WorldWideScience

Sample records for optimal boarding method

  1. Optimal boarding method for airline passengers

    Energy Technology Data Exchange (ETDEWEB)

    Steffen, Jason H.; /Fermilab

    2008-02-01

    Using a Markov Chain Monte Carlo optimization algorithm and a computer simulation, I find the passenger ordering which minimizes the time required to board the passengers onto an airplane. The model that I employ assumes that the time that a passenger requires to load his or her luggage is the dominant contribution to the time needed to completely fill the aircraft. The optimal boarding strategy may reduce the time required to board and airplane by over a factor of four and possibly more depending upon the dimensions of the aircraft. I explore some features of the optimal boarding method and discuss practical modifications to the optimal. Finally, I mention some of the benefits that could come from implementing an improved passenger boarding scheme.

  2. Experimental test of airplane boarding methods

    CERN Document Server

    Steffen, Jason H

    2011-01-01

    We report the results of an experimental comparison of different airplane boarding methods. This test was conducted in a mock 757 fuselage, located on a Southern California soundstage, with 12 rows of six seats and a single aisle. Five methods were tested using 72 passengers of various ages. We found a significant reduction in the boarding times of optimized methods over traditional methods. These improved methods, if properly implemented, could result in a significant savings to airline companies.

  3. Optimization Of Assembly Line Of Printed Circuit Board Using Simulation

    Directory of Open Access Journals (Sweden)

    Kamal Alzameli

    2015-08-01

    Full Text Available The development of an assembly line would not stop at a specific research even if that research contains very detailed sectors of one assembly line or starting from customer order to product delivery. Therefore continuous improvement needs to be vigorous for continuous productivity improvement and innovation. The optimization process of printed circuit board assembly line includes hard and soft optimization. The hard optimization includes hardware changes via design and the soft optimization is figured via simulation of the current assembly line and analysis. The aim of the research is to determine the bottlenecks find a solution and develop improvement method via changing the configuration of the setup on the assembly line until the feasible optimal configuration is definite. The software that will be used for this simulation is Arena software. The data of the research is collected from real assembly line. The best engineering assumption for the area is used for no permanent data that could be available such as the data that might be collected from the manual stations. In addition to the aim of the research is to get a better yield via improving the time of the PCB assembly process. Hence the outcome to all of these attempts of optimizing the assembly line of PCB for continuous improvement is to deliver good quality products reduce cost and minimize the time to delivery and meet the customer expectations.

  4. Combining the genetic algorithms with artificial neural networks for optimization of board allocating

    Institute of Scientific and Technical Information of China (English)

    CAOJun; ZHANGYi-zhuo; YUEQi

    2003-01-01

    This paper introduced the Genetic Algorithms (GAs) and Artificial Neural Networks(ANNs),which have been widely used in optimization of allocating.The combinationg way of the two optimizing algorithms was used in board allocating of fumiture production.In the experiment,the rectangular flake board of 3650mm×1850mm was used as raw material to allocate 100 sets of Table Bucked.The utilizing rate of the board reached 94.14% and the calculating time was only 35s.The experiment result proofed that the method by using the GA for optimizing the weights of the ANN can raise the utilizing rate of the board and can shorten the time of the design.At the same time,this method can simultaneously searched in many directions,thus greatly increasing the probability of finding a global optimum.

  5. Search for the optimal size of printed circuit boards for mechanical structures for electronic equipment

    Directory of Open Access Journals (Sweden)

    Yefimenko A. A.

    2014-12-01

    Full Text Available The authors present a method, an algorithm and a program, designed to determine the optimal size of printed circuit boards (PCB of mechanical structures and different kinds of electronic equipment. The PCB filling factor is taken as an optimization criterion. The method allows one to quickly determine the dependence of the filling factor on the size of the PCB for various components.

  6. Stochastic optimization methods

    CERN Document Server

    Marti, Kurt

    2005-01-01

    Optimization problems arising in practice involve random parameters. For the computation of robust optimal solutions, i.e., optimal solutions being insensitive with respect to random parameter variations, deterministic substitute problems are needed. Based on the distribution of the random data, and using decision theoretical concepts, optimization problems under stochastic uncertainty are converted into deterministic substitute problems. Due to the occurring probabilities and expectations, approximative solution techniques must be applied. Deterministic and stochastic approximation methods and their analytical properties are provided: Taylor expansion, regression and response surface methods, probability inequalities, First Order Reliability Methods, convex approximation/deterministic descent directions/efficient points, stochastic approximation methods, differentiation of probability and mean value functions. Convergence results of the resulting iterative solution procedures are given.

  7. Practical methods of optimization

    CERN Document Server

    Fletcher, R

    2013-01-01

    Fully describes optimization methods that are currently most valuable in solving real-life problems. Since optimization has applications in almost every branch of science and technology, the text emphasizes their practical aspects in conjunction with the heuristics useful in making them perform more reliably and efficiently. To this end, it presents comparative numerical studies to give readers a feel for possibile applications and to illustrate the problems in assessing evidence. Also provides theoretical background which provides insights into how methods are derived. This edition offers rev

  8. Application of Hybrid Optimization-Expert System for Optimal Power Management on Board Space Power Station

    Science.gov (United States)

    Momoh, James; Chattopadhyay, Deb; Basheer, Omar Ali AL

    1996-01-01

    The space power system has two sources of energy: photo-voltaic blankets and batteries. The optimal power management problem on-board has two broad operations: off-line power scheduling to determine the load allocation schedule of the next several hours based on the forecast of load and solar power availability. The nature of this study puts less emphasis on speed requirement for computation and more importance on the optimality of the solution. The second category problem, on-line power rescheduling, is needed in the event of occurrence of a contingency to optimally reschedule the loads to minimize the 'unused' or 'wasted' energy while keeping the priority on certain type of load and minimum disturbance of the original optimal schedule determined in the first-stage off-line study. The computational performance of the on-line 'rescheduler' is an important criterion and plays a critical role in the selection of the appropriate tool. The Howard University Center for Energy Systems and Control has developed a hybrid optimization-expert systems based power management program. The pre-scheduler has been developed using a non-linear multi-objective optimization technique called the Outer Approximation method and implemented using the General Algebraic Modeling System (GAMS). The optimization model has the capability of dealing with multiple conflicting objectives viz. maximizing energy utilization, minimizing the variation of load over a day, etc. and incorporates several complex interaction between the loads in a space system. The rescheduling is performed using an expert system developed in PROLOG which utilizes a rule-base for reallocation of the loads in an emergency condition viz. shortage of power due to solar array failure, increase of base load, addition of new activity, repetition of old activity etc. Both the modules handle decision making on battery charging and discharging and allocation of loads over a time-horizon of a day divided into intervals of 10

  9. Q board interviews: An effective method to research user opinions

    NARCIS (Netherlands)

    Wiegers, T.; De Lange, C.J.M.; Vergeest, J.S.M.

    2014-01-01

    Q board interviews can be applied as an effective method to get insight in the opinions of participants. Q board interviews form the interviewing part of Q methodology. Q methodology can be used to identify typical sets of opinions. However, in many studies, the research goal is to order opinions an

  10. Q board interviews: An effective method to research user opinions

    NARCIS (Netherlands)

    Wiegers, T.; De Lange, C.J.M.; Vergeest, J.S.M.

    2014-01-01

    Q board interviews can be applied as an effective method to get insight in the opinions of participants. Q board interviews form the interviewing part of Q methodology. Q methodology can be used to identify typical sets of opinions. However, in many studies, the research goal is to order opinions

  11. Homotopy optimization methods for global optimization.

    Energy Technology Data Exchange (ETDEWEB)

    Dunlavy, Daniel M.; O' Leary, Dianne P. (University of Maryland, College Park, MD)

    2005-12-01

    We define a new method for global optimization, the Homotopy Optimization Method (HOM). This method differs from previous homotopy and continuation methods in that its aim is to find a minimizer for each of a set of values of the homotopy parameter, rather than to follow a path of minimizers. We define a second method, called HOPE, by allowing HOM to follow an ensemble of points obtained by perturbation of previous ones. We relate this new method to standard methods such as simulated annealing and show under what circumstances it is superior. We present results of extensive numerical experiments demonstrating performance of HOM and HOPE.

  12. Social Learning Methods in Board Games

    CERN Document Server

    Marivate, Vukosi N

    2008-01-01

    This paper discusses the effects of social learning in training of game playing agents. The training of agents in a social context instead of a self-play environment is investigated. Agents that use the reinforcement learning algorithms are trained in social settings. This mimics the way in which players of board games such as scrabble and chess mentor each other in their clubs. A Round Robin tournament and a modified Swiss tournament setting are used for the training. The agents trained using social settings are compared to self play agents and results indicate that more robust agents emerge from the social training setting. Higher state space games can benefit from such settings as diverse set of agents will have multiple strategies that increase the chances of obtaining more experienced players at the end of training. The Social Learning trained agents exhibit better playing experience than self play agents. The modified Swiss playing style spawns a larger number of better playing agents as the population ...

  13. Stochastic optimization methods

    CERN Document Server

    Marti, Kurt

    2008-01-01

    Optimization problems arising in practice involve random model parameters. This book features many illustrations, several examples, and applications to concrete problems from engineering and operations research.

  14. Optimization methods applied to hybrid vehicle design

    Science.gov (United States)

    Donoghue, J. F.; Burghart, J. H.

    1983-01-01

    The use of optimization methods as an effective design tool in the design of hybrid vehicle propulsion systems is demonstrated. Optimization techniques were used to select values for three design parameters (battery weight, heat engine power rating and power split between the two on-board energy sources) such that various measures of vehicle performance (acquisition cost, life cycle cost and petroleum consumption) were optimized. The apporach produced designs which were often significant improvements over hybrid designs already reported on in the literature. The principal conclusions are as follows. First, it was found that the strategy used to split the required power between the two on-board energy sources can have a significant effect on life cycle cost and petroleum consumption. Second, the optimization program should be constructed so that performance measures and design variables can be easily changed. Third, the vehicle simulation program has a significant effect on the computer run time of the overall optimization program; run time can be significantly reduced by proper design of the types of trips the vehicle takes in a one year period. Fourth, care must be taken in designing the cost and constraint expressions which are used in the optimization so that they are relatively smooth functions of the design variables. Fifth, proper handling of constraints on battery weight and heat engine rating, variables which must be large enough to meet power demands, is particularly important for the success of an optimization study. Finally, the principal conclusion is that optimization methods provide a practical tool for carrying out the design of a hybrid vehicle propulsion system.

  15. Analytical methods of optimization

    CERN Document Server

    Lawden, D F

    2006-01-01

    Suitable for advanced undergraduates and graduate students, this text surveys the classical theory of the calculus of variations. It takes the approach most appropriate for applications to problems of optimizing the behavior of engineering systems. Two of these problem areas have strongly influenced this presentation: the design of the control systems and the choice of rocket trajectories to be followed by terrestrial and extraterrestrial vehicles.Topics include static systems, control systems, additional constraints, the Hamilton-Jacobi equation, and the accessory optimization problem. Prereq

  16. Making board meetings work: the Doyle/Straus interaction method.

    Science.gov (United States)

    Straus, D; Doyle, M

    1978-01-01

    The Doyle/Straus Interaction Method is just now beginning to be used at corporate board meetings on the West Coast. The methodology, based on ten years of experimentation with problem-solving and decisionmaking groups of all kinds, seems to hold a host of benefits not only for meetings at board level but for committee meetings of all kinds. Their step-by-step analysis of the problems that are caused by people and space promises much for the corporations that want to move the directorate into the 20th Century or even the 21st!

  17. Optimizing Methods in Simulation

    Science.gov (United States)

    1981-08-01

    exploited by Kiefer and Wolfowitz -; (1959). Wald (1943) used the criterion of D-optimality - in some other context and was so named by Kiefer and...of discrepency between the observed and expected value A is obtained in terms of mean squared errors ( MSE ). i Consider the model, E(Ylx) = a + ex and...V(YIX) = 0 2 Let L < x < U, be the interval of possible x values. The MSE (x) is the mean squared error of x as obtained from y. Let w(x) be a weight

  18. Optimization methods for logical inference

    CERN Document Server

    Chandru, Vijay

    2011-01-01

    Merging logic and mathematics in deductive inference-an innovative, cutting-edge approach. Optimization methods for logical inference? Absolutely, say Vijay Chandru and John Hooker, two major contributors to this rapidly expanding field. And even though ""solving logical inference problems with optimization methods may seem a bit like eating sauerkraut with chopsticks. . . it is the mathematical structure of a problem that determines whether an optimization model can help solve it, not the context in which the problem occurs."" Presenting powerful, proven optimization techniques for logic in

  19. Blindman-Walking Optimization Method

    Directory of Open Access Journals (Sweden)

    Chunming Li

    2010-12-01

    Full Text Available Optimization methods are all implemented with the hypothesis of unknowing the mathematic express of objective objection. Using the human analogy innovative method, the one-dimension blind-walking optimal method is proposed in this paper. The theory and the algorithm of this method includes halving, doubling, reversing probing step and verifying the applicability condition. Double-step is available to make current point moving to the extremum point. Half-step is available to accelerate convergence. In order to improve the optimization, the applicability condition decides whether update current point or not. The operation process, algorithmic flow chart and characteristic analysis of the method were given. Two optimization problems with unimodal or multimodal objective function were solved by the proposed method respectively. The simulation result shows that the proposed method is better than the ordinary method. The proposed method has the merit of rapid convergence, little calculation capacity, wide applicable range, etc. Taking the method as innovative kernel, the random research method, feasible direction method and complex shape method were improved. Taking the innovative content of this paper as innovative kernel, a monograph was published. The other innovations of the monograph are listed, such as applied algorithm of Karush-Kuhn-Tucker (KKT qualifications on judging the restriction extremum point, the design step of computing software, the complementarity and derivation of Powell criterion, the method of keeping the complex shape not to deduce dimension and the analysis of gradual optimization characteristic, the reinforced wall of inner point punish function method, the analysis of problem with constrained monstrosity extremum point, the improvement of Newton method and the validation of optimization idea of blind walking repeatedly, the explanation of later-day optimization method, the conformity of seeking algorithm needing the

  20. Method of constrained global optimization

    Energy Technology Data Exchange (ETDEWEB)

    Altschuler, E.L.; Williams, T.J.; Ratner, E.R.; Dowla, F.; Wooten, F. (Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, California 94551 (United States) Department of Applied Physics, Stanford University, Stanford, California 94305 (United States) Department of Applied Science, University of California, Davis/Livermore, P.O. Box 808, Livermore, California 94551 (United States))

    1994-04-25

    We present a new method for optimization: constrained global optimization (CGO). CGO iteratively uses a Glauber spin flip probability and the Metropolis algorithm. The spin flip probability allows changing only the values of variables contributing excessively to the function to be minimized. We illustrate CGO with two problems---Thomson's problem of finding the minimum-energy configuration of unit charges on a spherical surface, and a problem of assigning offices---for which CGO finds better minima than other methods. We think CGO will apply to a wide class of optimization problems.

  1. Optimization methods in structural design

    CERN Document Server

    Rothwell, Alan

    2017-01-01

    This book offers an introduction to numerical optimization methods in structural design. Employing a readily accessible and compact format, the book presents an overview of optimization methods, and equips readers to properly set up optimization problems and interpret the results. A ‘how-to-do-it’ approach is followed throughout, with less emphasis at this stage on mathematical derivations. The book features spreadsheet programs provided in Microsoft Excel, which allow readers to experience optimization ‘hands-on.’ Examples covered include truss structures, columns, beams, reinforced shell structures, stiffened panels and composite laminates. For the last three, a review of relevant analysis methods is included. Exercises, with solutions where appropriate, are also included with each chapter. The book offers a valuable resource for engineering students at the upper undergraduate and postgraduate level, as well as others in the industry and elsewhere who are new to these highly practical techniques.Whi...

  2. Topology Optimization - Improved Checker-Board Filtering With Sharp Contours

    DEFF Research Database (Denmark)

    Pedersen, Christian Gejl; Lund, Jeppe Jessen; Damkilde, Lars

    2006-01-01

    In topology optimization it is mandatory to use a filtering technique in order to prevent checker-boarder solutions. The paper examines a new filtering principle and demonstrates an improved sharpness in the contours. This was not realized in the original proposal of the filter. Furthermore...

  3. Analysis of digital timing methods with DRS4 board

    CERN Document Server

    Du, Cheng-Ming; Yang, Hai-Bo; Cheng, Ke; Zhang, Xiu-Ling; Xu, Hu-Shan; Hu, Zheng-Guo; Sun, Zhi-Yu

    2015-01-01

    Digital Pulse Processing (DPP) modules are being used to replace the analog electronics modular in modern physics experiments for processing the original signals from detectors. A new DPP modules based on domino ring sampler version 4 (DRS4) and multiple methods for processing arrival times are presented in this paper. In the experiments, the detectors were irradiated with 511keV gama ray from a 22Na source.The detectors consitsts of LaBr3 scintillators and XP20D0 Photomultiplier Tubes(PMTs), and the acquiring system was a 8+1 channels DRS4 board.Multiple DPP including (1)leading-edge discrimination, (2)constant-fraction zero-crossing discrimination and (3)digital constant fraction discrimination were inverstigated. The best time resolution is 194.7ps FWHM, obtained by constant fraction discrimination method, which is better than the other DPP methods and the traditional analog systems using the same detectors. The DRS4 board and DPP methods can be applied to supplement positron emission tomography (PET) with...

  4. Optimization of Medical Teaching Methods

    Directory of Open Access Journals (Sweden)

    Wang Fei

    2015-12-01

    Full Text Available In order to achieve the goal of medical education, medicine and adapt to changes in the way doctors work, with the rapid medical teaching methods of modern science and technology must be reformed. Based on the current status of teaching in medical colleges method to analyze the formation and development of medical teaching methods, characteristics, about how to achieve optimal medical teaching methods for medical education teachers and management workers comprehensive and thorough change teaching ideas and teaching concepts provide a theoretical basis.

  5. Optimal control linear quadratic methods

    CERN Document Server

    Anderson, Brian D O

    2007-01-01

    This augmented edition of a respected text teaches the reader how to use linear quadratic Gaussian methods effectively for the design of control systems. It explores linear optimal control theory from an engineering viewpoint, with step-by-step explanations that show clearly how to make practical use of the material.The three-part treatment begins with the basic theory of the linear regulator/tracker for time-invariant and time-varying systems. The Hamilton-Jacobi equation is introduced using the Principle of Optimality, and the infinite-time problem is considered. The second part outlines the

  6. A corrected method of distorted printed circuit board image

    Institute of Scientific and Technical Information of China (English)

    Qiao Nao-Sheng; Ye Yu-Tang; Huang Yong-Lin

    2011-01-01

    This paper proposes a corrected method of distorted image based on adaptive control. First, the adaptive control relationship of pixel point positions between distorted image and its corrected image is given by using polynomial fitting,thus control point pairs between the distorted image and its corrected image are found. Secondly, the value of both image distortion centre and polynomial coefficient is obtained with least square method, thus the relationship of each control point pairs is deduced. In the course of distortion image processing, the gray value of the corrected image is changed into integer with bilinear interpolation. Finally, the experiments are performed to correct two distorted printed circuit board images. The results are perfect and the mean square errors of residual error are tiny.

  7. Harmfulness Evaluation Method for On-Board Water Ballast Management

    Directory of Open Access Journals (Sweden)

    Željko Kurtela

    2009-01-01

    Full Text Available Having identified all the dominant factors and having puttogether a mosaic of all the factors resulting from a ship 's voyage,as well as a number of differently dimensioned criteria, theharmfulness evaluation method for water ballast managementon board has been elaborated. By careful analysis of the impactfactors to which status elements are adjoined, by the assignmentof harmfulness levels to the status elements, by determiningdifficulty factor values, by introduction of treatment methodsi.e. exchange of water ballast, certain characteristic managementscenarios according to ship type are developed. Cumulativescenarios provide insight into the total harmfulness ofwater ballast management. The introduction of a comprehensiveapproach results in the development of different scenariosapplicable to all ships. The established harmfulness evaluationmethod for water ballast management is applicable to all shiptypes, and it has been tested on various types of ships that weredischarging ballast in various ports worldwide.

  8. QUADRATIC OPTIMIZATION METHOD AND ITS APPLICATION ON OPTIMIZING MECHANISM PARAMETER

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yun; CHEN Jianneng; YU Yaxin; YU Gaohong; ZHU Jianping

    2006-01-01

    In order that the mechanism designed meets the requirements of kinematics with optimal dynamics behaviors, a quadratic optimization method is proposed based on the different characteristics of kinematic and dynamic optimization. This method includes two steps of optimization, that is, kinematic and dynamic optimization. Meanwhile, it uses the results of the kinematic optimization as the constraint equations of dynamic optimization. This method is used in the parameters optimization of transplanting mechanism with elliptic planetary gears of high-speed rice seedling transplanter with remarkable significance. The parameters spectrum, which meets to the kinematic requirements, is obtained through visualized human-computer interactions in the kinematics optimization, and the optimal parameters are obtained based on improved genetic algorithm in dynamic optimization. In the dynamic optimization, the objective function is chosen as the optimal dynamic behavior and the constraint equations are from the results of the kinematic optimization. This method is suitable for multi-objective optimization when both the kinematic and dynamic performances act as objective functions.

  9. Electrostatic separation for recycling waste printed circuit board: a study on external factor and a robust design for optimization.

    Science.gov (United States)

    Hou, Shibing; Wu, Jiang; Qin, Yufei; Xu, Zhenming

    2010-07-01

    Electrostatic separation is an effective and environmentally friendly method for recycling waste printed circuit board (PCB) by several kinds of electrostatic separators. However, some notable problems have been detected in its applications and cannot be efficiently resolved by optimizing the separation process. Instead of the separator itself, these problems are mainly caused by some external factors such as the nonconductive powder (NP) and the superficial moisture of feeding granule mixture. These problems finally lead to an inefficient separation. In the present research, the impacts of these external factors were investigated and a robust design was built to optimize the process and to weaken the adverse impact. A most robust parameter setting (25 kv, 80 rpm) was concluded from the experimental design. In addition, some theoretical methods, including cyclone separation, were presented to eliminate these problems substantially. This will contribute to efficient electrostatic separation of waste PCB and make remarkable progress for industrial applications.

  10. Electromagnetics and antenna optimization using Taguchi's method

    CERN Document Server

    Weng, Wei-Chung

    2007-01-01

    This book presents a new global optimization technique using Taguchi's method and its applications in electromagnetics and antenna engineering. Compared with traditional optimization techniques, Taguchi's optimization method is easy to implement and very efficient in reaching optimum solutions.Taguchi's optimization method is developed based on the orthogonal array (OA) concept, which offers a systematic and efficient way to select design parameters. The book illustrates the basic implementation procedure of Taguchi's optimization method and discusses various advanced techniques for performanc

  11. Controlling Small Fixed Wing UAVs to Optimize Image Quality from On-Board Cameras

    Science.gov (United States)

    Jackson, Stephen Phillip

    Small UAVs have shown great promise as tools for collecting aerial imagery both quickly and cheaply. Furthermore, using a team of small UAVs, as opposed to one large UAV, has shown promise as being a cheaper, faster and more robust method for collecting image data over a large area. Unfortunately, the autonomy of small UAVs has not yet reached the point where they can be relied upon to collect good aerial imagery without human intervention, or supervision. The work presented here intends to increase the level of autonomy of small UAVs so that they can independently, and reliably collect quality aerial imagery. The main contribution of this paper is a novel approach to controlling small fixed wing UAVs that optimizes the quality of the images captured by cameras on board the aircraft. This main contribution is built on three minor contributions: a kinodynamic motion model for small fixed wing UAVs, an iterative Gaussian sampling strategy for rapidly exploring random trees, and a receding horizon, nonlinear model predictive controller for controlling a UAV's sensor footprint. The kinodynamic motion model is built on the traditional unicycle model of an aircraft. In order to create dynamically feasible paths, the kinodynamic motion model augments the kinetic unicycle model by adding a first order estimate of the aircraft's roll dynamics. Experimental data is presented that not only validates this novel kinodynamic motion model, but also shows a 25% improvement over the traditional unicycle model. A novel Gaussian biased sampling strategy is presented for building a rapidly exploring random tree that quickly iterates to a near optimal path. This novel sampling strategy does not require a method for calculating the nearest node to a point, which means that it runs much faster than the traditional RRT algorithm, but it still results in a Gaussian distribution of nodes. Furthermore, because it uses the kinodynamic motion model, the near optimal path it generates is, by

  12. Artificial Neural Networks Applications: from Aircraft Design Optimization to Orbiting Spacecraft On-board Environment Monitoring

    Science.gov (United States)

    Jules, Kenol; Lin, Paul P.

    2002-01-01

    This paper reviews some of the recent applications of artificial neural networks taken from various works performed by the authors over the last four years at the NASA Glenn Research Center. This paper focuses mainly on two areas. First, artificial neural networks application in design and optimization of aircraft/engine propulsion systems to shorten the overall design cycle. Out of that specific application, a generic design tool was developed, which can be used for most design optimization process. Second, artificial neural networks application in monitoring the microgravity quality onboard the International Space Station, using on-board accelerometers for data acquisition. These two different applications are reviewed in this paper to show the broad applicability of artificial intelligence in various disciplines. The intent of this paper is not to give in-depth details of these two applications, but to show the need to combine different artificial intelligence techniques or algorithms in order to design an optimized or versatile system.

  13. Application of On-Board Evolutionary Algorithms to Underwater Robots to Optimally Replan Missions with Energy Constraints

    Directory of Open Access Journals (Sweden)

    M. L. Seto

    2012-01-01

    Full Text Available The objective is to show that on-board mission replanning for an AUV sensor coverage mission, based on available energy, enhances mission success. Autonomous underwater vehicles (AUVs are tasked to increasingly long deployments, consequently energy management issues are timely and relevant. Energy shortages can occur if the AUV unexpectedly travels against stronger currents, is not trimmed for the local water salinity has to get back on course, and so forth. An on-board knowledge-based agent, based on a genetic algorithm, was designed and validated to replan a near-optimal AUV survey mission. It considers the measured AUV energy consumption, attitudes, speed over ground, and known response to proposed missions through on-line dynamics and control predictions. For the case studied, the replanned mission improves the survey area coverage by a factor of 2 for an energy budget, that is, a factor of 2 less than planned. The contribution is a novel on-board cognitive capability in the form of an agent that monitors the energy and intelligently replans missions based on energy considerations with evolutionary methods.

  14. Adaptive scalarization methods in multiobjective optimization

    CERN Document Server

    Eichfelder, Gabriele

    2008-01-01

    This book presents adaptive solution methods for multiobjective optimization problems based on parameter dependent scalarization approaches. Readers will benefit from the new adaptive methods and ideas for solving multiobjective optimization.

  15. Optimal Thermo-Structural Analysis for High Density Package Mounting on Build-up Board

    Science.gov (United States)

    Nakanishi, Tohru; Hase, Tomohiro

    The importance of the high density packaging technology and mounting technology on the printed wiring build-up board has been increased for the consumer electric products. On the other hand, the chance to use the build-up boards for mounting the high density packages has been increased. However, the understanding that the reliability of the solder connection depends on the structure of the package, the motherboard, and the material properties, is not very high. In this paper, the reliability for high density packaging, mounted on the build-up board, is assessed. The compact numerical analysis model for the reliability assessment is suggested and the most reliable packaging design with optimizing each of the parameters is reported. For introduction to the reliability assessment of the FCA attachment, ceramic and silicon are compared as the inter-poser with the parameter of the solder height. The verification of the numerical analysis results using tests on the actual hardware is also shown. And the established numerical analysis model is applied to the study of influence of the copper balance between the front side and the back side copper layers.

  16. 高频板ICD改善方法及钻孔参数优化研究%Study on improve high-frequency board ICD method and drilling parameters optimization

    Institute of Scientific and Technical Information of China (English)

    李丰; 杨巧云; 杜明星; 朱拓

    2013-01-01

    高频高速材料具有优良的介电性能和耐热性,但由于独特的化学性能,该材料在加工中存在很大问题,特别是ICD(内层互连不良)、灯芯、钉头、内层孔壁分离等不良现象。文章通过采用DOE试验优化设计和钻孔参数以改善上述不良问题。%High frequency material has excellent dielectric properties and heat resistance, but because of the special chemical properties, this material has a lot of problems in the production process, especially ICD (the inner micro circuit breaker), wick, nail head, the inner hole wall separation and other undesirable phenomena. In this paper, by using the DOE test optimization and design and drilling parameters, it aims to improve the problem.

  17. Tensor methods for large, sparse unconstrained optimization

    Energy Technology Data Exchange (ETDEWEB)

    Bouaricha, A.

    1996-11-01

    Tensor methods for unconstrained optimization were first introduced by Schnabel and Chow [SIAM J. Optimization, 1 (1991), pp. 293-315], who describe these methods for small to moderate size problems. This paper extends these methods to large, sparse unconstrained optimization problems. This requires an entirely new way of solving the tensor model that makes the methods suitable for solving large, sparse optimization problems efficiently. We present test results for sets of problems where the Hessian at the minimizer is nonsingular and where it is singular. These results show that tensor methods are significantly more efficient and more reliable than standard methods based on Newton`s method.

  18. Numerical methods for stellarator optimization

    Energy Technology Data Exchange (ETDEWEB)

    Morris, R.N.; Hedrick, C.L.; Hirshman, S.P.; Lyon, J.F.; Rome, J.A.

    1989-01-01

    A numerical optimization procedure utilizing an inverse 3-D equilibrium solver, a Mercier stability assessment, a deeply-trapped-particle loss assessment, and a nonlinear optimization package has been used to produce low aspect ratio (A = 4) stellarator designs. These designs combine good stability and improved transport with a compact configuration. 7 refs., 2 figs., 1 tab.

  19. OPTIMIZATION METHODS AND SEO TOOLS

    Directory of Open Access Journals (Sweden)

    Maria Cristina ENACHE

    2014-06-01

    Full Text Available SEO is the activity of optimizing Web pages or whole sites in order to make them more search engine friendly, thus getting higher positions in search results. Search engine optimization (SEO involves designing, writing, and coding a website in a way that helps to improve the volume and quality of traffic to your website from people using search engines. While Search Engine Optimization is the focus of this booklet, keep in mind that it is one of many marketing techniques. A brief overview of other marketing techniques is provided at the end of this booklet.

  20. Reliability-based concurrent subspace optimization method

    Institute of Scientific and Technical Information of China (English)

    FAN Hui; LI Wei-ji

    2008-01-01

    To avoid the high computational cost and much modification in the process of applying traditional re-liability-based design optimization method, a new reliability-based concurrent subspace optimization approach is proposed based on the comparison and analysis of the existing muhidisciplinary optimization techniques and reli-ability assessment methods. It is shown through a canard configuration optimization for a three-surface transport that the proposed method is computationally efficient and practical with the least modification to the current de-terministic optimization process.

  1. Citizen advisory boards: An empirical model for choosing goals and methods

    Energy Technology Data Exchange (ETDEWEB)

    Kunsberg, P.

    1994-12-01

    This is a study of Citizen Advisory Boards (CABS) undertaken for the Department of Energy (DOE) to draw practical insights from the accumulated experience of CAB members and agency officials who have worked with these boards over many years. Hence the main research tool is in-depth interviews of these individuals. In addition, the study relies on field observations of CABs at work, historical documentation of individual boards, and a large body of academic, professional, and government literature. The DOE is in the process of establishing Site Specific Advisory Boards (SSABs) at most of its major facilities in order to provide for community involvement in the DOE environmental restoration and environmental management programs, but these boards initiated by DOE do not yet have enough of a track-record for a study of this type. Consequently, the study focused on CABs at six other federal agencies which have had substantial experience with boards that are similar in composition and purpose to the SSABs. The study examined common problem that confront virtually every CAB in its organization and its decision-making process. For example, each board faces difficult issues in defining its goals and representational responsibilities, selection of members, selection of issues, reaching agreement on recommendations to the parent agency, getting responsive action from the parent agency, and evaluating the board`s success over time. An effort was made to identify solutions or best approaches to these fundamental problems such that the recommended approach has broad application to citizen advisory boards concerned with environmental issues. The conclusions of the study are summarized in a model which incorporates the optimal approaches discovered with respect to each of the critical issues. While acknowledging that the particular circumstances of a CAB may call for individual variations, the model provides a fairly comprehensive description of recommended features of a CAB.

  2. Quadrupole gradient coil design and optimization: a printed circuit board approach.

    Science.gov (United States)

    Chu, K; Rutt, B K

    1994-06-01

    Three different dual-axis quadrupole gradient coils for quantitative high resolution MR imaging of small animals, phantoms and specimens were designed and built using printed circuit board technology. Numerical optimization of the conductor positions was used to increase the volume of 0.4% gradient uniformity by up to a factor of four. In one coil, the volume of 5% gradient uniformity occupied 88% and 83% of the overall diameter and length of the coil, respectively. A systematic error of 0.5% in the wire placement was shown to cause a reduction in the volume of 0.4% gradient uniformity by a factor of two, though the region of 5% gradient uniformity was not significantly affected. Heat transfer calculations were used to determine maximum peak and root-mean-squared currents that could safely be applied to the coils.

  3. Overview of multi-objective optimization methods

    Institute of Scientific and Technical Information of China (English)

    雷秀娟; 史忠科

    2004-01-01

    To assist readers to have a comprehensive understanding, the classical and intelligent methods roundly based on precursory research achievements are summarized in this paper. First, basic conception and description about multi-objective (MO) optimization are introduced. Then some definitions and related terminologies are given. Furthermore several MO optimization methods including classical and current intelligent methods are discussed one by one succinctly. Finally evaluations on advantages and disadvantages about these methods are made at the end of the paper.

  4. Sampling uncertainty evaluation for data acquisition board based on Monte Carlo method

    Science.gov (United States)

    Ge, Leyi; Wang, Zhongyu

    2008-10-01

    Evaluating the data acquisition board sampling uncertainty is a difficult problem in the field of signal sampling. This paper analyzes the sources of dada acquisition board sampling uncertainty in the first, then introduces a simulation theory of dada acquisition board sampling uncertainty evaluation based on Monte Carlo method and puts forward a relation model of sampling uncertainty results, sampling numbers and simulation times. In the case of different sample numbers and different signal scopes, the author establishes a random sampling uncertainty evaluation program of a PCI-6024E data acquisition board to execute the simulation. The results of the proposed Monte Carlo simulation method are in a good agreement with the GUM ones, and the validities of Monte Carlo method are represented.

  5. Experimental validation of structural optimization methods

    Science.gov (United States)

    Adelman, Howard M.

    1992-01-01

    The topic of validating structural optimization methods by use of experimental results is addressed. The need for validating the methods as a way of effecting a greater and an accelerated acceptance of formal optimization methods by practicing engineering designers is described. The range of validation strategies is defined which includes comparison of optimization results with more traditional design approaches, establishing the accuracy of analyses used, and finally experimental validation of the optimization results. Examples of the use of experimental results to validate optimization techniques are described. The examples include experimental validation of the following: optimum design of a trussed beam; combined control-structure design of a cable-supported beam simulating an actively controlled space structure; minimum weight design of a beam with frequency constraints; minimization of the vibration response of helicopter rotor blade; minimum weight design of a turbine blade disk; aeroelastic optimization of an aircraft vertical fin; airfoil shape optimization for drag minimization; optimization of the shape of a hole in a plate for stress minimization; optimization to minimize beam dynamic response; and structural optimization of a low vibration helicopter rotor.

  6. DESIGN OPTIMIZATION METHOD USED IN MECHANICAL ENGINEERING

    Directory of Open Access Journals (Sweden)

    SCURTU Iacob Liviu

    2016-11-01

    Full Text Available This paper presents an optimization study in mechanical engineering. First part of the research describe the structural optimization method used, followed by the presentation of several optimization studies conducted in recent years. The second part of the paper presents the CAD modelling of an agricultural plough component. The beam of the plough is analysed using finite element method. The plough component is meshed in solid elements, and the load case which mimics the working conditions of agricultural equipment of this are created. The model is prepared to find the optimal structural design, after the FEA study of the model is done. The mass reduction of part is the criterion applied for this optimization study. The end of this research presents the final results and the model optimized shape.

  7. The diet board: welfare impacts of a novel method of dietary restriction in laboratory rats

    DEFF Research Database (Denmark)

    Kasanen, I H E; Inhilä, K J; Vainio, O M

    2009-01-01

    Laboratory rats are commonly fed ad libitum (AL). Moderate dietary restriction (DR) decreases mortality and morbidity when compared with AL feeding, but there are several obstacles to the implementation of DR. Traditional methods of restricted feeding disrupt normal diurnal eating rhythms...... and are not compatible with group housing. We have designed a novel method, the diet board, to restrict the feeding of group-housed rats. Animals fed from the diet board had 15% lower body weight than the AL-fed animals at the age of 17 weeks. The welfare effects of diet board feeding were assessed by comparing...... to solve the health problems associated with AL feeding, while allowing the rats to be group-housed and to maintain their normal diurnal eating rhythms. The diet board can also be seen as a functional cage furniture item, dividing the cage into compartments and thus increasing the structural complexity...

  8. Multidisciplinary Optimization Methods for Aircraft Preliminary Design

    Science.gov (United States)

    Kroo, Ilan; Altus, Steve; Braun, Robert; Gage, Peter; Sobieski, Ian

    1994-01-01

    This paper describes a research program aimed at improved methods for multidisciplinary design and optimization of large-scale aeronautical systems. The research involves new approaches to system decomposition, interdisciplinary communication, and methods of exploiting coarse-grained parallelism for analysis and optimization. A new architecture, that involves a tight coupling between optimization and analysis, is intended to improve efficiency while simplifying the structure of multidisciplinary, computation-intensive design problems involving many analysis disciplines and perhaps hundreds of design variables. Work in two areas is described here: system decomposition using compatibility constraints to simplify the analysis structure and take advantage of coarse-grained parallelism; and collaborative optimization, a decomposition of the optimization process to permit parallel design and to simplify interdisciplinary communication requirements.

  9. Data compression on board the PLANCK Satellite Low Frequency Instrument optimal compression rate

    CERN Document Server

    Gaztañaga, E; Romeo, A; Fosalba, P; Elizalde, E

    1998-01-01

    Data on board the future PLANCK Low Frequency Instrument (LFI), to measure the Cosmic Microwave Background (CMB) anisotropies, consist of $N$ differential temperature measurements, expanding a range of values we shall call $R$. Preliminary studies and telemetry allocation indicate the need of compressing these data by a ratio of $c_r \\simgt 10$. Here we present a study of entropy for (correlated multi-Gaussian discrete) noise, showing how the optimal compression $c_{r,opt}$, for a linearly discretized data set with $N_{bits}=\\log_2{N_{max}}$ bits is given by: $c_r \\simeq {N_{bits}/\\log_2(\\sqrt{2\\pi e} ~\\sigma_e/\\Delta)}$, where $\\sigma_e\\equiv (det C)^{1/2N}$ is some effective noise rms given by the covariance matrix $C$ and to be as small as the instrumental white noise RMS: $\\Delta \\simeq \\sigma_T averaging). Within the currently proposed $N_{bits}=16$ representation, a linear analogue to digital converter (ADC) will allow the digital storage of a large dynamic range of differential temperature $R= N_{max} ...

  10. Topology optimization using the finite volume method

    DEFF Research Database (Denmark)

    Gersborg-Hansen, Allan; Bendsøe, Martin P.; Sigmund, Ole

    Computational procedures for topology optimization of continuum problems using a material distribution method are typically based on the application of the finite element method (FEM) (see, e.g. [1]). In the present work we study a computational framework based on the finite volume method (FVM, see......, e.g. [2]) in order to develop methods for topology design for applications where conservation laws are critical such that element--wise conservation in the discretized models has a high priority. This encompasses problems involving for example mass and heat transport. The work described...... in this presentation is focused on a prototype model for topology optimization of steady heat diffusion. This allows for a study of the basic ingredients in working with FVM methods when dealing with topology optimization problems. The FVM and FEM based formulations differ both in how one computes the design...

  11. A topological derivative method for topology optimization

    DEFF Research Database (Denmark)

    Norato, J.; Bendsøe, Martin P.; Haber, RB;

    2007-01-01

    resource constraint. A smooth and consistent projection of the region bounded by the level set onto the fictitious analysis domain simplifies the response analysis and enhances the convergence of the optimization algorithm. Moreover, the projection supports the reintroduction of solid material in void......We propose a fictitious domain method for topology optimization in which a level set of the topological derivative field for the cost function identifies the boundary of the optimal design. We describe a fixed-point iteration scheme that implements this optimality criterion subject to a volumetric...... regions, a critical requirement for robust topology optimization. We present several numerical examples that demonstrate compliance minimization of fixed-volume, linearly elastic structures....

  12. Computer-aided interactive structural optimization of printed-circuit-board design

    Science.gov (United States)

    Duncan, L. B.; Holman, R. E.; Lagasse, B. K.; Sakamoto, L. W.; Sunada, W. H.

    Electronic equipment operating in severe vibration environments plays a critical role in military and aerospace hardware. A crucial element of most modularized electronic equipment is the printed circuit board (PCB). Structural failures of such boards are almost entirely the result of imposed mechanical vibration. It is desirable to incorporate structural guidelines and analysis techniques at an early stage in board development when deficiencies may easily be corrected. However, there are a number of problems connected with such an approach. A computer program has been developed to address the considered situation. The program is to reduce PCB structural analysis to a level readily understood by the average designer. Another objective of the program is to encourage use of structural analysis at an early stage of PCB design and development. Attention is given to board geometry, program organization, board response computation, and a sample problem.

  13. Optimization of an on-board imaging system for extremely rapid radiation therapy

    Energy Technology Data Exchange (ETDEWEB)

    Cherry Kemmerling, Erica M.; Wu, Meng, E-mail: mengwu@stanford.edu; Yang, He; Fahrig, Rebecca [Department of Radiology, Stanford University, Stanford, California 94305 (United States); Maxim, Peter G.; Loo, Billy W. [Department of Radiation Oncology, Stanford University, Stanford, California 94305 and Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California 94305 (United States)

    2015-11-15

    Purpose: Next-generation extremely rapid radiation therapy systems could mitigate the need for motion management, improve patient comfort during the treatment, and increase patient throughput for cost effectiveness. Such systems require an on-board imaging system that is competitively priced, fast, and of sufficiently high quality to allow good registration between the image taken on the day of treatment and the image taken the day of treatment planning. In this study, three different detectors for a custom on-board CT system were investigated to select the best design for integration with an extremely rapid radiation therapy system. Methods: Three different CT detectors are proposed: low-resolution (all 4 × 4 mm pixels), medium-resolution (a combination of 4 × 4 mm pixels and 2 × 2 mm pixels), and high-resolution (all 1 × 1 mm pixels). An in-house program was used to generate projection images of a numerical anthropomorphic phantom and to reconstruct the projections into CT datasets, henceforth called “realistic” images. Scatter was calculated using a separate Monte Carlo simulation, and the model included an antiscatter grid and bowtie filter. Diagnostic-quality images of the phantom were generated to represent the patient scan at the time of treatment planning. Commercial deformable registration software was used to register the diagnostic-quality scan to images produced by the various on-board detector configurations. The deformation fields were compared against a “gold standard” deformation field generated by registering initial and deformed images of the numerical phantoms that were used to make the diagnostic and treatment-day images. Registrations of on-board imaging system data were judged by the amount their deformation fields differed from the corresponding gold standard deformation fields—the smaller the difference, the better the system. To evaluate the registrations, the pointwise distance between gold standard and realistic registration

  14. Boolean methods of optimization over independence systems

    Energy Technology Data Exchange (ETDEWEB)

    Hulme, B.L.

    1983-01-01

    This paper presents both a direct and an iterative method of solving the combinatorial optimization problem associated with any independence system. The methods use Boolean algebraic computations to produce solutions. In addition, the iterative method employs a version of the greedy algorithm both to compute upper bounds on the optimum value and to produce the additional circuits needed at every stage. The methods are extensions of those used to solve a problem of fire protection at nuclear reactor power plants.

  15. The optimal homotopy asymptotic method engineering applications

    CERN Document Server

    Marinca, Vasile

    2015-01-01

    This book emphasizes in detail the applicability of the Optimal Homotopy Asymptotic Method to various engineering problems. It is a continuation of the book “Nonlinear Dynamical Systems in Engineering: Some Approximate Approaches”, published at Springer in 2011, and it contains a great amount of practical models from various fields of engineering such as classical and fluid mechanics, thermodynamics, nonlinear oscillations, electrical machines, and so on. The main structure of the book consists of 5 chapters. The first chapter is introductory while the second chapter is devoted to a short history of the development of homotopy methods, including the basic ideas of the Optimal Homotopy Asymptotic Method. The last three chapters, from Chapter 3 to Chapter 5, are introducing three distinct alternatives of the Optimal Homotopy Asymptotic Method with illustrative applications to nonlinear dynamical systems. The third chapter deals with the first alternative of our approach with two iterations. Five application...

  16. Topology optimization using the finite volume method

    DEFF Research Database (Denmark)

    Computational procedures for topology optimization of continuum problems using a material distribution method are typically based on the application of the finite element method (FEM) (see, e.g. [1]). In the present work we study a computational framework based on the finite volume method (FVM, see...... in this presentation is focused on a prototype model for topology optimization of steady heat diffusion. This allows for a study of the basic ingredients in working with FVM methods when dealing with topology optimization problems. The FVM and FEM based formulations differ both in how one computes the design...... derivative of the system matrix K and in how one computes the discretized version of certain objective functions. Thus for a cost function for minimum dissipated energy (like minimum compliance for an elastic structure) one obtains an expression c = u^\\T \\tilde{K}u $, where \\tilde{K} is different from K...

  17. Topology optimization using the finite volume method

    DEFF Research Database (Denmark)

    Gersborg-Hansen, Allan; Bendsøe, Martin P.; Sigmund, Ole

    Computational procedures for topology optimization of continuum problems using a material distribution method are typically based on the application of the finite element method (FEM) (see, e.g. [1]). In the present work we study a computational framework based on the finite volume method (FVM, see...... in this presentation is focused on a prototype model for topology optimization of steady heat diffusion. This allows for a study of the basic ingredients in working with FVM methods when dealing with topology optimization problems. The FVM and FEM based formulations differ both in how one computes the design...... $, where $\\tilde{\\mathbf K}$ is different from $\\mathbf K $; in a FEM scheme these matrices are equal following the principle of virtual work. Using a staggered mesh and averaging procedures consistent with the FVM the checkerboard problem is eliminated. Two averages are compared to FE solutions, being...

  18. Topology optimization using the finite volume method

    DEFF Research Database (Denmark)

    Computational procedures for topology optimization of continuum problems using a material distribution method are typically based on the application of the finite element method (FEM) (see, e.g. [1]). In the present work we study a computational framework based on the finite volume method (FVM, see...... the well known Reuss lower bound. [1] Bendsøe, M.P.; Sigmund, O. 2004: Topology Optimization - Theory, Methods, and Applications. Berlin Heidelberg: Springer Verlag [2] Versteeg, H. K.; W. Malalasekera 1995: An introduction to Computational Fluid Dynamics: the Finite Volume Method. London: Longman......, e.g. [2]) in order to develop methods for topology design for applications where conservation laws are critical such that element--wise conservation in the discretized models has a high priority. This encompasses problems involving for example mass and heat transport. The work described...

  19. State space Newton's method for topology optimization

    DEFF Research Database (Denmark)

    Evgrafov, Anton

    2014-01-01

    We introduce a new algorithm for solving certain classes of topology optimization problems, which enjoys fast local convergence normally achieved by the full space methods while working in a smaller reduced space. The computational complexity of Newton’s direction finding subproblem in the algori......We introduce a new algorithm for solving certain classes of topology optimization problems, which enjoys fast local convergence normally achieved by the full space methods while working in a smaller reduced space. The computational complexity of Newton’s direction finding subproblem...

  20. An introduction to harmony search optimization method

    CERN Document Server

    Wang, Xiaolei; Zenger, Kai

    2014-01-01

    This brief provides a detailed introduction, discussion and bibliographic review of the nature1-inspired optimization algorithm called Harmony Search. It uses a large number of simulation results to demonstrate the advantages of Harmony Search and its variants and also their drawbacks. The authors show how weaknesses can be amended by hybridization with other optimization methods. The Harmony Search Method with Applications will be of value to researchers in computational intelligence in demonstrating the state of the art of research on an algorithm of current interest. It also helps researche

  1. Optimization Methods in Emotion Recognition System

    Directory of Open Access Journals (Sweden)

    L. Povoda

    2016-09-01

    Full Text Available Emotions play big role in our everyday communication and contain important information. This work describes a novel method of automatic emotion recognition from textual data. The method is based on well-known data mining techniques, novel approach based on parallel run of SVM (Support Vector Machine classifiers, text preprocessing and 3 optimization methods: sequential elimination of attributes, parameter optimization based on token groups, and method of extending train data sets during practical testing and production release final tuning. We outperformed current state of the art methods and the results were validated on bigger data sets (3346 manually labelled samples which is less prone to overfitting when compared to related works. The accuracy achieved in this work is 86.89% for recognition of 5 emotional classes. The experiments were performed in the real world helpdesk environment, was processing Czech language but the proposed methodology is general and can be applied to many different languages.

  2. Adaptive finite element method for shape optimization

    KAUST Repository

    Morin, Pedro

    2012-01-16

    We examine shape optimization problems in the context of inexact sequential quadratic programming. Inexactness is a consequence of using adaptive finite element methods (AFEM) to approximate the state and adjoint equations (via the dual weighted residual method), update the boundary, and compute the geometric functional. We present a novel algorithm that equidistributes the errors due to shape optimization and discretization, thereby leading to coarse resolution in the early stages and fine resolution upon convergence, and thus optimizing the computational effort. We discuss the ability of the algorithm to detect whether or not geometric singularities such as corners are genuine to the problem or simply due to lack of resolution - a new paradigm in adaptivity. © EDP Sciences, SMAI, 2012.

  3. [Limb-length measurements using wooden boards: an accurate and experience-independent method

    NARCIS (Netherlands)

    Pakvis, D.F.M.; Jaarsma, R.L.; Kampen, A. van

    2003-01-01

    OBJECTIVE: To determine the precision and reliability of the indirect limb-length measurement, and the inter-observer variance between doctors differing in level of experience. DESIGN: Descriptive. METHOD: Indirect limb-length measurement by placing 0.5 cm-thick wooden boards under the foot of the s

  4. THE DEVELOPMENT OF METHOD AND ON-BOARD DEVICES FOR COLLISION AVOIDANCE WHEN OVERTAKING

    Directory of Open Access Journals (Sweden)

    Podryhalo, M.

    2013-06-01

    Full Text Available A method for improving the safety of overtaking maneuver by using the on-board collision avoidance system, which has an increased assessment reliability of safety of vehicles overtaking that move in the same direction is offered. The proposed system takes into account the main factors that affect the overtaking maneuver.

  5. Method for optimizing harvesting of crops

    DEFF Research Database (Denmark)

    2008-01-01

      In order e.g. to optimize harvesting crops of the kind which may be self dried on a field prior to a harvesting step (116, 118), there is disclosed a method of providing a mobile unit (102) for working (114, 116, 118) the field with crops, equipping the mobile unit (102) with crop biomass...

  6. Non-probabilistic Robust Optimal Design Method

    Institute of Scientific and Technical Information of China (English)

    SUN Wei; XU Huanwei; ZHANG Xu

    2009-01-01

    For the purpose of dealing with uncertainty factors in engineering optimization problems, this paper presents a new non-probabilistic robust optimal design method based on maximum variation estimation. The method analyzes the effect of uncertain factors to objective and constraints functions, and then the maximal variations to a solution are calculated. In order to guarantee robust feasibility the maximal variations of constraints are added to original constraints as penalty term; the maximal variation of objective function is taken as a robust index to a solution; linear physical programming is used to adjust the values of quality characteristic and quality variation, and then a bi-level mathematical robust optimal model is coustructed. The method does not require presumed probability distribution of uncertain factors or continuous and differentiable of objective and constraints functions. To demonstrate the proposed method, the design of the two-bar structure acted by concentrated load is presented. In the example the robustness of the normal stress, feasibility of the total volume and the buckling stress are studied. The robust optimal design results show that in the condition of maintaining feasibility robustness, the proposed approach can obtain a robust solution which the designer is satisfied with the value of objective function and its variation.

  7. Models and Methods for Free Material Optimization

    DEFF Research Database (Denmark)

    Weldeyesus, Alemseged Gebrehiwot

    FMO problem formulations with stress constraints. These problems are highly nonlinear and lead to the so-called singularity phenomenon. The method described in the thesis has successfully solved these problems. In the numerical experiments the stress constraints have been satisfied with high...... conditions for physical attainability, in the context that, it has to be symmetric and positive semidefinite. FMO problems have been studied for the last two decades in many articles that led to the development of a wide range of models, methods, and theories. As the design variables in FMO are the local....... These problems are more difficult to solve and demand higher computational efforts than the standard optimization problems. The focus of today’s development of solution methods for FMO problems is based on first-order methods that require a large number of iterations to obtain optimal solutions. The scope...

  8. Dead time optimization method for power converter

    Science.gov (United States)

    Deselaers, C.; Bergmann, U.; Gronwald, F.

    2013-07-01

    This paper introduces a method for dead time optimization in variable speed motor drive systems. The aim of this method is to reduce the conduction time of the freewheeling diode to a minimum without generation of cross conduction. This results in lower losses, improved EMC, and less overshooting of the phase voltage. The principle of the method is to detect beginning cross currents without adding additional components in the half bridge like resistors or inductances. Only the wave shape of the phase voltage needs to be monitored during switching. This is illustrated by an application of the method to a real power converter.

  9. PART BUILDING ORIENTATION OPTIMIZATION METHOD IN STEREOLITHOGRAPHY

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Aiming at the part quality and building time problems in stereolithography (SL) caused by unreasonable building orientation, a part building orientation decision method in SL rapid prototyping (RP) is carried out. Bringing into full consideration of the deformation, stair-stepping effect, overcure effect and building time related to the part fabrication orientation, and using evaluation function method, a multi-objective optimization model for the building orientation is defined. According to the difference in the angles between normal vectors of triangular facets in standard triangulation language (STL) model and z axis, the expressions of deformation area, stair-stepping area, overcure area are established. According to the characteristics in SL process, part building time is divided into four sections, that is, hatching scanning time, outline scanning time, support building time and layer waiting time. Expressions of each building time section are given. Considering the features of this optimization model, genetic algorithm (GA) is used to derive the optimization objective, related software is developed and optimization results are tested through experiments. Application shows that this method can effectively solve the quality and efficiency troubles caused by unreasonable part building orientation, an automatic orientation-determining program is developed and verified through test.

  10. On the wavelet optimized finite difference method

    Science.gov (United States)

    Jameson, Leland

    1994-01-01

    When one considers the effect in the physical space, Daubechies-based wavelet methods are equivalent to finite difference methods with grid refinement in regions of the domain where small scale structure exists. Adding a wavelet basis function at a given scale and location where one has a correspondingly large wavelet coefficient is, essentially, equivalent to adding a grid point, or two, at the same location and at a grid density which corresponds to the wavelet scale. This paper introduces a wavelet optimized finite difference method which is equivalent to a wavelet method in its multiresolution approach but which does not suffer from difficulties with nonlinear terms and boundary conditions, since all calculations are done in the physical space. With this method one can obtain an arbitrarily good approximation to a conservative difference method for solving nonlinear conservation laws.

  11. Layout optimization with algebraic multigrid methods

    Science.gov (United States)

    Regler, Hans; Ruede, Ulrich

    1993-01-01

    Finding the optimal position for the individual cells (also called functional modules) on the chip surface is an important and difficult step in the design of integrated circuits. This paper deals with the problem of relative placement, that is the minimization of a quadratic functional with a large, sparse, positive definite system matrix. The basic optimization problem must be augmented by constraints to inhibit solutions where cells overlap. Besides classical iterative methods, based on conjugate gradients (CG), we show that algebraic multigrid methods (AMG) provide an interesting alternative. For moderately sized examples with about 10000 cells, AMG is already competitive with CG and is expected to be superior for larger problems. Besides the classical 'multiplicative' AMG algorithm where the levels are visited sequentially, we propose an 'additive' variant of AMG where levels may be treated in parallel and that is suitable as a preconditioner in the CG algorithm.

  12. Reduced basis method for source mask optimization

    CERN Document Server

    Pomplun, J; Burger, S; Schmidt, F; Tyminski, J; Flagello, D; Toshiharu, N; 10.1117/12.866101

    2010-01-01

    Image modeling and simulation are critical to extending the limits of leading edge lithography technologies used for IC making. Simultaneous source mask optimization (SMO) has become an important objective in the field of computational lithography. SMO is considered essential to extending immersion lithography beyond the 45nm node. However, SMO is computationally extremely challenging and time-consuming. The key challenges are due to run time vs. accuracy tradeoffs of the imaging models used for the computational lithography. We present a new technique to be incorporated in the SMO flow. This new approach is based on the reduced basis method (RBM) applied to the simulation of light transmission through the lithography masks. It provides a rigorous approximation to the exact lithographical problem, based on fully vectorial Maxwell's equations. Using the reduced basis method, the optimization process is divided into an offline and an online steps. In the offline step, a RBM model with variable geometrical param...

  13. Adiabatic optimization versus diffusion Monte Carlo methods

    Science.gov (United States)

    Jarret, Michael; Jordan, Stephen P.; Lackey, Brad

    2016-10-01

    Most experimental and theoretical studies of adiabatic optimization use stoquastic Hamiltonians, whose ground states are expressible using only real nonnegative amplitudes. This raises a question as to whether classical Monte Carlo methods can simulate stoquastic adiabatic algorithms with polynomial overhead. Here we analyze diffusion Monte Carlo algorithms. We argue that, based on differences between L1 and L2 normalized states, these algorithms suffer from certain obstructions preventing them from efficiently simulating stoquastic adiabatic evolution in generality. In practice however, we obtain good performance by introducing a method that we call Substochastic Monte Carlo. In fact, our simulations are good classical optimization algorithms in their own right, competitive with the best previously known heuristic solvers for MAX-k -SAT at k =2 ,3 ,4 .

  14. An Integer Programming-Based Generalized Vehicle Routing Approach for Printed Circuit Board Assembly Optimization

    Science.gov (United States)

    Seth, Anupam

    2009-01-01

    Production planning and scheduling for printed circuit, board assembly has so far defied standard operations research approaches due to the size and complexity of the underlying problems, resulting in unexploited automation flexibility. In this thesis, the increasingly popular collect-and-place machine configuration is studied and the assembly…

  15. An Integer Programming-Based Generalized Vehicle Routing Approach for Printed Circuit Board Assembly Optimization

    Science.gov (United States)

    Seth, Anupam

    2009-01-01

    Production planning and scheduling for printed circuit, board assembly has so far defied standard operations research approaches due to the size and complexity of the underlying problems, resulting in unexploited automation flexibility. In this thesis, the increasingly popular collect-and-place machine configuration is studied and the assembly…

  16. Decision-Theoretic Methods in Simulation Optimization

    Science.gov (United States)

    2014-09-24

    Materiel Command REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public reporting burden for this collection of information is...Alamos National Lab: Frazier visited LANL , hosted by Frank Alexander, in January 2013, where he discussed the use of simulation optimization methods for...Alexander, Turab Lookman, and others from LANL , at the Materials Informatics Workshop at the Sante Fe Institute in April 2013. In February 2014, Frazier

  17. Lifecycle-Based Swarm Optimization Method for Numerical Optimization

    Directory of Open Access Journals (Sweden)

    Hai Shen

    2014-01-01

    Full Text Available Bioinspired optimization algorithms have been widely used to solve various scientific and engineering problems. Inspired by biological lifecycle, this paper presents a novel optimization algorithm called lifecycle-based swarm optimization (LSO. Biological lifecycle includes four stages: birth, growth, reproduction, and death. With this process, even though individual organism died, the species will not perish. Furthermore, species will have stronger ability of adaptation to the environment and achieve perfect evolution. LSO simulates Biological lifecycle process through six optimization operators: chemotactic, assimilation, transposition, crossover, selection, and mutation. In addition, the spatial distribution of initialization population meets clumped distribution. Experiments were conducted on unconstrained benchmark optimization problems and mechanical design optimization problems. Unconstrained benchmark problems include both unimodal and multimodal cases the demonstration of the optimal performance and stability, and the mechanical design problem was tested for algorithm practicability. The results demonstrate remarkable performance of the LSO algorithm on all chosen benchmark functions when compared to several successful optimization techniques.

  18. portfolio optimization based on nonparametric estimation methods

    Directory of Open Access Journals (Sweden)

    mahsa ghandehari

    2017-03-01

    Full Text Available One of the major issues investors are facing with in capital markets is decision making about select an appropriate stock exchange for investing and selecting an optimal portfolio. This process is done through the risk and expected return assessment. On the other hand in portfolio selection problem if the assets expected returns are normally distributed, variance and standard deviation are used as a risk measure. But, the expected returns on assets are not necessarily normal and sometimes have dramatic differences from normal distribution. This paper with the introduction of conditional value at risk ( CVaR, as a measure of risk in a nonparametric framework, for a given expected return, offers the optimal portfolio and this method is compared with the linear programming method. The data used in this study consists of monthly returns of 15 companies selected from the top 50 companies in Tehran Stock Exchange during the winter of 1392 which is considered from April of 1388 to June of 1393. The results of this study show the superiority of nonparametric method over the linear programming method and the nonparametric method is much faster than the linear programming method.

  19. Optimized Vertex Method and Hybrid Reliability

    Science.gov (United States)

    Smith, Steven A.; Krishnamurthy, T.; Mason, B. H.

    2002-01-01

    A method of calculating the fuzzy response of a system is presented. This method, called the Optimized Vertex Method (OVM), is based upon the vertex method but requires considerably fewer function evaluations. The method is demonstrated by calculating the response membership function of strain-energy release rate for a bonded joint with a crack. The possibility of failure of the bonded joint was determined over a range of loads. After completing the possibilistic analysis, the possibilistic (fuzzy) membership functions were transformed to probability density functions and the probability of failure of the bonded joint was calculated. This approach is called a possibility-based hybrid reliability assessment. The possibility and probability of failure are presented and compared to a Monte Carlo Simulation (MCS) of the bonded joint.

  20. Swarm Optimization Methods in Microwave Imaging

    Directory of Open Access Journals (Sweden)

    Andrea Randazzo

    2012-01-01

    Full Text Available Swarm intelligence denotes a class of new stochastic algorithms inspired by the collective social behavior of natural entities (e.g., birds, ants, etc.. Such approaches have been proven to be quite effective in several applicative fields, ranging from intelligent routing to image processing. In the last years, they have also been successfully applied in electromagnetics, especially for antenna synthesis, component design, and microwave imaging. In this paper, the application of swarm optimization methods to microwave imaging is discussed, and some recent imaging approaches based on such methods are critically reviewed.

  1. Research on feasibility of computational fluid dynamics (CFD) method for traffic signs board calculation

    Science.gov (United States)

    Chao, S.; Jiao, C. W.; Liu, S.

    2016-08-01

    At this stage of the development of China's highway, the quantity and size of traffic signs are growing with the guiding information increasing. In this paper, a calculation method is provided for special sign board with reducing wind load measures to save construction materials and cost. The empirical model widely used in China is introduced for normal sign structure design. After that, this paper shows a computational fluid dynamics method, which can calculate both normal and special sign structures. These two methods are compared and analyzed with examples to ensure the applicability and feasibility of CFD method.

  2. Binary discrete method of topology optimization

    Institute of Scientific and Technical Information of China (English)

    MEI Yu-lin; WANG Xiao-ming; CHENG Geng-dong

    2007-01-01

    The numerical non-stability of a discrete algorithm of topology optimization can result from the inaccurate evaluation of element sensitivities. Especially, when material is added to elements, the estimation of element sensitivities is very inaccurate,even their signs are also estimated wrong. In order to overcome the problem, a new incremental sensitivity analysis formula is constructed based on the perturbation analysis of the elastic equilibrium increment equation, which can provide us a good estimate of the change of the objective function whether material is removed from or added to elements,meanwhile it can also be considered as the conventional sensitivity formula modified by a non-local element stiffness matrix. As a consequence, a binary discrete method of topology optimization is established, in which each element is assigned either a stiffness value of solid material or a small value indicating no material, and the optimization process can remove material from elements or add material to elements so as to make the objective function decrease. And a main advantage of the method is simple and no need of much mathematics, particularly interesting in engineering application.

  3. METHODS OF INTEGRATED OPTIMIZATION MAGLEV TRANSPORT SYSTEMS

    Directory of Open Access Journals (Sweden)

    A. Lasher

    2013-09-01

    example, this research proved the sustainability of the proposed integrated optimization parameters of transport systems. This approach could be applied not only for MTS, but also for other transport systems. Originality. The bases of the complex optimization of transport presented are the new system of universal scientific methods and approaches that ensure high accuracy and authenticity of calculations with the simulation of transport systems and transport networks taking into account the dynamics of their development. Practical value. The development of the theoretical and technological bases of conducting the complex optimization of transport makes it possible to create the scientific tool, which ensures the fulfillment of the automated simulation and calculating of technical and economic structure and technology of the work of different objects of transport, including its infrastructure.

  4. An on-board near-optimal climb-dash energy management

    Science.gov (United States)

    Weston, A. R.; Cliff, E. M.; Kelley, H. J.

    1982-01-01

    On-board real time flight control is studied in order to develop algorithms which are simple enough to be used in practice, for a variety of missions involving three dimensional flight. The intercept mission in symmetric flight is emphasized. Extensive computation is required on the ground prior to the mission but the ensuing on-board exploitation is extremely simple. The scheme takes advantage of the boundary layer structure common in singular perturbations, arising with the multiple time scales appropriate to aircraft dynamics. Energy modelling of aircraft is used as the starting point for the analysis. In the symmetric case, a nominal path is generated which fairs into the dash or cruise state. Feedback coefficients are found as functions of the remaining energy to go (dash energy less current energy) along the nominal path.

  5. On-board near-optimal climb-dash energy management

    Science.gov (United States)

    Weston, A. R.; Cliff, E. M.; Kelley, H. J.

    1983-01-01

    On-board real time flight control is studied in order to develop algorithms which are simple enough to be used in practice, for a variety of missions involving three dimensional flight. The intercept mission in symmetric flight is emphasized. Extensive computation is required on the ground prior to the mission but the ensuing on-board exploitation is extremely simple. The scheme takes advantage of the boundary layer structure common in singular perturbations, arising with the multiple time scales appropriate to aircraft dynamics. Energy modelling of aircraft is used as the starting point for the analysis. In the symmetric case, a nominal path is generated which fairs into the dash or cruise state.

  6. Methods for Distributed Optimal Energy Management

    DEFF Research Database (Denmark)

    Brehm, Robert

    The presented research deals with the fundamental underlying methods and concepts of how the growing number of distributed generation units based on renewable energy resources and distributed storage devices can be most efficiently integrated into the existing utility grid. In contrast to convent......The presented research deals with the fundamental underlying methods and concepts of how the growing number of distributed generation units based on renewable energy resources and distributed storage devices can be most efficiently integrated into the existing utility grid. In contrast...... to conventional centralised optimal energy flow management systems, here-in, focus is set on how optimal energy management can be achieved in a decentralised distributed architecture such as a multi-agent system. Distributed optimisation methods are introduced, targeting optimisation of energy flow in virtual...... micro-grids by prevention of meteorologic power flows into high voltage grids. A method, based on mathematical optimisation and a consensus algorithm is introduced and evaluated to coordinate charge/discharge scheduling for batteries between a number of buildings in order to improve self...

  7. BOARD-LEVEL BUILT-IN SELF-REPAIR METHOD OF RAM

    Institute of Scientific and Technical Information of China (English)

    Dou Yanjie; Zhan Huiqin; Chen Yakun; Shang Hongliang

    2012-01-01

    This paper describes the method of built-in self-repairing of RAM on board,designs hardware circuit,and logic for the RAM's faults self-repairing system based on FPGA.The key technology is that it utilizes FPGA to test RAM according to some algorithm to find out failure memory units and replace the faulty units with FPGA.Then it can build a memory that has no fault concern to external controller,and realizes the logic binding between external controller and RAM.Micro Controller Unit (MCU) can operate external RAM correctly even if RAM has some fault address units.Conventional MCS-51 is used to simulate the operation of MCU operating external memory.Simulation shows FPGA can complete the faulty address units' mapping and MCU can normally read and write external RAM.This design realizes the RAM's built-in self-repairing on board.

  8. Treatment of printed circuit board industrial wastewater by Ferrite process combined with Fenton method.

    Science.gov (United States)

    Lou, Jie-Chung; Huang, Yu-Jen; Han, Jia-Yun

    2009-10-30

    Printed circuit board wastewater typically contains organics and metal ions. The study explored the feasibility of a sequential procedure, FFP (the combination of the Fenton method and the Ferrite process), for treating printed circuit board wastewater, and established the optimum parameters for it. The analytical results showed that the proper pH level was 2 for Fenton oxidation, and the appropriate H2O2 dosing type was batch dosing. For the Ferrite process, the suitable Fe/M (Fe is the total dose of Fe2+ added to a solution and M is the initial total moles of various metal ions in untreated wastewater) molar ratio was 10 and the sludge met the toxicity characteristic leaching procedure (TCLP) standards. Following FFP treatment, effluent water or sludge easily met Taiwan's standards. Finally, the SEM/EDS test demonstrated that particle sizes of the sludge were approximately 50-80 nm, and the saturation magnetization was 67.5 emu/g.

  9. PRODUCT OPTIMIZATION METHOD BASED ON ANALYSIS OF OPTIMAL VALUES OF THEIR CHARACTERISTICS

    Directory of Open Access Journals (Sweden)

    Constantin D. STANESCU

    2016-05-01

    Full Text Available The paper presents an original method of optimizing products based on the analysis of optimal values of their characteristics . Optimization method comprises statistical model and analytical model . With this original method can easily and quickly obtain optimal product or material .

  10. Optimal Variational Method for Truly Nonlinear Oscillators

    Directory of Open Access Journals (Sweden)

    Vasile Marinca

    2013-01-01

    Full Text Available The Optimal Variational Method (OVM is introduced and applied for calculating approximate periodic solutions of “truly nonlinear oscillators”. The main advantage of this procedure consists in that it provides a convenient way to control the convergence of approximate solutions in a very rigorous way and allows adjustment of convergence regions where necessary. This approach does not depend upon any small or large parameters. A very good agreement was found between approximate and numerical solution, which proves that OVM is very efficient and accurate.

  11. Method for optimizing harvesting of crops

    DEFF Research Database (Denmark)

    2010-01-01

    In order e.g. to optimize harvesting crops of the kind which may be self dried on a field prior to a harvesting step (116, 118), there is disclosed a method of providing a mobile unit (102) for working (114, 116, 118) the field with crops, equipping the mobile unit (102) with crop biomass measuring...... moving the mobile unit on the field and the moisture content (109a, 109b), and determining an optimised drying time (104a, 104b) prior to the following harvesting step (116, 118) in response to the spatial crop biomass and crop moisture content characteristics map and in response to a weather forecast...

  12. Hybrid intelligent optimization methods for engineering problems

    Science.gov (United States)

    Pehlivanoglu, Yasin Volkan

    The purpose of optimization is to obtain the best solution under certain conditions. There are numerous optimization methods because different problems need different solution methodologies; therefore, it is difficult to construct patterns. Also mathematical modeling of a natural phenomenon is almost based on differentials. Differential equations are constructed with relative increments among the factors related to yield. Therefore, the gradients of these increments are essential to search the yield space. However, the landscape of yield is not a simple one and mostly multi-modal. Another issue is differentiability. Engineering design problems are usually nonlinear and they sometimes exhibit discontinuous derivatives for the objective and constraint functions. Due to these difficulties, non-gradient-based algorithms have become more popular in recent decades. Genetic algorithms (GA) and particle swarm optimization (PSO) algorithms are popular, non-gradient based algorithms. Both are population-based search algorithms and have multiple points for initiation. A significant difference from a gradient-based method is the nature of the search methodologies. For example, randomness is essential for the search in GA or PSO. Hence, they are also called stochastic optimization methods. These algorithms are simple, robust, and have high fidelity. However, they suffer from similar defects, such as, premature convergence, less accuracy, or large computational time. The premature convergence is sometimes inevitable due to the lack of diversity. As the generations of particles or individuals in the population evolve, they may lose their diversity and become similar to each other. To overcome this issue, we studied the diversity concept in GA and PSO algorithms. Diversity is essential for a healthy search, and mutations are the basic operators to provide the necessary variety within a population. After having a close scrutiny of the diversity concept based on qualification and

  13. Circular SAR Optimization Imaging Method of Buildings

    Directory of Open Access Journals (Sweden)

    Wang Jian-feng

    2015-12-01

    Full Text Available The Circular Synthetic Aperture Radar (CSAR can obtain the entire scattering properties of targets because of its great ability of 360° observation. In this study, an optimal orientation of the CSAR imaging algorithm of buildings is proposed by applying a combination of coherent and incoherent processing techniques. FEKO software is used to construct the electromagnetic scattering modes and simulate the radar echo. The FEKO imaging results are compared with the isotropic scattering results. On comparison, the optimal azimuth coherent accumulation angle of CSAR imaging of buildings is obtained. Practically, the scattering directions of buildings are unknown; therefore, we divide the 360° echo of CSAR into many overlapped and few angle echoes corresponding to the sub-aperture and then perform an imaging procedure on each sub-aperture. Sub-aperture imaging results are applied to obtain the all-around image using incoherent fusion techniques. The polarimetry decomposition method is used to decompose the all-around image and further retrieve the edge information of buildings successfully. The proposed method is validated with P-band airborne CSAR data from Sichuan, China.

  14. Optimization methods for activities selection problems

    Science.gov (United States)

    Mahad, Nor Faradilah; Alias, Suriana; Yaakop, Siti Zulaika; Arshad, Norul Amanina Mohd; Mazni, Elis Sofia

    2017-08-01

    Co-curriculum activities must be joined by every student in Malaysia and these activities bring a lot of benefits to the students. By joining these activities, the students can learn about the time management and they can developing many useful skills. This project focuses on the selection of co-curriculum activities in secondary school using the optimization methods which are the Analytic Hierarchy Process (AHP) and Zero-One Goal Programming (ZOGP). A secondary school in Negeri Sembilan, Malaysia was chosen as a case study. A set of questionnaires were distributed randomly to calculate the weighted for each activity based on the 3 chosen criteria which are soft skills, interesting activities and performances. The weighted was calculated by using AHP and the results showed that the most important criteria is soft skills. Then, the ZOGP model will be analyzed by using LINGO Software version 15.0. There are two priorities to be considered. The first priority which is to minimize the budget for the activities is achieved since the total budget can be reduced by RM233.00. Therefore, the total budget to implement the selected activities is RM11,195.00. The second priority which is to select the co-curriculum activities is also achieved. The results showed that 9 out of 15 activities were selected. Thus, it can concluded that AHP and ZOGP approach can be used as the optimization methods for activities selection problem.

  15. Computational methods applied to wind tunnel optimization

    Science.gov (United States)

    Lindsay, David

    This report describes computational methods developed for optimizing the nozzle of a three-dimensional subsonic wind tunnel. This requires determination of a shape that delivers flow to the test section, typically with a speed increase of 7 or more and a velocity uniformity of .25% or better, in a compact length without introducing boundary layer separation. The need for high precision, smooth solutions, and three-dimensional modeling required the development of special computational techniques. These include: (1) alternative formulations to Neumann and Dirichlet boundary conditions, to deal with overspecified, ill-posed, or cyclic problems, and to reduce the discrepancy between numerical solutions and boundary conditions; (2) modification of the Finite Element Method to obtain solutions with numerically exact conservation properties; (3) a Matlab implementation of general degree Finite Element solvers for various element designs in two and three dimensions, exploiting vector indexing to obtain optimal efficiency; (4) derivation of optimal quadrature formulas for integration over simplexes in two and three dimensions, and development of a program for semi-automated generation of formulas for any degree and dimension; (5) a modification of a two-dimensional boundary layer formulation to provide accurate flow conservation in three dimensions, and modification of the algorithm to improve stability; (6) development of multi-dimensional spline functions to achieve smoother solutions in three dimensions by post-processing, new three-dimensional elements for C1 basis functions, and a program to assist in the design of elements with higher continuity; and (7) a development of ellipsoidal harmonics and Lame's equation, with generalization to any dimension and a demonstration that Cartesian, cylindrical, spherical, spheroidal, and sphero-conical harmonics are all limiting cases. The report includes a description of the Finite Difference, Finite Volume, and domain remapping

  16. A Two Layers Novel Low-Cost and Optimized Embedded Board Based on TMS320C6713 DSP and Spartan-3 FPGA

    Directory of Open Access Journals (Sweden)

    Bahram Rashidi

    2013-05-01

    Full Text Available This paper presents the design and implementation of a new low-cost and minimum embedded board based on TMS320C6713 (PYP 208-PIN (PQFP DSP and Spartan-3 (XCS400-4PQG208C FPGA in two layers with mount elements on two sides of the board. The proposed embedded board was developed satisfactorily for different applications such as data acquisition of sensor’s with serial port, control units, finite state machines, signal processing algorithms, navigation computing, Kalman filtering etc. Goal of the design was to implement as many as possible low-cost and minimum sizes of the board, also to receive input signals in a short time period and as real time. The board features are include: mount elements in two side of the board for minimization of the proposed board and also placed decoupling capacitors (by pass for the DSP and FPGA in bottom layer of board strictly below these two ICs because should be placed as close as possible to the power supply pins DSP and FPGA, GND polygon layer is used in total top layer and microcomputer ground for DSP & FPGA in bottom layer, use FPGA for two aim ones for implementation of glue logic total of board and interface between serial connectors, use three RS-232 serial port, one RS-422, and SPI serial port on FPGA, use MT48LC16M16A SDRAM-256MB(4*4MB*16, Am29LV400B Flash memory 4 Megabit (512 K x 8-Bit/256 K x 16-Bit and XCF02S configuration PROM. The size of the proposed embedded board is 11.1cm*17. 7cm so this board is optimized of aspect cost, performance, power, weight, and size.

  17. A Study of Electrical Motors Controlling Optimization Methods

    Directory of Open Access Journals (Sweden)

    Saeid Fatemi

    2013-11-01

    Full Text Available In order to design an efficient motor cooling system, it is important to accurately predict the power optimization which is normally dissipated in form of heat. This study presents an analytical method for estimating bearing frictional optimization and numerical method for estimating electromagnetic optimization for an electric vehicle electrical motor. The power optimization obtained use heat sources when evaluating the thermal performance of the motor. The results showed that electromagnetic optimization are dominant and contributed over 80% of all optimization, while bearing optimization contributes about 2% of the total electric motor. The results also showed that bearing optimization increase significantly with increasing speed or load.

  18. On Best Practice Optimization Methods in R

    Directory of Open Access Journals (Sweden)

    John C. Nash

    2014-09-01

    Full Text Available R (R Core Team 2014 provides a powerful and flexible system for statistical computations. It has a default-install set of functionality that can be expanded by the use of several thousand add-in packages as well as user-written scripts. While R is itself a programming language, it has proven relatively easy to incorporate programs in other languages, particularly Fortran and C. Success, however, can lead to its own costs: • Users face a confusion of choice when trying to select packages in approaching a problem. • A need to maintain workable examples using early methods may mean some tools offered as a default may be dated. • In an open-source project like R, how to decide what tools offer "best practice" choices, and how to implement such a policy, present a serious challenge. We discuss these issues with reference to the tools in R for nonlinear parameter estimation (NLPE and optimization, though for the present article `optimization` will be limited to function minimization of essentially smooth functions with at most bounds constraints on the parameters. We will abbreviate this class of problems as NLPE. We believe that the concepts proposed are transferable to other classes of problems seen by R users.

  19. A Self-Adjusting Method to Resist Bus Bunching Based on Boarding Limits

    Directory of Open Access Journals (Sweden)

    Shuzhi Zhao

    2016-01-01

    Full Text Available Bus bunching is one of the most serious problems of urban bus systems. Bus bunching increases waiting and travel time of passengers. Many bus systems use schedules to reach equal headways. Compared to the idea of schedules and the target headway introduced later, we propose a new method to improve the efficiency of a bus system and avoid bus bunching by boarding limits. Our solution can be effectively implemented when buses cannot travel as planned because of bad road conditions and dynamic demands at bus stops. Besides, using our method, bus headways reach the state with equal headways dynamically and spontaneously without drivers’ explicit intervention. Moreover, the method can improve the level of the bus service and reduce total travel time of passengers. We verify our method using an ideal bus route and a real bus route, both showing the success of the proposed method.

  20. Optimization of Binder Jetting Using Taguchi Method

    Science.gov (United States)

    Shrestha, Sanjay; Manogharan, Guha

    2017-03-01

    Among several additive manufacturing (AM) methods, binder-jetting has undergone a recent advancement in its ability to process metal powders through selective deposition of binders on a powder bed followed by curing, sintering, and infiltration. This study analyzes the impact of various process parameters in binder jetting on mechanical properties of sintered AM metal parts. The Taguchi optimization method has been employed to determine the optimum AM parameters to improve transverse rupture strength (TRS), specifically: binder saturation, layer thickness, roll speed, and feed-to-powder ratio. The effects of the selected process parameters on the TRS performance of sintered SS 316L samples are studied with the American Society of Testing Materials (ASTM) standard test method. It was found that binder saturation and feed-to-powder ratio were the most critical parameters, which reflects the strong influence of binder powder interaction and density of powder bed on resulting mechanical properties. This article serves as an aid in understanding the optimum process parameters for binder jetting of SS 316L.

  1. Optimization of Binder Jetting Using Taguchi Method

    Science.gov (United States)

    Shrestha, Sanjay; Manogharan, Guha

    2017-01-01

    Among several additive manufacturing (AM) methods, binder-jetting has undergone a recent advancement in its ability to process metal powders through selective deposition of binders on a powder bed followed by curing, sintering, and infiltration. This study analyzes the impact of various process parameters in binder jetting on mechanical properties of sintered AM metal parts. The Taguchi optimization method has been employed to determine the optimum AM parameters to improve transverse rupture strength (TRS), specifically: binder saturation, layer thickness, roll speed, and feed-to-powder ratio. The effects of the selected process parameters on the TRS performance of sintered SS 316L samples are studied with the American Society of Testing Materials (ASTM) standard test method. It was found that binder saturation and feed-to-powder ratio were the most critical parameters, which reflects the strong influence of binder powder interaction and density of powder bed on resulting mechanical properties. This article serves as an aid in understanding the optimum process parameters for binder jetting of SS 316L.

  2. DETERMINATION METHOD OF OPTIMAL SUPPORTING TIME IN HEADING FACE

    Institute of Scientific and Technical Information of China (English)

    杜长龙; 曹红波; 王燕宁; 张艳

    1997-01-01

    This paper has put forward a concept of optimal supporting time through analysing the influence of the supporting time in the heading face on the supporting result of surrounding rock. The method of the optimal supporting time determined by graphical method is discussed, and the calculating formula for determining the optimal supporting time through the analysis method is derived.

  3. A LEVEL-VALUE ESTIMATION METHOD FOR SOLVING GLOBAL OPTIMIZATION

    Institute of Scientific and Technical Information of China (English)

    WU Dong-hua; YU Wu-yang; TIAN Wei-wen; ZHANG Lian-sheng

    2006-01-01

    A level-value estimation method was illustrated for solving the constrained global optimization problem. The equivalence between the root of a modified variance equation and the optimal value of the original optimization problem is shown. An alternate algorithm based on the Newton's method is presented and the convergence of its implementable approach is proved. Preliminary numerical results indicate that the method is effective.

  4. Design optimization method for Francis turbine

    Science.gov (United States)

    Kawajiri, H.; Enomoto, Y.; Kurosawa, S.

    2014-03-01

    This paper presents a design optimization system coupled CFD. Optimization algorithm of the system employs particle swarm optimization (PSO). Blade shape design is carried out in one kind of NURBS curve defined by a series of control points. The system was applied for designing the stationary vanes and the runner of higher specific speed francis turbine. As the first step, single objective optimization was performed on stay vane profile, and second step was multi-objective optimization for runner in wide operating range. As a result, it was confirmed that the design system is useful for developing of hydro turbine.

  5. UNDERSTANDING OF FUZZY OPTIMIZATION:THEORIES AND METHODS

    Institute of Scientific and Technical Information of China (English)

    TANG Jiafu; WANG Dingwei; Richard Y K FUNG; Kai-Leung Yung

    2004-01-01

    A brief summary on and comprehensive understanding of fuzzy optimizationis presentedThis summary is made on aspects of fuzzy modelling and fuzzy optimization,classification and formulation for the fuzzy optimization problems, models and methods.The importance of interpretation of the problem and formulation of the optimal solutionin fuzzy sense are emphasized in the summary of the fuzzy optimization.

  6. Numerical methods and optimization a consumer guide

    CERN Document Server

    Walter, Éric

    2014-01-01

    Initial training in pure and applied sciences tends to present problem-solving as the process of elaborating explicit closed-form solutions from basic principles, and then using these solutions in numerical applications. This approach is only applicable to very limited classes of problems that are simple enough for such closed-form solutions to exist. Unfortunately, most real-life problems are too complex to be amenable to this type of treatment. Numerical Methods and Optimization – A Consumer Guide presents methods for dealing with them. Shifting the paradigm from formal calculus to numerical computation, the text makes it possible for the reader to ·         discover how to escape the dictatorship of those particular cases that are simple enough to receive a closed-form solution, and thus gain the ability to solve complex, real-life problems; ·         understand the principles behind recognized algorithms used in state-of-the-art numerical software; ·         learn the advantag...

  7. On stochastic and discontinuous optimization methods

    Energy Technology Data Exchange (ETDEWEB)

    Ermoliev, Y.

    1994-12-31

    The talk is based on a joint article by Y. Ermoliev, V. Norkin and R. Wets. A new notion of subgradient is introduced which allows to develop easily implementable procedures of discontinuous optimization, in particular, finite-difference approximation schemes. The approach relies on the notion of differentiability in the sense of distributions converting a discontinuous optimization problem into a problem of the stochastic optimization. Applications involving risks and abrupt transitions are discussed.

  8. Design Optimization of Printed Circuit Board Embedded Inductors through Genetic Algorithms with Verification by COMSOL

    DEFF Research Database (Denmark)

    Madsen, Mickey Pierre; Mønster, Jakob Døllner; Knott, Arnold

    2013-01-01

    This paper describes the implementation of a complete design tool for design, analysis, optimization and production of PCB embedded inductors. The papers shows how the LiveLink between MATLAB and COMSOL makes it possible to combine the scripting and calculation power of MATLAB with the simulation....... This is not possible for the solenoid and toroid, hence complete 3D structure has been made and simulated for these structures....

  9. Optimization: NURBS and the quasi-Newton method

    Science.gov (United States)

    Coburn, Todd Dale

    Optimization is important in both engineering and mathematics. The Quasi-Newton Method is widely used for optimization due to its speed and efficiency. NonUniform Rational B-Splines (NURBS) are piecewise parametric approximations to curves and surfaces. NURBS have great curve-fitting properties that can be applied to improve optimization performance. This dissertation investigated the use of NURBS in optimization, focusing primarily on the coupling of NURBS with the Quasi-Newton Method. A hybrid optimization procedure dubbed the NURBS-Quasi-Newton (NQN) Method was developed and utilized that can virtually assure that the global minimum will be found. A Method was also developed to implement Pure NURBS Optimization (PNO), which can be used to optimize non-continuous and singular functions as well as functions of point cloud data. It was concluded that NURBS offer significant benefits for optimization, both individually and coupled with Quasi-Newton Methods.

  10. Research on dynamic model of printed circuit board based on finite element method

    Science.gov (United States)

    Wei, Hui; Xu, Liangjun

    2017-08-01

    The vibration characteristics of printed circuit boards are related to the reliability of electronic components installed on their surface. Finite element software is a powerful tool to analyze the vibration characteristics of printed circuit boards, and the correct establishment of finite element model is very important. In this paper, the dynamic model of anisotropic printed circuit board is established by analyzing the material properties of printed circuit board. The influence of boundary condition and lumped mass on the vibration characteristics of printed circuit board is analyzed. In order to establish a more realistic printed circuit The finite element model of the plate provides the necessary basis.

  11. Mathematical programming methods for large-scale topology optimization problems

    DEFF Research Database (Denmark)

    Rojas Labanda, Susana

    , and at the same time, reduce the number of function evaluations. Nonlinear optimization methods, such as sequential quadratic programming and interior point solvers, have almost not been embraced by the topology optimization community. Thus, this work is focused on the introduction of this kind of second......This thesis investigates new optimization methods for structural topology optimization problems. The aim of topology optimization is finding the optimal design of a structure. The physical problem is modelled as a nonlinear optimization problem. This powerful tool was initially developed...... for the classical minimum compliance problem. Two of the state-of-the-art optimization algorithms are investigated and implemented for this structural topology optimization problem. A Sequential Quadratic Programming (TopSQP) and an interior point method (TopIP) are developed exploiting the specific mathematical...

  12. Adjoint Optimization of a Wing Using the CSRT Method

    NARCIS (Netherlands)

    Straathof, M.H.; Van Tooren, M.J.L.

    2011-01-01

    This paper will demonstrate the potential of the Class-Shape-Refinement-Transformation (CSRT) method for aerodynamically optimizing three-dimensional surfaces. The CSRT method was coupled to an in-house Euler solver and this combination was used in an optimization framework to optimize the ONERA M6

  13. A Review of Deterministic Optimization Methods in Engineering and Management

    Directory of Open Access Journals (Sweden)

    Ming-Hua Lin

    2012-01-01

    Full Text Available With the increasing reliance on modeling optimization problems in practical applications, a number of theoretical and algorithmic contributions of optimization have been proposed. The approaches developed for treating optimization problems can be classified into deterministic and heuristic. This paper aims to introduce recent advances in deterministic methods for solving signomial programming problems and mixed-integer nonlinear programming problems. A number of important applications in engineering and management are also reviewed to reveal the usefulness of the optimization methods.

  14. A Study of Electrical Motors Controlling Optimization Methods

    OpenAIRE

    Saeid Fatemi

    2013-01-01

    In order to design an efficient motor cooling system, it is important to accurately predict the power optimization which is normally dissipated in form of heat. This study presents an analytical method for estimating bearing frictional optimization and numerical method for estimating electromagnetic optimization for an electric vehicle electrical motor. The power optimization obtained use heat sources when evaluating the thermal performance of the motor. The results showed that electromagneti...

  15. Computational Methods for Design, Control and Optimization

    Science.gov (United States)

    2007-10-01

    34scenario" that applies to channel flows ( Poiseuille flows , Couette flow ) and pipe flows . Over the past 75 years many complex "transition theories" have...other areas of flow control, optimization and aerodynamic design. approximate sensitivity calculations and optimization codes. The effort was built on a...for fluid flow problems. The improved robustness and computational efficiency of this approach makes it practical for a wide class of problems. The

  16. A simple method to optimize HMC performance

    CERN Document Server

    Bussone, Andrea; Drach, Vincent; Hansen, Martin; Hietanen, Ari; Rantaharju, Jarno; Pica, Claudio

    2016-01-01

    We present a practical strategy to optimize a set of Hybrid Monte Carlo parameters in simulations of QCD and QCD-like theories. We specialize to the case of mass-preconditioning, with multiple time-step Omelyan integrators. Starting from properties of the shadow Hamiltonian we show how the optimal setup for the integrator can be chosen once the forces and their variances are measured, assuming that those only depend on the mass-preconditioning parameter.

  17. An Efficient Method for Reliability-based Multidisciplinary Design Optimization

    Institute of Scientific and Technical Information of China (English)

    Fan Hui; Li Weiji

    2008-01-01

    Design for modem engineering system is becoming multidisciplinary and incorporates practical uncertainties; therefore, it is necessary to synthesize reliability analysis and the multidiscipLinary design optimization (MDO) techniques for the design of complex engineering system. An advanced first order second moment method-based concurrent subspace optimization approach is proposed based on the comparison and analysis of the existing multidisciplinary optimization techniques and the reliability analysis methods. It is seen through a canard configuration optimization for a three-surface transport that the proposed method is computationally efficient and practical with the least modification to the current deterministic optimization process.

  18. Method of Enhancing On-Board State Estimation Using Communication Signals

    Science.gov (United States)

    Anzalone, Evan J. (Inventor); Chuang, Jason C. H. (Inventor)

    2015-01-01

    A method of enhancing on-board state estimation for a spacecraft utilizes a network of assets to include planetary-based assets and space-based assets. Communication signals transmitted from each of the assets into space are defined by a common protocol. Data is embedded in each communication signal transmitted by the assets. The data includes a time-of-transmission for a corresponding one of the communication signals and a position of a corresponding one of the assets at the time-of-transmission. A spacecraft is equipped to receive the communication signals, has a clock synchronized to the space-wide time reference frame, and has a processor programmed to generate state estimates of the spacecraft. Using its processor, the spacecraft determines a one-dimensional range from itself to at least one of the assets and then updates its state estimates using each one-dimensional range.

  19. An optimization method for metamorphic mechanisms based on multidisciplinary design optimization

    Directory of Open Access Journals (Sweden)

    Zhang Wuxiang

    2014-12-01

    Full Text Available The optimization of metamorphic mechanisms is different from that of the conventional mechanisms for its characteristics of multi-configuration. There exist complex coupled design variables and constraints in its multiple different configuration optimization models. To achieve the compatible optimized results of these coupled design variables, an optimization method for metamorphic mechanisms is developed in the paper based on the principle of multidisciplinary design optimization (MDO. Firstly, the optimization characteristics of the metamorphic mechanism are summarized distinctly by proposing the classification of design variables and constraints as well as coupling interactions among its different configuration optimization models. Further, collaborative optimization technique which is used in MDO is adopted for achieving the overall optimization performance. The whole optimization process is then proposed by constructing a two-level hierarchical scheme with global optimizer and configuration optimizer loops. The method is demonstrated by optimizing a planar five-bar metamorphic mechanism which has two configurations, and results show that it can achieve coordinated optimization results for the same parameters in different configuration optimization models.

  20. An optimization method for metamorphic mechanisms based on multidisciplinary design optimization

    Institute of Scientific and Technical Information of China (English)

    Zhang Wuxiang; Wu Teng; Ding Xilun

    2014-01-01

    The optimization of metamorphic mechanisms is different from that of the conventional mechanisms for its characteristics of multi-configuration. There exist complex coupled design vari-ables and constraints in its multiple different configuration optimization models. To achieve the compatible optimized results of these coupled design variables, an optimization method for meta-morphic mechanisms is developed in the paper based on the principle of multidisciplinary design optimization (MDO). Firstly, the optimization characteristics of the metamorphic mechanism are summarized distinctly by proposing the classification of design variables and constraints as well as coupling interactions among its different configuration optimization models. Further, collabora-tive optimization technique which is used in MDO is adopted for achieving the overall optimization performance. The whole optimization process is then proposed by constructing a two-level hierar-chical scheme with global optimizer and configuration optimizer loops. The method is demon-strated by optimizing a planar five-bar metamorphic mechanism which has two configurations, and results show that it can achieve coordinated optimization results for the same parameters in different configuration optimization models.

  1. Apparatus And Method Of Using Flexible Printed Circuit Board In Optical Transceiver Device

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Gene R. (Albuquerque, NM); Armendariz, Marcelino G. (Albuquerque, NM); Bryan, Robert P. (Albuquerque, NM); Carson, Richard F. (Albuquerque, NM); Duckett, III, Edwin B. (Albuquerque, NM); McCormick, Frederick B. (Albuquerque, NM); Peterson, David W. (Sandia Park, NM); Peterson, Gary D. (Albuquerque, NM); Reysen, Bill H. (Lafayette, CO)

    2005-03-15

    This invention relates to a flexible printed circuit board that is used in connection with an optical transmitter, receiver or transceiver module. In one embodiment, the flexible printed circuit board has flexible metal layers in between flexible insulating layers, and the circuit board comprises: (1) a main body region orientated in a first direction having at least one electrical or optoelectronic device; (2) a plurality of electrical contact pads integrated into the main body region, where the electrical contact pads function to connect the flexible printed circuit board to an external environment; (3) a buckle region extending from one end of the main body region; and (4) a head region extending from one end of the buckle region, and where the head region is orientated so that it is at an angle relative to the direction of the main body region. The electrical contact pads may be ball grid arrays, solder balls or land-grid arrays, and they function to connect the circuit board to an external environment. A driver or amplifier chip may be adapted to the head region of the flexible printed circuit board. In another embodiment, a heat spreader passes along a surface of the head region of the flexible printed circuit board, and a window is formed in the head region of the flexible printed circuit board. Optoelectronic devices are adapted to the head spreader in such a manner that they are accessible through the window in the flexible printed circuit board.

  2. Design Methods and Optimization for Morphing Aircraft

    Science.gov (United States)

    Crossley, William A.

    2005-01-01

    This report provides a summary of accomplishments made during this research effort. The major accomplishments are in three areas. The first is the use of a multiobjective optimization strategy to help identify potential morphing features that uses an existing aircraft sizing code to predict the weight, size and performance of several fixed-geometry aircraft that are Pareto-optimal based upon on two competing aircraft performance objectives. The second area has been titled morphing as an independent variable and formulates the sizing of a morphing aircraft as an optimization problem in which the amount of geometric morphing for various aircraft parameters are included as design variables. This second effort consumed most of the overall effort on the project. The third area involved a more detailed sizing study of a commercial transport aircraft that would incorporate a morphing wing to possibly enable transatlantic point-to-point passenger service.

  3. Multimodel methods for optimal control of aeroacoustics.

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Guoquan (Rice University, Houston, TX); Collis, Samuel Scott

    2005-01-01

    A new multidomain/multiphysics computational framework for optimal control of aeroacoustic noise has been developed based on a near-field compressible Navier-Stokes solver coupled with a far-field linearized Euler solver both based on a discontinuous Galerkin formulation. In this approach, the coupling of near- and far-field domains is achieved by weakly enforcing continuity of normal fluxes across a coupling surface that encloses all nonlinearities and noise sources. For optimal control, gradient information is obtained by the solution of an appropriate adjoint problem that involves the propagation of adjoint information from the far-field to the near-field. This computational framework has been successfully applied to study optimal boundary-control of blade-vortex interaction, which is a significant noise source for helicopters on approach to landing. In the model-problem presented here, the noise propagated toward the ground is reduced by 12dB.

  4. A Method for Determining Optimal Residential Energy Efficiency Packages

    Energy Technology Data Exchange (ETDEWEB)

    Polly, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Gestwick, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bianchi, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Anderson, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Horowitz, S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Christensen, C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Judkoff, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2011-04-01

    This report describes an analysis method for determining optimal residential energy efficiency retrofit packages and, as an illustrative example, applies the analysis method to a 1960s-era home in eight U.S. cities covering a range of International Energy Conservation Code (IECC) climate regions. The method uses an optimization scheme that considers average energy use (determined from building energy simulations) and equivalent annual cost to recommend optimal retrofit packages specific to the building, occupants, and location.

  5. Advanced Topology Optimization Methods for Conceptual Architectural Design

    DEFF Research Database (Denmark)

    Aage, Niels; Amir, Oded; Clausen, Anders

    2014-01-01

    This paper presents a series of new, advanced topology optimization methods, developed specifically for conceptual architectural design of structures. The proposed computational procedures are implemented as components in the framework of a Grasshopper plugin, providing novel capacities...... in topological optimization: Interactive control and continuous visualization; embedding flexible voids within the design space; consideration of distinct tension / compression properties; and optimization of dual material systems. In extension, optimization procedures for skeletal structures such as trusses...... and frames are implemented. The developed procedures allow for the exploration of new territories in optimization of architectural structures, and offer new methodological strategies for bridging conceptual gaps between optimization and architectural practice....

  6. A novel reutilization method for waste printed circuit boards as flame retardant and smoke suppressant for poly (vinyl chloride).

    Science.gov (United States)

    Xiu, Fu-Rong; Weng, Huiwei; Qi, Yingying; Yu, Gending; Zhang, Zhigang; Zhang, Fu-Shen

    2016-09-05

    In this study, a novel reutilization method for waste printed circuit boards (PCBs) as flame retardant and smoke suppressant for poly (vinyl chloride) (PVC) was successfully testified. A supercritical water oxidation (SCWO) process was applied to treat waste PCBs before they could be used as flame retardants of PVC. The results indicated that SCWO conditions had a significant effect on the flame retarding and smoke suppressing properties of waste PCBs for PVC. Cu2O, CuO, and SnO2 were the main active ingredients in waste PCBs-derived flame retardants. A conversion of Cu elements (Cu(0)→Cu(+)→Cu(2+)) during SCWO process with the increase of reaction temperature was found to be the key influence factor for the flame retarding properties of SCWO-treated PCBs. The experiment results also showed that there was a synergistic effect of flame retardancy between Cu(+) and Cu(2+). After the optimized SCWO treatment, SCWO-treated PCBs significantly improved the flame retardancy and smoke suppression of PVC. Limiting oxygen index (LOI) and char yield (CY) increased with increasing SCWO-treated PCBs content in PVC, while smoke density rating (SDR) and maximum smoke density (MSD) decreased markedly. The mechanical properties of PVC samples were influenced in different degree by adding different content SCWO-treated PCBs.

  7. COMPARISON OF NONLINEAR DYNAMICS OPTIMIZATION METHODS FOR APS-U

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Y.; Borland, Michael

    2017-06-25

    Many different objectives and genetic algorithms have been proposed for storage ring nonlinear dynamics performance optimization. These optimization objectives include nonlinear chromaticities and driving/detuning terms, on-momentum and off-momentum dynamic acceptance, chromatic detuning, local momentum acceptance, variation of transverse invariant, Touschek lifetime, etc. In this paper, the effectiveness of several different optimization methods and objectives are compared for the nonlinear beam dynamics optimization of the Advanced Photon Source upgrade (APS-U) lattice. The optimized solutions from these different methods are preliminarily compared in terms of the dynamic acceptance, local momentum acceptance, chromatic detuning, and other performance measures.

  8. METHOD FOR OPTIMIZING THE ENERGY OF PUMPS

    NARCIS (Netherlands)

    Skovmose Kallesøe, Carsten; De Persis, Claudio

    2013-01-01

    The device for energy-optimization on operation of several centrifugal pumps controlled in rotational speed, in a hydraulic installation, begins firstly with determining which pumps as pilot pumps are assigned directly to a consumer and which pumps are hydraulically connected in series upstream of t

  9. Logic-based methods for optimization combining optimization and constraint satisfaction

    CERN Document Server

    Hooker, John

    2011-01-01

    A pioneering look at the fundamental role of logic in optimization and constraint satisfaction While recent efforts to combine optimization and constraint satisfaction have received considerable attention, little has been said about using logic in optimization as the key to unifying the two fields. Logic-Based Methods for Optimization develops for the first time a comprehensive conceptual framework for integrating optimization and constraint satisfaction, then goes a step further and shows how extending logical inference to optimization allows for more powerful as well as flexible

  10. Global Optimization methods for Gravitational Lens Systems with Regularized Sources

    CERN Document Server

    Rogers, Adam

    2012-01-01

    Several approaches exist to model gravitational lens systems. In this study, we apply global optimization methods to find the optimal set of lens parameters using a genetic algorithm. We treat the full optimization procedure as a two-step process: an analytical description of the source plane intensity distribution is used to find an initial approximation to the optimal lens parameters. The second stage of the optimization uses a pixelated source plane with the semilinear method to determine an optimal source. Regularization is handled by means of an iterative method and the generalized cross validation (GCV) and unbiased predictive risk estimator (UPRE) functions that are commonly used in standard image deconvolution problems. This approach simultaneously estimates the optimal regularization parameter and the number of degrees of freedom in the source. Using the GCV and UPRE functions we are able to justify an estimation of the number of source degrees of freedom found in previous work. We test our approach ...

  11. The estimation of the pollutant emissions on-board vessels by means of numerical methods

    Science.gov (United States)

    Jenaru, A.; Arsenie, P.; Hanzu-Pazara, R.

    2016-08-01

    Protection of the environment, especially within the most recent years, has become a constant problem considered by the states and the governments of the world, which are more and more concerned about the serious problems caused by the continuous deterioration of the environment. The long term effects of pollution on the environment generated by the lack of penalty regulations, have directed the attention of statesmen upon the necessity of the elaboration of normative acts meant to be effective in the continuous fight with it. Maritime transportation generates approximately 4% of the total of the CO2 emissions produced by human activities. This paper is intended to present two methods of estimation of the gases emissions on-board a vessel, methods that are very useful for the crews which are exploiting them. For the determination and the validation of these methods we are going to use the determinations from the tank ship. This ship has as a main propulsion engine Wärtsilä DU Sulzer RT Flex 50 - 6 cylinders that develops a maximal power of 9720 kW and has a permanent monitoring system of the pollutant emissions. The methods we develop here are using the values of the polluting elements from the exhaust gases that are determined at the exit of the vessel from the ship yard, in the framework of the acceptance tests. These values have been introduced within the framework of a matrix in the MATHCAD program. This matrix represents the starting point of the two mentioned methods: the analytical method and the graphical method. During the study we are going to evaluate the development and validation of an analytical tool to be used to determine the standard of emissions aimed at thermal machines on ships. One of the main objectives of this article represents an objective assessment of the expediency of using non-fuels for internal combustion engines in vessels.

  12. Numerical methods of mathematical optimization with Algol and Fortran programs

    CERN Document Server

    Künzi, Hans P; Zehnder, C A; Rheinboldt, Werner

    1971-01-01

    Numerical Methods of Mathematical Optimization: With ALGOL and FORTRAN Programs reviews the theory and the practical application of the numerical methods of mathematical optimization. An ALGOL and a FORTRAN program was developed for each one of the algorithms described in the theoretical section. This should result in easy access to the application of the different optimization methods.Comprised of four chapters, this volume begins with a discussion on the theory of linear and nonlinear optimization, with the main stress on an easily understood, mathematically precise presentation. In addition

  13. Review of dynamic optimization methods in renewable natural resource management

    Science.gov (United States)

    Williams, B.K.

    1989-01-01

    In recent years, the applications of dynamic optimization procedures in natural resource management have proliferated. A systematic review of these applications is given in terms of a number of optimization methodologies and natural resource systems. The applicability of the methods to renewable natural resource systems are compared in terms of system complexity, system size, and precision of the optimal solutions. Recommendations are made concerning the appropriate methods for certain kinds of biological resource problems.

  14. Study on optimization control method based on artificial neural network

    Institute of Scientific and Technical Information of China (English)

    FU Hua; SUN Shao-guang; XU Zhen-Iiang

    2005-01-01

    In the goal optimization and control optimization process the problems with common artificial neural network algorithm are unsure convergence, insufficient post-training network precision, and slow training speed, in which partial minimum value question tends to occur. This paper conducted an in-depth study on the causes of the limitations of the algorithm, presented a rapid artificial neural network algorithm, which is characterized by integrating multiple algorithms and by using their complementary advantages. The salient feature of the method is self-organization, which can effectively prevent the optimized results from tending to be partial minimum values. Overall optimization can be achieved with this method, goal function can be searched for in overall scope. With optimization control of coal mine ventilator as a practical application, the paper proves that by integrating multiple artificial neural network algorithms, best control optimization and goal optimized can be achieved.

  15. Optimization and control methods in industrial engineering and construction

    CERN Document Server

    Wang, Xiangyu

    2014-01-01

    This book presents recent advances in optimization and control methods with applications to industrial engineering and construction management. It consists of 15 chapters authored by recognized experts in a variety of fields including control and operation research, industrial engineering, and project management. Topics include numerical methods in unconstrained optimization, robust optimal control problems, set splitting problems, optimum confidence interval analysis, a monitoring networks optimization survey, distributed fault detection, nonferrous industrial optimization approaches, neural networks in traffic flows, economic scheduling of CCHP systems, a project scheduling optimization survey, lean and agile construction project management, practical construction projects in Hong Kong, dynamic project management, production control in PC4P, and target contracts optimization.   The book offers a valuable reference work for scientists, engineers, researchers and practitioners in industrial engineering and c...

  16. DYNAMIC OPTIMIZATION FOR UNCERTAIN STRUCTURES USING INTERVAL METHOD

    Institute of Scientific and Technical Information of China (English)

    ChertSub-A-; WuJie; LiuChun

    2003-01-01

    An interval optimization method for the dynamic response of structures with interval parameters is presented. The matrices of structures with interval parameters are given. Combining the interval extension with the perturbation, the method for interval dynamic response analysis is derived. The interval optimization problem is transformed into a corresponding deterministic one. Because the mean values and the uncertainties of the interval parameters can be elected design variables, more information of the optimization results can be obtained by the present method than that obtained by the deterministic one. The present method is implemented for a truss structure. The numerical results show that the method is effective.

  17. An uncertain multidisciplinary design optimization method using interval convex models

    Science.gov (United States)

    Li, Fangyi; Luo, Zhen; Sun, Guangyong; Zhang, Nong

    2013-06-01

    This article proposes an uncertain multi-objective multidisciplinary design optimization methodology, which employs the interval model to represent the uncertainties of uncertain-but-bounded parameters. The interval number programming method is applied to transform each uncertain objective function into two deterministic objective functions, and a satisfaction degree of intervals is used to convert both the uncertain inequality and equality constraints to deterministic inequality constraints. In doing so, an unconstrained deterministic optimization problem will be constructed in association with the penalty function method. The design will be finally formulated as a nested three-loop optimization, a class of highly challenging problems in the area of engineering design optimization. An advanced hierarchical optimization scheme is developed to solve the proposed optimization problem based on the multidisciplinary feasible strategy, which is a well-studied method able to reduce the dimensions of multidisciplinary design optimization problems by using the design variables as independent optimization variables. In the hierarchical optimization system, the non-dominated sorting genetic algorithm II, sequential quadratic programming method and Gauss-Seidel iterative approach are applied to the outer, middle and inner loops of the optimization problem, respectively. Typical numerical examples are used to demonstrate the effectiveness of the proposed methodology.

  18. Gradient-based methods for production optimization of oil reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Suwartadi, Eka

    2012-07-01

    Production optimization for water flooding in the secondary phase of oil recovery is the main topic in this thesis. The emphasis has been on numerical optimization algorithms, tested on case examples using simple hypothetical oil reservoirs. Gradientbased optimization, which utilizes adjoint-based gradient computation, is used to solve the optimization problems. The first contribution of this thesis is to address output constraint problems. These kinds of constraints are natural in production optimization. Limiting total water production and water cut at producer wells are examples of such constraints. To maintain the feasibility of an optimization solution, a Lagrangian barrier method is proposed to handle the output constraints. This method incorporates the output constraints into the objective function, thus avoiding additional computations for the constraints gradient (Jacobian) which may be detrimental to the efficiency of the adjoint method. The second contribution is the study of the use of second-order adjoint-gradient information for production optimization. In order to speedup convergence rate in the optimization, one usually uses quasi-Newton approaches such as BFGS and SR1 methods. These methods compute an approximation of the inverse of the Hessian matrix given the first-order gradient from the adjoint method. The methods may not give significant speedup if the Hessian is ill-conditioned. We have developed and implemented the Hessian matrix computation using the adjoint method. Due to high computational cost of the Newton method itself, we instead compute the Hessian-timesvector product which is used in a conjugate gradient algorithm. Finally, the last contribution of this thesis is on surrogate optimization for water flooding in the presence of the output constraints. Two kinds of model order reduction techniques are applied to build surrogate models. These are proper orthogonal decomposition (POD) and the discrete empirical interpolation method (DEIM

  19. Mixed methods for viscoelastodynamics and topology optimization

    Directory of Open Access Journals (Sweden)

    Giacomo Maurelli

    2014-07-01

    Full Text Available A truly-mixed approach for the analysis of viscoelastic structures and continua is presented. An additive decomposition of the stress state into a viscoelastic part and a purely elastic one is introduced along with an Hellinger-Reissner variational principle wherein the stress represents the main variable of the formulation whereas the kinematic descriptor (that in the case at hand is the velocity field acts as Lagrange multiplier. The resulting problem is a Differential Algebraic Equation (DAE because of the need to introduce static Lagrange multipliers to comply with the Cauchy boundary condition on the stress. The associated eigenvalue problem is known in the literature as constrained eigenvalue problem and poses several difficulties for its solution that are addressed in the paper. The second part of the paper proposes a topology optimization approach for the rationale design of viscoelastic structures and continua. Details concerning density interpolation, compliance problems and eigenvalue-based objectives are given. Worked numerical examples are presented concerning both the dynamic analysis of viscoelastic structures and their topology optimization.

  20. Optimizing the Post Sandvik Nanoflex material model using inverse optimization and the finite element method

    NARCIS (Netherlands)

    Amstel, van T.; Groen, M.; Post, J.; Huetink, J.

    2005-01-01

    This article describes an inverse optimization method for the Sandvik Nanoflex steel in cold forming processes. The optimization revolves around measured samples and calculations using the Finite Element Method. Sandvik Nanoflex is part of the group of meta-stable stainless steels. These materials a

  1. SOURCES OF COPPER IONS AND SELECTED METHODS OF THEIR REMOVAL FROM WASTEWATER FROM THE PRINTED CIRCUITS BOARD PRODUCTION

    Directory of Open Access Journals (Sweden)

    Maciej Thomas

    2014-10-01

    Full Text Available This paper presents the issues related to the presence and removal of copper compounds from industrial effluents with including wastewater from plants involved in the production of printed circuit boards. Characterized the toxicological properties of selected copper compounds, described the applicable technological processes, sources of copper ions in the effluents and selected methods for their removal.

  2. Present-day Problems and Methods of Optimization in Mechatronics

    Directory of Open Access Journals (Sweden)

    Tarnowski Wojciech

    2017-06-01

    Full Text Available It is justified that design is an inverse problem, and the optimization is a paradigm. Classes of design problems are proposed and typical obstacles are recognized. Peculiarities of the mechatronic designing are specified as a proof of a particle importance of optimization in the mechatronic design. Two main obstacles of optimization are discussed: a complexity of mathematical models and an uncertainty of the value system, in concrete case. Then a set of non-standard approaches and methods are presented and discussed, illustrated by examples: a fuzzy description, a constraint-based iterative optimization, AHP ranking method and a few MADM functions in Matlab.

  3. Computation of Optimal Monotonicity Preserving General Linear Methods

    KAUST Repository

    Ketcheson, David I.

    2009-07-01

    Monotonicity preserving numerical methods for ordinary differential equations prevent the growth of propagated errors and preserve convex boundedness properties of the solution. We formulate the problem of finding optimal monotonicity preserving general linear methods for linear autonomous equations, and propose an efficient algorithm for its solution. This algorithm reliably finds optimal methods even among classes involving very high order accuracy and that use many steps and/or stages. The optimality of some recently proposed methods is verified, and many more efficient methods are found. We use similar algorithms to find optimal strong stability preserving linear multistep methods of both explicit and implicit type, including methods for hyperbolic PDEs that use downwind-biased operators.

  4. Tabu search method with random moves for globally optimal design

    Science.gov (United States)

    Hu, Nanfang

    1992-09-01

    Optimum engineering design problems are usually formulated as non-convex optimization problems of continuous variables. Because of the absence of convexity structure, they can have multiple minima, and global optimization becomes difficult. Traditional methods of optimization, such as penalty methods, can often be trapped at a local optimum. The tabu search method with random moves to solve approximately these problems is introduced. Its reliability and efficiency are examined with the help of standard test functions. By the analysis of the implementations, it is seen that this method is easy to use, and no derivative information is necessary. It outperforms the random search method and composite genetic algorithm. In particular, it is applied to minimum weight design examples of a three-bar truss, coil springs, a Z-section and a channel section. For the channel section, the optimal design using the tabu search method with random moves saved 26.14 percent over the weight of the SUMT method.

  5. A Novel Multiobjective Optimization Method Based on Sensitivity Analysis

    Directory of Open Access Journals (Sweden)

    Tiane Li

    2016-01-01

    Full Text Available For multiobjective optimization problems, different optimization variables have different influences on objectives, which implies that attention should be paid to the variables according to their sensitivity. However, previous optimization studies have not considered the variables sensitivity or conducted sensitivity analysis independent of optimization. In this paper, an integrated algorithm is proposed, which combines the optimization method SPEA (Strength Pareto Evolutionary Algorithm with the sensitivity analysis method SRCC (Spearman Rank Correlation Coefficient. In the proposed algorithm, the optimization variables are worked as samples of sensitivity analysis, and the consequent sensitivity result is used to guide the optimization process by changing the evolutionary parameters. Three cases including a mathematical problem, an airship envelope optimization, and a truss topology optimization are used to demonstrate the computational efficiency of the integrated algorithm. The results showed that this algorithm is able to simultaneously achieve parameter sensitivity and a well-distributed Pareto optimal set, without increasing the computational time greatly in comparison with the SPEA method.

  6. Characterization and mechanical separation of metals from computer Printed Circuit Boards (PCBs) based on mineral processing methods.

    Science.gov (United States)

    Sarvar, Mojtaba; Salarirad, Mohammad Mehdi; Shabani, Mohammad Amin

    2015-11-01

    In this paper, a novel mechanical process is proposed for enriching metal content of computer Printed Circuit Boards (PCBs). The PCBs are crushed and divided into three different size fractions namely: -0.59, +0.59 to 1.68 and +1.68 mm. Wet jigging and froth flotation methods are selected for metal enrichment. The coarse size fraction (+1.68 mm) is processed by jigging. The plastic free product is grinded and screened. The oversized product is separated as the first concentrate. It was rich of metal because the grinding process was selective. The undersized product is processed by froth flotation. Based on the obtained results, the middle size fraction (+0.59 to 1.68 mm) and the small size fraction (-0.59 mm) are processed by wet jigging and froth flotation respectively. The wet jigging process is optimized by investigating the effect of pulsation frequency and water flow rate. The results of examining the effect of particle size, solid to liquid ratio, conditioning time and using apolar collector showed that collectorless flotation is a promising method for separating nonmetals of PCBs. 95.6%, 97.5% and 85% of metal content of coarse size, middle size and small size fraction are recovered. The grades of obtained concentrates were 63.3%, 92.5% and 75% respectively. The total recovery is calculated as 95.64% and the grade of the final concentrate was 71.26%. Determining the grade of copper and gold in the final product reveals that 4.95% of copper and 24.46% of gold are lost during the concentration. The major part of the lost gold is accumulated in froth flotation tail. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Fast sequential Monte Carlo methods for counting and optimization

    CERN Document Server

    Rubinstein, Reuven Y; Vaisman, Radislav

    2013-01-01

    A comprehensive account of the theory and application of Monte Carlo methods Based on years of research in efficient Monte Carlo methods for estimation of rare-event probabilities, counting problems, and combinatorial optimization, Fast Sequential Monte Carlo Methods for Counting and Optimization is a complete illustration of fast sequential Monte Carlo techniques. The book provides an accessible overview of current work in the field of Monte Carlo methods, specifically sequential Monte Carlo techniques, for solving abstract counting and optimization problems. Written by authorities in the

  8. A line-source method for aligning on-board and other pinhole SPECT systems

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Susu [Medical Physics Graduate Program, Duke University, Durham, North Carolina 27710 (United States); Bowsher, James; Yin, Fang-Fang [Medical Physics Graduate Program, Duke University, Durham, North Carolina 27710 and Department of Radiation Oncology, Duke University Medical Center, Durham, North Carolina 27710 (United States)

    2013-12-15

    Purpose: In order to achieve functional and molecular imaging as patients are in position for radiation therapy, a robotic multipinhole SPECT system is being developed. Alignment of the SPECT system—to the linear accelerator (LINAC) coordinate frame and to the coordinate frames of other on-board imaging systems such as cone-beam CT (CBCT)—is essential for target localization and image reconstruction. An alignment method that utilizes line sources and one pinhole projection is proposed and investigated to achieve this goal. Potentially, this method could also be applied to the calibration of the other pinhole SPECT systems.Methods: An alignment model consisting of multiple alignment parameters was developed which maps line sources in three-dimensional (3D) space to their two-dimensional (2D) projections on the SPECT detector. In a computer-simulation study, 3D coordinates of line-sources were defined in a reference room coordinate frame, such as the LINAC coordinate frame. Corresponding 2D line-source projections were generated by computer simulation that included SPECT blurring and noise effects. The Radon transform was utilized to detect angles (α) and offsets (ρ) of the line-source projections. Alignment parameters were then estimated by a nonlinear least squares method, based on the α and ρ values and the alignment model. Alignment performance was evaluated as a function of number of line sources, Radon transform accuracy, finite line-source width, intrinsic camera resolution, Poisson noise, and acquisition geometry. Experimental evaluations were performed using a physical line-source phantom and a pinhole-collimated gamma camera attached to a robot.Results: In computer-simulation studies, when there was no error in determining angles (α) and offsets (ρ) of the measured projections, six alignment parameters (three translational and three rotational) were estimated perfectly using three line sources. When angles (α) and offsets (ρ) were provided by

  9. Comparative Study of Crosstalk Reduction Techniques in RF Printed Circuit Board Using FDTD Method

    Directory of Open Access Journals (Sweden)

    Rajeswari Packianathan

    2015-01-01

    Full Text Available Miniaturization of the feature size in modern electronic circuits results from placing interconnections in close proximity with a high packing density. As a result, coupling between the adjacent lines has increased significantly, causing crosstalk to become an important concern in high-performance circuit design. In certain applications, microstriplines may be used in printed circuit boards for propagating high-speed signals, rather than striplines. Here, the electromagnetic coupling effects are analyzed for various microstrip transmission line structures, namely, microstriplines with a guard trace, double stub microstriplines, and parallel serpentine microstriplines using the finite-difference time-domain method. The numerical results are compared with simulation results, where the variants are simulated using an Ansoft high-frequency structure simulator. The analysis and simulation results are experimentally validated by fabricating a prototype and establishing a good correspondence between them. Numerical results are compared with simulation and experimental results, showing that double stub microstriplines reduce the far end crosstalk by 7 dB and increase the near end crosstalk by about 2 dB compared with the parallel microstriplines. Parallel serpentine microstriplines reduce the far end crosstalk by more than 10 dB and also reduce more than 15 mV of peak far end crosstalk voltage, compared with parallel microstriplines.

  10. W-methods in optimal control

    NARCIS (Netherlands)

    J. Lang; J.G. Verwer (Jan)

    2013-01-01

    htmlabstractThis paper addresses consistency and stability of W-methods up to order three for nonlinear ODE-constrained control problems with possible restrictions on the control. The analysis is based on the transformed adjoint system and the control uniqueness property. These methods can also be

  11. A method optimization study for atomic absorption ...

    African Journals Online (AJOL)

    Sadia Ata

    2014-04-24

    Apr 24, 2014 ... spectrophotometric determination of total zinc in insulin using .... A linear regression by the least squares method is then applied. The value of the determination coefficient (R2 =0.99842) showed excellent linearity of the calibration curve for the ... method is applied repeatedly to multiple sampling of homol-.

  12. Control Methods Utilizing Energy Optimizing Schemes in Refrigeration Systems

    DEFF Research Database (Denmark)

    Larsen, L.S; Thybo, C.; Stoustrup, Jakob

    2003-01-01

    The potential energy savings in refrigeration systems using energy optimal control has been proved to be substantial. This however requires an intelligent control that drives the refrigeration systems towards the energy optimal state. This paper proposes an approach for a control, which drives th...... the condenser pressure towards an optimal state. The objective of this is to present a feasible method that can be used for energy optimizing control. A simulation model of a simple refrigeration system will be used as basis for testing the control method.......The potential energy savings in refrigeration systems using energy optimal control has been proved to be substantial. This however requires an intelligent control that drives the refrigeration systems towards the energy optimal state. This paper proposes an approach for a control, which drives...

  13. Flexible and generalized uncertainty optimization theory and methods

    CERN Document Server

    Lodwick, Weldon A

    2017-01-01

    This book presents the theory and methods of flexible and generalized uncertainty optimization. Particularly, it describes the theory of generalized uncertainty in the context of optimization modeling. The book starts with an overview of flexible and generalized uncertainty optimization. It covers uncertainties that are both associated with lack of information and that more general than stochastic theory, where well-defined distributions are assumed. Starting from families of distributions that are enclosed by upper and lower functions, the book presents construction methods for obtaining flexible and generalized uncertainty input data that can be used in a flexible and generalized uncertainty optimization model. It then describes the development of such a model in detail. All in all, the book provides the readers with the necessary background to understand flexible and generalized uncertainty optimization and develop their own optimization model. .

  14. Extremal Optimization: Methods Derived from Co-Evolution

    Energy Technology Data Exchange (ETDEWEB)

    Boettcher, S.; Percus, A.G.

    1999-07-13

    We describe a general-purpose method for finding high-quality solutions to hard optimization problems, inspired by self-organized critical models of co-evolution such as the Bak-Sneppen model. The method, called Extremal Optimization, successively eliminates extremely undesirable components of sub-optimal solutions, rather than ''breeding'' better components. In contrast to Genetic Algorithms which operate on an entire ''gene-pool'' of possible solutions, Extremal Optimization improves on a single candidate solution by treating each of its components as species co-evolving according to Darwinian principles. Unlike Simulated Annealing, its non-equilibrium approach effects an algorithm requiring few parameters to tune. With only one adjustable parameter, its performance proves competitive with, and often superior to, more elaborate stochastic optimization procedures. We demonstrate it here on two classic hard optimization problems: graph partitioning and the traveling salesman problem.

  15. Microstructure optimization design methods of the forging process and applications

    Institute of Scientific and Technical Information of China (English)

    WANG Guangchun; ZHAO Guoqun; GUAN Jing

    2007-01-01

    A microstructure optimization design method of the forging process is proposed. The optimization goal is the fine grain size and homogeneous grain distribution. The optimization object is the forging process parameters and the shape of the preform die. The grain size sub-objective function, the forgings shape sub-objective function and the whole objective function including the shape and the grain size are established, espectively. The detailed optimization steps are given. The microstructure optimization program is developed using the micro-genetic algorithm and the finite element method. Then, the upsetting process of the cylindrical billet is analyzed using a self-developed program. The forging parameters and the shape of preform die of the upsetting process are optimized respectively. The fine size and homogenous distribution of the grain can be achieved by controlling the shape of the preform die and improving the friction condition.

  16. Numerical methods for control optimization in linear systems

    Science.gov (United States)

    Tyatyushkin, A. I.

    2015-05-01

    Numerical methods are considered for solving optimal control problems in linear systems, namely, terminal control problems with control and phase constraints and time-optimal control problems. Several algorithms with various computer storage requirements are proposed for solving these problems. The algorithms are intended for finding an optimal control in linear systems having certain features, for example, when the reachable set of a system has flat faces.

  17. Method of product portfolio analysis based on optimization models

    Directory of Open Access Journals (Sweden)

    V.M. Lozyuk

    2011-12-01

    Full Text Available The research is devoted to optimization of the structure of product portfolio of trading company with using the principles of the investment modeling. We further developed the models of investment portfolio optimization, using the known Markowitz and Sharp methods to determine the optimal portfolio of trade company. Adapted to the goods market the models in this study could be applied to the business of trade companies.

  18. Software for optimization using a sequential simplex method

    Directory of Open Access Journals (Sweden)

    Evandro Bona

    2000-05-01

    Full Text Available A computer program for process optimization influenced by continuous and qualitative variables was developed from the simplex method. Software was validated through case studies found in literature by predictive models with two distinct processes. The obtained results showed great concordance with values supplied by literature. The developed program is portable and friendly, and may be used in several optimization systems. Software complementation with other subroutines, as combined response optimization, may make its application more comprehensive.

  19. Variable Neighborhood Simplex Search Methods for Global Optimization Models

    Directory of Open Access Journals (Sweden)

    Pongchanun Luangpaiboon

    2012-01-01

    Full Text Available Problem statement: Many optimization problems of practical interest are encountered in various fields of chemical, engineering and management sciences. They are computationally intractable. Therefore, a practical algorithm for solving such problems is to employ approximation algorithms that can find nearly optimums within a reasonable amount of computational time. Approach: In this study the hybrid methods combining the Variable Neighborhood Search (VNS and simplex’s family methods are proposed to deal with the global optimization problems of noisy continuous functions including constrained models. Basically, the simplex methods offer a search scheme without the gradient information whereas the VNS has the better searching ability with a systematic change of neighborhood of the current solution within a local search. Results: The VNS modified simplex method has a better searching ability for optimization problems with noise. The VNS modified simplex method also outperforms in average on the characteristics of intensity and diversity during the evolution of design point moving stage for the constrained optimization. Conclusion: The adaptive hybrid versions have proved to obtain significantly better results than the conventional methods. The amount of computation effort required for successful optimization is very sensitive to the rate of noise decrease of the process yields. Under circumstances of constrained optimization and gradually increasing the noise during an optimization the most preferred approach is the VNS modified simplex method.

  20. Genetic algorithm and particle swarm optimization combined with Powell method

    Science.gov (United States)

    Bento, David; Pinho, Diana; Pereira, Ana I.; Lima, Rui

    2013-10-01

    In recent years, the population algorithms are becoming increasingly robust and easy to use, based on Darwin's Theory of Evolution, perform a search for the best solution around a population that will progress according to several generations. This paper present variants of hybrid genetic algorithm - Genetic Algorithm and a bio-inspired hybrid algorithm - Particle Swarm Optimization, both combined with the local method - Powell Method. The developed methods were tested with twelve test functions from unconstrained optimization context.

  1. Reliability-based design optimization with Cross-Entropy method

    OpenAIRE

    Ghidey, Hiruy

    2015-01-01

    Implementation of the Cross-entropy (CE) method to solve reliability-based design optimization (RBDO) problems was investigated. The emphasis of this implementation method was to solve independently both the reliability and optimization sub-problems within the RBDO problem; therefore, the main aim of this study was to evaluate the performance of the Cross-entropy method in terms of efficiency and accuracy to solve RBDO problems. A numerical approach was followed in which the implementatio...

  2. A Decentralized Variable Ordering Method for Distributed Constraint Optimization

    Science.gov (United States)

    2005-05-01

    Either aproach can be used depending on how densely the nodes are connected inside blocks. If inside-block connec- tivity is sparse, the latter method ...A Decentralized Variable Ordering Method for Distributed Constraint Optimization Anton Chechetka Katia Sycara CMU-RI-TR-05-18 May 2005 Robotics...00-00-2005 4. TITLE AND SUBTITLE A Decentralized Variable Ordering Method for Distributed Constraint Optimization 5a. CONTRACT NUMBER 5b. GRANT

  3. Enhancement of the downhill simplex method of optimization

    Science.gov (United States)

    Koshel, R. John

    2002-12-01

    The downhill simplex method of optimization is a "geometric" method to achieve function minimization. The standard algorithm uses arbitrary values for the deterministic factors that describe the "movement" of the simplex in the merit space. While it is a robust method of optimization, it is relatively slow to converge to local minima. However, its stability and the lack of use of derivatives make it useful for optical design optimization, especially for the field of illumination. This paper describes preliminary efforts of optimizing the performance of the simplex optimizer. This enhancement is accomplished by optimizing the various control factors: alpha (reflection), beta (contraction), and gamma (expansion). This effort is accomplished by investigating the "end game" of optimal design, i.e., the shape of the figure of merit space is parabolic in N-dimensions near local minima. The figure of merit for the control factor optimization is the number of iterations to achieve a solution in comparison to the same case using the standard control factors. This optimization is done for parabolic wells of order N equals 2 to 15. In this study it is shown that with the correct choice of the control factors, one can achieve up to a 35% improvement in convergence. Techniques using gradient weighting and the inclusion of additional control factors are proposed.

  4. Co-iterative augmented Hessian method for orbital optimization

    CERN Document Server

    Sun, Qiming

    2016-01-01

    Orbital optimization procedure is widely called in electronic structure simulation. To efficiently find the orbital optimization solution, we developed a new second order orbital optimization algorithm, co-iteration augmented Hessian (CIAH) method. In this method, the orbital optimization is embedded in the diagonalization procedure for augmented Hessian (AH) eigenvalue equation. Hessian approximations can be easily employed in this method to improve the computational costs. We numerically performed the CIAH algorithm with SCF convergence of 20 challenging systems and Boys localization of C60 molecule. We found that CIAH algorithm has better SCF convergence and less computational costs than direct inversion iterative subspace (DIIS) algorithm. The numerical tests suggest that CIAH is a stable, reliable and efficient algorithm for orbital optimization problem.

  5. A hybrid optimization method for biplanar transverse gradient coil design

    Energy Technology Data Exchange (ETDEWEB)

    Qi Feng [Key Laboratory for Quantum Information and Measurements, Ministry of Education, School of Electronics Engineering and Computer Science, Peking University, Beijing 100871 (China); Tang Xin [Beijing Key Laboratory of Medical Physics and Engineering, Institute of Heavy Ion Physics, School of Physics, Peking University, Beijing 100871 (China); Jin Zhe [Key Laboratory for Quantum Information and Measurements, Ministry of Education, School of Electronics Engineering and Computer Science, Peking University, Beijing 100871 (China); Jiang Zhongde [Beijing Key Laboratory of Medical Physics and Engineering, Institute of Heavy Ion Physics, School of Physics, Peking University, Beijing 100871 (China); Shen Yifei [Key Laboratory for Quantum Information and Measurements, Ministry of Education, School of Electronics Engineering and Computer Science, Peking University, Beijing 100871 (China); Meng Bin [Key Laboratory for Quantum Information and Measurements, Ministry of Education, School of Electronics Engineering and Computer Science, Peking University, Beijing 100871 (China); Zu Donglin [Beijing Key Laboratory of Medical Physics and Engineering, Institute of Heavy Ion Physics, School of Physics, Peking University, Beijing 100871 (China); Wang Weimin [Key Laboratory for Quantum Information and Measurements, Ministry of Education, School of Electronics Engineering and Computer Science, Peking University, Beijing 100871 (China)

    2007-05-07

    The optimization of transverse gradient coils is one of the fundamental problems in designing magnetic resonance imaging gradient systems. A new approach is presented in this paper to optimize the transverse gradient coils' performance. First, in the traditional spherical harmonic target field method, high order coefficients, which are commonly ignored, are used in the first stage of the optimization process to give better homogeneity. Then, some cosine terms are introduced into the series expansion of stream function. These new terms provide simulated annealing optimization with new freedoms. Comparison between the traditional method and the optimized method shows that the inhomogeneity in the region of interest can be reduced from 5.03% to 1.39%, the coil efficiency increased from 3.83 to 6.31 mT m{sup -1} A{sup -1} and the minimum distance of these discrete coils raised from 1.54 to 3.16 mm.

  6. Machine Self-Teaching Methods for Parameter Optimization.

    Science.gov (United States)

    1986-12-01

    A199 285 MACHINE SELF- TEACHING METHODS FOR PARAMETER / OPTIMIZATION(U) NAVAL OCEAN SYSTEMS CENTER SAN DIEGO CA R A DILLARD DEC 86 NOSC/TR-1S39...Technical Document 1039 C) ,December 1986 Machine Self- Teaching Methods for Parameter Optimization Robin A. Dillard DTICS ELECTE MAY i01 𔄁 STAra Approved...ELEMEWt NO PROECi’ No TASK NO ARC Locally FundedI I1 I TE (ewd* Seawmy Cft*Wi., Machine Self- Teaching Methods for Parameter Optimization it PERSONAL

  7. Process control and optimization with simple interval calculation method

    DEFF Research Database (Denmark)

    Pomerantsev, A.; Rodionova, O.; Høskuldsson, Agnar

    2006-01-01

    the series of expanding PLS/SIC models in order to support the on-line process improvements. This method helps to predict the effect of planned actions on the product quality and thus enables passive quality control. We have also considered an optimization approach that proposes the correcting actions......Methods of process control and optimization are presented and illustrated with a real world example. The optimization methods are based on the PLS block modeling as well as on the simple interval calculation methods of interval prediction and object status classification. It is proposed to employ...... for the quality improvement in the course of production. The latter is an active quality optimization, which takes into account the actual history of the process. The advocate approach is allied to the conventional method of multivariate statistical process control (MSPC) as it also employs the historical process...

  8. Method of generating features optimal to a dataset and classifier

    Energy Technology Data Exchange (ETDEWEB)

    Bruillard, Paul J.; Gosink, Luke J.; Jarman, Kenneth D.

    2016-10-18

    A method of generating features optimal to a particular dataset and classifier is disclosed. A dataset of messages is inputted and a classifier is selected. An algebra of features is encoded. Computable features that are capable of describing the dataset from the algebra of features are selected. Irredundant features that are optimal for the classifier and the dataset are selected.

  9. Optimization of Nanostructuring Burnishing Technological Parameters by Taguchi Method

    Science.gov (United States)

    Kuznetsov, V. P.; Dmitriev, A. I.; Anisimova, G. S.; Semenova, Yu V.

    2016-04-01

    On the basis of application of Taguchi optimization method, an approach for researching influence of nanostructuring burnishing technological parameters, considering the surface layer microhardness criterion, is developed. Optimal values of burnishing force, feed and number of tool passes for hardened steel AISI 420 hardening treatment are defined.

  10. Maximum super angle optimization method for array antenna pattern synthesis

    DEFF Research Database (Denmark)

    Wu, Ji; Roederer, A. G

    1991-01-01

    Different optimization criteria related to antenna pattern synthesis are discussed. Based on the maximum criteria and vector space representation, a simple and efficient optimization method is presented for array and array fed reflector power pattern synthesis. A sector pattern synthesized by a 20...

  11. Exact and useful optimization methods for microeconomics

    NARCIS (Netherlands)

    Balder, E.J.

    2011-01-01

    This paper points out that the treatment of utility maximization in current textbooks on microeconomic theory is deficient in at least three respects: breadth of coverage, completeness-cum-coherence of solution methods and mathematical correctness. Improvements are suggested in the form of a Kuhn-Tu

  12. A novel reutilization method for waste printed circuit boards as flame retardant and smoke suppressant for poly (vinyl chloride)

    Energy Technology Data Exchange (ETDEWEB)

    Xiu, Fu-Rong, E-mail: xiu_chem@hotmail.com [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350108 (China); Weng, Huiwei; Qi, Yingying; Yu, Gending; Zhang, Zhigang [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350108 (China); Zhang, Fu-Shen [Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

    2016-09-05

    Highlights: • We report a novel electronic waste-based flame retardant for PVC. • The SCWO-treated PCBs significantly improves the flame retardancy of PVC. • The flame retardant mechanism of SCWO-treated PCBs was studied. • Appropriate amount flame retardant does not degrade the mechanical property of PVC. - Abstract: In this study, a novel reutilization method for waste printed circuit boards (PCBs) as flame retardant and smoke suppressant for poly (vinyl chloride) (PVC) was successfully testified. A supercritical water oxidation (SCWO) process was applied to treat waste PCBs before they could be used as flame retardants of PVC. The results indicated that SCWO conditions had a significant effect on the flame retarding and smoke suppressing properties of waste PCBs for PVC. Cu{sub 2}O, CuO, and SnO{sub 2} were the main active ingredients in waste PCBs-derived flame retardants. A conversion of Cu elements (Cu{sup 0} → Cu{sup +} → Cu{sup 2+}) during SCWO process with the increase of reaction temperature was found to be the key influence factor for the flame retarding properties of SCWO-treated PCBs. The experiment results also showed that there was a synergistic effect of flame retardancy between Cu{sup +} and Cu{sup 2+}. After the optimized SCWO treatment, SCWO-treated PCBs significantly improved the flame retardancy and smoke suppression of PVC. Limiting oxygen index (LOI) and char yield (CY) increased with increasing SCWO-treated PCBs content in PVC, while smoke density rating (SDR) and maximum smoke density (MSD) decreased markedly. The mechanical properties of PVC samples were influenced in different degree by adding different content SCWO-treated PCBs.

  13. Reliability-based design optimization using convex approximations and sequential optimization and reliability assessment method

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Tae Min; Lee, Byung Chai [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2010-01-15

    In this study, an effective method for reliability-based design optimization (RBDO) is proposed enhancing sequential optimization and reliability assessment (SORA) method by convex approximations. In SORA, reliability estimation and deterministic optimization are performed sequentially. The sensitivity and function value of probabilistic constraint at the most probable point (MPP) are obtained in the reliability analysis loop. In this study, the convex approximations for probabilistic constraint are constructed by utilizing the sensitivity and function value of the probabilistic constraint at the MPP. Hence, the proposed method requires much less function evaluations of probabilistic constraints in the deterministic optimization than the original SORA method. The efficiency and accuracy of the proposed method were verified through numerical examples

  14. Lattice Boltzmann method for shape optimization of fluid distributor

    CERN Document Server

    Wang, Limin; Luo, Lingai

    2013-01-01

    This paper presents the shape optimization of a flat-type arborescent fluid distributor for the purpose of process intensification. A shape optimization algorithm based on the lattice Boltzmann method (LBM) is proposed with the objective of decreasing the flow resistance of such distributor at the constraint of constant fluid volume. Prototypes of the initial distributor as well as the optimized one are designed. Fluid distribution and hydraulic characteristics of these distributors are investigated numerically. Results show that the pressure drop of the optimized distributor is between 15.9% and 25.1% lower than that of the initial reference while keeping a uniform flow distribution, demonstrating the process intensification in fluid distributor, and suggesting the interests of the proposed optimization algorithm in engineering optimal design.

  15. Optimization Methods for Supply Chain Activities

    Directory of Open Access Journals (Sweden)

    Balasescu S.

    2014-12-01

    Full Text Available This paper approach the theme of supply chain activities for medium and large companies which run many operations and need many facilities. The first goal is to analyse the influence of optimisation methods of supply chain activities on the success rate for a business. The second goal is to compare some logistic strategies applied by companies with the same profile to see which is the most effective. The final goal is to show which is the necessity of strategic optimum for a company and how can be achieved the considering the demand uncertainty.

  16. OPTIMAL SIGNAL PROCESSING METHODS IN GPR

    Directory of Open Access Journals (Sweden)

    Saeid Karamzadeh

    2014-01-01

    Full Text Available In the past three decades, a lot of various applications of Ground Penetrating Radar (GPR took place in real life. There are important challenges of this radar in civil applications and also in military applications. In this paper, the fundamentals of GPR systems will be covered and three important signal processing methods (Wavelet Transform, Matched Filter and Hilbert Huang will be compared to each other in order to get most accurate information about objects which are in subsurface or behind the wall.

  17. Optimization Design based on BP Neural Network and GA Method

    Directory of Open Access Journals (Sweden)

    Bing Wang

    2013-12-01

    Full Text Available This study puts forward one kind optimization controlling solution method on complicated system. At first modeling using neural network then adopt the real data to structure the neural network model of pertinence, make the parameter to seek to the neural network model excellently by mixing GA finally, thus got intelligence to the complicated system to optimize and control. The method can identify network configuration and network training methods. By adopting the number coding and effectively reducing the network size and the network convergence time, increase the network training speed. The study provides this and optimizes relevant MATLAB procedure which controls the method, so long as adjust a little to the concrete problem, can believe this procedure well the optimization of the complicated system controls the problem in the reality of solving.

  18. Monte-Carlo tree search method for the board game Scotland Yard

    OpenAIRE

    BELEJ, NEŽA

    2015-01-01

    In the thesis we learn about the field of artificial intelligence that investigates board games and their program-based solutions. We examine Monte-Carlo tree search algorithm and transfer it to well-known board game Scotland Yard, considering advices from Nijssen and Winands. We focus mainly on the third phase of the algorithm, playout, and decide to implement it in three different ways (from less to more advanced techniques). We compare these three aproaches. We compare the win rates and co...

  19. Numerical methods for solving terminal optimal control problems

    Science.gov (United States)

    Gornov, A. Yu.; Tyatyushkin, A. I.; Finkelstein, E. A.

    2016-02-01

    Numerical methods for solving optimal control problems with equality constraints at the right end of the trajectory are discussed. Algorithms for optimal control search are proposed that are based on the multimethod technique for finding an approximate solution of prescribed accuracy that satisfies terminal conditions. High accuracy is achieved by applying a second-order method analogous to Newton's method or Bellman's quasilinearization method. In the solution of problems with direct control constraints, the variation of the control is computed using a finite-dimensional approximation of an auxiliary problem, which is solved by applying linear programming methods.

  20. Research of the Optimization Methods for Mass Customization (MC)

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A group of graphical models and mathematical models a re used to describe the methods of mass customization (MC). The relationships am ong the models and methods are shown in Fig.1. Fig.1 Relationships among optimization methods for MCThe methods for MC relate to both of product and process, also customized quanti ty and deepness. The methods for MC are integrated by the work in the paper, whi ch can help to understand and use MC better. The optimization and standardization of product is the key for M...

  1. Comparison of optimal design methods in inverse problems

    Science.gov (United States)

    Banks, H. T.; Holm, K.; Kappel, F.

    2011-07-01

    Typical optimal design methods for inverse or parameter estimation problems are designed to choose optimal sampling distributions through minimization of a specific cost function related to the resulting error in parameter estimates. It is hoped that the inverse problem will produce parameter estimates with increased accuracy using data collected according to the optimal sampling distribution. Here we formulate the classical optimal design problem in the context of general optimization problems over distributions of sampling times. We present a new Prohorov metric-based theoretical framework that permits one to treat succinctly and rigorously any optimal design criteria based on the Fisher information matrix. A fundamental approximation theory is also included in this framework. A new optimal design, SE-optimal design (standard error optimal design), is then introduced in the context of this framework. We compare this new design criterion with the more traditional D-optimal and E-optimal designs. The optimal sampling distributions from each design are used to compute and compare standard errors; the standard errors for parameters are computed using asymptotic theory or bootstrapping and the optimal mesh. We use three examples to illustrate ideas: the Verhulst-Pearl logistic population model (Banks H T and Tran H T 2009 Mathematical and Experimental Modeling of Physical and Biological Processes (Boca Raton, FL: Chapman and Hall/CRC)), the standard harmonic oscillator model (Banks H T and Tran H T 2009) and a popular glucose regulation model (Bergman R N, Ider Y Z, Bowden C R and Cobelli C 1979 Am. J. Physiol. 236 E667-77 De Gaetano A and Arino O 2000 J. Math. Biol. 40 136-68 Toffolo G, Bergman R N, Finegood D T, Bowden C R and Cobelli C 1980 Diabetes 29 979-90).

  2. Optimizing municipal wastewater treatment plants using an improved multi-objective optimization method.

    Science.gov (United States)

    Zhang, Rui; Xie, Wen-Ming; Yu, Han-Qing; Li, Wen-Wei

    2014-04-01

    An improved multi-objective optimization (MOO) model was established and used for simultaneously optimizing the treatment cost and multiple effluent quality indexes (including effluent COD, NH4(+)-N, NO3(-)-N) of a municipal wastewater treatment plant (WWTP). Compared with previous models that were mainly based on the use of fixed decision factors and did not taken into account the treatment cost, this model introduces a relationship model based on back propagation algorithm to determine the set of decision factors according to the expected optimization targets. Thus, a more flexible and precise optimization of the treatment process was allowed. Moreover, a MOO of conflicting objectives (i.e., treatment cost and effluent quality) was achieved. Applying this method, an optimal balance between operating cost and effluent quality of a WWTP can be found. This model may offer a useful tool for optimized design and control of practical WWTPs.

  3. An improved optimal elemental method for updating finite element models

    Institute of Scientific and Technical Information of China (English)

    Duan Zhongdong(段忠东); Spencer B.F.; Yan Guirong(闫桂荣); Ou Jinping(欧进萍)

    2004-01-01

    The optimal matrix method and optimal elemental method used to update finite element models may not provide accurate results. This situation occurs when the test modal model is incomplete, as is often the case in practice. An improved optimal elemental method is presented that defines a new objective function, and as a byproduct, circumvents the need for mass normalized modal shapes, which are also not readily available in practice. To solve the group of nonlinear equations created by the improved optimal method, the Lagrange multiplier method and Matlab function fmincon are employed. To deal with actual complex structures,the float-encoding genetic algorithm (FGA) is introduced to enhance the capability of the improved method. Two examples, a 7-degree of freedom (DOF) mass-spring system and a 53-DOF planar frame, respectively, are updated using the improved method.Thc example results demonstrate the advantages of the improved method over existing optimal methods, and show that the genetic algorithm is an effective way to update the models used for actual complex structures.

  4. A Numerical Embedding Method for Solving the Nonlinear Optimization Problem

    Institute of Scientific and Technical Information of China (English)

    田保锋; 戴云仙; 孟泽红; 张建军

    2003-01-01

    A numerical embedding method was proposed for solving the nonlinear optimization problem. By using the nonsmooth theory, the existence and the continuation of the following path for the corresponding homotopy equations were proved. Therefore the basic theory for the algorithm of the numerical embedding method for solving the non-linear optimization problem was established. Based on the theoretical results, a numerical embedding algorithm was designed for solving the nonlinear optimization problem, and prove its convergence carefully. Numerical experiments show that the algorithm is effective.

  5. Method and system for SCR optimization

    Science.gov (United States)

    Lefebvre, Wesley Curt; Kohn, Daniel W.

    2009-03-10

    Methods and systems are provided for controlling SCR performance in a boiler. The boiler includes one or more generally cross sectional areas. Each cross sectional area can be characterized by one or more profiles of one or more conditions affecting SCR performance and be associated with one or more adjustable desired profiles of the one or more conditions during the operation of the boiler. The performance of the boiler can be characterized by boiler performance parameters. A system in accordance with one or more embodiments of the invention can include a controller input for receiving a performance goal for the boiler corresponding to at least one of the boiler performance parameters and for receiving data values corresponding to boiler control variables and to the boiler performance parameters. The boiler control variables include one or more current profiles of the one or more conditions. The system also includes a system model that relates one or more profiles of the one or more conditions in the boiler to the boiler performance parameters. The system also includes an indirect controller that determines one or more desired profiles of the one or more conditions to satisfy the performance goal for the boiler. The indirect controller uses the system model, the received data values and the received performance goal to determine the one or more desired profiles of the one or more conditions. The system model also includes a controller output that outputs the one or more desired profiles of the one or more conditions.

  6. Local Approximation and Hierarchical Methods for Stochastic Optimization

    Science.gov (United States)

    Cheng, Bolong

    In this thesis, we present local and hierarchical approximation methods for two classes of stochastic optimization problems: optimal learning and Markov decision processes. For the optimal learning problem class, we introduce a locally linear model with radial basis function for estimating the posterior mean of the unknown objective function. The method uses a compact representation of the function which avoids storing the entire history, as is typically required by nonparametric methods. We derive a knowledge gradient policy with the locally parametric model, which maximizes the expected value of information. We show the policy is asymptotically optimal in theory, and experimental works suggests that the method can reliably find the optimal solution on a range of test functions. For the Markov decision processes problem class, we are motivated by an application where we want to co-optimize a battery for multiple revenue, in particular energy arbitrage and frequency regulation. The nature of this problem requires the battery to make charging and discharging decisions at different time scales while accounting for the stochastic information such as load demand, electricity prices, and regulation signals. Computing the exact optimal policy becomes intractable due to the large state space and the number of time steps. We propose two methods to circumvent the computation bottleneck. First, we propose a nested MDP model that structure the co-optimization problem into smaller sub-problems with reduced state space. This new model allows us to understand how the battery behaves down to the two-second dynamics (that of the frequency regulation market). Second, we introduce a low-rank value function approximation for backward dynamic programming. This new method only requires computing the exact value function for a small subset of the state space and approximate the entire value function via low-rank matrix completion. We test these methods on historical price data from the

  7. Thickness optimization of laminated composites using the discrete material optimization method

    DEFF Research Database (Denmark)

    Sørensen, Søren Nørgaard; Sørensen, Rene; Lund, Erik

    2012-01-01

    This work concerns a novel large scale multi-material topology optimization method for simultaneous determination of the optimum variable integer thickness and fiber orientation throughout laminated composites with fixed outer geometries while adhering to certain manufacturing constraints....... The conceptual combinatorial/integer problem is relaxed to a continuous problem and solved on basis of the so-called Discrete Material Optimization method, explicitly including the manufacturing constraints as linear constraints....

  8. Method for Determining Optimal Residential Energy Efficiency Retrofit Packages

    Energy Technology Data Exchange (ETDEWEB)

    Polly, B.; Gestwick, M.; Bianchi, M.; Anderson, R.; Horowitz, S.; Christensen, C.; Judkoff, R.

    2011-04-01

    Businesses, government agencies, consumers, policy makers, and utilities currently have limited access to occupant-, building-, and location-specific recommendations for optimal energy retrofit packages, as defined by estimated costs and energy savings. This report describes an analysis method for determining optimal residential energy efficiency retrofit packages and, as an illustrative example, applies the analysis method to a 1960s-era home in eight U.S. cities covering a range of International Energy Conservation Code (IECC) climate regions. The method uses an optimization scheme that considers average energy use (determined from building energy simulations) and equivalent annual cost to recommend optimal retrofit packages specific to the building, occupants, and location. Energy savings and incremental costs are calculated relative to a minimum upgrade reference scenario, which accounts for efficiency upgrades that would occur in the absence of a retrofit because of equipment wear-out and replacement with current minimum standards.

  9. On some other preferred method for optimizing the welded joint

    Directory of Open Access Journals (Sweden)

    Pejović Branko B.

    2016-01-01

    Full Text Available The paper shows an example of performed optimization of sizes in terms of welding costs in a characteristic loaded welded joint. Hence, in the first stage, the variables and constant parameters are defined, and mathematical shape of the optimization function is determined. The following stage of the procedure defines and places the most important constraint functions that limit the design of structures, that the technologist and the designer should take into account. Subsequently, a mathematical optimization model of the problem is derived, that is efficiently solved by a proposed method of geometric programming. Further, a mathematically based thorough optimization algorithm is developed of the proposed method, with a main set of equations defining the problem that are valid under certain conditions. Thus, the primary task of optimization is reduced to the dual task through a corresponding function, which is easier to solve than the primary task of the optimized objective function. The main reason for this is a derived set of linear equations. Apparently, a correlation is used between the optimal primary vector that minimizes the objective function and the dual vector that maximizes the dual function. The method is illustrated on a computational practical example with a different number of constraint functions. It is shown that for the case of a lower level of complexity, a solution is reached through an appropriate maximization of the dual function by mathematical analysis and differential calculus.

  10. Review: Optimization methods for groundwater modeling and management

    Science.gov (United States)

    Yeh, William W.-G.

    2015-09-01

    Optimization methods have been used in groundwater modeling as well as for the planning and management of groundwater systems. This paper reviews and evaluates the various optimization methods that have been used for solving the inverse problem of parameter identification (estimation), experimental design, and groundwater planning and management. Various model selection criteria are discussed, as well as criteria used for model discrimination. The inverse problem of parameter identification concerns the optimal determination of model parameters using water-level observations. In general, the optimal experimental design seeks to find sampling strategies for the purpose of estimating the unknown model parameters. A typical objective of optimal conjunctive-use planning of surface water and groundwater is to minimize the operational costs of meeting water demand. The optimization methods include mathematical programming techniques such as linear programming, quadratic programming, dynamic programming, stochastic programming, nonlinear programming, and the global search algorithms such as genetic algorithms, simulated annealing, and tabu search. Emphasis is placed on groundwater flow problems as opposed to contaminant transport problems. A typical two-dimensional groundwater flow problem is used to explain the basic formulations and algorithms that have been used to solve the formulated optimization problems.

  11. Geometry Optimization of a Segmented Thermoelectric Generator Based on Multi-parameter and Nonlinear Optimization Method

    Science.gov (United States)

    Cai, Lanlan; Li, Peng; Luo, Qi; Zhai, Pengcheng; Zhang, Qingjie

    2017-03-01

    As no single thermoelectric material has presented a high figure-of-merit (ZT) over a very wide temperature range, segmented thermoelectric generators (STEGs), where the p- and n-legs are formed of different thermoelectric material segments joined in series, have been developed to improve the performance of thermoelectric generators. A crucial but difficult problem in a STEG design is to determine the optimal values of the geometrical parameters, like the relative lengths of each segment and the cross-sectional area ratio of the n- and p-legs. Herein, a multi-parameter and nonlinear optimization method, based on the Improved Powell Algorithm in conjunction with the discrete numerical model, was implemented to solve the STEG's geometrical optimization problem. The multi-parameter optimal results were validated by comparison with the optimal outcomes obtained from the single-parameter optimization method. Finally, the effect of the hot- and cold-junction temperatures on the geometry optimization was investigated. Results show that the optimal geometry parameters for maximizing the specific output power of a STEG are different from those for maximizing the conversion efficiency. Data also suggest that the optimal geometry parameters and the interfacial temperatures of the adjacent segments optimized for maximum specific output power or conversion efficiency vary with changing hot- and cold-junction temperatures. Through the geometry optimization, the CoSb3/Bi2Te3-based STEG can obtain a maximum specific output power up to 1725.3 W/kg and a maximum efficiency of 13.4% when operating at a hot-junction temperature of 823 K and a cold-junction temperature of 298 K.

  12. A Novel Optimal Control Method for Impulsive-Correction Projectile Based on Particle Swarm Optimization

    Directory of Open Access Journals (Sweden)

    Ruisheng Sun

    2016-01-01

    Full Text Available This paper presents a new parametric optimization approach based on a modified particle swarm optimization (PSO to design a class of impulsive-correction projectiles with discrete, flexible-time interval, and finite-energy control. In terms of optimal control theory, the task is described as the formulation of minimum working number of impulses and minimum control error, which involves reference model linearization, boundary conditions, and discontinuous objective function. These result in difficulties in finding the global optimum solution by directly utilizing any other optimization approaches, for example, Hp-adaptive pseudospectral method. Consequently, PSO mechanism is employed for optimal setting of impulsive control by considering the time intervals between two neighboring lateral impulses as design variables, which makes the briefness of the optimization process. A modification on basic PSO algorithm is developed to improve the convergence speed of this optimization through linearly decreasing the inertial weight. In addition, a suboptimal control and guidance law based on PSO technique are put forward for the real-time consideration of the online design in practice. Finally, a simulation case coupled with a nonlinear flight dynamic model is applied to validate the modified PSO control algorithm. The results of comparative study illustrate that the proposed optimal control algorithm has a good performance in obtaining the optimal control efficiently and accurately and provides a reference approach to handling such impulsive-correction problem.

  13. Using necessary optimality conditions for acceleration of the nonuniform covering optimization method

    Directory of Open Access Journals (Sweden)

    Evtushenko Yury

    2016-01-01

    Full Text Available Paper deals with the non-uniform covering method that is aimed at deterministic global optimization. This method finds a feasible solution to the optimization problem numerically and proves that the obtained solution differs from the optimal by no more than a given accuracy. Numerical proof consists of constructing a set of covering sets - the coverage. The number of elements in the coverage can be very large and even exceed the total amount of available computer resources. Basic method of coverage construction is the comparison of upper and lower bounds on the value of the objective function. In this work we propose to use necessary optimality conditions of first and second order for reducing the search for boxconstrained problems. We provide the algorithm description and prove its correctness. The efficiency of the proposed approach is studied on test problems.

  14. A weak Hamiltonian finite element method for optimal control problems

    Science.gov (United States)

    Hodges, Dewey H.; Bless, Robert R.

    1990-01-01

    A temporal finite element method based on a mixed form of the Hamiltonian weak principle is developed for dynamics and optimal control problems. The mixed form of Hamilton's weak principle contains both displacements and momenta as primary variables that are expanded in terms of nodal values and simple polynomial shape functions. Unlike other forms of Hamilton's principle, however, time derivatives of the momenta and displacements do not appear therein; instead, only the virtual momenta and virtual displacements are differentiated with respect to time. Based on the duality that is observed to exist between the mixed form of Hamilton's weak principle and variational principles governing classical optimal control problems, a temporal finite element formulation of the latter can be developed in a rather straightforward manner. Several well-known problems in dynamics and optimal control are illustrated. The example dynamics problem involves a time-marching problem. As optimal control examples, elementary trajectory optimization problems are treated.

  15. Weak Hamiltonian finite element method for optimal control problems

    Science.gov (United States)

    Hodges, Dewey H.; Bless, Robert R.

    1991-01-01

    A temporal finite element method based on a mixed form of the Hamiltonian weak principle is developed for dynamics and optimal control problems. The mixed form of Hamilton's weak principle contains both displacements and momenta as primary variables that are expanded in terms of nodal values and simple polynomial shape functions. Unlike other forms of Hamilton's principle, however, time derivatives of the momenta and displacements do not appear therein; instead, only the virtual momenta and virtual displacements are differentiated with respect to time. Based on the duality that is observed to exist between the mixed form of Hamilton's weak principle and variational principles governing classical optimal control problems, a temporal finite element formulation of the latter can be developed in a rather straightforward manner. Several well-known problems in dynamics and optimal control are illustrated. The example dynamics problem involves a time-marching problem. As optimal control examples, elementary trajectory optimization problems are treated.

  16. Efficient Hybrid Optimal Design Method for Power Electronics Converters

    CERN Document Server

    AUTHOR|(SzGeCERN)697719; Aguglia, Davide; Viarouge, Philippe; Cros, Jérôme

    2015-01-01

    This paper presents a novel design methodology for dimensioning optimal power-electronic converters, which is able to achieve the precision of numerical simulation-based optimization procedures, however minimizing the overall computation time. The approach is based on the utilization of analytical and frequency-domain design models for a numerical optimization process, a validation with numerical simulations of the intermediate optimal solutions, and the correction of the analytical design models precision from the numerical simulation results. This method allows using the numerical simulation in an efficient way, where typically less than ten correction iterations are required. In order to demonstrate the performances of the proposed methodology, the calculation of the control parameters for an H-bridge DC-DC converter and the optimal dimensioning of a damped output filter for a buck converter using the proposed approach is presented.

  17. Robust Collaborative Optimization Method Based on Dual-response Surface

    Institute of Scientific and Technical Information of China (English)

    WANG Wei; FAN Wenhui; CHANG Tianqing; YUAN Yuming

    2009-01-01

    A novel method for robust collaborative design of complex products based on dual-response surface (DRS-RCO) is proposed to solve multidisciplinary design optimization (MDO) problems under uncertainty. Collaborative optimization (CO) which decomposes the whole system into a double-level nonlinear optimization problem is widely Accepted as an efficient method to solve MDO problems. In order to improve the quality of complex product in design process, robust collaborative optimization (RCO) is developed to solve those problems under uncertain conditions. RCO does opfmiTation on the linear sum of mean and standard deviation of objective function and gets an optimal solution with high robustnmess. Response surfaces method is an important way to do approximation in robust design. DRS-RCO is an improved RCO method in which dual-response surface replaces system uncertainty analysis module of CO. The dual-response surface is the approximate model of mean and standard deviation of objective function respectively. In DRS-RCO, All the information of subsystems is included in dual-response surfaces. As an additional item, the standard deviation of objective function is added to the subsystem optimization. This item guarantee both the mean and standard deviation of this subsystem is reaching the minima at the same time. Finally, a test problem with two coupled subsystems is conducted to verify the feasibility and effectiveness of DRS-RCO.

  18. RELATIVE CAMERA POSE ESTIMATION METHOD USING OPTIMIZATION ON THE MANIFOLD

    Directory of Open Access Journals (Sweden)

    C. Cheng

    2017-05-01

    Full Text Available To solve the problem of relative camera pose estimation, a method using optimization with respect to the manifold is proposed. Firstly from maximum-a-posteriori (MAP model to nonlinear least squares (NLS model, the general state estimation model using optimization is derived. Then the camera pose estimation model is applied to the general state estimation model, while the parameterization of rigid body transformation is represented by Lie group/algebra. The jacobian of point-pose model with respect to Lie group/algebra is derived in detail and thus the optimization model of rigid body transformation is established. Experimental results show that compared with the original algorithms, the approaches with optimization can obtain higher accuracy both in rotation and translation, while avoiding the singularity of Euler angle parameterization of rotation. Thus the proposed method can estimate relative camera pose with high accuracy and robustness.

  19. Development of optimization method for plate heat exchanger with undulation

    Directory of Open Access Journals (Sweden)

    Dvořák Václav

    2016-01-01

    Full Text Available The article deals with optimization of undulated heat transfer surface of plate heat exchanger. The goal of optimization is not only to increase effectiveness of heat transfer but also to reduce the pressure drop. A combined pattern of undulation which combines herringbone pattern and wavy pattern was optimized and best values of four parameters were found; angle of herringbone pattern, number, phase and amplitude of longitudinal waves of wavy pattern. The optimization procedure looked for maximum of objective function which was a linear combination of effectiveness and pressure drop. We used simple Monte Carlo method and the optimum was searched for four values of reference pressure drop. Four different optimization were run and we investigated the effect of various definition of objective function and parameters of undulation. It was found that during optimization of combined pattern, the herringbone pattern is more favoured than wavy pattern. It is caused by the fact that herringbone pattern was described by the only one free parameter, which was the angle of undulation, and therefore it is more likely to be found by a stochastic method. This assumption was confirmed when simple wavy pattern was optimized and higher values of objective function and effectiveness were found.

  20. Optimization methods and silicon solar cell numerical models

    Science.gov (United States)

    Girardini, K.

    1986-01-01

    The goal of this project is the development of an optimization algorithm for use with a solar cell model. It is possible to simultaneously vary design variables such as impurity concentrations, front junction depth, back junctions depth, and cell thickness to maximize the predicted cell efficiency. An optimization algorithm has been developed and interfaced with the Solar Cell Analysis Program in 1 Dimension (SCAPID). SCAPID uses finite difference methods to solve the differential equations which, along with several relations from the physics of semiconductors, describe mathematically the operation of a solar cell. A major obstacle is that the numerical methods used in SCAPID require a significant amount of computer time, and during an optimization the model is called iteratively until the design variables converge to the value associated with the maximum efficiency. This problem has been alleviated by designing an optimization code specifically for use with numerically intensive simulations, to reduce the number of times the efficiency has to be calculated to achieve convergence to the optimal solution. Adapting SCAPID so that it could be called iteratively by the optimization code provided another means of reducing the cpu time required to complete an optimization. Instead of calculating the entire I-V curve, as is usually done in SCAPID, only the efficiency is calculated (maximum power voltage and current) and the solution from previous calculations is used to initiate the next solution.

  1. A class of trust-region methods for parallel optimization

    Energy Technology Data Exchange (ETDEWEB)

    P. D. Hough; J. C. Meza

    1999-03-01

    The authors present a new class of optimization methods that incorporates a Parallel Direct Search (PDS) method within a trust-region Newton framework. This approach combines the inherent parallelism of PDS with the rapid and robust convergence properties of Newton methods. Numerical tests have yielded favorable results for both standard test problems and engineering applications. In addition, the new method appears to be more robust in the presence of noisy functions that are inherent in many engineering simulations.

  2. System Design Support by Optimization Method Using Stochastic Process

    Science.gov (United States)

    Yoshida, Hiroaki; Yamaguchi, Katsuhito; Ishikawa, Yoshio

    We proposed the new optimization method based on stochastic process. The characteristics of this method are to obtain the approximate solution of the optimum solution as an expected value. In numerical calculation, a kind of Monte Carlo method is used to obtain the solution because of stochastic process. Then, it can obtain the probability distribution of the design variable because it is generated in the probability that design variables were in proportion to the evaluation function value. This probability distribution shows the influence of design variables on the evaluation function value. This probability distribution is the information which is very useful for the system design. In this paper, it is shown the proposed method is useful for not only the optimization but also the system design. The flight trajectory optimization problem for the hang-glider is shown as an example of the numerical calculation.

  3. Optimal Combination of Aircraft Maintenance Tasks by a Novel Simplex Optimization Method

    Directory of Open Access Journals (Sweden)

    Huaiyuan Li

    2015-01-01

    Full Text Available Combining maintenance tasks into work packages is not only necessary for arranging maintenance activities, but also critical for the reduction of maintenance cost. In order to optimize the combination of maintenance tasks by fuzzy C-means clustering algorithm, an improved fuzzy C-means clustering model is introduced in this paper. In order to reduce the dimension, variables representing clustering centers are eliminated in the improved cluster model. So the improved clustering model can be directly solved by the optimization method. To optimize the clustering model, a novel nonlinear simplex optimization method is also proposed in this paper. The novel method searches along all rays emitting from the center to each vertex, and those search directions are rightly n+1 positive basis. The algorithm has both theoretical convergence and good experimental effect. Taking the optimal combination of some maintenance tasks of a certain aircraft as an instance, the novel simplex optimization method and the clustering model both exhibit excellent performance.

  4. Optimal Route Selection Method Based on Vague Sets

    Institute of Scientific and Technical Information of China (English)

    GUO Rui; DU Li min; WANG Chun

    2015-01-01

    Optimal route selection is an important function of vehicle trac flow guidance system. Its core is to determine the index weight for measuring the route merits and to determine the evaluation method for selecting route. In this paper, subjective weighting method which relies on driver preference is used to determine the weight and the paper proposes the multi-criteria weighted decision method based on vague sets for selecting the optimal route. Examples show that, the usage of vague sets to describe route index value can provide more decision-making information for route selection.

  5. Deterministic operations research models and methods in linear optimization

    CERN Document Server

    Rader, David J

    2013-01-01

    Uniquely blends mathematical theory and algorithm design for understanding and modeling real-world problems Optimization modeling and algorithms are key components to problem-solving across various fields of research, from operations research and mathematics to computer science and engineering. Addressing the importance of the algorithm design process. Deterministic Operations Research focuses on the design of solution methods for both continuous and discrete linear optimization problems. The result is a clear-cut resource for understanding three cornerstones of deterministic operations resear

  6. Adaptive Mixed Finite Element Methods for Parabolic Optimal Control Problems

    OpenAIRE

    Zuliang Lu

    2011-01-01

    We will investigate the adaptive mixed finite element methods for parabolic optimal control problems. The state and the costate are approximated by the lowest-order Raviart-Thomas mixed finite element spaces, and the control is approximated by piecewise constant elements. We derive a posteriori error estimates of the mixed finite element solutions for optimal control problems. Such a posteriori error estimates can be used to construct more efficient and reliable adaptive mixed finite element ...

  7. A new hybrid optimization method inspired from swarm intelligence: Fuzzy adaptive swallow swarm optimization algorithm (FASSO

    Directory of Open Access Journals (Sweden)

    Mehdi Neshat

    2015-11-01

    Full Text Available In this article, the objective was to present effective and optimal strategies aimed at improving the Swallow Swarm Optimization (SSO method. The SSO is one of the best optimization methods based on swarm intelligence which is inspired by the intelligent behaviors of swallows. It has been able to offer a relatively strong method for solving optimization problems. However, despite its many advantages, the SSO suffers from two shortcomings. Firstly, particles movement speed is not controlled satisfactorily during the search due to the lack of an inertia weight. Secondly, the variables of the acceleration coefficient are not able to strike a balance between the local and the global searches because they are not sufficiently flexible in complex environments. Therefore, the SSO algorithm does not provide adequate results when it searches in functions such as the Step or Quadric function. Hence, the fuzzy adaptive Swallow Swarm Optimization (FASSO method was introduced to deal with these problems. Meanwhile, results enjoy high accuracy which are obtained by using an adaptive inertia weight and through combining two fuzzy logic systems to accurately calculate the acceleration coefficients. High speed of convergence, avoidance from falling into local extremum, and high level of error tolerance are the advantages of proposed method. The FASSO was compared with eleven of the best PSO methods and SSO in 18 benchmark functions. Finally, significant results were obtained.

  8. Cost optimal river dike design using probabilistic methods

    NARCIS (Netherlands)

    Bischiniotis, K.; Kanning, W.; Jonkman, S.N.

    2014-01-01

    This research focuses on the optimization of river dikes using probabilistic methods. Its aim is to develop a generic method that automatically estimates the failure probabilities of many river dike cross-sections and gives the one with the least cost, taking into account the boundary conditions and

  9. Multiplier methods for optimization problems with Lipschitzian derivatives

    Science.gov (United States)

    Izmailov, A. F.; Kurennoy, A. S.

    2012-12-01

    Optimization problems for which the objective function and the constraints have locally Lipschitzian derivatives but are not assumed to be twice differentiable are examined. For such problems, analyses of the local convergence and the convergence rate of the multiplier (or the augmented Lagrangian) method and the linearly constraint Lagrangian method are given.

  10. The piecewise constant method in gait design through optimization

    Institute of Scientific and Technical Information of China (English)

    Yizhen Wei

    2014-01-01

    The objective of this paper is to introduce the piecewise constant method in gait design of a planar, under actuated, five-link biped robot model and to discuss the advantages and disadvantages. The piecewise constant method transforms the dynamic optimal control problem into a static problem.

  11. An intermediate targets method for time parallelization in optimal control

    CERN Document Server

    Maday, Yvon; Riahi, Kamel

    2011-01-01

    In this paper, we present a method that enables to solve in parallel the Euler-Lagrange system associated with the optimal control of a parabolic equation. Our approach is based on an iterative update of a sequence of intermediate targets and gives rise independent sub-problems that can be solved in parallel. Numerical experiments show the efficiency of our method.

  12. Cost optimal river dike design using probabilistic methods

    NARCIS (Netherlands)

    Bischiniotis, K.; Kanning, W.; Jonkman, S.N.

    2014-01-01

    This research focuses on the optimization of river dikes using probabilistic methods. Its aim is to develop a generic method that automatically estimates the failure probabilities of many river dike cross-sections and gives the one with the least cost, taking into account the boundary conditions and

  13. CONIC TRUST REGION METHOD FOR LINEARLY CONSTRAINED OPTIMIZATION

    Institute of Scientific and Technical Information of China (English)

    Wen-yu Sun; Jin-yun Yuan; Ya-xiang Yuan

    2003-01-01

    In this paper we present a trust region method of conic model for linearly constrainedoptimization problems. We discuss trust region approaches with conic model subproblems.Some equivalent variation properties and optimality conditions are given. A trust regionalgorithm based on conic model is constructed. Global convergence of the method isestablished.

  14. A Combined Method in Parameters Optimization of Hydrocyclone

    Directory of Open Access Journals (Sweden)

    Jing-an Feng

    2016-01-01

    Full Text Available To achieve efficient separation of calcium hydroxide and impurities in carbide slag by using hydrocyclone, the physical granularity property of carbide slag, hydrocyclone operation parameters for slurry concentration, and the slurry velocity inlet are designed to be optimized. The optimization methods are combined with the Design of Experiment (DOE method and the Computational Fluid Dynamics (CFD method. Based on Design Expert software, the central composite design (CCD with three factors and five levels amounting to five groups of 20 test responses was constructed, and the experiments were performed by numerical simulation software FLUENT. Through the analysis of variance deduced from numerical simulation experiment results, the regression equations of pressure drop, overflow concentration, purity, and separation efficiencies of two solid phases were, respectively, obtained. The influences of factors were analyzed by the responses, respectively. Finally, optimized results were obtained by the multiobjective optimization method through the Design Expert software. Based on the optimized conditions, the validation test by numerical simulation and separation experiment were separately proceeded. The results proved that the combined method could be efficiently used in studying the hydrocyclone and it has a good performance in application engineering.

  15. Optimization of digital breast tomosynthesis using the Taguchi method

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Taewon; Min, Jonghwan; Cho, Seungryong [KAIST, Daejeon (Korea, Republic of). Dept. of Nuclear and Quantum Engineering

    2011-07-01

    Digital breast tomosynthesis (DBT) has been demonstrated to be a promising technique in early breast cancer detection. The DBT performance is generally affected by many factors including scanning parameters such as limited angle and limited dose value, and reconstruction method. Many investigators have studied the effects of those factors on image quality of DBT, and optimized the factors accordingly. The suggested scanning parameters, however, vary widely among the investigators. Optimization in DBT can be challenging partly due to the large number of parameters that are involved in the optimization, and also due to diverse imaging tasks under consideration. In this work, we propose an optimization method for DBT based on the Taguchi design-of-experiment method. It should be noted that we are not searching for a universal, optimum DBT technique, which we believe is very difficult if not impossible, but instead we would like to demonstrate that the Taguchi method provides an efficient and systematic way of optimizing many parameters for a given DBT system and a given imaging task. As a preliminary, we conducted a numerical simulation study, and showed that the Taguchi method effectively selected the (near-) optimum parameters for a mass detection task. (orig.)

  16. A solution quality assessment method for swarm intelligence optimization algorithms.

    Science.gov (United States)

    Zhang, Zhaojun; Wang, Gai-Ge; Zou, Kuansheng; Zhang, Jianhua

    2014-01-01

    Nowadays, swarm intelligence optimization has become an important optimization tool and wildly used in many fields of application. In contrast to many successful applications, the theoretical foundation is rather weak. Therefore, there are still many problems to be solved. One problem is how to quantify the performance of algorithm in finite time, that is, how to evaluate the solution quality got by algorithm for practical problems. It greatly limits the application in practical problems. A solution quality assessment method for intelligent optimization is proposed in this paper. It is an experimental analysis method based on the analysis of search space and characteristic of algorithm itself. Instead of "value performance," the "ordinal performance" is used as evaluation criteria in this method. The feasible solutions were clustered according to distance to divide solution samples into several parts. Then, solution space and "good enough" set can be decomposed based on the clustering results. Last, using relative knowledge of statistics, the evaluation result can be got. To validate the proposed method, some intelligent algorithms such as ant colony optimization (ACO), particle swarm optimization (PSO), and artificial fish swarm algorithm (AFS) were taken to solve traveling salesman problem. Computational results indicate the feasibility of proposed method.

  17. Methods of optimal control choice of non-Keplerian orbits

    Science.gov (United States)

    Starinova, Olga

    2017-01-01

    The developed method of iterative optimization of interplanetary missions with the low thrust, using sequence of movement specified mathematical models and design shape spacecraft, is realized. The new articular analytical decision describing planar movement of spacecraft with solar electric propulsion is described, allowing to construct initial approach in the iterative scheme of optimization. Developed a method of modelling and optimization of interplanetary missions ballistic schemes, based on a combination of Pontryagin's maximum principle formalism conditions of transversality and methods of the mathematical programming, allowing to consider restrictions characteristic for concrete interplanetary missions. Recommendations for choice design-ballistic parameters of the interplanetary missions spacecraft, received taking into account features nuclear and solar power plant for missions on delivery of a payload to orbits of Mars, expeditions the Earth-Mars-Earth are received.

  18. Optimization method for electron beam melting and refining of metals

    Science.gov (United States)

    Donchev, Veliko; Vutova, Katia

    2014-03-01

    Pure metals and special alloys obtained by electron beam melting and refining (EBMR) in vacuum, using electron beams as a heating source, have a lot of applications in nuclear and airspace industries, electronics, medicine, etc. An analytical optimization problem for the EBMR process based on mathematical heat model is proposed. The used criterion is integral functional minimization of a partial derivative of the temperature in the metal sample. The investigated technological parameters are the electron beam power, beam radius, the metal casting velocity, etc. The optimization problem is discretized using a non-stationary heat model and corresponding adapted Pismen-Rekford numerical scheme, developed by us and multidimensional trapezional rule. Thus a discrete optimization problem is built where the criterion is a function of technological process parameters. The discrete optimization problem is heuristically solved by cluster optimization method. Corresponding software for the optimization task is developed. The proposed optimization scheme can be applied for quality improvement of the pure metals (Ta, Ti, Cu, etc.) produced by the modern and ecological-friendly EBMR process.

  19. Optimal image-fusion method based on nonsubsampled contourlet transform

    Science.gov (United States)

    Dou, Jianfang; Li, Jianxun

    2012-10-01

    The optimization of image fusion is researched. Based on the properties of nonsubsampled contourlet transform (NSCT), shift invariance, multiscale and multidirectional expansion, the fusion parameters of the multiscale decompostion scheme is optimized. In order to meet the requirement of feedback optimization, a new image fusion quality metric of image quality index normalized edge association (IQI-NEA) is built. A polynomial model is adopted to establish the relationship between the IQI_NEA metric and several decomposition levels. The optimal fusion includes four steps. First, the source images are decomposed in NSCT domain for several given levels. Second, principal component analysis is adopted to fuse the low frequency coefficients and the maximum fusion rule is utilized to fuse the high frequency coefficients to obtain the fused coefficients and the fused result is reconstructed from the obtained fused coefficients. Third, calculate the fusion quality metric IQI_NEA for the source images and fused images. Finally, the optimal fused image and optimal level are obtained through extremum properties of polynomials function. The visual and statistical results show that the proposed method has optimized the fusion performance compared to the existing fusion schemes, in terms of the visual effects and quantitative fusion evaluation indexes.

  20. Compensating Interpolation Distortion by Using New Optimized Modular Method

    CERN Document Server

    Tofighi, Mohammad; Marvasti, Farokh

    2012-01-01

    A modular method was suggested before to recover a band limited signal from the sample and hold and linearly interpolated (or, in general, an nth-order-hold) version of the regular samples. In this paper a novel approach for compensating the distortion of any interpolation based on modular method has been proposed. In this method the performance of the modular method is optimized by adding only some simply calculated coefficients. This approach causes drastic improvement in terms of signal-to-noise ratios with fewer modules compared to the classical modular method. Simulation results clearly confirm the improvement of the proposed method and also its superior robustness against additive noise.

  1. Optimization methods and silicon solar cell numerical models

    Science.gov (United States)

    Girardini, K.; Jacobsen, S. E.

    1986-01-01

    An optimization algorithm for use with numerical silicon solar cell models was developed. By coupling an optimization algorithm with a solar cell model, it is possible to simultaneously vary design variables such as impurity concentrations, front junction depth, back junction depth, and cell thickness to maximize the predicted cell efficiency. An optimization algorithm was developed and interfaced with the Solar Cell Analysis Program in 1 Dimension (SCAP1D). SCAP1D uses finite difference methods to solve the differential equations which, along with several relations from the physics of semiconductors, describe mathematically the performance of a solar cell. A major obstacle is that the numerical methods used in SCAP1D require a significant amount of computer time, and during an optimization the model is called iteratively until the design variables converge to the values associated with the maximum efficiency. This problem was alleviated by designing an optimization code specifically for use with numerically intensive simulations, to reduce the number of times the efficiency has to be calculated to achieve convergence to the optimal solution.

  2. QUADRO: A SUPERVISED DIMENSION REDUCTION METHOD VIA RAYLEIGH QUOTIENT OPTIMIZATION.

    Science.gov (United States)

    Fan, Jianqing; Ke, Zheng Tracy; Liu, Han; Xia, Lucy

    We propose a novel Rayleigh quotient based sparse quadratic dimension reduction method-named QUADRO (Quadratic Dimension Reduction via Rayleigh Optimization)-for analyzing high-dimensional data. Unlike in the linear setting where Rayleigh quotient optimization coincides with classification, these two problems are very different under nonlinear settings. In this paper, we clarify this difference and show that Rayleigh quotient optimization may be of independent scientific interests. One major challenge of Rayleigh quotient optimization is that the variance of quadratic statistics involves all fourth cross-moments of predictors, which are infeasible to compute for high-dimensional applications and may accumulate too many stochastic errors. This issue is resolved by considering a family of elliptical models. Moreover, for heavy-tail distributions, robust estimates of mean vectors and covariance matrices are employed to guarantee uniform convergence in estimating non-polynomially many parameters, even though only the fourth moments are assumed. Methodologically, QUADRO is based on elliptical models which allow us to formulate the Rayleigh quotient maximization as a convex optimization problem. Computationally, we propose an efficient linearized augmented Lagrangian method to solve the constrained optimization problem. Theoretically, we provide explicit rates of convergence in terms of Rayleigh quotient under both Gaussian and general elliptical models. Thorough numerical results on both synthetic and real datasets are also provided to back up our theoretical results.

  3. Towards Robust Designs Via Multiple-Objective Optimization Methods

    Science.gov (United States)

    Man Mohan, Rai

    2006-01-01

    evolutionary method (DE) is first used to solve a relatively difficult problem in extended surface heat transfer wherein optimal fin geometries are obtained for different safe operating base temperatures. The objective of maximizing the safe operating base temperature range is in direct conflict with the objective of maximizing fin heat transfer. This problem is a good example of achieving robustness in the context of changing operating conditions. The evolutionary method is then used to design a turbine airfoil; the two objectives being reduced sensitivity of the pressure distribution to small changes in the airfoil shape and the maximization of the trailing edge wedge angle with the consequent increase in airfoil thickness and strength. This is a relevant example of achieving robustness to manufacturing tolerances and wear and tear in the presence of other objectives.

  4. Parareal in time intermediate targets methods for optimal control problem

    CERN Document Server

    Maday, Yvon; Salomon, Julien

    2012-01-01

    In this paper, we present a method that enables solving in parallel the Euler-Lagrange system associated with the optimal control of a parabolic equation. Our approach is based on an iterative update of a sequence of intermediate targets that gives rise to independent sub-problems that can be solved in parallel. This method can be coupled with the parareal in time algorithm. Numerical experiments show the efficiency of our method.

  5. An Optimization Method for Simulator Using Probability Statistic Model

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    An optimization method was presented to be easily applied in retargetable simulator. The substance of this method is to reduce the redundant information of operation code which is caused by the variety of execution frequencies of instructions. By recoding the operation code in the loading part of simulator, times of bit comparison in identification of an instruction will get reduced. Thus the performance of the simulator will be improved. The theoretical analysis and experimental results both prove the validity of this method.

  6. METHOD OF CALCULATING THE OPTIMAL HEAT EMISSION GEOTHERMAL WELLS

    Directory of Open Access Journals (Sweden)

    A. I. Akaev

    2015-01-01

    Full Text Available This paper presents a simplified method of calculating the optimal regimes of the fountain and the pumping exploitation of geothermal wells, reducing scaling and corrosion during operation. Comparative characteristics to quantify the heat of formation for these methods of operation under the same pressure at the wellhead. The problem is solved graphic-analytical method based on a balance of pressure in the well with the heat pump. 

  7. Inversion method based on stochastic optimization for particle sizing.

    Science.gov (United States)

    Sánchez-Escobar, Juan Jaime; Barbosa-Santillán, Liliana Ibeth; Vargas-Ubera, Javier; Aguilar-Valdés, Félix

    2016-08-01

    A stochastic inverse method is presented based on a hybrid evolutionary optimization algorithm (HEOA) to retrieve a monomodal particle-size distribution (PSD) from the angular distribution of scattered light. By solving an optimization problem, the HEOA (with the Fraunhofer approximation) retrieves the PSD from an intensity pattern generated by Mie theory. The analyzed light-scattering pattern can be attributed to unimodal normal, gamma, or lognormal distribution of spherical particles covering the interval of modal size parameters 46≤α≤150. The HEOA ensures convergence to the near-optimal solution during the optimization of a real-valued objective function by combining the advantages of a multimember evolution strategy and locally weighted linear regression. The numerical results show that our HEOA can be satisfactorily applied to solve the inverse light-scattering problem.

  8. Exergetic optimization of turbofan engine with genetic algorithm method

    Energy Technology Data Exchange (ETDEWEB)

    Turan, Onder [Anadolu University, School of Civil Aviation (Turkey)], e-mail: onderturan@anadolu.edu.tr

    2011-07-01

    With the growth of passenger numbers, emissions from the aeronautics sector are increasing and the industry is now working on improving engine efficiency to reduce fuel consumption. The aim of this study is to present the use of genetic algorithms, an optimization method based on biological principles, to optimize the exergetic performance of turbofan engines. The optimization was carried out using exergy efficiency, overall efficiency and specific thrust of the engine as evaluation criteria and playing on pressure and bypass ratio, turbine inlet temperature and flight altitude. Results showed exergy efficiency can be maximized with higher altitudes, fan pressure ratio and turbine inlet temperature; the turbine inlet temperature is the most important parameter for increased exergy efficiency. This study demonstrated that genetic algorithms are effective in optimizing complex systems in a short time.

  9. Optimal mesh hierarchies in Multilevel Monte Carlo methods

    KAUST Repository

    Von Schwerin, Erik

    2016-01-08

    I will discuss how to choose optimal mesh hierarchies in Multilevel Monte Carlo (MLMC) simulations when computing the expected value of a quantity of interest depending on the solution of, for example, an Ito stochastic differential equation or a partial differential equation with stochastic data. I will consider numerical schemes based on uniform discretization methods with general approximation orders and computational costs. I will compare optimized geometric and non-geometric hierarchies and discuss how enforcing some domain constraints on parameters of MLMC hierarchies affects the optimality of these hierarchies. I will also discuss the optimal tolerance splitting between the bias and the statistical error contributions and its asymptotic behavior. This talk presents joint work with N.Collier, A.-L.Haji-Ali, F. Nobile, and R. Tempone.

  10. Investigation of Optimal Integrated Circuit Raster Image Vectorization Method

    Directory of Open Access Journals (Sweden)

    Leonas Jasevičius

    2011-03-01

    Full Text Available Visual analysis of integrated circuit layer requires raster image vectorization stage to extract layer topology data to CAD tools. In this paper vectorization problems of raster IC layer images are presented. Various line extraction from raster images algorithms and their properties are discussed. Optimal raster image vectorization method was developed which allows utilization of common vectorization algorithms to achieve the best possible extracted vector data match with perfect manual vectorization results. To develop the optimal method, vectorized data quality dependence on initial raster image skeleton filter selection was assessed.Article in Lithuanian

  11. Optimizing the atmospheric sampling sites using fuzzy mathematic methods

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A new approach applying fuzzy mathematic theorems, including the Primary Matrix Element Theorem and the Fisher ClassificationMethod, was established to solve the optimization problem of atmospheric environmental sampling sites. According to its basis, an applicationin the optimization of sampling sites in the atmospheric environmental monitoring was discussed. The method was proven to be suitable andeffective. The results were admitted and applied by the Environmental Protection Bureau (EPB) of many cities of China. A set of computersoftware of this approach was also completely compiled and used.

  12. Unconstrained steepest descent method for multicriteria optimization on Riemmanian manifolds

    CERN Document Server

    Bento, G C; Oliveira, P R

    2010-01-01

    In this paper we present a steepest descent method with Armijo's rule for multicriteria optimization in the Riemannian context. The well definedness of the sequence generated by the method is guaranteed. Under mild assumptions on the multicriteria function, we prove that each accumulation point (if they exist) satisfies first-order necessary conditions for Pareto optimality. Moreover, assuming quasi-convexity of the multicriteria function and non-negative curvature of the Riemannian manifold, we prove full convergence of the sequence to a Pareto critical.

  13. Thickness optimization of fiber reinforced laminated composites using the discrete material optimization method

    DEFF Research Database (Denmark)

    Sørensen, Søren Nørgaard; Lund, Erik

    2012-01-01

    This work concerns a novel large-scale multi-material topology optimization method for simultaneous determination of the optimum variable integer thickness and fiber orientation throughout laminate structures with fixed outer geometries while adhering to certain manufacturing constraints. The con......This work concerns a novel large-scale multi-material topology optimization method for simultaneous determination of the optimum variable integer thickness and fiber orientation throughout laminate structures with fixed outer geometries while adhering to certain manufacturing constraints....... The conceptual combinatorial/integer problem is relaxed to a continuous problem and solved on basis of the so-called Discrete Material Optimization method, explicitly including the manufacturing constraints as linear constraints....

  14. Methods of centers and methods of feasible directions for the solution of optimal control problems.

    Science.gov (United States)

    Polak, E.; Mukai, H.; Pironneau, O.

    1971-01-01

    Demonstration of the applicability of methods of centers and of methods of feasible directions to optimal control problems. Presented experimental results show that extensions of Frank-Wolfe (1956), Zoutendijk (1960), and Pironneau-Polak (1971) algorithms for nonlinear programming problems can be quite efficient in solving optimal control problems.

  15. Nozzle Mounting Method Optimization Based on Robot Kinematic Analysis

    Science.gov (United States)

    Chen, Chaoyue; Liao, Hanlin; Montavon, Ghislain; Deng, Sihao

    2016-08-01

    Nowadays, the application of industrial robots in thermal spray is gaining more and more importance. A desired coating quality depends on factors such as a balanced robot performance, a uniform scanning trajectory and stable parameters (e.g. nozzle speed, scanning step, spray angle, standoff distance). These factors also affect the mass and heat transfer as well as the coating formation. Thus, the kinematic optimization of all these aspects plays a key role in order to obtain an optimal coating quality. In this study, the robot performance was optimized from the aspect of nozzle mounting on the robot. An optimized nozzle mounting for a type F4 nozzle was designed, based on the conventional mounting method from the point of view of robot kinematics validated on a virtual robot. Robot kinematic parameters were obtained from the simulation by offline programming software and analyzed by statistical methods. The energy consumptions of different nozzle mounting methods were also compared. The results showed that it was possible to reasonably assign the amount of robot motion to each axis during the process, so achieving a constant nozzle speed. Thus, it is possible optimize robot performance and to economize robot energy.

  16. Optimization of Moving Bed Biofilm ReactorUsing Taguchi Method

    Directory of Open Access Journals (Sweden)

    R Nabizadeh Nodehi

    2009-07-01

    Full Text Available "n "nBackgrounds and Objectives: in recent years, mobile bed biological reactors have been used progressively for municipal and industrial wastewaters treatment. Dissented experiment is a trial that significant changes will accrue for influent variables in the process, and generally used for identification of the effective factors and optimization of the process. The scope of this study was determination of the optimized conditions for the MBBR process by using of Taguchi method. "nMaterials and Methods: Reactor start up was done by using of the recycled activated sludge from Ahwaz wastewater treatment plant. After that and passing the acclimation period, with hydraulic residence time equal to 9 hours matched for 1000, 2000 and 3000 mg/l based on COD respectively, for optimization determination of the acclimated microbial growth, the variables change (pH, nitrogen source, chemical oxygen demand and salinity were determined in 9 steps, and all of the results were analyzed by Qualitek -4 (w32b."nResults:In this study, organic load removal based on COD was 97% and best optimized condition for MBBR were (inf. COD=1000 mg/l, pH= 8, salinity = 5% and the Nitrogen source= NH4CL"nConclusion: Based on our finding, we may conclude that Taguchi method is on of the appropriate procedure in determination the optimized condition for increasing removal efficiency of MBBR.

  17. Colorimetric visualization of tin corrosion: A method for early stage corrosion detection on printed circuit boards

    DEFF Research Database (Denmark)

    Verdingovas, Vadimas; Jellesen, Morten Stendahl; Ambat, Rajan

    2017-01-01

    A majority of printed circuit board surfaces are covered with tin, therefore tin corrosion under humid conditions and movement of tin ions under the influence of an electric field plays an important role in the corrosion failure development. Tracking tin corrosion products spread on the printed...... a colorimetric tin ion indicator applied as a gel. The examples provided in this paper include visualization of corrosion caused by weak organic acids found in solder fluxes, corrosion profiling on the PCBAs after climatic device level testing, and failure analysis of field returns....

  18. A method for optimizing the performance of buildings

    DEFF Research Database (Denmark)

    Pedersen, Frank

    2007-01-01

    This thesis describes a method for optimizing the performance of buildings. Design decisions made in early stages of the building design process have a significant impact on the performance of buildings, for instance, the performance with respect to the energy consumption, economical aspects......, and the indoor environment. The method is intended for supporting design decisions for buildings, by combining methods for calculating the performance of buildings with numerical optimization methods. The method is able to find optimum values of decision variables representing different features of the building......, such as its shape, the amount and type of windows used, and the amount of insulation used in the building envelope. The parties who influence design decisions for buildings, such as building owners, building users, architects, consulting engineers, contractors, etc., often have different and to some extent...

  19. How to optimize the drop plate method for enumerating bacteria.

    Science.gov (United States)

    Herigstad, B; Hamilton, M; Heersink, J

    2001-03-01

    The drop plate (DP) method can be used to determine the number of viable suspended bacteria in a known beaker volume. The drop plate method has some advantages over the spread plate (SP) method. Less time and effort are required to dispense the drops onto an agar plate than to spread an equivalent total sample volume into the agar. By distributing the sample in drops, colony counting can be done faster and perhaps more accurately. Even though it has been present in the laboratory for many years, the drop plate method has not been standardized. Some technicians use 10-fold dilutions, others use twofold. Some technicians plate a total volume of 0.1 ml, others plate 0.2 ml. The optimal combination of such factors would be useful to know when performing the drop plate method. This investigation was conducted to determine (i) the standard deviation of the bacterial density estimate, (ii) the cost of performing the drop plate procedure, (iii) the optimal drop plate design, and (iv) the advantages of the drop plate method in comparison to the standard spread plate method. The optimal design is the combination of factor settings that achieves the smallest standard deviation for a fixed cost. Computer simulation techniques and regression analysis were used to express the standard deviation as a function of the beaker volume, dilution factor, and volume plated. The standard deviation expression is also applicable to the spread plate method.

  20. Some optimal iterative methods and their with memory variants

    Directory of Open Access Journals (Sweden)

    F. Soleymani

    2013-07-01

    Full Text Available Based on the fourth-order method of Liu et al. [10], eighth-order three-step iterative methods without memory, which are totally free from derivative calculation and reach the optimal efficiency index are presented. The extension of one of the methods for multiple zeros without the knowledge of multiplicity is presented. Further accelerations will be provided through the concept of with memory iteration methods. Moreover, it is shown by way of illustration that the novel methods are useful on a series of relevant numerical problems when high precision computing is required.

  1. Trajectory Optimization Using Adjoint Method and Chebyshev Polynomial Approximation for Minimizing Fuel Consumption During Climb

    Science.gov (United States)

    Nguyen, Nhan T.; Hornby, Gregory; Ishihara, Abe

    2013-01-01

    This paper describes two methods of trajectory optimization to obtain an optimal trajectory of minimum-fuel- to-climb for an aircraft. The first method is based on the adjoint method, and the second method is based on a direct trajectory optimization method using a Chebyshev polynomial approximation and cubic spine approximation. The approximate optimal trajectory will be compared with the adjoint-based optimal trajectory which is considered as the true optimal solution of the trajectory optimization problem. The adjoint-based optimization problem leads to a singular optimal control solution which results in a bang-singular-bang optimal control.

  2. Optimization of MIMO Systems Capacity Using Large Random Matrix Methods

    Directory of Open Access Journals (Sweden)

    Philippe Loubaton

    2012-11-01

    Full Text Available This paper provides a comprehensive introduction of large random matrix methods for input covariance matrix optimization of mutual information of MIMO systems. It is first recalled informally how large system approximations of mutual information can be derived. Then, the optimization of the approximations is discussed, and important methodological points that are not necessarily covered by the existing literature are addressed, including the strict concavity of the approximation, the structure of the argument of its maximum, the accuracy of the large system approach with regard to the number of antennas, or the justification of iterative water-filling optimization algorithms. While the existing papers have developed methods adapted to a specific model, this contribution tries to provide a unified view of the large system approximation approach.

  3. Control and Optimization Methods for Electric Smart Grids

    CERN Document Server

    Ilić, Marija

    2012-01-01

    Control and Optimization Methods for Electric Smart Grids brings together leading experts in power, control and communication systems,and consolidates some of the most promising recent research in smart grid modeling,control and optimization in hopes of laying the foundation for future advances in this critical field of study. The contents comprise eighteen essays addressing wide varieties of control-theoretic problems for tomorrow’s power grid. Topics covered include: Control architectures for power system networks with large-scale penetration of renewable energy and plug-in vehicles Optimal demand response New modeling methods for electricity markets Control strategies for data centers Cyber-security Wide-area monitoring and control using synchronized phasor measurements. The authors present theoretical results supported by illustrative examples and practical case studies, making the material comprehensible to a wide audience. The results reflect the exponential transformation that today’s grid is going...

  4. Optimal Joint Multiple Resource Allocation Method for Cloud Computing Environments

    CERN Document Server

    Kuribayashi, Shin-ichi

    2011-01-01

    Cloud computing is a model for enabling convenient, on-demand network access to a shared pool of configurable computing resources. To provide cloud computing services economically, it is important to optimize resource allocation under the assumption that the required resource can be taken from a shared resource pool. In addition, to be able to provide processing ability and storage capacity, it is necessary to allocate bandwidth to access them at the same time. This paper proposes an optimal resource allocation method for cloud computing environments. First, this paper develops a resource allocation model of cloud computing environments, assuming both processing ability and bandwidth are allocated simultaneously to each service request and rented out on an hourly basis. The allocated resources are dedicated to each service request. Next, this paper proposes an optimal joint multiple resource allocation method, based on the above resource allocation model. It is demonstrated by simulation evaluation that the p...

  5. 低轨卫星系统星载多波束天线点波束设计及优化%Spot -beam Design and Optimization of On- board Multi -beam Antenna for LEO Satellite Systems

    Institute of Scientific and Technical Information of China (English)

    张旭; 吴潜

    2009-01-01

    星载多波束天线具有广阔的应用前景,尤其适合应用于低轨卫星系统.讨论了星载多波束天线点波束设计的方法,为平衡点波束各覆盖区域的接收增益,借鉴最优化理论思想,提出了一种点波束设计的方法,以全球星系统为例进行分析,结果表明该方法较典型的点波束设计方法具有更高的满意度.%Muhi - beam antenna is widely used in low earth orbit(LEO) satellite systems. Spot - beam de-sign of on - board multi - beam antenna is discussed, an optimized method adopting optimization theory for spot -beam design is proposed to balance the receiving gain of each spot -beam covering area, analysis of the optimized method for Globalstar system is given, and higher satisfaction of the proposed method is proved.

  6. Reliability-Based Shape Optimization using Stochastic Finite Element Methods

    DEFF Research Database (Denmark)

    Enevoldsen, Ib; Sørensen, John Dalsgaard; Sigurdsson, G.

    1991-01-01

    Application of first-order reliability methods FORM (see Madsen, Krenk & Lind [8)) in structural design problems has attracted growing interest in recent years, see e.g. Frangopol [4), Murotsu, Kishi, Okada, Yonezawa & Taguchi [9) and Sørensen [14). In probabilistically based optimal design...

  7. Practical inventory routing: A problem definition and an optimization method

    CERN Document Server

    Geiger, Martin Josef

    2011-01-01

    The global objective of this work is to provide practical optimization methods to companies involved in inventory routing problems, taking into account this new type of data. Also, companies are sometimes not able to deal with changing plans every period and would like to adopt regular structures for serving customers.

  8. Optimal Variational Asymptotic Method for Nonlinear Fractional Partial Differential Equations.

    Science.gov (United States)

    Baranwal, Vipul K; Pandey, Ram K; Singh, Om P

    2014-01-01

    We propose optimal variational asymptotic method to solve time fractional nonlinear partial differential equations. In the proposed method, an arbitrary number of auxiliary parameters γ 0, γ 1, γ 2,… and auxiliary functions H 0(x), H 1(x), H 2(x),… are introduced in the correction functional of the standard variational iteration method. The optimal values of these parameters are obtained by minimizing the square residual error. To test the method, we apply it to solve two important classes of nonlinear partial differential equations: (1) the fractional advection-diffusion equation with nonlinear source term and (2) the fractional Swift-Hohenberg equation. Only few iterations are required to achieve fairly accurate solutions of both the first and second problems.

  9. An Optimal Calibration Method for a MEMS Inertial Measurement Unit

    Directory of Open Access Journals (Sweden)

    Bin Fang

    2014-02-01

    Full Text Available An optimal calibration method for a micro-electro-mechanical inertial measurement unit (MIMU is presented in this paper. The accuracy of the MIMU is highly dependent on calibration to remove the deterministic errors of systematic errors, which also contain random errors. The overlapping Allan variance is applied to characterize the types of random error terms in the measurements. The calibration model includes package misalignment error, sensor-to-sensor misalignment error and bias, and a scale factor is built. The new concept of a calibration method, which includes a calibration scheme and a calibration algorithm, is proposed. The calibration scheme is designed by D-optimal and the calibration algorithm is deduced by a Kalman filter. In addition, the thermal calibration is investigated, as the bias and scale factor varied with temperature. The simulations and real tests verify the effectiveness of the proposed calibration method and show that it is better than the traditional method.

  10. A method for optimizing the performance of buildings

    Energy Technology Data Exchange (ETDEWEB)

    Pedersen, Frank

    2006-07-01

    This thesis describes a method for optimizing the performance of buildings. Design decisions made in early stages of the building design process have a significant impact on the performance of buildings, for instance, the performance with respect to the energy consumption, economical aspects, and the indoor environment. The method is intended for supporting design decisions for buildings, by combining methods for calculating the performance of buildings with numerical optimization methods. The method is able to find optimum values of decision variables representing different features of the building, such as its shape, the amount and type of windows used, and the amount of insulation used in the building envelope. The parties who influence design decisions for buildings, such as building owners, building users, architects, consulting engineers, contractors, etc., often have different and to some extent conflicting requirements to buildings. For instance, the building owner may be more concerned about the cost of constructing the building, rather than the quality of the indoor climate, which is more likely to be a concern of the building user. In order to support the different types of requirements made by decision-makers for buildings, an optimization problem is formulated, intended for representing a wide range of design decision problems for buildings. The problem formulation involves so-called performance measures, which can be calculated with simulation software for buildings. For instance, the annual amount of energy required by the building, the cost of constructing the building, and the annual number of hours where overheating occurs, can be used as performance measures. The optimization problem enables the decision-makers to specify many different requirements to the decision variables, as well as to the performance of the building. Performance measures can for instance be required to assume their minimum or maximum value, they can be subjected to upper or

  11. NOVEL METHOD SOLVING NUMERICAL INSTABILITIES IN TOPOLOGY OPTIMIZATION

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Numerical instabilities are often encountered in FE solution of continuum topology optimization. The essence of the numerical instabilities is given from the inverse partial differential equation (PDE) point of view. On the basis of the strict mathematical theory, a novel method, named as window filter and multi-grid method, which solves the numerical instabilities, is proposed. Convergent analyses and a numerical example are presented.

  12. Optimization of methods for detecting norovirus on various fruit.

    Science.gov (United States)

    Kim, Hee-Yeon; Kwak, In-Shin; Hwang, In-Gyun; Ko, GwangPyo

    2008-11-01

    Methods for detecting norovirus (NoV) in food are crucial for investigation and prevention of outbreaks caused by NoV-contaminated food. However, current NoV detection methods have not been well examined or optimized. In this study, the effectiveness of various methods for eluting NoV from various fruit, concentrating the virus using polyethylene glycol (PEG), and extracting the viral RNA for subsequent assay by RT-PCR was optimized. First, six different buffers previously described for eluting NoV from fruit surfaces were evaluated. A known amount of NoV was spiked onto the surface of grapes, strawberries, and raspberries, and the virus was recovered with distilled water, 0.05 M glycine-0.14 M NaCl (pH 7.5), 2.9% tryptose phosphate broth-6% glycine, 100 mM Tris-HCl (pH 9.5), 50 mM glycine-50 mM MgCl(2) (pH 9.5), or 3% beef extract. Quantitation of the recovered virus using RT-PCR revealed that the most effective elution buffer was 3% beef extract. Secondly, to optimize a method for concentrating the recovered NoV, the key parameters of PEG precipitation, a typical method for concentrating enteric virus, were investigated. The influence of PEG molecular weight and the duration and temperature of the precipitation procedure were examined. NoV was concentrated most efficiently by precipitation when PEG (10,000) was used for 4h at room temperature. Finally, five different methods for nucleic acid extraction were evaluated. Among RNA extraction methods examined, QIAamp Viral RNA Mini kit showed the best recovery efficiency. Using the optimized method, approximately 6-80% of the seeded NoV was recovered from the various fruit.

  13. METHODS FOR DETERMINATION AND OPTIMIZATION OF LOGISTICS COSTS

    OpenAIRE

    Mihaela STET

    2016-01-01

    The paper is dealing with the problems of logistics costs, highlighting some methods for estimation and determination of specific costs for different transport modes in freight distribution. There are highlighted, besides costs of transports, the other costs in supply chain, as well as costing methods used in logistics activities. In this context, there are also revealed some optimization means of transport costs in logistics chain.

  14. Apparatus and methods for manipulation and optimization of biological systems

    Science.gov (United States)

    Ho, Chih-Ming (Inventor); Wong, Pak Kin (Inventor); Sun, Ren (Inventor); Yu, Fuqu (Inventor)

    2012-01-01

    The invention provides systems and methods for manipulating, e.g., optimizing and controlling, biological systems, e.g., for eliciting a more desired biological response of biological sample, such as a tissue, organ, and/or a cell. In one aspect, systems and methods of the invention operate by efficiently searching through a large parametric space of stimuli and system parameters to manipulate, control, and optimize the response of biological samples sustained in the system, e.g., a bioreactor. In alternative aspects, systems include a device for sustaining cells or tissue samples, one or more actuators for stimulating the samples via biochemical, electromagnetic, thermal, mechanical, and/or optical stimulation, one or more sensors for measuring a biological response signal of the samples resulting from the stimulation of the sample. In one aspect, the systems and methods of the invention use at least one optimization algorithm to modify the actuator's control inputs for stimulation, responsive to the sensor's output of response signals. The compositions and methods of the invention can be used, e.g., to for systems optimization of any biological manufacturing or experimental system, e.g., bioreactors for proteins, e.g., therapeutic proteins, polypeptides or peptides for vaccines, and the like, small molecules (e.g., antibiotics), polysaccharides, lipids, and the like. Another use of the apparatus and methods includes combination drug therapy, e.g. optimal drug cocktail, directed cell proliferations and differentiations, e.g. in tissue engineering, e.g. neural progenitor cells differentiation, and discovery of key parameters in complex biological systems.

  15. Robust fluence map optimization via alternating direction method of multipliers with empirical parameter optimization

    Science.gov (United States)

    Gao, Hao

    2016-04-01

    For the treatment planning during intensity modulated radiation therapy (IMRT) or volumetric modulated arc therapy (VMAT), beam fluence maps can be first optimized via fluence map optimization (FMO) under the given dose prescriptions and constraints to conformally deliver the radiation dose to the targets while sparing the organs-at-risk, and then segmented into deliverable MLC apertures via leaf or arc sequencing algorithms. This work is to develop an efficient algorithm for FMO based on alternating direction method of multipliers (ADMM). Here we consider FMO with the least-square cost function and non-negative fluence constraints, and its solution algorithm is based on ADMM, which is efficient and simple-to-implement. In addition, an empirical method for optimizing the ADMM parameter is developed to improve the robustness of the ADMM algorithm. The ADMM based FMO solver was benchmarked with the quadratic programming method based on the interior-point (IP) method using the CORT dataset. The comparison results suggested the ADMM solver had a similar plan quality with slightly smaller total objective function value than IP. A simple-to-implement ADMM based FMO solver with empirical parameter optimization is proposed for IMRT or VMAT.

  16. An hp symplectic pseudospectral method for nonlinear optimal control

    Science.gov (United States)

    Peng, Haijun; Wang, Xinwei; Li, Mingwu; Chen, Biaosong

    2017-01-01

    An adaptive symplectic pseudospectral method based on the dual variational principle is proposed and is successfully applied to solving nonlinear optimal control problems in this paper. The proposed method satisfies the first order necessary conditions of continuous optimal control problems, also the symplectic property of the original continuous Hamiltonian system is preserved. The original optimal control problem is transferred into a set of nonlinear equations which can be solved easily by Newton-Raphson iterations, and the Jacobian matrix is found to be sparse and symmetric. The proposed method, on one hand, exhibits exponent convergence rates when the number of collocation points are increasing with the fixed number of sub-intervals; on the other hand, exhibits linear convergence rates when the number of sub-intervals is increasing with the fixed number of collocation points. Furthermore, combining with the hp method based on the residual error of dynamic constraints, the proposed method can achieve given precisions in a few iterations. Five examples highlight the high precision and high computational efficiency of the proposed method.

  17. Chebyshev-Legendre method for discretizing optimal control problems

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wen; MA He-ping

    2009-01-01

    In this paper, a numerical method for solving the optimal control (OC) problems is presented. The method is enlightened by the Chebyshev-Legendre (CL) method for solving the partial differential equations (PDEs). The Legen-dre expansions are used to approximate both the control and the state functions. The constraints are discretized over the Chebyshev-Gauss-Lobatto (CGL) collocation points. A Legendre technique is used to approximate the integral involved in the performance index. The OC problem is changed into an equivalent nonlinear programming problem which is directly solved. The fast Legendre transform is employed to reduce the computation time. Several further illustrative examples demonstrate the efficiency of the proposed method.

  18. An ant colony optimization method for generalized TSP problem

    Institute of Scientific and Technical Information of China (English)

    Jinhui Yang; Xiaohu Shi; Maurizio Marchese; Yanchun Liang

    2008-01-01

    Focused on a variation of the euclidean traveling salesman problem (TSP), namely, the generalized traveling salesman problem (GTSP), this paper extends the ant colony optimization method from TSP to this field. By considering the group influence, an improved method is further improved. To avoid locking into local minima, a mutation process and a local searching technique are also introduced into this method. Numerical results show that the proposed method can deal with the GTSP problems fairly well, and the developed mutation process and local search technique are effective.

  19. Optimization method for quantitative calculation of clay minerals in soil

    Indian Academy of Sciences (India)

    Libo Hao; Qiaoqiao Wei; Yuyan Zhao; Zilong Lu; Xinyun Zhao

    2015-04-01

    Determination of types and amounts for clay minerals in soil are important in environmental, agricultural, and geological investigations. Many reliable methods have been established to identify clay mineral types. However, no reliable method for quantitative analysis of clay minerals has been established so far. In this study, an attempt was made to propose an optimization method for the quantitative determination of clay minerals in soil based on bulk chemical composition data. The fundamental principles and processes of the calculation are elucidated. Some samples were used for reliability verification of the method and the results prove the simplicity and efficacy of the approach.

  20. Method of Fire Image Identification Based on Optimization Theory

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In view of some distinctive characteristics of the early-stage flame image, a corresponding method of characteristic extraction is presented. Also introduced is the application of the improved BP algorithm based on the optimization theory to identifying fire image characteristics. First the optimization of BP neural network adopting Levenberg-Marquardt algorithm with the property of quadratic convergence is discussed, and then a new system of fire image identification is devised. Plenty of experiments and field tests have proved that this system can detect the early-stage fire flame quickly and reliably.

  1. A New Method for Optimal Harmonic Meter Placement

    Directory of Open Access Journals (Sweden)

    A. Ketabi

    2008-01-01

    Full Text Available In this research, a new method based on Singular Value Decomposition (SVD is proposed to solve the problem of optimal placement of meters for static estimation of harmonic sources in a power system. Also, the Binary Genetic Algorithm (BGA is used to solve the problem of optimization. IEEE 14-bus test system is provided to validate the measurement placement algorithm. It has been observed that the quality of estimation is improved and the Number of Observable Variable (NOV is increased. Moreover, the BGA-based meter placement strategy yields the same solution as obtained from the complete enumeration technique but in shorter time.

  2. Optimal Allocation of Power-Electronic Interfaced Wind Turbines Using a Genetic Algorithm - Monte Carlo Hybrid Optimization Method

    DEFF Research Database (Denmark)

    Chen, Peiyuan; Siano, Pierluigi; Chen, Zhe;

    2010-01-01

    limit requirements. The method combines the Genetic Algorithm (GA), gradient-based constrained nonlinear optimization algorithm and sequential Monte Carlo simulation (MCS). The GA searches for the optimal locations and capacities of WTs. The gradient-based optimization finds the optimal power factor...

  3. Optimal Allocation of Power-Electronic Interfaced Wind Turbines Using a Genetic Algorithm - Monte Carlo Hybrid Optimization Method

    DEFF Research Database (Denmark)

    Chen, Peiyuan; Siano, Pierluigi; Chen, Zhe

    2010-01-01

    limit requirements. The method combines the Genetic Algorithm (GA), gradient-based constrained nonlinear optimization algorithm and sequential Monte Carlo simulation (MCS). The GA searches for the optimal locations and capacities of WTs. The gradient-based optimization finds the optimal power factor...

  4. The construction of optimal stated choice experiments theory and methods

    CERN Document Server

    Street, Deborah J

    2007-01-01

    The most comprehensive and applied discussion of stated choice experiment constructions available The Construction of Optimal Stated Choice Experiments provides an accessible introduction to the construction methods needed to create the best possible designs for use in modeling decision-making. Many aspects of the design of a generic stated choice experiment are independent of its area of application, and until now there has been no single book describing these constructions. This book begins with a brief description of the various areas where stated choice experiments are applicable, including marketing and health economics, transportation, environmental resource economics, and public welfare analysis. The authors focus on recent research results on the construction of optimal and near-optimal choice experiments and conclude with guidelines and insight on how to properly implement these results. Features of the book include: Construction of generic stated choice experiments for the estimation of main effects...

  5. Immune clonal selection optimization method with combining mutation strategies

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In artificial immune optimization algorithm, the mutation of immune cells has been considered as the key operator that determines the algorithm performance. Traditional immune optimization algorithms have used a single mutation operator, typically a Gaussian. Using a variety of mutation operators that can be combined during evolution to generate different probability density function could hold the potential for producing better solutions with less computational effort. In view of this, a linear combination mutation operator of Gaussian and Cauchy mutation is presented in this paper, and a novel clonal selection optimization method based on clonal selection principle is proposed also. The simulation results show the combining mutation strategy can obtain the same performance as the best of pure strategies or even better in some cases.

  6. A Survey of Methods for Gas-Lift Optimization

    Directory of Open Access Journals (Sweden)

    Kashif Rashid

    2012-01-01

    Full Text Available This paper presents a survey of methods and techniques developed for the solution of the continuous gas-lift optimization problem over the last two decades. These range from isolated single-well analysis all the way to real-time multivariate optimization schemes encompassing all wells in a field. While some methods are clearly limited due to their neglect of treating the effects of inter-dependent wells with common flow lines, other methods are limited due to the efficacy and quality of the solution obtained when dealing with large-scale networks comprising hundreds of difficult to produce wells. The aim of this paper is to provide an insight into the approaches developed and to highlight the challenges that remain.

  7. Application of Taguchi method in optimization of cervical ring cage.

    Science.gov (United States)

    Yang, Kai; Teo, Ee-Chon; Fuss, Franz Konstantin

    2007-01-01

    The Taguchi method is a statistical approach to overcome the limitation of the factorial and fractional factorial experiments by simplifying and standardizing the fractional factorial design. The objective of the current study is to illustrate the procedures and strengths of the Taguchi method in biomechanical analysis by using a case study of a cervical ring cage optimization. A three-dimensional finite element (FE) model of C(5)-C(6) with a generic cervical ring cage inserted was modelled. Taguchi method was applied in the optimization of the cervical ring cage in material property and dimensions for producing the lowest stress on the endplate to reduce the risk of cage subsidence, as in the following steps: (1) establishment of objective function; (2) determination of controllable factors and their levels; (3) identification of uncontrollable factors and test conditions; (4) design of Taguchi crossed array layout; (5) execution of experiments according to trial conditions; (6) analysis of results; (7) determination of optimal run; (8) confirmation of optimum run. The results showed that a cage with larger width, depth and wall thickness can produce the lower von Mises stress under various conditions. The contribution of implant materials is found trivial. The current case study illustrates that the strengths of the Taguchi method lie in (1) consistency in experimental design and analysis; (2) reduction of time and cost of experiments; (3) robustness of performance with removing the noise factors. The Taguchi method will have a great potential application in biomechanical field when factors of the issues are at discrete level.

  8. A method for optimizing the performance of buildings

    Energy Technology Data Exchange (ETDEWEB)

    Pedersen, Frank

    2006-07-01

    This thesis describes a method for optimizing the performance of buildings. Design decisions made in early stages of the building design process have a significant impact on the performance of buildings, for instance, the performance with respect to the energy consumption, economical aspects, and the indoor environment. The method is intended for supporting design decisions for buildings, by combining methods for calculating the performance of buildings with numerical optimization methods. The method is able to find optimum values of decision variables representing different features of the building, such as its shape, the amount and type of windows used, and the amount of insulation used in the building envelope. The parties who influence design decisions for buildings, such as building owners, building users, architects, consulting engineers, contractors, etc., often have different and to some extent conflicting requirements to buildings. For instance, the building owner may be more concerned about the cost of constructing the building, rather than the quality of the indoor climate, which is more likely to be a concern of the building user. In order to support the different types of requirements made by decision-makers for buildings, an optimization problem is formulated, intended for representing a wide range of design decision problems for buildings. The problem formulation involves so-called performance measures, which can be calculated with simulation software for buildings. For instance, the annual amount of energy required by the building, the cost of constructing the building, and the annual number of hours where overheating occurs, can be used as performance measures. The optimization problem enables the decision-makers to specify many different requirements to the decision variables, as well as to the performance of the building. Performance measures can for instance be required to assume their minimum or maximum value, they can be subjected to upper or

  9. Direct trajectory optimization based on a mapped Chebyshev pseudospectral method

    Institute of Scientific and Technical Information of China (English)

    Guo Xiao; Zhu Ming

    2013-01-01

    In view of generating optimal trajectories of Bolza problems,standard Chebyshev pseudospectral (PS) method makes the points' accumulation near the extremities and rarefaction of nodes close to the center of interval,which causes an ill-condition of differentiation matrix and an oscillation of the optimal solution.For improvement upon the difficulties,a mapped Chebyshev pseudospectral method is proposed.A conformal map is applied to Chebyshev points to move the points closer to equidistant nodes.Condition number and spectral radius of differentiation matrices from both methods are presented to show the improvement.Furthermore,the modification keeps the Chebyshev pseudospectral method's advantage,the spectral convergence rate.Based on three numerical examples,a comparison of the execution time,convergence and accuracy is presented among the standard Chebyshev pseudospectral method,other collocation methods and the proposed one.In one example,the error of results from mapped Chebyshev pseudospectral method is reduced to 5% of that from standard Chebyshev pseudospectral method.

  10. An efficient method for multiobjective optimal control and optimal control subject to integral constraints

    CERN Document Server

    Kumar, Ajeet

    2009-01-01

    We introduce a new and efficient numerical method for multicriterion optimal control and single criterion optimal control under integral constraints. The approach is based on extending the state space to include information on a "budget" remaining to satisfy each constraint; the augmented Hamilton-Jacobi-Bellman PDE is then solved numerically. The efficiency of our approach hinges on the causality in that PDE, i.e., the monotonicity of characteristic curves in one of the newly added dimensions. A semi-Lagrangian "marching" method is used to approximate the discontinuous viscosity solution efficiently. We compare this to a recently introduced "weighted sum" based algorithm for the same problem. We illustrate our method using examples from flight path planning and robotic navigation in the presence of friendly and adversarial observers.

  11. First-principle optimal local pseudopotentials construction via optimized effective potential method

    Science.gov (United States)

    Mi, Wenhui; Zhang, Shoutao; Wang, Yanchao; Ma, Yanming; Miao, Maosheng

    2016-04-01

    The local pseudopotential (LPP) is an important component of orbital-free density functional theory, a promising large-scale simulation method that can maintain information on a material's electron state. The LPP is usually extracted from solid-state density functional theory calculations, thereby it is difficult to assess its transferability to cases involving very different chemical environments. Here, we reveal a fundamental relation between the first-principles norm-conserving pseudopotential (NCPP) and the LPP. On the basis of this relationship, we demonstrate that the LPP can be constructed optimally from the NCPP for a large number of elements using the optimized effective potential method. Specially, our method provides a unified scheme for constructing and assessing the LPP within the framework of first-principles pseudopotentials. Our practice reveals that the existence of a valid LPP with high transferability may strongly depend on the element.

  12. A method of constructing a database-free optimal dynamical system and a global optimal dynamical system

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    In this paper, to overcome the drawbacks of POT which minimize the reminder, not only the optimal functional with minimal residual is put forward, but also the method of global optimization is used. Under the condition of large reminder, the optimal bases can also be obtained through the method of POTres without the approaching of initial conditions. In addition, compared with local optimization, the advantage of global optimization is remarkable. On the one hand, we can expect that the dynamical system based on the global optimal bases will include more information than the ones based on the local optimal bases, since the global optimal bases are much more precise than the local optimal bases. On the other hand, from the point of view of error, the global optimal bases are independent of the choice of the object functional and the initial bases.

  13. A method for unified optimization of systems and controllers

    DEFF Research Database (Denmark)

    Abildgaard, Ole

    1990-01-01

    A unified method for solving control system optimization problems is suggested. All system matrices are allowed to be functions of the design variables. The method makes use of an implementation of a sequential quadratic programming algorithm (NLPQL) for solution of general constrained nonlinear...... programming problems. It is shown how to compute the gradients of the objective function and the constraint functions imposing eigenvalue constraints. In an example it is demonstrated how the method can solve a high-dimensional problem, where the initial condition covariance assumption is used to ensure...

  14. Board news

    NARCIS (Netherlands)

    NN,

    1997-01-01

    Composition of the Board of the Foundation Flora Malesiana. — The Board met during the Flora of Thailand Symposium in Phuket. The members Dr. P. Baas and Dr. K. Iwatsuki, whose terms had expired, were happy to continue on the Board. Dr. S.H. Sohmer withdrew and Dr. A. Hay agreed to take the vacant

  15. Board news

    NARCIS (Netherlands)

    NN,

    1997-01-01

    Composition of the Board of the Foundation Flora Malesiana. — The Board met during the Flora of Thailand Symposium in Phuket. The members Dr. P. Baas and Dr. K. Iwatsuki, whose terms had expired, were happy to continue on the Board. Dr. S.H. Sohmer withdrew and Dr. A. Hay agreed to take the vacant c

  16. Optimal sensor placement using FRFs-based clustering method

    Science.gov (United States)

    Li, Shiqi; Zhang, Heng; Liu, Shiping; Zhang, Zhe

    2016-12-01

    The purpose of this work is to develop an optimal sensor placement method by selecting the most relevant degrees of freedom as actual measure position. Based on observation matrix of a structure's frequency response, two optimal criteria are used to avoid the information redundancy of the candidate degrees of freedom. By using principal component analysis, the frequency response matrix can be decomposed into principal directions and their corresponding singular. A relatively small number of principal directions will maintain a system's dominant response information. According to the dynamic similarity of each degree of freedom, the k-means clustering algorithm is designed to classify the degrees of freedom, and effective independence method deletes the sensors which are redundant of each cluster. Finally, two numerical examples and a modal test are included to demonstrate the efficient of the derived method. It is shown that the proposed method provides a way to extract sub-optimal sets and the selected sensors are well distributed on the whole structure.

  17. A new method for nonlinear optimization - experimental results

    Energy Technology Data Exchange (ETDEWEB)

    Loskovska, S.; Percinkova, B.

    1994-12-31

    In this paper an application of a new method for nonlinear optimization problems suggested and presented by B. Percinkova is performed. The method is originally developed and applicated on nonlinear systems. Basis of the method is following: A system of n-nonlinear equations gives as F{sub i}(x{sub 1}, x{sub 2}, x{sub 3}, ..., x{sub n}) = 0; 1 = 1, 2, ..., n and solution domain x{sub pi} {<=} x{sub i} {<=} x{sub ki} i = 1, 2, ..., n is modified by introducing a new variable z. The new system is given by: F{sub i}(x{sub 1}, x{sub 2}, x{sub 3}, ..., x{sub n}) = z; i = 1, 2, ..., n. The system defines a curve in (n + 1) dimensional space. System`s point X = (x{sub i}, x{sub 2}, x{sub 3}, ..., x{sub n}, z) that, the solution of the system is obtained using an interative procedure moving along the curve until the point with z = 0 is reached. In order to applicate method on optimization problems, a basic optimization model given with (min, max)F{sub i}(x{sub 1}, x{sub 2}, x{sub 3}, ..., x{sub n}) with the following optimization space: F{sub i}(x{sub 1}, x{sub 2}, x{sub 3}, ..., x{sub n}) ({<=}{>=})0 : i = 1, 2, ..., n is transformed into a system equivalent to system (2) by (dF/dx{sub i}) = z; i - 1, 2, ..., n. The main purpose of this work is to make relevant evaluation of the method by standard test problems.

  18. Design of large Francis turbine using optimal methods

    Science.gov (United States)

    Flores, E.; Bornard, L.; Tomas, L.; Liu, J.; Couston, M.

    2012-11-01

    Among a high number of Francis turbine references all over the world, covering the whole market range of heads, Alstom has especially been involved in the development and equipment of the largest power plants in the world : Three Gorges (China -32×767 MW - 61 to 113 m), Itaipu (Brazil- 20x750 MW - 98.7m to 127m) and Xiangjiaba (China - 8x812 MW - 82.5m to 113.6m - in erection). Many new projects are under study to equip new power plants with Francis turbines in order to answer an increasing demand of renewable energy. In this context, Alstom Hydro is carrying out many developments to answer those needs, especially for jumbo units such the planned 1GW type units in China. The turbine design for such units requires specific care by using the state of the art in computation methods and the latest technologies in model testing as well as the maximum feedback from operation of Jumbo plants already in operation. We present in this paper how a large Francis turbine can be designed using specific design methods, including the global and local optimization methods. The design of the spiral case, the tandem cascade profiles, the runner and the draft tube are designed with optimization loops involving a blade design tool, an automatic meshing software and a Navier-Stokes solver, piloted by a genetic algorithm. These automated optimization methods, presented in different papers over the last decade, are nowadays widely used, thanks to the growing computation capacity of the HPC clusters: the intensive use of such optimization methods at the turbine design stage allows to reach very high level of performances, while the hydraulic flow characteristics are carefully studied over the whole water passage to avoid any unexpected hydraulic phenomena.

  19. METAHEURISTIC OPTIMIZATION METHODS FOR PARAMETERS ESTIMATION OF DYNAMIC SYSTEMS

    Directory of Open Access Journals (Sweden)

    V. Panteleev Andrei

    2017-01-01

    Full Text Available The article considers the usage of metaheuristic methods of constrained global optimization: “Big Bang - Big Crunch”, “Fireworks Algorithm”, “Grenade Explosion Method” in parameters of dynamic systems estimation, described with algebraic-differential equations. Parameters estimation is based upon the observation results from mathematical model behavior. Their values are derived after criterion minimization, which describes the total squared error of state vector coordinates from the deduced ones with precise values observation at different periods of time. Paral- lelepiped type restriction is imposed on the parameters values. Used for solving problems, metaheuristic methods of constrained global extremum don’t guarantee the result, but allow to get a solution of a rather good quality in accepta- ble amount of time. The algorithm of using metaheuristic methods is given. Alongside with the obvious methods for solving algebraic-differential equation systems, it is convenient to use implicit methods for solving ordinary differen- tial equation systems. Two ways of solving the problem of parameters evaluation are given, those parameters differ in their mathematical model. In the first example, a linear mathematical model describes the chemical action parameters change, and in the second one, a nonlinear mathematical model describes predator-prey dynamics, which characterize the changes in both kinds’ population. For each of the observed examples there are calculation results from all the three methods of optimization, there are also some recommendations for how to choose methods parameters. The obtained numerical results have demonstrated the efficiency of the proposed approach. The deduced parameters ap- proximate points slightly differ from the best known solutions, which were deduced differently. To refine the results one should apply hybrid schemes that combine classical methods of optimization of zero, first and second orders and

  20. Selection of an optimal treatment method for acute periodontitis disease.

    Science.gov (United States)

    Aliev, Rafik A; Aliyev, B F; Gardashova, Latafat A; Huseynov, Oleg H

    2012-04-01

    The present paper is devoted to selection of an optimal treatment method for acute periodontitis by using fuzzy Choquet integral-based approach. We consider application of different treatment methods depending on development stages and symptoms of the disease. The effectiveness of application of different treatment methods in each stage of the disease is linguistically evaluated by a dentist. The stages of the disease are also linguistically described by a dentist. Dentist's linguistic evaluations are represented by fuzzy sets. The total effectiveness of the each considered treatment method is calculated by using fuzzy Choquet integral with fuzzy number-valued integrand and fuzzy number-valued fuzzy measure. The most effective treatment method is determined by using fuzzy ranking method.

  1. Optimal Rapid Restart of Heuristic Methods of NP Hard Problems

    Institute of Scientific and Technical Information of China (English)

    侯越先; 王芳

    2004-01-01

    Many heuristic search methods exhibit a remarkable variability in the time required to solve some particular problem instances. Their cost distributions are often heavy-tailed. It has been demonstrated that, in most cases, rapid restart (RR) method can prominently suppress the heavy-tailed nature of the instances and improve computation efficiency. However, it is usually time-consuming to check whether an algorithm on a specific instance is heavy-tailed or not. Moreover, if the heavy-tailed distribution is confirmed and the RR method is relevant, an optimal RR threshold should be chosen to facilitate the RR mechanism. In this paper, an approximate approach is proposed to quickly check whether an algorithm on a specific instance is heavy-tailed or not.The method is realized by means of calculating the maximal Lyapunov exponent of its generic running trace.Then a statistical formula to estimate the optimal RR threshold is educed. The method is based on common nonparametric estimation, e. g. , Kernel estimation. Two heuristic methods are selected to verify our method. The experimental results are consistent with the theoretical consideration perfectly.

  2. A Localization Method for Multistatic SAR Based on Convex Optimization.

    Directory of Open Access Journals (Sweden)

    Xuqi Zhong

    Full Text Available In traditional localization methods for Synthetic Aperture Radar (SAR, the bistatic range sum (BRS estimation and Doppler centroid estimation (DCE are needed for the calculation of target localization. However, the DCE error greatly influences the localization accuracy. In this paper, a localization method for multistatic SAR based on convex optimization without DCE is investigated and the influence of BRS estimation error on localization accuracy is analysed. Firstly, by using the information of each transmitter and receiver (T/R pair and the target in SAR image, the model functions of T/R pairs are constructed. Each model function's maximum is on the circumference of the ellipse which is the iso-range for its model function's T/R pair. Secondly, the target function whose maximum is located at the position of the target is obtained by adding all model functions. Thirdly, the target function is optimized based on gradient descent method to obtain the position of the target. During the iteration process, principal component analysis is implemented to guarantee the accuracy of the method and improve the computational efficiency. The proposed method only utilizes BRSs of a target in several focused images from multistatic SAR. Therefore, compared with traditional localization methods for SAR, the proposed method greatly improves the localization accuracy. The effectivity of the localization approach is validated by simulation experiment.

  3. A Localization Method for Multistatic SAR Based on Convex Optimization.

    Science.gov (United States)

    Zhong, Xuqi; Wu, Junjie; Yang, Jianyu; Sun, Zhichao; Huang, Yuling; Li, Zhongyu

    2015-01-01

    In traditional localization methods for Synthetic Aperture Radar (SAR), the bistatic range sum (BRS) estimation and Doppler centroid estimation (DCE) are needed for the calculation of target localization. However, the DCE error greatly influences the localization accuracy. In this paper, a localization method for multistatic SAR based on convex optimization without DCE is investigated and the influence of BRS estimation error on localization accuracy is analysed. Firstly, by using the information of each transmitter and receiver (T/R) pair and the target in SAR image, the model functions of T/R pairs are constructed. Each model function's maximum is on the circumference of the ellipse which is the iso-range for its model function's T/R pair. Secondly, the target function whose maximum is located at the position of the target is obtained by adding all model functions. Thirdly, the target function is optimized based on gradient descent method to obtain the position of the target. During the iteration process, principal component analysis is implemented to guarantee the accuracy of the method and improve the computational efficiency. The proposed method only utilizes BRSs of a target in several focused images from multistatic SAR. Therefore, compared with traditional localization methods for SAR, the proposed method greatly improves the localization accuracy. The effectivity of the localization approach is validated by simulation experiment.

  4. Geophysical Inversion With Multi-Objective Global Optimization Methods

    Science.gov (United States)

    Lelièvre, Peter; Bijani, Rodrigo; Farquharson, Colin

    2016-04-01

    We are investigating the use of Pareto multi-objective global optimization (PMOGO) methods to solve numerically complicated geophysical inverse problems. PMOGO methods can be applied to highly nonlinear inverse problems, to those where derivatives are discontinuous or simply not obtainable, and to those were multiple minima exist in the problem space. PMOGO methods generate a suite of solutions that minimize multiple objectives (e.g. data misfits and regularization terms) in a Pareto-optimal sense. This allows a more complete assessment of the possibilities and provides opportunities to calculate statistics regarding the likelihood of particular model features. We are applying PMOGO methods to four classes of inverse problems. The first are discrete-body problems where the inversion determines values of several parameters that define the location, orientation, size and physical properties of an anomalous body represented by a simple shape, for example a sphere, ellipsoid, cylinder or cuboid. A PMOGO approach can determine not only the optimal shape parameters for the anomalous body but also the optimal shape itself. Furthermore, when one expects several anomalous bodies in the subsurface, a PMOGO inversion approach can determine an optimal number of parameterized bodies. The second class of inverse problems are standard mesh-based problems where the physical property values in each cell are treated as continuous variables. The third class of problems are lithological inversions, which are also mesh-based but cells can only take discrete physical property values corresponding to known or assumed rock units. In the fourth class, surface geometry inversions, we consider a fundamentally different type of problem in which a model comprises wireframe surfaces representing contacts between rock units. The physical properties of each rock unit remain fixed while the inversion controls the position of the contact surfaces via control nodes. Surface geometry inversion can be

  5. Metastable legged locomotion: methods to quantify and optimize reliability

    Science.gov (United States)

    Saglam, Cenk O.; Byl, Katie

    2015-05-01

    Measuring the stability of highly-dynamic bipedal locomotion is a challenging but essential task for more capable human-like walking. By discretizing the walking dynamics, we treat the system as a Markov chain, which lends itself to an easy quantification of failure rates by the expected number of steps before falling. This meaningful and intuitive metric is then used for optimizing and benchmarking given controllers. While this method is applicable to any controller scheme, we illustrate the results with two case demonstrations. One scheme is the now-familiar hybrid zero dynamics approach and the other is a method using piece-wise reference trajectories with a sliding mode control. We optimize low-level controllers, to minimize failure rates for any one gait, and we adopt a hierarchical control structure to switch among low-level gaits, providing even more dramatic improvements on the system performance.

  6. Time-dependent optimal heater control using finite difference method

    Energy Technology Data Exchange (ETDEWEB)

    Li, Zhen Zhe; Heo, Kwang Su; Choi, Jun Hoo; Seol, Seoung Yun [Chonnam National Univ., Gwangju (Korea, Republic of)

    2008-07-01

    Thermoforming is one of the most versatile and economical process to produce polymer products. The drawback of thermoforming is difficult to control thickness of final products. Temperature distribution affects the thickness distribution of final products, but temperature difference between surface and center of sheet is difficult to decrease because of low thermal conductivity of ABS material. In order to decrease temperature difference between surface and center, heating profile must be expressed as exponential function form. In this study, Finite Difference Method was used to find out the coefficients of optimal heating profiles. Through investigation, the optimal results using Finite Difference Method show that temperature difference between surface and center of sheet can be remarkably minimized with satisfying temperature of forming window.

  7. Optimal and adaptive methods of processing hydroacoustic signals (review)

    Science.gov (United States)

    Malyshkin, G. S.; Sidel'nikov, G. B.

    2014-09-01

    Different methods of optimal and adaptive processing of hydroacoustic signals for multipath propagation and scattering are considered. Advantages and drawbacks of the classical adaptive (Capon, MUSIC, and Johnson) algorithms and "fast" projection algorithms are analyzed for the case of multipath propagation and scattering of strong signals. The classical optimal approaches to detecting multipath signals are presented. A mechanism of controlled normalization of strong signals is proposed to automatically detect weak signals. The results of simulating the operation of different detection algorithms for a linear equidistant array under multipath propagation and scattering are presented. An automatic detector is analyzed, which is based on classical or fast projection algorithms, which estimates the background proceeding from median filtering or the method of bilateral spatial contrast.

  8. Novel electromagnetism-like mechanism method for multiobjective optimization problems

    Institute of Scientific and Technical Information of China (English)

    Lixia Han,Shujuan Jiang,; Shaojiang Lan

    2015-01-01

    As a new-style stochastic algorithm, the electro-magnetism-like mechanism (EM) method gains more and more attention from many researchers in recent years. A novel model based on EM (NMEM) for multiobjective optimization problems is proposed, which regards the charge of al particles as the con-straints in the current population and the measure of the uniformity of non-dominated solutions as the objective function. The charge of the particle is evaluated based on the dominated concept, and its magnitude determines the direction of a force between two particles. Numerical studies are carried out on six complex test functions and the experimental results demonstrate that the pro-posed NMEM algorithm is a very robust method for solving the multiobjective optimization problems.

  9. Circulating fluidized bed coal-saving optimization control method

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Tengfei; Li, Dewei; Xi, Yugeng; Zhou, Wu [Shanghai Jiao Tong Univ., Shanghai (China). Dept. of Automation; Ministry of Education, Shanghai (China). Key Lab. of System Control and Information Processing; Yin, Debin [Shanghai Xinhua Control Technology (Group) Co., Ltd., Shanghai (China)

    2013-07-01

    The circulating fluidized bed boiler is widely used in thermal power plants. With the proposal of energy-saving emission reduction, how to reduce coal consumption while ensure the output steam quality at the same time has become an important topic. This paper combines the technology of RTO (real-time optimization) and zone control in DMC (dynamic matrix control) to achieve this goal. The proposed method adds the coal consumption into the objective function of DMC controller and the operation point of the boiler is permitted to change within a zone which can be set according to the actual requirements of the circulating fluidized bed boiler. The zone control in DMC provides the freedom to reduce the coal consumption and achieves the economic optimal target. Compared to the simple use of constrained DMC control, the proposed method is verified to be remarkable coal-saving by the case study of a 150 t/h boiler of a power plant in Sichuan.

  10. Optimized Adaptor Polymerase Chain Reaction Method for Efficient Genomic Walking

    Institute of Scientific and Technical Information of China (English)

    Peng XU; Rui-Ying HU; Xiao-Yan DING

    2006-01-01

    Genomic walking is one of the most useful approaches in genome-related research. Three kinds of PCR-based methods are available for this purpose. However, none of them has been generally applied because they are either insensitive or inefficient. Here we present an efficient PCR protocol, an optimized adaptor PCR method for genomic walking. Using a combination of a touchdown PCR program and a special adaptor, the optimized adaptor PCR protocol achieves high sensitivity with low background noise. By applying this protocol, the insertion sites of a gene trap mouse line and two gene promoters from the incompletely sequenced Xenopus laevis genome were successfully identified with high efficiency. The general application of this protocol in genomic walking was promising.

  11. Optimal design method for fast carry-skip adders

    Science.gov (United States)

    Lee, Songjun; Swartzlander, Earl E., Jr.

    2001-11-01

    A carry-skip adder is faster than a ripple carry adder and it has a simple structure. To maximize the speed it is necessary to optimize the width of the blocks that comprise the carry skip adder. This paper presents a simple algorithm to select the size of each block. Assuming that each logic gate has a unit delay, the algorithm achieves slightly faster designs for 64 and 128 bit adders than previous methods developed by Guyot, et al. and Kantabutra.

  12. Experimental methods for the analysis of optimization algorithms

    CERN Document Server

    Bartz-Beielstein, Thomas; Paquete, Luis; Preuss, Mike

    2010-01-01

    In operations research and computer science it is common practice to evaluate the performance of optimization algorithms on the basis of computational results, and the experimental approach should follow accepted principles that guarantee the reliability and reproducibility of results. However, computational experiments differ from those in other sciences, and the last decade has seen considerable methodological research devoted to understanding the particular features of such experiments and assessing the related statistical methods. This book consists of methodological contributions on diffe

  13. Method for optimization of statically determined articulated structures

    OpenAIRE

    Parras Galán, L.; Montes Tubío, M.; García Guzmán, A.; Entrenas Angulo, J.A.; de Dios Palomares, R.

    1985-01-01

    An algorithm of mathematical programmation for the optimum disign of iso-static articulate structures has been developed. The characteristics of the proposed algorithm are: a) It not requires that the objective function or the restriction equations be derivable. b) They use unidimensional methods of unidimensional optimization to pass over from a given solution to a better one. c) To introduce contingent procedures to obtain Information which leads to a better solution. Those characteristics ...

  14. Gradient Gene Algorithm: a Fast Optimization Method to MST Problem

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The extension of Minimum Spanning Tree(MST) problem is an NP hardproblem which does not exit a polynomial time algorithm. In this paper, a fast optimizat ion method on MST problem--the Gradient Gene Algorithm is introduced. Compar ed with other evolutionary algorithms on MST problem, it is more advanced: firstly, very simple and easy to realize; then, efficient and accurate; finally general on other combination optimization problems.

  15. Time-of-Travel Methods for Measuring Optical Flow on Board a Micro Flying Robot

    Directory of Open Access Journals (Sweden)

    Erik Vanhoutte

    2017-03-01

    Full Text Available For use in autonomous micro air vehicles, visual sensors must not only be small, lightweight and insensitive to light variations; on-board autopilots also require fast and accurate optical flow measurements over a wide range of speeds. Using an auto-adaptive bio-inspired Michaelis–Menten Auto-adaptive Pixel (M 2 APix analog silicon retina, in this article, we present comparative tests of two optical flow calculation algorithms operating under lighting conditions from 6 × 10 − 7 to 1 . 6 × 10 − 2 W·cm − 2 (i.e., from 0.2 to 12,000 lux for human vision. Contrast “time of travel” between two adjacent light-sensitive pixels was determined by thresholding and by cross-correlating the two pixels’ signals, with measurement frequency up to 5 kHz for the 10 local motion sensors of the M 2 APix sensor. While both algorithms adequately measured optical flow between 25 ∘ /s and 1000 ∘ /s, thresholding gave rise to a lower precision, especially due to a larger number of outliers at higher speeds. Compared to thresholding, cross-correlation also allowed for a higher rate of optical flow output (99 Hz and 1195 Hz, respectively but required substantially more computational resources.

  16. An Optimized Method for Terrain Reconstruction Based on Descent Images

    Directory of Open Access Journals (Sweden)

    Xu Xinchao

    2016-02-01

    Full Text Available An optimization method is proposed to perform high-accuracy terrain reconstruction of the landing area of Chang’e III. First, feature matching is conducted using geometric model constraints. Then, the initial terrain is obtained and the initial normal vector of each point is solved on the basis of the initial terrain. By changing the vector around the initial normal vector in small steps a set of new vectors is obtained. By combining these vectors with the direction of light and camera, the functions are set up on the basis of a surface reflection model. Then, a series of gray values is derived by solving the equations. The new optimized vector is recorded when the obtained gray value is closest to the corresponding pixel. Finally, the optimized terrain is obtained after iteration of the vector field. Experiments were conducted using the laboratory images and descent images of Chang’e III. The results showed that the performance of the proposed method was better than that of the classical feature matching method. It can provide a reference for terrain reconstruction of the landing area in subsequent moon exploration missions.

  17. Split Bregman's optimization method for image construction in compressive sensing

    Science.gov (United States)

    Skinner, D.; Foo, S.; Meyer-Bäse, A.

    2014-05-01

    The theory of compressive sampling (CS) was reintroduced by Candes, Romberg and Tao, and D. Donoho in 2006. Using a priori knowledge that a signal is sparse, it has been mathematically proven that CS can defY Nyquist sampling theorem. Theoretically, reconstruction of a CS image relies on the minimization and optimization techniques to solve this complex almost NP-complete problem. There are many paths to consider when compressing and reconstructing an image but these methods have remained untested and unclear on natural images, such as underwater sonar images. The goal of this research is to perfectly reconstruct the original sonar image from a sparse signal while maintaining pertinent information, such as mine-like object, in Side-scan sonar (SSS) images. Goldstein and Osher have shown how to use an iterative method to reconstruct the original image through a method called Split Bregman's iteration. This method "decouples" the energies using portions of the energy from both the !1 and !2 norm. Once the energies are split, Bregman iteration is used to solve the unconstrained optimization problem by recursively solving the problems simultaneously. The faster these two steps or energies can be solved then the faster the overall method becomes. While the majority of CS research is still focused on the medical field, this paper will demonstrate the effectiveness of the Split Bregman's methods on sonar images.

  18. A conjugate gradient method with descent direction for unconstrained optimization

    Science.gov (United States)

    Yuan, Gonglin; Lu, Xiwen; Wei, Zengxin

    2009-11-01

    A modified conjugate gradient method is presented for solving unconstrained optimization problems, which possesses the following properties: (i) The sufficient descent property is satisfied without any line search; (ii) The search direction will be in a trust region automatically; (iii) The Zoutendijk condition holds for the Wolfe-Powell line search technique; (iv) This method inherits an important property of the well-known Polak-Ribière-Polyak (PRP) method: the tendency to turn towards the steepest descent direction if a small step is generated away from the solution, preventing a sequence of tiny steps from happening. The global convergence and the linearly convergent rate of the given method are established. Numerical results show that this method is interesting.

  19. New design method for valves internals, to optimize process

    Energy Technology Data Exchange (ETDEWEB)

    Jorge, Leonardo [PDVSA (Venezuela)

    2011-07-01

    In the heavy oil industry, various methods can be used to reduce the viscosity of oil, one of them being the injection of diluent. This method is commonly used in the Orinoco oil belt but it requires good control of the volume of diluent injected as well as the gas flow to optimize production; thus flow control valves need to be accurate. A new valve with a new method was designed with the characteristic of being very reliable and was then bench tested and compared with the other commercially available valves. Results showed better repeatability, accuracy and reliability with lower maintenance for the new method. The use of this valve provides significant savings while distributing the exact amount of fluids; up to date a less than 2% failure rate has been recorded in the field. The new method developed demonstrated impressive performance and PDVSA has decided to use it in mass.

  20. Optimization design of thumbspica splint using finite element method.

    Science.gov (United States)

    Huang, Tz-How; Feng, Chi-Kung; Gung, Yih-Wen; Tsai, Mei-Wun; Chen, Chen-Sheng; Liu, Chien-Lin

    2006-12-01

    De Quervain's tenosynovitis is often observed on repetitive flexion of the thumb. In the clinical setting, the conservative treatment is usually an applied thumbspica splint to immobilize the thumb. However, the traditional thumbspica splint is bulky and heavy. Thus, this study used the finite element (FE) method to remove redundant material in order to reduce the splint's weight and increase ventilation. An FE model of a thumbspica splint was constructed using ANSYS9.0 software. A maximum lateral thumb pinch force of 98 N was used as the input loading condition for the FE model. This study implemented topology optimization and design optimization to seek the optimal thickness and shape of the splint. This new design was manufactured and compared with the traditional thumbspica splint. Ten thumbspica splints were tested in a materials testing system, and statistically analyzed using an independent t test. The optimal thickness of the thumbspica splint was 3.2 mm. The new design is not significantly different from the traditional splint in the immobilization effect. However, the volume of this new design has been reduced by about 35%. This study produced a new thumbspica splint shape with less volume, but had a similar immobilization effect compared to the traditional shape. In a clinical setting, this result can be used by the occupational therapist as a reference for manufacturing lighter thumbspica splints for patients with de Quervain's tenosynovitis.

  1. Robust Optimal Adaptive Control Method with Large Adaptive Gain

    Science.gov (United States)

    Nguyen, Nhan T.

    2009-01-01

    In the presence of large uncertainties, a control system needs to be able to adapt rapidly to regain performance. Fast adaptation is referred to the implementation of adaptive control with a large adaptive gain to reduce the tracking error rapidly. However, a large adaptive gain can lead to high-frequency oscillations which can adversely affect robustness of an adaptive control law. A new adaptive control modification is presented that can achieve robust adaptation with a large adaptive gain without incurring high-frequency oscillations as with the standard model-reference adaptive control. The modification is based on the minimization of the Y2 norm of the tracking error, which is formulated as an optimal control problem. The optimality condition is used to derive the modification using the gradient method. The optimal control modification results in a stable adaptation and allows a large adaptive gain to be used for better tracking while providing sufficient stability robustness. Simulations were conducted for a damaged generic transport aircraft with both standard adaptive control and the adaptive optimal control modification technique. The results demonstrate the effectiveness of the proposed modification in tracking a reference model while maintaining a sufficient time delay margin.

  2. Continuous Control Artificial Potential Function Methods and Optimal Control

    Science.gov (United States)

    2014-03-27

    Method, namely r̈VDSVAPF = −K̇SKR∇φ−KSK̇R∇φ−KSKRH(φ)ṙ −KD (KSKR∇φ+ ṙ) . The above dynamics are very nonlinear due to the trigonometric functions (inside...constraints (on KS and θ) and the deletion of trigonometric functions . The suspected reasons for the larger computa- tional expense are twofold. First, this...Continuous Control Artificial Potential Function Methods and Optimal Control THESIS R. Andrew Fields, Civ, USAF AFIT-ENY-14-M-20 DEPARTMENT OF THE

  3. Optimization in engineering sciences approximate and metaheuristic methods

    CERN Document Server

    Stefanoiu, Dan; Popescu, Dumitru; Filip, Florin Gheorghe; El Kamel, Abdelkader

    2014-01-01

    The purpose of this book is to present the main metaheuristics and approximate and stochastic methods for optimization of complex systems in Engineering Sciences. It has been written within the framework of the European Union project ERRIC (Empowering Romanian Research on Intelligent Information Technologies), which is funded by the EU's FP7 Research Potential program and has been developed in co-operation between French and Romanian teaching researchers. Through the principles of various proposed algorithms (with additional references) this book allows the reader to explore various methods o

  4. The Value of Methodical Management: Optimizing Science Results

    Science.gov (United States)

    Saby, Linnea

    2016-01-01

    As science progresses, making new discoveries in radio astronomy becomes increasingly complex. Instrumentation must be incredibly fine-tuned and well-understood, scientists must consider the skills and schedules of large research teams, and inter-organizational projects sometimes require coordination between observatories around the globe. Structured and methodical management allows scientists to work more effectively in this environment and leads to optimal science output. This report outlines the principles of methodical project management in general, and describes how those principles are applied at the National Radio Astronomy Observatory (NRAO) in Charlottesville, Virginia.

  5. Recovery of metals from waste printed circuit boards by a mechanical method using a water medium.

    Science.gov (United States)

    Duan, Chenlong; Wen, Xuefeng; Shi, Changsheng; Zhao, Yuemin; Wen, Baofeng; He, Yaqun

    2009-07-15

    Research on the recycling of waste printed circuit boards (PCB) is at the forefront of environmental pollution prevention and resource recycling. To effectively crush waste PCB and to solve the problem of secondary pollution from fugitive odors and dust created during the crushing process, a wet impacting crusher was employed to achieve comminution liberation of the PCB in a water medium. The function of water in the crushing process was analyzed. When using slippery hammerheads, a rotation speed of 1470 rpm, a water flow of 6m(3)/h and a sieve plate aperture of 2.2mm, 95.87% of the crushed product was sized less than 1mm. 94.30% of the metal was in this grade of product. Using smashed material graded -1mm for further research, a Falcon concentrator was used to recover the metal from the waste PCB. Engineering considerations were the liberation degree, the distribution ratio of the metal and a way to simplify the technology. The separation mechanism for fine particles of different densities in a Falcon concentrator was analyzed in detail and the separation process in the segregation and separation zones was deduced. Also, the magnitude of centrifugal acceleration, the back flow water pressure and the feed slurry concentration, any of which might affect separation results, were studied. A recovery model was established using Design-Expert software. Separating waste PCB, crushed to -1mm, with the Falcon separator gave a concentrated product graded 92.36% metal with a recovery of 97.05%. To do this the reverse water pressure was 0.05 MPa, the speed transducer frequency was set at 30 Hz and the feed density was 20 g/l. A flow diagram illustrating the new technique of wet impact crushing followed by separation with a Falcon concentrator is provided. The technique will prevent environmental pollution from waste PCB and allow the effective recovery of resources. Water was used as the medium throughout the whole process.

  6. Design optimization methods for genomic DNA tiling arrays.

    Science.gov (United States)

    Bertone, Paul; Trifonov, Valery; Rozowsky, Joel S; Schubert, Falk; Emanuelsson, Olof; Karro, John; Kao, Ming-Yang; Snyder, Michael; Gerstein, Mark

    2006-02-01

    A recent development in microarray research entails the unbiased coverage, or tiling, of genomic DNA for the large-scale identification of transcribed sequences and regulatory elements. A central issue in designing tiling arrays is that of arriving at a single-copy tile path, as significant sequence cross-hybridization can result from the presence of non-unique probes on the array. Due to the fragmentation of genomic DNA caused by the widespread distribution of repetitive elements, the problem of obtaining adequate sequence coverage increases with the sizes of subsequence tiles that are to be included in the design. This becomes increasingly problematic when considering complex eukaryotic genomes that contain many thousands of interspersed repeats. The general problem of sequence tiling can be framed as finding an optimal partitioning of non-repetitive subsequences over a prescribed range of tile sizes, on a DNA sequence comprising repetitive and non-repetitive regions. Exact solutions to the tiling problem become computationally infeasible when applied to large genomes, but successive optimizations are developed that allow their practical implementation. These include an efficient method for determining the degree of similarity of many oligonucleotide sequences over large genomes, and two algorithms for finding an optimal tile path composed of longer sequence tiles. The first algorithm, a dynamic programming approach, finds an optimal tiling in linear time and space; the second applies a heuristic search to reduce the space complexity to a constant requirement. A Web resource has also been developed, accessible at http://tiling.gersteinlab.org, to generate optimal tile paths from user-provided DNA sequences.

  7. Optimized optical clearing method for imaging central nervous system

    Science.gov (United States)

    Yu, Tingting; Qi, Yisong; Gong, Hui; Luo, Qingming; Zhu, Dan

    2015-03-01

    The development of various optical clearing methods provides a great potential for imaging entire central nervous system by combining with multiple-labelling and microscopic imaging techniques. These methods had made certain clearing contributions with respective weaknesses, including tissue deformation, fluorescence quenching, execution complexity and antibody penetration limitation that makes immunostaining of tissue blocks difficult. The passive clarity technique (PACT) bypasses those problems and clears the samples with simple implementation, excellent transparency with fine fluorescence retention, but the passive tissue clearing method needs too long time. In this study, we not only accelerate the clearing speed of brain blocks but also preserve GFP fluorescence well by screening an optimal clearing temperature. The selection of proper temperature will make PACT more applicable, which evidently broaden the application range of this method.

  8. Multimineral optimization processing method based on elemental capture spectroscopy logging

    Institute of Scientific and Technical Information of China (English)

    Feng Zhou; Li Xin-Tong; Wu Hong-Liang; Xia Shou-Ji; Liu Ying-Ming

    2014-01-01

    Calculating the mineral composition is a critical task in log interpretation. Elemental capture spectroscopy (ECS) log provides the weight percentages of twelve common elements, which lays the foundation for the accurate calculation of mineral compositions. Previous processing methods calculated the formation composition via the conversion relation between the formation chemistry and minerals. Thus, their applicability is limited and the method precision is relatively low. In this study, we present a multimineral optimization processing method based on the ECS log. We derived the ECS response equations for calculating the formation composition, then, determined the logging response values for the elements of common minerals using core data and theoretical calculations. Finally, a software module was developed. The results of the new method are consistent with core data and the mean absolute error is less than 10%.

  9. Optimization and modification of the method for detection of rhamnolipids

    Directory of Open Access Journals (Sweden)

    Takeshi Tabuchi

    2015-10-01

    Full Text Available Use of biosurfactants in bioremediation, facilitates and accelerates microbial degradation of hydrocarbons. CTAB/MB agar method created by Siegmund & Wagner for screening of rhamnolipids (RL producing strains, has been widely used but has not improved significantly for more than 20 years. To optimize the technique as a quantitative method, CTAB/MB agar plates were made and different variables were tested, like incubation time, cooling, CTAB concentration, methylene blue presence, wells diameter and inocula volume. Furthermore, a new method for RL detection within halos was developed: precipitation of RL with HCl, allows the formation a new halos pattern, easier to observe and to measure. This research reaffirm that this method is not totally suitable for a fine quantitative analysis, because of the difficulty to accurately correlate RL concentration and the area of the halos. RL diffusion does not seem to have a simple behavior and there are a lot of factors that affect RL migration rate.

  10. An Optimized Constraint Decomposition Method in Concurrent Engineering

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    In order to facilitate solution, a complex problem is normally decomposed into many small sub-problems during product development process. Teams are formed to resolve each sub-problem. The original problem is resolved from solutions of sub-problems. Ideally, sub-problems are not only mutually independent but also inherent parameters of original problem. Solution of original problem can be directly derived from the collection of solutions from simplified sub-problems. In practice, the degree of interdependency is indeed reduced, sub-problems are neither totally independent nor all inherent parameters of original problem. This paper discusses team coordination under this condition and design solution from each team, which not only satisfies total requirements but also is an optimal one. The suggested optimized constraint decomposition method will insure workable Pareto solution.

  11. Stochastic Recursive Algorithms for Optimization Simultaneous Perturbation Methods

    CERN Document Server

    Bhatnagar, S; Prashanth, L A

    2013-01-01

    Stochastic Recursive Algorithms for Optimization presents algorithms for constrained and unconstrained optimization and for reinforcement learning. Efficient perturbation approaches form a thread unifying all the algorithms considered. Simultaneous perturbation stochastic approximation and smooth fractional estimators for gradient- and Hessian-based methods are presented. These algorithms: • are easily implemented; • do not require an explicit system model; and • work with real or simulated data. Chapters on their application in service systems, vehicular traffic control and communications networks illustrate this point. The book is self-contained with necessary mathematical results placed in an appendix. The text provides easy-to-use, off-the-shelf algorithms that are given detailed mathematical treatment so the material presented will be of significant interest to practitioners, academic researchers and graduate students alike. The breadth of applications makes the book appropriate for reader from sim...

  12. Active control of transient rotordynamic vibration by optimal control methods

    Science.gov (United States)

    Palazzolo, A. B.; Lin, R. R.; Alexander, R. M.; Kascak, A. F.

    1988-01-01

    Although considerable effort has been put into the study of steady state vibration control, there are few methods applicable to transient vibration control of rotorbearing systems. In this paper optimal control theory has been adopted to minimize rotor vibration due to sudden imbalance, e.g., blade loss. The system gain matrix is obtained by choosing the weighting matrices and solving the Riccati equation. Control forces are applied to the system via a feedback loop. A seven mass rotor system is simulated for illustration. A relationship between the number of sensors and the number of modes used in the optimal control model is investigated. Comparisons of responses are made for various configurations of modes, sensors, and actuators. Furthermore, spillover effect is examined by comparing results from collocated and noncollocated sensor configurations. Results show that shaft vibration is significantly attenuated in the closed loop system.

  13. Quasi-Newton Method for Optimal Blank Allowance Balancing

    Institute of Scientific and Technical Information of China (English)

    CHEN Manyi

    2006-01-01

    A balancing technique for casting or forging parts to be machined is presented in this paper. It allows an optimal part setup to make sure that no shortage of material (undercut) will occur during machining. Particularly in the heavy part industry, where the resulting casting size and shape may deviate from expectations, the balancing process discovers whether or not the design model is totally enclosed in the actual part to be machined. The alignment is an iterative process involving nonlinear constrained optimization, which forces data points to lie outside the nominal model under a specific order of priority. Newton methods for non-linear numerical minimization are rarely applied to this problem because of the high cost of computing. In this paper, Newton methods are applied to the balancing of blank part. The aforesaid algorithm is demonstrated in term of a marine propeller blade, and result shows that The Newton methods are more efficient and accurate than those implemented in past research and have distinct advantages compared to the registration methods widely used today.

  14. Methods for optimizing over the efficient and weakly efficient sets of an affine fractional vector optimization program

    DEFF Research Database (Denmark)

    Le, T.H.A.; Pham, D. T.; Canh, Nam Nguyen;

    2010-01-01

    Both the efficient and weakly efficient sets of an affine fractional vector optimization problem, in general, are neither convex nor given explicitly. Optimization problems over one of these sets are thus nonconvex. We propose two methods for optimizing a real-valued function over the efficient a...

  15. Integrating the TRIZ and Taguchi's Method in the Optimization of Processes Parameters for SMT

    Directory of Open Access Journals (Sweden)

    Yung-Tsan Jou

    2013-01-01

    Full Text Available SMT is an assembly technology for core circuit board parts. Unless process parameters are effectively controlled, poor solderability may result in a decline in product quality. This study looks at an SMT manufacturing process in a multinational company. First, the TRIZ contradiction matrix is revised to investigate the association between the 39 parameters in the contradiction matrix and 13 parameters that influence the unevenness of solder paste in the solder paste printing process. Expert verification is then used to screen the key factors affecting the quality of SMT, which are then combined with Taguchi's method to identify the optimal parameter set influencing the thickness of SMT solder paste. Results. TRIZ identifies squeegee pressure, ejection speed, squeegee speed, and squeegee angle as the four parameters with the greatest influence on SMT solder paste thickness. Taguchi's method is used to identify the optimum levels set for the experimental factors and carry out confirmation experiments. The S/N ratio improved from 21.732 db to 26.632 db, while the mean also improved from the current 0.163 mm to 0.155 mm, close to the target value of 0.15 mm. The results show that applying TRIZ and Taguchi's method for the purpose of product improvement is feasible.

  16. Advanced Topology Optimization Methods for Conceptual Architectural Design

    DEFF Research Database (Denmark)

    Aage, Niels; Amir, Oded; Clausen, Anders

    2015-01-01

    in topological optimization: Interactive control and continuous visualization; embedding flexible voids within the design space; consideration of distinct tension / compression properties; and optimization of dual material systems. In extension, optimization procedures for skeletal structures such as trusses...

  17. Optimizing ETL by a Two-level Data Staging Method

    DEFF Research Database (Denmark)

    Iftikhar, Nadeem

    2016-01-01

    In data warehousing, the data from source systems are populated into a central data warehouse (DW) through extraction, transformation and loading (ETL). The standard ETL approach usually uses sequential jobs to process the data with dependencies, such as dimension and fact data. It is a non......-/late-arriving data, and fast-/slowly-changing data. The introduced additional staging area decouples loading process from data extraction and transformation, which improves ETL flexibility and minimizes intervention to the data warehouse. This paper evaluates the proposed method empirically, which shows......-trivial task to process the so-called early-/late-arriving data, which arrive out of order. This paper proposes a two-level data staging area method to optimize ETL. The proposed method is an all-in-one solution that supports processing different types of data from operational systems, including early...

  18. Structured light system calibration method with optimal fringe angle.

    Science.gov (United States)

    Li, Beiwen; Zhang, Song

    2014-11-20

    For structured light system calibration, one popular approach is to treat the projector as an inverse camera. This is usually performed by projecting horizontal and vertical sequences of patterns to establish one-to-one mapping between camera points and projector points. However, for a well-designed system, either horizontal or vertical fringe images are not sensitive to depth variation and thus yield inaccurate mapping. As a result, the calibration accuracy is jeopardized if a conventional calibration method is used. To address this limitation, this paper proposes a novel calibration method based on optimal fringe angle determination. Experiments demonstrate that our calibration approach can increase the measurement accuracy up to 38% compared to the conventional calibration method with a calibration volume of 300(H)  mm×250(W)  mm×500(D)  mm.

  19. Methods to optimize myxobacterial fermentations using off-gas analysis

    Directory of Open Access Journals (Sweden)

    Hüttel Stephan

    2012-05-01

    Full Text Available Abstract Background The influence of carbon dioxide and oxygen on microbial secondary metabolite producers and the maintenance of these two parameters at optimal levels have been studied extensively. Nevertheless, most studies have focussed on their influence on specific product formation and condition optimization of established processes. Considerably less attention has been paid to the influence of reduced or elevated carbon dioxide and oxygen levels on the overall metabolite profiles of the investigated organisms. The synergistic action of both gases has garnered even less attention. Results We show that the composition of the gas phase is highly important for the production of different metabolites and present a simple approach that enables the maintenance of defined concentrations of both O2 and CO2 during bioprocesses over broad concentration ranges with a minimal instrumental setup by using endogenously produced CO2. The metabolite profiles of a myxobacterium belonging to the genus Chondromyces grown under various concentrations of CO2 and O2 showed considerable differences. Production of two unknown, highly cytotoxic compounds and one antimicrobial substance was found to increase depending on the gas composition. In addition, the observation of CO2 and O2 in the exhaust gas allowed optimization and control of production processes. Conclusions Myxobacteria are becoming increasingly important due to their potential for bioactive secondary metabolite production. Our studies show that the influence of different gas partial pressures should not be underestimated during screening processes for novel compounds and that our described method provides a simple tool to investigate this question.

  20. Performance enhancement of a pump impeller using optimal design method

    Science.gov (United States)

    Jeon, Seok-Yun; Kim, Chul-Kyu; Lee, Sang-Moon; Yoon, Joon-Yong; Jang, Choon-Man

    2017-04-01

    This paper presents the performance evaluation of a regenerative pump to increase its efficiency using optimal design method. Two design parameters which define the shape of the pump impeller, are introduced and analyzed. Pump performance is evaluated by numerical simulation and design of experiments(DOE). To analyze three-dimensional flow field in the pump, general analysis code, CFX, is used in the present work. Shear stress turbulence model is employed to estimate the eddy viscosity. Experimental apparatus with an open-loop facility is set up for measuring the pump performance. Pump performance, efficiency and pressure, obtained from numerical simulation are validated by comparison with the results of experiments. Throughout the shape optimization of the pump impeller at the operating flow condition, the pump efficiency is successfully increased by 3 percent compared to the reference pump. It is noted that the pressure increase of the optimum pump is mainly caused by higher momentum force generated inside blade passage due to the optimal blade shape. Comparisons of pump internal flow on the reference and optimum pump are also investigated and discussed in detail.

  1. Multiobjective Optimization Methods for Congestion Management in Deregulated Power Systems

    Directory of Open Access Journals (Sweden)

    K. Vijayakumar

    2012-01-01

    Full Text Available Congestion management is one of the important functions performed by system operator in deregulated electricity market to ensure secure operation of transmission system. This paper proposes two effective methods for transmission congestion alleviation in deregulated power system. Congestion or overload in transmission networks is alleviated by rescheduling of generators and/or load shedding. The two objectives conflicting in nature (1 transmission line over load and (2 congestion cost are optimized in this paper. The multiobjective fuzzy evolutionary programming (FEP and nondominated sorting genetic algorithm II methods are used to solve this problem. FEP uses the combined advantages of fuzzy and evolutionary programming (EP techniques and gives better unique solution satisfying both objectives, whereas nondominated sorting genetic algorithm (NSGA II gives a set of Pareto-optimal solutions. The methods propose an efficient and reliable algorithm for line overload alleviation due to critical line outages in a deregulated power markets. The quality and usefulness of the algorithm is tested on IEEE 30 bus system.

  2. AN ADAPTIVE TRUST REGION METHOD FOR EQUALITY CONSTRAINED OPTIMIZATION

    Institute of Scientific and Technical Information of China (English)

    ZHANG Juliang; ZHANG Xiangsun; ZHUO Xinjian

    2003-01-01

    In this paper, a trust region method for equality constrained optimization based on nondifferentiable exact penalty is proposed. In this algorithm, the trail step is characterized by computation of its normal component being separated from computation of its tangential component, i.e., only the tangential component of the trail step is constrained by trust radius while the normal component and trail step itself have no constraints. The other main characteristic of the algorithm is the decision of trust region radius. Here, the decision of trust region radius uses the information of the gradient of objective function and reduced Hessian. However, Maratos effect will occur when we use the nondifferentiable exact penalty function as the merit function. In order to obtain the superlinear convergence of the algorithm, we use the twice order correction technique. Because of the speciality of the adaptive trust region method, we use twice order correction when p = 0 (the definition is as in Section 2) and this is different from the traditional trust region methods for equality constrained optimization. So the computation of the algorithm in this paper is reduced. What is more, we can prove that the algorithm is globally and superlinearly convergent.

  3. Optimization of Statistical Methods Impact on Quantitative Proteomics Data.

    Science.gov (United States)

    Pursiheimo, Anna; Vehmas, Anni P; Afzal, Saira; Suomi, Tomi; Chand, Thaman; Strauss, Leena; Poutanen, Matti; Rokka, Anne; Corthals, Garry L; Elo, Laura L

    2015-10-02

    As tools for quantitative label-free mass spectrometry (MS) rapidly develop, a consensus about the best practices is not apparent. In the work described here we compared popular statistical methods for detecting differential protein expression from quantitative MS data using both controlled experiments with known quantitative differences for specific proteins used as standards as well as "real" experiments where differences in protein abundance are not known a priori. Our results suggest that data-driven reproducibility-optimization can consistently produce reliable differential expression rankings for label-free proteome tools and are straightforward in their application.

  4. Experimental Methods for the Analysis of Optimization Algorithms

    DEFF Research Database (Denmark)

    of solution quality, runtime and other measures; and the third part collects advanced methods from experimental design for configuring and tuning algorithms on a specific class of instances with the goal of using the least amount of experimentation. The contributor list includes leading scientists...... in algorithm design, statistical design, optimization and heuristics, and most chapters provide theoretical background and are enriched with case studies. This book is written for researchers and practitioners in operations research and computer science who wish to improve the experimental assessment...

  5. A ROBUST SQP METHOD FOR OPTIMIZATION WITH INEQUALITY CONSTRAINTS

    Institute of Scientific and Technical Information of China (English)

    Juliang Zhang; Xiangsun Zhang

    2003-01-01

    A new algorithm for inequality constrained optimization is presented, which solves a linear programming subproblem and a quadratic subproblem at each iteration. The algorithm can circumvent the difficulties associated with the possible inconsistency of QP subproblem of the original SQP method. Moreover, the algorithm can converge to a point which satisfies a certain first-order necessary condition even if the original problem is itself infeasible. Under certain condition, some global convergence results are proved and local superlinear convergence results are also obtained. Preliminary numerical results are reported.

  6. Adaptive nonmonotone line search method for unconstrained optimization

    Institute of Scientific and Technical Information of China (English)

    Qunyan ZHOU; Wenyu SUN

    2008-01-01

    In this paper, an adaptive nonmonotone line search method for unconstrained minimization problems is proposed. At every iteration, the new algorithm selects only one of the two directions: a Newton-type direc-tion and a negative curvature direction, to perform the line search. The nonmonotone technique is included in the backtracking line search when the Newton-type direction is the search direction. Furthermore, if the negative curvature direction is the search direction, we increase the steplength un-der certain conditions. The global convergence to a stationary point with second-order optimality conditions is established. Some numerical results which show the efficiency of the new algorithm are reported.

  7. An Optimal Method for Developing Global Supply Chain Management System

    Directory of Open Access Journals (Sweden)

    Hao-Chun Lu

    2013-01-01

    Full Text Available Owing to the transparency in supply chains, enhancing competitiveness of industries becomes a vital factor. Therefore, many developing countries look for a possible method to save costs. In this point of view, this study deals with the complicated liberalization policies in the global supply chain management system and proposes a mathematical model via the flow-control constraints, which are utilized to cope with the bonded warehouses for obtaining maximal profits. Numerical experiments illustrate that the proposed model can be effectively solved to obtain the optimal profits in the global supply chain environment.

  8. Comparison of Optimal Design Methods in Inverse Problems

    Science.gov (United States)

    2011-05-11

    corresponding FIM can be estimated by F̂ (τ) = F̂ (τ, θ̂OLS) = (Σ̂ N (θ̂OLS)) −1. (13) The asymptotic standard errors are given by SEk (θ0) = √ (ΣN0 )kk, k...1, . . . , p. (14) These standard errors are estimated in practice (when θ0 and σ0 are not known) by SEk (θ̂OLS) = √ (Σ̂N (θ̂OLS))kk, k = 1... SEk (θ̂boot) = √ Cov(θ̂boot)kk. We will compare the optimal design methods using the standard errors resulting from the op- timal time points each

  9. Optimal Control for Bufferbloat Queue Management Using Indirect Method with Parametric Optimization

    Directory of Open Access Journals (Sweden)

    Amr Radwan

    2016-01-01

    Full Text Available Because memory buffers become larger and cheaper, they have been put into network devices to reduce the number of loss packets and improve network performance. However, the consequences of large buffers are long queues at network bottlenecks and throughput saturation, which has been recently noticed in research community as bufferbloat phenomenon. To address such issues, in this article, we design a forward-backward optimal control queue algorithm based on an indirect approach with parametric optimization. The cost function which we want to minimize represents a trade-off between queue length and packet loss rate performance. Through the integration of an indirect approach with parametric optimization, our proposal has advantages of scalability and accuracy compared to direct approaches, while still maintaining good throughput and shorter queue length than several existing queue management algorithms. All numerical analysis, simulation in ns-2, and experiment results are provided to solidify the efficiency of our proposal. In detailed comparisons to other conventional algorithms, the proposed procedure can run much faster than direct collocation methods while maintaining a desired short queue (≈40 packets in simulation and 80 (ms in experiment test.

  10. Joint Geophysical Inversion With Multi-Objective Global Optimization Methods

    Science.gov (United States)

    Lelievre, P. G.; Bijani, R.; Farquharson, C. G.

    2015-12-01

    Pareto multi-objective global optimization (PMOGO) methods generate a suite of solutions that minimize multiple objectives (e.g. data misfits and regularization terms) in a Pareto-optimal sense. Providing a suite of models, as opposed to a single model that minimizes a weighted sum of objectives, allows a more complete assessment of the possibilities and avoids the often difficult choice of how to weight each objective. We are applying PMOGO methods to three classes of inverse problems. The first class are standard mesh-based problems where the physical property values in each cell are treated as continuous variables. The second class of problems are also mesh-based but cells can only take discrete physical property values corresponding to known or assumed rock units. In the third class we consider a fundamentally different type of inversion in which a model comprises wireframe surfaces representing contacts between rock units; the physical properties of each rock unit remain fixed while the inversion controls the position of the contact surfaces via control nodes. This third class of problem is essentially a geometry inversion, which can be used to recover the unknown geometry of a target body or to investigate the viability of a proposed Earth model. Joint inversion is greatly simplified for the latter two problem classes because no additional mathematical coupling measure is required in the objective function. PMOGO methods can solve numerically complicated problems that could not be solved with standard descent-based local minimization methods. This includes the latter two classes of problems mentioned above. There are significant increases in the computational requirements when PMOGO methods are used but these can be ameliorated using parallelization and problem dimension reduction strategies.

  11. Robust method optimization strategy-a useful tool for method transfer: the case of SFC.

    Science.gov (United States)

    Dispas, Amandine; Lebrun, Pierre; Andri, Bertyl; Rozet, Eric; Hubert, Philippe

    2014-01-01

    The concept of Quality by Design (QbD) is now well established in pharmaceutical industry and should be applied to the development of any analytical methods. In this context, the key concept of Design Space (DS) was introduced in the field of analytical method optimization. In chromatographic words, the DS is the space of chromatographic conditions that will ensure the quality of peaks separation, thus DS is a zone of robustness. In the present study, the interest of robust method optimization strategy was investigated in the context of direct method transfer from sending to receiving laboratory. The benefit of this approach is to speed up the method life cycle by performing only one quantitative validation step in the final environment of method use. A Supercritical Fluid Chromatography (SFC) method previously developed was used as a case study in this work. Moreover, the interest of geometric transfer was investigated simultaneously in order to stress a little bit more the transfer exercise and, by the way, emphasize the additional benefit of DS strategy in this particular context. Three successful transfers were performed on two column geometries. In order to compare original and transferred methods, the observed relative retention times (RT) were modelled as a function of the predicted relative RT and of the method type (original or transferred). The observed relative RT of the original and transferred methods are not statistically different and thus the method transfer is successfully achieved thanks to the robust optimization strategy. Furthermore, the analytical method was improved considering analysis time (reduced five times) and peak capacity (increased three times). To conclude, the advantage of using a DS strategy implemented for the optimization and transfer of SFC method was successfully demonstrated in this work.

  12. Practical optimization of Steiner trees via the cavity method

    Science.gov (United States)

    Braunstein, Alfredo; Muntoni, Anna

    2016-07-01

    The optimization version of the cavity method for single instances, called Max-Sum, has been applied in the past to the minimum Steiner tree problem on graphs and variants. Max-Sum has been shown experimentally to give asymptotically optimal results on certain types of weighted random graphs, and to give good solutions in short computation times for some types of real networks. However, the hypotheses behind the formulation and the cavity method itself limit substantially the class of instances on which the approach gives good results (or even converges). Moreover, in the standard model formulation, the diameter of the tree solution is limited by a predefined bound, that affects both computation time and convergence properties. In this work we describe two main enhancements to the Max-Sum equations to be able to cope with optimization of real-world instances. First, we develop an alternative ‘flat’ model formulation that allows the relevant configuration space to be reduced substantially, making the approach feasible on instances with large solution diameter, in particular when the number of terminal nodes is small. Second, we propose an integration between Max-Sum and three greedy heuristics. This integration allows Max-Sum to be transformed into a highly competitive self-contained algorithm, in which a feasible solution is given at each step of the iterative procedure. Part of this development participated in the 2014 DIMACS Challenge on Steiner problems, and we report the results here. The performance on the challenge of the proposed approach was highly satisfactory: it maintained a small gap to the best bound in most cases, and obtained the best results on several instances in two different categories. We also present several improvements with respect to the version of the algorithm that participated in the competition, including new best solutions for some of the instances of the challenge.

  13. Optimal experimental design with the sigma point method.

    Science.gov (United States)

    Schenkendorf, R; Kremling, A; Mangold, M

    2009-01-01

    Using mathematical models for a quantitative description of dynamical systems requires the identification of uncertain parameters by minimising the difference between simulation and measurement. Owing to the measurement noise also, the estimated parameters possess an uncertainty expressed by their variances. To obtain highly predictive models, very precise parameters are needed. The optimal experimental design (OED) as a numerical optimisation method is used to reduce the parameter uncertainty by minimising the parameter variances iteratively. A frequently applied method to define a cost function for OED is based on the inverse of the Fisher information matrix. The application of this traditional method has at least two shortcomings for models that are nonlinear in their parameters: (i) it gives only a lower bound of the parameter variances and (ii) the bias of the estimator is neglected. Here, the authors show that by applying the sigma point (SP) method a better approximation of characteristic values of the parameter statistics can be obtained, which has a direct benefit on OED. An additional advantage of the SP method is that it can also be used to investigate the influence of the parameter uncertainties on the simulation results. The SP method is demonstrated for the example of a widely used biological model.

  14. Enhanced Multi-Objective Energy Optimization by a Signaling Method

    Directory of Open Access Journals (Sweden)

    João Soares

    2016-10-01

    Full Text Available In this paper three metaheuristics are used to solve a smart grid multi-objective energy management problem with conflictive design: how to maximize profits and minimize carbon dioxide (CO2 emissions, and the results compared. The metaheuristics implemented are: weighted particle swarm optimization (W-PSO, multi-objective particle swarm optimization (MOPSO and non-dominated sorting genetic algorithm II (NSGA-II. The performance of these methods with the use of multi-dimensional signaling is also compared with this technique, which has previously been shown to boost metaheuristics performance for single-objective problems. Hence, multi-dimensional signaling is adapted and implemented here for the proposed multi-objective problem. In addition, parallel computing is used to mitigate the methods’ computational execution time. To validate the proposed techniques, a realistic case study for a chosen area of the northern region of Portugal is considered, namely part of Vila Real distribution grid (233-bus. It is assumed that this grid is managed by an energy aggregator entity, with reasonable amount of electric vehicles (EVs, several distributed generation (DG, customers with demand response (DR contracts and energy storage systems (ESS. The considered case study characteristics took into account several reported research works with projections for 2020 and 2050. The findings strongly suggest that the signaling method clearly improves the results and the Pareto front region quality.

  15. Optimization of process condition of nanosilica production by hydrothermal method

    Science.gov (United States)

    Qisti, N.; Indrasti, N. S.; Suprihatin

    2016-11-01

    Bagasse ashes have high silica content thus it can be used in nanosilicaproduction to increase its benefit value. This study aimed to get the best time for synthesis and to determine the optimum synthesis time and temperature. This study used the hydrothermal method, a simple method with relatively low reaction temperature and provide a good chemical homogeneity. Time varieties in synthesizing silica were 8,10 and 12 hours, at the temperature of 150 °C. But the results were not as expected. Moreover, optimization of synthesis temperature and time used 4 hours at the temperature of 150 °C based on previous studies. Optimization was conducted using the Response Surface Methodology (RSM). Later, a testusing PSA (Particle Size Analyzer) was performed to obtain particle sizes and PDI values (Polydispersity Index). The results showed that the prediction model of temperature synthesis was 152.67 °C synthesis time of 6 hours, particle size of 276.288 nm and PDI value of 0.189642. The tests showed that the size of particle obtained was 330.39 nm and PDI value at 0.3580. Actual results and predicted results were not significant different.

  16. Using tailored methodical approaches to achieve optimal science outcomes

    Science.gov (United States)

    Wingate, Lory M.

    2016-08-01

    The science community is actively engaged in research, development, and construction of instrumentation projects that they anticipate will lead to new science discoveries. There appears to be very strong link between the quality of the activities used to complete these projects, and having a fully functioning science instrument that will facilitate these investigations.[2] The combination of using internationally recognized standards within the disciplines of project management (PM) and systems engineering (SE) has been demonstrated to lead to achievement of positive net effects and optimal project outcomes. Conversely, unstructured, poorly managed projects will lead to unpredictable, suboptimal project outcomes ultimately affecting the quality of the science that can be done with the new instruments. The proposed application of these two specific methodical approaches, implemented as a tailorable suite of processes, are presented in this paper. Project management (PM) is accepted worldwide as an effective methodology used to control project cost, schedule, and scope. Systems engineering (SE) is an accepted method that is used to ensure that the outcomes of a project match the intent of the stakeholders, or if they diverge, that the changes are understood, captured, and controlled. An appropriate application, or tailoring, of these disciplines can be the foundation upon which success in projects that support science can be optimized.

  17. Construction of optimal supersaturated designs by the packing method

    Institute of Scientific and Technical Information of China (English)

    FANG; Kaitai; GE; Gennian; LIU; Minqian

    2004-01-01

    A supersaturated design is essentially a factorial design with the equal occurrence of levels property and no fully aliased factors in which the number of main efits potential in factor screening experiments. A packing design is an important object in combinatorial design theory. In this paper, a strong link between the two apparently unrelated kinds of designs is shown. Several criteria for comparing supersaturated designs are proposed, their properties and connections with other existing criteria are discussed.A combinatorial approach, called the packing method, for constructing optimal supersaturated designs is presented, and properties of the resulting designs are also investigated.Comparisons between the new designs and other existing designs are given, which show that our construction method and the newly constructed designs have good properties.

  18. PARAMETER OPTIMIZATION OF CARBIDIC AUSTEMPERED DUCTILE IRON USING TAGUCHI METHOD

    Directory of Open Access Journals (Sweden)

    P.DHANAPAL

    2010-08-01

    Full Text Available Carbidic austempered ductile iron [CADI] is the family of ductile iron containing wear resistance alloy carbides in the ausferrite matrix. This CADI is manufactured by selecting proper material composition through the melting route.In an effort to obtain the optimal production parameters, Taguchi method is applied. To analyse the effect of production parameters on the machanical properties, signal-to-noise (S/N ratio is calculated based on the design ofexperiments and the linear graph. The analysis of varience is calculated to find the amount of contribution of factors on individual mechanical properties and its significancy. The analytical results of taguchi method are compared with the experimental values, and it shows both are identical.

  19. Methods for Optimizing CRISPR-Cas9 Genome Editing Specificity.

    Science.gov (United States)

    Tycko, Josh; Myer, Vic E; Hsu, Patrick D

    2016-08-04

    Advances in the development of delivery, repair, and specificity strategies for the CRISPR-Cas9 genome engineering toolbox are helping researchers understand gene function with unprecedented precision and sensitivity. CRISPR-Cas9 also holds enormous therapeutic potential for the treatment of genetic disorders by directly correcting disease-causing mutations. Although the Cas9 protein has been shown to bind and cleave DNA at off-target sites, the field of Cas9 specificity is rapidly progressing, with marked improvements in guide RNA selection, protein and guide engineering, novel enzymes, and off-target detection methods. We review important challenges and breakthroughs in the field as a comprehensive practical guide to interested users of genome editing technologies, highlighting key tools and strategies for optimizing specificity. The genome editing community should now strive to standardize such methods for measuring and reporting off-target activity, while keeping in mind that the goal for specificity should be continued improvement and vigilance.

  20. Comparison of operation optimization methods in energy system modelling

    DEFF Research Database (Denmark)

    Ommen, Torben Schmidt; Markussen, Wiebke Brix; Elmegaard, Brian

    2013-01-01

    , possibilities for decoupling production constraints may be valuable. Introduction of heat pumps in the district heating network may pose this ability. In order to evaluate if the introduction of heat pumps is economically viable, we develop calculation methods for the operation patterns of each of the used...... energy technologies. In the paper, three frequently used operation optimization methods are examined with respect to their impact on operation management of the combined technologies. One of the investigated approaches utilises linear programming for optimisation, one uses linear programming with binary...... operation constraints, while the third approach uses nonlinear programming. In the present case the non-linearity occurs in the boiler efficiency of power plants and the cv-value of an extraction plant. The linear programming model is used as a benchmark, as this type is frequently used, and has the lowest...

  1. Optimal PMU placement using topology transformation method in power systems.

    Science.gov (United States)

    Rahman, Nadia H A; Zobaa, Ahmed F

    2016-09-01

    Optimal phasor measurement units (PMUs) placement involves the process of minimizing the number of PMUs needed while ensuring the entire power system completely observable. A power system is identified observable when the voltages of all buses in the power system are known. This paper proposes selection rules for topology transformation method that involves a merging process of zero-injection bus with one of its neighbors. The result from the merging process is influenced by the selection of bus selected to merge with the zero-injection bus. The proposed method will determine the best candidate bus to merge with zero-injection bus according to the three rules created in order to determine the minimum number of PMUs required for full observability of the power system. In addition, this paper also considered the case of power flow measurements. The problem is formulated as integer linear programming (ILP). The simulation for the proposed method is tested by using MATLAB for different IEEE bus systems. The explanation of the proposed method is demonstrated by using IEEE 14-bus system. The results obtained in this paper proved the effectiveness of the proposed method since the number of PMUs obtained is comparable with other available techniques.

  2. Topology optimization using bi-directional evolutionary structural optimization based on the element-free Galerkin method

    Science.gov (United States)

    Shobeiri, Vahid

    2016-03-01

    In this article, the bi-directional evolutionary structural optimization (BESO) method based on the element-free Galerkin (EFG) method is presented for topology optimization of continuum structures. The mathematical formulation of the topology optimization is developed considering the nodal strain energy as the design variable and the minimization of compliance as the objective function. The EFG method is used to derive the shape functions using the moving least squares approximation. The essential boundary conditions are enforced by the method of Lagrange multipliers. Several topology optimization problems are presented to show the effectiveness of the proposed method. Many issues related to topology optimization of continuum structures, such as chequerboard patterns and mesh dependency, are studied in the examples.

  3. Optimal grid-based methods for thin film micromagnetics simulations

    Science.gov (United States)

    Muratov, C. B.; Osipov, V. V.

    2006-08-01

    Thin film micromagnetics are a broad class of materials with many technological applications, primarily in magnetic memory. The dynamics of the magnetization distribution in these materials is traditionally modeled by the Landau-Lifshitz-Gilbert (LLG) equation. Numerical simulations of the LLG equation are complicated by the need to compute the stray field due to the inhomogeneities in the magnetization which presents the chief bottleneck for the simulation speed. Here, we introduce a new method for computing the stray field in a sample for a reduced model of ultra-thin film micromagnetics. The method uses a recently proposed idea of optimal finite difference grids for approximating Neumann-to-Dirichlet maps and has an advantage of being able to use non-uniform discretization in the film plane, as well as an efficient way of dealing with the boundary conditions at infinity for the stray field. We present several examples of the method's implementation and give a detailed comparison of its performance for studying domain wall structures compared to the conventional FFT-based methods.

  4. Development of an optimal velocity selection method with velocity obstacle

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Min Geuk; Oh, Jun Ho [KAIST, Daejeon (Korea, Republic of)

    2015-08-15

    The Velocity obstacle (VO) method is one of the most well-known methods for local path planning, allowing consideration of dynamic obstacles and unexpected obstacles. Typical VO methods separate a velocity map into a collision area and a collision-free area. A robot can avoid collisions by selecting its velocity from within the collision-free area. However, if there are numerous obstacles near a robot, the robot will have very few velocity candidates. In this paper, a method for choosing optimal velocity components using the concept of pass-time and vertical clearance is proposed for the efficient movement of a robot. The pass-time is the time required for a robot to pass by an obstacle. By generating a latticized available velocity map for a robot, each velocity component can be evaluated using a cost function that considers the pass-time and other aspects. From the output of the cost function, even a velocity component that will cause a collision in the future can be chosen as a final velocity if the pass-time is sufficiently long enough.

  5. Optimization Method for Girder of Wind Turbine Blade

    Directory of Open Access Journals (Sweden)

    Yuqiao Zheng

    2014-01-01

    Full Text Available This paper presents a recently developed numerical multidisciplinary optimization method for design of wind turbine blade. The objective was the highest possible blade weight under specified atmospheric conditions, determined by the design giving girder layer and location parameter. Wind turbine blade on box-section beams girder is calculated by ply thickness, main girder and trailing edge. In this study, a realistic 30 m blade from a 1.2 MW wind turbine model of blade girder parameters is established. The optimization evolves a structure which transforms along the length of the blade, changing from a design with spar caps at the maximum thickness and a trailing edge mass to a design with spar caps toward the tip. In addition, the cross-section structural properties and the modal characteristics of a 62 m rotor blade were predicted by the developed beam finite element. In summary, these findings indicate that the conventional structural layout of a wind turbine blade is suboptimal under the static load conditions, suggesting an opportunity to reduce blade weight and cost.

  6. Process parameter optimization for fly ash brick by Taguchi method

    Energy Technology Data Exchange (ETDEWEB)

    Prabir Kumar Chaulia; Reeta Das [Central Mechanical Engineering Research Institute, Durgapur (India)

    2008-04-15

    This paper presents the results of an experimental investigation carried out to optimize the mix proportions of the fly ash brick by Taguchi method of parameter design. The experiments have been designed using an L9 orthogonal array with four factors and three levels each. Small quantity of cement has been mixed as binding materials. Both cement and the fly ash used are indicated as binding material and water binder ratio has been considered as one of the control factors. So the effects of water/binder ratio, fly ash, coarse sand, and stone dust on the performance characteristic are analyzed using signal-to-noise ratios and mean response data. According to the results, water/binder ratio and stone dust play the significant role on the compressive strength of the brick. Furthermore, the estimated optimum values of the process parameters are corresponding to water/binder ratio of 0.4, fly ash of 39%, coarse sand of 24% and stone dust of 30%. The mean value of optimal strength is predicted as 166.22 kg.cm{sup -2} with a tolerance of 10.97 kg.cm{sup -2}. The confirmatory experimental result obtained for the optimum conditions is 160.17 kg.cm{sup -2}. 13 refs., 3 figs., 7 tabs.

  7. A hybrid method for optimization of the adaptive Goldstein filter

    Science.gov (United States)

    Jiang, Mi; Ding, Xiaoli; Tian, Xin; Malhotra, Rakesh; Kong, Weixue

    2014-12-01

    The Goldstein filter is a well-known filter for interferometric filtering in the frequency domain. The main parameter of this filter, alpha, is set as a power of the filtering function. Depending on it, considered areas are strongly or weakly filtered. Several variants have been developed to adaptively determine alpha using different indicators such as the coherence, and phase standard deviation. The common objective of these methods is to prevent areas with low noise from being over filtered while simultaneously allowing stronger filtering over areas with high noise. However, the estimators of these indicators are biased in the real world and the optimal model to accurately determine the functional relationship between the indicators and alpha is also not clear. As a result, the filter always under- or over-filters and is rarely correct. The study presented in this paper aims to achieve accurate alpha estimation by correcting the biased estimator using homogeneous pixel selection and bootstrapping algorithms, and by developing an optimal nonlinear model to determine alpha. In addition, an iteration is also merged into the filtering procedure to suppress the high noise over incoherent areas. The experimental results from synthetic and real data show that the new filter works well under a variety of conditions and offers better and more reliable performance when compared to existing approaches.

  8. Method for Cleaning Laser-Drilled Holes on Printed Wiring Boards by Plasma Treatment

    Science.gov (United States)

    Hirogaki, Toshiki; Aoyama, Eiichi; Minagi, Ryu; Ogawa, Keiji; Katayama, Tsutao; Matsuoka, Takashi; Inoue, Hisahiro

    We propose a new method for cleaning blind via holes after laser drilling of PWBs using oxygen plasma treatment. This report dealt with three kinds of PWB materials: epoxy resin and two kinds of aramid fiber reinforced plastics (AFRP: Technora or Kevlar fiber reinforcement). We observed the drilled holes after plasma treatment using both an optical and a scanning electric microscope (SEM). It was confirmed that adequate etching took place in the drilled holes by plasma treatment. We also compared the hole wall and hole bottom after plasma treatment with ones after chemical etching. It was clear that there was no damage to the aramid fiber tip on the hole wall, and that a smooth roughness of the hole wall was obtained by means of plasma treatment. As a result, we demonstrated that the plasma treatment is effective in cleaning the laser drilled holes of PWBs.

  9. A new fuzzy optimal data replication method for data grid

    Directory of Open Access Journals (Sweden)

    Zeinab Ghilavizadeh

    2013-03-01

    Full Text Available These days, There are several applications where we face with large data set and it has become an important part of common resources in different scientific areas. In fact, there are many applications where there are literally huge amount of information handled either in terabyte or in petabyte. Many scientists apply huge amount of data distributed geographically around the world through advanced computing systems. The huge volume data and calculations have created new problems in accessing, processing and distribution of data. The challenges of data management infrastructure have become very difficult under a large amount of data, different geographical spaces, and complicated involved calculations. Data Grid is a remedy to all mentioned problems. In this paper, a new method of dynamic optimal data replication in data grid is introduced where it reduces the total job execution time and increases the locality in accessibilities by detecting and impacting the factors influencing the data replication. Proposed method is composed of two main phases. During the first phase is the phase of file application and replication operation. In this phase, we evaluate three factors influencing the data replication and determine whether the requested file can be replicated or it can be used from distance. In the second phase or the replacement phase, the proposed method investigates whether there is enough space in the destination to store the requested file or not. In this phase, the proposed method also chooses a replica with the lowest value for deletion by considering three replica factors to increase the performance of system. The results of simulation also indicate the improved performance of our proposed method compared with other replication methods represented in the simulator Optorsim.

  10. A Glowworm Optimization Method for the Design of Web Services

    Directory of Open Access Journals (Sweden)

    Koffka Khan

    2012-09-01

    Full Text Available A method for adaptive usability evaluation of B2C eCommerce web services is proposed. For measuring eCommerce usability a checklist integrating eCommerce quality and usability is developed. By a Glowworm swarm optimization (GSO neural networks-based model the usability dimensions and their checklist items are adaptively selected. A case study for usability evaluation of an eCommerce anthurium retail website is carried out. The experimental results show that GSO with neural networks supports the allocation of usability problems and the defining of relevant improvement measures. The main advantage of the approach is the adaptive selection of most significant checklist dimensions and items and thus significant reduction of the time for usability evaluation and design.

  11. Hybrid Neural Network and Support Vector Machine Method for Optimization

    Science.gov (United States)

    Rai, Man Mohan (Inventor)

    2007-01-01

    System and method for optimization of a design associated with a response function, using a hybrid neural net and support vector machine (NN/SVM) analysis to minimize or maximize an objective function, optionally subject to one or more constraints. As a first example, the NN/SVM analysis is applied iteratively to design of an aerodynamic component, such as an airfoil shape, where the objective function measures deviation from a target pressure distribution on the perimeter of the aerodynamic component. As a second example, the NN/SVM analysis is applied to data classification of a sequence of data points in a multidimensional space. The NN/SVM analysis is also applied to data regression.

  12. Gradient type optimization methods for electronic structure calculations

    CERN Document Server

    Zhang, Xin; Wen, Zaiwen; Zhou, Aihui

    2013-01-01

    The density functional theory (DFT) in electronic structure calculations can be formulated as either a nonlinear eigenvalue or direct minimization problem. The most widely used approach for solving the former is the so-called self-consistent field (SCF) iteration. A common observation is that the convergence of SCF is not clear theoretically while approaches with convergence guarantee for solving the latter are often not competitive to SCF numerically. In this paper, we study gradient type methods for solving the direct minimization problem by constructing new iterations along the gradient on the Stiefel manifold. Global convergence (i.e., convergence to a stationary point from any initial solution) as well as local convergence rate follows from the standard theory for optimization on manifold directly. A major computational advantage is that the computation of linear eigenvalue problems is no longer needed. The main costs of our approaches arise from the assembling of the total energy functional and its grad...

  13. Shape optimized headers and methods of manufacture thereof

    Science.gov (United States)

    Perrin, Ian James

    2013-11-05

    Disclosed herein is a shape optimized header comprising a shell that is operative for collecting a fluid; wherein an internal diameter and/or a wall thickness of the shell vary with a change in pressure and/or a change in a fluid flow rate in the shell; and tubes; wherein the tubes are in communication with the shell and are operative to transfer fluid into the shell. Disclosed herein is a method comprising fixedly attaching tubes to a shell; wherein the shell is operative for collecting a fluid; wherein an internal diameter and/or a wall thickness of the shell vary with a change in pressure and/or a change in a fluid flow rate in the shell; and wherein the tubes are in communication with the shell and are operative to transfer fluid into the shell.

  14. Convex functions and optimization methods on Riemannian manifolds

    CERN Document Server

    Udrişte, Constantin

    1994-01-01

    This unique monograph discusses the interaction between Riemannian geometry, convex programming, numerical analysis, dynamical systems and mathematical modelling. The book is the first account of the development of this subject as it emerged at the beginning of the 'seventies. A unified theory of convexity of functions, dynamical systems and optimization methods on Riemannian manifolds is also presented. Topics covered include geodesics and completeness of Riemannian manifolds, variations of the p-energy of a curve and Jacobi fields, convex programs on Riemannian manifolds, geometrical constructions of convex functions, flows and energies, applications of convexity, descent algorithms on Riemannian manifolds, TC and TP programs for calculations and plots, all allowing the user to explore and experiment interactively with real life problems in the language of Riemannian geometry. An appendix is devoted to convexity and completeness in Finsler manifolds. For students and researchers in such diverse fields as pu...

  15. [Optimization for determination methods of alpha-, beta- carotene in vegetables].

    Science.gov (United States)

    Cao, Mengjin; Zhang, Xuesong; Wang, Xiaojiig; Shen, Xiang; Wang, Zhu

    2016-05-01

    To optimize the determination method of carotene in order to separate the alpha and beta carotene. The homogenized samples were extracted with ethanol before saponification, and then extracted with petroleum ether followed by wash, dry and concentration. At last, the separation was performed on the high performance liquid chromatographic with YMC Carotenoid C30 column (3 microm 4.6 mm x 150 mm). The mobile phase was consisted of A (methanol: acetonitrile: water = 73.5: 24.5:2) and B (methyl tert-butyl ether), with a linear gradient elution. The detection wavelength was 450 nm. The C30-HPLC column was used throughout the experiment exhibiting a significant benefit for the separation of carotienes and isomers. Multifactor analysis of variance showed that heating by the anhydrous ethyl alcohol before the saponification was more suitable for extracting the carotenoids from vegetables. Under the optimal condition, the linear range of alpha-carotene was 0.495-9.90 microg/mL, and all-trans-beta-carotene was 0.552-10.4 microg/mL, with the linear correlation coefficient were above 0. 999. The relative standard deviation for the alpha and beta carotene were less than 10% (n = 6). The average spike recoveries for alpha and beta carotene in vegetables were 81.6%-93.3%. The detection and quantification limits for alpha and beta carotene were 0.5 microg/100 g and 1.5 microg/100 g, respectively, when taking 5g samples. The method is accurate, reliable, and fit for analyzing alpha-carotene and beta-carotene in fresh vegetables.

  16. An automatic and effective parameter optimization method for model tuning

    Directory of Open Access Journals (Sweden)

    T. Zhang

    2015-05-01

    Full Text Available Physical parameterizations in General Circulation Models (GCMs, having various uncertain parameters, greatly impact model performance and model climate sensitivity. Traditional manual and empirical tuning of these parameters is time consuming and ineffective. In this study, a "three-step" methodology is proposed to automatically and effectively obtain the optimum combination of some key parameters in cloud and convective parameterizations according to a comprehensive objective evaluation metrics. Different from the traditional optimization methods, two extra steps, one determines parameter sensitivity and the other chooses the optimum initial value of sensitive parameters, are introduced before the downhill simplex method to reduce the computational cost and improve the tuning performance. Atmospheric GCM simulation results show that the optimum combination of these parameters determined using this method is able to improve the model's overall performance by 9%. The proposed methodology and software framework can be easily applied to other GCMs to speed up the model development process, especially regarding unavoidable comprehensive parameters tuning during the model development stage.

  17. Optimizing restriction fragment fingerprinting methods for ordering large genomic libraries.

    Science.gov (United States)

    Branscomb, E; Slezak, T; Pae, R; Galas, D; Carrano, A V; Waterman, M

    1990-10-01

    We present a statistical analysis of the problem of ordering large genomic cloned libraries through overlap detection based on restriction fingerprinting. Such ordering projects involve a large investment of effort involving many repetitious experiments. Our primary purpose here is to provide methods of maximizing the efficiency of such efforts. To this end, we adopt a statistical approach that uses the likelihood ratio as a statistic to detect overlap. The main advantages of this approach are that (1) it allows the relatively straightforward incorporation of the observed statistical properties of the data; (2) it permits the efficiency of a particular experimental method for detecting overlap to be quantitatively defined so that alternative experimental designs may be compared and optimized; and (3) it yields a direct estimate of the probability that any two library members overlap. This estimate is a critical tool for the accurate, automatic assembly of overlapping sets of fragments into islands called "contigs." These contigs must subsequently be connected by other methods to provide an ordered set of overlapping fragments covering the entire genome.

  18. A Nature-Inspired Optimization-Based Optimum Fuzzy Logic Photovoltaic Inverter Controller Utilizing an eZdsp F28335 Board

    Directory of Open Access Journals (Sweden)

    Ammar Hussein Mutlag

    2016-02-01

    Full Text Available Photovoltaic (PV inverters essentially convert DC quantities, such as voltage and current, to AC quantities whose magnitude and frequency are controlled to obtain the desired output. Thus, the performance of an inverter depends on its controller. Therefore, an optimum fuzzy logic controller (FLC design technique for PV inverters using a lightning search algorithm (LSA is presented in this study. In a conventional FLC, the procedure for obtaining membership functions (MFs is usually implemented using trial and error, which does not lead to satisfactory solutions in many cases. Therefore, this study presents a technique for obtaining MFs that avoids the exhaustive traditional trial-and-error procedure. This technique is implemented during the inverter design phase by generating adaptive MFs based on the evaluation results of the objective function formulated with LSA. The mean squared error (MSE of the inverter output voltage is used as an objective function in this study. LSA optimizes the MFs such that the inverter provides the lowest MSE for the output voltage, and the performance of the PV inverter output is improved in terms of amplitude and frequency. First, the design procedure and accuracy of the optimum FLC are illustrated and investigated through simulations conducted in a MATLAB environment. The LSA-based FLC (LSA-FL are compared with differential search algorithm (DSA-based FLC (DSA-FL and particle swarm optimization (PSO-based FLC (PSO-FL. Finally, the robustness of the LSA-FL is further investigated with a hardware that is operated via an eZdsp F28335 control board. Simulation and experimental results show that the proposed controller can successfully obtain the desired output when different loads are connected to the system. The inverter also has a reasonably low steady-state error and fast response to reference variation.

  19. Triboelectric separation technology for removing inorganics from non-metallic fraction of waste printed circuit boards: Influence of size fraction and process optimization.

    Science.gov (United States)

    Zhang, Guangwen; Wang, Haifeng; He, Yaqun; Yang, Xing; Peng, Zhen; Zhang, Tao; Wang, Shuai

    2017-02-01

    Removing inorganics from non-metallic fraction (NMF) of waste printed circuit boards (WPCBs) is an effective mean to improve its usability. The effect of size fraction on the triboelectric separation of NMF of WPCBs was investigated in a lab triboelectric separation system and the separation process was optimized in this paper. The elements distribution in raw NMF collected from typical WPCBs recycling plant and each size fraction obtained by sieving were analyzed by X-ray fluorescence (XRF). The results show that the main inorganic elements in NMF are P, Ba, Mn, Sb, Ti, Pb, Zn, Sn, Mg, Fe, Ca, Cu, Al and Si. The inorganic content of each size fraction increased with the size decreasing. The metal elements are mainly distributed in -0.2mm size fraction, and concentrated in middle product of triboelectric separation. The loss on ignition (LOI) of positive product and negative product is higher than that of the middle product for the -0.355mm size fraction, while the LOI presents gradually increasing trend from negative to positive plate for the +0.355mm size fraction. Based on the separation results and mineralogical characterizations of each size fraction of NMF, the pretreatment process including several mineral processing operations was added before triboelectric separation and better separation result was obtained. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. OPTIMIZATION METHOD FOR VIRTUAL PRODUCT DEVELOPMENT BASED ON SIMULATION METAMODEL AND ITS APPLICATION

    Institute of Scientific and Technical Information of China (English)

    Pan Jun; Fan Xiumin; Ma Dengzhe; Jin Ye

    2003-01-01

    Virtual product development (VPD) is essentially based on simulation. Due to computational inefficiency, traditional engineering simulation software and optimization methods are inadequate to analyze optimization problems in VPD. Optimization method based on simulation metamodel for virtual product development is proposed to satisfy the needs of complex optimal designs driven by VPD. This method extends the current design of experiments (DOE) by various metamodeling technologies. Simulation metamodels are built to approximate detailed simulation codes, so as to provide link between optimization and simulation, or serve as a bridge for simulation software integration among different domains. An example of optimal design for composite material structure is used to demonstrate the newly introduced method.

  1. Optimization of hydrofoil for tidal current turbine based on particle swarm optimization and computational fluid dynamic method

    OpenAIRE

    Zhang De-Sheng; Chen Jian; Shi Wei-Dong; Shi Lei; Geng Lin-Lin

    2016-01-01

    Both efficiency and cavitation performance of the hydrofoil are the key technologies to design the tidal current turbine. In this paper, the hydrofoil efficiency and lift coefficient were improved based on particle swarm optimization method and XFoil codes. The cavitation performance of the optimized hydrofoil was also discussed by the computational fluid dynamic. Numerical results show the efficiency of the optimized hydrofoil was improved 11% ranging from...

  2. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>2011-2015 The World Journal of Diabetes Editorial Board now consists of 710 members,representing a team of worldwide experts in diabetes mellitus.They are from 56 countries,including Argentina(2),Australia(27),Austria(11),

  3. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 529 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 40 countries, including Argentina (1), Australia (7),

  4. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 529 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7),

  5. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 523 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7),

  6. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2009-2013The World Journal of Biological Chemistry Editorial Board consists of 529 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 40 countries, including Argentina (1), Australia (7),

  7. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    2011-2015 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 411 members, representing a team of worldwide experts in surgery research. They are from 47 countries, including Argentina (3),

  8. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    2011-2015 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 411 members, representing a team of worldwide experts in surgery research.They are from 47 countries,including Argentina(3),

  9. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 529 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7),

  10. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members,representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research.They are from 36 countries,

  11. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members,representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research. They are from

  12. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members,representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research.They are from 36 countries,

  13. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members, representing a team of worldwide experts in pharmacology and therapeutics research. They are from 36 countries, including Australia (6), Austria (2),

  14. Classification and uptake of reservoir operation optimization methods

    Science.gov (United States)

    Dobson, Barnaby; Pianosi, Francesca; Wagener, Thorsten

    2016-04-01

    Reservoir operation optimization algorithms aim to improve the quality of reservoir release and transfer decisions. They achieve this by creating and optimizing the reservoir operating policy; a function that returns decisions based on the current system state. A range of mathematical optimization algorithms and techniques has been applied to the reservoir operation problem of policy optimization. In this work, we propose a classification of reservoir optimization approaches by focusing on the formulation of the water management problem rather than the optimization algorithm type. We believe that decision makers and operators will find it easier to navigate a classification system based on the problem characteristics, something they can clearly define, rather than the optimization algorithm. Part of this study includes an investigation regarding the extent of algorithm uptake and the possible reasons that limit real world application.

  15. Optimization of Bending Process Parameters for Seamless Tubes Using Taguchi Method and Finite Element Method

    Directory of Open Access Journals (Sweden)

    Jui-Chang Lin

    2015-01-01

    Full Text Available The three-dimensional tube (or pipe is manufactured by CNC tube bending machine. The key techniques are determined by tube diameter, wall thickness, material, and bending radius. The obtained technique through experience and the trial and error method is unreliable. Finite element method (FEM simulation for the tube bending process before production can avoid wasting manpower and raw materials. The computer-aided engineering (CAE software ABAQUS 6.12 is applied to simulate bending characteristics and to explore the maximum stress and strain conditions. The Taguchi method is used to find the optimal parameters of bending. The confirmation experiment is performed according to optimal parameters. Results indicate that the strain error between CAE simulation and bending experiments is within 6.39%.

  16. The Networked Manufacturing Resources Optimizing Configuration System and Its Partners Selection Method

    Institute of Scientific and Technical Information of China (English)

    DONG Zhao-yang; SUN Shu-dong

    2006-01-01

    The three levels optimizing strategy is put forward for the networked manufacturing resources optimizing configuration, namely, the optimizing of a logical manufacturing process,the optimizing of simulation-based integration of process planning and scheduling, and the optimizing of networked production scheduling. Then, the web services-based architecture of networked manufacturing resources optimizing configuration is brought forward. Finally, the key algorithm of the networked manufacturing resources optimizing configuration is discussed, namely, the two phases manufacturing partners selection method, which including the group technology-based manufacturing resources pre-configuration and the genetic algorithm-based executable manufacturing process optimizing.

  17. Pipeline heating method based on optimal control and state estimation

    Energy Technology Data Exchange (ETDEWEB)

    Vianna, F.L.V. [Dept. of Subsea Technology. Petrobras Research and Development Center - CENPES, Rio de Janeiro, RJ (Brazil)], e-mail: fvianna@petrobras.com.br; Orlande, H.R.B. [Dept. of Mechanical Engineering. POLI/COPPE, Federal University of Rio de Janeiro - UFRJ, Rio de Janeiro, RJ (Brazil)], e-mail: helcio@mecanica.ufrj.br; Dulikravich, G.S. [Dept. of Mechanical and Materials Engineering. Florida International University - FIU, Miami, FL (United States)], e-mail: dulikrav@fiu.edu

    2010-07-01

    In production of oil and gas wells in deep waters the flowing of hydrocarbon through pipeline is a challenging problem. This environment presents high hydrostatic pressures and low sea bed temperatures, which can favor the formation of solid deposits that in critical operating conditions, as unplanned shutdown conditions, may result in a pipeline blockage and consequently incur in large financial losses. There are different methods to protect the system, but nowadays thermal insulation and chemical injection are the standard solutions normally used. An alternative method of flow assurance is to heat the pipeline. This concept, which is known as active heating system, aims at heating the produced fluid temperature above a safe reference level in order to avoid the formation of solid deposits. The objective of this paper is to introduce a Bayesian statistical approach for the state estimation problem, in which the state variables are considered as the transient temperatures within a pipeline cross-section, and to use the optimal control theory as a design tool for a typical heating system during a simulated shutdown condition. An application example is presented to illustrate how Bayesian filters can be used to reconstruct the temperature field from temperature measurements supposedly available on the external surface of the pipeline. The temperatures predicted with the Bayesian filter are then utilized in a control approach for a heating system used to maintain the temperature within the pipeline above the critical temperature of formation of solid deposits. The physical problem consists of a pipeline cross section represented by a circular domain with four points over the pipe wall representing heating cables. The fluid is considered stagnant, homogeneous, isotropic and with constant thermo-physical properties. The mathematical formulation governing the direct problem was solved with the finite volume method and for the solution of the state estimation problem

  18. Optimized protein extraction methods for proteomic analysis of Rhizoctonia solani.

    Science.gov (United States)

    Lakshman, Dilip K; Natarajan, Savithiry S; Lakshman, Sukla; Garrett, Wesley M; Dhar, Arun K

    2008-01-01

    Rhizoctonia solani (Teleomorph: Thanatephorus cucumeris, T. praticola) is a basidiomycetous fungus and a major cause of root diseases of economically important plants. Various isolates of this fungus are also beneficially associated with orchids, may serve as biocontrol agents or remain as saprophytes with roles in decaying and recycling of soil organic matter. R. solani displays several hyphal anastomosis groups (AG) with distinct host and pathogenic specializations. Even though there are reports on the physiological and histological basis of Rhizoctonia-host interactions, very little is known about the molecular biology and control of gene expression early during infection by this pathogen. Proteamic technologies are powerful tools for examining alterations in protein profiles. To aid studies on its biology and host pathogen interactions, a two-dimensional (2-D) gel-based global proteomic study has been initiated. To develop an optimized protein extraction protocol for R. solani, we compared two previously reported protein extraction protocols for 2-D gel analysis of R. solani (AG-4) isolate Rs23. Both TCA-acetone precipitation and phosphate solubilization before TCA-acetone precipitation worked well for R. solani protein extraction, although selective enrichment of some proteins was noted with either method. About 450 spots could be detected with the densitiometric tracing of Coomassie blue-stained 2-D PAGE gels covering pH 4-7 and 6.5-205 kDa. Selected protein spots were subjected to mass spectrometric analysis with matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS). Eleven protein spots were positively identified based on peptide mass fingerprinting match with fungal proteins in public databases with the Mascot search engine. These results testify to the suitability of the two optimized protein extraction protocols for 2-D proteomic studies of R. solani.

  19. Proposed optimal LSP selection method in MPLS networks

    CERN Document Server

    Kuribayashi, Shin-ichi

    2012-01-01

    Multi-Protocol Label Switching (MPLS) had been deployed by many data networking service providers, including the next-generation mobile backhaul networks, because of its undeniable potential in terms of virtual private network (VPN) management, traffic engineering, etc. In MPLS networks, IP packets are transmitted along a Label Switched Path (LSP) established between edge nodes. To improve the efficiency of resource use in MPLS networks, it is essential to utilize the LSPs efficiently. This paper proposes a method of selecting the optimal LSP pair from among multiple LSP pairs which are established between the same pair of edge nodes, on the assumption that both the upward and downward LSPs are established as a pair (both-way operation). It is supposed that both upward and downward bandwidths are allocated simultaneously in the selected LSP pair for each service request. It is demonstrated by simulation evaluations that the proposal method could reduce the total amount of the bandwidth required by up to 15% c...

  20. Research on multi-fidelity aerodynamic optimization methods

    Institute of Scientific and Technical Information of China (English)

    Huang Likeng; Gao Zhenghong; Zhang Dehu

    2013-01-01

    Constructing high approximation accuracy surrogate model with lower computational cost has great engineering significance.In this paper,using co-Kriging method,an efficient multifidelity surrogate model is constructed based on two independent high and low fidelity samples.Co-Kriging method can use a greater quantity of low-fidelity information to enhance the accuracy of a surrogate of the high-fidelity model by modeling the correlation between high and low fidelity model,thus computational cost of building surrogate model can be greatly reduced.A wing-body problem is taken as an example to compare characteristics of co-Kriging multi-fidelity (CKMF)model with traditional Kriging based multi-fidelity (KMF) model.A sampling convergence of the CKMF model and the KMF model is conducted,and an appropriate sampling design is selected through the sampling convergence analysis.The results indicate that CKMF model has higher approximation accuracy with the same high-fidelity samples,and converges at less high-fidelity samples.A wing-body drag reduction optimization design using genetic algorithm is implemented.Satisfying design results are obtained,which validate the feasibility of CKMF model in engineering design.

  1. Simple optimization method for partitioning purification of hydrogen networks

    Directory of Open Access Journals (Sweden)

    W.M. Shehata

    2015-03-01

    Full Text Available The Egyptian petroleum fuel market is increasing rapidly nowadays. These fuels must be in the standard specifications of the Egyptian General Petroleum Corporation (EGPC, which required lower sulfur gasoline and diesel fuels. So the fuels must be deep hydrotreated which resulted in increasing hydrogen (H2 consumption for deeper hydrotreating. Along with increased H2 consumption for deeper hydrotreating, additional H2 is needed for processing heavier and higher sulfur crude slates especially in hydrocracking process, in addition to hydrotreating unit, isomerization units and lubricant plants. Purification technology is used to increase the amount of recycled hydrogen. If the amount of recycled hydrogen is increased, the amount of hydrogen that is sent to the furnaces with the off gas will decrease. In this work, El Halwagi et al. (2003 and El Halwagi (2012 optimization methods which are used for recycle/reuse integration systems have been extended to be used in the partitioning purification of hydrogen networks to minimize the hydrogen consumption and the hydrogen discharge. An actual case study and two case studies from the literature are solved to illustrate the proposed method.

  2. Martian Radiative Transfer Modeling Using the Optimal Spectral Sampling Method

    Science.gov (United States)

    Eluszkiewicz, J.; Cady-Pereira, K.; Uymin, G.; Moncet, J.-L.

    2005-01-01

    The large volume of existing and planned infrared observations of Mars have prompted the development of a new martian radiative transfer model that could be used in the retrievals of atmospheric and surface properties. The model is based on the Optimal Spectral Sampling (OSS) method [1]. The method is a fast and accurate monochromatic technique applicable to a wide range of remote sensing platforms (from microwave to UV) and was originally developed for the real-time processing of infrared and microwave data acquired by instruments aboard the satellites forming part of the next-generation global weather satellite system NPOESS (National Polarorbiting Operational Satellite System) [2]. As part of our on-going research related to the radiative properties of the martian polar caps, we have begun the development of a martian OSS model with the goal of using it to perform self-consistent atmospheric corrections necessary to retrieve caps emissivity from the Thermal Emission Spectrometer (TES) spectra. While the caps will provide the initial focus area for applying the new model, it is hoped that the model will be of interest to the wider Mars remote sensing community.

  3. Growing string method with interpolation and optimization in internal coordinates: method and examples.

    Science.gov (United States)

    Zimmerman, Paul M

    2013-05-14

    The growing string method (GSM) has proven especially useful for locating chemical reaction paths at low computational cost. While many string methods use Cartesian coordinates, these methods can be substantially improved by changes in the coordinate system used for interpolation and optimization steps. The quality of the interpolation scheme is especially important because it determines how close the initial path is to the optimized reaction path, and this strongly affects the rate of convergence. In this article, a detailed description of the generation of internal coordinates (ICs) suitable for use in GSM as reactive tangents and in string optimization is given. Convergence of reaction paths is smooth because the IC tangent and orthogonal directions are better representations of chemical bonding compared to Cartesian coordinates. This is not only important quantitatively for reducing computational cost but also allows reaction paths to be described with smoothly varying chemically relevant coordinates. Benchmark computations with challenging reactions are compared to previous versions of GSM and show significant speedups. Finally, a climbing image scheme is included to improve the quality of the transition state approximation, ensuring high reliability of the method.

  4. The Multiobjective Trajectory Optimization for Hypersonic Glide Vehicle Based on Normal Boundary Intersection Method

    OpenAIRE

    Zhengnan Li; Tao Yang; Zhiwei Feng

    2016-01-01

    To solve the multiobjective optimization problem on hypersonic glider vehicle trajectory design subjected to complex constraints, this paper proposes a multiobjective trajectory optimization method that combines the boundary intersection method and pseudospectral method. The multiobjective trajectory optimization problem (MTOP) is established based on the analysis of the feature of hypersonic glider vehicle trajectory. The MTOP is translated into a set of general optimization subproblems by u...

  5. Optimal Control with Time Delays via the Penalty Method

    Directory of Open Access Journals (Sweden)

    Mohammed Benharrat

    2014-01-01

    Full Text Available We prove necessary optimality conditions of Euler-Lagrange type for a problem of the calculus of variations with time delays, where the delay in the unknown function is different from the delay in its derivative. Then, a more general optimal control problem with time delays is considered. Main result gives a convergence theorem, allowing us to obtain a solution to the delayed optimal control problem by considering a sequence of delayed problems of the calculus of variations.

  6. Methods and tools for analysis and optimization of power plants

    Energy Technology Data Exchange (ETDEWEB)

    Assadi, Mohsen

    2000-09-01

    The most noticeable advantage of the introduction of the computer-aided tools in the field of power generation, has been the ability to study the plant's performance prior to the construction phase. The results of these studies have made it possible to change and adjust the plant layout to match the pre-defined requirements. Further development of computers in recent years has opened up for implementation of new features in the existing tools and also for the development of new tools for specific applications, like thermodynamic and economic optimization, prediction of the remaining component life time, and fault diagnostics, resulting in improvement of the plant's performance, availability and reliability. The most common tools for pre-design studies are heat and mass balance programs. Further thermodynamic and economic optimization of plant layouts, generated by the heat and mass balance programs, can be accomplished by using pinch programs, exergy analysis and thermoeconomics. Surveillance and fault diagnostics of existing systems can be performed by using tools like condition monitoring systems and artificial neural networks. The increased number of tools and their various construction and application areas make the choice of the most adequate tool for a certain application difficult. In this thesis the development of different categories of tools and techniques, and their application area are reviewed and presented. Case studies on both existing and theoretical power plant layouts have been performed using different commercially available tools to illuminate their advantages and shortcomings. The development of power plant technology and the requirements for new tools and measurement systems have been briefly reviewed. This thesis contains also programming techniques and calculation methods concerning part-load calculations using local linearization, which has been implemented in an inhouse heat and mass balance program developed by the author

  7. Optimized Audio Classification and Segmentation Algorithm by Using Ensemble Methods

    Directory of Open Access Journals (Sweden)

    Saadia Zahid

    2015-01-01

    Full Text Available Audio segmentation is a basis for multimedia content analysis which is the most important and widely used application nowadays. An optimized audio classification and segmentation algorithm is presented in this paper that segments a superimposed audio stream on the basis of its content into four main audio types: pure-speech, music, environment sound, and silence. An algorithm is proposed that preserves important audio content and reduces the misclassification rate without using large amount of training data, which handles noise and is suitable for use for real-time applications. Noise in an audio stream is segmented out as environment sound. A hybrid classification approach is used, bagged support vector machines (SVMs with artificial neural networks (ANNs. Audio stream is classified, firstly, into speech and nonspeech segment by using bagged support vector machines; nonspeech segment is further classified into music and environment sound by using artificial neural networks and lastly, speech segment is classified into silence and pure-speech segments on the basis of rule-based classifier. Minimum data is used for training classifier; ensemble methods are used for minimizing misclassification rate and approximately 98% accurate segments are obtained. A fast and efficient algorithm is designed that can be used with real-time multimedia applications.

  8. Activity optimization method in SPECT: A comparison with ROC analysis

    Institute of Scientific and Technical Information of China (English)

    D(I)AZ Marlén Pérez; RIZO Oscar Díaz; D(I)AZ Adlin López; APARICIO Eric Estévez; D(I)AZ Reinaldo Roque

    2006-01-01

    A discriminant method for optimizing activity in nuclear medicine studies is validated by comparison with ROC performed with a cardiac phantom. Three different lesions (L1, L2 and L3) were placed in the myocardium-wall by pairs for each SPECT. Three activities (84, 37 or 18.5 MBq) of 99mTc were used as background. Linear discriminant analysis was used to select the parameters that characterize image quality among the measured variables in the images [(Background-to-Lesion (B/Li) and Signal-to-Noise (Si/N) ratio s)]. Two clusters with different image quality (P=0.021) were obtained. The ratios B/L1, B/L2 and B/L3are the parameters used to construct the function with 100% of cases correctly classified into the clusters. The value of 37 MBq was the lowest tested activity for which good results for the B/Li ratios were obtained. The result coincides with the applied ROC-analysis (r=0.89).

  9. Influence of Pareto optimality on the maximum entropy methods

    Science.gov (United States)

    Peddavarapu, Sreehari; Sunil, Gujjalapudi Venkata Sai; Raghuraman, S.

    2017-07-01

    Galerkin meshfree schemes are emerging as a viable substitute to finite element method to solve partial differential equations for the large deformations as well as crack propagation problems. However, the introduction of Shanon-Jayne's entropy principle in to the scattered data approximation has deviated from the trend of defining the approximation functions, resulting in maximum entropy approximants. Further in addition to this, an objective functional which controls the degree of locality resulted in Local maximum entropy approximants. These are based on information-theoretical Pareto optimality between entropy and degree of locality that are defining the basis functions to the scattered nodes. The degree of locality in turn relies on the choice of locality parameter and prior (weight) function. The proper choices of both plays vital role in attain the desired accuracy. Present work is focused on the choice of locality parameter which defines the degree of locality and priors: Gaussian, Cubic spline and quartic spline functions on the behavior of local maximum entropy approximants.

  10. Multiobjective Optimization Method Based on Adaptive Parameter Harmony Search Algorithm

    Directory of Open Access Journals (Sweden)

    P. Sabarinath

    2015-01-01

    Full Text Available The present trend in industries is to improve the techniques currently used in design and manufacture of products in order to meet the challenges of the competitive market. The crucial task nowadays is to find the optimal design and machining parameters so as to minimize the production costs. Design optimization involves more numbers of design variables with multiple and conflicting objectives, subjected to complex nonlinear constraints. The complexity of optimal design of machine elements creates the requirement for increasingly effective algorithms. Solving a nonlinear multiobjective optimization problem requires significant computing effort. From the literature it is evident that metaheuristic algorithms are performing better in dealing with multiobjective optimization. In this paper, we extend the recently developed parameter adaptive harmony search algorithm to solve multiobjective design optimization problems using the weighted sum approach. To determine the best weightage set for this analysis, a performance index based on least average error is used to determine the index of each weightage set. The proposed approach is applied to solve a biobjective design optimization of disc brake problem and a newly formulated biobjective design optimization of helical spring problem. The results reveal that the proposed approach is performing better than other algorithms.

  11. Control Methods Utilizing Energy Optimizing Schemes in Refrigeration Systems

    DEFF Research Database (Denmark)

    Larsen, L.S; Thybo, C.; Stoustrup, Jakob;

    2003-01-01

    The potential energy savings in refrigeration systems using energy optimal control has been proved to be substantial. This however requires an intelligent control that drives the refrigeration systems towards the energy optimal state. This paper proposes an approach for a control, which drives...

  12. A METHOD FOR TOPOLOGICAL OPTIMIZATION OF STRUCTURES WITH DISCRETE VARIABLES UNDER DYNAMIC STRESS AND DISPLACEMENT CONSTRAINTS

    Institute of Scientific and Technical Information of China (English)

    石连栓; 孙焕纯; 冯恩民

    2001-01-01

    A method for topological optimization of structures with discrete variables subjected to dynamic stress and displacement constraints is presented. By using the quasistatic method, the structure optimization problem under dynamic stress and displacement constraints is converted into one subjected to static stress and displacement constraints. The comprehensive algorithm for topological optimization of structures with discrete variables is used to find the optimum solution.

  13. Culture medium optimization for pigment production with RSM method

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Response surface methodology was used to optimize a medium for a red-pigmented marine bacterium S-9801 strain (Flavobacterium sp.). In the first optimization step the influence of yeast extract, peptone, glucose and sodium chloride on pigment production was evaluated using a fractional factorial design. Pigment production was positively influenced by glucose and sodium chloride while other components had no significant effect. In the second step the path of steepest ascent was used to approach the optimal region of the medium composition. In the third step the optimal concentration of glucose and sodium chloride was determined by a central composite design and response analysis. The optimized medium allowed pigment production (A 535~650) to be increased from 0.137 to0.559, being 320% higher than the original medium.

  14. Laser: a Tool for Optimization and Enhancement of Analytical Methods

    Energy Technology Data Exchange (ETDEWEB)

    Preisler, Jan [Iowa State Univ., Ames, IA (United States)

    1997-01-01

    In this work, we use lasers to enhance possibilities of laser desorption methods and to optimize coating procedure for capillary electrophoresis (CE). We use several different instrumental arrangements to characterize matrix-assisted laser desorption (MALD) at atmospheric pressure and in vacuum. In imaging mode, 488-nm argon-ion laser beam is deflected by two acousto-optic deflectors to scan plumes desorbed at atmospheric pressure via absorption. All absorbing species, including neutral molecules, are monitored. Interesting features, e.g. differences between the initial plume and subsequent plumes desorbed from the same spot, or the formation of two plumes from one laser shot are observed. Total plume absorbance can be correlated with the acoustic signal generated by the desorption event. A model equation for the plume velocity as a function of time is proposed. Alternatively, the use of a static laser beam for observation enables reliable determination of plume velocities even when they are very high. Static scattering detection reveals negative influence of particle spallation on MS signal. Ion formation during MALD was monitored using 193-nm light to photodissociate a portion of insulin ion plume. These results define the optimal conditions for desorbing analytes from matrices, as opposed to achieving a compromise between efficient desorption and efficient ionization as is practiced in mass spectrometry. In CE experiment, we examined changes in a poly(ethylene oxide) (PEO) coating by continuously monitoring the electroosmotic flow (EOF) in a fused-silica capillary during electrophoresis. An imaging CCD camera was used to follow the motion of a fluorescent neutral marker zone along the length of the capillary excited by 488-nm Ar-ion laser. The PEO coating was shown to reduce the velocity of EOF by more than an order of magnitude compared to a bare capillary at pH 7.0. The coating protocol was important, especially at an intermediate pH of 7.7. The increase of p

  15. Laser: a Tool for Optimization and Enhancement of Analytical Methods

    Energy Technology Data Exchange (ETDEWEB)

    Preisler, Jan

    1997-01-01

    In this work, we use lasers to enhance possibilities of laser desorption methods and to optimize coating procedure for capillary electrophoresis (CE). We use several different instrumental arrangements to characterize matrix-assisted laser desorption (MALD) at atmospheric pressure and in vacuum. In imaging mode, 488-nm argon-ion laser beam is deflected by two acousto-optic deflectors to scan plumes desorbed at atmospheric pressure via absorption. All absorbing species, including neutral molecules, are monitored. Interesting features, e.g. differences between the initial plume and subsequent plumes desorbed from the same spot, or the formation of two plumes from one laser shot are observed. Total plume absorbance can be correlated with the acoustic signal generated by the desorption event. A model equation for the plume velocity as a function of time is proposed. Alternatively, the use of a static laser beam for observation enables reliable determination of plume velocities even when they are very high. Static scattering detection reveals negative influence of particle spallation on MS signal. Ion formation during MALD was monitored using 193-nm light to photodissociate a portion of insulin ion plume. These results define the optimal conditions for desorbing analytes from matrices, as opposed to achieving a compromise between efficient desorption and efficient ionization as is practiced in mass spectrometry. In CE experiment, we examined changes in a poly(ethylene oxide) (PEO) coating by continuously monitoring the electroosmotic flow (EOF) in a fused-silica capillary during electrophoresis. An imaging CCD camera was used to follow the motion of a fluorescent neutral marker zone along the length of the capillary excited by 488-nm Ar-ion laser. The PEO coating was shown to reduce the velocity of EOF by more than an order of magnitude compared to a bare capillary at pH 7.0. The coating protocol was important, especially at an intermediate pH of 7.7. The increase of p

  16. Models and Methods for Structural Topology Optimization with Discrete Design Variables

    DEFF Research Database (Denmark)

    Stolpe, Mathias

    Structural topology optimization is a multi-disciplinary research field covering optimal design of load carrying mechanical structures such as bridges, airplanes, wind turbines, cars, etc. Topology optimization is a collection of theory, mathematical models, and numerical methods and is often used...... such as bridges, airplanes, wind turbines, cars, etc. Topology optimization is a collection of theory, mathematical models, and numerical methods and is often used in the conceptual design phase to find innovative designs. The strength of topology optimization is the capability of determining both the optimal...... methods. The methods are often based on the concept of divide-and-conquer. Despite the proposed theoretical and numerical advances, this thesis clearly indicates that solving large-scale structural topology optimization problems with discrete design variables to proven global optimality is currently...

  17. Analyses of Methods and Algorithms for Modelling and Optimization of Biotechnological Processes

    Directory of Open Access Journals (Sweden)

    Stoyan Stoyanov

    2009-08-01

    Full Text Available A review of the problems in modeling, optimization and control of biotechnological processes and systems is given in this paper. An analysis of existing and some new practical optimization methods for searching global optimum based on various advanced strategies - heuristic, stochastic, genetic and combined are presented in the paper. Methods based on the sensitivity theory, stochastic and mix strategies for optimization with partial knowledge about kinetic, technical and economic parameters in optimization problems are discussed. Several approaches for the multi-criteria optimization tasks are analyzed. The problems concerning optimal controls of biotechnological systems are also discussed.

  18. The Multiobjective Trajectory Optimization for Hypersonic Glide Vehicle Based on Normal Boundary Intersection Method

    Directory of Open Access Journals (Sweden)

    Zhengnan Li

    2016-01-01

    Full Text Available To solve the multiobjective optimization problem on hypersonic glider vehicle trajectory design subjected to complex constraints, this paper proposes a multiobjective trajectory optimization method that combines the boundary intersection method and pseudospectral method. The multiobjective trajectory optimization problem (MTOP is established based on the analysis of the feature of hypersonic glider vehicle trajectory. The MTOP is translated into a set of general optimization subproblems by using the boundary intersection method and pseudospectral method. The subproblems are solved by nonlinear programming algorithm. In this method, the solution that has been solved is employed as the initial guess for the next subproblem so that the time consumption of the entire multiobjective trajectory optimization problem shortens. The maximal range and minimal peak heat problem is solved by the proposed method. The numerical results demonstrate that the proposed method can obtain the Pareto front of the optimal trajectory, which can provide the reference for the trajectory design of hypersonic glider vehicle.

  19. Experimental Optimization Methods for Multi-Element Airfoils

    Science.gov (United States)

    Landman, Drew; Britcher, Colin P.

    1996-01-01

    A modern three element airfoil model with a remotely activated flap was used to investigate optimum flap testing position using an automated optimization algorithm in wind tunnel tests. Detailed results for lift coefficient versus flap vertical and horizontal position are presented for two angles of attack: 8 and 14 degrees. An on-line first order optimizer is demonstrated which automatically seeks the optimum lift as a function of flap position. Future work with off-line optimization techniques is introduced and aerodynamic hysteresis effects due to flap movement with flow on are discussed.

  20. Genetic-evolution-based optimization methods for engineering design

    Science.gov (United States)

    Rao, S. S.; Pan, T. S.; Dhingra, A. K.; Venkayya, V. B.; Kumar, V.

    1990-01-01

    This paper presents the applicability of a biological model, based on genetic evolution, for engineering design optimization. Algorithms embodying the ideas of reproduction, crossover, and mutation are developed and applied to solve different types of structural optimization problems. Both continuous and discrete variable optimization problems are solved. A two-bay truss for maximum fundamental frequency is considered to demonstrate the continuous variable case. The selection of locations of actuators in an actively controlled structure, for minimum energy dissipation, is considered to illustrate the discrete variable case.

  1. Genetic-evolution-based optimization methods for engineering design

    Science.gov (United States)

    Rao, S. S.; Pan, T. S.; Dhingra, A. K.; Venkayya, V. B.; Kumar, V.

    1990-01-01

    This paper presents the applicability of a biological model, based on genetic evolution, for engineering design optimization. Algorithms embodying the ideas of reproduction, crossover, and mutation are developed and applied to solve different types of structural optimization problems. Both continuous and discrete variable optimization problems are solved. A two-bay truss for maximum fundamental frequency is considered to demonstrate the continuous variable case. The selection of locations of actuators in an actively controlled structure, for minimum energy dissipation, is considered to illustrate the discrete variable case.

  2. Oil Reservoir Production Optimization using Single Shooting and ESDIRK Methods

    DEFF Research Database (Denmark)

    Capolei, Andrea; Völcker, Carsten; Frydendall, Jan;

    2012-01-01

    Conventional recovery techniques enable recovery of 10-50% of the oil in an oil field. Advances in smart well technology and enhanced oil recovery techniques enable significant larger recovery. To realize this potential, feedback model-based optimal control technologies are needed to manipulate...... the injections and oil production such that flow is uniform in a given geological structure. Even in the case of conventional water flooding, feedback based optimal control technologies may enable higher oil recovery than with conventional operational strategies. The optimal control problems that must be solved...... for sensitivity computation. We demonstrate the procedure on a water ooding example with conventional injectors and producers....

  3. Optimizing Fungal DNA Extraction Methods from Aerosol Filters

    Science.gov (United States)

    Jimenez, G.; Mescioglu, E.; Paytan, A.

    2016-12-01

    Fungi and fungal spores can be picked up from terrestrial ecosystems, transported long distances, and deposited into marine ecosystems. It is important to study dust-borne fungal communities, because they can stay viable and effect the ambient microbial populations, which are key players in biogeochemical cycles. One of the challenges of studying dust-borne fungal populations is that aerosol samples contain low biomass, making extracting good quality DNA very difficult. The aim of this project was to increase DNA yield by optimizing DNA extraction methods. We tested aerosol samples collected from Haifa, Israel (polycarbonate filter), Monterey Bay, CA (quartz filter) and Bermuda (quartz filter). Using the Qiagen DNeasy Plant Kit, we tested the effect of altering bead beating times and incubation times, adding three freeze and thaw steps, initially washing the filters with buffers for various lengths of time before using the kit, and adding a step with 30 minutes of sonication in 65C water. Adding three freeze/thaw steps, adding a sonication step, washing with a phosphate buffered saline overnight, and increasing incubation time to two hours, in that order, resulted in the highest increase in DNA for samples from Israel (polycarbonate). DNA yield of samples from Monterey (quart filter) increased about 5 times when washing with buffers overnight (phosphate buffered saline and potassium phophate buffer), adding a sonication step, and adding three freeze and thaw steps. Samples collected in Bermuda (quartz filter) had the highest increase in DNA yield from increasing incubation to 2 hours, increasing bead beating time to 6 minutes, and washing with buffers overnight (phosphate buffered saline and potassium phophate buffer). Our results show that DNA yield can be increased by altering various steps of the Qiagen DNeasy Plant Kit protocol, but different types of filters collected at different sites respond differently to alterations. These results can be used as

  4. A topology optimization method based on the level set method for the design of negative permeability dielectric metamaterials

    DEFF Research Database (Denmark)

    Otomori, Masaki; Yamada, Takayuki; Izui, Kazuhiro;

    2012-01-01

    are highly impractical from an engineering and manufacturing point of view. Therefore, a topology optimization method that can obtain clear optimized configurations is desirable. Here, a level set-based topology optimization method incorporating a fictitious interface energy is applied to a negative......This paper presents a level set-based topology optimization method for the design of negative permeability dielectric metamaterials. Metamaterials are artificial materials that display extraordinary physical properties that are unavailable with natural materials. The aim of the formulated...... optimization problem is to find optimized layouts of a dielectric material that achieve negative permeability. The presence of grayscale areas in the optimized configurations critically affects the performance of metamaterials, positively as well as negatively, but configurations that contain grayscale areas...

  5. Iron Pole Shape Optimization of IPM Motors Using an Integrated Method

    Directory of Open Access Journals (Sweden)

    JABBARI, A.

    2010-02-01

    Full Text Available An iron pole shape optimization method to reduce cogging torque in Interior Permanent Magnet (IPM motors is developed by using the reduced basis technique coupled by finite element and design of experiments methods. Objective function is defined as the minimum cogging torque. The experimental design of Taguchi method is used to build the approximation model and to perform optimization. This method is demonstrated on the rotor pole shape optimization of a 4-poles/24-slots IPM motor.

  6. Using the Taguchi method for rapid quantitative PCR optimization with SYBR Green I.

    Science.gov (United States)

    Thanakiatkrai, Phuvadol; Welch, Lindsey

    2012-01-01

    Here, we applied the Taguchi method, an engineering optimization process, to successfully determine the optimal conditions for three SYBR Green I-based quantitative PCR assays. This method balanced the effects of all factors and their associated levels by using an orthogonal array rather than a factorial array. Instead of running 27 experiments with the conventional factorial method, the Taguchi method achieved the same optimal conditions using only nine experiments, saving valuable resources.

  7. A new method of determining the optimal embedding dimension based on nonlinear prediction

    Institute of Scientific and Technical Information of China (English)

    Meng Qing-Fang; Peng Yu-Hua; Xue Pei-Jun

    2007-01-01

    A new method is proposed to determine the optimal embedding dimension from a scalar time series in this paper. This method determines the optimal embedding dimension by optimizing the nonlinear autoregressive prediction model parameterized by the embedding dimension and the nonlinear degree. Simulation results show the effectiveness of this method. And this method is applicable to a short time series, stable to noise, computationally efficient, and without any purposely introduced parameters.

  8. Solving Nonlinear Optimization Problems of Real Functions in Complex Variables by Complex-Valued Iterative Methods.

    Science.gov (United States)

    Zhang, Songchuan; Xia, Youshen

    2016-12-28

    Much research has been devoted to complex-variable optimization problems due to their engineering applications. However, the complex-valued optimization method for solving complex-variable optimization problems is still an active research area. This paper proposes two efficient complex-valued optimization methods for solving constrained nonlinear optimization problems of real functions in complex variables, respectively. One solves the complex-valued nonlinear programming problem with linear equality constraints. Another solves the complex-valued nonlinear programming problem with both linear equality constraints and an ℓ₁-norm constraint. Theoretically, we prove the global convergence of the proposed two complex-valued optimization algorithms under mild conditions. The proposed two algorithms can solve the complex-valued optimization problem completely in the complex domain and significantly extend existing complex-valued optimization algorithms. Numerical results further show that the proposed two algorithms have a faster speed than several conventional real-valued optimization algorithms.

  9. Optimal design of structures for earthquake loads by a hybrid RBF-BPSO method

    Institute of Scientific and Technical Information of China (English)

    Eysa Salajegheh; Saeed Gholizadeh; Mohsen Khatibina

    2008-01-01

    The optimal seismic design of structures requires that time history analyses (THA) be carried out repeatedly. This makes the optimal design process inefficient, in particular, if an evolutionary algorithm is used. To reduce the overall time required for structural optimization, two artificial intelligence strategies are employed. In the first strategy, radial basis function (RBF) neural networks are used to predict the time history responses of structures in the optimization flow. In the second strategy, a binary particle swarm optimization (BPSO) is used to find the optimum design. Combining the RBF and BPSO, a hybrid RBF-BPSO optimization method is proposed in this paper, which achieves fast optimization with high computational performance. Two examples are presented and compared to determine the optimal weight of structures under earthquake loadings using both exact and approximate analyses. The numerical results demonstrate the computational advantages and effectiveness of the proposed hybrid RBF-BPSO optimization method for the seismic design of structures.

  10. Anti-vibration Optimization Design of Printed Circuit Board Based on Modal Analysis%基于模态分析的印制电路板抗振优化设计

    Institute of Scientific and Technical Information of China (English)

    陈康; 张雷; 胡晓吉

    2014-01-01

    To ensure a sufficiently high natural frequency of printed circuit board can effectively improve the anti -vibration capa-bility of the printed circuit board for .Two typical sizes of printed circuit board ( PCB) which are 3U and 6U are taken for exam-ple, their finite element models are established , and their natural frequencies are obtained by modal analysis .Optimal installation solutions are designed for 3U and 6U boards to solve their problems of low natural frequencies .The results show that the optimal installation solutions are easy to implement , they can significantly increase the natural frequencies for 3U and 6U boards and en-hance the anti-vibration reliability , at the same time the installation solutions meet the needs of circuit design .%保证印制电路板足够高的固有频率可有效提高印制电路板的抗振能力。以3U和6U两种典型尺寸的印制电路板为例,分别建立有限元模型,通过模态分析得到其各阶固有频率。针对印制电路板固有频率偏低的问题,分别对3U和6U板卡设计优化安装方案。模态分析表明,这些优化安装方案易于实现,可显著提高这2种板卡的固有频率,增强抗振能力,提高可靠性,同时考虑了电路设计的需要。

  11. An Efficient Primal-Dual Prox Method for Non-Smooth Optimization

    CERN Document Server

    Yang, Tianbao; Mehdavi, Mehrdad; Zhu, Shenghuo

    2012-01-01

    We consider the non-smooth optimization problems in machine learning, where both the loss function and the regularizer are non-smooth functions. Previous studies on efficient empirical loss minimization assume either a smooth loss function or a strongly convex regularizer, making them unsuitable for non-smooth optimization. We develop an efficient method for a family of non-smooth optimization where the dual form of the loss function is bilinear in primal and dual variables. We cast a non-smooth optimization problem into a minimax optimization problem, and develop a primal dual prox method that solves the minimax optimization problem at a rate of $O(1/T)$, significantly faster than a standard gradient descent method ($O(1/\\sqrt{T})$). Our empirical study verifies the efficiency of the proposed method for non-smooth optimization by comparing it to the state-of-the-art first order methods.

  12. Structural Topology Optimization : Basic Theory, Methods and Applications

    OpenAIRE

    2013-01-01

    The thesis is written as an introduction to topology optimization, aiming to help knowledge development in design optimization techniques, as well as aiding the adaptation of a sustainable culture with direct application to similar products like the two test cases supplied by the EC SuPLight project. These components are; a Door Connection Joint for a business jet and a Front Lower Control Arm from a McPherson suspension. The thesis has no intention of covering all aspects concerning topology...

  13. Gradient-based stochastic optimization methods in Bayesian experimental design

    OpenAIRE

    2012-01-01

    Optimal experimental design (OED) seeks experiments expected to yield the most useful data for some purpose. In practical circumstances where experiments are time-consuming or resource-intensive, OED can yield enormous savings. We pursue OED for nonlinear systems from a Bayesian perspective, with the goal of choosing experiments that are optimal for parameter inference. Our objective in this context is the expected information gain in model parameters, which in general can only be estimated u...

  14. Immune clonal selection optimization method with combining mutation strategies

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In artificial immune optimization algorithm, the mutation of immune cells has been considered as the key operator that determines the algorithm performance. Traditional immune optimization algorithms have used a single mutation operator, typically a Gaussian. Using a variety of mutation operators that can be combined during evolution to generate different probability density function could hold the potential for producing better solutions with less computational effort. In view of this, a linear combination...

  15. The Development and Optimization of Techniques for Monitoring Water Quality on-Board Spacecraft Using Colorimetric Solid-Phase Extraction (C-SPE)

    Energy Technology Data Exchange (ETDEWEB)

    Hill, April Ann [Iowa State Univ., Ames, IA (United States)

    2007-12-01

    The main focus of this dissertation is the design, development, and ground and microgravity validation of methods for monitoring drinking water quality on-board NASA spacecraft using clorimetric-solid phase extraction (C-SPE). The Introduction will overview the need for in-flight water quality analysis and will detail some of the challenges associated with operations in the absence of gravity. The ability of C-SPE methods to meet these challenges will then be discussed, followed by a literature review on existing applications of C-SPE and similar techniques. Finally, a brief discussion of diffuse reflectance spectroscopy theory, which provides a means for analyte identification and quantification in C-SPE analyses, is presented. Following the Introduction, four research chapters are presented as separate manuscripts. Chapter 1 reports the results from microgravity testing of existing C-SPE methods and procedures aboard NASA's C-9 microgravity simulator. Chapter 2 discusses the development of a C-SPE method for determining the total concentration of biocidal silver (i.e., in both dissolved and colloidal forms) in water samples. Chapter 3 presents the first application of the C-SPE technique to the determination of an organic analyte (i.e., formaldehyde). Chapter 4, which is a departure from the main focus of the thesis, details the results of an investigation into the effect of substrate rotation on the kinetics involved in the antigen and labeling steps in sandwich immunoassays. These research chapters are followed by general conclusions and a prospectus section.

  16. A new method to optimize natural convection heat sinks

    Science.gov (United States)

    Lampio, K.; Karvinen, R.

    2017-08-01

    The performance of a heat sink cooled by natural convection is strongly affected by its geometry, because buoyancy creates flow. Our model utilizes analytical results of forced flow and convection, and only conduction in a solid, i.e., the base plate and fins, is solved numerically. Sufficient accuracy for calculating maximum temperatures in practical applications is proved by comparing the results of our model with some simple analytical and computational fluid dynamics (CFD) solutions. An essential advantage of our model is that it cuts down on calculation CPU time by many orders of magnitude compared with CFD. The shorter calculation time makes our model well suited for multi-objective optimization, which is the best choice for improving heat sink geometry, because many geometrical parameters with opposite effects influence the thermal behavior. In multi-objective optimization, optimal locations of components and optimal dimensions of the fin array can be found by simultaneously minimizing the heat sink maximum temperature, size, and mass. This paper presents the principles of the particle swarm optimization (PSO) algorithm and applies it as a basis for optimizing existing heat sinks.

  17. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    2011-2015 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 411 members,representing a team of worldwide experts in surgery research.They are from 47 countries,including Argentina(3),Australia(13),Austria(4),Belarus(1),Belgium(3),Brazil(10),Canada(10),China(41),Czech Republic(1),Denmark

  18. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    2011-2015 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 411 members, representing a team of worldwide experts in surgery research. They are from 47 countries, including Argentina (3), Australia (13), Austria (4), Belarus (1), Belgium (3), Brazil (10), Canada (10), China (41), Czech Republic (1), Denmark (1), Egypt (3), Estonia (1), Finland

  19. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    2011-2015The World Journal of Gastrointestinal Oncology Editorial Board consists of 428 members,representing a team of worldwide experts in gastrointestinal oncology.They are from 40 countries,including Argentina(2),Australia(10),Belgium(5),Brazil(2),Canada(4),Chile(2),China(56),Czech Republic(1),Denmark(1),Finland(3),France

  20. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 523 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 40 countries, including Argentina (1), Australia (7), Austria (3), Belgium (6), Brazil (5),

  1. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 529 members, representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina (1),Australia (7),Austria (2),Belgium (6),Brazil (5),Bulgaria (1),Canada (18),Chile (1),China

  2. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    The World Journal of Biological Chemistry Editorial Board consists of 529 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7), Austria(2),Belgium(6),Brazil(5),Bulgaria(1),Canada(18),Chile(1),China(36),Czech Republic(1),Denmark

  3. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 391 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 38 countries, including Argentina (1), Australia (6), Austria (3), Belgium (6), Brazil (4), Bulgaria (1), Canada (15), Chile (1), China (28), Denmark (1), Finland (3), France

  4. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2009-2013The World Journal of Biological Chemistry Editorial Board consists of 529 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7),Austria(2),Belgium(6),

  5. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    2011-2015The World Journal of Diabetes Editorial Board now consists of 710 members,representing a team of worldwide experts in diabetes mellitus.They are from 56 countries,including Argentina(2),Australia(27),Austria(11),Belgium(5),Brazil(13),Canada(24),Chile(3),China(40),Cuba(1),Czech Republic(3),Denmark(15),Egypt(3),

  6. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2009-2013The World Journal of Biological Chemistry Editorial Board consists of 523 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 40 countries, including Argentina (1), Australia (7), Austria (3), Belgium (6), Brazil (5), Bulgaria (1), Canada (20), Chile (1), China (36), Czech Republic (1), Denmark

  7. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    2009-2013The World Journal of Biological Chemistry Editorial Board consists of 529 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7),Austria(2),Belgium(6),Brazil(5),Bulgaria(1),Canada(18),Chile(1),China(36),Czech Republic(1),Denmark

  8. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 529 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 40 countries, including Argentina (1), Australia (7), Austria (2), Belgium (6), Brazil (5), Bulgaria (1), Canada

  9. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 523 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 40 countries,including Argentina(1),Australia(7), Austria(3),Belgium(6),Brazil(5),Bulgaria(1),Canada(20),Chile(1),China(36),Czech Republic(1),Denmark

  10. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    2009-2013The World Journal of Biological Chemistry Editorial Board consists of 391 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 38 countries, including Argentina (1), Australia (6), Austria (3), Belgium (6), Brazil (4), Bulgaria (1), Canada (15), Chile (1), China (28), Denmark (1), Finland (3), France

  11. Board news

    NARCIS (Netherlands)

    NN,

    1994-01-01

    Thanks to the hospitality and arrangements of Professor IWATSUKI, the Board could meet during the XV International Botanical Congress. At the meeting Prof. LUCAS AND DR. Roos were re-appointed, whereas Dr. BURLEY was appointed to succeed Dr. STEVENS as representative of the Harvard University. The

  12. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members, representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research.They are from 36 countries,including Australia(6),Austria(2),Belgium(2),Brazil(1),Canada(7),China(19),Czech Republic(1)

  13. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members, representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research. They are from 36 countries, including Australia (6), Austria (2), Belgium (2), Brazil (1), Canada (7), China (19),

  14. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members,representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research.They are from 36 countries,including Australia (6),Austria (2),Belgium (2),Brazil

  15. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members,representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research.They are from 36 countries, including Australia(6),Austria(2),Belgium

  16. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members,representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research.They are from 36 countries,including Australia(6),Austria(2),Belgium(2),Brazil(1),Canada(7),China(19),Czech Republic(1),

  17. Looking to the Future of TESOL Teacher Education: Web-based Bulletin Board Discussions in a Methods Course.

    Science.gov (United States)

    Kamhi-Stein, Lia D.

    2000-01-01

    Examines the uses of CMC in English-as-a-Second-Language teacher education through examples of Web-based bulletin board discussion. Qualitative and quantitative analysis revealed differences in the structure of participation from the perspective of initiation, response, and evaluation moves as well as different levels of participation by the…

  18. New methods of seafarer's training: an internet "refresher course on first-aid and medical care on board".

    Science.gov (United States)

    Canals, M L

    1999-01-01

    Our objective is to facilitate seamen's health education, according to the recommendations of international organisations like IMO (STCW 1995) and EC (Directive 92/29): They recommend a refresher course on first-aid at least every 5 years for persons in charge of medical care on board. In Spain the transposition of this Directive was published (RD 258/99). So, we thought that in order to help seafarers and officers in their training in prevention and in solving health problems derived from their occupational risks on board, continuing education could be implemented using an innovative and adaptable tool. No first-aid course can be useful without practical exercises. The term "refresher" (in this paper) is a way of reminding what people have learnt and practised in a previous practical course. In 1998, the Spanish Society of Maritime Medicine promoted a pilot internet refresher course for seafarers in its web, URL: "http://www.semm.org/curso/pauxm.html++ +". There are 10 didactic units (resources for medical assistance on board, radio-medical advice, environmental problems, travel medicine, cardio-respiratory resuscitation, prevention of problems in diving, death on board, occupational risk prevention ... etc.). Hypertext linked keywords help the student to revise the subject, a teacher can counsel him by e-mail and a multiple choice test, and clinical cases are included to check the comprehension of the didactic units. A CD and an English version of the course is being prepared.

  19. Structural Optimization Design of Horizontal-Axis Wind Turbine Blades Using a Particle Swarm Optimization Algorithm and Finite Element Method

    Directory of Open Access Journals (Sweden)

    Pan Pan

    2012-11-01

    Full Text Available This paper presents an optimization method for the structural design of horizontal-axis wind turbine (HAWT blades based on the particle swarm optimization algorithm (PSO combined with the finite element method (FEM. The main goal is to create an optimization tool and to demonstrate the potential improvements that could be brought to the structural design of HAWT blades. A multi-criteria constrained optimization design model pursued with respect to minimum mass of the blade is developed. The number and the location of layers in the spar cap and the positions of the shear webs are employed as the design variables, while the strain limit, blade/tower clearance limit and vibration limit are taken into account as the constraint conditions. The optimization of the design of a commercial 1.5 MW HAWT blade is carried out by combining the above method and design model under ultimate (extreme flap-wise load conditions. The optimization results are described and compared with the original design. It shows that the method used in this study is efficient and produces improved designs.

  20. Feasibility Test of a Liquid Film Thickness Sensor on a Flexible Printed Circuit Board Using a Three-Electrode Conductance Method.

    Science.gov (United States)

    Lee, Kyu Byung; Kim, Jong Rok; Park, Goon Cherl; Cho, Hyoung Kyu

    2016-12-27

    Liquid film thickness measurements under temperature-varying conditions in a two-phase flow are of great importance to refining our understanding of two-phase flows. In order to overcome the limitations of the conventional electrical means of measuring the thickness of a liquid film, this study proposes a three-electrode conductance method, with the device fabricated on a flexible printed circuit board (FPCB). The three-electrode conductance method offers the advantage of applicability under conditions with varying temperatures in principle, while the FPCB has the advantage of usability on curved surfaces and in relatively high-temperature conditions in comparison with sensors based on a printed circuit board (PCB). Two types of prototype sensors were fabricated on an FPCB and the feasibility of both was confirmed in a calibration test conducted at different temperatures. With the calibrated sensor, liquid film thickness measurements were conducted via a falling liquid film flow experiment, and the working performance was tested.

  1. Development of Combinatorial Methods for Alloy Design and Optimization

    Energy Technology Data Exchange (ETDEWEB)

    Pharr, George M.; George, Easo P.; Santella, Michael L

    2005-07-01

    The primary goal of this research was to develop a comprehensive methodology for designing and optimizing metallic alloys by combinatorial principles. Because conventional techniques for alloy preparation are unavoidably restrictive in the range of alloy composition that can be examined, combinatorial methods promise to significantly reduce the time, energy, and expense needed for alloy design. Combinatorial methods can be developed not only to optimize existing alloys, but to explore and develop new ones as well. The scientific approach involved fabricating an alloy specimen with a continuous distribution of binary and ternary alloy compositions across its surface--an ''alloy library''--and then using spatially resolved probing techniques to characterize its structure, composition, and relevant properties. The three specific objectives of the project were: (1) to devise means by which simple test specimens with a library of alloy compositions spanning the range interest can be produced; (2) to assess how well the properties of the combinatorial specimen reproduce those of the conventionally processed alloys; and (3) to devise screening tools which can be used to rapidly assess the important properties of the alloys. As proof of principle, the methodology was applied to the Fe-Ni-Cr ternary alloy system that constitutes many commercially important materials such as stainless steels and the H-series and C-series heat and corrosion resistant casting alloys. Three different techniques were developed for making alloy libraries: (1) vapor deposition of discrete thin films on an appropriate substrate and then alloying them together by solid-state diffusion; (2) co-deposition of the alloying elements from three separate magnetron sputtering sources onto an inert substrate; and (3) localized melting of thin films with a focused electron-beam welding system. Each of the techniques was found to have its own advantages and disadvantages. A new and very

  2. Global Optimization Based on the Hybridization of Harmony Search and Particle Swarm Optimization Methods

    Directory of Open Access Journals (Sweden)

    A. P. Karpenko

    2014-01-01

    Full Text Available We consider a class of stochastic search algorithms of global optimization which in various publications are called behavioural, intellectual, metaheuristic, inspired by the nature, swarm, multi-agent, population, etc. We use the last term.Experience in using the population algorithms to solve challenges of global optimization shows that application of one such algorithm may not always effective. Therefore now great attention is paid to hybridization of population algorithms of global optimization. Hybrid algorithms unite various algorithms or identical algorithms, but with various values of free parameters. Thus efficiency of one algorithm can compensate weakness of another.The purposes of the work are development of hybrid algorithm of global optimization based on known algorithms of harmony search (HS and swarm of particles (PSO, software implementation of algorithm, study of its efficiency using a number of known benchmark problems, and a problem of dimensional optimization of truss structure.We set a problem of global optimization, consider basic algorithms of HS and PSO, give a flow chart of the offered hybrid algorithm called PSO HS , present results of computing experiments with developed algorithm and software, formulate main results of work and prospects of its development.

  3. Application of multi-stage Monte Carlo method for solving machining optimization problems

    Directory of Open Access Journals (Sweden)

    Miloš Madić

    2014-08-01

    Full Text Available Enhancing the overall machining performance implies optimization of machining processes, i.e. determination of optimal machining parameters combination. Optimization of machining processes is an active field of research where different optimization methods are being used to determine an optimal combination of different machining parameters. In this paper, multi-stage Monte Carlo (MC method was employed to determine optimal combinations of machining parameters for six machining processes, i.e. drilling, turning, turn-milling, abrasive waterjet machining, electrochemical discharge machining and electrochemical micromachining. Optimization solutions obtained by using multi-stage MC method were compared with the optimization solutions of past researchers obtained by using meta-heuristic optimization methods, e.g. genetic algorithm, simulated annealing algorithm, artificial bee colony algorithm and teaching learning based optimization algorithm. The obtained results prove the applicability and suitability of the multi-stage MC method for solving machining optimization problems with up to four independent variables. Specific features, merits and drawbacks of the MC method were also discussed.

  4. Reliability-based design optimization for flexible mechanism with particle swarm optimization and advanced extremum response surface method

    Institute of Scientific and Technical Information of China (English)

    张春宜; 宋鲁凯; 费成巍; 郝广平; 刘令君

    2016-01-01

    To improve the computational efficiency of the reliability-based design optimization (RBDO) of flexible mechanism, particle swarm optimization-advanced extremum response surface method (PSO-AERSM) was proposed by integrating particle swarm optimization (PSO) algorithm and advanced extremum response surface method (AERSM). Firstly, the AERSM was developed and its mathematical model was established based on artificial neural network, and the PSO algorithm was investigated. And then the RBDO model of flexible mechanism was presented based on AERSM and PSO. Finally, regarding cross-sectional area as design variable, the reliability optimization of flexible mechanism was implemented subject to reliability degree and uncertainties based on the proposed approach. The optimization results show that the cross-section sizes obviously reduce by 22.96 mm2 while keeping reliability degree. Through the comparison of methods, it is demonstrated that the AERSM holds high computational efficiency while keeping computational precision for the RBDO of flexible mechanism, and PSO algorithm minimizes the response of the objective function. The efforts of this work provide a useful sight for the reliability optimization of flexible mechanism, and enrich and develop the reliability theory as well.

  5. PCNN document segmentation method based on bacterial foraging optimization algorithm

    Science.gov (United States)

    Liao, Yanping; Zhang, Peng; Guo, Qiang; Wan, Jian

    2014-04-01

    Pulse Coupled Neural Network(PCNN) is widely used in the field of image processing, but it is a difficult task to define the relative parameters properly in the research of the applications of PCNN. So far the determination of parameters of its model needs a lot of experiments. To deal with the above problem, a document segmentation based on the improved PCNN is proposed. It uses the maximum entropy function as the fitness function of bacterial foraging optimization algorithm, adopts bacterial foraging optimization algorithm to search the optimal parameters, and eliminates the trouble of manually set the experiment parameters. Experimental results show that the proposed algorithm can effectively complete document segmentation. And result of the segmentation is better than the contrast algorithms.

  6. Intelligent and nature inspired optimization methods in medicine

    DEFF Research Database (Denmark)

    Marinakis, Yannis; Marinaki, Magdalene; Dounias, Georgios;

    2009-01-01

    , decrease noise and improve speed by the elimination of irrelevant or redundant features. The present paper deals with the optimization of nearest neighbour classifiers via intelligent and nature inspired algorithms for a very significant medical problem, the Pap smear cell classification problem......The classification problem consists of using some known objects, usually described by a large vector of features, to induce a model that classifies others into known classes. Feature selection is widely used as the first stage of the classification task to reduce the dimension of the problem....... The algorithms used include tabu search, genetic algorithms, particle swarm optimization and ant colony optimization. The proposed complete algorithmic scheme is tested on two sets of data. The first consists of 917 images of Pap smear cells and the second set consists of 500 images, classified carefully...

  7. A hybrid nonlinear programming method for design optimization

    Science.gov (United States)

    Rajan, S. D.

    1986-01-01

    Solutions to engineering design problems formulated as nonlinear programming (NLP) problems usually require the use of more than one optimization technique. Moreover, the interaction between the user (analysis/synthesis) program and the NLP system can lead to interface, scaling, or convergence problems. An NLP solution system is presented that seeks to solve these problems by providing a programming system to ease the user-system interface. A simple set of rules is used to select an optimization technique or to switch from one technique to another in an attempt to detect, diagnose, and solve some potential problems. Numerical examples involving finite element based optimal design of space trusses and rotor bearing systems are used to illustrate the applicability of the proposed methodology.

  8. Optimization of Classical Hydraulic Engine Mounts Based on RMS Method

    Directory of Open Access Journals (Sweden)

    J. Christopherson

    2005-01-01

    Full Text Available Based on RMS averaging of the frequency response functions of the absolute acceleration and relative displacement transmissibility, optimal parameters describing the hydraulic engine mount are determined to explain the internal mount geometry. More specifically, it is shown that a line of minima exists to define a relationship between the absolute acceleration and relative displacement transmissibility of a sprung mass using a hydraulic mount as a means of suspension. This line of minima is used to determine several optimal systems developed on the basis of different clearance requirements, hence different relative displacement requirements, and compare them by means of their respective acceleration and displacement transmissibility functions. In addition, the transient response of the mount to a step input is also investigated to show the effects of the optimization upon the time domain response of the hydraulic mount.

  9. Optimal reliability design method for remote solar systems

    Science.gov (United States)

    Suwapaet, Nuchida

    A unique optimal reliability design algorithm is developed for remote communication systems. The algorithm deals with either minimizing an unavailability of the system within a fixed cost or minimizing the cost of the system with an unavailability constraint. The unavailability of the system is a function of three possible failure occurrences: individual component breakdown, solar energy deficiency (loss of load probability), and satellite/radio transmission loss. The three mathematical models of component failure, solar power failure, transmission failure are combined and formulated as a nonlinear programming optimization problem with binary decision variables, such as number and type (or size) of photovoltaic modules, batteries, radios, antennas, and controllers. Three possible failures are identified and integrated in computer algorithm to generate the parameters for the optimization algorithm. The optimization algorithm is implemented with a branch-and-bound technique solution in MS Excel Solver. The algorithm is applied to a case study design for an actual system that will be set up in remote mountainous areas of Peru. The automated algorithm is verified with independent calculations. The optimal results from minimizing the unavailability of the system with the cost constraint case and minimizing the total cost of the system with the unavailability constraint case are consistent with each other. The tradeoff feature in the algorithm allows designers to observe results of 'what-if' scenarios of relaxing constraint bounds, thus obtaining the most benefit from the optimization process. An example of this approach applied to an existing communication system in the Andes shows dramatic improvement in reliability for little increase in cost. The algorithm is a real design tool, unlike other existing simulation design tools. The algorithm should be useful for other stochastic systems where component reliability, random supply and demand, and communication are

  10. A VIRTUAL MESH METHOD FOR THE OPTIMIZED DESIGN OF COMPLEX STRUCTURES

    Institute of Scientific and Technical Information of China (English)

    DuTaisheng; HllangRongjie; SongTianxia; ChenChuanyao

    2003-01-01

    Concepts for a virtual 3D space and a hyper-sphere are proposed and the formulae for determining the computable nodes of the mesh are derived. Then a new optimization design method ('Virtual Mesh Method' or V.M.M) is developed. Three examples are given, showing that the method proposed is especially suitable for the optimized design of complex structures, and that the global approximate optimal solution can be searched with remarkably reduced computational work.

  11. A numerical method for solving optimal control problems using state parametrization

    Science.gov (United States)

    Mehne, H.; Borzabadi, A.

    2006-06-01

    A numerical method for solving a special class of optimal control problems is given. The solution is based on state parametrization as a polynomial with unknown coefficients. This converts the problem to a non-linear optimization problem. To facilitate the computation of optimal coefficients, an improved iterative method is suggested. Convergence of this iterative method and its implementation for numerical examples are also given.

  12. SEQUENTIAL CONVEX PROGRAMMING METHODS FOR SOLVING LARGE TOPOLOGY OPTIMIZATION PROBLEMS: IMPLEMENTATION AND COMPUTATIONAL RESULTS

    Institute of Scientific and Technical Information of China (English)

    Qin Ni; Ch. Zillober; K. Schittkowski

    2005-01-01

    In this paper, we describe a method to solve large-scale structural optimization problems by sequential convex programming (SCP). A predictor-corrector interior point method is applied to solve the strictly convex subproblems. The SCP algorithm and the topology optimization approach are introduced. Especially, different strategies to solve certain linear systems of equations are analyzed. Numerical results are presented to show the efficiency of the proposed method for solving topology optimization problems and to compare different variants.

  13. Approximate Analytical Solutions of the Regularized Long Wave Equation Using the Optimal Homotopy Perturbation Method

    Directory of Open Access Journals (Sweden)

    Constantin Bota

    2014-01-01

    Full Text Available The paper presents the optimal homotopy perturbation method, which is a new method to find approximate analytical solutions for nonlinear partial differential equations. Based on the well-known homotopy perturbation method, the optimal homotopy perturbation method presents an accelerated convergence compared to the regular homotopy perturbation method. The applications presented emphasize the high accuracy of the method by means of a comparison with previous results.

  14. Topology Optimal Design of Material Microstructures Using Strain Energy-based Method

    Institute of Scientific and Technical Information of China (English)

    Zhang Weihong; Wang Fengwen; Dai Gaoming; Sun Shiping

    2007-01-01

    Sensitivity analysis and topology optimization of microstructures using strain energy-based method is presented. Compared with homogenization method, the strain energy-based method has advantages of higher computing efficiency and simplified programming.Both the dual convex programming method and perimeter constraint scheme are used to optimize the 2D and 3D microstructures. Numerical results indicate that the strain energy-based method has the same effectiveness as that of homogenization method for orthotropic materials.

  15. THE SATELLITE STRUCTURE TOPOLOGY OPTIMIZATION BASED ON HOMOGENIZATION METHOD AND ITS SIZE SENSITIVITY ANALYSIS

    Institute of Scientific and Technical Information of China (English)

    ChenChangya; PanJin; WangDeyu

    2005-01-01

    With the development of satellite structure technology, more and more design parameters will affect its structural performance. It is desirable to obtain an optimal structure design with a minimum weight, including optimal configuration and sizes. The present paper aims to describe an optimization analysis for a satellite structure, including topology optimization and size optimization. Based on the homogenization method, the topology optimization is carried out for the main supporting frame of service module under given constraints and load conditions, and then the sensitivity analysis is made of 15 structural size parameters of the whole satellite and the optimal sizes are obtained. The numerical result shows that the present optimization design method is very effective.

  16. Models and Methods for Structural Topology Optimization with Discrete Design Variables

    DEFF Research Database (Denmark)

    Stolpe, Mathias

    Structural topology optimization is a multi-disciplinary research field covering optimal design of load carrying mechanical structures such as bridges, airplanes, wind turbines, cars, etc. Topology optimization is a collection of theory, mathematical models, and numerical methods and is often used...... or stresses, or fundamental frequencies. The design variables are either continuous or discrete and model dimensions, thicknesses, densities, or material properties. Structural topology optimization is a multi-disciplinary research field covering optimal design of load carrying mechanical structures...... in the conceptual design phase to find innovative designs. The strength of topology optimization is the capability of determining both the optimal shape and the topology of the structure. In some cases also the optimal material properties can be determined. Optimal structural design problems are modeled...

  17. Taguchi Method Applied in Optimization of Shipley 5740 Positive Resist Deposition

    Science.gov (United States)

    Hui, Allan; Wiberg, Dean V.; Blosiu, Julian

    1997-01-01

    Taguchi Methods of Robust Design Presents a way to optimize output process performance through organized experiments, by using orthogonal arrays for the evaluation of the process controlleable parameters.

  18. Optimal traffic light control method for a single intersection based on hybrid systems

    Institute of Scientific and Technical Information of China (English)

    赵晓华; 陈阳舟; 崔平远

    2003-01-01

    A single intersection of two phases is selected as a model to put forward a new optimal time-planning scheme for traffic light based on the model of hybrid automata for single intersection. A method of optimization is proposed for hybrid systems, and the average queue length over all queues is used as an objective function to find an optimal switching scheme for traffic light. It is illustrated that traffic light control for single intersection is a typical hybrid system, and the optimal planning-time scheme can be obtained using the optimal hybrid systems control based on the two stages method.

  19. Overview: Applications of numerical optimization methods to helicopter design problems

    Science.gov (United States)

    Miura, H.

    1984-01-01

    There are a number of helicopter design problems that are well suited to applications of numerical design optimization techniques. Adequate implementation of this technology will provide high pay-offs. There are a number of numerical optimization programs available, and there are many excellent response/performance analysis programs developed or being developed. But integration of these programs in a form that is usable in the design phase should be recognized as important. It is also necessary to attract the attention of engineers engaged in the development of analysis capabilities and to make them aware that analysis capabilities are much more powerful if integrated into design oriented codes. Frequently, the shortcoming of analysis capabilities are revealed by coupling them with an optimization code. Most of the published work has addressed problems in preliminary system design, rotor system/blade design or airframe design. Very few published results were found in acoustics, aerodynamics and control system design. Currently major efforts are focused on vibration reduction, and aerodynamics/acoustics applications appear to be growing fast. The development of a computer program system to integrate the multiple disciplines required in helicopter design with numerical optimization technique is needed. Activities in Britain, Germany and Poland are identified, but no published results from France, Italy, the USSR or Japan were found.

  20. A monotonic method for solving nonlinear optimal control problems

    CERN Document Server

    Salomon, Julien

    2009-01-01

    Initially introduced in the framework of quantum control, the so-called monotonic algorithms have shown excellent numerical results when dealing with various bilinear optimal control problems. This paper aims at presenting a unified formulation of such procedures and the intrinsic assumptions they require. In this framework, we prove the feasibility of the general algorithm. Finally, we explain how these assumptions can be relaxed.

  1. A topology optimization method for design of negative permeability metamaterials

    DEFF Research Database (Denmark)

    Diaz, A. R.; Sigmund, Ole

    2010-01-01

    A methodology based on topology optimization for the design of metamaterials with negative permeability is presented. The formulation is based on the design of a thin layer of copper printed on a dielectric, rectangular plate of fixed dimensions. An effective media theory is used to estimate...... are presented for illustration. New metamaterial concepts are uncovered, beyond the classical split-ring inspired layouts....

  2. A method for optimizing the location of wind farms

    NARCIS (Netherlands)

    McWilliam, M.K.; Kooten, van G.C.; Crawford, C.

    2012-01-01

    The optimal location and configuration of wind farms in a large region is important information for policy makers, electricity system planners and wind farm developers. The model developed in this paper uses wind resource data, population data and transmission line locations to find the configuratio

  3. Research on inverse methods and optimization in Italy

    Science.gov (United States)

    Larocca, Francesco

    1991-01-01

    The research activities in Italy on inverse design and optimization are reviewed. The review is focused on aerodynamic aspects in turbomachinery and wing section design. Inverse design of blade rows and ducts of turbomachinery in subsonic and transonic regime are illustrated by the Politecnico di Torino and turbomachinery industry (FIAT AVIO).

  4. Resampling: an optimization method for inverse planning in robotic radiosurgery.

    Science.gov (United States)

    Schweikard, Achim; Schlaefer, Alexander; Adler, John R

    2006-11-01

    By design, the range of beam directions in conventional radiosurgery are constrained to an isocentric array. However, the recent introduction of robotic radiosurgery dramatically increases the flexibility of targeting, and as a consequence, beams need be neither coplanar nor isocentric. Such a nonisocentric design permits a large number of distinct beam directions to be used in one single treatment. These major technical differences provide an opportunity to improve upon the well-established principles for treatment planning used with GammaKnife or LINAC radiosurgery. With this objective in mind, our group has developed over the past decade an inverse planning tool for robotic radiosurgery. This system first computes a set of beam directions, and then during an optimization step, weights each individual beam. Optimization begins with a feasibility query, the answer to which is derived through linear programming. This approach offers the advantage of completeness and avoids local optima. Final beam selection is based on heuristics. In this report we present and evaluate a new strategy for utilizing the advantages of linear programming to improve beam selection. Starting from an initial solution, a heuristically determined set of beams is added to the optimization problem, while beams with zero weight are removed. This process is repeated to sample a set of beams much larger compared with typical optimization. Experimental results indicate that the planning approach efficiently finds acceptable plans and that resampling can further improve its efficiency.

  5. Hydrodynamic Optimization Method and Design Code for Stall-Regulated Hydrokinetic Turbine Rotors

    Energy Technology Data Exchange (ETDEWEB)

    Sale, D.; Jonkman, J.; Musial, W.

    2009-08-01

    This report describes the adaptation of a wind turbine performance code for use in the development of a general use design code and optimization method for stall-regulated horizontal-axis hydrokinetic turbine rotors. This rotor optimization code couples a modern genetic algorithm and blade-element momentum performance code in a user-friendly graphical user interface (GUI) that allows for rapid and intuitive design of optimal stall-regulated rotors. This optimization method calculates the optimal chord, twist, and hydrofoil distributions which maximize the hydrodynamic efficiency and ensure that the rotor produces an ideal power curve and avoids cavitation. Optimizing a rotor for maximum efficiency does not necessarily create a turbine with the lowest cost of energy, but maximizing the efficiency is an excellent criterion to use as a first pass in the design process. To test the capabilities of this optimization method, two conceptual rotors were designed which successfully met the design objectives.

  6. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>2014-2017 The World Journal of Hepatology Editorial Board consists of 469 members,representing a team of worldwide experts in hepatology.They are from 53 countries,including Algeria(1),Argentina(6),Armenia(1),Australia(1),Austria(4),Bangladesh(2),Belgium(3),Botswana(2),Brazil(13),Bulgaria(2),Canada(3),Chile(1),China(98),Czech Repoublic(1),Denmark(2),Egypt(12),France(6),Germany(19),Greece(11),Hungary(5),India(15),Indonesia

  7. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    2010-2013 The World Journal of Gastrointestinal Pharmacology and Therapeutics Editorial Board consists of 188 members, representing a team of worldwide experts in gastrointestinal pharmacology and therapeutics research. They are from 36 countries, including Australia (6), Austria (2), Belgium (2), Brazil (1), Canada (7), China (19), Czech (1), Denmark (1), Egypt (1), Estonia (1), Finland (1), France (1), Germany (5), Greece (4), Hungary (1), India (6), Iran (1), Ireland (1), Israel (3), Italy (20),

  8. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    2014-2017 The World Journal of Biological Chemistry Editorial Board consists of 473 members,representing a team of worldwide experts in biochemistry and molecular biology.They are from 47 countries,including Argentina(1),Australia(9),Austria(4),Belgium(5),Brazil(10),Canada(12),Chile(1),China(44),Cyprus(1),Czech Repoublic(1),Egypt(3),Finland(1),France(16),Germany(12),Greece(6),Hungary(1),India(8),Iran(3),Ireland(1),Israel(7),Italy

  9. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    2010-2015 The World Journal of Stem Cells Editorial Board consists of 719 members,representing a team of worldwide experts in infectious diseases.They are from 44 countries,including Argentina(2),Australia(10),Austria(6),Belgium(3),Brazil(10),Canada(16),China(74),Cyprus(1),Czech Republic(5),Denmark(7),Egypt(2),Finland(3),France(19),Germany(36),Greece(1),Hungary(3),India(10),Iran(9),Ireland(4),Israel(10),Italy(52),Japan(55),Jordan

  10. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    2014-2017The World Journal of Cardiology Editorial Board consists of 410 members,representing a team of worldwide experts in cardiology.They are from 46 countries,including Argentina(3),Australia(7),Austria(6),Belgium(2),Brazil(8),Canada(11),China(37),Croatia(1),Cuba(1),Cyprus(1),Czech Repoublic(2),Denmark(3),Egypt(1),Finland(3),France(3),Germany(31),Greece(10),Hungary(5),India(4),Iran(2),

  11. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2015-01-01

    <正>2014-2017The World Journal of Cardiology Editorial Board consists of 410 members,representing a team of worldwide experts in cardiology.They are from 46 countries,including Argentina(3),Australia(7),Austria(6),Belgium(2),Brazil(8),Canada(11),China(37),Croatia(1),Cuba(1),Cyprus(1),Czech Repoublic(2),Denmark(3),Egypt(1),Finland(3),France(3),Germany(31),Greece(10),Hungary(5),India(4),Iran(2),Ireland(1),Israel(4),Italy(61),Japan(32),Koso

  12. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 387 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 38 countries, including Argentina (1), Australia (5), Austria (3), Belgium (6), Brazil (4), Bulgaria (1), Canada (15), Chile (1), China (28), Denmark (1), Finland (3), France (11), Germany (15), Greece (2), India (9), Iran (2), Israel (4), Italy (22), Japan (29), Lithuania (1), Mauritius (1),

  13. Editorial Board

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    2009-2013 The World Journal of Biological Chemistry Editorial Board consists of 370 members, representing a team of worldwide experts in biochemistry and molecular biology. They are from 38 countries, including Argentina (1), Australia (5), Austria (3), Belgium (6), Brazil (3), Bulgaria (1), Canada (15), Chile (1), China (27), Denmark (1), Finland (3), France (10), Germany (15), Greece (2), India (8), Iran (2), Israel (3), Italy (21), Japan (28), Lithuania (1), Mauritius (1), Mexico

  14. Fuel-optimal low-thrust formation reconfiguration via Radau pseudospectral method

    Science.gov (United States)

    Li, Jing

    2016-07-01

    This paper investigates fuel-optimal low-thrust formation reconfiguration near circular orbit. Based on the Clohessy-Wiltshire equations, first-order necessary optimality conditions are derived from the Pontryagin's maximum principle. The fuel-optimal impulsive solution is utilized to divide the low-thrust trajectory into thrust and coast arcs. By introducing the switching times as optimization variables, the fuel-optimal low-thrust formation reconfiguration is posed as a nonlinear programming problem (NLP) via direct transcription using multiple-phase Radau pseudospectral method (RPM), which is then solved by a sparse nonlinear optimization software SNOPT. To facilitate optimality verification and, if necessary, further refinement of the optimized solution of the NLP, formulas for mass costate estimation and initial costates scaling are presented. Numerical examples are given to show the application of the proposed optimization method. To fix the problem, generic fuel-optimal low-thrust formation reconfiguration can be simplified as reconfiguration without any initial and terminal coast arcs, whose optimal solutions can be efficiently obtained from the multiple-phase RPM at the cost of a slight fuel increment. Finally, influence of the specific impulse and maximum thrust magnitude on the fuel-optimal low-thrust formation reconfiguration is analyzed. Numerical results shown the links and differences between the fuel-optimal impulsive and low-thrust solutions.

  15. Buddy Board

    DEFF Research Database (Denmark)

    Enggaard, Helle; Moselund, Lene

    2015-01-01

    Projekt ’BuddyBoard’ er kommet i stand via et samarbejde mellem Frederikshavn kommune, Bunker43 og Lab. X. Afdeling en ’Havly’ på Sæby Ældrecenter fungerer som living lab, hvilket betyder, at det udgør et levende laboratorium for udvikling og afprøvning af teknologi (Schultz, 2013). Projektet er....... Bunker43 har udviklet en teknologi (BuddyBoard) til hurtig formidling af billeder fra pårørende og personale til beboere på institutioner. Pårørende og personale uploader billeder via en APP eller en hjemmeside og har mulighed for at tilføje en kort forklarende tekst til hvert billede. Beboeren ser...... billederne via en tablet. Systemet bygger på et simpelt og brugervenligt design, så ældre med kognitive og/eller fysiske funktionsnedsættelser kan anvende teknologien. BuddyBoard fungerer via internettet, og billederne gemmes på en sikret server hos udbyderen, som er Bunker43. Intentionerne med BuddyBoard er...

  16. Research methods to develop Measures of Effectiveness of the United States Coast Guard`s Vessel Inspection and Boarding Program. Volume 2, Main report

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, T.; Cox, R. [Sandia National Labs., Albuquerque, NM (United States); Gawande, K. [New Mexico Univ., Albuquerque, NM (United States). Dept. of Economics; Stone, R.; Waisel, L.; Wallace, W.A. [Rensselaer Polytechnic Inst., Troy, New York (United States). Dept. of Decision Sciences and Engineering Systems

    1995-04-01

    The primary objective of this study is to provide Measures of Effectiveness (MOEs) of the US Coast Guard Marine Inspection and Boarding Program based on objective scientific methods. A secondary objective of the study is to provide USCG management with a methodologically and theoretically sound aid to effective policy decision-making. The MOEs constructed in this study are specific to the Marine Inspection and Boarding Program, but the methodology of the study is based on sound theoretical principles that are probably applicable to a range of USCG activities. Hence the methodology applied equally to other important USCG programs and can be similarly used to measure their effectiveness and as an aid to decision-making.

  17. A Method of Sharing Tacit Knowledge by a Bulletin Board Link to Video Scene and an Evaluation in the Field of Nursing Skill

    Science.gov (United States)

    Shimada, Satoshi; Azuma, Shouzou; Teranaka, Sayaka; Kojima, Akira; Majima, Yukie; Maekawa, Yasuko

    We developed the system that knowledge could be discovered and shared cooperatively in the organization based on the SECI model of knowledge management. This system realized three processes by the following method. (1)A video that expressed skill is segmented into a number of scenes according to its contents. Tacit knowledge is shared in each scene. (2)Tacit knowledge is extracted by bulletin board linked to each scene. (3)Knowledge is acquired by repeatedly viewing the video scene with the comment that shows the technical content to be practiced. We conducted experiments that the system was used by nurses working for general hospitals. Experimental results show that the nursing practical knack is able to be collected by utilizing bulletin board linked to video scene. Results of this study confirmed the possibility of expressing the tacit knowledge of nurses' empirical nursing skills sensitively with a clue of video images.

  18. A study of the optimization of board striding for taking off posture in long jump by applying simulation computation%运用仿真计算对跳远踏跳姿势的优化

    Institute of Scientific and Technical Information of China (English)

    罗炯; 公立政

    2012-01-01

      According to the characteristics of body movement at board striding for taking off in long jump, and by ap-plying a multiple rigid body model and modern computer simulation technology, the authors probed into the character-istics of changing of long jump farness caused by board striding in different postures, so as to seek for the optimal board striding for taking off posture, and revealed the following findings: different combinations of shank attitude angle and knee joint angle formed at board striding enable the body to reach the same farness, therefore it is obviously irra-tional to judge the performance of board striding technology based solely on the magnitude of board striding angle; at the moment of board striding for taking off in long jump, the magnitudes of influence of attitude angles of various body parts on long jump distance are different, the order of their importance is in turn the attitude angle of the shank of the take-off leg as the most important one, followed by the knee angle of the take-off leg, while the influence of torso tilting angle, thigh included angle and the knee angle of the swinging leg on long jump distance is relatively small; at the mo-ment a long jumper strides on the board for taking off in long jump, there certainly are an optimal knee joint angle of the take-off leg and an optimal included angle between the shank and the ground, which enable the long jumper to reach the farthest long jump distance if he/she strides on the board in such a way.%  运用多刚体模型及现代计算机仿真技术,探讨人体在不同姿势下踏板所引起的跳远远度的变化特征,以寻找最佳的起跳着板姿势。结果表明:着板时小腿的姿态角、膝关节角不同组合可以使人体获得相同的远度,故仅凭着板角的大小来衡量着板技术的优劣显然是不合理的;跳远踏跳着板时刻、人体各环节姿态角对跳远距离的影响作用大小并不一致,其重要

  19. Optimization of hydrofoil for tidal current turbine based on particle swarm optimization and computational fluid dynamic method

    Directory of Open Access Journals (Sweden)

    Zhang De-Sheng

    2016-01-01

    Full Text Available Both efficiency and cavitation performance of the hydrofoil are the key technologies to design the tidal current turbine. In this paper, the hydrofoil efficiency and lift coefficient were improved based on particle swarm optimization method and XFoil codes. The cavitation performance of the optimized hydrofoil was also discussed by the computational fluid dynamic. Numerical results show the efficiency of the optimized hydrofoil was improved 11% ranging from the attack angle of 0-7° compared to the original NACA63-818 hydrofoil. The minimum pressure on leading edge of the optimized hydrofoil dropped above 15% at the high attack angle conditions of 10°, 15°, and 20°, respectively, which is benefit for the hydrofoil to avoiding the cavitation.

  20. Autonomous guided vehicles methods and models for optimal path planning

    CERN Document Server

    Fazlollahtabar, Hamed

    2015-01-01

      This book provides readers with extensive information on path planning optimization for both single and multiple Autonomous Guided Vehicles (AGVs), and discusses practical issues involved in advanced industrial applications of AGVs. After discussing previously published research in the field and highlighting the current gaps, it introduces new models developed by the authors with the goal of reducing costs and increasing productivity and effectiveness in the manufacturing industry. The new models address the increasing complexity of manufacturing networks, due for example to the adoption of flexible manufacturing systems that involve automated material handling systems, robots, numerically controlled machine tools, and automated inspection stations, while also considering the uncertainty and stochastic nature of automated equipment such as AGVs. The book discusses and provides solutions to important issues concerning the use of AGVs in the manufacturing industry, including material flow optimization with A...

  1. Scalable Optimization Methods for Distribution Networks with High PV Integration

    Energy Technology Data Exchange (ETDEWEB)

    Guggilam, Swaroop S.; Dall' Anese, Emiliano; Chen, Yu Christine; Dhople, Sairaj V.; Giannakis, Georgios B.

    2016-07-01

    This paper proposes a suite of algorithms to determine the active- and reactive-power setpoints for photovoltaic (PV) inverters in distribution networks. The objective is to optimize the operation of the distribution feeder according to a variety of performance objectives and ensure voltage regulation. In general, these algorithms take a form of the widely studied ac optimal power flow (OPF) problem. For the envisioned application domain, nonlinear power-flow constraints render pertinent OPF problems nonconvex and computationally intensive for large systems. To address these concerns, we formulate a quadratic constrained quadratic program (QCQP) by leveraging a linear approximation of the algebraic power-flow equations. Furthermore, simplification from QCQP to a linearly constrained quadratic program is provided under certain conditions. The merits of the proposed approach are demonstrated with simulation results that utilize realistic PV-generation and load-profile data for illustrative distribution-system test feeders.

  2. Optimized Audio Classification and Segmentation Algorithm by Using Ensemble Methods

    OpenAIRE

    Saadia Zahid; Fawad Hussain; Muhammad Rashid; Muhammad Haroon Yousaf; Hafiz Adnan Habib

    2015-01-01

    Audio segmentation is a basis for multimedia content analysis which is the most important and widely used application nowadays. An optimized audio classification and segmentation algorithm is presented in this paper that segments a superimposed audio stream on the basis of its content into four main audio types: pure-speech, music, environment sound, and silence. An algorithm is proposed that preserves important audio content and reduces the misclassification rate without using large amount o...

  3. Methods for reliability based design optimization of structural components

    OpenAIRE

    Dersjö, Tomas

    2012-01-01

    Cost and quality are key properties of a product, possibly even the two most important. Onedefinition of quality is fitness for purpose. Load-bearing products, i.e. structural components,loose their fitness for purpose if they fail. Thus, the ability to withstand failure is a fundamentalmeasure of quality for structural components. Reliability based design optimization(RBDO) is an approach for development of structural components which aims to minimizethe cost while constraining the probabili...

  4. Multigrid Methods in Network Optimization: Overview and Appraisal

    Science.gov (United States)

    1994-03-01

    matrix and c is a given n-vector (a row vector). (NOTE: There are other versions of the lemma; this is taken from Bazaraa , Jarvis and Sherali, 1990). We...of A. C. KARUSH-KUHN-TUCKER (KKT) OPTIMALUTY CONDITIONS We take this version of the KKT ciptimality conditions from Bazaraa , Jarvis and Sherali, 1990...0, or 1. This fact allows for integer optimal solutions when both supplies and demands are integer values ( Bazaraa et al..., 1990) B. TRANSPORTATION

  5. Application of Artificial Intelligence Methods of Tool Path Optimization in CNC Machines: A Review

    Directory of Open Access Journals (Sweden)

    Khashayar Danesh Narooei

    2014-08-01

    Full Text Available Today, in most of metal machining process, Computer Numerical Control (CNC machine tools have been very popular due to their efficiencies and repeatability to achieve high accuracy positioning. One of the factors that govern the productivity is the tool path travel during cutting a work piece. It has been proved that determination of optimal cutting parameters can enhance the machining results to reach high efficiency and minimum the machining cost. In various publication and articles, scientist and researchers adapted several Artificial Intelligence (AI methods or hybrid method for tool path optimization such as Genetic Algorithms (GA, Artificial Neural Network (ANN, Artificial Immune Systems (AIS, Ant Colony Optimization (ACO and Particle Swarm Optimization (PSO. This study presents a review of researches in tool path optimization with different types of AI methods that show the capability of using different types of optimization methods in CNC machining process.

  6. NOVEL METHOD OF REALIZING THE OPTIMAL TRANSMISSION OF THE CRANK-AND-ROCKER MECHANISM DESIGN

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A novel method of realizing the optimal transmission of the crank-and-rocker mechanism is presented. The optimal combination design is made by finding the related optimal transmission parameters. The diagram of the optimal transmission is drawn. In the diagram, the relation among minimum transmission angle, the coefficient of travel speed variation, the oscillating angle of the rocker and the length of the bars is shown, concisely, conveniently and directly. The method possesses the main characteristic. That it is to achieve the optimal transmission parameters under the transmission angle by directly choosing in the diagram, according to the given requirements. The characteristics of the mechanical transmission can be improved to gain the optimal transmission effect by the method. Especially, the method is simple and convenient in practical use.

  7. Blade pitch optimization methods for vertical-axis wind turbines

    Science.gov (United States)

    Kozak, Peter

    Vertical-axis wind turbines (VAWTs) offer an inherently simpler design than horizontal-axis machines, while their lower blade speed mitigates safety and noise concerns, potentially allowing for installation closer to populated and ecologically sensitive areas. While VAWTs do offer significant operational advantages, development has been hampered by the difficulty of modeling the aerodynamics involved, further complicated by their rotating geometry. This thesis presents results from a simulation of a baseline VAWT computed using Star-CCM+, a commercial finite-volume (FVM) code. VAWT aerodynamics are shown to be dominated at low tip-speed ratios by dynamic stall phenomena and at high tip-speed ratios by wake-blade interactions. Several optimization techniques have been developed for the adjustment of blade pitch based on finite-volume simulations and streamtube models. The effectiveness of the optimization procedure is evaluated and the basic architecture for a feedback control system is proposed. Implementation of variable blade pitch is shown to increase a baseline turbine's power output between 40%-100%, depending on the optimization technique, improving the turbine's competitiveness when compared with a commercially-available horizontal-axis turbine.

  8. An Efficient Optimization Method for Solving Unsupervised Data Classification Problems

    Directory of Open Access Journals (Sweden)

    Parvaneh Shabanzadeh

    2015-01-01

    Full Text Available Unsupervised data classification (or clustering analysis is one of the most useful tools and a descriptive task in data mining that seeks to classify homogeneous groups of objects based on similarity and is used in many medical disciplines and various applications. In general, there is no single algorithm that is suitable for all types of data, conditions, and applications. Each algorithm has its own advantages, limitations, and deficiencies. Hence, research for novel and effective approaches for unsupervised data classification is still active. In this paper a heuristic algorithm, Biogeography-Based Optimization (BBO algorithm, was adapted for data clustering problems by modifying the main operators of BBO algorithm, which is inspired from the natural biogeography distribution of different species. Similar to other population-based algorithms, BBO algorithm starts with an initial population of candidate solutions to an optimization problem and an objective function that is calculated for them. To evaluate the performance of the proposed algorithm assessment was carried on six medical and real life datasets and was compared with eight well known and recent unsupervised data classification algorithms. Numerical results demonstrate that the proposed evolutionary optimization algorithm is efficient for unsupervised data classification.

  9. An Optimal Power Flow (OPF) Method with Improved Power System Stability

    DEFF Research Database (Denmark)

    Su, Chi; Chen, Zhe

    2010-01-01

    This paper proposes an optimal power flow (OPF) method taking into account small signal stability as additional constraints. Particle swarm optimization (PSO) algorithm is adopted to realize the OPF process. The method is programmed in MATLAB and implemented to a nine-bus test power system which...... has large-scale wind power integration. The results show the ability of the proposed method to find optimal (or near-optimal) operating points in different cases. Based on these results, the analysis of the impacts of wind power integration on the system small signal stability has been conducted....

  10. A Survey of Stochastic Simulation and Optimization Methods in Signal Processing

    Science.gov (United States)

    Pereyra, Marcelo; Schniter, Philip; Chouzenoux, Emilie; Pesquet, Jean-Christophe; Tourneret, Jean-Yves; Hero, Alfred O.; McLaughlin, Steve

    2016-03-01

    Modern signal processing (SP) methods rely very heavily on probability and statistics to solve challenging SP problems. SP methods are now expected to deal with ever more complex models, requiring ever more sophisticated computational inference techniques. This has driven the development of statistical SP methods based on stochastic simulation and optimization. Stochastic simulation and optimization algorithms are computationally intensive tools for performing statistical inference in models that are analytically intractable and beyond the scope of deterministic inference methods. They have been recently successfully applied to many difficult problems involving complex statistical models and sophisticated (often Bayesian) statistical inference techniques. This survey paper offers an introduction to stochastic simulation and optimization methods in signal and image processing. The paper addresses a variety of high-dimensional Markov chain Monte Carlo (MCMC) methods as well as deterministic surrogate methods, such as variational Bayes, the Bethe approach, belief and expectation propagation and approximate message passing algorithms. It also discusses a range of optimization methods that have been adopted to solve stochastic problems, as well as stochastic methods for deterministic optimization. Subsequently, areas of overlap between simulation and optimization, in particular optimization-within-MCMC and MCMC-driven optimization are discussed.

  11. A Global Optimal Coherence Method for Multi-baseline InSAR Elevation Inversion

    Directory of Open Access Journals (Sweden)

    HUA Fenfen

    2015-11-01

    Full Text Available A global optimal coherence method for elevation inversion from multi-baseline polarimetric InSAR data is proposed. The multi-baseline polarimetric InSAR data used in experiments were obtained by Chinese X-SAR system and Germany's E-SAR system. Through combining several full polarimetric InSAR images, the proposed method constructs the multi-baseline polarimetric InSAR coherency matrix, and solves the optimal interferograms under global optimal coherence criterion. The optimal interferograms generated by global optimal coherence method were used to calculate the elevation of target with multi-baseline InSAR elevation inversion method. The proposed method reduces the influence of different scattering centers effectively using multi-baseline InSAR, which improves the accuracy and reliability of the interferometric phase and eventually improves the accuracy of DEM. The results verify the validity of the proposed method.

  12. Bionic optimization in structural design stochastically based methods to improve the performance of parts and assemblies

    CERN Document Server

    Gekeler, Simon

    2016-01-01

    The book provides suggestions on how to start using bionic optimization methods, including pseudo-code examples of each of the important approaches and outlines of how to improve them. The most efficient methods for accelerating the studies are discussed. These include the selection of size and generations of a study’s parameters, modification of these driving parameters, switching to gradient methods when approaching local maxima, and the use of parallel working hardware. Bionic Optimization means finding the best solution to a problem using methods found in nature. As Evolutionary Strategies and Particle Swarm Optimization seem to be the most important methods for structural optimization, we primarily focus on them. Other methods such as neural nets or ant colonies are more suited to control or process studies, so their basic ideas are outlined in order to motivate readers to start using them. A set of sample applications shows how Bionic Optimization works in practice. From academic studies on simple fra...

  13. Second decision-making method of the fuzzy optimal model and its application

    Institute of Scientific and Technical Information of China (English)

    刘金禄; 陈守煜

    2004-01-01

    In the process of concept design offshore platforms, it is necessary to select the best from feasible alternatives through comparison and filtering. Fuzzy optimal selection in multiple stages is an useful method in engineering decisionmaking, but in some cases, it is difficult to make a distinction between the first alternative and the second. Therefore it is necessary to improve the fuzzy optimal selection method with multiple stages. In this paper, using fuzzy cross iteration optimal modeling, the weight sensitivity analysis is made firstly. Then a second decision-making method to solve fuzzy optimal problems is proposed. Its basic principle is the inverse reasoning in mathematics. This method expands the applied range of fuzzy optimal selection. Finally this method is used in the concept design of offshore platform. A case study shows that this method is scientific, reasonable and easy to use in practice.

  14. An iterative symplectic pseudospectral method to solve nonlinear state-delayed optimal control problems

    Science.gov (United States)

    Peng, Haijun; Wang, Xinwei; Zhang, Sheng; Chen, Biaosong

    2017-07-01

    Nonlinear state-delayed optimal control problems have complex nonlinear characters. To solve this complex nonlinear problem, an iterative symplectic pseudospectral method based on quasilinearization techniques, the dual variational principle and pseudospectral methods is proposed in this paper. First, the proposed method transforms the original nonlinear optimal control problem into a series of linear quadratic optimal control problems. Then, a symplectic pseudospectral method is developed to solve these converted linear quadratic state-delayed optimal control problems. Coefficient matrices in the proposed method are sparse and symmetric since the dual variational principle is used, which makes the proposed method highly efficient. Converged numerical solutions with high precision can be obtained after a few iterations due to the benefit of the local pseudospectral method and quasilinearization techniques. In the numerical simulations, other numerical methods were used for comparisons. The numerical simulation results show that the proposed method is highly accurate, efficient and robust.

  15. A Monte Carlo Method for Multi-Objective Correlated Geometric Optimization

    Science.gov (United States)

    2014-05-01

    performs a Monte Carlo optimization to provide geospatial intelligence on entity placement using OpenCL framework. The solutions for optimal...Geometric optimization,Monte Carlo method, parallel computing, OpenCL 22 Song J. Park 410-278-5444Unclassified Unclassified Unclassified UU ii...given threat and target positions, and • AMonte Carlo method development in the OpenCL programming model for vendor-agnostic architecture support and

  16. DMTO – a method for Discrete Material and Thickness Optimization of laminated composite structures

    DEFF Research Database (Denmark)

    Sørensen, Søren Nørgaard; Sørensen, Rene; Lund, Erik

    2014-01-01

    are optimized simultaneously through interpolation functions with penalization. Numerical results for several parameterizations of a finite element model of a generic main spar from a wind turbine blade are presented. The different parameterizations represent different levels of complexity with respect......This paper presents a gradient based topology optimization method for Discrete Material and Thickness Optimization of laminated composite structures, labelled the DMTOmethod. The capabilities of the proposed method are demonstrated on mass minimization, subject to constraints on the structural...

  17. Pension Fund Governing Board

    CERN Multimedia

    HR Department

    2008-01-01

    Note The CERN pension scheme is based on the principle of defined benefits, so beneficiaries continue to receive the benefits to which they are entitled in accordance with the Rules of the Pension Fund. This means that pension entitlements under the Rules are not directly affected by the financial crisis and the current economic situation. However, the adjustment of pensions to the cost of living is not automatic and, under the method applied since 2006, must take into account the Fund’s financial position. Meeting of the Pension Fund Governing Board The Pension Fund Governing Board held its eighth meeting at ESO in Garching, Germany (near Munich) on 24 October 2008. Before starting its work, the Governing Board had the privilege of hearing an opening address by Professor Tim de Zeeuw, the Director General of ESO. Professor de Zeeuw described the mission of ESO and the ambitious projects of his organisation, which performs astronomy observations using telescopes located in...

  18. Pseudospectral method based trajectory optimization and fairing rejection time analysis of solid launch vehicle

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The problem of real-time trajectory optimization for small solid launch vehicle of operational responsive space (ORS) was studied by using pseudospectral method. According to the characteristic of the trajectory design, the dynamics model was set up in the inertia right-angled reference frame, and the equation and parameter at the orbit injection point were simplified and converted. The infinite dimension dynamic optimal control problem was converted to a finite dimension static state optimization problem and the algorithm reduced the complexity so as to become a general algorithm in trajectories optimization. With the trajectories optimization of a three-stage solid vehicle with a liquor upper stage as example, the model of the trajectory optimization was set up and simulations were carried out. The results demonstrated the advantage and validity of the pseudospectral method. The rejection time of fairing was also analyzed by the simulation results, and the optimal flight procedure and trajectory were obtained.

  19. Research on Poka Yoke Methods in Circuit Board Test%电路板自动测试中的防差错技术研究

    Institute of Scientific and Technical Information of China (English)

    霍晓磊; 康霞; 谭业双

    2014-01-01

    ATS ( Automatic Test System) is a developing trend in the circuit board test. Error and mistake proofing is taken into con-sideration in the design of ATS. It directly affects its reliability, safety and efficiency, especial y, when many kinds of circuit boards exist in the system. Some kinds of typical measures are introduced in this paper. The specific design methods of adapter, circuit board and cable are described in detail.%自动测试是目前电路板测试发展的主要趋势,而防差错设计是自动测试系统设计时需要考虑的问题之一,尤其在被测单元种类很多的情况下,防差错设计直接影响到系统的可靠性、安全性和工作效率,更应该引起重视。根据实际工程经验着重阐述了电路板自动测试中所采取的防差错措施,描述了实际工程中适配器、电路板、电缆和软件防差错的实现方法。

  20. Development Optimization and Uncertainty Analysis Methods for Oil and Gas Reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Ettehadtavakkol, Amin, E-mail: amin.ettehadtavakkol@ttu.edu [Texas Tech University (United States); Jablonowski, Christopher [Shell Exploration and Production Company (United States); Lake, Larry [University of Texas at Austin (United States)

    2017-04-15

    Uncertainty complicates the development optimization of oil and gas exploration and production projects, but methods have been devised to analyze uncertainty and its impact on optimal decision-making. This paper compares two methods for development optimization and uncertainty analysis: Monte Carlo (MC) simulation and stochastic programming. Two example problems for a gas field development and an oilfield development are solved and discussed to elaborate the advantages and disadvantages of each method. Development optimization involves decisions regarding the configuration of initial capital investment and subsequent operational decisions. Uncertainty analysis involves the quantification of the impact of uncertain parameters on the optimum design concept. The gas field development problem is designed to highlight the differences in the implementation of the two methods and to show that both methods yield the exact same optimum design. The results show that both MC optimization and stochastic programming provide unique benefits, and that the choice of method depends on the goal of the analysis. While the MC method generates more useful information, along with the optimum design configuration, the stochastic programming method is more computationally efficient in determining the optimal solution. Reservoirs comprise multiple compartments and layers with multiphase flow of oil, water, and gas. We present a workflow for development optimization under uncertainty for these reservoirs, and solve an example on the design optimization of a multicompartment, multilayer oilfield development.