Particularities of fully-parallel manipulators in 6-DOFs robots design: a review of critical aspects

Directory of Open Access Journals (Sweden)

Milica Lucian

2017-01-01

Full Text Available A whole range of industrial applications requires the presence of parallel mechanisms with six degrees of freedom (6-DOF which have been developed in the last fifteen years, and one of the reasons why they still are a current topic is that present-day computers are capable of performing real-time motion laws of great complexity associated with these types of parallel mechanisms. The present work underlines particularities of parallel manipulators and their importance in the design of 6-DOF robots. The paper reveals the progress made in the last twenty years in the development of 6-DOF parallel manipulators, which increasingly find a wide scope of applications in different industrial areas such as robotics, manufacture and assisted medicine. It also emphasizes the need to determine singular configurations and the effect of cinematic redundancy which can increase the working space of the manipulators by adding active joints in one or more branches of the manipulator. Throughout the work, there were outlined three types of singularities encountered in the modelling of different types of parallel manipulators, and three types of redundancy. Furthermore, an analysis was made of the dimension of the workspace for a series of parallel manipulators, highlighting a number of factors that influence its size.

Parallel manipulators with two end-effectors : Getting a grip on Jacobian-based stiffness analysis

NARCIS (Netherlands)

Hoevenaars, A.G.L.

2016-01-01

Robots that are developed for applications which require a high stiffness-over-inertia ratio, such as pick-and-place robots, machining robots, or haptic devices, are often based on parallel manipulators. Parallel manipulators connect an end-effector to an inertial base using multiple serial

Optical Pushing: A Tool for Parallelized Biomolecule Manipulation

NARCIS (Netherlands)

Sitters, G.; Laurens, N.; de Rijk, E.J.; Kress, H.; Peterman, E.J.G.; Wuite, G.J.L.

2016-01-01

The ability to measure and manipulate single molecules has greatly advanced the field of biophysics. Yet, the addition of more single-molecule tools that enable one to measure in a parallel fashion is important to diversify the questions that can be addressed. Here we present optical pushing (OP), a

A redundant, 6-DOF parallel manipulator structure with improved workspace and dexterity

International Nuclear Information System (INIS)

Stoughton, R.S.; Salerno, R.; Canfield, S.; Reinholtz, C.

1994-08-01

This paper presents a novel manipulator structure which combines two known parallel manipulator structures--a Stewart Platform (SP), and a double octahedral Variable Geometry Truss (VGT). The combined VGT + SP structure is redundant, using nine actuators to realize six-DOF motion. Combining the two structures allows the translational and orientational workspaces of the two individual structures to sum together to a much larger workspace than is generally achievable with parallel manipulator structures. In addition, the VGT portion of the structure allows the configuration of the Stewart Platform to be changed ''on the fly'' from one with a large workspace to one with high dexterity. A useful application of this structure is at the distal end of a truss-based manipulator, where it can serve as a dexterous wrist while preserving an internal passageway for cabling and/or conveyance systems

Multiobjective Optimum Design of a 3-RRR Spherical Parallel Manipulator with Kinematic and Dynamic Dexterities

DEFF Research Database (Denmark)

Wu, Guanglei

2012-01-01

parameters of the spherical parallel manipulator. The proposed approach is illustrated with the optimum design of a special spherical parallel manipulator with unlimited rolling motion. The corresponding optimization problem aims to maximize the kinematic and dynamic dexterities over its regular shaped...

Chattering-Free Neuro-Sliding Mode Control of 2-DOF Planar Parallel Manipulators

Directory of Open Access Journals (Sweden)

Tien Dung Le

2013-01-01

Full Text Available This paper proposes a novel chattering free neuro-sliding mode controller for the trajectory tracking control of two degrees of freedom (DOF parallel manipulators which have a complicated dynamic model, including modelling uncertainties, frictional uncertainties and external disturbances. A feedforward neural network (NN is combined with an error estimator to completely compensate the large nonlinear uncertainties and external disturbances of the parallel manipulators. The online weight tuning algorithms of the NN and the structure of the error estimator are derived with the strict theoretical stability proof of the Lyapunov theorem. The upper bound of uncertainties and the upper bound of the approximation errors are not required to be known in advance in order to guarantee the stability of the closed-loop system. The example simulation results show the effectiveness of the proposed control strategy for the tracking control of a 2-DOF parallel manipulator. It results in its being chattering-free, very small tracking errors and its robustness against uncertainties and external disturbances.

A Novel Reconfiguration Strategy of a Delta-Type Parallel Manipulator

Directory of Open Access Journals (Sweden)

Albert Lester Balmaceda-Santamaría

2016-02-01

Full Text Available This work introduces a novel reconfiguration strategy for a Delta-type parallel robot. The robot at hand, whose patent is pending, is equipped with an intermediate mechanism that allows for modifying the operational Cartesian workspace. Furthermore, singularities of the robot may be ameliorated owing to the inherent kinematic redundancy introduced by four actuable kinematic joints. The velocity and acceleration analyses of the parallel manipulator are carried out by resorting to reciprocal-screw theory. Finally, the manipulability of the new robot is investigated based on the computation of the condition number associated with the active Jacobian matrix, a well-known procedure. The results obtained show improved performance of the robot introduced when compared with results generated for another Delta-type robot.

Stiffness Analysis and Comparison of 3-PPR Planar Parallel Manipulators with Actuation Compliance

DEFF Research Database (Denmark)

Wu, Guanglei; Bai, Shaoping; Kepler, Jørgen Asbøl

2012-01-01

In this paper, the stiffness of 3-PPR planar parallel manipulator (PPM) is analyzed with the consideration of nonlinear actuation compliance. The characteristics of the stiffness matrix pertaining to the planar parallel manipulators are analyzed and discussed. Graphic representation of the stiffn...... of the stiffness characteristics by means of translational and rotational stiffness mapping is developed. The developed method is illustrated with an unsymmetrical 3-PPR PPM, being compared with its structure-symmetrical counterpart....

Structural Synthesis of 3-DoF Spatial Fully Parallel Manipulators

Directory of Open Access Journals (Sweden)

Alfonso Hernandez

2014-07-01

Full Text Available In this paper, the architectures of three degrees of freedom (3-DoF spatial, fully parallel manipulators (PMs, whose limbs are structurally identical, are obtained systematically. To do this, the methodology followed makes use of the concepts of the displacement group theory of rigid body motion. This theory works with so-called ‘motion generators’. That is, every limb is a kinematic chain that produces a certain type of displacement in the mobile platform or end-effector. The laws of group algebra will determine the actual motion pattern of the end-effector. The structural synthesis is a combinatorial process of different kinematic chains’ topologies employed in order to get all of the 3-DoF motion pattern possibilities in the end-effector of the fully parallel manipulator.

Kinematic analysis of parallel manipulators by algebraic screw theory

CERN Document Server

Gallardo-Alvarado, Jaime

2016-01-01

This book reviews the fundamentals of screw theory concerned with velocity analysis of rigid-bodies, confirmed with detailed and explicit proofs. The author additionally investigates acceleration, jerk, and hyper-jerk analyses of rigid-bodies following the trend of the velocity analysis. With the material provided in this book, readers can extend the theory of screws into the kinematics of optional order of rigid-bodies. Illustrative examples and exercises to reinforce learning are provided. Of particular note, the kinematics of emblematic parallel manipulators, such as the Delta robot as well as the original Gough and Stewart platforms are revisited applying, in addition to the theory of screws, new methods devoted to simplify the corresponding forward-displacement analysis, a challenging task for most parallel manipulators. Stands as the only book devoted to the acceleration, jerk and hyper-jerk (snap) analyses of rigid-body by means of screw theory; Provides new strategies to simplify the forward kinematic...

Singularity kinematics principle and position-singularity analyses of the 6-3 Stewart-Gough parallel manipulators

International Nuclear Information System (INIS)

Cao, Yi; Zhou, Hui; Li, Baokun; Shen, Long

2011-01-01

This paper presents a new principle and method of kinematics to analyze the singularity of Stewart-Gough parallel manipulators and addresses the property identification of the position-singularity loci of the 6-3 Stewart-Gough manipulators for special orientations. Based on the kinematic relationship of a rigid body, a necessary and sufficient condition that three velocities of three non-collinear points in a moving rigid body can determine a screw motion is addressed and some typical singular configurations of the 6-3 Stewart-Gough parallel manipulators are also addressed in detail. With the above-mentioned condition, a symbolic analytical polynomial expression of degree three in the moving platform position parameters, representing the position-singularity locus of the 6-3 Stewart-Gough manipulators for special orientations, is derived: and the property identification of the position-singularity loci of the 6-3 Stewart-Gough manipulator for these special orientations is investigated at length. It is shown that position-singularity loci of the 6-3 Stewart-Gough parallel manipulator for these special orientations will be a plane and a hyperbolic paraboloid, even three intersecting planes

The Integration of the Image Sensor with a 3-DOF Pneumatic Parallel Manipulator

Directory of Open Access Journals (Sweden)

Hao-Ting Lin

2016-07-01

Full Text Available The study aims to integrate the image sensor for a three-axial pneumatic parallel manipulator which can pick and place objects automatically by the feature information of the image processed through the SURF algorithm. The SURF algorithm is adopted for defining and matching the features of a target object and an object database. In order to accurately mark the center of target and strengthen the feature matching results, the random sample and consensus method (RANSAC is utilized. The ASUS Xtion Pro Live depth camera which can directly estimate the 3-D location of the target point is used in this study. A set of coordinate estimation calibrations is developed for enhancing the accuracy of target location estimation. This study also presents hand gesture recognition exploiting skin detection and noise elimination to determine the active finger count for input signals of the parallel manipulator. The end-effector of the parallel manipulator can be manipulated to the desired poses according to the measured finger count. Finally, the proposed methods are successfully to achieve the feature recognition and pick and place of the target object.

Mechatronic Model Based Computed Torque Control of a Parallel Manipulator

Directory of Open Access Journals (Sweden)

Zhiyong Yang

2008-11-01

Full Text Available With high speed and accuracy the parallel manipulators have wide application in the industry, but there still exist many difficulties in the actual control process because of the time-varying and coupling. Unfortunately, the present-day commercial controlles cannot provide satisfying performance for its single axis linear control only. Therefore, aimed at a novel 2-DOF (Degree of Freedom parallel manipulator called Diamond 600, a motor-mechanism coupling dynamic model based control scheme employing the computed torque control algorithm are presented in this paper. First, the integrated dynamic coupling model is deduced, according to equivalent torques between the mechanical structure and the PM (Permanent Magnetism servomotor. Second, computed torque controller is described in detail for the above proposed model. At last, a series of numerical simulations and experiments are carried out to test the effectiveness of the system, and the results verify the favourable tracking ability and robustness.

Mechatronic Model Based Computed Torque Control of a Parallel Manipulator

Directory of Open Access Journals (Sweden)

Zhiyong Yang

2008-03-01

Full Text Available With high speed and accuracy the parallel manipulators have wide application in the industry, but there still exist many difficulties in the actual control process because of the time-varying and coupling. Unfortunately, the present-day commercial controlles cannot provide satisfying performance for its single axis linear control only. Therefore, aimed at a novel 2-DOF (Degree of Freedom parallel manipulator called Diamond 600, a motor-mechanism coupling dynamic model based control scheme employing the computed torque control algorithm are presented in this paper. First, the integrated dynamic coupling model is deduced, according to equivalent torques between the mechanical structure and the PM (Permanent Magnetism servomotor. Second, computed torque controller is described in detail for the above proposed model. At last, a series of numerical simulations and experiments are carried out to test the effectiveness of the system, and the results verify the favourable tracking ability and robustness.

A class of parallel algorithms for computation of the manipulator inertia matrix

Science.gov (United States)

Fijany, Amir; Bejczy, Antal K.

1989-01-01

Parallel and parallel/pipeline algorithms for computation of the manipulator inertia matrix are presented. An algorithm based on composite rigid-body spatial inertia method, which provides better features for parallelization, is used for the computation of the inertia matrix. Two parallel algorithms are developed which achieve the time lower bound in computation. Also described is the mapping of these algorithms with topological variation on a two-dimensional processor array, with nearest-neighbor connection, and with cardinality variation on a linear processor array. An efficient parallel/pipeline algorithm for the linear array was also developed, but at significantly higher efficiency.

Design and Analysis of Cooperative Cable Parallel Manipulators for Multiple Mobile Cranes

Directory of Open Access Journals (Sweden)

Bin Zi

2012-11-01

Full Text Available The design, dynamic modelling, and workspace are presented in this paper concerning cooperative cable parallel manipulators for multiple mobile cranes (CPMMCs. The CPMMCs can handle complex tasks that are more difficult or even impossible for a single mobile crane. Kinematics and dynamics of the CPMMCs are studied on the basis of geometric methodology and d'Alembert's principle, and a mathematical model of the CPMMCs is developed and presented with dynamic simulation. The constant orientation workspace analysis of the CPMMCs is carried out additionally. As an example, a cooperative cable parallel manipulator for triple mobile cranes with 6 Degrees of Freedom is investigated on the basis of the above design objectives.

Decoupled Sliding Mode Control for a Novel 3-DOF Parallel Manipulator with Actuation Redundancy

Directory of Open Access Journals (Sweden)

Niu Xuemei

2015-05-01

Full Text Available This paper presents a decoupled nonsingular terminal sliding mode controller (DNTSMC for a novel 3-DOF parallel manipulator with actuation redundancy. According to kinematic analysis, the inverse dynamic model for a novel 3-DOF redundantly actuated parallel manipulator is formulated in the task space using Lagrangian formalism and decoupled into three entirely independent subsystems under generalized coordinates to significantly reduce system complexity. Based on the dynamic model, a decoupled sliding mode control strategy is proposed for the parallel manipulator; the idea behind this strategy is to design a nonsingular terminal sliding mode controller for each subsystem, which can drive states of three subsystems to the original equilibrium points simultaneously by two intermediate variables. Additionally, a RBF neural network is used to compensate the cross-coupling force and gravity to enhance the control precision. Simulation and experimental results show that the proposed DNTSMC can achieve better control performances compared with the conventional sliding mode controller (SMC and the DNTSMC without compensator.

Design Issues and Application of Cable-Based Parallel Manipulators for Rehabilitation Therapy

Directory of Open Access Journals (Sweden)

E. Ottaviano

2008-01-01

Full Text Available In this study, cable-based manipulators are proposed for application in rehabilitation therapies. Cable-based manipulators show good features that are very useful when the system has to interact with humans. In particular, they can be used to aid motion or as monitoring/training systems in rehabilitation therapies. Modelling and simulation of both active and passive cable-based parallel manipulators are presented for an application to help older people, patients or disabled people in the sit-to-stand transfer and as a monitoring/training system. Experimental results are presented by using built prototypes.

Kinematics of the 3(RPSP-S Fully Spherical Parallel Manipulator by Means of Screw Theory

Directory of Open Access Journals (Sweden)

Jaime Gallardo-Alvarado

2018-06-01

Full Text Available In this work, the kinematics of a spherical parallel manipulator composed of three peripheral limbs equipped with linear actuators and a passive center shaft is approached by means of the theory of screws. The displacement analysis is carried out solving closure equations, which are obtained upon simple linear combinations of the components of two unit vectors describing the orientation of the moving platform. After, the input-output equations of velocity and acceleration of the spherical parallel manipulator are systematically obtained by resorting to reciprocal-screw theory. This strategy avoids the computation of the passive joint velocity and acceleration rates of the robot manipulator. Numerical examples illustrate the efficiency of the proposed method.

Algorithm for Solution of Direct Kinematic Problem of Multi-sectional Manipulator with Parallel Structure

Directory of Open Access Journals (Sweden)

A. L. Lapikov

2014-01-01

Full Text Available The article is aimed at creating techniques to study multi-sectional manipulators with parallel structure. To solve this task the analysis in the field concerned was carried out to reveal both advantages and drawbacks of such executive mechanisms and main problems to be encountered in the course of research. The work shows that it is inefficient to create complete mathematical models of multisectional manipulators, which in the context of solving a direct kinematic problem are to derive a functional dependence of location and orientation of the end effector on all the generalized coordinates of the mechanism. The structure of multisectional manipulators was considered, where the sections are platform manipulators of parallel kinematics with six degrees of freedom. The paper offers an algorithm to define location and orientation of the end effector of the manipulator by means of iterative solution of analytical equation of the moving platform plane for each section. The equation for the unknown plane is derived using three points, which are attachment points of the moving platform joints. To define the values of joint coordinates a system of nine non-linear equations is completed. It is necessary to mention that for completion of the equation system are used the equations with the same type of non-linearity. The physical sense of all nine equations of the system is Euclidean distance between the points of the manipulator. The result of algorithm execution is a matrix of homogenous transformation for each section. The correlations describing transformations between adjoining sections of the manipulator are given. An example of the mechanism consisting of three sections is examined. The comparison of theoretical calculations with results obtained on a 3D-prototype is made. The next step of the work is to conduct research activities both in the field of dynamics of platform parallel kinematics manipulators with six degrees of freedom and in the

Error Modeling and Design Optimization of Parallel Manipulators

DEFF Research Database (Denmark)

Wu, Guanglei

/backlash, manufacturing and assembly errors and joint clearances. From the error prediction model, the distributions of the pose errors due to joint clearances are mapped within its constant-orientation workspace and the correctness of the developed model is validated experimentally. ix Additionally, using the screw......, dynamic modeling etc. Next, the rst-order dierential equation of the kinematic closure equation of planar parallel manipulator is obtained to develop its error model both in Polar and Cartesian coordinate systems. The established error model contains the error sources of actuation error...

Direct kinematics solution architectures for industrial robot manipulators: Bit-serial versus parallel

Science.gov (United States)

Lee, J.; Kim, K.

1991-01-01

A Very Large Scale Integration (VLSI) architecture for robot direct kinematic computation suitable for industrial robot manipulators was investigated. The Denavit-Hartenberg transformations are reviewed to exploit a proper processing element, namely an augmented CORDIC. Specifically, two distinct implementations are elaborated on, such as the bit-serial and parallel. Performance of each scheme is analyzed with respect to the time to compute one location of the end-effector of a 6-links manipulator, and the number of transistors required.

Direct kinematics solution architectures for industrial robot manipulators: Bit-serial versus parallel

Science.gov (United States)

Lee, J.; Kim, K.

A Very Large Scale Integration (VLSI) architecture for robot direct kinematic computation suitable for industrial robot manipulators was investigated. The Denavit-Hartenberg transformations are reviewed to exploit a proper processing element, namely an augmented CORDIC. Specifically, two distinct implementations are elaborated on, such as the bit-serial and parallel. Performance of each scheme is analyzed with respect to the time to compute one location of the end-effector of a 6-links manipulator, and the number of transistors required.

Parallel algorithms and architecture for computation of manipulator forward dynamics

Science.gov (United States)

Fijany, Amir; Bejczy, Antal K.

1989-01-01

Parallel computation of manipulator forward dynamics is investigated. Considering three classes of algorithms for the solution of the problem, that is, the O(n), the O(n exp 2), and the O(n exp 3) algorithms, parallelism in the problem is analyzed. It is shown that the problem belongs to the class of NC and that the time and processors bounds are of O(log2/2n) and O(n exp 4), respectively. However, the fastest stable parallel algorithms achieve the computation time of O(n) and can be derived by parallelization of the O(n exp 3) serial algorithms. Parallel computation of the O(n exp 3) algorithms requires the development of parallel algorithms for a set of fundamentally different problems, that is, the Newton-Euler formulation, the computation of the inertia matrix, decomposition of the symmetric, positive definite matrix, and the solution of triangular systems. Parallel algorithms for this set of problems are developed which can be efficiently implemented on a unique architecture, a triangular array of n(n+2)/2 processors with a simple nearest-neighbor interconnection. This architecture is particularly suitable for VLSI and WSI implementations. The developed parallel algorithm, compared to the best serial O(n) algorithm, achieves an asymptotic speedup of more than two orders-of-magnitude in the computation the forward dynamics.

Error modelling and experimental validation of a planar 3-PPR parallel manipulator with joint clearances

DEFF Research Database (Denmark)

Wu, Guanglei; Bai, Shaoping; Kepler, Jørgen Asbøl

2012-01-01

This paper deals with the error modelling and analysis of a 3-PPR planar parallel manipulator with joint clearances. The kinematics and the Cartesian workspace of the manipulator are analyzed. An error model is established with considerations of both configuration errors and joint clearances. Using...

Parallel algorithms for interactive manipulation of digital terrain models

Science.gov (United States)

Davis, E. W.; Mcallister, D. F.; Nagaraj, V.

1988-01-01

Interactive three-dimensional graphics applications, such as terrain data representation and manipulation, require extensive arithmetic processing. Massively parallel machines are attractive for this application since they offer high computational rates, and grid connected architectures provide a natural mapping for grid based terrain models. Presented here are algorithms for data movement on the massive parallel processor (MPP) in support of pan and zoom functions over large data grids. It is an extension of earlier work that demonstrated real-time performance of graphics functions on grids that were equal in size to the physical dimensions of the MPP. When the dimensions of a data grid exceed the processing array size, data is packed in the array memory. Windows of the total data grid are interactively selected for processing. Movement of packed data is needed to distribute items across the array for efficient parallel processing. Execution time for data movement was found to exceed that for arithmetic aspects of graphics functions. Performance figures are given for routines written in MPP Pascal.

Position Control of a 3-CPU Spherical Parallel Manipulator

Directory of Open Access Journals (Sweden)

Massimo Callegari

2013-01-01

Full Text Available The paper presents the first experimental results on the control of a prototypal robot designed for the orientation of parts or tools. The innovative machine is a spherical parallel manipulator actuated by 3 linear motors; several position control schemes have been tested and compared with the final aim of designing an interaction controller. The relative simplicity of machine kinematics allowed to test algorithms requiring the closed-loop evaluation of both inverse and direct kinematics; the compensation of gravitational terms has been experimented as well.

Massively Parallel Single-Molecule Manipulation Using Centrifugal Force

Science.gov (United States)

Wong, Wesley; Halvorsen, Ken

2011-03-01

Precise manipulation of single molecules has led to remarkable insights in physics, chemistry, biology, and medicine. However, two issues that have impeded the widespread adoption of these techniques are equipment cost and the laborious nature of making measurements one molecule at a time. To meet these challenges, we have developed an approach that enables massively parallel single- molecule force measurements using centrifugal force. This approach is realized in the centrifuge force microscope, an instrument in which objects in an orbiting sample are subjected to a calibration-free, macroscopically uniform force- field while their micro-to-nanoscopic motions are observed. We demonstrate high- throughput single-molecule force spectroscopy with this technique by performing thousands of rupture experiments in parallel, characterizing force-dependent unbinding kinetics of an antibody-antigen pair in minutes rather than days. Currently, we are taking steps to integrate high-resolution detection, fluorescence, temperature control and a greater dynamic range in force. With significant benefits in efficiency, cost, simplicity, and versatility, single-molecule centrifugation has the potential to expand single-molecule experimentation to a wider range of researchers and experimental systems.

Kinematics and design of a class of parallel manipulators

Science.gov (United States)

Hertz, Roger Barry

1998-12-01

This dissertation is concerned with the kinematic analysis and design of a class of three degree-of-freedom, spatial parallel manipulators. The class of manipulators is characterized by two platforms, between which are three legs, each possessing a succession of revolute, spherical, and revolute joints. The class is termed the "revolute-spherical-revolute" class of parallel manipulators. Two members of this class are examined. The first mechanism is a double-octahedral variable-geometry truss, and the second is termed a double tripod. The history the mechanisms is explored---the variable-geometry truss dates back to 1984, while predecessors of the double tripod mechanism date back to 1869. This work centers on the displacement analysis of these three-degree-of-freedom mechanisms. Two types of problem are solved: the forward displacement analysis (forward kinematics) and the inverse displacement analysis (inverse kinematics). The kinematic model of the class of mechanism is general in nature. A classification scheme for the revolute-spherical-revolute class of mechanism is introduced, which uses dominant geometric features to group designs into 8 different sub-classes. The forward kinematics problem is discussed: given a set of independently controllable input variables, solve for the relative position and orientation between the two platforms. For the variable-geometry truss, the controllable input variables are assumed to be the linear (prismatic) joints. For the double tripod, the controllable input variables are the three revolute joints adjacent to the base (proximal) platform. Multiple solutions are presented to the forward kinematics problem, indicating that there are many different positions (assemblies) that the manipulator can assume with equivalent inputs. For the double tripod these solutions can be expressed as a 16th degree polynomial in one unknown, while for the variable-geometry truss there exist two 16th degree polynomials, giving rise to 256

Experimental and Numerical Study on the Semi-Closed Loop Control of a Planar Parallel Robot Manipulator

Directory of Open Access Journals (Sweden)

Yong-Lin Kuo

2014-01-01

Full Text Available This paper implements the model predictive control to fulfill the position control of a 3-DOF 3-RRR planar parallel manipulator. The research work covers experimental and numerical studies. First, an experimental hardware-in-the-loop system to control the manipulator is constructed. The manipulator is driven by three DC motors, and each motor has an encoder to measure the rotating angles of the motors. The entire system is designed as a semiclosed-loop control system. The controller receives the encoder signals as inputs to produce signals driving the motors. Secondly, the motor parameters are obtained by system identification, and the controllers are designed based on these parameters. Finally, the numerical simulations are performed by incorporating the manipulator kinematics and the motor dynamics; the results are compared with those from the experiments. Both results show that they are in good agreement at steady state. There are two main contributions in this paper. One is the application of the model predictive control to the planar parallel manipulator, and the other one is to overcome the effects of the uncertainties of the DC motors and the performance of the position control due to the dynamic behavior of the manipulator.

Kinematics and optimization of 2-DOF parallel manipulator with revolute actuators and a passive leg

International Nuclear Information System (INIS)

Nam, Yun Joo; Park, Myeong Kwan

2006-01-01

In this paper, a 2-DOF planar parallel manipulator with two revolute actuators and one passive constraining leg. The kinematic analysis of the mechanism is analytically performed : the inverse and forward kinematics problems are solved in closed forms, the workspace is derived systematically, and the three kinds of singular configurations are found. The optimal design to determine the geometric parameters and the operating limits of the actuated legs is performed considering the kinematic manipulability and workspace size. These results of the paper show the effectiveness of the presented manipulator

A novel magnetorheological damper based parallel planar manipulator design

International Nuclear Information System (INIS)

Hoyle, A; Arzanpour, S; Shen, Y

2010-01-01

This paper presents a novel parallel planar robot design which is low cost and simple in structure. The design addresses some of the problems, such as concentration of excessive load on the links and joints, due to wrong commanding signals being given by the controller. In this application two of the conventional actuators are replaced by magnetorheological (MR) dampers, and only one actuator is used to generate motion. The design paradigm is based on the concept that a moving object 'intuitively' follows the path with minimum resistance to its motion. This implies that virtual adoptable constraints can be used effectively to define motion trajectories. In fact, motion generation and adaptive constraints are two elements essential to implementing this strategy. In this paper, MR dampers are used to provide adjustable constraints and to guide the platform that is moved by the linear motor. The model of the MR dampers is derived using the Bouc–Wen model. This model is then used for manipulator simulation and controller design. Two controllers are developed for this manipulator: (1) a closed loop on/off one and (2) a proportional–derivative controller. Also, three different trajectories are defined and used for both the simulations and experiments. The results indicate a good agreement between the simulations and experiments. The experimental results also demonstrate the capability of the manipulator for following sophisticated trajectories

Pa2 kinematic bond in translational parallel manipulators

Directory of Open Access Journals (Sweden)

A. Hernández

2018-01-01

Full Text Available The Pa2 pair is composed of two intertwined articulated parallelograms connecting in parallel two links of a kinematic chain. This pair has two translational degrees of freedom leading to a translational plane variable with the position. Currently, the Pa2 pair appears in conceptual designs presented in recent papers. However, its practical application is very limited. One of the reasons for this can be the high number of redundant constraints it has. But, it has to be considered that most of them can be eliminated by replacing wisely the revolute joints by spherical joints. On the other side, the structure of the Pa2 pair contributes to increase the global stiffness of the kinematic chain in which it is mounted. Also, its implementation is a promising alternative to the problematic passive prismatic joints. In this paper, the Pa2 pairs are used in the design of a 3 − P Pa2 parallel manipulator. The potentiality of this design is evaluated and proven after doing the following analyses: direct and inverse kinematics, singularity study, and workspace computation and assessment.

Dynamic Analysis and Vibration Attenuation of Cable-Driven Parallel Manipulators for Large Workspace Applications

Directory of Open Access Journals (Sweden)

Jingli Du

2013-01-01

Full Text Available Cable-driven parallel manipulators are one of the best solutions to achieving large workspace since flexible cables can be easily stored on reels. However, due to the negligible flexural stiffness of cables, long cables will unavoidably vibrate during operation for large workspace applications. In this paper a finite element model for cable-driven parallel manipulators is proposed to mimic small amplitude vibration of cables around their desired position. Output feedback of the cable tension variation at the end of the end-effector is utilized to design the vibration attenuation controller which aims at attenuating the vibration of cables by slightly varying the cable length, thus decreasing its effect on the end-effector. When cable vibration is attenuated, motion controller could be designed for implementing precise large motion to track given trajectories. A numerical example is presented to demonstrate the dynamic model and the control algorithm.

Characteristics of manipulator for industrial robot with three rotational pairs having parallel axes

Science.gov (United States)

Poteyev, M. I.

1986-01-01

The dynamics of a manipulator with three rotatinal kinematic pairs having parallel axes are analyzed, for application in an industrial robot. The system of Lagrange equations of the second kind, describing the motion of such a mechanism in terms of kinetic energy in generalized coordinates, is reduced to equations of motion in terms of Newton's laws. These are useful not only for either determining the moments of force couples which will produce a prescribed motion or, conversely determining the motion which given force couples will produce but also for solving optimization problems under constraints in both cases and for estimating dynamic errors. As a specific example, a manipulator with all three axes of vertical rotation is considered. The performance of this manipulator, namely the parameters of its motion as functions of time, is compared with that of a manipulator having one rotational and two translational kinematic pairs. Computer aided simulation of their motion on the basis of ideal models, with all three links represented by identical homogeneous bars, has yielded velocity time diagrams which indicate that the manipulator with three rotational pairs is 4.5 times faster.

Coupling characteristics of rigid body motion and elastic deformation of a 3-PRR parallel manipulator with flexible links

International Nuclear Information System (INIS)

Zhang Xuping; Mills, James K.; Cleghorn, William L.

2009-01-01

Modeling of multibody dynamics with flexible links is a challenging task, which not only involves the effect of rigid body motion on elastic deformations, but also includes the influence of elastic deformations on rigid body motion. This paper presents coupling characteristics of rigid body motions and elastic motions of a 3-PRR parallel manipulator with three flexible intermediate links. The intermediate links are modeled as Euler-Bernoulli beams with pinned-pinned boundary conditions based on the assumed mode method (AMM). Using Lagrange multipliers, the fully coupled equations of motions of the flexible parallel manipulator are developed by incorporating the rigid body motions with elastic motions. The mutual dependence of elastic deformations and rigid body motions are investigated from the analysis of the derived equations of motion. Open-loop simulation without joint motion controls and closed-loop simulation with joint motion controls are performed to illustrate the effect of elastic motion on rigid body motions and the coupling effect amongst flexible links. These analyses and results provide valuable insight to the design and control of the parallel manipulator with flexible intermediate links

Latest Advances in Robot Kinematics

CERN Document Server

Husty, Manfred

2012-01-01

This book is  of interest to researchers inquiring about modern topics and methods in the kinematics, control and design of robotic manipulators. It considers the full range of robotic systems, including serial, parallel and cable driven manipulators, both planar and spatial. The systems range from being less than fully mobile to kinematically redundant to overconstrained. In addition to recognized areas, this book also presents recent advances in emerging areas such as the design and control of humanoids and humanoid subsystems, and the analysis, modeling and simulation of human body motions, as well as the mobility analysis of protein molecules and the development of machines which incorporate man.

Design and implementation of a novel modal space active force control concept for spatial multi-DOF parallel robotic manipulators actuated by electrical actuators.

Science.gov (United States)

Yang, Chifu; Zhao, Jinsong; Li, Liyi; Agrawal, Sunil K

2018-01-01

Robotic spine brace based on parallel-actuated robotic system is a new device for treatment and sensing of scoliosis, however, the strong dynamic coupling and anisotropy problem of parallel manipulators result in accuracy loss of rehabilitation force control, including big error in direction and value of force. A novel active force control strategy named modal space force control is proposed to solve these problems. Considering the electrical driven system and contact environment, the mathematical model of spatial parallel manipulator is built. The strong dynamic coupling problem in force field is described via experiments as well as the anisotropy problem of work space of parallel manipulators. The effects of dynamic coupling on control design and performances are discussed, and the influences of anisotropy on accuracy are also addressed. With mass/inertia matrix and stiffness matrix of parallel manipulators, a modal matrix can be calculated by using eigenvalue decomposition. Making use of the orthogonality of modal matrix with mass matrix of parallel manipulators, the strong coupled dynamic equations expressed in work space or joint space of parallel manipulator may be transformed into decoupled equations formulated in modal space. According to this property, each force control channel is independent of others in the modal space, thus we proposed modal space force control concept which means the force controller is designed in modal space. A modal space active force control is designed and implemented with only a simple PID controller employed as exampled control method to show the differences, uniqueness, and benefits of modal space force control. Simulation and experimental results show that the proposed modal space force control concept can effectively overcome the effects of the strong dynamic coupling and anisotropy problem in the physical space, and modal space force control is thus a very useful control framework, which is better than the current joint

Optimum design of 6-DOF parallel manipulator with translational/rotational workspaces for haptic device application

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jung Won; Hwang, Yoon Kwon [Gyeongsang National University, Jinju (Korea, Republic of); Ryu, Je Ha [Gwangju Institute of Science and Technology, Gwangju (Korea, Republic of)

2010-05-15

This paper proposes an optimum design method that satisfies the desired orientation workspace at the boundary of the translation workspace while maximizing the mechanism isotropy for parallel manipulators. A simple genetic algorithm is used to obtain the optimal linkage parameters of a six-degree-of-freedom parallel manipulator that can be used as a haptic device. The objective function is composed of a desired spherical shape translation workspace and a desired orientation workspace located on the boundaries of the desired translation workspace, along with a global conditioning index based on a homogeneous Jacobian matrix. The objective function was optimized to satisfy the desired orientation workspace at the boundary positions as translated from a neutral position of the increased entropy mechanism. An optimization result with desired translation and orientation workspaces for a haptic device was obtained to show the effectiveness of the suggested scheme, and the kinematic performances of the proposed model were compared with those of a preexisting base model

Optimum design of 6-DOF parallel manipulator with translational/rotational workspaces for haptic device application

International Nuclear Information System (INIS)

Yoon, Jung Won; Hwang, Yoon Kwon; Ryu, Je Ha

2010-01-01

This paper proposes an optimum design method that satisfies the desired orientation workspace at the boundary of the translation workspace while maximizing the mechanism isotropy for parallel manipulators. A simple genetic algorithm is used to obtain the optimal linkage parameters of a six-degree-of-freedom parallel manipulator that can be used as a haptic device. The objective function is composed of a desired spherical shape translation workspace and a desired orientation workspace located on the boundaries of the desired translation workspace, along with a global conditioning index based on a homogeneous Jacobian matrix. The objective function was optimized to satisfy the desired orientation workspace at the boundary positions as translated from a neutral position of the increased entropy mechanism. An optimization result with desired translation and orientation workspaces for a haptic device was obtained to show the effectiveness of the suggested scheme, and the kinematic performances of the proposed model were compared with those of a preexisting base model

A fine adjustment mechanism of the second crystal in a double-crystal monochromator with a 3-PS parallel manipulator

International Nuclear Information System (INIS)

Cao Chongzhen; Gao, X.; Ma, P.; Yu, H.; Wang, F.; Huang, Y.; Liu, P.

2005-01-01

A novel fine adjustment mechanism of the second crystal in a double-crystal monochromator is put forward, which is based on a 3-PS parallel manipulator and the magnetic force. Not only is the principle of fine adjusting the pitch angle and the roll angle analyzed, but also optimization of the structure parameters of the permanent magnet, a key part of the fine adjustment mechanism. The fine adjustment mechanism with the 3-PS parallel manipulator has been applied successfully in the double-crystal monochromator of 4W1B beam line in the Beijing Synchrotron Radiation Facility (BSRF)

Dimensional synthesis of a 3-DOF parallel manipulator with full circle rotation

Science.gov (United States)

Ni, Yanbing; Wu, Nan; Zhong, Xueyong; Zhang, Biao

2015-07-01

Parallel robots are widely used in the academic and industrial fields. In spite of the numerous achievements in the design and dimensional synthesis of the low-mobility parallel robots, few research efforts are directed towards the asymmetric 3-DOF parallel robots whose end-effector can realize 2 translational and 1 rotational(2T1R) motion. In order to develop a manipulator with the capability of full circle rotation to enlarge the workspace, a new 2T1R parallel mechanism is proposed. The modeling approach and kinematic analysis of this proposed mechanism are investigated. Using the method of vector analysis, the inverse kinematic equations are established. This is followed by a vigorous proof that this mechanism attains an annular workspace through its circular rotation and 2 dimensional translations. Taking the first order perturbation of the kinematic equations, the error Jacobian matrix which represents the mapping relationship between the error sources of geometric parameters and the end-effector position errors is derived. With consideration of the constraint conditions of pressure angles and feasible workspace, the dimensional synthesis is conducted with a goal to minimize the global comprehensive performance index. The dimension parameters making the mechanism to have optimal error mapping and kinematic performance are obtained through the optimization algorithm. All these research achievements lay the foundation for the prototype building of such kind of parallel robots.

Parallel control method for a bilateral master-slave manipulator

International Nuclear Information System (INIS)

Miyazaki, Tomohiro; Hagihara, Shiro

1989-01-01

In this paper, a new control method for a bilateral master-slave manipulator is proposed. The proposed method yields stable and fast response of the control system. These are essential to obtain a precise position control and a sensitive force reflection control. In the conventional position-force control method, each control loop of the master and the slave arms are connected in series to construct a bilateral control loop. Therefore the total phase lag through the bilateral control loop becomes twice as much as that of one arm control. Such phase lag makes the control system unstable and control performance worse. To improve the stability and the control performance, we propose 'parallel control method.' In the proposed method, the control loops of the master and the slave arms are connected in parallel so that the total phase lag is reduced to as much as that of one arm. The stability condition of the proposed method is studied and it is proved that the stability of this method can be guaranteed independent of the rigidness of a reaction surface and the position/force ratio between the master and the slave arms while the stability of the conventional method depends on them. (author)

A simple approach to solving the kinematics of the 4-UPS/PS (3R1T) parallel manipulator

Energy Technology Data Exchange (ETDEWEB)

Gallardo-Alvarado, Jaime; Gracio-Murillo, Mario A. [Instituto Tecnologico de Celaya, Celaya (Mexico); Islam, Md. Nazrul [Universiti Malasya Sabah, Sabah (Malaysia); Abedinnasab, Mohammad H. [Rowan University, New Jersey (United States)

2016-05-15

This work reports on the position, velocity and acceleration analyses of a four-degrees-of-freedom parallel manipulator, 4-DoF-PM for brevity, which generates Three-rotation-one-translation (3R1T) motion. Nearly closed-form solutions to solve the forward displacement analysis are easily obtained based on closure equations formulated upon linear combinations of the coordinates of three non-collinear points embedded in the moving platform. Then, the input-output equations of velocity and acceleration of the robot manipulator are systematically established by resorting to the theory of screws. To this end, the Klein form of the Lie algebra se(3) of the Euclidean group SE(3) is systematically applied to the velocity and reduced acceleration state in screw form of the moving platform cancelling the passive joint rates of the parallel manipulator. Numerical examples, which are confirmed by means of commercially available software, are provided to show the application of the method.

A simple approach to solving the kinematics of the 4-UPS/PS (3R1T) parallel manipulator

International Nuclear Information System (INIS)

Gallardo-Alvarado, Jaime; Gracio-Murillo, Mario A.; Islam, Md. Nazrul; Abedinnasab, Mohammad H.

2016-01-01

This work reports on the position, velocity and acceleration analyses of a four-degrees-of-freedom parallel manipulator, 4-DoF-PM for brevity, which generates Three-rotation-one-translation (3R1T) motion. Nearly closed-form solutions to solve the forward displacement analysis are easily obtained based on closure equations formulated upon linear combinations of the coordinates of three non-collinear points embedded in the moving platform. Then, the input-output equations of velocity and acceleration of the robot manipulator are systematically established by resorting to the theory of screws. To this end, the Klein form of the Lie algebra se(3) of the Euclidean group SE(3) is systematically applied to the velocity and reduced acceleration state in screw form of the moving platform cancelling the passive joint rates of the parallel manipulator. Numerical examples, which are confirmed by means of commercially available software, are provided to show the application of the method.

Forward kinematics solutions of a special six-degree-of-freedom parallel manipulator with three limbs

Directory of Open Access Journals (Sweden)

Jianxun Fu

2015-05-01

Full Text Available This article presents a special 6-degree-of freedom parallel manipulator, and the mechanical structure of this robot has been introduced; with this structure, the kinematic constrain equations are decoupled. Based on this character, the polynomial solutions of the forward kinematics problem are also presented. In this method, the closed-loop kinematic chain of the manipulator is divided into two parts, the solution forward position kinematics is obtained by a first-degree polynomial equation first, and then an eighth-degree polynomial equation in a single variable for the forward orientation kinematics is obtained. Based on those solutions, the configurations of the robot, including position and orientation of the end-effector, are graphically displayed. A numerical simulation is given to verify the algorithm, and the result implies that for a given set of input values, the manipulator can be assembled in eight different configurations at most. And a set of experiments illustrate the motion ability for forward kinematics of the prototype of this manipulator.

Synchronized motion control and precision positioning compensation of a 3-DOFs macro-micro parallel manipulator fully actuated by piezoelectric actuators

Science.gov (United States)

Zhang, Quan; Li, Chaodong; Zhang, Jiantao; Zhang, Xu

2017-11-01

The macro-micro combined approach, as an effective way to realize trans-scale nano-precision positioning with multi-dimensions and high velocity, plays a significant role in integrated circuit manufacturing field. A 3-degree-of-freedoms (3-DOFs) macro-micro manipulator is designed and analyzed to compromise the conflictions among the large stroke, high precision and multi-DOFs. The macro manipulator is a 3-Prismatic-Revolute-Revolute (3-PRR) structure parallel manipulator which is driven by three linear ultrasonic motors. The dynamic model and the cross-coupling error based synchronized motion controller of the 3-PRR parallel manipulator are theoretical analyzed and experimental tested. To further improve the positioning accuracy, a 3-DOFs monolithic compliant manipulator actuated by three piezoelectric stack actuators is designed. Then a multilayer BP neural network based inverse kinematic model identifier is developed to perform the positioning control. Finally, by forming the macro-micro structure, the dual stage manipulator successfully achieved the positioning task from the point (2 mm, 2 mm, 0 rad) back to the original point (0 mm, 0 mm, 0 rad) with the translation errors in X and Y directions less than ±50 nm and the rotation error around Z axis less than ±1 μrad, respectively.

In-Bore Prostate Transperineal Interventions with an MRI-guided Parallel Manipulator: System Development and Preliminary Evaluation

Science.gov (United States)

Eslami, Sohrab; Shang, Weijian; Li, Gang; Patel, Nirav; Fischer, Gregory S.; Tokuda, Junichi; Hata, Nobuhiko; Tempany, Clare M.; Iordachita, Iulian

2015-01-01

Background The robot-assisted minimally-invasive surgery is well recognized as a feasible solution for diagnosis and treatment of the prostate cancer in human. Methods In this paper the kinematics of a parallel 4 Degrees-of-Freedom (DOF) surgical manipulator designed for minimally invasive in-bore prostate percutaneous interventions through the patient's perineum. The proposed manipulator takes advantage of 4 sliders actuated by MRI-compatible piezoelectric motors and incremental rotary encoders. Errors, mostly originating from the design and manufacturing process, need to be identified and reduced before the robot is deployed in the clinical trials. Results The manipulator has undergone several experiments to evaluate the repeatability and accuracy of the needle placement which is an essential concern in percutaneous prostate interventions. Conclusion The acquired results endorse the sustainability, precision (about 1 mm in air (in x or y direction) at the needle's reference point) and reliability of the manipulator. PMID:26111458

MEMS 6 degrees of freedom parallel micro manipulator for TEM sample manipulation

NARCIS (Netherlands)

Brouwer, Dannis Michel; de Jong, B.R.; Soemers, Herman

2005-01-01

Up till now MEMS actuators acted either only in-plane or only out-of plane restricting to 3 DOF manipulation. A design for a millimeter-sized manipulator with 6 degrees of freedom to manipulate a micron-sized substrate at nanometer resolution over strokes of 10 microns with a position stability

Parallel and patterned optogenetic manipulation of neurons in the brain slice using a DMD-based projector.

Science.gov (United States)

Sakai, Seiichiro; Ueno, Kenichi; Ishizuka, Toru; Yawo, Hiromu

2013-01-01

Optical manipulation technologies greatly advanced the understanding of the neuronal network and its dysfunctions. To achieve patterned and parallel optical switching, we developed a microscopic illumination system using a commercial DMD-based projector and a software program. The spatiotemporal patterning of the system was evaluated using acute slices of the hippocampus. The neural activity was optically manipulated, positively by the combination of channelrhodopsin-2 (ChR2) and blue light, and negatively by the combination of archaerhodopsin-T (ArchT) and green light. It is suggested that our projector-managing optical system (PMOS) would effectively facilitate the optogenetic analyses of neurons and their circuits. Copyright © 2012 Elsevier Ireland Ltd and the Japan Neuroscience Society. All rights reserved.

A Comparison Study on Motion/Force Transmissibility of Two Typical 3-DOF Parallel Manipulators: The Sprint Z3 and A3 Tool Heads

Directory of Open Access Journals (Sweden)

Xiang Chen

2014-01-01

Full Text Available This paper presents a comparison study of two important three-degree-of-freedom (DOF parallel manipulators, the Sprint Z3 head and the A3 head, both commonly used in industry. As an initial step, the inverse kinematics are derived and an analysis of two classes of limbs is carried out via screw theory. For comparison, three transmission indices are then defined to describe their motion/force transmission performance. Based on the same main parameters, the compared results reveal some distinct characteristics in addition to the similarities between the two parallel manipulators. To a certain extent, the A3 head outperforms the common Sprint Z3 head, providing a new and satisfactory option for a machine tool head in industry.

Modelling, Simulation and Testing of a Reconfigurable Cable-Based Parallel Manipulator as Motion Aiding System

Directory of Open Access Journals (Sweden)

Gianni Castelli

2010-01-01

Full Text Available This paper presents results on the modelling, simulation and experimental tests of a cable-based parallel manipulator to be used as an aiding or guiding system for people with motion disabilities. There is a high level of motivation for people with a motion disability or the elderly to perform basic daily-living activities independently. Therefore, it is of great interest to design and implement safe and reliable motion assisting and guiding devices that are able to help end-users. In general, a robot for a medical application should be able to interact with a patient in safety conditions, i.e. it must not damage people or surroundings; it must be designed to guarantee high accuracy and low acceleration during the operation. Furthermore, it should not be too bulky and it should exert limited wrenches after close interaction with people. It can be advisable to have a portable system which can be easily brought into and assembled in a hospital or a domestic environment. Cable-based robotic structures can fulfil those requirements because of their main characteristics that make them light and intrinsically safe. In this paper, a reconfigurable four-cable-based parallel manipulator has been proposed as a motion assisting and guiding device to help people to accomplish a number of tasks, such as an aiding or guiding system to move the upper and lower limbs or the whole body. Modelling and simulation are presented in the ADAMS environment. Moreover, experimental tests are reported as based on an available laboratory prototype.

Adaptive robust trajectory tracking control of a parallel manipulator driven by pneumatic cylinders

Directory of Open Access Journals (Sweden)

Ce Shang

2016-04-01

Full Text Available Due to the compressibility of air, non-linear characteristics, and parameter uncertainties of pneumatic elements, the position control of a pneumatic cylinder or parallel platform is still very difficult while comparing with the systems driven by electric or hydraulic power. In this article, based on the basic dynamic model and descriptions of thermal processes, a controller integrated with online parameter estimation is proposed to improve the performance of a pneumatic cylinder controlled by a proportional valve. The trajectory tracking error is significantly decreased by applying this method. Moreover, the algorithm is expanded to the problem of posture trajectory tracking for the three-revolute prismatic spherical pneumatic parallel manipulator. Lyapunov’s method is used to give the proof of stability of the controller. Using NI-CompactRio, NI-PXI, and Veristand platform as the realistic controller hardware and data interactive environment, the adaptive robust control algorithm is applied to the physical system successfully. Experimental results and data analysis showed that the posture error of the platform could be about 0.5%–0.7% of the desired trajectory amplitude. By integrating this method to the mechatronic system, the pneumatic servo solutions can be much more competitive in the industrial market of position and posture control.

Structure Assembly by a Heterogeneous Team of Robots Using State Estimation, Generalized Joints, and Mobile Parallel Manipulators

Science.gov (United States)

Komendera, Erik E.; Adhikari, Shaurav; Glassner, Samantha; Kishen, Ashwin; Quartaro, Amy

2017-01-01

Autonomous robotic assembly by mobile field robots has seen significant advances in recent decades, yet practicality remains elusive. Identified challenges include better use of state estimation to and reasoning with uncertainty, spreading out tasks to specialized robots, and implementing representative joining methods. This paper proposes replacing 1) self-correcting mechanical linkages with generalized joints for improved applicability, 2) assembly serial manipulators with parallel manipulators for higher precision and stability, and 3) all-in-one robots with a heterogeneous team of specialized robots for agent simplicity. This paper then describes a general assembly algorithm utilizing state estimation. Finally, these concepts are tested in the context of solar array assembly, requiring a team of robots to assemble, bond, and deploy a set of solar panel mockups to a backbone truss to an accuracy not built into the parts. This paper presents the results of these tests.

Rapid optimization of tension distribution for cable-driven parallel manipulators with redundant cables

Science.gov (United States)

Ouyang, Bo; Shang, Weiwei

2016-03-01

The solution of tension distributions is infinite for cable-driven parallel manipulators(CDPMs) with redundant cables. A rapid optimization method for determining the optimal tension distribution is presented. The new optimization method is primarily based on the geometry properties of a polyhedron and convex analysis. The computational efficiency of the optimization method is improved by the designed projection algorithm, and a fast algorithm is proposed to determine which two of the lines are intersected at the optimal point. Moreover, a method for avoiding the operating point on the lower tension limit is developed. Simulation experiments are implemented on a six degree-of-freedom(6-DOF) CDPM with eight cables, and the results indicate that the new method is one order of magnitude faster than the standard simplex method. The optimal distribution of tension distribution is thus rapidly established on real-time by the proposed method.

Microradiographic microsphere manipulator

International Nuclear Information System (INIS)

Singleton, R.M.

1980-01-01

A method and apparatus are provided for radiographic characterization of small hollow spherical members (microspheres), constructed of either optically transparent or opaque materials. The apparatus involves a microsphere manipulator which holds a batch of microspheres between two parallel thin plastic films for contact microradiographic characterization or projection microradiography thereof. One plastic film is translated to relative to and parallel to the other to roll the microspheres through any desired angle to allow different views of the microspheres

Multi-Objective Design Optimization of an Over-Constrained Flexure-Based Amplifier

Directory of Open Access Journals (Sweden)

Yuan Ni

2015-07-01

Full Text Available The optimizing design for enhancement of the micro performance of manipulator based on analytical models is investigated in this paper. By utilizing the established uncanonical linear homogeneous equations, the quasi-static analytical model of the micro-manipulator is built, and the theoretical calculation results are tested by FEA simulations. To provide a theoretical basis for a micro-manipulator being used in high-precision engineering applications, this paper investigates the modal property based on the analytical model. Based on the finite element method, with multipoint constraint equations, the model is built and the results have a good match with the simulation. The following parametric influences studied show that the influences of other objectives on one objective are complicated.  Consequently, the multi-objective optimization by the derived analytical models is carried out to find out the optimal solutions of the manipulator. Besides the inner relationships among these design objectives during the optimization process are discussed.

Design of a planar 3-DOF parallel micromanipulator

International Nuclear Information System (INIS)

Lee, Jeong Jae; Dong, Yanlu; Jeon, Yong Ho; Lee, Moon Gu

2013-01-01

A planar three degree-of-freedom (DOF) parallel manipulator is proposed to be applied for alignment during assembly of microcomponents. It adopts a PRR (prismatic-revolute-revolute) mechanism to meet the requirements of high precision for assembly and robustness against disturbance. The mechanism was designed to have a large workspace and good dexterity because parallel mechanisms usually have a narrow range and singularity of motion compared to serial mechanisms. Inverse kinematics and a simple closed-loop algorithm of the parallel manipulator are presented to control it. Experimental tests have been carried out with high-resolution capacitance sensors to verify the performance of the mechanism. The results of experiments show that the manipulator has a large workspace of ±1.0 mm, ±1.0 mm, and ±10 mrad in the X-, Y-, and θ-directions, respectively. This is a large workspace when considering it adopts a parallel mechanism and has a small size, 100 ´ 100 ´ 100 mm3 . It also has a good precision of 2 μm, 3 μm, and 0.2 mrad, in the X-, Y-, and θ- axes, respectively. These are high resolutions considering the manipulator adopts conventional joints. The manipulator is expected to have good dexterity.

Design Sliding Mode Controller of with Parallel Fuzzy Inference System Compensator to Control of Robot Manipulator

Directory of Open Access Journals (Sweden)

Farzin Piltan

2013-06-01

Full Text Available Sliding mode controller (SMC is a significant nonlinear controller under condition of partly uncertain dynamic parameters of system. This controller is used to control of highly nonlinear systems especially for robot manipulators, because this controller is a robust and stable. Conversely, pure sliding mode controller is used in many applications; it has two important drawbacks namely; chattering phenomenon, and nonlinear equivalent dynamic formulation in uncertain dynamic parameter. The nonlinear equivalent dynamic formulation problem and chattering phenomenon in uncertain system can be solved by using artificial intelligence theorem. However fuzzy logic controller is used to control complicated nonlinear dynamic systems, but it cannot guarantee stability and robustness.  In this research parallel fuzzy logic theory is used to compensate the system dynamic uncertainty.

Robust nonlinear PID-like fuzzy logic control of a planar parallel (2PRP-PPR) manipulator.

Science.gov (United States)

Londhe, P S; Singh, Yogesh; Santhakumar, M; Patre, B M; Waghmare, L M

2016-07-01

In this paper, a robust nonlinear proportional-integral-derivative (PID)-like fuzzy control scheme is presented and applied to complex trajectory tracking control of a 2PRP-PPR (P-prismatic, R-revolute) planar parallel manipulator (motion platform) with three degrees-of-freedom (DOF) in the presence of parameter uncertainties and external disturbances. The proposed control law consists of mainly two parts: first part uses a feed forward term to enhance the control activity and estimated perturbed term to compensate for the unknown effects namely external disturbances and unmodeled dynamics, and the second part uses a PID-like fuzzy logic control as a feedback portion to enhance the overall closed-loop stability of the system. Experimental results are presented to show the effectiveness of the proposed control scheme. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Position Analysis of a Hybrid Serial-Parallel Manipulator in Immersion Lithography

Directory of Open Access Journals (Sweden)

Jie-jie Shao

2015-01-01

Full Text Available This paper proposes a novel hybrid serial-parallel mechanism with 6 degrees of freedom. The new mechanism combines two different parallel modules in a serial form. 3-P̲(PH parallel module is architecture of 3 degrees of freedom based on higher joints and specializes in describing two planes’ relative pose. 3-P̲SP parallel module is typical architecture which has been widely investigated in recent researches. In this paper, the direct-inverse position problems of the 3-P̲SP parallel module in the couple mixed-type mode are analyzed in detail, and the solutions are obtained in an analytical form. Furthermore, the solutions for the direct and inverse position problems of the novel hybrid serial-parallel mechanism are also derived and obtained in the analytical form. The proposed hybrid serial-parallel mechanism is applied to regulate the immersion hood’s pose in an immersion lithography system. Through measuring and regulating the pose of the immersion hood with respect to the wafer surface simultaneously, the immersion hood can track the wafer surface’s pose in real-time and the gap status is stabilized. This is another exploration to hybrid serial-parallel mechanism’s application.

LiNbO3: A photovoltaic substrate for massive parallel manipulation and patterning of nano-objects

International Nuclear Information System (INIS)

Carrascosa, M.; García-Cabañes, A.; Jubera, M.; Ramiro, J. B.; Agulló-López, F.

2015-01-01

The application of evanescent photovoltaic (PV) fields, generated by visible illumination of Fe:LiNbO 3 substrates, for parallel massive trapping and manipulation of micro- and nano-objects is critically reviewed. The technique has been often referred to as photovoltaic or photorefractive tweezers. The main advantage of the new method is that the involved electrophoretic and/or dielectrophoretic forces do not require any electrodes and large scale manipulation of nano-objects can be easily achieved using the patterning capabilities of light. The paper describes the experimental techniques for particle trapping and the main reported experimental results obtained with a variety of micro- and nano-particles (dielectric and conductive) and different illumination configurations (single beam, holographic geometry, and spatial light modulator projection). The report also pays attention to the physical basis of the method, namely, the coupling of the evanescent photorefractive fields to the dielectric response of the nano-particles. The role of a number of physical parameters such as the contrast and spatial periodicities of the illumination pattern or the particle deposition method is discussed. Moreover, the main properties of the obtained particle patterns in relation to potential applications are summarized, and first demonstrations reviewed. Finally, the PV method is discussed in comparison to other patterning strategies, such as those based on the pyroelectric response and the electric fields associated to domain poling of ferroelectric materials

Dionis: A Novel Remote-Center-of-Motion Parallel Manipulator for Minimally Invasive Surgery

Directory of Open Access Journals (Sweden)

R. Beira

2011-01-01

Full Text Available The large volume and reduced dexterity of current surgical robotic systems are factors that restrict their effective performance. To improve the usefulness of surgical robots in minimally invasive surgery (MIS, a compact and accurate positioning mechanism, named Dionis, is proposed in this paper. This spatial hybrid mechanism based on a novel parallel kinematics is able to provide three rotations and one translation for single port procedures. The corresponding axes intersect at a remote center of rotation (RCM that is the MIS entry port. Another important feature of the proposed positioning manipulator is that it can be placed below the operating table plane, allowing a quick and direct access to the patient, without removing the robotic system. This, besides saving precious space in the operating room, may improve safety over existing solutions. The conceptual design of Dionis is presented in this paper. Solutions for the inverse and direct kinematics are developed, as well as the analytical workspace and singularity analysis. Due to its unique design and kinematics, the proposed mechanism is highly compact, stiff and its dexterity fullfils the workspace specifications for MIS procedures.

Kinematic sensitivity of robot manipulators

Science.gov (United States)

Vuskovic, Marko I.

1989-01-01

Kinematic sensitivity vectors and matrices for open-loop, n degrees-of-freedom manipulators are derived. First-order sensitivity vectors are defined as partial derivatives of the manipulator's position and orientation with respect to its geometrical parameters. The four-parameter kinematic model is considered, as well as the five-parameter model in case of nominally parallel joint axes. Sensitivity vectors are expressed in terms of coordinate axes of manipulator frames. Second-order sensitivity vectors, the partial derivatives of first-order sensitivity vectors, are also considered. It is shown that second-order sensitivity vectors can be expressed as vector products of the first-order sensitivity vectors.

A general approach for optimal kinematic design of 6-DOF parallel ...

Indian Academy of Sciences (India)

Optimal kinematic design of parallel manipulators is a challenging problem. In this work, an attempt has been made to present a generalized approach of kinematic design for a 6-legged parallel manipulator, by considering only the minimally required design parameters. The same approach has been used to design a ...

Optimal design of a spherical parallel manipulator based on kinetostatic performance using evolutionary techniques

Energy Technology Data Exchange (ETDEWEB)

Daneshmand, Morteza [University of Tartu, Tartu (Estonia); Saadatzi, Mohammad Hossein [Colorado School of Mines, Golden (United States); Kaloorazi, Mohammad Hadi [École de Technologie Supérieur, Montréal (Canada); Masouleh, Mehdi Tale [University of Tehran, Tehran (Iran, Islamic Republic of); Anbarjafari, Gholamreza [Hasan Kalyoncu University, Gaziantep (Turkmenistan)

2016-03-15

This study aims to provide an optimal design for a Spherical parallel manipulator (SPM), namely, the Agile Eye. This aim is approached by investigating kinetostatic performance and workspace and searching for the most promising design. Previously recommended designs are examined to determine whether they provide acceptable kinetostatic performance and workspace. Optimal designs are provided according to different kinetostatic performance indices, especially kinematic sensitivity. The optimization process is launched based on the concept of the genetic algorithm. A single-objective process is implemented in accordance with the guidelines of an evolutionary algorithm called differential evolution. A multi-objective procedure is then provided following the reasoning of the nondominated sorting genetic algorithm-II. This process results in several sets of Pareto points for reconciliation between kinetostatic performance indices and workspace. The concept of numerous kinetostatic performance indices and the results of optimization algorithms are elaborated. The conclusions provide hints on the provided set of designs and their credibility to provide a well-conditioned workspace and acceptable kinetostatic performance for the SPM under study, which can be well extended to other types of SPMs.

Design of mechanical coxa joints based on three-degree-of-freedom spherical parallel manipulators

International Nuclear Information System (INIS)

Li, Yanbiao; Ji, Shiming; Wang, Zhongfei; Jin, Mingsheng; Liu, Yi; Jin, Zhenlin

2013-01-01

We addressed the issue of the design of mechanical coxa joints based on three-degree-of-freedom spherical parallel manipulators using the parameter statistics optimum method based on index atlases. The coxa joints have the advantages of high payload, high accuracy, and good technological efficiency. The first step of the design and prototyping used in this paper develops the direct and inverse displacement equations from the layout feature of the mechanical coxa joints. Then, the shapes of a constant-orientation workspace of the mechanical coxa joints are described, and the effects of the design parameters on the workspace volume are studied quantitatively. The next step deals with the graphical representation of the atlases that illustrates the relationship between performance evaluation index and design parameters based on the kinematics and torque analysis of the mechanical coxa joints. Finally, the geometric parameters of the coxa joints are obtained by the parameter statistics optimum method based on the index atlases. Considering assembly conditions, the design scheme of the mechanical coxa joints is developed, which provides a theoretical basis for the application of the mechanical coxa joints.

Conjugate-Gradient Algorithms For Dynamics Of Manipulators

Science.gov (United States)

Fijany, Amir; Scheid, Robert E.

1993-01-01

Algorithms for serial and parallel computation of forward dynamics of multiple-link robotic manipulators by conjugate-gradient method developed. Parallel algorithms have potential for speedup of computations on multiple linked, specialized processors implemented in very-large-scale integrated circuits. Such processors used to stimulate dynamics, possibly faster than in real time, for purposes of planning and control.

A parallel robot to assist vitreoretinal surgery

Energy Technology Data Exchange (ETDEWEB)

Nakano, Taiga; Sugita, Naohiko; Mitsuishi, Mamoru [University of Tokyo, School of Engineering, Tokyo (Japan); Ueta, Takashi; Tamaki, Yasuhiro [University of Tokyo, Graduate School of Medicine, Tokyo (Japan)

2009-11-15

This paper describes the development and evaluation of a parallel prototype robot for vitreoretinal surgery where physiological hand tremor limits performance. The manipulator was specifically designed to meet requirements such as size, precision, and sterilization; this has six-degree-of-freedom parallel architecture and provides positioning accuracy with micrometer resolution within the eye. The manipulator is controlled by an operator with a ''master manipulator'' consisting of multiple joints. Results of the in vitro experiments revealed that when compared to the manual procedure, a higher stability and accuracy of tool positioning could be achieved using the prototype robot. This microsurgical system that we have developed has superior operability as compared to traditional manual procedure and has sufficient potential to be used clinically for vitreoretinal surgery. (orig.)

Workspace quality analysis and application for a completely restrained 3-Dof planar cable-driven parallel manipulator

International Nuclear Information System (INIS)

Tang, Xiaoqiang; Tang, Lewei; Wang, Jinsong; Sun, Dengfeng

2013-01-01

With the advantage of large workspace, low energy consumption and small inertia, the cable-driven parallel manipulator (CDPM) is suitable for heavy workpieces in rapid velocity and acceleration. We present a workspace analysis approach to solve force and torque equilibriums of completely restrained CDPMs. By this approach, not only the distribution but also the value of tensions driven by cables is investigated together. Two new indices, all cable tension distribution index (ACTDI) and area of the global quality workspace (AG) are proposed to evaluate the quality of the workspace. By concentrating on the workspace and its quality combined with the tension characteristics, these criteria are used to determine the optimal workspace in CDPMs. To verify the capacity of the proposed method, simulation examples are presented and the results demonstrate the approach's effectiveness. In the end, the dimensional design for a planar CDPM is discussed with the indices of workspace quality.

Kinematics and dynamics analysis of a novel serial-parallel dynamic simulator

Energy Technology Data Exchange (ETDEWEB)

Hu, Bo; Zhang, Lian Dong; Yu, Jingjing [Parallel Robot and Mechatronic System Laboratory of Hebei Province, Yanshan University, Qinhuangdao, Hebei (China)

2016-11-15

A serial-parallel dynamics simulator based on serial-parallel manipulator is proposed. According to the dynamics simulator motion requirement, the proposed serial-parallel dynamics simulator formed by 3-RRS (active revolute joint-revolute joint-spherical joint) and 3-SPR (Spherical joint-active prismatic joint-revolute joint) PMs adopts the outer and inner layout. By integrating the kinematics, constraint and coupling information of the 3-RRS and 3-SPR PMs into the serial-parallel manipulator, the inverse Jacobian matrix, velocity, and acceleration of the serial-parallel dynamics simulator are studied. Based on the principle of virtual work and the kinematics model, the inverse dynamic model is established. Finally, the workspace of the (3-RRS)+(3-SPR) dynamics simulator is constructed.

Kinematics and dynamics analysis of a novel serial-parallel dynamic simulator

International Nuclear Information System (INIS)

Hu, Bo; Zhang, Lian Dong; Yu, Jingjing

2016-01-01

A serial-parallel dynamics simulator based on serial-parallel manipulator is proposed. According to the dynamics simulator motion requirement, the proposed serial-parallel dynamics simulator formed by 3-RRS (active revolute joint-revolute joint-spherical joint) and 3-SPR (Spherical joint-active prismatic joint-revolute joint) PMs adopts the outer and inner layout. By integrating the kinematics, constraint and coupling information of the 3-RRS and 3-SPR PMs into the serial-parallel manipulator, the inverse Jacobian matrix, velocity, and acceleration of the serial-parallel dynamics simulator are studied. Based on the principle of virtual work and the kinematics model, the inverse dynamic model is established. Finally, the workspace of the (3-RRS)+(3-SPR) dynamics simulator is constructed

Workspace quality analysis and application for a completely restrained 3-Dof planar cable-driven parallel manipulator

Energy Technology Data Exchange (ETDEWEB)

Tang, Xiaoqiang; Tang, Lewei; Wang, Jinsong [Tsinghua University, Beijing (China); Sun, Dengfeng [Purdue University, West Lafayette (United States)

2013-08-15

With the advantage of large workspace, low energy consumption and small inertia, the cable-driven parallel manipulator (CDPM) is suitable for heavy workpieces in rapid velocity and acceleration. We present a workspace analysis approach to solve force and torque equilibriums of completely restrained CDPMs. By this approach, not only the distribution but also the value of tensions driven by cables is investigated together. Two new indices, all cable tension distribution index (ACTDI) and area of the global quality workspace (AG) are proposed to evaluate the quality of the workspace. By concentrating on the workspace and its quality combined with the tension characteristics, these criteria are used to determine the optimal workspace in CDPMs. To verify the capacity of the proposed method, simulation examples are presented and the results demonstrate the approach's effectiveness. In the end, the dimensional design for a planar CDPM is discussed with the indices of workspace quality.

Kinematics and Dynamics of an Asymmetrical Parallel Robotic Wrist

DEFF Research Database (Denmark)

Wu, Guanglei

2014-01-01

This paper introduces an asymmetrical parallel robotic wrist, which can generate a decoupled unlimited-torsion motion and achieve high positioning accuracy. The kinematics, dexterity, and singularities of the manipulator are investigated to visualize the performance contours of the manipulator...

An inertial parameter identification method of eliminating system damping effect for a six-degree-of-freedom parallel manipulator

Directory of Open Access Journals (Sweden)

Tian Tixian

2015-04-01

Full Text Available A new simple and effective inertial parameter identification method based on sinusoidal vibrations of a six-degree-of-freedom parallel manipulator is proposed. Compared with previously known identification algorithms, the advantages of the new approach are there is no need to design the excitation trajectory to consider the condition number of the observation matrix and the inertial matrix can be accurately defined regardless of the effect of viscous friction. In addition, the use of a sinusoidal exciting trajectory allows calculation of the velocities and accelerations from the measured position response. Simulations show that the new approach has acceptable tolerance of dry friction when using a simple coupling parameter modified formula. The experimental application to the hydraulically driven Stewart platform demonstrates the capability and efficiency of the proposed identification method.

Electrostatic Transport and Manipulation of Lunar Soil and Dust

International Nuclear Information System (INIS)

Kawamoto, Hiroyuki

2008-01-01

Transport and manipulation technologies of lunar soil and dust are under development utilizing the electrostatic force. Transport of particles is realized by an electrostatic conveyer consisting of parallel electrodes. Four-phase traveling electrostatic wave was applied to the electrodes to transport particles upon the conveyer and it was demonstrated that particles were efficiently transported under conditions of low frequency, high voltage, and the application of rectangular wave. Not only linear but also curved and closed transport was demonstrated. Numerical investigation was carried out with a three-dimensional hard-sphere model of the Distinct Element Method to clarify the mechanism of the transport and to predict performances in the lunar environment. This technology is expected to be utilized not only for the transport of bulk soil but also for the cleaning of a solar panel and an optical lens. Another technology is an electrostatic manipulation system to manipulate single particle. A manipulator consisted of two parallel pin electrodes. When voltage was applied between the electrodes, electrophoresis force generated in non-uniform electrostatic field was applied to the particle near the tip of the electrode. The particle was captured by the application of the voltage and released from the manipulator by turning off the voltage. It was possible to manipulate not only insulative but also conductive particles. Three-dimensional electrostatic field calculation was conducted to calculate the electrophoresis force and the Coulomb force

Grasp planning for a reconfigurable parallel robot with an underactuated arm structure

Directory of Open Access Journals (Sweden)

M. Riedel

2010-12-01

Full Text Available In this paper, a novel approach of grasp planning is applied to find out the appropriate grasp points for a reconfigurable parallel robot called PARAGRIP (Parallel Gripping. This new handling system is able to manipulate objects in the six-dimensional Cartesian space by several robotic arms using only six actuated joints. After grasping, the contact elements at the end of the underactuated arm mechanisms are connected to the object which forms a closed loop mechanism similar to the architecture of parallel manipulators. As the mounting and grasp points of the arms can easily be changed, the manipulator can be reconfigured to match the user's preferences and needs. This paper raises the question, how and where these grasp points are to be placed on the object to perform well for a certain manipulation task.

This paper was presented at the IFToMM/ASME International Workshop on Underactuated Grasping (UG2010, 19 August 2010, Montréal, Canada.

Active Vibration Suppression of a 3-DOF Flexible Parallel Manipulator Using Efficient Modal Control

Directory of Open Access Journals (Sweden)

Quan Zhang

2014-01-01

Full Text Available This paper addresses the dynamic modeling and efficient modal control of a planar parallel manipulator (PPM with three flexible linkages actuated by linear ultrasonic motors (LUSM. To achieve active vibration control, multiple lead zirconate titanate (PZT transducers are mounted on the flexible links as vibration sensors and actuators. Based on Lagrange’s equations, the dynamic model of the flexible links is derived with the dynamics of PZT actuators incorporated. Using the assumed mode method (AMM, the elastic motion of the flexible links are discretized under the assumptions of pinned-free boundary conditions, and the assumed mode shapes are validated through experimental modal test. Efficient modal control (EMC, in which the feedback forces in different modes are determined according to the vibration amplitude or energy of their own, is employed to control the PZT actuators to realize active vibration suppression. Modal filters are developed to extract the modal displacements and velocities from the vibration sensors. Numerical simulation and vibration control experiments are conducted to verify the proposed dynamic model and controller. The results show that the EMC method has the capability of suppressing multimode vibration simultaneously, and both the structural and residual vibrations of the flexible links are effectively suppressed using EMC approach.

Ion manipulation method and device

Energy Technology Data Exchange (ETDEWEB)

Anderson, Gordon A.; Baker, Erin M.; Smith, Richard D.; Ibrahim, Yehia M.

2017-11-07

An ion manipulation method and device is disclosed. The device includes a pair of substantially parallel surfaces. An array of inner electrodes is contained within, and extends substantially along the length of, each parallel surface. The device includes a first outer array of electrodes and a second outer array of electrodes. Each outer array of electrodes is positioned on either side of the inner electrodes, and is contained within and extends substantially along the length of each parallel surface. A DC voltage is applied to the first and second outer array of electrodes. A RF voltage, with a superimposed electric field, is applied to the inner electrodes by applying the DC voltages to each electrode. Ions either move between the parallel surfaces within an ion confinement area or along paths in the direction of the electric field, or can be trapped in the ion confinement area.

Topological Structure of Manipulators Used in Amusement Parks

Directory of Open Access Journals (Sweden)

Liviu Marian Ungureanu

2014-06-01

Full Text Available This paper focuses on the mobility analysis of spatial and planar manipulators used in amusement parks. In this paper is presented a topological structure analysis for many types of serial and parallel manipulators, referring to the calculation of mobility (degree of freedom of these types of complex mechanisms. It is used a new formula to calculate the mobility according to the number of drivelines, which are considered having identical operations.

Kinematics/statics analysis of a novel serial-parallel robotic arm with hand

Energy Technology Data Exchange (ETDEWEB)

Lu, Yi; Dai, Zhuohong; Ye, Nijia; Wang, Peng [Yanshan University, Hebei (China)

2015-10-15

A robotic arm with fingered hand generally has multi-functions to complete various complicated operations. A novel serial-parallel robotic arm with a hand is proposed and its kinematics and statics are studied systematically. A 3D prototype of the serial-parallel robotic arm with a hand is constructed and analyzed by simulation. The serial-parallel robotic arm with a hand is composed of an upper 3RPS parallel manipulator, a lower 3SPR parallel manipulator and a hand with three finger mechanisms. Its kinematics formulae for solving the displacement, velocity, acceleration of are derived. Its statics formula for solving the active/constrained forces is derived. Its reachable workspace and orientation workspace are constructed and analyzed. Finally, an analytic example is given for solving the kinematics and statics of the serial-parallel robotic arm with a hand and the analytic solutions are verified by a simulation mechanism.

Kinematics/statics analysis of a novel serial-parallel robotic arm with hand

International Nuclear Information System (INIS)

Lu, Yi; Dai, Zhuohong; Ye, Nijia; Wang, Peng

2015-01-01

A robotic arm with fingered hand generally has multi-functions to complete various complicated operations. A novel serial-parallel robotic arm with a hand is proposed and its kinematics and statics are studied systematically. A 3D prototype of the serial-parallel robotic arm with a hand is constructed and analyzed by simulation. The serial-parallel robotic arm with a hand is composed of an upper 3RPS parallel manipulator, a lower 3SPR parallel manipulator and a hand with three finger mechanisms. Its kinematics formulae for solving the displacement, velocity, acceleration of are derived. Its statics formula for solving the active/constrained forces is derived. Its reachable workspace and orientation workspace are constructed and analyzed. Finally, an analytic example is given for solving the kinematics and statics of the serial-parallel robotic arm with a hand and the analytic solutions are verified by a simulation mechanism.

Analysis of a closed-kinematic chain robot manipulator

Science.gov (United States)

Nguyen, Charles C.; Pooran, Farhad J.

1988-01-01

Presented are the research results from the research grant entitled: Active Control of Robot Manipulators, sponsored by the Goddard Space Flight Center (NASA) under grant number NAG-780. This report considers a class of robot manipulators based on the closed-kinematic chain mechanism (CKCM). This type of robot manipulators mainly consists of two platforms, one is stationary and the other moving, and they are coupled together through a number of in-parallel actuators. Using spatial geometry and homogeneous transformation, a closed-form solution is derived for the inverse kinematic problem of the six-degree-of-freedom manipulator, built to study robotic assembly in space. Iterative Newton Raphson method is employed to solve the forward kinematic problem. Finally, the equations of motion of the above manipulators are obtained by employing the Lagrangian method. Study of the manipulator dynamics is performed using computer simulation whose results show that the robot actuating forces are strongly dependent on the mass and centroid locations of the robot links.

Vision feedback driven automated assembly of photopolymerized structures by parallel optical trapping and manipulation

DEFF Research Database (Denmark)

Dam, Jeppe Seidelin; Perch-Nielsen, Ivan Ryberg; Rodrigo, Peter John

2007-01-01

We demonstrate how optical trapping and manipulation can be used to assemble microstructures. The microstructures we show being automatically recognized and manipulated are produced using the two-photon polymerization (2PP) technique with submicron resolution. In this work, we show identical shape...

Finding Optimal Independent Grasp Regions of Parallel Manipulators with Additional Applications for Limbed Robot Mobility

Data.gov (United States)

National Aeronautics and Space Administration — For the problem of robotic manipulation, wherein a robotic manipulator interacts with objects or its environment using an end-effector (gripper), there have been...

Optoelectronic Tweezers for Microparticle and Cell Manipulation

Science.gov (United States)

Wu, Ming Chiang (Inventor); Chiou, Pei-Yu (Inventor); Ohta, Aaron T. (Inventor)

2014-01-01

An optical image-driven light induced dielectrophoresis (DEP) apparatus and method are described which provide for the manipulation of particles or cells with a diameter on the order of 100 micromillimeters or less. The apparatus is referred to as optoelectric tweezers (OET) and provides a number of advantages over conventional optical tweezers, in particular the ability to perform operations in parallel and over a large area without damage to living cells. The OET device generally comprises a planar liquid-filled structure having one or more portions which are photoconductive to convert incoming light to a change in the electric field pattern. The light patterns are dynamically generated to provide a number of manipulation structures that can manipulate single particles and cells or group of particles/cells. The OET preferably includes a microscopic imaging means to provide feedback for the optical manipulation, such as detecting position and characteristics wherein the light patterns are modulated accordingly.

Scale-up for model verification; design, modeling and control of an elastic parallel kinematic 6-DOFs manipulator

NARCIS (Netherlands)

Huijts, Martijn; Brouwer, Dannis Michel; van Dijk, Johannes

2009-01-01

Manipulators with guidance constructions based on elastic mechanisms are of interest for the increasing number of precision vacuum applications. Previously, the design of an elastic MEMS-based 6-DOFs manipulator was presented. Characterization in six degrees of freedom (DOFs) of a manipulator the

A kinematic analysis of the modified flight telerobotic servicer manipulator system

Science.gov (United States)

Crane, Carl; Carnahan, Tim; Duffy, Joseph

1992-01-01

A reverse kinematic analysis is presented of a six-DOF subchain of a modified seven-DOF flight telerobotic servicer manipulator system. The six-DOF subchain is designated as a TR-RT chain, which describes the sequence of manipulator joints beginning with the first grounded hook joint (universal joint) T, where the sequence R-R designates a pair of revolute joints with parallel axes. At the outset, it had been thought that the reverse kinematic analysis would be similar to a TTT manipulator previously analyzed, in which the third and fourth joints intersected at a finite point. However, this is shown not the case, and a 16th-degree tan-half-angle polynomial is derived for the TR-RT manipulator.

Why do spinal manipulation techniques take the form they do? Towards a general model of spinal manipulation.

Science.gov (United States)

Evans, David W

2010-06-01

For centuries, techniques used to manipulate joints in the spine have been passed down from one generation of manipulators to the next. Today, spinal manipulation is in the curious position that positive clinical effects have now been demonstrated, yet the theoretical base underpinning every aspect of its use is still underdeveloped. An important question is posed in this masterclass: why do spinal manipulation techniques take the form they do? From the available literature, two factors appear to provide an answer: 1. Action of a force upon vertebrae. Any 'direct' spinal manipulation technique requires that the patient be orientated in such a way that force is applied perpendicular to the overlying skin surface so as to act upon the vertebrae beneath. If the vertebral motion produced by 'directly' applied force is insufficient to produce the desired effect (e.g. cavitation), then force must be applied 'indirectly', often through remote body segments such as the head, thorax, abdomen, pelvis, and extremities. 2. Spinal segment morphology. A new hypothesis is presented. Spinal manipulation techniques exploit the morphology of vertebrae by inducing rotation at a spinal segment, about an axis that is always parallel to the articular surfaces of the constituent zygapophysial joints. In doing so, the articular surfaces of one zygapophysial joint appose to the point of contact, resulting in migration of the axis of rotation towards these contacting surfaces, and in turn this facilitates gapping of the other (target) zygapophysial joint. Other variations in the form of spinal manipulation techniques are likely to depend upon the personal style and individual choices of the practitioner.

Modular manual control device for manipulators

International Nuclear Information System (INIS)

Dzholdasbekov, U.A.; Lukyanov, A.T.; Slutsky, L.I.; Safontsev, E.A.; Dzhamalov, N.K.

1991-01-01

The device described in this patent comprises a base, a series of connected modules, each with a position pickup and a handle. One module is provided for each degree of mobility of the manipulator being controlled; the modular construction enables the control of manipulators with differing degrees of mobility. One rotary movement module and three orthogonal linear movement modules are provided. Each linear module has two parallel guides between which a carriage is supported for movement by balls. The position pickup is provided on the carriage. The rotary module comprises inner and outer casings, relative movement of which is detected by pickup. Further rotary pickups may be provided for rotation about axes. A close/open switch and a speed control pickup may also be provided. (author)

Soft Robotic Manipulation of Onions and Artichokes in the Food Industry

Directory of Open Access Journals (Sweden)

R. Morales

2014-04-01

Full Text Available This paper presents the development of a robotic solution for a problem of fast manipulation and handling of onions or artichokes in the food industry. The complete solution consists of a parallel robotic manipulatior, a specially designed end-effector based on a customized vacuum suction cup, and a computer vision software developed for pick and place operations. First, the selection and design process of the proposed robotic solution to fit with the initial requeriments is presented, including the customized vacuum suction cup. Then, the kinematic analysis of the parallel manipulator needed to develop the robot control system is reviewed. Moreover, computer vision application is presented inthe paper. Hardware details of the implementation of the building prototype are also shown. Finally, conclusions and future work show the current status of the project.

Simulation of the Lumbar Spine as a Multi-Module Paralel Manipulator

Directory of Open Access Journals (Sweden)

M. Ceccarelli

2011-01-01

Full Text Available In this paper a simulation of movements of lumbar spine is proposed by using a model with serially connected parallel manipulators. An analysis has been computed for the human spine structure and its movements, in order to simulate the motions and forces that actuate a spine specifically in the lumbar segment. A mechanical model has been designed with available identified parameters of human spine, by using characteristics of parallel manipulators and spring stiffness. This model is suitable to properly simulate the trunk behavior at macroscopic level but also the smooth behavior of intervertebral discs and actuating motions of muscles and tendons. Simulation results for spring actions and joints reaction forces can give an evaluation of the forces that intervertebral discs supports during motions of a real spine.

An integrated open-cavity system for magnetic bead manipulation.

Science.gov (United States)

Abu-Nimeh, F T; Salem, F M

2013-02-01

Superparamagnetic beads are increasingly used in biomedical assays to manipulate, transport, and maneuver biomaterials. We present a low-cost integrated system designed in bulk CMOS to manipulate and separate biomedical magnetic beads. The system consists of 8 × 8 coil-arrays suitable for single bead manipulation, or collaborative multi-bead manipulation, using pseudo-parallel executions. We demonstrate the flexibility of the design in terms of different coil sizes, DC current levels, and layout techniques. In one array module example, the size of a single coil is 30 μm × 30 μm and the full array occupies an area of 248 μm × 248 μm in 0.5 μm CMOS technology. The programmable DC current source supports 8 discrete levels up to 1.5 mA. The total power consumption of the entire module is 9 mW when running at full power.

Pneumatic artificial muscle actuators for compliant robotic manipulators

Science.gov (United States)

Robinson, Ryan Michael

Robotic systems are increasingly being utilized in applications that require interaction with humans. In order to enable safe physical human-robot interaction, light weight and compliant manipulation are desirable. These requirements are problematic for many conventional actuation systems, which are often heavy, and typically use high stiffness to achieve high performance, leading to large impact forces upon collision. However, pneumatic artificial muscles (PAMs) are actuators that can satisfy these safety requirements while offering power-to-weight ratios comparable to those of conventional actuators. PAMs are extremely lightweight actuators that produce force in response to pressurization. These muscles demonstrate natural compliance, but have a nonlinear force-contraction profile that complicates modeling and control. This body of research presents solutions to the challenges associated with the implementation of PAMs as actuators in robotic manipulators, particularly with regard to modeling, design, and control. An existing PAM force balance model was modified to incorporate elliptic end geometry and a hyper-elastic constitutive relationship, dramatically improving predictions of PAM behavior at high contraction. Utilizing this improved model, two proof-of-concept PAM-driven manipulators were designed and constructed; design features included parallel placement of actuators and a tendon-link joint design. Genetic algorithm search heuristics were employed to determine an optimal joint geometry; allowing a manipulator to achieve a desired torque profile while minimizing the required PAM pressure. Performance of the manipulators was evaluated in both simulation and experiment employing various linear and nonlinear control strategies. These included output feedback techniques, such as proportional-integral-derivative (PID) and fuzzy logic, a model-based control for computed torque, and more advanced controllers, such as sliding mode, adaptive sliding mode, and

Three-dimensional mid-air acoustic manipulation by ultrasonic phased arrays.

Science.gov (United States)

Ochiai, Yoichi; Hoshi, Takayuki; Rekimoto, Jun

2014-01-01

The essence of levitation technology is the countervailing of gravity. It is known that an ultrasound standing wave is capable of suspending small particles at its sound pressure nodes. The acoustic axis of the ultrasound beam in conventional studies was parallel to the gravitational force, and the levitated objects were manipulated along the fixed axis (i.e. one-dimensionally) by controlling the phases or frequencies of bolted Langevin-type transducers. In the present study, we considered extended acoustic manipulation whereby millimetre-sized particles were levitated and moved three-dimensionally by localised ultrasonic standing waves, which were generated by ultrasonic phased arrays. Our manipulation system has two original features. One is the direction of the ultrasound beam, which is arbitrary because the force acting toward its centre is also utilised. The other is the manipulation principle by which a localised standing wave is generated at an arbitrary position and moved three-dimensionally by opposed and ultrasonic phased arrays. We experimentally confirmed that expanded-polystyrene particles of 0.6 mm, 1 mm, and 2 mm in diameter could be manipulated by our proposed method.

Iteration schemes for parallelizing models of superconductivity

Energy Technology Data Exchange (ETDEWEB)

Gray, P.A. [Michigan State Univ., East Lansing, MI (United States)

1996-12-31

The time dependent Lawrence-Doniach model, valid for high fields and high values of the Ginzburg-Landau parameter, is often used for studying vortex dynamics in layered high-T{sub c} superconductors. When solving these equations numerically, the added degrees of complexity due to the coupling and nonlinearity of the model often warrant the use of high-performance computers for their solution. However, the interdependence between the layers can be manipulated so as to allow parallelization of the computations at an individual layer level. The reduced parallel tasks may then be solved independently using a heterogeneous cluster of networked workstations connected together with Parallel Virtual Machine (PVM) software. Here, this parallelization of the model is discussed and several computational implementations of varying degrees of parallelism are presented. Computational results are also given which contrast properties of convergence speed, stability, and consistency of these implementations. Included in these results are models involving the motion of vortices due to an applied current and pinning effects due to various material properties.

Acoustic Resonator Optimisation for Airborne Particle Manipulation

Science.gov (United States)

Devendran, Citsabehsan; Billson, Duncan R.; Hutchins, David A.; Alan, Tuncay; Neild, Adrian

Advances in micro-electromechanical systems (MEMS) technology and biomedical research necessitate micro-machined manipulators to capture, handle and position delicate micron-sized particles. To this end, a parallel plate acoustic resonator system has been investigated for the purposes of manipulation and entrapment of micron sized particles in air. Numerical and finite element modelling was performed to optimise the design of the layered acoustic resonator. To obtain an optimised resonator design, careful considerations of the effect of thickness and material properties are required. Furthermore, the effect of acoustic attenuation which is dependent on frequency is also considered within this study, leading to an optimum operational frequency range. Finally, experimental results demonstrated good particle levitation and capture of various particle properties and sizes ranging to as small as 14.8 μm.

Simulation Exploration through Immersive Parallel Planes

Energy Technology Data Exchange (ETDEWEB)

Brunhart-Lupo, Nicholas J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bush, Brian W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gruchalla, Kenny M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Smith, Steve [Los Alamos Visualization Associates

2017-05-25

We present a visualization-driven simulation system that tightly couples systems dynamics simulations with an immersive virtual environment to allow analysts to rapidly develop and test hypotheses in a high-dimensional parameter space. To accomplish this, we generalize the two-dimensional parallel-coordinates statistical graphic as an immersive 'parallel-planes' visualization for multivariate time series emitted by simulations running in parallel with the visualization. In contrast to traditional parallel coordinate's mapping the multivariate dimensions onto coordinate axes represented by a series of parallel lines, we map pairs of the multivariate dimensions onto a series of parallel rectangles. As in the case of parallel coordinates, each individual observation in the dataset is mapped to a polyline whose vertices coincide with its coordinate values. Regions of the rectangles can be 'brushed' to highlight and select observations of interest: a 'slider' control allows the user to filter the observations by their time coordinate. In an immersive virtual environment, users interact with the parallel planes using a joystick that can select regions on the planes, manipulate selection, and filter time. The brushing and selection actions are used to both explore existing data as well as to launch additional simulations corresponding to the visually selected portions of the input parameter space. As soon as the new simulations complete, their resulting observations are displayed in the virtual environment. This tight feedback loop between simulation and immersive analytics accelerates users' realization of insights about the simulation and its output.

Three-dimensional mid-air acoustic manipulation by ultrasonic phased arrays.

Directory of Open Access Journals (Sweden)

Yoichi Ochiai

Full Text Available The essence of levitation technology is the countervailing of gravity. It is known that an ultrasound standing wave is capable of suspending small particles at its sound pressure nodes. The acoustic axis of the ultrasound beam in conventional studies was parallel to the gravitational force, and the levitated objects were manipulated along the fixed axis (i.e. one-dimensionally by controlling the phases or frequencies of bolted Langevin-type transducers. In the present study, we considered extended acoustic manipulation whereby millimetre-sized particles were levitated and moved three-dimensionally by localised ultrasonic standing waves, which were generated by ultrasonic phased arrays. Our manipulation system has two original features. One is the direction of the ultrasound beam, which is arbitrary because the force acting toward its centre is also utilised. The other is the manipulation principle by which a localised standing wave is generated at an arbitrary position and moved three-dimensionally by opposed and ultrasonic phased arrays. We experimentally confirmed that expanded-polystyrene particles of 0.6 mm, 1 mm, and 2 mm in diameter could be manipulated by our proposed method.

Design, analysis and control of cable-suspended parallel robots and its applications

CERN Document Server

Zi, Bin

2017-01-01

This book provides an essential overview of the authors’ work in the field of cable-suspended parallel robots, focusing on innovative design, mechanics, control, development and applications. It presents and analyzes several typical mechanical architectures of cable-suspended parallel robots in practical applications, including the feed cable-suspended structure for super antennae, hybrid-driven-based cable-suspended parallel robots, and cooperative cable parallel manipulators for multiple mobile cranes. It also addresses the fundamental mechanics of cable-suspended parallel robots on the basis of their typical applications, including the kinematics, dynamics and trajectory tracking control of the feed cable-suspended structure for super antennae. In addition it proposes a novel hybrid-driven-based cable-suspended parallel robot that uses integrated mechanism design methods to improve the performance of traditional cable-suspended parallel robots. A comparative study on error and performance indices of hybr...

Kinematics and dynamics of a six-degree-of-freedom robot manipulator with closed kinematic chain mechanism

Science.gov (United States)

Nguyen, Charles C.; Pooran, Farhad J.

1989-01-01

This paper deals with a class of robot manipulators built based on the kinematic chain mechanism (CKCM). This class of CKCM manipulators consists of a fixed and a moving platform coupled together via a number of in-parallel actuators. A closed-form solution is derived for the inverse kinematic problem of a six-degre-of-freedom CKCM manipulator designed to study robotic applications in space. Iterative Newton-Raphson method is employed to solve the forward kinematic problem. Dynamics of the above manipulator is derived using the Lagrangian approach. Computer simulation of the dynamical equations shows that the actuating forces are strongly dependent on the mass and centroid of the robot links.

Dynamic Model and Vibration Characteristics of Planar 3-RRR Parallel Manipulator with Flexible Intermediate Links considering Exact Boundary Conditions

Directory of Open Access Journals (Sweden)

Lianchao Sheng

2017-01-01

Full Text Available Due to the complexity of the dynamic model of a planar 3-RRR flexible parallel manipulator (FPM, it is often difficult to achieve active vibration control algorithm based on the system dynamic model. To establish a simple and efficient dynamic model of the planar 3-RRR FPM to study its dynamic characteristics and build a controller conveniently, firstly, considering the effect of rigid-flexible coupling and the moment of inertia at the end of the flexible intermediate link, the modal function is determined with the pinned-free boundary condition. Then, considering the main vibration modes of the system, a high-efficiency coupling dynamic model is established on the basis of guaranteeing the model control accuracy. According to the model, the modal characteristics of the flexible intermediate link are analyzed and compared with the modal test results. The results show that the model can effectively reflect the main vibration modes of the planar 3-RRR FPM; in addition the model can be used to analyze the effects of inertial and coupling forces on the dynamics model and the drive torque of the drive motor. Because this model is of the less dynamic parameters, it is convenient to carry out the control program.

Kinematics of a Hybrid Manipulator by Means of Screw Theory

International Nuclear Information System (INIS)

Gallardo-Alvarado, J

2005-01-01

In this work the kinematics of a hybrid manipulator, namely a fully parallel-serial manipulator, with a particular topology is approached by means of the theory of screws. Given the length of the six independent limbs, the forward position analysis of the mechanism under study, indeed the computation of the resulting pose, position and orientation, of the end-platform with respect to the fixed platform, is carried out in closed-form solution. Therefore conveniently this initial analysis avoids the use of a numerical technique such as the Newton-Raphson method. Writing in screw form the reduced acceleration state of the translational platform, with respect to the fixed platform, a simple expression for the computation of the acceleration of the translational platform is derived by taking advantage of the properties of reciprocal screws, via the Klein form, a bilinear symmetric form of the Lie algebra e(3). Following a similar procedure, a simple expression for the computation of the angular acceleration of the end-platform, with respect to the translational platform, is easily derived. Naturally, as an intermediate step, this contribution also provides the forward and inverse velocity analyses of the chosen parallel-serial manipulator. Finally, in order to prove the versatility of the expressions obtained via screw theory for solving the kinematics, up to the acceleration analysis, of the proposed spatial mechanism, a numerical example is solved with the help of commercial computer codes

Development of structural schemes of parallel structure manipulators using screw calculus

Science.gov (United States)

Rashoyan, G. V.; Shalyukhin, K. A.; Gaponenko, EV

2018-03-01

The paper considers the approach to the structural analysis and synthesis of parallel structure robots based on the mathematical apparatus of groups of screws and on a concept of reciprocity of screws. The results are depicted of synthesis of parallel structure robots with different numbers of degrees of freedom, corresponding to the different groups of screws. Power screws are applied with this aim, based on the principle of static-kinematic analogy; the power screws are similar to the orts of axes of not driven kinematic pairs of a corresponding connecting chain. Accordingly, kinematic screws of the outlet chain of a robot are simultaneously determined which are reciprocal to power screws of kinematic sub-chains. Solution of certain synthesis problems is illustrated with practical applications. Closed groups of screws can have eight types. The three-membered groups of screws are of greatest significance, as well as four-membered screw groups [1] and six-membered screw groups. Three-membered screw groups correspond to progressively guiding mechanisms, to spherical mechanisms, and to planar mechanisms. The four-membered group corresponds to the motion of the SCARA robot. The six-membered group includes all possible motions. From the works of A.P. Kotelnikov, F.M. Dimentberg, it is known that closed fifth-order screw groups do not exist. The article presents examples of the mechanisms corresponding to the given groups.

PEM-PCA: A Parallel Expectation-Maximization PCA Face Recognition Architecture

Directory of Open Access Journals (Sweden)

Kanokmon Rujirakul

2014-01-01

Full Text Available Principal component analysis or PCA has been traditionally used as one of the feature extraction techniques in face recognition systems yielding high accuracy when requiring a small number of features. However, the covariance matrix and eigenvalue decomposition stages cause high computational complexity, especially for a large database. Thus, this research presents an alternative approach utilizing an Expectation-Maximization algorithm to reduce the determinant matrix manipulation resulting in the reduction of the stages’ complexity. To improve the computational time, a novel parallel architecture was employed to utilize the benefits of parallelization of matrix computation during feature extraction and classification stages including parallel preprocessing, and their combinations, so-called a Parallel Expectation-Maximization PCA architecture. Comparing to a traditional PCA and its derivatives, the results indicate lower complexity with an insignificant difference in recognition precision leading to high speed face recognition systems, that is, the speed-up over nine and three times over PCA and Parallel PCA.

PEM-PCA: a parallel expectation-maximization PCA face recognition architecture.

Science.gov (United States)

Rujirakul, Kanokmon; So-In, Chakchai; Arnonkijpanich, Banchar

2014-01-01

Principal component analysis or PCA has been traditionally used as one of the feature extraction techniques in face recognition systems yielding high accuracy when requiring a small number of features. However, the covariance matrix and eigenvalue decomposition stages cause high computational complexity, especially for a large database. Thus, this research presents an alternative approach utilizing an Expectation-Maximization algorithm to reduce the determinant matrix manipulation resulting in the reduction of the stages' complexity. To improve the computational time, a novel parallel architecture was employed to utilize the benefits of parallelization of matrix computation during feature extraction and classification stages including parallel preprocessing, and their combinations, so-called a Parallel Expectation-Maximization PCA architecture. Comparing to a traditional PCA and its derivatives, the results indicate lower complexity with an insignificant difference in recognition precision leading to high speed face recognition systems, that is, the speed-up over nine and three times over PCA and Parallel PCA.

Simulation Exploration through Immersive Parallel Planes: Preprint

Energy Technology Data Exchange (ETDEWEB)

Brunhart-Lupo, Nicholas; Bush, Brian W.; Gruchalla, Kenny; Smith, Steve

2016-03-01

We present a visualization-driven simulation system that tightly couples systems dynamics simulations with an immersive virtual environment to allow analysts to rapidly develop and test hypotheses in a high-dimensional parameter space. To accomplish this, we generalize the two-dimensional parallel-coordinates statistical graphic as an immersive 'parallel-planes' visualization for multivariate time series emitted by simulations running in parallel with the visualization. In contrast to traditional parallel coordinate's mapping the multivariate dimensions onto coordinate axes represented by a series of parallel lines, we map pairs of the multivariate dimensions onto a series of parallel rectangles. As in the case of parallel coordinates, each individual observation in the dataset is mapped to a polyline whose vertices coincide with its coordinate values. Regions of the rectangles can be 'brushed' to highlight and select observations of interest: a 'slider' control allows the user to filter the observations by their time coordinate. In an immersive virtual environment, users interact with the parallel planes using a joystick that can select regions on the planes, manipulate selection, and filter time. The brushing and selection actions are used to both explore existing data as well as to launch additional simulations corresponding to the visually selected portions of the input parameter space. As soon as the new simulations complete, their resulting observations are displayed in the virtual environment. This tight feedback loop between simulation and immersive analytics accelerates users' realization of insights about the simulation and its output.

A review of magnetic resonance imaging compatible manipulators in surgery.

Science.gov (United States)

Elhawary, H; Zivanovic, A; Davies, B; Lampérth, M

2006-04-01

Developments in magnetic resonance imaging (MRI), coupled with parallel progress in the field of computer-assisted surgery, mean that an ideal environment has been created for the development of MRI-compatible robotic systems and manipulators, capable of enhancing many types of surgical procedure. However, MRI does impose severe restrictions on mechatronic devices to be used in or around the scanners. In this article a review of the developments in the field of MRI-compatible surgical manipulators over the last decade is presented. The manipulators developed make use of different methods of actuation, but they can be reduced to four main groups: actuation transmitted through hydraulics, pneumatic actuators, ultrasonic motors based on the piezoceramic principle and remote manual actuation. Progress has been made concerning material selection, position sensing, and different actuation techniques, and design strategies have been implemented to overcome the multiple restrictions imposed by the MRI environment. Most systems lack the clinical validation needed to continue on to commercial products.

Use of Parallel Micro-Platform for the Simulation the Space Exploration

Science.gov (United States)

Velasco Herrera, Victor Manuel; Velasco Herrera, Graciela; Rosano, Felipe Lara; Rodriguez Lozano, Salvador; Lucero Roldan Serrato, Karen

The purpose of this work is to create a parallel micro-platform, that simulates the virtual movements of a space exploration in 3D. One of the innovations presented in this design consists of the application of a lever mechanism for the transmission of the movement. The development of such a robot is a challenging task very different of the industrial manipulators due to a totally different target system of requirements. This work presents the study and simulation, aided by computer, of the movement of this parallel manipulator. The development of this model has been developed using the platform of computer aided design Unigraphics, in which it was done the geometric modeled of each one of the components and end assembly (CAD), the generation of files for the computer aided manufacture (CAM) of each one of the pieces and the kinematics simulation of the system evaluating different driving schemes. We used the toolbox (MATLAB) of aerospace and create an adaptive control module to simulate the system.

A language for data-parallel and task parallel programming dedicated to multi-SIMD computers. Contributions to hydrodynamic simulation with lattice gases

International Nuclear Information System (INIS)

Pic, Marc Michel

1995-01-01

Parallel programming covers task-parallelism and data-parallelism. Many problems need both parallelisms. Multi-SIMD computers allow hierarchical approach of these parallelisms. The T++ language, based on C++, is dedicated to exploit Multi-SIMD computers using a programming paradigm which is an extension of array-programming to tasks managing. Our language introduced array of independent tasks to achieve separately (MIMD), on subsets of processors of identical behaviour (SIMD), in order to translate the hierarchical inclusion of data-parallelism in task-parallelism. To manipulate in a symmetrical way tasks and data we propose meta-operations which have the same behaviour on tasks arrays and on data arrays. We explain how to implement this language on our parallel computer SYMPHONIE in order to profit by the locally-shared memory, by the hardware virtualization, and by the multiplicity of communications networks. We analyse simultaneously a typical application of such architecture. Finite elements scheme for Fluid mechanic needs powerful parallel computers and requires large floating points abilities. Lattice gases is an alternative to such simulations. Boolean lattice bases are simple, stable, modular, need to floating point computation, but include numerical noise. Boltzmann lattice gases present large precision of computation, but needs floating points and are only locally stable. We propose a new scheme, called multi-bit, who keeps the advantages of each boolean model to which it is applied, with large numerical precision and reduced noise. Experiments on viscosity, physical behaviour, noise reduction and spurious invariants are shown and implementation techniques for parallel Multi-SIMD computers detailed. (author) [fr

Dynamic modeling and hierarchical compound control of a novel 2-DOF flexible parallel manipulator with multiple actuation modes

Science.gov (United States)

Liang, Dong; Song, Yimin; Sun, Tao; Jin, Xueying

2018-03-01

This paper addresses the problem of rigid-flexible coupling dynamic modeling and active control of a novel flexible parallel manipulator (PM) with multiple actuation modes. Firstly, based on the flexible multi-body dynamics theory, the rigid-flexible coupling dynamic model (RFDM) of system is developed by virtue of the augmented Lagrangian multipliers approach. For completeness, the mathematical models of permanent magnet synchronous motor (PMSM) and piezoelectric transducer (PZT) are further established and integrated with the RFDM of mechanical system to formulate the electromechanical coupling dynamic model (ECDM). To achieve the trajectory tracking and vibration suppression, a hierarchical compound control strategy is presented. Within this control strategy, the proportional-differential (PD) feedback controller is employed to realize the trajectory tracking of end-effector, while the strain and strain rate feedback (SSRF) controller is developed to restrain the vibration of the flexible links using PZT. Furthermore, the stability of the control algorithm is demonstrated based on the Lyapunov stability theory. Finally, two simulation case studies are performed to illustrate the effectiveness of the proposed approach. The results indicate that, under the redundant actuation mode, the hierarchical compound control strategy can guarantee the flexible PM achieves singularity-free motion and vibration attenuation within task workspace simultaneously. The systematic methodology proposed in this study can be conveniently extended for the dynamic modeling and efficient controller design of other flexible PMs, especially the emerging ones with multiple actuation modes.

A Parallel Modular Biomimetic Cilia Sorting Platform

Directory of Open Access Journals (Sweden)

James G. H. Whiting

2018-03-01

Full Text Available The aquatic unicellular organism Paramecium caudatum uses cilia to swim around its environment and to graze on food particles and bacteria. Paramecia use waves of ciliary beating for locomotion, intake of food particles and sensing. There is some evidence that Paramecia pre-sort food particles by discarding larger particles, but intake the particles matching their mouth cavity. Most prior attempts to mimic cilia-based manipulation merely mimicked the overall action rather than the beating of cilia. The majority of massive-parallel actuators are controlled by a central computer; however, a distributed control would be far more true-to-life. We propose and test a distributed parallel cilia platform where each actuating unit is autonomous, yet exchanging information with its closest neighboring units. The units are arranged in a hexagonal array. Each unit is a tileable circuit board, with a microprocessor, color-based object sensor and servo-actuated biomimetic cilia actuator. Localized synchronous communication between cilia allowed for the emergence of coordinated action, moving different colored objects together. The coordinated beating action was capable of moving objects up to 4 cm/s at its highest beating frequency; however, objects were moved at a speed proportional to the beat frequency. Using the local communication, we were able to detect the shape of objects and rotating an object using edge detection was performed; however, lateral manipulation using shape information was unsuccessful.

Concurrent Collections (CnC): A new approach to parallel programming

CERN Multimedia

CERN. Geneva

2010-01-01

A common approach in designing parallel languages is to provide some high level handles to manipulate the use of the parallel platform. This exposes some aspects of the target platform, for example, shared vs. distributed memory. It may expose some but not all types of parallelism, for example, data parallelism but not task parallelism. This approach must find a balance between the desire to provide a simple view for the domain expert and provide sufficient power for tuning. This is hard for any given architecture and harder if the language is to apply to a range of architectures. Either simplicity or power is lost. Instead of viewing the language design problem as one of providing the programmer with high level handles, we view the problem as one of designing an interface. On one side of this interface is the programmer (domain expert) who knows the application but needs no knowledge of any aspects of the platform. On the other side of the interface is the performance expert (programmer o...

BCYCLIC: A parallel block tridiagonal matrix cyclic solver

Science.gov (United States)

Hirshman, S. P.; Perumalla, K. S.; Lynch, V. E.; Sanchez, R.

2010-09-01

A block tridiagonal matrix is factored with minimal fill-in using a cyclic reduction algorithm that is easily parallelized. Storage of the factored blocks allows the application of the inverse to multiple right-hand sides which may not be known at factorization time. Scalability with the number of block rows is achieved with cyclic reduction, while scalability with the block size is achieved using multithreaded routines (OpenMP, GotoBLAS) for block matrix manipulation. This dual scalability is a noteworthy feature of this new solver, as well as its ability to efficiently handle arbitrary (non-powers-of-2) block row and processor numbers. Comparison with a state-of-the art parallel sparse solver is presented. It is expected that this new solver will allow many physical applications to optimally use the parallel resources on current supercomputers. Example usage of the solver in magneto-hydrodynamic (MHD), three-dimensional equilibrium solvers for high-temperature fusion plasmas is cited.

Augmented reality as a tool for linguistic research: Intercepting and manipulating multimodal interaction

OpenAIRE

Pitsch, Karola; Neumann, Alexander; Schnier, Christian; Hermann, Thomas

2013-01-01

We suggest that an Augmented Reality (AR) system for coupled interaction partners provides a new tool for linguistic research that allows to manipulate the coparticipants’ real-time perception and action. It encompasses novel facilities for recording heterogeneous sensor-rich data sets to be accessed in parallel with qualitative/manual and quantitative/computational methods.

Synthesis and Evaluation of A High Precision 3D-Printed Ti6Al4V Compliant Parallel Manipulator

Science.gov (United States)

Pham, Minh Tuan; Teo, Tat Joo; Huat Yeo, Song; Wang, Pan; Nai, Mui Ling Sharon

2017-12-01

A novel 3D printed compliant parallel manipulator (CPM) with θX - θX - Z motions is presented in this paper. This CPM is synthesized using the beam-based method, a new structural optimization approach, to achieve optimized stiffness properties with targeted dynamic behavior. The CPM performs high non-actuating stiffness based on the predicted stiffness ratios of about 3600 for translations and 570 for rotations, while the dynamic response is fast with the targeted first resonant mode of 100Hz. A prototype of the synthesized CPM is fabricated using the electron beam melting (EBM) technology with Ti6Al4V material. Driven by three voice-coil (VC) motors, the CPM demonstrated a positioning resolution of 50nm along the Z axis and an angular resolution of ~0.3 “about the X and Y axes, the positioning accuracy is also good with the measured values of ±25.2nm and ±0.17” for the translation and rotations respectively. Experimental investigation also shows that this large workspace CPM has a first resonant mode of 98Hz and the stiffness behavior matches the prediction with the highest deviation of 11.2%. Most importantly, the full workspace of 10° × 10° × 7mm of the proposed CPM can be achieved, that demonstrates 3D printed compliant mechanisms can perform large elastic deformation. The obtained results show that CPMs printed by EBM technology have predictable mechanical characteristics and are applicable in precise positioning systems.

Integrated Task And Data Parallel Programming: Language Design

Science.gov (United States)

Grimshaw, Andrew S.; West, Emily A.

1998-01-01

his research investigates the combination of task and data parallel language constructs within a single programming language. There are an number of applications that exhibit properties which would be well served by such an integrated language. Examples include global climate models, aircraft design problems, and multidisciplinary design optimization problems. Our approach incorporates data parallel language constructs into an existing, object oriented, task parallel language. The language will support creation and manipulation of parallel classes and objects of both types (task parallel and data parallel). Ultimately, the language will allow data parallel and task parallel classes to be used either as building blocks or managers of parallel objects of either type, thus allowing the development of single and multi-paradigm parallel applications. 1995 Research Accomplishments In February I presented a paper at Frontiers '95 describing the design of the data parallel language subset. During the spring I wrote and defended my dissertation proposal. Since that time I have developed a runtime model for the language subset. I have begun implementing the model and hand-coding simple examples which demonstrate the language subset. I have identified an astrophysical fluid flow application which will validate the data parallel language subset. 1996 Research Agenda Milestones for the coming year include implementing a significant portion of the data parallel language subset over the Legion system. Using simple hand-coded methods, I plan to demonstrate (1) concurrent task and data parallel objects and (2) task parallel objects managing both task and data parallel objects. My next steps will focus on constructing a compiler and implementing the fluid flow application with the language. Concurrently, I will conduct a search for a real-world application exhibiting both task and data parallelism within the same program m. Additional 1995 Activities During the fall I collaborated

Hardware and software and machine-tool simulation with parallel structures mechanisms

Directory of Open Access Journals (Sweden)

Keba P.V.

2016-12-01

Full Text Available The usage spectrum of mechanisms with parallel structure is spreading all the time. The mechanisms of machine-tools and manipulators become more complicated and it is necessary to improve the program-controlled modules. Closed circuit mechanisms are mostly spread in robotic complexes, where manipulator performs complicated spatial movements by the given trajectory. The usage spectrum is very wide and the most popular are sorting, welding, assembling and others. However, the problem of designing the operating programs is still present even today. It is just because the developed post-processors are created for the equipment that we have for now. But new machine tool constructions appear every day and there is a necessity to control them. The problems associated with using of hardware and software of mechanisms with parallel structure in computer-aided simulation are considered. The program for inverse problem kinematics solving is designed. New method of designing the control programs is found. The kinematic analysis methods options and calculated data obtained by computer mathematics systems are shown with «Tools Glide» software taken as an example.

3D printed soft parallel actuator

Science.gov (United States)

Zolfagharian, Ali; Kouzani, Abbas Z.; Khoo, Sui Yang; Noshadi, Amin; Kaynak, Akif

2018-04-01

This paper presents a 3-dimensional (3D) printed soft parallel contactless actuator for the first time. The actuator involves an electro-responsive parallel mechanism made of two segments namely active chain and passive chain both 3D printed. The active chain is attached to the ground from one end and constitutes two actuator links made of responsive hydrogel. The passive chain, on the other hand, is attached to the active chain from one end and consists of two rigid links made of polymer. The actuator links are printed using an extrusion-based 3D-Bioplotter with polyelectrolyte hydrogel as printer ink. The rigid links are also printed by a 3D fused deposition modelling (FDM) printer with acrylonitrile butadiene styrene (ABS) as print material. The kinematics model of the soft parallel actuator is derived via transformation matrices notations to simulate and determine the workspace of the actuator. The printed soft parallel actuator is then immersed into NaOH solution with specific voltage applied to it via two contactless electrodes. The experimental data is then collected and used to develop a parametric model to estimate the end-effector position and regulate kinematics model in response to specific input voltage over time. It is observed that the electroactive actuator demonstrates expected behaviour according to the simulation of its kinematics model. The use of 3D printing for the fabrication of parallel soft actuators opens a new chapter in manufacturing sophisticated soft actuators with high dexterity and mechanical robustness for biomedical applications such as cell manipulation and drug release.

Acoustic manipulation of bacteria cells suspensions

Science.gov (United States)

GutiéRrez-Ramos, Salomé; Hoyos, Mauricio; Aider, Jean Luc; Ruiz, Carlos; Acoustofluidics Team Team; Soft; Bio Group Collaboration

An acoustic contacless manipulation gives advantages in the exploration of the complex dynamics enviroment that active matter exhibits. Our works reports the control confinement and dispersion of Escherichia coliRP437-pZA3R-YFP suspensions (M9Glu-Ca) via acoustic levitation.The manipulation of the bacteria bath in a parallel plate resonator is achieved using the acoustic radiation force and the secondary radiation force. The primary radiation force generates levitation of the bacteria cells at the nodal plane of the ultrasonic standing wave generated inside the resonator. On the other side, secondary forces leads to the consolidation of stable aggregates. All the experiments were performed in the acoustic trap described, where we excite the emission plate with a continuous sinusoidal signal at a frequency in the order of MHz and a quartz slide as the reflector plate. In a typical experiment we observed that, before the input of the signal, the bacteria cells exhibit their typical run and tumble behavior and after the sound is turned on all of them displace towards the nodal plane, and instantaneously the aggregation begins in this region. CNRS French National Space Studies, CONACYT Mexico.

9th Asian Conference on Computer-Aided Surgery

CERN Document Server

2016-01-01

This book presents the latest research advances in the theory, design, control, and application of robot systems intended for a variety of purposes such as manipulation, manufacturing, automation, surgery, locomotion, and biomechanics. Several chapters deal with fundamental kinematics in nature, including synthesis, calibration, redundancy, force control, dexterity, inverse and forward kinematics, kinematic singularities, and over-constrained systems. This book is a compilation of the extended versions of the very best papers selected from the many that were presented at the Asian Conference on Computer-Aided Surgery held September 16–18, 2013, in Tokyo, Japan (ACCAS 2013).

Parallel PDE-Based Simulations Using the Common Component Architecture

International Nuclear Information System (INIS)

McInnes, Lois C.; Allan, Benjamin A.; Armstrong, Robert; Benson, Steven J.; Bernholdt, David E.; Dahlgren, Tamara L.; Diachin, Lori; Krishnan, Manoj Kumar; Kohl, James A.; Larson, J. Walter; Lefantzi, Sophia; Nieplocha, Jarek; Norris, Boyana; Parker, Steven G.; Ray, Jaideep; Zhou, Shujia

2006-01-01

The complexity of parallel PDE-based simulations continues to increase as multimodel, multiphysics, and multi-institutional projects become widespread. A goal of component based software engineering in such large-scale simulations is to help manage this complexity by enabling better interoperability among various codes that have been independently developed by different groups. The Common Component Architecture (CCA) Forum is defining a component architecture specification to address the challenges of high-performance scientific computing. In addition, several execution frameworks, supporting infrastructure, and general purpose components are being developed. Furthermore, this group is collaborating with others in the high-performance computing community to design suites of domain-specific component interface specifications and underlying implementations. This chapter discusses recent work on leveraging these CCA efforts in parallel PDE-based simulations involving accelerator design, climate modeling, combustion, and accidental fires and explosions. We explain how component technology helps to address the different challenges posed by each of these applications, and we highlight how component interfaces built on existing parallel toolkits facilitate the reuse of software for parallel mesh manipulation, discretization, linear algebra, integration, optimization, and parallel data redistribution. We also present performance data to demonstrate the suitability of this approach, and we discuss strategies for applying component technologies to both new and existing applications

Stiffness analysis and comparison of a Biglide parallel grinder with alternative spatial modular parallelograms

DEFF Research Database (Denmark)

Wu, Guanglei; Zou, Ping

2017-01-01

This paper deals with the stiffness modeling, analysis and comparison of a Biglide parallel grinder with two alternative modular parallelograms. It turns out that the Cartesian stiffness matrix of the manipulator has the property that it can be decoupled into two homogeneous matrices, correspondi...

Mathematical Abstraction: Constructing Concept of Parallel Coordinates

Science.gov (United States)

Nurhasanah, F.; Kusumah, Y. S.; Sabandar, J.; Suryadi, D.

2017-09-01

Mathematical abstraction is an important process in teaching and learning mathematics so pre-service mathematics teachers need to understand and experience this process. One of the theoretical-methodological frameworks for studying this process is Abstraction in Context (AiC). Based on this framework, abstraction process comprises of observable epistemic actions, Recognition, Building-With, Construction, and Consolidation called as RBC + C model. This study investigates and analyzes how pre-service mathematics teachers constructed and consolidated concept of Parallel Coordinates in a group discussion. It uses AiC framework for analyzing mathematical abstraction of a group of pre-service teachers consisted of four students in learning Parallel Coordinates concepts. The data were collected through video recording, students’ worksheet, test, and field notes. The result shows that the students’ prior knowledge related to concept of the Cartesian coordinate has significant role in the process of constructing Parallel Coordinates concept as a new knowledge. The consolidation process is influenced by the social interaction between group members. The abstraction process taken place in this group were dominated by empirical abstraction that emphasizes on the aspect of identifying characteristic of manipulated or imagined object during the process of recognizing and building-with.

Efficient illumination of spatial light modulators for optical trapping and manipulation

DEFF Research Database (Denmark)

Bañas, Andrew Rafael; Kopylov, Oleksii; Raaby, Peter

Energy efficiency is always desirable. This is particularly true with lasers that find many applications in research and industry. Combined with spatial light modulators (SLMs) lasers are used for optical trapping and manipulation, sorting, microscopy or biological stimulation1. Besides efficiency....... We have also shown dynamic SLM-generated patterns for materials processing and biological research. To efficiently illuminate an SLM, we used a compact pen-sized GPC-LS in place of an iris. For the same input power, hologram reconstructions are ~3x brighter or alternatively ~3x more focal spots can...... be addressed. This allows better response or increased parallel addressing for e.g. optical manipulation and sorting. Simple yet effective, a GPC-LS could save substantial power in applications that truncate lasers to a specific shape....

Manipulators

International Nuclear Information System (INIS)

Wilcock, P.D.

1984-01-01

The patent concerns a manipulator, which enables operations to be carried out remotely from the operator. The device is suitable for use in handling of radioactive materials and other hazardous liquids or gases. The specifications are given, and the movements of the manipulator arm described. (U.K.)

Design of parallel intersector weld/cut robot for machining processes in ITER vacuum vessel

International Nuclear Information System (INIS)

Wu Huapeng; Handroos, Heikki; Kovanen, Janne; Rouvinen, Asko; Hannukainen, Petri; Saira, Tanja; Jones, Lawrence

2003-01-01

This paper presents a new parallel robot Penta-WH, which has five degrees of freedom driven by hydraulic cylinders. The manipulator has a large, singularity-free workspace and high stiffness and it acts as a transport device for welding, machining and inspection end-effectors inside the ITER vacuum vessel. The presented kinematic structure of a parallel robot is particularly suitable for the ITER environment. Analysis of the machining process for ITER, such as the machining methods and forces are given, and the kinematic analyses, such as workspace and force capacity are discussed

The cost of conservative synchronization in parallel discrete event simulations

Science.gov (United States)

Nicol, David M.

1990-01-01

The performance of a synchronous conservative parallel discrete-event simulation protocol is analyzed. The class of simulation models considered is oriented around a physical domain and possesses a limited ability to predict future behavior. A stochastic model is used to show that as the volume of simulation activity in the model increases relative to a fixed architecture, the complexity of the average per-event overhead due to synchronization, event list manipulation, lookahead calculations, and processor idle time approach the complexity of the average per-event overhead of a serial simulation. The method is therefore within a constant factor of optimal. The analysis demonstrates that on large problems--those for which parallel processing is ideally suited--there is often enough parallel workload so that processors are not usually idle. The viability of the method is also demonstrated empirically, showing how good performance is achieved on large problems using a thirty-two node Intel iPSC/2 distributed memory multiprocessor.

Fundamental study on laser manipulation of contamination particles with determining shape, size and species

International Nuclear Information System (INIS)

Shimizu, Isao; Fujii, Taketsugu

1995-01-01

It has been desired to eliminate or collect the contamination particles of radioisotope in each sort of species or shape and size non-invasively. The shape and size of particle can be determined from the shape and distribution of diffraction pattern of particle in the parallel laser beam, the species of particle can be discriminated by the fluorescence from resonance of laser beam, or by the laser Raman scattering, and the particle suspended in the air or falling down in a vacuum can be levitated against the gravity and trapped by the radiation force and the trapping force of the focussed laser beam in the atmosphere or in a vacuum. For the purpose of the non-invasive manipulation of contamination particles, the laser manipulation technique, image processing technique with Multiplexed Matched Spatial Filter and the determination technique of laser Raman scattering or fluorescence from resonance of laser light were combined in the experiments. The shape, size and species of particles trapped in the focal plane of focused Ar laser beam can be determined simultaneously and instantaneously from the shape and intensity distributions of diffraction patterns of the particles in the irradiation of parallel coherent beam of He-Ne laser, and fluorescence from the resonance of YAG laser beam with variable wave length. In this research, a new technique is proposed to manipulate non-invasively the contamination particles determined with the shape, size and species in the atmosphere or in a vacuum, by laser beam. (author)

Fast robot kinematics modeling by using a parallel simulator (PSIM)

International Nuclear Information System (INIS)

El-Gazzar, H.M.; Ayad, N.M.A.

2002-01-01

High-speed computers are strongly needed not only for solving scientific and engineering problems, but also for numerous industrial applications. Such applications include computer-aided design, oil exploration, weather predication, space applications and safety of nuclear reactors. The rapid development in VLSI technology makes it possible to implement time consuming algorithms in real-time situations. Parallel processing approaches can now be used to reduce the processing-time for models of very high mathematical structure such as the kinematics molding of robot manipulator. This system is used to construct and evaluate the performance and cost effectiveness of several proposed methods to solve the Jacobian algorithm. Parallelism is introduced to the algorithms by using different task-allocations and dividing the whole job into sub tasks. Detailed analysis is performed and results are obtained for the case of six DOF (degree of freedom) robot arms (Stanford Arm). Execution times comparisons between Von Neumann (uni processor) and parallel processor architectures by using parallel simulator package (PSIM) are presented. The gained results are much in favour for the parallel techniques by at least fifty-percent improvements. Of course, further studies are needed to achieve the convenient and optimum number of processors has to be done

Fast robot kinematics modeling by using a parallel simulator (PSIM)

Energy Technology Data Exchange (ETDEWEB)

El-Gazzar, H M; Ayad, N M.A. [Atomic Energy Authority, Reactor Dept., Computer and Control Lab., P.O. Box no 13759 (Egypt)

2002-09-15

High-speed computers are strongly needed not only for solving scientific and engineering problems, but also for numerous industrial applications. Such applications include computer-aided design, oil exploration, weather predication, space applications and safety of nuclear reactors. The rapid development in VLSI technology makes it possible to implement time consuming algorithms in real-time situations. Parallel processing approaches can now be used to reduce the processing-time for models of very high mathematical structure such as the kinematics molding of robot manipulator. This system is used to construct and evaluate the performance and cost effectiveness of several proposed methods to solve the Jacobian algorithm. Parallelism is introduced to the algorithms by using different task-allocations and dividing the whole job into sub tasks. Detailed analysis is performed and results are obtained for the case of six DOF (degree of freedom) robot arms (Stanford Arm). Execution times comparisons between Von Neumann (uni processor) and parallel processor architectures by using parallel simulator package (PSIM) are presented. The gained results are much in favour for the parallel techniques by at least fifty-percent improvements. Of course, further studies are needed to achieve the convenient and optimum number of processors has to be done.

Manipulator for inspection or repair of heat exchanger tubes, in particular in steam generators for nuclear reactors

International Nuclear Information System (INIS)

Gugel, G.

1979-01-01

The manipulator used to inspect or repair pipes in the steam generator chamber of a PWR can be introduced and removed through a penetration nozzle which can be sealed tightly by means of a blind flange. The front end of the manipulator carries a swivel arm which can be operated remotely to be moved in a plane parallel to the tube plate. The end of the swivel arm carries a holder for a mouthpiece which can be extended and retracted. This carrier can also be operated remotely so as to be aligned to the pipe orifices in a direction normal to the swivel plane of the swivel arm. The manipulator is supported in antifriction bearings in the penetration nozzle so as to be movable longitudinally. (DG) [de

Design and real-time control of a robotic system for fracture manipulation.

Science.gov (United States)

Dagnino, G; Georgilas, I; Tarassoli, P; Atkins, R; Dogramadzi, S

2015-08-01

This paper presents the design, development and control of a new robotic system for fracture manipulation. The objective is to improve the precision, ergonomics and safety of the traditional surgical procedure to treat joint fractures. The achievements toward this direction are here reported and include the design, the real-time control architecture and the evaluation of a new robotic manipulator system. The robotic manipulator is a 6-DOF parallel robot with the struts developed as linear actuators. The control architecture is also described here. The high-level controller implements a host-target structure composed by a host computer (PC), a real-time controller, and an FPGA. A graphical user interface was designed allowing the surgeon to comfortably automate and monitor the robotic system. The real-time controller guarantees the determinism of the control algorithms adding an extra level of safety for the robotic automation. The system's positioning accuracy and repeatability have been demonstrated showing a maximum positioning RMSE of 1.18 ± 1.14mm (translations) and 1.85 ± 1.54° (rotations).

Highly controllable near-surface swimming of magnetic Janus nanorods: application to payload capture and manipulation

International Nuclear Information System (INIS)

Mair, Lamar O; Carpenter, Jerome; Evans, Benjamin; Hall, Adam R; Shields, Adam; Superfine, Richard; Ford, Kris; Millard, Michael

2011-01-01

Directed manipulation of nanomaterials has significant implications in the field of nanorobotics, nanobiotechnology, microfluidics and directed assembly. With the goal of highly controllable nanomaterial manipulation in mind, we present a technique for the near-surface manoeuvering of magnetic nanorod swimmers and its application to controlled micromanipulation. We fabricate magnetic Janus nanorods and show that the magnetic rotation of these nanorods near a floor results in predictable translational motion. The nanorod plane of rotation is nearly parallel to the floor, the angle between rod tilt and floor being expressed by θ, where 0 0 0 . Orthogonal magnetic fields control in-plane motion arbitrarily. Our model for translation incorporates symmetry breaking through increased drag at the no-slip surface boundary. Using this method we demonstrate considerable rod steerability. Additionally, we approach, capture, and manipulate a polystyrene microbead as proof of principle. We attach Janus nanorods to the surfaces of cells and utilize these rods to manipulate individual cells, proving the ability to manoeuver payloads with a wide range of sizes.

An Approach Using Parallel Architecture to Storage DICOM Images in Distributed File System

International Nuclear Information System (INIS)

Soares, Tiago S; Prado, Thiago C; Dantas, M A R; De Macedo, Douglas D J; Bauer, Michael A

2012-01-01

Telemedicine is a very important area in medical field that is expanding daily motivated by many researchers interested in improving medical applications. In Brazil was started in 2005, in the State of Santa Catarina has a developed server called the CyclopsDCMServer, which the purpose to embrace the HDF for the manipulation of medical images (DICOM) using a distributed file system. Since then, many researches were initiated in order to seek better performance. Our approach for this server represents an additional parallel implementation in I/O operations since HDF version 5 has an essential feature for our work which supports parallel I/O, based upon the MPI paradigm. Early experiments using four parallel nodes, provide good performance when compare to the serial HDF implemented in the CyclopsDCMServer.

Generalized framework for the parallel semantic segmentation of multiple objects and posterior manipulation

DEFF Research Database (Denmark)

Llopart, Adrian; Ravn, Ole; Andersen, Nils Axel

2017-01-01

The end-to-end approach presented in this paper deals with the recognition, detection, segmentation and grasping of objects, assuming no prior knowledge of the environment nor objects. The proposed pipeline is as follows: 1) Usage of a trained Convolutional Neural Net (CNN) that recognizes up to 80...... different classes of objects in real time and generates bounding boxes around them. 2) An algorithm to derive in parallel the pointclouds of said regions of interest (ROI). 3) Eight different segmentation methods to remove background data and noise from the pointclouds and obtain a precise result...

Parallel constraint satisfaction in memory-based decisions.

Science.gov (United States)

Glöckner, Andreas; Hodges, Sara D

2011-01-01

Three studies sought to investigate decision strategies in memory-based decisions and to test the predictions of the parallel constraint satisfaction (PCS) model for decision making (Glöckner & Betsch, 2008). Time pressure was manipulated and the model was compared against simple heuristics (take the best and equal weight) and a weighted additive strategy. From PCS we predicted that fast intuitive decision making is based on compensatory information integration and that decision time increases and confidence decreases with increasing inconsistency in the decision task. In line with these predictions we observed a predominant usage of compensatory strategies under all time-pressure conditions and even with decision times as short as 1.7 s. For a substantial number of participants, choices and decision times were best explained by PCS, but there was also evidence for use of simple heuristics. The time-pressure manipulation did not significantly affect decision strategies. Overall, the results highlight intuitive, automatic processes in decision making and support the idea that human information-processing capabilities are less severely bounded than often assumed.

Currency Manipulation versus Current Account Manipulation

OpenAIRE

Junning Cai

2005-01-01

It is said that a country’s currency peg can become currency manipulation representing protracted government intervention in the foreign exchange market that gives it unfair competitive advantage in international trade yet prevents effective balance of payments in its trade partners. Regarding this widespread fallacy, this paper explains why currency peg is not currency manipulation even when it keeps a country’s currency undervalued. We clarify that 1) government is inherently a major player...

Cable-driven elastic parallel humanoid head with face tracking for Autism Spectrum Disorder interventions.

Science.gov (United States)

Su, Hao; Dickstein-Fischer, Laurie; Harrington, Kevin; Fu, Qiushi; Lu, Weina; Huang, Haibo; Cole, Gregory; Fischer, Gregory S

2010-01-01

This paper presents the development of new prismatic actuation approach and its application in human-safe humanoid head design. To reduce actuator output impedance and mitigate unexpected external shock, the prismatic actuation method uses cables to drive a piston with preloaded spring. By leveraging the advantages of parallel manipulator and cable-driven mechanism, the developed neck has a parallel manipulator embodiment with two cable-driven limbs embedded with preloaded springs and one passive limb. The eye mechanism is adapted for low-cost webcam with succinct "ball-in-socket" structure. Based on human head anatomy and biomimetics, the neck has 3 degree of freedom (DOF) motion: pan, tilt and one decoupled roll while each eye has independent pan and synchronous tilt motion (3 DOF eyes). A Kalman filter based face tracking algorithm is implemented to interact with the human. This neck and eye structure is translatable to other human-safe humanoid robots. The robot's appearance reflects a non-threatening image of a penguin, which can be translated into a possible therapeutic intervention for children with Autism Spectrum Disorders.

Dexterous Manipulation: Making Remote Manipulators Easy to Use

International Nuclear Information System (INIS)

HARRIGAN, RAYMOND W.; BENNETT, PHIL C.

2001-01-01

Perhaps the most basic barrier to the widespread deployment of remote manipulators is that they are very difficult to use. Remote manual operations are fatiguing and tedious, while fully autonomous systems are seldom able to function in changing and unstructured environments. An alternative approach to these extremes is to exploit computer control while leaving the operator in the loop to take advantage of the operator's perceptual and decision-making capabilities. This report describes research that is enabling gradual introduction of computer control and decision making into operator-supervised robotic manipulation systems, and its integration on a commercially available, manually controlled mobile manipulator

The age of enlightenment: evolving opportunities in brain research through optical manipulation of neuronal activity

Directory of Open Access Journals (Sweden)

Jason eJerome

2011-12-01

Full Text Available Optical manipulation of neuronal activity has rapidly developed into the most powerful and widely used approach to study mechanisms related to neuronal connectivity over a range of scales. Since the early use of single site uncaging to map network connectivity, rapid technological development of light modulation techniques has added important new options, such as fast scanning photostimulation, massively parallel control of light stimuli, holographic uncaging and 2-photon stimulation techniques. Exciting new developments in optogenetics complement neurotransmitter uncaging techniques by providing cell-type specificity and in vivo usability, providing optical access to the neural substrates of behavior. Here we review the rapid evolution of methods for the optical manipulation of neuronal activity, emphasizing crucial recent developments.

The age of enlightenment: evolving opportunities in brain research through optical manipulation of neuronal activity.

Science.gov (United States)

Jerome, Jason; Heck, Detlef H

2011-01-01

Optical manipulation of neuronal activity has rapidly developed into the most powerful and widely used approach to study mechanisms related to neuronal connectivity over a range of scales. Since the early use of single site uncaging to map network connectivity, rapid technological development of light modulation techniques has added important new options, such as fast scanning photostimulation, massively parallel control of light stimuli, holographic uncaging, and two-photon stimulation techniques. Exciting new developments in optogenetics complement neurotransmitter uncaging techniques by providing cell-type specificity and in vivo usability, providing optical access to the neural substrates of behavior. Here we review the rapid evolution of methods for the optical manipulation of neuronal activity, emphasizing crucial recent developments.

Effects of parallel planning on agreement production.

Science.gov (United States)

Veenstra, Alma; Meyer, Antje S; Acheson, Daniel J

2015-11-01

An important issue in current psycholinguistics is how the time course of utterance planning affects the generation of grammatical structures. The current study investigated the influence of parallel activation of the components of complex noun phrases on the generation of subject-verb agreement. Specifically, the lexical interference account (Gillespie & Pearlmutter, 2011b; Solomon & Pearlmutter, 2004) predicts more agreement errors (i.e., attraction) for subject phrases in which the head and local noun mismatch in number (e.g., the apple next to the pears) when nouns are planned in parallel than when they are planned in sequence. We used a speeded picture description task that yielded sentences such as the apple next to the pears is red. The objects mentioned in the noun phrase were either semantically related or unrelated. To induce agreement errors, pictures sometimes mismatched in number. In order to manipulate the likelihood of parallel processing of the objects and to test the hypothesized relationship between parallel processing and the rate of agreement errors, the pictures were either placed close together or far apart. Analyses of the participants' eye movements and speech onset latencies indicated slower processing of the first object and stronger interference from the related (compared to the unrelated) second object in the close than in the far condition. Analyses of the agreement errors yielded an attraction effect, with more errors in mismatching than in matching conditions. However, the magnitude of the attraction effect did not differ across the close and far conditions. Thus, spatial proximity encouraged parallel processing of the pictures, which led to interference of the associated conceptual and/or lexical representation, but, contrary to the prediction, it did not lead to more attraction errors. Copyright © 2015 Elsevier B.V. All rights reserved.

A review of microfabrication techniques and dielectrophoretic microdevices for particle manipulation and separation

International Nuclear Information System (INIS)

Li, M; Li, W H; Zhang, J; Alici, G; Wen, W

2014-01-01

The development of lab-on-a-chip (LOC) devices over the past decade has attracted growing interest. LOC devices aim to achieve the miniaturization, integration, automation and parallelization of biological and chemical assays. One of the applications, the ability to effectively and accurately manipulate and separate micro- and nano-scale particles in an aqueous solution, is particularly appealing in biological, chemical and medical fields. Among the technologies that have been developed and implemented in microfluidic microsystems for particle manipulation and separation (such as mechanical, inertial, hydrodynamic, acoustic, optical, magnetic and electrical methodologies), dielectrophoresis (DEP) may prove to be the most popular because of its label-free nature, ability to manipulate neutral bioparticles, analyse with high selectivity and sensitivity, compatibility with LOC devices, and easy and direct interface with electronics. The required spatial electric non-uniformities for the DEP effect can be generated by patterning microelectrode arrays within microchannels, or placing insulating obstacles within a microchannel and curving the microchannels. A wide variety of electrode- and insulator-based DEP microdevices have been developed, fabricated, and successfully employed to manipulate and separate bioparticles (i.e. DNA, proteins, bacteria, viruses, mammalian and yeast cells). This review provides an overview of the state-of-the-art of microfabrication techniques and of the structures of dielectrophoretic microdevices aimed towards different applications. The techniques used for particle manipulation and separation based on microfluidics are provided in this paper. In addition, we also present the theoretical background of DEP. (topical review)

A manipulator

International Nuclear Information System (INIS)

Cole, G.V.; Hofmann, D.A.; Ashby, R.

1984-01-01

A manipulator is described, for remote handling of objects within an enclosure, by an operator outside the enclosure. The manipulator consists of a telescopically extensible arm member, the action of which is controlled by a motor-driven lead screw. (U.K.)

Intelligent spatial ecosystem modeling using parallel processors

International Nuclear Information System (INIS)

Maxwell, T.; Costanza, R.

1993-01-01

Spatial modeling of ecosystems is essential if one's modeling goals include developing a relatively realistic description of past behavior and predictions of the impacts of alternative management policies on future ecosystem behavior. Development of these models has been limited in the past by the large amount of input data required and the difficulty of even large mainframe serial computers in dealing with large spatial arrays. These two limitations have begun to erode with the increasing availability of remote sensing data and GIS systems to manipulate it, and the development of parallel computer systems which allow computation of large, complex, spatial arrays. Although many forms of dynamic spatial modeling are highly amenable to parallel processing, the primary focus in this project is on process-based landscape models. These models simulate spatial structure by first compartmentalizing the landscape into some geometric design and then describing flows within compartments and spatial processes between compartments according to location-specific algorithms. The authors are currently building and running parallel spatial models at the regional scale for the Patuxent River region in Maryland, the Everglades in Florida, and Barataria Basin in Louisiana. The authors are also planning a project to construct a series of spatially explicit linked ecological and economic simulation models aimed at assessing the long-term potential impacts of global climate change

Remote inspection manipulators for AGR II: Babcock Power's interstitial manipulator

International Nuclear Information System (INIS)

Whyley, S.R.

1985-01-01

The interstitial manipulator has been designed and built by Babcock Power for the remote visual inspection of AGR II reactors at Heysham and Torness. Its five drives are operated from a console local to the manipulator on the pile cap, or from a similar console located remotely. The need to operate from an interstitial ISI standpipe has restricted the size of the components entering the reactor, and this has consequently provided the major design constraint. A detailed structural assessment of the manipulator was carried out to demonstrate the ability to operate with payloads in excess of the largest camera weight of 13.6 kg. The manipulator finite element model was also used to determine static deflections, and, as a consequence, has provided data from which the control system is able to predict accurately the camera's position. Other computer aided design techniques have enabled the step by step sequences of manipulator deployment, in the restricted space available, to be successfully demonstrated. (author)

Ion Trapping, Storage, and Ejection in Structures for Lossless Ion Manipulations.

Science.gov (United States)

Zhang, Xinyu; Garimella, Sandilya V B; Prost, Spencer A; Webb, Ian K; Chen, Tsung-Chi; Tang, Keqi; Tolmachev, Aleksey V; Norheim, Randolph V; Baker, Erin S; Anderson, Gordon A; Ibrahim, Yehia M; Smith, Richard D

2015-06-16

A new Structures for Lossless Ion Manipulations (SLIM) module, having electrode arrays patterned on a pair of parallel printed circuit boards (PCB), was constructed and utilized to investigate capabilities for ion trapping at a pressure of 4 Torr. Positive ions were confined by application of RF voltages to a series of inner rung electrodes with alternating phase on adjacent electrodes, in conjunction with positive DC potentials on surrounding guard electrodes on each PCB. An axial DC field was also introduced by stepwise varying the DC potentials applied to the inner rung electrodes to control the ion transport and accumulation inside the ion trapping region. We show that ions can be trapped and accumulated with up to 100% efficiency, stored for at least 5 h with no significant losses, and then could be rapidly ejected from the SLIM trap. The present results provide a foundation for the development of much more complex SLIM devices that facilitate extended ion manipulations.

A backtracking algorithm for the stream AND-parallel execution of logic programs

Energy Technology Data Exchange (ETDEWEB)

Somogyi, Z.; Ramamohanarao, K.; Vaghani, J. (Univ. of Melbourne, Parkville (Australia))

1988-06-01

The authors present the first backtracking algorithm for stream AND-parallel logic programs. It relies on compile-time knowledge of the data flow graph of each clause to let it figure out efficiently which goals to kill or restart when a goal fails. This crucial information, which they derive from mode declarations, was not available at compile-time in any previous stream AND-parallel system. They show that modes can increase the precision of the backtracking algorithm, though their algorithm allows this precision to be traded off against overhead on a procedure-by-procedure and call-by-call basis. The modes also allow their algorithm to handle efficiently programs that manipulate partially instantiated data structures and an important class of programs with circular dependency graphs. On code that does not need backtracking, the efficiency of their algorithm approaches that of the committed-choice languages; on code that does need backtracking its overhead is comparable to that of the independent AND-parallel backtracking algorithms.

Manipulators in teleoperation

International Nuclear Information System (INIS)

Hamel, W.R.

1985-01-01

Teleoperated manipulators represent a mature technology which has evolved over nearly 40 years of applications experience. The wide range of manipulator concepts developed thus far reflect differing applications, priorities, and philosophies. The technology of teleoperated manipulators is in a rapid state of change (just as are industrial robotics) fueled by microelectronics and materials advances. Large strides in performance and dexterity are now practical and advantageous. Even though improved controls and sensory feedback will increase functionality, overall costs should be reduced as manipulator fabrication and assembly labor costs are reduced through improved manufacturing technology. As these advances begin to materialize, broader applications in nonnuclear areas should occur

Characteristics of manipulative in mathematics laboratory

Science.gov (United States)

Istiandaru, A.; Istihapsari, V.; Prahmana, R. C. I.; Setyawan, F.; Hendroanto, A.

2017-12-01

A manipulative is a teaching aid designed such that students could understand mathematical concepts by manipulating it. This article aims to provide an insight to the characteristics of manipulatives produced in the mathematics laboratory of Universitas Ahmad Dahlan, Indonesia. A case study was conducted to observe the existing manipulatives produced during the latest three years and classified the manipulatives based on the characteristics found. There are four kinds of manipulatives: constructivism manipulative, virtual manipulative, informative manipulative, and game-based manipulative. Each kinds of manipulative has different characteristics and impact towards the mathematics learning.

The Age of Enlightenment: Evolving Opportunities in Brain Research Through Optical Manipulation of Neuronal Activity

OpenAIRE

Jerome, Jason; Heck, Detlef H.

2011-01-01

Optical manipulation of neuronal activity has rapidly developed into the most powerful and widely used approach to study mechanisms related to neuronal connectivity over a range of scales. Since the early use of single site uncaging to map network connectivity, rapid technological development of light modulation techniques has added important new options, such as fast scanning photostimulation, massively parallel control of light stimuli, holographic uncaging, and two-photon stimulation techn...

Characterization of robotics parallel algorithms and mapping onto a reconfigurable SIMD machine

Science.gov (United States)

Lee, C. S. G.; Lin, C. T.

1989-01-01

The kinematics, dynamics, Jacobian, and their corresponding inverse computations are six essential problems in the control of robot manipulators. Efficient parallel algorithms for these computations are discussed and analyzed. Their characteristics are identified and a scheme on the mapping of these algorithms to a reconfigurable parallel architecture is presented. Based on the characteristics including type of parallelism, degree of parallelism, uniformity of the operations, fundamental operations, data dependencies, and communication requirement, it is shown that most of the algorithms for robotic computations possess highly regular properties and some common structures, especially the linear recursive structure. Moreover, they are well-suited to be implemented on a single-instruction-stream multiple-data-stream (SIMD) computer with reconfigurable interconnection network. The model of a reconfigurable dual network SIMD machine with internal direct feedback is introduced. A systematic procedure internal direct feedback is introduced. A systematic procedure to map these computations to the proposed machine is presented. A new scheduling problem for SIMD machines is investigated and a heuristic algorithm, called neighborhood scheduling, that reorders the processing sequence of subtasks to reduce the communication time is described. Mapping results of a benchmark algorithm are illustrated and discussed.

Manipulators for production and research

International Nuclear Information System (INIS)

Munro, Ian

1987-01-01

The development of caves or cells and master-slave manipulators to handle radioactive materials is discussed. Some of the most recent advances are described. A manipulator arm, a master-slave manipulator and a servomanipulator mounted on a manipulator are illustrated. Future developments are discussed - these include resolved tip control for the manipulator. (UK)

High accuracy microwave frequency measurement based on single-drive dual-parallel Mach-Zehnder modulator

DEFF Research Database (Denmark)

Zhao, Ying; Pang, Xiaodan; Deng, Lei

2011-01-01

A novel approach for broadband microwave frequency measurement by employing a single-drive dual-parallel Mach-Zehnder modulator is proposed and experimentally demonstrated. Based on bias manipulations of the modulator, conventional frequency-to-power mapping technique is developed by performing a...... 10−3 relative error. This high accuracy frequency measurement technique is a promising candidate for high-speed electronic warfare and defense applications....

Development master arm of 2-DOF planar parallel manipulator for In-Vitro Fertilization

Science.gov (United States)

Thamrongaphichartkul, Kitti; Vongbunyong, Supachai; Nuntakarn, Lalana

2018-01-01

Micromanipulator is a mechanical device used for manipulating miniature objects in the order of micron. It is widely used in In-Vitro Fertilization (IVF) in which sperms will be held in a micro-needle and penetrate to an oocyte for fertilization. IVF needs to be performed by high skill embryologists to control the movement of the needle accurately due to the lack of tactile perception of the user. Haptic device is a device that can transmit and simulate position, velocity and force in order to enhance interaction between the user and system. However, commercially available haptic devices have unnecessary degrees of freedom and limited workspace which are inappropriate for IVF process. This paper focuses on development of a haptic device for using in IVF process. It will be used as a master arm for the master-slave system for IVF process in order to enhance the ability of users to control the micromanipulator. As a result, the embryologist is able to carry out the IVF process more effectively with having tactile perception.

Hydraulic manipulator research at ORNL

International Nuclear Information System (INIS)

Kress, R.L.; Jansen, J.F.; Love, L.J.

1997-01-01

Recently, task requirements have dictated that manipulator payload capacity increase to accommodate greater payloads, greater manipulator length, and larger environmental interaction forces. General tasks such as waste storage tank cleanup and facility dismantlement and decommissioning require manipulator life capacities in the range of hundreds of pounds rather than tens of pounds. To meet the increased payload capacities demanded by present-day tasks, manipulator designers have turned once again to hydraulics as a means of actuation. In order to successfully design, build, and deploy a new hydraulic manipulator (or subsystem), sophisticated modeling, analysis, and control experiments are usually needed. Oak Ridge National Laboratory (ORNL) has a history of projects that incorporate hydraulics technology, including mobile robots, teleoperated manipulators, and full-scale construction equipment. In addition, to support the development and deployment of new hydraulic manipulators, ORNL has outfitted a significant experimental laboratory and has developed the software capability for research into hydraulic manipulators, hydraulic actuators, hydraulic systems, modeling of hydraulic systems, and hydraulic controls. The purpose of this article is to describe the past hydraulic manipulator developments and current hydraulic manipulator research capabilities at ORNL. Included are example experimental results from ORNL's flexible/prismatic test stand

Hydraulic manipulator research at ORNL

Energy Technology Data Exchange (ETDEWEB)

Kress, R.L.; Jansen, J.F. [Oak Ridge National Lab., TN (United States); Love, L.J. [Oak Ridge Inst. for Science and Education, TN (United States)

1997-03-01

Recently, task requirements have dictated that manipulator payload capacity increase to accommodate greater payloads, greater manipulator length, and larger environmental interaction forces. General tasks such as waste storage tank cleanup and facility dismantlement and decommissioning require manipulator life capacities in the range of hundreds of pounds rather than tens of pounds. To meet the increased payload capacities demanded by present-day tasks, manipulator designers have turned once again to hydraulics as a means of actuation. In order to successfully design, build, and deploy a new hydraulic manipulator (or subsystem), sophisticated modeling, analysis, and control experiments are usually needed. Oak Ridge National Laboratory (ORNL) has a history of projects that incorporate hydraulics technology, including mobile robots, teleoperated manipulators, and full-scale construction equipment. In addition, to support the development and deployment of new hydraulic manipulators, ORNL has outfitted a significant experimental laboratory and has developed the software capability for research into hydraulic manipulators, hydraulic actuators, hydraulic systems, modeling of hydraulic systems, and hydraulic controls. The purpose of this article is to describe the past hydraulic manipulator developments and current hydraulic manipulator research capabilities at ORNL. Included are example experimental results from ORNL`s flexible/prismatic test stand.

Analysis of gamma irradiator dose rate using spent fuel elements with parallel configuration

International Nuclear Information System (INIS)

Setiyanto; Pudjijanto MS; Ardani

2006-01-01

To enhance the utilization of the RSG-GAS reactor spent fuel, the gamma irradiator using spent fuel elements as a gamma source is a suitable choice. This irradiator can be used for food sterilization and preservation. The first step before realization, it is necessary to determine the gamma dose rate theoretically. The assessment was realized for parallel configuration fuel elements with the irradiation space can be placed between fuel element series. This analysis of parallel model was choice to compare with the circle model and as long as possible to get more space for irradiation and to do manipulation of irradiation target. Dose rate calculation were done with MCNP, while the estimation of gamma activities of fuel element was realized by OREGEN code with 1 year of average delay time. The calculation result show that the gamma dose rate of parallel model decreased up to 50% relatively compared with the circle model, but the value still enough for sterilization and preservation. Especially for food preservation, this parallel model give more flexible, while the gamma dose rate can be adjusted to the irradiation needed. The conclusion of this assessment showed that the utilization of reactor spent fuels for gamma irradiator with parallel model give more advantage the circle model. (author)

Manipulating objects by discrete excitable media coupled with contact-less actuator array: Open-loop case

International Nuclear Information System (INIS)

Skachek, Sergey; Adamatzky, Andrew; Melhuish, Chris

2005-01-01

A two-dimensional cellular automaton (CA) model of an excitable medium is coupled with an array of micro-actuators in the form of abstract air-jets. Each cell of the CA is linked to a unique air-jet. A cell state determines the orientation and intensity of the airflow generated by the air-jet corresponding to the cell. We explore the phenomenology of an open-loop configuration in which CA cells do not sense the presence of the object being moved. Excitation waves generated in the initial stimulation of the medium, travel on the lattice and cause waves of actuation in the air-jets, resulting in changing airflow patterns. Thus, the waves of actuation move and rotate the manipulated object. We study the manipulation of three convex shapes by excitable CA, and provide the classification of various types of object motion from straight to sinuous and oscillatory trajectories. The relation between the excitation dynamic and resulting trajectories of the object will be used in future designs of hardware prototypes of massive-parallel manipulators controlled by non-linear media

Advances in robot kinematics

CERN Document Server

Khatib, Oussama

2014-01-01

The topics addressed in this book cover the whole range of kinematic analysis, synthesis and design and consider robotic systems possessing serial, parallel and cable driven mechanisms. The robotic systems range from being less than fully mobile to kinematically redundant to overconstrained.  The fifty-six contributions report the latest results in robot kinematics with emphasis on emerging areas such as design and control of humanoids or humanoid subsystems. The book is of interest to researchers wanting to bring their knowledge up to date regarding modern topics in one of the basic disciplines in robotics, which relates to the essential property of robots, the motion of mechanisms.

Strategies for the AFM-based manipulation of silver nanowires on a flat surface

Science.gov (United States)

Liu, Hong-Zhi; Wu, Sen; Zhang, Jun-Ming; Bai, Hui-Tian; Jin, Fan; Pang, Hai; Hu, Xiao-Dong

2017-09-01

Silver nanowires (Ag NWs) are a promising material for building various sensors and devices at the nanoscale. However, the fast and precise placement of individual Ag NWs is still a challenge today. Atomic force microscopy (AFM) has been widely used to manipulate nanoparticles, yet this technology encounters many difficulties when being applied to the movement of Ag NWs as well as other soft one-dimensional (1D) materials, since the samples are easily distorted or even broken due to friction and adhesion on the substrate. In this paper, two novel manipulation strategies based on the parallel pushing method are presented. This method applies a group of short parallel pushing vectors (PPVs) to the Ag NW along its longitudinal direction. Identical and proportional vectors are respectively proposed to translate and rotate the Ag NWs with a straight-line configuration. The rotation strategy is also applied to straighten flexed Ag NWs. The finite element method simulation is introduced to analyse the behaviour of the Ag NWs as well as to optimize the parameter setting of the PPVs. Experiments are carried out to confirm the efficiency of the presented strategies. By comprehensive application of the new strategies, four Ag NWs are continuously assembled in a rectangular pattern. This study improves the controllability of the position and configuration of Ag NWs on a flat substrate. It also indicates the practicability of automatic nanofabrication using common AFMs.

Realization of cantilever arrays for parallel proximity imaging

International Nuclear Information System (INIS)

Sarov, Y; Ivanov, Tz; Frank, A; Zoellner, J-P; Nikolov, N; Rangelow, I W

2010-01-01

This paper reports on the fabrication and characterisation of self-actuating, and self-sensing cantilever arrays for large-scale parallel surface scanning. Each cantilever is integrated with a sharp silicon tip, a thermal-driven bimorph actuator, and a piezoresistive deflection sensor. Thus, the tip to the sample distance can be controlled individually for each cantilever. A radius of the tips below 10 nm is obtained, which enables nanometre in-plane surface imaging by Angstrom resolution in vertical direction. The fabricated cantilever probe arrays are also applicable for large-area manipulation, sub-10 nm metrology, bottom-up synthesis, high-speed gas analysis, for different bio-applications like recognition of DNA, RNA, or various biomarkers of a single disease, etc.

A new macro-micro dual drive parallel robot for chromosome dissection

Energy Technology Data Exchange (ETDEWEB)

Feng, Jin; Gao, Feng; Zhao, Xianchao; Yue, Yi; Liu, Renqiang [Shanghai Jiao Tong University, Shanghai (China)

2012-01-15

This paper presents a parallel-structure system dually driven by six servo motors and six piezoelectric actuators. Due to the combination of macro and micro manipulators which are both of orthogonal structures, the proposed system possesses a concise structure as well as actuation isolation and output motion decoupling properties. By using a glass needle mounted on a six-dimensional force sensor in endpoint operating, this system can be applied to chromosome dissection that to make the whole process more efficient and automatic. The glass needle tip has a stroke of 106 mm in three linear motions and 18.7-arc-degrees in three angle motion directions, with servo motors adopted. It also has the resolution of 20 nanometers with the adoption of piezoelectric actuators. The kinematics, isotropy, decoupling and design considerations of the proposed robot are discussed. Workspace and resolution of both macro and micro manipulators are measured separately. The experiments are also conducted to show its capability in dissecting chromosomes.

An Intrinsic Algorithm for Parallel Poisson Disk Sampling on Arbitrary Surfaces.

Science.gov (United States)

Ying, Xiang; Xin, Shi-Qing; Sun, Qian; He, Ying

2013-03-08

Poisson disk sampling plays an important role in a variety of visual computing, due to its useful statistical property in distribution and the absence of aliasing artifacts. While many effective techniques have been proposed to generate Poisson disk distribution in Euclidean space, relatively few work has been reported to the surface counterpart. This paper presents an intrinsic algorithm for parallel Poisson disk sampling on arbitrary surfaces. We propose a new technique for parallelizing the dart throwing. Rather than the conventional approaches that explicitly partition the spatial domain to generate the samples in parallel, our approach assigns each sample candidate a random and unique priority that is unbiased with regard to the distribution. Hence, multiple threads can process the candidates simultaneously and resolve conflicts by checking the given priority values. It is worth noting that our algorithm is accurate as the generated Poisson disks are uniformly and randomly distributed without bias. Our method is intrinsic in that all the computations are based on the intrinsic metric and are independent of the embedding space. This intrinsic feature allows us to generate Poisson disk distributions on arbitrary surfaces. Furthermore, by manipulating the spatially varying density function, we can obtain adaptive sampling easily.

Spatial Manipulation and Assembly of Nanoparticles by Atomic Force Microscopy Tip-Induced Dielectrophoresis.

Science.gov (United States)

Zhou, Peilin; Yu, Haibo; Yang, Wenguang; Wen, Yangdong; Wang, Zhidong; Li, Wen Jung; Liu, Lianqing

2017-05-17

In this article, we present a novel method of spatial manipulation and assembly of nanoparticles via atomic force microscopy tip-induced dielectrophoresis (AFM-DEP). This method combines the high-accuracy positioning of AFM with the parallel manipulation of DEP. A spatially nonuniform electric field is induced by applying an alternating current (AC) voltage between the conductive AFM probe and an indium tin oxide glass substrate. The AFM probe acted as a movable DEP tweezer for nanomanipulation and assembly of nanoparticles. The mechanism of AFM-DEP was analyzed by numerical simulation. The effects of solution depth, gap distance, AC voltage, solution concentration, and duration time were experimentally studied and optimized. Arrays of 200 nm polystyrene nanoparticles were assembled into various nanostructures, including lines, ellipsoids, and arrays of dots. The sizes and shapes of the assembled structures were controllable. It was thus demonstrated that AFM-DEP is a flexible and powerful tool for nanomanipulation.

Compliant Aerial Manipulators

DEFF Research Database (Denmark)

Bartelds, T.; Capra, A.; Hamaza, S.

2016-01-01

joints. The approach aims at limiting the influence of impacts on the controlled attitude dynamics in order to allow the aerial manipulator to remain stable during and after impact. The developed concept is intended to convert kinetic energy into potential energy, which is permanently stored into elastic...... elements by means of directional locking mechanisms. The proposed approach has been tested on a 2 d.o.f. manipulator mounted on a quadrotor UAV. The manipulation system has one active rotational d.o.f. compensating for pitch movements of the UAV and one passive linear joint which is in charge of absorbing...... the impact energy. The device has been used to validate the method through experiments, in comparison with a rigid manipulator. The results show that the proposed approach and the developed mechanical system achieve stable impact absorption without bouncing away from the interacting environment. Our work has...

Modelling and Experimental Evaluation of a Static Balancing Technique for a New Horizontally Mounted 3-UPU Parallel Mechanism

Directory of Open Access Journals (Sweden)

Maryam Banitalebi Dehkordi

2012-11-01

Full Text Available This paper presents the modelling and experimental evaluation of the gravity compensation of a horizontal 3-UPU parallel mechanism. The conventional Newton-Euler method for static analysis and balancing of mechanisms works for serial robots; however, it can become computationally expensive when applied to the analysis of parallel manipulators. To overcome this difficulty, in this paper we propose an approach, based on a Lagrangian method, that is more efficient in terms of computation time. The derivation of the gravity compensation model is based on the analytical computation of the total potential energy of the system at each position of the end-effector. In order to satisfy the gravity compensation condition, the total potential energy of the system should remain constant for all of the manipulator's configurations. Analytical and mechanical gravity compensation is taken into account, and the set of conditions and the system of springs are defined. Finally, employing a virtual reality environment, some experiments are carried out and the reliability and feasibility of the proposed model are evaluated in the presence and absence of the elastic components.

Understanding pharmaceutical research manipulation in the context of accounting manipulation.

Science.gov (United States)

Brown, Abigail

2013-01-01

The problem of the manipulation of data that arises when there is both opportunity and incentive to mislead is better accepted and studied - though by no means solved - in financial accounting than in medicine. This article analyzes pharmaceutical company manipulation of medical research as part of a broader problem of corporate manipulation of data in the creation of accounting profits. The article explores how our understanding of accounting fraud and misinformation helps us understand the risk of similar information manipulation in the medical sciences. This understanding provides a framework for considering how best to improve the quality of medical research and analysis in light of the current system of medical information production. I offer three possible responses: (1) use of the Dodd-Frank whistleblower provisions to encourage reporting of medical research fraud; (2) a two-step academic journal review process for clinical trials; and (3) publicly subsidized trial-failure insurance. These would improve the release of negative information about drugs, thereby increasing the reliability of positive information. © 2013 American Society of Law, Medicine & Ethics, Inc.

An evolutionary resolution of manipulation conflict.

Science.gov (United States)

González-Forero, Mauricio

2014-07-01

Individuals can manipulate the behavior of social partners. However, manipulation may conflict with the fitness interests of the manipulated individuals. Manipulated individuals can then be favored to resist manipulation, possibly reducing or eliminating the manipulated behavior in the long run. I use a mathematical model to show that conflicts where manipulation and resistance coevolve can disappear as a result of the coevolutionary process. I find that while manipulated individuals are selected to resist, they can simultaneously be favored to express the manipulated behavior at higher efficiency (i.e., providing increasing fitness effects to recipients of the manipulated behavior). Efficiency can increase to a point at which selection for resistance disappears. This process yields an efficient social behavior that is induced by social partners, and over which the inducing and induced individuals are no longer in conflict. A necessary factor is costly inefficiency. I develop the model to address the evolution of advanced eusociality via maternal manipulation (AEMM). The model predicts AEMM to be particularly likely in taxa with ancestrally imperfect resistance to maternal manipulation. Costly inefficiency occurs if the cost of delayed dispersal is larger than the benefit of exploiting the maternal patch. I discuss broader implications of the process. © 2014 The Author(s). Evolution © 2014 The Society for the Study of Evolution.

Closed-form dynamics of a hexarot parallel manipulator by means of the principle of virtual work

Science.gov (United States)

Pedrammehr, Siamak; Nahavandi, Saeid; Abdi, Hamid

2018-04-01

In this research, a systematic approach to solving the inverse dynamics of hexarot manipulators is addressed using the methodology of virtual work. For the first time, a closed form of the mathematical formulation of the standard dynamic model is presented for this class of mechanisms. An efficient algorithm for solving this closed-form dynamic model of the mechanism is developed and it is used to simulate the dynamics of the system for different trajectories. Validation of the proposed model is performed using SimMechanics and it is shown that the results of the proposed mathematical model match with the results obtained by the SimMechanics model.

Thin-film-transistor array: an exploratory attempt for high throughput cell manipulation using electrowetting principle

Science.gov (United States)

Shaik, F. Azam; Cathcart, G.; Ihida, S.; Lereau-Bernier, M.; Leclerc, E.; Sakai, Y.; Toshiyoshi, H.; Tixier-Mita, A.

2017-05-01

In lab-on-a-chip (LoC) devices, microfluidic displacement of liquids is a key component. electrowetting on dielectric (EWOD) is a technique to move fluids, with the advantage of not requiring channels, pumps or valves. Fluids are discretized into droplets on microelectrodes and moved by applying an electric field via the electrodes to manipulate the contact angle. Micro-objects, such as biological cells, can be transported inside of these droplets. However, the design of conventional microelectrodes, made by standard micro-fabrication techniques, fixes the path of the droplets, and limits the reconfigurability of paths and thus limits the parallel processing of droplets. In that respect, thin film transistor (TFT) technology presents a great opportunity as it allows infinitely reconfigurable paths, with high parallelizability. We propose here to investigate the possibility of using TFT array devices for high throughput cell manipulation using EWOD. A COMSOL based 2D simulation coupled with a MATLAB algorithm was used to simulate the contact angle modulation, displacement and mixing of droplets. These simulations were confirmed by experimental results. The EWOD technique was applied to a droplet of culture medium containing HepG2 carcinoma cells and demonstrated no negative effects on the viability of the cells. This confirms the possibility of applying EWOD techniques to cellular applications, such as parallel cell analysis.

Thin-film-transistor array: an exploratory attempt for high throughput cell manipulation using electrowetting principle

International Nuclear Information System (INIS)

Shaik, F Azam; Cathcart, G; Toshiyoshi, H; Tixier-Mita, A; Ihida, S; Sakai, Y; Lereau-Bernier, M; Leclerc, E

2017-01-01

In lab-on-a-chip (LoC) devices, microfluidic displacement of liquids is a key component. electrowetting on dielectric (EWOD) is a technique to move fluids, with the advantage of not requiring channels, pumps or valves. Fluids are discretized into droplets on microelectrodes and moved by applying an electric field via the electrodes to manipulate the contact angle. Micro-objects, such as biological cells, can be transported inside of these droplets. However, the design of conventional microelectrodes, made by standard micro-fabrication techniques, fixes the path of the droplets, and limits the reconfigurability of paths and thus limits the parallel processing of droplets. In that respect, thin film transistor (TFT) technology presents a great opportunity as it allows infinitely reconfigurable paths, with high parallelizability. We propose here to investigate the possibility of using TFT array devices for high throughput cell manipulation using EWOD. A COMSOL based 2D simulation coupled with a MATLAB algorithm was used to simulate the contact angle modulation, displacement and mixing of droplets. These simulations were confirmed by experimental results. The EWOD technique was applied to a droplet of culture medium containing HepG2 carcinoma cells and demonstrated no negative effects on the viability of the cells. This confirms the possibility of applying EWOD techniques to cellular applications, such as parallel cell analysis. (paper)

Data driven parallelism in experimental high energy physics applications

International Nuclear Information System (INIS)

Pohl, M.

1987-01-01

I present global design principles for the implementation of high energy physics data analysis code on sequential and parallel processors with mixed shared and local memory. Potential parallelism in the structure of high energy physics tasks is identified with granularity varying from a few times 10 8 instructions all the way down to a few times 10 4 instructions. It follows the hierarchical structure of detector and data acquisition systems. To take advantage of this - yet preserving the necessary portability of the code - I propose a computational model with purely data driven concurrency in Single Program Multiple Data (SPMD) mode. The task granularity is defined by varying the granularity of the central data structure manipulated. Concurrent processes coordiate themselves asynchroneously using simple lock constructs on parts of the data structure. Load balancing among processes occurs naturally. The scheme allows to map the internal layout of the data structure closely onto the layout of local and shared memory in a parallel architecture. It thus allows to optimize the application with respect to synchronization as well as data transport overheads. I present a coarse top level design for a portable implementation of this scheme on sequential machines, multiprocessor mainframes (e.g. IBM 3090), tightly coupled multiprocessors (e.g. RP-3) and loosely coupled processor arrays (e.g. LCAP, Emulating Processor Farms). (orig.)

Data driven parallelism in experimental high energy physics applications

Science.gov (United States)

Pohl, Martin

1987-08-01

I present global design principles for the implementation of High Energy Physics data analysis code on sequential and parallel processors with mixed shared and local memory. Potential parallelism in the structure of High Energy Physics tasks is identified with granularity varying from a few times 10 8 instructions all the way down to a few times 10 4 instructions. It follows the hierarchical structure of detector and data acquisition systems. To take advantage of this - yet preserving the necessary portability of the code - I propose a computational model with purely data driven concurrency in Single Program Multiple Data (SPMD) mode. The Task granularity is defined by varying the granularity of the central data structure manipulated. Concurrent processes coordinate themselves asynchroneously using simple lock constructs on parts of the data structure. Load balancing among processes occurs naturally. The scheme allows to map the internal layout of the data structure closely onto the layout of local and shared memory in a parallel architecture. It thus allows to optimize the application with respect to synchronization as well as data transport overheads. I present a coarse top level design for a portable implementation of this scheme on sequential machines, multiprocessor mainframes (e.g. IBM 3090), tightly coupled multiprocessors (e.g. RP-3) and loosely coupled processor arrays (e.g. LCAP, Emulating Processor Farms).

Manipulation, salience, and nudges.

Science.gov (United States)

Noggle, Robert

2018-03-01

Cass Sunstein and Richard Thaler recommend helping people make better decisions by employing 'nudges', which they define as noncoercive methods of influencing choice for the better. Not surprisingly, healthcare practitioners and public policy professionals have become interested in whether nudges might be a promising method of improving health-related behaviors without resorting to heavy-handed methods such as coercion, deception, or government regulation. Many nudges seem unobjectionable as they merely improve the quality and quantity available for the decision-maker. However, other nudges influence decision-making in ways that do not involve providing more and better information. Nudges of this sort raise concerns about manipulation. This paper will focus on noninformational nudges that operate by changing the salience of various options. It will survey two approaches to understanding manipulation, one which sees manipulation as a kind of pressure, and one that sees it as a kind of trickery. On the pressure view, salience nudges do not appear to be manipulative. However, on the trickery view (which the author favors), salience nudges will be manipulative if they increase the salience so that it is disproportionate to that fact's true relevance and importance for the decision at hand. By contrast, salience nudges will not be manipulative if they merely highlight some fact that is true and important for the decision at hand. The paper concludes by providing examples of both manipulative and nonmanipulative salience nudges. © 2017 John Wiley & Sons Ltd.

Analysis on the Load Carrying Mechanism Integrated as Heterogeneous Co-operative Manipulator in a Walking Wheelchair

Science.gov (United States)

Rajay Vedaraj, I. S.; Jain, Ritika; Rao, B. V. A.

2014-07-01

After industrial robots came into existence during 1960, the technology of robotics with the design and analysis of robots in various forms in industries as well as in domestic applications were developed. Nowadays, along with the automotive sector the robots are producing a great impact in the form of quality and production rate to register their existence reliable in various other sectors also. Robotic technology has undergone various phase translations from being tortured as humanoids to the present day manipulators. Depending upon the various forms of its existence, robot manipulators are designed as serial manipulators and parallel manipulators. Individually both types can be proved effective though both have various drawbacks in design and the kinematic analysis. The versatility of robots can be increased by making them work in an environment where the same work volume is shared by more than one manipulator. This work volume can be identified as co-operative work volume of those manipulators. Here the interference of manipulators in the work volume of other manipulators is possible and is made obstacle free. The main advantage of co-operative manipulators is that when a number of independent manipulators are put together in a cooperative work envelope the efficiency and ability to perform tasks is greatly enhanced. The main disadvantage of the co-operative manipulators lies in the complication of its design even for a simple application, in almost all fields. In this paper, a cooperative design of robot manipulators to work in co-operative work environment is done and analysed for its efficacy. In the industrial applications when robotic manipulators are put together in more numbers, the trajectory planning becomes the tough task in the work cell. Proper design can remove the design defects of the cooperative manipulators and can be utilized in a more efficient way. In the proposed research paper an analysis is made on such a type of cooperative manipulator

Analysis on the Load Carrying Mechanism Integrated as Heterogeneous Co-operative Manipulator in a Walking Wheelchair

International Nuclear Information System (INIS)

Vedaraj, I S Rajay; Jain, Ritika; Rao, B V A

2014-01-01

After industrial robots came into existence during 1960, the technology of robotics with the design and analysis of robots in various forms in industries as well as in domestic applications were developed. Nowadays, along with the automotive sector the robots are producing a great impact in the form of quality and production rate to register their existence reliable in various other sectors also. Robotic technology has undergone various phase translations from being tortured as humanoids to the present day manipulators. Depending upon the various forms of its existence, robot manipulators are designed as serial manipulators and parallel manipulators. Individually both types can be proved effective though both have various drawbacks in design and the kinematic analysis. The versatility of robots can be increased by making them work in an environment where the same work volume is shared by more than one manipulator. This work volume can be identified as co-operative work volume of those manipulators. Here the interference of manipulators in the work volume of other manipulators is possible and is made obstacle free. The main advantage of co-operative manipulators is that when a number of independent manipulators are put together in a cooperative work envelope the efficiency and ability to perform tasks is greatly enhanced. The main disadvantage of the co-operative manipulators lies in the complication of its design even for a simple application, in almost all fields. In this paper, a cooperative design of robot manipulators to work in co-operative work environment is done and analysed for its efficacy. In the industrial applications when robotic manipulators are put together in more numbers, the trajectory planning becomes the tough task in the work cell. Proper design can remove the design defects of the cooperative manipulators and can be utilized in a more efficient way. In the proposed research paper an analysis is made on such a type of cooperative manipulator

Cell manipulation in microfluidics

International Nuclear Information System (INIS)

Yun, Hoyoung; Kim, Kisoo; Lee, Won Gu

2013-01-01

Recent advances in the lab-on-a-chip field in association with nano/microfluidics have been made for new applications and functionalities to the fields of molecular biology, genetic analysis and proteomics, enabling the expansion of the cell biology field. Specifically, microfluidics has provided promising tools for enhancing cell biological research, since it has the ability to precisely control the cellular environment, to easily mimic heterogeneous cellular environment by multiplexing, and to analyze sub-cellular information by high-contents screening assays at the single-cell level. Various cell manipulation techniques in microfluidics have been developed in accordance with specific objectives and applications. In this review, we examine the latest achievements of cell manipulation techniques in microfluidics by categorizing externally applied forces for manipulation: (i) optical, (ii) magnetic, (iii) electrical, (iv) mechanical and (v) other manipulations. We furthermore focus on history where the manipulation techniques originate and also discuss future perspectives with key examples where available. (topical review)

Manipulator comparative testing program

International Nuclear Information System (INIS)

Draper, J.V.; Handel, S.J.; Sundstrom, E.; Herndon, J.N.; Fujita, Y.; Maeda, M.

1986-01-01

The Manipulator Comparative Testing Program examined differences among manipulator systems from the United States and Japan. The manipulator systems included the Meidensha BILARM 83A, the Model M-2 of Central Research Laboratories Division of Sargent Industries (CRL), and the GCA Corporation PaR Systems Model 6000. The site of testing was the Remote Operations Maintenance Demonstration (ROMD) facility, operated by the Fuel Recycle Division in the Consolidated Fuel Reprocessing Program at the Oak Ridge National Laboratory (ORNL). In all stages of testing, operators using the CRL Model M-2 manipulator had consistently lower times to completion and error rates than they did using other machines. Performance was second best with the Meidensha BILARM 83A in master-slave mode. Performance with the BILARM in switchbox mode and the PaR 6000 manipulator was approximately equivalent in terms of criteria recorded in testing. These data show no impact of force reflection on task performance

Cell manipulation tool with combined microwell array and optical tweezers for cell isolation and deposition

International Nuclear Information System (INIS)

Wang, Xiaolin; Gou, Xue; Chen, Shuxun; Yan, Xiao; Sun, Dong

2013-01-01

Isolation from rare cells and deposition of sorted cells with high accuracy for further study are critical to a wide range of biomedical applications. In the current paper, we report an automated cell manipulation tool with combined optical tweezers and a uniquely designed microwell array, which functions for recognition, isolation, assembly, transportation and deposition of the interesting cells. The microwell array allows the passive hydrodynamic docking of cells, while offering the opportunity to inspect the interesting cell phenotypes with high spatio-temporal resolution based on the flexible image processing technique. In addition, dynamic and parallel cell manipulation in three dimensions can realize the target cell levitation from microwell and pattern assembly with multiple optical traps. Integrated with the programmed motorized stage, the optically levitated and assembled cells can be transported and deposited to the predefined microenvironment, so the tool can facilitate the integration of other on-chip functionalities for further study without removing these isolated cells from the chip. Experiments on human embryonic stem cells and yeast cells are performed to demonstrate the effectiveness of the proposed cell manipulation tool. Besides the application to cell isolation and deposition, three other biological applications with this tool are also presented. (paper)

Parallel Programming with Intel Parallel Studio XE

CERN Document Server

Blair-Chappell , Stephen

2012-01-01

Optimize code for multi-core processors with Intel's Parallel Studio Parallel programming is rapidly becoming a "must-know" skill for developers. Yet, where to start? This teach-yourself tutorial is an ideal starting point for developers who already know Windows C and C++ and are eager to add parallelism to their code. With a focus on applying tools, techniques, and language extensions to implement parallelism, this essential resource teaches you how to write programs for multicore and leverage the power of multicore in your programs. Sharing hands-on case studies and real-world examples, the

Master-slave manipulator

International Nuclear Information System (INIS)

Haaker, L.W.; Jelatis, D.G.

1981-01-01

A remote control master-slave manipulator for performing work on the opposite side of a barrier wall, is described. The manipulator consists of a rotatable horizontal support adapted to extend through the wall and two longitudinally extensible arms, a master and a slave, pivotally connected one to each end of the support. (U.K.)

Configuration Synthesis for Fully Restrained 7-Cable-Driven Manipulators

Directory of Open Access Journals (Sweden)

Xiaoqiang Tang

2012-10-01

Full Text Available Cable distribution plays a vital role in Cable Driven Parallel Manipulators (CDPMs regarding tension and workspace quality, especially in fully restrained CDPMs. This paper focuses on three typical configurations of fully restrained CDPMs with 7 cables in order to introduce an approach for configuration synthesis. Firstly, the kinematic models of three types of CDPMs with 7 cables are set up. Then, in order to evaluate workspace quality, two new indices are proposed by using tensions along each cable, which are the All Cable Tension Distribution Index (ACTDI and Global Tension Distribution Index (GTDI. Next, the three types of CDPMs with 7 cables are analysed with the two indices. At the end, according to different performance requirements, the configurations of cable distribution are discussed and selected.

Leadership Manipulation and Ethics in Storytelling

OpenAIRE

Auvinen, Tommi; Lämsä, Anna-Maija; Sintonen, Teppo; Takala, Tuomo

2013-01-01

This article focuses on exerting influence in leadership, namely manipulation in storytelling. Manipulation is usually considered an unethical approach to leadership. We will argue that manipulation is a more complex phenomenon than just an unethical way of acting in leadership. We will demonstrate through an empirical qualitative study that there are various types of manipulation through storytelling. This article makes a contribution to the literature on manipulation through leadership stor...

MATHEMATICAL MODEL MANIPULATOR ROBOTS

Directory of Open Access Journals (Sweden)

O. N. Krakhmalev

2015-12-01

Full Text Available A mathematical model to describe the dynamics of manipulator robots. Mathematical model are the implementation of the method based on the Lagrange equation and using the transformation matrices of elastic coordinates. Mathematical model make it possible to determine the elastic deviations of manipulator robots from programmed motion trajectories caused by elastic deformations in hinges, which are taken into account in directions of change of the corresponding generalized coordinates. Mathematical model is approximated and makes it possible to determine small elastic quasi-static deviations and elastic vibrations. The results of modeling the dynamics by model are compared to the example of a two-link manipulator system. The considered model can be used when performing investigations of the mathematical accuracy of the manipulator robots.

Belief–logic conflict resolution in syllogistic reasoning: Inspection-time evidence for a parallel process model

OpenAIRE

Stupple, Edward J.N; Ball, Linden

2008-01-01

An experiment is reported examining dual-process models of belief bias in syllogistic reasoning using a problem complexity manipulation and an inspection-time method to monitor processing latencies for premises and conclusions. Endorsement rates indicated increased belief bias on complex problems, a finding that runs counter to the “belief-first” selective scrutiny model, but which is consistent with other theories, including “reasoning-first” and “parallel-process” models. Inspection-time da...

Adaptive control of robotic manipulators

Science.gov (United States)

Seraji, H.

1987-01-01

The author presents a novel approach to adaptive control of manipulators to achieve trajectory tracking by the joint angles. The central concept in this approach is the utilization of the manipulator inverse as a feedforward controller. The desired trajectory is applied as an input to the feedforward controller which behaves as the inverse of the manipulator at any operating point; the controller output is used as the driving torque for the manipulator. The controller gains are then updated by an adaptation algorithm derived from MRAC (model reference adaptive control) theory to cope with variations in the manipulator inverse due to changes of the operating point. An adaptive feedback controller and an auxiliary signal are also used to enhance closed-loop stability and to achieve faster adaptation. The proposed control scheme is computationally fast and does not require a priori knowledge of the complex dynamic model or the parameter values of the manipulator or the payload.

A Direct Kinematics Problem Solution for the Three-degree-of-freedom Parallel Structure Manipulator Based on Crank Mechanism

Directory of Open Access Journals (Sweden)

V. N. Paschenko

2015-01-01

Full Text Available The paper describes a mechanism representing a kind of mechanisms of parallel kinematics with three degrees of freedom based on the crank mechanism. This mechanism consists of two platforms, namely: the lower fixed and the upper movable. The upper platform is connected to the lower one by six movable elements, three of which are rods attached to the bases by means of spherical joints, and another three have a crank structure.The paper shows an approach to the solution of a direct task of kinematics based on mathematical modeling. The inverse problem of kinematics is formulated as follows: at specified angles of rotation drive (the values of generalized coordinates to determine the position of the top mobile platform.To solve this problem has been used a mathematical model describing the proposed system. On the basis of the constructed model were made the necessary calculations that allowed us using the values of crank angles connected with the engines to determine the position of the platform in space. To solve the problem we used the method of virtual points to reduce the number of equations and unknowns, which determine the position of the upper platform in space, at a crucial system from eighteen to nine, thus simplifying the solution.To check the solution correctness was carried out numerical experiment. Each generalized coordinate took on values in the range from -30 ° to 30 °; for them a direct positional problem was solved, and its result was inserted, as initial data, in the previous solved and proven inverse problem on the position of the platform under study.The paper presents comparative results of measurements with the calculated values of the generalized coordinates and draws the appropriate conclusions, that this model is in good compliance with the results observed in practice. One of the distinctive features of the proposed approach is that rotation angles of engines are used as the generalized coordinates. This allowed us

Using Manipulatives in Math Instruction.

Science.gov (United States)

Marzola, Eileen S.

1987-01-01

Guidelines for teachers to better use manipulatives in the teaching of mathematics to learning disabled learners are offered including a rationale for manipulatives, selection crteria, principles underlying productive use of manipulatives, and making the transition from the concrete to the symbolic. Suggested materials and distributors are listed.…

Kinematics of an in-parallel actuated manipulator based on the Stewart platform mechanism

Science.gov (United States)

Williams, Robert L., II

1992-01-01

This paper presents kinematic equations and solutions for an in-parallel actuated robotic mechanism based on Stewart's platform. These equations are required for inverse position and resolved rate (inverse velocity) platform control. NASA LaRC has a Vehicle Emulator System (VES) platform designed by MIT which is based on Stewart's platform. The inverse position solution is straight-forward and computationally inexpensive. Given the desired position and orientation of the moving platform with respect to the base, the lengths of the prismatic leg actuators are calculated. The forward position solution is more complicated and theoretically has 16 solutions. The position and orientation of the moving platform with respect to the base is calculated given the leg actuator lengths. Two methods are pursued in this paper to solve this problem. The resolved rate (inverse velocity) solution is derived. Given the desired Cartesian velocity of the end-effector, the required leg actuator rates are calculated. The Newton-Raphson Jacobian matrix resulting from the second forward position kinematics solution is a modified inverse Jacobian matrix. Examples and simulations are given for the VES.

Balanced articulated manipulator

International Nuclear Information System (INIS)

Francois, Daniel; Germond, J.-C.; Marchal, Paul; Vertut, Jean.

1976-01-01

The description is given of a manipulator of the type comprising a master arm and a slave arm, capable of working in a containment restricted by a wall fitted with an aperture to introduce the slave arm into the containment. According to the invention this manipulator is permanently balanced irrespective of its distortions when it is secured to the wall of the containment in which it is desired to work. The entire manipulator is also balanced when being set up and when moved outside the containment, in relation to a supporting axle. This result is achieved in a simplified manner by giving homothetic shapes to the various component parts of the slave and master arms, the master arm having at least one balancing weight [fr

Direct Manipulation in Virtual Reality

Science.gov (United States)

Bryson, Steve

2003-01-01

Virtual Reality interfaces offer several advantages for scientific visualization such as the ability to perceive three-dimensional data structures in a natural way. The focus of this chapter is direct manipulation, the ability for a user in virtual reality to control objects in the virtual environment in a direct and natural way, much as objects are manipulated in the real world. Direct manipulation provides many advantages for the exploration of complex, multi-dimensional data sets, by allowing the investigator the ability to intuitively explore the data environment. Because direct manipulation is essentially a control interface, it is better suited for the exploration and analysis of a data set than for the publishing or communication of features found in that data set. Thus direct manipulation is most relevant to the analysis of complex data that fills a volume of three-dimensional space, such as a fluid flow data set. Direct manipulation allows the intuitive exploration of that data, which facilitates the discovery of data features that would be difficult to find using more conventional visualization methods. Using a direct manipulation interface in virtual reality, an investigator can, for example, move a data probe about in space, watching the results and getting a sense of how the data varies within its spatial volume.

Tile-based parallel coordinates and its application in financial visualization

Science.gov (United States)

Alsakran, Jamal; Zhao, Ye; Zhao, Xinlei

2010-01-01

Parallel coordinates technique has been widely used in information visualization applications and it has achieved great success in visualizing multivariate data and perceiving their trends. Nevertheless, visual clutter usually weakens or even diminishes its ability when the data size increases. In this paper, we first propose a tile-based parallel coordinates, where the plotting area is divided into rectangular tiles. Each tile stores an intersection density that counts the total number of polylines intersecting with that tile. Consequently, the intersection density is mapped to optical attributes, such as color and opacity, by interactive transfer functions. The method visualizes the polylines efficiently and informatively in accordance with the density distribution, and thus, reduces visual cluttering and promotes knowledge discovery. The interactivity of our method allows the user to instantaneously manipulate the tiles distribution and the transfer functions. Specifically, the classic parallel coordinates rendering is a special case of our method when each tile represents only one pixel. A case study on a real world data set, U.S. stock mutual fund data of year 2006, is presented to show the capability of our method in visually analyzing financial data. The presented visual analysis is conducted by an expert in the domain of finance. Our method gains the support from professionals in the finance field, they embrace it as a potential investment analysis tool for mutual fund managers, financial planners, and investors.

Geometric control of manipulators

International Nuclear Information System (INIS)

Thiruarooran, C.

1996-01-01

Resolved motion control enables the end effector to be moved as a rigid body in space without having to work out manually the joint combinations needed. Since a rigid body in space has three independent translational and three independent rotational movements, a manipulator with at least six joints can be controlled in this way. Normally the manipulator has more than six joints providing an infinite number of ways of moving the tip in the desired direction and this redundancy can be exploited in a variety of ways. Resolved motion tests performed on a hydraulically operated heavy duty manipulator at the Dungeness nuclear power plant are described. The results have shown that manipulators with as many as ten joints can be controlled under resolved tip motion and the areas which are critical to the performance of this type of control have been identified. (UK)

Control of a flexible bracing manipulator: Integration of current research work to realize the bracing manipulator

Science.gov (United States)

Kwon, Dong-Soo

1991-01-01

All research results about flexible manipulator control were integrated to show a control scenario of a bracing manipulator. First, dynamic analysis of a flexible manipulator was done for modeling. Second, from the dynamic model, the inverse dynamic equation was derived, and the time domain inverse dynamic method was proposed for the calculation of the feedforward torque and the desired flexible coordinate trajectories. Third, a tracking controller was designed by combining the inverse dynamic feedforward control with the joint feedback control. The control scheme was applied to the tip position control of a single link flexible manipulator for zero and non-zero initial condition cases. Finally, the contact control scheme was added to the position tracking control. A control scenario of a bracing manipulator is provided and evaluated through simulation and experiment on a single link flexible manipulator.

Modeling the manipulator and flipper pose effects on tip over stability of a tracked mobile manipulator

CSIR Research Space (South Africa)

Dube, C

2011-11-01

Full Text Available Mobile manipulators are used in a number of different applications such as bomb disposal, mining robotics, and search and rescue operations. These mobile manipulators are highly susceptible to tip over due to the motion of the manipulator...

What is adaptive about adaptive decision making? A parallel constraint satisfaction account.

Science.gov (United States)

Glöckner, Andreas; Hilbig, Benjamin E; Jekel, Marc

2014-12-01

There is broad consensus that human cognition is adaptive. However, the vital question of how exactly this adaptivity is achieved has remained largely open. Herein, we contrast two frameworks which account for adaptive decision making, namely broad and general single-mechanism accounts vs. multi-strategy accounts. We propose and fully specify a single-mechanism model for decision making based on parallel constraint satisfaction processes (PCS-DM) and contrast it theoretically and empirically against a multi-strategy account. To achieve sufficiently sensitive tests, we rely on a multiple-measure methodology including choice, reaction time, and confidence data as well as eye-tracking. Results show that manipulating the environmental structure produces clear adaptive shifts in choice patterns - as both frameworks would predict. However, results on the process level (reaction time, confidence), in information acquisition (eye-tracking), and from cross-predicting choice consistently corroborate single-mechanisms accounts in general, and the proposed parallel constraint satisfaction model for decision making in particular. Copyright © 2014 Elsevier B.V. All rights reserved.

Extended Model-Based Feedforward Compensation in L1 Adaptive Control for Mechanical Manipulators: Design and Experiments

Directory of Open Access Journals (Sweden)

Moussab eBennehar

2015-12-01

Full Text Available This paper deals with a new control scheme for Parallel Kinematic Manipulators (PKMs based on the L1 adaptive control theory. The original L1 adaptive controller is extended by including an adaptive loop based on the dynamics of the PKM. The additional model-based term is in charge of the compensation of the modeled nonlinear dynamics in the aim of improving the tracking performance. Moreover, the proposed controller is enhanced to reduce the internal forces, which may appear in the case of Redundantly Actuated PKMs (RA-PKMs. The generated control inputs are first regulated through a projection mechanism that reduces the antagonistic internal forces, before being applied to the manipulator. To validate the proposed controller and to show its effectiveness, real-time experiments are conducted on a new four degrees-of-freedom (4-DOFs RA-PKM developed in our laboratory.

Acoustic streaming in the transducer plane in ultrasonic particle manipulation devices.

Science.gov (United States)

Lei, Junjun; Glynne-Jones, Peter; Hill, Martyn

2013-06-07

In acoustofluidic manipulation and sorting devices, Rayleigh streaming flows are typically found in addition to the acoustic radiation forces. However, experimental work from various groups has described acoustic streaming that occurs in planar devices in a plane parallel to the transducer face. This is typically a four-quadrant streaming pattern with the circulation parallel to the transducer. Understanding its origins is essential for creating designs that limit or control this phenomenon. The cause of this kind of streaming pattern has not been previously explained as it is different from the well-known classical streaming patterns such as Rayleigh streaming and Eckart streaming, whose circulation planes are generally perpendicular to the face of the acoustic transducer. In order to gain insight into these patterns we present a numerical method based on Nyborg's limiting velocity boundary condition that includes terms ignored in the Rayleigh analysis, and verify its predictions against experimental PIV results in a simple device. The results show that the modelled particle trajectories match those found experimentally. Analysis of the dominant terms in the driving equations shows that the origin of this kind of streaming pattern is related to the circulation of the acoustic intensity.

In Praise of Manipulation

NARCIS (Netherlands)

Dowding, Keith; Van Hees, Martin

Many theorists believe that the manipulation of voting procedures is a serious problem. Accordingly, much of social choice theory examines the conditions under which strategy-proofness can be ensured, and what kind of procedures do a better job of preventing manipulation. This article argues that

Powered manipulator control arm

International Nuclear Information System (INIS)

Le Mouee, Theodore; Vertut, Jean; Marchal, Paul; Germon, J.C.; Petit, Michel

1975-01-01

A remote operated control arm for powered manipulators is described. It includes an assembly allowing several movements with position sensors for each movement. The number of possible arm movements equals the number of possible manipulator movements. The control systems may be interrupted as required. One part of the arm is fitted with a system to lock it with respect to another part of the arm without affecting the other movements, so long as the positions of the manipulator and the arm have not been brought into complete coincidence. With this system the locking can be ended when complete concordance is achieved [fr

The direct manipulation shell

International Nuclear Information System (INIS)

Allen, M.E.; Christiansen, M.

1992-01-01

Accelerator controls systems provide parameter display pages which allow the operator to monitor and manipulate selected control points in the system. Display pages are generally implemented as either hand-crafted, purpose-built programs; or by using a specialized display page layout tool. These two methods of display page development exhibit the classic trade-off between functionality vs. ease of implementation. In the Direct Manipulation Shell we approach the process of developing a display page in a manifestly object-oriented manner. This is done by providing a general framework for interactively instantiating and manipulating display objects. (author)

Image manipulation as research misconduct.

Science.gov (United States)

Parrish, Debra; Noonan, Bridget

2009-06-01

A growing number of research misconduct cases handled by the Office of Research Integrity involve image manipulations. Manipulations may include simple image enhancements, misrepresenting an image as something different from what it is, and altering specific features of an image. Through a study of specific cases, the misconduct findings associated with image manipulation, detection methods and those likely to identify such manipulations, are discussed. This article explores sanctions imposed against guilty researchers and the factors that resulted in no misconduct finding although relevant images clearly were flawed. Although new detection tools are available for universities and journals to detect questionable images, this article explores why these tools have not been embraced.

Long-reach manipulators for decommissioning

International Nuclear Information System (INIS)

Webster, D.A.; Challinor, S.F.

1993-01-01

A survey of redundant facilities at Sellafield has identified that in many cases the conventional means of deploying remote handling equipment are not appropriate and that novel means must be employed. However, decommissioning is not a value adding activity and so expensive one off designs must be avoided. The paper will describe BNFL's approach to the synthesis from proprietary parts of a manipulator which can lift 3 te at a horizontal reach of over 5 metres and yet can still perform the dextrous manipulation necessary to remove small items. It will also cover the development of the manipulator control systems and the adaption of commercial handtools to be manipulator friendly. (author)

The Manipulative Discourse of Gandalf

Directory of Open Access Journals (Sweden)

Farid Mohammadi

2014-07-01

Full Text Available The aim of this essay is to investigate discursive, cognitive and social aspects of manipulation in regard to the dialogues of the literary fictional character of Gandalf in the trilogy of The Lord of the Rings. Accordingly, the researcher has taken a multidisciplinary approach to an account of discursive manipulation, and focuses on the cognitive dimensions of manipulation. As a result, the researcher demonstrates meticulously how manipulation involves intensifying the power, moral superiority and the credibility of the speaker(s, while abusing the others (recipients, along with an emotional and attractive way of expression, and supplemented by reasonable facts and documents in regard to a specific issue.

Hydraulic manipulator

International Nuclear Information System (INIS)

Sinha, A.K.; Srikrishnamurty, G.

1990-01-01

Successful operation of nuclear plant is largely dependent on safe handling of radio-active material. In order to reduce this handling problem and minimise the exposure of radiation, various handling equipment and manipulators have been developed according to the requirements. Manufacture of nuclear fuel, which is the most important part of the nuclear industry, involves handling of uranium ingots weighing approximately 250 kg. This paper describes a specially designed hydraulic manipulator for handling of the ingots in a limited space. It was designed to grab and handle the ingots in any position. This has following drive motions: (1)gripping and releasing, (2)lifting and lowering (z-motion), (3)rotation about the horizontal axis (azimuth drive), (4)rotation about the job axis, and (5)rotation about the vertical axis. For horizontal motion (X and Y axis motion) this equipment is mounted on a motorised trolley, so that it can move inside the workshop. For all drives except the rotation about the job axis, hydraulic cylinders have been used with a battery operated power pack. Trolley drive is also given power from same battery. This paper describes the design aspects of this manipulator. (author). 4 figs

CLIMAN - a mobile manipulator concept

International Nuclear Information System (INIS)

Noltingk, B.E.; Owen, C.K.V.

With increasing age the integrity of more remote parts of reactors, such as the core restraints, is questioned so there is a need for a means of access to these places to carry out inspection, minor repairs and alterations. Conventional standpipe manipulators are about 20 m long so that extending them further presents difficulties of load capacity, rigidity, dexterity and control which must increase steeply with range. The proposal outlined here is for a mobile manipulator which can climb at the end of a cable (CLImbing MANipulator - CLIMAN) into a reactor and reach well beyond the range of a fixed base machine. In addition to virtually unlimited range such a mobile manipulator has twice as many degrees of freedom as a fixed base machine. Its body or base can be manoeuvred with six degrees of freedom so as to obtain the maximum coverage and obstacle avoidance for its manipulator. It is proposed that it should be manually controlled. (author)

Interpersonal relationship manipulation at a personal level

Directory of Open Access Journals (Sweden)

Andreja Hribernik

2010-12-01

Full Text Available Manipulation is not unknown or strange to any of us. We have all experienced it, or perhaps even practiced it. It is wrong not to recognize it, to find excuses for it, and, above all, it is wrong not to decide to change one’s behaviour. Long-lasting use of manipulation leaves consequences on all the parties involved: the victim, the observer and the perpetrator. Manipulation is a relation between persons which does not consider the needs of everybody involved. It means exploitation and misleading, inhumane and unethical behaviour on the part of the manipulator, which he uses in order gain success, self-confirmation and to achieve his goals. In the act of manipulation personal boundaries of the other person are violated since the manipulator enforces his dominance and subjectedness of the victim. The manipulator invades the victim’s personal integrity, limiting their potential. He isolates, controls and intimidates them; by devises a system to catch the victims, to entangle them in his net and suck them up like a spider. If the manipulation is very successful, the other person does not recognize it as such; they consider themselves happy to be cooperating with the manipulator, as they identify his goals as their own. Therefore, the manipulator can be said to have stolen the manipulated person’s soul.

Practical parallel computing

CERN Document Server

Morse, H Stephen

1994-01-01

Practical Parallel Computing provides information pertinent to the fundamental aspects of high-performance parallel processing. This book discusses the development of parallel applications on a variety of equipment.Organized into three parts encompassing 12 chapters, this book begins with an overview of the technology trends that converge to favor massively parallel hardware over traditional mainframes and vector machines. This text then gives a tutorial introduction to parallel hardware architectures. Other chapters provide worked-out examples of programs using several parallel languages. Thi

Fundamental physics issues of multilevel logic in developing a parallel processor.

Science.gov (United States)

Bandyopadhyay, Anirban; Miki, Kazushi

2007-06-01

In the last century, On and Off physical switches, were equated with two decisions 0 and 1 to express every information in terms of binary digits and physically realize it in terms of switches connected in a circuit. Apart from memory-density increase significantly, more possible choices in particular space enables pattern-logic a reality, and manipulation of pattern would allow controlling logic, generating a new kind of processor. Neumann's computer is based on sequential logic, processing bits one by one. But as pattern-logic is generated on a surface, viewing whole pattern at a time is a truly parallel processing. Following Neumann's and Shannons fundamental thermodynamical approaches we have built compatible model based on series of single molecule based multibit logic systems of 4-12 bits in an UHV-STM. On their monolayer multilevel communication and pattern formation is experimentally verified. Furthermore, the developed intelligent monolayer is trained by Artificial Neural Network. Therefore fundamental weak interactions for the building of truly parallel processor are explored here physically and theoretically.

Parallel rendering

Science.gov (United States)

Crockett, Thomas W.

1995-01-01

This article provides a broad introduction to the subject of parallel rendering, encompassing both hardware and software systems. The focus is on the underlying concepts and the issues which arise in the design of parallel rendering algorithms and systems. We examine the different types of parallelism and how they can be applied in rendering applications. Concepts from parallel computing, such as data decomposition, task granularity, scalability, and load balancing, are considered in relation to the rendering problem. We also explore concepts from computer graphics, such as coherence and projection, which have a significant impact on the structure of parallel rendering algorithms. Our survey covers a number of practical considerations as well, including the choice of architectural platform, communication and memory requirements, and the problem of image assembly and display. We illustrate the discussion with numerous examples from the parallel rendering literature, representing most of the principal rendering methods currently used in computer graphics.

Simulation of robot manipulators

International Nuclear Information System (INIS)

Kress, R.L.; Babcock, S.M.; Bills, K.C.; Kwon, D.S.; Schoenwald, D.A.

1995-01-01

This paper describes Oak Ridge National Laboratory's development of an environment for the simulation of robotic manipulators. Simulation includes the modeling of kinematics, dynamics, sensors, actuators, control systems, operators, and environments. Models will be used for manipulator design, proposal evaluation, control system design and analysis, graphical preview of proposed motions, safety system development, and training. Of particular interest is the development of models for robotic manipulators having at least one flexible link. As a first application, models have been developed for the Pacific Northwest Laboratories' Flexible Beam Testbed which is a one-Degree-Of-Freedom, flexible arm with a hydraulic base actuator. Initial results show good agreement between model and experiment

A six degrees of freedom mems manipulator

NARCIS (Netherlands)

de Jong, B.R.

2006-01-01

This thesis reports about a six degrees of freedom (DOF) precision manipulator in MEMS, concerning concept generation for the manipulator followed by design and fabrication (of parts) of the proposed manipulation concept in MEMS. Researching the abilities of 6 DOF precision manipulation in MEMS is

A control method for manipulators with redundancy

International Nuclear Information System (INIS)

Furusho, Junji; Usui, Hiroyuki

1989-01-01

Redundant manipulators have more ability than nonredundant ones in many aspects such as avoiding obstacles, avoiding singular states, etc. In this paper, a control algorithm for redundant manipulators working under the circumstance in the presence of obstacles is presented. First, the measure of manipulability for robot manipulators under obstacle circumstances is defined. Then, the control algorithm for the obstacle avoidance is derived by using this measure of manipulability. The obstacle avoidance and the maintenance of good posture are simultaneously achieved by this algorithm. Lastly, an experiment and simulation results using an eight degree of freedom manipulator are shown. (author)

Computer control of a multi-link manipulator

International Nuclear Information System (INIS)

Holt, J.E.; Thiruarooran, C.

1988-01-01

The Central Electricity Generating Board has a requirement for a manipulator which can deploy to its work location around obstacles. A multilink manipulator has been designed for this purpose. A computer control system designed to ease manipulator operation is described. Using the control program, the manipulator may be deployed using just 2 joysticks. Experience in the use of the program with an inspection manipulator at Sizewell 'A' Nuclear Power Station is discussed. When used to control a manipulator of 9 hydraulically actuated degrees of freedom, a control accuracy of about 1.5% of full extension has been achieved. (author)

Parallel computations

CERN Document Server

1982-01-01

Parallel Computations focuses on parallel computation, with emphasis on algorithms used in a variety of numerical and physical applications and for many different types of parallel computers. Topics covered range from vectorization of fast Fourier transforms (FFTs) and of the incomplete Cholesky conjugate gradient (ICCG) algorithm on the Cray-1 to calculation of table lookups and piecewise functions. Single tridiagonal linear systems and vectorized computation of reactive flow are also discussed.Comprised of 13 chapters, this volume begins by classifying parallel computers and describing techn

A high-quality narrow passband filter for elastic SV waves via aligned parallel separated thin polymethylmethacrylate plates

OpenAIRE

Jun Zhang; Yaolu Liu; Wensheng Yan; Ning Hu

2017-01-01

We designed a high-quality filter that consists of aligned parallel polymethylmethacrylate (PMMA) thin plates with small gaps for elastic SV waves propagate in metals. Both the theoretical model and the full numerical simulation show the transmission spectrum of the elastic SV waves through such a filter has several sharp peaks with flawless transmission within the investigated frequencies. These peaks can be readily tuned by manipulating the geometry parameters of the PMMA plates. Our invest...

An intrinsic algorithm for parallel Poisson disk sampling on arbitrary surfaces.

Science.gov (United States)

Ying, Xiang; Xin, Shi-Qing; Sun, Qian; He, Ying

2013-09-01

Poisson disk sampling has excellent spatial and spectral properties, and plays an important role in a variety of visual computing. Although many promising algorithms have been proposed for multidimensional sampling in euclidean space, very few studies have been reported with regard to the problem of generating Poisson disks on surfaces due to the complicated nature of the surface. This paper presents an intrinsic algorithm for parallel Poisson disk sampling on arbitrary surfaces. In sharp contrast to the conventional parallel approaches, our method neither partitions the given surface into small patches nor uses any spatial data structure to maintain the voids in the sampling domain. Instead, our approach assigns each sample candidate a random and unique priority that is unbiased with regard to the distribution. Hence, multiple threads can process the candidates simultaneously and resolve conflicts by checking the given priority values. Our algorithm guarantees that the generated Poisson disks are uniformly and randomly distributed without bias. It is worth noting that our method is intrinsic and independent of the embedding space. This intrinsic feature allows us to generate Poisson disk patterns on arbitrary surfaces in IR(n). To our knowledge, this is the first intrinsic, parallel, and accurate algorithm for surface Poisson disk sampling. Furthermore, by manipulating the spatially varying density function, we can obtain adaptive sampling easily.

Dynamic Control of Kinematically Redundant Robotic Manipulators

Directory of Open Access Journals (Sweden)

Erling Lunde

1987-07-01

Full Text Available Several methods for task space control of kinematically redundant manipulators have been proposed in the literature. Most of these methods are based on a kinematic analysis of the manipulator. In this paper we propose a control algorithm in which we are especially concerned with the manipulator dynamics. The algorithm is particularly well suited for the class of redundant manipulators consisting of a relatively small manipulator mounted on a larger positioning part.

Parallel sorting algorithms

CERN Document Server

Akl, Selim G

1985-01-01

Parallel Sorting Algorithms explains how to use parallel algorithms to sort a sequence of items on a variety of parallel computers. The book reviews the sorting problem, the parallel models of computation, parallel algorithms, and the lower bounds on the parallel sorting problems. The text also presents twenty different algorithms, such as linear arrays, mesh-connected computers, cube-connected computers. Another example where algorithm can be applied is on the shared-memory SIMD (single instruction stream multiple data stream) computers in which the whole sequence to be sorted can fit in the

Manipulating Smith-Purcell Emission with Babinet Metasurfaces

Science.gov (United States)

Wang, Zuojia; Yao, Kan; Chen, Min; Chen, Hongsheng; Liu, Yongmin

2016-10-01

Swift electrons moving closely parallel to a periodic grating produce far-field radiation of light, which is known as the Smith-Purcell effect. In this letter, we demonstrate that designer Babinet metasurfaces composed of C -aperture resonators offer a powerful control over the polarization state of the Smith-Purcell emission, which can hardly be achieved via traditional gratings. By coupling the intrinsically nonradiative energy bound at the source current sheet to the out-of-plane electric dipole and in-plane magnetic dipole of the C -aperture resonator, we are able to excite cross-polarized light thanks to the bianisotropic nature of the metasurface. The polarization direction of the emitted light is aligned with the orientation of the C -aperture resonator. Furthermore, the efficiency of the Smith-Purcell emission from Babinet metasurfaces is significantly increased by 84%, in comparison with the case of conventional gratings. These findings not only open up a new way to manipulate the electron-beam-induced emission in the near-field region but also promise compact, tunable, and efficient light sources and particle detectors.

Learning Area and Perimeter with Virtual Manipulatives

Science.gov (United States)

Bouck, Emily; Flanagan, Sara; Bouck, Mary

2015-01-01

Manipulatives are considered a best practice for educating students with disabilities, but little research exists which examines virtual manipulatives as tool for supporting students in mathematics. This project investigated the use of a virtual manipulative through the National Library of Virtual Manipulatives--polynominoes (i.e., tiles)--as a…

Experimental studies of control concepts for a parallel manipulator with flexible links

International Nuclear Information System (INIS)

Burkhardt, Markus; Eberhard, Peter; Seifried, Robert

2015-01-01

Control of flexible multibody systems, such as flexible manipulators, is a challenging task. This is especially true if end-effector trajectory tracking is aspired. On the one hand, these systems require a large number of generalized coordinates to describe their dynamical behavior accurately. On the other hand, only a small subset of these values can be measured or reconstructed on-the-fly. Hence, it is difficult, if not nearly impossible, to use a state controller. In addition, flexible systems are under actuated, i.e. they possess less control inputs than generalized coordinates. In case of a non-collocated output controller, which is the case for end-effector trajectory tracking, the closed loop of the system might lose passivity and is non-minimum phase. In order to achieve end-effector trajectory tracking, exact and approximate feed-forward controls can be applied. In this work, two different versions of such concepts are compared experimentally. These model-based concepts are computed off-line and they supply, next to the required input values, a C1 -continuous solution of the complete state vector which can be used for feedback control. If the system is non-minimum phase, a two-sided boundary value problem has to be solved and the solution includes a pre-actuation as well as a post-actuation phase. While the exact method incorporates all dynamical effects of the flexible multibody system, the approximate concepts neglect certain implications, for example the dynamical effects due to the flexibility. In addition to the presentation of the theoretical basics of the control approaches and the underlying models, this contribution addresses some of the crucial obstacles, which have to be overcome for the operation of the test bench, e.g., signal conditioning, state reconstruction and friction compensation. Since the installed sensors do not allow the direct measurement of the end effector position, image tracking is used to judge the quality of the different

Manipulation of nano-entities in suspension by electric fields

Science.gov (United States)

Fan, Donglei

Nanoscale entities, including nanospheres, nanodisks, nanorings, nanowires and nanotubes are potential building blocks for nanoscale devices. Among them, nanowires is an important type of nanoparticles, due to the potential application in microelectronics and bio-diagnosis. Manipulation of nanowires in suspension has been a formidable problem. As described in this thesis, using AC electric fields applied to strategically designed microelectrodes, nanowires in suspension can be driven to align, to chain, to accelerate in directions parallel and perpendicular to its orientation, to concentrate onto designated places, and to disperse in a controlled manner with high efficiency despite an extremely low Reynolds number at the level of 10-5. Randomly oriented nanowires in suspension can be rapidly assembled into extended nonlinear structures within seconds. We show that both the electric field and its gradient play the essential roles of aligning and transporting the nanowires into scaffolds according to the electric field distributions inherent to the geometry of the microelectrodes. The assembling efficiency depends strongly on the frequency of the applied AC voltages and varies as square of the voltage. Furthermore, nanowires have been rotated by AC electric fields applied to strategically designed electrodes. The rotation of the nanowires can be instantly switched on or off with precisely controlled rotation speed (to at least 25000 rpm), definite chirality, and total angle of rotation. This new method has been used to controllably rotate magnetic and non-magnetic nanowires as well as multi-wall carbon nanotubes. We have also produced a micromotor using a rotating nanowire that can drive particles into circular motion. This has application to microfluidic devices, micro-stirrers, and micro electromechanical systems (MEMS). To move and place nanowires onto designated locations with high precision, electrophoretic force has been combined with dielectrophoretic force to

High precision redundant robotic manipulator

International Nuclear Information System (INIS)

Young, K.K.D.

1998-01-01

A high precision redundant robotic manipulator for overcoming contents imposed by obstacles or imposed by a highly congested work space is disclosed. One embodiment of the manipulator has four degrees of freedom and another embodiment has seven degrees of freedom. Each of the embodiments utilize a first selective compliant assembly robot arm (SCARA) configuration to provide high stiffness in the vertical plane, a second SCARA configuration to provide high stiffness in the horizontal plane. The seven degree of freedom embodiment also utilizes kinematic redundancy to provide the capability of avoiding obstacles that lie between the base of the manipulator and the end effector or link of the manipulator. These additional three degrees of freedom are added at the wrist link of the manipulator to provide pitch, yaw and roll. The seven degrees of freedom embodiment uses one revolute point per degree of freedom. For each of the revolute joints, a harmonic gear coupled to an electric motor is introduced, and together with properly designed based servo controllers provide an end point repeatability of less than 10 microns. 3 figs

Bioprinting Living Biofilms through Optogenetic Manipulation.

Science.gov (United States)

Huang, Yajia; Xia, Aiguo; Yang, Guang; Jin, Fan

2018-04-18

In this paper, we present a new strategy for microprinting dense bacterial communities with a prescribed organization on a substrate. Unlike conventional bioprinting techniques that require bioinks, through optogenetic manipulation, we directly manipulated the behaviors of Pseudomonas aeruginosa to allow these living bacteria to autonomically form patterned biofilms following prescribed illumination. The results showed that through optogenetic manipulation, patterned bacterial communities with high spatial resolution (approximately 10 μm) could be constructed in 6 h. Thus, optogenetic manipulation greatly increases the range of available bioprinting techniques.

Master-slave-manipulator 'EMSM I'

International Nuclear Information System (INIS)

Koehler, G.W.; Salaske, M.

1976-01-01

A master-slave manipulator with electric force transmission and reflection was developed for the first time in the German Federal Republic. The apparatus belongs to the class of 200 N carrying capacity. It is intended mainly for nuclear purposes and especially for use in large hot cells and also for medium and heavy manipulator vehicles. The most innovations compared with previously known foreign electric master-slave manipulators are two additional possibilities of movement and the electric dead weight compensation. (orig.) [de

Master-slave-manipulator EMSM I

International Nuclear Information System (INIS)

Koehler, G.W.; Salaske, M.

1976-01-01

A master-slave manipulator with electric force transmission and reflection was developed for the first time in the German Federal Republic. The aparatus belongs to the class of 200 N carrying capacity. It is intended mainly for nuclear purposes and especially for use in large hot cells and also for medium and heavy manipulator vehicles. The most obvious innovations compared with previously known foreign electric master-slave manipulators are two additional possibilities of movement and the electric dead weightcompensation. (orig.) [de

Fast implementations of 3D PET reconstruction using vector and parallel programming techniques

International Nuclear Information System (INIS)

Guerrero, T.M.; Cherry, S.R.; Dahlbom, M.; Ricci, A.R.; Hoffman, E.J.

1993-01-01

Computationally intensive techniques that offer potential clinical use have arisen in nuclear medicine. Examples include iterative reconstruction, 3D PET data acquisition and reconstruction, and 3D image volume manipulation including image registration. One obstacle in achieving clinical acceptance of these techniques is the computational time required. This study focuses on methods to reduce the computation time for 3D PET reconstruction through the use of fast computer hardware, vector and parallel programming techniques, and algorithm optimization. The strengths and weaknesses of i860 microprocessor based workstation accelerator boards are investigated in implementations of 3D PET reconstruction

Parallel MR imaging.

Science.gov (United States)

Deshmane, Anagha; Gulani, Vikas; Griswold, Mark A; Seiberlich, Nicole

2012-07-01

Parallel imaging is a robust method for accelerating the acquisition of magnetic resonance imaging (MRI) data, and has made possible many new applications of MR imaging. Parallel imaging works by acquiring a reduced amount of k-space data with an array of receiver coils. These undersampled data can be acquired more quickly, but the undersampling leads to aliased images. One of several parallel imaging algorithms can then be used to reconstruct artifact-free images from either the aliased images (SENSE-type reconstruction) or from the undersampled data (GRAPPA-type reconstruction). The advantages of parallel imaging in a clinical setting include faster image acquisition, which can be used, for instance, to shorten breath-hold times resulting in fewer motion-corrupted examinations. In this article the basic concepts behind parallel imaging are introduced. The relationship between undersampling and aliasing is discussed and two commonly used parallel imaging methods, SENSE and GRAPPA, are explained in detail. Examples of artifacts arising from parallel imaging are shown and ways to detect and mitigate these artifacts are described. Finally, several current applications of parallel imaging are presented and recent advancements and promising research in parallel imaging are briefly reviewed. Copyright © 2012 Wiley Periodicals, Inc.

Using Manipulatives to Teach Elementary Mathematics

Science.gov (United States)

Boggan, Matthew; Harper, Sallie; Whitmire, Anna

2010-01-01

The purpose of this paper is to explain the importance and benefits of math manipulatives. For decades, the National Council of Teachers of Mathematics has encouraged school districts nationwide to use manipulatives in mathematical instruction. The value of manipulatives has been recognized for many years, but some teachers are reluctant to use…

High-Performance Psychometrics: The Parallel-E Parallel-M Algorithm for Generalized Latent Variable Models. Research Report. ETS RR-16-34

Science.gov (United States)

von Davier, Matthias

2016-01-01

This report presents results on a parallel implementation of the expectation-maximization (EM) algorithm for multidimensional latent variable models. The developments presented here are based on code that parallelizes both the E step and the M step of the parallel-E parallel-M algorithm. Examples presented in this report include item response…

Andreev reflection properties in a parallel mesoscopic circuit with Majorana bound states

Energy Technology Data Exchange (ETDEWEB)

Mu, Jin-Tao; Han, Yu [Physics Department, Liaoning University, Shenyang 110036 (China); Gong, Wei-Jiang, E-mail: gwj@mail.neu.edu.cn [College of Sciences, Northeastern University, Shenyang 110819 (China)

2017-03-15

We investigate the Andreev reflection in a parallel mesoscopic circuit with Majorana bound states (MBSs). It is found that in such a structure, the Andreev current can be manipulated in a highly efficient way, by the adjustment of bias voltage, dot levels, inter-MBS coupling, and the applied magnetic flux. Besides, the dot-MBS coupling manner is an important factor to modulate the Andreev current, because it influences the period of the conductance oscillation. By discussing the underlying quantum interference mechanism, the Andreev-reflection property is explained in detail. We believe that all the results can assist to understand the nontrivial role of the MBSs in driving the Andreev reflection.

Manipulating the Shape of Electronic Non-Dispersive Wave-Packets in the Hydrogen Atom: Numerical Tests in Realistic Experimental Conditions

International Nuclear Information System (INIS)

Delande, D.; Sacha, K.; Zakrzewski, J.

2002-01-01

We show that combination of a linearly polarized resonant microwave field and a parallel static electric field may be used to create a non-dispersive electronic wave packet in Rydberg atoms. The static electric field allows for manipulation of the shape of the elliptical trajectory the wave packet is propagating on. Exact quantum numerical calculations for realistic experimental parameters show that the wave packet evolving on a linear orbit can be very easily prepared in a laboratory either by a direct optical excitation or by preparing an atom in an extremal Stark state and then slowly switching on the micro wave field. The latter scheme seems to be very resistant to experimental imperfections. Once the wave packet on the linear orbit is excited, the static field may be used to manipulate the shape of the orbit. (author)

Effects of visual information regarding allocentric processing in haptic parallelity matching.

Science.gov (United States)

Van Mier, Hanneke I

2013-10-01

Research has revealed that haptic perception of parallelity deviates from physical reality. Large and systematic deviations have been found in haptic parallelity matching most likely due to the influence of the hand-centered egocentric reference frame. Providing information that increases the influence of allocentric processing has been shown to improve performance on haptic matching. In this study allocentric processing was stimulated by providing informative vision in haptic matching tasks that were performed using hand- and arm-centered reference frames. Twenty blindfolded participants (ten men, ten women) explored the orientation of a reference bar with the non-dominant hand and subsequently matched (task HP) or mirrored (task HM) its orientation on a test bar with the dominant hand. Visual information was provided by means of informative vision with participants having full view of the test bar, while the reference bar was blocked from their view (task VHP). To decrease the egocentric bias of the hands, participants also performed a visual haptic parallelity drawing task (task VHPD) using an arm-centered reference frame, by drawing the orientation of the reference bar. In all tasks, the distance between and orientation of the bars were manipulated. A significant effect of task was found; performance improved from task HP, to VHP to VHPD, and HM. Significant effects of distance were found in the first three tasks, whereas orientation and gender effects were only significant in tasks HP and VHP. The results showed that stimulating allocentric processing by means of informative vision and reducing the egocentric bias by using an arm-centered reference frame led to most accurate performance on parallelity matching. © 2013 Elsevier B.V. All rights reserved.

Parallel Algorithm of Geometrical Hashing Based on NumPy Package and Processes Pool

Directory of Open Access Journals (Sweden)

Klyachin Vladimir Aleksandrovich

2015-10-01

Full Text Available The article considers the problem of multi-dimensional geometric hashing. The paper describes a mathematical model of geometric hashing and considers an example of its use in localization problems for the point. A method of constructing the corresponding hash matrix by parallel algorithm is considered. In this paper an algorithm of parallel geometric hashing using a development pattern «pool processes» is proposed. The implementation of the algorithm is executed using the Python programming language and NumPy package for manipulating multidimensional data. To implement the process pool it is proposed to use a class Process Pool Executor imported from module concurrent.futures, which is included in the distribution of the interpreter Python since version 3.2. All the solutions are presented in the paper by corresponding UML class diagrams. Designed GeomNash package includes classes Data, Result, GeomHash, Job. The results of the developed program presents the corresponding graphs. Also, the article presents the theoretical justification for the application process pool for the implementation of parallel algorithms. It is obtained condition t2 > (p/(p-1*t1 of the appropriateness of process pool. Here t1 - the time of transmission unit of data between processes, and t2 - the time of processing unit data by one processor.

Nano-manipulation of single DNA molecules

International Nuclear Information System (INIS)

Hu Jun; Shanghai Jiaotong Univ., Shanghai; Lv Junhong; Wang Guohua; Wang Ying; Li Minqian; Zhang Yi; Li Bin; Li Haikuo; An Hongjie

2004-01-01

Nano-manipulation of single atoms and molecules is a critical technique in nanoscience and nanotechnology. This review paper will focus on the recent development of the manipulation of single DNA molecules based on atomic force microscopy (AFM). Precise manipulation has been realized including varied manipulating modes such as 'cutting', 'pushing', 'folding', 'kneading', 'picking up', 'dipping', etc. The cutting accuracy is dominated by the size of the AFM tip, which is usually 10 nm or less. Single DNA fragments can be cut and picked up and then amplified by single molecule PCR. Thus positioning isolation and sequencing can be performed. (authors)

Task based synthesis of serial manipulators

Directory of Open Access Journals (Sweden)

Sarosh Patel

2015-05-01

Full Text Available Computing the optimal geometric structure of manipulators is one of the most intricate problems in contemporary robot kinematics. Robotic manipulators are designed and built to perform certain predetermined tasks. There is a very close relationship between the structure of the manipulator and its kinematic performance. It is therefore important to incorporate such task requirements during the design and synthesis of the robotic manipulators. Such task requirements and performance constraints can be specified in terms of the required end-effector positions, orientations and velocities along the task trajectory. In this work, we present a comprehensive method to develop the optimal geometric structure (DH parameters of a non-redundant six degree of freedom serial manipulator from task descriptions. In this work we define, develop and test a methodology to design optimal manipulator configurations based on task descriptions. This methodology is devised to investigate all possible manipulator configurations that can satisfy the task performance requirements under imposed joint constraints. Out of all the possible structures, the structures that can reach all the task points with the required orientations are selected. Next, these candidate structures are tested to see whether they can attain end-effector velocities in arbitrary directions within the user defined joint constraints, so that they can deliver the best kinematic performance. Additionally least power consuming configurations are also identified.

Collision Detection for Underwater ROV Manipulator Systems

Directory of Open Access Journals (Sweden)

Satja Sivčev

2018-04-01

Full Text Available Work-class ROVs equipped with robotic manipulators are extensively used for subsea intervention operations. Manipulators are teleoperated by human pilots relying on visual feedback from the worksite. Operating in a remote environment, with limited pilot perception and poor visibility, manipulator collisions which may cause significant damage are likely to happen. This paper presents a real-time collision detection algorithm for marine robotic manipulation. The proposed collision detection mechanism is developed, integrated into a commercial ROV manipulator control system, and successfully evaluated in simulations and experimental setup using a real industry standard underwater manipulator. The presented collision sensing solution has a potential to be a useful pilot assisting tool that can reduce the task load, operational time, and costs of subsea inspection, repair, and maintenance operations.

A SPECT reconstruction method for extending parallel to non-parallel geometries

International Nuclear Information System (INIS)

Wen Junhai; Liang Zhengrong

2010-01-01

Due to its simplicity, parallel-beam geometry is usually assumed for the development of image reconstruction algorithms. The established reconstruction methodologies are then extended to fan-beam, cone-beam and other non-parallel geometries for practical application. This situation occurs for quantitative SPECT (single photon emission computed tomography) imaging in inverting the attenuated Radon transform. Novikov reported an explicit parallel-beam formula for the inversion of the attenuated Radon transform in 2000. Thereafter, a formula for fan-beam geometry was reported by Bukhgeim and Kazantsev (2002 Preprint N. 99 Sobolev Institute of Mathematics). At the same time, we presented a formula for varying focal-length fan-beam geometry. Sometimes, the reconstruction formula is so implicit that we cannot obtain the explicit reconstruction formula in the non-parallel geometries. In this work, we propose a unified reconstruction framework for extending parallel-beam geometry to any non-parallel geometry using ray-driven techniques. Studies by computer simulations demonstrated the accuracy of the presented unified reconstruction framework for extending parallel-beam to non-parallel geometries in inverting the attenuated Radon transform.

The language parallel Pascal and other aspects of the massively parallel processor

Science.gov (United States)

Reeves, A. P.; Bruner, J. D.

1982-01-01

A high level language for the Massively Parallel Processor (MPP) was designed. This language, called Parallel Pascal, is described in detail. A description of the language design, a description of the intermediate language, Parallel P-Code, and details for the MPP implementation are included. Formal descriptions of Parallel Pascal and Parallel P-Code are given. A compiler was developed which converts programs in Parallel Pascal into the intermediate Parallel P-Code language. The code generator to complete the compiler for the MPP is being developed independently. A Parallel Pascal to Pascal translator was also developed. The architecture design for a VLSI version of the MPP was completed with a description of fault tolerant interconnection networks. The memory arrangement aspects of the MPP are discussed and a survey of other high level languages is given.

Parallel Atomistic Simulations

Energy Technology Data Exchange (ETDEWEB)

HEFFELFINGER,GRANT S.

2000-01-18

Algorithms developed to enable the use of atomistic molecular simulation methods with parallel computers are reviewed. Methods appropriate for bonded as well as non-bonded (and charged) interactions are included. While strategies for obtaining parallel molecular simulations have been developed for the full variety of atomistic simulation methods, molecular dynamics and Monte Carlo have received the most attention. Three main types of parallel molecular dynamics simulations have been developed, the replicated data decomposition, the spatial decomposition, and the force decomposition. For Monte Carlo simulations, parallel algorithms have been developed which can be divided into two categories, those which require a modified Markov chain and those which do not. Parallel algorithms developed for other simulation methods such as Gibbs ensemble Monte Carlo, grand canonical molecular dynamics, and Monte Carlo methods for protein structure determination are also reviewed and issues such as how to measure parallel efficiency, especially in the case of parallel Monte Carlo algorithms with modified Markov chains are discussed.

Stainless steel decontamination manipulators

International Nuclear Information System (INIS)

Sullivan, R.J.

1986-01-01

Three, large-volume coverage manipulator systems were designed and built for the Defense Water Processing Facility at the Savannah River Laboratory. These stainless steel systems will be used for high-pressure spray decontamination of waste containers and large process equipment modules. Each system has a manipulator arm, folding boom, and vertical drive and guide structure. Handling capacity is 45 kg, horizontal reach is 4.6 m with a 180-deg swing motion, and the vertical travel is 6 m. The system is remotely removable and replaceable in modules using an overhead crane and an impact wrench. The manipulator arm has seven motions: Shoulder rotation and pivot, elbow pivot, wrist pivot and rotation, and grip open-close. All motions are variable speed and are slip-clutch protected to prevent overloading from external forces (collisions)

Modification of Method for Solution of Direct Kinematic Problem for the Type of Platform Manipulators with Six Degrees of Freedom

Directory of Open Access Journals (Sweden)

A. L. Lapikov

2014-01-01

Full Text Available This paper considers creation of methods for research of multi-section manipulators of parallel structure. To solve this task it is necessary, firstly, to carry out generalization, systematization, and enhancement of existing models of platform manipulators with six degrees of freedom; secondly, it is necessary to modify previously suggested methods for solving the kinematic tasks for the specified type of manipulation mechanisms. The paper presents detailed domain analysis, describes major issues appearing in the course of research, and suggests basic methods of their solution. The paper demonstrates the necessity for modification of existing models through supplementing new parameters. Modification and generalization of the previously suggested method for solution of direct kinematic problem for the specified type of manipulators were carried out. Method for solution of this problem consists in establishing the dependence of functional relationship of Cartesian coordinates and orientation of the moving platform center on the values of generalized coordinates of manipulator (in case of platform manipulators, these are the lengths of telescopic legs connecting the base and the moving platform of the manipulator. The method is created in such a way that solution of direct kinematic problem results in finding of the analytical equation of the plane where the moving platform lies. The equation of the required plane is described through three points (attachment points of the moving platform joints. To define coordinate values of the joints, the system of nine non-linear equations is generated. It should be noted that the system of equations is composed of one-type equations with the same type of nonlinearity. The physical meaning of all the nine equations of the system is Euclidean distance between the points of the manipulator. The location and orientation of the manipulator are depicted as a homogenous transformation matrix. Vectors of translation

3D Laser Scanner for Underwater Manipulation.

Science.gov (United States)

Palomer, Albert; Ridao, Pere; Youakim, Dina; Ribas, David; Forest, Josep; Petillot, Yvan

2018-04-04

Nowadays, research in autonomous underwater manipulation has demonstrated simple applications like picking an object from the sea floor, turning a valve or plugging and unplugging a connector. These are fairly simple tasks compared with those already demonstrated by the mobile robotics community, which include, among others, safe arm motion within areas populated with a priori unknown obstacles or the recognition and location of objects based on their 3D model to grasp them. Kinect-like 3D sensors have contributed significantly to the advance of mobile manipulation providing 3D sensing capabilities in real-time at low cost. Unfortunately, the underwater robotics community is lacking a 3D sensor with similar capabilities to provide rich 3D information of the work space. In this paper, we present a new underwater 3D laser scanner and demonstrate its capabilities for underwater manipulation. In order to use this sensor in conjunction with manipulators, a calibration method to find the relative position between the manipulator and the 3D laser scanner is presented. Then, two different advanced underwater manipulation tasks beyond the state of the art are demonstrated using two different manipulation systems. First, an eight Degrees of Freedom (DoF) fixed-base manipulator system is used to demonstrate arm motion within a work space populated with a priori unknown fixed obstacles. Next, an eight DoF free floating Underwater Vehicle-Manipulator System (UVMS) is used to autonomously grasp an object from the bottom of a water tank.

Massively Parallel Interrogation of Aptamer Sequence, Structure and Function

Energy Technology Data Exchange (ETDEWEB)

Fischer, N O; Tok, J B; Tarasow, T M

2008-02-08

Optimization of high affinity reagents is a significant bottleneck in medicine and the life sciences. The ability to synthetically create thousands of permutations of a lead high-affinity reagent and survey the properties of individual permutations in parallel could potentially relieve this bottleneck. Aptamers are single stranded oligonucleotides affinity reagents isolated by in vitro selection processes and as a class have been shown to bind a wide variety of target molecules. Methodology/Principal Findings. High density DNA microarray technology was used to synthesize, in situ, arrays of approximately 3,900 aptamer sequence permutations in triplicate. These sequences were interrogated on-chip for their ability to bind the fluorescently-labeled cognate target, immunoglobulin E, resulting in the parallel execution of thousands of experiments. Fluorescence intensity at each array feature was well resolved and shown to be a function of the sequence present. The data demonstrated high intra- and interchip correlation between the same features as well as among the sequence triplicates within a single array. Consistent with aptamer mediated IgE binding, fluorescence intensity correlated strongly with specific aptamer sequences and the concentration of IgE applied to the array. The massively parallel sequence-function analyses provided by this approach confirmed the importance of a consensus sequence found in all 21 of the original IgE aptamer sequences and support a common stem:loop structure as being the secondary structure underlying IgE binding. The microarray application, data and results presented illustrate an efficient, high information content approach to optimizing aptamer function. It also provides a foundation from which to better understand and manipulate this important class of high affinity biomolecules.

Massively parallel interrogation of aptamer sequence, structure and function.

Directory of Open Access Journals (Sweden)

Nicholas O Fischer

Full Text Available BACKGROUND: Optimization of high affinity reagents is a significant bottleneck in medicine and the life sciences. The ability to synthetically create thousands of permutations of a lead high-affinity reagent and survey the properties of individual permutations in parallel could potentially relieve this bottleneck. Aptamers are single stranded oligonucleotides affinity reagents isolated by in vitro selection processes and as a class have been shown to bind a wide variety of target molecules. METHODOLOGY/PRINCIPAL FINDINGS: High density DNA microarray technology was used to synthesize, in situ, arrays of approximately 3,900 aptamer sequence permutations in triplicate. These sequences were interrogated on-chip for their ability to bind the fluorescently-labeled cognate target, immunoglobulin E, resulting in the parallel execution of thousands of experiments. Fluorescence intensity at each array feature was well resolved and shown to be a function of the sequence present. The data demonstrated high intra- and inter-chip correlation between the same features as well as among the sequence triplicates within a single array. Consistent with aptamer mediated IgE binding, fluorescence intensity correlated strongly with specific aptamer sequences and the concentration of IgE applied to the array. CONCLUSION AND SIGNIFICANCE: The massively parallel sequence-function analyses provided by this approach confirmed the importance of a consensus sequence found in all 21 of the original IgE aptamer sequences and support a common stem:loop structure as being the secondary structure underlying IgE binding. The microarray application, data and results presented illustrate an efficient, high information content approach to optimizing aptamer function. It also provides a foundation from which to better understand and manipulate this important class of high affinity biomolecules.

Manipulating Strings in Python

Directory of Open Access Journals (Sweden)

William J. Turkel

2012-07-01

Full Text Available This lesson is a brief introduction to string manipulation techniques in Python. Knowing how to manipulate strings plays a crucial role in most text processing tasks. If you’d like to experiment with the following lessons, you can write and execute short programs as we’ve been doing, or you can open up a Python shell / Terminal to try them out on the command line.

System Integration for Real-time Mobile Manipulation

OpenAIRE

Oftadeh, Reza; Aref, Mohammad M.; Ghabcheloo, Reza; Mattila, Jouni

2014-01-01

Mobile manipulators are one of the most complicated types of mechatronics systems. The performance of these robots in performing complex manipulation tasks is highly correlated with the synchronization and integration of their low-level components. This paper discusses in detail the mechatronics design of a four wheel steered mobile manipulator. It presents the manipulator ’s mechanical structure and electrical interfaces, designs low-level software architecture based on embedded PC-based con...

Modeling manipulation in medical education.

Science.gov (United States)

Dailey, Jason I

2010-05-01

As residents and medical students progress through their medical training, they are presented with multiple instances in which they feel they must manipulate the healthcare system and deceive others in order to efficiently treat their patients. This, however, creates a culture of manipulation resulting in untoward effects on trainees' ethical and professional development. Yet manipulation need not be a skill necessary to practice medicine, and steps should be taken by both individuals and institutions to combat the view that the way medicine must be practiced "in the real world" is somehow different from what one's affective moral sense implores.

Parallel integer sorting with medium and fine-scale parallelism

Science.gov (United States)

Dagum, Leonardo

1993-01-01

Two new parallel integer sorting algorithms, queue-sort and barrel-sort, are presented and analyzed in detail. These algorithms do not have optimal parallel complexity, yet they show very good performance in practice. Queue-sort designed for fine-scale parallel architectures which allow the queueing of multiple messages to the same destination. Barrel-sort is designed for medium-scale parallel architectures with a high message passing overhead. The performance results from the implementation of queue-sort on a Connection Machine CM-2 and barrel-sort on a 128 processor iPSC/860 are given. The two implementations are found to be comparable in performance but not as good as a fully vectorized bucket sort on the Cray YMP.

Professional responsibility in relation to cervical spine manipulation.

Science.gov (United States)

Refshauge, Kathryn M; Parry, Sharon; Shirley, Debra; Larsen, Dale; Rivett, Darren A; Boland, Rob

2002-01-01

Manipulation of the cervical spine is one of the few potentially life-threatening procedures performed by physiotherapists. Is it worth the risk? A comparison of risks versus benefits indicates that at present, the risks of cervical manipulation outweigh the benefits: manipulation has yet to be shown to be more effective for neck pain and headache than other interventions such as mobilisation, whereas the risks, although infrequent, are serious. This analysis is of particular concern because the conditions for which manipulation is indicated are benign and usually self-limiting. Because physiotherapists have legal and ethical obligations to the community to avoid foreseeable harm and provide optimum care, it may be prudent to determine who in our profession should perform cervical manipulation. That is, the profession could restrict the practice of cervical spine manipulation. Although all registered physiotherapists in Australia are entitled to perform cervical manipulation, few choose to use this intervention. Therefore, it might be feasible to encourage those practitioners who wish to use cervical manipulation to undertake formal education programs. Such a requirement could be embodied in a code of practice that discourages those without formal training from performing cervical manipulation. By taking such measures, we could ensure that our profession exercises wisdom in its monitoring and use of cervical manipulation.

An Analysis of Manipulation Strategies in Stock Markets

OpenAIRE

Rasim Ozcan

2012-01-01

Manipulative transactions, which affect both the supply and demand side of the markets, have been studied by academic circles and it was concluded that manipulation exerts negative impact on markets. A market with manipulation is considered as less trustworthy and credible compared to a market without manipulation, which in turn, affects demand. Manipulations affecting both the supply and demand should be closely monitored by stock market investors as well as legislative, executive, and regul...

The Anatomy of Virtual Manipulative Apps: Using Grounded Theory to Conceptualize and Evaluate Educational Apps that Contain Virtual Manipulatives

OpenAIRE

Boyer-Thurgood, Jennifer M.

2017-01-01

This exploratory qualitative study used grounded theory to investigate the anatomy of educational apps that contain virtual manipulatives. For this study 100 virtual manipulatives within educational apps designed for the iPad were observed by the researcher in order to expand the explanations of and build theory about virtual manipulatives within apps. Affordance theory was used to frame all six phases of the study in which the researcher identified virtual manipulatives situated within educa...

About Parallel Programming: Paradigms, Parallel Execution and Collaborative Systems

Directory of Open Access Journals (Sweden)

Loredana MOCEAN

2009-01-01

Full Text Available In the last years, there were made efforts for delineation of a stabile and unitary frame, where the problems of logical parallel processing must find solutions at least at the level of imperative languages. The results obtained by now are not at the level of the made efforts. This paper wants to be a little contribution at these efforts. We propose an overview in parallel programming, parallel execution and collaborative systems.

Probabilistic approach to manipulator kinematics and dynamics

International Nuclear Information System (INIS)

Rao, S.S.; Bhatti, P.K.

2001-01-01

A high performance, high speed robotic arm must be able to manipulate objects with a high degree of accuracy and repeatability. As with any other physical system, there are a number of factors causing uncertainties in the behavior of a robotic manipulator. These factors include manufacturing and assembling tolerances, and errors in the joint actuators and controllers. In order to study the effect of these uncertainties on the robotic end-effector and to obtain a better insight into the manipulator behavior, the manipulator kinematics and dynamics are modeled using a probabilistic approach. Based on the probabilistic model, kinematic and dynamic performance criteria are defined to provide measures of the behavior of the robotic end-effector. Techniques are presented to compute the kinematic and dynamic reliabilities of the manipulator. The effects of tolerances associated with the various manipulator parameters on the reliabilities are studied. Numerical examples are presented to illustrate the procedures

Parallel computing works!

CERN Document Server

Fox, Geoffrey C; Messina, Guiseppe C

2014-01-01

A clear illustration of how parallel computers can be successfully appliedto large-scale scientific computations. This book demonstrates how avariety of applications in physics, biology, mathematics and other scienceswere implemented on real parallel computers to produce new scientificresults. It investigates issues of fine-grained parallelism relevant forfuture supercomputers with particular emphasis on hypercube architecture. The authors describe how they used an experimental approach to configuredifferent massively parallel machines, design and implement basic systemsoftware, and develop

3D Laser Scanner for Underwater Manipulation

Directory of Open Access Journals (Sweden)

Albert Palomer

2018-04-01

Full Text Available Nowadays, research in autonomous underwater manipulation has demonstrated simple applications like picking an object from the sea floor, turning a valve or plugging and unplugging a connector. These are fairly simple tasks compared with those already demonstrated by the mobile robotics community, which include, among others, safe arm motion within areas populated with a priori unknown obstacles or the recognition and location of objects based on their 3D model to grasp them. Kinect-like 3D sensors have contributed significantly to the advance of mobile manipulation providing 3D sensing capabilities in real-time at low cost. Unfortunately, the underwater robotics community is lacking a 3D sensor with similar capabilities to provide rich 3D information of the work space. In this paper, we present a new underwater 3D laser scanner and demonstrate its capabilities for underwater manipulation. In order to use this sensor in conjunction with manipulators, a calibration method to find the relative position between the manipulator and the 3D laser scanner is presented. Then, two different advanced underwater manipulation tasks beyond the state of the art are demonstrated using two different manipulation systems. First, an eight Degrees of Freedom (DoF fixed-base manipulator system is used to demonstrate arm motion within a work space populated with a priori unknown fixed obstacles. Next, an eight DoF free floating Underwater Vehicle-Manipulator System (UVMS is used to autonomously grasp an object from the bottom of a water tank.

A portable modular architecture for robotic manipulator control

International Nuclear Information System (INIS)

Butler, P.L.

1993-01-01

A control architecture has been developed to provide a framework for robotic manipulator control. This architecture, called the Modular Integrated Control Architecture (MICA), has been successfully applied to two different manipulator systems. MICA is a portable system in two respects. First, it can be used for the control of different types of manipulator systems. Second, the MICA code is portable across several operating environments. This portability allows the sharing of common control code among various systems. A major portion of MICA is the precise control of multiple processors that have to be coordinated to control a manipulator system. By having NUCA control the processor synchronization, the system developer can concentrate on the specific aspects of a new manipulator system. MICA also provides standard functions for trajectory generation that can be used for most manipulators. Custom trajectory generators can be easily added to suit the needs of a particular robotic control system. Another facility that MICA provides is a simulation of the manipulator, allowing the control code to be simulated before trying it on a manipulator system. Using this technique, one can develop code for a manipulator system without risking damage to the arm during development

Managerial Incentives and Stock Price Manipulation

OpenAIRE

Peng, Lin; Röell, Ailsa A

2009-01-01

This paper presents a rational expectations model of optimal executive compensation in a setting where managers are in a position to manipulate short-term stock prices, and managers' propensity to manipulate is uncertain. Stock-based incentives elicit not only productive effort, but also costly information manipulation. We analyze the tradeoffs involved in conditioning pay on long- versus short-term performance and characterize a second-best optimal compensation scheme. The paper shows manipu...

Parallel optical control of spatiotemporal neuronal spike activity using high-frequency digital light processingtechnology

Directory of Open Access Journals (Sweden)

Jason eJerome

2011-08-01

Full Text Available Neurons in the mammalian neocortex receive inputs from and communicate back to thousands of other neurons, creating complex spatiotemporal activity patterns. The experimental investigation of these parallel dynamic interactions has been limited due to the technical challenges of monitoring or manipulating neuronal activity at that level of complexity. Here we describe a new massively parallel photostimulation system that can be used to control action potential firing in in vitro brain slices with high spatial and temporal resolution while performing extracellular or intracellular electrophysiological measurements. The system uses Digital-Light-Processing (DLP technology to generate 2-dimensional (2D stimulus patterns with >780,000 independently controlled photostimulation sites that operate at high spatial (5.4 µm and temporal (>13kHz resolution. Light is projected through the quartz-glass bottom of the perfusion chamber providing access to a large area (2.76 x 2.07 mm2 of the slice preparation. This system has the unique capability to induce temporally precise action potential firing in large groups of neurons distributed over a wide area covering several cortical columns. Parallel photostimulation opens up new opportunities for the in vitro experimental investigation of spatiotemporal neuronal interactions at a broad range of anatomical scales.

A links manipulator simulation program interim report

International Nuclear Information System (INIS)

Noble, R.A.

1987-04-01

A computer program to simulate the performance of the Heysham II rail-following manipulator has been developed. The program is being used to develop and test the rail-following control algorithms which will be used to control movements of the manipulator when it is operating below the gas baffle dome. The simulation includes the dynamic responses of the manipulator joint drives, excluding friction, backlash and compliance. It also includes full details of the manipulator's geometry. A method is given whereby the actual manipulator dynamics can be written into the program once these have been established by measurement. The program is written in FORTRAN and runs on a Perkin-Elmer 3220 mini-computer. The simulation program responds to velocity demands on the individual joints. These will normally come from the control program, in which they will be manually controlled by a joystick. A sigma 5664 colour graphics generator is programmed to display the current position of the manipulator. (UK)

Manipulators

International Nuclear Information System (INIS)

Andre, Y.; Routelous, F.; Spina, G.; Perpina, J.; Suquet, J.; Rossi, M.; Zanca, M.; Billiet, A.; Madec, L.; Lemoine, T.; Gaboriaud, G.; Aubert, B.; Rosenwald, J.C.; Neuenschwander, S.; Brisse, H.; Rehel, J.L.; Rebibo, G.; Bensimon, J.L.; Kulski, A.; Serhal, M.; Nguyen, K.V.; Lescure, R.; Cymbalista, M.

2005-01-01

Three articles have for purpose the radiation doses optimization in medical imaging. The first one concerns the radiation protection of manipulators working at a PET scan post, the second one concerns more particularly the optimization of doses delivered in pediatric computerized tomography, the third one is devoted to a comparison between radiation dose and image quality through scanners of adult temporal bone. (N.C.)

Managing collaboration in the nanoManipulator

DEFF Research Database (Denmark)

Hudson, Thomas C.; Heiser, Aron T.; Sonnenwald, Diane H.

2003-01-01

We designed, developed, deployed, and evaluated the Collaborative nanoManipulator (CnM), a system supporting remote collaboration between users of the nanoManipulator interface to atomic force microscopes. To be accepted by users, the shared nanoManipulator application had to have the same high...... level of interactivity as the single user system and the application had to support a user's ability to interleave working privately and working collaboratively. This paper briefly describes the entire collaboration system, but focuses on the shared nanoManipulator application. Based on our experience...... developing the CnM, we present: a method of analyzing applications to characterize the requirements for sharing data between collaborating sites, examples of data structures that support collaboration, and guidelines for selecting appropriate synchronization and concurrency control schemes....

Positional control of space robot manipulator

Science.gov (United States)

Kurochkin, Vladislav; Shymanchuk, Dzmitry

2018-05-01

In this article the mathematical model of a planar space robot manipulator is under study. The space robot manipulator represents a solid body with attached manipulators. The system of equations of motion is determined using the Lagrange's equations. The control problem concerning moving the robot to a given point and return it to a given trajectory in the phase space is solved. Changes of generalized coordinates and necessary control actions are plotted for a specific model.

A Research on the Primary Mirror Manipulator of Large Segmented-mirror Telescope

Science.gov (United States)

Zuo, H.

2012-09-01

Since Galileo firstly used the telescope to observe the sky 400 years ago, the aperture of the telescope has become larger and larger to observe the deeper universe, and the segmented-mirror telescope is becoming more and more popular with increasing aperture. In the early 21st century, a series of segmented-mirror telescopes have been constructed including the Large Sky Area Multi-object Fiber Spectroscopic Telescope (LAMOST) of China. LAMOST is a meridian reflecting Schmidt telescope, and the dimension of the primary mirror is about 6.7 m× 6 m, which is composed of 37 hexagonal sub-mirrors. However, a problem about the mirror installation appears with the increasing aperture. If there are hundreds of sub-mirrors in the telescope, it is a challenging job to mount and dismount them to the truss. This problem is discussed in this paper and a manipulator for the primary mirror of LAMOST is designed to perform the mount and dismount work. In chapter 1, all the segmented-mirror telescopes in the world are introduced and how the sub-mirrors of these telescopes are installed has been investigated. After comparing with the serial and the parallel robot, a serial robot manipulator proposal, which has several redundant degrees of freedom (DOFs), has been chosen from a series of design proposals. In chapter 2, the theoretical analysis has been carried out on the basis of the design proposal, which includes the forward kinematics and the inverse kinematics. Firstly the D-H coordinate is built according to the structure of the manipulator, so it is possible to obtain the end-effector position and orientation from the individual joint motion thanks to the forward kinematics. Because of the redundant DOFs of the manipulator, the inverse kinematics solution can be a very trick task, and the result may not be only, therefore a kind of simulation is carried out to get the numerical solution using ADAMS (Automatic Dynamic Analysis of Mechanical System). In the dynamics analysis the

Endpoint-based parallel data processing in a parallel active messaging interface of a parallel computer

Science.gov (United States)

Archer, Charles J.; Blocksome, Michael A.; Ratterman, Joseph D.; Smith, Brian E.

2014-08-12

Endpoint-based parallel data processing in a parallel active messaging interface (`PAMI`) of a parallel computer, the PAMI composed of data communications endpoints, each endpoint including a specification of data communications parameters for a thread of execution on a compute node, including specifications of a client, a context, and a task, the compute nodes coupled for data communications through the PAMI, including establishing a data communications geometry, the geometry specifying, for tasks representing processes of execution of the parallel application, a set of endpoints that are used in collective operations of the PAMI including a plurality of endpoints for one of the tasks; receiving in endpoints of the geometry an instruction for a collective operation; and executing the instruction for a collective operation through the endpoints in dependence upon the geometry, including dividing data communications operations among the plurality of endpoints for one of the tasks.

Dynamic Model of Platform Manipulator with Six Degrees of Freedom

Directory of Open Access Journals (Sweden)

A. L. Lapikov

2015-01-01

multisectional manipulator with a parallel structure.

Better with Byzantine: Manipulation-Optimal Mechanisms

Science.gov (United States)

Othman, Abraham; Sandholm, Tuomas

A mechanism is manipulable if it is in some agents’ best interest to misrepresent their private information. The revelation principle establishes that, roughly, anything that can be accomplished by a manipulable mechanism can also be accomplished with a truthful mechanism. Yet agents often fail to play their optimal manipulations due to computational limitations or various flavors of incompetence and cognitive biases. Thus, manipulable mechanisms in particular should anticipate byzantine play. We study manipulation-optimal mechanisms: mechanisms that are undominated by truthful mechanisms when agents act fully rationally, and do better than any truthful mechanism if any agent fails to act rationally in any way. This enables the mechanism designer to do better than the revelation principle would suggest, and obviates the need to predict byzantine agents’ irrational behavior. We prove a host of possibility and impossibility results for the concept which have the impression of broadly limiting possibility. These results are largely in line with the revelation principle, although the considerations are more subtle and the impossibility not universal.

The TFTR maintenance manipulator

International Nuclear Information System (INIS)

Kungl, D.; Loesser, D.; Heitzenroeder, P.; Cerdan, G.

1989-01-01

TFTR plans to begin D-T experiments in mid 1990. The D-T experimental program will produce approximately one hundred shots, with a neutron generation rate of 10 19 neutrons per shot. This will result in high levels of activation in TFTR, especially in the vacuum vessel. The primary purpose of the Maintenance Manipulator is to provide a means of remotely performing certain defined maintenance and inspection tasks inside the vacuum torus so as to minimize personnel exposure to radiation. The manipulator consists of a six-link folding boom connected to a fixed boom on a movable carriage. The entire manipulator is housed in a vacuum antechamber connected to the vacuum torus, through a port formerly used for a vacuum pumping duct. The configuration extends 180 0 in either direction to provide complete coverage of the torus. The four 3500 l/s turbopumps which were formerly used in the pumping duct will be mounted on the antechamber. The manipulator will utilize two end effectors. The first, called a General Inspection Arm (GIA) provides a movable platform to an inspection camera and an in-vacuum leak detector. The second is a bilateral, force-reflecting pair of slave arms which utilize specially developed tools to perform several maintenance functions. All components except the slave arms are capable of operating in TFTR's vacuum environment and during 150 0 C bakeout of the torus. (orig.)

MANIPULATING CONSUMERS THROUGH ADVERTISING

Directory of Open Access Journals (Sweden)

Nicoleta -Andreea Neacşu

2012-12-01

Full Text Available Marketing communication has evolved steadily in the direction of increasing complexity and increasing volume of funds needed to run their own actions. More than ever, consumers are exposed to an overwhelming variety of sources and communication tehniques, the information received being numerous, diverse and polyvalent. The desire to make more efficient the marketing communication activity urges the broadcasters to encode messages, to use effective means of propagation in order to obtain a high degree of control on receptors and to influence the consumption attitudes. Between the means used for this purpose, manipulation tehniques are well known. This paper highlights the main conclusions drawn as a result of a quantitative marketing research on the adult population from Braşov in order to identify the attitudes and opinions of consumers from Braşov regarding the manipulation techniques used by commercial practices and advertising.The results of the research have shown that 82% of the respondents buy products in promotional offers, and 18% choose not to buy these products and 61% of the respondents consider that they have not been manipulated not even once, while only 39% believe that they have been manipulated at least once through advertising or commercial practices. Advertisements on TV have a strong influence on consumers, 81% of the respondents considering that at least once they have bought a product because of a TV commercial.

Interaction control of a redundant mobile manipulator

International Nuclear Information System (INIS)

Chung, J.H.; Velinsky, S.A.; Hess, R.A.

1998-01-01

This paper discusses the modeling and control of a spatial mobile manipulator that consists of a robotic manipulator mounted on a wheeled mobile platform. The Lagrange-d'Alembert formulation is used to obtain a concise description of the dynamics of the system, which is subject to nonholonomic constraints. The complexity of the model is increased by introducing kinematic redundancy, which is created when a multilinked manipulator is used. The kinematic redundancy is resolved by decomposing the mobile manipulator into two subsystems: the mobile platform and the manipulator. The redundancy resolution scheme employs a nonlinear interaction-control algorithm, which is developed and applied to coordinate the two subsystems' controllers. The subsystem controllers are independently designed, based on each subsystem's dynamic characteristics. Simulation results show the promise of the developed algorithm

On stiffening cables of a long reach manipulator

International Nuclear Information System (INIS)

Wang, S.L.; Santiago, P.

1996-01-01

A long reach manipulator will be used for waste remediation in large underground storage tanks. The manipulator's slenderness makes it flexible and difficult to control. A low-cost and effective method to enhance the manipulator's stiffness is proposed in this research by using suspension cables. These cables can also be used to accurately measure the position of the manipulator's wrist

Manipulation Robustness of Collaborative Filtering

OpenAIRE

Benjamin Van Roy; Xiang Yan

2010-01-01

A collaborative filtering system recommends to users products that similar users like. Collaborative filtering systems influence purchase decisions and hence have become targets of manipulation by unscrupulous vendors. We demonstrate that nearest neighbors algorithms, which are widely used in commercial systems, are highly susceptible to manipulation and introduce new collaborative filtering algorithms that are relatively robust.

Comparative analysis of hydraulic crane-manipulating installations transport and technological machines and industrial robots hydraulic manipulators

Directory of Open Access Journals (Sweden)

Lagerev I.A.

2016-09-01

Full Text Available The article presents results of comparative analysis of hydraulic crane-manipulator installations of mobile transport and technological machines and hydraulic manipulators of industrial robots. The comparative analysis is based on consid-eration of a wide range of types and sizes indicated technical devices of both domestic and foreign production: 1580 structures of cranes and more than 450 structures of industrial robots. It was performed in the following areas: func-tional purpose and basic technical characteristics; a design; the loading conditions of the model and failures in operation process; approaches to the design, calculation methods and mathematical modeling. The conclusions about the degree of similarity and the degree of difference hydraulic crane-manipulator installations of transport and technological ma-chines and hydraulic industrial robot manipulators from the standpoint of their design and modeling occurring in them during operation of dynamic and structural processes.

Atomic and molecular manipulation

CERN Document Server

Mayne, Andrew J

2011-01-01

Work with individual atoms and molecules aims to demonstrate that miniaturized electronic, optical, magnetic, and mechanical devices can operate ultimately even at the level of a single atom or molecule. As such, atomic and molecular manipulation has played an emblematic role in the development of the field of nanoscience. New methods based on the use of the scanning tunnelling microscope (STM) have been developed to characterize and manipulate all the degrees of freedom of individual atoms and molecules with an unprecedented precision. In the meantime, new concepts have emerged to design molecules and substrates having specific optical, mechanical and electronic functions, thus opening the way to the fabrication of real nano-machines. Manipulation of individual atoms and molecules has also opened up completely new areas of research and knowledge, raising fundamental questions of "Optics at the atomic scale", "Mechanics at the atomic scale", Electronics at the atomic scale", "Quantum physics at the atomic sca...

Parallel phase model : a programming model for high-end parallel machines with manycores.

Energy Technology Data Exchange (ETDEWEB)

Wu, Junfeng (Syracuse University, Syracuse, NY); Wen, Zhaofang; Heroux, Michael Allen; Brightwell, Ronald Brian

2009-04-01

This paper presents a parallel programming model, Parallel Phase Model (PPM), for next-generation high-end parallel machines based on a distributed memory architecture consisting of a networked cluster of nodes with a large number of cores on each node. PPM has a unified high-level programming abstraction that facilitates the design and implementation of parallel algorithms to exploit both the parallelism of the many cores and the parallelism at the cluster level. The programming abstraction will be suitable for expressing both fine-grained and coarse-grained parallelism. It includes a few high-level parallel programming language constructs that can be added as an extension to an existing (sequential or parallel) programming language such as C; and the implementation of PPM also includes a light-weight runtime library that runs on top of an existing network communication software layer (e.g. MPI). Design philosophy of PPM and details of the programming abstraction are also presented. Several unstructured applications that inherently require high-volume random fine-grained data accesses have been implemented in PPM with very promising results.

Systematic approach for deriving feasible mappings of parallel algorithms to parallel computing platforms

NARCIS (Netherlands)

Arkin, Ethem; Tekinerdogan, Bedir; Imre, Kayhan M.

2017-01-01

The need for high-performance computing together with the increasing trend from single processor to parallel computer architectures has leveraged the adoption of parallel computing. To benefit from parallel computing power, usually parallel algorithms are defined that can be mapped and executed

Dynamic whole-body robotic manipulation

Science.gov (United States)

Abe, Yeuhi; Stephens, Benjamin; Murphy, Michael P.; Rizzi, Alfred A.

2013-05-01

The creation of dynamic manipulation behaviors for high degree of freedom, mobile robots will allow them to accomplish increasingly difficult tasks in the field. We are investigating how the coordinated use of the body, legs, and integrated manipulator, on a mobile robot, can improve the strength, velocity, and workspace when handling heavy objects. We envision that such a capability would aid in a search and rescue scenario when clearing obstacles from a path or searching a rubble pile quickly. Manipulating heavy objects is especially challenging because the dynamic forces are high and a legged system must coordinate all its degrees of freedom to accomplish tasks while maintaining balance. To accomplish these types of manipulation tasks, we use trajectory optimization techniques to generate feasible open-loop behaviors for our 28 dof quadruped robot (BigDog) by planning trajectories in a 13 dimensional space. We apply the Covariance Matrix Adaptation (CMA) algorithm to solve for trajectories that optimize task performance while also obeying important constraints such as torque and velocity limits, kinematic limits, and center of pressure location. These open-loop behaviors are then used to generate desired feed-forward body forces and foot step locations, which enable tracking on the robot. Some hardware results for cinderblock throwing are demonstrated on the BigDog quadruped platform augmented with a human-arm-like manipulator. The results are analogous to how a human athlete maximizes distance in the discus event by performing a precise sequence of choreographed steps.

Parallel algorithms

CERN Document Server

Casanova, Henri; Robert, Yves

2008-01-01

""…The authors of the present book, who have extensive credentials in both research and instruction in the area of parallelism, present a sound, principled treatment of parallel algorithms. … This book is very well written and extremely well designed from an instructional point of view. … The authors have created an instructive and fascinating text. The book will serve researchers as well as instructors who need a solid, readable text for a course on parallelism in computing. Indeed, for anyone who wants an understandable text from which to acquire a current, rigorous, and broad vi

Data manipulation with R

CERN Document Server

Abedin, Jaynal

2014-01-01

This book is a step-by step, example-oriented tutorial that will show both intermediate and advanced users how data manipulation is facilitated smoothly using R.This book is aimed at intermediate to advanced level users of R who want to perform data manipulation with R, and those who want to clean and aggregate data effectively. Readers are expected to have at least an introductory knowledge of R and some basic administration work in R, such as installing packages and calling them when required.

Improved dynamic equations for the generally configured Stewart platform manipulator

International Nuclear Information System (INIS)

Pedrammehr, Siamak; Mahboubkhah, Mehran; Khani, Navid

2012-01-01

In this paper, a Newton-Euler approach is utilized to generate the improved dynamic equations of the generally configured Stewart platform. Using the kinematic model of the universal joint, the rotational degree of freedom of the pods around the axial direction is taken into account in the formulation. The justifiable direction of the reaction moment on each pod is specified and considered in deriving the dynamic equations. Considering the theorem of parallel axes, the inertia tensors for different elements of the manipulator are obtained in this study. From a theoretical point, the improved formulation is more accurate in comparison with previous ones, and the necessity of the improvement is clear evident from significant differences in the simulation results for the improved model and the model without improvement. In addition to more feasibility of the structure and higher accuracy, the model is highly compatible with computer arithmetic and suitable for online applications for loop control problems in hardware

Spin-orbit torques for current parallel and perpendicular to a domain wall

International Nuclear Information System (INIS)

Schulz, Tomek; Lee, Kyujoon; Karnad, Gurucharan V.; Alejos, Oscar; Martinez, Eduardo; Moretti, Simone; Hals, Kjetil M. D.; Garcia, Karin; Ravelosona, Dafiné; Vila, Laurent; Lo Conte, Roberto; Kläui, Mathias; Ocker, Berthold; Brataas, Arne

2015-01-01

We report field- and current-induced domain wall (DW) depinning experiments in Ta\\Co 20 Fe 60 B 20 \\MgO nanowires through a Hall cross geometry. While purely field-induced depinning shows no angular dependence on in-plane fields, the effect of the current depends crucially on the internal DW structure, which we manipulate by an external magnetic in-plane field. We show depinning measurements for a current sent parallel to the DW and compare its depinning efficiency with the conventional case of current flowing perpendicularly to the DW. We find that the maximum efficiency is similar for both current directions within the error bars, which is in line with a dominating damping-like spin-orbit torque (SOT) and indicates that no large additional torques arise for currents perpendicular to the DW. Finally, we find a varying dependence of the maximum depinning efficiency angle for different DWs and pinning levels. This emphasizes the importance of our full angular scans compared with previously used measurements for just two field directions (parallel and perpendicular to the DW) to determine the real torque strength and shows the sensitivity of the SOT to the precise DW structure and pinning sites

Stock Market Manipulation on the Hong Kong Stock Exchange

Directory of Open Access Journals (Sweden)

Dionigi Gerace

2014-10-01

Full Text Available This study is the first to empirically examine stock market manipulation on the Hong Kong Stock Exchange. The dataset contains 40 cases of market manipulation from 1996 to 2009 that were successfully prosecuted by the Hong Kong Securities & Futures Commission. Manipulation is found to negatively impact market efficiency measures such as the bid-ask spread and volatility. Markets appear incapable of efficiently responding to the presence of manipulators and are characterised by information asymmetry. Manipulators were successfully able to raise prices and exit the market. This finding contradicts views that trade-based manipulation is entirely unprofitable and self-deterring. The victimisation of information-seeking investors and the market as a whole provides a strong rationale for all jurisdictions, including Australia, to have effective laws that prohibit manipulation and for robust enforcement of those laws to further deter market manipulation.

Managing collaboration in the nanoManipulator

DEFF Research Database (Denmark)

Hudson, Thomas C.; Helser, Aren T.; Sonnenwald, Diane H.

2004-01-01

We designed, developed, deployed, and evaluated the Collaborative nanoManipulator (CnM), a distributed, collaborative virtual environment system supporting remote scientific collaboration between users of the nanoManipulator interface to atomic force microscopes. This paper describes the entire...

Tension Stiffened and Tendon Actuated Manipulator

Science.gov (United States)

Doggett, William R. (Inventor); Dorsey, John T. (Inventor); Ganoe, George G. (Inventor); King, Bruce D. (Inventor); Jones, Thomas C. (Inventor); Mercer, Charles D. (Inventor); Corbin, Cole K. (Inventor)

2015-01-01

A tension stiffened and tendon actuated manipulator is provided performing robotic-like movements when acquiring a payload. The manipulator design can be adapted for use in-space, lunar or other planetary installations as it is readily configurable for acquiring and precisely manipulating a payload in both a zero-g environment and in an environment with a gravity field. The manipulator includes a plurality of link arms, a hinge connecting adjacent link arms together to allow the adjacent link arms to rotate relative to each other and a cable actuation and tensioning system provided between adjacent link arms. The cable actuation and tensioning system includes a spreader arm and a plurality of driven and non-driven elements attached to the link arms and the spreader arm. At least one cable is routed around the driven and non-driven elements for actuating the hinge.

A New XYZ Compliant Parallel Mechanism for Micro-/Nano-Manipulation: Design and Analysis

Directory of Open Access Journals (Sweden)

Haiyang Li

2016-02-01

Full Text Available Based on the constraint and position identification (CPI approach for synthesizing XYZ compliant parallel mechanisms (CPMs and configuration modifications, this paper proposes a new fully-symmetrical XYZ CPM with desired motion characteristics such as reduced cross-axis coupling, minimized lost motion, and relatively small parasitic motion. The good motion characteristics arise from not only its symmetric configuration, but also the rigid linkages between non-adjacent rigid stages. Comprehensive kinematic analysis is carried out based on a series of finite element simulations over a motion range per axis less than ±5% of the beam length, which reveals that the maximum cross-axis coupling rate is less than 0.86%, the maximum lost motion rate is less than 1.20%, the parasitic rotations of the motion stage (MS are in the order of 10−5 rad, and the parasitic translations of the three actuated stages (ASs are in the order of 10−4 of the beam length (less than 0.3% of the motion range, where the beam slenderness ratio is larger than 20. Furthermore, the nonlinear analytical models of the primary translations of the XYZ CPM, including the primary translations of the MS and the ASs, are derived and validated to provide a quick design synthesis. Moreover, two practical design schemes of the proposed XYZ CPM are discussed with consideration of the manufacturability. The practical designs enable the XYZ CPM to be employed in many applications such as micro-/nano-positioning, micro-/nano-manufacturing and micro-/nano-assembly. Finally, a spatial high-precision translational system is presented based on the practical design schemes, taking the actuator and sensor integration into account.

Particle Manipulation Methods in Droplet Microfluidics.

Science.gov (United States)

Tenje, Maria; Fornell, Anna; Ohlin, Mathias; Nilsson, Johan

2018-02-06

This Feature describes the different particle manipulation techniques available in the droplet microfluidics toolbox to handle particles encapsulated inside droplets and to manipulate whole droplets. We address the advantages and disadvantages of the different techniques to guide new users.

Characterization of applied fields for ion mobility in traveling wave based structures for lossless ion manipulations (SLIM)

Energy Technology Data Exchange (ETDEWEB)

Hamid, Ahmed M.; Prabhakaran Nair Syamala Amma, Aneesh; Garimella, Venkata BS; Ibrahim, Yehia M.; Smith, Richard D.

2018-03-21

Ion mobility (IM) is rapidly gaining attention for the analysis of biomolecules due to the ability to distinguish the shapes of ions. However, conventional constant electric field drift tube IM has limited resolving power, constrained by practical limitations on the path length and maximum applied voltage. The implementation of traveling waves (TW) in IM removes the latter limitation, allowing higher resolution to be achieved using extended path lengths. These can be readily obtainable in structures for lossless ion manipulations (SLIM), which are fabricated from electric fields that are generated by appropriate potentials applied to arrays of electrodes patterned on two parallel surfaces. In this work we have investigated the relationship between the various SLIM variables, such as electrode dimensions, inter-surface gap, and the TW applied voltages, that directly impact the fields experienced by ions. Ion simulation and theoretical calculations have been utilized to understand the dependence of SLIM geometry and effective electric field. The variables explored impact both ion confinement and the observed IM resolution in Structures for Lossless Ion Manipulations (SLIM) modules.

A high-quality narrow passband filter for elastic SV waves via aligned parallel separated thin polymethylmethacrylate plates

Directory of Open Access Journals (Sweden)

Jun Zhang

2017-08-01

Full Text Available We designed a high-quality filter that consists of aligned parallel polymethylmethacrylate (PMMA thin plates with small gaps for elastic SV waves propagate in metals. Both the theoretical model and the full numerical simulation show the transmission spectrum of the elastic SV waves through such a filter has several sharp peaks with flawless transmission within the investigated frequencies. These peaks can be readily tuned by manipulating the geometry parameters of the PMMA plates. Our investigation finds that the same filter performs well for different metals where the elastic SV waves propagated.

Manipulation or Mobilisation for Neck Pain

NARCIS (Netherlands)

Gross, Anita; Miller, Jordan; D'Sylva, Jonathan; Burnie, Stephen J.; Goldsmith, Charles H.; Graham, Nadine; Haines, Ted; Brønfort, Gert; Hoving, Jan L.

2010-01-01

Background Manipulation and mobilisation are often used, either alone or combined with other treatment approaches, to treat neck pain. Objectives To assess if manipulation or mobilisation improves pain, function/disability, patient satisfaction, quality of life, and global perceived effect in adults

Modeling of Continuum Manipulators Using Pythagorean Hodograph Curves.

Science.gov (United States)

Singh, Inderjeet; Amara, Yacine; Melingui, Achille; Mani Pathak, Pushparaj; Merzouki, Rochdi

2018-05-10

Research on continuum manipulators is increasingly developing in the context of bionic robotics because of their many advantages over conventional rigid manipulators. Due to their soft structure, they have inherent flexibility, which makes it a huge challenge to control them with high performances. Before elaborating a control strategy of such robots, it is essential to reconstruct first the behavior of the robot through development of an approximate behavioral model. This can be kinematic or dynamic depending on the conditions of operation of the robot itself. Kinematically, two types of modeling methods exist to describe the robot behavior; quantitative methods describe a model-based method, and qualitative methods describe a learning-based method. In kinematic modeling of continuum manipulator, the assumption of constant curvature is often considered to simplify the model formulation. In this work, a quantitative modeling method is proposed, based on the Pythagorean hodograph (PH) curves. The aim is to obtain a three-dimensional reconstruction of the shape of the continuum manipulator with variable curvature, allowing the calculation of its inverse kinematic model (IKM). It is noticed that the performances of the PH-based kinematic modeling of continuum manipulators are considerable regarding position accuracy, shape reconstruction, and time/cost of the model calculation, than other kinematic modeling methods, for two cases: free load manipulation and variable load manipulation. This modeling method is applied to the compact bionic handling assistant (CBHA) manipulator for validation. The results are compared with other IKMs developed in case of CBHA manipulator.

Agent Control for Reconfigurable Open Kinematic Chain Manipulators

Directory of Open Access Journals (Sweden)

Janez Sluga

2013-10-01

Full Text Available This paper presents a method for the autonomous control of differently structured open kinematic chains based on multi-agent system technology. The appropriate level of distributing local autonomy (agents to a manipulative structure is defined, which makes it possible to dynamically change the number, type and structure of manipulative components without modifying their behavioural logic. To achieve fast reconfigurable and scalable manipulative systems, a new multi-agent method is developed for controlling the manipulator kinematics. The new method enables independent manipulator structure from the control system because of its structural and system modularity. The proposed method consists of kinematic equations for use in an agent environment, agent motion-planning algorithms, evaluation functions, agent control logic and kinematic algorithms. The results of simulations and real-world experiments demonstrate the usefulness of the approach for different non-redundant and redundant manipulation structures.

Sistem kontrol gerak kinematika robot gripper manipulator

Directory of Open Access Journals (Sweden)

Wayan Widhiada

2018-01-01

Full Text Available Abstrak Sistem robot manipulator ini merupakan mekanisme lengan yang terdiri dari serangkaian segmen yang digunakan untuk menangkap dan memindahkan benda dengan beberapa derajat kebebasan. Dalam perkembangannya, robot manipulator telah digunakan dalam melaksanakan misi tertentu dan membantu operasi di ruang angkasa. Robot biasanya berinteraksi dengan sistem tangan, dan dalam kegiatan industri tangan biasanya disebut sebagai gripper. Penulis menggunakan metode simulasi teknik yang dapat menentukan sistem gerak kinematika robot. Simulasi teknik adalah metode yang digunakan untuk mendesain dan menganalisa gerakan robot dimana hasil dari respon gerakan robot yang didapat mendekati hasil dalam keadaan sebenarnya. Simulasi juga dapat menghemat waktu dan biaya yang digunakan dalam mendesain robot gripper manipulator lima jari dengan elemen prismatik. Dengan menggunakan kontrol PID diharapkan respon gerak kinematik dari setiap joint robot manipulator mencapai perfomance yang terbaik seperti overshoot yang kecil, dan kondisi tenang (steady state dalam waktu yang singkat disertai dengan keselahan penggerak yang kecil. Melalui proses Advance tuning pada PID kontrol selesai didapatkan parameter penguat pada PID kontrol yaitu Kp = 0.7194, Ki = 8.306 dan Kd = 0.0061sehingga tercapai performance gerakan kinematika robot gripper manipulator yang terbaik sesuai yang dikehendaki oleh user dengan rise time yang singkat 0.52 detik, waktu puncak yang singkat 0.52 detik, maksimum overshoot yang kecil 1,8%, kesetebailan response dicapai pada 0.76 detik dan kesalahan penggerak yang sangat kecil 0.32%. Kata kunci: Robot gripper manipulator, PID control, gerakan kinematika Abstract A robot gripper manipulator system mechanism comprising a series of segments that are used to capture and move objects with multiple degrees of freedom. In the process, the robot manipulator has been used in carrying out the specific mission and assist operations in space. Robot manipulator

A Molecular Analysis of Training Multiple versus Single Manipulations to Establish a Generalized Manipulative Imitation Repertoire

Science.gov (United States)

Hartley, Breanne K.

2009-01-01

This study evaluates the necessity of training multiple versus single manipulative-imitations per object in order to establish generalized manipulative-imitation. Training took place in Croyden Avenue School's Early Childhood Developmental Delay preschool classroom in Kalamazoo, MI. Two groups of 3 children each were trained to imitate in order to…

Evaluation of Remote Collaborative Manipulation for Scientific Data Analysis

OpenAIRE

Fleury , Cédric; Duval , Thierry; Gouranton , Valérie; Steed , Anthony

2012-01-01

International audience; In the context of scientific data analysis, we propose to compare a remote collaborative manipulation technique with a single user manipulation technique. The manipulation task consists in positioning a clipping plane in order to perform cross-sections of scientific data which show several points of interest located inside this data. For the remote collaborative manipulation, we have chosen to use the 3-hand manipulation technique proposed by Aguerreche et al. which is...

Reconfigurable mobile manipulation for accident response

International Nuclear Information System (INIS)

Anderson, Robert J.; Morse, William D.; Shirey, David L.; Cdebaca, DanielL M.; Hoffman, John P. Jr.; Lucy, William E.

2000-01-01

The need for a telerobotic vehicle with hazard sensing and integral manipulation capabilities has been identified for use in transportation accidents where nuclear weapons are involved. The Accident Response Mobile Manipulation System (ARMMS) platform has been developed to provide remote dexterous manipulation and hazard sensing for the Accident Response Group (ARG) at Sandia National Laboratories. The ARMMS' mobility platform is a military HMMWV [High Mobility Multipurpose Wheeled Vehicle] that is teleoperated over RF or Fiber Optic communication channels. ARMMS is equipped with two high strength Schilling Titan II manipulators and a suite of hazardous gas and radiation sensors. Recently, a modular telerobotic control architecture call SMART (Sandia Modular Architecture for Robotic and Teleoperation) has been applied to ARMMS. SMART enables input devices and many system behaviors to be rapidly configured in the field for specific mission needs. This paper summarizes current SMART developments applied to ARMMS

Parallel algorithms for mapping pipelined and parallel computations

Science.gov (United States)

Nicol, David M.

1988-01-01

Many computational problems in image processing, signal processing, and scientific computing are naturally structured for either pipelined or parallel computation. When mapping such problems onto a parallel architecture it is often necessary to aggregate an obvious problem decomposition. Even in this context the general mapping problem is known to be computationally intractable, but recent advances have been made in identifying classes of problems and architectures for which optimal solutions can be found in polynomial time. Among these, the mapping of pipelined or parallel computations onto linear array, shared memory, and host-satellite systems figures prominently. This paper extends that work first by showing how to improve existing serial mapping algorithms. These improvements have significantly lower time and space complexities: in one case a published O(nm sup 3) time algorithm for mapping m modules onto n processors is reduced to an O(nm log m) time complexity, and its space requirements reduced from O(nm sup 2) to O(m). Run time complexity is further reduced with parallel mapping algorithms based on these improvements, which run on the architecture for which they create the mappings.

Motion control of planar parallel robot using the fuzzy descriptor system approach.

Science.gov (United States)

Vermeiren, Laurent; Dequidt, Antoine; Afroun, Mohamed; Guerra, Thierry-Marie

2012-09-01

This work presents the control of a two-degree of freedom parallel robot manipulator. A quasi-LPV approach, through the so-called TS fuzzy model and LMI constraints problems is used. Moreover, in this context a way to derive interesting control laws is to keep the descriptor form of the mechanical system. Therefore, new LMI problems have to be defined that helps to reduce the conservatism of the usual results. Some relaxations are also proposed to leave the pure quadratic stability/stabilization framework. A comparison study between the classical control strategies from robotics and the control design using TS fuzzy descriptor models is carried out to show the interest of the proposed approach. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

Phenomena of Inter-age Manipulations in Interaction "Teacher-Student"

Directory of Open Access Journals (Sweden)

Miklyaeva A.V.,

2017-01-01

Full Text Available Thearticlepresentsthe results of studies of the phenomenon empirical inter-age manipulation in the pedagogical interaction. Inter-age manipulation is considered a form of manipulation carried out on the basis of an appeal to the participants in the interaction age roles. Based on the results of a survey 109 teenagers 13-15 years, using a questionnaire, color test of relations and projective drawing shows that inter-age manipulation is a common way to impact on the students, elected teacher. Teachers are the subjects of inter-age manipulation more often than students. It was revealed that the effectiveness of inter-age manipulation in pedagogical interaction increases if it is meaningful is consistent with the normative content of age roles, as well as «inter-age distance" between the teacher and the students. The greatest effectiveness of have inter-age manipulation undertaken for older teachers, and manipulation "from below" from young teachers

Maximum allowable load on wheeled mobile manipulators

International Nuclear Information System (INIS)

Habibnejad Korayem, M.; Ghariblu, H.

2003-01-01

This paper develops a computational technique for finding the maximum allowable load of mobile manipulator during a given trajectory. The maximum allowable loads which can be achieved by a mobile manipulator during a given trajectory are limited by the number of factors; probably the dynamic properties of mobile base and mounted manipulator, their actuator limitations and additional constraints applied to resolving the redundancy are the most important factors. To resolve extra D.O.F introduced by the base mobility, additional constraint functions are proposed directly in the task space of mobile manipulator. Finally, in two numerical examples involving a two-link planar manipulator mounted on a differentially driven mobile base, application of the method to determining maximum allowable load is verified. The simulation results demonstrates the maximum allowable load on a desired trajectory has not a unique value and directly depends on the additional constraint functions which applies to resolve the motion redundancy

Laser Diode Beam Basics, Manipulations and Characterizations

CERN Document Server

Sun, Haiyin

2012-01-01

Many optical design technical books are available for many years which mainly deal with image optics design based on geometric optics and using sequential raytracing technique. Some books slightly touched laser beam manipulation optics design. On the other hand many books on laser diodes have been published that extensively deal with laser diode physics with little touching on laser diode beam manipulations and characterizations. There are some internet resources dealing with laser diode beams. However, these internet resources have not covered enough materials with enough details on laser diode beam manipulations and characterizations. A technical book concentrated on laser diode beam manipulations and characterizations can fit in to the open and provide useful information to laser diode users. Laser Diode Beam Basics, Manipulations and  Characterizations is concentrated on the very practical side of the subject, it only discusses the basic physics and mathematics that are necessary for the readers in order...

Manipulatives Work!

Science.gov (United States)

Moch, Peggy L.

2001-01-01

Fifth graders (n=16) engaged in manipulative activities to improve their grasp of math concepts; one-third were identified as exceptional children. Posttest results after 12 lessons showed the overall class average increased from 49% to 59% and all areas improved compared to pretest scores. Attitude changes were also apparent. (Contains 24…

SAMSIN: the next-generation servo-manipulator

International Nuclear Information System (INIS)

Adams, R.H.; Jennrich, C.E.; Korpi, K.W.

1985-01-01

The Central Research Laboratories (CRL) Division of Sargent Industries is now developing SAMSIN, a next-generation servo-manipulator. SAMSIN is an acronym for Servo-Actuated Manipulator Systems with Intelligent Networks. This paper discusses the objectives of this development and describes the key features of the servo-manipulator system. There are three main objectives in the SAMSIN development: adaptability, reliability, and maintainability. SAMSIN utilizes standard Sargent/CRL sealed master and slave manipulator arms as well as newly developed compact versions. The mechanical arms have more than 20 yr of successful performance in industrial applications such as hot cells, high vacuums, fuel pools, and explosives handling. The servo-actuator package is in a protective enclosure, which may be sealed in various ways from the remote environment. The force limiting characteristics of the servo-actuators extend motion tendon life. Protective bootings increase the reliability of the arms in an environment that is high in airborne contamination. These bootings also simplify the decontamination of the system. The modularity in construction permits quick removal and replacement of slave arms, wrist joints, tong fingers, and actuator packages for maintenance. SAMSIN utilizes readily available off-the-shelf actuator and control system components. Each manipulator motion uses the same actuator and control system components

Seismic qualification of existing safety class manipulators

International Nuclear Information System (INIS)

Wu, Ting-shu; Moran, T.J.

1992-01-01

There are two bridge type electromechanical manipulators within a nuclear fuel handling facility which were constructed over twenty-five years ago. At that time, there were only minimal seismic considerations. These manipulators together with the facility are being reactivated. Detailed analyses have shown that the manipulators will satisfy the requirements of ANSI/AISC N690-1984 when they are subjected to loadings including the site specific design basis earthquake. 4 refs

Control of master-slave manipulator using virtual force

International Nuclear Information System (INIS)

Kosuge, Kazuhiro; Fukuda, Toshio; Itoh, Tomotaka; Sakamoto, Keizoh; Noma, Yasuo.

1994-01-01

We propose a control system for a master-slave manipulator system having a rate-controlled slave manipulator. In this system, the master manipulator is stiffness-controlled in the Cartesian coordinate system, and the slave manipulator is damping-controlled in the Cartesian coordinate system. The desired velocity of the slave arm is given by a displacement of the master arm from a nominal position. The operator feels virtual contact force from the environment because the contact force is proportional to the displacement when the slave arm motion is constrained by the environment. The proposed method is experimentally applied to manipulators with three degrees of freedom. The experimental results illustrate the validity of the proposed system. (author)

Parallel computing works

Energy Technology Data Exchange (ETDEWEB)

1991-10-23

An account of the Caltech Concurrent Computation Program (C{sup 3}P), a five year project that focused on answering the question: Can parallel computers be used to do large-scale scientific computations '' As the title indicates, the question is answered in the affirmative, by implementing numerous scientific applications on real parallel computers and doing computations that produced new scientific results. In the process of doing so, C{sup 3}P helped design and build several new computers, designed and implemented basic system software, developed algorithms for frequently used mathematical computations on massively parallel machines, devised performance models and measured the performance of many computers, and created a high performance computing facility based exclusively on parallel computers. While the initial focus of C{sup 3}P was the hypercube architecture developed by C. Seitz, many of the methods developed and lessons learned have been applied successfully on other massively parallel architectures.

How to Make the Most of Math Manipulatives.

Science.gov (United States)

Burns, Marilyn

1996-01-01

A discussion of how to use math manipulatives to teach elementary students focuses on essential program elements: what math manipulatives are and why they are used, common questions about math manipulatives, how one teacher introduced the geoboard into the classroom, and pattern block activities. (SM)

Computational simulator of robotic manipulators

International Nuclear Information System (INIS)

Leal, Alexandre S.; Campos, Tarcisio P.R.

1995-01-01

Robotic application for industrial plants is discussed and a computational model for a mechanical manipulator of three links is presented. A neural network feed-forward type has been used to model the dynamic control of the manipulator. A graphic interface was developed in C programming language as a virtual world in order to visualize and simulate the arm movements handling radioactive waste environment. (author). 7 refs, 5 figs

Advanced manipulator system for large hot cells

International Nuclear Information System (INIS)

Vertut, J.; Moreau, C.; Brossard, J.P.

1981-01-01

Large hot cells can be approached as extrapolated from smaller ones as wide, higher or longer in size with the same concept of using mechanical master slave manipulators and high density windows. This concept leads to a large number of working places and corresponding equipments, with a number of penetrations through the biological protection. When the large cell does not need a permanent operation of number of work places, as in particular to serve PIE machines and maintain the facility, use of servo manipulators with a large supporting unit and extensive use of television appears optimal. The advance on MA 23 and supports will be described including the extra facilities related to manipulators introduction and maintenance. The possibility to combine a powered manipulator and MA 23 (single or pair) on the same boom crane system will be described. An advance control system to bring the minimal dead time to control support movement, associated to the master slave arm operation is under development. The general television system includes over view cameras, associated with the limited number of windows, and manipulators camera. A special new system will be described which brings an automatic control of manipulator cameras and saves operator load and dead time. Full scale tests with MA 23 and support will be discussed. (author)

Digital Manipulation in Scientific Images: Some Ethical Considerations.

Science.gov (United States)

Hayden, James E.

2000-01-01

Discusses the importance of images in the publishing and presentation of scientific research. Explains the use of photographs as scientific data in research. Lists some reasons for the manipulation of images, and clarifies the acceptable and unacceptable limits of manipulation and image manipulation policy. (Author/YDS)

Manipulating stored phonological input during verbal working memory

Science.gov (United States)

Cogan, Gregory B.; Iyer, Asha; Melloni, Lucia; Thesen, Thomas; Friedman, Daniel; Doyle, Werner; Devinsky, Orrin; Pesaran, Bijan

2016-01-01

Verbal working memory (vWM), involves storing and manipulating information in phonological sensory input. An influential theory of vWM proposes that manipulation is carried out by a central executive while storage is performed by two interacting systems: A phonological input buffer that captures sound-based information and an articulatory rehearsal system that controls speech motor output. Whether, when, and how neural activity in the brain encodes these components remains unknown. Here, we read-out the contents of vWM from neural activity in human subjects as they manipulate stored speech sounds. As predicted, we identify storage systems that contain both phonological sensory and articulatory motor representations. Surprisingly however, we find that manipulation does not involve a single central executive but rather involves two systems with distinct contributions to successful manipulation. We propose, therefore, that multiple subsystems comprise the central executive needed to manipulate stored phonological input for articulatory motor output in vWM. PMID:27941789

MODULAR MANIPULATOR FOR ROBOTICS APPLICATIONS

International Nuclear Information System (INIS)

Geisinger, Joseph W. Ph.D.

2001-01-01

ARM Automation, Inc. is developing a FR-amework of modular actuators that can address the DOE's wide range of robotics needs. The objective of this effort is to demonstrate the effectiveness of this technology by constructing a manipulator FR-om these actuators within a glovebox for Automated Plutonium Processing (APP). At the end of the project, the system of actuators was used to construct several different manipulator configurations, which accommodate common glovebox tasks such as repackaging. The modular nature and quickconnects of this system simplify installation into ''hot'' boxes and any potential modifications or repair therein. This work focused on the development of self-contained robotic actuator modules including the embedded electronic controls for the purpose of building a manipulator system. Both of the actuators developed under this project contain the control electronics, sensors, motor, gear train, wiring, system communications and mechanical interfaces of a complete robotics servo device. Test actuators and accompanying DISC(trademark)s underwent validation testing at The University of Texas at Austin and ARM Automation, Inc. following final design and fabrication. The system also included custom links, an umbilical cord, an open architecture PC-based system controller, and operational software that permitted integration into a completely functional robotic manipulator system. The open architecture on which this system is based avoids proprietary interfaces and communication protocols which only serve to limit the capabilities and flexibility of automation equipment. The system was integrated and tested in the contractor's facility for intended performance and operations. The manipulator was tested using the full-scale equipment and process mock-ups. The project produced a practical and operational system including a quantitative evaluation of its performance and cost

Manipulation of biological samples using micro and nano techniques.

Science.gov (United States)

Castillo, Jaime; Dimaki, Maria; Svendsen, Winnie Edith

2009-01-01

The constant interest in handling, integrating and understanding biological systems of interest for the biomedical field, the pharmaceutical industry and the biomaterial researchers demand the use of techniques that allow the manipulation of biological samples causing minimal or no damage to their natural structure. Thanks to the advances in micro- and nanofabrication during the last decades several manipulation techniques offer us the possibility to image, characterize and manipulate biological material in a controlled way. Using these techniques the integration of biomaterials with remarkable properties with physical transducers has been possible, giving rise to new and highly sensitive biosensing devices. This article reviews the different techniques available to manipulate and integrate biological materials in a controlled manner either by sliding them along a surface (2-D manipulation), by grapping them and moving them to a new position (3-D manipulation), or by manipulating and relocating them applying external forces. The advantages and drawbacks are mentioned together with examples that reflect the state of the art of manipulation techniques for biological samples (171 references).

Improvement of the M/S manipulator maintenance at OSL

International Nuclear Information System (INIS)

Kuwana, Koichi; Ouchi, Hiroshi; Ito, Yutaka; Sato, Yoshihiro; Midorikawa, Mituhiro; Hayakawa, Tuyoshi

2010-01-01

The safeguards inspection samples from the JNFL Rokkasho Reprocessing Plant (RRP) are received and analyzed at the On Site Laboratory (OSL). Since the samples from the input accountancy tank of the RRP contain a lot of fission products, they are treated in a hot-cell line with a M/S (Master /Slave) manipulator. Special equipment and tools were used for the maintenance of the M/S manipulator, especially for the exchange of the M/S manipulator. However, the manipulator exchange work was not easy due to the limitation of the space in the OSL. For solution to this problem, a monorail and monorail hoist equipment was installed onto wall surface of analytical room close to each M/S manipulator, and then it made the exchange of M/S manipulator easy without special equipment and tools. Additionally, operator was freed from the burden of working space arranging for the exchange of M/S manipulator such as removing of analytical equipments. This report represents the improvement of operation for the exchange of M/S manipulator with installation of monorail and hoist equipment. (author)

Template based parallel checkpointing in a massively parallel computer system

Science.gov (United States)

Archer, Charles Jens [Rochester, MN; Inglett, Todd Alan [Rochester, MN

2009-01-13

A method and apparatus for a template based parallel checkpoint save for a massively parallel super computer system using a parallel variation of the rsync protocol, and network broadcast. In preferred embodiments, the checkpoint data for each node is compared to a template checkpoint file that resides in the storage and that was previously produced. Embodiments herein greatly decrease the amount of data that must be transmitted and stored for faster checkpointing and increased efficiency of the computer system. Embodiments are directed to a parallel computer system with nodes arranged in a cluster with a high speed interconnect that can perform broadcast communication. The checkpoint contains a set of actual small data blocks with their corresponding checksums from all nodes in the system. The data blocks may be compressed using conventional non-lossy data compression algorithms to further reduce the overall checkpoint size.

Manipulations of Totalitarian Nazi Architecture

Science.gov (United States)

Antoszczyszyn, Marek

2017-10-01

The paper takes under considerations controversies surrounding German architecture designed during Nazi period between 1933-45. This architecture is commonly criticized for being out of innovation, taste & elementary sense of beauty. Moreover, it has been consequently wiped out from architectural manuals, probably for its undoubted associations with the totalitarian system considered as the most maleficent in the whole history. But in the meantime the architecture of another totalitarian system which appeared to be not less sinister than Nazi one is not stigmatized with such verve. It is Socrealism architecture, developed especially in East Europe & reportedly containing lots of similarities with Nazi architecture. Socrealism totalitarian architecture was never condemned like Nazi one, probably due to politically manipulated propaganda that influenced postwar public opinion. This observation leads to reflection that maybe in the same propaganda way some values of Nazi architecture are still consciously dissembled in order to hide the fact that some rules used by Nazi German architects have been also consciously used after the war. Those are especially manipulations that allegedly Nazi architecture consisted of. The paper provides some definitions around totalitarian manipulations as well as ideological assumptions for their implementation. Finally, the register of confirmed manipulations is provided with use of photo case study.

Lazy motion planning for robotic manipulators

NARCIS (Netherlands)

Andrien, A.R.P.; van de Molengraft, M.J.G.; Bruyninckx, H.P.J.

2017-01-01

Robotic manipulators are making a shift towards mobile bases in both industry and domestic environments, which puts high demands on efficient use of the robot’s limited energy resources. In this work, the problem of reducing energy usage of a robot manipulator during a task is investigated. We

Manipulators inspired by the tongue of the chameleon.

Science.gov (United States)

Debray, Alexis

2011-06-01

Chameleons have developed a specialized ballistic tongue which elongates more than six times its rest length at speeds higher than 3.5 m s(-1) and accelerations 350 m s(-2), with a highly flexible mobile part, and which applies no continuous force during forward motion. These characteristics are possible because this tongue consists of two highly specialized systems, an ejection system for the forward motion and an accordion-like system for the retraction. Four manipulators inspired by the tongue of the chameleon and based on this design have been developed, resulting in three characteristics similar to the tongue of the chameleon: extensibility of the manipulator, flexibility of the mobile part, and absence of continuous force during the forward motion. The first manipulator mimics the basic mechanism of the tongue of the chameleon and reproduced its basic performances. A second manipulator performs a catching function at a speed of 3.5 m s(-1) with an acceleration of 573 m s(-2) while elongating seven times its rest length. The design of this manipulator is such that the dc motor used for retraction applies a torque 25 times its rated torque. Moreover, during the retraction, the mobile part of the manipulator moves due to its own inertia, allowing the dc motor to rotate at full velocity. In another manipulator, the addition of an elastomer in the mobile part allows for control of the retraction velocity. A model for these two manipulators compares well with the experimental data. Finally, the addition of wings on the mobile part allows us to take the advantage of aerodynamic effects, which is unusual for manipulators.

Manipulators inspired by the tongue of the chameleon

International Nuclear Information System (INIS)

Debray, Alexis

2011-01-01

Chameleons have developed a specialized ballistic tongue which elongates more than six times its rest length at speeds higher than 3.5 m s -1 and accelerations 350 m s -2 , with a highly flexible mobile part, and which applies no continuous force during forward motion. These characteristics are possible because this tongue consists of two highly specialized systems, an ejection system for the forward motion and an accordion-like system for the retraction. Four manipulators inspired by the tongue of the chameleon and based on this design have been developed, resulting in three characteristics similar to the tongue of the chameleon: extensibility of the manipulator, flexibility of the mobile part, and absence of continuous force during the forward motion. The first manipulator mimics the basic mechanism of the tongue of the chameleon and reproduced its basic performances. A second manipulator performs a catching function at a speed of 3.5 m s -1 with an acceleration of 573 m s -2 while elongating seven times its rest length. The design of this manipulator is such that the dc motor used for retraction applies a torque 25 times its rated torque. Moreover, during the retraction, the mobile part of the manipulator moves due to its own inertia, allowing the dc motor to rotate at full velocity. In another manipulator, the addition of an elastomer in the mobile part allows for control of the retraction velocity. A model for these two manipulators compares well with the experimental data. Finally, the addition of wings on the mobile part allows us to take the advantage of aerodynamic effects, which is unusual for manipulators.

Manipulators inspired by the tongue of the chameleon

Energy Technology Data Exchange (ETDEWEB)

Debray, Alexis, E-mail: debray.alexis@canon.co.jp [Canon Incorporation, 3-30-2, Shimomaruko, Ohta-ku, Tokyo 146-8501 (Japan)

2011-06-15

Chameleons have developed a specialized ballistic tongue which elongates more than six times its rest length at speeds higher than 3.5 m s{sup -1} and accelerations 350 m s{sup -2}, with a highly flexible mobile part, and which applies no continuous force during forward motion. These characteristics are possible because this tongue consists of two highly specialized systems, an ejection system for the forward motion and an accordion-like system for the retraction. Four manipulators inspired by the tongue of the chameleon and based on this design have been developed, resulting in three characteristics similar to the tongue of the chameleon: extensibility of the manipulator, flexibility of the mobile part, and absence of continuous force during the forward motion. The first manipulator mimics the basic mechanism of the tongue of the chameleon and reproduced its basic performances. A second manipulator performs a catching function at a speed of 3.5 m s{sup -1} with an acceleration of 573 m s{sup -2} while elongating seven times its rest length. The design of this manipulator is such that the dc motor used for retraction applies a torque 25 times its rated torque. Moreover, during the retraction, the mobile part of the manipulator moves due to its own inertia, allowing the dc motor to rotate at full velocity. In another manipulator, the addition of an elastomer in the mobile part allows for control of the retraction velocity. A model for these two manipulators compares well with the experimental data. Finally, the addition of wings on the mobile part allows us to take the advantage of aerodynamic effects, which is unusual for manipulators.

Can earnings manipulation create value?

OpenAIRE

Anton Miglo

2008-01-01

Existing literature usually considers earnings manipulation to be a negative social phenomenon. We argue that earnings manipulation can be a part of the equilibrium relationships between firm's insiders and outsiders. We consider an optimal contract between an entrepreneur and an investor where the entrepreneur is subject to a double moral hazard problem (one being the choice of production effort and the other being intertemporal substitution, which consists of transferring cash flows between...

A Geometry Deformation Model for Braided Continuum Manipulators

Directory of Open Access Journals (Sweden)

S. M. Hadi Sadati

2017-06-01

Full Text Available Continuum manipulators have gained significant attention in the robotic community due to their high dexterity, deformability, and reachability. Modeling of such manipulators has been shown to be very complex and challenging. Despite many research attempts, a general and comprehensive modeling method is yet to be established. In this paper, for the first time, we introduce the bending effect in the model of a braided extensile pneumatic actuator with both stiff and bendable threads. Then, the effect of the manipulator cross-section deformation on the constant curvature and variable curvature models is investigated using simple analytical results from a novel geometry deformation method and is compared to experimental results. We achieve 38% mean reference error simulation accuracy using our constant curvature model for a braided continuum manipulator in presence of body load and 10% using our variable curvature model in presence of extensive external loads. With proper model assumptions and taking to account the cross-section deformation, a 7–13% increase in the simulation mean error accuracy is achieved compared to a fixed cross-section model. The presented models can be used for the exact modeling and design optimization of compound continuum manipulators by providing an analytical tool for the sensitivity analysis of the manipulator performance. Our main aim is the application in minimal invasive manipulation with limited workspaces and manipulators with regional tunable stiffness in their cross section.

The application of manipulator robot for nuclear plant maintenance

International Nuclear Information System (INIS)

Kohata, Yukifumi; Fujita, Jun; Onishi, Ken; Tsuhari, Hiroyuki; Hosoe, Fumihiro

2010-01-01

In the maintenance works at nuclear power plant, robots are used because of high radiation, narrow space and underwater work. Various robots are needed because there is various maintenance works. This is inefficiency. As the solutions, we developed manipulator robots for the access of specialized tools. This study shows manipulator robots developed by MHI, application example to maintenance works and effectiveness of manipulator robots. When robotization of maintenance works are considered, manipulator technology is very effective solution means. We achieved efficiency improvement and the reliability improvement by developing a high generality manipulator. (author)

Physics Based Vision Systems for Robotic Manipulation

Data.gov (United States)

National Aeronautics and Space Administration — With the increase of robotic manipulation tasks (TA4.3), specifically dexterous manipulation tasks (TA4.3.2), more advanced computer vision algorithms will be...

Introduction to parallel programming

CERN Document Server

Brawer, Steven

1989-01-01

Introduction to Parallel Programming focuses on the techniques, processes, methodologies, and approaches involved in parallel programming. The book first offers information on Fortran, hardware and operating system models, and processes, shared memory, and simple parallel programs. Discussions focus on processes and processors, joining processes, shared memory, time-sharing with multiple processors, hardware, loops, passing arguments in function/subroutine calls, program structure, and arithmetic expressions. The text then elaborates on basic parallel programming techniques, barriers and race

Distinguishing manipulated stocks via trading network analysis

Science.gov (United States)

Sun, Xiao-Qian; Cheng, Xue-Qi; Shen, Hua-Wei; Wang, Zhao-Yang

2011-10-01

Manipulation is an important issue for both developed and emerging stock markets. For the study of manipulation, it is critical to analyze investor behavior in the stock market. In this paper, an analysis of the full transaction records of over a hundred stocks in a one-year period is conducted. For each stock, a trading network is constructed to characterize the relations among its investors. In trading networks, nodes represent investors and a directed link connects a stock seller to a buyer with the total trade size as the weight of the link, and the node strength is the sum of all edge weights of a node. For all these trading networks, we find that the node degree and node strength both have tails following a power-law distribution. Compared with non-manipulated stocks, manipulated stocks have a high lower bound of the power-law tail, a high average degree of the trading network and a low correlation between the price return and the seller-buyer ratio. These findings may help us to detect manipulated stocks.

System Integration for Real-Time Mobile Manipulation

Directory of Open Access Journals (Sweden)

Reza Oftadeh

2014-03-01

Full Text Available Mobile manipulators are one of the most complicated types of mechatronics systems. The performance of these robots in performing complex manipulation tasks is highly correlated with the synchronization and integration of their low-level components. This paper discusses in detail the mechatronics design of a four wheel steered mobile manipulator. It presents the manipulator's mechanical structure and electrical interfaces, designs low-level software architecture based on embedded PC-based controls, and proposes a systematic solution based on code generation products of MATLAB and Simulink. The remote development environment described here is used to develop real-time controller software and modules for the mobile manipulator under a POSIX-compliant, real-time Linux operating system. Our approach enables developers to reliably design controller modules that meet the hard real-time constraints of the entire low-level system architecture. Moreover, it provides a systematic framework for the development and integration of hardware devices with various communication mediums and protocols, which facilitates the development and integration process of the software controller.

Development of a maintenance manipulator for TFTR

International Nuclear Information System (INIS)

Holloway, C.

1986-01-01

The maintenance manipulator is a device permanently connected to the Tokamak Fusion Test Reactor (TFTR) vacuum vessel and is located in close proximity to the tokamak. It is used for the inspection and maintenance of in-vessel components whilst the machine remains under vacuum. The total system comprises a vacuum vessel ante-chamber that houses the manipulator, an articulated boom and carriage that transports and positions a dexterous end-effector, and end-effector that supports maintenance tooling, and an inspection system. Because of the maintenance manipulator's operating environment, there are many challenging engineering features, i.e., temperatures up to 150 0 C, changing magnetic fields in space and time that act on the manipulator whilst it is at rest, neutron neutron fluxes of up to 10/sup 11/cm/sup -2/s/sup -1/, and, last but not least, UHV conditions. This paper describes the development of the vacuum system, the maintenance manipulator, and inspective devices. It includes the methods employed to overcome the engineering difficulties and the application of information gained from other advanced technology programs, such as space and nuclear fission

Parallelism in matrix computations

CERN Document Server

Gallopoulos, Efstratios; Sameh, Ahmed H

2016-01-01

This book is primarily intended as a research monograph that could also be used in graduate courses for the design of parallel algorithms in matrix computations. It assumes general but not extensive knowledge of numerical linear algebra, parallel architectures, and parallel programming paradigms. The book consists of four parts: (I) Basics; (II) Dense and Special Matrix Computations; (III) Sparse Matrix Computations; and (IV) Matrix functions and characteristics. Part I deals with parallel programming paradigms and fundamental kernels, including reordering schemes for sparse matrices. Part II is devoted to dense matrix computations such as parallel algorithms for solving linear systems, linear least squares, the symmetric algebraic eigenvalue problem, and the singular-value decomposition. It also deals with the development of parallel algorithms for special linear systems such as banded ,Vandermonde ,Toeplitz ,and block Toeplitz systems. Part III addresses sparse matrix computations: (a) the development of pa...

Path planning of master-slave manipulator using graphic simulator

International Nuclear Information System (INIS)

Lee, J. Y.; Kim, S. H.; Song, T. K.; Park, B. S.; Yoon, J. S.

2002-01-01

To handle the high level radioactive materials such as spent fuels remotely, the master-slave manipulator is generally used as a remote handling equipment in the hot cell. To analyze the motion and to implement the training system by virtual reality technology, the simulator for M-S manipulator using the computer graphics is developed. The parts are modelled in 3-D graphics, assembled, and kinematics are assigned. The inverse kinematics of the manipulator is defined, and the slave of manipulator is coupled with master by the manipulator's specification. Also, the virtual work cell is implemented in the graphical environment which is the same as the real environment and the path planning method using the function of the collision detection for a manipulator are proposed. This graphic simulator of manipulator can be effectively used in designing of the maintenance processes for the hot cell equipment and enhance the reliability of the spent fuel management

Pose Space Surface Manipulation

Directory of Open Access Journals (Sweden)

Yusuke Yoshiyasu

2012-01-01

Full Text Available Example-based mesh deformation techniques produce natural and realistic shapes by learning the space of deformations from examples. However, skeleton-based methods cannot manipulate a global mesh structure naturally, whereas the mesh-based approaches based on a translational control do not allow the user to edit a local mesh structure intuitively. This paper presents an example-driven mesh editing framework that achieves both global and local pose manipulations. The proposed system is built with a surface deformation method based on a two-step linear optimization technique and achieves direct manipulations of a model surface using translational and rotational controls. With the translational control, the user can create a model in natural poses easily. The rotational control can adjust the local pose intuitively by bending and twisting. We encode example deformations with a rotation-invariant mesh representation which handles large rotations in examples. To incorporate example deformations, we infer a pose from the handle translations/rotations and perform pose space interpolation, thereby avoiding involved nonlinear optimization. With the two-step linear approach combined with the proposed multiresolution deformation method, we can edit models at interactive rates without losing important deformation effects such as muscle bulging.

Development of an optimum end-effector with a nano-scale uneven surface for non-adhesion cell manipulation using a micro-manipulator

International Nuclear Information System (INIS)

Horade, M; Kojima, M; Kamiyama, K; Kurata, T; Mae, Y; Arai, T

2015-01-01

In order to realize effective micro-manipulation using a micro-manipulator system, an optimum end-effector is proposed. Cell-manipulation experiments using mouse fibroblast cells are conducted, and the usability of the proposed end-effector is confirmed. A key advantage of the micro-manipulator is high-accuracy, high-speed 3D micro- and nano-scale positioning. Micro-manipulation has often been used in research involving biological cells. However, there are two important concerns with the micro-manipulator system: gripping efficiency and the release of gripped objects. When it is not possible to grip a micro-object, such as a cell, near its center, the object may be dropped during manipulation. Since the acquisition of exact position information for a micro-object in the vertical direction is difficult using a microscope, the gripping efficiency of the end-effector should be improved. Therefore, technical skill or operational support is required. Since, on the micro-scale, surface forces such as the adsorption force are greater than body forces, such as the gravitational force, the adhesion force between the end-effector and the object is strong. Therefore, manipulation techniques without adhesion are required for placed an object at an arbitrary position. In the present study, we consider direct physical contact between the end-effector and objects. First, the design and materials of the end-effector for micro-scale manipulation were optimized, and an end-effector with an optimum shape to increase the grip force was fabricated. Second, the surface of the end-effector tip was made uneven, and the adhesion force from increasing on the micro-scale was prevented. When an end-effector with an uneven surface was used, release without adhesion was successful 85.0% of the time. On the other hand, when an end-effector without an uneven surface was used, release without adhesion was successful 6.25% of the time. Therefore, the superiority of a structure with an uneven

MODULAR MANIPULATOR FOR ROBOTICS APPLICATIONS

Energy Technology Data Exchange (ETDEWEB)

Joseph W. Geisinger, Ph.D.

2001-07-31

ARM Automation, Inc. is developing a framework of modular actuators that can address the DOE's wide range of robotics needs. The objective of this effort is to demonstrate the effectiveness of this technology by constructing a manipulator from these actuators within a glovebox for Automated Plutonium Processing (APP). At the end of the project, the system of actuators was used to construct several different manipulator configurations, which accommodate common glovebox tasks such as repackaging. The modular nature and quickconnects of this system simplify installation into ''hot'' boxes and any potential modifications or repair therein. This work focused on the development of self-contained robotic actuator modules including the embedded electronic controls for the purpose of building a manipulator system. Both of the actuators developed under this project contain the control electronics, sensors, motor, gear train, wiring, system communications and mechanical interfaces of a complete robotics servo device. Test actuators and accompanying DISC{trademark}s underwent validation testing at The University of Texas at Austin and ARM Automation, Inc. following final design and fabrication. The system also included custom links, an umbilical cord, an open architecture PC-based system controller, and operational software that permitted integration into a completely functional robotic manipulator system. The open architecture on which this system is based avoids proprietary interfaces and communication protocols which only serve to limit the capabilities and flexibility of automation equipment. The system was integrated and tested in the contractor's facility for intended performance and operations. The manipulator was tested using the full-scale equipment and process mock-ups. The project produced a practical and operational system including a quantitative evaluation of its performance and cost.

Model-driven product line engineering for mapping parallel algorithms to parallel computing platforms

NARCIS (Netherlands)

Arkin, Ethem; Tekinerdogan, Bedir

2016-01-01

Mapping parallel algorithms to parallel computing platforms requires several activities such as the analysis of the parallel algorithm, the definition of the logical configuration of the platform, the mapping of the algorithm to the logical configuration platform and the implementation of the

Judging Nudging : Answering the Manipulation Objection

NARCIS (Netherlands)

Nys, Thomas; Engelen, Bart

2017-01-01

Is it ever justified to ‘nudge’ people towards their own health? In this article, we argue that it is. We do so by arguing (1) that nudges are not necessarily – as is commonly thought – manipulative; (2) that even those nudges that are manipulative can be justified, for instance, when they preserve

Surgical manipulation of mammalian embryos in vitro.

Science.gov (United States)

Naruse, I; Keino, H; Taniguchi, M

1997-04-01

Whole-embryo culture systems are useful in the fields of not only embryology but also teratology, toxicology, pharmacology, and physiology. Of the many advantages of whole-embryo culture, we focus here on the surgical manipulation of mammalian embryos. Whole-embryo culture allows us to manipulate mammalian embryos, similarly to fish, amphibian and avian embryos. Many surgical experiments have been performed in mammalian embryos in vitro. Such surgical manipulation alters the destiny of morphogenesis of the embryos and can answer many questions concerning developmental issues. As an example of surgical manipulation using whole-embryo culture systems, one of our experiments is described. Microsurgical electrocauterization of the deep preaxial mesodermal programmed cell death zone (fpp) in the footplate prevented the manifestation of polydactyly in genetic polydactyly mouse embryos (Pdn/Pdn), in which fpp was abolished.

Parallelization in Modern C++

CERN Multimedia

CERN. Geneva

2016-01-01

The traditionally used and well established parallel programming models OpenMP and MPI are both targeting lower level parallelism and are meant to be as language agnostic as possible. For a long time, those models were the only widely available portable options for developing parallel C++ applications beyond using plain threads. This has strongly limited the optimization capabilities of compilers, has inhibited extensibility and genericity, and has restricted the use of those models together with other, modern higher level abstractions introduced by the C++11 and C++14 standards. The recent revival of interest in the industry and wider community for the C++ language has also spurred a remarkable amount of standardization proposals and technical specifications being developed. Those efforts however have so far failed to build a vision on how to seamlessly integrate various types of parallelism, such as iterative parallel execution, task-based parallelism, asynchronous many-task execution flows, continuation s...

Automatic camera tracking for remote manipulators

International Nuclear Information System (INIS)

Stoughton, R.S.; Martin, H.L.; Bentz, R.R.

1984-07-01

The problem of automatic camera tracking of mobile objects is addressed with specific reference to remote manipulators and using either fixed or mobile cameras. The technique uses a kinematic approach employing 4 x 4 coordinate transformation matrices to solve for the needed camera PAN and TILT angles. No vision feedback systems are used, as the required input data are obtained entirely from position sensors from the manipulator and the camera-positioning system. All hardware requirements are generally satisfied by currently available remote manipulator systems with a supervisory computer. The system discussed here implements linear plus on/off (bang-bang) closed-loop control with a +-2-deg deadband. The deadband area is desirable to avoid operator seasickness caused by continuous camera movement. Programming considerations for camera control, including operator interface options, are discussed. The example problem presented is based on an actual implementation using a PDP 11/34 computer, a TeleOperator Systems SM-229 manipulator, and an Oak Ridge National Laboratory (ORNL) camera-positioning system. 3 references, 6 figures, 2 tables

Automatic camera tracking for remote manipulators

International Nuclear Information System (INIS)

Stoughton, R.S.; Martin, H.L.; Bentz, R.R.

1984-04-01

The problem of automatic camera tracking of mobile objects is addressed with specific reference to remote manipulators and using either fixed or mobile cameras. The technique uses a kinematic approach employing 4 x 4 coordinate transformation matrices to solve for the needed camera PAN and TILT angles. No vision feedback systems are used, as the required input data are obtained entirely from position sensors from the manipulator and the camera-positioning system. All hardware requirements are generally satisfied by currently available remote manipulator systems with a supervisory computer. The system discussed here implements linear plus on/off (bang-bang) closed-loop control with a +-2 0 deadband. The deadband area is desirable to avoid operator seasickness caused by continuous camera movement. Programming considerations for camera control, including operator interface options, are discussed. The example problem presented is based on an actual implementation using a PDP 11/34 computer, a TeleOperator Systems SM-229 manipulator, and an Oak Ridge National Laboratory (ORNL) camera-positioning system. 3 references, 6 figures, 2 tables

Open and closed loop manipulation of charged microchiplets in an electric field

Energy Technology Data Exchange (ETDEWEB)

Lu, J. P., E-mail: jplu@parc.com; Thompson, J. D.; Whiting, G. L.; Biegelsen, D. K.; Raychaudhuri, S.; Lujan, R.; Veres, J.; Lavery, L. L.; Völkel, A. R.; Chow, E. M. [Palo Alto Research Center, Inc., 3333 Coyote Hill Rd., Palo Alto, California 94304 (United States)

2014-08-04

We demonstrate the ability to orient, position, and transport microchips (“chiplets”) with electric fields. In an open-loop approach, modified four phase traveling wave potential patterns manipulate chiplets in a dielectric solution using dynamic template agitation techniques. Repeatable parallel assembly of chiplets is demonstrated to a positional accuracy of 6.5 μm using electrodes of 200 μm pitch. Chiplets with dipole surface charge patterns are used to show that orientation can be controlled by adding unique charge patterns on the chiplets. Chip path routing is also demonstrated. With a closed-loop control system approach using video feedback, dielectric, and electrophoretic forces are used to achieve positioning accuracy of better than 1 μm with 1 mm pitch driving electrodes. These chip assembly techniques have the potential to enable future printer systems where inputs are electronic chiplets and the output is a functional electronic system.

A systematic review of the use of dosage form manipulation to obtain required doses to inform use of manipulation in paediatric practice.

Science.gov (United States)

Richey, Roberta H; Hughes, Clare; Craig, Jean V; Shah, Utpal U; Ford, James L; Barker, Catrin E; Peak, Matthew; Nunn, Anthony J; Turner, Mark A

2017-02-25

This study sought to determine whether there is an evidence base for drug manipulation to obtain the required dose, a common feature of paediatric clinical practice. A systematic review of the data sources, PubMed, EMBASE, CINAHL, IPA and the Cochrane database of systematic reviews, was used. Studies that considered the dose accuracy of manipulated medicines of any dosage form, evidence of safety or harm, bioavailability, patient experience, tolerability, contamination and comparison of methods of manipulation were included. Case studies and letters were excluded. Fifty studies were eligible for inclusion, 49 of which involved tablets being cut, split, crushed or dispersed. The remaining one study involved the manipulation of suppositories of one drug. No eligible studies concerning manipulation of oral capsules or liquids, rectal enemas, nebuliser solutions, injections or transdermal patches were identified. Twenty four of the tablet studies considered dose accuracy using weight and/or drug content. In studies that considered weight using adapted pharmacopoeial specifications, the percentage of halved tablets meeting these specifications ranged from 30% to 100%. Eighteen studies investigated bioavailability, pharmacokinetics or clinical outcomes following manipulations which included nine delayed or modified release formulations. In each of these nine studies the entirety of the dosage form was administered. Only one of the 18 studies was identified where drugs were manipulated to obtain a proportion of the dosage form, and that proportion administered. The five studies that considered patient perception found that having to manipulate the tablets did not have a negative impact on adherence. Of the 49 studies only two studies reported investigating children. This review yielded limited evidence to support manipulation of medicines for children. The results cannot be extrapolated between dosage forms, methods of manipulation or between different brands of the same

Manipulators in deep ocean environments, needs versus technology

International Nuclear Information System (INIS)

Mackey, L.A.; Stenovec, G.M.

1984-01-01

As exploration and production proceed into deeper water, remotely operated vehicles (ROVs) and their manipulators acquire many of the tasks now performed by divers in shallower water. The resulting increased complexity of work tasks requires more dexterious manipulators. Even the most sophisticated of the manipulators today cannot perform many of the work tasks now performed by divers in shallower waters. Manipulators cannot yet duplicate the functions of the human hand. How much technology must be improved to perform the desired tasks, and how much adapting of the work task or equipment must be done to achieve a workable underwater robotics environment?

Massively parallel mathematical sieves

Energy Technology Data Exchange (ETDEWEB)

Montry, G.R.

1989-01-01

The Sieve of Eratosthenes is a well-known algorithm for finding all prime numbers in a given subset of integers. A parallel version of the Sieve is described that produces computational speedups over 800 on a hypercube with 1,024 processing elements for problems of fixed size. Computational speedups as high as 980 are achieved when the problem size per processor is fixed. The method of parallelization generalizes to other sieves and will be efficient on any ensemble architecture. We investigate two highly parallel sieves using scattered decomposition and compare their performance on a hypercube multiprocessor. A comparison of different parallelization techniques for the sieve illustrates the trade-offs necessary in the design and implementation of massively parallel algorithms for large ensemble computers.

Maintenance and manipulation of information in schizophrenia: further evidence for impairment in the central executive component of working memory.

Science.gov (United States)

Kim, Junghoon; Glahn, David C; Nuechterlein, Keith H; Cannon, Tyrone D

2004-06-01

Impairments in working memory (WM) have been proposed to underlie various cognitive and functional impairments in schizophrenia. However, the nature and extent of the dysfunction remain unclear. The present study attempted to examine the integrity of sub-components of working memory in schizophrenia within the framework of the multiple-component working memory model proposed by Baddeley. Two sets of visuospatial and verbal delayed-response tasks were developed which had comparable formats and difficulties across domains. In Experiment 1, demands on the central executive (CE) were manipulated by requiring subjects either (1) to simultaneously maintain and transform information (maintenance-and-manipulation condition) or (2) just to maintain this information (maintenance-only condition). In Experiment 2, the amount of information to be maintained over the delay was parametrically varied to evaluate demands on the temporary maintenance component of working memory. Patients (N=16) performed worse than controls (N=16) in both conditions of Experiment 1; however, simultaneous maintenance and manipulation was associated with a significantly greater performance reduction in the patients. In Experiment 2, both patients (N=15) and controls (N=15) declined in performance, at equivalent rates, with increasing memory load. Parallel findings were observed for the verbal and visuospatial tasks. These results suggest that while both maintenance and central executive aspects of working memory are impaired in schizophrenic patients, the central executive may be more severely affected.

Computer-Aided Parallelizer and Optimizer

Science.gov (United States)

Jin, Haoqiang

2011-01-01

The Computer-Aided Parallelizer and Optimizer (CAPO) automates the insertion of compiler directives (see figure) to facilitate parallel processing on Shared Memory Parallel (SMP) machines. While CAPO currently is integrated seamlessly into CAPTools (developed at the University of Greenwich, now marketed as ParaWise), CAPO was independently developed at Ames Research Center as one of the components for the Legacy Code Modernization (LCM) project. The current version takes serial FORTRAN programs, performs interprocedural data dependence analysis, and generates OpenMP directives. Due to the widely supported OpenMP standard, the generated OpenMP codes have the potential to run on a wide range of SMP machines. CAPO relies on accurate interprocedural data dependence information currently provided by CAPTools. Compiler directives are generated through identification of parallel loops in the outermost level, construction of parallel regions around parallel loops and optimization of parallel regions, and insertion of directives with automatic identification of private, reduction, induction, and shared variables. Attempts also have been made to identify potential pipeline parallelism (implemented with point-to-point synchronization). Although directives are generated automatically, user interaction with the tool is still important for producing good parallel codes. A comprehensive graphical user interface is included for users to interact with the parallelization process.

Spin-orbit torques for current parallel and perpendicular to a domain wall

Energy Technology Data Exchange (ETDEWEB)

Schulz, Tomek; Lee, Kyujoon; Karnad, Gurucharan V. [Institut für Physik, Johannes Gutenberg-Universität Mainz, Staudinger Weg 7, 55128 Mainz (Germany); Alejos, Oscar [Departamento de Electricidad y Electrónica, Universidad de Valladolid, Paseo de Belen, 7, E-47011 Valladolid (Spain); Martinez, Eduardo; Moretti, Simone [Departamento Fisica Aplicada, Universidad de Salamanca, Plaza de los Caidos s/n, E-38008 Salamanca (Spain); Hals, Kjetil M. D. [Niels Bohr International Academy and the Center for Quantum Devices, Niels Bohr Institute, University of Copenhagen, 2100 Copenhagen (Denmark); Garcia, Karin; Ravelosona, Dafiné [Institut d' Electronique Fondamentale, UMR CNRS 8622, Université Paris Sud, 91405 Orsay Cedex (France); Vila, Laurent [Institut Nanosciences et Cryogénie, Université Grenoble Alpes, F-38000 Grenoble (France); Institut Nanosciences et Cryogénie, CEA, F-38000 Grenoble (France); Lo Conte, Roberto; Kläui, Mathias [Institut für Physik, Johannes Gutenberg-Universität Mainz, Staudinger Weg 7, 55128 Mainz (Germany); Graduate School of Excellence “Materials Science in Mainz” (MAINZ), Staudinger Weg 9, 55128 Mainz (Germany); Ocker, Berthold [Singulus Technologies AG, 63796 Kahl am Main (Germany); Brataas, Arne [Department of Physics, Norwegian University of Science and Technology, NO-7491 Trondheim (Norway)

2015-09-21

We report field- and current-induced domain wall (DW) depinning experiments in Ta\\Co{sub 20}Fe{sub 60}B{sub 20}\\MgO nanowires through a Hall cross geometry. While purely field-induced depinning shows no angular dependence on in-plane fields, the effect of the current depends crucially on the internal DW structure, which we manipulate by an external magnetic in-plane field. We show depinning measurements for a current sent parallel to the DW and compare its depinning efficiency with the conventional case of current flowing perpendicularly to the DW. We find that the maximum efficiency is similar for both current directions within the error bars, which is in line with a dominating damping-like spin-orbit torque (SOT) and indicates that no large additional torques arise for currents perpendicular to the DW. Finally, we find a varying dependence of the maximum depinning efficiency angle for different DWs and pinning levels. This emphasizes the importance of our full angular scans compared with previously used measurements for just two field directions (parallel and perpendicular to the DW) to determine the real torque strength and shows the sensitivity of the SOT to the precise DW structure and pinning sites.

Interpersonal relationship manipulation at a personal level

OpenAIRE

Andreja Hribernik

2010-01-01

Manipulation is not unknown or strange to any of us. We have all experienced it, or perhaps even practiced it. It is wrong not to recognize it, to find excuses for it, and, above all, it is wrong not to decide to change one’s behaviour. Long-lasting use of manipulation leaves consequences on all the parties involved: the victim, the observer and the perpetrator. Manipulation is a relation between persons which does not consider the needs of everybody involved. It means exploitation and mislea...

W-026, acceptance test report manipulator system

International Nuclear Information System (INIS)

Watson, T.L.

1997-01-01

The purpose of the WRAP Manipulator System Acceptance Test Plan (ATP) is to verify that the 4 glovebox sets of WRAP manipulator components, including rail/carriage, slave arm, master controller and auxiliary equipment, meets the requirements of the functional segments of 14590 specification. The demonstration of performance elements of the ATP are performed as a part of the Assembly specifications. Manipulator integration is integrated in the performance testing of the gloveboxes. Each requirement of the Assembly specification will be carried out in conjunction with glovebox performance tests

Emerging Nanophotonic Applications Explored with Advanced Scientific Parallel Computing

Science.gov (United States)

Meng, Xiang

particular, parallel computing are forms of computation operating on the principle that large problems can often be divided into smaller ones, which are then solved concurrently. In this dissertation, we report a series of new nanophotonic developments using the advanced parallel computing techniques. The applications include the structure optimizations at the nanoscale to control both the electromagnetic response of materials, and to manipulate nanoscale structures for enhanced field concentration, which enable breakthroughs in imaging, sensing systems (chapter 3 and 4) and improve the spatial-temporal resolutions of spectroscopies (chapter 5). We also report the investigations on the confinement study of optical-matter interactions at the quantum mechanical regime, where the size-dependent novel properties enhanced a wide range of technologies from the tunable and efficient light sources, detectors, to other nanophotonic elements with enhanced functionality (chapter 6 and 7).

Data communications in a parallel active messaging interface of a parallel computer

Science.gov (United States)

Archer, Charles J; Blocksome, Michael A; Ratterman, Joseph D; Smith, Brian E

2013-11-12

Data communications in a parallel active messaging interface (`PAMI`) of a parallel computer composed of compute nodes that execute a parallel application, each compute node including application processors that execute the parallel application and at least one management processor dedicated to gathering information regarding data communications. The PAMI is composed of data communications endpoints, each endpoint composed of a specification of data communications parameters for a thread of execution on a compute node, including specifications of a client, a context, and a task, the compute nodes and the endpoints coupled for data communications through the PAMI and through data communications resources. Embodiments function by gathering call site statistics describing data communications resulting from execution of data communications instructions and identifying in dependence upon the call cite statistics a data communications algorithm for use in executing a data communications instruction at a call site in the parallel application.

A parallel buffer tree

DEFF Research Database (Denmark)

Sitchinava, Nodar; Zeh, Norbert

2012-01-01

We present the parallel buffer tree, a parallel external memory (PEM) data structure for batched search problems. This data structure is a non-trivial extension of Arge's sequential buffer tree to a private-cache multiprocessor environment and reduces the number of I/O operations by the number of...... in the optimal OhOf(psortN + K/PB) parallel I/O complexity, where K is the size of the output reported in the process and psortN is the parallel I/O complexity of sorting N elements using P processors....

Application Portable Parallel Library

Science.gov (United States)

Cole, Gary L.; Blech, Richard A.; Quealy, Angela; Townsend, Scott

1995-01-01

Application Portable Parallel Library (APPL) computer program is subroutine-based message-passing software library intended to provide consistent interface to variety of multiprocessor computers on market today. Minimizes effort needed to move application program from one computer to another. User develops application program once and then easily moves application program from parallel computer on which created to another parallel computer. ("Parallel computer" also include heterogeneous collection of networked computers). Written in C language with one FORTRAN 77 subroutine for UNIX-based computers and callable from application programs written in C language or FORTRAN 77.

Parallel Algorithms and Patterns

Energy Technology Data Exchange (ETDEWEB)

Robey, Robert W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-16

This is a powerpoint presentation on parallel algorithms and patterns. A parallel algorithm is a well-defined, step-by-step computational procedure that emphasizes concurrency to solve a problem. Examples of problems include: Sorting, searching, optimization, matrix operations. A parallel pattern is a computational step in a sequence of independent, potentially concurrent operations that occurs in diverse scenarios with some frequency. Examples are: Reductions, prefix scans, ghost cell updates. We only touch on parallel patterns in this presentation. It really deserves its own detailed discussion which Gabe Rockefeller would like to develop.

Autonomous Industrial Mobile Manipulation (AIMM)

DEFF Research Database (Denmark)

Hvilshøj, Mads; Bøgh, Simon; Nielsen, Oluf Skov

2012-01-01

Purpose - The purpose of this paper is to provide a review of the interdisciplinary research field Autonomous Industrial Mobile Manipulation (AIMM), with an emphasis on physical implementations and applications. Design/methodology/approach - Following an introduction to AIMM, this paper investiga......Purpose - The purpose of this paper is to provide a review of the interdisciplinary research field Autonomous Industrial Mobile Manipulation (AIMM), with an emphasis on physical implementations and applications. Design/methodology/approach - Following an introduction to AIMM, this paper......; sustainability, configuration, adaptation, autonomy, positioning, manipulation and grasping, robot-robot interaction, human-robot interaction, process quality, dependability, and physical properties. Findings - The concise yet comprehensive review provides both researchers (academia) and practitioners (industry......) with a quick and gentle overview of AIMM. Furthermore, the paper identifies key open issues and promising research directions to realize real-world integration and maturation of the AIMM technology. Originality/value - This paper reviews the interdisciplinary research field Autonomous Industrial Mobile...

ADVERTISING AS MEAN OF MANIPULATION OF PEOPLE

Directory of Open Access Journals (Sweden)

Camelia PAVEL

2014-04-01

Full Text Available The article provides a number of issues involved in defining manipulation, because both in the current language as in the specialty literature, the manipulation notion is used with multiple significations, often contradictory ones, and that it’s not firmly delimited by other notions from the same sphere, like persuasion or propaganda. The aim of the article will be, in the end, removing ambiguity that surrounds this concept and offering a better understanding of its very real effects on human lives. We advance and sustain the hypothesis that manipulation is an illegitimate process, justified by the structure of the human conscience and by the mechanisms of the social life. In addition, the paper provides a concrete example of manipulation of public through advertising contracts offered by Roşia Montană Gold Corporation. Finally conclusions were outlined.

Totally parallel multilevel algorithms

Science.gov (United States)

Frederickson, Paul O.

1988-01-01

Four totally parallel algorithms for the solution of a sparse linear system have common characteristics which become quite apparent when they are implemented on a highly parallel hypercube such as the CM2. These four algorithms are Parallel Superconvergent Multigrid (PSMG) of Frederickson and McBryan, Robust Multigrid (RMG) of Hackbusch, the FFT based Spectral Algorithm, and Parallel Cyclic Reduction. In fact, all four can be formulated as particular cases of the same totally parallel multilevel algorithm, which are referred to as TPMA. In certain cases the spectral radius of TPMA is zero, and it is recognized to be a direct algorithm. In many other cases the spectral radius, although not zero, is small enough that a single iteration per timestep keeps the local error within the required tolerance.

Global Energy-Optimal Redundancy Resolution of Hydraulic Manipulators: Experimental Results for a Forestry Manipulator

Directory of Open Access Journals (Sweden)

Jarmo Nurmi

2017-05-01

Full Text Available This paper addresses the energy-inefficiency problem of four-degrees-of-freedom (4-DOF hydraulic manipulators through redundancy resolution in robotic closed-loop controlled applications. Because conventional methods typically are local and have poor performance for resolving redundancy with respect to minimum hydraulic energy consumption, global energy-optimal redundancy resolution is proposed at the valve-controlled actuator and hydraulic power system interaction level. The energy consumption of the widely popular valve-controlled load-sensing (LS and constant-pressure (CP systems is effectively minimised through cost functions formulated in a discrete-time dynamic programming (DP approach with minimum state representation. A prescribed end-effector path and important actuator constraints at the position, velocity and acceleration levels are also satisfied in the solution. Extensive field experiments performed on a forestry hydraulic manipulator demonstrate the performance of the proposed solution. Approximately 15–30% greater hydraulic energy consumption was observed with the conventional methods in the LS and CP systems. These results encourage energy-optimal redundancy resolution in future robotic applications of hydraulic manipulators.

MA-23-6000: underwater bilateral servo master slave manipulator

International Nuclear Information System (INIS)

Vertut, Jean

The different types of manipulators, recent data on their dexterity and the underwater work possible with servo master slave manipulators are reviewed. The general specifications of the manipulator MA 23-6000 designed for the machine ERIC II are given [fr

Advanced Bimanual Manipulation Results from the DEXMART Project

CERN Document Server

2012-01-01

Dexterous and autonomous manipulation is a key technology for the personal and service robots of the future. Advances in Bimanual Manipulation edited by Bruno Siciliano provides the robotics community with the most noticeable results of the four-year European project DEXMART (DEXterous and autonomous dual-arm hand robotic manipulation with sMART sensory-motor skills: A bridge from natural to artificial cognition). The volume covers a host of highly important topics in the field, concerned with modelling and learning of human manipulation skills, algorithms for task planning, human-robot interaction, and grasping, as well as hardware design of dexterous anthropomorphic hands. The results described in this five-chapter collection are believed to pave the way towards the development of robotic systems endowed with dexterous and human-aware dual-arm/hand manipulation skills for objects, operating with a high degree of autonomy in unstructured real-world environments.

Analysis of singularity in redundant manipulators

International Nuclear Information System (INIS)

Watanabe, Koichi

2000-03-01

In the analysis of arm positions and configurations of redundant manipulators, the singularity avoidance problems are important themes. This report presents singularity avoidance computations of a 7 DOF manipulator by using a computer code based on human-arm models. The behavior of the arm escaping from the singular point can be identified satisfactorily through the use of 3-D plotting tools. (author)

Neural Parallel Engine: A toolbox for massively parallel neural signal processing.

Science.gov (United States)

Tam, Wing-Kin; Yang, Zhi

2018-05-01

Large-scale neural recordings provide detailed information on neuronal activities and can help elicit the underlying neural mechanisms of the brain. However, the computational burden is also formidable when we try to process the huge data stream generated by such recordings. In this study, we report the development of Neural Parallel Engine (NPE), a toolbox for massively parallel neural signal processing on graphical processing units (GPUs). It offers a selection of the most commonly used routines in neural signal processing such as spike detection and spike sorting, including advanced algorithms such as exponential-component-power-component (EC-PC) spike detection and binary pursuit spike sorting. We also propose a new method for detecting peaks in parallel through a parallel compact operation. Our toolbox is able to offer a 5× to 110× speedup compared with its CPU counterparts depending on the algorithms. A user-friendly MATLAB interface is provided to allow easy integration of the toolbox into existing workflows. Previous efforts on GPU neural signal processing only focus on a few rudimentary algorithms, are not well-optimized and often do not provide a user-friendly programming interface to fit into existing workflows. There is a strong need for a comprehensive toolbox for massively parallel neural signal processing. A new toolbox for massively parallel neural signal processing has been created. It can offer significant speedup in processing signals from large-scale recordings up to thousands of channels. Copyright © 2018 Elsevier B.V. All rights reserved.

Sensory-specific clock components and memory mechanisms: investigation with parallel timing.

Science.gov (United States)

Gamache, Pierre-Luc; Grondin, Simon

2010-05-01

A challenge for researchers in the time-perception field is to determine whether temporal processing is governed by a central mechanism or by multiple mechanisms working in concert. Behavioral studies of parallel timing offer interesting insights into the question, although the conclusions fail to converge. Most of these studies focus on the number-of-clocks issue, but the commonality of memory mechanisms involved in time processing is often neglected. The present experiment aims to address a straightforward question: do signals from different modalities marking time intervals share the same clock and/or the same memory resources? To this end, an interval reproduction task involving the parallel timing of two sensory signals presented either in the same modality or in different modalities was conducted. The memory component was tested by manipulating the delay separating the presentation of the target intervals and the moment when the reproduction of one of these began. Results show that there is more variance when only visually marked intervals are presented, and this effect is exacerbated with longer retention delays. Finally, when there is only one interval to process, encoding the interval with signals delivered from two modalities helps to reduce variance. Taken together, these results suggest that the hypothesis stating that there are sensory-specific clock components and memory mechanisms is viable.

A possibility of parallel and anti-parallel diffraction measurements on ...

Indian Academy of Sciences (India)

However, a bent perfect crystal (BPC) monochromator at monochromatic focusing condition can provide a quite flat and equal resolution property at both parallel and anti-parallel positions and thus one can have a chance to use both sides for the diffraction experiment. From the data of the FWHM and the / measured ...

Kinematics at the Main Mechanism of a Railbound Forging Manipulator

Directory of Open Access Journals (Sweden)

Florian Ion Tiberiu Petrescu

2015-09-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Heavy payload forging manipulators are mainly characterized by large load output and large capacitive load input. The relationship between outputs and inputs will greatly influence the control and the reliability. Forging manipulators have become more prevalent in the industry today. They are used to manipulate objects to be forged. The most common forging manipulators are moving on a railway to have a greater precision and stability. They have been called the railbound forging manipulators. In this paper we analyze the general kinematics of the main mechanism from a such manipulator. Kinematic scheme shows a typical forging manipulator, with the basic motions in operation process: walking, motion of the tong and buffering. The lifting mechanism consists of several parts including linkages, hydraulic drives and motion pairs. The principle of type design from the viewpoints of the relationship between output characteristics and actuator inputs is discussed. An idea of establishing the incidence relationship between output characteristics and actuator inputs is proposed. These novel forging manipulators which satisfy certain functional requirements provide an effective help for the design of forging manipulators.

Optical Manipulation System Using a Plurality of Optical Traps

DEFF Research Database (Denmark)

2006-01-01

The present invention relates to an optical manipulation system (10) for generation of a plurality of optical traps for manipulation of micro-objects including nano-objects using electromagnetic radiation forces in a micro-object manipulation volume (14), the system comprising a spatially modulat...

WORKSPACE DRAWING FROM A MANIPULATOR ARM WITH 6 DOF

Directory of Open Access Journals (Sweden)

NAIDIN Gigi

2011-06-01

Full Text Available Modelling and simulation is an important aspect in robotic field. Knowing of the workspace is very important to the operation of manipulators arm. This paper investigates operational performance of space manipulator arm destined for industrial manufacturing, by defining and analyzing their workspace and manipulability measure. The authors show that manipulator arm developing requires the consideration of more efficient dynamic models and use of dedicated processing techniques such as Autodesk-Inventor 9, MATLAB, WorkSpace software.

Vehicle-manipulator systems modeling for simulation, analysis, and control

CERN Document Server

From, Pal Johan; Pettersen, Kristin Ytterstad

2014-01-01

Furthering the aim of reducing human exposure to hazardous environments, this monograph presents a detailed study of the modeling and control of vehicle-manipulator systems. The text shows how complex interactions can be performed at remote locations using systems that combine the manipulability of robotic manipulators with the ability of mobile robots to locomote over large areas.  The first part studies the kinematics and dynamics of rigid bodies and standard robotic manipulators and can be used as an introduction to robotics focussing on robust mathematical modeling. The monograph then moves on to study vehicle-manipulator systems in great detail with emphasis on combining two different configuration spaces in a mathematically sound way. Robustness of these systems is extremely important and Modeling and Control of Vehicle-manipulator Systems effectively represents the dynamic equations using a mathematically robust framework. Several tools from Lie theory and differential geometry are used to obtain glob...

Protozoa manipulation by ultrasound

Directory of Open Access Journals (Sweden)

Yancy Milena Porras Rodríguez

2004-01-01

Full Text Available Microorganism manipulation, considered as controlled motion and positioning, is one of the most important activities in microbiology and medicine. To achieve this goal there are some techniques such as those which and optical forces, among others. These techniques are usually sophisticated, and some of them can induce irreversible alterations on the microorganisms which prevents their use in another tests. Thus, there is justified the study of technological alternatives to manipulate microorganisms in an easy and cost-effective way. This work shows the interaction between protozoa and air microbubbles when they are under the influence of an ultrasonic field of 5.8 mW. At the microbubbles resonant frequencies, microorganisms were attracted toward the bubbles' frontier remaining there while the ultrasonic field was applied. Once the ultrasound disappears, protozoa recover their freedom of movement. The observed effects could be used as the actuation principle of devices capable to trap, hold and release microorganisms of high mobility without any apparent damage. Microbubbles are generated by electrolysis which take place on the surface of an electrode array, while the ultrasound is originated by means of a piezoelectric transducer. As microorganisms there were employed those present in stagnated water, and were observed through an stereomicroscope. Key words: manipulator; protozoa; ultrasonic; transducer; piezoelectric.

Getting Manipulative about Math.

Science.gov (United States)

Scheer, Janet K.; And Others

1984-01-01

Math manipulatives that are made from inexpensive, common items help students understand basic mathematics concepts. Learning activities using Cheerios, jellybeans, and clay as teaching materials are suggested. (DF)

Parallel implementation of the PHOENIX generalized stellar atmosphere program. II. Wavelength parallelization

International Nuclear Information System (INIS)

Baron, E.; Hauschildt, Peter H.

1998-01-01

We describe an important addition to the parallel implementation of our generalized nonlocal thermodynamic equilibrium (NLTE) stellar atmosphere and radiative transfer computer program PHOENIX. In a previous paper in this series we described data and task parallel algorithms we have developed for radiative transfer, spectral line opacity, and NLTE opacity and rate calculations. These algorithms divided the work spatially or by spectral lines, that is, distributing the radial zones, individual spectral lines, or characteristic rays among different processors and employ, in addition, task parallelism for logically independent functions (such as atomic and molecular line opacities). For finite, monotonic velocity fields, the radiative transfer equation is an initial value problem in wavelength, and hence each wavelength point depends upon the previous one. However, for sophisticated NLTE models of both static and moving atmospheres needed to accurately describe, e.g., novae and supernovae, the number of wavelength points is very large (200,000 - 300,000) and hence parallelization over wavelength can lead both to considerable speedup in calculation time and the ability to make use of the aggregate memory available on massively parallel supercomputers. Here, we describe an implementation of a pipelined design for the wavelength parallelization of PHOENIX, where the necessary data from the processor working on a previous wavelength point is sent to the processor working on the succeeding wavelength point as soon as it is known. Our implementation uses a MIMD design based on a relatively small number of standard message passing interface (MPI) library calls and is fully portable between serial and parallel computers. copyright 1998 The American Astronomical Society

Manipulation of the Commodity Futures Market Delivery Process.

OpenAIRE

Pirrong, Stephen Craig

1993-01-01

An analysis of the futures market delivery 'end game' specifies necessary and sufficient conditions for long and short traders to manipulate futures prices at contract expiration. The empirical and welfare implications of manipulation are derived as well. Manipulation is most likely to occur in markets where economic frictions (such as transportation and transactions costs) make it inefficient to return excessive deliveries to their original owners. These consumption distortions induce price ...

Parallel Syndromes: Two Dimensions of Narcissism and the Facets of Psychopathic Personality in Criminally-Involved Individuals

Science.gov (United States)

2012-01-01

Little research has examined different dimensions of narcissism that may parallel psychopathy facets in criminally-involved individuals. The present study examined the pattern of relationships between grandiose and vulnerable narcissism, assessed using the Narcissistic Personality Inventory-16 and the Hypersensitive Narcissism Scale, respectively, and the four facets of psychopathy (interpersonal, affective, lifestyle, and antisocial) assessed via the Psychopathy Checklist: Screening Version (PCL:SV). As predicted, grandiose and vulnerable narcissism showed differential relationships to psychopathy facets, with grandiose narcissism relating positively to the interpersonal facet of psychopathy and vulnerable narcissism relating positively to the lifestyle facet of psychopathy. Paralleling existing psychopathy research, vulnerable narcissism showed stronger associations than grandiose narcissism to 1) other forms of psychopathology, including internalizing and substance use disorders, and 2) self- and other-directed aggression, measured using the Life History of Aggression and the Forms of Aggression Questionnaire. Grandiose narcissism was nonetheless associated with social dysfunction marked by a manipulative and deceitful interpersonal style and unprovoked aggression. Potentially important implications for uncovering etiological pathways and developing treatment interventions for these disorders in externalizing adults are discussed. PMID:22448731

Even Middle Graders Can Learn with Manipulatives.

Science.gov (United States)

Holden, Linda

1987-01-01

Math manipulatives let students see the components of an abstract problem, help build a concrete language for talking about math concepts, and encourage students to gain confidence in their ability to figure things out. Many suggestions for using manipulatives in math instruction are offered. (MT)

Tools for Manipulation and Characterisation of Nanostructures

DEFF Research Database (Denmark)

Mølhave, Kristian; Bøggild, Peter

grippers, which were then successfully used for pick-and-place manipulation of silicon nanowires. For increased gripping force and control over the manipulation process, microfabricated grippers with integrated force-feedback were also demonstrated. Environmental electron beam deposition (EEBD...... components that are some 10000 times smaller....

Short-term combined effects of thoracic spine thrust manipulation and cervical spine nonthrust manipulation in individuals with mechanical neck pain: a randomized clinical trial.

Science.gov (United States)

Masaracchio, Michael; Cleland, Joshua A; Hellman, Madeleine; Hagins, Marshall

2013-03-01

Randomized clinical trial. To investigate the short-term effects of thoracic spine thrust manipulation combined with cervical spine nonthrust manipulation (experimental group) versus cervical spine nonthrust manipulation alone (comparison group) in individuals with mechanical neck pain. Research has demonstrated improved outcomes with both nonthrust manipulation directed at the cervical spine and thrust manipulation directed at the thoracic spine in patients with neck pain. Previous studies have not determined if thoracic spine thrust manipulation may increase benefits beyond those provided by cervical nonthrust manipulation alone. Sixty-four participants with mechanical neck pain were randomized into 1 of 2 groups, an experimental or comparison group. Both groups received 2 treatment sessions of cervical spine nonthrust manipulation and a home exercise program consisting of active range-of-motion exercises, and the experimental group received additional thoracic spine thrust manipulations. Outcome measures were collected at baseline and at a 1-week follow-up, and included the numeric pain rating scale, the Neck Disability Index, and the global rating of change. Participants in the experimental group demonstrated significantly greater improvements (Ppain rating scale and Neck Disability Index at the 1-week follow-up compared to those in the comparison group. In addition, 31 of 33 (94%) participants in the experimental group, compared to 11 of 31 participants (35%) in the comparison group, indicated a global rating of change score of +4 or higher at the 1-week follow-up, with an associated number needed to treat of 2. Individuals with neck pain who received a combination of thoracic spine thrust manipulation and cervical spine nonthrust manipulation plus exercise demonstrated better overall short-term outcomes on the numeric pain rating scale, the Neck Disability Index, and the global rating of change.

Development of the heavy manipulator vehicle system

International Nuclear Information System (INIS)

Herbst, C.; Paustian, P.; Kruger, W.

1993-01-01

After the severe reactor accident of Tschernobyl in 1986 MaK System started to develop a Heavy Manipulator Vehicle System under contract from German nuclear technology assistance company ''KHG'' (Kerntechnische Hilfsdienst GmbH). The system comprises a remote controlled manipulator vehicle, a mobile mission control stand as well as a transport/service unit. In order to fulfill the high demands of this complex system a couple of new developments had to be started. The paper describes some of these developments and gives an overview about the main features of the Heavy Manipulator Vehicle System (HMV). (author)

Completion of the Heysham 2 peripheral manipulator

International Nuclear Information System (INIS)

Shipp, R.; Ewen, R.O.

1996-01-01

The in-service inspection strategy for the AGR power station at Heysham 2 envisaged a suite of five manipulators to be used for inserting TRIUMPH television cameras into the reactor vessel. Prior to power raising, four of the five had been successfully commissioned and have been in regular use during the subsequent statutory outages. The final device, the Peripheral Manipulator (PM), was eventually completed prior to the 1994 outage and has been successfully deployed on reactor for both the 1994 and 1995 outages. The paper describes the design of the manipulator, its operation and scope of use in the Heysham 2 reactors. (Author)

Parallel k-means++

Energy Technology Data Exchange (ETDEWEB)

2017-04-04

A parallelization of the k-means++ seed selection algorithm on three distinct hardware platforms: GPU, multicore CPU, and multithreaded architecture. K-means++ was developed by David Arthur and Sergei Vassilvitskii in 2007 as an extension of the k-means data clustering technique. These algorithms allow people to cluster multidimensional data, by attempting to minimize the mean distance of data points within a cluster. K-means++ improved upon traditional k-means by using a more intelligent approach to selecting the initial seeds for the clustering process. While k-means++ has become a popular alternative to traditional k-means clustering, little work has been done to parallelize this technique. We have developed original C++ code for parallelizing the algorithm on three unique hardware architectures: GPU using NVidia's CUDA/Thrust framework, multicore CPU using OpenMP, and the Cray XMT multithreaded architecture. By parallelizing the process for these platforms, we are able to perform k-means++ clustering much more quickly than it could be done before.

Parallel magnetic resonance imaging

International Nuclear Information System (INIS)

Larkman, David J; Nunes, Rita G

2007-01-01

Parallel imaging has been the single biggest innovation in magnetic resonance imaging in the last decade. The use of multiple receiver coils to augment the time consuming Fourier encoding has reduced acquisition times significantly. This increase in speed comes at a time when other approaches to acquisition time reduction were reaching engineering and human limits. A brief summary of spatial encoding in MRI is followed by an introduction to the problem parallel imaging is designed to solve. There are a large number of parallel reconstruction algorithms; this article reviews a cross-section, SENSE, SMASH, g-SMASH and GRAPPA, selected to demonstrate the different approaches. Theoretical (the g-factor) and practical (coil design) limits to acquisition speed are reviewed. The practical implementation of parallel imaging is also discussed, in particular coil calibration. How to recognize potential failure modes and their associated artefacts are shown. Well-established applications including angiography, cardiac imaging and applications using echo planar imaging are reviewed and we discuss what makes a good application for parallel imaging. Finally, active research areas where parallel imaging is being used to improve data quality by repairing artefacted images are also reviewed. (invited topical review)

Parallel symbolic state-space exploration is difficult, but what is the alternative?

Directory of Open Access Journals (Sweden)

Gianfranco Ciardo

2009-12-01

Full Text Available State-space exploration is an essential step in many modeling and analysis problems. Its goal is to find the states reachable from the initial state of a discrete-state model described. The state space can used to answer important questions, e.g., "Is there a dead state?" and "Can N become negative?", or as a starting point for sophisticated investigations expressed in temporal logic. Unfortunately, the state space is often so large that ordinary explicit data structures and sequential algorithms cannot cope, prompting the exploration of (1 parallel approaches using multiple processors, from simple workstation networks to shared-memory supercomputers, to satisfy large memory and runtime requirements and (2 symbolic approaches using decision diagrams to encode the large structured sets and relations manipulated during state-space generation. Both approaches have merits and limitations. Parallel explicit state-space generation is challenging, but almost linear speedup can be achieved; however, the analysis is ultimately limited by the memory and processors available. Symbolic methods are a heuristic that can efficiently encode many, but not all, functions over a structured and exponentially large domain; here the pitfalls are subtler: their performance varies widely depending on the class of decision diagram chosen, the state variable order, and obscure algorithmic parameters. As symbolic approaches are often much more efficient than explicit ones for many practical models, we argue for the need to parallelize symbolic state-space generation algorithms, so that we can realize the advantage of both approaches. This is a challenging endeavor, as the most efficient symbolic algorithm, Saturation, is inherently sequential. We conclude by discussing challenges, efforts, and promising directions toward this goal.

A digital joint controller for manipulators

International Nuclear Information System (INIS)

Holt, E.J.; Palmer, D.E.B.

1993-01-01

Nuclear Electric's hydraulic heavy duty manipulators are used at a number of Magnox Power Stations for a wide variety of tasks. In recent years there has been a trend towards the use of manipulators for tasks requiring increasing precision of tip positioning. In order to meet this requirement, a digital controller has been designed to replace the analogue controller board used in almost all manipulator control systems. The new controller allows the programming of a wide range of closed loop control algorithms. Position and drive signal data may be passed to and from the controller by digital means, allowing direct connection to a graphical display system and/or a computer executing a guidance algorithm. The hardware and software design are outlined and performance in the laboratory and the field is reported. (author)

Experiences in Data-Parallel Programming

Directory of Open Access Journals (Sweden)

Terry W. Clark

1997-01-01

Full Text Available To efficiently parallelize a scientific application with a data-parallel compiler requires certain structural properties in the source program, and conversely, the absence of others. A recent parallelization effort of ours reinforced this observation and motivated this correspondence. Specifically, we have transformed a Fortran 77 version of GROMOS, a popular dusty-deck program for molecular dynamics, into Fortran D, a data-parallel dialect of Fortran. During this transformation we have encountered a number of difficulties that probably are neither limited to this particular application nor do they seem likely to be addressed by improved compiler technology in the near future. Our experience with GROMOS suggests a number of points to keep in mind when developing software that may at some time in its life cycle be parallelized with a data-parallel compiler. This note presents some guidelines for engineering data-parallel applications that are compatible with Fortran D or High Performance Fortran compilers.

Non-Cartesian parallel imaging reconstruction.

Science.gov (United States)

Wright, Katherine L; Hamilton, Jesse I; Griswold, Mark A; Gulani, Vikas; Seiberlich, Nicole

2014-11-01

Non-Cartesian parallel imaging has played an important role in reducing data acquisition time in MRI. The use of non-Cartesian trajectories can enable more efficient coverage of k-space, which can be leveraged to reduce scan times. These trajectories can be undersampled to achieve even faster scan times, but the resulting images may contain aliasing artifacts. Just as Cartesian parallel imaging can be used to reconstruct images from undersampled Cartesian data, non-Cartesian parallel imaging methods can mitigate aliasing artifacts by using additional spatial encoding information in the form of the nonhomogeneous sensitivities of multi-coil phased arrays. This review will begin with an overview of non-Cartesian k-space trajectories and their sampling properties, followed by an in-depth discussion of several selected non-Cartesian parallel imaging algorithms. Three representative non-Cartesian parallel imaging methods will be described, including Conjugate Gradient SENSE (CG SENSE), non-Cartesian generalized autocalibrating partially parallel acquisition (GRAPPA), and Iterative Self-Consistent Parallel Imaging Reconstruction (SPIRiT). After a discussion of these three techniques, several potential promising clinical applications of non-Cartesian parallel imaging will be covered. © 2014 Wiley Periodicals, Inc.

Manipulator techniques and problems of their application in primary circuit maintenance

International Nuclear Information System (INIS)

Kertscher, F.; Popp, P.

1985-01-01

The fundamental structure and specifications of manipulators (in particular of industrial robots) are presented in order to derive the application conditions and fields for manipulators in primary circuit maintenance. The necessity of applying process-specific manipulator technique in the primary circuit maintenance is based on nuclear safety requirements and on decreasing of the radiation exposure of maintenance personnel. Synchronous manipulators and industrial robots are the types of manipulators used in materials testing, repairing and scrapping. The technical requirements of manipulators are discussed

Influence of Paralleling Dies and Paralleling Half-Bridges on Transient Current Distribution in Multichip Power Modules

DEFF Research Database (Denmark)

Li, Helong; Zhou, Wei; Wang, Xiongfei

2018-01-01

This paper addresses the transient current distribution in the multichip half-bridge power modules, where two types of paralleling connections with different current commutation mechanisms are considered: paralleling dies and paralleling half-bridges. It reveals that with paralleling dies, both t...

A universal microscope manipulator

Directory of Open Access Journals (Sweden)

Peter S. Boyadzhiev

2012-03-01

Full Text Available A modified and improved model of a mechanical manipulator for observation of pinned and mounted insects is described. This device allows movement of the observed object around three perpendicular axes in the field of vision at all magnifications of stereomicroscopes. The main improvement of this new model is positioning of the guiding knobs for rotating around two of the axes next to each other, allowing faster and easier manipulation of the studied object. Thus, one of the main advantages of this device is the possibility to rotate the specimen without the need to refocus. The device enables easily reaching a precession deviation in the intersection point of axes up to 0.5 mm in the process of assembling.

The Effects on Students' Conceptual Understanding of Electric Circuits of Introducing Virtual Manipulatives within a Physical Manipulatives-Oriented Curriculum

Science.gov (United States)

Zacharia, Zacharias C.; de Jong, Ton

2014-01-01

This study investigates whether Virtual Manipulatives (VM) within a Physical Manipulatives (PM)-oriented curriculum affect conceptual understanding of electric circuits and related experimentation processes. A pre-post comparison study randomly assigned 194 undergraduates in an introductory physics course to one of five conditions: three…

Manipulating Combinatorial Structures.

Science.gov (United States)

Labelle, Gilbert

This set of transparencies shows how the manipulation of combinatorial structures in the context of modern combinatorics can easily lead to interesting teaching and learning activities at every level of education from elementary school to university. The transparencies describe: (1) the importance and relations of combinatorics to science and…

A randomized clinical trial to compare the immediate effects of seated thoracic manipulation and targeted supine thoracic manipulation on cervical spine flexion range of motion and pain.

Science.gov (United States)

Karas, Steve; Olson Hunt, Megan J

2014-05-01

Randomized clinical trial. To determine the effectiveness of seated thoracic manipulation versus targeted supine thoracic manipulation on cervical spine pain and flexion range of motion (ROM). There is evidence that thoracic spine manipulation is an effective treatment for patients with cervical spine pain. This evidence includes a variety of techniques to manipulate the thoracic spine. Although each of them is effective, no research has compared techniques to determine which produces the best outcomes. A total of 39 patients with cervical spine pain were randomly assigned to either a seated thoracic manipulation or targeted supine thoracic manipulation group. Pain and flexion ROM measures were taken before and after the intervention. Pain reduction (post-treatment-pre-treatment) was significantly greater in those patients receiving the targeted supine thoracic manipulation compared to the seated thoracic manipulation (Pmanipulation group. The results of this study indicate that a targeted supine thoracic manipulation may be more effective in reducing cervical spine pain and improving cervical flexion ROM than a seated thoracic manipulation. Future studies should include a variety of patients and physical therapists (PTs) to validate our findings.

Tensor contraction engine: Abstraction and automated parallel implementation of configuration-interaction, coupled-cluster, and many-body perturbation theories

International Nuclear Information System (INIS)

Hirata, So

2003-01-01

We develop a symbolic manipulation program and program generator (Tensor Contraction Engine or TCE) that automatically derives the working equations of a well-defined model of second-quantized many-electron theories and synthesizes efficient parallel computer programs on the basis of these equations. Provided an ansatz of a many-electron theory model, TCE performs valid contractions of creation and annihilation operators according to Wick's theorem, consolidates identical terms, and reduces the expressions into the form of multiple tensor contractions acted by permutation operators. Subsequently, it determines the binary contraction order for each multiple tensor contraction with the minimal operation and memory cost, factorizes common binary contractions (defines intermediate tensors), and identifies reusable intermediates. The resulting ordered list of binary tensor contractions, additions, and index permutations is translated into an optimized program that is combined with the NWChem and UTChem computational chemistry software packages. The programs synthesized by TCE take advantage of spin symmetry, Abelian point-group symmetry, and index permutation symmetry at every stage of calculations to minimize the number of arithmetic operations and storage requirement, adjust the peak local memory usage by index range tiling, and support parallel I/O interfaces and dynamic load balancing for parallel executions. We demonstrate the utility of TCE through automatic derivation and implementation of parallel programs for various models of configuration-interaction theory (CISD, CISDT, CISDTQ), many-body perturbation theory[MBPT(2), MBPT(3), MBPT(4)], and coupled-cluster theory (LCCD, CCD, LCCSD, CCSD, QCISD, CCSDT, and CCSDTQ)

Manipulation of Biofilm Microbial Ecology

Energy Technology Data Exchange (ETDEWEB)

White, D.C.; Palmer, R.J., Jr.; Zinn, M.; Smith, C.A.; Burkhalter, R.; Macnaughton, S.J.; Whitaker, K.W.; Kirkegaard, R.D.

1998-08-15

The biofilm mode of growth provides such significant advantages to the members of the consortium that most organisms in important habitats are found in biofilms. The study of factors that allow manipulation of biofilm microbes in the biofilm growth state requires that reproducible biofilms be generated. The most effective monitoring of biofilm formation, succession and desaturation is with on-line monitoring of microbial biofilms with flowcell for direct observation. The biofilm growth state incorporates a second important factor, the heterogeneity in distribution in time and space of the component members of the biofilm consortium. This heterogeneity is reflected not only in the cellular distribution but in the metabolic activity within a population of cells. Activity and cellular distribution can be mapped in four dimensions with confocal microscopy, and function can be ascertained by genetically manipulated reporter functions for specific genes or by vital stains. The methodology for understanding the microbial ecology of biofilms is now much more readily available and the capacity to manipulate biofilms is becoming an important feature of biotechnology.

Manipulation Robustness of Collaborative Filtering Systems

OpenAIRE

Benjamin Van Roy; Xiang Yan

2009-01-01

A collaborative filtering system recommends to users products that similar users like. Collaborative filtering systems influence purchase decisions, and hence have become targets of manipulation by unscrupulous vendors. We provide theoretical and empirical results demonstrating that while common nearest neighbor algorithms, which are widely used in commercial systems, can be highly susceptible to manipulation, two classes of collaborative filtering algorithms which we refer to as linear and a...

Remote Decontamination Facility and Repair Station for hot-cell manipulators

International Nuclear Information System (INIS)

Ryz, M.A.

1977-01-01

Increasingly high radiation levels on manipulators at the Whiteshell Nuclear Research Establishment, Pinawa, Manitoba, Canada, necessitated design and construction of a Remote Decontamination Facility and Repair Station. This facility reduces radiation levels on manipulators by an order of magnitude over previous hand decontamination techniques. The reduced radiation levels have allowed superior manipulator repair and maintenance, resulting in 50% fewer manipulator breakdowns

Parallel Architectures and Parallel Algorithms for Integrated Vision Systems. Ph.D. Thesis

Science.gov (United States)

Choudhary, Alok Nidhi

1989-01-01

Computer vision is regarded as one of the most complex and computationally intensive problems. An integrated vision system (IVS) is a system that uses vision algorithms from all levels of processing to perform for a high level application (e.g., object recognition). An IVS normally involves algorithms from low level, intermediate level, and high level vision. Designing parallel architectures for vision systems is of tremendous interest to researchers. Several issues are addressed in parallel architectures and parallel algorithms for integrated vision systems.

A new approach to adaptive control of manipulators

Science.gov (United States)

Seraji, H.

1987-01-01

An approach in which the manipulator inverse is used as a feedforward controller is employed in the adaptive control of manipulators in order to achieve trajectory tracking by the joint angles. The desired trajectory is applied as an input to the feedforward controller, and the controller output is used as the driving torque for the manipulator. An adaptive algorithm obtained from MRAC theory is used to update the controller gains to cope with variations in the manipulator inverse due to changes of the operating point. An adaptive feedback controller and an auxiliary signal enhance closed-loop stability and achieve faster adaptation. Simulation results demonstrate the effectiveness of the proposed control scheme for different reference trajectories, and despite large variations in the payload.

Pattern-Driven Automatic Parallelization

Directory of Open Access Journals (Sweden)

Christoph W. Kessler

1996-01-01

Full Text Available This article describes a knowledge-based system for automatic parallelization of a wide class of sequential numerical codes operating on vectors and dense matrices, and for execution on distributed memory message-passing multiprocessors. Its main feature is a fast and powerful pattern recognition tool that locally identifies frequently occurring computations and programming concepts in the source code. This tool also works for dusty deck codes that have been "encrypted" by former machine-specific code transformations. Successful pattern recognition guides sophisticated code transformations including local algorithm replacement such that the parallelized code need not emerge from the sequential program structure by just parallelizing the loops. It allows access to an expert's knowledge on useful parallel algorithms, available machine-specific library routines, and powerful program transformations. The partially restored program semantics also supports local array alignment, distribution, and redistribution, and allows for faster and more exact prediction of the performance of the parallelized target code than is usually possible.

Data communications in a parallel active messaging interface of a parallel computer

Science.gov (United States)

Archer, Charles J; Blocksome, Michael A; Ratterman, Joseph D; Smith, Brian E

2013-10-29

Data communications in a parallel active messaging interface (`PAMI`) of a parallel computer, the parallel computer including a plurality of compute nodes that execute a parallel application, the PAMI composed of data communications endpoints, each endpoint including a specification of data communications parameters for a thread of execution on a compute node, including specifications of a client, a context, and a task, the compute nodes and the endpoints coupled for data communications through the PAMI and through data communications resources, including receiving in an origin endpoint of the PAMI a data communications instruction, the instruction characterized by an instruction type, the instruction specifying a transmission of transfer data from the origin endpoint to a target endpoint and transmitting, in accordance with the instruction type, the transfer data from the origin endpoint to the target endpoint.

The STAPL Parallel Graph Library

KAUST Repository

Harshvardhan,; Fidel, Adam; Amato, Nancy M.; Rauchwerger, Lawrence

2013-01-01

This paper describes the stapl Parallel Graph Library, a high-level framework that abstracts the user from data-distribution and parallelism details and allows them to concentrate on parallel graph algorithm development. It includes a customizable

Manipulator for rotating and translating a sample holder

Science.gov (United States)

van de Water, Jeroen [Breugel, NL; van den Oetelaar, Johannes [Eindhoven, NL; Wagner, Raymond [Gorinchem, NL; Slingerland, Hendrik Nicolaas [Venlo, NL; Bruggers, Jan Willem [Eindhoven, NL; Ottevanger, Adriaan Huibert Dirk [Malden, NL; Schmid, Andreas [Berkeley, CA; Olson, Eric A [Champaign, IL; Petrov, Ivan G [Champaign, IL; Donchev, Todor I [Urbana, IL; Duden, Thomas [Kensington, CA

2011-02-08

A manipulator for use in e.g. a Transmission Electron Microscope (TEM) is described, said manipulator capable of rotating and translating a sample holder (4). The manipulator clasps the round sample holder between two members (3A, 3B), said members mounted on actuators (2A, 2B). Moving the actuators in the same direction results in a translation of the sample holder, while moving the actuators in opposite directions results in a rotation of the sample holder.

Machine Learnig for Robotic Manipulation in cluttered environments

OpenAIRE

Alet Puig, Ferran

2016-01-01

In this thesis we focus on designing the planner for MIT s entry in the Amazon Picking Challenge, a robotic competition aiming at pushing the frontiers of manipulation until robots can substitute human pickers in warehouses. Given a set of manipulation primitives (such as grasping, suction, scooping, placing or pushing) we designed a system capable of learning a planner from a set of manipulation experiments. After learning, given any configuration of objects, the planner can come up with the...

Parallelism and array processing

International Nuclear Information System (INIS)

Zacharov, V.

1983-01-01

Modern computing, as well as the historical development of computing, has been dominated by sequential monoprocessing. Yet there is the alternative of parallelism, where several processes may be in concurrent execution. This alternative is discussed in a series of lectures, in which the main developments involving parallelism are considered, both from the standpoint of computing systems and that of applications that can exploit such systems. The lectures seek to discuss parallelism in a historical context, and to identify all the main aspects of concurrency in computation right up to the present time. Included will be consideration of the important question as to what use parallelism might be in the field of data processing. (orig.)

Nonlinear Dynamics of Controlled Synchronizations of Manipulator System

Directory of Open Access Journals (Sweden)

Qingkai Han

2014-01-01

Full Text Available The nonlinear dynamics of the manipulator system which is controlled to achieve the synchronization motions is investigated in the paper. Firstly, the control strategies and modeling approaches of the manipulator system are given, in which the synchronization goal is defined by both synchronization errors and its derivatives. The synchronization controllers applied on the manipulator system include neuron synchronization controller, improved OPCL synchronization controller, and MRAC-PD synchronization controller. Then, an improved adaptive synchronized control strategy is proposed in order to estimate online the unknown structure parameters and state variables of the manipulator system and to realize the needed synchronous compensation. Furthermore, a robust adaptive synchronization controller is also researched to guarantee the dynamic stability of the system. Finally, the stability of motion synchronizations of the manipulator system possessing nonlinear component is discussed, together with the effect of control parameters and joint friction and others. Some typical motions such as motion bifurcations and the loss of synchronization of it are obtained and illustrated as periodic, multiperiodic, and/or chaotic motion patterns.

Particle manipulation techniques in AEgIS

Energy Technology Data Exchange (ETDEWEB)

Canali, C., E-mail: canali@ge.infn.it; Carraro, C.; Di Noto, L.; Krasnicky, D.; Lagomarsino, V.; Testera, G.; Zavatarelli, S. [Istituto Nazionale Fisica Nucleare Sez. Genova (Italy)

2011-07-15

The AEgIS experiment (http://aegis.web.cern.chhttp://aegis.web.cern.ch) will measure the gravitational acceleration g of antihydrogen. Once performed this could be the first direct test of the gravitational interaction between matter and antimatter. In the AEgIS experiment a beam of antihydrogen will travel horizontally along a path of about 1 m trough a moire deflectometer followed by a position sensitive detector. The g value will be obtained measuring the vertical displacement of the annihilation patterns. Before producing the beam, several tasks have to be performed mainly involving positron and electron plasma manipulation and particles cooling in Malmberg-Penning traps. The AEgIS experiment is currently under construction at CERN, meanwhile several tests involving particle manipulation and particle cooling are in progress. In this report some experimental results involving diocotron manipulation of plasma will be presented.

Nonlinear Control of Hydraulic Manipulator for Decommissioning Nuclear Reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Myoung-Ho; Lee, Sung-Uk; Kim, Chang-Hoi; Choi, Byung-Seon; Moon, Jei-Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Robot technique is need to decommission nuclear reactor because of high radiation environment. Especially, Manipulator systems are useful for dismantling complex structure in a nuclear facility. In addition, Hydraulic system is applied to handle heavy duty object. Since hydraulic system can demonstrate high power. The manipulator with hydraulic power is already developed. To solve this problem, various nonlinear control method includes acceleration control. But, it is difficult because acceleration value is highly noisy. In this paper, the nonlinear control algorithm without acceleration control is studied. To verify, the hydraulic manipulator model had been developed. Furthermore, the numerical simulation is carried out. The nonlinear control without acceleration parameter method is developed for hydraulic manipulator. To verify control algorithm, the manipulator is modeled by MBD and the hydraulic servo system is also derived. In addition, the numerical simulation is also carried out. Especially, PID gain is determined though TDC algorithm. In the result of numerical simulation, tracking performance is good without acceleration control. Thus, the PID though TDC with SMC is good for hydraulic manipulator control.

Nonlinear Control of Hydraulic Manipulator for Decommissioning Nuclear Reactor

International Nuclear Information System (INIS)

Kim, Myoung-Ho; Lee, Sung-Uk; Kim, Chang-Hoi; Choi, Byung-Seon; Moon, Jei-Kwon

2016-01-01

Robot technique is need to decommission nuclear reactor because of high radiation environment. Especially, Manipulator systems are useful for dismantling complex structure in a nuclear facility. In addition, Hydraulic system is applied to handle heavy duty object. Since hydraulic system can demonstrate high power. The manipulator with hydraulic power is already developed. To solve this problem, various nonlinear control method includes acceleration control. But, it is difficult because acceleration value is highly noisy. In this paper, the nonlinear control algorithm without acceleration control is studied. To verify, the hydraulic manipulator model had been developed. Furthermore, the numerical simulation is carried out. The nonlinear control without acceleration parameter method is developed for hydraulic manipulator. To verify control algorithm, the manipulator is modeled by MBD and the hydraulic servo system is also derived. In addition, the numerical simulation is also carried out. Especially, PID gain is determined though TDC algorithm. In the result of numerical simulation, tracking performance is good without acceleration control. Thus, the PID though TDC with SMC is good for hydraulic manipulator control

The application of manipulator robot for nuclear power plant maintenance

International Nuclear Information System (INIS)

Fujita, Jun; Onishi, Ken

2009-01-01

In the maintenance works at nuclear power plant, robots are used because of high radiation, narrow space and underwater work. In light of manufacture period, cost and reliability, various maintenance works are requested to be done by one robot. As one of the solutions, we developed manipulator robots for the access of specialized tools. This study shows manipulator robots developed by MHI, application example to maintenance works and effectiveness of manipulator robots. When robotization of maintenance works are considered, manipulator technology is very effective solution means. The manipulator technologies in this study are able to apply to robotization needed under radiation environment. (author)

Manipulator vehicles and loading shovels

International Nuclear Information System (INIS)

Brudermueller, G.; Krueger, W.

1992-01-01

Kerntechnische Hilfsdienst GmbH (KHG) is an institution jointly founded by electricity utilities, fuel cycle industries, and national research centers to provide specialist equipment for removing the consequences of accidents inside plants and recognizing damage in the immediate vicinity of such plants, maintain such equipment in an operational condition, and provide personnel instructed in work of this kind. The specialized technical equipment developed includes carriages, carrier vehicles for manipulators, grabs, TV cameras or measuring gear. In addition to manipulator vehicles, especially loading shovels are used. Radio-controlled vehicles are used where cable operation is either not reliable enough or has failed. (orig.) [de

Vectorization, parallelization and porting of nuclear codes (vectorization and parallelization). Progress report fiscal 1998

International Nuclear Information System (INIS)

Ishizuki, Shigeru; Kawai, Wataru; Nemoto, Toshiyuki; Ogasawara, Shinobu; Kume, Etsuo; Adachi, Masaaki; Kawasaki, Nobuo; Yatake, Yo-ichi

2000-03-01

Several computer codes in the nuclear field have been vectorized, parallelized and transported on the FUJITSU VPP500 system, the AP3000 system and the Paragon system at Center for Promotion of Computational Science and Engineering in Japan Atomic Energy Research Institute. We dealt with 12 codes in fiscal 1998. These results are reported in 3 parts, i.e., the vectorization and parallelization on vector processors part, the parallelization on scalar processors part and the porting part. In this report, we describe the vectorization and parallelization on vector processors. In this vectorization and parallelization on vector processors part, the vectorization of General Tokamak Circuit Simulation Program code GTCSP, the vectorization and parallelization of Molecular Dynamics NTV (n-particle, Temperature and Velocity) Simulation code MSP2, Eddy Current Analysis code EDDYCAL, Thermal Analysis Code for Test of Passive Cooling System by HENDEL T2 code THANPACST2 and MHD Equilibrium code SELENEJ on the VPP500 are described. In the parallelization on scalar processors part, the parallelization of Monte Carlo N-Particle Transport code MCNP4B2, Plasma Hydrodynamics code using Cubic Interpolated Propagation Method PHCIP and Vectorized Monte Carlo code (continuous energy model / multi-group model) MVP/GMVP on the Paragon are described. In the porting part, the porting of Monte Carlo N-Particle Transport code MCNP4B2 and Reactor Safety Analysis code RELAP5 on the AP3000 are described. (author)

Application of model based control to robotic manipulators

Science.gov (United States)

Petrosky, Lyman J.; Oppenheim, Irving J.

1988-01-01

A robot that can duplicate humam motion capabilities in such activities as balancing, reaching, lifting, and moving has been built and tested. These capabilities are achieved through the use of real time Model-Based Control (MBC) techniques which have recently been demonstrated. MBC accounts for all manipulator inertial forces and provides stable manipulator motion control even at high speeds. To effectively demonstrate the unique capabilities of MBC, an experimental robotic manipulator was constructed, which stands upright, balancing on a two wheel base. The mathematical modeling of dynamics inherent in MBC permit the control system to perform functions that are impossible with conventional non-model based methods. These capabilities include: (1) Stable control at all speeds of operation; (2) Operations requiring dynamic stability such as balancing; (3) Detection and monitoring of applied forces without the use of load sensors; (4) Manipulator safing via detection of abnormal loads. The full potential of MBC has yet to be realized. The experiments performed for this research are only an indication of the potential applications. MBC has no inherent stability limitations and its range of applicability is limited only by the attainable sampling rate, modeling accuracy, and sensor resolution. Manipulators could be designed to operate at the highest speed mechanically attainable without being limited by control inadequacies. Manipulators capable of operating many times faster than current machines would certainly increase productivity for many tasks.

The role of crowding in parallel search: Peripheral pooling is not responsible for logarithmic efficiency in parallel search.

Science.gov (United States)

Madison, Anna; Lleras, Alejandro; Buetti, Simona

2018-02-01

Recent results from our laboratory showed that, in fixed-target parallel search tasks, reaction times increase in a logarithmic fashion with set size, and the slope of this logarithmic function is modulated by lure-target similarity. These results were interpreted as being consistent with a processing architecture where early vision (stage one) processes elements in the display in exhaustive fashion with unlimited capacity and with a limitation in resolution. Here, we evaluate the contribution of crowding to our recent logarithmic search slope findings, considering the possibility that peripheral pooling of features (as observed in crowding) may be responsible for logarithmic efficiency. Factors known to affect the strength of crowding were varied, specifically: item spacing and similarity. The results from three experiments converge on the same pattern of results: reaction times increased logarithmically with set size and were modulated by lure-target similarity even when crowding was minimized within displays through an inter-item spacing manipulation. Furthermore, we found logarithmic search efficiencies were overall improved in displays where crowding was minimized compared to displays where crowding was possible. The findings from these three experiments suggest logarithmic efficiency in efficient search is not the result peripheral pooling of features. That said, the presence of crowding does tend to reduce search efficiency, even in "pop-out" search situations.

Parallel External Memory Graph Algorithms

DEFF Research Database (Denmark)

Arge, Lars Allan; Goodrich, Michael T.; Sitchinava, Nodari

2010-01-01

In this paper, we study parallel I/O efficient graph algorithms in the Parallel External Memory (PEM) model, one o f the private-cache chip multiprocessor (CMP) models. We study the fundamental problem of list ranking which leads to efficient solutions to problems on trees, such as computing lowest...... an optimal speedup of ¿(P) in parallel I/O complexity and parallel computation time, compared to the single-processor external memory counterparts....

Dynamics three-tier hydraulic crane-manipulators

OpenAIRE

Lagerev I.A.; Lagerev A.V.

2018-01-01

The methods and generalized recommendations for modeling dynamic loading of load-bearing elements of steel structures of three-tier hydraulic cranes-manipulators are considered. Mathematical models have been developed to study the dynamics of moving elements of the crane-manipulator, the movement of the load-lifting machine on a stochastic uneven surface with a suspended load. The presented approaches can be used to calculate other types of jib cranes equipped with hydraulic drive.

Counterweight system for master-slave manipulator

International Nuclear Information System (INIS)

Haaker, L.W.; Jelatis, D.G.

1981-01-01

A counterweight system is described for use in a remote control master-slave manipulator. The manipulator consists of a rotatable horizontal support adapted to extend through the wall and two longitudinally extensible arms, a master and a slave, pivotally connected one to each end of the support. Within the support there is a means of translating linear motion to rotary motion for transfer through the barrier wall and retranslating to linear motion. (U.K.)

Evidence of market manipulation in the financial crisis

OpenAIRE

Vedant Misra; Marco Lagi; Yaneer Bar-Yam

2011-01-01

We provide direct evidence of market manipulation at the beginning of the financial crisis in November 2007. The type of manipulation, a "bear raid," would have been prevented by a regulation that was repealed by the Securities and Exchange Commission in July 2007. The regulation, the uptick rule, was designed to prevent manipulation and promote stability and was in force from 1938 as a key part of the government response to the 1929 market crash and its aftermath. On November 1, 2007, Citigr...

Manipulating Tournaments in Cup and Round Robin Competitions

OpenAIRE

Russell, Tyrel; Walsh, Toby

2009-01-01

In sports competitions, teams can manipulate the result by, for instance, throwing games. We show that we can decide how to manipulate round robin and cup competitions, two of the most popular types of sporting competitions in polynomial time. In addition, we show that finding the minimal number of games that need to be thrown to manipulate the result can also be determined in polynomial time. Finally, we show that there are several different variations of standard cup competitions where mani...

Parallel inter channel interaction mechanisms

International Nuclear Information System (INIS)

Jovic, V.; Afgan, N.; Jovic, L.

1995-01-01

Parallel channels interactions are examined. For experimental researches of nonstationary regimes flow in three parallel vertical channels results of phenomenon analysis and mechanisms of parallel channel interaction for adiabatic condition of one-phase fluid and two-phase mixture flow are shown. (author)

Parallel paving: An algorithm for generating distributed, adaptive, all-quadrilateral meshes on parallel computers

Energy Technology Data Exchange (ETDEWEB)

Lober, R.R.; Tautges, T.J.; Vaughan, C.T.

1997-03-01

Paving is an automated mesh generation algorithm which produces all-quadrilateral elements. It can additionally generate these elements in varying sizes such that the resulting mesh adapts to a function distribution, such as an error function. While powerful, conventional paving is a very serial algorithm in its operation. Parallel paving is the extension of serial paving into parallel environments to perform the same meshing functions as conventional paving only on distributed, discretized models. This extension allows large, adaptive, parallel finite element simulations to take advantage of paving`s meshing capabilities for h-remap remeshing. A significantly modified version of the CUBIT mesh generation code has been developed to host the parallel paving algorithm and demonstrate its capabilities on both two dimensional and three dimensional surface geometries and compare the resulting parallel produced meshes to conventionally paved meshes for mesh quality and algorithm performance. Sandia`s {open_quotes}tiling{close_quotes} dynamic load balancing code has also been extended to work with the paving algorithm to retain parallel efficiency as subdomains undergo iterative mesh refinement.

Development and design optimization of water hydraulic manipulator for ITER

International Nuclear Information System (INIS)

Kekaelaeinen, Teemu; Mattila, Jouni; Virvalo, Tapio

2009-01-01

This paper describes one of the research projects carried out in The Preparation of Remote Handling Engineers for ITER (PREFIT) program within the European Fusion Training Scheme (EFTS). This research project is focusing on the design and optimization of water hydraulic manipulators used to test several remote handling tasks of ITER at Divertor Test Platform 2 (DTP2), Tampere, Finland, and later in ITER. In this project, a water hydraulic manipulator designed and build by Department of Intelligent Hydraulics and Automation in Tampere University of Technology, Finland (TUT/IHA) is further optimized as a case study for a given manipulator requirement specification in order to illustrate and verify developed comprehensive design guidelines and performance metrics. Without meaningful manipulator performance parameters, the evaluation of alternative robot manipulators designs remains ad hoc at best. Therefore, more comprehensive design guidelines and performance metrics are needed for comparing and improving different existing manipulators versus task requirements or for comparing different digital prototypes at early design phase of manipulators. In this paper the description of the project, its background and developments are presented and discussed.

Design principles for six degrees-of-freedom MEMS-based precision manipulators

NARCIS (Netherlands)

Brouwer, Dannis Michel

2007-01-01

In the future, the precision manipulation of small objects will become more and more important for appliances such as data storage, micro assembly, sample manipulation in microscopes, cell manipulation, and manipulation of beam paths by micro mirrors. At the same time, there is a drive towards

Remote telerobotic replacement for master-slave manipulator

International Nuclear Information System (INIS)

Heckendorn, F.M.; Iverson, D.C.; LaValle, D.R.

1997-01-01

A remotely replaceable telerobotic manipulator (TRM) has been developed and deployed at the Defense Waste Processing Facility (DWPF) in support of its radioactive operation. The TRM replaces a Master-Slave Manipulator (MSM). The TRM is in use for both routine and recovery operations for the radioactive waste vitrification melter, the primary production device within the DWPF. The arm was designed for deployment and operation using an existing MSM penetration. This replacement of an existing MSM with a high power robotic device demonstrates the capability to perform similar replacement in other operating facilities. The MSM's were originally deployed in the DWPF to perform routine light capacity tasks. During the testing phase of the DWPF, prior to its radioactive startup in 5/96, the need to remove glass deposits that can form at the melter discharge during filling of glass containment canisters was identified. The combination of high radiation and contamination in the DWPF melter cell during radioactive operation eliminated personnel entry as a recovery option. Therefore remote cleaning methods had to be devised. The MSM's had neither the reach nor the strength required for this task. It became apparent that a robust manipulator arm would be required for recovery from these potential melter discharge pluggage events. The existing wall penetrations, used for the MSM's, could not be altered for seismic and radiological reasons. The new manipulator was required to be of considerable reach, due to existing physical layout, and strength, due to the glass removal requirement. Additionally, the device would have to compatible with high radiation and remote crane installation. The physical size of the manipulator and the weight of components must be consistent with the existing facilities. It was recognized early-on that a manipulator of sufficient strength to recover from a pluggage event would require robotic functions to constrain undesirable motions

Currency Manipulation

OpenAIRE

Weithing Zhang; Thomas Mertens; Tarek Hassan

2014-01-01

Many central banks manage the stochastic behavior of their currencies' exchange rates by imposing pegs relative to a target currency. We study the effects of such currency manipulation in a multi-country model of exchange rate determination with endogenous capital accumulation. We find that the imposition of an exchange rate peg relative to a given target currency increases the volatility of consumption in the target country and decreases the volatility of the target currency's exchange rate ...

Kinematically Optimal Robust Control of Redundant Manipulators

Science.gov (United States)

Galicki, M.

2017-12-01

This work deals with the problem of the robust optimal task space trajectory tracking subject to finite-time convergence. Kinematic and dynamic equations of a redundant manipulator are assumed to be uncertain. Moreover, globally unbounded disturbances are allowed to act on the manipulator when tracking the trajectory by the endeffector. Furthermore, the movement is to be accomplished in such a way as to minimize both the manipulator torques and their oscillations thus eliminating the potential robot vibrations. Based on suitably defined task space non-singular terminal sliding vector variable and the Lyapunov stability theory, we derive a class of chattering-free robust kinematically optimal controllers, based on the estimation of transpose Jacobian, which seem to be effective in counteracting both uncertain kinematics and dynamics, unbounded disturbances and (possible) kinematic and/or algorithmic singularities met on the robot trajectory. The numerical simulations carried out for a redundant manipulator of a SCARA type consisting of the three revolute kinematic pairs and operating in a two-dimensional task space, illustrate performance of the proposed controllers as well as comparisons with other well known control schemes.

Manipulating the Gradient

Science.gov (United States)

Gaze, Eric C.

2005-01-01

We introduce a cooperative learning, group lab for a Calculus III course to facilitate comprehension of the gradient vector and directional derivative concepts. The lab is a hands-on experience allowing students to manipulate a tangent plane and empirically measure the effect of partial derivatives on the direction of optimal ascent. (Contains 7…

Simple Ontology of Manipulation Actions based on Hand-Object Relations

DEFF Research Database (Denmark)

Wörgötter, Florentin; Aksoy, E. E.; Krüger, Norbert

2013-01-01

and time. For this we use as temporal anchor points those moments where two objects (or hand and object) touch or un-touch each other during a manipulation. We show that by this one can define a relatively small tree-like manipulation ontology. We find less than 30 fundamental manipulations. The temporal...... and encoded. Examples of manipulations recognition and execution by a robot based on this representation are given at the end of this study....

Manipulation of Cash-Settled Futures Contracts.

OpenAIRE

Pirrong, Craig

2001-01-01

Replacement of delivery settlement of futures contracts with cash settlement is frequently proposed to reduce the frequency of market manipulation. This article shows that it is always possible to design a delivery-settled futures contract that is less susceptible to cornering by a large long than any given cash-settled contract. Such a contract is more susceptible to manipulation by large shorts, however. Therefore, cash settlement does not uniformly dominate delivery settlement as a means o...

Sports Tournament Predictions Using Direct Manipulation

OpenAIRE

Vuillemot , Romain; Perin , Charles

2016-01-01

An advanced interface for sports tournament predictions uses direct manipulation to allow users to make nonlinear predictions. Unlike previous interface designs, the interface helps users focus on their prediction tasks by enabling them to first choose a winner and then fill out the rest of the bracket. In real-world tests of the proposed interface (for the 2014 FIFA World Cup tournament and 2015/2016 UEFA Champions League), the authors validated the use of direct manipulation as an alternati...

HUMAN NATURE: BETWEEN PERSUASION AND MANIPULATION

Directory of Open Access Journals (Sweden)

CRISTINA LUCIA ȘUTIU

2014-11-01

Full Text Available Each word is an attempt to influence other persons, as Alex Mucchielli said. Communication, by using words, is a characteristic of human beings, and it plays an important role in everyday life. Communication can be seen as an attempt to share information through a process of symbolic interaction between human beings. It is an essential life process through which humans create, transmit and utilize information by words. Putting words in act, we can express feelings, we can share opinions and we can obtain whatever we want, finally. It is essential to take into account certain ethical rules whenever we start a communication process. As the main purpose of communication is to convince people, this goal can be achieved only by using persuasion and/or manipulation. The last century is a sort of witness as regards the use of words in order to persuade people to adhere to certain ideological precepts and to determine them to act in a certain desirable way by the initiators of the communication process. Practically, there is a fine line between persuasion and manipulation; and in this situation, it is hard for ordinary people to distinguish between them. Manipulation appears like a persuasive process and it hides its true aims. This is the only way by which it can operate and for that it is considered immoral and invasive in the mind and soul of people. Human beings are now in the position to look for a way to protect themselves against such an invasive act and to find a way to distinguish between correct and false information. What can we do? In this study we analyze persuasion and manipulation from an ethical point of view and we search for paths to protect ourselves from the manipulative techniques.

Manipulator Comparative Testing Program: Final report

International Nuclear Information System (INIS)

Draper, J.V.; Handel, S.J.; Sundstrom, E.; Herndon, J.N; Fujita, Y.; Maeda, M.

1987-02-01

The manipulator systems tested included the Meidensha BILARM 83A, the Central Research Laboratories Model M-2, and the GCA PaR Systems Model 6000. Six manipulator and control mode combinations were evaluated: (1) the BILARM in master/slave mode without force reflection, (2) the BILARM in master/slave mode with force reflection, (3) the Model M-2 in master/slave mode without force reflection, (4) the Model M-2 in master/slave mode with force reflection, (5) the BILARM with switchbox controls, and (6) the PaR 6000 with switchbox controls. The experiments examined differences between master/slave systems with and without force reflection and differences between master/slave systems and switchbox-controlled systems. A fourth experiment examined the relative contributions of the remote viewing system and the manipulator system to the performance of remote handling tasks. Results of the experiments showed that operators using the Model M-2 in master/slave mode had significantly faster times to completion than operators using the BILARM in master/slave mode, with about the same error rate per trial. Operators were slower using the BILARM with force reflection than without it, and they committed more errors. There was no statistically significant difference between force-reflection and nonforce-reflection conditions for the M-2 manipulator for any of the performance criteria. Tasks and procedures used in this testing were not sensitive to differences within any single system. No inferences about the effect of force reflection on remote task performance should be made from these data. The two manipulator systems in switchbox mode had significantly slower times to completion than any system in master/slave mode, with approximately the same error rate per trial. There were no significant differences between the BILARM in switchbox mode and the PaR arm

Seeing or moving in parallel

DEFF Research Database (Denmark)

Christensen, Mark Schram; Ehrsson, H Henrik; Nielsen, Jens Bo

2013-01-01

a different network, involving bilateral dorsal premotor cortex (PMd), primary motor cortex, and SMA, was more active when subjects viewed parallel movements while performing either symmetrical or parallel movements. Correlations between behavioral instability and brain activity were present in right lateral...... adduction-abduction movements symmetrically or in parallel with real-time congruent or incongruent visual feedback of the movements. One network, consisting of bilateral superior and middle frontal gyrus and supplementary motor area (SMA), was more active when subjects performed parallel movements, whereas...

Exploiting variability for energy optimization of parallel programs

Energy Technology Data Exchange (ETDEWEB)

Lavrijsen, Wim [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Iancu, Costin [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); de Jong, Wibe [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chen, Xin [Georgia Inst. of Technology, Atlanta, GA (United States); Schwan, Karsten [Georgia Inst. of Technology, Atlanta, GA (United States)

2016-04-18

Here in this paper we present optimizations that use DVFS mechanisms to reduce the total energy usage in scientific applications. Our main insight is that noise is intrinsic to large scale parallel executions and it appears whenever shared resources are contended. The presence of noise allows us to identify and manipulate any program regions amenable to DVFS. When compared to previous energy optimizations that make per core decisions using predictions of the running time, our scheme uses a qualitative approach to recognize the signature of executions amenable to DVFS. By recognizing the "shape of variability" we can optimize codes with highly dynamic behavior, which pose challenges to all existing DVFS techniques. We validate our approach using offline and online analyses for one-sided and two-sided communication paradigms. We have applied our methods to NWChem, and we show best case improvements in energy use of 12% at no loss in performance when using online optimizations running on 720 Haswell cores with one-sided communication. With NWChem on MPI two-sided and offline analysis, capturing the initialization, we find energy savings of up to 20%, with less than 1% performance cost.

The numerical parallel computing of photon transport

International Nuclear Information System (INIS)

Huang Qingnan; Liang Xiaoguang; Zhang Lifa

1998-12-01

The parallel computing of photon transport is investigated, the parallel algorithm and the parallelization of programs on parallel computers both with shared memory and with distributed memory are discussed. By analyzing the inherent law of the mathematics and physics model of photon transport according to the structure feature of parallel computers, using the strategy of 'to divide and conquer', adjusting the algorithm structure of the program, dissolving the data relationship, finding parallel liable ingredients and creating large grain parallel subtasks, the sequential computing of photon transport into is efficiently transformed into parallel and vector computing. The program was run on various HP parallel computers such as the HY-1 (PVP), the Challenge (SMP) and the YH-3 (MPP) and very good parallel speedup has been gotten

Hypergraph partitioning implementation for parallelizing matrix-vector multiplication using CUDA GPU-based parallel computing

Science.gov (United States)

Murni, Bustamam, A.; Ernastuti, Handhika, T.; Kerami, D.

2017-07-01

Calculation of the matrix-vector multiplication in the real-world problems often involves large matrix with arbitrary size. Therefore, parallelization is needed to speed up the calculation process that usually takes a long time. Graph partitioning techniques that have been discussed in the previous studies cannot be used to complete the parallelized calculation of matrix-vector multiplication with arbitrary size. This is due to the assumption of graph partitioning techniques that can only solve the square and symmetric matrix. Hypergraph partitioning techniques will overcome the shortcomings of the graph partitioning technique. This paper addresses the efficient parallelization of matrix-vector multiplication through hypergraph partitioning techniques using CUDA GPU-based parallel computing. CUDA (compute unified device architecture) is a parallel computing platform and programming model that was created by NVIDIA and implemented by the GPU (graphics processing unit).

Writing parallel programs that work

CERN Multimedia

CERN. Geneva

2012-01-01

Serial algorithms typically run inefficiently on parallel machines. This may sound like an obvious statement, but it is the root cause of why parallel programming is considered to be difficult. The current state of the computer industry is still that almost all programs in existence are serial. This talk will describe the techniques used in the Intel Parallel Studio to provide a developer with the tools necessary to understand the behaviors and limitations of the existing serial programs. Once the limitations are known the developer can refactor the algorithms and reanalyze the resulting programs with the tools in the Intel Parallel Studio to create parallel programs that work. About the speaker Paul Petersen is a Sr. Principal Engineer in the Software and Solutions Group (SSG) at Intel. He received a Ph.D. degree in Computer Science from the University of Illinois in 1993. After UIUC, he was employed at Kuck and Associates, Inc. (KAI) working on auto-parallelizing compiler (KAP), and was involved in th...

Parallel Framework for Cooperative Processes

Directory of Open Access Journals (Sweden)

Mitică Craus

2005-01-01

Full Text Available This paper describes the work of an object oriented framework designed to be used in the parallelization of a set of related algorithms. The idea behind the system we are describing is to have a re-usable framework for running several sequential algorithms in a parallel environment. The algorithms that the framework can be used with have several things in common: they have to run in cycles and the work should be possible to be split between several "processing units". The parallel framework uses the message-passing communication paradigm and is organized as a master-slave system. Two applications are presented: an Ant Colony Optimization (ACO parallel algorithm for the Travelling Salesman Problem (TSP and an Image Processing (IP parallel algorithm for the Symmetrical Neighborhood Filter (SNF. The implementations of these applications by means of the parallel framework prove to have good performances: approximatively linear speedup and low communication cost.

Compiler Technology for Parallel Scientific Computation

Directory of Open Access Journals (Sweden)

Can Özturan

1994-01-01

Full Text Available There is a need for compiler technology that, given the source program, will generate efficient parallel codes for different architectures with minimal user involvement. Parallel computation is becoming indispensable in solving large-scale problems in science and engineering. Yet, the use of parallel computation is limited by the high costs of developing the needed software. To overcome this difficulty we advocate a comprehensive approach to the development of scalable architecture-independent software for scientific computation based on our experience with equational programming language (EPL. Our approach is based on a program decomposition, parallel code synthesis, and run-time support for parallel scientific computation. The program decomposition is guided by the source program annotations provided by the user. The synthesis of parallel code is based on configurations that describe the overall computation as a set of interacting components. Run-time support is provided by the compiler-generated code that redistributes computation and data during object program execution. The generated parallel code is optimized using techniques of data alignment, operator placement, wavefront determination, and memory optimization. In this article we discuss annotations, configurations, parallel code generation, and run-time support suitable for parallel programs written in the functional parallel programming language EPL and in Fortran.

Acoustic Devices for Particle and Cell Manipulation and Sensing

Directory of Open Access Journals (Sweden)

Yongqiang Qiu

2014-08-01

Full Text Available An emerging demand for the precise manipulation of cells and particles for applications in cell biology and analytical chemistry has driven rapid development of ultrasonic manipulation technology. Compared to the other manipulation technologies, such as magnetic tweezing, dielectrophoresis and optical tweezing, ultrasonic manipulation has shown potential in a variety of applications, with its advantages of versatile, inexpensive and easy integration into microfluidic systems, maintenance of cell viability, and generation of sufficient forces to handle particles, cells and their agglomerates. This article briefly reviews current practice and reports our development of various ultrasonic standing wave manipulation devices, including simple devices integrated with high frequency (>20 MHz ultrasonic transducers for the investigation of biological cells and complex ultrasonic transducer array systems to explore the feasibility of electronically controlled 2-D and 3-D manipulation. Piezoelectric and passive materials, fabrication techniques, characterization methods and possible applications are discussed. The behavior and performance of the devices have been investigated and predicted with computer simulations, and verified experimentally. Issues met during development are highlighted and discussed. To assist long term practical adoption, approaches to low-cost, wafer level batch-production and commercialization potential are also addressed.

Remote manipulation techniques in the maintenance and repair of nuclear power plants

International Nuclear Information System (INIS)

Rininsland, H.; Boehme, G.

1986-01-01

Remote manipulation means the application of multi-purpose devices featuring high mobility and universal applicability. The paper describes such a remote manipulation system (manipulation vehicle MF1 and MF2, master-slave manipulator, TFTR maintenance manipulator) which can be used flexibly in the NNP during maintenance and repair and in incident and accident situations. Connecting elements and tools can be redesigned for remote manipulation to meet the specific application environments. (DG) [de

A motion sensing-based framework for robotic manipulation.

Science.gov (United States)

Deng, Hao; Xia, Zeyang; Weng, Shaokui; Gan, Yangzhou; Fang, Peng; Xiong, Jing

2016-01-01

To data, outside of the controlled environments, robots normally perform manipulation tasks operating with human. This pattern requires the robot operators with high technical skills training for varied teach-pendant operating system. Motion sensing technology, which enables human-machine interaction in a novel and natural interface using gestures, has crucially inspired us to adopt this user-friendly and straightforward operation mode on robotic manipulation. Thus, in this paper, we presented a motion sensing-based framework for robotic manipulation, which recognizes gesture commands captured from motion sensing input device and drives the action of robots. For compatibility, a general hardware interface layer was also developed in the framework. Simulation and physical experiments have been conducted for preliminary validation. The results have shown that the proposed framework is an effective approach for general robotic manipulation with motion sensing control.

Intelligent Switching Control of Pneumatic Artificial Muscle Manipulator

Science.gov (United States)

Ahn, Kyoung Kwan; Thanh, Tu Diep Cong; Ahn, Young Kong

Problems with the control, oscillatory motion and compliance of pneumatic systems have prevented their widespread use in advanced robotics. However, their compactness, power/weight ratio, ease of maintenance and inherent safety are the factors that could potentially be exploited in sophisticated dexterous manipulator designs. These advantages have led to the development of novel actuators such as the McKibben Muscle, Rubber Actuator and Pneumatic Artificial Muscle Manipulators. However, some limitations still exist, such as deterioration of the performance of transient response due to the change of the external inertia load in the pneumatic artificial muscle manipulator. To overcome this problem, switching algorithm of control parameter using learning vector quantization neural network (LVQNN) is newly proposed, which estimates the external inertia load of the pneumatic artificial muscle manipulator. The effectiveness of the proposed control algorithm is demonstrated through experiments with different external inertia loads.

Predictors of Host Specificity among Behavior-Manipulating Parasites

DEFF Research Database (Denmark)

Fredensborg, B. L.

2014-01-01

specifically, hosts’ behavioral modification that involves interaction with the central nervous system presumably restricts parasites to more closely related hosts than does manipulation of the host’s behavior via debilitation of the host’s physiology. The results of the analysis suggest that phylogenetic......-specialist that has a restricted ecological niche that it masters. Parasites that manipulate hosts’ behavior are often thought to represent resource-specialists based on a few spectacular examples of manipulation of the host’s behavior. However, the determinants of which, and how many, hosts a manipulating parasite...... of parasites and hosts. Using individual and multivariate analyses, I examined the effect of the host’s and parasite’s taxonomy, location of the parasite in the host, type of behavioral change, and the effect of debilitation on host-specificity, measured as the mean taxonomic relatedness of hosts...

Parallel computing: numerics, applications, and trends

National Research Council Canada - National Science Library

Trobec, Roman; Vajteršic, Marián; Zinterhof, Peter

2009-01-01

... and/or distributed systems. The contributions to this book are focused on topics most concerned in the trends of today's parallel computing. These range from parallel algorithmics, programming, tools, network computing to future parallel computing. Particular attention is paid to parallel numerics: linear algebra, differential equations, numerica...

Parallel Computing Strategies for Irregular Algorithms

Science.gov (United States)

Biswas, Rupak; Oliker, Leonid; Shan, Hongzhang; Biegel, Bryan (Technical Monitor)

2002-01-01

Parallel computing promises several orders of magnitude increase in our ability to solve realistic computationally-intensive problems, but relies on their efficient mapping and execution on large-scale multiprocessor architectures. Unfortunately, many important applications are irregular and dynamic in nature, making their effective parallel implementation a daunting task. Moreover, with the proliferation of parallel architectures and programming paradigms, the typical scientist is faced with a plethora of questions that must be answered in order to obtain an acceptable parallel implementation of the solution algorithm. In this paper, we consider three representative irregular applications: unstructured remeshing, sparse matrix computations, and N-body problems, and parallelize them using various popular programming paradigms on a wide spectrum of computer platforms ranging from state-of-the-art supercomputers to PC clusters. We present the underlying problems, the solution algorithms, and the parallel implementation strategies. Smart load-balancing, partitioning, and ordering techniques are used to enhance parallel performance. Overall results demonstrate the complexity of efficiently parallelizing irregular algorithms.

Manipulation of single neutral atoms in optical lattices

International Nuclear Information System (INIS)

Zhang Chuanwei; Das Sarma, S.; Rolston, S. L.

2006-01-01

We analyze a scheme to manipulate quantum states of neutral atoms at individual sites of optical lattices using focused laser beams. Spatial distributions of focused laser intensities induce position-dependent energy shifts of hyperfine states, which, combined with microwave radiation, allow selective manipulation of quantum states of individual target atoms. We show that various errors in the manipulation process are suppressed below 10 -4 with properly chosen microwave pulse sequences and laser parameters. A similar idea is also applied to measure quantum states of single atoms in optical lattices

The Glasgow Parallel Reduction Machine: Programming Shared-memory Many-core Systems using Parallel Task Composition

Directory of Open Access Journals (Sweden)

Ashkan Tousimojarad

2013-12-01

Full Text Available We present the Glasgow Parallel Reduction Machine (GPRM, a novel, flexible framework for parallel task-composition based many-core programming. We allow the programmer to structure programs into task code, written as C++ classes, and communication code, written in a restricted subset of C++ with functional semantics and parallel evaluation. In this paper we discuss the GPRM, the virtual machine framework that enables the parallel task composition approach. We focus the discussion on GPIR, the functional language used as the intermediate representation of the bytecode running on the GPRM. Using examples in this language we show the flexibility and power of our task composition framework. We demonstrate the potential using an implementation of a merge sort algorithm on a 64-core Tilera processor, as well as on a conventional Intel quad-core processor and an AMD 48-core processor system. We also compare our framework with OpenMP tasks in a parallel pointer chasing algorithm running on the Tilera processor. Our results show that the GPRM programs outperform the corresponding OpenMP codes on all test platforms, and can greatly facilitate writing of parallel programs, in particular non-data parallel algorithms such as reductions.

Parallel Evolution of Sperm Hyper-Activation Ca2+ Channels.

Science.gov (United States)

Cooper, Jacob C; Phadnis, Nitin

2017-07-01

Sperm hyper-activation is a dramatic change in sperm behavior where mature sperm burst into a final sprint in the race to the egg. The mechanism of sperm hyper-activation in many metazoans, including humans, consists of a jolt of Ca2+ into the sperm flagellum via CatSper ion channels. Surprisingly, all nine CatSper genes have been independently lost in several animal lineages. In Drosophila, sperm hyper-activation is performed through the cooption of the polycystic kidney disease 2 (pkd2) Ca2+ channel. The parallels between CatSpers in primates and pkd2 in Drosophila provide a unique opportunity to examine the molecular evolution of the sperm hyper-activation machinery in two independent, nonhomologous calcium channels separated by > 500 million years of divergence. Here, we use a comprehensive phylogenomic approach to investigate the selective pressures on these sperm hyper-activation channels. First, we find that the entire CatSper complex evolves rapidly under recurrent positive selection in primates. Second, we find that pkd2 has parallel patterns of adaptive evolution in Drosophila. Third, we show that this adaptive evolution of pkd2 is driven by its role in sperm hyper-activation. These patterns of selection suggest that the evolution of the sperm hyper-activation machinery is driven by sexual conflict with antagonistic ligands that modulate channel activity. Together, our results add sperm hyper-activation channels to the class of fast evolving reproductive proteins and provide insights into the mechanisms used by the sexes to manipulate sperm behavior. © The Author 2017. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

Streaming for Functional Data-Parallel Languages

DEFF Research Database (Denmark)

Madsen, Frederik Meisner

In this thesis, we investigate streaming as a general solution to the space inefficiency commonly found in functional data-parallel programming languages. The data-parallel paradigm maps well to parallel SIMD-style hardware. However, the traditional fully materializing execution strategy...... by extending two existing data-parallel languages: NESL and Accelerate. In the extensions we map bulk operations to data-parallel streams that can evaluate fully sequential, fully parallel or anything in between. By a dataflow, piecewise parallel execution strategy, the runtime system can adjust to any target...... flattening necessitates all sub-computations to materialize at the same time. For example, naive n by n matrix multiplication requires n^3 space in NESL because the algorithm contains n^3 independent scalar multiplications. For large values of n, this is completely unacceptable. We address the problem...

Master-slave type manipulator

International Nuclear Information System (INIS)

Haaker, L.W.; Jelatis, D.G.

1979-01-01

Remote control manipulator of the master-slave type for carrying out work on the other side of a shield wall. This appliance allows a Y movement relative displacement, the function of which is to extend the range of the manipulator towards the front and also to facilitate its installation, the lateral rotation or inclination of the slave arm in relation to the master arm, and the Z movement extension through which the length of the slave arm is increased in comparison with that of the master arm. Devices have been developed which transform the linear movements into rotational movements to enable these movements to be transmitted through rotational seal fittings capable of ensuring the safety of the separation between the operator's environment and that in the work area. Particular improvements have been made to the handles, handle seals, pincer mechanisms, etc [fr

Do Managers Manipulate Earnings Prior to Management Buyouts?

NARCIS (Netherlands)

Mao, Y.; Renneboog, L.D.R.

2013-01-01

Abstract: To address the question as to whether managers manipulate accounting numbers downwards prior to management buyouts (MBOs), we implement an industry-adjusted buyout-specific approach and receive an affirmative answer. In UK buyout companies, negative earnings manipulation (understating the

Adaptive hidden Markov model with anomaly States for price manipulation detection.

Science.gov (United States)

Cao, Yi; Li, Yuhua; Coleman, Sonya; Belatreche, Ammar; McGinnity, Thomas Martin

2015-02-01

Price manipulation refers to the activities of those traders who use carefully designed trading behaviors to manually push up or down the underlying equity prices for making profits. With increasing volumes and frequency of trading, price manipulation can be extremely damaging to the proper functioning and integrity of capital markets. The existing literature focuses on either empirical studies of market abuse cases or analysis of particular manipulation types based on certain assumptions. Effective approaches for analyzing and detecting price manipulation in real time are yet to be developed. This paper proposes a novel approach, called adaptive hidden Markov model with anomaly states (AHMMAS) for modeling and detecting price manipulation activities. Together with wavelet transformations and gradients as the feature extraction methods, the AHMMAS model caters to price manipulation detection and basic manipulation type recognition. The evaluation experiments conducted on seven stock tick data from NASDAQ and the London Stock Exchange and 10 simulated stock prices by stochastic differential equation show that the proposed AHMMAS model can effectively detect price manipulation patterns and outperforms the selected benchmark models.

Development of a Control System for PRIDE Remote Servo-manipulator

International Nuclear Information System (INIS)

Lee, Jong Kwang; Park, Byung Suk; Lee, Hyo Jik; Kim, Kyung Tae; Kim, Sung Hyun; Park, Hee Sung; Kim, Young Hwan; Jung, Jae Hoo; Kim, Ki Ho; Kim, Ho Dong

2009-12-01

KAERI is developing the PRIDE(PyRoprocess Integrated inactive DEmonstration) facility to verify the integrated performance of full Pyroprocess flow. A main process cell in the PRIDE facility will be filled with argon gas which prohibits direct access by human operators. Therefore, all the operation and maintenance of the process equipment is performed remotely through a master-slave manipulation. This research focuses on the design, fabrication, and interface of a control system which integrates several hardware systems such as a dual arm master-slave servo-manipulator, a horizontally moving transporter for a master manipulator, a bridge transporter for a slave manipulator, a chain hoist, camera systems and their display system, a manual console, and a pendant, etc. Also, a bilateral force-reflection controller considering an elasticity and vibration modes of wire cable has been developed for master-slave remote manipulation. The results obtained in this study will be applied for the force-reflection control of the bridge-transported master-slave servo-manipulator system for use in the PRIDE facility. Since this research is an essential work in robotics related fields, the results would be widely used for developing power manipulators and process automation equipment

Development of a Control System for PRIDE Remote Servo-manipulator

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Kwang; Park, Byung Suk; Lee, Hyo Jik; Kim, Kyung Tae; Kim, Sung Hyun; Park, Hee Sung; Kim, Young Hwan; Jung, Jae Hoo; Kim, Ki Ho; Kim, Ho Dong

2009-12-15

KAERI is developing the PRIDE(PyRoprocess Integrated inactive DEmonstration) facility to verify the integrated performance of full Pyroprocess flow. A main process cell in the PRIDE facility will be filled with argon gas which prohibits direct access by human operators. Therefore, all the operation and maintenance of the process equipment is performed remotely through a master-slave manipulation. This research focuses on the design, fabrication, and interface of a control system which integrates several hardware systems such as a dual arm master-slave servo-manipulator, a horizontally moving transporter for a master manipulator, a bridge transporter for a slave manipulator, a chain hoist, camera systems and their display system, a manual console, and a pendant, etc. Also, a bilateral force-reflection controller considering an elasticity and vibration modes of wire cable has been developed for master-slave remote manipulation. The results obtained in this study will be applied for the force-reflection control of the bridge-transported master-slave servo-manipulator system for use in the PRIDE facility. Since this research is an essential work in robotics related fields, the results would be widely used for developing power manipulators and process automation equipment.

Patterns for Parallel Software Design

CERN Document Server

Ortega-Arjona, Jorge Luis

2010-01-01

Essential reading to understand patterns for parallel programming Software patterns have revolutionized the way we think about how software is designed, built, and documented, and the design of parallel software requires you to consider other particular design aspects and special skills. From clusters to supercomputers, success heavily depends on the design skills of software developers. Patterns for Parallel Software Design presents a pattern-oriented software architecture approach to parallel software design. This approach is not a design method in the classic sense, but a new way of managin

High performance parallel I/O

CERN Document Server

Prabhat

2014-01-01

Gain Critical Insight into the Parallel I/O EcosystemParallel I/O is an integral component of modern high performance computing (HPC), especially in storing and processing very large datasets to facilitate scientific discovery. Revealing the state of the art in this field, High Performance Parallel I/O draws on insights from leading practitioners, researchers, software architects, developers, and scientists who shed light on the parallel I/O ecosystem.The first part of the book explains how large-scale HPC facilities scope, configure, and operate systems, with an emphasis on choices of I/O har