japan); Higashi, T. [University of Tsukuba, Tsukuba (Japan). Institute of Applied Biochemical

1998-04-10

Biodegradation characteristics of cyanobacteria, Phormidium tenue and its metabolites, 2-methylisoborneol (MIB) by protozoan microflagellate, Monas guttula, and the effect of temperature on them were examined in batch culture experiment. The flagellate was found to predate on P. tenue favorably as a food source within a wide temperature range from 10degC to 30degC. Specific growth rate ({mu}) and generation time (t{sub d}) of the flagellate were 4.6 day{sup -1} and 3.5 h{sup -1}, respectively at 20degC and 30degC, whereas in the case of 10degC the lag values of {mu} and t{sub d} were obtained by 1.9 fold in comparison with the removal ratio of 61% at the first cultivation day and that of 99% at the 2nd day at 30degC, while at 20degC the removal was only about 30% in the first day, but P. tenue could be perfectly reduced at the 2nd day. Although the reduction rate of the P. tenue was slow at the lower temperature of 10degC, the removal reached 98% in the 7th day. Removal rate of P. tenue by the flagellate increased with the increase in temperature and reached the maximal value with 4.0 h{sup -1} at 30degC. The flagellate could contribute to the degradation of MIB, although the degradation was lower than that of P. tenue. It was found that the microflagellate could favorably predate on P. tenue and degrade its metabolite, MIB emitting musty odor in a wide range of temperature. 27 refs., 8 figs., 3 tabs.

Research and development of photovoltaic power system. Characterization and control of surface/interface recombination velocity of crystalline silicon thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Silicon kessho usumaku ni okeru hyomen kaimen saiketsugo sokudo no hyoka to seigyo

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, H [Hokkaido University, Sapporo (Japan). Faculty of Engineering

1994-12-01

This paper reports the result obtained during fiscal 1994 on characterization and control of surface/interface recombination velocity of crystalline silicon thin films. To optimize design and manufacture of solar cells, it is necessary to identify correctly resistance factor (or doping) of bulk of materials, bulk minority carrier life, and recombination velocity on surface, passivation interface and electrode interface. A group in the Hokkaido University has been working since a few years ago on development of non-contact and non-destructive photo-luminescence surface level spectroscopy (PLS{sup 3}). A new non-contact C-V method was also introduced. Using these methods, basic discussions were given on possibility of separate measurements on surface/interface and bulk characteristics of solar cell materials. The PLS{sup 3} method and the non-contact C-V method were used for experimental discussions on evaluation of silicon mono-crystalline and poly-crystalline materials. Discussions were given on separate evaluations by using the DLTS method. 10 figs., 2 tabs.

Experimental and numerical studies on aerodynamical noise in a high-speed elevator. ; Effect of apron on flow around elevator car. Kosoku elevator no kuriki soon ni kansuru kenkyu. ; Kagomawari no nagare ni oyobosu apron bu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Matsuda, H.; Fukuyama, Y.; Miyasako, K.; Endo, M. (Toshiba Corp., Tokyo (Japan)); Yokono, Y. (Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Precision Machinery and Electronics)

1993-08-25

For the purpose of reducing aerodynamic noise of a high-speed elevator, the flow around the elevator car was subjected to a flow visualization experiment and numerical simulation using a model simulating an elevator. The state of the flow in front of the door was observed by visualizing the field of flow around the model submerged in a water bath using a poster color tracer. Further, a wind tunnel experiment was carried out to observe the effects of flow at the side wall of the car. An oily agent using TiO2 as pigment was used for observing the pattern of oil film on the surface of the model and the observed results were recorded on a video tape. Since the oil solution is white, the place where the oil film is peeled by a strong shearing force exhibits a pattern of black color which is the color of the model substrate. Flow in front of the door is different depending on whether the car is in the upward motion or in the downward motion and affected by the presence of apron. During the downward motion of the car, the vertical vortices accompanying the flow detouring from the rear surface to the front surface of the apron are generated at both ends of the apron and thereby the streamlines are concentrated to generate accelerated flow in front of the door. Suppression of vertical voltices is important for reducing noise during downward motion. Peeled flow and vortex interference appear at the side and back of the car and forms a field of complex flow. 12 refs., 10 figs.

CFD prediction of heat island formation on growing Asian cities. Effect of urbanization in Shanghai; Kyodaikasuru Asia no toshi ni okeru heat island keisei ni kansuru CFD yosoku. Shanghai no toshika ga oyobosu eikyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ojima, T.; Murakami, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Mitsumoto, K. [Waseda University, Tokyo (Japan). School of Science and Engineering

1997-10-01

Study is conducted of the effect of change in land use and increase in artificial exhaust heat on heat island formation in Shanghai. Concerning the land use distribution in Shanghai, a point sampling survey was conducted in the 1930s using topographic charts, when the area was broken down into building-occupied region, paddy field, bare ground, and waters. In the 1990s, thanks to data from satellites, high-density and low-density urban regions have added. Calculation for Shanghai is performed, based on the rate of increase in Tokyo`s population and data predicted for Shanghai`s population, on the assumption that Shanghai`s population in the 2050s will grow 2.3 times larger than it is in the 1990s. The prediction thus produced indicates that the urban area in Shanghai in the 2050s will be as large as that of the present-day Tokyo that covers a 50km zone. Heat island formation prediction for Shanghai is worked out using computational fluid dynamics (CFD)-aided simulation. According to the prediction, while the maximum temperature in the 1930s was 29.6degC or 4degC higher than in the suburbs, it is 33.2degC or 7.6deg higher in the 1990s, and will be 34.4degC or 8.6degC higher in the 2050s. 16 refs., 11 figs., 1 tab.

Effects of air pollution on the health of regional inhabitants. Part I. Survey of disease state by Enquete. Taiki osen ga chiiki jumin no kenko ni oyobosu eikyo ni tsuite-dai ippo; anketo ni yoru shojo chosa

Energy Technology Data Exchange (ETDEWEB)

1973-01-01

From May to July 1972, the disease states of 2096 inhabitants (710 men and 1386 women) in the Fukushima Ward of Osaka City, where the concentration of sulfur trioxide in the air was (yearly average) 1.81 mg/day/100 sq cm and that of carbon monoxide was 5.3 ppM, and that of nitrogen dioxide was 5.3 ppM, were surveyed. The number of persons surveyed was 2.9% of all the inhabitants of the Ward. Twenty-two point one percent were in their thirties, 20.1% in their forties, 16.5% in their sixties, and 15.3% in their fifties. Those who experienced chest diseases were 2.9% of the total, and those with heart diseases were 1.5%. Non-smoking men were 31.7% of the total. The percentage of long-term complaints of cough and sputum was 11.8% in the eastern section, 11.2% in the northern section, 10.0% in the southern section, 6.8% in the western section of the Ward. The frequency of complaints was highest in the sixties (12.7%), followed by 11.5% in the fifties, 11.3% in the thirties, and 8.6% in the forties. The frequency of complaints from men was 11.1% and that from women was 6%. The frequency of complaints was 19.8% in smokers, 8.5% in those who smoked less, and 6.8% in non-smokers. The frequency of complaints classified by residential area showed 12.6% in industrial areas, and 7.8% in residential and commercial areas. The frequency of complaints of inhabitants who live along National Road No. 2 was relatively high, ranging from 15.0 to 18.8%, and the frequency of complaints of inhabitants was apparently higher than those of people who only work in the Ward.

FY 1995 development of fluorinated hydriding alloys with multi functional and functionally-graded surface and their application to energy conversion devices; 1995 nendo keishagata fukugo kino wo hyomen ni motsu suiso kyuzo gokin no kaihatsu to energy henkan gijutsu eno oyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The project is the extended researches of a fluorination technique invented by the project leader (Suda) for improving the surface properties and characteristics of conventional hydriding alloys from the following viewpoints; (1) To investigate the roles of fluorinated surface during hydrogen uptake both in the gas-solid and the electrochemical reactions. (2) To elucidate the factors which increase the protective nature of the surface. (3) To develop a material design procedure for synthesizing thin layer of functionally graded surface which is composed of metallic Ni and the fluoride compound. (1) An advanced fluorination technique was developed to incorporate metallic Ni in the surface fluoride layer. (2) Metallic Ni was successfully distributed in a functionally graded manner in the Surface fluoride layer. (3) Through the technique developed, the following properties and characteristics were successfully donated in the fluorinated hydriding alloys such as AB{sub 5}, AB{sub 2}, and AB; (3-1)Surface oxides which act as the resistant layer to the hydrogen up take was completely eliminated to result in the enhancement of the initial activation characteristics. (3-2) Hydrogen selectivity and permeability was greatly improved. (3-3) Surface protective nature against the impurity gases and contaminants was significantly improved. (3-4) Initial activation characteristics both in the gas-solid and the electrochemical reactions were distinguishably improved. (3-5) Fluorinated surface was found to function as the catalyst for a methanation reaction between the CO{sub 2} gas adsorbed over the fluorinated surface and the monatomic hydrogen absorbed in the metal lattice of the crystalline structure of the hydriding alloys. (4) A technique was developed for increasing the specific surface area and decreasing the specific surface diameter of the fluorinated hydriding alloy articles. (NEDO)

Effects of variation of flow and accumulation of suspended solids on the performance of anaerobic/aerobic biofilm system applied to grey water treatment. kenkiter dot koki roshoho no shori seino ni oyobosu ryuryo hendo oyobi kendaku busshitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Okubo, T; Sagehashi, M; Otsuka, N; Okada, M; Murakami, A [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1991-04-10

In this study, effects of variation of flow and accumulation of suspended solids (SS) on the performance of anaerobic/aerobic biofilm system were investigated through the laboratory test using synthetic wastewater and the field test using grey water. Effects of flow variation scarcely appeared on the time change of effluent quality in both cases where daily average hydraulic retention time (HRT) in anaerobic filter was 20h and that of aerobic filter was 6.7h. In the field test, however, removal rate of organic substances was lower (20-30%) than that of the laboratory test (90%), since SS content in grey water accumulated in the anaerobic filter which led dissolution of organic substances from accumulated SS, blocking, and short-circuit flow. Moreover, it was confirmed by the batch test that constituent of grey water has lower resolution for microorganisms and is more difficult to nitrate than synthetic waste water. 24 refs., 11 figs., 4 tabs.

Effect of volume change of coal during plastic and resolidifying phase on the internal gas pressure in coke ovens; Sekitan nanka saikoka katei ni okeru taiseki henka ga cokes ro no nanka yoyu sonai gas atsu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Nomura, S; Arima, T [Nippon Steel Corp., Tokyo (Japan)

2000-08-01

The coking pressure in coke oven, which is caused by the internal gas pressure in the coal plastic layer, is determined by the gas permeability of the layer. The gas permeability of the plastic layer depends on its density as well as the physical property of the plastic coal itself The plastic layer is between the coke layer and the coal layer and the effect of the volume change of these outer layers, i.e. contraction and compression, on the density and the internal gas pressure of the plastic layer was studied. Sandwich carbonization test, where different coals were charged in the test coke oven, showed that the internal gas pressure in the plastic layer depends not only on the one kind of coal in plastic phase but also on the other kind of coal in resolidifying phase near the oven walls. The relative volume of coke transformed from the unit volume of coal was measured using X-ray CT scanner and it varied greatly across the coke oven width depending on the kinds of coals. The volume change of coal during plastic and resolidifying phase affects the density and the internal gas pressure of the plastic layer The relative volume of semicoke and coke transformed from the unit volume of coal near the oven walls is higher for a high coking pressure coal than that for a low coking pressure coal. This leads to the high density of the plastic layer and the generation of dangerously high internal gas pressure in the oven centre. (author)

Emission characteristics of premixed lean diesel combustion. Effects of injection nozzle and combustion chamber shape on combustion and emission characteristics; Kihaku yokongo diesel nensho no haishutsubutsu tokusei. Funmu keijo oyobi nenshoshitsu keijo ga haishutsu gas tokusei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Harada, A; Sasaki, S; Miyamoto, T; Akagawa, H; Tsujimura, K

1997-10-01

Many articles about low NOx emission combustion are reported. A mixture formation is necessary to success low NOx emission combustion. But, there is few reports about the effect of nozzle and combustion shape on emissions which give influence on mixture. In this paper, the effects on characteristic of combustion and emissions of some land of injection nozzle and combustion chamber shape were investigated. As a result, it was cleared that the influence of combustion chamber shape on characteristic of combustion and emissions was varied by spray shape, and pintle type injection nozzle was suitable for PREDIC. 7 refs., 10 figs., 1 tab.

FY 1997 report on the research study on the effect of the active use of bio-technology on energy and social systems; 1997 nendo chosa hokokusho (bio-technology no katsuyo ni yoru energy shakai system ni oyobosu koka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For construction of a sustainable society by active use of bio-technology, a research study was made on the current state of active use of bio-technology for every industrial or social field, and the basic recognition and orientation for practice and diffusion of bio-technology. The previous typical examples of the effect of bio-technology on energy and social systems were evaluated from not only an affirmative viewpoint but also a compensatory viewpoint. Based on these examples, promising features of bio-technology and measures for active use of such features were showed for the future energy and social systems from a technological viewpoint. As a scenario for sustainable development of a society, some approaches and values about collection of rare resources, agriculture based on mass circulation, and recurrence to high-protein traditional foods such as fermented food were showed for balanced development of environment, population, and resources including energy and food. 8 refs., 14 figs., 8 tabs.

Studies on the catalysts for coal liquefaction. ; Specific behaviours of coals of different ranks in their hydrogenolysis reactions catalyzed by various kinds of catalysts. Sekitan ekikayo shokubai ni kansuru kenkyu. ; Suisoka bunkai seiseibutsu sosei ni oyobosu kakushu shokubai no koka

Energy Technology Data Exchange (ETDEWEB)

Takechi, Y; Ikenaga, N; Oda, H; Yokokawa, C [Kansai University, Osaka (Japan). Faculty of Engineering

1991-11-07

Three kinds of coals with different rank of 76, 85 and 87C% were hydrocracked to study the specific reaction behavior of four kinds of 1coal liquefaction catalysts such as CuCrO4, Fe2O3+S, MoO3-TiO2 and MoS3-Al2O3. The reaction was conducted without any solvent to find out the specific phenomenon of each combination of coal and catalyst, and terminated at the point where nearly 30% of an initial amount of coal is converted to benzene-soluble. The products were separated by GPC into four fractions, and their average molecular weights and intrinsic viscosities were measured to study characteristics of each combination. As a result, the molecular weight distribution was obviously dependent on the combination of coal and catalyst, and no specific relation was observed between the molecular weight and intrinsic viscosity. The molecular of each fraction had a bar shape with an elliptic section indicating no apparent correlation with the molecular weight. 3 refs., 1 figs., 2 tabs.

Solid/liquid phase change heat transfer in porous media. Effect of density inversion of water on melting process in a rectangular region; Takoshitsu sonai no ko-ekiso henka. Mizu no mitsudo gyakuten ga kukei ryoiki no yukai katei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Sasaguchi, K [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

1994-12-25

Solid/liquid phase change in porous media has a wide relation with freezing and melting of ground bed, storage of cold heat in soil, and underground heat exchangers. This paper describes an investigation on the effect of density inversion on melting of ice in porous media by using the previously reported numerical analysis method. The high-temperature side temperature and the Darcy number were varied and investigated systematically on the ice in a porous media sealed in a rectangular container of which right hand side is maintained at elevated temperatures and the other three sides are insulated of heat. As a result, a large number of findings were obtained including the following matters: when the Darcy number is fixed at 4.01 {times} 10{sup {minus}5} and the high-temperature side temperature, Tw, is varied, the fluid descends along the high-temperature side because of the density inversion at Tw=4{degree}C, and forms one weak circulation that rotates clockwise; however, when the temperature reaches 16{degree}C, the circulation disappears, and a circulation rotating counterclockwise is observed, becoming identical to the case of a fluid where there is no density inversion; and change in the Nusselt number against the melting ratio, R, is the smallest at Tw=8{degree}C, and decreases monotonously with the R. 15 refs., 12 figs.

Study on closed pressure vessel test. Effect of heat rate, sample weight and vessel size on pressure rise due to thermal decomposition; Mippeigata atsuryoku yoki shiken ni kansuru kenkyu. Atsuryoku hassei kyodo ni oyobosu kanetsusokudo, shiryoryo oyobi youki saizu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Aoki, Kenji.; Akutsu, Yoshiaki.; Arai, Mitsuru.; Tamura, Masamitsu. [The University of Tokyo, Tokyo (Japan). School of Engineering

1999-02-28

We have attempted to devise a new closed pressure vessel test apparatus in order to evaluate the violence of thermal decomposition of self-reactive materials and have examined some influencing factors, such as heat rate, sample weight, filling factor (sample weight/vessel size) and vessel size on Pmax (maximum pressure rise) and dP/dt (rate of pressure rise) due to their thermal decomposition. As a result, the following decreasing orders of Pmax and dP/dt were shown. Pmax: ADCA>BPZ>AIBN>TCP dP/dt: AIBN>BPZ>ADCA>TCP Moreover, Pmax was not almost influenced by heat rate, while dP/dt increased with an increase in heat rate in the case of BPZ. Pmax and dP/dt increased with an increase in sample weight and the degree of increase depended on the kinds of materials. In addition, it was shown that Pmax and dP/dt increased with an increase in vessel size at a constant filling factor. (author)

Study on a constant-tip-speed-ratio operation of wind power generation system. Effect of load control system on dynamic behavior; Furyoku hatsuden system no hensoku seigyo unten ni kansuru kenkyu. Fuka seigyokei ga system no rikigakuteki kyodo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Wakui, T.; Yamaguchi, K. [Waseda University, Tokyo (Japan); Tanzawa, Y. [Nippon Institute of Technology, Saitama (Japan); Hashizume, T.; Ota, E. [Waseda University, Tokyo (Japan). School of Science and Engineering

1998-06-01

The effect that the set data of the load control system in a wind power generation system exerts on the dynamic behavior of a system was investigated. The wind power generation system consists of a hybrid wind turbine with combined Darrieus and Savonius rotors, load with a generator and battery in the center, and a controller. A constant-tip-speed ratio operation that holds the circumferential speed ratio in which the power coefficient is maximized irrespective of the change in wind velocity was used to extract and convert the wind energy more effectively. In a high-wind velocity area, the system is operated at a fixed speed, and the increase in rotation is suppressed to protect the wing strength. In a large system, the response characteristics are only slightly improved by the limited load operation range and influenced rotor inertial. Power cannot be fully extracted even if the control system is changed in setting, and the applicability to the wind situation remains low. During the actual operation, the adjustment value of the control system should be set so that the output operation is satisfactorily possible in the specified load operation range, that is, the change in the instantaneous value of an effective power coefficient indicates almost flat gain characteristics in frequency characteristics. 14 refs., 10 figs., 2 tabs.

Research report for fiscal 1998. Development of advanced surface processing technology for methane-fueled aircraft engine members (Laser-aided advanced processing system technology); 1998 nendo chosa hokokusho. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (Laser oyo senshin kako system gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the research and development of erosion-resistant abradable materials for the methane-fueled aircraft engine front section, a laser-aided surface reform technology was developed for Ti alloys and the like. In relation with the article 'Intermetallic Compound Coating Formation Technology,' an NiTi sprayed coating containing excess Ni solid solution was found to be quite high in resistance to erosion, and similar to Ti-6Al-4V in resistance to oxidation at 300 degrees C. Furthermore, an MCrAlY erosion-resistant coating was formed capable of resisting oxidation at temperatures higher than 1000 degrees C. In relation with the article 'Spraying Phenomenon Evaluation Technology,' studies were made of combustion synthesis reaction during plasma spraying and of the prediction of flight trajectories of different powders, for which optical fiber dichroic temperature measuring, 2-dimensional imaging, and LDV (laser Doppler velocimetry) were applied in combination. Concerning the spraying of intermetallic compound coatings, a temperature rise occurred when heating by laser was performed simultaneously with the laser-induced combustion synthesis reaction. In relation with the article 'Technology of Multiple Spraying on Curved Substrate,' it was found that the gas cooled method works effectively when spraying an erosion-resistant coating onto a thin Ti alloy made turbine blade. (NEDO)

Relationship between concentration of surfactant and pressure for droplet creation, and effect on droplet size in microchannel O/W emulsification; Maikurochaneru ni yoru O/W nyukaho ni okeru kaimen kasseizai nodo to ekiteki seisei atsuryoku no kankei, oyobi koreraga ekitekikei ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kawakatsu, T.; Komori, H.; Oda, N.; Yonemoto, T. [Tohoku Univ., Sendai (Japan). Graduate School of Engineering

1998-03-01

O/W (oil in water) emulsion is produced by micro-channel emulsification method, and the effects of surfactant concentration on the pressures at which droplet generation starts and stops are evaluated in connection with the water phase and oil phase interfacial tension. In addition, the effects of surfactant concentration and operational pressure on the droplet size are investigated by measuring the generated droplet distribution, mean droplet size, standard deviation, geometrical standard deviation, and the possibility of producing mono-dispersion emulsion whose droplet size is large than 10 micron. The breakthrough pressure and the minimum pressure for droplet generation become low with the increase of SDS (sodium lauryl sulfate) concentration. The surfactant concentration, however, is found to have no effect on the breakthrough pressure and the minimum pressure for droplet generation when the SDS concentration exceeds the critical micelle concentration. It is true also for a system added with NaCl. As regards droplet size, uniform 20{mu}m droplet is obtained irrespective of the surfactant concentration and pressure. 13 refs., 10 figs., 2 tabs.

Mercury free zinc alloy powder for alkaline manganese battery. 2. Effect of additive species to zinc particle on suppressing hydrogen gas evolution; Arukari mangan denchiyo mukoka aen gokin funmatsu. 2. Suiso gas hassei ni oyobosu aen ryushi eno tenka genso no yokusei koka

Energy Technology Data Exchange (ETDEWEB)

Yano, M.; Fujitani, S.; Nishio, K. [Sanyo electric Co. Ltd., Osaka (Japan); Akai, Y.; Kurimura, M. [Sanyo Excell Co. Ltd., Tottori (Japan)

1997-08-05

In order to make alkaline manganese batteries mercury-free and suppress hydrogen gas generation, investigations were given on the effect of additive species on modification of zinc particles present on negative electrode surface. Mercury with high hydrogen overvoltage has been added conventionally, but the mercury can cause an environmental problem. Surface modification by using indium exhibited hydrogen gas generation suppressing effect. With the surface modification amount of 0.10% by weight or more, the suppressing effect is saturated, reducing the effect to 50% of that of mercury. Surface-modifying the bismuth added zinc particles with indium showed greater suppressing effect than the case where each element is used independently. Zinc-indium (0.10% by weight) - bismuth (0.025% by weight) based alloy powder showed the same hydrogen generation suppressing effect as zinc-mercury (0.15% by weight) alloy powder. A sealed test battery using this alloy powder in negative active material exhibited a discharge capacity of 1700 mAh similarly to the initial stage even after having been stored for 20 days at 60 degC. Self-discharge characteristics equivalent to that of zinc-mercury (0.15% by weight) based alloy powder were obtained. An environment compatible dry cell battery containing no mercury whatsoever was developed successfully. 18 refs., 6 figs., 1 tab.

Effects of melt-temperature on limiting current density in Al electrodeposition and morphology of Al electrodeposits obtained from ambient temperature type molten salt; Joongata yoyuen kara no denki aluminium mekki no genkai denryu mitsudo oyobi denseki keitai ni oyobosu mekki ekion no eikyo

Energy Technology Data Exchange (ETDEWEB)

Shimizu, T.; Tatano, M.; Uchida, Y. [Nisshin Steel Co. Ltd., Tokyo (Japan)

1996-03-31

Some of more important electrolytic solutions for Al electrodeposition are organic solvents, high-temperature type molten salts and low-temperature type molten salts having a melting point of 30{degree}C or lower, such as ethylmethylimidazolium chloride (EMIC). This study uses a molten salt of AlCl3-EMIC as the low-temperature type solution for high-speed electrodeposition. Discussed herein are the effects of melt temperature on limiting current density in Al electrodeposition and Al electrodeposit morphology. Limiting current density increases as melt temperature increases at any AlCl3 concentration used in this study. The AlCl3 concentration that gives the maximum limiting current density shifts from 64 to 67mol% at a melt temperature of 120{degree}C. A dense, smooth Al electrodeposited film results at a melt temperature of 100{degree}C or lower, but the electrodeposited grains become coarser as melt temperature increases. Melt temperature can be increased to 140{degree}C to secure a smooth electrodeposited film, showing possibility of 2 times faster electrodeposition than the conventional one. 21 refs., 12 figs., 1 tab.

Improvement of tribological properties of magnetic tape by silica coating onto the Co-{gamma}-Fe{sub 2}O{sub 3} fine particles; Kobaruto hichakugata {gamma}-Fe{sub 2}O{sub 3} jisei biryushi no shisshiki shirika hyomen shori ni yoru jikitepu no suberi tokusei no kaizen

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Kazuyuki; Iwasaki, Keisuke; Tanaka, Yasuyuki; Morii, Hiroko [Toda Kogyo Corporation, Hiroshima (Japan). R and D Center

1999-01-10

In order to improve the tribological properties of magnetic tape with Co-{gamma}-Fe{sub 2}O{sub 3} fine particles against a magnetic head, the silica coating onto the surface of Co-{gamma}-Fe{sub 2}O{sub 3} particles in aqueous slurry is investigated experimentally, and the kinetic friction coefficient of magnetic tapes prepared using the coated particles is measured. By this silica coating, the amount of myristic acid absorbed on the Co-{gamma}-Fe{sub 2}O{sub 3} particles tends to decrease and the kinetic friction coefficient of the magnetic tapes can be reduced from 0.4 to 0.2 because of the increase of the effective amount of myristic acid working as the lubricant when the magnetic tape is moving. Since the magnetic properties and the dispersibility of Co-{gamma}-Fe{sub 2}O{sub 3} pigment in the magnetic lacquer are not degraded by the silica coating, this coating method is expected to result in magnetic recording media with both good magnetic and low friction properties. (author)

Effects of lactic acid bacteria in kimoto on sake brewing. Part 2. ; Promotion mechanism of enzymolysis in rice by teichoic acid. Kimotochu no nyusankin no seishu jozo ni oyobosu eikyo. 2. ; Kimotochu no nyusankin ni yuraisuru teikosan no. alpha. kamai yokai sokushin sayo kisaku

Energy Technology Data Exchange (ETDEWEB)

Mizoguchi, H.; Tsurumoto, M.; Furukawa, A.; Kawasaki, T. (Kikumasamune Sake Brewing Co. Ltd, Hyogo (Japan))

1991-07-25

In order to elucidate promotion mechanism of dissolution of {alpha}-rice (pregelatinized rice) by teichoic acid. adsorption of teichoic acid and {alpha}-amylase onto rice protein oryzenin was investigated by experiments. Teichoic acid was adsorbed well onto oryzenin and reduced adsorption of {alpha}-amylase. Adsorption of {alpha}-amylase onto rice powder was decreased logarithmically in proportion to the teichoic acid added. Both teichoic acid and {alpha}-amylase were adsorbed by histone, abundant in basic amino acids, and by anion-exchange resin. Adsorption of {alpha}-amylase onto them was reduced by coexistence with teichoic acid. As the results of experiments, it was inferred that teichoic acid became dissolvable through autolysis by lactic acid bacteria in kimoto, changed the state of electric charge on oryzenin surfaces through adsorption onto oryzenin by phosphoric group, decreasing adsorption of {alpha}-amylase onto oryzenin and increasing free {alpha}-amylase in the liquid phase, and thus increased the dissolution of {alpha}-rice. 9 refs., 6 figs., 3 tabs.

Desolvation of L-histidine and {alpha}-ketoisocaproic acid complex from ethanolate crystals under humidified conditions and influence of crystallinity on its desolvation; Histidine Ketoisocapron san ensan ethanol wamono kessho no koshitsudo jokenka deno datsu ethanol to datsu ethanol sei ni oyobosu kesshosei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kishimoto, S.; Tanabe, T.; Maruyama, S.; Kishishita, A.; Nagashima, N. [Ajinomoto Co. Inc., Tokyo (Japan)

1996-07-10

Desolvation of L-histidine and a-ketoisocaproic acid complex from ethanolate crystals was investigated. The ethanolate crystals were obtained from ethanol aqueous solutions of above 60 wt% of ethanol. It was difficult to remove ethanol molecules from the crystals lay vacuum drying. However, it was found that ethanol molecules in the crystal lattice could be released under humidified conditions, for example, 313 K and 60% relative humidity, accompanied by transformation to non-solvated crystals. When the peak of 2{theta}=9.0{degree}(CuK{alpha} radiation) in powder X-ray diffraction pattern of the ethanolate crystals was weak, ethanol molecules (about 1wt.%) remained in the crystals at the end of transformations and then the residual ethanol decreased slowly. A controlled moderate cooling process, where the supersaturation is released slowly, is the key point to obtain ethanolate crystals having high `crystallinity` (defined as peak height of 2{theta}=9.0{degree}) which shows quick desolation rather than adding ethanol for a rapid increase of supersaturation in crystallization. 6 refs., 7 figs.

Fiscal 2000 achievement report on the venture business assisting type regional consortium-Core industry creation type. Development of radiation detector utilizing surface reforming effect of irradiation; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Hoshasen shosha ni yoru hyomen kaishitsu koka wo mochiita hoshasen kenshutsuki no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

It has been clarified that the use of some kinds of semiconductor films, such as a rutile type titanium oxide film or a zirconium oxide film, results in a stable photocatalytic reaction in an intensive radioactivity region. In this effort, the effect is applied for the development of a FET (field effect transistor) type radiation detector capable of stable operation under high dose irradiation circumstances. Semiconductor materials such as a rutile type titanium oxide were subjected to irradiation tests on the ground, in which changes in their physical properties such as wettability or conductance were examined and the mechanism of surface reforming under irradiation was elucidated, and proper materials were selected. A prototype high radiation detector was fabricated that covers a 1mGy/hr-4kGy/hr region. For the establishment of a technology for growing spherical semiconductor crystals under microgravity, basic experiments were conducted using a free-fall facility at the Japan Microgravity Center. Basic experiments were conducted for the fabrication of a prototype radiation detector to operate in a high radiation region from 0.1kGy/hr to 2kGy/hr and beyond, and a prototype spherical semiconductor radiation detector was fabricated. Achievements of the effort are mentioned above. (NEDO)

Fiscal 1997 report on the results on the international standardization R and D. Development of chemical methods to analyze/evaluate metallic coatings of surface treated steel coating sheets; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Hyomen shori koban mekkiso no kagaku bunseki hyoka hoho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper studied the international standardization of the chemical analysis method and glow discharge optical emission spectrometry. Chemical composition and coating thickness (g/m{sup 2}) of 14 kinds of specimens including alloy coatings and organic coating with zinc and aluminum as base were analyzed by the above-mentioned methods to examine the relation between the both. As the chemical analysis method, used was inductively coupled plasma atomic emission spectrometry. To study the relation between the methods, it was found to be necessary to recognize morphology at the boundary between the coating and base steel using, for example, scanning electron microscope (SEM) and electro-probe micro-analysis (EPMA). To measure traceability of the analysis method, with the chemical analysis method as a judgement method, it is necessary to make reference materials by coating materials, to use the calibration graph confirmed by the materials and to adopt the glow discharge optical emission spectrometry. On the basis of such way of thinking, drafts were worked out for the international standardization of the chemical analysis method and glow discharge optical emission spectrometry. 7 refs., 117 figs., 33 tabs.

Acceleration effect of alcohols on ion association of molbdophosphate with malachite green and its use to the sensitive flow-injection determination of phosphate. Molybdo rinsan ion-malachite green ion kaigotai seisei ni oyobosu alcohol no hanno sokushinkoka to sore wo riyosuru rin no kokando flow injection bunseki

Energy Technology Data Exchange (ETDEWEB)

Motomizu, S; Yasuda, Y; Oshima, M [Okayama Univ., Okayama (Japan). Faculty of Science

1991-12-10

Molibdophosphoric acid (PMo) reacts with malachite green (MG{sup +}) to form a colored ion associate (MG{sup +}- PMo) in an acidic solution according to the formula : HMG{sup 2+}+H{sub 3}PMo{sub 12}O{sub 40}{yields}(MG{sup +})H{sub 2}PMo{sub 12}O{sub 40}+2H{sup +}. A protonated form HMG{sup 2+} is yellow (the absorption mximum at 446 nm), whereas the ion associate MG{sup +} is blue green (the absorption maximum at 650 nm). MG{sup +} is found to accelerate the formation of PMo. Water-miscible organic solvents such as methanol,ethanol and propanol also accelerate the formation of PMo as well as the formation of MG sup + - PMo. Some anionic surfactants decelerate the reaction, however, contribute to the suppression of the baseline drift in a flow injection analysis (FIA). By the use of the proposed reaction accelerator and surfactant. a highly sensitive FIA system is established for,orthophosphate up to the range of several ppb. 16 figs.. 11 refs.

Effects of elasticity on the damping characteristics of viscous shearing damper and estimation curve for modal damping in stay cables with this type of dampers. Cable seishin'yo nensei sendangata damper no gensui fuka tokusei ni oyobosu banegosei no eikyo to sono sekkeiyo gensui hyoka kyokusen

Energy Technology Data Exchange (ETDEWEB)

Yoneda, M. (Kawada Industries Inc., Tokyo (Japan)); Shimoda, I. (Oiles Corp., Tokyo (Japan))

1993-12-20

Oil dampers and viscous shearing dampers have been used to control wind-induced cable vibrations of cable-stayed bridges. The damping addition efficiency in the case where only damping force of the viscous shearing damper is considered was discussed in the previous paper. In this paper, more precise estimation is done by also considering the spring elasticity of the damper. Arranging the results of an indoor excitation test on viscous shearing dampers using SA-P viscous body, an experimental equation to express the spring rigidity is derived. The spring elasticity becomes smaller with increasing temperature of viscous body, decreasing frequency, and increasing amplitude. Then, the damping addition effect is measured by installing the viscous shearing damper on the actual bridge cable, and is compared with the theoretical value resulting from the complex-eigenvalue analysis. Consequently, it is shown that the theoretical value is almost correspondent with the measured result through the analysis using equivalent coefficient of viscosity and equivalent spring constant, which are arranged in the experimental equation. Moreover, application examples of damping estimation curves for designing cables with dampers are given. 15 refs., 13 figs., 10 tabs.

Report on achievements in fiscal 1998. Venture business growing type consortium - small business creating infrastructure (Research on polychloride vinyl resin substituting technology applying technology to reform surface of polymeric materials); 1998 nendo kobunshi zairyo no hyomen kaishitsu gijutsu wo oyoshita pori enka biniru jushi daitaika gijutsu ni kansuru kebnky seika hokokusho.

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project is intended to develop a technology to substitute polyvinyl chloride resin being regarded as the generation source of dioxines and environmental hormones in spite of being low in cost and having many excellent characteristics, with polyolefin resin having the same mechanical properties. It has become possible to improve adhesion of polyolefin, and substitute the products manufactured by using polyvinyl chloride resin currently with the polyolefin resin having about the same mechanical properties by establishing the technology to form two layers of polyolefin resin and modified polyolefin resin having polar groups, and by developing a bonding pretreatment agent using soft polyolefin resin as the base. The developed technology can be applied to developing products as targeted by the business entities participating in this project (the edge material for bath tub lids, a product currently available, and the water draining pipe as a new product). The current fiscal year has executed the following activities: (1) improvement in high-frequency weldability by means of polymer blending, (2) development of primers, (3) development of a two-layer forming technology to laminate resin layers with excellent adhesion on material surface, and (4) development of the plasma treatment technology. (NEDO)

Studies on the air distribution and thermal performance of the air circulation wall. Part 4. Study on the thermal emissivity of the air circulation layer`s surfaces; Gaidannetsu tsuki koho ni okeru tsuki sonai no netsu tsuki tokusei ni kansuru kenkyu. 4. Tsuki sonai hyomen no hosha tokusei ni kansuru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Kamimori, K; Sakai, K; Ishihara, O [Kumamoto University, Kumamoto (Japan)

1996-10-27

The thermal and air distribution characteristics of the air circulation wall in a heat-insulated system were grasped using an experimental model. In this paper, the difference in the heat exchange between the wall and air was confirmed based on the radiation on the circulation layer`s surface. In this system, thin air circulation layers with ventilating holes at the top and bottom are attached to the south and north outer walls of a wooden building. This system is a kind of passive solar house that achieves the insolation screening effect and the temperature rising effect based on solar collection. The heat flow in a circulation layer is eliminated by the natural convection heat transfer on the outer wall. The heat flow passing through insulating materials is the heat transfer by radiation. The heat flow based on the in-layer natural convection is increasingly eliminated by the decrease in temperature on the air circulation layer`s surface. The decrease in room surface temperature using aluminum foil and the reflective heat-insulated effect showed that the heat passing through the wall surface decreases as the convection heat transfer in an air circulation layer increases. 6 refs., 20 figs., 3 tabs.

Properties of P/M forged Al-Si alloys made by premixed powders. 1. Influences of dispersion and sizes of proeutectic Si on wear resistance; Kongoho ni yotte sakuseishita Al-Si kei shoketsu tanzo gokin no tokusei. 1. Taimamosei ni oyobosu shosho Si no bunsan jotai to ryukei no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ishijima, Z.; Ichikawa, J.; Sasaki, s.; Shikata, H. [Hitachi Powdered Metals Co. Ltd., Tokyo (Japan)

1995-10-15

Influences of dispersion and sizes of proeutectic Si on wear resistance of P/M Al-Si alloys using the prealloying method and premixing method have been investigated. As a result, discretely dispersed proeutectic Si showed excellent wear resistance in compassion with uniformly dispersed one. The cause is considered to be the unclosed Si soft phase which has been preferentially worn away, consequently acting on forming oil grooves and burying worn particles. Further more the existence of the optimum size of proeutectic Si on wear resistance was confirmed. In the case of finer particles, only Al-Si alloy (pin) was warned away substantially. On the other handgun the case of larger particles, both the Al-Si alloy (pin) and the mating malarial (steel disc) were excessively warned away. It is assumed therefore that the finer proeutectic Si particles are not effective as hard particles, on the contrary, larger proeutectic Si particles increase the abrasive wear against the mating material, and those buried into the mating material initiate wear of Al-Si alloy at the same time. 2 refs., 10 figs., 1 tab.

Emission behaviors of nitrous oxide from automobiles. 4th Report. Aging effect of three way catalyst on N2O mass emissions; Jidosha kara haishutsusareru asanka chisso (N2O) no haishutsu kyodo ni kansuru kenkyu. 4. Sangen shokubai no rekka ga N2O haishutsuryo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Koike, N; Suzuki, H; Odaka, M [Traffic Safety and Nuisance Research Institute, Tokyo (Japan)

1997-10-01

Several kind of three way catalysts with different metal compositions have been developed for trial and their N2O formation behaviors before and after the durability tests have been observed. Then by comparing the N2O formation behavior between new and durability tested catalysts, N2O increase mechanism with aging has been experimentally analyzed. As results, A catalyst temperature at peak N2O formation will sift to higher side by the aging and enters in the range that is the higher percentage in use during test cycle driving. Then this is the main cause of increase in total N2O emission. 4 refs., 10 figs., 2 tabs.

Research on variable swirl intake port for high-speed multivalve DI diesel engine. Effects of port configuration on flow characteristics and swirl generation capacity; 4 ben kogata kosoku DI diesel engine no kahen swirl kyuki port ni kansuru kenkyu. Kyuki port haichi ga ryudo tokusei to swirl seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Kawashima, J; Ogawa, H; Tsuru, Y [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

In our previous papers, the variable swirl intake port system which can control a wide swirl ratio range (from 4 to 10) was described. This system consisted of two separate intake ports, one of them has a flow control valve for changing the swirl ratio. In this type of variable swirl system, some variations of port combination, port shape, and position can be designed. In this paper, the intake flow characteristics of various port combinations were analyzed on the basis of a steady-state air flow test and 3-dimensional computations. The results indicate that the total performance of the twin ports can be estimated from that of a single port in any kind of port combination. Some difference in flow patterns were found in a variety of port combinations even if each swirl ratio is similar. The selected port combinations in our previous study are good for a wide swirl control range. 11 refs., 9 figs., 1 tab.

Fiscal 1997 survey of overseas coal import base arrangement and promotion. Effects of the expansion of coal trade by IPP on the supply/demand of general coal in Asia; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. IPP ni yoru sekitan boeki no kakudai ga Asia no ippantan jukyu ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In consideration of the coal situation in the Asia/Pacific region, a study was made of effects of the expansion of coal trade by IPP on supply/demand of general coal in Asia. When aggregating increases in demand of general coal for electric power use in ten Asian counties, they will be an increase of 130.75 million tons in 2005 over 1997. Fifty nine percent of it is equivalent to the increase by IPP and exceeds the demand expanded by electric utilities operators. Further, a possibility is predicted of contracts and coal quality being different from until now. However, there will be a lot of cases in which plans of constructing power plants in Asia are not so developed as expected except Japan, Korea and Taiwan, and also the effect of the currency crisis starting in Thailand largely affects. In terms of the coal supply, countries which export general coal are only China and Indonesia. Indonesian coal is expanding its production and export rapidly and remarkably. The environmental control in Asia has been tightening, and the fuel selected by IPP is mainly coal rather than natural gas. 40 refs., 94 figs., 179 tabs.

Report on the survey made under the research contract with NEDO, `The International Work Division/Energy Demand Effect Survey.`. Influence of the economic growth in Asia on the energy demand; 1996 nendo `kokusai suihei bungyo energy juyo eikyo chosa` itaku chosa kekka hokokusho. Asia no keizai hatten ga energy juyo ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report includes surveys on the following: (1) the progress situation of the Asian information society, (2) changes of corporate network, business flow, material flow and money flow in association with the information society, (3) the present situation of the industry-accumulated region in Asia and inter-region network, (4) impacts of the above-mentioned changes on the trade and investment structure in Japan, (5) how to tackle the energy issue in Asia in the future. First, effects of the advance of the information society on energy supply/demand were studied. Next, an analysis was made of effects of the progress of the high-grade information society in Asia on economy, industry and corporate action. The degree of the progress of the information society in Asian countries was made clear from the infrastructure arrangement and the developmental status of application. Contribution of the financial network to the economic growth in Asia and the development were clarified. The organization of corporate networks in Asia where paradigms are converting was made clear to consider industrial clusters in Asia. Last, in the light of the economic relationship between Japan and Asia, a study was made on the future policy of Japan for Asia. 238 refs., 77 figs., 89 tabs.

Effects of sintering and paste-baking conditions on PTCR characteristic of (Ba,Sr)TiO{sub 3} vacuum-sintered compact added with TiO{sub 2}(Ti) powder; TiO{sub 2}(ti) fun tenka (Ba,Sr)TiO{sub 3} shinku shoketsutai no PTCR tokusei ni oyobosu shoketsu oyobi paste yakitsuke joken no eikyo

Energy Technology Data Exchange (ETDEWEB)

Kim, J.; Hayashi, K. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

1999-04-15

The effects of sintering temperature (T{sub s}; 1,573 {approx} 1,748K) and time (t{sub s}; 0.6 {approx} 14.4ks) and paste-baking-temperature or heating temperature (T{sub b} or T{sub h}; 673 {approx} 1,273K; t{sub b} is 0.3ks) on PTCR characteristic were investigated for (Ba, Sr)TiO{sub 3} vacuum-sintered compact added with 3.9mass% TiO{sub 2}(Ti) powder of 12.5mass% TiO{sub 2}. The results obtained were as follows; (1) PTCR characteristic developed at all T{sub s} (t{sub s}=3.6ks, T{sub b}=853K). The electrical resistivity at room temperature ({rho}{sub rt}) showed a minimum value of 1.8 times 10{sup 2}ohmcenter dotcm and the {rho}{sub max}/{rho}{sub rt} showed a maximum value of about 10{sup 6} at 1,723K. (2)For all t{sub s} (T{sub s}=1,623K, T{sub b}=853K), PTCR characteristic developed. The {rho}{sub rt} showed a minimum value of 2.6 times 10{sup 3}ohmcenter dotcm at 7.2ks. (3) At T{sub b} above 823K (T{sub s}=1,623K, t{sub s}=3.6ks), PTCR characteristic developed. The {rho}{sub rt} showed a minimum value of 1.0 times 10{sup 3}ohmcenter dotcm. (4)The {rho}-T curve of (Ba, Sr)TiO{sub 3}+TiO{sub 2}(Ti) vacuum-sintered compact was affected more largely by T{sub s}, t{sub s} and T{sub b} than that of (Ba, Sr)TiO{sub 3} air-sintered compact. This was considered to be mainly due to the porous and fine gained microstructure in the former compact. (author)

Effect of TiO2 addition on reaction between SiC and Ni in SiC-Ni cermet spray coatings. Part 2. ; Development of SiC-based cermet spray coatings. SiC-Ni yosha himakuchu no SiC-Ni kaimen hanno ni oyobosu TiO2 tenka no koka. 2. ; SiC-ki sametto yosha himaku no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, T [Kumano Technical College, Mie (Japan); Oki, S; Goda, S [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1992-09-30

The depression of the reaction between SiC and Ni, by adding TiO2 powder in spraying powder which has caused uniform dispersion in spray coating and reduction of TiO2 by the reaction during spraying, was studied. The mass ratio of the mixed components has been, SiC:Ni:TiO2=3:2:1. The spray coating was examined by electron prove microanalysis as well as X-ray diffractometry, centering mainly to the SiC-metal interface reaction. The formation of Ni-Si compounds have been depressed by the addition of TiO2 to spraying powder and by using plasma gas containing H2. Reason for this has been that the TiC formed in the SiC-Ni interface has depressed the reaction at the SiC-Ni interface. Further, TiO2 is reduced during spraying, and TiC is thought to be formed by the reaction between Ti and SiC or reaction between TiO2 and SiC. 8 refs., 6 figs., 1 tab.

Combustion-driven oscillation in a furnace with multispud-type gas burners. 4th Report. Effects of position of secondary air guide sleeve and openness of secondary air guide vane on combustion oscillation condition; Multispud gata gas turner ni okeru nensho shindo. 4. Nijigen kuki sleeve ichi oyobi nijigen kuki vane kaido no shindo reiki ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Akiyama, I.; Okiura, K.; Baba, A.; Orimoto, M. [Babcock-Hitachi K.K., Tokyo (Japan)

1994-07-25

Effects of the position of a secondary air guide sleeve and the openness of a secondary air guide vane on combustion oscillation conditions were studied experimentally for multispud-type gas burners. Pressure fluctuation in furnaces was analyzed with the previously reported resonance factor which was proposed as an index to represent the degree of combustion oscillation. As a result, the combustion oscillation region was largely affected by both position of a guide sleeve and openness of a guide vane. As the openness having large effect on the ratio of primary and secondary air/tertiary air and the position hardly having effect on the ratio were adjusted skillfully, the burner with no combustion oscillation region was achieved in its normal operation range. In addition, as the effect of preheating combustion air was arranged with a standard flow rate or mass flow flux of air, it was suggested the combustion oscillation region due to preheating can be described with the same manner as that due to no preheating. 5 refs., 8 figs.

Achievement report for fiscal 1998 on research and development of multifunction members structure control technologies. Development of advanced surface treatment technologies for methane-fueled aero engines (1. Microstructure control technologies for ultrahigh temperature members); 1998 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (chokoon buzai mikuro kozo seigyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The carbon fiber reinforced carbon composite materials (C/C composites) strong at ultrahigh temperatures are taken up. So as to improve on its resistance to oxidation, corrosion, and abrasion as well as on its strength at ultrahigh temperatures, an ion engineering-assisted technique is used to reform the C/C composite surface layer and a technology is developed for thin coating formation on the C/C composite surface. Next, technologies are developed for multifunction coating formation on top of the surface, for defect prevention or removal from the C/C composite, and for adhesion enhancement between the C/C composite fibers and the matrix. Technologies are further developed for evaluating hostile environment withstanding capabilities at ultrahigh temperatures. In this fiscal year, in the study of microstructure controlling multilayer coating technologies, development is conducted of technologies of ion engineering-assisted surface control and reform and of technologies of forming multifunctional coatings high in reliability and resistance to corrosion. In the field of microstructure control composition, 3-dimensional carbon fiber reinforced carbon composite materials are manufactured by way of trial and evaluated, and their behavior under rigorous conditions is evaluated. (NEDO)

FY 1993 research and development of the technology for controlling structures of functional composite members. R and D of advanced surface processing for methane-fueled aircraft engine members (Technology for controlling the microscopic structures of superhigh-temperature members); 1993 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). Chokoon buzai micro kozo seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Described herein are the results of the FY1993 research and development project, implemented for development of the technologies for modification of material surfaces and interfaces, with the objectives to develop the optimum members for methane-fueled aircraft engines. For R and D of multi-layered films with controlled microscopic structures, the tests are conducted for forming thin-film layers by, e.g., ion implantation, ion mixing and implantation of large quantities of ions as the surface controlling/modification techniques based on, e.g., ionic techniques. The tests are conducted for, e.g., chemical vapor-phase reaction evaporation and low-pressure plasma spraying as the technologies for forming multi-functional films of, e.g., high reliability and resistance to corrosion. For development of the technologies for controlling/compositing the microscopic structures, the tests are conducted for, e.g., selection of the matrix materials, and prevention/removal of defects by the chemical vapor-phase reaction penetration treatment effected for extended periods. For development of the technologies for evaluation of the characteristics under superhigh-temperature environments, the tests are conducted to investigate the mechanical characteristics of isotropically uniform metallic materials under multi-dimensional stresses and evaluation thereof, and mechanical and thermal characteristics of carbon-fiber-reinforced carbon composites and evaluation thereof. (NEDO)

Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.